A study of mortars prepared with fly ash and silica fume for use in structures exposed to marine enviroments

Directory of Open Access Journals (Sweden)

Hernández, Y.

2003-12-01

Full Text Available The purpose of this study is to evaluate different mortar mixtures containing 5, 10 and 1 5% P/P silica fume and 5, 10, 12.5, 15 and 17.5% P/P fly ash to be used for repairing/constructing reinforced concrete structures exposed to marine environments. These were evaluated from the following standpoints: physical-chemical (capillary absorption and effective porosity; mechanical (compressive strength; electrochemical (lineal polarization, cyclic polarización and rapid chloride permeation; morphological (scanning electron microscopy. Results showed that 15 % silica fume mixture with no fly ash gave the best performance from both the physical-mechanical as well as the economic standpoint.

El presente trabajo tiene como finalidad evaluar diferentes mezclas de mortero con contenidos de 5, 10 y 15 % P/P de microsílica y contenidos de 5, 10, 12,5, 15 y 17,5 % P/P de ceniza volante para ser utilizadas en la reparación/construcción de estructuras de concreto armado expuestas a ambientes marinos. Se evaluaron desde el punto de vista físico-químico (absorción capilar y porosidad efectiva, mecánico (resistencia a la compresión, electroquímico (polarización lineal, polarización cíclica y permeabilidad rápida de cloruros y su morfología por medio de microscopía electrónica de barrido. Los resultados permitieron seleccionar la mezcla conteniendo 15 % de microsílica sin ceniza volante, tanto desde el punto de vista físico-mecánico y electroquímico como económico.

Silica fume effect on retention characteristics of portland cement for uranium (VI)

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2005-01-01

With simulated groundwater as leachant, the retention capabilities of the portland cement, which contains different amount of silica fume, are investigated under 25 degree C and 42 days. The results indicate that silica fume can improve the retention capabilities of portland cement for uranium. When the cement contains 15% silica fume, the diffusion coefficient is 7 x 10 -3 cm 3 · -1 . It is only 5.5% of the cement without containing fume. (authors)

Mechanism of alkalinity lowering and chemical equilibrium model of high fly ash silica fume cement

International Nuclear Information System (INIS)

Hoshino, Seiichi; Honda, Akira; Negishi, Kumi

2014-01-01

The mechanism of alkalinity lowering of a High Fly ash Silica fume Cement (HFSC) under liquid/solid ratio conditions where the pH is largely controlled by the soluble alkali components (Region I) has been studied. This mechanism was incorporated in the chemical equilibrium model of HFSC. As a result, it is suggested that the dissolution and precipitation behavior of SO 4 2- partially contributes to alkalinity lowering of HFSC in Region I. A chemical equilibrium model of HFSC incorporating alkali (Na, K) adsorption, which was presumed as another contributing factor of the alkalinity lowering effect, was also developed, and an HFSC immersion experiment was analyzed using the model. The results of the developed model showed good agreement with the experiment results. From the above results, it was concluded that the alkalinity lowering of HFSC in Region I was attributed to both the dissolution and precipitation behavior of SO 4 2- and alkali adsorption, in addition to the absence of Ca(OH) 2 . A chemical equilibrium model of HFSC incorporating alkali and SO 4 2- adsorption was also proposed. (author)

Reaction products of densified silica fume agglomerates in concrete

International Nuclear Information System (INIS)

Diamond, Sidney; Sahu, Sadananda; Thaulow, Niels

2004-01-01

Most silica fume currently used in concrete is in the dry densified form and consists of agglomerates of sizes between 10 μm and several millimeters. Many of these agglomerates may break down only partially in normal concrete mixing. Examination of various mature silica-fume-bearing concretes using backscatter mode scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) analysis shows that such agglomerates have reacted in situ and given rise to recognizable types of reaction products filling the space within the original outline of the agglomerate. One type is 'quiescent', and usually shows no evidence of volume instability. EDX spectra indicate that the product formed within such grains is C-S-H of very low Ca/Si ratio, with modest alkali contents. Other silica fume agglomerates may undergo a distinct alkali-silica-type reaction (ASR), with the reaction product found within the original outline of the agglomerate having significantly less calcium and usually much higher alkali contents than the quiescent type. Such reacted agglomerates show evidence of local expansion, shrinkage cracking (on drying), and other features common to ASR. Both types may be found within the same concrete, sometimes in close proximity. It further appears that exposure to seawater may convert previously formed reaction products of silica fume agglomerates to magnesium silicate hydrates

Effect of Silica fume and superplasticizer on steel-concrete bond

International Nuclear Information System (INIS)

Esfahani, M. R.

2001-01-01

This paper presents a study on the influence of silica fume and super plasticizer on bond strength. The study included tests of fifty short length pull-out specimens in five series. The effect of silica fume and super plasticizer on bond strength was evaluated separately by tests of specimens made of concretes with similar strengths but different admixtures. Test results showed that the addition of silica fume in the concrete mixture had not a negative effect on bond strength. Also, there was not a considerable decrease in bond strength of specimens made of concrete with super plasticizer. Comparing the measured bond strengths normalized with respect to the square root of the concrete compressive strength, it was seen that the normalized bond strength increased with the concrete strength. this result agrees with the model previously proposed by the author for local bond strength. For the specimens made of high strength concrete including silica fume and super plasticizer, the normalized bond strength did not increase with the concrete strength

FABRICATION AND CHARACTERIZATION OF POLYIMIDE/POLYETHERSULFONE-FUMED SILICA MIXED MATRIX MEMBRANE FOR GAS SEPARATION

Directory of Open Access Journals (Sweden)

A. F. Ismail

2012-01-01

Full Text Available This study is performed primarily to investigate the feasibility of fumed silica as inorganic material towards gas separation performance of mixed matrix membrane. In this study, polyimide/polyethersulfone (PES-fumed silica mixed matrix membranes were casted using dry/wet technique. The results from the FESEM, DSC and FTIR analysis confirmed that the structure and physical properties of membrane is influenced by inorganic filler. FESEM’s cross-section view indicated good compatibility between polymer and fumed silica for all of range fumed silica used in this study. The gas separation performance of the mixed matrix membranes with fumed silica were relatively higher compared to that of the neat PI/PES membrane. PI/PES-fumed silica 5 wt% yielded significant selectivity enhancement of 7.21 and 40.47 for O2/N2, and CO2/CH4, respectively.

Crosslinkable fumed silica-based nanocomposite electrolytes for rechargeable lithium batteries

Energy Technology Data Exchange (ETDEWEB)

Li, Yangxing; Yerian, Jeffrey A.; Khan, Saad A.; Fedkiw, Peter S. [Department of Chemical & amp; Biomolecular Engineering, North Carolina State University, Raleigh, NC 27695-7905 (United States)

2006-10-27

Electrochemical and rheological properties are reported of composite polymer electrolytes (CPEs) consisting of dual-functionalized fumed silica with methacrylate and octyl groups+low-molecular weight poly(ethylene glycol) dimethyl ether (PEGdm)+lithium bis(trifluoromethanesulfonyl)imide (LiTFSI, lithium imide)+butyl methacrylate (BMA). The role of butyl methacrylate, which aids in formation of a crosslinked network by tethering adjacent fumed silica particles, on rheology and electrochemistry is examined together with the effects of fumed silica surface group, fumed silica weight percent, salt concentration, and solvent molecular weight. Chemical crosslinking of the fumed silica with 20% BMA shows a substantial increase in the elastic modulus of the system and a transition from a liquid-like/flocculated state to an elastic network. In contrast, no change in lithium transference number and only a modest decrease (factor of 2) on conductivity of the CPE are observed, indicating that a crosslinked silica network has minimal effect on the mechanism of ionic transport. These trends suggest that the chemical crosslinks occur on a microscopic scale, as opposed to a molecular scale, between adjacent silica particles and therefore do not impede the segmental mobility of the PEGdm. The relative proportion of the methacrylate and octyl groups on the silica surface displays a nominal effect on both rheology and conductivity following crosslinking although the pre-cure rheology is a function of the surface groups. Chemical crosslinked nanocomposite polymer electrolytes offer significant higher elastic modulus and yield stress than the physical nanocomposite counterpart with a small/negligible penalty of transport properties. The crosslinked CPEs exhibit good interfacial stability with lithium metal at open circuit, however, they perform poorly in cycling of lithium-lithium cells. (author)

Danish Investigations on Silica Fume Concretes at Elevated Temperatures

DEFF Research Database (Denmark)

Hertz, Kristian Dahl

1992-01-01

Describes fire tests in which the increased risk of explosive spalling of concrete densified by silica fume was first discovered. Further results are discussed from tests to define appropriate limits of silica fume content and to develop a new concrete for slender column units. Observations are m...... are made about circumstances under which superplasticizing additives in concrete gave rise to the development of toxic gases....

Investigations on the tensile strength of high performance concrete incorporating silica fume

International Nuclear Information System (INIS)

Santanu Bhanja; Bratish Sengupta

2005-01-01

Though the literature is rich in reporting on silica fume concrete the technical data on tensile strength is quite limited. The present paper is directed towards developing a better understanding on the isolated contribution of silica fume on the tensile strengths of High Performance Concrete. Extensive experimentation was carried out over water-binder ratios ranging from 0.26 to 0.42 and silica fume binder ratios from 0.0 to 0.3. For all the mixes compressive, flexural and split tensile strengths were determined at 28 days. The results of the present investigation indicate that silica fume incorporation results in significant improvements in the tensile strengths of concrete. It is also observed that the optimum replacement percentage, which led to maximization of strength, is not a constant one but depends on the water- cementitious material ratio of the mix. Compared to split tensile strengths, flexural strengths have exhibited greater percentage gains in strength. Increase in split tensile strength beyond 15% silica fume replacement is almost insignificant whereas sizeable gains in flexural tensile strength have occurred even up to 25% replacements. For the present investigation transgranular failure of concrete was observed which indicate that silica fume incorporation results in significant improvements in the strength of both paste and transition zone. (authors)

Investigation of durability of silica fume concretes in coastal structures within tidal zone

International Nuclear Information System (INIS)

Ganjian, E.; Sadeghi Pouya, H.

2003-01-01

In recent decade use of silica fume has been become greater in coastal concrete structures in the persona gulf, to increase durability of those establishments. In this research the durability of cement passers and concrete cubes with use of 7 and 10 percent of silica fume as a cement replacement have been investigated in three curing conditions (fresh water, coast of sea and simulation bonds) by measuring compressive strengths and capillary absorption. Silica fume specimens under wetting and drying condition showed more strength loss after 180 days compare to samples without silica fume or cured in the fresh water. In addition the greater silica fume amount in specimens cured within tidal zone and under wetting and drying simulation, the more water absorption by capillary. According to the results, good correspondence between simulated condition and real site exposure was obtained

Effects of Calcined clay minerals and Silica fume on the compressive strength of concrete

Directory of Open Access Journals (Sweden)

Abolfazl Soltani

2017-05-01

Full Text Available Pozzolanic materials are well known as potential replacements for cement manufacturing in order to increase compressive strength and improve durability of concrete in different environments and leading to save energy particularly reducing global warming effect. The present study reveals the effect of calcined clay minerals as natural pozzolanic material, separately and in combination with and without silica fume. To achieve this aim, 15 mixed designs with a constant water to cementitious ratio of  0.38 is made. In six mixed designs only metakaolin, zeolite or silica fume  and in eight other designs metakaolin and silica fume or zeolite and silica fume have been combined. Mixes containing metakaolin or zeolite with ratio of 10 or 20 percent and silica fume with 7 or 10 percent show significant increasing in compressive strength and improving durability, being valuable replacement for cement (in percentages. In particular, the best practice is attributed to the age of 28 days for compressive strength the replacement of the composition is 10% zeolite with 7% of silica fume and for electrical resistance the replacement of the composition is 10% zeolite with 7% of silica fume.

Effects of densified silica fume on microstructure and compressive strength of blended cement pastes

International Nuclear Information System (INIS)

Ji Yajun; Cahyadi, Jong Herman

2003-01-01

Some experimental investigations on the microstructure and compressive strength development of silica fume blended cement pastes are presented in this paper. The silica fume replacement varies from 0% to 20% by weight and the water/binder ratio (w/b) is 0.4. The pore structure by mercury intrusion porosimetry (MIP), the micromorphology by scanning electron microscopy (SEM) and the compressive strength at 3, 7, 14, 28, 56 and 90 days have been studied. The test results indicate that the improvements on both microstructure and mechanical properties of hardened cement pastes by silica fume replacement are not effective due to the agglomeration of silica fume particles. The unreacted silica fume remained in cement pastes, the threshold diameter was not reduced and the increase in compressive strength was insignificant up to 28 days. It is suggested that the proper measures should be taken to disperse silica fume agglomeration to make it more effective on improving the properties of materials

Influence of polyolefin fibers on the engineering properties of cement-based composites containing silica fume

International Nuclear Information System (INIS)

Han, Ta-Yuan; Lin, Wei-Ting; Cheng, An; Huang, Ran; Huang, Chin-Cheng

2012-01-01

Highlights: ► Experimental study is focus on the engineering properties of cement-based composites. ► Different mixes containing fiber and silica fume proportions have been tested. ► The influence of different mixes on the engineering properties has been discussed. ► The properties are included strength, ductility, permeability and microstructure. -- Abstract: This study evaluated the mechanical properties of cement-based composites produced with added polyolefin fibers and silica fume. Material variables included the water-cementitious ratio, the dosage of silica fume, and the length and dosage of polyolefin fiber. Researchers conducted tests on compressive strength, splitting tensile strength, direct tensile strength, resistivity, rapid chloride penetration, and initial surface absorption, and performed microscopic observation. Test results indicate that the specimens containing silica fume have higher compressive strength than the control and specimen made with fibers. The specimens with polyolefin fiber and silica fume have considerably higher tensile strength and ductility than the control and specimens made with silica fume. The specimens containing silica fume and polyolefin fiber demonstrated better resistance to chloride penetration than composites with polyolefin fiber or silica fume. For a given volume fraction, short polyolefin fiber performs better than its long counterpart in improving the properties of concrete. Specimens containing silica fume demonstrated a significant increase in resistivity and decrease in the total charge passed and absorption. Scanning electron microscopy illustrates that the polyolefin fiber acts to arrest the propagation of internal cracks.

The mechanism of cesium immobilization in densified silica-fume blended cement pastes

International Nuclear Information System (INIS)

Bar-Nes, G.; Katz, A.; Peled, Y.; Zeiri, Y.

2008-01-01

The role of silica-fume agglomerates, found in densified silica-fume (DSF) pastes, in the immobilization mechanism of Cs ions was studied. Samples of cementitious pastes containing two different forms of silica fume - DSF and raw silica fume (RSF) - were prepared. Leaching experiments showed that both additives reduced the leachability of the metal ion, but the effect of the DSF paste was much stronger. Scanning Electron Microscopy, together with Differential Thermal Analysis, proved that no agglomerated particles were present in the RSF pastes and that the extent of pozzolanic reactivity was higher. We therefore believe that unreacted silica within the DSF agglomerates adsorbs Cs ions and consequently increases their immobilization. Furthermore, this work suggests that during the pozzolanic reaction, a hydrated rim develops around the agglomerate that acts as an additional diffusion barrier for the Cs ions, resulting in an increased efficiency of Cs immobilization

Improvement of RVNRL film properties by adding fumed silica and hydroxy apatite

Directory of Open Access Journals (Sweden)

Adul Thiangchanya

2003-01-01

Full Text Available The effect of adding fumed silica and hydroxy apatite to Radiation Vulcanized Natural Rubber Latex (RVNRL for improving tear strength, aging properties, degradability and water-soluble protein content of rubber films has been investigated. The addition of fumed silica and hydroxy apatite in RVNRL improves tear strength and aging properties of rubber films, whereas tensile strength and degradability of rubber films were unchanged during storage at room temperature. The water-soluble protein content in rubber films was reduced by immobilization of the fumed silica and hydroxy apatite and enhanced by addition of ZnO. This may reduce allergy problems of natural rubber latex products caused by water-soluble protein. The MST of the RVNRL with fumed silica and hydroxy apatite indicated that the latex must be used within two months after mixing because of its stability.

Development of UHPC mixtures utilizing natural and industrial waste materials as partial replacements of silica fume and sand.

Science.gov (United States)

Ahmad, Shamsad; Hakeem, Ibrahim; Maslehuddin, Mohammed

2014-01-01

In the exploratory study presented in this paper, an attempt was made to develop different mixtures of ultrahigh performance concrete (UHPC) using various locally available natural and industrial waste materials as partial replacements of silica fume and sand. Materials such as natural pozzolana (NP), fly ash (FA), limestone powder (LSP), cement kiln dust (CKD), and pulverized steel slag (PSS), all of which are abundantly available in Saudi Arabia at little or no cost, were employed in the development of the UHPC mixtures. A base mixture of UHPC without replacement of silica fume or sand was selected and a total of 24 trial mixtures of UHPC were prepared using different percentages of NP, FA, LSP, CKD, and PSS, partially replacing the silica fume and sand. Flow and 28-d compressive strength of each UHPC mixture were determined to finally select those mixtures, which satisfied the minimum flow and strength criteria of UHPC. The test results showed that the utilization of NP, FA, LSP, CKD, and PSS in production of UHPC is possible with acceptable flow and strength. A total of 10 UHPC mixtures were identified with flow and strength equal to or more than the minimum required.

Highly Efficient Fumed Silica Nanoparticles for Peptide Bond Formation: Converting Alanine to Alanine Anhydride.

Science.gov (United States)

Guo, Chengchen; Jordan, Jacob S; Yarger, Jeffery L; Holland, Gregory P

2017-05-24

In this work, thermal condensation of alanine adsorbed on fumed silica nanoparticles is investigated using thermal analysis and multiple spectroscopic techniques, including infrared (IR), Raman, and nuclear magnetic resonance (NMR) spectroscopies. Thermal analysis shows that adsorbed alanine can undergo thermal condensation, forming peptide bonds within a short time period and at a lower temperature (∼170 °C) on fumed silica nanoparticle surfaces than that in bulk (∼210 °C). Spectroscopic results further show that alanine is converted to alanine anhydride with a yield of 98.8% during thermal condensation. After comparing peptide formation on solution-derived colloidal silica nanoparticles, it is found that fumed silica nanoparticles show much better efficiency and selectivity than solution-derived colloidal silica nanoparticles for synthesizing alanine anhydride. Furthermore, Raman spectroscopy provides evidence that the high efficiency for fumed silica nanoparticles is likely related to their unique surface features: the intrinsic high population of strained ring structures present at the surface. This work indicates the great potential of fumed silica nanoparticles in synthesizing peptides with high efficiency and selectivity.

Formulation and characterization of date palm fibers mortar by addition of silica fume

Science.gov (United States)

Mokhtari, A.; Kriker, A.; Ouaggad, H.; Merad, N.

2018-05-01

This paper presents the results of experimental investigations of the formulated and characterization of date palm fibers mortar by addition of silica fume. The use of addition mineral is widely used in the production of cements through the world. The objective of this work is to bring our contribution to the recovery of local resources in the occurrence vegetable fibers of date palm to weak cost and from renewable source and integrate it in the filled of building. Date palm fiber are from Ouargla town in south of Algeria. Different mortar mixtures were prepared in which the cement was substitute by 10% of silica fume. The mechanical characteristics (compressive and flexural strength) of date palm fibers mortar by treatment of the matrix by the adding of silica fume were examined. The results obtained have shown that the mortar workability as well as the compressive and flexural strength decreases with increasing the silica fume replacement. The results showed that the use of silica fume enabled to evaluate the flexural strength. However, another treatment of fibers and matrix will be recommended for Improved the characteristics.

Determining the Compressive, Flexural and Splitting Tensile Strength of Silica Fume Reinforced Lightweight Foamed Concrete

Directory of Open Access Journals (Sweden)

Mydin M.A.O.

2014-01-01

Full Text Available This study investigated the performance of the properties of foamed concrete in replacing volumes of cement of 10%, 15% and 20% by weight. A control unit of foamed concrete mixture made with ordinary Portland cement (OPC and 10%, 15% and 20% silica fume was prepared. Three mechanical property parameters were studied such as compressive strength, flexural strength and splitting tensile of foamed concrete with different percentages of silica fume. Silica fume is commonly used to increase the mechanical properties of concrete materials and it is also chosen due to certain economic reasons. The foamed concrete used in this study was cured at a relative humidity of 70% and a temperature of ±28°C. The improvement of mechanical properties was due to a significant densification in the microstructure of the cement paste matrix in the presence of silica fume hybrid supplementary binder as observed from micrographs obtained in the study. The overall results showed that there is a potential to utilize silica fume in foamed concrete, as there was a noticeable enhancement of thermal and mechanical properties with the addition of silica fume.

Development of UHPC Mixtures Utilizing Natural and Industrial Waste Materials as Partial Replacements of Silica Fume and Sand

Directory of Open Access Journals (Sweden)

Shamsad Ahmad

2014-01-01

Full Text Available In the exploratory study presented in this paper, an attempt was made to develop different mixtures of ultrahigh performance concrete (UHPC using various locally available natural and industrial waste materials as partial replacements of silica fume and sand. Materials such as natural pozzolana (NP, fly ash (FA, limestone powder (LSP, cement kiln dust (CKD, and pulverized steel slag (PSS, all of which are abundantly available in Saudi Arabia at little or no cost, were employed in the development of the UHPC mixtures. A base mixture of UHPC without replacement of silica fume or sand was selected and a total of 24 trial mixtures of UHPC were prepared using different percentages of NP, FA, LSP, CKD, and PSS, partially replacing the silica fume and sand. Flow and 28-d compressive strength of each UHPC mixture were determined to finally select those mixtures, which satisfied the minimum flow and strength criteria of UHPC. The test results showed that the utilization of NP, FA, LSP, CKD, and PSS in production of UHPC is possible with acceptable flow and strength. A total of 10 UHPC mixtures were identified with flow and strength equal to or more than the minimum required.

Pemanfaatan Mikrobakteri Terhadap Beton Mutu Tinggi dengan Tambahan Silica Fume

Directory of Open Access Journals (Sweden)

Azwar Annas

2016-04-01

Full Text Available Beton mutu tinggi adalah beton yang kuat tekan tinggi sekitar 50 MPa – 100 MPa. Untuk meningkatkan kuat tekan, material pozollan seperti silica fume dan flyash biasanya digunakan untuk mengganti material beton Dalam laporan ini, beton mutu tinggi dengan silica fume sebagai pengganti semen dipelajari. Kadar silica fume yang digunakan adalah 0%, 5%, 7,5% dan 10%. Selain itu pengaruh dari mikrobakteri juga dipelajari. Faktor water per binder yang dipakai adalah 25% dari berat binder, dan untuk membuat workabilitynya bagus maka digunakan superplasticizer. Kadar superplasticizer yang digunakan dicari lewat trial pengujian di laboratorium. Pengujian yang dilakukan pada umur 1, 3, 7, 14, 21, 28 adalah uji tekan pasta, mortar dan beton, selain itu pada benda uji beton umur 28 hari akan dilakukan uji split beton dan uji porositas. Dari hasil penelitian didapatkan kuat tekan beton tertinggi pada umur 28 hari (B7,5M adalah 69,71 MPa, sedangkan variasi silica fume yang paling optimum ada pada kadar 7,5%. Penambahan mikrobakteri tidak berpengaruh pada berat volume beton tetapi berpengaruh pada kuat tekan beton tersebut. Dengan penambahan mikrobakteri maka kuat tekan beton meningkat sebesar ± 30%. Sedangkan porositas total dan porositas tertutup yang terjadi pada beton semakin kecil, ini dibuktikan dengan hasil SEM terlihat bahwa bakteri mengisi area antara aggregat dan matrix beton.

Experimental investigation on high performance RC column with manufactured sand and silica fume

Science.gov (United States)

Shanmuga Priya, T.

2017-11-01

In recent years, the use High Performance Concrete (HPC) has increased in construction industry. The ingredients of HPC depend on the availability and characteristics of suitable alternative materials. Those alternative materials are silica fume and manufactured sand, a by products from ferro silicon and quarry industries respectively. HPC made with silica fume as partial replacement of cement and manufactured sand as replacement of natural sand is considered as sustainable high performance concrete. In this present study the concrete was designed to get target strength of 60 MPa as per guide lines given by ACI 211- 4R (2008). The laboratory study was carried out experimentally to analyse the axial behavior of reinforced cement HPC column of size 100×100×1000mm and square in cross section. 10% of silica fume was preferred over ordinary portland cement. The natural sand was replaced by 0, 20, 40, 60, 80 and 100% with Manufactured Sand (M-Sand). In this investigation, totally 6 column specimens were cast for mixes M1 to M6 and were tested in 1000kN loading frame at 28 days. From this, Load-Mid height deflection curves were drawn and compared. Maximum ultimate load carrying capacity and the least deflection is obtained for the mix prepared by partial replacement of cement with 10% silica fume & natural sand by 100% M-Sand. The fine, amorphous and pozzalonic nature of silica fume and fine mineral particles in M- Sand increased the stiffness of HPC column. The test results revealed that HPC can be produced by using M-Sand with silica fume.

Influence of polyacrylic ester and silica fume on the mechanical properties of mortar for repair application

Directory of Open Access Journals (Sweden)

Chaohua Jiang

2016-12-01

Full Text Available Experimental investigations on the influence of different amounts of polyacrylic ester and silica fumes on the mechanical properties of mortar such as the compressive strength, splitting tensile strength, bonding strength, and abrasion resistance are presented in this article. The results show that the compressive and splitting tensile strength of mortar can be improved with the addition of polyacrylic ester and silica fumes. Results obtained from both the direct tensile bond test and flexural bond test indicate that the addition of polyacrylic ester and silica fumes improves the bond strength significantly, and the enhancement is more obvious with polyacrylic ester paste as interfacial adhesives. Furthermore, mortar incorporation of polyacrylic ester and silica fumes shows superior abrasion resistance compared to the control mortar. Therefore, the correct combination of polyacrylic ester and silica fumes to produce mortars has been shown to have synergistic effects, which results in excellent properties including high bond strength and superior abrasion resistance. Mortars containing polyacrylic ester and silica fumes are ideal for repairing concrete especially for hydraulic concrete structure.

In situ polymerization of L-Lactide in the presence of fumed silica

International Nuclear Information System (INIS)

Prebe, A.; Alcouffe, P.; Cassagnau, Ph.; Gerard, J.F.

2010-01-01

Chemiorheology, i.e. rheological changes during the polymerization, of a biosourced monomer, i.e. L-Lactide, containing fumed silica have been studied. For that purpose, the reaction was proceeded in situ between the plates of a dynamic rheometer. The polymerization kinetics was followed from the variation of the complex shear modulus versus reaction time. Moreover, at temperatures lower than the crystallization temperature, it was possible to follow the crystallization process while the polymerization takes place. Adding fumed silica particles into the monomer leads to the formation of a physical (percolated) network from particle-particle interactions, i.e. silica, in the L-Lactide probably hydrophilic interactions. The gel-like structure was kept while the polymerization as long as the strain remains low indicating that the silica particle network remains weak. Furthermore, the mechanism of the break down of the gel structure under large deformation as well as the recovery was discussed. It seems that the non-linearity effect of the nanocomposites stems in the silica inter-particle interactions. It was found that silica particles do not have any effect on the temperature of crystallization - molar mass relation but could act as nucleating agent. In situ polymerization of L-Lactide in the presence of 5 wt.% of modified fumed silica was carried out in a reactor. It was found that fumed hydrophilic silica leaded to a microcomposite with highly dense agglomerates in the polymer matrix whereas with a less hydrophilic silica it was possible to decrease the size of the agglomerates increasing the dispersion. The finest dispersion state was achieved with the 'initiating' functionalized silica leading to a 'grafting from' polymerization of the L-Lactide. Such functionalized silica leads to a nanoscale dispersion in a one-step bulk polymerization with only a few small agglomerates.

In situ polymerization of L-Lactide in the presence of fumed silica

Energy Technology Data Exchange (ETDEWEB)

Prebe, A. [Universite de Lyon, F-69361, Lyon (France); CNRS, UMR 5223, Ingenierie des Materiaux Polymeres, F-69622, Villeurbanne (France); Universite Claude Bernard Lyon 1, F-69622, Villeurbanne (France); INSA Lyon, F-69621, Villeurbanne (France); Alcouffe, P. [Universite de Lyon, F-69361, Lyon (France); CNRS, UMR 5223, Ingenierie des Materiaux Polymeres, F-69622, Villeurbanne (France); Universite Claude Bernard Lyon 1, F-69622, Villeurbanne (France); Cassagnau, Ph., E-mail: philippe.cassagnau@univ-lyon1.fr [Universite de Lyon, F-69361, Lyon (France); CNRS, UMR 5223, Ingenierie des Materiaux Polymeres, F-69622, Villeurbanne (France); Universite Claude Bernard Lyon 1, F-69622, Villeurbanne (France); Gerard, J.F. [Universite de Lyon, F-69361, Lyon (France); CNRS, UMR 5223, Ingenierie des Materiaux Polymeres, F-69622, Villeurbanne (France); INSA Lyon, F-69621, Villeurbanne (France)

2010-11-01

Chemiorheology, i.e. rheological changes during the polymerization, of a biosourced monomer, i.e. L-Lactide, containing fumed silica have been studied. For that purpose, the reaction was proceeded in situ between the plates of a dynamic rheometer. The polymerization kinetics was followed from the variation of the complex shear modulus versus reaction time. Moreover, at temperatures lower than the crystallization temperature, it was possible to follow the crystallization process while the polymerization takes place. Adding fumed silica particles into the monomer leads to the formation of a physical (percolated) network from particle-particle interactions, i.e. silica, in the L-Lactide probably hydrophilic interactions. The gel-like structure was kept while the polymerization as long as the strain remains low indicating that the silica particle network remains weak. Furthermore, the mechanism of the break down of the gel structure under large deformation as well as the recovery was discussed. It seems that the non-linearity effect of the nanocomposites stems in the silica inter-particle interactions. It was found that silica particles do not have any effect on the temperature of crystallization - molar mass relation but could act as nucleating agent. In situ polymerization of L-Lactide in the presence of 5 wt.% of modified fumed silica was carried out in a reactor. It was found that fumed hydrophilic silica leaded to a microcomposite with highly dense agglomerates in the polymer matrix whereas with a less hydrophilic silica it was possible to decrease the size of the agglomerates increasing the dispersion. The finest dispersion state was achieved with the 'initiating' functionalized silica leading to a 'grafting from' polymerization of the L-Lactide. Such functionalized silica leads to a nanoscale dispersion in a one-step bulk polymerization with only a few small agglomerates.

Thermogravimetric analyses and mineralogical study of polymer modified mortar with silica fume

Directory of Open Access Journals (Sweden)

Alessandra Etuko Feuzicana de Souza Almeida

2006-09-01

Full Text Available Mineral and organic additions are often used in mortars to improve their properties. Microstructural investigation concerning the effects of styrene acrylic polymer and silica fume on the mineralogical composition of high-early-strength portland cement pastes after 28 days of hydration are presented in this paper. Thermogravimetry and derivative thermogravimetry were used to study the interaction between polymers and cement, as well as the extent of pozzolanic reaction of the mortars with silica fume. Differential scanning calorimetry and X ray diffraction were used to investigate the cement hydration and the effect of the additions. The results showed that the addition of silica fume and polymer reduces the portlandite formation due to delaying of Portland cement hydration and pozzolanic reaction.

Addition of Silica Fume to Improve Strength of Cement Paste

Science.gov (United States)

Chen, Jiajian; Chen, Hongniao; Li, Gu

2018-03-01

This study measured the packing densities of 0 to 30% silica fume (SF) added cementitious materials and strength of the cementitious pastes with various water content. The results revealed that addition of silica fume up to a certain level has great effects on packing density and strength. In-depth analysis illustrated that a lower W/CM ratio would not always result in a higher cube strength, and the range between 0.05 and 0.07 µm would be the amount of water film thickness (WFT) for muximum strength.

Determining the Compressive, Flexural and Splitting Tensile Strength of Silica Fume Reinforced Lightweight Foamed Concrete

OpenAIRE

Mydin M.A.O.; Sani N. Md.; Mohd Yusoff M.A.; Ganesan S.

2014-01-01

This study investigated the performance of the properties of foamed concrete in replacing volumes of cement of 10%, 15% and 20% by weight. A control unit of foamed concrete mixture made with ordinary Portland cement (OPC) and 10%, 15% and 20% silica fume was prepared. Three mechanical property parameters were studied such as compressive strength, flexural strength and splitting tensile of foamed concrete with different percentages of silica fume. Silica fume is commonly used to increase the m...

INFLUENCE OF SUBSTITUTION OF ORDINARY PORTLAND CEMENT BY SILICA FUME ON THE HYDRATION OF SLAG-PORTLAND CEMENT PASTES

Directory of Open Access Journals (Sweden)

E.A. El-Alfi

2011-06-01

Full Text Available Effect of gradual substitution of ordinary Portland cement by a few percent of silica fume (0.0, 2.5, 5.0 and 7.5 wt.% on the hydration properties of slag-Portland cement pastes up to 12 months was investigated. The results show that the composite cement pastes containing silica fume give the higher physico-mechanical properties than that of the slag-Portland cement. Also, the XRD results reveal that the peak of Ca(OH2 shows higher intensity in the sample without silica fume and completely disappears in the sample containing 7.5 wt.% silica fume content. Also, the intensity peaks of C4AH13 sharply increase with silica fume content.

Dynamic Moisture Sorption and Desorption in Fumed Silica-filled Silicone Foam

Energy Technology Data Exchange (ETDEWEB)

Trautschold, Olivia Carol [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-02

Characterizing dynamic moisture sorption and desorption in fumed silica-filled silicone foam is necessary for determining material compatibilities and life predictions, particularly in sealed environments that may be exposed to a range of environmental conditions. Thermogravimetric analysis (TGA) and near infrared spectroscopy (NIR) were performed on S5470 fumed silica-filled silicone foam to determine the weight percent of moisture at saturation. Additionally, TGA was used to determine the time, temperature, and relative humidity levels required for sorption and desorption of physisorbed moisture in S5470.

Comparative Study on the Performance of Blended and Nonblended Fly Ash Geopolymer Composites as Durable Construction Materials

Directory of Open Access Journals (Sweden)

Debabrata Dutta

2018-01-01

Full Text Available This article represents that the mechanical and microstructural properties and durability of fly ash-based geopolymers blended with silica fume and borax are better than those of conventional fly ash-based geopolymers. Fly ash itself contains the sources of silica and alumina which are required for geopolymerisation. But a sufficient amount of high-reactive silica is able to rapidly initiate geopolymerisation with activation. Pure potassium hydroxide pellets and sodium silicate solution were used for preparation of alkaline activator solution. Fly ash geopolymer paste exhibited better mechanical properties in the presence of silica fume with slight portion of borax. The effect of silica fume-blended geopolymer paste on temperature fluctuation (heating and cooling cycle at certain temperatures showed better performance than nonblended fly ash-based specimens. Durability property was evaluated by immersion of geopolymer specimens in 10% magnesium sulfate solution for a period of one year. The change in weight, strength, and microstructure was studied and compared. In the magnesium sulfate solution, a significant drop of strength to around 37.26% occurred after one year for nonblended fly ash-based specimens. It is evident that specimens prepared incorporating silica fume had the best performance in terms of their properties.

Testing Silica Fume-Based Concrete Composites under Chemical and Microbiological Sulfate Attacks

Directory of Open Access Journals (Sweden)

Adriana Estokova

2016-04-01

Full Text Available Current design practices based on descriptive approaches to concrete specification may not be appropriate for the management of aggressive environments. In this study, the durability of cement-based materials with and without the addition of silica fume, subjected to conditions that leach calcium and silicon, were investigated. Chemical corrosion was simulated by employing various H2SO4 and MgSO4 solutions, and biological corrosion was simulated using Acidithiobacillus sp. bacterial inoculation, leading to disrupted and damaged surfaces; the samples’ mass changes were studied following both chemical and biological attacks. Different leaching trends were observed via X-ray fluorescence when comparing chemical with biological leaching. Lower leaching rates were found for concrete samples fortified with silica fume than those without silica fume. X-ray diffraction and scanning electron microscopy confirmed a massive sulfate precipitate formation on the concrete surface due to bacterial exposure.

Development of UHPC Mixtures Utilizing Natural and Industrial Waste Materials as Partial Replacements of Silica Fume and Sand

OpenAIRE

Ahmad, Shamsad; Hakeem, Ibrahim; Maslehuddin, Mohammed

2014-01-01

In the exploratory study presented in this paper, an attempt was made to develop different mixtures of ultrahigh performance concrete (UHPC) using various locally available natural and industrial waste materials as partial replacements of silica fume and sand. Materials such as natural pozzolana (NP), fly ash (FA), limestone powder (LSP), cement kiln dust (CKD), and pulverized steel slag (PSS), all of which are abundantly available in Saudi Arabia at little or no cost, were employed in the de...

Performance of Portland cement mixes containing silica fume and mixed with lime-water

Directory of Open Access Journals (Sweden)

Metwally A.A. Abd Elaty

2014-12-01

Test results show that using lime-water in mixing enhances consistency degree compared to the corresponding control mixes. Furthermore, it delays both initial and final setting times compared with traditional water due to the common ion effect principles. Moreover, combined use of lime-water and silica fume enhances the pozzolanic reaction that was identified by the strength development at both early and later ages. The existence of CH crystals for higher percentages of silica fume (up to 30% for further reaction at later ages was observed by XRD results. Moreover, combined use of silica fume and lime-water ensures a high alkaline media around steel bars from the moment of ingredients mixing as long as later ages despite of pozzolanic reaction that was identified from results of chloride attack.

Effect of silica fume on compressive strength of oil-polluted concrete in different marine environments

Science.gov (United States)

Shahrabadi, Hamid; Sayareh, Sina; Sarkardeh, Hamed

2017-12-01

In the present research, effect of silica fume as an additive and oil polluted sands as aggregates on compressive strength of concrete were investigated experimentally. The amount of oil in the designed mixtures was assumed to be constant and equal to 2% of the sand weight. Silica fume accounting for 10%, 15% and 20% of the weight is added to the designed mixture. After preparation and curing, concrete specimens were placed into the three different conditions: fresh, brackish and saltwater environments (submerged in fresh water, alternation of exposed in air & submerged in sea water and submerged in sea water). The result of compressive strength tests shows that the compressive strength of the specimens consisting of silica fume increases significantly in comparison with the control specimens in all three environments. The compressive strength of the concrete with 15% silica fume content was about 30% to 50% higher than that of control specimens in all tested environments under the condition of using polluted aggregates in the designed mixture.

Effect of temperature on physical and mechanical properties of concrete containing silica fume

International Nuclear Information System (INIS)

Saad, M.; Hanna, G.B.; Abo-El-Enein, S.A.; Kotkata, M.F.

1996-01-01

Heat-resistant materials are usually used for structural purposes. The need for such building materials is particularly important in the chemical and metallurgical industries and for the thermal shieldings of nuclear power plants. Thus the effect of high temperatures on physical and mechanical properties of concrete was investigated. In this study ordinary Portland cement has been partially replaced by ratios of silica fume. The heat treatment temperature varied from 100 to 600 C by increments of 100 C for three hours without any load. Concrete specimens were treated at each temperature level. The specimens were heated under the same condition for each temperature level. Comparison between physical and mechanical properties during heat treatment were investigated. All specimens were moist-cured for 28 days after casting. Tests were carried out on specimens cooled slowly to room temperature after heating. Results of this investigation indicated that the replacement of ordinary Portland cement by 10% silica fume by weight improved the compressive strength by about 64.6%, but replacement of ordinary Portland cement by silica fume by ratios 20 and 30% improved the compressive strength by only 28% at 600 C. This could be attributed to the additional tobermorite gel (CSH phase) which formed due to the reaction of silica fume with Ca(OH) 2

Influence of Silica Fume Addition in the Long-Term Performance of Sustainable Cement Grouts for Micropiles Exposed to a Sulphate Aggressive Medium

Directory of Open Access Journals (Sweden)

José Marcos Ortega

2017-08-01

Full Text Available At present, sustainability is of major importance in the cement industry, and the use of additions such as silica fume as clinker replacement contributes towards that goal. Special foundations, and particularly micropiles, are one of the most suitable areas for the use of sustainable cements. The aim of this research is to analyse the effects in the very long-term (for 600 days produced by sulphate attack in the microstructure of grouts for micropiles in which OPC (ordinary Portland cement has been replaced by 5% and 10% silica fume. This line of study is building on a previous work, where these effects were studied in slag and fly ash grouts. Grouts made using a commercial sulphate-resisting Portland cement were also studied. The non-destructive impedance spectroscopy technique, mercury intrusion porosimetry, and Wenner resistivity testing were used. Mass variation and the compressive strength have also been analysed. Apparently, impedance spectroscopy is the most suitable technique for studying sulphate attack development. According to the results obtained, grouts for micropiles with a content of silica fume up to 10% and exposed to an aggressive sulphate medium, have a similar or even better behaviour in the very long-term, compared to grouts prepared using sulphate-resisting Portland cement.

Effect of silica fume on reaction products of uranium (VI) with portland cement

International Nuclear Information System (INIS)

Tan Hongbin; Shaanxi Univ. of Technology, Hanzhong; Li Yuxiang

2005-01-01

Simulation of radioactive waste of U(VI) by uranyl nitrate and the effects of different additive quantities (12%, 20%, 30%, 35%, 40%) of silica fume on the products of U(VI) with Portland cement were studied at a hydrothermal condition of 180 degree C for a duration of one week. The X-ray powder diffraction examination results showed that the calcium uranate would be transformed into uranophane when the cement contained 30% silica fume. (authors)

PEMANFAATAN LIMBAH SERBUK MARMER PADA BETON SEBAGAI BAHAN PENGGANTI SEBAGIAN SEMEN DENGAN VARIASI PENGGUNAAN SILICA FUME

OpenAIRE

Agil Fitri Handayani; Agoes Soehardjono M.D.; Achfas Zacoeb

2015-01-01

The Utilization of Marble Powder Waste in Concrete Ma­­­­­­­­terials as a Partial Material Substitution of Cement  with the Variation Use of Silica Fume. The purpose of this study was to determine the effect of marble powder and silica fume on the mechanical pro­per­ties of concrete. This study used an experimental design using 16 group of testing materials with variety types of mixtures between marble powder and silica fume 0.00; 5.00; 10.00; and 15.00%. The wa­ter-cement ratio was 0.50 and ...

Enhancing the performance of green solid-state electric double-layer capacitor incorporated with fumed silica nanoparticles

Science.gov (United States)

Chong, Mee Yoke; Numan, Arshid; Liew, Chiam-Wen; Ng, H. M.; Ramesh, K.; Ramesh, S.

2018-06-01

Solid polymer electrolyte (SPE) based on fumed silica nanoparticles as nanofillers, hydroxylethyl cellulose (HEC) as host polymer, magnesium trifluoromethanesulfonate salt and 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ionic liquid is prepared by solution casting technique. The ionic conductivity, interactions of adsorbed ions on the host polymer, structural crystallinity and thermal stability are evaluated by electrochemical impedance spectroscopy (EIS), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and thermogravimetric analysis (TGA), respectively. Ionic conductivity studies at room temperature reveals that the SPE with 2 wt. % of fumed silica nanoparticles gives the highest conductivity compared to its counterpart. The XRD and FTIR studies confirm the dissolution of salt, ionic liquid and successful incorporation of fumed silica nanoparticles with host polymer. In order to examine the performance of SPEs, electric double-layer capacitor (EDLC) are fabricated by using activated carbon electrodes. EDLC studies demonstrate that SPE incorporated with 2 wt. % fumed silica nanoparticles gives high specific capacitance (25.0 F/g) at a scan rate of 5 mV/s compared to SPE without fumed silica. Additionally, it is able to withstand 71.3% of capacitance from its initial capacitance value over 1600 cycles at a current density of 0.4 A/g.

Mass spectrometric investigation of synthetic glycoside of muramyl dipeptide immobilized on fumed silica surface

Energy Technology Data Exchange (ETDEWEB)

Kulik, Tetiana V., E-mail: tanyakulyk@gala.net [O.O. Chuiko Institute of Surface Chemistry, National Academy of Sciences of Ukraine, 17 Generala Naumova Str., Kyiv 03164 (Ukraine); Azizova, Liana R., E-mail: liana_azizova@ukr.net [O.O. Chuiko Institute of Surface Chemistry, National Academy of Sciences of Ukraine, 17 Generala Naumova Str., Kyiv 03164 (Ukraine); Palyanytsya, Borys B. [O.O. Chuiko Institute of Surface Chemistry, National Academy of Sciences of Ukraine, 17 Generala Naumova Str., Kyiv 03164 (Ukraine); Zemlyakov, Alexander E.; Tsikalova, Victoria N. [Vernadsky Tauric National University, pr. Akademika Vernadskogo 4, Simferopol, 95007 (Ukraine)

2010-05-25

N-Acetylmuramyl-L-alanyl-D-isoglutamine or muramyl dipeptide is a cleavage product of peptidoglycan by lysozyme. This study explored the use of the temperature-programmed desorption mass spectrometry (TPDMS) in analysis of glycoside of muramyl dipeptide: O-{l_brace}(4-tert-butylcyclohexyl)-2-acetamido-2, 3-dideoxy-{beta}-D-glucopyranoside-3-yl{r_brace}-D-lactoyl-L-alanyl-D-isoglutamine (MDP) on the surface of fumed silica. Stages of pyrolysis of MDP in condensed state and on the silica surface have been determined. Three stages have been clear identified under pyrolysis of MDP on the silica surface. Kinetic parameters of thermal reactions on the fumed silica surface and in the condensed state have been calculated.

Upgrading offshore pipelines concrete coated by silica fume additive against aggressive mechanical laying

Directory of Open Access Journals (Sweden)

M.I. Abdou

2016-06-01

Full Text Available Studies have been carried out to investigate the possibility of utilizing a broad range of micro-silica partial additions with cement in the production of concrete coating. This study investigated the strength properties and permeability of micro-silica concrete to achieve resistance toward concrete cracking and damage during laying. The chemical composition of micro-silica (silica fume was determined, and has been conducted on concrete mixes with additions of 3 up to 25% by weight of cement in concrete. Properties of hardened concrete such as compressive strength, flexural strength, and permeability have been assessed and analyzed. Cubic specimens and beams were produced and cured in a curing tank for 7 and 28 days. Testing results have shown that additions of silica fume to cement between 5% and 7%, which acts as a filler and cementations material, developed high flexural and compressive strength with reduction of permeability.

Performance of soft clay stabilized with sand columns treated by silica fume

Directory of Open Access Journals (Sweden)

Samueel Zeena

2018-01-01

Full Text Available In many road construction projects, if weak soil exists, then uncontrollable settlement and critical load carrying capacity are major difficult problems to the safety and serviceability of roads in these areas. Thus ground improvement is essential to achieve the required level of performance. The paper presents results of the tests of four categories. First category was performed on saturated soft bed of clay without any treatment, the second category shed light on the improvement achieved in loading carrying capacity and settlement as a result of reinforcing with conventional sand columns at area replacement ratio = 0.196. The third set investigates the bed reinforced by sand columns stabilized with dry silica fume at different percentages (3, 5 and 7% and the fourth set investigates the behavior of sand columns treated with slurry silica fume at two percentages (10 and 12%. All sand columns models were constructed at (R.D= 60%. Model tests were performed on bed of saturated soil prepared at undrained shear strength between 16-20 kPa for all models. For all cases, the model test was loaded gradually by stress increments up to failure. Stress deformation measurements are recorded and analyzed in terms of bearing improvement ratio and settlement reduction ratio. Optimum results were indicated from soil treated with sand columns stabilized with 7% dry silica fume at medium state reflecting the highest bearing improvement ratio (3.04 and the settlement reduction ratio (0.09 after 7 days curing. While soil treated with sand columns stabilized with 10% slurry silica fume provided higher bearing improvement ratio 3.13 with lower settlement reduction ratio of 0.57 after 7-days curing.

Effectiveness of amorphous silica encapsulation technology on welding fume particles and its impact on mechanical properties of welds

International Nuclear Information System (INIS)

Wang, Jun; Wu, Chang-Yu; Franke, Gene

2014-01-01

Highlights: • A novel welding shielding gas containing a silica precursor. • Up to 76% of the welding fume particles encapsulated in an amorphous silica layer. • No statistical difference between different types of welds in mechanical tests. • Can potentially reduce the toxicity of welding fume particles. - Abstract: Stainless steel welding generates nano-sized fume particles containing toxic metals which may cause serious health effects upon inhalation. The objective of this study was to investigate the effectiveness of an amorphous silica encapsulation (ASE) technology by evaluating its silica coating efficiency (SCE), particle morphology, and its impact on the weld’s mechanical properties. Tetramethylsilane (TMS) added to the welding shielding gas decomposed at the high-temperature arc zone to enable the silica coating. Collected welding fume particles were digested by two acid mixtures with different degrees of silica solubility, and the measured mass differences in the digests were used to determine the SCE. The SCEs were around 48–64% at the low and medium primary shielding gas flow rates. The highest SCE of 76% occurred at the high shielding gas flow rate (30 Lpm) with a TMS carrier gas flow of 0.64 Lpm. Transmission electron microscopy (TEM) images confirmed the amorphous silica layer on the welding fume particles at most gas flow rates, as well as abundant stand-alone silica particles formed at the high gas flow rate. Metallography showed that welds from the baseline and from the ASE technology were similar except for a tiny crack found in one particular weld made with the ASE technology. Tensile tests showed no statistical difference between the baseline and the ASE welds. All the above test results confirm that welding equipment retrofitted with the ASE technology has the potential to effectively address the toxicity problem of welding fume particles without affecting the mechanical properties of the welds

Effect of plasticizer and fumed silica on ionic conductivity behaviour ...

Indian Academy of Sciences (India)

behaviour of proton conducting polymer electrolytes containing different concentrations of hexafluorophosphoric acid (HPF6) in polyethylene oxide ... Polymer electrolytes; ionic conductivity; polyethylene oxide; plasticizer; fumed silica. 1. Introduction ..... is a rapid weight loss which could be due to the degradation of polymer ...

PEMANFAATAN LIMBAH SERBUK MARMER PADA BETON SEBAGAI BAHAN PENGGANTI SEBAGIAN SEMEN DENGAN VARIASI PENGGUNAAN SILICA FUME

Directory of Open Access Journals (Sweden)

Agil Fitri Handayani

2015-02-01

Full Text Available The Utilization of Marble Powder Waste in Concrete Ma­­­­­­­­terials as a Partial Material Substitution of Cement  with the Variation Use of Silica Fume. The purpose of this study was to determine the effect of marble powder and silica fume on the mechanical pro­per­ties of concrete. This study used an experimental design using 16 group of testing materials with variety types of mixtures between marble powder and silica fume 0.00; 5.00; 10.00; and 15.00%. The wa­ter-cement ratio was 0.50 and a low dosage of superplasticizer, which was 0.50%. The behavior of fresh concrete were calculated and the mechanical properties of concrete were tested on con­crete age of 28 days. The results showed the marble powder main com­position was Silicon Dioxide (SiO2 17.63% and Calcium Carbonate (CaCO3 2.73%. Mar­ble powder was more appropriate to be used as fillers than to be used as a partial substitution of ce­ment. The optimum mechanical properties of concrete was produced by the mixtures of 5.00% mar­ble powder  and 6.22% silica fume which resulted in compressive strength of 29.04 MPa.   Tujuan penelitian ini adalah untuk mengetahui pengaruh peng­gunaan ser­buk marmer dan silica fume terhadap sifat mekanik beton. Penelitian ini meng­gu­na­kan desain eksperimen dengan 16 kelompok benda uji dengan variasi ser­buk marmer dan silica fume 0,00; 5,00; 10,00; dan 15,00%. Faktor air semen di­gu­nakan 0,50 dan superplasticizer dengan dosis rendah 0,50%. Perilaku beton segar di­perhitungkan dan sifat mekanik beton diuji pada umur beton 28 hari. Hasil analisis me­nunjukkan kom­posisi utama serbuk marmer adalah Silikon Dioksida (SiO2 17,63% dan Kalsium Kar­bonat (CaCO3 2,73%. Serbuk marmer lebih tepat digunakan se­bagai bahan pe­ng­isi atau filler dari pada sebagai pengganti semen. Sifat mekanik be­ton optimum di­ha­sil­kan pada campuran serbuk marmer 5,00% dan silica fume 6,22% dengan kuat tekan be­ton yang dihasilkan  mencapai 29

Acceleration of Intended Pozzolanic Reaction under Initial Thermal Treatment for Developing Cementless Fly Ash Based Mortar

Directory of Open Access Journals (Sweden)

Yang-Hee Kwon

2017-02-01

Full Text Available Without using strong alkaline solution or ordinary Portland cement, a new structural binder consisting of fly ash and hydrated lime was hardened through an intensified pozzolanic reaction. The main experimental variables are the addition of silica fume and initial thermal treatment (60 °C for 3 days. A series of experiments consisting of mechanical testing (compressive and flexural strength, modulus of elasticity, X-ray diffraction, and measurements of the heat of hydration, pore structure, and shrinkage were conducted. These tests show that this new fly ash-based mortar has a compressive strength of 15 MPa at 91 days without any silica fume addition or initial thermal treatment. The strength increased to over 50 MPa based on the acceleration of the intensified pozzolanic reaction from the silica fume addition and initial thermal treatment. This is explained by a significant synergistic effect induced by the silica fume. It intensifies the pozzolanic reaction under thermal treatment and provides a space filling effect. This improved material performance can open a new pathway to utilize the industrial by-product of fly ash in cementless construction materials.

The Effect of Aging and Silanization on the Mechanical Properties of Fumed Silica-based Dental Composite

Directory of Open Access Journals (Sweden)

Khaje S

2015-12-01

Full Text Available Statement of Problem: Mechanical strength and durability of dental composites are the main topics studied in this field of science today. This study examined fumed silica-based composite as a strong and durable restorative material through flexural and cycling test methods. Objectives: The purpose of this study was to evaluate the effect of silanization, ageing, cycling and hybridizing on mechanical properties of fumed silica-based resin composite. Materials and Methods: Composites were made of light-cured copolymer based on Bisphenol A glycolmethacrylate (Bis-GMA and Triethylene glycoldimethacrylate (TEGDMA at proportion of 50:50 which reinforced by fumed silica filler. For each composite sample, 5 specimen bars were made using Teflon mould (2 x 2 x 25 mm3. The samples with 12 wt% fumed silica (FS were considered as a base line group. The samples were exposed to cyclic cold water (FS-CCW and hot water (FS-CHW. The effect of silanization and adding more filler was studied together with samples containing 12 wt% (FS-S (12, 16 wt% (FS-S (16 and 20 wt% (FS-S (20 fumed silica filler. The filler was silanized with (γ-MPS. The degree of conversion was assessed with Fourier Transform Infra-Red spectroscopy. Flexural properties were evaluated with the Three-Point Bending test. Flexural data were analyzed with Excel software. Hardness was measured with an Atomic Force Microscope (AFM. Results: The degree of conversion of the resin reached 74% within 24 hrs. Salinization allowed more filler to be wetted by resin. Addition of silanized particles from sample FS-S (12 to sample FS-S (20 improved the mechanical strength. Hybridizing fumed silica with nano-silica (FS-N had no significant effect on the strength, but nano-hardness improved greatly. Ageing and cycling had adverse effects on the strength of the sample FS. The flexural strength of FS-CHW was 72% less than FS sample. Conclusions: Sample FS-N with low diluent and filler percentage complied with the

Influence of organic solvents on interfacial water at surfaces of silica gel and partially silylated fumed silica

International Nuclear Information System (INIS)

Turov, V.V.; Gun'ko, V.M.; Tsapko, M.D.; Bogatyrev, V.M.; Skubiszewska-Zieba, J.; Leboda, R.; Ryczkowski, J.

2004-01-01

The effects of organic solvents (dimethylsulfoxide-d 6 (DMSO-d 6 ), chloroform-d, acetone-d 6 , and acetonitrile-d 3 ) on the properties of interfacial water at surfaces of silica gel Si-40 and partially silylated fumed silica A-380 were studied by means of the 1 H NMR spectroscopy with freezing-out of adsorbed water at 180 1 H NMR investigations were also analysed on the basis of the structural characteristics of silicas and quantum chemical calculations of the chemical shifts δ H and solvent effects. DMSO-d 6 and acetonitrile-d 3 are poorly miscible with water in silica gel pores in contrast to the bulk liquids. DMSO-d 6 and chloroform-d affect the structure of the interfacial water weaker than acetone-d 6 and acetonitrile-d 3 at amounts of liquids greater than the pore volume. Acetone-d 6 and acetonitrile-d 3 can displace water from pores under this condition. The chemical shift of protons in water adsorbed on silica gel is 3.5-6.5 ppm, which corresponds to the formation of two to four hydrogen bonds per molecule. Water adsorbed on partially silylated fumed silica has two 1 H NMR signals at 5 and 1.1-1.7 ppm related to different structures (droplets and small clusters) of the interfacial water

Influence of silica fume on the strength of high strength concrete

International Nuclear Information System (INIS)

Akram, T.; Memon, S.A.; Khan, S.A.

2007-01-01

HSC (High Strength Concrete) does not become evident by a sudden change in the behavior of 'ordinary strength' concrete. There is a gradual effect that becomes more noticeable when the strength level exceeds about 40-45 MPa. There cannot be a precise level of strength which defines this change in effect. The effects are on strength and workability, requiring us to take into account in our mix proportioning, the ramifications of fineness of cement on workability and of type of aggregate and aggregate/cement ratio on strength. In fact, the selection of materials becomes more critical as the concrete strength increases and that if very high strength is required (100 MPa and higher), relatively few materials may be suitable. An experimental investigation is carried out to evaluate the feasibility of producing HSC using locally available materials and to study the influence of silica fume on the strength of HSC. The main variables in this research is amount of silica fume. The parameters that are kept constant are the amount of cement equal to 580 kg/m3, dosage of HRWRA (High Range Water Reducing Admictures) equal to 4 % by weight of cementitious materials and the ratio of fine aggregate to coarse aggregate (1:2.3). Test results revealed that it is feasible to produce HSC using locally available materials. The optimum percentage of silica fume was found to be 15 % by weight of cement. (author)

Effect of silica fume on the characterization of the geopolymer materials

Science.gov (United States)

Khater, Hisham M.

2013-12-01

The influence of silica fume (SF) addition on properties of geopolymer materials produced from alkaline activation of alumino-silicates metakaolin and waste concrete produced from demolition works has been studied through the measurement of compressive strength, Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy (SEM) analysis. Alumino-silicate materials are coarse aggregate included waste concrete and fired kaolin (metakaolin) at 800°C for 3 h, both passing a sieve of 90 μm. Mix specimens containing silica fume were prepared at water/binder ratios in a range of 0.30 under water curing. The used activators are an equal mix of sodium hydroxide and silicate in the ratio of 3:3 wt.%. The control geopolymer mix is composed of metakaolin and waste concrete in an equal mix (50:50, wt.%). Waste concrete was partially replaced by silica fume by 1 to 10 wt.%. The results indicated that compressive strengths of geopolymer mixes incorporating SF increased up to 7% substitution and then decreased up to 10% but still higher than that of the control mix. Results indicated that compressive strengths of geopolymer mixes incorporating SF increases up to 7% substitution and then decreases up to 10% but still higher than the control mix, where 7% SF-digested calcium hydroxide (CH) crystals, decreased the orientation of CH crystals, reduced the crystal size of CH gathered at the interface, and improved the interface more effectively.

Upgrading offshore pipelines concrete coated by silica fume additive against aggressive mechanical laying

OpenAIRE

M.I. Abdou; Hesham Abuseda

2016-01-01

Studies have been carried out to investigate the possibility of utilizing a broad range of micro-silica partial additions with cement in the production of concrete coating. This study investigated the strength properties and permeability of micro-silica concrete to achieve resistance toward concrete cracking and damage during laying. The chemical composition of micro-silica (silica fume) was determined, and has been conducted on concrete mixes with additions of 3 up to 25% by weight of cement...

Effect of plasticizer and fumed silica on ionic conductivity behaviour

Indian Academy of Sciences (India)

The effect of addition of propylene carbonate (PC) and nano-sized fumed silica on the ionic conductivity behaviour of proton conducting polymer electrolytes containing different concentrations of hexafluorophosphoric acid (HPF6) in polyethylene oxide (PEO) has been studied. The addition of PC results in an increase in ...

