WorldWideScience

Sample records for ship model testing

  1. Test Ship

    Federal Laboratory Consortium — The U. S. Navy dedicated the decommissioned Spruance Class destroyer ex-PAUL F. FOSTER (EDD 964), Test Ship, primarily for at sea demonstration of short range weapon...

  2. Uncertainty Analysis of Resistance Tests in Ata Nutku Ship Model Testing Laboratory of Istanbul Technical University

    Cihad DELEN

    2015-12-01

    Full Text Available In this study, some systematical resistance tests, where were performed in Ata Nutku Ship Model Testing Laboratory of Istanbul Technical University (ITU, have been included in order to determine the uncertainties. Experiments which are conducted in the framework of mathematical and physical rules for the solution of engineering problems, measurements, calculations include uncertainty. To question the reliability of the obtained values, the existing uncertainties should be expressed as quantities. The uncertainty of a measurement system is not known if the results do not carry a universal value. On the other hand, resistance is one of the most important parameters that should be considered in the process of ship design. Ship resistance during the design phase of a ship cannot be determined precisely and reliably due to the uncertainty resources in determining the resistance value that are taken into account. This case may cause negative effects to provide the required specifications in the latter design steps. The uncertainty arising from the resistance test has been estimated and compared for a displacement type ship and high speed marine vehicles according to ITTC 2002 and ITTC 2014 regulations which are related to the uncertainty analysis methods. Also, the advantages and disadvantages of both ITTC uncertainty analysis methods have been discussed.

  3. Using an Autonomous Scale Ship Model for Resistance and Parametric Roll Tests

    Fernando LOPEZ PEŇA

    2015-04-01

    Full Text Available This work presents the developing of a self-propelled scale ship model aimed to perform resistance and parametric roll tests in towing tanks. The main characteristic of the proposed system is that it doesn’t have any material link to a towing device to carry out the tests. This ship model has been fully instrumented in order to acquire all the significant raw data, process them onboard and communicate with an inshore station. This works presents a description of the proposed model as well as some results obtained by its use during a towing tank testing campaign.

  4. Extrapolation of model tests measurements of whipping to identify the dimensioning sea states for container ships

    Storhaug, Gaute; Andersen, Ingrid Marie Vincent

    2015-01-01

    to small storms. Model tests of three container ships have been carried out in different sea states under realistic assumptions. Preliminary extrapolation of the measured data suggested that moderate storms are dimensioning when whipping is included due to higher maximum speed in moderate storms...

  5. Effects of drop testing on scale model shipping containers shielded with depleted uranium

    Butler, T.A.

    1980-02-01

    Three scale model shipping containers shielded with depleted uranium were dropped onto an essentially unyielding surface from various heights to determine their margins to failure. This report presents the results of a thorough posttest examination of the models to check for basic structural integrity, shielding integrity, and deformations. Because of unexpected behavior exhibited by the depleted uranium shielding, several tests were performed to further characterize its mechanical properties. Based on results of the investigations, recommendations are made for improved container design and for applying the results to full-scale containers. Even though the specimens incorporated specific design features, the results of this study are generally applicable to any container design using depleted uranium

  6. Friction correction for model ship resistance and propulsion tests in ice at NRC's OCRE-RC

    Michael Lau

    2018-05-01

    Full Text Available This paper documents the result of a preliminary analysis on the influence of hull-ice friction coefficient on model resistance and power predictions and their correlation to full-scale measurements. The study is based on previous model-scale/full-scale correlations performed on the National Research Council - Ocean, Coastal, and River Engineering Research Center's (NRC/OCRE-RC model test data. There are two objectives for the current study: (1 to validate NRC/OCRE-RC's modeling standards in regarding to its practice of specifying a CFC (Correlation Friction Coefficient of 0.05 for all its ship models; and (2 to develop a correction methodology for its resistance and propulsion predictions when the model is prepared with an ice friction coefficient slightly deviated from the CFC of 0.05. The mean CFC of 0.056 and 0.050 for perfect correlation as computed from the resistance and power analysis, respectively, have justified NRC/OCRE-RC's selection of 0.05 for the CFC of all its models. Furthermore, a procedure for minor friction corrections is developed. Keywords: Model test, Ice resistance, Power, Friction correction, Correlation friction coefficient

  7. A Novel Approach to Turbulence Stimulation for Ship-Model Testing

    2010-05-11

    a given hull form. As van Manen and van Oossanen note, ship resistance is related to “the proportions and shape… of the hull, the size and type of...propulsion plant to provide motive power, and the device or system to transform the power into effective thrust” ( van Manen and van Oossanen, 1988...what is known as the Ship-Model Tester’s Dilemma, which van Manen and van Oossanen define as “the conditions of mechanical similitude for both friction

  8. Helicopter-Ship Qualification Testing

    Hoencamp, A.

    2015-01-01

    The goal of this research project is to develop a novel test methodology which can be used for optimizing cost and time efficiency of helicopter-ship qualification testing without reducing safety. For this purpose, the so-called “SHOL-X” test methodology has been established, which includes the

  9. Analysis, scale modeling, and full-scale test of a railcar and spent-nuclear-fuel shipping cask in a high-velocity impact against a rigid barrier

    Huerta, M.

    1981-06-01

    This report describes the mathematical analysis, the physical scale modeling, and a full-scale crash test of a railcar spent-nuclear-fuel shipping system. The mathematical analysis utilized a lumped-parameter model to predict the structural response of the railcar and the shipping cask. The physical scale modeling analysis consisted of two crash tests that used 1/8-scale models to assess railcar and shipping cask damage. The full-scale crash test, conducted with retired railcar equipment, was carefully monitored with onboard instrumentation and high-speed photography. Results of the mathematical and scale modeling analyses are compared with the full-scale test. 29 figures

  10. A Nonlinear Ship Manoeuvering Model: Identification and adaptive control with experiments for a model ship

    Roger Skjetne

    2004-01-01

    Full Text Available Complete nonlinear dynamic manoeuvering models of ships, with numerical values, are hard to find in the literature. This paper presents a modeling, identification, and control design where the objective is to manoeuver a ship along desired paths at different velocities. Material from a variety of references have been used to describe the ship model, its difficulties, limitations, and possible simplifications for the purpose of automatic control design. The numerical values of the parameters in the model is identified in towing tests and adaptive manoeuvering experiments for a small ship in a marine control laboratory.

  11. Ship Repair Workflow Cost Model

    McDevitt, Mike

    2003-01-01

    The effects of intermittent work patterns and funding on the costs of ship repair and maintenance were modeled for the San Diego region in 2002 for Supervisor of Shipbuilding and Repair (SUPSHIP) San Diego...

  12. Crash testing of nuclear fuel shipping containers

    Jefferson, R.M.; Yoshimura, H.R.

    1977-08-01

    In an attempt to understand the dynamics of extra severe transportation accidents and to evaluate state-of-the-art computational techniques for predicting the dynamic response of shipping casks involved in vehicular system crashes, the Environmental Control Technology Division of ERDA undertook a program with Sandia to investigate these areas. The program encompasses the following distinct major efforts. The first of these utilizes computational methods for predicting the effects of the accident environment and, subsequently, to calculate the damage incurred by a container as the result of such an accident. The second phase involves the testing of 1 / 8 -scale models of transportation systems. Through the use of instrumentation and high-speed motion photography the accident environments and physical damage mechanisms are studied in detail. After correlating the results of these first two phases, a full scale event involving representative hardware is conducted. To date two of the three selected test scenarios have been completed. Results of the program to this point indicate that both computational techniques and scale modeling are viable engineering approaches to studying accident environments and physical damage to shipping casks

  13. Crash testing of nuclear fuel shipping containers

    Jefferson, R.M.; Yoshimura, H.R.

    1977-12-01

    In an attempt to understand the dynamics of extra severe transportation accidents and to evaluate state-of-the-art computational techniques for predicting the dynamic response of shipping casks involved in vehicular system crashes, the Environmental Control Technology Division of ERDA undertook a program with Sandia to investigate these areas. This program, which began in 1975, encompasses the following distinct major efforts. The first of these utilizes computational methods for predicting the effects of the accident environment and, subsequently, to calculate the damage incurred by a container as the result of such an accident. The second phase involves the testing of 1 / 8 -scale models of transportation systems. Through the use of instrumentation and high-speed motion photography, the accident environments and physical damage mechanisms are studied in detail. After correlating the results of these first two phases, a full scale event involving representative hardware is conducted. To date two of the three selected test scenarios have been completed. Results of the program to this point indicate that both computational techniques and scale modeling are viable engineering approaches to studying accident environments and physical damage to shipping casks

  14. Ship Systems Survivability Test Site

    Federal Laboratory Consortium — Area for testing survivability of shipboard systems to include electrical, communications, and fire suppression. Multipurpose test range for supporting gun firing,...

  15. Ship Model Testing

    2016-01-15

    vear. (a) (b) Figure 12: (a): ProJet 350 HD Max. (b): Eight inch 3D printed propeller. Purchases for this project total SI 10.719 CFD Workstations...AVAILABILITY STATEMENT 13. SUPPLEMENTARY NOTES 14. ABSTRACT This proposal identifies numerous projects that have improved the research and educational ...filtered electric power, and structural analysis equipment. The projects covered by this grant enable Webb to conduct research and educational

  16. Crash testing of spent-nuclear-fuel shipping systems

    Yoshimura, H.R.

    1978-01-01

    Full scale testing to date has verified that current analytical tools and the use of scale model testing are both accurate methods for predicting shipping cask response to severe accident conditions. The containers tested are capable of surviving severe transportation accidents

  17. Mathematical Ship Modeling for Control Applications

    Perez, Tristan; Blanke, Mogens

    2002-01-01

    In this report, we review the models for describing the motion of a ship in four degrees of freedom suitable for control applications. We present the hydrodynamic models of two ships: a container and a multi-role naval vessel. The models are based on experimental results in the four degrees...

  18. Model for Estimation of Fuel Consumption of Cruise Ships

    Morten Simonsen

    2018-04-01

    Full Text Available This article presents a model to estimate the energy use and fuel consumption of cruise ships that sail Norwegian waters. Automatic identification system (AIS data and technical information about cruise ships provided input to the model, including service speed, total power, and number of engines. The model was tested against real-world data obtained from a small cruise vessel and both a medium and large cruise ship. It is sensitive to speed and the corresponding engine load profile of the ship. A crucial determinate for total fuel consumption is also associated with hotel functions, which can make a large contribution to the overall energy use of cruise ships. Real-world data fits the model best when ship speed is 70–75% of service speed. With decreased or increased speed, the model tends to diverge from real-world observations. The model gives a proxy for calculation of fuel consumption associated with cruise ships that sail to Norwegian waters and can be used to estimate greenhouse gas emissions and to evaluate energy reduction strategies for cruise ships.

  19. Modeling of Ship Propulsion Performance

    Pedersen, Benjamin Pjedsted; Larsen, Jan

    2009-01-01

    Full scale measurements of the propulsion power, ship speed, wind speed and direction, sea and air temperature, from four different loading conditions has been used to train a neural network for prediction of propulsion power. The network was able to predict the propulsion power with accuracy...

  20. Standard Ship Test and Inspection Plan, Procedures and Database

    1999-01-01

    ... construction schedules and increased cost is the area of test and inspection. This project investigates existing rules and regulations for testing and inspection of commercial ships and identifies differences and similarities within the requirements. The results include comparison matrices, a standard test plan, a set of standard test procedures, and a sample test database developed for a typical commercial ship.

  1. Full-scale tests of spent-nuclear-fuel shipping systems

    Yoshimura, H.R.; Huerta, M.

    1976-01-01

    Sandia Laboratories will be conducting, for the U.S. Energy Research and Development Administration, a series of tests involving spent-nuclear-fuel shipping systems. Large shipping casks in the 20500 to 70000-kg range will be included in the following full-scale tests: (1) Runaway tractor-trailer crash into a solid concrete barrier while carrying a shipping cask. (2) High-speed locomotive grade-crossing impact with a truck carrying a shipping cask. (3) High-speed derailment, collision, and fire involving a special railcar and shipping cask. The hardware and testing procedures for each of the tests are described. The analysis conducted in advance of the tests addresses the modelling technique used and a description of the scale-model tests. Analytical modelling being done before running the full-scale tests is also described. (author)

  2. Structural assurance testing for post-shipping satellite inspection

    Reynolds, Whitney D.; Doyle, Derek; Arritt, Brandon

    2012-04-01

    Current satellite transportation sensors can provide a binary indication of the acceleration or shock that a satellite has experienced during the shipping process but do little to identify if significant structural change has occurred in the satellite and where it may be located. When a sensor indicates that the satellite has experienced shock during transit, an extensive testing process begins to evaluate the satellite functionality. If errors occur during the functional checkout, extensive physical inspection of the structure follows. In this work an alternate method for inspecting satellites for structural defects after shipping is presented. Electro- Mechanical Impedance measurements are used as an indication of the structural state. In partnership with the Air Force Research Laboratory University Nanosatellite Program, Cornell's CUSat mass model was instrumented with piezoelectric transducers and tested under several structural damage scenarios. A method for detecting and locating changes in the structure using EMI data is presented.

  3. Network Design Models for Container Shipping

    Reinhardt, Line Blander; Kallehauge, Brian; Nielsen, Anders Nørrelund

    This paper presents a study of the network design problem in container shipping. The paper combines the network design and fleet assignment problem into a mixed integer linear programming model minimizing the overall cost. The major contributions of this paper is that the time of a vessel route...... is included in the calculation of the capacity and that a inhomogeneous fleet is modeled. The model also includes the cost of transshipment which is one of the major cost for the shipping companies. The concept of pseudo simple routes is introduced to expand the set of feasible routes. The linearization...

  4. Statistical modelling for ship propulsion efficiency

    Petersen, Jóan Petur; Jacobsen, Daniel J.; Winther, Ole

    2012-01-01

    This paper presents a state-of-the-art systems approach to statistical modelling of fuel efficiency in ship propulsion, and also a novel and publicly available data set of high quality sensory data. Two statistical model approaches are investigated and compared: artificial neural networks...

  5. Confirmation tests of PWR surveillance capsule shipping container

    Tomita, N.; Ue, K.; Ohashi, M.; Asada, K.; Yoneda, Y.

    1980-01-01

    Mitsubishi Heavy Industries, Ltd. carried out the confirmation tests to confirm the reliability of the PWR surveillance capsule shipping container and to collect cask design data using a 10-ton weight full scale model at Kobe Shipyard and Engine Works. This report presents the outline of these tests. The B Type container was a cylinder 3289 mm long, 1080 mm in diameter and designed in accordance with the new modified Japanese regulations similar to IAEA regulation. These tests consist of four 9 m drop tests, two 1 m puncture tests, a fire test and an immersion test. In conclusion, safetyness of this container has been proved and various technical data for cask design were also collected through these tests. (author)

  6. EX1101: Ship Shakedown and Patch Tests on NOAA Ship Okeanos Explorer (EM302)

    National Oceanic and Atmospheric Administration, Department of Commerce — This project will involve the shakedown of all Okeanos Explorer ship capabilities and a patch test of the Kongsberg EM302 multibeam system. Operations for this...

  7. PARTICIPATION BASED MODEL OF SHIP CREW MANAGEMENT

    Toni Bielić

    2014-10-01

    Full Text Available 800x600 This paper analyse the participation - based model on board the ship as possibly optimal leadership model existing in the shipping industry with accent on decision - making process. In the paper authors have tried to define master’s behaviour model and management style identifying drawbacks and disadvantages of vertical, pyramidal organization with master on the top. Paper describes efficiency of decision making within team organization and optimization of a ship’s organisation by introducing teamwork on board the ship. Three examples of the ship’s accidents are studied and evaluated through “Leader - participation” model. The model of participation based management as a model of the teamwork has been applied in studying the cause - and - effect of accidents with the critical review of the communication and managing the human resources on a ship. The results have showed that the cause of all three accidents is the autocratic behaviour of the leaders and lack of communication within teams. Normal 0 21 false false false HR X-NONE X-NONE MicrosoftInternetExplorer4

  8. Shipping

    Wijnolst, N.; Wergeland, T.

    1996-01-01

    Shipping is a multi-faceted industry which is rather complex to define from an academic point of view. This book attempts to grasp these complexities and provide the reader with an overview of the main topics and terminology in shipping. The book is based on material from our courses in shipping at

  9. Ship plume modeling in EOSTAR

    Iersel, M. van; Mack, A.; Degach, M.A.C.; Eijk, A.M.J. van

    2014-01-01

    The EOSTAR model aims at assessing the performance of electro-optical (EO) sensors deployed in a maritime surface scenario, by providing operational performance measures (such as detection ranges) and synthetic images. The target library of EOSTAR includes larger surface vessels, for which the

  10. Final report on special impact tests of plutonium shipping containers description of test results

    Bonzon, L.L.

    1977-02-01

    The results from tests conducted to determine the structural response of the LLD-1, Model 1518-6M, and FL-10 plutonium shipping packages when subjected to high-speed impacts (170 to 760 ft/sec) onto unyielding, concrete, and soil targets are presented

  11. Measurement of flows around modern commercial ship models

    Kim, W. J.; Van, S. H.; Kim, D. H.

    To document the details of flow characteristics around modern commercial ships, global force, wave pattern, and local mean velocity components were measured in the towing tank. Three modern commercial hull models of a container ship (KRISO container ship = KCS) and of two very large crude-oil carriers (VLCCs) with the same forebody and slightly different afterbody (KVLCC and KVLCC2) having bow and stern bulbs were selected for the test. Uncertainty analysis was performed for the measured data using the procedure recommended by the ITTC. Obtained experimental data will provide a good opportunity to explore integrated flow phenomena around practical hull forms of today. Those can be also used as the validation data for the computational fluid dynamics (CFD) code of both inviscid and viscous flow calculations.

  12. Measurement of flows around modern commercial ship models

    Kim, W J; Van, S H; Kim, D H [Korea Research Inst. of Ships and Ocean Engineering, KORDI, Taejon (Korea)

    2001-11-01

    To document the details of flow characteristics around modern commercial ships, global force, wave pattern, and local mean velocity components were measured in the towing tank. Three modern commercial hull models of a container ship (KRISO container ship = KCS) and of two very large crude-oil carriers (VLCCs) with the same forebody and slightly different afterbody (KVLCC and KVLCC2) having bow and stern bulbs were selected for the test. Uncertainty analysis was performed for the measured data using the procedure recommended by the ITTC. Obtained experimental data will provide a good opportunity to explore integrated flow phenomena around practical hull forms of today. Those can be also used as the validation data for the computational fluid dynamics (CFD) code of both inviscid and viscous flow calculations. (orig.)

  13. A Mathematical Model for Analysis on Ships Collision Avoidance ...

    This study develops a mathematical model for analysis on collision avoidance of ships. The obtained model provides information on the quantitative effect of the ship's engine's response and the applied reversing force on separation distance and stopping abilities of the ships. Appropriate evasive maneuvers require the ...

  14. EX1201: Ship Shakedown and Patch Tests on NOAA Ship Okeanos Explorer between 20100214 and 20120223

    National Oceanic and Atmospheric Administration, Department of Commerce — EX1201 is the 2012 shakedown mission of NOAA ship Okeanos Explorer (EX) and will perform system patch tests of the vessel’s Kongsberg EM302 multibeam sonar....

  15. Shipping

    Wijnolst, N.; Wergeland, T.

    1996-01-01

    Shipping is a multi-faceted industry which is rather complex to define from an academic point of view. This book attempts to grasp these complexities and provide the reader with an overview of the main topics and terminology in shipping. The book is based on material from our courses in shipping at the universities in Delft and Bergen. As with our lectures, we draw upon quite a va ried material, from research studies at a high academic level to lower level student work and purely descriptive ...

  16. Traffic simulation based ship collision probability modeling

    Goerlandt, Floris, E-mail: floris.goerlandt@tkk.f [Aalto University, School of Science and Technology, Department of Applied Mechanics, Marine Technology, P.O. Box 15300, FI-00076 AALTO, Espoo (Finland); Kujala, Pentti [Aalto University, School of Science and Technology, Department of Applied Mechanics, Marine Technology, P.O. Box 15300, FI-00076 AALTO, Espoo (Finland)

    2011-01-15

    Maritime traffic poses various risks in terms of human, environmental and economic loss. In a risk analysis of ship collisions, it is important to get a reasonable estimate for the probability of such accidents and the consequences they lead to. In this paper, a method is proposed to assess the probability of vessels colliding with each other. The method is capable of determining the expected number of accidents, the locations where and the time when they are most likely to occur, while providing input for models concerned with the expected consequences. At the basis of the collision detection algorithm lays an extensive time domain micro-simulation of vessel traffic in the given area. The Monte Carlo simulation technique is applied to obtain a meaningful prediction of the relevant factors of the collision events. Data obtained through the Automatic Identification System is analyzed in detail to obtain realistic input data for the traffic simulation: traffic routes, the number of vessels on each route, the ship departure times, main dimensions and sailing speed. The results obtained by the proposed method for the studied case of the Gulf of Finland are presented, showing reasonable agreement with registered accident and near-miss data.

  17. Ship

    Keuning, J.A.

    2008-01-01

    The invention concerns a ship designed for use at high speed and heavy seas having a single long and slender hull with a narrow beam and a more or less vertical bow, whereby the front half of the hull has more or less vertical sides, minimal flare in the bow sections and towards the bow an increase in draught at its center line combined with a more or less similar increase of freeboard and whereby the aft end of the hull has a flat or slightly V-shaped bottom with one or more propellers and/o...

  18. EX1101: Ship Shakedown and Patch Tests on NOAA Ship Okeanos Explorer between March 16 and April 1, 2011

    National Oceanic and Atmospheric Administration, Department of Commerce — This project will involve the shakedown of all Okeanos Explorer ship capabilities and a patch test of the Kongsberg EM302 multibeam system. Operations for this...

  19. Manipulating ship fuel sulfur content and modeling the effects on air quality and climate

    Partanen, Antti-Ilari; Laakso, Anton; Schmidt, Anja; Kokkola, Harri; Kuokkanen, Tuomas; Kerminen, Veli-Matti; Lehtinen, Kari E. J.; Laakso, Lauri; Korhonen, Hannele

    2013-04-01

    Aerosol emissions from international shipping are known to cause detrimental health effects on people mainly via increased lung cancer and cardiopulmonary diseases. On the other hand, the aerosol particles from the ship emissions modify the properties of clouds and are believed to have a significant cooling effect on the global climate. In recent years, aerosol emissions from shipping have been more strictly regulated in order to improve air quality and thus decrease the mortality due to ship emissions. Decreasing the aerosol emissions from shipping is projected to decrease their cooling effect, which would intensify the global warming even further. In this study, we use a global aerosol-climate model ECHAM5.5-HAM2 to test if continental air quality can be improved while still retaining the cooling effect from shipping. The model explicitly resolves emissions of aerosols and their pre-cursor gases. The model also calculates the interaction between aerosol particles and clouds, and can thus predict the changes in cloud properties due to aerosol emissions. We design and simulate a scenario where ship fuel sulfur content is strictly limited to 0.1% near all coastal regions, but doubled in the open oceans from the current global mean value of 2.7% (geo-ships). This scenario is compared to three other simulations: 1) No shipping emissions at all (no-ships), 2) present-day shipping emissions (std-ships) and 3) a future scenario where sulfur content is limited to 0.1% in the coastal zones and to 0.5% in the open ocean (future-ships). Global mean radiative flux perturbation (RFP) in std-ships compared to no-ships is calculated to be -0.4 W m-2, which is in the range of previous estimates for present-day shipping emissions. In the geo-ships simulation the corresponding global mean RFP is roughly equal, but RFP is spatially distributed more on the open oceans, as expected. In future-ships the decreased aerosol emissions provide weaker cooling effect of only -0.1 W m-2. In

  20. Testing and evaluation of used UF6 shipping packages

    Barlow, C.R.; Ziehlke, K.T.; Pryor, W.A.; Housholder, W.R.

    1986-01-01

    Damage to shipping packages and their components, whether due to normal environmental exposure or because of unforeseen accidents, requires occasional reevaluation and requalification to assure the suitability of the packages for continued service. Pressure tests have been conducted on used 30B cylinders that were involved in a warehouse fire to assess the possible damaging effects of the exposure. Deteriorated and mechanically damaged overpacks which had absorbed large quantities of water in service were subjected to drying tests, foam properties were evaluated, and a rehabilitation procedure was developed to allow return of such packages to service. Protective shipping packages show deterioration with extended service, principally structural damage from rough handling and rust damage from exposure to weather and from storage practices which may promote absorption of water by the insulating foam. The structural and thermal properties of the phenolic foam insulation from used shipping packages were found to be not adversely affected by absorbed water, and they were not degraded by the drying process. In order to slow or avoid continuing rust damage in renovated packages, however, a process was developed for drying the foam in commercial facilities prior to restoration work on used or damaged containers. Two 2-1/2-ton steel transport cylinders, type 30B, were involved in a warehouse fire where portions of the cylinders were estimated to have reached a temperature of 1600 0 F. The cylinders were empty at the time of the fire and thus were not in the protective packages in which full product cylinders are handled while in transit. Hydrostatic burst tests showed that the integrity of the cylinders was not degraded by the fire exposure. They withstood test pressures in excess of 10 times the design pressure, and showed a volume expansion of 30% above the original capacity before rupturing in a completely ductile fashion

  1. Evaluation of Differentiation Strategy in Shipping Enterprises with Simulation Model

    Vaxevanou, Anthi Z.; Ferfeli, Maria V.; Damianos, Sakas P.

    2009-08-01

    The present inquiring study aims at investigating the circumstances that prevail in the European Shipping Enterprises with special reference to the Greek ones. This investigation is held in order to explore the potential implementation of strategies so as to create a unique competitive advantage [1]. The Shipping sector is composed of enterprises that are mainly activated in the following three areas: the passenger, the commercial and the naval. The main target is to create a dynamic simulation model which, with reference to the STAIR strategic model, will evaluate the strategic differential choice that some of the shipping enterprises have.

  2. Validity of scale modeling for large deformations in shipping containers

    Burian, R.J.; Black, W.E.; Lawrence, A.A.; Balmert, M.E.

    1979-01-01

    The principal overall objective of this phase of the continuing program for DOE/ECT is to evaluate the validity of applying scaling relationships to accurately assess the response of unprotected model shipping containers severe impact conditions -- specifically free fall from heights up to 140 ft onto a hard surface in several orientations considered most likely to produce severe damage to the containers. The objective was achieved by studying the following with three sizes of model casks subjected to the various impact conditions: (1) impact rebound response of the containers; (2) structural damage and deformation modes; (3) effect on the containment; (4) changes in shielding effectiveness; (5) approximate free-fall threshold height for various orientations at which excessive damage occurs; (6) the impact orientation(s) that tend to produce the most severe damage; and (7) vunerable aspects of the casks which should be examined. To meet the objective, the tests were intentionally designed to produce extreme structural damage to the cask models. In addition to the principal objective, this phase of the program had the secondary objectives of establishing a scientific data base for assessing the safety and environmental control provided by DOE nuclear shipping containers under impact conditions, and providing experimental data for verification and correlation with dynamic-structural-analysis computer codes being developed by the Los Alamos Scientific Laboratory for DOE/ECT

  3. Technical and management considerations in conducting type B shipping container tests

    Whitney, M.A.; Leader, D.R.; Phipps, D.P.

    1994-01-01

    The Code of Federal Regulations (CFR) mandate that type B shipping containers are capable of surviving specific drop tests. One approach for demonstrating compliance to the CFRs is to drop test a shipping container. This paper will discuss the technical and management considerations in conducting such drop tests on the 9975 family of shipping containers. For both technical and management considerations this paper will comment on loading the shipping container, dropping the shopping container, and examination of the shipping container after the drop tests

  4. 46 CFR 154.431 - Model test.

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Model test. 154.431 Section 154.431 Shipping COAST GUARD... Model test. (a) The primary and secondary barrier of a membrane tank, including the corners and joints...(c). (b) Analyzed data of a model test for the primary and secondary barrier of the membrane tank...

  5. 46 CFR 154.449 - Model test.

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Model test. 154.449 Section 154.449 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF... § 154.449 Model test. The following analyzed data of a model test of structural elements for independent...

  6. Parameter Identification of Ship Maneuvering Models Using Recursive Least Square Method Based on Support Vector Machines

    Man Zhu

    2017-03-01

    Full Text Available Determination of ship maneuvering models is a tough task of ship maneuverability prediction. Among several prime approaches of estimating ship maneuvering models, system identification combined with the full-scale or free- running model test is preferred. In this contribution, real-time system identification programs using recursive identification method, such as the recursive least square method (RLS, are exerted for on-line identification of ship maneuvering models. However, this method seriously depends on the objects of study and initial values of identified parameters. To overcome this, an intelligent technology, i.e., support vector machines (SVM, is firstly used to estimate initial values of the identified parameters with finite samples. As real measured motion data of the Mariner class ship always involve noise from sensors and external disturbances, the zigzag simulation test data include a substantial quantity of Gaussian white noise. Wavelet method and empirical mode decomposition (EMD are used to filter the data corrupted by noise, respectively. The choice of the sample number for SVM to decide initial values of identified parameters is extensively discussed and analyzed. With de-noised motion data as input-output training samples, parameters of ship maneuvering models are estimated using RLS and SVM-RLS, respectively. The comparison between identification results and true values of parameters demonstrates that both the identified ship maneuvering models from RLS and SVM-RLS have reasonable agreements with simulated motions of the ship, and the increment of the sample for SVM positively affects the identification results. Furthermore, SVM-RLS using data de-noised by EMD shows the highest accuracy and best convergence.

  7. Modeling and Measurements of Alternating Magnetic Signatures of Ships

    Zhiqiang Wu

    2015-03-01

    Full Text Available The alternating electric and magnetic fields are new contributors to the global electromagnetic silencing of ships. Thus, modeling and measurements of alternating magnetic signatures should be a research priority in maritime engineering. In this paper, an alternating horizontal electric dipole is adopted to model the electromagnetic fields related with corrosion. Formulas for alternating magnetic fields generated in shallow sea by horizontal electric dipole are derived based on an air-sea-seabed three-layered model and a numerical computer is also applied. In addition, the alternating magnetic fields of a ship are measured using a tri-axis fluxgate magnetometer fixed in a swaying platform. The characteristics of these fields are analyzed. Finally, the equivalent dipole moment of the trial ship is predicted by contrasting the model results and the observed data.

  8. Surface Ship Shock Modeling and Simulation: Two-Dimensional Analysis

    Young S. Shin

    1998-01-01

    Full Text Available The modeling and simulation of the response of a surface ship system to underwater explosion requires an understanding of many different subject areas. These include the process of underwater explosion events, shock wave propagation, explosion gas bubble behavior and bubble-pulse loading, bulk and local cavitation, free surface effect, fluid-structure interaction, and structural dynamics. This paper investigates the effects of fluid-structure interaction and cavitation on the response of a surface ship using USA-NASTRAN-CFA code. First, the one-dimensional Bleich-Sandler model is used to validate the approach, and second, the underwater shock response of a two-dimensional mid-section model of a surface ship is predicted with a surrounding fluid model using a constitutive equation of a bilinear fluid which does not allow transmission of negative pressures.

  9. Compact Polarimetric SAR Ship Detection with m-δ Decomposition Using Visual Attention Model

    Lu Xu

    2016-09-01

    Full Text Available A few previous studies have illustrated the potentials of compact polarimetric Synthetic Aperture Radar (CP SAR in ship detection. In this paper, we design a ship detection algorithm of CP SAR from the perspective of computer vision. A ship detection algorithm using the pulsed cosine transform (PCT visual attention model is proposed to suppress background clutter and highlight conspicuous ship targets. It is the first time that a visual attention model is introduced to CP SAR application. The proposed algorithm is a quick and complete framework for practical use. Polarimetric features—the relative phase δ and volume scattering component—are extracted from m-δ decomposition to eliminate false alarms and modify the PCT model. The constant false alarm rate (CFAR algorithm based on lognormal distribution is adopted to detect ship targets, after a clutter distribution fitting procedure of the modified saliency map. The proposed method is then tested on three simulated circular-transmit-linear-receive (CTLR mode images, which covering East Sea of China. Compared with the detection results of SPAN and the saliency map with only single-channel amplitude, the proposed method achieves the highest detection rates and the lowest misidentification rate and highest figure of merit, proving the effectiveness of polarimetric information of compact polarimetric SAR ship detection and the enhancement from the visual attention model.

  10. A Fully Nonlinear, Dynamically Consistent Numerical Model for Solid-Body Ship Motion. I. Ship Motion with Fixed Heading

    Lin, Ray-Quing; Kuang, Weijia

    2011-01-01

    In this paper, we describe the details of our numerical model for simulating ship solidbody motion in a given environment. In this model, the fully nonlinear dynamical equations governing the time-varying solid-body ship motion under the forces arising from ship wave interactions are solved with given initial conditions. The net force and moment (torque) on the ship body are directly calculated via integration of the hydrodynamic pressure over the wetted surface and the buoyancy effect from the underwater volume of the actual ship hull with a hybrid finite-difference/finite-element method. Neither empirical nor free parametrization is introduced in this model, i.e. no a priori experimental data are needed for modelling. This model is benchmarked with many experiments of various ship hulls for heave, roll and pitch motion. In addition to the benchmark cases, numerical experiments are also carried out for strongly nonlinear ship motion with a fixed heading. These new cases demonstrate clearly the importance of nonlinearities in ship motion modelling.

  11. Inspection, testing, and operating requiremens for the packaging and shipping of uranium trioxide in 55-gallon Department of Transportation (DOT) Specification 6M shipping packagings

    Toomer, D.V.

    1991-06-01

    This document identifies the inspection, testing and operating requirements for the packaging, loading, and shipping of uranium trioxide (UO 3 ) in 55-gallon DOT Specification 6M shipping packagings from the Idaho Chemical Processing Plant (ICPP). Compliance with this document assures established controls for the purchasing, packaging, loading, and shipping of DOT Specification 6M shipping packagings are maintained in strict accordance with applicable Code of Federal Regulations (CFRs) and Department of Energy (DOE) Orders. 7 refs., 3 figs., 1 tab

  12. Modelling of the Internal Mechanics in Ship Collisions

    Paik, Jeom Kee; Pedersen, Preben Terndrup

    1996-01-01

    A method for analysis of the structural damage due to ship collisions is developed. The method is based on the idealized structural unit method (ISUM). Longitudinal/transverse webs which connect the outer and the inner hulls are modelled by rectangular plate units. The responses are determined...... on the stiffness and the strength is considered as well. In order to include the coupling effects between local and global failure of the structure, the usual non-linear finite-element technique is applied. In order to deal with the gap and contact conditions between the striking and the struck ships, gap......-skin plated structures in collision/grounding situations with the present solutions. As an illustrative example the procedure has been used for analyses of a side collision of a double-hull tanker. Several factors affecting ship collision response, namely the collision speed and the scantlings/ arrangements...

  13. Safety analysis report on Model UC-609 shipping package

    Sandberg, R.R.

    1977-08-01

    This Safety Analysis Report for Packaging demonstrates that model UC-609 shipping package can safely transport tritium in any of its forms. The package and its contents are described. The package when subjected to the transport conditions specified in the Code of Federal Regulations, Title 10, Part 71 is evaluated. Finally, compliance with these regulations is discussed

  14. Innovative technologies to accurately model waves and moored ship motions

    van der Molen, W

    2010-09-01

    Full Text Available Late in 2009 CSIR Built Environment in Stellenbosch was awarded a contract to carry out extensive physical and numerical modelling to study the wave conditions and associated moored ship motions, for the design of a new iron ore export jetty for BHP...

  15. A review of a radioactive material shipping container including design, testing, upgrading compliance program and shipping logistics

    Celovsky, A.; Lesco, R.; Gale, B.; Sypes, J.

    2003-01-01

    Ten years ago Atomic Energy of Canada developed a Type B(U)-85 shipping container for the global transport of highly radioactive materials. This paper reviews the development of the container, including a summary of the design requirements, a review of the selected materials and key design elements, and the results of the major qualification tests (drop testing, fire test, leak tightness testing, and shielding integrity tests). As a result of the testing, improvements to the structural, thermal and containment design were made. Such improvements, and reasons thereof, are noted. Also provided is a summary of the additional analysis work required to upgrade the package from a Type B(U) to a Type B(F), i.e. essentially upgrading the container to include fissile radioisotopes to the authorized radioactive contents list. Having a certified shipping container is only one aspect governing the global shipments of radioactive material. By necessity the shipment of radioactive material is a highly regulated environment. This paper also explores the experiences with other key aspects of radioactive shipments, including the service procedures used to maintain the container certification, the associated compliance program for radioactive material shipments, and the shipping logistics involved in the transport. (author)

  16. Modeling for Ship Power System Emulation

    2009-05-08

    used repeatedly for load- identification in shipboard environments (3). The NILM may be able to improve the HSR performance by identifying...electric plant. One of the major reasons for the hardware emulator is to test the NILM in a ring distribution lineup to evaluate if power to particular

  17. Modeling and Solving the Liner Shipping Service Selection Problem

    Karsten, Christian Vad; Balakrishnan, Anant

    We address a tactical planning problem, the Liner Shipping Service Selection Problem (LSSSP), facing container shipping companies. Given estimated demand between various ports, the LSSSP entails selecting the best subset of non-simple cyclic sailing routes from a given pool of candidate routes...... to accurately model transshipment costs and incorporate routing policies such as maximum transit time, maritime cabotage rules, and operational alliances. Our hop-indexed arc flow model is smaller and easier to solve than path flow models. We outline a preprocessing procedure that exploits both the routing...... requirements and the hop limits to reduce problem size, and describe techniques to accelerate the solution procedure. We present computational results for realistic problem instances from the benchmark suite LINER-LIB....

  18. Flow measurement around a model ship with propeller and rudder

    Van, S H; Yoon, H S; Lee, Y Y; Park, I R [Korea Research Institute of Ships and Ocean Engineering, KORDI, Marine Transportation Systems Laboratory, Daejeon (Korea); Kim, W J [Mokpo National University, Department of Naval Architecture and Marine Engineering, Jeonnam (Korea)

    2006-04-15

    For the design of hull forms with better resistance and propulsive performance, it is essential to understand flow characteristics, such as wave and wake development, around a ship. Experimental data detailing the local flow characteristics are invaluable for the validation of the physical and numerical modeling of computational fluid dynamics (CFD) codes, which are recently gaining attention as efficient tools for hull form evaluation. This paper describes velocity and wave profiles measured in the towing tank for the KRISO 138,000 m{sup 3} LNG carrier model with propeller and rudder. The effects of propeller and rudder on the wake and wave profiles in the stern region are clearly identified. The results contained in this paper can provide an opportunity to explore integrated flow phenomena around a model ship in the self-propelled condition, and can be added to the International Towing Tank Conference benchmark data for CFD validation as the previous KCS and KVLCC cases. (orig.)

  19. Flow measurement around a model ship with propeller and rudder

    van, S. H.; Kim, W. J.; Yoon, H. S.; Lee, Y. Y.; Park, I. R.

    2006-04-01

    For the design of hull forms with better resistance and propulsive performance, it is essential to understand flow characteristics, such as wave and wake development, around a ship. Experimental data detailing the local flow characteristics are invaluable for the validation of the physical and numerical modeling of computational fluid dynamics (CFD) codes, which are recently gaining attention as efficient tools for hull form evaluation. This paper describes velocity and wave profiles measured in the towing tank for the KRISO 138,000 m3 LNG carrier model with propeller and rudder. The effects of propeller and rudder on the wake and wave profiles in the stern region are clearly identified. The results contained in this paper can provide an opportunity to explore integrated flow phenomena around a model ship in the self-propelled condition, and can be added to the International Towing Tank Conference benchmark data for CFD validation as the previous KCS and KVLCC cases.

  20. Design and modelling of innovative machinery systems for large ships

    Larsen, Ulrik

    Eighty percent of the growing global merchandise trade is transported by sea. The shipping industry is required to reduce the pollution and increase the energy efficiency of ships in the near future. There is a relatively large potential for approaching these requirements by implementing waste heat...... consisting of a two-zone combustion and NOx emission model, a double Wiebe heat release model, the Redlich-Kwong equation of state and the Woschni heat loss correlation. A novel methodology is presented and used to determine the optimum organic Rankine cycle process layout, working fluid and process......, are evaluated with regards to the fuel consumption and NOx emissions trade-off. The results of the calibration and validation of the engine model suggest that the main performance parameters can be predicted with adequate accuracies for the overall purpose. The results of the ORC and the Kalina cycle...

  1. Gaussian mixture models-based ship target recognition algorithm in remote sensing infrared images

    Yao, Shoukui; Qin, Xiaojuan

    2018-02-01

    Since the resolution of remote sensing infrared images is low, the features of ship targets become unstable. The issue of how to recognize ships with fuzzy features is an open problem. In this paper, we propose a novel ship target recognition algorithm based on Gaussian mixture models (GMMs). In the proposed algorithm, there are mainly two steps. At the first step, the Hu moments of these ship target images are calculated, and the GMMs are trained on the moment features of ships. At the second step, the moment feature of each ship image is assigned to the trained GMMs for recognition. Because of the scale, rotation, translation invariance property of Hu moments and the power feature-space description ability of GMMs, the GMMs-based ship target recognition algorithm can recognize ship reliably. Experimental results of a large simulating image set show that our approach is effective in distinguishing different ship types, and obtains a satisfactory ship recognition performance.

  2. Desertions in nineteenth-century shipping: modelling quit behaviour

    Jari Ojala; Jaakko Pehkonen; Jari Eloranta

    2013-01-01

    Ship jumping in foreign ports was widespread throughout the age of sail. Desertion by seamen was illegal, it occurred abroad, and men who deserted only seldom returned home. We analyse desertion quantitatively and link it to the broader question of quit behaviour and labour turnover. Though the better wages paid at the foreign ports were the main reason for desertion, the regression model of the determinants of desertion indicates that outside opportunities, such as migration, and monetary in...

  3. Modelling ship operational reliability over a mission under regular inspections

    Christer, A.H.; Lee, S.K.

    1997-01-01

    A ship is required to operate for a fixed mission period. Should a critical item of equipment fail at sea, the ship is subject to a costly event with potentially high risk to ship and crew. Given warning of a pending defect, the ship can try to return to port under its own power and thus attempt to

  4. Documentation for initial testing and inspections of Beneficial Uses Shipping System (BUSS) Cask

    Lundeen, J.E.

    1994-01-01

    The purpose of this report is to compile data generated during the initial tests and inspections of the Beneficial Uses Shipping System (BUSS) Cask. In addition, this report will verify that the testing criteria identified in section 8.1 of the BUSS Cask Safety Analysis Report for Packaging (SARP) was met. The BUSS Cask Model R-1 is a type B shipping container used for shipment of radioactive cesium-137 and strontium-90 capsules to Waste Encapsulation and Storage Facility (WESF). The BUSS Cask body and lid are each one-piece forgings fabricated from ASTM A473, Type 304 stainless steel. The primary purpose of the BUSS Cask is to provide shielding and confinement as well as impact, puncture, and thermal protection for the capsules under both normal and accident conditions. Chapter 8 of the BUSS Cask SARP requires several acceptance tests and inspections, each intended to evaluate the performance of different components of the BUSS Cask system, to be performed before its first use. The results of the tests and inspections required are included in this document

  5. Shielding tests for a new ship for the transport of spent nuclear fuels

    Ito, D.; Kitano, T.; Akiyama, H.; Ueki, K.; Sanui, T.

    1998-01-01

    a new ship for the transport of spent nuclear fuels which uses serpentine concrete as its major shielding material has been constructed. The shielding calculations are based on DOT3.5 code (CCC-276) and the DLC23). Experiments with Cf-252 and Co-60 sources were carried out to confirm the validity of this method of calculating the shielding effectiveness of serpentine concrete. In these experiments, neutron and gamma-ray dose equivalent rates were measured in various arrangements to simulate the shielding structures of the ship, the calculations for each arrangement were performed by this shielding calculation method. For both neutron and gamma-rays, the calculation results agreed with the experiments very well, confirming that this calculation method used in the ship's shielding design is valid. Two kinds of on-board gamma-ray shielding tests were performed to confirm the ship's actual shielding effectiveness. In one kind of test, gamma-ray dose equivalent rates were measured for each shielding wall using Co-60 sources. In the other kind of test, gamma-ray dose equivalent rates in the ship's accommodation area were measured when a strong Co-60 source was placed in a loaded shipping cask's position. In both gamma-ray shielding tests all measured dose equivalent rates were less than the calculated values, confirming that the ship's actual shielding is sufficient to meet safety requirements. (authors)

  6. Modeling fires in adjacent ship compartments with computational fluid dynamics

    Wix, S.D.; Cole, J.K.; Koski, J.A.

    1998-01-01

    This paper presents an analysis of the thermal effects on radioactive (RAM) transportation pack ages with a fire in an adjacent compartment. An assumption for this analysis is that the adjacent hold fire is some sort of engine room fire. Computational fluid dynamics (CFD) analysis tools were used to perform the analysis in order to include convective heat transfer effects. The analysis results were compared to experimental data gathered in a series of tests on the United States Coast Guard ship Mayo Lykes located at Mobile, Alabama. (authors)

  7. Development of methodology for certification of Type B shipping containers using analytical and testing techniques

    Sharp, R.R.; Varley, D.T.

    1993-01-01

    The use of multidisciplinary teams to develop Type B shipping containers improves the quality and reliability of these reusable packagings. Including the people involved in all aspects of the design, certification and use of the package leads to more innovative, user-friendly containers. Concurrent use of testing and analysis allows engineers to more fully characterize a shipping container's responses to the environments given in the regulations, and provides a strong basis for certification. The combination of the input and output of these efforts should provide a general methodology that designers of Type B radioactive material shipping containers can utilize to optimize and certify their designs. (J.P.N.)

  8. Implications of the Baltimore Rail Tunnel Fire for Full-Scale Testing of Shipping Casks

    Halstead, R. J.; Dilger, F.

    2003-01-01

    The U.S. Nuclear Regulatory Commission (NRC) does not currently require full-scale physical testing of shipping casks as part of its certification process. Stakeholders have long urged NRC to require full-scale testing as part of certification. NRC is currently preparing a full-scale casktesting proposal as part of the Package Performance Study (PPS) that grew out of the NRC reexamination of the Modal Study. The State of Nevada and Clark County remain committed to the position that demonstration testing would not be an acceptable substitute for a combination of full-scale testing, scale-model tests, and computer simulation of each new cask design prior to certification. Based on previous analyses of cask testing issues, and on preliminary findings regarding the July 2001 Baltimore rail tunnel fire, the authors recommend that NRC prioritize extra-regulatory thermal testing of a large rail cask and the GA-4 truck cask under the PPS. The specific fire conditions and other aspects of the full-scale extra-regulatory tests recommended for the PPS are yet to be determined. NRC, in consultation with stakeholders, must consider past real-world accidents and computer simulations to establish temperature failure thresholds for cask containment and fuel cladding. The cost of extra-regulatory thermal testing is yet to be determined. The minimum cost for regulatory thermal testing of a legal-weight truck cask would likely be $3.3-3.8 million

  9. Ship board testing of a deoxygenation ballast water treatment.

    McCollin, Tracy; Quilez-Badia, Gemma; Josefsen, Kjell D; Gill, Margaret E; Mesbahi, Ehsan; Frid, Chris L J

    2007-08-01

    A ship board trial of a deoxygenation method for treating ballast water was carried out during a voyage from Southampton (United Kingdom) to Manzanillo (Panama). A nutrient solution added to two ballast tanks encouraged bacterial growth, resulting in a gradual change to an anoxic environment. Samples were taken from two treated tanks and two untreated tanks to assess changes in the abundance and viability of zooplankton, phytoplankton and bacteria. The work was carried out before the International Maritime Organization (IMO) standard was agreed so only a broad indication of whether the results achieved the standard was given. For the zooplankton, the standard would have been achieved within 5 or 7 days but the phytoplankton results were inconclusive. The biological efficacy was the result of the combination of several factors, including the treatment, pump damage and an increase in the water temperature during the voyage.

  10. Detecting ship targets in spaceborne infrared image based on modeling radiation anomalies

    Wang, Haibo; Zou, Zhengxia; Shi, Zhenwei; Li, Bo

    2017-09-01

    Using infrared imaging sensors to detect ship target in the ocean environment has many advantages compared to other sensor modalities, such as better thermal sensitivity and all-weather detection capability. We propose a new ship detection method by modeling radiation anomalies for spaceborne infrared image. The proposed method can be decomposed into two stages, where in the first stage, a test infrared image is densely divided into a set of image patches and the radiation anomaly of each patch is estimated by a Gaussian Mixture Model (GMM), and thereby target candidates are obtained from anomaly image patches. In the second stage, target candidates are further checked by a more discriminative criterion to obtain the final detection result. The main innovation of the proposed method is inspired by the biological mechanism that human eyes are sensitive to the unusual and anomalous patches among complex background. The experimental result on short wavelength infrared band (1.560 - 2.300 μm) and long wavelength infrared band (10.30 - 12.50 μm) of Landsat-8 satellite shows the proposed method achieves a desired ship detection accuracy with higher recall than other classical ship detection methods.

  11. Ship Domain Model for Multi-ship Collision Avoidance Decision-making with COLREGs Based on Artificial Potential Field

    TengFei Wang

    2017-03-01

    Full Text Available A multi-ship collision avoidance decision-making and path planning formulation is studied in a distributed way. This paper proposes a complete set of solutions for multi-ship collision avoidance in intelligent navigation, by using a top-to-bottom organization to structure the system. The system is designed with two layers: the collision avoidance decision-making and the path planning. Under the general requirements of the International Regulations for Preventing Collisions at Sea (COLREGs, the performance of distributed path planning decision-making for anti-collision is analyzed for both give-way and stand-on ships situations, including the emergency actions taken by the stand-on ship in case of the give-way ship’s fault of collision avoidance measures. The Artificial Potential Field method(APF is used for the path planning in details. The developed APF method combined with the model of ship domain takes the target ships’ speed and course in-to account, so that it can judge the moving characteristics of obstacles more accurately. Simulation results indicate that the system proposed can work effectiveness.

  12. Model of Optimal Cargo Transport Structure by Full Container Ship on Predefined Sailing Route

    Serđo Kos

    2004-01-01

    Full Text Available This paper presents the mathematical model for solving theproblem of defining optimal cargo transport structure, occurringwhen, on a predefined sailing route, adequate number ofcontainers of various types, masses and sizes, possibly includingRO!RO cargo, is to be selected, i.e., a "container lot" is to beestablished in loading ports with the aim of gaining maximumship profit and, at the same time, of exploiting useful load andtransport capacity of container ship as much as possible. Theimplementation of the proposed model enables considerableincrease in the efficiency of container ship operations. Themodel was tested using a numerical example with real data.The applied post-optimal analysis examines the influence ofchange in some values of the mathematical model on the resultingoptimal program.

  13. An intermodal transportation geospatial network modeling for containerized soybean shipping

    Xiang Liu

    2017-06-01

    Full Text Available Containerized shipping is a growing market for agricultural exports, particularly soybeans. In order to understand the optimal strategies for improving the United States’ economic competitiveness in this emerging market, this research develops an intermodal transportation network modeling framework, focusing on U.S. soybean container shipments. Built upon detailed modal cost analyses, a Geospatial Intermodal Freight Transportation (GIFT model has been developed to understand the optimal network design for U.S. soybean exports. Based on market demand and domestic supply figures, the model is able to determine which domestically produced soybeans should go to which foreign markets, and by which transport modes. This research and its continual studies, will provide insights into future policies and practices that can improve the transportation efficiency of soybean logistics.

  14. EX1301: Ship Shakedown and Patch Test Exploration, NE Canyons and Seamounts on NOAA Ship Okeanos Explorer between 20130318 and 20130405

    National Oceanic and Atmospheric Administration, Department of Commerce — Following annual ship shakedown and patch tests, EX1301 will complete the comprehensive mapping of the Northeast canyons and the adjacent continental shelf carried...

  15. Test plan/procedure for the SPM-1 shipping container system. Revision 0

    Flanagan, B.D.

    1995-01-01

    The 49 CFR 173.465 Type A packaging tests will verify that SPM-1 will provide adequate protection and pass as a Type A package. Test will determine that the handle of the Pig will not penetrate through the plywood spacer and rupture the shipping container. Test plan/procedure provides planning, pre-test, setup, testing, and post-testing guidelines and procedures for conducting the open-quotes Free Drop Testclose quotes procedure for the SPM-1 package

  16. Full scale impact testing for environmental and safety control of energy material shipping container systems

    Seagren, R.D.

