WorldWideScience

Sample records for shift technical engineers

  1. Alternative approaches to providing engineering expertise on shift

    International Nuclear Information System (INIS)

    Olson, J.; Schreiber, R.E.; Melber, B.D.

    1984-05-01

    This report represents the conclusions of a project studying the role of engineering expertise on shift in nuclear power plants. Using the present shift technical advisor (STA) position as the base case, several alternatives are analyzed. On-shift alternatives included the STA, the SS (shift supervisor), and the SE (shift engineer). The SE is degreed, experienced, trained, and licensed as a Senior Reactor Operator. Some non-shift alternatives were also studied. These included a cadre of on-call engineers and specialists within continual contact and easy reach of the plant; a technical system of phone and data lines linking the plant with a facility similar to an on-site technical support center; and finally, an SPDS (safety parameter display system) to agument technical upgrading of operator aids presently available. Potential problems considered in the analysis of implementation of these alternatives included job content constraints, problems of crew acceptance, and problems of labor supply and retention. Of the considered alternatives, the SE and SS options appear superior to the current STA approach. The SE approach appears the easiest to implement and the most effective under varied plant conditions. The SE may also serve as liaison to off-site support facilities

  2. Experience with the shift technical advisor position

    International Nuclear Information System (INIS)

    Melber, B.D.; Olson, J.; Schreiber, R.E.; Winges, L.

    1984-03-01

    The provision of engineering expertise on shift at commercial nuclear power plants has mainly taken the form of the Shift Technical Advisor (STA). This person, acting in a capacity that is part engineer and part operator, is expected to advise the operations crew in the event of an emergency and review plant operating experience during normal circumstances. The position was mandated by the Nuclear Regulatory Commission following the incident at Three Mile Island. This report expands on a growing body of knowledge regarding the effectiveness of the STA. The new data presented here come from interviews with plant personnel and utility officials from nine sites. Researchers from the Pacific Northwest Laboratory (PNL) interviewed plant personnel, including the STA and immediate management, the shift supervisor and management, the training department, and ancillary staff, all of whom affect the intended performance of the STA. The conclusions of the report are that the design of the STA position results in limited contribution during emergencies; more comprehensive ways should be sought to provide the variety and specificity of engineering expertise needed during such times

  3. Experience with the shift technical advisor position

    Energy Technology Data Exchange (ETDEWEB)

    Melber, B.D.; Olson, J.; Schreiber, R.E.; Winges, L.

    1984-03-01

    The provision of engineering expertise on shift at commercial nuclear power plants has mainly taken the form of the Shift Technical Advisor (STA). This person, acting in a capacity that is part engineer and part operator, is expected to advise the operations crew in the event of an emergency and review plant operating experience during normal circumstances. The position was mandated by the Nuclear Regulatory Commission following the incident at Three Mile Island. This report expands on a growing body of knowledge regarding the effectiveness of the STA. The new data presented here come from interviews with plant personnel and utility officials from nine sites. Researchers from the Pacific Northwest Laboratory (PNL) interviewed plant personnel, including the STA and immediate management, the shift supervisor and management, the training department, and ancillary staff, all of whom affect the intended performance of the STA. The conclusions of the report are that the design of the STA position results in limited contribution during emergencies; more comprehensive ways should be sought to provide the variety and specificity of engineering expertise needed during such times.

  4. Commonwealth Edison's approach to enhanced on-shift technical capability

    International Nuclear Information System (INIS)

    Toscas, J.G.

    1981-01-01

    A long-term plan was formulated that called for the integration of accident assessment and operational supervisory functions into a new operating position called the Station Control Room Engineer (SCRE). Pending implementation of the long-term plan, an alternative to the Shift Technical Advisor concept was selected as an interim plan. This alternative, called the SRO Augmentation program, involved giving five modules of specialized training to shift Senior Operators

  5. Engineering expertise on shift in nuclear power plants: the foreign experience

    International Nuclear Information System (INIS)

    Melber, B.D.; Schreiber, R.E.

    1983-02-01

    This report describes the practices of selected foreign countries with providing engineering expertise on shift in nuclear power plants. The extent to which engineering expertise is made available and the alternative models of providing such expertise are presented. The implications of foreign practices for US consideration of alternatives are discussed, with reference to the shift technical advisor (STA) position and to a proposed shift engineer position. The procedure used to obtain information on foreign practices was primarily a review of the literature, including publications, presentations, and government and utility reports. There are two approaches that are in use to make engineering expertise available on shift: (1) employing a graduate engineer in a line management operations position; and (2) creating a specific engineering position for the purpose of providing expertise to the operations staff

  6. Academic involvement in shift technical advisor training for the utilities

    International Nuclear Information System (INIS)

    Davidson, J.N.; Sain, L.H.

    1981-01-01

    One of the clearest conclusions reached of nearly every commission and panel formed in response to the Three Mile Island accident was the desirability of upgrading the educational background of those persons with direct operational responsibility in a nuclear power plant. The long term objective is for all shift supervisors to have engineering degrees as well as NRC senior operating licenses. In the interim, the utilities are required to provide in-depth engineering expertise on every shift in the person of a Shift Technical Advisor (STA). The training of STA's is complicated by the requirement to have college level instruction in plant specific topics which are not typically included in the curricula of degree-granting instructions. One possible response to this challenge is presented

  7. Engineering Technical Review Planning Briefing

    Science.gov (United States)

    Gardner, Terrie

    2012-01-01

    The general topics covered in the engineering technical planning briefing are 1) overviews of NASA, Marshall Space Flight Center (MSFC), and Engineering, 2) the NASA Systems Engineering(SE) Engine and its implementation , 3) the NASA Project Life Cycle, 4) MSFC Technical Management Branch Services in relation to the SE Engine and the Project Life Cycle , 5) Technical Reviews, 6) NASA Human Factor Design Guidance , and 7) the MSFC Human Factors Team. The engineering technical review portion of the presentation is the primary focus of the overall presentation and will address the definition of a design review, execution guidance, the essential stages of a technical review, and the overall review planning life cycle. Examples of a technical review plan content, review approaches, review schedules, and the review process will be provided and discussed. The human factors portion of the presentation will focus on the NASA guidance for human factors. Human factors definition, categories, design guidance, and human factor specialist roles will be addressed. In addition, the NASA Systems Engineering Engine description, definition, and application will be reviewed as background leading into the NASA Project Life Cycle Overview and technical review planning discussion.

  8. Nuclear power plant shift technical advisor. Recommendations for position description, qualifications, education and training

    International Nuclear Information System (INIS)

    1981-01-01

    The purpose of this document is to describe the position and identify specific areas of formal education, plant-specific training and experience necessary to assure an advanced level of analytical ability on shift. These recommendations will provide a level of technical ability that is essential to improved operational safety and are consistent with regulatory requirements. This position was developed in conjunction with representatives of utilities, equipment vendors and engineering educators, giving consideration to specific contributions the function must make to shift operations

  9. Shift technical advisors: in the eyes of the NRC

    International Nuclear Information System (INIS)

    Crocker, L.P.

    1981-01-01

    Since January 1, 1980, the NRC has required that Shift Technical Advisors be on-shift at all operating nuclear power plants. The objective of the requirement is to assure that technical expertise is immediately available to each operating shift to assess off-normal events and to provide advice to control room personnel. Further, this advice and assistance is to be provided by an individual not responsible for control manipulations or for directing the activities of reactor operators. The long-term requirement for on-shift technical expertise is firm. However, the exact manner in which this expertise must be furnished has not been determined. Licensees have proposed various alternatives to meet this requirement. These proposals still are being reviewed by the NRC staff

  10. Mechanical Engineering Department Technical Review

    International Nuclear Information System (INIS)

    Carr, R.B.; Denney, R.M.

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication

  11. Expressive/Exploratory Technical Writing (XTW) in Engineering: Shifting the Technical Writing Curriculum

    Science.gov (United States)

    Warnock, Scott; Kahn, Michael

    2007-01-01

    While the importance of "expressive writing," or informal, self-directed writing, has been well established, teachers underutilize it, particularly in technical writing courses. We introduce the term expressive/exploratory technical writing (XTW), which is the use of informal, self-directed writing to problem-solve in technical fields. We describe…

  12. Mechanical Engineering Department technical review

    Energy Technology Data Exchange (ETDEWEB)

    Carr, R.B.; Abrahamson, L.; Denney, R.M.; Dubois, B.E (eds.)

    1982-01-01

    Technical achievements and publication abstracts related to research in the following Divisions of Lawrence Livermore Laboratory are reported in this biannual review: Nuclear Fuel Engineering; Nuclear Explosives Engineering; Weapons Engineering; Energy Systems Engineering; Engineering Sciences; Magnetic Fusion Engineering; and Material Fabrication. (LCL)

  13. Mechanical Engineering Department technical abstracts

    International Nuclear Information System (INIS)

    1984-01-01

    The Mechanical Engineering Department publishes abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). General information about the current role and activities of each of the Department's seven divisions precedes the technical abstracts. Further information about a division's work may be obtained from the division leader, whose name is given at the end of each divisional summary. The Department's seven divisions are as follows: Nuclear Test Engineering Division, Nuclear Explosives Engineering Division, Weapons Engineering Division, Energy Systems Engineering Division, Engineering Sciences Division, Magnetic Fusion Engineering Division and Materials Fabrication Division

  14. Education and training of the shift technical advisor

    International Nuclear Information System (INIS)

    Thomas, E.L.

    1981-01-01

    This paper discusses the background and current approaches for qualifying the required position of Shift Technical Advisor (STA). Industry positions regarding the regulation are given. Problems associated with meeting the requirement are identified, along with a discussion of other alternatives for upgrading the education level of shift management. Inherent in the discussion is the conclusion that voluntary improvements in the training and education of shift management personnel are more effective than mandatory positions or degree requirements

  15. Guide to good practices for the selection, training, and qualification of shift technical advisors

    Energy Technology Data Exchange (ETDEWEB)

    1993-02-01

    The DOE Guide to Good Practices For The Selection, Training, and Qualification of Shift Technical Advisors can be used by any DOE nuclear facility that has implemented the shift technical advisor position. DOE Order 5480-20, ``Personnel Selection, Qualification, Training, and Staffing Requirements at DOE Reactor and Non-Reactor Nuclear Facilities,`` states that only Category A reactors must use shift technical advisor position. However, many DOE nuclear facilities have implemented the shift technical advisor position to provide independent on-shift technical advice and counsel to the shift operating personnel to help determine cause and mitigation of facility accidents. Those DOE nuclear facilities that have implemented or are going to implement the shift technical advisor position will find this guide useful. This guide addresses areas that may be covered by other training programs. In these cases, it is unnecessary (and undesirable) to duplicate these areas in the STA training program as long as the specific skills and knowledge essential for STAs are addressed. The guide is presented based on the premise that the trainee has not completed any facility-specific training other than general employee training.

  16. Negotiating cultural encounters narrating intercultural engineering and technical communication

    CERN Document Server

    Yu, Han

    2013-01-01

    Discusses the challenges of intercultural communication in engineering, technical, and related professional fields Given today's globalized technical and engineering environment, intercultural communication is an essential topic for engineers, other technical professionals, and technical communicators to learn. Engineering programs, in particular, need to think about how to address the ABET requirement for students to develop global competence and communication skills. This book will help readers learn what intercultural communication is like in the workplace-which is an import

  17. Mechanical Engineering Department technical abstracts

    International Nuclear Information System (INIS)

    Denney, R.M.

    1982-01-01

    The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts

  18. Mechanical Engineering Department. Technical review

    Energy Technology Data Exchange (ETDEWEB)

    Simecka, W.B.; Condouris, R.A.; Talaber, C. (eds.)

    1980-01-01

    The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work.

  19. Mechanical engineering department technical review

    International Nuclear Information System (INIS)

    Carr, R.B.; Denney, R.M.

    1981-01-01

    The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work

  20. Mechanical Engineering Department. Technical review

    International Nuclear Information System (INIS)

    Simecka, W.B.; Condouris, R.A.; Talaber, C.

    1980-01-01

    The Mechanical Engineering Department Technical Review is published to (1) inform the readers of various technical activities within the Department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical achievements and publication abstracts. The first is divided into eight sections, one for each Division in the Department providing the reader with the names of the personnel and the Division accomplishing the work

  1. Engineering Technical Support Center (ETSC)

    Science.gov (United States)

    ETSC is EPA’s technical support and resource centers responsible for providing specialized scientific and engineering support to decision-makers in the Agency’s ten regional offices, states, communities, and local businesses.

  2. Engineering Technical Support Center Annual Report Fiscal ...

    Science.gov (United States)

    The United States Environmental Protection Agency (EPA or Agency) Office of Research and Development (ORD) created the Engineering Technical Support Center (ETSC) in 1987, one of several technical support centers created as part of the Technical Support Project (TSP). ETSC provides engineering expertise to Agency program and regional offices and remediation teams working at contaminated sites across the country. The ETSC is operated within ORD’s Land Remediation and Pollution Control Division (LRPCD) of the National Risk Management Research Laboratory (NRMRL) in Cincinnati, Ohio. The ETSC’s mission is to provide site-specific scientific and engineering technical support to Remedial Project Managers, On-Scene Coordinators, and other remediation personnel at contaminated sites. This allows local, regional, or national authorities to work more quickly, efficiently, and cost effectively, while also increasing the technical experience of the remediation team. Since its inception, the ETSC has supported countless projects across all EPA Regions in almost all states and territories. This report highlights significant projects the ETSC supported in fiscal year 2015 (FY15). These projects addressed an array of environmental scenarios, such as remote mining contamination, expansive landfill waste, cumulative impacts from multiple contamination sources, and persistent threats from abandoned industrial sites. Constructing and testing new and innovative treatment technol

  3. Quantifying resilience for resilience engineering of socio technical systems

    OpenAIRE

    Häring, Ivo; Ebenhöch, Stefan; Stolz, Alexander

    2016-01-01

    Resilience engineering can be defined to comprise originally technical, engineering and natural science approaches to improve the resilience and sustainability of socio technical cyber-physical systems of various complexities with respect to disruptive events. It is argued how this emerging interdisciplinary technical and societal science approach may contribute to civil and societal security research. In this context, the article lists expected benefits of quantifying resilience. Along the r...

  4. Limitation of Piston Centre Shift in Free Piston Stirling Engines

    Energy Technology Data Exchange (ETDEWEB)

    Van der Woude, R.R. [ECN Energy in the Built Environment and Networks, Petten (Netherlands)

    2006-09-15

    Piston centre shift is one of the phenomena setting Free Piston engines apart from traditional kinematic engines. In kinematic engines the piston centre position is determined by the design of the engine's internal mechanisms. In Free Piston engines however, the piston's mid-stroke position is determined by the balance of forces acting on the piston, in particular flexure and gas pressure forces. As a result, a mean pressure difference across the piston emerging during engine operation will cause the piston mid-stroke position to shift away from the geometrical centre. This process will continue until a new balance is reached with the flexure forces counteracting the new mean pressure balance. Yet, before the new equilibrium is reached, the resulting piston centre shift may have grown to such an extent that piston overstrokes have become inevitable. In order to limit piston centre shift and prevent piston overstrokes, several solutions have been proposed in the past. Popular solutions include ingenious mechanisms to vent gas between the spaces separated by the piston, in an attempt to limit the pressure difference. Enatec however has adopted a different approach by applying a precisely determined clearance between the piston and cylinder. With the right shape the clearance effectively limits the mean pressure difference across the piston and therefore limits the extent of the piston centre drift. Taking benefit of tightly controlled tolerances of both piston and cylinder, Enatec has demonstrated the effectiveness of this simple concept in series produced engines.

  5. 100 Areas technical activities report, engineers - March 1951

    Energy Technology Data Exchange (ETDEWEB)

    1951-04-01

    This is the monthly 100 areas technical activities report from the engineering division for the month of March 1951. It reports on engineering activities related directly to the different production reactors, and gives progress reports on various engineering projects which are in development by the engineering group.

  6. Collaborating for Success: Team Teaching the Engineering Technical Thesis

    Science.gov (United States)

    Keating, Terrence; Long, Mike

    2012-01-01

    This paper will examine the collaborative teaching process undertaken at College of the North Atlantic-Qatar (CNA-Q) by Engineering and the Communication faculties to improve the overall quality of engineering students' capstone projects known as the Technical Thesis. The Technical Thesis is divided into two separate components: a proposal stage…

  7. Initial Validation of a Technical Writing Rubric for Engineering Design

    Directory of Open Access Journals (Sweden)

    Cheryl Bodnar

    2018-02-01

    Full Text Available Engineering design serves as the capstone experience of most undergraduate engineering programs. One of the key elements of the engineering design process is the compilation of results obtained into a technical report that can be shared and distributed to interested stakeholders including industry, faculty members and other relevant parties. In an effort to expand the tools available for assessment of engineering design technical reports, this study performed an initial validation of a previously developed Technical Writing rubric. The rubric was evaluated for its reliability to measure the intended construct, inter-rater reliability and external validity in comparison to an existing generalized written communication rubric. It was found that the rubric was reliable with Cronbach’s alpha for all dimensions between 0.817 and 0.976. The inter-rater reliability for the overall instrument was also found to be excellent at 0.85. Finally, it was observed that there were no statistically significant differences observed between the measurements obtained on the Technical Writing rubric in comparison to the more generalized Written Communication Value rubric. This demonstrates that although specific to engineering design environments the Technical Writing rubric was able to measure key constructs associated with written communication practice. This rubric can now serve as one additional tool for assessment of communication skills within engineering capstone design experiences.

  8. Engineering Technical Support Center Annual Report Fiscal Year 2015

    Science.gov (United States)

    The United States Environmental Protection Agency (EPA or Agency) Office of Research and Development (ORD) created the Engineering Technical Support Center (ETSC) in 1987, one of several technical support centers created as part of the Technical Support Project (TSP). ETSC provid...

  9. [The Engineering and Technical Services Directorate at the Glenn Research Center

    Science.gov (United States)

    Moon, James

    2004-01-01

    My name is James Moon and I am a senior at Tennessee State University where my major is Aeronautical and Industrial Technology with a concentration in industrial electronics. I am currently serving my internship in the Engineering and Technical Services Directorate at the Glenn Research Center (GRC). The Engineering and Technical Service Directorate provides the services and infrastructure for the Glenn Research Center to take research concepts to reality. They provide a full range of integrated services including engineering, advanced prototyping and testing, facility management, and information technology for NASA, industry, and academia. Engineering and Technical Services contains the core knowledge in Information Technology (IT). This includes data systems and analysis, inter and intranet based systems design and data security. Including the design and development of embedded real-time s o h a r e applications for flight and supporting ground systems, Engineering and Technical Services provide a wide range of IT services and products specific to the Glenn Research Center research and engineering community. In the 7000 Directorate I work directly in the 7611 organization. This organization is known as the Aviation Environments Technical Branch. My mentor is Vincent Satterwhite who is also the Branch Chief of the Aviation Environments Technical Branch. In this branch, I serve as the Assistant program manager of the Engineering Technology Program. The Engineering Technology Program (ETP) is one of three components of the High School L.E.R.C.I.P. This is an Agency-sponsored, eight-week research-based apprenticeship program designed to attract traditionally underrepresented high school students that demonstrate an aptitude for and interest in mathematics, science, engineering, and technology.

  10. Engineering and Technical Education in Russia, in Numbers

    Science.gov (United States)

    Aref'ev, A. L.; Aref'ev, M. A.

    2013-01-01

    An analysis of the main tendencies in the development of engineering and technical education in Russia during the last 100 years shows that earlier strengths have been lost, and that currently technical education in Russia is far behind modern world standards.

  11. Standard technical specifications combustion engineering plants

    International Nuclear Information System (INIS)

    1992-09-01

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS) for Combustion Engineering Plants. The improved STS wee developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. This document, Volume 1, contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Sections 3.4--3.9 of the improved STS

  12. Environmental Aspects of the Engineering Training at Technical University

    Directory of Open Access Journals (Sweden)

    V. V. Bushueva

    2015-01-01

    Full Text Available Problem relevance. The article gives a justification for a need to train professionally competent, ecologically oriented engineers capable to create new equipment taking into account the ecological characteristics. Such approach expresses a requirement coherence to develop technical systems and technologies taking into account, both technical reliability and human and environmental safety. Today, in conditions of modern industrial production it is an important point in engineer’s activity. So to train future engineers who meet these requirements new forms and methods are to be found.Objectives. To prove that involvement of creative student’s teams in training the future ecologically oriented engineers is of importance. The organisational structure and methods of activities along with the principles of revitalizing search for engineering ideas and solutions to develop environmentally safe technical systems and technologies allow us to solve more complicated problems. This is the important characteristic in activities of creative groups. The article considers a significance of the future engineer’s responsibility in terms of environment safety. It gives "Methodical advices to analyse the operational impacts of technical systems on the human and environment" to show that there is a need in development of reliable and environment-safe technical systems.Novelty of this work is a technique for the organization and forms of student creative team’s activities. It represents a revised and updated option of a technique of the creative teams working at the industrial enterprises in France. The revised technique takes into consideration both the specifics of student's audience at technical university and the environment-oriented tasks to be solved. Efficiency of search and solution of environment-oriented engineering tasks is enhanced owing to use of revitalizing methods for the creative team’s activities, which are widely used today in student

  13. Theory of Technical Systems--Educational Tool for Engineering

    Science.gov (United States)

    Eder, Wolfgang Ernst

    2016-01-01

    Hubka's theory of technical systems (TTS) is briefly outlined. It describes commonalities in all engineering devices, whatever their physical principles of action. This theory is based on a general transformation system (TrfS), which can be used to show engineering in the contexts of society, economics and historic developments. The life cycle of…

  14. Technical specification optimization program - engineered safety features

    International Nuclear Information System (INIS)

    Andre, G.R.; Jansen, R.L.

    1986-01-01

    The Westinghouse Technical Specification Program (TOP) was designed to evaluate on a quantitative basis revisions to Nuclear Power Plant Technical Specifications. The revisions are directed at simplifying plant operation, and reducing unnecessary transients, shutdowns, and manpower requirements. In conjunction with the Westinghouse Owners Group, Westinghouse initiated a program to develop a methodology to justify Technical Specification revisions; particularly revisions related to testing and maintenance requirements on plant operation for instrumentation systems. The methodology was originally developed and applied to the reactor trip features of the reactor protection system (RPS). The current study further refined the methodology and applied it to the engineered safety features of the RPS

  15. Developing and Validating the Socio-Technical Model in Ontology Engineering

    Science.gov (United States)

    Silalahi, Mesnan; Indra Sensuse, Dana; Giri Sucahyo, Yudho; Fadhilah Akmaliah, Izzah; Rahayu, Puji; Cahyaningsih, Elin

    2018-03-01

    This paper describes results from an attempt to develop a model in ontology engineering methodology and a way to validate the model. The approach to methodology in ontology engineering is from the point view of socio-technical system theory. Qualitative research synthesis is used to build the model using meta-ethnography. In order to ensure the objectivity of the measurement, inter-rater reliability method was applied using a multi-rater Fleiss Kappa. The results show the accordance of the research output with the diamond model in the socio-technical system theory by evidence of the interdependency of the four socio-technical variables namely people, technology, structure and task.

  16. Standard Technical Specifications, Combustion Engineering plants

    International Nuclear Information System (INIS)

    1992-09-01

    This NUREG contains improved Standard Technical Specifications (M) for Combustion Engineering (CE) Plants and documents the positions of the Nuclear Regulatory Commission based on the CE Owners Group's proposed STS. This document is the result of extensive technical meetings and discussions among the NRC staff, the Nuclear Steam Supply System (NSSS) Owners Groups, the NSSS vendors, and the Nuclear Management and Resources Council (NUMARC). The improved STS were developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. This document Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS

  17. Standard Technical Specifications, Combustion Engineering plants

    International Nuclear Information System (INIS)

    1992-09-01

    This NUREG contains improved Standard Technical Specifications (STS) for Combustion Engineering (CE) Plants and documents the positions of the Nuclear Regulatory Commission based on the CE Owners Group's proposed STS. This document is the result of extensive technical meetings and discussions among the NRC staff, the Nuclear Steam Supply System (NSSS) Owners Groups, the NSSS vendors, and the Nuclear Management and Resources Council (NUMARC). The improved STS were developed based on the criteria in the interim Commission Policy Statement on Technical Specification Improvements for Nuclear Power Reactors, dated February 6, 1987. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved SM. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. This document Volume 3 contains the Bases for Sections 3.4--3.9 of the improved M

  18. The fully integrated engineer combining technical ability and leadership prowess

    CERN Document Server

    Cerri, Steven T

    2016-01-01

    College teaches you to be a good engineer. But it's likely that your college engineering courses didn't have time to teach you how to effectively contribute your ideas or how to transition to management or leadership. This book provides you with those missing tools. This book addresses the differences between being proficient as a technical individual and effectively contributing to and leading a team to effectively contribute to various projects. The Fully Integrated Engineer: Combining Technical Ability and Leadership Prowess shines a light on how the habits learned in school, while contributing to individual short-term success, actually become hindrances in the modern engineering workplace if your goal is to achieve long-term success as either an engineer, a team lead, manager, or leader. The author offers specific ways to address those limiting habits, turning you into an effective team contributor and leader building toward long-term career succes . The author’s approach to retooling less-than-op...

  19. REQUIREMENT VERIFICATION AND SYSTEMS ENGINEERING TECHNICAL REVIEW (SETR) ON A COMMERCIAL DERIVATIVE AIRCRAFT (CDA) PROGRAM

    Science.gov (United States)

    2017-09-01

    VERIFICATION AND SYSTEMS ENGINEERING TECHNICAL REVIEW (SETR) ON A COMMERCIAL DERIVATIVE AIRCRAFT (CDA) PROGRAM by Theresa L. Thomas September... ENGINEERING TECHNICAL REVIEW (SETR) ON A COMMERCIAL DERIVATIVE AIRCRAFT (CDA) PROGRAM 5. FUNDING NUMBERS 6. AUTHOR(S) Theresa L. Thomas 7...CODE 13. ABSTRACT (maximum 200 words) The Naval Air Systems Command (NAVAIR) systems engineering technical review (SETR) process does not

  20. Biomedical Engineering at the Technical University of Denmark

    DEFF Research Database (Denmark)

    Jensen, Jørgen Arendt; Andersen, Ole Trier; Wilhjelm, Jens Erik

    1998-01-01

    The paper gives a brief overview of the biomedical engineering research and education at the Technical University of Denmark. An account of the research activities since the 1950?s is given, and examples of major efforts within ultrasound, biomagnetism, and neuroimaging are described. The evolution...... of the teaching activities since the late 1960?s along with an account of the recent initiatives to make a biomedical engineering profile at the university is described....

  1. Comparing the Scale of Web Subject Directories Precision in Technical-Engineering Information Retrieval

    Directory of Open Access Journals (Sweden)

    Mehrdokht Wazirpour Keshmiri

    2012-07-01

    Full Text Available The main purpose of this research was to compare the scale of web subject directories precision in information retrieval of technical-engineering science. Information gathering was documentary and webometric. Keywords of technical-engineering science were chosen at twenty different subjects from IEEE (Institute of Electrical and Electronics Engineers and engineering magazines that situated in sciencedirect site. These keywords are used at five subject directories Yahoo, Google, Infomine, Intute, Dmoz, that were web directories high-utilization. Usually first results in searching tools are connected to searching keywords. Because, first ten results was evaluated in every search. These assessments to consist of scale of precision, scale of error, scale retrieval items in technical-engineering categories to retrieval items entirely. The used criteria for determining the scale of precision that was according to high-utilization standards in different documents, to consist of presence of the keywords in title, appearance of keywords at the part of web retrieved pages, keywords adjacency, URL of page, page description and subject categories. Information analysis was according to Kruskal-Wallis Test and L.S.D fisher. Results revealed that there was meaningful difference about precision of web subject directories in information retrieval of technical-engineering science, Therefore this theory was confirmed.web subject directories ranked from point of precision as follows. Google, Yahoo, Intute, Dmoz, and Infomine. The scale of observed error at the first results was another criterion that was used for comparing web subject directories. In this research, Yahoo had minimum scale of error and Infomine had most of error. This research also compared the scale of retrieval items in all of categories web subject directories entirely to retrieval items in technical-engineering categories, results revealed that there was meaningful difference between them. And

  2. Tinkering and Technical Self-Efficacy of Engineering Students at the Community College

    Science.gov (United States)

    Baker, Dale R.; Wood, Lorelei; Corkins, James; Krause, Stephen

    2015-01-01

    Self-efficacy in engineering is important because individuals with low self-efficacy have lower levels of achievement and persistence in engineering majors. To examine self-efficacy among community college engineering students, an instrument to specifically measure two important aspects of engineering, tinkering and technical self-efficacy, was…

  3. Enhancing Non-Technical Skills by a Multidisciplinary Engineering Summer School

    Science.gov (United States)

    Larsen, Peter Gorm; Kristiansen, Erik Lasse; Bennedsen, Jens; Bjerge, Kim

    2017-01-01

    In general engineering studies focus on the technical skills in their own discipline. However, in their subsequent industrial careers, a significant portion of their time needs to be devoted to non-technical skills. In addition, in an increasingly globalised world collaboration in teams across cultures and disciplines is paramount to the creation…

  4. The IEEE guide to writing in the engineering and technical fields

    CERN Document Server

    Kmiec, David

    2017-01-01

    This book introduces students and practicing engineers to all the components of writing in the workplace. It teaches readers how considerations of audience and purpose govern the structure of their documents within particular work settings. The IEEE Guide to Writing in the Engineering and Technical Fields is broken up into two sections: "Writing in Engineering Organizations" and "What Can You Do With Writing?" The first section helps readers approach their writing in a logical and persuasive way as well as analyze their purpose for writing. The second section demonstrates how to distinguish rhetorical situations and the generic forms to inform, train, persuade, and collaborate. The emergence of the global workplace has brought with it an increasingly important role for effective technical communication. Engineers more often need to work in cross-functional teams with people in different disciplines, in different countries, and in different parts of the world. Engineers must know how to communicate in a rapid...

  5. At-Risk Learner Preference in Engineering/Technical Graphics: An Exploratory Study

    Science.gov (United States)

    Ernst, Jeremy V.

    2011-01-01

    This exploratory study investigated learner preferences of secondary Career and Technical Education (CTE) Engineering/Technical Graphics students using the VARK Questionnaire. The VARK Questionnaire is an instrument that assists in determining students' dominant preferred learning styles, whether visual, aural, reading, or kinesthetic. This study…

  6. Social engineering attacks: an augmentation of the socio-technical systems framework

    CSIR Research Space (South Africa)

    Shozi, A

    2015-03-01

    Full Text Available or organisation’s information. We analyse social engineering attacks as a Socio-technical System because it recognises the interaction between people and technology in a work environment. In the case of social engineering attacks, the social subsystem would...

  7. The influence of jet engine noise on hearing of technical staff

    Directory of Open Access Journals (Sweden)

    Wiesław Konopka

    2014-10-01

    Full Text Available Background: Due to high sound pressure levels (SPLs, noise produced by jet planes may be harmful to hearing of people working in their proximity. The aim of this study was to assess the effects of exposure to jet engine noise on technical staff hearing. Material and Methods: The study comprised 60 men, aged 24–50 years, employed in army as technical staff and exposed to jet engine noise for 6–20 years. The control group were 50 non-noise exposed males, aged 25–51 years. Exposure to noise emitted by jet engines was evaluated. Pure-tone audiometry (PTA and distortion product otoacoustic emissions (DPOAE were recorded in both groups. Results: Jet engines emitted broadband noise with spectrum dominated by components in the frequency range 315–6300 Hz (1/3-octave bands. Maximum A-weighted SPL during tests reached values of approx. 120–130 dB. Consequently, engine-servicing personnel (even in the case of a single engine test was exposed to noise (at A-weighted daily noise exposure level above 95 dB exceeding permissible levels. Averaged audiometric hearing threshold levels of technical staff were higher (≤ 17 dB HL, p < 0.001 than in the control group. Similarly, the DPOAE amplitude was lower (≤ 17 dB SPL, p < 0.01 in the noise-exposed subjects compared to the non-exposed ones. Significant reduction of DPOAE levels was mainly noted for high frequencies (3–6 kHz. Conclusions: Despite the usage of hearing protection devices, both PTA and DPOAE consistently showed poorer hearing in engine-servicing personnel vs. control group. Med Pr 2014;65(5:583–592

  8. CLASSIFICATION OF NEURAL NETWORK FOR TECHNICAL CONDITION OF TURBOFAN ENGINES BASED ON HYBRID ALGORITHM

    Directory of Open Access Journals (Sweden)

    Valentin Potapov

    2016-12-01

    Full Text Available Purpose: This work presents a method of diagnosing the technical condition of turbofan engines using hybrid neural network algorithm based on software developed for the analysis of data obtained in the aircraft life. Methods: allows the engine diagnostics with deep recognition to the structural assembly in the presence of single structural damage components of the engine running and the multifaceted damage. Results: of the optimization of neural network structure to solve the problems of evaluating technical state of the bypass turbofan engine, when used with genetic algorithms.

  9. Enhancing non-technical skills by a multidisciplinary engineering summer school

    Science.gov (United States)

    Larsen, Peter Gorm; Kristiansen, Erik Lasse; Bennedsen, Jens; Bjerge, Kim

    2017-11-01

    In general engineering studies focus on the technical skills in their own discipline. However, in their subsequent industrial careers, a significant portion of their time needs to be devoted to non-technical skills. In addition, in an increasingly globalised world collaboration in teams across cultures and disciplines is paramount to the creation of new and innovative products. In order to enhance the non-technical skills for groups of engineering students a series of innovation courses has been arranged and delivered in close collaboration with an industrial company (Bang & Olufsen). These courses have been organised as summer schools called 'Conceptual Design and Development of Innovative Products' (CD-DIP) and delivered outside the usual educational environment. In order to explore the impact of this single course, we have conducted a study among the students participating from 2007 to 2013. This has been carried out both qualitatively using interviews with selected students as well as quantitatively using a survey. The results are outstanding in demonstrating that the non-technical skills obtained in this single course have been of high value for a large portion of the students' subsequent professional life.

  10. Assessment of the Use of AutoCAD in Mechanical Engineering Technical Drawing Education

    OpenAIRE

    Akyürek, Turgut

    2018-01-01

    AutoCAD is one of the widely used software tools in engineering education. In this study, ageneral assessment of AutoCAD for the usage in the mechanical engineering technical drawing educationis made. AutoCAD is assessed in terms of the fulfilment of the requirements defined for the main twotechnical drawing courses. AutoCAD is assessed in terms of its capability in meeting the requirements ofthe technical drawing courses.

  11. Integrating Technical Communication in the Mechanical Engineering Curriculum

    Science.gov (United States)

    Norberg, Seth; Ashcraft, Timothy; van Poppel, Bret

    2017-11-01

    Technical communication is essential to engineering practice, but these skills can be challenging to teach and assess in the classroom. Instructors in the Mechanical Engineering (ME) program at the United States Military Academy are developing new learning exercises to prepare students for success in their capstone design course and beyond. In this paper we highlight the recent successes and lessons learned from two courses: junior-level Thermal-Fluid Systems and the senior-level ME Seminar. Both courses support the newly implemented West Point Writing Program (WPWP), an institutional, writing-across-the-curriculum program. The junior course incorporates four hands-on experiments, which provide an abundance of data for students to analyze, assess, and present. In the senior course the majority of the content that students present is from their ongoing capstone design projects. Between the two courses, students craft essays, lab reports, short summaries, posters, quad charts, and technical presentations. Both courses include peer evaluation, revision exercises, and timed (on demand) writing assignments. The junior course includes assignments co-authored by a group as well as an individual report. An overview of both courses' assignments with course-end feedback from the students and the faculty is provided. Strengths and weaknesses are identified and recommendations for instructors seeking to implement similar technical communications assignments in their own courses are presented.

  12. What Is "Good" Technical Communication? A Comparison of the Standards of Writing and Engineering Instructors.

    Science.gov (United States)

    Smith, Summer

    2003-01-01

    Presents the results of an empirical study comparing writing and engineering instructors' responses to students' technical writing. Indicates that the gap between engineering and writing teachers' standards for evaluating technical writing is not as wide as is generally assumed. Concludes that the differences that do emerge suggest ways that the…

  13. Standard Technical Specifications for Combustion Engineering Pressurized Water Reactors

    International Nuclear Information System (INIS)

    Vito, D.J.

    1980-12-01

    The Standard Technical Specifications for Combustion Engineering Pressurized Water Reactors (CE-STS) is a generic document prepared by the US NRC for use in the licensing process of current Combustion Engineering Pressurized Water Reactors. The CE-STS sets forth the limits, operating conditions, and other requirements applicable to nuclear reactor facility operation as set forth by Section 50.36 of 10 CFR 50 for the protection of the health and safety of the public. The document is revised periodically to reflect current licensing requirements

  14. Technical presentation: BGM Cryogenic Engineering Limited

    CERN Multimedia

    Caroline Laignel - FI Department

    2006-01-01

    13 - 14 June 2006 TECHNICAL PRESENTATION BGM Cryogenic Engineering Limited 09:00 - 18:00, 60-2-016, Main Building. Presentation on BGM: 11:00 - 12:00, 60-2-016, Main Building. BGM Cryogenic Engineering Limited manufactures assemblies, sub-assemblies and machined components for the cryogenic technology sector. The primary markets served include superconducting magnets used in the healthcare sector (eg MRI body scanners), spectroscopy and NMR equipment for numerous R & D and technology applications, high vacuum applications and particle physics research. BGM has specialist assembly capability including stainless steel and aluminium welding, vacuum testing, electromechanical assembly and metal finishing. BGM offers a ‘one stop shop'facility to satisfy any customer requirement. Through our design partner we can offer a full design and modelling service, including 3D modelling and production of 2D drawings on your own borders. We can conduct heat load and force calculations and advise on the best...

  15. A Study of Technical Engineering Peer Reviews at NASA

    Science.gov (United States)

    Chao, Lawrence P.; Tumer, Irem Y.; Bell, David G.

    2003-01-01

    This report describes the state of practices of design reviews at NASA and research into what can be done to improve peer review practices. There are many types of reviews at NASA: required and not, formalized and informal, programmatic and technical. Standing project formal reviews such as the Preliminary Design Review and Critical Design Review are a required part of every project and mission development. However, the technical, engineering peer reviews that support teams' work on such projects are informal, some times ad hoc, and inconsistent across the organization. The goal of this work is to identify best practices and lessons learned from NASA's experience, supported by academic research and methodologies to ultimately improve the process. This research has determined that the organization, composition, scope, and approach of the reviews impact their success. Failure Modes and Effects Analysis (FMEA) can identify key areas of concern before or in the reviews. Product definition tools like the Project Priority Matrix, engineering-focused Customer Value Chain Analysis (CVCA), and project or system-based Quality Function Deployment (QFD) help prioritize resources in reviews. The use of information technology and structured design methodologies can strengthen the engineering peer review process to help NASA work towards error-proofing the design process.

  16. The Electrical Engineering Curriculum at the Technical University of Denmark - Options in Microelectronics

    DEFF Research Database (Denmark)

    Bruun, Erik; Nielsen, Lars Drud

    1997-01-01

    This paper describes the modular structure of the engineering curriculum at the Technical University of Denmark. The basic requirements for an electrical engineering curriculum are presented and different possibilities for specialization in microelectronics and integrated circuit design...

  17. A technical writing programme implemented in a first-year engineering course at KU Leuven

    Science.gov (United States)

    Heylen, Christel; Vander Sloten, Jos

    2013-12-01

    Technical communication and technical writing are important skills for the daily work-life of every engineer. In the first-year engineering programme at KU Leuven, a technical writing programme is implemented within the project-based course 'Problem Solving and Engineering Design'. This paper describes a case study for implementing a writing programme based on active learning methods and situated learning in large classes. The programme consists of subsequent cycles of instructions, learning by doing and reflection on received feedback. In addition, a peer-review assignment, together with an interactive lecture using clicking devices, is incorporated within the assignments of the second semester. A checklist of desired writing abilities makes it easier to grade the large number of papers. Furthermore, this ensures that all staff involved in the evaluation process uses the same criteria to grade and for providing feedback.

  18. Technical abstracts: Mechanical engineering, 1990

    International Nuclear Information System (INIS)

    Broesius, J.Y.

    1991-01-01

    This document is a compilation of the published, unclassified abstracts produced by mechanical engineers at Lawrence Livermore National Laboratory (LLNL) during the calendar year 1990. Many abstracts summarize work completed and published in report form. These are UCRL-JC series documents, which include the full text of articles to be published in journals and of papers to be presented at meetings, and UCID reports, which are informal documents. Not all UCIDs contain abstracts: short summaries were generated when abstracts were not included. Technical Abstracts also provides descriptions of those documents assigned to the UCRL-MI (miscellaneous) category. These are generally viewgraphs or photographs presented at meetings. An author index is provided at the back of this volume for cross referencing

  19. Technological Innovation and Technical Communications: Their Place in Aerospace Engineering Curricula. A Survey of European, Japanese and US Aerospace Engineers and Scientists.

    Science.gov (United States)

    Pinelli, Thomas E.; And Others

    1991-01-01

    Reports on results from 260 aerospace engineers and scientists in United States, Europe, and Japan regarding their opinions about professional importance of technical communications; generation and utilization of technical communications; and relevant content of an undergraduate course in technical communications. The fields of cryogenics,…

  20. Effect of gear shift and engine start losses on control strategies for hybrid electric vehicles

    NARCIS (Netherlands)

    Ngo, V.; Hofman, T.; Steinbuch, M.; Serrarens, A.

    2012-01-01

    In this paper, energetic loss models in the events of shifting gear and starting engine in a parallel Hybrid Electric Vehicle equipped with an Automated Manual Transmission (AMT) will be introduced. The optimal control algorithm for the start-stop, power split and gear shift problem based on Dynamic

  1. Physical, technical and engineer concept of ultradeep nuclear geoprobes

    International Nuclear Information System (INIS)

    Vaschenko, V.; Vachev, B.; Pisarenko, T.

    2009-01-01

    This report presents information on the results of works dedicated to theoretical, physical and technical justification of contact thermal melting method of low thermal conductivity substances and to prospects of its practical realization as autonomous geoprobe for penetrating into deep Earth interior. The following problems and tasks were investigated and solved by the authors: 1) Investigation of processes of heat and mass transfer by contact melting in near-bore region due to movement of heat source of arbitrary form. 2) Development of methods and estimate of principal engineer parameters of contact thermal penetrating in low heat conducting environment. 3) Analysis of modern high-temperature materials and element base for construction of autonomous ultra deep thermoprobe. 4) Investigation of ecological consequences of possible emergency in case nuclear thermal heat source loss of sealing. 5) Mathematical problem formulation of ultra deep contact thermal penetrating by melting the environment for heat source of arbitrary form moving under gravity force and propose approach to its solution. 6) Formulation and solution of contact thermal penetration process optimization problem. 7) Development of methods of main engineering parameters of contact thermal melting of low heat conducting substances estimate. 8) Development of base of physical, engineering and technical concept of autonomous geoprobe for ultra deep penetrating into Earth interior. It is important that the results obtained may be used in engineering and constructing development of ultra deep geoprobe and also for calculation of technological apparatus and processes that use contact thermal melting of low thermal conducting materials

  2. Professional communications of Russian technical and engineering specialists: empirical analysis

    Directory of Open Access Journals (Sweden)

    R N Abramov

    2016-12-01

    Full Text Available Sociology of professions focus on the role of interpersonal and intergroup communications in the professional communities as an element of professional culture. The article considers forms and features of professional communications of Russian engineers and technicians in the context of their professional culture defined as the constellation of ideology, values, beliefs, language, and forms of activity typical for the community, which rarely becomes an object of Russian sociologists’ studies. The author shows that interpersonal professional communications on the various aspects of professional activity is an important element of professional culture. The article is based on the results of online survey of Russian engineers and expert interviews with Russian technical specialists - they were questioned on the ways of updating their professional knowledge and on the role of various channels of communication in this process. At the beginning of the article, the author provides an overview of approaches to the study of professional culture in Russia and abroad, and underlines the significant role of the Internet and the declining role of literature as a source of new knowledge for the engineering and technical staff. The results of the study also revealed an important role of informal and direct communications in the transfer of professional knowledge within the engineering community, while organizational environment has a relatively low impact on the updating of professional knowledge, which can be explained by the lack of management attention to the professional development of specialists.

  3. Technical dictionary power plant engineering. Vol. 1. 4. rev. and enlarged ed.

    International Nuclear Information System (INIS)

    1987-01-01

    This dictionary is a compilation of German and English technical terms of power plant engineering as far as power plants, turbine-generators and assembly engineering are concerned. It is the result of a joint effort by the Kraftwerk Union AG (KWU) and Utility Power Corp. (UPC). The entire content has been revised and approx. 6000 new terms have been added. The dictionary is meant to form a basis for uniform terminology on technical documents as well as correspondence between KWU, UPC and licensees. This computer aided dictionary is printed in capital/low case letters. Only nouns, terms with an article and proper names are capitalized in German. Some terms are written differently in American and British English and are marked with (US) or (GB). (orig./HP) [de

  4. Leveraging Independent Management and Chief Engineer Hierarchy: Vertically and Horizontally-Derived Technical Authority Value

    Science.gov (United States)

    Barley, Bryan; Newhouse, Marilyn

    2012-01-01

    In the development of complex spacecraft missions, project management authority is usually extended hierarchically from NASA's highest agency levels down to the implementing institution's project team level, through both the center and the program. In parallel with management authority, NASA utilizes a complementary, but independent, hierarchy of technical authority (TA) that extends from the agency level to the project, again, through both the center and the program. The chief engineers (CEs) who serve in this technical authority capacity oversee and report on the technical status and ensure sound engineering practices, controls, and management of the projects and programs. At the lowest level, implementing institutions assign project CEs to technically engage projects, lead development teams, and ensure sound technical principles, processes, and issue resolution. At the middle level, programs and centers independently use CEs to ensure the technical success of their projects and programs. At the agency level, NASA's mission directorate CEs maintain technical cognizance over every program and project in their directorate and advise directorate management on the technical, cost, schedule, and programmatic health of each. As part of this vertically-extended CE team, a program level CE manages a continually varying balance between penetration depth and breadth across his or her assigned missions. Teamwork issues and information integration become critical for management at all levels to ensure value-added use of both the synergy available between CEs at the various agency levels, and the independence of the technical authority at each organization.

  5. Teaching Technical Writing in a Lab Course in Chemical Engineering

    Science.gov (United States)

    Lombardo, Stephen J.

    2010-01-01

    Techniques are presented for improving the technical writing of chemical engineering students enrolled in an undergraduate laboratory course. The principles of writing covered are adopted from the book, Style: Lessons in Clarity and Grace, by Joseph M. Williams: General examples of writing are taken from this book and then are recast into examples…

  6. Navigating Community College Transfer in Science, Technical, Engineering, and Mathematics Fields

    Science.gov (United States)

    Packard, Becky Wai-Ling; Gagnon, Janelle L.; Senas, Arleen J.