Study on properties of mortar using silica fume and ground blast furnace slag. Silica fume oyobi koro slag funmatsu wo mochiita mortar no tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shiiba, H; Honda, S; Araki, A [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

1992-09-01

The effect of silica fume and ground blast furnace slag in concrete on the content of superplasticizer, and dynamic properties of hardened mortar with such admixtures were studied experimentally. Although the dependence of a flow value on the superplasticizer was dominated by kinds of superplasticizers, blast furnace slag enhanced the flow value resulting in a high fluidity. Adsorption of superplasticizers onto admixtures was dependent on kinds of superplasticizers, and adsorption onto blast furnace slag was 1.3-2 times that onto normal Portland cement (NPC). The compressive strength of mortar increased by mixing admixtures, while the bending strength was enhanced only by mixing silica fume. Mixing mortar was lower in dynamic elastic modulus than NPC mortar at the same compressive strength, and the velocity of supersonic wave in mortar was scarcely affected by mixing. 11 refs., 14 figs., 3 tabs.

Influence of organic solvents on interfacial water at surfaces of silica gel and partially silylated fumed silica

Energy Technology Data Exchange (ETDEWEB)

Turov, V.V.; Gun' ko, V.M.; Tsapko, M.D.; Bogatyrev, V.M.; Skubiszewska-Zieba, J.; Leboda, R.; Ryczkowski, J

2004-05-15

The effects of organic solvents (dimethylsulfoxide-d{sub 6} (DMSO-d{sub 6}), chloroform-d, acetone-d{sub 6}, and acetonitrile-d{sub 3}) on the properties of interfacial water at surfaces of silica gel Si-40 and partially silylated fumed silica A-380 were studied by means of the {sup 1}H NMR spectroscopy with freezing-out of adsorbed water at 180silicas and quantum chemical calculations of the chemical shifts {delta}{sub H} and solvent effects. DMSO-d{sub 6} and acetonitrile-d{sub 3} are poorly miscible with water in silica gel pores in contrast to the bulk liquids. DMSO-d{sub 6} and chloroform-d affect the structure of the interfacial water weaker than acetone-d{sub 6} and acetonitrile-d{sub 3} at amounts of liquids greater than the pore volume. Acetone-d{sub 6} and acetonitrile-d{sub 3} can displace water from pores under this condition. The chemical shift of protons in water adsorbed on silica gel is 3.5-6.5 ppm, which corresponds to the formation of two to four hydrogen bonds per molecule. Water adsorbed on partially silylated fumed silica has two {sup 1}H NMR signals at 5 and 1.1-1.7 ppm related to different structures (droplets and small clusters) of the interfacial water.

Effect of silica fume addition on the PGNAA measurement of chlorine in concrete

International Nuclear Information System (INIS)

Naqvi, A.A.; Maslehuddin, M.; Garwan, M.A.; Nagadi, M.M.; Al-Amoudi, O.S.B.; Raashid, M.; Khateeb-ur-Rehman

2010-01-01

Pozzolanic materials, such as fly ash (FA), silica fume (SF), and blast furnace slag (BFS) are added to Portland cement in concrete to prevent reinforcement steel corrosion in concrete. Further preventive measure against reinforcement steel corrosion require monitoring of chloride salts concentration in concrete using non-destructive techniques, such as the prompt gamma-ray neutron activation analysis (PGNAA) technique. Due to interferences between gamma-rays from chlorine and calcium in PGNAA technique, detection limit of chlorine in concrete strongly depends upon calcium concentration in concrete. SF mainly contains silica and its addition to cement concrete reduces overall concentration of calcium in concrete. This may result in an improvement in detection limit of chlorine in SF-based concrete in PGNAA studies. Particularly for chlorine detection using 6.11 and 6.62 MeV prompt gamma-rays that strongly interfere with 6.42 MeV prompt gamma-rays from calcium. In this study, SF was added to Portland cement to prevent concrete reinforcement steel from corrosion. The chlorine concentration in SF cement concrete specimens containing 0.2-3.0 wt% chlorine was measured through yield of 1.16, 1.95, 6.11, 6.62, 7.41, 7.79, and 8.58 MeV chlorine gamma-rays using PGNAA technique. An excellent agreement was noted between the experimental yield of the prompt gamma-rays and the gamma-ray yield calculated through the Monte Carlo simulations. Further the minimum detectable concentration (MDC) of chlorine in SF cement concrete was calculated and compared with the MDC values of chlorine in plain concrete and concrete mixed with fly ash cement. The MDC of chlorine in SF-based concrete through 6.11 MeV, and 6.62 MeV chlorine gamma-rays was found to be improved as compared to those in plain concrete and concrete mixed with fly ash cement.

Effect of silica fume addition on the PGNAA measurement of chlorine in concrete

Energy Technology Data Exchange (ETDEWEB)

Naqvi, A.A. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)], E-mail: aanaqvi@kfupm.edu.sa; Maslehuddin, M. [Center for Engineering Research, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Garwan, M.A. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Nagadi, M.M. [Center for Engineering Research, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Al-Amoudi, O.S.B. [Department of Civil Engineering, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Raashid, M.; Khateeb-ur-Rehman [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2010-03-15

Pozzolanic materials, such as fly ash (FA), silica fume (SF), and blast furnace slag (BFS) are added to Portland cement in concrete to prevent reinforcement steel corrosion in concrete. Further preventive measure against reinforcement steel corrosion require monitoring of chloride salts concentration in concrete using non-destructive techniques, such as the prompt gamma-ray neutron activation analysis (PGNAA) technique. Due to interferences between gamma-rays from chlorine and calcium in PGNAA technique, detection limit of chlorine in concrete strongly depends upon calcium concentration in concrete. SF mainly contains silica and its addition to cement concrete reduces overall concentration of calcium in concrete. This may result in an improvement in detection limit of chlorine in SF-based concrete in PGNAA studies. Particularly for chlorine detection using 6.11 and 6.62 MeV prompt gamma-rays that strongly interfere with 6.42 MeV prompt gamma-rays from calcium. In this study, SF was added to Portland cement to prevent concrete reinforcement steel from corrosion. The chlorine concentration in SF cement concrete specimens containing 0.2-3.0 wt% chlorine was measured through yield of 1.16, 1.95, 6.11, 6.62, 7.41, 7.79, and 8.58 MeV chlorine gamma-rays using PGNAA technique. An excellent agreement was noted between the experimental yield of the prompt gamma-rays and the gamma-ray yield calculated through the Monte Carlo simulations. Further the minimum detectable concentration (MDC) of chlorine in SF cement concrete was calculated and compared with the MDC values of chlorine in plain concrete and concrete mixed with fly ash cement. The MDC of chlorine in SF-based concrete through 6.11 MeV, and 6.62 MeV chlorine gamma-rays was found to be improved as compared to those in plain concrete and concrete mixed with fly ash cement.

Effect of Silica Fume on two-stage Concrete Strength

Science.gov (United States)

Abdelgader, H. S.; El-Baden, A. S.

2015-11-01

Two-stage concrete (TSC) is an innovative concrete that does not require vibration for placing and compaction. TSC is a simple concept; it is made using the same basic constituents as traditional concrete: cement, coarse aggregate, sand and water as well as mineral and chemical admixtures. As its name suggests, it is produced through a two-stage process. Firstly washed coarse aggregate is placed into the formwork in-situ. Later a specifically designed self compacting grout is introduced into the form from the lowest point under gravity pressure to fill the voids, cementing the aggregate into a monolith. The hardened concrete is dense, homogeneous and has in general improved engineering properties and durability. This paper presents the results from a research work attempt to study the effect of silica fume (SF) and superplasticizers admixtures (SP) on compressive and tensile strength of TSC using various combinations of water to cement ratio (w/c) and cement to sand ratio (c/s). Thirty six concrete mixes with different grout constituents were tested. From each mix twenty four standard cylinder samples of size (150mm×300mm) of concrete containing crushed aggregate were produced. The tested samples were made from combinations of w/c equal to: 0.45, 0.55 and 0.85, and three c/s of values: 0.5, 1 and 1.5. Silica fume was added at a dosage of 6% of weight of cement, while superplasticizer was added at a dosage of 2% of cement weight. Results indicated that both tensile and compressive strength of TSC can be statistically derived as a function of w/c and c/s with good correlation coefficients. The basic principle of traditional concrete, which says that an increase in water/cement ratio will lead to a reduction in compressive strength, was shown to hold true for TSC specimens tested. Using a combination of both silica fume and superplasticisers caused a significant increase in strength relative to control mixes.

Gel/Space Ratio Evolution in Ternary Composite System Consisting of Portland Cement, Silica Fume, and Fly Ash.

Science.gov (United States)

Wu, Mengxue; Li, Chen; Yao, Wu

2017-01-11

In cement-based pastes, the relationship between the complex phase assemblage and mechanical properties is usually described by the "gel/space ratio" descriptor. The gel/space ratio is defined as the volume ratio of the gel to the available space in the composite system, and it has been widely studied in the cement unary system. This work determines the gel/space ratio in the cement-silica fume-fly ash ternary system (C-SF-FA system) by measuring the reaction degrees of the cement, SF, and FA. The effects that the supplementary cementitious material (SCM) replacements exert on the evolution of the gel/space ratio are discussed both theoretically and practically. The relationship between the gel/space ratio and compressive strength is then explored, and the relationship disparities for different mix proportions are analyzed in detail. The results demonstrate that the SCM replacements promote the gel/space ratio evolution only when the SCM reaction degree is higher than a certain value, which is calculated and defined as the critical reaction degree (CRD). The effects of the SCM replacements can be predicted based on the CRD, and the theological predictions agree with the test results quite well. At low gel/space ratios, disparities in the relationship between the gel/space ratio and the compressive strength are caused by porosity, which has also been studied in cement unary systems. The ratio of cement-produced gel to SCM-produced gel ( G C to G S C M ratio) is introduced for use in analyzing high gel/space ratios, in which it plays a major role in creating relationship disparities.

Gel/Space Ratio Evolution in Ternary Composite System Consisting of Portland Cement, Silica Fume, and Fly Ash

Directory of Open Access Journals (Sweden)

Mengxue Wu

2017-01-01

Full Text Available In cement-based pastes, the relationship between the complex phase assemblage and mechanical properties is usually described by the “gel/space ratio” descriptor. The gel/space ratio is defined as the volume ratio of the gel to the available space in the composite system, and it has been widely studied in the cement unary system. This work determines the gel/space ratio in the cement-silica fume-fly ash ternary system (C-SF-FA system by measuring the reaction degrees of the cement, SF, and FA. The effects that the supplementary cementitious material (SCM replacements exert on the evolution of the gel/space ratio are discussed both theoretically and practically. The relationship between the gel/space ratio and compressive strength is then explored, and the relationship disparities for different mix proportions are analyzed in detail. The results demonstrate that the SCM replacements promote the gel/space ratio evolution only when the SCM reaction degree is higher than a certain value, which is calculated and defined as the critical reaction degree (CRD. The effects of the SCM replacements can be predicted based on the CRD, and the theological predictions agree with the test results quite well. At low gel/space ratios, disparities in the relationship between the gel/space ratio and the compressive strength are caused by porosity, which has also been studied in cement unary systems. The ratio of cement-produced gel to SCM-produced gel ( G C to G S C M ratio is introduced for use in analyzing high gel/space ratios, in which it plays a major role in creating relationship disparities.

Controversial effects of fumed silica on the curing and thermomechanical properties of epoxy composites

Directory of Open Access Journals (Sweden)

2010-06-01

Full Text Available The effect of fumed silica on the curing of a trimethylolpropane epoxy resin was investigated by thermal analysis methods like Differential Scanning Calorimetry (DSC, and Dynamic Mechanical Analysis (DMA. The fumed silica used here is a by-product of the silicon and ferrosilicon industry, consisting of micro and nanosized particles. Both the curing reaction and the properties of the obtained composites were affected by the filler content. Different trends were observed for filler contents above and below the 30 wt%. Up to 30 wt%, the behaviour can be explained as a predominantly agglomeration effect. For 30 wt% and higher filler contents, single particles seem to play a more important role.

Properties of silica fume procured from natural diatomite and its usage in the production of vacuum insulation panels

OpenAIRE

V.P. Selyaev; V.A. Neverov; O.G. Mashtaev; A.V. Kolotushkin

2013-01-01

The article shows the results of the research of silica fume particles procured from diatomite from Atemar deposit by means of separating silicic acid from colloidal dissolved state into the sediment. The objective of the work was to define thermal-physical and structural characteristics of the silica fume. The research included IR-spectrometry, granulometry, thermal gravimetric analysis, X-ray structural analysis, optical microscopy, and small angle X-Ray scattering. As a result of the resea...

Utilizing waste materials to enhance mechanical and durability characteristics of concrete incorporated with silica fume

Directory of Open Access Journals (Sweden)

Hamza Ali

2017-01-01

Full Text Available Construction and demolition wastes are increasing significantly due to augmented boom of modern construction. Although the partial cement replacement materials do promote the idea of sustainable construction, the use of construction and demolition waste can also be considered to be viable option to advance the sustainability in modern construction practices. This paper investigates the use of industrial waste materials namely marble dust and crushed bricks as replacement of natural fine aggregates along with the use of silica fume as a partial cement replacement on the mechanical properties and durability characteristics of concrete. Partial replacement levels of waste materials were 10 and 20 percent by volume while the partial replacement level of silica fume was kept to 20 percent at all concrete samples. The results reported in this paper show that the use of marble dust as a replacement material to the natural fine aggregates resulted in an increase in the mechanical properties of concrete. However, the use of crushed bricks did not substantially contribute in the development of strength. Water permeability of concrete incorporated with both silica fume and waste materials (marble dust and crushed bricks decreased significantly. The decrease in water permeability of concrete was attributed to the pozzolanic reaction of silica fume with calcium hydroxide of cement and the filler effect of the waste materials of marble dust and crushed bricks. The use of waste materials also enhance the freeze and thaw resistance of concrete. Authors strongly suggest that the pozzolanic reaction and the development of the microstructure of the concrete through the use of waste materials are largely responsible from the advances in the durability of concrete.

Compresive Strength for FRC Member using Silica Fume

OpenAIRE

R.M.Damgir,; Y.M.Ghugal

2011-01-01

The compressive strength of concrete was obtained by conducting tests on standard cubes of size 150X 150X150 mm size with fibers 0 to 5% with an increment of 0.5% and Silica Fume of 5%.The compressivestrength was determined by carrying out compressive test by using UTM. Slump loss increases with increase in Fiber Volume Crack Width reduces as percentage Fiber Volume increases and Crack width varying between 0.75 to 1.30 mm for 28 days concrete strength. Toughness of concrete member increases ...

Cycling of lithium/metal oxide cells using composite electrolytes containing fumed silicas

International Nuclear Information System (INIS)

Zhou Jian; Fedkiw, Peter S.

2003-01-01

The effect on cycle capacity is reported of cathode material (metal oxide, carbon, and current collector) in lithium/metal oxide cells cycled with fumed silica-based composite electrolytes. Three types of electrolytes are compared: filler-free electrolyte consisting of methyl-terminated poly(ethylene glycol) oligomer (PEGdm, M w =250)+lithium bis(trifluromethylsufonyl)imide (LiTFSI) (Li:O=1:20), and two composite systems of the above baseline liquid electrolyte containing 10-wt% A200 (hydrophilic fumed silica) or R805 (hydrophobic fumed silica with octyl surface group). The composite electrolytes are solid-like gels. Three cathode active materials (LiCoO 2 , V 6 O 13 , and Li x MnO 2 ), four conducting carbons (graphite Timrex [reg] SFG 15, SFG 44, carbon black Vulcan XC72R, and Ketjenblack EC-600JD), and three current collector materials (Al, Ni, and carbon fiber) were studied. Cells with composite electrolytes show higher capacity, reduced capacity fade, and less cell polarization than those with filler-free electrolyte. Among the three active materials studied, V 6 O 13 cathodes deliver the highest capacity and Li x MnO 2 cathodes render the best capacity retention. Discharge capacity of Li/LiCoO 2 cells is affected greatly by cathode carbon type, and the capacity decreases in the order of Ketjenblack>SFG 15>SFG 44>Vulcan. Current collector material also plays a significant role in cell cycling performance. Lithium/vanadium oxide (V 6 O 13 ) cells deliver increased capacity using Ni foil and carbon fiber current collectors in comparison to an Al foil current collector

The effects of silica fume and hydrated lime on the strength development and durability characteristics of concrete under hot water curing condition

Directory of Open Access Journals (Sweden)

Hamza Ali

2017-01-01

Full Text Available Sustainability is considered to be highly important for preserving continued industrial growth and human development. Concrete, being the world’s largest manufacturing material comprises cement as an essential binding component for strength development. However, excessive production of cement due to high degree of construction practices around the world frames cement as a leading pollutant of releasing significant amounts of CO2 in the atmosphere. To overcome this environmental degradation, silica fume and hydrated lime are used as partial replacements to cement. This paper begins with the examination of the partial replacement levels of hydrated lime and silica fume in concrete and their influence on the mechanical properties and durability characteristics of concrete. The effect of hot water curing on concrete incorporated with both silica fume and hydrated lime is also investigated in this paper. The results reported in this paper show that the use of silica fume as a partial replacement material improved both the mechanical properties and durability characteristics of concrete due to the formation of calcium silica hydrate crystals through the pozzolanic reaction. Although the hydrated lime did not significantly contribute in the development of strength, its presence enhanced the durability of concrete especially at long-term. The results also showed that hot water curing enhanced the strength development of concrete incorporated with silica fume due to the accelerated rate of both the hydration and pozzolanic reaction that takes place between silica fume and calcium hydroxide of the cement matrix particularly at early times. The results reported in this paper have significant contribution in the development of sustainable concrete. The paper does not only address the use of alternative binders as a partial replacement material in concrete but also suggest proper curing conditions for the proposed replacement materials. These practices

Some engineering properties of heavy concrete added silica fume

International Nuclear Information System (INIS)

Akkaş, Ayşe; Başyiğit, Celalettin; Esen, Serap

2013-01-01

Many different types of building materials have been used in building construction for years. Heavy concretes can be used as a building material for critical building as it can contain a mixture of many heavy elements. The barite itself for radiation shielding can be used and also in concrete to produce the workable concrete with a maximum density and adequate structural strength. In this study, some engineering properties like compressive strength, elasticity modules and flexure strength of heavy concretes’ added Silica fume have been investigated

Effects of curing type, silica fume fineness, and fiber length on the mechanical properties and impact resistance of UHPFRC

Directory of Open Access Journals (Sweden)

Hasan Şahan Arel

Full Text Available The effects of silica fume fineness and fiber aspect ratio on the compressive strength and impact resistance of ultra high-performance fiber-reinforced concrete (UHPFRC are investigated experimentally. To this end, UHPFRC mixtures are manufactured by combining silica fumes with different fineness (specific surface areas: 17,200, 20,000, and 27,600 m2/kg and hooked-end steel fibers with various aspect ratios (lengths: 8, 13, and 16 mm. The samples are subjected to standard curing, steam curing, and hot-water curing. Compressive strength tests are conducted after 7-, 28-, 56-, and 90-day curing periods, and an impact resistance experiment is performed after the 90th day. A steam-cured mixture of silica fumes with a specific surface area of 27,600 m2/kg and 16-mm-long fibers produce better results than the other mixtures in terms of mechanical properties. Moreover, impact resistance increases with the fiber aspect ratio. Keywords: Curing, Fineness, UHPFRC, Mechanical properties, Fiber

Fumed Silica Nanoparticles Incorporated in Quaternized Poly(Vinyl Alcohol Nanocomposite Membrane for Enhanced Power Densities in Direct Alcohol Alkaline Fuel Cells

Directory of Open Access Journals (Sweden)

Selvaraj Rajesh Kumar

2015-12-01

Full Text Available A nanocomposite polymer membrane based on quaternized poly(vinyl alcohol/fumed silica (QPVA/FS was prepared via a quaternization process and solution casting method. The physico-chemical properties of the QPVA/FS membrane were investigated. Its high ionic conductivity was found to depend greatly on the concentration of fumed silica in the QPVA matrix. A maximum conductivity of 3.50 × 10−2 S/cm was obtained for QPVA/5%FS at 60 °C when it was doped with 6 M KOH. The permeabilities of methanol and ethanol were reduced with increasing fumed silica content. Cell voltage and peak power density were analyzed as functions of fumed silica concentration, temperature, methanol and ethanol concentrations. A maximum power density of 96.8 mW/cm2 was achieved with QPVA/5%FS electrolyte using 2 M methanol + 6 M KOH as fuel at 80 °C. A peak power density of 79 mW/cm2 was obtained using the QPVA/5%FS electrolyte with 3 M ethanol + 5 M KOH as fuel. The resulting peak power densities are higher than the majority of published reports. The results confirm that QPVA/FS exhibits promise as a future polymeric electrolyte for use in direct alkaline alcoholic fuel cells.

Chloride accelerated test: influence of silica fume, water/binder ratio and concrete cover thickness

Directory of Open Access Journals (Sweden)

E. Pereira

Full Text Available In developed countries like the UK, France, Italy and Germany, it is estimated that spending on maintenance and repair is practically the same as investment in new constructions. Therefore, this paper aims to study different ways of interfering in the corrosion kinetic using an accelerated corrosion test - CAIM, that simulates the chloride attack. The three variables are: concrete cover thickness, use of silica fume and the water/binder ratio. It was found, by analysis of variance of the weight loss of the steel bars and chloride content in the concrete cover thickness, there is significant influence of the three variables. Also, the results indicate that the addition of silica fume is the path to improve the corrosion protection of low water/binder ratio concretes (like 0.4 and elevation of the concrete cover thickness is the most effective solution to increase protection of high water/binder ratio concrete (above 0.5.

Fresh and some mechanical properties of sifcon containing silica fume

Directory of Open Access Journals (Sweden)

Salih Shakir

2018-01-01

Full Text Available Slurry infiltrated fiber concrete (SIFCON is one of the recently developed construction material. SIFCON could be considered as a special type of fiber concrete with high fiber content. The matrix of SIFCON consists of flowing cement mortar or cement slurry. SIFCON has a very good potential for application in area where resistance to impact and high ductility are needed especially in designing the seismic retrofit, in the structures under impact and explosive effects and repair of structural reinforced concrete element. The main objective of this paper is to determine the effect of steel fiber content and silica fume (SF cement replacement on the mechanical properties of SIFCON concrete. The percentage of SF replacement was 10% by weight of cement in SIFCON slurry, and three different volume fractions of hooked ended steel fiber (6, 8.5, and 11 % were used. The tested properties of SIFCON were compressive strength and splitting tensile strength which were carried out on standard size of cubes and cylinders respectively at the age of 7and 28 days. It was observed that the mechanical properties of SIFCON were affected in a positive manner by using silica fume as a partial replacement of cement and by adding steel fiber reinforcement in different percentages. The compressive and splitting tensile strength up to 83.7 MPa and 17.3MPa, respectively were obtained at the age of 28 days.

Improvement in ionic conductivity of self-supported P(MMA-AN-VAc) gel electrolyte by fumed silica for lithium ion batteries

International Nuclear Information System (INIS)

Liao Youhao; Rao Mumin; Li Weishan; Tan Chunlin; Yi Jin; Chen Lang

2009-01-01

Fumed silica was used as a dopant in the preparation of poly(methyl methacrylate-acrylonitrile-vinyl acetate) (P(MMA-AN-VAc)) to improve the ionic conductivity of the P(MMA-AN-VAc)-based gel polymer electrolyte (GPE). The performance of the P(MMA-AN-VAc) membrane and its GPE for lithium ion battery use were studied by XRD, SEM, TGA, LSV, CA, EIS, and charge/discharge test. It is found that the doping of fumed silica in the P(MMA-AN-VAc) changes the membrane from semi-crystal to amorphous state and the pore structure of the membrane. By the doping of 10 wt.% fumed silica in the membrane, the porosity of the membrane increases with the pore dispersed more uniformly and interconnected and having higher electrolyte uptake, resulting in the improvement in ionic conductivity of the GPE from 3.48 x 10 -3 to 5.13 x 10 -3 S cm -1 at ambient temperature. On the other hand, the thermal stability of the membrane, the electrochemical stability of the GPE, and the cyclic performance of the battery are also improved.

Autogenous Deformation and Change of the Relative Humidity in Silica Fume-Modified Cement Paste

DEFF Research Database (Denmark)

Jensen, Ole mejlhede; Hansen, Per Freiesleben

1996-01-01

Even during sealed curing and at a constant temperature a hardening cement paste will deform and the relative humidity within its pores will lower. This autogenous deformation and autogenous relative humidity change may be so significant that the cement paste cracks if the deformation is restrained....... This article focuses on the influence of silica fume addition on autogenous deformation and autogenous relative humidity change. Continuous measurement of autogenous deformation and autogenous relative humidity change for more than 1 year and 1« years, respectively, was performed. The investigations show...... thatsilica fume addition markedly increases the autogenous shrinkage as well as the autogenous relative humidity change....

Investigation of compressive strength of concrete with slag and silica fu

International Nuclear Information System (INIS)

Mostofinejad, D.; Mirtalee, K.; Sadeghi, M.

2002-01-01

Without doubt, concrete has special place in construction of different types of structures, and used as one of the most important materials in construction industry. Today, with development and modernization of human knowledge in construction industry, it is possible to reach h igh performance concrete . Mechanical properties and durability of high performance concrete is quite better than that of conventional concrete. In present, the use of supplementary cementitious materials, mainly silica fume, fly ash and blast furnace slag has become increasingly common for reasons of economy and technical benefits imparted by these materials. The aim of present research is investigation and comparison compressive strength of concrete specimens due to variation of water to cementitious materials ratio (W/C M), silica fume and slag percent and their proportions as cement replacement. Furthermore, it is intended to determine best combination of these materials with cement in concrete (optimum percent) to reach to maximum compressive strength. In the current study, specimens were made in 0.5,0.4 and 0.3 W/C M ratio contained 0,20,35 and 50 percent of slag as cement replacement, where in each slag replacement percent, 0, 5, 10 and 15 percent of of silica fume were used as cement replacement. Results of the current study show that the combination effect of slag and silica fume replacement in concrete leads to the maximum compressive strength in concrete; also there are some optimum percents for replacement of slag and silica fume to cement to get the best results

Beyond waste: new sustainable fillers from fly ashes stabilization, obtained by low cost raw materials

Directory of Open Access Journals (Sweden)

N. Rodella

2016-09-01

Full Text Available A sustainable economy can be achieved only by assessing processes finalized to optimize the use of resources. Waste can be a relevant source of energy thanks to energy-from-waste processes. Concerns regarding the toxic fly ashes can be solved by transforming them into resource as recycled materials. The commitment to recycle is driven by the need to conserve natural resources, reduce imports of raw materials, save landfill space and reduce pollution. A new method to stabilize fly ash from Municipal Solid Waste Incinerator (MSWI at room temperature has been developed thanks to COSMOS-RICE LIFE+ project (www.cosmos-rice.csmt.eu. This process is based on a chemical reaction that occurs properly mixing three waste fly ashes with rice husk ash, an agricultural by-product. COSMOS inert can replace critical raw materials (i.e. silica, fluorspar, clays, bentonite, antimony and alumina as filler. Moreover the materials employed in the stabilization procedure may be not available in all areas. This paper investigates the possibility of substituting silica fume with corresponding condensed silica fume and to substitute flue-gas desulfurization (FGD residues with low-cost calcium hydroxide powder. The removal of coal fly ash was also considered. The results will be presented and a possible substitution of the materials to stabilize fly ash will be discussed.

An Accelerated Test Method of Simultaneous Carbonation and Chloride Ion Ingress: Durability of Silica Fume Concrete in Severe Environments

Directory of Open Access Journals (Sweden)

S. A. Ghahari

2016-01-01

Full Text Available The effects of simultaneous carbonation and chloride ion attack on mechanical characteristics and durability of concrete containing silica fume have been investigated through an accelerated test method. Specimens containing different amounts of silica fume were maintained in an apparatus in which carbon dioxide pressure and concentration and relative humidity were kept constant, and wetting and drying cycles in saline water were applied. Surface resistivity, sorptivity, CO2 consumption, and carbonation and chloride ion ingress depths measurements were taken. Phase change due to carbonation and chloride ion attack was monitored by XRD analysis, and microstructures and interfacial transition zones were studied by implementing SEM as well as mercury intrusion porosimetry. It was expected to have a synergistic effect in the tidal zone where simultaneous carbonation and chloride ion attack happen. However, the observed reduced surface resistivity, compared to specimens maintained in CO2 gas, could be due to the moisture that is available near the surface, hindering CO2 from penetrating into the pores of the specimens. Moreover, the porosity analysis of the specimens showed that the sample containing silica fume cured in the tidal zone had 50.1% less total porosity than the plain cement paste cured in the same condition.

Influence of silica fume on mechanical and physical properties of recycled aggregate concrete

OpenAIRE

Çakır, Özgür; Sofyanlı, Ömer Özkan

2015-01-01

Several studies related to sustainable concrete construction have encouraged development of composite binders, involving Portland cement, industrial by-products, and concrete mixes with partial replacement of natural aggregate with recycled aggregate. In this paper, the effects of incorporating silica fume (SF) in the concrete mix design to improve the quality of recycled aggregates in concrete are presented. Portland cement was replaced with SF at 0%, 5% and 10%. Specimens were manufactured ...

Abrasion Properties of Steel Fiber Reinforced Silica Fume Concrete According to Los Angeles and Water Abrasion Tests

Directory of Open Access Journals (Sweden)

Tsan-Ching CHENG

2014-12-01

Full Text Available The current study mainly investigated the influence of different tests on the abrasion resistance of concrete mixed with steel fibers and silica fume. The abrasion resistance was assessed at 28, 56 and 91 days on concretes with water-binder ratios of 0.35 and 0.55 where in some mixes silica fume was substituted by 5 % of cement by weight. Steel fibers of 0.5 % and 1.0 % of concrete volume were also added into the test concrete by replacement of coarse and fine aggregates. The results showed that concrete with higher compressive strength in Los Angeles abrasion tests also had better abrasion resistance. The inclusion of steel fibers into test concrete with a water-binder ratio of 0.35 resulted in a significant increase in compressive strength. This concrete also displayed better abrasion resistance and splitting tensile strength than reference concrete; in the test sample with a water-binder ratio of 0.55, the added steel fibers was unable to effectively produce cementation with the concrete. The inclusion of silica fume improved the abrasion resistance of concretes. In water abrasion testing, the abrasion resistance of concrete containing steel fiber was worse than that of concrete without steel fibers. In the water abrasion testing, the surface of steel fiber reinforced concrete was eroded by water and steel balls, and the impact caused the steel fibers to separate from the concrete and led to higher wear loss. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6460

Experimental and numerical investigation of form-stable dodecane/hydrophobic fumed silica composite phase change materials for cold energy storage

International Nuclear Information System (INIS)

Chen, Jiajie; Ling, Ziye; Fang, Xiaoming; Zhang, Zhengguo

2015-01-01

Highlights: • Form-stable dodecane/fumed silica composite for cold storage is prepared. • A suggesting hypothesis that explains infiltration mechanism is proposed. • The performance of the composite phase change material is investigated. • Numerical simulation of system is carried out and results fit well. - Abstract: A kind of form-stable composite phase change materials used for cold thermal energy storage is prepared by absorbing dodecane into the hydrophobic fumed silica. With relatively suitable pore diameter and hydrophobic groups, hydrophobic fumed silica is beneficial to the penetration and infiltration of dodecane and the leakage problem solving. Scanned by electron micrographs and Fourier transformation infrared, the composite phase change material is characterized to be just physical penetration. Besides, the differential scanning calorimeter and thermo gravimetric analysis reveals the high enthalpy, good thermal stability and cycling performance of this composite phase change material. What’s more, Hot-Disk thermal constants analyzer demonstrates that the composite phase change material has low thermal conductivity which is desired in cold storage application. In the experiment, a cold energy storage system is set up and the results from the experiment show that the system has excellent performance of cold storage by incorporating composite phase change material. Apart from that, the experimental data is found to have a great agreement with the numerical simulation which is carried out by using the commercial computational fluid dynamics software FLUENT.

Strength and Mechanical Properties of High Strength Cement Mortar with Silica Fume

OpenAIRE

川上, 英男; 谷, 康博

1993-01-01

Two series of tests were carried out to clarify the effects of silica fume on the strength and mechanical properties of cement mortar. The test specimens of cement mortar were prepared within the flow values between 180 mm and 240 mm which qualifies better workability of the concrete. The fiow values were attained by using superplasticizer. The specimens were tested at the age of 4 weeks. Main results of the experiments are as follows. 1. At a given cement water ratio,the larger volume of sil...

Effects of using silica fume and polycarboxylate-type superplasticizer on physical properties of cementitious grout mixtures for semiflexible pavement surfacing.

Science.gov (United States)

Koting, Suhana; Karim, Mohamed Rehan; Mahmud, Hilmi; Mashaan, Nuha S; Ibrahim, Mohd Rasdan; Katman, Herdayati; Husain, Nadiah Md

2014-01-01

Semi-flexible pavement surfacing is a composite pavement that utilizes the porous pavement structure of the flexible bituminous pavement, which is subsequently grouted with appropriate cementitious materials. This study aims to investigate the compressive strength, flexural strength, and workability performance of cementitious grout. The grout mixtures are designed to achieve high strength and maintain flow properties in order to allow the cement slurries to infiltrate easily through unfilled compacted skeletons. A paired-sample t-test was carried out to find out whether water/cement ratio, SP percentages, and use of silica fume influence the cementitious grout performance. The findings showed that the replacement of 5% silica fume with an adequate amount of superplasticizer and water/cement ratio was beneficial in improving the properties of the cementitious grout.

The effect of silica fume on early hydration of white Portland cement via fast field cycling-NMR relaxometry

Science.gov (United States)

Badea, Codruţa.; Bede, Andrea; Ardelean, Ioan

2017-12-01

Fast Field Cycling (FFC) nuclear magnetic resonance (NMR) relaxometry is used to monitor the influence introduced on the hydration process by the addition of silica fume in a cement paste mixture, prepared with white Portland cement. The FFC relaxometry technique was implemented due to its sensitivity to a wider range of molecular motions, which gives more information than other relaxometry techniques performed at a fixed frequency. This unique feature of FFC relaxometry allows better separation of the surface and bulk contributions from the global measured relaxation rate. The relaxation process is dominated by the interaction of water protons with the paramagnetic centers located on the surface of cement grains. In the frame of a two-phase exchange model, this allows the monitoring of the influence of an addition of silica fume on the evolution of surface-to-volume ratio during the early hydration stages.

A Review for Characterization of Silica Fume and Its Effects on Concrete Properties

OpenAIRE

Mohammad Panjehpour; Abang Abdullah Abang Ali; Ramazan Demirboga

2011-01-01

Mineral additions which are also known as mineral admixtures have been used in Portland cement for many years. There are two types of additions which are commonly mixed into the Portland clinker or blended directly with cement these days. They are crystalline, also known as hydraulically inactive additions and pozzolanic, which are hydraulically active additions. Silica fume is very reactive pozzolan, while it is used in concrete because of its fine particles, large surface area and high SiO2...

Effects of Using Silica Fume and Polycarboxylate-Type Superplasticizer on Physical Properties of Cementitious Grout Mixtures for Semiflexible Pavement Surfacing

Directory of Open Access Journals (Sweden)

Suhana Koting

2014-01-01

Full Text Available Semi-flexible pavement surfacing is a composite pavement that utilizes the porous pavement structure of the flexible bituminous pavement, which is subsequently grouted with appropriate cementitious materials. This study aims to investigate the compressive strength, flexural strength, and workability performance of cementitious grout. The grout mixtures are designed to achieve high strength and maintain flow properties in order to allow the cement slurries to infiltrate easily through unfilled compacted skeletons. A paired-sample t-test was carried out to find out whether water/cement ratio, SP percentages, and use of silica fume influence the cementitious grout performance. The findings showed that the replacement of 5% silica fume with an adequate amount of superplasticizer and water/cement ratio was beneficial in improving the properties of the cementitious grout.

Formulating a low-alkalinity cement for radioactive waste repositories

Energy Technology Data Exchange (ETDEWEB)

Coumes, C. Cau Dit; Courtois, S.; Leclercq, S.; Bourbon, X

2004-07-01

A multi-annual research program has been launched in January 2003 by CEA, EDF and ANDRA in order to formulate and characterize low-alkalinity and low-heat cements which would be compatible with an underground waste repository environment. Four types of bindings have been investigated: binary blends of Portland cement and silica fume or metakaolin, as well as ternary blends of Portland cement, fly ash and silica fume or metakaolin. Promising results have been obtained with a mixture comprising 37.5% Portland cement, 32.5% silica fume, and 30% fly ash: pH of water in equilibrium with fully hydrated cement is below 11. Moreover, silica fume compensates for the low reactivity of fly ash, while fly ash allows to reduce water demand, heat release, and dimensional variations of cement pastes and mortars. (authors)

Formulating a low-alkalinity cement for radioactive waste repositories

International Nuclear Information System (INIS)

Coumes, C. Cau Dit; Courtois, S.; Leclercq, S.; Bourbon, X.

2004-01-01

A multi-annual research program has been launched in January 2003 by CEA, EDF and ANDRA in order to formulate and characterize low-alkalinity and low-heat cements which would be compatible with an underground waste repository environment. Four types of bindings have been investigated: binary blends of Portland cement and silica fume or metakaolin, as well as ternary blends of Portland cement, fly ash and silica fume or metakaolin. Promising results have been obtained with a mixture comprising 37.5% Portland cement, 32.5% silica fume, and 30% fly ash: pH of water in equilibrium with fully hydrated cement is below 11. Moreover, silica fume compensates for the low reactivity of fly ash, while fly ash allows to reduce water demand, heat release, and dimensional variations of cement pastes and mortars. (authors)

Compaction and Collapse Characteristics of Dune Sand Stabilized with Lime-Silica Fume Mix

Directory of Open Access Journals (Sweden)

Mohammed Y. Fattah

2016-04-01

Full Text Available The purpose of this research is to assess the suitability of dune sands as construction materials. Moreover, such a goal is considered beneficial in determining appropriate methods for soil stabilization or ground improvement and to assessing the suitability of dune sands as subgrade layer for carrying roads and rail foundation. Dune sand samples were collected from a region in Baiji area in Salah-Aldeen governorate, North of Iraq. A grey-colored densified silica fume (SF and lime (L are used. Three percentages are used for lime (3%, 6%, and 9%, and four rates are used for silica fume (3%, 6%, 9% and 12% and the maximum percentage of silica fume is mixed with the proportions of lime. Unsoaked California Bearing Ratio (CBR on compacted dune sands treated dune sands with L-SF by mixing and cured for one day. The increasing in CBR ranged between 443 – 707% at 2.54 mm penetration and 345 – 410% at 5.08 mm penetration.     Resumen El propósito de esta investigación es evaluar el uso de arena de dunas como materiales de construcción. Además, este objetivo permite determinar los métodos apropiados para la estabilización del suelo, el mejoramiento del terreno y la evaluación de pertinencia de la arena de dunas en capas subbase para carreteras y cimientos férreos. Se recolectaron muestras de arena de dunas en el área de Baiji, del comisionado Salah-Aldeen, al norte de Irak. Se utilizó vapor de óxido de silicio (SF, en inglés, grisáceo y densificado, y óxido de calcio (L. Se utilizaron tres porcentajes para el óxido de calcio (3 %, 6 % y 9 %, y cuatro para el óxido de silicio (3 %, 6 %,  9% y 12% y el máximo porcentaje del óxido de silicio se mezcló con las proporciones de óxido de calcio. Se realizó en seco el Ensayo de Relación de Soporte de California (del inglés California Bearing Ratio, CBR en arena de dunas compactada y tratada con la mezcla L-SF curada durante un día. El incremento en el ensayo CBR osciló entre 443

Synthesis of zeolite from coal fly ashes with different silica-alumina composition

Energy Technology Data Exchange (ETDEWEB)

Miki Inada; Yukari Eguchi; Naoya Enomoto; Junichi Hojo [Kyushu University, Fukuoka (Japan). Department of Chemistry and Biochemistry, Graduate School of Engineering

2005-02-01

Coal fly ashes can be converted into zeolites by hydrothermal alkaline treatment. This study focuses on the effect of Si/Al molar ratio of the fly ash source on the type of formed zeolite, which also is affected by the alkaline condition. The fly ashes were mixed with an aqueous NaOH solution and hydrothermally treated at about 100{degree}C. Zeolite Na-P1 and/or hydroxy-sodalite appeared after the treatment. Zeolite Na-P1 predominantly formed from silica-rich fly ash at a low-NaOH concentration. The cation exchange capacity of the product with a large content of zeolite Na-P1 reached a value of 300 meq/100 g. The type of the product was controlled by addition of aerosil silica or alumina. It was found that silica addition effectively enhances the formation of zeolite Na-P1, even at a high-NaOH concentration. These results were discussed on the basis of a formation mechanism of zeolite from coal fly ash through dissolution-precipitation process. 10 refs., 6 figs., 1 tab.

Mechanical and chemical properties of polyvinyl alcohol modified cement mortar with silica fume used as matrix including radioactive waste

International Nuclear Information System (INIS)

Dakroury, A. M.

2007-01-01

This paper discussed the mechanical and chemical properties of polyvinyl alcohol - modified cement mortar with silica fume to assess the safety for disposal of radioactive waste. The modified cement mortars containing polyvinyl alcohol (PVA) in the presence of 10 % silica fume (SF) .The chemical reaction between polymer and cement - hydrated product were investigated by the Infrared Spectral Technology, Differential Thermal Analysis and X-ray diffraction. The leaching of 137Cs from a waste composite into a surrounding fluid has been studied .The results shown that PVA increases the strength and decreases the porosity. The increase in strength duo to the interaction of PVA with cement , may be forming some new compound that fill the pores or improve the bond between the cement . The pozzolanic reaction of the SF increases the calcium silicate hydrates in the hardening matrix composites. There is distinct change in the refinement of the pore structure in cement composites giving fewer capillary pores and more of the finer gel pores

Investigation of Fumed Silica/Aqueous NaCl Superdielectric Material

Directory of Open Access Journals (Sweden)

Natalie Jenkins

2016-02-01

Full Text Available A constant current charge/discharge protocol which showed fumed silica filled to the point of incipient wetness with aqueous NaCl solution to have dielectric constants >108 over the full range of dielectric thicknesses of 0.38–3.9 mm and discharge times of 0.25–>100 s was studied, making this material another example of a superdielectric. The dielectric constant was impacted by both frequency and thickness. For time to discharge greater than 10 s the dielectric constant for all thicknesses needed to be fairly constant, always >109, although trending higher with increasing thickness. At shorter discharge times the dielectric constant consistently decreased, with decreasing time to discharge. Hence, it is reasonable to suggest that for time to discharge >10 s the dielectric constant at all thicknesses will be greater than 109. This in turn implies an energy density for a 5 micron thick dielectric layer in the order of 350 J/cm3 for discharge times greater than 10 s.

Investigation of Fumed Silica/Aqueous NaCl Superdielectric Material.

Science.gov (United States)

Jenkins, Natalie; Petty, Clayton; Phillips, Jonathan

2016-02-20

A constant current charge/discharge protocol which showed fumed silica filled to the point of incipient wetness with aqueous NaCl solution to have dielectric constants >10⁸ over the full range of dielectric thicknesses of 0.38-3.9 mm and discharge times of 0.25->100 s was studied, making this material another example of a superdielectric. The dielectric constant was impacted by both frequency and thickness. For time to discharge greater than 10 s the dielectric constant for all thicknesses needed to be fairly constant, always >10⁸, although trending higher with increasing thickness. At shorter discharge times the dielectric constant consistently decreased, with decreasing time to discharge. Hence, it is reasonable to suggest that for time to discharge >10 s the dielectric constant at all thicknesses will be greater than 10⁸. This in turn implies an energy density for a 5 micron thick dielectric layer in the order of 350 J/cm³ for discharge times greater than 10 s.

Physico-mechanical properties of high performance concrete using different aggregates in presence of silica fume

Directory of Open Access Journals (Sweden)

Salah A. Abo-El-Enein

2014-04-01

Full Text Available Heavy weight high performance concrete (HPC can be used when particular properties, such as high strength and good radiation shielding are required. Such concrete, using ilmenite and hematite coarse aggregates can significantly have higher specific gravities than those of concrete made with dolomite and air-cooled slag aggregates. Four different concrete mixes with the same cement content and different w/c ratios were designed using normal dolomite aggregate, air-cooled slag by-product and two different types of iron ore aggregates. High performance concrete (grade-M60 can be achieved using superplasticizer to reduce the water/cement ratio; the effect of SF on the performance of concrete was studied by addition of 10% silica fume to the total cement content. The physico-mechanical properties of coarse aggregates and hardened concrete were studied. The results show that, Ilmenite coarse aggregate gives higher physical and mechanical properties than the other aggregates. Also, addition of 10% silica fume developed a stronger and a denser interfacial transition zone (ITZ between concrete particles and the cement matrix. Crushed air-cooled slag can be used to produce a high-strength concrete with better mechanical properties than corresponding concrete made with crushed hematite and ilmenite. Heavy density concrete made with fine aggregates of ilmenite and air-cooled slag are expected to be suitable as shielding materials to attenuate gamma rays.

Fumed and Precipitated Hydrophilic Silica Suspension Gels in Mineral Oil: Stability and Rheological Properties

Directory of Open Access Journals (Sweden)

Yoshiki Sugino

2017-08-01

Full Text Available Hydrophilic fumed silica (FS and precipitated silica (PS powders were suspended in mineral oil; increasing the silica volume fraction (φ in the suspension led to the formation of sol, pre-gel, and gel states. Gelation took place at lower φ values in the FS than the PS suspension because of the lower silanol density on the FS surface. The shear stresses and dynamic moduli of the FS and PS suspensions were measured as a function of φ. Plots of the apparent shear viscosity against shear rate depended on φ and the silica powder. The FS suspensions in the gel state exhibited shear thinning, followed by a weak shear thickening or by constant viscosity with an increasing shear rate. In contrast, the PS suspensions in the gel state showed shear thinning, irrespective of φ. The dynamic moduli of the pre-gel and gel states were dependent on the surface silanol density: at a fixed φ, the storage modulus G′ in the linear viscoelasticity region was larger for the FS than for the PS suspension. Beyond the linear region, the G′ of the PS suspensions showed strain hardening and the loss modulus G″ of the FS and PS suspensions exhibited weak strain overshoot.

The effect of limestone powder, fly ash and silica fume on the ...

Indian Academy of Sciences (India)

water content, high powder volume increases interparticle friction due to ... are cement reactivity with environment, low permeability, diffusion coefficient ... by binding Ca(OH)2 with free silica by a pozzolanic reaction forming a non-soluble CSH.

Adjustable rheology of fumed silica dispersion in urethane prepolymers: Composition-dependent sol and gel behaviors and energy-mediated shear responses

Energy Technology Data Exchange (ETDEWEB)

Zheng, Zhong, E-mail: 11329038@zju.edu.cn; Song, Yihu, E-mail: s-yh0411@zju.edu.cn; Wang, Xiang, E-mail: 11229036@zju.edu.cn; Zheng, Qiang, E-mail: zhengqiang@zju.edu.cn [MOE Key Laboratory of Macromolecule Synthesis and Functionalization, Department of Polymer Science and Engineering, Zhejiang University, Hangzhou 310027 (China)

2015-07-15

Variation of colloidal and interfacial interactions leads to a microstructural diversity in fumed silica dispersions exhibiting absolutely different sol- or gel-like rheological responses. In this study, fumed silicas with different surface areas (200–400 m{sup 2}/g) and surface characteristics (hydrophilic or hydrophobic) are dispersed into moisture-cured polyurethane. The microstructures investigated using transmission electron microscope are associated perfectly with three different rheological behaviors: (i) Sols with well-dispersed silica aggregates, (ii) weak gels with agglomerate-linked networks, and (iii) strong gels with concentrated networks of large agglomerates. Though sols and gels are well distinguished by shear thickening or sustained thinning response through steady shear flow test, it is interesting that the sols and weak gels exhibit a uniform modulus plateau-softening-hardening-softening response with increasing dynamic strain at frequency 10 rad s{sup −1} while the strong gels show a sustained softening beyond the linear regime. Furthermore, the onset of softening and hardening can be normalized: The two softening are isoenergetic at mechanical energies of 0.3 J m{sup −3} and 10 kJ m{sup −3}. On the other hand, the hardening is initiated by a critical strain of 60%. The mechanisms involved in the generation of the sol- and the gel-like dispersions and their structural evolutions during shear are thoroughly clarified in relation to the polyols, the characteristic and content of silica and the curing catalysts.

Impact of Micro Silica on the properties of High Volume Fly Ash Concrete (HVFA)

Science.gov (United States)

Sripragadeesh, R.; Ramakrishnan, K.; Pugazhmani, G.; Ramasundram, S.; Muthu, D.; Venkatasubramanian, C.

2017-07-01

In the current situation, to overcome the difficulties of feasible construction, concrete made with various mixtures of Ordinary Portland Cement (OPC) and diverse mineral admixtures, is the wise choice for engineering construction. Mineral admixtures viz. Ground Granulated Blast Furnace Slag (GGBS), Meta kaolin (MK), Fly Ash (FA) and Silica Fume (SF) etc. are used as Supplementary Cementitious Materials (SCM) in binary and ternary blend cement system to enhance the mechanical and durability properties. Investigation on the effect of different replacement levels of OPC in M25 grade with FA + SF in ternary cement blend on the strength characteristics and beam behavior was studied. The OPC was partially replaced (by weight) with different combinations of SF (5%, 10%, 15%, 20% and 25%) and FA as 50% (High Volume Fly Ash - HVFA). The amount of FA addition is kept constant at 50% for all combinations. The compressive strength and tensile strength tests on cube and cylinder specimens, at 7 and 28 days were carried out. Based on the compressive strength results, optimum mix proportion was found out and flexural behaviour was studied for the optimum mix. It was found that all the mixes (FA + SF) showed improvement in compressive strength over that of the control mix and the mix with 50% FA + 10% SF has 20% increase over the control mix. The tensile strength was also increased over the control mix. Flexural behaviour also showed a significant improvement in the mix with FA and SF over the control mix.

Pozzolanic Reactivity of Silica Fume and Ground Rice Husk Ash as Reactive Silica in a Cementitious System: A Comparative Study

Directory of Open Access Journals (Sweden)

Weiting Xu

2016-03-01

Full Text Available This study comparably assessed the pozzolanic effect of silica fume (SF and ground rice husk ash (RHA as supplementary cementing materials on the properties of blended cement pastes and concretes. A commonly commercial silica fume (SF and locally-produced rice husk ash (RHA samples with two finenesses (one with larger size than cement and the other with smaller size than cement were used in this study. Material properties of SF and RHA were experimentally characterized. Hydration and mechanical properties of cement pastes incorporating SF and RHA were determined by thermogravimetric analysis (TGA and compressive strength tests, respectively. Properties of concretes regarding workability, mechanical property, durability, and microstructure were evaluated. Results showed that, although the finely ground RHA used in this study possessed lower SiO2 content and higher particle size compared to SF, it exhibited comparable pozzolanic reactivity with SF due to the nano-scale pores on its each single particle, leading to a higher specific surface area. The optimal replacement levels of SF and RHA were 10% by weight of cement in pastes and concretes. Although addition of SF and RHA led to a significant reduction in slump for the fresh mixtures, inclusion of up to 30% of SF or 15% of ground RHA did not adversely affect the strength of concretes. At the same mix, incorporation of finely-ground RHA in cement composites provided comparable mechanical properties, hydration degree, and durability with SF blended cement composites, owing to the porous structure and high specific surface area of RHA particles. Microstructure morphology analysis of concretes explored by scanning electron microscopy (SEM further validated the strength and the durability test results.

The effect of silica fume and metakaolin on glass-fibre reinforced concrete (GRC ageing

Directory of Open Access Journals (Sweden)

Enfedaque Díaz, A.

2010-12-01

Full Text Available The deterioration of the mechanical properties of glassfibre reinforced concrete (GRC over time rules out the use of this material in load-bearing structures. While one possible solution to this problem is the addition of pozzolans or metakaolin to the cement mortar, the amounts needed to ensure GRC integrity raise its price to non-competitive levels. Experimental research has been conducted to analyze whether the addition of small amounts of silica fume or metakaolin can prevent or mitigate the ageing issue. Unfortunately, the findings indicate that the addition of small proportions of metakaolin or silica fume to GRC are ineffective in improving its long-term performance.

Para el uso del mortero de cemento reforzado con fibras de vidrio (GRC en estructuras portantes se han de solucionar los problemas de reducción de las propiedades mecánicas que aparecen con el paso del tiempo. Estos problemas pueden ser solucionados mediante la adición de puzolanas o de metacaolín, a la pasta de mortero de cemento. Sin embargo, la cantidad de metacaolín que ha de ser añadida es elevada y el precio del GRC fabricado está fuera del mercado. Se ha realizado una campaña experimental que analiza si la adición de humo de sílice o de metacaolín en proporciones reducidas consigue evitar o paliar el problema del envejecimiento, que supone un freno al uso del GRC en elementos estructurales. Desgraciadamente, los resultados experimentales muestran que proporciones bajas de metacaolín o de humo de sílice no son efectivas para reducir el problema de pérdida de propiedades mecánicas.

In vitro dentin permeability after application of Gluma® desensitizer as aqueous solution or aqueous fumed silica dispersion

Directory of Open Access Journals (Sweden)

Hiroshi Ishihata

2011-04-01

Full Text Available OBJECTIVES: To assess and to compare the effects of Gluma® Desensitizer (GDL with an experimental glutaraldehyde and HEMA containing fumed silica dispersion (GDG on dentin permeability using a chemiluminous tracer penetration test. MATERIAL AND METHODS: Twenty disc-shaped dentin specimens were dissected from extracted human third molars. The dentin specimens were mounted in a split chamber device for determination of permeability under liquid pressure using a photochemical method. Ten specimens were randomly selected and allocated to the evaluation groups Gluma® Desensitizer as aqueous solution and glutaraldehyde/HEMA as fumed silica dispersion, respectively. Dentin disc permeability was determined at two pressure levels after removal of smear with EDTA, after albumin soaking, and after application of the desensitizing agents. Two desensitizer-treated and rinsed specimens of each group were examined by scanning electron microscopy (SEM for surface remnants. RESULTS: Comparatively large standard deviations of the mean EDTA reference and albumin soaked samples permeability values refected the differences of the dentin substrates. The mean chemiluminescence values of specimen treated with GDL and GDG, respectively, were signifcantly reduced after topical application of the desensitizing agents on albumin-soaked dentin. The effects of GDL and GDG on permeability were not signifcantly different. Treated specimens showed no surface remnants after rinsing. CONCLUSIONS: The experimental desensitizer gel formulation reduced dentin permeability as effectively as the original Gluma® Desensitizer solution.

1 1 2 3 Effect of basalt, silica sand and fly ash on the mechanical ...

Indian Academy of Sciences (India)

21

The purpose of this paper is to manufacture quaternary polymer concretes and ... Keywords: Polymer concrete, Mechanical strength, Mixture design, Fly ash, Silica .... The silica foundry sand used was 101TM from the Silica Sand MFG .... To reduce the production cost of PCs, it is necessary to minimize the epoxy content in.

Improvement of Concrete Paving Blocks Properties by Mineral Additions

Directory of Open Access Journals (Sweden)

Aqeel Hatem Chkheiwer

2017-03-01

Full Text Available This research presents the results of experimental work on the various properties concrete paving blocks (CPB made with concrete containing different mineral additions.in this study, three types of mineral additions;Fly Ash (FA,Metakaolin (MK and Silica Fume (SF were used. Thirteen concretes mixes were cast at a water/binder ratio of 0.45 with 0, 5, 10,15and 20% cement replaced by either Fly ash,Metakaolin or Silica Fume. Theconcrete mixes were tested for slump, compressive strength, water absorption, and abrasion resistance.Metakaolin-contained concrete showed a better workability than fly ash and silica fume concrete. As the replacement level wasincreased, the 28-days compressive strength of the CPB containing MK increased similarly to that of the silica fume-containedCPB up to 20% replacement ratio. The replacement ratio of MK and SF from 5 to 20 % reduced water absorptionof CPB from5 to 19 than that of control mix. The increase in replacement ratio of MK andSF from 5 to 20 % leads to increasing abrasion resistance from 8 to 18% that of control mix

Effects of Medium Temperature and Industrial By-Products on the Key Hardened Properties of High Performance Concrete

Science.gov (United States)

Safiuddin, Md.; Raman, Sudharshan N.; Zain, Muhammad Fauzi Mohd.

2015-01-01

The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete. PMID:28793732

Effects of Medium Temperature and Industrial By-Products on the Key Hardened Properties of High Performance Concrete.

Science.gov (United States)

Safiuddin, Md; Raman, Sudharshan N; Zain, Muhammad Fauzi Mohd

2015-12-10

The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete.

Effects of Medium Temperature and Industrial By-Products on the Key Hardened Properties of High Performance Concrete

Directory of Open Access Journals (Sweden)

Md. Safiuddin

2015-12-01

Full Text Available The aim of the work reported in this article was to investigate the effects of medium temperature and industrial by-products on the key hardened properties of high performance concrete. Four concrete mixes were prepared based on a water-to-binder ratio of 0.35. Two industrial by-products, silica fume and Class F fly ash, were used separately and together with normal portland cement to produce three concrete mixes in addition to the control mix. The properties of both fresh and hardened concretes were examined in the laboratory. The freshly mixed concrete mixes were tested for slump, slump flow, and V-funnel flow. The hardened concretes were tested for compressive strength and dynamic modulus of elasticity after exposing to 20, 35 and 50 °C. In addition, the initial surface absorption and the rate of moisture movement into the concretes were determined at 20 °C. The performance of the concretes in the fresh state was excellent due to their superior deformability and good segregation resistance. In their hardened state, the highest levels of compressive strength and dynamic modulus of elasticity were produced by silica fume concrete. In addition, silica fume concrete showed the lowest level of initial surface absorption and the lowest rate of moisture movement into the interior of concrete. In comparison, the compressive strength, dynamic modulus of elasticity, initial surface absorption, and moisture movement rate of silica fume-fly ash concrete were close to those of silica fume concrete. Moreover, all concretes provided relatively low compressive strength and dynamic modulus of elasticity when they were exposed to 50 °C. However, the effect of increased temperature was less detrimental for silica fume and silica fume-fly ash concretes in comparison with the control concrete.

Fly ash/Kaolin based geopolymer green concretes and their mechanical properties

Directory of Open Access Journals (Sweden)

F.N. Okoye

2015-12-01

Full Text Available Geopolymer concrete mixes were cast using fly ash, kaolin, sodium hydroxide, potassium hydroxide, sodium silicate and aggregates. Portland cement concrete (M30 was used as a reference sample. The effect of silica fume, temperature (40 °C, 60 °C, 80 °C, 100 °C and 120 °C, sodium and potassium hydroxides and different superplasticizers on the compressive strength are reported [1]. Maximum strength was found at 100 °C and 14 M alkali solution [1].

Development of low-alkaline cement using pozzolans for geological disposal of long-lived radioactive waste

International Nuclear Information System (INIS)

Mihara, Morihiro; Iriya, Keishiro; Torii, Kazuyuki

2008-01-01

To reduce uncertainties in the safety assessment of the disposal system for long-lived radioactive waste, cement was developed which generates leachates with a lower pH than that of ordinary cement paste. This cement is termed 'low-alkaline cement'. Large amounts of pozzolans were used to produce the low-alkaline cement with ordinary Portland cement. Silica fume was found to be an effective pozzolans to reduce pH, but the needed large amount of silica fume reduced the workability of fresh concrete. Therefore, the authors also used fly ash with silica fume, to develop more workable low-alkaline cement, termed high-volume fly ash silica fume cement (HFSC). Two types of HFSC developed showed high compressive strength, smaller drying shrinkage and lower temperature rise than that of ordinary Portland cement. It was confirmed that HFSC could be used as self-compacting concrete. Therefore they can be applied as either structural or backfilling concrete in the disposal system. (author)

Effect of blended materials on U(VI) retention characteristics for portland cement solidification product

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2006-01-01

Using the simulated groundwater as leaching liquid, the retention capability of U(VI) in solidification products with Portland cement, the Portland cement containing silica fume, the Portland cement containing metakaolin and the Portland cement containing fly ash was researched by leaching experiments at 25 degree C for 42 d. The results indicate silica fume and metakaolin as blended materials can improve the U(VI) retention capability of Portland cement solidification product, but fly ash can not. (authors)

Effect of basalt, silica sand and fly ash on the mechanical properties ...

