WorldWideScience

Sample records for shearing electrorheological er

  1. Temperature and shear rate characteristics of electrorheological gel applied to a clutch

    Koyanagi, K; Takata, Y; Motoyoshi, T; Oshima, T; Kakinuma, Y; Anzai, H; Sakurai, K

    2013-01-01

    This investigation reports the physical characteristics of electrorheological (ER) gels, which are a type of functional material having controlled surface friction. We previously developed slip clutches using ER gels sandwiched between electrodes, and verified their responses and controllability. We newly report the temperature and shear rate characteristics of ER gel in this study because the input and output electrodes of the clutch continuously slip past each other. While the temperature of ER gels increased when energized, the shear stress hardly changed. Instead, wearing and adaptation to the electrode affect the property. The shear rate hardly affected the shear stress in the high-shear-rate region. Conversely, the shear stress depended on the shear rate in the lower region.

  2. Electrorheological (ER) Fluids: A Research Needs Assessment

    1993-05-01

    is given as line (g). Experimental results a correspond to polyaniline in silicone oil, e.c•,=36 (Gow 1990); * hollow silica spheres in corn oil ye...Malishauskas, 1981) (Fig. 18b). In Minsk, we have designed a new model of a screw valve (Shulman, 1978b). Its electrodes are fabricated in the form of...Takimoto, both of whom were very gracious. Dr. Takimoto is primarily involved in ER research. I was not shown any facilities while there, primarily

  3. Electrorheology of aniline-oligomer suspensions under oscillatory shear

    Mrlík, M.; Pavlínek, V.; Almajdalawi, S.; Saha, P.; Bober, Patrycja; Stejskal, Jaroslav

    2013-01-01

    Roč. 412, č. 1 (2013), 012007_1-012007_6 ISSN 1742-6588. [International Conference on Electrorheological Fluids and Magnetorheological Suspensions /13./ - ERMR2012. Ankara, 02.07.2012-06.07.2012] R&D Projects: GA ČR GA202/09/1626 Institutional support: RVO:61389013 Keywords : electrorheology * polyaniline * conducting polymer Subject RIV: BK - Fluid Dynamics

  4. Analysis of the yielding behavior of electrorheological suspensions by controlled shear stress experiments

    Pavlínek, V.; Sáha, P.; Perez-Gonzales, K.; de Vargas, L.; Stejskal, Jaroslav; Quadrat, Otakar

    2006-01-01

    Roč. 16, 1-2 (2006), s. 14-18 ISSN 1430-6395 R&D Projects: GA ČR GA202/06/0419 Institutional research plan: CEZ:AV0Z40500505 Keywords : electrorheology * yield stress * suspensions * polyaniline Subject RIV: CD - Macromolecular Chemistry

  5. Electrorheology of a zeolite/silicone oil suspension under dc fields

    Tian, Yu; Meng, Yonggang; Wen, Shizhu

    2001-01-01

    The electrorheology of electrorheological (ER) fluids based on zeolite and silicone oil under dc fields was investigated at room temperature. ER fluids with volume fractions of 27% and 30% were prepared and tested. When a 5 kV/mm dc field was applied, shear yield stress of 26.7 kPa was obtained for the latter. The ER fluid with a higher volume fraction of zeolite had a higher current density and a higher shear yield stress under the same electric field. Compared with other ER fluids based on zeolite particles with low shear yield stress, the zeolite employed by us was found to have high dielectric constant and conductivity. The high permittivity mismatch and the high conductivity mismatch of the components of the fluids were considered responsible for the high shear yield stress. [copyright] 2001 American Institute of Physics

  6. Fabrication and characterization of mesoporous TiO2/polypyrrole-based nanocomposite for electrorheological fluid

    Wei Chuan; Zhu Yihua; Jin Yi; Yang Xiaoling; Li Chunzhong

    2008-01-01

    Mesoporous TiO 2 /polypyrrole (PPy)-based nanocomposite for electrorheological fluid was synthesized through one-pot method. By exploiting the combination conductivity of PPy and high dielectric constant of TiO 2 , the ER fluid exhibited an enhanced effect. The shear stress was 3.3 times as high as that of mesoporous TiO 2 . Powder X-ray diffraction (XRD), TEM and Fourier transform infrared (FT-IR) spectroscopy were employed to characterize the as-made samples. Using a modified rotational viscometer, the electrorheological effect was measured. Dielectric spectra were also given to explain the mechanism

  7. Electrorheology of graphene oxide.

    Zhang, Wen Ling; Liu, Ying Dan; Choi, Hyoung Jin; Kim, Sang Guk

    2012-04-01

    Novel polarizable graphene oxide (GO) particles with oxidized groups on their edge and basal planes were prepared by a modified Hummers method, and their electro-responsive electrorheological (ER) characteristics when dispersed in silicone oil were examined with and without an electric field applied. The fibrillation phenomenon of this GO-based electro-responsive fluid was also observed via an optical microscope under an applied electric field. Both flow curves and dielectric spectra of the ER fluid were measured using a rotational rheometer and a LCR meter, respectively. Its viscoelastic properties of both storage and loss moduli were also examined using a vertical oscillation rheometer equipped with a high voltage generator, finding that the GO-based smart ER system behaves as a viscoelastic material under an applied electric field.