    2012-01-01

    Given financial barriers facing community college students today, and workforce projections in science, technical, engineering, and math (STEM) fields, the costs of unnecessary delays while navigating transfer pathways are high. In this phenomenological study, we analyzed the delay experiences of 172 students (65% female) navigating community…

  7. The New Maritime Engineering Education at the Technical University of Denmark

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher; Andersen, Ingrid Marie Vincent; Nielsen, Ulrik Dam

    2014-01-01

    maritime engineering education has so far been very successful with the number of students increased by a factor of two and with very good job opportunities in the Danish maritime industry. A spin-off of this change is DTU's participation in a dual MSc degree engineering program: Nordic Master in Maritime......Until 2010, the maritime engineering education at the Technical University of Denmark (DTU) followed the rather classical naval architecture approach with the main focus on marine hydrodynamics and strength of ship structures. The number of students was rather modest and constant. However......, at that time the last major ship yard in Denmark was closing down and ship operation, together with ship design, became the main working area for the students after graduation. It was then decided to broaden the naval architecture education to a maritime engineering education taking marine logistics...

  8. Engineering Change Management Method Framework in Mechanical Engineering

    Science.gov (United States)

    Stekolschik, Alexander

    2016-11-01

    Engineering changes make an impact on different process chains in and outside the company, and lead to most error costs and time shifts. In fact, 30 to 50 per cent of development costs result from technical changes. Controlling engineering change processes can help us to avoid errors and risks, and contribute to cost optimization and a shorter time to market. This paper presents a method framework for controlling engineering changes at mechanical engineering companies. The developed classification of engineering changes and accordingly process requirements build the basis for the method framework. The developed method framework comprises two main areas: special data objects managed in different engineering IT tools and process framework. Objects from both areas are building blocks that can be selected to the overall business process based on the engineering process type and change classification. The process framework contains steps for the creation of change objects (both for overall change and for parts), change implementation, and release. Companies can select singleprocess building blocks from the framework, depending on the product development process and change impact. The developed change framework has been implemented at a division (10,000 employees) of a big German mechanical engineering company.

  9. Relationships, Variety & Synergy: The Vital Ingredients for Scholarship in Engineering Education? A Case Study

    Science.gov (United States)

    Clark, Robin; Andrews, Jane

    2014-01-01

    This paper begins with the argument that within modern-day society, engineering has shifted from being the scientific and technical mainstay of industrial, and more recently digital change to become the most vital driver of future advancement. In order to meet the inevitable challenges resulting from this role, the nature of engineering education…

  10. An algorithm for engineering regime shifts in one-dimensional dynamical systems

    Science.gov (United States)

    Tan, James P. L.

    2018-01-01

    Regime shifts are discontinuous transitions between stable attractors hosting a system. They can occur as a result of a loss of stability in an attractor as a bifurcation is approached. In this work, we consider one-dimensional dynamical systems where attractors are stable equilibrium points. Relying on critical slowing down signals related to the stability of an equilibrium point, we present an algorithm for engineering regime shifts such that a system may escape an undesirable attractor into a desirable one. We test the algorithm on synthetic data from a one-dimensional dynamical system with a multitude of stable equilibrium points and also on a model of the population dynamics of spruce budworms in a forest. The algorithm and other ideas discussed here contribute to an important part of the literature on exercising greater control over the sometimes unpredictable nature of nonlinear systems.

  11. Latinx and Caucasian Elementary School Children's Knowledge of and Interest in Engineering Activities

    Science.gov (United States)

    Ozogul, Gamze; Miller, Cindy Faith; Reisslein, Martin

    2017-01-01

    Ethnic minorities, such as Latinx people of Hispanic or Latino origin, and women earn fewer engineering degrees than Caucasians and men. With shifting population dynamics and high demands for a technically qualified workforce, it is important to achieve broad participation in the engineering workforce by all ethnicities and both genders. Previous…

  12. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 28: The technical communication practices of Russian and US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Keene, Michael L.; Flammia, Madelyn; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DoD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communication practices of Russian and U.S. aerospace engineers and scientists. Both studies had the same five objectives: first, to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communication to their professions; second, to determine the use and production of technical communication by aerospace engineers and scientists; third, to seek their views about the appropriate content of the undergraduate course in technical communication; fourth, to determine aerospace engineers' and scientists' use of libraries, technical information centers, and on-line databases; and fifth, to determine the use and importance of computer and information technology to them. A self administered questionnaire was distributed to Russian aerospace engineers and scientists at the Central Aero-Hydrodynamic Institute (TsAGI) and to their U.S. counterparts at the NASA Ames Research Center and the NASA Langley Research Center. The completion rates for the Russian and U.S. surveys were 64 and 61 percent, respectively. Responses of the Russian and U.S. participants to selected questions are presented in this paper.

  13. Reader-Centered Technical Writing

    Science.gov (United States)

    Narayanan, M.

    2012-12-01

    Technical writing is an essential part of professional communication and in recent years it has shifted from a genre-based approach. Formerly, technical writing primarily focused on generating templates of documents and sometimes it was creating or reproducing traditional forms with minor modifications and updates. Now, technical writing looks at the situations surrounding the need to write. This involves deep thinking about the goals and objectives of the project on hand. Furthermore, one observes that it is very important for any participatory process to have the full support of management. This support needs to be well understood and believed by employees. Professional writing may be very persuasive in some cases. When presented in the appropriate context, technical writing can persuade a company to improve work conditions ensuring employee safety and timely production. However, one must recognize that lot of professional writing still continues to make use of reports and instruction manuals. Normally, technical and professional writing addresses four aspects. Objective: The need for generating a given professionally written technical document and the goals the document is expected to achieve and accomplish. Clientele: The clientele who will utilize the technical document. This may include the people in the organization. This may also include "unintended readers." Customers: The population that may be affected by the content of the technical document generated. This includes the stakeholders who will be influenced. Environment: The background in which the document is created. Also, the nature of the situation that warranted the generation of the document. Swiss Psychologist Jean Piaget's view of Learning focuses on three aspects. The author likes to extend Jean Piaget's ideas to students, who are asked to prepare and submit Reader-Centered Technical Writing reports and exercises. Assimilation: Writers may benefit specifically, by assimilating a new object into

  14. Using Model-Based Systems Engineering To Provide Artifacts for NASA Project Life-Cycle and Technical Reviews

    Science.gov (United States)

    Parrott, Edith L.; Weiland, Karen J.

    2017-01-01

    The ability of systems engineers to use model-based systems engineering (MBSE) to generate self-consistent, up-to-date systems engineering products for project life-cycle and technical reviews is an important aspect for the continued and accelerated acceptance of MBSE. Currently, many review products are generated using labor-intensive, error-prone approaches based on documents, spreadsheets, and chart sets; a promised benefit of MBSE is that users will experience reductions in inconsistencies and errors. This work examines features of SysML that can be used to generate systems engineering products. Model elements, relationships, tables, and diagrams are identified for a large number of the typical systems engineering artifacts. A SysML system model can contain and generate most systems engineering products to a significant extent and this paper provides a guide on how to use MBSE to generate products for project life-cycle and technical reviews. The use of MBSE can reduce the schedule impact usually experienced for review preparation, as in many cases the review products can be auto-generated directly from the system model. These approaches are useful to systems engineers, project managers, review board members, and other key project stakeholders.

  15. ECOS: a configurable, multi-terabyte database supporting engineering and technical computing at Sizewell B

    International Nuclear Information System (INIS)

    Binns, F.; Fish, A.

    1992-01-01

    One of the three main classes of computing support systems is concerned with the technical and engineering aspects of Sizewell-B power station. These aspects are primarily concerned with engineering means to optimise plant use to maximise power output by increasing availability and efficiency. At Sizewell-B the Engineering Computer system (ECOS) will provide the necessary support facilities, and is described. ECOS is being used by the station commissioning team and for monitoring the state of some plant already in service. (Author)

  16. Computer aided training in nuclear power engineering at the Gdansk Technical University

    International Nuclear Information System (INIS)

    Marecki, J.; Duzinkiewicz, K.; Kosmowski, K.T.

    1993-01-01

    The Faculty of Electrical Engineering of the Gdansk Technical University has organized post-graduate studies in nuclear power engineering in cooperation with the Institute of Nuclear Research at Swierk since 1973. Post-graduate courses in nuclear power plant construction and design were organized twice. Between 1986 and 1990, prototype software was developed for aiding lectures, self-teaching and knowledge testing in the following fields: 1) dynamics and control of nuclear reactors; 2) simulators of nuclear power plant basic systems (reactor, steam generator, steam turbine, and synchronous generator). (Z.S.) 2 refs

  17. Standard technical specifications: Combustion engineering plants. Volume 1, Revision 1: Specifications

    International Nuclear Information System (INIS)

    1995-04-01

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Combustion Engineering Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS

  18. Proceedings of the 18th technical meeting on nuclear reactor and radiation for KURRI engineers and the 9th technical official group section 5 meeting in Kyoto University

    International Nuclear Information System (INIS)

    2010-03-01

    This report is a summary of 18th Technical Meeting on Nuclear Reactor and Radiation for KURRI Engineers in Kyoto University. This was also the 9th meeting for technical official group section 5 (nuclear and radiation) in Kyoto University. In the workshop, three special lectures held were: (1) 'On Border Between Subcritical and Supercritical', (2) 'Memories of Nuclear Power Plant Management for 40 Years', and (3) 'Introduction of Technical Office in Faculty of Engineering, Kyoto University'. The technical presentations held were: (1) 'Radiation Background Study of Specialty Products in Senshu Region', (2) 'Introduction of Radioactivation Analysis at KUR', (3) 'Consideration of Critical Approach Method for KUR Low-Enrichment Fuel Reactor Core Using SRAC', (4) 'Evaluation of Temperature Coefficient of KUR Low-Enrichment Fuel Reactor Core Using SRAC'. As training for technical staffs in Technical Office, we visited the facility in Ashiu Research Forest. An introduction of this facility and the comments from the participants were included in this report. (S.K.)

  19. An Approach to Developing Independent Learning and Non-Technical Skills Amongst Final Year Mining Engineering Students

    Science.gov (United States)

    Knobbs, C. G.; Grayson, D. J.

    2012-01-01

    There is mounting evidence to show that engineers need more than technical skills to succeed in industry. This paper describes a curriculum innovation in which so-called "soft" skills, specifically inter-personal and intra-personal skills, were integrated into a final year mining engineering course. The instructional approach was…

  20. Lowest Price, Technically Acceptable Evaluation Criteria Used in the November 2014 Request for Proposal for the Program Executive Office Soldier Systems Engineering and Technical Assistance (SETA) Contract

    Science.gov (United States)

    2017-09-01

    GS-0895-09 Industrial Engineering Technician 23.04 7.56 GS-0810-09 Civil Engineering Developmental (Programming) 23.04 7.56 GS-0810-11 Civil ... Engineering –Programming 27.88 9.14 GS-0810-12 Civil Engineering –Design 33.41 10.96 GS-2210-09 Info Tech Spec (Network Systems/Customer Support) 23.04...USED IN THE NOVEMBER 2014 REQUEST FOR PROPOSAL FOR THE PROGRAM EXECUTIVE OFFICE SOLDIER SYSTEMS ENGINEERING AND TECHNICAL ASSISTANCE (SETA) CONTRACT

  1. Internal combustion engines for alcohol motor fuels: a compilation of background technical information

    Energy Technology Data Exchange (ETDEWEB)

    Blaser, Richard

    1980-11-01

    This compilation, a draft training manual containing technical background information on internal combustion engines and alcohol motor fuel technologies, is presented in 3 parts. The first is a compilation of facts from the state of the art on internal combustion engine fuels and their characteristics and requisites and provides an overview of fuel sources, fuels technology and future projections for availability and alternatives. Part two compiles facts about alcohol chemistry, alcohol identification, production, and use, examines ethanol as spirit and as fuel, and provides an overview of modern evaluation of alcohols as motor fuels and of the characteristics of alcohol fuels. The final section compiles cross references on the handling and combustion of fuels for I.C. engines, presents basic evaluations of events leading to the use of alcohols as motor fuels, reviews current applications of alcohols as motor fuels, describes the formulation of alcohol fuels for engines and engine and fuel handling hardware modifications for using alcohol fuels, and introduces the multifuel engines concept. (LCL)

  2. Development of technical skills in Electrical Power Engineering students: A case study of Power Electronics as a Key Course

    Science.gov (United States)

    Hussain, I. S.; Azlee Hamid, Fazrena

    2017-08-01

    Technical skills are one of the attributes, an engineering student must attain by the time of graduation, as per recommended by Engineering Accreditation Council (EAC). This paper describes the development of technical skills, Programme Outcome (PO) number 5, in students taking the Bachelor of Electrical Power Engineering (BEPE) programme in Universiti Tenaga Nasional (UNITEN). Seven courses are identified to address the technical skills development. The course outcomes (CO) of the courses are designed to instill the relevant technical skills with suitable laboratory activities. Formative and summative assessments are carried out to gauge students’ acquisition of the skills. Finally, to measure the attainment of the technical skills, key course concept is used. The concept has been implemented since 2013, focusing on improvement of the programme instead of the cohort. From the PO attainment analysis method, three different levels of PO attainment can be calculated: from the programme level, down to the course and student levels. In this paper, the attainment of the courses mapped to PO5 is measured. It is shown that Power Electronics course, which is the key course for PO5, has a strong attainment at above 90%. PO5 of other six courses are also achieved. As a conclusion, by embracing outcome-based education (OBE), the BEPE programme has a sound method to develop technical psychomotor skills in the degree students.

  3. Technical problems and future underground engineering experiments

    Energy Technology Data Exchange (ETDEWEB)

    Higgins, G H [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

    1969-07-01

    The technical problems to be solved in future underground engineering experiments are of two kinds. One concerns adequate description of the variation of nuclear explosion effects with physical nd chemical properties of the explosion site. The other concerns engineering of the explosive detonation system to provide adequate safety and security, concurrently with minimum total costs per explosion. The semiempirical equations for explosion effects can be trusted only in the range of explosive energy, depth of burst, and rock type for which there is prior experience. Effects calculations based on the principles of continuum mechanics and measurable geophysical properties appear to work in the few test cases, such as Gasbuggy, to which they have been applied. These calculational methods must be tested in a variety of situations. The relevance of dynamic and static measurements on Dragon Trail, Bronco, Rulison, Stoop, Ketch, and Pinedale to proving the methods are discussed in this paper. The traditional methods of assembling and fielding nuclear explosives have evolved from practice at the Nevada Test Site. These provide great flexibility and assure maximum recovery of all data from each test, thus minimizing the time required to achieve desired results. Timing and firing, radiation monitoring, explosives assembly and emplacement, explosive performance, weather monitoring, and dynamic measurements of earth and building motion have all been handled traditionally as independent functions. To achieve lower costs in underground engineering experiments and projects, one prototype system combining all electronic, measurement, and communication functions is being built. Much further work will be required to complete this effort, including, especially, an examination of safety criteria and means for assuring operational and public safety at reduced costs. (author)

  4. Technical problems and future underground engineering experiments

    International Nuclear Information System (INIS)

    Higgins, G.H.

    1969-01-01

    The technical problems to be solved in future underground engineering experiments are of two kinds. One concerns adequate description of the variation of nuclear explosion effects with physical nd chemical properties of the explosion site. The other concerns engineering of the explosive detonation system to provide adequate safety and security, concurrently with minimum total costs per explosion. The semiempirical equations for explosion effects can be trusted only in the range of explosive energy, depth of burst, and rock type for which there is prior experience. Effects calculations based on the principles of continuum mechanics and measurable geophysical properties appear to work in the few test cases, such as Gasbuggy, to which they have been applied. These calculational methods must be tested in a variety of situations. The relevance of dynamic and static measurements on Dragon Trail, Bronco, Rulison, Stoop, Ketch, and Pinedale to proving the methods are discussed in this paper. The traditional methods of assembling and fielding nuclear explosives have evolved from practice at the Nevada Test Site. These provide great flexibility and assure maximum recovery of all data from each test, thus minimizing the time required to achieve desired results. Timing and firing, radiation monitoring, explosives assembly and emplacement, explosive performance, weather monitoring, and dynamic measurements of earth and building motion have all been handled traditionally as independent functions. To achieve lower costs in underground engineering experiments and projects, one prototype system combining all electronic, measurement, and communication functions is being built. Much further work will be required to complete this effort, including, especially, an examination of safety criteria and means for assuring operational and public safety at reduced costs. (author)

  5. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 14: An analysis of the technical communications practices reported by Israeli and US aerospace engineers and scientists

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Elazar, David; Kennedy, John M.

    1991-01-01

    As part of Phase 4 of the NASA/DoD Aerospace Knowledge Diffusion Research Project, two pilot studies were conducted that investigated the technical communications practices of Israeli and U.S. aerospace engineers and scientists. Both studies had the same five objectives: first, to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communications to their profession; second, to determine the use and production of technical communications by aerospace engineers and scientists; third, to seek their view about the appropriate content of an undergraduate course in technical communications; fourth, to determine aerospace engineers' and scientists' use of libraries, technical information centers, and on-line databases; and fifth, to determine the use and importance of computer and information technology to them. A self-administered questionnaire was mailed to randomly selected U.S. aerospace engineers and scientists who are working in cryogenics, adaptive walls, and magnetic suspension. A slightly modified version was sent to Israeli aerospace engineers and scientists working at Israel Aircraft Industries, LTD. Responses of the Israeli and U.S. aerospace engineers and scientists to selected questions are presented in this paper.

  6. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 16: A comparison of the technical communications practices of Russian and US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Kennedy, John M.; Barclay, Rebecca O.

    1993-01-01

    As part of Phase 4 of the NASA/DOD Aerospace Knowledge Diffusion Project, two studies were conducted that investigated the technical communications practices of Russian and U.S. aerospace engineers and scientists. Both studies have the same five objectives: first, to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communications to their profession; second, to determine the use and production of technical communications by aerospace engineers and scientists; third, to seek their views about the appropriate content of an undergraduate course in technical communications; fourth, to determine aerospace engineers' and scientists' use of libraries, technical information centers, and on-line data bases; and fifth, to determine the use and importance of computer and information technology to them. A self-administered questionnaire was distributed to aerospace engineers and scientists at the Central Aero-Hydrodynamic Institute (TsAGI), NASA ARC, and NASA LaRC. The completion rates for the Russian and U.S. surveys were 64 and 61 percent, respectively. The responses of the Russian and U.S. participants, to selected questions, are presented in this report.

  7. Conceptions of cognition for cognitive engineering

    DEFF Research Database (Denmark)

    Blomberg, Olle

    2011-01-01

    Cognitive processes, cognitive psychology tells us, unfold in our heads. In contrast, several approaches in cognitive engineering argue for a shift of unit of analysis from what is going on in the heads of operators to the workings of whole socio-technical systems. This shift is sometimes presented...... as part of the development of a new understanding of what cognition is and where the boundaries of cognitive systems are. Cognition, it is claimed, is not just situated or embedded, but extended and distributed in the world. My main question in this article is what the practical significance...... is of this framing of an expanded unit of analysis in a cognitive vocabulary. I focus on possible consequences for how cognitive engineering practitioners think about function allocation in system design, and on what the relative benefits and costs are of having a common framework and vocabulary for talking about...

  8. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 21: Technological innovation and technical communications: Their place in aerospace engineering curricula. A survey of European, Japanese, and US Aerospace Engineers and Scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Holland, Maurita Peterson; Keene, Michael L.; Kennedy, John M.

    1991-01-01

    Aerospace engineers and scientists from Western Europe, Japan, and the United States were surveyed as part of the NASA/DoD Aerospace Knowledge Diffusion Research Project. Questionnaires were used to solicit their opinions regarding the following: (1) the importance of technical communications to their profession; (2) the use and production of technical communications; and (3) their views about the appropriate content of an undergraduate course in technical communications. The ability to communicate technical information effectively was very important to the aerospace engineers and scientists who participated in the study. A considerable portion of their working week is devoted to using and producing technical information. The types of technical communications used and produced varied within and among the three groups. The type of technical communication product used and produced appears to be related to respondents' professional duties. Respondents from the three groups made similar recommendations regarding the principles, mechanics, and on-the-job communications to be included in an undergraduate technical communications course for aerospace majors.

  9. Technical evaluation report on the proposed amendment to the technical specifications on the reactor protection system and the engineered safety features actuation system for Ft. Calhoun, Unit No. 1

    International Nuclear Information System (INIS)

    Selan, J.C.

    1982-01-01

    This report documents the technical evaluation of the application to amend the Technical Specifications for the Ft. Calhoun Unit No. 1 Nuclear Generating Plant. The review criteria are based on the Technical Specifications of St. Lucie and Calvert Cliffs, IEEE Standards, Combustion Engineering Standard Technical Specifications, and the Code of Federal Regulations. The evaluation compares the submittal made by the licensee with the NRC staff position and the review criteria and presents the reviewer's conclusion on the acceptability of the application to amend the Technical Specifications

  10. Voltage Spectral Structure as a Parameter of System Technical Diagnostics of Ship Diesel Engine-Synchronous Generators

    Directory of Open Access Journals (Sweden)

    Gasparjans Aleksandrs

    2015-07-01

    Full Text Available A method of technical diagnostics of ship diesel engine – generator installation – is proposed. Spectral-power diagnostic parameters of the synchronous generator voltage and currents are used. The electric machine in this case is the multipurpose sensor of diagnostic parameters. A judgment on the quality of the operational processes in diesel engine cylinders and its technical condition is possible on the basis of these parameters. This method is applicable to piston compressor installations with electric drive. On the basis of such parameters as rotating torque, angular speed and angular acceleration it is possible to estimate the quality of the operating process in the cylinders of a diesel engine, the condition of its cylinder-piston group and the crank gear mechanism. The investigation was realized on the basis of a diesel-generator with linear load. The generator operation was considered for the case of constant RL load. Together with the above mentioned, the condition of bearings of synchronous machines, uniformity of the air gap, windings of the electric machine were estimated during the experiments as well. The frequency spectrum of the stator current of the generator was researched and analyzed. In this case the synchronous machine is becoming a rather exact multipurpose diagnostic sensor. The signal of non-uniformity in the operation process of diesel engine cylinders and its technical condition is the increasing of the amplitudes of typical frequencies.

  11. Socio-Technical Perspective on Interdisciplinary Interactions During the Development of Complex Engineered Systems

    Science.gov (United States)

    McGowan, Anna-Maria R.; Daly, Shanna; Baker, Wayne; Papalambros, panos; Seifert, Colleen

    2013-01-01

    This study investigates interdisciplinary interactions that take place during the research, development, and early conceptual design phases in the design of large-scale complex engineered systems (LaCES) such as aerospace vehicles. These interactions, that take place throughout a large engineering development organization, become the initial conditions of the systems engineering process that ultimately leads to the development of a viable system. This paper summarizes some of the challenges and opportunities regarding social and organizational issues that emerged from a qualitative study using ethnographic and survey data. The analysis reveals several socio-technical couplings between the engineered system and the organization that creates it. Survey respondents noted the importance of interdisciplinary interactions and their benefits to the engineered system as well as substantial challenges in interdisciplinary interactions. Noted benefits included enhanced knowledge and problem mitigation and noted obstacles centered on organizational and human dynamics. Findings suggest that addressing the social challenges may be a critical need in enabling interdisciplinary interactions

  12. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 29: A comparison of the technical communications practices of Japanese and US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1994-01-01

    As part of Phase 4 of the NASA/DoD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of Japanese and U.S. aerospace engineers and scientists. Both studies have the same seven objectives: first, to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communications to their profession; second, to determine the use and production of technical communications by aerospace engineers and scientists; third; to seek their views about the appropriate content of an undergraduate course in technical communications; fourth, to determine aerospace engineers' and scientists' use of libraries, technical information centers, and on-line data bases; fifth, to determine the use and importance of computer and information technology to them; sixth, to determine their use of electronic networks; and seventh, to determine their use of foreign and domestically produced technical reports. A self-administered questionnaire was distributed to aerospace engineers and scientists in Japan and at the NASA Ames Research Center and the NASA Langley Research Center. The completion rates for the Japanese and U.S. surveys were 85 and 61 percent, respectively. Responses of the Japanese and U.S. participants to selected questions are presented in this report.

  13. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 17: A comparison of the technical communication practices of Dutch and US aerospace engineers and scientists

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DoD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of Dutch and U.S. aerospace engineers and scientists. Both studies have the same seven objectives: first, to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communications to their profession; second, to determine the use and production of technical communications by aerospace engineers and scientists; third, to seek their views about the appropriate content of an undergraduate course in technical communications; fourth, to determine aerospace engineers' and scientists' use of libraries, technical information centers, and on-line data bases; fifth, to determine the use and importance of computer and information technology to them; sixth, to determine their use of electronic networks; and seventh, to determine their use of foreign and domestically produced technical reports. A self-administered questionnaire was distributed to aerospace engineers and scientists at the National Aerospace Laboratory (NLR), and NASA Ames Research Center, and the NASA Langley Research Center. The completion rates for the Dutch and U.S. surveys were 55 and 61 percent, respectively. Responses of the Dutch and U.S. participants to selected questions are presented.

  14. Strategy for assessing the technical, environmental, and engineering feasibility of subseabed disposal

    International Nuclear Information System (INIS)

    Anderson, D.R.; Boyer, D.G.; Herrmann, H.; Kelly, J.; Talbert, D.M.

    1980-01-01

    This paper presents the strategy and management techniques used in the development of the US Subseabed Disposal Program (SDP) for possible disposal of both high-level waste and spent fuel. These have been developed through joint efforts of the Department of Energy (DOE), Division of Waste Isolation, the Sandia Technical Program Manager, the Technical Program Coordinators, the Advisory Group, and the Principal Investigators. Three subsections of this paper address the various components which make up the SDP strategy and management techniques. The first section will summarize the US DOE high-level waste and spent fuel disposal program and the position that the SDP occupies within that program. The second section, the Subseabed Program Plan, addresses the technical and administrative tools which are employed to facilitate the day-to-day operation of the SDP. The third section addresses the current studies and future plans for addressing the legal, political, and international uncertainties that must be resolved prior to the time the SDP reaches the final engineering phases

  15. Consolidation on civil engineering and technical infrastructure

    CERN Document Server

    Alves, P; Pepinster, P; van Baaren, W; CERN. Geneva. ST Division

    2003-01-01

    The use and age of the civil engineering structure (office buildings, halls, tunnels) and of tertiary technical equipment (mainly HVAC and electricity) at CERN is such that their renovation must be considered in the near future. Due to the large number of buildings and equipment in these conditions, and the restricted budget available it is extremely important to define priorities. The aim of this paper is to give an overview of the current conditions and the related problems, based on data analysis of CERN database and confronting it with the inventory made at CERN by an external company. After having identified the most frequent problems and repairs to carry out, a planning for intervention is therefore presented optimizing the safety aspects, maintenance costs and comfort for the users. The timescale of this intervention is related to the money that will be available in the coming years.

  16. Status, Vision, and Challenges of an Intelligent Distributed Engine Control Architecture

    Science.gov (United States)

    Behbahani, Alireza; Culley, Dennis; Garg, Sanjay; Millar, Richard; Smith, Bert; Wood, Jim; Mahoney, Tim; Quinn, Ronald; Carpenter, Sheldon; Mailander, Bill; hide

    2007-01-01

    A Distributed Engine Control Working Group (DECWG) consisting of the Department of Defense (DoD), the National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) and industry has been formed to examine the current and future requirements of propulsion engine systems. The scope of this study will include an assessment of the paradigm shift from centralized engine control architecture to an architecture based on distributed control utilizing open system standards. Included will be a description of the work begun in the 1990's, which continues today, followed by the identification of the remaining technical challenges which present barriers to on-engine distributed control.

  17. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 41: Technical communication practices of Dutch and US aerospace engineers and scientists: International perspective on aerospace

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Kennedy, John M.

    1994-01-01

    As part of Phase 4 of the NASA/DOD Aerospace Knowledge Diffusion Research Project, studies were conducted that investigated the technical communications practices of Dutch and U.S. aerospace engineers and scientists. The studies had the following objectives: (1) to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communication to their professions, (2) to determine the use and production of technical communication by aerospace engineers and scientists, (3) to investigate their use of libraries and technical information centers, (4) to investigate their use of and the importance to them of computer and information technology, (5) to examine their use of electronic networks, and (6) to determine their use of foreign and domestically produced technical reports. Self-administered (mail) questionnaires were distributed to Dutch aerospace engineers and scientists at the National Aerospace Laboratory (NLR) in the Netherlands, the NASA Ames Research Center in the U.S., and the NASA Langley Research Center in the U.S. Responses of the Dutch and U.S. participants to selected questions are presented in this paper.

  18. An overview of training and technical communication of Chinese representative nuclear power engineering company of EPC mode

    International Nuclear Information System (INIS)

    Qi Ting; Zhang Xiangyu

    2015-01-01

    After the Fukushima severe accident, nuclear power development has been in stagnation in all over the world. The Chinese nuclear industry has a slowdown on new NPP construction. As a result, high level technique on safety and effective communication are required. For nuclear power engineering company with EPC mode, high quality on training and technical communication is the principal investment in order to achieve better service on engineering design, environmental impact assessment, environmental engineering design, and equipment supervision and so on. EPC mode requires wide range knowledge on almost every field related to nuclear on nuclear power engineering. In this paper, the author investigated the case of the only nuclear power engineering EPC company (CNPE) in China and present an overview on its training and technical communication both domestic and abroad. Basically, there are 4 main branches of training. The internal training focuses on specifically task (both management and technique), such as HSE training, QC training and quality and safety training. Long term education in the university is organized by cooperated mechanism. Code and platform training is partly carried out by international organization or company, and the experienced engineers coach makes up the other part. The communication is a large part since the EPC mode needs the information and requirements from the NPP entity, authority, and the other institutes, international organizations (like IAEA, NINE, IRSN, OECD, NRC and CEA etc.) and sometimes the public. The overview of the training and communication of the EPC company prevails the outline of its advantage on domestic communication and disadvantage on international technical communication. The paper can be a tool on the soft strength construction of company under EPC mode to broaden its business like consultation and training. Some advice is given by the author on the consultation and global communication in the future. (author)

  19. The Engineering Graphics Olimpiad as a Means for Students’ Creative Professional Competence Formation in the Technical Higher School

    Directory of Open Access Journals (Sweden)

    N. S. Bushmakina

    2013-01-01

    Full Text Available The paper is devoted to the creative professional competence development by the technical high school students – the prospective building engineers – by means of the Engineering Graphics Olympiad. The authors in- vestigate the concepts of the creative competences, creative abilities, creative professional competences, and denote the structure of the engineering- graphic competence. Its main components, singled out by the group expert assessment, form the basis for the Olympiad content regarding its selection and major rounds. For the more argumentative selection it is recommended to provide the pedagogic expertise corresponding with the requirements of the Federal State Educational Standards and considering the students’ level. The formation levels of the competence in question are discussed along with the corresponding knowledge and skills. The authors present the brief analysis of the research outcomes and make a conclusion about the necessity of stu- dents’ additional preparatory work regarding the specificity of the engineering graphics training in the technical higher school. 

  20. Baseball Stadium Design: Teaching Engineering Economics and Technical Communication in a Multi-Disciplinary Setting.

    Science.gov (United States)

    Dahm, Kevin; Newell, James

    2001-01-01

    Reports on a course at Rowan University, based on the economic design of a baseball stadium, that offers an introduction to multidisciplinary engineering design linked with formal training in technical communication. Addresses four pedagogical goals: (1) developing public speaking skills in a realistic, business setting; (2) giving students…

  1. SIMULATION OF CHARACTERISTICS OF DUAL-CORE PHASE SHIFTING TRANSFORMER

    Directory of Open Access Journals (Sweden)

    Kalinin L.P.

    2014-04-01

    Full Text Available The role and importance of phase shifting transformers are increased as a result of the further development of integrated power systems. This gives the rise to new technical solutions which entails the necessity of comparison of new developments with existing. The article consider the technical characteristics of dual-core phase shifting transformer which later will be used as a basis for comparison with other competing options and assess of their technical efficiency.

  2. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 18: A comparison of the technical communication practices of aerospace engineers and scientists in India and the United States

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DoD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of India and U.S. aerospace engineers and scientists. Both studies have the same seven objectives: first, to solicit the opinions of aerospace engineers and scientists regarding the importance of technical communications to their profession; second, to determine the use and production of technical communications by aerospace engineers and scientists; third, to seek their views about the appropriate content of an undergraduate course in technical communications; fourth, to determine aerospace engineers' and scientists' use of libraries, technical information centers, and on-line data bases; fifth, to determine the use and importance of computer and information technology to them; sixth, to determine their use of electronic networks; and seventh, to determine their use of foreign and domestically produced technical reports. A self-administered questionnaire was distributed to aerospace engineers and scientists at the Indian Institute of Science and the NASA Langley Research Center. The completion rates for the India and U.S. surveys were 48 and 53 percent, respectively. Responses of the India and U.S. participants to selected questions are presented in this report.

  3. Recent Experiences of the NASA Engineering and Safety Center (NESC) GN and C Technical Discipline Team (TDT)

    Science.gov (United States)

    Dennehy, Cornelius J.

    2010-01-01

    The NASA Engineering and Safety Center (NESC), initially formed in 2003, is an independently funded NASA Program whose dedicated team of technical experts provides objective engineering and safety assessments of critical, high risk projects. The GN&C Technical Discipline Team (TDT) is one of fifteen such discipline-focused teams within the NESC organization. The TDT membership is composed of GN&C specialists from across NASA and its partner organizations in other government agencies, industry, national laboratories, and universities. This paper will briefly define the vision, mission, and purpose of the NESC organization. The role of the GN&C TDT will then be described in detail along with an overview of how this team operates and engages in its objective engineering and safety assessments of critical NASA projects. This paper will then describe selected recent experiences, over the period 2007 to present, of the GN&C TDT in which they directly performed or supported a wide variety of NESC assessments and consultations.

  4. NTRCI Legacy Engine Research and Development Project Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Smith-Holbert, Connie [National Transportation Research Center, Inc., Knoxville, TN (United States); Petrolino, Joseph [National Transportation Research Center, Inc., Knoxville, TN (United States); Watkins, Bart [Power Source Technologies Inc., Corvallis, OR (United States); Irick, David [Power Source Technologies Inc., Corvallis, OR (United States)

    2011-12-31

    The Legacy engine is a completely new design, transitional diesel engine, replacing the reciprocating engine with a rotary engine. The Legacy engine offers significant advances over conventional internal combustion engines in 1) power to weight ratio; 2) multiple fuel acceptance; 3) fuel economy; and 4) environmental compliance. These advances are achieved through a combination of innovative design geometry, rotary motion, aspiration simplicity, and manufacturing/part simplicity. The key technical challenge to the Legacy engine's commercialization, and the focus of this project, was the development of a viable roton tip seal. The PST concept for the roton tip seal was developed into a manufacturable design. The design was evaluated using a custom designed and fabricated seal test fixture and further refined. This design was incorporated into the GEN2.5A prototype and tested for achievable compression pressure. The Decision Point at the end of Phase 1 of the project (described below) was to further optimize the existing tip seal design. Enhancements to the tip seal design were incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Compression pressures adequate for compression ignition of diesel fuel were achieved, although not consistently in all combustion volumes. The variation in compression pressures was characterized versus design features. As the roton tip seal performance was improved, results pointed toward inadequate performance of the housing side seals. Enhancement of the housing side seal system was accomplished using a custom designed side seal test fixture. The design enhancements developed with the test fixture were also incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Finally, to simplify the requirements for the roton tip seals and to enhance the introduction and combustion of fuel, a flush-mount fuel injector

  5. Technical feasibility assessment of oleic sunflower methyl ester utilisation in Diesel bus engines

    International Nuclear Information System (INIS)

    Silva, Fernando Neto da; Prata, Antonio Salgado; Teixeira, Jorge Rocha

    2003-01-01

    This paper describes the results obtained while testing the technical feasibility of using oleic sunflower methyl ester (SME) blended with Diesel fuel in proportions up to 30% in an unmodified Diesel bus engine. Vegetable oils methyl esters blended with Diesel oil are commonly used in compression ignition engines. However, R and D background information on the practical use of traditional sunflower oil derivatives is sparse. The present results include evaluation of the engine performance and fuel consumption and gaseous concentrations (CO and NO x ) in the exhaust gas. The exhaust gas opacity while using Diesel/SME blends and Diesel fuel was also compared. The collected data show that oleic SME utilisation did not lead to a deterioration of engine performance or to an increase in fuel consumption. Furthermore, significant increases of NO x and CO concentrations in the exhaust gas derived from SME utilisation were not detected. The smoke opacity was slightly reduced when SME was used in the proportion of 30%. The experimental testing seems to indicate that oleic SME is a suitable replacement for Diesel fuel and can be used safely in compression ignition engines in proportions as high as 30%. (Author)

  6. Technical feasibility assessment of oleic sunflower methyl ester utilisation in Diesel bus engines

    International Nuclear Information System (INIS)

    Neto da Silva, Fernando; Salgado Prata, Antonio; Rocha Teixeira, Jorge

    2003-01-01

    This paper describes the results obtained while testing the technical feasibility of using oleic sunflower methyl ester (SME) blended with Diesel fuel in proportions up to 30% in an unmodified Diesel bus engine. Vegetable oils methyl esters blended with Diesel oil are commonly used in compression ignition engines. However, R and D background information on the practical use of traditional sunflower oil derivatives is sparse. The present results include evaluation of the engine performance and fuel consumption and gaseous concentrations (CO and NO X ) in the exhaust gas. The exhaust gas opacity while using Diesel/SME blends and Diesel fuel was also compared. The collected data show that oleic SME utilisation did not lead to a deterioration of engine performance or to an increase in fuel consumption. Furthermore, significant increases of NO X and CO concentrations in the exhaust gas derived from SME utilisation were not detected. The smoke opacity was slightly reduced when SME was used in the proportion of 30%. The experimental testing seems to indicate that oleic SME is a suitable replacement for Diesel fuel and can be used safely in compression ignition engines in proportions as high as 30%

  7. Standard technical specifications for combustion engineering pressurized water reactors

    International Nuclear Information System (INIS)

    1979-08-01

    This Standard Technical Specification (STS) has been structured for the broadest possible use on Combustion Engineering plants currently being reviewed for an Operating License. Two separate and discrete containment specification sections are provided for each of the following containment types: Atmospheric and Dual. Optional specifications are provided for those features and systems which may be included in individual plant designs but are not generic in their scope of application. Alternate specifications are provided in a limited number of cases to cover situations where alternate specification requirements are necessary on a generic basis because of design differences. This revision of STS does not typically include requirements which may be added or revised as a result of the NRC staff's further review of the Three Mile Island incident

  8. Informational Reinforcement of Students’ Course Design Aimed at Promoting Engineers Training Quality in Technical Education

    Directory of Open Access Journals (Sweden)

    B. N. Guzanov

    2012-01-01

    Full Text Available Using the modern information technologies in educational process is regarded as one of the main directions in training the qualified specialists with systematic engineering thinking. The optimum combination of various educational technologies and computerized resources can improve teaching quality and promote students’ professional level. Taking as an example one of the basic technical disciplines of the engineering training curriculum at a technical higher school, the authors describe the computerized technology facilitating the course design. The technology in question - the «Reduktor» courseware - adapts the complex product of Autodesk –AutoCAD for educational purposes. The above program is the enhanced interface of AutoCAD, linked to the Microsoft Excel spreadsheet and the reference data library used for designing the reduction gear. The experimental research, based on the qualimetric approach and continuous diagnostic and prognostic monitoring of the key indices of knowledge acquisition, proves the effectiveness of informational reinforcement of students self-dependent work. 

  9. Fuzzy Determination of Target Shifting Time and Torque Control of Shifting Phase for Dry Dual Clutch Transmission

    Directory of Open Access Journals (Sweden)

    Zhiguo Zhao

    2014-01-01

    Full Text Available Based on the independently developed five-speed dry dual clutch transmission (DDCT, the paper proposes the torque coordinating control strategy between engine and two clutches, which obtains engine speed and clutch transferred torque in the shifting process, adequately reflecting the driver intention and improving the shifting quality. Five-degree-of-freedom (DOF shifting dynamics model of DDCT with single intermediate shaft is firstly established according to its physical characteristics. Then the quantitative control objectives of the shifting process are presented. The fuzzy decision of shifting time and the model-based torque coordinating control strategy are proposed and also verified by simulating under different driving intentions in up-/downshifting processes with the DCT model established on the MATLAB/Simulink. Simulation results validate that the shifting control algorithm proposed in this paper can not only meet the shifting quality requirements, but also adapt to the various shifting intentions, having a strong robustness.

  10. Formation of personnel corps of engineers in the Urals: sociological aspect

    Directory of Open Access Journals (Sweden)

    Boris Sergeevich Pavlov

    2012-03-01

    Full Text Available In terms of crisis economic development, one of priority goals for the technical institutes of higher education is to train engineers who are competitive on the regional labour markets. The main root of the problem of low prestige of the engineering profession in Russia, the slippage in the personnel training in technical universities lies in the depreciation of engineering work, and reduction of its social and economic attractiveness. The gap between science, education and industry leads to aging of engineering staff at the manufactures and to migration of the most talented engineers into other fields of activity. This paper analyzes current problems of engineers training organization in the Urals. The causes of sharp decline of the engineering profession social status in Russia, the fall of interest of secondary school graduates to continuation of their studies in technical institutes of higher education are reviewed. The authors show that the formation of engineering competence as a defining personal and vocational quality of a specialist involves actualization of the student's motivation, one's active and purposeful adaptation to the educational process, increasing one's responsibility for mastering the curriculum. Conclusions and suggestions of the authors are based on the results of a comprehensive sociological research conducted by them in 2011 in five high schools of the Urals (Yekaterinburg, Nizhnevartovsk and Chelyabinsk. The survey showed that during the stage of young specialists' preparation, cooperation in the «university - enterprise» system is actually shifted to the interaction, in fact, between institute of higher education and young professionals who act as the sellers of their labour. The authors believe that it makes sense to roll over (or rather - to stimulate the active engineering work of the most productive engineering professionals who have reached retirement age. Equally sharp and critical are the issues of

  11. Phase I Technical Report for the Engineering of Monosodium Titanate

    International Nuclear Information System (INIS)

    NASH, CHARLES

    2004-01-01

    Monosodium titanate (MST) is an inorganic adsorbent that effectively removes strontium, plutonium, uranium, and other trace elements from alkaline salt supernate. Current plans use the MST in batch contact processes to treat Savannah River Site (SRS) waste solutions that require 90Sr and actinide removal to meet low level disposal criteria. More effective use of MST may be realized if the MST could be engineered into a form suitable for a continuous treatment process such as an adsorption column. The main benefits of column operation are (1) enhanced loading due to equilibration with feed adsorbate levels versus product levels, and (2) a small footprint relative to that of a batch contact tank. The current baseline MST material features particles of nominally 0.5-35 micron in size, which are much too fine for use in an adsorption column. An extensive review of the literature and consultation with technical experts identified candidate methods to produce engineered forms of MST. From this list a review team selected five candidate methods for further study. Laboratory syntheses at Savannah River National Laboratory (SRNL) and offsite produced representative samples for characterization and performance testing. Testing identified two suitable methods. The two methods include internal gelation, which is patented technology of Oak Ridge National Laboratory, and internal hydrolysis, a method in which the MST is produced within a porous substrate. A commercial sodium titanate, SrTreat(R), produced by Fortum Engineering (Finland), demonstrated good performance as well although plutonium removal kinetics appeared much slower than observed for the other engineered MST materials

  12. Culture and Workplace Communications: A Comparison of the Technical Communications Practices of Japanese and U.S. Aerospace Engineers and Scientists.

    Science.gov (United States)

    Pinelli, Thomas E.; Sato, Yuko; Barclay, Rebecca O.; Kennedy, John M.

    1997-01-01

    Japanese (n=94) and U.S. (n=340) aerospace scientists/engineers described time spent communicating information, collaborative writing, importance of technical communication courses, and the use of libraries, computer networks, and technical reports. Japanese respondents had greater language fluency; U.S. respondents spent more time with…

  13. Recent Experiences of the NASA Engineering and Safety Center (NESC) Guidance Navigation and Control (GN and C) Technical Discipline Team (TDT)

    Science.gov (United States)

    Dennehy, Cornelius J.

    2011-01-01

    The NASA Engineering and Safety Center (NESC) is an independently funded NASA Program whose dedicated team of technical experts provides objective engineering and safety assessments of critical, high risk projects. NESC's strength is rooted in the diverse perspectives and broad knowledge base that add value to its products, affording customers a responsive, alternate path for assessing and preventing technical problems while protecting vital human and national resources. The Guidance Navigation and Control (GN&C) Technical Discipline Team (TDT) is one of fifteen such discipline-focused teams within the NESC organization. The TDT membership is composed of GN&C specialists from across NASA and its partner organizations in other government agencies, industry, national laboratories, and universities. This paper will briefly define the vision, mission, and purpose of the NESC organization. The role of the GN&C TDT will then be described in detail along with an overview of how this team operates and engages in its objective engineering and safety assessments of critical NASA.

  14. Using Model-Based System Engineering to Provide Artifacts for NASA Project Life-Cycle and Technical Reviews Presentation

    Science.gov (United States)

    Parrott, Edith L.; Weiland, Karen J.

    2017-01-01

    This is the presentation for the AIAA Space conference in September 2017. It highlights key information from Using Model-Based Systems Engineering to Provide Artifacts for NASA Project Life-cycle and Technical Reviews paper.

  15. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 36: Technical uncertainty as a correlate of information use by US industry-affiliated aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Glassman, Nanci A.; Affelder, Linda O.; Hecht, Laura M.; Kennedy, John M.; Barclay, Rebecca O.

    1994-01-01

    This paper reports the results of an exploratory study that investigated the influence of technical uncertainty on the use of information and information sources by U.S. industry-affiliated aerospace engineers and scientists in completing or solving a project, task, or problem. Data were collected through a self-administered questionnaire. Survey participants were U.S. aerospace engineers and scientists whose names appeared on the Society of Automotive Engineers (SAE) mailing list. The results support the findings of previous research and the following study assumptions. Information and information-source use differ for projects, problems, and tasks with high and low technical uncertainty. As technical uncertainty increases, information-source use changes from internal to external and from informal to formal sources. As technical uncertainty increases, so too does the use of federally funded aerospace research and development (R&D). The use of formal information sources to learn about federally funded aerospace R&D differs for projects, problems, and tasks with high and low technical uncertainty.

