Porous structure and surface chemistry of phosphoric acid activated carbon from corncob

International Nuclear Information System (INIS)

Sych, N.V.; Trofymenko, S.I.; Poddubnaya, O.I.; Tsyba, M.M.; Sapsay, V.I.; Klymchuk, D.O.; Puziy, A.M.

2012-01-01

Highlights: ► Phosphoric acid activation results in formation of carbons with acidic surface groups. ► Maximum amount of surface groups is introduced at impregnation ratio 1.25. ► Phosphoric acid activated carbons show high capacity to copper. ► Phosphoric acid activated carbons are predominantly microporous. ► Maximum surface area and pore volume achieved at impregnation ratio 1.0. - Abstract: Active carbons have been prepared from corncob using chemical activation with phosphoric acid at 400 °C using varied ratio of impregnation (RI). Porous structure of carbons was characterized by nitrogen adsorption and scanning electron microscopy. Surface chemistry was studied by IR and potentiometric titration method. It has been shown that porosity development was peaked at RI = 1.0 (S BET = 2081 m 2 /g, V tot = 1.1 cm 3 /g), while maximum amount of acid surface groups was observed at RI = 1.25. Acid surface groups of phosphoric acid activated carbons from corncob includes phosphate and strongly acidic carboxylic (pK = 2.0–2.6), weakly acidic carboxylic (pK = 4.7–5.0), enol/lactone (pK = 6.7–7.4; 8.8–9.4) and phenol (pK = 10.1–10.7). Corncob derived carbons showed high adsorption capacity to copper, especially at low pH. Maximum adsorption of methylene blue and iodine was observed for carbon with most developed porosity (RI = 1.0).

Porous structure and surface chemistry of phosphoric acid activated carbon from corncob

Energy Technology Data Exchange (ETDEWEB)

Sych, N.V.; Trofymenko, S.I.; Poddubnaya, O.I.; Tsyba, M.M. [Institute for Sorption and Endoecology Problems, National Academy of Sciences of Ukraine, 13 General Naumov St., 03164 Kyiv (Ukraine); Sapsay, V.I.; Klymchuk, D.O. [M.G. Kholodny Institute of Botany, National Academy of Sciences of Ukraine, 2 Tereshchenkivska St., 01601 Kyiv (Ukraine); Puziy, A.M., E-mail: alexander.puziy@ispe.kiev.ua [Institute for Sorption and Endoecology Problems, National Academy of Sciences of Ukraine, 13 General Naumov St., 03164 Kyiv (Ukraine)

2012-11-15

Highlights: Black-Right-Pointing-Pointer Phosphoric acid activation results in formation of carbons with acidic surface groups. Black-Right-Pointing-Pointer Maximum amount of surface groups is introduced at impregnation ratio 1.25. Black-Right-Pointing-Pointer Phosphoric acid activated carbons show high capacity to copper. Black-Right-Pointing-Pointer Phosphoric acid activated carbons are predominantly microporous. Black-Right-Pointing-Pointer Maximum surface area and pore volume achieved at impregnation ratio 1.0. - Abstract: Active carbons have been prepared from corncob using chemical activation with phosphoric acid at 400 Degree-Sign C using varied ratio of impregnation (RI). Porous structure of carbons was characterized by nitrogen adsorption and scanning electron microscopy. Surface chemistry was studied by IR and potentiometric titration method. It has been shown that porosity development was peaked at RI = 1.0 (S{sub BET} = 2081 m{sup 2}/g, V{sub tot} = 1.1 cm{sup 3}/g), while maximum amount of acid surface groups was observed at RI = 1.25. Acid surface groups of phosphoric acid activated carbons from corncob includes phosphate and strongly acidic carboxylic (pK = 2.0-2.6), weakly acidic carboxylic (pK = 4.7-5.0), enol/lactone (pK = 6.7-7.4; 8.8-9.4) and phenol (pK = 10.1-10.7). Corncob derived carbons showed high adsorption capacity to copper, especially at low pH. Maximum adsorption of methylene blue and iodine was observed for carbon with most developed porosity (RI = 1.0).

Pretreatment of industrial phosphoric acid by Algerian filter-aids

International Nuclear Information System (INIS)

Mellah, A.; Setti, Louisa; Chegrouche, Salah

1993-01-01

The present work involves the filtration of industrial phosphoric acid by different filter-aids such as kieselguhr, celite and bleaching clay. The retention of substances contained in wet phosphoric acid was determined using the three filter-aids. Thus, the phosphoric acid, obtained by filtration on kieselguhr has the same specifications as technical phosphoric acid produced by Rhone-Poulenc (France) as standard

Uranium recovery from wet process phosphoric acid

International Nuclear Information System (INIS)

1980-01-01

In the field of metallurgy, specifically processes for recovering uranium from wet process phosphoric acid solution derived from the acidulation of uraniferous phosphate ores, problems of imbalance of ion exchange agents, contamination of recycled phosphoric acid with process organics and oxidizing agents, and loss and contamination of uranium product, are solved by removing organics from the raffinate after ion exchange conversion of uranium to uranous form and recovery thereof by ion exchange, and returning organics to the circuit to balance mono and disubstituted ester ion exchange agents; then oxidatively stripping uranium from the agent using hydrogen peroxide; then after ion exchange recovery of uranyl and scrubbing, stripping with sodium carbonate and acidifying the strip solution and using some of it for the scrubbing; regenerating the sodium loaded agent and recycling it to the uranous recovery step. Economic recovery of uranium as a by-product of phosphate fertilizer production is effected. (author)

Phosphor investigation in the production of Syrian phosphoric acid using Nuclear Magnetic Resonance

International Nuclear Information System (INIS)

Al-Hassanieh, O.; Al-Hameish, M.

2009-06-01

Nuclear magnetic resonance spectroscopy (NMR) was applied in this work to the industrial process of extraction of uranium from phosphoric acid and to the process of the purification of the phosphoric acid for food proposes. The structural changes of used extraction materials and the organic content of the final product was studied. 13 C , 1 H and 32 P-spectra of all material during the process were recorded. The spectra of the three used extraction materials Bis(2-ethylhexyl Phosphoric Acid)) DEHPA, TriOctyl Phosphine Oxide (TOPO) (C 8 H 1 7) 3 P=O and TriButyl Phosphate (TBP) (C 4 H 9 O) 3 P=O show a partial degradation during the process. The final product ( Phosphoric acid for Food proposes) doesn't contain any organic solvents or extraction material. (author)

Adsorption of volatile organic compounds by pecan shell- and almond shell-based granular activated carbons.

Science.gov (United States)

Bansode, R R; Losso, J N; Marshall, W E; Rao, R M; Portier, R J

2003-11-01

The objective of this research was to determine the effectiveness of using pecan and almond shell-based granular activated carbons (GACs) in the adsorption of volatile organic compounds (VOCs) of health concern and known toxic compounds (such as bromo-dichloromethane, benzene, carbon tetrachloride, 1,1,1-trichloromethane, chloroform, and 1,1-dichloromethane) compared to the adsorption efficiency of commercially used carbons (such as Filtrasorb 200, Calgon GRC-20, and Waterlinks 206C AW) in simulated test medium. The pecan shell-based GACs were activated using steam, carbon dioxide or phosphoric acid. An almond shell-based GAC was activated with phosphoric acid. Our results indicated that steam- or carbon dioxide-activated pecan shell carbons were superior in total VOC adsorption to phosphoric acid-activated pecan shell or almond shell carbons, inferring that the method of activation selected for the preparation of activated carbons affected the adsorption of VOCs and hence are factors to be considered in any adsorption process. The steam-activated, pecan shell carbon adsorbed more total VOCs than the other experimental carbons and had an adsorption profile similar to the two coconut shell-based commercial carbons, but had greater adsorption than the coal-based commercial carbon. All the carbons studied adsorbed benzene more effectively than the other organics. Pecan shell, steam-activated and acid-activated GACs showed higher adsorption of 1,1,1-trichloroethane than the other carbons studied. Multivariate analysis was conducted to group experimental carbons and commercial carbons based on their physical, chemical, and adsorptive properties. The results of the analysis conclude that steam-activated and acid-activated pecan shell carbons clustered together with coal-based and coconut shell-based commercial carbons, thus inferring that these experimental carbons could potentially be used as alternative sources for VOC adsorption in an aqueous environment.

Electrolyte Additives for Phosphoric Acid Fuel Cells

DEFF Research Database (Denmark)

Gang, Xiao; Hjuler, H.A.; Olsen, C.A.

1993-01-01

, as a fuel-cell performance with the modified electrolytes. Specific conductivity measurements of some of the modified phosphoric acid electrolytes are reported. At a given temperature, the conductivity of the C4F9SO3K-modified electrolyte decreases with an increasing amount of the additive; the conductivity...... of the remains at the same value as the conductivity of the pure phosphoric acid. At a given composition, the conductivity of any modified electrolyte increases with temperature. We conclude that the improved cell performance for modified electrolytes is not due to any increase in conductivity.......Electrochemical characteristics of a series of modified phosphoric acid electrolytes containing fluorinated car on compounds and silicone fluids as additives are presented. When used in phosphoric acid fuel cells, the modified electrolytes improve the performance due to the enhanced oxygen...

Method of recovering phosphoric acid type decontaminating electrolytes by electrodeposition

International Nuclear Information System (INIS)

Sasaki, Takashi; Wada, Koichi; Kobayashi, Toshio.

1985-01-01

Purpose: To recoving phosphoric acid type highly concentrated decontaminating liquid used for the electrolytic decontamination of contaminated equipments, components, etc in nuclear power plants or the like through electrodeposition by diaphragm electrolysis. Method: Before supplying phosphoric acid decontaminating liquid at high concentration used in the electrolytic decontaminating step to an electrodeposition recovering tank, phosphoric acid in the decontaminating electrolyte is extracted with solvents and decomposed liquid extracts (electrolyte reduced with the phosphoric acid component) are supplied to the cathode chamber of the electrodeposition recovering tank, where phosphoric acid is back-extracted with water from the solvents after extraction of phosphoric acid. Then, the back-extracted liquids (aqueous phosphoric acid solution scarcely containing metal ions) are sent to the anode chamber of the electrodeposition recovering tank. Metal ions in the liquid are captured by electrodeposition in the cathode chamber, as well as phosphoric acid in the liquids is concentrated to the initial concentration of the electrolyte in the anode chamber for reuse as the decontaminating electrolyte. As the phosphoric acid extracting agent used in the electrodeposition recovering step for the decontaminating electrolyte, water-insoluble and non-combustible tributyl phosphate (TBP) is most effective. (Horiuchi, T.)

Uranium recovery from wet process phosphoric acid

International Nuclear Information System (INIS)

Carrington, O.F.; Pyrih, R.Z.; Rickard, R.S.

1981-01-01

Improvement in the process for recovering uranium from wetprocess phosphoric acid solution derived from the acidulation of uraniferous phosphate ores by the use of two ion exchange liquidliquid solvent extraction circuits in which in the first circuit (A) the uranium is reduced to the uranous form; (B) the uranous uranium is recovered by liquid-liquid solvent extraction using a mixture of mono- and di-(Alkyl-phenyl) esters of orthophosphoric acid as the ion exchange agent; and (C) the uranium oxidatively stripped from the agent with phosphoric acid containing an oxidizing agent to convert uranous to uranyl ions, and in the second circuit (D) recovering the uranyl uranium from the strip solution by liquid-liquid solvent extraction using di(2ethylhexyl)phosphoric acid in the presence of trioctylphosphine oxide as a synergist; (E) scrubbing the uranium loaded agent with water; (F) stripping the loaded agent with ammonium carbonate, and (G) calcining the formed ammonium uranyl carbonate to uranium oxide, the improvement comprising: (1) removing the organics from the raffinate of step (B) before recycling the raffinate to the wet-process plant, and returning the recovered organics to the circuit to substantially maintain the required balance between the mono and disubstituted esters; (2) using hydogren peroxide as the oxidizing agent in step (C); (3) using an alkali metal carbonate as the stripping agent in step (F) following by acidification of the strip solution with sulfuric acid; (4) using some of the acidified strip solution as the scrubbing agent in step (E) to remove phosphorus and other impurities; and (5) regenerating the alkali metal loaded agent from step (F) before recycling it to the second circuit

Process for winning uranium from wet process phosphoric acid

International Nuclear Information System (INIS)

1980-01-01

A process is described for winning uranium from wet process phosphoric acid by means of liquid-liquid extraction with organic phosphoric acid esters. The process is optimised by keeping the sulphate percentage in the phosphoric acid below 2% by weight, and preferably below 0.6% by weight, as compared to P 2 O 5 in the phosphoric acid. This is achieved by adding an excess of Ba and/or Ca carbonate or sulfide solution and filtering off the formed calcium and/or barium sulphate precipitates. Solid KClO 3 is then added to the filtrate to oxidise U 4+ to U 6+ . The normal extraction procedure using organic phosphoric esters as extraction liquid, can then be applied. (Th.P.)

Investigation of the synergic effect of some neutral organophosphoric compounds on the extraction of uranium from phosphoric acid solutions by D1-(2-Ethyl Hexyl) phosphoric acid

International Nuclear Information System (INIS)

Stas, J.; Khorfan, S.; Koudsi, Y.

1998-05-01

The extraction of uranium (VI) from pure phosphoric acid media by D2EHPA/Kerosene has been studied. The mechanism of the extraction was found as follows: The logarithm of the equilibrium constant of the extraction (LogKex) was found (3.06), (3.32), (3.24), (3.3) for the following phosphoric acid concentrations respectively (1), (2), (3), (4) Mol/1, and the enthalpy change DELTA H was found (-100.68 kj/mol). (-76 kj/mol) for (1), (2) mol/1 phosphoric acid concentrations. The synergic effect of TOPO, TBP, and TBPI with DEHPA have been studied during the extraction of uranium from pure phosphoric acid and Syrian commercial phosphoric acid. The synergic effect increases as follows: TBP< TBPI<< TOPO (In pure phosphoric acid), TBPI approx TBP<< TOPO (In Syrian commercial phosphoric acid). The difficulty of extracting uranium (VI) from Syrian commercial phosphoric acid in comparison with pure phosphoric acid is due to the presence of several impurities capable of complexing uranium, and a small amounts of solid and organic matters, all these are factors which reduce the distribution coefficient of uranium. (Author)

Recuperation of uranium from phosphoric acid

International Nuclear Information System (INIS)

Cordero, G.; Jodra, L.G.; Otero, J.L.; Josa, J.M.

1977-01-01

The Spanish capacity for phosphoric acid production is 500.000 t P 2 O 5 /yr. This acid has an average concentration of 365 g U 3 O 8 / t P 2 O 5 . Therefore about 180 t U 3 O 8 /yr are dissolved. In 1969, the Junta de Energia Nuclear (JEN) developed, in bench scale, a solvent extraction process to recover the uranium from the phosphoric acid. The solvent used was a synergistic mixture of D2EHPA and TOPO. The results were very promising with good recovery and very high quality for the uranium concentrate. Later, the J.E.N. continued the studies in a pilot plant scale. For this purpose, was built an experimental facility in Huelva; it can treat about 7 cu. m/day of brown acid. Fosforico Espanol, S.A. (FESA) collaborated in the studies and agreed to setting up these installations in their factory. They also provided fresh phosphoric acid for the tests. In this pilot plant we studied the following stages: a) Clarification and conditioning of the phosphoric acid; b) Uranium extraction followed by stripping in a reducing medium; c) Purification by extraction and washing; d) Obtention of the concentrate by stripping with ammonia and CO 2 gas, followed by crystallization of the ammonium uranyl tricarbonate (AUT); and e) Calcination of the concentrate to decompose the AUT to uranium oxides. The results confirmed the laboratory test data. Recuperation levels were between 85 and 90%. The AUT calcined at 550 0 C. gave a product with 96-98% U 3 O 8 . In view of the pilot plant results we have prepared a black book for an industrial plant to treat about 3700 cu. m/day of phosphoric acid. At the present time the financial aspects of this installation are being studied [es

Phosphates and phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Becker, P [Compagnie Francaise de l' Azote, Paris (France)

1983-01-01

In chapter 8.5 the following aspects of uranium recovery are treated: basis of extraction process, extraction principle, solvents, strength of the acid to be treated, technology, main processes in use, impact of uranium recovery on phosphoric acid plants, and economics of uranium recovery plants.

Preliminary study on preparation of BCNO phosphor particles using citric acid as carbon source

Energy Technology Data Exchange (ETDEWEB)

Nuryadin, Bebeh W.; Pratiwi, Tripuspita; Faryuni, Irfana D.; Iskandar, Ferry, E-mail: ferry@fi.itb.ac.id; Abdullah, Mikrajuddin; Khairurrijal [Department of Physics, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Ganesha 10 Bandung, Indonesia 40132 (Indonesia); Ogi, Takashi; Okuyama, Kikuo [Department of Chemical Engineering, Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi Hiroshima, Japan 739-8527 (Japan)

2015-04-16

A citric acid was used as a carbon source in the preparation of boron carbon oxy-nitride (BCNO) phosphor particles by a facile process. The preparation process was conducted at relatively low temperature 750 °C and at ambient pressure. The prepared BCNO phosphors showed a high photoluminescence (PL) performance at peak emission wavelength of 470 nm under excitation by a UV light 365 nm. The effects of carbon/boron and nitrogen/boron molar ratios on the PL properties were also investigated. The result showed that the emission spectra with a wavelength peak ranging from 444 nm to 496 nm can be obtained by varying carbon/boron ratios from 0.1 to 0.9. In addition, the observations showed that the BCNO phosphor material has two excitation peaks located at the 365 nm (UV) and 420 nm (blue). Based on these observations, we believe that the citric acid derived BCNO phosphor particles can be a promising inexpensive material for phosphor conversion-based white LED.

Purification of di-nonyl phenyl phosphoric acid (DNPPA) for synergistic extraction of uranium from strong phosphoric acid

International Nuclear Information System (INIS)

Singh, D.K.; Vijayalakshmi, R.; Singh, H.; Sharma, J.N.; Ruhela, R.

2009-01-01

Di-nonyl phenyl phosphoric acid (DNPPA) obtained from various synthesis methods is always associated with impurities such as mono-nonyl phenyl phosphoric acid and nonyl phenol which need to be separated for its effective use in the extraction of uranium from strong phosphoric acid. Two methods of purification namely liquid-solid separation method using neodymium salt and liquid-liquid separation method using methylene glycol have been described. In the liquid solid separation method the purity of DNPPA obtained was about 95% with less than 1.0% monoester, however it heavily suffers in the recovery aspect which is of the order of 50-60%. The methylene glycol treatment method, results in high purity and recovery of the product. Purity obtained was about 95.0% diester and less than 0.5% monoester and recovery was more than 90%. Analysis of DNPPA was done by potentiometric titration method using autotitrator. (author)

Separation of rare earths from solutions of phosphoric acid

International Nuclear Information System (INIS)

Jones, E.A.

1977-01-01

Rare earths are separated from 6M phosphoric acid by adsorption onto cation resin BIORAD AG50W-X8. The phosphoric acid is then washed from the column, and the rare earths are eluted with 4M hydrochloric acid

Process for recovering yttrium and lanthanides from wet-process phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Janssen, J.A.; Weterings, C.A.

1983-06-28

Process for recovering yttrium and lanthanides from wet-process phosphoric acid by adding a flocculant to the phosphoric acid, separating out the resultant precipitate and then recovering yttrium and lanthanides from the precipitate. Uranium is recovered from the remaining phosphoric acid.

Removal of Heavy Metal Ions with Acid Activated Carbons Derived from Oil Palm and Coconut Shells

Science.gov (United States)

Rahman, Mokhlesur M.; Adil, Mohd; Yusof, Alias M.; Kamaruzzaman, Yunus B.; Ansary, Rezaul H.

2014-01-01

In this work, batch adsorption experiments were carried out to investigate the suitability of prepared acid activated carbons in removing heavy metal ions such as nickel(II), lead(II) and chromium(VI). Acid activated carbons were obtained from oil palm and coconut shells using phosphoric acid under similar activation process while the differences lie either in impregnation condition or in both pretreatment and impregnation conditions. Prepared activated carbons were modified by dispersing hydrated iron oxide. The adsorption equilibrium data for nickel(II) and lead(II) were obtained from adsorption by the prepared and commercial activated carbons. Langmuir and Freundlich models fit the data well. Prepared activated carbons showed higher adsorption capacity for nickel(II) and lead(II). The removal of chromium(VI) was studied by the prepared acid activated, modified and commercial activated carbons at different pH. The isotherms studies reveal that the prepared activated carbon performs better in low concentration region while the commercial ones in the high concentration region. Thus, a complete adsorption is expected in low concentration by the prepared activated carbon. The kinetics data for Ni(II), Pb(II) and Cr(VI) by the best selected activated carbon fitted very well to the pseudo-second-order kinetic model. PMID:28788640

Removal of Heavy Metal Ions with Acid Activated Carbons Derived from Oil Palm and Coconut Shells

Directory of Open Access Journals (Sweden)

Mokhlesur M. Rahman

2014-05-01

Full Text Available In this work, batch adsorption experiments were carried out to investigate the suitability of prepared acid activated carbons in removing heavy metal ions such as nickel(II, lead(II and chromium(VI. Acid activated carbons were obtained from oil palm and coconut shells using phosphoric acid under similar activation process while the differences lie either in impregnation condition or in both pretreatment and impregnation conditions. Prepared activated carbons were modified by dispersing hydrated iron oxide. The adsorption equilibrium data for nickel(II and lead(II were obtained from adsorption by the prepared and commercial activated carbons. Langmuir and Freundlich models fit the data well. Prepared activated carbons showed higher adsorption capacity for nickel(II and lead(II. The removal of chromium(VI was studied by the prepared acid activated, modified and commercial activated carbons at different pH. The isotherms studies reveal that the prepared activated carbon performs better in low concentration region while the commercial ones in the high concentration region. Thus, a complete adsorption is expected in low concentration by the prepared activated carbon. The kinetics data for Ni(II, Pb(II and Cr(VI by the best selected activated carbon fitted very well to the pseudo-second-order kinetic model.

Porous structure and surface chemistry of phosphoric acid activated carbon from corncob

Science.gov (United States)

Sych, N. V.; Trofymenko, S. I.; Poddubnaya, O. I.; Tsyba, M. M.; Sapsay, V. I.; Klymchuk, D. O.; Puziy, A. M.

2012-11-01

Active carbons have been prepared from corncob using chemical activation with phosphoric acid at 400 °C using varied ratio of impregnation (RI). Porous structure of carbons was characterized by nitrogen adsorption and scanning electron microscopy. Surface chemistry was studied by IR and potentiometric titration method. It has been shown that porosity development was peaked at RI = 1.0 (SBET = 2081 m2/g, Vtot = 1.1 cm3/g), while maximum amount of acid surface groups was observed at RI = 1.25. Acid surface groups of phosphoric acid activated carbons from corncob includes phosphate and strongly acidic carboxylic (pK = 2.0-2.6), weakly acidic carboxylic (pK = 4.7-5.0), enol/lactone (pK = 6.7-7.4; 8.8-9.4) and phenol (pK = 10.1-10.7). Corncob derived carbons showed high adsorption capacity to copper, especially at low pH. Maximum adsorption of methylene blue and iodine was observed for carbon with most developed porosity (RI = 1.0).

Uranium extraction in phosphoric acid

International Nuclear Information System (INIS)

Araujo Figueiredo, C. de

1984-01-01

Uranium is recovered from the phosphoric liquor produced from the concentrate obtained from phosphorus-uraniferous mineral from Itataia mines (CE, Brazil). The proposed process consists of two extraction cycles. In the first one, uranium is reduced to its tetravalent state and then extracted by dioctylpyrophosphoric acid, diluted in Kerosene. Re-extraction is carried out with concentrated phosphoric acid containing an oxidising agent to convert uranium to its hexavalent state. This extract (from the first cycle) is submitted to the second cycle where uranium is extracted with DEPA-TOPO (di-2-hexylphosphoric acid/tri-n-octyl phosphine oxide) in Kerosene. The extract is then washed and uranium is backextracted and precipitated as commercial concentrate. The organic phase is recovered. Results from discontinuous tests were satisfactory, enabling to establish operational conditions for the performance of a continuous test in a micro-pilot plant. (Author) [pt

Recovering of uranium from phosphoric acid produced by the wet process

International Nuclear Information System (INIS)

Barreiro, A.J.; Lyon, W.L.; Holleman, R.A.; Randell, C.C.

1977-01-01

Process for recovering uranium as from an aqueous solution of phosphoric acid arising from a wet process, with a scrubbing agent essentially composed of a hydrocarbon whose boiling point is situated between 150 0 C and 300 0 C, which reacts with the contaminents formed in the sludge in the phosphoric acid, in an efficient enough quantity to wash the contamination products forming the phosphoric acid sludge, give a sludge phase and a purified phosphoric acid phase, after which the sludge phase is extracted [fr

Uranium recovery from wet-process phosphoric acid with octylphenyl acid phosphate. Progress report

International Nuclear Information System (INIS)

Arnold, W.D.; McKamey, D.R.; Baes, C.F.

1980-01-01

Studies were continued of a process for recovering uranium from wet-process phosphoric acid with octylphenyl acid phosphate (OPAP), a mixture of mono- and dioctylphenyl phosphoric acids. The mixture contained at least nine impurities, the principal one being octyl phenol, and also material that readily hydrolyzed to octyl phenol and orthophosphoric acid. The combination of mono- and dioctylphenyl phosphoric acids was the principal uranium extractant, but some of the impurities also extracted uranium. Hydrolysis of the extractant had little effect on uranium extraction, as did the presence of moderate concentrations of octyl phenol and trioctylphenyl phosphate. Diluent choice among refined kerosenes, naphthenic mixtures, and paraffinic hydrocarbons also had little effect on uranium extraction, but extraction was much lower when an aromatic diluent was used. Purified OPAP fractions were sparingly soluble in aliphatic hydrocarbon diluents. The solubility was increased by the presence of impurities such as octyl phenol, and by the addition of water or an acidic solution to the extractant-diluent mixture. In continuous stability tests, extractant loss by distribution to the aqueous phase was much less to wet-process phosphoric acid than to reagent grade acid. Uranium recovery from wet-process acid decreased steadily because of the combined effects of extractant poisoning and precipitation of the extractant as a complex with ferric iron. Unaccountable losses of organic phase volume occurred in the continuous tests. While attempts to recover the lost organic phase were unsuccessful, the test results indicate it was not lost by entrainment or dissolution in the phosphoric acid solutions. 21 figures, 8 tables

World wide IFC phosphoric acid fuel cell implementation

Energy Technology Data Exchange (ETDEWEB)

King, J.M. Jr

1996-04-01

International Fuel Cells, a subsidary of United technologies Corporation, is engaged in research and development of all types of fuel cell technologies and currently manufactures alkaline fuel cell power plants for the U.S. manned space flight program and natural gas fueled stationary power plants using phosphoric acid fuel cells. This paper describes the phosphoric acid fuel cell power plants.

Method for the recovery of uranium from a concentrate using pure phosphoric acid

International Nuclear Information System (INIS)

1980-01-01

Procedure for the recovery of an uranium bearing concentrate and pure phosphoric acid from a wet process phosphoric acid from the treatment fluid with a precipitation means in conjunction with an organic diluent, the thus formed precipitate to separate and from the remaining mixture of phosphoric acid and diluent the phosphoric acid to extract, characterised in that one applies an inorganic fluorine compound. (G.C.)

Transport of phosphoric acid through supported liquid membrane

International Nuclear Information System (INIS)

Zayzafoon, G.; Yassine, T.; Baidoun, R.

2003-01-01

The transport of phosphhoric acid through liquid membranes of amylalkohol, 1-octanol and 2-octanol was studied. It was found that phosphoric acid is transfered from feed side to strip side and the transport increased with the concentration of phosphoric acid up to 5M. The permeability in each membrane was determined for 5M phosphoic acid. It was found that the permeability values are 1.45 x 10 1 0 m 2 s 1 for amylakohol and ∼ 1x10 1 0 m 2 s 1 for each of 1-octanol and 2-octanol

Initiation in the study of uranium recovery from the phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Anchondo Adalid, J M

1974-01-01

The loss of considerable amounts of uranium in the Mexican phosphoric acid industry makes it important to study economic methods of recovery; the studies can serve as a basis for the construction and operation of a pilot plant as a normal preliminary to larger-scale projects. Routine experimental techniques for solvent extraction were employed. Extraction efficiencies of the order of 90-95% were obtained using 0.09-0.18M solutions of a mixture of phosphoric octyl esters applied to 4 and 6M solutions of phosphoric acid (reagent grade) containing uranium in concentrations of 0.05-0.50g of U/sub 3/O/sub 8/ per litre of acid. The conclusion was reached that phosphoric octyl esters can be used for recovering uranium in satisfactory quantities from phosphoric acid solutions by means of solvent extraction, and that the uranium can be separated from the solvent by the established procedures.

Initiation in the study of uranium recovery from the phosphoric acid

International Nuclear Information System (INIS)

Anchondo Adalid, J.M.

1974-01-01

The loss of considerable amounts of uranium in the Mexican phosphoric acid industry makes it important to study economic methods of recovery; the studies can serve as a basis for the construction and operation of a pilot plant as a normal preliminary to larger-scale projects. Routine experimental techniques for solvent extraction were employed. Extraction efficiencies of the order of 90-95% were obtained using 0.09-0.18M solutions of a mixture of phosphoric octyl esters applied to 4 and 6M solutions of phosphoric acid (reagent grade) containing uranium in concentrations of 0.05-0.50g of U 3 O 8 per litre of acid. The conclusion was reached that phosphoric octyl esters can be used for recovering uranium in satisfactory quantities from phosphoric acid solutions by means of solvent extraction, and that the uranium can be separated from the solvent by the established procedures. (author)

Technology of uranium recovery from wet-process phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Inoue, Katsutoshi [Saga Univ. (Japan). Faculty of Science and Engineering; Nakashio, Fumiyuki

1982-12-01

Rock phosphate contains from 0.005 to 0.02 wt.% of uranium. Though the content is a mere 5 to 10 % of that in uranium ore, the total recovery of uranium is significant since it is used for fertilizer manufacture in a large quantity. Wet-process phosphoric acid is produced by the reaction of rock phosphate with sulfuric acid. The recovery of uranium from this phosphoric acid is mostly by solvent extraction at present. According to U/sup 4 +/ or UO/sub 2//sup 2 +/ as the form of its existence, the technique of solvent extraction differs. The following matters are described: processing of rock phosphate; recovery techniques including the extraction by OPPA-octyl pyrophosphoric acid for U/sup 4 +/, and by mixed DEHPA-Di-(2)-ethylhexyl phosphoric acid and TOPO-tryoctyl phosphine oxide for UO/sub 2//sup 2 +/, and by OPAP-octylphenyl acid phosphate for U/sup 4 +/; the recent progress of the technology as seen in patents.

Study of a Triazole Derivative as Corrosion Inhibitor for Mild Steel in Phosphoric Acid Solution

Directory of Open Access Journals (Sweden)

Lin Wang

2012-01-01

Full Text Available The corrosion inhibition by a triazole derivative (PAMT on mild steel in phosphoric acid (H3PO4 solution has been investigated by weight loss and polarization methods. The experimental results reveal that the compound has a significant inhibiting effect on the corrosion of steel in H3PO4 solution. It also shows good corrosion inhibition at higher concentration of H3PO4. Potentiodynamic polarization studies have shown that the compound acts as a mixed-type inhibitor retarding the anodic and cathodic corrosion reactions with predominant effect on the cathodic reaction. The values of inhibition efficiency obtained from weight loss and polarization measurements are in good agreement. The adsorption of this compound is found to obey the Langmuir adsorption isotherm. Some kinetic and thermodynamic parameters such as apparent activation energy, frequency factor, and adsorption free energy have been calculated and discussed.

Method for separating mono- and di-octylphenyl phosphoric acid esters

International Nuclear Information System (INIS)

Arnold, W.D. Jr.

1977-01-01

A method for separating mono-octylphenyl phosphoric acid ester and di-octylphenyl phosphoric acid ester from a mixture thereof comprises reacting the ester mixture with a source of lithium or sodium ions to form a mixture of the phosphate salts; contacting the salt mixture with an organic solvent which causes the dioctylphenyl phosphate salt to be dissolved in the organic solvent phase and the mono-octylphenyl phosphate salt to exist in a solid phase; separating the phases; recovering the phosphate salts from their respective phases; and acidifying the recovered salts to form the original phosphoric acid esters

Promotion of Crystal Growth on Biomass-based Carbon using Phosphoric Acid Treatments

Directory of Open Access Journals (Sweden)

Liwei Yu

2015-02-01

Full Text Available The effect of phosphoric acid treatments on graphitic microcrystal growth of biomass-based carbons was investigated using X-ray diffraction, infrared spectroscopy, and Raman spectroscopy. Although biomass-based carbons are believed to be hard to graphitize even after heat treatments well beyond 2000 °C, we found that graphitic microcrystals of biomass-based carbons were significantly promoted by phosphoric acid treatments above 800 °C. Moreover, twisted spindle-like whiskers were formed on the surface of the carbons. This suggests that phosphorus-containing groups turn graphitic microcrystalline domains into graphite during phosphoric acid treatments. In addition, the porous texture of the phosphoric acid-treated carbon has the advantage of micropore development.

Process for recovery of uranium from wet process phosphoric acid

International Nuclear Information System (INIS)

Wiewiorowski, T.K.; Thornsberry, W.L. Jr.

1978-01-01

Process is claimed for the recovery of uranium from wet process phosphoric acid solution in which an organic extractant, containing uranium values and dissolved iron impurities and comprising a dialkylphosphoric acid and a trialkylphosphine oxide dissolved in a water immiscible organic solvent, is contacted with a substantially iron-free dilute aqueous phosphoric acid to remove said iron impurities. The removed impurities are bled from the system by feeding the resulting iron-loaded phosphoric acid to a secondary countercurrent uranium extraction operation from which they leave as part of the uranium-depleted acid raffinate. Also, process for recovering uranium in which the extractant, after it has been stripped of uranium values by aqueous ammonium carbonate, is contacted with a dilute aqueous acid selected from the group consisting of H 2 SO 4 , HCl, HNO 3 and iron-free H 3 PO 4 to improve the extraction efficiency of the organic extractant

Flocculation of suspended matter in a crude wet phosphoric acid (Algeria)

International Nuclear Information System (INIS)

Brikci Nigassa, M.; Bensebaa, A.

1994-11-01

Prior to the recovery of uranium, a pre-treatment of the phosphoric acid is necessary to remove soluble impurities of different origins. In this work, synthetic flocculants have been used. the influence of operating conditions on flocculation and filtration, such as, type of flocculants, polymer concentration, temperature, mixing and time of agitation, has been studied for both aged and fresh phosphoric acid. It has been shown that synthetic flocculants can be used for flocculation ins a phosphoric acid medium and that flocculation and filtration processes are strongly linked

Cadmium elemination from phosphoric acid by ionic flotation

International Nuclear Information System (INIS)

Brikci-Nigassa, Mounir; Hamouche, Hafida

1995-11-01

The ion flotation process for the recovery of cadmium from wet phosphoric acid (30%P2O5) has been studied. This technique combines a chemical recation between the collector and the cadmium to form a precipitate (sublate) which is carried to the surface of the solution by air bubbles. the resulting foam containing the cadmium may then separated from solution. The influence of parameters such as collector and cadmium concentration as well as iron content have been investigated for the case a synthetic acid (30% P2O5). The result have been applied to the industrial phosphoric acid produced from Djebel Onk's phosphates (Algeria)

Oxidation-extraction of uranium from wet-process phosphoric acid

International Nuclear Information System (INIS)

Lawes, B.C.

1985-01-01

The invention involves an improvement to the reductive stripping process for recovering uranium values from wet-process phosphoric acid solution, where uranium in the solution is oxidized to uranium (VI) oxidation state and then extracted from the solution by contact with a water immiscible organic solvent, by adding sufficient oxidant, hydrogen peroxide, to obtain greater than 90 percent conversion of the uranium to the uranium (VI) oxidation state to the phosphoric acid solution and simultaneously extracting the uranium (VI)

Method for the recovery of uranium from phosphoric acid, originating from the wet-process of uraniferous phosphate ores

International Nuclear Information System (INIS)

Pyrih, R.Z.; Rickard, R.S.; Carrington, O.F.

1978-01-01

Improvement in the process for recoverying uranium from wet-process phosphoric acid solution derived from the acidulation of uraniferous phosphate ores by the use of two ion exchange circuits is described. (Auth.)

40 CFR 721.6200 - Fatty acid polyamine condensate, phosphoric acid ester salts.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fatty acid polyamine condensate... New Uses for Specific Chemical Substances § 721.6200 Fatty acid polyamine condensate, phosphoric acid... substances identified as fatty acid polyamine condensate, phosphate ester salts (PMNs P-90-1984 and P-90-1985...

Recovering uranium from phosphoric acid

International Nuclear Information System (INIS)

Abodishish, H.A.; Ritchey, R.W.

1982-01-01

Precipitation of Fe 3 HN 4 H 8 (PO 4 ) 6 is prevented in the second cycle extractor, in a two cycle uranium recovery process, by washing ammonia laden organic solvent stream, from the second cycle stripper, with first cycle raffinate iron stream containing phosphoric acid, prior to passing the solvent stream into the second cycle extractor. (author)

Recovery of uranium in the production of concentrated phosphoric acid by a hemihydrate process

International Nuclear Information System (INIS)

Nakajima, S.; Miyamoto, M.

1983-01-01

Nissan Chemical Industries as manufacturers of phosphoric acid have studied the recovery of uranium, based on a concentrated phosphoric acid production process. The process consists of two stages, a hemihydrate stage with a formation of hemihydrate and a filtration section, followed by a dihydrate stage with hydration and a filtration section. In the hemihydrate stage, phosphate is treated with a mixture of phosphoric acid and sulphuric acid to produce phosphoric acid and hydrous calcium sulphate; the product is recovered in the filtration section and its concentration is 40-50% P 2 O 3 . In the dihydrate stage, the hemihydrate is transformed by re-dissolution and hydration, producing hydrous calcium sulphate, i.e. gypsum. This process therefore comprises two parts, each with different acid concentrations. As the extraction of uranium is easier in the case of a low concentration of phosphoric acid, the process consists of the recovery of uranium starting from the filtrate of the hydration section. The tests have shown that the yield of recovery of uranium was of the order of 80% disregarding the handling losses and no disadvantageous effect has been found in the combination of the process of uranium extraction with the process of concentrated phosphoric acid production. Compared with the classical process where uranium is recovered from acid with 30% P 2 O 5 , the process of producing high-concentration phosphoric acid such as the Nissan process, in which the uranium recovery is effected from acid with 15% P 2 O 5 from the hydration section, presents many advantages [fr

Some aromatic hydrazone derivatives as inhibitors for the corrosion of C-steel in phosphoric acid solution.

Science.gov (United States)

Fouda, Abd El-Aziz S; Al-Sarawy, Ahmed A; Radwan, Mohamed S

2006-01-01

The effect of furfural benzoylhydrazone and its derivatives (I-VII) as corrosion inhibitors for C-steel in 1M phosphoric acid solution has been studied by weight-loss and galvanostatic polarization techniques. A significant decrease in the corrosion rate of C-steel was observed in the presence of the investigated inhibitors. This study revealed that, the inhibition efficiency increases with increasing the inhibitor concentration, and the addition of iodide ions enhances it to a considerable extent. The effect of temperature on the inhibition efficiency of these compounds was studied using weight-loss method. Activation energy (E(a)*) and other thermodynamic parameters for the corrosion process were calculated and discussed. The galvanostatic polarization data indicated that, the inhibitors were of mixed-type, but the cathode is more polarized than the anode. The adsorption of these compounds on C-steel surface has been found to obey Frumkin's adsorption isotherm. The mechanism of inhibition was discussed in the light of the chemical structure of the undertaken inhibitors.

Determination of the activity concentration of 230Th in phosphoric acids produced in Brazil

International Nuclear Information System (INIS)

Taddei, M.H.T.; Ferreira, M.T.; Fukuma, H.T.; Xavier, T.T.; Sousa, F.V.T.S.

2017-01-01

The high uranium phosphate rock from Itataia, Brazil, was processed using the wet route in the dihydrate system to manufacture phosphoric acid. The uranium contained in phosphoric acid was recovered by the solvent extraction technique. The distribution of the long half-life radionuclides from the decay series of 238 U and 232 Th were evaluated in these processes. The 26 Ra, 228 Ra and 210 Pb radionuclides were found predominantly in phosphogypsum, while the isotopes of 228 Th, 230 Th and 232 Th predominated in phosphoric acid after extracting uranium. The main concern in the commercialization of phosphoric acid that will be produced in the Itataia plant is in relation to the content of 230 Th. This work determined the content of these radionuclides in phosphoric acid from different locations in the country in order to compare

Studies on entrained DNPPA separation by charcoal adsorption from aqueous solutions generated during uranium recovery from strong phosphoric acid

International Nuclear Information System (INIS)

Singh, D.K.; Vijayalakshmi, R.; Singh, H.

2010-01-01

During the separation of metal ions by solvent extraction technique in hydrometallurgical operations, organic solvents either get entrained or dissolved in various types of aqueous streams, which need to be separated out to prevent environmental pollution and solvent loss. Generally entrained solvents are separated on plant scale by parallel plate separators or by froth floatation cells, while the dissolved solvents are recovered either by organic diluent wash or by charcoal adsorption. A novel process has been developed to recover uranium from merchant grade phosphoric acid (MGA) employing synergistic mixture of DNPPA (di-nonyl phenyl phosphoric acid ) and TOPO (tri-n-octyl phosphine oxide) dissolved in petrofin. After recovery of uranium, MGA has to be returned to the host company for the production of fertilizer. This MGA has to be free from any contamination due to DNPPA and TOPO. Separation of DNPPA and TOPO from MGA by diluent wash method has been reported. There is no information available in literature for the separation of DNPPA and TOPO from such aqueous streams by carbon adsorption. The present investigation describes the methodology based on charcoal adsorption study (batch and continuous column operation) to separate DNPPA from MGA. Three different types of charcoal namely coconut shell based, coal based and pelletized charcoal were evaluated for DNPPA separation from MGA containing 100 mg/L DNPPA. It was found that the % DNPPA adsorptions in single contact (0.5g C/50 ml) were 57, 34 and 10 in coconut shell, coal based and pelletised charcoal respectively. Based on the results, the coconut shell based charcoal was selected for further study. Adsorption of DNPPA by coconut shell based charcoal was investigated by carrying out the experiments with 50 ml MGA containing 770 mg/L DNPPA by adding 1 to 7 g charcoal respectively in separate beakers

Radionuclide concentrations in raw and purified phosphoric acids from Brazil and their processing wastes: implications for radiation exposures.

Science.gov (United States)

da Conceição, Fabiano Tomazini; Antunes, Maria Lúcia Pereira; Durrant, Steven F

2012-02-01

Radionuclides from the U and Th natural series are present in alkaline rocks, which are used as feedstock in Brazil for the production of raw phosphoric acid, which can be considered as a NORM (naturally occurring radioactive material). As a result of the purification of raw phosphoric acid to food-grade phosphoric acid, two by-products are generated, i.e., solid and liquid wastes. Taking this into account, the main aim of this study was to evaluate the fluxes of natural radionuclide in the production of food-grade phosphoric acids in Brazil, to determine the radiological impact caused by ingestion of food-grade phosphoric acid, and to evaluate the solid waste environmental hazards caused by its application in crop soils. Radiological characterization of raw phosphoric acid, food-grade phosphoric acid, solid waste, and liquid waste was performed by alpha and gamma spectrometry. The (238)U, (234)U, (226)Ra, and (232)Th activity concentrations varied depending on the source of raw phosphoric acid. Decreasing radionuclides activity concentrations in raw phosphoric acids used by the producer of the purified phosphoric acid were observed as follows: Tapira (raw phosphoric acid D) > Catalão (raw phosphoric acids B and C) > Cajati (raw phosphoric acid A). The industrial purification process produces a reduction in radionuclide activity concentrations in food-grade phosphoric acid in relation to raw phosphoric acid produced in plant D and single raw phosphoric acid used in recent years. The most common use of food-grade phosphoric acid is in cola soft drinks, with an average consumption in Brazil of 72 l per person per year. Each liter of cola soft drink contains 0.5 ml of food-grade phosphoric acid, which gives an annual average intake of 36 ml of food-grade phosphoric acid per person. Under these conditions, radionuclide intake through consumption of food-grade phosphoric acid per year per person via cola soft drinks is not hazardous to human health in Brazil

Extraction studies on rare earths using dinonyl phenyl phosphoric acid

International Nuclear Information System (INIS)

Anitha, M.; Singh, D.K.; Kotekar, M.K.; Vijayalakshmi, R.; Singh, H.

2011-01-01

Rare earths are widely used in phosphor materials, magnetic substances, alloys, catalyst, lasers, superconductors, solid oxide fuel cells and in nuclear applications. The high value of these elements depends on their effective separation into high purity compounds. The separation into individual rare earths is very difficult to achieve, due to the very low separation factors between two adjacent rare earths arising due to similar chemical properties. Taking the advantage of variation in basicity, the separation is generally accomplished by solvent extraction or ion exchange. There are several references on the separation of rare earth in different media employing various types of extractants such as 2-ethylhexyl 2-ethyhexylphosphonic acid (EHEHPA) and di-2-ethyl hexyl phosphoric acid (D2EHPA) which have been widely used for the separation and purification of rare earths. Dinonyl phenyl phosphoric acid (DNPPA) is an organo phosphorus extractant (pKa = 2.54) and is an aromatic analogue of D2EHPA, which extracts metal ion by cation exchange mechanism. DNPPA was explored to recover rare earths from phosphate media such as wet process phosphoric acid and merchant grade acid. However, there is no information available in literature on DNPPA for RE extraction from chloride medium. Therefore, an attempt has been made in the present study to investigate the feasibility of using DNPPA for extraction of La(III), Dy(III) and Y(III) from chloride medium

Why do proton conducting polybenzimidazole phosphoric acid membranes perform well in high-temperature PEM fuel cells?

Science.gov (United States)

Melchior, Jan-Patrick; Majer, Günter; Kreuer, Klaus-Dieter

2016-12-21

Transport properties and hydration behavior of phosphoric acid/(benz)imidazole mixtures are investigated by diverse NMR techniques, thermogravimetric analysis (TGA) and conductivity measurements. The monomeric systems can serve as models for phosphoric acid/poly-benzimidazole membranes which are known for their exceptional performance in high temperature PEM fuel cells. 1 H- and 31 P-NMR data show benzimidazole acting as a strong Brønsted base with respect to neat phosphoric acid. Since benzimidazole's nitrogens are fully protonated with a low rate for proton exchange with phosphate species, proton diffusion and conduction processes must take place within the hydrogen bond network of phosphoric acid only. The proton exchange dynamics between phosphate and benzimidazole species pass through the intermediate exchange regime (with respect to NMR line separations) with exchange times being close to typical diffusion times chosen in PFG-NMR diffusion measurements (ms regime). The resulting effects, as described by the Kärger equation, are included into the evaluation of PFG-NMR data for obtaining precise proton diffusion coefficients. The highly reduced proton diffusion coefficient within the phosphoric acid part of the model systems compared to neat phosphoric acid is suggested to be the immediate consequence of proton subtraction from phosphoric acid. This reduces hydrogen bond network frustration (imbalance of the number of proton donors and acceptors) and therefore also the rate of structural proton diffusion, phosphoric acid's acidity and hygroscopicity. Reduced water uptake, shown by TGA, goes along with reduced electroosmotic water drag which is suggested to be the reason for PBI-phosphoric acid membranes performing better in fuel cells than other phosphoric-acid-containing electrolytes with higher protonic conductivity.

Process engineering challenges of uranium extraction from phosphoric acid on industrial scale

International Nuclear Information System (INIS)

Mouriya, Govind; Singh, Dhirendra; Nath, A.K.; Majumdar, D.

2014-01-01

Heavy Water Board (HWB) is a constituent unit of the Department of Atomic Energy. One of the diversified activities undertaken by HWB is pursuing exploitation of non-conventional resources for recovery of uranium from wet phosphoric acid being the most prominent one. Amongst the feasible processes for recovery of uranium from phosphoric acid is solvent extraction. Use of in-house solvent produced by HWB, is another key driver. To garner necessary information for developing the industrial scale facilities, the process has been studied in the laboratory scale, mini scale, bench scale at Heavy Water Plant, Talcher. The process was subsequently scaled up to an industrial prototype scale unit and was set up as a Technology Demonstration Plant coupled with a commercial phosphoric acid plant. The plant has successfully processed more than 2 lakh m 3 of wet phosphoric acid and all the parameters including the product, Yellow Cake have been qualified. No adverse effect has been observed in the fertilizer produced. The main characteristics of the process and subsequent process innovations are discussed in this paper. These innovations have been carried out to overcome hurdles faced during commissioning and subsequent operations of the Plant. The innovations include improved pretreatment of the wet phosphoric acid for feeding to the extraction cycle, improved control of the first cycle chemical environment, reducing the strength of the phosphoric acid used for stripping, reducing the number of equipment and machineries, alteration in solvent composition used in the first and second cycle in the solvent extraction units of the plant. (author)

Synthesis and luminescent properties of CaCO3:Eu3+@SiO2 phosphors with core-shell structure

Science.gov (United States)

Liu, Min; Kang, Ming; Chen, Kexu; Mou, Yongren; Sun, Rong

2018-03-01

Integrating the processes of preparation of CaCO3:Eu3+ and its surface-coating, core-shell structured CaCO3:Eu3+@SiO2 phosphors with red emission were synthesized by the carbonation method and surface precipitation procedure using sodium silicate as silica source. The phase structure, thermal stability, morphology and luminescent property of the as-synthesized samples were characterized by X-ray diffraction, Fourier transform infrared spectrum, thermal analysis, field-emission scanning electron microscopy, transmission electron microscope and photoluminescence spectra. The experimental results show that Eu3+ ions as the luminescence center are divided into two types: one is at the surface of the CaCO3 and the other inhabits the site of Ca2+. For CaCO3:Eu3+@SiO2 phosphors, the SiO2 layers are continuously coated on the surface of CaCO3:Eu3+ and show a typical core-shell structure. After coated with SiO2 layer, the luminous intensity and the compatibility with the rubber matrix increase greatly. Additionally, the luminous intensity increases with the increasing of Eu3+ ions concentration in CaCO3 core and concentration quenching occurs when Eu3+ ions concentration exceeds 7.0 mol%, while it is 5.0 mol% for CaCO3:Eu3+ phosphors. Therefore, preparation of CaCO3:Eu3+@SiO2 phosphors can not only simplify the experimental process through integrating the preparation of CaCO3:Eu3+ and SiO2 layer, but also effectively increase the luminous intensities of CaCO3:Eu3+ phosphors. The as-obtained phosphors may have potential applications in the fields of optical materials and functional polymer composite materials, such as plastics and rubbers.

Proton conductance at elevated temperature:Formulation and investigation of poly(4-styrenesulfonic acid / 4-aminobenzylamine / phosphoric acid membranes

Directory of Open Access Journals (Sweden)

Jalal eJalili

2014-07-01

Full Text Available 4-aminobenzylamine and phosphoric acid were blended in various proportions with poly (4-styrenesulfonic acid to form a new group of membranes exhibiting proton conductance under water-free conditions. The 4-aminobenzylamine molecule, possessing an aniline-like and benzylamine-like functional group, can interact both with the phosphoric acid and the poly(4-styrenesulfonic acid via nucleophilic interaction, thereby allowing proton jumping in the structure. Physico-chemical and thermal characteristics of the prepared solid membranes were investigated by IR spectroscopy and thermo-gravimetric analysis, respectively. Electrochemical impedance spectroscopy was employed to investigate their proton-conductance properties. Transparent composite membranes were prepared. However, the membranes are opaque for relatively high content of phosphoric acid. These membranes are thermally stable up to 300°C. The proton conductivity increases with temperature and also with content of phosphoric acid. Values as high as 1.8×10–3 S cm–1 were measured at 190°C in fully anhydrous condition.

[Removal and Recycle of Phosphor from Water Using Magnetic Core/Shell Structured Fe₃O₄ @ SiO₂Nanoparticles Functionalized with Hydrous Aluminum Oxide].