  8. Physics of Nontraditional Electrorheological and Magnetorheological Fluids

    Gu, G. Q.; Tao, R.

    Nontraditional electrorheology (ER) and magnetorheology (MR) are new areas. It started with high demands, such as reducing the viscosity of crude oil and suppressing turbulence to improve crude oil flow in pipelines. Normally, these two goals conflict each other. When the viscosity is reduced, Reynolds number goes up, and the turbulence would get worse. The non-traditional ER and MR have provided unconventional technologies to solve such issues. Different from traditional ER and MR, where the strong electric field or magnetic field is applied in the direction perpendicular to the flow or shearing, the fluid can even be solidified as the viscosity increases dramatically. In nontraditional ER and MR, the electric field or magnetic field is applied in the direction parallel to the flow, the particles are aggregated into short chains along the flow direction by the field, and the fluid viscosity becomes anisotropic. Along the flow direction, the viscosity is reduced, while in the directions perpendicular to the flow, the viscosity is dramatically increased. Thus the turbulence is suppressed; the flow becomes laminar and is further improved by the reduced viscosity along the flow direction. The original conflicted two goals can now be accomplished simultaneously. The new physics began to produce big impacts on energy, food industry, and medical science.

  9. Analysis of giant electrorheological fluids.

    Seo, Youngwook P; Seo, Yongsok

    2013-07-15

    The yield stress dependence on electric field strength for giant electrorheological (GER) fluids over the full range of electric fields was examined using Seo's scaling function which incorporated both the polarization and the conductivity models. If a proper scaling was applied to the yield stress data to collapse them onto a single curve, the Seo's scaling function could correctly fit the yield stress behavior of GER suspensions, even at very high electric field strengths. The model predictions were also compared with recently proposed Choi et al.'s model to allow a consideration of the universal framework of ER fluids. Copyright © 2013 Elsevier Inc. All rights reserved.

  10. Polyaniline Coated Core-Shell Typed Stimuli-Responsive Microspheres and Their Electrorheology

    Yu Zhen Dong

    2018-03-01

    Full Text Available Functional core-shell-structured particles have attracted considerable attention recently. This paper reviews the synthetic methods and morphologies of various electro-stimuli responsive polyaniline (PANI-coated core-shell-type microspheres, including PANI-coated Fe3O4, SiO2, Fe2O3, TiO2, poly(methyl methacrylate, poly(glycidyl methacrylate, and polystyrene along with their electrorheological (ER characteristics when prepared by dispersing these particles in an insulating medium. In addition to the various rheological characteristics and their analysis, such as shear stress and yield stress of their ER fluids, this paper summarizes some of the mechanisms proposed for ER fluids to further understand the responses of ER fluids to an externally applied electric field.

  11. Graphene oxide nanocomposites and their electrorheology

    Zhang, Wen Ling; Liu, Ying Dan; Choi, Hyoung Jin

    2013-01-01

    Graphical abstract: - Highlights: • GO-based PANI, NCOPA and PS nanocomposites are prepared. • The nanocomposites are adopted as novel electrorheological (ER) candidates. • Their critical ER characteristics and dielectric performance are analyzed. • Typical ER behavior widens applications of GO-based nanocomposites. - Abstract: Graphene oxide (GO), a novel one-atom carbon system, has become one of the most interesting materials recently due to its unique physical and chemical properties in addition to graphene. This article briefly reviews a recent progress of the fabrication of GO-based polyaniline, ionic N-substituted copolyaniline and polystyrene nanocomposites. The critical electrorheological characteristics such as flow response and yield stress from rheological measurement, relaxation time and achievable polarizability from dielectric analysis are also analyzed

  12. The electrorheological properties of nano-sized SiO2 particle materials doped with rare earths

    Liu Yang; Liao Fuhui; Li Junran; Zhang Shaohua; Chen Shumei; Wei Chenguan; Gao Song

    2006-01-01

    Electrorheological (ER) materials of pure SiO 2 and SiO 2 doped with rare earths (RE = Ce, Gd, Y) (non-metallic glasses (silicates)) were prepared using Na 2 SiO 3 and RECl 3 as starting materials. The electrorheological properties are not enhanced by all rare earth additions. The material doped with Ce exhibits the best ER performance