  16. Tissue-engineered trachea: History, problems and the future

    OpenAIRE

    Tan, Qiang; Steiner, Rudolf; Hoerstrup, Simon P.; Weder, Walter

    2017-01-01

    This review tries to summarize the efforts over the past 20 years to construct a tissue-engineered trachea. After illustrating the main technical bottlenecks faced nowadays, we discuss what might be the solutions to these bottlenecks. You may find out why the focus in this research field shifts dramatically from the construction of a tubular cartilage tissue to reepithelialization and revascularization of the prosthesis. In the end we propose a novel concept of ‘in vivo bioreactor', defined a...

  17. The Development of a Project-Based Collaborative Technical Writing Model Founded on Learner Feedback in a Tertiary Aeronautical Engineering Program

    Science.gov (United States)

    Tatzl, Dietmar; Hassler, Wolfgang; Messnarz, Bernd; Fluhr, Holger

    2012-01-01

    The present article describes and evaluates collaborative interdisciplinary group projects initiated by content lecturers and an English-as-a-Foreign-Language (EFL) instructor for the purpose of teaching technical writing skills in an aeronautical engineering degree program. The proposed technical writing model is assessed against the results of a…

  18. TECHNICAL COORDINATION

    CERN Multimedia

    A. Ball

    Overview From a technical perspective, CMS has been in “beam operation” state since 6th November. The detector is fully closed with all components operational and the magnetic field is normally at the nominal 3.8T. The UXC cavern is normally closed with the radiation veto set. Access to UXC is now only possible during downtimes of LHC. Such accesses must be carefully planned, documented and carried out in agreement with CMS Technical Coordination, Experimental Area Management, LHC programme coordination and the CCC. Material flow in and out of UXC is now strictly controlled. Access to USC remains possible at any time, although, for safety reasons, it is necessary to register with the shift crew in the control room before going down.It is obligatory for all material leaving UXC to pass through the underground buffer zone for RP scanning, database entry and appropriate labeling for traceability. Technical coordination (notably Stephane Bally and Christoph Schaefer), the shift crew and run ...

  19. Engineering Programs of Tomorrow: The Role of Agricultural Engineering.

    Science.gov (United States)

    Edwards, Donald M.

    Due to rapid growth of societal and technological endeavors, engineers of the future will require greater technical competence. At the same time, engineering will become more people oriented with greater emphasis placed on people input into decision making. As a result, engineering education must not only provide improved technical education but…

  20. The Evaluation of the Effectiveness of ESP Courses in Enhancing Technical Translation Proficiency: A Case Study of ESP Course for Mechanical Engineering Students

    Science.gov (United States)

    Hatam, Amir Hussein; Shafiei, Shilan

    2012-01-01

    The purpose of the present study was twofold. Firstly, it tried to investigate the relationship between the technical English proficiency of the students of Mechanical Engineering in the universities of Iran and their technical translation proficiency in translating technical texts of Mechanics. Secondly, it attempted to evaluate the effectiveness…

  1. Technical summary of geological, hydrological, and engineering studies at the Slick Rock Uranium Mill Tailings sites, Slick Rock, Colorado

    International Nuclear Information System (INIS)

    1990-12-01

    The purpose of this document is to provide the Colorado Department of Health (CDH) with a summary of the technical aspects of the proposed remedial action for the Slick Rock tailings near Slick Rock, Colorado. The technical issues summarized in this document are the geology and groundwater at the Burro Canyon disposal site and preliminary engineering considerations for the disposal cell

  2. Mechanical Engineering Practice – using a simple Stirling engine as case

    DEFF Research Database (Denmark)

    Meyer, Knud Erik

    2011-01-01

    The first technical course that students in mechanical engineering take at the Technical University of Denmark is called “Mechanical Engineering Practice”. We have used a simple Stirling engine as a design-implement project. Students were asked to design and build a heat engine using materials....... The Stirling engine worked well in the drawing assignments. The Stirling engine also served as illustration of coming courses in mechanical engineering. The resulting engines had large variations in their design and most groups succeeded in building a functioning engine. However, achieved efficiencies were...... obtained by their own means and were competing on achieving the highest efficiency. We added an extra dimension to the project by making detailed measurements of the pressure variation to check simple thermodynamic models of the engine. The course had integrated lessons in sketching and technical drawing...

  3. A Comparison of the Technical Communications Practices of Japanese and U.S. Aerospace Engineers and Scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Holloway, Karen; Sato, Yuko; Barclay, Rebecca O.; Kennedy, John M.

    1996-01-01

    To understand the diffusion of aerospace knowledge, it is necessary to understand the communications practices and the information-seeking behaviors of those involved in the production, transfer, and use of aerospace knowledge at the individual, organizational, national, and international levels. In this paper, we report selected results from a survey of Japanese and U.S. aerospace engineers and scientists that focused on communications practices and information-seeking behaviors in the workplace. Data are presented for the following topics: importance of and time spent communicating information, collaborative writing, need for an undergraduate course in technical communications, use of libraries, the use and importance of electronic (computer) networks, and the use and importance of foreign and domestically produced technical reports. The responses of the survey respondents are placed within the context of the Japanese culture. We assume that differences in Japanese and U.S. cultures influence the communications practices and information-seeking behaviors of Japanese and U.S. aerospace engineers and scientists.

  4. A Study to Determine the Basic Science and Mathematics Topics Most Needed by Engineering Technology Graduates of Wake Technical Institute in Performing Job Duties.

    Science.gov (United States)

    Edwards, Timothy I.; Roberson, Clarence E., Jr.

    A survey of 470 graduates of the six engineering technology programs at Wake Technical Institute--Architectural, Chemical, Civil Engineering, Computer, Electronic Engineering, and Industrial Engineering Technologies--and 227 of their employers was conducted in October, 1979, to determine the science and mathematics topics most needed by…

  5. Technical communications in aerospace - An analysis of the practices reported by U.S. and European aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.; Glassman, Myron

    1990-01-01

    The flow of scientific and technical information (STI) at the individual, organizational, national, and international levels is studied. The responses of U.S and European aerospace engineers and scientists to questionnaires concerning technical communications in aerospace are examined. Particular attention is given to the means used to communicate information and the social system of the aerospace knowledge diffusion process. Demographic data about the survey respondents are provided. The methods used to communicate technical data and the sources utilized to solve technical problems are described. The importance of technical writing skills and the use of computer technology in the aerospace field are discussed. The derived data are useful for R&D and information managers in order to improve access to and utilization of aerospace STI.

  6. Possibilities of Monitoring the Technical Condition of the Combustion Engine with Starter Load Current

    Directory of Open Access Journals (Sweden)

    Michal Jukl

    2014-01-01

    Full Text Available This article deals with the verification of relations between the electric current of engine starter and tightness of the combustion chamber and the possibility of its use for the evaluation of the state in terms of engine wear. Engine wear is closely related to the quality of fuel combustion and also with the amount of produced harmful emissions. On this basis, it would be possible to extend the technical requirements of the protocol OBD to include the indirect control of engine wear. To meet the objectives set out above measurement was carried out by a petrol engine, which was located in the vehicle Škoda Felicia Combi GLX 1.3 The whole measurement was divided into several parts. The first measurement was carried out on the abovementioned motor without simulating leakage. The second measurement was performed when the leakage of one cylinder was simulated. Simulated leakage was conducted at removing the spark plugs. Other measurements simulated “mild” leak of the whole engine – all cylinders. Leakage was implemented by loosing all the spark plugs about 8 turns against full tightening with the appropriate torque. The last, fourth measurement simulates a “large” leaks of engine cylinders. This leakage was induced by removing all the spark plugs from all cylinders. As the measurement results showed leakage of one cylinder, and also the whole engine is reflected not only in the individual amplitude of the starter current, but also the shape of the entire curve.

  7. Experience in isotope leak-proof control of engineering objects - technical and economical aspects

    International Nuclear Information System (INIS)

    Kras, J.; Walis, L.; Myczkowski, S.

    2002-01-01

    One of the basic uses of the tracer methods for commercial purposes is the leak-proof control and determination of location of possible leakages in engineering objects. The works in this area - development of methods and equipment, and its practical use - are being conducted at the Institute of Nuclear Chemistry and Technology in Warsaw. The paper presents the division of engineering objects according to their suitability for leak proof testing with tracer methods, alternative traditional methods, sensitivity levels and the technical effects achieved with both method groups, plus the attempts to determine the economical effects of the tracer method. The introduction to the paper describes the method of field preparation of gaseous radioactive tracer, i.e. methyl bromide CH 3 Br labelled with bromine 82 Br isotope. (author)

  8. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 33: Technical communications practices and the use of information technologies as reported by Dutch and US aerospace engineers

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Tan, Axel S. T.; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DOD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of Dutch and U.S. aerospace engineers and scientists. A self-administered questionnaire was distributed to aerospace engineers and scientists at the National Aerospace Laboratory (The Netherlands), and NASA ARC (U.S.), and NASA LaRC (U.S.). This paper presents responses of the Dutch and U.S. participants to selected questions concerning four of the seven project objectives: determining the importance of technical communications to aerospace engineering professionals, investigating the production of technical communications, examining the use and importance of computer and information technology, and exploring the use of electronic networks.

  9. A New Paradigm for Chemical Engineering?

    DEFF Research Database (Denmark)

    Gani, Rafiqul

    evidence of this change comes from the jobs taken by graduating chemical engineering professionals in North America, Europe, and some of the Asian countries. In terms of where the graduating chemical engineers are going to work, a clear shift from the commodity chemical industry to the product oriented...... businesses has been observed. There is an increasing trend within the chemical industry to focus on products and the sustainable processes that can make them. Do these changes point to a paradigm shift in chemical engineering as a discipline? Historically, two previous paradigm shifts in chemical engineering...... corresponded to major shifts in chemical engineering as a discipline, which affected not only the education of chemical engineers, but also the development of chemical engineering as a discipline. Has the time come for a new paradigm shift that will prepare the current and future chemical engineering graduates...

  10. 2003 Chemical Engineering Division annual technical report

    International Nuclear Information System (INIS)

    Lewis, D.; Graziano, D.; Miller, J. F.; Vandegrift, G.

    2004-01-01

    The Chemical Engineering Division is one of six divisions within the Engineering Research Directorate at Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, to promote national security, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. The Division is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Additionally, the Division operates the Analytical Chemistry Laboratory, which provides a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training in chemistry; physics; materials science; and electrical, mechanical, chemical, and nuclear engineering. They are specialists in electrochemistry, ceramics, metallurgy, catalysis, materials characterization, nuclear magnetic resonance, repository science, and the nuclear fuel cycle. Our staff have experience working in and collaborating with university, industry and government research and development laboratories throughout the world. Our wide-ranging expertise finds ready application in solving energy, national security, and environmental problems. Division personnel are frequently called on by governmental and industrial organizations for advice and contributions to problem solving in areas that intersect present and past Division programs and activities. Currently, we are engaged in the development of several technologies of

  11. Welding engineering manual for constructing engineers. Pt. 2

    International Nuclear Information System (INIS)

    Neumann, A.

    1986-01-01

    The manual is a real treasure trove of knowledge and experience for the statics expert, the constructing engineer, and the welding engineer, who have to do with design and dimensioning of welding engineering work for steel structures, bridges, boilers, vessels, and pipes. Many practical examples are given together with numerous data that provide helpful information for the task of technical and economic design and dimensioning. Determination of efficient and appropriate cross-sectional dimensions and materials is the main goal of the manual. Structural steel engineering and installations subject to monitoring and inspection such as boilers, pipings, pressure vessels, and nuclear installations are the subject fields dealt with in separate chapters. The dimensioning rules presented are based on the regulations and technical codes valid in the GDR and the FRG. The catalogue of technical rules of the FRG concerning structural steel engineering and installations as above are given in supplementary chapters. (orig./HP) [de

  12. [Integration of fundamental and applied medical and technical research made at the department of the biomedical systems, Moscow State Institute of Electronic Engineering].

    Science.gov (United States)

    Selishchev, S V

    2004-01-01

    The integration results of fundamental and applied medical-and-technical research made at the chair of biomedical systems, Moscow state institute of electronic engineering (technical university--MSIEE), are described in the paper. The chair is guided in its research activity by the traditions of higher education in Russia in the field of biomedical electronics and biomedical engineering. Its activities are based on the extrapolation of methods of electronic tools, computer technologies, physics, biology and medicine with due respect being paid to the requirements of practical medicine and to topical issues of research and design.

  13. The Impact of Ict on Business Models for Delivery Of ConsultancyServices - The Case Of Technical Engineering

    DEFF Research Database (Denmark)

    Falch, Morten; Nicolajsen, Hanne Westh

    2009-01-01

    This paper analyses the impact of the use of ICT in production and delivery of technical engineering consultancy services on business structures with regard to industry convergence and transaction costs. The paper takes an empirical study on the introduction of 3D-modelling tools in the building...... section in a Scandinavian engineering consultancy firm as its point of departure. The discussion identifies three different structural aspects, which all are affected by the use of ICT: Internationalisation vs. Local markets, Outsourcing vs. Structural integration, and Division of work between actors...

  14. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 17: The relationship between seven variables and the use of US government technical reports by US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.; Glassman, Nanci; Demerath, Loren

    1991-01-01

    A study was undertaken to investigate the relationship between the use of U.S. government technical reports by U.S. aerospace engineers and scientists and seven selected sociometric variables. Data were collected by means of a self-administered mail survey which was distributed to a randomly drawn sample of American Institute of Aeronautics and Astronautics (AIAA) members. Two research questions concerning the use of conference meeting papers, journal articles, in-house technical reports, and U.S. government technical reports were investigated. Relevance, technical quality, and accessibility were found to be more important determinants of the overall extent to which U.S. government technical reports and three other information products were used by U.S. aerospace engineers and scientists.

  15. NASA/DoD Aerospace Knowledge Diffusion Research Project. XXXIII - Technical communications practices and the use of information technologies as reported by Dutch and U.S. aerospace engineers

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Tan, Axel S. T.; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DOD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of Dutch and U.S. aerospace engineers and scientists. A self-administered questionnaire was distributed to aerospace engineers and scientists at the National Aerospace Laboratory (The Netherlands), and NASA Ames Research Center (U.S.), and the NASA Langley Research Center (U.S.). This paper presents responses of the Dutch and U.S. participants to selected questions about four of the seven project objectives: determining the importance of technical communications to aerospace engineering professionals, investigating the production of technical communications, examining the use and importance of computer and information technology, and exploring the use of electronic networks.

  16. Standard technical specifications: Combustion engineering plants. Volume 3, Revision 1: Bases (Sections 3.4--3.9)

    International Nuclear Information System (INIS)

    1995-04-01

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Combustion Engineering Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS

  17. The Uncontrolled Economic Engine of the Developing Economies, Speeding up the Climate Shift

    Science.gov (United States)

    Khan, K. M.; Khan, M. A.

    2014-12-01

    As we progress into the 21st century, the world faces challenges of truly global nature bearing implications on the whole world in one way or another. The global economic engine has shifted from the western world (Developed Economies) to the eastern world (Developing Economies) which has brought about tremendous change in the climate related variables in this part of the world. As uncontrolled carbon emissions grow in the developing economies, the phenomenon of global warming and climate shifts become more and more prevalent. While this economic activity provides income for millions of households, it is contributing generously to the rapid degradation of the environment. Developing economies as it has been seen do not employ or abide by stringent regulations regarding emissions which result in uncontrolled emissions. In this particular scenario, it is a tedious task to convince governments in the developing economies to implement regulations regarding emissions because businesses in these economies deem such regulations to be economically unviable. The other side of the problem is that these uncontrolled emission are causing evident climate shifts which has had adverse impacts on the agricultural societies where shifting climates are leading to reduced agricultural output and productivity. Consequently the lives of millions associated directly or indirectly with agriculture are affected and on a more global level, the agricultural produce is decreasing which increases the chances of famine in parts of the world. The situation could have devastating impacts on the global economy and environmental standards and therefore needs to be addressed on emergency basis. The first step towards betterment could be the introduction of the carbon trading economy in the developing economies which would incentivize emission reduction and become more attractive and in the process sustaining minimum possible damage to the environment. Though carbon trading is a formidable first step

  18. Systems Engineering Awareness

    Science.gov (United States)

    Lucero, John

    2016-01-01

    The presentation will provide an overview of the fundamentals and principles of Systems Engineering (SE). This includes understanding the processes that are used to assist the engineer in a successful design, build and implementation of solutions. The context of this presentation will be to describe the involvement of SE throughout the life-cycle of a project from cradle to grave. Due to the ever growing number of complex technical problems facing our world, a Systems Engineering approach is desirable for many reasons. The interdisciplinary technical structure of current systems, technical processes representing System Design, Technical Management and Product Realization are instrumental in the development and integration of new technologies into mainstream applications. This tutorial will demonstrate the application of SE tools to these types of problems..

  19. Imagining Technicities

    DEFF Research Database (Denmark)

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

  20. Achieving excellence on shift through teamwork

    International Nuclear Information System (INIS)

    Newman, L.

    1988-01-01

    Anyone familiar with the nuclear industry realizes the importance of operators. Operators can achieve error-free plant operations, i.e., excellence on shift through teamwork. As a shift supervisor (senior reactor operator/shift technical advisor) the author went through the plant's first cycle of operations with no scrams and no equipment damaged by operator error, having since changed roles (and companies) to one of assessing plant operations. This change has provided the opportunity to see objectively the importance of operators working together and of the team building and teamwork that contribute to the shift's success. This paper uses examples to show the effectiveness of working together and outlines steps for building a group of operators into a team

  1. Technical issues related to NUREG 0800, Chapter 18: Human Factors Engineering/Standard Review Plan

    International Nuclear Information System (INIS)

    Savage, J.W.

    1982-01-01

    The revision of Chapter 18 of NUREG 0800, Human Factors Engineering Standard Review Plan (SRP) will be based on SECY 82-111 and guidance contained in NUREG 0700, NUREG 0801 and NUREG 0835, plus other references. In conducting field reviews of control rooms, the NRC has identified technical issues which can be used to enhance the development of the revised version of NUREG 0800, and to establish priorities among the list of possible Branch Technical Positions (BTP) in NUREG 0800, Rev. 0, Table 18.0-2. This report is a compilation of comments and suggestions from the people who used NUREG 0700 in the Control Room field reviews. This information was used to establish possible BTP topic priorities so that the most important BTPs could be issued first. The comments and suggestions are included for HFEB review in conjunction with the table of priorities

  2. Re-Engineering Vocational and Technical Education (VTE) for Sustainable Development in North Central Geo-Political Zone, Nigeria

    Science.gov (United States)

    Sofoluwe, Abayomi Olumade

    2013-01-01

    The purpose of the study is to re-engineer vocational and technical education for sustainable development in the North Central Geo-Political Zone in Nigeria. The research design adopted was a survey inferential type. Stratified random was used to select 36 schools out of 98 schools while 920 students out of 3680 students were sampled. The data…

  3. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 24: The technical communications practices of US aerospace engineers and scientists: Results of the phase 1 SAE mail survey

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1994-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of U.S. aerospace engineers and scientists affiliated with the Society of Automotive Engineers (SAE).

  4. Design mentoring tool : [technical summary].

    Science.gov (United States)

    2011-01-01

    In 2004 a design engineer on-line mentoring tool was developed and implemented The purpose of the tool was to assist senior engineers mentoring new engineers to the INDOT design process and improve their technical competency. This approach saves seni...

  5. Technical Writing Tips

    Science.gov (United States)

    Kennedy, Patrick M.

    2004-01-01

    The main reason engineers, technicians, and programmers write poor technical documents is because they have had little training or experience in that area. This article addresses some of the basics that students can use to master technical writing tasks. The article covers the most common problems writers make and offers suggestions for improving…

  6. Staffing, overtime, and shift scheduling project

    International Nuclear Information System (INIS)

    Lewis, P.M.

    1989-01-01

    Recent events at the Peach Bottom nuclear power plant have demonstrated the need to establish a quantifiable basis for assessing the safety significance of long work hours on nuclear power plant operators. The incidents at TMI-2, Chernobyl, and Bhopal, which all occurred during the late evening/night shift, further highlight the importance of the relationship between shift scheduling and performance. The objective of this project is to estimate, using statistical analysis on data from the nuclear industry, the effects on safety of staffing levels, overtime, and shift scheduling for operators and maintenance personnel. Regarding staffing levels, the Nuclear Regulatory Commission (NRC) currently has no explicit regulation concerning the minimum acceptable levels of staffing in a plant that has an operating license. The NRC has no systematic method for collecting data on the number of licensed operators on the operating crews. In 1982 the NRC recommended that plants write into their technical specifications a model policy on overtime. Currently, 77 nuclear power plant units have the model policy or a modification of it written into their technical specifications; 33 units have no policy on overtime. The model policy sets limits on overtime for safety related personnel, although these limits can be exceeded with plant manger approval. The US nuclear power industry has three types of shift schedules: (1) forward-rotating 8-hour/day shift schedules, (2) backward-rotating 8-hour/day schedules, and (3) 12-hour/day schedules

  7. What Philanthropy's Paradigm Shift Means for Higher Ed Fundraising

    Science.gov (United States)

    McCully, George

    2015-01-01

    This is an unprecedented era of human history, in which simultaneous transformations of every technically advanced field are being driven by the powerful technological revolution in information and communications. Technically, these transformative changes are "paradigm shifts"--a distinct kind of historical change in which the governing…

  8. Would Engineers Need Non-technical Skills or Non-technical Competences or Both?

    Directory of Open Access Journals (Sweden)

    Velli Parts

    2013-04-01

    Full Text Available Normal 0 21 MicrosoftInternetExplorer4 Two main competence approaches are under the discussion. There is evidence that graduates do not fully perceive and/or underestimate the influence of non-technical competences on their employability. An understanding of the necessity of non-technical competences develops after a graduate has already been hired and is working at that job.

  9. Improving of technical characteristics of launch vehicles with liquid rocket engines using active onboard de-orbiting systems

    Science.gov (United States)

    Trushlyakov, V.; Shatrov, Ya.

    2017-09-01

    In this paper, the analysis of technical requirements (TR) for the development of modern space launch vehicles (LV) with main liquid rocket engines (LRE) is fulfilled in relation to the anthropogenic impact decreasing. Factual technical characteristics on the example of a promising type of rocket ;Soyuz-2.1.v.; are analyzed. Meeting the TR in relation to anthropogenic impact decrease based on the conventional design approach and the content of the onboard system does not prove to be efficient and leads to depreciation of the initial technical characteristics obtained at the first design stage if these requirements are not included. In this concern, it is shown that the implementation of additional active onboard de-orbiting system (AODS) of worked-off stages (WS) into the onboard LV stages systems allows to meet the TR related to the LV environmental characteristics, including fire-explosion safety. In some cases, the orbital payload mass increases.

  10. Performance-based service acquisition (PBSA) of TRIDENT strategic weapons systems (SWS) technical engineering support (TES) services

    OpenAIRE

    Arcidiacono, William J.

    2003-01-01

    CIVINS (Civilian Institutions) Thesis document Approved for public release ; distribution is unlimited The objective of this thesis is to determine whether the Strategic Systems Programs (SSP) should apply the concepts of Performance-Based Service Acquisition (PBSA) to Strategic Weapons Systems (SWS) Technical Engineering Support (TES) Services. This thesis provides a Department of Defense (DoD), Department of the Navy (DON), and SSP SWS program acquisition and PBSA history background, ...

  11. Energy efficiency improvement by gear shifting optimization

    Directory of Open Access Journals (Sweden)

    Blagojevic Ivan A.

    2013-01-01

    Full Text Available Many studies have proved that elements of driver’s behavior related to gear selection have considerable influence on the fuel consumption. Optimal gear shifting is a complex task, especially for inexperienced drivers. This paper presents an implemented idea for gear shifting optimization with the aim of fuel consumption minimization with more efficient engine working regimes. Optimized gear shifting enables the best possible relation between vehicle motion regimes and engine working regimes. New theoretical-experimental approach has been developed using On-Board Diagnostic technology which so far has not been used for this purpose. The matrix of driving modes according to which tests were performed is obtained and special data acquisition system and analysis process have been developed. Functional relations between experimental test modes and adequate engine working parameters have been obtained and all necessary operations have been conducted to enable their use as inputs for the designed algorithm. The created Model has been tested in real exploitation conditions on passenger car with Otto fuel injection engine and On-Board Diagnostic connection without any changes on it. The conducted tests have shown that the presented Model has significantly positive effects on fuel consumption which is an important ecological aspect. Further development and testing of the Model allows implementation in wide range of motor vehicles with various types of internal combustion engines.

  12. Manual of engineering drawing technical product specification and documentation to British and international standards

    CERN Document Server

    Simmons, Colin H; Simmons, Colin

    2012-01-01

    Manual of Engineering Drawing is a comprehensive guide for experts and novices for producing engineering drawings and annotated 3D models that meet the recent BSI and ISO standards of technical product documentation and specifications. This fourth edition of the text has been updated in line with recent standard revisions and amendments. The book has been prepared for international use, and includes a comprehensive discussion of the fundamental differences between the ISO and ASME standards, as well as recent updates regarding legal components, such as copyright, patents, and other legal considerations. The text is applicable to CAD and manual drawing, and it covers the recent developments in 3D annotation and surface texture specifications. Its scope also covers the concepts of pictorial and orthographic projections, geometrical, dimensional and surface tolerancing, and the principle of duality. The text also presents numerous examples of hydraulic and electrical diagrams, applications, bearings, adhesives, ...

  13. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 37: The impact of political control on technical communications: A comparative study of Russian and US aerospace engineers and scientists

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Flammia, Madelyn; Kennedy, John M.

    1994-01-01

    Until the recent dissolution of the Soviet Union, the Communist Party exerted a strict control of access to and dissemination of scientific and technical information (STI). This article presents models of the Soviet-style information society and the Western-style information society and discusses the effects of centralized governmental control of information on Russian technical communication practices. The effects of political control on technical communication are then used to interpret the results of a survey of Russian and U.S. aerospace engineers and scientists concerning the time devoted to technical communication, their collaborative writing practices and their attitudes toward collaboration, the kinds of technical documents they produce and use, and their use of computer technology, and their use of and the importance to them of libraries and technical information centers. The data are discussed in terms of tentative conclusions drawn from the literature. Finally, we conclude with four questions concerning government policy, collaboration, and the flow of STI between Russian and U.S. aerospace engineers and scientists.

  14. Forensic geotechnical engineering

    CERN Document Server

    Babu, GL

    2016-01-01

    In this edited volume on advances in forensic geotechnical engineering, a number of technical contributions by experts and professionals in this area are included. The work is the outcome of deliberations at various conferences in the area conducted by Prof. G.L. Sivakumar Babu and Dr. V.V.S. Rao as secretary and Chairman of Technical Committee on Forensic Geotechnical Engineering of International Society for Soil Mechanics and Foundation Engineering (ISSMGE). This volume contains papers on topics such as guidelines, evidence/data collection, distress characterization, use of diagnostic tests (laboratory and field tests), back analysis, failure hypothesis formulation, role of instrumentation and sensor-based technologies, risk analysis, technical shortcomings. This volume will prove useful to researchers and practitioners alike.

  15. How Engineers Perceive the Importance of Ethics in Finland

    Science.gov (United States)

    Taajamaa, Ville; Majanoja, Anne-Maarit; Bairaktarova, Diana; Airola, Antti; Pahikkala, Tapio; Sutinen, Erkki

    2018-01-01

    Success in complex and holistic engineering practices requires more than problem-solving abilities and technical competencies. Engineering education must offer proficient technical competences and also train engineers to think and act ethically. A technical "engineering-like" focus and demand have made educators and students overlook the…

  16. EXPLORING THE PROBLEMS FACED BY TECHNICAL SCHOOL STUDENTS IN LEARNING ENGINEERING COURSES

    Directory of Open Access Journals (Sweden)

    RAMLEE MUSTAPHA

    2014-12-01

    Full Text Available The teaching of engineering courses is relatively challenging due to the nature of the courses that are perceived as “difficult courses” by a number of students. Thus, the purpose of this action research was to explore the problems faced by electrical and electronic engineering (PKEE students studying a difficult topic–transistor. This research was also aimed at identifying the students’ attitude towards Problem-based Learning (PBL. Literature has shown that PBL could enhance students’ understanding and make the learning more meaningful. The theoretical framework of this study was based on Kemmis and Mc Taggart model. Cooperative learning method was also utilised in this study consisted of Jigsaw technique in the first and second rounds of the study. In the final round, the discussion method was used. In an action research design, a classroom is a usual research site. Thus, an engineering class of 30 Form 5 students in a Technical School was selected. The PBL method was applied in the class for a nine-week duration. Empirical data were gathered from peer assessment, observation, and pre- and post-tests. The data were described descriptively using frequency, mean and standard deviation. The main results show that the students were more interactive and their post-test result shows significant increases. In terms of the attitude towards PBL, the participants rated PBL highly. The participants also assert that the main benefits of PBL include enhancing their collaborative and problem-solving skills.

  17. Automatic generation of natural language nursing shift summaries in neonatal intensive care: BT-Nurse.

    Science.gov (United States)

    Hunter, James; Freer, Yvonne; Gatt, Albert; Reiter, Ehud; Sripada, Somayajulu; Sykes, Cindy

    2012-11-01

    Our objective was to determine whether and how a computer system could automatically generate helpful natural language nursing shift summaries solely from an electronic patient record system, in a neonatal intensive care unit (NICU). A system was developed which automatically generates partial NICU shift summaries (for the respiratory and cardiovascular systems), using data-to-text technology. It was evaluated for 2 months in the NICU at the Royal Infirmary of Edinburgh, under supervision. In an on-ward evaluation, a substantial majority of the summaries was found by outgoing and incoming nurses to be understandable (90%), and a majority was found to be accurate (70%), and helpful (59%). The evaluation also served to identify some outstanding issues, especially with regard to extra content the nurses wanted to see in the computer-generated summaries. It is technically possible automatically to generate limited natural language NICU shift summaries from an electronic patient record. However, it proved difficult to handle electronic data that was intended primarily for display to the medical staff, and considerable engineering effort would be required to create a deployable system from our proof-of-concept software. Copyright © 2012 Elsevier B.V. All rights reserved.

  18. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 31: The technical communications practices of US aerospace engineers and scientists: Results of the phase 1 SME mail survey

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1994-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical communications practices of U.S. aerospace engineers and scientists affiliated with, not necessarily belonging to, the Society of Manufacturing Engineers (SME).

  19. MODELS OF PROJECT REVERSE ENGINEERING

    Directory of Open Access Journals (Sweden)

    Віктор Володимирович ІВАНОВ

    2017-03-01

    Full Text Available Reverse engineering decided important scientific and technical problems of increasing the cost of the existing technical product by transforming it into a product with other features or design. Search ideas of the new application of existing products on the base of heuristic analysis were created. The concept of reverse engineering and its division into three types: conceptual, aggregate and complete was expanded. The use of heuristic methods for reverse engineering concept was showed. The modification model of Reverse engineering based on the model of РМВОК was developed. Our model includes two new phases: identification and transformation. At the identification phase, technical control is made. At the transformation phase, search heuristic idea of the new applied existing technical product was made. The model of execution phase that included heuristic methods, metrological equipment, and CAD/CAM/CAE program complex was created. The model that connected economic indicators of reverse engineering project was developed.

  20. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 45; The Technical Communications Practices of US Aerospace Engineers and Scientists: Results of the Phase 3 US Aerospace Engineering Educators Survey

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1996-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. Little is also known about the intermediary-based system that is used to transfer the results of federally funded R&D to the U.S. aerospace industry. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports, present a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communication practices of U.S. aerospace engineers and scientists who were members of the American Institute of Aeronautics and Astronautics (AIAA) and identified themselves as educators.

  1. Technical universities beyond marketization: Educating the virtuous engineer

    NARCIS (Netherlands)

    Reijers, Wessel Hubert Maria

    2015-01-01

    In this paper, I argue that marketization trends affecting universities in general are strongly present in the management and education of technical universities. Partly, this is due to the historical background of the technical university as such, but marketization can nonetheless negatively affect

  2. [NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 1:] The value of Scientific and Technical Information (STI), its relationship to Research and Development (R&D), and its use by US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Glassman, Myron; Barclay, Rebecca O.; Oliu, Walter E.

    1990-01-01

    The relationship between scientific and technical information (STI), its use by aerospace engineers and scientists, and the aerospace R&D process is examined. Data are presented from studies of the role of STI in the performance and management of R&D activities and the behavior of engineers when using and seeking information. Consideration is given to the information sources used to solve technical problems, the production and use of technical communications, and the use of libraries, technical information centers, and on-line data bases.

  3. Interactive Lab to Learn Radio Astronomy, Microwave & Antenna Engineering at the Technical University of Cartagena (Spain

    Directory of Open Access Journals (Sweden)

    Fernando Daniel Quesada-Pereira

    2011-02-01

    Full Text Available An initiative carried out at the Technical University of Cartagena (UPCT, Spain to encourage students and promote the interest for Scientific and Engineering Culture between society is presented in this contribution. For this purpose, a long-term project based on the set-up of an interactive laboratory surrounding a small Radio Telescope (SRT system has been carried out. The main novelty is that this project is entirely being developed by students of last courses of our Telecommunication Engineering Faculty, under the supervision of four lecturers. This lab offers the possibility to remotely control the SRT, and it provides a set of multimedia web-based applications to produce a novel, practical, multidisciplinary virtual laboratory to improve the learning and teaching processes in related sciences and technologies.

  4. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 56: Technical Communications in Engineering and Science: The Practices Within a Government Defense Laboratory

    Science.gov (United States)

    VonSeggern, Marilyn; Jourdain, Janet M.; Pinelli, Thomas E.

    1996-01-01

    Research in recent decades has identified the varied information needs of engineers versus scientists. While most of that research looked at the differences among organizations, we surveyed engineers and scientists within a single Air Force research and development laboratory about their information gathering, usage, and production practices. The results of the Phillips Laboratory survey confirm prior assumptions about distinctions between engineering and science. Because military employees responded at a much higher rate than civilian staff, the survey also became an opportunity to profile a little-known segment of the engineer/scientist population. In addition to the effect Phillips Laboratory's stated mission may have on member engineers and scientists, other factors causing variations in technical communication and information-related activities are identified.

  5. Final Technical Report; NUCLEAR ENGINEERING RECRUITMENT EFFORT

    Energy Technology Data Exchange (ETDEWEB)

    Kerrick, Sharon S.; Vincent, Charles D.

    2007-07-02

    This report provides the summary of a project whose purpose was to support the costs of developing a nuclear engineering awareness program, an instruction program for teachers to integrate lessons on nuclear science and technology into their existing curricula, and web sites for the exchange of nuclear engineering career information and classroom materials. The specific objectives of the program were as follows: OBJECTIVE 1: INCREASE AWARENESS AND INTEREST OF NUCLEAR ENGINEERING; OBJECTIVE 2: INSTRUCT TEACHERS ON NUCLEAR TOPICS; OBJECTIVE 3: NUCLEAR EDUCATION PROGRAMS WEB-SITE; OBJECTIVE 4: SUPPORT TO UNIVERSITY/INDUSTRY MATCHING GRANTS AND REACTOR SHARING; OBJECTIVE 5: PILOT PROJECT; OBJECTIVE 6: NUCLEAR ENGINEERING ENROLLMENT SURVEY AT UNIVERSITIES

  6. The development of an e-learning software, ''Technical ethics''

    International Nuclear Information System (INIS)

    Matsue, Kazuki; Madarame, Haruki; Okamoto, Koji

    2004-01-01

    For the engineers and researchers, it is coming to the time when they are asked not only technical progress but also their ethics view. In this study, I aim to develop of the education software ''Technical Ethics'', which cultivates ethics view of the engineers. (author)

  7. Integrated risk - healthy technical conscience

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, P. [Institute of Nuclear Power Operations, Atlanta, GA (United States)

    2015-07-01

    The personal obligation leaders and individuals internalize and exercise to ensure plant operation, maintenance, and engineering activities are conducted in a manner consistent with plant design, emergency response strategies, technical requirements and that preserve operating, design and safety margins. Technical errors are increasing, both in number and significance. Causes are common at many utilities. The majority of these engineering human performance weaknesses have not had immediate impact on station reliability and safety (not self-revealing). In some recent projects, the same weaknesses affected a station's viability.

  8. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Monday 9 February 2004 From 10:00 to 12:00 - IT Auditorium - bldg. 31, 3rd floor ANSOFT High-Frequency Seminar David Prestaux, Application Engineer, ANSOFT F-78535 BUC, France This Technical Training seminar will present two Ansoft application products: Ansoft HFSS and Ansoft Designer. Ansoft HFSS makes use of the Finite Element Method (FEM) to calculate field solutions from first principles. It can accurately predict all high-frequency behaviours such as dispersion, mode conversion, and losses due to materials and radiation. Ansoft Designer is a suite of design tools to fully integrate high-frequency, physics-based electromagnetic simulations into a seamless system-level simulation environment. Ansoft Designer uses a simple interface to give complete control over every design task, by a method allowing multiple solvers, Solver on Demand. • Introduction • Overview of the Ansoft Total solution • Ansoft HFSS 9...

  9. Getting Personal: Individuality, Innovation, and Technical Communication.

    Science.gov (United States)

    Steiner, Carol J.

    1999-01-01

    Suggests that effective communication between technical and nontechnical people is difficult because technical communication lacks a personal dimension: technical people give up their identity to be considered competent. Argues that a different approach to communication education for scientists, engineers, and technologists is required to equip…

  10. The National Technical Association: A Hallmark for Access and Success

    Science.gov (United States)

    Jearld, A., Jr.

    2017-12-01

    Minority Technical Organizations (MTO) are under-utilized as a valuable resource that can help develop the next generation of scientists and engineers. For over 90 years, the National Technical Association (NTA) (www.ntaonline.org) has been the premiere technical association for scientists, engineers, architects, technologist, educators, and technical business entrepreneurs for people of color, offering professional development, mentoring and awards recognition to technical professionals. NTA and its partners are developing a diverse workforce by emphasizing enhanced access opportunities to skills development for youth among underrepresented STEM populations. Established in 1925 by Charles Summer Duke, the first African American to receive an engineering degree from Harvard University, NTA served as the model organization for more than 40 other minority technical organizations that began forming in the 1970's. NTA has served as consultants to the US government on the status of African Americans in science and engineering. The first technical organization to establish community based technical mentoring programs targeting minorities, NTA shares information and assists institutions in identifying minority talent. Members developed the first science and engineering curriculum at Historically Black Colleges and Universities (HBCU's), and are working to produce more students with geoscience degrees to ensure greater career placement with increased minority participation in the geosciences. NTA addresses the lack of access, support, and the need for networking through the longest running annual conference for technical practitioners of color. A hallmark of NTA has been access and success through inter-organizational collaborations with communities of scholars, highly experienced professionals and students to discuss the definition of what is successful geoscience education, research, and employment.

  11. Engineering Sustainability: A Technical Approach to Sustainability

    OpenAIRE

    Rosen, Marc A.

    2012-01-01

    Sustainability is a critically important goal for human activity and development. Sustainability in the area of engineering is of great importance to any plans for overall sustainability given 1) the pervasiveness of engineering activities in societies, 2) their importance in economic development and living standards, and 3) the significant impacts that engineering processes and systems have had, and continue to have, on the environment. Many factors that need to be considered and appropriate...

  12. Applied engineering fundamentals: The transition from novice to engineering manager

    International Nuclear Information System (INIS)

    Murawski, M.N.; Tomchin, E.M.

    1992-01-01

    This paper describes the development and implementation of Applied Engineering Fundamentals, a course designed for newly graduated engineers and scientists serving as technical interns within the US Department of Energy (DOE). As specialists with varying undergraduate and graduate degrees, interns need further training to prepare them for the multidisciplinary environments they will encounter as they become engineering managers. This course is designed to build on individuals strengths in diverse engineering and scientific disciplines, provide instruction in less familiar disciplines, and develop skills in integrating multiple disciplines to solve real-world problems related to nuclear facilities. The course balances systems thinking with state-of-the-art approaches to curriculum development to provide training in technical content and to foster development of professional skills

  13. Transforming Systems Engineering through Model Centric Engineering

    Science.gov (United States)

    2017-08-08

    Contract No. HQ0034-13-D-0004 Report No. SERC-2017-TR-110 Date: August 8, 2017 Transforming Systems Engineering through Model-Centric... Engineering Technical Report SERC-2017-TR-110 Update: August 8, 2017 Principal Investigator: Mark Blackburn, Stevens Institute of Technology Co...Evangelista Sponsor: U.S. Army Armament Research, Development and Engineering Center (ARDEC), Office of the Deputy Assistant Secretary of Defense for

  14. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 27: The technical communication practices of engineering and science students: Results of the phase 3 academic surveys

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Hecht, Laura M.; Kennedy, John M.

    1994-01-01

    This report describes similarities and differences between undergraduate and graduate engineering science students in the context of two general aspects of the educational experience. First, we explore the extent to which students differ regarding the factors that lead to the choice of becoming an engineer or a scientist, current satisfaction with that choice, and career-related goals and objectives. Second, we look at the technical communication practices, habits, and training of engineers and science (Physics) students. The reported data were obtained from a survey of students enrolled in the College of Engineering at the University of Illinois at Urbana-Champaign, Bowling Green State University, and Texas A&M University. The survey was undertaken as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. Data are reported for the following categories: student demographics; skill importance, skill training, and skill helpfulness; collaborative writing; computer and information technology use and importance, use of electronic networks; use and importance of libraries and library services; use and importance of information sources and products; use of foreign technical reports; and foreign language (reading and speaking) skills.

  15. Investigation and technical reviews of the long term stability and corrosion resistance of engineering barriers

    International Nuclear Information System (INIS)

    Tachikawa, Hirokazu

    2004-03-01

    The Japan Nuclear Fuel Cycle Development Institute submitted 'Second Progress Report on Research and Development for the Geological Disposal of HLW in Japan' to the Japanese government. This report contains investigations of the long term behavior of alteration of bentonite, and of the corrosion life time of overpack on the basis of experimental data and past research, assuming the ranging geological environment of Japan. However some subjects, such as the behavior of the bentonite and overpack under high pH conditions and the behavior of the engineering barrier with change of near-field environmental condition with time for promoting reliability have still been left. To take into account these conditions, expert committees composed of clay science and metal corrosion science experts were established in the Nuclear Safety Research Association and past research outcomes and the theory of safety assessment were investigated and technically reviewed from the view points of long term stability and corrosion resistance of engineering buffer materials. (author)

  16. Evaluation of Technical Feasibility of Homogeneous Charge Compression Ignition (HCCI) Engine Fueled with Hydrogen, Natural Gas, and DME

    Energy Technology Data Exchange (ETDEWEB)

    Pratapas, John; Mather, Daniel; Kozlovsky, Anton

    2013-03-31

    The objective of the proposed project was to confirm the feasibility of using blends of hydrogen and natural gas to improve the performance, efficiency, controllability and emissions of a homogeneous charge compression ignition (HCCI) engine. The project team utilized both engine simulation and laboratory testing to evaluate and optimize how blends of hydrogen and natural gas fuel might improve control of HCCI combustion. GTI utilized a state-of-the art single-cylinder engine test platform for the experimental work in the project. The testing was designed to evaluate the feasibility of extending the limits of HCCI engine performance (i.e., stable combustion, high efficiency and low emissions) on natural gas by using blends of natural gas and hydrogen. Early in the project Ricardo provided technical support to GTI as we applied their engine performance simulation program, WAVE, to our HCCI research engine. Modeling support was later provided by Digital Engines, LLC to use their proprietary model to predict peak pressures and temperatures for varying operating parameters included in the Design of Experiments test plan. Digital Engines also provided testing support for the hydrogen and natural gas blends. Prof. David Foster of University of Wisconsin-Madison participated early in the project by providing technical guidance on HCCI engine test plans and modeling requirements. The main purpose of the testing was to quantify the effects of hydrogen addition to natural gas HCCI. Directly comparing straight natural gas with the hydrogen enhanced test points is difficult due to the complexity of HCCI combustion. With the same air flow rate and lambda, the hydrogen enriched fuel mass flow rate is lower than the straight natural gas mass flow rate. However, the energy flow rate is higher for the hydrogen enriched fuel due to hydrogen’s significantly greater lower heating value, 120 mJ/kg for hydrogen compared to 45 mJ/kg for natural gas. With these caveats in mind, an

  17. How to be an Effective Technical Writer?

    Directory of Open Access Journals (Sweden)

    M Solaiman Ali

    2012-07-01

    Full Text Available Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations. Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical writing for engineers stresses that a successful engineering career requires strong writing skills. Part 2 (How to write the major sections or elements of a report describes the techniques of writing the abstract, introduction, literature review, procedure/methods & materials, results, discussion, conclusion, and recommendations. Part 3 (Special features of technical writing brings into focus some of the special features of technical writing such as tables & graphs in the text, graphics in instructions, team writing, ethics (plagiarism, document sources, three citation styles and IEEE reference style. Part 4 (Technical usage deals with writing abbreviations, initialisms and acronyms, numbers, units of measurement, and equations.Part 5 (Technical style highlights the imperative writing style and other features of technical writing such as the use of active and passive voices, plain vs. complex syntax, avoiding redundant or superfluous expressions, and vague generalities, using words or expressions with visual impact, the past tense to describe experimental work, the present tense to describe hypotheses, principles, theories and truths, and breaking up the text of the report into short sections. Part 6 (Document specifications emphasizes the technical writer’s need to conform to such document specifications as word count, format, font, number of words per line of text imposed. Part 7 (Reader-friendly technical writing suggests choosing the varied writing modes

  18. Independent technical review, handbook

    International Nuclear Information System (INIS)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project

  19. Independent technical review, handbook

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction, and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project.

  20. A broadcast engineering tutorial for non-engineers

    CERN Document Server

    Pizzi, Skip

    2014-01-01

    A Broadcast Engineering Tutorial for Non-Engineers is the leading publication on the basics of broadcast technology. Whether you are new to the industry or do not have an engineering background, this book will give you a comprehensive primer of television, radio, and digital media relating to broadcast-it is your guide to understanding the technical world of radio and television broadcast engineering. It covers all the important topics such as DTV, IBOC, HD, standards, video servers, editing, electronic newsrooms, and more.

  1. DOE handbook: Guide to good practices for the selection, training, and qualification of shift supervisors

    International Nuclear Information System (INIS)

    1999-04-01

    This Department of Energy (DOE) handbook is approved for use by all DOE Components and their contractors. The Handbook incorporates editorial changes to DOE-STD-1061-93, ''Guide to Good Practices for the Selection, Training, and Qualification of shift Supervisors,'' and supersedes DOE-STD-1061-93. Technical content of this Handbook has not changed from the original technical standard. Changes are primarily editorial improvements, redesignation of the standard to a Handbook, and format changes to conform with current Technical Standards Program procedures. This guide, used in conjunction with a facility-specific job analysis, provides a framework for the selection, training, qualification, and professional development of reactor facility and non-reactor nuclear facility shift supervisors. Training and qualification programs based on this guide should provide assurance that shift supervisors perform their jobs safely and competently

  2. DOE handbook: Guide to good practices for the selection, training, and qualification of shift supervisors

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-04-01

    This Department of Energy (DOE) handbook is approved for use by all DOE Components and their contractors. The Handbook incorporates editorial changes to DOE-STD-1061-93, ``Guide to Good Practices for the Selection, Training, and Qualification of shift Supervisors,`` and supersedes DOE-STD-1061-93. Technical content of this Handbook has not changed from the original technical standard. Changes are primarily editorial improvements, redesignation of the standard to a Handbook, and format changes to conform with current Technical Standards Program procedures. This guide, used in conjunction with a facility-specific job analysis, provides a framework for the selection, training, qualification, and professional development of reactor facility and non-reactor nuclear facility shift supervisors. Training and qualification programs based on this guide should provide assurance that shift supervisors perform their jobs safely and competently.