Science.gov (United States)

Lai, Li; Xie, Qiang; Fang, Wen-kan; Xing, Ming-chao; Wu, De-yi

2016-04-15

A novel magnetic core/shell structured nano-particle Fe₃O₄@ SiO₂phosphor-removal ahsorbent functionalized with hydrous aluminum oxides (Fe₃O₄@ SiO₂@ Al₂O₃· nH₂O) was synthesized. Fe₃O₄@ SiO₂@ Al₂O₃· nH₂O was characterized by XRD, TEM, VSM and BET nitrogen adsorption experiment. The XRD and TEM results demonstrated the presence of the core/shell structure, with saturated magnetization and specific surface area of 56.00 emu · g⁻¹ and 47.27 m² · g⁻¹, respectively. In batch phosphor adsorption experiment, the Langmuir adsorption maximum capacity was 12.90 mg · g⁻¹ and nearly 96% phosphor could be rapidly removed within a contact time of 40 mm. Adsorption of phosphor on Fe₃O₄@ SiO₂@ Al₂O₃ · nH₂O was highly dependent on pH condition, and the favored pH range was 5-9 in which the phosphor removal rate was above 90%. In the treatment of sewage water, the recommended dosage was 1.25 kg · t⁻¹. In 5 cycles of adsorption-regeneration-desorption experiment, over 90% of the adsorbed phosphor could be desorbed with 1 mol · L⁻¹ NaOH, and Fe₃O₄@ SiO₂@ Al₂O₃· nH₂O could be reused after regeneration by pH adjustment with slightly decreased phosphor removal rate with increasing recycling number, which proved the recyclability of Fe₃O₄@ SiO₂@ Al₂O₃· nH₂O and thereby its potential in recycling of phosphor resources.

Application of a precipitation method for uranium recovery from abu-zaabal phosphoric acid plant, Egypt

International Nuclear Information System (INIS)

El-hazek, N.M.T.; Hussein, E.M.

1995-01-01

Current industrial recovery of uranium from 30% phosphoric acid-produced by the dihydrate process-is based on solvent extraction method. Uranium recovery from concentrated phosphoric acid (45-52% p o5 ) produced by evaporation of the 30% acid or directly produced by the hemihydrate process, by solvent extraction is difficult to apply in practice. In addition to possible contamination of the acid by the organic solvents and/or their deterioration. This paper investigates the possibility of applying a precipitation method (Weterings and Janssen, 1985) for uranium recovery from both low (28% P 2 O 5 ) and high (48% P 2 O 5 ) concentration phosphoric acids produced by abu-zaabal phosphoric acid plant (Abuzaabal fertilizers and chemicals Co., Egypt). The 28% acid produced by H 2 SO 4 dihydrate method and the 48% acid produced by evaporation of the 28% acid The applied precipitation method depends on using NH 4 F as a uranium precipitant from both low and high concentration phosphoric acids in presence of acetone as a dispersing agent. All the relevant factors have been studied

Flotation of uranium values using di (2-ethyl hexyl) phosphoric acid

International Nuclear Information System (INIS)

Singh, Ajoy Kumar; Padmanabhan, N.P.H.; Sridhar, U.; Krishna Rao, N.

1998-01-01

The use of solvent extractants for mineral flotation, especially for difficult-to-float minerals, is gaining importance as they are highly selective to specific metal ions and form strong and stable complexes mostly by chelation. Studies carried out with di(2 ethyl hexyl) phosphoric acid (D2EHPA) (an organic solvent used in the extraction of uranium from phosphoric acid) as collector for flotation of uranium minerals from ore samples of Domiasiat, Meghalaya and Jaduguda, Bihar have yielded encouraging results. Although flotation of uranium minerals using other solvent extractants like tributyl phosphoric acid (TBP) has been studied, the uraninite-D2EHPA system has not been tested so far. This technical note puts on record the findings of the preliminary studies carried out. (author)

Synthesis and Characterization of SiO2@Y2MoO6:Eu3+ Core-Shell Structured Spherical Phosphors by Sol-Gel Process.

Science.gov (United States)

Li, G Z; Liu, F H; Chu, Z S; Wu, D M; Yang, L B; Li, J L; Wang, M N; Wang, Z L

2016-04-01

SiO2@Y2MoO6:Eu3+ core-shell phosphors were prepared by the sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays were used to characterize the resulting SiO2@Y2MoO6:Eu3+ core-shell phosphors. The XRD results demonstrated that the Y2MoO6:Eu3+ layers on the SiO2 spheres crystallized after being annealed at 700 °C and the crystallinity increased with raising the annealing temperature. The obtained core-shell phosphors have spherical shape with narrow size distribution (average size ca. 640 nm), non-agglomeration, and smooth surface. The thickness of the Y2MoO6:Eu3+ shells on the SiO2 cores could be easily tailored by varying the number of deposition cycles (70 nm for four deposition cycles). The Eul+ shows a strong PL emission (dominated by 5D0-7F2 red emission at 614 nm) under the excitation of 347 nm UV light. The PL intensity of Eu3+ increases with increasing the annealing temperature and the number of coating cycles.

Natural Radiation in byproducts of the production of phosphoric acid

International Nuclear Information System (INIS)

Silveira, Marcilei A. Guazzelli da; Cardoso, L.L.; Medina, N.H.

2014-01-01

Natural radiation is the largest source of radiation exposure to which man is subject. It is formed basically by cosmic radiation and the radionuclides present in the Earth crust, as 40 K and the elements of the decay series of 232 Th and 238 U. Phosphate ores, which constitutes the raw material for the production of phosphoric acid, have a high rate of natural radiation from the decay series of 232 Th and 238 U. Phosphogypsum, which is naturally radioactivity, is a by-product of the production of phosphoric acid by the wet method. For each ton of phosphoric acid it is produced about 4.5 tons of phosphogypsum. This work presents the analysis of samples collected in all stages of the manufacturing process of phosphoric acid, which generates the phosphogypsum. Gamma-ray spectrometry was used to measure the concentration of the elements of the decay series of 232 Th and 238 U. All analyzed samples showed a high concentration of radionuclides, promoting the need for further steps in the process in order to reduce the presence of such radionuclides in the phosphogypsum. The results indicate the radionuclide 238 U has higher contribution in some samples of the intermediate stages of the process. All samples exceeded the international average range of human exposure to terrestrial gamma radiation, which is 0.3 to 1.0 mSv/year. (author)

Application of a precipitation method for uranium recovery from Abu-Zaabal phosphoric acid plant, egypt

International Nuclear Information System (INIS)

El-Hazek, N.M.T.; Hussein, E.M.

1997-01-01

Current industrial recovery of uranium from 30% phosphoric acid-produced by the dihydrate process-is based on solvent extraction method. Uranium recovery from concentrated phosphoric acid (45-52% P 2 O 5 ) produced by evaporation of the 30% acid or directly produced by the hemihydrate process, by solvent extraction is difficult to apply in practice. In addition to possible contamination of the acid by the organic solvents and/or their deterioration. This paper investigates the possibility of applying a precipitation method (Weterings and Janssen, 1985) for uranium recovery from both low (28% P 2 O 2 ) and high (48% P 2 O 5 ) concentration phosphoric acids produced by abu-Zaabal phosphoric acid plant (abu-Zaabal fertilizers and chemicals Co., Egypt). The 28% acid produced by H 2 SO 4 dihydrate method and the 48% acid produced by evaporation of the 28% acid

Solid phosphoric acid oligomerisation: Manipulating diesel selectivity by controlling catalyst hydration

International Nuclear Information System (INIS)

Prinsloo, Nicolaas M.

2006-01-01

Solid phosphoric acid (SPA) catalyst is traditionally used in crude oil refineries to produce unhydrogenated motor-gasoline by propene and butene oligomerisation. SPA is also used in High-Temperature Fischer-Tropsch refineries (HTFT) to produce synthetic fuels albeit with a different emphasis. The petrol/diesel ratio of an HTFT refinery is very different from crude refining and it is often necessary to shift this ratio depending on market requirements. The influence of hydration was investigated as a means of improving diesel selectivity. This was achieved by studying SPA over a hydration range of 99-110% H 3 PO 4 , a temperature range of 140-230 o C and using C 3 -C 6 model and synthetic FT-derived olefinic feedstocks. A direct correlation was found between the selectivity towards diesel range products and the distribution of the phosphoric acid species viz. H 3 PO 4 , H 4 P 2 O 7 and H 5 P 3 O 10 . For various olefinic feedstocks, diesel selectivity increased with decreasing catalyst hydration with a maximum around 108% H 3 PO 4 for propene oligomerisation. Commercial tests confirmed the increase in diesel selectivity with lowered catalyst hydration. (author)

Inorganic-Organic hybrid materials for uranium extraction from phosphoric acid

International Nuclear Information System (INIS)

El-Mourabit, Sabah

2013-01-01

Phosphate rocks are industrially processed in large quantities to produce phosphoric acid and fertilisers. These rocks contain significant concentration of uranium (50 to 300 ppm) which could be interesting for nuclear industry. This work deals with the valorisation of uranium as a by-product from fertiliser industry. The aim of this study is to develop a hybrid material, constituted of an inorganic solid support grafted with an extractant (complexing molecule), which can extract selectively uranium from phosphoric acid medium. The first step of our approach was to identify an inorganic support which is stable under these particular conditions (strong acidity and complexing medium). The chemical and mechanical stability of different meso-porous materials, such as silica, glass and carbon was studied. In a second phase, we focused on the identification and the optimisation of complexing molecules, specific of uranium in phosphoric acid. These ligands were then grafted on the most stable solids. Finally, the efficiency of these hybrid systems was evaluated through different tests of extraction, selectivity and de-extraction. (author) [fr

Influence of pH-control in phosphoric acid treatment of zinc oxide

Energy Technology Data Exchange (ETDEWEB)

Onoda, H., E-mail: onoda@kpu.ac.jp [Department of Informatics and Environmental Sciences, Kyoto Prefectural University (Japan); Chemel, M. [Ecole de Biologie Industrielle, CERGY Cedex (France)

2017-04-15

Zinc oxide is often used as a white pigment for cosmetics; however, it shows photocatalytic activity that causes decomposition of sebum on the skin when exposed to the ultraviolet radiation in sunlight. In this work, zinc oxide was reacted with phosphoric acid at various pH values to synthesize a novel white pigment for cosmetics. The chemical composition, powder properties, photocatalytic activities, colors, and smoothness of these pigments were studied. The obtained materials exhibited X-ray diffraction peaks relating to zinc oxide and phosphate after phosphoric acid treatment. The ratio of zinc phosphate to zinc oxide was estimated from inductively coupled plasma - atomic emission spectroscopy results. Samples treated at pH 4-7 yielded small particles with sub-micrometer sizes. The photocatalytic activity of zinc oxide became lower after phosphoric acid treatment. Samples treated at pH 4-7 showed the same reflectance as zinc oxide in both the ultraviolet and visible ranges. Adjustment of the pH was found to be important in the phosphoric acid treatment of zinc oxide. (author)

Reactivity of the cadmium ion in concentrated phosphoric acid solutions.

Science.gov (United States)

De Gyves, J; Gonzales, J; Louis, C; Bessiere, J

1989-07-01

The solvation transfer coefficients which characterize the changes of ion reactivity with phosphoric acid concentration have been calculated for cadmium from the constants of the successive chloride complexes, and for silver and diethyldithiophosphate from potentiometric measurements. They evidence the strong desolvation of the cadmium species in concentrated phosphoric acid media, causing a remarkable increase of its reactivity. They allow the results of liquid-liquid extraction, precipitation and flotation reactions to be correctly interpreted and their changes to be foreseen when the reagents are modified.

Pretreatment of phosphoric acid of Annaba

International Nuclear Information System (INIS)

Kada, R.

1990-03-01

The most important step in the process of uranium recovery from phosphoric acid is the pretreatment operation. In this study, the adsorption of organic matters on activated carbon was carried out in a batch process and in a fixed bed column. First, the chemical and physical characterization of phosphoric acid, activated carbon and gypsum were performed. In addition, the organic matters were qualitatively analysed and a new and original quantitative method was experimented. Next, the various operating parameters such as agitation speed, granulometry, temperature, solid/liquid ratio, initial concentration, acid flowrate, and bed height were optimized. The experimental equilibrium isotherm was compared to the Langmuir, Freundlich, and Redlich-Peterson theoretical isotherms. It was noticed that the three models did not fit the experimental isotherm in the total concentration range. Thus, an original bilinear model was proposed. The influence of the operating conditions on the adsorption kinetics was also investigated. As a result of that, a new mathematical model was proposed to determine both the liquid and solid phases mass transfer and the solid phase diffusion coefficient. Finally, adsorption of organic matters on a fixed bed process allowed computation of the number of transfer units (NTU), the height of adsorption zone and the degree of saturation of activated carbon

The preparation of 32P labelled phosphorous acid

International Nuclear Information System (INIS)

Henderson, D.; Jenkinson, A.; Sorby, P.

1986-11-01

Phosphorous acid labelled with 32 P has been prepared, on a small scale, starting from neutron-irradiated phosphorus. The compound is intended for tracer studies in the development of novel fungicides

Method for recovery of uranium from phosphoric acid

International Nuclear Information System (INIS)

Duarte Neto, J.

1984-01-01

The results of a method for recuperation of uranium from phosphoric acid by humid way are presented. The extracting mixture used was di-ethylhexylphosphoric acid (D 2 EHPA) and trioctylphosphine oxide (TOPO). An installation in micro-pilot scale was made to get and visualize data for continuous process. (M.A.C.) [pt

Extraction of uranium from phosphoric-hydrobromic acid mixture by N-lauryl tri alkyl methylamine

Energy Technology Data Exchange (ETDEWEB)

Guirguis, L A [Nuclear materials authority, Cairo, (Egypt); Tadros, N A [Hot laboratories center, atomic energy authority, Cairo, (Egypt)

1995-10-01

A uranium recovery process from phosphoric acid produced by the dihydrate method was elaborated. Decomposition of phosphate rock containing 0.02% U is carried out with sulphuric acid. Crude phosphoric acid is filtered off, steam concentrated to 45% P{sub 2} O{sub 5} (6.27 M) and then clarified with activated clay and carbon. The clear phosphoric acid is introduced to uranium extraction after the addition of 0.88 M hydrobromic acid by 0.134 M amberlite LA.2 and 5% decanol, as a modifier, in kerosene. While 10% ammonium sulphate solution is used for stripping. Over 90% uranium recovery is obtained. 6 figs., 1 tab.

Rare earth elements recycling from waste phosphor by dual hydrochloric acid dissolution

International Nuclear Information System (INIS)

Liu, Hu; Zhang, Shengen; Pan, Dean; Tian, Jianjun; Yang, Min; Wu, Maolin; Volinsky, Alex A.

2014-01-01

Highlights: • The article provides a new method for recycling rare earth (RE) from waste phosphor. • When compared with the traditional methods, leach rate was much higher. • Y–Eu concentrate and Tb–Ce concentrate were obtained successively. • It would reduce the burden of later extraction, separation and purification. - Abstract: This paper is a comparative study of recycling rare earth elements from waste phosphor, which focuses on the leaching rate and the technical principle. The traditional and dual dissolution by hydrochloric acid (DHA) methods were compared. The method of dual dissolution by hydrochloric acid has been developed. The Red rare earth phosphor (Y 0.95 Eu 0.05 ) 2 O 3 in waste phosphor is dissolved during the first step of acid leaching, while the Green phosphor (Ce 0.67 Tb 0.33 MgAl 11 O 19 ) and the Blue phosphor (Ba 0.9 Eu 0.1 MgAl 10 O 17 ) mixed with caustic soda are obtained by alkali sintering. The excess caustic soda and NaAlO 2 are removed by washing. The insoluble matter is leached by the hydrochloric acid, followed by solvent extraction and precipitation (the DHA method). In comparison, the total leaching rate of the rare earth elements was 94.6% by DHA, which is much higher than 42.08% achieved by the traditional method. The leaching rate of Y, Eu, Ce and Tb reached 94.6%, 99.05%, 71.45%, and 76.22%, respectively. DHA can decrease the consumption of chemicals and energy. The suggested DHA method is feasible for industrial applications

Complexity in Acid?Base Titrations: Multimer Formation Between Phosphoric Acids and Imines

OpenAIRE

Malm, Christian; Kim, Heejae; Wagner, Manfred; Hunger, Johannes

2017-01-01

Abstract Solutions of Br?nsted acids with bases in aprotic solvents are not only common model systems to study the fundamentals of proton transfer pathways but are also highly relevant to Br?nsted acid catalysis. Despite their importance the light nature of the proton makes characterization of acid?base aggregates challenging. Here, we track such acid?base interactions over a broad range of relative compositions between diphenyl phosphoric acid and the base quinaldine in dichloromethane, by u...

Kinetic study of ion exchange in phosphoric acid chelating resin

International Nuclear Information System (INIS)

Brikci-Nigassa, Mounir; Hamouche, Hafida

1995-11-01

Uranium may be recovered as a by product of wet phosphoric acid using a method based on specific ion exchange resins. These resins called chelates contain amino-phosphonic functional groups. The resin studied in this work is a purolite S-940; uranium may be loaded on this resin from 30% P2O5 phosphoric acid in its reduced state. The influence of different parameters on the successive steps of the process have been studied in batch experiments: uranium reduction, loading and oxydation. Uranium may be eluted with ammonium carbonate and the resin regeneration may be done with hydrochloric acid.Ferric ions reduce the effective resin capacity considerably and inert fixation conditions are proposed to enhance uranium loading

Process for the winning of a concentrate containing uranium and purified phosphoric acid, as well as the concentrate containing uranium and purified phosphoric acid obtained by this process

International Nuclear Information System (INIS)

1980-01-01

The uranium containing concentrate and purified phosphoric acid are obtained by treating wet phosphoric acid with an inorganic fluorine compound (ammonium fluoride) and an aliphatic ketone (acetone) in the presence of a reducing agent (finely divided iron). The ketone is added first and the formed uranium precipitate is separated from the solution. If the fluorine compound is added first, the yield is lowered by a factor of 2. (Th.P.)

Semitechnical studies of uranium recovery from wet process phosphoric acid by liquid-liquid-extraction method

International Nuclear Information System (INIS)

Poczynajlo, A.; Wlodarski, R.; Giers, M.

1987-01-01

A semitechnical installation for uranium recovery from wet process phosphoric acid has been built. The installation is based on technological process comprising 2 extraction cycles, the first with a mixture of mono- and dinonylphenylphosphoric acids (NPPA) and the second with a synergic mixture of di-/2-ethylhexyl/-phosphoric acid (D2EHPA) and trioctylphosphine oxide (TOPO). The installation was set going and the studies on the concentration distributions of uranium and other components of phosphoric acid have been performed for all technological circuits. 23 refs., 15 figs., 3 tabs. (author)

Effect of acetic acid on wet patterning of copper/molybdenum thin films in phosphoric acid solution

International Nuclear Information System (INIS)

Seo, Bo.-Hyun; Lee, Sang-Hyuk; Park, In-Sun; Seo, Jong Hyun; Choe, HeeHwan; Jeon, Jae-Hong; Hong, Munpyo; Lee, Yong Uk; Winkler, Joerg

2011-01-01

Copper metallization is a key issue for high performance thin film transistor (TFT) technology. A phosphoric acid based copper etchant is a potentially attractive alternative to the conventional hydrogen peroxide based etchant due to its longer-life expectancy time and higher stability in use. In this paper, it is shown that amount of the acetic acid in the phosphoric based copper etchant plays an important role in controlling the galvanic reaction between the copper and the molybdenum. As the concentration of acetic acid in the phosphoric mixture solution increased from 0 M to 0.4 M, the measured galvanic current density dropped from 32 mA/cm 2 to 26 mA/cm 2 , indicating that the acetic acid induces the lower galvanic reaction between the copper and the molybdenum in the solution. From the XPS analysis, with the addition of the acetic acid, the thickness of the protective MoO 2 passive film covering the molybdenum surface grew and the dissolution rate of the molybdenum thin film decreased. However, the dissolution rate of the copper thin film increased as the concentration of acetic acid in the mixture solution increased.

Effect of acetic acid on wet patterning of copper/molybdenum thin films in phosphoric acid solution

Energy Technology Data Exchange (ETDEWEB)

Seo, Bo.-Hyun; Lee, Sang-Hyuk; Park, In-Sun [Department of Materials Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Seo, Jong Hyun, E-mail: jhseo@kau.ac.kr [Department of Materials Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Choe, HeeHwan; Jeon, Jae-Hong [School of Electronics, Telecommunications and Computer Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Hong, Munpyo [Display and Semiconductor Physics, Korea University (Korea, Republic of); Lee, Yong Uk [PETEC (The Printable Electronics Technology Centre) (United Kingdom); Winkler, Joerg [PLANSEE Metal GmbH, Metallwerk-Plansee-Str. 71A-6600, Reutte (Austria)

2011-08-01

Copper metallization is a key issue for high performance thin film transistor (TFT) technology. A phosphoric acid based copper etchant is a potentially attractive alternative to the conventional hydrogen peroxide based etchant due to its longer-life expectancy time and higher stability in use. In this paper, it is shown that amount of the acetic acid in the phosphoric based copper etchant plays an important role in controlling the galvanic reaction between the copper and the molybdenum. As the concentration of acetic acid in the phosphoric mixture solution increased from 0 M to 0.4 M, the measured galvanic current density dropped from 32 mA/cm{sup 2} to 26 mA/cm{sup 2}, indicating that the acetic acid induces the lower galvanic reaction between the copper and the molybdenum in the solution. From the XPS analysis, with the addition of the acetic acid, the thickness of the protective MoO{sub 2} passive film covering the molybdenum surface grew and the dissolution rate of the molybdenum thin film decreased. However, the dissolution rate of the copper thin film increased as the concentration of acetic acid in the mixture solution increased.

Rare earth elements recycling from waste phosphor by dual hydrochloric acid dissolution

Energy Technology Data Exchange (ETDEWEB)

Liu, Hu [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Zhang, Shengen, E-mail: zhangshengen@mater.ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Pan, Dean; Tian, Jianjun; Yang, Min; Wu, Maolin [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Volinsky, Alex A. [Department of Mechanical Engineering, University of South Florida, Tampa, FL 33620 (United States)

2014-05-01

Highlights: • The article provides a new method for recycling rare earth (RE) from waste phosphor. • When compared with the traditional methods, leach rate was much higher. • Y–Eu concentrate and Tb–Ce concentrate were obtained successively. • It would reduce the burden of later extraction, separation and purification. - Abstract: This paper is a comparative study of recycling rare earth elements from waste phosphor, which focuses on the leaching rate and the technical principle. The traditional and dual dissolution by hydrochloric acid (DHA) methods were compared. The method of dual dissolution by hydrochloric acid has been developed. The Red rare earth phosphor (Y{sub 0.95}Eu{sub 0.05}){sub 2}O{sub 3} in waste phosphor is dissolved during the first step of acid leaching, while the Green phosphor (Ce{sub 0.67}Tb{sub 0.33}MgAl{sub 11}O{sub 19}) and the Blue phosphor (Ba{sub 0.9}Eu{sub 0.1}MgAl{sub 10}O{sub 17}) mixed with caustic soda are obtained by alkali sintering. The excess caustic soda and NaAlO{sub 2} are removed by washing. The insoluble matter is leached by the hydrochloric acid, followed by solvent extraction and precipitation (the DHA method). In comparison, the total leaching rate of the rare earth elements was 94.6% by DHA, which is much higher than 42.08% achieved by the traditional method. The leaching rate of Y, Eu, Ce and Tb reached 94.6%, 99.05%, 71.45%, and 76.22%, respectively. DHA can decrease the consumption of chemicals and energy. The suggested DHA method is feasible for industrial applications.

Complexity in Acid-Base Titrations: Multimer Formation Between Phosphoric Acids and Imines.

Science.gov (United States)

Malm, Christian; Kim, Heejae; Wagner, Manfred; Hunger, Johannes

2017-08-10

Solutions of Brønsted acids with bases in aprotic solvents are not only common model systems to study the fundamentals of proton transfer pathways but are also highly relevant to Brønsted acid catalysis. Despite their importance the light nature of the proton makes characterization of acid-base aggregates challenging. Here, we track such acid-base interactions over a broad range of relative compositions between diphenyl phosphoric acid and the base quinaldine in dichloromethane, by using a combination of dielectric relaxation and NMR spectroscopy. In contrast to what one would expect for an acid-base titration, we find strong deviations from quantitative proton transfer from the acid to the base. Even for an excess of the base, multimers consisting of one base and at least two acid molecules are formed, in addition to the occurrence of proton transfer from the acid to the base and simultaneous formation of ion pairs. For equimolar mixtures such multimers constitute about one third of all intermolecular aggregates. Quantitative analysis of our results shows that the acid-base association constant is only around six times larger than that for the acid binding to an acid-base dimer, that is, to an already protonated base. Our findings have implications for the interpretation of previous studies of reactive intermediates in organocatalysis and provide a rationale for previously observed nonlinear effects in phosphoric acid catalysis. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Continuous tests of Phosphoric Acid - dihydrate process - from phosphatic concentrate of Itataia-CE ore

International Nuclear Information System (INIS)

Santos Benedetto, J. dos.

1984-01-01

A consolidation of principal studies and continuous tests done with phosphatic concentrated of Itataia ore intending phosphoric acid production by humid-route dihydrate way process is presented. The production of phosphoric acid is applied in uranium extraction process by solvents. (author) [pt

Oxidizer in phosphoric reactors

International Nuclear Information System (INIS)

Santos Benedetto, J. dos

1985-01-01

Oxidation during the manufacture of wet-process phosphoric acid affected the distribution of uranium and impurities between phosphoric acid and gypsum, by decreasing the uranium loss to gypsum and the impurities solubilization in phosphoric acid. (Author) [pt

Performance of phosphoric acid activated montmorillonite as buffer materials for radioactive waste repository

International Nuclear Information System (INIS)

Wang, Tsing-Hai; Liu, Tsung-Ying; Wu, Ding-Chiang; Li, Ming-Hsu; Chen, Jiann-Ruey; Teng, Shi-Ping

2010-01-01

In this study, the performance of phosphoric acid activated montmorillonite (PAmmt) was evaluated by cesium ions adsorption experiments. The PAmmt samples were obtained by activating with 1, 3 and 5 mol L -1 of phosphoric acid, respectively under reflux for 3, 12, and 24 h. Experimental results demonstrated that the treatment of raw K-10 montmorillonite with phosphoric acid increased the materials' affinity for Cs uptake and no significant amount of suspension solids were produced. A relatively insignificant variation in the CEC value was observed. Furthermore, PAmmt also showed high adsorption selectivity toward Cs ions. The improved sorptive properties were mainly related to the increased surface area and the relatively higher surface charge density. Increased specific surface area was the resulted from partial decomposition of lamellar structure of mmt; while the higher surface charge density was caused by the protonation of octahedral Al-OH sites during the acid activation. Generally speaking, stronger acid concentration and longer activation times would produce relatively more decomposed PAmmt particles. However, as the activation exceeds 3 h, the precipitation of Si 4+ would passivate PAmmt against further acid attacks. Based upon our results, acid activation by phosphoric acid could produce PAmmt samples with high sorption capacity and selectivity, and good structural integrity, which are beneficial to be used at radioactive waste repository.

Phosphoric acid fuel cell R and D activities at KACST

International Nuclear Information System (INIS)

Ghouse, M.; Aba-Oud, H.; Ba-Junaid, M.; Al-Garni, M.; Quadri, M.I.

1993-01-01

The PAFC (Phosphoric Acid Fuel Cell) activities are directed towards the development of components of single cell and experimental stacks at KACST. The main aim of the present task is to design and construct a 1 kW PAFC Stack and demonstrate it by integrating with an electrolyser using a DC current generated by a photovoltaic power source. This paper describes the preparation of porous teflon bonded gas diffusion carbon electrodes and their evaluation as single phosphoric acid fuel cells using hydrogen as a fuel and oxygen/air as an oxidant. 6 figs., 2 tabs., 15 refs

Properties of precipitates formed during ammonization of extractional phosphoric acid

International Nuclear Information System (INIS)

Zakharova, B.S.; Komissarova, L.N.; Naumov, S.V.; Traskin, V.Yu.

1992-01-01

Dimensions of precipitated rare-earth phosphate particles -(0.1 μm)- are near the boundary of colloidal system sedimentation stability range at neutralization of extraction phosphoric acid. Thus, formation of multiple aggregates of colloidal particles results in immediate sedimentation of the precipitate. Processes occurring within the system may be described using second order reaction equation. Average efficient size of precipitates grows at reduction of reaction mixture pH. About 30% of rare-earth elements and yttrium in the extraction phosphoric acid is extracted from it; concentration of rare-earth elements, yttrium and scandium in precipitate is maximum 2 mass. %

Uranium recovery from the concentrated phosphoric acid prepared by the hemi-hydrate process

Energy Technology Data Exchange (ETDEWEB)

Fouad, E A; Mahdy, M A; Bakr, M Y [Nuclear materials authority, Cairo, (Egypt); Zatout, A A [Faculty of engineering, Alex. university, Alex, (Egypt)

1995-10-01

It has been proved that the uranium dissolution from El-sebaiya phosphate ore was possible by using 10 Kg of K Cl O{sub 4}/ ton rock during the preparation of high strength phosphoric acid using the hemi hydrate process. In the present work, effective extraction of uranium (about 90%) from the high strength phosphoric acid using a new synergistic solvent mixture of 0.75 M D 2 EHPA/0.1 M TOHPO had been a success. Stripping of uranium from the organic phase was possible by 10 M phosphoric acid while the direct precipitation of uranium concentrate from the later was feasible by using N H{sub 4} F in presence of acetone. 8 figs.

Uranium recovery from the concentrated phosphoric acid prepared by the hemi-hydrate process

International Nuclear Information System (INIS)

Fouad, E.A.; Mahdy, M.A.; Bakr, M.Y.; Zatout, A.A.

1995-01-01

It has been proved that the uranium dissolution from El-sebaiya phosphate ore was possible by using 10 Kg of K Cl O 4 / ton rock during the preparation of high strength phosphoric acid using the hemi hydrate process. In the present work, effective extraction of uranium (about 90%) from the high strength phosphoric acid using a new synergistic solvent mixture of 0.75 M D 2 EHPA/0.1 M TOHPO had been a success. Stripping of uranium from the organic phase was possible by 10 M phosphoric acid while the direct precipitation of uranium concentrate from the later was feasible by using N H 4 F in presence of acetone. 8 figs

Developing a rapid method for the determination of uranium in pure phosphoric acid and D2 EHPA

International Nuclear Information System (INIS)

Koudsi, Y.; Stas, J.; Al-Merey, R.; shaddoud, G.

1996-02-01

Arsenazo (III) used in titrate uranium spectrophotometrically in phosphoric acid after its extraction into organic phase. In this work we used arsenazo(III) to complex uranyl ion in pure phosphoric acid and in the aqueous phase. The spectrum of the complex shows that λ max is at 650 nm. The linearity of the method is corelated with acid molarity, it is (1 -4, 10 - 30, 10 - 40) ppm uranium for (0.2, 1, 2) M of phosphoric acid respectively. Uranium in D 2 EHPA stripped by phosphoric acid and then determined by this method. Also it has been applied to determine uranium in pure perchloric acid. The method is direct, rapid, very cheap and relatively accurate. (author)

Determination of vanadium in Syrian commercial and raffinate phosphoric acid

International Nuclear Information System (INIS)

Al-Merey, R.

2002-04-01

This study presents two methods for vanadium determination in Syrian commercial phosphoric acid. The vanadium (V) in the oxidized commercial phosphoric acid by ammonium persulfate solution is extracted from 5-M hydrochloride acid medium using N-benzoyl-N-phenyl hydroxyl amine (BPHA) in chloroform as an extracting solution. The first method, the extract vanadium as VOL 2 Cl is changed to V 2 O 3 L 4 complex by the addition of benzimidazole in 1-butanol to the violet organic layer. The absorbance is then measured at 440 nm (the molar absorptivity was found to be 3865 M -1 cm -1 ), where Beer law is applicable up to 36-μg ml -1 . the accuracy, precision and detection limit were found to be 3.7%, 77 ppb and 37 ppb, respectively. the second method, the organic layer is heated to evaporate chloroform, the residue is digested using 20% ammonium persulfate and 2-M sulfuric acid solutions. The vanadium concentration is measured spectrophotometrically by oxidizing gallic acid with persulfate (S 2 O 8 2- ) anion in phosphoric acid medium, where the vanadium (V) acts as a catalyst in the oxidation reaction. This method has a high sensitivity (∼10 -12 ) with accuracy and precision 5% and 0.621 ppb, respectively. Also Beer law at λ m ax=415 nm (ε=∼2 x 10 6 M -1 ) is applicable in the range 2.58-33.3 ppb. (author)

Amino-Functional Polybenzimidazole Blends with Enhanced Phosphoric Acid Mediated Proton Conductivity as Fuel Cell Electrolytes

DEFF Research Database (Denmark)

Aili, David; Javakhishvili, Irakli; Han, Junyoung

2016-01-01

A new amino-functional polybenzimidazole copolymer is synthesized by homogeneous solution condensation polymerization from a novel monomer, N,N′-bis (2,4-diaminophenyl)-1,3-diaminopropane. The copolymer readily dissolves in organic solvents and shows good film forming characteristics. To balance...... the phosphoric acid uptake and to obtain mechanically robust membranes, the amino-functional polybenzimidazole derivative is blended with high molecular weight poly [2,2′-(m-phenylene)-5,5′-bisbenzimidazole] at different ratios. Due to the high acid uptake, the homogenous blend membranes show enhanced proton...

Development of an improved two-cycle process for recovering uranium from wet-process phosphoric acid

International Nuclear Information System (INIS)

Chen, H.M.; Chen, H.J.; Tsai, Y.M.; Lee, T.W.; Ting, G.

1987-01-01

An improved two-cycle separation process for the recovery of uranium from wet-process phosphoric acid by extraction with bis(2-ethylhexyl)phosphoric acid (D2EHPA) plus dibutyl butylphosphonate (DBBP) in kerosene has been developed and demonstrated successfully in bench-scale, continuous mixer-settler tests. The sulfuric acid and water scrubbing steps for the recycled extraction in the second cycle solve the problems of the contamination and dilution of the phosphoric acid by the ammonium ion and water and also avoid the formation of undesirable phosphatic precipitates during the subsequent extraction of uranium by recycled organic extractant

Nitric-phosphoric acid oxidation of organic waste materials

International Nuclear Information System (INIS)

Pierce, R.A.; Smith, J.R.

1995-01-01

A wet chemical oxidation technology has been developed to address issues facing defense-related facilities, private industry, and small-volume generators such as university and medical laboratories. Initially tested to destroy and decontaminate a heterogenous mixture of radioactive-contaminated solid waste, the technology can also remediate other hazardous waste forms. The process, unique to Savannah River, offers a valuable alternative to incineration and other high-temperature or high-pressure oxidation processes. The process uses nitric acid in phosphoric acid; phosphoric acid allows nitric acid to be retained in solution well above its normal boiling point. The reaction converts organics to carbon dioxide and water, and generates NO x vapors which can be recycled using air and water. Oxidation is complete in one to three hours. In previous studies, many organic compounds were completely oxidized, within experimental error, at atmospheric pressure below 180 degrees C; more stable compounds were decomposed at 200 degrees C and 170 kPa. Recent studies have evaluated processing parameters and potential throughputs for three primary compounds: EDTA, polyethylene, and cellulose. The study of polyvinylchloride oxidation is incomplete at this time

Determination of anions in pure and commercial phosphoric acid by ion chromatography and manual of 792 basic IC

International Nuclear Information System (INIS)

Al-Kabani, F.; Abdulbaki, M. K.

2007-01-01

A method for determination of anions in pure and concentrated phosphoric and samples (85%) and commercial phosphoric acid ion chromatography was developed, in order to control the specification of phosphoric acid produced in the pilot plant for phosphoric acid purification. The accuracy of the method was studied and the standard deviation was found to be between 0.09 and 0.10. Operation instructions of 792 Basic IC was described. (author)

Process for extracting uranium from phosphoric acid solutions

International Nuclear Information System (INIS)

1977-01-01

The description is given of a method for extracting uranium from phosphoric acid solutions whereby the previously oxided acid is treated with an organic solvent constituted by a mixture of dialkylphosphoric acid and trialkylphosphine oxide in solution in a non-reactive inert solvent so as to obtain de-uraniated phosphoric acid and an organic extract constituted by the solvent containing most of the uranium. The uranium is then separated from the extract as uranyl ammonium tricarbonate by reaction with ammonia and ammonium carbonate and the extract de-uraniated at the extraction stage is recycled. The extract is treated in a re-extraction apparatus comprising not less than two stages. The extract to be treated is injected at the top of the first stage. At the bottom of the first stage, ammonia is introduced counter current as gas or as an aqueous solution whilst controlling the pH of the first stage so as to keep it to 8.0 or 8.5 and at the bottom of the last stage an ammonium carbonate aqueous solution is injected in a quantity representing 50 to 80% of the stoichiometric quantity required to neutralize the dialkylphosphoric acid contained in the solvent and transform the uranium into uranyl ammonium tricarbonate [fr

Doping phosphoric acid in polybenzimidazole membranes for high temperature proton exchange membrane fuel cells

DEFF Research Database (Denmark)

He, Ronghuan; Li, Qingfeng; Jensen, Jens Oluf

2007-01-01

Polybenzimidazole (PBI) membranes were doped in phosphoric acid solutions of different concentrations at room temperature. The doping chemistry was studied using the Scatchard method. The energy distribution of the acid complexation in polymer membranes is heterogeneous, that is, there are two...... different types of sites in PBI for the acid doping. The protonation constants of PBI by phosphoric acid are found to be 12.7 L mol(-1) (K-1) for acid complexing sites with higher affinity, and 0.19 L mol(-1) (K-2) for the sites with lower affinity. The dissociation constants for the complexing acid onto...... these two types of PBI sites are found to be 5.4 X 10(-4) and 3.6 X 10(-2), respectively, that is, about 10 times smaller than that of aqueous phosphoric acid in the first case but 5 times higher in the second. The proton conducting mechanism is also discussed....

Contribution to the study of dialcoylphosphates. The dibenzyl-phosphoric acid and its application to liquid-liquid extraction

International Nuclear Information System (INIS)

Courtemanche, Pierre V.

1966-01-01

This research thesis is a contribution to the knowledge of organophosphate compounds, and more particularly dialcoylphosphates, and even more particularly the dibenzyl-phosphoric acid or dibenzyl-phosphate (HDBzP). In a first part, the author reports studies on the synthesis of this compound by solving the specific analytic problem raised by simple organophosphates regarding their separation and identification. He also reports the study of some specific metallic derived compounds. The second part addresses the study of a specific feature of dialcoylphosphates: their interesting power of extraction with respect to metallic cations. The author shows that, through specific operational conditions (solvent nature, concentration of the extraction agent, composition of the aqueous phase containing the metallic ion), it is even possible to obtain a selective extraction. Thus, the author reports a physical-chemical study of the extraction agent, the dibenzyl-phosphoric acid

Synthesis of novel acid electrolytes for phosphoric acid fuel cells

Science.gov (United States)

Adcock, James L.

1988-11-01

A 40 millimole per hour scale aerosol direct fluorination reactor was constructed. F-Methyl F-4-methoxybutanoate and F-4-methoxybutanoyl fluoride were synthesized by aerosol direct fluorination of methyl 4-methoxybutanoate. Basic hydrolysis of the perfluorinated derivatives produce sodium F-4 methoxybutanoate which was pyrolyzed to F-3-methoxy-1-propene. Purification and shipment of 33 grams of F-3-methoxy-1-propene followed. Syntheses by analogous methods allowed production and shipment of 5 grams of F-3-ethoxy 1-propene, 18 grams of F-3-(2-methoxy.ethoxy) 1-propene, and 37 grams of F-3,3-dimethyl 1-butene. Eighteen grams of F-2,2-dimethyl 1-chloropropane was produced directly and shipped. As suggested by other contractors, 5 grams of F-3-methoxy 1-iodopropane, and 5 grams of F-3-(2-methoxy.ethoxy) 1-iodopropane were produced by converting the respective precursor acid sodium salts produced for olefin synthesis to the silver salts and pyrolyzing them with iodine. Each of these compounds was prepared for the first time by the aerosol fluorination process during the course of the contract. These samples were provided to other Gas Research Institute (GRI) contractors for synthesis of perfluorinated sulfur (VI) and phosphorous (V) acids.

Ionic flotation of uranium contained in industrial phosphoric acid

International Nuclear Information System (INIS)

Jdid; Blazy; Bessiere

1983-01-01

A new process for uranium recovery from industrial phosphoric acid at 30% of P 2 O 5 is applied by the ionic flotation process. Research is carried out on determination of the nature of ionic species of U in H 3 PO 4 5.5 M and the behavior of reagents from CECA Co. in very acid media. Reagents able to form complexes directly with uranium and stable in phosphoric acid selected are: potassium ethylene diamine tetra (methylene phosphonate) (INIPOL AD32) and sodium dialkyldiphosphonate (34S). Uranium IV, obtained by reduction of uranium VI with iron powder, is precipitated by these reagents. Flotation of the precipitate obtained with INIPOL AD 32 is realized by addition of hexylamino bis (methylene phosphonic acid). A recovery of 80 wt% is obtained. Flotation of the coprecipitate 34S-U(IV) is obtained without any other additions because 34S is a surfactant. Metal recovery is better than 90% and the coprecipitate contains more than 10% U. The process is fast precipitation 10 minutes and flotation 5 minutes and is efficient even at 60 0 C [fr

Nitric-phosphoric acid oxidation of solid and liquid organic materials

International Nuclear Information System (INIS)

Pierce, R.A.; Smith, J.R.; Poprik, D.C.

1995-01-01

Nitric-phosphoric acid oxidation has been developed specifically to address issues that face the Savannah River Site, other defense-related facilities, private industry, and small-volume generators such as university and medical laboratories. Initially tested to destroy and decontaminate SRS solid, Pu-contaminated job-control waste, the technology has also exhibited potential for remediating hazardous and mixed-hazardous waste forms. The process is unique to Savannah River and offers a valuable alternative to other oxidation processes that require extreme temperatures and/or elevated pressures. To address the broad categories of waste, many different organic compounds which represent a cross-section of the waste that must be treated have been successfully oxidized. Materials that have been quantitatively oxidized at atmospheric pressure below 180 degrees C include neoprene, cellulose, EDTA, tributylphosphate, and nitromethane. More stable compounds such as benzoic acid, polyethylene, oils, and resins have been completely decomposed below 200 degrees C and 10 psig. The process uses dilute nitric acid in a concentrated phosphoric acid media as the main oxidant for the organic compounds. Phosphoric acid allow nitric acid to be retained in solution well above its normal boiling point. The reaction forms NOx vapors which can be reoxidized and recycled using air and water. The addition of 0.001M Pd(II) reduces CO generation to near 1% of the released carbon gases. The advantages of this process are that it is straightforward, uses relatively inexpensive reagents, operates at relatively low temperature and pressure, and produces final solutions which are compatible with stainless steel equipment. For organic wastes, all carbon, hydrogen, and nitrogen are converted to gaseous products. If interfaced with an acid recovery system which converts NOx back to nitric acid, the net oxidizer would be oxygen from air

Absorption characteristics of Kupravas deposit clays modified by phosphoric acid

International Nuclear Information System (INIS)

Ruplis, A.; Mezinskis, G.; Chaghuri, M.

1998-01-01

Literature data suggested that clays may be used as sorbents for waste water treatment. The surface and sorption properties of minerals changes due to the influence of acid rains. The process of recession of clay properties has been modeled in laboratory by treatment of clays with mineral acids at higher temperature that in natural conditions. The present paper is devoted to the study of influence of phosphoric acid on the sorption properties of Kupravas deposit clays. Natural clay samples and samples treated with phosphoric acid were characterized by means of x-ray diffraction an differential thermal analysis (DTA) methods These methods were used also to identify the sample of Lebanese clays. X-ray diffraction analysis data show that the samples of clays from the deposit of Kuprava contain illite and kaolinite while sample of Lebanese clay contains quartz, calcite, and montmorillonite. DTA results show characteristic features of Kuprava clays described in reference with DTA of Lebanese clay clearly demonstrate the presence of large quantity of calcite

Effect of phosphoric acid on the morphology and tensile properties of halloysite-polyurethane composites

Science.gov (United States)

Gaaz, Tayser Sumer; Luaibi, Hasan Mohammed; Al-Amiery, Ahmed A.; Kadhum, Abdul Amir H.

2018-06-01

The high aspect ratio of nanoscale reinforcements enhances the tensile properties of pure polymer matrix. The composites were first made by adding halloysite nanotubes (HNTs) at low weight percentages of 1, 2, and 3 wt% to thermoplastic polyurethane (TPU). Then, HNTs were phosphoric acid-treated before adding to TPU at same weight percentage to create phosphoric acid HNTs-TPU composites. The samples were fabricated using injection moulding. The HNTs-TPU composites were characterized according to the tensile properties including tensile strength, tensile strain and Young's modulus. The loading has shown its highest tensile values at 2 wt% HNTs loading and same findings are shown with the samples that treated with phosphoric acid. The tensile strength increased to reach 24.65 MPa compare with the 17.7 MPa of the neat TPU showing about 26% improvement. For the phosphoric acid-treated composites, the improvement has reached 35% compared to the neat sample. Regarding the tensile stain, the improvement was about 83% at 2 wt% HNTs loading. For Young's modulus, the results obtained in this study have shown that Young's modulus is linearly improved with either the loading content or the phosphoric acid treated achieving its highest values at 3 wt% HNTs of 14.53 MPa and 16.27 MPa for untreated and treated, respectively. FESEM results showed that HNTs were well dispersed in TPU matrix. Thus, HNTs-TPU has improved tensile properties compared with pure TPU due to the addition of nanofiller.

Fluoride removal performance of phosphoric acid treated lime ...

African Journals Online (AJOL)

Fluoride in drinking water above permissible levels is responsible for dental and skeletal fluorosis. In this study, removal of fluoride ions from water using phosphoric acid treated lime was investigated in continuous and point-of-use system operations. In the continuous column operations, fluoride removal performance was ...

Recent studies of uranium recovery from wet-process phosphoric acid with octylphenyl acid phosphate

International Nuclear Information System (INIS)

Arnold, W.D.

1978-01-01

Commercial OPAP is a complex mixture that contains at least 11 components. Octyl phenol is the principal impurity. Commercial OPAP contains readily-hydrolyzable material. The concentrations of octyl phenol and an unidentified impurity increase in the hydrolyzed product. Uranium extraction power is decreased slightly by hydrolysis of the reagent. Four major problems were encountered in continuous stability tests: (1) Microemulsion or micelle formation--loss of organic phase into phosphoric acid. We do not have a solution to this problem at this time. It could involve alteration of the organic, e.g., adding a modifier, changing the reagent structure, or changing the diluent. (2) Reagent poisoning--reduction of uranium extraction and interference with organic titrations by material extracted from the acid. Additional work is needed to identify the poisoning material or materials. It can then be removed if it originates in the phosphate rock, or avoided if it originates in chemicals added during processing. (3) Crystallization with iron--loss of both major components of the reagent as a complex with ferric iron. We believe this problem can be controlled by controlling the ferric iron concentration in the phosphoric acid. (4) MOPPA distribution loss--a selective loss to the aqueous phase. We believe this can be minimized by controlling the iron concentration of the phosphoric acid. The iron concentration will need to be kept low enough to avoid reagent crystallization and high enough to avoid MOPPA distribution loss. 15 figs

Structural and morphological changes in supramolecular-structured polymer electrolyte membrane fuel cell on addition of phosphoric acid

Science.gov (United States)

Hendrana, S.; Pryliana, R. F.; Natanael, C. L.; Rahayu, I.

2018-03-01

Phosphoric acid is one agents used in membrane fuel cell to modify ionic conductivity. Therefore, its distribution in membrane is a key parameter to gain expected conductivity. Efforts have been made to distribute phosphoric acid in a supramolecular-structured membrane prepared with a matrix. To achieve even distribution across bulk of the membrane, the inclusion of the polyacid is carried out under pressurized chamber. Image of scanning electron microscopy (SEM) shows better phosphoric acid distribution for one prepared in pressurized state. It also leads in better performing in ionic conductivity. Moreover, data from differential scanning calorimetry (DSC) indicate that the addition of phosphoric acid is prominent in the change of membrane structure, while morphological changes are captured in SEM images.

Synthesis and characterization of new biopolymeric microcapsules containing DEHPA-TOPO extractants for separation of uranium from phosphoric acid solutions.

Science.gov (United States)

Outokesh, Mohammad; Tayyebi, Ahmad; Khanchi, Alireza; Grayeli, Fatemeh; Bagheri, Ghodrat

2011-01-01

A novel microcapsule adsorbent for separation of uranium from phosphoric acid solutions was developed by immobilizing the di(2-ethylhexyl) phosphoric acid-trioctyl phosphine oxide extractants in the polymeric matrix of calcium alginate. Physical characterization of the microcapsules was accomplished by scanning electron microscopy and thermogravimetric techniques. Equilibrium experiments revealed that both ion exchange and solvent extraction mechanisms were involved in the adsorption of [Formula: see text] ions, but the latter prevailed in a wider range of acid concentration. According to the results of kinetics study, at low acidity level, the rate controlling step was slow chemical reaction of [Formula: see text] ions with the microdroplets of extractant, whereas it changed to intraparticle diffusion at higher acid concentration. The study also attempted identification of the diffusion paths of the ions within the microcapsules, and the mechanism of change of mass transfer rate during the uptake process. The prepared microcapsules preserved their entire capacity after three cycles of adsorption, and their breakthrough behaviour was well fitted by a new formula derived from shrinking core model.

Activated carbon from peach stones using phosphoric acid activation at medium temperatures.

Science.gov (United States)

Kim, Dong-Su

2004-01-01

In the present study, the activation features of phosphoric acid have been investigated using waste peach stones as the raw material in the production of granular activated carbon. Thermogravimetry/differential thermal analysis was conducted to characterize the thermal behavior of peach stone and titration method was used to evaluate the adsorption capacity of the produced activated carbon. It was observed that the iodine value of the activated carbon increased with activation temperature. However, temperatures higher than 500 degrees C caused a thermal destruction, which resulted in the decrease of the adsorption capacity. Activation longer than 1.5 h at 500 degrees C resulted in thermal degradation of the porous structure of the activated carbon. The adsorption capacity was enhanced with increasing of amounts of phosphoric acid, however, excessive phosphoric acid caused a decrease in the iodine value. In addition, it was found that the carbon yields generally decreased with activation temperature and activation time. Scanning electron microscopy analysis was conducted to observe the changes in the poros structure of the activated carbon produced in different temperatures. Activation of carbon by phosphoric acid was found to be superior to that by CaCl2 and gas activation. The activated carbon produced from peach stone was applied as an adsorbent in the treatment of synthesized wastewater containing cadmium ion and its adsorption capacity was found to be as good as that of the commercial one.

Procedure for recovery from an uranium containing concentrate and phosphoric acid, as well as an uranium containing concentrate and phosphoric acid obtained by this procedure

International Nuclear Information System (INIS)

1980-01-01

The phosphate ore is dissolved in sulphuric acid and the formed calcium sulphate is separated from the solution. The uranium is then precipitated by adding ammonium fluoride solution to the remaining phosphoric acid solution. When the phosphate ore is dissolved in sulphuric acid, fluorine gas is liberated and this is then used to produce the ammonium fluoride solution. (Th.P.)

Distribution of lanthanum and neodymium in Di(2-ethlhexyl) phosphoric acid and tributylphosphate

International Nuclear Information System (INIS)

Kraikaew, J.; Suparith, N.; Pruantonsai, P.