    1978-01-01

    Heavily-shielded energy material shipping systems, similar in size and weight to those presently employed to transport irradiated reactor fuel elements, are being destructively tested under dynamic conditions. In these tests, the outer and inner steel shells interact in a complex manner with the massive biological shielding in the system. Results obtained from these tests provide needed information for new design concepts. Containment failure (and the resulting release of radioactive material to the environment which might occur in an extremely severe accident) is most likely through the seals and other ancillary features of the shipping systems. Analyses and experiments provide engineering data on the behavior of these shipping systems under severe accident conditions and information for predicting potential survivability and environmental control with a rational margin of safety

  17. 76 FR 34145 - Safety Zone, Barrier Testing Operations, Chicago Sanitary and Ship Canal, Romeoville, IL

    2011-06-13

    ...-AA00 Safety Zone, Barrier Testing Operations, Chicago Sanitary and Ship Canal, Romeoville, IL AGENCY.... Construction on Barrier IIB has been completed. Operational and safety testing was conducted in February 2011... dispersal barrier IIA and IIB. This safety zone will be enforced daily from 7 a.m. to 11 a.m. and from 1 p.m...

  18. Model for Environmental Assessment of Container Ship Transport

    Kristensen, Hans Otto Holmegaard

    2012-01-01

    of these parameters on the EEDI. It is found possible to reduce EEDI by roughly 20 % without reducing ship speed, but only by changing some of the design parameters, such as reducing the sea margin by using a derated main engine, increasing the length of the ship by 5 %, and reducing steel weight by 3 % via steel...

  19. Shielding designs and tests of a new exclusive ship for transporting spent nuclear fuels

    Ono, M.; Ito, D.; Kitano, T.; Ueki, K.; Akiyama, H.; Obara, I.; Sanui, T.

    2000-01-01

    The Rokuei-Maru, a ship built specially for the transport of spent nuclear fuels in casks, was launched April in 1996. She is the first ship to comply with special Japanese regulations, KAISA 520, based on the INF code. DOT3.5 and MCNP-4A were used for the evaluation of dose equivalent rates of her shielding structures. On-board gamma-ray shielding tests were executed to confirm the effectiveness of the ship's shielding performance. The tests confirmed that effective shielding has been achieved and the dose equivalent rate in the accommodation and other inhabited spaces is sufficiently lower than the regulated limitations. This was achieved by employing the appropriate calculation methods and shielding materials. (author)

  20. 3D forward modeling and response analysis for marine CSEMs towed by two ships

    Zhang, Bo; Yin, Chang-Chun; Liu, Yun-He; Ren, Xiu-Yan; Qi, Yan-Fu; Cai, Jing

    2018-03-01

    A dual-ship-towed marine electromagnetic (EM) system is a new marine exploration technology recently being developed in China. Compared with traditional marine EM systems, the new system tows the transmitters and receivers using two ships, rendering it unnecessary to position EM receivers at the seafloor in advance. This makes the system more flexible, allowing for different configurations (e.g., in-line, broadside, and azimuthal and concentric scanning) that can produce more detailed underwater structural information. We develop a three-dimensional goal-oriented adaptive forward modeling method for the new marine EM system and analyze the responses for four survey configurations. Oceanbottom topography has a strong effect on the marine EM responses; thus, we develop a forward modeling algorithm based on the finite-element method and unstructured grids. To satisfy the requirements for modeling the moving transmitters of a dual-ship-towed EM system, we use a single mesh for each of the transmitter locations. This mitigates the mesh complexity by refining the grids near the transmitters and minimizes the computational cost. To generate a rational mesh while maintaining the accuracy for single transmitter, we develop a goal-oriented adaptive method with separate mesh refinements for areas around the transmitting source and those far away. To test the modeling algorithm and accuracy, we compare the EM responses calculated by the proposed algorithm and semi-analytical results and from published sources. Furthermore, by analyzing the EM responses for four survey configurations, we are confirm that compared with traditional marine EM systems with only in-line array, a dual-ship-towed marine system can collect more data.

  1. SAR Imagery Simulation of Ship Based on Electromagnetic Calculations and Sea Clutter Modelling for Classification Applications

    Ji, K F; Zhao, Z; Xing, X W; Zou, H X; Zhou, S L

    2014-01-01

    Ship detection and classification with space-borne SAR has many potential applications within the maritime surveillance, fishery activity management, monitoring ship traffic, and military security. While ship detection techniques with SAR imagery are well established, ship classification is still an open issue. One of the main reasons may be ascribed to the difficulties on acquiring the required quantities of real data of vessels under different observation and environmental conditions with precise ground truth. Therefore, simulation of SAR images with high scenario flexibility and reasonable computation costs is compulsory for ship classification algorithms development. However, the simulation of SAR imagery of ship over sea surface is challenging. Though great efforts have been devoted to tackle this difficult problem, it is far from being conquered. This paper proposes a novel scheme for SAR imagery simulation of ship over sea surface. The simulation is implemented based on high frequency electromagnetic calculations methods of PO, MEC, PTD and GO. SAR imagery of sea clutter is modelled by the representative K-distribution clutter model. Then, the simulated SAR imagery of ship can be produced by inserting the simulated SAR imagery chips of ship into the SAR imagery of sea clutter. The proposed scheme has been validated with canonical and complex ship targets over a typical sea scene

  2. Development and testing of control rod drives for ship reactors

    Bruelheide, K.; Mundt, D.; Peters, C.-H.; Manthey, H.-J.

    1978-01-01

    The following paper deals with the development and testings of a new control rod drive design for marine reactors. Starting from the good operating experience with the advanced pressurized water reactor (FDR) of the NS OTTO HAHN a control rod drive system with an hermetically sealed drive principle was developed. A prototype control rod drive system was put through extensive tests and developed ready for standard production at the 'Gesellschaft fuer Kernenergieverwertung in Schiffbau und Schiffahrt'

  3. Modeling of Ship Collision Risk Index Based on Complex Plane and Its Realization

    Xiaoqin Xu; Xiaoqiao Geng; Yuanqiao Wen

    2016-01-01

    Ship collision risk index is the basic and important concept in the domain of ship collision avoidance. In this paper, the advantages and deficiencies of the various calculation methods of ship collision risk index are pointed out. Then the ship collision risk model based on complex plane, which can well make up for the deficiencies of the widely-used evaluation model proposed by Kearon.J and Liu ruru is proposed. On this basis, the calculation method of collision risk index under the encount...

  4. Analysis of the qualification test standards for small radioactive material shipping packages

    McClure, J.D.

    1978-01-01

    The study compares the severity of the existing regulatory standards which are used to license radioactive material (RAM) shipping packages with the severity of transportation accidents. The basic findings of the study indicate that the present regulatory standards provide significantly higher levels of protection for surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It was also determined that crush can occur in all of the transport modes and is not presently included in existing regulations for accident conditions. Test proposals are included for the surface transport mode (truck, rail) and the air transport mode

  5. Unreliable alcohol testing in a shipping safety programme.

    Helander, Anders; Hagelberg, Charlotte Asker; Beck, Olof; Petrini, Björn

    2009-08-10

    Within a maritime alcohol and drug testing programme, a case showing an unphysiological urine ethanol concentration (235 mmol/L, 10.8 g/L) was found. The sample contained low levels of the ethanol metabolites ethyl glucuronide (EtG) and ethyl sulphate (EtS) which confirmed prior drinking, but also tested positive for the fermenting yeast Candida albicans which suggested post-sampling ethanol formation. This and other questionable cases prompted investigation of the suitability of urine alcohol testing for the intended application. Besides the routine measurements of ethanol, illicit drugs and creatinine, randomly selected ethanol-positive and ethanol-negative urines collected within the maritime programme were checked for the presence of EtG and EtS and for fungal and bacterial growth. Data on sample handling and storage was also gathered. Ten of 15 (67%) ethanol-positive and 4 of 9 (44%) ethanol-negative urines contained yeast and/or bacteria. Among the ethanol-positive cases, 4 (27%) were obviously false positives because EtG and EtS were not detected. Microbial action as the reason for false-high ethanol concentrations was indicated in other cases. When 17 bacteria-infected but fungi-negative urines were supplemented with glucose and stored for 1 week at 21 degrees C, ethanol was formed in 2 specimens containing Escherichia coli and E. coli plus P. aeruginosa. In these samples, EtG was also formed on storage while EtS was not. The routines employed for urine collection and handling within this substance abuse programme caused many false-positive identifications of alcohol use with unintended medico-legal consequences. Unpreserved urines stored without cooling should not be used for alcohol testing, given the high risk for microbial interference.

  6. A West Valley Demonstration Project Milestone - Achieving Certification to Ship Waste to the Nevada Test Site

    Jackson, J. P.; Pastor, R. S.

    2002-01-01

    The West Valley Demonstration Project (WVDP) has successfully pretreated and vitrified nearly all of the 600,000 gallons of liquid high-level radioactive waste that was generated at the site of the only commercial nuclear fuel reprocessing plant to have operated in the United States. Low-level waste (LLW) generated during the course of the cleanup effort now requires disposal. Currently the WVDP only ships Class A LLW for off-site disposal. It has been shipping Class A wastes to Envirocare of Utah, Inc. since 1997. However, the WVDP may also have a future need to ship Class B and Class C waste, which Envirocare is not currently authorized to accept. The Nevada Test Site (NTS), a U.S. Department of Energy (DOE) facility, can accept all three waste classifications. The WVDP set a goal to receive certification to begin shipping Class A wastes to NTS by 2001. Formal certification/approval was granted by the DOE Nevada Operations Office on July 12, 2001. This paper discusses how the WVDP contractor, West Valley Nuclear Services Company (WVNSCO), completed the activities required to achieve NTS certification in 2001 to ship waste to its facility. The information and lessons learned provided are significant because the WVDP is the only new generator receiving certification based on an NTS audit in January 2001 that resulted in no findings and only two observations--a rating that is unparalleled in the DOE Complex

  7. Hybrid propulsion testing using direct-drive electrical machines for super yacht and inland shipping

    Paulides, J.J.H.; Djukic, N.; de Roon, J.A.; Encica, L.

    2016-01-01

    Hybrid or full electric propulsions for inland ships are becoming more popular. In these application, direct-drive PM propulsion motors are a preferred machine configuration. This paper discusses the challenges to determine the losses, as estimated with simulations, during the testing procedures of

  8. Physical test report to drop test of a 9975 radioactive material shipping packaging

    Blanton, P.S.

    1997-01-01

    This report presents the drop test results for the 9975 radioactive material shipping package being dropped 30 feet onto a unyielding surface followed by a 40-inch puncture pin drop. The purpose of these drops was to show that the package lid would remain attached to the drum. The 30-foot drop was designed to weaken the lid closure lug while still maintaining maximum extension of the lugs from the drum surface. This was accomplished by angling the drum approximately 30 degrees from horizontal in an inverted position. In this position, the drum was rotated slightly so as not to embed the closure lugs into the drum as a result of the 30-foot drop. It was determined that this orientation would maximize deformation to the closure ring around the closure lug while still maintaining the extension of the lugs from the package surface. The second drop was from 40 inches above a 40-inch tall 6-inch diameter puncture pin. The package was angled 10 degrees from vertical and aligned over the puncture pin to solidly hit the drum lug(s) in an attempt to disengage the lid when dropped.Tests were performed in response to DOE EM-76 review Q5 inquires that questioned the capability of the 9975 drum lid to remain in place under this test sequence. Two packages were dropped utilizing this sequence, a 9974 and 9975. Test results for the 9974 package are reported in WSRC-RP-97-00945. A series of 40-inch puncture pin tests were also performed on undamaged 9975 and 9974 packages

  9. A Base Integer Programming Model and Benchmark Suite for Liner-Shipping Network Design

    Brouer, Berit Dangaard; Alvarez, Fernando; Plum, Christian Edinger Munk

    2014-01-01

    . The potential for making cost-effective and energy-efficient liner-shipping networks using operations research (OR) is huge and neglected. The implementation of logistic planning tools based upon OR has enhanced performance of airlines, railways, and general transportation companies, but within the field......The liner-shipping network design problem is to create a set of nonsimple cyclic sailing routes for a designated fleet of container vessels that jointly transports multiple commodities. The objective is to maximize the revenue of cargo transport while minimizing the costs of operation...... sources of liner shipping for OR researchers in general. We describe and analyze the liner-shipping domain applied to network design and present a rich integer programming model based on services that constitute the fixed schedule of a liner shipping company. We prove the liner-shipping network design...

  10. Ship speed optimization: Concepts, models and combined speed-routing scenarios

    Psaraftis, Harilaos N.; Kontovas, Christos A.

    2014-01-01

    The purpose of this paper is to clarify some important issues as regards ship speed optimization at the operational level and develop models that optimize ship speed for a spectrum of routing scenarios in a single ship setting. The paper's main contribution is the incorporation of those fundament...... parameters and other considerations that weigh heavily in a ship owner's or charterer's speed decision and in his routing decision, wherever relevant. Various examples are given so as to illustrate the properties of the optimal solution and the various trade-offs that are involved....

  11. Modal test results of a ship under operational conditions

    Orlowitz, Esben; Brandt, Anders

    2014-01-01

    Skibe er udsat for et komplekst vibration miljø, påvirket af havet, samt driftsforholdene. Især er det vanskeligt at anslå analytisk værdier for de hydrodynamiske påvirkninger. Eksperimentelle resultater er derfor vigtigt for at kontrollere de analytiske modeller. I den foreliggende artikel præse...... fokuserer på driftsforhold påvirkning af de modal parametre og viser en betydelig variation af modal dæmpning af skibet i drift, med cirka 400%, 200% og 400% forskel i de første tre globale lodrette bøjning modes, ved forskellige operations hastigheder....

  12. Experimental and theoretical study of magnetohydrodynamic ship models.

    David Cébron

    Full Text Available Magnetohydrodynamic (MHD ships represent a clear demonstration of the Lorentz force in fluids, which explains the number of students practicals or exercises described on the web. However, the related literature is rather specific and no complete comparison between theory and typical small scale experiments is currently available. This work provides, in a self-consistent framework, a detailed presentation of the relevant theoretical equations for small MHD ships and experimental measurements for future benchmarks. Theoretical results of the literature are adapted to these simple battery/magnets powered ships moving on salt water. Comparison between theory and experiments are performed to validate each theoretical step such as the Tafel and the Kohlrausch laws, or the predicted ship speed. A successful agreement is obtained without any adjustable parameter. Finally, based on these results, an optimal design is then deduced from the theory. Therefore this work provides a solid theoretical and experimental ground for small scale MHD ships, by presenting in detail several approximations and how they affect the boat efficiency. Moreover, the theory is general enough to be adapted to other contexts, such as large scale ships or industrial flow measurement techniques.

  13. Experimental and theoretical study of magnetohydrodynamic ship models.

    Cébron, David; Viroulet, Sylvain; Vidal, Jérémie; Masson, Jean-Paul; Viroulet, Philippe

    2017-01-01

    Magnetohydrodynamic (MHD) ships represent a clear demonstration of the Lorentz force in fluids, which explains the number of students practicals or exercises described on the web. However, the related literature is rather specific and no complete comparison between theory and typical small scale experiments is currently available. This work provides, in a self-consistent framework, a detailed presentation of the relevant theoretical equations for small MHD ships and experimental measurements for future benchmarks. Theoretical results of the literature are adapted to these simple battery/magnets powered ships moving on salt water. Comparison between theory and experiments are performed to validate each theoretical step such as the Tafel and the Kohlrausch laws, or the predicted ship speed. A successful agreement is obtained without any adjustable parameter. Finally, based on these results, an optimal design is then deduced from the theory. Therefore this work provides a solid theoretical and experimental ground for small scale MHD ships, by presenting in detail several approximations and how they affect the boat efficiency. Moreover, the theory is general enough to be adapted to other contexts, such as large scale ships or industrial flow measurement techniques.

  14. Oceanographic data collected during the EX1401 (Ship Shakedown and Patch Test Exploration) expedition on NOAA Ship OKEANOS EXPLORER in the North Atlantic Ocean from 2014-02-06 to 2014-02-09 (NODC Accession 0116846)

    National Oceanic and Atmospheric Administration, Department of Commerce — To begin the 2014 NOAA Ship Okeanos Explorer field season, a ship shakedown and multibeam patch test was performed off the coast of Rhode Island over Veatch Canyon....

  15. Performance Monitoring of Ships

    Hansen, Søren Vinther

    is used as input to the system and by comparing model and ship behaviour, an index describing the ship’s performance is generated. The work in this thesis is based on data logged through the automation system on board a PostPanmax container ship where data have been logged through a year. A routine...... in the models have been identified. The models used in this work are based on empirical relations or based on regression analyses of model tests and full-scale trials. In order to achieve valid results the conditions where performance is estimated have to be inside the boundaries of the model. Filters have been......The purpose of the research project is to establish a reliable index in the performance evaluation of ships. During operation the ship will experience added resistance due to fouling of hull and propeller. The added resistance will lead to increased fuel consumption and thus increased emissions...

  16. Modeling of Ship Collision Risk Index Based on Complex Plane and Its Realization

    Xiaoqin Xu

    2016-07-01

    Full Text Available Ship collision risk index is the basic and important concept in the domain of ship collision avoidance. In this paper, the advantages and deficiencies of the various calculation methods of ship collision risk index are pointed out. Then the ship collision risk model based on complex plane, which can well make up for the deficiencies of the widely-used evaluation model proposed by Kearon.J and Liu ruru is proposed. On this basis, the calculation method of collision risk index under the encountering situation of multi-ships is constructed, then the three-dimensional image and spatial curve of the risk index are figured out. Finally, single chip microcomputer is used to realize the model. And attaching this single chip microcomputer to ARPA is helpful to the decision-making of the marine navigators.

  17. Marine traffic model based on cellular automaton: Considering the change of the ship's velocity under the influence of the weather and sea

    Qi, Le; Zheng, Zhongyi; Gang, Longhui

    2017-10-01

    It was found that the ships' velocity change, which is impacted by the weather and sea, e.g., wind, sea wave, sea current, tide, etc., is significant and must be considered in the marine traffic model. Therefore, a new marine traffic model based on cellular automaton (CA) was proposed in this paper. The characteristics of the ship's velocity change are taken into account in the model. First, the acceleration of a ship was divided into two components: regular component and random component. Second, the mathematical functions and statistical distribution parameters of the two components were confirmed by spectral analysis, curve fitting and auto-correlation analysis methods. Third, by combining the two components, the acceleration was regenerated in the update rules for ships' movement. To test the performance of the model, the ship traffic flows in the Dover Strait, the Changshan Channel and the Qiongzhou Strait were studied and simulated. The results show that the characteristics of ships' velocities in the simulations are consistent with the measured data by Automatic Identification System (AIS). Although the characteristics of the traffic flow in different areas are different, the velocities of ships can be simulated correctly. It proves that the velocities of ships under the influence of weather and sea can be simulated successfully using the proposed model.

  18. Developmental testing of partially volatile neutron shields for high-performance shipping casks

    Pope, R.B.; Allen, G.C.; Rack, H.J.; Joseph, B.J.; Dupree, S.A.

    1980-01-01

    Results of the phase one tests have demonstrated that the neutron-shielding concept described in this paper is a viable design option for spent fuel shipping casks. The tests have shown that the Boro-silicone 236 shield is superior to the other shield materials considered. Repeated TGA, aging and fire tests demonstrated the reliability of the data. A second phase of the test program is now being pursued where the Boro-silicone 236 is injected into all-steel slab sections, and cured in place. 5 tables

  19. Development of methodology for certification of Type B shipping containers using analytical and testing techniques

    Sharp, R.R.; Varley, D.T.

    1992-01-01

    The Analysis and Testing Group (WX-11) of the Design Engineering Division at Los Alamos National Laboratory (LANL) is developing methodology for designing and providing a basis for certification of Type B shipping containers. This methodology will include design, analysis, testing, fabrication, procurement, and obtaining certification of the Type B containers, allowing usage in support of the United States Department of Energy programs. While all aspects of the packaging development are included in this methodology, this paper focuses on the use of analysis and testing techniques for enhancing the design and providing a basis for certification. This methodology is based on concurrent engineering principles. Multidisciplinary teams within LANL are responsible for the design and certification of specific Type B Radioactive Material Shipping Containers. These teams include personnel with the various backgrounds and areas of expertise required to support the design, testing, analysis and certification tasks. To demonstrate that a package can pass all the performance requirements, the design needs to be characterized as completely as possible. Understanding package responses to the various environments and how these responses influence the effectiveness of the packaging requires expertise in several disciplines. In addition to characterizing the shipping container designs, these multidisciplinary teams should be able to provide insight into improving new package designs

  20. Documentation for first annual testing and inspections of Benificial Uses Shipping System (BUSS) Cask

    Lundeen, J.E.

    1994-01-01

    The purpose of this report is to compile date generated during the first annual tests and inspections of the Benificiai Uses Shipping System (BUSS) Cask. In addition, this report will verify that the testing criteria identified in chapter 8 of the BUSS Cask Safety Analysis Report for Packaging (SARP) was met. Section 8.2 ''Maintenance and Periodic Inspection Program'' of the BUSS Cask SARP requires that the following tests and inspections be performed on an annual basis: Hydrostatic pressure test; helium leak test; dye penetrant test on the trunnions and lifting lugs; and torque test on all bolts; impact limiter inspection and weight test. The first annual inspections and testing of the BUSS Cask were completed on May 5, 1994, and met the SARP criteria

  1. DETERMINATION OF RELEVANT FEATURES OF A SCALE MODEL FOR A 55 000 DWT BULK CARRIER NECESSARY TO STUDY THE SHIP MANEUVERABILITY

    ALECU TOMA

    2016-06-01

    Full Text Available The study method of a ship behavior based on practical tests on scale models is widely used both leading scientists and engineers, architects and researchers in the naval field. In this paper we propose to determine the parameters of a ship handling characteristics relevant to study the 55,000 dwt bulk carrier using a scale model. Scientific background for practical experimentation of this techniques necessary to built a scale model ship consists in applying the principles of similarity or "similitude". The scale model achieved by applying the laws of similarity must allow, through approximations available in certain circumstances, finding relevant parameters needed to simplify and solve the Navier-Stokes equations. These parameters are necessary for modeling the interaction between hull of the real ship and the fluid motion.

  2. SAVIT: a dymanic model to predict vibratory motion within a spent fuel shipping cask; rail car system

    Fields, S.R.

    1978-03-01

    A dynamic model of a spent fuel shipping cask-rail car system has been developed to provide estimates of the vibratory motion of LWR spent fuel assemblies during transport and to estimate the effects of this motion on the condition of the assemblies when they arrive at receiving and storage facilities. Results of preliminary test computations are presented to illustrate the capabilities of the model

  3. A novel flexible model for piracy and robbery assessment of merchant ship operations

    Pristrom, Sascha; Yang, Zaili; Wang, Jin; Yan, Xinping

    2016-01-01

    Maritime piracy and robbery can not only cause logistics chain disruption leading to economic consequences but also result in loss of lives, and short- and long-term health problems of seafarers and passengers. There is a justified need for further investigation in this area of paramount importance. This study analyses maritime piracy and robbery related incidents in terms of the major influencing factors such as ship characteristics and geographical locations. An analytical model incorporating Bayesian reasoning is proposed to estimate the likelihood of a ship being hijacked in the Western Indian or Eastern African region. The proposed model takes into account the characteristics of the ship, environment conditions and the maritime security measures in place in an integrated manner. Available data collected from the Global Integrated Shipping Information System (GISIS) together with expert judgement is used to develop and demonstrate the proposed model. This model can be used by maritime stakeholders to make cost-effective anti-piracy decisions in their operations under uncertainties. Discussions are given on industrial response to maritime piracy in order to minimize the risk to ships exposed to attacks from pirates. Further recommendations on how maritime security and piracy may be best addressed in terms of maritime security measures are outlined. - Highlights: • Analysis of maritime piracy and robbery related incidents in terms of the major influencing factors such as ship characteristics. • Development of an analytical model for estimating the likelihood of a ship being hijacked in the Western Indian or Eastern African region. • Demonstration of the proposed model using data collected from the Global Integrated Shipping Information System (GISIS) together with expert judgement. • Development of an analytical model for maritime piracy and robbery assessment.

  4. An Optimization Model For Strategy Decision Support to Select Kind of CPO’s Ship

    Suaibah Nst, Siti; Nababan, Esther; Mawengkang, Herman

    2018-01-01

    The selection of marine transport for the distribution of crude palm oil (CPO) is one of strategy that can be considered in reducing cost of transport. The cost of CPO’s transport from one area to CPO’s factory located at the port of destination may affect the level of CPO’s prices and the number of demands. In order to maintain the availability of CPO a strategy is required to minimize the cost of transporting. In this study, the strategy used to select kind of charter ships as barge or chemical tanker. This study aims to determine an optimization model for strategy decision support in selecting kind of CPO’s ship by minimizing costs of transport. The select of ship was done randomly, so that two-stage stochastic programming model was used to select the kind of ship. Model can help decision makers to select either barge or chemical tanker to distribute CPO.

  5. Resistance test of high-speed ship by means of attitude control method. Part 2; Shisei seigyo hoshiki ni yoru kosokutei no teiko shiken. 2

    Hayashida, S [Nagasaki Institute of Applied Science, Nagasaki (Japan)

    1996-04-10

    The previous paper has proposed a resistance test method by controlling the attitude of a high-speed model ship using a personal computer without making a data base. For this method, the fluid force acting on the hull of model ship is measured, to change its attitude based on the measurement, and then, the fluid force is measured again, to change the attitude again. The traveling attitude is created by repeating this, to measure the force acting on the hull. Since the attitude is changed by calculating using the fluid force measured, various factors can be considered in the calculation process. For example, a test with an arbitrary displacement in an arbitrary position of center of gravity can be conducted in spite of actual displacement and position of center of gravity of the model ship. A test for a high-speed ship was conducted through this method, to obtain nearly satisfactory results compared with a usual resistance test. Occasionally, a lot of repetitions were required to satisfy the balancing condition of the force. In this study, the improvement of testing efficiency has been planned by modifying the analyzing program. 5 refs., 7 figs., 1 tab.

  6. A Ship Propulsion System Model for Fault-tolerant Control

    Izadi-Zamanabadi, Roozbeh; Blanke, M.

    This report presents a propulsion system model for a low speed marine vehicle, which can be used as a test benchmark for Fault-Tolerant Control purposes. The benchmark serves the purpose of offering realistic and challenging problems relevant in both FDI and (autonomous) supervisory control area...

  7. Destructive Testing of an ES-3100 Shipping Container at the Savannah River National Laboratory

    Loftin, B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Abramczyk, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-06-09

    Destructive testing of an ES-3100 Shipping Container was completed by the Packaging Technology and Pressurized Systems organization within the Savannah River National Laboratory in order to qualify the ES-3100 as a candidate storage and transport package for applications at various facilities at the Savannah River Site. The testing consisted of the detonation of three explosive charges at separate locations on a single ES-3100. The locations for the placement were chosen based the design of the ES-3100 as well as the most likely places for the package to incur damage as a result of the detonation. The testing was completed at an offsite location, which raised challenges as well as allowed for development of new partnerships for this testing and for potential future testing. The results of the testing, the methods used to complete the testing, and similar, potential future work will be discussed.

  8. Decision Making Model for Ro-Ro Short Sea Shipping Operations in Archipelagic Southeast Asia

    Aminuddin Md Arof

    2018-03-01

    Full Text Available This study aims to develop a decision-making model for determining the potential of interstate Ro-Ro Short Sea Shipping (SSS operations in Archipelagic Southeast Asia (ASEA. It is expected to assist SSS authorities, private investors and financial institutions focus their limited resources on several key factors that could ensure the success of their undertakings. This study will begin with identifying the relevant factors that have contributed towards successful SSS operations through a process of literature review. Subsequently, a Delphi survey was conducted with sub-regional experts to identify any new determinants and assess their opinions on the relative importance of all the determinants involved. Finally the weightages of the determinants were ascertained through the Analytic Hierarchy Process (AHP. Twenty expert respondents from Brunei Darussalam. Indonesia, Malaysia and the Philippines were involved in the Delphi survey while 18 expert respondents continue to participate in the AHP survey. This study concludes with the development of a decision-making model that was tested on three interstate Ro-Ro SSS routes within the ASEA sub-region. Keywords: Archipelagic Southeast Asia, Analytic Hierarchy Process (AHP, ASEAN, Delphi, Ro-Ro, Short Sea Shipping (SSS

  9. Results of the power-up test of the nuclear-powered ship MUTSU and test programs of her experimental voyages

    Ochiai, Masa-aki; Ishida, Toshihisa; Itagaki, Masafumi; Sakamoto, Yukio; Kyouya, Masahiko

    1991-01-01

    The power-up test of N.S. MUTSU was performed successfully almost on schedule in spite of minor troubles resolved in a short time, and the results of various areas were satisfactory. The official sea trial was well carried out. Then, the ship was officially designated the first nuclear ship in Japan. Experimental voyages are to be performed to yield profitable data for further research on nuclear ships in the future. (author)

  10. An integer programming model and benchmark suite for liner shipping network design

    Løfstedt, Berit; Alvarez, Jose Fernando; Plum, Christian Edinger Munk

    effective and energy efficient liner shipping networks using operations research is huge and neglected. The implementation of logistic planning tools based upon operations research has enhanced performance of both airlines, railways and general transportation companies, but within the field of liner......Maritime transportation is accountable for 2.7% of the worlds CO2 emissions and the liner shipping industry is committed to a slow steaming policy to provide low cost and environmentally conscious global transport of goods without compromising the level of service. The potential for making cost...... along with a rich integer programming model based on the services, that constitute the fixed schedule of a liner shipping company. The model may be relaxed as well as decomposed. The design of a benchmark suite of data instances to reflect the business structure of a global liner shipping network...

  11. An Enterprise Model of Rising Ship Costs: Loss of Learning Due to Time between Ships and Labor Force Instability

    Summerville, Jessica R.; Cullis, Bethia L.; Druker, Eric R.; Rutledge, Gabriel B.; Braxton, Peter J.; Coleman, Richard L.

    2007-01-01

    Proceedings Paper (for Acquisition Research Program) Since the end of the Cold War, the perceived need for Navy ships has dropped, and so the shipbuilding budget has dropped. Seemingly coincidental with this budgetary pressure, and perversely aggravating the problem, ship costs began to rise steeply. We will set aside that ships have grown in weight by about three percent per year since World War II and that ever-more weapon systems are being put into them, and confine ourselves to discu...

  12. Field test of available methods to measure remotely SOx and NOx emissions from ships

    Balzani Lööv, J. M.; Alfoldy, B.; Gast, L. F. L.; Hjorth, J.; Lagler, F.; Mellqvist, J.; Beecken, J.; Berg, N.; Duyzer, J.; Westrate, H.; Swart, D. P. J.; Berkhout, A. J. C.; Jalkanen, J.-P.; Prata, A. J.; van der Hoff, G. R.; Borowiak, A.

    2014-08-01

    Methods for the determination of ship fuel sulphur content and NOx emission factors based on remote measurements have been compared in the harbour of Rotterdam and compared to direct stack emission measurements on the ferry Stena Hollandica. The methods were selected based on a review of the available literature on ship emission measurements. They were either optical (LIDAR, Differential Optical Absorption Spectroscopy (DOAS), UV camera), combined with model-based estimates of fuel consumption, or based on the so called "sniffer" principle, where SO2 or NOx emission factors are determined from simultaneous measurement of the increase of CO2 and SO2 or NOx concentrations in the plume of the ship compared to the background. The measurements were performed from stations at land, from a boat and from a helicopter. Mobile measurement platforms were found to have important advantages compared to the land-based ones because they allow optimizing the sampling conditions and sampling from ships on the open sea. Although optical methods can provide reliable results it was found that at the state of the art level, the "sniffer" approach is the most convenient technique for determining both SO2 and NOx emission factors remotely. The average random error on the determination of SO2 emission factors comparing two identical instrumental set-ups was 6%. However, it was found that apparently minor differences in the instrumental characteristics, such as response time, could cause significant differences between the emission factors determined. Direct stack measurements showed that about 14% of the fuel sulphur content was not emitted as SO2. This was supported by the remote measurements and is in agreement with the results of other field studies.

  13. Field test of available methods to measure remotely SO2 and NOx emissions from ships

    Balzani Lööv, J. M.; Alfoldy, B.; Beecken, J.; Berg, N.; Berkhout, A. J. C.; Duyzer, J.; Gast, L. F. L.; Hjorth, J.; Jalkanen, J.-P.; Lagler, F.; Mellqvist, J.; Prata, F.; van der Hoff, G. R.; Westrate, H.; Swart, D. P. J.; Borowiak, A.

    2013-11-01

    Methods for the determination of ship fuel sulphur content and NOx emission factors from remote measurements have been compared in the harbour of Rotterdam and compared to direct stack emission measurements on the ferry Stena Hollandica. The methods were selected based on a review of the available literature on ship emission measurements. They were either optical (LIDAR, DOAS, UV camera), combined with model based estimates of fuel consumption, or based on the so called "sniffer" principle, where SO2 or NOx emission factors are determined from simultaneous measurement of the increase of CO2 and SO2 or NOx concentrations in the plume of the ship compared to the background. The measurements were performed from stations at land, from a boat, and from a helicopter. Mobile measurement platforms were found to have important advantages compared to the landbased ones because they allow to optimize the sampling conditions and to sample from ships on the open sea. Although optical methods can provide reliable results, it was found that at the state of the art, the "sniffer" approach is the most convenient technique for determining both SO2 and NOx emission factors remotely. The average random error on the determination of SO2 emission factors comparing two identical instrumental set-ups was 6%. However, it was found that apparently minor differences in the instrumental characteristics, such as response time, could cause significant differences between the emission factors determined. Direct stack measurements showed that about 14% of the fuel sulphur content was not emitted as SO2. This was supported by the remote measurements and is in agreement with the results of other field studies.

  14. Tramp Ship Routing and Scheduling - Models, Methods and Opportunities

    Vilhelmsen, Charlotte; Larsen, Jesper; Lusby, Richard Martin

    of their demand in advance. However, the detailed requirements of these contract cargoes can be subject to ongoing changes, e.g. the destination port can be altered. For tramp operators, a main concern is therefore the efficient and continuous planning of routes and schedules for the individual ships. Due...... and scheduling problem, focus should now be on extending this basic problem to include additional real-world complexities and develop suitable solution methods for those extensions. Such extensions will enable more tramp operators to benefit from the solution methods while simultaneously creating new...

  15. Modeling the regional impact of ship emissions on NOx and ozone levels over the Eastern Atlantic and Western Europe using ship plume parameterization

    P. Pisoft

    2010-07-01

    Full Text Available In general, regional and global chemistry transport models apply instantaneous mixing of emissions into the model's finest resolved scale. In case of a concentrated source, this could result in erroneous calculation of the evolution of both primary and secondary chemical species. Several studies discussed this issue in connection with emissions from ships and aircraft. In this study, we present an approach to deal with the non-linear effects during dispersion of NOx emissions from ships. It represents an adaptation of the original approach developed for aircraft NOx emissions, which uses an exhaust tracer to trace the amount of the emitted species in the plume and applies an effective reaction rate for the ozone production/destruction during the plume's dilution into the background air. In accordance with previous studies examining the impact of international shipping on the composition of the troposphere, we found that the contribution of ship induced surface NOx to the total reaches 90% over remote ocean and makes 10–30% near coastal regions. Due to ship emissions, surface ozone increases by up to 4–6 ppbv making 10% contribution to the surface ozone budget. When applying the ship plume parameterization, we show that the large scale NOx decreases and the ship NOx contribution is reduced by up to 20–25%. A similar decrease was found in the case of O3. The plume parameterization suppressed the ship induced ozone production by 15–30% over large areas of the studied region. To evaluate the presented parameterization, nitrogen monoxide measurements over the English Channel were compared with modeled values and it was found that after activating the parameterization the model accuracy increases.

  16. Comparison of elastic and inelastic analysis and test results for the defense high level waste shipping cask

    Zimmer, A.; Koploy, M.A.; Madsen, M.M.

    1991-01-01

    In the early 1980s, the US DOE/Defense Programs (DOE/DP) initiated a project to develop a safe and efficient transportation system for defense high level waste (DHLW). A long-standing objective of the DHLW transportation project is to develop a truck cask that represents the leading edge of cask technology as well as fully complies with all applicable DOE, Nuclear Regulatory Commission, and DOT regulations. General Atomics designed the DHLW Truck Shipping Cask using state-of-the-art analytical techniques verified by model testing performed by Sandia National Labs. (SNL). The analytical techniques include two approaches, inelastic analysis and elastic analysis. This paper will compare the results of the two analytical approaches and with model testing results. The purpose of this work is to provide data to support licensing of the DHLW cask and to support the acceptance by the NRC of inelastic analysis as a tool in packaging design and licensing

  17. Prevention of oil spill from shipping by modelling of dynamic risk.

    Eide, Magnus S; Endresen, Oyvind; Breivik, Oyvind; Brude, Odd Willy; Ellingsen, Ingrid H; Røang, Kjell; Hauge, Jarle; Brett, Per Olaf

    2007-10-01

    This paper presents a new dynamic environmental risk model, with intended use within a new, dynamical approach for risk based ship traffic prioritisation. The philosophy behind this newly developed approach is that shipping risk can be reduced by directing efforts towards ships and areas that have been identified as high priority (high risk), prior to a potential accident. The risk model proposed in this paper separates itself from previous models by drawing on available information on dynamic factors and by focusing on the ship's surroundings. The model estimates the environmental risk of drift grounding accidents for oil tankers in real time and in forecast mode, combining the probability of grounding with oil spill impact on the coastline. Results show that the inherent dynamic risk introduced by an oil tanker sailing along the North Norwegian coast depends, not surprisingly, significantly upon wind and ocean currents, as well as tug position and cargo oil type. Results of this study indicate that the risk model is well suited for real time risk assessment, and effectively separates low risk and high risk situations. The model is well suited as a tool to prioritise oil tankers and coastal segments. This enables dynamic risk based positioning of tugs, using both real-time and projected risk, for effective support in case of a drifting ship situation.

  18. FACSIM/MRS [Monitored Retrievable Storage]-2: Storage and shipping model documentation and user's guide

    Huber, H.D.; Chockie, A.D.; Hostick, C.J.; Otis, P.T.; Sovers, R.A.

    1987-06-01

    The Pacific Northwest Laboratory (PNL) has developed a stochastic computer model, FACSIM/MRS, to assist in assessing the operational performance of the Monitored Retrievable Storage (MRS) waste-handling facility. This report provides the documentation and user's guide for FACSIM/MRS-2, which is also referred to as the back-end model. The FACSIM/MRS-2 model simulates the MRS storage and shipping operations, which include handling canistered spent fuel and secondary waste in the shielded canyon cells, in onsite yard storage, and in repository shipping cask loading areas

  19. Full scale test results for ship ice impact forces and pressures

    Ghoneim, G.A.

    1993-01-01

    A set of full scale impact tests were carried out for the icebreakers Canmar Kigoriak and Robert LeMeur in first and multi-year ice conditions in the southern Beaufort Sea. Preliminary results of the testing program were published in Ghoneim et al. (1984). This paper presents some salient results of further analysis of the data. This includes a description of the different types of ice ramming mechanisms and the corresponding ice force time histories and ship response. A comparison between the bow force peak values for the kigoriak and the Robert LeMeur is made and the reasons for the difference are evaluated. The question of dynamic magnification of the response is investigated. The relationship between the peak impact force and the ramming velocity is evaluated for both ships and compared with theoretical and empirical formulations. Other parametric relationships are presented, including such parameters as force duration and relative magnitude of the impact and beaching bow forces. The added mass is evaluated from measured accelerations and calculated bow forces and are shown to be time dependent. The relationship between ice pressure and corresponding contact area is discussed. Finally, conclusions and recommendations are presented

  20. Formal safety assessment based on relative risks model in ship navigation

    Hu Shenping [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: sphu@mmc.shmtu.edu.cn; Fang Quangen [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: qgfang@mmc.shmtu.edu.cn; Xia Haibo [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: hbxia@mmc.shmtu.edu.cn; Xi Yongtao [Merchant Marine College, Shanghai Maritime University, 1550, Pudong Dadao, Shanghai 200135 (China)]. E-mail: xiyt@mmc.shmtu.edu.cn

    2007-03-15

    Formal safety assessment (FSA) is a structured and systematic methodology aiming at enhancing maritime safety. It has been gradually and broadly used in the shipping industry nowadays around the world. On the basis of analysis and conclusion of FSA approach, this paper discusses quantitative risk assessment and generic risk model in FSA, especially frequency and severity criteria in ship navigation. Then it puts forward a new model based on relative risk assessment (MRRA). The model presents a risk-assessment approach based on fuzzy functions and takes five factors into account, including detailed information about accident characteristics. It has already been used for the assessment of pilotage safety in Shanghai harbor, China. Consequently, it can be proved that MRRA is a useful method to solve the problems in the risk assessment of ship navigation safety in practice.

  1. Formal safety assessment based on relative risks model in ship navigation

    Hu Shenping; Fang Quangen; Xia Haibo; Xi Yongtao

    2007-01-01

    Formal safety assessment (FSA) is a structured and systematic methodology aiming at enhancing maritime safety. It has been gradually and broadly used in the shipping industry nowadays around the world. On the basis of analysis and conclusion of FSA approach, this paper discusses quantitative risk assessment and generic risk model in FSA, especially frequency and severity criteria in ship navigation. Then it puts forward a new model based on relative risk assessment (MRRA). The model presents a risk-assessment approach based on fuzzy functions and takes five factors into account, including detailed information about accident characteristics. It has already been used for the assessment of pilotage safety in Shanghai harbor, China. Consequently, it can be proved that MRRA is a useful method to solve the problems in the risk assessment of ship navigation safety in practice

  2. Experimental studies of dynamic impact response with scale models of lead shielded radioactive material shipping containers

    Robinson, R.A.; Hadden, J.A.; Basham, S.J.

    1978-01-01

    Preliminary experimental studies of dynamic impact response of scale models of lead-shielded radioactive material shipping containers are presented. The objective of these studies is to provide DOE/ECT with a data base to allow the prediction of a rational margin of confidence in overviewing and assessing the adequacy of the safety and environmental control provided by these shipping containers. Replica scale modeling techniques were employed to predict full scale response with 1/8, 1/4, and 1/2 scale models of shipping containers that are used in the shipment of spent nuclear fuel and high level wastes. Free fall impact experiments are described for scale models of plain cylindrical stainless steel shells, stainless steel shells filled with lead, and replica scale models of radioactive material shipping containers. Dynamic induced strain and acceleration measurements were obtained at several critical locations on the models. The models were dropped from various heights, attitudes to the impact surface, with and without impact limiters and at uniform temperatures between -40 and 175 0 C. In addition, thermal expansion and thermal gradient induced strains were measured at -40 and 175 0 C. The frequency content of the strain signals and the effect of different drop pad compositions and stiffness were examined. Appropriate scale modeling laws were developed and scaling techniques were substantiated for predicting full scale response by comparison of dynamic strain data for 1/8, 1/4, and 1/2 scale models with stainless steel shells and lead shielding

  3. EMP coupling to ships

    Deadrick, F.J.; Cabayan, H.S.; Kunz, K.F.; Bevensee, R.M.; Martin, L.C.; Egbert, R.W.

    1980-01-01

    Scale-model tests were conducted to establish the adequacy and limitations of model measurements as tools for predicting electromagnetic pulse (EMP) coupling voltages and currents to the critical antennas, cables, and metallic structures on ships. The scale-model predictions are compared with the results of the full-scale EMP simulation test of the Canadian ASW ship, HMCS Huron. (The EMP coupling predictions in this report were made without prior knowledge of the results of the data from the HMCS Huron tests.) This report establishes that the scale-model tests in conjunction with the data base from EMP coupling modules provides the necessary information for source model development and permits effective, low-cost study of particular system configurations. 184 figures, 9 tables

  4. An Evacuation Model for Passenger Ships That Includes the Influence of Obstacles in Cabins

    Baocheng Ni

    2017-01-01

    Full Text Available Passenger behavior and ship environment are the key factors affecting evacuation efficiency. However, current studies ignore the interior layout of passenger ship cabins and treat the cabins as empty rooms. To investigate the influence of obstacles (e.g., tables and stools on cabin evacuation, we propose an agent-based social force model for advanced evacuation analysis of passenger ships; this model uses a goal-driven submodel to determine a plan and an extended social force submodel to govern the movement of passengers. The extended social force submodel considers the interaction forces between the passengers, crew, and obstacles and minimises the range of these forces to improve computational efficiency. We drew the following conclusions based on a series of evacuation simulations conducted in this study: (1 the proposed model endows the passenger with the behaviors of bypassing and crossing obstacles, (2 funnel-shaped exits from cabins can improve evacuation efficiency, and (3 as the exit angle increases, the evacuation time also increases. These findings offer ship designers some insight towards increasing the safety of large passenger ships.

  5. Turbulence modeling of transverse flow on ship hulls in shallow water

    Jakobsen, Ken-Robert Gjelstad

    2010-09-15

    The hydrodynamic forces acting on a ship that travels in restricted water vary greatly with water depth and the geometry of the ship hull. This will affect the ship maneuverability in terms of various flow effects like for instance squat, when the ship is sucked down towards the seabed due to a pressure drop on the hull at forward speed. It is, thus, important to gain detailed knowledge on these aspects of marine engineering. The problem is in the present work addressed through a numerical investigation of turbulent transverse flow on two-dimensional ship sections in shallow water. The numerical code is validated against traditional flow problems in the literature. Namely, the Backward-facing step (BFS) and the Smoothly-contoured ramp (SCR). 2D and 3D laminar flows and 2D low Reynolds number turbulent flows are calculated, and the results are found to be in good agreement with the previous numerical and experimental comparison data. The turbulence model used in the calculations is the one-equation Spalart-Allmaras model. The overall goal of achieving more efficient and accurate numerical schemes will always be in focus of code development. Adaptive mesh refinement (AMR) is then a very helpful tool to save both time for grid generation prior to the calculations in question and the CPU hours needed to solve the governing equations. The latter is even more evident in a parallel environment. These aspects are included in the present investigation as part of the process to adapt and investigate a CFD tool suitable to handle turbulent flows on a ship hull in shallow water. Several physical and numerical parameters are included in the present study and the Plackett-Burman screening design is utilized to efficiently analyze the results. With the latter method, a simple function for calculating the drag force on a two-dimensional ship section as function of the given parameters has been obtained. (Author)

  6. Ecological evaluation of proposed dredged material from the John F. Baldwin Ship Channel: Phase 3 -- biological testing

    Kohn, N.P.; Karle, L.M.; Pinza, M.R.; Mayhew, H.L.; White, P.J.; Gruendell, B.D.; Word, J.Q. [Battelle/Marine Sciences Lab., Sequim, WA (United States)

    1993-10-01

    The John F. Baldwin Ship Channel is a 28-mile-long portion of the San Francisco Bay to Stockton Ship Channel, the primary shipping lane through San Francisco Bay and Delta. The San Francisco District of the US Army Corps of Engineers (USACE) is responsible for construction of the John F. Baldwin Ship Channel, which is authorized to be deepened to a project depth of {minus}45 ft relative to mean lower low water (MLLW). Approximately 8.5 million cubic yards (mcy) of sediment will be removed from the channel to reach this project depth. The USACE requested Battelle/Marine Sciences Laboratory (MSL) to conduct testing for ocean disposal under the guidelines in Evaluation of Dredged Material Proposed for Ocean Disposal-Testing Manual (EPA/USACE 1991). This testing manual contains a tiered evaluation approach developed specifically for ocean disposal of dredged material at a selected site. In this study, John F. Baldwin Ship Channel sediments were evaluated under the Tier III (biological) testing guidance, which is considered to be highly stringent and protective of the environment. The Tier III guidance for ocean disposal testing requires tests of water column effects, (following dredged material disposal), deposited sediment toxicity, and bioaccumulation of contaminants from deposited sediment (dredged material).

  7. Incorporation of human factors into ship collision risk models focusing on human centred design aspects

    Sotiralis, P.; Ventikos, N.P.; Hamann, R.; Golyshev, P.; Teixeira, A.P.

    2016-01-01

    This paper presents an approach that more adequately incorporates human factor considerations into quantitative risk analysis of ship operation. The focus is on the collision accident category, which is one of the main risk contributors in ship operation. The approach is based on the development of a Bayesian Network (BN) model that integrates elements from the Technique for Retrospective and Predictive Analysis of Cognitive Errors (TRACEr) and focuses on the calculation of the collision accident probability due to human error. The model takes into account the human performance in normal, abnormal and critical operational conditions and implements specific tasks derived from the analysis of the task errors leading to the collision accident category. A sensitivity analysis is performed to identify the most important contributors to human performance and ship collision. Finally, the model developed is applied to assess the collision risk of a feeder operating in Dover strait using the collision probability estimated by the developed BN model and an Event tree model for calculation of human, economic and environmental risks. - Highlights: • A collision risk model for the incorporation of human factors into quantitative risk analysis is proposed. • The model takes into account the human performance in different operational conditions leading to the collision. • The most important contributors to human performance and ship collision are identified. • The model developed is applied to assess the collision risk of a feeder operating in Dover strait.

  8. Design and test of lightweight sandwich T-joint for naval ships

    Toftegaard, H.; Lystrup, Aa.

    2005-01-01

    Within the EUCLID project, 'Survivability, Durability and Performance of Naval Composite Structures', one task is to develop improved fibre composite joints for naval ship super structures. One type of joint in such a super structure is a T-joint between sandwich panels. An existing design consists...... of panels joined by filler and overlaminates of the same thickness as the skin laminates. Various improved T-joints have been designed and investigated. Some with focus on improved strength (survivability), and others with focus on reduced weight. This paper describes the design and test of a sandwich T...... triangles). A method for a finite element (FE) parameter study is developed and used for selection of a promising (strong) configuration of the T-joint. Tensile (pull-out) tests are performed to load the core triangles and filler in tension and the strength and failure mode are compared both with the FE...

  9. Effects of shipping on marine acoustic habitats in Canadian Arctic estimated via probabilistic modeling and mapping.

    Aulanier, Florian; Simard, Yvan; Roy, Nathalie; Gervaise, Cédric; Bandet, Marion

    2017-12-15

    Canadian Arctic and Subarctic regions experience a rapid decrease of sea ice accompanied with increasing shipping traffic. The resulting time-space changes in shipping noise are studied for four key regions of this pristine environment, for 2013 traffic conditions and a hypothetical tenfold traffic increase. A probabilistic modeling and mapping framework, called Ramdam, which integrates the intrinsic variability and uncertainties of shipping noise and its effects on marine habitats, is developed and applied. A substantial transformation of soundscapes is observed in areas where shipping noise changes from present occasional-transient contributor to a dominant noise source. Examination of impacts on low-frequency mammals within ecologically and biologically significant areas reveals that shipping noise has the potential to trigger behavioral responses and masking in the future, although no risk of temporary or permanent hearing threshold shifts is noted. Such probabilistic modeling and mapping is strategic in marine spatial planning of this emerging noise issues. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  10. A Dynamic Model for Roll Motion of Ships Due to Flooding

    Xia, Jinzhu; Jensen, Jørgen Juncher; Pedersen, Preben Terndrup

    1997-01-01

    A dynamic model is presented of the roll motion of damaged RoRo vessels which couples the internal cross-flooding flow and the air action in the equalizing compartment. The cross flooding flow and the air motion are modelled by a modified Bernoulli equation, where artificial damping is introduced...... to avoid modal instability based on the original Bernoulli equation. The fluid action of the flooded water on the ship is expressed by its influence on the moment of inertia of the ship and the heeling moment, which is a couple created by the gravitational force of the flooded water and the change...... of buoyancy of the ship.Two limiting flooding cases are examined in the present analysis: The sudden ingress of a certain amount of water to the damaged compartment with no further water exchange between the sea and the flooded compartment during the roll motion, and the continuous ingress of water through...