  3. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 15: Technical uncertainty and project complexity as correlates of information use by US industry-affiliated aerospace engineers and scientists: Results of an exploratory investigation

    Science.gov (United States)

    Pinelli, Thomas E.; Glassman, Nanci A.; Affelder, Linda O.; Hecht, Laura M.; Kennedy, John M.; Barclay, Rebecca O.

    1993-01-01

    An exploratory study was conducted that investigated the influence of technical uncertainty and project complexity on information use by U.S. industry-affiliated aerospace engineers and scientists. The study utilized survey research in the form of a self-administered mail questionnaire. U.S. aerospace engineers and scientists on the Society of Automotive Engineers (SAE) mailing list served as the study population. The adjusted response rate was 67 percent. The survey instrument is appendix C to this report. Statistically significant relationships were found to exist between technical uncertainty, project complexity, and information use. Statistically significant relationships were found to exist between technical uncertainty, project complexity, and the use of federally funded aerospace R&D. The results of this investigation are relevant to researchers investigating information-seeking behavior of aerospace engineers. They are also relevant to R&D managers and policy planners concerned with transferring the results of federally funded aerospace R&D to the U.S. aerospace industry.

  4. Transforming Systems Engineering through Model-Centric Engineering

    Science.gov (United States)

    2018-02-28

    Contract No. HQ0034-13-D-0004 Research Tasks: 48, 118, 141, 157, 170 Report No. SERC-2018-TR-103 Transforming Systems Engineering through...Model-Centric Engineering Technical Report SERC-2018-TR-103 February 28, 2018 Principal Investigator Dr. Mark Blackburn, Stevens Institute of...Systems Engineering Research Center This material is based upon work supported, in whole or in part, by the U.S. Department of Defense through the

  5. Active learning in the space engineering education at Technical University of Madrid

    Science.gov (United States)

    Rodríguez, Jacobo; Laverón-Simavilla, Ana; Lapuerta, Victoria; Ezquerro Navarro, Jose Miguel; Cordero-Gracia, Marta

    This work describes the innovative activities performed in the field of space education at the Technical University of Madrid (UPM), in collaboration with the center engaged by the European Space Agency (ESA) in Spain to support the operations for scientific experiments on board the International Space Station (E-USOC). These activities have been integrated along the last academic year of the Aerospatiale Engineering degree. A laboratory has been created, where the students have to validate and integrate the subsystems of a microsatellite by using demonstrator satellites. With the acquired skills, the students participate in a training process centered on Project Based Learning, where the students work in groups to perform the conceptual design of a space mission, being each student responsible for the design of a subsystem of the satellite and another one responsible of the mission design. In parallel, the students perform a training using a ground station, installed at the E-USOC building, which allow them to learn how to communicate with satellites, how to download telemetry and how to process the data. This also allows students to learn how the E-USOC works. Two surveys have been conducted to evaluate the impact of these techniques in the student engineering skills and to know the degree of satisfaction of students with respect to the use of these learning methodologies.

  6. Project Based Learning experiences in the space engineering education at Technical University of Madrid

    Science.gov (United States)

    Rodríguez, Jacobo; Laverón-Simavilla, Ana; del Cura, Juan M.; Ezquerro, José M.; Lapuerta, Victoria; Cordero-Gracia, Marta

    2015-10-01

    This work describes the innovation activities performed in the field of space education since the academic year 2009/10 at the Technical University of Madrid (UPM), in collaboration with the Spanish User Support and Operations Center (E-USOC), the center assigned by the European Space Agency (ESA) in Spain to support the operations of scientific experiments on board the International Space Station. These activities have been integrated within the last year of the UPM Aerospace Engineering degree. A laboratory has been created, where students have to validate and integrate the subsystems of a microsatellite using demonstrator satellites. In parallel, the students participate in a Project Based Learning (PBL) training process in which they work in groups to develop the conceptual design of a space mission. One student in each group takes the role of project manager, another one is responsible for the mission design and the rest are each responsible for the design of one of the satellite subsystems. A ground station has also been set up with the help of students developing their final thesis, which will allow future students to perform training sessions and learn how to communicate with satellites, how to receive telemetry and how to process the data. Several surveys have been conducted along two academic years to evaluate the impact of these techniques in engineering learning. The surveys evaluate the acquisition of specific and generic competences, as well as the students' degree of satisfaction with respect to the use of these learning methodologies. The results of the surveys and the perception of the lecturers show that PBL encourages students' motivation and improves their results. They not only acquire better technical training, but also improve their transversal skills. It is also pointed out that this methodology requires more dedication from lecturers than traditional methods.

  7. KEK Engineering Department -activity report FY 2003

    International Nuclear Information System (INIS)

    2005-03-01

    This report includes all kinds of activities of the Engineering Department of KEK from 2002 to 2003 FY. There are fourteen chapters, which contain KEK Prize for engineering, KEK meeting of engineering technologies, Engineering Seminar, COACK (Component Oriented Advanced Control Kernel) for cooperation R and D project, Forum on engineering technologies from 1998 to 2003 FY, Engineering Department Symposium, service trainings, Engineering Department research study, English training, training for professional worker, training for technical expert, report on joint training for technical expert, training for middle school students, and the Engineering Department system and the main events from 1971 to 2003. (S.Y. )

  8. Three Mile Island accident technical support

    International Nuclear Information System (INIS)

    Long, R.L.; Crimmins, T.M.; Lowe, W.W.

    1981-01-01

    A large number of technical support personnel were required to respond to the Three Mile Island Unit 2 (TMI-2) accident of March 28, 1979. Under the leadership of General Public Utilities personnel, onsite (round-the-clock shift) technical support began the evening of March 29 and within a week the TMI Recovery Organization incorporated all of the essential technical capability to implement the Base Plan for Cooldown, manage the radioactive waste problem, and begin the steps toward long-range plant recovery. These steps toward recovery are described in some detail. 1 refs

  9. Education of 'nuclear' students (BSc and MSc curricula) at the Faculty of Nuclear Science and Physical Engineering, Czech Technical University in Prague

    International Nuclear Information System (INIS)

    Matejka, K.; Zeman, J.

    2003-01-01

    The Faculty of Nuclear Science and Physical Engineering, Czech Technical University in Prague has been educating nuclear power engineering experts for nearly half a century. The article describes the current status and prospects of education of new specialists at the faculty for all nuclear power-related areas within the MSc and BSc level curricula. The current transition to 'European type' structured education, enabling students who have graduated from the BSc programme to continue smoothly their MSc programme, is outlined. The major courses of the 'Nuclear Engineering' educational specialisation, focused on nuclear power, environment, and dosimetry, are highlighted, including the number of lessons taught in each study year. (author)

  10. Technical considerations for the development of an engineering safety features control system with PLC

    International Nuclear Information System (INIS)

    Lee, C. K.; Kim, C. H.; Han, J. B.; Kim, H.; Lee, S. S.

    2002-01-01

    Technical considerations are summarized for the development of an ESFCS(Engineered Safety Features Control System) with PLC (Programmable Logic Controller). The ESFCS is required for the mitigation of plant accident conditions and therefore developed in conformance with the design requirements applied to the safety critical system. The design of ESFCS primarily considered its safety, and the system has an architecture that will be able to minimize spurious actuation. The PLC based functional distribution and redundant design features are adopted, and the fieldbus is applied in the communication of information and control signals between PLC processors. It is expected that the ESFCS will have several advanced design features compared with the conventional systems supplied by foreign vendors

  11. Teaching ethics to engineers: ethical decision making parallels the engineering design process.

    Science.gov (United States)

    Bero, Bridget; Kuhlman, Alana

    2011-09-01

    In order to fulfill ABET requirements, Northern Arizona University's Civil and Environmental engineering programs incorporate professional ethics in several of its engineering courses. This paper discusses an ethics module in a 3rd year engineering design course that focuses on the design process and technical writing. Engineering students early in their student careers generally possess good black/white critical thinking skills on technical issues. Engineering design is the first time students are exposed to "grey" or multiple possible solution technical problems. To identify and solve these problems, the engineering design process is used. Ethical problems are also "grey" problems and present similar challenges to students. Students need a practical tool for solving these ethical problems. The step-wise engineering design process was used as a model to demonstrate a similar process for ethical situations. The ethical decision making process of Martin and Schinzinger was adapted for parallelism to the design process and presented to students as a step-wise technique for identification of the pertinent ethical issues, relevant moral theories, possible outcomes and a final decision. Students had greatest difficulty identifying the broader, global issues presented in an ethical situation, but by the end of the module, were better able to not only identify the broader issues, but also to more comprehensively assess specific issues, generate solutions and a desired response to the issue.

  12. Works Technical Department progress report, March 1961

    Energy Technology Data Exchange (ETDEWEB)

    None

    1961-04-19

    This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  13. Fostering Creative Engineers: A Key to Face the Complexity of Engineering Practice

    Science.gov (United States)

    Zhou, Chunfang

    2012-01-01

    Recent studies have argued a shift of thinking about engineering practice from a linear conception to a system understanding. The complexity of engineering practice has been thought of as the root of challenges for engineers. Moreover, creativity has been emphasised as one key capability that engineering students should master. This paper aims to…

  14. NASA/DoD Aerospace Knowledge Diffusion Research Project: Report 43: The Technical Communication Practices of U.S. Aerospace Engineers and Scientists: Results of the Phase 1 Mail Survey -- Manufacturing and Production Perspective

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1996-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communication practices of U.S. aerospace engineers and scientists who were members of the Society of Manufacturing Engineers.

  15. How to be an Effective Technical Writer?

    OpenAIRE

    M Solaiman Ali; Dheya Al-Othmany

    2012-01-01

    Abstract--This paper has focused on technical writing as a skill for engineers. It has sought to define technical writing and throw light on the content and technique of writing the various components of successful technical reports (for example, articles, papers, or research reports, such as theses and dissertations). Then, it has highlighted other special features and principles of effective technical writing. The material in this paper is divided into seven major parts. Part 1 (Technical w...

  16. 7 CFR 1780.54 - Technical services.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 12 2010-01-01 2010-01-01 false Technical services. 1780.54 Section 1780.54 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF..., Constructing and Inspections § 1780.54 Technical services. Owners are responsible for providing the engineering...

  17. Progress report [of] Technical Physics and Prototype Engineering Division, April 1982 - March 1984

    International Nuclear Information System (INIS)

    Ramamurthi, S.S.; Chaudhry, Ramesh

    1985-01-01

    The work done by the Technical Physics and Prototype Engineering Division of the Bhabha Atomic Research Centre (BARC) at Bombay during the period from April 1982 to March 1984 is described in the form of summaries. The main thrust of the work of the Division is towards designing, developing, fabricating and if needed, producing on a large scale various instruments, equipment and components required for the programmes of the BARC and the Department of Atomic Energy. The summaries describing the work are grouped under the headings:(1) vacuum, (2) surface analysis, (3) mass spectrometry, (4) electronics, (5) cryogenics, (6) crystals and detectors, (7) glass technology and devices, and (8) optoelectronics. A list of publications of the staff-members of the Division during the report period is given. (M.G.B.)

  18. Technical Assistance Contractor management plan. Revision 1

    International Nuclear Information System (INIS)

    1995-08-01

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) as the prime contractor and three teaming partner subcontractors: Roy F. Weston, Inc. (RFW), AGRA Earth and Environmental, Inc. (AGRA), and Geraghty and Miller, Inc. (G and M). The TAC contract's scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both Surface and Ground Water Projects. The TAC team supports the DOE in completing surface remedial action and initiating ground water remediation work for start-up, characterization, compliance planning, design, construction oversight, and remedial operations. The TAC provides the DOE UMTRA Project Team with a dedicated management, scientific, and technical resource base in Albuquerque, New Mexico, which is supplemented by corporate resources. A carefully developed and maintained staff of technical experts is available to assess, analyze, develop, and execute cost-effective solutions to the demanding technical and institutional problems presented by the UMTRA Project

  19. Sequence homolog-based molecular engineering for shifting the enzymatic pH optimum

    Directory of Open Access Journals (Sweden)

    Fuqiang Ma

    2016-09-01

    Full Text Available Cell-free synthetic biology system organizes multiple enzymes (parts from different sources to implement unnatural catalytic functions. Highly adaption between the catalytic parts is crucial for building up efficient artificial biosynthetic systems. Protein engineering is a powerful technology to tailor various enzymatic properties including catalytic efficiency, substrate specificity, temperature adaptation and even achieve new catalytic functions. However, altering enzymatic pH optimum still remains a challenging task. In this study, we proposed a novel sequence homolog-based protein engineering strategy for shifting the enzymatic pH optimum based on statistical analyses of sequence-function relationship data of enzyme family. By two statistical procedures, artificial neural networks (ANNs and least absolute shrinkage and selection operator (Lasso, five amino acids in GH11 xylanase family were identified to be related to the evolution of enzymatic pH optimum. Site-directed mutagenesis of a thermophilic xylanase from Caldicellulosiruptor bescii revealed that four out of five mutations could alter the enzymatic pH optima toward acidic condition without compromising the catalytic activity and thermostability. Combination of the positive mutants resulted in the best mutant M31 that decreased its pH optimum for 1.5 units and showed increased catalytic activity at pH < 5.0 compared to the wild-type enzyme. Structure analysis revealed that all the mutations are distant from the active center, which may be difficult to be identified by conventional rational design strategy. Interestingly, the four mutation sites are clustered at a certain region of the enzyme, suggesting a potential “hot zone” for regulating the pH optima of xylanases. This study provides an efficient method of modulating enzymatic pH optima based on statistical sequence analyses, which can facilitate the design and optimization of suitable catalytic parts for the construction

  20. Evaluation of Technical Feasibility of Homogeneous Charge Compression Ignition (HCCI) Engine Fueled with Hydrogen, Natural Gas, and DME

    Energy Technology Data Exchange (ETDEWEB)

    John Pratapas; Daniel Mather; Anton Kozlovsky

    2007-03-31

    The objective of the proposed project was to confirm the feasibility of using blends of hydrogen and natural gas to improve the performance, efficiency, controllability and emissions of a homogeneous charge compression ignition (HCCI) engine. The project team utilized both engine simulation and laboratory testing to evaluate and optimize how blends of hydrogen and natural gas fuel might improve control of HCCI combustion. GTI utilized a state-of-the art single-cylinder engine test platform for the experimental work in the project. The testing was designed to evaluate the feasibility of extending the limits of HCCI engine performance (i.e., stable combustion, high efficiency and low emissions) on natural gas by using blends of natural gas and hydrogen. Early in the project Ricardo provided technical support to GTI as we applied their engine performance simulation program, WAVE, to our HCCI research engine. Modeling support was later provided by Digital Engines, LLC to use their proprietary model to predict peak pressures and temperatures for varying operating parameters included in the Design of Experiments test plan. Digital Engines also provided testing support for the hydrogen and natural gas blends. Prof. David Foster of University of Wisconsin-Madison participated early in the project by providing technical guidance on HCCI engine test plans and modeling requirements. The main purpose of the testing was to quantify the effects of hydrogen addition to natural gas HCCI. Directly comparing straight natural gas with the hydrogen enhanced test points is difficult due to the complexity of HCCI combustion. With the same air flow rate and lambda, the hydrogen enriched fuel mass flow rate is lower than the straight natural gas mass flow rate. However, the energy flow rate is higher for the hydrogen enriched fuel due to hydrogen's significantly greater lower heating value, 120 mJ/kg for hydrogen compared to 45 mJ/kg for natural gas. With these caveats in mind, an

  1. Relationships, variety & synergy: the vital ingredients for scholarship in engineering education? A case study

    Science.gov (United States)

    Clark, Robin; Andrews, Jane

    2014-11-01

    This paper begins with the argument that within modern-day society, engineering has shifted from being the scientific and technical mainstay of industrial, and more recently digital change to become the most vital driver of future advancement. In order to meet the inevitable challenges resulting from this role, the nature of engineering education is constantly evolving and as such engineering education has to change. The paper argues that what is needed is a fresh approach to engineering education - one that is sufficiently flexible so as to capture the fast-changing needs of engineering education as a discipline, whilst being pedagogically suitable for use with a range of engineering epistemologies. It provides an overview of a case study in which a new approach to engineering education has been developed and evaluated. The approach, which is based on the concept of scholarship, is described in detail. This is followed by a discussion of how the approach has been put into practice and evaluated. The paper concludes by arguing that within today's market-driven university world, the need for effective learning and teaching practice, based in good scholarship, is fundamental to student success.

  2. Intelligent systems in technical and medical diagnostics

    CERN Document Server

    Korbicz, Jozef

    2013-01-01

    For many years technical and medical diagnostics has been the area of intensive scientific research. It covers well-established topics as well as emerging developments in control engineering, artificial intelligence, applied mathematics, pattern recognition and statistics. At the same time, a growing number of applications of different fault diagnosis methods, especially in electrical, mechanical, chemical and medical engineering, is being observed. This monograph contains a collection of 44 carefully selected papers contributed by experts in technical and medical diagnostics, and constitutes

  3. Technical guide to criticality alarm system design

    International Nuclear Information System (INIS)

    Greenfield, B.

    2009-01-01

    An instructional manual was created to guide criticality safety engineers through the technical aspects of designing a criticality alarm system (CAS) for Dept. of Energy (DOE) hazard class 1 and 2 facilities. The manual was structured such that it can be used by engineers designing completely new systems and by those who are working with existing facilities. Major design tasks are thoroughly analyzed to provide concise direction for how to complete the analysis. Regulatory and technical performance requirements were both addressed. (authors)

  4. Advantages of shift changeovers with meetings: ergonomic analysis of shift supervisors' activity in aircraft building.

    Science.gov (United States)

    Le Bris, Valérie; Barthe, Béatrice; Marquié, Jean-Claude; Kerguelen, Alain; Aubert, Sophie; Bernadou, Bernadette

    2012-03-01

    Good shift changeovers contribute to ensuring continuity and reliability in shift work. In situations where production is not maintained 24 h a day, changeovers with meetings (SCM) between the two work teams (written plus oral face-to-face handovers) alternate with changeovers without meetings (SCnM; written handovers only). An ergonomic work analysis on an aircraft assembly line showed that (1) incoming and outgoing operators met during the overlap time allotted by the company, and (2) the content of the exchanges was richer for SCMs than for SCnMs. SCMs enabled the operators to pass on and process more aspects of their work than SCnMs did. SCMs also allowed incoming operators to validate their predictions, and enabled both outgoing and incoming operators to update their mental models and work together on peripheral aspects of the technical process over a greater time span. The findings highlight the importance of allowing overlap time in shift work. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  5. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 26: The technical communication practices of aerospace engineering students: Results of the phase 3 AIAA National Student Survey

    Science.gov (United States)

    Pinelli, Thomas E.; Hecht, Laura M.; Barclay, Rebecca O.; Kennedy, John M.

    1994-01-01

    This report describes similarities and differences between undergraduate and graduate engineering students in the context of two general aspects of the educational experience. First, we explore the extent to which students differ regarding the factors that lead to the choice of becoming an engineer, current satisfaction with that choice, and career-related goals and objectives. Second, we look at the technical communication practices, habits, and training of aerospace engineering students. The reported data were obtained from a survey of student members of the American Institute of Aeronautics and Astronautics (AIAA). The survey was undertaken as a phase 3 activity of the NASA/DoD Aerospace Knowledge Diffusion Research Project. Data are reported for the following categories: student demographics; skill importance, skill training, and skill helpfulness; collaborative writing; computer and information technology use and importance; use of electronic networks; use and importance of libraries and library services; use and importance of information sources and products; use of foreign language technical reports; and foreign language (reading and speaking) skills.

  6. Factors affecting employee attrition among engineers and non-engineers in manufacturing industry

    Directory of Open Access Journals (Sweden)

    Bhardwaj, Shikha

    2017-12-01

    Full Text Available Almost every industry nowadays is badly affected by attrition. Retention of talented employees is the biggest problem faced by India Incorporation. In order to gather more insights on the talent crunch, the undertaken study was conducted on technical and non-technical jobs in manufacturing sector in Delhi NCR. Research has identified three major factors – Salary, Boss and Stress in the jobs after conducted interviews with around 50 technical and non-technical respondents. A set of questions were prepared and send to 120 employee but only 75 responded. The study shows a strong relationship between type of job and factors of attrition. Chi-square test clearly states strong relationship among two. Thus, any change in one will affect the other also. At the same time other important outcomes were that for technical jobs salary is the most important factor whereas non-technical Boss is the factor. Out 75, 63 were engineer and rest were non-engineer. The research can be further done to understand factors of attrition with other demographic variable.

  7. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 28: The technical communication practices of aerospace engineering and science students: Results of the phase 4 cross-national surveys

    Science.gov (United States)

    Pinelli, Thomas E.; Hecht, Laura M.; Barclay, Rebecca O.; Kennedy, John M.

    1994-01-01

    This report describes similarities and differences between undergraduate and graduate aerospace engineering and science students in the context of two general aspects of the educational experience. First, we explore the extent to which students differ regarding the factors that lead to the choice of becoming an aerospace engineer or a scientist, current satisfaction with that choice, and career-related goals and objectives. Second, we look at the technical communication skills, practices, habits, and training of aerospace engineering and science students. The reported data were obtained from a survey of students enrolled in aerospace engineering and science programs at universities in India, Japan, Russia, and the United Kingdom. The surveys were undertaken as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. Data are reported for the following categories: student demographics; skill importance, skill training, and skill helpfulness; collaborative writing; computer and information technology use and importance, use of electronic networks; use and importance of libraries and library services; use and importance of information sources and products; use of foreign language technical reports; and foreign language (reading and speaking) skills.

  8. SWEBOS – The Software Engineering Body of Skills

    Directory of Open Access Journals (Sweden)

    Yvonne Sedelmaier

    2015-02-01

    Full Text Available The development of complex software systems requires a mixture of various technical and non-technical competencies. While some guidelines exist which technical knowledge is required to make a good software engineer, there is a lack of insight as to which non-technical or soft skills are necessary to master complex software projects. This paper proposes a body of skills (SWEBOS for soft-ware engineering. The collection of necessary skills is developed on the basis of a clear, data-driven research design. The resulting required soft skills for software engineering are described precisely and semantically rich in a three-level structure. This approach guarantees that skills are not just characterized in a broad and general manner, but rather they are specifically adapted to the domain of software engineering.

  9. Technical resource documents and technical handbooks for hazardous-wastes management

    Energy Technology Data Exchange (ETDEWEB)

    Schomaker, N.B.; Bliss, T.M.

    1986-07-01

    The Environmental Protection Agency is preparing a series of Technical Resource Documents (TRD's) and Technical Handbooks to provide best engineering control technology to meet the needs of the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) respectively. These documents and handbooks are basically compilation of research efforts of the Land Pollution Control Division (LPCD) to date. The specific areas of research being conducted under the RCRA land disposal program relate to laboratory, pilot and field validation studies in cover systems, waste leaching and solidification, liner systems and disposal facility evaluation. The technical handbooks provide the EPA Program Offices and Regions, as well as the states and other interested parties, with the latest information relevant to remedial actions.

  10. Designing socio-technical systems : Structures and processes

    NARCIS (Netherlands)

    Bots, P.W.G.; Van Daalen, C.

    2012-01-01

    The Systems Engineering, Policy Analysis and Management (SEPAM) MSc curriculum taught at Delft University of Technology focuses on the design of socio-technical systems (STS). We teach our students to structure design activities by considering what we call the TIP aspects: Technical systems,

  11. Assessing the damage importance rank in acoustic diagnostics of technical conditions of the internal combustion engine with multi-valued logical decision trees

    Directory of Open Access Journals (Sweden)

    Deptuła Adam

    2017-01-01

    Full Text Available This paper presents possible applications of acoustic diagnostics in inspecting the technical condition of an internal combustion engine with autoignition on the example of the Fiat drive unit with the common rail system. As a result of measuring the sound pressure level for specific faults and comparing the noise generated by the motor running smoothly, the detailed maps of changes in the acoustic spectrum may be generated. These results may be helpful in future diagnostics of internal combustion engines. In the paper, we present the results from the scientific works in the area of research, design and operation of internal combustion engines, conducted at the Department of Automotive Engineering, in cooperation with the Laboratory of Hydraulic Drives & Vibroacoustics of Machines at the Wroclaw University of Technology. The broader study has so far allowed us to develop an authoritative method of identifying the type of engine damage using gametree structures. The present works assess the possibility of using multi-valued logic trees.

  12. Competences in Demand within the Spanish Agricultural Engineering Sector

    Science.gov (United States)

    Perdigones, Alicia; Valera, Diego Luis; Moreda, Guillermo Pedro; García, Jose Luis

    2014-01-01

    The Rural Engineering Department (Technical University of Madrid) ran three competence surveys during the 2006-2007 and 2007-2008 academic years and evaluated: (1) the competences gained by agricultural engineer's degree and agricultural technical engineer's degree students (360 respondents); (2) the competences demanded by agricultural employers…

  13. Educating the humanitarian engineer.

    Science.gov (United States)

    Passino, Kevin M

    2009-12-01

    The creation of new technologies that serve humanity holds the potential to help end global poverty. Unfortunately, relatively little is done in engineering education to support engineers' humanitarian efforts. Here, various strategies are introduced to augment the teaching of engineering ethics with the goal of encouraging engineers to serve as effective volunteers for community service. First, codes of ethics, moral frameworks, and comparative analysis of professional service standards lay the foundation for expectations for voluntary service in the engineering profession. Second, standard coverage of global issues in engineering ethics educates humanitarian engineers about aspects of the community that influence technical design constraints encountered in practice. Sample assignments on volunteerism are provided, including a prototypical design problem that integrates community constraints into a technical design problem in a novel way. Third, it is shown how extracurricular engineering organizations can provide a theory-practice approach to education in volunteerism. Sample completed projects are described for both undergraduates and graduate students. The student organization approach is contrasted with the service-learning approach. Finally, long-term goals for establishing better infrastructure are identified for educating the humanitarian engineer in the university, and supporting life-long activities of humanitarian engineers.

  14. Formal modelling and analysis of socio-technical systems

    DEFF Research Database (Denmark)

    Probst, Christian W.; Kammüller, Florian; Hansen, Rene Rydhof

    2016-01-01

    systems are still mostly identified through brainstorming of experts. In this work we discuss several approaches to formalising socio-technical systems and their analysis. Starting from a flow logic-based analysis of the insider threat, we discuss how to include the socio aspects explicitly, and show......Attacks on systems and organisations increasingly exploit human actors, for example through social engineering. This non-technical aspect of attacks complicates their formal treatment and automatic identification. Formalisation of human behaviour is difficult at best, and attacks on socio-technical...... a formalisation that proves properties of this formalisation. On the formal side, our work closes the gap between formal and informal approaches to socio-technical systems. On the informal side, we show how to steal a birthday cake from a bakery by social engineering....

  15. Descriptive analysis of context evaluation instrument for technical oral presentation skills evaluation: A case study in English technical communication course

    Science.gov (United States)

    Mohamed, Abdullah-Adnan; Asmawi, Adelina; Hamid, Mohd Rashid Ab; Mustafa, Zainol bin

    2015-02-01

    This paper reports a pilot study of Context Evaluation using a self-developed questionnaire distributed among engineering undergraduates at a university under study. The study aims to validate the self-developed questionnaires used in the Context evaluation, a component in the CIPP Model. The Context evaluation assesses background information for needs, assets, problems and opportunities relevant to beneficiaries of the study in a defined environment. Through the questionnaire, background information for the assessment of needs, assets and problems related to the engineering undergraduates' perceptions on the teaching and learning of technical oral presentation skills was collected and analysed. The questionnaire was developed using 5-points Likert scale to measure the constructs under study. They were distributed to 100 respondents with 79 returned. The respondents consisted of engineering undergraduates studied at various faculties at one technical university in Malaysia. The descriptive analysis of data for each item which makes up the construct for Context evaluation is found to be high. This implied that engineering undergraduates showed high interest in teaching and learning of technical oral presentation skills, thus their needs are met. Also, they agreed that assets and facilities are conducive to their learning. In conclusion, the context evaluation involving needs and assets factors are both considerably important; their needs are met and the assets and facilities do support their technical oral presentation skills learning experience.

  16. Application and problems of probability methods in technical safety assessment in the field of nuclear engineering and other technologies

    International Nuclear Information System (INIS)

    Heuser, F.W.

    1980-01-01

    On the basis of a deterministic safety concept that has been developed in nuclear engineering, approaches for a probabilistic interpretation of existing safety requirements and for a further risk assessment are described. The procedures in technical reliability analysis and its application in nuclear engineering are discussed. By the example of a reliability analysis for a reactor protection system the author discusses the question as to what extent methods of reliability analysis can be used to interpret deterministically derived safety requirements. The the author gives a survey of the current value and application of probabilistic reliability assessments in non-nuclear technology. The last part of this report deals with methods of risk analysis and its use for safety assessment in nuclear engineering. On the basis of WASH 1,400 the most important phases and tasks of research work in risk assessment are explained, showing the basic criteria and the methods to be applied in risk analysis. (orig./HSCH) [de

  17. [NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 4:] Technical communications in aerospace: An analysis of the practices reported by US and European aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.; Glassman, Myron

    1990-01-01

    Results are reported from pilot surveys on the use of scientific and technical information (STI) by U.S. and NATO-nation aerospace scientists and engineers, undertaken as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. The survey procedures and the demographic characteristics of the 67 scientists and engineers who responded to the survey are summarized, and the results are presented in a series of tables and discussed in detail. Findings emphasized include: (1) both U.S. and NATO respondents spend around 60 percent of their work week producing or using STI products; (2) NATO respondents are more likely than their U.S. counterparts to use 'formal' STI products (like technical reports and papers) and the services of librarians and online data bases; (3) most of the respondents use computers and information technology in preparing STI products; and (4) respondents who had taken courses in technical communication agreed on the value and ideal subject matter of such courses.

  18. Technical assistance contractor Management Plan

    International Nuclear Information System (INIS)

    1993-09-01

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins ampersand Beckwith Agra, Inc. (SHB Agra), and Geraghty ampersand Miller, Inc. (G ampersand M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC's groundwater technical breadth and depth, so G ampersand M was brought in to augment the team's capabilities. The TAC contract's scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC's management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls

  19. Optimal control of the gear shifting process for shift smoothness in dual-clutch transmissions

    Science.gov (United States)

    Li, Guoqiang; Görges, Daniel

    2018-03-01

    The control of the transmission system in vehicles is significant for the driving comfort. In order to design a controller for smooth shifting and comfortable driving, a dynamic model of a dual-clutch transmission is presented in this paper. A finite-time linear quadratic regulator is proposed for the optimal control of the two friction clutches in the torque phase for the upshift process. An integral linear quadratic regulator is introduced to regulate the relative speed difference between the engine and the slipping clutch under the optimization of the input torque during the inertia phase. The control objective focuses on smoothing the upshift process so as to improve the driving comfort. Considering the available sensors in vehicles for feedback control, an observer design is presented to track the immeasurable variables. Simulation results show that the jerk can be reduced both in the torque phase and inertia phase, indicating good shift performance. Furthermore, compared with conventional controllers for the upshift process, the proposed control method can reduce shift jerk and improve shift quality.

  20. How engineers perceive the importance of ethics in Finland

    Science.gov (United States)

    Taajamaa, Ville; Majanoja, Anne-Maarit; Bairaktarova, Diana; Airola, Antti; Pahikkala, Tapio; Sutinen, Erkki

    2018-01-01

    Success in complex and holistic engineering practices requires more than problem-solving abilities and technical competencies. Engineering education must offer proficient technical competences and also train engineers to think and act ethically. A technical 'engineering-like' focus and demand have made educators and students overlook the importance of ethical awareness and transversal competences. Using two Finnish surveys, conducted in 2014 and 2016, we examine how engineers perceive working life needs regarding ethics. The data consider different age groups. We research whether an engineer's age affects their perception of the importance of ethics in their work and if there are differences between young experts and young managers in their use of ethics within work. The results indicate that practising engineers do not consider ethical issues important in their work. This especially applies to younger engineers; the older an engineer, the more important they consider ethics. No statistically significant difference was found between young engineering experts and managers.

  1. Technical Assistance Contractor management plan. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) as the prime contractor and three teaming partner subcontractors: Roy F. Weston, Inc. (RFW), AGRA Earth and Environmental, Inc. (AGRA), and Geraghty and Miller, Inc. (G and M). The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both Surface and Ground Water Projects. The TAC team supports the DOE in completing surface remedial action and initiating ground water remediation work for start-up, characterization, compliance planning, design, construction oversight, and remedial operations. The TAC provides the DOE UMTRA Project Team with a dedicated management, scientific, and technical resource base in Albuquerque, New Mexico, which is supplemented by corporate resources. A carefully developed and maintained staff of technical experts is available to assess, analyze, develop, and execute cost-effective solutions to the demanding technical and institutional problems presented by the UMTRA Project.

  2. Tank waste remediation system engineering plan

    International Nuclear Information System (INIS)

    Rifaey, S.H.

    1998-01-01

    This Engineering Plan describes the engineering process and controls that will be in place to support the Technical Baseline definition and manage its evolution and implementation to the field operations. This plan provides the vision for the engineering required to support the retrieval and disposal mission through Phase 1 and 2, which includes integrated data management of the Technical Baseline. Further, this plan describes the approach for moving from the ''as is'' condition of engineering practice, systems, and facilities to the desired ''to be'' configuration. To make this transition, Tank Waste Remediation System (TWRS) Engineering will become a center of excellence for TWRS which,will perform engineering in the most effective manner to meet the mission. TWRS engineering will process deviations from sitewide systems if necessary to meet the mission most effectively

  3. Electronic resource management practical perspectives in a new technical services model

    CERN Document Server

    Elguindi, Anne

    2012-01-01

    A significant shift is taking place in libraries, with the purchase of e-resources accounting for the bulk of materials spending. Electronic Resource Management makes the case that technical services workflows need to make a corresponding shift toward e-centric models and highlights the increasing variety of e-formats that are forcing new developments in the field.Six chapters cover key topics, including: technical services models, both past and emerging; staffing and workflow in electronic resource management; implementation and transformation of electronic resource management systems; the ro

  4. Sandia Laboratories technical capabilities: engineering analysis

    International Nuclear Information System (INIS)

    Lundergan, C.D.

    1975-12-01

    This report characterizes the engineering analysis capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs

  5. Technology and automation of atomic power engineering and industry. TAAPEI-2009. Materials of branch scientific and technical conference covers the fiftieth anniversary of the Seversk State Engineering Academy

    International Nuclear Information System (INIS)

    2009-01-01

    Materials of the branch scientific and technical conference Technology and automation of atomic power engineering and industry (18-22 May, 2009, Seversk) are performed. Scientific and practical results of investigations into chemical technological developments, creation of machinery and apparatuses, automation of technological processes, application of present-day information technologies in atomic industry as well as ecological and nuclear weapons proliferation problems are shown. Besides issues of professional education and social-economic problems of the atomic branch are considered [ru

  6. Towards common technical standards

    International Nuclear Information System (INIS)

    Rahmat, H.; Suardi, A.R.

    1993-01-01

    In 1989, PETRONAS launched its Total Quality Management (TQM) program. In the same year the decision was taken by the PETRONAS Management to introduce common technical standards group wide. These standards apply to the design, construction, operation and maintenance of all PETRONAS installations in the upstream, downstream and petrochemical sectors. The introduction of common company standards is seen as part of an overall technical management system, which is an integral part of Total Quality Management. The Engineering and Safety Unit in the PETRONAS Central Office in Kuala Lumpur has been charged with the task of putting in place a set of technical standards throughout PETRONAS and its operating units

  7. NASA Technical Reports Server (NTRS)

    Data.gov (United States)

    National Aeronautics and Space Administration — The NTRS is a valuable resource for researchers, students, educators, and the public to access NASA's current and historical technical literature and engineering...

  8. Data engineering systems: Computerized modeling and data bank capabilities for engineering analysis

    Science.gov (United States)

    Kopp, H.; Trettau, R.; Zolotar, B.

    1984-01-01

    The Data Engineering System (DES) is a computer-based system that organizes technical data and provides automated mechanisms for storage, retrieval, and engineering analysis. The DES combines the benefits of a structured data base system with automated links to large-scale analysis codes. While the DES provides the user with many of the capabilities of a computer-aided design (CAD) system, the systems are actually quite different in several respects. A typical CAD system emphasizes interactive graphics capabilities and organizes data in a manner that optimizes these graphics. On the other hand, the DES is a computer-aided engineering system intended for the engineer who must operationally understand an existing or planned design or who desires to carry out additional technical analysis based on a particular design. The DES emphasizes data retrieval in a form that not only provides the engineer access to search and display the data but also links the data automatically with the computer analysis codes.

  9. Shape-shifting colloids via stimulated dewetting

    Science.gov (United States)

    Youssef, Mena; Hueckel, Theodore; Yi, Gi-Ra; Sacanna, Stefano

    2016-01-01

    The ability to reconfigure elementary building blocks from one structure to another is key to many biological systems. Bringing the intrinsic adaptability of biological systems to traditional synthetic materials is currently one of the biggest scientific challenges in material engineering. Here we introduce a new design concept for the experimental realization of self-assembling systems with built-in shape-shifting elements. We demonstrate that dewetting forces between an oil phase and solid colloidal substrates can be exploited to engineer shape-shifting particles whose geometry can be changed on demand by a chemical or optical signal. We find this approach to be quite general and applicable to a broad spectrum of materials, including polymers, semiconductors and magnetic materials. This synthetic methodology can be further adopted as a new experimental platform for designing and rapidly prototyping functional colloids, such as reconfigurable micro swimmers, colloidal surfactants and switchable building blocks for self-assembly. PMID:27426418

  10. Development of Engineering Design Education in the Department of Mechanical Engineering at Kanazawa Technical College

    Science.gov (United States)

    Yamada, Hirofumi; Ten-Nichi, Michio; Mathui, Hirosi; Nakamura, Akizi

    This paper introduces a method of the engineering design education for college of technology mechanical engineering students. In order to teach the practical engineering design, the MIL-STD-499A process is adapted and improved upon for a Mechatronics hands-on lesson used as the MOT method. The educational results in five years indicate that knowledge of the engineering management is useful for college students in learning engineering design. Portfolio for lessons and the hypothesis method also have better effects on the understanding of the engineering specialty.

  11. Consolidation on civil engineering and technical infrastructure at CERN from now to 2010

    CERN Document Server

    Alves, P; Pepinster, P; CERN. Geneva. ST Division

    2003-01-01

    The age of the civil engineering structure (office buildings, halls) and of tertiary technical equipment (mainly HVAC and electricity) at CERN is such that their renovation must be considered in the near future. Due to the large number of buildings and equipment in these conditions, and the restricted budget available, it is extremely important to define priorities. The aim of this note is to give the picture of the current conditions and the related problems, based on the backlog of CERN database (MP5) and confronting it with the inventory made at CERN by an external company. After having identified the most frequent problems and repairs to carry out, a planning for intervention is therefore presented optimizing the safety aspects, maintenance costs and comfort for the users. The timescale of this intervention is related to the money that will be available in the coming years.

  12. A socio-technical approach to teaching the social impacts of technological development

    DEFF Research Database (Denmark)

    Jensen, Per Langå; Broberg, Ole

    2001-01-01

    This paper describes a socio-technical approach to teach work environment in an en-gineering education as an alternative to a science-based presentation of each potential harmful factor. The socio-technical approach emphasizes that work environment must be understood in a social context and that ......This paper describes a socio-technical approach to teach work environment in an en-gineering education as an alternative to a science-based presentation of each potential harmful factor. The socio-technical approach emphasizes that work environment must be understood in a social context...

  13. Encouraging the Learning of Hydraulic Engineering Subjects in Agricultural Engineering Schools

    Science.gov (United States)

    Sinobas, Leonor Rodríguez; Sánchez Calvo, Raúl

    2014-01-01

    Several methodological approaches to improve the understanding and motivation of students in Hydraulic Engineering courses have been adopted in the Agricultural Engineering School at Technical University of Madrid. During three years student's progress and satisfaction have been assessed by continuous monitoring and the use of…

  14. Colloid process engineering

    CERN Document Server

    Peukert, Wolfgang; Rehage, Heinz; Schuchmann, Heike

    2015-01-01

    This book deals with colloidal systems in technical processes and the influence of colloidal systems by technical processes. It explores how new measurement capabilities can offer the potential for a dynamic development of scientific and engineering, and examines the origin of colloidal systems and its use for new products. The future challenges to colloidal process engineering are the development of appropriate equipment and processes for the production and obtainment of multi-phase structures and energetic interactions in market-relevant quantities. The book explores the relevant processes and for controlled production and how they can be used across all scales.

  15. Team-Based Development of Medical Devices: An Engineering-Business Collaborative.

    Science.gov (United States)

    Eberhardt, Alan W; Johnson, Ophelia L; Kirkland, William B; Dobbs, Joel H; Moradi, Lee G

    2016-07-01

    There is a global shift in the teaching methodology of science and engineering toward multidisciplinary, team-based processes. To meet the demands of an evolving technical industry and lead the way in engineering education, innovative curricula are essential. This paper describes the development of multidisciplinary, team-based learning environments in undergraduate and graduate engineering curricula focused on medical device design. In these programs, students actively collaborate with clinicians, professional engineers, business professionals, and their peers to develop innovative solutions to real-world problems. In the undergraduate senior capstone courses, teams of biomedical engineering (BME) and business students have produced and delivered numerous functional prototypes to satisfied clients. Pursuit of commercialization of devices has led to intellectual property (IP) disclosures and patents. Assessments have indicated high levels of success in attainment of student learning outcomes and student satisfaction with their undergraduate design experience. To advance these projects toward commercialization and further promote innovative team-based learning, a Master of Engineering (MEng) in Design and Commercialization was recently launched. The MEng facilitates teams of graduate students in engineering, life sciences, and business who engage in innovation-commercialization (IC) projects and coursework that take innovative ideas through research and development (R&D) to create marketable devices. The activities are structured with students working together as a "virtual company," with targeted outcomes of commercialization (license agreements and new start-ups), competitive job placement, and/or career advancement.

  16. Formal Modelling and Analysis of Socio-Technical Systems

    NARCIS (Netherlands)

    Probst, Christian W.; Kammüller, Florian; Rydhof Hansen, René; Probst, Christian W.; Hankin, Chris; Rydhof Hansen, René

    2015-01-01

    Attacks on systems and organisations increasingly exploit human actors, for example through social engineering. This non-technical aspect of attacks complicates their formal treatment and automatic identification. Formalisation of human behaviour is difficult at best, and attacks on socio-technical

  17. Fundamentals of civil engineering an introduction to the ASCE body of knowledge

    CERN Document Server

    McCuen, Richard H; Wong, Melanie K

    2011-01-01

    While the ASCE Body of Knowledge (BOK2) is the codified source for all technical and non-technical information necessary for those seeking to attain licensure in civil engineering, recent graduates have notoriously been lacking in the non-technical aspects even as they excel in the technical. Fundamentals of Civil Engineering: An Introduction to the ASCE Body of Knowledge addresses this shortfall and helps budding engineers develop the knowledge, skills, and attitudes suggested and implied by the BOK2. Written as a resource for all of the non-technical outcomes not specifically covered in the

  18. Engineering of complex systems: The impact of systems engineering at NASA

    Science.gov (United States)

    Kludze, Ave-Klutse Kodzo Paaku

    The "true" impact or value of systems engineering to an organization unfortunately appears not to have been well-studied and understood. The principles of systems engineering are highly encouraged by NASA at all levels, and most practitioners, both internal and external to NASA, intuitively "believe" it adds some value to the development of complex systems by producing them faster, better and cheaper. This research, in trying to fill a gap that exists in the systems engineering literature, analyzes data collected within NASA and other sources external to NASA (INCOSE) for comparisons. Analyses involving a number of case studies performed on selected NASA projects are presented to draw attention to the impact systems engineering had or could have had on these projects. This research clearly shows that systems engineering does add value to projects within and outside NASA. The research results further demonstrate that systems engineering has been beneficial not only to NASA but also to organizations within which INCOSE members work. It was determined, however, that systems engineering does not operate in a vacuum and may not always guarantee success through mere application. During this research, it was discovered that the lack of or inadequate application of systems engineering in the development of complex systems may result in cost overruns, poor technical performance, project delays, and in some cases unmitigated risk with disastrous consequences including the loss of life and property. How much is saved (in terms of cost, schedule) or improved (in terms of technical performance) as a result of its implementation may never be known precisely, but by indirectly measuring its value or impact on a project, percentages of project budget spent on systems engineering activities and any schedule reductions or performance enhancements realized could be determined. According to this research, systems engineering is not a waste of time and resources; in most cases, it is

  19. Minutes of the IFMIF technical meetings, May 17-20, 2005, Tokyo, Japan

    International Nuclear Information System (INIS)

    Ida, Mizuho; Nakamura, Hiroo; Yutani, Toshiaki; Maebara, Sunao; Umetsu, Tomotake; Sugimoto, Masayoshi

    2005-08-01

    The International Fusion Materials Irradiation Facility (IFMIF) Technical Meetings were held on May 17-20, 2005 at Japan Atomic Energy Research Institute (JAERI) Tokyo. The main objectives were 1) to review technical status of the subsystems; accelerator, target and test facilities, 2) to technically discuss interface issues between target and test facilities, 3) to review results of peer-reviews performed in the EU and Japan, 4) to harmonize design/experimental activities among the subsystems, 5) to review and discuss the Engineering Validation and Engineering Design Activity (EVEDA) tasks, and 6) to make a report of 1) - 5) to the IFMIF Executive Subcommittee. This report presents a brief summary of the Target Technical, Meeting, Test Facilities Technical Meeting, Target/Test Facilities Interface Meeting, Accelerator Technical Meeting and the Technical Integration Meeting. (author)

  20. Job and task analysis for technical staff

    International Nuclear Information System (INIS)

    Toline, B.C.