  13. Electrorheological suspensions of laponite in oil: rheometry studies.

    Parmar, K P S; Méheust, Y; Schjelderupsen, Børge; Fossum, J O

    2008-03-04

    We have studied the effect of an external direct current (DC) electric field ( approximately 1 kV/mm) on the rheological properties of colloidal suspensions consisting of aggregates of laponite particles in a silicone oil. Microscopy observations show that, under application of an electric field greater than a triggering electric field Ec approximately 0.6 kV/mm, laponite aggregates assemble into chain- and/or columnlike structures in the oil. Without an applied electric field, the steady-state shear behavior of such suspensions is Newtonian-like. Under application of an electric field larger than Ec, it changes dramatically as a result of the changes in the microstructure: a significant yield stress is measured, and under continuous shear the fluid is shear-thinning. The rheological properties, in particular the dynamic and static shear stress, were studied as a function of particle volume fraction for various strengths (including null) of the applied electric field. The flow curves at constant shear rate can be scaled with respect to both the particle fraction and electric field strength onto a master curve. This scaling is consistent with simple scaling arguments. The shape of the master curve accounts for the system's complexity; it approaches a standard power-law model at high Mason numbers. Both dynamic and static yield stresses are observed to depend on the particle fraction Phi and electric field E as PhibetaEalpha, with alpha approximately 1.85 and beta approximately 1 and 1.70 for the dynamic and static yield stresses, respectively. The yield stress was also determined as the critical stress at which there occurs a bifurcation in the rheological behavior of suspensions that are submitted to a constant shear stress; a scaling law with alpha approximately 1.84 and beta approximately 1.70 was obtained. The effectiveness of the latter technique confirms that such electrorheological (ER) fluids can be studied in the framework of thixotropic fluids. The method

  14. Spontaneous electrorheological effect in nematic liquid crystals under Taylor-Couette flow configuration

    Dhar, Jayabrata; Chakraborty, Suman

    2017-09-01

    Electrorheological (ER) characteristics of Nematic Liquid Crystals (NLCs) have been a topic of immense interest in the field of soft matter physics owing to its rheological modulation capabilities. Here we explore the augmentation in rheological characteristics of the nematic fluid confined within the annular region of the concentric cylindrical space with an Electrical Double Layer (EDL) induced at the fluid-substrate interface due to certain physico-chemical interactions. Using a Taylor-Couette flow configuration associated with an EDL induced at the inner cylinder wall, we show that a spontaneous electrorheological effect is generated owing to the intrinsic director anisotropy and structural order of complex nematic fluids. We seek to find the enhancement in torque transfer capability due to the inherent electrorheological nature of the nematic medium, apart from exploiting the innate nature of such homogeneous media to remain free of coagulation, a fact which makes it an excellent candidate for the applications in microfluidic environment. Our analysis reveals that with stronger induced charge density within the EDL, the apparent viscosity enhances, which, in turn, augments torque transfer across the concentric cylinder. The velocity profile tends to flatten in comparison to the classical circular Couette flow in annular geometry as one increases the surface charge density. We further observe a more pronounced ER effect for the nematic medium having larger electrical permittivity anisotropy. Besides the torque transfer qualifications, we also explore the distinct scenarios, wherein the same NLC medium exhibits shear thinning and shear thickening characteristics. The present configuration of the efficient torque transfer mechanism may be proficiently downscaled to micro-level and is relevant in the fabrication of micro-clutch and micro-dampers.

  15. An experimental investigation of the dielectric properties of electrorheological fluids

    Sun, Y; Thomas, M; Masounave, J

    2009-01-01

    A home-made electrorheological (ER) fluid, known as ETSERF, has been created with suspension-based powders dispersed in silicone oil. Because of the special structure of their particles, ETSERF suspensions present a complex behavior. In the absence of an electric field, the ETSERF fluid manifests a near-Newtonian behavior, but when an electric field is applied, it exhibits a pseudoplastic behavior with yield stress. The ER effect under DC electric fields has been experimentally investigated using both hydrous and anhydrous ER fluids. The ER properties are strongly dependent on the dielectric properties of ETSERF suspensions, and hydrous ER fluids have a high dielectric constant and a high relaxation frequency which show a strong electrorheological effect. The relationship between the electrorheological effect and the permittivity of ER fluids has also been extensively studied. Experimental results show that the interfacial polarization plays an important role in the electrorheological phenomenon. The ageing of ETSERF fluids was also studied and it was found that the dielectric properties (mainly the dielectric loss tangent) and ER properties are strongly related to the duration of ageing. A fresh ETSERF suspension exhibits high relaxation frequency and high dielectric constant. These results are mainly explained by the effect of interfacial polarizations

  16. Electrorheological fluids and methods

    Green, Peter F.; McIntyre, Ernest C.

    2015-06-02

    Electrorheological fluids and methods include changes in liquid-like materials that can flow like milk and subsequently form solid-like structures under applied electric fields; e.g., about 1 kV/mm. Such fluids can be used in various ways as smart suspensions, including uses in automotive, defense, and civil engineering applications. Electrorheological fluids and methods include one or more polar molecule substituted polyhedral silsesquioxanes (e.g., sulfonated polyhedral silsesquioxanes) and one or more oils (e.g., silicone oil), where the fluid can be subjected to an electric field.