1994-01-01

Lanthanum and neodymium are among the high quantity elements in mixed rare earth from monazite processing. The popular rare earth separation process is liquid-liquid extraction. This research was carried out to study lanthanum and neodymium distribution in two extractants, di(2-ethylhexyl) phosphoric acid and tributylphosphate. The experimental results show that neodymium distributes in both extractants better than lanthanum. The distribution of both elements are higher at low acidity than at high acidity. Quick and rough investigation by calculating the ratio of distribution coefficient of neodymium to lanthanum in each extractant indicated that La-nd separation efficiency of Di(2-ethylhexyl) phosphoric acid is higher than that of tributylphosphate

Determination of formal potential of Amsup((4))/Amsup((3)) pair in phosphoric-acid solutions

International Nuclear Information System (INIS)

Mikhajlov, V.M.; Myasoedov, B.F.

1977-01-01

Values of formal potentials of the system Amsup((4))/Amsup((3)) in 12 and 15 M phosphoric acid at 20+-2 deg C are determined by potentiometric method. The effect is studied of metallic platinum on the process of self-reduction of tetravalent americium, and the optimum conditions are found for potentiostatic oxidation of Amsup((3)) to Amsup((4)) in 12 M phosphoric acid

Study of phosphoric acid crystallization using a focused beam reflectance measurement method

Energy Technology Data Exchange (ETDEWEB)

Ma, Yong [School of Chemistry and Resource Environment, Linyi Normal University, Linyi Shandong 276005 (China); Chen, Kui; Wu, Yanyang; Zhu, Jiawen [Chemical Engineering Research Center, East China University of Science and Technology, Shanghai 200237 (China); Sheng, Yong [SINOCHEN Fuling Chemical Industrial Co., Ltd, Chongqing 226005 (China)

2010-10-15

A way for restoring the crystal size distributions (CSD) from measured chord length distributions (CLD) was reported in this paper. The kinetics of phosphoric acid crystallization process was investigated in cooling mode using focused beam reflectance measurement (FBRM) and digital photo technique. In order to restore the CSD from measured CLD and verify the reliability of FBRM data, digital photo technique in real time and optical microscope were applied in large crystal size and small range, respectively. Results indicated a converting constant A existed between CLD and CSD when crystal growth follows size-independent growth (Mcabe's {delta}L law) law. It was verified by Malvern particles size analysis method. The converting constant A varied with crystal morphology. The crystal growth order increased with the stirring increasing speed during phosphoric acid crystallization process. The trend was especially notable at higher speed situations. It can illustrate that the state of phosphoric acid hemihydrate crystal growth was controlled by both diffusion and surface-integration with the increasing stirring speed. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Shear bond strength of self-etch adhesives to enamel with additional phosphoric acid etching.

Science.gov (United States)

Lührs, Anne-Katrin; Guhr, Silke; Schilke, Reinhard; Borchers, Lothar; Geurtsen, Werner; Günay, Hüsamettin

2008-01-01

This study evaluated the shear bond strength of self-etch adhesives to enamel and the effect of additional phosphoric acid etching. Seventy sound human molars were randomly divided into three test groups and one control group. The enamel surfaces of the control group (n=10) were treated with Syntac Classic (SC). Each test group was subdivided into two groups (each n=10). In half of each test group, ground enamel surfaces were coated with the self-etch adhesives AdheSe (ADH), Xeno III (XE) or Futurabond NR (FNR). In the remaining half of each test group, an additional phosphoric acid etching of the enamel surface was performed prior to applying the adhesives. The shear bond strength was measured with a universal testing machine at a crosshead speed of 1 mm/minute after storing the samples in distilled water at 37 degrees C for 24 hours. Fracture modes were determined by SEM examination. For statistical analysis, one-way ANOVA and the two-sided Dunnett Test were used (p>0.05). Additional phosphoric etching significantly increased the shear bond strength of all the examined self-etch adhesives (padhesive fractures. For all the self-etch adhesives, a slight increase in mixed fractures occurred after conditioning with phosphoric acid. An additional phosphoric acid etching of enamel should be considered when using self-etch adhesives. More clinical studies are needed to evaluate the long-term success of the examined adhesives.

Extractants for uranium recovery from wet phosphoric acid

International Nuclear Information System (INIS)

Musikas, C.; Benjelloun, N.; Lours, S.

1982-01-01

Synergistic mixtures containing phosphine oxide plus one of the acidic extractants: dialkyldithiophosphoric acid, dialkylthiophosphoric acid and dialkylphosphoric acid have been compared with respect to U(VI) and Fe(III) extraction from wet phosphoric acid. Distribution curves slope analysis showed that U(VI) extraction mechanisms are totally different. It has been found that U(VI) is extracted as: UO 2 (H 2 PO 4 )(DEHDTP)(TOPO) ; UO 2 (H 2 PO 4 )(DBTP)(POX) 2 and UO 2 (DEHP)(HDEHP) 2 TOPO in dodecane solutions containing di 2 ethylhexyldithiophosphoric acid (HDEHDTP) or dibutylthiophosphoric acid (HDBTP) or di-2-ethylhexylphosphoric acid (HDEHP) plus a phosphine oxide (TOPO or dihexylmethoxyoctylphosphine oxide (POX 11)). The synergistic mixtures containing HDEHDTP gave the highest U(VI) distribution coefficients. Back extraction with oxalic solutions can be achieved only with the synergistic mixtures containing the acidic thiophosphoric donors

Synthesis of new polyphosphonic acids, uranium extracting agents in a phosphoric medium

International Nuclear Information System (INIS)

Pensec, T.

1981-04-01

Synthesis of organic phosphorus compounds for liquid-liquid extraction of traces of uranium in concentrated phosphoric acid is studied in view of industrial applications. Diphosphonic acids and monoesters and also triphosphonic acids and related compounds are synthetized. Extraction tests show a better efficiency than OPPA [fr

Solid phase extraction of uranium from phosphoric acid. Kinetic and thermodynamic study

Energy Technology Data Exchange (ETDEWEB)

Abdel-Magied, Ahmed Fawzy [Nuclear Materials Authority, Cairo (Egypt); Stockholm Univ. (Sweden). Dept. of Organic Chemistry

2017-07-01

There is a high interest to develop suitable solid phase extractants for uranium separation from aqueous solutions in order to reduce cost and enhance the efficiency. This paper describes solid phase extraction of uranium(VI) from aqueous phosphoric acid solution using MCM-41 based D2HEPA-TOPO organophosphorous extractants. The mixture of D2HEPA (di-2-ethyl-hexylphosphoric acid) and TOPO (tri-n-octylphosphine oxide) was impregnated into the pores of MCM-41 and the synthesized sorbent was fully characterized. The influences of different factors such as synergistic mixture ratio, phosphoric acid concentration, mixing time and temperature were investigated. The results showed that 90% of uranium(VI) extraction can be achieved within 5 min, using D2HEPA-TOPO rate at MCM-41 (mass ratio 2:1 w/w) from 1 M phosphoric acid containing 64 ppm of uranium at room temperature. High adsorption capacity of uranium(VI) have been achieved at the mentioned conditions. The rate constant for the chemical adsorption of uranium(VI) was 0.988 g mg{sup -1} min{sup -1} calculated by the pseudo-second order rate equation. The obtained thermodynamics parameters showed that uranium(VI) adsorption from H{sub 3}PO{sub 4} is an exothermic and spontaneous process.

The use of ion chromatography for the determination of impurities in crude phosphoric acid

International Nuclear Information System (INIS)

Pires, M.A.F.; Atalla, L.T.; Abrao, A.

1988-07-01

The determination of fluoride, nitrate, sulphate and phosphate ions in crude phosphoric acid by means of ion chromatography is described. A previous separation of interferent cations was made by using a cationic resin or EDTA complexation. The last alternative allowed more reproductible results. The technique described is very quick and is being applied for the simultaneous determination of impurities in phosphoric acid and its own phosphospate concentration. The method is quick and has good reprodutibility. (author) [pt

46 CFR 153.558 - Special requirements for phosphoric acid.

Science.gov (United States)

2010-10-01

... CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and... containment system must be: (a) Lined with natural rubber or neoprene; (b) Lined with a material approved for phosphoric acid tanks by the Commandant (CG-522); or (c) Made of a stainless steel that resists corrosion by...

Analytical applications of condensed phosphoric acid-I Determination of ferrous and total iron in iron ores after decomposition with condensed phosphoric acid.

Science.gov (United States)

Mizoguchi, T; Ishii, H

1978-06-01

A simple method is described for the determination of ferrous and total iron in iron ores. Iron ores are dissolved by condensed phosphoric acid (CPA) very rapidly without any tedious and time-consuming manipulations such as elimination of silica and filtration. Under the proposed conditions (amount of sample 100 mg, amount of CPA added 10 g, heating temperature 290 degrees , heating time 30 min), magnetite, limonite and hematite are completely dissolved. The iron content can be determined in the presence of condensed phosphoric acid by titration with dichromate solution, if a slight modification is made. The total iron in iron ores, determined by the present method, is in agreement with that found by the JIS method. The ferrous iron in iron ores can be determined by dissolving the samples with CPA in a nitrogen atmosphere and titrating with dichromate solution. Chelatometric titration of iron after solvent extraction with MIBK from solutions prepared by use of CPA is found to be accurate for samples such as pyrite cinder. The ability of CPA to dissolve various materials has been investigated.

Study of uranium(VI) speciation in phosphoric acid solutions and of its recovery by solvent extraction

International Nuclear Information System (INIS)

Dartiguelongue, Adrien

2014-01-01

Because small amounts of uranium are present in phosphate rocks, wet phosphoric acids may contain up to 300 ppm of uranium(VI). Therefore, such acids are a cost-effective unconventional source of this metal. Its recovery is a challenge for metallurgical firms which must develop reliable and selective solvent extraction processes. Such processes need to know the chemical equilibria involved in the extraction process, the speciation of uranium and its thermodynamics in solution. These two last points have been investigated in this work. Firstly, the most probable species of uranium(VI) in phosphoric acid solutions have been selected thanks to a detailed review of the literature. Then, a thermodynamic model founded on an equation of state for electrolytes has been built according these hypotheses. It has been validated with speciation data coming from original ATR-IR spectroscopy measurements. Finally, the composition of the aqueous phosphoric acid solutions and the activity coefficients obtained have been combined with a chemical model of uranium(VI) extraction into an organic phase containing a synergistic mixture of bis(2-ethylhexyl)phosphoric acid (D2EHPA) and tri-n-octylphosphine oxide (TOPO) in order to represent the variation of the distribution coefficient of uranium(VI) with H 3 PO 4 concentration. This model had been previously developed at Chimie ParisTech at a given concentration of H 3 PO 4 (i.e., 5,3 mol/L), but in the present study we have tested its validity in an extended range of phosphoric acid concentrations (i.e., 1-7 mol/L) and improved it. (author)

Comparison of enamel bond fatigue durability between universal adhesives and two-step self-etch adhesives: Effect of phosphoric acid pre-etching.

Science.gov (United States)

Suda, Shunichi; Tsujimoto, Akimasa; Barkmeier, Wayne W; Nojiri, Kie; Nagura, Yuko; Takamizawa, Toshiki; Latta, Mark A; Miyazaki, Masashi

2018-03-30

The effect of phosphoric acid pre-etching on enamel bond fatigue durability of universal adhesives and two-step self-etch adhesives was investigated. Four universal adhesives and three two-step self-etch adhesives were used. The initial shear bond strengths and shear fatigue strengths to enamel with and without phosphoric acid pre-etching using the adhesives were determined. SEM observations were also conducted. Phosphoric acid pre-etching of enamel was found to increase the bond fatigue durability of universal adhesives, but its effect on two-step self-etch adhesives was material-dependent. In addition, some universal adhesives with phosphoric acid pre-etching showed similar bond fatigue durability to the two-step self-etch adhesives, although the bond fatigue durability of universal adhesives in self-etch mode was lower than that of the two-step self-etch adhesives. Phosphoric acid pre-etching enhances enamel bond fatigue durability of universal adhesives, but the effect of phosphoric acid pre-etching on the bond fatigue durability of two-step self-etch adhesives was material-dependent.

Gel Electrolytes of Covalent Network Polybenzimidazole and Phosphoric Acid by Direct Casting

DEFF Research Database (Denmark)

Kirkebæk, Andreas; Aili, David; Henkensmeier, Dirk

2017-01-01

for preparing mechanically robust covalent network polybenzimidazole membranes containing up to 95 wt% phosphoric acid. Diamino-terminal pre-polymers of different chain lengths are first prepared, followed by addition of a trifunctional carboxylic acid. The crude solutions are cast and subsequently heat treated...

Study of the mechanism and kinetics of the reduction of uranyl ions in phosphoric acid solutions

International Nuclear Information System (INIS)

El Kacemi, K.; Tyburce, B.; Belcadi, S.

1982-01-01

The electrochemical reduction of uranyl ions in 0.1 to 9 M phosphoric acid has been investigated by polarography, cyclic voltammetry, chronopotentiometry and potentiostatic coulometry. In concentrated phosphoric acid solutions (H 3 PO 4 3 PO 4 concentrations. So, when the concentration of U(VI) increases and/or that of H 3 PO 4 reduces, the system becomes reversible. (author)

Solid-state actinide acid phosphites from phosphorous acid melts

International Nuclear Information System (INIS)

Oh, George N.; Burns, Peter C.

2014-01-01

The reaction of UO 3 and H 3 PO 3 at 100 °C and subsequent reaction with dimethylformamide (DMF) produces crystals of the compound (NH 2 (CH 3 ) 2 )[UO 2 (HPO 2 OH)(HPO 3 )]. This compound crystallizes in space group P2 1 /n and consists of layers of uranyl pentagonal bipyramids that share equatorial vertices with phosphite units, separated by dimethylammonium. In contrast, the reaction of phosphorous acid and actinide oxides at 210 °C produces a viscous syrup. Subsequent dilution in solvents and use of standard solution-state methods results in the crystallization of two polymorphs of the actinide acid phosphites An(HPO 2 OH) 4 (An=U, Th) and of the mixed acid phosphite–phosphite U(HPO 3 )(HPO 2 OH) 2 (H 2 O)·2(H 2 O). α- and β-An(HPO 2 OH) 4 crystallize in space groups C2/c and P2 1 /n, respectively, and comprise a three-dimensional network of An 4+ cations in square antiprismatic coordination corner-sharing with protonated phosphite units, whereas U(HPO 3 )(HPO 2 OH) 2 (H 2 O) 2 ·(H 2 O) crystallizes in a layered structure in space group Pbca that is composed of An 4+ cations in square antiprismatic coordination corner-sharing with protonated phosphites and water ligands. We discuss our findings in using solid inorganic reagents to produce a solution-workable precursor from which solid-state compounds can be crystallized. - Graphical abstract: Reaction of UO 3 and H 3 PO 3 at 100 °C and subsequent reaction with DMF produces crystals of (NH 2 (CH 3 ) 2 )[UO 2 (HPO 2 OH)(HPO 3 )] with a layered structure. Reaction of phosphorous acid and actinide oxides at 210 °C produces a viscous syrup and further solution-state reactions result in the crystallization of the actinide acid phosphites An(HPO 2 OH) 4 (An=U, Th), with a three-dimensional network structure, and the mixed acid phosphite–phosphite U(HPO 3 )(HPO 2 OH) 2 (H 2 O) 2 ·(H 2 O) with a layered structure. - Highlights: • U(VI), U(IV) and Th(IV) phosphites were synthesized by solution

Kinetic studies on uranium stripping in D2EHPA+TBP/phosphoric acid system

International Nuclear Information System (INIS)

Yadav, K.K.; Singh, D.K.; Kotekar, M.K.; Anitha, M.; Vijayalakshmi, R.; Singh, H.

2010-01-01

Full text: A novel process based on synergistic mixture of 1.5 M D2EHPA (di 2 ethyl hexyl phosphoric acid) + 0.2 M TBP (tri-n-butyl phosphate) to recover uranium from wet process phosphoric acid (WPA) has been developed. Though the equilibrium study for the above process has been investigated in detail its kinetic behavior has not been reported so far. The work presented in the paper is an attempt to study the kinetics of U(VI) stripping from extractant phase to aqueous phase in a constant interfacial area cell (Lewis cell). Kinetic study of the solvent extraction process helps in designing of equipment and optimizing process condition for the better utilization of solvent inventory. Mass transfer kinetics of stripping of U(VI) from loaded 1.5M D2EHPA+ 0.2M TBP with phosphoric acid (AR) has been studied over a wide range of experimental conditions such as stirring speed, interfacial contact area, phosphoric acid concentration, uranium concentration, extractant concentration in organic phase and temperature. Investigation on effect of stirring speed (100-500 rpm) on stripping of U(VI) showed that the rate constant (k) values increases linearly with increase in stirring speeds from 100 to 300 rpm (0.03 to 0.075 cm/min), while the k values were almost constant (0.0819 cm/min) in 300 to 400 rpm range, beyond 450 rpm the k values again increased due to increased turbulence at the interface. The rate constant value (∼0.0814 cm/min) was found to be independent of interfacial contact area (24.6 to 67.02 cm 2 ) available for mass transfer. The rate constants were found to increase with increase in phosphoric acid concentration (6-10M) and temperature (30-60 deg C), the values being in the range of 0.01 to 0.082 cm/min. The slopes of ln-ln plot showed that the stripping of U(VI) has a second order dependence on phosphoric acid concentration (slope∼2) at temperatures ranging from 30 to 60 deg C. The activation energy value for uranium stripping was found to be in the

Determination of uranium content in phosphoric and sulfuric acids used by the phosphatized fertilizers industry

International Nuclear Information System (INIS)

Ramos, M.M.O.

1984-05-01

Uranium content in phosphoric and sulfuric acids is determined. The uranium was measured through the fission track registration technique, using Makrofol KG, 10 μg thick, as detector. The so-called 'wet' method was adopted and the acid samples were used directly as irradiation medium. This proceeding showed the advantages of simple sample preparation and avoided the need of changing the acid samples media to nitric medium, as commonly used. The analysis of the sulfuric acid samples showed uranium contents under the detection limit of the technique (4 ppb). The results found for phosphoric acid samples ranged from 31 to 845 ppm, with experimental errors between 7.9 and 9.7%. (Author) [pt

Corrosion of graphite composites in phosphoric acid fuel cells

Science.gov (United States)

Christner, L. G.; Dhar, H. P.; Farooque, M.; Kush, A. K.

1986-01-01

Polymers, polymer-graphite composites and different carbon materials are being considered for many of the fuel cell stack components. Exposure to concentrated phosphoric acid in the fuel cell environment and to high anodic potential results in corrosion. Relative corrosion rates of these materials, failure modes, plausible mechanisms of corrosion and methods for improvement of these materials are investigated.

Direct uranium extraction from dihydrate and hemi-dihydrate wet process phosphoric acids by liquid emulsion membrane

International Nuclear Information System (INIS)

El-Hazek, N.T.; El Sayed, M.S.

2003-01-01

A new liquid emulsion membrane (LEM) process for uranium extraction from either dihydrate 28-30% P 2 O 5 (DH) or hemi-dihydrate 42-45% P 2 O 5 (HDH) wet process phosphoric acid is proposed. In this process, the organic component of the LEM is composed of a synergistic mixture of 0.1M di-2-ethyl hexyl phosphoric acid (DEHPA) and 0.025M trioctyl phosphine oxide (TOPO) with 4% Span 80. The internal or the strip acid phase is composed of 0.5M citric acid. The prepared LEM was proved to be stable in 42-45% P 2 O 5 acid concentration range and can, therefore, be applied to the phosphoric acid produced by the hemi-dihydrate process. After breakdown of the loaded emulsion, the uranyl citrate in the internal strip phase is separated by adding methanol followed by its calcination to the orange oxide. Most of the reagents used are recycled. The proposed process is characterized by simplicity, practically closed operation cycle in addition to lower capital and operating costs. (author)

230Th, 232Th and 238U determinations in phosphoric acid fertilizer and process products by ICP-MS

International Nuclear Information System (INIS)

Nascimento, Marcos R.L. do; Guerreiro, Luisa M.R.; Bonifacio, Rodrigo L.; Taddei, Maria H.T.

2015-01-01

Through processing of Santa Quiteria-CE mine phosphate rock, Brazil has established a project for production of phosphoric acid fertilizer and uranium as a by-product. Under leaching conditions of phosphate rock with sulfuric acid, which is the common route for preparing phosphoric acid fertilizer, a large part of uranium, thorium and their decay products naturally present in the rock are solubilized. In order to assess the contamination potential in phosphoric acid and others process products, this paper describes a previous precipitation and direct methods for routine analysis of thorium and uranium isotopes by ICP-MS. In all samples, 230 Th, 232 Th and 238 U were directly determined after dilution, except 230 Th in phosphoric acid loaded with uranium sample, which to overcome equipment contamination effect, was determined after its separation by oxalate precipitation using lanthanum as a carrier. The results obtained by the proposed method by ICP-MS, were in good agreement when compared to alpha spectrometry for 230 Th, and ICP-OES and spectrophotometry with arsenazo III for elementary uranium and thorium determinations. (author)

Carbon-13 kinetic isotope effects in the decarbonylation of lactic acid of natural isotopic composition in phosphoric acid medium

International Nuclear Information System (INIS)

Zielinski, M.; Czarnota, G.; Papiernik-Zielinska, H.; Kasprzyk, G.; Gumolka, L.; Staedter, W.

1993-01-01

The 13 C kinetic isotope effect fractionation in the decarbonylation of lactic acid (LA) of natural isotopic composition by concentrated phosphoric acids (PA) and by 85% H 3 PO 4 has been studied in the temperature interval of 60-150 deg C. The values of the 13 C (1) isotope effects in the decarbonylation of lactic acid in 100% H 3 PO 4 , in pyrophosphoric acid and in more concentrated phosphoric acids are intermediate between the values calculated assuming that the C (1)- OH bond is broken in the rate-controlling step of dehydration and those calculated for rupture of the carbon-carbon bond in the transition state. In the temperature interval of 90-130 deg C the experimental 13 C fractionation factors determined in concentrated PA approach quite closely the 13 C fractionation corresponding to C (2)- C (1) bond scission. The 13 C (1) kinetic isotope effects in the decarbonylation of LA in 85% orthophosphoric acid in the temperature range of 110-150 deg C coincide with the 13 C isotope effects calculated assuming that the frequency corresponding to the C (1) -OH vibration is lost in the transition state of decarbonylation. A change of the mechanism of decarbonylation of LA in going from concentrated PA medium to 85% H 3 PO 4 has been suggested. A possible secondary 18 O and a primary 18 O kinetic isotope effect in decarbonylation of lactic acid in phosphoric acids media have been discussed, too. (author) 21 refs.; 3 tabs

Evaluation of Bio-phosphor and HumicAcid on Growth Parameters and Oil Content in Evening Primrose (Oenotherabiennis L.

Directory of Open Access Journals (Sweden)

Zeinab Aghakhani

2017-12-01

Full Text Available Introduction: Evening primrose (OenotherabiennisL. is a relatively new and valuable oilseed crop for temperate region. Its oilseed is important because of high levels of unsaturated fatty acids, especially gamma-linolenic acid. Seeds contain 20-30% oil which includes 70% linoleic acid (LA and 10% gamma linolenic acid (GLA. Oil content in O. biennis is a quantitative trait which controlled by many genes and similar to any other quantitative traits varies with environmental conditionssuch factors as age of seed and growth conditions. Evening primrose oil, especially gamma-linolenic acid, has many therapeutic properties, and it uses as cure for many diseases such as Diabetes, Eczema, inflammation, Cardiovascular, Cancer, Autoimmune diseases, Rheumatoid Arthritis, Depression. Studies on Medicinal Plants in nature and farmlands show that the use of sustainable agriculturae andnatural sources are two suitable methods for producing healthy plants.Additionally, the use of bio-fertilizers lead to maximum yield and quality in these plants. Azizi et al.(6 showed that interactions of vermicompost and plant density had significant effect on oil content, oil density and refractive index of evening primrose oil. The best treatments were also including 2 Kg/m2 of vermicompost,20 plants/ m2in terms of oil production,9 plants/ m2in terms of oil quality and ratio of unsaturated fatty acids to saturated, respectively. Material and Method: The aim of this research was to determine the effect of humic acid and bio-phosphor application on growth parameters in O. biennis. The experiment was conducted based on randomized complete block design with 8 treatments and three replicates during 2013-2014 growing season, at the experimental farm of the faculty of Agriculture, Ferdowsi University of Mashhad.. Treatments consisted of 4 levels of humic acid (0, 1, 3, 5 ml/L and 2 levels of bio-phosphor (without bio-phosphor or with bio-phosphor. Liquid form of humic acid was used

Unexpected 226Ra build-up in wet-process phosphoric-acid plants

International Nuclear Information System (INIS)

Lardinoye, M.H.; Weterings, K.; Berg, W.B. van de

1982-01-01

During an investigation of the distribution of radium and uranium over the different process streams in phosphoric-acid production and in the nitrophosphate route, a higher than average radiation level was detected in the vicinity of some piping and vessels near the gypsum filters. This higher radiation level is caused by radium which is present in very low concentrations in the phosphates used for fertilizer production. Detectable radiation levels around vessels and piping in other phosphoric-acid works have since been determined. In all factories the filter part and especially the washing-acid section showed the highest radiation level. In the piping of the gypsum filter, through which the washing acid is discharged, a scaling of barium sulphate and calcium sulphate with a higher radium concentration is formed. The radium ions appeared to be incorporated in the barium sulphate lattice, hence the solubility of the radium precipitate is very low. The danger of internal contamination in cleaning operations by radioactive intake or inhalation of radon is very small in the cases described. The risk of external radiation can be prevented by periodically cleaning the equipment in which the radioactive scaling is formed. (author)

Temperature dependence and P/Ti ratio in phosphoric acid treatment of titanium dioxide and powder properties.

Science.gov (United States)

Onoda, H; Matsukura, A

2015-02-01

Titanium dioxide has photocatalytic activity and is used as a white pigment for cosmetics. A certain degree of sebum on the skin is decomposed by the ultraviolet radiation in sunlight. In this work, titanium dioxide was shaken with phosphoric acid to synthesize a white pigment for cosmetics. Titanium dioxide was treated with 0.1 mol/L of phosphoric acid at various P/Ti molar ratios, and then shaken in hot water for 1 h. The chemical composition, powder properties, photocatalytic activity, colour phase, and smoothness of the obtained powder were studied. The obtained materials indicated XRD peaks of titanium dioxide, however the peaks diminished subsequent to phosphoric acid treatment. The samples included small particles with sub-micrometer size. The photocatalytic activity of the obtained powders decreased, decomposing less sebum on the skin. Samples prepared at high P/Ti ratio with high shaking temperature indicated low whiteness in in L*a*b* colour space. The shaking and heating temperature and P/Ti ratio had influence on the smoothness of the obtained materials. Phosphoric acid treatment of titanium dioxide is an effective method to inhibit photocatalytic activity for a white pigment. © 2014 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Radioactivity Content in Phosphoric Acid Used for Fertilizer Production

International Nuclear Information System (INIS)

Ibrahiem, N.M.; Hamed, A.A.

2003-01-01

Uranium content in phosphoric acid used fertilizer production was measured by alpha spectrometry, laser fluorimetry high resolution gamma spectrometry. Also, polonium-210 content was determined in phosphoric acid by alpha spectrometry. Uranium-234 and uranium-238 concentrations, measured by alpha spectroscopy, were found to be 601 and 507 Bq I -1 , respectively. Total uranium content obtained by laser fluorimetry was about 545 BqI - (45.4ppm). Gamma spectroscopy analysis gave the concentrations of 40 K, 238 U, 235 U, 214 Pb, 214 Bi and 208 TI, as 17,644,19.5, 1.2,1.3 and 9.4 Bq I -1 , respectively. Polonium-210 concentration was found to be about 3.1 Bq I -1 . Uranium-232 and polonium-208 were used as yield tracers, for alpha measurements of uranium and polonium, respectively. Samples of the tri-super phosphate (TSP) and single-super phosphate (SSP) fertilizers and the phosphogypsum produced were also analyzed by gamma spectroscopy. Uranium content in both phosphate fertilizers was 3205 and 1440 Bq Kg -1 for 238 U and 83 and 35 Bq Kg -1 for, 235 U respectively

A process for uranium recovery in phosphoric acid

International Nuclear Information System (INIS)

Duarte Neto, J.

1984-01-01

Results are presented about studies carried out envisaging the development of a process for uranium recovery from phosphoric acid, produced from the concentrate obtained from phosphorus-uraniferous mineral from Itataia mines (CE, Brazil). This process uses a mixture of DEPA-TOPO as extractant and the extraction cycle involves the following stages: acid pre-treatment; adjustment of the oxidation potential so to ensure that all uranium is hexavalent; extraction of uranium from the acid; screening of the solvent to remove undesirable impurities; uranium re-extraction and precipitation; solvent recovery. A micro-pilot plant for continuous processing was built up. Data collected showed that uranium can be recovered with an yield greater than 99%, thus proving the feasibility of the process and encouraging the construction of a bigger scale plant. (Author) [pt

Extraction of americium from acid aqueous solutions by diethyl-2-hexyl-pyro-phosphoric acid

International Nuclear Information System (INIS)

Guillaume, Bernard

1971-02-01

After having outlined the interesting properties of americium and the difficulties of its recovery, the author reports the study of the mechanism of extraction of americium from acid aqueous solutions by using the diethyl-2hexyl-pyro-phosphoric acid. Several aspects are thus discussed: influence of concentration of H 2 DEHPP, influence of the acidity of the aqueous phase, saturation of extracting agent, influence of the diluting agent, complexing of americium, influence of other cations. In a second part, the author reports the application to the recovery of americium from effluents, and discusses the obtained results

Phosphoric acid doped AB-PBI membranes and its applications in high temperature PEMFC

DEFF Research Database (Denmark)

He, Ronghuan; Qingfeng, Li; Bjerrum, Niels

2005-01-01

Poly(2,5-benzimidazole) (ab-PBI) was prepared from 3，4-diaminobenzoic acid via a polymerisation reaction. The obtained polymer exhibits excellent thermal stability in a temperature range ….. The membrane of ab-PBI when doped with phosphoric acid at room temperaturepresents high proton conductivity...

Interim solidification of SRP waste with silica, bentonite, or phosphoric acid

International Nuclear Information System (INIS)

Thompson, G.H.

1976-03-01

One option for interim waste management at the Savannah River Plant is in-tank solidification of the liquid waste solutions. This would reduce the mobility of these highly radioactive solutions until techniques for their long-term immobilization and storage are developed and implemented. Interim treatments must permit eventual retrieval of waste and subsequent incorporation into a high-integrity form. This study demonstrated the solidification of simulated alkaline waste solutions by reaction with silica, bentonite, and phosphoric acid. Alkaline waste can be solidified by reaction with silica gel, silica flour, or sodium silicate solution. Solidified products containing waste salt can be retrieved by slurrying with water. Alkaline supernate (solution in equilibrium with alkaline sludge in SRP waste tanks) can be solidified by reaction with bentonite to form cancrinite powder. The solidified waste can be retrieved by slurrying with water. Alkaline supernate can be solidified by partial evaporation and reaction with phosphoric acid. Water is incorporated into hydrated complexes of trisodium phosphate. The product is soluble, but actual plant waste would not solidify completely because of decay heat. Reaction of simulated alkaline waste solutions with silica gel, silica flour, or bentonite increases the volume by a factor of approximately 6 over that of evaporated waste; reaction with phosphoric acid results in a volume 1.5 times that of evaporated waste. At present, the best method for in-tank solidification is by evaporation, a method that contributes no additional solids to the waste and does not compromise any waste management options

Online Automatic Titration of Chromic Acid in Chromium Plating Solutions and Phosphoric and Sulfuric Acids in Electropolishing Solutions

National Research Council Canada - National Science Library

Sopok, Samuel

1991-01-01

.... The analytical chemistry literature lacks an adequate online automatic titration method for the monitoring of chromic acid in chromium plating solutions and the monitoring of phosphoric and sulfuric...

Improvement of Haramay Fiber by Pre-treatment of Retting Process withPhosphoric Acid

International Nuclear Information System (INIS)

Kuntari-Sasas; Neni-Rustini Eriawati

2000-01-01

Haramay as bast fiber contains of cellulose fiber as the main part, mixedwith hemi cellulose, pectin, and lignin as binding material for cellulosefiber to keep it together in the bundle form. For textile material, this bastfiber has to be freed from its binding material, called as retting process,before subjecting to scouring, dyeing and finishing process in textileindustry. In the retting process the dissolve of binding material can be doneeither by using enzyme in bio technology or extraction with strong alkalinecondition in common technology. Using sodium hydroxide for dissolving thebinding material can be carried out easily with good dissolving ability, butcan render the strength retention of the cellulose fiber. Pre-treatment ofthe bast fiber with phosphoric acid (H 3 PO 4 ), is expected to hydrolyze someof the binding materials that can not be dissolved in alkaline condition,including natural pigment that colored the fiber with creamy white. In thisstudy, the pre-treatment process before retting with phosphoric acid wascarried out in various condition, such as concentration of phosphoric acid (5ml/l- 25 ml/l), time and temperature of pre-treatment (1-3 hours at 50 o C or12-24 hours at room temperature), followed by neutralization in dilutealkaline. The retting process was carried out by means of scouring in variousconcentration of sodium hydroxide (NaOH 38 o Be, 10 ml/l-30 m/l), and then wascontinued with bleaching process in hydrogen peroxide solution. Aftercarrying out those experiment, the bast fiber that called haramay wassubjected to testing for weight reduction, strength retention and degree ofwhiteness. From the testing results it is concluded that pre-treatment withphosphoric acid can increase the weight reduction, strength retention ortenacity and degree of whiteness of haramay fiber compared to the oneswithout pre-treatment with phosphoric acid. The best result was obtained bypre-treatment with 5 ml/l H 3 PO 4 at 50 o C for 2 hours, continued by

Phosphoric acids as amplifiers of molecular chirality in liquid crystalline media

NARCIS (Netherlands)

Eelkema, R; Feringa, BL

2006-01-01

A new system for the double amplification of the molecular chirality of simple chiral amines in achiral liquid crystalline media is described. It involves a conformationally flexible phosphoric acid based receptor that by binding to chiral amines induces chirality in the liquid crystalline matrix.

Alternative processes for uranium recovery from phosphoric acid

International Nuclear Information System (INIS)

Duarte Neto, J.; Santos Benedetto, J. dos; Aquino, J.A. de

1987-01-01

Two processes of solvent extraction using D 2 EHPATOPO synergistic mixture, in order to recover uranium from phosphoric acid proceeding from physical and chemical treatments of the phosphorus-uraniferous ore of Itataia-CE, Brazil, are studied. The steps of each process were studied in laboratory and pilot scales. The flow charts for both processes with detailed description of each step, the operational conditions, the mass balances, the results obtained and the description of pilot units, are presented. (M.C.K.) [pt

Wet Chemical Oxidation of Organic Waste Using Nitric-Phosphoric Acid Technology

Energy Technology Data Exchange (ETDEWEB)

Pierce, R.A.

1998-10-06

Experimental progress has been made in a wide range of areas which support the continued development of the nitric-phosphoric acid oxidation process for combustible, solid organic wastes. An improved understanding of the overall process operation has been obtained, acid recovery and recycle systems have been studied, safety issues have been addressed, two potential final waste forms have been tested, preliminary mass flow diagrams have been prepared, and process flowsheets have been developed. The flowsheet developed is essentially a closed-loop system which addresses all of the internally generated waste streams. The combined activities aim to provide the basis for building and testing a 250-400 liter pilot-scale unit. Variations of the process now must be evaluated in order to address the needs of the primary customer, SRS Solid Waste Management. The customer is interested in treating job control waste contaminated with Pu-238 for shipment to WIPP. As a result, variations for feed preparation, acid recycle, and final form manufacturing must be considered to provide for simpler processing to accommodate operations in high radiation and contamination environments. The purpose of this program is to demonstrate a nitric-phosphoric acid destruction technology which can treat a heterogeneous waste by oxidizing the solid and liquid organic compounds while decontaminating noncombustible items.

Influence of multi-step washing using Na2EDTA, oxalic acid and phosphoric acid on metal fractionation and spectroscopy characteristics from contaminated soil.

Science.gov (United States)

Wei, Meng; Chen, Jiajun

2016-11-01

A multi-step soil washing test using a typical chelating agent (Na 2 EDTA), organic acid (oxalic acid), and inorganic weak acid (phosphoric acid) was conducted to remediate soil contaminated with heavy metals near an arsenic mining area. The aim of the test was to improve the heavy metal removal efficiency and investigate its influence on metal fractionation and the spectroscopy characteristics of contaminated soil. The results indicated that the orders of the multi-step washing were critical for the removal efficiencies of the metal fractions, bioavailability, and potential mobility due to the different dissolution levels of mineral fractions and the inter-transformation of metal fractions by XRD and FT-IR spectral analyses. The optimal soil washing options were identified as the Na 2 EDTA-phosphoric-oxalic acid (EPO) and phosphoric-oxalic acid-Na 2 EDTA (POE) sequences because of their high removal efficiencies (approximately 45 % for arsenic and 88 % for cadmium) and the minimal harmful effects that were determined by the mobility and bioavailability of the remaining heavy metals based on the metal stability (I R ) and modified redistribution index ([Formula: see text]).

The Effect of Phosphoric Acid Pre-etching Times on Bonding Performance and Surface Free Energy with Single-step Self-etch Adhesives.

Science.gov (United States)

Tsujimoto, A; Barkmeier, W W; Takamizawa, T; Latta, M A; Miyazaki, M

2016-01-01

The purpose of this study was to evaluate the effect of phosphoric acid pre-etching times on shear bond strength (SBS) and surface free energy (SFE) with single-step self-etch adhesives. The three single-step self-etch adhesives used were: 1) Scotchbond Universal Adhesive (3M ESPE), 2) Clearfil tri-S Bond (Kuraray Noritake Dental), and 3) G-Bond Plus (GC). Two no pre-etching groups, 1) untreated enamel and 2) enamel surfaces after ultrasonic cleaning with distilled water for 30 seconds to remove the smear layer, were prepared. There were four pre-etching groups: 1) enamel surfaces were pre-etched with phosphoric acid (Etchant, 3M ESPE) for 3 seconds, 2) enamel surfaces were pre-etched for 5 seconds, 3) enamel surfaces were pre-etched for 10 seconds, and 4) enamel surfaces were pre-etched for 15 seconds. Resin composite was bonded to the treated enamel surface to determine SBS. The SFEs of treated enamel surfaces were determined by measuring the contact angles of three test liquids. Scanning electron microscopy was used to examine the enamel surfaces and enamel-adhesive interface. The specimens with phosphoric acid pre-etching showed significantly higher SBS and SFEs than the specimens without phosphoric acid pre-etching regardless of the adhesive system used. SBS and SFEs did not increase for phosphoric acid pre-etching times over 3 seconds. There were no significant differences in SBS and SFEs between the specimens with and without a smear layer. The data suggest that phosphoric acid pre-etching of ground enamel improves the bonding performance of single-step self-etch adhesives, but these bonding properties do not increase for phosphoric acid pre-etching times over 3 seconds.

Unexpected /sup 226/Ra build-up in wet-process phosphoric-acid plants

Energy Technology Data Exchange (ETDEWEB)

Lardinoye, M.H.; Weterings, K. (Stamicarbon B.V., Geleen (Netherlands)); van de Berg, W.B. (Unie van Kunstmestfabrieken, Utrecht (Netherlands))

1982-04-01

During an investigation of the distribution of radium and uranium over the different process streams in phosphoric-acid production and in the nitrophosphate route, a higher than average radiation level was detected in the vicinity of some piping and vessels near the gypsum filters. This higher radiation level is caused by radium which is present in very low concentrations in the phosphates used for fertilizer production. Detectable radiation levels around vessels and piping in other phosphoric-acid works have since been determined. In all factories the filter part and especially the washing-acid section showed the highest radiation level. In the piping of the gypsum filter, through which the washing acid is discharged, a scaling of barium sulphate and calcium sulphate with a higher radium concentration is formed. The radium ions appeared to be incorporated in the barium sulphate lattice, hence the solubility of the radium precipitate is very low. The danger of internal contamination in cleaning operations by radioactive intake or inhalation of radon is very small in the cases described. The risk of external radiation can be prevented by periodically cleaning the equipment in which the radioactive scaling is formed.

Proton conductivity of phosphoric acid doped polybenzimidazole and its composites with inorganic proton conductors

DEFF Research Database (Denmark)

He, Ronghuan; Qingfeng, Li; Gang, Xiao

2003-01-01

Phosphoric acid doped polybenzimidazole (PBI) and PBI composite membranes have been prepared in the present work. The PBI composites contain inorganic proton conductors including zirconium phosphate (ZrP), (Zr(HPO4)2·nH2O), phosphotungstic acid (PWA), (H3PW12O40·nH2O) and silicotungstic acid (Si...

Complexity in Acid–Base Titrations: Multimer Formation Between Phosphoric Acids and Imines

Science.gov (United States)

Malm, Christian; Kim, Heejae; Wagner, Manfred

2017-01-01

Abstract Solutions of Brønsted acids with bases in aprotic solvents are not only common model systems to study the fundamentals of proton transfer pathways but are also highly relevant to Brønsted acid catalysis. Despite their importance the light nature of the proton makes characterization of acid–base aggregates challenging. Here, we track such acid–base interactions over a broad range of relative compositions between diphenyl phosphoric acid and the base quinaldine in dichloromethane, by using a combination of dielectric relaxation and NMR spectroscopy. In contrast to what one would expect for an acid–base titration, we find strong deviations from quantitative proton transfer from the acid to the base. Even for an excess of the base, multimers consisting of one base and at least two acid molecules are formed, in addition to the occurrence of proton transfer from the acid to the base and simultaneous formation of ion pairs. For equimolar mixtures such multimers constitute about one third of all intermolecular aggregates. Quantitative analysis of our results shows that the acid‐base association constant is only around six times larger than that for the acid binding to an acid‐base dimer, that is, to an already protonated base. Our findings have implications for the interpretation of previous studies of reactive intermediates in organocatalysis and provide a rationale for previously observed nonlinear effects in phosphoric acid catalysis. PMID:28597513

Corrosion rate of construction materials in hot phosphoric acid with the contribution of anodic polarization

Energy Technology Data Exchange (ETDEWEB)

Kouril, M. [Institute of Chemical Technology, Technicka 5, 166 28 Prague (Czech Republic); Christensen, E. [Technical University of Denmark, Kemitorvet, 2800 Kgs. Lyngby (Denmark); Eriksen, S.; Gillesberg, B. [Tantaline A/S, Nordborgvej 81, 6430 Nordborg (Denmark)

2012-04-15

The paper is focused on selection of a proper material for construction elements of water electrolysers, which make use of a 85% phosphoric acid as an electrolyte at temperature of 150 C and which might be loaded with anodic polarization up to 2.5 V versus a saturated Ag/AgCl electrode (SSCE). Several grades of stainless steels were tested as well as tantalum, niobium, titanium, nickel alloys and silicon carbide. The corrosion rate was evaluated by means of mass loss at free corrosion potential as well as under various levels of polarization. The only corrosion resistant material in 85% phosphoric acid at 150 C and at polarization of 2.5 V/SSCE is tantalum. In that case, even a gentle cathodic polarization is harmful in such an acidic environment. Hydrogen reduction leads to tantalum hydride formation, to loss of mechanical properties and to complete disintegration of the metal. Contrary to tantalum, titanium is free of any corrosion resistance in hot phosphoric acid. Its corrosion rate ranges from tens of millimetres to metres per year depending on temperature of the acid. Alloy bonded tantalum coating was recognized as an effective corrosion protection for both titanium and stainless steel. Its serviceability might be limited by slow dissolution of tantalum that is in order of units of mm/year. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of Phosphoric Acid Pre-etching on Fatigue Limits of Self-etching Adhesives.

Science.gov (United States)

Takamizawa, T; Barkmeier, W W; Tsujimoto, A; Scheidel, D D; Erickson, R L; Latta, M A; Miyazaki, M

2015-01-01

The purpose of this study was to use shear bond strength (SBS) and shear fatigue limit (SFL) testing to determine the effect of phosphoric acid pre-etching of enamel and dentin prior to application of self-etch adhesives for bonding resin composite to these substrates. Three self-etch adhesives--1) G- ænial Bond (GC Corporation, Tokyo, Japan); 2) OptiBond XTR (Kerr Corp, Orange, CA, USA); and 3) Scotchbond Universal (3M ESPE Dental Products, St Paul, MN, USA)--were used to bond Z100 Restorative resin composite to enamel and dentin surfaces. A stainless-steel metal ring with an inner diameter of 2.4 mm was used to bond the resin composite to flat-ground (4000 grit) tooth surfaces for determination of both SBS and SFL. Fifteen specimens each were used to determine initial SBS to human enamel/dentin, with and without pre-etching with a 35% phosphoric acid (Ultra-Etch, Ultradent Products Inc, South Jordan, UT, USA) for 15 seconds prior to the application of the adhesives. A staircase method of fatigue testing (25 specimens for each test) was then used to determine the SFL of resin composite bonded to enamel/dentin using a frequency of 10 Hz for 50,000 cycles or until failure occurred. A two-way analysis of variance and Tukey post hoc test were used for analysis of SBS data, and a modified t-test with Bonferroni correction was used for the SFL data. Scanning electron microscopy was used to examine the area of the bonded restorative/tooth interface. For all three adhesive systems, phosphoric acid pre-etching of enamel demonstrated significantly higher (padhesives clearly demonstrated different tendencies between enamel and dentin. The effect of using phosphoric acid, prior to the application of the self-etching adhesives, on SBS and SFL was dependent on the adhesive material and tooth substrate and should be carefully considered in clinical situations.

Proton conductivity of phosphoric acid doped polybenzimidazole and its composites with inorganic protontic conductors

DEFF Research Database (Denmark)

Li, Qingfeng

2003-01-01

contain inorganic protonic conductors including zirconium phosphate (ZrP), (Zr(HPO4)2. nH2O); phosphotungstic acid (PWA), (H3PW12O40. nH2O); and silicotungstic acid (SiWA), (H4SiW12O40 . nH2O). The conductivity of phosphoric acid doped PBI and PBI composite membranes was found to be dependent on the acid...

Dissociation constants of phosphoric acid in dimethylformamide-water mixtures at 298.15 K

Science.gov (United States)

Safonova, L. P.; Fadeeva, Yu. A.; Pryakhin, A. A.

2009-10-01

The dissociation constants of phosphoric acid (p K 1 and p K 2) in water-dimethylformamide (DMFA) mixtures (0-0.65 mole fractions of DMFA) were determined at 298.15 K by potentiometric titration. The extrapolation of these data to pure DMFA and the comparative calculation method were used to estimate the dissociation constants of the acid in DMFA.

Radiotracer investigation of phosphoric acid and phosphatic fertilizers production process

International Nuclear Information System (INIS)

Ben Abdelouahed, H.; Reguigui, N.

2011-01-01

In the phosphoric acid production process, the time a particle spends inside the chemical reactor (residence time) is of paramount importance to process engineers. Residence time distribution (RTD) gives information on the efficiency of the chemical reactor, on the efficiency of the process, and also the availabilities of the reactive volume for the reaction (active volume vs. dead volume). Traditionally, chemical engineers used chemical tracer to determine the RTD. However, first disadvantage is that the chemical tracer could not allow an online diagnosis: the samples containing chemical tracer have to go to a lab for analysis, second disadvantage is that the chemical tracer is less sensitive than radioactive ones because of its adsorption onto strata or its retention in rocks. Consequently, chemical tracer results are not always precise and cannot convincingly explain the multiple flow-path model. Radioactive tracers are the only tracers capable of measuring the active RTD with high degree of precision and give information on the internal recirculation rate. In this work, we will describe the application of radiotracer method for RTD measurement in the phosphoric acid production process and give results and discussion of each case encountered. (author)

Unexpected 226Ra build-up in wet-process phosphoric-acid plants.

Science.gov (United States)

Lardinoye, M H; Weterings, K; van de Berg, W B

1982-04-01

During an investigation of the distribution of radium and uranium over the different process streams in phosphoric-acid production and in the nitrophosphate route, a higher than average radiation level was detected in the vicinity of some piping and vessels near the gypsum filtres. This higher radiation level is caused by radium, which, as a decay product in the 238U series, is present in very low concentrations (1-50 pCi 226R/g) in the phosphates used for fertilizer production. Specific research later on established that there were detectable radiation levels around vessels and piping in other phosphoric-acid works as well. It turned out that in all factories the filter part, and especially the washing-acid section showed the highest radiation-level. In the piping of the gypsum filter, through which the washing acid is discharged, a scaling of bariumsulphate and calciumsulphate with a higher radiumconcentration (+/- 0.1 Ci/g) is formed. The radium ions appeared to be incorporated in the bariumsulphate lattice, hence the solubility of the radium precipitate is very low. The danger of internal pollution, for example in cleaning operations by radio-active intake or inhallation of radon is very small in the cases described. The risk of external radiation can be prevented by periodically cleaning (every 1-3 yr) the equipment in which the radio-active scaling is formed.

Effect of EDTA and phosphoric Acid pretreatment on the bonding effectiveness of self-etch adhesives to ground enamel.

Science.gov (United States)

Ibrahim, Ihab M; Elkassas, Dina W; Yousry, Mai M

2010-10-01

This in vitro study determined the effect of enamel pretreatment with phosphoric acid and ethylenediaminetetraacetic acid (EDTA) on the bond strength of strong, intermediary strong, and mild self-etching adhesive systems. Ninety sound human premolars were used. Resin composite cylinders were bonded to flat ground enamel surfaces using three self-etching adhesive systems: strong Adper Prompt L-Pop (pH=0.9-1.0), intermediary strong AdheSE (pH=1.6-1.7), and mild Frog (pH=2). Adhesive systems were applied either according to manufacturer instructions (control) or after pretreatment with either phosphoric acid or EDTA (n=10). After 24 hours, shear bond strength was tested using a universal testing machine at a cross-head speed of 0.5 mm/minute. Ultra-morphological characterization of the surface topography and resin/enamel interfaces as well as representative fractured enamel specimens were examined using scanning electron microscopy (SEM). Neither surface pretreatment statistically increased the mean shear bond strength values of either the strong or the intermediary strong self-etching adhesive systems. However, phosphoric acid pretreatment significantly increased the mean shear bond strength values of the mild self-etching adhesive system. SEM examination of enamel surface topography showed that phosphoric acid pretreatment deepened the same etching pattern of the strong and intermediary strong adhesive systems but converted the irregular etching pattern of the mild self-etching adhesive system to a regular etching pattern. SEM examination of the resin/enamel interface revealed that deepening of the etching pattern was consistent with increase in the length of resin tags. EDTA pretreatment had a negligible effect on ultra-morphological features. Use of phosphoric acid pretreatment can be beneficial with mild self-etching adhesive systems for bonding to enamel.

Studies on the interference of hydrofluoric acid and phosphoric acid in the determination of uranium using Ti(III) reduction method-biamperometry end point

International Nuclear Information System (INIS)

Shiny, T.S.; Rajalakshmi, A.; Phal, D.G.; Charyulu, M.M.; Ramakumar, K.L.

2007-01-01

Accurate and precise determination of uranium in nuclear materials is necessary for chemical quality control as well as for nuclear material accounting purposes. Different types of uranium samples are received for the measurements. Depending upon the nature of the sample dissolution procedure is selected. Mixed oxide samples of uranium and plutonium, for example, are dissolved in nitric acid containing hydrofluoric acid under IR lamp. The fluoride ions are removed by repeated evaporation of the solution. However, some fluoride ions are left in the solutions depending on the conditions of evaporation. Uranium samples and alloy samples are dissolved in dilute hydrochloric acid. The rate of dissolution depends on concentration of acid. Sometimes a mixture of hydrochloric acid and hydrofluoric acid is used for the dissolution metal alloy samples, which may contain silica. Another method of dissolution of these samples is using a mixture of phosphoric acid and 1% hydrofluoric acid. It is necessary to study the interference of hydrofluoric acid and phosphoric acid on the determination of uranium

Preparation and Characterization of Various Activated Carbons Derived From Mixed Precursors Using Phosphoric Acid

International Nuclear Information System (INIS)

Daifullah, A.A.M.; Sharaf El-Deen, S.E.A.; Elkhalafawy, A.; Shehata, F.A.; Mahmoud, W.H.