Indian Academy of Sciences (India)

2018-05-17

May 17, 2018 ... For this, we first manufactured binary PCs of epoxy/basalt ... Keywords. Polymer concrete; mechanical strength; mixture design; fly ash; silica sand; basalt. 1. .... To reduce the production cost of PCs, it is necessary to minimize ...

SCC modification by use of amorphous nano-silica

NARCIS (Netherlands)

Quercia Bianchi, G.; Spiesz, P.R.; Hüsken, G.; Brouwers, H.J.H.

2014-01-01

In this study two different types of nano-silica (nS) were applied in self-compacting concrete (SCC), both having similar particle size distributions (PSD), but produced through two different processes: fumed powder silica and precipitated silica in colloidal suspension. The influence of nano-silica

Stabilization / solidification of polluted marine dredged sediment of port en Bessin France, using hydraulic binders and silica fume

Science.gov (United States)

Silitonga, Ernesto

2017-09-01

A large amount of sediment is dredged in France every year. Due to the increase of the amount of marine dredged sediments, environmentally reuse of dredged sediment is urgently needed in France. The first objective of this study is to find an application for reuse of marine dredged sediments materials, as new material for road construction. Hence, serial tests need to be realized to identify if marine dredged sediment could be utilized for road construction. The second goal is to enhance the physical, mechanical and chemical characteristics of the mix, by incorporating binders and sediments, and revealed the identification of the mechanical characteristics measured on the mixes is compatible with their use as a base course material. The results show that the treatment by hydraulics binders could satisfy the needed mechanical characteristics. The present of Silica Fume is aimed to reduce the pollution level, especially the heavy metal content. However, the proportion of hydraulics binders and silica fume needed to meet prescribed specification is important, so the reuse of the marine dredged sediments of Port-en-Bessin, France in road construction, as an alternative material could be achieved. After the geotechnical study in laboratory results shown as expected than the study to identify the chemical characteristic realized. To evaluate the environmental impacts of the used material, leaching test is performed. The leaching test was performed to verify the predicted release of pollutants based on total dissolution. And for the final part, the test results show that the polluted marine dredged sediments could be safely used (in term of environmental impact) as a new material in road construction.

Fumed silica nanoparticle mediated biomimicry for optimal cell-material interactions for artificial organ development.

Science.gov (United States)

de Mel, Achala; Ramesh, Bala; Scurr, David J; Alexander, Morgan R; Hamilton, George; Birchall, Martin; Seifalian, Alexander M

2014-03-01

Replacement of irreversibly damaged organs due to chronic disease, with suitable tissue engineered implants is now a familiar area of interest to clinicians and multidisciplinary scientists. Ideal tissue engineering approaches require scaffolds to be tailor made to mimic physiological environments of interest with specific surface topographical and biological properties for optimal cell-material interactions. This study demonstrates a single-step procedure for inducing biomimicry in a novel nanocomposite base material scaffold, to re-create the extracellular matrix, which is required for stem cell integration and differentiation to mature cells. Fumed silica nanoparticle mediated procedure of scaffold functionalization, can be potentially adapted with multiple bioactive molecules to induce cellular biomimicry, in the development human organs. The proposed nanocomposite materials already in patients for number of implants, including world first synthetic trachea, tear ducts and vascular bypass graft. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Temperature dependence of autogenous shrinkage of silica fume cement pastes with a very low water–binder ratio

Energy Technology Data Exchange (ETDEWEB)

Maruyama, I., E-mail: ippei@dali.nuac.nagoya-u.ac.jp [Graduate School of Environmental Studies, Nagoya University, ES Building, No. 539, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Teramoto, A. [Graduate School of Environmental Studies, Nagoya University, Faculty of Engineering, ES Building, No. 546, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)

2013-08-15

Ultra-high-strength concrete with a large unit cement content undergoes considerable temperature increase inside members due to hydration heat, leading to a higher risk of internal cracking. Hence, the temperature dependence of autogenous shrinkage of cement pastes made with silica fume premixed cement with a water–binder ratio of 0.15 was studied extensively. Development of autogenous shrinkage showed different behaviors before and after the inflection point, and dependence on the temperature after mixing and subsequent temperature histories. The difference in autogenous shrinkage behavior poses problems for winter construction because autogenous shrinkage may increase with decrease in temperature after mixing before the inflection point and with increase in temperature inside concrete members with large cross sections.

Temperature dependence of autogenous shrinkage of silica fume cement pastes with a very low water–binder ratio

International Nuclear Information System (INIS)

Maruyama, I.; Teramoto, A.

2013-01-01

Ultra-high-strength concrete with a large unit cement content undergoes considerable temperature increase inside members due to hydration heat, leading to a higher risk of internal cracking. Hence, the temperature dependence of autogenous shrinkage of cement pastes made with silica fume premixed cement with a water–binder ratio of 0.15 was studied extensively. Development of autogenous shrinkage showed different behaviors before and after the inflection point, and dependence on the temperature after mixing and subsequent temperature histories. The difference in autogenous shrinkage behavior poses problems for winter construction because autogenous shrinkage may increase with decrease in temperature after mixing before the inflection point and with increase in temperature inside concrete members with large cross sections

21 CFR 584.700 - Hydrophobic silicas.

Science.gov (United States)

2010-04-01

...) Product. Amorphous fumed hydrophobic silica or precipitated hydrophobic silica (CAS Reg. No. 68611-0944... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Hydrophobic silicas. 584.700 Section 584.700 Food... DRUGS, FEEDS, AND RELATED PRODUCTS FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE IN FEED AND...

Fourth international conference on fly ash, silica fume, slag, and natural pozzolans in concrete: Supplemental proceedings

International Nuclear Information System (INIS)

Berry, E.E.; Hemmings, R.T.; Zhang, M.H.; Malhotra, V.M.

1992-03-01

This report consists of four papers presented at a special session on high volume fly ash (HVFA) concrete. These four papers summarize an EPRI research project currently in progress that is investigating HVFA concretes. This objective of this research is to commercialize the HVFA concrete technology through: (1) an extensive measurement of basic engineering and durability properties; (2) an examination of the binder microstructure and cementation hydration reactions; and (3) technology transfer to industry and the construction community. Overall the data from the project that are summarized in these papers, show that commercial quality structural grade concrete (up to 50 MPa compressive strength at 90 days) can be made from a wide range of fly ashes and cements available throughout the USA. It has been shown in this project that fly ash is a reactive participant with the Portland cement in the cementing process, and also serves as a microaggregate in a multiphase composite binder formed during curing. The properties of the binder were found to significantly influence strength development, elastic modulus, and the stress-strain behavior of HVFA concrete. Overall, the data presented show that regardless of the type of fly ash (from the nine US ashes evaluated) and the two cements used, that air-entrained HVFA concrete exhibits excellent durability in all respects except under application of deicing salts where some surface scaling has been observed in the laboratory

Pervious concrete using fly ash aggregate as coarse aggregate-an experimental study

Science.gov (United States)

Dash, Subhakanta; Kar, Biswabandita; Mukherjee, Partha Sarathi

2018-05-01

The present study deals with the fabrication of pervious concrete from fly ash aggregates. The pervious concrete were obtained by the mixture of three different size fly ash aggregates (4.75 mm,9.5 mm,12.5 mm), Portland cement, water with little amount of sand or without sand. Admixtures like Silica fume(SF) and Super plasticizer are added to the mixture to enhance the strength of concrete. Trial being taken on preparation of Fly ash based pervious concrete (FPC) with different w/c ratio i.e. 0.30, 0.35 and 0.40 respectively. Tests such as porosity, permeability and compressive, strength are studied for this concrete material and the result concluded that the concrete when cured for 28 days its compressive strength falls in between 7.15 - 15.74 MPa and permeability 9.38 - 16.07 mm/s with porosity 27.59 - 34.05% and these are suited to be used as for use as an environment friendly concrete.

STUDY ON SILICA INFUSED RECYCLED AGGREGATE CONCRETE USING DESIGN OF EXPERIMENTS

Directory of Open Access Journals (Sweden)

P. M. MRUDUL

2017-04-01

Full Text Available Recycled Aggregate (RA generated from the construction industry is used as a material for sustainable construction. The old mortar attached to these aggregates makes it porous and are generally used for low-grade applications. However, by infusing with silica fumes, the properties of recycled aggregate concrete (RAC can be improved, as the silica fumes get infused into the pores of old mortar attached to it. In this study, the optimum percentage of recycled aggregate that can be used in fresh concrete for higher grade applications was found out. Design of experiments (DoE was used to optimize percentage of silica fumes and recycled aggregate to achieve optimum properties of concrete. Equations to predict the properties of concrete were also modelled using regression analysis.

Relevant parameters in the micro silica selection for the self-flowing ultra-low cement castables production

International Nuclear Information System (INIS)

Studart, A.R.; Pandolfelli, V.C.; Rodrigues, J.A.; Vendrasco, S.L.

1997-01-01

Self-flowing ultra-low cement castables typically contain a large fraction of the particles, usually fume silica, which increase their flowability and mechanical strength at low temperatures. Fume silicas available in the market differ mainly from their amount of impurities. It is assumed that the content of soluble alkali and free carbon containing in this raw-material affects strongly the processing of self-flowing castable. In this work high alumina castables with gap-sized particle size distribution were prepared to evaluate their flowability, workability and mechanical strength for each sort of fume silica studied. It was observed that the amount of impurities affects both deflocculation and setting time of the castables and their cold and hot mechanical strength. Considerations regarding the physical and chemical characteristics relevant for selecting fume silicas for the production of self-flowing castables are presented and discussed. (author)

The effect of pozzolans and slag on the expansion of mortars cured at elevated temperature Part II: Microstructural and microchemical investigations

International Nuclear Information System (INIS)

Ramlochan, T.; Thomas, M.D.A.; Hooton, R.D.

2004-01-01

The microstructural and microchemical development of heat-cured Portland cement mortars containing silica fume, metakaolin, blast-furnace slag, and fly ash were analysed using pore solution analysis, X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy-dispersive X-ray analysis (EDX). Incorporation of these materials into the mixture modifies the composition of the C-S-H gel, the quantities of the hydration products, and the microstructure. Ettringite was formed during moist storage in all specimens, but was not accompanied by expansion where a sufficient amount of metakaolin, blast-furnace slag, or a suitable fly ash replaced a proportion of the Portland cement; replacement with silica fume was not as effective at eliminating expansion. The different behaviour of silica fume from the other supplementary cementing materials is believed to reflect a difference in the way ettringite is formed in the presence of Al 2 O 3 -bearing mineral admixtures

Effect of addition of different nano-clays on the fumed silica-polyethylene glycol based shear-thickening fluids

Science.gov (United States)

Singh, Mansi; Mehta, Rajeev; Verma, Sanjeev K.; Biswas, Ipsita

2018-01-01

A comparative study of the rheology of shear thickening suspensions of 20% fumed silica in polyethylene glycol (PEG200) with different nano clays as additives has been done. The nano-clays used are montmorillonite (MMT), Closite15A, Kaolin and Halloysite clay. The objective was to study the effect of relatively cost-effective clays as a partial substitute of silica. Specifically, the effect of type, concentration, temperature and frequency were considered. The results indicate that the shear thickening properties of Closite15A as additive in temperature ranges of 25 °C-45 °C performs the best and Halloysite performs best at higher (55 °C) and lower temperatures (5, 15 °C). The elasticity effects in dynamic experiments were markedly enhanced by Halloysite clay addition. Addition of MMT, however, led to insignificant enhancement in critical viscosity in steady-state as well as dynamic state-rheology. Interestingly, shear thickening fluid (STF) with all clay except MMT was stable after storing for more than a month. These findings indicate that the introduction of nano-clay as additives is a promising and cost effective method for enhancing the STF behavior which can be utilized in high impact resistant (about 3000% strain and 300 rad s-1 frequency) applications.

Effective utilizations of palm oil mill fly ash for synthetic amorphous silica and carbon zeolite composite synthesis

Science.gov (United States)

Utama, P. S.; Saputra, E.; Khairat

2018-04-01

Palm Oil Mill Fly Ash (POMFA) the solid waste of palm oil industry was used as a raw material for synthetic amorphous silica and carbon zeolite composite synthesis in order to minimize the wastes of palm oil industry. The alkaline extraction combine with the sol-gel precipitation and mechanical fragmentation was applied to produce synthetic amorphous silica. The byproduct, extracted POMFA was rich in carbon and silica content in a significant amount. The microwave heated hydrothermal process used to synthesize carbon zeolite composite from the byproduct. The obtained silica had chemical composition, specific surface area and the micrograph similar to commercial precipitated silica for rubber filler. The microwave heated hydrothermal process has a great potential for synthesizing carbon zeolite composite. The process only needs one-step and shorter time compare to conventional hydrothermal process.

Resistance to Corrosion of Reinforcement of High Volume Fly Ash Concrete

International Nuclear Information System (INIS)

Kwon, S. O.; Bae, S. H.; Lee, H. J.; Lee, K. M.; Jung, S. H.

2014-01-01

Due to the increasing of interest about the eco-friendly concrete, it is increased to use concretes containing by-products of industry such as fly ash(FA), ground granulated blast furnace slag(GGBFS), silica fume(SF), and etc. Especially, these are well known for improving the resistances to reinforcement corrosion in concrete and decreasing chloride ion penetration. The purpose of this experimental research is to evaluate the resistance against corrosion of reinforcement of high volume fly ash(HVFA) concrete which is replaced with high volume fly ash for cement volume. For this purpose, the concrete test specimens were made for various strength level and replacement ratio of FA, and then the compressive strength and diffusion coefficient for chloride ion of them were measured for 28, 91, and 182 days, respectively. Also, corrosion monitoring by half cell potential method was carried out for the made lollypop concrete test specimens to detect the time of corrosion initiation for reinforcement in concrete. As a result, it was observed from the test results that the compressive strength of HVFA concrete was decreased with increasing replacement ratio of FA but long-term resistances against reinforcement corrosion and chloride ion penetration of that were increased

Behaviour of Nano Silica in Tension Zone of High Performance Concrete Beams

Science.gov (United States)

Jaishankar, P.; Vivek, D.

2017-07-01

High performance concrete (HPC) is similar to High strength concrete (HSC).It is because of lowering of water to cement ratio, which is needed to attain high strength and generally improves other properties. This concrete contains one or more cementitious materials such as fly ash, Silica fume or ground granulated blast furnace slag and usually a super plasticizer. The term ‘high performance’ is somewhat different because the essential feature of this concrete is that it’s ingredients and proportions are specifically chosen so as to have particularly appropriate properties for the expected use of the structure such as high strength and low permeability. Usage of nano scale properties such as Nano SiO2 can result in dramatically improved properties from conventional grain size materials of same chemical composition. This project is more interested in evaluate the behaviour of nano silica in concrete for 5%, 10%, and 15% volume fraction of cement. Flexural test for beams were conducted with two point loads, at different percentage as mentioned above. From results interpolated, Nano silica with higher order replacement gives optimized results compared to control specimens.

Farklı Puzolanik Katkıların Çimento Harçlarının Mekanik Özelikleri Üzerine Etkisi = The Effect of Different Puzzolanic Additives on Mechanical Properties of Cement Mortars

Directory of Open Access Journals (Sweden)

H. Aygül YEPREM

2004-06-01

Full Text Available In this study, cement mortar samples containing fly ash obtained from Soma Power Plant, two different types of natural pozzolan supplied from Yenişehir and Bilecik and silica fume from Antalya Ferrocrom Industry partial replacement of cement clinker. The strength of the mortars prepared by these mixtures were investigated. The mixtures were prepared by using 10% fly ash and 5% silica fume and the trass contents varied as 30%, 35%, and 40%. Chemical analyses of these mixtures were carried out and Blaine specific surface area values were measured. In performed tests, the highest strength values were noticed in mortars containing natural puzzolan from Bilecik which has high fineness.

INVESTIGATION OF EFFECTS TO THE RHEOLOGICAL PROPERTIES OF ADDITIVE MATERIALS WHICH ARE USED ON CEMENT ENJECTIONS

Directory of Open Access Journals (Sweden)

Özcan TAN

2004-02-01

Full Text Available In this study the rheological properties of the injection mixtures containing various proportions of bentonite (B, fly ash (UK and silica fume (SD were investigated. L16 orthogonal array with three parameters and four levels was selected using Taguchi Design of Experiment Method. In the preparation of the injection mixtures the percentages of bentonite, fly ash and silica fume (by weight of solid used were 0 %, 0.5 %, 1 %, 3 %, 10 %, 20 %, 30 %, 40 %, and 0 %, 5 %, 10 %, 20 %, respectively. For the prepared injection mixtures the sedimentation and Marsh funnel experiments were performed. The experiments were carried out water to solid ratios (W/S of 1.25 and the experimental results were evaluated separately using Taguchi method. As a result of the evaluations; the most effective parameter on the flowing time (viscosity and the amount of sedimentation was determined as the silica fume. For the investigated properties of the injection mixtures the optimum mixing ratios were determined with the Taguchi method and for these ratios the confirmation experiments were performed.

Effects of nano-silica (NS) additions on durability of SCC mixtures

NARCIS (Netherlands)

Quercia Bianchi, G.; Spiesz, P.R.; Brouwers, H.J.H.; Andrade, C; Gulikers, JJW; Polder, R

2015-01-01

In this study, three different types of nano-silica were applied in self-compacting concrete (SCC), one produced by the controlled dissolution of the olivine mineral and two having similar particle size distributions (PSD), but produced through two different processes: fumed powder nano-silica and

Accelerator, superplasticiter and silica gome by wet shotcrete; Hormigon Proyectado por Via Humeda

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This project has been carried out by Geocontrol during the period September 1997-november 2000. The main target of this project was to establish a better knowledgement about the influence of the accelerator, silica fume, steel fibres and super plasticizer on the wet shotcrete properties. This project has been developed in three phases focused in three specifical targets: I. Effect of the accelerator, superplasticizer and silica fume dosages on shotcrete strength. II. Influence of steel fibres and silica fume on shotcrete characteristics. III. Steel fibres dosages and type effect of shotcrete absorbed energy. The main conclusions obtained from this research are the following. 1. Accelerators free of alkalis have a very little influence on the shotcrete strength reduction. 2. The best results are obtained when the accelerator dosage is the lowest, with a reference of the 4% of cement weigh. 3. The superplasticizer is very important in order to reach the lowest water/cement ratio. 4. Silica fume has a strong and positive influence on shotcrete characteristics but only if the dosages is higher than 30 kg/m''3. 5. The best results with silica fume are obtained when this product is added as a separate product, instead to be missed with other additive as superplasticizer. 6. Steel fibres addition improves dramatically the shotcrete post-failure characteristics. 7. A shotcrete without steel fibres and with a strength ranged between 25 and 40 MPa absorbers 130-180 Joules and another one with a steel mesh of 150x150x6 mm absorbers 1100 Joules. 8. Steel fibres shotcrete can reach the same energy absorption that another one reinforced with wire mesh. 9. During shotcreting the steel fibres dosages has a loss of 10 to 30 % due to shotcrete rebound. This research project allows to improve the knowledgement os shotcreting technique in order to use it with more efficiency than in the past. (Author)

Solid-state 27Al and 29Si NMR characterization of hydrates formed in calcium aluminate-silica fume mixtures

International Nuclear Information System (INIS)

Pena, P.; Rivas Mercury, J.M.; Aza, A.H. de; Turrillas, X.; Sobrados, I.; Sanz, J.

2008-01-01

Partially deuterated Ca 3 Al 2 (SiO 4 ) y (OH) 12-4y -Al(OH) 3 mixtures, prepared by hydration of Ca 3 Al 2 O 6 (C 3 A), Ca 12 Al 14 O 33 (C 12 A 7 ) and CaAl 2 O 4 (CA) phases in the presence of silica fume, have been characterized by 29 Si and 27 Al magic-angle spinning-nuclear magnetic resonance (MAS-NMR) spectroscopies. NMR spectroscopy was used to characterize anhydrous and fully hydrated samples. In hydrated compounds, Ca 3 Al 2 (OH) 12 and Al(OH) 3 phases were detected. From the quantitative analysis of 27 Al NMR signals, the Al(OH) 3 /Ca 3 Al 2 (OH) 12 ratio was deduced. The incorporation of Si into the katoite structure, Ca 3 Al 2 (SiO 4 ) 3-x (OH) 4x , was followed by 27 Al and 29 Si NMR spectroscopies. Si/OH ratios were determined from the quantitative analysis of 27 Al MAS-NMR components associated with Al(OH) 6 and Al(OSi)(OH) 5 environments. The 29 Si NMR spectroscopy was also used to quantify the unreacted silica and amorphous calcium aluminosilicate hydrates formed, C-S-H and C-A-S-H for short. From 29 Si NMR spectra, the amount of Si incorporated into different phases was estimated. Si and Al concentrations, deduced by NMR, transmission electron microscopy, energy dispersive spectrometry, and Rietveld analysis of both X-ray and neutron data, indicate that only a part of available Si is incorporated in katoite structures. - Graphical abstract: Transmission electron micrograph of CaAl 2 O 4 -microsilica mixture hydrated at 90 deg. C for 31 days showing a cubic Ca 3 Al 2.0±0.2 (SiO 4 ) 0.9±0.2 (OH) 1.8 crystal surrounded by unreacted amorphous silica spheres

Study on pore structure and diffusion coefficient of chloride ion in hardened low-alkaline cement

International Nuclear Information System (INIS)

Mihara, Morihiro; Torii, Kazuyuki

2009-03-01

Low-alkaline cement using pozzolans is under consideration as a possible filling and structural material in geological disposal for long-lived radioactive waste. Silica fume and fly ash are used to develop the low-alkaline cement which is named HFSC, High-volume Fly ash Silica fume Cement. In this study, pore structure and diffusivity of chloride ion in HFSC pastes were investigated in order to understand the fundamental transport properties of ions. HFSC which included different contents of fly ash (40%, 50% and 60%) with silica fume (20%) and ordinary Portland (OPC) cement were prepared. Hardened cement pastes were supplied to pore structure analysis and in-diffusion experiment with NaCl and CaCl 2 solution. Mercury intrusion method (MIP) commonly used and image analysis of backscattered electron microscopy (BSE) for pore in hardened cement paste were performed to investigate the pore structure. The porosity of HFSC was larger than that of OPC measured by MIP. However, pore diameter increasing pore volume of HFSC was smaller than that of OPC. It was observed that lager pores were in HFSC than in OPC from BSE. These large pores in HFSC were originated from cenosphere of FA. The apparent diffusivity of chloride in HFSC with fly ash of 40% showed smallest value in the cement pastes. It was concluded that the smallest diffusion coefficient was caused by a pore of HFSC which had a bended structure and ion exclusion/filtration effect. (author)

Class H cement hydration at 180 deg. C and high pressure in the presence of added silica

International Nuclear Information System (INIS)

Jupe, Andrew C.; Wilkinson, Angus P.; Luke, Karen; Funkhouser, Gary P.

2008-01-01

Under deep oil-well conditions of elevated temperature and pressure, crystalline calcium silicate hydrates are formed during Portland cement hydration. The use of silica rich mineral additives leads to the formation of crystalline hydrates with better mechanical properties than those formed without the additive. The effects of silica flour, silica fume (amorphous silica), and a natural zeolite mixture on the hydration of Class H cement slurries at 180 deg. C under externally applied pressures of 7 and 52 MPa are examined in real time using in-situ synchrotron X-ray diffraction. For some compositions examined, but not all, pressure was found to have a large effect on the kinetics of crystalline hydrate formation. The use of silica fume delayed both C 3 S hydration and the formation of crystalline silicate hydrates compared to what was seen with other silica sources

Synthesis, characterization and antimicrobial studies of bio silica ...

Indian Academy of Sciences (India)

2018-05-16

May 16, 2018 ... Cynodon dactylon; green approach; silica nanoparticles; characterization; antimicrobial studies. 1. .... The obtained powder was well-ground with a mortar and ..... Inhalation of SiCl4 fumes irritates nose, throat and lungs.

Fungus-Mediated Preferential Bioleaching of Waste Material Such as Fly - Ash as a Means of Producing Extracellular, Protein Capped, Fluorescent and Water Soluble Silica Nanoparticles

Science.gov (United States)

Khan, Shadab Ali; Uddin, Imran; Moeez, Sana; Ahmad, Absar

2014-01-01

In this paper, we for the first time show the ability of the mesophilic fungus Fusarium oxysporum in the bioleaching of waste material such as Fly-ash for the extracellular production of highly crystalline and highly stable, protein capped, fluorescent and water soluble silica nanoparticles at ambient conditions. When the fungus Fusarium oxysporum is exposed to Fly-ash, it is capable of selectively leaching out silica nanoparticles of quasi-spherical morphology within 24 h of reaction. These silica nanoparticles have been completely characterized by UV-vis spectroscopy, Photoluminescence (PL), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Energy dispersive analysis of X-rays (EDAX). PMID:25244567

Fungus-mediated preferential bioleaching of waste material such as fly - ash as a means of producing extracellular, protein capped, fluorescent and water soluble silica nanoparticles.

Directory of Open Access Journals (Sweden)

Shadab Ali Khan

Full Text Available In this paper, we for the first time show the ability of the mesophilic fungus Fusarium oxysporum in the bioleaching of waste material such as Fly-ash for the extracellular production of highly crystalline and highly stable, protein capped, fluorescent and water soluble silica nanoparticles at ambient conditions. When the fungus Fusarium oxysporum is exposed to Fly-ash, it is capable of selectively leaching out silica nanoparticles of quasi-spherical morphology within 24 h of reaction. These silica nanoparticles have been completely characterized by UV-vis spectroscopy, Photoluminescence (PL, Transmission electron microscopy (TEM, X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FTIR and Energy dispersive analysis of X-rays (EDAX.

Impact of nanoclay dispersed phenol formaldehyde/fumed silica nanocomposites on physico-mechanical and thermal properties

Science.gov (United States)

Lai, Josephine Chang Hui; Rahman, Md. Rezaur; Hamdan, Sinin

2017-12-01

In this study, the physical, mechanical and thermal properties of phenol formaldehyde/fumed silica/nanoclay (PF/FS/clay) nanocomposites were investigated. PF/FS/clay nanocomposites were prepared via condensation polymerization method and the effect of different clays as compatibilizers were subsequently investigated. The properties of nanocomposites were characterized through Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis (TGA) and tensile test. FT-IR results confirmed the condensation polymerization and the formation of nanocomposites. SEM result revealed that the surface-modified clay (1.34TCN) had better compatibility with PF/FS matrix compared to surface-modified clay (1.28E), clay (1.30E) and clay (1.31PS). Besides, clay (1.34TCN)-loaded nanocomposites showed better surface morphology among all the nanocomposites. Furthermore, PF/FS/clay (1.34TCN) nanocomposite exhibited better tensile strength and modulus up to 68% due to the strong interfacial bonding between the polymer matrix and fillers. Thermal stability of PF/FS/clay (1.34TCN) nanocomposite showed the highest weight percent loss at the final degradation stage with higher activation energy. Overall, this study proved that clay (1.34TCN) was the most suitable to be introduced in PF/FS matrix.

The analysis of lightweight brick strength pressure with mixture of glass powder and silica fume

Science.gov (United States)

Nursyamsi; Liang, William

2018-03-01

Little by little the engineers research how the development of concrete that can utilize waste. In the utilization of the waste, it can be functioned as mixing material which the chemical or the physical traits of the used goods contain similarity to the mixture of concrete in general, one of them is glass powder as the substitute of cement. The glass powder that utilizes is the one that is sifted through sieve No. 200 as much as 10% of the weight of the cement. The testing specimen of the concrete brick is make of the mixture with the ratio of 1:7, then is added with the foaming agent (1:30) and silica fume (10% of the weight of the cement). Furthermore, visual examination, absorption, net weight and testing specimen compressive strength. The data analysis uses the reference of SNI 03 – 0349 – 1989 regarding Concrete Brick for the Match for the Wall. Foaming Agent is make by using modified hand drill and brace. The testing specimen uses the brick mold with the size of 40 cm x 20cm x 10 cm. Based on this research, it shows that the quality that results from brick is still qualified based on SNI 03 – 0349 – 1989.

Optimization of compressive strength in admixture-reinforced cement-based grouts

Directory of Open Access Journals (Sweden)

Sahin Zaimoglu, A.

2007-12-01

Full Text Available The Taguchi method was used in this study to optimize the unconfined (7-, 14- and 28-day compressive strength of cement-based grouts with bentonite, fly ash and silica fume admixtures. The experiments were designed using an L16 orthogonal array in which the three factors considered were bentonite (0%, 0.5%, 1.0% and 3%, fly ash (10%, 20%, 30% and 40% and silica fume (0%, 5%, 10% and 20% content. The experimental results, which were analyzed by ANOVA and the Taguchi method, showed that fly ash and silica fume content play a significant role in unconfined compressive strength. The optimum conditions were found to be: 0% bentonite, 10% fly ash, 20% silica fume and 28 days of curing time. The maximum unconfined compressive strength reached under the above optimum conditions was 17.1 MPa.En el presente trabajo se ha intentado optimizar, mediante el método de Taguchi, las resistencias a compresión (a las edades de 7, 14 y 28 días de lechadas de cemento reforzadas con bentonita, cenizas volantes y humo de sílice. Se diseñaron los experimentos de acuerdo con un arreglo ortogonal tipo L16 en el que se contemplaban tres factores: la bentonita (0, 0,5, 1 y 3%, las cenizas volantes (10, 20, 30 y 40% y el humo de sílice (0, 5, 10 y 20% (porcentajes en peso del sólido. Los datos obtenidos se analizaron con mediante ANOVA y el método de Taguchi. De acuerdo con los resultados experimentales, el contenido tanto de cenizas volantes como de humo de sílice desempeña un papel significativo en la resistencia a compresión. Por otra parte, las condiciones óptimas que se han identificado son: 0% bentonita, 10% cenizas volantes, 20% humo de sílice y 28 días de tiempo de curado. La resistencia a compresión máxima conseguida en las anteriores condiciones era de 17,1 MPa.

A New Route for Preparation of Hydrophobic Silica Nanoparticles Using a Mixture of Poly(dimethylsiloxane and Diethyl Carbonate

Directory of Open Access Journals (Sweden)

Iryna Protsak

2018-01-01

Full Text Available Organosilicon layers chemically anchored on silica surfaces show high carbon content, good thermal and chemical stability and find numerous applications as fillers in polymer systems, thickeners in dispersing media, and as the stationary phases and carriers in chromatography. Methyl-terminated poly(dimethylsiloxanes (PDMSs are typically considered to be inert and not suitable for surface modification because of the absence of readily hydrolyzable groups. Therefore, in this paper, we report a new approach for surface modification of silica (SiO2 nanoparticles with poly(dimethylsiloxanes with different lengths of polymer chains (PDMS-20, PDMS-50, PDMS-100 in the presence of diethyl carbonate (DEC as initiator of siloxane bond splitting. Infrared spectroscopy (IR, elemental analysis (CHN, transmission electron microscopy (TEM, atomic force microscopy (AFM, rotational viscosity and contact angle of wetting were employed for the characterization of the raw fumed silica and modified silica nanoparticles. Elemental analysis data revealed that the carbon content in the grafted layer is higher than 8 wt % for all modified silicas, but it decreases significantly after sample treatment in polar media for silicas which were modified using neat PDMS. The IR spectroscopy data indicated full involvement of free silanol groups in the chemisorption process at a relatively low temperature (220 °C for all resulting samples. The contact angle studies confirmed hydrophobic surface properties of the obtained materials. The rheology results illustrated that fumed silica modified with mixtures of PDMS-x/DEC exhibited thixotropic behavior in industrial oil (I-40A, and exhibited a fully reversible nanostructure and shorter structure recovery time than nanosilicas modified with neat PDMS. The obtained results from AFM and TEM analysis revealed that the modification of fumed silica with mixtures of PDMS-20/DEC allows obtaining narrow particle size distribution with

Influence of silica fume on mechanical and physical properties of recycled aggregate concrete

Directory of Open Access Journals (Sweden)

Özgür Çakır

2015-08-01

Full Text Available Several studies related to sustainable concrete construction have encouraged development of composite binders, involving Portland cement, industrial by-products, and concrete mixes with partial replacement of natural aggregate with recycled aggregate. In this paper, the effects of incorporating silica fume (SF in the concrete mix design to improve the quality of recycled aggregates in concrete are presented. Portland cement was replaced with SF at 0%, 5% and 10%. Specimens were manufactured by replacing natural aggregates with recycled aggregates. Two size fractions (4/12 mm and 8/22 mm as recycled aggregates were used and four series of concrete mixtures were produced. In all concrete mixtures, a constant water/binder ratio at 0.50 was used and concrete mixtures with a target initial slump of S4 class (16–21 cm were prepared. Concrete properties were evaluated by means of compressive strength, tensile splitting strength, water absorption and ultrasonic pulse velocity and it was found that, using 10% SF as a cement replacement for recycled aggregate concretes enhanced the mechanical and physical properties of concrete. At all the test ages the tensile splitting strength gain of the natural aggregate concrete mixture (NA with and without SF was higher than that of the recycled concrete mixtures. Continuous and significant improvement in the tensile splitting strength of recycled aggregate concretes incorporating SF was observed. Similar to compressive strength test results, concrete incorporating 10% SF and containing 4/12 mm fraction recycled aggregates showed better performance among recycled aggregate concretes.

Self-compacting geopolymer concrete-a review

Science.gov (United States)

Ukesh Praveen, P.; Srinivasan, K.

2017-11-01

In this construction world, Geopolymer concrete is a special concrete which doesn’t requires the Ordinary Portland Cement and also reduces the emission of carbon-dioxide. The Geopolymer Concrete is made up of industrial by-products (which contains more Silica and Alumina) and activated with the help of Alkaline solution (combination of sodium hydroxide & sodium silicate or potassium hydroxide & potassium silicate). The high viscosity nature of Geopolymer Concrete had the ability to fail due to lack of compaction. In improvising the issue, Self Compacting Geopolymer Concrete has been introduced. The SCGC doesn’t require any additional compaction it will flow and compacted by its own weight. This concrete is made up of industrial by-products like Fly ash, GGBFS and Silica Fume and activated with alkaline solution. The earlier research was mostly on Fly ash based SCGC. In few research works Fly ash was partially replaced with GGBS and Silica Fume. They evaluated the compressive strength of concrete with varying molarities of NaOH; curing time and curing temperature. The flexural behaviour of the concrete also examined. The Fly ash based SCGC was got high compressive strength in heat curing as well as low compressive strength in ambient curing. The presence of GGBS improves the strength in ambient curing. For aiming the high strength in ambient curing Fly ash will be completely replace and examine with different mineral admixtures.

physico-chemical studies on polymer impregnated blending cement mortar composite

International Nuclear Information System (INIS)

Abdel-Rahman, H.A.

2001-01-01

as the increasing of the demand on a specific performance characteristics in concrete such as improved strength, low heat, sulfate resistance, improved impermeability and certain other applications. some of the industrial waste materials such as the blast-furnace slag, silica fume and fly ash were mixed with the cement clinker to produce blended cement . the use of these materials modifies the strength, pore structure and permeability of hardened cement mortar or concrete. the incorporation of blast furnace slag and silica fume in the hardened blended cement mortar or concrete is a common practice recently due to technological, economical and environmental benefits

pozzolanicity and some engineering properties of rice husk ash

African Journals Online (AJOL)

HON

, a potential ... relationship between the compressive strength of its concrete and water-cement ratio was also studied. The optimum water-cement ratio was found to .... solution, fly Ash, Silica Fume, Slag and. Natural Pozzolans in concrete, 1,.

Laboratory investigation of nanomaterials to improve the permeability and strength of concrete.

Science.gov (United States)

2010-02-01

Concretes containing various supplementary cementitious materials (SCMs) such as silica fume, fly ash, and slag have improved properties. Nanomaterials (a nanometer, nm, is 10-9 m), new SCMs with possible applications in concrete, have the smallest p...

Conversion of South African coal fly ash into high-purity ZSM-5 zeolite without additional source of silica or alumina and its application as a methanol-to-olefins catalyst

CSIR Research Space (South Africa)

Missengue, RNM

2018-03-01

Full Text Available Characteristics of ZSM-5 synthesized from H2SO4-treated coal fly ash and fused coal fly ash extracts are compared in this study. In the synthesis process, fused coal fly ash extract (without an additional silica source) was used in the synthesis...

Particle release and control of worker exposure during laboratory-scale synthesis, handling and simulated spills of manufactured nanomaterials in fume hoods

Science.gov (United States)

Fonseca, Ana S.; Kuijpers, Eelco; Kling, Kirsten I.; Levin, Marcus; Koivisto, Antti J.; Nielsen, Signe H.; Fransman, W.; Fedutik, Yijri; Jensen, Keld A.; Koponen, Ismo K.

2018-02-01

Fume hoods are one of the most common types of equipment applied to reduce the potential of particle exposure in laboratory environments. A number of previous studies have shown particle release during work with nanomaterials under fume hoods. Here, we assessed laboratory workers' inhalation exposure during synthesis and handling of CuO, TiO2 and ZnO in a fume hood. In addition, we tested the capacity of a fume hood to prevent particle release to laboratory air during simulated spillage of different powders (silica fume, zirconia TZ-3Y and TiO2). Airborne particle concentrations were measured in near field, far field, and in the breathing zone of the worker. Handling CuO nanoparticles increased the concentration of small particles (control during synthesis and handling of nanomaterials. An appropriate fume hood with adequate sash height and face velocity prevents 98.3% of particles release into the surrounding environment. Care should still be made to consider spills and high cleanliness to prevent exposure via resuspension and inadvertent exposure by secondary routes.

Influence of palm oil fuel ash on fresh and mechanical properties of ...

Indian Academy of Sciences (India)

percentage of cement, with several supplementary cementitious materials (SCM) such as silica fume, ground granulated blast-furnace slag, fly ash and rice husk ash ..... Safiuddin M, West J and Soudki K 2011b Flowing ability of the mortars ...

Fulltext PDF

Indian Academy of Sciences (India)

Niyazi Ugur Kockal

2018-04-04

Apr 4, 2018 ... amounts of silica fume and calcium hydroxide as binding materials, acidic ... ties of treated palm oil fly ash (TPOFA)-based .... (a) Flexural strength test set-up, (b) broken parts of specimen, (c) compressive strength test set-up.

Influence of microstructure on the diffusive transport in pastes, mortars and concretes made with cement Portland and silica fume

International Nuclear Information System (INIS)

Bajja, Zineb

2016-01-01

Thanks to its high mechanical strength and its potential containment capacity conferred by a compact microstructure, concrete is considered as the most suitable material to compose the engineered barrier of some radioactive waste storage structure. Knowledge of diffusion properties and microstructure of these cementitious materials is then essential to study their long-term durability. In a more specific context of low and intermediate waste management, the use of formulations containing silica fume (SF) appears of great importance. The experimental approach consists in selecting many formulations of pastes and mortars to test by the HTO through-out diffusion test. Their initial compositions (water to binder ratio, SF content, sand content and particle size) were varied in order to browse different microstructures and diffusion properties, and to see the influence of each parameter (water, SF, content and grain size of sand) on the evolution of diffusivity within these materials. The microstructure was investigated to interpret the obtained values of diffusion coefficients. Different complementary techniques have been used to characterize the porous structure (water and mercury intrusion porosimetry, nitrogen adsorption), to verify SF reactivity (TGA, SEM associated to EDS) or to determine the profile porosity at ITZ (SEM combined with image analysis).The relationship between microstructure and diffusion coefficients (DeHTO) was then discussed. The ultimate goal was to find a link between microstructure properties and transport parameters to estimate from a simple characterization, the DeHTO of concrete, difficult to get from HTO diffusion cells test. Other attempts have also been made to try to assess the concrete diffusion coefficient, such as the multi-scale modeling approach (the scale of hydrates 3D model), or the diffusion of other elements ( like oxygen or nitrogen). This study shows that silica fume agglomerates (slurry) observed in cement paste and mortar

Synthesis of Novel Mesoporous Silica Materials with Hierarchical Pore Structures

Energy Technology Data Exchange (ETDEWEB)

Yoon, Suk Bon; Choi, Wang Kyu; Choi, Byung Seon; Moon, Jei Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-05-15

Porous materials with various pore sizes in the range of micropore (< 2 nm), mesopore (2-50 nm), and macropore (> 50 nm) are attractive due to their many emerging applications such as catalysts, separation systems, and low dielectric constant materials. The discovery of new M41S mesoporous silica families with pore sizes larger than 2 nm in diameter in 1992 extended the applications into much wider pore ranges, bringing in a new prosperous era in porous material research. The synthesis of these silica materials has been mainly accomplished through a self-assembly between surfactant molecules and inorganic species under various pH conditions. Recently, core-shell nanoparticles with a silica core and mesoporous shell under basic conditions were synthesized using the silica nanoparticles as a core, and a silica precursor (TEOS) and cationic surfactant (CTABr) as a material for the formation of the mesoporous shell. The resultant materials were very monodispersive in size and showed a narrow pore size distribution in the range of ca 2-3 nm in diameter, depending on the alkyl-chain length of the surfactants used. In this work, the mesoporous shell coated-fumed silicas (denoted as MS M-5s) were synthesized by using fumed silica instead of the silica nanoparticle as a core based on previous reports. Also, the structural properties of the MS M-5s such as the specific surface area and pore volume were easily controlled by varying the amount of the silica precursor and surfactant. The resultant materials exhibited a BET surface area of ca 279-446 m{sup 2}/g and total pore volume of ca 0.64-0.74 cm{sup 3}/g and showed a narrow pore size distribution (PSD) due to the removal of the organic surfactant molecules

Packing issue in cement blending for sustainability developments - Approach by discrete element method

NARCIS (Netherlands)

Le, L.B.N.; Stroeven, P.

2014-01-01

Common cement blending materials for concrete like fly ashes, blast furnace slag, silica fume, metakaolin and rice husk ash have been investigated experimentally as to their impact on concrete’s mechanical, physical and sustainability capabilities. Such efforts offer but case-related information on

Use of supplemental cementitious materials for optimum resistance of concrete to chloride penetration.

Science.gov (United States)

1989-01-01

This study was conducted to determine whether significant improvements could be achieved in the resistance to the penetration by chloride ions of concretes with fly ash or slag by the addition of silica fume with either Type II or Type III cement and...

Visibility in sodium fume

International Nuclear Information System (INIS)

Hughes, G.W.; Anderson, N.R.

1971-01-01

The appearance of sodium fume of unknown concentration and the effects of short term exposure on unprotected workers is described. The molecular extinction coefficient of sodium fume is calculated from which light transmission data, and a rapid method for the estimation of the fume concentration is proposed. (author)

Assessment of high performance concrete containing fly ash and calcium nitrite based corrosion inhibitor as a mean to prevent the corrosion of reinforcing steel

International Nuclear Information System (INIS)

Montes-García, P; Jiménez-Quero, V; López-Calvo, H

2015-01-01

This research analyses the effectiveness of the water-to-cement ratio (w/c), fly ash and a calcium nitrite based corrosion inhibitor to prevent the corrosion of reinforcing steel embedded in high performance concrete. The interactive effect between the inhibitor and fly ash was evaluated because the occurrence of a negative effect when both ingredients are added together in a concrete mixture has been reported. All the concrete mixtures studied in this investigation had 8.2% of silica fume. Twenty seven prismatic concrete specimens were fabricated with dimensions of 55 × 230 × 300 mm each containing two steel rods embedded for the purpose of corrosion monitoring. The specimens were exposed to a simulated marine environment with two daily cycles of wetting and drying for one year. To evaluate the deterioration of the specimens corrosion potentials and linear polarization resistance tests were carried out. The results indicate that the use of a low w/c, the addition of fly ash and the addition of the corrosion inhibitor contributed to the reduction of the corrosion of steel in the concrete specimens. The results further suggest that the combination of fly ash and corrosion inhibitor does not promote the deterioration of the concrete matrix

Room Temperature Imprint Using Crack-Free Monolithic SiO2-PVA Nanocomposite for Fabricating Microhole Array on Silica Glass

Directory of Open Access Journals (Sweden)

Shigeru Fujino

2015-01-01

Full Text Available This paper aims to fabricate microhole arrays onto a silica glass via a room temperature imprint and subsequent sintering by using a monolithic SiO2-poly(vinyl alcohol (PVA nanocomposite as the silica glass precursor. The SiO2-PVA suspension was prepared from fumed silica particles and PVA, followed by drying to obtain tailored SiO2-PVA nanocomposites. The dependence of particle size of the fumed silica particles on pore size of the nanocomposite was examined. Nanocomposites prepared from 7 nm silica particles possessed suitable mesopores, whereas the corresponding nanocomposites prepared from 30 nm silica particles hardly possessed mesopores. The pore size of the nanocomposites increased as a function of decreasing pH of the SiO2-PVA suspension. As a consequence, the crack-free monolithic SiO2-PVA nanocomposite was obtained using 7 nm silica particles via the suspension at pH 3. Micropatterns were imprinted on the monolithic SiO2-PVA nanocomposite at room temperature. The imprinted nanocomposite was sintered to a transparent silica glass at 1200°C in air. The fabricated sintered glass possessed the microhole array on their surface with aspect ratios identical to the mold.

Effects of Mineral Admixtures, Water Binder Ratio and Curing on ...

African Journals Online (AJOL)

Suitable addition of mineral admixtures like fly ash (FA), silica fume (SF), metakaolin (MK) etc., in concrete improves strength and durability characteristics of concrete. This paper presents the laboratory investigation on the effects of mineral admixtures and water binder ratio on compressive strength is discussed. The study ...

microstructural characterisation, physical and chemical properties

African Journals Online (AJOL)

Mrs Abiodun

cementing materials are Rice Husk Ash (RHA), silica fume, fly ash and ash ... pozzolan, give rise to its consideration as an alternative binder by partial ..... of concrete with mineral admixtures and its effect ... ash on the compressive strength of concrete'',. Nigerian ... based lightweight foamed concrete with cement partially ...

In situ formation of sintered cordierite–mullite nano–micro composites by utilizing of waste silica fume

International Nuclear Information System (INIS)

Khattab, R.M.; EL-Rafei, A.M.; Zawrah, M.F.

2012-01-01

Highlights: ► We succeeded to obtain in situ formed sintered cordierite–mullite nano–macro composites from waste and pure materials at 1400 °C. ► Their sinterability was greatly dependent on both firing temperature and composition. ► XRD patterns showed that the optimum temperature required for formation of sintered cordierite–mullite nano–macro composites was achieved at 1400 °C. ► The batch containing 70 wt.% cordierite and 30 wt.% mullite exhibited the best properties. ► Microstructures of the densified composites were composed of nano–macro cordierite–mullite structures. -- Abstract: This study aims at in situ formation of sintered cordierite–mullite nano–macro composites having high technological properties using waste silica fume, calcined ball clay, calcined alumina, and magnesia as starting materials. The starting materials were mixed in different ratios to obtain different cordierite–mullite composite batches in which the cordierite contents ranged from 50 to 100 wt.%. The batches were uni-axially pressed at 100 MPa and sintered at 1350, 1400 and 1450 °C to select the optimum temperature required for cordierite–mullite nano–macro composites formation. The formed phases were identified by X-ray diffraction (XRD) pattern. The sintering parameters in terms of bulk density (BD) and apparent porosity (AP) were determined. The microstructure of composites has been investigated by scanning electron microscope (SEM). Cold crushing strength (CCS) of the sintered batches was evaluated. The result revealed that the cordierite–mullite nano–macro composites were in-situ formed at 1400 °C. The batch containing 70 wt.% cordierite showed good physical and mechanical properties.

222-S LABORATORY FUME HOOD TESTING STUDY

International Nuclear Information System (INIS)

RUELAS, B.H.

2007-01-01

The 222-S Laboratory contains 155 active fume hoods that are used to support analytical work with radioactive and/or toxic materials. The performance of a fume hood was brought into question after employees detected odors in the work area while mixing chemicals within the subject fume hood. Following the event, testing of the fume hood was conducted to assess the performance of the fume hood. Based on observations from the testing, it was deemed appropriate to conduct performance evaluations of other fume hoods within the laboratory

Amorphous silica in ultra-high performance concrete: First hour of hydration

Energy Technology Data Exchange (ETDEWEB)

Oertel, Tina, E-mail: tina.oertel@isc.fraunhofer.de [Fraunhofer-Institute for Silicate Research ISC, Neunerplatz 2, 97082 Würzburg (Germany); Chair for Inorganic Chemistry I, Universität Bayreuth, Universitätsstr. 30, 95440 Bayreuth (Germany); Hutter, Frank [Fraunhofer-Institute for Silicate Research ISC, Neunerplatz 2, 97082 Würzburg (Germany); Helbig, Uta, E-mail: uta.helbig@th-nuernberg.de [Chair for Crystallography and X-ray Methods, Technische Hochschule Nürnberg Georg Simon Ohm, Wassertorstraße 10, 90489 Nürnberg (Germany); Sextl, Gerhard [Fraunhofer-Institute for Silicate Research ISC, Neunerplatz 2, 97082 Würzburg (Germany); Chair for Chemical Technology of Advanced Materials, Julius Maximilian Universität, Röntgenring 11, 97070 Würzburg (Germany)

2014-04-01

Amorphous silica in the sub-micrometer size range is widely used to accelerate cement hydration. Investigations including properties of silica which differ from the specific surface area are rare. In this study, the reactivity of varying types of silica was evaluated based on their specific surface area, surface silanol group density, content of silanol groups and solubility in an alkaline suspension. Pyrogenic silica, silica fume and silica synthesized by hydrolysis and condensation of alkoxy silanes, so-called Stoeber particles, were employed. Influences of the silica within the first hour were further examined in pastes with water/cement ratios of 0.23 using in-situ X-ray diffraction, cryo scanning electron microscopy and pore solution analysis. It was shown that Stoeber particles change the composition of the pore solution. Na{sup +}, K{sup +}, Ca{sup 2+} and silicate ions seem to react to oligomers. The extent of this reaction might be highest for Stoeber particles due to their high reactivity.

CCN activation of fumed silica aerosols mixed with soluble pollutants

Science.gov (United States)

Dalirian, M.; Keskinen, H.; Ahlm, L.; Ylisirniö, A.; Romakkaniemi, S.; Laaksonen, A.; Virtanen, A.; Riipinen, I.

2014-09-01

Particle-water interactions of completely soluble or insoluble particles are fairly well understood but less is known of aerosols consisting of mixtures of soluble and insoluble components. In this study, laboratory measurements were performed to investigate cloud condensation nuclei (CCN) activity of silica particles coated with ammonium sulphate (a salt), sucrose (a sugar) and bovine serum albumin known as BSA (a protein). In addition, the agglomerated structure of the silica particles was investigated by estimating the surface equivalent diameter based on measurements with a Differential Mobility Analyzer (DMA) and an Aerosol Particle Mass Analyzer (APM). By using the surface equivalent diameter the non-sphericity of the particles containing silica was accounted for when estimating CCN activation. Furthermore, characterizing critical supersaturations of particles consisting of pure soluble on insoluble compounds using existing frameworks showed that the CCN activation of single component particles was in good agreement with Köhler and adsorption theory based models when the agglomerated structure was accounted for. For mixed particles the CCN activation was governed by the soluble components, and the soluble fraction varied considerably with particle size for our wet-generated aerosols. Our results confirm the hypothesis that knowing the soluble fraction is the key parameter needed for describing the CCN activation of mixed aerosols, and highlight the importance of controlled coating techniques for acquiring a detailed understanding of the CCN activation of atmospheric insoluble particles mixed with soluble pollutants.

On the effectiveness of incorporating shear thickening fluid with fumed silica particles in hip protectors

Science.gov (United States)

Haris, A.; Goh, B. W. Y.; Tay, T. E.; Lee, H. P.; Rammohan, A. V.; Tan, V. B. C.

2018-01-01

The objective of this research is to develop a smart hip protector by incorporating shear thickening fluid (STF) into conventional foam hip protectors. The shear thickening properties of fumed silica particles dispersed in liquid polyethylene glycol (PEG) were determined from rheological tests. Dynamic drop tests, using a 4 kg drop platen at 0.5 m drop height, were conducted to study how STF improves energy absorption as compared to unfilled foam and PEG filled foam. The results show that PEG filled foam reduces the mean peak force transmitted by a further 55% and mean peak displacement by 32.5% as compared to the unfilled foam; the STF filled foam further reduces mean peak force and displacement by 15% and 41% respectively when compared to the PEG filled foam. At a displacement of 22 mm, the STF filled foam absorbs 7.4 times more energy than the PEG filled foam. The results of varying the drop mass and drop height show that the energy absorbed per unit displacement for STF filled foam is always higher than that of PEG filled foam. Finally, the effectiveness of a prototype of hip protector made from 15 mm thick STF filled foam in preventing hip fractures was studied under two different loading conditions: distributed load (plate drop test) and concentrated load (ball drop test). The results of the plate and ball drop tests show that among all hip protectors tested in this study, only the prototype can reduce the mean peak impact force to be lower than the force required to fracture a hip bone (3.1 kN) regardless of the type of loading. Moreover, the peak force of the prototype is about half of this value, suggesting thinner prototype could have been used instead. These findings show that STF is effective in improving the performance of hip protectors.

Impact behavior of f-silica and amine terminated polybutadiene co-acrylonitrile rubber modified novolac epoxy/Kevlar nanocomposites

Science.gov (United States)

Kavita, Pal, Vijayeta; Tiwari, R. K.

2018-05-01

In the present work, nano-fumed silica treated with 3-Glycidoxypropyl trimethoxy silane (f-silica) was used as a nanoreinforcement in the fabrication of amine terminated polybutadiene co-acrylonitrile rubber (ATBN) modified Kevlar/epoxy based nanocomposites. Nanocomposites with different f-silica loading (0, 0.5, 1.0 and 2.0 wt. %) and having same ATBN (10 wt. %) were made and characterized by Izod impact test for evaluating impact strength values. All the nanocomposites showed better impact strength than neat Kevlar/novolac epoxy based composite.

Preferential adsorption of polycarboxylate superplasticizers on cement and silica fume in ultra-high performance concrete (UHPC)

International Nuclear Information System (INIS)

Schröfl, Ch.; Gruber, M.; Plank, J.

2012-01-01

UHPC is fluidized particularly well when a blend of MPEG- and APEG-type PCEs is applied. Here, the mechanism for this behavior was investigated. Testing individual cement and micro silica pastes revealed that the MPEG-PCE disperses cement better than silica whereas the APEG-PCE fluidizes silica particularly well. This behavior is explained by preferential adsorption of APEG-PCE on silica while MPEG-PCEs exhibit a more balanced affinity to both cement and silica. Adsorption data obtained from individual cement and micro silica pastes were compared with those found for the fully formulated UHPC containing a cement/silica blend. In the UHPC formulation, both PCEs still exhibit preferential and selective adsorption similar as was observed for individual cement and silica pastes. Preferential adsorption of PCEs is explained by their different stereochemistry whereby the carboxylate groups have to match with the steric position of calcium ions/atoms situated at the surfaces of cement hydrates or silica.

Evaluating the effect of crumb rubber and nano silica on the properties of high volume fly ash roller compacted concrete pavement using non-destructive techniques

Directory of Open Access Journals (Sweden)

Bashar S. Mohammed

2018-06-01

Full Text Available The major problems related to roller compacted concrete (RCC pavement are high rigidity, lower tensile strength which causes a tendency of cracking due to thermal or plastic shrinkage, flexural and fatigue loads. Furthermore, RCC pavement does not support the use of dowel bars or reinforcement due to the way it is placed and compacted, these also aided in cracking and consequently increased maintenance cost. To address these issues, high volume fly ash (HVFA RCC pavement was developed by partially replacing 50% cement by volume with fly ash. Crumb rubber was used as a partial replacement to fine aggregate in HVFA RCC pavement at 0%, 10%, 20%, and 30% replacement by volume. Nano silica was added at 0%, 1%, 2% and 3% by weight of cementitious materials to improve early strength development in HVFA RCC pavement and mitigate the loss of strength due to the incorporation of crumb rubber. The nondestructive technique using the rebound hammer test (RHT and ultrasonic pulse velocity (UPV were used to evaluate the effect of crumb rubber and nano silica on the performance of HVFA RCC pavement. The results showed that the use of HVFA as cement replacement decreases both the unit weight, compressive strength, rebound number (RN. Furthermore, the unit weight, compressive strength, RN, UPV and dynamic modulus of elasticity of HVFA RCC pavement all decreases with increase in crumb rubber content and increases with the addition of nano-silica. Combined UPV-RN (SonReb models for predicting the 28 days strength of HVFA RCC pavement based on combining UPV and RN were developed using multivariable regression (double power, bilinear, and double exponential models. The exponential combined SonReb model is the most suitable for predicting the compressive strength of HVFA RCC pavement using UPV and RN as the independent variable with better predicting ability, higher correlation compared to the single variable models. Keywords: Crumb rubber, High volume fly ash, Nano

In situ prepared PET nanocomposites: Effect of organically modified montmorillonite and fumed silica nanoparticles on PET physical properties and thermal degradation kinetics

International Nuclear Information System (INIS)

Vassiliou, A.A.; Chrissafis, K.; Bikiaris, D.N.

2010-01-01

In the present study a series of PET nanocomposites were prepared by in situ polymerization using different amounts of organically modified montmorillonite (OMMT) with a triphenylphosphine compound and fumed silica nanoparticles (SiO 2 ). As verified by TEM micrographs, the dispersion of both nanoparticles into the PET matrix was homogeneous while montmorillonite was dispersed in the exfoliated form. The intrinsic viscosities of the prepared nanocomposites were affected by the addition of the nanoparticles and in both cases a slight increase was observed. Tensile strength was also increased by increasing nanoparticles content while both types of nanoparticles act as nucleating agents, enhancing the crystallization rates of PET. From the thermogravimetric curves it was concluded that PET and the samples with different nanoparticles presented good thermostability, since no remarkable mass loss occurred up to 320 o C ( 2 2 wt.% nanocomposites was almost identical (222.1 kJ/mol). However, PET/OMMT 2 wt.% nanocomposites exhibited a higher activation energy (228.3 kJ/mol), indicating that OMMT incurred a stabilizing effect upon the decomposition of the matrix. The form of the conversion function for all the studied samples obtained by fitting was the mechanism of n th -order auto-catalysis.

Alkali content of fly ash : measuring and testing strategies for compliance.

Science.gov (United States)

2015-04-01

Sodium and potassium are the common alkalis present in fly ash. Excessive amounts of fly ash alkalis can cause efflorescence : problems in concrete products and raise concern about the effectiveness of the fly ash to mitigate alkali-silica reaction (...

Effects of Silica in Rice Husk Ash (RHA) in producing High Strength Concrete

OpenAIRE

Kartini, K; Nurul Nazierah, M.Y; Zaidahtulakmal, M.Z; Siti Aisyah, G

2012-01-01

High strength concrete (HSC) are known to have a higher amount of cement binder in the mix design properties with low w/b ratio. The high mass of cement content produced substantial heat liberation in the concrete due to the reaction between cement and water, which can lead to cracking. Additive likes silica fume is too expensive to use in the HSC in order to overcome the problems, however, the initiative of utilizing the rice husk ash (RHA) which have high silica content are apply for the de...

Hydrophobic silica nanoparticles as reinforcing filler for poly (lactic acid polymer matrix

Directory of Open Access Journals (Sweden)

Pilić Branka M.

2016-01-01

Full Text Available Properties of poly (lactic acid (PLA and its nanocomposites, with silica nanoparticles (SiO2, as filler were investigated. Neat PLA films and PLA films with different percentage of hydrophobic fumed silica nanoparticles (0.2, 0.5, 1, 2, 3 and 5 wt. % were prepared by solution casting method. Several tools were used to characterize the influence of different silica content on crystalline behavior, and thermal, mechanical and barrier properties of PLA/SiO2 nanocomposites. Results from scanning electron microscope (SEM showed that the nanocomposite preparation and selection of specific hydrophobic spherical nano filler provide a good dispersion of the silica nanoparticles in the PLA matrix. Addition of silica nanoparticles improved mechanical properties, the most significant improvement being observed for lowest silica content (0.2wt.%. Barrier properties were improved for all measured gases at all loadings of silica nanoparticles. The degree of crystallinity for PLA slightly increased by adding 0.2 and 0.5 wt. % of nano filler. [Projekat Ministarstva nauke Republike Srbije, br. III46001

Non-isothermal crystallization kinetic of poly(ethylene terephthalate)/fumed silica (PET/SiO2) prepared by in situ polymerization

International Nuclear Information System (INIS)

Antoniadis, G.; Paraskevopoulos, K.M.; Bikiaris, D.; Chrissafis, K.

