Long-Term Leak Tightness Of O-Ring Seals In The 9975 Shipping Package

International Nuclear Information System (INIS)

Hoffman, E.; Skidmore, E.; Daugherty, W.

2010-01-01

O-ring seals in the 9975 shipping package containment vessels are fabricated from a Viton GLT or GLT-S compound. Long-term testing of these O-rings has been performed to support service life predictions for packages used for long-term storage. Since the only criterion for O-ring performance is to maintain a leak-tight seal, leak testing is the primary indicator of service life. Fixtures have been aging at elevated temperatures to provide data for service life predictions. Limited leak test failures have been observed at the higher temperatures. This provides the opportunity for comparison to trends based on other O-ring properties, such as compression stress relaxation. Initial data suggest that the CSR data have some predictive value for a leak-tight service life, but other factors can complicate efforts to draw definitive conclusions.

Safety Analysis Report - Packages, 9965, 9968, 9972-9975 Packages

International Nuclear Information System (INIS)

Blanton, P.

2000-01-01

This Safety Analysis Report for Packaging (SARP) documents the analysis and testing performed on four type B Packages: the 9972, 9973, 9974, and 9975 packages. Because all four packages have similar designs with very similar performance characteristics, all of them are presented in a single SARP. The performance evaluation presented in this SARP documents the compliance of the 9975 package with the regulatory safety requirements. Evaluations of the 9972, 9973, and 9974 packages support that of the 9975. To avoid confusion arising from the inclusion of four packages in a single document, the text segregates the data for each package in such a way that the reader interested in only one package can progress from Chapter 1 through Chapter 9. The directory at the beginning of each chapter identifies each section that should be read for a given package. Sections marked ''all'' are generic to all packages

Equivalency relations for mixtures of nuclides in shipping casks 9972-9975

International Nuclear Information System (INIS)

Niemer, K.A.; Frost, R.L.; Williamson, T.G.

1994-01-01

Equivalence relations required to determine mass limits for mixtures of nuclides for the Safety Analysis Report for Packaging (SARP) of the Savannah River Site 9972, 9973, 9974, and 9975 shipping casks were calculated. The systems analyzed included aqueous spheres, homogeneous metal spheres, and metal ball-and-shell configurations, all surrounded by an effectively infinite stainless steel or water reflector. Comparison of the equivalence calculations with the rule-of-fractions showed conservative agreement for aqueous solutions, both conservative and non-conservative agreement for the metal homogenous sphere systems, and non-conservative agreement for the majority of metal ball-and-shell systems. Equivalence factors for the aqueous solutions and homogeneous metal spheres were calculated. The equivalence factors for the non-conservative metal homogeneous sphere systems were adjusted so that they were conservative. No equivalence factors were calculated for the ball-and-shell systems since the SARP assumes that only homogeneous or uniformly distributed material will be shipped in the 9972-9975 shipping casks, and an unnecessarily conservative critical mass may result if the ball-and-shell configurations are included

Safety Analysis Report - Packages, 9965, 9968, 9972-9975 Packages

International Nuclear Information System (INIS)

Van Alstine, M.N.

1999-01-01

This Safety Analysis Report for Packaging (SARP) documents the performance of the 9965 B, 9968 B, 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages in satisfying the regulatory safety requirements of the Code of Federal Regulations (CFR) 711 and the International Atomic Energy Agency (IAEA) Safety Series No. 6, Regulations for the Safe Transport of Radioactive Material, 1985 edition2. Results of the analysis and testing performed on the 9965 B, 9968 B, 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages are presented in this SARP, which was prepared in accordance with U.S. Department of energy (DOE) Order 5480.33 and in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guides 7.94 and 7.10.5

Safety analysis report - packages 9965, 9968, 9972-9975 packages

International Nuclear Information System (INIS)

Van Alstine, M.N.

1997-10-01

This Safety Analysis Report for Packaging (SARP) documents the performance of the 9965 B( ), 9968 B( ), 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages in satisfying the regulatory safety requirements of the Code of Federal Regulations (CFR) 10 CFR 71 and the International Atomic Energy Agency (IAEA) Safety Series No. 6, Regulations for the Safe Transport of Radioactive Material, 1985 edition. Results of the analysis and testing performed on the 9965 B(), 9968 B(), 9972 B(U), 9973 B(U), and 9975 B(U) packages are presented in this SARP, which was prepared in accordance with U.S. Department of Energy (DOE) Order 5480.3 and in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guides 7.9 and 7.10

FINAL REPORT FOR MOISTURE EFFECTS ON COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE

Energy Technology Data Exchange (ETDEWEB)

Stefek, T.; Daugherty, W.; Estochen, E.

2013-09-17

Compaction of lower layers in the fiberboard assembly has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and the behavior of the fiberboard during transport. In laboratory tests of cane fiberboard, higher moisture content has been shown to correspond to higher total compaction, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction compared to a static load. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted to acquire immediate and cumulative changes in geometric data for various moisture levels. Two sample sets have undergone a complete dynamic test regimen, one set for 27 weeks, and the second set for 47 weeks. The dynamic input, data acquisition, test effects on sample dynamic parameters, and results from this test program are summarized and compared to regulatory specifications for dynamic loading. Compaction of the bottom fiberboard layers due to the accumulation of moisture is one possible cause of an increase in the axial gap at the top of the package. The net compaction of the bottom layers will directly add to the axial gap. The moisture which caused this compaction migrated from the middle region of the fiberboard assembly (which is typically the hottest). This will cause the middle region to shrink axially, which will also contribute directly to the axial gap. Measurement of the axial gap provides a screening tool for identifying significant change in the fiberboard condition. The data in this report provide a basis to evaluate the impact of moisture and fiberboard compaction on 9975 package performance

Status Report - Cane Fiberboard Properties and Degradation Rates for Storage of the 9975 Shipping Package in KAMS

International Nuclear Information System (INIS)

Daugherty, W. L.

2013-01-01

the package is not as well characterized. While the outer drum does not provide an air-tight seal, it does greatly restrict the gain or loss of moisture in the fiberboard. Preliminary efforts have identified a relationship between the moisture content of fiberboard samples and the relative humidity of the surrounding air, but further work is needed in this area. Improvement in understanding this relationship might be realized with a change in the way humidity data are collected during field surveillances. It is recommended that the humidity be measured through a caplug hole before the package is removed from its storage location. The package would remain in thermal equilibrium, and anomalous humidity changes could be avoided. Further work should be performed to better define KAMS storage conditions and the environment within the 9975 shipping packages, and to identify appropriate limits for each property. This should be a joint effort by SRNL and NMM personnel. The results and model predictions presented in this report are applicable to 9975 packages with cane fiberboard overpack assemblies. A separate effort is underway to identify whether softwood fiberboard would behave similarly. In addition, the degradation models do not address the effects of non-conforming conditions such as the presence of excess moisture and mold, or beetle infestations

STATUS REPORT FOR MOISTURE EFFECTS ON COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE

Energy Technology Data Exchange (ETDEWEB)

Stefek, T.; Daugherty, W.; Estochen, E.

2011-06-23

Compaction of lower layers in the fiberboard overpack has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and the behavior of the fiberboard during transport. In laboratory tests, higher moisture content has been shown to correspond to higher total compaction of fiberboard material, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted over a period of six months to acquire immediate and cumulative changes in geometric data for various moisture levels. Currently, one sample set has undergone a complete dynamic test regimen, while testing of another set is still in-progress. The dynamic input, data acquisition, test effects on sample dynamic parameters, and interim results from this test program are summarized and compared to regulatory specifications for dynamic loading. This will provide a basis from which to evaluate the impact of moisture and fiberboard compaction on the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Documented Safety Analysis) at the Savannah River Site (SRS).

Technical Review Report for the Model 9975-96 Package Safety Analysis Report for Packaging (S-SARP-G-00003, Revision 0, January 2008)

International Nuclear Information System (INIS)

West, M.

2009-01-01

This Technical Review Report (TRR) documents the review, performed by the Lawrence Livermore National Laboratory (LLNL) Staff, at the request of the U.S. Department of Energy (DOE), on the Safety Analysis Report for Packaging, Model 9975, Revision 0, dated January 2008 (S-SARP-G-00003, the SARP). The review includes an evaluation of the SARP, with respect to the requirements specified in 10 CFR 71, and in International Atomic Energy Agency (IAEA) Safety Standards Series No. TS-R-1. The Model 9975-96 Package is a 35-gallon drum package design that has evolved from a family of packages designed by DOE contractors at the Savannah River Site. Earlier package designs, i.e., the Model 9965, the Model 9966, the Model 9967, and the Model 9968 Packagings, were originally designed and certified in the early 1980s. In the 1990s, updated package designs that incorporated design features consistent with the then newer safety requirements were proposed. The updated package designs at the time were the Model 9972, the Model 9973, the Model 9974, and the Model 9975 Packagings, respectively. The Model 9975 Package was certified by the Packaging Certification Program, under the Office of Safety Management and Operations. The safety analysis of the Model 9975-85 Packaging is documented in the Safety Analysis Report for Packaging, Model 9975, B(M)F-85, Revision 0, dated December 2003. The Model 9975-85 Package is certified by DOE Certificate of Compliance (CoC) package identification number, USA/9975/B(M)F-85, for the transportation of Type B quantities of uranium metal/oxide, 238 Pu heat sources, plutonium/uranium metals, plutonium/uranium oxides, plutonium composites, plutonium/tantalum composites, 238 Pu oxide/beryllium metal.

Thermal Analysis Of A 9975 Package In A Facility Fire Accident

International Nuclear Information System (INIS)

Gupta, N.

2011-01-01

Surplus plutonium bearing materials in the U.S. Department of Energy (DOE) complex are stored in the 3013 containers that are designed to meet the requirements of the DOE standard DOE-STD-3013. The 3013 containers are in turn packaged inside 9975 packages that are designed to meet the NRC 10 CFR Part 71 regulatory requirements for transporting the Type B fissile materials across the DOE complex. The design requirements for the hypothetical accident conditions (HAC) involving a fire are given in 10 CFR 71.73. The 9975 packages are stored at the DOE Savannah River Site in the K-Area Material Storage (KAMS) facility for long term of up to 50 years. The design requirements for safe storage in KAMS facility containing multiple sources of combustible materials are far more challenging than the HAC requirements in 10 CFR 71.73. While the 10 CFR 71.73 postulates an HAC fire of 1475 F and 30 minutes duration, the facility fire calls for a fire of 1500 F and 86 duration. This paper describes a methodology and the analysis results that meet the design limits of the 9975 component and demonstrate the robustness of the 9975 package.

Nuclear Criticality Safety Evaluation of the 9965, 9968, 9972, 9973, 9974, and 9975 Shipping Casks

International Nuclear Information System (INIS)

Frost, R.L.

1999-01-01

A Nuclear Criticality Safety Evaluation (NCSE) has been performed for the 9965, 9968, 9972, 9973, 9974, and 9975 SRS-designed shipping casks. This was done in support of the recertification effort for the 9965 and 9968, and the certification of the newly designed 9972-9975 series. The analysis supports the use of these packages as Fissile Class I for shipment of fissionable material from the SRS FB-Line, HB-Line, and from Lawrence Livermore national Laboratory. six different types of material were analyzed with varying Isotopic composition, of both oxide and metallic form. The mass limits required to support the fissile Class I rating for each of the envelopes are given in the Table below. These mass limits apply if DOE approves an exception as described in 10 CFR 71.55(c), such that water leakage into the primary containment vessel does not need to be considered in the criticality analysis. If this exception is not granted, the mass limits are lower than those shown below. this issue is discussed in detail in sections 5 and 6 of the report.One finding from this work is important enough to highlight in the abstract. The fire tests performed for this family of shipping casks indicates only minimal charring of the Celotex thermal insulation. Analysis of the casks with no Celotex insulation (assuming it has all burned away), results in values of k-eff that exceed 1.0. Therefore, the Celotex insulation must remain intact in order to guarantee sub criticality of the 9972-9975 family of shipping casks

WHITE PAPER: DEMONSTRATION OF EQUIVALENCY OF CANE AND SOFTWOOD BASED CELOTEX FOR 9975 PACKAGING

International Nuclear Information System (INIS)

Varble, J

2007-01-01

Cane-based Celotex(trademark) has been used extensively in various DOE packages as a thermal insulator and impact absorber. Cane-based Celotex(trademark) for the 9975 was manufactured by Knight-Celotex Fiberboard at their Marrero Plant in Louisiana. However, Knight-Celotex Fiberboard shut down their Marrero Plant in early 2007 due to impacts from hurricane Katrina and other economic factors. Therefore, cane-based Celotex(trademark) is no longer available for use in the manufacture of new 9975 packages. Knight-Celotex Fiberboard has Celotex(trademark) manufacturing plants in Danville, VA and Sunbury, PA that use softwood and hardwood, respectively, as a raw material in the manufacturing of Celotex(trademark). The purpose of this White Paper is to demonstrate that softwood-based Celotex(trademark) from the Knight-Celotex Danville Plant has performance equivalent to cane-based Celotex(trademark) from the Knight-Celotex Marrero Plant for transportation in a 9975 package

Equivalence relations for the 9972-9975 SARP

International Nuclear Information System (INIS)

Niemer, K.A.; Frost, R.L.

1994-10-01

Equivalence relations required to determine mass limits for mixtures of nuclides for the Safety Analysis Report for Packaging (SARP) of the Savannah River Site 9972, 9973, 9974, and 9975 shipping casks were calculated. The systems analyzed included aqueous spheres, homogeneous metal spheres, and metal ball-and-shell configurations, all surrounded by an effectively infinite stainless steel or water reflector. Comparison of the equivalence calculations with the rule-of-fractions showed conservative agreement for aqueous solutions, both conservative and non-conservative agreement for the metal homogeneous sphere systems, and non-conservative agreement for the majority of metal ball-and-shell systems. Equivalence factors for the aqueous solutions and homogeneous metal spheres were calculated. The equivalence factors for the non-conservative metal homogeneous sphere systems were adjusted so that they were conservative. No equivalence factors were calculated for the ball-and-shell systems since the -SARP assumes that only homogeneous or uniformly distributed material will be shipped in the 9972-9975 shipping casks, and an unnecessarily conservative critical mass may result if the ball-and-shell configurations are included

Model 9975 Life Extension Test Package 3 - Interim Report - January 2017

Energy Technology Data Exchange (ETDEWEB)

Daugherty, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-01-31

Life extension package LE3 (9975-03203) has been instrumented and subjected to an elevated temperature environment for approximately 8 years. During this time, the cane fiberboard has been maintained at a maximum temperature of ~160 - 165 °F, which was established by a combination of internal (19 watts) and external heat sources. Several tests and parameters were used to characterize the package components. Results from these tests generally indicate agreement between this full-scale shipping package and small-scale laboratory tests on fiberboard samples, including the degradation models based on the laboratory tests. These areas of agreement include the rate of change of fiberboard weight, dimensions and density, and change in fiberboard thermal conductivity. Corrosion of the lead shield occurred at a high rate during the first several weeks of aging, but dropped significantly after most of the moisture in the fiberboard migrated away from the lead shield. Dimensional measurements of the lead shield indicate that no significant creep deformation has occurred. This is consistent with literature data that predict a very small creep deformation for the time at temperature experienced by this package. The SCV O-rings were verified to remain leak-tight after ~5 years aging at an average temperature of ~170 °F. This package provides an example of the extent to which moisture within a typical fiberboard assembly can redistribute in the presence of a temperature gradient such as might be created by a 19 watt internal heat load. The majority of water within the fiberboard migrated to the bottom layers of fiberboard, with approximately 2 kg of water (2 liters) eventually escaping from the package. Two conditions have developed that are not consistent with package certification requirements. The axial gap at the top of the package increased to a maximum value of 1.549 inches, exceeding the 1 inch criterion. In addition, staining and/or corrosion have formed in a few spots

DETECTION OF DRUGSTORE BEETLES IN 9975 PACKAGES USING ACOUSTIC EMISSIONS

Energy Technology Data Exchange (ETDEWEB)

Shull, D.

2013-03-04

This report documents the initial feasibility tests performed using a commercial acoustic emission instrument for the purpose of detecting beetles in Department of Energy 9975 shipping packages. The device selected for this testing was a commercial handheld instrument and probe developed for the detection of termites, weevils, beetles and other insect infestations in wooden structures, trees, plants and soil. The results of two rounds of testing are presented. The first tests were performed by the vendor using only the hand-held instrument’s indications and real-time operator analysis of the audio signal content. The second tests included hands-free positioning of the instrument probe and post-collection analysis of the recorded audio signal content including audio background comparisons. The test results indicate that the system is promising for detecting the presence of drugstore beetles, however, additional work would be needed to improve the ease of detection and to automate the signal processing to eliminate the need for human interpretation. Mechanisms for hands-free positioning of the probe and audio background discrimination are also necessary for reliable detection and to reduce potential operator dose in radiation environments.

Digital Radiography of a Drop Tested 9975 Radioactive Materials Packaging

International Nuclear Information System (INIS)

Blanton, P.S.

2001-01-01

This paper discusses the use of radiography as a tool for evaluating damage to radioactive material packaging subjected to regulatory accident conditions. The Code of Federal Regulations, 10 CFR 71, presents the performance based requirements that must be used in the development (design, fabrication and testing) of a radioactive material packaging. The use of various non-destructive examination techniques in the fabrication of packages is common. One such technique is the use of conventional radiography in the examination of welds. Radiography is conventional in the sense that images are caught one at a time on film stock. Most recently, digital radiography has been used to characterize internal damage to a package subjected to the 30-foot hypothetical accident conditions (HAC) drop. Digital radiography allows for real time evaluation of the item being inspected. This paper presents a summary discussion of the digital radiographic technique and an example of radiographic results of a 9975 package following the HAC 30-foot drop

Sixth Status Report: Testing of Aged Softwood Fiberboard Material for the 9975 Shipping Package

Energy Technology Data Exchange (ETDEWEB)

Daugherty, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-03-31

Samples have been prepared from several 9975 lower fiberboard subassemblies fabricated from softwood fiberboard. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples, with a few differences. Some softwood fiberboard properties tend to degrade faster in some environments, while some cane fiberboard properties degrade faster in the two most aggressive environments. As a result, it is premature to assume both materials will age at the same rates, and the preliminary aging models developed for cane fiberboard might not apply to softwood fiberboard. However, it is expected that both cane and softwood fiberboard assemblies will perform satisfactorily in conforming packages stored in a typical KAC storage environment for up to 15 years. Samples from an additional 3 softwood fiberboard assemblies have begun aging during the past year to provide information on the variability of softwood fiberboard behavior. Aging and testing of softwood fiberboard will continue and additional data will be collected to support development of an aging model specific to softwood fiberboard.

SRTC criticality safety technical review: Phase 1 criticality analysis for the 9972-9975 family of shipping casks: (SRT-CMA-940003)

International Nuclear Information System (INIS)

Rathbun, R.

1994-01-01

Review of SRT-CMA-940003, ''Phase I Criticality Analysis For The 9972-9975 Family Of Shipping Casks (U). (SRT-CMA-940003).'' January 22, 1994, has been performed by the SRTC Applied Physics Group. The NCSE is a criticality assessment of the 9972-9975 family of shipping casks. This work is a follow-on of a previous criticality safety evaluation, with the differences between this and the previous evaluation are that now wall tolerances are modeled and more sophisticated analytical methods are applied. The NCSE under review concludes that, with one exception, the previously specified plutonium and uranium mass limits for 9972-9975 family of shipping casks do ensure that WSRC Nuclear Criticality Safety Manual requirements (ref. 1) are satisfied. The one exception is that the plutonium mass limit for the 9974 cask had to be reduced from 4.4 to 4.3 kg. In contrast, the 7.5 kg uranium mass limit for the 9974 cask was raised to 14.5 kg, making the uranium mass identical for all casks in this family. This technical review consisted of an independent check of the methods and models employed, application of ANSI/ANS 8.1 and 8.15, and verification of WSRC Nuclear Criticality Safety Manual procedures

Model 9975 Life Extension Package 1 - Final Report

International Nuclear Information System (INIS)

Daugherty, W.

2011-01-01

Life extension package LE1 (9975-03382) was instrumented and subjected to a temperature/humidity environment that bounds KAMS package storage conditions for 92 weeks. During this time, the maximum fiberboard temperature was ∼180 F, and was established by a combination of internal heat (12 watts) and external heat (∼142 F). The relative humidity external to the package was maintained at 80 %RH. This package was removed from test in November 2010 after several degraded conditions were observed during a periodic examination. These conditions included degraded fiberboard (easily broken, bottom layer stuck to the drum), corrosion of the drum, and separation of the air shield from the upper fiberboard assembly. Several tests and parameters were used to characterize the package components. Results from these tests generally indicate agreement between this full-scale shipping package and small-scale laboratory tests on fiberboard and O-ring samples. These areas of agreement include the rate of fiberboard weight loss, change in fiberboard thermal conductivity, fiberboard compression strength, and O-ring compression set. In addition, this package provides an example of the extent to which moisture within the fiberboard can redistribute in the presence of a temperature gradient such as might be created by a 12 watt internal heat load. Much of the moisture near the fiberboard ID surface migrated towards the OD surface, but there was not a significant axial moisture gradient during most of the test duration. Only during the last inspection period (i.e. after 92 weeks exposure during the second phase) did enough moisture migrate to the bottom fiberboard layers to cause saturation. A side effect of moisture migration is the leaching of soluble compounds from the fiberboard. In particular, the corrosion observed on the drum appears related primarily to the leaching and concentration of chlorides. In most locations, this attack appears to be general corrosion, with shallow

9978 AND 9975 TYPE B PACKAGING INTERNAL DATA COLLECTION FEASIBILITY TESTING

Energy Technology Data Exchange (ETDEWEB)

Fogle, R.

2012-05-07

The objective of this report is to document the findings from a series of proof-of-concept tests performed by Savannah River National Laboratory (SRNL) R and D Engineering, for the DOE Packaging Certification Program to determine if a viable radio link could be established from within the stainless steel confines of several drum-style DOE certified Type B radioactive materials packagings. Two in-hand, off-the-shelf radio systems were tested. The first system was a Wi-Fi Librestream Onsight{trademark} camera with a Fortress ES820 Access Point and the second was the On-Ramp Wireless Ultra-Link Processing{trademark} (ULP) radio system. These radio systems were tested within the Model 9975 and 9978 Type B packagings at the SRNL. This report documents the test methods and results. A path forward will also be recommended.

Thermal Analysis Of 3013/9975 Configuration

International Nuclear Information System (INIS)

Gupta, N.

2009-01-01

The 3013 containers are designed in accordance with the DOE-STD-3013-2004 and are qualified to store plutonium (Pu) bearing materials for 50 years. The U.S. Department of Energy (DOE) certified Model 9975 shipping package is used to transport the 3013 containers to the K-Area Material Storage (KAMS) facility at the Savannah River Site (SRS) and to store the containers until the plutonium can be properly dispositioned. Detailed thermal analyses to support the storage in the KAMS facility are given in References 2, 3, and 4. The analyses in this paper serve to provide non-accident condition, non-bounding, specific 3013 container temperatures for use in the surveillance activities. This paper presents a methodology where critical component temperatures are estimated using numerical methods over a range of package and storage parameters. The analyses include factors such as ambient storage temperature and the content weight, density, heat generation rate, and fill height, that may impact the thermal response of the packages. Statistical methods are used to develop algebraic equations for ease of computations to cover the factor space. All computations were performed in BTU-FT-Hr- o F units.

INVESTIGATION OF THE PRESENCE OF DRUGSTORE BEETLES WITHIN CELOTEX ASSEMBLIES IN RADIOACTIVE MATERIAL PACKAGINGS

Energy Technology Data Exchange (ETDEWEB)

Loftin, B; Glenn Abramczyk, G

2008-06-04

During normal operations at the Department of Energy's Hanford Site in Hanford, WA, drugstore beetles, (Stegobium paniceum (L.) Coleoptera: Anobiidae), were found within the fiberboard subassemblies of two 9975 Shipping Packages. Initial indications were that the beetles were feeding on the Celotex{trademark} assemblies within the package. Celotex{trademark} fiberboard is used in numerous radioactive material packages serving as both a thermal insulator and an impact absorber for both normal conditions of transport and hypothetical accident conditions. The Department of Energy's Packaging Certification Program (EM-63) directed a thorough investigation to determine if the drugstore beetles were causing damage that would be detrimental to the safety performance of the Celotex{trademark}. The Savannah River National Laboratory is conducting the investigation with entomological expertise provided by Clemson University. The two empty 9975 shipping packages were transferred to the Savannah River National Laboratory in the fall of 2007. This paper will provide details and results of the ongoing investigation.

3013/9975 Surveillance Program Interim Summary Report

Energy Technology Data Exchange (ETDEWEB)

Dunn, K.; Hackney, B.; McClard, J.

2011-06-22

The K-Area Materials Storage (KAMS) Documented Safety Analysis (DSA) requires a surveillance program to monitor the safety performance of 3013 containers and 9975 shipping packages stored in KAMS. The SRS surveillance program [Reference 1] outlines activities for field surveillance and laboratory tests that demonstrate the packages meet the functional performance requirements described in the DSA. The SRS program also supports the complexwide Integrated Surveillance Program (ISP) [Reference 2] for 3013 containers. The purpose of this report is to provide a summary of the SRS portion of the surveillance program activities through fiscal year 2010 (FY10) and formally communicate the interpretation of these results by the Surveillance Program Authority (SPA). Surveillance for the initial 3013 container random sampling of the Innocuous bin and the Pressure bin has been completed and there has been no indication of corrosion or significant pressurization. The maximum pressure observed was less than 50 psig, which is well below the design pressure of 699 psig for the 3013 container [Reference 3]. The data collected during surveillance of these bins has been evaluated by the Materials Identification and Surveillance (MIS) Working Group and no additional surveillance is necessary for these bins at least through FY13. A decision will be made whether additional surveillance of these bins is needed during future years of storage and as additional containers are generated. Based on the data collected to date, the SPA concludes that 3013 containers in these bins can continue to be safely stored in KAMS. This year, 13 destructive examinations (DE) were performed on random samples from the Pressure & Corrosion bin. To date, DE has been completed for approximately 30% of the random samples from the Pressure & Corrosion bin. In addition, DE has been performed on 6 engineering judgment (EJ) containers, for a total of 17 to date. This includes one container that exceeded the 3013

Analysis to evaluate predictors of fiberboard aging to guide surveillance sampling for the 9975 life extension program

Energy Technology Data Exchange (ETDEWEB)

Kelly, Elizabeth J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Daugherty, William L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hackney, Elizabeth R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-05-09

During surveillance of the 9975 shipping package at the Savannah River Site K-Area Complex, several package dimensions are recorded. The analysis described in this report shows that, based on the current data analysis, two of these measurements, Upper Assembly Outer Diameter (UAOD) and Upper Assembly Inside Height (UAIH), do not have statistically significant aging trends regardless of wattage levels. In contrast, this analysis indicates that the measurement of Air Shield Gap (ASGap) does show a significant increase with age. It appears that the increase is greater for high wattage containers, but this result is dominated by two measurements from high-wattage containers. For all three indicators, additional high-wattage, older containers need to be examined before any definitive conclusions can be reached. In addition, the current analysis indicates that ASGap measurements for low and medium wattage containers are increasing slowly over time. To reduce uncertainties and better capture the aging trend for these containers, additional low and medium wattage older containers should also be examined. Based on this analysis, surveillance guidance is to augment surveillance containers resulting from 3013 surveillance with 9975-focused sampling that targets older, high wattage containers and also includes some older, low and medium wattage containers. This focused sampling began in 2015 and will continue in 2016. The UAOD, UAIH and ASGap data are highly variable. It is possible that additional factors such as seasonal variation and packaging site location might reduce variability and be useful for focusing surveillance and predicting aging.

3013/9975 Surveillance Program Interim Summary Report

International Nuclear Information System (INIS)

Dunn, K.; Hackney, B.; McClard, J.

2011-01-01

The K-Area Materials Storage (KAMS) Documented Safety Analysis (DSA) requires a surveillance program to monitor the safety performance of 3013 containers and 9975 shipping packages stored in KAMS. The SRS surveillance program (Reference 1) outlines activities for field surveillance and laboratory tests that demonstrate the packages meet the functional performance requirements described in the DSA. The SRS program also supports the complexwide Integrated Surveillance Program (ISP) (Reference 2) for 3013 containers. The purpose of this report is to provide a summary of the SRS portion of the surveillance program activities through fiscal year 2010 (FY10) and formally communicate the interpretation of these results by the Surveillance Program Authority (SPA). Surveillance for the initial 3013 container random sampling of the Innocuous bin and the Pressure bin has been completed and there has been no indication of corrosion or significant pressurization. The maximum pressure observed was less than 50 psig, which is well below the design pressure of 699 psig for the 3013 container (Reference 3). The data collected during surveillance of these bins has been evaluated by the Materials Identification and Surveillance (MIS) Working Group and no additional surveillance is necessary for these bins at least through FY13. A decision will be made whether additional surveillance of these bins is needed during future years of storage and as additional containers are generated. Based on the data collected to date, the SPA concludes that 3013 containers in these bins can continue to be safely stored in KAMS. This year, 13 destructive examinations (DE) were performed on random samples from the Pressure and Corrosion bin. To date, DE has been completed for approximately 30% of the random samples from the Pressure and Corrosion bin. In addition, DE has been performed on 6 engineering judgment (EJ) containers, for a total of 17 to date. This includes one container that exceeded the 3013

Computerized waste-accountability shipping and packaging system

International Nuclear Information System (INIS)

Jackson, J.A.; Baston, M. Jr.; DeVer, E.A.

1981-01-01

The Waste Accountability, Shipping and Packaging System (WASP) is a real-time computerized system designed and implemented by Mound Facility to meet the stringent packaging and reporting requirements of radioactive waste being shipped to burial sites. The system stores packaging data and inspection results for each unit and prepares all necessary documents at the time of shipment. Shipping data specific for each burial site are automatically prepared on magnetic tape for transmission to the computing center at that site. WASP has enabled Mound Facility to effectively meet the requirements of the burial sites, diminishing the possibility of being rejected from a site because of noncompliance

Inspection, testing, and operating requiremens for the packaging and shipping of uranium trioxide in 55-gallon Department of Transportation (DOT) Specification 6M shipping packagings

International Nuclear Information System (INIS)

Toomer, D.V.

1991-06-01

This document identifies the inspection, testing and operating requirements for the packaging, loading, and shipping of uranium trioxide (UO 3 ) in 55-gallon DOT Specification 6M shipping packagings from the Idaho Chemical Processing Plant (ICPP). Compliance with this document assures established controls for the purchasing, packaging, loading, and shipping of DOT Specification 6M shipping packagings are maintained in strict accordance with applicable Code of Federal Regulations (CFRs) and Department of Energy (DOE) Orders. 7 refs., 3 figs., 1 tab

Extension of ship accident analysis to multiple-package shipments

International Nuclear Information System (INIS)

Mills, G.S.; Neuhauser, K.S.

1997-11-01

Severe ship accidents and the probability of radioactive material release from spent reactor fuel casks were investigated previously. Other forms of RAM, e.g., plutonium oxide powder, may be shipped in large numbers of packagings rather than in one to a few casks. These smaller, more numerous packagings are typically placed in ISO containers for ease of handling, and several ISO containers may be placed in one of several holds of a cargo ship. In such cases, the size of a radioactive release resulting from a severe collision with another ship is determined not by the likelihood of compromising a single, robust package but by the probability that a certain fraction of 10's or 100's of individual packagings is compromised. The previous analysis involved a statistical estimation of the frequency of accidents which would result in damage to a cask located in one of seven cargo holds in a collision with another ship. The results were obtained in the form of probabilities (frequencies) of accidents of increasing severity and of release fractions for each level of severity. This paper describes an extension of the same general method in which the multiple packages are assumed to be compacted by an intruding ship's bow until there is no free space in the hold. At such a point, the remaining energy of the colliding ship is assumed to be dissipated by progressively crushing the RAM packagings and the probability of a particular fraction of package failures is estimated by adaptation of the statistical method used previously. The parameters of a common, well characterized packaging, the 6M with 2R inner containment vessel, were employed as an illustrative example of this analysis method. However, the method is readily applicable to other packagings for which crush strengths have been measured or can be estimated with satisfactory confidence

Extension of ship accident analysis to multiple-package shipments

International Nuclear Information System (INIS)

Mills, G.S.; Neuhauser, K.S.

1998-01-01

Severe ship accidents and the probability of radioactive material release from spent reactor fuel casks were investigated previously (Spring, 1995). Other forms of RAM, e.g., plutonium oxide powder, may be shipped in large numbers of packagings rather than in one to a few casks. These smaller, more numerous packagings are typically placed in ISO containers for ease of handling, and several ISO containers may be placed in one of several holds of a cargo ship. In such cases, the size of a radioactive release resulting from a severe collision with another ship is determined not by the likelihood of compromising a single, robust package but by the probability that a certain fraction of 10's or 100's of individual packagings is compromised. The previous analysis (Spring, 1995) involved a statistical estimation of the frequency of accidents which would result in damage to a cask located in one of seven cargo holds in a collision with another ship. The results were obtained in the form of probabilities (frequencies) of accidents of increasing severity and of release fractions for each level of severity. This paper describes an extension of the same general method in which the multiple packages are assumed to be compacted by an intruding ship's bow until there is no free space in the hold. At such a point, the remaining energy of the colliding ship is assumed to be dissipated by progressively crushing the RAM packagings and the probability of a particular fraction of package failures is estimated by adaptation of the statistical method used previously. The parameters of a common, well-characterized packaging, the 6M with 2R inner containment vessel, were employed as an illustrative example of this analysis method. However, the method is readily applicable to other packagings for which crush strengths have been measured or can be estimated with satisfactory confidence. (authors)

Containment analysis of the 9975 transportation package with multiple barriers

International Nuclear Information System (INIS)

Vinson, D.W.

2000-01-01

A containment analysis has been performed for the scenario of non-routine transfer of a damaged 9975 package containing plutonium metal from K-area monitored storage to F-area on the Savannah River Site. A multiple barrier system with each barrier having a defined leakage rate of less than 1times10 -3 cm 3 /sec of air at Standard Temperature and Pressure was analyzed to determine the number of barriers needed to transport the package under normal transportation conditions to meet transportation requirements for containment. The barrier system was analyzed parametrically to achieve a composite system that met the federal requirements for the maximum permissible release rate given in Title 10 of the Code of Federal Regulations, Part 71. The multiple barrier system acts to retard the release of radioactivity. That is, a build-up in the radioactivity release rate occurs with time. For example, a system with three barriers (e.g., sealed plastic barrier) with a total free volume of 4,500 cm 3 could be transported for a total time of up to approximately 10 days with a release rate within the permissible rate. Additional number of barriers, or volume of the barriers, or both, would extend to this period of time. For example, a system with seven barriers with a total free volume of 4,500 cm 3 could be transported for up to 100 days. Plastic bags are one type of barrier used in movement of radioactive materials and capable of achieving a leak rate of 1times10 -3 cm 3 /sec of air at STP. Low-density polyethylene bags can withstand high temperature (up to 180 degrees C); a barrier thickness of 10 mils should be suitable for the barrier system. Additional requirements for barriers are listed in Section 4.2 of this report. Container testing per ANSI N14.5 is required to demonstrate leak rates for the individual barriers of less than 1times10 -3 cm 3 /sec

12 CFR 997.5 - Termination of the obligation.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Termination of the obligation. 997.5 Section 997.5 Banks and Banking FEDERAL HOUSING FINANCE BOARD NON-BANK SYSTEM ENTITIES RESOLUTION FUNDING CORPORATION OBLIGATIONS OF THE BANKS § 997.5 Termination of the obligation. (a) Generally. The Banks...

Work Package 2 Report - Cyber resilience for the shipping industry

DEFF Research Database (Denmark)

Sahay, Rishikesh; Sepúlveda Estay, Daniel Alberto

2018-01-01

This report describes the current state of the research performed as a part of the CyberShip project for its Work Package 2. This work package aims at defining a CyberShip model and KPIs for cyber resilience. This is a project funded by the Danish Maritime Fund (DMF) with the objective of proposing...

Safety analysis report on Model UC-609 shipping package

International Nuclear Information System (INIS)

Sandberg, R.R.

1977-08-01

This Safety Analysis Report for Packaging demonstrates that model UC-609 shipping package can safely transport tritium in any of its forms. The package and its contents are described. The package when subjected to the transport conditions specified in the Code of Federal Regulations, Title 10, Part 71 is evaluated. Finally, compliance with these regulations is discussed

LEVERAGING AGING MATERIALS DATA TO SUPPORT EXTENSION OF TRANSPORTATION SHIPPING PACKAGES SERVICE LIFE

Energy Technology Data Exchange (ETDEWEB)

Dunn, K. [Savannah River National Laboratory; Bellamy, S. [Savannah River National Laboratory; Daugherty, W. [Savannah River National Laboratory; Sindelar, R. [Savannah River National Laboratory; Skidmore, E. [Savannah River National Laboratory

2013-08-18

Nuclear material inventories are increasingly being transferred to interim storage locations where they may reside for extended periods of time. Use of a shipping package to store nuclear materials after the transfer has become more common for a variety of reasons. Shipping packages are robust and have a qualified pedigree for performance in normal operation and accident conditions but are only certified over an approved transportation window. The continued use of shipping packages to contain nuclear material during interim storage will result in reduced overall costs and reduced exposure to workers. However, the shipping package materials of construction must maintain integrity as specified by the safety basis of the storage facility throughout the storage period, which is typically well beyond the certified transportation window. In many ways, the certification processes required for interim storage of nuclear materials in shipping packages is similar to life extension programs required for dry cask storage systems for commercial nuclear fuels. The storage of spent nuclear fuel in dry cask storage systems is federally-regulated, and over 1500 individual dry casks have been in successful service up to 20 years in the US. The uncertainty in final disposition will likely require extended storage of this fuel well beyond initial license periods and perhaps multiple re-licenses may be needed. Thus, both the shipping packages and the dry cask storage systems require materials integrity assessments and assurance of continued satisfactory materials performance over times not considered in the original evaluation processes. Test programs for the shipping packages have been established to obtain aging data on materials of construction to demonstrate continued system integrity. The collective data may be coupled with similar data for the dry cask storage systems and used to support extending the service life of shipping packages in both transportation and storage.

46 CFR 153.976 - Transfer of packaged cargo or ship's stores.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Transfer of packaged cargo or ship's stores. 153.976 Section 153.976 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Operations Cargo Transfer Procedures § 153.976 Transfer of...

Testing and evaluation of used UF6 shipping packages

International Nuclear Information System (INIS)

Barlow, C.R.; Ziehlke, K.T.; Pryor, W.A.; Housholder, W.R.

1986-01-01

Damage to shipping packages and their components, whether due to normal environmental exposure or because of unforeseen accidents, requires occasional reevaluation and requalification to assure the suitability of the packages for continued service. Pressure tests have been conducted on used 30B cylinders that were involved in a warehouse fire to assess the possible damaging effects of the exposure. Deteriorated and mechanically damaged overpacks which had absorbed large quantities of water in service were subjected to drying tests, foam properties were evaluated, and a rehabilitation procedure was developed to allow return of such packages to service. Protective shipping packages show deterioration with extended service, principally structural damage from rough handling and rust damage from exposure to weather and from storage practices which may promote absorption of water by the insulating foam. The structural and thermal properties of the phenolic foam insulation from used shipping packages were found to be not adversely affected by absorbed water, and they were not degraded by the drying process. In order to slow or avoid continuing rust damage in renovated packages, however, a process was developed for drying the foam in commercial facilities prior to restoration work on used or damaged containers. Two 2-1/2-ton steel transport cylinders, type 30B, were involved in a warehouse fire where portions of the cylinders were estimated to have reached a temperature of 1600 0 F. The cylinders were empty at the time of the fire and thus were not in the protective packages in which full product cylinders are handled while in transit. Hydrostatic burst tests showed that the integrity of the cylinders was not degraded by the fire exposure. They withstood test pressures in excess of 10 times the design pressure, and showed a volume expansion of 30% above the original capacity before rupturing in a completely ductile fashion

Safety analysis report: packages. DOT specification 7A - Type A container Mark 15 sludge shipping package

International Nuclear Information System (INIS)

Zeh, C.W.

1985-03-01

Sludge or filter cake containing 1.1 wt % 235 U enriched uranium from Mark 15 fabrication will be packaged in 55-gallon containers and shipped from SRP to NLO, Fernald, Ohio for recovery of product. About 7 Metric Tons (MT) of filter cake will be produced from fabricating Mark 15 slugs each reactor charge. Packaged shipments of this material, consigned as exclusive use, will be shipped to NLO in Department of Transportation (DOT) Specification 7A - Type A packages under a DOE Certificate of Compliance for Fissile Class III shipments. ''Type A packaging'' is designed to retain containment and shielding integrity under normal conditions of transport. This report documents compliance of the package design, construction methods, material and test performance with DOT Specification 7A. This DOT 7A Type A package contains a carbon steel outer container which is a 0.060-in.-thick 55-gal, galvanized drum equipped with a gasketed closure. The outer container encloses a 0.090-in.-thick, open head, polyethylene liner with lid

Eleventh interim status report: Model 9975 O-Ring fixture long-term leak performance

Energy Technology Data Exchange (ETDEWEB)

Daugherty, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-08-01

A series of experiments to monitor the aging performance of Viton® GLT O-rings used in the Model 9975 package has been ongoing since 2004 at the Savannah River National Laboratory. One approach has been to periodically evaluate the leak performance of O-rings being aged in mock-up 9975 Primary Containment Vessels (PCVs) at elevated temperature. Other methods such as compression-stress relaxation (CSR) tests and field surveillance are also on-going to evaluate O-ring behavior. Seventy tests using PCV mock-ups were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determine if they continue to meet the leak-tightness criterion defined in ANSI standard N14.5-97. Due to material substitution, fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF.

The effect of cargo on the crush loading of RAM transportation packages in ship collisions

International Nuclear Information System (INIS)

Radloff, H.D.; Ammerman, D.J.

1998-03-01

Recent intercontinental radioactive material shipping campaigns have focused public and regulatory attention on the safety of transport of this material by ocean-going vessels. One major concern is the response of the vessel and onboard radioactive material (RAM) packages during a severe ship-to-ship collision. These collisions occur at velocities less than the velocity obtained in the Type B package regulatory impact event and the bow of the striking ship is less rigid than the unyielding target used in those tests (Ammerman and Daidola, 1996). This implies that ship impact is not a credible scenario for damaging the radioactive material packages during ship collisions. It is possible, however, for these collisions to generate significant amounts of crush force by the bow of the impacting ship overrunning the package. It is the aim of this paper to determine an upper bound on the magnitude of this crush force taking into account the strength of the radioactive material carrying vessel and any other cargo that may be stowed in the same hold as the radioactive material

Design and criticality considerations for 9977 and 9978 shipping packages

International Nuclear Information System (INIS)

Reed, R.; Biswas, D.; Abramczyk, G.

2009-01-01

Savannah River National Laboratory (SRNL) has developed two new, Type B, state-of-the-art, general purpose, fissile material Shipping Packages, designated as 9977 and 9978, as replacements for the U.S. Dept. of Transportation (DOT) specification 6M container. The packages accommodate plutonium, uranium, and other special nuclear materials in bulk quantities and in many forms with capabilities exceeding those of the 6M. A nuclear criticality safety evaluation demonstrates the safe configurations of the new shipping container for plutonium and uranium metal/oxide loading under various conditions for the Safety Analysis Report for Packaging (SARP). The evaluation is in compliance with the performance requirements of 10CFR 71, specifically 10CFR71.55 and 71.59. The criticality safety index (CSI) is 1.0 for most of the contents (Max. Pu Loading -4.4 kg). (authors)

Safety analysis report: packages 238Pu oxide shipping cask (packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Evans, J.E.; Gates, A.A.

1975-06-01

Plutonium-238 (as PuO 2 powder) is shipped in triple-container stainless steel shipping casks in compliance with ERDA Manual Chapter 0529 (ERDAM 0529), Safety Standards for the Packaging of Fissile and Other Radioactive Materials. (U.S.)

Technical and management considerations in conducting type B shipping container tests

International Nuclear Information System (INIS)

Whitney, M.A.; Leader, D.R.; Phipps, D.P.

1994-01-01

The Code of Federal Regulations (CFR) mandate that type B shipping containers are capable of surviving specific drop tests. One approach for demonstrating compliance to the CFRs is to drop test a shipping container. This paper will discuss the technical and management considerations in conducting such drop tests on the 9975 family of shipping containers. For both technical and management considerations this paper will comment on loading the shipping container, dropping the shopping container, and examination of the shipping container after the drop tests

Renovation of DOT specification 21PF-1 protective shipping packages

International Nuclear Information System (INIS)

Barlow, C.R.; Ziehlke, K.T.; Pryor, W.A.; Housholder, W.R.

1985-01-01

Protective shipping packages for isotopically enriched uranium hexafluoride show deterioration with extended service, principally, structural damage from rough handling, and rust damage from exposure to weather and from storage practices which may promote absorption of water by the insulating foam. This report summarizes and/or references work which has been done to evaluate the integrity of the phenolic foam insulation in used shipping packages and outlines the process developed for drying the foam prior to rework of the containers. Mechanical and thermal properties of the foam are not adversely affected by the presence of limited amounts of water, nor are they degraded by the removal process. Rework of the packages, however, must be preceded by moisture removal to slow or avoid continuing rust damage, and tests have shown that drying can be effected by heating at 190 0 F and above for periods of three days or more. Drying progress is monitored by weight loss and/or by use of a moisture meter

Safety analysis report: packages cobalt-60 shipping cask (packaging of radioactive and fissile materials)

International Nuclear Information System (INIS)

Evans, J.E.; Langhaar, J.W.