2008-01-01

Rice straw (RS) and rice husk (RH), a low-cost agricultural by-products, have been used as a mixed precursor (i.e., RS mixed with RH in 1:1; 1:3 and 3:1 ratios) for the production of novel carbons using phosphoric acid as chemical activation. The raw materials were impregnated with 50% and 70% H 3 PO 4 followed by activation at 500 degree C. The latter proved to be the most effective in producing active carbon with good adsorptive capacity. The resulting carbons were characterized by elemental analysis, infrared spectroscopy, density, SEM and S BET . In general, the resulting carbons showed reasonable surface areas with mainly micropore structure. The adsorption capacity was demonstrated by the isotherms of methylene blue (MB), phenol and iodine from aqueous solution. The adsorption data was found to conform with the Langmuir equation with the concentration range studied, and the monolayer coverage was determined for each of the samples. It was found that surface area is mainly attributed to micropore volume so that phenol adsorption and iodine number correspond well with surface area determined by nitrogen adsorption

Optimization of cellulose nanocrystal length and surface charge density through phosphoric acid hydrolysis

Science.gov (United States)

Vanderfleet, Oriana M.; Osorio, Daniel A.; Cranston, Emily D.

2017-12-01

Cellulose nanocrystals (CNCs) are emerging nanomaterials with a large range of potential applications. CNCs are typically produced through acid hydrolysis with sulfuric acid; however, phosphoric acid has the advantage of generating CNCs with higher thermal stability. This paper presents a design of experiments approach to optimize the hydrolysis of CNCs from cotton with phosphoric acid. Hydrolysis time, temperature and acid concentration were varied across nine experiments and a linear least-squares regression analysis was applied to understand the effects of these parameters on CNC properties. In all but one case, rod-shaped nanoparticles with a high degree of crystallinity and thermal stability were produced. A statistical model was generated to predict CNC length, and trends in phosphate content and zeta potential were elucidated. The CNC length could be tuned over a relatively large range (238-475 nm) and the polydispersity could be narrowed most effectively by increasing the hydrolysis temperature and acid concentration. The CNC phosphate content was most affected by hydrolysis temperature and time; however, the charge density and colloidal stability were considered low compared with sulfuric acid hydrolysed CNCs. This study provides insight into weak acid hydrolysis and proposes `design rules' for CNCs with improved size uniformity and charge density. This article is part of a discussion meeting issue `New horizons for cellulose nanotechnology'.

Physical-Mechanical Properties and Micromorphology of Calcium Cements Exposed to Polyacrylic and Phosphoric Acids.

Science.gov (United States)

de Souza, Gustavo Fernandes; Arrais, Ana Beatriz; Aragão, Cícero Flávio Soares; Ferreira, Isana Alvares; Borges, Boniek Castillo Dutra

2018-01-01

To evaluate if physical and mechanical properties of self-curing calcium hydroxide cements were affected by contact with polyacrylic and phosphoric acids. Resin-containing (Life (LF)) and resin-free (Hydro C (HyC)) materials were subjected to polyacrylic acid conditioning and rinsing (POL); phosphoric acid conditioning and rinsing (PHO); rinsing only; and no treatment ( n = 10). Water sorption/solubility, release of hydroxyl ions (pH), roughness (Ra), and impact resistance were evaluated. Additional samples ( n = 1) were prepared for scanning electron microscopy (SEM) analysis of the surface morphology. Data were analyzed by two-way ANOVA and Tukey post hoc test ( P < 0.05). Water sorption was significantly higher for LF when in contact with PHO and lower for POL ( P < 0.05). The mean solubility was higher with POL for both cements ( P < 0.05). PHO increased the mean surface roughness for HyC ( P < 0.01); a significant decrease was noted for LF after contact with both acids ( P < 0.01). PHO promoted lower release of hydroxyl ions on both cements ( P < 0.05). For LF, rinsing, PHO, and POL presented similar morphology, differing from the control group. For HyC, PHO and POL presented similar morphology, differing from the control group. PHO had a negative effect on the physical properties of the cements tested, except for the solubility test. POL affected roughness and solubility of HyC cement. Clinical procedures that require polyacrylic and phosphoric acid conditioning must be done carefully on self-curing calcium hydroxide cements in order to avoid negative impact on their properties.

The derivative-free Fourier shell identity for photoacoustics.

Science.gov (United States)

Baddour, Natalie

2016-01-01

In X-ray tomography, the Fourier slice theorem provides a relationship between the Fourier components of the object being imaged and the measured projection data. The Fourier slice theorem is the basis for X-ray Fourier-based tomographic inversion techniques. A similar relationship, referred to as the 'Fourier shell identity' has been previously derived for photoacoustic applications. However, this identity relates the pressure wavefield data function and its normal derivative measured on an arbitrary enclosing aperture to the three-dimensional Fourier transform of the enclosed object evaluated on a sphere. Since the normal derivative of pressure is not normally measured, the applicability of the formulation is limited in this form. In this paper, alternative derivations of the Fourier shell identity in 1D, 2D polar and 3D spherical polar coordinates are presented. The presented formulations do not require the normal derivative of pressure, thereby lending the formulas directly adaptable for Fourier based absorber reconstructions.

Study of shrimp shell derivatives for treating of low-level radioactive liquid wastes

Energy Technology Data Exchange (ETDEWEB)

Hayeripour, S. [Tonkabon Islamic Azad Univ., Tonkabon (Iran, Islamic Republic of). College of the Environment; Malmasi, S. [North Tehran Islamic Azad Univ., Tehran (Iran, Islamic Republic of). College of the Environment

2006-07-01

Chitin derivatives can be used to treat liquid wastes that include heavy metals of radionuclides. In this study, 4 types of chitin derivatives from shrimp shell waste were investigated for their potential in decontaminating and treating low-level radioactive liquid waste (LLW). The adsorption of caesium (Cs); cobalt (Co); and manganese (Mn) isotopes on chitin derivatives were investigated using a batch and column system with variations in diameter, pH, and length of treatment. Chitin derivatives included shrimp shells; de-mineralized shrimp shells; chitin extracted from shrimp shells; and chitosan extracted from shrimp shell waste. Three types of simulated solutions were prepared to study and compare adsorption performance: (1) a mono cationic solution consisting of stable isotopes; (2) a solution containing 3 stable cations; and (3) a simulated radioactive waste containing Cs-137, Co-60, and Mn-54. Results of the experiments showed that all 4 chitin derivatives were capable of adsorbing the isotopes. Despite its low pH, chitosan showed the highest adsorption efficiency. It was concluded that shrimps shells provided unreliable results under different operating conditions. The demineralized shells were suitable for removing Co from solutions. Row shells were not recommended as a suitable adsorbent for radionuclides removal. 14 refs., 2 tabs., 6 figs.

Feasibility studies on supercritical fluid extraction of uranium from phosphoric acid

International Nuclear Information System (INIS)

Dubey, B.P.; Agarwal, A.K.

2014-01-01

Supercritical fluid extraction (SFE) is a promising novel technology for extraction of many materials. Work has been carried out worldwide on SFE of uranium from various matrices. However, there are no references indicating the R and D on uranium extraction from phosphoric acid using this technology. Heavy Water Board is involved in technology development for recovery of uranium from secondary source, hence it was considered prudent to investigate the technology of SFE for this purpose. Various experiments were carried out with both WPA (P 2 O 5 content 28%) and MGPA (P 2 O 5 content 54%) using bench scale facility available with one of the private party. Extraction experiments were carried out using several chelating agents including TBP, D2EHPA, D2EHPA+TBP/TOPO, TTA, TTA+TBP etc. Feasibility studies revealed the hydrodynamics of operation indicating liquid expansion by about three times during flow of super critical (SC) CO 2 . No flooding was observed when the extraction column filled 20% of its volume capacity, no carryover of entrained/extracted liquid with SC CO 2 with MGPA, material balance of inputs and outputs established i.e. 100% recovery of MGPA and chelating agent, No operational problems with raw MGPA (untreated). No significant extraction of impurities from phosphoric acid to SC CO 2 , 40℃ temperature and 160 bar pressure found ideal for extraction experiments since no other materials found extracted at these conditions and no apparent change/deterioration in PA and chelating agents. Experiments established feasibility of SCE with CO 2 , proper recovery of PA and chelating agents, no need for pretreatment/gunk removal from PA; however, extraction of uranium was found inadequate even though ORP of feed acid was boosted by H 2 O 2 addition. Investigations revealed that SCE column created reducing environment in phosphoric acid, which was not favourable for uranium extraction, which resulted in difficulty in extraction of Uranium. HWB has now designed

Methyl phosphate formation as a major degradation mode of direct methanol fuel cells with phosphoric acid based electrolytes

DEFF Research Database (Denmark)

Aili, David; Vassiliev, Anton; Jensen, Jens Oluf

2015-01-01

Phosphoric acid and phosphoric acid doped polymer membranes are widely used as electrolytes in hydrogen based fuel cells operating at elevated temperatures. Such electrolytes have been explored for direct oxidation of methanol to further increase the versatility of the systems, however......, with demonstrated lifetimes of only a few days to weeks. In this work the methyl phosphate formation from the acid and methanol is identified and proposed to be a major mechanism for the cell degradation. Proton conductivity and fuel cell durability tests validate the mechanism at high methanol contents....

Systematically controlled pore system of ordered mesoporous carbons using phosphoric acid as the in situ generated catalysts for carbonization and activation

Energy Technology Data Exchange (ETDEWEB)

Jin, Xing; Lee, Chang Hyun; Kim, Jin Hoe; You, Dae Jong; Shon, Jeong Kuk; Kim, Ji Man [Dept. of Chemistry, Sungkyunkwan University, Suwon (Korea, Republic of); Pak, Chan Ho [Fuel Cell Group, Corporate R and D Center, Samsung SDI Co. Ltd., Yongin (Korea, Republic of)

2015-08-15

We report on a facile synthesis of the ordered mesoporous carbon (OMC) materials with systematically controlled microporosity and mesoporosity simultaneously through the nano-replication route using phosphoric acid as the acid catalyst and activation agent. The use of phosphoric acid affects the pore structures of OMC materials, such as the formation of numerous micropores by activation of the carbon framework and the enlargement of mesopores by spontaneous phase separation during the carbonization. The mesopore sizes, surface areas, total pore volumes, and micropore volumes of the OMC materials are highly dependent on the phosphoric acid content and can be systematically controlled in the range 3.7–7.5 nm, 1027–2782 m{sup 2} g{sup -1}, 1.12–3.53 cm{sup 3} g{sup -1} and 0.34–0.95 cm{sup 3} g{sup -1}, respectively. OMC materials with systematically controlled pore structures were successfully synthesized using phosphoric acid as the carbonization catalyst and mesoporous silica materials with cubic Ia3d and 2-D hexagonal mesostructures as the templates. The phosphoric acid in the synthesis of ordered mesoporous carbon materials acts as the chemical activating agent for micropore generation of the carbon framework and pore-expanding agent for controlling of mesopore size, in addition to functioning as the acid catalyst. The present synthesis pathway is very useful for preparing OMC materials with tunable mesopore sizes and well-developed microporosities at the same time.

Preparation and physical properties of (PVA0.7(NaBr0.3(H3PO4xM solid acid membrane for phosphoric acid – Fuel cells

Directory of Open Access Journals (Sweden)

F. Ahmad

2013-03-01

Full Text Available A solid acid membranes based on poly (vinyl alcohol (PVA, sodium bromide (NaBr and phosphoric acid (H3PO4 were prepared by a solution casting method. The morphological, IR, electrical and optical properties of the (PVA0.7(NaBr0.3(H3PO4xM solid acid membranes where x = 0.00, 0.85, 1.7, 3.4, 5.1 M were investigated. The variation of film morphology was examined by scanning electron microscopy (SEM studies. FTIR spectroscopy has been used to characterize the structure of polymer and confirms the complexation of phosphoric acid with host polymeric matrix. The temperature dependent nature of ionic conductivity and the impedance of the polymer electrolytes were determined along with the associated activation energy. The ionic conductivity at room temperature was found to be strongly depends on the H3PO4 concentration which it has been achieved to be of the order 4.3 × 10−3 S/cm at ambient temperature. Optical measurements showed a decrease in optical band gap and an increase in band tail width with the increase of phosphoric acid. The data shows that the (PVA0.7(NaBr0.3(H3PO4xM solid acid membrane is promising for intermediate temperature phosphoric acid fuel cell applications.

Search for a developed method for the determination of Fe2 and Fe3 in Syrian Phosphoric acid

International Nuclear Information System (INIS)

Elian, Nuzhat; Kalak, Issam

1988-08-01

Phosphoric acid is the most important precursor for uranium production in Syria. Uranium extraction from phosphoric acid depends on the chemical composition of the acid, and most important is the relation between the proportions of iron I I/iron I II, and uranium I V/uranium V I, this proportion plays a very important role in different steps of the extraction. For this purposes two methods for determination of Iron I I and Iron I II in Syrian wet phosphoric acid spectrophotometrically were studied. The first one used 1.10 phenanthroline as complex agent. Iron I I formed red complex with 1.10 phenonstholine in the range of pH between 4 and 6, for determination of total iron. Iron I II was reduced to Iron I I with hydroxylamine hydrochloride. The second method used sulfosalycilic acid, Iron I II formed a yellow complex with sulfosalycilic acid. Total iron was determined in ammonium medium, but Iron I II was determined in pH=1.5. The sensibility of the tow methods and stability of their complex have been studied in normal laboratory conditions. 45 refs., 4 figs. (author)

Survey on aging on electrodes and electrocatalysts in phosphoric acid fuel cells

Science.gov (United States)

Stonehart, P.; Hochmuth, J.

1981-01-01

The processes which contribute to the decay in performance of electrodes used in phosphoric acid fuel cell systems are discussed. Loss of catalytic surface area, corrosion of the carbon support, electrode structure degradation, electrolyte degradation, and impurities in the reactant streams are identified as the major areas for concern.

Measurement of the oxidation-extraction of uranium from wet-process phosphoric acid

International Nuclear Information System (INIS)

Lawes, B.C.

1985-01-01

The present invention relates to processes for the recovery of uranium from wet-process phosphoric acid and more particularly to the oxidation-extraction steps in the DEPA-TOPO process for such recovery. A more efficient use of oxidant is obtained by monitoring the redox potential during the extraction step

Separation of uranium and other metals from commercial phosphoric acid by ion-exchange and voltammetric determination of uranium

International Nuclear Information System (INIS)

Ferreira, J.B.C.; Carvalho, F.M.S. de; Abrao, A.

1985-11-01

The separation of metals from crude commercial phosphoric acid is achieved by simple dilution and percolation through a strong cationic ion exchanger. Uranium, calcium, magnesium, manganese, iron and aluminum are quantitatively fixed by the exchanger and can be detected or analysed after their complete elution with 6 M HCI. Titanium and zirconium are only partially retained. Specially for its separation and determination uranium is retained selectively by the resin from the phosphoric acid-EDTA solution, the column is washed with water and then eluted with hydrochloric acid. Uranium is analyzed by voltametry with the hanging drop mercury electrode. (Author) [pt

Evaluation of human dental loss caused by carbamide peroxide bleacher compared with phosphoric acid conditioning - radioactive method

International Nuclear Information System (INIS)

Adachi, Eduardo Makoto; Yousseff, Michel Nicolau; Saiki, Mitiko

2002-01-01

The radiometric method was applied to the evaluation of dental loss caused by carbamide peroxide when it is applied on the surface layers of enamel and dentin tissues. Also the dental loss caused by the etching with 37% phosphoric acid procedure used in aesthetic restoration was assessed for comparison with those results obtained. The tooth samples irradiated with a P standard in a thermal neutron flux of the nuclear reactor were placed in contact with 10% carbamide peroxide or with 37% phosphoric acid solution. The radioactivity of 32 P transferred from the radioactive teeth to the bleaching gel or to etching acid was measured using a Geiger Muller detector to calculate the mass of P removed in this treatment and losses were calculated after obtaining their P concentrations. Results obtained indicated that enamel and dentin exposed to carbamide peroxide bleaching agent lose phosphorus. The extent of enamel loss was smaller than that obtained for dentin. In the case of acid etching, there was no difference between the results obtained for enamel and dentin loss. Also the dentin loss obtained after a treatment of 30 applications of 10% carbamide peroxide was the same magnitude of that one application of 37% phosphoric acid. (author)

Furfural production from fruit shells by acid-catalyzed hydrolysis

Energy Technology Data Exchange (ETDEWEB)

Demirbas, A. [Selcuk Univ., Konya (Turkey). Dept. of Chemical Engineering

2006-01-21

Pentosans are hydrolyzed to pentoses by dilute mineral acid hydrolysis. The main source of pentosans is hemicelluloses. Furfural can be produced by the acid hydrolysis of pentosan from fruit shells such as hazelnut, sunflower, walnut, and almond of agricultural wastes. Further dehydration reactions of the pentoses yield furfural. The hydrolysis of each shell sample was carried out in dilute sulfuric acid (0.05 to 0.200 mol/l), at high temperature (450-525 K), and short reaction times (from 30 to 600 s). (author)

Multi-shell model of ion-induced nucleic acid condensation

Energy Technology Data Exchange (ETDEWEB)

Tolokh, Igor S. [Department of Computer Science, Virginia Tech, Blacksburg, Virginia 24061 (United States); Drozdetski, Aleksander V. [Department of Physics, Virginia Tech, Blacksburg, Virginia 24061 (United States); Pollack, Lois [School of Applied and Engineering Physics, Cornell University, Ithaca, New York 14853-3501 (United States); Baker, Nathan A. [Advanced Computing, Mathematics, and Data Division, Pacific Northwest National Laboratory, Richland, Washington 99352 (United States); Division of Applied Mathematics, Brown University, Providence, Rhode Island 02912 (United States); Onufriev, Alexey V. [Department of Computer Science, Virginia Tech, Blacksburg, Virginia 24061 (United States); Department of Physics, Virginia Tech, Blacksburg, Virginia 24061 (United States)

2016-04-21

We present a semi-quantitative model of condensation of short nucleic acid (NA) duplexes induced by trivalent cobalt(III) hexammine (CoHex) ions. The model is based on partitioning of bound counterion distribution around single NA duplex into “external” and “internal” ion binding shells distinguished by the proximity to duplex helical axis. In the aggregated phase the shells overlap, which leads to significantly increased attraction of CoHex ions in these overlaps with the neighboring duplexes. The duplex aggregation free energy is decomposed into attractive and repulsive components in such a way that they can be represented by simple analytical expressions with parameters derived from molecular dynamic simulations and numerical solutions of Poisson equation. The attractive term depends on the fractions of bound ions in the overlapping shells and affinity of CoHex to the “external” shell of nearly neutralized duplex. The repulsive components of the free energy are duplex configurational entropy loss upon the aggregation and the electrostatic repulsion of the duplexes that remains after neutralization by bound CoHex ions. The estimates of the aggregation free energy are consistent with the experimental range of NA duplex condensation propensities, including the unusually poor condensation of RNA structures and subtle sequence effects upon DNA condensation. The model predicts that, in contrast to DNA, RNA duplexes may condense into tighter packed aggregates with a higher degree of duplex neutralization. An appreciable CoHex mediated RNA-RNA attraction requires closer inter-duplex separation to engage CoHex ions (bound mostly in the “internal” shell of RNA) into short-range attractive interactions. The model also predicts that longer NA fragments will condense more readily than shorter ones. The ability of this model to explain experimentally observed trends in NA condensation lends support to proposed NA condensation picture based on the multivalent �

Process for recovering uranium from wet process phosphoric acid (III)

International Nuclear Information System (INIS)

Pyrih, R.Z.; Rickard, R.S.; Carrington, O.F.

1983-01-01

Uranium is conventionally recovered from wet-process phosphoric acid by two liquid ion exchange steps using a mixture of mono- and disubstituted phenyl esters of orthophosphoric acid (OPPA). Efficiency of the process drops as the mono-OPPA is lost preferentially to the aqueous phase. This invention provides a process for the removal of the uranium process organics (OPPA and organic solvents) from the raffinate of the first liquid ion exchange step and their return to the circuit. The process organics are removed by a combination flotation and absorption step, which results in the recovery of the organics on beads of a hydrophobic styrene polymer

Geochemistry of amino acids in shells of the clam Saxidomus

Science.gov (United States)

Kvenvolden, K.A.; Blunt, D.J.; McMenamin, M.A.; Straham, S.E.

1980-01-01

Concentrations of amino acids and their corresponding d l enantiomeric ratios have been measured in shells of the bivalve mollusk Saxidomus from eleven localities, ranging in age from modern to probably more than 500,000 yr, along the Pacific coast of North America. Natural logarithms of amino acid concentrations correlate well with d l ratios, and the relationship provides a possible guide to the selection of fossils for use in amino acid dating. The relative order of the extents of racemization of amino acids at any given time appears to change with increasing sample age. Application of the amino acid dating method to shells from Whidbey Island, Washington, yields an age of about 80,000 yr, in contrast to the previously determined radiocarbon age of 36,000 yr which was measured on some shell carbonate and considered a minimum age. The amino acid age is compatible with the geologic record in the area. ?? 1980.

Spectrophotometric Analysis of Phosphoric Acid Leakage in High-Temperature Phosphoric Acid-Doped Polybenzimidazole Membrane Fuel Cell Application

Directory of Open Access Journals (Sweden)

Seungyoon Han

2016-01-01

Full Text Available High-temperature proton exchange membrane fuel cells (HT-PEMFCs utilize a phosphoric acid- (PA- doped polybenzimidazole (PBI membrane as a polymer electrolyte. The PA concentration in the membrane can affect fuel cell performance, as a significant amount of PA can leak from the membrane electrode assembly (MEA by dissolution in discharged water, which is a byproduct of cell operation. Spectrophotometric analysis of PA leakage in PA-doped polybenzimidazole membrane fuel cells is described here. This spectrophotometric analysis is based on measurement of absorption of an ion pair formed by phosphomolybdic anions and the cationoid color reagent. Different color reagents were tested based on PA detection sensitivity, stability of the formed color, and accuracy with respect to the amount of PA measured. This method allows for nondestructive analysis and monitoring of PA leakage during HT-PEMFCs operation.

Unexpected /sup 226/Ra build-up in wet-process phosphoric-acid plants

Energy Technology Data Exchange (ETDEWEB)

Lardinoye, M.H.; Weterings, K.; van de Berg, W.B.

1982-04-01

During an investigation of the distribution of radium and uranium over the different process streams in phosphoric-acid production and in the nitrophosphate route, a higher than average radiation level was detected in the vicinity of some piping and vessels near the gypsum filtres. This higher radiation level is caused by radium, which, as a decay product in the /sup 238/U series, is present in very low concentrations (1-50 pCi 226R/g) in the phosphates used for fertilizer production. Specific research later on established that there were detectable radiation levels around vessels and piping in other phosphoric-acid works as well. It turned out that in all factories the filter part, and especially the washing-acid section showed the highest radiation-level. In the piping of the gypsum filter, through which the washing acid is discharged, a scaling of bariumsulfate and calciumsulfate with a higher radium concentration (+/- 0.1 Ci/g) is formed. The radium ions appeared to be incorporated in the bariumsulphate lattice, hence the solubility of the radium precipitate is very low. The danger of internal pollution, for example in cleaning operations by radioactive intake or inhalation of radon is very small in the cases described. The risk of external radiation can be prevented by periodically cleaning (every 1-3 yr) the equipment in which the radioactive scaling is formed.

Phosphoric acid doped polysulfone membranes with aminopyridine pendant groups and imidazole cross-links

DEFF Research Database (Denmark)

Hink, Steffen; Elsøe, Katrine; Cleemann, Lars Nilausen

2015-01-01

Udel polysulfone based membranes with 4-aminopyridine pendant groups and cross-linking imidazole units are synthesized in a simple two step reaction. The ratio of 4-aminopyridine and imidazole is varied and the materials are extensively characterized. The average phosphoric acid uptake (in 85 wt%...

Catalyst evaluation for oxygen reduction reaction in concentrated phosphoric acid at elevated temperatures

DEFF Research Database (Denmark)

Hu, Yang; Jiang, Yiliang; Jensen, Jens Oluf

2018-01-01

Phosphoric acid is the common electrolyte for high-temperature polymer electrolyte fuel cells (HT-PEMFCs) that have advantages such as enhanced CO tolerance and simplified heat and water management. The currently used rotating disk electrode technique is limited to tests in dilute solutions at lo...

Phosphors for LED lamps

Science.gov (United States)

Murphy, James Edward; Manepalli, Satya Kishore; Kumar, Prasanth Nammalwar

2013-08-13

A phosphor, a phosphor blend including the phosphor, a phosphor prepared by a process, and a lighting apparatus including the phosphor blend are disclosed. The phosphor has the formula (Ca.sub.1-p-qCe.sub.pK.sub.q).sub.xSc.sub.y(Si.sub.1-rGa.sub.r).sub.zO.su- b.12+.delta. or derived from a process followed using disclosed amounts of reactants. In the formula, (0

Impact of pH and application time of meta-phosphoric acid on resin-enamel and resin-dentin bonding.

Science.gov (United States)

Cardenas, A F M; Siqueira, F S F; Bandeca, M C; Costa, S O; Lemos, M V S; Feitora, V P; Reis, A; Loguercio, A D; Gomes, J C

2018-02-01

To evaluate the immediate microshear resin-enamel bond strength (μSBS) and the immediate and 6-month microtensile bond strength (μTBS) and nanoleakage (NL) of the adhesive interface performed by different pHs of 40% meta-phosphoric acid (MPA) were compared with conventional 37% ortho-phosphoric acid (OPA) under different application times. Additionally, the enamel etching patterns were evaluated and the chemical/morphological changes induced by these differents groups were evaluated. One hundred and ninety-eight extracted human molars were randomly assigned into experimental groups according to the combination of independent variables: Acid [37% ortho-phosphoric acid (OPA), 40% meta-phosphoric acid (MPA) at pHs of: 0.5, 1 and 2] and Application Time [7, 15 and 30s]. Enamel-bond specimens were prepared and tested under μSBS. Resin-dentin beams were tested under μTBS tested immediately or after 6-months of water storage. Nanoleakage was evaluated using bonded-beams of each tooth/time-period. Enamel etching pattern and chemical and ultra-morphology analyses were also performed. The μSBS (MPa) data were subjected to a two-way repeated measures ANOVA (Acid vs. Application time). For μTBS, Acid vs application time vs storage time data were subjected to three-way ANOVA and Tukey's test (α = 0.05). MPA pH 0.5 showed μTBS similar to OPA, independently of the application time on enamel (p>0.05) or dentin (p>0.05). OPA provided higher nanoleakage values than MPA (p = 0.003). Significant decreases in TBS and increases in NL were only observed for OPA after 6 months (p = 0.001). An increase in the application time resulted in a more pronounced etching pattern for MPA. Chemical analysis showed that dentin demineralized by MPA depicted peaks of brushite and octacalcium phosphate. MPA exposed less collagen than OPA. However, optimal results for MPA were dependent on pH/application time. The use of 40% meta-phosphoric acid with a pH of 0.5 is an alternative acid

Catalyst evaluation for oxygen reduction reaction in concentrated phosphoric acid at elevated temperatures

Science.gov (United States)

Hu, Yang; Jiang, Yiliang; Jensen, Jens Oluf; Cleemann, Lars N.; Li, Qingfeng

2018-01-01

Phosphoric acid is the common electrolyte for high-temperature polymer electrolyte fuel cells (HT-PEMFCs) that have advantages such as enhanced CO tolerance and simplified heat and water management. The currently used rotating disk electrode technique is limited to tests in dilute solutions at low temperatures and hence is not suitable for catalyst evaluation for HT-PEMFCs. In this study, we have designed and constructed a half-cell setup to measure the intrinsic activities of catalysts towards the oxygen reduction reaction (ORR) in conditions close to HT-PEMFC cathodes. By optimization of the hydrophobic characteristics of electrodes and the catalyst layer thickness, ORR activities of typical Pt/C catalysts are successfully measured in concentrated phosphoric acid at temperatures above 100 °C. In terms of mass-specific activities, the catalyst exhibits about two times higher activity in the half-cell electrode than that observed in fuel cells, indicating the feasibility of the technique as well as the potential for further improvement of fuel cell electrode performance.

The Comparison of Hydrochloric Acid and Phosphoric Acid Treatments in the Preparation of Montmorillonite Catalysts for RNA Synthesis

Science.gov (United States)

Aldersley, Michael Frank; Joshi, Prakash C.; Huang, Yixing

2017-09-01

The treatment of clay minerals with a preliminary acid wash and titration to pH 7 has proven to generate catalysts for the most interesting of oligomerization reactions in which activated RNA-nucleotides generate oligomers up to 40-mers. Significantly, not all clay minerals become catalytic following this treatment and none are catalytic in the absence of such treatment. The washing procedure has been modified and explored further using phosphoric acid and the outcomes are compared to those obtained when clay samples are prepared following a hydrochloric acid wash.

Influence of anodization parameters on the volume expansion of anodic aluminum oxide formed in mixed solution of phosphoric and oxalic acids

Science.gov (United States)

Kao, Tzung-Ta; Chang, Yao-Chung

2014-01-01

The growth of anodic alumina oxide was conducted in the mixed solution of phosphoric and oxalic acids. The influence of anodizing voltage, electrolyte temperature, and concentration of phosphoric and oxalic acids on the volume expansion of anodic aluminum oxide has been investigated. Either anodizing parameter is chosen to its full extent of range that allows the anodization process to be conducted without electric breakdown and to explore the highest possible volume expansion factor. The volume expansion factors were found to vary between 1.25 and 1.9 depending on the anodizing parameters. The variation is explained in connection with electric field, ion transport number, temperature effect, concentration, and activity of acids. The formation of anodic porous alumina at anodizing voltage 160 V in 1.1 M phosphoric acid mixed with 0.14 M oxalic acid at 2 °C showed the peak volume expansion factor of 1.9 and the corresponding moderate growth rate of 168 nm/min.

Phosphoric acid doped imidazolium polysulfone membranes for high temperature proton exchange membrane fuel cells

DEFF Research Database (Denmark)

Yang, Jingshuai; Li, Qingfeng; Jensen, Jens Oluf

2012-01-01

A novel acid–base polymer membrane is prepared by doping of imidazolium polysulfone with phosphoric acid for high temperature proton exchange membrane fuel cells. Polysulfone is first chloromethylated, followed by functionalization of the chloromethylated polysulfone with alkyl imidazoles i.e. me...

A contribution to the study of mass transfer: uranium extraction from phosphoric acid

International Nuclear Information System (INIS)

Maher, A.

1985-12-01

Liquid-liquid extraction of uranium (VI) contained in phosphoric acid is examined. Synergism and thermodynamical equilibria are studied. Influence of drop size, extractant concentration and temperature on reaction kinetics are determined. The experimental study concerns extraction by HDEHP, TOPO and the mixture of both. Reaction mechanisms are interpreted [fr

Interfacial characteristics of an epoxy composite reinforced with phosphoric acid-functionalized Kevlar fibers

Science.gov (United States)

Li, J.; Xia, Y. C.

2010-07-01

A Kevlar fiber was functionalized with the phosphoric acid (PA) of different concentrations. The surface characteristics of the fiber were examined by using the X-ray photoelectron spectroscopy. It was found that the PA functionalization considerably increased the bond strength between the Kevlar fiber and an epoxy matrix.

Extraction of uranium from wet process phosphoric acid in centrifugal and mixer-settler batteries

International Nuclear Information System (INIS)

Poczynajlo, A.; Giers, M.

1986-01-01

Five stage countercurrent batteries were comparatively applied for the extraction of uranium from wet phosphoric acid (Chemical Works, Police) in semitechnical scale. As an extractant phase the 0.16 M equimolar solution of mono- and dinonylphenyolphosphoric acids in kerosene was used. The optimum hydrodynamic and extraction conditions for the batteries were found. Process efficiencies of the apparatus were also determined. 5 refs., 5 figs., 2 tabs. (author)

Polymeric supported sorbents for decreasing hazardous metal ions content in wet process phosphoric acid

International Nuclear Information System (INIS)

El-Zahhar, A.A.; El-Naggar, H.A.; Ahmed, M.

2005-01-01

Procedure for preparation of polymeric supported silica, and their usage for decreasing hazardous metal ion content in wet process phosphoric acid was developed. The procedure is based firstly on extraction silica from rice straw by alkaline treatment , secondly supporting the produced silica on binding polyacrylonitrile (PAN). The produced polymer based sorbent was used for decreasing hazardous metal ions (especially iron) present as inorganic impurities in crud Egyptian phosphoric acid (green acid). Different factors affecting the sorption equilibrium ( contact time, temperature , sorbent mass and batch factor ) were studied. Studying the sorption isotherm revealed that the adsorption data could favorably fit the Langmuir adsorption isotherm. In the dynamic study , the sorption capacity at (Cξ/Cο = 50%) was found to be 28.5 mg/g and the loaded column could be regenerated using 50ml of 0.15 M HNO 3 . The regenerated column could undergo sorption regeneration cycles up to four cycles without significant decrease in the sorption capacity , weight loss or change in the physical properties of the sorbent

Manual of phosphoric acid fuel cell power plant cost model and computer program

Science.gov (United States)

Lu, C. Y.; Alkasab, K. A.

1984-01-01

Cost analysis of phosphoric acid fuel cell power plant includes two parts: a method for estimation of system capital costs, and an economic analysis which determines the levelized annual cost of operating the system used in the capital cost estimation. A FORTRAN computer has been developed for this cost analysis.

Liquid-liquid extraction of uranium from Egyptian phosphoric acid using a synergistic D2EHPA-DBBP mixture

International Nuclear Information System (INIS)

Abdel-Khalek, A.A.

2011-01-01

Extraction of uranium from Egyptian phosphoric acid with synergistic mixture of di-2-ethylhexylphosphoric acid (D2EHPA) and di-butyl butyl phosphonate (DBBP) is reported in this paper. The influence of various factors such as D2EHPA concentration, DBBP concentration, phosphoric acid concentration, contact time, aqueous: organic phase's ratio (aq:org) and temperature on the degree of extraction has been established. The data on the effect of temperature on the extraction showed that the enthalpy change is -23.12 kJ/mol. Uranium extracted by D2EHPA- DBBP is further subjected to a second cycle of extraction and scrubbing impurities. The uranium is finally converted to a high purity UO 3 product using precipitation with hydrogen peroxide and heat treatment at 375 deg C. (author)

On the fractionation of natural radioactivity in the production of phosphoric acid by the wet acid method

International Nuclear Information System (INIS)

Bolivar, J.P.; Garcia-Tenorio, R.; Garcia-Leon, M.

1996-01-01

The fractionation of different natural radionuclides (U-isotopes, 226 Ra and 210 Po) in the process used for the production of phosphoric acid in some factories located in the south-west of Spain is analyzed. As a consequence, different ways of natural radionuclide liberation to the environment can be evaluated due to these industrial activities. (author). 9 refs., 2 figs., 3 tabs

Passivation behaviour of stainless steel (UNS N-08028) in industrial or simplified phosphoric acid solutions at different temperatures

International Nuclear Information System (INIS)

Ben Salah, M.; Sabot, R.; Refait, Ph.; Liascukiene, I.; Méthivier, C.; Landoulsi, J.; Dhouibi, L.

2015-01-01

Highlights: • Industrial phosphoric acid is less aggressive than simulated industrial acid. • Polyphosphate film in Industrial acid is reinforced by calcium and sulfate. • Passive film thickness is obtained by the power law model from EIS measurements. • Passive film of Sanicro28 becomes more resistive towards corrosion with exposure time in industrial acid. • XPS measurements coupled to Raman spectroscopy reveal the corrosion products formed in simulated acid. - Abstract: The corrosion behaviour of Sanicro28, in industrial phosphoric acid and simplified solution of pure H_3PO_4 containing sulphates and chlorides, is investigated during 48 h between 20 and 80 °C. Results show higher corrosion resistance in the industrial medium. Film thickness evaluated by EIS remains constant in industrial acid due to polyphosphate that promotes crystallisation of the Cr_2O_3 inner layer. Conversely, the passive film is partially destroyed at 80 °C in simplified acid. XPS and Raman analysis show that phosphate and molybdenum are both present in the passive film and in corrosion products. The role of Ca present in the industrial acid is discussed.

Production of activated carbon from peanut hill using phosphoric acid and microwave activation

Directory of Open Access Journals (Sweden)

Weerawat Clowutimon

2015-06-01

Full Text Available The optimum conditions for preparing activated carbon from peanut hulls by phosphoric acid and microwave activation were studied. Factors investigated in this study were temperature of carbonization at 300, 350, 400 and 450๐ C, and time of carbonization at 30, 60 and 90 minutes. The optimum yield was observed that carbonization temperature of 400๐ C and time at 60 minutes, respectively. The yield of charcoal was 39% and the f ix carbon was 69%. Then the charcoal was activated by phosphoric acid and microwave irradiation, respectively. The effect of the weight per volume ratios of charcoal to activating acid (1:1, 1:2 and 2:1(W/V, microwave power at (activated 300, 500 and 700 watts, and activated time (30, 60 and 90 seconds were studied. The results showed that the optimum conditions for activating peanut charcoal were 1:2 (W/V charcoal per activating acid, microwave power 700 watts for 90 seconds. The results yielding maximum surface area by BET method was 303.1 m2 /g and pore volume was 0.140 cm3 /g. An efficiency of maximum iodine adsorption was 418 mg iodine/g activated carbon. Comparing the adsorption efficiency of non- irradiated and irradiated activated carbon, the efficiency of irradiated activated carbon improved up to 31%, due to its larger surface area and pore volume.

Ion conduction mechanisms and thermal properties of hydrated and anhydrous phosphoric acids studied with 1H, 2H, and 31P NMR.

Science.gov (United States)

Aihara, Yuichi; Sonai, Atsuo; Hattori, Mineyuki; Hayamizu, Kikuko

2006-12-14

To understand the behaviors of phosphoric acids in fuel cells, the ion conduction mechanisms of phosphoric acids in condensed states without free water and in a monomer state with water were studied by measuring the ionic conductivity (sigma) using AC impedance, thermal properties, and self-diffusion coefficients (D) and spin-lattice relaxation times (T1) with multinuclear NMR. The self-diffusion coefficient of the protons (H+ or H3O+), H2O, and H located around the phosphate were always larger than the diffusion coefficients of the phosphates and the disparity increased with increasing phosphate concentration. The diffusion coefficients of the samples containing D2O paralleled those in the protonated samples. Since the 1H NMR T1 values exhibited a minimum with temperature, it was possible to determine the correlation times and they were found to be of nanosecond order for a distance of nanometer order for a flip. The agreement of the ionic conductivities measured directly and those calculated from the diffusion coefficients indicates that the ion conduction obeys the Nernst-Einstein equation in the condensed phosphoric acids. The proton diffusion plays a dominant role in the ion conduction, especially in the condensed phosphoric acids.

The Comparison of Hydrochloric Acid and Phosphoric Acid Treatments in the Preparation of Montmorillonite Catalysts for RNA Synthesis.

Science.gov (United States)

Aldersley, Michael Frank; Joshi, Prakash C; Huang, Yixing

2017-09-01

The treatment of clay minerals with a preliminary acid wash and titration to pH 7 has proven to generate catalysts for the most interesting of oligomerization reactions in which activated RNA-nucleotides generate oligomers up to 40-mers. Significantly, not all clay minerals become catalytic following this treatment and none are catalytic in the absence of such treatment. The washing procedure has been modified and explored further using phosphoric acid and the outcomes are compared to those obtained when clay samples are prepared following a hydrochloric acid wash.

Separation of uranium from molybdenum by alkyl phosphoric acid extraction

Energy Technology Data Exchange (ETDEWEB)

Zhongshi, Li

1986-08-01

The regularities of separation of uranium from molybdenum by alkyl phosphoric acid extraction are described. Two parameters, i.e., density ratio of uranium to molybdenum in organic phase at first stage and density of uranium in raffinate at last stage are presented. The relationship between these parameters and purity of molybdenum and uranium products is given. The method of adjusting and controlling these parameters in experiments and production is worked out. The technical key problem in comprehensive utilization of sedimentary type uranium ore containing molybdenum with close concentration of these to elements has been solved.

Potential radiological impacts of recovery of uranium from wet-process phosphoric acid. Final report to the Environmental Protection Agency

International Nuclear Information System (INIS)

Davis, W. Jr.; Haywood, F.F.; Danek, J.L.; Moore, R.E.; Wagner, E.B.; Rupp, E.M.

1979-01-01

A study was made to determine the radiological impacts associated with recovery of uranium from wet-process (WP) phosphoric acid in central Florida. Removal of U and other radionuclides from phosphoric acid prevents their distribution on farm lands and urban gardens and grasses via fertilizers; this results in a positive impact (decreased dose commitment) on the associated populations. This study considers the potential negative impacts of current and project recovery processes in a site-specific manner using detailed state-of-the-art methodologies. Positive impacts are treated in a generic sense using U.S. average values for important variables such as average and maximum fertilizer application rates and quantities of radionuclides in fertilizer. Three model plants to recover U from WP phosphoric acid were selected and source terms for release of radionuclides are developed for all three and for two treatment methods for airborne particulates. Costs for radwaste treatment were developed. Field measurements were conducted at the only commercial uranium recovery plant in operation. Radiological doses to the population surrounding release points during plant operation were estimated

Phosphoric acid as a matrix additive for MALDI MS analysis of phosphopeptides and phosphoproteins

DEFF Research Database (Denmark)

Kjellström, Sven; Jensen, Ole Nørregaard

2004-01-01

Phosphopeptides are often detected with low efficiency by MALDI MS analysis of peptide mixtures. In an effort to improve the phosphopeptide ion response in MALDI MS, we investigated the effects of adding low concentrations of organic and inorganic acids during peptide sample preparation in 2,5-di...... acid to 2,5-DHB were also observed in LC-MALDI-MS analysis of tryptic phosphopeptides of B. subtilis PrkC phosphoprotein. Finally, the mass resolution of MALDI mass spectra of intact proteins was significantly improved by using phosphoric acid in 2,5-DHB matrix....

Process for recovering uranium from wet process phosphoric acid

International Nuclear Information System (INIS)

Pyrih, R.Z.; Rickard, S.; Carrington, F.

1982-01-01

A process for recovering uranium from phosphoric acid solutions uses an acidified alkali metal carbonate solution for the second-stage strip of uranyl uranium from the ion-exchange solution. The stripped solution is then recycled to the ion-exchange circuit. In the first stripping stage the ion-exchange solution containing the recovered uranyl uranium and an inert organic diluent is stripped with ammonium carbonate, producing a slurry of ammonium uranyl tricarbonate. The second strip, with a solution of 50-200 grams per litre of sodium carbonate eliminates the problems of inadequate removal of phosphorus, iron and vanadium impurities, solids accumulation, and phase separation in the strip circuit

Physicotechnical, spectroscopic and thermogravimetric properties of powdered cellulose and microcrystalline cellulose derived from groundnut shells

Directory of Open Access Journals (Sweden)

Chukwuemeka P. Azubuike

2012-09-01

Full Text Available α-Cellulose and microcrystalline cellulose powders, derived from agricultural waste products, that have for the pharmaceutical industry, desirable physical (flow properties were investigated. α–Cellulose (GCN was extracted from groundnut shell (an agricultural waste product using a non-dissolving method based on inorganic reagents. Modification of this α -cellulose was carried out by partially hydrolysing it with 2N hydrochloric acid under reflux to obtain microcrystalline cellulose (MCGN. The physical, spectroscopic and thermal properties of the derived α-cellulose and microcrystalline cellulose powders were compared with Avicel® PH 101, a commercial brand of microcrystalline cellulose (MCCA, using standard methods. X-ray diffraction and infrared spectroscopy analysis showed that the α-cellulose had lower crystallinity. This suggested that treatment with 2N hydrochloric acid led to an increase in the crystallinity index. Thermogravimetric analysis showed quite similar thermal behavior for all cellulose samples, although the α-cellulose had a somewhat lower stability. A comparison of the physical properties between the microcrystalline celluloses and the α-cellulose suggests that microcrystalline cellulose (MCGN and MCCA might have better flow properties. In almost all cases, MCGN and MCCA had similar characteristics. Since groundnut shells are agricultural waste products, its utilization as a source of microcrystalline cellulose might be a good low-cost alternative to the more expensive commercial brand.

Brewer’s Spent Grain Valorization Using Phosphoric Acid Pretreatment for Second Generation Bioethanol Production

DEFF Research Database (Denmark)

Romero, I.; Ruiz, E.; Cara, C.

the effect of phosphoric acid concentration (2-6% w/v) and pretreatment temperature (140-180ºC). The influence of these factors on the hemicellulosic sugar solubilisation and the subsequent enzymatic hydrolysis was evaluated. Optimal pretreatment conditions were determined by maximizing both...... hemicellulosic sugar recovery in liquids and enzymatic hydrolysis yield....

Liquid-liquid extraction for purification of wet process phosphoric acid

International Nuclear Information System (INIS)

Lotfollahi, Mohammad Nader; Bakshi, Mahdi

2006-01-01

The Wet Process Phosphoric Acid (WPA) is used to produce fertilizers and alimentary supplies for cattle. In each of these applications, the impurities contained in acid must be in standard range. In this paper purification of WPA by solvent extraction is performed and the effect of the mass ratio of solvent to feed on extraction efficiency is studied. The working solvents are Methyl Iso Butyl Ketone (MIBK), Iso Amyl Alcohol (IAA) and the mixture of them. The results show that the IAA is better than other solvents in extraction of WPA. This solvent can extract 82.2% of acid after two extraction stages but MIBK can extract only 73.5% of acid after three extraction stages. For all of these solvents, the Pb and Cd concentrations go down to trace. The experimental results show that the maximum separation of Mg with MIBK is 87.5% which occurs at the mass ratio of solvent to feed eual to 4. In the case of IAA solvent the percent is 91.7% and the ratio is 8

Lactic acid demineralization of shrimp shell and chitosan synthesis

Directory of Open Access Journals (Sweden)

Alewo Opuada AMEH

2015-05-01

Full Text Available The use of lactic acid was compared to hydrochloric acid for shrimp shell demineralization in chitosan synthesis. Five different acid concentrations were considered for the study: 1.5M, 3.0M, 4.5M, 6.0M and 7.5M. After demineralization, the shrimp shell were deproteinized and subsequently deacetylated to produce chitosan using sodium hydroxide solution. The synthesized chitosan samples were characterized using solubility, FTIR, SEM, XRD and viscosity. The SEM, FTIR and XRD analysis indicated that chitosan was synthesized with a high degree of deacetylation (83.18±2.11 when lactic acid was used and 84.2±5.00 when HCl was used. The degree of deacetylation and the molecular weight of the chitosan samples were also estimated. ANOVA analysis (at 95% confidence interval indicated that acid type and concentration did not significantly affect the solubility, degree of deacetylation, viscosity and molecular weight of the chitosan within the range considered.

Effect of Reduced Phosphoric Acid Pre-etching Times 
on Enamel Surface Characteristics and Shear Fatigue Strength Using Universal Adhesives.

Science.gov (United States)

Tsujimoto, Akimasa; Fischer, Nicholas; Barkmeier, Wayne; Baruth, Andrew; Takamizawa, Toshiki; Latta, Mark; Miyazaki, Masashi

2017-01-01

To examine the effect of reduced phosphoric acid pre-etching times on enamel fatigue bond strength of universal adhesives and surface characteristics by using atomic force microscopy (AFM). Three universal adhesives were used in this study (Clearfil Universal Bond [C], G-Premio Bond [GP], Scotchbond Universal Adhesive [SU]). Four pre-etching groups were employed: enamel pre-etched with phosphoric acid and immediately rinsed with an air-water spray, and enamel pre-etched with phosphoric acid for 5, 10, or 15 s. Ground enamel was used as the control group. For the initial bond strength test, 15 specimens per etching group for each adhesive were used. For the shear fatigue test, 20 specimens per etching group for each adhesive were loaded using a sine wave at a frequency of 20 Hz for 50,000 cycles or until failure occurred. Initial shear bond strengths and fatigue shear strengths of composite adhesively bonded to ground and pre-etched enamel were determined. AFM observations of ground and pre-etched enamel were also conducted, and surface roughness as well as surface area were evaluated. The initial shear bond strengths and fatigue shear strengths of the universal adhesives in the pre-etched groups were significantly higher than those of the control group, and were not influenced by the pre-etching time. Significantly higher surface roughness and surface area of enamel surfaces in pre-etched groups were observed compared with those in the control group. While the surface area was not significantly influenced by etching time, surface roughness of the enamel surfaces in the pre-etched groups significantly increased with pre-etching time. The results of this in vitro study suggest that reduced phosphoric acid pre-etching times do not impair the fatigue bond strength of universal adhesives. Although fatigue bond strength and surface area were not influenced by phosphoric-acid etching times, surface roughness increased with increasing etching time.

Relation between textural and energetic parameters of activated carbon monoliths from coconut shells

International Nuclear Information System (INIS)

Vargas, Diana Paola; Giraldo, Liliana; Moreno, Juan C.

2009-01-01

Structural characteristics and the energetic parameters of five monoliths of activated carbon were compared. The samples were obtained from coconut shells by means of chemical activation using different concentrations of phosphoric acid. The samples are characterized by means of physical adsorption of N 2 at 77K, CO 2 at 273K, and immersion calorimetry in benzene. From the data obtained the volumes of micropore, mesopore, narrow micro porosity and energy parameters of immersion enthalpy were calculated. Also were calculated, K of the Langmuir model and characteristic energies, Eo, of the Dubinin-Radushkevich model. The experimental results show that the activation with phosphoric acid develops micro porosity, giving a micropore volume between 0,36 and 0,45 cm 3 g-1, area BET between 975 and 1320 m 2 g-1 and immersion enthalpy between 112,9 and 147,7 Jg-1. It was found that for higher BET area, there is a greater immersion enthalpy in benzene, lower characteristic energy and smaller value of K.

A new oxidimetric reagent: potassium dichromate in a strong phosphoric acid medium--VII. Photometric titration of vanadium(IV) and of cerium(III) alone and in mixtures with iroN(II).

Science.gov (United States)

Rao, G G; Rao, P K

1967-01-01

Vanadium(IV) can be accurately titrated with potassium dichromate in media containing phosphoric acid of 3-12M concentration: the change in absorption of vanadium(IV) is followed in the region 660 mmicro using a red filter. It is more convenient to carry out the titration in 3M phosphoric acid because at higher concentrations chloride, nitrate, cerium(III) and manganese(II) may interfere. Photoelcetric titration is more convenient than potentiometric because the former can be made in a 3M phosphoric acid medium, whereas the latter is possible only in 12M phosphoric acid. The simultaneous differential photometric titration of iron(II) and vanadium(IV) is also possible. Conditions have been found for the photometric titration of cerium(III) and of cerium(III) plus iron(II). The titration is carried out (at 450 mmicro or with a blue filter) in about 10.5M phosphoric acid. Application of the method to a cerium mineral is considered.

SYNTHESIS OF FLAVANONE-6-CARBOXYLIC ACID DERIVATIVES FROM SALICYLIC ACID DERIVATIVE

Directory of Open Access Journals (Sweden)

Muhammad Idham Darussalam Mardjan

2012-02-01

Full Text Available Synthesis of flavanone-6-carboxylic acid derivatives had been conducted via the route of chalcone. The synthesis was carried out from salicylic acid derivative, i.e. 4-hydroxybenzoic acid, via esterification, Fries rearrangement, Claisen-Schmidt condensation and 1,4-nucleophilic addition reactions. Structure elucidation of products was performed using FT-IR, 1H-NMR, GC-MS and UV-Vis spectrometers. Reaction of 4-hydroxybenzoic acid with methanol catalyzed with sulfuric acid produced methyl 4-hydroxybenzoate in 87% yield. The acid-catalyzed-acetylation of the product using acetic anhydride gave methyl 4-acetoxybenzoate in 75% yield. Furthermore, solvent-free Fries rearrangement of methyl 4-acetoxybenzoate in the presence of AlCl3 produced 3-acetyl-4-hydroxybenzoic acid as the acetophenone derivatives in 67% yield. Then, Claisen-Schmidt condensation of the acetophenone and benzaldehyde derivatives of p-anisaldehyde and veratraldehyde in basic condition gave 2'-hydroxychalcone-5'-carboxylic acid derivatives  in 81 and 71 % yield, respectively. Finally, the ring closure reaction of the chalcone yielded the corresponding flavanone-6-carboxylic acids in 67 and 59% yield, respectively.