2010-01-01

A number of poly(ethylene terephthalate) (PET) nanocomposites were prepared by in situ polymerization using different amounts (0.5, 1, 2, 3 and 4 wt%) of fumed silica (SiO 2 ). The polymerization of PET was carried out by the two-stage melt polycondensation method. From DSC studies it was found that the melting point of the nanocomposites was shifted slightly to higher temperatures by the addition of SiO 2 till 3 wt% while for PET-4 wt% SiO 2 nanocomposite the melting point was reduced. As the amount of SiO 2 was increased the crystallization became faster, and there was, also, a shifting of the temperature of the crystallization peak to higher values, this being evidence that SiO 2 can act as nucleating agent. At higher content (3 and 4 wt%) the temperature of the crystallization peak is lower than that of PET-2 wt% SiO 2 due to the formation of crosslinked macromolecules. The activation energy is calculated with the Friedman's method. PET/SiO 2 samples present lower activation energy compared to that of neat PET, except those of PET-4% SiO 2 , in which the activation energy have a maximum value for α = 0.8 probably due to the second crystallization peak. Extensive crystallization studies by using Avrami, Ozawa and Malek methods verified that PET and its nanocomposites must be crystallized by two mechanisms with different activation energies taking place in different degrees of crystallization.

A study of the adsorption activities of silanol surface structures on a fused silica model substrate by combining 29Si CP MAS NMR and inverse gas chromatographic data

NARCIS (Netherlands)

Scholten, A.B.; Janssen, J.G.M.; Haan, de J.W.; Cramers, C.A.

1994-01-01

The possibilities of inverse gas-solid chromatog. (IGC) in obtaining chromatog. data on fumed silica were examd. Aerosil A-200, a fused silica model substrate in 29Si NMR anal., was trimethylsilylated to different degrees. IGC was used to vary reproducibly det. the free specific energies of

Re-use of incinerated agro-industrial waste as pozzolanic addition. Comparison with spanish silica fume

Directory of Open Access Journals (Sweden)

Delgado, A.

2009-12-01

Full Text Available This study attempted to determine the viability of using incinerated agro-industrial waste, ashes C1 and C2, as possible artificial pozzolanic additions in traditional and highperformance concretes and mortars, mainly, and for this reason, a comparative study was likewise conducted with Spanish silica fume (HS. The conclusion drawn from the findings was that the two ashes used could be regarded to be centainly, silicic artificial pozzolanic additions but only C2, which had a higher SiO2 content, could be regarded to be a “microsilica”, however, because its loss on ignition, L.O.I., fell within the acceptable range of variability. In contrast, C1 could not be so regarded because its L.O.I. was too high, despite its higher reactive silica SiO2r- content. For this reason, ash C1 had to be ruled out for any of the proposed uses, even though in terms of chemical and sulfatic characterization it was closer to HS than C2. By contrast, the mechanical strength values of C2 and HS were comparable, making the former initially acceptable for any of such uses. Finally, it has also been justified that, adoption of any method of trial to determine potential resistance to the sulfates of the Portland cements with calcareous filler lacks of sense.Este trabajo ha tenido por objetivo determinar la viabilidad de uso de dos residuos agroindustriales incinerados, cenizas C1 y C2, como posibles adiciones puzolánicas artificiales, para fabricar cementos y/o de sus productos derivados, hormigones y morteros tradicionales y especiales, principalmente; de aquí su estudio comparativo con el humo de sílice español, HS. Y la conclusión que se obtuvo fue que las dos cenizas pueden ser consideradas como adiciones puzolánicas artificiales con carácter químico silícico cierto, pero sólo una, la C2, podría llegar a ser considerada como “microsílice”, porque su pérdida por calcinación se encuentra dentro de su límite permitido. En cambio la C1, no, porque

A preliminary study of the relation between adsorption and CP-MAS-NMR characteristics of fused silica model substrates

NARCIS (Netherlands)

Scholten, A.B.; Janssen, J.G.M.; Haan, de J.W.; Cramers, C.A.M.G.; Sandra, P.J.F.; Devos, G.; Sandra, P.

1993-01-01

The fumed silica model substrate Aerosil was trimethylsilylated to different extents and studied by the combination of IGC and 29Si CP-MAS-NMR. Dihydroxydisiloxane groups were shown to be chemically more reactive than monohydroxytrisiloxane groups. Chromatographic experiments showed that these

Silica-Polystyrene Nanocomposite Particles Synthesized by Nitroxide-Mediated Polymerization and Their Encapsulation through Miniemulsion Polymerization

Directory of Open Access Journals (Sweden)

Bérangère Bailly

2006-01-01

Full Text Available Polystyrene (PS chains with molecular weights comprised between 8000 and 64000 g⋅mol-1 and narrow polydispersities were grown from the surface of silica nanoparticles (Aerosil A200 fumed silica and Stöber silica, resp. through nitroxide-mediated polymerization (NMP. Alkoxyamine initiators based on N-tert-butyl-1-diethylphosphono-2,2-dimethylpropyl nitroxide (DEPN and carrying a terminal functional group have been synthesized in situ and grafted to the silica surface. The resulting grafted alkoxyamines have been employed to initiate the growth of polystyrene chains from the inorganic surface. The maximum grafting density of the surface-tethered PS chains was estimated and seemed to be limited by initiator confinement at the interface. Then, the PS-grafted Stöber silica nanoparticles were entrapped inside latex particles via miniemulsion polymerization. Transmission electron microscopy indicated the successful formation of silica-polystyrene core-shell particles.

Nano-silica as the go material on heat resistant tunnel lining

Science.gov (United States)

Omar, Faizah; Osman, S. A.; Mutalib, A.

2018-04-01

This paper is concerned with passive fire protection method of protective concrete mix that is made up of fly ash, polypropylene fibre, and nano-silica. Nano-silica is focused on as the innovative material to be used in the composition of the protective concrete mix. The previous experimental studies which analyse the performance of passive fire protection on tunnels are discussed. This paper also discusses passive fire protection. The fire protection materials and behaviour analyses of tunnel structure are also presented. At the end of the paper, the recommendation of the optimum composition concrete material with fly ash, polypropylene fibre and nano-silica as tunnel lining fire protective materials is proposed.

Effects of nano-silica on mechanical performance and microstructure of ultra-high performance concrete

Energy Technology Data Exchange (ETDEWEB)

Mendes, T. M., E-mail: thiagomendes@utfpr.edu.br [Universidade Tecnologica Federal do Parana (UTFPR), Londrina, PR (Brazil). Departamento de Engenharia Ambiental; Repette, W.L., E-mail: wellington.repette@gmail.br [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Civil; Reis, P.J., E-mail: pjlondrina@yahoo.com.br [Univeridade Estadual de Londrina (UEL), PR (Brazil). Lab. de Fisica Nuclear Aplicada

2017-07-15

The use of nanoparticles in ultra-high strength concretes can result in a positive effect on mechanical performance of these cementitious materials. This study evaluated mixtures containing 10 and 20 wt% of silica fume, for which the optimum nano-silica content was determined, i.e. the quantity of nano-silica that resulted on the higher gain of strength. The physical characterization of raw materials was done in terms of particle size distribution, density and specific surface area. Chemical and mineralogical compositions of materials were obtained through fluorescence and X-ray diffraction. The mechanical performance was evaluated by compressive strength, flexural strength and dynamic elastic modulus measurements. The microstructural analysis of mixtures containing nano-silica was performed by X-ray diffraction, thermogravimetry, mercury intrusion porosimetry and scanning electron microscopy. Obtained results indicate an optimum content of nano-silica of 0.62 wt%, considering compressive and flexural strengths. This performance improvement was directly related to two important microstructural aspects: the packing effect and pozzolanic reaction of nano-silica. (author)

Effects of nano-silica on mechanical performance and microstructure of ultra-high performance concrete

International Nuclear Information System (INIS)

Mendes, T. M.; Repette, W.L.; Reis, P.J.

2017-01-01

The use of nanoparticles in ultra-high strength concretes can result in a positive effect on mechanical performance of these cementitious materials. This study evaluated mixtures containing 10 and 20 wt% of silica fume, for which the optimum nano-silica content was determined, i.e. the quantity of nano-silica that resulted on the higher gain of strength. The physical characterization of raw materials was done in terms of particle size distribution, density and specific surface area. Chemical and mineralogical compositions of materials were obtained through fluorescence and X-ray diffraction. The mechanical performance was evaluated by compressive strength, flexural strength and dynamic elastic modulus measurements. The microstructural analysis of mixtures containing nano-silica was performed by X-ray diffraction, thermogravimetry, mercury intrusion porosimetry and scanning electron microscopy. Obtained results indicate an optimum content of nano-silica of 0.62 wt%, considering compressive and flexural strengths. This performance improvement was directly related to two important microstructural aspects: the packing effect and pozzolanic reaction of nano-silica. (author)

Influence of high volumes of ultra-fine additions on self-compacting concrete[ACI SP-239

Energy Technology Data Exchange (ETDEWEB)

Cioffi, R. [Naples Univ., Naples (Italy). Faculty of Engineering; Colangelo, F. [Naples Univ., Naples (Italy). Dept. of Technologies; Caputo, D.; Liguori, B. [Naples Univ., Naples (Italy). Dept. of Materials and Production Engineering

2006-07-01

The addition of fine minerals can reduce water demand and increase the slump characteristics of concrete. This paper examined the influence of high volumes of ultra-fine fly ash, raw fly ash, silica fume and natural zeolites on the properties of self-compacting concrete (SCC). Three samples of SCC were prepared using various mineral additions to determine normal slump and J-ring slump flows of fresh concrete as well as the compressive strength and elastic modulus properties of hardened concrete. Cement and crushed limestone natural aggregates were used. The fly ash, silica fume and natural zeolites were subjected to wet high energy milling. The rotating speed, milling time, water-to-solid ratio, and size of milling media were optimized to obtain powders with varying qualities. Results of the study showed that values for the normal slump flow ranged between 604 and 785 mm, while the differences with the J-ring slump flow were less than 30 mm. The samples were then tested to evaluate the mechanical properties of the hardened concrete after 7 and 28 curing days. The modulus of elasticity and compressive strength showed improvements in the concretes containing the ultra-fine fly ash. No segregation phenomena were observed in the case of the cylindrical column specimens. It was concluded that all the specimens provided environmentally sustainable, high workability concretes which can be successfully prepared with the addition of high volumes of minerals. 17 refs., 5 tabs., 6 figs.

In vitro effects of cisplatin-functionalized silica nanoparticles on chondrocytes

Energy Technology Data Exchange (ETDEWEB)

Bhowmick, Tridib Kumar; Yoon, Diana [University of Maryland, Department of Chemical and Biomolecular Engineering (United States); Patel, Minal; Fisher, John [University of Maryland, Fischell Department of Bioengineering (United States); Ehrman, Sheryl, E-mail: sehrman@umd.ed [University of Maryland, Department of Chemical and Biomolecular Engineering (United States)

2010-10-15

In this study, we evaluated the combined effect of a known toxic molecule, cisplatin, in combination with relatively nontoxic nanoparticles, amorphous fumed silica, on chondrocyte cells. Cisplatin was attached to silica nanoparticles using aminopropyltriethoxy silane as a linker molecule, and characterized in terms of size, shape, specific surface area, as well as the dissolution of cisplatin from the silica surface. The primary particle diameter of the as-received silica nanoparticles ranged from 7.1 to 61 nm, estimated from measurements of specific surface area, and the primary particles were aggregated. The effects of cisplatin-functionalized silica particles with different specific surface areas (41, 85, 202, 237, and 297 m{sup 2}/g) were compared in vitro on chondrocytes, the parenchymal cell of hyaline cartilage. The results show that adverse effects on cell function, as evidenced by reduced metabolic activity measured by the MTT assay and increased membrane permeability observed using the Live/Dead stain, can be correlated with specific surface area of the silica. Cisplatin-functionalized silica nanoparticles with the highest specific surface area incited the greatest response, which was almost equivalent to that induced by free cisplatin. This result suggests the importance of particle specific surface area in interactions between cells and surface-functionalized nanomaterials.

In vitro effects of cisplatin-functionalized silica nanoparticles on chondrocytes

Science.gov (United States)

Bhowmick, Tridib Kumar; Yoon, Diana; Patel, Minal; Fisher, John; Ehrman, Sheryl

2010-10-01

In this study, we evaluated the combined effect of a known toxic molecule, cisplatin, in combination with relatively nontoxic nanoparticles, amorphous fumed silica, on chondrocyte cells. Cisplatin was attached to silica nanoparticles using aminopropyltriethoxy silane as a linker molecule, and characterized in terms of size, shape, specific surface area, as well as the dissolution of cisplatin from the silica surface. The primary particle diameter of the as-received silica nanoparticles ranged from 7.1 to 61 nm, estimated from measurements of specific surface area, and the primary particles were aggregated. The effects of cisplatin-functionalized silica particles with different specific surface areas (41, 85, 202, 237, and 297 m2/g) were compared in vitro on chondrocytes, the parenchymal cell of hyaline cartilage. The results show that adverse effects on cell function, as evidenced by reduced metabolic activity measured by the MTT assay and increased membrane permeability observed using the Live/Dead stain, can be correlated with specific surface area of the silica. Cisplatin-functionalized silica nanoparticles with the highest specific surface area incited the greatest response, which was almost equivalent to that induced by free cisplatin. This result suggests the importance of particle specific surface area in interactions between cells and surface-functionalized nanomaterials.

Immobilization of cesium in cement containing reactive silica and pozzolans

International Nuclear Information System (INIS)

McCulloch, C.E.; Angus, M.J.; Glasser, F.P.; Rahman, A.A.

1984-01-01

High surface area silicas, ground blast furnace slag, fly ash, and natural pozzolan markedly enhance the sorption of Cs in cement-based systems. Fly ash low in alkali and silicas are considered to be most suitable for Cs immobilization. Since these materials are chemically reactive with the cement components, the optimal level of addition must be sufficiently high, probably 20-30 wt%, to provide a permanent excess of sorbent. The sorptive mechanism is demonstrated and shown to be enhanced by the alkaline cement environment

Improved concrete properties to resist the saline water using environmental by-product

Directory of Open Access Journals (Sweden)

Mohamed Anwar

2013-10-01

Full Text Available This paper investigates the influence of using environmental by-product materials (silica fume and fly ash in concrete on the chloride ion permeability of concrete. Nine concrete mixtures were designed to have the same degree of workability and air content with water/cementitious material ratio of 0.4. The studied parameters include the main fresh and hardened concrete properties such as slump, air content, unit weight, compressive strength, tensile strength, flexural strength, static Young's modulus, and dynamic elastic modulus. Concrete samples were kept in water for 28 days, then immersed in artificial sea water for 5 months. The total and soluble chloride contents were measured through the concrete using the potentiometric titration analysis. The obtained test results indicated that the use of ternary systems in concrete improved the different characteristics of the product concrete and showed a significant resistance to chloride penetration. The weights of chloride in mix 9 (10% silica fume and 25% fly ash at depths from the concrete surface to 30 mm were less than the weights of control mix 1 (100% ordinary Portland cement by about 60%. Further, the ternary systems can be used in concrete industry with considerable proportions.

The macro- and micro properties of cement pastes with silica-rich materials cured by wet-mixed steaming injection

International Nuclear Information System (INIS)

Wu, D.S.; Peng, Y.N.

2003-01-01

This research used cement pastes with a low water/blaine ratio (W/b=0.27). Rice husk ashes (RHA) burned at 700 and 850 deg. C, silica fume, silica sand (Ottawa standard sand), etc., were the added ingredients. Wet-mixed steam injection (WMSI) was at five different temperatures: 65, 80, 120, 150 and 180 deg. C. We investigated cement pastes with added silica-rich materials. For different WMSI temperatures and times, we explored the relations between compressive strength, hydration products, and pozzolanic reaction mechanism. From scanning electron microscopy (SEM) and EDS, we know that hydration products become very complicated, depending on the WMSI temperatures and times. It is difficult to determine the direct effects on the strength based on changes in the products. Experimental results, however, clearly showed that the compressive strength was worst for 80 deg. C and best for 180 deg. C. High-temperature WMSI is best with 4-h presteaming period and 8-h retention time. Curing in saturated limewater for 28 days did not increase the strength. The three types of silica-rich materials used in this research all participated in the reaction during high-temperature WMSI; they helped to increase the strength. Addition of Ottawa standard sand resulted in the best strength, followed by addition of RHA, while addition of silica fume was worse than the others. Specimens treated with high-temperature WMSI would swell slightly if they were placed in air. This was different from normal-temperature curing

The silica fume on the production of resistant

International Nuclear Information System (INIS)

Liborio, J.B.L.; Melo, A.B. de; Souza, M.F. de; Silva, I.J. da

1998-01-01

New developments in the field of the materials science and engineering have resulted in news technologies for protection of concrete made of Portland cement. The final product associates higher durability to very high mechanical resistance. Concrete is a material that presents a random distribution of types and sizes of pores. This porosity not just implies in differences in the mechanical properties but it also affect the permeability, allowing the movement of possible fluids that can degrade partially or totally the concrete. The active silica addition of high pozzolanics provides to concrete significant improvements turning it most compact, with smaller numbers of intercommunicated pores and, therefore, resistance to several aggressiveness sources and a material of high performance. This paper discuss the potential applications of the high performance concrete and the expectations for its currents use in the civil construction. (author)

Dry fumes purifying system using anhydrous baking soda; Procede chimique d`epuration des fumees au bicarbonate de soude anhydre

Energy Technology Data Exchange (ETDEWEB)

Anon.

1998-04-01

UNISYSTEMS has developed the industrial implementation of the chemical process using anhydrous backing soda, patented by SOLVAY, for purifying fumes containing inorganic salts and sulphur oxides as polluting agents. The system can be applied to industrial processes releasing this type of polluting agents in the fumes at a temperature over 160 deg C, as it is specially indicated in purifying fumes coming from ceramic firing kilns. (authors)

Alkali silica reaction (ASR) in cement free alkali activated sustainable concrete.

Science.gov (United States)

2016-12-19

This report summarizes the findings of an experimental evaluation into alkali silica : reaction (ASR) in cement free alkali-activated slag and fly ash binder concrete. The : susceptibility of alkali-activated fly ash and slag concrete binders to dele...

29-Silicon NMR evidence for the improved chromatographic siloxane bond stability of bulky alkylsilane ligands on a silica surface

NARCIS (Netherlands)

Scholten, A.B.; Haan, de J.W.; Claessens, H.A.; Ven, van de L.J.M.; Cramers, C.A.

1994-01-01

A stable bond stationary phase for reversed-phase HPLC, with a diisobutyl-n-octadecylsilane derivatized surface, was studied using 29Si CPMAS NMR. Fumed silica surfaces (Aerosil), trimethylsilylated to different extents, were used to illustrate the effect of ligand surface loading on the hydrogen

Silica micro- and nanoparticles reduce the toxicity of surfactant solutions.

Science.gov (United States)

Ríos, Francisco; Fernández-Arteaga, Alejandro; Fernández-Serrano, Mercedes; Jurado, Encarnación; Lechuga, Manuela

2018-04-20

In this work, the toxicity of hydrophilic fumed silica micro- and nanoparticles of various sizes (7 nm, 12 nm, and 50 μm) was evaluated using the luminescent bacteria Vibrio fischeri. In addition, the toxicity of an anionic surfactant solution (ether carboxylic acid), a nonionic surfactant solution (alkyl polyglucoside), and a binary (1:1) mixture of these solutions all containing these silica particles was evaluated. Furthermore, this work discusses the adsorption of surfactants onto particle surfaces and evaluates the effects of silica particles on the surface tension and critical micellar concentration (CMC) of these anionic and nonionic surfactants. It was determined that silica particles can be considered as non-toxic and that silica particles reduce the toxicity of surfactant solutions. Nevertheless, the toxicity reduction depends on the ionic character of the surfactants. Differences can be explained by the different adsorption behavior of surfactants onto the particle surface, which is weaker for nonionic surfactants than for anionic surfactants. Regarding the effects on surface tension, it was found that silica particles increased the surface activity of anionic surfactants and considerably reduced their CMC, whereas in the case of nonionic surfactants, the effects were reversed. Copyright © 2018 Elsevier B.V. All rights reserved.

Investigation of the temperature effect on electrochemical behaviors of TiO2 for gel type valve regulated lead-acid batteries

Directory of Open Access Journals (Sweden)

Metin GENÇTEN

2016-12-01

Full Text Available In this study, the effect of temperature on the electrochemical behaviors of gel electrolyte systems was investigated for valve regulated lead-acid battery at 0≤ T ≤50 oC. Fumed silica and mixture of fumed silica and TiO2 were used as gel electrolytes. TiO2 has a good combination with fumed silica. They were characterized by cyclic voltammetry, electrochemical impedance spectroscopy and battery tests. The anodic peak currents and redox capacities of the gel electrolytes increased with increasing of temperature. The highest anodic peak current and redox capacity were observed at 30 oC in fumed silica and at 40 oC in fumed silica:TiO2 based gel systems. The solution and charge transfer resistance values decreased in fumed silica:TiO2 gel system by increasing temperature. In battery tests, discharge curves were obtained for each gel system at 0, 25 and 50 oC. The discharge time of mixture gel electrolyte system was higher than that of fumed silica based gel electrolyte at low (0 oC and high (50 oC temperatures. The best performance was obtained in fumed silica based gel electrolyte at 25 oC.

Laboratory Investigation on Compressive Strength and Micro-structural Features of Foamed Concrete with Addition of Wood Ash and Silica Fume as a Cement Replacement

Directory of Open Access Journals (Sweden)

Othuman Mydin M.A.

2014-01-01

Full Text Available Wood Ash (WA and Silica Fume (SF exhibit good cementation properties and have great potential as supplementary binder materials for the concrete production industry. This study will focus on enhancing the micro-structural formation and compressive strength of foamed concrete with the addition of WA and SF. A total of 3 mixes were prepared with the addition of WA and SF at various cement replacement levels by total binder weight. For this particular study, the combination of WA (5%, 10%, and 15% by binder weight and SF (5%, 10%, and 15% by binder weight were utilized as supplementary binder materials to produce foamed concrete mixes. As was made evident from micrographs obtained in the study, the improvement observed in the compressive strength of the foamed concrete was due to a significant densification in the microstructure of the cement paste matrix in the presence of WA and SF hybrid supplementary binders. Experimental results indicated that the combination of 15% SF and 5% WA by binder weight had a more substantial influence on the compressive strength of foamed concrete compared to the control mix. Furthermore, the addition of WA and SF significantly prolonged the setting times of the blended cement paste of the foamed concrete.

[Analysis on oil fume particles in catering industry cooking emission].

Science.gov (United States)

Tan, De-Sheng; Kuang, Yuan-Cheng; Liu, Xin; Dai, Fei-Hong

2012-06-01

By measuring the particulate matter of oil fume which is over 10 microm or below 10 microm separately and using microradiography and Electrical Low Pressure Impactor (ELPI), it is found out the distributing characteristic of oil fume particles in catering industry cooking emission. The result shows that the diameter of the oil fume particles which was sedimentated in the kitchen is between 10-400 microm, the concentration peak value is between 10-100 microm. The diameter of oil fume aerosol is mostly smaller than 1 microm, while the concentration peak value is between 0.063-0.109 microm. In addition, the mass concentration peak value is between 6.560-9.990 microm. Through the analysis to the physical characteristics of oil fume from catering industry cooking emissions, the eigenvalue of the oil fume has been found and the feature matter for monitoring the oil fume has been discovered to provide a reasonable standard for controlling and monitoring the catering industry cooking emission.

Health hazards due to the inhalation of amorphous silica

Energy Technology Data Exchange (ETDEWEB)

Merget, R.; Bruening, T. [Research Institute for Occupational Medicine (BGFA), Bochum (Germany); Bauer, T. [Bergmannsheil, University Hospital, Department of Internal Medicine, Division of Pneumonology, Allergology and Sleep Medicine, Bochum (Germany); Kuepper, H.U.; Breitstadt, R. [Degussa-Huels Corp., Wesseling (Germany); Philippou, S. [Department of Pathology, Augusta Krankenanstalten, Bochum (Germany); Bauer, H.D. [Research Institute for Hazardous Substances (IGF), Bochum (Germany)

2002-01-01

Occupational exposure to crystalline silica dust is associated with an increased risk for pulmonary diseases such as silicosis, tuberculosis, chronic bronchitis, chronic obstructive pulmonary disease (COPD) and lung cancer. This review summarizes the current knowledge about the health effects of amorphous (non-crystalline) forms of silica. The major problem in the assessment of health effects of amorphous silica is its contamination with crystalline silica. This applies particularly to well-documented pneumoconiosis among diatomaceous earth workers. Intentionally manufactured synthetic amorphous silicas are without contamination of crystalline silica. These synthetic forms may be classified as (1) wet process silica, (2) pyrogenic (''thermal'' or ''fumed'') silica, and (3) chemically or physically modified silica. According to the different physico-chemical properties, the major classes of synthetic amorphous silica are used in a variety of products, e.g. as fillers in the rubber industry, in tyre compounds, as free-flow and anti-caking agents in powder materials, and as liquid carriers, particularly in the manufacture of animal feed and agrochemicals; other uses are found in toothpaste additives, paints, silicon rubber, insulation material, liquid systems in coatings, adhesives, printing inks, plastisol car undercoats, and cosmetics. Animal inhalation studies with intentionally manufactured synthetic amorphous silica showed at least partially reversible inflammation, granuloma formation and emphysema, but no progressive fibrosis of the lungs. Epidemiological studies do not support the hypothesis that amorphous silicas have any relevant potential to induce fibrosis in workers with high occupational exposure to these substances, although one study disclosed four cases with silicosis among subjects exposed to apparently non-contaminated amorphous silica. Since the data have been limited, a risk of chronic bronchitis, COPD or

Health hazards due to the inhalation of amorphous silica

International Nuclear Information System (INIS)

Merget, R.; Bruening, T.; Bauer, T.; Kuepper, H.U.; Breitstadt, R.; Philippou, S.; Bauer, H.D.

2002-01-01

Occupational exposure to crystalline silica dust is associated with an increased risk for pulmonary diseases such as silicosis, tuberculosis, chronic bronchitis, chronic obstructive pulmonary disease (COPD) and lung cancer. This review summarizes the current knowledge about the health effects of amorphous (non-crystalline) forms of silica. The major problem in the assessment of health effects of amorphous silica is its contamination with crystalline silica. This applies particularly to well-documented pneumoconiosis among diatomaceous earth workers. Intentionally manufactured synthetic amorphous silicas are without contamination of crystalline silica. These synthetic forms may be classified as (1) wet process silica, (2) pyrogenic (''thermal'' or ''fumed'') silica, and (3) chemically or physically modified silica. According to the different physico-chemical properties, the major classes of synthetic amorphous silica are used in a variety of products, e.g. as fillers in the rubber industry, in tyre compounds, as free-flow and anti-caking agents in powder materials, and as liquid carriers, particularly in the manufacture of animal feed and agrochemicals; other uses are found in toothpaste additives, paints, silicon rubber, insulation material, liquid systems in coatings, adhesives, printing inks, plastisol car undercoats, and cosmetics. Animal inhalation studies with intentionally manufactured synthetic amorphous silica showed at least partially reversible inflammation, granuloma formation and emphysema, but no progressive fibrosis of the lungs. Epidemiological studies do not support the hypothesis that amorphous silicas have any relevant potential to induce fibrosis in workers with high occupational exposure to these substances, although one study disclosed four cases with silicosis among subjects exposed to apparently non-contaminated amorphous silica. Since the data have been limited, a risk of chronic bronchitis, COPD or emphysema cannot be excluded. There is no

Alkali content of fly ash : measuring and testing strategies for compliance : [tech transfer summary].

Science.gov (United States)

2015-04-01

This study investigated the test methods used to determine the : alkali content of fly ash. It also evaluated if high-alkali fly ash : exacerbates alkali-silica reaction in laboratory tests and field : concrete.

Experimental Study on the Characteristics of Polymer Concrete With Epoxy Resin

Directory of Open Access Journals (Sweden)

Maria Harja Ioniţă

2008-01-01

Full Text Available In the paper are presented the results of some experimental researches concerning polymer mortars and concretes realized of epoxy resin, silica fume and crushed aggregates. The mechanical characteristics of hardened concrete were determined. The silica fume content varied between 6.5% and 30% to polymer mortar and 6.4% and 9.6% to polymer concrete. The obtained results show maximum characteristics for a dosage of 24% resin and maximum dosage of silica fume to the polymer mortar, and for the polymer concrete the mechanical characteristics are influenced by all mixture factors: the compressive strength increases with the increase of silica fume dosage, and the flexure strength and split strength increase with the decreasing of silica fume dosage.

Thermal insulator made of ultra fine particles of silica. Chobiryushi silica kei dannetsuzai

Energy Technology Data Exchange (ETDEWEB)

Eguchi, T.

1991-05-30

An overview was presented of properties and applications of thermal insulator made of ultra fine powder of silica, MICROTHERM. The thermal conductivity of MICROTHERM is as low as (1/3) - (1/4) of that of conventional thermal insulator, because it is mainly composed of fumed silica or aero gel and formed into porous structure. In addition, metal oxide of special particle size is added to it in order to reject the radiative heat. The thermal insulation property and the mechanical strength of MICROTHERM is not affected by a sudden change in temperature and moisture. The standard type of MICROTHERM can be used at a temperature up to 950 {degree}C, while the high temperature type MICROTHERM can stand a high temperature up to 1025 {degree}C for long period of time. The thickness of insulator can be reduced markedly by using MICROTHERM as compared with the use of conventional insulating materials. Many new products in which MICROTHERM is used came into market. New type kilt, Semi-cylindrical block, Super high temperature MICROTHERM are just a few examples. Variety of application and energy saving effect are attracting public attention. 11 figs.

Mechanical properties of high-strength concrete

Science.gov (United States)

Mokhtarzadeh, Alireza

This report summarizes an experimental program conducted to investigate production techniques and mechanical properties of high strength concrete in general and to provide recommendations for using these concretes in manufacturing precast/prestressed bridge girders. Test variables included total amount and composition of cementitious material (portland cement, fly ash, and silica fume), type and brand of cement, type of silica fume (dry densified and slurry), type and brand of high-range water-reducing admixture, type of aggregate, aggregate gradation, maximum aggregate size, and curing. Tests were conducted to determine the effects of these variables on changes in compressive strength and modulus of elasticity over time, splitting tensile strength, modulus of rupture, creep, shrinkage, and absorption potential (as an indirect indicator of permeability). Also investigated were the effects of test parameters such as mold size, mold material, and end condition. Over 6,300 specimens were cast from approximately 140 mixes over a period of 3 years.

Effect of mechanical activation of fly ash added to Moroccan Portland cement

Directory of Open Access Journals (Sweden)

Ez-zaki H.

2018-01-01

This study aims to investigate the influence of grinding fly ash on the physico-chemical and mechanical properties of fly ash blended CPJ45 cement. The addition of the fly ash particles to the grinder leads respectively to the breakage of the particles and to reduce the agglomeration effect in the balls of cement grinder. Fly ash milling was found to improve particles fineness, and increase the silica and alumina content in the cement. Furthermore, milled fly ash blended cements show higher compressive strength compared to unmilled fly ash blended cements, due to improved fly ash reactivity through their mechanical activation.

Analysis of polycyclic aromatic hydrocarbons in cooking oil fumes.

Science.gov (United States)

Li, S; Pan, D; Wang, G

1994-01-01

Various samples of cooking oil fumes were analyzed to an effort to study the relationship between the high incidence of pulmonary adenocarcinoma in Chinese women and cooking oil fumes in the kitchen. Polycyclic aromatic hydrocarbons (PAHs) in samples of cooking oil fumes were extracted, chromatographed, and measured by fluorescence spectrophotometer. The samples included oil fumes from three commercial cooking oils and fumes from three catering shops. All samples contained benzo(a)pyrene (BaP) and dibenzo (a,h)anthracene (DBahA). In addition, the concentration of DBahA was 5.7 to 22.8 times higher than that of BaP in the fume samples. Concentrations of BaP and DBahA were, respectively, 0.463 and 5.736 micrograms/g in refined vegetable oil, 0.341 and 3.725 micrograms/g in soybean oil, and 0.305 and 4.565 micrograms/g in vegetable oil. Investigation of PAH concentrations at three catering shops showed that the level of BaP at a Youtiao (deep-fried twisted dough sticks) shop was 4.18 micrograms/100 m3, 2.28 micrograms/100 m3 at a Seqenma (candied fritters) workshop, and 0.49 micrograms/100 m3 at a kitchen of a restaurant; concentrations of DBahA were 33.80, 14.41, and 3.03 micrograms/100 m3, respectively. The high concentration of carcinogens, such as BaP and DBahA, in cooking oil fumes might help explain why Chinese women, who spend more time exposed to cooking oil fumes than men, have a high incidence of pulmonary adenocarcinoma.

A study on the effect of nano silica on compressive strength of high volume fly ash mortars and concretes

International Nuclear Information System (INIS)

Shaikh, F.U.A.; Supit, S.W.M.; Sarker, P.K.

2014-01-01

Highlights: • The addition of NS compensates low early age compressive strength of HVFA system. • NS also contributes to later age compressive strength gain of HVFA system. • The XRD results confirm the reduction of CH in HVFA paste due to addition of NS. - Abstract: This paper presents the effect of nano silica (NS) on the compressive strength of mortars and concretes containing different high volume fly ash (HVFA) contents ranging from 40% to 70% (by weight) as partial replacement of cement. The compressive strength of mortars is measured at 7 and 28 days and that for concretes is measured at 3, 7, 28, 56 and 90 days. The effects of NS in microstructure development and pozzolanic reaction of pastes containing above HVFA contents are also studied through backscattered electron (BSE) image and X-ray diffraction (XRD) analysis. Results show that among different NS contents ranging from 1% to 6%, cement mortar containing 2% NS exhibited highest 7 and 28 days compressive strength. This NS content (2%) is then added to the HVFA mortars and concretes and the results show that the addition of 2% NS improved the early age (7 days) compressive strength of mortars containing 40% and 50% fly ash by 5% and 7%, respectively. However, this improvement is not observed at high fly ash contents beyond 50%. On the other hand, all HVFA mortars exhibited improvement in 28 days compressive strength due to addition of 2% NS and the most significant improvement is noticed in mortars containing more than 50% fly ash. In HVFA concretes, the improvement of early age (3 days) compressive strength is also noticed due to addition of 2% NS. The BSE and XRD analysis results also support the above findings

The effect of measuring procedure on the apparent rheological properties of self-compacting concrete

DEFF Research Database (Denmark)

Geiker, Mette Rica; Bradl, M.; Thrane, L.N.

2002-01-01

Torque versus time during testing of the rheological properties of fresh concrete has been investigated. The testing was performed in a BML viscometer and on a self-compacting concrete (w/c = 0.45, 70% rapid hardening Portland cement, 3% silica fume, 27% fly ash, third generation superplasticizer......, lack of steady state may explain the apparent shear-thickening behaviour of self-compacting concrete reported elsewhere. (C) 2002 Elsevier Science Ltd. All rights reserved....

Reduction of fume damage in forests: report on the symposium on fume damage held in Tharandt from 30th September to 2nd October 1965

Energy Technology Data Exchange (ETDEWEB)

Daessler, H G; Ranft, H

1967-01-01

Summaries are presented of 15 papers, including: extent of variation in fume resistance in Larix and problems of breeding for resistance (Schoenbach); results of research on fume damage on experimental areas in E. Germany (H. Enderlin) (noting differences in resistance to SO/sub 2/ damage of various species of Picea, Pinus, and Abies, varieties of Pseudotsuga taxifolia and provenances of Pinus contorta and Larix spp., effect of fertilizers on resistance, and mass selection of resistant planting stock in practice); resistance of Pinus omorika to fume damage (K.F. Wentzel); chemical and physiological studies on the metabolism of the assimilation organs of conifers affected by SO/sub 2/ (S. Boertitz); basic physiological and phenological studies on the preliminary selection of conifers for SO/sub 2/ resistance (M. Vogl); fertilizer trials in fume-damaged pine stands on Dueben Heath (H. Krauss); insect pests on young pine stands in fume-damaged regions in Poland (Z. Sierpinski); birch and alder pests in industrial regions (Z. Schnaider); management of young fume-damaged spruce stands (E. Pelz); effect of fumes from the potash industry on forest stands in East Germany (E. Ewert); the distribution of injurious substances in leaves (G. Halbwachs); emission of SO/sub 2/ absorbed by spruce needles (J. Materna); and estimating fume damage expected near future power stations (H. Lux).

Recovery of iron oxide from coal fly ash

Science.gov (United States)

Dobbins, Michael S.; Murtha, Marlyn J.

1983-05-31

A high quality iron oxide concentrate, suitable as a feed for blast and electric reduction furnaces is recovered from pulverized coal fly ash. The magnetic portion of the fly ash is separated and treated with a hot strong alkali solution which dissolves most of the silica and alumina in the fly ash, leaving a solid residue and forming a precipitate which is an acid soluble salt of aluminosilicate hydrate. The residue and precipitate are then treated with a strong mineral acid to dissolve the precipitate leaving a solid residue containing at least 90 weight percent iron oxide.

DURABILITY OF GREEN CONCRETE WITH TERNARY CEMENTITIOUS SYSTEM CONTAINING RECYCLED AGGREGATE CONCRETE AND TIRE RUBBER WASTES

Directory of Open Access Journals (Sweden)

MAJID MATOUQ ASSAS

2016-06-01

Full Text Available All over the world billions of tires are being discarded and buried representing a serious ecological threat. Up to now a small part is recycled and millions of tires are just stockpiled, landfilled or buried. This paper presents results about the properties and the durability of green concrete contains recycled concrete as a coarse aggregate with partial replacement of sand by tire rubber wastes for pavement use. Ternary cementious system, Silica fume, Fly ash and Cement Kiln Dust are used as partial replacement of cement by weight. Each one replaced 10% of cement weight to give a total replacement of 30%. The durability performance was assessed by means of water absorption, chloride ion permeability at 28 and 90 days, and resistance to sulphuric acid attack at 1, 7, 14 and 28 days. Also to the compression behaviors for the tested specimens at 7, 14, 28 and 90 days were detected. The results show the existence of ternary cementitious system, silica fly ash and Cement Kiln Dust minimizes the strength loss associated to the use of rubber waste. In this way, up to 10% rubber content and 30% ternary cementious system an adequate strength class value (30 MPa, as required for a wide range of common structural uses, can be reached both through natural aggregate concrete and recycled aggregate concrete. Results also show that, it is possible to use rubber waste up to 15% and still maintain a high resistance to acid attack. The mixes with 10%silica fume, 10% fly ash and 10% Cement Kiln Dust show a higher resistance to sulphuric acid attack than the reference mix independently of the rubber waste content. The mixes with rubber waste and ternary cementious system was a lower resistance to sulphuric acid attack than the reference mix.

Ultrafine portland cement performance

Directory of Open Access Journals (Sweden)

C. Argiz

2018-04-01

Full Text Available By mixing several binder materials and additions with different degrees of fineness, the packing density of the final product may be improved. In this work, ultrafine cement and silica fume mixes were studied to optimize the properties of cement-based materials. This research was performed in mortars made of two types of cement (ultrafine Portland cement and common Portland cement and two types of silica fume with different particle-size distributions. Two Portland cement replacement ratios of 4% and 10% of silica fume were selected and added by means of a mechanical blending method. The results revealed that the effect of the finer silica fume mixed with the coarse cement enhances the mechanical properties and pore structure refinement at a later age. This improvement is somewhat lower in the case of ultrafine cement with silica fume.

Two choices for the functionalization of silica nanoparticles with gallic acid: characterization of the nanomaterials and their antimicrobial activity against Paenibacillus larvae

Science.gov (United States)

Vico, Tamara A.; Arce, Valeria B.; Fangio, María F.; Gende, Liesel B.; Bertran, Celso A.; Mártire, Daniel O.; Churio, María S.

2016-11-01

Silica nanoparticles attached to gallic acid were synthesized from 7-nm diameter fumed silica particles by different functionalization methods involving the condensation of hydroxyl or carboxyl groups. The particles were characterized by thermal analyses and UV-vis, FTIR, NMR, and EPR spectroscopies. In comparison to free gallic acid, enhanced stability and increased antimicrobial activity against Paenibacillus larvae were found for the functionalized nanoparticles. Thus, both derivatization strategies result in improved properties of the natural polyphenol as antimicrobial agent for the treatment of honeybee pathologies.

Two choices for the functionalization of silica nanoparticles with gallic acid: characterization of the nanomaterials and their antimicrobial activity against Paenibacillus larvae

International Nuclear Information System (INIS)

Vico, Tamara A.; Arce, Valeria B.; Fangio, María F.; Gende, Liesel B.; Bertran, Celso A.; Mártire, Daniel O.; Churio, María S.

2016-01-01

Silica nanoparticles attached to gallic acid were synthesized from 7-nm diameter fumed silica particles by different functionalization methods involving the condensation of hydroxyl or carboxyl groups. The particles were characterized by thermal analyses and UV–vis, FTIR, NMR, and EPR spectroscopies. In comparison to free gallic acid, enhanced stability and increased antimicrobial activity against Paenibacillus larvae were found for the functionalized nanoparticles. Thus, both derivatization strategies result in improved properties of the natural polyphenol as antimicrobial agent for the treatment of honeybee pathologies.

Two choices for the functionalization of silica nanoparticles with gallic acid: characterization of the nanomaterials and their antimicrobial activity against Paenibacillus larvae

Energy Technology Data Exchange (ETDEWEB)

Vico, Tamara A. [Universidad Nacional de Mar del Plata, Departamento de Química, FCEyN/IFIMAR, CONICET (Argentina); Arce, Valeria B. [CONICET La Plata—CIC—UNLP, Centro de Investigaciones Ópticas (CIOp) (Argentina); Fangio, María F., E-mail: mfangio@mdp.edu.ar [Universidad Nacional de Mar del Plata, Departamento de Química, FCEyN/IFIMAR, CONICET (Argentina); Gende, Liesel B. [Universidad Nacional de Mar del Plata, Centro de Investigaciones en Abejas Sociales, FCEyN (Argentina); Bertran, Celso A. [University of Campinas, Chemistry Institute (Brazil); Mártire, Daniel O. [Universidad Nacional de La Plata, Instituto de Investigaciones Fisicoquímicas Teóricas y Aplicadas (INIFTA), CONICET (Argentina); Churio, María S., E-mail: schurio@mdp.edu.ar [Universidad Nacional de Mar del Plata, Departamento de Química, FCEyN/IFIMAR, CONICET (Argentina)

2016-11-15

Silica nanoparticles attached to gallic acid were synthesized from 7-nm diameter fumed silica particles by different functionalization methods involving the condensation of hydroxyl or carboxyl groups. The particles were characterized by thermal analyses and UV–vis, FTIR, NMR, and EPR spectroscopies. In comparison to free gallic acid, enhanced stability and increased antimicrobial activity against Paenibacillus larvae were found for the functionalized nanoparticles. Thus, both derivatization strategies result in improved properties of the natural polyphenol as antimicrobial agent for the treatment of honeybee pathologies.

Interlaboratory comparison on 137Cs activity concentration in fume dust

International Nuclear Information System (INIS)

Tzika, Faidra; Hult, Mikael; Burda, Oleksiy; Arnold, Dirk; Sibbens, Goedele; Caro Marroyo, Belén; Gómez–Mancebo, Maria Belén; Peyrés, Virginia; Moser, Hannah; Ferreux, Laurent; Šolc, Jaroslav; Dryák, Pavel; Fazio, Aldo; Luca, Aurelian; Vodenik, Branko; Reis, Mario

2015-01-01

A comparison was conducted, between 11 European National Metrology Institutes and EC-JRC, on measurement of 137 Cs activity concentration in fume dust. As test material an activity standard produced from real contaminated fume dust was used. The standard material consisted of 13 cylindrical samples of compressed fume dust. The material contained 137 Cs and 60 Co of reference activity concentrations of (9.72±0.10) Bq/g and (0.450±0.018) Bq/g, respectively, for the reference date of 1 June 2013, determined using the comparison results. The organization and results of the intercomparison, as well as the process of obtaining reliable reference values are presented. - Highlights: • A European comparison was conducted on measurement of 137 Cs activity in fume dust. • Participants used high resolution gamma ray spectrometry. • Efficiency calibration included Monte Carlo, numerical and experimental methods. • Reference 137 Cs and 60 Co activity concentrations in the fume dust were determined. • A new traceable activity standard of fume dust matrix is available to end-users.

Development of low-pH cementitious materials for HLRW repositories. Resistance against ground waters aggression

OpenAIRE

Garcia Calvo, Jose Luis; Hidalgo, A.; Fernandez Luco, L.; Alonso Alonso, Maria Cruz

2010-01-01

One of the most accepted engineering construction concepts of underground repositories for high radioactive waste considers the use of low-pH cementitious materials. This paper deals with the design of those based on Ordinary Portland Cements with high contents of silica fume and/or fly ashes that modify most of the concrete “standard” properties, the pore fluid composition and the microstructure of the hydrated products. Their resistance to long-term groundwater aggression is also evaluated....

Concrete Durability: A Multibillion-Dollar Opportunity

Science.gov (United States)

1987-01-01

Superplasticizers 19. ABSTRACT (Coninue an mwsre if mceonay uW-6dentify by block number) Concrete industry practices today fail to take advantage of the many...concrete are very much reduced by incorporating silica fume or slag in appropriately large proportions and are also somewhat reduced by fly ash and...some cases to internal "self-desiccation* by hydration. Most of the pore spaces will refill readily when the concrete is revetted , because of the partial

Non-destructive analysis of chlorine in fly ash cement concrete

International Nuclear Information System (INIS)

Naqvi, A.A.; Garwan, M.A.; Nagadi, M.M.; Maslehuddin, M.; Al-Amoudi, O.S.B.; Khateeb-ur-Rehman

2009-01-01

Preventive measures against reinforcement corrosion in concrete require increasing concrete density to prevent the diffusion of chloride ions to the steel surface. Pozzolanic materials, such as fly ash (FA), silica fume (SF), and blast furnace slag (BFS) are added to concrete to increase its density. Monitoring the chloride concentration in concrete is required to assess the chances of reinforcement corrosion. In this study, FA was added to Portland cement concrete to increase its density. Prompt gamma neutron activation analysis (PGNAA) technique was utilized to analyze the concentration of chlorine in concrete. The chlorine concentration in the FA cement concrete was evaluated by determining the yield of 1.16, 1.95, 6.11, 6.62, 7.41, 7.79, and 8.58 MeV gamma-rays of chlorine from the FA concrete specimen containing 0.4-3.5 wt% chlorine. An excellent agreement was noted between the experimental yield of the prompt gamma-rays and the calculated yield obtained through the Monte Carlo simulations. The Minimum Detectable Concentration (MDC) of chlorine in FA cement concrete was also calculated. The best value of MDC limit of chlorine in the FA cement concrete was found to be 0.022±0.007 and 0.038±0.017 wt% for 1.16 and 6.11 MeV prompt gamma-rays, respectively. Within the statistical uncertainty, the lower bound of MDC meets the maximum permissible limit of 0.03 wt% of chlorine in concrete set by American Concrete Institute Committee 318.

Non-destructive analysis of chlorine in fly ash cement concrete

Energy Technology Data Exchange (ETDEWEB)

Naqvi, A.A. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)], E-mail: aanaqvi@kfupm.edu.sa; Garwan, M.A.; Nagadi, M.M. [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Maslehuddin, M. [Center for Engineering Research, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Al-Amoudi, O.S.B. [Department of Civil Engineering, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Khateeb-ur-Rehman [Department of Physics, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia)

2009-08-11

Preventive measures against reinforcement corrosion in concrete require increasing concrete density to prevent the diffusion of chloride ions to the steel surface. Pozzolanic materials, such as fly ash (FA), silica fume (SF), and blast furnace slag (BFS) are added to concrete to increase its density. Monitoring the chloride concentration in concrete is required to assess the chances of reinforcement corrosion. In this study, FA was added to Portland cement concrete to increase its density. Prompt gamma neutron activation analysis (PGNAA) technique was utilized to analyze the concentration of chlorine in concrete. The chlorine concentration in the FA cement concrete was evaluated by determining the yield of 1.16, 1.95, 6.11, 6.62, 7.41, 7.79, and 8.58 MeV gamma-rays of chlorine from the FA concrete specimen containing 0.4-3.5 wt% chlorine. An excellent agreement was noted between the experimental yield of the prompt gamma-rays and the calculated yield obtained through the Monte Carlo simulations. The Minimum Detectable Concentration (MDC) of chlorine in FA cement concrete was also calculated. The best value of MDC limit of chlorine in the FA cement concrete was found to be 0.022{+-}0.007 and 0.038{+-}0.017 wt% for 1.16 and 6.11 MeV prompt gamma-rays, respectively. Within the statistical uncertainty, the lower bound of MDC meets the maximum permissible limit of 0.03 wt% of chlorine in concrete set by American Concrete Institute Committee 318.

The Effect of HCWA-PFA Hybrid Geopolymer Modification on the Properties of Soil

Directory of Open Access Journals (Sweden)

Hassian F.F.

2014-01-01

Full Text Available This study investigated the performance of the properties of foamed concrete when replacing volumes of cement of 10%, 15% and 20% by weight. A control unit of foamed concrete mixture made with Ordinary Portland Cement (OPC as well as samples containing 10%, 15% and 20% silica fume were prepared. Three mechanical property parameters of foamed concrete containing different percentages of silica fume were studied: compressive strength, flexural strength and splitting tensile strength. Silica fume is commonly used to increase the mechanical properties of concrete materials as well as for economic concerns. The foamed concrete in this study was cured at a relative humidity of 70% and a temperature of ±28°C. Improvements in the mechanical properties of foamed concrete were due to a significant densification in the microstructure of the cement paste matrix in the presence of silica fume hybrid supplementary binder as observed from micrographs obtained in the study. The overall results showed that silica fume has great potential to be utilized in foamed concrete as there was a noticeable enhancement in thermal and mechanical properties with the addition of silica fume.

Decreasing biotoxicity of fume particles produced in welding process.

Science.gov (United States)

Yu, Kuei-Min; Topham, Nathan; Wang, Jun; Kalivoda, Mark; Tseng, Yiider; Wu, Chang-Yu; Lee, Wen-Jhy; Cho, Kuk

2011-01-30

Welding fumes contain heavy metals, such as chromium, manganese, and nickel, which cause respiratory diseases and cancer. In this study, a SiO(2) precursor was evaluated as an additive to the shielding gas in an arc welding process to reduce the biotoxicity caused by welding fume particles. Transmission electron micrographic images show that SiO(2) coats on the surface of welding fume particles and promotes particle agglomeration. Energy dispersive X-ray spectroscopy further shows that the relative amount of silicon in these SiO(2)-coated agglomerates is higher than in baseline agglomerates. In addition, Escherichia coli (E. coli) exposed to different concentrations of pure SiO(2) particles generated from the arc welding process exhibits similar responses, suggesting that SiO(2) does not contribute to welding fume particle toxicity. The trend of E. coli growth in different concentrations of baseline welding fume particle shows the most significant inhibition occurs in higher exposure concentrations. The 50% lethal logarithmic concentrations for E. coli in arc welding particles of baseline, 2%, and 4.2% SiO(2) precursor additives were 823, 1605, and 1800 mg/L, respectively. Taken together, these results suggest that using SiO(2) precursors as an additive to arc welding shielding gas can effectively reduce the biotoxicity of welding fume. Copyright © 2010 Elsevier B.V. All rights reserved.

Nature and morphology of fumed oxides and features of interfacial phenomena

International Nuclear Information System (INIS)

Gun’ko, V.M.; Zarko, V.I.; Goncharuk, O.V.; Matkovsky, A.K.; Remez, O.S.; Skubiszewska-Zięba, J.; Wojcik, G.; Walusiak, B.; Blitz, J.P.

2016-01-01

Graphical abstract: - Highlights: • Effects of oxide surface structure on interfacial behavior of nonpolar and polar adsorbates. • Confined space effects on freezing and melting temperatures of bound adsorbates. • Equilibrium adsorption and evaporation rate vs. structure of nanooxide adsorbents. - Abstract: Individual and complex fumed nanooxides were studied using high-resolution transmission electron microscopy, X-ray diffraction, ultraviolet-visible (UV–vis) spectroscopy, differential scanning calorimetry, nuclear magnetic resonance spectroscopy, adsorption, desorption (evaporation), and quantum chemical methods. For mixed nanooxides in contrast to simple and small nanoparticles of individual silica or titania, complex core–shell nanoparticles (50–200 nm in size) with titania or alumina cores and silica or alumina shells can be destroyed under high-pressure cryogelation (HPCG), mechnochemical activation (MCA) that also affect the structure of aggregates of nanoparticles and agglomerates of aggregates becoming more compacted. This is accompanied by changes in color from white to beige of different tints and changes in the UV–vis spectra in the 300–600 nm range, as well as changes in crystalline structure of alumina. Any treatment of ‘soft’ nanooxides affects the interfacial behavior of polar and nonpolar adsorbates. For some of them, the hysteresis loops become strongly open. Rearrangement of secondary particles affects the freezing-melting point depression. Clusterization of adsorbates bound in pores causes diminution of heat effects during phase transition (freezing, fusion). Freezing point depression and increasing melting point cause significant hysteresis freezing-melting effects for adsorbates bound to oxide nanoparticles. The study shows that complex nanooxides can be more sensitive to external actions than simple nanooxides such as silica.

Nature and morphology of fumed oxides and features of interfacial phenomena

Energy Technology Data Exchange (ETDEWEB)

Gun’ko, V.M., E-mail: vlad_gunko@ukr.net [Chuiko Institute of Surface Chemistry, 17 General Naumov Street, 03164 Kyiv (Ukraine); Zarko, V.I.; Goncharuk, O.V.; Matkovsky, A.K.; Remez, O.S. [Chuiko Institute of Surface Chemistry, 17 General Naumov Street, 03164 Kyiv (Ukraine); Skubiszewska-Zięba, J.; Wojcik, G. [Faculty of Chemistry, Maria Curie-Skłodowska University, 20-031 Lublin (Poland); Walusiak, B.; Blitz, J.P. [Eastern Illinois University, Department of Chemistry, Charleston, IL 61920 (United States)

2016-03-15

Graphical abstract: - Highlights: • Effects of oxide surface structure on interfacial behavior of nonpolar and polar adsorbates. • Confined space effects on freezing and melting temperatures of bound adsorbates. • Equilibrium adsorption and evaporation rate vs. structure of nanooxide adsorbents. - Abstract: Individual and complex fumed nanooxides were studied using high-resolution transmission electron microscopy, X-ray diffraction, ultraviolet-visible (UV–vis) spectroscopy, differential scanning calorimetry, nuclear magnetic resonance spectroscopy, adsorption, desorption (evaporation), and quantum chemical methods. For mixed nanooxides in contrast to simple and small nanoparticles of individual silica or titania, complex core–shell nanoparticles (50–200 nm in size) with titania or alumina cores and silica or alumina shells can be destroyed under high-pressure cryogelation (HPCG), mechnochemical activation (MCA) that also affect the structure of aggregates of nanoparticles and agglomerates of aggregates becoming more compacted. This is accompanied by changes in color from white to beige of different tints and changes in the UV–vis spectra in the 300–600 nm range, as well as changes in crystalline structure of alumina. Any treatment of ‘soft’ nanooxides affects the interfacial behavior of polar and nonpolar adsorbates. For some of them, the hysteresis loops become strongly open. Rearrangement of secondary particles affects the freezing-melting point depression. Clusterization of adsorbates bound in pores causes diminution of heat effects during phase transition (freezing, fusion). Freezing point depression and increasing melting point cause significant hysteresis freezing-melting effects for adsorbates bound to oxide nanoparticles. The study shows that complex nanooxides can be more sensitive to external actions than simple nanooxides such as silica.

Welding fume exposure and chronic obstructive pulmonary disease in welders.

Science.gov (United States)

Koh, D-H; Kim, J-I; Kim, K-H; Yoo, S-W

2015-01-01

Occupational exposure is estimated to contribute 15% to the burden of chronic obstructive pulmonary disease (COPD). Welding fumes are suspected to accelerate the decline of lung function and development of COPD. To examine the relationship between welding fume exposure and COPD in Korean shipyard welders. The study involved a group of male welders working at two shipyards who underwent an annual health examination in 2010. Subjects completed a questionnaire about smoking habits and occupational history and a pulmonary function test (PFT) was carried out with strict quality control measures. Welding fume exposure concentrations were estimated using 884 measurements taken between 2002 and 2009 in one of the shipyards. Multiple linear and logistic regression was employed to evaluate the association between cumulative fume exposure and lung function parameters, controlling for age, height and cigarette smoking. Two hundred and forty subjects participated, with a mean age of 48 and mean work duration of 15 years. The mean cumulative fume exposure was 7.7mg/m(3). The prevalence of COPD was 15%. FEV1 and FVC showed non-significant negative correlations with cumulative fume exposure. Odds ratios of COPD were significantly elevated for the middle (3.9; 95% CI 1.4-13.3) and high exposure groups (3.8; 95% CI 1.03-16.2) compared with the low fume exposure group. Our findings support an association between welding fume exposure and increased risk of COPD. Further prospective study is needed to investigate whether this is a causal relationship. © The Author 2014. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

IR-spectroscopical investigations on the glass structure of porous and sintered compacts of colloidal silica gels

Science.gov (United States)

Clasen, Rolf; Hornfeck, M.; Theiss, Wolfgang

1991-08-01

The forming and sintering of fumed silica powders is an interesting route for the preparation of large, very pure or doped silica glasses with a precise geometry. The processing from the shaping of a porous compact to the sintering of transparent silica glass can be successfully investigated with optical spectroscopy. As only the dielectric function DF (a dielectric function is the square root of the complex refractive index) characterizes the material, the vibrational bands were calculated from reflectance measurements. In compacts of fine particles, the topology cannot be neglected. Therefore, the models describing topological effects are briefly reviewed. With these model calculations it could be proven that new bands in the compacts and the significant shifts in the reflectance spectra during sintering are mainly caused by topological effects and that changes in the glass structure play only a secondary role.

The Effect of Filler-Polymer Interactions on Cold-Crystallization Kinetics in Crosslinked, Silica Filled PDMS/PDPS Copolymer Melts

International Nuclear Information System (INIS)

Chien, A; DeTeresa, S; Thompson, L; Cohenour, R; Balazs, B; Maxwell, R S

2006-01-01

Crystallization in a series of variable crosslink density poly(dimethyl-diphenyl) siloxanes random block copolymers reinforced through a mixture of precipitated and fumed silica fillers has been studied by Differential Scanning Calorimetry (DSC), Dynamic Mechanical Analysis (DMA), and X-ray Diffraction (XRD). The silicone composite studied was composed of 94.6 mol% Dimethoylsiloxane, 5.1 mol% diphenylsiloxane, and 0.3 mol% methyl-vinyl siloxane (which formed crosslinking after a peroxide cure). The polymer was filled with a mixture of 21.6 wt. % fumed silica and 4.0 wt. % precipitated silica previously treated with 6.8 wt. % ethoxy-endblocked siloxane processing aid. The base composite was characterized by a molecular weight between crosslinks in the polymer network of ∼24 kDa and an overall molecular weight (including the influence of the silica fillers) between crosslinks of ∼11 kDa. Molecular weight between crosslinks and filler-polymer interaction strength were then modified by exposure to γ-irradiation in either air or vacuum. The unirradiated material exhibited crystallization at -80 C as measured by DSC with a 16% crystallization as measured by XRD. Isothermal DMA experiments illustrated that crystallization at -85 C occurred over a 1.8 hour period in silica-filled systems and 2.2-2.6 hours in unfilled systems. The onset of crystallization typically occurred after a 30-minute incubation/nucleation period. The crystallization kinetics were dependent on crosslink density. Changes in molecular weight of a factor of two did not, however, change the amount of crystallization. Irradiation in vacuum resulted in faster overall crystallization rates compared to air irradiation for the same crosslink density, likely due to a reduction in the interaction between the polymer chains and the silica filler surface. Modulated differential scanning calorimetry contrasted the crystallization and melting behavior of pure PDMS versus the PDMS/PDPS base copolymer and helped

Pulmonary fibrosis and exposure to steel welding fume.