  17. Characterization of the Mechanical Properties of Electrorheological Fluids Made of Starch and Silicone Fluid

    Vieira, Sheila Lopes; de Arruda, Antonio Celso Fonseca

    In the majority of published articles on the topic, ER fluids have been studied as if they were viscous liquids. In this work, electrorheological fluids were characterized as solids and their mechanical properties were determined. The results infer that ER materials are controllably resistant to compression, tensile and shear stress, in this order of magnitude. More precisely, fluids made of starch have elasticity modulus similar to that of rubber, they have tensile strength 103 to 5×104 times lower than that of low density polyethylene (LDPE), static yield stress 4×104 to 8×105 times lower than that of acrylonitrile-butadiene-styrene terpolymer (ABS) and fatigue life similar to some polymers like polyethylene(PE) and polypropylene (PP).

  18. Electrorheology of aniline oligomers

    Mrlík, M.; Sedlačík, M.; Pavlínek, V.; Bober, Patrycja; Trchová, Miroslava; Stejskal, Jaroslav; Sáha, P.

    2013-01-01

    Roč. 291, č. 9 (2013), s. 2079-2086 ISSN 0303-402X R&D Projects: GA ČR GA202/09/1626 Institutional support: RVO:61389013 Keywords : anilin e oligomers * polyaniline * electrorheology Subject RIV: JI - Composite Materials Impact factor: 2.410, year: 2013

  19. Polyaniline in electrorheology

    Quadrat, Otakar; Stejskal, Jaroslav

    2006-01-01

    Roč. 12, č. 3 (2006), s. 352-361 ISSN 1226-086X R&D Projects: GA ČR GA202/06/0419 Institutional research plan: CEZ:AV0Z40500505 Keywords : electrorheology * suspensions of polyaniline * polyaniline derivatives Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.957, year: 2006

  20. Recession in a linear stepper motor based on piezoelectric actuator and electrorheological clampers

    Li, Cuihong; Meng, Yonggang; Tian, Yu

    2012-01-01

    A linear inchworm-type stepper motor based on piezoelectric actuator and comb shape electrorheological (ER) clampers was developed and tested. A recession phenomenon in the movement of the motor was found and was significantly affected by the driving voltage of the piezoelectric actuator and ER fluids. A dynamic model to analyze the mechanism of the recession was established. The force ratio of the viscoelastic clamping force (applied high electric field) to the viscous damping force (zero field) of ER fluids is the critical factor which determines the recession. The ratio is also affected by the extension or contraction rate of the actuator during movement, which is affected by the charging and discharging processes. With a relatively large distance between the clamper electrodes and a small displacement activated by the extension of the piezoelectric actuator, the instantaneous shear rate might not be sufficiently high, preventing ER fluids from attaining a shear-thickened and high-strength state. The ratio of yield strength to the viscous strength of ER fluids during movement should be as large as possible to reduce the recession displacement. (paper)

  1. Tunable 'optical activity' in electrorheological fluids

    Zhao, Q.; Zhao, X.P.

    2005-01-01

    The 'optical activity' of adjustable periodic structure material (SiO 2 and pentaerythrital electrorheological (ER) fluids) is firstly investigated using two kinds of setup. It is found that the rotation angles can be tuned by the external electric field and weight concentrations, and the sign of the rotation angle is negative, so, the used ER fluids are defined as the left-handed optically active substances under the application of electric field. The laser diffraction patterns are also observed in the ER fluids, which indicates the formation of alignment. It is thought that the symmetry breaking of structure induced by applied electric field is the origin of the 'optical activity' in the ER fluids. The electrically tunable 'optical activity' will find innovative applications in displays, optical devices and other fields

  2. Electrorheologic fluids; Fluidos electroreologicos

    Rejon G, Leonardo; Lopez G, Francisco; Montoya T, Gerardo [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Manero B, Octavio [Instituto de Investigaciones en Materiales, UNAM.(Mexico)

    2003-07-01

    The present article has as an objective to offer a review of the research work made in the Instituto de Investigaciones Electricas (IIE) on the study of the electrorheologic fluids whose flow properties can abruptly change in the presence of an electric field when this is induced by a direct current. The electrorheologic fluids have their main application in the manufacture of self-controlling damping systems. [Spanish] El presente articulo tiene por objetivo ofrecer una resena de los trabajos de investigacion realizados en el Instituto de Investigaciones Electricas (IIE) sobre el estudio de los fluidos electroreologicos cuyas propiedades de flujo pueden cambiar abruptamente en presencia de un campo electrico cuando este es inducido por una corriente directa. Los fluidos electroreologicos tienen su principal aplicacion en la fabricacion de sistemas de amortiguamiento autocontrolables.