1973-07-01

Safety Analysis Report DPSPU-73-124-1 replaces DPSPU-69-124-1 and Supplement 1 to permit shipment of 350,000 curies of 60 Co (maximum) in cobalt-60 shipping casks in compliance with 10 CFR Part 71, Packaging of Radioactive Materials for Transport

Analysis of a ship-to-ship collision

International Nuclear Information System (INIS)

Porter, V.L.; Ammerman, D.J.

1996-01-01

Sandia National Laboratories is involved in a safety assessment for the shipment of radioactive material by sea. One part of this study is investigation of the consequences of ship-to-ship collisions. This paper describes two sets of finite element analyses performed to assess the structural response of a small freighter and the loading imparted to radioactive material (RAM) packages during several postulated collision scenarios with another ship. The first series of analyses was performed to evaluate the amount of penetration of the freighter hull by a striking ship of various masses and initial velocities. Although these analyses included a representation of a single RAM package, the package was not impacted during the collision so forces on the package could not be computed. Therefore, a second series of analyses incorporating a representation of a row of seven packages was performed to ensure direct package impact by the striking ship. Average forces on a package were evaluated for several initial velocities and masses of the striking ship. In addition to. providing insight to ship and package response during a few postulated ship collisions scenarios, these analyses will be used to benchmark simpler ship collision models used in probabilistic risk assessment analyses

Renovation of DOT specification 21PF-1 protective shipping packages

International Nuclear Information System (INIS)

Barlow, C.R.; Ziehlke, K.T.; Pryor, W.A.; Housholder, W.R.

1986-01-01

Protective shipping packages for isotopically enriched uranium hexafluoride show deterioration with extended service, principally, structural damage from rough handling, and rust damage from exposure to weather and from storage practices which may promote absorption of water by the insulating foam. This report summarizes and references work which has been done to evaluate the integrity of the phenolic foam insulation in used shipping packages and outlines the process developed for drying the foam prior to rework of the containers. Mechanical and thermal properties of the foam are not adversely affected by the presence of limited amounts of water, nor are they degraded by the removal process. Rework of the packages, however, must be preceded by moisture removal to slow or avoid continuing rust damage, and tests have shown that drying can be effected by heating at 190 0 F and above for periods of three days or more. Drying progress is monitored by weight loss and/or by use of a moisture meter. 3 refs., 6 figs., 2 tabs

Analysis of the qualification test standards for small radioactive material shipping packages

International Nuclear Information System (INIS)

McClure, J.D.

1978-01-01

The study compares the severity of the existing regulatory standards which are used to license radioactive material (RAM) shipping packages with the severity of transportation accidents. The basic findings of the study indicate that the present regulatory standards provide significantly higher levels of protection for surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It was also determined that crush can occur in all of the transport modes and is not presently included in existing regulations for accident conditions. Test proposals are included for the surface transport mode (truck, rail) and the air transport mode

EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

Energy Technology Data Exchange (ETDEWEB)

Smith, A.

2010-07-29

The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

Dynamic analysis to establish normal shock and vibration of radioactive material shipping packages

International Nuclear Information System (INIS)

Fields, S.R.

1980-01-01

A computer model, CARDS (Cask-Railcar Dynamic Simulator) was developed to provide input data for a broad range of radioactive material package-tiedown structural assessments. CARDS simulates the dynamic behavior of shipping packages and their transporters during normal transport conditions. The model will be used to identify parameters which significantly affect the normal shock and vibration environments which, in turn, provide the basis for determining the forces transmitted to the packages

Design of shipping packages to transport varying radioisotopic source materials for future space and terrestrial missions

International Nuclear Information System (INIS)

Barklay, C.D.

1995-01-01

The exploration of space will begin with manned missions to the moon and to Mars, first for scientific discoveries, then for mining and manufacturing. Because of the great financial costs of this type of exploration, it can only be accomplished through an international team effort. This unified effort must include the design, planning and, execution phases of future space missions, extending down to such activities as isotope processing, and shipping package design, fabrication, and certification. All aspects of this effort potentially involve the use of radioisotopes in some capacity, and the transportation of these radioisotopes will be impossible without a shipping package that is certified by the Nuclear Regulatory Commission or the U.S. Department of Energy for domestic shipments, and the U.S. Department of Transportation or the International Atomic Energy Agency for international shipments. To remain without the international regulatory constraints, and still support the needs of new and challenging space missions conducted within ever-shrinking budgets, shipping package concepts must be innovative. A shipping package must also be versatile enough to be reconfigured to transport the varying radioisotopic source materials that may be required to support future space and terrestrial missions. One such package is the Mound USA/9516/B(U)F. Taking into consideration the potential need to transport specific types of radioisotopes, approximations of dose rates at specific distances were determined taking into account the attenuation of dose rate with distance for varying radioisotopic source materials. As a result, it has been determined that the shipping package requirements that will be demanded by future space (and terrestrial) missions can be met by making minor modifications to the USA/9516/B(U)F. copyright 1995 American Institute of Physics

Safety analysis report for packaging: neutron shipping cask, model 0.5T

International Nuclear Information System (INIS)

Peterson, R.T.

1976-01-01

The Safety Analysis Report for Packaging demonstrates that the neutron shipping cask can safely transport, in solid or powder form, all isotopes of uranium, plutonium, americium, curium, berkelium, californium, einsteinium, and fermium. The shipping cask and its contents are described. It also evaluates transport conditions, structural parameters (e.g., load resistance, pressure and impact effects, lifting and tiedown devices), and shielding. Finally, it discusses compliance with Chapter 0529 of the Energy Research and Development Administration Manual

Safety analysis report for packaging: neutron shipping cask, model 4T

International Nuclear Information System (INIS)

Peterson, R.T.

1977-01-01

This Safety Analysis Report for Packaging demonstrates that the neutron shipping cask can safely transport, in solid or powder form, all isotopes of uranium, plutonium, americium, curium, berkelium, californium, einsteinium, and fermium. The cask and its contents are described. It also evaluates transport conditions, structural parameters (e.g., load resistance, pressure and impact effects, lifting and tiedown devices), and shielding. Finally, it discusses compliance with Chapter 0529 of the Energy Research and Development Administration Manual, Safety Standards for the Packaging of Fissile and Other Radioactive Materials

Safety analysis report for packaging Lawrence Livermore Laboratories shipping containers

International Nuclear Information System (INIS)

Evans, J.H.

1975-12-01

The Lawrence Livermore Laboratories shipping containers were designed at Oak Ridge National Laboratory for use in transporting weapons and nuclear components. The design for the containers was evaluated to show compliance with applicable regulations governing packages in which radioactive and fissile materials are transported. Computational procedures were used to determine the structural integrity and thermal behavior of the containers relative to the standards for the normal conditions of transport. A full-scale container test model was destructively tested to verify compliance with the standards for the accident conditions. The results of the analytical evaluations and the tests demonstrate that the design for the Lawrence Livermore Laboratories shipping containers is in compliance with the applicable regulations

Safety Analysis Report for Packaging: The unirradiated fuel shipping container USA/9853/AF

International Nuclear Information System (INIS)

1991-01-01

The HFBR Unirradiated Fuel Shipping Container was designed and fabricated at the Oak Ridge National Laboratory in 1978 for the transport of fuel for the High Flux Beam Reactor (HFBR) for Brookhaven National Laboratory. The package has been evaluated analytically, as well as the comparison to tests on similar packages, to demonstrate compliance with the applicable regulations governing packages in which radioactive and fissile materials are transported. The contents of this Safety Analysis Report for Packaging (SARP) are based on Regulatory Guide 7.9 (proposed Revision 2 - May 1986), 10 CFR Part 71, DOE Order 1540.2, DOE Order 5480.3, and 49 CFR Part 173

Nuclear criticality safety assessment of ORR, NBS, and HFBR fuel element shipping package

International Nuclear Information System (INIS)

Thomas, J.T.

1979-01-01

A fuel element shipping package employing a borated-phenolic foam as a thermal insulating material is designed to transport as many as seven fuel elements for use in the Oak Ridge Research Reactor, the Brookhaven Fast Beam Reactor, or the National Bureau of Standards Reactor. This report presents the criticality safety evaluation and demonstrates that the requirements for a Fissile Class I package are satisfied by the design

Quality assurance program description for shipping packages of radioactive material

International Nuclear Information System (INIS)

1978-01-01

This quality assurance plan describes the quality assurance program at the Pacific Northwest Laboratory (PNL), for shipping packages of radioactive material. The purpose of this report is to describe how PNL will comply with the Code of Federal Regulations, Title 10, Part 71, Appendix E. In compliance with the instructions from the Nuclear Regulatory Commission (NRC), the 18 criteria from Appendix E are covered

Safety analysis report for packaging (SARP) of the Oak Ridge National Laboratory Foamglas Shipping Container

International Nuclear Information System (INIS)

Klima, B.B.; Shappert, L.B.; Seagren, R.D.; Box, W.D.

1979-01-01

An analytical evaluation of the ORNL Foamglas Shipping Container was made to demonstrate its compliance with the regulations governing offsite radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the container complies with the applicable regulations

Nuclear criticality safety analysis for the traveller PWR fuel shipping package

Energy Technology Data Exchange (ETDEWEB)

Vescovi, P.J.; Kent, N.A.; Casado, C.A. [Westinghouse Electric Co., LLC, Columbia, SC (United States)]|[ENUSA Industrias Avanzadas SA, Madrid (Spain)

2004-07-01

The Traveller PWR fresh fuel shipping package represents a radical departure from conventional PWR fuel package designs. Two immediately noticeable features of the Traveller are that it carries a single fuel assembly instead of two as do other package designs, and that it has built-in moderator, which forms part of the flux-trap system. The criticality safety case shows that the Traveller satisfies both U.S. and IAEA licensing requirements, and demonstrates that the package remains acceptably subcritical under normal conditions and hypothetical accident conditions of transport. This paper looks at the modeling techniques that were used to analyze the several accident scenarios that were considered, including: Lattice pitch expansion; Lattice pitch expansion along the fuel assembly length; Preferential flooding (selective flooding of different cavities); Differential flooding (varying water levels inside different cavities); Partial flooding (varying water density); Axial rod displacement; o Sensitivity studies of variable foam densities and boron content in packaging; Analysis for carrying loose rods in a rodbox; The criticality safety case for the Traveller proved to be a successful cooperative effort between ENUSA and Westinghouse.

Nuclear criticality safety analysis for the traveller PWR fuel shipping package

International Nuclear Information System (INIS)

Vescovi, P.J.; Kent, N.A.; Casado, C.A.

2004-01-01

The Traveller PWR fresh fuel shipping package represents a radical departure from conventional PWR fuel package designs. Two immediately noticeable features of the Traveller are that it carries a single fuel assembly instead of two as do other package designs, and that it has built-in moderator, which forms part of the flux-trap system. The criticality safety case shows that the Traveller satisfies both U.S. and IAEA licensing requirements, and demonstrates that the package remains acceptably subcritical under normal conditions and hypothetical accident conditions of transport. This paper looks at the modeling techniques that were used to analyze the several accident scenarios that were considered, including: Lattice pitch expansion; Lattice pitch expansion along the fuel assembly length; Preferential flooding (selective flooding of different cavities); Differential flooding (varying water levels inside different cavities); Partial flooding (varying water density); Axial rod displacement; o Sensitivity studies of variable foam densities and boron content in packaging; Analysis for carrying loose rods in a rodbox; The criticality safety case for the Traveller proved to be a successful cooperative effort between ENUSA and Westinghouse

Safety Analysis Report for Packaging (SARP) of the Oak Ridge National Laboratory Foamglas Shipping Container

International Nuclear Information System (INIS)

Klima, B.B.; Shappert, L.B.; Seagren, R.D.; Box, W.D.

1978-05-01

An analytical evaluation of the Oak Ridge National Laboratory (ORNL) Foamglas Shipping Container was made to demonstrate its compliance with the regulations governing offsite radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the container complies with the applicable regulations

FY2017 status report: Model 9975 O-ring fixture long-term leak performance

Energy Technology Data Exchange (ETDEWEB)

Daugherty, W. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-07-27

A series of experiments to monitor the aging performance of Viton® GLT and GLT-S O-rings used in the Model 9975 shipping package has been ongoing since 2004 at the Savannah River National Laboratory. One approach has been to periodically evaluate the leak performance of O-rings being aged in mock-up 9975 Primary Containment Vessels (PCVs) at elevated temperature. Other methods such as compression-stress relaxation (CSR) tests and field surveillance are also on-going to evaluate O-ring behavior. Seventy tests using PCV mock-ups with GLT O-rings were assembled and heated to temperatures ranging from 200 to 450 ºF. They were leak-tested initially and have been tested periodically to determine if they continue to meet the leak-tightness criterion defined in ANSI standard N14.5-97. Due to material substitution, a smaller test matrix with fourteen additional tests was initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 ºF. Leak test failures have been experienced in all of the GLT O-ring fixtures aging at 350 ºF and higher temperatures, and in 8 fixtures aging at 300 ºF. The 300 °F GLT O-ring fixtures failed after 2.8 to 5.7 years at temperature. The remaining GLT O-ring fixtures aging at 300 ºF were retired from testing following more than 5 years at temperature without failure. No failures have yet been observed in GLT O-ring fixtures aging at 200 ºF for 9 to 10.5 years, or in GLT O-ring fixtures aging at 270 ºF for 5.7 years. These aging temperatures bound O-ring temperatures anticipated during normal storage in K-Area Complex (KAC). Leak test failures have been experienced in all of the GLT-S O-ring fixtures aging at 300 ºF and above. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 and 250 ºF for 6.9 to 7.5 years. Data from the O-ring fixtures are generally consistent with results from compression stress relaxation testing, and provide confidence in the predictive models based on those results

Acoustic performance design and optimal allocation of sound package in ship cabin noise reduction

Directory of Open Access Journals (Sweden)

YANG Deqing

2017-08-01

Full Text Available The sound package in noise reduction design of ship cabins has become the main approach for the future. The sound package is a specially designed acoustic component consisting of damping materials, absorption materials, sound isolation materials and base structural materials which can achieve the prescribed performance of noise reduction. Based on the Statistical Energy Analysis(SEAmethod, quick evaluation and design methods, and the optimal allocation theory of sound packages are investigated. The standard numerical acoustic performance evaluation model, sound package optimization design model and sound package optimal allocation model are presented. A genetic algorithm is applied to solve the presented optimization problems. Design examples demonstrate the validity and efficiency of the proposed models and solutions. The presented theory and methods benefit the standardization and programming of sound package design, and decrease noise reduction costs.

Design of an experiment to measure fire exposure of packages aboard container cargo ships

International Nuclear Information System (INIS)

Koski, J.A.

1998-01-01

The test described in this paper is intended to measure the typical accident environment for a radioactive materials package in a fire abroad a container cargo ship. A stack of nice used standard cargo containers will be variously loaded with empty packages, simulated packages and combustible cargo and placed over a large hydrocarbon pool fire of one hour duration. Fire environments, both inside and outside the containers, typical of on-deck stowage will be measured as well as the potential for container-to-container fire spread. With the use of the inverse heat conduction calculations, the local heat transfer to the simulated packages can be estimated from thermocouple data. Data recorded will also provide information on fire durations in each container, fire intensity and container-to-container fire spread characteristics. (authors)

Safety Analysis Report for Packaging (SARP) of the Oak Ridge National Laboratory Shipping Cask D-38. Revision 1

International Nuclear Information System (INIS)

Box, W.D.; Shappert, L.B.; Seagren, R.D.; Watson, C.D.; Hammond, C.R.; Klima, B.B.

1979-09-01

An analytical evaluation of the Oak Ridge National Laboratory Shipping Cask D-38 (solids shipments) was made to demonstrate its compliance with the regulations governing off-site radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the cask complies with the applicable regulations

Safety Analysis Report for Packaging (SARP) of the Oak Ridge National Laboratory Shipping Cask D-38. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Box, W.D.; Shappert, L.B.; Seagren, R.D.; Watson, C.D.; Hammond, C.R.; Klima, B.B.

1979-09-01

An analytical evaluation of the Oak Ridge National Laboratory Shipping Cask D-38 (solids shipments) was made to demonstrate its compliance with the regulations governing off-site radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the cask complies with the applicable regulations.

An analysis of the qualification criteria for small radioactive material shipping packages

International Nuclear Information System (INIS)

McClure, J.D.

1983-05-01

The RAM package design certification process has two important elements, testing and acceptance. These terms sound very similar but they have specific meanings. Qualification testing in the context of this study is the imposition of simulated accident test conditions upon the candidate package design. (Normal transportation environments may also be included.) Following qualification testing, the acceptance criteria provide the performance levels which, if demonstrated, indicate the ability of the RAM package to sustain the severity of the qualification testing sequence and yet maintain specified levels of package integrity. This study has used Severities of Transportation Accidents as a data base to examine the regulatory test criteria which are required to be met by small packages containing Type B quantities of radioactive material (RAM). The basic findings indicate that the present regulatory test standards provide significantly higher levels of protection for the surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It should also be noted that various risk assessment studies have shown that the risk to the public due to severe transport accidents by surface and air transport modes is very low. A key element in this study was the quantification of the severity of the transportation accident environment and the severity of the present qualification test standards (called qualification test standards in this document) so that a direct comparison could be made between them to assess the effectiveness of the existing qualification test standards. The manner in which this was accomplished is described

An analysis of the qualification criteria for small radioactive material shipping packages

Energy Technology Data Exchange (ETDEWEB)

McClure, J.D.

1983-05-01

The RAM package design certification process has two important elements, testing and acceptance. These terms sound very similar but they have specific meanings. Qualification testing in the context of this study is the imposition of simulated accident test conditions upon the candidate package design. (Normal transportation environments may also be included.) Following qualification testing, the acceptance criteria provide the performance levels which, if demonstrated, indicate the ability of the RAM package to sustain the severity of the qualification testing sequence and yet maintain specified levels of package integrity. This study has used Severities of Transportation Accidents as a data base to examine the regulatory test criteria which are required to be met by small packages containing Type B quantities of radioactive material (RAM). The basic findings indicate that the present regulatory test standards provide significantly higher levels of protection for the surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It should also be noted that various risk assessment studies have shown that the risk to the public due to severe transport accidents by surface and air transport modes is very low. A key element in this study was the quantification of the severity of the transportation accident environment and the severity of the present qualification test standards (called qualification test standards in this document) so that a direct comparison could be made between them to assess the effectiveness of the existing qualification test standards. The manner in which this was accomplished is described.

Evaluating the loss of a LWR spent fuel or plutonium shipping package into the sea

International Nuclear Information System (INIS)

Heaberlin, S.W.; Baker, D.A.

1976-06-01

As the nations of the world turn to nuclear power for an energy source, commerce in nuclear fuel cycle materials will increase. Some of this commerce will be transported by sea. Such shipments give rise to the possibility of loss of these materials into the sea. This paper discusses the postulated accidental loss of two materials, light water reactor (LWR) spent fuel and plutonium, at sea. The losses considered are that of a single shipping package which is either undamaged or damaged by fire prior to the loss. The containment failure of the package in the sea,

Thermal Analysis of the SAFKEG Package for Long Term Storage

International Nuclear Information System (INIS)

NARENDRA, GUPTA

2005-01-01

Interim plutonium storage for up to 10 years in the K-reactor building is currently being planned at Savannah River Site (SRS). SAFKEG package could be used to store Pu metal and oxide (PuO2) in the K-reactor complex with other packagings like 9975. The SAFKEG is designed for carrying Type-B materials across the DOE complex and meets the 10CFR71 requirements. Thermal analyses were performed to ensure that the temperatures of the SAFKEG components will not exceed their temperature limits under the K-reactor storage conditions. Thermal analyses of the SAFKEG packaging with three content configurations using BNFL 3013 outer container (Rocky Flats, SRS bagless transfer cans, and BNFL inner containers) were performed for storage of PuO2 and plutonium metal

Fifth Interim Status Report: Model 9975 PCV O-Ring Fixture Long-Term Leak Performance

International Nuclear Information System (INIS)

Daugherty, W.; Hoffman, E.

2010-01-01

A series of experiments to monitor the aging performance of Viton reg. GLT O-rings used in the Model 9975 package has been ongoing for six years at the Savannah River National Laboratory. Sixty-seven mock-ups of 9975 Primary Containment Vessels (PCVs) were assembled and heated to temperatures ranging from 200 to 450 F. They were leak-tested initially and have been tested at nominal six month intervals to determine if they meet the criterion of leaktightness defined in ANSI standard N14.5-97. Fourteen additional tests were initiated in 2008 with GLT-S O-rings heated to temperatures ranging from 200 to 400 F. High temperature aging continues for 36 GLT O-ring fixtures at 200--350 F. Room temperature leak test failures have been experienced in 5 of the GLT O-ring fixtures aging at 300 and 350 F, and in all 3 of the GLT O-ring fixtures aging at higher temperatures. No failures have yet been observed in GLT O-ring fixtures aging at 200 F for 30--48 months, which is still bounding to O-ring temperatures during storage in KAMS. High temperature aging continues for 6 GLT-S O-ring fixtures at 200--300 F. Room temperature leak test failures have been experienced in all 8 of the GLT-S O-ring fixtures aging at 350 and 400 F. No failures have yet been observed in GLT-S O-ring fixtures aging at 200 or 300 F for 19 months. For O-ring fixtures that have failed the room temperature leak test and been disassembled, the O-rings displayed a compression set ranging from 51--95%. This is significantly greater than seen to date for packages inspected during KAMS field surveillance (23% average). For GLT O-rings, service life based on the room temperature leak rate criterion is comparable to that predicted by compression stress relaxation (CSR) data at higher temperatures (350--400 F). While there are no comparable failure data yet at aging temperatures below 300 F, extrapolations of the data for GLT O-rings suggests that CSR model predictions provide a conservative prediction of service

Simulation of the dynamic response of radioactive material shipping package - railcar systems during coupling operations

International Nuclear Information System (INIS)

Fields, S.R.

1981-12-01

The basic equations of the computer model CARDS (Cask-Railcar Dynamic Simulator), developed for the U.S. Nuclear Regulatory Commission to simulate the dynamic behavior of radioactive material shipping package - railcar systems, are presented. A companion model, CARRS (Casks Railcar Response Spectrum Generator), that generates system response as frequency response spectra is also presented in terms of its basic equations

Simulation of the dynamic response of radioactive material shipping package-railcar systems during coupling operations

International Nuclear Information System (INIS)

Fields, S.R.

1983-10-01

The basic equations of the computer model CARDS (Cask-Railcar Dynamic Simulator), developed for the US Nuclear Regulatory Commission to simulate the dynamic behavior of radioactive material shipping package - railcar systems, are presented. A companion model, CARRS (Cask Railcar Response Spectrum Generator), that generates system response as frequency response spectra is also presented in terms of its basic equations. 1 reference, 18 figures

Design of an experiment to measure the fire exposure of radioactive materials packages aboard container cargo ships

International Nuclear Information System (INIS)

Koski, J.A.

1997-11-01

The test described in this paper is intended to measure the typical accident environment for a radioactive materials package in a fire aboard a container cargo ship. A stack of nine used standard cargo containers will be variously loaded with empty packages, simulated packages and combustible cargo and placed over a large hydrocarbon pool fire of one hour duration. Both internal and external fire container fire environments typical of on-deck stowage will be measured as well as the potential for container to container fire spread. With the use of the inverse heat conduction calculations, the local heat transfer to the simulated packages can be estimated from thermocouple data. Data recorded will also provide information on fire durations in each container, fire intensity and container to container fire spread characteristics

Safety analysis report for the TRUPACT-II shipping package (condensed version). Volume 2, Rev. 14

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-10-01

This appendix determines the effective G values for payload shipping categories of contact handled transuranic (CH-TRU) waste materials, based on the radiolytic G values for waste materials that are discussed in detail in Appendix 3.6.8 of the Safety Analysis Report for the TRUPACT-II Shipping Package. The effective G values take into account self-absorption of alpha decay energy inside particulate contamination and the fraction of energy absorbed by nongas-generating materials. As described in Appendix 3.6.8, an effective G value, G{sub eff}, is defined by: G{sub eff} - {Sigma}{sub M} (F{sub M} x G{sub M}) F{sub M}-fraction of energy absorbed by material maximum G value for a material where the sum is over all materials present inside a waste container. The G value itself is determined primarily by the chemical properties of the material and its temperature. The value of F is determined primarily by the size of the particles containing the radionuclides, the distribution of radioactivity on the various materials present inside the waste container, and the stopping distance of alpha particles in air, in the waste materials, or in the waste packaging materials.

Safety analysis report for the TRUPACT-II shipping package (condensed version). Volume 2, Rev. 14

International Nuclear Information System (INIS)

1994-10-01

This appendix determines the effective G values for payload shipping categories of contact handled transuranic (CH-TRU) waste materials, based on the radiolytic G values for waste materials that are discussed in detail in Appendix 3.6.8 of the Safety Analysis Report for the TRUPACT-II Shipping Package. The effective G values take into account self-absorption of alpha decay energy inside particulate contamination and the fraction of energy absorbed by nongas-generating materials. As described in Appendix 3.6.8, an effective G value, G eff , is defined by: G eff - Σ M (F M x G M ) F M -fraction of energy absorbed by material maximum G value for a material where the sum is over all materials present inside a waste container. The G value itself is determined primarily by the chemical properties of the material and its temperature. The value of F is determined primarily by the size of the particles containing the radionuclides, the distribution of radioactivity on the various materials present inside the waste container, and the stopping distance of alpha particles in air, in the waste materials, or in the waste packaging materials

Perturbation of baseline thermal stress in the Mound 9516 Shipping Package primary containment vessel

International Nuclear Information System (INIS)

Sansalone, K.H.F.

1995-01-01

Full-capacity loading of heat sources into the Mound 9516 Shipping Package primary containment vessel (PCV) results in temperature gradients which are symmetric, due to the axisymmetry of the package design. Concern over the change in thermal gradients (and therefore, stress) in the PCV due to sub-capacity loading led to the analytical examination of this phenomenon. The PCVs are cylindrical in shape and are loaded into the package such that they and all containment components are concentrically arranged along a common longitudinal axis. If the design full-capacity loading of the PCVs in this package assumes the axisymmetric (or more precisely, cyclicly symmetric) arrangement of its heat-producing contents, then sub-capacity loading implies that in many cases, the load arrangement could be asymmetric with respect to the longitudinal axis. It is then feasible that the departure from heat load axisymmetry could perturb the nominal thermal gradients so that thermally-induced stress within the PCV might increase to levels deemed unacceptable. This study applies Finite Element analysis (FEA) to the problem and demonstrates that no such unacceptable thermal stress increase occurs in the PCV material due to the asymmetric arrangement of contents. copyright 1995 American Institute of Physics

Safety analysis report for packaging (SARP) of the Oak Ridge National Laboratory. TRU curium shipping container

International Nuclear Information System (INIS)

Box, W.D.; Klima, B.B.; Seagren, R.D.; Shappert, L.B.; Aramayo, G.A.

1980-06-01

An analytical evaluation of the Oak Ridge National Laboratory Transuranium (TRU) Curium Shipping Container was made to demonstrate its compliance with the regulations governing offsite shipment of packages containing radioactive material. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the container complies with the applicable regulations

REVIEW OF AGING DATA ON EPDM O-RINGS IN THE H1616 SHIPPING PACKAGE

Energy Technology Data Exchange (ETDEWEB)

Skidmore, E.

2012-03-27

Currently, all H1616 shipping package containers undergo annual re-verification testing, including containment vessel leak testing to verify leak-tightness (<1 x 10{sup -7} ref cc/sec air) as per ANSI N14.5. The purpose of this literature review is to supplement aging studies currently being performed by SRNL on the EPDM O-rings to provide the technical basis for extending annual re-verification testing for the H1616 shipping package and to predict the life of the seals at bounding service conditions. The available data suggest that the EPDM O-rings can retain significant mechanical properties and sealing force at or below bounding service temperatures (169 F or 76 C) beyond the 1 year maintenance period. Interpretation of available data suggests that a service life of at least 2 years and potentially 4-6 years may be possible at bounding temperatures. Seal lifetimes at lower, more realistic temperatures will likely be longer. Being a hydrocarbon elastomer, EPDM O-rings may exhibit an inhibition period due to the presence of antioxidants. Once antioxidants are consumed, mechanical properties and seal performance could decline at a faster rate. Testing is being performed to validate the assumptions outlined in this report and to assess the long-term performance of O-ring seals under actual service conditions.

Greater-than-Class C low-level radioactive waste shipping package/container identification and requirements study

International Nuclear Information System (INIS)

Tyacke, M.

1993-08-01

This report identifies a variety of shipping packages (also referred to as casks) and waste containers currently available or being developed that could be used for greater-than-Class C (GTCC) low-level waste (LLW). Since GTCC LLW varies greatly in size, shape, and activity levels, the casks and waste containers that could be used range in size from small, to accommodate a single sealed radiation source, to very large-capacity casks/canisters used to transport or dry-store highly radioactive spent fuel. In some cases, the waste containers may serve directly as shipping packages, while in other cases, the containers would need to be placed in a transport cask. For the purpose of this report, it is assumed that the generator is responsible for transporting the waste to a Department of Energy (DOE) storage, treatment, or disposal facility. Unless DOE establishes specific acceptance criteria, the receiving facility would need the capability to accept any of the casks and waste containers identified in this report. In identifying potential casks and waste containers, no consideration was given to their adequacy relative to handling, storage, treatment, and disposal. Those considerations must be addressed separately as the capabilities of the receiving facility and the handling requirements and operations are better understood

Safety Analysis Report for Packaging (SARP) of the Oak Ridge National Laboratory TRU Californium Shipping Container

International Nuclear Information System (INIS)

Box, W.D.; Shappert, L.B.; Seagren, R.D.; Klima, B.B.; Jurgensen, M.C.; Hammond, C.R.; Watson, C.D.

1980-01-01

An analytical evaluation of the Oak Ridge National Laboratory TRU Californium Shipping Container was made in order to demonstrate its compliance with the regulations governing off-site shipment of packages that contain radioactive material. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of this evaluation demonstrate that the container complies with the applicable regulations

Type A radioactive liquid sample packaging family

International Nuclear Information System (INIS)

Edwards, W.S.

1995-11-01

Westinghouse Hanford Company (WHC) has developed two packagings that can be used to ship Type A quantities of radioactive liquids. WHC designed these packagings to take advantage of commercially available items where feasible to reduce the overall packaging cost. The Hedgehog packaging can ship up to one liter of Type A radioactive liquid with no shielding and 15 cm of distance between the liquid and the package exterior, or 30 ml of liquid with 3.8 cm of stainless steel shielding and 19 cm of distance between the liquid and the package exterior. The One Liter Shipper can ship up to one liter of Type A radioactive liquid that does not require shielding

Leveraging Available Data to Support Extension of Transportation Packages Service Life

Energy Technology Data Exchange (ETDEWEB)

Dunn, K.; Abramczyk, G.; Bellamy, S.; Daugherty, W.; Hackney, B.; Hoffman, E.; Skidmore, E.; Stefek, T.

2012-06-12

Data obtained from testing shipping package materials have been leveraged to support extending the service life of select shipping packages while in nuclear materials transportation. Increasingly, nuclear material inventories are being transferred to an interim storage location where they will reside for extended periods of time. Use of a shipping package to store nuclear materials in an interim storage location has become more attractive for a variety of reasons. Shipping packages are robust and have a qualified pedigree for their performance in normal operation and accident conditions within the approved shipment period and storing nuclear material within a shipping package results in reduced operations for the storage facility. However, the shipping package materials of construction must maintain a level of integrity as specified by the safety basis of the storage facility through the duration of the storage period, which is typically well beyond the one year transportation window. Test programs have been established to obtain aging data on materials of construction that are the most sensitive/susceptible to aging in certain shipping package designs. The collective data are being used to support extending the service life of shipping packages in both transportation and storage.

Leveraging Available Data to Support Extension of Transportation Packages Service Life

International Nuclear Information System (INIS)

Dunn, K.; Abramczyk, G.; Bellamy, S.; Daugherty, W.; Hackney, B.; Hoffman, E.; Skidmore, E.; Stefek, T.

2012-01-01

Data obtained from testing shipping package materials have been leveraged to support extending the service life of select shipping packages while in nuclear materials transportation. Increasingly, nuclear material inventories are being transferred to an interim storage location where they will reside for extended periods of time. Use of a shipping package to store nuclear materials in an interim storage location has become more attractive for a variety of reasons. Shipping packages are robust and have a qualified pedigree for their performance in normal operation and accident conditions within the approved shipment period and storing nuclear material within a shipping package results in reduced operations for the storage facility. However, the shipping package materials of construction must maintain a level of integrity as specified by the safety basis of the storage facility through the duration of the storage period, which is typically well beyond the one year transportation window. Test programs have been established to obtain aging data on materials of construction that are the most sensitive/susceptible to aging in certain shipping package designs. The collective data are being used to support extending the service life of shipping packages in both transportation and storage.

An assessment of simplified methods to determine damage from ship-to-ship collisions

International Nuclear Information System (INIS)

Parks, M.B.; Ammerman, D.J.

1996-01-01

Sandia National Laboratories (SNL) is studying the safety of shipping, radioactive materials (RAM) by sea, the SeaRAM project (McConnell, et al. 1995), which is sponsored by the US Department of Energy (DOE). The project is concerned with the potential effects of ship collisions and fires on onboard RAM packages. Existing methodologies are being assessed to determine their adequacy to predict the effect of ship collisions and fires on RAM packages and to estimate whether or not a given accident might lead to a release of radioactivity. The eventual goal is to develop a set of validated methods, which have been checked by comparison with test data and/or detailed finite element analyses, for predicting the consequences of ship collisions and fires. These methods could then be used to provide input for overall risk assessments of RAM sea transport. The emphasis of this paper is on methods for predicting- effects of ship collisions

Packaging design criteria for the Hanford Ecorok Packaging

International Nuclear Information System (INIS)

Mercado, M.S.

1996-01-01

The Hanford Ecorok Packaging (HEP) will be used to ship contaminated water purification filters from K Basins to the Central Waste Complex. This packaging design criteria documents the design of the HEP, its intended use, and the transportation safety criteria it is required to meet. This information will serve as a basis for the safety analysis report for packaging

Method of estimating the leakage of multiple barriers in a radioactive materials shipping package

International Nuclear Information System (INIS)

Towell, R.H.; Kapoor, A.; Oras, J.J.

1997-01-01

This paper presents the results of a theoretical study of the performance of multiple leaky barriers in containing radioactive materials in a shipping package. The methods used are reasoned analysis and finite element modeling barriers. The finite element model is developed and evaluated with parameters set to bracket 6M configurations with three to six nested plastic jars, food-pack cans, and plastic bags inside Department of Transportation (DOT) Specification 2R inner containers with pipe thread closures. The results show that nested barriers reach the regulatory limit of 1x10 -6 A 2 /hr in 11 to 52 days, even though individually the barriers would exceed the regulatory limit by a factor of as much as 370 instantaneously. These times are within normal shipping times. The finite element model is conservative because it does not consider the deposition and sticking of the leaking radioactive material on the surfaces inside each boundary

User's guide for shipping Type B quantities of radioactive and fissile material, including plutonium, in DOT-6M specification packaging configurations

International Nuclear Information System (INIS)

Kelly, D.L.

1994-09-01

The need for developing a user's guide for shipping Type B quantities of radioactive and fissile material, including plutonium, in a US Department of Transportation Specification 6M (DOT-6M) packaging was identified by the US Department of Energy (DOE)-Headquarters, Transportation Management Division (EM-261) because the DOT-6M packaging is widely used by DOE site contractors and the DOE receives many questions about approved packaging configuration. Currently, EM-261 has the authority to approve new DOT-6M packaging configurations for use by the DOE Operations Offices. This user's guide identifies the DOE-approved DOT-6M packaging configurations and explains how to have new configurations approved by the DOE. The packaging configurations described in this guide are approved by the DOE, and satisfy the applicable DOT requirements and the identified DOE restrictions. These packaging configurations are acceptable for transport of Type B quantities of radioactive and fissile material, including plutonium

Consequences of postulated losses of LWR spent fuel and plutonium shipping packages at sea

International Nuclear Information System (INIS)

Heaberlin, S.W.; Baker, D.A.; Beyer, C.E.; Friley, J.R.; Mandel, S.; Peterson, P.L.; Sominen, F.A.

1977-10-01

The potential consequences of the loss of a large spent fuel cask and of a single 6M plutonium shipping package into the sea for two specific accident cases are estimated. The radiation dose to man through the marine food chain following the loss of undamaged and fire-damaged packages to the continental shelf and in the deep ocean are conservatively estimated. Two failure mechanisms that could lead to release of radioactive material after loss of packages into the ocean have been considered: corrosion and hydrostatic pressure. A third possible mechanism is thermal overpressurization following burial in marine sediments. It was determined that the seals or pressure relief devices on an undamaged spent fuel cask might fail from hydrostatic forces for losses on the continental shelf although some cask designs would retain their integrity at this depth. The population dose to man through the marine food chain following these scenarios has been estimated. The dose estimates are made relating the radioactive material released and the seafood productivity in the region of the release. Doses are based on a one-year consumption of contaminated seafood. The loss of a single plutonium package on the continental shelf is estimated to produce a population dose commitment of less than 250 man-rem for recycle plutonium. The dose commitment to the average individual is less than one millirem. Doses for losses of undamaged casks to the continental shelf and deep ocean and for loss of a fire-damaged cask to the deep ocean were determined to be several orders of magnitude smaller. 22 tables, 10 figures

Thermal Evaluation of a KRI-BGM Shipping Cask

International Nuclear Information System (INIS)

Bang, K. S.; Lee, J. C.; Seo, K. S.

2007-01-01

Radioactive isotopes are used extensively in the fields of industry, medical treatment, food and agriculture. Use of radioactive isotopes is expected to increase continuously with the growth of each field. In order to safely transport radioactive isotopes from the place of manufacture to the place of use, a shipping package is required. Therefore KAERI is developing the KRI-BGM shipping cask to transport the Ir-192 bulk radioactive material, which is produced at the HANARO research reactor. The shipping package should satisfy the requirements which are prescribed in the Korea MOST Act 2001-23, IAEA Safety Standard Series No. TS-R-1, US 10 CFR Part 71 and the US 49 CFR Part 173. These regulatory classify the KRI-BGM shipping cask as a Type B package, and their regulatory guidelines state that the Type B package for transporting radioactive materials should be able to withstand a period of 30 minutes under a thermal condition of 800 .deg. C. However, the polyurethane, which is to be used as the filling within the cavity of the KRIBGM shipping cask, has a very weak characteristic in a high temperature. Therefore it is difficult for the depleted uranium(hereafter DU), which is used as shielding material, to be protected under a thermal condition of 800 .deg. C. Accordingly, the KRI-BGM shipping cask, which applied non-combustible polyurethane and fireproof materials as the filling, was fabricated. The thermal tests by using prototype cask have been performed to estimate the thermal integrity of the KRI-BGM shipping cask under a thermal condition of 800 .deg. C

Dose assessment for public by packages shipping radioactive materials hypothetically sunk on the continental shelf. Annex 3

International Nuclear Information System (INIS)

Tsumune, Daisuke; Suzuki, Hiroshi; Saegusa, Toshiari; Watabe, Naohito; Asano, Hiroyuki; Maruyama, Koki; Kinehara, Yoshiki

2001-01-01

Radioactive materials such as spent fuel (SF), PuO 2 powder, high level wastes (HLW) and fresh mixed oxide (MOX) fuel have been transported by sea between Europe and Japan. Dose assessments for public have been performed in the past when the packages shipping radioactive materials were hypothetically sunk on the continental shelf. These studies employed various conditions and methods in their assessments and the results were not always the same. In this study, the dose assessment for these packages was performed under the same conditions and by the same methods. The effective dose equivalents of radiation exposure to the public for all materials become smaller than the previous evaluations due to more realistic assumption in this study. These evaluated results are far less than the effective dose equivalent limit (1 mSv year -1 ) by the ICRP recommendation. (author)

Beneficial uses shipping system (BUSS) cask, safety analysis report for packaging: Volumes 1 and 2

International Nuclear Information System (INIS)

Ferrell, P.C.

1997-01-01

The Beneficial Uses Shipping System (BUSS) cask Safety Analysis Report for Packaging (SARP) was originally prepared by Sandia National Laboratory (SNL). After the certification process was completed, the ownership of the BUSS cask and associated SARP was transferred from SNL to the DOE Hanford site in Richland, Washington. During timely renewal of the BUSS cask certificate of compliance, the SARP was revised to (1) respond to the timely renewal questions, (2) consolidate the previous revision made by SNL, and (3) bring the SARP into compliance with the 1996 version of 10 CFR 71. Since the BUSS cask is now the responsibility of RL, the SARP was reissued as a Hanford document

21 CFR 820.130 - Device packaging.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Device packaging. 820.130 Section 820.130 Food and... QUALITY SYSTEM REGULATION Labeling and Packaging Control § 820.130 Device packaging. Each manufacturer shall ensure that device packaging and shipping containers are designed and constructed to protect the...

Big rock point restoration project BWR major component removal, packaging and shipping - planning and experience

International Nuclear Information System (INIS)

Milner, T.; Dam, S.; Papp, M.; Slade, J.; Slimp, B.; Nurden, P.

2001-01-01

The Big Rock Point boiling water reactor (BWR) at Charlevoix, MI was permanently shut down on August 29th 1997. In 1999 BNFL Inc.'s Reactor Decommissioning Group (RDG) was awarded a contract by Consumers Energy (CECo) for the Big Rock Point (BRP) Major Component Removal (MCR) project. BNFL Inc. RDG has teamed with MOTA, Sargent and Lundy and MDM Services to plan and execute MCR in support of the facility restoration project. The facility restoration project will be completed by 2005. Key to the success of the project has been the integration of best available demonstrated technology into a robust and responsive project management approach, which places emphasis on safety and quality assurance in achieving project milestones linked to time and cost. To support decommissioning of the BRP MCR activities, a reactor vessel (RV) shipping container is required. Discussed in this paper is the design and fabrication of a 10 CFR Part 71 Type B container necessary to ship the BRP RV. The container to be used for transportation of the RV to the burial site was designed as an Exclusive Use Type B package for shipment and burial at the Barnwell, South Carolina (SC) disposal facility. (author)

Safety analysis report: packages. Argonne National Laboratory SLSF test train shipping container, P-1 shipment. Fissile material. Final report

International Nuclear Information System (INIS)

Meyer, C.A.

1975-06-01

The package is used to ship an instrumented test fuel bundle (test train) containing fissile material. The package assembly is Argonne National Laboratory (ANL) Model R1010-0032. The shipment is fissile class III. The packaging consists of an outer carbon steel container into which an inner container is placed; the inner container is separated from the outer container by urethane foam cushioning material. The test train is supported in the inner container by a series of transverse supports spaced along the length of the test train. Both the inner and outer containers are closed with bolted covers. The covers do not seal the containers in a leaktight manner. The gross weight of the shipment is about 8350 lb. The unirradiated fissile material content is less than 3 kg of UO 2 of up to 93.2 percent enrichment. This is a Type A quantity (transport group III and less than 3 curies) of radioactive material which does not require shielding, cooling or heating, or neutron absorption or moderation functions in its packaging. The maximum exterior dimensions of the container are 37 ft 11 in. long, 24 1 / 2 in. wide, and 19 3 / 4 in. high

Refurbishment and modification of existing protective shipping packages (for 30-inch UF{sub 6} cylinders) per USDOT specification No. USA-DOT-21PF-1A

Energy Technology Data Exchange (ETDEWEB)

Housholder, W.R. [Nuclear Containers, Incorporated, Elizabethton, TN (United States)

1991-12-31

This paper addresses the refurbishment procedures for existing shipping containers for 30-inch diameter UF{sub 6} cylinders in accordance with DOT Specification 21PF-1 and the criteria used to determine rejection when such packages are unsuitable for refurbishment.

Safety analysis report: packages. LP-12 tritium package (packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Gates, A.A.; McCarthy, P.G.; Edl, J.W.

1975-05-01

Elemental tritium is shipped at low pressure in a stainless steel container (LP-12) within an aluminum vessel and surrounded by 3.9 in.-thick Celotex insulation in a steel drum. Information is presented on the packaging design, evaluation of the structural, thermal, containment, shielding, and criticality characteristics of the package, procedures for loading, unloading, transporting, and testing the LP-12, and quality assurance requirements. (U.S.)

9 CFR 381.144 - Packaging materials.

Science.gov (United States)

2010-01-01

... to health. All packaging materials must be safe for the intended use within the meaning of section..., from the packaging supplier under whose brand name and firm name the material is marketed to the... distinguishing brand name or code designation appearing on the packaging material shipping container; must...

DYNAMIC ANALYSIS OF THE BULK TRITIUM SHIPPING PACKAGE SUBJECTED TO CLOSURE TORQUES AND SEQUENTIAL IMPACTS

International Nuclear Information System (INIS)

Wu, T; Paul Blanton, P; Kurt Eberl, K

2007-01-01

This paper presents a finite-element technique to simulate the structural responses and to evaluate the cumulative damage of a radioactive material packaging requiring bolt closure-tightening torque and subjected to the scenarios of the Hypothetical Accident Conditions (HAC) defined in the Code of Federal Regulations Title 10 part 71 (10CFR71). Existing finite-element methods for modeling closure stresses from bolt pre-load are not readily adaptable to dynamic analyses. The HAC events are required to occur sequentially per 10CFR71 and thus the evaluation of the cumulative damage is desirable. Generally, each HAC event is analyzed separately and the cumulative damage is partially addressed by superposition. This results in relying on additional physical testing to comply with 10CFR71 requirements for assessment of cumulative damage. The proposed technique utilizes the combination of kinematic constraints, rigid-body motions and structural deformations to overcome some of the difficulties encountered in modeling the effect of cumulative damage. This methodology provides improved numerical solutions in compliance with the 10CFR71 requirements for sequential HAC tests. Analyses were performed for the Bulk Tritium Shipping Package (BTSP) designed by Savannah River National Laboratory to demonstrate the applications of the technique. The methodology proposed simulates the closure bolt torque preload followed by the sequential HAC events, the 30-foot drop and the 30-foot dynamic crush. The analytical results will be compared to the package test data

Packaging configurations and handling requirements for nuclear materials

International Nuclear Information System (INIS)

Jefferson, R.M.