Woking Park phosphoric acid fuel cell CHP monitoring

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-09-15

A phosphoric acid fuel (PC25) delivering up to 200kw of electrical power and commensurate heat was installed in Woking Park UK in late 2006 and has been monitored over a period of one year. The system supplies electric power to a leisure centre and swimming pool via a private wires network. This report gives details of the monitoring and shows a schematic of the system, data on electrical and thermal efficiencies, stack voltage variations and gaseous emissions. Extended monitoring is now taking place to provide a complete picture of the economics and operation of the fuel cell in the developing combined heat and power unit and private wires system. The contractor is Advantica of Loughborough and detailed results of the monitoring are available on the DTI website.

Study of the properties of dialkyl thiophosphoric acids. Application to the extraction of U, in phosphoric and nitric solutions

International Nuclear Information System (INIS)

Benjelloun, N.

1983-09-01

A study is made of complex formation and liquid-liquid extraction of uranium (VI) by dialkyl-thiophosphoric acids of formula (RO) 2 POSH and by the synergic mixtures: dialkylthiophosphoric acids-phosphine oxides. The aqueous phases studied consist of concentrated phosphoric acid solutions and nitric acid solutions. Several methods, including distribution coefficient measurements, U.V., visible and infrared absorption spectrophotometries and magnetic resonance, were used to study the extraction mechanisms and the structures of species formed in the organic phase. The influence of different parameters (partition of extraction agent, dimerisation, acid ligand-phosphine oxide association, extraction of inorganic acids...) on the uranium (VI) distribution coefficients enabled the constants of complex formation in the aqueous phase and extraction in the organic phase to be determined. These various properties were compared with those of dialkyl phosphoric and dithiophosphoric acids. The mechanisms established prove that sulfur donors ligands form stable complexes with UO 2 2+ ions although U(VI) is considered as a ''hard class a'' acceptor according to Ahrland's classification [fr

Influence of duration of phosphoric acid pre-etching on bond durability of universal adhesives and surface free-energy characteristics of enamel.

Science.gov (United States)

Tsujimoto, Akimasa; Barkmeier, Wayne W; Takamizawa, Toshiki; Watanabe, Hidehiko; Johnson, William W; Latta, Mark A; Miyazaki, Masashi

2016-08-01

The purpose of this study was to evaluate the influence of duration of phosphoric acid pre-etching on the bond durability of universal adhesives and the surface free-energy characteristics of enamel. Three universal adhesives and extracted human molars were used. Two no-pre-etching groups were prepared: ground enamel; and enamel after ultrasonic cleaning with distilled water for 30 s to remove the smear layer. Four pre-etching groups were prepared: enamel pre-etched with phosphoric acid for 3, 5, 10, and 15 s. Shear bond strength (SBS) values of universal adhesive after no thermal cycling and after 30,000 or 60,000 thermal cycles, and surface free-energy values of enamel surfaces, calculated from contact angle measurements, were determined. The specimens that had been pre-etched showed significantly higher SBS and surface free-energy values than the specimens that had not been pre-etched, regardless of the aging condition and adhesive type. The SBS and surface free-energy values did not increase for pre-etching times of longer than 3 s. There were no significant differences in SBS values and surface free-energy characteristics between the specimens with and without a smear layer. The results of this study suggest that phosphoric acid pre-etching of enamel improves the bond durability of universal adhesives and the surface free-energy characteristics of enamel, but these bonding properties do not increase for phosphoric acid pre-etching times of longer than 3 s. © 2016 Eur J Oral Sci.

Electrolytes for methanol-air fuel cells. I. The performance of methanol electro-oxidation catalysts in sulphuric acid and phosphoric acid electrolytes

Energy Technology Data Exchange (ETDEWEB)

Andrew, M.R.; McNicol, B.D.; Short, R.T.; Drury, J.S.

1977-03-01

Phosphoric acid and sulphuric acid have been compared as potential electrolytes for methanol-air fuel cells. The performances of typical electro-oxidation catalysts were measured in both electrolytes over a range of concentrations. With all catalysts the activity falls with increasing acid concentration. While this is to some extent due to the decrease in water activity at higher concentrations it seems that with both acids there is significant poisoning of the catalyst. The results can be explained for both electrolytes by assuming that adsorption of undissociated acid poisons the catalyst surfaces and that the reaction rate on the poisoned surfaces is proportional to the water activity.

Nanocellulose Derivative/Silica Hybrid Core-Shell Chiral Stationary Phase: Preparation and Enantioseparation Performance

Directory of Open Access Journals (Sweden)

Xiaoli Zhang

2016-05-01

Full Text Available Core-shell silica microspheres with a nanocellulose derivative in the hybrid shell were successfully prepared as a chiral stationary phase by a layer-by-layer self-assembly method. The hybrid shell assembled on the silica core was formed using a surfactant as template by the copolymerization reaction of tetraethyl orthosilicate and the nanocellulose derivative bearing triethoxysilyl and 3,5-dimethylphenyl groups. The resulting nanocellulose hybrid core-shell chiral packing materials (CPMs were characterized and packed into columns, and their enantioseparation performance was evaluated by high performance liquid chromatography. The results showed that CPMs exhibited uniform surface morphology and core-shell structures. Various types of chiral compounds were efficiently separated under normal and reversed phase mode. Moreover, chloroform and tetrahydrofuran as mobile phase additives could obviously improve the resolution during the chiral separation processes. CPMs still have good chiral separation property when eluted with solvent systems with a high content of tetrahydrofuran and chloroform, which proved the high solvent resistance of this new material.

Characterization of Physic nut (Jatropha curcas L.) shells

International Nuclear Information System (INIS)

Wever, Diego-Armando Z.; Heeres, H.J.; Broekhuis, Antonius A.

2012-01-01

The characterization of Physic nut shells was done using the wet chemical analysis of wood components. The obtained fractions were analyzed using IR, NMR, GPC, ICP and MALDI-TOF mass spectroscopy. TGA was used to determine the fixed carbon (+ash) and water content of the shells. The results of wet chemical analysis of wood components offered a clear procedure to isolate the main components in Physic nut shells (a). The fractions obtained were: polar extract (b), non-polar extract (c), Acid Insoluble Lignin (d), Holocellulose (e), α-Cellulose (f). The total Lignin content present in the shells equaled 48.84%. IR and NMR spectroscopy demonstrated that the non-polar extract is Lignin, which corresponds to the extractable Lignin (1.24%) in the Physic nut shells and the Acid Insoluble Lignin was 47.60%. Elemental analysis showed no Sulfur present in the investigated materials. Furthermore both 1 H and 13 C NMR of the non-polar extract showed the presence of aliphatic hydrocarbon chains. The α-Cellulose content (22.29%) and the Hemicelluloses content (23.84%) were in line with that of agricultural residues. The water content and the fixed carbon content (+ash [2.8%]) equal 5–6% and 35.6%, respectively. GPC showed that the polydispersity of the non-polar extract (3.6) lies between Alcell Lignin and Kraft Lignin. The polar extract contains a variety of metals, with especially a high amount of the alkali metals K and Na. The extraction with water is proposed to generate a fertilizer fraction and may be applied to reduce potential sintering issues during eventual combustion or gasification of the shells. -- Highlights: ► Physic nut shell is a potential source of value added chemicals due to its high lignin content (48.8 wt%). ► Lignin extracted from Jatropha curcas L. shells is rich in aliphatic linkages. ► Water extraction of the shells yields a potential fertilizer fraction rich in alkali metals and phosphorous. ► Pre-extraction is recommended to eliminate

Porous HKUST-1 derived CuO/Cu2O shell wrapped Cu(OH)2 derived CuO/Cu2O core nanowire arrays for electrochemical nonenzymatic glucose sensors with ultrahigh sensitivity

Science.gov (United States)

Yu, Cuiping; Cui, Jiewu; Wang, Yan; Zheng, Hongmei; Zhang, Jianfang; Shu, Xia; Liu, Jiaqin; Zhang, Yong; Wu, Yucheng

2018-05-01

Self-supported CuO/Cu2O@CuO/Cu2O core-shell nanowire arrays (NWAs) are successfully fabricated by a simple and efficient method in this paper. Anodized Cu(OH)2 NWAs could in-situ convert to HKUST-1 at room temperature easily. Cu(OH)2 NWAs cores and HKUST-1 shells transform into CuO/Cu2O simultaneously after calcinations and form CuO/Cu2O@CuO/Cu2O core-shell NWAs. This smart configuration of the core-shell structure not only avoids the agglomeration of the traditional MOF-derived materials in particle-shape, but also facilitates the ion diffusion and increases the active sites. This novel structure is employed as substrate to construct nonenzymatic glucose sensors. The results indicate that glucose sensor based on CuO/Cu2O@CuO/Cu2O core-shell NWAs presents ultrahigh sensitivity (10,090 μA mM-1 cm-2), low detection limit (0.48 μM) and wide linear range (0.99-1,330 μM). In addition, it also shows excellent anti-interference ability toward uric acid, ascorbic acid and L-Cysteine co-existing with glucose, good reproducibility and superior ability of real sample analysis.

On the reaction of iron oxides and oxyhydroxides with tannic and phosphoric acid and their mixtures

Energy Technology Data Exchange (ETDEWEB)

Beltran, J. J., E-mail: jjbj08@yahoo.com; Novegil, F. J.; Garcia, K. E.; Barrero, C. A. [Universidad de Antioquia, Sede de Investigacion Universitaria, Grupo de Estado Solido, Instituto de Fisica (Colombia)

2010-01-15

The actions of tannic acid, phosphoric acid and their mixture on lepidocrocite, goethite, superparamagnetic goethite, akaganeite, magnetite, hematite and maghemite for 1 day and 1 month were explored. It was found that these acids form iron tannates and phosphates. Lepidocrocite and magnetite were the iron phases more easily transformed with the mixture of the acids after 1 month of reaction, whereas hematite was the most resistant phase. In the case of goethite, our results suggest that in order to understand properly the action of these acids, we have to take into account its stoichiometry, surface area and degree of crystallinity.

Phosphorous gettering in acidic textured multicrystalline solar cells

Energy Technology Data Exchange (ETDEWEB)

Montesdeoca-Santana, A. [Departamento de Fisica Basica, Universidad de La Laguna (ULL), Avenida Astrofisico Francisco Sanchez 2, 38206 La Laguna, S/C de Tenerife (Spain); Fraunhofer Institut fuer Solare Energiesysteme ISE, Laboratory and Servicecenter Gelsenkirchen, Auf der Reihe 2, 45884 Gelsenkirchen (Germany); Jimenez-Rodriguez, E.; Diaz-Herrera, B.; Hernandez-Rodriguez, C. [Departamento de Fisica Basica, Universidad de La Laguna (ULL), Avenida Astrofisico Francisco Sanchez 2, 38206 La Laguna, S/C de Tenerife (Spain); Gonzalez-Diaz, B. [Departamento de Fisica Basica, Universidad de La Laguna (ULL), Avenida Astrofisico Francisco Sanchez 2, 38206 La Laguna, S/C de Tenerife (Spain); Departamento de Energia Fotovoltaica, Instituto Tecnologico y de Energias Renovables. Poligono Industrial de Granadilla s/n, 38600 San Isidro-Granadilla de Abona, S/C de Tenerife (Spain); Rinio, M.; Borchert, D. [Fraunhofer Institut fuer Solare Energiesysteme ISE, Laboratory and Servicecenter Gelsenkirchen, Auf der Reihe 2, 45884 Gelsenkirchen (Germany); Guerrero-Lemus, R. [Departamento de Fisica Basica, Universidad de La Laguna (ULL), Avenida Astrofisico Francisco Sanchez 2, 38206 La Laguna, S/C de Tenerife (Spain); Fundacion de Estudios de Economia Aplicada, Catedra Focus-Abengoa, Jorge Juan 46, 28001 Madrid (Spain)

2011-03-15

The influence of phosphorus gettering is studied in this work applied to an acidic textured multicrystalline silicon substrate. The texturization was achieved with an HF/HNO{sub 3} solution leading to nanostructures on the silicon surface. It has been demonstrated in previous works that this textured surface decreases the reflectance on the solar cell and increases the surface area improving the photon collection and enhancing the short circuit current. The present study investigates the effect on the minority carrier lifetime of the phosphorous diffusion when it is carried out on this textured surface. The lifetime is measured by means microwave photoconductance decay and quasi steady state phototoconductance devices. The diffused textured wafers are used to fabricate solar cells and their electrical parameters are analyzed. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The optimisation study of tbp synthesis process by phosphoric acid

International Nuclear Information System (INIS)

Amedjkouh, A.; Attou, M.; Azzouz, A.; Zaoui, B.

1995-07-01

The present work deals with the optimisation study of TBP synthesis process by phosphoric acid. This way of synthesis is more advantageous than POCL3 or P2O5 as phosphatant agents. these latters are toxic and dangerous for the environnement. The optimisation study is based on a series of 16 experiences taking into account the range of variation of the following parameters : temperature, pressure, reagents mole ratio, promoter content. the yield calculation is based on the randomisation of an equation including all parameters. the resolution of this equation gave a 30% TBP molar ratio. this value is in agreement with that of experimental data

Carbon components in the phosphoric acid fuel cell-an overview

International Nuclear Information System (INIS)

Appleby, J.

1983-01-01

The single breakthrough that has made the phosphoric acid fuel cell a practical reality has been the use of carbon or graphite components for the repeat parts of the cell stack. While the thermodynamic stability of carbon is such that rapid corrosion would be expected at the cathode at fuel cell operating temperature, its kinetic stability is remarkable despite the absence of passivating layers analogous to those on, for example, the Group VA elements niobium and tantalum. This happy accident, combined with the adequate electronic conductivity of the carbon materials used, has provided the opportunity to reduce fuel cell cost to attractive levels. The development of these carbon compounds is reviewed

Uranium(VI) and ruthenium extraction by dialkyldithio-phosphoric acids

International Nuclear Information System (INIS)

Fitoussi, R.; Musikas, C.

1980-01-01

Oxygen donors like dialkylphosphoric acids are good extractants for actinide ions, but little is known about their sulfur homologs. Investigations of U(VI) and Ru extraction from various aqueous media are reported. This includes extraction of U(VI) from nitric, perchloric, and phosphoric acids by solutions of dialkyldithiophosphoric acids in dodecane or benzene. Extraction of U(VI) by synergistic mixtures, of which at least one of the components is a sulfur donor, has been investigated. The extracted species have been identified, and a comparison with the complexes obtained by extraction with the homologous oxygen donors is made. The sulfur-actinide bond is weaker than the oxygen-actinide one, but in some synergistic extractions the dialkyldithiophosphonates are more efficient than the oxygen donors. In addition to size effects, this behavior could be attributed to the weakness of the hydrogen bonds of the SH groups, which allows a greater variety of the ligands to enter the coordination sphere of the metal. Ruthenium, like the d-transition elements, gives strong bonds with the sulfur donors. However, its extraction from nitric acid is slow. We investigated the influence of several parameters on the distribution coefficients and found that the presence of a reagent which destroys nitrous ions is necessary to achieve quantitative extraction. The role of RuNO groups is also discussed

Natural Radiation in byproducts of the production of phosphoric acid; Radiacao natural em residuos gerados no processo de producao de acido fosforico

Energy Technology Data Exchange (ETDEWEB)

Silveira, Marcilei A. Guazzelli da; Cardoso, L.L., E-mail: marcilei@fei.edu.br [Centro Universitario da FEI, Sao Bernardo do Campo, SP (Brazil); Medina, N.H. [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Institutlo de Fisica

2014-07-01

Natural radiation is the largest source of radiation exposure to which man is subject. It is formed basically by cosmic radiation and the radionuclides present in the Earth crust, as {sup 40}K and the elements of the decay series of {sup 232}Th and {sup 238}U. Phosphate ores, which constitutes the raw material for the production of phosphoric acid, have a high rate of natural radiation from the decay series of {sup 232}Th and {sup 238}U. Phosphogypsum, which is naturally radioactivity, is a by-product of the production of phosphoric acid by the wet method. For each ton of phosphoric acid it is produced about 4.5 tons of phosphogypsum. This work presents the analysis of samples collected in all stages of the manufacturing process of phosphoric acid, which generates the phosphogypsum. Gamma-ray spectrometry was used to measure the concentration of the elements of the decay series of {sup 232}Th and {sup 238}U. All analyzed samples showed a high concentration of radionuclides, promoting the need for further steps in the process in order to reduce the presence of such radionuclides in the phosphogypsum. The results indicate the radionuclide {sup 238}U has higher contribution in some samples of the intermediate stages of the process. All samples exceeded the international average range of human exposure to terrestrial gamma radiation, which is 0.3 to 1.0 mSv/year. (author)

[Acids in coffee. XI. The proportion of individual acids in the total titratable acid].

Science.gov (United States)

Engelhardt, U H; Maier, H G

1985-07-01

22 acids in ground roast coffees and instant coffees were determined by GLC of their silyl derivatives (after preseparation by gel electrophoresis) or isotachophoresis. The contribution to the total acidity (which was estimated by titration to pH 8 after cation exchange of the coffee solutions) was calculated for each individual acid. The mentioned acids contribute with 67% (roast coffee) and 72% (instant coffee) to the total acidity. In the first place citric acid (12.2% in roast coffee/10.7% in instant coffee), acetic acid (11.2%/8.8%) and the high molecular weight acids (8%/9%) contribute to the total acidity. Also to be mentioned are the shares of chlorogenic acids (9%/4.8%), formic acid (5.3%/4.6%), quinic acid (4.7%/5.9%), malic acid (3.9%/3%) and phosphoric acid (2.5%/5.2%). A notable difference in the contribution to total acidity between roast and instant coffee was found for phosphoric acid and pyrrolidonecarboxylic acid (0.7%/1.9%). It can be concluded that those two acids are formed or released from e.g. their esters in higher amounts than other acids during the production of instant coffee.

Synthesis of a chelate resin with amido and phosphoric acid and its character in uranium extraction

International Nuclear Information System (INIS)

Qiu Yueshuang; Zhang Jianguo; Feng Yu; Zhao Chaoya

2013-01-01

A chelate resin (D814) with amido and phosphoric acid functional group was synthetized by means of the reactions of stytene-divinyl benzene chloromethylated sphere with ethylenedianmine and orth-phosphorous acid and formaldehyde. This resin can be used to adsorb uranium from leaching solution with high chloride ion in the rang of pH l.33-9.05, and the adsorption rate of uranium was above 95%. D814 resin had a good ability resistant to high chloride ion. The loading capacity for uranium was not apparently effected when chlorid ion concentration in solution was 60 g/L. The results of the adsorption experiment show that when the ratio of saturation volume to breakthrough volume was l.82, the uranium saturation capacity of D814 was 40.5 mg/g dry resin. NaCl + NaHCO 3 was used for eluting agent, and the eluting rate of uranium was 96.7%. Adsorption uranium mechanism by D814 was also discussed. (authors)

Corrosion rate of construction materials in hot phosphoric acid with the contribution of anodic polarization

DEFF Research Database (Denmark)

Kouril, M.; Christensen, Erik; Eriksen, S.

2011-01-01

The paper is focused on selection of a proper material for construction elements of water electrolysers, which make use of a 85% phosphoric acid as an electrolyte at temperature of 150 8C and which might be loaded with anodic polarization up to 2.5 V versus a saturated Ag/AgCl electrode (SSCE...

Corrosion inhibition of austenitic stainless steel by clay in polluted phosphoric acid with presence of SiC abrasif

Directory of Open Access Journals (Sweden)

Skal S.

2018-01-01

Full Text Available Stainless steels have many properties mechanical and chemical resistances resulting from the formation of the protective layer (passive film on their surface which prevents the metal to react with corrosive environments such as, phosphoric acid. This acid contains various impurities, including agressive agents and solid particles of gypsum, increase the risk of corrosion damage depending on the type of stainless steel used. In addition, it has been show that abrasion-corrosion causes an acceleration electrochemical process leading to a decrease in the resistance of materials. This work is to find a solution through an ecological inhibitor. That why we have been studied the effect of crude clay on corrosion behavior of Alloy 31 in polluted phosphoric acid with abrasive by electrochemical impedance spectroscopy (EIS . The clay was characterized by X-ray fluorescence spectroscopy (FX, X-ray diffraction (DRX and infrared spectroscopy (IR. EIS exhibited that resistance of Alloy 31 increased with increase the concentration of inhibitor.

Spectrophotometric and potentiometric studies of oxidation of Mo(III) by Mo(VI) in phosphoric acid medium

Energy Technology Data Exchange (ETDEWEB)

Kumar, A; Verma, G S.P. [Ranchi Coll. (India). Dept. of Chemistry

1975-12-01

Oxidation of Mo(III) (green) by Mo(VI) in an inert atmosphere and in orthophosphoric acid medium at various acid concentrations is reported. Potentiometric and spectrophotometric data suggest that oxidation of Mo(III) proceeds to Mo(V) through a binuclear species Mo(III) Mo(IV) absorbing at 400 nm. The formation of this species is facilitated at high acid concentrations. It is further found that quantitative conversion of Mo(III) into Mo(V) takes place at fairly high acid concentrations. In high phosphoric acid concentrations, solution of Mo(III) has been found to be oxidized to Mo(VI) by air and hence this can be used as a good oxygen absorber.

Nanoporous anodic aluminum oxide with a long-range order and tunable cell sizes by phosphoric acid anodization on pre-patterned substrates

Science.gov (United States)

Surawathanawises, Krissada; Cheng, Xuanhong

2014-01-01

Nanoporous anodic aluminum oxide (AAO) has been explored for various applications due to its regular cell arrangement and relatively easy fabrication processes. However, conventional two-step anodization based on self-organization only allows the fabrication of a few discrete cell sizes and formation of small domains of hexagonally packed pores. Recent efforts to pre-pattern aluminum followed with anodization significantly improve the regularity and available pore geometries in AAO, while systematic study of the anodization condition, especially the impact of acid composition on pore formation guided by nanoindentation is still lacking. In this work, we pre-patterned aluminium thin films using ordered monolayers of silica beads and formed porous AAO in a single-step anodization in phosphoric acid. Controllable cell sizes ranging from 280 nm to 760 nm were obtained, matching the diameters of the silica nanobead molds used. This range of cell size is significantly greater than what has been reported for AAO formed in phosphoric acid in the literature. In addition, the relationships between the acid concentration, cell size, pore size, anodization voltage and film growth rate were studied quantitatively. The results are consistent with the theory of oxide formation through an electrochemical reaction. Not only does this study provide useful operational conditions of nanoindentation induced anodization in phosphoric acid, it also generates significant information for fundamental understanding of AAO formation. PMID:24535886

Luminescent features of sol–gel derived rare-earth multi-doped oxyfluoride nano-structured phosphors for white LED application

International Nuclear Information System (INIS)

Gouveia-Neto, A.S.; Silva, A.F. da; Bueno, L.A.; Costa, E.B. da

2012-01-01

Rare-earth doped oxyfluoride 75SiO 2 :25PbF 2 nano-structured phosphors for white-light-emitting diodes were synthesized by thermal treatment of precursor sol–gel derived glasses. Room temperature luminescence features of Eu 3+ , Sm 3+ , Tb 3+ , Eu 3+ /Tb 3+ , and Sm 3+ /Tb 3+ ions incorporated into low-phonon-energy PbF 2 nanocrystals dispersed in the aluminosilicate glass matrix and excited with UV light emitting diode were investigated. The luminescence spectra exhibited strong emission signals in the red (600, 610, 625, and 646 nm), green (548 and 560 nm), and blue (485 nm) wavelength regions. White-light emission was observed in Sm/Tb and Eu/Tb double-doped activated phosphors employing UV-LED excitation at 395 nm. The dependence of the luminescence emission intensities upon annealing temperature and rare-earth concentration was also examined. The results indicated that there exist optimum annealing temperature and activator ion concentration in order to obtain intense visible emission light with high color rendering index. The study suggests that the nanocomposite phosphor based upon 75SiO 2 :25PbF 2 host herein reported is a promising contender for white-light LED applications. - Highlights: ► White-light emission in double-doped activated phosphors employing UV-LED excitation. ► Luminescent features of europium, samarium, and terbium in nanocrystals dispersed in aluminosilicate glass. ► New nanocomposite phosphor host for white-light LED applications.

Ion flotation of uranium contained in industrial phosphoric acid with collector recycling

International Nuclear Information System (INIS)

Jdid, E.; Blazy, P.; Bessiere, J.

1985-01-01

Uranium has been recovered from wet-process phosphoric acid (30% P 2 O 5 ) by ion flotation with an anionic organophosphorous collector. Recoveries greater than 90% were obtained even at temperatures of about 60 C, the uranium concentrate, which was collected in the froth as a precipitate, containing 7 to 10% U. Collector consumption without recycling of the surface-active reagent was about 12 kg/kg U. Much of the reagent, however, can be recovered for recycling by attack with sodium hydroxide on the floated phase after filtration. This enables a precipitate containing about 30% U to be produced and decreases collector consumption to about 3 kg/kg U. The results were obtained in laboratory-scale experiments on industrial wet-process acid. (author)

Color stable manganese-doped phosphors

Science.gov (United States)

Lyons, Robert Joseph [Burnt Hills, NY; Setlur, Anant Achyut [Niskayuna, NY; Deshpande, Anirudha Rajendra [Twinsburg, OH; Grigorov, Ljudmil Slavchev [Sofia, BG

2012-08-28

A process for preparing color stable Mn.sup.+4 doped phosphors includes providing a phosphor of formula I; A.sub.x[MF.sub.y]:Mn.sup.+4 I and contacting the phosphor in particulate form with a saturated solution of a composition of formula II in aqueous hydrofluoric acid; A.sub.x[MF.sub.y]; II wherein A is Li, Na, K, Rb, Cs, NR.sub.4 or a combination thereof; M is Si, Ge, Sn, Ti, Zr, Al, Ga, In, Sc, Y, La, Nb, Ta, Bi, Gd, or a combination thereof; R is H, lower alkyl, or a combination thereof; x is the absolute value of the charge of the [MF.sub.y] ion; and y is 5, 6 or 7. In particular embodiments, M is Si, Ge, Sn, Ti, Zr, or a combination thereof. A lighting apparatus capable of emitting white light includes a semiconductor light source; and a phosphor composition radiationally coupled to the light source, and which includes a color stable Mn.sup.+4 doped phosphor.

Phosphoric acid fuel cell platinum use study

Science.gov (United States)

Lundblad, H. L.

1983-05-01

The U.S. Department of Energy is promoting the private development of phosphoric acid fuel cell (PAFC) power plants for terrestrial applications. Current PAFC technology utilizes platinum as catalysts in the power electrodes. The possible repercussions that the platinum demand of PAFC power plant commercialization will have on the worldwide supply and price of platinum from the outset of commercialization to the year 2000 are investigated. The platinum demand of PAFC commercialization is estimated by developing forecasts of platinum use per unit of generating capacity and penetration of PAFC power plants into the electric generation market. The ability of the platinum supply market to meet future demands is gauged by assessing the size of platinum reserves and the capability of platinum producers to extract, refine and market sufficient quantities of these reserves. The size and timing of platinum price shifts induced by the added demand of PAFC commercialization are investigated by several analytical methods. Estimates of these price shifts are then used to calculate the subsequent effects on PAFC power plant capital costs.

Tensile bond strength and SEM analysis of enamel etched with Er:YAG laser and phosphoric acid: a comparative study in vitro

International Nuclear Information System (INIS)

Sasaki, Luis H.; Tanaka, Celso Shin-Ite; Lobo, Paulo D.C.; Villaverde, Antonio B.; Moriyama, Eduardo H.; Brugnera Junior, Aldo; Moriyama, Yumi; Watanabe, Ii-Sei

2008-01-01

Er:YAG laser has been studied as a potential tool for restorative dentistry due to its ability to selectively remove oral hard tissue with minimal or no thermal damage to the surrounding tissues. The purpose of this study was to evaluate in vitro the tensile bond strength (TBS) of an adhesive/composite resin system to human enamel surfaces treated with 37% phosphoric acid, Er:YAG laser (λ=2.94 μm) with a total energy of 16 J (80 mJ/pulse, 2Hz, 200 pulses, 250 ms pulse width), and Er:YAG laser followed by phosphoric acid etching. Analysis of the treated surfaces was performed by scanning electron microscopy (SEM) to assess morphological differences among the groups. TBS means (in MPa) were as follows: Er:YAG laser + acid (11.7 MPa) > acid (8.2 MPa) > Er:YAG laser (6.1 MPa), with the group treated with laser+acid being significantly from the other groups (p=0.0006 and p= 0.00019, respectively). The groups treated with acid alone and laser alone were significantly different from each other (p=0.0003). The SEM analysis revealed morphological changes that corroborate the TBS results, suggesting that the differences in TBS means among the groups are related to the different etching patterns produced by each type of surface treatment. The findings of this study indicate that the association between Er:YAG laser and phosphoric acid can be used as a valuable resource to increase bond strength to laser-prepared enamel. (author)

The use of Syrian bentonite to remove organics and other ions from commercial Syrian phosphoric acid

International Nuclear Information System (INIS)

Khorfan, S.; Abdulbaki, M.; Zein, A.

2006-01-01

Using of activated carbon to remove organic matter from phosphoric acid in uranium and P 2 O 5 extraction units has high cost. A new study was conducted to establish a new material instead of activated carbon. Experiments were carried out on removing organic matter by adsorption on Syrian bentonite. The experiments of the removal of humic acid by Syrian bentonite gave good results and showed that the chemical and thermal activation of bentonite increased the adsorption efficiency. (Authors)

The use of Syrian bentonite to remove organics and other ions from commercial Syrian phosphoric acid

International Nuclear Information System (INIS)

Khorfan, S.; Abdulbaki, M.; Zein, A.

2005-03-01

Using of activated carbon to remove organic matter from phosphoric acid in uranium and P 2 O 5 extraction units has high cost. A new study was conducted to establish a new material instead of activated carbon. Experiments were carried out on removing organic matter by adsorption on Syrian bentonite. The experiments of the removal of humic acid by Syrian bentonite gave good results and showed that the chemical and thermal activation of bentonite increased the adsorption efficiency. (Authors)

MXP(M = Co/Ni)@carbon core-shell nanoparticles embedded in 3D cross-linked graphene aerogel derived from seaweed biomass for hydrogen evolution reaction.

Science.gov (United States)

Zhao, Wentong; Lu, Xiaoqing; Selvaraj, Manickam; Wei, Wei; Jiang, Zhifeng; Ullah, Nabi; Liu, Jie; Xie, Jimin

2018-05-24

Low-cost electrocatalysts play an important role in the hydrogen evolution reaction (HER). Particularly, transition metal phosphides (TMPs) are widely applied in the development of HER electrocatalysts. To improve the poor electrochemical reaction kinetics of HER, we introduce a facile way to synthesize carbon core-shell materials containing cobalt phosphide nanoparticles embedded in different graphene aerogels (GAs) (CoP@C-NPs/GA-x (x = 5, 10 and 20)) using seaweed biomass as precursors. The synthesized CoP@C-NPs/GA-5 exhibits efficient catalytic activity with small overpotentials of 120 and 225 mV at current densities of 10 mA cm-2, along with the low Tafel slopes of 57 and 66 mV dec-1, for HER in acidic and alkaline electrolytes, respectively. Compared with carbon aerogel (CA) containing cobalt phosphide nanoparticles (CoP-NPs@CA), the stability of CoP@C-NPs/GA-5 coated with carbon-shells (∼0.8 nm) was significantly improved in acidic electrolytes. We also prepared carbon core-shell materials containing nickel phosphide nanoparticles embedded in GA (Ni2P@C-NPs/GA) to further expand this synthetic route. The graphene-Ni2P@C aerogel shows a similar morphology and better catalytic activity for HER in acidic and alkaline electrolytes. In this work, the robust three-dimensional (3D) GA matrix with abundant open pores and large surface area provides unblocked channels for electrolyte contact and electronic transfer and enables very close contact between the catalyst and electrolyte. The MxP@C core-shell structure prevents the inactivation of MxP NPs during HER processes, and the thin graphene oxide (GO) layers and 3D CA together build up a 3D conductive matrix, which not only adjusts the volume expansion of MxP NPs as well as preventing their aggregation, but also provides a 3D conductive pathway for rapid charge transfer processes. The present synthetic strategy for phosphides via in situ phosphorization with 3D GA can be extended to other novel high

Cyclodextrin-Triazole Derivative Functionalized on Ag-SiO{sub 2} Core-Shell Nanoparticles via Click Chemistry

Energy Technology Data Exchange (ETDEWEB)

Park, Gun Bae; Singu, Bal Sydulu; Hong, Sang Eun; Yoon, Kuk Ro [Hannam Univ., Daejeon (Korea, Republic of)

2016-09-15

Click chemistry has provided a versatile strategy for functionalization in solution chemistry under mild reaction conditions with a high degree of functional group compatibility. Initially, silver (Ag) nanoparticles were prepared by the chemical reduction method, followed by the synthesis of silver–silica (Ag–SiO{sub 2}) core–shell nanoparticles by the Stöber method. The Ag–SiO2 core shell nanoparticles were functionalized with the alkyne derivative. The cycloaddition reaction between the azide-functionalized cyclodextrin and the alkyne-functionalized Ag–SiO{sub 2} core–shell nanoparticles was carried out via the copper-catalyzed click reaction, leading to the formation of the cyclodextrin-triazole derivative on the Ag–SiO{sub 2} core–shell nanoparticles. The presence of the resulting cyclodextrin-triazole derivative on the silver–silica core–shell nanoparticles was confirmed by Fourier transform infrared spectroscopy (FT-IR), ultraviolet–visible spectroscopy (UV–vis), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA).

The impact of water concentration on the catalytic oxidation of ethanol on platinum electrode in concentrated phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Camargo, A.P.M.; Previdello, B.A.F.; Varela, H.; Gonzalez, E.R. [Instituto de Quimica de Sao Carlos, Universidade de Sao Paulo, C.P. 780, CEP 13560-970 Sao Carlos, SP (Brazil)

2010-01-15

The electro-oxidation of ethanol on platinum in phosphoric acid opens the door to promote the oxidation reaction at higher temperatures. However, the effect of the presence of water is not well understood. In this work, the electro-oxidation of ethanol on platinum was studied in concentrated phosphoric acid containing different concentrations of water at room temperature. The results show that effect of bulk water on the rate electro-oxidation is highest at 0.60 V and decreases for increasing potentials. This was suggested as due to the increasing formation of oxygenated species on the electrode surface with potential, which in turn is more efficient than the increase of water content in the electrolyte. Altogether, these results were interpreted as an evidence of a Langmuir-Hinshelwood step involving oxygenated species as one of the adsorbed partners. (author)

Spectroscopic study and enhanced thermostability of combustion-derived BaMgAl10O17:Eu2+ blue phosphors for solid-state lighting

Science.gov (United States)

Pradal, Nathalie; Potdevin, Audrey; Chadeyron, Geneviève; Bonville, Pierre; Caillier, Bruno; Mahiou, Rachid

2017-02-01

Blue-emitting BaMgAl10O17:Eu2+ (BAM:Eu), suitable for applications in a next generation of Hg-free lamps based on UV LEDs, was prepared by a microwave induced solution combustion synthesis, using urea as combustion fuel and nitrates as oxidizers. Purity control of the as-synthesized blue phosphor was undertaken by a washing step followed by a reduction one. Structural and morphological properties of the outcoming phosphors have been considered. Synthesis process allows producing a well-crystallized and nanostructured BAM phase within only few minutes. The influence of reduction treatment on the relative amounts of Eu2+/Eu3+ in our samples has been investigated through an original study by magnetization and Mössbauer spectroscopy. Furthermore, a complete optical study has been carried out and allowed us to determine the europium localization in the three possible sites in BAM matrix. The percentage of Eu2+ increased twofold after the reduction treatment, entailing an increase in the luminescence efficiency upon UV excitation. Finally, temperature-dependent luminescence of combustion-derived powders has been studied till 170 °C and compared to that of commercial BAM:Eu. MISCS-derived phosphors present a higher thermal stability than commercial one: whereas the emission efficiency of this last was reduced by 64%, the one of combustion-derived BAM:Eu experienced an only 12% decline. Furthermore, while commercial BAM suffered from a severe blue-shift with increasing temperature, our phosphors keep its color quality with a good stability of the photometric parameters.

Enantioselective Synthesis of α-Mercapto-β-amino Esters via Rh(II)/Chiral Phosphoric Acid-Cocatalyzed Three-Component Reaction of Diazo Compounds, Thiols, and Imines.

Science.gov (United States)

Xiao, Guolan; Ma, Chaoqun; Xing, Dong; Hu, Wenhao

2016-12-02

An enantioselective method for the synthesis of α-mercapto-β-amino esters has been developed via a rhodium(II)/chiral phosphoric acid-cocatalyzed three-component reaction of diazo compounds, thiols, and imines. This transformation is proposed to proceed through enantioselective trapping of the sulfonium ylide intermediate generated in situ from the diazo compound and thiol by the phosphoric acid-activated imine. With this method, a series of α-mercapto-β-amino esters were obtained in good yields with moderate to good stereoselectivities.

Determination of elemental impurities in phosphoric acid by INAA employing a novel method of phosphate precipitation

Czech Academy of Sciences Publication Activity Database

Kameník, Jan; Amsil, H.; Kučera, Jan

2014-01-01

Roč. 2014, AUG (2014), s. 3455 ISSN 1588-2780 R&D Projects: GA ČR(CZ) GBP108/12/G108; GA MŠk(XE) LM2011019 Institutional support: RVO:61389005 Keywords : instrumental neutron activation analysis * phosphoric acid * elemental impurities * isothermal distillation Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders

Spectrophotometric and potentiometric studies of oxidation of Mo(III) by Mo(VI) in phosphoric acid medium

International Nuclear Information System (INIS)

Kumar, Arvind; Verma, G.S.P.

1975-01-01

Oxidation of Mo(III) (green) by Mo(VI) in an inert atmosphere and in orthophosphoric acid medium at various acid concentrations is reported. Potentiometric and spectrophotometric data suggest that oxidation of Mo(III) proceeds to Mo(V) through a binuclear species Mo(III) Mo(IV) absorbing at 400 nm. The formation of this species is facilitated at high acid concentrations. It is further found that quantitative conversion of Mo(III) into Mo(V) takes place at fairly high acid concentrations. In high phosphoric acid concentrations, solution of Mo(III) has been found to be oxidized to Mo(VI) by air and hence this can be used as a good oxygen absorber. (author)

Evaluation of two processes for the production of phosphoric acid in pilot scale

International Nuclear Information System (INIS)

Santos Benedetto, J. dos.

1984-01-01

Two processes for the production of phosphoric acid, based on dihydrate route and hemihydrate route, have been evaluated. The processes were tested in a pilot plant using the concentrate obtained from phosphorus-uraniferous mineral from Itataia mines (CE, Brazil). Results were evaluated from the data obtained from phosphorus and uranium solubilizations. Also presented, although in a summarised way, are the description of the construction of the pilot plants and the analytical methods for the follow-up of processes. (Author) [pt

Determination of elemental impurities in phosphoric acid by INAA employing a novel method of phosphate precipitation

Czech Academy of Sciences Publication Activity Database

Kameník, Jan; Amsil, H.; Kučera, Jan

2015-01-01

Roč. 304, APR (2015), s. 157-162 ISSN 0236-5731 R&D Projects: GA ČR(CZ) GBP108/12/G108; GA MŠk LM2011019 Institutional support: RVO:61389005 Keywords : instrumental neutron activation analysis * phosphoric acid * elemental impurities * isothermal distillation Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 0.983, year: 2015

Thermal Effect on the phosphoric Acid Impregnated Activated Carbon Fiber and Adsorption Properties Toward Isoprene

Energy Technology Data Exchange (ETDEWEB)

Hwang, Taek Sung; Lee, Jin Hyok; Kang, Kyung suk [Department of Chemical Engineering, College of Engineering, Chungnam National University, Taejon (Korea); Kim, Kwang Young [Ace Lab. Co. Ltd. Taejon (Korea); Rhee, Moon Soo [Korea Ginseng and Tobacoo Research Institute, Taejon (Korea)

2001-05-01

To introduce chemisorption property and improve adsorption capacities for isoprene, ACF (Activated Carbon Fiber) was impregnated by phosphoric acid. As the impregnated ACF was dried by programmed temperature from 300 degree C to 500 degree C, degree of impregnation, surface area, thermal stability and adsorption properties for isoprene were observed. The degree of impregnation of the ACF, dried at the 400 degree C, was 12.7 w/w% and surface area was 1148 m{sup 2}/g. Over the temperature range of 450 degree C to 700 degree C, there was one-step thermal degradation by the thermal decomposition of phosphonyl group. The adsorption rate of phosphoric acid on the impregnated ACF, which was dried at 400 degree C, was the fastest. The breakthrough time of ACF that was dried at 400 degree C was 18 min., and its adsorption capacity improved roughly 7.2 times in comparison to the pure ACF. In addition, it was observed the adsorption properties persisted even after the regeneration. The adsorption efficiency of regenerated ACF was 66 percent compared to the unused impregnated ACF. 21 refs., 7 figs., 3 tabs.

Reaction kinetics of free fatty acids esterification in palm fatty acid distillate using coconut shell biochar sulfonated catalyst

Science.gov (United States)

Hidayat, Arif; Rochmadi, Wijaya, Karna; Budiman, Arief

2015-12-01

Recently, a new strategy of preparing novel carbon-based solid acids has been developed. In this research, the esterification reactions of Palm Fatty Acid Distillate (PFAD) with methanol, using coconut shell biochar sulfonated catalyst from biomass wastes as catalyst, were studied. In this study, the coconut shell biochar sulfonated catalysts were synthesized by sulfonating the coconut shell biochar using concentrated H2SO4. The kinetics of free fatty acid (FFA) esterification in PFAD using a coconut shell biochar sulfonated catalyst was also studied. The effects of the mass ratio of catalyst to oil (1-10%), the molar ratio of methanol to oil (6:1-12:1), and the reaction temperature (40-60°C) were studied for the conversion of PFAD to optimize the reaction conditions. The results showed that the optimal conditions were an methanol to PFAD molar ratio of 12:1, the amount of catalyst of 10%w, and reaction temperature of 60°C. The proposed kinetic model shows a reversible second order reaction and represents all the experimental data satisfactorily, providing deeper insight into the kinetics of the reaction.

Recovery of uranium from phosphoric acid medium by polymeric composite beads encapsulating organophosphorus extractants

Energy Technology Data Exchange (ETDEWEB)

Singh, D.K.; Yadav, K.K.; Varshney, L.; Singh, H. [Bhabha Atomic Research Centre, Mumbai 400 085 (India)

2013-07-01

The present study deals with the preparation and evaluation of the poly-ethersulfone (PES) based composite beads encapsulating synergistic mixture of D2EHPA and Cyanex 923 (at 4:1 mole ratio) for the separation of uranium from phosphoric acid medium. SEM was used for the characterization of the composite materials. Addition of 1% PVA (polyvinyl alcohol) improved the internal morphology and porosity of the beads. Additionally, microscopic examination of the composite bead confirmed central coconut type cavity surrounded by porous polymer layer of the beads through which exchange of metal ions take place. Effect of various experimental variables including aqueous acidity, metal ion concentration in aqueous feed, concentration of organic extractant inside the beads, extractant to polymer ratio, liquid to solid (L/S) ratio and temperature on the extraction of uranium was studied. Increase in acidity (1-6 M), L/S ratio (1- 10), metal ion concentration (0.2-3 g/L U{sub 3}O{sub 8}) and polymer to extractant ratio (1:4 -1:10) led to decrease in extraction of uranium. At 5.5 M (comparable to wet process phosphoric acid concentration) the extraction of uranium was about 85% at L/S ratio 5. Increase in extractant concentration inside the bead resulted in enhanced extraction of metal ion. Increase in temperature in the range of 30 to 50 Celsius degrees increased the extraction, whereas further increase to 70 C degrees led to the decrease in extraction of uranium. Amongst various reagents tested, stripping of uranium was quantitative by 12% Na{sub 2}CO{sub 3} solution. Polymeric beads were found to be stable and reusable up-to 10 cycles of extraction/stripping. (authors)

Research and development of a phosphoric acid fuel cell/battery power source integrated in a test-bed bus. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-30

This project, the research and development of a phosphoric acid fuel cell/battery power source integrated into test-bed buses, began as a multi-phase U.S. Department of Energy (DOE) project in 1989. Phase I had a goal of developing two competing half-scale (25 kW) brassboard phosphoric acid fuel cell systems. An air-cooled and a liquid-cooled fuel cell system were developed and tested to verify the concept of using a fuel cell and a battery in a hybrid configuration wherein the fuel cell supplies the average power required for operating the vehicle and a battery supplies the `surge` or excess power required for acceleration and hill-climbing. Work done in Phase I determined that the liquid-cooled system offered higher efficiency.

(Di­methyl­phosphor­yl)methanaminium hydrogen oxalate–oxalic acid (2/1)

OpenAIRE

Bialek, Sebastian; Clemens, Rebecca; Reiss, Guido J.

2014-01-01

The reaction of (di­methyl­phosphor­yl)methanamine (dpma) with oxalic acid in ethanol yielded the title solvated salt, C3H11NOP+·C2HO4 −·0.5C2H2O4. Its asymmetric unit consists of one dpmaH+ cation, one hydrogen oxalate anion and a half-mol­ecule of oxalic acid located around a twofold rotation axis. The H atom of the hydrogen oxalate anion is statistically disordered over two positions that are trans to each other. The hydrogen oxalate monoanion is not planar (bend angle ∼16°) whereas the ox...

Experiences from Swedish demonstration projects with phosphoric acid fuel cells; Erfarenheter fraan svenska demonstrationsprojekt med fosforsyrabraensleceller

Energy Technology Data Exchange (ETDEWEB)

Carlsson, Per [Sycon Energikonsult AB, Stockholm (Sweden); Sarkoezi, Laszlo [Vattenfall Utveckling AB, Stockholm (Sweden)

1999-10-01

In Sweden, there are today two phosphoric acid fuel cells installed, one PC25A which have been in operation in more than 4 years, and one PC25C which have been in operation for two years. The aim with this project has been two compare operation characteristics, performance, and operation experiences for these two models.

Re-processing CRT phosphors for mercury-free applications

International Nuclear Information System (INIS)

Dexpert-Ghys, Jeannette; Regnier, Sophie; Canac, Sophie; Beaudette, Tristan; Guillot, Philippe; Caillier, Bruno; Mauricot, Robert; Navarro, Julien; Sekhri, Salem

2009-01-01

This study is part of an operation in the framework of treatment and revalorization of IEEE (Informatics, Electronics and related) wastes. It aims to recover the active phosphors in cathode ray tubes (CRTs) and to re-cycle these powders by appropriate treatments as phosphors for mercury-free applications such as plasma display panels, flat lamps, advertising and lighting. The studied waste comes from a large panel of CRTs from any supplier. Several thermo-chemical treatments have been investigated. The removal of zinc sulfide-based phosphors and the recovery of a red phosphor Y 2 O 3 :Eu 3+ has been achieved by one (basic attack) route. The photoluminescence efficiency under VUV excitation of the obtained powders is at most 30% that of a commercial phosphor. The second route (acid attack) appears less promising. It has been established that silicate-based impurities could prevent isolating the yttrium based phosphor.

Re-processing CRT phosphors for mercury-free applications

Energy Technology Data Exchange (ETDEWEB)

Dexpert-Ghys, Jeannette, E-mail: jdexpert@cemes.f [CEMES, 29 rue Jeanne Marvig, BP 94347, 31055 Toulouse cedex 4 (France); Regnier, Sophie; Canac, Sophie [ICAM, 75 avenue de Grande Bretagne, 31300 Toulouse (France); Beaudette, Tristan; Guillot, Philippe; Caillier, Bruno [DPHE, Universite Jean Francois Champollion, place de Verdun, 81012 Albi cedex 9 (France); Mauricot, Robert; Navarro, Julien [CEMES, 29 rue Jeanne Marvig, BP 94347, 31055 Toulouse cedex 4 (France); Sekhri, Salem [ENVOI, Cheminement Glueck, 31100 Toulouse (France)

2009-12-15

This study is part of an operation in the framework of treatment and revalorization of IEEE (Informatics, Electronics and related) wastes. It aims to recover the active phosphors in cathode ray tubes (CRTs) and to re-cycle these powders by appropriate treatments as phosphors for mercury-free applications such as plasma display panels, flat lamps, advertising and lighting. The studied waste comes from a large panel of CRTs from any supplier. Several thermo-chemical treatments have been investigated. The removal of zinc sulfide-based phosphors and the recovery of a red phosphor Y{sub 2}O{sub 3}:Eu{sup 3+} has been achieved by one (basic attack) route. The photoluminescence efficiency under VUV excitation of the obtained powders is at most 30% that of a commercial phosphor. The second route (acid attack) appears less promising. It has been established that silicate-based impurities could prevent isolating the yttrium based phosphor.

Method of cleansing and refining of liquid hydrocarbons and derivatives of hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Hahn, C A; Nielsen, H

1934-10-11

A process is described for cleaning and refining liquid hydrocarbons and derivatives by utilization of acids, followed by washing partly with a basic solution, partly with clean water. The process is characterized by using, in connection with the acid solutions mentioned, a strong solution of a mixture of sulfuric acid and phosphoric acid.

Quality parameters evaluation for the determination of available phosphorous in soils

International Nuclear Information System (INIS)

Garcia Galvis, John Brynner; Ballesteros, Maria Ines

2006-01-01

There are some colorimetric procedures for determining available phosphorous in soils, and phosphorous is evaluated by means of a blue complex (phosphomolybdic acid); in one of the methods, color appear when ascorbic acid is used as reductor agent, and in the other when stannous chloride is used. Both methods use the same extractive solution bray i i due to its good response for acid soil cultures, like most Colombian soils are. When the two methodologies were compared it was found that the most sensible method and with the best limit of detection and quantification was the one that uses ascorbic acid, antimonious and potassium tartrate. Its variation coefficients and standard deviation were lower, and for this reason it is considered as the most precise method for phosphorous determination

Purification of Industrial Phosphoric Acid using Silica Produced from Rice Husk (Part 1)

International Nuclear Information System (INIS)

Gad, H.M.H.; Awwad, N.S.; El-Khalafawy, A.; Daifullah, A.A.M.; El-Reefy, S.A.; Aly, H.F.

2008-01-01

In this work, silica was extracted from rice husk (RH) by different techniques and used for removal of some heavy metals from industrial phosphoric acid. The data obtained, showed that removal of Cu(II), Cd(II) and Pb(II) is efficient when the silica used is obtained by acidic treatment, while the removal of Fe(III) and Zn(II) is efficient when the silica used was obtained by alkaline treatment of RH. On the other hand, if silica used is obtained from rice husk ash (RHA) it was found more efficient for the removal of Mn. In all cases, the concentration of silica has been characterized by UV-Spectrophotometry. FTIR, SEM and EDX were used for predication of sorption mechanism

The extraction of uranium from wet process phosphoric acid using a liquid surfactant membrane system

International Nuclear Information System (INIS)

Dickens, N.; Davies, G.A.

1984-01-01

A liquid membrane extraction process is examined for the extraction of uranium from wet process phosphoric acid. Uranium is present in the acid in concentrations up to 100 ppm which in principle makes it ideal for treatment with a membrane process. The membrane system studied is based on extraction using DEHPA-TOPO reagents which are contained within the organic phase of a water in oil emulsion. Formulations of the emulsion membrane system have been studied, the limitations of acid temperature, P 2 O 5 concentration and solid dispersed impurities in the acid have been studied in laboratory batch experiments and in a continuous pilot plant unit capable of treating 5l of concentrated acid per minute. Data from the pilot plant work has been used to develop a flowsheet for a commercial unit based on this process. (author)

Use of a pulsed column with discs and crowns for uranium extraction from phosphoric acid

International Nuclear Information System (INIS)

1982-04-01

The physico-chemistry of the system phosphoric acid-uranium-dioctylpyrophosphoric acid is studied for the determination of analytical methods and extraction parameters (oxidation state of uranium and iron, phosphorus concentration, extractant concentration). Extraction is then realized on a pilot scale with a liquid-liquid extraction column 4m high and of 50 mm in diameter with a column packing made of discs and crowns. Column efficiency is evaluated by studying uranium transfer as a function of operating conditions. The results obtained are extrapolated to an industrial scale and a comparative economic evaluation is made between a pulsed column and a mixer-settler [fr

Synergic extraction of some lanthanide and actinide elements by a mixture of bis(2-ethyl hexyl) phosphoric acid and dinonylnapthalene - sulfonic acid in aromatic diluents

International Nuclear Information System (INIS)

Raieh, M.A.; El-Dessouky, M.M.