  3. Electrorheological Properties of Suspensions Prepared from Polystyrene- Block- Polyisoprene Copolymer

    YAVUZ, Mustafa

    2014-01-01

    Considerable scientific and industrial interest is currently being focused on a class of materials known as electrorheological (ER) fluids, which display remarkable rheological behaviour, being able to convert rapidly and repeatedly from a liquid to solid when an electric field (E) is applied or removed. In this article, the synthesis, characterization, partial hydrolysis and ER properties of polystyrene- block}-polyisoprene copolymer (COP) were investigated. The block copolymer was ...

  4. Vibration Control of Sandwich Beams Using Electro-Rheological Fluids

    Srikantha Phani, A.; Venkatraman, K.

    2003-09-01

    Electro-rheological (ER) fluids are a class of smart materials exhibiting significant reversible changes in their rheological and hence mechanical properties under the influence of an applied electric field. Efforts are in progress to embed ER fluids in various structural elements to mitigate vibration problems. The present work is an experimental investigation of the behaviour of a sandwich beam with ER fluid acting as the core material. A starch-silicone-oil-based ER fluid is used in the present study. Significant improvements in the damping properties are achieved in experiments and the damping contributions by viscous and non-viscous forces are estimated by force-state mapping (FSM) technique. With the increase in electric field across the ER fluid from 0 to 2 kV, an increase of 25-50% in equivalent viscous damping is observed. It is observed that as concentration of starch is increased, the ER effect grows stronger but eventually is overcome by applied stresses.

  5. Touch sensitive electrorheological fluid based tactile display

    Liu, Yanju; Davidson, Rob; Taylor, Paul

    2005-12-01

    A tactile display is programmable device whose controlled surface is intended to be investigated by human touch. It has a great number of potential applications in the field of virtual reality and elsewhere. In this research, a 5 × 5 tactile display array including electrorheological (ER) fluid has been developed and investigated. Force responses of the tactile display array have been measured while a probe was moved across the upper surface. The purpose of this was to simulate the action of touch performed by human finger. Experimental results show that the sensed surface information could be controlled effectively by adjusting the voltage activation pattern imposed on the tactels. The performance of the tactile display is durable and repeatable. The touch sensitivity of this ER fluid based tactile display array has also been investigated in this research. The results show that it is possible to sense the touching force normal to the display's surface by monitoring the change of current passing through the ER fluid. These encouraging results are helpful for constructing a new type of tactile display based on ER fluid which can act as both sensor and actuator at the same time.

  6. Electrorheological fluids modeling and mathematical theory

    Růžička, Michael

    2000-01-01

    This is the first book to present a model, based on rational mechanics of electrorheological fluids, that takes into account the complex interactions between the electromagnetic fields and the moving liquid. Several constitutive relations for the Cauchy stress tensor are discussed. The main part of the book is devoted to a mathematical investigation of a model possessing shear-dependent viscosities, proving the existence and uniqueness of weak and strong solutions for the steady and the unsteady case. The PDS systems investigated possess so-called non-standard growth conditions. Existence results for elliptic systems with non-standard growth conditions and with a nontrivial nonlinear r.h.s. and the first ever results for parabolic systems with a non-standard growth conditions are given for the first time. Written for advanced graduate students, as well as for researchers in the field, the discussion of both the modeling and the mathematics is self-contained.

  7. Compressions of electrorheological fluids under different initial gap distances.

    Tian, Yu; Wen, Shizhu; Meng, Yonggang

    2003-05-01

    Compressions of electrorheological (ER) fluids have been carried out under different initial gap distances and different applied voltages. The nominal yield stresses of the compressed ER fluid under different conditions, according to the mechanics of compressing continuous fluids considering the yield stress of the plastic fluid, have been calculated. Curves of nominal yield stress under different applied voltages at an initial gap distance of 4 mm overlapped well and were shown to be proportional to the square of the external electric field and agree well with the traditional description. With the decrease of the initial gap distance, the difference between the nominal yield stress curves increased. The gap distance effect on the compression of ER fluids could not be explained by the traditional description based on the Bingham model and the continuous media theory. An explanation based on the mechanics of particle chain is proposed to describe the gap distance effect on the compression of ER fluids.