1981-01-01

The basic safety concepts for radioactive material are that the package is the primary protection for the public, that the protection afforded by the package should be proportional to the hazard and that the package must be proved by performance. These principles are contained in Department of Energy (DOE), Nuclear Regulatory Commission (NRC) and Department of Transportation (DOT) regulations which classify hazards of various radioactive materials and link packaging requirements to the physical form and quantities being shipped. Packaging requirements are reflected in performance standards to guarantee that shipments of low hazard quantities will survive the rigors of normal transportation and that shipments of high hazard quantities will survive extreme severity transportation accidents. Administrative controls provide for segregation of radioactive material from people and other sensitive or hazardous material. They also provide the necessary information function to control the total amounts in a conveyance and to assure that appropriate emergency response activities be started in case of accidents or other emergencies. Radioactive materials shipped in conjunction with the nuclear reactor programs include, ores, concentrates, gaseous diffusion feedstocks, enriched and depleted uranium, fresh fuel, spent fuel, high level wastes, low level wastes and transuranic wastes. Each material is packaged and shipped in accordance with regulations and all hazard classes, quantity limits and packaging types are called into use. From the minimal requirements needed to ship the low hazard uranium ores or concentrates to the very stringent requirements in packaging and moving high level wastes or spent fuel, the regulatory system provides a means for carrying out transportation of radioactive material which assures low and controlled risk to the public

Hazardous Material Packaging and Transportation

Energy Technology Data Exchange (ETDEWEB)

Hypes, Philip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-02-04

This is a student training course. Some course objectives are to: recognize and use standard international and US customary units to describe activities and exposure rates associated with radioactive material; determine whether a quantity of a single radionuclide meets the definition of a class 7 (radioactive) material; determine, for a given single radionuclide, the shipping quantity activity limits per 49 Code of Federal Regulations (CFR) 173.435; determine the appropriate radioactive material hazard class proper shipping name for a given material; determine when a single radionuclide meets the DOT definition of a hazardous substance; determine the appropriate packaging required for a given radioactive material; identify the markings to be placed on a package of radioactive material; determine the label(s) to apply to a given radioactive material package; identify the entry requirements for radioactive material labels; determine the proper placement for radioactive material label(s); identify the shipping paper entry requirements for radioactive material; select the appropriate placards for a given radioactive material shipment or vehicle load; and identify allowable transport limits and unacceptable transport conditions for radioactive material.

Safety evaluation for packaging (onsite) concrete-lined waste packaging

Energy Technology Data Exchange (ETDEWEB)

Romano, T.

1997-09-25

The Pacific Northwest National Laboratory developed a package to ship Type A, non-transuranic, fissile excepted quantities of liquid or solid radioactive material and radioactive mixed waste to the Central Waste Complex for storage on the Hanford Site.

7 CFR 905.140 - Gift packages.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Gift packages. 905.140 Section 905.140 Agriculture... TANGELOS GROWN IN FLORIDA Rules and Regulations Non-Regulated Fruit § 905.140 Gift packages. Any handler..., ship any varieties for the following purpose and types of shipment: (a) To any person gift packages...

Experimental ship fire measurements with simulated radioactive cargo

International Nuclear Information System (INIS)

Koski, J.A.; Arviso, M.; Bobbe, J.G.; Wix, S.D.; Cole, J.K.; Hohnstreiter, G.F.; Beene, D.E. Jr.

1997-10-01

Results from a series of eight test fires ranging in size from 2.2 to 18.8 MW conducted aboard the Coast Guard fire test ship Mayo Lykes at Mobile, Alabama are presented and discussed. Tests aboard the break bulk type cargo ship consisted of heptane spray fires simulating engine room and galley fires, wood crib fires simulating cargo hold fires, and pool fires staged for comparison to land based regulatory fire results. Primary instrumentation for the tests consisted of two pipe calorimeters that simulated a typical package shape for radioactive materials packages

Experimental ship fire measurements with simulated radioactive cargo

International Nuclear Information System (INIS)

Koski, J.A.; Arvisol, M.; Bobbe, J.G.; Wix, S.D.; Cole, J.K.; Hohnstreiter, G.F.; Wix, S.D.; Beene, D.E.; Keane, M.P.

1998-01-01

Results from a series of eight test fires ranging in size from 2.2 to 18.8 MW conducted aboard the Coast Guard fire test ship Mayo Lykes at Mobile, Alabama are presented and discussed. Tests aboard the break-bulk type cargo ship consisted of heptane spray fires simulating engine room and galley fires, wood crib fires simulating cargo hold fires, and pool fires staged for comparison to land-based regulatory fire results. Primary instrumentation for the tests consisted of two pipe calorimeters that simulated a typical package shape for radioactive materials packages. (authors)

Production Balance of Ship Erection

Institute of Scientific and Technical Information of China (English)

JIANG Ru-hong; TAN Jia-hua; LIU Cun-gen

2008-01-01

A network plan model of ship erection was established based on the network planning technologyand the work-package breakdown system. The load-oriented production control method was introduced to buildup a throughput diagram model thus it is possible to describe the ship erection process numerically. Based onthe digitaiized models some cases of production balance of ship erection were studied and three balance indexeswere put forward, they are the load balance rate, the input manpower balance rate and the maximum gantrycrane operating times. Such an analytic method based on the balance evaluation is the important foundationfor digitization and intelligentization of shipyard production management.

Greater-than-Class C low-level radioactive waste shipping package/container identification and requirements study. National Low-Level Waste Management Program

Energy Technology Data Exchange (ETDEWEB)

Tyacke, M.

1993-08-01

This report identifies a variety of shipping packages (also referred to as casks) and waste containers currently available or being developed that could be used for greater-than-Class C (GTCC) low-level waste (LLW). Since GTCC LLW varies greatly in size, shape, and activity levels, the casks and waste containers that could be used range in size from small, to accommodate a single sealed radiation source, to very large-capacity casks/canisters used to transport or dry-store highly radioactive spent fuel. In some cases, the waste containers may serve directly as shipping packages, while in other cases, the containers would need to be placed in a transport cask. For the purpose of this report, it is assumed that the generator is responsible for transporting the waste to a Department of Energy (DOE) storage, treatment, or disposal facility. Unless DOE establishes specific acceptance criteria, the receiving facility would need the capability to accept any of the casks and waste containers identified in this report. In identifying potential casks and waste containers, no consideration was given to their adequacy relative to handling, storage, treatment, and disposal. Those considerations must be addressed separately as the capabilities of the receiving facility and the handling requirements and operations are better understood.

Safety analysis report: packages. LP-50 tritium package (packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Gates, A.A.; McCarthy, P.G.; Edl, J.W.

1975-04-01

Elemental tritium is shipped at low pressure in a stainless steel container (LP-50) sealed within an aluminum vessel and surrounded by a minimum of 4-in. thick Celotex insulation in a steel drum. The structural, thermal, containment, shielding, and criticality safety aspects of this package are evaluated. Procedures for loading and unloading, empty cask transport, acceptance testing and maintenance, and quality assurance requirements for the LP-50 package are described in detail. (U.S.)

Safety analysis report; packages LP-50 tritium package. (Packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Gates, A.A.; McCarthy, P.G.; Edl, J.W.; Chalfant, G.G.

1975-05-01

Elemental tritium is shipped at low pressure in a stainless steel container (LP-50) surrounded by an aluminum vessel and Celotex insulation at least 4 in. thick in a steel drum. The total weight of the package is 260 lbs maximum. The various components that constitute the package are described and are shown in 7 figures. The safety analysis includes: structural evaluations; thermal evaluations; containment; operating procedures; acceptance tests and maintenance program; and design review

Reflective Packaging

Science.gov (United States)

1994-01-01

The aluminized polymer film used in spacecraft as a radiation barrier to protect both astronauts and delicate instruments has led to a number of spinoff applications. Among them are aluminized shipping bags, food cart covers and medical bags. Radiant Technologies purchases component materials and assembles a barrier made of layers of aluminized foil. The packaging reflects outside heat away from the product inside the container. The company is developing new aluminized lines, express mailers, large shipping bags, gel packs and insulated panels for the building industry.

Y-12 defense programs. Nuclear Packaging Systems testing capabilities

International Nuclear Information System (INIS)

1995-06-01

The Nuclear Packaging Systems (NPS) Department can manage/accomplish any packaging task. The NPS organization is responsible for managing the design, testing, certification, procurement, operation, refurbishment, maintenance, and disposal of packaging used to transport radioactive materials, other hazardous materials, and general cargoes on public roads and within the Oak Ridge Y-12 Plant. Additionally, the NPS Department has developed a Quality Assurance plan for all packaging, design and procurement of nonweapon shipping containers for radioactive materials, and design and procurement of performance-oriented packaging for hazardous materials. Further, the NPS Department is responsible for preparation and submittal of Safety Analysis Reports for Packaging (SARP). The NPS Department coordinates shipping container procurement and safety certification activities that have lead-times of up to two years. A Packaging Testing Capabilities Table at the Oak Ridge complex is included as a table

Safety evaluation report for packaging (onsite) concrete-lined waste packaging

International Nuclear Information System (INIS)

Romano, T.

1997-01-01

The Pacific Northwest National Laboratory developed a package to ship Type A, non-transuranic, fissile excepted quantities of liquid or solid radioactive material and radioactive mixed waste to the Central Waste Complex for storage on the Hanford Site

Safety Analysis Report for Packaging (SARP): ATMX-500 Railcar nuclear packaging

International Nuclear Information System (INIS)

Griffin, J.F.; Peterson, J.B.; Edling, D.A.; Blauvelt, R.K.

1977-01-01

A Safety Analysis Report for Packaging (SARP) is described that makes available to all potential users the technical specifications and limits pertinent to the modification and use of the ATMX Railcars for which the Department of Transportation has issued Special Permit No. 5948. The SARP includes discussions of structural integrity, thermal resistance, radiation shielding and radiological safety, nuclear criticality safety, and quality control. Much of the information was previously published in a similar report. A complte physical and technical description of the package is presented. The packaging cnsists of a specially modified ATMX Series 500 Railcar loaded with DOT Specification steel drums or fiberglass coated plywood boxes. The results of the nuclear criticality safety analysis provide the maximum quantities of each fissile isotope which may be shipped as Fissile Class I in 30- and 55-gal drums. A limit of 5 g/ft 3 was established for wooden boxes. Design and development considerations regarding the packaging concept and modification of the ATMX-500 Railcar are presented. Tables, dimensional sketches, sequential photographs of the structural modifications, technical references, loading and shipping guidelines, and results of Mound Laboratory's experience in using this container are included. An internal review of this SARP was performed in compliance with the requirements of ERDA Manual Chapter 5201-Part V

System certification: An alternative to package certification?

International Nuclear Information System (INIS)

Luna, R.E.; Jefferson, R.J.

1992-01-01

One precept of the current radioactive material transportation regulations is that the package is the primary protection for the public. A packaging is chosen to provide containment, shielding, and criticality control suitable to the quantity and characteristics of the radionuclide being transported. Occasionally, radioactive materials requiring transport are not of a mass or size that would allow the materials to be shipped in an appropriate packaging. This is a particular problem for materials that should be shipped in a Type B package, but because such packages are designed and certified for specific contents, the package is usually fairly expensive, available in relatively small numbers, and often requires a fairly long period to achieve certification or amended certification for new contents. Where the shipment to be made is relatively infrequent, there may be economic and time penalties that may hamper shipment or force the shipper into uneconomic or high risk options. However, there is recognition of such situations in the International Atomic Energy Agency (IAEA) regulations under the provisions for Special Arrangement

Influence of non-radioactive payload parameters on radioactive shipping packages

International Nuclear Information System (INIS)

Drez, P.E.; Murthy, D.V.S.; Temus, C.J.; Quinn, G.J.; Ozaki, C.

1989-01-01

The transport of radioactive waste materials in radioactive material (RAM) packages involves two components: the packaging used for transportation, and the waste which forms the payload. The payload is usually comprised of non-radioactive materials contaminated with radionuclides. The non-radionuclide payload characteristics can often be a controlling factor in determining the restrictions imposed on the certification of the package. This paper describes these package/payload interactions and the limiting parameters for the Transuranic Package Transporter-II (TRUPACT-II), designed for the transportation of Contact Handled Transuranic (CH-TRU) waste. The parameters discussed include the physical and chemical form of the payload, the configuration of the waste, and resulting gas generation and gas release phenomena. Brief descriptions of the TRUPACT-II package and its payload are presented initially

Layered packaging: A synergistic method of transporting radioactive material

International Nuclear Information System (INIS)

Hohmann, G.L.

1989-01-01

The DOE certification for a transportation cask used to ship radioactive Krypton 85 from the Idaho Chemical Processing Plant (ICPP) to Oak Ridge National Laboratory (ORNL), was allowed to expire in 1987. The Westinghouse Idaho Nuclear Company (WINCO) was charged by DOE with modifying this cask to meet all current NRC requirements and preparing an updated Safety Analysis Report for Packaging, which would be submitted by DOE to the NRC for certification. However, an urgent need arose for ORNL to receive Krypton 85 which was in storage at the ICPP, which would not allow time to obtain certification of the modified shipping cask. WINCO elected to use a layered shipping configuration in which the gaseous Krypton 85 was placed in the uncertified, modified shipping cask to make use of its shielding and thermal insulation properties. This cask was then inserted into the Model No. 6400 (Super Tiger) packaging using a specially constructed plywood box and polyurethane foam dunnage. Structural evaluations were completed to assure the Super Tiger would provide the necessary impact, puncture, and thermal protection during maximum credible accidents. Analyses were also completed to determine the uncertified Krypton shipping cask would provide the necessary containment and shielding for up to 3.7 E+14 Bq of Krypton 85 when packaged inside the Super Tiger. The resulting reports, based upon this layered packaging concept, were adequate to first obtain DOE certification for several restricted shipments of Krypton 85 and then NRC certification for unrestricted shipments

Estimates of fire environments in ship holds containing radioactive material packages

International Nuclear Information System (INIS)

Koski, J.A.; Cole, J.K.; Hohnstreiter, G.F.; Wix, S.D.

1995-01-01

Fire environments that occur on cargo ships differ significantly from the fire environments found in land transport. Cargo ships typically carry a large amount of flammable fuel for propulsion and shipboard power, and may transport large quantities of flammable cargo. As a result, sea mode transport accident records contain instances of long lasting and intense fires. Since Irradiated Nuclear Fuel (INF) casks are not carried on tankers with large flammable cargoes, most of these dramatic, long burning fires are not relevant threats, and transport studies must concentrate on those fires that are most likely to occur. By regulation, INF casks must be separated from flammable cargoes by a fire-resistant, liquid-tight partition. This makes a fire in an adjacent ship hold the most likely fire threat. The large size of a cargo ship relative to any spent nuclear fuel casks on board, however, may permit a severe, long lasting fire to occur with little or no thermal impact on the casks. Although some flammable materials such as shipping boxes or container floors may exist in the same hold with the cask, the amount of fuel available may not provide a significant threat to the massive transport casks used for radioactive materials. This shipboard fire situation differs significantly from the regulatory conditions specified in 10 CFR 71 for a fully engulfing pool fire. To learn more about the differences, a series of simple thermal analyses has been completed to estimate cask behavior in likely marine and land thermal accident situations. While the calculations are based on several conservative assumptions, and are only preliminary, they illustrate that casks are likely to heat much more slowly in shipboard hold fires than in an open pool fire. The calculations also reinforce the basic regulatory concept that for radioactive materials, the shipping cask, not the ship, is the primary protection barrier to consider

Safety Evaluation for Packaging 101-SY Hydrogen Mitigation Mixer Pump package

International Nuclear Information System (INIS)

Carlstrom, R.F.

1994-01-01

This Safety Evaluation for Packaging (SEP) provides analysis and considered necessary to approve a one-time transfer of the 101-SY Hydrogen Mitigation Mixer Pump (HMMP). This SEP will demonstrate that the transfer of the HMMP in a new shipping container will provide an equivalent degree of safety as would be provided by packages meeting US Department of Transportation (DOT)/US Nuclear Regulatory Commission (NRC) requirements. This fulfills onsite, transportation requirements implemented by WHC-CM-2-14

Safety Evaluation for Packaging 101-SY Hydrogen Mitigation Mixer Pump package

Energy Technology Data Exchange (ETDEWEB)

Carlstrom, R.F.

1994-10-05

This Safety Evaluation for Packaging (SEP) provides analysis and considered necessary to approve a one-time transfer of the 101-SY Hydrogen Mitigation Mixer Pump (HMMP). This SEP will demonstrate that the transfer of the HMMP in a new shipping container will provide an equivalent degree of safety as would be provided by packages meeting US Department of Transportation (DOT)/US Nuclear Regulatory Commission (NRC) requirements. This fulfills onsite, transportation requirements implemented by WHC-CM-2-14.

Spallation impact analysis of plutonium storage container at K-Area

International Nuclear Information System (INIS)

Gong, C.

2000-01-01

A 100-pound concrete block falls 55-foot from ceiling spallation upon the top of the 9975 shipping package. This finite element analysis aims to evaluate the dynamic impact from the spallation upon the packaging. The geometric configuration of the packaging is meticulously modeled in detail. However, the drum is eliminated and the fiberboard with radius greater than 5.6 inches is conservatively omitted. The primary containment vessel and 3013 container were not included to simplify the model. The concrete block is modeled as a rigid body. The material properties are conservatively selected. The final results indicate that the secondary containment vessel is intact during this spallation impact. Consequently the primary containment vessel and 3013 container would not experience damage and containment is maintained. The secondary containment vessel protects the primary containment vessel from the dynamic impact. The top fiberboard is compressed from 3.5 inches to 0.875 inches will eventually recover to 1.8 inches according to tests performed at Savannah River Technology Center (SRTC)

Safety Evaluation for Packaging (onsite) T Plant Canyon Items

International Nuclear Information System (INIS)

OBRIEN, J.H.

2000-01-01

This safety evaluation for packaging (SEP) evaluates and documents the ability to safely ship mostly unique inventories of miscellaneous T Plant canyon waste items (T-P Items) encountered during the canyon deck clean off campaign. In addition, this SEP addresses contaminated items and material that may be shipped in a strong tight package (STP). The shipments meet the criteria for onsite shipments as specified by Fluor Hanford in HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments

Safety Evaluation for Packaging (onsite) T Plant Canyon Items

Energy Technology Data Exchange (ETDEWEB)

OBRIEN, J.H.

2000-07-14

This safety evaluation for packaging (SEP) evaluates and documents the ability to safely ship mostly unique inventories of miscellaneous T Plant canyon waste items (T-P Items) encountered during the canyon deck clean off campaign. In addition, this SEP addresses contaminated items and material that may be shipped in a strong tight package (STP). The shipments meet the criteria for onsite shipments as specified by Fluor Hanford in HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments.

Ship and Shoot

Science.gov (United States)

Woods, Ron

2012-01-01

Ron Woods shared incredibly valuable insights gained during his 28 years at the Kennedy Space Center (KSC) packaging Flight Crew Equipment for shuttle and ISS missions. In particular, Woods shared anecdotes and photos from various processing events. The moral of these stories and the main focus of this discussion were the additional processing efforts and effects related to a "ship-and-shoot" philosophy toward flight hardware.

Retrofit solutions for inland ships : The MoVe IT! approach

NARCIS (Netherlands)

Hekkenberg, R.G.; Thill, C.

2014-01-01

In MoVe IT!, a project in the European 7th framework package, it is investigated how existing European inland cargo ships can be retrofitted in order to improve their economic and environmental performance. In the project, experts from academia worked closely together with five ship owners to

Packaging and shipment of U.S. breeder reactor experiments

International Nuclear Information System (INIS)

Berger, J.D.

1980-01-01

Irradiation testing of fuels and materials in the Fast Test Reactor (FTR) required development of a shipping cask (designated T-3) and associated hardware for loading and shipping of these experiments to postirradiation examination facilities. The T-3 shipping-cask program included design, fabrication, and testing of internal cask packages to protect the experiments during loading, shipping, and unloading. The cask was designed for loading in both the vertical and horizontal attitudes

What is included with your online e-cigarette order? An analysis of e-cigarette shipping, product and packaging features.

Science.gov (United States)

Kong, Amanda Y; Derrick, Jason C; Abrantes, Anthony S; Williams, Rebecca S

2016-06-29

The electronic cigarette industry is growing, with youth using e-cigarettes at higher rates than they are using cigarettes, and retail and online sales projected to reach $10 billion in 2017. Minimal regulation of the production and marketing of e-cigarettes exists to date, which has allowed companies to promote unsupported claims. We assessed the shipping, product features and packaging of a wide variety of e-cigarettes purchased online by adults and youth. The most popular internet e-cigarette vendors were identified from a larger study of internet tobacco vendors. Between August 2013 and June 2014, adults made 56 purchase attempts from online vendors, and youth made 98 attempts. Packages received were assessed for exterior and internal packaging features, including product information, health warnings and additional materials. We analysed a total of 125 orders featuring 86 unique brands of e-cigarettes. The contents were rarely indicated on package exteriors. Product information came with just 60% of orders and just 38.4% included an instruction manual. Only 44.6% of products included a health warning, and some had unsupported claims, such as lack of secondhand smoke exposure. Additionally, some products were leaking e-liquid and battery fluid on arrival. A large variety of e-cigarette products are manufactured and marketed to consumers. Many products do not include instructions for use, and unsupported claims are being presented to consumers. Effective federal regulation of the manufacturing, packaging, product information and health claims surrounding e-cigarettes is necessary to ensure consumers are presented with accurate e-cigarette use information. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

New Packaging for Amplifier Slabs

Energy Technology Data Exchange (ETDEWEB)

Riley, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thorsness, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Suratwala, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Steele, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Rogowski, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-03-18

The following memo provides a discussion and detailed procedure for a new finished amplifier slab shipping and storage container. The new package is designed to maintain an environment of <5% RH to minimize weathering.

The merchant shipping (dangerous goods) (amendment) rules 1980 No. 789

International Nuclear Information System (INIS)

1980-01-01

These Rules amend the Merchant Shipping Rules 1978 and revoke the Merchant Shipping (Dangerous Goods) (Amendment) Rules 1979. The purpose of this amendment is to update the references to the 1978 Report of the Department of Trade's Standing Advisory Committee on the Carriage of Dangerous Goods in Ships (the Blue Book) and the 1977 Edition of the International Maritime Dangerous Goods Code of IMCO (the IMDG Code), referred to in the 1978 Rules. The amendments concern, inter alia, marking of packages on board ship which contain dangerous goods, including radioactive materials (NEA) [fr

Packaged low-level waste verification system

Energy Technology Data Exchange (ETDEWEB)

Tuite, K.; Winberg, M.R.; McIsaac, C.V. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1995-12-31

The Department of Energy through the National Low-Level Waste Management Program and WMG Inc. have entered into a joint development effort to design, build, and demonstrate the Packaged Low-Level Waste Verification System. Currently, states and low-level radioactive waste disposal site operators have no method to independently verify the radionuclide content of packaged low-level waste that arrives at disposal sites for disposition. At this time, the disposal site relies on the low-level waste generator shipping manifests and accompanying records to ensure that low-level waste received meets the site`s waste acceptance criteria. The subject invention provides the equipment, software, and methods to enable the independent verification of low-level waste shipping records to ensure that the site`s waste acceptance criteria are being met. The objective of the prototype system is to demonstrate a mobile system capable of independently verifying the content of packaged low-level waste.

Case study for one-piece removal method of reactor vessel of nuclear ship 'Mutsu'

International Nuclear Information System (INIS)

Nagane, Satoru; Kitahara, Katsumi; Yoshikawa, Seiji; Miyasaka, Yasuhiko; Fukumura, Nobuo; Nisizawa, Ichiou

2010-01-01

A reactor installed at the center part of the nuclear ship 'Mutsu' has been stored safely and exhibited in a reactor room building since 1996. The reactor vessel and its internals are key components because of main radioactive wastes for the reasonable decommissioning plan in the future. This report describes the one-piece removal method as the one package of the reactor vessel with its internals intact with a shipping container or additional shields. The reactor vessel package (Max.100ton) will be classified acceptable for burial at the low level radioactive waste (LLW), which will be buried at a LLW pit facility under waste disposal regulations. And also, the package will be classified as an IP-2-equivalent package according to the requirement for Shipments and Packagings. (author)

Packaging and transportation manual. Chapter on the packaging and transportation of hazardous and radioactive waste

International Nuclear Information System (INIS)

1998-03-01

The purpose of this chapter is to outline the requirements that Los Alamos National Laboratory employees and contractors must follow when they package and ship hazardous and radioactive waste. This chapter is applied to on-site, intra-Laboratory, and off-site transportation of hazardous and radioactive waste. The chapter contains sections on definitions, responsibilities, written procedures, authorized packaging, quality assurance, documentation for waste shipments, loading and tiedown of waste shipments, on-site routing, packaging and transportation assessment and oversight program, nonconformance reporting, training of personnel, emergency response information, and incident and occurrence reporting. Appendices provide additional detail, references, and guidance on packaging for hazardous and radioactive waste, and guidance for the on-site transport of these wastes

Packaging and transportation manual. Chapter on the packaging and transportation of hazardous and radioactive waste

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this chapter is to outline the requirements that Los Alamos National Laboratory employees and contractors must follow when they package and ship hazardous and radioactive waste. This chapter is applied to on-site, intra-Laboratory, and off-site transportation of hazardous and radioactive waste. The chapter contains sections on definitions, responsibilities, written procedures, authorized packaging, quality assurance, documentation for waste shipments, loading and tiedown of waste shipments, on-site routing, packaging and transportation assessment and oversight program, nonconformance reporting, training of personnel, emergency response information, and incident and occurrence reporting. Appendices provide additional detail, references, and guidance on packaging for hazardous and radioactive waste, and guidance for the on-site transport of these wastes.

Performance-oriented packaging: A guide to identifying, procuring, and using. Procurement and use of packaging using HM-181 regulations

International Nuclear Information System (INIS)

1994-09-01

This document addresses procurement of nonbulk packaging used for nonradioactive, hazardous materials that are transported by highway. The basic procedure is the same when making shipments by other modes. However, other sections of the regulations may affect the packaging requirements when shipping by other modes. The variation in requirements is extensive when air transportation is selected. A packaging engineer or transportation specialist should be contacted for guidance wen transport is by a mode other than highway

SHIPPING OF RADIOACTIVE ITEMS

CERN Multimedia

TIS/RP Group

2001-01-01

The TIS-RP group informs users that shipping of small radioactive items is normally guaranteed within 24 hours from the time the material is handed in at the TIS-RP service. This time is imposed by the necessary procedures (identification of the radionuclides, determination of dose rate, preparation of the package and related paperwork). Large and massive objects require a longer procedure and will therefore take longer.

Ship's Serviceman Laundry Handbook: Rate Training Manual and Non-Resident Career Course.

Science.gov (United States)

Naval Education and Training Command, Pensacola, FL.

The manual and course form a self study package that enables laundrymen to fulfill the requirements of the Ship's Serviceman (Laundry) rating. Chapter 1 provides information regarding the administration of ship's service activities (equipment maintenance, supervisory responsibilities, and procurement of supplies). Chapters 2 through 12 cover the…

RH Packaging Operations Manual

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2003-01-01

This procedure provides operating instructions for the RH-TRU 72-B Road Cask, Waste Shipping Package. In this document, ''Packaging'' refers to the assembly of components necessary to ensure compliance with the packaging requirements (not loaded with a payload). ''Package'' refers to a Type B packaging that, with its radioactive contents, is designed to retain the integrity of its containment and shielding when subject to the normal conditions of transport and hypothetical accident test conditions set forth in 10 CFR Part 71. Loading of the RH 72-B cask can be done two ways, on the RH cask trailer in the vertical position or by removing the cask from the trailer and loading it in a facility designed for remote-handling (RH). Before loading the 72-B cask, loading procedures and changes to the loading procedures for the 72-B cask must be sent to CBFO at sitedocuments at wipp.ws for approval

Study of accident environment during sea transport of nuclear material: Analysis of an engine room fire on a purpose built ship. Annex 5

International Nuclear Information System (INIS)

Yamamoto, K.; Shibata, H.; Ouchi, Y.; Kitamura, T.; Ito, T.; Hohnstreiter, G.F.; Pierce, J.D.; Koski, J.A.; Dukart, R.J.

2001-01-01

The program goal was to show that the IAEA safe transport regulations adequately cover the thermal effects of an engine-room fire on plutonium transportation packages stowed aboard a purpose built ship. The packages are stored in transportation containers located in a cargo hold of the ship. This study addressed the heat transfer from an engine-room fire that could heat and evaporate water out of the water-filled bulkhead and the resulting temperature conditions around the packages and inside the packages near their elastomeric seals. This study was designed to estimate the thermal response of a plutonium package in the hold of a purpose built ship during a shipboard fire, and furthermore, to confirm the sufficiency and adequacy of the current IAEA transport regulation

Development of methodology for certification of Type B shipping containers using analytical and testing techniques

International Nuclear Information System (INIS)

Sharp, R.R.; Varley, D.T.

1993-01-01

The use of multidisciplinary teams to develop Type B shipping containers improves the quality and reliability of these reusable packagings. Including the people involved in all aspects of the design, certification and use of the package leads to more innovative, user-friendly containers. Concurrent use of testing and analysis allows engineers to more fully characterize a shipping container's responses to the environments given in the regulations, and provides a strong basis for certification. The combination of the input and output of these efforts should provide a general methodology that designers of Type B radioactive material shipping containers can utilize to optimize and certify their designs. (J.P.N.)

DOE-EM-45 Packaging Operations And Maintenance Course

International Nuclear Information System (INIS)

Watkins, R.; England, J.

2010-01-01

Savannah River National Laboratory - Savannah River Packaging Technology (SRNL-SRPT) delivered the inaugural offering of the Packaging Operations and Maintenance Course for DOE-EM-45's Packaging Certification Program (PCP) at the University of South Carolina Aiken on September 1 and 2, 2009. Twenty-nine students registered, attended, and completed this training. The DOE-EM-45 Packaging Certification Program (PCP) sponsored the presentation of a new training course, Packaging Maintenance and Operations, on September 1-2, 2009 at the University of South Carolina Aiken (USC-Aiken) campus in Aiken, SC. The premier offering of the course was developed and presented by the Savannah River National Laboratory, and attended by twenty-nine students across the DOE, NNSA and private industry. This training informed package users of the requirements associated with handling shipping containers at a facility (user) level and provided a basic overview of the requirements typically outlined in Safety Analysis Report for Packaging (SARP) Chapters 1, 7, and 8. The course taught packaging personnel about the regulatory nature of SARPs to help reduce associated and often costly packaging errors. Some of the topics covered were package contents, loading, unloading, storage, torque requirements, maintaining records, how to handle abnormal conditions, lessons learned, leakage testing (including demonstration), and replacement parts. The target audience for this course was facility operations personnel, facility maintenance personnel, and field quality assurance personnel who are directly involved in the handling of shipping containers. The training also aimed at writers of SARP Chapters 1, 7, and 8, package designers, and anyone else involved in radioactive material packaging and transportation safety. Student feedback and critiques of the training were very positive. SRNL will offer the course again at USC Aiken in September 2010.

Littoral Combat Ship: Need to Address Fundamental Weaknesses in LCS and Frigate Acquisition Strategies

Science.gov (United States)

2016-06-01

LITTORAL COMBAT SHIP Need to Address Fundamental Weaknesses in LCS and Frigate Acquisition Strategies Report to...Office Highlights of GAO-16-356, a report to congressional committees June 2016 LITTORAL COMBAT SHIP Need to Address Fundamental Weaknesses in...capabilities of the LCS—a small surface combatant (SSC) consisting of a ship and reconfigurable mission packages built by two shipyards as different

Proposal of guidelines for selecting optimum options in packagings and transportation systems of spent fuel

International Nuclear Information System (INIS)

Saegusa, T.; Abe, H.; Fukuda, S.

1983-01-01

Type and size of spent fuel shipping packagings and packaging transport ships in spent fuel transport system would have been determined separately in response to technical requirements etc. of reactor sites and reprocessing plants. However, since more and more spent fuel will be generated from world's nuclear power plants and will be transported much frequently to reprocessing plants or storage facilities, the current spent fuel transport system will have to be necessarily reexamined from the operational and economical aspects or an optimum transport system may have to be newly determined in the near future. In the literature, a variety of options are found, particularly of spent fuel packagings. This paper listed and classified options of spent fuel packagings and packaging transport ships in the transportation systems of spent fuel on the basis of literature surveys. These options were discussed from viewpoints of designers and users and compared in terms of transport efficiency. Finally, one way to determine an optimum transport system of spent fuel was indicated considering the total transport system in the light of safety, operational efficiency and economy

Development of methodology for certification of Type B shipping containers using analytical and testing techniques

International Nuclear Information System (INIS)

Sharp, R.R.; Varley, D.T.

1992-01-01

The Analysis and Testing Group (WX-11) of the Design Engineering Division at Los Alamos National Laboratory (LANL) is developing methodology for designing and providing a basis for certification of Type B shipping containers. This methodology will include design, analysis, testing, fabrication, procurement, and obtaining certification of the Type B containers, allowing usage in support of the United States Department of Energy programs. While all aspects of the packaging development are included in this methodology, this paper focuses on the use of analysis and testing techniques for enhancing the design and providing a basis for certification. This methodology is based on concurrent engineering principles. Multidisciplinary teams within LANL are responsible for the design and certification of specific Type B Radioactive Material Shipping Containers. These teams include personnel with the various backgrounds and areas of expertise required to support the design, testing, analysis and certification tasks. To demonstrate that a package can pass all the performance requirements, the design needs to be characterized as completely as possible. Understanding package responses to the various environments and how these responses influence the effectiveness of the packaging requires expertise in several disciplines. In addition to characterizing the shipping container designs, these multidisciplinary teams should be able to provide insight into improving new package designs

Ressenya a Grifoll, Isabel, Julián Acebrón, Flocel Sabaté (eds. (2014: Cartografies de l’ànima. Identitat, memòria i escriptura, Lleida, Pagès Editors, 2014, 248 pàgs. ISBN:978-84-9975-517-5; i Acebrón, Julián, Isabel Grifoll, Flocel Sabaté (eds. (2015: La Construcció d’identitats imaginades. Literatura medieval i ideologia, Lleida, Pagès Editors, 2015, 320 pàgs. ISBN:978-84-9975-704-9

Directory of Open Access Journals (Sweden)

Vicent Martines

2016-12-01

Full Text Available Review to Grifoll, Isabel, Julián Acebrón, Flocel Sabaté (eds. (2014: Cartografies de l’ànima. Identitat, memòria i escriptura, Lleida, Pagès Editors, 2014, 248 pàgs. ISBN:978-84-9975-517-5; and Acebrón, Julián, Isabel Grifoll, Flocel Sabaté (eds. (2015: La Construcció d’identitats imaginades. Literatura medieval i ideologia, Lleida, Pagès Editors, 2015, 320 pàgs. ISBN:978-84-9975-704-9

FFTF railroad tank car Safety Evaluation for Packaging

International Nuclear Information System (INIS)

Carlstrom, R.F.

1995-01-01

This Safety Evaluation for Packaging (SEP) provides evaluations considered necessary to approve transfer of the 8,000 gallon Liquid Waste Tank Car (LWTC) from Fast Flux Test Facility (FFTF) to the 200 Areas. This SEP will demonstrate that the transfer of the LWTC will provide an equivalent degree of safety as would be provided by packages meeting U.S. Department of Transportation (DOT) requirements. This fulfills onsite transportation requirements implemented in the Hazardous Material Packaging and Shipping, WHC-CM-2-14

Safety analysis report for packaging (onsite) Castor GSF cask

International Nuclear Information System (INIS)

Clements, E.P.

1997-01-01

The CASTOR GSF packaging was designed and fabricated to be a certified Type B(U) packaging and comply with the requirements of the International Atomic Energy Agency (IAEA) for transport of up to five sealed canisters of vitrified radioactive materials. This onsite Safety Analysis Report for Packaging (SARP) provides the analysis and evaluations necessary to demonstrate that the casks, with the canister payload, meet the intent of the Type B packaging regulations set forth in 10 CFR 71 and therefore meet the onsite transportation safety requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping

Determination of Fire Enviroment in Stacked Cargo Containers with Radioactive Materials Packages

Energy Technology Data Exchange (ETDEWEB)

Arviso, M.; Bobbe, J.G.; Dukart, R.D.; Koski, J.A.

1999-05-01

Results from a Fire Test with a three-by-three stack of standard 6 m long International Standards Organization shipping containers containing combustible fuels and empty radioactive materials packages are reported and discussed. The stack is intended to simulate fire conditions that could occur during on-deck stowage on container cargo ships. The fire is initated by locating the container stack adjacent to a 9.8 x 6 m pool fire. Temperatures of both cargoes (empty and simulated radioactive materials packages) and containers are recorded and reported. Observations on the duration, intensity and spread of the fire are discussed. Based on the results, models for simulation of fire exposure of radioactive materials packages in such fires are suggested.

Savannah River Site Eastern Transportation Hub: A Concept For a DOE Eastern Packaging, Staging and Maintenance Center - 13143

International Nuclear Information System (INIS)

England, Jeffery L.; Adams, Karen; Maxted, Maxcine; Ruff Jr, Clarence; Albenesius, Andrew; Bowers, Mark D.; Fountain, Geoffrey; Hughes, Michael; Gordon, Sydney; O'Connor, Stephen

2013-01-01

The Department of Energy (DOE) is working to de-inventory sites and consolidate hazardous materials for processing and disposal. The DOE administers a wide range of certified shipping packages for the transport of hazardous materials to include Special Nuclear Material (SNM), radioactive materials, sealed sources and radioactive wastes. A critical element to successful and safe transportation of these materials is the availability of certified shipping packages. There are over seven thousand certified packagings (i.e., Type B/Type AF) utilized within the DOE for current missions. The synergistic effects of consolidated maintenance, refurbishment, testing, certification, and costing of these services would allow for efficient management of the packagings inventory and to support anticipated future in-commerce shipping needs. The Savannah River Site (SRS) receives and ships radioactive materials (including SNM) and waste on a regular basis for critical missions such as consolidated storage, stabilization, purification, or disposition using H-Canyon and HB-Line. The Savannah River National Laboratory (SRNL) has the technical capability and equipment for all aspects of packaging management. SRS has the only active material processing facility in the DOE complex and is one of the sites of choice for nuclear material consolidation. SRS is a logical location to perform maintenance and periodic testing of the DOE fleet of certified packagings. This initiative envisions a DOE Eastern Packaging Staging and Maintenance Center (PSMC) at the SRS and a western hub at the Nevada National Security Site (NNSS), an active DOE Regional Disposal Site. The PSMC's would be the first place DOE would go to meet their radioactive packaging needs and the primary locations projects would go to disposition excess packaging for beneficial reuse. These two hubs would provide the centralized management of a packaging fleet rather than the current approach to design, procure, maintain and dispose

Type B Drum packages

International Nuclear Information System (INIS)

Edwards, W.S.

1995-11-01

The Type B Drum package is a container in which a single drum containing Type B quantities of radioactive material will be packaged for shipment. The Type B Drum containers are being developed to fill a void in the packaging and transportation capabilities of the US Department of Energy (DOE), as no double containment packaging for single drums of Type B radioactive material is currently available. Several multiple-drum containers and shielded casks presently exist. However, the size and weight of these containers present multiple operational challenges for single-drum shipments. The Type B Drum containers will offer one unshielded version and, if needed, two shielded versions, and will provide for the option of either single or double containment. The primary users of the Type B Drum container will be any organization with a need to ship single drums of Type B radioactive material. Those users include laboratories, waste retrieval facilities, emergency response teams, and small facilities

ATMX-600 rail car safety analysis report for packaging (SARP)

International Nuclear Information System (INIS)

Adcock, F.E.; McCarthy, J.D.

1977-01-01

The ATMX-600 series rail car is used by Rockwell International, Rocky Flats Plant, for shipping low-level radioactive waste under the provisions of DOT Special Permit 5948. Fissile Class I shipments are authorized with the car loaded to capacity with drums containing up to 200 g of 239 Pu. Inner packaging may be polyethylene-lined steel drums or fiberglass-coated plywood crates. These massive double-walled steel cars provide the equivalent protection of a Type B package. Rapid loading and unloading of the 9- by 9- by 50-ft cargo space is accomplished by prepackaging the waste in standard 20-ft steel cargo containers. The ATMX-600 rail car will hold two cargo containers, each carrying seventy 55-gal drums and up to 44,800 lb gross weight. Improvements to inner packaging and current shipping practices are discussed

Development of Self-Remediating Packaging for Safe and Secure Transport of Infectious Substances.

Energy Technology Data Exchange (ETDEWEB)

Guilinger, Terry Rae; Gaudioso, Jennifer M; Aceto, Donato Gonzalo; Lowe, Kathleen M.; Tucker, Mark D; Salerno, Reynolds Mathewson; Souza, Caroline Ann

2006-11-01

As George W. Bush recognized in November 2001, "Infectious diseases make no distinctions among people and recognize no borders." By their very nature, infectious diseases of natural or intentional (bioterrorist) origins are capable of threatening regional health systems and economies. The best mechanism for minimizing the spread and impact of infectious disease is rapid disease detection and diagnosis. For rapid diagnosis to occur, infectious substances (IS) must be transported very quickly to appropriate laboratories, sometimes located across the world. Shipment of IS is problematic since many carriers, concerned about leaking packages, refuse to ship this material. The current packaging does not have any ability to neutralize or kill leaking IS. The technology described here was developed by Sandia National Laboratories to provide a fail-safe packaging system for shipment of IS that will increase the likelihood that critical material can be shipped to appropriate laboratories following a bioterrorism event or the outbreak of an infectious disease. This safe and secure packaging method contains a novel decontaminating material that will kill or neutralize any leaking infectious organisms; this feature will decrease the risk associated with shipping IS, making transport more efficient. 3 DRAFT4

Test plan/procedure for the SPM-1 shipping container system. Revision 0

International Nuclear Information System (INIS)

Flanagan, B.D.

1995-01-01

The 49 CFR 173.465 Type A packaging tests will verify that SPM-1 will provide adequate protection and pass as a Type A package. Test will determine that the handle of the Pig will not penetrate through the plywood spacer and rupture the shipping container. Test plan/procedure provides planning, pre-test, setup, testing, and post-testing guidelines and procedures for conducting the open-quotes Free Drop Testclose quotes procedure for the SPM-1 package

ATMX-600 rail car safety analysis report for packaging (SARP)

International Nuclear Information System (INIS)

Adcock, F.E.; McCarthy, J.D.

1977-01-01

The ATMX-600 series rail car is used by Rockwell International, Rocky Flats Plant, for shipping low-level radioactive waste under the provisions of DOT Special Permit 5948. Fissile Class I shipments are authorized with the car loaded to capacity with drums containing up to 200 grams of plutonium-239. Inner packaging may be polyethylene-lined steel drums or fiberglass-coated plywood crates. These massive double-walled steel cars provide the equivalent protection of a Type B package. Rapid loading and unloading of the 9- by 9- by 50-foot cargo space are accomplished by prepackaging the waste in standard 20-foot steel cargo containers. The ATMX-600 rail car will hold two cargo containers, each carrying seventy 55-gallon drums and up to 44,800 pounds gross weight. This report is a revision of an earlier document and describes improvements to inner packaging. It also reflects current shipping practices

Standardized analyses of nuclear shipping containers

International Nuclear Information System (INIS)

Parks, C.V.; Hermann, O.W.; Petrie, L.M.; Hoffman, T.J.; Tang, J.S.; Landers, N.F.; Turner, W.D.

1983-01-01

This paper describes improved capabilities for analyses of nuclear fuel shipping containers within SCALE -- a modular code system for Standardized Computer Analyses for Licensing Evaluation. Criticality analysis improvements include the new KENO V, a code which contains an enhanced geometry package and a new control module which uses KENO V and allows a criticality search on optimum pitch (maximum k-effective) to be performed. The SAS2 sequence is a new shielding analysis module which couples fuel burnup, source term generation, and radial cask shielding. The SAS5 shielding sequence allows a multidimensional Monte Carlo analysis of a shipping cask with code generated biasing of the particle histories. The thermal analysis sequence (HTAS1) provides an easy-to-use tool for evaluating a shipping cask response to the accident capability of the SCALE system to provide the cask designer or evaluator with a computational system that provides the automated procedures and easy-to-understand input that leads to standarization

Thermal analysis of RFETS SS and C

International Nuclear Information System (INIS)

Korinko, P.S.

2000-01-01

In support of the gas generation test program (GGTP) for the 9975 shipping container, thermogravimetric analysis (TGA) was conducted. The objective of this activity was to determine the moisture content as an input to the gas generation model

Documentation and analysis for packaging limited quantity ice chests

International Nuclear Information System (INIS)

Nguyen, P.M.

1995-01-01

The purpose of this Documentation and Analysis for Packaging (DAP) is to document that ice chests meet the intent of the International Air Transport Association (IATA) and the U.S. Department of Transportation (DOT) Code of Federal Regulations as strong, tight containers for the packaging of limited quantities for transport. This DAP also outlines the packaging method used to protect the sample bottles from breakage. Because the ice chests meet the DOT requirements, they can be used to ship LTD QTY on the Hanford Site

Spent fuel shipping costs for transportation logistics analyses

International Nuclear Information System (INIS)

Cole, B.M.; Cross, R.E.; Cashwell, J.W.