1985-01-01

Extraction of lanthanides and actinides were found to be synergetically enhanced by a mixture of bis(2-ethyl hexyl) phosphoric acid (HA) and dinonylnaphthalene sulfonic acid (HD) in aromatic diluents covering a wide range of dielectric constants. The main extracted species is found to be MAsub(2)Hsub(m-1)Dsub(m). Experimental results indicate that the extraxtion mechanism is governed by the extraction of HD in the organic phase. (author)

Facile fabrication of siloxane @ poly (methylacrylic acid) core-shell microparticles with different functional groups

Energy Technology Data Exchange (ETDEWEB)

Zhao, Zheng-Bai; Tai, Li; Zhang, Da-Ming; Jiang, Yong, E-mail: yj@seu.edu.cn [Southeast University, School of Chemistry and Chemical Engineering (China)

2017-02-15

Siloxane @ poly (methylacrylic acid) core-shell microparticles with functional groups were prepared by a facile hydrolysis-condensation method in this work. Three different silane coupling agents 3-methacryloxypropyltrimethoxysilane (MPS), 3-triethoxysilylpropylamine (APTES), and 3-glycidoxypropyltrimethoxysilane (GPTMS) were added along with tetraethoxysilane (TEOS) into the polymethylacrylic acid (PMAA) microparticle ethanol dispersion to form the Si@PMAA core-shell microparticles with different functional groups. The core-shell structure and the surface special functional groups of the resulting microparticles were measured by transmission electron microscopy and FTIR. The sizes of these core-shell microparticles were about 350–400 nm. The corresponding preparation conditions and mechanism were discussed in detail. This hydrolysis-condensation method also could be used to functionalize other microparticles which contain active groups on the surface. Meanwhile, the Si@PMAA core-shell microparticles with carbon-carbon double bonds and amino groups have further been applied to prepare hydrophobic coatings.

Facile fabrication of siloxane @ poly (methylacrylic acid) core-shell microparticles with different functional groups

International Nuclear Information System (INIS)

Zhao, Zheng-Bai; Tai, Li; Zhang, Da-Ming; Jiang, Yong

2017-01-01

Siloxane @ poly (methylacrylic acid) core-shell microparticles with functional groups were prepared by a facile hydrolysis-condensation method in this work. Three different silane coupling agents 3-methacryloxypropyltrimethoxysilane (MPS), 3-triethoxysilylpropylamine (APTES), and 3-glycidoxypropyltrimethoxysilane (GPTMS) were added along with tetraethoxysilane (TEOS) into the polymethylacrylic acid (PMAA) microparticle ethanol dispersion to form the Si@PMAA core-shell microparticles with different functional groups. The core-shell structure and the surface special functional groups of the resulting microparticles were measured by transmission electron microscopy and FTIR. The sizes of these core-shell microparticles were about 350–400 nm. The corresponding preparation conditions and mechanism were discussed in detail. This hydrolysis-condensation method also could be used to functionalize other microparticles which contain active groups on the surface. Meanwhile, the Si@PMAA core-shell microparticles with carbon-carbon double bonds and amino groups have further been applied to prepare hydrophobic coatings.

Separation of transuranium elements from high-level waste by extraction with diisodecyl phosphoric acid

International Nuclear Information System (INIS)

Morita, Y.; Kubota, M.; Tani, S.

1991-01-01

Separation of transuranic elements (TRU) by extraction with diisodecyl phosphoric acid (DIDPA) has been studied to develop a partitioning process for high-level waste (HLW). In the present study, experiments of counter-current continuous extraction and back-extraction using a miniature mixer-settler were carried out to find the optimum process condition for the separation of Np initially in the pentavalent state and to examine the extraction behaviors of fission and corrosion products. (J.P.N.)

Determination of Water Vapor Pressure Over Corrosive Chemicals Versus Temperature Using Raman Spectroscopy as Exemplified with 85.5% Phosphoric Acid

DEFF Research Database (Denmark)

Rodier, Marion; Li, Qingfeng; Berg, Rolf W.

2016-01-01

A method to determine the water vapor pressure over a corrosive substance was developed and tested with 85.5 ± 0.4% phosphoric acid. The water vapor pressure was obtained at a range of temperatures from ∼25 ℃ to ∼200 ℃ using Raman spectrometry. The acid was placed in an ampoule and sealed...... with a reference gas (either hydrogen or methane) at a known pressure (typically ∼0.5 bar). By comparing the Raman signals from the water vapor and the references, the water pressure was determined as a function of temperature. A considerable amount of data on the vapor pressure of phosphoric acid are available...... in the literature, to which our results could successfully be compared. A record value of the vapor pressure, 3.40 bar, was determined at 210 ℃. The method required a determination of the precise Raman scattering ratios between the substance, water, and the used reference gas, hydrogen or methane. In our case...

Utilization of porous carbons derived from coconut shell and wood in natural rubber

Science.gov (United States)

The porous carbons derived from cellulose are renewable and environmentally friendly. Coconut shell and wood derived porous carbons were characterized with elemental analysis, ash content, x-ray diffraction, infrared absorbance, particle size, surface area, and pore volume. The results were compared...

Oxygen Reduction on Gas-Diffusion Electrodes for Phosphoric Acid Fuel Cells by a Potential Decay Method

DEFF Research Database (Denmark)

Li, Qingfeng; Gang, Xiao; Hjuler, Hans Aage

1995-01-01

The reduction of gaseous oxygen on carbon supported platinum electrodes has been studied at 150 degrees C with polarization and potential decay measurements. The electrolyte was either 100 weight percent phosphoric acid or that acid with a fluorinated additive, potassium perfluorohexanesulfonate ......6F13SO3K). The pseudo-Tafel curves of the overpotential vs. log (ii(L)/(i(L) - i)) show a two-slope behavior, probably due to different adsorption mechanisms. The potential relaxations as functions of log (t + tau) and log (-d eta/dt) have been plotted. The variations of these slopes...

Recovery of fluorine, uranium, and rare earth metal values from phosphoric acid by-product brine raffinate

International Nuclear Information System (INIS)

Wamser, C.A.; Bruen, C.P.

1976-01-01

A method for recovering substantially all of the fluorine and uranium values and at least 90 percent of the rare earth metal values from brine raffinate obtained as by-product in the production of phosphoric acid by the hydrochloric acid decomposition of tricalcium phosphate minerals is described. A basically reacting compound is added to the brine raffinate to effect a pH 9 or greater, whereby fluorine, uranium and rare earth metal values are simultaneously precipitated. These values may then be separately recovered from the precipitate by known processes

Determination of phosphorus using derivative neutron activation

International Nuclear Information System (INIS)

Scindia, Y.M.; Nair, A.G.C.; Reddy, A.V.R.; Manohar, S.B.

2002-01-01

For the determination of phosphorus in different matrices, the derivative neutron activation analysis is especially applicable to aqueous samples, since the conventional neutron activation analysis is not useful for the determination of phosphorus. Phosphorus when reacted with ammonium molybdate 4 hydrate and ammonium metavanadate forms molybdo vanado phosphoric acid. This complex is preconcentrated by extracting into methyl isobutyl ketone. The organic phase containing the molybdo vanado phosphoric acid is neutron activated and the phosphorus is determined through the activation product of 52 V. Preparation of this complex, its stoichiometry, application to trace level determination of phosphorus and improved detection limit are discussed. This method was applied for the analysis of industrial effluent samples. (author)

Synthesis of Fluorite (CaF2 Crystal from Gypsum Waste of Phosphoric Acid Factory in Silica Gel

Directory of Open Access Journals (Sweden)

Mohammad Misbah Khunur

2012-06-01

Full Text Available This paper report the synthesis and characterization of fluorite single crystal prepared from gypsum waste of phosphoric acid production in silica gel. Instead of its high calcium, gypsum was used to recycle the waste which was massively produces in the phosphoric acid production. The gypsum waste, the raw material of CaCl2 supernatant, was dissolved in concentrated HCl and then precipitated as calcium oxalate (CaC2O4 by addition of ammonium oxalate. The CaCl2 was obtained by dissolving the CaC2O4 with HCl 3M. The crystals were grown at room temperature in silica gel and characterized by AAS, FTIR and powder XRD. The optimum crystal growth condition, which is pH of gel, CaCl2 concentration and growth time, were investigated. The result shows that at optimum condition of pH 5.80, CaCl2 concentrations of 1.2 M, and growth time of 144 hours, colorless crystals with the longest size of 3 mm, were obtained (72.57%. Characterization of the synthesized crystal by AAS indicates that the obtained crystal has high purity. Meanwhile, analysis by FTIR spectra shows a Ca–F peak at 775 cm-1, and powder-XRD analysis confirms that the obtained crystal was fluorite (CaF2. © 2012 BCREC UNDIP. All rights reservedReceived: 11st April 2012; Revised: 4th June 2012; Accepted: 13rd June 2012[How to Cite: M.M. Khunur, A. Risdianto, S. Mutrofin, Y.P. Prananto. (2012. Synthesis of Fluorite (CaF2 Crystal from Gypsum Waste of Phosphoric Acid Factory in Silica Gel. Bulletin of Chemical Reaction Engineering & Catalysis, 7 (1: 71-77.  doi:10.9767/bcrec.7.1.3171.71-77 ][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.1.3171.71-77 ] | View in 

Performance Degradation Tests of Phosphoric Acid Doped Polybenzimidazole Membrane Based High Temperature Polymer Electrolyte Membrane Fuel Cells

DEFF Research Database (Denmark)

Zhou, Fan; Araya, Samuel Simon; Grigoras, Ionela

2015-01-01

Degradation tests of two phosphoric acid (PA) doped PBI membrane based HT-PEM fuel cells were reported in this paper to investigate the effects of start/stop and the presence of methanol in the fuel to the performance degradation of the HT-PEM fuel cell. Continuous tests with pure dry H2 and meth...

Studies on the solvent extraction behaviour of Pu(IV) from nitric acid, nitric-perchloric acid and hydrochloric acids, by di,2-ethylhexyl phosphoric acid (HDEHP)

International Nuclear Information System (INIS)

Phal, D.G.; Kannan, S.K.; Ramakrishna, V.V.

1994-01-01

Extraction of plutonium (IV) from aqueous nitric acid, nitric-perchloric acid and hydrochloric acids by di,2-ethylhexyl phosphoric acid, the dimeric form of which is represented as H 2 Y 2 , in different diluents (dodecane, toluene and chloroform) was investigated. The composition of the extracted Pu(IV) species were found to be Pu(NO 3 ) 2 (HY) 2 , Pu(NO 3 )(ClO 4 )(HY 2 ) 2 , PuClY(HY 2 ) 2 and PuCl 2 (HY 2 ) 2 from nitric, nitric-perchloric and hydrochloric acids respectively, the last one being pre-dominant at high aqueous acidities (i.e. 5M HCl). Synergic enhancement in the extraction of Pu(IV) from different aqueous media, by the addition of thenoyltrifluoroacetone (HTTA) to HDEHP was also investigated and was attributed to the formation and extraction of the species PuX(TTA)(HY 2 ) 2 , and Pu(TTA) 2 (HY 2 ) 2 where X=Cl - or NO 3 - . The addition of the neutral extractant TOPO to H 2 Y 2 also resulted in synergism. The possible equilibria in these systems were inferred and the corresponding equilibrium constants determined. (author). 24 refs., 10 figs., 10 tabs

Electrochemical characterization of supercapacitors based on carbons derived from coffee shells

Energy Technology Data Exchange (ETDEWEB)

Jisha, M.R.; Hwang, Yun Ju [Department of Hydrogen and Fuel cells Engineering, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Shin, Jae Sun [School of Nanosemiconductor display, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Nahm, Kee Suk [Department of Hydrogen and Fuel cells Engineering, Chonbuk National University and School of Chemical Engineering and Technology, Jeonju 561-756 (Korea, Republic of)], E-mail: nahmks@chonbuk.ac.kr; Prem Kumar, T.; Karthikeyan, K.; Dhanikaivelu, N.; Kalpana, D.; Renganathan, N.G.; Stephan, A. Manuel [Central Electro Chemical Research Institute, Karaikudi 630006 (India)

2009-05-15

Carbons derived by pyrolysis of coffee shells treated with ZnCl{sub 2} were used as electrode materials in symmetric electrochemical supercapacitors. Scanning electron microscopy showed that the carbon from the porogen-free shells show a flake-like structure, while those from the ZnCl{sub 2}-treated coffee shells have a loose, disjointed structure with no definite shape. X-ray diffraction studies indicated the presence of small domains of coherent and parallel stacking of the graphene sheets. The average surface area of the carbon was 842 m{sup 2} g{sup -1}, with an average micropore area of 400 m{sup 2} g{sup -1}. Cyclic voltammetric studies suggested a specific capacitance of about 150 F g{sup -1}. Self-discharge studies on the devices showed a large retention time.

Microbial Degradation of Lobster Shells to Extract Chitin Derivatives for Plant Disease Management

Directory of Open Access Journals (Sweden)

Gayathri Ilangumaran

2017-05-01

Full Text Available Biodegradation of lobster shells by chitinolytic microorganisms are an environment safe approach to utilize lobster processing wastes for chitin derivation. In this study, we report degradation activities of two microbes, “S223” and “S224” isolated from soil samples that had the highest rate of deproteinization, demineralization and chitinolysis among ten microorganisms screened. Isolates S223 and S224 had 27.3 and 103.8 protease units mg-1 protein and 12.3 and 11.2 μg ml-1 of calcium in their samples, respectively, after 1 week of incubation with raw lobster shells. Further, S223 contained 23.8 μg ml-1 of N-Acetylglucosamine on day 3, while S224 had 27.3 μg ml-1 on day 7 of incubation with chitin. Morphological observations and 16S rDNA sequencing suggested both the isolates were Streptomyces. The culture conditions were optimized for efficient degradation of lobster shells and chitinase (∼30 kDa was purified from crude extract by affinity chromatography. The digested lobster shell extracts induced disease resistance in Arabidopsis by induction of defense related genes (PR1 > 500-fold, PDF1.2 > 40-fold upon Pseudomonas syringae and Botrytis cinerea infection. The study suggests that soil microbes aid in sustainable bioconversion of lobster shells and extraction of chitin derivatives that could be applied in plant protection.

Encapsulation of strontium aluminate phosphors to enhance water resistance and luminescence

International Nuclear Information System (INIS)

Zhu Yong; Zeng Jianghua; Li Wenyu; Xu Li; Guan Qiu; Liu Yingliang

2009-01-01

Strontium aluminate SrAl 2 O 4 :Eu 2+ ,Dy 3+ phosphors are chemically unstable against water or even moisture. To enhance the water resistance of the phosphors, an encapsulation was performed by direct surface reactions with phosphoric acid (H 3 PO 4 ). The morphology, surface structure, surface element composition, water resistance, luminescence, and photoacoustic spectrum of the phosphors before and after encapsulation were discussed. Experimental results showed that phosphors were perfectly encapsulated by amorphous layers in nanoscale and crystalline layers in microscale under different conditions. The water resistance of phosphors was greatly enhanced by the two types of layer. More importantly, the amorphous layers enhanced the luminescence of phosphors markedly. The possible mechanism for the enhancements was also proposed.

Structure and expression of an unusually acidic matrix protein of pearl oyster shells

International Nuclear Information System (INIS)

Tsukamoto, Daiki; Sarashina, Isao; Endo, Kazuyoshi

2004-01-01

We report identification and characterization of the unusually acidic molluscan shell matrix protein Aspein, which may have important roles in calcium carbonate biomineralization. The Aspein gene (aspein) encodes a sequence of 413 amino acids, including a high proportion of Asp (60.4%), Gly (16.0%), and Ser (13.2%), and the predicted isoelectric point is 1.45; this is the most acidic of all the molluscan shell matrix proteins sequenced so far, or probably even of all known proteins on earth. The main body of Aspein is occupied by (Asp) 2-10 sequences punctuated with Ser-Gly dipeptides. RT-PCR demonstrated that the transcript of aspein is expressed at the outer edge of the mantle, corresponding to the calcitic prismatic layer, but not at the inner part of the mantle, corresponding to the aragonitic nacreous layer. Our findings and previous in vitro experiments taken together suggest that Aspein is responsible for directed formation of calcite in the shell of the pearl oyster Pinctada fucata

Progress of research on the adsorption of chitosan and its derivatives to uranium

International Nuclear Information System (INIS)

Wang Caixia; Liu Yunhai; Hua Rong; Pang Cui; Wang Yong

2010-01-01

This paper has summarized the study on the adsorption of chitosan and its derivatives to uranium in recent years at home and abroad. It was found that the derivatives can be serine-type chitosan, methyl phosphoric acid modified chitosan, 3,4-dihydroxy benzoic acid-type chitosan, chitosan with 3,4-dihydroxybenzoic acid moiety, chitosan resin possessing a phenylarsonic acid moiety, quadrol modified chitosan, chitosan modified with molecular imprinting technique, polyacrylamide hydrogel, chitosan-coated perlite and so on. The application vista of chitosan and its derivatives to Absorpt uranium in water has been prospected. (authors)

Determination of the activity concentration of {sup 230}Th in phosphoric acids produced in Brazil; Determinação da concentração de atividade de {sup 230}Th em ácidos fosfóricos produzidos no Brasil

Energy Technology Data Exchange (ETDEWEB)

Taddei, M.H.T.; Ferreira, M.T.; Fukuma, H.T.; Xavier, T.T.; Sousa, F.V.T.S., E-mail: tatianattx@gmail.com [Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Laboratorio de Pocos de Caldas. Radioquimica

2017-07-01

The high uranium phosphate rock from Itataia, Brazil, was processed using the wet route in the dihydrate system to manufacture phosphoric acid. The uranium contained in phosphoric acid was recovered by the solvent extraction technique. The distribution of the long half-life radionuclides from the decay series of {sup 238}U and {sup 232}Th were evaluated in these processes. The {sup 26}Ra, {sup 228}Ra and {sup 210}Pb radionuclides were found predominantly in phosphogypsum, while the isotopes of {sup 228}Th, {sup 230}Th and {sup 232}Th predominated in phosphoric acid after extracting uranium. The main concern in the commercialization of phosphoric acid that will be produced in the Itataia plant is in relation to the content of {sup 230}Th. This work determined the content of these radionuclides in phosphoric acid from different locations in the country in order to compare.

Photoluminescence emission of nanoporous anodic aluminum oxide films prepared in phosphoric acid

Science.gov (United States)

2012-01-01

The photoluminescence emission of nanoporous anodic aluminum oxide films formed in phosphoric acid is studied in order to explore their defect-based subband electronic structure. Different excitation wavelengths are used to identify most of the details of the subband states. The films are produced under different anodizing conditions to optimize their emission in the visible range. Scanning electron microscopy investigations confirm pore formation in the produced layers. Gaussian analysis of the emission data indicates that subband states change with anodizing parameters, and various point defects can be formed both in the bulk and on the surface of these nanoporous layers during anodizing. PMID:23272786

Chemical process for recovery of uranium values contained in phosphoric mineral lixivia

International Nuclear Information System (INIS)

Conceicao, E.L.H. da; Awwal, M.A.; Coelho, S. V.

1980-01-01

A recovery process of uranium values from phosporic mineral lixivia for obtaining uranio oxide concentrate adjusted to specifications of purity for its commercialization the process consists of the adjustment of electromotive force of lixiviem to suitable values for uranium extraction, extraction with organic solvent containing phosphoric acid ester and oxidant reextraction from this solvent with phosphoric acid solution, suggesting a new solvent extraction containing synergetic mixture of di-2-ethyl hexyl phosphoric acid and tri-octyl phosphine, leaching this solvent with water and re-extraction/precipitation with ammonium carbonate solution, resulting in the formation of uranyl tricarbonate and ammonium, that by drying and calcination gives the uranium oxide with purity degree for commercialization. (M.C.K.) [pt

Uranium problem in production of wet phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Gorecka, H; Gorecki, H [Politechnika Wroclawska (Poland)

1980-01-01

The balance of the uranium in the wet dihydrate method was presented. This balance shows that a large quantity of the uranium compounds shift from mineral phosphate rock to liquid phase of decomposition pulp (about 70-85% U) and the rest moves to phosphogypsum (about 15-25% U). The contents of uranium in phosphate rock imported for our country and in products and by-products of the fertilizer industry, were determined. Concentration of uranium in the phosphogypsum is dependent on the type of mineral rock and the process of phosphogypsum crystallization. Analysis of the uranium contents in phosphogypsum samples and results of the sedimentation analysis indicated influence of the specific surface of phosphogypsum crystals on the uranium concentration. Investigation of the sets of samples obtained in the industrial plant proved that phosphogypsum cake washed counter-currently on the filter contained from 10 to 20 ..mu..g U/g. The radioactivity of these samples fluctuated from 35 to 60 pCi/g. Using solution sulphuric acid of concentration in range 2-4% by weight H/sub 2/SO/sub 4/ to washing and repulpation of the phosphogypsum enables to reduce its radioactivity to level below 25 pCi/g. This processing makes possible to utilize this waste material in the building industry. Extraction of uranium from the wet phosphoric acid using kerosen solution of the reaction product between octanol -1 and phosphorus pentaoxide showed possibility to recover over 80% of uranium contained in phosphate rock.

Effect of surface acidic oxides of activated carbon on adsorption of ammonia.

Science.gov (United States)

Huang, Chen-Chia; Li, Hong-Song; Chen, Chien-Hung

2008-11-30

The influence of surface acidity of activated carbon (AC) was experimentally studied on adsorption of ammonia (NH(3)). Coconut shell-based AC was modified by various acids at different concentrations. There were five different acids employed to modified AC, which included nitric acid, sulfuric acid, hydrochloric acid, phosphoric acid, and acetic acid. Acidic functional groups on the surface of ACs were determined by a Fourier transform infrared spectrograph (FTIR) and by the Boehm titration method. Specific surface area and pore volume of the ACs were measured by a nitrogen adsorption apparatus. Adsorption amounts of NH(3) onto the ACs were measured by a dynamic adsorption system at room temperature according to the principle of the ASTM standard test method. The concentration of NH(3) in the effluent stream was monitored by a gas-detecting tube technique. Experimental results showed that adsorption amounts of NH(3) on the modified ACs were all enhanced. The ammonia adsorption amounts on various activated carbons modified by different acids are in the following order: nitric acid>sulfuric acid>acetic acid approximately phosphoric acid>hydrochloric acid. It is worth to note that the breakthrough capacity of NH(3) is linearly proportional to the amount of acidic functional groups of the ACs.

Maximum power output and load matching of a phosphoric acid fuel cell-thermoelectric generator hybrid system

Science.gov (United States)

Chen, Xiaohang; Wang, Yuan; Cai, Ling; Zhou, Yinghui

2015-10-01

Based on the current models of phosphoric acid fuel cells (PAFCs) and thermoelectric generators (TGs), a new hybrid system is proposed, in which the effects of multi-irreversibilities resulting from the activation, concentration, and ohmic overpotentials in the PAFC, Joule heat and heat leak in the TG, finite-rate heat transfer between the TG and the heat reservoirs, and heat leak from the PAFC to the environment are taken into account. Expressions for the power output and efficiency of the PAFC, TG, and hybrid system are analytically derived and directly used to discuss the performance characteristics of the hybrid system. The optimal relationship between the electric currents in the PAFC and TG is obtained. The maximum power output is numerically calculated. It is found that the maximum power output density of the hybrid system will increase about 150 Wm-2, compared with that of a single PAFC. The problem how to optimally match the load resistances of two subsystems is discussed. Some significant results for practical hybrid systems are obtained.

High Extraction Phosphors for Solid State Lighting

Energy Technology Data Exchange (ETDEWEB)

Summers, Chris [Phosphortech Corporation, Kennesaw, GA (United States); Menkara, Hisham [Phosphortech Corporation, Kennesaw, GA (United States); Wagner, Brent [Phosphortech Corporation, Kennesaw, GA (United States)

2011-09-01

We have developed high-index, high efficiency bulk luminescent materials and novel nano-sized phosphors for improved solid-state white LED lamps. These advances can potentially contribute to reducing the loss in luminous efficiencies due to scattering, re-absorption, and thermal quenching. The bulk and nanostructured luminescent materials investigated are index matched to GaN and have broad and size-tunable absorption bands, size and impurity tuned emission bands, size-driven elimination of scattering effects, and a separation between absorption and emission bands. These innovations were accomplished through the use of novel synthesis techniques suitable for high volume production for LED lamp applications. The program produced a full-color set of high quantum yield phosphors with high chemical stability. In the bulk phosphor study, the ZnSeS:Cu,Ag phosphor was optimized to achieve >91% efficiency using erbium (Er) and other activators as sensitizers. Detailed analysis of temperature quenching effects on a large number of ZnSeS:Cu,Ag,X and strontium- and calcium-thiogallate phosphors lead to a breakthrough in the understanding of the anti-quenching behavior and a physical bandgap model was developed of this phenomena. In a follow up to this study, optimized phosphor blends for high efficiency and color performance were developed and demonstrated a 2-component phosphor system with good white chromaticity, color temperature, and high color rendering. By extending the protocols of quantum dot synthesis, large nanocrystals, greater than 20 nm in diameter were synthesized and exhibited bulk-like behavior and blue light absorption. The optimization of ZnSe:Mn nanophosphors achieved ~85% QE The limitations of core-shell nanocrystal systems were addressed by investigating alternative deltadoped structures. To address the manufacturability of these systems, a one-pot manufacturing protocol was developed for ZnSe:Mn nanophosphors. To enhance the stability of these material

PEM steam electrolysis at 130 °C using a phosphoric acid doped short side chain PFSA membrane

DEFF Research Database (Denmark)

Hansen, Martin Kalmar; Aili, David; Christensen, Erik

2012-01-01

Steam electrolysis test with a phosphoric acid doped Aquivion™ membrane was successfully conducted and current densities up to 775 mA cm-2 at 1.8 V was reached at 130 ºC and ambient pressure. A new composite membrane system using a perfluorosulfonic acid membrane (Aquivion™) as matrix and phospho...... implied that a new and highly corrosion resistant construction material was needed. Tantalum coated stainless steel felt was tested and found suitable as the anode gas diffusion layer. Copyright © 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved....

Recovery of uranium contained in phosphoric acid by a wet method and its transformation in a high-purity uraniferous concentrates

International Nuclear Information System (INIS)

Davister, A.; Dubreucq, A.; Granville, G.; Gray, H.

1984-01-01

There are altogether three plants in active operation today for the recovery of uranium contained in the phosphoric acid, two in the USA and one in Prayon in Belgium. All three utilize the same solvant, i.e. the Depa-Topo mixture. The Prayon plant was started up in May 1980. Phosphoric acid is desaturated before the extraction for a long time at a low temperature, totally free from mineral and organic solids and rid of its soluble humic matter until a clear acid of very low optical density is obtained. During the re-extraction of the first cycle, the reduction of U 6+ into U 4+ is effected by metallic iron, according to an original patented process which permits the reduction of the introduced iron to a strict minimum. At the end of the second cycle, an original technique permits the precipitation of a uranium and ammonium hydroxide, starting from the aqueous phase, first separated from the organic phase and purified as regards iron; because of this, the concentrate requires no roasting [fr

Limiting Current of Oxygen Reduction on Gas-Diffusion Electrodes for Phosphoric Acid Fuel Cells

DEFF Research Database (Denmark)

Li, Qingfeng; Gang, Xiao; Hjuler, Hans Aage

1994-01-01

on polytetrafluorine-ethyl bonded gas-diffusion electordes in phosphoric acid with and without fluorinated additives. This provides an alternative to estimate the film thickness by combining it with the acid-adsorption measurements and the porosity analysis of the catalyst layer. It was noticed that the limiting......Various models have been devoted to the operation mechanism of porous diffusion electrodes. They are, however, suffering from the lack of accuracy concerning the acid-film thickness on which they are based. In the present paper the limiting current density has been measured for oxygen reduction...... current density can be accomplished either by gas-phase diffusion or liquid-phase diffusion, and it is the latter that can be used in the film-thickness estimation. It is also important to mention that at such a limiting condition, both the thin-film model and the filmed agglomerate model reach the same...

Study of corrosion-erosion behaviour of stainless alloys in industrial phosphoric acid medium

Energy Technology Data Exchange (ETDEWEB)

Guenbour, Abdellah [Laboratory of Electrochemistry-Corrosion, Av. Ibn Batouta, BP1014-Faculty of Science, Rabat (Morocco)]. E-mail: guenbour@fsr.ac.ma; Hajji, Mohamed-Adil [Group Corrosion and Protection of Materials, ENIM, Rabat (Morocco); Jallouli, El Miloudi [Group Corrosion and Protection of Materials, ENIM, Rabat (Morocco); Bachir, Ali Ben [Laboratory of Electrochemistry-Corrosion, Av. Ibn Batouta, BP1014-Faculty of Science, Rabat (Morocco)

2006-12-30

The corrosion and corrosion-abrasion resistance of some stainless steels in industrial phosphoric acid 30% P{sub 2}O{sub 5} has been studied using electrochemical techniques. The corrosion rate of materials increases with the increase of temperature. Alloys which contain chromium, molybdenum and nitrogen in sufficient quantities present the best behaviour. In the abrasion-corrosion conditions, the experimental device set up allowed to follow continually samples electrochemical behaviour. Under dynamic conditions and without solid particles, the increase of acid projection speed has no effect on the alloys corrosion behaviour. The adding of abrasive leads to a general increase of corrosion rate and to a decrease of material resistance. Under these conditions, materials attack is controlled by synergistic effect between the abrasion and the impurities. The cast 30% Cr shows good resistance according to his high chromium content.

Study of corrosion-erosion behaviour of stainless alloys in industrial phosphoric acid medium

International Nuclear Information System (INIS)

Guenbour, Abdellah; Hajji, Mohamed-Adil; Jallouli, El Miloudi; Bachir, Ali Ben

2006-01-01

The corrosion and corrosion-abrasion resistance of some stainless steels in industrial phosphoric acid 30% P 2 O 5 has been studied using electrochemical techniques. The corrosion rate of materials increases with the increase of temperature. Alloys which contain chromium, molybdenum and nitrogen in sufficient quantities present the best behaviour. In the abrasion-corrosion conditions, the experimental device set up allowed to follow continually samples electrochemical behaviour. Under dynamic conditions and without solid particles, the increase of acid projection speed has no effect on the alloys corrosion behaviour. The adding of abrasive leads to a general increase of corrosion rate and to a decrease of material resistance. Under these conditions, materials attack is controlled by synergistic effect between the abrasion and the impurities. The cast 30% Cr shows good resistance according to his high chromium content

Efficacy of fungicide combinations, phosphoric acid, and plant extract from stinging nettle on potato late blight management and tuber yield

Science.gov (United States)

Late blight, caused by Phytophthora infestans is a major constraint to potato production. Inadequate management of the disease has often resulted in heavy losses in various production regions. We assessed the efficacy of fungicides, phosphoric acid, and stinging nettle plant extract combinations for...

Ocean life breaking rules by building shells in acidic extremes.

Science.gov (United States)

Doubleday, Zoë A; Nagelkerken, Ivan; Connell, Sean D

2017-10-23

Rising levels of carbon dioxide (CO 2 )from fossil fuel combustion is acidifying our oceans [1,2]. This acidification is expected to have negative effects on calcifying animals because it affects their ability to build shells [3,4]. However, the effects of ocean acidification in natural environments, subject to ecological and evolutionary processes (such as predation, competition, and adaptation), is uncertain [5,6]. These processes may buffer, or even reverse, the direct, short-term effects principally measured in laboratory experiments (for example, [6]). Here we describe the discovery of marine snails living at a shallow-water CO 2 vent in the southwest Pacific, an environment 30 times more acidic than normal seawater (Figure 1). By measuring the chemical fingerprints locked within the shell material, we show that these snails have a restricted range of movement, which suggests that they live under these conditions for their entire lives. The existence of these snails demonstrates that calcifying animals can build their shells under the acidic and corrosive conditions caused by extreme CO 2 enrichment. This unforeseen capacity, whether driven by ecological or adaptive processes, is key to understanding whether calcifying life may survive a high-CO 2 future. Copyright © 2017 Elsevier Ltd. All rights reserved.

Porous polybenzimidazole membranes doped with phosphoric acid: Preparation and application in high-temperature proton-exchange-membrane fuel cells

International Nuclear Information System (INIS)

Li, Jin; Li, Xiaojin; Yu, Shuchun; Hao, Jinkai; Lu, Wangting; Shao, Zhigang; Yi, Baolian

2014-01-01

Highlights: • Porous polybenzimidazole membrane was prepared with glucose as porogen. • Phosphoric acid content was as high as 15.7 mol H 3 PO 4 per PBI repeat unit. • 200 h Constant current density test was carried out at 150 °C. • Degradation was due to the gap between membrane and catalyst layer. - Abstract: In this paper, the preparation and characterization of porous polybenzimidazole membranes doped with phosphoric acid were reported. For the preparation of porous polybenzimidazole membranes, glucose and saccharose were selected as porogen and added into PBI resin solution before solvent casting. The prepared porous PBI membranes had high proton conductivity and high content of acid doping at room temperature with 15.7 mol H 3 PO 4 per PBI repeat unit, much higher than pure PBI membrane at the same condition. Further, the performance and stability of the porous PBI membrane in high-temperature proton-exchange-membrane fuel cells was tested. It was found that the cell performance remained stable during 200 h stability test under a constant current discharge of 0.5 A cm −2 except for the last fifty hours. The decay in the last fifty hours was ascribed to the delamination between the catalyst layer and membrane increasing the charge-transfer resistance

Influence of gamma irradiation on microbiological and chemical characteristics of shelled and unshelled stored pecan (carya illinoinsis)

International Nuclear Information System (INIS)

Abd El Wahab, S.A.E.; El Salhy, F.T.A.; Mahmoud, A.M.

2010-01-01

Shelled and unshelled pecan nuts were treated with 0,1.53 and 5 kGy of gamma irradiation . The irradiated and non-irradiated nuts were stored in polyethylene bags for 0,2,4,6, and 8 months at room temperature. Total bacterial count and total mold and yeast, proximate composition (moisture, protein, fat and ash content), total free amino acids, total fatty acids, reducing and non-reducing sugars, phosphorous and potassium of nuts were evaluated immediately after irradiation and after each storage period . The results indicated that gamma irradiation reduced total bacterial count and total fungal load of pecan. Irradiation doses did not cause any significant changes in proximate composition of pecan.

COMPARATIVE STUDY OF THE SHEAR BOND STRENGTH OF COMPOSITE RESIN TO DENTAL ENAMEL CONDITIONED WITH PHOSPHORIC ACID OR Nd: YAG LASER

Directory of Open Access Journals (Sweden)

EDUARDO Carlos de Paula

1997-01-01

Full Text Available This study has been focused on a comparison between the shear bond strength of a composite resin attached to dental enamel surface, after a 35% phosphoric acid etching and after a Nd:YAG laser irradiation with 165.8 J/cm2 of energy density per pulse. After etching and attaching resin to these surfaces, the specimens were thermocycled and then underwent the shearing bond strength tests at a speed of 5 mm/min. The results achieved, after statistical analysis with Student's t-test, showed that the adhesion was significantly greater in the 35% phosphoric acid treated group than in the group treated with the Nd:YAG laser, thus demonstrating the need for developing new studies to reach the ideal parameters for an effective enamel surface conditioning as well as specific adhesives and composite resins when Nd:YAG laser is used

Isotope-labelled folic acid derivatives

International Nuclear Information System (INIS)

Lewin, N.; Wong, E.T.

1976-01-01

The suggestion deals with the production of folic acid derivatives suitable as indicators or tracers for analyses of serum folates. These folic acid derivatives contain folic acid which is bound by one or both carboxyl groups to the amino nitrogen of compounds such as, e.g., tyramine, glycyl tyrosine, tyrosine, or the methyl ester of tyrosine. The derivative obtained can be substituted by a gamma emitter, e.g. the iodine isotope I 125. The radioactive derivative is used in the method for the competitive protein bonding to determine endogenic folates in the serum. (UWI) [de

Role of keto–enol tautomerization in a chiral phosphoric acid catalyzed asymmetric thiocarboxylysis of meso-epoxide: a DFT study

KAUST Repository

Ajitha, Manjaly John; Huang, Kuo-Wei

2015-01-01

The mechanism of a chiral phosphoric acid catalyzed thiocarboxylysis of meso-epoxide was investigated by density functional theory (DFT) calculations (M06-2X). The nucleophilic ring opening of epoxide by thiobenzoic acid was found to proceed via a concerted termolecular transition state with a simultaneous dual proton transfer to yield the β-hydroxy thioester product. Electrostatic interactions together with the steric environment inside the chiral catalyst play an important role in determining the enantioselectivity of the reaction.

Role of keto–enol tautomerization in a chiral phosphoric acid catalyzed asymmetric thiocarboxylysis of meso-epoxide: a DFT study

KAUST Repository

Ajitha, Manjaly John

2015-09-15

The mechanism of a chiral phosphoric acid catalyzed thiocarboxylysis of meso-epoxide was investigated by density functional theory (DFT) calculations (M06-2X). The nucleophilic ring opening of epoxide by thiobenzoic acid was found to proceed via a concerted termolecular transition state with a simultaneous dual proton transfer to yield the β-hydroxy thioester product. Electrostatic interactions together with the steric environment inside the chiral catalyst play an important role in determining the enantioselectivity of the reaction.

Systematic investigation of the synthesis of core-shell poly(styrene-co-acrylic acid) colloids with varying shell thickness and core diameter

DEFF Research Database (Denmark)

Hinge, Mogens; Keiding, Kristian

2006-01-01

the morphology of the material for an specific application is going on. It is known from SFEP of styrene that the final colloidal size can be controlled by adjusting the ionic strength of the synthesis feed [1] and it is suggested that adding acrylic acid to the synthesis will result in a change...... in polymerization locus from the core to the surface [2]. There is at present not performed a systematically investigation in controlling the core size and shell thickness of poly(styrene-co-acrylic acid) core-shell colloids  (poly(ST-co-AA)).   Poly(ST-co-AA) colloids were synthesized by free-radical surfactant......-free emulsion co-polymerization (SFECP) at 70°C, using styrene as monomer and acrylic acid as co-monomer. Different batches of poly(ST-co-AA) colloids were synthesized with varying ionic strength and acrylic acid concentrations in the synthesis feed. The produced poly(ST-co-AA) colloids were analysed...

Determination of uranium in urine samples for workers in the phosphoric acid purification using fluorimetry technique

International Nuclear Information System (INIS)

Kharita, M. H.; Sakhita, Kh.; Aldalal, Z.

2003-10-01

There is probability of exposure to uranium for workers in the phosphoric acid purification (internal exposure) by inhalation, and the deposition of this uranium in organs and tissues, and the consequence excreation out of the body by perspiration or urine. This study focuses on the determination of uranium in urine samples of workers. All results seem to be under the detection limit of the method, therefore no routine monitoring is required. (author)

White LED based on CaAl2Si2O8:Eu2+ Mn2+ phosphor and CdS/ZnS quantum dots

Science.gov (United States)

Shen, Changyu; Zhong, Chuan; Hou, Qianglong; Li, Ke

2011-02-01

Core/shell CdS/ZnS quantum dots (QDs) with the emission wavelength of 610nm, was synthesized by thermal deposition using cadmium oxide and selenium as precursors in a hot lauric acid and hexadecylamine trioctylphosphine oxide hybrid. CaAl2Si2O8:Eu2+ Mn2+ phosphor was synthesized by high-temperature solid state reaction at 1290 °C for 2 hours under the H2 reducing atmosphere, and X-ray powder diffraction analysis confirmed the formation of it. It has two emission bands peaking at 420 nm and 580nm originated from the transition 5d to 4f of Eu2+ and 4T1-6A1 of Mn2+, respectively. Blends of CaAl2Si2O8:Eu2+,Mn2+ phosphor and CdS/ZnS QDs exhibited the prominent spectral evolution with an increasing content of QDs. A hybrid white LED, which combines a blue LED with the blend of CaAl2Si2O8:Eu2+ Mn2+ phosphor and QDs with a weight ratio of 2:1, with the CIE coordinate of (0.3183, 0.3036) and CRI of 85 was obtained.

(Di­methyl­phosphor­yl)methanaminium hydrogen oxalate–oxalic acid (2/1)

Science.gov (United States)

Bialek, Sebastian; Clemens, Rebecca; Reiss, Guido J.

2014-01-01

The reaction of (di­methyl­phosphor­yl)methanamine (dpma) with oxalic acid in ethanol yielded the title solvated salt, C3H11NOP+·C2HO4 −·0.5C2H2O4. Its asymmetric unit consists of one dpmaH+ cation, one hydrogen oxalate anion and a half-mol­ecule of oxalic acid located around a twofold rotation axis. The H atom of the hydrogen oxalate anion is statistically disordered over two positions that are trans to each other. The hydrogen oxalate monoanion is not planar (bend angle ∼16°) whereas the oxalic acid molecule shows a significantly smaller bend angle (∼7°). In the crystal, the components are connected by strong O—H⋯O and much weaker N—H⋯O hydrogen bonds, leading to the formation of layers extending parallel to (001). The structure was refined from a racemically twinned crystal with twin components in an approximate 1:1 ratio. PMID:24765013

Physico-chemical characterization studies of activated carbon derived from Sterculia Quadrifida seed shell waste

Directory of Open Access Journals (Sweden)

P. Shanthi

2014-09-01

Full Text Available A carbonaceous adsorbent prepared from the Sterculia Quadrifida shell by various activation process, viz., Acid process, Chloride process, Carbonate process and Sulphate process are successfully reported. It shows excellent improvement in the surface characteristics. Their physico-chemical characterization studies such as bulk density, moisture content, ash content, fixed carbon content, matter, soluble in water, matter soluble in acid, pH, decolourizing power, porosity and specific gravity have been carried out to assess the suitability of these carbons as potential adsorbent for waste water treatment. The present study undertaken to evaluate the efficiency of a carbon adsorbent prepared from Sterculia Quadrifida seed shell waste for removal of dyes in aqueous solution.

A new planetary structure fabrication process using phosphoric acid

Science.gov (United States)

Buchner, Christoph; Pawelke, Roland H.; Schlauf, Thomas; Reissner, Alexander; Makaya, Advenit

2018-02-01

Minimising the launch mass is an important aspect of exploration mission planning. In-situ resource utilisation (ISRU) can improve this by reducing the amount of terrestrial materials needed for planetary exploration activities. We report on a recently concluded investigation into the requirements and available technologies for creating hardware on extra-terrestrial bodies, using the limited resources available on site. A trade-off of ISRU technologies for hardware manufacturing was conducted. A new additive manufacturing process suitable for fabricating structures on the Moon or Mars was developed. The process uses planetary regolith as the base material and concentrated phosphoric acid as the liquid binder. Mixing the reagents creates a sticky construction paste that slowly solidifies into a hard, rock-like material. Prior to solidification, the paste is extruded in layers, creating the desired structures in a 3D printing process. We used Martian regolith simulant JSC-Mars-1A, but the process is not selective towards regolith composition. Samples were exposed to thermal cycles and were mechanically characterised. Reduced-scale demonstrator structures were printed to demonstrate structure fabrication using the developed process.

Pyroelectric properties of phosphoric acid-doped TGS single crystals

International Nuclear Information System (INIS)

Saxena, Aparna; Fahim, M; Gupta, Vinay; Sreenivas, K

2003-01-01

Pyroelectric properties of phosphoric acid (H 3 PO 4 )-doped triglycine sulfate (TGSP) single crystals grown from solutions containing 0.1-0.5 mol of H 3 PO 4 have been studied. Incorporation of H 3 PO 4 into the crystal lattice is found to induce an internal bias field (E b ) and is observed through the presence of a sustained polarization and pyroelectricity beyond the transition temperature. The internal bias field has been estimated theoretically by fitting the experimentally measured data on temperature dependence of the pyroelectric coefficient (λ), dielectric constant (ε') and polarization (P). A high E b value in the range 9 x 10 3 -15.5 x 10 4 V m -1 is obtained for crystals grown with 0.1-0.5 mol of H 3 PO 4 in the solution, and a specific concentration of 0.2-0.25 mol of H 3 PO 4 in the solution during crystal growth is found to be optimum for a high figure of merit for detectivity, F d = 428 μC m -2 K -1

Formation of rod type structures of CaSO4: Ce,P,Dy TLD phosphor using different synthesis routes

International Nuclear Information System (INIS)

Atone, M.S.; Wani, J.A.; Dhoble, S.J.

2011-01-01

Effect of Ce and P co-activation in CaSO 4 : Dy, standard TLD phosphor prepared by different synthesis root techniques and it's structural morphology is reported first time in this paper. We have already reported the sensitization of luminescence in CaSO 4 : Dy with phosphorous (P) and cerium (Ce) ions separately via acid distillation route. In the current investigation, we have doped these impurities (Ce, P, Dy) simultaneously in CaSO 4 host lattice. We have employed a well known chemical precipitation method and modified acid distillation method and have attempted to analyse the surface morphology resulted from these two synthesis routes. Chemical precipitation usually takes place at room temperature and in this way allows the reaction to take place silently. In case of acid distillation method we have reduced the synthesis temperature to 493K which is considerably less than 653K employed in previously reported literature. In case of precipitation method particle shape seems to be spherical and particle size is around one micro range or in the neighbourhood of nanorange. However, in the case of modified acid distillation method particles have shaped in to rod like structures and particle size again falls in the micro range. The photoluminescence intensity of the phosphor prepared by chemical precipitation method is weak as compared to the phosphor prepared by modified acid distillation method. Both the phosphors prepared by different methods have shown characteristic transitions of dopants. The emission spectra of prepared phosphors at 309 nm and 329 nm of Ce 3+ ions overlap well with excitation of Dy 3+ ions. Thermoluminescence (TL) property of both phosphors is again good though certain variation is observed in case of phosphor prepared by modified acid distillation method which shows rod like structure of phosphor. This variation in TL may be attributed to change in surface morphology (formation of rod type structure of particles) of the phosphor. (author)

Angle-resolved photoluminescence spectrum of a uniform phosphor layer

Science.gov (United States)

Fujieda, Ichiro; Ohta, Masamichi

2017-10-01

A photoluminescence spectrum depends on an emission angle due to self-absorption in a phosphor material. Assuming isotropic initial emission and Lambert-Beer's law, we have derived simple expressions for the angle-resolved spectra emerging from the top and bottom surfaces of a uniform phosphor layer. The transmittance of an excitation light through the phosphor layer can be regarded as a design parameter. For a strongly-absorbing phosphor layer, the forward flux is less intense and more red-shifted than the backward flux. The red-shift is enhanced as the emission direction deviates away from the plane normal. When we increase the transmittance, the backward flux decreases monotonically. The forward flux peaks at a certain transmittance value. The two fluxes become similar to each other for a weakly-absorbing phosphor layer. We have observed these behaviors in experiment. In a practical application, self-absorption decreases the efficiency of conversion and results in angle-dependent variations in chromaticity coordinates. A patterned phosphor layer with a secondary optical element such as a remote reflector alleviates these problems.

A Novel Method for Fabricating Double Layers Porous Anodic Alumina in Phosphoric/Oxalic Acid Solution and Oxalic Acid Solution

Directory of Open Access Journals (Sweden)

Yanfang Xu

2016-01-01

Full Text Available A novel method for fabricating ordered double layers porous anodic alumina (DL-PAA with controllable nanopore size was presented. Highly ordered large pore layer with interpore distance of 480 nm was fabricated in phosphoric acid solution with oxalic acid addition at the potential of 195 V and the small pore layer was fabricated in oxalic acid solution at the potential from 60 to 100 V. Experimental results show that the thickness of large pore layer is linearly correlative with anodizing time, and pore diameter is linearly correlative with pore widening time. When the anodizing potential in oxalic acid solution was adjusted from 60 to 100 V, the small pore layers with continuously tunable interpore distance from 142 to 241 nm and pore density from 1.94×109 to 4.89×109 cm−2 were obtained. And the interpore distance and the pore density of small pore layers are closely correlative with the anodizing potential. The fabricated DL-PAA templates can be widely utilized for fabrication of ordered nanomaterials, such as superhydrophobic or gecko-inspired adhesive materials and metal or semiconductor nanowires.

Organocatalytic asymmetric selenofunctionalization of tryptamine for the synthesis of hexahydropyrrolo[2,3-b]indole derivatives

Directory of Open Access Journals (Sweden)

Qiang Wei

2013-08-01

Full Text Available A chiral phosphoric acid-catalyzed selenofunctionalization of tryptamine derivatives provides access to 3a-(phenylselenyl-1,2,3,3a,8,8a-hexahydropyrrolo[2,3-b]indole derivatives in high yields and with synthetically useful levels of enantioselectivity (up to 89% ee.

Study of the interference of uranium, vanadium, aluminium and molebdenum in the determination of FeII, FeIII in Syrian phosphoric acid by spectrophotometry

International Nuclear Information System (INIS)

Zaizafoun, Ghadir; Elian, Nazha

1991-04-01

The spectrophotometric determination of the ratio of iron I I to iron I II in crude phosphoric acid is of great importance because of its influence on the redox potential in the different stages which lead to the extraction of uranium from crude phosphoric acid. The suitability of a number of reagents for this determination was examined and only 1,10-phenanthroline, 5-sulfosalicylic acid and 2,2'-bipyridine were selected for further experimentation. 1-10-phenanthroline can give a deep red complex with Fe I I, in phosphoric acid medium at PH 4-6, absorbs at λ = 510 nm. The total iron was determined by reducing Fe I II to Fe I I using hydroxylamine hydrochloride. The second reagent was found capable of forming a yellow complex absorbs light at λ = 430 nm in amonia medium at PH 8.5 - 11 with Fe I II. The adopted procedure was to determine total iron first by oxidation with nitric acid. Then iron I I was determined in a second test at PH 1.5 and at λ = 500 nm. The third reagent i.e. 2-2' bipyridine is capable of forming a red complex with iron I I absorbs at λ = 522 nm. The interference of U, V, Al, and Mo was investigated. These elements were selected because of their presence in considerable amounts in Syrian commercial phosphoric acid. The work was designed so that the effect of the presence of each element as well as the presence of all possible combinations of these elements can be estimated. The investigation revealed that the interference is very high in the case of 2-2' bipyridine in addition to the instability of the complex. In the case of 1,10-phenanthroline the interference was also found high. Thus these two reagents were disregarded. The 5-sulfosalicylic reagent was found satisfactory when determining iron I II, However when Fe I I is considered the error resulting from interference ranges between 17.5 - 50%. This error was found very dependent on the PH of the medium and further work is in progress in order to lower the value of interferences

Hydrogen evolution activity and electrochemical stability of selected transition metal carbides in concentrated phosphoric acid

DEFF Research Database (Denmark)

Tomás García, Antonio Luis; Jensen, Jens Oluf; Bjerrum, Niels J.

2014-01-01

phosphoric acid were investigated in a temperature range from 80 to 170°C. A significant dependence of the activities on temperature was observed for all five carbide samples. Through the entire temperature range Group 6 metal carbides showed higher activity than that of the Group 5 metal carbides......Alternative catalysts based on carbides of Group 5 (niobium and tantalum) and 6 (chromium, molybdenum and tungsten) metals were prepared as films on the metallic substrates. The electrochemical activities of these carbide electrodes towards the hydrogen evolution reaction (HER) in concentrated...

Local functional derivative of the total energy and the shell structure in atoms and molecules

NARCIS (Netherlands)

Pino, R.; Markvoort, Albert. J.; Santen, van R.A.; Hilbers, P.A.J.