  8. Shear bond strength of two bonding systems on dentin surfaces prepared with Er:YAG laser

    Dall'Magro, Eduardo

    2001-01-01

    The purpose of this study was to examine the shear bond strength of two bonding dentin systems, one 'one step' (Single Bond - 3M) and one 'self-etching' (Prompt-L-ESPE), when applied on dentin surfaces prepared with Er:YAG laser (2,94μm) that underwent ar not, acid etched. Forty one human molars just extracted were selected and after the cut with diamond disc and included in acrylic resin, resulting in 81 specimens (hemi crowns). After, the specimens were divided in one group treated with sand paper and another two groups treated with Er:YAG laser with 200 mJ and 250 mJ of energy and 2 Hz of frequency. Next, the prepared surfaces received three treatments with following application: 1) acid + Single Bond + Z 250 resin, 2) prompt-L-Pop + Z 250 resin, and 3) acid without, Single Bond + Z 250 resin. The Z 250 resin was applied and photopolymerized in increments on a Teflon matrix that belonged to an apparatus called 'Assembly Apparatus' machine producing cylinders of 3,5 mm of diameter and 5 mm of height. After these specimens were submitted to thermo cycling during 1 minute the 55 deg C and during 1 minute with 5 deg C with a total of 500 cycles for specimen, and the measures of shear bond strength were abstained using EMIC model DL 2000 rehearsed machine, with speed of 0,5 mm/min, measuring the final rupture tension (Mpa). The results showed an statistic superiority of 5% of probability level in dentin flattened with sandpaper and with laser using 200 mJ of energy with aspect to the ones flattened with laser using 250 mJ of energy. It was observed that using 'Single Bond' bonding dentin system the marks were statistically superior at 5% of probability with reference to the use of the Prompt-L-Pop adhesive system. So, it was concluded that Er:YAG Laser with 200 mJ of energy produced similar dentin cavity prepare than sandpaper and Single Bond seemed the best bonding agent system between restorative material and dentin. (author)

  9. Investigation of electrokinetic and electrorheological properties of polyindole prepared in the presence of a surfactant

    Unal, H. Ibrahim, E-mail: hiunal@gazi.edu.tr [Gazi University, Chemistry Department, Smart Materials Research Lab., Ankara (Turkey); Sahan, Bekir; Erol, Ozlem [Gazi University, Chemistry Department, Smart Materials Research Lab., Ankara (Turkey)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Aggregated morphology was determined for PIN, spherical and porous hollows and everniae form morphologies were recorded for SPIN. Black-Right-Pointing-Pointer The PIN/SO and SPIN/SO systems showed almost similar electrokinetic attitudes and a typical shear thinning non-Newtonian viscoelastic behavior, vibration damping capability at elevated frequencies, and enhanced storage moduli with increasing temperature. Black-Right-Pointing-Pointer Non-linear recoverable viscoelastic manner was revealed from the creep-recovery experiments under external electric field. - Abstract: In this study, synthesis of polyindole (PIN) was carried out without and with the presence of a sodium dodecyl sulfate (SDS) surfactant (SPIN), using FeCl{sub 3} as an oxidizing agent. The synthesized materials were subjected to various characterizations techniques namely: particle size, magnetic susceptibility, elemental analysis, density, conductivity, dielectric constant, FTIR, {sup 1}H NMR, TGA, XRD, and SEM. Characterization results revealed the successful preparation of the homopolymers of PIN and SPIN. Zeta ({zeta})-potentials of the samples were measured in aqueous and non-aqueous (silicone oil, SO) media. Electrokinetic properties of PIN and SPIN in aqueous media were determined by {zeta}-potential measurements in the presence of various electrolytes (NaCl, BaCl{sub 2}, AlCl{sub 3}, Na{sub 2}SO{sub 4}) and surfactants (cetyltrimethyl ammonium bromide, SDS, and Triton X-100). Besides, the effect of pH onto {zeta}-potentials of the materials was also examined. The suspensions prepared in SO were subjected to external electric field strength and their electrorheological (ER) properties were investigated. Then the effects of shear rate, frequency, and temperature onto ER activities of the suspensions were examined. Further, creep and creep-recovery tests were applied to the PIN/SO and SPIN/SO suspension systems and reversible non-linear viscoelastic

  10. Analysis of Shear Bond Strength and Morphology of Er:YAG Laser-Recycled Ceramic Orthodontic Brackets.

    Han, Ruo-qiao; Yang, Kai; Ji, Ling-fei; Ling, Chen

    2016-01-01

    The aim of this study was to compare the recycling of deboned ceramic brackets via an Er:YAG laser or via the traditional chairside processing methods of flaming and sandblasting; shear bond strength and morphological changes were evaluated in recycled brackets versus new brackets. 3M Clarity Self-Ligating Ceramic Brackets with a microcrystalline base were divided into groups subjected to flaming, sandblasting, or exposure to an Er:YAG laser. New ceramic brackets served as a control group. Shear bond strengths were determined with an Electroforce test machine and tested for statistical significance through analysis of variance. Morphological examinations of the recycled ceramic bracket bases were conducted with scanning electron microscopy and confocal laser scanning microscopy. Residue on the bracket base was analyzed with Raman spectroscopy. Faded, dark adhesive was left on recycled bracket bases processed via flaming. Adhesive was thoroughly removed by both sandblasting and exposure to an Er:YAG laser. Compared with new brackets, shear bond strength was lower after sandblasting (p bracket. Er:YAG lasers effectively remove adhesive from the bases of ceramic brackets without damaging them; thus, this method may be preferred over other recycling methods.