1983-05-01

Logistics analyses supplied to the nuclear waste management programs of the U.S. Department of Energy through the Transportation Technology Center (TTC) at Sandia National Laboratories are used to predict nuclear waste material logistics, transportation packaging demands, shipping and receiving rates and transportation-related costs for alternative strategies. This study is an in-depth analysis of the problems and contingencies associated with the costs of shipping irradiated reactor fuel. These costs are extremely variable however, and have changed frequently (sometimes monthly) during the past few years due to changes in capital, fuel, and labor costs. All costs and charges reported in this study are based on January 1982 data using existing transport cask systems and should be used as relative indices only. Actual shipping costs would be negotiable for each origin-destination combination

Savannah River Site Eastern Transportation Hub: A Concept For a DOE Eastern Packaging, Staging and Maintenance Center - 13143

Energy Technology Data Exchange (ETDEWEB)

England, Jeffery L. [Savannah River National Laboratory, Aiken, South Carolina (United States); Adams, Karen; Maxted, Maxcine; Ruff Jr, Clarence [U.S. Department of Energy, Savannah River Site, Aiken, SC (United States); Albenesius, Andrew; Bowers, Mark D.; Fountain, Geoffrey; Hughes, Michael [Savannah River Nuclear Solutions, Aiken, SC (United States); Gordon, Sydney [National Security Technologies, LLC, Las Vegas, NV (United States); O' Connor, Stephen [U.S. Department of Energy, HQ DOE, EM-33, Germantown MD (United States)

2013-07-01

The Department of Energy (DOE) is working to de-inventory sites and consolidate hazardous materials for processing and disposal. The DOE administers a wide range of certified shipping packages for the transport of hazardous materials to include Special Nuclear Material (SNM), radioactive materials, sealed sources and radioactive wastes. A critical element to successful and safe transportation of these materials is the availability of certified shipping packages. There are over seven thousand certified packagings (i.e., Type B/Type AF) utilized within the DOE for current missions. The synergistic effects of consolidated maintenance, refurbishment, testing, certification, and costing of these services would allow for efficient management of the packagings inventory and to support anticipated future in-commerce shipping needs. The Savannah River Site (SRS) receives and ships radioactive materials (including SNM) and waste on a regular basis for critical missions such as consolidated storage, stabilization, purification, or disposition using H-Canyon and HB-Line. The Savannah River National Laboratory (SRNL) has the technical capability and equipment for all aspects of packaging management. SRS has the only active material processing facility in the DOE complex and is one of the sites of choice for nuclear material consolidation. SRS is a logical location to perform maintenance and periodic testing of the DOE fleet of certified packagings. This initiative envisions a DOE Eastern Packaging Staging and Maintenance Center (PSMC) at the SRS and a western hub at the Nevada National Security Site (NNSS), an active DOE Regional Disposal Site. The PSMC's would be the first place DOE would go to meet their radioactive packaging needs and the primary locations projects would go to disposition excess packaging for beneficial reuse. These two hubs would provide the centralized management of a packaging fleet rather than the current approach to design, procure, maintain and

Surface contamination of hazardous drug pharmacy storage bins and pharmacy distributor shipping containers.

Science.gov (United States)

Redic, Kimberly A; Fang, Kayleen; Christen, Catherine; Chaffee, Bruce W

2018-03-01

Purpose This study was conducted to determine whether there is contamination on exterior drug packaging using shipping totes from the distributor and carousel storage bins as surrogate markers of external packaging contamination. Methods A two-part study was conducted to measure the presence of 5-fluorouracil, ifosfamide, cyclophosphamide, docetaxel and paclitaxel using surrogate markers for external drug packaging. In Part I, 10 drug distributor shipping totes designated for transport of hazardous drugs provided a snapshot view of contamination from regular use and transit in and out of the pharmacy. An additional two totes designated for transport of non-hazardous drugs served as controls. In Part II, old carousel storage bins (i.e. those in use pre-study) were wiped for snapshot view of hazardous drug contamination on storage bins. New carousel storage bins were then put into use for storage of the five tested drugs and used for routine storage and inventory maintenance activities. Carousel bins were wiped at time intervals 0, 8, 16 and 52 weeks to measure surface contamination. Results Two of the 10 hazardous shipping totes were contaminated. Three of the five-old carousel bins were contaminated with cyclophosphamide. One of the old carousel bins was also contaminated with ifosfamide. There were no detectable levels of hazardous drugs on any of the new storage bins at time 0, 8 or 16 weeks. However, at the Week 52, there was a detectable level of 5-FU present in the 5-FU carousel bin. Conclusions Contamination of the surrogate markers suggests that external packaging for hazardous drugs is contaminated, either during the manufacturing process or during routine chain of custody activities. These results demonstrate that occupational exposure may occur due to contamination from shipping totes and storage bins, and that handling practices including use of personal protective equipment is warranted.

Preparation of the Shippingport reactor pressure vessel shipping package

International Nuclear Information System (INIS)

Yannitell, D.M.

1988-01-01

Shippingport Station Decommissioning Project is the removal and shipment the Reactor Pressure Vessel (PRV) and its associated Neutron Shield Tank (NST) to the government owned Hanford Reservation in Richland, Washington. Engineering studies considered the alternatives for removal and shipment of the RPV/NST. These included segmentation for subsequent truck shipments, and one-piece removal with barge or rail shipment. Although the analysis indicated that current technology could be utilized to accomplish either alternative, one-piece removal of the RPV was selected as the safest, most cost effective method. When compared to segmentation, it was estimated that one-piece removal would reduce the duration of the Project by 1 year, reduce cost by $4 M, and result in a savings of radiation exposure of 150 man-Rem. Rail transportation of an integral RPV/NST package is not feasible due to the physical size of the package. 5 refs., 1 fig

Criticality safety evaluation of a type B enriched uranium shipping container

International Nuclear Information System (INIS)

Hopper, C.M.

1978-01-01

The Oak Ridge Y-12 Plant Model DT-14 container was developed to replace and extend the enriched uranium shipping capabilities of the USA/5765/BF Vermiculite shipping container. This work was accomplished to comply with the DOE Immediate Action Directive Number 0529-02 for ''Phasing out the use of loose or bagged Vermiculite packaging material as a thermal shield and shock absorber in radioactive material packages''. The Model DT-14 is fabricated from a Specification 17H 30-gallon drum, cane fiberboard insulation, and a steel inner containment vessel (159 mm dia by 390 mm height). The single-package and array analyses are based upon results of the multigroup Monte Carlo criticality program, KENO, utilizing 16-energy-group Hansen-Roach, and Knight modified 238 U cross sections. The program and cross sections are considered well established on the basis of their success in calculating a large variety of critical experiments. Validation results show that a calculated neutron multiplication factor plus two standard deviations equal to 0.970 or greater must be considered critical, and all lower values may be considered safe

Potential aerosol generation mechanisms from damaged shipping packages

International Nuclear Information System (INIS)

Mishima, J.

1976-07-01

Estimates of the potential airborne release of radioactive materials in transportation accidents are necessary to compare the safety in various shipping methods. To make such estimates, information is required on various aspects of the accident situation (physical and chemical characteristics of the source materials, forces/conditions imposed upon the source material by the accident, etc.). Published data which may be useful in estimating the fractional airborne release of radionuclides are discussed. Special emphasis is given to experimental data generated under conditions similar to those found under accident conditions. Estimates of the fractional airborne release of a liquid and a powder for particular accident scenarios are discussed to illustrate the application of the data

Conceptual design and development of high-activity radioactive liquid packaging (summary)

International Nuclear Information System (INIS)

Riley, D.L.; McCoy, J.C.; Edwards, W.S.

1994-08-01

Environmental remediation and disposal of US Department of Energy radioactive liquid waste require analytical support, characterization, process development, testing, demonstration, and stabilization. In support of these diverse activities, there is a need to transport varying quantities of Type B high-activity liquid (HAL). To date, except for quantities of 50 ml (1.7 oz), there has never been, a US, Nuclear Regulatory Commission-licensed liquid Type B package available to support these remediation activities. In an effort to develop suitable packaging for large volumes of HAL, an investigation into packaging alternatives that would facilitate such transfers is under way. In, past and present studies, a spent fuel shipping cask fitted with a high-integrity pressure vessel has been determined to be the most viable concept for large volume HAL shipments. One concept that was investigated utilized the Pacific Nuclear 125-B shipping container and has been shown to meet the strUctural, thermal, shielding, and criticality conditions for HAL. The results of these investigations are being extended to develop the concept into the HAL packaging system

Safety analysis report for packaging (SARP) of the Oak Ridge National Laboratory Garden Carrier No. 2

International Nuclear Information System (INIS)

Klima, B.B.; Shappert, L.B.; Seagren, R.D.; Box, W.D.

1978-04-01

An analytical evaluation of the Oak Ridge National Laboratory Garden Carrier No. 2 was made to demonstrate its compliance with the regulations governing off-site radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the cask complies with the applicable regulations. The package is designed to ship large quantities of fissile and radioactive materials as solids

Leaktightness definitions for and leakage tests on packages for the transport of radioactive materials

International Nuclear Information System (INIS)

Tanguy, L.

1989-07-01

In 1986, the International Organization for Standardization asked a group of experts representing some fifteen countries to draft a standard for the leaktightness of packagings used for the transport of radioactive materials. Progress of work and test before shipping of packages are reviewed

Transportation Packages to Support Savannah River Site Missions

International Nuclear Information System (INIS)

Opperman, E.

2001-01-01

The Savannah River Site's missions have expanded from primarily a defense mission to one that includes environmental cleanup and the stabilization, storage, and preparation for final disposition of nuclear materials. The development of packaging and the transportation of radioactive materials are playing an ever-increasing role in the successful completion of the site's missions. This paper describes the Savannah River Site and the three strategic mission areas of (1) nuclear materials stewardship, (2) environmental stewardship, and (3) nuclear weapons stockpile stewardship. The materials and components that need to be shipped, and associated packaging, will be described for each of the mission areas. The diverse range of materials requiring shipment include spent fuel, irradiated target assemblies, excess plutonium and uranium materials, high level waste canisters, transuranic wastes, mixed and low level wastes, and nuclear weapons stockpile materials and components. Since many of these materials have been in prolonged storage or resulted from disassembly of components, the composition, size and shape of the materials present packaging and certification challenges that need to be met. Over 30 different package designs are required to support the site's missions. Approximately 15 inbound shipping-legs transport materials into the Savannah River Site and the same number (15) of outgoing shipment-legs are carrying materials from the site for further processing or permanent disposal

IMPLEMENTATION APPROACHES DURING SIMULATION OF ENERGY PROCESSES FOR A DYNAMICALLY POSITIONED SHIP

Directory of Open Access Journals (Sweden)

V.V. Budashko

2015-12-01

Full Text Available Purpose. Creation of a mathematical model of the ship's power plant (SPP combined propulsion complexes (CPC that takes into account the behavior of all objects, including the ship itself, the transfer of power from the medium speed diesel generators on the propellers, which will allow to take into account the hydrodynamic properties of the vessel and their impact on the energy processes in SPP CPC. Methodology. The analysis of energy processes in the SPP CPC in different operating conditions resulted in creation of a strategy for constructing mathematical models of SPP CPC. This strategy is based on the implementation on the vector plane resulting power characteristics of SPP vectors disturbances, leading to the deviation of the hydrodynamic characteristics of the ship during operation dynamic positioning. The result allowed to consider not only the features of setting PID-governors of frequency converters of electric thrusters but the automatic voltage regulators of medium speed diesel generators as well. Results. Within the research work a software package Ships_CPC in MatLab/Simulink was developed under the state budget project «Concepts, technologies and ways of improving ship power plants combined propulsion complexes» at the Department of Electromechanics and Electrical Engineering of Odessa National Maritime Academy. Originality. This complex represents a set of functional blocks of the components SPP CPC, built on the principle of «input-output». The simulation results demonstrate the ability to use software package Ships_CPC to study the effect of various settings on the energy regulators of processes SPP CPC, which can develop and integrate the different strategies of automatic voltage regulators. Practical value. Since software complex Ships_CPC was developed under Open system technology, it can reorganize, re-tune and integrate in processes of any difficulties with further completion in the form of a universal structure.

Contribution of water vapor pressure to pressurization of plutonium dioxide storage containers

Science.gov (United States)

Veirs, D. Kirk; Morris, John S.; Spearing, Dane R.

2000-07-01

Pressurization of long-term storage containers filled with materials meeting the US DOE storage standard is of concern.1,2 For example, temperatures within storage containers packaged according to the standard and contained in 9975 shipping packages that are stored in full view of the sun can reach internal temperatures of 250 °C.3 Twenty five grams of water (0.5 wt.%) at 250 °C in the storage container with no other material present would result in a pressure of 412 psia, which is limited by the amount of water. The pressure due to the water can be substantially reduced due to interactions with the stored material. Studies of the adsorption of water by PuO2 and surface interactions of water with PuO2 show that adsorption of 0.5 wt.% of water is feasible under many conditions and probable under high humidity conditions.4,5,6 However, no data are available on the vapor pressure of water over plutonium dioxide containing materials that have been exposed to water.

Finite element analysis of container ship's cargo hold using ANSYS and POSEIDON software

Science.gov (United States)

Tanny, Tania Tamiz; Akter, Naznin; Amin, Osman Md.

2017-12-01

Nowadays ship structural analysis has become an integral part of the preliminary ship design providing further support for the development and detail design of ship structures. Structural analyses of container ship's cargo holds are carried out for the balancing of their safety and capacity, as those ships are exposed to the high risk of structural damage during voyage. Two different design methodologies have been considered for the structural analysis of a container ship's cargo hold. One is rule-based methodology and the other is a more conventional software based analyses. The rule based analysis is done by DNV-GL's software POSEIDON and the conventional package based analysis is done by ANSYS structural module. Both methods have been applied to analyze some of the mechanical properties of the model such as total deformation, stress-strain distribution, Von Mises stress, Fatigue etc., following different design bases and approaches, to indicate some guidance's for further improvements in ship structural design.

Safety Evaluation for Packaging for the N Reactor/single pass reactor fuel characterization shipments

International Nuclear Information System (INIS)

Stevens, P.F.

1994-01-01

The purpose of this Safety Evaluation for Packaging (SEP) is to authorize the ChemNuclear CNS 1-13G packaging to ship samples of irradiated fuel elements from the 100 K East and 100 K West basins to the Postirradiation Testing Laboratory (PTL) in support of the spent nuclear fuel characterization effort. It also authorizes the return of the fuel element samples to the 100 K East facility using the same packaging. The CNS 1-13G cask has been-chosen to transport the fuel because it has a Certificate of Compliance (CoC) issued by the US Nuclear Regulatory Commission (NRC) for transporting irradiated oxide and metal fuel in commerce. It is capable of being loaded and offloaded underwater and may be shipped with water in the payload compartment

Portable Radiation Package (PRP) Instrument Handbook

Energy Technology Data Exchange (ETDEWEB)

Reynolds, R Michael [Remote Measurements and Research Company, Seattle, WA (United States)

2017-08-03

The Portable Radiation Package (PRP) was developed to provide basic radiation information in locations such as ships at sea where proper exposure is remote and difficult, the platform is in motion, and azimuth alignment is not fixed. Development of the PRP began at Brookhaven National Laboratory (BNL) in the mid-1990s and versions of it were deployed on ships in the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Nauru-99 project. The PRP was deployed on ships in support of the National Aeronautics and Space Administration (NASA) Sensor Intercomparison for Marine Biological and Interdisciplinary Ocean Studies (SIMBIOS) program. Over the years the measurements have remained the same while the post-processing data analysis, especially for the FRSR, has evolved. This document describes the next-generation Portable Radiation Package (PRP2) that was developed for the DOE ARM Facility, under contract no. 9F-31462 from Argonne National Laboratory (ANL). The PRP2 has the same scientific principles that were well validated in prior studies, but has upgraded electronic hardware. The PRP2 approach is completely modular, both in hardware and software. Each sensor input is treated as a separate serial stream into the data collection computer. In this way the operator has complete access to each component of the system for purposes of error checking, calibration, and maintenance. The resulting system is more reliable, easier to install in complex situations, and more amenable to upgrade.

Strength Analysis on Ship Ladder Using Finite Element Method

Science.gov (United States)

Budianto; Wahyudi, M. T.; Dinata, U.; Ruddianto; Eko P., M. M.

2018-01-01

In designing the ship’s structure, it should refer to the rules in accordance with applicable classification standards. In this case, designing Ladder (Staircase) on a Ferry Ship which is set up, it must be reviewed based on the loads during ship operations, either during sailing or at port operations. The classification rules in ship design refer to the calculation of the structure components described in Classification calculation method and can be analysed using the Finite Element Method. Classification Regulations used in the design of Ferry Ships used BKI (Bureau of Classification Indonesia). So the rules for the provision of material composition in the mechanical properties of the material should refer to the classification of the used vessel. The analysis in this structure used program structure packages based on Finite Element Method. By using structural analysis on Ladder (Ladder), it obtained strength and simulation structure that can withstand load 140 kg both in static condition, dynamic, and impact. Therefore, the result of the analysis included values of safety factors in the ship is to keep the structure safe but the strength of the structure is not excessive.

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2005-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.

Documentation associated with the shipping of Hot-Cell Waste from WESF 225-B to the 200W (218-W-3AE) burial grounds under shipment number RSR-37338

International Nuclear Information System (INIS)

PAWLAK, M.W.

1998-01-01

The purpose of this report is to compile the records generated during the Packaging and Shipping of WESF Hot-Cell Waste from the 225-B Facility to 200W (218-W-3AE) burial grounds. A total of six 55-gallon drums were packaged and shipped using the Chem-Nuc Cask in accordance with WHC-SD-TP-SARP-025, Rev.0 ''Safety Analysis Report for Packaging (Onsite) for Type B Material in the CNS-14-215H Cask''

Safety evaluation for packaging (onsite) SERF cask

International Nuclear Information System (INIS)

Edwards, W.S.

1997-01-01

This safety evaluation for packaging (SEP) documents the ability of the Special Environmental Radiometallurgy Facility (SERF) Cask to meet the requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for transfer of Type B quantities (up to highway route controlled quantities) of radioactive material within the 300 Area of the Hanford Site. This document shall be used to ensure that loading, tie down, transport, and unloading of the SERF Cask are performed in accordance with WHC-CM-2-14. This SEP is valid until October 1, 1999. After this date, an update or upgrade to this document is required

Documentation and verification required for type A packaging use

Energy Technology Data Exchange (ETDEWEB)

O`Brien, J.H.

1997-07-30

This document furnishes knowledge and methods for verifying compliance with the U.S. Department of Transportation (DOT) packaging requirements for shipping Type A quantities of radioactive material. The primary emphasis is on the requirements identified in 49 CFR 173.415(a), which states, ``Each offeror of a Specification 7A package must maintain on file for at least one year after the shipment, and shall provide to DOT on request, complete documentation of tests and an engineering evaluation of comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification.`` This guidance document uses a checklist to show compliance.

Documentation and verification required for type A packaging use

International Nuclear Information System (INIS)

O'Brien, J.H.

1997-01-01

This document furnishes knowledge and methods for verifying compliance with the U.S. Department of Transportation (DOT) packaging requirements for shipping Type A quantities of radioactive material. The primary emphasis is on the requirements identified in 49 CFR 173.415(a), which states, ''Each offeror of a Specification 7A package must maintain on file for at least one year after the shipment, and shall provide to DOT on request, complete documentation of tests and an engineering evaluation of comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification.'' This guidance document uses a checklist to show compliance

National Bureau of Standards health physics radioactive material shipment survey, packaging, and labelling program under ICAO/IATA and DOT regulations

International Nuclear Information System (INIS)

Sharp, D.R.; Slaback, L.A.

1984-01-01

NBS routinely ships many radionuclides in small to moderate activities, with many shipments containing mixtures of radionuclides in a variety of combinations. The ICAO/IATA shipping regulations (and the new DoT regulations on their model) specify individual shipping parameters for every radionuclide. As a result, quality control in the shipment of these radioactive packages has become difficult to maintain. The authors have developed a computer program that will guide a Health Physics technician through package surveys and give exact packaging and labelling instructions. The program is a 27 kilobyte user-friendly BASIC program that runs on an Epson-HX20 notebook computer with microcassette drive and 16 kilobyte memory expansion unit. This small computer is more manageable than the regulation books for which it will be substituted and will be used in routine radioactive shipments

Study of the Accident Environment During Sea Transport of Nuclear Material: Analysis of an Engine-room Fire on a Purpose-built Ship (invited paper)

International Nuclear Information System (INIS)

Yamamoto, K.; Kitamura, T.; Shibata, K.; Ouchi, Y.; Ito, T.; Hohnstreiter, G.F.; Pierce, J.D.; Koski, J.A.; Dukart, R.K.

2000-01-01

The programme goal was to show that the IAEA safe transport regulations adequately cover the thermal effects of an engine-room fire on plutonium transport packages stowed aboard a purpose-built ship. The packages are stored in transport containers located in a cargo hold of the ship. For this study, it was assumed that the packages in No 5 hold, adjacent to an engine-room, could be subject to heating due to a fire in the engine-room. The No 5 hold and the engine-room are separated by a water-filled bulkhead. This study addressed the heat transfer from an engine-room fire that could heat and evaporate water out of the water-filled bulkhead and the resulting temperature conditions around the packages and inside the packages near their elastometric seals. (author)

The 9th international symposium on the packaging and transportation of radioactive materials

Energy Technology Data Exchange (ETDEWEB)

None

1989-06-01

This three-volume document contains the papers and poster sessions presented at the symposium. Volume 3 contains 87 papers on topics such as structural codes and benchmarking, shipment of plutonium by air, spent fuel shipping, planning, package design and risk assessment, package testing, OCRWN operations experience and regulations. Individual papers were processed separately for the data base. (TEM)

A review of a radioactive material shipping container including design, testing, upgrading compliance program and shipping logistics

International Nuclear Information System (INIS)

Celovsky, A.; Lesco, R.; Gale, B.; Sypes, J.

2003-01-01

Ten years ago Atomic Energy of Canada developed a Type B(U)-85 shipping container for the global transport of highly radioactive materials. This paper reviews the development of the container, including a summary of the design requirements, a review of the selected materials and key design elements, and the results of the major qualification tests (drop testing, fire test, leak tightness testing, and shielding integrity tests). As a result of the testing, improvements to the structural, thermal and containment design were made. Such improvements, and reasons thereof, are noted. Also provided is a summary of the additional analysis work required to upgrade the package from a Type B(U) to a Type B(F), i.e. essentially upgrading the container to include fissile radioisotopes to the authorized radioactive contents list. Having a certified shipping container is only one aspect governing the global shipments of radioactive material. By necessity the shipment of radioactive material is a highly regulated environment. This paper also explores the experiences with other key aspects of radioactive shipments, including the service procedures used to maintain the container certification, the associated compliance program for radioactive material shipments, and the shipping logistics involved in the transport. (author)

Severities of transportation accidents involving large packages

Energy Technology Data Exchange (ETDEWEB)

Dennis, A.W.; Foley, J.T. Jr.; Hartman, W.F.; Larson, D.W.

1978-05-01

The study was undertaken to define in a quantitative nonjudgmental technical manner the abnormal environments to which a large package (total weight over 2 tons) would be subjected as the result of a transportation accident. Because of this package weight, air shipment was not considered as a normal transportation mode and was not included in the study. The abnormal transportation environments for shipment by motor carrier and train were determined and quantified. In all cases the package was assumed to be transported on an open flat-bed truck or an open flat-bed railcar. In an earlier study, SLA-74-0001, the small-package environments were investigated. A third transportation study, related to the abnormal environment involving waterways transportation, is now under way at Sandia Laboratories and should complete the description of abnormal transportation environments. Five abnormal environments were defined and investigated, i.e., fire, impact, crush, immersion, and puncture. The primary interest of the study was directed toward the type of large package used to transport radioactive materials; however, the findings are not limited to this type of package but can be applied to a much larger class of material shipping containers.

Severities of transportation accidents involving large packages

International Nuclear Information System (INIS)

Dennis, A.W.; Foley, J.T. Jr.; Hartman, W.F.; Larson, D.W.

1978-05-01

The study was undertaken to define in a quantitative nonjudgmental technical manner the abnormal environments to which a large package (total weight over 2 tons) would be subjected as the result of a transportation accident. Because of this package weight, air shipment was not considered as a normal transportation mode and was not included in the study. The abnormal transportation environments for shipment by motor carrier and train were determined and quantified. In all cases the package was assumed to be transported on an open flat-bed truck or an open flat-bed railcar. In an earlier study, SLA-74-0001, the small-package environments were investigated. A third transportation study, related to the abnormal environment involving waterways transportation, is now under way at Sandia Laboratories and should complete the description of abnormal transportation environments. Five abnormal environments were defined and investigated, i.e., fire, impact, crush, immersion, and puncture. The primary interest of the study was directed toward the type of large package used to transport radioactive materials; however, the findings are not limited to this type of package but can be applied to a much larger class of material shipping containers

CH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2003-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the WIPP management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document provides the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs

CH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2002-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT Shipping Package, and directly related components. This document complies with the minimum requirements as specified in TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event there is a conflict between this document and the SARP or C of C, the SARP and/or C of C shall govern. C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SAR P charges the WIPP Management and Operation (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document details the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize these operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs

Safety during sea transport of radioactive materials. Probabilistic safety analysis of package fro sea surface fire accident

International Nuclear Information System (INIS)

Matsuoka, Takeshi; Obara, Isonori; Akutsu, Yukio; Aritomi, Masanori

2000-01-01

The ships carrying irradiated nuclear fuel, plutonium and high level radioactive wastes(INF materials) are designed to keep integrity of packaging based on the various safety and fireproof measures, even if the ship encounters a maritime fire accident. However, granted that the frequency is very low, realistic severe accidents should be evaluated. In this paper, probabilistic safety assessment method is applied to evaluate safety margin for severe sea fire accidents using event tree analysis. Based on our separate studies, the severest scenario was estimated as follows; an INF transport ship collides with oil tanker and induces a sea surface fire. Probability data such as ship's collision, oil leakage, ignition, escape from fire region, operations of cask cooling system and water flooding systems were also introduced from above mentioned studies. The results indicate that the probability of which packages cannot keep their integrity during the sea surface fire accident is very low and sea transport of INF materials is carried out very safely. (author)

Packaging design criteria for the Type B Drum

International Nuclear Information System (INIS)

Edwards, W.S.; Smith, R.J.; Wells, A.H.

1995-09-01

The Type B Drum package is a transportation cask capable of shipping a single 55-gal (208 L) drum of transuranic (TRU) waste. The Type B Drum is smaller than existing certified packages, such as the TRUPACT-II cask, but will allow payloads with higher thermal and gas generation rates, thus providing greater operational flexibility. The Type B Drum package has double containment so that plutonium contents and other radioactive material may be transported in Type B quantities. Conceptual designs of unshielded and shielded versions of the Type B Drum were completed in Report on the Conceptual Design of the Unshielded Type B Drum Packaging and Report on the Conceptual Design of the Shielded type B Drum Packaging (WEC 1994a, WEC 1994b), which demonstrated the Type B Drum to be a viable packaging system. A Type B package containment system must withstand the normal conditions of transport and the hypothetical accident conditions, which include a 9-m (30-ft) drop onto an unyielding surface and a 1-m (3-ft) drop onto a 15-cm (6-in.) diameter pin, and a fire and immersion scenarios

Roadmapping - A Tool for Resolving Science and Technology Issues Related to Processing, Packaging, and Shipping Nuclear Materials and Waste

International Nuclear Information System (INIS)

Luke, Dale Elden; Dixon, Brent Wayne; Murphy, James Anthony

2002-01-01

Roadmapping is an effective methodology to identify and link technology development and deployment efforts to a program's or project's needs and requirements. Roadmapping focuses on needed technical support to the baselines (and to alternatives to the baselines) where the probability of success is low (high uncertainty) and the consequences of failure are relatively high (high programmatic risk, higher cost, longer schedule, or higher ES and H risk). The roadmap identifies where emphasis is needed, i.e., areas where investments are large, the return on investment is high, or the timing is crucial. The development of a roadmap typically involves problem definition (current state versus the desired state) and major steps (functions) needed to reach the desired state. For Nuclear Materials (NM), the functions could include processing, packaging, storage, shipping, and/or final disposition of the material. Each function is examined to determine what technical development would be needed to make the function perform as desired. This requires a good understanding of the current state of technology and technology development and validation activities to ensure the viability of each step. In NM disposition projects, timing is crucial. Technology must be deployed within the project window to be of value. Roadmaps set the stage to keep the technology development and deployment focused on project milestones and ensure that the technologies are sufficiently mature when needed to mitigate project risk and meet project commitments. A recent roadmapping activity involved a 'cross-program' effort, which included NM programs, to address an area of significant concern to the Department of Energy (DOE) related to gas generation issues, particularly hydrogen. The roadmap that was developed defined major gas generation issues within the DOE complex and research that has been and is being conducted to address gas generation concerns. The roadmap also provided the basis for sharing

Over Batch Analysis for the LLNL Plutonium Packaging System (PuPS)

International Nuclear Information System (INIS)

Riley, D.; Dodson, K.

2007-01-01

This document addresses the concern raised in the Savannah River Site (SRS) Acceptance Criteria (Reference 1, Section 6.a.3) about receiving an item that is over batched by 1.0 kg of fissile materials. This document shows that the occurrence of this is incredible. Some of the Department of Energy Standard 3013 (DOE-STD-3013) requirements are described in Section 2.1. The SRS requirement is discussed in Section 2.2. Section 2.3 describes the way fissile materials are handled in the Lawrence Livermore National Laboratory (LLNL) Plutonium Facility (B332). Based on the material handling discussed in Section 2.3, there are only three errors that could result in a shipping container being over batched. These are: incorrect measurement of the item, selecting the wrong item to package, and packaging two items into a single shipping container. The analysis in Section 3 shows that the first two events are incredible because of the controls that exist at LLNL. The third event is physically impossible. Therefore, it is incredible for an item to be shipped to SRS that is more than 1.0 kg of fissile materials over batched

Over Batch Analysis for the LLNL DOE-STD-3013 Packaging System

International Nuclear Information System (INIS)

Riley, D.C.; Dodson, K.

2009-01-01

This document addresses the concern raised in the Savannah River Site (SRS) Acceptance Criteria about receiving an item that is over batched by 1.0 kg of fissile materials. This document shows that the occurrence of this is incredible. Some of the Department of Energy Standard 3013 (DOE-STD-3013) requirements are described in Section 2.1. The SRS requirement is discussed in Section 2.2. Section 2.3 describes the way fissile materials are handled in the Lawrence Livermore National Laboratory (LLNL) Plutonium Facility (B332). Based on the material handling discussed in Section 2.3, there are only three errors that could result in a shipping container being over batched. These are: incorrect measurement of the item, selecting the wrong item to package, and packaging two items into a single shipping container. The analysis in Section 3 shows that the first two events are incredible because of the controls that exist at LLNL. The third event is physically impossible. Therefore, it is incredible for an item to be shipped to SRS that is more than 1.0 kg of fissile materials over batched.

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant| (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations(CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2007-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

Green Shipping Practices of Shipping Firms

Directory of Open Access Journals (Sweden)

Young-Tae Chang

2017-05-01

Full Text Available The primary objective of this study is to provide an empirical research using structural equation modeling to identify the factors that motivate shipping firms to adopt green shipping practices (GSP. Furthermore, it also examines if adopting GSP can enhance the shipping firms’ environmental and productivity performance. The findings show that shipping firms are motivated to adopt GSP mostly by industrial norms set by institutionalized associations. They are also motivated by customers’ demand for environmental friendliness and their own strategy to make good image. Unlike our expectation, government regulations and international environmental laws are not significant in influencing shipping firms to adopt GSP. Moreover, adoption of green shipping practices can improve the environmental and productivity performance of the shipping firms.

Packaging and transportation of depleted uranium for disposition from the Savannah River Site

International Nuclear Information System (INIS)

Gillas, D.L.; Berg, J.

2009-01-01

The Savannah River Site (SRS) produced a large inventory of depleted uranium trioxide (DUO) in a powder form packaged in approximately 36,000 55-gallon drums that required final disposition. Each drum weighs an average of 680 kg (1,500 pounds) with some as much as 820 kg (1,800 pounds). The weight, and the fact that the material is in a powder form, requires detailed planning concerning the packaging and transportation (P and T) that must be used. Four disposition campaigns have been completed with the first in Fiscal Year 2003 (FY03), the second in FY04/05, and the most recent two campaigns being completed in early FY09. The remaining inventory of approximately 16,000 drums will likely follow similar paths in the future. This paper will describe the DUO inventory and the thought process behind determining the appropriate P and T for each campaign, very briefly covering the first two campaigns and emphasizing the most recent campaigns. In FY03, SRS completed a pilot project that disposed of 3,270 55-gallon drums of DUO. The shipping method used 110-ton mill gondola rail-cars with a polypropylene coated fabric liner as the DOT 'strong, tight' package. These rail-cars were shipped to the EnergySolutions low level waste (LLW) disposal facility in Clive, UT (previously Envirocare of Utah now referred to in this paper as the Clive Facility) for final disposition of the DUO as LLW. In FY04/05, an additional 7,296 drums that were over-packed in 85-gallon drums were shipped in boxcars (not part of the packaging) since the overpacks were qualified as IP-2 containers due to the excessive weight of the drums (over 680 kg each) to the Clive Facility. The two most recent campaigns consisted of: 1) 5,408 55-gallon drums that were shipped to the Clive Facility in 52.5-foot gondola rail-cars with fiberglass lids; the rail-car itself was the package as well as the conveyance, and 2) 4014 55-gallon drums that were shipped to the Nevada Test Site (NTS) in 20-foot modified cargo

Characterizing, for packaging and transport, large objects contaminated by radioactive material having a limited A2 value

International Nuclear Information System (INIS)

Pope, R.B.; Shappert, L.B.; Michelhaugh, R.D.; Cash, J.M.; Best, R.E.

1998-02-01

The International Atomic Energy Agency (IAEA) Regulations for the safe packaging and transportation of radioactive materials follow a graded approach to the requirements for both packaging and controls during transport. The concept is that, the lower the risk posed to the people and the environment by the contents, (1) the less demanding are the packaging requirements and (2) the smaller in number are the controls imposed on the transport of the material. There are likely to be a great number of situations arising in coming years when large objects, contaminated with radioactive material having unlimited A 2 values will result from various decommissioning and decontamination (D and D) activities and will then require shipment from the D and D site to a disposal site. Such situations may arise relatively frequently during the cleanup of operations involving mining, milling, feedstock, and uranium enrichment processing facilities. Because these objects are contaminated with materials having an unlimited A 2 value they present a low radiological risk to worker and public safety and to the environment during transport. However, when these radioactive materials reside on the surfaces of equipment and other large objects, where the equipment and objects themselves are not radioactive, the radioactive materials appear as surface contamination and, if the contaminated object is categorized as a surface contaminated object, it would need to be packaged for shipment according to the requirements of the Regulations for SCO. Despite this categorization, alternatives may be available which will allow these contaminants, when considered by themselves for packaging and transport, to be categorized as either (1) a limited quantity of radioactive material to be shipped in an excepted package or (2) low specific activity (LSA) materials to be shipped in an IP-1 package or possibly even shipped unpackaged. These options are discussed in this paper

Materials of Criticality Safety Concern in Waste Packages

International Nuclear Information System (INIS)

Larson, S.L.; Day, B.A.

2006-01-01

10 CFR 71.55 requires in part that the fissile material package remain subcritical when considering 'the most reactive credible configuration consistent with the chemical and physical form of the material'. As waste drums and packages may contain unlimited types of materials, determination of the appropriately bounding moderator and reflector materials to ensure compliance with 71.55 requires a comprehensive analysis. Such an analysis was performed to determine the materials or elements that produce the most reactive configuration with regards to both moderation and reflection of a Pu-239 system. The study was originally performed for the TRUPACT-II shipping package and thus the historical fissile mass limit for the package, 325 g Pu-239, was used [1]. Reactivity calculations were performed with the SCALE package to numerically assess the moderation or reflection merits of the materials [2]. Additional details and results are given in SAIC-1322-001 [3]. The development of payload controls utilizing process knowledge to determine the classification of special moderator and/or reflector materials and the associated fissile mass limit is also addressed. (authors)

Packaging development needs to support environmental restoration

International Nuclear Information System (INIS)

Hummer, J.H.; Kuklinski, J.L.

1993-01-01

The U.S. Department of Energy is bringing its facilities into compliance with present environmental protection regulations. At the Hanford Site, this includes cleanup of its vast nuclear and chemical wastes. Cleanup will involve extensive collecting, consolidating, and processing of radioactive and other hazardous wastes. The Hanford Site was established by the Federal government in 1943 to produce plutonium. Natural uranium was fabricated into fuel slugs, inserted into nuclear reactors, and converted into plutonium. The irradiated slugs were then sent through plutonium extraction facilities. Process waste was discharged to the ground, stored on-site, or shipped off-site for disposal. Activities grew to include nine production reactors, five coal-fired power plants, nuclear fuel fabrication, other support facilities including underground waste storage tanks, and numerous chemical and waste processing plants. Cleanup activities will require extensive transport of radioactive and other hazardous materials. Packaging developments and research are required in the following areas to enhance environmental cleanup; (1) Packaging for Large Contaminated and Activated Components. (2) Bulk Packaging for Contaminated Solids. (3) Bulk Packaging for Contaminated Liquids. (4) Environmental Samples. (J.P.N.)

Final report on special impact tests of plutonium shipping containers description of test results

International Nuclear Information System (INIS)

Bonzon, L.L.

1977-02-01

The results from tests conducted to determine the structural response of the LLD-1, Model 1518-6M, and FL-10 plutonium shipping packages when subjected to high-speed impacts (170 to 760 ft/sec) onto unyielding, concrete, and soil targets are presented

Safety evaluation for packaging for 1720-DR sodium-filled tank

International Nuclear Information System (INIS)

Mercado, M.S.

1996-01-01

Preparations are under way to sell the sodium stored in the 1720-DR tank in the 1720-DR building. This will require that the tank, as well as the 1720-DR facility, be moved to the 300 Area, so that the sodium may be melted and transferred into a railroad tanker car. Because the sodium is a hazardous material and is being shipped in a nonspecification packaging, a safety evaluation for packaging (SEP) is required. This SEP approves the sodium-filled tank for a single shipment from the 105-DR area to the 300 Area

The traveller: a new look for PWR fresh fuel packages

International Nuclear Information System (INIS)

Bayley, B.; Stilwell, W.E.; Kent, N.A.

2004-01-01

The Traveller PWR fresh fuel shipping package represents a radical departure from conventional PWR fuel package designs. This paper follows the development effort from the establishment of goals and objectives, to intermediate testing and analysis, to final testing and licensing. The discussion starts with concept origination and covers the myriad iterations that followed until arriving at a design that would meet the demanding licensing requirements, last for 30 years, and would be easy to load and unload fuel, easy to handle, inexpensive to manufacture and transport, and simple and inexpensive to maintain

Thermal Upgrading of 9977 Radioactive Material (Ram) Type B Package

International Nuclear Information System (INIS)

Gupta, N.; Abramczyk, G.

2012-01-01

The 9977 package is a radioactive material package that was originally certified to ship Heat Sources and RTG contents up to 19 watts and it is now being reviewed to significantly expand its contents in support of additional DOE missions. Thermal upgrading will be accomplished by employing stacked 3013 containers, a 3013 aluminum spacer and an external aluminum sleeve for enhanced heat transfer. The 7th Addendum to the original 9977 package Safety Basis Report describing these modifications is under review for the DOE certification. The analyses described in this paper show that this well-designed and conservatively analyzed package can be upgraded to carry contents with decay heat up to 38 watts with some simple design modifications. The Model 9977 package has been designed as a replacement for the Department of Transportation (DOT) Fissile Specification 6M package. The 9977 package is a very versatile Type B package which is certified to transport and store a wide spectrum of radioactive materials. The package was analyzed quite conservatively to increase its usefulness and store different payload configurations. Its versatility is evident from several daughter packages such as the 9978 and H1700, and several addendums where the payloads have been modified to suit the Shipper's needs without additional testing.

Conceptual design of an RTG Shipping and Receiving Facility Transportation System

International Nuclear Information System (INIS)

Black, S.J.; Gentzlinger, R.C.; Lujan, R.E.

1994-01-01

The conceptual design of an RTG Facility Transportation System which is part of the overall RTG Transportation System has been completed and is described in detail. The Facility Transportation System serves to provide locomotion, cooling, shock protection and data acquisition for the RTG package during onloading and offloading sequences. The RTG Shipping ampersand Receiving Facility Transportation System consists of a Transporter Subsystem, a Package Cooling Subsystem, and a Shock Limiting Transit Device Subsystem. The Transporter Subsystem is a custom designed welded steel cart combined with a pneumatically-driven hand tug for locomotion. The Package Cooling Subsystem provides five kilowatts of active liquid cooling via an on-board refrigeration system. The Shock Limiting Transit Device Subsystem consists of a consumable honeycomb anti-shock frame which provides shock protection for the 3855 kg (8500 LB) RTG package. These subsystems have been combined into an integrated system which will facilitate the offloading and onloading of the RTG Package into and out of the semitrailer as well as meet ALARA (as low as reasonably achievable) radiation exposure guidelines

Conceptual design of an RTG shipping and receiving facility transportation system

International Nuclear Information System (INIS)

Black, S.J.; Gentzlinger, R.C.; Lujan, R.E.

1995-01-01

The conceptual design of an RTG Facility Transportation System which is part of the overall RTG Transportation System has been completed and is described in detail. The Facility Transportation System serves to provide locomotion, cooling, shock protection and data acquisition for the RTG package during onloading and offloading sequences. The RTG Shipping ampersand Receiving Facility Transportation System consists of a Transporter Subsystem, a Package Cooling Subsystem, and a Shock Limiting Transit Device Subsystem. The Transporter Subsystem is a custom designed welded steel cart combined with a pneumatically-driven hand tug for locomotion. The Package Cooling Subsystem provides five kilowatts of active liquid cooling via an on-board refrigeration system. The Shock Limiting Transit Device Subsystem consists of a consumable honeycomb anti-shock frame which provides shock protection for the 3855 kg (8500 LB) RTG package. These subsystems have been combined into an integrated system which will facilitate the offloading and onloading of the RTG Package into and out of the semitrailer as well as meet ALARA (as low as reasonably achievable) radiation exposure guidelines. copyright 1995 American Institute of Physics

Drop Tests Results Of Revised Closure Bolt Configuration Of The Standard Waste Box, Standard Large Box 2, And Ten Drum Overpack Packagings

International Nuclear Information System (INIS)

May, C.; Opperman, E.; Mckeel, C.

2010-01-01

The Transuranic (TRU) Disposition Project at Savannah River Site will require numerous transfers of radioactive materials within the site boundaries for sorting and repackaging. The three DOT Type A shipping packagings planned for this work have numerous bolts for securing the lids to the body of the packagings. In an effort to reduce operator time to open and close the packages during onsite transfers, thus reducing personnel exposure and costs, an evaluation was performed to analyze the effects of reducing the number of bolts required to secure the lid to the packaging body. The evaluation showed the reduction to one-third of the original number of bolts had no effect on the packagings capability to sustain vibratory loads, shipping loads, internal pressure loads, and the loads resulting from a 4-ft drop. However, the loads caused by the 4-ft drop are difficult to estimate and the study recommended each of the packages be dropped to show the actual effects on the package closure. Even with reduced bolting, the packagings were still required to meet the 49 CFR 178.350 performance criteria for Type A packaging. This paper discusses the effects and results of the drop testing of the three packagings.

High-activity liquid packaging design criteria

International Nuclear Information System (INIS)

1994-05-01

In recent studies, it has been acknowledged that there is an emerging need for packaging to transport high-activity liquid off the Hanford Site to support characterization and process development activities of liquid waste stored in underground tanks. These studies have dealt with specimen testing needs primarily at the Hanford Site; however, similar needs appear to be developing at other US Department of Energy (DOE) sites. The need to ship single and multiple specimens to offsite laboratories is anticipated because it is predicted that onsite laboratories will be overwhelmed by an increasing number and size (volume) of samples. Potentially, the specimen size could range from 250 mL to greater than 50 L. Presently, no certified Type-B packagings are available for transport of high-activity liquid radioactive specimens in sizes to support Site missions

Safety analysis report for packaging (onsite) doorstop samplecarrier system

Energy Technology Data Exchange (ETDEWEB)

Obrien, J.H.

1997-02-24

The Doorstop Sample Carrier System consists of a Type B certified N-55 overpack, U.S. Department of Transportation (DOT) specification or performance-oriented 208-L (55-gal) drum (DOT 208-L drum), and Doorstop containers. The purpose of the Doorstop Sample Carrier System is to transport samples onsite for characterization. This safety analysis report for packaging (SARP) provides the analyses and evaluation necessary to demonstrate that the Doorstop Sample Carrier System meets the requirements and acceptance criteria for both Hanford Site normal transport conditions and accident condition events for a Type B package. This SARP also establishes operational, acceptance, maintenance, and quality assurance (QA) guidelines to ensure that the method of transport for the Doorstop Sample Carrier System is performed safely in accordance with WHC-CM-2-14, Hazardous Material Packaging and Shipping.

Type B drum packages

International Nuclear Information System (INIS)

McCoy, J.C.

1994-08-01

The Type B drum packages (TBD) are conceptualized as a family of containers in which a single 208 L or 114 L (55 gal or 30 gal) drum containing Type B quantities of radioactive material (RAM) can be packaged for shipment. The TBD containers are being developed to fill a void in the packaging and transportation capabilities of the U.S. Department of Energy as no container packaging single drums of Type B RAM exists offering double containment. Several multiple-drum containers currently exist, as well as a number of shielded casks, but the size and weight of these containers present many operational challenges for single-drum shipments. As an alternative, the TBD containers will offer up to three shielded versions (light, medium, and heavy) and one unshielded version, each offering single or optional double containment for a single drum. To reduce operational complexity, all versions will share similar design and operational features where possible. The primary users of the TBD containers are envisioned to be any organization desiring to ship single drums of Type B RAM, such as laboratories, waste retrieval activities, emergency response teams, etc. Currently, the TBD conceptual design is being developed with the final design and analysis to be completed in 1995 to 1996. Testing and certification of the unshielded version are planned to be completed in 1996 to 1997 with production to begin in 1997 to 1998

Calculation of shipboard fire conditions for radioactive materials packages with the methods of computational fluid dynamics

International Nuclear Information System (INIS)

Koski, J.A.; Wix, S.D.; Cole, J.K.