2003-01-01

The full and local Thomas–Fermi–Dirac energy functional derivatives are evaluated at Hartree–Fock densities for several atoms and molecules. These functions are interpreted as local chemical potentials and related mainly to kinetic energy functional derivatives. They are able to reveal the shell

Importance-truncated shell model for multi-shell valence spaces

Energy Technology Data Exchange (ETDEWEB)

Stumpf, Christina; Vobig, Klaus; Roth, Robert [Institut fuer Kernphysik, TU Darmstadt (Germany)

2016-07-01

The valence-space shell model is one of the work horses in nuclear structure theory. In traditional applications, shell-model calculations are carried out using effective interactions constructed in a phenomenological framework for rather small valence spaces, typically spanned by one major shell. We improve on this traditional approach addressing two main aspects. First, we use new effective interactions derived in an ab initio approach and, thus, establish a connection to the underlying nuclear interaction providing access to single- and multi-shell valence spaces. Second, we extend the shell model to larger valence spaces by applying an importance-truncation scheme based on a perturbative importance measure. In this way, we reduce the model space to the relevant basis states for the description of a few target eigenstates and solve the eigenvalue problem in this physics-driven truncated model space. In particular multi-shell valence spaces are not tractable otherwise. We combine the importance-truncated shell model with refined extrapolation schemes to approximately recover the exact result. We present first results obtained in the importance-truncated shell model with the newly derived ab initio effective interactions for multi-shell valence spaces, e.g., the sdpf shell.

3,3'-Diaryl-BINOL phosphoric acids as enantioselective extractants of benzylic primary amines.

Science.gov (United States)

Verkuijl, Bastiaan J V; de Vries, Johannes G; Feringa, Ben L

2011-01-01

We report that 3,3'-diaryl-BINOL phosphoric acids are effective enantioselective extractants in chiral separation methods based on reactive liquid-liquid extraction. These new extractants are capable of separating racemic benzylic primary amine substrates. The effect of the nature of the substituents at the 3,3'-positions of the host were examined as well as the structure of the substrate, together with important parameters such as the organic solvent, the pH of the aqueous phase, and the host stoichiometry. Titration of the substrate with the host was monitored by FTIR, NMR, UV-Vis, and CD spectroscopy, which provided insight into the structure of the host-guest complex involved in extraction. Copyright © 2010 Wiley-Liss, Inc.

Comparison of different phosphorous adsorption models in acid ...

African Journals Online (AJOL)

This study was designed to compare the phosphorous fixation capacity of three soils series named Tyele, Minkonmingon and Mekoto in the south region of Cameroon and to determine the soil properties that are the main predictors of the P activity of those soils. Five adsorption equations viz. Linear, Langmuir, Van Huay, ...

Drug Nanoparticle Formulation Using Ascorbic Acid Derivatives

Directory of Open Access Journals (Sweden)

Kunikazu Moribe

2011-01-01

Full Text Available Drug nanoparticle formulation using ascorbic acid derivatives and its therapeutic uses have recently been introduced. Hydrophilic ascorbic acid derivatives such as ascorbyl glycoside have been used not only as antioxidants but also as food and pharmaceutical excipients. In addition to drug solubilization, drug nanoparticle formation was observed using ascorbyl glycoside. Hydrophobic ascorbic acid derivatives such as ascorbyl mono- and di-n-alkyl fatty acid derivatives are used either as drugs or carrier components. Ascorbyl n-alkyl fatty acid derivatives have been formulated as antioxidants or anticancer drugs for nanoparticle formulations such as micelles, microemulsions, and liposomes. ASC-P vesicles called aspasomes are submicron-sized particles that can encapsulate hydrophilic drugs. Several transdermal and injectable formulations of ascorbyl n-alkyl fatty acid derivatives were used, including ascorbyl palmitate.

Boronic Acid functionalized core-shell polymer nanoparticles prepared by distillation precipitation polymerization for glycopeptide enrichment.

Science.gov (United States)

Qu, Yanyan; Liu, Jianxi; Yang, Kaiguang; Liang, Zhen; Zhang, Lihua; Zhang, Yukui

2012-07-16

The boronic acid-functionalized core-shell polymer nanoparticles, poly(N,N-methylenebisacrylamide-co-methacrylic acid)@4-vinylphenylboronic acid (poly(MBA-co-MAA)@VPBA), were successfully synthesized for enriching glycosylated peptides. Such nanoparticles were composed of a hydrophilic polymer core prepared by distillation precipitation polymerization (DPP) and a boronic acid-functionalized shell designed for capturing glycopeptides. Owing to the relatively large amount of residual vinyl groups introduced by DPP on the core surface, the VPBA monomer was coated with high efficiency, working as the shell. Moreover, the overall polymerization route, especially the use of DPP, made the synthesis of nanoparticles facile and time-saving. With the poly(MBA-co-MAA)@VPBA nanoparticles, 18 glycopeptides from horseradish peroxidase (HRP) digest were captured and identified by MALDI-TOF mass spectrometric analysis, relative to eight glycopeptides enriched by using commercially available meta-aminophenylboronic acid agarose under the same conditions. When the concentration of the HRP digest was decreased to as low as 5 nmol, glycopeptides could still be selectively isolated by the prepared nanoparticles. Our results demonstrated that the synthetic poly(MBA-co-MAA)@VPBA nanoparticles might be a promising selective enrichment material for glycoproteome analysis. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

External radiation assessment in a wet phosphoric acid production plant

Energy Technology Data Exchange (ETDEWEB)

Bolivar, J.P.; Perez-Moreno, J.P. [Dept. Fisica Aplicada, Facultad de Ciencias Experimentales, Universidad de Huelva, 21012 Huelva (Spain); Mas, J.L. [Dept. Fisica Aplicada I, Escuela Universitaria Politecnica, Universidad de Sevilla, 41012 Sevilla (Spain)], E-mail: ppmasb@us.es; Martin, J.E.; San Miguel, E.G. [Dept. Fisica Aplicada, Facultad de Ciencias Experimentales, Universidad de Huelva, 21012 Huelva (Spain); Garcia-Tenorio, R. [Dept. Fisica Aplicada II, Escuela Tecnica Superior de Arquitectura, Universidad de Sevilla, 41012 Sevilla (Spain)

2009-10-15

The factories dedicated to the production of phosphoric acid by the so-called wet acid method are usually considered typical NORM industries, because the phosphate rock used as raw material usually contains high concentrations of {sup 238}U-series radionuclides. The magnitude and behaviour of the radionuclides involved in the production process revealed the need to determine its dosimetric impact on workers. This work aims to partially compensate this lack of knowledge through the determination of external effective dose rates at different zones in the process at a typical plant located in the southwest of Spain. To this end, two dosimetric sampling campaigns have been carried out at this phosphoric acid production plant. The first sampling was carried out when phosphate rocks originating in Morocco were processed, and the second one when phosphate rock processed came from the Kola Peninsula (Russia Federation). This differentiation was necessary because the activity concentrations are almost one order of magnitude higher in Moroccan phosphate rock than in Kola phosphate rock. The results obtained have reflected external dose rate enhancements as high as 1.4 {mu}Sv h{sup -1} (i.e., up to thirty times the external exposition due to radionuclides in unperturbed soils) at several points in the facility, particularly where the digested rock (pulp) is filtered. However, the most problematic points are characterised by a small occupation factor. That means that the increment in the annual effective external gamma dose received by the most-exposed worker is clearly below 1 mSv (European Commission limit for the general population) under normal production. Nevertheless, special care in the design and schedule of cleaning and maintaining work in the areas with high doses should be taken in order to avoid any possibility of exceeding the previously mentioned general population limit. In addition, the results of the dosimetric campaign showed no clear correlation between {sup

Phosphors

International Nuclear Information System (INIS)

1975-01-01

This invention relates to phosphors that can be used in fluorescent lamps and display devices. The phosphor is comprised of a halophosphate of calcium and/or strontium of apatite crystal structure activated with trivalent cerium and trivalent terbium. The phosphor can further include manganese. Preferably, the phosphor includes up to 10% by weight of one or more of the alkali metals lithium, sodium and potassium in the form of a compound or compounds thereof. The emissions appear as a number of fairly narrow discrete bands. The temperature of preparation is 1000degC (as opposed to the usual 1450degC), therefore reducing costs (less energy is needed, more crucibles are readily obtainable and there is no need for special conditions to enable crucibles to overcome thermal shock)

21 CFR 172.862 - Oleic acid derived from tall oil fatty acids.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Oleic acid derived from tall oil fatty acids. 172... FOOD FOR HUMAN CONSUMPTION Multipurpose Additives § 172.862 Oleic acid derived from tall oil fatty acids. The food additive oleic acid derived from tall oil fatty acids may be safely used in food and as...

Linked-cluster perturbation theory for closed and open-shell systems: derivation of effective π-electron hamiltonians

International Nuclear Information System (INIS)

Brandow, B.H.

1977-01-01

The Brueckner--Goldstone form of linked-cluster perturbation theory is derived, together with its open-shell analog, by an elementary time-independent approach. This serves to focus attention on the physical interpretation of the results. The open-shell expansion is used to provide a straightforward justification for the effective π-electron Hamiltonians of planar organic molecules

Multifunctional Cinnamic Acid Derivatives

Directory of Open Access Journals (Sweden)

Aikaterini Peperidou

2017-07-01

Full Text Available Our research to discover potential new multitarget agents led to the synthesis of 10 novel derivatives of cinnamic acids and propranolol, atenolol, 1-adamantanol, naphth-1-ol, and (benzylamino ethan-1-ol. The synthesized molecules were evaluated as trypsin, lipoxygenase and lipid peroxidation inhibitors and for their cytotoxicity. Compound 2b derived from phenoxyphenyl cinnamic acid and propranolol showed the highest lipoxygenase (LOX inhibition (IC50 = 6 μΜ and antiproteolytic activity (IC50 = 0.425 μΜ. The conjugate 1a of simple cinnamic acid with propranolol showed the higher antiproteolytic activity (IC50 = 0.315 μΜ and good LOX inhibitory activity (IC50 = 66 μΜ. Compounds 3a and 3b, derived from methoxylated caffeic acid present a promising combination of in vitro inhibitory and antioxidative activities. The S isomer of 2b also presented an interesting multitarget biological profile in vitro. Molecular docking studies point to the fact that the theoretical results for LOX-inhibitor binding are identical to those from preliminary in vitro study.

Isolation of living Algae growing in the shells of Molluscs and Barnacles with EDTA (ethylenediaminetetraacetic acid)

NARCIS (Netherlands)

Prud’homme van Reine, W.F.; Hoek, van den C.

1966-01-01

Several decalcifying mixtures or aqueous solutions of inorganic or organic acids are generally used for releasing algae growing in the shells of molluscs and barnacles, for instance dilute hydrochloric, nitric, citric, or acetic acid (4), a mixture of nitric acid, chromic acid and alcolhol (1),

Synthesis of the mono- and di(4-(1,1,3,3-tetramethylbutyl)) phosphoric acids

International Nuclear Information System (INIS)

Elias, H.; Zaoui, A.; Attou, M.; Hadj Bachir, D.; Bouzidi, N.; Didi, M.

1995-09-01

This work is related to the synthesis of organophosphorus extracting agents used in purification of heavy metals such as uranium. The mono- and di (4-(1,1,3,3- tetramethylbutyl)) phenyl phosphoric acids, respectively MOPPA and DOPPA, are synthesizd by reaction of phosphorus pentoxid with 4(1,1,3,3-tetramethylbuthyl)) phenol. the separation of MOPPA from DOPPA is realised by liquid-liquid extraction. The Characterization, carried out by infrared uv-visible spectrophotometries, ph-metry and mass spectrometry, has confirmed the identity of the synthesized products. This study also showed that the products proportions are comporable to those of the homologous products obtained with 2-ethylbexanol in the same synthesis conditions

Pyroelectric properties of phosphoric acid-doped TGS single crystals

Energy Technology Data Exchange (ETDEWEB)

Saxena, Aparna; Fahim, M; Gupta, Vinay; Sreenivas, K [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

2003-12-21

Pyroelectric properties of phosphoric acid (H{sub 3}PO{sub 4})-doped triglycine sulfate (TGSP) single crystals grown from solutions containing 0.1-0.5 mol of H{sub 3}PO{sub 4} have been studied. Incorporation of H{sub 3}PO{sub 4} into the crystal lattice is found to induce an internal bias field (E{sub b}) and is observed through the presence of a sustained polarization and pyroelectricity beyond the transition temperature. The internal bias field has been estimated theoretically by fitting the experimentally measured data on temperature dependence of the pyroelectric coefficient ({lambda}), dielectric constant ({epsilon}') and polarization (P). A high E{sub b} value in the range 9 x 10{sup 3}-15.5 x 10{sup 4} V m{sup -1} is obtained for crystals grown with 0.1-0.5 mol of H{sub 3}PO{sub 4} in the solution, and a specific concentration of 0.2-0.25 mol of H{sub 3}PO{sub 4} in the solution during crystal growth is found to be optimum for a high figure of merit for detectivity, F{sub d} = 428 {mu}C m{sup -2} K{sup -1}.

Biodiesel Production from Castor Oil by Using Calcium Oxide Derived from Mud Clam Shell

Directory of Open Access Journals (Sweden)

S. Ismail

2016-01-01

Full Text Available The catalytic potential of calcium oxide synthesized from mud clam shell as a heterogeneous catalyst for biodiesel production was studied. The mud clam shell calcium oxide was characterized using particle size analyzer, Fourier transform infrared spectroscopy, scanning electron microscopy, and BET gas sorption analyzer. The catalyst performance of mud clam shell calcium oxide was studied in the transesterification of castor oil as biodiesel. Catalyst characterization and transesterification study results of synthesized catalyst proved the efficiency of the natural derived catalyst for biodiesel production. A highest biodiesel yield of 96.7% was obtained at optimal parameters such as 1 : 14 oil-to-methanol molar ratio, 3% w/w catalyst concentration, 60°C reaction temperature, and 2-hour reaction time. Catalyst reusability test shows that the synthesized calcium oxide from mud clam shell is reusable up to 5 times.

Inorganic polymers from laterite using activation with phosphoric acid and alkaline sodium silicate solution: Mechanical and microstructural properties

Energy Technology Data Exchange (ETDEWEB)

Lassinantti Gualtieri, Magdalena, E-mail: magdalena.gualtieri@unimore.it [Dipartimento di Ingegneria " Enzo Ferrari" , Università degli studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41125 Modena (Italy); Romagnoli, Marcello [Dipartimento di Ingegneria " Enzo Ferrari" , Università degli studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41125 Modena (Italy); Pollastri, Simone; Gualtieri, Alessandro F. [Dipartimento di Scienze Chimiche e Geologiche, Università degli studi di Modena e Reggio Emilia, Via S. Eufemia 19I, I-41121 Modena (Italy)

2015-01-15

Geopolymers from laterite, an iron-rich soil available in developing countries, have great potential as building materials. In this work, laterite from Togo (Africa) was used to prepare geopolymers using both phosphoric acid and alkaline sodium silicate solution. Microstructural properties were investigated by scanning electron microscopy, X-ray powder diffraction and mercury porosimetry, whereas thermal properties were evaluated by thermal analyses. The local environment of iron was studied by X-ray Absorption Spectroscopy (XANES region). The mechanical properties were determined. Modulus of Rupture and Young's modulus fell in the ranges 3.3–4.5 MPa and 12–33 GPa, respectively, rendering the materials good candidates for construction purposes. Heating above 900 °C results in weight-gain, presumably due to iron redox reactions. X-ray Absorption Spectroscopy data evidence changes in the chemical and structural environments of iron following thermal treatment of geopolymers. These changes indicate interaction between the geopolymer structure and iron during heating, possibly leading to redox properties. -- Highlights: •Geopolymerization of laterite is promising for fabrication of building materials. •Both phosphoric acid and alkaline sodium silicate solution can be used for activation. •Thermally activated redox properties of the inorganic polymers were observed.

Inorganic polymers from laterite using activation with phosphoric acid and alkaline sodium silicate solution: Mechanical and microstructural properties

International Nuclear Information System (INIS)

Enzo Ferrari, Università degli studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41125 Modena (Italy))" data-affiliation=" (Dipartimento di Ingegneria Enzo Ferrari, Università degli studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41125 Modena (Italy))" >Lassinantti Gualtieri, Magdalena; Enzo Ferrari, Università degli studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41125 Modena (Italy))" data-affiliation=" (Dipartimento di Ingegneria Enzo Ferrari, Università degli studi di Modena e Reggio Emilia, Via Vignolese 905/a, I-41125 Modena (Italy))" >Romagnoli, Marcello; Pollastri, Simone; Gualtieri, Alessandro F.

2015-01-01

Geopolymers from laterite, an iron-rich soil available in developing countries, have great potential as building materials. In this work, laterite from Togo (Africa) was used to prepare geopolymers using both phosphoric acid and alkaline sodium silicate solution. Microstructural properties were investigated by scanning electron microscopy, X-ray powder diffraction and mercury porosimetry, whereas thermal properties were evaluated by thermal analyses. The local environment of iron was studied by X-ray Absorption Spectroscopy (XANES region). The mechanical properties were determined. Modulus of Rupture and Young's modulus fell in the ranges 3.3–4.5 MPa and 12–33 GPa, respectively, rendering the materials good candidates for construction purposes. Heating above 900 °C results in weight-gain, presumably due to iron redox reactions. X-ray Absorption Spectroscopy data evidence changes in the chemical and structural environments of iron following thermal treatment of geopolymers. These changes indicate interaction between the geopolymer structure and iron during heating, possibly leading to redox properties. -- Highlights: •Geopolymerization of laterite is promising for fabrication of building materials. •Both phosphoric acid and alkaline sodium silicate solution can be used for activation. •Thermally activated redox properties of the inorganic polymers were observed

Fundamentals of phosphors

CERN Document Server

Yen, William M; Yamamoto, Hajime

2006-01-01

Drawing from the second edition of the best-selling Handbook of Phosphors, Fundamentals of Phosphors covers the principles and mechanisms of luminescence in detail and surveys the primary phosphor materials as well as their optical properties. The book addresses cutting-edge developments in phosphor science and technology including oxynitride phosphors and the impact of lanthanide level location on phosphor performance.Beginning with an explanation of the physics underlying luminescence mechanisms in solids, the book goes on to interpret various luminescence phenomena in inorganic and organic materials. This includes the interpretation of the luminescence of recently developed low-dimensional systems, such as quantum wells and dots. The book also discusses the excitation mechanisms by cathode-ray and ionizing radiation and by electric fields to produce electroluminescence. The book classifies phosphor materials according to the type of luminescence centers employed or the class of host materials used and inte...

Deriving the nuclear shell model from first principles

Science.gov (United States)

Barrett, Bruce R.; Dikmen, Erdal; Vary, James P.; Maris, Pieter; Shirokov, Andrey M.; Lisetskiy, Alexander F.

2014-09-01

The results of an 18-nucleon No Core Shell Model calculation, performed in a large basis space using a bare, soft NN interaction, can be projected into the 0 ℏω space, i.e., the sd -shell. Because the 16 nucleons in the 16O core are frozen in the 0 ℏω space, all the correlations of the 18-nucleon system are captured by the two valence, sd -shell nucleons. By the projection, we obtain microscopically the sd -shell 2-body effective interactions, the core energy and the sd -shell s.p. energies. Thus, the input for standard shell-model calculations can be determined microscopically by this approach. If the same procedure is then applied to 19-nucleon systems, the sd -shell 3-body effective interactions can also be obtained, indicating the importance of these 3-body effective interactions relative to the 2-body effective interactions. Applications to A = 19 and heavier nuclei with different intrinsic NN interactions will be presented and discussed. The results of an 18-nucleon No Core Shell Model calculation, performed in a large basis space using a bare, soft NN interaction, can be projected into the 0 ℏω space, i.e., the sd -shell. Because the 16 nucleons in the 16O core are frozen in the 0 ℏω space, all the correlations of the 18-nucleon system are captured by the two valence, sd -shell nucleons. By the projection, we obtain microscopically the sd -shell 2-body effective interactions, the core energy and the sd -shell s.p. energies. Thus, the input for standard shell-model calculations can be determined microscopically by this approach. If the same procedure is then applied to 19-nucleon systems, the sd -shell 3-body effective interactions can also be obtained, indicating the importance of these 3-body effective interactions relative to the 2-body effective interactions. Applications to A = 19 and heavier nuclei with different intrinsic NN interactions will be presented and discussed. Supported by the US NSF under Grant No. 0854912, the US DOE under

Liquid–liquid equilibria study of the (water + phosphoric acid + hexyl or cyclohexyl acetate) systems at T = (298.15, 308.15, and 318.15) K: Measurement and thermodynamic modelling

International Nuclear Information System (INIS)

Ghanadzadeh Gilani, A.; Ghanadzadeh Gilani, H.; Shekarsaraee, S.; Nasiri-Touli, E.; Seyed Saadat, S.L.

2016-01-01

Highlights: • Tie line data for aqueous solutions of phosphoric acid with esters were obtained. • The LLE data were correlated using the UNIQUAC and NRTL models. • The quality of the LLE data was validated using the appropriate equations. • Separation factors were calculated for the chosen solvents. - Abstract: Liquid–liquid equilibrium (LLE) data for the (water + phosphoric acid + n-hexyl acetate or cyclohexyl acetate) ternary systems were determined at T = (298.15, 308.15 and 318.15) K and p = 101.3 kPa. The cloud point method was used to obtain the solubility and the Karl-Fischer, acidimetric titration, and refractive index methods were used to determine the tie-line values. Both the ternary systems exhibit type-1 behavior of LLE. The experimental values were regressed and acceptably correlated using the UNIQUAC and NRTL models. The reliability of the experimental tie lines was confirmed using the Othmer–Tobias plot. Experimental distribution coefficients and separation factors were fitted using the Kamlet–Taft LSER model. The influence of temperature on the biphasic area and separation factor was found to be minor. As a result, both the esters are suitable separating agents for aqueous phosphoric acid mixtures.

Effect of 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone on the corrosion of aged 18 Ni 250 grade maraging steel in phosphoric acid solution

International Nuclear Information System (INIS)

Poornima, T.; Nayak, Jagannath; Nityananda Shetty, A.

2011-01-01

Highlights: → DEABT as corrosion inhibitor for maraging steel in phosphoric acid. → Inhibition efficiency increases with increase in inhibitor concentration. → Inhibition efficiency decreases with increase in temperature. → Adsorption obeys Langmuir adsorption isotherm. - Abstract: 4-(N,N-diethylamino)benzaldehyde thiosemicarbazone (DEABT) was studied for its corrosion inhibition property on the corrosion of aged 18 Ni 250 grade maraging steel in 0.67 M phosphoric acid at 30-50 deg. C by potentiodynamic polarization, EIS and weight loss techniques. Inhibition efficiency of DEABT was found to increase with the increase in DEABT concentration and decrease with the increase in temperature. The activation energy E a and other thermodynamic parameters (ΔG ads 0 , ΔH ads 0 , ΔS ads 0 ) have been evaluated and discussed. The adsorption of DEABT on aged maraging steel surface obeys the Langmuir adsorption isotherm model and the inhibitor showed mixed type inhibition behavior.

Induced assembly and photoluminescence of lanthanum (Tb, Eu, Dy) complexes/ZnO/polyethylene glycol hybrid phosphors

Energy Technology Data Exchange (ETDEWEB)

Yan Bing [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China)]. E-mail: byan@tongji.edu.cn; Chen Xi [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China); Wu Jianhua [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China)

2007-08-31

Some novel kinds of hybrid phosphors were assembled with lanthanum (Tb, Eu, Dy) complexes (with four kinds of terbium complexes is 2,4-dihydroxybenzonic acid (DHBA), 1,10-phenanthroline (phen), acetylacetone (AA) and nicotinic acid (Nic), respectively) doped ZnO/PEG particles by co-precipitation approach derived from Zn(CH{sub 3}COO){sub 2} (Zn(AC){sub 2}), NaOH, PEG as precursors at room temperature. The characteristic luminescence spectra for f-f transitions of Tb{sup 3+}, Eu{sup 3+}, Dy{sup 3+} were observed. It is worthy to point out that ZnO is the excellent host for lanthanum ions by the assembly of PEG matrices.

Practical applications of phosphors

CERN Document Server

Yen, William M; Yamamoto, Hajime

2006-01-01

Drawn from the second edition of the best-selling Phosphor Handbook, Practical Applications of Phosphors outlines methods for the production of various phosphors and discusses a broad spectrum of applications. Beginning with methods for synthesis and related technologies, the book sets the stage by classifying and then explaining practical phosphors according to usage. It describes the operating principle and structure of phosphor devices and the phosphor characteristics required for a given device, then covers the manufacturing processes and characteristics of phosphors. The book discusses research and development currently under way on phosphors with potential for practical usage and touches briefly on phosphors that have played a historical role, but are no longer of practical use. It provides a comprehensive treatment of applications including lamps and cathode-ray tubes, x-ray and ionizing radiation, and for vacuum fluorescent and field emission displays and covers inorganic and organic electroluminescen...

Reanalysis information for eigenvalues derived from a differential equation analysis formulation. [for shell of revolution buckling

Science.gov (United States)

Thornton, W. A.; Majumder, D. K.

1974-01-01

The investigation reported demonstrates that in the case considered perturbation methods can be used in a straightforward manner to obtain reanalysis information. A perturbation formula for the buckling loads of a general shell of revolution is derived. The accuracy of the obtained relations and their range of application is studied with the aid of a specific example involving a particular stiffened shell of revolution.

Phenolic compounds and antioxidant activity of kernels and shells of Mexican pecan (Carya illinoinensis).

Science.gov (United States)

de la Rosa, Laura A; Alvarez-Parrilla, Emilio; Shahidi, Fereidoon

2011-01-12

The phenolic composition and antioxidant activity of pecan kernels and shells cultivated in three regions of the state of Chihuahua, Mexico, were analyzed. High concentrations of total extractable phenolics, flavonoids, and proanthocyanidins were found in kernels, and 5-20-fold higher concentrations were found in shells. Their concentrations were significantly affected by the growing region. Antioxidant activity was evaluated by ORAC, DPPH•, HO•, and ABTS•-- scavenging (TAC) methods. Antioxidant activity was strongly correlated with the concentrations of phenolic compounds. A strong correlation existed among the results obtained using these four methods. Five individual phenolic compounds were positively identified and quantified in kernels: ellagic, gallic, protocatechuic, and p-hydroxybenzoic acids and catechin. Only ellagic and gallic acids could be identified in shells. Seven phenolic compounds were tentatively identified in kernels by means of MS and UV spectral comparison, namely, protocatechuic aldehyde, (epi)gallocatechin, one gallic acid-glucose conjugate, three ellagic acid derivatives, and valoneic acid dilactone.

Thermoluminescent phosphor

Science.gov (United States)

Lasky, Jerome B.; Moran, Paul R.

1978-01-01

A thermoluminescent phosphor comprising LiF doped with boron and magnesium is produced by diffusion of boron into a conventional LiF phosphor doped with magnesium. Where the boron dopant is made to penetrate only the outer layer of the phosphor, it can be used to detect shallowly penetrating radiation such as tritium beta rays in the presence of a background of more penetrating radiation.

A new oxidimetric reagent-potassium dichromate in a strong phosphoric acid medium-VIII Potentiometric titration of molybdenum(VI) and vanadium(V).

Science.gov (United States)

Muralikrishna, U; Rao, G G

1968-01-01

A new titrimetric method is described for the determination of molybdenum(VI) involving prior reduction to Mo(V) with an excess of Fe(II) in a concentrated phosphoric acid solution, followed by titration with dichromate. The titration can be done at room temperature and without protective atmosphere. Uranium interferes, but vanadium may be determined simultaneously.

Antioxidative Peptides Derived from Enzyme Hydrolysis of Bone Collagen after Microwave Assisted Acid Pre-Treatment and Nitrogen Protection

Directory of Open Access Journals (Sweden)

Jin Sun

2010-11-01

Full Text Available This study focused on the preparation method of antioxidant peptides by enzymatic hydrolysis of bone collagen after microwave assisted acid pre-treatment and nitrogen protection. Phosphoric acid showed the highest ability of hydrolysis among the four other acids tested (hydrochloric acid, sulfuric acid and/or citric acid. The highest degree of hydrolysis (DH was 9.5% using 4 mol/L phosphoric acid with a ratio of 1:6 under a microwave intensity of 510 W for 240 s. Neutral proteinase gave higher DH among the four protease tested (Acid protease, neutral protease, Alcalase and papain, with an optimum condition of: (1 ratio of enzyme and substrate, 4760 U/g; (2 concentration of substrate, 4%; (3 reaction temperature, 55 °C and (4 pH 7.0. At 4 h, DH increased significantly (P < 0.01 under nitrogen protection compared with normal microwave assisted acid pre-treatment hydrolysis conditions. The antioxidant ability of the hydrolysate increased and reached its maximum value at 3 h; however DH decreased dramatically after 3 h. Microwave assisted acid pre-treatment and nitrogen protection could be a quick preparatory method for hydrolyzing bone collagen.

Synthesis of 2-phosphaadamantane derivatives

International Nuclear Information System (INIS)

Zemlyanoi, V.N.; Aleksandrov, A.M.; Kukhar', V.P.

1986-01-01

The authors describe the synthesis and properties of 2-phosphadamantane derivatives. For the synthesis of 2-phosphaadamantane derivatives they decided to use the methodology of the synthesis of 2-thiaadamantane. The IR spectra were determined on CHCl 3 solutions with a Specord 711R spectrometer, the PMR spectra were determined on Tesla BS-467 (60 MHz) and Bruker WP-200 (200 MHz) spectrometers, external standard hexamethyldisiloxane, the 31 P NMR spectra were determined on Tesla BS-487 C (30 MHz) and Bruker WP-200 (81 MHz) spectrometers, external standard 85% phosphoric acid, and the mass spectra were determined on an MS-1302 spectrometer

One-step hydrothermal synthesis of carboxyl-functionalized upconversion phosphors for bioapplications.

Science.gov (United States)

Yang, Jianping; Shen, Dengke; Li, Xiaomin; Li, Wei; Fang, Yin; Wei, Yong; Yao, Chi; Tu, Bo; Zhang, Fan; Zhao, Dongyuan

2012-10-22

In this paper, we report a facile one-step hydrothermal method to synthesize phase-, size-, and shape-controlled carboxyl-functionalized rare-earth fluorescence upconversion phosphors by using a small-molecule binary acid, such as malonic acid, oxalic acid, succinic acid, or tartaric acid as capping agent. The crystals, from nano- to microstructures with diverse shapes that include nanospheres, microrods, hexagonal prisms, microtubes, microdisks, polygonal columns, and hexagonal tablets, can be obtained with different reaction times, reaction temperatures, molar ratios of capping agent to sodium hydroxide, and by varying the binary acids. Fourier transform infrared, thermogravimetric analysis, and upconversion luminescence spectra measurements indicate that the synthesized NaYF(4):Yb/Er products with hydrophilic carboxyl-functionalized surface offer efficient upconversion luminescent performance. Furthermore, the antibody/secondary antibody conjugation can be realized by the carboxyl-functionalized surfaces of the upconversion phosphors, thus indicating the potential bioapplications of these kinds of materials. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Regio-, Diastereo-, and Enantioselective Nitroso-Diels-Alder Reaction of 1,3-Diene-1-carbamates Catalyzed by Chiral Phosphoric Acids.

Science.gov (United States)

Pous, Jonathan; Courant, Thibaut; Bernadat, Guillaume; Iorga, Bogdan I; Blanchard, Florent; Masson, Géraldine

2015-09-23

Chiral phosphoric acid-catalyzed asymmetric nitroso-Diels-Alder reaction of nitrosoarenes with carbamate-dienes afforded cis-3,6-disubstituted dihydro-1,2-oxazines in high yields with excellent regio-, diastereo-, and enantioselectivities. Interestingly, we observed that the catalyst is able not only to control the enantioselectivity but also to reverse the regioselectivity of the noncatalyzed nitroso-Diels-Alder reaction. The regiochemistry reversal and asynchronous concerted mechanism were confirmed by DFT calculations.

Rare earth phosphors and phosphor screens

International Nuclear Information System (INIS)

Buchanan, R.A.; Maple, T.G.; Sklensky, A.F.

1981-01-01

Advances in the use of stabilized rare earth phosphors and of conversion screens using these materials are examined. In particular the new phosphors discussed in this invention consist of oxybromides of yttrium, lanthanum and gadolinium with a luminescent activator ion stabilized by an oxychloride or oxyfluoride surface layer and the conversion screens include trivalent cerium as the activator ion. (U.K.)

Energetic and exergetic analysis of a steam turbine power plant in an existing phosphoric acid factory

International Nuclear Information System (INIS)

Hafdhi, Fathia; Khir, Tahar; Ben Yahyia, Ali; Ben Brahim, Ammar

2015-01-01

Highlights: • The operating mode of the factory and the power supply streams are presented. • Energetic Analysis of steam turbine power plant of an existing phosphoric acid factory. • Exergetic Analysis of each component of steam turbine power plant and the different heat recovery system. • Energy, exergy efficiency and irreversibility rates for the main components are determined. • The effect of the operating parameters on the plant performance are analyzed. - Abstract: An energetic and exergetic analysis is conducted on a Steam Turbine Power Plant of an existing Phosphoric Acid Factory. The heat recovery systems used in the different parts of the plant are also considered in the study. Mass, energy and exergy balances are established on the main compounds of the plant. A numerical code is established using EES software to perform the calculations required for the thermal and exergy plant analysis considering real variation ranges of the main operating parameters such as pressure, temperature and mass flow rate. The effects of theses parameters on the system performances are investigated. The main sources of irreversibility are the melters, followed by the heat exchangers, the steam turbine generator and the pumps. The maximum energy efficiency is obtained for the blower followed by the heat exchangers, the deaerator and the steam turbine generator. The exergy efficiency obtained for the heat exchanger, the steam turbine generator, the deaerator and the blower are 88%, 74%, 72% and 66% respectively. The effects of High Pressure steam temperature and pressure on the steam turbine generator energy and exergy efficiencies are investigated.

Isolation and structural characterization of sugarcane bagasse lignin after dilute phosphoric acid plus steam explosion pretreatment and its effect on cellulose hydrolysis

Science.gov (United States)

Jijiao Zeng; Zhaohui Tong; Letian Wang; J.Y. Zhu; Lonnie Ingram

2014-01-01

The structure of lignin after dilute phosphoric acid plus steam explosion pretreatment process of sugarcane bagasse in a pilot scale and the effect of the lignin extracted by ethanol on subsequent cellulose hydrolysis were investigated. The lignin structural changes caused by pretreatment were identified using advanced nondestructive techniques such as gel permeation...

Study on the kinetics of high-energy phosphates in myocardium by phosphorous nuclear magnetic resonance

Energy Technology Data Exchange (ETDEWEB)

Kusuoka, Hideo; Tsuneoka, Yutaka; Inoue, Michitoshi; Abe, Hiroshi [Osaka Univ. (Japan). Faculty of Medicine; Watari, Hiroshi

1982-12-01

Effect of artificial blood, FC 43 (Perfluorochemicals) on the kinetics of high-energy phosphate in the myocardium was evaluated by /sup 31/P-NMR which permits a continuous and non-invasive assessment of in vivo phosphorus compounds. Cardiac perfusion was carried out on a excised rat heart with a Krebs-Henseleit modified solution and FC 43 alternately. Under the normal condition, ischemic condition, and at second perfusion amounts of intramyocardial creatine phosphoric acid, ATP, and inorganic phosphorus were determined by /sup 31/P-NMR. Coronary flow was simultaneously estimated. The ischemic state due to interruption of perfusion resulted in a decrease in creatine phosphoric acid, which was associated with an increase in inorganic phosphorus and intracellular acidosis. No change of ATP amount was observed under ischemic state. With resumption of perfusion, the levels of creatine phosphoric acid and inorganic phosphorus rapidly returned to the normal. In the group of FC 43, coronary flow was 2.68 ml/min/g of the heart weight, about 1/2 of that of the Krebs-Henseleit group (5.68 ml/min/g of the heart weight). In controls, there was no difference between the two groups concerning creatine phosphoric acid level and recovery of creatine phospohric acid level after ischemia. These results showed that FC 43 supplies sufficient oxygen, and has no effect on the kinetics of energy in the myocardium.

Analysis and evaluation of the possibility of introducing phosphoric acid fuel cells

Science.gov (United States)

1991-03-01

Each step in the manufacture of fuel cells is reviewed. The possibility of cost reduction in the process is investigated. Additionally, the feasibility of providing financial assistance for fuel cell buyers is investigated. Also, the present status and the future outlook of fuel cell development are discussed. In Japan, phosphoric acid fuel cells are beginning demonstration testing. A 200 kW test plant, for commercial and remote island use, has finished its demonstration test favorably. The test run of an 11 mW plant, for the production of electric power, is being conducted by a private company. The manufacture of each of the fuel cell's subsystems is semi-automated at this time. The costs are estimated to be reduced to 60 - 80 percent of the present costs in a 10 mW/year plant and TO 50 - 60 percent of the present costs in a 100 mW/year plant.

Progress report on nitric-phosphoric acid oxidation

International Nuclear Information System (INIS)

Pierce, R.A.

1994-01-01

The purpose of this program has been to demonstrate a nitric-phosphoric acid destruction technology which can treat a heterogeneous waste stream. This technology is being developed to convert hazardous liquid and solid organics to inorganic gases and salts while simultaneously performing a surface decontamination of the noncombustible items. Pu-238 waste is an issue because it must be shipped to WIPP. However, the presence of organics and Pu-238 waste is an issue because it must be shipped to WIPP. However, the presence of organics and Pu-238 exceeds packaging requirements because of concerns of hydrogen generation. If the TRU can be separated from the organics, the allowable heat load of a container increases a factor of 25. More importantly, since the current shipping package is limited by volume and not heat loading, destroying the organic compounds and decontaminating noncombustible can potentially create a three-order magnitude decrease in the number of shipments that must be made to WIPP. The process envisioned will be configured to handle 1 million pounds (as of 12/91) of a wide range of solid TRU-contaminated waste of which 600,000 pounds is combustible. The process will oxidize the combustibles (a mixture of 14% cellulose, 3% rubber, 64% plastics, 9% absorbed oil, 4% resins and sludges, and 6% miscellaneous organics) without requiring separation from the 400,000 pounds of noncombustibles. The system is being developed to operate below 200 C at moderate pressures (0--15 psig). This report primarily discusses results obtained over the past 3 1/2 months and their impact on the feasibility of a pilot-scale system

Removal of mercury from water by carbonaceous sorbents derived from walnut shell

International Nuclear Information System (INIS)

Zabihi, M.; Ahmadpour, A.; Asl, A. Haghighi

2009-01-01

The adsorption ability of a powdered activated carbon (PAC) derived from walnut shell was investigated in an attempt to produce more economic and effective sorbent for the control of Hg(II) ion from industrial liquid streams. Carbonaceous sorbents derived from Iranian walnut shell (WS) were prepared by chemical activation method using ZnCl 2 as an activating reagent. To the best of our knowledge, this adsorbent was not used before for removing mercury from water. Adsorption of Hg(II) from aqueous solutions was carried out under different experimental conditions by varying treatment time, metal ion concentration, adsorbent amount, pH and solution temperature. It was determined that Hg(II) adsorption follows both Langmuir and Freundlich isotherms as well as pseudo-second-order kinetics. It was also shown that Hg(II) uptake decreases with increasing pH of the solution. The proper choice of preparation conditions resulted in a microporous activated carbon with 0.45 g/cm 3 density, 737 mg/g iodine number and 780 m 2 /g BET surface area. The monolayer sorption capacity of this optimum adsorbent was obtained as 151.5 mg/g.

Monoliths of activated carbon from coconut shell and impregnation with nickel and copper

International Nuclear Information System (INIS)

Giraldo, Liliana; Moreno, Juan

2008-01-01

A series of different monoliths of activated carbon were prepared from coconut shell By means of chemical activation with phosphoric acid at different concentrations Without using binders or plastics. The monolith that developed the biggest surface area was impregnated by humidic route with solutions of Ni and Cu at different molar relations. The structures were characterized by N2 adsorption at 77 K, and the morphology was explored by means of scanning electron microscopy. The carbonaceous materials obtained, Nickel-Copper-Monolith, were analyzed by Thermal Programmed Reduction (TPR). The experimental results indicated that the activation with the acid generated a micro porosity, with micropores volume between 0.40 and 0.81 cm 3 g-1 and surface areas between 703 and 1450 m 2 g-1, and a good mechanical properties. It shows that, both the copper and the nickel, are fixed to the monolith and TPR's results are interpreted when these molar relation are modified.

Development of a volumetric Analysis method to determine uranium in the loaded phosphoric acid and the loaded organic phase (DEHPA/TOPO)

International Nuclear Information System (INIS)

Shlewit, H.; Koudsi, Y.

2003-01-01

Rapid and reliable volumetric analysis method has been developed to determine uranium, on line, at uranium extraction unit from wet-process phosphoric acid, in aqueous and organic phases. This process enable up 300 mg of uranium to be determined in the presence of nitric acid, in a sample volume of up to at least 10 ml. The volume of the sample, the amounts of reagents added, the temperature of the reagents and the standing time of various stages were investigated to ensure that the conditions selected for the final procedure were reasonably non-critical

Optical property investigations of polystyrene capped Ca2P2O7:Dy3+ persistent phosphor

International Nuclear Information System (INIS)

Jain, Abhilasha; Kumar, Ashwini; Dhoble, S.J; Peshwe, D.R

2015-01-01

Highlights: • Synthesis of polymer capped pyrophosphate phosphors by citrate gel method. • Radiative lifetime is calculated from parameters of Judd-Ofelt theory and ICP-AES. • Reaction mechanism is discussed leading to high photoluminescence efficiency. • PL emission spectrum reveals broad band emission suitable for solid state lighting. - Abstract: By virtue of enhanced photosensivity, good optical response and better thermal stability, organic–inorganic hybrid materials are contemplated as one of the alternatives for designing advanced optoelectronic devices and innovative photonic applications. A novel inorganic organic hybrid Ca 2 P 2 O 7 :Dy 3+ phosphor has been fabricated by Pechini method. The optical property of synthesized phosphor is successfully altered by the in corporation of polystyrene sulfonic acid as capping agent in the colloidal solution. The phase purity and the average particle size of the prepared phosphor were calculated from X-ray diffraction (XRD) employing Debye Scherrer method. The morphological and chemical investigations were carried out through scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis. The radiative transitions are explained on the basis of Judd-Ofelt theory and on the basis of derived parameters, the radiative lifetime of persistent hybrid Ca 2 P 2 O 7 :Dy 3+ phosphor is calculated as 5.33 ms. This paper explores the mechanism leading to high photoluminescence efficiency using organic capping additives. The photoluminescence (PL) graphs reveal broad band emission at 482 nm (blue) and 573 nm (yellow) corresponding to 4 F 9/2 - 6 H 15/2 and 4 F 9/2 - 6 H 13/2 transitions of Dy 3+ , respectively. The Commission International De I-Eclairage (CIE) chromaticity co-ordinates were calculated from emission spectra and the values (x, y) were approaching to standard value of white emission. The synthesized pyrophosphate phosphors can thereby account in multiple potential applications

Cinnamic Acid Derivatives as Antidiabetics Agents

Directory of Open Access Journals (Sweden)

Teni Ernawati

2017-04-01

Full Text Available Diabetes mellitus is a metabolic disorder of carbohydrate metabolism. Treatment of type II diabetes is usually done by prescribing diet and exercise for the patient however it can also be treated with antidiabetic drugs. The purpose of this paper is to illustrate some cinnamic acid derivative compounds which are either isolated from natural materials or the results of the chemical synthesis. In addition, their biological activities as an agent of α-glucosidase inhibitors have also been evaluated. Chemically, cinnamic acid has three main functional groups:  first is the substitution on the phenyl group, second is the additive reaction into the α-β unsaturated, and third is the chemical reaction with carboxylic acid functional groups. Chemical aspects of cinnamic acid derivative compounds have received much attention in the research and development of drugs, especially modifications within three functional groups are very influential. In the last 10 years, a lot of research and development of cinnamic acid derivatives as inhibitors of the α-glucosidase enzyme has been done. One example of the research done in this field is the modification of para position in the structure of cinnamic acid and addition of alkyl groups in the carboxylic group which would increase the activity of the α-glucosidase enzyme therefore the level of inhibition is 100 times higher than that of cinnamic acid compound itself. The novelty of this review article is to focus on the antidiabetic activity of cinnamic acid derivatives.

Isolation of thermally stable cellulose nanocrystals by phosphoric acid hydrolysis.

Science.gov (United States)

Camarero Espinosa, Sandra; Kuhnt, Tobias; Foster, E Johan; Weder, Christoph

2013-04-08

On account of their intriguing mechanical properties, low cost, and renewable nature, high-aspect-ratio cellulose nanocrystals (CNCs) are an attractive component for many nanomaterials. Due to hydrogen bonding between their surface hydroxyl groups, unmodified CNCs (H-CNCs) aggregate easily and are often difficult to disperse. It is shown here that on account of ionic repulsion between charged surface groups, slightly phosphorylated CNCs (P-CNCs, average dimensions 31 ± 14 × 316 ± 127 nm, surface charge density = 10.8 ± 2.7 mmol/kg cellulose), prepared by controlled hydrolysis of cotton with phosphoric acid, are readily dispersible and form stable dispersions in polar solvents such as water, dimethyl sulfoxide, and dimethylformamide. Thermogravimetric analyses reveal that these P-CNCs exhibit a much higher thermal stability than partially sulfated CNCs (S-CNCs), which are frequently employed, but suffer from limited thermal stability. Nanocomposites of an ethylene oxide-epichlorohydrin copolymer and H-CNCs, S-CNCs, and P-CNCs were prepared, and their mechanical properties were studied by dynamic mechanical thermal analysis. The results show that P-CNCs offer a reinforcing capability that is comparable to that of H-CNCs or S-CNCs.

Effect of Phosphoric Acid Concentration on the Optical Properties of Partially Phosphorylated PVA Complexes

Directory of Open Access Journals (Sweden)

Asmalina Mohamed Saat

2014-01-01

Full Text Available Partially phosphorylated polyvinyl alcohol (PPVA films were prepared at five mole ratios of phosphoric acid (PA using solution casting technique. The optical properties of the PPVA films were examined using UV-visible (UV and photoluminescence (PL spectroscopy. The UV absorption spectra reveal that the absorption peaks are blue-shifted with an increase in PA concentration added to the pure PVA. The PL spectra show the presence of peaks which are characteristic of isotactic (389–398, 460–462 nm, syndiotactic (418–420 nm, and atactic (440–446 nm configurations of the PPVA. The results also show the peak of O–P–O bonding at a wavelength range of 481–489 nm.

Study of phosphorous based resins for the uptake of plutonium from H2SO4 based analytical waste

International Nuclear Information System (INIS)

Seshadri, H.; Mohandas, Jaya; Srinivasan, S.; Kumar, T.; Rajan, S.K.

2006-01-01

This study indicates that phosphorous based resins can be conveniently employed for the uptake of plutonium from analytical wastes even in strong acid media and also in the presence of diverse ions like silver and chromium. It is also evident that phosphorous based resins have proved to be efficient even in sulphuric acid medium

Complexes of Cd sup 2 sup +, U(O sub 2 ) sup 2 sup + and Th sup 4 sup + at radiotracer levels with phosphoric acid

International Nuclear Information System (INIS)

Bouhlassa, S.; El-Yahyaoui, A.; Brillard, L.; Hussonnois, M.; Guillaumont, R.

1994-01-01

In this work, we have turn to account the radiochemical techniques in order to investigate the complexation of Cd sup 2 sup +, U(O sub 2) sup 2 sup + and Th sup 2 sup +, at strength Mu=0,2, in various phosphoric media characterized by C sub ( H sub 3 P O sub 4) <= 4 M and 0.7 <= pH <= 4. The method chosen for this purpose is the liquid-liquid extraction of radioisotopes at tracer scale, with di(2-ethyl hexyl) phosphoric acid dissolved in benzene. The radionuclides used are Cd-109, U-233, U-230 and Th-227. Their distribution between the two phases are established by alpha or gamma spectrometric analysis. The analysis of the distribution data allows to define, in addition of species extracted in organic phase, the nature of phosphoric complexes which take place in aqueous media. Stability constants of these complexes and associated thermodynamic data are determined. 2 tabs.; 2 refs. (author)

Electrochemical reduction of oxygen on small platinum particles supported on carbon in concentrated phosphoric acid. 2. Effects of teflon content in the catalyst layer and baking temperature of the electrode

Energy Technology Data Exchange (ETDEWEB)

Maoka, T.

1988-03-01

A relation between hydrophobicity (or wettability) of a porous gas diffusion electrode for use in a phosphoric acid fuel cell and its cathode performance (activity toward electrochemical oxygen reduction) was examined. The hydrophobicity of the gas diffusion electrode was regulated by changing either the amount of Teflon (PTFE) content in the catalyst layer or baking temperature of the electrode. The Tafel slope or electrochemical oxygen reduction became twice as high as that of the ordinary electrode when the wettability of electrode toward phosphoric acid was high. This fact supports a flooded agglomerate model as the mode of this type of porous gas diffusion electrode.

Au@Ag core-shell nanocubes with finely tuned and well-controlled sizes, shell thicknesses, and optical properties.

Science.gov (United States)

Ma, Yanyun; Li, Weiyang; Cho, Eun Chul; Li, Zhiyuan; Yu, Taekyung; Zeng, Jie; Xie, Zhaoxiong; Xia, Younan

2010-11-23

This paper describes a facile method for generating Au@Ag core-shell nanocubes with edge lengths controllable in the range of 13.4-50 nm. The synthesis involved the use of single-crystal, spherical Au nanocrystals of 11 nm in size as the seeds in an aqueous system, with ascorbic acid serving as the reductant and cetyltrimethylammonium chloride (CTAC) as the capping agent. The thickness of the Ag shells could be finely tuned from 1.2 to 20 nm by varying the ratio of AgNO(3) precursor to Au seeds. We also investigated the growth mechanism by examining the effects of seeds (capped by CTAC or cetyltrimethylammonium bromide(CTAB)) and capping agent (CTAC vs CTAB) on both size and shape of the resultant core-shell nanocrystals. Our results clearly indicate that CTAC worked much better than CTAB as a capping agent in both the syntheses of Au seeds and Au@Ag core-shell nanocubes. We further studied the localized surface plasmon resonance properties of the Au@Ag nanocubes as a function of the Ag shell thickness. By comparing with the extinction spectra obtained from theoretical calculations, we derived a critical value of ca. 3 nm for the shell thickness at which the plasmon excitation of the Au cores would be completely screened by the Ag shells. Moreover, these Au@Ag core-shell nanocubes could be converted into Au-based hollow nanostructures containing the original Au seeds in the interiors through a galvanic replacement reaction.

Decommissioning of Phosphoric Acid Purification Facility, PT Petrokimia Gresik

International Nuclear Information System (INIS)

Zainus Salimin; Nanang TS; Zaid, Ach.; Chotimah; Karyono

2008-01-01

Decommissioning of phosporic acid purification facility was the administrative and technical actions taken to allow the removal of some or all of the regulatory control from that facility exploit the phosphoric acid containing uranium. The site location of facility was cleaned up as the clean previous site (green land) for another site project utilization. Decommissioning activities covers the draining of solution or solid powder of remaining process on the equipment, decontamination of site location and equipment wall, dismantling of equipment, decontamination of equipment after dismantling, and decontamination of concrete floor and wall. Uranium contaminated liquid waste and organic solution was treated by bio-oxidation process using bacteria. Remaining solid powder from process (28 drums), contaminated material and equipment after decontamination (60 drums of fire brick, 31 pieces of equipment cut, 2 drums of ashes, 10 drums of active sludge from bio-oxidation process) and concrete splinter of 10 drums of 200 l volume per drum are the radioactive waste that must be sent to Radioactive Waste Technology Centre for its treatment. The non contaminated material and equipment (908 ton) can be reused for reprocessing, some of non contaminated sludge (14.4 m 3 ) and all of non contaminated filtrate water (353 m 3 ) from bio-oxidation process with toxic matters qualification which comply to the its limit values are released on the effluent release drain system of the plant. Clearance level utilizing for filtering contaminated material or equipment was an activity concentration of 1 Bq/g, surface contamination of 1 Bq/cm 2 , effective dose on the 50 cm distance from surface of contaminated material of 0.5 μSv/h (BAPETEN Regulation Letter No. 1459A/P101/PIBN/2008). Limit values for toxic matter are pH 6-9, COD 100 ppm and BOD 50 ppm (Gov. Regulation of East Java No. 45 year of 2002). (author)

Chitin Extraction from Crustacean Shells Using Biological Methods – A Review

Directory of Open Access Journals (Sweden)

Wassila Arbia

2013-01-01

Full Text Available After cellulose, chitin is the most widespread biopolymer in nature. Chitin and its derivatives have great economic value because of their biological activities and their industrial and biomedical applications. It can be extracted from three sources, namely crustaceans, insects and microorganisms. However, the main commercial sources of chitin are shells of crustaceans such as shrimps, crabs, lobsters and krill that are supplied in large quantities by the shellfish processing industries. Extraction of chitin involves two steps, demineralisation and deproteinisation, which can be conducted by two methods, chemical or biological. The chemical method requires the use of acids and bases, while the biological method involves microorganisms. Although lactic acid bacteria are mainly applied, other microbial species including proteolytic bacteria have also been successfully implemented, as well as mixed cultures involving lactic acid-producing bacteria and proteolytic microorganisms. The produced lactic acid allows shell demineralisation, since lactic acid reacts with calcium carbonate, the main mineral component, to form calcium lactate.