Science.gov (United States)

Cosgrove, M P

2015-12-01

Arc welders who have been exposed to high concentrations of steel welding fume for prolonged periods of time may develop pulmonary fibrosis but the nature of the fibrotic changes has been debated over the last 80 years without any clear international consensus. To characterize the nature of the pulmonary fibrosis that develops in response to steel welding fume exposure and to provide a working hypothesis that would explain the findings of the existing research, to provide a platform for future research and to inform future occupational and clinical management of welders with pulmonary effects from welding fume. Review of the world literature on pulmonary fibrosis and welding of steel in all languages using PubMed, with further secondary search of references in the articles found in the primary search. Google and Reference Manager were used as further confirmatory search tools. Only case series and case reports were found but these provided consistent evidence that the consequence of exposure to steel welding fume at high levels for a prolonged period of time is a type of pulmonary fibrosis similar to, and possibly the same as, respiratory bronchiolitis which eventually develops into desquamative interstitial pneumonia with ongoing exposure. Steel welding fume may cause an occupational respiratory bronchiolitis which may develop into de squamative interstitial pneumonia with ongoing exposure. This concept may explain the difficulties in interpreting the wider literature on welding fume and lung function at lower exposures and may also explain the increased risk of lung cancer in welders. © The Author 2015. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Genotoxic Effects of Exposure to Gasoline Fumes on Petrol Pump Workers.

Science.gov (United States)

Shaikh, Amrin; Barot, Darshana; Chandel, Divya

2018-04-01

Petrol pump workers are occupationally exposed to gasoline and its fumes consisting of several mutagenic chemicals. To evaluate the genotoxic effects of exposure to gasoline fumes on petrol pump workers. The study groups included 70 petrol pump workers (exposed group) and 70 healthy age-matched individuals with no known exposure (comparison group). Buccal micronucleus cytome assay (BMCyt) was performed to check the genotoxicity caused due to inhalation of gasoline fumes. The frequencies of micronucleated cells, nuclear bud, condensed chromatin cells, karyorrhectic cells, pyknotic cells, and karyolytic cells were significantly higher in the exposed workers compared to the comparison group. Exposure to gasoline fumes is associated with increased frequency of cell abnormalities. This may lead to various health consequences including cancer in those occupationally exposed to gasoline fumes.

Effect of Different Supplementary Cementitious Materials on Mechanical and Durability Properties of Concrete

Directory of Open Access Journals (Sweden)

Rahul Sharma

2016-09-01

Full Text Available Concrete is the most widely used composite in the world. Ordinary Portland cement (OPC is the most commonly used binding material but the energy required for its production is large and its production leads to release of green house gases in the atmosphere therefore, the need for supplementary cementitious material is real. The utilization of Fly Ash (FA, Silica Fume (SF,Metakaolin (MK and Ground Granulated Blast Furnace Slag (GGBS, as a pozzolanic material for concrete has received considerable attention in the recent years. This interest is a part of the widely spread attention directed towards the utilization of wastes and industrial byproducts in order to minimize the Portland cement consumption, the manufacture of which is being environment damaging. The paper reviews were carried out on the use of FA, SF, MK and GGBS as partial pozzolanic replacement for cement in concrete. The literature demonstrates that GGBS was found to increase the mechanical and durability properties at later age depending upon replacement level. Silica fume concrete performed better than OPC concrete even at early period for production of high strength concrete and high performance concrete. Fly ash increases the later age strength due to slow rate of pozzlanic reaction. Metakaolin was found to improve early age strength as well as long term strength but had poor workability.

Improved technology for spun-cast concrete poles

Energy Technology Data Exchange (ETDEWEB)

Dilger, W H; Ghali, A

1984-07-01

Different types of concrete were investigated with the goal of developing concrete suitable for the production of spun-cast concrete poles. A total of 65 different concrete mixes were investigated, with the suitability criteria defined as: compactability, no segregation of the mix components during the spinning operation, no shrinkage cracking, high strength, and durability. High strength normal weight concretes and semi-lightweight concretes, both with and without fly ash and/or silica fume and with different types of admixtures were used to produce spun-cast concrete pole segments. Of the 35 lightweight concretes only 3 were considered successful, as in all other specimens the inner layer of coarse aggregate was not well embedded in the mortar, and many mixes could not be compacted properly because they were too stiff, too wet, or started to set before spinning commenced. The three successful specimens contained fly ash and one contained silica fume, and had low water/cement ratios (0.26 to 0.29). Of the 23 normal weight concretes tested, only 5 were considered suitable, and all these had a sand/coarse aggregate ratio of 0.25 or smaller and a cement content between 350 and 400 kg/m{sup 3}. A theoretical study of the stresses in the end zones of pretensioned poles is presented. 10 refs., 53 figs., 14 tabs.

Effect of Limestone Powder on Acid Attack Characteristics of Cement Pastes

Directory of Open Access Journals (Sweden)

Shuhua LIU

2014-12-01

Full Text Available The acid resistance of cement pastes containing limestone powder with two different water-binder (w/b ratios exposed to acetic (pH = 4 and sulfuric acid (pH = 2 solutions respectively were investigated in this paper. Limestone powder, fly ash and silica fume were also added to the cement paste mixture at different proportions. Static and flowing aqueous environments were set in this experiment. Strength and microstructure of the pastes after acid attack were investigated by using strength test, X-ray diffractometer (XRD and scanning electron microscopy (SEM. The experimental results show that the erosion degree depends not only on pH value of the solution and w/b ratio of the pastes, but also on the content of limestone powder. Acetic acid reacts with calcium hydroxide and carbonate thus dissolving the pastes, while sulfuric acid consumed calcium hydroxide, and generated gypsum and ettringite. The consumption of calcium hydroxide in the flowing solution group is higher than that in the static solution because the flowing sulfuric acid solution has negative effect upon the gypsum crystallization. Fly ash and silica fume are beneficial to limestone cement paste because of the less calcium hydroxide formation, which is among the hydrates vulnerable to acid erosion. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6231

Soluble transition metals cause the pro-inflammatory effects of welding fumes in vitro

International Nuclear Information System (INIS)

McNeilly, Jane D.; Heal, Mathew R.; Beverland, Iain J.; Howe, Alan; Gibson, Mark D.; Hibbs, Leon R.; MacNee, William; Donaldson, Ken

2004-01-01

Epidemiological studies have consistently reported a higher incidence of respiratory illnesses such as bronchitis, metal fume fever (MFF), and chronic pneumonitis among welders exposed to high concentrations of metal-enriched welding fumes. Here, we studied the molecular toxicology of three different metal-rich welding fumes: NIMROD 182, NIMROD c276, and COBSTEL 6. Fume toxicity in vitro was determined by exposing human type II alveolar epithelial cell line (A549) to whole welding fume, a soluble extract of fume or the 'washed' particulate. All whole fumes were significantly toxic to A549 cells at doses >63 μg ml -1 (TD 50; 42, 25, and 12 μg ml -1 , respectively). NIMROD c276 and COBSTEL 6 fumes increased levels of IL-8 mRNA and protein at 6 h and protein at 24 h, as did the soluble fraction alone, whereas metal chelation of the soluble fraction using chelex beads attenuated the effect. The soluble fraction of all three fumes caused a rapid depletion in intracellular glutathione following 2-h exposure with a rebound increase by 24 h. In addition, both nickel based fumes, NIMROD 182 and NIMROD c276, induced significant reactive oxygen species (ROS) production in A549 cells after 2 h as determined by DCFH fluorescence. ICP analysis confirmed that transition metal concentrations were similar in the whole and soluble fractions of each fume (dominated by Cr), but significantly less in both the washed particles and chelated fractions. These results support the hypothesis that the enhanced pro-inflammatory responses of welding fume particulates are mediated by soluble transition metal components via an oxidative stress mechanism

Hepatotoxic and Nephrotoxic Effects of Petroleum Fumes on Petrol ...

African Journals Online (AJOL)

DR SULEIMAN

Hepatotoxic and Nephrotoxic Effects of Petroleum Fumes on Petrol Attendants in Ibadan, Nigeria. *1A.L. Ogunneye ... inhalation of petrol fumes is associated with adverse effect on the kidney and liver function. ..... neurotoxicity in mice. African ...

Genotoxic Effects of Exposure to Gasoline Fumes on Petrol Pump Workers

Directory of Open Access Journals (Sweden)

Amrin Shaikh

2018-04-01

Full Text Available Background: Petrol pump workers are occupationally exposed to gasoline and its fumes consisting of several mutagenic chemicals. Objective: To evaluate the genotoxic effects of exposure to gasoline fumes on petrol pump workers. Methods: The study groups included 70 petrol pump workers (exposed group and 70 healthy age-matched individuals with no known exposure (comparison group. Buccal micronucleus cytome assay (BMCyt was performed to check the genotoxicity caused due to inhalation of gasoline fumes. Results: The frequencies of micronucleated cells, nuclear bud, condensed chromatin cells, karyorrhectic cells, pyknotic cells, and karyolytic cells were significantly higher in the exposed workers compared to the comparison group. Conclusion: Exposure to gasoline fumes is associated with increased frequency of cell abnormalities. This may lead to various health consequences including cancer in those occupationally exposed to gasoline fumes.

Calculation of crack stress density of cement base materials

Directory of Open Access Journals (Sweden)

Chun-e Sui

2018-01-01

Full Text Available In this paper, the fracture load of cement paste with different water cement ratio, different mineral admixtures, including fly ash, silica fume and slag, is obtained through experiments. the three-dimensional fracture surface is reconstructed and the three-dimensional effective area of the fracture surface is calculated. the effective fracture stress density of different cement paste is obtained. The results show that the polynomial function can accurately describe the relationship between the three-dimensional total area and the tensile strength

Mixed materials for concrete. Concrete yo konwazai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kono, K [Tokushima Univ., Tokushima (Japan). Faculty of Engineering

1994-07-05

The materials except cement, water and aggregate added into the cement paste, mortar or concrete before the execution of smashing are called mixed materials. The mixed materials are indispensable to the concrete for improving the quality of the fresh concrete as well as the hardened concrete; providing the characteristics suitable for the operation; and increasing the economy. In this paper, the main mixed materials including fly ash, which is the by-product in coal thermoelectric power station; silica fume; micropowder of slag in blast furnace; expansive materials and so on are described summarily. Especially, silica fume is the by-product, which are the super micro-powders with the average size around 0.1 micrometer, collected by the dust-collector from the waste gas generated during the manufacture in the electric furnace of ferrosilicon, which is an alloy iron, or silicon metal used as the deacidificating and desulfurizing agents in the steel production. But the most part thereof is depended on the import since the domestic output is low. 38 refs., 19 figs., 6 tabs.

Study on low permeable backfill materials. Backfill materials for waste disposal facilities; Koshisuisei juten zairyo ni kansuru kenkyu. Hoshasei haikibutsu shobun shisetsu eno tekiyosei kenkyu

Energy Technology Data Exchange (ETDEWEB)

Shiraishi, F; Konishi, M; Shiraishi, H [Okumura Corp., Osaka (Japan)

1994-11-15

A discussion was given on the fundamental properties of mortar made from cement mixed with silica fume. Four kinds of silica fumes with different particle size distributions were used. The following results were obtained: distribution of pores in mortar admixed with silica fume shifts to the smaller radius side; while the admixture increases the compression strength in mortar, the increasing trend varies depending on the kinds of silica fumes; this is thought to be caused from the difference in pozzolan activity between silica fumes; and the strength increase is caused by densification of the structure due to the pozzolan reaction that is generated after hydration, or in other words, decrease in the pore volume. The applicability of the mortar was investigated as a filling mortar to fill up clearances between wastes. It was found that the filling performance can be controlled by mixing silica fume at an adequate level and adjusting the viscosity. The diffusion coefficient for the admixed concrete is smaller by 30% to one digit than that for the ordinary concrete. High-performance water stopping concrete of 0.11 {times} 10{sup 4}cm {sup 2}/s at maximum was obtained. The concrete can be regarded as a material having superb filling and water stopping performances. 6 refs., 4 figs., 5 tabs.

A NOVEL GEL ELECTROLYTE FOR VALVE-REGULATED LEAD ACID BATTERY

Directory of Open Access Journals (Sweden)

Metin GENÇTEN

2017-03-01

Full Text Available A novel gel electrolyte system used in lead-acid batteries was investigated in this work. The gel systems were prepared by addition different amount of Al2O3, TiO2 and B2O3 into the gelled system consisting of 6 wt% fumed silica and 30 wt% sulfuric acid solution. The anodic peak currents and peak redox capacities of the gel electrolytes were characterized by cyclic voltammetric method. They decreased by the time B2O3 and Al2O3 were used as additives in fumed silica based gel electrolyte system. However, these values increased by the adding 3.0 wt% of TiO2. The solution and charge transfer resistances of the gel electrolytes were investigated by electrochemical impedance spectroscopy. While the solution resistances were lower in gel systems having different amount additives than pure fumed silica based gel, the charge transfer resistance was the lowest in gel electrolytes consisting fumed silica and fumed silica-TiO2. The battery performances were studied by obtaining discharge curves of prepared gel electrolytes. The performance of gelled systems were higher than that of non-gelled electrolyte at room temperature. The mixture of fumed silica-TiO2 was suggested an alternative gel formulation for gel VRLA batteries.

When are fume-cupboards necessary in hospital radioisotope laboratories

Energy Technology Data Exchange (ETDEWEB)

Birks, J L [Singleton Hospital, Swansea (UK)

1976-06-01

Suggestions are made for procedures likely to require the provision of efficient fume-cupboards in hospital radioisotope laboratories. All such departments undertaking in vivo radioisotope procedures will require a supply of sterile materials, but only some of these will also require a fume-cupboard, since the use of a relatively inexpensive aseptic cabinet, without air flow and exhaust system, may suffice for such procedures as the labelling of blood cells or plasma. Efficient fume-cupboards may be required in hospital laboratories that are routinely concerned with the elution of generators of isotopes such as /sup 99/Tcsup(m) and /sup 113/Insup(m), the sterilization of radiopharmaceuticals (e.g. technetium-sulphur colloid) requiring the use of a pressure cooker, and the storage and handling of therapeutic quantities of /sup 131/I. Copious general ventilation of isotope rooms may be preferable to the too frequent incorporation of unnecessary fume-cupboards.

Performance at high temperature of alkali-activated slag pastes produced with silica fume and rice husk ash based activators

Directory of Open Access Journals (Sweden)

Bernal, S. A.

2015-06-01

Full Text Available This study assessed the mechanical properties, and structural changes induced by high temperature exposure, of alkali-silicate activated slag cements produced with sodium silicates derived from silica fume (SF and rice husk ash (RHA. Similar reaction products were identified, independent of the type of silicate used, but with subtle differences in the composition of the C-S-H gels, leading to different strength losses after elevated temperature exposure. Cements produced with the alternative activators developed higher compressive strengths than those produced with commercial silicate. All samples retained strengths of more than 50 MPa after exposure to 600 °C, however, after exposure to 800 °C only the specimens produced with the RHA-based activator retained measurable strength. This study elucidated that silicate-activated slag binders, either activated with commercial silicate solutions or with sodium silicates based on SF or RHA, are stable up to 600 °C.Este estudio evaluó las propiedades mecánicas, y cambios estructurales inducidos por exposición a temperaturas elevadas, de cementos de escoria activada alcalinamente producidos con silicatos sódicos derivados de humo de sílice (SF y ceniza de cascarilla de arroz (RHA. Se identificaron productos de reacción similares, independiente del tipo de silicato utilizado, pero con diferencias menores en la composición de las geles C-S-H, lo cual indujo diferentes pérdidas de resistencia posterior a exposición a temperaturas elevadas. Los cementantes producidos con los activadores alternativos desarrollaron resistencias a la compresión más altas que aquellos producidos con silicato comercial. Todas las muestras retuvieron resistencias de más de 50 MPa posterior a la exposición a 600 °C, sin embargo, posterior a la exposición a 800 °C únicamente muestras producidas con activadores de RHA retuvieron resistencias medibles. Este estudio elucidó que cementantes de escoria activada con

Increased lung function decline in blue-collar workers exposed to welding fumes.

Science.gov (United States)

Thaon, Isabelle; Demange, Valérie; Herin, Fabrice; Touranchet, Annie; Paris, Christophe

2012-07-01

There is no consensus at the present time about the effect of welding on lung function decline. This study compared lung function decline between blue-collar workers exposed and not exposed to welding fumes in a French longitudinal cohort of 21,238 subjects aged 37 to 52 years at inclusion. Medical data, occupation, sector of activity, and spirometry were recorded twice by occupational physicians in 1990 and 1995. A job-exposure matrix was used to identify 503 male blue-collar workers exposed to welding fumes and 709 control subjects and to define the weekly duration of exposure to welding fumes. Baseline lung function parameters were higher in workers exposed to welding fumes than in control subjects. After a 5-year follow-up, welding-fume exposure was associated with a nonsignificant decline in FVC (P = .06) and FEV(1) (P = .07) after adjustment for age, pack-years, BMI, and baseline value of the parameter. A significant accelerated decline in FEV(1) (P = .046) was also observed in never smokers exposed to welding fumes. An “exposure-response” relationship was observed between FEV(1) decline and weekly duration of exposure to welding fumes in nonsmokers but not in smokers. Blue-collar workers exposed to welding fumes showed accelerated decline in lung function, which, in nonsmokers, was related to weekly duration of exposure.

Hierarchical zeolites from class F coal fly ash

Science.gov (United States)

Chitta, Pallavi

Fly ash, a coal combustion byproduct is classified as types class C and class F. Class C fly ash is traditionally recycled for concrete applications and Class F fly ash often disposed in landfills. Class F poses an environmental hazard due to disposal and leaching of heavy metals into ground water and is important to be recycled in order to mitigate the environmental challenges. A major recycling option is to reuse the fly ash as a low-cost raw material for the production of crystalline zeolites, which serve as catalysts, detergents and adsorbents in the chemical industry. Most of the prior literature of fly ash conversion to zeolites does not focus on creating high zeolite surface area zeolites specifically with hierarchical pore structure, which are very important properties in developing a heterogeneous catalyst for catalysis applications. This research work aids in the development of an economical process for the synthesis of high surface area hierarchical zeolites from class F coal fly ash. In this work, synthesis of zeolites from fly ash using classic hydrothermal treatment approach and fusion pretreatment approach were examined. The fusion pretreatment method led to higher extent of dissolution of silica from quartz and mullite phases, which in turn led to higher surface area and pore size of the zeolite. A qualitative kinetic model developed here attributes the difference in silica content to Si/Al ratio of the beginning fraction of fly ash. At near ambient crystallization temperatures and longer crystallization times, the zeolite formed is a hierarchical faujasite with high surface area of at least 360 m2/g. This work enables the large scale recycling of class F coal fly ash to produce zeolites and mitigate environmental concerns. Design of experiments was used to predict surface area and pore sizes of zeolites - thus obviating the need for intense experimentation. The hierarchical zeolite catalyst supports tested for CO2 conversion, yielded hydrocarbons

Short term exposure to cooking fumes and pulmonary function

Directory of Open Access Journals (Sweden)

Qvenild Torgunn

2009-05-01

Full Text Available Abstract Background Exposure to cooking fumes may have different deleterious effects on the respiratory system. The aim of this study was to look at possible effects from inhalation of cooking fumes on pulmonary function. Methods Two groups of 12 healthy volunteers (A and B stayed in a model kitchen for two and four hours respectively, and were monitored with spirometry four times during twenty four hours, on one occasion without any exposure, and on another with exposure to controlled levels of cooking fumes. Results The change in spirometric values during the day with exposure to cooking fumes, were not statistically significantly different from the changes during the day without exposure, with the exception of forced expiratory time (FET. The change in FET from entering the kitchen until six hours later, was significantly prolonged between the exposed and the unexposed day with a 15.7% increase on the exposed day, compared to a 3.2% decrease during the unexposed day (p-value = 0.03. The same tendency could be seen for FET measurements done immediately after the exposure and on the next morning, but this was not statistically significant. Conclusion In our experimental setting, there seems to be minor short term spirometric effects, mainly affecting FET, from short term exposure to cooking fumes.

ThE EFFECT OF METAKOLIN, MICROSILICA AND NANOSILICA ON THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF CEMENT MORTAR

Directory of Open Access Journals (Sweden)

H. R. Sobhani Kavkani

2016-06-01

Full Text Available Different mineral admixtures of Indian metakaolin, Iranian silica fume and nanosilica were used to produce high performance mortars. Two different sands types with grain size of 0.015-4mm were mixed with type II Portland cement, polycarboxylate superplasticizer,mineral admixture with 650kg/m3 cement content and water/cement ratio of 0.35. Different amount of cement was replaced by metakaolin or silica fume (5-15wt% or nanosilica (0.8-5wt%. After mixing, moulding and curing, compressive strength, electrical resistivity and abrasion resistance were studied. The maximum compressive strength of 28 days samples were 76MPa, 79MPa and 75MPa for 15wt% substitution of cement with metakaolin, silica fume and 5wt% with nanosilica. The compressive strength of these samples showed 28%, 33% and 26% increment in comparison with reference sample, respectively. X-ray patterns showed that replacing silica fume leads to reduction of Portlandite (Ca(OH2 phase. This can be attributed to the pozzolanic reaction and formation of new hydrated calcium silicate phase (CSH that caused improvement of strength of admixtures containing samples. The microstructure of silica fume containing sample also showed better bond between sand and matrix. The electrical resistivity of samples with 15wt% metakaolin or silica fume and 5wt% nanosilica reach to 21kΩ.cm, 15 kΩ.cm and 10kΩ.cm, respectively. These samples showed high durability and corrosion resistance relative to reference samples (3.4 kΩ.cm. The abrasion resistance of different admixtures, specially silica fume containing samples were improved.

Properties of nano-silica modified pervious concrete

Directory of Open Access Journals (Sweden)

Bashar S. Mohammed

2018-06-01

Full Text Available The aim of this study is to evaluate the effects of inclusion nano-silica (also known as nano-SiO2 on the properties of pervious concrete containing fly ash (FA as a partial replacement to cement. It has been found, for cementitious paste, that incorporating NS leads to reduce the cumulative pore volume by 13.4%. While the compressive strength of NS modified pervious concrete has been improved without adversely affecting its void ratio and permeability. The workability has been adversely affected by the inclusion of NS, which can be enhanced by incorporating the fly ash and superplasticizer. The porosity of cementitious paste has increased as the FA content is increased. These results are in good agreement with SEM results. For the pervious concrete voids ratio, permeability and infiltration rate were decreased against the increase of paste to the aggregate ratio Response surface methodology (RSM has also been used to develop a model for navigating the design space of NS modified pervious concrete. Models revealed 95% significance of confidence level with difference less than 0.2 between Pred R-Squared value of 0.9515 and Adj R-Squared. The general expression has been developed for all the responses with the different coefficients using the RSM. Keywords: Fly ash, Final setting time, Infiltration rate, Pervious concrete, Nano-silica

INS study of intermolecular interaction at the silicone-fumed silica interface

International Nuclear Information System (INIS)

Sheka, E.F.; Natkaniec, I.

1999-01-01

Complete text of publication follows. The paper presents results related to the interface formed between finned silica particles and polydimethylsiloxane polymers, presented in the study by a five-member cyclic oligomer SiS. The substrate surface is terminated by either hydroxyl units or by trimethylsiloxy ones. When the interface is formed, methyl units are the main constituents providing neutron scattering. Protium/deuterium exchange has been used to distinguish the latter belonging to either adsorbate or substrate. A detailed analysis of the intermolecular interaction impact on both adsorbed molecule and substrate has been performed. The observed features are supported by the vibrational spectra calculations performed on the basis of a modem quantum-chemical approach and supplemented by the solution of the inverse spectral problem. (author)

Zeolite from fly ash: synthesis and characterization

Indian Academy of Sciences (India)

Unknown

to attempt making zeolite from fly ash (Höller and Wir- sching 1985; Henmi ... thermal treatment method to synthesize low silica NaX- type zeolite from .... catalytic applications. Mixture of ... amount of Fe2O3 and the oxides of Mg, Ca, P, Ti etc. The chemical ..... This work is partly supported by the Ministry of Human. Resource ...

Evaluation of characterisation techniques for particulate weld fume morphology

International Nuclear Information System (INIS)

Sterjovski, Z.; Monaghan, B.J.; Norrish, J.

2009-01-01

An evaluation of three techniques: scanning electron microscopy (SEM); transmission electron microscopy (TEM); and laser diffraction (LD), was carried out to determine the most suitable technique for the particle-size measurement of particulate-welding fume collected during the robotic gas-metal-arc welding (GMAW) of plain-carbon steel. Particulate fume was deposited onto an Al stub positioned at a horizontal distance of 30 mm and a vertical height of 50 mm from the welding arc, and was then prepared for SEM, TEM and LD sizing. Results are presented for paniculate-welding fume collected for three welding voltages (20, 23 and 26 V) and two metal-transfer modes (dip and dip/globular). TEM imaging was found to be the most effective of the three sizing technique as it was able to resolve both fine nano-particles (5 ran diameter) and coarse nano-particles (>100 mn diameter). The TEM approach showed that results determined were reproducible and that the majority of fume particles produced at the welding voltages investigated were less than 40 nm in diameter. SEM (La B6 filament) images were shown to be inadequate for the quantitative-size analysis of paniculate-welding fume due to the limited resolution of the microscope (-40 nm). However. SEM images did confirm that at a welding voltage of 23 V the majority of particle sizes produced were less than 100 nm in diameter, and thus supported the conclusion that the individual fume particles are predominantly in the nanometre size range. LD gave unexpectedly large mean particle sizes and did not detect particles less than 180 run in diameter. It is concluded that the LD technique measures particle agglomerates and/or simultaneously monitors multiple particles in the beam path.

EFFECTS OF FIRE FUMES ON ALMOND SAFETY AND QUALITY

Directory of Open Access Journals (Sweden)

Amanda Ramírez-Gandolfo

2011-08-01

Full Text Available A fire originated and burnt two cold chambers; the present study focused on almonds stored in adjacent chambers (4, 5, 6 and 13 and evaluated both their food safety and quality. Testing for polycyclic aromatic hydrocarbons, polychlorinated dibenzo-p-dioxins and dibenzofurans was carried out in affected facilities, packaging and almonds. Experimental results proved that fire fumes did not reach chambers 4-6, but traces were found in bin packaging of chamber 13; thus, packaging from this chamber were changed. Concentrations of benzo(apyrene were low enough to prove that fire fumes did not get in contact with the stored almonds. Later, only volatile compounds typical of nuts were identified in both raw and toasted almonds. Finally, a trained panel concluded that no sensory signal of fumes reaching almonds was found. This manuscript could be taken as a model protocol to establish whether fire fumes have reached and affected the safety and/or quality of foods. This information will be especially useful for insurance companies.

42 CFR 84.1147 - Silica mist test for dust, fume, and mist respirators; minimum requirements.

Science.gov (United States)

2010-10-01

... shall be ground to pass 99+ percent through a 270-mesh sieve. (e) Samples of the test suspension will be taken during each test period for analysis. (f) The total amount of silica mist unretained in the...

Evaluation of capillary pore size characteristics in high-strength concrete at early ages

International Nuclear Information System (INIS)

Igarashi, Shin-ichi; Watanabe, Akio; Kawamura, Mitsunori

2005-01-01

The quantitative scanning electron microscope-backscattered electron (SEM-BSE) image analysis was used to evaluate capillary porosity and pore size distributions in high-strength concretes at early ages. The Powers model for the hydration of cement was applied to the interpretation of the results of image analysis. The image analysis revealed that pore size distributions in concretes with an extremely low water/binder ratio of 0.25 at early ages were discontinuous in the range of finer capillary pores. However, silica-fume-containing concretes with a water/binder ratio of 0.25 had larger amounts of fine pores than did concretes without silica fume. The presence of larger amounts of fine capillary pores in the concretes with silica fume may be responsible for greater autogenous shrinkage in the silica-fume-containing concretes at early ages

[Emission Characteristics of Water-Soluble Ions in Fumes of Coal Fired Boilers in Beijing].

Science.gov (United States)

Hu, Yue-qi; Ma, Zhao-hui; Feng, Ya-jun; Wang, Chen; Chen, Yuan-yuan; He, Ming

2015-06-01

Selecting coal fired boilers with typical flue gas desulfurization and dust extraction systems in Beijing as the study objects, the issues and characteristics of the water-soluble ions in fumes of coal fired boilers and theirs influence factors were analyzed and evaluated. The maximum mass concentration of total water-soluble ions in fumes of coal fired boilers in Beijing was 51.240 mg x m(-3) in the benchmark fume oxygen content, the minimum was 7.186 mg x m(-3), and the issues of the water-soluble ions were uncorrelated with the fume moisture content. SO4(2-) was the primary characteristic water-soluble ion for desulfurization reaction, and the rate of contribution of SO4(2-) in total water-soluble ions ranged from 63.8% to 81.0%. F- was another characteristic water-soluble ion in fumes of thermal power plant, and the rate of contribution of F- in total water-soluble ions ranged from 22.2% to 32.5%. The fume purification technologies significantly influenced the issues and the emission characteristics of water-soluble ions in fumes of coal fired boilers. Na+ was a characteristic water-soluble ion for the desulfurizer NaOH, NH4+ and NO3+ were characteristic for the desulfurizer NH4HCO3, and Mg2+ was characteristic for the desulfurizer MgO, but the Ca2+ emission was not increased by addition of the desulfurizer CaO or CaCO3 The concentrations of NH4+ and NO3- in fumes of thermal power plant were lower than those in fumes of industrial or heating coal fired boilers. The form of water-soluble ions was significantly correlated with fume temperature. The most water-soluble ions were in superfine state at higher fume temperature and were not easily captured by the filter membrane.

Impact of pozzolanic binder addition on stabilization of polluted dredged sediments on its potential reuse as a new material resource for road construction in Basse Normandie, France

Science.gov (United States)

Silitonga, E.

2018-02-01

Due to the increase of the amount of marine dredged sediments (MDS) and the cost of managing the disposal site is very high, a reutilization of dredged sediment is urgently needed in France. The primary goal of this research is to find a domain for reuse of MDS materials as a new material regarding the environmental issues, and other requirement needed. In this study, the MDS was used as replacement material in road construction. Hence, various tests need to be realized to identify if MDS could achieve the requirement needed in this domain. The secondary objective is to enhance the geotechnical characteristic and to reduce the pollution content of the MDS, by incorporating binders and sediments, and revealed the geotechnical characteristic. The geotechnical test result shows that the stabilization by hydraulics binders improve the geotechnical characteristic and could fulfil the requirement needed. The present of Fly Ash and Silica Fume in this study is aimed to reduce the pollution level, especially the heavy metal content. After the geotechnical study in laboratory results shows as expected then the study to identify the chemical characteristic was realized. In order to evaluate the environmental impacts, leaching test was performed. The Leaching test result shows that with 7% of Silica Fume and 10% of Fly Ash capable to fulfil the criteria needed, hence, the use of MDS is consider safe in term of geotechnical and environmental impact, as a new material in road construction

Laser Printing of Superhydrophobic Patterns from Mixtures of Hydrophobic Silica Nanoparticles and Toner Powder.

Science.gov (United States)

Ngo, Chi-Vinh; Chun, Doo-Man

2016-11-08

In this work, a new and facile dry printing method was developed for the direct fabrication of superhydrophobic patterns based on silica nanoparticles. Mixtures of hydrophobic fumed silica nanoparticles and toner powder were printed on paper and polymer sheets using a commercial laser printer to produce the superhydrophobic patterns. The mixing ratio of the toner powder (for the laser printer) to hydrophobic silica was also investigated to optimize both the printing quality and the superhydrophobicity of the printed areas. The proper mixing ratio was then used to print various superhydrophobic patterns, including triangular, square, circular, and complex arrangements, to demonstrate that superhydrophobic surfaces with different patterns can be fabricated in a few seconds without any post-processing. The superhydrophobicity of each sample was evaluated by contact angle measurements, and all printed areas showed contact angles greater than 150°. The research described here opens the possibility of rapid production of superhydrophobic surfaces with various patterns. Ultimately, the obtained findings may have a significant impact on applications related to self-cleaning, control of water geometry and position, fluid mixing and fluid transport.

Laser Printing of Superhydrophobic Patterns from Mixtures of Hydrophobic Silica Nanoparticles and Toner Powder

Science.gov (United States)

Ngo, Chi-Vinh; Chun, Doo-Man

2016-11-01

In this work, a new and facile dry printing method was developed for the direct fabrication of superhydrophobic patterns based on silica nanoparticles. Mixtures of hydrophobic fumed silica nanoparticles and toner powder were printed on paper and polymer sheets using a commercial laser printer to produce the superhydrophobic patterns. The mixing ratio of the toner powder (for the laser printer) to hydrophobic silica was also investigated to optimize both the printing quality and the superhydrophobicity of the printed areas. The proper mixing ratio was then used to print various superhydrophobic patterns, including triangular, square, circular, and complex arrangements, to demonstrate that superhydrophobic surfaces with different patterns can be fabricated in a few seconds without any post-processing. The superhydrophobicity of each sample was evaluated by contact angle measurements, and all printed areas showed contact angles greater than 150°. The research described here opens the possibility of rapid production of superhydrophobic surfaces with various patterns. Ultimately, the obtained findings may have a significant impact on applications related to self-cleaning, control of water geometry and position, fluid mixing and fluid transport.

Environmental exposure to cooking oil fumes and cervical intraepithelial neoplasm

International Nuclear Information System (INIS)

Wu, M.-T.; Lee, L.-H.; Ho, C.-K.; Wu, S.-C.; Lin, L.-Y.; Cheng, B.-H.; Liu, C.-L.; Yang, C.-Y.; Tsai, H.-T.; Wu, T.-N.

2004-01-01

The fumes from cooking oil, similar to cigarette smoke, contain numerous carcinogens such as polycyclic aromatic hydrocarbons, aromatic amines, nitro-polycyclic aromatic hydrocarbons, etc. In this study, we examined the association between exposure to cooking oil fumes and the risk of cervical intraepithelial neoplasm. The study population in this nested case-control study consisted of women above the age of 19 years living in Chia-Yi County, located in the southwestern Taiwan, who had received pap smear screening between October, 1999, and December, 2000 (n=32,466). The potential cases were women having lesions greater than cervical intraepithelium neoplasm II (≥CIN2) reconfirmed by cervical biopsy (n=116). The potential controls (case: control=1:2) were age-matched (±2 years) and residence-matched women who had normal pap smears within 6 months of the cases. In total, 100 cases and 197 controls were completely interviewed by public health nurses about cooking methods, ventilation, and other potential risk factors. Women who cooked at home in a kitchen (n=269) without the presence of a fume extractor at least once a week between the ages of 20 and 40 had a 2.29 times higher risk [95% confidence interval (CI)=1.08-4.87] of developing cervical intraepithelial neoplasm than those who did not cook once a week in such a kitchen during the same age span, after adjusting for other potential confounders. This finding was further strengthened by the finding that women who did not use the fume extractors had a 2.47 times higher risk (95% CI=1.15-5.32) of developing cervical intraepithelial neoplasm than women who cooked in kitchens with fume extractors that were always switched on while cooking. We also found a joint protective effect of fume extractor use among women older than 40 years (n=202) if they used the extractors during both age spans of their lives, ages 20-40 and >40 years. Comparing our findings on women more than 40 years old who used fume extractors during

Workplace field testing of the pressure drop of particulate respirators using welding fumes.

Science.gov (United States)

Cho, Hyun-Woo; Yoon, Chung-Sik

2012-10-01

In a previous study, we concluded that respirator testing with a sodium chloride aerosol gave a conservative estimate of filter penetration for welding fume aerosols. A rapid increase in the pressure drop (PD) of some respirators was observed as fumes accumulated on the filters. The present study evaluated particulate respirator PD based on workplace field tests. A field PD tester was designed and validated using the TSI 8130 Automatic Filter Tester, designed in compliance with National Institute for Occupational and Safety and Health regulation 42 CFR part 84. Three models (two replaceable dual-type filters and one replaceable single-type filter) were evaluated against CO(2) gas arc welding on mild steel in confined booths in the workplace. Field tests were performed under four airborne concentrations (27.5, 15.4, 7.9, and 2.1 mg m(-3)). The mass concentration was measured by the gravimetric method, and number concentration was monitored using P-Trak (Model 8525, TSI, USA). Additionally, photos and scanning electron microscopy-energy dispersive X-ray spectroscopy were used to visualize and analyze the composition of welding fumes trapped in the filters. The field PD tester showed no significant difference compared with the TSI tester. There was no significant difference in the initial PD between laboratory and field results. The PD increased as a function of fume load on the respirator filters for all tested models. The increasing PD trend differed by models, and PD increased rapidly at high concentrations because greater amount of fumes accumulated on the filters in a given time. The increase in PD as a function of fume load on the filters showed a similar pattern as fume load varied for a particular model, but different patterns were observed for different models. Images and elemental analyses of fumes trapped on the respirator filters showed that most welding fumes were trapped within the first layer, outer web cover, and second layer, in order, while no fumes

Occupational exposure to diesel exhaust fumes

International Nuclear Information System (INIS)

Wheatley, A. D.; Sadhra, S.

2004-01-01

There is currently no OEL for diesel fumes in the UK. This study reports parallel measurements of airborne levels of diesel fume pollutants in nine distribution depots where diesel powered fork-lift trucks (FLTs) were in use. Correlations between individual pollutants are assessed as well as their spatial distribution. Samples were collected on board FLTs and at background positions at nine distribution depots. Substances measured and the range of exposures by site were: respirable dust (n = 76) GM ≤ 80-179 μg/m 3 ; elemental carbon (n = 79) GM = 7-55 μg/m 3 ; organic carbon (n = 79) GM 11-69 μg/m 3 ; ultrafine particles (n = 17) range = 58-231 x 10 3 particles/cm 3 ; selected particulate phase polycyclic aromatic hydrocarbons (PAHs) (n - 14) range = 6-37 ng/m 3 . In addition, a tracer method based on ultrafine particle measurements was used to estimate the spatial distribution of total carbon and PAHs at the sites monitored. The spatial distribution was found to be reasonably uniform. Major diesel fume aerosol components were, in general, well correlated (r = 0.62-0.97). CO 2 measurements were also made and found to be below the HSE guideline of 1000 p.p.m., with most levels below 600 p.p.m. (Author)

A comparison between atmospheric/humidity and vacuum cyanoacrylate fuming of latent fingermarks.

Science.gov (United States)

Farrugia, Kevin J; Fraser, Joanna; Friel, Lauren; Adams, Duncan; Attard-Montalto, Nicola; Deacon, Paul

2015-12-01

A number of pseudo-operational trials were set up to compare the atmospheric/humidity and vacuum cyanoacrylate fuming processes on plastic carrier bags. The fuming processes were compared using two-step cyanoacrylate fuming with basic yellow 40 (BY40) staining and a one-step fluorescent cyanoacrylate fuming, Lumicyano 4%. Preliminary work using planted fingermarks and split depletions were performed to identify the optimum vacuum fuming conditions. The first pseudo-operational trial compared the different fuming conditions (atmospheric/humidity vs. vacuum) for the two-step process where an additional 50% more marks were detected with the atmospheric/humidity process. None of the marks by the vacuum process could be observed visually; however, a significant number of marks were detected by fluorescence after BY40 staining. The second trial repeated the same work in trial 1 using the one-step cyanoacrylate process, Lumicyano at a concentration of 4%. Trial 2 provided comparable results to trial 1 and all the items were then re-treated with Lumicyano 4% at atmospheric/humidity conditions before dyeing with BY40 to provide the sequences of process A (Lumicyano 4% atmospheric-Lumicyano 4% atmospheric-BY40) and process B (Lumicyano 4% vacuum-Lumicyano 4% atmospheric-BY40). The number of marks (visual and fluorescent) was counted after each treatment with a substantial increase in the number of detected marks in the second and third treatments of the process. The increased detection rate after the double Lumicyano process was unexpected and may have important implications. Trial 3 was performed to investigate whether the amount of cyanoacrylate and/or fuming time had an impact on the results observed in trial 2 whereas trial 4 assessed if the double process using conventional cyanoacrylate, rather than Lumicyano 4%, provided an increased detection rate. Trials 3 and 4 confirmed that doubling the amount of Lumicyano 4% cyanoacrylate and fuming time produced a lower

Response of the mouse lung transcriptome to welding fume: effects of stainless and mild steel fumes on lung gene expression in A/J and C57BL/6J mice

Directory of Open Access Journals (Sweden)

Antonini James M

2010-06-01

Full Text Available Abstract Background Debate exists as to whether welding fume is carcinogenic, but epidemiological evidence suggests that welders are an at risk population for the development of lung cancer. Recently, we found that exposure to welding fume caused an acutely greater and prolonged lung inflammatory response in lung tumor susceptible A/J versus resistant C57BL/6J (B6 mice and a trend for increased tumor incidence after stainless steel (SS fume exposure. Here, our objective was to examine potential strain-dependent differences in the regulation and resolution of the lung inflammatory response induced by carcinogenic (Cr and Ni abundant or non-carcinogenic (iron abundant metal-containing welding fumes at the transcriptome level. Methods Mice were exposed four times by pharyngeal aspiration to 5 mg/kg iron abundant gas metal arc-mild steel (GMA-MS, Cr and Ni abundant GMA-SS fume or vehicle and were euthanized 4 and 16 weeks after the last exposure. Whole lung microarray using Illumina Mouse Ref-8 expression beadchips was done. Results Overall, we found that tumor susceptibility was associated with a more marked transcriptional response to both GMA-MS and -SS welding fumes. Also, Ingenuity Pathway Analysis revealed that gene regulation and expression in the top molecular networks differed between the strains at both time points post-exposure. Interestingly, a common finding between the strains was that GMA-MS fume exposure altered behavioral gene networks. In contrast, GMA-SS fume exposure chronically upregulated chemotactic and immunomodulatory genes such as CCL3, CCL4, CXCL2, and MMP12 in the A/J strain. In the GMA-SS-exposed B6 mouse, genes that initially downregulated cellular movement, hematological system development/function and immune response were involved at both time points post-exposure. However, at 16 weeks, a transcriptional switch to an upregulation for neutrophil chemotactic genes was found and included genes such as S100A8, S100A9 and

Comparison of stainless and mild steel welding fumes in generation of reactive oxygen species

Directory of Open Access Journals (Sweden)

Frazer David

2010-11-01

Full Text Available Abstract Background Welding fumes consist of a wide range of complex metal oxide particles which can be deposited in all regions of the respiratory tract. The welding aerosol is not homogeneous and is generated mostly from the electrode/wire. Over 390,000 welders were reported in the U.S. in 2008 while over 1 million full-time welders were working worldwide. Many health effects are presently under investigation from exposure to welding fumes. Welding fume pulmonary effects have been associated with bronchitis, metal fume fever, cancer and functional changes in the lung. Our investigation focused on the generation of free radicals and reactive oxygen species from stainless and mild steel welding fumes generated by a gas metal arc robotic welder. An inhalation exposure chamber located at NIOSH was used to collect the welding fume particles. Results Our results show that hydroxyl radicals (.OH were generated from reactions with H2O2 and after exposure to cells. Catalase reduced the generation of .OH from exposed cells indicating the involvement of H2O2. The welding fume suspension also showed the ability to cause lipid peroxidation, effect O2 consumption, induce H2O2 generation in cells, and cause DNA damage. Conclusion Increase in oxidative damage observed in the cellular exposures correlated well with .OH generation in size and type of welding fumes, indicating the influence of metal type and transition state on radical production as well as associated damage. Our results demonstrate that both types of welding fumes are able to generate ROS and ROS-related damage over a range of particle sizes; however, the stainless steel fumes consistently showed a significantly higher reactivity and radical generation capacity. The chemical composition of the steel had a significant impact on the ROS generation capacity with the stainless steel containing Cr and Ni causing more damage than the mild steel. Our results suggest that welding fumes may cause acute

Synthesis And Characterization Of Pure-Silica- Zeolite-Beta Membrane

Directory of Open Access Journals (Sweden)

Yeong Yin Fong

2017-11-01

Full Text Available The semiconductor industry needs low dielectric constant (low k-value materials to more advance microprocessor and chips by reducing the size of the device features. In fabricate this context, a new material with lower k value than conventional silica ( k = 3.9 - 4.2 is needed in order to improve the circuit performance. As per the recent International Semiconductor Technology plan, a low-k material with a k = 1.6 will be needed by 2010. The choice of the inorganic zeolite membrane is an attractive option for low k material and suitable for microprocess application.  In the present study, a pure silica zeolite beta membrane coated on the non-porous stainless steel support was synthesized using in situ crystallization of a gel with the composition of  SiO2 : 0.6 TEAOH : 0.6 HF : 10.1 H2O. The crystallization was carried in the presence of tetraethylammonium hydroxide TEA(OH as structure directing agent, fumed silica, HF and deionized water at pH value of 9. The crystallization under hydrothermal conditions at 130oC was carried out for the time period of 14 days. The membrane was characterized by X-Ray Diffraction ( XRD ,  Thermogravimetric Analysis ( TGA , Nitrogen Adsorption and Scanning Electron Microscope ( SEM .   SEM micrographs show highly crystalline, truncated square bipyramidal morphology of pure silica zeolite beta was coated on the non-porous stainless steel support. The membrane dielectric constant, k-value was measured as 2.64 which makes it suitable for the microprocessor applications.

Wettability of modified silica layers deposited on glass support activated by plasma

Energy Technology Data Exchange (ETDEWEB)

Terpiłowski, Konrad, E-mail: terpil@umcs.pl [Department of Physical Chemistry – Interfacial Phenomena, Faculty of Chemistry, Maria Curie-Sklodowska University, Lublin (Poland); Rymuszka, Diana [Department of Physical Chemistry – Interfacial Phenomena, Faculty of Chemistry, Maria Curie-Sklodowska University, Lublin (Poland); Goncharuk, Olena V.; Sulym, Iryna Ya.; Gun’ko, Vladimir M. [Chuiko Institute of Surface Chemistry, National Academy of Science of Ukraine, Kiev (Ukraine)

2015-10-30

Highlights: • New modified silica materials synthesis. • Support surface plasma activation. • Apparent surface free energy determination. • Equilibrium contact angle calculation. - Abstract: Fumed silica modified by hexamethyldisilazane [HDMS] and polydimethylsiloxane [PDMS] was dispersed in a polystyrene/chloroform solution. To increase adhesion between deposited silica layers and a glass surface, the latter was pretreated with air plasma for 30 s. The silica/polystyrene dispersion was deposited on the glass support using a spin coater. After deposition, the plates were dried in a desiccator for 24 h. Water advancing and receding contact angles were measured using the tilted plate method. The apparent surface free energy (γ{sub S}) was evaluated using the contact angle hysteresis approach. The surface topography was determined using the optical profilometry method. Contact angles changed from 59.7° ± 4.4 (at surface coverage with trimethylsilyl groups Θ = 0.14) to 155° ± 3.1 at Θ = 1. The value of γ{sub S} decreased from 51.3 ± 2.8 mJ/m{sup 2} (for the sample at the lowest value of Θ) to 1.0 ± 0.4 mJ/m{sup 2} for the most hydrophobic sample. Thus, some systems with a high degree of modification by HDMS showed superhydrophobicity, and the sliding angle amounted to about 16° ± 2.1.

Designing, Constructing and Installing a Local Exhaust Ventilation System to Minimize Welders\\' Exposure to Welding Fumes

Directory of Open Access Journals (Sweden)

Sajad Zare

2017-10-01

Full Text Available Background & Aims of the Study: Welder’s exposure to welding fumes can cause occupational diseases. The current study sought to examine exposure to welding fumes among welders who work in the repair shop of Sarcheshmeh Copper Complex and design a local exhaust ventilation system to control exposure to welding fumes. Materials & Methods: This applied analytical study was conducted in the summer of 2016 among welders working in the repair shop of Sarcheshmeh Copper Complex. The study comprised three phases; in the first one, welders’ exposure to welding fumes was assessed at the beginning of the study. After that, a local exhaust ventilation system was designed and installed in the aforementioned repair shop. In the final stage, welders’ exposure to welding fumes was assessed again after installation of the ventilation system. The procedure recommended by NIOSH (method number 7300 was used for individual sampling of welders. Results: Based on the obtained findings, before installing the ventilation system, welding technicians were exposed to 0.3 mg/m3 of copper fumes and 0.04 mg/m3 of chromium fumes. Journeyman welders were also exposed to 2.16 mg/m3 of manganese fumes, while stellar welders were exposed to 6.9 mg/m3 of iron fumes. In the light of these measurements, a local exhaust ventilation system was designed and installed. Subsequently, measurement of exposure to welding fumes showed a significant reduction. That is, welding technicians were exposed to 0.17 mg/m3 and 0.015 mg/m3 of copper and chromium fumes respectively. Additionally, journeyman welders were exposed to 0.86 mg/m3 of manganese fumes, whereas stellar welders were exposed to 4.3 mg/m3 of iron fumes. Conclusions: A comparison of standard limits of exposure to welding fumes and the results obtained from measurements in sampling stations before and after the installation of the local exhaust ventilation system reveals that this controlling measure was very effective in the

Peripheral neuropathy following intentional inhalation of naphtha fumes.

Science.gov (United States)

Tenenbein, M; deGroot, W; Rajani, K R

1984-01-01

Two adolescent native Canadians who presented with peripheral neuropathy secondary to the abuse of volatile hydrocarbons are described. They were initially thought to have been sniffing leaded gasoline fumes, but public health investigation revealed that they had been sniffing naphtha fumes. Naphtha contains a significant amount of n-hexane, a known inducer of neuropathy. Nerve conduction studies and nerve biopsy confirmed the diagnosis of naphtha abuse. These cases emphasize the need to specifically identify the formulation of hydrocarbons being abused. PMID:6093978

Environmentally-Friendly Geopolymeric Binders Made with Silica

Science.gov (United States)

Erdogan, S. T.

2013-12-01

Portland cement (PC) is the ubiquitous binding material for constructions works. It is a big contributor to global warming and climate change since its production is responsible for 5-10 % of all anthropogenic CO2 emissions. Half of this emission arises from the calcination of calcareous raw materials and half from kiln fuel burning and cement clinker grinding. Recently there have been efforts to develop alternative binders with lower greenhouse gas emissions. One such class of binders is geopolymers, formed by activating natural or waste materials with suitable alkaline or acidic solutions. These binders use natural or industrial waste raw materials with a very low CO2 footprint from grinding of the starting materials, and some from the production of the activating chemicals. The total CO2 emissions from carefully formulated mixtures can be as low as 1/10th - 1/5th of those of PC concrete mixtures with comparable properties. While use of industrial wastes as raw materials is environmentally preferable, the variability of their chemical compositions over time renders their use difficult. Use of natural materials depletes resources but can have more consistent properties and can be more easily accepted. Silica sand is a natural material containing very high amounts of quartz. Silica fume is a very fine waste from silicon metal production that is mostly non-crystalline silica. This study describes the use of sodium hydroxide and sodium silicate solutions to yield mortars with mechanical properties comparable to those of portland cement mortars and with better chemical and thermal durability. Strength gain is slower than with PC mixtures at room temperature but adequate ultimate strength can be achieved with curing at slightly elevated temperatures in less than 24 h. The consistency of the chemical compositions of these materials and their abundance in several large, developing countries makes silica attractive for producing sustainable concretes with reduced carbon

Literature survey on phase composition of hardened cement paste containing fly ash

International Nuclear Information System (INIS)

Otsuka, Taku; Yamamoto, Takeshi

2015-01-01

The purpose of this literature survey is to collect the knowledge on the effect of fly ash in hardened cement paste and the information about evaluation of physicochemical performance based on phase composition of hardened cement paste. The performance of hardened cement paste containing fly ash is affected by the property of fly ash, hydration of cement and pozzolanic reaction of fly ash. Some properties of fly ash such as density and chemical composition are reflected in phase composition, showing the progress of cement hydration and pozzolanic reaction. Therefore clarification of the relationship of phase composition and performance will lead to appropriate evaluation of the property of fly ash. The amount of pore, chemical shrinkage, pore solution, compressive strength, Young modulus and alkali silica reaction have relations to the phase composition of hardened cement paste. It is considered as future subject to clarify the relationship of phase composition and performance for various properties of fly ash. (author)

Effect of curing conditions and ionic additives on properties of fly ash ...

Indian Academy of Sciences (India)

Administrator

Chemical Engineering Department, Durgapur Institute of Advanced Technology and Management,. Durgapur 713 ... Farry et al (1989) reported that the duration of the period ... Si–O bonds in the glassy, silica rich portions of fly ash. Roy and ...

In situ test plan for concrete materials using low alkaline cement at Horonobe URL

International Nuclear Information System (INIS)

Kobayashi, Yasushi; Yamada, Tsutomu; Nakayama, Masashi; Matsui, Hiroya; Matsuda, Takeshi; Konishi, Kazuhiro; Iriya, Keishiro; Noda, Masaru

2007-03-01

HLW (high-level radioactive waste) repository is to be constructed at depths of over three hundred meters below the surface. Shotcrete and lining will be used for safety under construction and operational period. Concrete is a kind of composite material which is constituted by aggregate, cement and additives. Low alkaline cement has been developed from the viewpoint of long term stability of the barrier systems which would be influenced by high alkaline arising from cement material. HFSC (Highly Fly-ash contained Silica-fume Cement) is one of a low alkaline cement, which contains silica fume and coal ash. It has been developed in Japan Atomic Energy Agency (JAEA). JAEA are now implementing the construction of the under ground research laboratory (URL) at Horonobe for the purpose of research in deep geological science and repository engineering technology. This report shows the in situ test plan for shotcrete using HFSC at Horonobe URL with identifying requirements for cement materials to be used in HLW repository, and also reviews major literatures of low alkaline cement. This in situ test plan is aiming to assess the performance of HFSC shotcrete in terms of mechanics, workability, durability, and so on. (author)

Comparative microscopic study of human and rat lungs after overexposure to welding fume.

Science.gov (United States)

Antonini, James M; Roberts, Jenny R; Schwegler-Berry, Diane; Mercer, Robert R

2013-11-01

Welding is a common industrial process used to join metals and generates complex aerosols of potentially hazardous metal fumes and gases. Most long-time welders experience some type of respiratory disorder during their time of employment. The use of animal models and the ability to control the welding fume exposure in toxicology studies have been helpful in developing a better understanding of how welding fumes affect health. There are no studies that have performed a side-by-side comparison of the pulmonary responses from an animal toxicology welding fume study with the lung responses associated with chronic exposure to welding fume by a career welder. In this study, post-mortem lung tissue was donated from a long-time welder with a well-characterized work background and a history of extensive welding fume exposure. To simulate a long-term welding exposure in an animal model, Sprague-Dawley rats were treated once a week for 28 weeks by intratracheal instillation with 2mg of a stainless steel, hard-surfacing welding fume. Lung tissues from the welder and the welding fume-treated rats were examined by light and electron microscopy. Pathological analysis of lung tissue collected from the welder demonstrated inflammatory cell influx and significant pulmonary injury. The poor and deteriorating lung condition observed in the welder examined in this study was likely due to exposure to very high levels of potentially toxic metal fumes and gases for a significant number of years due to work in confined spaces. The lung toxicity profile for the rats treated with welding fume was similar. For tissue samples from both the welder and treated rats, welding particle accumulations deposited and persisted in lung structures and were easily visualized using light microscopic techniques. Agglomerates of deposited welding particles mostly were observed within lung cells, particularly alveolar macrophages. Analysis of individual particles within the agglomerates showed that these

30 CFR 70.305 - Respiratory equipment; gas, dusts, fumes, or mists.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Respiratory Equipment § 70.305 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by...

Physical, Mechanical, Thermal and Morphology Properties of Biodegradable Polymer Nanocomposites and Its Comparison

Directory of Open Access Journals (Sweden)

Rahman Md. Rezaur

2017-01-01

Full Text Available Polyvinyl alcohol (PVA and Polylactic acid (PLA were fabricated with the addition of nanofiller such as nanoclay and fumed silica through suitable technique namely solution intercalation film casting. These nanocomposites undergo Fourier transform infrared spectroscopy, scanning electron microscopy, tensile test and thermogravimetric analysis. FT-IR results showed that both nanocomposites were well intercalated with fumed silica and clay with the reduction of hydroxyl groups. From SEM results, it proved that clay 1.28E is more suitable to be intercalated with PLA matrix while clay 1.30E is more suitable to be introduced into PVA matrix. The addition of both nanofillers improved the tensile properties of the nanocomposites. TGA results showed that polyvinyl alcohol/fumed silica/clay (PVA/fsi/clay had better thermal stability compared to polylactic acid/fumed silica/clay (PLA/fsi/clay nanocomposites. Both nanocomposites are applicable in the biomedical field.

Fatigue Behavior of Modified Asphalt Concrete Pavement

Directory of Open Access Journals (Sweden)

saad I. Sarsam

2016-02-01

Full Text Available Fatigue cracking is the most common distress in road pavement. It is mainly due to the increase in the number of load repetition of vehicles, particularly those with high axle loads, and to the environmental conditions. In this study, four-point bending beam fatigue testing has been used for control and modified mixture under various micro strain levels of (250 μƐ, 400 μƐ, and 750 μƐ and 5HZ. The main objective of the study is to provide a comparative evaluation of pavement resistance to the phenomenon of fatigue cracking between modified asphalt concrete and conventional asphalt concrete mixes (under the influence of three percentage of Silica fumes 1%, 2%, 3% by the weight of asphalt content, and (changing in the percentage of asphalt content by (0.5% ± from the optimum. The results show that when Silica fumes content was 1%, the fatigue life increases by 17%, and it increases by 46% when Silica fumes content increases to 2%, and that fatigue life increases to 34 % when Silica fumes content increases to 3% as compared with control mixture at (250 μƐ, 20°C and optimum asphalt content. From the results above, we can conclude the optimum Silica fumes content was 2%. When the asphalt content was 4.4%, the fatigue life has increased with the use of silica fumes by (50%, when asphalt content was 5.4%, the additives had led to increasing the fatigue life by (69%, as compared with the conventional asphalt concrete pavement.

Modifying welding process parameters can reduce the neurotoxic potential of manganese-containing welding fumes.

Science.gov (United States)

Sriram, Krishnan; Lin, Gary X; Jefferson, Amy M; Stone, Samuel; Afshari, Aliakbar; Keane, Michael J; McKinney, Walter; Jackson, Mark; Chen, Bean T; Schwegler-Berry, Diane; Cumpston, Amy; Cumpston, Jared L; Roberts, Jenny R; Frazer, David G; Antonini, James M

2015-02-03

Welding fumes (WF) are a complex mixture of toxic metals and gases, inhalation of which can lead to adverse health effects among welders. The presence of manganese (Mn) in welding electrodes is cause for concern about the potential development of Parkinson's disease (PD)-like neurological disorder. Consequently, from an occupational safety perspective, there is a critical need to prevent adverse exposures to WF. As the fume generation rate and physicochemical characteristics of welding aerosols are influenced by welding process parameters like voltage, current or shielding gas, we sought to determine if changing such parameters can alter the fume profile and consequently its neurotoxic potential. Specifically, we evaluated the influence of voltage on fume composition and neurotoxic outcome. Rats were exposed by whole-body inhalation (40 mg/m(3); 3h/day × 5 d/week × 2 weeks) to fumes generated by gas-metal arc welding using stainless steel electrodes (GMA-SS) at standard/regular voltage (25 V; RVSS) or high voltage (30 V; HVSS). Fumes generated under these conditions exhibited similar particulate morphology, appearing as chain-like aggregates; however, HVSS fumes comprised of a larger fraction of ultrafine particulates that are generally considered to be more toxic than their fine counterparts. Paradoxically, exposure to HVSS fumes did not elicit dopaminergic neurotoxicity, as monitored by the expression of dopaminergic and PD-related markers. We show that the lack of neurotoxicity is due to reduced solubility of Mn in HVSS fumes. Our findings show promise for process control procedures in developing prevention strategies for Mn-related neurotoxicity during welding; however, it warrants additional investigations to determine if such modifications can be suitably adapted at the workplace to avert or reduce adverse neurological risks. Published by Elsevier Ireland Ltd.