1997-09-01

Shipboard fires both in the same ship hold and in an adjacent hold aboard a break-bulk cargo ship are simulated with a commercial finite-volume computational fluid mechanics code. The fire models and modeling techniques are described and discussed. Temperatures and heat fluxes to a simulated materials package are calculated and compared to experimental values. The overall accuracy of the calculations is assessed

Safety analysis report for packaging (onsite) L3-181 N basin cask

International Nuclear Information System (INIS)

Adkins, H.E. Jr.

1996-01-01

Purpose of this Safety Analysis Report (SARP) is to authorize the onsite transfer of a Type B, Fissile Excepted, non-highway route controlled quantity in the L3-181 packaging from the N Basin to a storage/disposal facility within 200 West Area. This SARP provides the evaluation necessary to demonstrate that the L3-181 meets the requirements of the 'Hazardous Material Packaging and Shipping', WHC- CM-2-14, by meeting the applicable performance requirements for normal conditions of transport

Grandfathering of competent authority approved packages

International Nuclear Information System (INIS)

Osgood, N.L.

2004-01-01

International Atomic Energy Agency transportation regulations are reviewed and revised on a periodic basis as new technical and scientific information becomes available. The 1996 Edition of the Regulations for the Safe Transport of Radioactive Materials in TS-R-1 includes provisions for the use of package designs approved to previous editions of the regulations. This assures that there is no disruption of transport when the regulations are updated and revised. The revision of package design standards may make certain designs obsolete, though not necessarily unsafe. The U.S. Nuclear Regulatory Commission is the agency in the United States that certifies transportation packages for Type B and fissile materials. NRC regulations include grandfathering provisions that are comparable to and compatible with the IAEA standards. NRC staff is promoting a new system that would eliminate the need to grandfather package designs. Under the new method, any new or revised provision of the regulations that affects package standards would include its own transitional arrangements. In this way, each change would be evaluated for its safety importance. Changes in the package standards that are important to safety would be implemented immediately upon the regulations coming into force. Other changes, that do not significantly affect safety, would have longer implementation periods. In this way, all packages in use would be compatible with the regulations in force, and no specific grandfathering provisions for older designs would be needed. NRC staff has concluded that the package design standards are mature and have been shown to be protective over the past 40 years of shipping experience. We predict that future changes in package design standards will not be substantive in terms of resulting in significant changes in physical performance of a package in transport, including actual transportation accidents. The benefits of the new system would be a more predictable regulatory structure

Packaging design criteria, transfer and disposal of 102-AP mixer pump

International Nuclear Information System (INIS)

Carlstrom, R.F.

1994-01-01

A mixer pump installed in storage tank 241-AP-102 (102-AP) has failed. This pump is referred to as the 102-AP mixer pump (APMP). The APMP will be removed from 102-AP 1 and a new pump will be installed. The main purpose of the Packaging Design Criteria (PDC) is to establish criteria necessary to design and fabricate a shipping container for the transfer and storage of the APMP from 102-AP. The PDC will be used as a guide to develop a Safety Evaluation for Packaging (SEP)

Considerations relating to different types of packaging

International Nuclear Information System (INIS)

Sousselier, Y.; Cohendy, G.

1976-01-01

The transport of radioactive materials has never given rise to a serious accident in France. This is due to the high quality of the provisions contained in the Regulations and to the conscientious manner in which the latter are applied. However, it would now seem appropriate to re-examine certain of these provisions in the light of a number of minor incidents which have occurred, or merely because problems have arisen which did not exist at the time of the last revision. This applies particularly to Type B packaging, intended for irradiated fuel shipments whose considerable bulk calls for a mock-up study. The transport of Type B packaging by sea may pose the problem of its resistance to fire on normal merchant ships, and similarly its behaviour under the effect of crushing should be examined in the context of air transport. Industrial-type packaging likewise presents problems, although these are basically of a psychological nature. This is particularly the case with consignments of uraniferous concentrates, uranium hexafluoride and plutonium-contaminated wastes. The accumulation (which sometimes reaches substantial numbers) of Type A packaging on a single vehicle may involve consequences which also call for study. (author)

Safety analysis report for packaging (onsite) transuranic performance demonstration program sample packaging

International Nuclear Information System (INIS)

Mccoy, J.C.

1997-01-01

The Transuranic Performance Demonstration Program (TPDP) sample packaging is used to transport highway route controlled quantities of weapons grade (WG) plutonium samples from the Plutonium Finishing Plant (PFP) to the Waste Receiving and Processing (WRAP) facility and back. The purpose of these shipments is to test the nondestructive assay equipment in the WRAP facility as part of the Nondestructive Waste Assay PDP. The PDP is part of the U. S. Department of Energy (DOE) National TRU Program managed by the U. S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico. Details of this program are found in CAO-94-1045, Performance Demonstration Program Plan for Nondestructive Assay for the TRU Waste Characterization Program (CAO 1994); INEL-96/0129, Design of Benign Matrix Drums for the Non-Destructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996a); and INEL-96/0245, Design of Phase 1 Radioactive Working Reference Materials for the Nondestructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996b). Other program documentation is maintained by the national TRU program and each DOE site participating in the program. This safety analysis report for packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the TRU PDP sample packaging meets the onsite transportation safety requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for an onsite Transportation Hazard Indicator (THI) 2 packaging. This SARP, however, does not include evaluation of any operations within the PFP or WRAP facilities, including handling, maintenance, storage, or operating requirements, except as they apply directly to transportation between the gate of PFP and the gate of the WRAP facility. All other activities are subject to the requirements of the facility safety analysis reports (FSAR) of the PFP or WRAP facility and requirements of the PDP

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the pplication.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2009-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package (also known as the 'RH-TRU 72-B cask') and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 Code of Federal Regulations (CFR) 1.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these

Experimental measurement of a shipboard fire environment with simulated radioactive materials packages

International Nuclear Information System (INIS)

Koski, J.A.; Wix, S.D.

1996-01-01

Results from a series of eight test fires ranging in size from 2.2 to 18.8 MW conducted aboard the Coast Guard fire test ship Mayo Lykes at Mobile, Alabama are presented and discussed. Tests aboard the break-bulk type cargo ship consisted of heptane spray fires simulating engine room and galley fires, wood crib fires simulating cargo hold fires, and pool fires staged for comparison to land-based regulatory fire results. Primary instrumentation for the tests consisted of two pipe calorimeters that simulated a typical package shape for radioactive materials packages. The calorimeters were both located adjacent to the fires and on the opposite side of the cargo hold bulkhead nearest the fire. The calorimeters were constructed from 1.5 m length sections of nominal 2 foot diameter schedule 60 steel pipe. Type K thermocouples were attached at 12 locations on the circumference and ends of the calorimeter. Fire heat fluxes to the calorimeter surfaces were estimated with the use of the Sandia SODDIT inverse heat conduction code. Experimental results from all types of tests are discussed, and some comparisons are made between the environments found on the ship and those found in land-based pool fire tests

Packaged low-level waste verification system

International Nuclear Information System (INIS)

Tuite, K.T.; Winberg, M.; Flores, A.Y.; Killian, E.W.; McIsaac, C.V.

1996-01-01

Currently, states and low-level radioactive waste (LLW) disposal site operators have no method of independently verifying the radionuclide content of packaged LLW that arrive at disposal sites for disposal. At this time, disposal sites rely on LLW generator shipping manifests and accompanying records to insure that LLW received meets the waste acceptance criteria. An independent verification system would provide a method of checking generator LLW characterization methods and help ensure that LLW disposed of at disposal facilities meets requirements. The Mobile Low-Level Waste Verification System (MLLWVS) provides the equipment, software, and methods to enable the independent verification of LLW shipping records to insure that disposal site waste acceptance criteria are being met. The MLLWVS system was developed under a cost share subcontract between WMG, Inc., and Lockheed Martin Idaho Technologies through the Department of Energy's National Low-Level Waste Management Program at the Idaho National Engineering Laboratory (INEL)

Guidelines for safe design of shipping packages against brittle fracture

International Nuclear Information System (INIS)

1993-08-01

In 1992, the ninth meeting of the Standing Advisory Group on the Safe Transport of Radioactive Materials recommended the publication of this TECDOC in an effort to promote the widest debate on the criteria for the brittle fracture safe design of transport packages. The published IAEA advice on the influence of brittle fracture on material integrity is contained in Appendix IX of the Advisory Material for the IAEA Regulations for the Safety Transport of Radioactive Material (1985 Edition, as amended 1990), Safety Series No. 37. This guidance is limited in scope, dealing only with ferritic steels in general terms. It is becoming more common for designers to specify materials other than austenitic stainless steel for packaging components. The data on ferritic steels cannot be assumed to apply to other metals, hence the need for further guidance on the development of relationships describing material properties at low temperatures. The methods described in this TECDOC will be considered by the Revision Panel for inclusion in the 1996 Edition of the IAEA Regulations for the Safe Transport of Radioactive Material and the supporting documents. If accepted by the Revision Panel, this advice will be a candidate for upgrading to a Safety Practice. In the interim period, this TECDOC offers provisional advice on brittle fracture evaluation. It is acknowledged that, at this stage, the views expressed do not necessarily reflect those of the governments of Member States or organizations under whose auspices this manuscript was produced. Refs and figs

Towards Real Time Simulation of Ship-Ship Interaction

DEFF Research Database (Denmark)

Lindberg, Ole; Bingham, Harry B.; Engsig-Karup, Allan Peter

2012-01-01

We present recent and preliminary work directed towards the development of a simplified, physics-based model for improved simulation of ship-ship interaction that can be used for both analysis and real-time computing (i.e. with real-time constraints due to visualization). The goal is to implement...... accurate (realistic) and much faster ship-wave and ship-ship simulations than are currently possible. The coupling of simulation with visualization should improve the visual experience such that it can be perceived as more realistic in training. Today the state-of-art in real-time ship-ship interaction...... is for efficiency reasons and time-constraints in visualization based on model experiments in towing tanks and precomputed force tables. We anticipate that the fast, and highly parallel, algorithm described by Engsig-Karup et al. [2011] for execution on affordable modern high-throughput Graphics Processing Units...

Review of criticality safety and shielding analysis issues for transportation packages

International Nuclear Information System (INIS)

Parks, C.V.; Broadhead, B.L.

1995-01-01

The staff of the Nuclear Engineering Applications Section (NEAS) at Oak Ridge National Laboratory (ORNL) have been involved for over 25 years with the development and application of computational tools for use in analyzing the criticality safety and shielding features of transportation packages carrying radioactive material (RAM). The majority of the computational tools developed by ORNL/NEAS have been included within the SCALE modular code system (SCALE 1995). This code system has been used throughout the world for the evaluation of nuclear facility and package designs. With this development and application experience as a basis, this paper highlights a number of criticality safety and shielding analysis issues that confront the designer and reviewer of a new RAM package. Changes in the types and quantities of material that need to be shipped will keep these issues before the technical community and provide challenges to future package design and certification

The shipping man adventures in ship finance

CERN Document Server

McCleery, Matthew

2013-01-01

When restless New York City hedge fund manager Robert Fairchild watches the Baltic Dry Cargo Index plunge 97%, registering an all-time high and a 25-year low within the span of just six months, he decides to buy a ship. Immediately fantasizing about naming a vessel after his wife, carrying a string of worry beads and being able to introduce himself as a "shipowner" at his upcoming college reunion, Fairchild immediately embarks on an odyssey into the most exclusive, glamorous and high stakes business in the world. From pirates off the coast of Somalia and on Wall Street to Greek and Norwegian shipping magnates, the education of Robert Fairchild is an expensive one. In the end, he loses his hedge fund, but he gains a life - as a Shipping Man. Part fast paced financial thriller, part ship finance text book, The Shipping Man is 310 pages of required reading for anyone with an interest in capital formation for shipping.

Truck and rail charges for shipping spent fuel and nuclear waste

International Nuclear Information System (INIS)

McNair, G.W.; Cole, B.M.; Cross, R.E.; Votaw, E.F.

1986-06-01

The Pacific Northwest Laboratory developed techniques for calculating estimates of nuclear-waste shipping costs and compiled a listing of representative data that facilitate incorporation of reference shipping costs into varius logistics analyses. The formulas that were developed can be used to estimate costs that will be incurred for shipping spent fuel or nuclear waste by either legal-weight truck or general-freight rail. The basic data for this study were obtained from tariffs of a truck carrier licensed to serve the 48 contiguous states and from various rail freight tariff guides. Also, current transportation regulations as issued by the US Department of Transportation and the Nuclear Regulatory Commission were investigated. The costs that will be incurred for shipping spent fuel and/or nuclear waste, as addressed by the tariff guides, are based on a complex set of conditions involving the shipment origin, route, destination, weight, size, and volume and the frequency of shipments, existing competition, and the length of contracts. While the complexity of these conditions is an important factor in arriving at a ''correct'' cost, deregulation of the transportation industry means that costs are much more subject to negotiation and, thus, the actual fee that will be charged will not be determined until a shipping contract is actually signed. This study is designed to provide the baseline data necessary for making comparisons of the estimated costs of shipping spent fuel and/or nuclear wastes by truck and rail transportation modes. The scope of the work presented in this document is limited to the costs incurred for shipping, and does not include packaging, cask purchase/lease costs, or local fees placed on shipments of radioactive materials

MODEL 9977 B(M)F-96 SAFETY ANALYSIS REPORT FOR PACKAGING

Energy Technology Data Exchange (ETDEWEB)

Abramczyk, G; Paul Blanton, P; Kurt Eberl, K

2006-05-18

This Safety Analysis Report for Packaging (SARP) documents the analysis and testing performed on and for the 9977 Shipping Package, referred to as the General Purpose Fissile Package (GPFP). The performance evaluation presented in this SARP documents the compliance of the 9977 package with the regulatory safety requirements for Type B packages. Per 10 CFR 71.59, for the 9977 packages evaluated in this SARP, the value of ''N'' is 50, and the Transport Index based on nuclear criticality control is 1.0. The 9977 package is designed with a high degree of single containment. The 9977 complies with 10 CFR 71 (2002), Department of Energy (DOE) Order 460.1B, DOE Order 460.2, and 10 CFR 20 (2003) for As Low As Reasonably Achievable (ALARA) principles. The 9977 also satisfies the requirements of the Regulations for the Safe Transport of Radioactive Material--1996 Edition (Revised)--Requirements. IAEA Safety Standards, Safety Series No. TS-R-1 (ST-1, Rev.), International Atomic Energy Agency, Vienna, Austria (2000). The 9977 package is designed, analyzed and fabricated in accordance with Section III of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV) Code, 1992 edition.

The containment and an absorbent evaluation for a package for a liquid radioactive isotope

Energy Technology Data Exchange (ETDEWEB)

Bang, K. S.; Lee, J. C.; Kim, D. H.; Hwang, C. S.; Kim, H. J.; Seo, K. S

2005-03-01

Radioactive isotopes must be safely transported from the production centre to the point of use. The shipping package to safely transport radioactive isotopes should be able to withstand the conditions prescribed by law. A type a package, which is used to transport liquid radioactive materials, should have a containment system comprising a primary inner and a secondary outer containment or it should be provided with a sufficiently absorbent material to absorb twice the volume of the liquid contents. Accordingly, an absorbent material for use in a Type A package to transport a liquid radioactive isotope was estimated. To estimate the integrity of containment, the leakage tests for a containment system for a Type A package for domestic and abroad expert were conducted.

Safety Analysis Report for Packaging (SARP): USA/9507/BLF (ERDA--AL), Model AL-M1

International Nuclear Information System (INIS)

Watkins, R.A.; Bertram, R.E.; Blauvelt, R.K.; Edling, D.A.; Flanagan, T.M.; Griffin, J.F.; Rhinehammer, T.B.

1977-01-01

The SARP includes structural integrity, thermal resistance, radiation shielding and radiological safety, nuclear criticality safety, and quality control of three insulated drum shipping containers identified as USA/9507/BLF (ERDA-AL), also called AL-M1, configurations 1, 3, and 5. Complete physical and technical descriptions of the packages are presented. Each package consists of an inner container centered within an insulated steel drum. The contents are plutonium-239 and uranium-235 in configurations-1 and -3. The configuration-5 package is intended for shipment of up to 100,000 Ci of tritiated water immobilized on a sorbent such as molecular sieve

Are nuclear ships environmentally safer than conventionally powered ships

International Nuclear Information System (INIS)

Bone, C.A.; Molgaard, C.A.; Helmkamp, J.C.; Golbeck, A.L.

1988-01-01

An epidemiologic analysis was conducted to determine if risk of hospitalization varied by age, ship type, or occupation between nuclear and conventional powered ship crews in the U.S. Navy. Study cohorts consisted of all male enlisted personnel who served exclusively aboard conventional or nuclear powered aircraft carriers and cruisers during the years 1975-1979; cases were those men hospitalized during this period (N = 48,242). Conventional ship personnel showed significantly elevated rates of injury and disease when compared to nuclear ship personnel. The largest relative risks by age occurred for conventional ship crewmen less than 30 years old. Seaman, logistics (supply), and healthcare personnel serving aboard conventional ships comprised the occupational groups exhibiting the highest hospitalization rate differentials. The results strongly suggest that nuclear ships provide a healthier, safer working and living environment than conventional ships

Shipping

NARCIS (Netherlands)

Wijnolst, N.; Wergeland, T.

1996-01-01

Shipping is a multi-faceted industry which is rather complex to define from an academic point of view. This book attempts to grasp these complexities and provide the reader with an overview of the main topics and terminology in shipping. The book is based on material from our courses in shipping at

Using computer technology to identify the appropriate radioactive materials packaging

International Nuclear Information System (INIS)

Driscoll, K.L.; Conan, M.R.

1989-01-01

The Radioactive Materials Packaging (RAMPAC) database is designed to store and retrieve information on all non-classified packages certified for the transport of radioactive materials within the boundaries of the US. The information in RAMPAC is publicly available, and the database has been designed so that individuals without programming experience can search for and retrieve information using a menu-driven system. RAMPAC currently contains information on over 650 radioactive material shipping packages. Information is gathered from the US Department of Energy (DOE), the US Department of transportation (DOT), and the US Nuclear Regulatory Commission (NRC). RAMPAC is the only tool available to radioactive material shippers that contains and reports packaging information from all three Federal Agencies. The DOT information includes package listings from Canada, France, Germany, Great Britain, and Japan, which have DOT revalidations for their certificates of competent authority and are authorized for use within the US for import and export shipments only. RAMPAC was originally developed in 1981 by DOE as a research and development tool. In recent years, however, RAMPAC has proven to be highly useful to operational personnel. As packages become obsolete or materials to be transported change, shippers of radioactive materials must be able to determine if alternative packages exist before designing new packages. RAMPAC is designed to minimize the time required to make this determination, thus assisting the operational community in meeting their goals

International performance-oriented packaging standards adopted in the united states

International Nuclear Information System (INIS)

McCall, D.L.

1993-01-01

On January 1, 1991, the U.S. Department of Transportation (DOT) initiated a transition to adopting a modified version of current international standards for packaging and transporting hazardous materials and hazardous wastes. This transition permits a 5-year phase-in period that will impact all phases of hazardous material transportation including material classification and description, packaging for shipment, and hazard communication standards. These changes are being enacted through the DOT Federal Docket HM-181, 'Performance-Oriented Packaging Standards.' These regulatory standards will have dramatic impact on nearly 5 billion tons of hazardous materials transported within the United States each year. This paper summarizes the principal elements of the new DOT regulations, the latest implementation schedule and impacts on U.S. shipping activities, and discusses outstanding issues that remain to be solved through the next 5 years. (author)

Safety analysis report for packaging: the ORNL in-pile capsule shipping cask

International Nuclear Information System (INIS)

Evans, J.H.; Chipley, K.K.; Haynie, C.B.; Crowley, W.K.; Just, R.A.

1977-11-01

The ORNL in-pile capsule shipping cask is used to transport irradiated experimental capsules and spent fuel elements. The cask was analytically evaluated to determine its compliance with the applicable regulations governing containers in which radioactive materials are transported. Computational procedures were used to determine the structural integrity and thermal behavior of the cask relative to the general standards for normal conditions of transport and the standards for the hypothetical accident conditions. The results of the evaluation show that the cask is in compliance with the applicable regulations

Test report dot7A type A liquid packaging

Energy Technology Data Exchange (ETDEWEB)

Ketusky, E. T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brandjes, C. [Ameriphysics LLC, Knoxville, TN (United States); Benoit, T. J. [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-09-19

This section presents a general description of the DOT Specification 7A Type A liquid content packaging (HVYTAL), the liquid content evaluated as its payload, acceptable payload shipping configurations and features special to its use. This test report documents compliance with the regulatory safety requirements of 49 CFR Parts 173.24, 173.24a, 173.27, 173.410, 173.412, 173.461 – 173.466 and 178.350.

On the Global Ship Hull Bending Energy in Ship Collisions

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup; Li, Y.

2004-01-01

During ship collisions part of the kinetic energy of the involved vessels prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can be stored in elastic...... hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non trivial part of the energy released for structural deformation during the collision can be absorbed as elastic energy in global...... ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship-ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing is confined...

Documentation package for the RFID temperature monitoring system (Model 9977 packages at NTS)

International Nuclear Information System (INIS)

Chen, K.; Tsai, H.

2009-01-01

The technical basis for extending the Model 9977 shipping package periodic maintenance beyond the one-year interval to a maximum of five years is based on the performance of the O-ring seals and the environmental conditions. The DOE Packaging Certification Program (PCP) has tasked Argonne National Laboratory to develop a Radio-Frequency Identification (RFID) temperature monitoring system for use by the facility personnel at DAF/NTS. The RFID temperature monitoring system, depicted in the figure below, consists of the Mk-1 RFId tags, a reader, and a control computer mounted on a mobile platform that can operate as a stand-alone system, or it can be connected to the local IT network. As part of the Conditions of Approval of the CoC, the user must complete the prescribed training to become qualified and be certified for operation of the RFID temperature monitoring system. The training course will be administered by Argonne National Laboratory on behalf of the Headquarters Certifying Official. This is a complete documentation package for the RFID temperature monitoring system of the Model 9977 packagings at NTS. The documentation package will be used for training and certification. The table of contents are: Acceptance Testing Procedure of MK-1 RFID Tags for DOE/EM Nuclear Materials Management Applications; Acceptance Testing Result of MK-1 RFID Tags for DOE/EM Nuclear Materials Management Applications; Performance Test of the Single Bolt Seal Sensor for the Model 9977 Packaging; Calibration of Built-in Thermistors in RFID Tags for Nevada Test Site; Results of Calibration of Built-in Thermistors in RFID Tags; Results of Thermal Calibration of Second Batch of MK-I RFID Tags; Procedure for Installing and Removing MK-1 RFID Tag on Model 9977 Drum; User Guide for RFID Reader and Software for Temperature Monitoring of Model 9977 Drums at NTS; Software Quality Assurance Plan (SQAP) for the ARG-US System; Quality Category for the RFID Temperature Monitoring System; The

Packaging design criteria for the MCO cask

International Nuclear Information System (INIS)

Edwards, W.S.

1996-01-01

Approximately 2,100 metric tons of unprocessed, irradiated nuclear fuel elements are presently stored in the K Basins (including possibly 700 additional elements from PUREX, N Reactor, and 327 Laboratory). The basin water, particularly in the K East Basin, contains significant quantities of dissolved nuclear isotopes and radioactive fuel corrosion particles. To permit cleanup of the K Basins and fuel conditioning, the fuel will be transported from the 100 K Area to a Canister Storage Building (CSB) in the 200 East area. In order to initiate K Basin cleanup on schedule, the two-year fuel-shipping campaign must begin by December 1997. The purpose of this packaging design criteria is to provide criteria for the design, fabrication, and use of a packaging system to transport the large quantities of irradiated nuclear fuel elements positioned within Multiple Canister Overpacks

Application of a viscoplastic constitutive law to lead in the impact analysis of radioactive material shipping casks

International Nuclear Information System (INIS)

Wang, Zhibi; Turula, P.; Popper, G.F.

1990-01-01

Perzyna's viscoplastic material model is selected to consider the strain rate effect of lead used in radioactive material shipping packages. The model is checked using data from two scale-model tests and the deformations are found to be within 10 percent. 3 refs., 4 figs

On the global ship hull bending energy in ship collisions

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup; Li, Yujie

2009-01-01

During ship collisions part of the kinetic energy of the involved vessels immediately prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can...... be stored in elastic hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non-trivial part of the energy released for structural deformation during the collision can be absorbed as elastic...... energy in global ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship–ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing...

Packaging design criteria modified fuel spacer burial box. Revision 1

International Nuclear Information System (INIS)

Stevens, P.F.

1994-01-01

Various Hanford facilities must transfer large radioactively contaminated items to burial/storage. Presently, there are eighteen Fuel Spacer Burial Boxes (FSBBs) available on the Hanford Site for transport of such items. Previously, the FSBBS were transported from a rail car to the burial trench via a drag-off operation. To allow for the lifting of the boxes into the burial trench, it will be necessary to improve the packagings lifting attachments and provide structural reinforcement. Additional safety improvements to the packaging system will be provided by the addition of a positive closure system and package ventilation. FSBBs that are modified in such a manner are referred to as Modified Fuel Spacer Burial Boxes (MFSBs). The criteria provided by this PDC will be used to demonstrate that the transfer of the MFSB will provide an equivalent degree of safety as would be provided by a package meeting offsite transportation requirements. This fulfills the onsite transportation safety requirements implemented in WHC-CM-2-14, Hazardous Material Packaging and Shipping. A Safety Analysis Report for Packaging (SARP) will be prepared to evaluate the safety of the transfer operation. Approval of the SARP is required to authorize transfer. Criteria are also established to ensure burial requirements are met

Protecting against failure by brittle fracture in ferritic steel shipping containers

International Nuclear Information System (INIS)

Schwartz, M.W.; Langland, R.T.

1983-01-01

The possible use of ferritic steels for the containment structure of shipping casks has motivated the development of criteria for assuring the integrity of these casks under both normal and hypothetical accident conditions specified in Part 71 of the Code of Federal Regulations. The US Nuclear Regulatory Commission Regulation Guide 7.6 provides design criteria for preventing ductile failure steel shipping containers. The research described in this paper deals with criteria for preventing brittle fracture of ferritic steel shipping containers. Initially guidelines were developed for ferritic steel up to four inches thick (I). This was followed by an investigation of various criteria that might be used for monolithic thick walled casks greater than four inches thick (2). Three categories of safety are identified in the design of shipping containers. Category I, the highest level of safety, is appropriate for containment systems for spent nuclear fuel and high level waste transport packaging. In Category I, containers are designed to the highest level of safety and brittle fracture is essentially not possible. Categories II and III represent levels of safety commensurate with the consequences of release of lower levels of radioactivity. In these latter categories, consideration of factors contributing to brittle fracture, good engineering practice, and careful selection of material make brittle fracture unlikely under environmental conditions encountered during shipping. This paper will deal primarily with Category I containers. The guidelines for Category II and III containers are fully described elsewhere. 5 references, 10 figures, 3 tables

Characterization of Emissions from Open Burning of Meals Ready-to-Eat and their Paperboard Packaging

Science.gov (United States)

Emissions from burning current and candidate Meals Ready-to-Eat (MRE) packaging and shipping containers were characterized in an effort to assuage concerns that combustive disposal of waste at forward operating bases could pose an environmental or inhalation threat. Four types of...

44 years of testing radioactive materials packages at ORNL

Energy Technology Data Exchange (ETDEWEB)

Shappert, L.B.; Ludwig, S.B. [Oak Ridge National Lab., Oak Ridge, TN (United States)

2004-07-01

This paper briefly reviews the package testing at the Oak Ridge National Laboratory (ORNL) since 1960 and then examines the trends in the testing activities that occurred during the same period. Radioactive material shipments have been made from ORNL since the 1940s. The first fully operating reactor built at the ORNL site was patterned after the graphite pile constructed by Enrico Fermi under Stagg Field in Chicago. After serving as a test bed for future reactors, it became useful as a producer of radioactive isotopes. The Isotopes Division was established at ORNL to furnish radioactive materials used in the medical community. Often these shipments have been transported by aircraft worldwide due to the short half-lives of many of the materials. This paper touches briefly on the lighter and smaller radioisotope packages that were being shipped from ORNL in large numbers and then deals with the testing of packages designed to handle large radioactive sources, such as spent fuel, and other fissile materials.

44 years of testing radioactive materials packages at ORNL

International Nuclear Information System (INIS)

Shappert, L.B.; Ludwig, S.B.

2004-01-01

This paper briefly reviews the package testing at the Oak Ridge National Laboratory (ORNL) since 1960 and then examines the trends in the testing activities that occurred during the same period. Radioactive material shipments have been made from ORNL since the 1940s. The first fully operating reactor built at the ORNL site was patterned after the graphite pile constructed by Enrico Fermi under Stagg Field in Chicago. After serving as a test bed for future reactors, it became useful as a producer of radioactive isotopes. The Isotopes Division was established at ORNL to furnish radioactive materials used in the medical community. Often these shipments have been transported by aircraft worldwide due to the short half-lives of many of the materials. This paper touches briefly on the lighter and smaller radioisotope packages that were being shipped from ORNL in large numbers and then deals with the testing of packages designed to handle large radioactive sources, such as spent fuel, and other fissile materials

What should ''damaged'' mean in air transport of fissile packages

International Nuclear Information System (INIS)

Luna, R.E.; Falci, F.P.; Blackman, D.

1995-01-01

It is likely that the ongoing process to produce the 1996 version of the IAEA Regulation for the Safe Transport of Radioactive Materials, IAEA Safety Series 6(SS 6) will result in a more stringent package qualification standard for air transport of large quantities of radioactive materials (RAM) than is included in the 1990 version. During the process to define the scope of the new requirements there was extensive discussion of their impact on, and application to, fissile material package qualification criteria. Since fissile materials are shipped in a variety of packagings ranging from exempt to Type B, each packaging of each type must be evaluated for its ability to maintain subcriticality both alone and in arrays and in both damaged and undamaged condition. In the 1990 version of SS 6 ''damaged'' means the condition of a package after it had undergone the ''tests for demonstrating the ability to withstand accident conditions in transport,'' i.e., Type B qualification tests. These tests conditions are typical of severe accidents in surface modes, but are less severe than air mode qualification test environments to be applied to Type C packages. As a result, questions arose about the need for a corresponding change in the 1996 SS 6 to define ''damaged'' to include the Type C test regime for criticality evaluations of fissile packages in air transport

Status of the Beneficial Uses Shipping System cask (BUSS)

International Nuclear Information System (INIS)

Yoshimura, H.R.; Eakes, R.G.; Bronowski, D.R.

1994-01-01

The Beneficial Uses Shipping System cask is a Type B packaging developed by Sandia National Laboratories for the U.S. Department of Energy. The cask is designed to transport special form radioactive source capsules (cesium chloride and strontium fluoride) produced by the Department of Energy's Hanford Waste Encapsulation and Storage Facility. This paper describes the cask system and the analyses performed to predict the response of the cask in impact, puncture, and fire accident conditions as specified in the regulations. The cask prototype has been fabricated and Certificates of Compliance have been obtained

Tritium waste package

Science.gov (United States)

Rossmassler, Rich; Ciebiera, Lloyd; Tulipano, Francis J.; Vinson, Sylvester; Walters, R. Thomas

1995-01-01

A containment and waste package system for processing and shipping tritium xide waste received from a process gas includes an outer drum and an inner drum containing a disposable molecular sieve bed (DMSB) seated within outer drum. The DMSB includes an inlet diffuser assembly, an outlet diffuser assembly, and a hydrogen catalytic recombiner. The DMSB absorbs tritium oxide from the process gas and converts it to a solid form so that the tritium is contained during shipment to a disposal site. The DMSB is filled with type 4A molecular sieve pellets capable of adsorbing up to 1000 curies of tritium. The recombiner contains a sufficient amount of catalyst to cause any hydrogen add oxygen present in the process gas to recombine to form water vapor, which is then adsorbed onto the DMSB.

Intelligence and innovation in the packaging

International Nuclear Information System (INIS)

Kandile, N.G.

2005-01-01

Plastic polymers account for about 20 percent (by volume) of landfill space. Many cities have run out of space to dispose of their trash and are paying to ship their trash to remote locations. It is estimated that known global resources of oil will run dry in 80 years, natural gas in 70 years and coal in 700 years, but the economic impact of the depletion could hit much sooner; since prices will likely soar as resources are depleted. It is clear that researchers need to work toward replacing fossil fuel resources with renewable resources as both fuel and raw materials for many petroleum-based products . It wasn't too long ago that containers incorporating a modest percentage of recycled material represented the leading edge of environmentally responsible packaging. And while packagers continue to better the environment by using recycled content, a new category of environmentally friendly packaging materials has emerged: packaging made from renewable resources, including cornstarch, polylactic acid, and limestone. One of the newest applications of s ustainablev packaging is. The Plantic tm , a biodegradable polymer from Plantic Technologies, for a thermoformed tray . This material replaces polyvinyl chloride and PET trays and is more in line with the environmental policy. Using the Plantic technology reduce the environmental impact of packaging, without compromising the quality of the product or its presentation . Eife Cycle Assessment is a technique that could help to assess the benefits and drawbacks of Plantic tm ., According to The Society of Environmental Toxicology and Chemistry (SETAC), Eife Cycle Assessment is a n objective process to evaluate the environmental burdens associated with a product, process, or activity by identifying and quantifying energy and materials used and wastes released to the environment, and to evaluate and implement opportunities to effect environmental improvements . Eife Cycle Assessment involves three main stages: inventory

Green shipping management

CERN Document Server

Lun, Y H Venus; Wong, Christina W Y; Cheng, T C E

2016-01-01

This book presents theory-driven discussion on the link between implementing green shipping practices (GSP) and shipping firm performance. It examines the shipping industry’s challenge of supporting economic growth while enhancing environmental performance. Consisting of nine chapters, the book covers topics such as the conceptualization of green shipping practices (GSPs), measurement scales for evaluating GSP implementation, greening capability, greening and performance relativity (GPR), green management practice, green shipping network, greening capacity, and greening propensity. In view of the increasing quest for environment protection in the shipping sector, this book provides a good reference for firms to understand and evaluate their capability in carrying out green operations on their shipping activities.

Guide for reviewing safety analysis reports for packaging: Review of quality assurance requirements

International Nuclear Information System (INIS)

Moon, D.W.

1988-10-01

This review section describes quality assurance requirements applying to design, purchase, fabrication, handling, shipping, storing, cleaning, assembly, inspection, testing, operation, maintenance, repair, and modification of components of packaging which are important to safety. The design effort, operation's plans, and quality assurance requirements should be integrated to achieve a system in which the independent QA program is not overly stringent and the application of QA requirements is commensurate with safety significance. The reviewer must verify that the applicant's QA section in the SARP contains package-specific QA information required by DOE Orders and federal regulations that demonstrate compliance. 8 refs

Full scale tests on remote handled FFTF fuel assembly waste handling and packaging

International Nuclear Information System (INIS)

Allen, C.R.; Cash, R.J.; Dawson, S.A.; Strode, J.N.

1986-01-01

Handling and packaging of remote handled, high activity solid waste fuel assembly hardware components from spent FFTF reactor fuel assemblies have been evaluated using full scale components. The demonstration was performed using FFTF fuel assembly components and simulated components which were handled remotely using electromechanical manipulators, shielding walls, master slave manipulators, specially designed grapples, and remote TV viewing. The testing and evaluation included handling, packaging for current and conceptual shipping containers, and the effects of volume reduction on packing efficiency and shielding requirements. Effects of waste segregation into transuranic (TRU) and non-transuranic fractions also are discussed

The Use of Digital Radiography in the Evaluation of Radioactive Materials. Packaging Performance Testing

International Nuclear Information System (INIS)

May, C; Lawrence Gelder, L; Boyd Howard, B

2007-01-01

New designs of radioactive material shipping packages are required to be evaluated in accordance with 10 CFR Part 71, ''Packaging and Transportation of Radioactive Material''. This paper will discuss the use of digital radiography to evaluate the effects of the tests required by 10 CFR 71.71, Normal Conditions of Transport (NCT), and 10 CFR 71.73, Hypothetical Accident Conditions (HAC). One acceptable means of evaluating packaging performance is to subject packagings to the series of NCT and HAC tests. The evaluation includes a determination of the effect on the packaging by the conditions and tests. That determination has required that packagings be cut and sectioned to learn the actual effects on internal components. Digital radiography permits the examination of internal packaging components without sectioning a package. This allows a single package to be subjected to a series of tests. After each test, the package is digitally radiographed and the effects of particular tests evaluated. Radiography reduces the number of packages required for testing and also reduces labor and materials required to section and evaluate numerous packages. This paper will include a description of the digital radiography equipment used in the testing and evaluation of the 9977 and 9978 packages at SRNL. The equipment is capable of making a single radiograph of a full-sized package in one exposure. Radiographs will be compared to sectioned packages that show actual conditions compared to radiographic images

Shipping

OpenAIRE

Wijnolst, N.; Wergeland, T.

1996-01-01

Shipping is a multi-faceted industry which is rather complex to define from an academic point of view. This book attempts to grasp these complexities and provide the reader with an overview of the main topics and terminology in shipping. The book is based on material from our courses in shipping at the universities in Delft and Bergen. As with our lectures, we draw upon quite a va ried material, from research studies at a high academic level to lower level student work and purely descriptive ...

Safety evaluation for packaging (onsite) for concrete-shielded RHTRU waste drum for the 327 postirradiation testing laboratory

Energy Technology Data Exchange (ETDEWEB)

Adkins, H.E.

1996-10-29

This safety evaluation for packaging authorizes onsite transport of Type B quantities of radioactive material in the Concrete- Shielded Remote-Handled Transuranic Waste (RH TRU) Drum per WHC-CM-2-14, Hazardous Material Packaging and Shipping. The drum will be used for transport of 327 Building legacy waste from the 300 Area to the Transuranic Waste Storage and Assay Facility in the 200 West Area and on to a Solid Waste Storage Facility, also in the 200 Area.

Technology for the storage of radioactive materials packagings during maritime transport. Phase 1

International Nuclear Information System (INIS)

Ringot, C.; Chevalier, G.; Tomachevski, E.G.

1989-01-01

Following the accident of the M/S Mont Louis on August 25, 1984 carrying UF 6 cylinders, this report is a preliminary study of bibliographic data to help to define recommendations on packaging stowing for sea transport. Data on acceleration to take into account for normal or accidental transport conditions, safe areas on board that should be reserved for radioactive materials and accidents statistics are collected. Main information concerns: number of serious casualities or total losses to ships in European waters, accident causes, collision probability in function of mean distance between ships in the British Channel, selection of 8 reference accidents for future studies

Is radioactive mixed waste packaging and transportation really a problem

International Nuclear Information System (INIS)

McCall, D.L.; Calihan, T.W. III.

1992-01-01

Recently, there has been significant concern expressed in the nuclear community over the packaging and transportation of radioactive mixed waste under US Department of Transportation regulation. This concern has grown more intense over the last 5 to 10 years. Generators and regulators have realized that much of the waste shipped as ''low-level radioactive waste'' was in fact ''radioactive mixed waste'' and that these wastes pose unique transportation and disposal problems. Radioactive mixed wastes must, therefore, be correctly identified and classed for shipment. If must also be packaged, marked, labeled, and otherwise prepared to ensure safe transportation and meet applicable storage and disposal requirements, when established. This paper discusses regulations applicable to the packaging and transportation of radioactive mixed waste and identifies effective methods that waste shippers can adopt to meet the current transportation requirements. This paper will include a characterization and description of the waste, authorized packaging, and hazard communication requirements during transportation. Case studies will be sued to assist generators in understanding mixed waste shipment requirements and clarify the requirements necessary to establish a waste shipment program. Although management and disposal of radioactive mixed waste is clearly a critical issue, packaging and transportation of these waste materials is well defined in existing US Department of Transportation hazardous material regulations

Designing Adaptable Ships: Modularity and Flexibility in Future Ship Designs

Science.gov (United States)

2016-01-01

with motors, belts, shafts , seals, valves, hose spindles , and switches. If ship installation is not installed, the system will be status quo. Ship...Impact: the current centrifugal purifiers (Alfa-Laval) have experienced frequent failures with motor, belts, shafts , seals, valves, hose spindles ... Designing Adaptable Ships Modularity and Flexibility in Future Ship Designs John F. Schank, Scott Savitz, Ken Munson, Brian Perkinson, James

Safety analysis report for packaging: the ORNL HFIR spent-fuel-element shipping cask

International Nuclear Information System (INIS)

Evans, J.H.; Chipley, K.K.; Eversole, R.E.; Just, R.A.; Llewellyn, G.H.

1977-11-01

The Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) spent-fuel-element shipping cask is used to transport HFIR, Oak Ridge Research Reactor (ORR), and other reactor fuel elements. The cask was analytically evaluated to determine its compliance with the applicable regulations governing containers in which radioactive materials are transported. Computational procedures and tests were used to determine behavior of the cask relative to the general standards for the hypothetical accident conditions. The results of the evaluation show that the cask is in compliance with the applicable regulations

The licensing of shipping containers for radioactive materials

International Nuclear Information System (INIS)

Schulz-Forberg, B.

1987-01-01

In the Federal Republic of Germany the competent Federal Minister regulated the licensing procedure in a guideline while assigning the PTB the function of competent authority, and stipulating that BAM is to execute design inspection for approval. On completion of design inspection, BAM summarizes the results in a certificate which also states the measures required to be taken in quality monitoring in the manufacturing and maintenance of packagings. A sheet specifies the implemental provisions covering quality-assurance measures in planning, manufacturing, commissioning and operation of shipping items of types B(U) and B(M), and of nuclear safety classes I, II, and III. (orig./DG) [de

Aspiration requirements for the transportation of retrievably stored waste in the TRUPACT-2 package

International Nuclear Information System (INIS)

Djordjevic, S.; Drez, P.; Murthy, D.; Temus, C.

1990-01-01

The Transuranic Package Transporter-II (TRUPACT-II) is the shipping package to be used for the transportation of contact-handled transuranic (CH TRU) waste between the various US Department of Energy (DOE) sites, and to the Waste Isolation Pilot Plant (WIPP) located near Carlsbad, New Mexico. Waste (payload) containers to be transported in the TRUPACT-II package are required to be vented prior to being shipped. ''Venting'' refers to the installation of one or more carbon composite filters in the lid of the container, and the puncturing of a rigid liner (if present). This ensures that there is no buildup of pressure or potentially flammable gas concentrations in the container prior to transport. Payload containers in retrievable storage that have been stored in an unvented condition at the DOE sites, may have generated and accumulated potentially flammable concentrations of gases (primarily due to generation of hydrogen by radiolysis) during the unvented storage period. Such payload containers need to be aspirated for a sufficient period of time until safe pre-transport conditions (acceptably low hydrogen concentrations) are achieved. The period of time for which a payload container needs to be in a vented condition before qualifying for transport in a TRUPACT-II package is defined as the ''aspiration time.'' This paper presents the basis for evaluating the minimum aspiration time for a payload container that has been in unvented storage. Three different options available to the DOE sites for meeting the aspiration requirements are described in this paper. 4 refs., 2 figs

VeriTainer radiation detector for intermodal shipping containers

International Nuclear Information System (INIS)

Redus, R.H.; Alioto, M.; Sperry, D.; Pantazis, T.

2007-01-01

The VeriSpreader TM radiation detection system will monitor every container passing through a shipping terminal without impeding the flow of commerce by making the radiation measurements during normal container handling. This is accomplished by integrating neutron and spectroscopic γ-ray detectors into a container crane spreader bar, the part of the crane that directly engages the intermodal shipping containers while moving from ship to shore and vice versa. The use of a spectroscopic γ-detector reduces the rate of nuisance alarms due to naturally occurring radioactive material (NORM). The combination of γ and neutron detection reduces the effectiveness of shielding and countermeasures. The challenges in this spreader bar-based approach arise from the harsh environment, particularly the mechanical shock and the vibration of the moving spreader bar, since the measurement is taken while the container is moving. The electrical interfaces in the port environment, from the crane to a central monitoring office, present further challenges. It is the packaging, electronic interfaces, and data processing software that distinguish this system, which is based on conventional radiation sensors. The core of the system is Amptek's GAMMA-RAD, which integrates a ruggedized scintillator/PMT, digital pulse shaping electronics, electronics for the neutron detector, power supplies, and an Ethernet interface. The design of the VeriTainer system and results from both the laboratory and a proof-of-concept test at the Port of Oakland, California will be presented

Destructive Testing of an ES-3100 Shipping Container at the Savannah River National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Loftin, B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Abramczyk, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-06-09

Destructive testing of an ES-3100 Shipping Container was completed by the Packaging Technology and Pressurized Systems organization within the Savannah River National Laboratory in order to qualify the ES-3100 as a candidate storage and transport package for applications at various facilities at the Savannah River Site. The testing consisted of the detonation of three explosive charges at separate locations on a single ES-3100. The locations for the placement were chosen based the design of the ES-3100 as well as the most likely places for the package to incur damage as a result of the detonation. The testing was completed at an offsite location, which raised challenges as well as allowed for development of new partnerships for this testing and for potential future testing. The results of the testing, the methods used to complete the testing, and similar, potential future work will be discussed.

Safety Analysis Report for Packaging (SARP) for USA/5790/BLF (DOE-AL) and USA/5791/BLF (DOE-AL)

International Nuclear Information System (INIS)

Roome, L.G.; Watkins, R.A.; Bertram, R.E.; Kreider, H.B.