  11. A NOVEL NUMERICAL MODEL APPROACH FOR EXAMINING SHIP BERTHING IMPACT ON FLOATING PIERS

    AMIN CHEGENIZADEH

    2015-08-01

    Full Text Available This paper presents the results of an investigation into the impact of ship berthing upon floating piers using highly advanced numerical software Abaqus. The ship and floating piers were modeled as solid bodies. For the first time, the effect of soil on the total energy absorption of the system was considered using both elastic and elastic-perfectly plastic soil models. First the results for the elastic soil model were compared to and verified by the existing literature using a spring soil model.Then a continuum soil model was utilized instead of a spring soil model, with the results showing 27% higher energy absorption compared to the spring model. The investigation also considered a model with soil as an elastic-perfectly plastic material, being more aligned with the soil material’s real behavior. With this model the results produced 1% more energy absorption as the soil did not reach plastic failure.

  12. Ship-Track Models Based on Poisson-Distributed Port-Departure Times

    Heitmeyer, Richard

    2006-01-01

    ... of those ships, and their nominal speeds. The probability law assumes that the ship departure times are Poisson-distributed with a time-varying departure rate and that the ship speeds and ship routes are statistically independent...

  13. Nonlinear Container Ship Model for the Study of Parametric Roll Resonance

    Christian Holden

    2007-10-01

    Full Text Available Parametric roll is a critical phenomenon for ships, whose onset may cause roll oscillations up to +-40 degrees, leading to very dangerous situations and possibly capsizing. Container ships have been shown to be particularly prone to parametric roll resonance when they are sailing in moderate to heavy head seas. A Matlab/Simulink parametric roll benchmark model for a large container ship has been implemented and validated against a wide set of experimental data. The model is a part of a Matlab/Simulink Toolbox (MSS, 2007. The benchmark implements a 3rd-order nonlinear model where the dynamics of roll is strongly coupled with the heave and pitch dynamics. The implemented model has shown good accuracy in predicting the container ship motions, both in the vertical plane and in the transversal one. Parametric roll has been reproduced for all the data sets in which it happened, and the model provides realistic results which are in good agreement with the model tank experiments.

  14. An adaptive grid to improve the efficiency and accuracy of modelling underwater noise from shipping

    Trigg, Leah; Chen, Feng; Shapiro, Georgy; Ingram, Simon; Embling, Clare

    2017-04-01

    Underwater noise from shipping is becoming a significant concern and has been listed as a pollutant under Descriptor 11 of the Marine Strategy Framework Directive. Underwater noise models are an essential tool to assess and predict noise levels for regulatory procedures such as environmental impact assessments and ship noise monitoring. There are generally two approaches to noise modelling. The first is based on simplified energy flux models, assuming either spherical or cylindrical propagation of sound energy. These models are very quick but they ignore important water column and seabed properties, and produce significant errors in the areas subject to temperature stratification (Shapiro et al., 2014). The second type of model (e.g. ray-tracing and parabolic equation) is based on an advanced physical representation of sound propagation. However, these acoustic propagation models are computationally expensive to execute. Shipping noise modelling requires spatial discretization in order to group noise sources together using a grid. A uniform grid size is often selected to achieve either the greatest efficiency (i.e. speed of computations) or the greatest accuracy. In contrast, this work aims to produce efficient and accurate noise level predictions by presenting an adaptive grid where cell size varies with distance from the receiver. The spatial range over which a certain cell size is suitable was determined by calculating the distance from the receiver at which propagation loss becomes uniform across a grid cell. The computational efficiency and accuracy of the resulting adaptive grid was tested by comparing it to uniform 1 km and 5 km grids. These represent an accurate and computationally efficient grid respectively. For a case study of the Celtic Sea, an application of the adaptive grid over an area of 160×160 km reduced the number of model executions required from 25600 for a 1 km grid to 5356 in December and to between 5056 and 13132 in August, which

  15. Mean velocity and moments of turbulent velocity fluctuations in the wake of a model ship propulsor

    Pego, J.P. [Universitaet Erlangen-Nuernberg, LSTM, Erlangen, Lehrstuhl fuer Stroemungsmechanik, Erlangen (Germany); Faculdade de Engenharia da Universidade do Porto, Porto (Portugal); Lienhart, H.; Durst, F. [Universitaet Erlangen-Nuernberg, LSTM, Erlangen, Lehrstuhl fuer Stroemungsmechanik, Erlangen (Germany)

    2007-08-15

    Pod drives are modern outboard ship propulsion systems with a motor encapsulated in a watertight pod, whose shaft is connected directly to one or two propellers. The whole unit hangs from the stern of the ship and rotates azimuthally, thus providing thrust and steering without the need of a rudder. Force/momentum and phase-resolved laser Doppler anemometry (LDA) measurements were performed for in line co-rotating and contra-rotating propellers pod drive models. The measurements permitted to characterize these ship propulsion systems in terms of their hydrodynamic characteristics. The torque delivered to the propellers and the thrust of the system were measured for different operation conditions of the propellers. These measurements lead to the hydrodynamic optimization of the ship propulsion system. The parameters under focus revealed the influence of distance between propeller planes, propeller frequency of rotation ratio and type of propellers (co- or contra-rotating) on the overall efficiency of the system. Two of the ship propulsion systems under consideration were chosen, based on their hydrodynamic characteristics, for a detailed study of the swirling wake flow by means of laser Doppler anemometry. A two-component laser Doppler system was employed for the velocity measurements. A light barrier mounted on the axle of the rear propeller motor supplied a TTL signal to mark the beginning of each period, thus providing angle information for the LDA measurements. Measurements were conducted for four axial positions in the slipstream of the pod drive models. The results show that the wake of contra-rotating propeller is more homogeneous than when they co-rotate. In agreement with the results of the force/momentum measurements and with hypotheses put forward in the literature (see e.g. Poehls in Entwurfsgrundlagen fuer Schraubenpropeller, 1984; Schneekluth in Hydromechanik zum Schiffsentwurf, 1988; Breslin and Andersen in Hydrodynamics of ship propellers, 1996

  16. Mean velocity and moments of turbulent velocity fluctuations in the wake of a model ship propulsor

    Pêgo, J. P.; Lienhart, H.; Durst, F.

    2007-08-01

    Pod drives are modern outboard ship propulsion systems with a motor encapsulated in a watertight pod, whose shaft is connected directly to one or two propellers. The whole unit hangs from the stern of the ship and rotates azimuthally, thus providing thrust and steering without the need of a rudder. Force/momentum and phase-resolved laser Doppler anemometry (LDA) measurements were performed for in line co-rotating and contra-rotating propellers pod drive models. The measurements permitted to characterize these ship propulsion systems in terms of their hydrodynamic characteristics. The torque delivered to the propellers and the thrust of the system were measured for different operation conditions of the propellers. These measurements lead to the hydrodynamic optimization of the ship propulsion system. The parameters under focus revealed the influence of distance between propeller planes, propeller frequency of rotation ratio and type of propellers (co- or contra-rotating) on the overall efficiency of the system. Two of the ship propulsion systems under consideration were chosen, based on their hydrodynamic characteristics, for a detailed study of the swirling wake flow by means of laser Doppler anemometry. A two-component laser Doppler system was employed for the velocity measurements. A light barrier mounted on the axle of the rear propeller motor supplied a TTL signal to mark the beginning of each period, thus providing angle information for the LDA measurements. Measurements were conducted for four axial positions in the slipstream of the pod drive models. The results show that the wake of contra-rotating propeller is more homogeneous than when they co-rotate. In agreement with the results of the force/momentum measurements and with hypotheses put forward in the literature (see e.g. Poehls in Entwurfsgrundlagen für Schraubenpropeller, 1984; Schneekluth in Hydromechanik zum Schiffsentwurf, 1988; Breslin and Andersen in Hydrodynamics of ship propellers, 1996

  17. Remote sensing image ship target detection method based on visual attention model

    Sun, Yuejiao; Lei, Wuhu; Ren, Xiaodong

    2017-11-01

    The traditional methods of detecting ship targets in remote sensing images mostly use sliding window to search the whole image comprehensively. However, the target usually occupies only a small fraction of the image. This method has high computational complexity for large format visible image data. The bottom-up selective attention mechanism can selectively allocate computing resources according to visual stimuli, thus improving the computational efficiency and reducing the difficulty of analysis. Considering of that, a method of ship target detection in remote sensing images based on visual attention model was proposed in this paper. The experimental results show that the proposed method can reduce the computational complexity while improving the detection accuracy, and improve the detection efficiency of ship targets in remote sensing images.

  18. Hydromechanics of Wind-Assisted Ship Propulsion : Modeling of Hydrodynamic Sideforce

    van der Kolk, N.J.

    2016-01-01

    This paper deals with the hydrodynamic sideforce production of a wind-assisted ship. The subject is introduced, both in physical terms, and with an overview of current and recent work. The importance of the hydrodynamic sideforce is established, before classical models are reviewed. Finally, the

  19. Structural modeling and fuzzy-logic based diagnosis of a ship propulsion benchmark

    Izadi-Zamanabadi, Roozbeh; Blanke, M.; Katebi, S.D.

    2000-01-01

    An analysis of structural model of a ship propulsion benchmark leads to identifying the subsystems with inherent redundant information. For a nonlinear part of the system, a Fuzzy logic based FD algorithm with adaptive threshold is employed. The results illustrate the applicability of structural...

  20. Particle-Resolved Modeling of Aerosol Mixing State in an Evolving Ship Plume

    Riemer, N. S.; Tian, J.; Pfaffenberger, L.; Schlager, H.; Petzold, A.

    2011-12-01

    The aerosol mixing state is important since it impacts the particles' optical and CCN properties and thereby their climate impact. It evolves continuously during the particles' residence time in the atmosphere as a result of coagulation with other particles and condensation of secondary aerosol species. This evolution is challenging to represent in traditional aerosol models since they require the representation of a multi-dimensional particle distribution. While modal or sectional aerosol representations cannot practically resolve the aerosol mixing state for more than a few species, particle-resolved models store the composition of many individual aerosol particles directly. They thus sample the high-dimensional composition state space very efficiently and so can deal with tens of species, fully resolving the mixing state. Here we use the capabilities of the particle-resolved model PartMC-MOSAIC to simulate the evolution of particulate matter emitted from marine diesel engines and compare the results to aircraft measurements made in the English Channel in 2007 as part of the European campaign QUANTIFY. The model was initialized with values of gas concentrations and particle size distributions and compositions representing fresh ship emissions. These values were obtained from a test rig study in the European project HERCULES in 2006 using a serial four-stroke marine diesel engine operating on high-sulfur heavy fuel oil. The freshly emitted particles consisted of sulfate, black carbon, organic carbon and ash. We then tracked the particle population for several hours as it evolved undergoing coagulation, dilution with the background air, and chemical transformations in the aerosol and gas phase. This simulation was used to compute the evolution of CCN properties and optical properties of the plume on a per-particle basis. We compared our results to size-resolved data of aged ship plumes from the QUANTIFY Study in 2007 and showed that the model was able to reproduce

  1. Ship Detection Based on Multiple Features in Random Forest Model for Hyperspectral Images

    Li, N.; Ding, L.; Zhao, H.; Shi, J.; Wang, D.; Gong, X.

    2018-04-01

    A novel method for detecting ships which aim to make full use of both the spatial and spectral information from hyperspectral images is proposed. Firstly, the band which is high signal-noise ratio in the range of near infrared or short-wave infrared spectrum, is used to segment land and sea on Otsu threshold segmentation method. Secondly, multiple features that include spectral and texture features are extracted from hyperspectral images. Principal components analysis (PCA) is used to extract spectral features, the Grey Level Co-occurrence Matrix (GLCM) is used to extract texture features. Finally, Random Forest (RF) model is introduced to detect ships based on the extracted features. To illustrate the effectiveness of the method, we carry out experiments over the EO-1 data by comparing single feature and different multiple features. Compared with the traditional single feature method and Support Vector Machine (SVM) model, the proposed method can stably achieve the target detection of ships under complex background and can effectively improve the detection accuracy of ships.

  2. MODEL PENDANAAN ARMADA KAPAL NASIONAL FUNDING MODEL of NATIONAL SHIP ARMADA

    Mohd Ridwan

    2012-02-01

    Full Text Available Domination of Foreign ship armada in trading activity of exsport/import and interisland in Indonesia,couse deficit state 99 trilium rupiah per year. The national shipping armada can not serve sea transportto support commercial activity. They have not provides enough ship armada capacity for tradingcommodity, and dosent enaugh funding development of new ship armada, so that national armada freightcapacity always downwards along increasingly ship age. Economic from transportation sector of seawhich capital intensive, labour intensive and high tech, requires a policy of government which insubvention with funding especially from banking sector and finance companies non bank. It is requiredmodel or funding pattern which to support the sector, expected later national ship armada can transportall commerce commodity of exsport/import and interisland in country

  3. Volcano and ship tracks indicate excessive aerosol-induced cloud water increases in a climate model.

    Toll, Velle; Christensen, Matthew; Gassó, Santiago; Bellouin, Nicolas

    2017-12-28

    Aerosol-cloud interaction is the most uncertain mechanism of anthropogenic radiative forcing of Earth's climate, and aerosol-induced cloud water changes are particularly poorly constrained in climate models. By combining satellite retrievals of volcano and ship tracks in stratocumulus clouds, we compile a unique observational dataset and confirm that liquid water path (LWP) responses to aerosols are bidirectional, and on average the increases in LWP are closely compensated by the decreases. Moreover, the meteorological parameters controlling the LWP responses are strikingly similar between the volcano and ship tracks. In stark contrast to observations, there are substantial unidirectional increases in LWP in the Hadley Centre climate model, because the model accounts only for the decreased precipitation efficiency and not for the enhanced entrainment drying. If the LWP increases in the model were compensated by the decreases as the observations suggest, its indirect aerosol radiative forcing in stratocumulus regions would decrease by 45%.

  4. Establishment and evaluation of a rat model of inhalation lung injury induced by ship smog

    Xin-xin DUAN

    2018-03-01

    Full Text Available Objective To establish and evaluate a rat model of inhalation lung injury induced by ship smog. Methods A rat model of inhalation lung injury was established by analyzing the composition of ship materials after combustion. Forty- two healthy male Wistar rats were randomly divided into normal control group and 2, 6, 12, 24, 48 and 72h groups (6 eachafter inhalation, these rats were killed at each time point, and the changes of arterial blood gas, coagulation function, the lung water content (% were detected. Macroscopic and microscopic changes in lung tissues were observed to judge the degree of lung injury. Results The main components after combustion of 7 kinds of nonmetal materials on ship included CO, CO2, H2S, NOx and other harmful gases in this study, AIKE in one gas detector was used to monitor O2, CO, CO2 and H2S, and their concentrations remained relatively stable within 15 minutes, and the injury time was 15 minutes. The rats presented with shortness of breath and mouth breathing. Smoke inhalation caused a significant hypoxemia, the concentration of blood COHb reached a peak value 2h and the lung water content (% did 6h after inhalation (P<0.05. It is metabolic acidosis in the early stage after inhalation, but metabolic acidosis combined with respiratory acidosis in the later period. Histopathological observation showed diffuse hemorrhage, edema and inflammatory cell infiltration in the lung tissue as manifestations of lung injury, and the injury did not recover at 72h after inhalation, the change of blood coagulation function was not statistically significant. Conclusion A rat model of inhalation lung injury induced by ship smog has been successfully established, and has the advantages of easy replication, stability and reliability, thus can be used to research and treat inhalation lung injury induced by ship smog in naval war environment and other cases. DOI: 10.11855/j.issn.0577-7402.2018.03.14

  5. Nuclear ship engineering simulator

    Itoh, Yasuyoshi; Kusunoki, Tsuyoshi; Hashidate, Koji

    1991-01-01

    The nuclear ship engineering simulator, which analyzes overall system response of nuclear ship numerically, is now being developed by JAERI as an advanced design tool with the latest computer technology in software and hardware. The development of the nuclear ship engineering simulator aims at grasping characteristics of a reactor plant under the situation generated by the combination of ocean, a ship hull and a reactor. The data from various tests with the nuclear ship 'MUTSU' will be used for this simulator to modulate and verify its functions of reproducing realistic response of nuclear ship, and then the simulator will be utilized for the research and development of advanced marine reactors. (author)

  6. Safety analysis report: packages. Argonne National Laboratory SLSF test train shipping container, P-1 shipment. Fissile material. Final report

    Meyer, C.A.

    1975-06-01

    The package is used to ship an instrumented test fuel bundle (test train) containing fissile material. The package assembly is Argonne National Laboratory (ANL) Model R1010-0032. The shipment is fissile class III. The packaging consists of an outer carbon steel container into which an inner container is placed; the inner container is separated from the outer container by urethane foam cushioning material. The test train is supported in the inner container by a series of transverse supports spaced along the length of the test train. Both the inner and outer containers are closed with bolted covers. The covers do not seal the containers in a leaktight manner. The gross weight of the shipment is about 8350 lb. The unirradiated fissile material content is less than 3 kg of UO 2 of up to 93.2 percent enrichment. This is a Type A quantity (transport group III and less than 3 curies) of radioactive material which does not require shielding, cooling or heating, or neutron absorption or moderation functions in its packaging. The maximum exterior dimensions of the container are 37 ft 11 in. long, 24 1 / 2 in. wide, and 19 3 / 4 in. high

  7. Modelling of Surface Ships using Artificial Neural Networks

    Kirkegaard, Poul Henning; Jensen, F. M.; Thoft-Christensen, Palle

    For various design and planning purposes there is at present an increasing interest and a need for numerical modelling of the process of navigating a vessel (or a floating body in general). The reasons for this is that experiments in "full mission" simulators with human navigators at the handles ...

  8. Contribution to the Development of Simulation Model of Ship Turbine

    Božić Ratko

    2015-01-01

    Full Text Available Simulation modelling, performed by System Dynamics Modelling Approach and intensive use of computers, is one of the most convenient and most successful scientific methods of analysis of performance dynamics of nonlinear and very complex natural technical and organizational systems [1]. The purpose of this work is to demonstrate the successful application of system dynamics simulation modelling at analyzing performance dynamics of a complex system of ship’s propulsion system. Gas turbine is a complex non-linear system, which needs to be systematically investigated as a unit consisting of a number of subsystems and elements, which are linked by cause-effect (UPV feedback loops (KPD, both within the propulsion system and with the relevant surrounding. In this paper the authors will present an efficient application of scientific methods for the study of complex dynamic systems called qualitative and quantitative simulation System Dynamics Methodology. Gas turbine will be presented by a set of non-linear differential equations, after which mental-verbal structural models and flowcharts in System dynamics symbols will be produced, and the performance dynamics in load condition will be simulated in POWERSIM simulation language.

  9. Estimation of real ship propelling performance by the surface velocity lattice method using model ship flow field data; Mokeisen ryujo data wo mochiita hyomen uzu koshiho ni yoru jissen suishin seino no suitei

    Kai, H; Ikehata, M; Sakai, S [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1997-10-01

    This is basically a technique wherein the wing element method is replaced by a surface vortex lattice method. A horseshoe vortex of unknown intensity and source surface of known intensity are distributed on the wing surface and, under conditions that the fluid will not cross the boundary, the intensity of horseshoe vortex circulation is calculated for the solution of the fluid field. For the simulation of a real ship in navigation, the required propeller revolution thrust is determined using the real ship resistance value and real ship thrust reduction factor estimated from a model ship resistance test by extrapolation. The calculation of propeller performance is conducted in the quasi-steady condition using the force of fluid working on one wing for each wing angle (with the wing rotated at the increment of 6 degrees), and the thrust and torque are determined using the averages of values obtained in one cycle. It is found that the torque value is overestimated in a considerable degree in the wing element theory. In the surface vortex lattice method, both thrust and torque values agree with experimental values mostly, and this method is found to be accurate enough as a navigation element calculation tool when many panels are considered. 4 refs., 5 figs., 1 tab.

  10. Irradiation test on connector part for nuclear instrumentation of nuclear powered ship 'Mutsu'

    Kudo, Takahiro; Mizushima, Toshihiko; Tsunoda, Tsunemi; Nakazawa, Toshio

    1991-01-01

    The nuclear instrumetnation facility of the nuclear powered ship 'Mutsu' is composed of neutron detectors, signal cables and the circuits for measurement, and ocntinuously monitors neutron flux. Since this facility treats very faint signals, for the signal cables, coaxial cables and triple coaxial cables are used. The coaxial cables for the nuclear instrumentation are equipped with connectors at both ends, and those are called prefabricated cable. The prefabricated cables are connected to neutron detectors, and installed in the detection holes of the primary shielding tank in the containment vessel. Therefore, at the time of reactor operation, they are exposed to high radiation, and the deterioration of the characteristics of the prefabricated cables is feared. For the purpose of confirming that the part of deteriorating the insulation of the prefabricated cables is connectors, and clarifying the cause of the deterioration of insulation in connector part, the irradiation test of this time was carried out. The environment in which the prefabricated cables are laid, the specifications of the cables and connectors, the materials, gamma ray irradiation and the test results are reported. (K.I.)

  11. Modelling Analysis of Echo Signature and Target Strength of a Realistically Modelled Ship Wake for a Generic Forward Looking Active Sonar

    Schippers, P.

    2009-01-01

    The acoustic modelling in TNO’s ALMOST (=Acoustic Loss Model for Operational Studies and Tasks) uses a bubble migration model as realistic input for wake modelling. The modelled bubble cloud represents the actual ship wake. Ship hull, propeller and bow wave are the main generators of bubbles in the

  12. 1/3-scale model testing program

    Yoshimura, H.R.; Attaway, S.W.; Bronowski, D.R.; Uncapher, W.L.; Huerta, M.; Abbott, D.G.

    1989-01-01

    This paper describes the drop testing of a one-third scale model transport cask system. Two casks were supplied by Transnuclear, Inc. (TN) to demonstrate dual purpose shipping/storage casks. These casks will be used to ship spent fuel from DOEs West Valley demonstration project in New York to the Idaho National Engineering Laboratory (INEL) for long term spent fuel dry storage demonstration. As part of the certification process, one-third scale model tests were performed to obtain experimental data. Two 9-m (30-ft) drop tests were conducted on a mass model of the cask body and scaled balsa and redwood filled impact limiters. In the first test, the cask system was tested in an end-on configuration. In the second test, the system was tested in a slap-down configuration where the axis of the cask was oriented at a 10 degree angle with the horizontal. Slap-down occurs for shallow angle drops where the primary impact at one end of the cask is followed by a secondary impact at the other end. The objectives of the testing program were to (1) obtain deceleration and displacement information for the cask and impact limiter system, (2) obtain dynamic force-displacement data for the impact limiters, (3) verify the integrity of the impact limiter retention system, and (4) examine the crush behavior of the limiters. This paper describes both test results in terms of measured deceleration, post test deformation measurements, and the general structural response of the system

  13. Noise source analysis of nuclear ship Mutsu plant using multivariate autoregressive model

    Hayashi, K.; Shimazaki, J.; Shinohara, Y.

    1996-01-01

    The present study is concerned with the noise sources in N.S. Mutsu reactor plant. The noise experiments on the Mutsu plant were performed in order to investigate the plant dynamics and the effect of sea condition and and ship motion on the plant. The reactor noise signals as well as the ship motion signals were analyzed by a multivariable autoregressive (MAR) modeling method to clarify the noise sources in the reactor plant. It was confirmed from the analysis results that most of the plant variables were affected mainly by a horizontal component of the ship motion, that is the sway, through vibrations of the plant structures. Furthermore, the effect of ship motion on the reactor power was evaluated through the analysis of wave components extracted by a geometrical transform method. It was concluded that the amplitude of the reactor power oscillation was about 0.15% in normal sea condition, which was small enough for safe operation of the reactor plant. (authors)

  14. Modeling of nitrogen oxides (NO(x)) concentrations resulting from ships at berth.

    Abdul-Wahab, Sabah A; Elkamel, Ali; Al Balushi, Abdullah S; Al-Damkhi, Ali M; Siddiqui, Rafiq A

    2008-12-01

    Oxides of nitrogen (NO(x)) emissions from ships (marine vessels) contribute to poor air quality that negatively impacts public health and communities in coastal areas and far inland. These emissions often excessively harm human health, environment, wildlife habituates, and quality of life of communities and indigenous of people who live near ports. This study was conducted to assess the impact of NO(x) emissions origination from ships at berth on a nearby community. It was undertaken at Said Bin Sultan Naval base in Wullayat Al-Mussana (Sultanate of Oman) during the year 2005. The Industrial Source Complex Short Term (ISCST) model was adopted to determine the dispersion of NO(x) into port and beyond into surrounding urban areas. The hourly and monthly contours (isopleths) of NO(x) concentrations in and around the port were plotted. The results were analyzed to determine the affected area and the level of NO(x) concentrations. The highest concentration points in the studied area were also identified. The isopleths of NO(x) indicated that most shipping emissions of NO(x) occur at the port can be transported over land. The output results can help to derive advice of recommendations ships operators and environmentalists to take the correct decision to prevent workers and surrounded environment from pollution.

  15. A Path Based Model for a Green Liner Shipping Network Design

    Brouer, Berit Dangaard; Jepsen, Mads Kehlet; Plum, Christian Edinger Munk

    Liner shipping networks are the backbone of international trade providing low transportation cost, which is a major driver of globalization. These networks are under constant pressure to deliver capacity, cost eectiveness and environmentally conscious transport solutions. This article proposes...... a new path based MIP model for the Liner shipping Network Design Problem minimizing the cost of vessels and their fuel consumption facilitating a green network. The proposed model reduces problem size using a novel aggregation of demands. A decomposition method enabling delayed column generation...... is presented. The subproblems have similar structure to Vehicle Routing Problems, which can be solved using dynamic programming. An algorithm has been implemented for this model, unfortunately with discouraging results due to the structure of the subproblem and the lack of proper dominance criteria...

  16. Towards a probabilistic model for predicting ship besetting in ice in Arctic waters

    Fu, Shanshan; Zhang, Di; Montewka, Jakub; Yan, Xinping; Zio, Enrico

    2016-01-01

    Recently, the melting of sea ice due to global warming has made it possible for merchant ships to navigate through Arctic Waters. However, Arctic Marine Transportation System remains a very demanding, dynamic and complex system due to challenging hydro-meteorological conditions, poorly charted waters and remoteness of the area resulting in lack of appropriate response capacity in case of emergency. In order to ensure a proper safety level for operations such as ship transit within the area, a risk analysis should be carried out, where the relevant factors pertaining to a given operation are defined and organized in a model. Such a model can assist onshore managers or ships’ crews in planning and conducting an actual sea passage through Arctic waters. However, research in this domain is scarce, mainly due to lack of data. In this paper, we demonstrate the use of a dataset and expert judgment to determine the risk influencing factors and develop a probabilistic model for a ship besetting in ice along the Northeast Passage. For that purpose, we adopt Bayesian belief Networks (BBNs), due to their predominant feature of reasoning under uncertainty and their ability to accommodate data from various sources. The obtained BBN model has been validated showing good agreement with available state-of-the-art models, and providing good understanding of the analyzed phenomena.

  17. Green Shipping Practices of Shipping Firms

    Young-Tae Chang

    2017-05-01

    Full Text Available The primary objective of this study is to provide an empirical research using structural equation modeling to identify the factors that motivate shipping firms to adopt green shipping practices (GSP. Furthermore, it also examines if adopting GSP can enhance the shipping firms’ environmental and productivity performance. The findings show that shipping firms are motivated to adopt GSP mostly by industrial norms set by institutionalized associations. They are also motivated by customers’ demand for environmental friendliness and their own strategy to make good image. Unlike our expectation, government regulations and international environmental laws are not significant in influencing shipping firms to adopt GSP. Moreover, adoption of green shipping practices can improve the environmental and productivity performance of the shipping firms.

  18. Ship waste quantities prediction model for the port of Belgrade

    VLADANKA PRESBURGER ULNIKOVIĆ

    2011-06-01

    Full Text Available This study focuses on the issues related to the waste management in river ports in general and especially in the port of Belgrade. Data on solid waste, waste oils, oily waters, gray water and black water have been collected for a period of five years. The methodology of data collection is presented. Trends of data were analyzed and the regression model was used to predict the waste quantities in the Belgrade port. This data could be utilized as a basis for the calculation of the equipment capacity for waste selective collection, treatment and storage. The results presented in this study establish the need for an orga¬nized management system for this type of waste which can be achieved either by constructing and providing new specialized terminal or by providing mobile floating facilities and other plants in the Port of Belgrade for these kinds of ser¬vices. In addition to the above, the legislative and organizational strategy of waste management has been explored to complete the study because the im¬pact of good waste management on environment and prevention of environ¬mental accidents would be highly beneficial. This study demonstrated that ad¬dressing these issues should be considered at international as well as national level.

  19. The use of network theory to model disparate ship design information

    Douglas Rigterink

    2014-06-01

    Full Text Available This paper introduces the use of network theory to model and analyze disparate ship design information. This work will focus on a ship's distributed systems and their intra- and intersystem structures and interactions. The three system to be analyzed are: a passageway system, an electrical system, and a fire fighting system. These systems will be analyzed individually using common network metrics to glean information regarding their structures and attributes. The systems will also be subjected to community detection algorithms both separately and as a multiplex network to compare their similarities, differences, and interactions. Network theory will be shown to be useful in the early design stage due to its simplicity and ability to model any shipboard system.

  20. The use of network theory to model disparate ship design information

    Rigterink, Douglas; Piks, Rebecca; Singer, David J.

    2014-06-01

    This paper introduces the use of network theory to model and analyze disparate ship design information. This work will focus on a ship's distributed systems and their intra- and intersystem structures and interactions. The three system to be analyzed are: a passageway system, an electrical system, and a fire fighting system. These systems will be analyzed individually using common network metrics to glean information regarding their structures and attributes. The systems will also be subjected to community detection algorithms both separately and as a multiplex network to compare their similarities, differences, and interactions. Network theory will be shown to be useful in the early design stage due to its simplicity and ability to model any shipboard system.

  1. Ship detection using STFT sea background statistical modeling for large-scale oceansat remote sensing image

    Wang, Lixia; Pei, Jihong; Xie, Weixin; Liu, Jinyuan

    2018-03-01

    Large-scale oceansat remote sensing images cover a big area sea surface, which fluctuation can be considered as a non-stationary process. Short-Time Fourier Transform (STFT) is a suitable analysis tool for the time varying nonstationary signal. In this paper, a novel ship detection method using 2-D STFT sea background statistical modeling for large-scale oceansat remote sensing images is proposed. First, the paper divides the large-scale oceansat remote sensing image into small sub-blocks, and 2-D STFT is applied to each sub-block individually. Second, the 2-D STFT spectrum of sub-blocks is studied and the obvious different characteristic between sea background and non-sea background is found. Finally, the statistical model for all valid frequency points in the STFT spectrum of sea background is given, and the ship detection method based on the 2-D STFT spectrum modeling is proposed. The experimental result shows that the proposed algorithm can detect ship targets with high recall rate and low missing rate.

  2. Study and full-scale test of a high-velocity grade-crossing simulated accident of a locomotive and a nuclear-spent-fuel shipping cask

    Huerta, M.; Yoshimura, H.R.

    1983-02-01

    This report described structural analyses of a high-speed impact between a locomotive and a tractor-trailer system carrying a nuclear-spent-fuel shipping cask. The analyses included both mathematical and physical scale-modeling of the system. The report then describes the full-scale test conducted as part of the program. The system response is described in detail, and a comparison is made between the analyses and the actual hardware response as observed in the full-scale test. 34 figures

  3. Loglinear Rasch model tests

    Kelderman, Hendrikus

    1984-01-01

    Existing statistical tests for the fit of the Rasch model have been criticized, because they are only sensitive to specific violations of its assumptions. Contingency table methods using loglinear models have been used to test various psychometric models. In this paper, the assumptions of the Rasch

  4. DEMONSTRATION OF EQUIVALENCY OF CANE AND SOFTWOOD BASED CELOTEX FOR MODEL 9975 SHIPPING PACKAGES

    Watkins, R; Jason Varble, J

    2008-01-01

    Cane-based Celotex(trademark) has been used extensively in various Department of Energy (DOE) packages as a thermal insulator and impact absorber. Cane-based Celotex(trademark) fiberboard was only manufactured by Knight-Celotex Fiberboard at their Marrero Plant in Louisiana. However, Knight-Celotex Fiberboard shut down their Marrero Plant in early 2007 due to impacts from hurricane Katrina and other economic factors. Therefore, cane-based Celotex(trademark) fiberboard is no longer available for use in the manufacture of new shipping packages requiring the material as a component. Current consolidation plans for the DOE Complex require the procurement of several thousand new Model 9975 shipping packages requiring cane-based Celotex(trademark) fiberboard. Therefore, an alternative to cane-based Celotex(trademark) fiberboard is needed. Knight-Celotex currently manufactures Celotex(trademark) fiberboard from other cellulosic materials, such as hardwood and softwood. A review of the relevant literature has shown that softwood-based Celotex(trademark) meets all parameters important to the Model 9975 shipping package

  5. Evaluation of Cost Leadership Strategy in Shipping Enterprises with Simulation Model

    Ferfeli, Maria V.; Vaxevanou, Anthi Z.; Damianos, Sakas P.

    2009-08-01

    The present study will attempt the evaluation of cost leadership strategy that prevails in certain shipping enterprises and the creation of simulation models based on strategic model STAIR. The above model is an alternative method of strategic applications evaluation. This is held in order to be realised if the strategy of cost leadership creates competitive advantage [1] and this will be achieved via the technical simulation which appreciates the interactions between the operations of an enterprise and the decision-making strategy in conditions of uncertainty with reduction of undertaken risk.

  6. The Aluminum Ship Evaluation Model (ASEM) Static Test Results

    1983-12-01

    8217- -- fC1 (-10,o 1 3 7-1 -69 6 12 960.00 9869 30 0 t SAME 22 R2A:CM7 9-E1 2 23 9 11 -69 822 - 41 fta 𔃼 2S87 98- 3 35 19 I 30 SOME 12 244𔄂 9 ES0 0 0 1 SAME...YE 0D . 0 0 -40 -:0 0 246 344412; FMD 4-A-AS YES 0 1 0. 01 00 _ 0 A 0 204 848117I8 047 YSI .- 0 0 1 -60-A7 1 24 ;41:0 4-A44 YES 0 I 0. 0100 ’-0 -FC 249

  7. Ship Dynamics in the Surf Zone Model Testing

    2008-07-01

    was implemented for ease of transportation and ease of assembly. Each module was 10 feet square consisting of oriented strand board ( OSB ) plywood with...frame, constructed of 2 inch by 4 inch by 10 feet pieces of wood, was measured, cut, laid, and screwed together for each module. Pieces of OSB

  8. Extension of an assessment model of ship traffic exhaust emissions for particulate matter and carbon monoxide

    J.-P. Jalkanen

    2012-03-01

    Full Text Available A method is presented for the evaluation of the exhaust emissions of marine traffic, based on the messages provided by the Automatic Identification System (AIS, which enable the positioning of ship emissions with a high spatial resolution (typically a few tens of metres. The model also takes into account the detailed technical data of each individual vessel. The previously developed model was applicable for evaluating the emissions of NOx, SOx and CO2. This paper addresses a substantial extension of the modelling system, to allow also for the mass-based emissions of particulate matter (PM and carbon monoxide (CO. The presented Ship Traffic Emissions Assessment Model (STEAM2 allows for the influences of accurate travel routes and ship speed, engine load, fuel sulphur content, multiengine setups, abatement methods and waves. We address in particular the modeling of the influence on the emissions of both engine load and the sulphur content of the fuel. The presented methodology can be used to evaluate the total PM emissions, and those of organic carbon, elemental carbon, ash and hydrated sulphate. We have evaluated the performance of the extended model against available experimental data on engine power, fuel consumption and the composition-resolved emissions of PM. We have also compared the annually averaged emission values with those of the corresponding EMEP inventory, As example results, the geographical distributions of the emissions of PM and CO are presented for the marine regions of the Baltic Sea surrounding the Danish Straits.

  9. Calculation models for prediction of Liquefied Natural Gas (LNG) ageing during ship transportation

    Miana, Mario; Hoyo, Rafael del; Rodrigalvarez, Vega; Valdes, Jose Ramon [Instituto Tecnologico de Aragon, Area de Investigacion, Desarrollo y Servicios Tecnologicos, Maria de Luna 7, 50018 Zaragoza (Spain); Llorens, Raul [ENAGAS SA, Direccion de Ingenieria y Tecnologia del Gas, Autovia A - 2, km. 306.4, 50012 Zaragoza (Spain)

    2010-05-15

    A group of European gas transportation companies within the European Gas Research Group launched in 2007 the 'MOLAS' Project to provide a software program for the analysis of the Liquefied Natural Gas (LNG) ageing process during ship transportation. This program contains two different modeling approaches: a physical algorithm and an 'intelligent' model. Both models are fed with the same input data, which is composed of the ship characteristics (BOR and capacity), voyage duration, LNG composition, temperature, pressure, and volume occupied by liquid phase at the port of origin, together with pressure at the port of destination. The results obtained are the LNG composition, temperature and liquid volume at the port of destination. Furthermore, the physical model obtains the evolution over time of such variables en route as it is based on unsteady mass balances over the system, while the i-model applies neural networks to obtain regression coefficients from historical data composed only of origin and destination measurements. This paper describes both models and validates them from previous published models and experimental data measured in ENAGAS LNG regasification plants. (author)

  10. A service flow model for the liner shipping network design problem

    Plum, Christian Edinger Munk; Pisinger, David; Sigurd, Mikkel M.

    2014-01-01

    . The formulation alleviates issues faced by arc flow formulations with regards to handling multiple calls to the same port. A problem which has not been fully dealt with earlier by LSNDP formulations. Multiple calls are handled by introducing service nodes, together with port nodes in a graph representation...... of the network and a penalty for not flowed cargo. The model can be used to design liner shipping networks to utilize a container carrier’s assets efficiently and to investigate possible scenarios of changed market conditions. The model is solved as a Mixed Integer Program. Results are presented for the two...

  11. Modeling Distribution and Abundance of Antarctic Baleen Whales Using Ships of Opportunity

    Rob Williams

    2006-06-01

    Full Text Available Information on animal abundance and distribution is at the cornerstone of many wildlife and conservation strategies. However, these data can be difficult and costly to obtain for cetacean species. The expense of sufficient ship time to conduct design-unbiased line transect surveys may be simply out of reach for researchers in many countries, which nonetheless grapple with problems of conservation of endangered species, by-catch of small cetaceans in commercial fisheries, and progression toward ecosystem-based fisheries management. Recently developed spatial modeling techniques show promise for estimating wildlife abundance using non-randomized surveys, but have yet to receive much field-testing in areas where designed surveys have also been conducted. Effort and sightings data were collected along 9 650 km of transects aboard ships of opportunity in the Southern Ocean during the austral summers of 2000-2001 and 2001-2002. Generalized additive models with generalized cross-validation were used to express heterogeneity of cetacean sightings as functions of spatial covariates. Models were used to map predicted densities and to estimate abundance of humpback, minke, and fin whales in the Drake Passage and along the Antarctic Peninsula. All species' distribution maps showed strong density gradients, which were robust to jackknife resampling when each of 14 trips was removed sequentially with replacement. Looped animations of model predictions of whale density illustrate uncertainty in distribution estimates in a way that is informative to non-scientists. The best abundance estimate for humpback whales was 1 829 (95% CI: 978-3 422. Abundance of fin whales was 4 487 (95% CI: 1 326-15 179 and minke whales was 1,544 (95% CI: 1,221-1,953. These estimates agreed roughly with those reported from a designed survey conducted in the region during the previous austral summer. These estimates assumed that all animals on the trackline were detected, but

  12. Earthquake likelihood model testing

    Schorlemmer, D.; Gerstenberger, M.C.; Wiemer, S.; Jackson, D.D.; Rhoades, D.A.

    2007-01-01

    INTRODUCTIONThe Regional Earthquake Likelihood Models (RELM) project aims to produce and evaluate alternate models of earthquake potential (probability per unit volume, magnitude, and time) for California. Based on differing assumptions, these models are produced to test the validity of their assumptions and to explore which models should be incorporated in seismic hazard and risk evaluation. Tests based on physical and geological criteria are useful but we focus on statistical methods using future earthquake catalog data only. We envision two evaluations: a test of consistency with observed data and a comparison of all pairs of models for relative consistency. Both tests are based on the likelihood method, and both are fully prospective (i.e., the models are not adjusted to fit the test data). To be tested, each model must assign a probability to any possible event within a specified region of space, time, and magnitude. For our tests the models must use a common format: earthquake rates in specified “bins” with location, magnitude, time, and focal mechanism limits.Seismology cannot yet deterministically predict individual earthquakes; however, it should seek the best possible models for forecasting earthquake occurrence. This paper describes the statistical rules of an experiment to examine and test earthquake forecasts. The primary purposes of the tests described below are to evaluate physical models for earthquakes, assure that source models used in seismic hazard and risk studies are consistent with earthquake data, and provide quantitative measures by which models can be assigned weights in a consensus model or be judged as suitable for particular regions.In this paper we develop a statistical method for testing earthquake likelihood models. A companion paper (Schorlemmer and Gerstenberger 2007, this issue) discusses the actual implementation of these tests in the framework of the RELM initiative.Statistical testing of hypotheses is a common task and a

  13. Field test of available methods to measure remotely SOx and NOx emissions from ships

    Balzani Lööv, J.M.; Alfoldy, B.; Gast, L.F.L.; Hjorth, J.; Lagler, F.; Mellqvist, J.; Beecken, J.; Berg, N.; Duyzer, J.; Westrate, H.; Swart, D.P.J.; Berkhout, A.J.C.; Jalkanen, J.P.; Prata, A.J.; Van Der Hoff, G.R.; Borowiak, A.

    2014-01-01

    Methods for the determination of ship fuel sulphur content and NOx emission factors based on remote measurements have been compared in the harbour of Rotterdam and compared to direct stack emission measurements on the ferry Stena Hollandica. The methods were selected based on a review of the

  14. Guidelines for conducting impact tests on shipping packages for radioactive material

    Mok, G.C.; Carlson, R.W.; Lu, S.C.; Fischer, L.E.

    1995-09-01

    Federal regulation (10 CFR Part 71) specifies a number of impact conditions (free-drop, penetration, and puncture), under which a package for the transport of radioactive materials must be tested or evaluated to demonstrate compliance with the regulation. This report is a comprehensive guide to the planning and execution of these impact tests. The report identifies the required considerations for both the design, pre-, and post-test inspections of the test model and the measurement, recording, analysis, and reporting of the test data. The report also presents reasons for the requirements, identifies the major difficulties in meeting these requirements, and suggests possible methods to overcome the difficulties. Discussed in substantial detail is the use of scale models and instrumented measurements

  15. S-CNN-BASED SHIP DETECTION FROM HIGH-RESOLUTION REMOTE SENSING IMAGES

    R. Zhang

    2016-06-01

    Full Text Available Reliable ship detection plays an important role in both military and civil fields. However, it makes the task difficult with high-resolution remote sensing images with complex background and various types of ships with different poses, shapes and scales. Related works mostly used gray and shape features to detect ships, which obtain results with poor robustness and efficiency. To detect ships more automatically and robustly, we propose a novel ship detection method based on the convolutional neural networks (CNNs, called SCNN, fed with specifically designed proposals extracted from the ship model combined with an improved saliency detection method. Firstly we creatively propose two ship models, the “V” ship head model and the “||” ship body one, to localize the ship proposals from the line segments extracted from a test image. Next, for offshore ships with relatively small sizes, which cannot be efficiently picked out by the ship models due to the lack of reliable line segments, we propose an improved saliency detection method to find these proposals. Therefore, these two kinds of ship proposals are fed to the trained CNN for robust and efficient detection. Experimental results on a large amount of representative remote sensing images with different kinds of ships with varied poses, shapes and scales demonstrate the efficiency and robustness of our proposed S-CNN-Based ship detector.

  16. A policy-oriented cost model for shipping commodities by truck.

    2009-12-01

    Surprisingly, transportation planners and policy makers do not have the ability to estimate the cost of shipping a quantity of a commodity between two : locations for broad categories of goods. Costs of shipping are important components in mode, rout...

  17. Construction of Monitoring Model and Algorithm Design on Passenger Security during Shipping Based on Improved Bayesian Network

    Wang, Jiali; Zhang, Qingnian; Ji, Wenfeng

    2014-01-01

    A large number of data is needed by the computation of the objective Bayesian network, but the data is hard to get in actual computation. The calculation method of Bayesian network was improved in this paper, and the fuzzy-precise Bayesian network was obtained. Then, the fuzzy-precise Bayesian network was used to reason Bayesian network model when the data is limited. The security of passengers during shipping is affected by various factors, and it is hard to predict and control. The index system that has the impact on the passenger safety during shipping was established on basis of the multifield coupling theory in this paper. Meanwhile, the fuzzy-precise Bayesian network was applied to monitor the security of passengers in the shipping process. The model was applied to monitor the passenger safety during shipping of a shipping company in Hainan, and the effectiveness of this model was examined. This research work provides guidance for guaranteeing security of passengers during shipping. PMID:25254227

  18. Littoral Combat Ship: Additional Testing and Improved Weight Management Needed Prior to Further Investments

    2014-07-01

    monohull design with a steel hull and aluminum superstructure, while the Austal USA Independence variant (LCS 2 and other even- Background Seaframe...including Singapore; Malaysia ; Brunei; and Indonesia. The ship also conducted some real-world operations as directed by the 7th Fleet, such as...requirements for service life allowances already fall short of the growth margins called for under Navy and industry recommended practice.21 Table 8: Navy

  19. A Decision Mixture Model-Based Method for Inshore Ship Detection Using High-Resolution Remote Sensing Images.

    Bi, Fukun; Chen, Jing; Zhuang, Yin; Bian, Mingming; Zhang, Qingjun

    2017-06-22

    With the rapid development of optical remote sensing satellites, ship detection and identification based on large-scale remote sensing images has become a significant maritime research topic. Compared with traditional ocean-going vessel detection, inshore ship detection has received increasing attention in harbor dynamic surveillance and maritime management. However, because the harbor environment is complex, gray information and texture features between docked ships and their connected dock regions are indistinguishable, most of the popular detection methods are limited by their calculation efficiency and detection accuracy. In this paper, a novel hierarchical method that combines an efficient candidate scanning strategy and an accurate candidate identification mixture model is presented for inshore ship detection in complex harbor areas. First, in the candidate region extraction phase, an omnidirectional intersected two-dimension scanning (OITDS) strategy is designed to rapidly extract candidate regions from the land-water segmented images. In the candidate region identification phase, a decision mixture model (DMM) is proposed to identify real ships from candidate objects. Specifically, to improve the robustness regarding the diversity of ships, a deformable part model (DPM) was employed to train a key part sub-model and a whole ship sub-model. Furthermore, to improve the identification accuracy, a surrounding correlation context sub-model is built. Finally, to increase the accuracy of candidate region identification, these three sub-models are integrated into the proposed DMM. Experiments were performed on numerous large-scale harbor remote sensing images, and the results showed that the proposed method has high detection accuracy and rapid computational efficiency.

  20. Automation of measurement of heights waves around a model ship; Mokeisen mawari no hako keisoku no jidoka

    Ikehata, M; Kato, M; Yanagida, F [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1997-10-01

    Trial fabrication and tests were performed on an instrument to automate measurement of heights of waves around a model ship. The currently used electric wave height measuring instrument takes long time for measurement, hence poor in efficiency. The method for processing optical images also has a problem in accuracy. Therefore, a computer controlled system was structured by using AC servo motors in driving the X and Y axes of a traverse equipment. Equipment was fabricated to automate the wave height measurement, in which four servo type wave height meters are installed on a moving rack in the lateral (Y-axial) direction so that wave heights to be measured by four meters can be measured automatically all at once. Wave heights can be measured continuously by moving the moving rack at a constant speed, verifying that wave shapes in longitudinal cross sections can be acquired by only one towing. Time required in the measurements using the instrument was 40 hours as a net time for fixed point measurement and 12 hours for continuous measurement, or 52 hours in total. On the other hand, the time may reach 240 hours for fixed point measurement when the conventional all-point manual traverse equipment is used. Enormous effects were obtained from automating the instrument. Collection of wave height data will continue also on tankers and other types of ships. 2 refs., 8 figs., 1 tab.

  1. Investigation of the Effects of Ship Induced Waves on the Littoral Zone with Field Measurements and CFD Modeling

    Gábor Fleit

    2016-07-01

    Full Text Available Waves induced by ship movement might be harmful for the habitat in the littoral zone of rivers due to the temporally increasing bed shear stress, the high-energy breaking waves and the consequently related detachment of benthic animals. In order to understand the complex hydrodynamic phenomena resulting from littoral waves, we present the testing of a novel methodology that incorporates field observations and numerical tools. The study is performed at a section of the Danube River in Hungary and analyzes the influence of different ship types. The field methods consist of parallel acoustic measurements (using Acoustic Doppler Velocimetry (ADV conducted at the riverbed and Large Scale Particle Image Velocimetry (LSPIV of the water surface. ADV measurements provided near-bed flow velocities based on which the wave induced currents and local bed shear stress could be estimated. The LSPIV was able to quantify the dynamics of the breaking waves along the bank. Furthermore, computational fluid dynamics (CFD modeling was successfully applied to simulate the propagation and the breaking of littoral waves. The used techniques complement each other well and their joint application provides an adequate tool to support the improvement of riverine habitats.

  2. Probability of Ship on Collision Courses Based on the New PAW Using MMG Model and AIS Data

    I Putu Sindhu Asmara

    2015-03-01

    Full Text Available This paper proposes an estimation method for ships on collision courses taking crash astern maneuvers based on a new potential area of water (PAW for maneuvering. A crash astern maneuver is an emergency option a ship can take when exposed to the risk of a collision with other ships that have lost control. However, lateral forces and yaw moments exerted by the reversing propeller, as well as the uncertainty of the initial speed and initial yaw rate, will move the ship out of the intended stopping position landing it in a dangerous area. A new PAW for crash astern maneuvers is thus introduced. The PAW is developed based on a probability density function of the initial yaw rate. Distributions of the yaw rates and speeds are analyzed from automatic identification system (AIS data in Madura Strait, and estimated paths of the maneuvers are simulated using a mathematical maneuvering group model.

  3. Frequency Transient Suppression in Hybrid Electric Ship Power Systems: A Model Predictive Control Strategy for Converter Control with Energy Storage

    Viknash Shagar

    2018-03-01

    Full Text Available This paper aims to understand how the common phenomenon of fluctuations in propulsion and service load demand contribute to frequency transients in hybrid electric ship power systems. These fluctuations arise mainly due to changes in sea conditions resulting in significant variations in the propulsion load demand of ships. This leads to poor power quality for the power system that can potentially cause hazardous conditions such as blackout on board the ship. Effects of these fluctuations are analysed using a hybrid electric ship power system model and a proposed Model Predictive Control (MPC strategy to prevent propagation of transients from the propellers into the shipboard power system. A battery energy storage system, which is directly connected to the DC-link of the frequency converter, is used as the smoothing element. Case studies that involve propulsion and service load changes have been carried out to investigate the efficacy of the proposed solution. Simulation results show that the proposed solution with energy storage and MPC is able to contain frequency transients in the shipboard power system within the permissible levels stipulated by the relevant power quality standards. These findings will help ship builders and operators to consider using battery energy storage systems controlled by advanced control techniques such as MPC to improve the power quality on board ships.

  4. Thermal response modeling of a contact-handled transuranic waste shipping container system to a fire

    Suchsland, K.E.; Kwong, K.C.; Fretter, E.F.; Boyd, R.D.; Auerbach, I.; Yoshimura, H.R.