  11. PREFACE: 13th International Conference on Electrorheological Fluids and Magnetorheological Suspensions (ERMR2012)

    Unal, Halil Ibrahim

    2013-02-01

    China) gave plenary talks on novel MR shear thickening fluids, MR rubber composites and MR plastomers, respectively. H J Choi (INHA University, Korea), X Zhao (Northwestern Polytechnical University, China) and R Tao (Temple University, USA) delivered plenary lectures on issues relating to the area of electrorheological (ER) fluids. In their talks, Choi and Zhao covered novel ER materials with core-shell structured microspheres and micro/nano hierarchical structured titania particles, respectively, and Tao focused on the reduction of the viscosity of liquid suspensions for energy applications in transporting crude oil via pipelines. Attendance of the presentations was exceptionally high. Poster presentations were divided into two sessions and held in the afternoons after the close of the sessions, which were filled with stimulating discussions. The award for the best student research in the area of electrorheological fluids, sponsored by the Winslow family, was given to Y D Liu of INHA University, Korea on research entitled 'Copolyaniline coated monodisperse polystyrene microparticles and their electrorheological response'. The award for the best student research on magnetorheological suspensions, sponsored by the LORD Corporation, was given to S Kaneko of Keio University, Japan on research entitled 'Effect of a magnetic field on sloshing pressure in a magnetic fluid'. Besides the purely scientific program during the five days, some special events were also organized. A guided tour of the old city and some important landmarks of the capital city of Ankara were organized before the Gala Dinner. Special samples of Turkish classical music and folk dancing were performed by a group from the Republic of Turkey Ministry of Culture and Tourism to exhibit Turkish culture to the delegates at Gala Night, which was truly appreciated. Following the conclusion of this successful meeting, the next conference is expected to be organized at the University of Granada, Spain by Professor

  12. Effect of different provisional cement remnant cleaning procedures including Er:YAG laser on shear bond strength of ceramics

    Zortuk, Mustafa; Gumus, Hasan Onder; Kilinc, Halil Ibrahim; Tuncdemir, Ali Riza

    2012-01-01

    PURPOSE The purpose of this study was to evaluate the effect of provisional cement removal by different dentin cleaning protocols (dental explorer, pumice, cleaning bur, Er:YAG laser) on the shear bond strength between ceramic and dentin. MATERIALS AND METHODS In total, 36 caries-free unrestored human third molars were selected as tooth specimens. Provisional restorations were fabricated and cemented with eugenol-free provisional cement. Then, disc-shaped ceramic specimens were fabricated and...

  13. Basic research of electro-rheological gel drum for novel linear actuator

    Koyanagi, K; Yamaguchi, T; Oshima, T [Toyama Prefectural University, Toyama (Japan); Kakinuma, Y [Keio University, Kanagawa (Japan); Anzai, H; Sakurai, K [Fujikura Kasei, Tochigi (Japan)], E-mail: koyanagi@pu-toyama.ac.jp

    2009-02-01

    In recent years, robots that coexist with human are under active researches. Such robots need high safety, backdriveability, large generative force, high speed response, good controllability, and so on. We have put emphasis on the backdriveability and created a novel prototype linear actuator with an ER (Electro-Rheological) gel, a new functional material. It is an all-purpose actuator satisfying characteristics for human-coexistence welfare robot.

  14. Electrorheological Properties of Suspensions Prepared from Poly(Li-tert-butyl methacrylate) Ionomer

    YAVUZ, Mustafa

    2014-01-01

    The synthesis, characterisation and partial hydrolysis of poly(tert-butylmethacrylate), (PTBMA), and the electrorheological (ER) properties of its suspensions were investigated. The polymer was synthesised by radical polymerisation and partially hydrolysed by para-toluenesulphonic acid monohydrate (PTSA.H2O), and then converted to a lithium salt (PTBMA-Li) by washing with a LiOH(aq) solution. From particle size measurements, the average particle size of PTBMA-Li was determined to be ...

  15. Electro-capillary effects in capillary filling dynamics of electrorheological fluids.

    Dhar, Jayabrata; Ghosh, Uddipta; Chakraborty, Suman

    2015-09-21

    The flow of electrorheological fluids is characterized by an apparent increase in viscosity manifested by the yield stress property of the fluid, which is a function of the applied electric field and the concentration of the suspended solute phase within the dielectric medium. This property of electrorheological fluids generally hinders flow through a capillary if the imposed shear stress is lower than the induced yield stress. This results in a plug-like zone in the flow profile, thus giving the fluid Bingham plastic properties. In the present work, we study such influences of the yield stress on the capillary filling dynamics of an electrorheological fluid by employing a rheologically consistent reduced order formalism. One important feature of the theoretical formalism is its ability to address the intricate interplay between the surface tension and viscous forces, both of which depend sensitively on the electric field. Our analysis reveals that the progress of the capillary front is hindered at an intermediate temporal regime, which is attributable to the increase of the span of the plug-zone across the channel width with time. With a preliminary understanding on the cessation of the capillary front advancement due to the yield stress property of the electrorheological fluids, we further strive to achieve a basic comparison with an experimental study made earlier. Reasonable agreements with the reported data support our theoretical framework. Comprehensive scaling analysis brings further insight to our reported observations over various temporal regimes.