1980-01-01

This revised Safety Analysis Report for Packaging (SARP) includes discussions of structural integrity, thermal resistance, radiation shielding and radiological safety, nuclear criticality safety, and quality control of shipping containers. Much of the information was previously submitted to AEC/OSD/ALO and the Department of Transportation (DOT) and provided the basis for obtaining special permits DOT-SP-5790 and DOT-SP-5791 as well as the Interim Certificates of Compliance until the original SARP could be prepared and Certificates of Compliance issued by ERDA. This SARP revision incorporates information on certain design changes, the most significant of which relate to the inner container for the type 5790 package. Complete physical and technical descriptions of the packages are presented. Each package consists of a cylindrical steel inner container centered within an insulating steel drum assembly. The contents may be any radioactive materials which satisfy the requirements established in this SARP. A shipment of plutonium-238 in the form of a solid oxide is evaluated in this SARP as an example. The results of the nuclear criticality safety analysis show how much of the fissile isotopes may be shipped as Fissile Class I, II, or III for each container. Design and development considerations, the tests and evaluations required to prove the ability of the containers to withstand normal transportation conditions, and the sequence of four hypothetical accident conditions (free drop, puncture, thermal, and water immersion) are discussed. Tables, graphs, dimensional sketches, photographs, technical references, loading and shipping procedures, Mound Facility experience in using the containers, and copies of the DOE Certificates of Compliance are included. Internal reviews of the original and revised SARP's have been performed in compliance with the requirement of DOEM 5201-Part V

LCA-ship. Design tool for energy efficient ships. A Life Cycle Analysis Program for Ships. Final report

Energy Technology Data Exchange (ETDEWEB)

Jiven, Karl; Sjoebris, Anders [MariTerm AB, Goeteborg (Sweden); Nilsson, Maria [Lund Univ. (Sweden). Stiftelsen TEM; Ellis, Joanne; Traegaardh, Peter; Nordstroem, Malin [SSPA Sweden AB, Goeteborg (Sweden)

2004-05-01

In order to make it easier to include aspects during ship design that will improve environmental performance, general methods for life cycle calculations and a prototype tool for LCA calculations of ships and marine transportation have been developed. The base of the life cycle analyses is a comprehensive set of life cycle data that was collected for the materials and consumables used in ship construction and vessel operations. The computer tool developed makes it possible to quickly and simply specify (and calculate) the use of consumables over the vessel's life time cycle. Special effort has been made to allow the tool to be used for different types of vessels and sea transport. The main result from the project is the computer tool LCA ship, which incorporates collected and developed life cycle data for some of the most important materials and consumables used in ships and their operation. The computer application also contains a module for propulsion power calculations and a module for defining and optimising the energy system onboard the vessel. The tool itself is described in more detail in the Computer application manual. The input to the application should, as much as possible, be the kind of information that is normally found in a shipping company concerning vessel data and vessel movements. It all starts with defining the ship to be analysed and continues with defining how the ship is used over the lifetime. The tool contains compiled and processed background information about specific materials and processes (LCA data) connected to shipping operations. The LCA data is included in the tool in a processed form. LCA data for steel will for example include the environmental load from the steel production, the process to build the steel structure of the ship, the scrapping and the recycling phase. To be able to calculate the environmental load from the use of steel the total amount of steel used over the life cycle of the ship is also needed. The

Addendum to the Safety Analysis Report for the Steel Waste Packaging. Revision 1

International Nuclear Information System (INIS)

Crow, S.R.

1996-01-01

The Battelle Pacific Northwest National Laboratory Safety Analysis Report (SAR) for the Steel Waste Package requires additional analyses to support the shipment of remote-handled radioactive waste and special-case waste from the 324 building hot cells to PUREX for interim storage. This addendum provides the analyses required to show that this waste can be safely shipped onsite in the configuration shown

Radioisotope thermoelectric generator licensed hardware package and certification tests

International Nuclear Information System (INIS)

Goldmann, L.H.; Averette, H.S.

1994-01-01

This paper presents the Licensed Hardware package and the Certification Test portions of the Radioisotope Thermoelectric Generator Transportation System. This package has been designed to meet those portions of the Code of Federal Regulations (10 CFR 71) relating to ''Type B'' shipments of radioactive materials. The detailed information for the anticipated license is presented in the safety analysis report for packaging, which is now in process and undergoing necessary reviews. As part of the licensing process, a full-size Certification Test Article unit, which has modifications slightly different than the Licensed Hardware or production shipping units, is used for testing. Dimensional checks of the Certification Test Article were made at the manufacturing facility. Leak testing and drop testing were done at the 300 Area of the US Department of Energy's Hanford Site near Richland, Washington. The hardware includes independent double containments to prevent the environmental spread of 238 Pu, impact limiting devices to protect portions of the package from impacts, and thermal insulation to protect the seal areas from excess heat during accident conditions. The package also features electronic feed-throughs to monitor the Radioisotope Thermoelectric Generator's temperature inside the containment during the shipment cycle. This package is designed to safely dissipate the typical 4500 thermal watts produced in the largest Radioisotope Thermoelectric Generators. The package also contains provisions to ensure leak tightness when radioactive materials, such as a Radioisotope Thermoelectric Generator for the Cassini Mission, planned for 1997 by the National Aeronautics and Space Administration, are being prepared for shipment. These provisions include test ports used in conjunction with helium mass spectrometers to determine seal leakage rates of each containment during the assembly process

Classification of Ship Routing and Scheduling Problems in Liner Shipping

DEFF Research Database (Denmark)

Kjeldsen, Karina Hjortshøj

2011-01-01

This article provides a classification scheme for ship routing and scheduling problems in liner shipping in line with the current and future operational conditions of the liner shipping industry. Based on the classification, the literature is divided into groups whose main characteristics...

Application of the ASME code in designing containment vessels for packages used to transport radioactive materials

International Nuclear Information System (INIS)

Raske, D.T.; Wang, Z.

1992-01-01

The primary concern governing the design of shipping packages containing radioactive materials is public safety during transport. When these shipments are within the regulatory jurisdiction of the US Department of Energy, the recommended design criterion for the primary containment vessel is either Section III or Section VIII, Division 1, of the ASME Boiler and Pressure Vessel Code, depending on the activity of the contents. The objective of this paper is to discuss the design of a prototypic containment vessel representative of a packaging for the transport of high-level radioactive material

Safety evaluation for packaging (onsite) plutonium recycle test reactor graphite cask

Energy Technology Data Exchange (ETDEWEB)

Romano, T.

1997-09-29

This safety evaluation for packaging (SEP) provides the evaluation necessary to demonstrate that the Plutonium Recycle Test Reactor (PRTR) Graphite Cask meets the requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for transfer of Type B, fissile, non-highway route controlled quantities of radioactive material within the 300 Area of the Hanford Site. The scope of this SEP includes risk, shieldling, criticality, and.tiedown analyses to demonstrate that onsite transportation safety requirements are satisfied. This SEP also establishes operational and maintenance guidelines to ensure that transport of the PRTR Graphite Cask is performed safely in accordance with WHC-CM-2-14. This SEP is valid until October 1, 1999. After this date, an update or upgrade to this document is required.

Safety evaluation for packaging (onsite) plutonium recycle test reactor graphite cask

International Nuclear Information System (INIS)

Romano, T.

1997-01-01

This safety evaluation for packaging (SEP) provides the evaluation necessary to demonstrate that the Plutonium Recycle Test Reactor (PRTR) Graphite Cask meets the requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for transfer of Type B, fissile, non-highway route controlled quantities of radioactive material within the 300 Area of the Hanford Site. The scope of this SEP includes risk, shieldling, criticality, and.tiedown analyses to demonstrate that onsite transportation safety requirements are satisfied. This SEP also establishes operational and maintenance guidelines to ensure that transport of the PRTR Graphite Cask is performed safely in accordance with WHC-CM-2-14. This SEP is valid until October 1, 1999. After this date, an update or upgrade to this document is required

Celotex Structural Properties Tests

International Nuclear Information System (INIS)

Smith, A.C.

2001-01-01

In the course of regulatory review of the 9975 packaging, the question of the effects environmental conditions on performance of the packaging was raised. The results of previous tests of the Celotex material, used for impact absorption and thermal insulation, indicated that the effect of temperature variation was small. Accordingly, performance under ambient conditions was judged to be representative of performance under temperature extremes. To extend the database to include other effects, and in response to the questions, a series of materials tests were performed on the Celotex brand cellulose fiberboard material

Nuclear merchant ship propulsion

International Nuclear Information System (INIS)

Schroeder, E.; Jager, W.; Schafstall, H.G.

1977-01-01

The operation of about 300 nuclear naval vessels has proven the feasibility of nuclear ship propulsion. Until now six non military ships have been built or are under construction. In the Soviet Union two nuclear icebreakers are in operation, and a third one is under construction. In the western world three prototype merchant ships have been built. Of these ships only the NS OTTO HAHN is in operation and provides valuable experience for future large scale use of nuclear merchant ship propulsion. In many countries studies and plans are made for future nuclear merchant ships. Types of vessels investigated are large containerships, tankers and specialized ships like icebreakers or ice-breaking ships. The future of nuclear merchant ship propulsion depends on three interrelated items: (1) nuclear ship technology; (2) economy of nuclear ship propulsion; (3) legal questions. Nuclear merchant ship technology is based until now on standard ship technology and light water reactor technology. Except for special questions due to the non-stationary type of the plant entirely new problems do not arise. This has been proven by the recent conceptual licensing procedure for a large nuclear containership in Germany. The economics of nuclear propulsion will be under discussion until they are proven by the operation of privately owned lead ships. Unsolved legal questions e.g. in connection with port entry permissions are at present another problem for nuclear shipping. Efforts are made to solve these questions on an international basis. The future development of nuclear energy electricity production in large land based plants will stimulate the employment of smaller units. Any future development of long distance sea transport will have to take this opportunity of a reliable and economic energy supply into account

Risk Analysis on Ship Wreck and Container Cargo to Ship Navigation

Directory of Open Access Journals (Sweden)

Muhammad Badrus Zaman

2017-03-01

Full Text Available Wreck of a ship is an incident that must be avoided. Ship accidents are generally caused by a several cases, such as human error, natural disaster, technical errors, missed communication, poor condition of the ship, and many more. Ship wreckage have huge impact for ship navigation, environment, economics, and others. Those impact have many disadvantages for the shipowners, and also for environment. For examples the fuel spills that pollute the environment, make disturbance to sailing ship because the track for those navigation is blocked by the ship wreck and their cargo especially on shallow location (<50 m. These research will discuss the effect the container when it is floats on the sea and its interference other ships. The main objective of this study is to present a risk assessment on the environmental impact of the wreck and container cargo. Wrecks on the seabed is likely to pose a risk to passing ships. container and its contents as well as the possibility of refloat, and also their environmental risks emanating from the wreck and container cargo, such as fuels, lubricants, and chemical cargo. Variations scenario is a collision between ships that pass by floating containers. The frequency of refloating container, and the consequences of the passing ship depends on several factors, which will be the subject of research. However, because of the frequency of refloating containers is unlikely, then the risk is low and does not pose a danger to navigation. These risk assessment using risk matrix 5x5 which is the combined value of the frequency and consequences of the incident. The results of this study indicate the level of risk, whether the risk is accepted, not accepted or received by considering the costs and benefits (ALARP. To consequence, there are two parameters which energy is absorbed and the penetration occurs. The absorbed energy is divided into two, namely the energy absorbed by ship and the energy absorbed by containers. In this

MODELING OF OPERATION MODES OF SHIP POWER PLANT OF COMBINED PROPULSION COMPLEX WITH CONTROL SYSTEM BASED ON ELECTRONIC CONTROLLERS

Directory of Open Access Journals (Sweden)

E. A. Yushkov

2016-12-01

Full Text Available Purpose. Designing of diagrams to optimize mathematic model of the ship power plant (SPP combined propulsion complexes (CPC for decreasing operational loss and increasing fuel efficiency with simultaneous load limiting on medium revolutions diesel generator (MRDG by criterion reducing of wear and increasing operation time between repairs. Methodology. After analyzing of ship power plant modes of CPC proposed diagrams to optimize mathematic model of the above mentioned complex. The model based on using of electronic controllers in automatic regulation and control systems for diesel and thruster which allow to actualize more complicated control algorithm with viewpoint of increasing working efficiency of ship power plant at normal and emergency modes. Results. Determined suitability of comparative computer modeling in MatLab Simulink for building of imitation model objects based on it block diagrams and mathematic descriptions. Actualized diagrams to optimize mathematic model of the ship’s power plant (SPP combined propulsion complexes (CPC with Azipod system in MatLab Simulink software package Ships_CPC for decreasing operational loss and increasing fuel efficiency with simultaneous load limiting on medium revolutions diesel generator (MRDG by criterion reducing of wear and increasing operation time between repairs. The function blocks of proposed complex are the main structural units which allow to investigate it normal and emergency modes. Originality. This model represents a set of functional blocks of the components SPP CPC, built on the principle of «input-output». For example, the function boxes outputs of PID-regulators of MRDG depends from set excitation voltage and rotating frequency that in turn depends from power-station load and respond that is a ship moving or dynamically positioning, and come on input (inputs of thruster rotating frequency PID-regulator models. Practical value. The results of researches planned to use in

Buckling of Ship Structures

CERN Document Server

Shama, Mohamed

2013-01-01

Buckling of Ship Structures presents a comprehensive analysis of the buckling problem of ship structural members. A full analysis of the various types of loadings and stresses imposed on ship plating and primary and secondary structural members is given. The main causes and consequences of the buckling mode of failure of ship structure and the methods commonly used to control buckling failure are clarified. This book contains the main equations required to determine the critical buckling stresses for both ship plating and the primary and secondary stiffening structural members. The critical buckling stresses are given for ship plating subjected to the induced various types of loadings and having the most common boundary conditions encountered in ship structures.  The text bridges the gap existing in most books covering the subject of buckling of ship structures in the classical analytical format, by putting the emphasis on the practical methods required to ensure safety against buckling of ship structur...

Safety analysis report for packaging: the ORNL HFIR unirradiated fuel element shipping container

International Nuclear Information System (INIS)

Evans, J.H.; Boulet, J.A.M.; Eversole, R.E.

1977-11-01

The ORNL HFIR unirradiated fuel element shipping container was designed and fabricated at the Oak Ridge National Laboratory for the transport of HFIR unirradiated fuel elements. The container was evaluated analytically and experimentally to determine its compliance with the applicable regulations governing containers in which radioactive and fissile materials are transported, and the evaluation is the subject of this report. Computational and test procedures were used to determine the structural integrity and thermal behavior of the cask relative to the general standards for normal conditions of transport and the standards for the hypothetical accident conditions. The results of the evaluation demonstrate that the container is in compliance with the applicable regulations

A truck cask design for shipping defense high-level waste

International Nuclear Information System (INIS)

Madsen, M.M.; Zimmer, A.

1985-01-01

The Defense High-Level Waste (DHLW) cask is a Type B packaging currently under development by the U.S. Department of Energy (DOE). This truck cask has been designed to initially transport borosilicate glass waste from the Defense Waste Processing Facility (DWPF) to the Waste Isolation Pilot Plant (WIPP). Specific program activities include designing, testing, certifying, and fabricating a prototype legal-weight truck cask system. The design includes such state-of-the-art features as integral impact limiters and remote handling features. A replaceable shielding liner provides the flexibility for shipping a wide range of waste types and activity levels

Viking FellowSHIP: Norwegian hydrogen ship on the right course

International Nuclear Information System (INIS)

Larssen-Aas, Kari

2006-01-01

In the future fuel cells will change the world of shipping's economical conditions, and environmental effects from this industry. A new model of a hydrogen fuelled ship was presented at the ONS exhibition in Stavanger 2006. The technology may revolutionize the shipping industry. A brief description of the project is presented (ml)

PWR internals segmentation and packaging experience in the U.S

International Nuclear Information System (INIS)

Kreitman, P.J.

2008-01-01

Seven commercial nuclear power plants of the Pressurized Water Reactor (PWR) design have been permanently shut down in the US to date. Six of these plants have been decommissioned using dismantling methods. The remaining plant, Indian Point 1, located in Buchanan, NY, has been placed in Safe Storage. Of the six dismantled plants, five underwent extensive segmentation, separation, and packaging of their internal components to allow removal and disposal of the reactor vessel assembly. Only the Trojan Plant in Portland, Oregon, was able to ship the reactor vessel assembly with its internals intact to the final disposal site near Richland, Washington. An important part of the planning for the upcoming decommissioning of similar plants in Europe such as Chooz A in France and Zorita in Spain will be to study the lessons learned from the US efforts and apply the best practices to future projects. This paper will chronicle the evolution of the reactor internals segmentation and packaging process to date, including the planning, methodology, equipment, waste management, and packaging strategy. (author)

Safety of nuclear ships

International Nuclear Information System (INIS)

1978-01-01

Interest in the utilization of nuclear steam supply systems for merchant ships and icebreakers has recently increased considerably due to the sharp rise in oil prices and the continuing trend towards larger and faster merchant ships. Canada, for example, is considering construction of an icebreaker in the near future. On the other hand, an accident which could result in serious damage to or the sinking of a nuclear ship is potentially far more dangerous to the general public than a similar accident with a conventional ship. Therefore, it was very important to evaluate in an international forum the safety of nuclear ships in the light of our contemporary safety philosophy, taking into account the results of cumulative operating experience with nuclear ships in operation. The philosophy and safety requirement for land-based nuclear installations were outlined because of many common features for both land-based nuclear installations and nuclear ships. Nevertheless, essential specific safety requirements for nuclear ships must always be considered, and the work on safety problems for nuclear ships sponsored by the NEA was regarded as an important step towards developing an international code of practice by IMCO on the safety of nuclear merchant ships. One session was devoted to the quantitative assessment of nuclear ship safety. The probability technique of an accident risk assessment for nuclear power plants is well known and widely used. Its modification, to make it applicable to nuclear propelled merchant ships, was discussed in some papers. Mathematical models for describing various postulated accidents with nuclear ships were developed and reported by several speakers. Several papers discussed a loss-of-coolant accident (LOCA) with nuclear steam supply systems of nuclear ships and engineering design features to prevent a radioactive effluence after LOCA. Other types of postulated accidents with reactors and systems in static and dynamic conditions were also

Google Earth Visualizations of the Marine Automatic Identification System (AIS): Monitoring Ship Traffic in National Marine Sanctuaries

Science.gov (United States)

Schwehr, K.; Hatch, L.; Thompson, M.; Wiley, D.

2007-12-01

The Automatic Identification System (AIS) is a new technology that provides ship position reports with location, time, and identity information without human intervention from ships carrying the transponders to any receiver listening to the broadcasts. In collaboration with the USCG's Research and Development Center, NOAA's Stellwagen Bank National Marine Sanctuary (SBNMS) has installed 3 AIS receivers around Massachusetts Bay to monitor ship traffic transiting the sanctuary and surrounding waters. The SBNMS and the USCG also worked together propose the shifting the shipping lanes (termed the traffic separation scheme; TSS) that transit the sanctuary slightly to the north to reduce the probability of ship strikes of whales that frequent the sanctuary. Following approval by the United Nation's International Maritime Organization, AIS provided a means for NOAA to assess changes in the distribution of shipping traffic caused by formal change in the TSS effective July 1, 2007. However, there was no easy way to visualize this type of time series data. We have created a software package called noaadata-py to process the AIS ship reports and produce KML files for viewing in Google Earth. Ship tracks can be shown changing over time to allow the viewer to feel the motion of traffic through the sanctuary. The ship tracks can also be gridded to create ship traffic density reports for specified periods of time. The density is displayed as map draped on the sea surface or as vertical histogram columns. Additional visualizations such as bathymetry images, S57 nautical charts, and USCG Marine Information for Safety and Law Enforcement (MISLE) can be combined with the ship traffic visualizations to give a more complete picture of the maritime environment. AIS traffic analyses have the potential to give managers throughout NOAA's National Marine Sanctuaries an improved ability to assess the impacts of ship traffic on the marine resources they seek to protect. Viewing ship traffic

Guidelines for conducting impact tests on shipping packages for radioactive material

International Nuclear Information System (INIS)

Mok, G.C.; Carlson, R.W.; Lu, S.C.; Fischer, L.E.

1995-09-01

Federal regulation (10 CFR Part 71) specifies a number of impact conditions (free-drop, penetration, and puncture), under which a package for the transport of radioactive materials must be tested or evaluated to demonstrate compliance with the regulation. This report is a comprehensive guide to the planning and execution of these impact tests. The report identifies the required considerations for both the design, pre-, and post-test inspections of the test model and the measurement, recording, analysis, and reporting of the test data. The report also presents reasons for the requirements, identifies the major difficulties in meeting these requirements, and suggests possible methods to overcome the difficulties. Discussed in substantial detail is the use of scale models and instrumented measurements

The radioactive materials packaging handbook: Design, operations, and maintenance

International Nuclear Information System (INIS)

Shappert, L.B.; Bowman, S.M.; Arnold, E.D.

1998-01-01

As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE's cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials

The radioactive materials packaging handbook: Design, operations, and maintenance

Energy Technology Data Exchange (ETDEWEB)

Shappert, L.B.; Bowman, S.M. [Oak Ridge National Lab., TN (United States); Arnold, E.D. [Lockheed Martin Energy Systems, Oak Ridge, TN (United States)] [and others

1998-08-01

As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE`s cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials.

Energy-efficient Ship Operation – Training Requirements and Challenges

Directory of Open Access Journals (Sweden)

Michael Baldauf

2013-06-01

Full Text Available The International Maritime Organization (IMO, through its Maritime Environmental Protection Committee (MEPC, has been carrying out substantive work on the reduction and limitation of greenhouse gas emissions from international shipping since 1997, following the adoption of the Kyoto Protocol and the 1997 MARPOL Conference. While to date no mandatory GHG instrument for international shipping has been adopted, IMO has given significant consideration of the matter and has been working in accordance with an ambitious work plan with a view to adopting a package of technical provisions. Beside the efforts undertaken by IMO, it is assumed that e.g. optimized manoeuvring regimes have potential to contribute to a reduction of GHG emissions. Such procedures and supporting technologies can decrease the negative effects to the environment and also may reduce fuel consumption. However, related training has to be developed and to be integrated into existing course schemes accordingly. IMO intends to develop a Model Course aiming at promoting the energy-efficient operation of ships. This Course will contribute to the IMO’s environmental protection goals as set out in resolutions A.947(23 and A.998(25 by promulgating industry “best practices”, which reduce greenhouse gas emissions and the negative impact of global shipping on climate change. In this paper the outline of the research work will be introduced and the fundamental ideas and concepts are described. A concept for the overall structure and the development of suggested detailed content of the draft Model course will be exemplarily explained. Also, a developed draft module for the model course with samples of the suggested integrated practical exercises will be introduced and discussed. The materials and data in this publication have been obtained partly through capacity building research project of IAMU kindly supported by the International Association of Maritime Universities (IAMU and The Nippon

Dry reloading and packaging of spent fuel at TRIGA MARK I reactor of Medical University Hanover (MHH), Germany

International Nuclear Information System (INIS)

Haferkamp, D.

2008-01-01

Between 1994 and 1998 the equipment for dry reloading of a research reactor was developed by Noell, which was funded by the German Federal Government and State of Saxonia. The task of this development programme was the design and delivery of an equipment able to load the spent fuel into the shipping casks in a dry mode for research reactors, where wet loading inside the storage pool is impossible. ALARA and infrastructure conditions had to be taken into consideration. Most of the research reactors of TRIGA MARK I type or WWR-SM have operating modes for handling of spent fuel inside the pond or for transfer of spent fuel from pond to dry/wet storage pools. On the other hand, most of them cannot handle heavy weighted shipping casks inside the reactor building because of the crane capacity, or inside water pool because of dimensions and weight of shipping casks. A typical licensed normal operating procedure for spent fuel in research reactors (TRIGA MARK I) is shown. Dry unloading procedure is described. Additionally to the normal operating procedures at the MHH research reactor the following steps were necessary: - dry packaging of spent fuel elements into the loading units (six packs) in order to minimise the transfer and loading steps between the pool and shipping cask; - transfer of spent fuel loading units from dry storage pool to the shipping cask (outside the reactor building) in a shielded transfer cask; - dry reloading of loading units, into the shipping casks outside the reactor building. The Dry Reloading Equipment implies the following 5 items: 1. loading units (six packs), which includes: - capacity up to six spent fuel elements; - criticality safe placement of spent fuel elements; - handling of several spent fuel elements in an aluminium loading unit. 2. Special Transfer Cask, which includes: - shielded housing with locks; - gripper inside housing; - hoist outside housing; - computer aided operation mode for loading and unloading. 3. Transfer Vehicle

Recent situations around nuclear ships

International Nuclear Information System (INIS)

Mizuno, Hiroshi

1978-01-01

The philosophy when the safety standard for nuclear ships is drawn up and the international rules specifically for nuclear ships are summarized. As for the safety standard for nuclear ships, the safety requirements for ordinary ships, for the ships transporting nuclear reactors, for ordinary nuclear reactors, and for the reactors moving around the seas must be included. As for the international rules for nuclear ships, there are chapter 8 ''Nuclear ships'' in the International Convention on the Safety of Life at Sea, 1960 and 1974, and Safety Consideration in the Use of Ports and Approaches by Nuclear Merchant Ships. Also there are national rules and standards in Japan and foreign countries. One of the means to explore the practicality of nuclear ships is the investigation of the economy. At this time, the social merits and demerits of nuclear ships must be compared with conventional ships by taking total expenses into account without omission. When oil is depleted, the age of nuclear ships will not necessarily begin, and the will be still some competitors. The investigations concerning the economy of nuclear ships have been carried out in various countries. The present state of the development of nuclear ships in Japan and foreign countries is explained. Many conferences and symposia have been held concerning nuclear ships, and those held recently are enumerated. The realization of nuclear ship age cannot be anticipated from existing papers and shipbuilding projects. (Kako, I.)

Shipping Information Pipeline

DEFF Research Database (Denmark)

Jensen, Thomas

to creating a more efficient shipping industry, and a number of critical issues are identified. These include that shipments depend on shipping information, that shipments often are delayed due to issues with documentation, that EDI messages account for only a minor part of the needed information......This thesis applies theoretical perspectives from the Information Systems (IS) research field to propose how Information Technology (IT) can improve containerized shipping. This question is addressed by developing a set of design principles for an information infrastructure for sharing shipping...... information named the Shipping Information Pipeline (SIP). Review of the literature revealed that IS research prescribed a set of meta-design principles, including digitalization and digital collaboration by implementation of Inter-Organizational Systems based on Electronic Data Interchange (EDI) messages...

Spent Fuel Transportation Package Performance Study - Experimental Design Challenges

International Nuclear Information System (INIS)

Snyder, A. M.; Murphy, A. J.; Sprung, J. L.; Ammerman, D. J.; Lopez, C.

2003-01-01

Numerous studies of spent nuclear fuel transportation accident risks have been performed since the late seventies that considered shipping container design and performance. Based in part on these studies, NRC has concluded that the level of protection provided by spent nuclear fuel transportation package designs under accident conditions is adequate. [1] Furthermore, actual spent nuclear fuel transport experience showcase a safety record that is exceptional and unparalleled when compared to other hazardous materials transportation shipments. There has never been a known or suspected release of the radioactive contents from an NRC-certified spent nuclear fuel cask as a result of a transportation accident. In 1999 the United States Nuclear Regulatory Commission (NRC) initiated a study, the Package Performance Study, to demonstrate the performance of spent fuel and spent fuel packages during severe transportation accidents. NRC is not studying or testing its current regulations, a s the rigorous regulatory accident conditions specified in 10 CFR Part 71 are adequate to ensure safe packaging and use. As part of this study, NRC currently plans on using detailed modeling followed by experimental testing to increase public confidence in the safety of spent nuclear fuel shipments. One of the aspects of this confirmatory research study is the commitment to solicit and consider public comment during the scoping phase and experimental design planning phase of this research

Analysis of International Commodity Shipping Data and the Shipment of NORM to the United States

International Nuclear Information System (INIS)

Baciak, James E.; Ely, James H.; Schweppe, John E.; Sandness, Gerald A.; Robinson, Sean M.

2011-01-01

be shipped in 20 ft containers. Consumer products made from ceramic materials (e.g., tableware, sinks, and toilets) are generally shipped in 40 ft containers. This distinct discrepancy is due in large part to the packaging of the commodity. Consumer products are generally shipped packed in a box loaded with Styrofoam or other packing material to protect the product from breakage. Construction ceramic materials are generally shipped in less packing material, many times consisting of only a cardboard or wooden box. Granite is almost always shipped in a 20 ft container, given its very high density.

Analysis of International Commodity Shipping Data and the Shipment of NORM to the United States

Energy Technology Data Exchange (ETDEWEB)

Baciak, James E.; Ely, James H.; Schweppe, John E.; Sandness, Gerald A.; Robinson, Sean M.

2011-10-01

tiles) tend to be shipped in 20 ft containers. Consumer products made from ceramic materials (e.g., tableware, sinks, and toilets) are generally shipped in 40 ft containers. This distinct discrepancy is due in large part to the packaging of the commodity. Consumer products are generally shipped packed in a box loaded with Styrofoam or other packing material to protect the product from breakage. Construction ceramic materials are generally shipped in less packing material, many times consisting of only a cardboard or wooden box. Granite is almost always shipped in a 20 ft container, given its very high density.

SNF shipping cask shielding analysis

International Nuclear Information System (INIS)

Johnson, J.O.; Pace, J.V. III.

1996-01-01

The Waste Management and Remedial Action Division has planned a modification sequence for storage facility 7827 in the Solid Waste Storage Area (SWSA). The modification cycle is: (1) modify an empty caisson, (2) transfer the spent nuclear fuel (SNF) of an occupied caisson to a hot cell in building 3525 for inspection and possible repackaging, and (3) return the package to the modified caisson in the SWSA. Although the SNF to be moved is in the solid form, it has different levels of activity. Thus, the following 5 shipping casks will be available for the task: the Loop Transport Carrier, the In- Pile Loop LITR HB-2 Carrier, the 6.5-inch HRLEL Carrier, the HFIR Hot Scrap Carrier, and the 10-inch ORR Experiment Removal Shield Cask. This report describes the shielding tasks for the 5 casks: determination of shielding characteristics, any streaming avenues, estimation of thermal limits, and shielding calculational uncertainty for use in the transportation plan

A numerical study on ship-ship interaction in shallow and restricted waterway

Directory of Open Access Journals (Sweden)

Sungwook Lee

2015-09-01

Full Text Available In the present study, a numerical prediction method on the hydrodynamic interaction force and moment between two ships in shallow and restricted waterway is presented. Especially, the present study proposes a methodology to overcome the limitation of the two dimensional perturbation method which is related to the moored-passing ship interaction. The validation study was performed and compared with the experiment, firstly. Afterward, in order to propose a methodology in terms with the moored-passing ship interaction, further studies were performed for the moored-passing ship case with a Reynolds Averaged Navier-Stokes (RANS calculation which is using OpenFOAM with Arbitrary Coupled Mesh Interface (ACMI technique and compared with the experiment result. Finally, the present study proposes a guide to apply the two dimensional perturbation method to the moored-passing ship interaction. In addition, it presents a possibility that the RANS calculation with ACMI can applied to the ship-ship interaction without using a overset moving grid technique.

Normal conditions of transport thermal analysis and testing of a Type B drum package

International Nuclear Information System (INIS)

Jerrell, J.W.; Alstine, M.N. van; Gromada, R.J.

1995-01-01

Increasing the content limits of radioactive material packagings can save money and increase transportation safety by decreasing the total number of shipments required to transport large quantities of material. The contents of drum packages can be limited by unacceptable containment vessel pressures and temperatures due to the thermal properties of the insulation. The purpose of this work is to understand and predict the effects of insulation properties on containment system performance. The type B shipping container used in the study is a double containment fiberboard drum package. The package is primarily used to transport uranium and plutonium metals and oxides. A normal condition of transport (NCT) thermal test was performed to benchmark an NCT analysis of the package. A 21 W heater was placed in an instrumented package to simulate the maximum source decay heat. The package reached thermal equilibrium 120 hours after the heater was turned on. Testing took place indoors to minimize ambient temperature fluctuations. The thermal analysis of the package used fiberboard properties reported in the literature and resulted in temperature significantly greater than those measured during the test. Details of the NCT test will be described and transient temperatures at key thermocouple locations within the package will be presented. Analytical results using nominal fiberboard properties will be presented. Explanations of the results and the attempt to benchmark the analysis will be presented. The discovery that fiberboard has an anisotropic thermal conductivity and its effect on thermal performance will also be discussed

Nuclear ship engineering simulator

International Nuclear Information System (INIS)

Itoh, Yasuyoshi; Kusunoki, Tsuyoshi; Hashidate, Koji

1991-01-01

The nuclear ship engineering simulator, which analyzes overall system response of nuclear ship numerically, is now being developed by JAERI as an advanced design tool with the latest computer technology in software and hardware. The development of the nuclear ship engineering simulator aims at grasping characteristics of a reactor plant under the situation generated by the combination of ocean, a ship hull and a reactor. The data from various tests with the nuclear ship 'MUTSU' will be used for this simulator to modulate and verify its functions of reproducing realistic response of nuclear ship, and then the simulator will be utilized for the research and development of advanced marine reactors. (author)

A needs assessment for DOE's packaging and transportation activities - a look into the twenty-first century

International Nuclear Information System (INIS)

Pope, R.; Turi, G.; Brancato, R.; Blalock, L.; Merrill, O.

1995-01-01

The U.S. Department of Energy (DOE) has performed a department-wide scoping of its packaging and transportation needs and has arrived at a projection of these needs for well into the twenty-first century. The assessment, known as the Transportation Needs Assessment (TNA) was initiated during August 1994 and completed in December 1994. The TNA will allow DOE to better prepare for changes in its transportation requirements in the future. The TNA focused on projected, quantified shipping needs based on forecasts of inventories of materials which will ultimately require transport by the DOE for storage, treatment and/or disposal. In addition, experts provided input on the growing needs throughout DOE resulting from changes in regulations, in DOE's mission, and in the sociopolitical structure of the United States. Through the assessment, DOE's transportation needs have been identified for a time period extending from the present through the first three decades of the twenty-first century. The needs assessment was accomplished in three phases: (1) defining current packaging, shipping, resource utilization, and methods of managing packaging and transportation activities; (2) establishing the inventory of materials which DOE will need to transport on into the next century and scenarios which project when, from where, and to where these materials will need to be transported; and (3) developing requirements and projected changes for DOE to accomplish the necessary transport safely and economically

Overview of the DOE-EM Packaging Certification Program

International Nuclear Information System (INIS)

Feldman, M.R.; Bennett, M.E.; Shuler, J.M.

2009-01-01

The U.S. Department of Transportation, in 49 CFR 173.7(d) grants the U.S. Department of Energy (DOE) the power to use 'packagings made by or under the direction of the U.S. Department of Energy... for the transportation of Class 7 materials when evaluated, approved and certified by the Department of Energy against packaging standards equivalent to those specified in 10 CFR part 71'. Via DOE Order 460.1B, DOE has established the DOE Packaging Certification Program (PCP) within the Department of Environmental Management for purposes including the certification of radioactive materials packages for DOE use. This paper will provide an overview of the programs and activities currently undertaken by the PCP in support of the safe transport of radioactive materials, including technical review of Safety Analysis Reports for Packaging, development of guidance documents and training courses, a quality assurance audit and field assessment program, database and docket management, and testing and test methodology development. The paper will also highlight the various organizations currently utilized by the PCP to meet the requirements of DOE O 460.1B, as well as some creative and effective methods that are being used to meet program objectives. The DOE Package Certification Program's primary function is to perform technical reviews of SARPs in support of the packaging certification process to ensure that the maximum protection is afforded to the public, all federal regulations are met, and the process is as time-effective and cost-effective as possible. Five additional specific functions are also supported by the PCP: development of guidance documents, training courses, a QA audit and field assessment program, database and docket management, and testing methods development. Each of these functions individually contributes to the overall mission of the PCP as defined in DOE O 460.1B. Taken as a whole, these functions represent a robust program to ensure the safety of workers

Crushing Strength of Ship Structures

DEFF Research Database (Denmark)

Cerup-Simonsen, Bo; Abramowicz, W.; Høstgaard-Brene, C.N.S.

1999-01-01

The crushing response of ship structures is of primary importance to the designers and practicing engineers concerned with accidental loading and accident reconstruction of marine vehicles. Ship to-ship collisions, ship-harbor infrastructure interaction or ship-offshore structure interaction are ...

RH Packaging Program Guidance

International Nuclear Information System (INIS)

Washington TRU Solutions, LLC

2003-01-01

The purpose of this program guidance document is to provide technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the SARP and/or C of C shall govern. The C of C states: ''...each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, ''Operating Procedures,'' of the application.'' It further states: ''...each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, ''Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC approved, users need to be familiar with 10 CFR (section) 71.11, ''Deliberate Misconduct.'' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document details the instructions to be followed to operate, maintain, and test the RH-TRU 72-B packaging. This Program Guidance standardizes instructions for all users. Users shall follow these instructions. Following these instructions assures that operations are safe and meet the requirements of the SARP. This document is available on the Internet at: ttp://www.ws/library/t2omi/t2omi.htm. Users are responsible for ensuring they are using the current revision and change notices. Sites may prepare their own document using the word

Development of the nuclear ship MUTSU spent fuel shipping cask

International Nuclear Information System (INIS)

Ishizuka, M.; Umeda, M.; Nawata, Y.; Sato, H.; Honami, M.; Nomura, T.; Ohashi, M.; Higashino, A.

1989-01-01

After the planned trial voyage (4700 MWD/MTU) of the nuclear ship MUTSU in 1990, her spent fuel assemblies, initially made of two types of enriched UO 2 (3.2wt% and 4.4wt%), will be transferred to the reprocessing plant soon after cooling down in the ship reactor for more than one year. For transportation, the MUTSU spent fuel shipping casks will be used. Prior to transportation to the reprocessing plant, the cooled spent fuel assemblies will be removed from the reactor to the shipping casks and housed at the spent fuel storage facility on site. In designing the MUTSU spent fuel shipping cask, considerations were given to make the leak-tightness and integrity of the cask confirmable during storage. The development of the cask and the storage function demonstration test were performed by Japan Atomic Energy Research Institute (JAERI) and Mitsubishi Heavy Industries, Ltd. (MHI). One prototype cask for the storage demonstration test and licensed thirty-five casks were manufactured between 1987 and 1988

TEST and EVALUATION REPORT FOR THE HEDGEHOG-II PACKAGING SYSTEMS DOT-7A TYPE A CONTAINER

International Nuclear Information System (INIS)

KELLY, D.L.

2003-01-01

This report documents the US. Department of Transportation Specification 7A (DOT-7A) Type A compliance test and evaluation results for the Hedgehog-II packaging systems. The approved Hedgehog-II packaging configurations provide primary and secondary containment. The approved packaging configurations described within this report are designed to ship Type A quantities of radioactive materials, normal form. Contents may be in solid or liquid form. Liquids transported in the approved 1 L glass bottle assembly shall have a specific gravity of less than or equal to 1.6. Liquids transported in all other approved configurations shall have a specific gravity of less than or equal to 2.0. The solid contents, including packaging, are limited in weight to the gross weight of the as-tested liquids and bottles. The approved Hedgehog-II packaging configurations described in this report may be transported by air, and have been evaluated as meeting the applicable International Air Transport Association/International Civil Aviation Organization (IATA/ICAO) Dangerous Goods Regulations in addition to the DOT requirements

Ship Vibrations

DEFF Research Database (Denmark)

Sørensen, Herman

1997-01-01

Methods for calculating natural frequencies for ship hulls and for plates and panels.Evaluation of the risk for inconvenient vibrations on board......Methods for calculating natural frequencies for ship hulls and for plates and panels.Evaluation of the risk for inconvenient vibrations on board...

Design of strong wooden box coated with fiberglass reinforced resin for shipping and burial of contaminated glove boxes. Final report

International Nuclear Information System (INIS)

1982-01-01

The project scope of work included the complete decontamination and decommissioning (D and D) of the Westinghouse ARD Fuel Laboratories at the Cheswick Site in the shortest possible time. This has been accomplished in the following four phases: (1) preparation of documents and necessary paperwork; packaging and shipping of all special nuclear materials in an acceptable form to a reprocessing agency; (2) decontamination of all facilities, glove boxes and equipment; loading of generated waste into bins, barrels and strong wooden boxes; (3) shipping of al bins, barrels and boxes containing waste to the designated burial site; removal of all utility services from the laboratories; and (4) final survey of remaining facilities and certification for nonrestricted use; preparation of final report. This attachment contains design of strong wooden box coated with fiberglass reinforced resin for shipping and burial of contaminated glove boxes

Recycling of merchant ships

Directory of Open Access Journals (Sweden)

Magdalena Klopott

2013-12-01

Full Text Available The article briefly outlines the issues concerning ship recycling. It highlights ships' high value as sources of steel scrap and non-ferrous metals, without omitting the fact that they also contain a range of hazardous substances. Moreover, the article also focuses on basic ship demolition methods and their environmental impact, as well as emphasizes the importance of “design for ship recycling” philosophy.

Consignor's part and multimodality of the packages of RAM

International Nuclear Information System (INIS)

Grenier, M.

1993-01-01

One of the essential principles of Safety in transport of RAM as it was carried on, until the present days, is that the safety comes firstly from the packaging, and not from a special consideration of the mode of transport or anything else. A natural consequence was that the packaging remains the same, whatever is the used mode of transport, another that the transport mode does not take part, otherly than by its normal safety in the carriage itself in the protection against the radioactive hazard. Some recent actions, nevertheless, could be considered as putting some doubt on the implementation of this principles in the regulations and sometimes on these principles themselves. However, these latter come from the fact that the safety of the transport lays essentially in the hands of the consignor. He is indeed the only one who knows well enough the material and who is able to assess the adequation of the packaging and to warrant it to the Competent Authority when necessary. Besides, the packaging is the only direct grasp he has on the shipment, outside the special case of exclusive use. This situation is not completely incompatible with a new possible graduation of the packaging according to the transport mode, under the condition that this graduation be unidimensional which means the same in every field of testing. The consignor must, then, select the packaging corresponding to the most demanding of the possible modes. It is certainly much more difficult to adapt the mode of transport to the shipped materials themselves. All the transport has then to be in the hands of the consignor. That perhaps, can be relevant to industrial nuclear transport (eg: irradiated fuels, wastes), but not to the carriage of radioactive materials in general, which is the scope of IAEA regulations. (author)

Licensing experiences, risk assessment, demonstration test on nuclear fuel packages and design criteria for sea going vessel carrying spent fuel in Japan

International Nuclear Information System (INIS)

Aoki, S.; Ikeda, K.

1978-01-01

In Japan spent fuels from nuclear power plants shall be shipped to reprocessing plants by sea-going vessels. Atomic Energy Committee has initiated a board of experts to implement the assessment of environmental safety for sea transport. As a part of the assessment a study has been conducted by Central Research Institute of Electric Power Industry under sponsorship of Nuclear Safety Bureau, which is intended to guarantee the safety of sea transport. Nuclear Safety Bureau also has a program to carry out a long term demonstration test on spent fuel package using full scale package models. The test consists of drop, heat transfer, fire, collapse under high external pressure, immersion, shielding and subcritical test. The purpose of this test is to obtain the public acceptance and also to verify the adequacy of the safety analysis for nuclear fuel packages. In order to secure the safety of sea transport, the Ministry of Transportation has provided for the design criteria for sea-going vessel in the case of full load shipping, which aims to make minimum the probability of sinking at collision, grounding and other unforeseen accidents on the sea and also to retain the radiation exposure to crews as low as possible. The design criteria consists of the following items: (1) structural strength of vessel, (2) collision protective structure, (3) arrangement of holds, (4) stability after damage, (5) grounding protective structure, (6) cooling system, (7) tie-down equipment, (8) radiation inspection apparatus, (9) decontamination facilities, (10) emergency water flooding equipment for ship fire, (11) emergency electric sources, etc. Based on the design criteria a sea-going vessel names HINOURA-MARU has been reconstructed to transport spent fuel packages from nuclear power stations to the reprocessing plant

Development of waste package designs for disposal in a salt repository

International Nuclear Information System (INIS)

Balmert, M.E.

1983-01-01

Three package design concepts were developed for CHLW and DHLW forms and spent fuel rods: (1) carbon steel overpack, borehole emplacement, (2) titanium clad, carbon steel reinforced overpack, borehole emplacement, and (3) carbon steel (self-shield) overpack, tunnel emplacement. For a DHLW canister with titanium clad overpack, the concept features a 9.5-cm-thick carbon steel overpack reinforcement supporting a 0.25-cm-thick titanium shell. The overall package dimensions are 84 cm diameter x 340 cm long weighing about 8.8 mtons. By contrast, a monolithic DHLW borehole package has a carbon steel overpack that is 10.4 cm thick, weighing about 9.3 mtons. The titanium clad/carbon steel reinforced borehole package is intended for remote emplacement in a vertical borehole in salt. The carbon steel overpack reinforcement provides structural integrity, primarily to resist external pressure, while the titanium overpack provides the necessary corrosion resistance to meet containment requirements. The carbon steel borehole package concept provides containment integrity for both external pressure and corrosion environments with a thicker carbon steel overpack in place of the titanium/carbon steel concept. A third concept utilizes an even greater thickness of cast steel or iron to resist external pressure and corrosion as well as reduce external shielding requirements. For example, a cast steel DHLW package would have overall dimensions of 125 cm diameter x 390 cm long, weighing 31 mtons. The purpose of this self-shield concept is to minimize handling and emplacement operations by reducing the package surface radiation dose to about 100 mrem/hr. In addition, it may serve as a shipping cask, thereby eliminating the need for a shielded hot cell at the repository for waste package assembly operations. 7 figures

System certification: An alternative to package certification?

International Nuclear Information System (INIS)

Luna, R.E.; Jefferson, R.J.