    1991-01-01

    In September of 1989 Cooper Nuclear Station began a project to upgrade the Technical Staff Training Program. This project's roots began by performing job and Task Analysis for Technical Staff. While the industry has long been committed to Job and Task Analysis to target performance based instruction for single job positions, this approach was unique in that it was not originally considered appropriate for a group as diverse as Tech Staff. Much to his satisfaction the Job and Task Analysis Project was much less complicated for Technical Staff than the author had imagined. The benefits of performing the Job and Task Analysis for Technical Staff have become increasingly obvious as he pursues lesson plan development and course revisions. The outline for this presentation will be as follows: philosophy adopted; preparation of the job survey document; performing the job analysis; performing task analysis for technical staff and associated pitfalls; clustering objectives for training and comparison to existing program; benefits now and in the future; final phase (comparison to INPO guides and meeting the needs of non-degreed engineering professionals); and conclusion. By focusing on performance based needs for engineers rather than traditional academics for training the author is confident the future Technical Staff Program will meet the challenges ahead and will exceed requirements for accreditation

  1. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 52: A comparison of the technical communications practices of Japanese and US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Holloway, Karen; Sato, Yuko; Barclay, Rebecca O.; Kennedy, John M.

    1995-01-01

    To understand the diffusion of aerospace knowledge, it is necessary to understand the communications practices and the information-seeking behaviors of those involved in the production, transfer, and use of aerospace knowledge at the individual, organizational, national, and international levels. In this paper, we report selected results from a survey of Japanese and U.S. aerospace engineers and scientists that focused on communications practices and information-seeking behaviors in the workplace. Data are presented for the following topics: importance of and time spent communicating information, collaborative writing, need for an undergraduate course in technical communications, use of libraries, the use and importance of electronic (computer) networks, and the use and importance of foreign and domestically produced technical reports. The responses of the survey respondents are placed within the context of the Japanese culture. We assume that differences in Japanese and U.S. cultures influence the communications practices and information-seeking behaviors of Japanese and U.S. aerospace engineers and scientists.

  2. Advanced Combustion and Emission Control Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Advanced Combustion and Emission Control (ACEC) Technical Team is focused on removing technical barriers to the commercialization of advanced, high-efficiency, emission-compliant internal combustion (IC) engines for light-duty vehicle powertrains (i.e., passenger car, minivan, SUV, and pickup trucks).

  3. Process of technical performance: essential features and their economic view

    OpenAIRE

    Zhylinska, O.

    2010-01-01

    Essential features of technical performance have been defined in the context of similarity of its components such as research and development, training of technical/engineering personnel and providing technical services. Also peculiarities of economic view have been examined in terms of information model of managing.

  4. ITER technical advisory committee meeting

    International Nuclear Information System (INIS)

    Fujiwara, M.

    1999-01-01

    The ITER Technical Advisory Committee (TAC) meeting took place on December 20-22, 1999 at the Naka Joint Work Site. The objective of this meeting was to review the document 'Technical Basis for ITER-FEAT Outline Design (ODR)' issued by the Director on December 10. It was also aimed at providing the ITER Meeting scheduled for January 19-20, 2000 in Tokyo with a technical assessment of ODR and recommendations for the optimization of the anticipated plasma performance and engineering design, based on the guidelines approved by the Council in June 1998 and recommendations of the last TAC meeting

  5. Technical Training: Technical Training Seminar

    CERN Multimedia

    2004-01-01

    TECHNICAL TRAINING Monique Duval tel. 74924 technical.training@cern.ch Tuesday 3 February 2004 From 09:00 to 13:30 - Training Centre Auditorium - bldg. 593, room 11 USB (Universal Serial Bus) CYPRESS Seminar Claudia Colombini, Field Application Engineer CYPRESS ActiveComp Electronic GmbH D-85077 MANCHING, Germany As a pioneer in USB, CYPRESS sets the standard for cost-effective solutions without sacrificing functionality, performance or reliability. Having shipped over 200 million USB devices, Cypress is the undisputed market leader and demonstrates unmatched USB expertise. With the industry's broadest selection of USB solutions, Cypress has the right silicon, software and support for every USB application, from Low-speed to High-Speed and USB On-The-Go (OTG). 9:00 - 10:30 Overview of USB systems. USB CYPRESS product overview. Peripherals: Low Speed, Full Speed, High Speed (1.1 and 2.0). Hub Solutions, Embedded Host Solutions, On-The-Go (OTG) and wireless USB. USB Development Tools (first part) 10:30 -...

  6. Engineering ethics challenges and opportunities

    CERN Document Server

    Bowen, W Richard

    2014-01-01

    Engineering Ethics: Challenges and Opportunities aims to set a new agenda for the engineering profession by developing a key challenge: can the great technical innovation of engineering be matched by a corresponding innovation in the acceptance and expression of ethical responsibility?  Central features of this stimulating text include:   ·         An analysis of engineering as a technical and ethical practice providing great opportunities for promoting the wellbeing and agency of individuals and communities. ·         Elucidation of the ethical opportunities of engineering in three key areas:             - Engineering for Peace, emphasising practical amelioration of the root causes of    conflict rather than military solutions.             - Engineering for Health, focusing on close collaboration with healthcare professionals      for both the promotion and restoration of health.             - Engineering for Development, providing effective solution...

  7. Analysis Influence of Managerial Competence, Technical Competence, and Strategic Competence on Firm Performance in Electrical Engineering Company in Bandung

    Science.gov (United States)

    Wijaya, E. R.; Irianto, D.

    2018-03-01

    The industry sectors that have an important role in the era of globalization is the electro engineering sector. The era of globalization led to intense competition. One of the negative effects of the intense competition is declining profits. Drop in profits caused many firms reduces their employees without seeking the root cause of declining profits in detail. Whereas, employee is the important resources to maintain competitive advantage. Competitive advantage can be measured by the performance of which is owned by the firm. The firm's performance can be formed of competencies that is unique, rare, irreplaceable, and difficult to imitate within the firm, one of them is the competence of the individual. According to a competency-based approach and the resource- based approach, individual competence that affect the performance of the firm is managerial competence, technical competence, and strategic competence. Questionnaire is built based on the dimensions of the firm's performance, managerial competence, technical competence, and strategic competence, are processed using partial least squares application. The results indicate that managerial competence negatively impact firm’s performance with weak ties. The technical competence and strategic competence positively affect firm’s performance with moderate ties.

  8. Understanding of photosynthesis among pupils of technical secondary schools

    OpenAIRE

    Pavić, Petra

    2014-01-01

    The goal of our research was to examine the knowledge on photosynthesis of the students of the Secondary Technical schools, and their attitude towards it, and whether they have misconceptions about it. The research was conducted on a sample of 466 students in Vegova Secondary Technical and Grammar School of Electrical Engineering and Computer Science in Ljubljana in the first, second and third year of electrical engineering and computer science programme. The test contained 27 closed-ended qu...

  9. Effects of Human Factors in Engineering and Design for Teaching Mathematics: A Comparison Study of Online and Face-to-Face at a Technical College

    Science.gov (United States)

    Mativo, John M.; Hill, Roger B.; Godfrey, Paul W.

    2013-01-01

    The focus of this study was to examine four characteristics for successful and unsuccessful students enrolled in basic mathematics courses at a technical college. The characteristics, considered to be in part effects of human factors in engineering and design, examined the preferred learning styles, computer information systems competency,…

  10. Illustration of an analytical method for quantification of the safety of technical appliances

    International Nuclear Information System (INIS)

    Tegel, M.

    1981-01-01

    The safety analysis of technical products will in future be required more and more also for simple technical systems. The fault-tree analysis is a method for safety judgement used in particular in aviation and space engineering as well as in energy engineering. This analytical method can also be applied to simple technical constructions, as the article shows, using as example an acially rotatable load hook. (orig.) [de

  11. Outsiders Looking In: Tutor Expertise in Engineering Writing

    Science.gov (United States)

    Bengesai, Annah

    2015-01-01

    Drawing on an academic literacies approach, this article explores the representations of technical communication by non-content expert tutors teaching the Technical Communication for Engineering course at a South African university. The course is offered to all first year engineering students as a developmental academic literacy course. It is…

  12. Integrated engineering system for nuclear facilities building

    International Nuclear Information System (INIS)

    Tomura, H.; Miyamoto, A.; Futami, F.; Yasuda, S.; Ohtomo, T.

    1995-01-01

    In the construction of buildings for nuclear facilities in Japan, construction companies are generally in charge of the building engineering work, coordinating with plant engineering. An integrated system for buildings (PROMOTE: PROductive MOdeling system for Total nuclear Engineering) described here is a building engineering system including the entire life cycle of buildings for nuclear facilities. A Three-dimensional (3D) building model (PRO-model) is to be in the core of the system (PROMOTE). Data sharing in the PROMOTE is also done with plant engineering systems. By providing these basic technical foundations, PROMOTE is oriented toward offering rational, highquality engineering for the projects. The aim of the system is to provide a technical foundation in building engineering. This paper discusses the characteristics of buildings for nuclear facilities and the outline of the PROMOTE. (author)

  13. Bioethics for Technical Experts

    Science.gov (United States)

    Asano, Shigetaka

    Along with rapidly expanding applications of life science and technology, technical experts have been implicated more and more often with ethical, social, and legal problems than before. It should be noted that in this background there are scientific and social uncertainty elements which are inevitable during the progress of life science in addition to the historically-established social unreliability to scientists and engineers. In order to solve these problems, therefore, we should establish the social governance with ‘relief’ and ‘reliance’ which enables for both citizens and engineers to share the awareness of the issues, to design social orders and criterions based on hypothetical sense of values for bioethics, to carry out practical use management of each subject carefully, and to improve the sense of values from hypothetical to universal. Concerning these measures, the technical experts can learn many things from the present performance in the medical field.

  14. Civil engineering work

    International Nuclear Information System (INIS)

    Cousyn, Rene; Goubin, Jean.

    1977-01-01

    Although it does not require a specifically new technicality, the Civil Engineering site of a nuclear power plant is a complex work. Considering as an example the power plant currently in construction at Tricastin, the authors describe the main Civil Engineering work and task organization applied to carry it out [fr

  15. Contribution of developing advanced engineering methods in interdisciplinary studying the piston rings from 1.6 spark ignited Ford engine at Technical University of Cluj-Napoca

    Science.gov (United States)

    -Aurel Cherecheş, Ioan; -Ioana Borzan, Adela; -Laurean Băldean, Doru

    2017-10-01

    Study of construction and wearing process in the case of piston-rings and other significant components from internal combustion engines leads at any time to creative and useful optimizing ideas, both in designing and manufacturing phases. Main objective of the present paper is to realize an interdisciplinary research using advanced methods in piston-rings evaluation of a common vehicle on the streets which is Ford Focus FYDD. Specific objectives are a theoretical study of the idea for advanced analysis method in piston-rings evaluation and an applied research developed in at Technical University from Cluj-Napoca with the motor vehicle caught in the repairing process.

  16. Program plan for the DOE Office of Fusion Energy First Wall/Blanket/Shield Engineering Technology Program. Volume II. Detailed technical plan. Revision 2

    International Nuclear Information System (INIS)

    1982-08-01

    The four sections which comprise Part II describe in detail the technical basis for each of the four Program Elements (PE's) of the FWBS Engineering Technology Program (ETP). Each PE is planned to be executed in a number of phases. The purpose of the DTP's is to delineate detailed near-term research, development, and testing required to establish a FWBS engineering data base. Optimum testing strategies and construction of test facilities where needed are identified. The DTP's are based on guidelines given by Argonne National Laboratory which included the basic programmatic goals and the requirements for the types of tests and test conditions

  17. Procurement engineering - the productivity factor

    Energy Technology Data Exchange (ETDEWEB)

    Bargerstock, S.B. (TENERA, L.P., Chattanooga, TN (United States))

    1993-01-01

    The industry is several years on the road to implementation of the Nuclear Management and Resources Council (NUMARC) initiatives on commercial-grade item dedication and procurement. Utilities have taken several approaches to involve engineering in the procurement process. A common result for the approaches is the additional operations and maintenance (O M) cost imposed by the added resource requirements. Procurement engineering productivity is a key element in controlling this business area. Experience shows that 400 to 500% improvements in productivity are possible with a 2-yr period. Improving the productivity of the procurement engineering function is important in today's competitive utility environment. Procurement engineering typically involves four distinct technical evaluation responsibilities along with several administrative areas. Technical evaluations include the functionally based safety classification of replacement components and parts (lacking a master parts list), the determination of dedication requirements for safety-related commercial-grade items, the preparation of a procurement specification to maintain the licensed design bases, and the equivalency evaluation of alternate items not requiring the design-change process. Administrative duties include obtaining technical review of vendor-supplied documentation, identifying obsolete parts and components, resolving material nonconformances, initiating the design-change process for replacement items (as needed), and providing technical support to O M. Although most utilities may not perform or require all the noted activities, a large percentage will apply to each utility station.

  18. Procurement engineering - the productivity factor

    International Nuclear Information System (INIS)

    Bargerstock, S.B.

    1993-01-01

    The industry is several years on the road to implementation of the Nuclear Management and Resources Council (NUMARC) initiatives on commercial-grade item dedication and procurement. Utilities have taken several approaches to involve engineering in the procurement process. A common result for the approaches is the additional operations and maintenance (O ampersand M) cost imposed by the added resource requirements. Procurement engineering productivity is a key element in controlling this business area. Experience shows that 400 to 500% improvements in productivity are possible with a 2-yr period. Improving the productivity of the procurement engineering function is important in today's competitive utility environment. Procurement engineering typically involves four distinct technical evaluation responsibilities along with several administrative areas. Technical evaluations include the functionally based safety classification of replacement components and parts (lacking a master parts list), the determination of dedication requirements for safety-related commercial-grade items, the preparation of a procurement specification to maintain the licensed design bases, and the equivalency evaluation of alternate items not requiring the design-change process. Administrative duties include obtaining technical review of vendor-supplied documentation, identifying obsolete parts and components, resolving material nonconformances, initiating the design-change process for replacement items (as needed), and providing technical support to O ampersand M. Although most utilities may not perform or require all the noted activities, a large percentage will apply to each utility station

  19. On shift simulation in aeromedical operations - making it work

    Directory of Open Access Journals (Sweden)

    John Glasheen

    2017-06-01

    Full Text Available Patient care in the prehospital and retrieval medicine (PHARM environment presents many technical and non-technical challenges. Clinicians are frequently required to perform complex interventions in a time critical and resource limited setting. Intensive training is required prior to operational deployment, and ongoing training is vital to ensure optimal team performance in the delivery of high quality patient care. Regular simulation training with high situational fidelity is valuable in developing and maintaining excellence in PHARM. We describe the methods employed by two Australian aeromedical retrieval services to facilitate daily on shift simulation.

  20. Employment Shifts in the Technical and Further Education Workforce in Victoria.

    Science.gov (United States)

    Shah, Chandra

    2003-01-01

    Analyzes changes in Technical and Further Education (TAFE) work force in Victoria, Australia, that occurred during the period 1993-98. Main changes include increased participation of women, significant growth in part-time employment, decline in full-time (mainly male) employment, and an increased use of seasonal teachers. (Includes 10 figures and…

  1. Turning Technologies into Businesses- The Challenge for the Technical Entrepreneur

    Science.gov (United States)

    Glass, Alexander

    2000-03-01

    Over the past twenty-five years, new businesses based on innovative technology have been the driving force for the US economy. Due to the abundance of early-stage capital, each year, thousands of scientists and engineers receive support to start new, technology-based businesses. However, the transition from technologist to entrepreneur is often difficult. It requires a shift in emphasis from a technology focus to a market focus. We shall discuss the challenges facing the technical entrepreneur in launching a new enterprise, and a variety of resources that are available to help the entrepreneur succeed. Many technologists fall victim to the myth that if you ``build a better mousetrap, the world will beat a path to your door." To be sure, it is important to base your business on sound technology that offers a clear advantage over current practice, and, if possible, to secure title to the technology, either by obtaining patent protection, or securing an exclusive license. Once that is done, however, the principal concern of the fledgling enterprise is building a business and obtaining the financial resources to enable it to grow. The entrepreneur must develop a clear and compelling business model, that can be communicated to a non-technical investor in a few minutes. This requires a mode of thinking and expression quite different from that commonly used in engineering or scientific discussions. Fortunately, abundant resources are available to help the technologist become a successful entrepreneur. We shall discuss the kinds of assistance that are generally available through local and national programs, and give specific examples based on the activities of the Bay Area Regional Technology Alliance in northern California.

  2. Technical leadership development: Speeding up the process

    International Nuclear Information System (INIS)

    Bilger, W.T.; Shropshire, J.C.; Coleman, S.L.; Collins, R.

    1993-01-01

    This paper describes the Applied Engineering Fundamentals Course, a 14-week course designed for newly hired U.S. Department of Energy (DOE) engineers and scientists who will assume oversight responsibilities at technically complex facilities. This course includes formal education and training, an applications course in the field, and rotational assignments

  3. Final Technical Report and management: NUCLEAR ENGINEERING RECRUITMENT EFFORT

    International Nuclear Information System (INIS)

    Kerrick, Sharon S.; Vincent, Charles D.

    2007-01-01

    This report provides the summary of a project whose purpose was to support the costs of developing a nuclear engineering awareness program, an instruction program for teachers to integrate lessons on nuclear science and technology into their existing curricula, and web sites for the exchange of nuclear engineering career information and classroom materials. The specific objectives of the program were as follows: Objective 1--Increase awareness and interest of nuclear engineering; Objective 2--Instruct Teachers on nuclear topics; Objective 3--Nuclear education programs web-site; Objective 4--Support to university/industry matching grants and reactor sharing; Objective 5--Pilot project; and Objective 6--Nuclear engineering enrollment survey at universities

  4. Architectural Engineers

    DEFF Research Database (Denmark)

    Petersen, Rikke Premer

    engineering is addresses from two perspectives – as an educational response and an occupational constellation. Architecture and engineering are two of the traditional design professions and they frequently meet in the occupational setting, but at educational institutions they remain largely estranged....... The paper builds on a multi-sited study of an architectural engineering program at the Technical University of Denmark and an architectural engineering team within an international engineering consultancy based on Denmark. They are both responding to new tendencies within the building industry where...... the role of engineers and architects increasingly overlap during the design process, but their approaches reflect different perceptions of the consequences. The paper discusses some of the challenges that design education, not only within engineering, is facing today: young designers must be equipped...

  5. Technical management of difference in CEPR nuclear power project

    International Nuclear Information System (INIS)

    Guo Ruiting

    2014-01-01

    The Thesis dissertate the application of technical management of difference in CEPR Nuclear Power Project from EPR technical bases, condition of a nuclear power plant site, engineering and procurement, construction, quality management, schedule management and experience feedback aspects. (author)

  6. Engineering Manpower Bulletin, Number 16.

    Science.gov (United States)

    Engineers Joint Council, New York, NY. Engineering Manpower Commission.

    This bulletin presents the highlights of an evaluation of today's engineering graduates as seen by the managers of engineering, manufacturing and technical marketing in a major electrical equipment manufacturing company. Today's engineer is seen as far more productive than his predecessor. The computer has greatly expanded his productive capacity.…

  7. Engineering Knowledge and Student Development: An Institutional and Pedagogical Critique of Engineering Education

    Science.gov (United States)

    Tang, Xiaofeng

    Educators have recommended the integration of engineering and the liberal arts as a promising educational model to prepare young engineers for global economic, environmental, sociotechnical, and ethical challenges. Drawing upon philosophy of technology, engineering studies, and educational psychology, this dissertation examines diverse visions and strategies for integrating engineering and liberal education and explores their impacts on students' intellectual and moral development. Based on archival research, interviews, and participant observation, the dissertation presents in-depth case studies of three educational initiatives that seek to blend engineering with the humanities, social sciences, and arts: Harvey Mudd College, the Picker Engineering Program at Smith College, and the Programs in Design and Innovation at Rensselaer Polytechnic Institute. The research finds that learning engineering in a liberal arts context increases students' sense of "owning" their education and contributes to their communication, teamwork, and other non-technical professional skills. In addition, opportunities for extensive liberal arts learning in the three cases encourage some students to pursue alternative, less technocentric approaches to engineering. Nevertheless, the case studies suggest that the epistemological differences between the engineering and liberal arts instructors help maintain a technical/social dualism among most students. Furthermore, the dissertation argues a "hidden curriculum," which reinforces the dominant ideology in the engineering profession, persists in the integrated programs and prevents the students from reflecting on the broad social context of engineering and critically examining the assumptions upheld in the engineering profession.

  8. Aristotle and Autism: Reconsidering a Radical Shift to Virtue Ethics in Engineering.

    Science.gov (United States)

    Furey, Heidi

    2017-04-01

    Virtue-based approaches to engineering ethics have recently received considerable attention within the field of engineering education. Proponents of virtue ethics in engineering argue that the approach is practically and pedagogically superior to traditional approaches to engineering ethics, including the study of professional codes of ethics and normative theories of behavior. This paper argues that a virtue-based approach, as interpreted in the current literature, is neither practically or pedagogically effective for a significant subpopulation within engineering: engineers with high functioning autism spectrum disorder (ASD). Because the main argument for adopting a character-based approach is that it could be more successfully applied to engineering than traditional rule-based or algorithmic ethical approaches, this oversight is problematic for the proponents of the virtue-based view. Furthermore, without addressing these concerns, the wide adoption of a virtue-based approach to engineering ethics has the potential to isolate individuals with ASD and to devalue their contributions to moral practice. In the end, this paper gestures towards a way of incorporating important insights from virtue ethics in engineering that would be more inclusive of those with ASD.

  9. Survey of materials and other problems of relevance in safety engineering, and an assessment of their reflection in regulatory guides for conventional and nuclear engineering (1. technical report)

    International Nuclear Information System (INIS)

    Trunk, M.; Herter, K.H.

    1984-01-01

    Survey and assessment of nuclear engineering specifications and regulatory guides (ASME-BPVC Section III, division 1,2 and KTA, BS 5500) with regard to materials, dimensioning and testing for the purpose of showing to what extent available technical codes, regulatory guides and safety codes are useful in preventing failures and defining the safe limit. The other question examined is that of how these codes ought to be brought up to date in order to reflect the latest state of the art in science and technology. (orig./HP) [de

  10. Educating engineering designers for a multidisciplinary future

    DEFF Research Database (Denmark)

    engineering design education. Educating engineering designers today significantly differs from traditional engineering education (McAloone, et.al., 2007). However, a broader view of design activities gains little attention. The project course Product/Service-Systems, which is coupled to the lecture based...... course Product life and Environmental issues at the Technical University of Denmark (DTU) and the master programme Product Development Processes at the Luleå University of Technology (LTU), Sweden, are both curriculums with a broader view than traditional (mechanical) engineering design. Based...... on these two representatives of a Scandinavian approach, the purpose in this presentation is to describe two ways of educating engineering designers to enable them to develop these broader competencies of socio-technical aspects of engineering design. Product Development Processes at LTU A process, called...

  11. Vincent Vuillemin: Consolidating CERN’s technical base

    CERN Multimedia

    2009-01-01

    Former head of the Technical Support Department, Vincent Vuillemin is pursuing his mission as the head of the new Engineering Department. The remodelled department is working towards the resumption of LHC operations, on the Laboratory’s numerous projects and consolidation of the existing facilities. Vincent Vuillemin studies the table spread out on his broad office desk, showing his department’s projects. Red shows top-priority projects, blue is for projects under development and yellow is for future projects. Of course, the top red slot is reserved for the LHC. "Getting the LHC back into service is our absolute top priority," states Vuillemin. Whenever a technical difficulty arose with the LHC project—from defects in the cryogenic distribution line to the manufacturing problems that affected the collimators—the teams of the Technical Support Department (TS), now the Engineering Department (EN), were at the forefront, making u...

  12. Assessing Engineering Education in Sub-Saharan Africa. World Bank Technical Paper Number 197, Africa Technical Department Series.

    Science.gov (United States)

    Zymelman, Manuel, Ed.

    This guide to assessing engineering education in Sub-Saharan Africa consists of three sections, covering: (1) assessment of qualitative and quantitative needs; (2) assessment of the engineering education institution in developing countries; and (3) methods of forecasting demand for engineers; assessment of the efficiency of engineering training…

  13. IMechE engineers' databook

    CERN Document Server

    Matthews, Clifford

    2011-01-01

    A completely revised and expanded fourth edition of this best-selling pocket guide. Engineers' Data Book provides a concise and useful source of up-to-date essential information for the student or practising engineer. Updated, expanded editionEasy to useHandy reference guideCore technical data

  14. Software Engineering Improvement Plan

    Science.gov (United States)

    2006-01-01

    In performance of this task order, bd Systems personnel provided support to the Flight Software Branch and the Software Working Group through multiple tasks related to software engineering improvement and to activities of the independent Technical Authority (iTA) Discipline Technical Warrant Holder (DTWH) for software engineering. To ensure that the products, comments, and recommendations complied with customer requirements and the statement of work, bd Systems personnel maintained close coordination with the customer. These personnel performed work in areas such as update of agency requirements and directives database, software effort estimation, software problem reports, a web-based process asset library, miscellaneous documentation review, software system requirements, issue tracking software survey, systems engineering NPR, and project-related reviews. This report contains a summary of the work performed and the accomplishments in each of these areas.

  15. Foundations for a new type of Design-Engineers

    DEFF Research Database (Denmark)

    Jørgensen, Ulrik; Brodersen, Søsser; Lindegaard, Hanne

    2011-01-01

    almost equally in the curriculum: natural and technical sciences, design synthesis and socio-technical analysis. Combined with an integration and co-ordination of disciplines, a series of projects providing a progression of challenges to the students⿿ learning, and a focus on the outcomes of the learning...... processes of competences needed in design engineering, the curriculum represents a radical innovation in engineering curriculum. The paper describes the background as well as the foundational elements constituting the educational program and presents an assessment of the key factors that has made it attract......Since 2002 a new design-engineering education has been organized at the Technical University of Denmark. It fulfils most of the requirements in the CDIO concept but builds in addition on a change in what is considered core disciplines in engineering as three fields of knowledge are represented...

  16. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 25: The technical communications practices of British aerospace engineers and scientists: Results of the phase 4 RAeS mail survey

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1994-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of British aerospace engineers and scientists.

  17. TECHNICAL COORDINATION

    CERN Multimedia

    Austin Ball

    2013-01-01

      Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

  18. Energy Economic Data Base (EEDB) Program. Technical Reference Book

    International Nuclear Information System (INIS)

    Allen, R.E.; Benedict, R.G.; Hodson, J.S.

    1983-09-01

    Purpose of the program is to develop current technical and cost information for nuclear and comparison electric power generating stations. Purpose of this Technical Reference Book is to provide the current technical design bases for each of the technical data models updated in the Sixth Update (1983). It contains a set of detailed system design descriptions for these technical data models, which are supplemented with engineering drawings. The system design descriptions reflect regulatory and industry practice and experience for nuclear and coal-fired power generating stations that are current for January 1, 1983

  19. Routledge French technical dictionary

    CERN Document Server

    1994-01-01

    The French-English volume of this highly acclaimed set consists of some 100,000 keywords in both French and English, drawn from the whole range of modern applied science and technical terminology. Covers over 70 subject areas, from engineering and chemistry to packaging, transportation, data processing and much more.

  20. FY 2002 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Fowler, B. A. (Compiler)

    2003-01-01

    This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 2002. It also includes papers of MSFC contractors. The information in this TM may be of value to the scientific and engineering community in determining what information has been published and what is available.

  1. Stirling engine alternatives for the terrestrial solar application

    Science.gov (United States)

    Stearns, J.

    1985-01-01

    The first phase of the present study of Stirling engine alternatives for solar thermal-electric generation has been completed. Development risk levels are considered to be high for all engines evaluated. Free-piston type and Ringbom-type Stirling engine-alternators are not yet developed for the 25 to 50-kW electrical power range, although smaller machines have demonstrated the inherent robustness of the machines. Kinematic-type Stirling engines are presently achieving a 3500 hr lifetime or longer on critical components, and lifetime must still be further extended for the solar application. Operational and technical characteristics of all types of Stirling engines have been reviewed with engine developers. Technical work of merit in progress in each engine development organization should be recognized and supported in an appropriate manner.

  2. TWRS technical baseline database manager definition document

    International Nuclear Information System (INIS)

    Acree, C.D.

    1997-01-01

    This document serves as a guide for using the TWRS Technical Baseline Database Management Systems Engineering (SE) support tool in performing SE activities for the Tank Waste Remediation System (TWRS). This document will provide a consistent interpretation of the relationships between the TWRS Technical Baseline Database Management software and the present TWRS SE practices. The Database Manager currently utilized is the RDD-1000 System manufactured by the Ascent Logic Corporation. In other documents, the term RDD-1000 may be used interchangeably with TWRS Technical Baseline Database Manager

  3. The Complex Dynamics of Student Engagement in Novel Engineering Design Activities

    Science.gov (United States)

    McCormick, Mary

    In engineering design, making sense of "messy," design situations is at the heart of the discipline (Schon, 1983); engineers in practice bring structure to design situations by organizing, negotiating, and coordinating multiple aspects (Bucciarelli, 1994; Stevens, Johri, & O'Connor, 2014). In classroom settings, however, students are more often given well-defined, content-focused engineering tasks (Jonassen, 2014). These tasks are based on the assumption that elementary students are unable to grapple with the complexity or open-endedness of engineering design (Crismond & Adams, 2012). The data I present in this dissertation suggest the opposite. I show that students are not only able to make sense of, or frame (Goffman, 1974), complex design situations, but that their framings dynamically involve their nascent abilities for engineering design. The context of this work is Novel Engineering, a larger research project that explores using children's literature as an access point for engineering design. Novel Engineering activities are inherently messy: there are characters with needs, settings with implicit constraints, and rich design situations. In a series of three studies, I show how students' framings of Novel Engineering design activities involve their reasoning and acting as beginning engineers. In the first study, I show two students whose caring for the story characters contributes to their stability in framing the task: they identify the needs of their fictional clients and iteratively design a solution to meet their clients' needs. In the second, I show how students' shifting and negotiating framings influence their engineering assumptions and evaluation criteria. In the third, I show how students' coordinating framings involve navigating a design process to meet clients' needs, classroom expectations, and technical requirements. Collectively, these studies contribute to literature by documenting students' productive beginnings in engineering design. The

  4. The key to technical translation, v.1 concept specification

    CERN Document Server

    Hann, Michael

    1992-01-01

    This handbook for German/English/German technical translators at all levels from student to professional covers the root terminologies of the spectrum of scientific and engineering fields. The work is designed to give technical translators direct insight into the main error sources occurring in their profession, especially those resulting from a poor understanding of the subject matter and the usage of particular terms to designate different concepts in different branches of technology. The style is easy to read and suitable for nonnative English speakers and translators with no engineering ex

  5. The key to technical translation, v.2 terminology/lexicography

    CERN Document Server

    Hann, Michael

    1992-01-01

    This handbook for German/English/German technical translators at all levels from student to professional covers the root terminologies of the spectrum of scientific and engineering fields. The work is designed to give technical translators direct insight into the main error sources occurring in their profession, especially those resulting from a poor understanding of the subject matter and the usage of particular terms to designate different concepts in different branches of technology. The style is easy to read and suitable for nonnative English speakers and translators with no engineering ex

  6. FY 2005 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Narmore, K. A. (Compiler)

    2007-01-01

    This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by Marshall Space Flight Center (MSFC) personnel in FY 2005. It also includes papers of MSFC contractors. The information in this TM may be of value to the scientific and engineering community in determining what information has been published and what is available.

  7. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 33: The technical communications practices of US aerospace engineers and scientists: Results of the phase 1 AIAA mail survey

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1995-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of U.S. aerospace engineers and scientists who are members of the American Institute of Aeronautics and Astronautics (AIAA).

  8. Technical presentation

    CERN Multimedia

    GS Department

    2010-01-01

    10 March 2010 DYNEOS 10:00 – 12:00 - Main Building, Room B, 61-1-009 Dyneos AG is active in the fields of photonics, laser and high-precision positioning. Our highly qualified engineer team has more than 30 years of experience in electro-optical solutions sales. The engineers are supported by a technical and administrative team. We are focused on the Swiss market and represent six suppliers (Coherent, PI Physik Instrumente, SIOS, Nanonics Imaging, APE, Ekspla) in order to give a qualified sales and service support to our customers. Our products are dedicated to the research field as well as to industry. In addition to standard catalog products, we offer custom designs to fulfill the specific needs of OEM customers or specific applications.

  9. The Radical Flank Effect and Cross-occupational Collaboration for Technology Development during a Power Shift

    Science.gov (United States)

    Truelove, Emily; Kellogg, Katherine C.

    2016-01-01

    This 12-month ethnographic study of an early entrant into the U.S. car-sharing industry demonstrates that when an organization shifts its focus from developing radical new technology to incrementally improving this technology, the shift may spark an internal power struggle between the dominant engineering group and a challenger occupational group such as the marketing group. Analyzing 42 projects in two time periods that required collaboration between engineering and marketing during such a shift, we show how cross-occupational collaboration under these conditions can be facilitated by a radical flank threat, through which the bargaining power of moderates is strengthened by the presence of a more-radical group. In the face of a strong threat by radical members of a challenger occupational group, moderate members of the dominant engineering group may change their perceptions of their power to resist challengers’ demands and begin to distinguish between the goals of radical versus more-moderate challengers. To maintain as much power as possible and prevent the more-dramatic change in engineering occupational goals demanded by radical challengers, moderate engineers may build a coalition with moderate challengers and collaborate for incremental technology development. PMID:28424533

  10. The Radical Flank Effect and Cross-occupational Collaboration for Technology Development during a Power Shift.

    Science.gov (United States)

    Truelove, Emily; Kellogg, Katherine C

    2016-12-01

    This 12-month ethnographic study of an early entrant into the U.S. car-sharing industry demonstrates that when an organization shifts its focus from developing radical new technology to incrementally improving this technology, the shift may spark an internal power struggle between the dominant engineering group and a challenger occupational group such as the marketing group. Analyzing 42 projects in two time periods that required collaboration between engineering and marketing during such a shift, we show how cross-occupational collaboration under these conditions can be facilitated by a radical flank threat, through which the bargaining power of moderates is strengthened by the presence of a more-radical group. In the face of a strong threat by radical members of a challenger occupational group, moderate members of the dominant engineering group may change their perceptions of their power to resist challengers' demands and begin to distinguish between the goals of radical versus more-moderate challengers. To maintain as much power as possible and prevent the more-dramatic change in engineering occupational goals demanded by radical challengers, moderate engineers may build a coalition with moderate challengers and collaborate for incremental technology development.

  11. A technical and financial analysis of two recuperated, reciprocating engine driven power plants. Part 1: Thermodynamic analysis

    International Nuclear Information System (INIS)

    Orbaiz, Pedro Jose; Brear, Michael J.

    2014-01-01

    Highlights: • A thermodynamic analysis of two recuperated ICE plants is undertaken. • The overall plant efficiency and CO 2 emissions are analysed. • Chemical recuperation without a secondary heat source is unlikely. • Using a renewable secondary heat source reduces the CO 2 emission of the plant. - Abstract: This paper is the first of a two part study that analyses the technical and financial performance of particular, recuperated engine systems. This first paper presents a thermodynamic study of two systems. The first system involves the chemical recuperation of a reciprocating, spark ignited, internal combustion engine using only the waste heat of the engine to power a steam–methane reformer. The performance of this system is evaluated for different coolant loads and steam–methane ratios. The second system is a so-called ’hybrid’ in which not only the waste heat of the engine is used, but also a secondary heat source – the combustion of biomass. The effects of the reformer’s temperature and the steam–methane ratio on the system performance are analysed. These analyses show that the potential efficiency improvement obtained when using only the engine waste heat to power the recuperation is marginal. However, results for the hybrid show that although the overall efficiency of the plant, defined in terms of the energy from both the methane and biomass, is similar to that of the conventional, methane fuelled engine, the efficiency of the conversion of the biomass fuel energy to work output appears to be higher than for other biomass fuelled technologies currently in use. Further, in the ideal limit of a fully renewable biomass fuel, the burning of biomass does not contribute to the net CO 2 emissions, and the CO 2 emission reduction for this second plant can be considerable. Indeed, its implementation on larger internal combustion engine power plants, which have efficiencies of around 45–50%, could result in CO 2 emissions that are as much as

  12. Environmental engineering education: examples of accreditation and quality assurance

    Science.gov (United States)

    Caporali, E.; Catelani, M.; Manfrida, G.; Valdiserri, J.

    2013-12-01

    Environmental engineers respond to the challenges posed by a growing population, intensifying land-use pressures, natural resources exploitation as well as rapidly evolving technology. The environmental engineer must develop technically sound solutions within the framework of maintaining or improving environmental quality, complying with public policy, and optimizing the utilization of resources. The engineer provides system and component design, serves as a technical advisor in policy making and legal deliberations, develops management schemes for resources, and provides technical evaluations of systems. Through the current work of environmental engineers, individuals and businesses are able to understand how to coordinate society's interaction with the environment. There will always be a need for engineers who are able to integrate the latest technologies into systems to respond to the needs for food and energy while protecting natural resources. In general, the environment-related challenges and problems need to be faced at global level, leading to the globalization of the engineering profession which requires not only the capacity to communicate in a common technical language, but also the assurance of an adequate and common level of technical competences, knowledge and understanding. In this framework, the Europe-based EUR ACE (European Accreditation of Engineering Programmes) system, currently operated by ENAEE - European Network for Accreditation of Engineering Education can represent the proper framework and accreditation system in order to provide a set of measures to assess the quality of engineering degree programmes in Europe and abroad. The application of the accreditation model EUR-ACE, and of the National Italian Degree Courses Accreditation System, promoted by the Italian National Agency for the Evaluation of Universities and Research Institutes (ANVUR), to the Environmental Engineering Degree Courses at the University of Firenze is presented. In

  13. Electrical and Electronics Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Electrical and Electronics Technical Team’s (EETT's) mission is to enable cost-effective, smaller, lighter, and efficient power electronics and electric motors for electric traction drive systems (ETDSs) while maintaining performance of internal combustion engine (ICE)-based vehicles. The EETT also identifies technology gaps, establishes R&D targets, develops a roadmap to achieve technical targets and goals, and evaluates the R&D progress toward meeting the established R&D targets and goals.

  14. Development of TRITN : In-house technical information network of Technical Research Institute in The Chugoku Electric Power Co., Inc.

    Science.gov (United States)

    Ebara, Hisao

    With the increase in information amount, progress in information network, diversified technology and change in in-house organization the Technical Research Institute has necessitated to shift the conventional technical database processing by use of personal computers into new system promised for future use. It enables to; provide classification system which meets the needs of the institute; execute distributed processing using workstations; make the low cost processing using commercial softwares; make networks using LAN, WAN personal computer communication, and provide primary materials (text data) on facsimiles using optical disks. Such features are those of technical information database system "TRITN" which is available to any persons and at any time. This paper describes how TRITN was developed and the system outline.

  15. Technical assistance contractor Management Plan. Final [report

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins & Beckwith Agra, Inc. (SHB Agra), and Geraghty & Miller, Inc. (G&M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC`s groundwater technical breadth and depth, so G&M was brought in to augment the team`s capabilities. The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC`s management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls.

  16. Teaching technical writing in multilingual contexts: a meta-analysis

    NARCIS (Netherlands)

    Winberg, Christine; van der Geest, Thea; Lehman, Barbara; Nduna, Joyce

    2010-01-01

    Teachers of technical and professional writing in Science, Engineering and Technology (SET) Programmes need to understand the particular needs and social contexts of students for whom English is not a first language. The focus of this paper is on technical writing, and the paper presents the

  17. Understanding the technical content of requirements in specification document

    DEFF Research Database (Denmark)

    Sudin, Mohd Nizam Bin; Ahmed-Kristensen, Saeema

    2011-01-01

    development process, is essential to be devised in advance. To achieve this aim, understanding how to formulate a good requirement is necessary and it is only possible if design engineers understand the technical content of a requirement. In aiming to understand the technical content of a requirement...

  18. Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Waits, J. E. Turner (Compiler)

    2001-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 2000. It also includes papers of MSFC contractors. After being announced in STAR, all the NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  19. Anthropometric changes and fluid shifts

    Science.gov (United States)

    Thornton, W. E.; Hoffler, G. W.; Rummel, J. A.

    1974-01-01

    Several observations of body size, shape, posture, and configuration were made to document changes resulting from direct effects of weightlessness during the Skylab 4 mission. After the crewmen were placed in orbit, a number of anatomical and anthropometric changes occurred including a straightening of the thoracolumbar spine, a general decrease in truncal girth, and an increase in height. By the time of the earliest in-flight measurement on mission day 3, all crewmen had lost more than two liters of extravascular fluid from the calf and thigh. The puffy facies, the bird legs effect, the engorgement of upper body veins, and the reduced volume of lower body veins were all documented with photographs. Center-of-mass measurements confirmed a fluid shift cephalad. This shift remained throughout the mission until recovery, when a sharp reversal occurred; a major portion of the reversal was completed in a few hours. The anatomical changes are of considerable scientific interest and of import to the human factors design engineer, but the shifts of blood and extravascular fluid are of more consequence. It is hypothesized that the driving force for the fluid shift is the intrinsic and unopposed lower limb elasticity that forces venous blood and then other fluid cephalad.

  20. Expose Mechanical Engineering Students to Biomechanics Topics

    Science.gov (United States)

    Shen, Hui

    2011-01-01

    To adapt the focus of engineering education to emerging new industries and technologies nationwide and in the local area, a biomechanics module has been developed and incorporated into a mechanical engineering technical elective course to expose mechanical engineering students at ONU (Ohio Northern University) to the biomedical engineering topics.…

  1. Contract engineers cut costs, and flexibility

    International Nuclear Information System (INIS)

    Bhargava, V.M.

    1991-01-01

    Today's rapid expansion of technology is an important reason for considering hiring contract engineering labor for your power plant because technical specialization is an important aspect of the contract engineering industry. This paper reports that another reason is addressing peak work loads. Any amount of technical assistance is available to assist in meeting schedules. Although a typical human resources department of a utility or architect/engineer may contain a few hundred active resumes, a contract engineering firm may have upwards of 40,000 resumes on file from all parts of the country. Because contract workers know that contract agencies keep abreast of client needs, they are more apt to forward updated resumes to such agencies. Used properly, a contract engineering company's services will augment the efforts of a human resources group and, in the case of some smaller companies, actually take the place of all internal recruiting efforts

  2. A practitioner’s experiences operationalizing Resilience Engineering

    International Nuclear Information System (INIS)

    Lay, E.; Branlat, M.; Woods, Z.

    2015-01-01

    Resilience Engineering (RE) is a reframed perspective. This begs the question, “How to operationalize a shift in perspective?” We share strategies, tactics, experiences, and observations from implementing Resilience Engineering in power generation equipment maintenance. Use of Resilience Engineering principles shifts focus to the future, to systems, and to how people really work (not the idealized version of work). We more effectively shape outcomes as we pay attention to what’s coming, looking for signs we’re outside normal work or running out of margins that enable us to adapt and respond. Use of these principles opens new possibilities grounded in theoretical fields of biology, cognitive and system sciences (understand Cartesian views of the world work well for machines but not for people) and underlain by core principles (e.g., people fundamentally want to do a good job, actions taken make sense at the time, and system factors are tremendously influential on outcomes). This paper presents a practitioner’s account of a Resilience Engineering approach in the context of power plant maintenance. The paper will describe how the introduction of RE principles was made possible through supporting/fostering shifts in perspective and gaining buy-in at various levels of the organization. - Highlights: • Resilience Engineering is a shifted perspective as compared to a new program. • RE is grounded in fields of biology, cognitive and system sciences. • We share strategies, tactics, experiences, and observations for implementing RE. • We used a middle out approach

  3. Practical and Efficient Searching in Proteomics: A Cross Engine Comparison

    Science.gov (United States)

    Paulo, Joao A.

    2014-01-01

    Background Analysis of large datasets produced by mass spectrometry-based proteomics relies on database search algorithms to sequence peptides and identify proteins. Several such scoring methods are available, each based on different statistical foundations and thereby not producing identical results. Here, the aim is to compare peptide and protein identifications using multiple search engines and examine the additional proteins gained by increasing the number of technical replicate analyses. Methods A HeLa whole cell lysate was analyzed on an Orbitrap mass spectrometer for 10 technical replicates. The data were combined and searched using Mascot, SEQUEST, and Andromeda. Comparisons were made of peptide and protein identifications among the search engines. In addition, searches using each engine were performed with incrementing number of technical replicates. Results The number and identity of peptides and proteins differed across search engines. For all three search engines, the differences in proteins identifications were greater than the differences in peptide identifications indicating that the major source of the disparity may be at the protein inference grouping level. The data also revealed that analysis of 2 technical replicates can increase protein identifications by up to 10-15%, while a third replicate results in an additional 4-5%. Conclusions The data emphasize two practical methods of increasing the robustness of mass spectrometry data analysis. The data show that 1) using multiple search engines can expand the number of identified proteins (union) and validate protein identifications (intersection), and 2) analysis of 2 or 3 technical replicates can substantially expand protein identifications. Moreover, information can be extracted from a dataset by performing database searching with different engines and performing technical repeats, which requires no additional sample preparation and effectively utilizes research time and effort. PMID:25346847

  4. Can and Should Social Competence be Taught to Engineers?

    Directory of Open Access Journals (Sweden)

    Pia Helena Lappalainen

    2011-10-01

    Full Text Available The traditional focus in engineering syllabi on technical abilities has been well substantiated by the types of knowledge and skills required in industrial processes. However, the emerging requirements in industrial operating environments necessitate a more personal configuration of competencies facilitating both intrapersonal and interpersonal processes at workplace. The concomitant reform of engineering education to incorporate social competence into the technical education calls for a revision of pedagogy, as the traditional instruments applied in the dissemination of substance knowledge and technical skills provide little support for leveraging students’ social skills. This article discusses the learnability of socio-emotional abilities and reviews their most fundamental and pertinent skills. The results from a quantitative, empirical research conducted in engineering industries to identify predictors of social competence are reported and the implications on engineering pedagogy examined. The proposed methodology for teaching social skills in the engineering classroom setup constitutes collaborative learning, self-management techniques, and teacher immediacy.

  5. Predicting technology operational availability using technical maturity assessment

    International Nuclear Information System (INIS)

    Kenley, C.R.; Creque, T.R.

    1998-01-01

    A technical maturity assessment method was performed by systems engineers in collaboration with an advisory panel composed of team members from different Department of Energy sites and from different engineering and science disciplines. Various stabilization technologies were assessed annually as to their relative maturity and availability for use in stabilizing nuclear materials. After three years of assessments, several of the technologies are now components of operational systems. A regression analysis of the historical assessments was performed, and it was concluded that the numerical technical maturity score produced by a team of experts can provide a powerful predictor of the time remaining until the operational application of technologies

  6. CHP from Updraft Gasifier and Stirling Engine

    DEFF Research Database (Denmark)

    Jensen, N.; Werling, J.; Carlsen, Henrik

    2002-01-01

    The combination of thermal gasification with a Stirling engine is an interesting concept for use in small combined heat and power plants based on biomass. By combining the two technologies a synergism can potentially be achieved. Technical problems, e.g. gas cleaning and fouling of the Stirling...... engine heat exchanger, can be eliminated and the overall electric efficiency of the system can be improved. At the Technical University of Denmark a Stirling engine fueled by gasification gas has been developed. In this engine the combustion system and the geometry of the hot heat exchanger...... of the Stirling engine has been adapted to the use of a gas with a low specific energy content and a high content of tar and particles. In the spring of 2001 a demonstration plant has been built in the western part of Denmark where this Stirling engine is combined with an updraft gasifier. A mathematical...