    1980-01-01

    A one-dimensional thermal model has been developed to predict the response of a transuranic (TRU) waste shipping container accidentally exposed to a fire environment. The basic wall structure of the container consists of polyurethane foam (64 kg/m 3 ) sandwiched between two steel plates. The foam thermal model, based on high temperature experimental data, is developed for the case in which the virgin foam is in a nonoxidizing environment. The experimental results indicate that foam decomposition is highly heat rate dependent. At low quasi-steady heating rates, the foam changes to a bubbling black viscous liquid. At very high heating rates, pyrolysis gases are formed as the foam decomposes and a 20% (by weight) residual char remains. This porous char acts as a radiation shield which can significantly reduce thermal transport. In the case of a TRU shipping container wall, this char will slow the thermal penetration rate and drastically reduce the heat load to the container contents. When the front surface of the wall was subjected to 1333 0 K, numerical computations predict that after approximately 1800 s the foam temperature rise at a depth of 10.2 cm was less than 200 K (uncharred). After approximately 3600 s the foam temperature rise at a depth of 20.4 cm was 23 0 K. Typical waste contents temperature rise was predicted to be less than 56 0 K after 3600 s of heating

  5. Modeling Ships and Space Craft The Science and Art of Mastering the Oceans and Sky

    Hagler, Gina

    2013-01-01

    Modeling Ships and Space Craft: The Science and Art of Mastering the Oceans and Sky begins with the theories of Aristotle and Archimedes, moving on to examine the work of Froude and Taylor, the early aviators and the Wright Brothers, Goddard and the other rocket men, and the computational fluid dynamic models of our time. It examines the ways each used fluid dynamic principles in the design of their vessels. In the process, this book covers the history of hydrodynamic (aero and fluid) theory and its progression – with some very accessible science examples – including seminal theories. Hydrodynamic principles in action are also explored with examples from nature and the works of man. This is a book for anyone interested in the history of technology – specifically the methods and science behind the use of scale models and hydrodynamic principles in the marine and aeronautical designs of today.

  6. Large scale model testing

    Brumovsky, M.; Filip, R.; Polachova, H.; Stepanek, S.

    1989-01-01

    Fracture mechanics and fatigue calculations for WWER reactor pressure vessels were checked by large scale model testing performed using large testing machine ZZ 8000 (with a maximum load of 80 MN) at the SKODA WORKS. The results are described from testing the material resistance to fracture (non-ductile). The testing included the base materials and welded joints. The rated specimen thickness was 150 mm with defects of a depth between 15 and 100 mm. The results are also presented of nozzles of 850 mm inner diameter in a scale of 1:3; static, cyclic, and dynamic tests were performed without and with surface defects (15, 30 and 45 mm deep). During cyclic tests the crack growth rate in the elastic-plastic region was also determined. (author). 6 figs., 2 tabs., 5 refs

  7. An adaptive simulation model for analysis of nuclear material shipping operations

    Boerigter, S.T.; Sena, D.J.; Fasel, J.H.

    1998-01-01

    Los Alamos has developed an advanced simulation environment designed specifically for nuclear materials operations. This process-level simulation package, the Process Modeling System (ProMoS), is based on high-fidelity material balance criteria and contains intrinsic mechanisms for waste and recycle flows, contaminant estimation and tracking, and material-constrained operations. Recent development efforts have focused on coupling complex personnel interactions, personnel exposure calculations, and stochastic process-personnel performance criteria to the material-balance simulation. This combination of capabilities allows for more realistic simulation of nuclear material handling operations where complex personnel interactions are required. They have used ProMoS to assess fissile material shipping performance characteristics at the Los Alamos National Laboratory plutonium facility (TA-55). Nuclear material shipping operations are ubiquitous in the DOE complex and require the largest suite of varied personnel interacting in a well-timed manner to accomplish the task. They have developed a baseline simulation of the present operations and have estimated the operational impacts and requirement of the pit production mission at TA-55 as a result of the SSM-PEIS. Potential bottlenecks have been explored and mechanisms for increasing operational efficiency are identified

  8. Nonlinear analysis for a ship with a general roll-damping model

    El-Bassiouny, A F [Mathematics Department, Faculty of Science, Benha University, Benha 13518 (Egypt)

    2007-05-15

    The qualitative behaviour of the response of a ship rolling in longitudinal waves whose amplitude or frequency (parameters) are slowly varied is presented. An analytical and numerical technique is used to predict the qualitative change taking place in the stable solutions of a ship model as one of the parameters is slowly changed. The analysis took into consideration linear, cubic and quantic terms in the polynomial expansion of the relative roll angle. The damping moment consists of the linear term associated with radiation and viscous damping and a cubic term due to frictional resistance and eddies behind bilge keels and hard bilge corners. Two methods (the averaging and the multiple time scales) are used to investigate a first-order approximate analytical solution. The modulation equations of the amplitudes and phases are obtained. These equations are used to determine steady state solutions. Numerical calculations are presented which illustrate the behaviour of the steady state response amplitude as a function of the detuning parameter. The stability of the proposed solution is determined applying Liapunov's first method. The effects of different parameters on the system behaviour are investigated numerically. The results obtained by the two methods are in excellent agreement.

  9. FACSIM/MRS (Monitored Retrievable Storage)-2: Storage and shipping model documentation and user's guide

    Huber, H.D.; Chockie, A.D.; Hostick, C.J.; Otis, P.T.; Sovers, R.A.

    1987-06-01

    The Pacific Northwest Laboratory (PNL) has developed a stochastic computer model, FACSIM/MRS, to assist in assessing the operational performance of the Monitored Retrievable Storage (MRS) waste-handling facility. This report provides the documentation and user's guide for FACSIM/MRS-2, which is also referred to as the back-end model. The FACSIM/MRS-2 model simulates the MRS storage and shipping operations, which include handling canistered spent fuel and secondary waste in the shielded canyon cells, in onsite yard storage, and in repository shipping cask loading areas.

  10. The use of network theory to model disparate ship design information

    Rigterink Douglas

    2014-06-01

    Full Text Available This paper introduces the use of network theory to model and analyze disparate ship design information. This work will focus on a ship’s distributed systems and their intra- and intersystem structures and interactions. The three system to be analyzed are: a passageway system, an electrical system, and a fire fighting system. These systems will be analyzed individually using common network metrics to glean information regarding their structures and attributes. The systems will also be subjected to community detection algorithms both separately and as a multiplex network to compare their similarities, differences, and interactions. Network theory will be shown to be useful in the early design stage due to its simplicity and ability to model any shipboard system.

  11. Wind Forces on Container Ships

    Andersen, Ingrid Marie Vincent

    2012-01-01

    An investigation of the wind forces acting on a 9,000+ TEU container ship has been carried out through a series of wind tunnel tests. It was investigated how the wind forces depend on the container configuration on the deck using a 1:450 scale model and a series of appropriate container...... are presented as nondimensional coefficients. It is concluded, that the measured forces and moment depend on the container configuration on deck, and the results may provide a general idea of how the magnitude of the wind forces is affected by a given container stacking configuration on a similar container ship....

  12. Testing the standard model

    Gordon, H.; Marciano, W.; Williams, H.H.

    1982-01-01

    We summarize here the results of the standard model group which has studied the ways in which different facilities may be used to test in detail what we now call the standard model, that is SU/sub c/(3) x SU(2) x U(1). The topics considered are: W +- , Z 0 mass, width; sin 2 theta/sub W/ and neutral current couplings; W + W - , Wγ; Higgs; QCD; toponium and naked quarks; glueballs; mixing angles; and heavy ions

  13. Sixth Status Report: Testing of Aged Softwood Fiberboard Material for the 9975 Shipping Package

    Daugherty, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-03-31

    Samples have been prepared from several 9975 lower fiberboard subassemblies fabricated from softwood fiberboard. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples, with a few differences. Some softwood fiberboard properties tend to degrade faster in some environments, while some cane fiberboard properties degrade faster in the two most aggressive environments. As a result, it is premature to assume both materials will age at the same rates, and the preliminary aging models developed for cane fiberboard might not apply to softwood fiberboard. However, it is expected that both cane and softwood fiberboard assemblies will perform satisfactorily in conforming packages stored in a typical KAC storage environment for up to 15 years. Samples from an additional 3 softwood fiberboard assemblies have begun aging during the past year to provide information on the variability of softwood fiberboard behavior. Aging and testing of softwood fiberboard will continue and additional data will be collected to support development of an aging model specific to softwood fiberboard.

  14. Safety of nuclear ships

    1978-01-01

    Interest in the utilization of nuclear steam supply systems for merchant ships and icebreakers has recently increased considerably due to the sharp rise in oil prices and the continuing trend towards larger and faster merchant ships. Canada, for example, is considering construction of an icebreaker in the near future. On the other hand, an accident which could result in serious damage to or the sinking of a nuclear ship is potentially far more dangerous to the general public than a similar accident with a conventional ship. Therefore, it was very important to evaluate in an international forum the safety of nuclear ships in the light of our contemporary safety philosophy, taking into account the results of cumulative operating experience with nuclear ships in operation. The philosophy and safety requirement for land-based nuclear installations were outlined because of many common features for both land-based nuclear installations and nuclear ships. Nevertheless, essential specific safety requirements for nuclear ships must always be considered, and the work on safety problems for nuclear ships sponsored by the NEA was regarded as an important step towards developing an international code of practice by IMCO on the safety of nuclear merchant ships. One session was devoted to the quantitative assessment of nuclear ship safety. The probability technique of an accident risk assessment for nuclear power plants is well known and widely used. Its modification, to make it applicable to nuclear propelled merchant ships, was discussed in some papers. Mathematical models for describing various postulated accidents with nuclear ships were developed and reported by several speakers. Several papers discussed a loss-of-coolant accident (LOCA) with nuclear steam supply systems of nuclear ships and engineering design features to prevent a radioactive effluence after LOCA. Other types of postulated accidents with reactors and systems in static and dynamic conditions were also

  15. Influences of the separation distance, ship speed and channel dimension on ship maneuverability in a confined waterway

    Du, Peng; Ouahsine, Abdellatif; Sergent, Philippe

    2018-05-01

    Ship maneuvering in the confined inland waterway is investigated using the system-based method, where a nonlinear transient hydrodynamic model is adopted and confinement models are implemented to account for the influence of the channel bank and bottom. The maneuvering model is validated using the turning circle test, and the confinement model is validated using the experimental data. The separation distance, ship speed, and channel width are then varied to investigate their influences on ship maneuverability. With smaller separation distances and higher speeds near the bank, the ship's trajectory deviates more from the original course and the bow is repelled with a larger yaw angle, which increase the difficulty of maneuvering. Smaller channel widths induce higher advancing resistances on the ship. The minimum distance to the bank are extracted and studied. It is suggested to navigate the ship in the middle of the channel and with a reasonable speed in the restricted waterway.

  16. Wave Reflection Model Tests

    Burcharth, H. F.; Larsen, Brian Juul

    The investigation concerns the design of a new internal breakwater in the main port of Ibiza. The objective of the model tests was in the first hand to optimize the cross section to make the wave reflection low enough to ensure that unacceptable wave agitation will not occur in the port. Secondly...

  17. Modelling the emissions from ships in ports and their impact on air quality in the metropolitan area of Hamburg

    Ramacher, Martin; Karl, Matthias; Aulinger, Armin; Bieser, Johannes; Matthias, Volker; Quante, Markus

    2016-04-01

    Exhaust emissions from shipping contribute significantly to the anthropogenic burden of air pollutants such as nitrogen oxides (NOX) and particulate matter (PM). Ships emit not only when sailing on open sea, but also when approaching harbors, during port manoeuvers and at berth to produce electricity and heat for the ship's operations. This affects the population of harbor cities because long-term exposure to PM and NOX has significant effects on human health. The European Union has therefore has set air quality standards for air pollutants. Many port cities have problems meeting these standards. The port of Hamburg with around 10.000 ship calls per year is Germany's largest seaport and Europe's second largest container port. Air quality standard reporting in Hamburg has revealed problems in meeting limits for NO2 and PM10. The amount and contribution of port related ship emissions (38% for NOx and 17% for PM10) to the overall emissions in the metropolitan area in 2005 [BSU Hamburg (2012): Luftreinhalteplan für Hamburg. 1. Fortschreibung 2012] has been modelled with a bottom up approach by using statistical data of ship activities in the harbor, technical vessel information and specific emission algorithms [GAUSS (2008): Quantifizierung von gasförmigen Emissionen durch Maschinenanlagen der Seeschiffart an der deutschen Küste]. However, knowledge about the spatial distribution of the harbor ship emissions over the city area is crucial when it comes to air quality standards and policy decisions to protect human health. Hence, this model study examines the spatial distribution of harbor ship emissions (NOX, PM10) and their deposition in the Hamburg metropolitan area. The transport and chemical transformation of atmospheric pollutants is calculated with the well-established chemistry transport model TAPM (The Air Pollution Model). TAPM is a three-dimensional coupled prognostic meteorological and air pollution model with a condensed chemistry scheme including

  18. Testing the Standard Model

    Riles, K

    1998-01-01

    The Large Electron Project (LEP) accelerator near Geneva, more than any other instrument, has rigorously tested the predictions of the Standard Model of elementary particles. LEP measurements have probed the theory from many different directions and, so far, the Standard Model has prevailed. The rigour of these tests has allowed LEP physicists to determine unequivocally the number of fundamental 'generations' of elementary particles. These tests also allowed physicists to ascertain the mass of the top quark in advance of its discovery. Recent increases in the accelerator's energy allow new measurements to be undertaken, measurements that may uncover directly or indirectly the long-sought Higgs particle, believed to impart mass to all other particles.

  19. Application of Quantitative Models, MNLR and ANN in Short Term Forecasting of Ship Data

    P.Oliver Jayaprakash; K. Gunasekaran

    2011-01-01

    Forecasting has been the trouble-free way for the port authorities to derive the future expected values of service time of Bulk cargo ships handled at ports of South India. The short term forecasting could be an effective tool for estimating the resource requirements of recurring ships of similar tonnage and Cargo. Forecasting the arrival data related to port based ship operations customarily done using the standard algorithms and assumptions. The regular forecasting methods were decompositio...

  20. Investigation of the hydrodynamic model test of forced rolling for a barge using PIV

    WANG Xiaoqiang

    2017-03-01

    Full Text Available In order to study the physical details of viscous flow in ship roll motions and improve the accuracy of ship roll damping numerical simulation, the application of the Particle Image Velocimetry (PIV technique is investigated in model tests of forced ship rolling in calm water. The hydrodynamic force and flow field at the bilge region are simultaneously measured for barges at different amplitudes and frequencies in which the self-made forced rolling facility was used. In the model test, the viscous flow variation with the time around the bilge region was studied during ship rolling motion. The changes in ship roll damping coefficients with the rolling amplitude and period were also investigated. A comparison of the model test results with the Computational Fluid Dynamics(CFDresults shows that the numerical ship roll damping coefficients agree well with the model test results, while the differences in the local flow details exist between the CFD results and model test results. Further research into the model test technique and CFD application is required.

  1. Antecedent Characteristics of Online Cancer Information Seeking Among Rural Breast Cancer Patients: An Application of the Cognitive-Social Health Information Processing (C-SHIP) Model

    Shaw, Bret R.; DuBenske, Lori L.; Han, Jeong Yeob; Cofta-Woerpel, Ludmila; Bush, Nigel; Gustafson, David H.; McTavish, Fiona

    2013-01-01

    Little research has examined the antecedent characteristics of patients most likely to seek online cancer information. This study employs the Cognitive-Social Health Information Processing (C-SHIP) model as a framework to understand what psychosocial characteristics precede online cancer-related information seeking among rural breast cancer patients who often have fewer healthcare providers and limited local support services. Examining 144 patients who were provided free computer hardware, Internet access and training for how to use an Interactive Cancer Communication System, pre-test survey scores indicating patients’ psychosocial status were correlated with specific online cancer information seeking behaviors. Each of the factors specified by the C-SHIP model had significant relationships with online cancer information seeking behaviors with the strongest findings emerging for cancer-relevant encodings and self-construals, cancer-relevant beliefs and expectancies and cancer-relevant self-regulatory competencies and skills. Specifically, patients with more negative appraisals in these domains were more likely to seek out online cancer information. Additionally, antecedent variables associated with the C-SHIP model had more frequent relationships with experiential information as compared to didactic information. This study supports the applicability of the model to discern why people afflicted with cancer may seek online information to cope with their disease. PMID:18569368

  2. 航运战略联盟构建模型%Model of strategic shipping alliance construction

    高志军; 刘伟; 朱卫平

    2012-01-01

    In order to study the factors which affect the strategic shipping alliance construction, the essence and types of strategic shipping alliance are analyzed qualitatively and systematically on the basis of study and analysis of strategic alliance theory. The structure-culture-risk factors are combined with the process of strategic shipping alliance construction. The theoretical model of strategic shipping alliance construction is built, and a case is provided. The study shows that the model has some guiding significance for the strategic shipping alliance construction.%为研究影响航运战略联盟构建成功的因素,在战略联盟理论研究分析的基础上,对航运战略联盟的内涵和类型进行较为系统的定性分析.将结构、文化和风险等因素与航运战略联盟构建的过程相结合,建立航运战略联盟构建的理论模型,并进行案例分析.分析表明,该模型对航运战略联盟的构建具有一定的指导意义.

  3. Radiant heat testing of the H1224A shipping/storage container

    Harding, D.C.; Bobbe, J.G.; Stenberg, D.R.; Arviso, M.

    1994-05-01

    H1224A weapons containers have been used for years by the Departments of Energy and Defense to transport and store W78 warhead midsections. Although designed to protect the midsections only from low-energy impacts, a recent transportation risk assessment effort has identified a need to evaluate the container`s ability to protect weapons in more severe accident environments. Four radiant heat tests were performed: two each on an H1224A container (with a Mk12a Mod 6c mass mock-up midsection inside) and two on a low-cost simulated H1224A container (with a hollow Mk12 aeroshell midsections inside). For each unit tested, temperatures were recorded at numerous points throughout the container and midsection during a 4-hour 121{degrees}C (250{degrees}F) and 30-minute 1010{degrees}C (1850{degrees}F) radiant environment. Measured peak temperatures experienced by the inner walls of the midsections as a result of exposure to the high-temperature radiant environment ranged from 650{degrees} C to 980{degrees} C (1200{degrees} F to 1800{degrees}F) for the H1224A container and 770 {degrees} to 990 {degrees}C (1420{degrees} F to 1810{degrees}F) for the simulated container. The majority of both containers were completely destroyed during the high-temperature test. Temperature profiles will be used to benchmark analytical models and predict warhead midsection temperatures over a wide range of the thermal accident conditions.

  4. Development of Tsunami Numerical Model Considering the Disaster Debris such as Cars, Ships and Collapsed Buildings

    Kozono, Y.; Takahashi, T.; Sakuraba, M.; Nojima, K.

    2016-12-01

    A lot of debris by tsunami, such as cars, ships and collapsed buildings were generated in the 2011 Tohoku tsunami. It is useful for rescue and recovery after tsunami disaster to predict the amount and final position of disaster debris. The transport form of disaster debris varies as drifting, rolling and sliding. These transport forms need to be considered comprehensively in tsunami simulation. In this study, we focused on the following three points. Firstly, the numerical model considering various transport forms of disaster debris was developed. The proposed numerical model was compared with the hydraulic experiment by Okubo et al. (2004) in order to verify transport on the bottom surface such as rolling and sliding. Secondly, a numerical experiment considering transporting on the bottom surface and drifting was studied. Finally, the numerical model was applied for Kesennuma city where serious damage occurred by the 2011 Tohoku tsunami. In this model, the influence of disaster debris was considered as tsunami flow energy loss. The hydraulic experiments conducted in a water tank which was 10 m long by 30 cm wide. The gate confined water in a storage tank, and acted as a wave generator. A slope was set at downstream section. The initial position of a block (width: 3.2 cm, density: 1.55 g/cm3) assuming the disaster debris was placed in front of the slope. The proposed numerical model simulated well the maximum transport distance and the final stop position of the block. In the second numerical experiment, the conditions were the same as the hydraulic experiment, except for the density of the block. The density was set to various values (from 0.30 to 4.20 g/cm3). This model was able to estimate various transport forms including drifting and sliding. In the numerical simulation of the 2011 Tohoku tsunami, the condition of buildings was modeled as follows: (i)the resistance on the bottom using Manning roughness coefficient (conventional method), and (ii)structure of

  5. Thermal hydro-dynamic behavior of the nuclear-powered ship Mutsu in the power-up test

    Ishida, Toshihisa; Kusunoki, Tsuyoshi; Tanaka, Yoshimi; Yao, Toshiaki; Inoue, Kimio; Ochiai, Masa-aki

    1991-01-01

    The first Japanese nuclear ship N.S. Mutsu was tested with heavy load changes as ones of the full scale start-up tests. This paper describes the results of power increasing test, test of crash astern propulsion from ahead cruising, and turbine trip test; In the power increasing test, the main steam flow rate increased from 20 % flow to 70 % flow in 13 seconds; In the test of crash astern propulsion from ahead cruising, an astern turbine maneuvering handle was drawn to the position equivalent to about 60 % reactor power in 30 seconds after an ahead turbine stopping; In the turbine trip test, the ahead turbine was tripped manually at about 100 % power operation. From these tests it was verified that the Mutsu reactor is capable to respond smoothly and safely to the heavy load change without reactor scram, without workings of the pressurizer relief valve and main steam dump valve, and without need of any manual adjustment of the reactor control system. (author)

  6. Nonlinear Container Ship Model for the Study of Parametric Roll Resonance

    Holden, Christian; Galeazzi, Roberto; Rodríguez, Claudio

    2007-01-01

    Parametric roll is a critical phenomenon for ships, whose onset may cause roll oscillations up to 40, leading to very dangerous situations and possibly capsizing. Container ships have been shown to be particularly prone to parametric roll resonance when they are sailing in moderate to heavy head ...

  7. DATA MINING METHODOLOGY FOR DETERMINING THE OPTIMAL MODEL OF COST PREDICTION IN SHIP INTERIM PRODUCT ASSEMBLY

    Damir Kolich

    2016-03-01

    Full Text Available In order to accurately predict costs of the thousands of interim products that are assembled in shipyards, it is necessary to use skilled engineers to develop detailed Gantt charts for each interim product separately which takes many hours. It is helpful to develop a prediction tool to estimate the cost of interim products accurately and quickly without the need for skilled engineers. This will drive down shipyard costs and improve competitiveness. Data mining is used extensively for developing prediction models in other industries. Since ships consist of thousands of interim products, it is logical to develop a data mining methodology for a shipyard or any other manufacturing industry where interim products are produced. The methodology involves analysis of existing interim products and data collection. Pre-processing and principal component analysis is done to make the data “user-friendly” for later prediction processing and the development of both accurate and robust models. The support vector machine is demonstrated as the better model when there are a lower number of tuples. However as the number of tuples is increased to over 10000, then the artificial neural network model is recommended.

  8. Ship Routing with Pickup and Delivery for a Maritime Oil Transportation System: MIP Model and Heuristics

    Vinícius P. Rodrigues

    2016-09-01

    Full Text Available This paper examines a ship routing problem with pickup and delivery and time windows for maritime oil transportation, motivated by the production and logistics activities of an oil company operating in the Brazilian coast. The transportation costs from offshore platforms to coastal terminals are an important issue in the search for operational excellence in the oil industry, involving operations that demand agile and effective decision support systems. This paper presents an optimization approach to address this problem, based on a mixed integer programming (MIP model and a novel and exploratory application of two tailor-made MIP heuristics, based on relax-and-fix and time decomposition procedures. The model minimizes fuel costs of a heterogeneous fleet of oil tankers and costs related to freighting contracts. The model also considers company-specific constraints for offshore oil transportation. Computational experiments based on the mathematical models and the related MIP heuristics are presented for a set of real data provided by the company, which confirm the potential of optimization-based methods to find good solutions for problems of moderate sizes.

  9. Influences of variables on ship collision probability in a Bayesian belief network model

    Hänninen, Maria; Kujala, Pentti

    2012-01-01

    The influences of the variables in a Bayesian belief network model for estimating the role of human factors on ship collision probability in the Gulf of Finland are studied for discovering the variables with the largest influences and for examining the validity of the network. The change in the so-called causation probability is examined while observing each state of the network variables and by utilizing sensitivity and mutual information analyses. Changing course in an encounter situation is the most influential variable in the model, followed by variables such as the Officer of the Watch's action, situation assessment, danger detection, personal condition and incapacitation. The least influential variables are the other distractions on bridge, the bridge view, maintenance routines and the officer's fatigue. In general, the methods are found to agree on the order of the model variables although some disagreements arise due to slightly dissimilar approaches to the concept of variable influence. The relative values and the ranking of variables based on the values are discovered to be more valuable than the actual numerical values themselves. Although the most influential variables seem to be plausible, there are some discrepancies between the indicated influences in the model and literature. Thus, improvements are suggested to the network.

  10. The use of long range identification and tracking (LRIT) for modelling the risk of ship-based oil spills

    Szeto, Andrew [Canadian Coast Guard (Canada)], email: andrew.szeto@dfo-mpo.gc.ca; Pelot, Ronald [Dalhousie University (Canada)], email: ronald.pelot@dal.ca

    2011-07-01

    Accidents involving oil tankers have caused many and sometimes very large oil spills. Such spills to marine areas have a significant impact on environmental quality affecting all aspects of marine ecosystems. Based on valid shipping traffic data as a very important factor that must be considered in modeling the risk of ship-based oil spills, this paper shows the importance of use of the long-range identification and tracking (LRIT) system and looks at how it can be implemented to better assess ship-based oil pollution. The system is a new, accurate and reliable world-wide vessel tracking system with a range of data extended out to 1000 nm from Canadian shores and currently tracks up to about 900 vessels a day in real-time. It is believed that traffic data and effective monitoring can assist with search planning for detection of mystery spills, better resource deployment for spill mitigation, and improving information for research and management.

  11. Handbook of nuclear ships

    1981-03-01

    First, the government organs and other organizations related to nuclear ships and their tasks are described. The fundamental plan for the development of nuclear ships had been determined in July, 1963, and was revised three times thereafter. However in December, 1980, new determination to carry out the research works also was made. The course of the construction of the nuclear ship ''Mutsu'' from 1955 to 1980, the main particulars of the nuclear ship ''Mutsu'' and the drawing of the general arrangement are shown. The designated port for berthing the Mutsu was completed in 1972 in Ominato, Aomori Prefecture, but after the happening of radiation leak during the trial operation of the Mutsu in 1974, it was agreed to remove the port. The main works to be carried out at the port and the port facilities are explained. The progress of the examination of safety of the Mutsu and the result, the test of raising the power output carried out in 1974, and the course of selecting the port for making the repair works of the Mutsu are described. The law concerning Japan Nuclear Ship Research and Development Agency had been instituted in 1963, and was revised four times thereafter. The change of the budget for the tests and researches related to nuclear ships in Japan is shown. The state of development of nuclear ships in foreign countries, the international organs related to atomic energy, shipping, shipbuilding and energy, and chronological table are introduced. (Kako, I.)

  12. MODELING OF OPERATION MODES OF SHIP POWER PLANT OF COMBINED PROPULSION COMPLEX WITH CONTROL SYSTEM BASED ON ELECTRONIC CONTROLLERS

    E. A. Yushkov

    2016-12-01

    Full Text Available Purpose. Designing of diagrams to optimize mathematic model of the ship power plant (SPP combined propulsion complexes (CPC for decreasing operational loss and increasing fuel efficiency with simultaneous load limiting on medium revolutions diesel generator (MRDG by criterion reducing of wear and increasing operation time between repairs. Methodology. After analyzing of ship power plant modes of CPC proposed diagrams to optimize mathematic model of the above mentioned complex. The model based on using of electronic controllers in automatic regulation and control systems for diesel and thruster which allow to actualize more complicated control algorithm with viewpoint of increasing working efficiency of ship power plant at normal and emergency modes. Results. Determined suitability of comparative computer modeling in MatLab Simulink for building of imitation model objects based on it block diagrams and mathematic descriptions. Actualized diagrams to optimize mathematic model of the ship’s power plant (SPP combined propulsion complexes (CPC with Azipod system in MatLab Simulink software package Ships_CPC for decreasing operational loss and increasing fuel efficiency with simultaneous load limiting on medium revolutions diesel generator (MRDG by criterion reducing of wear and increasing operation time between repairs. The function blocks of proposed complex are the main structural units which allow to investigate it normal and emergency modes. Originality. This model represents a set of functional blocks of the components SPP CPC, built on the principle of «input-output». For example, the function boxes outputs of PID-regulators of MRDG depends from set excitation voltage and rotating frequency that in turn depends from power-station load and respond that is a ship moving or dynamically positioning, and come on input (inputs of thruster rotating frequency PID-regulator models. Practical value. The results of researches planned to use in

  13. Estimation of waves and ship responses using onboard measurements

    Montazeri, Najmeh

    This thesis focuses on estimation of waves and ship responses using ship-board measurements. This is useful for development of operational safety and performance efficiency in connection with the broader concept of onboard decision support systems. Estimation of sea state is studied using a set...... of measured ship responses, a parametric description of directional wave spectra (a generalised JONSWAP model) and the transfer functions of the ship responses. The difference between the spectral moments of the measured ship responses and the corresponding theoretically calculated moments formulates a cost...... information. The model is tested on simulated data based on known unimodal and bimodal wave scenarios. The wave parameters in the output are then compared with the true wave parameters. In addition to the numerical experiments, two sets of full-scale measurements from container ships are analysed. Herein...

  14. Internal Corrosion Analysis of Model 9975 Packaging Containing Pu or PuO2 During Shipping and Storage

    Vormelker, P.

    1999-01-01

    The Materials Consultation Group of SRTC has completed an internal corrosion analysis of the Model 9975 packaging assembly containing either Pu or PuO2 for storage in K Reactor under ambient conditions for a period of 12 years. The 12-year storage period includes two years for shipping and up to ten years for storage

  15. Review of the total system related to operation of nuclear-powered ship

    Takamasa, Tomoji; Miyashita, Kunio

    2000-01-01

    It is essential to establish a marine reactor having excellent safety and reliability, which is capable of competing economically with conventional ships, and which can be accepted by international society, in order to be prepared for practical application of future nuclear-powered ships. For this purpose, it is important not only to demonstrate a marine reactor using a model or test device to simulate actual operation, but also to establish the environmental requirements for operation of a nuclear-powered ship, such as safety standards that are operationally and internationally common for ships, and to establish a repair base for nuclear-powered ships. Systems research for the practical application of nuclear-powered ships was conducted for five years, fiscal years 1992 through 1996, by a group in the Japan Atomic Energy Research Institute (JAERI), under the project title 'Review of the total system related to operation of nuclear-powered ships.' The project sought to summarize requirements for the practical application of nuclear-powered ships from the standpoint of the need side, e.g., what nuclear-powered ships will be requested, and what functions will be provided under the expected future social environment; to show a complete system concept for the operation of nuclear-powered ships; and to clarify the situations creating demand for nuclear-powered ships, as well as the system and environmental conditions to be established for operation of practical nuclear-powered ships. Study considerations included the size of the operation system for a nuclear-powered ship, a scenario for introducing a nuclear-powered container ship, and economic evolution from the effects on the whole shipping system, based on container ships, of introducing a nuclear-powered ship. The results of these considerations were made the framework for constructing an entire system and evaluating its economy. The treatment and disposal of radioactive waste from a nuclear-powered ship, and the

  16. Radiation Belt Test Model

    Freeman, John W.

    2000-10-01

    Rice University has developed a dynamic model of the Earth's radiation belts based on real-time data driven boundary conditions and full adiabaticity. The Radiation Belt Test Model (RBTM) successfully replicates the major features of storm-time behavior of energetic electrons: sudden commencement induced main phase dropout and recovery phase enhancement. It is the only known model to accomplish the latter. The RBTM shows the extent to which new energetic electrons introduced to the magnetosphere near the geostationary orbit drift inward due to relaxation of the magnetic field. It also shows the effects of substorm related rapid motion of magnetotail field lines for which the 3rd adiabatic invariant is violated. The radial extent of this violation is seen to be sharply delineated to a region outside of 5Re, although this distance is determined by the Hilmer-Voigt magnetic field model used by the RBTM. The RBTM appears to provide an excellent platform on which to build parameterized refinements to compensate for unknown acceleration processes inside 5Re where adiabaticity is seen to hold. Moreover, built within the framework of the MSFM, it offers the prospect of an operational forecast model for MeV electrons.

  17. Temporal modelling of ballast water discharge and ship-mediated invasion risk to Australia.

    Cope, Robert C; Prowse, Thomas A A; Ross, Joshua V; Wittmann, Talia A; Cassey, Phillip

    2015-04-01

    Biological invasions have the potential to cause extensive ecological and economic damage. Maritime trade facilitates biological invasions by transferring species in ballast water, and on ships' hulls. With volumes of maritime trade increasing globally, efforts to prevent these biological invasions are of significant importance. Both the International Maritime Organization and the Australian government have developed policy seeking to reduce the risk of these invasions. In this study, we constructed models for the transfer of ballast water into Australian waters, based on historic ballast survey data. We used these models to hindcast ballast water discharge over all vessels that arrived in Australian waters between 1999 and 2012. We used models for propagule survival to compare the risk of ballast-mediated propagule transport between ecoregions. We found that total annual ballast discharge volume into Australia more than doubled over the study period, with the vast majority of ballast water discharge and propagule pressure associated with bulk carrier traffic. As such, the ecoregions suffering the greatest risk are those associated with the export of mining commodities. As global marine trade continues to increase, effective monitoring and biosecurity policy will remain necessary to combat the risk of future marine invasion events.

  18. Shipping Fairways

    Department of Homeland Security — Various shipping zones delineate activities and regulations for marine vessel traffic. Traffic lanes define specific traffic flow, while traffic separation zones...

  19. Green vessel scheduling in liner shipping: Modeling carbon dioxide emission costs in sea and at ports of call

    Maxim A. Dulebenets

    2018-03-01

    Full Text Available Considering a substantial increase in volumes of the international seaborne trade and drastic climate changes due to carbon dioxide emissions, liner shipping companies have to improve planning of their vessel schedules and improve energy efficiency. This paper presents a novel mixed integer non-linear mathematical model for the green vessel scheduling problem, which directly accounts for the carbon dioxide emission costs in sea and at ports of call. The original non-linear model is linearized and then solved using CPLEX. A set of numerical experiments are conducted for a real-life liner shipping route to reveal managerial insights that can be of importance to liner shipping companies. Results indicate that the proposed mathematical model can serve as an efficient planning tool for liner shipping companies and may assist with evaluation of various carbon dioxide taxation schemes. Increasing carbon dioxide tax may substantially change the design of vessel schedules, incur additional route service costs, and improve the environmental sustainability. However, the effects from increasing carbon dioxide tax on the marine container terminal operations are found to be very limited.

  20. Validation through model testing

    1995-01-01

    Geoval-94 is the third Geoval symposium arranged jointly by the OECD/NEA and the Swedish Nuclear Power Inspectorate. Earlier symposia in this series took place in 1987 and 1990. In many countries, the ongoing programmes to site and construct deep geological repositories for high and intermediate level nuclear waste are close to realization. A number of studies demonstrates the potential barrier function of the geosphere, but also that there are many unresolved issues. A key to these problems are the possibilities to gain knowledge by model testing with experiments and to increase confidence in models used for prediction. The sessions cover conclusions from the INTRAVAL-project, experiences from integrated experimental programs and underground research laboratories as well as the integration between performance assessment and site characterisation. Technical issues ranging from waste and buffer interactions with the rock to radionuclide migration in different geological media is addressed. (J.S.)

  1. Developing a Risk Model for Fire in Passenger Ships - Based on Bayesian Belief Network

    Dokmo, Hanne Bjørkås

    2016-01-01

    Passenger ships, especially cruise ships, are rapidly increasing in size. With larger vessels, comes a greater risk to the passengers if something where to happen. A fire on a passenger vessel can spread quickly, and with as much as thousands of people needing to be evacuated many things could go wrong. The issue of the safety on board is therefore crucial to consider, seeing as the consequences could be tremendous. There are three types of passenger ships; Passenger vessel, RoPax vessel and ...

  2. Test report for PAS-1 cask certification for shipping payload B

    MERCADO, J.E.

    1998-01-01

    This test report documents the successful inspection and testing to certify two NuPac PAS-1 casks in accordance with US Department of Energy Certificate of Compliance (CoC) USA/9184/B(U). The primary and secondary containment vessels of each cask met the acceptance criteria defined in the CoC and the test plan

  3. Surveying, Modeling and 3d Representation of a wreck for Diving Purposes: Cargo Ship "vera"

    Ktistis, A.; Tokmakidis, P.; Papadimitriou, K.

    2017-02-01

    This paper presents the results from an underwater recording of the stern part of a contemporary cargo-ship wreck. The aim of this survey was to create 3D representations of this wreck mainly for recreational diving purposes. The key points of this paper are: a) the implementation of the underwater recording at a diving site; b) the reconstruction of a 3d model from data that have been captured by recreational divers; and c) the development of a set of products to be used by the general public for the ex situ presentation or for the in situ navigation. The idea behind this project is to define a simple and low cost procedure for the surveying, modeling and 3D representation of a diving site. The perspective of our team is to repeat the proposed methodology for the documentation and the promotion of other diving sites with cultural features, as well as to train recreational divers in underwater surveying procedures towards public awareness and community engagement in the maritime heritage.

  4. Ship nonlinear-feedback course keeping algorithm based on MMG model driven by bipolar sigmoid function for berthing

    Qiang Zhang

    2017-09-01

    Full Text Available Course keeping is hard to implement under the condition of the propeller stopping or reversing at slow speed for berthing due to the ship's dynamic motion becoming highly nonlinear. To solve this problem, a practical Maneuvering Modeling Group (MMG ship mathematic model with propeller reversing transverse forces and low speed correction is first discussed to be applied for the right-handed single-screw ship. Secondly, a novel PID-based nonlinear feedback algorithm driven by bipolar sigmoid function is proposed. The PID parameters are determined by a closed-loop gain shaping algorithm directly, while the closed-loop gain shaping theory was employed for effects analysis of this algorithm. Finally, simulation experiments were carried out on an LPG ship. It is shown that the energy consumption and the smoothness performance of the nonlinear feedback control are reduced by 4.2% and 14.6% with satisfactory control effects; the proposed algorithm has the advantages of robustness, energy saving and safety in berthing practice.

  5. Pitch control for ships with diesel mechanical and hybrid propulsion : Modelling, validation and performance quantification

    Geertsma, R.D.; Negenborn, R.R.; Visser, K.; Loonstijn, M.A.; Hopman, J.J.

    2017-01-01

    Ships, in particular service vessels, need to reduce fuel consumption, emissions and cavitation noise while maintaining manoeuvrability and preventing engine overloading. Diesel mechanical propulsion with controllable pitch propellers can provide high fuel efficiency with good manoeuvrability.

  6. Modelling and developing a decision-making process of hazard zone identification in ship power plants

    Podsiadlo, Antoni; Tarelko, Wieslaw

    2006-01-01

    The most dangerous places in ships are their power plants. Particularly, they are very unsafe for operators carried out various necessary operation and maintenance activities. For this reason, ship machinery should be designed to ensure the maximum safety for its operators. It is a very difficult task. Therefore, it could not be solved by means of conventional design methods, which are used for design of uncomplicated technical equipment. One of the possible ways of solving this problem is to provide appropriate tools, which allow us to take the operator's safety into account during a design process, especially at its early stages. A computer-aided system supporting design of safe ship power plants could be such a tool. This paper deals with developing process of a prototype of the computer-aided system for hazard zone identification in ship power plants

  7. Modelling and developing a decision-making process of hazard zone identification in ship power plants

    Podsiadlo, Antoni [Department of Engineering Sciences, Gdynia Maritime University, ul. Morska 83, 81-225 Gdynia (Poland)]. E-mail: topo@am.gdynia.pl; Tarelko, Wieslaw [Department of Engineering Sciences, Gdynia Maritime University, ul. Morska 83, 81-225 Gdynia (Poland)]. E-mail: tar@am.gdynia.pl

    2006-04-15

    The most dangerous places in ships are their power plants. Particularly, they are very unsafe for operators carried out various necessary operation and maintenance activities. For this reason, ship machinery should be designed to ensure the maximum safety for its operators. It is a very difficult task. Therefore, it could not be solved by means of conventional design methods, which are used for design of uncomplicated technical equipment. One of the possible ways of solving this problem is to provide appropriate tools, which allow us to take the operator's safety into account during a design process, especially at its early stages. A computer-aided system supporting design of safe ship power plants could be such a tool. This paper deals with developing process of a prototype of the computer-aided system for hazard zone identification in ship power plants.

  8. Risk of Cyberterrorism to Naval Ships Inport Naval Station Everett: A Model Based Project Utilizing SIAM

    Tester, Rodrick A

    2007-01-01

    Based on numerous high level concerns that the cyber threat is expected to increase, as well as the already documented uses of cyber warfare, it is necessary to ensure our naval ships are hardened against such attacks...

  9. A path based model for a green liner shipping network design problem

    Jepsen, Mads Kehlet; Brouer, Berit Dangaard; Plum, Christian Edinger Munk

    2011-01-01

    Liner shipping networks are the backbone of international trade providing low transportation cost, which is a major driver of globalization. These networks are under constant pressure to deliver capacity, cost effectiveness and environmentally conscious transport solutions. This article proposes...

  10. Ship Vibrations

    Sørensen, Herman

    1997-01-01

    Methods for calculating natural frequencies for ship hulls and for plates and panels.Evaluation of the risk for inconvenient vibrations on board......Methods for calculating natural frequencies for ship hulls and for plates and panels.Evaluation of the risk for inconvenient vibrations on board...

  11. An investigation of forecast horizon and observation fit’s influence on an econometric rate forecast model in the liner shipping industry

    Nielsen, Peter; Jiang, Liping; Rytter, Niels Gorm Malý

    2014-01-01

    This paper evaluates the influence of forecast horizon and observation fit on the robustness and performance of a specific freight rate forecast model used in the liner shipping industry. In the first stage of the research, a forecast model used to predict container freight rate development...... of the forecast horizon and observation fit and their interactions on the forecast model's performance. The results underline the complicated nature of creating a suitable forecast model by balancing business needs, a desire to fit a good model and achieve high accuracy. There is strong empirical evidence from...... this study; that a robust model is preferable, that overfitting is a true danger, and that a balance must be achieved between forecast horizon and the number of observations used to fit the model. In addition, methodological guidance has also been provided on how to test, design, and choose the superior...

  12. Linking Combat Systems Capabilities and Ship Design Through Modeling and Computer Simulation

    2013-09-01

    consumption (SFC), (4) weight of the power plant , and (5) weight capacity of cargo carrying capacity. The L/D Ratio reflects the amount of...ship. The SFC measures the efficiency of the ship in burning its fuel. The weight of the power reflects the combined weight of fuel and the power plant ... Montenegro Kotor class 1 18000 18000 27 4188800 Taiwan PSO 2 19850 39700 24 4640800 Spain Meteoro class 2 12000 24000 20.5 6261200 Colombia PSO 2

  13. Safety analysis report for packaging: neutron shipping cask, model 0.5T

    Peterson, R.T.

    1976-01-01

    The Safety Analysis Report for Packaging demonstrates that the neutron shipping cask can safely transport, in solid or powder form, all isotopes of uranium, plutonium, americium, curium, berkelium, californium, einsteinium, and fermium. The shipping cask and its contents are described. It also evaluates transport conditions, structural parameters (e.g., load resistance, pressure and impact effects, lifting and tiedown devices), and shielding. Finally, it discusses compliance with Chapter 0529 of the Energy Research and Development Administration Manual

  14. IMPAC-2, Dynamic Impact Analysis for 1-D Nonlinear Spring Shipping Container Model

    Payne, J. B.; Counts, J.

    1980-01-01

    1 - Description of problem or function: IMPAC2 solves the equations of motion for a one-dimensional, lumped-mass, nonlinear spring mathematical container model. The program was designed to analyze the dynamic response of metallic shipping containers impacting an unyielding surface. The container may consist of several hollow concentric cylinders, each of a different material and length. 2 - Method of solution: An iteration technique (Newmark-Beta) is used to solve the equations of motion for displacement, velocity, and acceleration of the masses at each time-step. 3 - Restrictions on the complexity of the problem: The maximum number of masses is 100. The program is written for a maximum of 10 different materials. The first seven have been given the following designations: 1 steel, 2 clad lead, 3 uranium, 4 pine, 5 lead, 6 balsa, 7 marine plywood. Stress-strain characteristics for materials 1, 3, 4, and 6 are approximated by a bilinear curve fit which requires as input the modulus of elasticity, the stress at the intersection of the two lines and the slope of the second line

  15. Recreating the shading effects of ship wake induced turbidity to test acclimation responses in the seagrass Thalassia hemprichii

    Browne, Nicola K.; Yaakub, Siti Maryam; Tay, Jason K. L.; Todd, Peter A.

    2017-12-01

    Elevated sediment delivery and resuspension in coastal waters from human activities such as shipping can have detrimental effects on seagrass health by limiting light penetration. Managing seagrasses requires knowledge of their light acclamatory abilities so guidelines for coastal activities (e.g. ship movements) that influence sediment dynamics can be created. Guidelines typically focus on ensuring that seagrasses are able to meet their minimal light requirements (MLR). MLRs can be achieved by different light regimes, but it remains unknown whether a chronically low yet stable light regime is less or more detrimental than a highly variable regime with periods of extreme low to no light. To test this, we compared the physiological and morphological responses of Thalassia hemprichii among three light regimes: an open control (30-40% ambient light), a shaded control with (11-15% ambient light), and a fluctuating shade (4-30% ambient light). The MLR for the T. hemprichii we studied was lower (4-10% ambient light) than previous reports (mean = 18%) illustrating enhanced light acclimation in Singapore's chronically turbid waters. Seagrass shoots in the shaded control, however, exhibited significantly more morphological stress symptoms, with reduced shoot growth and lower below ground biomass. These data suggest that for seagrass exposed to periods of acute light stress, energetic costs associated with photo-acclimation to more variable light regimes can be offset if the plant can meet its daily light requirements during periods of high light. Management of seagrass beds should incorporate regular light monitoring and move towards an adaptive feedback-based approach to ensure the long-term viability of these vulnerable ecosystems.

  16. a Novel Ship Detection Method for Large-Scale Optical Satellite Images Based on Visual Lbp Feature and Visual Attention Model

    Haigang, Sui; Zhina, Song

    2016-06-01

    Reliably ship detection in optical satellite images has a wide application in both military and civil fields. However, this problem is very difficult in complex backgrounds, such as waves, clouds, and small islands. Aiming at these issues, this paper explores an automatic and robust model for ship detection in large-scale optical satellite images, which relies on detecting statistical signatures of ship targets, in terms of biologically-inspired visual features. This model first selects salient candidate regions across large-scale images by using a mechanism based on biologically-inspired visual features, combined with visual attention model with local binary pattern (CVLBP). Different from traditional studies, the proposed algorithm is high-speed and helpful to focus on the suspected ship areas avoiding the separation step of land and sea. Largearea images are cut into small image chips and analyzed in two complementary ways: Sparse saliency using visual attention model and detail signatures using LBP features, thus accordant with sparseness of ship distribution on images. Then these features are employed to classify each chip as containing ship targets or not, using a support vector machine (SVM). After getting the suspicious areas, there are still some false alarms such as microwaves and small ribbon clouds, thus simple shape and texture analysis are adopted to distinguish between ships and nonships in suspicious areas. Experimental results show the proposed method is insensitive to waves, clouds, illumination and ship size.

  17. Second Annual Maintenance, Inspection, and Test Report for PAS-1 Cask Certification for Shipping Payload B

    KELLY, D.J.

    2000-01-01

    The Nuclear Packaging, Inc. (NuPac), PAS-1 cask is required to undergo annual maintenance and inspections to retain certification in accordance with U.S. Department of Energy (DOE) Certificate of Compliance USA/9184B(U) (Appendix A). The packaging configuration being tested and maintained is the NuPac PAS-1 cask for Payload B. The intent of the maintenance and inspections is to ensure the packaging remains in unimpaired physical condition. Two casks, serial numbers 2162-026 and 2162-027, were maintained, inspected, and tested at the 306E Development, Fabrication, and Test Laboratory, located at the Hanford Site's 300 Area. Waste Management Federal Services, Inc. (WMFS), a subsidiary of GTS Duratek, was in charge of the maintenance and testing. Cogema Engineering Corporation (Cogema) directed the operations in the test facility. The maintenance, testing, and inspections were conducted successfully with both PAS-1 casks. The work conducted on the overpacks included weighing, gasket replacement, and plastic pipe plug and foam inspections. The work conducted on the secondary containment vessel (SCV) consisted of visual inspection of the vessel and threaded parts (i.e., fasteners), visual inspection of sealing surfaces, replacement of O-ring seals, and a helium leak test. The work conducted on the primary containment vessel (PCV) consisted of visual inspection of the vessel and threaded parts (i.e., fasteners), visual inspection of sealing surfaces, replacement of O-ring seals, dimensional inspection of the vessel bottom, a helium leak test, and dye penetrant inspection of the welds. The vermiculite material used in the cask rack assembly was replaced

  18. Extended testing of a modified 18B plutonium nitrate shipping container

    Yoshimura, H.R.; Pope, R.B.; Leisher, W.B.; Joseph, B.J.; Schulz-Forberg, B.; Hubner, H.W.

    1980-01-01

    The container damage observed as the result of the high-speed pulldown impact test was more severe than that of either the 185-m free-fall drop of a prototype container onto a semirigid surface or the crush environment produced by a 9-m drop of a 2-tonne block onto a modified container resting on an unyielding surface. In comparison to the extended tests, the 9-m regulatory drop test onto an unyielding surface of the prototype packaging in its most damaging orientation produced the least amount of damage. Very little deformation in the overpack was observed, and there was no influence on the fire resistivity and leaktightness of the containment vessel. The 128 m/s impact test produced a leak in the container. It appears that the 18B packaging, designed to withstand the environments specified in IAEA Safety Series No. 6, can withstand extended environments including longer duration fires and higher velocity impacts on yielding targets. When modified with ring stiffeners, the packaging withstood a dynamic crush test, but did not survive the high speed impact onto an unyielding surface as specified in NUREG 0360

  19. Towards Real Time Simulation of Ship-Ship Interaction

    Lindberg, Ole; Bingham, Harry B.; Engsig-Karup, Allan Peter

    2012-01-01

    We present recent and preliminary work directed towards the development of a simplified, physics-based model for improved simulation of ship-ship interaction that can be used for both analysis and real-time computing (i.e. with real-time constraints due to visualization). The goal is to implement...... accurate (realistic) and much faster ship-wave and ship-ship simulations than are currently possible. The coupling of simulation with visualization should improve the visual experience such that it can be perceived as more realistic in training. Today the state-of-art in real-time ship-ship interaction...... is for efficiency reasons and time-constraints in visualization based on model experiments in towing tanks and precomputed force tables. We anticipate that the fast, and highly parallel, algorithm described by Engsig-Karup et al. [2011] for execution on affordable modern high-throughput Graphics Processing Units...

  20. The beam test of muon detector parameters for the SHiP experiment at CERN

    Likhacheva, V. L.; Kudenko, Yu. G.; Mefodiev, A. V.; Mineev, O. V.; Khotyantsev, A. N.

    2018-01-01

    Scintillation detectors based on extruded plastics have been tested in a 10 GeV/c beam at CERN. The scintillation signal readout was provided using optical wavelength shifting fibers Y11 Kuraray and Hamamatsu MPPC micropixel avalanche photodiodes. The light yield was scanned along and across the detectors. Time resolution was found by fitting the MPPC digitized pulse rise and other methods.

  1. Global model simulations of the impact of ocean-going ships on aerosols, clouds, and the radiation budget

    A. Lauer

    2007-10-01

    Full Text Available International shipping contributes significantly to the fuel consumption of all transport related activities. Specific emissions of pollutants such as sulfur dioxide (SO2 per kg of fuel emitted are higher than for road transport or aviation. Besides gaseous pollutants, ships also emit various types of particulate matter. The aerosol impacts the Earth's radiation budget directly by scattering and absorbing the solar and thermal radiation and indirectly by changing cloud properties. Here we use ECHAM5/MESSy1-MADE, a global climate model with detailed aerosol and cloud microphysics to study the climate impacts of international shipping. The simulations show that emissions from ships significantly increase the cloud droplet number concentration of low marine water clouds by up to 5% to 30% depending on the ship emission inventory and the geographic region. Whereas the cloud liquid water content remains nearly unchanged in these simulations, effective radii of cloud droplets decrease, leading to cloud optical thickness increase of up to 5–10%. The sensitivity of the results is estimated by using three different emission inventories for present-day conditions. The sensitivity analysis reveals that shipping contributes to 2.3% to 3.6% of the total sulfate burden and 0.4% to 1.4% to the total black carbon burden in the year 2000 on the global mean. In addition to changes in aerosol chemical composition, shipping increases the aerosol number concentration, e.g. up to 25% in the size range of the accumulation mode (typically >0.1 μm over the Atlantic. The total aerosol optical thickness over the Indian Ocean, the Gulf of Mexico and the Northeastern Pacific increases by up to 8–10% depending on the emission inventory. Changes in aerosol optical thickness caused by shipping induced modification of aerosol particle number concentration and chemical composition lead to a change in the shortwave radiation budget at the top of the

  2. PTM Modeling of Dredged Suspended Sediment at Proposed Polaris Point and Ship Repair Facility CVN Berthing Sites - Apra Harbor, Guam

    2017-09-01

    sedimentation outside of the channel footprint. For example, dredging near the edge of the footprint can be confined to time periods when tidal currents...Cases 1 or 2 due to the lower loss rate. Sedimentation rates outside the channel prism are further reduced because all sediment is introduced in the...ER D C/ CH L TR -1 7- 16 PTM Modeling of Dredged Suspended Sediment at Proposed Polaris Point and Ship Repair Facility CVN Berthing

  3. Modeling the energy content of combustible ship-scrapping waste at Alang-Sosiya, India, using multiple regression analysis.