1991-01-01

One precept of the current radioactive material transportation regulations is that the package is the primary protection for the public. A packaging is chosen to provide containment, shielding, and criticality control suitable to the quantity and characteristics of the radionuclide being transported. Occasionally, radioactive materials requiring transport are not of a mass or size that would allow the materials to be shipped in an appropriate packaging. Where the shipment to be made is relatively infrequent, there may be economic and time penalties that may hamper shipment or force the shipper into uneconomic or high risk options. However, there is recognition of such situations in the International Atomic Energy Agency (IAEA) regulations under the provisions for Special Arrangement. The principal paragraphs defining Special Arrangement in Regulations for the Safe of Radioactive Material; Safety Series 6 (SS6) [IAEA, 1990a] are 141, 211, 720, and 727. In the US regulations the applicable term is ''Exemption.'' An exemption is obtained from either the United States Department of Transportation (USDOT) or the United States Nuclear Regulatory Commission (USNRC) depending on the character of the needed exemption. The essential concept is that some requirements of the regulations that apply in a given situation are not required if the shipment is subjected to other operational controls that provide an equivalent level of risk to that attained if the regulations were observed fully. This paper deals primarily with changing of packaging requirements in Special Arrangements, but it is also true that operational requirements also may be changed as a result of an Exemption or Special Arrangement approval by a regulatory authority

Nuclear ships and their safety

Energy Technology Data Exchange (ETDEWEB)

NONE

1961-04-15

Several aspects of nuclear ship propulsion, with special reference to nuclear safety, were discussed at an international symposium at Taormina, Italy, from 14-18 November 1960. Discussions on specific topics are conducted, grouped under the following headings: Economics and National Activities in Nuclear Ship Propulsion; International Problems and General Aspects of Safety for Nuclear Ships; Nuclear Ship Projects from the Angle of Safety; Ship Reactor Problems; Sea Motion and Hull Problems; Maintenance and Refuelling Problems; and Safety Aspects of Nuclear Ship Operation.

Test and evaluation report for Lockheed Idaho Technologies Company, arrow-pak packaging, docket 95-40-7A, type A container

International Nuclear Information System (INIS)

Kelly, D.L.

1996-01-01

This report incorporates the U.S. Department of Energy, Office of Facility Safety Analysis (DOE/EH-32) approval letter for packaging use. This report documents the U.S. Department of Transportation Specification 7A Type A (DOT-7A) compliance test results of the Arrow-Pak packaging. The Arrow-Pak packaging system consists of Marlex M-8000 Driscopipe, manufactured by Phillips-Driscopipe, Inc., and is sealed with two dome-shaped end caps manufactured from the same materials. The patented sealing process involves the use of electrical energy to heat opposing faces of the pipe and end caps, and hydraulic rams to press the heated surfaces together. This fusion process produces a homogeneous bonding of the end cap to the pipe. The packaging may be used with or without the two internal plywood spacers. This packaging configuration described in this report is designed to ship Type A quantities of solid radioactive materials

Approximate Method of Calculating Forces on Rudder During Ship Sailing on a Shipping Route

Directory of Open Access Journals (Sweden)

K. Zelazny

2014-09-01

Full Text Available Service speed of a ship in real weather conditions is a basic design parameter. Forecasting of this speed at preliminary design stage is made difficult by the lack of simple but at the same accurate models of forces acting upon a ship sailing on a preset shipping route. The article presents a model for calculating forces and moment on plane rudder, useful for forecasting of ship service speed at preliminary stages of ship design.

Nuclear ship accidents

International Nuclear Information System (INIS)

Oelgaard, P.L.

1993-05-01

In this report available information on 28 nuclear ship accident and incidents is considered. Of these 5 deals with U.S. ships and 23 with USSR ships. The ships are in almost all cases nuclear submarines. Only events that involve the nuclear propulsion plants, radiation exposures, fires/explosions and sea water leaks into the submarines are considered. Comments are made on each of the events, and at the end of the report an attempt is made to point out the weaknesses of the submarine designs which have resulted in the accidents. It is emphasized that much of the available information is of a rather dubious nature. consequently some of the assessments made may not be correct. (au)

TEMPERATURE PREDICTION IN 3013 CONTAINERS IN K AREA MATERIAL STORAGE (KAMS) FACILITY USING REGRESSION METHODS

International Nuclear Information System (INIS)

Gupta, N

2008-01-01

3013 containers are designed in accordance with the DOE-STD-3013-2004. These containers are qualified to store plutonium (Pu) bearing materials such as PuO2 for 50 years. DOT shipping packages such as the 9975 are used to store the 3013 containers in the K-Area Material Storage (KAMS) facility at Savannah River Site (SRS). DOE-STD-3013-2004 requires that a comprehensive surveillance program be set up to ensure that the 3013 container design parameters are not violated during the long term storage. To ensure structural integrity of the 3013 containers, thermal analyses using finite element models were performed to predict the contents and component temperatures for different but well defined parameters such as storage ambient temperature, PuO 2 density, fill heights, weights, and thermal loading. Interpolation is normally used to calculate temperatures if the actual parameter values are different from the analyzed values. A statistical analysis technique using regression methods is proposed to develop simple polynomial relations to predict temperatures for the actual parameter values found in the containers. The analysis shows that regression analysis is a powerful tool to develop simple relations to assess component temperatures

Final evaluation report for Lockheed Idaho Technologies Company, ARROW-PAK packaging, Docket 95-40-7A, Type A container

International Nuclear Information System (INIS)

Kelly, D.L.

1995-11-01

The report documents the U.S. Department of Transportation Specification 7A Type A (DOT-7A) compliance test results of the ARROW-PAK packaging. The ARROW-PAK packaging system consists of Marlex M-8000 Driscopipe (Series 8000 [gas] or Series 8600 [industrial]) resin pipe, manufactured by Phillips-Driscopipe, Inc., and is sealed with two dome-shaped end caps manufactured from the same materials. The patented sealing process involves the use of electrical energy to heat opposing faces of the pipe and end caps, and hydraulic rams to press the heated surfaces together. This fusion process produces a homogeneous bonding of the end cap to the pipe. The packaging may be used with or without the two internal plywood spacers. This packaging was evaluated and tested in October 1995. The packaging configuration described in this report is designed to ship Type A quantities of solid radioactive materials, Form No. 1, Form No. 2, and Form No. 3

Development of the Nuclear Ship Database. 1. Outline of the Nuclear Ship Experimental Database

Energy Technology Data Exchange (ETDEWEB)

Kyouya, Masahiko; Ochiai, Masa-aki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Hashidate, Kouji

1995-03-01

We obtained the experimental data on the effects of the ship motions and the change in load and caused by the ship operations, the waves, the winds etc., to the nuclear power plant behavior, through the Power-up Tests and Experimental Voyages of the Nuclear Ship MUTSU. Moreover, we accumulated the techniques, the knowledge and others on the Nuclear Ship development at the each stage of the N.S. MUTSU Research and Development program, such as the design stage, the construction stage, the operation stage and others. These data, techniques, knowledge and others are the assembly of the experimental data and the experiences through the design, the construction and the operation of the first nuclear ship in JAPAN. It is important to keep and pigeonhole these products of the N.S. MUTSU program in order to utilize them effectively in the research and development of the advanced marine reactor, since there is no construction plan of the nuclear ship for the present in JAPAN. We have been carrying out the development of the Nuclear Ship Database System since 1991 for the purpose of effective utilization of the N.S. MUTSU products in the design study of the advanced marine reactors. The part of the Nuclear Ship Database System on the experimental data, called Nuclear Ship Experimental Database, was already accomplished and utilized since 1993. This report describes the outline and the use of the Nuclear Ship Experimental Database.The remaining part of the database system on the documentary data, called Nuclear Ship Documentary Database, are now under development. (author).

Development of the Nuclear Ship Database. 1. Outline of the Nuclear Ship Experimental Database

International Nuclear Information System (INIS)

Kyouya, Masahiko; Ochiai, Masa-aki; Hashidate, Kouji.

1995-03-01

We obtained the experimental data on the effects of the ship motions and the change in load and caused by the ship operations, the waves, the winds etc., to the nuclear power plant behavior, through the Power-up Tests and Experimental Voyages of the Nuclear Ship MUTSU. Moreover, we accumulated the techniques, the knowledge and others on the Nuclear Ship development at the each stage of the N.S. MUTSU Research and Development program, such as the design stage, the construction stage, the operation stage and others. These data, techniques, knowledge and others are the assembly of the experimental data and the experiences through the design, the construction and the operation of the first nuclear ship in JAPAN. It is important to keep and pigeonhole these products of the N.S. MUTSU program in order to utilize them effectively in the research and development of the advanced marine reactor, since there is no construction plan of the nuclear ship for the present in JAPAN. We have been carrying out the development of the Nuclear Ship Database System since 1991 for the purpose of effective utilization of the N.S. MUTSU products in the design study of the advanced marine reactors. The part of the Nuclear Ship Database System on the experimental data, called Nuclear Ship Experimental Database, was already accomplished and utilized since 1993. This report describes the outline and the use of the Nuclear Ship Experimental Database.The remaining part of the database system on the documentary data, called Nuclear Ship Documentary Database, are now under development. (author)

Dutch Ships and Sailors

NARCIS (Netherlands)

de Boer, Victor; Hoekstra, F.G.; Leinenga, Jurjen; van Rossum, Matthias

2014-01-01

Dutch Ships and Sailors provides an infrastructure for maritime historical datasets, linking correlating data through semantic web technology. It brings together datasets related to recruitment and shipping in the East-India trade (mainly 18th century) and in the shipping of the northern provinces

Reactors. Nuclear propulsion ships

International Nuclear Information System (INIS)

Fribourg, Ch.

2001-01-01

This article has for object the development of nuclear-powered ships and the conception of the nuclear-powered ship. The technology of the naval propulsion P.W.R. type reactor is described in the article B.N.3 141 'Nuclear Boilers ships'. (N.C.)

A radioactive waste transportation package monitoring system for normal transport and accident emergency response conditions

International Nuclear Information System (INIS)

Brown, G.S.; Cashwell, J.W.; Apple, M.L.

1991-01-01

Shipments of radioactive material (RAM) constitute but a small fraction of the total hazardous materials shipped in the United States each year. Public perception, however, of the potential consequences of a release from a transportation package containing RAM has resulted in significant regulation of transport operations, both to ensure the integrity of a package in accident conditions and to place operational constraints on the shipper. Much of this attention has focused on shipments of spent nuclear fuel and high level wastes which, although comprising a very small number of total shipments, constitute a majority of the total curies transported on an annual basis. This report discusses the shipment of these highly radioactive materials

Ship Acquisition of Shipping Companies by Sale & Purchase Activities for Sustainable Growth: Exploratory Fuzzy-AHP Application

Directory of Open Access Journals (Sweden)

Keun-Sik Park

2018-05-01

Full Text Available Strengthening sale and purchase (S&P capacity has become a fundamental requirement for sustainable growth and corporate competitiveness in the modern shipping market. However, there is a lack of research related to S&P and its priority when shipping companies attempt to implement ship acquisition through S&P activities. To fill this gap, this paper conducts an empirical analysis to analyze priority factors during the acquisition of second-hand ships from the perspective of shipping companies. Business criteria are considered to be the most important factors in the analysis of the priority of ship acquisition and investment in shipping companies. To the best of our knowledge, this research is the first exploration covering Korean shipping companies’ ship acquisition through S&P activities. This study is expected to contribute to the better understanding of the role of S&P in ensuring the sustainability of shipping companies and to provide stakeholders with valuable insights.

Safety evaluation for packaging 222-S laboratory cargo tank for onetime type B material shipment

International Nuclear Information System (INIS)

Nguyen, P.M.

1994-01-01

The purpose of this Safety Evaluation for Packaging (SEP) is to evaluate and document the safety of the onetime shipment of bulk radioactive liquids in the 222-S Laboratory cargo tank (222-S cargo tank). The 222-S cargo tank is a US Department of Transportation (DOT) MC-312 specification (DOT 1989) cargo tank, vehicle registration number HO-64-04275, approved for low specific activity (LSA) shipments in accordance with the DOT Title 49, Code of Federal Regulations (CFR). In accordance with the US Department of Energy, Richland Operations Office (RL) Order 5480.1A, Chapter III (RL 1988), an equivalent degree of safety shall be provided for onsite shipments as would be afforded by the DOT shipping regulations for a radioactive material package. This document demonstrates that this packaging system meets the onsite transportation safety criteria for a onetime shipment of Type B contents

L01818: NOS Hydrographic Survey

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The National Oceanic and Atmospheric Administration (NOAA) has the statutory mandate to collect hydrographic data in support of nautical chart compilation for safe...

Disease: H01818 [KEGG MEDICUS

Lifescience Database Archive (English)

Full Text Available t, but a trend toward less severe epilepsy and cognitive impairment is usually observed after the age of 5 y...a K, Maekawa K ... TITLE ... Management of and prophylaxis against status epilepticus in children with severe myoclonic epilepsy

Safety Analysis Report: Packages, Pu oxide and Am oxide shipping cask: Packaging of fissile and other radioactive materials: Final report

International Nuclear Information System (INIS)

Chalfant, G.G.

1984-12-01

The PuO 2 cask or 5320-3 cask is designed for shipment of americium or plutonium by surface transportation modes. The cask design was physically tested to demonstrate that it met the criteria specified in US ERDA Manual Chapter 0529, dated 12/21/76, which invokes Title 10 Code of Federal Regulations, Part 71 (10 CFR 71) ''Packaging of Radioactive Materials for Transport,'' and Title 49 CFR Parts 171.179 ''Hazardous Materials Regulations.'' (US DOE Order 4580.1A, Chapter III, superseded manual chapter 0529 effective May 1981, but it retained the same 10 CFR 71 and 49 CFR 171-179 references

Shipping emission forecasts and cost-benefit analysis of China ports and key regions' control.

Science.gov (United States)

Liu, Huan; Meng, Zhi-Hang; Shang, Yi; Lv, Zhao-Feng; Jin, Xin-Xin; Fu, Ming-Liang; He, Ke-Bin

2018-05-01

China established Domestic Emission Control Area (DECA) for sulphur since 2015 to constrain the increasing shipping emissions. However, future DECA policy-makings are not supported due to a lack of quantitive evaluations. To investigate the effects of current and possible Chinese DECAs policies, a model is presented for the forecast of shipping emissions and evaluation of potential costs and benefits of an DECA policy package set in 2020. It includes a port-level and regional-level projection accounting for shipping trade volume growth, share of ship types, and fuel consumption. The results show that without control measures, both SO 2 and particulate matter (PM) emissions are expected to increase by 15.3-61.2% in Jing-Jin-Ji, the Yangtze River Delta, and the Pearl River Delta from 2013 to 2020. However, most emissions can be reduced annually by the establishment of a DECA that depends on the size of the control area and the fuel sulphur content limit. Costs range from 0.667 to 1.561 billion dollars (control regional shipping emissions) based on current fuel price. A social cost method shows the regional control scenarios benefit-cost ratios vary from 4.3 to 5.1 with large uncertainty. Chemical transportation model combined with health model method is used to get the monetary health benefits and then compared with the results from social cost method. This study suggests that Chinese DECAs will reduce the projected emissions at a favorable benefit-cost ratio, and furthermore proposes policy combinations that provide high cost-effective benefits as a reference for future policy-making. Crown Copyright © 2018. Published by Elsevier Ltd. All rights reserved.

Outer Dynamics of Ship Collisions

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup

1996-01-01

The purpose is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisions with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding structures....

Directory of national competent authorities' approval certificates for package design, special form material and shipment of radioactive material. 2000 edition

International Nuclear Information System (INIS)

2000-08-01

Safety in the transport of radioactive material is dependent on packaging appropriate for the contents being shipped, rather than on operational and/or administrative actions required on the package. The grater the radiological risk posed by the material being moved, the more stringent become the performance for the packaging that can be authorised to contain it. These principles have been expanded since 1061 into a set of regulations that are responsible for safety moving the ever-growing number and complexity of radioactive material shipments throughout the world. The IAEA Regulations for the Safe Transport of Radioactive Material are incorporated into UN regulations, as well as the requirements of other international transport organizations. This is the eleventh report published by the IAEA since implementing its database on package approval certificates (PACKTRAM) at the recommendation of the Transport safety Standards Advisory Committee (TRANSSAC). Through the PACKTRAM database, the IAEA collects administrative and technical information provided by the issuing competent authority about package approval certificates

Handbook of nuclear ships

International Nuclear Information System (INIS)

1981-03-01

First, the government organs and other organizations related to nuclear ships and their tasks are described. The fundamental plan for the development of nuclear ships had been determined in July, 1963, and was revised three times thereafter. However in December, 1980, new determination to carry out the research works also was made. The course of the construction of the nuclear ship ''Mutsu'' from 1955 to 1980, the main particulars of the nuclear ship ''Mutsu'' and the drawing of the general arrangement are shown. The designated port for berthing the Mutsu was completed in 1972 in Ominato, Aomori Prefecture, but after the happening of radiation leak during the trial operation of the Mutsu in 1974, it was agreed to remove the port. The main works to be carried out at the port and the port facilities are explained. The progress of the examination of safety of the Mutsu and the result, the test of raising the power output carried out in 1974, and the course of selecting the port for making the repair works of the Mutsu are described. The law concerning Japan Nuclear Ship Research and Development Agency had been instituted in 1963, and was revised four times thereafter. The change of the budget for the tests and researches related to nuclear ships in Japan is shown. The state of development of nuclear ships in foreign countries, the international organs related to atomic energy, shipping, shipbuilding and energy, and chronological table are introduced. (Kako, I.)

Outer Dynamics of Ship Collisions

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup

1996-01-01

The purpose of these notes is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisons with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding...

On Impact Mechanics in Ship Collisions

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup; Zhang, Shengming

1998-01-01

The purpose of this paper is to present analytical, closed-form expressions for the energy released for crushing and the impact impulse during ship collisions. Ship-ship collisions, ship collisions with rigid walls and ship collisions with flexible offshore structures are considered. The derived ...

Towards a nuclear merchant ship

International Nuclear Information System (INIS)

Nicholson, R.L.R.; Llewelyn, G.I.W.; Farmer, A.A.

1976-01-01

The operation of nuclear merchant ships is likely to be attended by a number of constraints and requirements. Not all of these can be fully resolved until such ships come into use and the necessary experience and confidence have been acquired. But the timing of commercial introduction, if it comes about, will depend on the relative economics of nuclear versus fossil fuel propulsion, and the differences in turn depend in part on the operating costs particular to nuclear ships. A review of operation aspects is essential not only to commercial appraisal; each country whose trade may be carried in nuclear ships - whether it will build such ships or not - will have occasion to give some attention to the problems. It is an international problem and is, as noted later, being considered internationally. This paper; i) reviews some of the operational aspects as seen in the U.K.; ii) summarizes views received by the Nuclear Merchant Ship Unit (NMSU) from U.K. shipping, shipbuilding and nuclear industries on the prospects of a U.K. nuclear merchant ship. (author)

Safety Analysis Report for Packaging (SARP): USA/5790/BLF (ERDA-AL) and USA/5791/BLF (ERDA-AL)

International Nuclear Information System (INIS)

Griffin, J.F.; Bertram, R.E.; Blauvelt, R.K.; Edling, D.A.; Flanagan, T.M.; Peterson, J.B.; Prosser, D.L.

1976-01-01

The Safety Analysis Report for Packaging (SARP) satisfies the request of the U. S. Energy Research and Development Administration for a formal safety analysis of the two insulated drum shipping containers identified as USA/5790/BLF ERDA-AL and USA/5791/BLF ERDA-AL. Discussions of structural integrity, thermal resistance, radiation shielding and radiological safety, nuclear criticality safety, and quality control are included. Much of the information was previously submitted to ERDA/OSD/ALO and the Department of Transportation (DOT) and provided the basis for obtaining special permits DOT-SP-5790 and DOT-SP-5791 as well as the Interim Certificates of Compliance until the SARP could be prepared. Complete physical and technical descriptions of the packages are presented. Each package consists of a modified DOT Specification 2R cylindrical steel inner container centered within an insulated steel drum. The contents may be any radioactive materials which satisfy the requirements established in this SARP. A shipment of Plutonium-238 in the form of a solid oxide is evaluated in this SARP as an example. The results of the nuclear criticality safety analysis show how much of the fissile isotopes may be shipped as Fissile Class I, II, or III for each container. Design and development considerations, the test and evaluations required to prove the ability of the containers to withstand normal transportation conditions, and the sequence of four hypothetical accident conditions (free drop, puncture, thermal, and water immersion) are discussed

Shipping Information Pipeline

DEFF Research Database (Denmark)

Jensen, Thomas; Vatrapu, Ravi

2015-01-01

and national borders within international shipping which is a rather complex domain. The intellectual objective is to generate and evaluate the efficacy and effectiveness of design principles for inter-organizational information infrastructures in the international shipping domain that can have positive...

Navy Hospital ships in history

Directory of Open Access Journals (Sweden)

Sougat Ray

2017-01-01

Full Text Available Hospital ships are operated by the Naval forces in or near war zones to provide medical assistance to the wounded personnel of all nationalities and not be used for any military purpose. Hospital ships possibly existed in ancient times and the Athenian Navy had a ship named Therapia. However, it was only during the 17th century that it became a common practice for the naval squadrons to be accompanied by large ships with the facilities of carrying the wounded after each engagement. In 1860, the steamships HMS Melbourne and HMS Mauritius were equipped with genuine medical facilities. They were manned by the Medical Staff Corps and provided services to the British expedition to China. During the World War I and World War II, passenger ships were converted for use as hospital ships and were started to be used on a massive scale. RMS Aquitania and HMHS Britannic were two famous examples of hospital ships used extensively. Modern US hospital ships USNS Mercy and USNS Comfort are operated by Military Sealift Command of the US Navy. Their primary mission is to provide emergency on-site care for US combatant forces deployed in war or other operations.

Impact analysis of shipping casks

International Nuclear Information System (INIS)

Pfeiffer, P.A.; Kennedy, J.M.

1989-01-01

Shipping casks are being used in the United States Department of Energy to transport irradiated experiments, reactor fuel, radioactive waste, etc. One of the critical requirements in shipping cask analysis is the necessity to withstand severe impact environments. It is still conventional to develop the design and to verify the design requirements by hand calculations. Full three dimensional computations of impact scenarios have been performed but they are too expensive and time consuming for design purposes. Typically, on the order of more than an hour of CRAY time is required for a detailed, three dimensional analysis. The paper describes how simpler two- and three-dimensional models can be used to provide an intermediate level of detail between full three dimensional finite element calculations and hand calculations. The regulation that is examined here is: 10 CFR-71.73 hypothetical accident conditions, free drop. Free drop for an accident condition of a Class I package (approximate weight of 22,000 lb) is defined as a 30 foot drop onto a flat, essentially unyielding, horizontal surface, striking the surface in a position for which maximum damage is expected. Three free drop scenarios are analyzed to assess the integrity of the cask when subjected to large bending and axial stresses. These three drop scenarios are: (1) a thirty foot axial drop on either end, (2) a thirty foot oblique angle drop with the cask having several different orientations from the vertical with impact on the top end cask corner, and (3) a thirty foot side drop with simultaneous impact on the strength of the various components that comprise the cask. The predicted levels of deformation and stresses in the cask will be used to assess the potential damage level. 5 refs., 5 figs., 1 tab

Technique of stowing packages containing radioactive materials during maritime transportation

International Nuclear Information System (INIS)

Ringot, G.; Chevalier, G.; Tomachevsky, E.; Draulans, J.; Lafontaine, I.

1989-01-01

The Mont Louis accident (August 25, 1984 - North Sea), in which uraniumhexafluoride packages were involved, alarmed a large number of European competent authorities, including the Commission of European Communities. The latter sponsored in 1986-1987 a bibliographic data collection to obtain a first view on the problem. (C.E.C contracts n degree 86-B-7015-11-004-17 and 86-B-7015-11-005-17). The collected data supply the necessary basis for further work, aiming to increase the safety of transporting radioactive material by ship. The study collected the different deceleration values, used by the transport companies and defined the accident conditions to be considered. This work can serve as a basis for later research to end with the proposal of a code of good practice for stowing. The research-work has been carried out jointly by C.E.A.-France, I.P.S.N. at Fontenay-aux-Roses and by Transnubel S.A. Brussels Belgium. The preliminary research included two main tasks: a statistical analysis, a bibliographic study of ship accidents

Civilian nuclear ships

International Nuclear Information System (INIS)

Oelgaard, P.L.

1993-03-01

This report contains a review of the information available on nuclear powered ships, built for civilian purposes. In the introduction a short discussion is given of the reasons for the limited use of nuclear ships for these purposes. In the second section a brief review is presented of data for the three experimental/merchant ships build by the United States, Germany and Japan, i.e. NS Savannah, NS Otto Hahn and NS Mutsu. In the third section the Soviet/Russian icebreaker NS Lenin is considered. Its design, operational experience and the introduction of a new nuclear propulsion plant is reviewed. In the fourth section the newer Soviet/Russian icebreakers with nuclear propulsion are considered. Finally design of the Soviet/Russian icebreaker transport/container ship NS Sevmorput is reviewed in the fifth section. The future Russian plans for nuclear vessels for the arctic waters are briefly discussed. (au)

Safety Analysis Report for Packaging (SARP) of the Oak Ridge National Laboratory Garden Carrier No. 2. Revision 1

International Nuclear Information System (INIS)

Box, W.D.; Klima, B.B.; Seagren, R.D.; Shappert, L.B.; Watson, C.D.; Aramayo, G.A.

1979-08-01

An analytical evaluation of the Oak Ridge National Laboratory Garden Carrier No. 2 was made to demonstrate its compliance with the regulations governing off-site radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the cask complies with the applicable regulations

Safety Analysis Report for Packaging (SARP) of the Oak Ridge National Laboratory Garden Carrier No. 2. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Box, W.D.; Klima, B.B.; Seagren, R.D.; Shappert, L.B.; Watson, C.D.; Aramayo, G.A.

1979-08-01

An analytical evaluation of the Oak Ridge National Laboratory Garden Carrier No. 2 was made to demonstrate its compliance with the regulations governing off-site radioactive material shipping packages. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the cask complies with the applicable regulations.

An adaptive simulation model for analysis of nuclear material shipping operations

International Nuclear Information System (INIS)

Boerigter, S.T.; Sena, D.J.; Fasel, J.H.

1998-01-01

Los Alamos has developed an advanced simulation environment designed specifically for nuclear materials operations. This process-level simulation package, the Process Modeling System (ProMoS), is based on high-fidelity material balance criteria and contains intrinsic mechanisms for waste and recycle flows, contaminant estimation and tracking, and material-constrained operations. Recent development efforts have focused on coupling complex personnel interactions, personnel exposure calculations, and stochastic process-personnel performance criteria to the material-balance simulation. This combination of capabilities allows for more realistic simulation of nuclear material handling operations where complex personnel interactions are required. They have used ProMoS to assess fissile material shipping performance characteristics at the Los Alamos National Laboratory plutonium facility (TA-55). Nuclear material shipping operations are ubiquitous in the DOE complex and require the largest suite of varied personnel interacting in a well-timed manner to accomplish the task. They have developed a baseline simulation of the present operations and have estimated the operational impacts and requirement of the pit production mission at TA-55 as a result of the SSM-PEIS. Potential bottlenecks have been explored and mechanisms for increasing operational efficiency are identified

Safety analysis report for packaging (onsite) contaminated well cars

International Nuclear Information System (INIS)

Mercado, J.E.

1998-01-01

In support of past operations, railcars were used to ship irradiated fuel from the 100 Area fuel storage basins to the Plutonium Uranium Extraction (PUREX) Facility. There are two configurations for the packaging systems that transported the fuel: the Three-Well Cask Car, which is outfitted with three casks, and the taller, single well, New Production Reactor (NPR) Cask Car. In this document, these cask cars are referred to collectively as well cars. The purpose of this document is to evaluate and authorize the onsite transportation of well cars that contain significant levels of contamination. No irradiated fuel will be transported in the well cars. Neutron detection data confirmed that the well cars do not contain fuel. The intention is to move 14 retired well cars from their current locations in the 100 Area to a suitable storage location in the 200 Area. Each well car contains Type B quantities of radioactivity; so that the hazard of the transport operation is relatively low. This safety analysis report for packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the contaminated well cars meet the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for Hazardous Material Shipments for an onsite packaging. The scope of this document addresses the preparation and transportation of the contaminated well cars

Drug: D10442 [KEGG MEDICUS

Lifescience Database Archive (English)

Full Text Available inhibitor Chemical group: DG01818 ... Treatment of chronic hepatitis C infection HCV NS5A [CPD:C18292] ... CAS: 1256388-51-8 PubChem: 172232535 ChEBI: 85089 ChEMBL: CHEMBL2374220 ...

International Standardization in the Design of "Shore to Ship" - Power Supply Systems of Ships in Port

Science.gov (United States)

Tarnapowicz, Dariusz; German-Galkin, Sergiej

2018-03-01

The decisive source of air pollution emissions in ports is the berthed ships. This is primarily caused by the work of ship's autonomous generator sets. One way of reducing the air pollution emissions in ports is the supply of ships from electricity inland system. The main problem connected with the power connection of ships to the inland network is caused by different values of levels and frequencies of voltages in these networks (in various countries) in relation to different values of levels and frequencies of voltages present in the ship's network. It is also important that the source power can range from a few hundred kW up to several MW. In order to realize a universal „Shore to Ship" system that allows the connection of ships to the electricity inland network, the international standardization is necessary. This article presents the current recommendations, standards and regulations for the design of „Shore to Ship" systems.

Thermo-hydraulic characteristics of ship propulsion reactor in the conditions of ship motions and safety assessment

International Nuclear Information System (INIS)

Kobayashi, Michiyuki; Murata, Hiroyuki; Sawada, Kenichi; Inasaka, Fujio; Aya, Izuo; Shiozaki, Koki

1999-01-01

By inputting the experimental data, information and others on thermo-hydraulic characteristics of integrated ship propulsion reactor accumulated hitherto by the Ship Research Institute and some recent cooperation results into the nuclear ship engineering simulation system, it was conducted not only to contribute an improvement study on next ship reactor by executing general analysis and evaluation on motion characteristics under ship body motion conditions, safety at accidents, and others of the integrated ship reactor but also to investigate and prepare some measures to apply fundamental experiment results based on obtained here information to safety countermeasure of the nuclear ships. In 1997 fiscal year, on safety of the integrated ship propulsion reactor loading nuclear ship, by adding experimental data on unstable flow analysis and information on all around of the analysis to general data base fundamental program, development to intellectual data base program was intended; on effect of pulsation flow on thermo-hydraulic characteristics of ship propulsion reactor; after pulsation flow visualization experiment, experimental equipment was reconstructed into heat transfer type to conduct numerical analysis of pulsation flow by confirming validity of numerical analysis code under comparison with the visualization experiment results; and on thermo-hydraulic behavior in storage container at accident of active safety type ship propulsion reactor; a flashing vibration test using new apparatus finished on its higher pressurization at last fiscal year to examine effects of each parameter such as radius and length of exhausting nozzle and pool water temperature. (G.K.)

The Human Element and Autonomous Ships

Directory of Open Access Journals (Sweden)

Sauli Ahvenjärvi

2016-09-01

Full Text Available The autonomous ship technology has become a “hot” topic in the discussion about more efficient, environmentally friendly and safer sea transportation solutions. The time is becoming mature for the introduction of commercially sensible solutions for unmanned and fully autonomous cargo and passenger ships. Safety will be the most interesting and important aspect in this development. The utilization of the autonomous ship technology will have many effects on the safety, both positive and negative. It has been announced that the goal is to make the safety of an unmanned ship better that the safety of a manned ship. However, it must be understood that the human element will still be present when fully unmanned ships are being used. The shore-based control of a ship contains new safety aspects and an interesting question will be the interaction of manned and unmanned ships in the same traffic area. The autonomous ship technology should therefore be taken into account on the training of seafarers. Also it should not be forgotten that every single control algorithm and rule of the internal decision making logic of the autonomously navigating ship has been designed and coded by a human software engineer. Thus the human element is present also in this point of the lifetime navigation system of the autonomous ship.

Documentation for initial testing and inspections of Beneficial Uses Shipping System (BUSS) Cask

International Nuclear Information System (INIS)

Lundeen, J.E.

1994-01-01

The purpose of this report is to compile data generated during the initial tests and inspections of the Beneficial Uses Shipping System (BUSS) Cask. In addition, this report will verify that the testing criteria identified in section 8.1 of the BUSS Cask Safety Analysis Report for Packaging (SARP) was met. The BUSS Cask Model R-1 is a type B shipping container used for shipment of radioactive cesium-137 and strontium-90 capsules to Waste Encapsulation and Storage Facility (WESF). The BUSS Cask body and lid are each one-piece forgings fabricated from ASTM A473, Type 304 stainless steel. The primary purpose of the BUSS Cask is to provide shielding and confinement as well as impact, puncture, and thermal protection for the capsules under both normal and accident conditions. Chapter 8 of the BUSS Cask SARP requires several acceptance tests and inspections, each intended to evaluate the performance of different components of the BUSS Cask system, to be performed before its first use. The results of the tests and inspections required are included in this document

On impact mechanics in ship collisions

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup; Zhang, Shengming

1998-01-01

The purpose of this paper is to present analytical, closed-form expressions for the energy released for crushing and the impact impulse during ship collisions. Ship–ship collisions, ship collisions with rigid walls and ship collisions with flexible offshore structures are considered. The derived ...

Certification of ERDA contractors' packaging with respect to compliance with DOT specification 7A performance requirements

International Nuclear Information System (INIS)

Edling, D.A.; Griffin, J.F.

1975-01-01

The purpose of this study was to have one ERDA contractor: (1) compile a list of specification packagings, proposed by ERDA contractors, for shipping Type A quantities of radioactive material, and (2) analyze these packages for conformance to Specification 7A requirements. This study was divided into two phases. Phase I provides a report on those packages which could be shown, based on existing test data and engineering analyses, to conform to DOT Specification 7A packaging requirements. The results of Phase I are discussed in detail in the publication, ''Certification of AEC Contractor's Packagings With Respect to Compliance with DOT Specification 7A Performance Requirements -- Phase I Summary Report,'' D. A. Edling, H. E. Meyer and G. L. Phillabaum (Schedule 189C, May 26, 1974). The objectives of Phase II were: (1) identification of packages from Phase I for which available information was not adequate for certification. (Those specification containers used by ERDA contractors and those containers for which adequate information was available for certification are listed in the Phase I summary report.); (2) identification of specific test/engineering analysis data required; (3) generation/procurement of these data; and (4) documentation of study results for use by all ERDA contractors and private industry. The results of Phase II of the study are presented. (U.S.)

Advanced Demonstration of Motion Correction for Ship-to-Ship Passive Inspections

Energy Technology Data Exchange (ETDEWEB)

Ziock, Klaus-Peter [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Boehnen, Chris Bensing [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ernst, Joseph [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2013-09-30

Passive radiation detection is a key tool for detecting illicit nuclear materials. In maritime applications it is most effective against small vessels where attenuation is of less concern. Passive imaging provides: discrimination between localized (threat) and distributed (non-threat) sources, removal of background fluctuations due to nearby shorelines and structures, source localization to an individual craft in crowded waters, and background subtracted spectra. Unfortunately, imaging methods cannot be easily applied in ship-to-ship inspections because relative motion of the vessels blurs the results over many pixels, significantly reducing sensitivity. This is particularly true for the smaller water craft where passive inspections are most valuable. In this project we performed tests and improved the performance of an instrument (developed earlier under, “Motion Correction for Ship-to-Ship Passive Inspections”) that uses automated tracking of a target vessel in visible-light images to generate a 3D radiation map of the target vessel from data obtained using a gamma-ray imager.

Packaging, Transportation and Recycling of NPP Condenser Modules - 12262

Energy Technology Data Exchange (ETDEWEB)

Polley, G.M. [Perma-Fix Environmental Services, 575 Oak Ridge Turnpike, Oak Ridge, TN 37830 (United States)

2012-07-01

Perma-Fix was awarded contract from Energy Northwest for the packaging, transportation and disposition of the condenser modules, water boxes and miscellaneous metal, combustibles and water generated during the 2011 condenser replacement outage at the Columbia Generating Station. The work scope was to package the water boxes and condenser modules as they were removed from the facility and transfer them to the Perma-Fix Northwest facility for processing, recycle of metals and disposition. The condenser components were oversized and overweight (the condenser modules weighed ∼102,058 kg [225,000 lb]) which required special equipment for loading and transport. Additional debris waste was packaged in inter-modals and IP-1 boxes for transport. A waste management plan was developed to minimize the generation of virtually any waste requiring landfill disposal. The Perma-Fix Northwest facility was modified to accommodate the ∼15 m [50-ft] long condenser modules and equipment was designed and manufactured to complete the disassembly, decontamination and release survey. The condenser modules are currently undergoing processing for free release to a local metal recycler. Over three millions pounds of metal will be recycled and over 95% of the waste generated during this outage will not require land disposal. There were several elements of this project that needed to be addressed during the preparation for this outage and the subsequent packaging, transportation and processing. - Staffing the project to support 24/7 generation of large components and other wastes. - The design and manufacture of the soft-sided shipping containers for the condenser modules that measured ∼15 m X 4 m X 3 m [50 ft X 13 ft X 10 ft] and weighed ∼102,058 kg [225,000 lbs] - Developing a methodology for loading the modules into the shipping containers. - Obtaining a transport vehicle for the modules. - Designing and modifying the processing facility. - Movement of the modules at the processing

Decision of the National Board of Navigation on the Carriage of Dangerous Goods in Ships

International Nuclear Information System (INIS)

1980-01-01

This is an unofficial English translation of a decision, which was made in accordance with Section 12 of Decree No. 357 of 16th May 1980 on the Carriage of Dangerous Goods in Ships. It adopts by reference the IMO/IMDG Code with the packaging Annex and Amendments 1 - 21. Where the National Board of Navigation has not provided otherwise, the Code shall be applied to vessels carrying dangerous goods, to the classification, packing, marketing and handling of dangerous goods and the stowage of such goods on board, and to documents related to carriage of dangerous goods. The decision applies to vessels engaged in traffic in Finnish territorial waters and to all Finnish vessels, even when operating outside Finnish territorial waters. The decision designates the Finnish Centre for Radiation and Nuclear Safety as the competent authority where approval certificates for transport, packages or containers of radioactive materials are required. (NEA) [fr

High cost for drilling ships

International Nuclear Information System (INIS)

Hooghiemstra, J.

2007-01-01

Prices for the rent of a drilling ship are very high. Per day the rent is 1% of the price for building such a ship, and those prices have risen as well. Still, it is attractive for oil companies to rent a drilling ship [nl

Accidents in nuclear ships

Energy Technology Data Exchange (ETDEWEB)

Oelgaard, P L [Risoe National Lab., Roskilde (Denmark); [Technical Univ. of Denmark, Lyngby (Denmark)

1996-12-01

This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10{sup -3} per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au).

Accidents in nuclear ships

International Nuclear Information System (INIS)

Oelgaard, P.L.

1996-12-01

This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10 -3 per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au)

Trends of shipping markets development

Directory of Open Access Journals (Sweden)

Tomasz Nowosielski

2012-06-01

Full Text Available Shipping markets are dependent on international trade transactions that generate transport needs. These needs can dynamically change depending on global natural resources and commodity markets situation. The changes affecting shipping markets can also be caused by changes to the existing cargo flows and by establishing new ones in different geographies. It is anticipated that in the future shipping markets will change, visible by a decline in shipping in North America and Europe and an increase in Asia.

Use of Insulated Covers over Product Crates to Reduce Losses in Amaranth during Shipping Delays

Directory of Open Access Journals (Sweden)

Lizanne Wheeler

2015-12-01

Full Text Available Amaranth is a leafy vegetable with high nutrient content which is sensitive to temperature and low relative humidity. Delays in shipment to market may result in significant losses, therefore improved packaging to minimize mechanical damage and reduce moisture loss are desirable. Amaranth was stored in three types of consumer packages, bunches, clamshells and thin plastic bags, within vented plastic crates. Pallet loads were either covered with insulated material or not, while awaiting transportation. Results indicated covering pallets improved the color and overall quality while reducing weight loss and wilting. Covered crates had a “good” (7.6/9.0 overall quality while uncovered averaged 5.5/9.0 or “moderate” quality. There were significant differences in consumer package type, with the bagged amaranth having almost “excellent” quality (8.8/9.0 compared to “good-fair” quality in clamshells (6.2/9.0 and “poor-fair” quality in the control bunches (4.7/9.0. Amaranth stored in thin plastic bags was better in quality and color, with less weight loss and wilting, however, temperatures at the end of six hours of storage were higher and this may lead to microbial growth. Storage of amaranth in thin bags or clamshell packages, within plastic crates covered with insulated pallet covers while awaiting shipping resulted in improved overall quality and color.

Advanced ship systems condition monitoring for enhanced inspection, maintenance and decision making in ship operations

OpenAIRE

Lazakis, Iraklis; Dikis, Konstantinos; Michala, Anna Lito; Theotokatos, Gerasimos

2016-01-01

Structural and machinery failures in the day-to-day ship operations may lead to major accidents, endangering crew and\\ud passengers onboard, posing a threat to the environment, damaging the ship itself and having a great impact in terms of business\\ud losses. In this respect, this paper presents the INCASS (Inspection Capabilities for Enhanced Ship Safety) project which aims\\ud bringing an innovative solution to the ship inspection regime through the introduction of enhanced inspection of shi...

Qualification testing facility for packages to be used for transport and storage of radioactive materials

International Nuclear Information System (INIS)

Vieru, Gheorghe

2009-01-01

The radioactive materials (RAM) packaging have to comply to all modes and transport condition, routine or in accident conditions possibly to occur during transportation operations. It is well known that the safety in the transport of RAM is dependent on packaging appropriate for the contents being shipped rather than on operational and/or administrative actions required for the package. The quality of these packages - type A, B or C has to be proved by performing qualification tests in accordance with the ROMANIAN nuclear regulation conditions provided by CNCAN Order no. 357/22.12.2005- 'Norms for a Safe Transport of Radioactive Material', the IAEA Vienna Recommendation stipulated in the Safety standard TS-R-1- Regulation for the Safe Transport of Radioactive Material, 2005 Edition, and other applicable international recommendations. The paper will describe the components of the designed testing facilities, and the qualification testing to be performed for all type A, B and C packages subjected to the testing. In addition, a part of the qualification tests for a package (designed and manufactured in INR Pitesti) used for transport and storage of spent fuel LEU elements of a TRIGA nuclear reactor will be described and analyzed. Quality assurance and quality controls measures taken in order to meet technical specification provided by the design are also presented and commented. The paper concludes that the new Romanian Testing Facilities for RAM packages will comply with the national safe standards as well as with the IAEA applicable recommendation provided by the TS-R-1 safety standard. (author)

Guide to ship sanitation

National Research Council Canada - National Science Library

2011-01-01

"The third edition of the Guide to Ship Sanitation presents the public health significance of ships in terms of disease and highlights the importance of applying appropriate control measures"--Back cover...

The IRSN experience feedback for the transport package design safety appraisals

International Nuclear Information System (INIS)

Sert, G.

2007-01-01

The activity of transportation of radioactive materials is in constant evolution; air transport of radio elements for medical use is growing rapidly as well as transport of instruments equipped with radioactive sources for inspections of buildings (controls of presence of lead in paintings) and in industry (non destructive examination of welding by gammagraphy, controls of density on building sites). Transports associated with the recycling of plutonium for the production of electricity by nuclear energy are now accomplished in routine. Globally, 900.000 packages are shipped each year in France; among them, approximately 100.000 packages belong to the category for which design approval is required. To maintain a high level of safety for this activity by limiting the probability of occurrence, the severity and consequences of the incidents and accidents, strict rules are implemented by users under the control of the Safety Authority According to the systematic approach of defence in depth, which is defined by the three principles of safety in design, of operational reliability and of effectiveness of emergency response, the robustness of the design of the package is of primary importance. It is based on regulatory requirements relating to the functions of safety (containment of radioactivity, protection against radiation and prevention of the risks of criticality) that must be ensured by the package in conditions of transport as well as in accident conditions. These rules and the way of applying them evolve with time. Indeed, on the one hand the regulation is reexamined periodically; on the other hand, the technical knowledge on the behaviour of the packages subject to the above mentioned conditions and the means of evaluation of this behaviour progress permanently

Packaging and labeling of pharmaceutical products obtained from the internet.

Science.gov (United States)

Veronin, Michael

2011-02-15

For patients, the prescription container label may be the only source of instructions on how to take their medicines. In the United States, the legal requirements for a prescription label are set by federal law and state statutes. The container should be comparable to that which manufacturers use to package drug products and should preserve a product's identity, strength, quality, and purity and prevent contamination. Safety features such as a child-resistant closure should be provided. Pharmaceutical products purchased from international online pharmacies are not approved by the Food and Drug Administration (FDA) and may not meet US guidelines for labeling and packaging. The study objective was to determine whether commonly purchased pharmaceutical products obtained from international online pharmacies are comparable to products dispensed in the United States with regard to labeling and packaging. During March 2006 through January 2007, 41 pharmaceutical oral dosage form samples were obtained from international Internet pharmacy websites for evaluation: 18 generic simvastatin samples, 18 generic amlodipine samples, and 5 generic sildenafil samples. Contents for each package were observed and recorded and comparison of the prescription labeling and packaging of these products was made with prescription labeling and packaging requirements in the United States. Of the 41 drug products obtained from online pharmacies from 12 different countries, only 1 product (from Canada) would meet both labeling and packaging guidelines for products dispensed in the United States. Of those not meeting the requirements, 7 were dispensed in paper envelopes with label affixed that was either handwritten or typed and contained missing information such as name and address of dispenser, name of prescriber, name of patient, and directions for use. Another 3 products did not have a label affixed to the drug product, but information was printed on a paper document enclosed in the shipping

Cybersecurity Framework for Ship Industrial Control System

OpenAIRE

Maule, R. William; Hake, Joseph

2016-01-01

Ship mechanical and electrical control systems, and the communications grid through which these devices operate, are a high priority concern for Navy leadership. Ship systems use microprocessor-based controls to interface with physical objects, and Programmable Logic Controllers (PLCs) to automate ship electromechanical processes. Ship operations are completely dependent on these devices. The commercial security products upon which ships depend do not work on ICS, leaving ships vulnerable. Th...