Modifying welding process parameters can reduce the neurotoxic potential of manganese-containing welding fumes

International Nuclear Information System (INIS)

Sriram, Krishnan; Lin, Gary X.; Jefferson, Amy M.; Stone, Samuel; Afshari, Aliakbar; Keane, Michael J.; McKinney, Walter; Jackson, Mark; Chen, Bean T.; Schwegler-Berry, Diane; Cumpston, Amy; Cumpston, Jared L.; Roberts, Jenny R.; Frazer, David G.; Antonini, James M.

2015-01-01

Welding fumes (WF) are a complex mixture of toxic metals and gases, inhalation of which can lead to adverse health effects among welders. The presence of manganese (Mn) in welding electrodes is cause for concern about the potential development of Parkinson’s disease (PD)-like neurological disorder. Consequently, from an occupational safety perspective, there is a critical need to prevent adverse exposures to WF. As the fume generation rate and physicochemical characteristics of welding aerosols are influenced by welding process parameters like voltage, current or shielding gas, we sought to determine if changing such parameters can alter the fume profile and consequently its neurotoxic potential. Specifically, we evaluated the influence of voltage on fume composition and neurotoxic outcome. Rats were exposed by whole-body inhalation (40 mg/m 3 ; 3 h/day × 5 d/week × 2 weeks) to fumes generated by gas–metal arc welding using stainless steel electrodes (GMA-SS) at standard/regular voltage (25 V; RVSS) or high voltage (30 V; HVSS). Fumes generated under these conditions exhibited similar particulate morphology, appearing as chain-like aggregates; however, HVSS fumes comprised of a larger fraction of ultrafine particulates that are generally considered to be more toxic than their fine counterparts. Paradoxically, exposure to HVSS fumes did not elicit dopaminergic neurotoxicity, as monitored by the expression of dopaminergic and PD-related markers. We show that the lack of neurotoxicity is due to reduced solubility of Mn in HVSS fumes. Our findings show promise for process control procedures in developing prevention strategies for Mn-related neurotoxicity during welding; however, it warrants additional investigations to determine if such modifications can be suitably adapted at the workplace to avert or reduce adverse neurological risks

Accelerated hydration of high silica cements

International Nuclear Information System (INIS)

Walker, Colin; Yui, Mikazu

2012-01-01

Current Japanese designs for high level radioactive waste (HLW) repositories anticipate the use of both bentonite (buffer and backfill material) and cement based materials. Using hydrated Ordinary Portland Cement (OPC) as a grouting material is undesirable because the associated high pH buffer will have an undisputed detrimental effect on the performance of the bentonite buffer and backfill and of the host rock by changing its porosity. Instead, hydrated low pH cement (LopHC) grouting materials are being developed to provide a pH inferior or equal to 11 to reduce these detrimental effects. LopHC grouting materials use mixtures of superfine OPC (SOPC) clinker and silica fume (SF), and are referred as high silica cements (HSC). The focus of the present study was to identify the development of the unhydrated and hydrated mineral assemblage and the solution chemistry during the hydration of HSC. Since hydration experiments of cementitious materials are notably slow, a ball mill was used to accelerate hydration. This was done for two reasons. Firstly, to develop a method to rapidly hydrate cement based materials without the need for higher temperatures (which can alter the mineral assemblage), and secondly, to ensure that the end point of hydration was reached in a reasonable time frame and so to realize the final mineralogy and solution chemistry of hydrated HSC

Rapid Synthesis and Characterization of Nano sodalite Synthesized using Rice Husk Ash

International Nuclear Information System (INIS)

Siti Haslina Ahmad Rusmili; Zainab Ramli

2012-01-01

Rice husk ash (RHA) which contains more than 90 percent silica is proven to be an active silica source in zeolite synthesis. In this study, nano sodalite has been successfully synthesized hydrothermally at 60 degree Celsius using RHA as silica source in alkaline medium at various crystallization times. Commercial fumed silica was used as comparison for the silica source. Analysis by XRD has shown that pure nano sodalite was formed in 3 hours and stable up to more than 24 hours when using RHA as silica source. On the other hand, fumed silica produced pure nano sodalite only at 4 hours while a mixture of zeolites was observed outside this time range. FESEM shows a worm-like morphology of nano sodalite in the size range of 50-100 nm while FTIR shows the formation of aluminosilicates bonds. Analysis on the dissolved silica in the gel reaction mixture demonstrates the decreasing mass of silica after prolong time of crystallization which indicates the consumption of the dissolved silica in crystal growth of nano sodalite. This study shows that RHA is a better silica source in stabilizing the nano sodalite phase in oxide gel reaction mixture as compared to fumed silica. (author)

On the effect of mixing on property development of cement pastes

DEFF Research Database (Denmark)

Geiker, Mette Rica; Bøhm, Anja; Kjeldsen, Ane Mette

2006-01-01

by hand and in a high-speed mixer. Chemical shrinkage was measured to illustrate the effect of mixing on development of hydration. Chloride migration was measured on 28 days old pastes to illustrate the effect of mixing on the hydrated pastes. The present investigation of pastes of white Portland cement...... showed an effect of mixing on the development of chemical shrinkage, i.e. hydration, of pastes with superplasticizer, but without silica fume. Silica fume agglomerates were observed in thin sections of pastes with silica fume and mixed by hand; however no effect on the development of hydration...

Risk of ischemic heart disease following occupational exposure to welding fumes

DEFF Research Database (Denmark)

Mocevic, Emina; Kristiansen, Pernille; Bonde, Jens Peter

2015-01-01

PURPOSE: Air pollution has been linked to an increased risk of ischemic heart disease (IHD), but less is known about occupational exposure to welding fumes and the risk of IHD. The objective of this paper was to review the epidemiological evidence on causal links between welding fume exposure...

Anatomical indications of fume resistance in certain woody plants

Energy Technology Data Exchange (ETDEWEB)

Ninova, D.

1970-01-01

An attempt is made to describe studies on seven species of fruit and forest trees close to or far from a Bulgarian factory emitting fumes containing S. The most resistant species (Quercus borealis, Gleditsia triacanthos, Morus alba) had the smallest stomata and the greatest number of stomata per unit leaf area. Changes observed in leaf anatomy as a result of exposure to the fumes were: decreased leaf aeration, elongated palisade cells, thicker cuticles, and more stomata.

Hepatotoxicity and genotoxicity of gasoline fumes in albino rats

Directory of Open Access Journals (Sweden)

Folarin O. Owagboriaye

2017-09-01

Full Text Available Toxic effects of gasoline fumes have been reported, but evidence of its hepatotoxicity and genotoxicity are rare. Therefore, this study assesses hepatotoxicity and genotoxicity of gasoline fumes on forty Albino rats randomly assigned to five experimental treatments (T with eight rats per treatment (T1, T2, T3, T4 and T5. T1(Control was housed in a section of experimental animal house free from gasoline fumes while T2, T3, T4 and T5 were exposed to gasoline fumes in exposure chambers for one, three, five and nine hours daily respectively for twelve weeks. Serum alanine aminotransferase (ALT, aspartate aminotransferase (AST, alkaline phosphatase (ALP and histopathological examination of the liver tissues were used as diagnostic markers to assess liver dysfunction. Genotoxicity test was conducted on the lung tissues using randomly amplified polymorphic DNA fingerprinting polymerase chain reaction (RAPD PCR technique. Significant increase (p < 0.05 in the level of ALT, AST and ALP for T2, T3, T4 and T5 compared to T1 were recorded. Photomicrograph examination of the liver sections of T1 showed hepatic tissue with normal liver cell architecture while that of T2, T3, T4 and T5 revealed degenerative changes in the ultrastructural integrity of the hepatic cells. Genotoxicity test revealed DNA bands at a reducing intensity from T1 to T5. Dendrogram showed DNA damage in the lungs of T3, T4 and T5 were closely similar and the genotoxic impact was more in T3. Frequent exposure to gasoline fumes was observed to induce hepatoxicity and genotoxicity, hence impairing the normal liver function and gene structure.

Compressive strength improvement for recycled concrete aggregate

Directory of Open Access Journals (Sweden)

Mohammed Dhiyaa

2018-01-01

Full Text Available Increasing amount of construction waste and, concrete remnants, in particular pose a serious problem. Concrete waste exist in large amounts, do not decay and need long time for disintegration. Therefore, in this work old demolished concrete is crashed and recycled to produce recycled concrete aggregate which can be reused in new concrete production. The effect of using recycled aggregate on concrete compressive strength has been experimentally investigated; silica fume admixture also is used to improve recycled concrete aggregate compressive strength. The main parameters in this study are recycled aggregate and silica fume admixture. The percent of recycled aggregate ranged from (0-100 %. While the silica fume ranged from (0-10 %. The experimental results show that the average concrete compressive strength decreases from 30.85 MPa to 17.58 MPa when the recycled aggregate percentage increased from 0% to 100%. While, when silica fume is used the concrete compressive strength increase again to 29.2 MPa for samples with 100% of recycled aggregate.

Characterisation of fume from hyperbaric welding operations

Energy Technology Data Exchange (ETDEWEB)

Ross, John A S; Semple, Sean [Environmental and Occupational Medicine, University of Aberdeen (United Kingdom); Duffin, Rodger [ELEGI Colt Laboratory, University of Edinburgh (United Kingdom); Kelly, Frank [Lung Biology Group, Kings College, University of London (United Kingdom); Seldmann, Joerg; Raab, Andrea, E-mail: j.a.ross@abdn.ac.u [Trace Element Speciation Laboratory, University of Aberdeen (United Kingdom)

2009-02-01

We report preliminary work characterising dust from hyperbaric welding trials carried out at increased pressure in a helium and oxygen atmosphere. Particle size and concentration were measured during welding. Samples for quartz and metal analysis and toxicity assessment were taken from a filter in the local fume extraction system. The residue of dust after metal extraction by nitric acid in hydrogen peroxide predominantly a non-metallic white powder assumed to be dust from welding rod coatings and thermal insulation material. Metallic analysis showed predominantly calcium, from the welding rod coating, and period 4 transition metals such as iron, manganese, magnesium and titanium (inductively coupled mass spectrometry, Agilent 7500c). The presence of zirconium indicated a contribution from grinding. The fume was nanoparticulate in nature with a mean particle diameter of 20-30 nm (MSI Inc WPS 1000XP). It showed an intermediate level of oxidative potential regarding the low-molecular weight respiratory tract lining fluid antioxidants ascorbate and glutathione and caused release of the inflammatory marker IL-8 in a human lung A 549 epithelial cell culture with no indication of cytotoxicity. The study findings have strong implications for the measurement techniques needed to assess fume exposure in hyperbaric welding and the provision of respiratory protection.

Short term exposure to cooking fumes and pulmonary function

OpenAIRE

Qvenild Torgunn; Svendsen Kristin; Svedahl Sindre; Sjaastad Ann; Hilt Bjørn

2009-01-01

Abstract Background Exposure to cooking fumes may have different deleterious effects on the respiratory system. The aim of this study was to look at possible effects from inhalation of cooking fumes on pulmonary function. Methods Two groups of 12 healthy volunteers (A and B) stayed in a model kitchen for two and four hours respectively, and were monitored with spirometry four times during twenty four hours, on one occasion without any exposure, and on another with exposure to controlled level...

42 CFR 84.1141 - Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Science.gov (United States)

2010-10-01

... mist respirators designed for respiratory protection against fumes of various metals having an air... HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist....1141 Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Ultra high performance concrete made with rice husk ash for reduced autogenous shrinkage

NARCIS (Netherlands)

Van Breugel, K.; Van Tuan, N.

2014-01-01

Ultra High Strength Concrete (UHPC) is generally made with low w/c mixtures and by adding silica fume. Low w/c mixtures, however, exhibit high autogenous shrinkage, while a high amount of silica fume increases the price of these mixtures. For designing ultra high strength mixtures with low

Profiling mild steel welding processes to reduce fume emissions and costs in the workplace.

Science.gov (United States)

Keane, Michael J; Siert, Arlen; Chen, Bean T; Stone, Samuel G

2014-05-01

To provide quantitative information to choose the best welding processes for minimizing workplace emissions, nine gas metal arc welding (GMAW) processes for mild steel were assessed for fume generation rates, normalized fume generation rates (milligram fume per gram of electrode consumed), and normalized generation rates for elemental manganese, nickel, and iron. Shielded metal arc welding (SMAW) and flux-cored arc-welding (FCAW) processes were also profiled. The fumes were collected quantitatively in an American Welding Society-type fume chamber and weighed, recovered, homogenized, and analyzed by inductively coupled atomic emission spectroscopy for total metals. The processes included GMAW with short circuit, globular transfer, axial spray, pulsed spray, Surface Tension Transfer™, Regulated Metal Deposition™, and Cold Metal Transfer™ (CMT) modes. Flux-cored welding was gas shielded, and SMAW was a single rod type. Results indicate a wide range of fume emission factors for the process variations studied. Fume emission rates per gram of electrode consumed were highest for SMAW (~13 mg fume g(-1) electrode) and lowest for GMAW processes such as pulsed spray (~1.5mg g(-1)) and CMT (~1mg g(-1)). Manganese emission rates per gram of electrode consumed ranged from 0.45 mg g(-1) (SMAW) to 0.08 mg g(-1) (CMT). Nickel emission rates were generally low and ranged from ~0.09 (GMAW short circuit) to 0.004 mg g(-1) (CMT). Iron emission rates ranged from 3.7 (spray-mode GMAW) to 0.49 mg g(-1) (CMT). The processes studied have significantly different costs, and cost factors are presented based on a case study to allow comparisons between processes in specific cost categories. Costs per linear meter of weld were $31.07 (SMAW), $12.37 (GMAW short circuit), and $10.89 (FCAW). Although no single process is the best for minimizing fume emissions and costs while satisfying the weld requirements, there are several processes that can minimize emissions. This study provides

Can superabsorbent polymers mitigate shrinkage in cementitious materials blended with supplementary cementitious materials?

DEFF Research Database (Denmark)

Snoeck, Didier; Jensen, Ole Mejlhede; De Belie, Nele

2016-01-01

A promising way to mitigate autogenous shrinkage in cementitious materials with a low water-to-binder ratio is internal curing by the use of superabsorbent polymers. Superabsorbent polymers are able to absorb multiple times their weight in water and can be applied as an internal water reservoir...... to induce internal curing and mitigation of self-desiccation. Their purposefulness has been demonstrated in Portland cement pastes with and without silica fume. Nowadays, fly ash and blast-furnace slag containing binders are also frequently used in the construction industry. The results on autogenous...... shrinkage in materials blended with fly ash or blast-furnace slag remain scarce, especially after one week of age. This paper focuses on the autogenous shrinkage by performing manual and automated shrinkage measurements up to one month of age. Without superabsorbent polymers, autogenous shrinkage...

Determination of the Fracture Energy of Concrete

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place; Stang, Henrik

1998-01-01

In a NORDTEST project two methods for determination of the fracture energy of concrete are compared; the Three-Point Bend Test (TPBT) and the Wedge Splitting Test (WST). The methods involve notched beams and notched, grooved cubes, respectively. The two methods are compared in relation to handling...... and precision (repeatability, reproducibility). Concrete with a water/cement ratio of 0.43 including fly ash as well as silica fume is investigated. The results show that WST is significantly faster to work with compared to TPBT, although the sawing procedure is more time consuming. Only when using laboratory...

Study of a proprietory Pozzolanic product. Technical report

International Nuclear Information System (INIS)

Buck, A.D.

1981-05-01

Petrographic examination and limited chemical analysis were used to identify constituents in a proprietary anti-corrosion admixture (AD-644) for concrete. Petrographic examination included x-ray diffraction, light microscopy, and scanning electron microscopy. The CaO content of the sample was determined by chemical analysis as a basis for estimating cement content of the sample. Results indicated that the admixture was largely silica fume containing about 12% portland cement and a small amount of organic material which was believed to be a water-reducing admixture. Properties of a known silica fume (AD-536(2)) were used as a basis for concluding that silica fume was the principal constituent and this admixture

Exposure to inhalable, respirable, and ultrafine particles in welding fume.

Science.gov (United States)

Lehnert, Martin; Pesch, Beate; Lotz, Anne; Pelzer, Johannes; Kendzia, Benjamin; Gawrych, Katarzyna; Heinze, Evelyn; Van Gelder, Rainer; Punkenburg, Ewald; Weiss, Tobias; Mattenklott, Markus; Hahn, Jens-Uwe; Möhlmann, Carsten; Berges, Markus; Hartwig, Andrea; Brüning, Thomas

2012-07-01

This investigation aims to explore determinants of exposure to particle size-specific welding fume. Area sampling of ultrafine particles (UFP) was performed at 33 worksites in parallel with the collection of respirable particles. Personal sampling of respirable and inhalable particles was carried out in the breathing zone of 241 welders. Median mass concentrations were 2.48 mg m(-3) for inhalable and 1.29 mg m(-3) for respirable particles when excluding 26 users of powered air-purifying respirators (PAPRs). Mass concentrations were highest when flux-cored arc welding (FCAW) with gas was applied (median of inhalable particles: 11.6 mg m(-3)). Measurements of particles were frequently below the limit of detection (LOD), especially inside PAPRs or during tungsten inert gas welding (TIG). However, TIG generated a high number of small particles, including UFP. We imputed measurements welding fume. Concentrations were mainly predicted by the welding process and were significantly higher when local exhaust ventilation (LEV) was inefficient or when welding was performed in confined spaces. Substitution of high-emission techniques like FCAW, efficient LEV, and using PAPRs where applicable can reduce exposure to welding fume. However, harmonizing the different exposure metrics for UFP (as particle counts) and for the respirable or inhalable fraction of the welding fume (expressed as their mass) remains challenging.

Alterations in welding process voltage affect the generation of ultrafine particles, fume composition, and pulmonary toxicity.

Science.gov (United States)

Antonini, James M; Keane, Michael; Chen, Bean T; Stone, Samuel; Roberts, Jenny R; Schwegler-Berry, Diane; Andrews, Ronnee N; Frazer, David G; Sriram, Krishnan

2011-12-01

The goal was to determine if increasing welding voltage changes the physico-chemical properties of the fume and influences lung responses. Rats inhaled 40 mg/m³ (3 h/day × 3 days) of stainless steel (SS) welding fume generated at a standard voltage setting of 25 V (regular SS) or at a higher voltage (high voltage SS) of 30 V. Particle morphology, size and composition were characterized. Bronchoalveolar lavage was performed at different times after exposures to assess lung injury. Fumes collected from either of the welding conditions appeared as chain-like agglomerates of nanometer-sized primary particles. High voltage SS welding produced a greater number of ultrafine-sized particles. Fume generated by high voltage SS welding was higher in manganese. Pulmonary toxicity was more substantial and persisted longer after exposure to the regular SS fume. In summary, a modest raise in welding voltage affected fume size and elemental composition and altered the temporal lung toxicity profile.

deFUME: Dynamic exploration of functional metagenomic sequencing data

DEFF Research Database (Denmark)

van der Helm, Eric; Geertz-Hansen, Henrik Marcus; Genee, Hans Jasper

2015-01-01

is time consuming and constitutes a major bottleneck for experimental researchers in the field. Here we present the deFUME web server, an easy-to-use web-based interface for processing, annotation and visualization of functional metagenomics sequencing data, tailored to meet the requirements of non......-bioinformaticians. The web-server integrates multiple analysis steps into one single workflow: read assembly, open reading frame prediction, and annotation with BLAST, InterPro and GO classifiers. Analysis results are visualized in an online dynamic web-interface. The deFUME webserver provides a fast track from raw sequence...

Synthesis and investigation of sorbing materials based on natural and synthetic dispersed oxide systems for sorbing active leaching products of lava-like fuel-containing materials

International Nuclear Information System (INIS)

Kryip, Yi.M.; Shimchuk, T.V.; Tokarchuk, M.V.; Tokarchuk, M.V.

2004-01-01

Laboratory sorbent samples were synthesized on the basis of modified natural clayey raw material and fumed silica. Using chemical methods, composition of synthesized sorbents was established. Oxide and hydroxide structures, plated on the fumed silica and natural montmorillonite clay surface were identified. A forecast about sorbing properties of synthesized materials is made

Reduction of Biomechanical and Welding Fume Exposures in Stud Welding.

Science.gov (United States)

Fethke, Nathan B; Peters, Thomas M; Leonard, Stephanie; Metwali, Mahmoud; Mudunkotuwa, Imali A

2016-04-01

The welding of shear stud connectors to structural steel in construction requires a prolonged stooped posture that exposes ironworkers to biomechanical and welding fume hazards. In this study, biomechanical and welding fume exposures during stud welding using conventional methods were compared to exposures associated with use of a prototype system that allowed participants to weld from an upright position. The effect of base material (i.e. bare structural beam versus galvanized decking) on welding fume concentration (particle number and mass), particle size distribution, and particle composition was also explored. Thirty participants completed a series of stud welding simulations in a local apprenticeship training facility. Use of the upright system was associated with substantial reductions in trunk inclination and the activity levels of several muscle groups. Inhalable mass concentrations of welding fume (averaged over ~18 min) when using conventional methods were high (18.2 mg m(-3) for bare beam; 65.7 mg m(-3) for through deck), with estimated mass concentrations of iron (7.8 mg m(-3) for bare beam; 15.8 mg m(-3) for through deck), zinc (0.2 mg m(-3) for bare beam; 15.8 mg m(-3) for through deck), and manganese (0.9 mg m(-3) for bare beam; 1.5 mg m(-3) for through deck) often exceeding the American Conference of Governmental Industrial Hygienists Threshold Limit Values (TLVs). Number and mass concentrations were substantially reduced when using the upright system, although the total inhalable mass concentration remained above the TLV when welding through decking. The average diameters of the welding fume particles for both bare beam (31±17 nm) through deck conditions (34±34 nm) and the chemical composition of the particles indicated the presence of metallic nanoparticles. Stud welding exposes ironworkers to potentially high levels of biomechanical loading (primarily to the low back) and welding fume. The upright system used in this study improved exposure

The Effect of HCWA-PFA Hybrid Geopolymer Modification on the Properties of Soil

OpenAIRE

Hassian F.F.; Cheah C.C.

2014-01-01

This study investigated the performance of the properties of foamed concrete when replacing volumes of cement of 10%, 15% and 20% by weight. A control unit of foamed concrete mixture made with Ordinary Portland Cement (OPC) as well as samples containing 10%, 15% and 20% silica fume were prepared. Three mechanical property parameters of foamed concrete containing different percentages of silica fume were studied: compressive strength, flexural strength and splitting tensile strength. Silica fu...

Exposure to Cooking Fumes and Acute Reversible Decrement in Lung Functional Capacity.

Science.gov (United States)

Neghab, Masoud; Delikhoon, Mahdieh; Norouzian Baghani, Abbas; Hassanzadeh, Jafar

2017-10-01

Being exposed to cooking fumes, kitchen workers are occupationally at risk of multiple respiratory hazards. No conclusive evidence exists as to whether occupational exposure to these fumes is associated with acute and chronic pulmonary effects and symptoms of respiratory diseases. To quantify the exposure levels and evaluate possible chronic and acute pulmonary effects associated with exposure to cooking fumes. In this cross-sectional study, 60 kitchen workers exposed to cooking fumes and 60 unexposed employees were investigated. The prevalence of respiratory symptoms among these groups was determined through completion of a standard questionnaire. Pulmonary function parameters were also measured before and after participants' work shift. Moreover, air samples were collected and analyzed to quantify their aldehyde, particle, and volatile organic contents. The mean airborne concentrations of formaldehyde, acetaldehyde, and acrolein was 0.45 (SD 0.41), 0.13 (0.1), and 1.56 (0.41) mg/m 3 , respectively. The mean atmospheric concentrations of PM 1 , PM 2.5 , PM 7 , PM 10 , and total volatile organic compounds (TVOCs) was 3.31 (2.6), 12.21 (5.9), 44.16 (16.6), 57 (21.55) μg/m 3 , and 1.31 (1.11) mg/m 3 , respectively. All respiratory symptoms were significantly (pcooking fumes is associated with a significant increase in the prevalence of respiratory symptoms as well as acute reversible decrease in lung functional capacity.

Transport and Deposition of Welding Fume Agglomerates in a Realistic Human Nasal Airway.

Science.gov (United States)

Tian, Lin; Inthavong, Kiao; Lidén, Göran; Shang, Yidan; Tu, Jiyuan

2016-07-01

Welding fume is a complex mixture containing ultra-fine particles in the nanometer range. Rather than being in the form of a singular sphere, due to the high particle concentration, welding fume particles agglomerate into long straight chains, branches, or other forms of compact shapes. Understanding the transport and deposition of these nano-agglomerates in human respiratory systems is of great interest as welding fumes are a known health hazard. The neurotoxin manganese (Mn) is a common element in welding fumes. Particulate Mn, either as soluble salts or oxides, that has deposited on the olfactory mucosa in human nasal airway is transported along the olfactory nerve to the olfactory bulb within the brain. If this Mn is further transported to the basal ganglia of the brain, it could accumulate at the part of the brain that is the focal point of its neurotoxicity. Accounting for various dynamic shape factors due to particle agglomeration, the current computational study is focused on the exposure route, the deposition pattern, and the deposition efficiency of the inhaled welding fume particles in a realistic human nasal cavity. Particular attention is given to the deposition pattern and deposition efficiency of inhaled welding fume agglomerates in the nasal olfactory region. For particles in the nanoscale, molecular diffusion is the dominant transport mechanism. Therefore, Brownian diffusion, hydrodynamic drag, Saffman lift force, and gravitational force are included in the model study. The deposition efficiencies for single spherical particles, two kinds of agglomerates of primary particles, two-dimensional planar and straight chains, are investigated for a range of primary particle sizes and a range of number of primary particles per agglomerate. A small fraction of the inhaled welding fume agglomerates is deposited on the olfactory mucosa, approximately in the range 0.1-1%, and depends on particle size and morphology. The strong size dependence of the deposition

Compressive strength of concrete by partial replacement of cement with metakaolin

Science.gov (United States)

Ganesh, Y. S. V.; Durgaiyya, P.; Shivanarayana, Ch.; Prasad, D. S. V.

2017-07-01

Metakaolin or calcined kaolin, other type of pozzolan, produced by calcination has the capability to replace silica fume as an alternative material. Supplementary cementitious materials have been widely used all over the world in concrete due to their economic and environmental benefits; hence, they have drawn much attention in recent years. Mineral admixtures such as fly ash, rice husk ash, silica fume etc. are more commonly used SCMs. They help in obtaining both higher performance and economy. Metakaolin is also one of such non - conventional material, which can be utilized beneficially in the construction industry. This paper presents the results of an experimental investigations carried out to find the suitability of metakaolin in production of concrete. In the present work, the results of a study carried out to investigate the effects of Metakaolin on compressive strength of concrete are presented. The referral concrete M30 was made using 43 grade OPC and the other mixes were prepared by replacing part of OPC with Metakaolin. The replacement levels were 5%, 10%, 15% and 20%(by weight) for Metakaolin. The various results, which indicate the effect of replacement of cement by metakalion on concrete, are presented in this paper to draw useful conclusions.

Development of high-performance concrete having high resistance to chloride penetration

International Nuclear Information System (INIS)

Oh, Byung Hwan; Cha, Soo Won; Jang, Bong Seok; Jang, Seung Yup

2002-01-01

The resistance to chloride penetration is one of the simplest measures to determine the durability of concrete, e.g. resistance to freezing and thawing, corrosion of steel in concrete and other chemical attacks. Thus, high-performance concrete may be defined as the concrete having high resistance to chloride penetration as well as high strength. The purpose of this paper is to investigate the resistance to chloride penetration of different types of concrete and to develop high-performance concrete that has very high resistance to chloride penetration, and thus, can guarantee high durability. A large number of concrete specimens have been tested by the rapid chloride permeability test method as designated in AASHTO T 277 and ASTM C 1202. The major test variables include water-to-binder ratios, type of cement, type and amount of mineral admixtures (silica fume, fly ash and blast-furnace slag), maximum size of aggregates and air-entrainment. Test results show that concrete containing optimal amount of silica fume shows very high resistance to chloride penetration, and high-performance concrete developed in this study can be efficiently employed to enhance the durability of concrete structures in severe environments such as nuclear power plants, water-retaining structures and other offshore structures

Engineering Properties and Correlation Analysis of Fiber Cementitious Materials

Directory of Open Access Journals (Sweden)

Wei-Ting Lin

2014-11-01

Full Text Available This study focuses on the effect of the amount of silica fume addition and volume fraction of steel fiber on the engineering properties of cementitious materials. Test variables include dosage of silica fume (5% and 10%, water/cement ratio (0.35 and 0.55 and steel fiber dosage (0.5%, 1.0% and 2.0%. The experimental results included: compressive strength, direct tensile strength, splitting tensile strength, surface abrasion and drop-weight test, which were collected to carry out the analysis of variance to realize the relevancy and significance between material parameters and those mechanical properties. Test results illustrate that the splitting tensile strength, direct tensile strength, strain capacity and ability of crack-arresting increase with increasing steel fiber and silica fume dosages, as well as the optimum mixture of the fiber cementitious materials is 5% replacement silica fume and 2% fiber dosage. In addition, the Pearson correlation coefficient was conducted to evaluate the influence of the material variables and corresponds to the experiment result.

The heterogeneous nature of mineral matter, fly-ash and deposits

Energy Technology Data Exchange (ETDEWEB)

Creelman, R.A.; Pohl, J.H.; Devir, G.P.; Su, S. [R.A. Creelman and Associates, Epping, NSW (Australia)

2000-07-01

This paper reports on a series of slagging studies investigating the heterogeneous nature of mineral matter, fly ash and deposits, and how this heterogeneity affects deposition. The data come from low temperature ashing (LTA) of pulverised coal, fly ash from boilers, and deposits from pilot-scale furnaces and boilers. The paper presents optical and scanning electron (SEM) micrographs, electron microprobe analysis (EMPA) and energy dispersive x-ray analysis (EDXRA) of mineral matter, individual fly ash particles, and localised regions of deposits. During combustion, the included mineral matter is transformed into fly ash, melts and partially adheres to the char surface, and may form agglomerated masses. Excluded mineral matter has little chance of encountering another ash particle and agglomerating in the gas phase, but can react with other particles in the wall deposits. Certain fly ash particles adhere to the wall where they can combine with other fly ash particles. Analyses of molten regions of deposits have shown, so far, four mineral phase fields to be responsible for forming difficult deposits with melting points below deposit surface temperatures of 1200 to 1350{sup o}C. These mineral fields include iron cordierite, albite and its silica undersaturated equivalent nepheline, anorthite, and compounds with ratios of Ca to P of 2.3-2.5.

Genotoxic Effects of Exposure to Gasoline Fumes on Petrol Pump Workers

OpenAIRE

Amrin Shaikh; Darshana Barot; Divya Chandel

2018-01-01

Background: Petrol pump workers are occupationally exposed to gasoline and its fumes consisting of several mutagenic chemicals. Objective: To evaluate the genotoxic effects of exposure to gasoline fumes on petrol pump workers. Methods: The study groups included 70 petrol pump workers (exposed group) and 70 healthy age-matched individuals with no known exposure (comparison group). Buccal micronucleus cytome assay (BMCyt) was performed to check the genotoxicity caused due to inhalation ...

The influence of the amount addition and kind of the active silica fume in the mechanical properties of the cement Portland concrete

International Nuclear Information System (INIS)

Silva, I.J. da; Melo, A.B. de; Liborio, J.B.L.; Souza, M.F. de

1998-01-01

This study presents an evaluation of the influence of the amount addition and of active silica type deriving from residues of the production of Iron-Silicon alloys of brasilian industries, on the mechanical properties of the concrete made with basaltic aggregates with D max ≥9,5 mm using Portland cements CP II E 32. The study has for objective to evaluate the efficiency of the active silica on the mechanical resistance of the high performance concrete (CAD), when used in substitution of the Portland cement, even so maintaining the same amount of agglomerant material. They are appraised amount of 5%, 8%, 10%, 12% and 15% of active silica in relation to Portland cement mass. The results suggest that for the appraised silicas there is little efficiency. Other aspects related to the mixtures just with addictive water reducers are commented with the purpose of also providing a high performance concrete. (author)

Synthesis of a nano-crystalline solid acid catalyst from fly ash and its catalytic performance

Energy Technology Data Exchange (ETDEWEB)

Chitralekha Khatri; Ashu Rani [Government P.G. College, Kota (India). Environmental Chemistry Laboratory

2008-10-15

The synthesis of nano-crystalline activated fly ash catalyst (AFAC) with crystallite size of 12 nm was carried out by chemical and thermal treatment of fly ash, a waste material generated from coal-burning power plants. Fly ash was chemically activated using sulfuric acid followed by thermal activation at 600{sup o}C. The variation of surface and physico-chemical properties of the fly ash by activation methods resulted in improved acidity and therefore, catalytic activity for acid catalyzed reactions. The AFAC was characterized by X-ray diffraction, FT-IR spectroscopy, N{sub 2}-adsorption-desorption isotherm, scanning electron microscopy, flame atomic absorption spectrophotometry and sulfur content by CHNS/O elemental analysis. It showed amorphous nature due to high silica content (81%) and possessed high BET surface area (120 m{sup 2}/g). The catalyst was found to be highly active solid acid catalyst for liquid phase esterification of salicylic acid with acetic anhydride and methanol giving acetylsalicylic acid and methyl salicylate respectively. A maximum yield of 97% with high purity of acetylsalicylic acid (aspirin) and a very high conversion 87% of salicylic acid to methyl salicylate (oil of wintergreen) was obtained with AFAC. The surface acidity and therefore, catalytic activity in AFAC was originated by increased silica content, hydroxyl content and higher surface area as compared to fly ash. The study shows that coal generated fly ash can be converted into potential solid acid catalyst for acid catalyzed reactions. Furthermore, this catalyst may replace conventional environmentally hazardous homogeneous liquid acids making an ecofriendly; solvent free, atom efficient, solid acid based catalytic process. 27 refs., 5 figs., 2 tabs.

AN EXPERIMENTAL STUDY ON STRENGTH AND PERMEABILITY PROPERTIES OF HIGH STRENGTH CONCRETE

OpenAIRE

Yedla Venkatesh * & G. Kalyan

2017-01-01

Concrete is the most important engineering material and the addition of some other materials may change the properties of concrete. Mineral additions which are also known as mineral admixtures have been used with cements for many years. There are two types of materials crystalline and non crystalline. High performance concrete (HPC) exceeds the properties and constructability of normal concrete. Micro silica or silica fume is very fine non crystalline material. Silica fume is produced in elec...

A study on the practicability of highly containing fly ash and silica fume cement

International Nuclear Information System (INIS)

Owada, Hitoshi; Mihara, Morihiro; Iriya, Keishiro; Matsui, Jun

2000-01-01

Cementitious materials have been planed to be used for the geological disposal of high-level radioactive waste and TRU waste. Degrading of host rock and buffer material induced by high pH leachate, however, is pointed out as one of technical issues. The authors have been developing a low alkalinity cement (the pH of the leachate of this cement is about 11) as an enhanced material to reduce the effect of the high pH problem. In this study, the applicability of low alkalinity cement developed to solve this problem was evaluated. The fluidity of the mortar was sufficient to fill the aperture in a structure filled with coarse aggregate. The concrete using the low alkalinity cement was also enough to fill a structure with the reinforcing steel. The compressive strength of a test-piece produced by the JIS method and of a core collected from the trial structure were over 60 MPa. These evaluation results show that developed low alkalinity cement had higher performances in mechanical properties and execution characteristics than JIS ordinary Portland cement. (author)

Study on Type C Coal Fly ash as an Additive to Molding Sand for Steel Casting

Science.gov (United States)

Palaniappan, Jayanthi

2017-04-01

Study of physio-chemical properties studies such as granulometric analysis, moisture, X ray fluorescence etc. were performed with Type C coal—combustion fly ash to investigate their potential as a distinct option for molding sand in foundry, thereby reducing the dependency on latter. Technological properties study such as compressive strength, tensile strength, permeability and compaction of various compositions of fly ash molding sand (10, 20 and 30 % fly ash substitute to chemically bonded sand) were performed and compared with silica molding sand. Steel casting production using this fly ash molding sand was done and the casting surface finish and typical casting parameters were assessed. It was noted that a good quality steel casting could be produced using type C fly ash molding sand, which effectively replaced 20 % of traditional molding sand and binders thereby providing greater financial profits to the foundry and an effective way of fly ash utilization (waste management).

Characterization of Tungsten Inert Gas (TIG) Welding Fume Generated by Apprentice Welders

Science.gov (United States)

Graczyk, Halshka; Lewinski, Nastassja; Zhao, Jiayuan; Concha-Lozano, Nicolas; Riediker, Michael

2016-01-01

Tungsten inert gas welding (TIG) represents one of the most widely used metal joining processes in industry. Its propensity to generate a greater portion of welding fume particles at the nanoscale poses a potential occupational health hazard for workers. However, current literature lacks comprehensive characterization of TIG welding fume particles. Even less is known about welding fumes generated by welding apprentices with little experience in welding. We characterized TIG welding fume generated by apprentice welders (N = 20) in a ventilated exposure cabin. Exposure assessment was conducted for each apprentice welder at the breathing zone (BZ) inside of the welding helmet and at a near-field (NF) location, 60cm away from the welding task. We characterized particulate matter (PM4), particle number concentration and particle size, particle morphology, chemical composition, reactive oxygen species (ROS) production potential, and gaseous components. The mean particle number concentration at the BZ was 1.69E+06 particles cm−3, with a mean geometric mean diameter of 45nm. On average across all subjects, 92% of the particle counts at the BZ were below 100nm. We observed elevated concentrations of tungsten, which was most likely due to electrode consumption. Mean ROS production potential of TIG welding fumes at the BZ exceeded average concentrations previously found in traffic-polluted air. Furthermore, ROS production potential was significantly higher for apprentices that burned their metal during their welding task. We recommend that future exposure assessments take into consideration welding performance as a potential exposure modifier for apprentice welders or welders with minimal training. PMID:26464505

Performance of laboratories analysing welding fume on filter samples: results from the WASP proficiency testing scheme.

Science.gov (United States)

Stacey, Peter; Butler, Owen

2008-06-01

This paper emphasizes the need for occupational hygiene professionals to require evidence of the quality of welding fume data from analytical laboratories. The measurement of metals in welding fume using atomic spectrometric techniques is a complex analysis often requiring specialist digestion procedures. The results from a trial programme testing the proficiency of laboratories in the Workplace Analysis Scheme for Proficiency (WASP) to measure potentially harmful metals in several different types of welding fume showed that most laboratories underestimated the mass of analyte on the filters. The average recovery was 70-80% of the target value and >20% of reported recoveries for some of the more difficult welding fume matrices were welding fume trial filter samples. Consistent rather than erratic error predominated, suggesting that the main analytical factor contributing to the differences between the target values and results was the effectiveness of the sample preparation procedures used by participating laboratories. It is concluded that, with practice and regular participation in WASP, performance can improve over time.

Effect of gasoline fumes on reproductive function in male albino rats.

Science.gov (United States)

Owagboriaye, Folarin O; Dedeke, Gabriel A; Ashidi, Joseph S; Aladesida, Adeyinka A; Olooto, Wasiu E

2018-02-01

The increase in the frequency of exposure to gasoline fumes and the growing incidence of infertility among humans has been a major concern and subject of discussion over the years in Nigeria. We therefore present the reproductive effect of gasoline fumes on inhalation exposure in 40 male albino rats. The rats were randomized into five experimental treatments (T) with eight rats per treatment. T1 (control) was exposed to distilled water while T2, T3, T4, and T5 were exposed to gasoline fumes in exposure chambers for 1, 3, 5, and 9 h daily respectively for 12 weeks. Serum level of testosterone, follicle stimulating hormone (FSH), luteinizing hormone (LH), prolactin, oxidative stress markers in the testicular tissue, epididymal sperm health assessment, and testicular histopathology of the rats were used as a diagnostic marker of reproductive dysfunction. Significant (p percentage motility in the exposed rats were observed. Significant (p < 0.05) increased in abnormal sperm cells characterized by damaged head, bent tail, damaged tail, and without head were also observed in the exposed rats. Histopathologically, severe degenerative testicular architectural lesions characterized by alterations in all the generations of sperm cells and reduction of interstitial cells were seen in the exposed rats. Gasoline fume is thus said to interfere with spermatogenesis and impair fertility in male gonad.

Characteristics of PAHs from deep-frying and frying cooking fumes.

Science.gov (United States)

Yao, Zhiliang; Li, Jing; Wu, Bobo; Hao, Xuewei; Yin, Yong; Jiang, Xi

2015-10-01

Cooking fumes are an important indoor source of polycyclic aromatic hydrocarbons (PAHs). Because indoor pollution has a more substantial impact on human health than outdoor pollution, PAHs from cooking fumes have drawn considerable attention. In this study, 16 PAHs emitted through deep-frying and frying methods using rapeseed, soybean, peanut, and olive oil were examined under a laboratory fume hood. Controlled experiments were conducted to collect gas- and particulate-phase PAHs emitted from the cooking oil fumes, and PAH concentrations were quantified via high-performance liquid chromatography (HPLC). The results show that deep-frying methods generate more PAHs and benzo[a]pyrene (B[a]P) (1.3 and 10.9 times, respectively) because they consume greater volumes of edible oil and involve higher oil temperatures relative to those of frying methods. In addition, the total B[a]Peq concentration of deep-frying is 2.2-fold larger than that of frying. Regarding the four types of edible oils studied, rapeseed oil produced more PAH emission than the other three oil varieties. For all of the cooking tests, three- and four-ringed PAHs were the main PAH components regardless of the food and oil used. Concerning the PAH partition between gas and particulate phase, the gaseous compounds accounted for 59-96 % of the total. Meanwhile, the particulate fraction was richer of high molecular weight PAHs (five-six rings). Deep-frying and frying were confirmed as important sources of PAH pollution in internal environments. The results of this study provide additional insights into the polluting features of PAHs produced via cooking activities in indoor environments.

A study of the bio-accessibility of welding fumes.

Science.gov (United States)

Berlinger, Balázs; Ellingsen, Dag G; Náray, Miklós; Záray, Gyula; Thomassen, Yngvar

2008-12-01

The respiratory bio-accessibility of a substance is the fraction that is soluble in the respiratory environment and is available for absorption. In the case of respiratory exposure the amount of absorbed substance plays a main role in the biological effects. Extensive bio-accessibility studies have always been an essential requirement for a better understanding of the biological effects of different workplace aerosols, such as welding fumes. Fumes generated using three different welding techniques, manual metal arc (MMA) welding, metal inert gas (MIG) welding, and tungsten inert gas (TIG) welding were investigated in the present study. Each technique was used for stainless steel welding. Welding fumes were collected on PVC membrane filters in batches of 114 using a multiport air sampler. Three different fluids were applied for the solubility study: deionised water and two kinds of lung fluid simulants: lung epithelial lining fluid simulant (Gamble's solution) and artificial lung lining fluid simulant (Hatch's solution). In order to obtain sufficient data to study the tendencies in solubility change with time, seven different leaching periods were used (0.5, 1, 2, 4, 8, 16, 24 h), each of them with three replicates. The effect of dissolution temperature was also studied. The total amounts of selected metals in the three different welding fumes were determined after microwave-assisted digestion with the mixture of aqua regia and hydrofluoric acid. The most obvious observation yielded by the results is that the solubility of individual metals varies greatly depending on the welding technique, the composition of the leaching fluid and leaching time. This study shows that the most reasonable choice as a media for the bio-assessment of solubility might be Hatch's solution by a dissolution time of 24 h.

Rice husk ash as a source of silica in alkali-activated fly ash and granulated blast furnace slag systems

Directory of Open Access Journals (Sweden)

Mejía, J. M.

2013-09-01

Full Text Available This study assesses the viability of using an agro-industrial by-product, rice husk ash (RHA from a Colombian rice company’s combustion facility, as a total replacement for the commercial sodium silicate ordinarily used in alkaliactivated binders. Fly ash (FA, granulated blast furnace slag (GBFS and binary 50FA:50GBFS blended pastes were activated with a mix of sodium hydroxide and either sodium silicate or one of two types of RHA. The pastes were characterised for strength, mineralogy and microstructure. The findings showed that the agro-industrial by-product can be used to yield alkali-activated materials with 7-day mechanical strengths on the order of 42 MPa. The study confirmed that both amorphous silica and part of the crystalline silica present in RHA participate in the alkaline activation process, providing the alkalinity is suitably adjusted.Este estudio evalúa la viabilidad de utilizar un subproducto agroindustrial, la ceniza de cascarilla de arroz (RHA proveniente de un equipo combustor de una empresa Arrocera en Colombia, como reemplazo total de la sílice aportada por el silicato de sodio comercial en sistemas cementicios activados alcalinamente. Se prepararon pastas de ceniza volante (FA, de escoria de alto horno (GBFS y un sistema binario 50FA:50GBFS, que fueron activadas por una mezcla de silicato de sodio e hidróxido de sodio, y por dos tipos de RHA. Las mezclas se caracterizaron mecánica, mineralógica y microestructuralmente. Los resultados demuestran que es posible obtener materiales activados alcalinamente con resistencias mecánicas del orden de 42 MPa, a 7 días de curado, utilizando el subproducto agroindustrial. Este estudio corrobora que tanto la sílice amorfa como parte de la sílice cristalina presente en RHA tienen la posibilidad de participar en el proceso de activación alcalina, siempre y cuando las condiciones de alcalinidad estén adecuadamente ajustadas.

Characterization of Tungsten Inert Gas (TIG) Welding Fume Generated by Apprentice Welders.

Science.gov (United States)

Graczyk, Halshka; Lewinski, Nastassja; Zhao, Jiayuan; Concha-Lozano, Nicolas; Riediker, Michael

2016-03-01

Tungsten inert gas welding (TIG) represents one of the most widely used metal joining processes in industry. Its propensity to generate a greater portion of welding fume particles at the nanoscale poses a potential occupational health hazard for workers. However, current literature lacks comprehensive characterization of TIG welding fume particles. Even less is known about welding fumes generated by welding apprentices with little experience in welding. We characterized TIG welding fume generated by apprentice welders (N = 20) in a ventilated exposure cabin. Exposure assessment was conducted for each apprentice welder at the breathing zone (BZ) inside of the welding helmet and at a near-field (NF) location, 60cm away from the welding task. We characterized particulate matter (PM4), particle number concentration and particle size, particle morphology, chemical composition, reactive oxygen species (ROS) production potential, and gaseous components. The mean particle number concentration at the BZ was 1.69E+06 particles cm(-3), with a mean geometric mean diameter of 45nm. On average across all subjects, 92% of the particle counts at the BZ were below 100nm. We observed elevated concentrations of tungsten, which was most likely due to electrode consumption. Mean ROS production potential of TIG welding fumes at the BZ exceeded average concentrations previously found in traffic-polluted air. Furthermore, ROS production potential was significantly higher for apprentices that burned their metal during their welding task. We recommend that future exposure assessments take into consideration welding performance as a potential exposure modifier for apprentice welders or welders with minimal training. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Microarray-based analysis of the lung recovery process after stainless-steel welding fume exposure in Sprague-Dawley rats.

Science.gov (United States)

Oh, Jung-Hwa; Yang, Mi-jin; Yang, Young-Su; Park, Han-Jin; Heo, Sun Hee; Lee, Eun-Hee; Song, Chang-Woo; Yoon, Seokjoo

2009-02-01

Repeated exposure to welding fumes promotes a reversible increase in pulmonary disease risk, but the molecular mechanisms by which welding fumes induce lung injury and how the lung recovers from such insults are unclear. In the present study, pulmonary function and gene-expression profiles in the lung were analyzed by Affymetrix GeneChip microarray after 30 days of consecutive exposure to manual metal arc welding combined with stainless-steel (MMA-SS) welding fumes, and again after 30 days of recovery from MMA-SS fume exposure. In total, 577 genes were identified as being either up-regulated or down-regulated (over twofold changes, p process of the lung were up-regulated exclusively in the recovery group. Collectively, these data may help elucidate the molecular mechanism of the recovery process of the lung after welding fume exposure.

Development of low-pH cementitious materials for HLRW repositories

International Nuclear Information System (INIS)

Garcia Calvo, J.L.; Hidalgo, A.; Alonso, C.; Fernandez Luco, L.

2010-01-01

One of the most accepted engineering construction concepts of underground repositories for high radioactive waste considers the use of low-pH cementitious materials. This paper deals with the design of those based on Ordinary Portland Cements with high contents of silica fume and/or fly ashes that modify most of the concrete 'standard' properties, the pore fluid composition and the microstructure of the hydrated products. Their resistance to long-term groundwater aggression is also evaluated. The results show that the use of OPC cement binders with high silica content produces low-pH pore waters and the microstructure of these cement pastes is different from the conventional OPC ones, generating C-S-H gels with lower CaO/SiO 2 ratios that possibly bind alkali ions. Leaching tests show a good resistance of low-pH concretes against groundwater aggression although an altered front can be observed.

Fly ash as a sorbent for the removal of biologically resistant organic matter

Energy Technology Data Exchange (ETDEWEB)

Vandenbusch, M B; Sell, N J [Wisconsin Public Service Corporation, Green Bay, WI (USA)

1992-02-01

Six different fly ashes, in both an untreated and an acidified form, were studied with respect to their ability to remove colour and organic materials from a municipal waste treatment facility effluent. Colour, fluorescence, and chemical oxygen demand were used to monitor the removal. The apparent predominant mechanism varies with the pH and the chemical characteristics of the ash. These mechanisms include carbon sorption, calcium precipitation of tannins and humics, sorption on the fly ash surface by silica, alumina, and/or iron oxide and, in the acidified situation, coagulation of coloured colloids in the effluent dissolved from the fly ash. Some additional deleterious components are dissolved into the effluent during the treatment process. Many of these materials can, however, be removed by using a two-stage fly ash sorption process. Particularly of interest is the ability to remove over 90% of the boron from the effluent. 13 refs., 10 figs., 9 tabs.

Personal exposure to metal fume, NO2, and O3 among production welders and non-welders.

Science.gov (United States)

Schoonover, Todd; Conroy, Lorraine; Lacey, Steven; Plavka, Julie

2011-01-01

The objective of this study was to characterize personal exposures to welding-related metals and gases for production welders and non-welders in a large manufacturing facility. Welding fume metals and irritant gases nitrogen dioxide (NO(2)) and ozone (O(3)) were sampled for thirty-eight workers. Personal exposure air samples for welding fume metals were collected on 37 mm open face cassettes and nitrogen dioxide and ozone exposure samples were collected with diffusive passive samplers. Samples were analyzed for metals using Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and welding fume metal exposure concentrations were defined as the sum of welding-related metals mass per volume of air sampled. Welding fume metal exposures were highly variable among similar types of welding while NO(2) and O(3) exposure were less variable. Welding fume metal exposures were significantly higher 474 μg/m(3) for welders than non-welders 60 μg/m(3) (p=0.001). Welders were exposed to higher concentrations of NO(2) and O(3) than non-welders but the differences were not statistically significant. Welding fume metal exposure concentrations for welders performing gas metal arc welding (GMAW) and shielded metal arc welding (SMAW) were higher than welders performing gas tungsten arc welding (GTAW). Non-welders experienced exposures similar to GTAW welders despite a curtain wall barrier separating welding and non-welding work areas.

The development and site investigation of fume diluter

Energy Technology Data Exchange (ETDEWEB)

Kim, Bok Youn; Kang, Chang Hee; Jo, Young Do; Lim, Sang Taek [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

1996-12-01

It is third project year on `Application of mobile diesel equipment in underground mines` for providing appropriate measures to improve underground working environment contaminated by the diesel exhaust pollutants. For reducing the exhaust temperature bellow 70 deg. C to prevent production of the governing pollutant (NO{sub 2}), the fume diluter is verified the most effective device through the site investigation. Therefore, the fume diluter is strongly recommended instead of catalytic converter which is employed presently. The performances derived from the tests are as follows; 1) This device increased air flow to 6.7-8.4 times of the original exhaust, 2) Exhaust temperature can be reduced to 66 deg. C from 161 deg. C, 3) All the pollutants can be reduced to bellow than 30 % of exhaust concentration, 4) This device requires less cost and no maintenance. (author). 4 tabs., 4 figs.

Effects of Exposure to Welding Fume on Lung Function: Results from the German WELDOX Study.

Science.gov (United States)

Lehnert, M; Hoffmeyer, F; Gawrych, K; Lotz, A; Heinze, E; Berresheim, H; Merget, R; Harth, V; Van Gelder, R; Hahn, J-U; Hartwig, A; Weiß, T; Pesch, B; Brüning, T

2015-01-01

The association between exposure to welding fume and chronic obstructive pulmonary disease (COPD) has been insufficiently clarified. In this study we assessed the influence of exposure to welding fume on lung function parameters. We investigated forced expiratory volume in 1 s (FEV1), forced vital capacity (FVC), FEV1/FVC, and expiratory flow rates in 219 welders. We measured current exposure to respirable particles and estimated a worker's lifetime exposure considering welding techniques, working conditions and protective measures at current and former workplaces. Multiple regression models were applied to estimate the influence of exposure to welding fume, age, and smoking on lung function. We additionally investigated the duration of working as a welder and the predominant welding technique. The findings were that age- and smoking-adjusted lung function parameters showed no decline with increasing duration, current exposure level, and lifetime exposure to welding fume. However, 15% of the welders had FEV1/FVC below the lower limit of normal, but we could not substantiate the presence of an association with the measures of exposure. Adverse effects of cigarette smoking were confirmed. In conclusion, the study did not support the notion of a possible detrimental effect of exposure to welding fume on lung function in welders.

Green options for anti-corrosion of high strength concrete incorporating ternary pozzolan materials

Directory of Open Access Journals (Sweden)

Chen Yuan-Yuan

2017-01-01

Full Text Available This paper applied the densified mixture design algorithm(DMDA method by incorporating ternary pozzolans (fly ash, slag and silica fume; mix I and mix II to design high strength concrete (HSC mixtures with w/cm ratios from 0.24 to 0.30. Concrete without pozzolans was used as a control group (mix III, w/c from 0.24 to 0.30, and silica fume (5% was added as a substitute for part of the cement and set as mix IV. Experiments performed compressive strength, four-point resistance meter to measure the conductivity, and rapid chloride ion penetrability tests (ASTM C1202 were assessed the anti-corrosion. The life cycle inventory of LEED suggested by the PCA indicated the green options for cementitious materials. Results showed that mix I and II indicated cement used, CO2 reduction, raw materials and energy consumption all decreased more 50% than mix III, and mix IV was 5% less. The compressive strength and anti-corrosion levels showed that mix I and II were better than mix III and IV, and with ternary pozzolans could enhance the long-term durability (92 days due to a resistivity greater 20 KΩ-cm and a charge passed lower than 2000 Coulombs. HSC with an appropriate design could reduce the carbon footprint and improve the durability.

Exposure to Cooking Fumes and Acute Reversible Decrement in Lung Functional Capacity

Directory of Open Access Journals (Sweden)

Masoud Neghab

2017-10-01

Full Text Available Background: Being exposed to cooking fumes, kitchen workers are occupationally at risk of multiple respiratory hazards. No conclusive evidence exists as to whether occupational exposure to these fumes is associated with acute and chronic pulmonary effects and symptoms of respiratory diseases. Objective: To quantify the exposure levels and evaluate possible chronic and acute pulmonary effects associated with exposure to cooking fumes. Methods: In this cross-sectional study, 60 kitchen workers exposed to cooking fumes and 60 unexposed employees were investigated. The prevalence of respiratory symptoms among these groups was determined through completion of a standard questionnaire. Pulmonary function parameters were also measured before and after participants' work shift. Moreover, air samples were collected and analyzed to quantify their aldehyde, particle, and volatile organic contents. Results: The mean airborne concentrations of formaldehyde, acetaldehyde, and acrolein was 0.45 (SD 0.41, 0.13 (0.1, and 1.56 (0.41 mg/m3, respectively. The mean atmospheric concentrations of PM1, PM2.5, PM7, PM10, and total volatile organic compounds (TVOCs was 3.31 (2.6, 12.21 (5.9, 44.16 (16.6, 57 (21.55 μg/m3, and 1.31 (1.11 mg/m3, respectively. All respiratory symptoms were significantly (p<0.05 more prevalent in exposed group. No significant difference was noted between the pre-shift mean of spirometry parameters of exposed and unexposed group. However, exposed workers showed cross-shift decrease in most spirometry parameters, significantly lower than the pre-shift values and those of the comparison group. Conclusion: Exposure to cooking fumes is associated with a significant increase in the prevalence of respiratory symptoms as well as acute reversible decrease in lung functional capacity.

Effects on the efficiency of activated carbon on exposure to welding fumes

Energy Technology Data Exchange (ETDEWEB)

Ghosh, D. [Southern Company Services, Inc., Birmingham, AL (United States)

1995-02-01

It is the intention of this paper to document that certain types of welding fumes have little or no effect on the effectiveness of the carbon filter air filtration efficiency when directly exposed to a controlled amount of welding fumes for a short-term period. The welding processes studied were restricted to shielded metal arc welding (SMAW), flux cored arc welding (FCAW), gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) processes. Contrary to the SMAW and FCAW processes, the GTAW (or TIG) and the GMAW (or MIG) welding processes do not require the use of flux as part of the overall process. Credit was taken for these processes occurring in inert gas environments and producing minimal amount of smoke. It was concluded that a study involving the SMAW process would also envelop the effects of the TIG and MIG welding processes. The quantity of welding fumes generated during the arc welding process is a function of the particular process, the size and type of electrode, welding machine amperage, and operator proficiency. For this study, the amount of welding for specific testing was equated to the amount of welding normally conducted during plant unit outages. Different welding electrodes were also evaluated, and the subsequent testing was limited to an E7018 electrode which was judged to be representative of all carbon and stainless steel electrodes commonly used at the site. The effect of welding fumes on activated charcoal was tested using a filtration unit complete with prefilters, upstream and downstream high efficiency particulate air (HEPA) filters, and a carbon adsorber section. The complete system was field tested in accordance with ANSI N510 standards prior to exposing the filters and the adsorber bed to welding fumes. The carbon samples were tested at an established laboratory using ASTM D3803-1989 standards.

Bronchiolitis from nitrous fumes

Energy Technology Data Exchange (ETDEWEB)

Darke, C S; Warrack, A J.N.

1958-01-01

Gases of low solubility (e.g., NO/sub 2/) may not irritate upper respiratory tract but may act insidiously on lower tract producing edema and bronchiolitis. Cases of bronchiolitis (1 resulting in death) from exposure to brown nitrous fumes are reported. There were no or slight symptoms at first but severe ones after about 1 wk. Pathology appears as acute pulmonary edema with damage and desquamation of alveolar epithelium particularly and that of respiratory bronchioles somewhat. Patchy atelectasis, bronchopneumonia and disruption of fibers in cell walls may also occur. Severe cases have obliteration of lumen (bronchiolitis obliterans) with extreme distress and death.

Designer silica layers for advanced applications: Processing and properties

Science.gov (United States)

Anderson, Adam

, including glasses, metals, fibers, polymers, and plastics. This process has the potential to enable common organosilicon-based chemistries on polymer surfaces, but before the potential impact of this technology can be realized, the fundamental groundwork must be laid. In this work, a series of investigations into the properties of the vapor deposited silica layer are conducted. It is determined that the morphology of the silica layer depends strongly on the relative pressures of the precursor gases. Furthermore, the vapor deposited silica layer has many commonalities with conventionally prepared silica materials (fumed or precipitated) and does support the formation of self-assembled monolayers for organosilicon-based precursors. However, there are also some differences in chemical reactivity of surface groups on the vapor deposited silica layer relative to the surface of conventionally prepared silica materials, which contribute to different chemical behavior in some circumstances. Also, the deposition of the silica layers under study here is confirmed on several model polymeric substrates by ATR-FTIR and atomic force microscopy.

Use of Fly Ash in the Mitigation of Alkali-Silica Reaction in Concrete

Science.gov (United States)

2010-11-12

crystallinity of the silica and its solubility. Common reactive minerals susceptible to ASR include strained quartz, cristobalite, opal, obsidian , chert, and... obsidian .[5] Adequate Moisture Adequate moisture, the third and final necessary component for ASR to occur, is one of the key components in the

Persistence of Change: Fume Hood Campaign Lessons

Science.gov (United States)

Feder, Elah; Robinson, Jennifer; Wakefield, Sarah

2012-01-01

Purpose: Sustainability initiatives typically operate for a limited time period, but it is often unclear whether they have lasting effects. The purpose of this paper is to examine a laboratory fume hood campaign, in order to identify factors that might contribute or detract from long-term change persistence. Design/methodology/approach: The…

Welding fumes from stainless steel gas metal arc processes contain multiple manganese chemical species.