  7. Fusion Engineering Device design description

    International Nuclear Information System (INIS)

    Flanagan, C.A.; Steiner, D.; Smith, G.E.

    1981-12-01

    The US Magnetic Fusion Engineering Act of 1980 calls for the operation of a Fusion Engineering Device (FED) by 1990. It is the intent of the Act that the FED, in combination with other testing facilities, will establish the engineering feasibility of magnetic fusion energy. During 1981, the Fusion Engineering Design Center (FEDC), under the guidance of a Technical Management Board (TMB), developed a baseline design for the FED. This design is summarized herein

  8. Fusion engineering device design description

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, C.A.; Steiner, D.; Smith, G.E.

    1981-12-01

    The US Magnetic Fusion Engineering Act of 1980 calls for the operation of a Fusion Engineering Device (FED) by 1990. It is the intent of the Act that the FED, in combination with other testing facilities, will establish the engineering feasibility of magnetic fusion energy. During 1981, the Fusion Engineering Design Center (FEDC), under the guidance of a Technical Management Board (TMB), developed a baseline design for the FED. This design is summarized herein.

  9. Fusion engineering device design description

    International Nuclear Information System (INIS)

    Flanagan, C.A.; Steiner, D.; Smith, G.E.

    1981-12-01

    The US Magnetic Fusion Engineering Act of 1980 calls for the operation of a Fusion Engineering Device (FED) by 1990. It is the intent of the Act that the FED, in combination with other testing facilities, will establish the engineering feasibility of magnetic fusion energy. During 1981, the Fusion Engineering Design Center (FEDC), under the guidance of a Technical Management Board (TMB), developed a baseline design for the FED. This design is summarized herein

  10. Re-Engineering Vocational and Technical Education for Sustainable ...

    African Journals Online (AJOL)

    Using the case of North Central Geo-Political Zone of Nigeria, this study interrogates the nexus between vocational and technical education (VTE) and sustainable development. Specific attention is put on provision and attainment of basic skills on one hand and job creation, self-employment, utilization of locally available ...

  11. The Migration of Technical Workers

    DEFF Research Database (Denmark)

    Dahl, Michael S.; Sorenson, Olav

    2010-01-01

    Using panel data on the Danish population, we estimated the revealed preferences of scientists and engineers for the places in which they choose to work. Our results indicate that these technical workers exhibit substantial sensitivity to differences in wages but that they have even stronger...

  12. Physical foundations of technical acoustics

    CERN Document Server

    Malecki, I

    1969-01-01

    Physical Foundations of Technical Acoustics discusses theoretical foundations of acoustical engineering. It is not so much a technical compendium as a systematic statement of physical laws so conceived that technologists might find in it all the information they need to become acquainted with the physical meaning and mathematical expression of phenomena they encounter in their work. To facilitate the acquirement of notions, which lie beyond a layman's grasp, the plan of narration adopted consists in beginning with the simplest idealized cases and then gradually moving on to the truest possibl

  13. ITER co-ordinated technical activities

    International Nuclear Information System (INIS)

    2001-01-01

    As agreed upon between the ITER Engineering Design Activities (EDA) Parties 'Co-ordinated Technical Activities' (CTA) means technical activities which are deemed necessary to maintain the integrity of the international project, so as to prepare for the ITER joint implementation. The scope of these activities includes design adaptation to the specific site conditions, safety analysis and licensing preparation that are based on specific site offers, evaluation of cost and construction schedule, preparation of procurement documents and other issues raised by the Parties collectively, whilst assuring the coherence of the ITER project including design control

  14. High School Graphics Experience Influencing the Self-Efficacy of First-Year Engineering Students in an Introductory Engineering Graphics Course

    Science.gov (United States)

    Metraglia, Riccardo; Villa, Valerio; Baronio, Gabriele; Adamini, Riccardo

    2015-01-01

    Today's students enter engineering colleges with different technical backgrounds and prior graphics experience. This may due to their high school of provenience, which can be technical or non-technical. The prior experience affects students' ability in learning and hence their motivation and self-efficacy beliefs. This study intended to evaluate…

  15. Bildung and identity development in engineering education

    DEFF Research Database (Denmark)

    Du, Xiangyun

    2006-01-01

    a social context. The analysis of empirical data shows that studying engineering involves not only the mastery of scientific knowledge and technical skills, but also learning the language, established practices, beliefs, values, and norms in the engineering culture, and learning to become an engineer...

  16. Opening remarks: regulatory initiatives toward improved technical specifications

    International Nuclear Information System (INIS)

    Edison, G.E.

    1985-01-01

    In order to deal with the numerous problems that have evolved over the years with nuclear power plant technical specifications, the Nuclear Regulatory Commission has undertaken some initiatives for improvement: 1) new operating licenses, 2) change to existing operating reactor technical specifications, 3) a broad-scoped reconsideration of the content of technical specifications, and 4) rule changes. It is believed that reliability and risk assessment techniques can be used in conjunction with manufacturer's recommendations and engineering judgment to better define the appropriate scope and depth for technical specification resulting in focusing attention on high risk-worth systems and avoidance of plant shutdown transients both intentionally and unintentionally through provisions of technical specifications

  17. Creating technical heritage object replicas in a virtual environment

    Science.gov (United States)

    Egorova, Olga; Shcherbinin, Dmitry

    2016-03-01

    The paper presents innovative informatics methods for creating virtual technical heritage replicas, which are of significant scientific and practical importance not only to researchers but to the public in general. By performing 3D modeling and animation of aircrafts, spaceships, architectural-engineering buildings, and other technical objects, the process of learning is achieved while promoting the preservation of the replicas for future generations. Modern approaches based on the wide usage of computer technologies attract a greater number of young people to explore the history of science and technology and renew their interest in the field of mechanical engineering.

  18. Fuel Element Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Burley, H.H. [ed.

    1956-08-01

    It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

  19. Technical reference book for the Energy Economic Data Base (EEDB) Program

    International Nuclear Information System (INIS)

    Allen, R.E.; Benedict, R.G.; Hodson, J.S.

    1984-09-01

    The Energy Economic Data Base (EEDB) Program is sponsored by the US Department of Energy (DOE) for the purpose of developing current technical and cost information for nuclear and comparison electric power generating stations. The EEDB contains a variety of nuclear and coal-fired power plant technical data models. Each of these data models is a complete and detailed conceptual design for a single unit, commercial, steam electric, power generating station located on a standard hypothetical Middletown site. A major effort for the Sixth Update (1983) has been the updating of the system design descriptions and selected engineering drawings for the technical data models. This update took the form of revising and expanding the system design descriptions and engineering drawings contained in the Base Data Studies, to include the technical information developed and recorded in the first five EEDB updates. The results of the update effort are contained in this EEDB Program Technical Reference Book

  20. Journal of transportation engineering

    National Research Council Canada - National Science Library

    1983-01-01

    The Journal of Transportation Engineering contains technical and professional articles on the planning, design, construction, maintenance, and operation of air, highway, rail, and urban transportation...

  1. Tissue engineering skin: a paradigm shift in wound care.

    Science.gov (United States)

    Mason, C

    2005-12-01

    Tissue-engineered skin for the treatment of burns and ulcers is a clinical success, but making it commercially viable is more problematic. This article examines the industry, its techniques and suggests the way forward.

  2. Master of Engineering Energy Systems Engineering Program: Smart Campus Energy Systems Demonstration DE-SC0005523

    Energy Technology Data Exchange (ETDEWEB)

    Dodge, Martha [Lehigh Univ., Bethlehem, PA (United States); Coulter, John [Lehigh Univ., Bethlehem, PA (United States)

    2014-09-25

    Program Purpose and Position: The mission of the Master of Engineering in Energy Systems Engineering program is to invigorate the pipeline of new engineering graduates interested in energy oriented careers and thus produce a new generation of technical leaders for the energy and power industries. Over the next decade, nearly 50% of the skilled workers and technical leaders in the gas and electric utility industries will retire -- a much larger void than the current available and qualified professionals could fill [CEWD, 2012 survey]. The Masters of Engineering in Energy System Engineering program provides an opportunity for cross-discipline education for graduates interested in a career in the energy industry. It focuses on electric power and the challenges and opportunities to develop a sustainable, reliable and resilient system that meets human needs in an increasingly sustainable manner through the use of environmentally sound energy resources and delivery. Both graduates and employers benefit from a well-trained professional workforce that is ready to hit the road running and be immediately productive in meeting these challenges, through this innovative and unique program.

  3. FY 2004 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Fowler, B. A. (Compiler)

    2006-01-01

    This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by Marshall Space Flight Center (MSFC) personnel FY 2004. It also includes papers of MSFC contractors. After being announced in STAR, all NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this TM maybe of value to the scientific and engineering community in determining what information has been published and what is available.

  4. FY 2001 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Waits, J. E. Turner (Compiler)

    2002-01-01

    This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 2001. It also includes papers of MSFC contractors. After being announced in STAR, all NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this TM may be of value to the scientific and engineering community in determining what information has been published and what is available.

  5. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report 6: The relationship between the use of US government technical reports by US aerospace engineers and scientists and selected institutional and sociometric variables. Ph.D. Thesis - Indiana Univ., Nov. 1990 No. 6

    Science.gov (United States)

    Pinelli, Thomas E.

    1991-01-01

    The relationship between the use of U.S. government technical reports by U.S. aerospace engineers and scientists and selected institutional and sociometric variables was investigated. The methodology used for this study was survey research. Data were collected by means of a self-administered mail questionnaire. The approximately 34,000 members of the American Institute of Aeronautics and Astronauts (AIAA) served as the study population. The response rate for the survey was 70 percent. A dependent relationship was found to exist between the use of U.S. government technical reports and three of the institutional variables (academic preparation, years of professional aerospace work experience, and technical discipline). The use of U.S. government technical reports was found to be independent of all of the sociometric variables. The institutional variables best explain the use of U.S. government technical reports by U.S. aerospace engineers and scientists.

  6. FORMED: Bringing Formal Methods to the Engineering Desktop

    Science.gov (United States)

    2016-02-01

    FORMED: BRINGING FORMAL METHODS TO THE ENGINEERING DESKTOP BAE SYSTEMS FEBRUARY 2016 FINAL TECHNICAL REPORT APPROVED FOR PUBLIC RELEASE...This report is published in the interest of scientific and technical information exchange, and its publication does not constitute the Government’s...BRINGING FORMAL METHODS TO THE ENGINEERING DESKTOP 5a. CONTRACT NUMBER FA8750-14-C-0024 5b. GRANT NUMBER N/A 5c. PROGRAM ELEMENT NUMBER 63781D

  7. Reliability and safety engineering

    CERN Document Server

    Verma, Ajit Kumar; Karanki, Durga Rao

    2016-01-01

    Reliability and safety are core issues that must be addressed throughout the life cycle of engineering systems. Reliability and Safety Engineering presents an overview of the basic concepts, together with simple and practical illustrations. The authors present reliability terminology in various engineering fields, viz.,electronics engineering, software engineering, mechanical engineering, structural engineering and power systems engineering. The book describes the latest applications in the area of probabilistic safety assessment, such as technical specification optimization, risk monitoring and risk informed in-service inspection. Reliability and safety studies must, inevitably, deal with uncertainty, so the book includes uncertainty propagation methods: Monte Carlo simulation, fuzzy arithmetic, Dempster-Shafer theory and probability bounds. Reliability and Safety Engineering also highlights advances in system reliability and safety assessment including dynamic system modeling and uncertainty management. Cas...

  8. Configuration management program plan for Hanford site systems engineering

    International Nuclear Information System (INIS)

    Hoffman, A.G.

    1994-01-01

    This plan establishes the integrated configuration management program for the evolving technical baseline developed through the systems engineering process. This configuration management program aligns with the criteria identified in the DOE Standard, DOE-STD-1073-93. Included are specific requirements for control of the systems engineering RDD-100 database, and electronic data incorporated in the database that establishes the Hanford site technical baseline

  9. FY 1997 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Waits, J. E. Turner (Compiler)

    1998-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY97. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  10. Expert Systems as Tools for Technical Communicators.

    Science.gov (United States)

    Grider, Daryl A.

    1994-01-01

    Discusses expertise, what an expert system is, what an expert system shell is, what expert systems can and cannot do, knowledge engineering and technical communicators, and planning and managing expert system projects. (SR)

  11. 48 CFR 227.7107 - Contracts for architect-engineer services.

    Science.gov (United States)

    2010-10-01

    ...-engineer services. 227.7107 Section 227.7107 Federal Acquisition Regulations System DEFENSE ACQUISITION... Rights in Technical Data 227.7107 Contracts for architect-engineer services. This section sets forth... of construction and architect-engineer services. ...

  12. THE CONCEPT OF INTEGRATED ENGINEERING AND BUSINESS (EB EDUCATION SYSTEM

    Directory of Open Access Journals (Sweden)

    Michał Charlak

    2013-12-01

    Full Text Available In our approach to engineering and business education system an engineer is a man working as creator and user of technical products. We stress that the process of understanding and gaining knowledge of technical reality and creativity of engineers are the essential for EB concept . Next, we describe briefly three perspectives for building the system of innovative product origination as a basis for EB system: 1 designer’s perspective; 2 business perspective. 3 consumer perspective.

  13. Necessity and Contention of Education on Engineer Ethics

    Science.gov (United States)

    Takeda, Kunihiko; Ishikawa, Tomoyuki

    Using examples of major accidents caused by technical technology are effective when teaching engineering ethics in undergraduate courses because almost all students have had no actual experience in technical problems or accidents in their lives. The typical accidents that have been selected in the past for this purpose by lecturers are limited in Japanese colleges or in textbooks. Some examples are the Minamata disease, the Kanemi oil PCB contamination, the space shuttle “Challenger” accident, the Ford “Pinto” design problem, Mitsubishi Motor's scandal and the unclear power plant accident at Tokai. However, it is difficult to decide whether or not these typical accidents are suitable for the teaching of engineering ethics. The responsibility of an engineer in Japan is strictly limited because he has no authority to finally decide upon the problem of ethics even if the item is purely technical and he is the best person to make the decision. The reason is discussed focusing on 1) the concept of the “profession” of medical doctors and engineers and 2) the relationships between the treatment, position, honor and responsibility of engineers in Japanese society.

  14. Training Engineers to Write: Old Assumptions and New Directions.

    Science.gov (United States)

    Schillaci, William C.

    1996-01-01

    States that universities and engineering firms do not generally train engineers in business technical writing, although firms benefit from having engineers who can write clear descriptions of their work. Suggests a program to promote writing skills of engineers and engineering students with limited English skills that involves clear, logical lists…

  15. Abstracts of the 17. world congress of the International Commission of Agriculture and Biosystems Engineering (CIGR) : sustainable biosystems through engineering

    Energy Technology Data Exchange (ETDEWEB)

    Savoie, P.; Villeneuve, J.; Morisette, R. [Agriculture and Agri-Food Canada, Quebec City, PQ (Canada). Soils and Crops Research and Development Centre] (eds.)

    2010-07-01

    This international conference provided a forum to discuss methods to produce agricultural products more efficiently through improvements in engineering and technology. It was attended by engineers and scientists working from different perspectives on biosystems. Beyond food, farms and forests can provide fibre, bio-products and renewable energy. Seven sections of CIGR were organized in the following technical sessions: (1) land and water engineering, (2) farm buildings, equipment, structures and environment, (3) equipment engineering for plants, (4) energy in agriculture, (5) management, ergonomics and systems engineering, (6) post harvest technology and process engineering, and (7) information systems. The Canadian Society of Bioengineering (CSBE) merged its technical program within the 7 sections of CIGR. Four other groups also held their activities during the conference. The American Society of Agricultural and Biological Engineers (ASABE) organized its 9th international drainage symposium and the American Ecological Engineering Society (AEES) held its 10th annual meeting. The International Network for Information Technology in Agriculture (INFITA), and the 8th world congress on computers in agriculture also joined CIGR 2010.

  16. My Career and the "Rhetoric of" Technical Writing and Communication

    Science.gov (United States)

    Schuster, Mary Lay

    2015-01-01

    This article traces the history of Mary Schuster's career in technical writing and communication from 1968 when she took a position in the Publications Department at the Institute of Electrical and Electronics Engineers (IEEE) to her work at "Technical Communication Quarterly" ("TCQ") in 2003 and forward. She discusses the…

  17. Washington Schools Learn from Value Engineering.

    Science.gov (United States)

    Doleae, Michael L.; Childs, Harvey C.

    1983-01-01

    Results of two value engineering studies have shown that a review early in the design process can help save costs in school construction, maintenance, operation, and replacement. The value engineering concepts and technical manual are being presented throughout the state of Washington. (MLF)

  18. Software engineering a practitioner's approach

    CERN Document Server

    Pressman, Roger S

    1997-01-01

    This indispensable guide to software engineering exploration enables practitioners to navigate the ins and outs of this rapidly changing field. Pressman's fully revised and updated Fourth Edition provides in-depth coverage of every important management and technical topic in software engineering. Moreover, readers will find the inclusion of the hottest developments in the field such as: formal methods and cleanroom software engineering, business process reengineering, and software reengineering.

  19. Dynamic Coordinated Shifting Control of Automated Mechanical Transmissions without a Clutch in a Plug-In Hybrid Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Xinlei Liu

    2012-08-01

    Full Text Available On the basis of the shifting process of automated mechanical transmissions (AMTs for traditional hybrid electric vehicles (HEVs, and by combining the features of electric machines with fast response speed, the dynamic model of the hybrid electric AMT vehicle powertrain is built up, the dynamic characteristics of each phase of shifting process are analyzed, and a control strategy in which torque and speed of the engine and electric machine are coordinatively controlled to achieve AMT shifting control for a plug-in hybrid electric vehicle (PHEV without clutch is proposed. In the shifting process, the engine and electric machine are well controlled, and the shift jerk and power interruption and restoration time are reduced. Simulation and real car test results show that the proposed control strategy can more efficiently improve the shift quality for PHEVs equipped with AMTs.

  20. Hanford Site technical baseline database. Revision 1

    International Nuclear Information System (INIS)

    Porter, P.E.

    1995-01-01

    This report lists the Hanford specific files (Table 1) that make up the Hanford Site Technical Baseline Database. Table 2 includes the delta files that delineate the differences between this revision and revision 0 of the Hanford Site Technical Baseline Database. This information is being managed and maintained on the Hanford RDD-100 System, which uses the capabilities of RDD-100, a systems engineering software system of Ascent Logic Corporation (ALC). This revision of the Hanford Site Technical Baseline Database uses RDD-100 version 3.0.2.2 (see Table 3). Directories reflect those controlled by the Hanford RDD-100 System Administrator. Table 4 provides information regarding the platform. A cassette tape containing the Hanford Site Technical Baseline Database is available

  1. Teaching audience analysis to the technical student

    Science.gov (United States)

    Debs, M. B.; Brillhart, L. V.

    1981-01-01

    Teaching audience analysis, as practiced in a technical writing course for engineering students, is discussed. Audience analysis is described as the task of defining the audience for a particular piece of writing and determining those characteristics of the audience which constrain the writer and effect reception of the message. A mature technical writing style that shows the tension produced when a text is written to be read and understood is considered in terms of audience analysis. Techniques include: (1) conveying to students the concept that a reader with certain expectations exist, (2) team teaching to preserve the context of a given technical discipline, and (3) assigning a technical report that addresses a variety of readers, thus establishing the complexity of audience oriented writing.

  2. FY 2003 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Fowler, B. A. (Compiler)

    2004-01-01

    This Technical Memorandum (TM) presents formal NASA technical reports, papers published in technical journals, and presentations by Marshall Space Flight Center (MSFC) personnel in FY 2003. It also includes papers of MSFC contractors. After being announced in STAR, all NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Spring.eld, VA 22161. The information in this TM may be of value to the scientific and engineering community in determining what information has been published and what is available.

  3. Training Engineering Disciplines and Skills through Robot Projects

    DEFF Research Database (Denmark)

    Friesel, Anna

    The popularity of robots in educational activities increased the last 10-15 years. Engineering education all over the world includes courses and projects involving design, use and programming of robots in a variety of programs at technical colleges and universities. At the same time there is a gr......The popularity of robots in educational activities increased the last 10-15 years. Engineering education all over the world includes courses and projects involving design, use and programming of robots in a variety of programs at technical colleges and universities. At the same time...... there is a growing interest to work with robots. Robotic skills are also highly requested in industrial companies. At the Technical University of Denmark, DTU Diplom, we have several projects involving building and programing robots in our bachelor programs in Electronics, Computer Science, IT and Mechanical...... Engineering. This presentation deals with our experience in robotic activities in different programs in order to enhance understanding of mathematics, physics and different technical disciplines in the named programs. We also observed the increased motivation for learning theory when we combine traditional...

  4. Some technical writing skills industry needs

    Science.gov (United States)

    Smith, F. R.

    1981-01-01

    It is suggested that engineers and other technical students be taught three classes of skills in technical writing. First, "Big Picture Things", which includes: the importance of clear writing, the wide scope of writing, the wide scope of writing tasks that will be faced in industry, and the principles of organization of technical materials such as; how to analyze, classify, partition, and interpret. Second, "Writing Procedures", which encompasses: how to get words on paper efficiently and team-write. Third, "Writing Details", in which two considerations are important: how to achieve precision in the use of language and the aspects of style. Three problems in style are cited: the problem of sentence transition, overuse of attributive adjectives, and verbosity in paragraph structure. The most important thing in technical writing is considered to be functionality, economy and clarity.

  5. Culture and Workplace Communications: A Comparison of the Technical Communications Practices of Japanese and U.S. Aerospace Engineers and Scientists

    Science.gov (United States)

    Pinelli, Thomas E. (Editor); Sato, Yuko (Editor); Barclay, Rebecca O. (Editor); Kennedy, John M. (Editor)

    1997-01-01

    The advent of global markets elevates the role and importance of culture as a mitigating factor in the diffusion of knowledge and technology and in product and process innovation. This is especially true in the large commercial aircraft (LCA) sector where the production and market aspects are becoming increasingly international. As firms expand beyond their national borders, using such methods as risk-sharing partnerships, joint ventures, outsourcing, and alliances, they have to contend with national and corporate cultures. Our focus is on Japan, a program participant in the production of the Boeing Company's 777. The aspects of Japanese culture and workplace communications will be examined: (1) the influence of Japanese culture on the diffusion of knowledge and technology in aerospace at the national and international levels; (2) those cultural determinants-the propensity to work together, a willingness to subsume individual interests to a greater good, and an emphasis on consensual decision making-that have a direct bearing on the ability of Japanese firms to form alliances and compete in international markets; (3) and those cultural determinants thought to influence the information-seeking behaviors and workplace communication practices of Japanese aerospace engineers and scientists. In this article, we report selective results from a survey of Japanese and U.S. aerospace engineers and scientists that focused on workplace communications. Data are presented for the following topics: importance of and time spent communicating information, collaborative writing, need for an undergraduate course in technical communication, use of libraries, use and importance of electronic (computer) networks, and the use and importance of foreign and domestically produced technical reports.

  6. Core Capabilities and Technical Enhancement -- FY-98 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Miller, David Lynn

    1999-04-01

    The Core Capability and Technical Enhancement (CC&TE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CC&TE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CC&TE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

  7. Core capabilities and technical enhancement, FY-98 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D.L.

    1999-04-01

    The Core Capability and Technical Enhancement (CCTE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CCTE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CCTE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

  8. Comparative analysis between a PEM fuel cell and an internal combustion engine driving an electricity generator: Technical, economical and ecological aspects

    International Nuclear Information System (INIS)

    Braga, Lúcia Bollini; Silveira, Jose Luz; Evaristo da Silva, Marcio; Machin, Einara Blanco; Pedroso, Daniel Travieso; Tuna, Celso Eduardo

    2014-01-01

    In the recent years the fuel cells have received much attention. Among various technologies, the Proton Exchange Membrane Fuel Cell (PEMFC) is currently the most appropriate and is used in several vehicles prototype. A comparative technical, economical and ecological analysis between an Internal Combustion Engine fueled with Diesel driving an electricity Generator (ICE-G) and a PEMFC fed by hydrogen produced by ethanol steam reforming was performed. The technical analysis showed the advantages of the PEMFC in comparison to the ICE-G based in energetic and exergetic aspects. The economic analysis shows that fuel cells are not economic competitive when compared to internal combustion engine driving an electricity generator with the same generation capacity; it will only be economically feasible in a long term; due to the large investments required. The environmental analysis was based on concepts of CO 2 equivalent, pollution indicator and ecological efficiency. Different to the ICE-G system, the Fuel Cell does not emit pollutants directly and the emission related to this technology is linked mainly with hydrogen production. The ecological efficiency of PEMFC was 96% considering the carbon dioxide cycle, for ICE-G system this parameter reach 51%. -- Highlights: • The exergetic efficiency of ICE-G was 22% and for the fuel cell was 40%. • The PEM fuel cell at long-term become economically competitive compared to ICE-G. • The ecological efficiency of PEM fuel cell was 96% and Diesel ICE-G was 51%

  9. Technical support of standards for high-level radioactive waste management. Volume B. Engineering controls. Task b report Mar-Aug 77

    International Nuclear Information System (INIS)

    1979-01-01

    This report is the result of work performed under the second part (Task B) of a four-part contract to gather technical information to evaluate enviornmental acceptablity of various options for disposing high-level wastes. The other tasks are: A-Source Term Characterization; C-Assessment of Migration Pathways; D-Assessment of Accidental Pathways. The scope of work for Task B was divided into 2 major steps: analysis of technology for engineering control of high-level wastes, and projections of costs for various alternative disposal technologies. Primary emphasis has been placed in non-reprocessed spent fuel. Brief consideration has been given to lower-level transuranic contaminated wastes which arise primarily from plutonium fuel fabrication and reprocessing plants. The objective of this limited review is to provide some insight into the state of the art for applying engineering controls to such wastes, including, where necessary, direct burial with high-level wastes in a geologic disposal facility

  10. Solid Waste Program technical baseline description

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, A.B.

    1994-07-01

    The system engineering approach has been taken to describe the technical baseline under which the Solid Waste Program is currently operating. The document contains a mission analysis, function analysis, system definition, documentation requirements, facility and project bases, and uncertainties facing the program.

  11. Environmental Engineering Curricula assessment in the global world

    Science.gov (United States)

    Caporali, Enrica; Catelani, Marcantonio; Manfrida, Giampaolo; Valdiserri, Juna

    2014-05-01

    Environmental engineers are technicians with specific expertise on the sustainability of human presence in the environment. Among other global dilemmas, to the environmental engineers it is often demanded to be able in developing systematic, innovative solutions in order to simultaneously meet water and energy needs, to build resilience to natural and technological disasters, to more accurately gauge and manage countries' greenhouse gas emissions. The general objectives of the Environmental Engineers are to establish actions of environmental sustainability as well as to verify progress toward global goals or international commitments. The globalization of challenges and problems to be faced, leads, in general, to the globalization of the engineering profession. In particular, since the environmental issues are without boundaries, and many and different are the involved professions and the competences, the environmental engineer must have a multidisciplinary and interdisciplinary approach to adequately answer to the demand of technical innovative knowledge at global scale. The environmental engineers, more and more, are involved in international projects were the effective collaboration requires not only the capacity to communicate in a common technical language, but also the assurance of an adequate and common level of technical competences, knowledge and understanding. The Europe-based EUR ACE system, currently operated by ENAEE - European Network for Accreditation of Engineering Education, can represent the proper framework and accreditation system in order to provide a set of measures to assess the quality of engineering degree programmes in Europe and abroad. In the global frame of the knowledge triangle: education-innovation-research, the accreditation and quality assurance of engineering curricula in Europe is discussed with reference to the Environmental engineering curricula, of the 1st and 2nd cycle, based on the European Credit Transfer System and in

  12. Developing English Communication Expertise for Engineers in the Global Age

    Science.gov (United States)

    Ono, Yoshimasa A.; Morimura, Kumiko

    This paper discusses contents and results of a new graduate course “English for Engineers and Scientists” given at School of Engineering, The University of Tokyo. This course is a new attempt to develop English communication expertise for engineering graduate students: how to write technical papers and how to make technical presentations in English. For these purposes, differences in the writing styles and in the sentence structures of English and Japanese are stressed: conclusions come first in English versus conclusions come last in Japanese; the three-step style of introduction, body, and conclusion in English versus the four-step style of ki-sho-ten-ketsu in Japanese. In addition, proper styles of technical papers (rhetoric) and related grammatical points are discussed. Technical presentation course consists of four-week lecture and seven-week practice session. In the lecture, essential points of technical presentations in English are discussed in detail, and in the practice session students‧ presentation skills are improved through guidance and instructions given by native-speaker moderators. The class evaluation results show that most students have obtained necessary skills of technical presentation, indicating that the combined course of lecture and practice session is essential for training students to make better technical presentations in English.

  13. Technical Leadership Development Program

    Science.gov (United States)

    2010-12-13

    the traditional tenets of leadership and management , systems thinking, understanding SOS issues, and thinking and acting holistically. Our research...international element 2.0 Enterprise Leadership and Management UNCLASSIFIED Contract Number: H98230-08-D-0171 DO 002. TO002, RT 004 Report No...mechanisms for leadership of the overall technical effort, for systems engineering, for requirements, management , and for systems integration. o Develop

  14. Computer-aided System of Semantic Text Analysis of a Technical Specification

    OpenAIRE

    Zaboleeva-Zotova, Alla; Orlova, Yulia

    2008-01-01

    The given work is devoted to development of the computer-aided system of semantic text analysis of a technical specification. The purpose of this work is to increase efficiency of software engineering based on automation of semantic text analysis of a technical specification. In work it is offered and investigated the model of the analysis of the text of the technical project is submitted, the attribute grammar of a technical specification, intended for formalization of limited Ru...

  15. Internal combustion engines history - a review

    International Nuclear Information System (INIS)

    Gaviria Rios, Jorge Enrique; Mora Guzman, Jorge Hernan; Agudelo, John Ramiro

    2002-01-01

    In this article, a chronological analysis of the technologies and events that any way influenced in the evolution of the internal combustion engine is done everything it through the observation of the works carried out for scientific empiric and engineers whose technical and conceptual value meant the motivation of other people for the search of a better development in this engineering field

  16. Clerget 100 hp heavy-oil engine

    Science.gov (United States)

    Leglise, Pierre

    1931-01-01

    A complete technical description of the Clerget heavy-oil engine is presented along with the general characteristics. The general characteristics are: 9 cylinders, bore 120 mm, stroke 130 mm, four-stroke cycle engine, rated power limited to 100 hp at 1800 rpm; weight 228 kg; propeller with direct drive and air cooling. Moving parts, engine block, and lubrication are all presented.

  17. An assessment of radiographers’ technical and protective performance in hospitals affiliated to Birjand University of Medical Sciences in 2012

    Directory of Open Access Journals (Sweden)

    Mahmood Reza Tavakkoli

    2014-08-01

    Materials and Methods: In this descriptive-analytical study, all the 26 radiolographers working in the radiology wards of Vali-asr and Imam Reza hospitals of Birjand participated. In order to collect data about their performance, a checklist whose reliability and validity had been approved was provided. For the radiography staff 17 technical and 12 protective items during three work shifts were checked and recorded. In order to measure their awareness of technical and protective principles, a 12-item questionnaire was completed by each of them. The obtained data was statistically analyzed by means of SPSS software using X2. Results: Mean Performance score in the technical area in the three work shifts was 15±1.60, and that of the protective area was 10.9±1.1 both of which were at an average level. Around 46.5% of the subjects gave correct answers to protective and 37.2% of them to the technical questions. The comparison of technical and protective performance scores showed no significant difference in terms of work shifts, education, gender, and type of employment (P>0.05. Conclusion: The radiographers’ awareness of technical and protective principles was at a very low level. Therefore, both quality academic training and in-service education seem necessary.

  18. ITER technical basis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties.

  19. ITER technical basis

    International Nuclear Information System (INIS)

    2002-01-01

    Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties

  20. Sources of technical assistance

    International Nuclear Information System (INIS)

    Laue, H.J.

    1977-01-01

    This paper shows examples of technical assistance programmes within bilateral cooperation agreements between the Federal Republic of Germany and a number of developing countries of very different characteristics and summarizes the possibilities of technical assistance granted by international organizations, such as IAEA, UNDP, etc. A basic requirement for a successful transfer of technology is a high knowledge level of the indigenous scientists and engineers. Therefore, programmes for training and education and for information exchange are presented. Based on these, the means and methods of planning, performance and quality assurance are explained by practical examples and are related to the progress achieved in the use of nuclear energy and in establishing a national industry in the developing countries. (orig.) [de

  1. NASA Space Environments Technical Discipline Team Space Weather Activities

    Science.gov (United States)

    Minow, J. I.; Nicholas, A. C.; Parker, L. N.; Xapsos, M.; Walker, P. W.; Stauffer, C.

    2017-12-01

    The Space Environment Technical Discipline Team (TDT) is a technical organization led by NASA's Technical Fellow for Space Environments that supports NASA's Office of the Chief Engineer through the NASA Engineering and Safety Center. The Space Environments TDT conducts independent technical assessments related to the space environment and space weather impacts on spacecraft for NASA programs and provides technical expertise to NASA management and programs where required. This presentation will highlight the status of applied space weather activities within the Space Environment TDT that support development of operational space weather applications and a better understanding of the impacts of space weather on space systems. We will first discuss a tool that has been developed for evaluating space weather launch constraints that are used to protect launch vehicles from hazardous space weather. We then describe an effort to better characterize three-dimensional radiation transport for CubeSat spacecraft and processing of micro-dosimeter data from the International Space Station which the team plans to make available to the space science community. Finally, we will conclude with a quick description of an effort to maintain access to the real-time solar wind data provided by the Advanced Composition Explorer satellite at the Sun-Earth L1 point.

  2. How to develop and write a case for technical writing

    Science.gov (United States)

    Couture, B.; Goldstein, J.

    1981-01-01

    Case of different sizes and shapes for teaching technical writing to engineers at Wayne State University have been developed. The case approach was adopted for some assignments because sophomores and juniors lacked technical expertise and professional knowledge of the engineering world. Cases were found to be good exercises, providing realistic practice in specific writing tasks or isolating particular skills in the composing process. A special kind of case which narrates the experiences of one technical person engaged in the problem-solving process in a professional rhetorical situation was developed. This type of long, realistic fiction is called a an "holistic" case. Rather than asking students to role-play a character, an holistic case realistically encompasses the whole of the technical writing process. It allows students to experience the total communication act in which the technical task and data are fully integrated into the rhetorical situation and gives an opportunity to perform in a realistic context, using skills and knowledge required in communication on the job. It is believed that the holistic case most fully exploits the advantages of the case method for students of professional communication.

  3. Decision Analysis: Engineering Science or Clinical Art

    Science.gov (United States)

    1979-11-01

    TECHNICAL REPORT TR 79-2-97 DECISION ANALYSIS: ENGINEERING SCIENCE OR CLINICAL ART ? by Dennis M. Buede Prepared for Defense Advanced Research...APPLICATIONS OF THE ENGINEER- ING SCIENCE AND CLINICAL ART EXTREMES 9 3.1 Applications of the Engineering Science Approach 9 3.1.1 Mexican electrical...DISCUSSION 29 4.1 Engineering Science versus Clinical Art : A Characterization of When Each is Most Attractive 30 4.2 The Implications of the Engineering

  4. Security Engineering FY17 Systems Aware Cybersecurity

    Science.gov (United States)

    2017-12-07

    Security Engineering – FY17 Systems Aware Cybersecurity Technical Report SERC-2017-TR-114 December 7 2017 Principal Investigator: Dr...December 7, 2017 Copyright © 2017 Stevens Institute of Technology, Systems Engineering Research Center The Systems Engineering Research Center (SERC...supported, in whole or in part, by the U.S. Department of Defense through the Office of the Assistant Secretary of Defense for Research and Engineering (ASD

  5. PROFESSIONALLY ORIENTED COURSE OF ENGINEERING-GRAPHICAL TRAINING

    Directory of Open Access Journals (Sweden)

    Olga V. Zhuykova

    2015-01-01

    Full Text Available The aim of the article is to present the results of managing the competence oriented self-directed student learning while studying graphical subjects at Kalashnikov Izhevsk State Technical University.Methods. The technology of self-directed engineering-graphical training of future bachelors based on the analysis of educational literature and teaching experience, providing individualization and professional education is suggested. The method of team expert appraisal was used at all stages of self-directed learning management. This method is one of main in qualimetry (the science concerned with assessing and evaluating the quality of any objects and processes; it permits to reveal the components of engineering-graphical competence, to establish the criteria and markers of determining the level of its development, to perform expert evaluation of student tasks and estimation procedures.Results. It has been established that the revitalization of student selfdirected learning owing to professional education and individualization permits to increase the level of student engineering-graphical competence development. Scientific novelty. The criteria evaluation procedures for determining the level of student engineering-graphical competence development in the process of their professional oriented self-directed learning while studying graphical subjects at a technical university are developed.Practical significance. The professional-focused educational trajectories of independent engineering-graphic preparation of students are designed and substantially filled in content. Such training is being realised at the present time at Kalashnikov Izhevsk State Technical University, major «Instrument Engineering». 

  6. Engineering and Narrative: Literary Prerequisites as Indirect Communication for Technical Writing

    Science.gov (United States)

    Jeyaraj, Joseph

    2014-01-01

    While Engineering values direct communication, indirect communication produces a kind of literacy salient for engineers that direct communication may not offer in the way indirect communication does. This article emphasizes the inadequacies of overly emphasizing direct communication for Engineering majors and explains how teaching indirect…

  7. Symposium on engineering with nuclear explosives. Proceedings. Volume 2

    International Nuclear Information System (INIS)

    1970-05-01

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. This proceedings is the record of the symposium

  8. Symposium on engineering with nuclear explosives. Proceedings. Vol. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1970-05-01

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. These proceedings are the record of the symposium.

  9. Symposium on engineering with nuclear explosives. Proceedings. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1970-05-15

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. This proceedings is the record of the symposium.

  10. Symposium on engineering with nuclear explosives. Proceedings. Vol. 1

    International Nuclear Information System (INIS)

    1970-05-01

    This symposium on 'Engineering with Nuclear Explosives' reports to the Plowshare community, both national and international, the progress achieved since April 1964, the date of the Third Plowshare Symposium. In structuring the technical presentations, contributions of broadest interest were placed at the beginning, thus forming a common base of current information and applied science understanding developed in support of Plowshare technology. Sessions of speciality or pertaining to specific areas of application and engineering follow logically in the program. The Plenary Session reviewed the current status of the Plowshare Program from the technical, government, and industrial points of view. The 112 papers presented at 15 technical sessions covered all technical aspects of the Plowshare Program. The conference summary reviewed principal themes, areas of significant advance, and subjects requiring further attention that emerged during the technical conference. These proceedings are the record of the symposium

  11. Technical progress safeguards future. Technischer Fortschritt sichert die Zukunft

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    'Technical progress safeguards future', the guiding theme of the 1985 conference of German engineers, calls for discussion. In five lectures representatives of the subdivisions of 'VDI' issued their statements from the viewpoints of their special fields. These lectures were completed by reports on the part of the remaining VDI subdivisions, which are published together with the lectures in this volume. The complex guiding theme is meant to stimulate discussion, which should be conducted also with representatives of other sciences and the public. The volume contains a.o. contributions regarding future prospects, given certain modifications in construction engineering and user behaviour in the sector heating and air-conditioning, regarding the development of new construction techniques to protect the environment, and regarding clean air as an international concern of engineers. For these three contributions separate entries were made. Other presentations relate to: automobile production technology; energy supply as an engineering task; information, invention, innovation as stages of technical progress; progress in materials technology; noise of motor vehicles - current state and future prospects. (orig./HSCH).

  12. Hot air balloon engine

    Energy Technology Data Exchange (ETDEWEB)

    Edmonds, Ian [Solartran Pty Ltd, 12 Lentara Street, Kenmore, Brisbane 4069 (Australia)

    2009-04-15

    This paper describes a solar powered reciprocating engine based on the use of a tethered hot air balloon fuelled by hot air from a glazed collector. The basic theory of the balloon engine is derived and used to predict the performance of engines in the 10 kW to 1 MW range. The engine can operate over several thousand metres altitude with thermal efficiencies higher than 5%. The engine thermal efficiency compares favorably with the efficiency of other engines, such as solar updraft towers, that also utilize the atmospheric temperature gradient but are limited by technical constraints to operate over a much lower altitude range. The increased efficiency allows the use of smaller area glazed collectors. Preliminary cost estimates suggest a lower $/W installation cost than equivalent power output tower engines. (author)

  13. FY 1991 scientific and technical reports, articles, papers, and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1991-01-01

    Formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 1991 are presented. Papers of MSFC contractors are also included. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  14. Software engineering laboratory series: Annotated bibliography of software engineering laboratory literature

    Science.gov (United States)

    Morusiewicz, Linda; Valett, Jon

    1992-01-01

    This document is an annotated bibliography of technical papers, documents, and memorandums produced by or related to the Software Engineering Laboratory. More than 100 publications are summarized. These publications cover many areas of software engineering and range from research reports to software documentation. This document has been updated and reorganized substantially since the original version (SEL-82-006, November 1982). All materials have been grouped into eight general subject areas for easy reference: (1) the Software Engineering Laboratory; (2) the Software Engineering Laboratory: Software Development Documents; (3) Software Tools; (4) Software Models; (5) Software Measurement; (6) Technology Evaluations; (7) Ada Technology; and (8) Data Collection. This document contains an index of these publications classified by individual author.

  15. Extension of shift-invariant systems in L2(ℝ) to frames

    DEFF Research Database (Denmark)

    Bownik, Marcin; Christensen, Ole; Huang, Xinli

    2012-01-01

    In this article, we show that any shift-invariant Bessel sequence with an at most countable number of generators can be extended to a tight frame for its closed linear span by adding another shift-invariant system with at most the same number of generators. We show that in general this result...... is optimal, by providing examples where it is impossible to obtain a tight frame by adding a smaller number of generators. An alternative construction (which avoids the technical complication of extracting the square root of a positive operator) yields an extension of the given Bessel sequence to a pair...

  16. Engineering support strategies in the competitive environment

    International Nuclear Information System (INIS)

    Casella, L.R.; Hall, T.E.; Stark, D.R.

    1996-01-01

    This paper focuses on the innovative use of support personnel during plant outages and other maintenance/upkeep periods. At the South Texas Project the authors have formed an engineering support group specifically tailored to provide real time solutions to maintenance and operation problems. The core group consists of a cross section from the engineering disciplines and systems engineers. The group is housed in the Maintenance and Operations Facility adjacent to the power block. Close proximity and maintenance and operations personnel improves communications and response to emergent technical issues. During outages the group is augmented with additional personnel from the Design and Systems Engineering Departments. This allows for around the clock support that directly complements plant operations activities and maintenance tasks. The Thirty Minute Rule highlights urgent issues requiring engineering management attention. Dedicated twenty-four (24) hour engineering management oversight completes the engineering outage support package. Revised procedures, networks, and software enhancements, streamline the interface between engineering and work control processes. Good communications across the engineering disciplines and departments provide for enhanced teamwork and timely resolution of emergent technical issues for customers. The techniques to be described in the paper contributed directly to the South Texas Project recently establishing a new world record for a Westinghouse 3 and 4 loop pressurized water reactor refueling outage

  17. IPEN Scientific and technical publications 1956-1981

    International Nuclear Information System (INIS)

    1983-01-01

    The Instituto de Pesquisas Energeticas e Nucleares - IPEN (Energy Research Institute) from Sao Paulo, Brazil, was founded in 1956. Since its foundation, the main objectives of IPEN has been to undertake research and development into the peaceful uses of nuclear energy and to train scientific personnel to post-graduate level. The IPEN Scientific and Technical Publication - IPEN/SP, is a system developed at IPEN. Its purpose has been to generate a data base identifying the technical and scientific literature produced by IPEN staff members, published either in the Institute's series or in others brazilian and foreign publications. Documents cited in this jubilee edition include those in which IPEN staff members were authors or co-authors; document published by foreign research visitors while working at IPEN facilities; theses prepared by IPEN staff and reports in which IPEN is a corporate author. The IPEN technical publications reflect the main fields of research persuaded by the Institute, namely nuclear physics radiochemistry, chemical engineering, nuclear metallurgy and engineering and finally medical and industrial applications of radioisotopes. This present volume, published under the new title of IPEN - Scientific and Technical Publications, is a cumulative edition, to celebrate the 25th. anniversary of IPEN. In this jubilee edition, 1345 document published by IPEN staff are cited, following the main subject heading of INIS Subject Categories. (author)

  18. Current status of nuclear engineering education

    International Nuclear Information System (INIS)

    Palladino, N.J.

    1975-01-01

    The 65 colleges and universities offering undergraduate degrees in nuclear engineering and the 15 schools offering strong nuclear engineering options are, in general, doing a good job to meet the current spectrum of job opportunities. But, nuclear engineering programs are not producing enough graduates to meet growing demands. They currently receive little aid and support from their customers --industry and government--in the form of scholarships, grants, faculty research support, student thesis and project support, or student summer jobs. There is not enough interaction between industry and universities. Most nuclear engineering programs are geared too closely to the technology of the present family of reactors and too little to the future breeder reactors and controlled thermonuclear reactors. In addition, nuclear engineering programs attract too few women and members of minority ethnic groups. Further study of the reasons for this fact is needed so that effective corrective action can be taken. Faculty in nuclear engineering programs should assume greater initiative to provide attractive and objective nuclear energy electives for technical and nontechnical students in other disciplines to improve their technical understanding of the safety and environmental issues involved. More aggressive and persistent efforts must be made by nuclear engineering schools to obtain industry support and involvement in their programs

  19. Power plant engineering dictionary. Vol. 2. 4. rev. and enlarged ed.

    International Nuclear Information System (INIS)

    1987-01-01

    The dictionary is a compilation of 6000 German and English technical terms of power plant engineering as far as power plants, turbine-generators and assembly engineering are concerned. It is meant to form a basis for uniform terminology on technical documents. The dictionary is the result of a joint effort of KWU and UPC. (DG)

  20. Technical dictionary power plant engineering. Vol. 1. German - English. - Pt. 1: Dictionary. Pt. 2: Abbreviations. 4. rev. and enlarged ed. Technisches Woerterbuch Kraftwerkstechnik. Bd. 1. Deutsch - Englisch. - T. 1: Woerterbuch. T. 2: Abkuerzungen

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    This dictionary is a compilation of German and English technical terms of power plant engineering as far as power plants, turbine-generators and assembly engineering are concerned. It is the result of a joint effort by the Kraftwerk Union AG (KWU) and Utility Power Corp. (UPC). The entire content has been revised and approx. 6000 new terms have been added. The dictionary is meant to form a basis for uniform terminology on technical documents as well as correspondence between KWU, UPC and licensees. This computer aided dictionary is printed in capital/low case letters. Only nouns, terms with an article and proper names are capitalized in German. Some terms are written differently in American and British English and are marked with (US) or (GB).