Containment of spills from ships

International Nuclear Information System (INIS)

Engerer, M.J.

1992-01-01

Oil escaping from a ship is contained within a limited area surrounding the ship by means of a flexible ring structure. The ring structure is stored in a collapsed state in a compartment extending around the ship. In response to an oil spill, the ring structure is dropped from the compartment and immediately surrounds the ship. A circular inflatable flotation section of the ring structure is charged with gas under pressure. The gas is supplied from a bottle cascade aboard the ship, through lines preconnected to the flotation section and paid out from free-wheeling reels. The flotation section supports a thin circumferential wall of predetermined height that submerges and assumes a vertical cylinder-like shape surrounding the escaping oil. The oil floats within the confines of the ring structure, and the ring structure is progressively expanded to a predetermined size selected to accommodate the total volume of oil carried by the ship. When the ring structure achieves its expanded state, pressure in the flotation section is raised to render the structure relatively rigid and resistant to collapse in response to wave action. Oil can be removed from the interior of the ring structure by recovery ships using suction lines or other conventional recovery methods. 12 figs

Real-Time Simulation of Ship-Structure and Ship-Ship Interaction

DEFF Research Database (Denmark)

Lindberg, Ole; Glimberg, Stefan Lemvig; Bingham, Harry B.

2013-01-01

, because it is simple, easy to implement and computationally efficient. Multiple many-core graphical processing units (GPUs) are used for parallel execution and the model is implemented using a combination of C/C++, CUDA and MPI. Two ship hydrodynamic cases are presented: Kriso Container Carrier at steady...

An absorbent for an application to a package for a liquid radioactive isotope for medical usage

International Nuclear Information System (INIS)

Bang, K.S.; Lim, S.P.; Lee, J.C.; Seo, K.S.; Han, H.S.

2004-01-01

A radioactive isotope has to be safely transport from the producing center to the consuming center. The shipping package to safely transport the radioactive isotope should be able to withstand the prescribed conditions by law. In the field of nuclear medicine, the radioactive isotope is used in a liquid or capsule form. A Type A package, which is to transport liquid radioactive materials, shall be provided with a containment system composed of primary inner and secondary outer containment components or shall be provided with sufficient absorbent material to absorb twice the volume of the liquid contents. Hospitals prefer to use not only convenient but also re-usable packages. To apply an absorbent material to the Type A package, that is to transport liquid radioactive isotope, the free absorbency of the absorbents was estimated. In the case of a liquid with NaOH 0.4%, the free absorbency of the melanine form was the most superior at 91 g/g. In the case of a liquid with Na 0.9%, the free absorbency of the melanine form was the most excellent at 88 g/g also

Package Flow Model and its fuzzy implementation for simulating nuclear reactor system dynamics

International Nuclear Information System (INIS)

Matsuoka, Hiroshi; Ishiguro, Misako.

1996-01-01

A simple intuitive simulation model, which we call 'Package Flow Model', has been developed to evaluate physical processes in nuclear reactor system from a macroscopic point of view. In the previous paper, we showed the physical process of each energy generation and transfer stage in a PWR could be modeled by PFM, and its dynamics could be approximately simulated by fuzzy implementation. In this paper, a PFMs network approach for a total PWR system simulation is proposed and some transients of nuclear ship 'MUTSU' reactor system are evaluated. The simulated results are consistent with those from Nuclear Ship Engineering Simulation System developed by JAERI. Furthermore, a visual representation method is proposed to intuitively capture the profile of fuel safety transient. Using the PFMs network, we can handily calculate the transient phenomena of the system even by a notebook-type personal computer. In addition, we can easily interpret the results of calculation surveying a small number of parameters. (author)

EX1001 Ship Shakedown (EX1001, EM302) on NOAA Ship Okeanos Explorer in Hawaiian Islands

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The ship has been alongside for repairs and leave since November, 2009. The ship shakedown cruise is scheduled to provide an opportunity for the ship to get underway...

46 CFR 148.02-1 - Shipping papers.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Shipping papers. 148.02-1 Section 148.02-1 Shipping... MATERIALS IN BULK Vessel Requirements § 148.02-1 Shipping papers. (a) Carriers may not accept for..., unless the hazardous materials offered for such shipment is accompanied by a shipping paper on which the...

Safety analysis report for packaging (Oak Ridge Y-12 Plant Model DT-14A package for enriched uranium), Y/DD-326 Supplement No. 1 (Rev. 0)

International Nuclear Information System (INIS)

Cadelli, G.; Kennedy, W.R. Jr.

1986-01-01

This Supplement to the Safety Analysis Report Y/DD-326 [1.4.1] was prepared in accordance with US NRC Regulatory Guide 7.9 to address the Naval Fuel contents to be shipped in the DT-14A packaging. New chapters were written for Shielding, Critcality and Quality Assurance. Independent reviews were obtained for each of these chapters and for a product leakage analysis referenced in Chapter 7.0 of this document. Other chapters invoke the Y/DD-326 SARP with minor changes or additions as indicated in the Supplement. All references to form or composition of the fuel are classified Confidential NNPI in the interest of national security

Naval Ship Database: Database Design, Implementation, and Schema

Science.gov (United States)

2013-09-01

ClassId Class identifier Name Ship name Pendant Ship pendant CommissionDate Ship commission date DecommissionDate Ship decommission date; NULL if still...active FlagshipId Ship Id of the ship Figure 3: Ship table definition Table 3: Ship table example rows Id Prefix ClassId Name Pendant ...computation if required. A bridged connection will allow computation analysis to be done in Matlab and allow the processed data to be imported back

Ship Technology Workshop Materials from Collaboration with Mexico to Reduce Emissions from Ships

Science.gov (United States)

On September 26, 2012, a ship technology seminar was held to provide Mexican stakeholders with information about some of the ship technologies needed to meet the requirements of MARPOL Annex VI and an ECA.

Use of commercial robotics in radioactive waste shipping and receiving

International Nuclear Information System (INIS)

Berger, J.D.

1985-01-01

Radioactive waste shipping and receiving facilities presently planned for commercial and defense nuclear waste will handle waste packages at frequencies far in excess of those in common practice today. Unacceptable personnel exposure to ionizing radiation is projected to occur if current limits for radiation levels at the cask surface and current handling methods are used. To reduce these exposure levels, alternate handling methods are being developed and demonstrated. The production nature of cask receiving operations suggests commercial robotics be incorporated into a remote handling system to reduce predicted worker exposure to acceptable levels, while maintaining or increasing throughput. The first phase of cask handling system development culminated in a proof-of-principle test demonstrating the feasibility of performing cask receiving and unloading operations in a remote and partially automated manner. 6 refs., 12 figs

Fast ship

OpenAIRE

Keuning, J.A.

2014-01-01

The invention concerns a ship whereby the hull and the mechanical propulsion device are designed such that the Froude number is larger than 0.5. In the aft ship the hull has a bottom with V-shaped bottom surfaces with a deadrise angle that is less than 40 degrees and the hull has substantially vertical sides. In the hull are a passenger compartment and a trim tank. The trim tank volume is such that the weight of a filled trim tank is more than 30 % of the weight of displacement of the hull wi...

46 CFR 151.45-7 - Shipping papers.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Shipping papers. 151.45-7 Section 151.45-7 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Operations § 151.45-7 Shipping papers. Each barge carrying... towing vessel shall either have a copy of the shipping papers for each barge in his tow or he shall make...

Radioisotope thermoelectric generator load and unload sequence from the licensed hardware package system and the trailer system

International Nuclear Information System (INIS)

Reilly, M.A.

1995-01-01

The Radioisotope Thermoelectric Generator Transportation System, designated as System 100, comprises four major systems. The four major systems are designated as the Packaging System (System 120), Trailer System (System 140), Operations and Ancillary Equipment System (System 160), including the Radioisotope Thermoelectric Generator Transportation System packaging is licensed (regularoty) hardware, certified by the U.S. Department of Energy to be in accordance with Title 10, Code of Federal Regulations, Part 71 (10 CFR 71). System 140, System 160, and System 180 are nonlicensed (nonregulatory) hardware. This paper focuses on the required interfaces and sequencing of events required by these systems and the shipping and receiving facilities in preparation of the Radioisotope Thermoelectric Generator for space flight. copyright 1995 American Institute of Physics

The investigation of ship maneuvering with hydrodynamic effects between ships in curved narrow channel

Directory of Open Access Journals (Sweden)

Chun-Ki Lee

2016-01-01

Full Text Available The hydrodynamic interaction between two large vessels can't be neglected when two large vessels are closed to each other in restricted waterways such as in a harbor or narrow channel. This paper is mainly concerned with the ship maneuvering motion based on the hydrodynamic interaction effects between two large vessels moving each other in curved narrow channel. In this research, the characteristic features of the hydrodynamic interaction forces between two large vessels are described and illustrated, and the effects of velocity ratio and the spacing between two vessels are summarized and discussed. Also, the Inchon outer harbor area through the PALMI island channel in Korea was selected, and the ship maneuvering simulation was carried out to propose an appropriate safe speed and distance between two ships, which is required to avoid sea accident in confined waters. From the inspection of this investigation, it indicates the following result. Under the condition of SP12≤0.5L, it may encounter a dangerous tendency of grounding or collision due to the combined effect of the interaction between ships and external forces. Also considering the interaction and wind effect as a parameter, an overtaken and overtaking vessel in narrow channel can navigate while keeping its own original course under the following conditions; the lateral separation between two ships is about kept at 0.6 times of ship length and 15 degrees of range in maximum rudder angle. On the other hand, two ships while overtaking in curved narrow channel such as Inchon outer harbor in Korea should be navigated under the following conditions; SP12 is about kept at 1.0 times of ship length and the wind velocity should not be stronger than 10 m/s.

Optimization in liner shipping

DEFF Research Database (Denmark)

Brouer, Berit Dangaard; Karsten, Christian Vad; Pisinger, David

2017-01-01

Seaborne trade is the lynchpin in almost every international supply chain, and about 90% of non-bulk cargo worldwide is transported by container. In this survey we give an overview of data-driven optimization problems in liner shipping. Research in liner shipping is motivated by a need for handling...... still more complex decision problems, based on big data sets and going across several organizational entities. Moreover, liner shipping optimization problems are pushing the limits of optimization methods, creating a new breeding ground for advanced modelling and solution methods. Starting from liner...... shipping network design, we consider the problem of container routing and speed optimization. Next, we consider empty container repositioning and stowage planning as well as disruption management. In addition, the problem of bunker purchasing is considered in depth. In each section we give a clear problem...

Ship construction and welding

CERN Document Server

Mandal, Nisith R

2017-01-01

This book addresses various aspects of ship construction, from ship types and construction materials, to welding technologies and accuracy control. The contents of the book are logically organized and divided into twenty-one chapters. The book covers structural arrangement with longitudinal and transverse framing systems based on the service load, and explains basic structural elements like hatch side girders, hatch end beams, stringers, etc. along with structural subassemblies like floors, bulkheads, inner bottom, decks and shells. It presents in detail double bottom construction, wing tanks & duct keels, fore & aft end structures, etc., together with necessary illustrations. The midship sections of various ship types are introduced, together with structural continuity and alignment in ship structures. With regard to construction materials, the book discusses steel, aluminum alloys and fiber reinforced composites. Various methods of steel material preparation are discussed, and plate cutting and form...

Potential of biofuels for shipping. Final Report

Energy Technology Data Exchange (ETDEWEB)

Florentinus, A.; Hamelinck, C.; Van den Bos, A.; Winkel, R.; Cuijpers, M. [Ecofys Netherlands, Utrecht (Netherlands)

2012-01-15

Biofuels could be one of the options to realize a lower carbon intensity in the propulsion of ships and also possibly reduce the effect of ship emissions on local air quality. Therefore, EMSA, the European Maritime Safety Agency, is evaluating if and how biofuels could be used in the shipping sector as an alternative fuel. To determine the potential of biofuels for ships, a clearer picture is needed on technical and organizational limitations of biofuels in ships, both on board of the ship as in the fuel supply chain to the ship. Economic and sustainability analysis of biofuels should be included in this picture, as well as an overview on current and potential policy measures to stimulate the use of biofuels in shipping. Ecofys has determined the potential of biofuels, based on analysis of collected data through literature review, own expertise and experiences, direct communication with EMSA, research publications, market developments based on press and other media, and consultations with relevant stakeholders in the shipping market.

Safety analysis report for the TRUPACT-II shipping package (condensed version). Volume 1, Rev. 14

International Nuclear Information System (INIS)

1994-10-01

The condensed version of the TRUPACT-II Contact Handled Transuranic Waste Safety Analysis Report for Packaging (SARP) contains essential material required by TRUPACT-II users, plus additional contents (payload) information previously submitted to the U.S. Nuclear Regulatory Commission. All or part of the following sections, which are not required by users of the TRUPACT-II, are deleted from the condensed version: (i) structural analysis, (ii) thermal analysis, (iii) containment analysis, (iv) criticality analysis, (v) shielding analysis, and (vi) hypothetical accident test results

Safety analysis report for the TRUPACT-II shipping package (condensed version). Volume 1, Rev. 14

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-10-01

The condensed version of the TRUPACT-II Contact Handled Transuranic Waste Safety Analysis Report for Packaging (SARP) contains essential material required by TRUPACT-II users, plus additional contents (payload) information previously submitted to the U.S. Nuclear Regulatory Commission. All or part of the following sections, which are not required by users of the TRUPACT-II, are deleted from the condensed version: (i) structural analysis, (ii) thermal analysis, (iii) containment analysis, (iv) criticality analysis, (v) shielding analysis, and (vi) hypothetical accident test results.

Thermo-hydraulic characteristics of ship propulsion reactor in the conditions of ship motions and safety assessment

International Nuclear Information System (INIS)

Kobayashi, Michiyuki; Aya, Izuo; Inasaka, Fujio; Murata, Hiroyuki; Odano, Naoteru; Shiozaki, Koki

1998-01-01

A research project from 1995-1999 had a plan to make experimental studies on (1) safety of nuclear ship loaded with an integral ship propulsion reactor (2) effects of pulsating flow on the thermo-hydraulic characteristics of ship propulsion reactor and (3) thermo-hydraulic behaviors of the reactor container at the time of accident in a passively safe ship propulsion reactor. Development of a data base for ship propulsion reactor was attempted using previous experimental data on the thermo-hydraulic characteristics of the reactor in the institute in addition to the present results aiming to make general analytical evaluation for the safety of the engineering-simulation system for nuclear ship. A general data base was obtained by integrating the data list and the analytical program for static characteristics. A test equipment which allows to visualize the pulsating flow was produced and visualization experiments have started. (M.N.)

A Fully Nonlinear, Dynamically Consistent Numerical Model for Solid-Body Ship Motion. I. Ship Motion with Fixed Heading

Science.gov (United States)

Lin, Ray-Quing; Kuang, Weijia

2011-01-01

In this paper, we describe the details of our numerical model for simulating ship solidbody motion in a given environment. In this model, the fully nonlinear dynamical equations governing the time-varying solid-body ship motion under the forces arising from ship wave interactions are solved with given initial conditions. The net force and moment (torque) on the ship body are directly calculated via integration of the hydrodynamic pressure over the wetted surface and the buoyancy effect from the underwater volume of the actual ship hull with a hybrid finite-difference/finite-element method. Neither empirical nor free parametrization is introduced in this model, i.e. no a priori experimental data are needed for modelling. This model is benchmarked with many experiments of various ship hulls for heave, roll and pitch motion. In addition to the benchmark cases, numerical experiments are also carried out for strongly nonlinear ship motion with a fixed heading. These new cases demonstrate clearly the importance of nonlinearities in ship motion modelling.

A Nonlinear Ship Manoeuvering Model: Identification and adaptive control with experiments for a model ship

Directory of Open Access Journals (Sweden)

Roger Skjetne

2004-01-01

Full Text Available Complete nonlinear dynamic manoeuvering models of ships, with numerical values, are hard to find in the literature. This paper presents a modeling, identification, and control design where the objective is to manoeuver a ship along desired paths at different velocities. Material from a variety of references have been used to describe the ship model, its difficulties, limitations, and possible simplifications for the purpose of automatic control design. The numerical values of the parameters in the model is identified in towing tests and adaptive manoeuvering experiments for a small ship in a marine control laboratory.

Packaging Solutions : Delivering customer value through Logistical Packaging: A Case Study at Stora Enso Packaging

OpenAIRE

Shan, Kun; Julius, Joezer

2015-01-01

AbstractBackground;Despite of the significant role of packaging within logistics and supply chain management, packaging is infrequently studied as focal point in supply chain. Most of the previous logistics research studies tend to explain the integration between packaging and logistics through logistical packaging. In very rare cases, the studies mentioned about customer value. Therefore the major disadvantage of these studies is that, they didn’t consider logistical packaging and customer v...

Effect of Buffer Bow Structure in Ship-Ship Collision

DEFF Research Database (Denmark)

Yamada, Yasuhira; Endo, Hisayoshi; Pedersen, Preben Terndrup

2008-01-01

tankers, the introduction of buffer bulbous bows has been proposed. Relatively soft buffer bows absorb part of the kinetic energy of the striking ship before penetrating the inner hull of the struck vessel. The purpose of the present paper is to verify the effectiveness of a prototype buffer bulbous bow......) and the forward velocity of the struck ship on the collapse mode of the bow of the striking vessel are investigated. Collapse modes, contact forces and energy absorption capabilities of the buffer bows are compared with those of conventional bows....

Identification of Dynamically Positioned Ships

Directory of Open Access Journals (Sweden)

Thor I. Fossen

1996-04-01

Full Text Available Todays model-based dynamic positioning (DP systems require that the ship and thruster dynamics are known with some accuracy in order to use linear quadratic optical control theory. However, it is difficult to identify the mathematical model of a dynamically posititmed (DP ship since the ship is not persistently excited under DP. In addition the ship parameter estimation problem is nonlinear and multivariable with only position and thruster state measurements available for parameter estimation. The process and measurement noise must also be modeled in order to avoid parameter drift due to environmental disturbances and sensor failure. This article discusses an off-line parallel extended Kalman filter (EKF algorithm utilizing two measurement series in parallel to estimate the parameters in the DP ship model. Full-scale experiments with a supply vessel are used to demonstrate the convergence and robustness of the proposed parameter estimator.

How we shipped our flip and standard too

International Nuclear Information System (INIS)

Deigl, H.J.; Feltz, D.E.

1984-01-01

This paper highlights the planning and handling activities for the shipment of irradiated TRIGA fuel from Texas A and M University to the Argonne National Lab/West (ANL/West) reactor facility at Idaho Falls, Idaho. Attention is focused on the enormous time spent on the planning and preparations prior to the shipment. The actual handling time at the NSCR for three shipping packages containing a total 51 elements was only 4 days, but, the time spent in planning and preparation exceeded 16 months. The fuel was transferred for shipment without incident - and from a health physics standpoint the exercise went very well. Whole body exposures and hand doses were minimal for such a large undertaking. ANL/West health physicists reported contamination of the lifting devices for the HFIR when they received the cask. These pieces were wipe tested and contamination was found to be less than 200 dpm. If they were contaminated we were extremely fortunate during handling not to contaminate our facility or personnel

Packaging fluency

DEFF Research Database (Denmark)

Mocanu, Ana; Chrysochou, Polymeros; Bogomolova, Svetlana

2011-01-01

Research on packaging stresses the need for packaging design to read easily, presuming fast and accurate processing of product-related information. In this paper we define this property of packaging as “packaging fluency”. Based on the existing marketing and cognitive psychology literature on pac...

46 CFR 167.05-25 - Nautical school ship.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Nautical school ship. 167.05-25 Section 167.05-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Definitions § 167.05-25 Nautical school ship. The term nautical school ship means a vessel operated by or in connection with a nautical school...

Liner Shipping Fleet Repositioning

DEFF Research Database (Denmark)

Tierney, Kevin; Jensen, Rune Møller

2011-01-01

Liner shipping fleet repositioning consists of moving vessels between services in a liner ship- ping network in order to better orient the overall network to the world economy, and to ensure the proper maintenance of vessels. Thus, fleet repositioning involves sailing and loading activities subject...

Thermal testing of packages for transport of radioactive wastes

International Nuclear Information System (INIS)

Koski, J.A.

1994-01-01

Shipping containers for radioactive materials must be shown capable of surviving tests specified by regulations such as Title 10, Code of Federal Regulations, Part 71 (called 10CFR71 in this paper) within the United States. Equivalent regulations hold for other countries such as Safety Series 6 issued by the International Atomic Energy Agency. The containers must be shown to be capable of surviving, in order, drop tests, puncture tests, and thermal tests. Immersion testing in water is also required, but must be demonstrated for undamaged packages. The thermal test is intended to simulate a 30 minute exposure to a fully engulfing pool fire that could occur if a transport accident involved the spill of large quantities of hydrocarbon fuels. Various qualification methods ranging from pure analysis to actual pool fire tests have been used to prove regulatory compliance. The purpose of this paper is to consider the alternatives for thermal testing, point out the strengths and weaknesses of each approach, and to provide the designer with the information necessary to make informed decisions on the proper test program for the particular shipping container under consideration. While thermal analysis is an alternative to physical testing, actual testing is often emphasized by regulators, and this report concentrates on these testing alternatives

Hydrodynamics of Ship Propellers

DEFF Research Database (Denmark)

Breslin, John P.; Andersen, Poul

This book deals with flows over propellers operating behind ships, and the hydrodynamic forces and moments which the propeller generates on the shaft and on the ship hull.The first part of the text is devoted to fundamentals of the flow about hydrofoil sections (with and without cavitation...... of an intermittently cavitating propeller in a wake and the pressures and forces it exerts on the shaft and on the ship hull is examined. A final chapter discusses the optimization of efficiency of compound propulsors. The authors have taken care to clearly describe physical concepts and mathematical steps. Appendices...

Dose assessment for public at the hypothetical submergence of a fresh MOX fuel package

International Nuclear Information System (INIS)

Tsumune, Daisuke; Saegusa, Toshiari; Suzuki, Hiroshi; Maruyama, Koki

2000-01-01

For the structure and equipment of transport ships for fresh MOX fuels, there is a special safety standard called the INF Code of IMO (International Maritime Organization). For transport of radioactive materials, there is a safety standard stipulated in Regulations for the Safe Transport of Radioactive Material issued by IAEA (International Atomic Energy Agency). Under those code and standard, fresh MOX fuel is transported safety on the sea. To gain the public acceptance for this transport, a dose assessment has been made by assuming that a fresh MOX fuel package might be sunk into the sea by unknown reasons. In the both cases for a package sunk at the coastal region and for that sunk at the ocean, the evaluated result of the dose equivalent by radiation exposure to the public are far below the dose equivalent limit of the ICRP recommendation (1 mSv/year). (author)

International climate policy : consequences for shipping

OpenAIRE

Mæstad, Ottar; Evensen, Annika Jaersen; Mathiesen, Lars; Olsen, Kristian

2000-01-01

This report summarises the main results from the project Norwegian and international climate policy consequences for shipping. The aim of the project has been to shed light on how climate policies might affect shipping, both from the cost side and from the demand side. The project has been divided into three sub-projects, investigating the consequences of climate policies for 1. Optimal shipping operations and management 2. The competitiveness of shipping relative to land transport 3. The tra...

Microelectronic packaging

CERN Document Server

Datta, M; Schultze, J Walter

2004-01-01

Microelectronic Packaging analyzes the massive impact of electrochemical technologies on various levels of microelectronic packaging. Traditionally, interconnections within a chip were considered outside the realm of packaging technologies, but this book emphasizes the importance of chip wiring as a key aspect of microelectronic packaging, and focuses on electrochemical processing as an enabler of advanced chip metallization.Divided into five parts, the book begins by outlining the basics of electrochemical processing, defining the microelectronic packaging hierarchy, and emphasizing the impac

Performance Monitoring of Ships

DEFF Research Database (Denmark)

Hansen, Søren Vinther

is used as input to the system and by comparing model and ship behaviour, an index describing the ship’s performance is generated. The work in this thesis is based on data logged through the automation system on board a PostPanmax container ship where data have been logged through a year. A routine...... in the models have been identified. The models used in this work are based on empirical relations or based on regression analyses of model tests and full-scale trials. In order to achieve valid results the conditions where performance is estimated have to be inside the boundaries of the model. Filters have been......The purpose of the research project is to establish a reliable index in the performance evaluation of ships. During operation the ship will experience added resistance due to fouling of hull and propeller. The added resistance will lead to increased fuel consumption and thus increased emissions...

Computational methods for more fuel-efficient ship

NARCIS (Netherlands)

Koren, B.

2008-01-01

The flow of water around a ship powered by a combustion engine is a key factor in the ship's fuel consumption. The simulation of flow patterns around ship hulls is therefore an important aspect of ship design. While lengthy computations are required for such simulations, research by Jeroen Wackers

48 CFR 1371.118 - Changes-ship repair.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Changes-ship repair. 1371.118 Section 1371.118 Federal Acquisition Regulations System DEPARTMENT OF COMMERCE DEPARTMENT SUPPLEMENTAL REGULATIONS ACQUISITIONS INVOLVING SHIP CONSTRUCTION AND SHIP REPAIR Provisions and Clauses 1371.118 Changes—ship repair. Insert clause...

Some concepts of future nuclear ship

International Nuclear Information System (INIS)

Fujino, Masataka

2000-01-01

Characteristic features of nuclear power generation are as follows: (1) Thermal energy can be continuously extracted for a long time without fuel feed, (2) Nuclear energy is suitable for generating huge power, (3) Oxygen is unnecessary for combustion of fuel, and (4) Unlike fossil fuel, nuclear power generation does not exhaust NOx, SOx, and CO 2 : it can be considered environmentally friendly. In view of these features, the Japan Atomic Energy Research Institute commissioned the Shipbuilding Research Association of Japan (JSRA) to survey what kinds of nuclear ship would be put to practical use in the near future. For this purpose, a research committee was organized in 1992 by the JSRA, and concluded its investigation in 1996. The main aim of this research was to clarify the requirements of ship performance as nuclear ships, and then to extract the technical issues of the marine reactor installed in nuclear ships to be solved. As a result of the survey, it was suggested that displacement-type large high-speed container ship would be one of the promising future nuclear merchant ships, and 6500 m deep-sea and 600 m undersea scientific research submersibles would be other promising nuclear special purpose ships. At the same time, various requirements of marine reactors, which are expected to be installed in these ships, were clarified mainly from the technical viewpoints. (author)

Total Analysis System for Ship Structural Strength

OpenAIRE

Takuya, Yoneya; Hiroyuki, Kobayashi; Abdul M., Rahim; Yoshimichi, Sasaki; Masaki, Irisawa; Technical Investigation and Information Department, Research Center; Technical Investigation and Information Department, Research Center; Singapore Office; Technical Investigation and Information Department, Research Center; Technical Investigation and Information Department, Research Center

2001-01-01

This paper outlines a total analysis system for ship hull structures, which integrates a wide variety of analysis functions to realise practical applications of rational methods for assessing ship structural strength. It is based on direct calculation of wave-induced loads as well as three-dimensional structural analysis of an entire-ship or hold structure. Three major analysis functions of the total system are ship motion and wave load analysis, ship structural analysis and statistical analy...

The Transformation of Swedish Shipping, 1970-2010

OpenAIRE

Sjögren, Hans; Taro Lennerfors, Thomas; Taudal Poulsen, Rene

2012-01-01

Since the early 1970s, as shipping has undergone a period of structural change, Swedish shipping has rapidly declined from a position of global importance. The Swedish-controlled fleet has dwindled, and the structure of the industry itself has changed. This article explores the influence of shipping markets, shipping regulations, company strategies, maritime know-how, and financial resources on the development of Swedish shipping from 1970 to 2010. A comparison is made between, on the one han...

Safety analysis report: packages. Pu oxide and Am oxide shipping cask (Packaging of fissile and other radioactive materials). Final report

International Nuclear Information System (INIS)

Chalfant, G.G.

1980-05-01

The PuO 2 cask or SP 5320-2 and 3 cask is designed for surface shipment of americium or plutonium. The cask design was physically tested to demonstrate that it met the criteria specified in US ERDA Manual Chapter 0529, and Chapter I, Interstate Commerce Commission. The package has been assessed for transport of up to 357 grams of plutonium (403 grams PuO 2 powder) and up to 176 grams of americium (200 grams AmO 2 powder), having a maximum decay heat of 203 watts. Criticality evaluation alone would allow the shipment as Fissile Class II but the radiation level of the cask, measured at the time of shipment, may exceed 50 mrem/h at the surface and require shipment as Fissile Class III. Sample calculations address only the more restrictive of the two materials, which in most cases is 238 PuO 2

Effective and Safe Ships

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup; Amdahl, Jørgen; Rutgersson, Olle

1996-01-01

A Joint Nordic Research project "Effecive and Safe Ships" is presented. The project is aiming to develop methods and tools for quantitative evaluation fo ship safety. This report is the report of the preliminary phase where the plan for the main project is developed. The objectives of the project...

The Packaging Handbook -- A guide to package design

International Nuclear Information System (INIS)

Shappert, L.B.

1995-01-01

The Packaging Handbook is a compilation of 14 technical chapters and five appendices that address the life cycle of a packaging which is intended to transport radioactive material by any transport mode in normal commerce. Although many topics are discussed in depth, this document focuses on the design aspects of a packaging. The Handbook, which is being prepared under the direction of the US Department of Energy, is intended to provide a wealth of technical guidance that will give designers a better understanding of the regulatory approval process, preferences of regulators in specific aspects of packaging design, and the types of analyses that should be seriously considered when developing the packaging design. Even though the Handbook is concerned with all packagings, most of the emphasis is placed on large packagings that are capable of transporting large radioactive sources that are also fissile (e.g., spent fuel). These are the types of packagings that must address the widest range of technical topics in order to meet domestic and international regulations. Most of the chapters in the Handbook have been drafted and submitted to the Oak Ridge National Laboratory for editing; the majority of these have been edited. This report summarizes the contents

Analysis of ship life cycles: the impact of economic cycles and ship inspection

NARCIS (Netherlands)

Bijwaard, G.E.; Knapp, S.

2009-01-01

Due to the shipping industry's international legal framework, there are loopholes in the system, which can increase the risk of incidents with high economic costs due to the substandard operation of vessels. This article uses duration analysis and through the creation of ship life cycles provides

Simple analytical relations for ship bow waves

Science.gov (United States)

Noblesse, Francis; Delhommeau, G.?Rard; Guilbaud, Michel; Hendrix, Dane; Yang, Chi

Simple analytical relations for the bow wave generated by a ship in steady motion are given. Specifically, simple expressions that define the height of a ship bow wave, the distance between the ship stem and the crest of the bow wave, the rise of water at the stem, and the bow wave profile, explicitly and without calculations, in terms of the ship speed, draught, and waterline entrance angle, are given. Another result is a simple criterion that predicts, also directly and without calculations, when a ship in steady motion cannot generate a steady bow wave. This unsteady-flow criterion predicts that a ship with a sufficiently fine waterline, specifically with waterline entrance angle 2, may generate a steady bow wave at any speed. However, a ship with a fuller waterline (25E) can only generate a steady bow wave if the ship speed is higher than a critical speed, defined in terms of αE by a simple relation. No alternative criterion for predicting when a ship in steady motion does not generate a steady bow wave appears to exist. A simple expression for the height of an unsteady ship bow wave is also given. In spite of their remarkable simplicity, the relations for ship bow waves obtained in the study (using only rudimentary physical and mathematical considerations) are consistent with experimental measurements for a number of hull forms having non-bulbous wedge-shaped bows with small flare angle, and with the authors' measurements and observations for a rectangular flat plate towed at a yaw angle.

46 CFR 173.051 - Public nautical school ships.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Public nautical school ships. 173.051 Section 173.051 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO VESSEL USE School Ships § 173.051 Public nautical school ships. Each public nautical school...

''We crash, burn, and crush'': A history of packaging at Sandia National Laboratories, 1978 -1997

International Nuclear Information System (INIS)

Mora, C.J.; McConnell, P.

1997-11-01

Even prior to the beginning of the nuclear age, the packaging and transportation of nuclear materials was a prime national concern. Nuclear materials such as uranium and plutonium had to be transported safely (and secretly) to the Manhattan Engineer District Laboratory in Los Alamos, New Mexico. The subsequent post war use of nuclear power for the generation of electricity and accelerated weapons development programs resulted in radioactive waste byproducts, such as spent fuel and plutonium, that were stored on site at utilities and federal weapons sites. While projected repositories for long term storage of radioactive waste are being planned, both low and high level radioactive materials on occasion must be moved safely. Movement to interim storage and, for low level waste, repository sites, is accomplished by a combination of truck, rail, ship, and air. The US Department of Energy (DOE) directs transportation activities including cask development technology for use in single or multimodal (a combination of land, water, and air) transport. In 1978, Sandia National Laboratories was selected as the lead contractor for basic transportation technology. This report is divided into the following topics: (1) early research and development (1936--1978); (2) radioactive material package test (1975--1977); (3) the SNL Transportation Technology Center; (4) TRUPACT-II; (5) beneficial uses of shipping system casks; (6) C-141B drop tests; (7) MIDAS; (8) MOSAIK; (9) SEARAM; (10) PATRAM; and (11) a chronology of transportation activities

Ship emissions and air pollution in Denmark

DEFF Research Database (Denmark)

Olesen, Helge Rørdam; Winther, Morten; Ellermann, Thomas

A project has been carried out to map the contribution from ship traffic to air pollution in Denmark. A main element in the project is the establishment of a new, improved inventory of ship emissions for the waters around Denmark. The inventory makes use of the so-called AIS system, which...... continuously keeps track of ship positions. The inventory provides basis for model calculations of air quality in Denmark for the years 2007, 2011 and 2020. The study has focus on identifying the contribution from ships, and on assessing the effect of international regulations of ship pollution. A minor...... component of the study concerns the contribution to local air pollution from ships at port....

Uranium hexafluoride packaging tiedown systems overview at Portsmouth Gaseous Diffusion Plant, Piketon, Ohio

International Nuclear Information System (INIS)

Becker, D.L.; Green, D.J.; Lindquist, M.R.

1993-07-01

The Portsmouth Gaseous Diffusion Plant (PORTS) in Piketon, Ohio, is operated by Martin Marietta Energy Systems, Inc., through the US Department of Energy-Oak Ridge Operations Office (DOE-ORO) for the US Department of Energy-Headquarters, Office of Nuclear Energy. The PORTS conducts those operations that are necessary for the production, packaging, and shipment of uranium hexafluoride (UF 6 ). Uranium hexafluoride enriched uranium than 1.0 wt percent 235 U shall be packaged in accordance with the US Department of Transportation (DOT) regulations of Title 49 CFR Parts 173 (Reference 1) and 178 (Reference 2), or in US Nuclear Regulatory Commission (NRC) or US Department of Energy (DOE) certified package designs. Concerns have been expressed regarding the various tiedown methods and condition of the trailers being used by some shippers/carriers for international transport of the UF 6 cylinders/overpacks. Because of the concerns about international shipments, the US Department of Energy-Headquarters (DOE-HQ) Office of Nuclear Energy, through DOE-HQ Transportation Management Division, requested Westinghouse Hanford Company (Westinghouse Hanford) to review UF 6 packaging tiedown and shipping practices used by PORTS, and where possible and appropriate, provide recommendations for enhancing these practices. Consequently, a team of two individuals from Westinghouse Hanford visited PORTS on March 5 and 6, 1990, for the purpose of conducting this review. The paper provides a brief discussion of the review activities and a summary of the resulting findings and recommendations. A detailed reporting of the is documented in Reference 4

Influences of the separation distance, ship speed and channel dimension on ship maneuverability in a confined waterway

Science.gov (United States)

Du, Peng; Ouahsine, Abdellatif; Sergent, Philippe

2018-05-01

Ship maneuvering in the confined inland waterway is investigated using the system-based method, where a nonlinear transient hydrodynamic model is adopted and confinement models are implemented to account for the influence of the channel bank and bottom. The maneuvering model is validated using the turning circle test, and the confinement model is validated using the experimental data. The separation distance, ship speed, and channel width are then varied to investigate their influences on ship maneuverability. With smaller separation distances and higher speeds near the bank, the ship's trajectory deviates more from the original course and the bow is repelled with a larger yaw angle, which increase the difficulty of maneuvering. Smaller channel widths induce higher advancing resistances on the ship. The minimum distance to the bank are extracted and studied. It is suggested to navigate the ship in the middle of the channel and with a reasonable speed in the restricted waterway.

27 CFR 44.187 - Shipping containers.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Shipping containers. 44... Shipping containers. Each shipping case, crate, or other container in which tobacco products, or cigarette... same containers in which they were received from the factory. (72 Stat. 1418, as amended; 26 U.S.C...

27 CFR 44.254 - Shipping containers.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Shipping containers. 44.254 Section 44.254 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU... Requirements § 44.254 Shipping containers. Each shipping case, crate, or other container, in which cigars are...

49 CFR 176.24 - Shipping papers.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Shipping papers. 176.24 Section 176.24... Requirements § 176.24 Shipping papers. (a) A person may not accept a hazardous material for transportation or transport a hazardous material by vessel unless that person has received a shipping paper prepared in...

49 CFR 177.817 - Shipping papers.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Shipping papers. 177.817 Section 177.817... Information and Regulations § 177.817 Shipping papers. (a) General requirements. A person may not accept a... received a shipping paper prepared in accordance with part 172 of this subchapter or the material is...

49 CFR 174.24 - Shipping papers.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Shipping papers. 174.24 Section 174.24... Requirements § 174.24 Shipping papers. (a) A person may not accept a hazardous material for transportation or transport a hazardous material by rail unless that person receives a shipping paper prepared in accordance...

Development of nuclear powered ship in Japan

International Nuclear Information System (INIS)

Sato, Hiroshi

1976-01-01

The development of nuclear merchant ship in Japan was started in 1955 by the establishment of Nuclear Ship Study Group, and since then, the investigation, test and research on nuclear ships have been continued. As a result, a nuclear ocean observation and supply ship was designed for trial. Researches were carried out also in JAERI and Institute for Technical Research of Ships. Meanwhile, the nuclear icebreaker Lenin was completed in Soviet Union in 1959, the nuclear ship Savannah set out for maiden voyage in U.S. in 1962, and the construction of the nuclear ore carrier Otto Hahn was prepared in FRG. Japan Nuclear Ship Development Corp. was established in 1963, and started the design and construction of the first nuclear ship in Japan, Mutsu. The basic policy in the construction is the improvement of nuclear ship technology, the securing of safety, and the use of domestic technologies as far as possible. The progress of the design, construction and test of the Mutsu is described. Owing to the problem of radiation leak, the development of nuclear ships stagnated for a while, but the nuclear plant of the Mutsu demonstrated the expected performance in the functional test, land criticality test and zero output test, and it is expected that the bud of the independent development brought up so far can bear valuable fruit. The independent development of marine nuclear reactors should be continued by selecting the way most suitable to Japan. (Kako, I.)

Ship emissions and their externalities for Greece

Science.gov (United States)

Tzannatos, Ernestos

2010-06-01

The existing and emerging international and European policy framework for the reduction of ship exhaust emissions dictates the need to produce reliable national, regional and global inventories in order to monitor emission trends and consequently provide the necessary support for future policy making. Furthermore, the inventories of ship exhaust emissions constitute the basis upon which their external costs are estimated in an attempt to highlight the economic burden they impose upon the society and facilitate the cost-benefit analysis of the proposed emission abatement technologies, operational measures and market-based instruments prior to their implementation. The case of Greece is of particular interest mainly because the dense ship traffic within the Greek seas directly imposes the impact of its exhaust emission pollutants (NO x, SO 2 and PM) upon the highly populated, physically sensitive and culturally precious Greek coastline, as well as upon the land and seas of Greece in general, whereas the contribution of Greece in the global CO 2 inventory at a time of climatic change awareness cannot be ignored. In this context, this paper presents the contribution of Greece in ship exhaust emissions of CO 2, NO x, SO 2 and PM from domestic and international shipping over the last 25 years (1984-2008), utilizing the fuel-based (fuel sales) emission methodology. Furthermore, the ship exhaust emissions generated within the Greek seas and their externalities are estimated for the year 2008, through utilizing the fuel-based (fuel sales) approach for domestic shipping and the activity-based (ship traffic) approach for international shipping. On this basis, it was found that during the 1984 to 2008 period the fuel-based (fuel sales) ship emission inventory for Greece increased at an average annual rate of 2.85%. In 2008, the CO 2, NO x, SO 2 and PM emissions reached 12.9 million tons (of which 12.4 million tons of CO 2) and their externalities were found to be around 3

Report of Nuclear Powered Ship Meeting

International Nuclear Information System (INIS)

1984-01-01

The development of nuclear-powered ships in Japan broke down due to the radiation leak on the nuclear ship ''Mutsu'' in 1974, and the objective has not yet been attained. The Japan Nuclear Ship Research and Development Agency was reorganized to advance the development of nuclear-powered ships and to develop marine nuclear reactors. Recently, various opinions have been expressed regarding the development of nuclear-powered ships and Mutsu, accordingly, it is necessary to clarify the way it should be. The Atomic Energy Commission organized this meeting to discuss the problem. The practical use of nuclear-powered ships is expected at the beginning of the 21st century, but it is only the guess. But it is important to accumulate the technology, knowledge and experience to prepare for the use of nuclear-powered ships. The continuation of the development of Mutsu is important for the future, and the construction of the new home port is unavoidable. The aim of the research and development, and the concrete way of advancing the research and development of Mutsu are discussed. It is scheduled that the Agency is integrated with other atomic energy organizations by March, 1985. The consideration to be given for implementing the integration is described. (Kako, I.)

19 CFR 4.69 - Shipping articles.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Shipping articles. 4.69 Section 4.69 Customs... VESSELS IN FOREIGN AND DOMESTIC TRADES Foreign Clearances § 4.69 Shipping articles. No vessel of the U.S... officer, of the shipping articles agreements, including any seaman's allotment agreement, required by 46 U...

29 CFR 1915.162 - Ship's boilers.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Ship's boilers. 1915.162 Section 1915.162 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Ship's Machinery and Piping Systems § 1915.162 Ship's boilers. (a) Before...

Added masses of ship structures

CERN Document Server

Korotkin, Alexandr I

2008-01-01

This essentially self-contained reference book contains data on added masses of ships and various ship and marine engineering structures. Theoretical and experimental methods for determining added masses of these objects are described.

Control mechanisms for Nordic ship emissions

Energy Technology Data Exchange (ETDEWEB)

Martinsen, K. [DNV, Oslo (Norway); Torvanger, A. [Cicero, Oslo (Norway)

2013-04-15

Shipping today operates under a complex set of international and domestic regulations. However, the environmental regulations have lagged behind those of other industries. This situation is now changing quite dramatically. The increased focus on environmental issues, combined with the growing realisation of the actual pollution burden imposed by shipping, has led to an upsurge in both international and national regulations. Some are ready and will enter into force in the near future, while others are still being developed. On behalf of the Nordic Council of Ministers DNV has carried out a study on possible control mechanisms for Nordic ship emission. The aim is to assess the baseline shipping emissions and reduction potential and the possible controlling mechanisms (both incentives and regulations) available for reducing the emissions to air from shipping within the Nordic region. (Author)

Spent fuel shipping cask sealing concepts

International Nuclear Information System (INIS)

Sonnier, C.S.

1989-05-01

In late 1985, the International Atomic Energy Agency (IAEA) requested the US Program for Technical Assistance to IAEA Safeguards (POTAS) to provide a study which examined sealing concepts for application to spent fuel shipping casks. This request was approved, and assigned to Sandia National Laboratories (Sandia). In the course of this study, discussions were held with personnel in the International Safeguards Community who were familiar with the shipping casks used in their States. A number of shipping casks were examined, and discussions were held with two shipping cask manufacturers in the US. As a result of these efforts, it was concluded that the shipping casks provided an extremely good containment, and that many of the existing casks can be effectively sealed by applying the seal to the cask closure bolts/nuts

Development of a nuclear ship safety philosophy

International Nuclear Information System (INIS)

Thompson, T.E.

1978-01-01

A unique safety philosophy must be recognized and accepted as an integral part of the design and operation of a nuclear ship. For the nuclear powered ship, the ultimate safety of the reactor and therefore the crew and the environment lies with the safety of the ship itself. The basis for ship safety is its ability to navigate and survive the conditions or the environment in which it may find itself. The subject of traditional ship safety is examined along with its implication for reactor protection and safety. Concepts of reactor safety are also examined. These two philosophies are combined in a manner so as to provide a sound philosophy for the safety of nuclear ships, their crews, and the environment

15 CFR 750.11 - Shipping tolerances.

Science.gov (United States)

2010-01-01

... in the ECCN applicable to your item reads “ $ value” or “in $ value”, there is no shipping tolerance... is no shipping tolerance with respect to the number of units. However, the value of all of your... shipping tolerance on this license because the items are controlled by an ECCN where “$ value” is the...

Ship design methodologies of preliminary design

CERN Document Server

Papanikolaou, Apostolos

2014-01-01

This book deals with ship design and in particular with methodologies of the preliminary design of ships. The book is complemented by a basic bibliography and five appendices with useful updated charts for the selection of the main dimensions and other basic characteristics of different types of ships (Appendix A), the determination of hull form  from the data of systematic hull form series (Appendix B), the detailed description of the relational method for the preliminary estimation of ship weights (Appendix C), a brief review of the historical evolution of shipbuilding science and technology from the prehistoric era to date (Appendix D) and finally a historical review of regulatory developments of ship's damage stability to date (Appendix E).  The book can be used as textbook for ship design courses or as additional reading for university or college students of naval architecture courses and related disciplines; it may also serve as a reference book for naval architects, practicing engineers of rel...