Science.gov (United States)

Keane, Michael; Stone, Samuel; Chen, Bean

2010-05-01

Fumes from a group of gas metal arc welding (GMAW) processes used on stainless steel were generated using three different metal transfer modes and four different shield gases. The objective was to identify and measure manganese (Mn) species in the fumes, and identify processes that are minimal generators of Mn species. The robotic welding system was operated in short-circuit (SC) mode (Ar/CO2 and He/Ar), axial spray (AXS) mode (Ar/O2 and Ar/CO2), and pulsed axial-spray (PAXS) mode (Ar/O2). The fumes were analyzed for Mn by a sequential extraction process followed by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) analysis, and by X-ray diffraction (XRD). Total elemental Mn, iron (Fe), chromium (Cr) and nickel (Ni) were separately measured after aqua regia digestion and ICP-AES analysis. Soluble Mn2+, Fe2+, Fe3+, and Ni2+ in a simple biological buffer (phosphate-buffered saline) were determined at pH 7.2 and 5.0 after 2 h incubation at 37 C by ion chromatography. Results indicate that Mn was present in soluble form, acid-soluble form, and acid-soluble form after reduction by hydroxylamine, which represents soluble Mn0 and Mn2+ compounds, other Mn2+ compounds, and (Mn3+ and Mn4+) compounds, respectively. The dominant fraction was the acid-soluble Mn2+ fraction, but results varied with the process and shield gas. Soluble Mn mass percent in the fume ranged from 0.2 to 0.9%, acid-soluble Mn2+ compounds ranged from 2.6 to 9.3%, and acid plus reducing agent-soluble (Mn3+ and Mn4+) compounds ranged from 0.6 to 5.1%. Total Mn composition ranged from 7 to 15%. XRD results showed fumes had a crystalline content of 90-99% Fe3O4, and showed evidence of multiple Mn oxides, but overlaps and weak signals limited identification. Small amounts of the Mn2+ in the fume (welding process. Mn generation rates for the fractions were tabulated, and the influence of ozone is discussed. The conclusions are that exposures to welding fumes include multiple Mn species, both

Detailed characterization of welding fumes in personal exposure samples

International Nuclear Information System (INIS)

Quémerais, B; Mino, James; Amin, M R; Golshahi, H; Izadi, H

2015-01-01

The objective of the project was to develop a method allowing for detailed characterization of welding particles including particle number concentration, size distribution, surface chemistry and chemical composition of individual particles, as well as metal concentration of various welding fumes in personal exposure samples using regular sampling equipment. A sample strategy was developed to evaluate the variation of the collection methods on mass concentration. Samples were collected with various samplers and filters at two different locations using our collection system. The first location was using a robotic welding system while the second was manual welding. Collected samples were analysed for mass concentration using gravimetryand metal concentration using ICP/OES. More advanced analysis was performed on selected filters using X-Ray Photoelectron Spectroscopy to determine surface composition of the particles, and X-Ray Diffraction to determine chemical composition of the fumes. Results showed that the robotic system had a lot of variation in space when the collection system was located close to the weld. Collection efficiency was found to be quite variable depending upon the type of filter. As well, metal concentrations in blank filters were dependent upon the type of filter with MCE presenting with the highest blank values. Results obtained with the XRD and XPS systems showed that it was possible to analyse a small of powdered welding fume sample but results on filters were not conclusive. (paper)

Development of Magnesium Silicate Hydrate cement system for nuclear waste encapsulation

International Nuclear Information System (INIS)

Zhang, T.; Vandeperre, L.J.; Cheeseman, C.R.

2012-01-01

A novel low pH cement system for encapsulating nuclear industry wastes containing aluminium has been developed using blends of MgO and silica fume (SF). Identification of the hydrated phases in MgO/silica fume samples showed that brucite formed in early stages of hydration and then reacted with the silica fume to produce a magnesium silicate hydrate (M-S-H) gel phase. When all brucite reacts with silica fume a cement system with an equilibrium pH just below 10 was achieved. Selected mixes have been characterized for hydration reactions, setting time and strength development. Mortar samples with w/s ratios of 0.5 and 50% by weight of sand added achieved compressive strengths in excess of 95 MPa after 28 days. The addition of MgCO 3 buffered the early pH and the addition of fine sand particles eliminated shrinkage cracking. The interaction of the optimised mortar with Al metal has been investigated. Al metal strips were firmly bound into the MgO:SF:sand samples and no H 2 gas detected, and this indicates that the novel systems developed in this work have potential for encapsulating certain types of problematic legacy wastes from the nuclear industry. (authors)

Chloride ingress prediction

DEFF Research Database (Denmark)

Frederiksen, Jens Mejer; Geiker, Mette Rica

2008-01-01

Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...... of depth and time, when both the surface chloride concentration and the diffusion coefficient are allowed to vary in time. The model is presented in a companion paper....

High performance concrete with blended cement

International Nuclear Information System (INIS)

Biswas, P.P.; Saraswati, S.; Basu, P.C.

2012-01-01

Principal objectives of the proposed project are two folds. Firstly, to develop the HPC mix suitable to NPP structures with blended cement, and secondly to study its durability necessary for desired long-term performance. Three grades of concrete to b considered in the proposed projects are M35, M50 and M60 with two types of blended cements, i.e. Portland slag cement (PSC) and Portland pozzolana cement (PPC). Three types of mineral admixtures - silica fume, fly ash and ground granulated blast furnace slag will be used. Concrete mixes with OPc and without any mineral admixture will be considered as reference case. Durability study of these mixes will be carried out

Work-principle model for predicting toxic fumes of nonideal explosives

Energy Technology Data Exchange (ETDEWEB)

Wieland, Michael S. [National Institute of Occupational Safety and Health, Pittsburgh Research Center, P.O. Box 18070, Pittsburgh, PA 15236-0070 (United States)

2004-08-01

The work-principle from thermodynamics was used to formulate a model for predicting toxic fumes from mining explosives in underground chamber tests, where rapid turbulent combustion within the surrounding air noticeably changes the resulting concentrations. Two model constants were required to help characterize the reaction zone undergoing rapid chemical transformations in conjunction with heat transfer and work output: a stoichiometry mixing fraction and a reaction-quenching temperature. Rudimentary theory with an unsteady uniform concentration gradient was taken to characterize the combustion zone, yielding 75% for the mixing fraction. Four quenching temperature trends were resolved and compared to test results of ammonium nitrate compositions with different fuel-oil percentages (ANFO). The quenching temperature 2345 K was the optimum choice for fitting the two major components of fume toxicity: carbon monoxide (CO) and total nitrogen oxides (NO{sub X}). The resulting two-constant model was used to generate comparisons for test results of ANFO compositions with additives. Though respectable fits were usually found, charge formulations which reacted weakly could not be resolved numerically. The work-principle model yields toxic concentrations for a range of charge formulations, making it a useful tool for investigating the potential hazard of released fumes and reducing the risk of unwanted incidents. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

Silis Dumanının Betonda Mekanik Çatlak Oluşumlarına Etkisi

OpenAIRE

TOPÇU, İlker Bekir; CANBAZ, Mehmet

2017-01-01

High strength concrete are obtained by adding the silica fume, which is anElectrometallurgy Facility’s, into concrete production. In this study, increasing on strength andmechanic crack formations of concrete, which were produced by CEM II/A-M 32.5 cement,using silica fume and superplasticizer, were investigated in the respect of microstructure. Photoof microstructure has been taken and chemical analysis has been determined by using ElectronMicroscope. As a result of studies, investigated mic...

Local exhaust ventilation for the control of welding fumes in the construction industry--a literature review.

Science.gov (United States)

Flynn, Michael R; Susi, Pam

2012-08-01

Arc welding is a common unit operation in the construction industry, where frequent changes in location and welding position make it more difficult to control fume exposures than in industries where fixed locations are the norm. Welders may be exposed to a variety of toxic airborne contaminants including manganese (Mn) and hexavalent chromium (CrVI). Local exhaust ventilation (LEV) is a well-known engineering control for welding fumes but has not been adopted widely in the construction industry. This literature review presents data on the performance of a variety of LEV systems for welding fume control from the construction (five references), shipyard (five references), and other industries. The studies indicate that LEV can reduce fume exposures to total particulate, Mn, and CrVI to levels below currently relevant standards. Field studies suggest that 40-50% or more reduction in exposure is possible with portable or fixed LEV systems relative to natural ventilation but that correct positioning of the hood and adequate exhaust flow rates are essential. Successful implementation of extraction guns for gas metal arc welding (GMAW) and flux core arc welding has been demonstrated, indicating that a successful balance between extraction airflow and shielding gas requirements is possible. Work practices are an important part of achieving successful control of fume exposures; in particular, positioning the hood close to the arc, checking exhaust flow rates, and avoiding the plume. Further research is needed on hood size effects for controlling welding fume with portable LEV systems and identifying and overcoming barriers to LEV use in construction.

Removal of Copper (II Ions in Aqueous Solutions by Sorption onto Alkali Activated Fly Ash

Directory of Open Access Journals (Sweden)

Darmayanti Lita

2018-01-01

Full Text Available Fly ash is a particulate material produced from coal combustion power plants with major components are silica, alumina, iron oxide, calcium oxide, magnesium oxide, and carbon which are ideal for metal adsorbents. The potential use of fly ash in the wastewater treatment process is obvious because it can be obtained cheaply in large quatities and it can be used as an adsorbent. However, fly ash still shows lower adsorption capacity unless it is activated. In this study, fly ash activated by NaOH 14 M and KOH 14 M solutions. The batch experiments were carried out to study the sorption of copper ions from aqueous on alkali activated fly ash. The influence of initial concentration and contact time were examined at constant pH and dose of adsorbent. The sorption capacity of copper ions increased with the initial concentration and contact time. The sorption capacities followed the order Na1>Ka1>FA. The adsorption isotherm model exhibited that the Langmuir model is very suitable with copper ions adsorption onto fly ash and alkali activated fly ash. Kinetic study shows that adsorption of copper ions onto FA, Na1, and Ka1 follows the pseudo second-order kinetics.

30 CFR 71.700 - Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors.

Science.gov (United States)

2010-07-01

... gases, dust, fumes, mists, and vapors. 71.700 Section 71.700 Mineral Resources MINE SAFETY AND HEALTH... limit values for gases, dust, fumes, mists, and vapors. (a) No operator of an underground coal mine and... limit values adopted by the American Conference of Governmental Industrial Hygienists in “Threshold...

After-blast fumes from ANFO mixtures - the effect of prill type and mixing techniques

Energy Technology Data Exchange (ETDEWEB)

Farnfield, R.; Wetherelt, A.

2003-06-01

Over the last couple of years the Technical Services Department of exchem explosives has received a number of enquiries regarding the nature of after-blast fumes. These enquiries have been driven by two concerns: site-related health and safety and public comment from people living close to blasting operations. The paper examines how these choices can impact the quality and quantity of after-blast fume. 3 refs., 9 figs., 3 tabs.

Calculation of calcium diffusion coefficient of cement hardenings using minute pore data

International Nuclear Information System (INIS)

Hitomi, Takashi; Takeda, Nobufumi; Iriya, Keishiro

2009-01-01

This report describes the calculations of the diffusion coefficient of the Ca ion of cement hardenings using minute pore data. The observed hardenings were ordinary Portland cement (OPC), low-heat Portland cement with fly ash (LPC+FA) and highly fly ash containing silica fume cement (HFSC). The samples were cured in the standard and artificially leached by accelerated test. Minute pore datas of the cement hardenings were acquired with image processing of internal structural information obtained from high resolution X-ray computed tomography observations. Upon analysis, several voxels are combined into one bigger voxel, the diffusion coefficient of the voxels were determined in proportion to the number of voxels which were included in. The results reveal that the change in the calcium diffusion coefficient of OPC due to leaching was large, but the LPC+FA and HFSC cements exhibited even greater changes than OPC. It is suggested that the diffusion coefficients are proportional to the Ca/Si ratio of the samples. (author)

Late-Age Properties of Concrete with Different Binders Cured under 45°C at Early Ages

Directory of Open Access Journals (Sweden)

Hu Jin

2017-01-01

Full Text Available It is commonly accepted that high curing temperature (near 60°C or above results in reduced mechanical properties and durability of concrete compared to normal curing temperature. The internal temperature of concrete structures at early ages is not so high as 60°C in many circumstances. In this paper, concretes were cured at 45°C at early ages and their late-age properties were studied. The concrete cured at 20°C was employed as the reference sample. Four different concretes were used: plain cement concrete, concrete containing fly ash, concrete containing ground granulate blast furnace slag (GGBS, and concrete containing silica fume. The results show that, for each concrete, high-temperature curing after precuring does not have any adverse effect on the nonevaporable water content, compressive strength, permeability to chloride ions, and the connected porosity of concrete at late ages compared with standard curing. Additionally, high-temperature curing improves the late-age properties of concrete containing fly ash and GGBS.

Effect of Generator (Exhaust) Fumes on the Growth and ...

African Journals Online (AJOL)

PROF HORSFALL

as the distance of the plants from the source of pollution increased, only the 3 m treatment led to significant ... plants were adversely affected by the fume emission especially at the distance of 3 m away from the ..... Principles of Biochemical.

Small angle neutron scattering from hydrated cement pastes

International Nuclear Information System (INIS)

Sabine, T.M.; Bertram, W.K.; Aldridge, L.P.

1996-01-01

Small angle neutron scattering (SANS) was used to study the microstructure of hydrating cement made with, and without silica fume. Some significant differences were found between the SANS spectra of pastes made from OPC (ordinary Portland cement) and DSP (made with silica fume and superplasticiser). The SANS spectra are interpreted in terms of scattering from simple particles. Particle growth was monitored during hydration and it was found that the growth correlated with the heat of hydration of the cement

Effect of Fibers and Filler Types on Fresh and Hardened Properties of Self-Compacting Concrete

Directory of Open Access Journals (Sweden)

Saeed K. Rejeb* , Majid Kh . N. Ayad A. M.

2014-04-01

Full Text Available This paper deals with studying the fresh and hardened properties of self-compacting concrete, by using three types of filler (silica fume, clinker powder & lime stone powder, and two types of fibers (steel & glass fibers with volume fractions of (0.5% and (0.1% respectively. For each type of fillers, the fresh properties are measured by using Slump test, J- ring and V- funnel, while hardened properties include the compressive strength, splitting tensile strength and flexural strength. The results show that adding fibers to the self-compacting concrete (SCC well reduces the workability and improves the hardened properties. Also, the study concluded that better workability is obtained by using (lime stone, silica fume and clinker powder as fillers, respectively. While the higher hardened properties are gained by using silica fume were rather than those of other types of fillers 

Study on construction method of concrete in the underground research laboratory. 3

International Nuclear Information System (INIS)

Iriya, Keishiro; Mikami, Tetsuji; Takeda, Nobufumi; Akiyoshi, Kenji

2003-02-01

The Horonobe underground research laboratory project doesn't carry on only safety assessment study but also demonstration of construction technique upon nuclear waste repositories. Low alkalinity cement is one of candidates for engineered barrier in order to prevent alteration of bentonite and rock by hyper alkaline solution. JNC has developed low alkalinity cement (HFSC) which contains a lot of fly ash, and has studied the physical and chemical properties by laboratory test. Effect on variety of quality of fly ash and monitoring corrosion of rebars in off-shore condition has been studied. In-situ test for actual use of HFSC in constructing the facility was planned. The results are summarized as below. Effects of variety of flay ash upon lower pH are relatively small by testing two type of fly ash and several fly as content. Variety of fly ash effects properties of fresh concrete but its effect is not significant. And it little effects on mechanical behavior. However, it doesn't effect on properties of shotcrete. Although rebars corrode in HFSC in spite of no intrusion of chloride, increment of corrosion is not significant in half an year until an year. Applicability for structural members is demonstrated by loading test of tunnel concrete segments of HFSC. Pre-mixed HFSC can be supplied by mixing fly ash and silica fume in Sapporo and carry to Horonobe by cement truck. (author)

Alterations in cardiomyocyte function after pulmonary treatment with stainless steel welding fume in rats.

Science.gov (United States)

Popstojanov, Risto; Antonini, James M; Salmen, Rebecca; Ye, Morgan; Zheng, Wen; Castranova, Vincent; Fekedulegn, Desta B; Kan, Hong

2014-01-01

Welding fume is composed of a complex of different metal particulates. Pulmonary exposure to different welding fumes may exert a negative impact on cardiac function, although the underlying mechanisms remain unclear. To explore the effect of welding fumes on cardiac function, Sprague-Dawley rats were exposed by intratracheal instillation to 2 mg/rat of manual metal arc hard surfacing welding fume (MMA-HS) once per week for 7 wk. Control rats received saline. Cardiomyocytes were isolated enzymatically at d 1 and 7 postexposure. Intracellular calcium ([Ca(2+)]i) transients (fluorescence ratio) were measured on the stage of an inverted phase-contrast microscope using a myocyte calcium imaging/cell length system. Phosphorylation levels of cardiac troponin I (cTnI) were determined by Western blot. The levels of nonspecific inflammatory marker C-reactive protein (CRP) and proinflammatory cytokine interleukin-6 (IL-6) in serum were measured by enzyme-linked immunosorbent assay (ELISA). Contraction of isolated cardiomyocytes was significantly reduced at d 1 and d 7 postexposure. Intracellular calcium levels were decreased in response to extracellular calcium stimulation at d 7 postexposure. Changes of intracellular calcium levels after isoprenaline hydrochloride (ISO) stimulation were not markedly different between groups at either time point. Phosphorylation levels of cTnI in the left ventricle were significantly lower at d 1 postexposure. The serum levels of CRP were not markedly different between groups at either time point. Serum levels of IL-6 were not detectable in both groups. Cardiomyocyte alterations observed after welding fume treatment were mainly due to alterations in intracellular calcium handling and phosphorylation levels of cTnI.

The Study Of Histopathological Effects Of Welding Fumes On Spermatogenesis In Rat

Directory of Open Access Journals (Sweden)

Arab M R

2005-07-01

Full Text Available Background: Fumes generated during electric welding are one of air pollutants of working place in industrial companies, which can cause some clinical signs and diseases in worker, including mucosal irritation, changing of semen quality and cancer. Chronic exposure of workers with these fumes can cause reduce sperm motility and forward penetration and decrease in normal sperm count. Although a lot of researches were done in this field up to now, there is little information about histopathological effects of these fumes on germinal epithelium. The aim of this study was to identify structural changes of germinal epithelium in Rat as an experimental model after exposure to fumes of electric welding in exposure chamber. Material and Methods: A total number of 60 Sprague Dawley Rats were chosen and divided into experimental (40 and control (20 groups. Each of groups was subdivided into 2, 4, 6 and 8-week subgroups. The number of Rat in each subgroup of experimental and control group was 10 and 5 respectively. Animals were housed in standard situation. After adaptation experimental group were exposed to fumes of electric welding (AMA 2000 electrode, 100 Ampere, 0.1 cm/s speed of electrode welding for 2 hour/day and 5 day/week. The rate of air turn over in exposure chamber was fixed to 12-15/hour. The amount of O3, CO, CO2, NO + NO2 and particulate matter were measured by Galtec detectors and Cellulose acetate filter respectively. According to time table animals were killed and specimens from testis were taken and fixed in formaline buffer solution and processed routinely. Sections with 5-7 micrometer in thickness were stained by H-E, PAS, PNA and Alcian blue pH=2.5. The thickness of germinal epithelium was measured and data were analyzed by Kruskall Wallis test. Results: The results of this study showed a few quantitative and qualitative changes in germinal epithelium. Vasodilatation of vessels in tunica albuginea and interstitial tissue, decreasing of

Structural and Mechanical Characterization of Sustainable Composites Based on Recycled and Stabilized Fly Ash

Directory of Open Access Journals (Sweden)

Stefano Besco

2014-08-01

Full Text Available This paper reports the results on the use of an innovative inert, based on stabilized fly ash from municipal solid waste incineration as a filler for polypropylene. The starting material, which contains large quantities of leachable Pb and Zn, was stabilized by means of an innovative process using rice husk ash as a waste silica source, together with other fly ashes, such as coal fly ash and flue gas desulfurization residues. The use of all waste materials to obtain a new filler makes the proposed technology extremely sustainable and competitive. The new composites, obtained by using the stabilized material as a filler for polypropylene, were characterized and their mechanical properties were also investigated. A comparison with a traditional polypropylene and calcium carbonate based compound was also done. This research activity was realized in the frame of the COSMOS-RICE project, financed by the EU Commission.

Functionally graded Nylon-11/silica nanocomposites produced by selective laser sintering

International Nuclear Information System (INIS)

Chung, Haseung; Das, Suman

2008-01-01

Selective laser sintering (SLS), a layered manufacturing-based freeform fabrication approach was explored for constructing three-dimensional structures in functionally graded polymer nanocomposites. Here, we report on the processing and properties of functionally graded polymer nanocomposites of Nylon-11 filled with 0-10% by volume of 15 nm fumed silica nanoparticles. SLS processing parameters for the different compositions were developed by design of experiments (DOE). The densities and micro/nanostructures of the nanocomposites were examined by optical microscopy and transmission electron microscopy (TEM). The tensile and compressive properties for each composition were then tested. These properties exhibit a nonlinear variation as a function of filler volume fraction. Finally, two component designs exhibiting a one-dimensional polymer nanocomposite material gradient were fabricated. The results indicate that particulate-filled functionally graded polymer nanocomposites exhibiting a one-dimensional composition gradient can be successfully processed by SLS to produce three-dimensional components with spatially varying mechanical properties

Association between cooking oil fume exposure and lung cancer among Chinese nonsmoking women: a meta-analysis

Directory of Open Access Journals (Sweden)

Xue Y

2016-05-01

Full Text Available Yingbo Xue, Ying Jiang, Shan Jin, Yong Li Department of Oncology, Guizhou Provincial People’s Hospital, Guiyang, Guizhou, People’s Republic of China Abstract: Lung cancer has been the main cause of cancer death around the world. Cigarette smoking has been identified as a risk factor for lung cancer in males. However, the etiological factors in nonsmoking women remain elusive. A meta-analysis was conducted to evaluate the relationship between cooking oil fume exposure and lung cancer among Chinese nonsmoking women. Thirteen articles containing three population-based case–control and ten hospital-based case–control studies were included in this meta-analysis. These studies with a total of 3,596 lung cancer women and 6,082 healthy controls were analyzed by RevMan 5.3. Fixed effects model or random effects model was used to obtain pooled estimates of risk ratio. The risk ratios with a 95% CI were 1.74 (95% CI =1.57–1.94 and 2.11 (95% CI =1.54–2.89, respectively. Cooking oil fume exposure as well as not using a kitchen ventilator when cooking was significantly associated with lung cancer among nonsmoking women (Z=10.07, P<0.00001; Z=4.65, P<0.00001. Cooking oil fume exposure, especially lacking a fume extractor, may increase the risk of lung cancer among Chinese nonsmoking women. Keywords: cooking oil fume exposure, lung cancer, meta-analysis, nonsmoking women 

Hydrothermal stability of silica, hybrid silica and Zr-doped hybrid silica membranes

NARCIS (Netherlands)

ten Hove, Marcel; Luiten-Olieman, Mieke W.J.; Huiskes, Cindy; Nijmeijer, Arian; Winnubst, Louis

2017-01-01

Hybrid silica membranes have demonstrated to possess a remarkable hydrothermal stability in pervaporation and gas separation processes allowing them to be used in industrial applications. In several publications the hydrothermal stability of pure silica or that of hybrid silica membranes are

The Relationship of Welding Fume Exposure, Smoking, and Pulmonary Function in Welders.

Science.gov (United States)

Roach, Laura L

2018-01-01

The purpose of this study was to explore the relationship between occupational exposure to welding fumes and pulmonary function in an effort to add supportive evidence and clarity to the current body of research. This study utilized a retrospective chart review of pulmonary function testing and pulmonary questionnaires already available in charts from preplacement physicals to the most recent test. When comparing smokers to nonsmokers, utilizing multiple regression and controlling for age and percentage of time using a respirator, years welding was statistically significant at p = .04. Data support that smoking has a synergistic effect when combined with welding fume exposure on pulmonary decline.

Systemic serum amyloid A as a biomarker for exposure to zinc and/or copper-containing metal fumes.

Science.gov (United States)

Baumann, R; Gube, M; Markert, A; Davatgarbenam, S; Kossack, V; Gerhards, B; Kraus, T; Brand, P

2018-01-01

Zinc- and copper-containing welding fumes increase systemic C-reactive protein (CRP). The aim of this study was to investigate the performance of the biomarkers serum amyloid A (SAA) and soluble vascular cell adhesion molecule-1 (VCAM-1) in this regard. Fifteen male subjects were exposed under controlled conditions to welding fumes containing either zinc, or copper, or copper and zinc for 6 h. Plasma samples were collected before, 6 and 24 h after start of exposure and biomarkers therein were measured by electrochemiluminescent assay. For each exposure, systemic concentrations of systemic SAA, but not VCAM-1, increased significantly at 24 h after exposure start compared with baseline ("copper only": P=0.0005, "zinc only": P=0.027, "copper and zinc": P=0.001). SAA showed a wider range of concentrations than did CRP and its levels increased up to 19-fold after welding fume exposure. The recognition of copper as a potential harmful component in welding fumes, also independent from zinc, deserves further consideration. SAA might represent a new sensitive biomarker for potential subclinical sterile inflammation after inhalation of copper- and/or zinc-containing welding fumes. As elevations of CRP and SAA protein have both been linked to a higher risk for cardiovascular disease, these findings might particularly be important for long-term welders.

Isothermal model investigation of fume extraction systems for the scrap burner at Appleby Frodingham

Energy Technology Data Exchange (ETDEWEB)

Robinson, D.

1976-08-01

Model tests have been made on three suggested schemes for improving the efficiency of fume collection on the scrap burning installation in the Anchor BOS plant at Appleby Frodingham. In particular the usefulness of air curtains as a means of containing the fume has been examined. CO/sub 2/ tracer measurements, and photographs using smoke for visualization have allowed the assessment of the collection efficiencies of the three schemes, and some alterative solutions have been investigated using similar methods. (GRA)

Lightweight combustion residues-based structural materials for use in mines. Quarterly report, 1 December 1994--28 February 1995

Energy Technology Data Exchange (ETDEWEB)

Chugh, Yoginder P.; Zhang, Yuzhuo; Ghosh, A.K.; Palmer, S.R; Peng, Suping, Xiao, Y. [Southern Illinois Univ., Carbondale, IL (United States)

1995-12-31

The overall goal of this project is to develop, design and test artificial supports (post and crib members) for use in mines manufactured from coal combustion by-product (CCB) based lightweight structural materials. The lightweight cement-fly ash grout with density ranging from 70 to 110 pcf has been developed incorporating very high volume (50--60 % of whole solid materials) fly ash. Characterization of individual component materials for the CCB-based structural materials has been performed for Class F fly ash, ASTM Type I cement, lime, silica fume, polypropylene fibers, protein-based foam, water-reducing agents, and calcium chloride. During the past quarter, we emphasized on screening mix designs and establishing mixing and curing procedures. We have demonstrated for the first time that cellular cement-fly ash grout can be developed with very low water: cement ratio (0.32--0.45). After forming, all the samples in the molds were moist cured in a chamber for 24-hours, at 90% relatively humidity (RH) and at 72{degrees}F. They were then demolded and transferred to a low pressure steam chamber (150{degrees}F and 100% RH). After steaming for 24 hours the samples were removed to a moist cure chamber prior to testing.

Evaluation of one-step luminescent cyanoacrylate fuming.

Science.gov (United States)

Khuu, Alicia; Chadwick, Scott; Spindler, Xanthe; Lam, Rolanda; Moret, Sébastien; Roux, Claude

2016-06-01

One-step luminescent cyanoacrylates have recently been introduced as an alternative to the conventional cyanoacrylate fuming methods. These new techniques do not require the application of a luminescent post-treatment in order to enhance cyanoacrylate-developed fingermarks. In this study, three one-step polymer cyanoacrylates: CN Yellow Crystals (Aneval Inc.), PolyCyano UV (Foster+Freeman Ltd.) and PECA Multiband (BVDA), and one monomer cyanoacrylate: Lumikit™ (Crime Scene Technology), were evaluated against a conventional two-step cyanoacrylate fuming method (Cyanobloom (Foster+Freeman Ltd.) with rhodamine 6G stain). The manufacturers' recommended conditions or conditions compatible with the MVC™ 1000/D (Foster+Freeman Ltd.) were assessed with fingermarks aged for up to 8 weeks on non-porous and semi-porous substrates. Under white light, Cyanobloom generally gave better development than the one-step treatments across the substrates. Similarly when viewed under the respective luminescent conditions, Cyanobloom with rhodamine 6G stain resulted in improved contrast against the one-step treatments except on polystyrene, where PolyCyano UV and PECA Multiband gave better visualisation. Rhodamine 6G post-treatment of one-step samples did not significantly enhance the contrast of any of the one-step treatments against Cyanobloom/rhodamine 6G-treated samples. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Effect of Admixtures on the Yield Stresses of Cement Pastes under High Hydrostatic Pressures.

Science.gov (United States)

Yim, Hong Jae; Kim, Jae Hong; Kwon, Seung Hee

2016-03-02

When cement-based materials are transported at a construction site, they undergo high pressures during the pumping process. The rheological properties of the materials under such high pressures are unknown, and estimating the workability of the materials after pumping is a complex problem. Among various influential factors on the rheology of concrete, this study investigated the effect of mineral and chemical admixtures on the high-pressure rheology. A rheometer was fabricated that could measure the rheological properties while maintaining a high pressure to simulate the pumping process. The effects of superplasticizer, silica fume, nanoclay, fly ash, or ground granulated blast furnace slag were investigated when mixed with two control cement pastes. The water-to-cement ratios were 0.35 and 0.50.

Effect of Admixtures on the Yield Stresses of Cement Pastes under High Hydrostatic Pressures

Directory of Open Access Journals (Sweden)

Hong Jae Yim

2016-03-01

Full Text Available When cement-based materials are transported at a construction site, they undergo high pressures during the pumping process. The rheological properties of the materials under such high pressures are unknown, and estimating the workability of the materials after pumping is a complex problem. Among various influential factors on the rheology of concrete, this study investigated the effect of mineral and chemical admixtures on the high-pressure rheology. A rheometer was fabricated that could measure the rheological properties while maintaining a high pressure to simulate the pumping process. The effects of superplasticizer, silica fume, nanoclay, fly ash, or ground granulated blast furnace slag were investigated when mixed with two control cement pastes. The water-to-cement ratios were 0.35 and 0.50.

Properties of concretes and wood composites using a phosphate-based binder

Science.gov (United States)

Hong, Luong Thanh

Magnesium potassium phosphate ceramics are from the family of phosphate-based cements which can be used as alternatives to Portland cements. In this study, concretes and wood composites were produced using magnesium potassium phosphate ceramic binders and supplementary materials including fly ash, sand, silica fume and sawdust. Bentonite, Delvo Stabilizer and baking soda were used as additives to increase the workability and the setting time of the fresh mixutres and decrease the density of the hardened products. The materials were then reinforced with chopped glass-fibers or textile glass-fabrics to increase their hardened properties. At 50% fly ash by total mass of the binder, the concretes had compressive strength and density of 33 MPa and 2170 kg/m3, respectively, after 90 days of simple curing. At 20% fly ash by total mass of the binder, the wood composites had compressive strength and density of 13 MPa and 1320 kg/m3, respectively, after 90 days. The flexural strengths were about 10% to 47% of the corresponding cylinder compressive strengths for these mixes. Increases in both compressive and flexural strengths for these mixes were observed with the addition of chopped glass-fibers or textile glass-fabrics.

Association between cooking oil fume exposure and lung cancer among Chinese nonsmoking women: a meta-analysis.

Science.gov (United States)

Xue, Yingbo; Jiang, Ying; Jin, Shan; Li, Yong

2016-01-01

Lung cancer has been the main cause of cancer death around the world. Cigarette smoking has been identified as a risk factor for lung cancer in males. However, the etiological factors in nonsmoking women remain elusive. A meta-analysis was conducted to evaluate the relationship between cooking oil fume exposure and lung cancer among Chinese nonsmoking women. Thirteen articles containing three population-based case-control and ten hospital-based case-control studies were included in this meta-analysis. These studies with a total of 3,596 lung cancer women and 6,082 healthy controls were analyzed by RevMan 5.3. Fixed effects model or random effects model was used to obtain pooled estimates of risk ratio. The risk ratios with a 95% CI were 1.74 (95% CI =1.57-1.94) and 2.11 (95% CI =1.54-2.89), respectively. Cooking oil fume exposure as well as not using a kitchen ventilator when cooking was significantly associated with lung cancer among nonsmoking women (Z=10.07, Poil fume exposure, especially lacking a fume extractor, may increase the risk of lung cancer among Chinese nonsmoking women.

Effect of Fly Ash Fortification in the Manufacture Process of Making Concrete towards Characteristics of Concrete in Sulfuric Acid Solution

Directory of Open Access Journals (Sweden)

Asep Handaya Saputra

2015-12-01

Full Text Available Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH within concrete. The reduced content of Ca(OH through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete. In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics (compressive strength and durability under acidic environment, the research is conducted by varying the fly ash composition ranging from 0%, 5%, 25%, 50%, up to 75%, and the concentration of H22SO solution as an immersion medium ranging from 0%, 5%, 10%, up to 15% (v/v. The research is carried out by immersing the concrete samples for 4 days in H4 solution with various concentrations. Characterization of concrete’s durability and compressive strength is reviewed from the concrete’s weight loss percentage and reduction of concrete’s compressive strength percentage after immersion. Based on the research results, for each variation of H2SO concentration used, the minimum concrete’s weight loss percentage (maximum durability and the minimum reduction of concrete’s compressive strength percentage is found in the use of fly ash by 75%. For each concentration variations of H42SO solution as an immersion medium ranging from 5%, 10%, up to 15% (v/v, the minimum concrete’s weight loss percentage was 0.47%, 0.87%, 1.28% (respectively, whilst the minimum reduction of concrete’s compressive strength percentage was 5.71%, 14.29%, 17.14% (respectively. It was concluded that the use of fly ash can improve the durability and minimize the reduction of compressive strength of concrete

Hepatotoxic and Nephrotoxic Effects of Petroleum Fumes on Petrol ...

African Journals Online (AJOL)

The present study was conducted to evaluate the hepatotoxic and nephrotoxic effects of petroleum fumes on male and female petrol attendants. Investigations had been carried out on thirty (30) adult petrol attendants from different filling stations in Ibadan metropolis of Nigeria with ten (10) healthy adults as control. All the ...

Levels and patterns of polycyclic aromatic hydrocarbons in fly ash generated in Coal-fired power plant

International Nuclear Information System (INIS)

Ajmal, P.Y.; Sahu, S.K.; Pandit, G.G.; Shukla, V.K.; Puranik, V.D.

2005-01-01

The burning of pulverized coal to produce energy for generation of electricity in thermal power plants results in huge quantity of coal ash of varying properties. Because of the increase in electricity production, the amount of ash produced will increase proportionally. A large percentage of coal fly ash is comprised of relatively inert materials, such as silica and other trace and toxic elements. The coal ash also contain organic constituents of potential environmental concern. So far, very few studies on characterization of organic constituents in fly ash have been reported in the literature. In the present study, the fly ashes generated from the power stations are investigated regarding the distribution of 14 PAHs. The total amount of PAHs in the fly ash samples varied between 45.8 ng/g and 257.7 ng/g. Lower molecular weight (MW) PAHs, were found to be predominant in the fly ash samples. The concentration of Benzo(a)pyrene, which is the most potent carcinogenic PAH was found to vary between 0.8 ng/g to 6.3 ng/g with a mean concentration of 2.5 ng/g. (author)

Enhanced Ionic Conductivity of Poly(Ethylene Imine) Phosphate

DEFF Research Database (Denmark)

Senadeera, G.K.R.; Careem, M.A.; Skaarup, Steen

1996-01-01

The conductivity of mixtures of phosphoric acid with poly(ethylene imine) has been studied, and it was found that the conductivity of such mixtures with high acid content can be enhanced by the addition of highly dispersed silica (fumed silica). At the same time, silica addition increases the sti...

Cycloolefin copolymer/fumed silica nanocomposites

Czech Academy of Sciences Publication Activity Database

Dorigato, A.; Pegoretti, A.; Fambri, L.; Šlouf, Miroslav; Kolařík, Jan

2011-01-01

Roč. 119, č. 6 (2011), s. 3393-3402 ISSN 0021-8995 R&D Projects: GA ČR GA106/09/1348 Institutional research plan: CEZ:AV0Z40500505 Keywords : creep * nanocomposites * polyolefins Subject RIV: JI - Composite Materials Impact factor: 1.289, year: 2011

Characterization of the early pulmonary inflammatory response associated with PTFE fume exposure

Science.gov (United States)

Johnston, C. J.; Finkelstein, J. N.; Gelein, R.; Baggs, R.; Oberdorster, G.; Clarkson, T. W. (Principal Investigator)

1996-01-01

Heating of polytetrafluoroethylene (PTFE) has been described to release fumes containing ultrafine particles (approximately 18 nm diam). These fumes can be highly toxic in the respiratory tract inducing extensive pulmonary edema with hemorrhagic inflammation. Fischer-344 rats were exposed to PTFE fumes generated by temperatures ranging from 450 to 460 degrees C for 15 min at an exposure concentration of 5 x 10(5) particles/cm3, equivalent to approximately 50 micrograms/m3. Responses were examined 4 hr post-treatment when these rats demonstrated 60-85% neutrophils (PMNs) in their lung lavage. Increases in abundance for messages encoding the antioxidants manganese superoxide dismutase and metallothionein (MT) increased 15- and 40-fold, respectively. For messages encoding the pro- and anti-inflammatory cytokines: inducible nitric oxide synthase, interleukin 1 alpha, 1 beta, and 6 (IL-1 alpha, IL-1 beta, and IL-6), macrophage inflammatory protein-2, and tumor necrosis factor-alpha (TNF alpha) increases of 5-, 5-, 10-, 40-, 40-, and 15-fold were present. Vascular endothelial growth factor, which may play a role in the integrity of the endothelial barrier, was decreased to 20% of controls. In situ sections were hybridized with 33P cRNA probes encoding IL-6, MT, surfactant protein C, and TNF alpha. Increased mRNA abundance for MT and IL-6 was expressed around all airways and interstitial regions with MT and IL-6 demonstrating similar spatial distribution. Large numbers of activated PMNs expressed IL-6, MT, and TNF alpha. Additionally, pulmonary macrophages and epithelial cells were actively involved. These observations support the notion that PTFE fumes containing ultrafine particles initiate a severe inflammatory response at low inhaled particle mass concentrations, which is suggestive of an oxidative injury. Furthermore, PMNs may actively regulate the inflammatory process through cytokine and antioxidant expression.

Effects of welding fumes on nuclear air cleaning system carbon adsorber banks

Energy Technology Data Exchange (ETDEWEB)

Roberson, P.W. [Duke Power Company, Huntersville, NC (United States)

1997-08-01

Standard Technical Specifications for nuclear air cleaning systems include requirements for surveillance tests following fire, painting, or chemical release in areas communicating with the affected system. To conservatively implement this requirement, many plants categorize welding as a chemical release process, and institute controls to ensure that welding fumes do not interact with carbon adsorbers in a filter system. After reviewing research data that indicated welding had a minimal impact on adsorber iodine removal efficiency, further testing was performed with the goal of establishing a welding threshold. It was anticipated that some quantity of weld electrodes could be determined that had a corresponding detrimental impact on iodine removal efficiency for the exposed adsorber. This value could be used to determine a conservative sampling schedule that would allow the station to perform laboratory testing to ensure system degradation did not occur without a full battery of surveillance tests. A series of tests was designed to demonstrate carbon efficiency versus cumulative welding fume exposure. Three series of tests were performed, one for each of three different types of commonly used weld electrodes. Carbon sampling was performed at baseline conditions, and every five pounds of electrode thereafter. Two different laboratory tests were performed for each sample; one in accordance with ASTM 3803/1989 at 95% relative humidity and 30 degrees C, and another using the less rigorous conditions of 70% relative humidity and 80 degrees C. Review of the test data for all three types of electrodes failed to show a significant correlation between carbon efficiency degradation and welding fume exposure. Accordingly, welding is no longer categorized as a `chemical release process` at McGuire Nuclear Station, and limits on welding fume interaction with ventilation systems have been eliminated. 4 refs., 3 figs., 1 tab.

Urinary β2 Microglobulin in Workers Exposed to Arc Welding Fumes

Directory of Open Access Journals (Sweden)

Khosro Sadeghniiat-Haghighi

2011-11-01

Full Text Available Welding is a process in which two or more metals are attached by the use of heat and, in some cases, pressure. Direct exposure and inhalation of welding fumes causes acute and chronic side effects in humans. Kidney damage is one of these important side effects. β2 microglobulin is an 11.8 kilodalton protein and levels increase in the case of some inflammatory and viral diseases, or kidney malfunction and autoimmune diseases. In this study measurements of β2 microglobulin were used as a criterion for assessing effects on the kidneys of workers exposed to welding fumes. The study population were electric arc welders in an industrial plant in Tehran, Iran. For control we selected workers who did not have any exposure to welding fumes. Both groups were selected on the basis of a questionnaire and the consideration of criteria for inclusion and exclusion. In the end 50 cases and 50 controls were chosen. A urine sample was collected from all participants and urinary pH was set to between 6-8 using NaOH (1M. Sample transportation to the laboratory complied with the related standards. The samples were assessed using the ORG 5BM kit. For quantitative assessment of β2 microglobulin we used the Enzyme-linked Immunosorbent Assay (ELISA method. The ages of the welders ranged from 21 to 48 years (mean=30.5±5.9 yrs and of controls from 23 to 56 years (mean=31.8±5.9 yrs. Mean employment duration was 7.86±5.01years (range 2 to 27 years for welders. Mean β2 microglobulin level was 0.10±0.096 μg/ml in welders and 0.11±0.06 in controls. This difference was not statistically significant (P=0.381. In conclusion we don't find that exposure to electric arc welding fumes cause a significant change in urinary β2 microglobulin compared to the control group.

Airborne nanoparticle exposures associated with the manual handling of nanoalumina and nanosilver in fume hoods

International Nuclear Information System (INIS)

Tsai, Su-Jung; Ada, Earl; Isaacs, Jacqueline A.; Ellenbecker, Michael J.

2009-01-01

Manual handling of nanoparticles is a fundamental task of most nanomaterial research; such handling may expose workers to ultrafine or nanoparticles. Recent studies confirm that exposures to ultrafine or nanoparticles produce adverse inflammatory responses in rodent lungs and such particles may translocate to other areas of the body, including the brain. An important method for protecting workers handling nanoparticles from exposure to airborne nanoparticles is the laboratory fume hood. Such hoods rely on the proper face velocity for optimum performance. In addition, several other hood design and operating factors can affect worker exposure. Handling experiments were performed to measure airborne particle concentration while handling nanoparticles in three fume hoods located in different buildings under a range of operating conditions. Nanoalumina and nanosilver were selected to perform handling experiments in the fume hoods. Air samples were also collected on polycarbonate membrane filters and particles were characterized by scanning electron microscopy. Handling tasks included transferring particles from beaker to beaker by spatula and by pouring. Measurement locations were the room background, the researcher's breathing zone and upstream and downstream from the handling location. Variable factors studied included hood design, transfer method, face velocity/sash location and material types. Airborne particle concentrations measured at breathing zone locations were analyzed to characterize exposure level. Statistics were used to test the correlation between data. The test results found that the handling of dry powders consisting of nano-sized particles inside laboratory fume hoods can result in a significant release of airborne nanoparticles from the fume hood into the laboratory environment and the researcher's breathing zone. Many variables were found to affect the extent of particle release including hood design, hood operation (sash height, face velocity

Global metabolomic profiling reveals an association of metal fume exposure and plasma unsaturated fatty acids.

Directory of Open Access Journals (Sweden)

Yongyue Wei

Full Text Available Welding-associated air pollutants negatively affect the health of exposed workers; however, their molecular mechanisms in causing disease remain largely unclear. Few studies have systematically investigated the systemic toxic effects of welding fumes on humans.To explore the effects of welding fumes on the plasma metabolome, and to identify biomarkers for risk assessment of welding fume exposure.The two-stage, self-controlled exploratory study included 11 boilermakers from a 2011 discovery panel and 8 boilermakers from a 2012 validation panel. Plasma samples were collected pre- and post-welding fume exposure and analyzed by chromatography/mass spectrometry.Eicosapentaenoic or docosapentaenoic acid metabolic changes post-welding were significantly associated with particulate (PM2.5 exposure (p<0.05. The combined analysis by linear mixed-effects model showed that exposure was associated with a statistically significant decline in metabolite change of eicosapentaenoic acid [β(95% CI = -0.013(-0.022 ≈ -0.004; p = 0.005], docosapentaenoic acid n3 [β(95% CI = -0.010(-0.018 ≈ -0.002; p = 0.017], and docosapentaenoic acid n6 [β(95% CI = -0.007(-0.013 ≈ -0.001; p = 0.021]. Pathway analysis identified an association of the unsaturated fatty acid pathway with exposure (p Study-2011 = 0.025; p Study-2012 = 0.021; p Combined = 0.009. The functional network built by these fatty acids and their interactive genes contained significant enrichment of genes associated with various diseases, including neoplasms, cardiovascular diseases, and lipid metabolism disorders.High-dose exposure of metal welding fumes decreases unsaturated fatty acids with an exposure-response relationship. This alteration in fatty acids is a potential biological mediator and biomarker for exposure-related health disorders.

Airborne nanoparticle exposures associated with the manual handling of nanoalumina and nanosilver in fume hoods

Energy Technology Data Exchange (ETDEWEB)

Tsai, Su-Jung, E-mail: candace.umass@gmail.com; Ada, Earl [University of Massachusetts Lowell, NSF Center for High-rate Nanomanufacturing (CHN) (United States); Isaacs, Jacqueline A. [Northeastern University, NSF Center for High-rate Nanomanufacturing (CHN) (United States); Ellenbecker, Michael J. [University of Massachusetts Lowell, NSF Center for High-rate Nanomanufacturing (CHN) (United States)

2009-01-15

Manual handling of nanoparticles is a fundamental task of most nanomaterial research; such handling may expose workers to ultrafine or nanoparticles. Recent studies confirm that exposures to ultrafine or nanoparticles produce adverse inflammatory responses in rodent lungs and such particles may translocate to other areas of the body, including the brain. An important method for protecting workers handling nanoparticles from exposure to airborne nanoparticles is the laboratory fume hood. Such hoods rely on the proper face velocity for optimum performance. In addition, several other hood design and operating factors can affect worker exposure. Handling experiments were performed to measure airborne particle concentration while handling nanoparticles in three fume hoods located in different buildings under a range of operating conditions. Nanoalumina and nanosilver were selected to perform handling experiments in the fume hoods. Air samples were also collected on polycarbonate membrane filters and particles were characterized by scanning electron microscopy. Handling tasks included transferring particles from beaker to beaker by spatula and by pouring. Measurement locations were the room background, the researcher's breathing zone and upstream and downstream from the handling location. Variable factors studied included hood design, transfer method, face velocity/sash location and material types. Airborne particle concentrations measured at breathing zone locations were analyzed to characterize exposure level. Statistics were used to test the correlation between data. The test results found that the handling of dry powders consisting of nano-sized particles inside laboratory fume hoods can result in a significant release of airborne nanoparticles from the fume hood into the laboratory environment and the researcher's breathing zone. Many variables were found to affect the extent of particle release including hood design, hood operation (sash height, face

Altered ion transport in normal human bronchial epithelial cells following exposure to chemically distinct metal welding fume particles

Energy Technology Data Exchange (ETDEWEB)

Fedan, Jeffrey S., E-mail: jsf2@cdc.gov; Thompson, Janet A.; Meighan, Terence G.; Zeidler-Erdely, Patti C.; Antonini, James M.

2017-07-01

Welding fume inhalation causes pulmonary toxicity, including susceptibility to infection. We hypothesized that airway epithelial ion transport is a target of fume toxicity, and investigated the effects of fume particulates from manual metal arc-stainless steel (MMA-SS) and gas metal arc-mild steel (GMA-MS) on ion transport in normal human bronchial epithelium (NHBE) cultured in air-interface. MMA-SS particles, more soluble than GMA-MS particles, contain Cr, Ni, Fe and Mn; GMA-MS particles contain Fe and Mn. MMA-SS or GMA-MS particles (0.0167–166.7 μg/cm{sup 2}) were applied apically to NHBEs. After 18 h transepithelial potential difference (V{sub t}), resistance (R{sub t}), and short circuit current (I{sub sc}) were measured. Particle effects on Na{sup +} and Cl¯ channels and the Na{sup +},K{sup +},2Cl¯-cotransporter were evaluated using amiloride (apical), 5-nitro-2-[(3-phenylpropyl)amino]benzoic acid (NPPB, apical), and bumetanide (basolateral), respectively. MMA-SS (0.0167–16.7 μg/cm{sup 2}) increased basal V{sub t}. Only 16.7 μg/cm{sup 2} GMA-MS increased basal V{sub t} significantly. MMA-SS or GMA-MS exposure potentiated I{sub sc} responses (decreases) to amiloride and bumetanide, while not affecting those to NPPB, GMA-MS to a lesser degree than MMA-SS. Variable effects on R{sub t} were observed in response to amiloride, and bumetanide. Generally, MMA-SS was more potent in altering responses to amiloride and bumetanide than GMA-MS. Hyperpolarization occurred in the absence of LDH release, but decreases in V{sub t}, R{sub t}, and I{sub sc} at higher fume particulate doses accompanied LDH release, to a greater extent for MMA-SS. Thus, Na{sup +} transport and Na{sup +},K{sup +},2Cl¯-cotransport are affected by fume exposure; MMA-MS is more potent than GMA-MS. Enhanced Na{sup +} absorption and decreased airway surface liquid could compromise defenses against infection. - Highlights: • Welding fume particle toxicity was investigated in human bronchial

Highly durable and low permeable concrete for LLW facilities

International Nuclear Information System (INIS)

Yanagibashi, Kunio; Saito, Toshio; Odagawa, Masaro.

1997-01-01

Concrete used for LLW facilities is required to be highly durable. The authors evaluated concrete containing glycol ether derivatives and silica fume as admixtures. Compressive strength, diffusion coefficient of water, depth of accelerated carbonation, drying shrinkage, depth of chlorides penetration and resistance to freezing and thawing were investigated using concrete specimens. Compressive strength, depth of accelerated carbonation, diffusion coefficient of 137 Cs were investigated using mortar specimens before and after irradiation of gamma rays. Results showed that using glycol ether derivatives and silica fume was effective in improving the durability. (author)

Simultaneous adsorption of dyes and heavy metals from multicomponent solutions using fly ash

International Nuclear Information System (INIS)

Visa, Maria; Bogatu, Cristina; Duta, Anca

2010-01-01

In wastewaters originating from dye industry there are amounts of dyes (very common methyl orange, methylene blue-MB) and heavy metals (cadmium, copper, nickel mainly from the organo-metallic dyes). They tend to adsorb in a competitive process and modify the substrate. Advanced removal is usually proposed via adsorption and the use of modified fly ash as a substrate is sustainable solution. The main constituents of fly ash (silica, alumina, iron oxide and un-burned carbon), are the priority compounds which favour the heavy metal adsorption and are active sites in dyes' adsorption processes. The paper studies the effect of MB adsorbed on the fly ash surface on the removal efficiency of cadmium, copper and nickel ionic species from complex, multi-cationic dye solutions. The adsorption efficiency and kinetics are evaluated from the complex, multicomponent systems and possible influences are discussed. High efficiencies are obtained at low heavy metal concentrations (as it is the real case for the dyes industry) whereas at medium values, competitive processes lower the individual efficiencies of copper, nickel or cadmium from mixtures.

Two-Step Method for Preparation of NaA-X Zeolite Blend from Fly Ash for Removal of Cesium ions

International Nuclear Information System (INIS)

El-Naggar, M.R.; El-Kamash, A.M.; El-Dessouky, M.I.; Ghonaim, A.K.

2008-01-01

Pure zeolites can be synthesized from silica extracts obtained from fly ash by alkaline leaching. The extraction potential of industrial by-product fly ash was investigated under repeated fusion process conditions. The amount of extracted silica was 131.43 g/kg ash while the amount extracted alumina was limited to 41.72 g/kg ash. The results of zeolite synthesis from the Si-bearing extracts demonstrated that pure zeolites with high cation exchange capacity (4.624 m eq/g) can be produced. The sorption potential of synthesized A-X zeolite blend for the removal of cesium ions has been investigated. The influences of ph, contact time and temperature have been reported. Thermodynamic parameters such as changes in Gibbs free energy (δG degree), enthalpy (δH degree) and entropy (δS degree) were calculated. A comparison of kinetic models applied to the sorption data was evaluated for pseudo-first order, pseudo-second order and homogeneous particle diffusion models. The results showed that both the pseudo-second order and the homogeneous particle diffusion models were found to best correlate the experimental rate data

Effects of some anaesthetics on honeybees: nitrous oxide, carbon dioxide, ammonium nitrate smoker fumes

Energy Technology Data Exchange (ETDEWEB)

Simpson, J

1954-08-01

Honeybees were apparently unaffected by atmospheric oxygen concentrations between 7% and 100%, and only became motionless when the oxygen concentration was less than 2%. The effects of nitrous oxide-oxygen mixtures differed little, if at all, from those nitrogen-oxygen mixtures. Bees were not visibly affected by carbon dioxide concentrations up to 10-15% but they became motionless if the concentration exceeded 40-45%. Fumes produced by adding ammonium nitrate to the fuel in a beekeeper's smoker were found to contain hydrogen cyanide or cyanogen. Their effectiveness as an anaesthetic may be due to this or to some unidentified component, but not to nitrous oxide. All three anaesthetics caused foraging bees to stop collecting pollen, and accelerated the retrogression of the pharyngeal glands of young bees. Anaesthesia of a few bees in a colony with nitrous oxide, carbon dioxide, or ammonium nitrate smoker fumes did not appear to inhibit their drift back to the original site when their hive was moved, nor was any reduction in drifting observed when a whole colony was moved while anaesthetized with ammonium nitrate smoker fumes. 4 tables.

Increased levels of oxidative DNA damage attributable to cooking-oil fumes exposure among cooks.

Science.gov (United States)

Ke, Yuebin; Cheng, Jinquan; Zhang, Zhicheng; Zhang, Renli; Zhang, Zhunzhen; Shuai, Zhihong; Wu, Tangchun

2009-07-01

Previous investigations have indicated that cooks are exposed to polycyclic aromatic hydrocarbons (PAHs) from cooking-oil fumes. However, Emission of PAH and their carcinogenic potencies from cooking oil fumes sources have not been investigated among cooks. To investigate the urinary excretion of a marker for oxidative DNA damage, 8-hydroxydeoxyguanosine (8-OHdG), in different groups of cooks and different exposure groups, and to study the association between 8-OHdG and 1-hydroxypyrene(1-OHP), a biological marker for PAH exposure. Urine samples were collected from different groups of cooks (n = 86) and from unexposed controls (n = 36); all were male with similar age and smoking habits. The health status, occupational history, smoking, and alcohol consumption 24 h prior to sampling was estimated from questionnaires. The urine samples were frozen for later analyses of 8-OHdG and 1-OHP levels by high-performance liquid chromatography. Excretion in urine of 8-OHdG was similar for controls (mean 1.2micromol/mol creatinine, n = 36), and for those who had been in the kitchen with an exhaust-hood operating (mean 1.5micromol/mol creatinine, n = 45). Cooks exposed to cooking-oil fumes without exhaust-hood operation had significantly increased excretion of 8-OHdG (mean 2.3micromol/mol creatinine, n = 18), compared with controls. The urinary levels of ln 1-OHP and ln 8-OHdG were still significantly correlated in a multiple regression analysis. The results indicate that exposure to PAH or possibly other compounds in cooking-oil fumes may cause oxidative DNA damage.

Thermal transformation of bioactive caffeic acid on fumed silica seen by UV-Vis spectroscopy, thermogravimetric analysis, temperature programmed desorption mass spectrometry and quantum chemical methods.

Science.gov (United States)

Kulik, Tetiana V; Lipkovska, Natalia O; Barvinchenko, Valentyna M; Palyanytsya, Borys B; Kazakova, Olga A; Dudik, Olesia O; Menyhárd, Alfréd; László, Krisztina

2016-05-15

Thermochemical studies of hydroxycinnamic acid derivatives and their surface complexes are important for the pharmaceutical industry, medicine and for the development of technologies of heterogeneous biomass pyrolysis. In this study, structural and thermal transformations of caffeic acid complexes on silica surfaces were studied by UV-Vis spectroscopy, thermogravimetric analysis, temperature programmed desorption mass spectrometry (TPD MS) and quantum chemical methods. Two types of caffeic acid surface complexes are found to form through phenolic or carboxyl groups. The kinetic parameters of the chemical reactions of caffeic acid on silica surface are calculated. The mechanisms of thermal transformations of the caffeic chemisorbed surface complexes are proposed. Thermal decomposition of caffeic acid complex chemisorbed through grafted ester group proceeds via three parallel reactions, producing ketene, vinyl and acetylene derivatives of 1,2-dihydroxybenzene. Immobilization of phenolic acids on the silica surface improves greatly their thermal stability. Copyright © 2016 Elsevier Inc. All rights reserved.

Profiling stainless steel welding processes to reduce fume emissions, hexavalent chromium emissions and operating costs in the workplace.

Science.gov (United States)

Keane, Michael; Siert, Arlen; Stone, Samuel; Chen, Bean T

2016-01-01

Nine gas metal arc welding (GMAW) processes for stainless steel were assessed for fume generation rates, fume generation rates per g of electrode consumed, and emission rates for hexavalent chromium (Cr(6+)). Elemental manganese, nickel, chromium, iron emissions per unit length of weld, and labor plus consumables costs were similarly measured. Flux-cored arc welding and shielded metal arc (SMAW) processes were also studied. The objective was to identify the best welding processes for reducing workplace exposures, and estimate costs for all processes. Using a conical chamber, fumes were collected, weighed, recovered, and analyzed by inductively coupled atomic emission spectroscopy for metals, and by ion chromatography for Cr(6+). GMAW processes used were Surface Tension Transfer, Regulated Metal Deposition, Cold Metal Transfer, short-circuit, axial spray, and pulsed spray modes. Flux-cored welding used gas shielding; SMAW used E308 rods. Costs were estimated as dollars per m length of a ¼ in (6.3 mm) thick horizontal butt weld; equipment costs were estimated as ratios of new equipment costs to a 250 ampere capacity SMAW welding machine. Results indicate a broad range of fume emission factors for the processes studied. Fume emission rates per g of electrode were lowest for GMAW processes such as pulsed-spray mode (0.2 mg/g), and highest for SMAW (8 mg fume/g electrode). Emission rates of Cr(6+) ranged from 50-7800 µg/min, and Cr(6+) generation rates per g electrode ranged from 1-270 µg/g. Elemental Cr generation rates spanned 13-330 µg/g. Manganese emission rates ranged from 50-300 µg/g. Nickel emission rates ranged from 4-140 µg/g. Labor and consumables costs ranged from $3.15 (GMAW pulsed spray) to $7.40 (SMAW) per meter of finished weld, and were measured or estimated for all 11 processes tested. Equipment costs for some processes may be as much as five times the cost of a typical SMAW welding machine. The results show that all of the GMAW processes in this

Effect Of Inhalation Exposure To Kerosene And Petrol-Fumes On ...

African Journals Online (AJOL)

Changes in total body weight, some anaemia-diagnostic indices (haematocrit or packed cell volume (PCV), haemoglobin (Hb) and total serum protein) were determined in rats (Wistar albino strain) after 2 weeks of 4 hours daily inhalation exposure to ungraded concentrations of kerosene and petrol fumes. The results ...