    Reddy, M Srinivasa; Basha, Shaik; Joshi, H V; Sravan Kumar, V G; Jha, B; Ghosh, P K

    2005-01-01

    Alang-Sosiya is the largest ship-scrapping yard in the world, established in 1982. Every year an average of 171 ships having a mean weight of 2.10 x 10(6)(+/-7.82 x 10(5)) of light dead weight tonnage (LDT) being scrapped. Apart from scrapped metals, this yard generates a massive amount of combustible solid waste in the form of waste wood, plastic, insulation material, paper, glass wool, thermocol pieces (polyurethane foam material), sponge, oiled rope, cotton waste, rubber, etc. In this study multiple regression analysis was used to develop predictive models for energy content of combustible ship-scrapping solid wastes. The scope of work comprised qualitative and quantitative estimation of solid waste samples and performing a sequential selection procedure for isolating variables. Three regression models were developed to correlate the energy content (net calorific values (LHV)) with variables derived from material composition, proximate and ultimate analyses. The performance of these models for this particular waste complies well with the equations developed by other researchers (Dulong, Steuer, Scheurer-Kestner and Bento's) for estimating energy content of municipal solid waste.

  4. Distributed propulsion for ships

    Nylund, Vilde

    2017-01-01

    It is anticipated that using distributed electric propulsion (DEP) on conventional ships will increase the total propulsive efficiency. This is mainly due to two reasons; firstly, because the total propeller disk area can be increased. Secondly, because each propeller can be optimised for the local wake where it is operating. In this work, the benefits of using DEP has been investigated for a 14 000 TEU container ship. Based on a literary study of the present state of propeller modelling ...

  5. ERDC Ship/Tow Simulator

    Federal Laboratory Consortium — Performing Advanced Hydrodynamic ModelingEngineers and ship pilots can now overcome the challenges of evaluating navigation channel designs, modifications and safety...

  6. Modeling Liner Shipping Service Selection and Container Flows using a Multi-layer Network

    Karsten, Christian Vad; Balakrishnan, Anant

    We introduce a new formulation for the tactical planning problem facing container shipping companies of selecting the best subset of sailing routes from a given pool of candidate routes so as to maximize profit. Since most containers are sent directly or transshipped at most twice in current liner...

  7. Shipping and shipbuilding scenario evaluations through integration of maritime and macroeconomic models

    Pruyn, J.F.J.

    2013-01-01

    This research focusses on the use of consistent scenarios to help ship owners, banks and other parties with an interest the maritime business get a better grip on the future. Three levels of detail can be distinguished for the maritime industry. The macroeconomic level is the highest and focusses on

  8. Importance of Ship Emissions to Local Summertime Ozone Production in the Mediterranean Marine Boundary Layer: A Modeling Study

    Christian N. Gencarelli

    2014-12-01

    Full Text Available Ozone concentrations in the Mediterranean area regularly exceed the maximum levels set by the EU Air Quality Directive, 2008/50/CE, a maximum 8-h mean of 120 μg·m-3, in the summer, with consequences for both human health and agriculture. There are a number of reasons for this: the particular geographical and meteorological conditions in the Mediterranean play a part, as do anthropogenic ozone precursor emissions from around the Mediterranean and continental Europe. Ozone concentrations measured on-board the Italian Research Council’s R. V. Urania during summer oceanographic campaigns between 2000 and 2010 regularly exceeded 60 ppb, even at night. The WRF/Chem (Weather Research and Forecasting (WRF model coupled with Chemistrymodel has been used to simulate tropospheric chemistry during the periods of the measurement campaigns, and then, the same simulations were repeated, excluding the contribution of maritime traffic in the Mediterranean to the anthropogenic emissions inventory. The differences in the model output suggest that, in large parts of the coastal zone of the Mediterranean, ship emissions Atmosphere 2014, 5 938 contribute to 3 and 12 ppb to ground level daily average ozone concentrations. Near busy shipping lanes, up to 40 ppb differences in the hourly average ozone concentrations were found. It seems that ship emissions could be a significant factor in the exceedance of the EU directive on air quality in large areas of the Mediterranean Basin.

  9. Optimization in liner shipping

    Brouer, Berit Dangaard; Karsten, Christian Vad; Pisinger, David

    2017-01-01

    Seaborne trade is the lynchpin in almost every international supply chain, and about 90% of non-bulk cargo worldwide is transported by container. In this survey we give an overview of data-driven optimization problems in liner shipping. Research in liner shipping is motivated by a need for handling...... still more complex decision problems, based on big data sets and going across several organizational entities. Moreover, liner shipping optimization problems are pushing the limits of optimization methods, creating a new breeding ground for advanced modelling and solution methods. Starting from liner...... shipping network design, we consider the problem of container routing and speed optimization. Next, we consider empty container repositioning and stowage planning as well as disruption management. In addition, the problem of bunker purchasing is considered in depth. In each section we give a clear problem...

  10. Time constrained liner shipping network design

    Karsten, Christian Vad; Brouer, Berit Dangaard; Desaulniers, Guy

    2017-01-01

    We present a mathematical model and a solution method for the liner shipping network design problem. The model takes into account coordination between vessels and transit time restrictions on the cargo flow. The solution method is an improvement heuristic, where an integer program is solved...... iteratively to perform moves in a large neighborhood search. Our improvement heuristic is applicable as a real-time decision support tool for a liner shipping company. It can be used to find improvements to the network when evaluating changes in operating conditions or testing different scenarios...

  11. Sensitivity Analysis for Iceberg Geometry Shape in Ship-Iceberg Collision in View of Different Material Models

    Yan Gao

    2014-01-01

    Full Text Available The increasing marine activities in Arctic area have brought growing interest in ship-iceberg collision study. The purpose of this paper is to study the iceberg geometry shape effect on the collision process. In order to estimate the sensitivity parameter, five different geometry iceberg models and two iceberg material models are adopted in the analysis. The FEM numerical simulation is used to predict the scenario and the related responses. The simulation results including energy dissipation and impact force are investigated and compared. It is shown that the collision process and energy dissipation are more sensitive to iceberg local shape than other factors when the elastic-plastic iceberg material model is applied. The blunt iceberg models act rigidly while the sharp ones crush easily during the simulation process. With respect to the crushable foam iceberg material model, the iceberg geometry has relatively small influence on the collision process. The spherical iceberg model shows the most rigidity for both iceberg material models and should be paid the most attention for ice-resist design for ships.

  12. AUTOCASK (AUTOmatic Generation of 3-D CASK models). A microcomputer based system for shipping cask design review analysis

    Gerhard, M.A.; Sommer, S.C.

    1995-04-01

    AUTOCASK (AUTOmatic Generation of 3-D CASK models) is a microcomputer-based system of computer programs and databases developed at the Lawrence Livermore National Laboratory (LLNL) for the structural analysis of shipping casks for radioactive material. Model specification is performed on the microcomputer, and the analyses are performed on an engineering workstation or mainframe computer. AUTOCASK is based on 80386/80486 compatible microcomputers. The system is composed of a series of menus, input programs, display programs, a mesh generation program, and archive programs. All data is entered through fill-in-the-blank input screens that contain descriptive data requests

  13. AUTOCASK (AUTOmatic Generation of 3-D CASK models). A microcomputer based system for shipping cask design review analysis

    Gerhard, M.A.; Sommer, S.C. [Lawrence Livermore National Lab., CA (United States)

    1995-04-01

    AUTOCASK (AUTOmatic Generation of 3-D CASK models) is a microcomputer-based system of computer programs and databases developed at the Lawrence Livermore National Laboratory (LLNL) for the structural analysis of shipping casks for radioactive material. Model specification is performed on the microcomputer, and the analyses are performed on an engineering workstation or mainframe computer. AUTOCASK is based on 80386/80486 compatible microcomputers. The system is composed of a series of menus, input programs, display programs, a mesh generation program, and archive programs. All data is entered through fill-in-the-blank input screens that contain descriptive data requests.

  14. Fast ship

    Keuning, J.A.

    2014-01-01

    The invention concerns a ship whereby the hull and the mechanical propulsion device are designed such that the Froude number is larger than 0.5. In the aft ship the hull has a bottom with V-shaped bottom surfaces with a deadrise angle that is less than 40 degrees and the hull has substantially vertical sides. In the hull are a passenger compartment and a trim tank. The trim tank volume is such that the weight of a filled trim tank is more than 30 % of the weight of displacement of the hull wi...

  15. Pitch control for ships with diesel mechanical and hybrid propulsion: Modelling, validation and performance quantification

    Geertsma, R.D.; Negenborn, R.R.; Visser, K.; Loonstijn, M.A.; Hopman, J.J.

    2017-01-01

    Ships, in particular service vessels, need to reduce fuel consumption, emissions and cavitation noise while maintaining manoeuvrability and preventing engine overloading. Diesel mechanical propulsion with controllable pitch propellers can provide high fuel efficiency with good manoeuvrability. However, the conventional control strategy with fixed combinator curves limits control freedom in trading-off performance characteristics. In order to evaluate performance of current state-of-the-art an...

  16. Modelling the Dynamics of Ships with Different Propulsion Systems for Control Purpose

    Gierusz Witold

    2016-01-01

    Full Text Available Two different propulsion systems are analyzed from point of view of future control applications. The traditional one consists of a pushing single screw propeller and a blade rudder. The other system is based on pod (pods: pulling or pushing ones. The equations describing forces and moments generated in both systems, are presented. Exemplary results of a simulation in comparison to the real-time experiments for two ships are also shown.

  17. Modeling of Ship Roll Dynamics and Its Coupling with Heave and Pitch

    R. A. Ibrahim

    2010-01-01

    Full Text Available In order to study the dynamic behavior of ships navigating in severe environmental conditions it is imperative to develop their governing equations of motion taking into account the inherent nonlinearity of large-amplitude ship motion. The purpose of this paper is to present the coupled nonlinear equations of motion in heave, roll, and pitch based on physical grounds. The ingredients of the formulation are comprised of three main components. These are the inertia forces and moments, restoring forces and moments, and damping forces and moments with an emphasis to the roll damping moment. In the formulation of the restoring forces and moments, the influence of large-amplitude ship motions will be considered together with ocean wave loads. The special cases of coupled roll-pitch and purely roll equations of motion are obtained from the general formulation. The paper includes an assessment of roll stochastic stability and probabilistic approaches used to estimate the probability of capsizing and parameter identification.

  18. A fuel response model for the design of spent fuel shipping casks

    Malinauskas, A.P.; Duffey, T.A.; Einziger, R.E.; Hobbins, R.R.; Jordon, H.; Rashid, Y.R.; Barrett, P.R.; Sanders, T.L.

    1989-01-01

    The radiological source terms pertinent to spent fuel shipping cask safety assessments are of three distinct origins. One of these concerns residual contamination within the cask due to handling operations and previous shipments. A second is associated with debris (''crud'') that had been deposited on the fuel rods in the course of reactor operation, and a third involves the radioactive material contained within the rods. Although the lattermost source of radiotoxic material overwhelms the others in terms of inventory, its release into the shipping cask, and thence into the biosphere, requires the breach of an additional release barrier, viz., the fuel rod cladding. Hence, except for the special case involving the transport of fuel rods containing previously breached claddings, considerations of the source terms due to material contained in the fuel rods are complicated by the need to address the likelihood of fuel cladding failure during transport. The purpose of this report is to describe a methodology for estimating the shipping cask source terms contribution due to radioactive material contained within the spent fuel rods. Thus, the probability of fuel cladding failure as well as radioactivity release is addressed. 8 refs., 2 tabs

  19. Model-based security testing

    Schieferdecker, Ina; Großmann, Jürgen; Schneider, Martin

    2012-01-01

    Security testing aims at validating software system requirements related to security properties like confidentiality, integrity, authentication, authorization, availability, and non-repudiation. Although security testing techniques are available for many years, there has been little approaches that allow for specification of test cases at a higher level of abstraction, for enabling guidance on test identification and specification as well as for automated test generation. Model-based security...

  20. Model-Based Security Testing

    Ina Schieferdecker

    2012-02-01

    Full Text Available Security testing aims at validating software system requirements related to security properties like confidentiality, integrity, authentication, authorization, availability, and non-repudiation. Although security testing techniques are available for many years, there has been little approaches that allow for specification of test cases at a higher level of abstraction, for enabling guidance on test identification and specification as well as for automated test generation. Model-based security testing (MBST is a relatively new field and especially dedicated to the systematic and efficient specification and documentation of security test objectives, security test cases and test suites, as well as to their automated or semi-automated generation. In particular, the combination of security modelling and test generation approaches is still a challenge in research and of high interest for industrial applications. MBST includes e.g. security functional testing, model-based fuzzing, risk- and threat-oriented testing, and the usage of security test patterns. This paper provides a survey on MBST techniques and the related models as well as samples of new methods and tools that are under development in the European ITEA2-project DIAMONDS.

  1. Mechanics of Ship Grounding

    Pedersen, Preben Terndrup

    1996-01-01

    In these notes first a simplified mathematical model is presented for analysis of ship hull loading due to grounding on relatively hard and plane sand, clay or rock sea bottoms. In a second section a more rational calculation model is described for the sea bed soil reaction forces on the sea bott...

  2. Dynamic modelling of check valves in shipping terminals; Modelagem dinamica de valvulas de retencao em terminais maritimos

    Pires, Luis F.G.; Barreto, Claudio V.; Sarmento, Renata C. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Mecanica. Nucleo de Simulacao Termohidraulica de Dutos (SIMDUT)

    2005-07-01

    As usual a shipping terminal contains a header and its diameter is smaller than the main pipeline diameter. This diameter reduction amplifies the effects caused by hydraulic transients. It was noticed during simulations that check valves without dynamic modeling may introduce some error in the maximum pressure results without a dynamic model approach. The current paper uses commercial pipeline simulation software to model the dynamic behavior of the check valves. It was studied the header diameter influence and how the check valve model type may change the maximum pressure in the pipeline. It was proved that even a pipeline that works with low pressure and small elevation drop needs a detailed valve modeling to prevent the calculation of unreal pressure values in the region with diameter reduction. (author)

  3. Environmental modeling to support Elizio Leao ship rescue operation; Modelagem atmosferica e hidrodinamica em apoio a operacao de resgate da embarcacao Elizio Leao

    Torres Junior, Audalio R. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Lab. de Modelagem de Processos Marinhos e Atmosfericos (LAMMA); Silva, Mariana P.R.; Silva, Ricardo M. da; Assad, Luiz Paulo de F.; Decco, Hatsue T. de; Landau, Luiz [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Lab. de Metodos Computacinais em Engenharia (LAMCE); Silva Junior, Ronaldo da [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2008-07-01

    On October 7th, 2007, the Elizio Leao ship broke carrying 19,812.9 gallons of oil near the Marajo Island has mobilized the PIATAM Mar (Potenciais Impactos do Transporte de Petroleo e Derivados na Zona Costeira Amazonica) modeling team for an execution of hydrodynamic and atmospheric prognostics that could support the ship rescue operation. In this work some results are presented as the operational methodology which has been applied to support the rescue team's needs. (author)

  4. SURVEYING, MODELING AND 3D REPRESENTATION OF A WRECK FOR DIVING PURPOSES: CARGO SHIP “VERA”

    Ktistis, A.; Tokmakidis, P.; Papadimitriou, K.

    2017-01-01

    This paper presents the results from an underwater recording of the stern part of a contemporary cargo-ship wreck. The aim of this survey was to create 3D representations of this wreck mainly for recreational diving purposes. The key points of this paper are: a) the implementation of the underwater recording at a diving site; b) the reconstruction of a 3d model from data that have been captured by recreational divers; and c) the development of a set of products to be used by the general publi...

  5. Safety analysis report for packaging: neutron shipping cask, model 4T

    Peterson, R.T.

    1977-01-01

    This Safety Analysis Report for Packaging demonstrates that the neutron shipping cask can safely transport, in solid or powder form, all isotopes of uranium, plutonium, americium, curium, berkelium, californium, einsteinium, and fermium. The cask and its contents are described. It also evaluates transport conditions, structural parameters (e.g., load resistance, pressure and impact effects, lifting and tiedown devices), and shielding. Finally, it discusses compliance with Chapter 0529 of the Energy Research and Development Administration Manual, Safety Standards for the Packaging of Fissile and Other Radioactive Materials

  6. Models and Methods for the Design and Support of Liner Shipping Networks

    Koza, David Franz

    that may substantially change the way liner vessels are operated in the future. The article addresses the establishment of a large-scale liquefied natural gas supply chain along a major trade lane. It analyzes the interaction between long-term investment and operational costs, derives basic decision rules...... route be designed to achieve a well-connected but cost-efficient network? How shall port calls be scheduled and synchronized between shipping routes to offer the most economical and fastest transportation between ports? On which route shall containers be transported, if multiple options exist...

  7. Approximate Method of Calculating Forces on Rudder During Ship Sailing on a Shipping Route

    K. Zelazny

    2014-09-01

    Full Text Available Service speed of a ship in real weather conditions is a basic design parameter. Forecasting of this speed at preliminary design stage is made difficult by the lack of simple but at the same accurate models of forces acting upon a ship sailing on a preset shipping route. The article presents a model for calculating forces and moment on plane rudder, useful for forecasting of ship service speed at preliminary stages of ship design.

  8. PHOTOGRAMMETRIC MODEL BASED METHOD OF AUTOMATIC ORIENTATION OF SPACE CARGO SHIP RELATIVE TO THE INTERNATIONAL SPACE STATION

    Y. B. Blokhinov

    2012-07-01

    Full Text Available The technical problem of creating the new Russian version of an automatic Space Cargo Ship (SCS for the International Space Station (ISS is inseparably connected to the development of a digital video system for automatically measuring the SCS position relative to ISS in the process of spacecraft docking. This paper presents a method for estimating the orientation elements based on the use of a highly detailed digital model of the ISS. The input data are digital frames from a calibrated video system and the initial values of orientation elements, these can be estimated from navigation devices or by fast-and-rough viewpoint-dependent algorithm. Then orientation elements should be defined precisely by means of algorithmic processing. The main idea is to solve the exterior orientation problem mainly on the basis of contour information of the frame image of ISS instead of ground control points. A detailed digital model is used for generating raster templates of ISS nodes; the templates are used to detect and locate the nodes on the target image with the required accuracy. The process is performed for every frame, the resulting parameters are considered to be the orientation elements. The Kalman filter is used for statistical support of the estimation process and real time pose tracking. Finally, the modeling results presented show that the proposed method can be regarded as one means to ensure the algorithmic support of automatic space ships docking.

  9. Identification of Dynamically Positioned Ships

    Thor I. Fossen

    1996-04-01

    Full Text Available Todays model-based dynamic positioning (DP systems require that the ship and thruster dynamics are known with some accuracy in order to use linear quadratic optical control theory. However, it is difficult to identify the mathematical model of a dynamically posititmed (DP ship since the ship is not persistently excited under DP. In addition the ship parameter estimation problem is nonlinear and multivariable with only position and thruster state measurements available for parameter estimation. The process and measurement noise must also be modeled in order to avoid parameter drift due to environmental disturbances and sensor failure. This article discusses an off-line parallel extended Kalman filter (EKF algorithm utilizing two measurement series in parallel to estimate the parameters in the DP ship model. Full-scale experiments with a supply vessel are used to demonstrate the convergence and robustness of the proposed parameter estimator.

  10. Ship's barbers

    Unknown

    2003-01-01

    Showing two sailors having their hair cut (? one is possibly being shaved) on board ship. Three other sailors can be seen standing on the right-hand side of the photograph. The photograph is from an album inscribed 'H.M.S. Lancaster; Mediterranean Photographic Album: Diary of Events and Important Places Visited during the Commission 1910-1912' on the cover. This album was the property of Sydney Harold Liddle.

  11. Early Detection of Parametric Roll Resonance on Container Ships

    Galeazzi, Roberto; Blanke, Mogens; Poulsen, Niels Kjølstad

    2013-01-01

    Parametric roll resonance on ships is a nonlinear phenomenon where waves encountered at twice the natural roll frequency can bring the vessel dynamics into a bifurcation mode and lead to extreme values of roll. Recent years have seen several incidents with dramatic damage to container vessels...... the ship's speed and course, to escape from the bifurcation condition. This paper proposes nonparametric methods to detect the onset of roll resonance and demonstrates their performance. Theoretical conditions for parametric resonance are revisited and are used to develop efficient methods to detect its...... on experimental data from model tests and on data from a container ship crossing the Atlantic during a storm....

  12. Effect of passing vessels on a moored ship

    Lean, G H; Price, W A

    1977-11-01

    The effect of passing vessels on a moored ship was investigated by a series of model tests carried out at the Hydraulics Research Station for the Esso Petroleum Co. Ltd., transportation department in connection with their oil jetty at Milford Haven. A main conclusion was that the forces appeared to be due to the pressure gradients associated with the pattern of flow that accompanies the passing ship rather than with the wave system. Slack lines are to be avoided, and some relief in maximum line loads can be achieved by increasing the pretension. The results included the effects of passing vessel speed and ship clearance and draft.

  13. Analysis of a ship-to-ship collision

    Porter, V.L.; Ammerman, D.J.

    1996-01-01

    Sandia National Laboratories is involved in a safety assessment for the shipment of radioactive material by sea. One part of this study is investigation of the consequences of ship-to-ship collisions. This paper describes two sets of finite element analyses performed to assess the structural response of a small freighter and the loading imparted to radioactive material (RAM) packages during several postulated collision scenarios with another ship. The first series of analyses was performed to evaluate the amount of penetration of the freighter hull by a striking ship of various masses and initial velocities. Although these analyses included a representation of a single RAM package, the package was not impacted during the collision so forces on the package could not be computed. Therefore, a second series of analyses incorporating a representation of a row of seven packages was performed to ensure direct package impact by the striking ship. Average forces on a package were evaluated for several initial velocities and masses of the striking ship. In addition to. providing insight to ship and package response during a few postulated ship collisions scenarios, these analyses will be used to benchmark simpler ship collision models used in probabilistic risk assessment analyses

  14. Emissions of volatile organic compounds during the ship-loading of petroleum products: Dispersion modelling and environmental concerns.

    Milazzo, Maria Francesca; Ancione, Giuseppa; Lisi, Roberto

    2017-12-15

    Emissions due to ship-loading of hydrocarbons are currently not addressed neither by the Directive on the integrated pollution prevention or by other environmental regulations. The scope of this study is to point towards the environmental and safety concerns associated with such emissions, even if proper attention has not been given to this issue until now. In order to achieve this goal, the modelling of the emission volatile organic compounds (VOC), due to ship-load operations at refineries has been made by means of the definition of a simulation procedure which includes a proper treatment of the hours of calm. Afterwards, a quantitative analysis of VOC dispersion for an Italian case-study is presented with the primary aims: (i) to develop and verify the validity of the approach for the modelling of the emission sources and of the diffusion of these contaminants into the atmosphere by a proper treatment of the hours of calm and (ii) to identify their contribution to the total VOC emitted in a typical refinery. The calculated iso-concentration contours have also been drawn on a map and allowed the identification of critical areas for people protecting by the adoption of abatement solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Modelling the pile load test

    Prekop Ľubomír

    2017-01-01

    Full Text Available This paper deals with the modelling of the load test of horizontal resistance of reinforced concrete piles. The pile belongs to group of piles with reinforced concrete heads. The head is pressed with steel arches of a bridge on motorway D1 Jablonov - Studenec. Pile model was created in ANSYS with several models of foundation having properties found out from geotechnical survey. Finally some crucial results obtained from computer models are presented and compared with these obtained from experiment.

  16. Modelling the pile load test

    Prekop Ľubomír

    2017-01-01

    This paper deals with the modelling of the load test of horizontal resistance of reinforced concrete piles. The pile belongs to group of piles with reinforced concrete heads. The head is pressed with steel arches of a bridge on motorway D1 Jablonov - Studenec. Pile model was created in ANSYS with several models of foundation having properties found out from geotechnical survey. Finally some crucial results obtained from computer models are presented and compared with these obtained from exper...

  17. Experimental validation of new empirical models of the thermal properties of food products for safe shipping

    Hamid, Hanan H.; Mitchell, Mark; Jahangiri, Amirreza; Thiel, David V.

    2018-04-01

    Temperature controlled food transport is essential for human safety and to minimise food waste. The thermal properties of food are important for determining the heat transfer during the transient stages of transportation (door opening during loading and unloading processes). For example, the temperature of most dairy products must be confined to a very narrow range (3-7 °C). If a predefined critical temperature is exceeded, the food is defined as spoiled and unfit for human consumption. An improved empirical model for the thermal conductivity and specific heat capacity of a wide range of food products was derived based on the food composition (moisture, fat, protein, carbohydrate and ash). The models that developed using linear regression analysis were compared with the published measured parameters in addition to previously published theoretical and empirical models. It was found that the maximum variation in the predicated thermal properties leads to less than 0.3 °C temperature change. The correlation coefficient for these models was 0.96. The t-Stat test ( P-value >0.99) demonstrated that the model results are an improvement on previous works. The transient heat transfer based on the food composition and the temperature boundary conditions was found for a Camembert cheese (short cylindrical shape) using a multiple dimension finite difference method code. The result was verified using the heat transfer today (HTT) educational software which is based on finite volume method. The core temperature rises from the initial temperature (2.7 °C) to the maximum safe temperature in ambient air (20.24 °C) was predicted to within about 35.4 ± 0.5 min. The simulation results agree very well ( +0.2 °C) with the measured temperature data. This improved model impacts on temperature estimation during loading and unloading the trucks and provides a clear direction for temperature control in all refrigerated transport applications.

  18. Ship Roll Motion Control

    Perez, Tristan; Blanke, Mogens

    2010-01-01

    . This tutorial paper presents an account of the development of various ship roll motion control systems and the challenges associated with their design. The paper discusses how to assess performance, the applicability of dierent models, and control methods that have been applied in the past....

  19. Torpedo modelling in TORSIM and torpedo defence test bed

    Grootendorst, H.J.; Benders, F.P.A.; Driessen, F.P.G.; Witberg, R.

    2002-01-01

    The validated TORSIM (TORpedo SlMulation) model simulates the behaviour and determines the effectiveness of different torpedo types (MK46 and MK48), launched from a surface ship, from an air vehicle or from a submarine , against different types of submarine s or surface ships. Evasive manoeuvres of

  20. Production Balance of Ship Erection

    JIANG Ru-hong; TAN Jia-hua; LIU Cun-gen

    2008-01-01

    A network plan model of ship erection was established based on the network planning technologyand the work-package breakdown system. The load-oriented production control method was introduced to buildup a throughput diagram model thus it is possible to describe the ship erection process numerically. Based onthe digitaiized models some cases of production balance of ship erection were studied and three balance indexeswere put forward, they are the load balance rate, the input manpower balance rate and the maximum gantrycrane operating times. Such an analytic method based on the balance evaluation is the important foundationfor digitization and intelligentization of shipyard production management.

  1. Solving multi-product inventory ship routing with a heterogeneous fleet model using a hybrid cross entropy-genetic algorithm: a case study in Indonesia

    Budi Santosa

    2016-01-01

    Full Text Available This paper presents a model and an algorithm for an inventory ship routing problem (ISRP. It consists of two main parts: a model development of the ship routing problem in a multi-product inventory with a heterogeneous fleet and an algorithm development to solve the problem. The problem is referred to as ISRP. ISRP considers several parameters including the deadweight tonnage (DWT, product compatibility, port setup, and compartment washing costs. Considering these parameters, the objective function is to minimize the total cost, which consists of traveling, port setup, ship charter, and compartment washing costs. From the resulting model, there are two major steps used to solve the problem. The first is to select the ships in order to satisfy the constraint that restricts the mooring rule. The second is to find the best route, product allocation, and shipped quantity. ISRP is an Non Polynomial-hard problem. Finding the solution of such problem needs a high computation time. A new hybrid metaheuristics, namely the cross entropy-genetic algorithm (CEGA, was proposed to solve ISRP. The results were then compared with those resulted from a hybrid Tabu Search to measure the hybrid CEGA performance. The results showed that CEGA provided better solutions than those produced by the hybrid Tabu Search.

  2. Contribution of ship emissions to the concentration of PM2.5: A comprehensive study using AIS data and WRF/Chem model in Bohai Rim Region, China.

    Chen, Dongsheng; Zhao, Na; Lang, Jianlei; Zhou, Ying; Wang, Xiaotong; Li, Yue; Zhao, Yuehua; Guo, Xiurui

    2018-01-01

    Compared with on-road vehicles, emission from ships is one of the least-regulated anthropogenic emission sources and non-negligible source of primary aerosols and gas-phase precursors of PM 2.5 . The Bohai Rim Region in China hosts dozens of large ports, two of which ranked among the top ten ports in the world. To determine the impact of ship emissions on the PM 2.5 concentrations over this region, two parts of works have been conducted in this study. First, a detailed ship emission inventory with high spatiotemporal resolution was developed based on Automatic Identification System (AIS) data. Then the WRF/Chem model was applied to modeling the impact of ship emissions by comparing two scenarios: with and without ship emissions. The results indicate that the total estimated ship emissions of SO 2 , NO X , PM 10 , PM 2.5 , CO, HC, and CO 2 from Bohai Rim Region in 2014 are 1.9×10 5 , 2.9×10 5 , 2.6×10 4 , 2.4×10 4 , 2.5×10 4 , 1.2×10 4 , and 1.3×10 7 tonnes, respectively. The modeling results indicate that the annual PM 2.5 concentrations increased by 5.9% on land areas of Bohai Rim Region (the continent within 115.2°E-124.3°E and 36.1°N-41.6°N) due to ship emissions. The contributions show distinctive seasonal variations of contributions, presenting highest in summer (12.5%) followed by spring (6.9%) and autumn (3.3%), and lowest in winter (0.9%). The contribution reaches up to 10.7% along the shoreline and down to 1.0% 200km inland. After examining the statistics of the modeling results during heavy and non-heavy haze days in July, it was found that 6 out of 9 cities around the Bohai Rim Region were observed with higher contributions from ship emissions during heavy haze days compared with non-heavy haze days. These results indicate that the impacts of ship emissions on the ambient PM 2.5 are non-negligible, especially for heavy haze days for most coastal cities in the Bohai Rim Region. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Methods for testing transport models

    Singer, C.; Cox, D.

    1991-01-01

    Substantial progress has been made over the past year on six aspects of the work supported by this grant. As a result, we have in hand for the first time a fairly complete set of transport models and improved statistical methods for testing them against large databases. We also have initial results of such tests. These results indicate that careful application of presently available transport theories can reasonably well produce a remarkably wide variety of tokamak data

  4. Exergy Analysis of Complex Ship Energy Systems

    Pierre Marty

    2016-04-01

    Full Text Available With multiple primary and secondary energy converters (diesel engines, steam turbines, waste heat recovery (WHR and oil-fired boilers, etc. and extensive energy networks (steam, cooling water, exhaust gases, etc., ships may be considered as complex energy systems. Understanding and optimizing such systems requires advanced holistic energy modeling. This modeling can be done in two ways: The simpler approach focuses on energy flows, and has already been tested, approved and presented; a new, more complicated approach, focusing on energy quality, i.e., exergy, is presented in this paper. Exergy analysis has rarely been applied to ships, and, as a general rule, the shipping industry is not familiar with this tool. This paper tries to fill this gap. We start by giving a short reminder of what exergy is and describe the principles of exergy modeling to explain what kind of results should be expected from such an analysis. We then apply these principles to the analysis of a large two-stroke diesel engine with its cooling and exhaust systems. Simulation results are then presented along with the exergy analysis. Finally, we propose solutions for energy and exergy saving which could be applied to marine engines and ships in general.

  5. NET model coil test possibilities

    Erb, J.; Gruenhagen, A.; Herz, W.; Jentzsch, K.; Komarek, P.; Lotz, E.; Malang, S.; Maurer, W.; Noether, G.; Ulbricht, A.; Vogt, A.; Zahn, G.; Horvath, I.; Kwasnitza, K.; Marinucci, C.; Pasztor, G.; Sborchia, C.; Weymuth, P.; Peters, A.; Roeterdink, A.

    1987-11-01

    A single full size coil for NET/INTOR represents an investment of the order of 40 MUC (Million Unit Costs). Before such an amount of money or even more for the 16 TF coils is invested as much risks as possible must be eliminated by a comprehensive development programme. In the course of such a programme a coil technology verification test should finally prove the feasibility of NET/INTOR TF coils. This study report is almost exclusively dealing with such a verification test by model coil testing. These coils will be built out of two Nb 3 Sn-conductors based on two concepts already under development and investigation. Two possible coil arrangements are discussed: A cluster facility, where two model coils out of the two Nb 3 TF-conductors are used, and the already tested LCT-coils producing a background field. A solenoid arrangement, where in addition to the two TF model coils another model coil out of a PF-conductor for the central PF-coils of NET/INTOR is used instead of LCT background coils. Technical advantages and disadvantages are worked out in order to compare and judge both facilities. Costs estimates and the time schedules broaden the base for a decision about the realisation of such a facility. (orig.) [de

  6. Life-Cycle Cost and Risk Analysis of Alternative Configurations for Shipping Low-Level Radioactive Waste to the Nevada Test Site

    PM Daling; SB Ross; BM Biwer

    1999-01-01

    The Nevada Test Site (NTS) is a major receiver of low-level radioactive waste (LLW) for disposal. Currently, all LLW received at NTS is shipped by truck. The trucks use highway routes to NTS that pass through the Las Vegas Valley and over Hoover Dam, which is a concern of local stakeholder groups in the State of Nevada. Rail service offers the opportunity to reduce transportation risks and costs, according to the Waste Management Programmatic Environmental Impact Statement (WM-PEIS). However, NTS and some DOE LLW generator sites are not served with direct rail service so intermodal transport is under consideration. Intermodal transport involves transport via two modes, in this case truck and rail, from the generator sites to NTS. LLW shipping containers would be transferred between trucks and railcars at intermodal transfer points near the LLW generator sites, NTS, or both. An Environmental Assessment (EA)for Intermodal Transportation of Low-Level Radioactive Waste to the Nevada Test Site (referred to as the NTSIntermodal -M) has been prepared to determine whether there are environmental impacts to alterations to the current truck routing or use of intermodal facilities within the State of Nevada. However, an analysis of the potential impacts outside the State of Nevada are not addressed in the NTS Intermodal EA. This study examines the rest of the transportation network between LLW generator sites and the NTS and evaluates the costs, risks, and feasibility of integrating intermodal shipments into the LLW transportation system. This study evaluates alternative transportation system configurations for NTS approved and potential generators based on complex-wide LLW load information. Technical judgments relative to the availability of DOE LLW generators to ship from their sites by rail were developed. Public and worker risk and life-cycle cost components are quantified. The study identifies and evaluates alternative scenarios that increase the use of rail (intermodal

  7. Life-Cycle Cost and Risk Analysis of Alternative Configurations for Shipping Low-Level Radioactive Waste to the Nevada Test Site

    PM Daling; SB Ross; BM Biwer

    1999-12-17

    The Nevada Test Site (NTS) is a major receiver of low-level radioactive waste (LLW) for disposal. Currently, all LLW received at NTS is shipped by truck. The trucks use highway routes to NTS that pass through the Las Vegas Valley and over Hoover Dam, which is a concern of local stakeholder groups in the State of Nevada. Rail service offers the opportunity to reduce transportation risks and costs, according to the Waste Management Programmatic Environmental Impact Statement (WM-PEIS). However, NTS and some DOE LLW generator sites are not served with direct rail service so intermodal transport is under consideration. Intermodal transport involves transport via two modes, in this case truck and rail, from the generator sites to NTS. LLW shipping containers would be transferred between trucks and railcars at intermodal transfer points near the LLW generator sites, NTS, or both. An Environmental Assessment (EA)for Intermodal Transportation of Low-Level Radioactive Waste to the Nevada Test Site (referred to as the NTSIntermodal -M) has been prepared to determine whether there are environmental impacts to alterations to the current truck routing or use of intermodal facilities within the State of Nevada. However, an analysis of the potential impacts outside the State of Nevada are not addressed in the NTS Intermodal EA. This study examines the rest of the transportation network between LLW generator sites and the NTS and evaluates the costs, risks, and feasibility of integrating intermodal shipments into the LLW transportation system. This study evaluates alternative transportation system configurations for NTS approved and potential generators based on complex-wide LLW load information. Technical judgments relative to the availability of DOE LLW generators to ship from their sites by rail were developed. Public and worker risk and life-cycle cost components are quantified. The study identifies and evaluates alternative scenarios that increase the use of rail (intermodal

  8. Survival of viral pathogens in animal feed ingredients under transboundary shipping models

    Bauermann, Fernando V.; Niederwerder, Megan C.; Singrey, Aaron; Clement, Travis; de Lima, Marcelo; Long, Craig; Patterson, Gilbert; Sheahan, Maureen A.; Stoian, Ana M. M.; Petrovan, Vlad; Jones, Cassandra K.; De Jong, Jon; Ji, Ju; Spronk, Gordon D.; Minion, Luke; Christopher-Hennings, Jane; Zimmerman, Jeff J.; Rowland, Raymond R. R.; Nelson, Eric; Sundberg, Paul; Diel, Diego G.

    2018-01-01

    The goal of this study was to evaluate survival of important viral pathogens of livestock in animal feed ingredients imported daily into the United States under simulated transboundary conditions. Eleven viruses were selected based on global significance and impact to the livestock industry, including Foot and Mouth Disease Virus (FMDV), Classical Swine Fever Virus (CSFV), African Swine Fever Virus (ASFV), Influenza A Virus of Swine (IAV-S), Pseudorabies virus (PRV), Nipah Virus (NiV), Porcine Reproductive and Respiratory Syndrome Virus (PRRSV), Swine Vesicular Disease Virus (SVDV), Vesicular Stomatitis Virus (VSV), Porcine Circovirus Type 2 (PCV2) and Vesicular Exanthema of Swine Virus (VESV). Surrogate viruses with similar genetic and physical properties were used for 6 viruses. Surrogates belonged to the same virus families as target pathogens, and included Senecavirus A (SVA) for FMDV, Bovine Viral Diarrhea Virus (BVDV) for CSFV, Bovine Herpesvirus Type 1 (BHV-1) for PRV, Canine Distemper Virus (CDV) for NiV, Porcine Sapelovirus (PSV) for SVDV and Feline Calicivirus (FCV) for VESV. For the remaining target viruses, actual pathogens were used. Virus survival was evaluated using Trans-Pacific or Trans-Atlantic transboundary models involving representative feed ingredients, transport times and environmental conditions, with samples tested by PCR, VI and/or swine bioassay. SVA (representing FMDV), FCV (representing VESV), BHV-1 (representing PRV), PRRSV, PSV (representing SVDV), ASFV and PCV2 maintained infectivity during transport, while BVDV (representing CSFV), VSV, CDV (representing NiV) and IAV-S did not. Notably, more viruses survived in conventional soybean meal, lysine hydrochloride, choline chloride, vitamin D and pork sausage casings. These results support published data on transboundary risk of PEDV in feed, demonstrate survival of certain viruses in specific feed ingredients (“high-risk combinations”) under conditions simulating transport between

  9. Collaborative testing of turbulence models

    Bradshaw, P.

    1992-12-01

    This project, funded by AFOSR, ARO, NASA, and ONR, was run by the writer with Profs. Brian E. Launder, University of Manchester, England, and John L. Lumley, Cornell University. Statistical data on turbulent flows, from lab. experiments and simulations, were circulated to modelers throughout the world. This is the first large-scale project of its kind to use simulation data. The modelers returned their predictions to Stanford, for distribution to all modelers and to additional participants ('experimenters')--over 100 in all. The object was to obtain a consensus on the capabilities of present-day turbulence models and identify which types most deserve future support. This was not completely achieved, mainly because not enough modelers could produce results for enough test cases within the duration of the project. However, a clear picture of the capabilities of various modeling groups has appeared, and the interaction has been helpful to the modelers. The results support the view that Reynolds-stress transport models are the most accurate.

  10. Development of nuclear powered ship in Japan

    Sato, Hiroshi

    1976-01-01

    The development of nuclear merchant ship in Japan was started in 1955 by the establishment of Nuclear Ship Study Group, and since then, the investigation, test and research on nuclear ships have been continued. As a result, a nuclear ocean observation and supply ship was designed for trial. Researches were carried out also in JAERI and Institute for Technical Research of Ships. Meanwhile, the nuclear icebreaker Lenin was completed in Soviet Union in 1959, the nuclear ship Savannah set out for maiden voyage in U.S. in 1962, and the construction of the nuclear ore carrier Otto Hahn was prepared in FRG. Japan Nuclear Ship Development Corp. was established in 1963, and started the design and construction of the first nuclear ship in Japan, Mutsu. The basic policy in the construction is the improvement of nuclear ship technology, the securing of safety, and the use of domestic technologies as far as possible. The progress of the design, construction and test of the Mutsu is described. Owing to the problem of radiation leak, the development of nuclear ships stagnated for a while, but the nuclear plant of the Mutsu demonstrated the expected performance in the functional test, land criticality test and zero output test, and it is expected that the bud of the independent development brought up so far can bear valuable fruit. The independent development of marine nuclear reactors should be continued by selecting the way most suitable to Japan. (Kako, I.)

  11. Model calculations of the effects of present and future emissions of air pollutants from shipping in the Baltic Sea and the North Sea

    J. E. Jonson

    2015-01-01

    Full Text Available Land-based emissions of air pollutants in Europe have steadily decreased over the past two decades, and this decrease is expected to continue. Within the same time span emissions from shipping have increased in EU ports and in the Baltic Sea and the North Sea, defined as SECAs (sulfur emission control areas, although recently sulfur emissions, and subsequently particle emissions, have decreased. The maximum allowed sulfur content in marine fuels in EU ports is now 0.1%, as required by the European Union sulfur directive. In the SECAs the maximum fuel content of sulfur is currently 1% (the global average is about 2.4%. This will be reduced to 0.1% from 2015, following the new International Maritime Organization (IMO rules. In order to assess the effects of ship emissions in and around the Baltic Sea and the North Sea, regional model calculations with the EMEP air pollution model have been made on a 1/4° longitude × 1/8° latitude resolution, using ship emissions in the Baltic Sea and the North Sea that are based on accurate ship positioning data. The effects on depositions and air pollution and the resulting number of years of life lost (YOLLs have been calculated by comparing model calculations with and without ship emissions in the two sea areas. In 2010 stricter regulations for sulfur emissions were implemented in the two sea areas, reducing the maximum sulfur content allowed in marine fuels from 1.5 to 1%. In addition ships were required to use fuels with 0.1 % sulfur in EU harbours. The calculations have been made with emissions representative of 2009 and 2011, i.e. before and after the implementation of the stricter controls on sulfur emissions from 2010. The calculations with present emissions show that per person, an additional 0.1–0.2 years of life lost is estimated in areas close to the major ship tracks with current emission levels. Comparisons of model calculations with emissions before and after the implementation of stricter

  12. Methods for testing transport models

    Singer, C.; Cox, D.

    1993-01-01

    This report documents progress to date under a three-year contract for developing ''Methods for Testing Transport Models.'' The work described includes (1) choice of best methods for producing ''code emulators'' for analysis of very large global energy confinement databases, (2) recent applications of stratified regressions for treating individual measurement errors as well as calibration/modeling errors randomly distributed across various tokamaks, (3) Bayesian methods for utilizing prior information due to previous empirical and/or theoretical analyses, (4) extension of code emulator methodology to profile data, (5) application of nonlinear least squares estimators to simulation of profile data, (6) development of more sophisticated statistical methods for handling profile data, (7) acquisition of a much larger experimental database, and (8) extensive exploratory simulation work on a large variety of discharges using recently improved models for transport theories and boundary conditions. From all of this work, it has been possible to define a complete methodology for testing new sets of reference transport models against much larger multi-institutional databases

  13. Program to develop analytical tools for environmental and safety assessment of nuclear material shipping container systems

    Butler, T.A.

    1978-11-01

    This paper describes a program for developing analytical techniques to evaluate the response of nuclear material shipping containers to severe accidents. Both lumped-mass and finite element techniques are employed to predict shipping container and shipping container-carrier response to impact. The general impact problem is computationally expensive because of its nonlinear, three-dimensional nature. This expense is minimized by using approximate models to parametrically identify critical cases before more exact analyses are performed. The computer codes developed for solving the problem are being experimentally substantiated with test data from full-scale and scale-model container drop tests. 6 figures, 1 table

  14. Towards seasonal Arctic shipping route predictions

    Haines, K.; Melia, N.; Hawkins, E.; Day, J. J.

    2017-12-01

    In our previous work [1] we showed how trans-Arctic shipping routes would become more available through the 21st century as sea ice declines, using CMIP5 models with means and stds calibrated to PIOMAS sea ice observations. Sea ice will continue to close shipping routes to open water vessels through the winter months for the foreseeable future so the availability of open sea routes will vary greatly from year to year. Here [2] we look at whether the trans-Arctic shipping season period can be predicted in seasonal forecasts, again using several climate models, and testing both perfect and imperfect knowledge of the initial sea ice conditions. We find skilful predictions of the upcoming summer shipping season can be made from as early as January, although typically forecasts may show lower skill before a May `predictability barrier'. Focussing on the northern sea route (NSR) off Siberia, the date of opening of this sea route is twice as variable as the closing date, and this carries through to reduced predictability at the start of the season. Under climate change the later freeze-up date accounts for 60% of the lengthening season, Fig1 We find that predictive skill is state dependent with predictions for high or low ice years exhibiting greater skill than for average ice years. Forecasting the exact timing of route open periods is harder (more weather dependent) under average ice conditions while in high and low ice years the season is more controlled by the initial ice conditions from spring onwards. This could be very useful information for companies planning vessel routing for the coming season. We tested this dependence on the initial ice conditions by changing the initial ice state towards climatologically average conditions and show directly that early summer sea-ice thickness information is crucial to obtain skilful forecasts of the coming shipping season. Mechanisms for this are discussed. This strongly suggests that good sea ice thickness observations

  15. A thermodynamic and heat transfer model for LNG ageing during ship transportation. Towards an efficient boil-off gas management

    Krikkis, Rizos N.

    2018-06-01

    A non-equilibrium thermodynamic and heat transfer model for LNG ageing during ship transportation has been developed based on experimental data. The measurements reveal that the liquid temperature remains nearly constant, whereas significant variations are observed for the gas temperature. The measurement of the liquid temperature along the tank height suggests that a small scale rollover phenomenon may have taken place in one cargo tank. A time dependent heat transfer mechanism has been considered by taking into account the temperature variations of the atmospheric air, the seawater and the cofferdam environment which affect the cargo tanks. An important finding is that the evaporation rate (boil-of rate) is forced to follow the fuel flow consumption profile imposed by the vessel's propulsion system in order to match the tank pressure and volume constraints. The theoretical model is favorably compared to a comprehensive set on per hour basis of on board measurements of cargo temperatures and pressures, recorded during laden voyages, providing a better understanding of the underlying processes involved. The dominant role of the fuel consumption on the evaporation rate may be utilized in order to devise an efficient cargo management strategy during the laden voyage.

  16. SURVEYING, MODELING AND 3D REPRESENTATION OF A WRECK FOR DIVING PURPOSES: CARGO SHIP “VERA”

    A. Ktistis

    2017-02-01

    Full Text Available This paper presents the results from an underwater recording of the stern part of a contemporary cargo-ship wreck. The aim of this survey was to create 3D representations of this wreck mainly for recreational diving purposes. The key points of this paper are: a the implementation of the underwater recording at a diving site; b the reconstruction of a 3d model from data that have been captured by recreational divers; and c the development of a set of products to be used by the general public for the ex situ presentation or for the in situ navigation. The idea behind this project is to define a simple and low cost procedure for the surveying, modeling and 3D representation of a diving site. The perspective of our team is to repeat the proposed methodology for the documentation and the promotion of other diving sites with cultural features, as well as to train recreational divers in underwater surveying procedures towards public awareness and community engagement in the maritime heritage.

  17. Noise Localization Method for Model Tests in a Large Cavitation Tunnel Using a Hydrophone Array

    Cheolsoo Park

    2016-02-01

    Full Text Available Model tests are performed in order to predict the noise level of a full ship and to control its noise signature. Localizing noise sources in the model test is therefore an important research subject along with measuring noise levels. In this paper, a noise localization method using a hydrophone array in a large cavitation tunnel is presented. The 45-channel hydrophone array was designed using a global optimization technique for noise measurement. A set of noise experiments was performed in the KRISO (Korea Research Institute of Ships & Ocean Engineering large cavitation tunnel using scaled models, including a ship with a single propeller, a ship with twin propellers and an underwater vehicle. The incoherent broadband processors defined based on the Bartlett and the minimum variance (MV processors were applied to the measured data. The results of data analysis and localization are presented in the paper. Finally, it is shown that the mechanical noise, as well as the propeller noise can be successfully localized using the proposed localization method.

  18. Risk of Cyberterrorism to Naval Ships Inport Naval Station Everett: A Model Based Project Utilizing SIAM

    Tester, Rodrick A

    2007-01-01

    .... In doing so, an influence net model was designed to discover the likelihood of a successful cyber attack However, first it was necessary to establish what the best mitigation tools are in defense...

  19. Who steers the ship? Rural family physicians' views on collaborative care models for patients with dementia.

    Kosteniuk, Julie; Morgan, Debra; Innes, Anthea; Keady, John; Stewart, Norma; D'Arcy, Carl; Kirk, Andrew

    2014-01-01

    Little is known about the views of rural family physicians (FPs) regarding collaborative care models for patients with dementia. The study aims were to explore FPs' views regarding this issue, their role in providing dementia care, and the implications of providing dementia care in a rural setting. This study employed an exploratory qualitative design with a sample of 15 FPs. All rural FPs indicated acceptance of collaborative models. The main disadvantages of practicing rural were accessing urban-based health care and related services and a shortage of local health care resources. The primary benefit of practicing rural was FPs' social proximity to patients, families, and some health care workers. Rural FPs provided care for patients with dementia that took into account the emotional and practical needs of caregivers and families. FPs described positive and negative implications of rural dementia care, and all were receptive to models of care that included other health care professionals.

  20. Green shipping management

    Lun, Y H Venus; Wong, Christina W Y; Cheng, T C E

    2016-01-01

    This book presents theory-driven discussion on the link between implementing green shipping practices (GSP) and shipping firm performance. It examines the shipping industry’s challenge of supporting economic growth while enhancing environmental performance. Consisting of nine chapters, the book covers topics such as the conceptualization of green shipping practices (GSPs), measurement scales for evaluating GSP implementation, greening capability, greening and performance relativity (GPR), green management practice, green shipping network, greening capacity, and greening propensity. In view of the increasing quest for environment protection in the shipping sector, this book provides a good reference for firms to understand and evaluate their capability in carrying out green operations on their shipping activities.