  1. Fault localization technics in energy and communication cables. Fehlerortungstechnik in Energie- und Nachrichtenkabeln

    Energy Technology Data Exchange (ETDEWEB)

    Bartz, W G; Wippler, E

    1981-01-01

    Though fault localization technics in energy and information cables represents a special field within electrical engineering or electrical measurement engineering its significance becomes visible when fault-localization technics is seen with the same eyes as energy supply or information exchange. To maintain supply and exchange disturbance free, e.g. by means of continuous or periodical monitoring or to restore them quickly in case of disturbance is the task of fault localization technics. This new volume shall give a survey on the network structures in energy and communication networks, on the types and frequency of past interruptions and also on procedures to evaluate interruptions statistically. Methods, procedures and measurement techniques of fault-localization technics are presented for usual communication and energy cables as well as for optical communication cables.

  2. Engineering for Sustainable Development - An obligatory Skill of the Future Engineer

    DEFF Research Database (Denmark)

    Hauschild, Michael Zwicky; Alting, Leo; Molin, Christine

    2003-01-01

    , Bruxelles (Belgium). Department of Manufacturing Engineering and Management hosted a mini-tutorial on Courses and Curricula in Sustainable Development and Environmental Management at the Technical University of Denmark. The procedings comprise papers from universities and institutions in many countries...

  3. TECHNICAL COORDINATION

    CERN Document Server

    A. Ball and W. Zeuner

    2013-01-01

    For the reporting period, the CMS common systems and infrastructure worked well, without failures that caused significant data losses. One more disconnection of the magnet cold box occurred in the shadow of interruptions in data taking, caused by a series of technical faults. The recognition during 2012 that re-connection can only safely be done at around 2 T implies a minimum magnet recovery time of 12 hours and raises serious concerns about the number of ramping cycles of the magnet these incidents cause. This has triggered studies of how to make the cryo-system of the magnet more robust against failures. The proton-proton run ended just before the end-of-year CERN closure, during which CASTOR was installed on the negative end of CMS and both ZDC calorimeters were installed in TAN absorbers the LHC tunnel, in preparation for the heavy-ion run. The installation of CASTOR was an excellent “engineering test” of procedures for working in an activated environment. Despite some technical pr...

  4. Prevent recurrence of nuclear disaster (3). Agenda on nuclear safety from earthquake engineering

    International Nuclear Information System (INIS)

    Kameda, Hiroyuki; Takada, Tsuyoshi; Ebisawa, Katsumi; Nakamura, Susumu

    2012-01-01

    Based on results of activities of committee on seismic safety of nuclear power plants (NPPs) of Japan Association for Earthquake Engineering, which started activities after Chuetsu-oki earthquake and then experienced Great East Japan Earthquake, (under close collaboration with the committee of Atomic Energy Society of Japan started activities simultaneously), and taking account of further development of concept, agenda on nuclear safety were proposed from earthquake engineering. In order to prevent recurrence of nuclear disaster, individual technical issues of earthquake engineering and comprehensive issues of integration technology, multidisciplinary collaboration and establishment of technology governance based on them were of prime importance. This article described important problems to be solved; (1) technical issues and mission of seismic safety of NPPs, (2) decision making based on risk assessment - basis of technical governance, (3) framework of risk, design and regulation - framework of required technology governance, (4) technical issues of earthquake engineering for nuclear safety, (5) role of earthquake engineering in nuclear power risk communication and (6) importance of multidisciplinary collaboration. Responsibility of engineering would be attributed to establishment of technology governance, cultivation of individual technology and integration technology, and social communications. (T. Tanaka)

  5. Revising an Engineering Design Rubric: A Case Study Illustrating Principles and Practices to Ensure Technical Quality of Rubrics

    Directory of Open Access Journals (Sweden)

    Gail Lynn Goldberg

    2014-08-01

    Full Text Available This article provides a detailed account of a rubric revision process to address seven common problems to which rubrics are prone: lack of consistency and parallelism; the presence of - orphan- and - widow- words and phrases; redundancy in descriptors; inconsistency in the focus of qualifiers; limited routes to partial credit; unevenness in incremental levels of performance; and inconsistencies across suites or sets of related rubrics. The author uses examples from both the draft stage precursor and the first revised (pilot version of the Engineering Design Process Portfolio Scoring Rubric (EDPPSR, to illustrate the application of broadly relevant guidelines that can inform the creation of a new-'or revision of an existing-'rubric to achieve technical quality while preserving content integrity

  6. Preferences on technical report format - Results of a survey

    Science.gov (United States)

    Pinelli, T. E.; Cordle, V. M.; Glassman, M.; Vondran, R. F.

    1984-01-01

    A survey of 513 engineers and scientists employed at the National Aeronautics and Space Administration Langley Research Center and 600 engineers and scientists from three professional/technical societies solicited the opinions of report users concerning the format of NASA technical reports. The results indicate that a summary as well as an abstract should be included, that the definitions of symbols and glossary of terms should be located in the front of the report, and that the illustrative material should be integrated with the text rather than grouped at the end of the report. Citation of references by number, one-column, ragged-right-margin layout, and third-person writing style are also preferred by a majority of the respondents.

  7. NASA System Engineering Design Process

    Science.gov (United States)

    Roman, Jose

    2011-01-01

    This slide presentation reviews NASA's use of systems engineering for the complete life cycle of a project. Systems engineering is a methodical, disciplined approach for the design, realization, technical management, operations, and retirement of a system. Each phase of a NASA project is terminated with a Key decision point (KDP), which is supported by major reviews.

  8. ABET [Accreditation Board for Engineering and Technology] accreditation for engineering technology

    International Nuclear Information System (INIS)

    Foulke, L.R.

    1989-01-01

    Engineering technology is that part of the technological field that requires the application of scientific and engineering knowledge and methods combined with technical skills in support of engineering activities. It lies in the occupational spectrum between the craftsman and the engineer at the end of the spectrum closest to the engineer. The term engineering technician is applied to the graduates of associate degree programs. Graduates of baccalaureate programs are called engineering technologists. The content of a 4-yr engineering technology program treats the same subject areas as does an engineering program but with more emphasis on application, use of established design concepts, and the laboratory experience rather than on science, conceptual design, and new development. The mathematics content of accreditable baccalaureate programs must contain at least 12 semester-hour credits of mathematics including the study of calculus. Engineering managers should take a hard look at what is really needed in the education of that majority of a personnel who do not work as design and development engineers. Graduates of engineering technology programs may be better qualified than those of some engineering programs for the majority of jobs in our industry today

  9. FY 1998 Scientific and Technical Reports, Articles, Papers, and Presentations

    Science.gov (United States)

    Waits, J. E. Turner (Compiler)

    1999-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC (Marshall Space Flight Center) personnel in FY98. It also includes papers of MSFC contractors. After being announced in STAR, all of the NASA series reports may be obtained from the National Technical Information Service. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  10. IPEN scientific and technical publications 1984-1986

    International Nuclear Information System (INIS)

    1988-01-01

    The Instituto de Pesquisas Energeticas e Nucleares - IPEN (Energy Research Institute) from Sao Paulo, Brazil, was founded in 1956. Since its foundation, the main objectives of IPEN has been to undertake research and development into the peaceful uses of nuclear energy and to train scientific personnel to post-graduate level. The IPEN Scientific and Technical Publication - IPEN/STP, is a system developed at IPEN. Its purpose has been to generate a data base identifying the technical and scientific literature produced by IPEN staff members, published either in the Institute's series or in others brazilian and foreign publications. Documents cited in this 1984-1986 supplement include those in which IPEN staff members were authors or co-authors; document published by foreign research visitors while working at IPEN facilities; theses prepared by IPEN staff and reports in which IPEN is a corporate author. The IPEN technical publications reflect the main fields of research persuaded by the Institute, namely nuclear physics radiochemistry, chemical engineering, nuclear metallurgy and engineering and finally medical and industrial applications of radioisotopes. In this 1984-1986 supplement 458 document published by IPEN staff are cited, following the main subject heading of INIS Subject Categories. (author)

  11. IPEN Scientific and technical publications 1982-1983

    International Nuclear Information System (INIS)

    1984-01-01

    The Instituto de Pesquisas Energeticas e Nucleares - IPEN (Energy Research Institute) from Sao Paulo, Brazil, was founded in 1956. Since its foundation, the main objectives of IPEN has been to undertake research and development into the peaceful uses of nuclear energy and to train scientific personnel to post-graduate level. The IPEN Scientific and Technical Publication - IPEN/STP, is a system developed at IPEN. Its purpose has been to generate a data base identifying the technical and scientific literature produced by IPEN staff members, published either in the Institute's series or in others brazilian and foreign publications. Documents cited in this 1982-1983 supplement include those in which IPEN staff members were authors or co-authors; document published by foreign research visitors while working at IPEN facilities; theses prepared by IPEN staff and reports in which IPEN is a corporate author. The IPEN technical publications reflect the main fields of research persuaded by the Institute, namely nuclear physics radiochemistry, chemical engineering, nuclear metallurgy and engineering and finally medical and industrial applications of radioisotopes. In this 1982-1983 supplement 131 document published by IPEN staff are cited, following the main subject heading of INIS Subject Categories. (author)

  12. A Multidisciplinary Engineering Summer School in an Industrial Setting

    Science.gov (United States)

    Larsen, Peter Gorm; Fernandes, Joao M.; Habel, Jacek; Lehrskov, Hanne; Vos, Richard J. C.; Wallington, Oliver; Zidek, Jan

    2009-01-01

    Most university-level engineering studies produce technically skilled engineers. However, typically students face several difficulties when working in multidisciplinary teams when they initiate their industrial careers. In a globalised world, it becomes increasingly important that engineers are capable of collaborating across disciplinary…

  13. Engines and transmissions - producers and consumers; Motoren und Getriebe: Wer baut, wer verwendet?

    Energy Technology Data Exchange (ETDEWEB)

    Demel, H. [Magna Vehicle and Powertrain Group, Oberwaltersdorf (Austria)

    2007-07-01

    The following will address the development trends within global and regional engine and transmission markets. In times of steadily increasing vehicle production volumes and market globalization as well as a shift of core competences, OEMs and suppliers are facing new challenges. The following analysis highlights the market trends for engines and transmissions through technical and regional spectrums. New ways of production and development have been created and installed due to the globalization the automotive industry. Within the inter-connection of OEM companies there is a clear trend for outsourcing production. It is clear that design and development will stay within the core competences of the OEM but price pressures and fierce competition from low cost countries continue to lead to consolidation. The need for synergies is leading to the unification of production and development clusters. This partly explains why it has become very difficult to identify the origin of various vehicle parts or assemblies. Furthermore, finding an authentic regionally built car from a single OEM is becoming evermore rare as these factors take root in the global market. (orig.)

  14. The Effects of Integrating On-Going Training for Technical Documentation Teams

    Science.gov (United States)

    Catanio, Joseph T.; Catanio, Teri L.

    2010-01-01

    The tools and techniques utilized in the technical communications profession are constantly improving and changing. Information Technology (IT) organizations devote the necessary resources to equip and train engineering, marketing, and sales teams, but often fail to do so for technical documentation teams. Many IT organizations tend to view…

  15. Monitoring Bone Tissue Engineered (BTE) Constructs Based on the Shifting Metabolism of Differentiating Stem Cells.

    Science.gov (United States)

    Simmons, Aaron D; Sikavitsas, Vassilios I

    2018-01-01

    Ever-increasing demand for bone grafts necessitates the realization of clinical implementation of bone tissue engineered constructs. The predominant hurdle to implementation remains to be securing FDA approval, based on the lack of viable methods for the rigorous monitoring of said constructs. The study presented herein details a method for such monitoring based on the shifting metabolism of mesenchymal stem cells (MSCs) as they differentiate into osteoblasts. To that end, rat MSCs seeded on 85% porous spunbonded poly(L-lactic acid) scaffolds were cultured in flow perfusion bioreactors with baseline or osteoinductive media, and levels of key physio-metabolic markers (oxygen, glucose, osteoprotegerin, and osteocalcin) were monitored throughout culture. Comparison of these non-destructively obtained values and current standard destructive analyses demonstrated key trends useful for the concurrent real-time monitoring of construct cellularity and maturation. Principle among these is the elucidation of the ratio of the rates of oxygen uptake to glucose consumption as a powerful quality marker. This ratio, supported on a physiological basis, has been shown herein to be reliable in the determination of both construct maturation (defined as osteoblastic differentiation and accompanying mineralization) and construct cellularity. Supplementary monitoring of OPG and OCN are shown to provide further validation of such metrics.

  16. TECHNICAL BASIS FOR VENTILATION REQUIREMENTS IN TANK FARMS OPERATING SPECIFICATIONS DOCUMENTS

    Energy Technology Data Exchange (ETDEWEB)

    BERGLIN, E J

    2003-06-23

    This report provides the technical basis for high efficiency particulate air filter (HEPA) for Hanford tank farm ventilation systems (sometimes known as heating, ventilation and air conditioning [HVAC]) to support limits defined in Process Engineering Operating Specification Documents (OSDs). This technical basis included a review of older technical basis and provides clarifications, as necessary, to technical basis limit revisions or justification. This document provides an updated technical basis for tank farm ventilation systems related to Operation Specification Documents (OSDs) for double-shell tanks (DSTs), single-shell tanks (SSTs), double-contained receiver tanks (DCRTs), catch tanks, and various other miscellaneous facilities.

  17. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 11: The Voice of the User: How US Aerospace Engineers and Scientists View DoD Technical Reports

    Science.gov (United States)

    Pinelli, Thomas E.; Kennedy, John M.

    1991-01-01

    The project examines how the results of NASA/DOD research diffuse into the aerospace R&D process, and empirically analyzes the implications of the aerospace knowledge diffusion process. Specific issues considered are the roles played by government technical reports, the recognition of the value of scientific and technical information (STI), and the optimization of the STI aerospace transfer system. Information-seeking habits are assessed for the U.S. aerospace community, the general community, the academic sector, and the international community. U.S. aerospace engineers and scientists use 65 percent of working time to communicate STI, and prefer 'internal' STI over 'external' STI. The isolation from 'external' information is found to be detrimental to U.S. aerospace R&D in general.

  18. Improving Safety through Human Factors Engineering.

    Science.gov (United States)

    Siewert, Bettina; Hochman, Mary G

    2015-10-01

    Human factors engineering (HFE) focuses on the design and analysis of interactive systems that involve people, technical equipment, and work environment. HFE is informed by knowledge of human characteristics. It complements existing patient safety efforts by specifically taking into consideration that, as humans, frontline staff will inevitably make mistakes. Therefore, the systems with which they interact should be designed for the anticipation and mitigation of human errors. The goal of HFE is to optimize the interaction of humans with their work environment and technical equipment to maximize safety and efficiency. Special safeguards include usability testing, standardization of processes, and use of checklists and forcing functions. However, the effectiveness of the safety program and resiliency of the organization depend on timely reporting of all safety events independent of patient harm, including perceived potential risks, bad outcomes that occur even when proper protocols have been followed, and episodes of "improvisation" when formal guidelines are found not to exist. Therefore, an institution must adopt a robust culture of safety, where the focus is shifted from blaming individuals for errors to preventing future errors, and where barriers to speaking up-including barriers introduced by steep authority gradients-are minimized. This requires creation of formal guidelines to address safety concerns, establishment of unified teams with open communication and shared responsibility for patient safety, and education of managers and senior physicians to perceive the reporting of safety concerns as a benefit rather than a threat. © RSNA, 2015.

  19. Alternatives for Jet Engine Control. Volume 1: Modelling and Control Design with Jet Engine Data

    Science.gov (United States)

    Sain, M. K.

    1985-01-01

    This document compiles a comprehensive list of publications supported by, or related to, National Aeronautics and Space Administration Grant NSG-3048, entitled "Alternatives for Jet Engine Control". Dr. Kurt Seldner was the original Technical Officer for the grant, at Lewis Research Center. Dr. Bruce Lehtinen was the final Technical Officer. At the University of Notre Dame, Drs. Michael K. Sain and R. Jeffrey Leake were the original Project Directors, with Dr. Sain becoming the final Project Director. Publications cover work over a ten-year period. The Final Report is divided into two parts. Volume i, "Modelling and Control Design with Jet Engine Data", follows in this report. Volume 2, "Modelling and Control Design with Tensors", has been bound separately.

  20. Interactive Model-Centric Systems Engineering (IMCSE) Phase 5

    Science.gov (United States)

    2018-02-28

    Interactive Model-Centric Systems Engineering (IMCSE) Phase 5 Technical Report SERC-2018-TR-104 Feb 28, 2018 Principal Investigator...Date February 28, 2018 Copyright © 2018 Stevens Institute of Technology, Systems Engineering ...Research Center The Systems Engineering Research Center (SERC) is a federally funded University Affiliated Research Center managed by Stevens

  1. Concise dictionary of engineering a guide to the language of engineering

    CERN Document Server

    Hanifan, Ron

    2014-01-01

    This reference defines the principle and most commonly used terms found in engineering documents and drawings across multiple disciplines and explains them in plain, unambiguous English. Concise Dictionary of Engineering: A Guide to the Language of Engineering also distinguishes how some terms take on different meanings in different engineering contexts—critical knowledge when working on collaborative projects with diverse elements and colleagues. Based on an edition developed for researchers and technicians at Lockheed Martin, each entry in this volume is written in clear, everyday English without confusing jargon and “techno-speak.” The book is ideal for students, professional engineers, industrial personnel, managers, and anyone else who requires a solid understanding of the language of engineers. This dictionary also: ·         Clarifies technical terms often intermixed or misused ·         Spans a range of engineering disciplines, including mechanical, electrical, materials, and c...

  2. Ethics and the UN Sustainable Development Goals: The Case for Comprehensive Engineering : Commentary on "Using Student Engagement to Relocate Ethics to the Core of the Engineering Curriculum".

    Science.gov (United States)

    van den Hoven, Jeroen

    2016-12-27

    In the twenty-first century, the urgent problems the world is facing (the UN Sustainable Development Goals) are increasingly related to vast and intricate 'systems of systems', which comprise both socio-technical and eco-systems. In order for engineers to adequately and responsibly respond to these problems, they cannot focus on only one technical or any other aspect in isolation, but must adopt a wider and multidisciplinary perspective of these systems, including an ethical and social perspective. Engineering curricula should therefore focus on what we call 'comprehensive engineering'. Comprehensive engineering implies ethical coherence, consilience of scientific disciplines, and cooperation between parties.

  3. FY 1994 scientific and technical reports, articles, papers, and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1994-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by Marshall Space Flight Center personnel in FY94. It also includes papers of MSFC contractors and author indexes. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  4. Waste management project technical baseline description

    International Nuclear Information System (INIS)

    Sederburg, J.P.

    1997-01-01

    A systems engineering approach has been taken to describe the technical baseline under which the Waste Management Project is currently operating. The document contains a mission analysis, function analysis, requirement analysis, interface definitions, alternative analysis, system definition, documentation requirements, implementation definitions, and discussion of uncertainties facing the Project

  5. Engineering education research in European Journal of Engineering Education and Journal of Engineering Education: citation and reference discipline analysis

    Science.gov (United States)

    Wankat, Phillip C.; Williams, Bill; Neto, Pedro

    2014-01-01

    The authors, citations and content of European Journal of Engineering Education (EJEE) and Journal of Engineering Education (JEE) in 1973 (JEE, 1975 EJEE), 1983, 1993, 2003, and available 2013 issues were analysed. Both journals transitioned from house organs to become engineering education research (EER) journals, although JEE transitioned first. In this process the number of citations rose, particularly of education and psychology sources; the percentage of research articles increased markedly as did the number of reference disciplines. The number of papers per issue, the number of single author papers, and the citations of science and engineering sources decreased. EJEE has a very broad geographic spread of authors while JEE authors are mainly US based. A 'silo' mentality where general engineering education researchers do not communicate with EER researchers in different engineering disciplines is evident. There is some danger that EER may develop into a silo that does not communicate with technically oriented engineering professors.

  6. Driving and engine cycles

    CERN Document Server

    Giakoumis, Evangelos G

    2017-01-01

    This book presents in detail the most important driving and engine cycles used for the certification and testing of new vehicles and engines around the world. It covers chassis and engine-dynamometer cycles for passenger cars, light-duty vans, heavy-duty engines, non-road engines and motorcycles, offering detailed historical information and critical review. The book also provides detailed examples from SI and diesel engines and vehicles operating during various cycles, with a focus on how the engine behaves during transients and how this is reflected in emitted pollutants, CO2 and after-treatment systems operation. It describes the measurement methods for the testing of new vehicles and essential information on the procedure for creating a driving cycle. Lastly, it presents detailed technical specifications on the most important chassis-dynamometer cycles around the world, together with a direct comparison of those cycles.

  7. Technical database and management system (DBMS) for the UMTRA project processing sites

    International Nuclear Information System (INIS)

    Hillman, R.L.; Mohr, D.E.

    1985-01-01

    The technical DBMS is a structured and organized method for collecting, storing, retrieving, and analyzing technical data based upon standard operating procedures and quality control measures. The automated environment created by this design exists both as a repository for processing site technical data and the analysis techniques used against this data for site characterization, evaluation, and design. The system is composed of diverse technical subjects that are collectively used to address remedial action problems associated with mill tailings disposal. These technical subjects include hydrology, geology, geochemistry, radiology, and engineering

  8. FY87 scientific and technical reports, articles, papers, and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1987-01-01

    The document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY87. It also includes papers of MSFC contractors. After being announced in STAR, all of the NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, Va. 22161. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  9. FY 1988 scientific and technical reports, articles, papers and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1988-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 88. It also includes papers of MSFC contractors. After being announced in STAR, all of the NASA series reports may be obtained from the NationaL Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  10. Alcohol Fuels Program technical review, Spring 1984

    Energy Technology Data Exchange (ETDEWEB)

    1984-10-01

    The alcohol fuels program consists of in-house and subcontracted research for the conversion of lignocellulosic biomass into fuel alcohols via thermoconversion and bioconversion technologies. In the thermoconversion area, the SERI gasifier has been operated on a one-ton per day scale and produces a clean, medium-Btu gas that can be used to manufacture methanol with a relatively small gas-water shift reaction requirement. Recent research has produced catalysts that make methanol and a mixture of higher alcohols from the biomass-derived synthetic gas. Three hydrolysis processes have emerged as candidates for more focused research. They are: a high-temperature, dilute-acid, plug-flow approach based on the Dartmouth reactor; steam explosion pretreatment followed by hydrolysis using the RUT-C30 fungal organism; and direct microbial conversion of the cellulose to ethanol using bacteria in a single or mixed culture. Modeling studies, including parametric and sensitivity analyses, have recently been completed. The results of these studies will lead to a better definition of the present state-of-the-art for these processes and provide a framework for establishing the research and process engineering issues that still need resolution. In addition to these modeling studies, economic feasibility studies are being carried out by commercial engineering firms. Their results will supplement and add commercial validity to the program results. The feasibility contractors will provide input at two levels: Technical and economic assessment of the current state-of-the-art in alcohol production from lignocellulosic biomass via thermoconversion to produce methanol and higher alcohol mixtures and bioconversion to produce ethanol; and identification of research areas having the potential to significantly reduce the cost of production of alcohols.

  11. Collected software engineering papers, volume 11

    Science.gov (United States)

    1993-01-01

    This document is a collection of selected technical papers produced by participants in the Software Engineering Laboratory (SEL) from November 1992 through November 1993. The purpose of the document is to make available, in one reference, some results of SEL research that originally appeared in a number of different forums. This is the 11th such volume of technical papers produced by the SEL. Although these papers cover several topics related to software engineering, they do not encompass the entire scope of SEL activities and interests. Additional information about the SEL and its research efforts may be obtained from the sources listed in the bibliography at the end of this document.

  12. Collected software engineering papers, volume 12

    Science.gov (United States)

    1994-01-01

    This document is a collection of selected technical papers produced by participants in the Software Engineering Laboratory (SEL) from November 1993 through October 1994. The purpose of the document is to make available, in one reference, some results of SEL research that originally appeared in a number of different forums. This is the 12th such volume of technical papers produced by the SEL. Although these papers cover several topics related to software engineering, they do not encompass the entire scope of SEL activities and interests. Additional information about the SEL and its research efforts may be obtained from the sources listed in the bibliography at the end of this document.

  13. NASA/DOD Aerospace Knowledge Diffusion Research Project. Report No. 36: The Technical Communications Practices of US Aerospace Engineers and Scientists: Results of the Phase 1 NASA Langley Research Center Mail Survey

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

    1995-01-01

    The U.S. government technical report is a primary means by which the results of federally funded research and development (R&D) are transferred to the U.S. aerospace industry. However, little is known about this information product in terms of its actual use, importance, and value in the transfer of federally funded R&D. To help establish a body of knowledge, the U.S. government technical report is being investigated as part of the NASA/DOD Aerospace Knowledge Diffusion Research Project. In this report, we summarize the literature on technical reports and provide a model that depicts the transfer of federally funded aerospace R&D via the U.S. government technical report. We present results from our investigation of aerospace knowledge diffusion vis-a-vis the U.S. government technical report, and present the results of research that investigated aerospace knowledge diffusion vis-a-vis the technical communications practices of U.S. aerospace engineers and scientists who were assigned to the Research and Technology Group (RTG) at the NASA Langley Research Center in September 1995.

  14. Trust in technology a socio-technical perspective

    CERN Document Server

    Clarke, Karen; Rouncefield, Mark

    2006-01-01

    Encapsulates work done in the DIRC project (Interdisciplinary Research Collaboration in Dependability), bringing together a range of disciplinary approaches - computer science, sociology and software engineering - to produce a socio-technical systems perspective on the issues surrounding trust in technology in complex settings.

  15. Using A Model-Based Systems Engineering Approach For Exploration Medical System Development

    Science.gov (United States)

    Hanson, A.; Mindock, J.; McGuire, K.; Reilly, J.; Cerro, J.; Othon, W.; Rubin, D.; Urbina, M.; Canga, M.

    2017-01-01

    NASA's Human Research Program's Exploration Medical Capabilities (ExMC) element is defining the medical system needs for exploration class missions. ExMC's Systems Engineering (SE) team will play a critical role in successful design and implementation of the medical system into exploration vehicles. The team's mission is to "Define, develop, validate, and manage the technical system design needed to implement exploration medical capabilities for Mars and test the design in a progression of proving grounds." Development of the medical system is being conducted in parallel with exploration mission architecture and vehicle design development. Successful implementation of the medical system in this environment will require a robust systems engineering approach to enable technical communication across communities to create a common mental model of the emergent engineering and medical systems. Model-Based Systems Engineering (MBSE) improves shared understanding of system needs and constraints between stakeholders and offers a common language for analysis. The ExMC SE team is using MBSE techniques to define operational needs, decompose requirements and architecture, and identify medical capabilities needed to support human exploration. Systems Modeling Language (SysML) is the specific language the SE team is utilizing, within an MBSE approach, to model the medical system functional needs, requirements, and architecture. Modeling methods are being developed through the practice of MBSE within the team, and tools are being selected to support meta-data exchange as integration points to other system models are identified. Use of MBSE is supporting the development of relationships across disciplines and NASA Centers to build trust and enable teamwork, enhance visibility of team goals, foster a culture of unbiased learning and serving, and be responsive to customer needs. The MBSE approach to medical system design offers a paradigm shift toward greater integration between

  16. Aerospace Systems Design in NASA's Collaborative Engineering Environment

    Science.gov (United States)

    Monell, Donald W.; Piland, William M.

    1999-01-01

    Past designs of complex aerospace systems involved an environment consisting of collocated design teams with project managers, technical discipline experts, and other experts (e.g. manufacturing and systems operations). These experts were generally qualified only on the basis of past design experience and typically had access to a limited set of integrated analysis tools. These environments provided less than desirable design fidelity, often lead to the inability of assessing critical programmatic and technical issues (e.g., cost risk, technical impacts), and generally derived a design that was not necessarily optimized across the entire system. The continually changing, modern aerospace industry demands systems design processes that involve the best talent available (no matter where it resides) and access to the best design and analysis tools. A solution to these demands involves a design environment referred to as collaborative engineering. The collaborative engineering environment evolving within the National Aeronautics and Space Administration (NASA) is a capability that enables the Agency's engineering infrastructure to interact and use the best state-of-the-art tools and data across organizational boundaries. Using collaborative engineering, the collocated team is replaced with an interactive team structure where the team members are geographically distributed and the best engineering talent can be applied to the design effort regardless of physical location. In addition, a more efficient, higher quality design product is delivered by bringing together the best engineering talent with more up-to-date design and analysis tools. These tools are focused on interactive, multidisciplinary design and analysis with emphasis on the complete life cycle of the system, and they include nontraditional, integrated tools for life cycle cost estimation and risk assessment. NASA has made substantial progress during the last two years in developing a collaborative

  17. Aerospace Systems Design in NASA's Collaborative Engineering Environment

    Science.gov (United States)

    Monell, Donald W.; Piland, William M.

    2000-07-01

    Past designs of complex aerospace systems involved an environment consisting of collocated design teams with project managers, technical discipline experts, and other experts (e.g., manufacturing and systems operations). These experts were generally qualified only on the basis of past design experience and typically had access to a limited set of integrated analysis tools. These environments provided less than desirable design fidelity, often led to the inability of assessing critical programmatic and technical issues (e.g., cost, risk, technical impacts), and generally derived a design that was not necessarily optimized across the entire system. The continually changing, modern aerospace industry demands systems design processes that involve the best talent available (no matter where it resides) and access to the best design and analysis tools. A solution to these demands involves a design environment referred to as collaborative engineering. The collaborative engineering environment evolving within the National Aeronautics and Space Administration (NASA) is a capability that enables the Agency's engineering infrastructure to interact and use the best state-of-the-art tools and data across organizational boundaries. Using collaborative engineering, the collocated team is replaced with an interactive team structure where the team members are geographically distributed and the best engineering talent can be applied to the design effort regardless of physical location. In addition, a more efficient, higher quality design product is delivered by bringing together the best engineering talent with more up-to-date design and analysis tools. These tools are focused on interactive, multidisciplinary design and analysis with emphasis on the complete life cycle of the system, and they include nontraditional, integrated tools for life cycle cost estimation and risk assessment. NASA has made substantial progress during the last two years in developing a collaborative

  18. The Acoustical Presentation of Technical Information.

    Science.gov (United States)

    Barnett, George A.

    1992-01-01

    Advocates listening to technical information in much the same way as scientists and engineers look at graphics to understand the relationships among variables. Specifies a number of potential benefits of this approach. Demonstrates the presentation of acoustic information with data on the frequency of television viewing from 1950 to 1988. (SR)

  19. Separated core turbofan engine; Core bunrigata turbofan engine

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Y; Endo, M; Matsuda, Y; Sugiyama, N; Sugahara, N; Yamamoto, K [National Aerospace Laboratory, Tokyo (Japan)

    1996-04-01

    This report outlines the separated core turbofan engine. This engine is featured by parallel separated arrangement of a fan and core engine which are integrated into one unit in the conventional turbofan engine. In general, cruising efficiency improvement and noise reduction are achieved by low fan pressure ratio and low exhaust speed due to high bypass ratio, however, it causes various problems such as large fan and nacelle weight due to large air flow rate of a fan, and shift of an operating point affected by flight speed. The parallel separated arrangement is thus adopted. The stable operation of a fan and core engine is easily retained by independently operating air inlet unaffected by fan. The large degree of freedom of combustion control is also obtained by independent combustor. Fast response, simple structure and optimum aerodynamic design are easily achieved. This arrangement is also featured by flexibility of development and easy maintenance, and by various merits superior to conventional turbofan engines. It has no technological problems difficult to be overcome, and is also suitable for high-speed VTOL transport aircraft. 4 refs., 5 figs.

  20. Technical career opportunities in high-level radioactive waste management

    International Nuclear Information System (INIS)

    1993-01-01

    Technical career opportunities in high-level radioactive waste management are briefly described in the areas of: Hydrology; geology; biological sciences; mathematics; engineering; heavy equipment operation; and skilled labor and crafts

  1. Improving engineering performance by utilizing process indicators

    International Nuclear Information System (INIS)

    Roberts, T.E.

    1992-01-01

    The purpose of the work discussed in this paper was to develop engineering performance indicators used to facilitate improvement to the technical quality, cost-effectiveness, and delivery of engineering products and service. This work was specifically tailored for engineering support products and service associated with operating Florida Power and Light Company (FP and L) nuclear plants. The engineering process for the development of plant change packages was reviewed to identify critical in-process activities. Because each engineering project usually deals with a specific component or plant system, the different tasks are usually technically unique and of varying magnitudes. Although each engineering product may employ different analytical techniques or industry code requirements, several activities in documenting the engineering design process are generic. The quality of performance in these activities can be monitored analogously to the steps in a manufacturing process. This concept builds quality concepts into the package in lieu of inspecting package quality at the end of the process. The work has resulted in a valuable self-assessment tool that serves as a basis for engineering process improvements. The indicators are published in a semi-yearly performance report for FP and L contractors as well as FP and L in-house engineering work. Contracts have been set up to base fees on meeting targets established for the performance report. The ability to meet performance targets continues to improve

  2. Computer Support of Semantic Text Analysis of a Technical Specification on Designing Software

    OpenAIRE

    Zaboleeva-Zotova, Alla; Orlova, Yulia

    2009-01-01

    The given work is devoted to development of the computer-aided system of semantic text analysis of a technical specification. The purpose of this work is to increase efficiency of software engineering based on automation of semantic text analysis of a technical specification. In work it is offered and investigated a technique of the text analysis of a technical specification is submitted, the expanded fuzzy attribute grammar of a technical specification, intended for formaliza...

  3. Cytochrome P450-mediated metabolic engineering

    DEFF Research Database (Denmark)

    Renault, Hugues; Bassard, Jean-Étienne André; Hamberger, Björn Robert

    2014-01-01

    for the engineered bioproduction of such compounds. Two ground-breaking developments of commercial products driven by the engineering of P450s are the antimalarial drug precursor artemisinic acid and blue roses or carnations. Tedious optimizations were required to generate marketable products. Hurdles encountered...... in P450 engineering and their potential solutions are summarized here. Together with recent technical developments and novel approaches to metabolic engineering, the lessons from this pioneering work should considerably boost exploitation of the amazing P450 toolkit emerging from accelerated sequencing...

  4. Continuing Professional Development (CPD) of the nuclear and radiation professional engineers

    International Nuclear Information System (INIS)

    Sasaki, Satoru

    2016-01-01

    Professional Engineer is the national qualification stipulated by the Professional Engineer Act. A Professional Engineer in this Act means a person who conducts business on matters of planning, research, design, analysis, testing, evaluation or guidance thereof, which requires application of extensive scientific and technical expertise, and has three obligation and two responsibility related to engineer ethic. A technical discipline for nuclear and radiation technology in 2004, was established for the purpose of upgrading the skills of engineers in nuclear technology fields, utilizing their ability in nuclear safety regulation fields, and further strengthening safety management system in each entity. The activity of the nuclear and radiation professional engineers for the past 10 years was evaluated. For the next ten years, awareness of the role of the professional engineer to talk with general public is needed, and it is important to continue professional development. (author)

  5. Software Engineering Improvement Activities/Plan

    Science.gov (United States)

    2003-01-01

    bd Systems personnel accomplished the technical responsibilities for this reporting period, as planned. A close working relationship was maintained with personnel of the MSFC Avionics Department Software Group (ED14). Work accomplishments included development, evaluation, and enhancement of a software cost model, performing literature search and evaluation of software tools available for code analysis and requirements analysis, and participating in other relevant software engineering activities. Monthly reports were submitted. This support was provided to the Flight Software Group/ED 1 4 in accomplishing the software engineering improvement engineering activities of the Marshall Space Flight Center (MSFC) Software Engineering Improvement Plan.

  6. NASA software documentation standard software engineering program

    Science.gov (United States)

    1991-01-01

    The NASA Software Documentation Standard (hereinafter referred to as Standard) can be applied to the documentation of all NASA software. This Standard is limited to documentation format and content requirements. It does not mandate specific management, engineering, or assurance standards or techniques. This Standard defines the format and content of documentation for software acquisition, development, and sustaining engineering. Format requirements address where information shall be recorded and content requirements address what information shall be recorded. This Standard provides a framework to allow consistency of documentation across NASA and visibility into the completeness of project documentation. This basic framework consists of four major sections (or volumes). The Management Plan contains all planning and business aspects of a software project, including engineering and assurance planning. The Product Specification contains all technical engineering information, including software requirements and design. The Assurance and Test Procedures contains all technical assurance information, including Test, Quality Assurance (QA), and Verification and Validation (V&V). The Management, Engineering, and Assurance Reports is the library and/or listing of all project reports.

  7. Engineering Electricity Markets for a Decarbonized Energy System

    DEFF Research Database (Denmark)

    Jenle, Rasmus Ploug; Pallesen, Trine

    Decarbonization of the Danish electricity sector has recently been sought achieved through the introduction of a novel retail electricity market, named EcoGrid, designed to create price responsive consumers. By following the market design process undertaken by engineers at the Technical Universit...... of introducing synthetic markets as means of governance.......Decarbonization of the Danish electricity sector has recently been sought achieved through the introduction of a novel retail electricity market, named EcoGrid, designed to create price responsive consumers. By following the market design process undertaken by engineers at the Technical University...... of Denmark, the analysis addresses the question: how do engineers make markets? The answer to this question as presented here is: engineers design control systems. By tracing the origins of EcoGrid, this paper documents the governing of electricity consumers through a ‘synthetic market’, i.e. a market...

  8. A culture of technical knowledge: Professionalizing science and engineering education in late-nineteenth century America

    Science.gov (United States)

    Nienkamp, Paul

    This manuscript examines the intellectual, cultural, and practical approaches to science and engineering education as a part of the land-grant college movement in the Midwest between the 1850s and early 1900s. These land-grant institutions began and grew within unique frontier societies that both cherished self-reliance and diligently worked to make themselves part of the larger national experience. College administrators and professors encountered rapidly changing public expectations, regional needs, and employment requirements. They recognized a dire need for technically skilled men and women who could quickly adapt to changes in equipment and processes, and implement advances in scientific knowledge in American homes, fields, and factories. Charged with educating the "industrial classes in the several pursuits and professions in life," land-grant college supporters and professors sought out the most modern and innovative instructional methods. Combining the humanities, sciences, and practical skills that they believed uniquely suited student needs, these pioneering educators formulated new curricula and training programs that advanced both the knowledge and the social standing of America's agricultural and mechanical working classes.

  9. Bibliography of Lewis Research Center Technical Publications announced in 1991

    Science.gov (United States)

    1992-01-01

    This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific engineering work performed and managed by the Lewis Research Center in 1991. All the publications were announced in the 1991 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses.

  10. The Potential of the Technical University of Denmark in the Light of Sustainable Livable Cities

    DEFF Research Database (Denmark)

    Jensen, Lotte Bjerregaard; Nielsen, Per Sieverts; Nielsen, Susanne Balslev

    2014-01-01

    The Technical University of Denmark (DTU) has a long tradition for research and education in urban planning and sustainable urban development. An increasing societal focus on sustainability and urbanization in society supports this continuous focus on sustainable urban planning in technical...... educations. The focus on sustainable urban development includes understanding the role of civil engineering, water engineering, sustainable mobility and energy, and communities in developing future desirable solutions. However, beyond the challenges faced in each of the specific technical fields...... which by themselves have an impact on urban development, including water in cities, climate adaptation, mobility planning, building, energy, and community designs. A number of challenges in developing an integrated approach in the technical education are discussed in the paper. The increasing focus...

  11. Dispersion-engineered and highly-nonlinear microstructured polymer optical fibres

    DEFF Research Database (Denmark)

    Frosz, Michael Henoch; Nielsen, Kristian; Hlubina, Petr

    2009-01-01

    We demonstrate dispersion-engineering of microstructured polymer optical fibres (mPOFs) made of poly(methyl methacrylate) (PMMA). A significant shift of the total dispersion from the material dispersion is confirmed through measurement of the mPOF dispersion using white-light spectral interferome......We demonstrate dispersion-engineering of microstructured polymer optical fibres (mPOFs) made of poly(methyl methacrylate) (PMMA). A significant shift of the total dispersion from the material dispersion is confirmed through measurement of the mPOF dispersion using white-light spectral...

  12. Educating the (microwave) engineer of the future

    NARCIS (Netherlands)

    Smolders, A.B.; Vleeshouwers, J.M.

    2012-01-01

    The interest of secondary school students in science and engineering was investigated in the Netherlands. The outcome of this study shows that the technical universities are currently not very attractive for a large group of young people. Together with the requirements for the engineer of the

  13. Turning Engineering Green

    DEFF Research Database (Denmark)

    Jamison, Andrew

    2012-01-01

    Since the 1970s, the relations between engineering and development have changed significantly. On the one hand, at a discursive or macro level, there has been a shift in regard to the kind of development to which engineering is meant to contribute, from furthering economic growth to an approach...... to development that is “sustainable” in one way or another. On the other hand, on a practitioner, or micro level, there has been a change in the kinds of competence that engineers are expected to have in order to be able to contribute to development, due to the emergence of new fields of “technoscience” blurring...... the boundaries between what was previously considered science and what was previously considered technology. Finally, in between, at an institutional or meso level, there have been significant changes in how engineering work and engineering education are organized. This chapter attempts to provide an overview...

  14. Social risk assessment of large technical systems

    NARCIS (Netherlands)

    Pasman, H.J.; Vrijling, J.K.

    2003-01-01

    A probabilistic approach to engineering advances. Since risk adhering to a technical structure can be determined quantitatively easier and more accurately than before, criteria for decision making are becoming more important. If the structure is in the public domain, and benefits are not felt, the

  15. Training of engineers for Czechoslovak nuclear programme at Czech Technical University in Prague

    International Nuclear Information System (INIS)

    Klik, F.; Stoll, I.

    1983-01-01

    Between the year 1959 and the 1970's specialists for the Czechoslovak nuclear programme were only educated at the Faculty of Nuclar and Physics Engineering. In the early 1970's instruction and research related to nuclear power generation was introduced at the mechanical engineering and electrical engineering faculties. The specialization ''Nuclear power facilities'' was introduced within the study field ''Thermal and nuclear machines and equipment'' at the mechanical engineering faculty, and the electrical engineering faculty opened the study course ''Nuclear power plants'' in the study year 1975/1976. Most specialists for the nuclear programme are educated at the Faculty of Nuclear and Physics Engineering in the field ''Nuclear chemical engineering'' and in specializations ''Theory and technology of nuclear reactors'', ''Dosimetry and application of ionizing radiation'' in the study field ''Nuclear engineering''. The Faculty of Nuclear and Physics Engineering also trains specialists in the field ''Structure and materials properties'', the study courses ''Measuring technology'' and ''Control technology'' are run at the electrical engineering faculty and at the mechanical engineering faculty were introduced study courses of ''Applied mechanics'' and ''Mechanical engineering technology''. Graduates of all said study courses may be employed in the nuclear programme. (E.S.)

  16. How Engineers Make Markets Organizing Electricity System Decarbonization

    DEFF Research Database (Denmark)

    Jenle, Rasmus Ploug; Pallesen, Trine

    2017-01-01

    construction process undertaken by scientists at the Technical University of Denmark, this article shows how engineers have approached the task by designing markets as technical control systems. It is demonstrated that EcoGrid has been designed by modeling a retail electricity market on three different...... conceptions of control systems as found in the discipline of control systems engineering. By tracing the origins of EcoGrid, this article documents the governing of electricity consumers through what we here call a synthetic market, i.e. a market artifact devised to attain goals. These findings about...

  17. International Symposium on Biomedical Engineering and Medical Physics

    CERN Document Server

    Katashev, Alexei; Lancere, Linda

    2013-01-01

    This volume presents the proceedings of the International Symposium on Biomedical Engineering and Medical Physics and is dedicated to the 150 anniversary of the Riga Technical University, Latvia. The content includes various hot topics in biomedical engineering and medical physics.

  18. Power systems engineering and mathematics

    CERN Document Server

    Knight, U G

    1972-01-01

    Power Systems Engineering and Mathematics investigates the application of mathematical aids, particularly the techniques of resource planning, to some of the technical-economic problems of power systems engineering. Topics covered include the process of engineering design and the use of computers in system design and operation; power system planning and operation; time scales and computation in system operation; and load prediction and generation capacity. This volume is comprised of 13 chapters and begins by outlining the stages in the synthesis of designs (or operating states) for engineerin

  19. Geological-Technical and Geo-engineering Aspects of Dimensional Stone Underground Quarrying

    Science.gov (United States)

    Fornaro, Mauro; Lovera, Enrico

    Underground exploitation of dimensional stones is not a novelty, being long since practised, as proved by a number of historical documents and by a certain number of ancient quarrying voids throughout the world. Anyway, so far, open cast quarrying has been the most adopted practice for the excavation of dimensional stones. One primary reason that led to this situation is of course connected to the lower production costs of an open cast exploitation compared to an underground one. This cheapness has been supported by geological and technical motives: on the one hand, the relative availability of surface deposits and, on the other, the development of technologies, which often can be used only outdoor. But, nowadays, general costs of quarrying activities should be re-evaluated because new, and often proper, restrictions have been strongly rising during recent years. As a consequence of both environmental and technical restrictions, pressure will more and more arise to reduce open cast quarrying and to promote underground exploitations. The trend is already well marked for weak rocks - for instance in the extractive basin of Carrara, where about one hundred quarries are active, 30 per cent is working underground, but also in Spain, Portugal and Greece the number of underground marble quarries is increasing - but not yet for hard rock quarrying, where only few quarries are working underground all around the world. One reason has to be found in cutting technologies traditionally used. In weak rocks, diamond wire saw and chain cutter are usable, with few adaptations, in underground spaces, while drilling and blasting, the traditional exploitation method for hard stone, is not easily usable in a confined space, where often only one free face is available. Many technicians and researchers agree that two technologies will probably open the door to underground quarrying in hard rocks: diamond wire and water jet. The first one is already available; the second should still be

  20. Photovoltaic engineering handbook

    Energy Technology Data Exchange (ETDEWEB)

    Lasnier, F; Ang, T G [Asian Institute of Technolgoy, Bangkok (TH)

    1990-01-01

    The Photovoltaic Engineering Handbook is a comprehensive 'nuts and bolts' guide to photovoltaic technology and systems engineering aimed at engineers and designers in the field. It is the first book to look closely at the practical problems involved in evaluating and setting up a PV power system. The authors' comprehensive insight into the different procedures and decisions that a designer needs to make. The book is unique in its coverage and the technical information is presented in a concise and simple way to enable engineers from a wide range of backgrounds to initiate, assess, analyse and design a PV system. Energy planners making decisions on the most appropriate system for specific needs will also benefit from reading this book. Topics covered include technological processes, including solar cell technology, the photovoltaic generator, photovoltaic systems engineering; characterization and testing methods, sizing procedure; economic analysis and instrumentation. (author).