A proton-exchange membrane prepared by the radiation grafting of styrene and silica into polytetrafluoroethylene films

Science.gov (United States)

Yu, Hongyan; Shi, Jianheng; Zeng, Xinmiao; Bao, Mao; Zhao, Xinqing

2009-07-01

A polytetrafluoroethylene (PTFE) based organic-inorganic hybrid proton-exchange membrane was prepared from simultaneous radiation grafting of styrene (St) into porous PTFE membrane with the in situ sol-gel reaction of tetraethoxysilane (TEOS) followed by sulfonation in fuming sulfonic acid. The effect of radiation on the sol-gel reaction was studied. The results show that radiation promotes the sol-gel reaction with the help of St at room temperature. Incorporated silica gel helps to produce higher degree of grafting (DOG). SEM analysis was conducted to confirm that the inorganic silicon oxide was introduced to produce hybrid membrane in this work. The proton conductivity of membrane evaluated using electrochemical impedance spectroscopy is much higher (14.3×10 -2 S cm -1) than that of Nafion ® 117 at temperature of 80 °C with acceptable water uptake 51 wt%.

Exposure to welding fumes increases lung cancer risk among light smokers but not among heavy smokers: evidence from two case-control studies in Montreal.

Science.gov (United States)

Vallières, Eric; Pintos, Javier; Lavoué, Jérôme; Parent, Marie-Élise; Rachet, Bernard; Siemiatycki, Jack

2012-08-01

We investigated relationships between occupational exposure to gas and arc welding fumes and the risk of lung cancer among workers exposed to these agents throughout the spectrum of industries. Two population-based case-control studies were conducted in Montreal. Study I (1979-1986) included 857 cases and 1066 controls, and Study II (1996-2001) comprised 736 cases and 894 controls. Detailed job histories were obtained by interview and evaluated by an expert team of chemist-hygienists to estimate degree of exposure to approximately 300 substances for each job. Gas and arc welding fumes were among the agents evaluated. We estimated odds ratios (ORs) and 95% confidence intervals (CIs) of lung cancer using logistic regression, adjusting for smoking history and other covariates. The two studies provided similar results, so a pooled analysis was conducted. Among all subjects, no significant association was found between lung cancer and gas welding fumes (OR = 1.1; 95% CI = 0.9-1.4) or arc welding fumes (OR = 1.0; 95% CI = 0.8-1.2). However, when restricting attention to light smokers, there was an increased risk of lung cancer in relation to gas welding fumes (OR = 2.9; 95% CI = 1.7-4.8) and arc welding fumes (OR = 2.3; 95% CI = 1.3-3.8), with even higher OR estimates among workers with the highest cumulative exposures. In conclusion, there was no detectable excess risk of lung cancer due to welding fumes among moderate to heavy smokers; but among light smokers we found an excess risk related to both types of welding fumes.

Study on construction method of concrete in the underground research laboratory. 2

International Nuclear Information System (INIS)

Iriya, Keishiro; Mikami, Tetsuji; Akiyoshi, Kenji; Uegaki, Yoshiaki

2002-02-01

The underground research laboratory, which will be constructed in Horonobe, plays a role of demonstration of construction technique upon nuclear waste repositories. Low alkalinity cement is one of candidates for repositories as a cementitious material in order to prevent alteration of bentonite and rock by hyper alkaline solution. JNC has developed a low alkalinity cement (HFSC) which contains a lot of fly ash, and has studied the physical and chemical properties by laboratory test. However workability which is required for construction procedure of repositories has not been studied enough yet. This study shows if requirements in actual construction, such as shotcreting, self-compacting, and, grouting, are fulfilled, and if the workability is preferable for tunneling construction. It is demonstrated that HFSC is applicable for shotcreting by testing in a modeled tunnel. It is pointed out that re-bars have a possibility of corrosion in low alkalinity cement. In-site test for saline water which may accelerate corrosion is started by setting specimen made in last year. Analyzing and assessing will be done next year. Construction method of tunnel lining is investigated in case of applying pre-cast segments. Self-compacting concrete is adopted, since added silica-fume needs superplasticizer and its workability is very flowable. Two piece of segment were made for the section which designed for a ordinary urban tunnel. It is noted that pre-casting concrete can be made by HFSC. Super fine cement powder for grouting which indicate low alkalinity can be selected by combination of grinned lime stone powder and silica fume with grinned ordinary Portland cement. The items to be improved toward using in Horonobe construction are pointed out by results of this study and summarized a study plan is described. Major problem to be solved is delaying compressive strength generation of HFSC. It is recognized in shotcrete and self-compacting concrete. Selecting types of fly ash and

Increase in oxidative stress levels following welding fume inhalation: a controlled human exposure study.

Science.gov (United States)

Graczyk, Halshka; Lewinski, Nastassja; Zhao, Jiayuan; Sauvain, Jean-Jacques; Suarez, Guillaume; Wild, Pascal; Danuser, Brigitta; Riediker, Michael

2016-06-10

Tungsten inert gas (TIG) welding represents one of the most widely used metal joining processes in industry. It has been shown to generate a large majority of particles at the nanoscale and to have low mass emission rates when compared to other types of welding. Despite evidence that TIG fume particles may produce reactive oxygen species (ROS), limited data is available for the time course changes of particle-associated oxidative stress in exposed TIG welders. Twenty non-smoking male welding apprentices were exposed to TIG welding fumes for 60 min under controlled, well-ventilated settings. Exhaled breathe condensate (EBC), blood and urine were collected before exposure, immediately after exposure, 1 h and 3 h post exposure. Volunteers participated in a control day to account for oxidative stress fluctuations due to circadian rhythm. Biological liquids were assessed for total reducing capacity, hydrogen peroxide (H2O2), malondialdehyde (MDA), and 8-hydroxy-2'-deoxyguanosine (8-OHdG) concentrations at each time point. A linear mixed model was used to assess within day and between day differences. Significant increases in the measured biomarkers were found at 3 h post exposure. At 3 h post exposure, we found a 24 % increase in plasma-H2O2 concentrations ([95%CI: 4 % to 46 %], p = 0.01); a 91 % increase in urinary-H2O2 ([2 % to 258 %], p = 0.04); a 14 % increase in plasma-8-OHdG ([0 % to 31 %], p = 0.049); and a 45 % increase in urinary-8-OHdG ([3 % to 105 %], p = 0.03). Doubling particle number concentration (PNC) exposure was associated with a 22 % increase of plasma-8-OHdG at 3 h post exposure (p = 0.01). A 60-min exposure to TIG welding fume in a controlled, well-ventilated setting induced acute oxidative stress at 3 h post exposure in healthy, non-smoking apprentice welders not chronically exposed to welding fumes. As mass concentration of TIG welding fume particles is very low when compared to other types of welding, it is

Aggregate-cement paste transition zone properties affecting the salt-frost damage of high-performance concretes

International Nuclear Information System (INIS)

Cwirzen, Andrzej; Penttala, Vesa

2005-01-01

The influence of the cement paste-aggregate interfacial transition zone (ITZ) on the frost durability of high-performance silica fume concrete (HPSFC) has been studied. Investigation was carried out on eight non-air-entrained concretes having water-to-binder (W/B) ratios of 0.3, 0.35 and 0.42 and different additions of condensed silica fume. Studies on the microstructure and composition of the cement paste have been made by means of environmental scanning electron microscope (ESEM)-BSE, ESEM-EDX and mercury intrusion porosimetry (MIP) analysis. The results showed that the transition zone initiates and accelerates damaging mechanisms by enhancing movement of the pore solution within the concrete during freezing and thawing cycles. Cracks filled with ettringite were primarily formed in the ITZ. The test concretes having good frost-deicing salt durability featured a narrow transition zone and a decreased Ca/Si atomic ratio in the transition zone compared to the bulk cement paste. Moderate additions of silica fume seemed to densify the microstructure of the ITZ

Blunted behavioral and c Fos responses to acidic fumes in the African naked mole-rat.

Science.gov (United States)

LaVinka, Pamela Colleen; Park, Thomas J

2012-01-01

Acidosis in the skin triggers activation of pain pathways and behaviors indicative of pain in vertebrates. The exception is the naked mole-rat, the only known vertebrate to show physiological and behavioral insensitivity to acid pain in the skin. The goal of the present study was to determine behavioral and physiological responses of this species to airborne acidic fumes, which would be expected to affect the trigeminal pain pathway in other species. Behaviorally, naked mole-rats did not avoid fumes from moderately high concentrations of acetic acid (10 and 20%), and c Fos labeling showed no increase in activity in the trigeminal nuclei and nucleus tractus solitarius. In contrast, these concentrations triggered behavioral aversion and increased Fos activity in other laboratory rodents. For a very high concentration of acetic acid (50%), naked mole-rats showed significant avoidance behavior and increased Fos labeling in the nucleus tractus solitarius caudal region, which receives vagal chemosensory information. However, there was no increase in trigeminal labeling, and in fact, activity significantly decreased. This pattern is opposite of that associated with another irritant, ammonia fumes, which elicited an increase in trigeminal but not nucleus tractus solitarius Fos labeling, and no behavioral avoidance. Behavioral avoidance of acidic fumes, but no increased labeling in the trigeminal pain nucleus is consistent with the notion of adaptations to blunt acid pain, which would be advantageous for naked mole-rats as they normally live under chronically high levels of acidosis-inducing CO(2).

Blunted behavioral and c Fos responses to acidic fumes in the African naked mole-rat.

Directory of Open Access Journals (Sweden)

Pamela Colleen LaVinka

Full Text Available Acidosis in the skin triggers activation of pain pathways and behaviors indicative of pain in vertebrates. The exception is the naked mole-rat, the only known vertebrate to show physiological and behavioral insensitivity to acid pain in the skin. The goal of the present study was to determine behavioral and physiological responses of this species to airborne acidic fumes, which would be expected to affect the trigeminal pain pathway in other species. Behaviorally, naked mole-rats did not avoid fumes from moderately high concentrations of acetic acid (10 and 20%, and c Fos labeling showed no increase in activity in the trigeminal nuclei and nucleus tractus solitarius. In contrast, these concentrations triggered behavioral aversion and increased Fos activity in other laboratory rodents. For a very high concentration of acetic acid (50%, naked mole-rats showed significant avoidance behavior and increased Fos labeling in the nucleus tractus solitarius caudal region, which receives vagal chemosensory information. However, there was no increase in trigeminal labeling, and in fact, activity significantly decreased. This pattern is opposite of that associated with another irritant, ammonia fumes, which elicited an increase in trigeminal but not nucleus tractus solitarius Fos labeling, and no behavioral avoidance. Behavioral avoidance of acidic fumes, but no increased labeling in the trigeminal pain nucleus is consistent with the notion of adaptations to blunt acid pain, which would be advantageous for naked mole-rats as they normally live under chronically high levels of acidosis-inducing CO(2.

A new method for infrared imaging of air currents in and around critical hazard fume hoods

International Nuclear Information System (INIS)

Mulac, W.A.; McCreary, J.R.; Schmalz, H.

1992-01-01

A real time method of measuring and recording the efficacy of vapor containment in and around critical hazard fume hoods is being developed. An infrared camera whose response is restricted to a spectral range that overlaps a strong absorption band in a non-toxic gas is used to render real-time video images of the presence and flow of the gas. The gas, nitrous oxide, is ejected in a continuous stream in and around fume hoods that are to be certified capable of containing hazardous fumes. The principle advantage is that various scenarios of air flow displacement in and outside the hood can be easily investigated; the principle limitation is the necessity of high tracer gas concentration to obtain strong visualizations. We hope that this technique can be found to be an effective and safe method to test hoods in locations that were built before present regulations were promulgated

Inhalation of gas metal arc-stainless steel welding fume promotes lung tumorigenesis in A/J mice.

Science.gov (United States)

Falcone, Lauryn M; Erdely, Aaron; Meighan, Terence G; Battelli, Lori A; Salmen, Rebecca; McKinney, Walter; Stone, Samuel; Cumpston, Amy; Cumpston, Jared; Andrews, Ronnee N; Kashon, Michael; Antonini, James M; Zeidler-Erdely, Patti C

2017-08-01

Epidemiologic studies suggest an increased risk of lung cancer with exposure to welding fumes, but controlled animal studies are needed to support this association. Oropharyngeal aspiration of collected "aged" gas metal arc-stainless steel (GMA-SS) welding fume has been shown by our laboratory to promote lung tumor formation in vivo using a two-stage initiation-promotion model. Our objective in this study was to determine whether inhalation of freshly generated GMA-SS welding fume also acts as a lung tumor promoter in lung tumor-susceptible mice. Male A/J mice received intraperitoneal (IP) injections of corn oil or the chemical initiator 3-methylcholanthrene (MCA; 10 µg/g) and 1 week later were exposed by whole-body inhalation to air or GMA-SS welding aerosols for 4 h/d × 4 d/w × 9 w at a target concentration of 40 mg/m 3 . Lung nodules were enumerated at 30 weeks post-initiation. GMA-SS fume significantly promoted lung tumor multiplicity in A/J mice initiated with MCA (16.11 ± 1.18) compared to MCA/air-exposed mice (7.93 ± 0.82). Histopathological analysis found that the increased number of lung nodules in the MCA/GMA-SS group were hyperplasias and adenomas, which was consistent with developing lung tumorigenesis. Metal deposition analysis in the lung revealed a lower deposited dose, approximately fivefold compared to our previous aspiration study, still elicited a significant lung tumorigenic response. In conclusion, this study demonstrates that inhaling GMA-SS welding fume promotes lung tumorigenesis in vivo which is consistent with the epidemiologic studies that show welders may be at an increased risk for lung cancer.

Problem of industrial fumes in the forested valleys of Savoy

Energy Technology Data Exchange (ETDEWEB)

Bossavy, J

1962-01-01

A study of injury to forest trees in the Maurienne valley, caused by F in the fumes from aluminum factories was made. Of the local conifers, Pinus sylvestris was the most susceptible, followed by Picea abies and Abies alba; Larch has so far proved resistant, as have broadleaved deciduous species.

A Study on the quantification of hydration and the strength development mechanism of cementitious materials including amorphous phases by using XRD/Rietveld method

International Nuclear Information System (INIS)

Yamada, Kazuo; Hoshino, Seiichi; Hirao, Hiroshi; Yamashita, Hiroki

2008-01-01

X-ray diffraction (XRD)/Rietveld method was applied to measure the phase composition of cement. The quantative analysis concerning the progress of hydration was accomplished in an error of about the maximum 2-3% in spite of including amorphous materials such as blast furnace slag, fly ash, silica fume and C-S-H. The influence of the compressive strength on the lime stone fine powder mixture material was studied from the hydration analysis by Rietveld method. The two stages were observed in the strength development mechanism of cement; the hydration promotion of C 3 S in the early stage and the filling of cavities by carbonate hydrate for the longer term. It is useful to use various mixture materials for the formation of the resource recycling society and the durability improvement of concrete. (author)

Physicochemical and toxicological characteristics of welding fume derived particles generated from real time welding processes.

Science.gov (United States)

Chang, Cali; Demokritou, Philip; Shafer, Martin; Christiani, David

2013-01-01

Welding fume particles have been well studied in the past; however, most studies have examined welding fumes generated from machine models rather than actual exposures. Furthermore, the link between physicochemical and toxicological properties of welding fume particles has not been well understood. This study aims to investigate the physicochemical properties of particles derived during real time welding processes generated during actual welding processes and to assess the particle size specific toxicological properties. A compact cascade impactor (Harvard CCI) was stationed within the welding booth to sample particles by size. Size fractionated particles were extracted and used for both off-line physicochemical analysis and in vitro cellular toxicological characterization. Each size fraction was analyzed for ions, elemental compositions, and mass concentration. Furthermore, real time optical particle monitors (DustTrak™, TSI Inc., Shoreview, Minn.) were used in the same welding booth to collect real time PM2.5 particle number concentration data. The sampled particles were extracted from the polyurethane foam (PUF) impaction substrates using a previously developed and validated protocol, and used in a cellular assay to assess oxidative stress. By mass, welding aerosols were found to be in coarse (PM 2.5–10), and fine (PM 0.1–2.5) size ranges. Most of the water soluble (WS) metals presented higher concentrations in the coarse size range with some exceptions such as sodium, which presented elevated concentration in the PM 0.1 size range. In vitro data showed size specific dependency, with the fine and ultrafine size ranges having the highest reactive oxygen species (ROS) activity. Additionally, this study suggests a possible correlation between welders' experience, the welding procedure and equipment used and particles generated from welding fumes. Mass concentrations and total metal and water soluble metal concentrations of welding fume particles may be

Exposure to welding fumes increases lung cancer risk among light smokers but not among heavy smokers: evidence from two case–control studies in Montreal

Science.gov (United States)

Vallières, Eric; Pintos, Javier; Lavoué, Jérôme; Parent, Marie-Élise; Rachet, Bernard; Siemiatycki, Jack

2012-01-01

We investigated relationships between occupational exposure to gas and arc welding fumes and the risk of lung cancer among workers exposed to these agents throughout the spectrum of industries. Two population-based case–control studies were conducted in Montreal. Study I (1979–1986) included 857 cases and 1066 controls, and Study II (1996–2001) comprised 736 cases and 894 controls. Detailed job histories were obtained by interview and evaluated by an expert team of chemist–hygienists to estimate degree of exposure to approximately 300 substances for each job. Gas and arc welding fumes were among the agents evaluated. We estimated odds ratios (ORs) and 95% confidence intervals (CIs) of lung cancer using logistic regression, adjusting for smoking history and other covariates. The two studies provided similar results, so a pooled analysis was conducted. Among all subjects, no significant association was found between lung cancer and gas welding fumes (OR = 1.1; 95% CI = 0.9–1.4) or arc welding fumes (OR = 1.0; 95% CI = 0.8–1.2). However, when restricting attention to light smokers, there was an increased risk of lung cancer in relation to gas welding fumes (OR = 2.9; 95% CI = 1.7–4.8) and arc welding fumes (OR = 2.3; 95% CI = 1.3–3.8), with even higher OR estimates among workers with the highest cumulative exposures. In conclusion, there was no detectable excess risk of lung cancer due to welding fumes among moderate to heavy smokers; but among light smokers we found an excess risk related to both types of welding fumes. PMID:23342253

Kinetic and Thermodynamics of Methylene Blue Adsorption onto Zero Valent Iron Supported on Mesoporous Silica

Directory of Open Access Journals (Sweden)

Atyaf Khalid Hameed

2016-08-01

Full Text Available Zero valent iron supported on mesoporous silicanano particles (NZVI/MSNs was prepared by the aqueous phase borohydride reduction methods. Prior to the reduction, mesoporous silica nanoparticles (MSNs were prepared through the activation of fumed silica with concentrated HCl by refluxing at 90 °C. FTIR, XRD, FESEM, EDX and BET were used to characterize theadsorbents prepared. BET surface areas of MSNs, NZVI, and NZVI/MSNs were 126, 41, and 72 m2/g for, respectively. The performance of NZVI/MSNs as adsorbent was examined by adsorption of methylene blue (MB, performed in series of batch experiments. In the kinetic studies, pseudo first order and pseudo second order kinetic models were examined. The pseudo second order equation provided the best fit with the experimental data. Thermodynamic studies indicated that the adsorption process is endothermic with ΔH° was 90.53 kJ/mol. Positive ΔS° (300 J/mol and negative ΔG° (-6.42 kJ/mol was recorded, indicating the spontaneous of the adsorption process and naturally favorable. Copyright © 2016 BCREC GROUP. All rights reserved Received: 5th March 2016; Revised: 18th March 2016; Accepted: 18th March 2016 How to Cite: Hameed, A.K., Dewayanto, N., Dongyun, D., Nordin, M.R., Mohd Hasbi Ab. Rahim, M.H.A. (2016. Kinetic and Thermodynamics of Methylene Blue Adsorption onto Zero Valent Iron Supported on Mesoporous Silica. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (2: 250-261 (doi:10.9767/bcrec.11.2.443.250-261 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.11.2.443.250-261

Phase analysis of fume during arc weld brazing of steel sheets with protective coatings

Directory of Open Access Journals (Sweden)

J. Matusiak

2016-04-01

Full Text Available The article presents the results of research of the phase identification and of the quantitative phase analysis of fume generated during Cold Metal Transfer (CMT, ColdArc and Metal Inert Gas / Metal Active Gas (MIG / MAG weld brazing. Investigations were conducted for hot - dip coated steel sheets with zinc (Zn and zinc-iron (Zn - Fe alloy coatings. Arc shielding gases applied during the research-related tests were Ar + O2, Ar + CO2, Ar + H2 and Ar + CO2 + H2 gas mixtures. The analysis of the results covers the influence of the chemical composition of shielding gas on the chemical composition of welding fume.

Silica Nephropathy

Directory of Open Access Journals (Sweden)

N Ghahramani

2010-06-01

Full Text Available Occupational exposure to heavy metals, organic solvents and silica is associated with a variety of renal manifestations. Improved understanding of occupational renal disease provides insight into environmental renal disease, improving knowledge of disease pathogenesis. Silica (SiO2 is an abundant mineral found in sand, rock, and soil. Workers exposed to silica include sandblasters, miners, quarry workers, masons, ceramic workers and glass manufacturers. New cases of silicosis per year have been estimated in the US to be 3600–7300. Exposure to silica has been associated with tubulointerstitial disease, immune-mediated multisystem disease, chronic kidney disease and end-stage renal disease. A rare syndrome of painful, nodular skin lesions has been described in dialysis patients with excessive levels of silicon. Balkan endemic nephropathy is postulated to be due to chronic intoxication with drinking water polluted by silicates released during soil erosion. The mechanism of silica nephrotoxicity is thought to be through direct nephrotoxicity, as well as silica-induced autoimmune diseases such as scleroderma and systemic lupus erythematosus. The renal histopathology varies from focal to crescentic and necrotizing glomerulonephritis with aneurysm formation suggestive of polyarteritis nodosa. The treatment for silica nephrotoxicity is non-specific and depends on the mechanism and stage of the disease. It is quite clear that further research is needed, particularly to elucidate the pathogenesis of silica nephropathy. Considering the importance of diagnosing exposure-related renal disease at early stages, it is imperative to obtain a thorough occupational history in all patients with renal disease, with particular emphasis on exposure to silica, heavy metals, and solvents.

Effect of paint fumes on histoarchitecture of the testes of adult male ...

African Journals Online (AJOL)

abdominal incision was performed after which one testis was received from each rats, preserved in 10% formal saline and further processed for histological study using Hematoxylin and eosin technique. Results: The testes of the paint fumes ...

Some Durability Characteristics of Micro Silica and Nano Silica Contained Concrete

Directory of Open Access Journals (Sweden)

Mohammed Salah Nasr

2016-12-01

Full Text Available This paper aims to investigate the influence of replacement of cement with nano and micro silica admixtures on some durability properties of concrete such as water absorption, chloride content and pH tests. Three replacement ratios (5%,10%,15% of micro silica and four replacement proportions (0.5%,1.5%,3%,5% for nano silica were used in this study. Two exposure conditions were considered for chloride content test: wetting-drying and full immersing exposure in 6% of chloride ions solution, NaCl type. Results showed that mixes of %5 micro silica and 5% nano silica had lower content of chloride (about 0.19% and 0.18% for wetting-drying and full immersing exposure respectively. For water absorption test, all mixes incorporated micro and nano silica, except for %5 micro silica mix, showed lower absorption than control mixes. For pH test, results indicated that the adding of nano and micro silica didn’t affect adversely the alkalinity of concrete.

X-ray fluorescence analysis of welding fume particles

International Nuclear Information System (INIS)

Carsey, T.P.

1982-01-01

A commercial standard filter set and two laboratory-made standard filter sets are compared via the analysis of generated welding fume samples by X-ray fluorescence. The latter standards are made by (1) hydrophobic-edge membrane filters spiked with prepared metal ion solutions, and (2) filters through which a dispersion of metal oxide powder in isopropanol has been drawn. The results are presented in table form. Precision (Pre) is the relative standard deviation of the six samples. Four main conclusions are enumerated

Acute Inhalation Exposure to Titanium Ethanolate as a Possible Cause of Metal Fume Fever

Directory of Open Access Journals (Sweden)

M Ahmadimanesh

2014-04-01

Full Text Available Occupational inhalation exposure to noxious agents is not uncommon. Herein, we present a 26-year-old male student who had accidental acute inhalation exposure to a large quantity of titanium ethanolate and hydrogen chloride in chemistry lab. He was referred to the emergency department of our hospital with low-grade fever, dyspnea, headache, fatigue and myalgia. After 24 hrs of symptomatic treatment (oxygen therapy and acetaminophen, the fever was subsided and the patient discharged home in a good clinical condition. The presented symptoms could be interpreted as a form of metal fume fever. It can therefore be concluded that organo-metallic compound of titanium metal may have the potential to produce metal fume fever in human.

STUDI PEMANFAATAN LIMBAH B3 KARBIT DAN FLY ASH SEBAGAI BAHAN CAMPURAN BETON SIAP PAKAI (BSP (STUDI KASUS : PT. VARIA USAHA BETON

Directory of Open Access Journals (Sweden)

Nindya Rossavina Dewi

2016-03-01

Full Text Available Fly ash is widely used as concrete’s builder because it contains quite high silica (SiO2 approximately 58,20%. Fly ash can increase concrete power pressure and contains characteristic like cement. Fly ash contains low CaO approximately 3,30% so it needs other material to increase CaO on concrete. CaO found on karbit waste it contained CaO approximately 56,5%. Method of concrete making and technical feasibility test on this research use SNI standar (SNI 03-2834-2000. Environmental feasibility test use Toxicity Characteristic Leaching Procedur (TCLP according PP No. 101 tahun 2014. The results of this research show that the use of karbit waste and fly ash can increase concrete power pressure at age of immersion 28 days. Concrete power pressure with 25% fly ash addition and carbide waste 2,5%;5%;10%; and 15% are 22,05 MPa, 19,43 MPa, 18,59 MPa, 16.09 MPa. Concrete power pressure increase 34,2%; 18,25%; dan 13,14%. Heavy metal concentration at concrete with fly ash 25% and carbide waste 2,5% ; 5% ; 10% are below standard. The best composition is the mixing between 25% fly ash dan10% carbide waste which has Concrete power pressure 18,59 MPa.

Evaluation of the Pulmonary Toxicity of a Fume Generated from a Nickel-, Copper-Based Electrode to be Used as a Substitute in Stainless Steel Welding

Science.gov (United States)

Antonini, James M; Badding, Melissa A; Meighan, Terence G; Keane, Michael; Leonard, Stephen S; Roberts, Jenny R

2014-01-01

Epidemiology has indicated a possible increase in lung cancer among stainless steel welders. Chromium (Cr) is a primary component of stainless steel welding fume. There is an initiative to develop alternative welding consumables [nickel (Ni)- and copper (Cu)-based alloys] that do not contain Cr. No study has been performed to evaluate the toxicity of fumes generated from Ni- and Cu-based consumables. Dose–response and time-course effects on lung toxicity of a Ni- and Cu-based welding fume (Ni–Cu WF) were examined using an in vivo and in vitro bioassay, and compared with two other well-characterized welding fumes. Even though only trace amounts of Cr were present, a persistent increase in lung injury and inflammation was observed for the Ni–Cu WF compared to the other fumes. The difference in response appears to be due to a direct cytotoxic effect by the Ni–Cu WF sample on lung macrophages as opposed to an elevated production of reactive oxygen species (ROS). PMID:25392698

Refreshing the Aged Latent Fingerprints with Ionizing Radiation Prior to the Cyanoacrylate Fuming Procedure: A Preliminary Study.

Science.gov (United States)

Ristova, Mimoza M; Radiceska, Pavlina; Bozinov, Igorco; Barandovski, Lambe

2016-05-01

One of the crucial factors determining the cyanoacrylate deposit quality over latent fingerprints appeared to be the extent of the humidity. This work focuses on the enhancement/refreshment of age-degraded latent fingerprints by irradiating the samples with UV, X-ray, or thermal neutrons prior to the cyanoacrylate (CA) fuming. Age degradation of latent fingerprints deposited on glass surfaces was examined through the decrease in the number of characteristic minutiae counts over time. A term "critical day" was introduced for the time at which the average number of identifiable minutiae definitions drops to one-half. Fingerprints older than their "critical day" were exposed to either UV, X-ray, or thermal neutrons. Identical reference samples were kept unexposed. All samples, both reference and irradiated, were developed during a single CA fuming procedure. Comparative latent fingerprint analysis showed that exposure to ionizing radiation enhances the CA fuming, yielding a 20-30% increase in average minutiae count. © 2015 American Academy of Forensic Sciences.

Comparison of Powder Dusting and Cyanoacrylate Fuming Techniques in Retrieving Latent Fingerprint Exposed to Environment Conditions

International Nuclear Information System (INIS)

Mayalvanan, Y.; Sri Pawita Albakri Amir Hamzah; Chuan, L.L.; Muhamad Hilmi Baba; Amidon Anan

2014-01-01

Latent fingerprints are one of the best evidence to prove the presence of an individuals presence at the crime scene. There are many techniques available for a successful fingerprint lifting. Two of the most common ones are fingerprint powder dusting and cyanoacrylate fuming. This research aims to compare both techniques and determine which has a higher success rate in retrieving fingerprints exposed to local environmental conditions for three days. Fingerprint samples were collected from 18 subjects on glass, perspex and aluminium slides. These samples were then exposed to local environmental conditions for three days. The fingerprints were then developed using the aforementioned techniques. Based on the results, it can be safely said that, fuming results in clearer fingerprints and more minutiae can be found from the retrieved fingerprints even with exposure to less than optimum local conditions. This proves that fuming is a better fingerprint lifting method to resolve latent fingerprint compared to powder dusting. Surface on which the fingerprint is retrieved from influences the quality of clarity of a latent fingerprint. (author)

Self-curing concrete types; water retention and durability

Directory of Open Access Journals (Sweden)

Magda I. Mousa

2015-09-01

This study was carried out to compare among concretes without or with silica fume (SF along with chemical type of shrinkage reducing admixture, polyethylene-glycol (Ch, and leca as self-curing agents for water retention even at elevated temperature (50 °C and their durability. The cement content of 400 kg/m3, silica fume of 15% by weight of cement, polyethylene-glycol of 2% by weight of cement, pre-saturated lightweight aggregate (leca 15% by volume of sand and water with Ch/binder ratio of 0.4 were selected in this study. Some of the physical and mechanical properties were determined periodically up to 28 days in case of exposure to air curing in temperature of (25 °C and (50 °C while up to 6 months of exposure to 5% of carbon dioxide and wet/dry cycles in 8% of sodium chloride for durability study. The concrete mass loss and the volumetric water absorption were measured, to evaluate the water retention of the investigated concretes. Silica fume concrete either without or with Ch gave the best results under all curing regimes; significant water retention and good durability properties.

Study of water permeability in concrete by neutron and gamma-ray techniques

International Nuclear Information System (INIS)

Abd El-Monem, A.M.M.

2010-01-01

water infiltration in various building materials , namely concrete used for buildings basement and underwater construction is the main concern of the studies performed in this thesis. The studies aim to develop a nuclear techniques for investigation a concrete mixes with different additives capable to decrease concrete porosity and intern resist water propagation inside concrete materials without any deterioration of concrete physical and mechanical properties . These issues were achieved through the preparation of ordinary concrete mixes with different percentages of silica fume. Concrete samples of different shape and geometries were made to study water diffusion when the concrete samples are submerged in water for different periods of time. The concrete samples were first sealed by molten asphalt from all sides expect two opposite faces to ensure water migration only along one direction. Water infiltration in concrete samples with different percentages of silica fume and submerged in tap and seawater for different periods of time was studied by neutrons and gamma techniques. Also, water propagation in mortar samples with different percentages of silica fume was studied by electrical methods based on measuring the variation in electrical conductivity of these samples.

Comparison between electron-beam and chemical crosslinking of silicone rubber

Energy Technology Data Exchange (ETDEWEB)

Frounchi, Masoud [Polymer Engineering Group, Department of Chemical and Petroleum Engineering, Sharif University of Technology, Azadi Ave, Tehran (Iran, Islamic Republic of)]. E-mail: frounchi@sharif.edu; Dadbin, Susan [Yazd Processing Center, Atomic Energy Organization of Iran, Tehran (Iran, Islamic Republic of); Panahinia, Farhad [Polymer Engineering Group, Department of Chemical and Petroleum Engineering, Sharif University of Technology, Azadi Ave, Tehran (Iran, Islamic Republic of)

2006-02-15

Silicone rubber (SR) was irradiated by electron beam over a dose range of 50-300 kGy in the absence of chemical reagents. Molecular weight between crosslinks (M {sub c}) in the network of SB was determined by two methods of solvent swelling and modulus of elasticity. The network structure of the elastomer crosslinked by electron beam irradiation and chemical vulcanization was compared. Mechanical tests were performed to determine shore hardness, tensile elongation, strength and modulus of the samples. It was found that SR is effectively crosslinked by electron beam irradiation. The tensile strength, hardness, modulus and elongation of irradiated SR were higher than peroxide-crosslinked SR. The optimum dose for the neat rubber was 150 kGy which reduced to 50 kGy with addition of 10 wt.% fumed silica. The synergistic effect of fumed silica was verified by M {sub c} measurements which showed a dramatic decrease in presence of fumed silica in the rubber. The synergism in properties was also verified by comparing the modulus values calculated from the Guth-Smallwood equation and experimental data. Absence of chemical reagents in irradiated SR samples makes them a proper choice for medical applications.

Corrosion resistance of nickel alloys with chromium and silicon to the red fuming nitric acid

International Nuclear Information System (INIS)

Gurvich, L.Ya.; Zhirnov, A.D.

1994-01-01

Corrosion and electrochemical behaviour of binary Ni-Cr, Ni-Si nickel and ternary Ni-Cr-Si alloys in the red fuming nitric acid (RFNA) (8-% of HNO 3 +20% of N 2 O 4 ) is studied. It is shown that nickel alloying with chromium improves its corrosion resistance to the red fuming nitric acid. Nickel alloying with silicon in quantities of up to 5 % reduces, and up to 10%-increases abruptly the corrosion resistance with subsequent decrease of the latter after the further increase of concentration. Ni-15% of Cr alloy alloying with silicon increases monotonously the corrosion resistance. 10 refs., 7 figs., 3 tabs

Microporous silica membranes

DEFF Research Database (Denmark)

Boffa, Vittorio; Yue, Yuanzheng

2012-01-01

Hydrothermal stability is a crucial factor for the application of microporous silica-based membranes in industrial processes. Indeed, it is well established that steam exposure may cause densification and defect formation in microporous silica membranes, which are detrimental to both membrane...... permeability and selectivity. Numerous previous studies show that microporous transition metal doped-silica membranes are hydrothermally more stable than pure silica membranes, but less permeable. Here we present a quantitative study on the impact of type and concentration of transition metal ions...... on the microporous structure, stability and permeability of amorphous silica-based membranes, providing information on how to design chemical compositions and synthetic paths for the fabrication of silica-based membranes with a well accessible and highly stabile microporous structure....

Feasibility of mobile health game "Fume" in supporting tobacco-related health literacy among early adolescents: A three-armed cluster randomized design.

Science.gov (United States)

Parisod, Heidi; Pakarinen, Anni; Axelin, Anna; Löyttyniemi, Eliisa; Smed, Jouni; Salanterä, Sanna

2018-05-01

New interventions supporting health literacy and a tobacco-free lifestyle in adolescence are needed to narrow the widening gap in existing health inequalities. Health games offer potential and could be utilized for example in school healthcare, but more research is needed to increase the understanding of the effects of game elements in health interventions. The aim of this feasibility study is to determine the short-term effectiveness of the tobacco-related mobile health game Fume and a non-gamified website in comparison with a no-intervention control group, regarding tobacco-related health literacy among 10-13-year-old early adolescents. In addition, we compare the demand for and acceptability of Fume to that of the website. In total, 151 early adolescents participated in this single-blinded, three-armed cluster randomized trial. The participants from three municipalities in southwest Finland were randomly allocated between a group with access to the health game Fume (n = 61), a group with access to the website (n = 47), and a group with no intervention (n = 43). The intervention groups first participated in a 20-min training session with Fume/the website, and then had two weeks to use Fume/the website based on their own interest. Short-term effectiveness was measured by primary (anti-smoking self-efficacy) and secondary (smoking outcome expectations, attitudes towards tobacco use, tobacco-use motives, motivation to decline tobacco use in the future, and knowledge about tobacco) outcomes derived from the theory-based determinants of tobacco-related health literacy and evaluated with self-assessment questionnaires at baseline and post-intervention (after a two-week follow-up). For evaluating the demand, the actual use of Fume/the website was tracked during the two-week period. Regarding acceptability, the raised interest towards Fume/the website and opinions about the interventions were evaluated post-intervention. Differences were tested with the Mc

Micro and macrolevel properties of fly ash blended self compacting concrete

International Nuclear Information System (INIS)

Guru Jawahar, J.; Sashidhar, C.; Ramana Reddy, I.V.; Annie Peter, J.

2013-01-01

Highlights: ► Effect of class F fly ash on micro and macrolevel properties of self compacting concrete is studied. ► Decrease in microcracking width and Ca/Si ratio was observed in SCC with the age. ► Micro and macrolevels properties of SCC were compared to those of conventional concrete. ► Micro and macrolevel properties of SCC are reasonably correlated. ► Recommendation of SCC mix with medium compressive strength of 32 MPa for the building constructions. - Abstract: This investigation is mainly focused on the effect of class F fly ash on the micro and macrolevel properties of self compacting concrete (SCC) after 28, 56 and 112 days of curing. The microlevel properties studied were the microcrack widths between aggregate and paste and atomic Calcium–Silica (Ca/Si) ratio. The macrolevel properties studied were compressive strength, modulus of elasticity and splitting tensile strength. A conventional concrete (CC) having an equivalent 28-day SCC compressive strength has also been examined at different ages. Scanning electron microscope (SEM) analysis was carried to examine the width of microcracks and energy dispersive X-ray analysis (EDAX) was carried out to determine the chemical elements of both SCC and CC. Studies revealed that pozzolanic action of class F fly ash improved the microlevel properties of SCC with age by reducing the microcracking width and Ca/Si ratio and thus enhanced the macrolevel properties

Environmentally-Friendly Dense and Porous Geopolymers Using Fly Ash and Rice Husk Ash as Raw Materials

Directory of Open Access Journals (Sweden)

Daniele Ziegler

2016-06-01

Full Text Available This paper assesses the feasibility of two industrial wastes, fly ash (FA and rice husk ash (RHA, as raw materials for the production of geopolymeric pastes. Three typologies of samples were thus produced: (i halloysite activated with potassium hydroxide and nanosilica, used as the reference sample (HL-S; (ii halloysite activated with rice husk ash dissolved into KOH solution (HL-R; (iii FA activated with the alkaline solution realized with the rice husk ash (FA-R. Dense and porous samples were produced and characterized in terms of mechanical properties and environmental impact. The flexural and compressive strength of HL-R reached about 9 and 43 MPa, respectively. On the contrary, the compressive strength of FA-R is significantly lower than the HL-R one, in spite of a comparable flexural strength being reached. However, when porous samples are concerned, FA-R shows comparable or even higher strength than HL-R. Thus, the current results show that RHA is a valuable alternative to silica nanopowder to prepare the activator solution, to be used either with calcined clay and fly ash feedstock materials. Finally, a preliminary evaluation of the global warming potential (GWP was performed for the three investigated formulations. With the mix containing FA and RHA-based silica solution, a reduction of about 90% of GWP was achieved with respect to the values obtained for the reference formulation.

Novel insecticide strategies such as phototoxic dyes in adult fruit fly control and suppression programmes

International Nuclear Information System (INIS)

Moreno, Daniel S.; Mangan, Robert L.

2000-01-01

researchers began to test the idea of attracticides. Protein-hydrolysate baits were first used in Hawaii for the control of the Oriental fruit fly, Bactrocera dorsalis (Hendel). The spray mixture contained protein hydrolysate, sugar, and parathion (Steiner 1952). In 1956, malathion (a fumigant, contact, stomach poison) was combined with protein bait to eradicate the C. capitata from Florida (Steiner et al. 1961). A mixture of technical grade malathion (> 95%) and NuLure (Protein Insecticide Bait 7 or PIB-7) at a ratio of 1:4 (malathion:NuLure) was used to eradicate C. capitata from Brownsville, Texas (Stephenson and McClung 1966). Lopez et al. (1969) also used a malathion-bait combination at the same ratio to control the Mexican fruit fly Anastrepha ludens (Loew), applied at discrete locations; however, they did not elucidate the rationale for their 1:4 ratio. Later, Harris et al. (1971) showed that effectiveness of malathion to kill fruit flies was directly proportional to the ratio of malathion to NuLure; a ratio of 1:4 was more effective than other ratios tested. Thus, flies responding to the attracticide only needed fume exposure, contact, taste, or ingest mixture, whereupon they died in a short time. This may be the reason why the adequacy of the bait in the malathion-bait sprays was not questioned. The main reason for the wide use of malathion is its low mammalian toxicity as well as its low price

A model for prediction of fume formation rate in gas metal arc welding (GMAW), globular and spray modes, DC electrode positive.

Science.gov (United States)

Dennis, J H; Hewitt, P J; Redding, C A; Workman, A D

2001-03-01

Prediction of fume formation rate during metal arc welding and the composition of the fume are of interest to occupational hygienists concerned with risk assessment and to manufacturers of welding consumables. A model for GMAW (DC electrode positive) is described based on the welder determined process parameters (current, wire feed rate and wire composition), on the surface area of molten metal in the arc and on the partial vapour pressures of the component metals of the alloy wire. The model is applicable to globular and spray welding transfer modes but not to dip mode. Metal evaporation from a droplet is evaluated for short time increments and total evaporation obtained by summation over the life of the droplet. The contribution of fume derived from the weld pool and spatter (particles of metal ejected from the arc) is discussed, as are limitations of the model. Calculated droplet temperatures are similar to values determined by other workers. A degree of relationship between predicted and measured fume formation rates is demonstrated but the model does not at this stage provide a reliable predictive tool.

Studies on the Conditioning Methods of Spent Tri-butyl Phosphate/Kerosene and its Degradation Product in Different Matrices

International Nuclear Information System (INIS)

El-Dessouky, M.I.; El-sourougy, M.R.; Abed El-Aziz, M.M.; Aly, H.F.

1999-01-01

The destruction of spent TBP/Kerosene (odourless Kerosene (OK)) with potassium permanganate have been investigated. Comparative studies on the immobilization of spent TBP/Kerosene and its degradation product into different matrices have been carried out. The matrices used include, ordinary Portland cement, silica fume, treated fly ash, epoxy resin and cement mixed with epoxy resin.The different factors affecting solidified waste forms such as, compressive strength, water resistance, thermal stability, chemical resistance, radiological stability and leachability have been investigated. It was found that, epoxy resin and cement mixed with 5,10,20, and 50% of epoxy resin enhance the compressive strength of the solidified waste forms with spent TBP/OK more than that obtained from degradation products. The leaching rates of 152 and 154 Eu and 181 Hf from waste forms containing TBP/OK was found lower than that with degradation product

Effect of SCM on porosity

DEFF Research Database (Denmark)

Canut, Mariana

Pores are an inherent part of cement-based materials. The pores range from nm to cm varying in shape and distribution. The amount, size and distribution of pores affect the engineering properties. As a first approximation, the total porosity affects the mechanical behavior, whereas the size...... blast furnaces, fly ash from coal fired power stations, and silica fume from ferrosilicon production. Studies suggest that the improvement of the strength and durability using SCMs are governed by refinement of the pores in the cement paste. Both the chemical and physical properties of the SCMs...... and connectivity of pores affect durability. Supplementary cementitious materials (SCMs) are being increasingly used as a substitute for Portland cement in the interests of sustainability and to improve the engineering properties of concrete as strength and durability. SCMs are by-products such as slag from iron...

Crystalline Silica Primer

Science.gov (United States)

,

1992-01-01

Crystalline silica is the scientific name for a group of minerals composed of silicon and oxygen. The term crystalline refers to the fact that the oxygen and silicon atoms are arranged in a threedimensional repeating pattern. This group of minerals has shaped human history since the beginning of civilization. From the sand used for making glass to the piezoelectric quartz crystals used in advanced communication systems, crystalline silica has been a part of our technological development. Crystalline silica's pervasiveness in our technology is matched only by its abundance in nature. It's found in samples from every geologic era and from every location around the globe. Scientists have known for decades that prolonged and excessive exposure to crystalline silica dust in mining environments can cause silicosis, a noncancerous lung disease. During the 1980's, studies were conducted that suggested that crystalline silica also was a carcinogen. As a result of these findings, crystalline silica has been regulated under the Occupational Safety and Health Administration's (OSHA) Hazard Communication Standard (HCS). Under HCS, OSHAregulated businesses that use materials containing 0.1% or more crystalline silica must follow Federal guidelines concerning hazard communication and worker training. Although the HCS does not require that samples be analyzed for crystalline silica, mineral suppliers or OSHAregulated

High effective silica fume alkali activator

Indian Academy of Sciences (India)

Unknown

Abstract. Growing demands on the engineering properties of cement based materials and the urgency to decrease unsuitable ecologic impact of Portland cement manufacturing represent significant motivation for the development of new cement corresponding to these aspects. One category represents prospective alkali.

Computational Fluid Dynamic Modeling of Zinc Slag Fuming Process in Top-Submerged Lance Smelting Furnace

Science.gov (United States)

Huda, Nazmul; Naser, Jamal; Brooks, Geoffrey; Reuter, Markus A.; Matusewicz, Robert W.

2012-02-01

Slag fuming is a reductive treatment process for molten zinciferous slags for extracting zinc in the form of metal vapor by injecting or adding a reductant source such as pulverized coal or lump coal and natural gas. A computational fluid dynamic (CFD) model was developed to study the zinc slag fuming process from imperial smelting furnace (ISF) slag in a top-submerged lance furnace and to investigate the details of fluid flow, reaction kinetics, and heat transfer in the furnace. The model integrates combustion phenomena and chemical reactions with the heat, mass, and momentum interfacial interaction between the phases present in the system. A commercial CFD package AVL Fire 2009.2 (AVL, Graz, Austria) coupled with a number of user-defined subroutines in FORTRAN programming language were used to develop the model. The model is based on three-dimensional (3-D) Eulerian multiphase flow approach, and it predicts the velocity and temperature field of the molten slag bath, generated turbulence, and vortex and plume shape at the lance tip. The model also predicts the mass fractions of slag and gaseous components inside the furnace. The model predicted that the percent of ZnO in the slag bath decreases linearly with time and is consistent broadly with the experimental data. The zinc fuming rate from the slag bath predicted by the model was validated through macrostep validation process against the experimental study of Waladan et al. The model results predicted that the rate of ZnO reduction is controlled by the mass transfer of ZnO from the bulk slag to slag-gas interface and rate of gas-carbon reaction for the specified simulation time studied. Although the model is based on zinc slag fuming, the basic approach could be expanded or applied for the CFD analysis of analogous systems.

Fuels planning: science synthesis and integration; environmental consequences fact sheet 12: Water Erosion Prediction Project (WEPP) Fuel Management (FuMe) tool

Science.gov (United States)

William Elliot; David Hall

2005-01-01

The Water Erosion Prediction Project (WEPP) Fuel Management (FuMe) tool was developed to estimate sediment generated by fuel management activities. WEPP FuMe estimates sediment generated for 12 fuel-related conditions from a single input. This fact sheet identifies the intended users and uses, required inputs, what the model does, and tells the user how to obtain the...

Triglycerides, total cholesterol, high density lipoprotein cholesterol and low density lipoprotein cholesterol in rats exposed to premium motor spirit fumes.

Science.gov (United States)

Aberare, Ogbevire L; Okuonghae, Patrick; Mukoro, Nathaniel; Dirisu, John O; Osazuwa, Favour; Odigie, Elvis; Omoregie, Richard

2011-06-01

Deliberate and regular exposure to premium motor spirit fumes is common and could be a risk factor for liver disease in those who are occupationally exposed. A possible association between premium motor spirit fumes and plasma levels of triglyceride, total cholesterol, high density lipoprotein cholesterol and low density lipoprotein cholesterol using a rodent model could provide new insights in the pathology of diseases where cellular dysfunction is an established risk factor. The aim of this study was to evaluate the possible effect of premium motor spirit fumes on lipids and lipoproteins in workers occupationally exposed to premium motor spirit fumes using rodent model. Twenty-five Wister albino rats (of both sexes) were used for this study between the 4(th) of August and 7(th) of September, 2010. The rats were divided into five groups of five rats each. Group 1 rats were not exposed to premium motor spirit fumes (control group), group 2 rats were exposed for 1 hour daily, group 3 for 3 hours daily, group 4 for 5 hours daily and group 5 for 7 hours daily. The experiment lasted for a period of 4 weeks. Blood samples obtained from all the groups after 4 weeks of exposure were used for the estimation of plasma levels of triglyceride, total cholesterol, high density lipoprotein- cholesterol and low density lipoprotein- cholesterol. Results showed significant increase in means of plasma total cholesterol and low density lipoprotein levels (P<0.05). The mean triglyceride and total body weight were significantly lower (P<0.05) in the exposed group when compared with the unexposed. The plasma level of high density lipoprotein, the ratio of low density lipoprotein to high density lipoprotein and the ratio of total cholesterol to high density lipoprotein did not differ significantly in exposed subjects when compared with the control group. These results showed that frequent exposure to petrol fumes may be highly deleterious to the liver cells.

Minimum acceptable face velocities of laboratory fume hoods and guidelines for their classification

International Nuclear Information System (INIS)

Bolton, N.E.; Porter, W.E.; Alcorn, S.P.; Everett, W.S.; Hunt, J.B.; Morehead, J.F.; Higdon, H.F.

1978-06-01

Data developed to support the requirement of a 100 LFM minimum face velocity requirement for laboratory fume hoods are summarized. Also included is a description of the Y-12 test hood as well as guidelines for a hood classification scheme

[Study on the chemical components of edible oil fume in kitchen and its genotoxity on Drosophila].

Science.gov (United States)

Li, S; Wang, Y; Zhang, J; Zhao, X

1999-01-30

To study the chemical components of the condensate of edible oil fume in kitchen and its genotoxicity on Drosophila. Analysis for the chemical components was carried out by gas chromatography and mass spectra (GC/MS) and its genotoxicity was studied by sex linked recessive lethal (SLRL) test in Drosophila. A total of 74 organic compounds were found in samples of condensed oil from the fume in kitchen. It included hydroxylic acids, hydrocarbons, alcohols, esters, aldehydes, ketones, aromatic compounds, and steroids, etc. The total mutagenicity rates in SLRL test induced by the samples at concentrations of 110,320 and 960 mg/L were 0.1732%, 0.4306% and 0.1707% respectively. The sterility rates of the first broods were 2.564%, 2.056% and 2.845% at above 3 concentrations respectively(P < 0.05, as compared with the control). The mutagenicity rate of the second brood at 320 mg/L was 0.530% and that of the third brood at 110 mg/L 0.540%(P < 0.001). Some of the compounds in the condensate of edible oil fume were proved to have high recessive lethal effect and genotoxic effect on the reproductive system of Drosophila.

Development of low alkaline cementitious grouting materials for a deep geological repository

International Nuclear Information System (INIS)

Suzuki, Kenichiro; Miura, Norihiko; Iriya, Keishiro; Kobayashi, Yasushi

2012-01-01

In order to reduce uncertainties of long-term safety assessment for a High Level radioactive Waste (HLW) repository system, low alkaline cementitious grouting materials have been studied. The pH of the leachate from the grouting material is targeted to be below 11.0, since the degradation of the bentonite buffer and host rock is limited. The current work focused on the effects of pozzolanic reactions to reduce pH and the development of low alkaline cementitious injection materials in which super-micro ordinary Portland cement (SOPC) was partially replaced by silica fume (SF), micro silica (MS) and fly ash (FA). As it is important to realize how the grouting material will respond to a high injection pressure into the fracture, and in order to understand the penetrability of different low alkaline cement mixes and to observe their flow behavior through the fracture, injection tests were conducted by using a simulated model fracture of 2 m diameter made from parallel plates of acrylic acid resin and stainless steel. Experimental results of the basic properties for selecting suitable materials and that of injecting into a simulated fracture to assess the grouting performance are described

Effects of superglue fuming on materials characterization of zip-lock polyethylene bags for route forensic analyses

International Nuclear Information System (INIS)

Koester, C.J.; Grant, P.M.; Blankenship, J.F.

2013-01-01

Using cyanoacrylate or 'superglue' fuming to develop latent dermatoglyphic prints significantly altered the volatile and semivolatile compounds within the material of polyethylene zip-lock bags. Comparisons of SPME-GC/MS analyses of poly bags obtained before and after application of a glue fuming fingermark-developing technique resulted in markedly different material profiles of the bags. Not only were species added to the chemical composition of a bag, but other compounds that had been initially present were removed. These effects are particularly important for nuclear forensic investigations in the realm of route (pathway) analyses, and may also be of general interest to criminalistics laboratories that examine illicit drugs and their packaging. (author)

An Experimental Study on Mitigating Alkali Silica Reaction by Using Fly Ash (FA in Combination with Silica Fume and Expanded Perlite Powder (EPP

Directory of Open Access Journals (Sweden)

Isneini Mohd

2016-01-01

Full Text Available ASR suppression by FA, SF, EPP, FA in combination with SF and EPP were evaluated by both mortar bar and concrete prism test. Mortar bars were made based on JIS A 1146, meanwhile concrete prism bars were casted in accordance with Rilem AAR-3. Both specimens were stored in 40°C 100% R.H. controlled room. Mortar and concrete mixtures used reactive aggregate in pessimum proportion. The results indicated that FA in combination with SF and EPP showed smaller expansion compared to FA. The best of concrete mixtures in reducing expansion is combination of FA with SF (FA15SF10.

Development of a Zero-Cement Binder Using Slag, Fly Ash, and Rice Husk Ash with Chemical Activator

Directory of Open Access Journals (Sweden)

M. R. Karim

2015-01-01

Full Text Available The increasing demand and consumption of cement have necessitated the use of slag, fly ash, rice husk ash (RHA, and so forth as a supplement of cement in concrete construction. The aim of the study is to develop a zero-cement binder (Z-Cem using slag, fly ash, and RHA combined with chemical activator. NaOH, Ca(OH2, and KOH were used in varying weights and molar concentrations. Z-Cem was tested for its consistency, setting time, flow, compressive strength, XRD, SEM, and FTIR. The consistency and setting time of the Z-Cem paste increase with increasing RHA content. The Z-Cem mortar requires more superplasticizer to maintain a constant flow of 110±5% compared with OPC. The compressive strength of the Z-Cem mortar is significantly influenced by the amounts, types, and molar concentration of the activators. The Z-Cem mortar achieves a compressive strength of 42–44 MPa at 28 days with 5% NaOH or at 2.5 molar concentrations. The FTIR results reveal that molecules in the Z-Cem mortar have a silica-hydrate (Si-H bond with sodium or other inorganic metals (i.e., sodium/calcium-silica-hydrate-alumina gel. Therefore, Z-Cem could be developed using the aforementioned materials with the chemical activator.

Silica coated ionic liquid templated mesoporous silica nanoparticles ...

African Journals Online (AJOL)

A series of long chain pyridinium based ionic liquids 1-tetradecylpyridinium bromide, 1-hexadecylpyridinium bromide and 1-1-octadecylpyridinium bromide were used as templates to prepare silica coated mesoporous silica nanoparticles via condensation method under basic condition. The effects of alkyl chain length on ...

Quick monitoring of pozzolanic reactivity of waste ashes.

Science.gov (United States)

Sinthaworn, Suppachai; Nimityongskul, Pichai

2009-05-01

This article proposes a quick method of monitoring for pozzolanic reactivity of waste ashes by investigating the electrical conductivity of the suspension at an elevated temperature. This suspension is obtained by mixing tested pozzolan with an ordinary Portland cement (OPC) solution produced by mixing ordinary Portland cement with water. For comparison, silica fume, metakaolin, rice husk ash and river sand - whose pozzolanic reactivities range from reactive to inert - were used in the experimental investigation. The electrical conductivity of the suspension was continually recorded by using an electrical conductivity meter and stored by using a personal computer for a period of slightly over 1day. The indicative parameters that can be related to pozzolanic reactivity were discussed and analyzed in detail. It was found that it is possible to determine the pozzolanic reactivity of fly ash within 28h by using the proposed technique, as compared to 7 or 28 days for the determination of strength activity index according to ASTM. This technique would help concrete technologists to speedily investigate the quality of fly ash for use as a cement replacement in order to alleviate pollution caused by cement production and solve disposal problems of waste ashes.

Altered ion transport in normal human bronchial epithelial cells following exposure to chemically distinct metal welding fume particles.

Science.gov (United States)

Fedan, Jeffrey S; Thompson, Janet A; Meighan, Terence G; Zeidler-Erdely, Patti C; Antonini, James M

2017-07-01

Welding fume inhalation causes pulmonary toxicity, including susceptibility to infection. We hypothesized that airway epithelial ion transport is a target of fume toxicity, and investigated the effects of fume particulates from manual metal arc-stainless steel (MMA-SS) and gas metal arc-mild steel (GMA-MS) on ion transport in normal human bronchial epithelium (NHBE) cultured in air-interface. MMA-SS particles, more soluble than GMA-MS particles, contain Cr, Ni, Fe and Mn; GMA-MS particles contain Fe and Mn. MMA-SS or GMA-MS particles (0.0167-166.7μg/cm 2 ) were applied apically to NHBEs. After 18h transepithelial potential difference (V t ), resistance (R t ), and short circuit current (I sc ) were measured. Particle effects on Na + and Cl¯ channels and the Na + ,K + ,2Cl¯-cotransporter were evaluated using amiloride (apical), 5-nitro-2-[(3-phenylpropyl)amino]benzoic acid (NPPB, apical), and bumetanide (basolateral), respectively. MMA-SS (0.0167-16.7μg/cm 2 ) increased basal V t . Only 16.7μg/cm 2 GMA-MS increased basal V t significantly. MMA-SS or GMA-MS exposure potentiated I sc responses (decreases) to amiloride and bumetanide, while not affecting those to NPPB, GMA-MS to a lesser degree than MMA-SS. Variable effects on R t were observed in response to amiloride, and bumetanide. Generally, MMA-SS was more potent in altering responses to amiloride and bumetanide than GMA-MS. Hyperpolarization occurred in the absence of LDH release, but decreases in V t , R t , and I sc at higher fume particulate doses accompanied LDH release, to a greater extent for MMA-SS. Thus, Na + transport and Na + ,K + ,2Cl¯-cotransport are affected by fume exposure; MMA-MS is more potent than GMA-MS. Enhanced Na + absorption and decreased airway surface liquid could compromise defenses against infection. Published by Elsevier Inc.

FliO Regulation of FliP in the Formation of the Salmonella enterica Flagellum

Science.gov (United States)

Barker, Clive S.; Meshcheryakova, Irina V.; Kostyukova, Alla S.; Samatey, Fadel A.

2010-01-01

The type III secretion system of the Salmonella flagellum consists of 6 integral membrane proteins: FlhA, FlhB, FliO, FliP, FliQ, and FliR. However, in some other type III secretion systems, a homologue of FliO is apparently absent, suggesting it has a specialized role. Deleting the fliO gene from the chromosome of a motile strain of Salmonella resulted in a drastic decrease of motility. Incubation of the ΔfliO mutant strain in motility agar, gave rise to pseudorevertants containing extragenic bypass mutations in FliP at positions R143H or F190L. Using membrane topology prediction programs, and alkaline phosphatase or GFPuv chimeric protein fusions into the FliO protein, we demonstrated that FliO is bitopic with its N-terminus in the periplasm and C-terminus in the cytoplasm. Truncation analysis of FliO demonstrated that overexpression of FliO43–125 or FliO1–95 was able to rescue motility of the ΔfliO mutant. Further, residue leucine 91 in the cytoplasmic domain was identified to be important for function. Based on secondary structure prediction, the cytoplasmic domain, FliO43–125, should contain beta-structure and alpha-helices. FliO43–125-Ala was purified and studied using circular dichroism spectroscopy; however, this domain was disordered, and its structure was a mixture of beta-sheet and random coil. Coexpression of full-length FliO with FliP increased expression levels of FliP, but coexpression with the cytoplasmic domain of FliO did not enhance FliP expression levels. Overexpression of the cytoplasmic domain of FliO further rescued motility of strains deleted for the fliO gene expressing bypass mutations in FliP. These results suggest FliO maintains FliP stability through transmembrane domain interaction. The results also demonstrate that the cytoplasmic domain of FliO has functionality, and it presumably becomes structured while interacting with its binding partners. PMID:20941389

FliO regulation of FliP in the formation of the Salmonella enterica flagellum.