  1. Design and experiments with scale model of a ship with dynamic positioning system

    Souza, Carlos Eduardo S.; Morishita, Helio M.; Moratelli Junior, Lazaro; Lago, Glenan A.; Tannuri, Eduardo A. [Universidade de Sao Paulo (USP), SP (Brazil)

    2008-07-01

    Dynamic Positioning Systems (DPS) are used to keep a floating vessel on a specific position or follow pre-defined path through the action of controlled propellers. This paper describes a facility used to experimentally analyze DPS and to validate a numerical simulator. It is composed by a scale model of a DP tanker with 3 thrusters, a measurement system based on computational vision and a control software with the same DP algorithms used in industrial systems. Simple wind and current generators were also implemented. This work shows preliminary results of experiments, which has been useful to calibrate the simulator and to validate the mathematical model. (author)

  2. Viking FellowSHIP: Norwegian hydrogen ship on the right course

    Larssen-Aas, Kari

    2006-01-01

    In the future fuel cells will change the world of shipping's economical conditions, and environmental effects from this industry. A new model of a hydrogen fuelled ship was presented at the ONS exhibition in Stavanger 2006. The technology may revolutionize the shipping industry. A brief description of the project is presented (ml)

  3. Extraction of the mode shapes of a segmented ship model with a hydroelastic response

    Yooil Kim

    2015-11-01

    Full Text Available The mode shapes of a segmented hull model towed in a model basin were predicted using both the Proper Orthogonal Decomposition (POD and cross random decrement technique. The proper orthogonal decomposition, which is also known as Karhunen-Loeve decomposition, is an emerging technology as a useful signal processing technique in structural dynamics. The technique is based on the fact that the eigenvectors of a spatial coherence matrix become the mode shapes of the system under free and randomly excited forced vibration conditions. Taking advantage of the sim-plicity of POD, efforts have been made to reveal the mode shapes of vibrating flexible hull under random wave ex-citation. First, the segmented hull model of a 400 K ore carrier with 3 flexible connections was towed in a model basin under different sea states and the time histories of the vertical bending moment at three different locations were meas-ured. The measured response time histories were processed using the proper orthogonal decomposition, eventually to obtain both the first and second vertical vibration modes of the flexible hull. A comparison of the obtained mode shapes with those obtained using the cross random decrement technique showed excellent correspondence between the two results.

  4. Measures of Model Uncertainty in the Assessment of Primary Stresses in Ship Structures

    Östergaard, Carsten; Dogliani, Mario; Guedes Soares, Carlos

    1996-01-01

    The paper considers various models and methods commonly used for linear elastic stress analysis and assesses the uncertainty involved in their application to the analysis of the distribution of primary stresses in the hull of a containership example, through statistical evaluations of the results...

  5. Modeling Stochastic Boundary Conditions in a Coastal Catchment using a Bayesian Network: An Application to the Houston Ship Channel, Texas

    Couasnon, Anaïs; Sebastian, Antonia; Morales-Nápoles, Oswaldo

    2017-04-01

    Recent research has highlighted the increased risk of compound flooding in the U.S. In coastal catchments, an elevated downstream water level, resulting from high tide and/or storm surge, impedes drainage creating a backwater effect that may exacerbate flooding in the riverine environment. Catchments exposed to tropical cyclone activity along the Gulf of Mexico and Atlantic coasts are particularly vulnerable. However, conventional flood hazard models focus mainly on precipitation-induced flooding and few studies accurately represent the hazard associated with the interaction between discharge and elevated downstream water levels. This study presents a method to derive stochastic boundary conditions for a coastal watershed. Mean daily discharge and maximum daily residual water levels are used to build a non-parametric Bayesian network (BN) based on copulas. Stochastic boundary conditions for the watershed are extracted from the BN and input into a 1-D process-based hydraulic model to obtain water surface elevations in the main channel of the catchment. The method is applied to a section of the Houston Ship Channel (Buffalo Bayou) in Southeast Texas. Data at six stream gages and two tidal stations are used to build the BN and 100-year joint return period events are modeled. We find that the dependence relationship between the daily residual water level and the mean daily discharge in the catchment can be represented by a Gumbel copula (Spearman's rank correlation coefficient of 0.31) and that they result in higher water levels in the mid- to upstream reaches of the watershed than when modeled independently. This indicates that conventional (deterministic) methods may underestimate the flood hazard associated with compound flooding in the riverine environment and that such interactions should not be neglected in future coastal flood hazard studies.

  6. Test model of WWER core

    Tikhomirov, A. V.; Gorokhov, A. K.

    2007-01-01

    The objective of this paper is creation of precision test model for WWER RP neutron-physics calculations. The model is considered as a tool for verification of deterministic computer codes that enables to reduce conservatism of design calculations and enhance WWER RP competitiveness. Precision calculations were performed using code MCNP5/1/ (Monte Carlo method). Engineering computer package Sapfir 9 5andRC V VER/2/ is used in comparative analysis of the results, it was certified for design calculations of WWER RU neutron-physics characteristic. The object of simulation is the first fuel loading of Volgodon NPP RP. Peculiarities of transition in calculation using MCNP5 from 2D geometry to 3D geometry are shown on the full-scale model. All core components as well as radial and face reflectors, automatic regulation in control and protection system control rod are represented in detail description according to the design. The first stage of application of the model is assessment of accuracy of calculation of the core power. At the second stage control and protection system control rod worth was assessed. Full scale RP representation in calculation using code MCNP5 is time consuming that calls for parallelization of computational problem on multiprocessing computer (Authors)

  7. Wind Tunnel Assessment of Ship Manoeuvrability using a PMM Technique

    Agdrup, Kristian; Jensen, Andreas G.; Aage, Christian

    1999-01-01

    Tests have been performed at the Danish Maritime Institute (DMI) to investigate the applicability of a new wind tunnel Planar Motion Mechanism (PMM) for the determination of hydrodynamic coefficients of ships. The method has been tested on a tanker with known towing tank data. The wind tunnel model...... data giving reasonable results. The dependency of amplitude and frequency is evaluated, and sources of inaccuracy are discussed. It is concluded that the wind tunnel method is a promising method to achieve a fast and cost-effective estimate of the hydrodynamic coefficients of a ship hull...

  8. Solar UV radiation exposure of seamen - Measurements, calibration and model calculations of erythemal irradiance along ship routes

    Feister, Uwe [German Meteorological Service, Meteorological Observatory Lindenberg - Richard-Assmann-Observatory, Am Observatorium 12, 15848 Lindenberg (Germany); Meyer, Gabriele; Kirst, Ulrich [German Social Accident Insurance Institution for Transport and Traffic, Ottenser Hauptstrasse 54, 22765 Hamburg (Germany)

    2013-05-10

    Seamen working on vessels that go along tropical and subtropical routes are at risk to receive high doses of solar erythemal radiation. Due to small solar zenith angles and low ozone values, UV index and erythemal dose are much higher than at mid-and high latitudes. UV index values at tropical and subtropical Oceans can exceed UVI = 20, which is more than double of typical mid-latitude UV index values. Daily erythemal dose can exceed the 30-fold of typical midlatitude winter values. Measurements of erythemal exposure of different body parts on seamen have been performed along 4 routes of merchant vessels. The data base has been extended by two years of continuous solar irradiance measurements taken on the mast top of RV METEOR. Radiative transfer model calculations for clear sky along the ship routes have been performed that use satellite-based input for ozone and aerosols to provide maximum erythemal irradiance and dose. The whole data base is intended to be used to derive individual erythemal exposure of seamen during work-time.

  9. Impact analysis of spent nuclear fuel shipping casks

    Huerta, M.; Dennis, A.W.; Yoshimura, R.H.

    1978-07-01

    A presentation made at the CUBE (Computer Use By Engineers) Symposium, October 1976, in Albuquerque, New Mexico is summarized. A full-scale testing program involving impact tests of spent-nuclear-fuel shipping systems is described. This program is being conducted by Sandia Laboratories for the Environmental Control Technology Division of the U.S. Energy Research and Development Administration. The analytical and scale modeling techniques being employed to predict the response of the full-scale system in the very severe impact tests are described. The analytical techniques include lumped parameter modeling of the vehicle and cask system and finite modeling of isolated shipping casks. Some preliminary results from the mathematical analyses and scale model tests demonstrate close agreement between these two techniques. Scale models of the systems are also described and some results presented

  10. Pressure suppression system (PSS) for nuclear ships. Experimental results obtained at the GKSS PSS-test-facillity

    Aust, E.; Niemann, H.R.; Schwan, H.; Vollbrandt, J.

    1978-01-01

    The PSS-test facility is shortly presented which was designed to show experimentally the operation of the pressure suppression containment for the NCS 80 concept. The results of the experimental LOCA-simulation tests in the PSS-test facility are illustrated by diagrams. The observed phenomena as chugging and pessure oscillations immediately after vent clearing are reported as well as the thermohydraulic loadings of the total system. Finally a short view is given on the future test program

  11. The shipping man adventures in ship finance

    McCleery, Matthew

    2013-01-01

    When restless New York City hedge fund manager Robert Fairchild watches the Baltic Dry Cargo Index plunge 97%, registering an all-time high and a 25-year low within the span of just six months, he decides to buy a ship. Immediately fantasizing about naming a vessel after his wife, carrying a string of worry beads and being able to introduce himself as a "shipowner" at his upcoming college reunion, Fairchild immediately embarks on an odyssey into the most exclusive, glamorous and high stakes business in the world. From pirates off the coast of Somalia and on Wall Street to Greek and Norwegian shipping magnates, the education of Robert Fairchild is an expensive one. In the end, he loses his hedge fund, but he gains a life - as a Shipping Man. Part fast paced financial thriller, part ship finance text book, The Shipping Man is 310 pages of required reading for anyone with an interest in capital formation for shipping.

  12. Modeling of Complex Structures for the Ship's Power Complex Using Xilinx System

    Chernyi Sergei

    2015-02-01

    Full Text Available One of the most essential tasks for a number of systems of the automatic controls in the autonomous electric power systems of the water transport is accurate calculation of variable harmonic components in the non-sinusoidal signal. In the autonomous electric power systems operating with full semiconductor capacity, the forms of line currents and voltages are greatly distorted, and generator devices generate voltage with inconsistent frequency, phase and amplitude. It makes calculation of harmonic composition of the distorted signals be a non-trivial task. The present paper provides a mathematical set for solution of the outlined problem including the realization in the discrete form. The simplicity and efficiency of the system proposed make possible to perform its practical realization with the help of cheap FPGA. The test of the developed system has been performed in the medium Matlab.

  13. Analysis of International Commodity Shipping Data and the Shipment of NORM to the United States

    Baciak, James E.; Ely, James H.; Schweppe, John E.; Sandness, Gerald A.; Robinson, Sean M.

    2011-10-01

    As part of the Spreader Bar Radiation Detector project, PNNL analyzed US import data shipped through US ports collected over the 12 months of 2006 (over 4.5 million containers). Using these data, we extracted a variety of distributions that are of interest to modelers and developers of active and passive detection systems used to 'scan' IMCCs for potential contraband. This report expands on some of the analysis presented in an earlier report from LLNL, by investigation the foreign port distribution of commodities shipped to the US. The majority of containers shipped to the United States are 40 ft containers ({approx}70%); about 25% are 20 ft; and about 3.6% are 45 ft containers. A small fraction (<1%) of containers are of other more specialized sizes, and very few ports actually ship these unique size containers (a full distribution for all foreign ports is shown in Appendix A below). The primary foreign ports that ship the largest fraction of each container are shown in the table below. Given that 45 ft containers comprise 1 of out every 27 containers shipped to the US, and given the foreign ports from which they are shipped, they should not be ignored in screening; further testing and analysis of radiation measurements for national security with this size container is warranted. While a large amount of NORM is shipped in IMCCs, only a few specific commodities are shipped with enough frequency to present potential issues in screening IMCCs at ports. The majority of containers with NORM will contain fertilizers (5,700 containers), granite (59,000 containers), or ceramic (225,000 containers) materials. Fertilizers were generally shipping in either 20- or 40 ft containers with equal frequency. While granite is mostly shipped in 20 ft containers, ceramic materials can be shipped in either 20- or 40 ft containers. The size of container depended on the specific use of the ceramic or porcelain material. General construction ceramics (such as floor and roofing

  14. Analysis of International Commodity Shipping Data and the Shipment of NORM to the United States

    Baciak, James E.; Ely, James H.; Schweppe, John E.; Sandness, Gerald A.; Robinson, Sean M.

    2011-01-01

    As part of the Spreader Bar Radiation Detector project, PNNL analyzed US import data shipped through US ports collected over the 12 months of 2006 (over 4.5 million containers). Using these data, we extracted a variety of distributions that are of interest to modelers and developers of active and passive detection systems used to 'scan' IMCCs for potential contraband. This report expands on some of the analysis presented in an earlier report from LLNL, by investigation the foreign port distribution of commodities shipped to the US. The majority of containers shipped to the United States are 40 ft containers (∼70%); about 25% are 20 ft; and about 3.6% are 45 ft containers. A small fraction (<1%) of containers are of other more specialized sizes, and very few ports actually ship these unique size containers (a full distribution for all foreign ports is shown in Appendix A below). The primary foreign ports that ship the largest fraction of each container are shown in the table below. Given that 45 ft containers comprise 1 of out every 27 containers shipped to the US, and given the foreign ports from which they are shipped, they should not be ignored in screening; further testing and analysis of radiation measurements for national security with this size container is warranted. While a large amount of NORM is shipped in IMCCs, only a few specific commodities are shipped with enough frequency to present potential issues in screening IMCCs at ports. The majority of containers with NORM will contain fertilizers (5,700 containers), granite (59,000 containers), or ceramic (225,000 containers) materials. Fertilizers were generally shipping in either 20- or 40 ft containers with equal frequency. While granite is mostly shipped in 20 ft containers, ceramic materials can be shipped in either 20- or 40 ft containers. The size of container depended on the specific use of the ceramic or porcelain material. General construction ceramics (such as floor and roofing tiles) tend to

  15. CFD investigation of pentamaran ship model with chine hull form on the resistance characteristics

    Yanuar; Sulistyawati, W.

    2018-03-01

    This paper presents an investigation of pentamaran hull form with chine hull form to the effects of outriggers position, asymmetry, and deadrise angles on the resistance characteristics. The investigation to the resistance characteristics by modelling pentamaran hull form using chine with symmetrical main hull and asymmetric outboard on the variation deadrise angles: 25°, 30°, 35° and Froude number 0,1 to 0,7. On calm water resistance characteristics of six pentamaran models with chine-hull form examined by variation of deadrise angles by using CFD. Comparation with Wigley hull form, the maximum resistance drag reduction of the chine hull form was reduced by 15.81% on deadrise 25°, 13.8% on deadrise 30°, and 20.38% on deadrise 35°. While the smallest value of total resistance coefficient was generated from chine 35° at R/L:1/14 and R/L:1/7. Optimum hull form for minimum resistance has been obtained, so it is interesting to continue with angle of entrance and stem angle of hull for further research.

  16. The Vessel Schedule Recovery Problem (VSRP) – A MIP model for handling disruptions in liner shipping

    Brouer, Berit Dangaard; Dirksen, Jakob; Pisinger, David

    2013-01-01

    or even omitting one. We present the Vessel Schedule Recovery Problem (VSRP) to evaluate a given disruption scenario and to select a recovery action balancing the trade off between increased bunker consumption and the impact on cargo in the remaining network and the customer service level. It is proven...... due to adverse weather conditions, port contingencies, and many other issues. A common scenario for recovering a schedule is to either increase the speed at the cost of a significant increase in the fuel consumption or delaying cargo. Advanced recovery options might exist by swapping two port calls...... that the VSRP is NP-hard. The model is applied to four real life cases from Maersk Line and results are achieved in less than 5seconds with solutions comparable or superior to those chosen by operations managers in real life. Cost savings of up to 58% may be achieved by the suggested solutions compared...

  17. Wind loads on post-panamax container ship

    Andersen, Ingrid Marie Vincent

    2013-01-01

    An investigation of the influence of the container configuration on the deck of a 9000+ TEU container ship on wind forces has been carried out through a series of wind tunnel tests with a 1:450 scale model. An analysis of earlier studies was used to select a series of appropriate loading conditions...

  18. Model test of boson mappings

    Navratil, P.; Dobes, J.

    1992-01-01

    Methods of boson mapping are tested in calculations for a simple model system of four protons and four neutrons in single-j distinguishable orbits. Two-body terms in the boson images of the fermion operators are considered. Effects of the seniority v=4 states are thus included. The treatment of unphysical states and the influence of boson space truncation are particularly studied. Both the Dyson boson mapping and the seniority boson mapping as dictated by the similarity transformed Dyson mapping do not seem to be simply amenable to truncation. This situation improves when the one-body form of the seniority image of the quadrupole operator is employed. Truncation of the boson space is addressed by using the effective operator theory with a notable improvement of results

  19. Fabrication of nuclear ship reactor MRX model and study on inspection and maintenance of components

    Kasahara, Yoshiyuki; Nakazawa, Toshio; Kusunoki, Tsuyoshi; Takahashi, Hiroki; Yoritsune, Tsutomu.

    1997-10-01

    The MRX (Marine Reactor X) is an integral type small reactor adopting passive safety systems. As for an integral type reactor, primary system components are installed in the reactor vessel. It is therefor important to establish the appropriate procedure for construction, inspection and maintenance, dismauntling, etc., for all components in the reactor vessel as well as in the reactor containment, because inspection space is limited. To study these subjects, a one-fifth model of the MRX was fabricated and operation capabilities were studied. As a result of studies, the following results are obtained. (1) Manufacturing and installing problems of the reactor pressure vessel, the containment vessel and internal components are basically not abserved. (2) Heat transfer tube structures of the steam generator and the heat exchangers of emergency decay heat removal system and containment water cooler were not seen of any problem for fabrication. However, due consideration is required in the detailed design of supports of heat transfer tubes. (3) Further studies should be needed for designs of flange penetrations and leak countermeasures for pipes instrument cables. (4) Arrangements of equipments in the containment should be taken in consideration in detail because the space is narrow. (5) Further discussion is required for installation methods of instruments and cables. (author)

  20. Antecedent characteristics of online cancer information seeking among rural breast cancer patients: an application of the Cognitive-Social Health Information Processing (C-SHIP) model.

    Shaw, Bret R; Dubenske, Lori L; Han, Jeong Yeob; Cofta-Woerpel, Ludmila; Bush, Nigel; Gustafson, David H; McTavish, Fiona

    2008-06-01

    Little research has examined the antecedent characteristics of patients most likely to seek online cancer information. This study employs the Cognitive-Social Health Information Processing (C-SHIP) model as a framework to understand what psychosocial characteristics precede online cancer-related information seeking among rural breast cancer patients who often have fewer health care providers and limited local support services. Examining 144 patients who were provided free computer hardware, Internet access, and training for how to use an interactive cancer communication system, pretest survey scores indicating patients' psychosocial status were correlated with specific online cancer information seeking behaviors. Each of the factors specified by the C-SHIP model had significant relationships with online cancer information seeking behaviors, with the strongest findings emerging for cancer-relevant encodings and self-construals, cancer-relevant beliefs and expectancies, and cancer-relevant self-regulatory competencies and skills. Specifically, patients with more negative appraisals in these domains were more likely to seek out online cancer information. Additionally, antecedent variables associated with the C-SHIP model had more frequent relationships with experiential information as compared with to didactic information. This study supports the applicability of the model to discern why people afflicted with cancer may seek online information to cope with their disease.

  1. Wind and Current Forces Acting on Canadian Forces Ships During Tug Operations

    2002-11-01

    McTaggart and Sav- age [1] describe model tests conducted on a generic frigate model to determine wind forces influencing ship capsize. Van Manen and van ...Fn will be 0.06. Based on data presented by van Manen and van Oossanen [2], the fric- tional resistance coefficient will be approximately 0.002 and...Conference on Stability of Ships and Ocean Vehicles (Melbourne, Florida, 1994). 2. J.D. van Manen and P. van Oossanen, Principles of Naval Architecture, Volume

  2. Auxiliary facilities on nuclear ship 'MUTSU'

    Tsujimura, Shotaro; Takigami, Yoshio.

    1989-01-01

    The nuclear ship 'MUTSU' has been moored at SEKINEHAMA, MUTU City in AOMORI Prefecture and several tests and works are being carried out on the ship. The construction of the auxiliary facilities for these works on the ship was completed in safety in August 1988. After that the facilities have fulfilled their function. The outlines of design, fabrication and construction of the facilities are described in this paper. (author)

  3. Thyroid function tests in patients taking thyroid medication in Germany: Results from the population-based Study of Health in Pomerania (SHIP

    Hannemann Anke

    2010-08-01

    Full Text Available Abstract Background Studies from iodine-sufficient areas have shown that a high proportion of patients taking medication for thyroid diseases have thyroid stimulating hormone (TSH levels outside the reference range. Next to patient compliance, inadequate dosing adjustment resulting in under- and over-treatment of thyroid disease is a major cause of poor therapy outcomes. Using thyroid function tests, we aim to measure the proportions of subjects, who are under- or over-treated with thyroid medication in a previously iodine-deficient area. Findings Data from 266 subjects participating in the population-based Study of Health in Pomerania (SHIP were analysed. All subjects were taking thyroid medication. Serum TSH levels were measured using immunochemiluminescent procedures. TSH levels of 2.15 mIU/L in subjects younger than 50 years and 2.09 mIU/L in subjects 50 years and older, were defined as decreased or elevated, according to the established reference range for the specific study area. Our analysis revealed that 56 of 190 (29.5% subjects treated with thyroxine had TSH levels outside the reference range (10.0% elevated, 19.5% decreased. Of the 31 subjects taking antithyroid drugs, 12 (38.7% had TSH levels outside the reference range (9.7% elevated, 29.0% decreased. These proportions were lower in the 45 subjects receiving iodine supplementation (2.2% elevated, 8.9% decreased. Among the 3,974 SHIP participants not taking thyroid medication, TSH levels outside the reference range (2.8% elevated, 5.9% decreased were less frequent. Conclusion In concordance with previous studies in iodine-sufficient areas, our results indicate that a considerable number of patients taking thyroid medication are either under- or over-treated. Improved monitoring of these patients' TSH levels, compared to the local reference range, is recommended.

  4. Thyroid function tests in patients taking thyroid medication in Germany: Results from the population-based Study of Health in Pomerania (SHIP).

    Hannemann, Anke; Friedrich, Nele; Haring, Robin; Krebs, Alexander; Völzke, Henry; Alte, Dietrich; Nauck, Matthias; Kohlmann, Thomas; Schober, Hans-Christof; Hoffmann, Wolfgang; Wallaschofski, Henri

    2010-08-16

    Studies from iodine-sufficient areas have shown that a high proportion of patients taking medication for thyroid diseases have thyroid stimulating hormone (TSH) levels outside the reference range. Next to patient compliance, inadequate dosing adjustment resulting in under- and over-treatment of thyroid disease is a major cause of poor therapy outcomes. Using thyroid function tests, we aim to measure the proportions of subjects, who are under- or over-treated with thyroid medication in a previously iodine-deficient area. Data from 266 subjects participating in the population-based Study of Health in Pomerania (SHIP) were analysed. All subjects were taking thyroid medication. Serum TSH levels were measured using immunochemiluminescent procedures. TSH levels of 2.15 mIU/L in subjects younger than 50 years and 2.09 mIU/L in subjects 50 years and older, were defined as decreased or elevated, according to the established reference range for the specific study area. Our analysis revealed that 56 of 190 (29.5%) subjects treated with thyroxine had TSH levels outside the reference range (10.0% elevated, 19.5% decreased). Of the 31 subjects taking antithyroid drugs, 12 (38.7%) had TSH levels outside the reference range (9.7% elevated, 29.0% decreased). These proportions were lower in the 45 subjects receiving iodine supplementation (2.2% elevated, 8.9% decreased). Among the 3,974 SHIP participants not taking thyroid medication, TSH levels outside the reference range (2.8% elevated, 5.9% decreased) were less frequent. In concordance with previous studies in iodine-sufficient areas, our results indicate that a considerable number of patients taking thyroid medication are either under- or over-treated. Improved monitoring of these patients' TSH levels, compared to the local reference range, is recommended.

  5. Development of the nuclear ship MUTSU spent fuel shipping cask

    Ishizuka, M.; Umeda, M.; Nawata, Y.; Sato, H.; Honami, M.; Nomura, T.; Ohashi, M.; Higashino, A.

    1989-01-01

    After the planned trial voyage (4700 MWD/MTU) of the nuclear ship MUTSU in 1990, her spent fuel assemblies, initially made of two types of enriched UO 2 (3.2wt% and 4.4wt%), will be transferred to the reprocessing plant soon after cooling down in the ship reactor for more than one year. For transportation, the MUTSU spent fuel shipping casks will be used. Prior to transportation to the reprocessing plant, the cooled spent fuel assemblies will be removed from the reactor to the shipping casks and housed at the spent fuel storage facility on site. In designing the MUTSU spent fuel shipping cask, considerations were given to make the leak-tightness and integrity of the cask confirmable during storage. The development of the cask and the storage function demonstration test were performed by Japan Atomic Energy Research Institute (JAERI) and Mitsubishi Heavy Industries, Ltd. (MHI). One prototype cask for the storage demonstration test and licensed thirty-five casks were manufactured between 1987 and 1988

  6. Thermal Testing and Model Correlation for Advanced Topographic Laser Altimeter Instrument (ATLAS)

    Patel, Deepak

    2016-01-01

    The Advanced Topographic Laser Altimeter System (ATLAS) part of the Ice Cloud and Land Elevation Satellite 2 (ICESat-2) is an upcoming Earth Science mission focusing on the effects of climate change. The flight instrument passed all environmental testing at GSFC (Goddard Space Flight Center) and is now ready to be shipped to the spacecraft vendor for integration and testing. This topic covers the analysis leading up to the test setup for ATLAS thermal testing as well as model correlation to flight predictions. Test setup analysis section will include areas where ATLAS could not meet flight like conditions and what were the limitations. Model correlation section will walk through changes that had to be made to the thermal model in order to match test results. The correlated model will then be integrated with spacecraft model for on-orbit predictions.

  7. Underactuated ship tracking control : theory and experiments

    Pettersen, K.Y.; Nijmeijer, H.

    2001-01-01

    We consider complete state tracking feedback control of a ship having two controls, namely surge force and yaw moment. The ship model has similarities with chained form systems but cannot directly be transformed in chained form. In particular, the model has a drift vector field as opposed to the

  8. Guide to ship sanitation

    2011-01-01

    "The third edition of the Guide to Ship Sanitation presents the public health significance of ships in terms of disease and highlights the importance of applying appropriate control measures"--Back cover...

  9. Recycling of merchant ships

    Magdalena Klopott

    2013-12-01

    Full Text Available The article briefly outlines the issues concerning ship recycling. It highlights ships' high value as sources of steel scrap and non-ferrous metals, without omitting the fact that they also contain a range of hazardous substances. Moreover, the article also focuses on basic ship demolition methods and their environmental impact, as well as emphasizes the importance of “design for ship recycling” philosophy.

  10. Wave basin model tests of technical-biological bank protection

    Eisenmann, J.

    2012-04-01

    Sloped embankments of inland waterways are usually protected from erosion and other negative im-pacts of ship-induced hydraulic loads by technical revetments consisting of riprap. Concerning the dimensioning of such bank protection there are several design rules available, e.g. the "Principles for the Design of Bank and Bottom Protection for Inland Waterways" or the Code of Practice "Use of Standard Construction Methods for Bank and Bottom Protection on Waterways" issued by the BAW (Federal Waterways Engineering and Research Institute). Since the European Water Framework Directive has been put into action special emphasis was put on natural banks. Therefore the application of technical-biological bank protection is favoured. Currently design principles for technical-biological bank protection on inland waterways are missing. The existing experiences mainly refer to flowing waters with no or low ship-induced hydraulic loads on the banks. Since 2004 the Federal Waterways Engineering and Research Institute has been tracking the re-search and development project "Alternative Technical-Biological Bank Protection on Inland Water-ways" in company with the Federal Institute of Hydrology. The investigation to date includes the ex-amination of waterway sections where technical- biological bank protection is applied locally. For the development of design rules for technical-biological bank protection investigations shall be carried out in a next step, considering the mechanics and resilience of technical-biological bank protection with special attention to ship-induced hydraulic loads. The presentation gives a short introduction into hydraulic loads at inland waterways and their bank protection. More in detail model tests of a willow brush mattress as a technical-biological bank protec-tion in a wave basin are explained. Within the scope of these tests the brush mattresses were ex-posed to wave impacts to determine their resilience towards hydraulic loads. Since the

  11. 9 m side drop test of scale model

    Ku, Jeong-Hoe; Chung, Seong-Hwan; Lee, Ju-Chan; Seo, Ki-Seog

    1993-01-01

    A type B(U) shipping cask had been developed in KAERI for transporting PWR spent fuel. Since the cask is to transport spent PWR fuel, it must be designed to meet all of the structural requirements specified in domestic packaging regulations and IAEA safety series No.6. This paper describes the side drop testing of a one - third scale model cask. The crush and deformations of the shock absorbing covers directly control the deceleration experiences of the cask during the 9 m side drop impact. The shock absorbing covers greatly mitigated the inertia forces of the cask body due to the side drop impact. Compared with the side drop test and finite element analysis, it was verified that the 1/3 scale model cask maintain its structural integrity of the model cask under the side drop impact. The test and analysis results could be used as the basic data to evaluate the structural integrity of the real cask. (J.P.N.)

  12. Dutch Ships and Sailors

    de Boer, Victor; Hoekstra, F.G.; Leinenga, Jurjen; van Rossum, Matthias

    2014-01-01

    Dutch Ships and Sailors provides an infrastructure for maritime historical datasets, linking correlating data through semantic web technology. It brings together datasets related to recruitment and shipping in the East-India trade (mainly 18th century) and in the shipping of the northern provinces

  13. Reactors. Nuclear propulsion ships

    Fribourg, Ch.

    2001-01-01

    This article has for object the development of nuclear-powered ships and the conception of the nuclear-powered ship. The technology of the naval propulsion P.W.R. type reactor is described in the article B.N.3 141 'Nuclear Boilers ships'. (N.C.)

  14. Model-based testing for software safety

    Gurbuz, Havva Gulay; Tekinerdogan, Bedir

    2017-01-01

    Testing safety-critical systems is crucial since a failure or malfunction may result in death or serious injuries to people, equipment, or environment. An important challenge in testing is the derivation of test cases that can identify the potential faults. Model-based testing adopts models of a

  15. Superconducting magnets for model ship propulsion and for material tests of a nuclear fusion reactor

    Horiuchi, T.; Matsumoto, K.; Monju, Y.; Tatara, I.; Hamada, M.

    1982-01-01

    Nuclear fusion reactors, magnetically levitated trains, and MHD generators, etc., all need a very high magnetic field; which in order to be attained a means the application of superconductors is inevitable. This paper describes the development of ''CRYOZITT'', a superconductor featuring high current density and high mechanical strength. CRYOZITT has already been used in the manufacture of two race-track shaped superconducting magnets, and delivered to highly satisfied customers. (author)

  16. Reliability Based Ship Structural Design

    Dogliani, M.; Østergaard, C.; Parmentier, G.

    1996-01-01

    This paper deals with the development of different methods that allow the reliability-based design of ship structures to be transferred from the area of research to the systematic application in current design. It summarises the achievements of a three-year collaborative research project dealing...... with developments of models of load effects and of structural collapse adopted in reliability formulations which aim at calibrating partial safety factors for ship structural design. New probabilistic models of still-water load effects are developed both for tankers and for containerships. New results are presented...... structure of several tankers and containerships. The results of the reliability analysis were the basis for the definition of a target safety level which was used to asses the partial safety factors suitable for in a new design rules format to be adopted in modern ship structural design. Finally...

  17. Positive matrix factorization and trajectory modelling for source identification: A new look at Indian Ocean Experiment ship observations

    Bhanuprasad, S. G.; Venkataraman, Chandra; Bhushan, Mani

    The sources of aerosols on a regional scale over India have only recently received attention in studies using back trajectory analysis and chemical transport modelling. Receptor modelling approaches such as positive matrix factorization (PMF) and the potential source contribution function (PSCF) are effective tools in source identification of urban and regional-scale pollution. In this work, PMF and PSCF analysis is applied to identify categories and locations of sources that influenced surface concentrations of aerosols in the Indian Ocean Experiment (INDOEX) domain measured on-board the research vessel Ron Brown [Quinn, P.K., Coffman, D.J., Bates, T.S., Miller, T.L., Johnson, J.E., Welton, E.J., et al., 2002. Aerosol optical properties during INDOEX 1999: means, variability, and controlling factors. Journal of Geophysical Research 107, 8020, doi:10.1029/2000JD000037]. Emissions inventory information is used to identify sources co-located with probable source regions from PSCF. PMF analysis identified six factors influencing PM concentrations during the INDOEX cruise of the Ron Brown including a biomass combustion factor (35-40%), three industrial emissions factors (35-40%), primarily secondary sulphate-nitrate, balance trace elements and Zn, and two dust factors (20-30%) of Si- and Ca-dust. The identified factors effectively predict the measured submicron PM concentrations (slope of regression line=0.90±0.20; R2=0.76). Probable source regions shifted based on changes in surface and elevated flows during different times in the ship cruise. They were in India in the early part of the cruise, but in west Asia, south-east Asia and Africa, during later parts of the cruise. Co-located sources include coal-fired electric utilities, cement, metals and petroleum production in India and west Asia, biofuel combustion for energy and crop residue burning in India, woodland/forest burning in north sub-Saharan Africa and forest burning in south-east Asia. Significant findings

  18. Ship emissions and air pollution in Denmark

    Olesen, Helge Rørdam; Winther, Morten; Ellermann, Thomas

    A project has been carried out to map the contribution from ship traffic to air pollution in Denmark. A main element in the project is the establishment of a new, improved inventory of ship emissions for the waters around Denmark. The inventory makes use of the so-called AIS system, which...... continuously keeps track of ship positions. The inventory provides basis for model calculations of air quality in Denmark for the years 2007, 2011 and 2020. The study has focus on identifying the contribution from ships, and on assessing the effect of international regulations of ship pollution. A minor...... component of the study concerns the contribution to local air pollution from ships at port....

  19. Nuclear merchant ship propulsion

    Schroeder, E.; Jager, W.; Schafstall, H.G.

    1977-01-01

    The operation of about 300 nuclear naval vessels has proven the feasibility of nuclear ship propulsion. Until now six non military ships have been built or are under construction. In the Soviet Union two nuclear icebreakers are in operation, and a third one is under construction. In the western world three prototype merchant ships have been built. Of these ships only the NS OTTO HAHN is in operation and provides valuable experience for future large scale use of nuclear merchant ship propulsion. In many countries studies and plans are made for future nuclear merchant ships. Types of vessels investigated are large containerships, tankers and specialized ships like icebreakers or ice-breaking ships. The future of nuclear merchant ship propulsion depends on three interrelated items: (1) nuclear ship technology; (2) economy of nuclear ship propulsion; (3) legal questions. Nuclear merchant ship technology is based until now on standard ship technology and light water reactor technology. Except for special questions due to the non-stationary type of the plant entirely new problems do not arise. This has been proven by the recent conceptual licensing procedure for a large nuclear containership in Germany. The economics of nuclear propulsion will be under discussion until they are proven by the operation of privately owned lead ships. Unsolved legal questions e.g. in connection with port entry permissions are at present another problem for nuclear shipping. Efforts are made to solve these questions on an international basis. The future development of nuclear energy electricity production in large land based plants will stimulate the employment of smaller units. Any future development of long distance sea transport will have to take this opportunity of a reliable and economic energy supply into account

  20. Detecting potential ship objects from satellite pictures

    Luo, B.; Yang, C.C.; Chang, S.K.; Yang, M.C.K.

    1984-01-01

    Heuristic techniques are presented to detect potential ship objects from satellite pictures. These techniques utilize some noise structures of the pixel gray levels, and certain inherent features of a ship in a satellite picture. The scheme has been implemented and successfully tested on SEASAT satellite pictures. A general approach for database-oriented object detection is also suggested

  1. Artificial neural network controller for automatic ship berthing using head-up coordinate system

    Nam-Kyun Im

    2018-05-01

    Full Text Available The Artificial Neural Network (ANN model has been known as one of the most effective theories for automatic ship berthing, as it has learning ability and mimics the actions of the human brain when performing the stages of ship berthing. However, existing ANN controllers can only bring a ship into a berth in a certain port, where the inputs of the ANN are the same as those of the teaching data. This means that those ANN controllers must be retrained when the ship arrives to a new port, which is time-consuming and costly. In this research, by using the head-up coordinate system, which includes the relative bearing and distance from the ship to the berth, a novel ANN controller is proposed to automatically control the ship into the berth in different ports without retraining the ANN structure. Numerical simulations were performed to verify the effectiveness of the proposed controller. First, teaching data were created in the original port to train the neural network; then, the controller was tested for automatic berthing in other ports, where the initial conditions of the inputs in the head-up coordinate system were similar to those of the teaching data in the original port. The results showed that the proposed controller has good performance for ship berthing in ports. Keywords: Automatic ship berthing, ANN controller, Head-up coordinate system, Low speed, Relative bearing

  2. Vehicle rollover sensor test modeling

    McCoy, R.W.; Chou, C.C.; Velde, R. van de; Twisk, D.; Schie, C. van

    2007-01-01

    A computational model of a mid-size sport utility vehicle was developed using MADYMO. The model includes a detailed description of the suspension system and tire characteristics that incorporated the Delft-Tyre magic formula description. The model was correlated by simulating a vehicle suspension

  3. Transnucleaire's experience in ship adaptation

    Brachet, Y.; Vallette-Fontaine, M.

    2000-01-01

    Due to the application of the new IMDG regulations for the transport of radioactive material by sea, the conditions of transport of MTR spent fuel have drastically changed five years ago. In this paper, TRANSNUCLEAIRE analyses the necessary modifications to apply to existing ships in order to comply with the IMDG/INF regulations as well as with the Japanese KAISA 520 regulation. In the MTR spent fuel transport market characterized by a competitive approach, TRANSNUCLEAIRE has carried out many transports by sea in full compliance with the regulations at a price which is as close as possible to that of other industrial goods and without the need to fully dedicate the BOUGUENAIS ship to nuclear transports. Innovative ship design solutions have been implemented and accepted by different Authorities uncluding the Advisory Committee of the Japanese MOT. Due to efficient finite element calculations, benchmarked by laboratory large scale tests, high performances crushing materials have been developed in order to absorb the energy of collision between ships. These developments have led ta propose an efficient ship design complying with all the existing worldwide nuclear regulations. (author)

  4. Testing of the Model 48-14 overpack for UF6 cylinders

    Stitt, D.H.

    1983-01-01

    Shipment of UF 6 enriched to 1.0% or greater assay 235 U currently is done in either the 30-B overpack or the Paducah tiger overpack. The former contains a 2-1/2 ton cylinder, 30 in. in diameter, while the latter contains a 10-ton cylinder, 48 in. in diameter. There are apparent economy and safety considerations associated with shipping in the larger containers due to the reduced number of shipments and connect and disconnect operations. Further reductions in connect and disconnect operations and shipping costs could be achieved through use of the 14-ton cylinder for shipment of enriched material. With this thought, a program was initiated in 1980 to develop a protective overpack for the Model 48Y cylinder. Two prototype overpacks of wood and stainless steel construction were fabricated. The results from the drop tests and the thermal exposure test are presented

  5. Development of a model for the prediction of the fuel consumption and nitrogen oxides emission trade-off for large ships

    Larsen, Ulrik; Pierobon, Leonardo; Baldi, Francesco

    2015-01-01

    The international regulations on fuel efficiency and NOx emissions of commercial ships motivate the investigation of new system layouts, which can comply with the regulations. In combustion engines, measures to reduce the fuel consumption often lead to increased NOx emissions and careful consider...... that increased system complexity can lead to lower fuel consumption and NOx. Fuel consumption reductions of up to 9% with a 6.5% NOx reduction were achieved using a hybrid turbocharger and organic Rankine cycle waste heat recovery system.......The international regulations on fuel efficiency and NOx emissions of commercial ships motivate the investigation of new system layouts, which can comply with the regulations. In combustion engines, measures to reduce the fuel consumption often lead to increased NOx emissions and careful...... consideration of this trade-off mechanism is required in the design of marine propulsion systems. This study investigates five different configurations of two-stroke diesel-based machinery systems for large ships and their influence on the mentioned trade-off. Numerical models of a low-speed two-stroke diesel...

  6. Engineering model cryocooler test results

    Skimko, M.A.; Stacy, W.D.; McCormick, J.A.

    1992-01-01

    This paper reports that recent testing of diaphragm-defined, Stirling-cycle machines and components has demonstrated cooling performance potential, validated the design code, and confirmed several critical operating characteristics. A breadboard cryocooler was rebuilt and tested from cryogenic to near-ambient cold end temperatures. There was a significant increase in capacity at cryogenic temperatures and the performance results compared will with code predictions at all temperatures. Further testing on a breadboard diaphragm compressor validated the calculated requirement for a minimum axial clearance between diaphragms and mating heads

  7. Naval Aerodynamics Test Facility (NATF)

    Federal Laboratory Consortium — The NATF specializes in Aerodynamics testing of scaled and fullsized Naval models, research into flow physics found on US Navy planes and ships, aerosol testing and...

  8. Climate and air quality trade-offs in altering ship fuel sulfur content

    Partanen, A.-I.; Laakso, A.; Schmidt, A.; Kokkola, H.; Kuokkanen, T.; Pietikäinen, J.-P.; Kerminen, V.-M.; Lehtinen, K. E. J.; Laakso, L.; Korhonen, H.

    2013-08-01

    Aerosol particles from shipping emissions both cool the climate and cause adverse health effects. The cooling effect is, however, declining because of shipping emission controls aiming to improve air quality. We used an aerosol-climate model ECHAM-HAMMOZ to test whether by altering ship fuel sulfur content, the present-day aerosol-induced cooling effect from shipping could be preserved while at the same time reducing premature mortality rates related to shipping emissions. We compared the climate and health effects of a present-day shipping emission scenario with (1) a simulation with strict emission controls in the coastal waters (ship fuel sulfur content of 0.1%) and twofold ship fuel sulfur content compared to current global average of 2.7% elsewhere; and (2) a scenario with global strict shipping emission controls (ship fuel sulfur content of 0.1% in coastal waters and 0.5% elsewhere) roughly corresponding to international agreements to be enforced by the year 2020. Scenario 1 had a slightly stronger aerosol-induced radiative flux perturbation (RFP) from shipping than the present-day scenario (-0.43 W m-2 vs. -0.39 W m-2) while reducing premature mortality from shipping by 69% (globally 34 900 deaths avoided per year). Scenario 2 decreased the RFP to -0.06 W m-2 and annual deaths by 96% (globally 48 200 deaths avoided per year) compared to present-day. A small difference in radiative effect (global mean of 0.04 W m-2) in the coastal regions between Scenario 1 and the present-day scenario imply that shipping emission regulation in the existing emission control areas should not be removed in hope of climate cooling. Our results show that the cooling effect of present-day emissions could be retained with simultaneous notable improvements in air quality, even though the shipping emissions from the open ocean clearly have a significant effect on continental air quality. However, increasing ship fuel sulfur content in the open ocean would violate existing

  9. Virtual Ship Architecture Description Document Issue 1.00

    Best, John

    2000-01-01

    The Virtual Ship concept calls for simulation models of systems to be brought together to create a virtual representation of a warship, in a process analogous to the construction of a physical ship...

  10. The mechanics of ship impacts against bridges

    Pedersen, Preben Terndrup; Zhang, Shengming

    1998-01-01

    a glancing blow between the ship and the bridge structure. This model is based on rigid body mechanics and well suited for inclusion in a probabilistic analysis procedure. Finally, some empirical expressions are presented which relate the energy absorbed by crushing of ship structures to the maximum impact...

  11. Routing and scheduling and fleet management for liner shipping

    Kjeldsen, Karina Hjortshøj

    2009-01-01

    The problem of routing, scheduling and fleet management in global liner shipping is presented. The developed model incorporates the ships' speed as a decision variable. Furthermore, the model must be able to handle problems of the size and complexity experienced by the global liner shipping...

  12. On Grounding of Fast Ships

    Simonsen, Bo Cerup; Pedersen, Preben Terndrup

    1997-01-01

    The paper deals with analysis of grounding of high-speed crafts. It is the purpose to present a comprehensive mathematical model for calculation of the overall dynamic ship response during grounding. This procedure is applied to derive the motions, the time varying sectional forces and the local...... loads during grounding on plane, sloping, sandy bottoms for six different designs of fast monohull ships made from steel, aluminium or GRP sandwich materials. The results show that the effect of the hull flexibility is to reduce the overall dynamic sectional loads on the hull girder. The considered...... numerical examples also indicate that, even with impact speeds of 40 knots against a 1:10 sloping bottom, the global strength of the hull girder is not exceeded by the grounding induced loads.For the local deformation of high-speed ship hulls at the point of contact with the ground, the paper presents...

  13. Testing homogeneity in Weibull-regression models.

    Bolfarine, Heleno; Valença, Dione M

    2005-10-01

    In survival studies with families or geographical units it may be of interest testing whether such groups are homogeneous for given explanatory variables. In this paper we consider score type tests for group homogeneity based on a mixing model in which the group effect is modelled as a random variable. As opposed to hazard-based frailty models, this model presents survival times that conditioned on the random effect, has an accelerated failure time representation. The test statistics requires only estimation of the conventional regression model without the random effect and does not require specifying the distribution of the random effect. The tests are derived for a Weibull regression model and in the uncensored situation, a closed form is obtained for the test statistic. A simulation study is used for comparing the power of the tests. The proposed tests are applied to real data sets with censored data.

  14. The Model Identification Test: A Limited Verbal Science Test

    McIntyre, P. J.

    1972-01-01

    Describes the production of a test with a low verbal load for use with elementary school science students. Animated films were used to present appropriate and inappropriate models of the behavior of particles of matter. (AL)

  15. Theoretical Models, Assessment Frameworks and Test Construction.

    Chalhoub-Deville, Micheline

    1997-01-01

    Reviews the usefulness of proficiency models influencing second language testing. Findings indicate that several factors contribute to the lack of congruence between models and test construction and make a case for distinguishing between theoretical models. Underscores the significance of an empirical, contextualized and structured approach to the…

  16. Achieving Energy Efficient Ship Operations Under Third Party Management

    Taudal Poulsen, René; Sornn-Friese, Henrik

    2015-01-01

    Profitable energy saving measures are often not fully implemented in shipping, causing energy efficiency gaps. The paper identifies energy efficiency gaps in ship operations, and explores their causes. Lack of information on energy efficiency, lack of energy training at sea and onshore and lack...... of time to produce and provide reliable energy efficiency information cause energy efficiency gaps. The paper brings together the energy efficiency and ship management literatures, demonstrating how ship management models influence energy efficiency in ship operations. Achieving energy efficiency in ship...

  17. Geochemical Testing And Model Development - Residual Tank Waste Test Plan

    Cantrell, K.J.; Connelly, M.P.

    2010-01-01

    This Test Plan describes the testing and chemical analyses release rate studies on tank residual samples collected following the retrieval of waste from the tank. This work will provide the data required to develop a contaminant release model for the tank residuals from both sludge and salt cake single-shell tanks. The data are intended for use in the long-term performance assessment and conceptual model development.

  18. Hydraulic Model Tests on Modified Wave Dragon

    Hald, Tue; Lynggaard, Jakob

    A floating model of the Wave Dragon (WD) was built in autumn 1998 by the Danish Maritime Institute in scale 1:50, see Sørensen and Friis-Madsen (1999) for reference. This model was subjected to a series of model tests and subsequent modifications at Aalborg University and in the following...... are found in Hald and Lynggaard (2001). Model tests and reconstruction are carried out during the phase 3 project: ”Wave Dragon. Reconstruction of an existing model in scale 1:50 and sequentiel tests of changes to the model geometry and mass distribution parameters” sponsored by the Danish Energy Agency...

  19. A model for optimal constrained adaptive testing

    van der Linden, Willem J.; Reese, Lynda M.

    2001-01-01

    A model for constrained computerized adaptive testing is proposed in which the information on the test at the ability estimate is maximized subject to a large variety of possible constraints on the contents of the test. At each item-selection step, a full test is first assembled to have maximum

  20. A model for optimal constrained adaptive testing

    van der Linden, Willem J.; Reese, Lynda M.

    1997-01-01

    A model for constrained computerized adaptive testing is proposed in which the information in the test at the ability estimate is maximized subject to a large variety of possible constraints on the contents of the test. At each item-selection step, a full test is first assembled to have maximum

  1. Traceability in Model-Based Testing

    Mathew George

    2012-11-01

    Full Text Available The growing complexities of software and the demand for shorter time to market are two important challenges that face today’s IT industry. These challenges demand the increase of both productivity and quality of software. Model-based testing is a promising technique for meeting these challenges. Traceability modeling is a key issue and challenge in model-based testing. Relationships between the different models will help to navigate from one model to another, and trace back to the respective requirements and the design model when the test fails. In this paper, we present an approach for bridging the gaps between the different models in model-based testing. We propose relation definition markup language (RDML for defining the relationships between models.

  2. Real-Time Simulation of Ship-Structure and Ship-Ship Interaction

    Lindberg, Ole; Glimberg, Stefan Lemvig; Bingham, Harry B.

    2013-01-01

    , because it is simple, easy to implement and computationally efficient. Multiple many-core graphical processing units (GPUs) are used for parallel execution and the model is implemented using a combination of C/C++, CUDA and MPI. Two ship hydrodynamic cases are presented: Kriso Container Carrier at steady...

  3. Review of a model to assess stranding of juvenile salmon by ship wakes along the Lower Columbia River, Oregon and Washington

    Kock, Tobias J.; Plumb, John M.; Adams, Noah S.

    2013-01-01

    Long period wake waves from deep draft vessels have been shown to strand small fish, particularly juvenile Chinook salmon Oncorhynchus tschawytcha, in the lower Columbia River (LCR). The U.S. Army Corps of Engineers is responsible for maintaining the shipping channel in the LCR and recently conducted dredging operations to deepen the shipping channel from an authorized depth of 40 feet(ft) to an authorized depth of 43 ft (in areas where rapid shoaling was expected, dredging operations were used to increase the channel depth to 48 ft). A model was developed to estimate stranding probabilities for juvenile salmon under the 40- and 43-ft channel scenarios, to determine if channel deepening was going to affect wake stranding (Assessment of potential stranding of juvenile salmon by ship wakes along the Lower Columbia River under scenarios of ship traffic and channel depth: Report prepared for the Portland District U.S. Army Corps of Engineers, Portland, Oregon). The U.S. Army Corps of Engineers funded the U.S. Geological Survey to review this model. A total of 30 review questions were provided to guide the review process, and these questions are addressed in this report. In general, we determined that the analyses by Pearson (2011) were appropriate given the data available. We did identify two areas where additional information could have been provided: (1) a more thorough description of model diagnostics and model selection would have been useful for the reader to better understand the model framework; and (2) model uncertainty should have been explicitly described and reported in the document. Stranding probability estimates between the 40- and 43-ft channel depths were minimally different under most of the scenarios that were examined by Pearson (2011), and a discussion of the effects of uncertainty given these minimal differences would have been useful. Ultimately, however, a stochastic (or simulation) model would provide the best opportunity to illustrate

  4. Buckling of Ship Structures

    Shama, Mohamed

    2013-01-01

    Buckling of Ship Structures presents a comprehensive analysis of the buckling problem of ship structural members. A full analysis of the various types of loadings and stresses imposed on ship plating and primary and secondary structural members is given. The main causes and consequences of the buckling mode of failure of ship structure and the methods commonly used to control buckling failure are clarified. This book contains the main equations required to determine the critical buckling stresses for both ship plating and the primary and secondary stiffening structural members. The critical buckling stresses are given for ship plating subjected to the induced various types of loadings and having the most common boundary conditions encountered in ship structures.  The text bridges the gap existing in most books covering the subject of buckling of ship structures in the classical analytical format, by putting the emphasis on the practical methods required to ensure safety against buckling of ship structur...

  5. Test facility TIMO for testing the ITER model cryopump

    Haas, H.; Day, C.; Mack, A.; Methe, S.; Boissin, J.C.; Schummer, P.; Murdoch, D.K.

    2001-01-01

    Within the framework of the European Fusion Technology Programme, FZK is involved in the research and development process for a vacuum pump system of a future fusion reactor. As a result of these activities, the concept and the necessary requirements for the primary vacuum system of the ITER fusion reactor were defined. Continuing that development process, FZK has been preparing the test facility TIMO (Test facility for ITER Model pump) since 1996. This test facility provides for testing a cryopump all needed infrastructure as for example a process gas supply including a metering system, a test vessel, the cryogenic supply for the different temperature levels and a gas analysing system. For manufacturing the ITER model pump an order was given to the company L' Air Liquide in the form of a NET contract. (author)

  6. Test facility TIMO for testing the ITER model cryopump

    Haas, H.; Day, C.; Mack, A.; Methe, S.; Boissin, J.C.; Schummer, P.; Murdoch, D.K.