  1. Engineering education in the wake of hurricane Katrina

    Directory of Open Access Journals (Sweden)

    Lima Marybeth

    2007-10-01

    Full Text Available Abstract Living through hurricane Katrina and its aftermath and reflecting on these experiences from technical and non-technical standpoints has led me to reconsider my thoughts and philosophy on engineering education. I present three ideas regarding engineering education pedagogy that I believe will prepare future engineers for problem-solving in an increasingly complex world. They are (1 we must practice radical (to the root engineering, (2 we must illustrate connections between engineering and public policy, and (3 we will join the charge to find sustainable solutions to problems. Ideas for bringing each of these concepts into engineering curricula through methods such as case study, practicing broad information gathering and data interpretation, and other methods inside and outside the classroom, are discussed. I believe that the consequences of not considering the root issues of problems to be solved, and of not including policy and sustainability considerations when problems to be solved are framed will lead our profession toward well meaning but insufficient utility. Hurricane Katrina convinced me that we must do better as educators to prepare our students for engineering for a sustainable world.

  2. Technical engineers exchange project (coal mine technology field). Training in China; Gijutsusha koryu jigyo (tanko gijutsu bun`ya). Chugoku no kenshu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, T. [Japan Coal Energy Center, Tokyo (Japan)

    1998-07-01

    The paper described JCOAL`s project on the exchange of technical coal engineers of China. In the project on sending of engineers to China in the first term, coal mine engineers of Japan (Taiheiyo Coal Mine, Kushiro Works, Training Center) were sent to the Daitun coal-thermal power plant, Peixuan city, Jiangsu province, in September, 1997 to introduce the production control technology in Japan. They contributed to the heightening of productivity in coal mines in China. Eighteen Chinese participated in the training. Mechanization has been comparatively well in progress, and it was 83% in coal mining and 91% in drilling. The kind of coal is mostly a raw material coal. The stuff members are 30,000, and expert engineers are 4,200. The plant has an output of 130,000 kWh, owns its railroad, is run on the general multiple management, and is largely developing. The project on sending of engineers to China in the last term was carried out in February 1998 for tracing/confirming how the results of the training conducted in September are made the most of and if or not there is something bad and for obtaining the detailed data. A certain degree of promotion and effects were able to be confirmed. A project on training of the head, sub-head, etc. who were invited to Japan to lean production/management control was also carried out in November and December 1997. 1 tab.

  3. Are women engineers in Lebanon prepared for the challenges of an engineering profession?

    Science.gov (United States)

    Baytiyeh, Hoda

    2013-08-01

    This study investigates the status of women engineers in the Middle East, considering women engineers in Lebanon as a case study. The author investigated the following questions: What are the influences behind females' decisions to choose engineering as their major course of study? What are the motives behind this decision? What are the perceptions of females regarding the essential skills for a successful engineering career? An online survey consisting of Likert-scale items was completed by 327 female engineers who graduated from universities in Lebanon and now work in various locations around the world. A genuine interest in the field appeared to be the main influence in the participants' decisions to choose engineering profession. The potential for professional growth was the leading motivator for choosing engineering. Although participants reported that they possessed adequate theoretical knowledge and technical skills before graduation, in the actual practice of engineering, they noted weaknesses in creativity and innovation.

  4. Advancing the practice of systems engineering at JPL

    Science.gov (United States)

    Jansma, Patti A.; Jones, Ross M.

    2006-01-01

    In FY 2004, JPL launched an initiative to improve the way it practices systems engineering. The Lab's senior management formed the Systems Engineering Advancement (SEA) Project in order to "significantly advance the practice and organizational capabilities of systems engineering at JPL on flight projects and ground support tasks." The scope of the SEA Project includes the systems engineering work performed in all three dimensions of a program, project, or task: 1. the full life-cycle, i.e., concept through end of operations 2. the full depth, i.e., Program, Project, System, Subsystem, Element (SE Levels 1 to 5) 3. the full technical scope, e.g., the flight, ground and launch systems, avionics, power, propulsion, telecommunications, thermal, etc. The initial focus of their efforts defined the following basic systems engineering functions at JPL: systems architecture, requirements management, interface definition, technical resource management, system design and analysis, system verification and validation, risk management, technical peer reviews, design process management and systems engineering task management, They also developed a list of highly valued personal behaviors of systems engineers, and are working to inculcate those behaviors into members of their systems engineering community. The SEA Project is developing products, services, and training to support managers and practitioners throughout the entire system lifecycle. As these are developed, each one needs to be systematically deployed. Hence, the SEA Project developed a deployment process that includes four aspects: infrastructure and operations, communication and outreach, education and training, and consulting support. In addition, the SEA Project has taken a proactive approach to organizational change management and customer relationship management - both concepts and approaches not usually invoked in an engineering environment. This paper'3 describes JPL's approach to advancing the practice of

  5. A formal ontological perspective on the behaviors and functions of technical artifacts

    NARCIS (Netherlands)

    Borgo, S.; Carrara, M.; Garbacz, P.; Vermaas, P.E.

    2008-01-01

    In this paper we present a formal characterization of the engineering concepts of behavior and function of technical artifacts. We capture the meanings that engineers attach to these concepts by formalizing, within the formal ontology DOLCE, the five meanings of artifact behavior and the two

  6. Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Eggeman, Tim [ZeaChem Inc., Lakewood, CO (United States); O' Neill, Brian [ZeaChem Inc., Lakewood, CO (United States)

    2016-08-17

    ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was already in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive inhibitors

  7. Teaching and Learning in Chemical Product Engineering - an Evolving par of the Chemical Engineering Curriculum

    DEFF Research Database (Denmark)

    Vigild, Martin Etchells; Kiil, Søren; Wesselingh, Johannes

    2007-01-01

    Over the last decade Chemical Product Engineering has evolved as part of the Chemical Engineering Curriculum at several universities in Europe and America. At the DTU Chemical Product Engineering was introduced in 2000. This presentation will report on the experiences gained from teaching classes...... and preparing a text book on the subject. [1] Chemical Product Engineering is solidly based on chemical technical and engineering knowledge. Furthermore, the subject naturally calls for a holistic approach to teaching and learning and introduces elements which target transferable and professional engineering...... skills. Such skills are important in Chemical Product Engineering when dealing with open-ended problems, creative problem solutions, operating in a team working environment and exercising project management. In our course we emphasise team activites, formative feed back to the students as well as helping...

  8. Encyclopedia of earthquake engineering

    CERN Document Server

    Kougioumtzoglou, Ioannis; Patelli, Edoardo; Au, Siu-Kui

    2015-01-01

    The Encyclopedia of Earthquake Engineering is designed to be the authoritative and comprehensive reference covering all major aspects of the science of earthquake engineering, specifically focusing on the interaction between earthquakes and infrastructure. The encyclopedia comprises approximately 265 contributions. Since earthquake engineering deals with the interaction between earthquake disturbances and the built infrastructure, the emphasis is on basic design processes important to both non-specialists and engineers so that readers become suitably well-informed without needing to deal with the details of specialist understanding. The content of this encyclopedia provides technically inclined and informed readers about the ways in which earthquakes can affect our infrastructure and how engineers would go about designing against, mitigating and remediating these effects. The coverage ranges from buildings, foundations, underground construction, lifelines and bridges, roads, embankments and slopes. The encycl...

  9. Engineering models and methods for industrial cell control

    DEFF Research Database (Denmark)

    Lynggaard, Hans Jørgen Birk; Alting, Leo

    1997-01-01

    This paper is concerned with the engineering, i.e. the designing and making, of industrial cell control systems. The focus is on automated robot welding cells in the shipbuilding industry. The industrial research project defines models and methods for design and implemen-tation of computer based...... SHIPYARD.It is concluded that cell control technology provides for increased performance in production systems, and that the Cell Control Engineering concept reduces the effort for providing and operating high quality and high functionality cell control solutions for the industry....... control and monitor-ing systems for production cells. The project participants are The Danish Academy of Technical Sciences, the Institute of Manufacturing Engineering at the Technical University of Denmark and ODENSE STEEL SHIPYARD Ltd.The manufacturing environment and the current practice...

  10. Problems of standardizing and technical regulation in the electric power industry

    Science.gov (United States)

    Grabchak, E. P.

    2016-12-01

    A mandatory condition to ensure normal operation of a power system and efficiency in the sector is standardization and legal regulation of technological activities of electric power engineering entities and consumers. Compared to the times of USSR, the present-time technical guidance documents are not mandatory to follow in most cases, being of an advisory nature due to the lack of new ones. During the last five years, the industry has been showing a deterioration of the situation in terms of ensuring reliability and engineering controllability as a result of the dominant impact of short-term market stimuli and the differences in basic technological policies. In absence of clear requirements regarding the engineering aspects of such activities, production operation does not contribute to the preserving of technical integrity of the Russian power system, which leads to the loss of performance capability and controllability and causes disturbances in the power supply to consumers. The result of this problem is a high rate of accident incidence. The dynamics of accidents by the type of equipment is given, indicating a persisting trend of growth in the number of accidents, which are of a systematic nature. Several problematic aspects of engineering activities of electric power engineering entities, requiring standardization and legal regulation are pointed out: in the domestic power system, a large number of power electrotechnical and generating equipment operate along with systems of regulation, which do not comply with the principles and technical rules representing a framework where the Energy System of Russia is built and functioning

  11. Role of technical reports as a means of scientific information distribution in the field of nuclear science and technology

    International Nuclear Information System (INIS)

    Ishikawa, Masashi

    2013-06-01

    Japan Atomic Energy Agency (JAEA) has published more than twenty-thousand technical reports on the internet to provide detailed results of research and development activities. In JAEA technical reports, detailed results, experimental data, findings etc. are recorded. Technical report is effective for communication among scientists and engineers for research development in a big science like nuclear research. The number of downloads of JAEA technical reports is over 4.7 million per a year. Technical reports have many advantages for carrying research results of big projects than journal articles. It is also useful for knowledge management to transfer research results and achievements to the following generation. To improve JAEA technical reports to meet the needs of scientists and engineers and assisting the knowledge management is proposed. (author)

  12. Bibliography of Lewis Research Center technical publications announced in 1990

    Science.gov (United States)

    1991-01-01

    This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1990. All the publications were announced in the 1990 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses.

  13. Bibliography of Lewis Research Center technical publications announced in 1992

    Science.gov (United States)

    1993-01-01

    This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1992. All the publications were announced in the 1992 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses.

  14. Bibliography of Lewis Research Center technical publications announced in 1993

    Science.gov (United States)

    1994-01-01

    This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1993. All the publications were announced in the 1993 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses.

  15. Bibliography of Lewis Research Center technical publications announced in 1989

    Science.gov (United States)

    1990-01-01

    This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1989. All the publications were announced in the 1989 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses.

  16. FY 1990 scientific and technical reports, articles, papers, and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1990-01-01

    Formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY 90 are presented. Also included are papers of MSFC contractors. After being announced in STAR, all of the NASA series reports may be obtained from NTIS. The information may be of value to the scientific and engineering community in determining what information has been published and what is available.

  17. A Unique Civil Engineering Capstone Design Course

    Directory of Open Access Journals (Sweden)

    G Padmanabhan

    2018-02-01

    Full Text Available The North Dakota State University, USA, capstone course was developed as a unique model in response to the effort of the Accreditation Board of Engineering and Technology, USA, to streamline and improve design instruction in the curriculum and has steadily evolved to keep pace with the ever-changing technology and the expectations of the profession and the society we serve. A capstone design course by definition should be a design experience for students in the final year before graduation integrating all major design concepts they have learned up until then in the program. Carefully chosen real world projects with design content in all sub-disciplines of civil engineering are assigned in this team-taught course. Faculty and practicing professionals make presentations on design process; project management; leadership in an engineering environment; and public policy; global perspectives in engineering; and professional career and licensure. Practicing professionals also critique the final student presentations. Students work in teams with number of faculty serving as technical consultants, and a faculty mentor for each team to provide non-technical guidance and direction. The course requires students to demonstrate mastery of the curriculum and to work with others in a team environment. Course assessment includes evaluation of the final design, presentations, written technical reports, project design schedule, a project design journal, and reaction papers.

  18. Synthetic biology and the technicity of biofuels.

    Science.gov (United States)

    Mackenzie, Adrian

    2013-06-01

    The principal existing real-world application of synthetic biology is biofuels. Several 'next generation biofuel' companies-Synthetic Genomics, Amyris and Joule Unlimited Technologies-claim to be using synthetic biology to make biofuels. The irony of this is that highly advanced science and engineering serves the very mundane and familiar realm of transport. Despite their rather prosaic nature, biofuels could offer an interesting way to highlight the novelty of synthetic biology from several angles at once. Drawing on the French philosopher of technology and biology Gilbert Simondon, we can understand biofuels as technical objects whose genesis involves processes of concretisation that negotiate between heterogeneous geographical, biological, technical, scientific and commercial realities. Simondon's notion of technicity, the degree of concretisation of a technical object, usefully conceptualises this relationality. Viewed in terms of technicity, we might understand better how technical entities, elements, and ensembles are coming into being in the name of synthetic biology. The broader argument here is that when we seek to identify the newness of disciplines, their newness might be less epistemic and more logistic. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

  19. Encouraging the learning of hydraulic engineering subjects in agricultural engineering schools

    Science.gov (United States)

    Rodríguez Sinobas, Leonor; Sánchez Calvo, Raúl

    2014-09-01

    Several methodological approaches to improve the understanding and motivation of students in Hydraulic Engineering courses have been adopted in the Agricultural Engineering School at Technical University of Madrid. During three years student's progress and satisfaction have been assessed by continuous monitoring and the use of 'online' and web tools in two undergraduate courses. Results from their application to encourage learning and communication skills in Hydraulic Engineering subjects are analysed and compared to the initial situation. Student's academic performance has improved since their application, but surveys made among students showed that not all the methodological proposals were perceived as beneficial. Their participation in the 'online', classroom and reading activities was low although they were well assessed.

  20. Fiscal year 1993 scientific and technical reports, articles, papers, and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1993-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY93. It also includes papers of MSFC contractors. After being announced in STAR, all of the NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  1. The FY 1992 scientific and technical reports, articles, papers, and presentations

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1992-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY92. It also includes papers of MSFC contractors. After being announced in STAR, all of the NASA series reports may be obtained from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  2. Surveys on awareness and needs of industries to external accreditation system in engineer education; Gijutsusha kyoiku no gaibu ninteiseido donyu ni taisuru sangyo kai no ioshiki to needs ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In certifying the engineer educational programs at advanced educational organizations, questionnaire and visiting surveys were performed to identify the awareness and needs of industries, and reflect the results to the external accreditation system. The questionnaire survey was conducted on 1,100 engineers acting in the wide technical areas. Effective replies were obtained from 528 engineers. The visiting survey was executed on different business areas and operations. The result of the survey revealed that, in the awareness related to international universality of the engineer education and engineer qualification, 87% answered that they feel they need them, but the cognition rate on the accreditation system has not reached even 50%. In hearing the opinions from representatives in the industries, they indicated that it is not correct to link the certification course of JABEE directly to the engineer qualification; international applicability of JABEE with America is fine, but defining the engineers who desire to come from Asian countries and work in Japan is necessary; the engineer education has its importance shifting from quantity to quality and specialization, but on the other hand diversity is also demanded; and criteria would be necessary to guarantee the minimum required knowledge and capability. (NEDO)

  3. Occupational Sequences: Auto Engines 1. AT 121.

    Science.gov (United States)

    Korb, A. W.; And Others

    In an attempt to individualize an automotive course, the Vocational-Technical Division of Northern Montana College has developed Occupational Sequences for an engine rebuilding course. Occupational Sequences, a learning or teaching aid, is an analysis of numbered operations involved in engine rebuilding. Job sheets, included in the book, provide a…

  4. Digital calculations of engine cycles

    CERN Document Server

    Starkman, E S; Taylor, C Fayette

    1964-01-01

    Digital Calculations of Engine Cycles is a collection of seven papers which were presented before technical meetings of the Society of Automotive Engineers during 1962 and 1963. The papers cover the spectrum of the subject of engine cycle events, ranging from an examination of composition and properties of the working fluid to simulation of the pressure-time events in the combustion chamber. The volume has been organized to present the material in a logical sequence. The first two chapters are concerned with the equilibrium states of the working fluid. These include the concentrations of var

  5. Engineering drawing from the beginning

    CERN Document Server

    Cousins, M F

    1970-01-01

    Engineering Drawing from the Beginning, Volume 2 discusses the methods for communicating technical engineering concepts through illustrations and drawings. This volume covers the more advance techniques in engineering drawing. The coverage of the text includes the helix, which is the path traced by a point moving uniformly around the surface of a right cylinder that is moving axially. The book also covers drawings of solid objects such as prisms, pyramids, and cones, along with hollow objects made from sheet material. In Chapter 5, the text presents the conventional representations of common

  6. Department of Energy environmental management complex-wide integration using systems engineering

    International Nuclear Information System (INIS)

    Fairbourn, P.

    1997-01-01

    A systems engineering approach was successfully used to recommend changes to environmental management activities across the DOE Complex. A team of technical experts and systems engineers developed alternatives that could save tax payers billions of dollars if the barriers are removed to allow complete implementation. The alternatives are technically-based and defensible, and are being worked through the stakeholder review process. The integration process and implementing project structure are both discussed

  7. Innovative and practical technical development of nuclear energy. Efforts on proposal and recruitment type technical development of nuclear energy

    International Nuclear Information System (INIS)

    Matsui, Kazuaki; Shioiri, Akio; Hamada, Jun; Kanagawa, Takashi; Mori, Yukihide; Kouno, Koji

    2003-01-01

    In technical development of nuclear energy conceiving a view on energy environment problem at the 21st Century, technical development on innovative nuclear energy system as well as next generation LWR is an important subject. Even in Japan, on the 'Long-term program for research, development and utilization of nuclear energy (LPRNE)' summarized by the Atomic Energy Commission, investigation on R and Ds of innovative reactors under cooperation of government, industrial field, and universities is required. In the Energy Generalized Engineering Institute, by receiving a subsidy from the Ministry of Economy and Industry since 2000, a proposal recruitment business on innovative and practical technical development of nuclear energy has been carried out. Here were introduced hopeful and unique five themes out of them applied to the recruitment, such as a super-critical pressure water cooling reactor (SCPR), an integrated modular LWR (IMR): technical development for practice, technical development on general purpose boiling transitional analysis method, technical development on direct extraction of U and Pu from consumed fuels based on super-DIREX reprocessing method, and material transfer forecasting in natural barriers at landfill disposal of radioactive wastes. (G.K.)

  8. Autism spectrum disorders in relation to parental occupation in technical fields.

    Science.gov (United States)

    Windham, Gayle C; Fessel, Karen; Grether, Judith K

    2009-08-01

    A previous study reported that fathers of children with autism spectrum disorders (ASD) were more likely to work as engineers, requiring "systemizing skills," and suggesting a distinct phenotype, but alternatively this may have been related to selection biases. We conducted a population-based study to explore whether fathers, or mothers, of children with ASD are over-represented in fields requiring highly technical skills. Subjects included 284 children with ASD and 659 gender-matched controls, born in 1994 in the San Francisco Bay Area. Parental occupation and industry were abstracted verbatim from birth certificates. Engineering, computer programming, and science were examined as highly technical occupations. To limit bias by parental socio-economic status, we selected a referent group of occupations that seemed professionally similar but of a less technical nature. Odds ratios (ORs) and 95% confidence intervals (CI) were calculated by logistic regression, adjusting for parental age, education, and child race. Mothers of cases were somewhat more likely to work in hi-tech occupations (6.7%) than mothers of controls (4.0%, P=0.07), but little difference was observed among fathers, nor for engineering separately. Compared to parents in other "white collar" occupations, the adjusted OR for highly technical occupations among mothers was 2.5 (95% CI: 1.2-5.3) and among fathers was 1.3 (95% CI: 0.79-2.1), with no evidence of a joint effect observed. Our results regarding maternal occupation in technical fields being associated with ASD in offspring suggest further study to distinguish parental occupation as a phenotypic marker of genetic loading vs. other social or exposure factors.

  9. Alvar engine. An engine with variable compression ratio. Experiments and tests

    Energy Technology Data Exchange (ETDEWEB)

    Erlandsson, Olof

    1998-09-01

    This report is focused on tests with Variable Compression Ratio (VCR) engines, according to the Alvar engine principle. Variable compression ratio means an engine design where it is possible to change the nominal compression ratio. The purpose is to increase the fuel efficiency at part load by increasing the compression ratio. At maximum load, and maybe supercharging with for example turbocharger, it is not possible to keep a high compression ratio because of the knock phenomena. Knock is a shock wave caused by self-ignition of the fuel-air mix. If knock occurs, the engine will be exposed to a destructive load. Because of the reasons mentioned it would be an advantage if it would be possible to change the compression ratio continuously when the load changes. The Alvar engine provides a solution for variable compression ratio based on well-known engine components. This paper provides information about efficiency and emission characteristics from tests with two Alvar engines. Results from tests with a phase shift mechanism (for automatic compression ratio control) for the Alvar engine are also reviewed Examination paper. 5 refs, 23 figs, 2 tabs, 5 appendices

  10. FY 1995 Scientific and Technical Reports, Articles, Papers, and Presentations, Volume 1

    Science.gov (United States)

    Turner, Joyce E. (Compiler)

    1995-01-01

    This document presents formal NASA technical reports, papers published in technical journals, and presentations by MSFC personnel in FY95. It also includes papers of MSFC contractors. The information in this report may be of value to the scientific and engineering community in determining what information has been published and what is available.

  11. Technical Work Plan for: Near Field Environment: Engineered System: Radionuclide Transport Abstraction Model Report

    Energy Technology Data Exchange (ETDEWEB)

    J.D. Schreiber

    2006-12-08

    This technical work plan (TWP) describes work activities to be performed by the Near-Field Environment Team. The objective of the work scope covered by this TWP is to generate Revision 03 of EBS Radionuclide Transport Abstraction, referred to herein as the radionuclide transport abstraction (RTA) report. The RTA report is being revised primarily to address condition reports (CRs), to address issues identified by the Independent Validation Review Team (IVRT), to address the potential impact of transport, aging, and disposal (TAD) canister design on transport models, and to ensure integration with other models that are closely associated with the RTA report and being developed or revised in other analysis/model reports in response to IVRT comments. The RTA report will be developed in accordance with the most current version of LP-SIII.10Q-BSC and will reflect current administrative procedures (LP-3.15Q-BSC, ''Managing Technical Product Inputs''; LP-SIII.2Q-BSC, ''Qualification of Unqualified Data''; etc.), and will develop related Document Input Reference System (DIRS) reports and data qualifications as applicable in accordance with prevailing procedures. The RTA report consists of three models: the engineered barrier system (EBS) flow model, the EBS transport model, and the EBS-unsaturated zone (UZ) interface model. The flux-splitting submodel in the EBS flow model will change, so the EBS flow model will be validated again. The EBS transport model and validation of the model will be substantially revised in Revision 03 of the RTA report, which is the main subject of this TWP. The EBS-UZ interface model may be changed in Revision 03 of the RTA report due to changes in the conceptualization of the UZ transport abstraction model (a particle tracker transport model based on the discrete fracture transfer function will be used instead of the dual-continuum transport model previously used). Validation of the EBS-UZ interface model

  12. Engineering students and their entrepreneurial intentions

    Directory of Open Access Journals (Sweden)

    Filipa Dionísio Vieira

    2014-02-01

    Full Text Available Promoting entrepreneurship is a key opportunity in the current environment, and engineering have recognized this criticism by including in their curricula basic financial disciplines. Given the current economic situation, provide the future engineer with concepts and techniques to move from knowledge to action, can improve the value perception of entrepreneurship as an alternative to employability on behalf of others. The aim of this paper is to present the preliminary results of the ENGEmpreende survey developed to measure the perceived attitudes and values of entrepreneurship by engineering students. Our sample involves 387 students of engineering courses from University of Minho. Portuguese engineering students report good levels of thoughts about entrepreneurship. Our study also found that their entrepreneurship predisposition has dependency relationships with gender, thoughts about entrepreneurship and entrepreneurial activities. The results of the perceived image of the entrepreneur suggest that students recognize the positive image of the entrepreneur in society, but have doubts about what is best: entrepreneur or employee in a large company? As perceived barriers, engineering students perceive as difficult to find a business idea or access to bank loans. Students’ perceived skills and competence suggest a perceived high adaptability, perseverance, technical confidence and orientation to results. The results of ENGEmpreende survey give an additional contribution to the theme of engineering entrepreneurship intentions through the identification of entrepreneurship predisposition, attitude to self-employment, entrepreneurial image, barriers to entrepreneurship, risk perception and technical confidence.

  13. Research into operational parameters of diesel engines running on RME biodiesel

    Directory of Open Access Journals (Sweden)

    S. Lebedevas

    2006-12-01

    Full Text Available The results of motor experimental researches on operational parameters of diesel engines F2L511 and A41 are presented in the publication. Change of harmful emission of exhaust gases was determined and evaluated, fuel economy and thrust characteristics of diesel engines running on RME biodiesel compared to diesel fuel. The influence of technical condition of fuel injection aggregates was evaluated for parameters of harmful emission of diesel engines running on biodiesel by simulation of setback of fuel injection in alowable range of technical conditions – the coking of nozzles of fuel injector. The complex improvement of all ecological parameters was evaluated by optimisation of fuel injection phase of diesel engines running on RME biodiesel. Objectives and aspects of further researches on indicator process of diesel engines were determined.

  14. Creating the integral engineer : Combining development education, sustainability, entrepreneurship and technology at Delft University of Technology

    NARCIS (Netherlands)

    Zwarteveen, J.W.; Blom, E.M.; Vastbinder, B.; Brezet, J.C.

    2010-01-01

    A modern engineer is more than a technical specialist. Training an integral engineer requires education in non-technical skills, including social and ethical aspects. Therefore, Delft University of Technology (DUT) introduced sustainable development and entrepreneurship into its bachelor and master

  15. Engineering Probiotics that Improve Warfighter Performance by Maintaining Lean Body Mass and Inhibiting Anxiety

    Science.gov (United States)

    2017-10-03

    From - To) 03/10/2017 Final Technical Report 15-05-14 to 14-05-17 4. TITLE AND SUBTITLE Sa. CONTRACT NUMBER Engineering probiotics that improve...ABSTRACT The overall goal of this work is to engineer "synthetic probiotics": orally-administered gut bacteria that sense and compute the metabolic...Final Technical Report Grant number: ONR N00014-14-1-0487 Title: Engineering probiotics that improve warfighter performance by maintaining lean body

  16. Mesoscopic Self-Assembly: A Shift to Complexity

    Directory of Open Access Journals (Sweden)

    Massimo eMastrangeli

    2015-06-01

    Full Text Available By focusing on the construction of thermodynamically stable structures, the self-assembly of mesoscopic systems has proven capable of formidable achievements in the bottom-up engineering of micro- and nanosystems. Yet, inspired by an analogous evolution in supramolecular chemistry, synthetic mesoscopic self-assembly may have a lot more ahead, within reach of a shift toward fully three-dimensional architectures, collective interactions of building blocks and kinetic control. All over these challenging fronts, complexity holds the key.

  17. Experience with training of operating and maintenance personnel of nuclear power plants

    International Nuclear Information System (INIS)

    Pospisil, M.; Cencinger, F.

    1988-01-01

    The system is described of the specialist training of personnel for Czechoslovak nuclear power plants. Training consists of basic training, vocational training and training for the respective job. Responsible for the training is the Research Institute for Nuclear Power Plants; actual training takes place at three training centres. Personnel are divided into seven categories for training purposes: senior technical and economic staff, shift leaders, whose work has immediate effect on nuclear safety, engineering and technical personnel of technical units, shift leaders of technical units, personnel in technical units, shift service personnel and operating personnel, maintenance workers. Experience with training courses run at the training centre is summed up. Since 1980 the Centre has been training personnel mainly for the Dukovany nuclear power plant. Recommendations are presented for training personnel for the Temelin nuclear power plant. (Z.M.)

  18. TECHNICAL TRAINING SEMINAR

    CERN Multimedia

    Davide Vitè

    2002-01-01

    Wednesday 6 March TECHNICAL TRAINING SEMINAR from 9:30 to 16:45 - IT Amphitheatre - bldg. 31.3.004 Analog Devices DSP Day Thorsten Kistler (Application Engineer), Steffen Boerner (Product Specialist) / ANALOG DEVICES Munich Trying to meet your design challenges, Analog Devices compiles application information and offers chipsets, software, reference designs and mixed-signal, application specific DSPs, for a range of real-time signal processing applications. This seminar will present the latest 16bit fixed-point and 32bit floating-point DSPs (roadmaps; internal architectures, blocks, features benchmarks), with their software, development kits and emulators: Fixed-Point DSP-Family, ADSP-218x and ADSP-219x Blackfin DSP SHARC-Family, 2106x and 2116x TigerSHARC Industrial Contact: François Caloz, Sasco-Spoerle GmbH Language: English Free seminar, no registration Organiser: Davide Vitè / HR-TD / 75141 Davide.Vite@cern.ch Please read the full information on the Technical Training Seminars...

  19. A concept for a bachelor program in electrical engineering

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    2011-01-01

    The main concept for the Bachelor of Science in Engineering (BScE) in electrical engineering at Technical University of Denmark (DTU) will be described in this paper. A new curriculum was introduced from the start of the autumn semester in 2010. The curriculum was the result of more than one year...... of work with first description of competences followed by a more detailed description of the single main areas. Finally, the new study plan was implemented through a number of courses satisfying some general rules for bachelor study plans.......The main concept for the Bachelor of Science in Engineering (BScE) in electrical engineering at Technical University of Denmark (DTU) will be described in this paper. A new curriculum was introduced from the start of the autumn semester in 2010. The curriculum was the result of more than one year...

  20. Stirling engine application study

    Science.gov (United States)

    Teagan, W. P.; Cunningham, D.

    1983-01-01

    A range of potential applications for Stirling engines in the power range from 0.5 to 5000 hp is surveyed. Over one hundred such engine applications are grouped into a small number of classes (10), with the application in each class having a high degree of commonality in technical performance and cost requirements. A review of conventional engines (usually spark ignition or Diesel) was then undertaken to determine the degree to which commercial engine practice now serves the needs of the application classes and to detemine the nature of the competition faced by a new engine system. In each application class the Stirling engine was compared to the conventional engines, assuming that objectives of ongoing Stirling engine development programs are met. This ranking process indicated that Stirling engines showed potential for use in all application classes except very light duty applications (lawn mowers, etc.). However, this potential is contingent on demonstrating much greater operating life and reliability than has been demonstrated to date by developmental Stirling engine systems. This implies that future program initiatives in developing Stirling engine systems should give more emphasis to life and reliability issues than has been the case in ongoing programs.

  1. Software And Systems Engineering Risk Management

    Science.gov (United States)

    2010-04-01

    RSKM 2004 COSO Enterprise RSKM Framework 2006 ISO/IEC 16085 Risk Management Process 2008 ISO/IEC 12207 Software Lifecycle Processes 2009 ISO/IEC...1 Software And Systems Engineering Risk Management John Walz VP Technical and Conferences Activities, IEEE Computer Society Vice-Chair Planning...Software & Systems Engineering Standards Committee, IEEE Computer Society US TAG to ISO TMB Risk Management Working Group Systems and Software

  2. Chemical Engineering Division annual technical report, 1980

    International Nuclear Information System (INIS)

    Burris, L.; Webster, D.S.; Barney, D.L.; Cafasso, F.A.; Steindler, M.J.

    1981-06-01

    Highlights of the Chemical Engineering (CEN) Division's activities during 1980 are presented. In this period, CEN conducted research and development in the following areas: (1) rechargeable lithium-aluminum/iron sulfide batteries for electric vehicles and other applications; (2) ambient-temperature batteries - improved lead-acid, nickel/zinc, and nickel/iron - for electric vehicles; (3) energy-efficient industrial electrochemical processes; (4) molten carbonate fuel cells for use by electric utilities; (5) coal technology, mainly fluidized-bed combustion of coal in the presence of SO 2 sorbent of limestone; (6) heat- and seed-recovery technology for open-cycle magnetohydrodynamic systems; (7) solar energy collectors and thermal energy storage; (8) fast breeder reactor chemistry research - chemical support of reactor safety studies, chemistry of irradiated fuels, and sodium technology; (9) fuel cycle technology - management of nuclear wastes, reprocessing of nuclear fuels, and proof-of-breeding studies for the Light Water Breeder Reactor; and (10) magnetic fusion research - systems analysis and engineering experimentation, materials research, and neutron dosimetry and damage analysis. The CEN Division also has a basic energy sciences program, which includes experimental and theoretical research on (1) the catalytic hydrogenation of carbon monoxide and methanol homologation, (2) the thermodynamic properties of a wide variety of inorganic and organic materials, (3) significant mechanisms for the formation of atmospheric sulfate and nitrogen-bearing aerosols, (4) processes occurring at electrodes and in electrolytes, and (5) the physical properties of salt vapors. In addition, the Division operated the Central Analytical Chemistry Laboratory

  3. Information Engineering and Applications

    CERN Document Server

    Ma, Yan; International Conference on Information Engineering and Applications (IEA) 2011

    2012-01-01

    The International Conference on Information Engineering and Applications (IEA) 2011 will be held on October 21-24, 2011, in Chongqing, China. It is organized by Chongqing Normal University, Chongqing University, Shanghai Jiao Tong University, Nanyang Technological University, the University of Michigan, Chongqing University of Arts and Sciences, and sponsored by the National Natural Science Foundation of China. The objective of IEA 2011 is to facilitate an exchange of information on best practices for the latest research advances in the area of information engineering and intelligence applications, which mainly includes computer science and engineering, informatics, communications and control, electrical engineering, information computing, business intelligence and management. IEA 2011 will provide a forum for engineers and scientists in academia, industry, and government to address the most innovative research and development including technical challenges, social and economic issues, and to present and disc...

  4. Technical and Feasibility Analysis of Gasoline and Natural Gas Fuelled Vehicles

    Directory of Open Access Journals (Sweden)

    Charalambos Chasos

    2014-03-01

    Full Text Available There is recent interest for the utilisation of natural gas for empowering the internal combustion engines (ICE of vehicles. The production of novel natural gas ICE for vehicles, as well as the conversion of existing gasoline fuelled ICE of vehicles to natural gas fuelled ICE are new technologies which require to be analysed and assessed. The objective of the present study is to examine the adaptation of natural gas as vehicle fuel and carry out a technical analysis and an economical feasibility analysis of the two types of ICE vehicles, namely gasoline and natural gas fuelled vehicles. The technical model uses the physical properties of the two fuels and the performance factors of internal combustion engines including brake thermal efficiency. The resulting exhaust gas emissions are also estimated by the technical model using combustion calculations which provide the expected levels of exhaust gas emissions. Based on the analysis with the technical model, comparisons of the two types of engines are performed. Furthermore, the estimated performance characteristics of the two types of engines, along with local statistical data on annual fuel imports and annual fuel consumption for transportation and data on the vehicles fleet for the case study of Cyprus are used as input in the economical model. For the base year 2013, data of natural gas price is also used in the economical model. The economical model estimates the capital cost, the carbon dioxide emissions avoidance of fines, the net present value and the internal rate of return of the investment of large scale adaptation of natural gas fuelled vehicles for the case study. From the results and comparisons, conclusions are drawn and recommendations are provided for the adaptation of natural gas vehicles which can provide improved performance with reduced pollutant emissions.

  5. Professional Issues In Software Engineering

    CERN Document Server

    Bott, Frank; Eaton, Jack; Rowland, Diane

    2000-01-01

    An comprehensive text covering all the issues that software engineers now have to take into account apart from the technical side of things. Includes information on the legal, professional and commercial context in which they work.

  6. A Rule-Based Local Search Algorithm for General Shift Design Problems in Airport Ground Handling

    DEFF Research Database (Denmark)

    Clausen, Tommy

    We consider a generalized version of the shift design problem where shifts are created to cover a multiskilled demand and fit the parameters of the workforce. We present a collection of constraints and objectives for the generalized shift design problem. A local search solution framework with mul......We consider a generalized version of the shift design problem where shifts are created to cover a multiskilled demand and fit the parameters of the workforce. We present a collection of constraints and objectives for the generalized shift design problem. A local search solution framework...... with multiple neighborhoods and a loosely coupled rule engine based on simulated annealing is presented. Computational experiments on real-life data from various airport ground handling organization show the performance and flexibility of the proposed algorithm....

  7. Technical Submission Form: Technical Specification of a Wave Energy Farm.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Jesse D.; Kim Nielsen; Ben Kennedy; Bull, Diana L; Costello, Ronan Patrick; Jochem Weber

    2017-04-01

    The Wave - SPARC project developed the Technology Performance Level (TPL) assessment procedure based on a rigorous Systems Engineering exercise. The TPL assessment allows a whole system evaluation of Wave Energy Conversion Technology by measuring it against the requirements determined through the Systems Engineering exercise. The TPL assessment is intended to be useful in technology evaluation; in technology innovation; in allocation of public or priva te investment, and; in making equipment purchasing decisions. This Technical Submission Form (TSF) serves the purpose of collecting relevant and complete information, in a technology agnostic way, to allow TPL assessment s to be made by third party assessor s. The intended usage of this document is that the organization or people that are performing the role of developers or promoters of a particular technology will use this form to provide the information necessary for the organization or people who are perf orming the assessor role to use the TPL assessment.

  8. Shift Colors

    Science.gov (United States)

    Publications & News Shift Colors Pages default Sign In NPC Logo Banner : Shift Colors Search Navy Personnel Command > Reference Library > Publications & News > Shift Colors Top Link Bar Navy Personnel Library Expand Reference Library Quick Launch Shift Colors Shift Colors Archives Mailing Address How to

  9. Criticality safety engineer training at WSRC

    International Nuclear Information System (INIS)

    Williamson, T.G.; Mincey, J.F.

    1993-01-01

    Two programs designed to prepare engineers for certification as criticality safety engineers are offered at Westinghouse Savannah River Company (WSRC). One program, Student On Loan Criticality Engineer Training (SOLCET), is an intensive 2-yr course involving lectures, rigorous problem assignments, and mentoring. The other program, In-Field Criticality Engineer Training (IN-FIELD), is a less intensive series of lectures and problem assignments. Both courses are conducted by members of the Applied Physics Group (APG) of the Savannah River Technical Center, the organization at WSRC responsible for the operation and maintenance of criticality codes and for training of code users

  10. Refinement of nuclear safety education reinforcing technical succession

    International Nuclear Information System (INIS)

    Yokobori, Seiichi

    2008-01-01

    In April 2008, Musashi Institute of Technology established another faculty, the Faculty of Nuclear Safety Engineering, to educate students for nuclear engineering to meet the demands of personnel for nuclear business. At this new faculty, students mainly obtain professional knowledge and skills related to nuclear safety issues. This article described refinement of nuclear safety education by reinforcing technical succession topics, such as Rankine cycle, fission, two-phase flow, defense in depth in safety. LOCA/ECCS, seismic effects, reactor maintenance. (T. Tanaka)

  11. Identification of non-technical skills from the resilience engineering perspective: a case study of an electricity distributor.

    Science.gov (United States)

    Wachs, Priscila; Righi, Angela Weber; Saurin, Tarcisio Abreu

    2012-01-01

    Training in non-technical skills (NTS) does not usually question the design of the work system, and thus focuses narrowly on workers as the unit of analysis. This study discusses how the identification of NTS, a major step for developing an NTS training program, might be re-interpreted from the perspective of resilience engineering (RE). This discussion is based on a case study of identifying NTS for electricians who perform emergency maintenance activities in an electricity distribution power line. The results of the case study point out that four data analysis procedures might operationalize the RE perspective: (a) identifying factors that make the work difficult and which could be integrated into NTS training scenarios; (b) identifying recommendations for re-designing the system, in order either to reduce or eliminate the need for NTS; (c) classifying the NTS into pragmatic categories, which are meaningful for workers; and (d) regarding the identification of NTS as an opportunity to give visibility to adaptations carried out by workers.

  12. Evaluation of the 12-hour shift schedule at the Fast Flux Test Facility

    International Nuclear Information System (INIS)

    Lewis, P.M.; Swaim, D.J.; Rosa, R.R.; Colligan, M.J.; Booth, R.J.; Swint, M.J.

    1986-09-01

    The objective of this report are to evaluate the effect of the change to the 12-hour/day schedule on operational performance and safety of FFTF; to evaluate the degree to which the change to the 12-hour/day schedule has met its objectives; and to gather information that may be useful to FFTF management and the US Department of Energy (DOE) in evaluating 8- and 12-hour shift schedules at other facilities. The principal conclusion of this report is that the 12-hour/day shift schedule is a reasonable alternative to an 8-hour/day schedule at FFTF. As a result of the scedule change, it seems clear that plant performance improved in two ways. The operator error rate in keeping the Technical Specification Compliance Logs was already very low on the 8-hour shift. On the 12-hour shift, the rate was even lower. Also, the operator interface with craft personnel resulted in an increase in the productivity of the craft personnel

  13. Automotive Stirling engine development program: A success

    Science.gov (United States)

    Tabata, W. K.

    1987-01-01

    The original 5-yr Automotive Stirling Engine Development Program has been extended to 10 years due to reduced annual funding levels. With an estimated completion date of April 1988, the technical achievements and the prospectives of meeting the original program objectives are reviewed. Various other applications of this developed Stirling engine technology are also discussed.

  14. B 150 civil engineering futures

    DEFF Research Database (Denmark)

    Foreword B150 –Civil Engineering Futures consists of interviews made, articles written, and projects presented in connection with the 150th anniversary celebrations of the study of civil engineering in Denmark. Instead of a historical retrospect, it was decided to look into the future. What...... challenges will the next 150 years bring civil engineers? Researchers and lecturers at DTU’s Department of Civil Engineering (known as DTU Byg) suggested possible events, and we also consulted civil engineers and their business partners in the building industry. In this way, a programme was put together...... theme in twentieth century architecture. Together, civil engineer Peter Rice and architect Ian Ritchie created a paradigm shift with their revolutionary ideas for glass facades supported by cables. Glued and bolted constructions made entirely of glass are now a reality in small-scale projects, yet...

  15. Technical basis for the ITER-FEAT outline design

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-11-01

    This ITER EDA Documentation Series issue summarizes the results of the ITER Engineering Design Activities on the technical basis for the ITER-FEAT outline design. This issue also comprises some physical analysis activities as well as structure and goals of the Physics Expert Group activities.

  16. Technical basis for the ITER-FEAT outline design

    International Nuclear Information System (INIS)

    2000-01-01

    This ITER EDA Documentation Series issue summarizes the results of the ITER Engineering Design Activities on the technical basis for the ITER-FEAT outline design. This issue also comprises some physical analysis activities as well as structure and goals of the Physics Expert Group activities

  17. System Engineering and Technical Challenges Overcome in the J-2X Rocket Engine Development Project

    Science.gov (United States)

    Ballard, Richard O.

    2012-01-01

    Beginning in 2006, NASA initiated the J-2X engine development effort to develop an upper stage propulsion system to enable the achievement of the primary objectives of the Constellation program (CxP): provide continued access to the International Space Station following the retirement of the Space Station and return humans to the moon. The J-2X system requirements identified to accomplish this were very challenging and the time expended over the five years following the beginning of the J- 2X effort have been noteworthy in the development of innovations in both the fields for liquid rocket propulsion and system engineering.

  18. Observation of the Phononic Lamb Shift with a Synthetic Vacuum

    Directory of Open Access Journals (Sweden)

    T. Rentrop

    2016-11-01

    Full Text Available In contrast to classical empty space, the quantum vacuum fundamentally alters the properties of embedded particles. This paradigm shift allows one to explain the discovery of the celebrated Lamb shift in the spectrum of the hydrogen atom. Here, we engineer a synthetic vacuum, building on the unique properties of ultracold atomic gas mixtures, offering the ability to switch between empty space and quantum vacuum. Using high-precision spectroscopy, we observe the phononic Lamb shift, an intriguing many-body effect originally conjectured in the context of solid-state physics. We find good agreement with theoretical predictions based on the Fröhlich model. Our observations establish this experimental platform as a new tool for precision benchmarking of open theoretical challenges, especially in the regime of strong coupling between the particles and the quantum vacuum.

  19. Biochemical engineering's grand adventure

    NARCIS (Netherlands)

    Noorman, H.J.; Heijnen, J.J.

    2017-01-01

    Building on the recent revolution in molecular biology, enabling a wealth of bio-product innovations made from renewable feedstocks, the biotechnology field is in a transition phase to bring the products to the market. This requires a shift from natural sciences to engineering sciences with first

  20. Humanitarian engineering in the engineering curriculum

    Science.gov (United States)

    Vandersteen, Jonathan Daniel James

    There are many opportunities to use engineering skills to improve the conditions for marginalized communities, but our current engineering education praxis does not instruct on how engineering can be a force for human development. In a time of great inequality and exploitation, the desire to work with the impoverished is prevalent, and it has been proposed to adjust the engineering curriculum to include a larger focus on human needs. This proposed curriculum philosophy is called humanitarian engineering. Professional engineers have played an important role in the modern history of power, wealth, economic development, war, and industrialization; they have also contributed to infrastructure, sanitation, and energy sources necessary to meet human need. Engineers are currently at an important point in time when they must look back on their history in order to be more clear about how to move forward. The changing role of the engineer in history puts into context the call for a more balanced, community-centred engineering curriculum. Qualitative, phenomenographic research was conducted in order to understand the need, opportunity, benefits, and limitations of a proposed humanitarian engineering curriculum. The potential role of the engineer in marginalized communities and details regarding what a humanitarian engineering program could look like were also investigated. Thirty-two semi-structured research interviews were conducted in Canada and Ghana in order to collect a pool of understanding before a phenomenographic analysis resulted in five distinct outcome spaces. The data suggests that an effective curriculum design will include teaching technical skills in conjunction with instructing about issues of social justice, social location, cultural awareness, root causes of marginalization, a broader understanding of technology, and unlearning many elements about the role of the engineer and the dominant economic/political ideology. Cross-cultural engineering development

Some links on this page may take you to non-federal websites. Their policies may differ from this site.