Study of the solubility of yttrium, praseodymium, neodymium, and gadolinium sulfates in the presence of sodium and potassium in sulfuric-phosphoric acid solutions at 20 deg C

International Nuclear Information System (INIS)

Lokshin, Eh.P.; Tareeva, O.A.; Kashulina, T.G.

2007-01-01

The solubility of yttrium, praseodymium, neodymium, and gadolinium sulfates in the presence of sodium and potassium ions and the composition of solid phases were studied at 20 deg C in relation to the concentration of acids in sulfuric acid, phosphoric acid, and sulfuric-phosphoric acid solutions containing up to 36 wt % H 2 SO 4 and 33.12 g 1 -1 H 3 PO 4 . The formation of double sulfates of praseodymium and neodymium with sodium and potassium ions, as well as of gadolinium sulfate with sodium ions of the composition 1 : 1 was revealed. In water at 20 deg C, the solubility products of PrNa(SO 4 ) 2 ·H 2 O, NdNa(SO 4 ) 2 ·H 2 O, GdNa(SO 4 ) 2 ·H 2 O, PrK(SO 4 ) 2 ·H 2 O, and NdK(SO 4 ) 2 ·H 2 O are found to be 7.28x10 -8 , 7.84x10 -8 , 3.09x10 -6 , 3.02x10 -6 , and 1.70x10 -6 , respectively [ru

Solvent Extraction of Rare Earths by Di-2 Ethylhexyl Phosphoric Acid

International Nuclear Information System (INIS)

Srinuttrakul, Wannee; Kranlert, Kannika; Kraikaew, Jarunee; Pongpansook, Surasak; Chayavadhanangkur, Chavalek; Kranlert, Kannika

2004-10-01

Solvent extraction has been widely applied for individual rare earth separation because the separation time is rapid and a large quantity of products is obtained. In this work, this technique was utilized to extract mixed rare earths, obtained from monazite digestion process. Di-2-ethylhexyl phosphoric acid (D2EHPA) was used as an extractant. The factors affected the extraction including HNO 3 concentration in mixed rare earth nitrate solution and the amount of D2EHPA were studied. The appropriate concentrations of HNO 3 and D2EHPA were found to be 0.01 and 1.5 M, respectively. From the result of equilibrium curve study, it was observed that heavy rare earths were extracted more efficient than light rare earths. A 6-stage continuous countercurrent solvent extraction was simulated for rare earth extraction. The optimum ratio of solvent to feed solution (S/F) was 2. Because of the high cost of D2EHPA, 1.0 M of D2EHPA was suitable for the rare earth extraction by the continuous countercurrent solvent extraction

One-pot synthesis of Pd-Pt@Pd core-shell nanocrystals with enhanced electrocatalytic activity for formic acid oxidation

KAUST Repository

Yuan, Qiang

2014-01-01

Well-defined Pd-Pt@Pd core-shell nanocrystals with a Pd-Pt alloy core and a conformal Pd shell of ~2-3 nm were directly synthesized through a one-pot, aqueous solution approach without any preformed Pd or Pt seeds. These Pd-Pt@Pd core-shell nanocrystals show an enhanced electrocatalytic activity for formic acid oxidation compared with commercial Pd black. This journal is © 2014 The Royal Society of Chemistry.

A study on the kinetics of high-energy phosphates in myocardium by phosphorous nuclear magnetic resonance

International Nuclear Information System (INIS)

Kusuoka, Hideo; Tsuneoka, Yutaka; Inoue, Michitoshi; Abe, Hiroshi; Watari, Hiroshi.

1982-01-01

Effect of artificial blood, FC 43 (Perfluorochemicals) on the kinetics of high-energy phosphate in the myocardium was evaluated by 31 P-NMR which permits a continuous and non-invasive assessment of in vivo phosphorus compounds. Cardiac perfusion was carried out on a excised rat heart with a Krebs-Henseleit modified solution and FC 43 alternately. Under the normal condition, ischemic condition, and at second perfusion amounts of intramyocardial creatine phosphoric acid, ATP, and inorganic phosphorus were determined by 31 P-NMR. Coronary flow was simultaneously estimated. The ischemic state due to interruption of perfusion resulted in a decrease in creatine phosphoric acid, which was associated with an increase in inorganic phosphorus and intracellular acidosis. No change of ATP amount was observed under ischemic state. With resumption of perfusion, the levels of creatine phosphoric acid and inorganic phosphorus rapidly returned to the normal. In the group of FC 43, coronary flow was 2.68 ml/min/g of the heart weight, about 1/2 of that of the Krebs-Henseleit group (5.68 ml/min/g of the heart weight). In controls, there was no difference between the two groups concerning creatine phosphoric acid level and recovery of creatine phospohric acid level after ischemia. These results showed that FC 43 supplies sufficient oxygen, and has no effect on the kinetics of energy in the myocardium. (Ueda, J.)

New Trident Molecule with Phosphoric Acid Functionality for Trivalent Rare Earth Extraction

Directory of Open Access Journals (Sweden)

Keisuke Ohto

2017-11-01

Full Text Available Tripodal extraction reagent with three phosphoric acid groups, together with the corresponding monopodal molecule has been prepared to investigate some metals extraction behavior, in particular, trivalent rare earth elements (REEs. The tripodal reagent exhibited extremely high selectivity for metals with high valency such as Zr(IV, In(III, Lu(III, and Fe(III. Tripodal reagent also exhibited exceptionally high extraction ability compared with the corresponding monopodal one in the extraction of trivalent rare earths. The result for the stoichiometry of tripodal reagent to heavy rare earths showed the inflection point between Er (2:1 for a ligand with ion and Tm (1:1. The extraction reactions were determined for all rare earths with both reagents. The extraction equilibrium constants (Kex, the separation factors (β, half pH values (pH1/2, difference half pH values (ΔpH1/2 for extraction of REEs with both reagents are estimated.

Rare Earth Doped Lanthanum Calcium Borate Polycrystalline Red Phosphors

Directory of Open Access Journals (Sweden)

H. H. Xiong

2014-01-01

Full Text Available Single-phased Sm3+ doped lanthanum calcium borate (SmxLa2−xCaB10O19, SLCB, x=0.06 polycrystalline red phosphor was prepared by solid-state reaction method. The phosphor has two main excitation peaks located at 398.5 nm and 469.0 nm, which are nicely in accordance with the emitting wavelengths of commercial near-UV and blue light emitting diode chips. Under the excitation of 398.0 nm, the dominant red emission of Sm3+ in SLCB phosphor is centered at 598.0 nm corresponding to the transition of 4G5/2 → 6H7/2. The Eu3+ fluorescence in the red spectral region is applied as a spectroscopic probe to reveal the local site symmetry in the host lattice and, hence, Judd-Ofelt parameters Ωt  (t=2, 4 of Eu3+ in the phosphor matrix are derived to be 3.62×10-20 and 1.97×10-20 cm2, indicating a high asymmetrical and strong covalent environment around rare earth luminescence centers. Herein, the red phosphors are promising good candidates employed in white light emitting diodes (LEDs illumination.

Investigation of uranium (VI) extraction mechanisms from phosphoric and sulfuric media by {sup 31}P-NMR

Energy Technology Data Exchange (ETDEWEB)

Fries, B.; Marie, C.; Pacary, V.; Berthon, C.; Miguirditchian, M.; Charbonnel, M.C. [CEA, Centre de Marcoule, Nuclear Energy Divison, RadioChemistry and Processes Department - DRCP, F-30207 Bagnols-sur-Ceze (France); Mokhtari, H. [AREVA Mines, Process and Analysis Department - SEPA, F-87250 Bessines-sur-Gartempe (France)

2016-07-01

Phosphate rocks contain uranium (∼1000 ppm on average) and are considered as a secondary source for uranium production. Uranium extraction using DEHCNPB (butyl-1-[N,N-bis(2-ethylhexyl)carbamoyl]nonyl phosphonic acid, a bifunctional cationic extractant) has been studied to better understand mechanism differences depending on the original acidic solution (phosphoric or sulfuric). Solvent extraction batch experiments were carried out and the organic phases were probed using {sup 31}P-NMR. This technique enabled to demonstrate that phosphoric acid is poorly extracted by DEHCNPB ([H{sub 3}PO{sub 4}]{sub org} < 2 mM), using direct quantification in the organic phase by {sup 31}P-NMR spectra integration. Moreover, in the presence of uranium in the initial phosphoric acid solution, uranyl extraction by DEHCNPB competes with H{sub 3}PO{sub 4} extraction. Average stoichiometries of U(VI)-DEHCNPB complexes in organic phases were also determined using slope analysis on uranium distribution data. Uranium seems to be extracted from a phosphoric medium by two extractant molecules, whereas more than three DEHCNPB on average would be necessary to extract uranium from a sulfuric medium. Thus, uranium is extracted according to different mechanisms depending on the nature of the initial solution. (authors)

Hyaluronic acid/poly(lactic-co-glycolic acid) core/shell fiber meshes loaded with epigallocatechin-3-O-gallate as skin tissue engineering scaffolds.

Science.gov (United States)

Lee, Eun Ji; Lee, Jong Ho; Jin, Linhua; Jin, Oh Seong; Shin, Yong Cheol; Sang, Jin Oh; Lee, Jaebeom; Hyon, Suong-Hyu; Han, Dong-Wook

2014-11-01

In this study, hyaluronic acid (HA)/poly(lactic-co-glycolic acid, PLGA) core/shell fiber meshes loaded with epigallocatechin-3-O-gallate (EGCG) (HA/PLGA-E) for application to tissue engineering scaffolds for skin regeneration were prepared via coaxial electrospinning. Physicochemical properties of HA/PLGA-E core/shell fiber meshes were characterized by SEM, Raman spectroscopy, contact angle, EGCG release profiling and in vitro degradation. Biomechanical properties of HA/PLGA-E meshes were also investigated by a tensile strength test. SEM images showed that HA/PLGA-E fiber meshes had a three-dimensional interconnected pore structure with an average fiber diameter of about 1270 nm. Raman spectra revealed that EGCG was uniformly dispersed in the PLGA shell of meshes. HA/PLGA-E meshes showed sustained EGCG release patterns by controlled diffusion and PLGA degradation over 4 weeks. EGCG loading did not adversely affect the tensile strength and elastic modulus of HA/PLGA meshes, while increased their hydrophilicity and surface energy. Attachment of human dermal fibroblasts on HA/PLGA-E meshes was appreciably increased and their proliferation was steadily retained during the culture period. These results suggest that HA/PLGA-E core/shell fiber meshes can be potentially used as scaffolds supporting skin regeneration.

Effects of Different Solvents on the Surface Acidic Oxygen-containing Functional Groups on Xanthoceras sorbifolia Shell

Directory of Open Access Journals (Sweden)

Linan Liu

2014-03-01

Full Text Available This study reports the preparation of a novel biomaterial from a forestry residue - Xanthoceras sorbifolia shell (XSS - by solvent modification. The effects of acid and base (hydrochloric acerbic, acetic acid, sodium hydroxide, ammonia water and some organic solvents (ethanol, acetone, ethyl acetate, chloroform, petroleum ether, and n-hexane on the surface acidic functional groups (SAFGs on XSS were investigated. The amount of SAFGs was quantified using acid and alkali chemical titration methods, and the characteristics of virgin XSS were compared with treated ones by FT-IR spectroscopy. It was found that acid solutions can increase the concentration of SAFGs, while alkaline solutions reduce it. The XSS treated in 0.5 M HCl has the largest number of total acidic functional groups and phenolic hydroxyl groups. The shell extracted with 2 M acetic acid has the highest concentration of carboxyl. The SAFG contents were remarkably increased by treatments with ethanol and acetone, due to the outstanding enhancement of phenolic hydroxyl. These changes in the SAFGs of XSS brought about by treatments with various solutions could be a theoretical foundation for modifying this residue to create a new type of highly efficient absorbent material.

Treatment alternatives of liquid radioactive waste containing uranium in phosphoric acid

International Nuclear Information System (INIS)

Bustamante Escobedo, Mauricio

2003-01-01

The UGDR, receives annually 100 [l] of liquid radioactive waste containing, highly acid (pH=0) uranium in phosphoric acid from the Laboratory of Chemical Analysis. This waste must be chemically and radiologically decontaminated before it can be discharged in accordance with local environmental standards. Chemical precipitation and evaporation test were carried out to define the operating conditions for the radiological decontamination of this radioactive waste and to obtain a solid waste that can be conditioned in a cement matrix. The evaporation process generates excellent rates of volume reduction, over 80%, but generates a pulp that is hard handle when submitted to a drying process. Chemical precipitation generates good results for decontaminating these solutions and reducing volume (above 50%) to obtain a uranium free effluent. The treatment with calcium carbonate generated an effluent with a low concentration of polluting agents. A preliminary test was carried out condition these solids in a cement matrix, using ratios of 0.45 waste/cement and 2 of water/cement. The mix prepared with waste from the sodium hydroxide treatment had low mechanical resistance resulting from the saline incrustations. The waste from the calcium carbonate treatment was very porous due to the water evaporation from the highly exothermic reaction between the waste and the cement. The mix of the calcium carbonate generated waste and the cement matrix needs to be optimized, since it generates favorable conditions for adhering with the cement matrix (au)

Titrimetric determination of uranium in low-grade ores by the ferrous ion-phosphoric acid reduction method

International Nuclear Information System (INIS)

Hitchen, A.; Zechanowitsch, G.

1980-01-01

The modification and extension of the U.S.A.E.C. ferrous ion-phosphoric acid reduction method for the determination of uranium in high-grade or relatively pure material to a method for the determination of uranium with a high accuracy and precision, in ores containing 0.004 to 7% U is described. It is simple, rapid and requires no prior separations from elements that, in other methods, frequently interfere. For sample materials having very high concentrations of interfering elements, a prior concentration step using extraction with tri-n-octylphosphine oxide is described, but it is shown that, for most low-grade ores, this step is unnecessary. (author)

Entropy as a measure of the performance of phosphor materials used in medical imaging radiation detectors

International Nuclear Information System (INIS)

Cavouras, D.; Kandarakis, I.; Maris, T.; Panayiotakis, G.S.; Nomicos, C.D.

2001-01-01

In information theory, entropy expresses the information gain obtained after detection of a signal concerning the state of a parameter of interest. In this study, entropy has been expressed in terms of physical quantities (emitted optical fluence and MTF) related to the imaging performance of phosphor materials, which are employed in medical imaging radiation detectors. Four phosphor materials, used in the form of laboratory-prepared fluorescent layers (screens), were compared on the basis of their entropy performance. Measurements were performed using 30- and 80-kVp X-ray beams often employed in X-ray imaging. Results showed that phosphor materials with high density and effective atomic number exhibit high entropy performance, especially at the higher X-ray tube voltage of 80 kVp. Entropy values are also affected by the type of activator, which determines the intrinsic X-ray-to-light conversion efficiency, and the spectrum of emitted light. The proximity of the incident X-ray quanta energy to the energy of the K-shell threshold for photoelectric absorption is an additional important factor which increases entropy. This effect was more apparent in the performance of yttrium-based phosphors at the lower voltage of 30 kVp. (orig.)

Comparison of Buffer Effect of Different Acids During Sandstone Acidizing

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben; Hamid, Mohamed Ali

2015-01-01

The most important concern of sandstone matrix acidizing is to increase the formation permeability by removing the silica particles. To accomplish this, the mud acid (HF: HCl) has been utilized successfully for many years to stimulate the sandstone formations, but still it has many complexities. This paper presents the results of laboratory investigations of different acid combinations (HF: HCl, HF: H 3 PO 4 and HF: HCOOH). Hydrofluoric acid and fluoboric acid are used to dissolve clays and feldspar. Phosphoric and formic acids are added as a buffer to maintain the pH of the solution; also it allows the maximum penetration of acid into the core sample. Different tests have been performed on the core samples before and after the acidizing to do the comparative study on the buffer effect of these acids. The analysis consists of permeability, porosity, color change and pH value tests. There is more increase in permeability and porosity while less change in pH when phosphoric and formic acids were used compared to mud acid. From these results it has been found that the buffer effect of phosphoric acid and formic acid is better than hydrochloric acid. (paper)

A new oxidimetric reagent: potassium dichromate in a strong phosphoric acid medium-VI Potentiometric titration of vanadium(III) alone and in mixture with vanadium(IV).

Science.gov (United States)

Rao, G G; Rao, P K

1966-09-01

Vanadium(III) can be titrated at room temperature with potassium dichromate in an 8-12M phosphoric acid medium. Two potential breaks are observed in 12M phosphoric add with 0.2N potassium dichromate, the first corresponding to the oxidation of vanadium(III) to vanadium(IV) and the second to the oxidation of vanadium(IV) to vanadium(V). In titrations with 0.05N dichromate only the first break in potential is clearly observed. The method has been extended to the titration of mixtures of vanadium(III) and vanadium(IV). Conditions have also been found for the visual titration of vanadium(III) using ferroln or barium diphenylamine sulphonate as indicator.

Comparative analysis of amino acids and amino-acid derivatives in protein crystallization

International Nuclear Information System (INIS)

Ito, Len; Shiraki, Kentaro; Yamaguchi, Hiroshi

2010-01-01

New types of aggregation suppressors, such as amino acids and their derivatives, were focused on as fourth-component additives. Data were obtained that indicated that the additives promote protein crystallization. Optimal conditions for protein crystallization are difficult to determine because proteins tend to aggregate in saturated solutions. This study comprehensively evaluates amino acids and amino-acid derivatives as additives for crystallization. This fourth component of the solution increases the probability of crystallization of hen egg-white lysozyme in various precipitants owing to a decrease in aggregation. These results suggest that the addition of certain types of amino acids and amino-acid derivatives, such as Arg, Lys and esterified and amidated amino acids, is a simple method of improving the success rate of protein crystallization

Transesterification of palm oil to biodiesel by using waste obtuse horn shell-derived CaO catalyst

International Nuclear Information System (INIS)

Lee, Seik Lih; Wong, Yong Chen; Tan, Yen Ping; Yew, Sook Yan

2015-01-01

Highlights: • Cost effective CaO catalyst derived from waste obtuse horn shells. • The optimum biodiesel yield, 86.75% can be achieved under mild reaction conditions. • The catalyst can be reused up to 3 times with biodiesel yield more than 70%. • Deactivation of catalyst was due to leaching of CaO and pores-filling. - Abstract: The calcium oxide catalysts derived from waste obtuse horn shells were utilized in the transesterification of palm oil into biodiesel. This environment-friendly catalyst is thermally activated at 800 °C for 3 h. The resulting CaO catalyst was characterized using thermogravimetric analysis (TGA), X-ray diffraction (XRD), temperature-programmed desorption of CO 2 (TPD-CO 2 ), Brunauer–Emmett–Teller (BET) surface area analysis, and scanning electron microscopy (SEM). XRD patterns of calcined catalyst showed intense peaks of calcium oxide, consistent with XRF results that revealed calcium is the major element present in the obtuse horn shells. High calcination temperature (800 °C) tended to promote agglomeration of fine crystals, resulted in a smaller surface area (0.07 m 2 /g) as examined by BET. Catalytic activities in the transesterification process had been investigated using one-variable-at-a-time technique. The optimum palm oil conversion was 86.75% under reaction conditions of 6 h, 5 wt.% of catalyst amount and methanol to oil ratio of 12:1. Reusability of this waste shell derived catalyst was examined and results showed that the prepared catalysts are able to be reused up to 3 times with conversion of more than 70% after the third cycles. Although the reusability may not be excellent at the moment, it is still in the exploratory study. More efforts were done to improve its properties and stability

Radiological assessment occupational radionuclides in a phosphoric acid plant; Evaluacion radiologica ocupacional y distribucion de radionucleidos en una planta de acido fosforico

Energy Technology Data Exchange (ETDEWEB)

Bolivar, J. P.; Garcia-Tenorio, R.

2008-07-01

On the frame of a research project devoted to the control of the exposure due to natural radiation in several NORM industries located at the South of Spain, a detailed to the production of phosphoric acid has been performed. In addition, the behaviour along the mentioned process of the different radionuclides involved has been analysed. It has been concluded that the effective dose which can be received by the workers of the plant is clearly below 1 mSv/year. And it has been demonstrated that the main route of occupational exposure corresponds to the external radiation due mainly to the permanent presence of a radioactive contamination source in different zones of the plant. This contamination source is associated to the presence of scales in the inner surfaces of pipes and equipment as well as to the presence of sludges in the phosphoric acid storage tanks, which in both cases contain elevated concentrations of 226{sup R}a. Moreover, the 222{sup R}n concentrations inside the plant do not overpass 100 Bq/m{sup 3}, which not constitutes a radiological problem. (Author) 9 refs.

Phosphor scintillator structure

International Nuclear Information System (INIS)

Cusano, D.A.; Prener, J.S.

1980-01-01

A method of fabricating scintillators is described in which the phosphor is distributed within the structure in such a way as to enhance the escape of the visible wavelength radiation that would otherwise be dissipated within the scintillator body. Two embodiments of the present invention are disclosed: one in which the phosphor is distributed in a layered structure and another in which the phosphor is dispersed throughout a transparent matrix. (U.K.)

On the Reaction of Carbonyl Diphosphonic Acid with Hydroxylamine and O-alkylhydroxylamines: Unexpected Degradation of P-C-P Bridge.

Science.gov (United States)

Khomich, Olga A; Yanvarev, Dmitry V; Novikov, Roman A; Kornev, Alexey B; Puljulla, Elina; Vepsäläinen, Jouko; Khomutov, Alex R; Kochetkov, Sergey N

2017-06-23

Derivatives of methylenediphosphonic acid possess wide spectra of biological activities and are used in enzymology as research tools as well as in practical medicine. Carbonyl diphosphonic acid is a promising starting building block for synthesis of functionally substituted methylenediphosphonates. Investigation of the interaction of carbonyl diphosphonic acid with hydroxylamine clearly demonstrates that it is impossible to isolate oxime within the pH range 2-12, while only cyanophosphonic and phosphoric acids are the products of the fast proceeding Beckmann-like fragmentation. In the case of O -alkylhydroxylamines, corresponding alcohols are found in the reaction mixtures in addition to cyanophosphonic and phosphoric acids. Therefore, two residues of phosphonic acid being attached to a carbonyl group provide new properties to this carbonyl group, making its oximes very unstable. This principally differs carbonyl diphosphonic acid from structurally related phosphonoglyoxalic acid and other α-ketophosphonates.

Comparison of arsenic acid with phosphoric acid in the interaction with a water molecule and an alkali/alkaline-earth metal cation.

Science.gov (United States)

Park, Sung Woo; Kim, Chang Woo; Lee, Ji Hyun; Shim, Giwoong; Kim, Kwang S

2011-10-20

Recently, Wolfe-Simon has discovered a bacterium which is able to survive using arsenic(V) rather than phosphorus(V) in its DNA. Thus it is important to investigate some important structural and chemical similarities and dissimilarities between phosphate and arsenate. We compared the monohydrated structures and the alkali/alkaline-earth metal (Na(+), K(+), Mg(2+) and Ca(2+)) complexes of the arsenic acid/anions with those of the phosphoric acid/anions [i.e., H(m)PO(4)(-(3-m)) vs H(m)AsO(4)(-(3-m)) (m = 1-3)]. We carried out geometry optimization along with harmonic frequency calculations using ab initio calculations. Despite the increased van der Waals radius of As, the hydrated structures of both P and As systems show very close similarity (within 0.25 Å in the P/As···O(water) distance and within a few kJ/mol in binding energy) because of the increased induction energies by more polar arsenic acid/anons and slightly increased dispersion energy by a larger size of the As atom. In the metal complexes, the arsenic acid has a slightly larger binding distance (by 0.07-1.0 Å) and weaker binding energy because the As(V) ion has a slightly larger radius than the P(V) ion, and the electrostatic interaction is the dominating feature in these systems.

Red-emitting LaOF:Eu{sup 3+} phosphors: Synthesis, structure and their Judd–Ofelt analysis for LED applications

Energy Technology Data Exchange (ETDEWEB)

Dhananjaya, N., E-mail: ndhananjayas@gmail.com [Department of Physics, B. M. S. Institute of Technology and Management, Bangalore 560064 (India); Shivakumara, C.; Saraf, Rohit [Solid State and Structural Chemistry Unit, Indian Institute of Science, Bangalore 560012 (India); Nagabhushana, H. [C. N. R. Rao Center for Advanced Materials, Tumkur University, Tumkur 572103 (India)

2016-03-15

Highlights: • Red-emitting LaOF:Eu{sup 3+} phosphors were synthesized via facile solid state route. • Judd–Ofelt intensity parameters and radiative properties were determined from PL data. • CIE color coordinates of LaOF:Eu{sup 3+} phosphor is close to the commercial red phosphors. • Eu{sup 3+}-activated LaOF phosphor is a potential candidate for the production of red component in white LEDs. - Abstract: In the present study, we have synthesized a series of La{sub 1−x}Eu{sub x}OF (0.01 ≤ x ≤ 0.09) phosphors by the conventional solid-state reaction route at relatively low temperature (500 °C) and shorter duration of 2 h. The compounds were crystallized in the rhombohedral structure with the space group R-3m (No. 166). Upon UV excitation (254 nm), the photoluminescence spectra exhibit characteristic luminescence {sup 5}D{sub 0} → {sup 7}F{sub J} (J = 1, 2, 3, and 4) intra-4f shell Eu{sup 3+} ion transitions. An intense red emission peak at 610 nm was observed due to electric dipole ({sup 5}D{sub 0} → {sup 7}F{sub 2}) transition. Judd–Ofelt theory was employed to evaluate various radiative parameters such as radiative emission rates, lifetime, branching and asymmetry ratios. CIE color coordinates confirmed the red emission of the phosphors. The luminescent results reveal that LaOF:Eu{sup 3+} phosphor can be used as potential candidate for developing red component in white LED applications.

Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system

International Nuclear Information System (INIS)

Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

2013-01-01

Highlights: • Recycling of rare earth metals from fluorescent lamps was conducted by ionic liquid-mediated extraction. • Acid leaching from a waste phosphor powder was carried out using sulfuric and nitric acids. • An ionic liquid was used as extracting solvent for the rare earth metals. • Selective extraction of rare earth metals from leach solutions was attained. •The extracting ionic liquid phase was recyclable in the recovery process. -- Abstract: The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid–liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system

Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system

Energy Technology Data Exchange (ETDEWEB)

Yang, Fan; Kubota, Fukiko; Baba, Yuzo [Department of Applied Chemistry, Graduate School of Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Kamiya, Noriho [Department of Applied Chemistry, Graduate School of Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Center for Future Chemistry, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Goto, Masahiro, E-mail: m-goto@mail.cstm.kyushu-u.ac.jp [Department of Applied Chemistry, Graduate School of Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Center for Future Chemistry, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan)

2013-06-15

Highlights: • Recycling of rare earth metals from fluorescent lamps was conducted by ionic liquid-mediated extraction. • Acid leaching from a waste phosphor powder was carried out using sulfuric and nitric acids. • An ionic liquid was used as extracting solvent for the rare earth metals. • Selective extraction of rare earth metals from leach solutions was attained. •The extracting ionic liquid phase was recyclable in the recovery process. -- Abstract: The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid–liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system.

Acid distribution in phosphoric acid fuel cells

Energy Technology Data Exchange (ETDEWEB)

Okae, I.; Seya, A.; Umemoto, M. [Fuji Electric Co., Ltd., Chiba (Japan)

1996-12-31

Electrolyte acid distribution among each component of a cell is determined by capillary force when the cell is not in operation, but the distribution under the current load conditions had not been clear so far. Since the loss of electrolyte acid during operation is inevitable, it is necessary to store enough amount of acid in every cell. But it must be under the level of which the acid disturbs the diffusion of reactive gases. Accordingly to know the actual acid distribution during operation in a cell is very important. In this report, we carried out experiments to clarify the distribution using small single cells.

An efficient synthesis of tetramic acid derivatives with extended conjugation from L-Ascorbic Acid

Directory of Open Access Journals (Sweden)

Bisht Surendra S

2006-12-01

Full Text Available Abstract Background Tetramic acids with polyenyl substituents are an important class of compounds in medicinal chemistry. Both solid and solution phase syntheses of such molecules have been reported recently. Thiolactomycin, a clinical candidate for treatment of tuberculosis has led to further explorations in this class. We have recently developed an efficient synthesis of tetramic acids derivatives from L- ascorbic acid. In continuation of this work, we have synthesised dienyl tetramic acid derivatives. Results 5,6-O-Isopropylidene-ascorbic acid on reaction with DBU led to the formation of tetronolactonyl allyl alcohol, which on oxidation with pyridinium chlorochromate gave the respective tetranolactonyl allylic aldehydes. Wittig olefination followed by reaction of the resulting tetranolactonyl dienyl esters with different amines resulted in the respective 5-hydroxy lactams. Subsequent dehydration of the hydroxy lactams with p-toluene sulphonic acid afforded the dienyl tetramic acid derivatives. All reactions were performed at ambient temperature and the yields are good. Conclusion An efficient and practical method for the synthesis of dienyl tetramic acid derivatives from inexpensive and easily accessible ascorbic acid has been developed. The compounds bear structural similarities to the tetramic acid based polyenic antibiotics and thus this method offers a new and short route for the synthesis of tetramic acid derivatives of biological significance.

Extraction of Tetravalent Uranium by Certain Acidic Organophosphorus Extractants from Phosphate Medium

International Nuclear Information System (INIS)

Daoud, J.A.; Zeid, M.M.; Aly, H.F.

1998-01-01

The extraction of U(IV) by octylphenyl acid phosphate (OPAP) or di-2-ethylhexyl phosphoric acid (HDEHP) in kerosene from phosphoric acid was carried out. The effect of extractant, phosphoric acid, uranium, Fe(II) and Fe(III) concentration on the extraction process was separately investigated. The effect of different reagents and temperature on the stripping of U(IV) was also investigated. The results obtained for the extraction of U(IV) by HDEHP showed that the extraction with the increase in HDEHP and Fe(III) concentration while it decreases with the increase in phosphoric acid, uranium and Fe(II) concentration. In case of extraction with OPAP, the extraction of U(IV) was found to decrease with the phosphoric acid, Fe(II) and initial uranium concentration while the increase in OPAP concentration slightly affected the extraction. The use of high phosphoric acid concentration as stripper at low temperature was found to give the best stripping results

Process for the removal of acid forming gases from exhaust gases and production of phosphoric acid

Science.gov (United States)

Chang, Shih-Ger; Liu, David K.

1992-01-01

Exhaust gases are treated to remove NO or NO.sub.x and SO.sub.2 by contacting the gases with an aqueous emulsion or suspension of yellow phosphorous preferably in a wet scrubber. The addition of yellow phosphorous in the system induces the production of O.sub.3 which subsequently oxidizes NO to NO.sub.2. The resulting NO.sub.2 dissolves readily and can be reduced to form ammonium ions by dissolved SO.sub.2 under appropriate conditions. In a 20 acfm system, yellow phosphorous is oxidized to yield P.sub.2 O.sub.5 which picks up water to form H.sub.3 PO.sub.4 mists and can be collected as a valuable product. The pressure is not critical, and ambient pressures are used. Hot water temperatures are best, but economics suggest about 50.degree. C. The amount of yellow phosphorus used will vary with the composition of the exhaust gas, less than 3% for small concentrations of NO, and 10% or higher for concentrations above say 1000 ppm. Similarly, the pH will vary with the composition being treated, and it is adjusted with a suitable alkali. For mixtures of NO.sub.x and SO.sub.2, alkalis that are used for flue gas desulfurization are preferred. With this process, better than 90% of SO.sub.2 and NO in simulated flue gas can be removed. Stoichiometric ratios (P/NO) ranging between 0.6 and 1.5 were obtained.

EPR and optical absorption studies of Cu{sup 2+} doped L-histidinium dihydrogen phosphate–phosphoric acid single crystal

Energy Technology Data Exchange (ETDEWEB)

Prabakaran, R.; Sheela, K. Juliet; Rosy, S. Margret [Department of Physics, Gandhigram Rural Institute—Deemed University, Gandhigram, Dindigul-624302, Tamilnadu (India); Radha Krishnan, S.; Shanmugam, V.M. [CSIR-Central Electrochemical Research Institute, Karaikudi-630006, Tamilnadu (India); Subramanian, P., E-mail: psmanian_gri@yahoo.com [Department of Physics, Gandhigram Rural Institute—Deemed University, Gandhigram, Dindigul-624302, Tamilnadu (India)

2014-02-01

The EPR spectra of Cu{sup 2+} in L-histidinium dihydrogen phosphate phosphoric acid at room temperature reveal the presence of two magnetically inequivalent Cu{sup 2+} sites in the lattice. The principal values of the g- and A-tensors indicate existence of rhombic symmetry around the Cu{sup 2+} ion. From the direction cosines of the principal values of the g- and A-tensors, the locations of Cu{sup 2+} in the lattice have been identified as substitutional sites. Optical absorption study shows four bands confirm the rhombic symmetry. Photoluminescence study also confirms the rhombic symmetry around the ions.

Electron-beam-pumped phosphors

International Nuclear Information System (INIS)

Goldhar, J.; Krupke, W.F.

1985-01-01

Electron-beam excitation of solid-state scintillators, or phosphors, can result in efficient generation of visible light confined to relatively narrow regions of the spectrum. The conversion efficiency can exceed 20%, and, with proper choice of phosphors, radiation can be obtained anywhere from the near infrared (IR) to the near ultraviolet (UV). These properties qualify the phosphors as a potentially useful pump source for new solid-state lasers. New phosphors are being developed for high-brightness television tubes that are capable of higher power dissipation. Here, an epitaxial film of fluorescing material is grown on a crystalline substrate with good thermal properties. For example, researchers at North American Philips Laboratories have developed a cerium-doped yttrium aluminum garnet (YAG) grown on a YAG substrate, which has operated at 1 A/cm 2 at 20 kV without observed thermal quenching. The input power is higher by almost two orders of magnitude than that which can be tolerated by a conventional television phosphor. The authors describe tests of these new phosphors

High temperature thermometric phosphors

Science.gov (United States)

Allison, Stephen W.; Cates, Michael R.; Boatner, Lynn A.; Gillies, George T.

1999-03-23

A high temperature phosphor consists essentially of a material having the general formula LuPO.sub.4 :Dy.sub.(x),Eu.sub.y) wherein: 0.1 wt %.ltoreq.x.ltoreq.20 wt % and 0.1 wt %.ltoreq.y.ltoreq.20 wt %. The high temperature phosphor is in contact with an article whose temperature is to be determined. The article having the phosphor in contact with it is placed in the environment for which the temperature of the article is to be determined. The phosphor is excited by a laser causing the phosphor to fluoresce. The emission from the phosphor is optically focused into a beam-splitting mirror which separates the emission into two separate emissions, the emission caused by the dysprosium dopant and the emission caused by the europium dopent. The separated emissions are optically filtered and the intensities of the emission are detected and measured. The ratio of the intensity of each emission is determined and the temperature of the article is calculated from the ratio of the intensities of the separate emissions.

Complexes of salicylic acid and its derivatives

Energy Technology Data Exchange (ETDEWEB)

Tel' zhenskaya, P N; Shvarts, E M [AN Latvijskoj SSR, Riga. Inst. Neorganicheskoj Khimii

1977-01-01

A generalization and systematization have been made of literature data on complexing of various elements, including beryllium, cadmium, boron, indium, rare-earth elements, actinides, and transition elements with salicylic acid and it derivatives (amino-, nitro- and halosalicylic acids). The effect of the position and nature of the substitute, in the case of salicylic acid derivatives, on the complexing process is discussed. Certain physicochemical properties of the complexes under consideration are described along with data indicative of their stability.

Bond strength of compomers to dentin using acidic primers.

Science.gov (United States)

Tate, W H; You, C; Powers, J M

1999-10-01

To determine the in vitro bond strengths of seven compomer/bonding agent restorative systems to human dentin. Seven compomer/bonding agents were bonded to human dentin, stored in water at 37 degrees C for 24 hours, and debonded in tension. Bonding conditions were with and without phosphoric acid etching, with and without the use of combined primer/bonding agents, and under moist and wet bond interfaces. Without phosphoric acid etching, F2000/F2000 Compomer Primer/Adhesive and F2000/Single Bond Dental Adhesive System were less sensitive to dentin wetness. With moist dentin, bond strengths of Dyract/Prime & Bond 2.1, Dyract AP/Prime & Bond 2.1, Hytac/OSB light-curing, one-component bonding agent, F2000/Single Bond, and Freedom/STAE single component light-cured dentin/enamel adhesive system, were improved with phosphoric acid etching. Also, with moist dentin, the bond strength of F2000/F2000 Compomer Primer/Adhesive in the 3M Clicker dispensing system was higher without phosphoric acid etching, whereas bonds of Compoglass/Syntac Single-component were not affected by phosphoric acid etching. Bonding did not occur without primer/bonding agent, regardless of surface condition or use of phosphoric acid etching.

Analytic first derivatives for a spin-adapted open-shell coupled cluster theory: Evaluation of first-order electrical properties

Energy Technology Data Exchange (ETDEWEB)

Datta, Dipayan, E-mail: datta@uni-mainz.de; Gauss, Jürgen, E-mail: gauss@uni-mainz.de [Institut für Physikalische Chemie, Johannes Gutenberg-Universität Mainz, Duesbergweg 10-14, D-55128 Mainz (Germany)

2014-09-14

An analytic scheme is presented for the evaluation of first derivatives of the energy for a unitary group based spin-adapted coupled cluster (CC) theory, namely, the combinatoric open-shell CC (COSCC) approach within the singles and doubles approximation. The widely used Lagrange multiplier approach is employed for the derivation of an analytical expression for the first derivative of the energy, which in combination with the well-established density-matrix formulation, is used for the computation of first-order electrical properties. Derivations of the spin-adapted lambda equations for determining the Lagrange multipliers and the expressions for the spin-free effective density matrices for the COSCC approach are presented. Orbital-relaxation effects due to the electric-field perturbation are treated via the Z-vector technique. We present calculations of the dipole moments for a number of doublet radicals in their ground states using restricted open-shell Hartree-Fock (ROHF) and quasi-restricted HF (QRHF) orbitals in order to demonstrate the applicability of our analytic scheme for computing energy derivatives. We also report calculations of the chlorine electric-field gradients and nuclear quadrupole-coupling constants for the CCl, CH{sub 2}Cl, ClO{sub 2}, and SiCl radicals.

Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system.

Science.gov (United States)

Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

2013-06-15

The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid-liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system. Copyright © 2013 Elsevier B.V. All rights reserved.

Phosphoric acid doped membranes based on Nafion®, PBI and their blends – Membrane preparation, characterization and steam electrolysis testing

DEFF Research Database (Denmark)

Aili, David; Hansen, Martin Kalmar; Pan, Chao

2011-01-01

Proton exchange membrane steam electrolysis at temperatures above 100 °C has several advantages from thermodynamic, kinetic and engineering points of view. A key material for this technology is the high temperature proton exchange membrane. In this work a novel procedure for preparation of Nafion......® and polybenzimidazole blend membranes was developed. Homogeneous binary membranes covering the whole composition range were prepared and characterized with respect to chemical and physiochemical properties such as water uptake, phosphoric acid doping, oxidative stability, mechanical strength and proton conductivity...

Evaluation of efficient glucose release using sodium hydroxide and phosphoric acid as pretreating agents from the biomass of Sesbania grandiflora (L.) Pers.: A fast growing tree legume.

Science.gov (United States)

Mund, Nitesh K; Dash, Debabrata; Barik, Chitta R; Goud, Vaibhav V; Sahoo, Lingaraj; Mishra, Prasannajit; Nayak, Nihar R

2017-07-01

Sesbania grandiflora (L.) Pers. is one of the fast growing tree legumes having the efficiency to produce around 50tha -1 above ground dry matters in a year. In this study, biomass of 2years old S. grandiflora was selected for the chemical composition, pretreatments and enzymatic hydrolysis studies. The stem biomass with a wood density of 3.89±0.01gmcm -3 contains about 38% cellulose, 12% hemicellulose and 28% lignin. Enzymatic hydrolysis of pretreated biomass revealed that phosphoric acid (H 3 PO 4 ) pretreated samples even at lower cellulase loadings [1 Filter Paper Units (FPU)], could efficiently convert about 86% glucose, while, even at higher cellulase loadings (60FPU) alkali pretreated biomass could convert only about 58% glucose. The effectiveness of phosphoric acid pretreatment was also supported by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and Fourier transform infrared spectroscopy (FTIR) analysis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of amino acids and amino acid derivatives on crystallization of hemoglobin and ribonuclease A

International Nuclear Information System (INIS)

Ito, Len; Kobayashi, Toyoaki; Shiraki, Kentaro; Yamaguchi, Hiroshi

2008-01-01

The effect of the addition of amino acids and amino acid derivatives on the crystallization of hemoglobin and ribonuclease A has been evaluated. The results showed that certain types of additives expand the concentration conditions in which crystals are formed. Determination of the appropriate conditions for protein crystallization remains a highly empirical process. Preventing protein aggregation is necessary for the formation of single crystals under aggregation-prone solution conditions. Because many amino acids and amino acid derivatives offer a unique combination of solubility and stabilizing properties, they open new avenues into the field of protein aggregation research. The use of amino acids and amino acid derivatives can potentially influence processes such as heat treatment and refolding reactions. The effect of the addition of several amino acids, such as lysine, and several amino acid derivatives, such as glycine ethyl ester and glycine amide, on the crystallization of equine hemoglobin and bovine pancreatic ribonuclease A has been examined. The addition of these amino acids and amino acid derivatives expanded the range of precipitant concentration in which crystals formed without aggregation. The addition of such additives appears to promote the crystallization of proteins

Effect of amino acids and amino acid derivatives on crystallization of hemoglobin and ribonuclease A

Energy Technology Data Exchange (ETDEWEB)

Ito, Len, E-mail: len@ksc.kwansei.ac.jp; Kobayashi, Toyoaki [School of Science and Technology, Kwansei Gakuin University, 2-1 Gakuen, Sanda, Hyogo 669-1337 (Japan); Shiraki, Kentaro [Institute of Applied Physics, University of Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki 305-8573 (Japan); Yamaguchi, Hiroshi [School of Science and Technology, Kwansei Gakuin University, 2-1 Gakuen, Sanda, Hyogo 669-1337 (Japan)

2008-05-01

The effect of the addition of amino acids and amino acid derivatives on the crystallization of hemoglobin and ribonuclease A has been evaluated. The results showed that certain types of additives expand the concentration conditions in which crystals are formed. Determination of the appropriate conditions for protein crystallization remains a highly empirical process. Preventing protein aggregation is necessary for the formation of single crystals under aggregation-prone solution conditions. Because many amino acids and amino acid derivatives offer a unique combination of solubility and stabilizing properties, they open new avenues into the field of protein aggregation research. The use of amino acids and amino acid derivatives can potentially influence processes such as heat treatment and refolding reactions. The effect of the addition of several amino acids, such as lysine, and several amino acid derivatives, such as glycine ethyl ester and glycine amide, on the crystallization of equine hemoglobin and bovine pancreatic ribonuclease A has been examined. The addition of these amino acids and amino acid derivatives expanded the range of precipitant concentration in which crystals formed without aggregation. The addition of such additives appears to promote the crystallization of proteins.

Macroporous Activated Carbon Derived from Rapeseed Shell for Lithium–Sulfur Batteries

Directory of Open Access Journals (Sweden)

Mingbo Zheng

2017-10-01

Full Text Available Lithium–sulfur batteries have drawn considerable attention because of their extremely high energy density. Activated carbon (AC is an ideal matrix for sulfur because of its high specific surface area, large pore volume, small-size nanopores, and simple preparation. In this work, through KOH activation, AC materials with different porous structure parameters were prepared using waste rapeseed shells as precursors. Effects of KOH amount, activated temperature, and activated time on pore structure parameters of ACs were studied. AC sample with optimal pore structure parameters was investigated as sulfur host materials. Applied in lithium–sulfur batteries, the AC/S composite (60 wt % sulfur exhibited a high specific capacity of 1065 mAh g−1 at 200 mA g−1 and a good capacity retention of 49% after 1000 cycles at 1600 mA g−1. The key factor for good cycling stability involves the restraining effect of small-sized nanopores of the AC framework on the diffusion of polysulfides to bulk electrolyte and the loss of the active material sulfur. Results demonstrated that AC materials derived from rapeseed shells are promising materials for sulfur loading.

Core-shell microspheres with porous nanostructured shells for liquid chromatography.

Science.gov (United States)

Ahmed, Adham; Skinley, Kevin; Herodotou, Stephanie; Zhang, Haifei

2018-01-01

The development of new stationary phases has been the key aspect for fast and efficient high-performance liquid chromatography separation with relatively low backpressure. Core-shell particles, with a solid core and porous shell, have been extensively investigated and commercially manufactured in the last decade. The excellent performance of core-shell particles columns has been recorded for a wide range of analytes, covering small and large molecules, neutral and ionic (acidic and basic), biomolecules and metabolites. In this review, we first introduce the advance and advantages of core-shell particles (or more widely known as superficially porous particles) against non-porous particles and fully porous particles. This is followed by the detailed description of various methods used to fabricate core-shell particles. We then discuss the applications of common silica core-shell particles (mostly commercially manufactured), spheres-on-sphere particles and core-shell particles with a non-silica shell. This review concludes with a summary and perspective on the development of stationary phase materials for high-performance liquid chromatography applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Water Pollutants Adsorption through an Enhanced Activated Carbon Derived from Agriculture Waste

Directory of Open Access Journals (Sweden)

Mojtaba Fazeli

2016-09-01

Full Text Available Background & Aims of the Study: A high nitrate and arsenic concentration in water resources represent a potential risk to the environment and public health. The present work improved a chemo-physically modified activated carbon derived from walnut shells as an adsorbent to improve nitrate and arsenic removal ability from water. Materials & Methods: To increase removal efficiency, activated carbon surface characteristics were improved by acidification. Chemical activation was achieved when the carbon was mixed with water and 5% (v/v phosphoric acid. After adsorbent preparation, the contact time, pH and the initial concentration were studied as variables. Results:  The effective pH for adsorption onto activated carbon was 6.5. The results indicated that 70 s and 3 mins was the sufficient time to attain equilibrium for a maximum removal efficiency of 78.44% and 98% for nitrate and arsenic, respectively. The adsorption capacity of the adsorbent was 10.60 mg nitrate/g carbon and 120 μg arsenic/g carbon. Removal obeyed the Langmuir isotherm and pseudo-second-order kinetic model. Conclusion: The results showed a noticeable improvement in activated walnut-shell carbon absorbance (improvement in crystalline structure, chemical bonds, and morphology of micropores by chemo-physical activation. Chemo-physical activation increased the surface area of the adsorbent from 1067 to 1437 m2g‒1 and decreased the mean pore size from 3.28 to 2.08 nm. The characterization results showed the major reasons of adsorption could be structure, size and distributions of pores, high surface area and chemical bonds.

Comparative effects of dietary sea urchin shell powder and feed additives on meat quality and fatty acid profiles of broiler breast meat

Directory of Open Access Journals (Sweden)

Sam Churl Kim

2015-08-01

Full Text Available This study was a small pen trial in which we investigated comparative effects of dietary sea urchin shell powder and feed additives on meat quality and fatty acid profiles of broiler breast meat. A total of 108 male broilers were assigned to 3 groups (control, 1% sea urchin shell powder, and 1% feed additives with 3 replicates of 12 chicks per pen in a completely randomized design for 28 days. The following parameters have been investigated: proximate composition (DM, CP, EE, and ash, physicochemical properties (pH, TBARS, cooking loss and DPPH radical scavenging, meat color and fatty acid profiles. No remarkable effects between treatment and storage day were observed for proximate composition, physicochemical properties, meat color and fatty acid profiles. In conclusion, diets with 1% sea urchin shell powder have the ability to increase DPPH radical scavenging and unsaturated fatty acid, indicating an opportunity for partial diet substitution in comparison with 1% feed additives.

Determination of the O/M ratios of polynary uranium oxides by Ce(IV)-Fe(II) back titration after dissolution in mixed sulphuric and phosphoric acids.

Science.gov (United States)

Fujino, T; Sato, N; Yamada, K

1996-01-01

Uranium (IV) in polynary uranium oxides is determined after the solid has been dissolved in a warm mixed solution of sulphuric and phosphoric acids containing excess Ce(IV). The latter is titrated with a Fe(II) standard solution using ferroin as indicator. This method is especially effective for (mixed) uranium oxides which are difficult to dissolve in hot Ce(IV) sulphuric acid. The standard deviation of the determined x value in polynary oxides is estimated to be below +/- 0.004 for samples of 10-30 mg.

On the complexing of phosphoric acid vinyl esters with praseodymium (3) and europium (3) nitrates in acetonitrile

International Nuclear Information System (INIS)

Goryushko, A.G.; Gololobov, Yu.G.; Boldeskul, A.E.; Oganesyan, A.S.; Yartsev, V.G.

1990-01-01

By the methods of electron, IR and PMR spectroscopy interaction of vinyl esters of phosphoric acid with praseodymium (3) and europium (3) nitrates in acetonitrile solutions has been studied. It is shown that the character of metal-ligand interaction is determined by chemical nature of the ligands: for a compound of ionic structure partially covalent bond is formed, and for a compound of betaine structure the interaction has mainly dipole character. Addition of molecule with betaine structure to praseodymium nitrate causes a change in geometry of Pr 3+ close surrounding and increase in its coordination number. The possibility of formation of the complex with metal-ligand ratio equal to 1:3 is shown

Evaluation of human dental loss caused by carbamide peroxide bleacher compared with phosphoric acid conditioning - radioactive method; Avaliacao da perda dental humana com o uso do clareador peroxido de carbamida comparado ao condicionamento com acido fosforico - metodo radiometrico

Energy Technology Data Exchange (ETDEWEB)

Adachi, Eduardo Makoto; Yousseff, Michel Nicolau [Sao Paulo Univ., SP (Brazil). Faculdade de Odontologia. Dept. de Dentistica; Saiki, Mitiko [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil). Lab. de Analise por Ativacao Neutronica

2002-07-01

The radiometric method was applied to the evaluation of dental loss caused by carbamide peroxide when it is applied on the surface layers of enamel and dentin tissues. Also the dental loss caused by the etching with 37% phosphoric acid procedure used in aesthetic restoration was assessed for comparison with those results obtained. The tooth samples irradiated with a P standard in a thermal neutron flux of the nuclear reactor were placed in contact with 10% carbamide peroxide or with 37% phosphoric acid solution. The radioactivity of {sup 32} P transferred from the radioactive teeth to the bleaching gel or to etching acid was measured using a Geiger Muller detector to calculate the mass of P removed in this treatment and losses were calculated after obtaining their P concentrations. Results obtained indicated that enamel and dentin exposed to carbamide peroxide bleaching agent lose phosphorus. The extent of enamel loss was smaller than that obtained for dentin. In the case of acid etching, there was no difference between the results obtained for enamel and dentin loss. Also the dentin loss obtained after a treatment of 30 applications of 10% carbamide peroxide was the same magnitude of that one application of 37% phosphoric acid. (author)