    1999-01-01

    Within the framework of the European Fusion Technology Programme, FZK is involved in the research and development process for a vacuum pump system of a future fusion reactor. As a result of these activities, the concept and the necessary requirements for the primary vacuum system of the ITER fusion reactor were defined. Continuing that development process, FZK has been preparing the test facility TIMO (Test facility for ITER Model pump) since 1996. This test facility provides for testing a cryopump all needed infrastructure as for example a process gas supply including a metering system, a test vessel, the cryogenic supply for the different temperature levels and a gas analysing system. For manufacturing the ITER model pump an order was given to the company L'Air Liquide in the form of a NET contract. (author)

  7. Statistical Tests for Mixed Linear Models

    Khuri, André I; Sinha, Bimal K

    2011-01-01

    An advanced discussion of linear models with mixed or random effects. In recent years a breakthrough has occurred in our ability to draw inferences from exact and optimum tests of variance component models, generating much research activity that relies on linear models with mixed and random effects. This volume covers the most important research of the past decade as well as the latest developments in hypothesis testing. It compiles all currently available results in the area of exact and optimum tests for variance component models and offers the only comprehensive treatment for these models a

  8. Ships - inspiring objects in architecture

    Marczak, Elzbieta

    2017-10-01

    Sea-going vessels have for centuries fascinated people, not only those who happen to work at sea, but first and foremost, those who have never set foot aboard a ship. The environment in which ships operate is reminiscent of freedom and countless adventures, but also of hard and interesting maritime working life. The famous words of Pompey: “Navigare necesseest, vivere non estnecesse” (sailing is necessary, living - is not necessary), which he pronounced on a stormy sea voyage, arouse curiosity and excitement, inviting one to test the truth of this saying personally. It is often the case, however, that sea-faring remains within the realm of dreams, while the fascination with ships demonstrates itself through a transposition of naval features onto land constructions. In such cases, ship-inspired motifs bring alive dreams and yearnings as well as reflect tastes. Tourism is one of the indicators of people’s standard of living and a measure of a society’s civilisation. Maritime tourism has been developing rapidly in recent decades. A sea cruise offers an insight into life at sea. Still, most people derive their knowledge of passenger vessels and their furnishings from the mass media. Passenger vessels, also known as “floating cities,” are described as majestic and grand, while their on-board facilities as luxurious, comfortable, exclusive and inaccessible to common people on land. Freight vessels, on the other hand, are described as enormous objects which dwarf the human being into insignificance. This article presents the results of research intended to answer the following questions: what makes ships a source of inspiration for land architecture? To what extent and by what means do architects draw on ships in their design work? In what places can we find structures inspired by ships? What ships inspire architects? This article presents examples of buildings, whose design was inspired by the architecture and structural details of sea vessels. An analysis of

  9. Results of steel containment vessel model test

    Luk, V.K.; Ludwigsen, J.S.; Hessheimer, M.F.; Komine, Kuniaki; Matsumoto, Tomoyuki; Costello, J.F.

    1998-05-01

    A series of static overpressurization tests of scale models of nuclear containment structures is being conducted by Sandia National Laboratories for the Nuclear Power Engineering Corporation of Japan and the US Nuclear Regulatory Commission. Two tests are being conducted: (1) a test of a model of a steel containment vessel (SCV) and (2) a test of a model of a prestressed concrete containment vessel (PCCV). This paper summarizes the conduct of the high pressure pneumatic test of the SCV model and the results of that test. Results of this test are summarized and are compared with pretest predictions performed by the sponsoring organizations and others who participated in a blind pretest prediction effort. Questions raised by this comparison are identified and plans for posttest analysis are discussed

  10. lmerTest Package: Tests in Linear Mixed Effects Models

    Kuznetsova, Alexandra; Brockhoff, Per B.; Christensen, Rune Haubo Bojesen

    2017-01-01

    One of the frequent questions by users of the mixed model function lmer of the lme4 package has been: How can I get p values for the F and t tests for objects returned by lmer? The lmerTest package extends the 'lmerMod' class of the lme4 package, by overloading the anova and summary functions...... by providing p values for tests for fixed effects. We have implemented the Satterthwaite's method for approximating degrees of freedom for the t and F tests. We have also implemented the construction of Type I - III ANOVA tables. Furthermore, one may also obtain the summary as well as the anova table using...

  11. Field testing of bioenergetic models

    Nagy, K.A.

    1985-01-01

    Doubly labeled water provides a direct measure of the rate of carbon dioxide production by free-living animals. With appropriate conversion factors, based on chemical composition of the diet and assimilation efficiency, field metabolic rate (FMR), in units of energy expenditure, and field feeding rate can be estimated. Validation studies indicate that doubly labeled water measurements of energy metabolism are accurate to within 7% in reptiles, birds, and mammals. This paper discusses the use of doubly labeled water to generate empirical models for FMR and food requirements for a variety of animals

  12. Linear Logistic Test Modeling with R

    Baghaei, Purya; Kubinger, Klaus D.

    2015-01-01

    The present paper gives a general introduction to the linear logistic test model (Fischer, 1973), an extension of the Rasch model with linear constraints on item parameters, along with eRm (an R package to estimate different types of Rasch models; Mair, Hatzinger, & Mair, 2014) functions to estimate the model and interpret its parameters. The…

  13. Japan nuclear ship sea trial

    Yamazaki, Hiroshi; Kitamura, Toshikatus; Mizushima, Toshihiko

    1992-01-01

    The sea trial of the first Japan nuclear Ship 'MUTSU' was conducted from the end of October to December in 1990. The purpose of the sea trial was to verify the nuclear propulsive performances and maneuverabilities. The present report describes the results of the sea trial. These results are classified into four items: 1. Speed test and engineering performance tests 2. Maneuvering performance tests 3. Vibration tests 4. Other tests. Acceptable performances were demonstrated, as expected in the original design. The experience of the use of the Global Positioning System (GPS), which were newly adopted for the sea trial, is also reported. (author)

  14. TESTING GARCH-X TYPE MODELS

    Pedersen, Rasmus Søndergaard; Rahbek, Anders

    2017-01-01

    We present novel theory for testing for reduction of GARCH-X type models with an exogenous (X) covariate to standard GARCH type models. To deal with the problems of potential nuisance parameters on the boundary of the parameter space as well as lack of identification under the null, we exploit...... a noticeable property of specific zero-entries in the inverse information of the GARCH-X type models. Specifically, we consider sequential testing based on two likelihood ratio tests and as demonstrated the structure of the inverse information implies that the proposed test neither depends on whether...... the nuisance parameters lie on the boundary of the parameter space, nor on lack of identification. Our general results on GARCH-X type models are applied to Gaussian based GARCH-X models, GARCH-X models with Student's t-distributed innovations as well as the integer-valued GARCH-X (PAR-X) models....

  15. Experimental and Numerical Analysis of Hull Girder Vibrations and Bow Impact of a Large Ship Sailing in Waves

    Jialong Jiao

    2015-01-01

    Full Text Available It is of great importance to evaluate the hull structural vibrations response of large ships in extreme seas. Studies of hydroelastic response of an ultra large ship have been conducted with comparative verification between experimental and numerical methods in order to estimate the wave loads response considering hull vibration and water impact. A segmented self-propelling model with steel backbone system was elaborately designed and the experiments were performed in a tank. Time domain numerical simulations of the ship were carried out by using three-dimensional nonlinear hydroelasticity theory. The results from the computational analyses have been correlated with those from model tests.

  16. Program ispitivanja i metodologija analize spektra vibracija brodske gasne turbine Proteus 52M/558 / The test programme and the methodology of analyzing the vibrations spectrum of a Proteus 52M/558 ship gas turbine

    Predrag S. Dobratić

    2009-10-01

    Full Text Available The paper presents a programme for testing vibrations on a ship gas turbine, based on an analogy of testing and analysis of vibrations on aircraft and/or helicopter gas turbines. A particular attention is given to a choice of vibration parameters and to the analysis of the vibration spectrum as well as to the methods of estimation of criteria of vibration acceptability. The results of the measurement of the vibrations on a Proteus 52M/558 gas turbine installed on a RTOP-405 ship are shown. / U radu je prikazan program ispitivanja vibracija brodske gasne turbine, zasnovan na analogiji ispitivanja i analizi vibracija na avionskim i/ili helikopterskim gasnim turbinama. Posebna pažnja posvećena je izboru parametara vibracija, analizi spektra vibracija, kao i metodama procene kriterijuma prihvatljivosti vibracija. Na kraju rada prikazani su rezultati merenja vibracija na gasnoj turbini Proteus 52M/558 ugrađenoj na brodu RTOP-405.

  17. Crushing Strength of Ship Structures

    Cerup-Simonsen, Bo; Abramowicz, W.; Høstgaard-Brene, C.N.S.

    1999-01-01

    The crushing response of ship structures is of primary importance to the designers and practicing engineers concerned with accidental loading and accident reconstruction of marine vehicles. Ship to-ship collisions, ship-harbor infrastructure interaction or ship-offshore structure interaction are ...

  18. The Couplex test cases: models and lessons

    Bourgeat, A.; Kern, M.; Schumacher, S.; Talandier, J.

    2003-01-01

    The Couplex test cases are a set of numerical test models for nuclear waste deep geological disposal simulation. They are centered around the numerical issues arising in the near and far field transport simulation. They were used in an international contest, and are now becoming a reference in the field. We present the models used in these test cases, and show sample results from the award winning teams. (authors)

  19. Shipping Information Pipeline

    Jensen, Thomas; Vatrapu, Ravi

    2015-01-01

    and national borders within international shipping which is a rather complex domain. The intellectual objective is to generate and evaluate the efficacy and effectiveness of design principles for inter-organizational information infrastructures in the international shipping domain that can have positive...

  20. Liner Shipping Fleet Repositioning

    Tierney, Kevin; Jensen, Rune Møller

    2011-01-01

    Liner shipping fleet repositioning consists of moving vessels between services in a liner ship- ping network in order to better orient the overall network to the world economy, and to ensure the proper maintenance of vessels. Thus, fleet repositioning involves sailing and loading activities subject...

  1. Effective and Safe Ships

    Pedersen, Preben Terndrup; Amdahl, Jørgen; Rutgersson, Olle

    1996-01-01

    A Joint Nordic Research project "Effecive and Safe Ships" is presented. The project is aiming to develop methods and tools for quantitative evaluation fo ship safety. This report is the report of the preliminary phase where the plan for the main project is developed. The objectives of the project...

  2. Tree-Based Global Model Tests for Polytomous Rasch Models

    Komboz, Basil; Strobl, Carolin; Zeileis, Achim

    2018-01-01

    Psychometric measurement models are only valid if measurement invariance holds between test takers of different groups. Global model tests, such as the well-established likelihood ratio (LR) test, are sensitive to violations of measurement invariance, such as differential item functioning and differential step functioning. However, these…

  3. LCA-ship. Design tool for energy efficient ships. A Life Cycle Analysis Program for Ships. Final report

    Jiven, Karl; Sjoebris, Anders [MariTerm AB, Goeteborg (Sweden); Nilsson, Maria [Lund Univ. (Sweden). Stiftelsen TEM; Ellis, Joanne; Traegaardh, Peter; Nordstroem, Malin [SSPA Sweden AB, Goeteborg (Sweden)

    2004-05-01

    processed LCA data in the tool contain the key factors to make it possible to perform life cycle analyses of such a complex 'product' as a ship and the sea transport activity performed by the ship. The calculated environmental impact can also be analysed with respect to different operations, life cycle phases etc. To make comparisons easier between ship concepts etc., the calculated environmental impact can be evaluated with different categorisations and valuation models in an analyses module.

  4. Shipping Information Pipeline

    Jensen, Thomas

    to creating a more efficient shipping industry, and a number of critical issues are identified. These include that shipments depend on shipping information, that shipments often are delayed due to issues with documentation, that EDI messages account for only a minor part of the needed information......This thesis applies theoretical perspectives from the Information Systems (IS) research field to propose how Information Technology (IT) can improve containerized shipping. This question is addressed by developing a set of design principles for an information infrastructure for sharing shipping...... information named the Shipping Information Pipeline (SIP). Review of the literature revealed that IS research prescribed a set of meta-design principles, including digitalization and digital collaboration by implementation of Inter-Organizational Systems based on Electronic Data Interchange (EDI) messages...

  5. A hybrid numerical model system of LCO2 and CO2 enriched seawater dynamics in the ocean induced by moving-ship releasing

    Chen, B.; Song, Y.; Ohsumi, T.; AIST, Ibaraki; Nishio, M.; Akai, M.

    2004-01-01

    A numerical modeling system has been developed, based on an engineering background, of the direct disposal of liquid carbon dioxide into the ocean by a moving-ship, to predict the physico-chemical dynamics of liquid carbon dioxide droplets and carbon dioxide enriched seawater in the ocean. This is a hybrid simulation model system consisting of a three-dimensional small-scale near-field model and a two-dimensional horizontal turbulent dispersion model. The dynamics near to release sites include double-plume creation, interaction, evolution, and coupling with ocean currents; these are described by using two-fluid large-eddy simulation technology. The further development of carbon dioxide enriched seawater, as a passive-inert scalar, in relatively larger spatial and time scales (28x28 km and up to 100 h) is then simulated by a horizontal turbulent dispersion model. For the case of liquid carbon dioxide release at a depth of 2000 m with mass flow rate of 100 kg/s and initial droplet diameter of 8.0 mm, and with ship speed of 3.0 m/s, the model predicts a vertically separated carbon dioxide enriched seawater plume, 330 m in height and 40 m in width at time about 1 h after release with a minimum pH of 6.20 corresponding to carbon dioxide concentration of 0.18 kg/m 3 , in the surrounding area. This carbon dioxide enriched seawater plume diffused turbulently in the horizontal surface to an area of 9.8x10.5 km 2 after 100 h. (author)

  6. Model tests for prestressed concrete pressure vessels

    Stoever, R.

    1975-01-01

    Investigations with models of reactor pressure vessels are used to check results of three dimensional calculation methods and to predict the behaviour of the prototype. Model tests with 1:50 elastic pressure vessel models and with a 1:5 prestressed concrete pressure vessel are described and experimental results are presented. (orig.) [de

  7. Safety analysis report for packaging Lawrence Livermore Laboratories shipping containers

    Evans, J.H.

    1975-12-01

    The Lawrence Livermore Laboratories shipping containers were designed at Oak Ridge National Laboratory for use in transporting weapons and nuclear components. The design for the containers was evaluated to show compliance with applicable regulations governing packages in which radioactive and fissile materials are transported. Computational procedures were used to determine the structural integrity and thermal behavior of the containers relative to the standards for the normal conditions of transport. A full-scale container test model was destructively tested to verify compliance with the standards for the accident conditions. The results of the analytical evaluations and the tests demonstrate that the design for the Lawrence Livermore Laboratories shipping containers is in compliance with the applicable regulations

  8. Model-based testing for embedded systems

    Zander, Justyna; Mosterman, Pieter J

    2011-01-01

    What the experts have to say about Model-Based Testing for Embedded Systems: "This book is exactly what is needed at the exact right time in this fast-growing area. From its beginnings over 10 years ago of deriving tests from UML statecharts, model-based testing has matured into a topic with both breadth and depth. Testing embedded systems is a natural application of MBT, and this book hits the nail exactly on the head. Numerous topics are presented clearly, thoroughly, and concisely in this cutting-edge book. The authors are world-class leading experts in this area and teach us well-used

  9. Nuclear ships and their safety

    NONE

    1961-04-15

    Several aspects of nuclear ship propulsion, with special reference to nuclear safety, were discussed at an international symposium at Taormina, Italy, from 14-18 November 1960. Discussions on specific topics are conducted, grouped under the following headings: Economics and National Activities in Nuclear Ship Propulsion; International Problems and General Aspects of Safety for Nuclear Ships; Nuclear Ship Projects from the Angle of Safety; Ship Reactor Problems; Sea Motion and Hull Problems; Maintenance and Refuelling Problems; and Safety Aspects of Nuclear Ship Operation.

  10. Real-time simulation of response to load variation for a ship reactor based on point-reactor double regions and lumped parameter model

    Wang Qiao; Zhang De [Department of Nuclear Energy Science and Engineering, Naval University of Engineering, Wuhan 430033 (China); Chen Wenzhen, E-mail: Cwz2@21cn.com [Department of Nuclear Energy Science and Engineering, Naval University of Engineering, Wuhan 430033 (China); Chen Zhiyun [Department of Nuclear Energy Science and Engineering, Naval University of Engineering, Wuhan 430033 (China)

    2011-05-15

    Research highlights: > We calculate the variation of main parameters of the reactor core by the Simulink. > The Simulink calculation software (SCS) can deal well with the stiff problem. > The high calculation precision is reached with less time, and the results can be easily displayed. > The quick calculation of ship reactor transient can be achieved by this method. - Abstract: Based on the point-reactor double regions and lumped parameter model, while the nuclear power plant second loop load is increased or decreased quickly, the Simulink calculation software (SCS) is adopted to calculate the variation of main physical and thermal-hydraulic parameters of the reactor core. The calculation results are compared with those of three-dimensional simulation program. It is indicated that the SCS can deal well with the stiff problem of the point-reactor kinetics equations and the coupled problem of neutronics and thermal-hydraulics. The high calculation precision can be reached with less time, and the quick calculation of parameters of response to load disturbance for the ship reactor can be achieved. The clear image of the calculation results can also be displayed quickly by the SCS, which is very significant and important to guarantee the reactor safety operation.

  11. Assessment regarding the use of the computer aided analytical models in the calculus of the general strength of a ship hull

    Hreniuc, V.; Hreniuc, A.; Pescaru, A.

    2017-08-01

    Solving a general strength problem of a ship hull may be done using analytical approaches which are useful to deduce the buoyancy forces distribution, the weighting forces distribution along the hull and the geometrical characteristics of the sections. These data are used to draw the free body diagrams and to compute the stresses. The general strength problems require a large amount of calculi, therefore it is interesting how a computer may be used to solve such problems. Using computer programming an engineer may conceive software instruments based on analytical approaches. However, before developing the computer code the research topic must be thoroughly analysed, in this way being reached a meta-level of understanding of the problem. The following stage is to conceive an appropriate development strategy of the original software instruments useful for the rapid development of computer aided analytical models. The geometrical characteristics of the sections may be computed using a bool algebra that operates with ‘simple’ geometrical shapes. By ‘simple’ we mean that for the according shapes we have direct calculus relations. In the set of ‘simple’ shapes we also have geometrical entities bounded by curves approximated as spline functions or as polygons. To conclude, computer programming offers the necessary support to solve general strength ship hull problems using analytical methods.

  12. Test-driven modeling of embedded systems

    Munck, Allan; Madsen, Jan

    2015-01-01

    To benefit maximally from model-based systems engineering (MBSE) trustworthy high quality models are required. From the software disciplines it is known that test-driven development (TDD) can significantly increase the quality of the products. Using a test-driven approach with MBSE may have...... a similar positive effect on the quality of the system models and the resulting products and may therefore be desirable. To define a test-driven model-based systems engineering (TD-MBSE) approach, we must define this approach for numerous sub disciplines such as modeling of requirements, use cases...... suggest that our method provides a sound foundation for rapid development of high quality system models....

  13. Numerical Ship Hydrodynamics : an assessment of the Gothenburg 2010 Workshop

    Stern, Frederick; Visonneau, Michel

    2014-01-01

    This book assesses the state-of-the-art in computational fluid dynamics (CFD) applied to ship hydrodynamics and provides guidelines for the future developments in the field based on the Gothenburg 2010 Workshop. It presents ship hull test cases, experimental data and submitted computational methods, conditions, grids and results.  Analysis is made of errors for global (resistance, sinkage and trim and self-propulsion) and local flow (wave elevations and mean velocities and turbulence) variables, including standard deviations for global variables and propeller modeling for self-propulsion. The effects of grid size and turbulence models are evaluated for both global and local flow variables. Detailed analysis is made of turbulence modeling capabilities for capturing local flow physics. Errors are also analyzed for head-wave seakeeping and forward speed diffraction, and calm-water forward speed-roll decay. Resistance submissions are used to evaluate the error and uncertainty by means of a systematic verificatio...

  14. Superconducting solenoid model magnet test results

    Carcagno, R.; Dimarco, J.; Feher, S.; Ginsburg, C.M.; Hess, C.; Kashikhin, V.V.; Orris, D.F.; Pischalnikov, Y.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; /Fermilab

    2006-08-01

    Superconducting solenoid magnets suitable for the room temperature front end of the Fermilab High Intensity Neutrino Source (formerly known as Proton Driver), an 8 GeV superconducting H- linac, have been designed and fabricated at Fermilab, and tested in the Fermilab Magnet Test Facility. We report here results of studies on the first model magnets in this program, including the mechanical properties during fabrication and testing in liquid helium at 4.2 K, quench performance, and magnetic field measurements. We also describe new test facility systems and instrumentation that have been developed to accomplish these tests.

  15. Superconducting solenoid model magnet test results

    Carcagno, R.; Dimarco, J.; Feher, S.; Ginsburg, C.M.; Hess, C.; Kashikhin, V.V.; Orris, D.F.; Pischalnikov, Y.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; Tompkins, J.C.; Wokas, T.; Fermilab

    2006-01-01

    Superconducting solenoid magnets suitable for the room temperature front end of the Fermilab High Intensity Neutrino Source (formerly known as Proton Driver), an 8 GeV superconducting H- linac, have been designed and fabricated at Fermilab, and tested in the Fermilab Magnet Test Facility. We report here results of studies on the first model magnets in this program, including the mechanical properties during fabrication and testing in liquid helium at 4.2 K, quench performance, and magnetic field measurements. We also describe new test facility systems and instrumentation that have been developed to accomplish these tests

  16. Space Launch System Scale Model Acoustic Test Ignition Overpressure Testing

    Nance, Donald; Liever, Peter; Nielsen, Tanner

    2015-01-01

    The overpressure phenomenon is a transient fluid dynamic event occurring during rocket propulsion system ignition. This phenomenon results from fluid compression of the accelerating plume gas, subsequent rarefaction, and subsequent propagation from the exhaust trench and duct holes. The high-amplitude unsteady fluid-dynamic perturbations can adversely affect the vehicle and surrounding structure. Commonly known as ignition overpressure (IOP), this is an important design-to environment for the Space Launch System (SLS) that NASA is currently developing. Subscale testing is useful in validating and verifying the IOP environment. This was one of the objectives of the Scale Model Acoustic Test, conducted at Marshall Space Flight Center. The test data quantifies the effectiveness of the SLS IOP suppression system and improves the analytical models used to predict the SLS IOP environments. The reduction and analysis of the data gathered during the SMAT IOP test series requires identification and characterization of multiple dynamic events and scaling of the event waveforms to provide the most accurate comparisons to determine the effectiveness of the IOP suppression systems. The identification and characterization of the overpressure events, the waveform scaling, the computation of the IOP suppression system knockdown factors, and preliminary comparisons to the analytical models are discussed.

  17. Space Launch System Scale Model Acoustic Test Ignition Overpressure Testing

    Nance, Donald K.; Liever, Peter A.

    2015-01-01

    The overpressure phenomenon is a transient fluid dynamic event occurring during rocket propulsion system ignition. This phenomenon results from fluid compression of the accelerating plume gas, subsequent rarefaction, and subsequent propagation from the exhaust trench and duct holes. The high-amplitude unsteady fluid-dynamic perturbations can adversely affect the vehicle and surrounding structure. Commonly known as ignition overpressure (IOP), this is an important design-to environment for the Space Launch System (SLS) that NASA is currently developing. Subscale testing is useful in validating and verifying the IOP environment. This was one of the objectives of the Scale Model Acoustic Test (SMAT), conducted at Marshall Space Flight Center (MSFC). The test data quantifies the effectiveness of the SLS IOP suppression system and improves the analytical models used to predict the SLS IOP environments. The reduction and analysis of the data gathered during the SMAT IOP test series requires identification and characterization of multiple dynamic events and scaling of the event waveforms to provide the most accurate comparisons to determine the effectiveness of the IOP suppression systems. The identification and characterization of the overpressure events, the waveform scaling, the computation of the IOP suppression system knockdown factors, and preliminary comparisons to the analytical models are discussed.

  18. Hydrodynamics of Ship Propellers

    Breslin, John P.; Andersen, Poul

    This book deals with flows over propellers operating behind ships, and the hydrodynamic forces and moments which the propeller generates on the shaft and on the ship hull.The first part of the text is devoted to fundamentals of the flow about hydrofoil sections (with and without cavitation...... of an intermittently cavitating propeller in a wake and the pressures and forces it exerts on the shaft and on the ship hull is examined. A final chapter discusses the optimization of efficiency of compound propulsors. The authors have taken care to clearly describe physical concepts and mathematical steps. Appendices...

  19. Do Test Design and Uses Influence Test Preparation? Testing a Model of Washback with Structural Equation Modeling

    Xie, Qin; Andrews, Stephen

    2013-01-01

    This study introduces Expectancy-value motivation theory to explain the paths of influences from perceptions of test design and uses to test preparation as a special case of washback on learning. Based on this theory, two conceptual models were proposed and tested via Structural Equation Modeling. Data collection involved over 870 test takers of…

  20. Sample Size Determination for Rasch Model Tests

    Draxler, Clemens

    2010-01-01

    This paper is concerned with supplementing statistical tests for the Rasch model so that additionally to the probability of the error of the first kind (Type I probability) the probability of the error of the second kind (Type II probability) can be controlled at a predetermined level by basing the test on the appropriate number of observations.…

  1. Is the standard model really tested?

    Takasugi, E.

    1989-01-01

    It is discussed how the standard model is really tested. Among various tests, I concentrate on the CP violation phenomena in K and B meson system. Especially, the resent hope to overcome the theoretical uncertainty in the evaluation on the CP violation of K meson system is discussed. (author)

  2. Wind Loads on Ships and Offshore Structures Estimated by CFD

    Aage, Christian; Hvid, S.L.; Hughes, P.H.

    1997-01-01

    Wind loads on ships and offshore structures could until recently be determined only by model tests, or by statistical methods based on model tests. By the development of Computational Fluid Dynamics or CFD there is now a realistic computational alternative available. In this paper, wind loads...... on a seagoing ferry and on a semisubmersible offshore platform have been estimated by CFD. The results have been compared with wind tunnel model tests and, for the ferry, a few full-scale measurements, and good agreement is obtained. The CFD method offers the possibility of a computational estimate of scale...... effects related to wind tunnel model testing. An example of such an estimate on the ferry is discussed. Due to the time involved in generating the computational mesh and in computing the solution, the CFD method is not at the moment economically competitive to routine wind tunnel model testing....

  3. Ship-to-Ship Radiocommunication Trial by Using Wireless LAN

    Yasuyuki Niwa

    2015-12-01

    In a former field radiocommunication trial, omni-directional antennas were used and a few hundred kbps throughput between two ships was measured, which was not enough for our research target (over 1Mbps. In order to get faster throughput, a field radiocommunication trial was carried out again with a few types of directional antennas and RSSI (Received Signal Strength Indication and the throughput between two ships was measured simultaneously. As a result, multi-path (2-path model affected by the reflection of the sea surface was confirmed and also the characteristics of the directional antennas such as half-power angle were confirmed, but the measured throughput was fast enough to meet our expectation.

  4. Designing Adaptable Ships: Modularity and Flexibility in Future Ship Designs

    2016-01-01

    with motors, belts, shafts , seals, valves, hose spindles , and switches. If ship installation is not installed, the system will be status quo. Ship...Impact: the current centrifugal purifiers (Alfa-Laval) have experienced frequent failures with motor, belts, shafts , seals, valves, hose spindles ... Designing Adaptable Ships Modularity and Flexibility in Future Ship Designs John F. Schank, Scott Savitz, Ken Munson, Brian Perkinson, James

  5. Mining of Ship Operation Data for Energy Conservation

    Petersen, Jóan Petur

    model is introduces through a study of the wellknown sunspot time series, and then on ship data. The dynamical modelling approach is investigated using both the Artificial Neural Network and the Gaussian mixture model. The thesis also presentes a novel and publicly available data set of high quality...... sensory data on which all the models are based and tested. No other similar publicly available data set exists. The data presented is a publicly available full-scale data set, with a whole range of features sampled over a period of 2 months. The data is online with an accompanying homepage, where all...

  6. Modelling and Testing of Friction in Forging

    Bay, Niels

    2007-01-01

    Knowledge about friction is still limited in forging. The theoretical models applied presently for process analysis are not satisfactory compared to the advanced and detailed studies possible to carry out by plastic FEM analyses and more refined models have to be based on experimental testing...

  7. Analysis of Ship Groundings on Soft Sea Beds

    Simonsen, Bo Cerup; Pedersen, Preben Terndrup

    1997-01-01

    it influences the ship heave and pitch motions as well as the friction between the ship and the soil.In this paper a rational calculation model is presented for the sea bed soil reaction forces on the ship bottom. The model is based on the assumption that the penetration of the ship bow generates a flow of pore......The consequences associated with ships running aground depend very much on the soil characteristics of the sea bed and the geometrical shape of the ship bow. The penetration into the sea bed depends on these factors and the penetration is an important factor for the ship motion because...... by the theory of frictional soils in rupture. Frictional stresses on the bow surface are assumed to be related to the normal pressure by a simple Coulumb relation. The total soil reaction as a function of velocity and penetration is found by integration of normal pressure and frictional stresses over...

  8. Civilian nuclear ships

    Oelgaard, P.L.

    1993-03-01

    This report contains a review of the information available on nuclear powered ships, built for civilian purposes. In the introduction a short discussion is given of the reasons for the limited use of nuclear ships for these purposes. In the second section a brief review is presented of data for the three experimental/merchant ships build by the United States, Germany and Japan, i.e. NS Savannah, NS Otto Hahn and NS Mutsu. In the third section the Soviet/Russian icebreaker NS Lenin is considered. Its design, operational experience and the introduction of a new nuclear propulsion plant is reviewed. In the fourth section the newer Soviet/Russian icebreakers with nuclear propulsion are considered. Finally design of the Soviet/Russian icebreaker transport/container ship NS Sevmorput is reviewed in the fifth section. The future Russian plans for nuclear vessels for the arctic waters are briefly discussed. (au)

  9. Ship propulsion reactors technology

    Fribourg, Ch.

    2002-01-01

    This paper takes the state of the art on ship propulsion reactors technology. The french research programs with the corresponding technological stakes, the reactors specifications and advantages are detailed. (A.L.B.)

  10. Ship construction and welding

    Mandal, Nisith R

    2017-01-01

    This book addresses various aspects of ship construction, from ship types and construction materials, to welding technologies and accuracy control. The contents of the book are logically organized and divided into twenty-one chapters. The book covers structural arrangement with longitudinal and transverse framing systems based on the service load, and explains basic structural elements like hatch side girders, hatch end beams, stringers, etc. along with structural subassemblies like floors, bulkheads, inner bottom, decks and shells. It presents in detail double bottom construction, wing tanks & duct keels, fore & aft end structures, etc., together with necessary illustrations. The midship sections of various ship types are introduced, together with structural continuity and alignment in ship structures. With regard to construction materials, the book discusses steel, aluminum alloys and fiber reinforced composites. Various methods of steel material preparation are discussed, and plate cutting and form...

  11. Nuclear ship accidents

    Oelgaard, P.L.

    1993-05-01

    In this report available information on 28 nuclear ship accident and incidents is considered. Of these 5 deals with U.S. ships and 23 with USSR ships. The ships are in almost all cases nuclear submarines. Only events that involve the nuclear propulsion plants, radiation exposures, fires/explosions and sea water leaks into the submarines are considered. Comments are made on each of the events, and at the end of the report an attempt is made to point out the weaknesses of the submarine designs which have resulted in the accidents. It is emphasized that much of the available information is of a rather dubious nature. consequently some of the assessments made may not be correct. (au)

  12. Applicant's guide related to requests of shipping approval and of acceptance of parcel models or radioactive products aimed at civilian use transported on public road - Guide nr 7 - Index 0, release of the 07/04/2009

    2009-01-01

    This guide presents the recommendations made by the ASN to applicants in order to facilitate approval requests and shipping approvals related to the transportation of radioactive products. After a recall of the legal context, these recommendations address the documents to be provided in support of an approval request or of a shipping approval, the content of the safety file, the instruction delay, the approval certificate, and changes brought to the parcel model. Appendices contain issues raised by expertise based on experiences, the European PDSR (Package Design Safety Report), and a model for the elaboration of a certificate project

  13. SHIPPING REQUESTS ON EDH

    Logistics Group

    2001-01-01

    Users are informed that as from 1 September 2001 all Shipping Requests must be made on EDH using the appropriate electronic form. The submission of user requests directly into EDH will help rationalise the activities of the Shipping Service (Import & Export), with requests being automatically forwarded to hierarchical supervisors thereby improving the processing speed and facilitating the follow-up. Thank you for your collaboration.

  14. Plastic Pollution from Ships

    Čulin, Jelena; Bielić, Toni

    2016-01-01

    The environmental impact of shipping on marine environment includes discharge of garbage. Plastic litter is of particular concern due to abundance, resistance to degradation and detrimental effect on marine biota. According to recently published studies, a further research is required to assess human health risk. Monitoring data indicate that despite banning plastic disposal at sea, shipping is still a source of plastic pollution. Some of the measures to combat the problem are discussed.

  15. On the Global Ship Hull Bending Energy in Ship Collisions

    Pedersen, Preben Terndrup; Li, Y.

    2004-01-01

    During ship collisions part of the kinetic energy of the involved vessels prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can be stored in elastic...... hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non trivial part of the energy released for structural deformation during the collision can be absorbed as elastic energy in global...... ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship-ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing is confined...

  16. Development of the Nuclear Ship Database. 1. Outline of the Nuclear Ship Experimental Database

    Kyouya, Masahiko; Ochiai, Masa-aki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Hashidate, Kouji

    1995-03-01

    We obtained the experimental data on the effects of the ship motions and the change in load and caused by the ship operations, the waves, the winds etc., to the nuclear power plant behavior, through the Power-up Tests and Experimental Voyages of the Nuclear Ship MUTSU. Moreover, we accumulated the techniques, the knowledge and others on the Nuclear Ship development at the each stage of the N.S. MUTSU Research and Development program, such as the design stage, the construction stage, the operation stage and others. These data, techniques, knowledge and others are the assembly of the experimental data and the experiences through the design, the construction and the operation of the first nuclear ship in JAPAN. It is important to keep and pigeonhole these products of the N.S. MUTSU program in order to utilize them effectively in the research and development of the advanced marine reactor, since there is no construction plan of the nuclear ship for the present in JAPAN. We have been carrying out the development of the Nuclear Ship Database System since 1991 for the purpose of effective utilization of the N.S. MUTSU products in the design study of the advanced marine reactors. The part of the Nuclear Ship Database System on the experimental data, called Nuclear Ship Experimental Database, was already accomplished and utilized since 1993. This report describes the outline and the use of the Nuclear Ship Experimental Database.The remaining part of the database system on the documentary data, called Nuclear Ship Documentary Database, are now under development. (author).

  17. Development of the Nuclear Ship Database. 1. Outline of the Nuclear Ship Experimental Database

    Kyouya, Masahiko; Ochiai, Masa-aki; Hashidate, Kouji.

    1995-03-01

    We obtained the experimental data on the effects of the ship motions and the change in load and caused by the ship operations, the waves, the winds etc., to the nuclear power plant behavior, through the Power-up Tests and Experimental Voyages of the Nuclear Ship MUTSU. Moreover, we accumulated the techniques, the knowledge and others on the Nuclear Ship development at the each stage of the N.S. MUTSU Research and Development program, such as the design stage, the construction stage, the operation stage and others. These data, techniques, knowledge and others are the assembly of the experimental data and the experiences through the design, the construction and the operation of the first nuclear ship in JAPAN. It is important to keep and pigeonhole these products of the N.S. MUTSU program in order to utilize them effectively in the research and development of the advanced marine reactor, since there is no construction plan of the nuclear ship for the present in JAPAN. We have been carrying out the development of the Nuclear Ship Database System since 1991 for the purpose of effective utilization of the N.S. MUTSU products in the design study of the advanced marine reactors. The part of the Nuclear Ship Database System on the experimental data, called Nuclear Ship Experimental Database, was already accomplished and utilized since 1993. This report describes the outline and the use of the Nuclear Ship Experimental Database.The remaining part of the database system on the documentary data, called Nuclear Ship Documentary Database, are now under development. (author)

  18. Competitive Liner Shipping Network Design

    Karsten, Christian Vad

    .The contributions of this thesis cover modeling, methodology, and applications.The developed methods address operational (cargo routing), tactical (speed optimization and service selection), and strategic (network design) planning problems faced by liner shipping companies. Ultimately, the proposed methods help...... take the container transportation times that can be realized in the network nor the number of transshipments into consideration. This is mainly because the optimization problem is based on other transportation networks where these constraints are not decisive to the quality of the network. Furthermore......, the problem in itself is challenging to optimize due to its size and complexity. However, the field has seen crucial progress and is mature to include handling of competitiveness in the actual design of the network.As a liner shipping network is an organic entity, which is constantly changed to reflect...

  19. An assessment of simplified methods to determine damage from ship-to-ship collisions

    Parks, M.B.; Ammerman, D.J.

    1996-01-01

    Sandia National Laboratories (SNL) is studying the safety of shipping, radioactive materials (RAM) by sea, the SeaRAM project (McConnell, et al. 1995), which is sponsored by the US Department of Energy (DOE). The project is concerned with the potential effects of ship collisions and fires on onboard RAM packages. Existing methodologies are being assessed to determine their adequacy to predict the effect of ship collisions and fires on RAM packages and to estimate whether or not a given accident might lead to a release of radioactivity. The eventual goal is to develop a set of validated methods, which have been checked by comparison with test data and/or detailed finite element analyses, for predicting the consequences of ship collisions and fires. These methods could then be used to provide input for overall risk assessments of RAM sea transport. The emphasis of this paper is on methods for predicting- effects of ship collisions

  20. Outer Dynamics of Ship Collisions

    Pedersen, Preben Terndrup

    1996-01-01

    The purpose is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisions with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding structures....

  1. Recent situations around nuclear ships

    Mizuno, Hiroshi

    1978-01-01

    The philosophy when the safety standard for nuclear ships is drawn up and the international rules specifically for nuclear ships are summarized. As for the safety standard for nuclear ships, the safety requirements for ordinary ships, for the ships transporting nuclear reactors, for ordinary nuclear reactors, and for the reactors moving around the seas must be included. As for the international rules for nuclear ships, there are chapter 8 ''Nuclear ships'' in the International Convention on the Safety of Life at Sea, 1960 and 1974, and Safety Consideration in the Use of Ports and Approaches by Nuclear Merchant Ships. Also there are national rules and standards in Japan and foreign countries. One of the means to explore the practicality of nuclear ships is the investigation of the economy. At this time, the social merits and demerits of nuclear ships must be compared with conventional ships by taking total expenses into account without omission. When oil is depleted, the age of nuclear ships will not necessarily begin, and the will be still some competitors. The investigations concerning the economy of nuclear ships have been carried out in various countries. The present state of the development of nuclear ships in Japan and foreign countries is explained. Many conferences and symposia have been held concerning nuclear ships, and those held recently are enumerated. The realization of nuclear ship age cannot be anticipated from existing papers and shipbuilding projects. (Kako, I.)

  2. Outer Dynamics of Ship Collisions

    Pedersen, Preben Terndrup

    1996-01-01

    The purpose of these notes is to present analysis procedures for the motion of ships during ship-ship collisions and for ship collisons with offshore structures. The aim is to estimate that part of the lost kinetic energy which will have to be absorbed by rupture and plastic damage of the colliding...

  3. Requirement of a Ship Breaking Yard at the Arvand Free Zone Area

    Homayoun Yousefi

    2016-09-01

    Full Text Available In this paper, the author is going to investigate the concept of ship recycling which implies to the materials and equipment including end of ships life. The scraped steel is melted down and is commonly used in the construction industries of ship recycling countries, and some equipment might be re-used in other industries too. A segment of this paper is dedicated to describe about the strategic position of Arvand River and the location of Arvand Free Zone area at the Persian Gulf. It should be noted that ship recycling commonly takes place in developing countries which tend to have a competitive advantage due to the low cost labor, may have weaker environmental protection / worker health and safety regulations, and have national demand for the outputs of the activity. The International Maritime Organization (IMO adopted the Hong Kong International Convention related to the safety and environmental sound recycling of ships to address the growing about the environment, job health and safety risks related to ship recycling. A part of this paper dedicated to review the role of the Hong Kong Convention in order to ensure the process of ship recycling without risks to human health and to the environment. The main part of this paper is designated to evaluate the role of establishment of a ship scraping yard at the Arvand Free Zone Area, its market at the Persian Gulf and improving the safety of navigation at the Arvand River. The research methodology of this paper will be designated to consider the qualitative part of this research by using interview with the experts in order to find out and select the key factors for further consideration; as a result of that a model will be created which can be tested by a questioner. In addition to the above explanation, relationship between the variables and testing hypothesizes of this research will be analyzed by using SPSS and Lisrel software as quantitative part of this research.

  4. Neutrino physics with SHIP

    van Herwijnen, Eric

    2016-01-01

    SHIP is a new general purpose fixed target facility, whose Technical Proposal has been recently reviewed by the CERN SPS Committee. It recommended that the experiment proceed further to a Comprehensive Design phase. In its initial phase, the 400 GeV proton beam extracted from the SPS will be dumped on a heavy target with the aim of integrating 2×1020 POT (Protons On Target) in 5 years. A dedicated detector, based on a long vacuum tank followed by a spectrometer and particle identification detectors, will allow probing a variety of models with light long-lived exotic particles and masses below O(10) GeV/c 2 . The main focus will be the physics of the so-called Hidden Portals. The sensitivity to Heavy Neutrinos will allow to probe for the first time the mass range between the kaon and the charm meson mass, and a range of couplings for which Baryogenesis and active neutrino masses could also be explained. Another dedicated detector will allow the study of neutrino cross-sections and angular distributions. ντ ...

  5. Kinematic tests of exotic flat cosmological models

    Charlton, J.C.; Turner, M.S.; NASA/Fermilab Astrophysics Center, Batavia, IL)

    1987-01-01

    Theoretical prejudice and inflationary models of the very early universe strongly favor the flat, Einstein-de Sitter model of the universe. At present the observational data conflict with this prejudice. This conflict can be resolved by considering flat models of the universe which posses a smooth component of energy density. The kinematics of such models, where the smooth component is relativistic particles, a cosmological term, a network of light strings, or fast-moving, light strings is studied in detail. The observational tests which can be used to discriminate between these models are also discussed. These tests include the magnitude-redshift, lookback time-redshift, angular size-redshift, and comoving volume-redshift diagrams and the growth of density fluctuations. 58 references

  6. Kinematic tests of exotic flat cosmological models

    Charlton, J.C.; Turner, M.S.

    1986-05-01

    Theoretical prejudice and inflationary models of the very early Universe strongly favor the flat, Einstein-deSitter model of the Universe. At present the observational data conflict with this prejudice. This conflict can be resolved by considering flat models of the Universe which possess a smooth component by energy density. We study in detail the kinematics of such models, where the smooth component is relativistic particles, a cosmological term, a network of light strings, or fast-moving, light strings. We also discuss the observational tests which can be used to discriminate between these models. These tests include the magnitude-redshift, lookback time-redshift, angular size-redshift, and comoving volume-redshift diagrams and the growth of density fluctuations

  7. Kinematic tests of exotic flat cosmological models

    Charlton, J.C.; Turner, M.S.

    1986-05-01

    Theoretical prejudice and inflationary models of the very early Universe strongly favor the flat, Einstein-deSitter model of the Universe. At present the observational data conflict with this prejudice. This conflict can be resolved by considering flat models of the Universe which possess a smooth component by energy density. We study in detail the kinematics of such models, where the smooth component is relativistic particles, a cosmological term, a network of light strings, or fast-moving, light strings. We also discuss the observational tests which can be used to discriminate between these models. These tests include the magnitude-redshift, lookback time-redshift, angular size-redshift, and comoving volume-redshift diagrams and the growth of density fluctuations.

  8. Observation-Based Modeling for Model-Based Testing

    Kanstrén, T.; Piel, E.; Gross, H.G.

    2009-01-01

    One of the single most important reasons that modeling and modelbased testing are not yet common practice in industry is the perceived difficulty of making the models up to the level of detail and quality required for their automated processing. Models unleash their full potential only through

  9. A 'Turing' Test for Landscape Evolution Models

    Parsons, A. J.; Wise, S. M.; Wainwright, J.; Swift, D. A.

    2008-12-01

    Resolving the interactions among tectonics, climate and surface processes at long timescales has benefited from the development of computer models of landscape evolution. However, testing these Landscape Evolution Models (LEMs) has been piecemeal and partial. We argue that a more systematic approach is required. What is needed is a test that will establish how 'realistic' an LEM is and thus the extent to which its predictions may be trusted. We propose a test based upon the Turing Test of artificial intelligence as a way forward. In 1950 Alan Turing posed the question of whether a machine could think. Rather than attempt to address the question directly he proposed a test in which an interrogator asked questions of a person and a machine, with no means of telling which was which. If the machine's answer could not be distinguished from those of the human, the machine could be said to demonstrate artificial intelligence. By analogy, if an LEM cannot be distinguished from a real landscape it can be deemed to be realistic. The Turing test of intelligence is a test of the way in which a computer behaves. The analogy in the case of an LEM is that it should show realistic behaviour in terms of form and process, both at a given moment in time (punctual) and in the way both form and process evolve over time (dynamic). For some of these behaviours, tests already exist. For example there are numerous morphometric tests of punctual form and measurements of punctual process. The test discussed in this paper provides new ways of assessing dynamic behaviour of an LEM over realistically long timescales. However challenges remain in developing an appropriate suite of challenging tests, in applying these tests to current LEMs and in developing LEMs that pass them.

  10. Conclusions from collision examinations for nuclear merchant ships in the FRG

    Woisin, G.

    1978-01-01

    In Germany model tests have been performed for the utilization of a resisting type barrier instead of an energy absorbing type barrier, the latter used in nuclear merchant ships up to now only. After reviewing the model technique the results of nine tests with the new barrier are discussed. Calculations performed to the newly raised questions of the shock accelerations of the reactor plant and of possible overstressing of the hull are reported. The new design has many advantages with respect to safety and to the arrangement of a reactor plant in a ship too. Some questions partly remain unanswered at the moment concerning oblique collisions to the ends of the barrier and the possible effects of bulk cargo in holds close to the bow in striking ships of smaller size

  11. Effect of Water Flows on Ship Traffic in Narrow Water Channels Based on Cellular Automata

    Hu Hongtao

    2017-11-01

    Full Text Available In narrow water channels, ship traffic may be affected by water flows and ship interactions. Studying their effects can help maritime authorities to establish appropriate management strategies. In this study, a two-lane cellular automation model is proposed. Further, the behavior of ship traffic is analyzed by setting different water flow velocities and considering ship interactions. Numerical experiment results show that the ship traffic density-flux relation is significantly different from the results obtained by classical models. Furthermore, due to ship interactions, the ship lane-change rate is influenced by the water flow to a certain degree.

  12. Engineering Abstractions in Model Checking and Testing

    Achenbach, Michael; Ostermann, Klaus

    2009-01-01

    Abstractions are used in model checking to tackle problems like state space explosion or modeling of IO. The application of these abstractions in real software development processes, however, lacks engineering support. This is one reason why model checking is not widely used in practice yet...... and testing is still state of the art in falsification. We show how user-defined abstractions can be integrated into a Java PathFinder setting with tools like AspectJ or Javassist and discuss implications of remaining weaknesses of these tools. We believe that a principled engineering approach to designing...... and implementing abstractions will improve the applicability of model checking in practice....

  13. Accidents in nuclear ships

    Oelgaard, P L [Risoe National Lab., Roskilde (Denmark); [Technical Univ. of Denmark, Lyngby (Denmark)

    1996-12-01

    This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10{sup -3} per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au).

  14. Accidents in nuclear ships

    Oelgaard, P.L.

    1996-12-01

    This report starts with a discussion of the types of nuclear vessels accidents, in particular accidents which involve the nuclear propulsion systems. Next available information on 61 reported nuclear ship events in considered. Of these 6 deals with U.S. ships, 54 with USSR ships and 1 with a French ship. The ships are in almost all cases nuclear submarines. Only events that involve the sinking of vessels, the nuclear propulsion plants, radiation exposures, fires/explosions, sea-water leaks into the submarines and sinking of vessels are considered. For each event a summary of available information is presented, and comments are added. In some cases the available information is not credible, and these events are neglected. This reduces the number of events to 5 U.S. events, 35 USSR/Russian events and 1 French event. A comparison is made between the reported Soviet accidents and information available on dumped and damaged Soviet naval reactors. It seems possible to obtain good correlation between the two types of events. An analysis is made of the accident and estimates are made of the accident probabilities which are found to be of the order of 10 -3 per ship reactor years. It if finally pointed out that the consequences of nuclear ship accidents are fairly local and does in no way not approach the magnitude of the Chernobyl accident. It is emphasized that some of the information on which this report is based, may not be correct. Consequently some of the results of the assessments made may not be correct. (au)

  15. Pile Model Tests Using Strain Gauge Technology

    Krasiński, Adam; Kusio, Tomasz

    2015-09-01

    Ordinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine the total bearing capacity of the pile, without the knowledge of its distribution into the shaft and base resistances. Much more information can be obtained by carrying out a test of instrumented pile equipped with a system for measuring the distribution of axial force along its core. In the case of pile model tests the use of such measurement is difficult due to small scale of the model. To find a suitable solution for axial force measurement, which could be applied to small scale model piles, we had to take into account the following requirements: - a linear and stable relationship between measured and physical values, - the force measurement accuracy of about 0.1 kN, - the range of measured forces up to 30 kN, - resistance of measuring gauges against aggressive counteraction of concrete mortar and against moisture, - insensitivity to pile bending, - economical factor. These requirements can be fulfilled by strain gauge sensors if an appropriate methodology is used for test preparation (Hoffmann [1]). In this paper, we focus on some aspects of the application of strain gauge sensors for model pile tests. The efficiency of the method is proved on the examples of static load tests carried out on SDP model piles acting as single piles and in a group.

  16. Accuracy tests of the tessellated SLBM model

    Ramirez, A L; Myers, S C

    2007-01-01

    We have compared the Seismic Location Base Model (SLBM) tessellated model (version 2.0 Beta, posted July 3, 2007) with the GNEMRE Unified Model. The comparison is done on a layer/depth-by-layer/depth and layer/velocity-by-layer/velocity comparison. The SLBM earth model is defined on a tessellation that spans the globe at a constant resolution of about 1 degree (Ballard, 2007). For the tests, we used the earth model in file ''unified( ) iasp.grid''. This model contains the top 8 layers of the Unified Model (UM) embedded in a global IASP91 grid. Our test queried the same set of nodes included in the UM model file. To query the model stored in memory, we used some of the functionality built into the SLBMInterface object. We used the method get InterpolatedPoint() to return desired values for each layer at user-specified points. The values returned include: depth to the top of each layer, layer velocity, layer thickness and (for the upper-mantle layer) velocity gradient. The SLBM earth model has an extra middle crust layer whose values are used when Pg/Lg phases are being calculated. This extra layer was not accessed by our tests. Figures 1 to 8 compare the layer depths, P velocities and P gradients in the UM and SLBM models. The figures show results for the three sediment layers, three crustal layers and the upper mantle layer defined in the UM model. Each layer in the models (sediment1, sediment2, sediment3, upper crust, middle crust, lower crust and upper mantle) is shown on a separate figure. The upper mantle P velocity and gradient distribution are shown on Figures 7 and 8. The left and center images in the top row of each figure is the rendering of depth to the top of the specified layer for the UM and SLBM models. When a layer has zero thickness, its depth is the same as that of the layer above. The right image in the top row is the difference between in layer depth for the UM and SLBM renderings. The left and center images in the bottom row of the figures are

  17. Game Strategies of Ship in the Collision Situations

    Jozef Lisowski

    2014-03-01

    Full Text Available The paper introduced the basic model of process of safe ship control in a collision situation using a game model with j objects, which includes non-linear state equations and non-linear, time varying constraints of the state variables as well as the quality game control index in the forms of the game integral payment and the final payment. Approximated model of the process control as the model of multi-step matrix game in the form of dual linear programming problem has been adopted here. The Game Ship Control GSC computer program has been designed in the Matlab/Simulink software in order to determine the own ship's safe trajectory. These considerations have been illustrated with examples of a computer simulation using an GSC program for determining the safe ship's trajectory in real navigational situation. Simulation research were passed for five sets of strategies of the own ship and met ships.

  18. Unit testing, model validation, and biological simulation.

    Sarma, Gopal P; Jacobs, Travis W; Watts, Mark D; Ghayoomie, S Vahid; Larson, Stephen D; Gerkin, Richard C

    2016-01-01

    The growth of the software industry has gone hand in hand with the development of tools and cultural practices for ensuring the reliability of complex pieces of software. These tools and practices are now acknowledged to be essential to the management of modern software. As computational models and methods have become increasingly common in the biological sciences, it is important to examine how these practices can accelerate biological software development and improve research quality. In this article, we give a focused case study of our experience with the practices of unit testing and test-driven development in OpenWorm, an open-science project aimed at modeling Caenorhabditis elegans. We identify and discuss the challenges of incorporating test-driven development into a heterogeneous, data-driven project, as well as the role of model validation tests, a category of tests unique to software which expresses scientific models.

  19. Variable amplitude fatigue, modelling and testing

    Svensson, Thomas.

    1993-01-01

    Problems related to metal fatigue modelling and testing are here treated in four different papers. In the first paper different views of the subject are summarised in a literature survey. In the second paper a new model for fatigue life is investigated. Experimental results are established which are promising for further development of the mode. In the third paper a method is presented that generates a stochastic process, suitable to fatigue testing. The process is designed in order to resemble certain fatigue related features in service life processes. In the fourth paper fatigue problems in transport vibrations are treated

  20. Design, modeling and testing of data converters

    Kiaei, Sayfe; Xu, Fang

    2014-01-01

    This book presents the a scientific discussion of the state-of-the-art techniques and designs for modeling, testing and for the performance analysis of data converters. The focus is put on sustainable data conversion. Sustainability has become a public issue that industries and users can not ignore. Devising environmentally friendly solutions for data conversion designing, modeling and testing is nowadays a requirement that researchers and practitioners must consider in their activities. This book presents the outcome of the IWADC workshop 2011, held in Orvieto, Italy.

  1. Flight Test Maneuvers for Efficient Aerodynamic Modeling

    Morelli, Eugene A.

    2011-01-01

    Novel flight test maneuvers for efficient aerodynamic modeling were developed and demonstrated in flight. Orthogonal optimized multi-sine inputs were applied to aircraft control surfaces to excite aircraft dynamic response in all six degrees of freedom simultaneously while keeping the aircraft close to chosen reference flight conditions. Each maneuver was designed for a specific modeling task that cannot be adequately or efficiently accomplished using conventional flight test maneuvers. All of the new maneuvers were first described and explained, then demonstrated on a subscale jet transport aircraft in flight. Real-time and post-flight modeling results obtained using equation-error parameter estimation in the frequency domain were used to show the effectiveness and efficiency of the new maneuvers, as well as the quality of the aerodynamic models that can be identified from the resultant flight data.

  2. On the global ship hull bending energy in ship collisions

    Pedersen, Preben Terndrup; Li, Yujie

    2009-01-01

    During ship collisions part of the kinetic energy of the involved vessels immediately prior to contact is absorbed as energy dissipated by crushing of the hull structures, by friction and by elastic energy. The purpose of this report is to present an estimate of the elastic energy that can...... be stored in elastic hull vibrations during a ship collision. When a ship side is strengthened in order to improve the crashworthiness it has been argued in the scientific literature that a non-trivial part of the energy released for structural deformation during the collision can be absorbed as elastic...... energy in global ship hull vibrations, such that with strong ship sides less energy has to be spent in crushing of the striking ship bow and/or the struck ship side. In normal ship–ship collision analyses both the striking and struck ship are usually considered as rigid bodies where structural crushing...

  3. Modeling and Testing Legacy Data Consistency Requirements

    Nytun, J. P.; Jensen, Christian Søndergaard

    2003-01-01

    An increasing number of data sources are available on the Internet, many of which offer semantically overlapping data, but based on different schemas, or models. While it is often of interest to integrate such data sources, the lack of consistency among them makes this integration difficult....... This paper addresses the need for new techniques that enable the modeling and consistency checking for legacy data sources. Specifically, the paper contributes to the development of a framework that enables consistency testing of data coming from different types of data sources. The vehicle is UML and its...... accompanying XMI. The paper presents techniques for modeling consistency requirements using OCL and other UML modeling elements: it studies how models that describe the required consistencies among instances of legacy models can be designed in standard UML tools that support XMI. The paper also considers...

  4. Ice and AIS: ship speed data and sea ice forecasts in the Baltic Sea

    U. Löptien

    2014-12-01

    Full Text Available The Baltic Sea is a seasonally ice-covered marginal sea located in a densely populated area in northern Europe. Severe sea ice conditions have the potential to hinder the intense ship traffic considerably. Thus, sea ice fore- and nowcasts are regularly provided by the national weather services. Typically, the forecast comprises several ice properties that are distributed as prognostic variables, but their actual usefulness is difficult to measure, and the ship captains must determine their relative importance and relevance for optimal ship speed and safety ad hoc. The present study provides a more objective approach by comparing the ship speeds, obtained by the automatic identification system (AIS, with the respective forecasted ice conditions. We find that, despite an unavoidable random component, this information is useful to constrain and rate fore- and nowcasts. More precisely, 62–67% of ship speed variations can be explained by the forecasted ice properties when fitting a mixed-effect model. This statistical fit is based on a test region in the Bothnian Sea during the severe winter 2011 and employs 15 to 25 min averages of ship speed.

  5. Application of a viscoplastic constitutive law to lead in the impact analysis of radioactive material shipping casks

    Wang, Zhibi; Turula, P.; Popper, G.F.

    1990-01-01

    Perzyna's viscoplastic material model is selected to consider the strain rate effect of lead used in radioactive material shipping packages. The model is checked using data from two scale-model tests and the deformations are found to be within 10 percent. 3 refs., 4 figs

  6. Thermo-hydraulic characteristics of ship propulsion reactor in the conditions of ship motions and safety assessment

    Kobayashi, Michiyuki; Murata, Hiroyuki; Sawada, Kenichi; Inasaka, Fujio; Aya, Izuo; Shiozaki, Koki

    1999-01-01

    By inputting the experimental data, information and others on thermo-hydraulic characteristics of integrated ship propulsion reactor accumulated hitherto by the Ship Research Institute and some recent cooperation results into the nuclear ship engineering simulation system, it was conducted not only to contribute an improvement study on next ship reactor by executing general analysis and evaluation on motion characteristics under ship body motion conditions, safety at accidents, and others of the integrated ship reactor but also to investigate and prepare some measures to apply fundamental experiment results based on obtained here information to safety countermeasure of the nuclear ships. In 1997 fiscal year, on safety of the integrated ship propulsion reactor loading nuclear ship, by adding experimental data on unstable flow analysis and information on all around of the analysis to general data base fundamental program, development to intellectual data base program was intended; on effect of pulsation flow on thermo-hydraulic characteristics of ship propulsion reactor; after pulsation flow visualization experiment, experimental equipment was reconstructed into heat transfer type to conduct numerical analysis of pulsation flow by confirming validity of numerical analysis code under comparison with the visualization experiment results; and on thermo-hydraulic behavior in storage container at accident of active safety type ship propulsion reactor; a flashing vibration test using new apparatus finished on its higher pressurization at last fiscal year to examine effects of each parameter such as radius and length of exhausting nozzle and pool water temperature. (G.K.)

  7. Testing of a steel containment vessel model

    Luk, V.K.; Hessheimer, M.F.; Matsumoto, T.; Komine, K.; Costello, J.F.

    1997-01-01

    A mixed-scale containment vessel model, with 1:10 in containment geometry and 1:4 in shell thickness, was fabricated to represent an improved, boiling water reactor (BWR) Mark II containment vessel. A contact structure, installed over the model and separated at a nominally uniform distance from it, provided a simplified representation of a reactor shield building in the actual plant. This paper describes the pretest preparations and the conduct of the high pressure test of the model performed on December 11-12, 1996. 4 refs., 2 figs

  8. Precision tests of the Standard Model

    Ol'shevskij, A.G.

    1996-01-01

    The present status of the precision measurements of electroweak observables is discussed with the special emphasis on the results obtained recently. All together these measurements provide the basis for the stringent test of the Standard Model and determination of the SM parameters. 22 refs., 23 figs., 11 tabs

  9. Binomial test models and item difficulty

    van der Linden, Willem J.

    1979-01-01

    In choosing a binomial test model, it is important to know exactly what conditions are imposed on item difficulty. In this paper these conditions are examined for both a deterministic and a stochastic conception of item responses. It appears that they are more restrictive than is generally

  10. Shallow foundation model tests in Europe

    Feda, Jaroslav; Simonini, P.; Arslan, U.; Georgiodis, M.; Laue, J.; Pinto, I.

    1999-01-01

    Roč. 2, č. 4 (1999), s. 447-475 ISSN 1436-6517. [Int. Conf. on Soil - Structure Interaction in Urban Civ. Engineering. Darmstadt, 08.10.1999-09.10.1999] R&D Projects: GA MŠk OC C7.10 Keywords : shallow foundations * model tests * sandy subsoil * bearing capacity * settlement Subject RIV: JM - Building Engineering

  11. Ship operations report, 1973

    1973-01-01

    The NOAA Fleet Operations Report 1973 was developed to provide a summary of project accomplishments during calendar year 1973. The report was prepared from season, cruise and special reports submitted by ships of the fleet. Centralized management of the NOAA Fleet was finalized by changing the operational control of the National Marine Fisheries Service (NMFS) Ships DAVID STARR JORDAN (FRS 44), TOWNSEND CROMWELL (FRS 43) and MURRE II (FRV 63) from NMFS to the National Ocean Survey on July 1, 1973. Throughout the year, ships routinely collected and transmitted weather data. Similarly, as NOAA participants in the Integrated Global Ocean Station System (IGOSS) service program, XBT observations were taken and either radioed or submitted in log form via mail. In addition, particulate and radionuclide samples were taken in cooperation with the Atomic Energy Commission, sediment samples were obtained for the Smithsonian Institution and observations were made of marine mammals

  12. Ship operations report, 1975

    1976-01-01

    The NOAA Ship Operations Report 1975 was developed to provide a summary of projects undertaken during calendar year 1975. The report was prepared from season, cruise and special reports submitted by ships of the fleet. This report is promulgated for inhouse dissemination in the National Oceanic and Atmospheric Administration, for collaborating and interested agencies, and for use by members of the scientific community. Throughout the year, ships routinely collected and transmitted weather data. Similarly, as NOAA participants in the Integrated Global Ocean Station System (IGOSS) service program, XBT observations were taken and either radioed or submitted in log form via mail. In addition, particulate and radionuclide samples were taken in cooperation with the Atomic Energy Commission, sediment samples were obtained for the Smithsonian Institution and observations were made of marine mammals

  13. Internationalisation Within Liner Shipping

    Prockl, Günter; Kinra, Aseem; Kotzab, Herbert

    2018-01-01

    , the degree of internationalisation, measured on the basis of sea-oriented operations, differs from that measured according to land-oriented front-end marketing and sales activities. The purpose of this study is to further examine the internationalisation patterns of shipping lines. An examination...... of the front-end activities and the structures of leading container-shipping companies is conducted. The sales office networks of the sector’s 20 largest companies worldwide (by twenty-foot equivalent unit capacity) are analysed as key indicators. The numbers of sales offices are measured by analysing...... the websites of the sample (20 companies), as well as annual reports and other publicly available data sources. The findings show that not all shipping companies are international, by virtue of the industry. While it is difficult to observe differences in the overall patterns of the sales networks at a macro...

  14. Testing mechanistic models of growth in insects.

    Maino, James L; Kearney, Michael R

    2015-11-22

    Insects are typified by their small size, large numbers, impressive reproductive output and rapid growth. However, insect growth is not simply rapid; rather, insects follow a qualitatively distinct trajectory to many other animals. Here we present a mechanistic growth model for insects and show that increasing specific assimilation during the growth phase can explain the near-exponential growth trajectory of insects. The presented model is tested against growth data on 50 insects, and compared against other mechanistic growth models. Unlike the other mechanistic models, our growth model predicts energy reserves per biomass to increase with age, which implies a higher production efficiency and energy density of biomass in later instars. These predictions are tested against data compiled from the literature whereby it is confirmed that insects increase their production efficiency (by 24 percentage points) and energy density (by 4 J mg(-1)) between hatching and the attainment of full size. The model suggests that insects achieve greater production efficiencies and enhanced growth rates by increasing specific assimilation and increasing energy reserves per biomass, which are less costly to maintain than structural biomass. Our findings illustrate how the explanatory and predictive power of mechanistic growth models comes from their grounding in underlying biological processes. © 2015 The Author(s).

  15. Testing proton spin models with polarized beams

    Ramsey, G.P.

    1991-01-01

    We review models for spin-weighted parton distributions in a proton. Sum rules involving the nonsinglet components of the structure function xg 1 p help narrow the range of parameters in these models. The contribution of the γ 5 anomaly term depends on the size of the integrated polarized gluon distribution and experimental predictions depend on its size. We have proposed three models for the polarized gluon distributions, whose range is considerable. These model distributions give an overall range is considerable. These model distributions give an overall range of parameters that can be tested with polarized beam experiments. These are discussed with regard to specific predictions for polarized beam experiments at energies typical of UNK

  16. Numerical modeling of simultaneous tracer release and piscicide treatment for invasive species control in the Chicago Sanitary and Ship Canal, Chicago, Illinois

    Zhu, Zhenduo; Motta, Davide; Jackson, P. Ryan; Garcia, Marcelo H.

    2017-01-01

    In December 2009, during a piscicide treatment targeting the invasive Asian carp in the Chicago Sanitary and Ship Canal, Rhodamine WT dye was released to track and document the transport and dispersion of the piscicide. In this study, two modeling approaches are presented to reproduce the advection and dispersion of the dye tracer (and piscicide), a one-dimensional analytical solution and a three-dimensional numerical model. The two approaches were compared with field measurements of concentration and their applicability is discussed. Acoustic Doppler current profiler measurements were used to estimate the longitudinal dispersion coefficients at ten cross sections, which were taken as reference for calibrating the longitudinal dispersion coefficient in the one-dimensional analytical solution. While the analytical solution is fast, relatively simple, and can fairly accurately predict the core of the observed concentration time series at points downstream, it does not capture the tail of the breakthrough curves. These tails are well reproduced by the three-dimensional model, because it accounts for the effects of dead zones and a power plant which withdraws nearly 80 % of the water from the canal for cooling purposes before returning it back to the canal.

  17. Testing Parametric versus Semiparametric Modelling in Generalized Linear Models

    Härdle, W.K.; Mammen, E.; Müller, M.D.

    1996-01-01

    We consider a generalized partially linear model E(Y|X,T) = G{X'b + m(T)} where G is a known function, b is an unknown parameter vector, and m is an unknown function.The paper introduces a test statistic which allows to decide between a parametric and a semiparametric model: (i) m is linear, i.e.

  18. OTEC riser cable model and prototype testing

    Kurt, J. P.; Schultz, J. A.; Roblee, L. H. S.

    1981-12-01

    Two different OTEC riser cables have been developed to span the distance between a floating OTEC power plant and the ocean floor. The major design concerns for a riser cable in the dynamic OTEC environment are fatigue, corrosion, and electrical/mechanical aging of the cable components. The basic properties of the cable materials were studied through tests on model cables and on samples of cable materials. Full-scale prototype cables were manufactured and were tested to measure their electrical and mechanical properties and performance. The full-scale testing was culminated by the electrical/mechanical fatigue test, which exposes full-scale cables to simultaneous tension, bending and electrical loads, all in a natural seawater environment.

  19. Shipping emissions in ports

    Merk, Olaf

    2014-01-01

    Shipping emissions in ports are substantial, accounting for 18 million tonnes of CO2 emissions, 0.4 million tonnes of NOx, 0.2 million of SOx and 0.03 million tonnes of PM10 in 2011. Around 85% of emissions come from containerships and tankers. Containerships have short port stays, but high emissions during these stays. Most of CO2 emissions in ports from shipping are in Asia and Europe (58%), but this share is low compared to their share of port calls (70%). European ports have much less emi...

  20. Prospective Tests on Biological Models of Acupuncture

    Charles Shang

    2009-01-01

    Full Text Available The biological effects of acupuncture include the regulation of a variety of neurohumoral factors and growth control factors. In science, models or hypotheses with confirmed predictions are considered more convincing than models solely based on retrospective explanations. Literature review showed that two biological models of acupuncture have been prospectively tested with independently confirmed predictions: The neurophysiology model on the long-term effects of acupuncture emphasizes the trophic and anti-inflammatory effects of acupuncture. Its prediction on the peripheral effect of endorphin in acupuncture has been confirmed. The growth control model encompasses the neurophysiology model and suggests that a macroscopic growth control system originates from a network of organizers in embryogenesis. The activity of the growth control system is important in the formation, maintenance and regulation of all the physiological systems. Several phenomena of acupuncture such as the distribution of auricular acupuncture points, the long-term effects of acupuncture and the effect of multimodal non-specific stimulation at acupuncture points are consistent with the growth control model. The following predictions of the growth control model have been independently confirmed by research results in both acupuncture and conventional biomedical sciences: (i Acupuncture has extensive growth control effects. (ii Singular point and separatrix exist in morphogenesis. (iii Organizers have high electric conductance, high current density and high density of gap junctions. (iv A high density of gap junctions is distributed as separatrices or boundaries at body surface after early embryogenesis. (v Many acupuncture points are located at transition points or boundaries between different body domains or muscles, coinciding with the connective tissue planes. (vi Some morphogens and organizers continue to function after embryogenesis. Current acupuncture research suggests a

  1. Analytical support management shipping company

    S.V. Tarasenko

    2016-12-01

    Full Text Available The article to determine areas of improvement of the economic analysis of the shipping companies tested, allowing to identify the problems of organization and methods, which are as follows: lack of regulation of economic analysis, unregulated and methods of economic analysis, using methods such as coefficient method, absolute differences method relative differences groupings balance method, while as factor analysis and correlation are ignored. Proved that today the priority targets of management that should be subject to economic analysis are: analysis of the efficiency of the fleet; analysis of the efficiency of transport services; analysis of the cost of transport services and costs; analysis of the efficiency of resource use.

  2. Analysis, scale modeling, and full-scale tests of low-level nuclear-waste-drum response to accident environments

    Huerta, M.; Lamoreaux, G.H.; Romesberg, L.E.; Yoshimura, H.R.; Joseph, B.J.; May, R.A.

    1983-01-01

    This report describes extensive full-scale and scale-model testing of 55-gallon drums used for shipping low-level radioactive waste materials. The tests conducted include static crush, single-can impact tests, and side impact tests of eight stacked drums. Static crush forces were measured and crush energies calculated. The tests were performed in full-, quarter-, and eighth-scale with different types of waste materials. The full-scale drums were modeled with standard food product cans. The response of the containers is reported in terms of drum deformations and lid behavior. The results of the scale model tests are correlated to the results of the full-scale drums. Two computer techniques for calculating the response of drum stacks are presented. 83 figures, 9 tables

  3. Physical modelling and testing in environmental geotechnics

    Garnier, J.; Thorel, L.; Haza, E.

    2000-01-01

    The preservation of natural environment has become a major concern, which affects nowadays a wide range of professionals from local communities administrators to natural resources managers (water, wildlife, flora, etc) and, in the end, to the consumers that we all are. Although totally ignored some fifty years ago, environmental geotechnics has become an emergent area of study and research which borders on the traditional domains, with which the geo-technicians are confronted (soil and rock mechanics, engineering geology, natural and anthropogenic risk management). Dedicated to experimental approaches (in-situ investigations and tests, laboratory tests, small-scale model testing), the Symposium fits in with the geotechnical domains of environment and transport of soil pollutants. These proceedings report some progress of developments in measurement techniques and studies of transport of pollutants in saturated and unsaturated soils in order to improve our understanding of such phenomena within multiphase environments. Experimental investigations on decontamination and isolation methods for polluted soils are discussed. The intention is to assess the impact of in-situ and laboratory tests, as well as small-scale model testing, on engineering practice. One paper is analysed in INIS data base for its specific interest in nuclear industry. The other ones, concerning the energy, are analyzed in ETDE data base

  4. Hypervapotron flow testing with rapid prototype models

    Driemeyer, D.; Hellwig, T.; Kubik, D.; Langenderfer, E.; Mantz, H.; McSmith, M.; Jones, B.; Butler, J.

    1995-01-01

    A flow test model of the inlet section of a three channel hypervapotron plate that has been proposed as a heat sink in the ITER divertor was prepared using a rapid prototyping stereolithography process that is widely used for component development in US industry. An existing water flow loop at the University of Illinois is being used for isothermal flow tests to collect pressure drop data for comparison with proposed vapotron friction factor correlations. Differential pressure measurements are taken, across the test section inlet manifold, the vapotron channel (about a seven inch length), the outlet manifold and the inlet-to-outlet. The differential pressures are currently measured with manometers. Tests were conducted at flow velocities from 1--10 m/s to cover the full range of ITER interest. A tap was also added for a small hypodermic needle to inject dye into the flow channel at several positions to examine the nature of the developing flow field at the entrance to the vapotron section. Follow-on flow tests are planned using a model with adjustable flow channel dimensions to permit more extensive pressure drop data to be collected. This information will be used to update vapotron design correlations for ITER

  5. Physical modelling and testing in environmental geotechnics

    Garnier, J.; Thorel, L.; Haza, E. [Laboratoire Central des Ponts et Chaussees a Nantes, 44 - Nantes (France)

    2000-07-01

    The preservation of natural environment has become a major concern, which affects nowadays a wide range of professionals from local communities administrators to natural resources managers (water, wildlife, flora, etc) and, in the end, to the consumers that we all are. Although totally ignored some fifty years ago, environmental geotechnics has become an emergent area of study and research which borders on the traditional domains, with which the geo-technicians are confronted (soil and rock mechanics, engineering geology, natural and anthropogenic risk management). Dedicated to experimental approaches (in-situ investigations and tests, laboratory tests, small-scale model testing), the Symposium fits in with the geotechnical domains of environment and transport of soil pollutants. These proceedings report some progress of developments in measurement techniques and studies of transport of pollutants in saturated and unsaturated soils in order to improve our understanding of such phenomena within multiphase environments. Experimental investigations on decontamination and isolation methods for polluted soils are discussed. The intention is to assess the impact of in-situ and laboratory tests, as well as small-scale model testing, on engineering practice. One paper has been analyzed in INIS data base for its specific interest in nuclear industry.

  6. Quantitative analysis method for ship construction quality

    FU Senzong

    2017-03-01

    Full Text Available The excellent performance of a ship is assured by the accurate evaluation of its construction quality. For a long time, research into the construction quality of ships has mainly focused on qualitative analysis due to a shortage of process data, which results from limited samples, varied process types and non-standardized processes. Aiming at predicting and controlling the influence of the construction process on the construction quality of ships, this article proposes a reliability quantitative analysis flow path for the ship construction process and fuzzy calculation method. Based on the process-quality factor model proposed by the Function-Oriented Quality Control (FOQC method, we combine fuzzy mathematics with the expert grading method to deduce formulations calculating the fuzzy process reliability of the ordinal connection model, series connection model and mixed connection model. The quantitative analysis method is applied in analyzing the process reliability of a ship's shaft gear box installation, which proves the applicability and effectiveness of the method. The analysis results can be a useful reference for setting key quality inspection points and optimizing key processes.

  7. Are nuclear ships environmentally safer than conventionally powered ships

    Bone, C.A.; Molgaard, C.A.; Helmkamp, J.C.; Golbeck, A.L.

    1988-01-01

    An epidemiologic analysis was conducted to determine if risk of hospitalization varied by age, ship type, or occupation between nuclear and conventional powered ship crews in the U.S. Navy. Study cohorts consisted of all male enlisted personnel who served exclusively aboard conventional or nuclear powered aircraft carriers and cruisers during the years 1975-1979; cases were those men hospitalized during this period (N = 48,242). Conventional ship personnel showed significantly elevated rates of injury and disease when compared to nuclear ship personnel. The largest relative risks by age occurred for conventional ship crewmen less than 30 years old. Seaman, logistics (supply), and healthcare personnel serving aboard conventional ships comprised the occupational groups exhibiting the highest hospitalization rate differentials. The results strongly suggest that nuclear ships provide a healthier, safer working and living environment than conventional ships

  8. Horns Rev II, 2-D Model Tests

    Andersen, Thomas Lykke; Frigaard, Peter

    This report present the results of 2D physical model tests carried out in the shallow wave flume at Dept. of Civil Engineering, Aalborg University (AAU), on behalf of Energy E2 A/S part of DONG Energy A/S, Denmark. The objective of the tests was: to investigate the combined influence of the pile...... diameter to water depth ratio and the wave hight to water depth ratio on wave run-up of piles. The measurements should be used to design access platforms on piles....

  9. Temperature Buffer Test. Final THM modelling

    Aakesson, Mattias; Malmberg, Daniel; Boergesson, Lennart; Hernelind, Jan; Ledesma, Alberto; Jacinto, Abel

    2012-01-01

    The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aespoe HRL. It was installed during the spring of 2003. Two heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report presents the final THM modelling which was resumed subsequent to the dismantling operation. The main part of this work has been numerical modelling of the field test. Three different modelling teams have presented several model cases for different geometries and different degree of process complexity. Two different numerical codes, Code B right and Abaqus, have been used. The modelling performed by UPC-Cimne using Code B right, has been divided in three subtasks: i) analysis of the response observed in the lower part of the test, by inclusion of a number of considerations: (a) the use of the Barcelona Expansive Model for MX-80 bentonite; (b) updated parameters in the vapour diffusive flow term; (c) the use of a non-conventional water retention curve for MX-80 at high temperature; ii) assessment of a possible relation between the cracks observed in the bentonite blocks in the upper part of TBT, and the cycles of suction and stresses registered in that zone at the start of the experiment; and iii) analysis of the performance, observations and interpretation of the entire test. It was however not possible to carry out a full THM analysis until the end of the test due to

  10. Temperature Buffer Test. Final THM modelling

    Aakesson, Mattias; Malmberg, Daniel; Boergesson, Lennart; Hernelind, Jan [Clay Technology AB, Lund (Sweden); Ledesma, Alberto; Jacinto, Abel [UPC, Universitat Politecnica de Catalunya, Barcelona (Spain)

    2012-01-15

    The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aespoe HRL. It was installed during the spring of 2003. Two heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report presents the final THM modelling which was resumed subsequent to the dismantling operation. The main part of this work has been numerical modelling of the field test. Three different modelling teams have presented several model cases for different geometries and different degree of process complexity. Two different numerical codes, Code{sub B}right and Abaqus, have been used. The modelling performed by UPC-Cimne using Code{sub B}right, has been divided in three subtasks: i) analysis of the response observed in the lower part of the test, by inclusion of a number of considerations: (a) the use of the Barcelona Expansive Model for MX-80 bentonite; (b) updated parameters in the vapour diffusive flow term; (c) the use of a non-conventional water retention curve for MX-80 at high temperature; ii) assessment of a possible relation between the cracks observed in the bentonite blocks in the upper part of TBT, and the cycles of suction and stresses registered in that zone at the start of the experiment; and iii) analysis of the performance, observations and interpretation of the entire test. It was however not possible to carry out a full THM analysis until the end of the test due to

  11. Observational tests of FRW world models

    Lahav, Ofer

    2002-01-01

    Observational tests for the cosmological principle are reviewed. Assuming the FRW metric we then summarize estimates of cosmological parameters from various datasets, in particular the cosmic microwave background and the 2dF galaxy redshift survey. These and other analyses suggest a best-fit Λ-cold dark matter model with Ω m = 1 - Ω l ∼ 0.3 and H 0 ∼ 70 km s -1 Mpc -1 . It is remarkable that different measurements converge to this 'concordance model', although it remains to be seen if the two main components of this model, the dark matter and the dark energy, are real entities or just 'epicycles'. We point out some open questions related to this fashionable model

  12. Preliminary Test for Constitutive Models of CAP

    Choo, Yeon Joon; Hong, Soon Joon; Hwang, Su Hyun; Lee, Keo Hyung; Kim, Min Ki; Lee, Byung Chul [FNC Tech., Seoul (Korea, Republic of); Ha, Sang Jun; Choi, Hoon [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

    2010-05-15

    The development project for the domestic design code was launched to be used for the safety and performance analysis of pressurized light water reactors. As a part of this project, CAP (Containment Analysis Package) code has been developing for the containment safety and performance analysis side by side with SPACE. The CAP code treats three fields (vapor, continuous liquid and dispersed drop) for the assessment of containment specific phenomena, and is featured by assessment capabilities in multi-dimensional and lumped parameter thermal hydraulic cell. Thermal hydraulics solver was developed and has a significant progress now. Implementation of the well proven constitutive models and correlations are essential in other for a containment code to be used with the generalized or optimized purposes. Generally, constitutive equations are composed of interfacial and wall transport models and correlations. These equations are included in the source terms of the governing field equations. In order to develop the best model and correlation package of the CAP code, various models currently used in major containment analysis codes, such as GOTHIC, CONTAIN2.0 and CONTEMPT-LT are reviewed. Several models and correlations were incorporated for the preliminary test of CAP's performance and test results and future plans to improve the level of execution besides will be discussed in this paper

  13. Preliminary Test for Constitutive Models of CAP

    Choo, Yeon Joon; Hong, Soon Joon; Hwang, Su Hyun; Lee, Keo Hyung; Kim, Min Ki; Lee, Byung Chul; Ha, Sang Jun; Choi, Hoon

    2010-01-01

    The development project for the domestic design code was launched to be used for the safety and performance analysis of pressurized light water reactors. As a part of this project, CAP (Containment Analysis Package) code has been developing for the containment safety and performance analysis side by side with SPACE. The CAP code treats three fields (vapor, continuous liquid and dispersed drop) for the assessment of containment specific phenomena, and is featured by assessment capabilities in multi-dimensional and lumped parameter thermal hydraulic cell. Thermal hydraulics solver was developed and has a significant progress now. Implementation of the well proven constitutive models and correlations are essential in other for a containment code to be used with the generalized or optimized purposes. Generally, constitutive equations are composed of interfacial and wall transport models and correlations. These equations are included in the source terms of the governing field equations. In order to develop the best model and correlation package of the CAP code, various models currently used in major containment analysis codes, such as GOTHIC, CONTAIN2.0 and CONTEMPT-LT are reviewed. Several models and correlations were incorporated for the preliminary test of CAP's performance and test results and future plans to improve the level of execution besides will be discussed in this paper

  14. SHIPPING OF RADIOACTIVE ITEMS

    TIS/RP Group

    2001-01-01

    The TIS-RP group informs users that shipping of small radioactive items is normally guaranteed within 24 hours from the time the material is handed in at the TIS-RP service. This time is imposed by the necessary procedures (identification of the radionuclides, determination of dose rate and massive objects require a longer procedure and will therefore take longer.

  15. Ship Roll Damping Control

    Perez, Tristan; Blanke, Mogens

    2012-01-01

    limitations and large variations of the spectral characteristics of wave-induced roll motion. This tutorial paper presents an account of the development of various ship roll motion control systems together with the challenges associated with their design. It discusses the assessment of performance...

  16. Options of ship discharge

    NONE

    2010-05-15

    Environmental performance is a key design consideration for manufacturers of bulk handling machines, not least ship unloaders, with features being introduced to minimise dust and noise pollution. The article reports on developments in grab unloaders, slewing grabcranes and mobile grabcranes by manufacturers such as Konecrane, EMS-Tech, Liebherr-Werk Nenzing and Gottwald. 2 photos.

  17. Hydroelastic Vibrations of Ships

    Jensen, Jørgen Juncher; Folsø, Rasmus

    2002-01-01

    A formula for the necessary hull girder bending stiffness required to avoid serious springing vibrations is derived. The expression takes into account the zero crossing period of the waves, the ship speed and main dimensions. For whipping vibrations the probability of exceedance for the combined...

  18. Business model stress testing : A practical approach to test the robustness of a business model

    Haaker, T.I.; Bouwman, W.A.G.A.; Janssen, W; de Reuver, G.A.

    Business models and business model innovation are increasingly gaining attention in practice as well as in academic literature. However, the robustness of business models (BM) is seldom tested vis-à-vis the fast and unpredictable changes in digital technologies, regulation and markets. The

  19. Divergence-based tests for model diagnostic

    Hobza, Tomáš; Esteban, M. D.; Morales, D.; Marhuenda, Y.

    2008-01-01

    Roč. 78, č. 13 (2008), s. 1702-1710 ISSN 0167-7152 R&D Projects: GA MŠk 1M0572 Grant - others:Instituto Nacional de Estadistica (ES) MTM2006-05693 Institutional research plan: CEZ:AV0Z10750506 Keywords : goodness of fit * devergence statistics * GLM * model checking * bootstrap Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 0.445, year: 2008 http://library.utia.cas.cz/separaty/2008/SI/hobza-divergence-based%20tests%20for%20model%20diagnostic.pdf

  20. Overload prevention in model supports for wind tunnel model testing

    Anton IVANOVICI

    2015-09-01

    Full Text Available Preventing overloads in wind tunnel model supports is crucial to the integrity of the tested system. Results can only be interpreted as valid if the model support, conventionally called a sting remains sufficiently rigid during testing. Modeling and preliminary calculation can only give an estimate of the sting’s behavior under known forces and moments but sometimes unpredictable, aerodynamically caused model behavior can cause large transient overloads that cannot be taken into account at the sting design phase. To ensure model integrity and data validity an analog fast protection circuit was designed and tested. A post-factum analysis was carried out to optimize the overload detection and a short discussion on aeroelastic phenomena is included to show why such a detector has to be very fast. The last refinement of the concept consists in a fast detector coupled with a slightly slower one to differentiate between transient overloads that decay in time and those that are the result of aeroelastic unwanted phenomena. The decision to stop or continue the test is therefore conservatively taken preserving data and model integrity while allowing normal startup loads and transients to manifest.

  1. Classification of Ship Routing and Scheduling Problems in Liner Shipping

    Kjeldsen, Karina Hjortshøj

    2011-01-01

    This article provides a classification scheme for ship routing and scheduling problems in liner shipping in line with the current and future operational conditions of the liner shipping industry. Based on the classification, the literature is divided into groups whose main characteristics...

  2. Designing healthy communities: Testing the walkability model

    Zuniga-Teran, Adriana; Orr, Barron; Gimblett, Randy; Chalfoun, Nader; Marsh, Stuart; Guertin, David; Going, Scott

    2017-01-01

    Research from multiple domains has provided insights into how neighborhood design can be improved to have a more favorable effect on physical activity, a concept known as walkability. The relevant research findings/hypotheses have been integrated into a Walkability Framework, which organizes the design elements into nine walkability categories. The purpose of this study was to test whether this conceptual framework can be used as a model to measure the interactions between the built environme...

  3. 2-D Model Test of Dolosse Breakwater

    Burcharth, Hans F.; Liu, Zhou

    1994-01-01

    ). To extend the design diagram to cover Dolos breakwaters with superstructure, 2-D model tests of Dolos breakwater with wave wall is included in the project Rubble Mound Breakwater Failure Modes sponsored by the Directorate General XII of the Commission of the European Communities under Contract MAS-CT92......The rational design diagram for Dolos armour should incorporate both the hydraulic stability and the structural integrity. The previous tests performed by Aalborg University (AU) made available such design diagram for the trunk of Dolos breakwater without superstructures (Burcharth et al. 1992...... was on the Dolos breakwater with a high superstructure, where there was almost no overtopping. This case is believed to be the most dangerous one. The test of the Dolos breakwater with a low superstructure was also performed. The objective of the last part of the experiment is to investigate the influence...

  4. Wallops Ship Surveillance System

    Smith, Donna C.

    2011-01-01

    Approved as a Wallops control center backup system, the Wallops Ship Surveillance Software is a day-of-launch risk analysis tool for spaceport activities. The system calculates impact probabilities and displays ship locations relative to boundary lines. It enables rapid analysis of possible flight paths to preclude the need to cancel launches and allow execution of launches in a timely manner. Its design is based on low-cost, large-customer- base elements including personal computers, the Windows operating system, C/C++ object-oriented software, and network interfaces. In conformance with the NASA software safety standard, the system is designed to ensure that it does not falsely report a safe-for-launch condition. To improve the current ship surveillance method, the system is designed to prevent delay of launch under a safe-for-launch condition. A single workstation is designated the controller of the official ship information and the official risk analysis. Copies of this information are shared with other networked workstations. The program design is divided into five subsystems areas: 1. Communication Link -- threads that control the networking of workstations; 2. Contact List -- a thread that controls a list of protected item (ocean vessel) information; 3. Hazard List -- threads that control a list of hazardous item (debris) information and associated risk calculation information; 4. Display -- threads that control operator inputs and screen display outputs; and 5. Archive -- a thread that controls archive file read and write access. Currently, most of the hazard list thread and parts of other threads are being reused as part of a new ship surveillance system, under the SureTrak project.

  5. Inverse hydrochemical models of aqueous extracts tests

    Zheng, L.; Samper, J.; Montenegro, L.

    2008-10-10

    Aqueous extract test is a laboratory technique commonly used to measure the amount of soluble salts of a soil sample after adding a known mass of distilled water. Measured aqueous extract data have to be re-interpreted in order to infer porewater chemical composition of the sample because porewater chemistry changes significantly due to dilution and chemical reactions which take place during extraction. Here we present an inverse hydrochemical model to estimate porewater chemical composition from measured water content, aqueous extract, and mineralogical data. The model accounts for acid-base, redox, aqueous complexation, mineral dissolution/precipitation, gas dissolution/ex-solution, cation exchange and surface complexation reactions, of which are assumed to take place at local equilibrium. It has been solved with INVERSE-CORE{sup 2D} and been tested with bentonite samples taken from FEBEX (Full-scale Engineered Barrier EXperiment) in situ test. The inverse model reproduces most of the measured aqueous data except bicarbonate and provides an effective, flexible and comprehensive method to estimate porewater chemical composition of clays. Main uncertainties are related to kinetic calcite dissolution and variations in CO2(g) pressure.

  6. Added masses of ship structures

    Korotkin, Alexandr I

    2008-01-01

    This essentially self-contained reference book contains data on added masses of ships and various ship and marine engineering structures. Theoretical and experimental methods for determining added masses of these objects are described.

  7. Ship Observations - VOS and Navy

    National Oceanic and Atmospheric Administration, Department of Commerce — Combination of Voluntary Observing Ship (VOS) and US Navy Ship weather observations. Obs generally taken 2-4 times daily at 00, 06, 12, and 18z.

  8. Movable scour protection. Model test report

    Lorenz, R.

    2002-07-01

    This report presents the results of a series of model tests with scour protection of marine structures. The objective of the model tests is to investigate the integrity of the scour protection during a general lowering of the surrounding seabed, for instance in connection with movement of a sand bank or with general subsidence. The scour protection in the tests is made out of stone material. Two different fractions have been used: 4 mm and 40 mm. Tests with current, with waves and with combined current and waves were carried out. The scour protection material was placed after an initial scour hole has evolved in the seabed around the structure. This design philosophy has been selected because the situation often is that the scour hole starts to generate immediately after the structure has been placed. It is therefore difficult to establish a scour protection at the undisturbed seabed if the scour material is placed after the main structure. Further, placing the scour material in the scour hole increases the stability of the material. Two types of structure have been used for the test, a Monopile and a Tripod foundation. Test with protection mats around the Monopile model was also carried out. The following main conclusions have emerged form the model tests with flat bed (i.e. no general seabed lowering): 1. The maximum scour depth found in steady current on sand bed was 1.6 times the cylinder diameter, 2. The minimum horizontal extension of the scour hole (upstream direction) was 2.8 times the cylinder diameter, corresponding to a slope of 30 degrees, 3. Concrete protection mats do not meet the criteria for a strongly erodible seabed. In the present test virtually no reduction in the scour depth was obtained. The main problem is the interface to the cylinder. If there is a void between the mats and the cylinder, scour will develop. Even with the protection mats that are tightly connected to the cylinder, scour is expected to develop as long as the mats allow for

  9. Update on emissions and environmental impacts from the international fleet of ships: the contribution from major ship types and ports

    S. B. Dalsøren

    2009-03-01

    Full Text Available A reliable and up-to-date ship emission inventory is essential for atmospheric scientists quantifying the impact of shipping and for policy makers implementing regulations and incentives for emission reduction. The emission modelling in this study takes into account ship type and size dependent input data for 15 ship types and 7 size categories. Global port arrival and departure data for more than 32 000 merchant ships are used to establish operational profiles for the ship segments. The modelled total fuel consumption amounts to 217 Mt in 2004 of which 11 Mt is consumed in in-port operations. This is in agreement with international sales statistics. The modelled fuel consumption is applied to develop global emission inventories for CO2, NO2, SO2, CO, CH4, VOC (Volatile Organic Compounds, N2O, BC (Black Carbon and OC (Organic Carbon. The global emissions from ships at sea and in ports are distributed geographically, applying extended geographical data sets covering about 2 million global ship observations and global port data for 32 000 ships. In addition to inventories for the world fleet, inventories are produced separately for the three dominating ship types, using ship type specific emission modelling and traffic distributions.

    A global Chemical Transport Model (CTM was used to calculate the environmental impacts of the emissions. We find that ship emissions is a dominant contributor over much of the world oceans to surface concentrations of NO2 and SO2. The contribution is also large over some coastal zones. For surface ozone the contribution is high over the oceans but clearly also of importance over Western North America (contribution 15–25% and Western Europe (5–15%. The contribution to tropospheric column ozone is up to 5–6%. The overall impact of ship emissions on global methane lifetime is large due to the high NOx emissions. With

  10. Thurstonian models for sensory discrimination tests as generalized linear models

    Brockhoff, Per B.; Christensen, Rune Haubo Bojesen

    2010-01-01

    as a so-called generalized linear model. The underlying sensory difference 6 becomes directly a parameter of the statistical model and the estimate d' and it's standard error becomes the "usual" output of the statistical analysis. The d' for the monadic A-NOT A method is shown to appear as a standard......Sensory discrimination tests such as the triangle, duo-trio, 2-AFC and 3-AFC tests produce binary data and the Thurstonian decision rule links the underlying sensory difference 6 to the observed number of correct responses. In this paper it is shown how each of these four situations can be viewed...

  11. Trends of shipping markets development

    Tomasz Nowosielski

    2012-06-01

    Full Text Available Shipping markets are dependent on international trade transactions that generate transport needs. These needs can dynamically change depending on global natural resources and commodity markets situation. The changes affecting shipping markets can also be caused by changes to the existing cargo flows and by establishing new ones in different geographies. It is anticipated that in the future shipping markets will change, visible by a decline in shipping in North America and Europe and an increase in Asia.

  12. Blast Testing and Modelling of Composite Structures

    Giversen, Søren

    The motivation for this work is based on a desire for finding light weight alternatives to high strength steel as the material to use for armouring in military vehicles. With the use of high strength steel, an increase in the level of armouring has a significant impact on the vehicle weight......, affecting for example the manoeuvrability and top speed negatively, which ultimately affects the safety of the personal in the vehicle. Strong and light materials, such as fibre reinforced composites, could therefore act as substitutes for the high strength steel, and minimize the impact on the vehicle...... work this set-up should be improved such that the modelled pressure can be validated. For tests performed with a 250g charge load comparisons with model data showed poor agreement. This was found to be due to improper design of the modelled laminate panels, where the layer interface delamination...

  13. BIOMOVS test scenario model comparison using BIOPATH

    Grogan, H.A.; Van Dorp, F.

    1986-07-01

    This report presents the results of the irrigation test scenario, presented in the BIOMOVS intercomparison study, calculated by the computer code BIOPATH. This scenario defines a constant release of Tc-99 and Np-237 into groundwater that is used for irrigation. The system of compartments used to model the biosphere is based upon an area in northern Switzerland and is essentially the same as that used in Projekt Gewaehr to assess the radiological impact of a high level waste repository. Two separate irrigation methods are considered, namely ditch and overhead irrigation. Their influence on the resultant activities calculated in the groundwater, soil and different foodproducts, as a function of time, is evaluated. The sensitivity of the model to parameter variations is analysed which allows a deeper understanding of the model chain. These results are assessed subjectively in a first effort to realistically quantify the uncertainty associated with each calculated activity. (author)

  14. Thermal modelling of Advanced LIGO test masses

    Wang, H; Dovale Álvarez, M; Mow-Lowry, C M; Freise, A; Blair, C; Brooks, A; Kasprzack, M F; Ramette, J; Meyers, P M; Kaufer, S; O’Reilly, B

    2017-01-01

    High-reflectivity fused silica mirrors are at the epicentre of today’s advanced gravitational wave detectors. In these detectors, the mirrors interact with high power laser beams. As a result of finite absorption in the high reflectivity coatings the mirrors suffer from a variety of thermal effects that impact on the detectors’ performance. We propose a model of the Advanced LIGO mirrors that introduces an empirical term to account for the radiative heat transfer between the mirror and its surroundings. The mechanical mode frequency is used as a probe for the overall temperature of the mirror. The thermal transient after power build-up in the optical cavities is used to refine and test the model. The model provides a coating absorption estimate of 1.5–2.0 ppm and estimates that 0.3 to 1.3 ppm of the circulating light is scattered onto the ring heater. (paper)

  15. Testing substellar models with dynamical mass measurements

    Liu M.C.

    2011-07-01

    Full Text Available We have been using Keck laser guide star adaptive optics to monitor the orbits of ultracool binaries, providing dynamical masses at lower luminosities and temperatures than previously available and enabling strong tests of theoretical models. We have identified three specific problems with theory: (1 We find that model color–magnitude diagrams cannot be reliably used to infer masses as they do not accurately reproduce the colors of ultracool dwarfs of known mass. (2 Effective temperatures inferred from evolutionary model radii are typically inconsistent with temperatures derived from fitting atmospheric models to observed spectra by 100–300 K. (3 For the only known pair of field brown dwarfs with a precise mass (3% and age determination (≈25%, the measured luminosities are ~2–3× higher than predicted by model cooling rates (i.e., masses inferred from Lbol and age are 20–30% larger than measured. To make progress in understanding the observed discrepancies, more mass measurements spanning a wide range of luminosity, temperature, and age are needed, along with more accurate age determinations (e.g., via asteroseismology for primary stars with brown dwarf binary companions. Also, resolved optical and infrared spectroscopy are needed to measure lithium depletion and to characterize the atmospheres of binary components in order to better assess model deficiencies.

  16. High cost for drilling ships

    Hooghiemstra, J.

    2007-01-01

    Prices for the rent of a drilling ship are very high. Per day the rent is 1% of the price for building such a ship, and those prices have risen as well. Still, it is attractive for oil companies to rent a drilling ship [nl

  17. Model of a Nuclear Security Naval Agency for radiation control of the Industrial Complex of of Submarine Construction and Maintenance Ship with Nuclear Propulsion

    Lins Junior, Amilton de Sousa

    2017-01-01

    Due to the construction, by Brazilian Navy, of a Submarine Construction and Maintenance Ship with Nuclear Propulsion, where, among other activities, the commissioning and exchange of the fuel elements of the reactor in the future Nuclear Submarine, and of a Naval Base where the Nuclear Submarine and the Conventional Submarines, it is necessary the establishment of a Nuclear Security Naval Agency to monitor activities involving ionizing radiation sources and nuclear materials aimed at the radiological protection of exposed occupationally individuals (IOE), the general public and the environment. It should be noted that nuclear and radioactive material will be present only in a part of the yard called Radiological Complex. Therefore, the development of a structure for the control of the Radiological Complex is fundamental, considering that the future licensing process will be unprecedented in Brazil and will face several difficulties. This work presents a model of a structure for the radiological control of the industrial complex for the construction and maintenance of the submarine with nuclear propulsion, as well as the fundamental concepts of the activities, such as inspection, regulations and authorizations, to be carried out by the various component sectors of the Nuclear Security Naval Agency. (author)

  18. Seepage Calibration Model and Seepage Testing Data

    Dixon, P.

    2004-01-01

    The purpose of this Model Report is to document the Seepage Calibration Model (SCM). The SCM is developed (1) to establish the conceptual basis for the Seepage Model for Performance Assessment (SMPA), and (2) to derive seepage-relevant, model-related parameters and their distributions for use in the SMPA and seepage abstraction in support of the Total System Performance Assessment for License Application (TSPA-LA). The SCM is intended to be used only within this Model Report for the estimation of seepage-relevant parameters through calibration of the model against seepage-rate data from liquid-release tests performed in several niches along the Exploratory Studies Facility (ESF) Main Drift and in the Cross Drift. The SCM does not predict seepage into waste emplacement drifts under thermal or ambient conditions. Seepage predictions for waste emplacement drifts under ambient conditions will be performed with the SMPA (see upcoming REV 02 of CRWMS M and O 2000 [153314]), which inherits the conceptual basis and model-related parameters from the SCM. Seepage during the thermal period is examined separately in the Thermal Hydrologic (TH) Seepage Model (see BSC 2003 [161530]). The scope of this work is (1) to evaluate seepage rates measured during liquid-release experiments performed in several niches in the Exploratory Studies Facility (ESF) and in the Cross Drift, which was excavated for enhanced characterization of the repository block (ECRB); (2) to evaluate air-permeability data measured in boreholes above the niches and the Cross Drift to obtain the permeability structure for the seepage model; (3) to use inverse modeling to calibrate the SCM and to estimate seepage-relevant, model-related parameters on the drift scale; (4) to estimate the epistemic uncertainty of the derived parameters, based on the goodness-of-fit to the observed data and the sensitivity of calculated seepage with respect to the parameters of interest; (5) to characterize the aleatory uncertainty

  19. Thermo-hydraulic characteristics of ship propulsion reactor in the conditions of ship motions and safety assessment

    Kobayashi, Michiyuki; Aya, Izuo; Inasaka, Fujio; Murata, Hiroyuki; Odano, Naoteru; Shiozaki, Koki

    1998-01-01

    A research project from 1995-1999 had a plan to make experimental studies on (1) safety of nuclear ship loaded with an integral ship propulsion reactor (2) effects of pulsating flow on the thermo-hydraulic characteristics of ship propulsion reactor and (3) thermo-hydraulic behaviors of the reactor container at the time of accident in a passively safe ship propulsion reactor. Development of a data base for ship propulsion reactor was attempted using previous experimental data on the thermo-hydraulic characteristics of the reactor in the institute in addition to the present results aiming to make general analytical evaluation for the safety of the engineering-simulation system for nuclear ship. A general data base was obtained by integrating the data list and the analytical program for static characteristics. A test equipment which allows to visualize the pulsating flow was produced and visualization experiments have started. (M.N.)

  20. Large scale injection test (LASGIT) modelling

    Arnedo, D.; Olivella, S.; Alonso, E.E.

    2010-01-01

    Document available in extended abstract form only. With the objective of understanding the gas flow processes through clay barriers in schemes of radioactive waste disposal, the Lasgit in situ experiment was planned and is currently in progress. The modelling of the experiment will permit to better understand of the responses, to confirm hypothesis of mechanisms and processes and to learn in order to design future experiments. The experiment and modelling activities are included in the project FORGE (FP7). The in situ large scale injection test Lasgit is currently being performed at the Aespoe Hard Rock Laboratory by SKB and BGS. An schematic layout of the test is shown. The deposition hole follows the KBS3 scheme. A copper canister is installed in the axe of the deposition hole, surrounded by blocks of highly compacted MX-80 bentonite. A concrete plug is placed at the top of the buffer. A metallic lid anchored to the surrounding host rock is included in order to prevent vertical movements of the whole system during gas injection stages (high gas injection pressures are expected to be reached). Hydration of the buffer material is achieved by injecting water through filter mats, two placed at the rock walls and two at the interfaces between bentonite blocks. Water is also injected through the 12 canister filters. Gas injection stages are performed injecting gas to some of the canister injection filters. Since the water pressure and the stresses (swelling pressure development) will be high during gas injection, it is necessary to inject at high gas pressures. This implies mechanical couplings as gas penetrates after the gas entry pressure is achieved and may produce deformations which in turn lead to permeability increments. A 3D hydro-mechanical numerical model of the test using CODE-BRIGHT is presented. The domain considered for the modelling is shown. The materials considered in the simulation are the MX-80 bentonite blocks (cylinders and rings), the concrete plug