  16. Synthesis of flower-like BaTiO3/Fe3O4 hierarchically structured particles and their electrorheological and magnetic properties.

    Wang, Baoxiang; Yin, Yichao; Liu, Chenjie; Yu, Shoushan; Chen, Kezheng

    2013-07-21

    Flower-like BaTiO3/Fe3O4 hierarchically structured particles composed of nano-scale structures on micro-scale materials were synthesized by a simple solvothermal approach and characterized by the means of X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), magnetic testing and rotary viscometer. The influences on the morphology and structure of solvothermal times, type and amount of surfactant, EG : H2O ratio, etc. were studied. Magnetic testing results show that the samples have strong magnetism and they exhibit superparamagnetic behavior, as evidenced by no coercivity and the remanence at room temperature, due to their very small sizes, observed on the M-H loop. The saturation magnetization (M(s)) value can achieve 18.3 emu g(-1). The electrorheological (ER) effect was investigated using a suspension of the flower-like BaTiO3/Fe3O4 hierarchically structured particles dispersed in silicone oil. We can observe a slight shear-thinning behavior of shear viscosity at a low shear rate region even at zero applied electric field and a Newtonian fluid behavior at high shear rate regions.

  17. Effects of confinement & surface roughness in electrorheological flows

    Helal, Ahmed; Telleria, Maria J.; Wang, Julie; Strauss, Marc; Murphy, Mike; McKinley, Gareth; Hosoi, A. E.

    2014-11-01

    Electrorheological (ER) fluids are dielectric suspensions that exhibit a fast, reversible change in rheological properties with the application of an external electric field. Upon the application of the electric field, the material develops a field-dependent yield stress that is typically modeled using a Bingham plastic model. ER fluids are promising for designing small, cheap and rapidly actuated hydraulic devices such as rapidly-switchable valves, where fluid flowing in a microchannel can be arrested by applying an external electric field. In the lubrication limit, for a Bingham plastic fluid, the maximum pressure the channel can hold, before yielding, is a function of the field-dependent yield stress, the length of the channel and the electrode gap. In practice, the finite width of the channel and the surface roughness of the electrodes could affect the maximum yield pressure but a quantitative understanding of these effects is currently lacking. In this study, we experimentally investigate the effects of the channel aspect ratio (width/height) and the effects of electrode roughness on the performance of ER valves. Based on this quantitative analysis, we formulate new performance metrics for ER valves as well as design rules for ER valves that will help guide and optimize future designs.

  18. Dynamic simulation of an electrorheological fluid

    Bonnecaze, R.T.; Brady, J.F.

    1992-01-01

    A molecular-dynamics-like method is presented for the simulation of a suspension of dielectric particles in a nonconductive solvent forming an electrorheological fluid. The method accurately accounts for both hydrodynamic and electrostatic interparticle interactions from dilute volume fractions to closest packing for simultaneous shear and electric fields. The hydrodynamic interactions and rheology are determined with the Stokesian dynamics methodology, while the electrostatic interactions, in particular, the conservative electrostatic interparticle forces, are determined from the electrostatic energy of the suspension. The energy of the suspension is computed from the induced particle dipoles by a method previously developed [R. T. Bonnecaze and J. F. Brady, Proc. R. Soc. London, Ser. A 430, 285 (1990)]. Using the simulation, the dynamics can be directly correlated to the observed macroscopic rheology of the suspension for a range of the so-called Mason number, Ma, the ratio of viscous to electrostatic forces. The simulation is specifically applied to a monolayer of spherical particles of areal fraction 0.4 with a particle-to-fluid dielectric constant ratio of 4 for Ma=10 -4 to ∞. The effective viscosity of the suspension increases as Ma -1 or with the square of the electric field for small Ma and has a plateau value at large Ma, as is observed experimentally. This rheological behavior can be interpreted as Bingham plastic-like with a dynamic yield stress. The first normal stress difference is negative, and its magnitude increases as Ma -1 at small Ma with a large Ma plateau value of zero. In addition to the time averages of the rheology, the time traces of the viscosities are presented along with selected ''snapshots'' of the suspension microstructure

  19. Shear bond strength of resin composite bonded with two adhesives: Influence of Er: YAG laser irradiation distance

    Shirani, Farzaneh; Birang, Reza; Malekipour, Mohammad Reza; Hourmehr, Zahra; Kazemi, Shantia

    2014-01-01

    Background: Dental surfaces prepared with different Er:YAG laser distance may have different characteristics compared with those prepared with conventional instruments. The aim of this study was to investigate the effect of Er:YAG laser irradiation distance from enamel and dentin surfaces on the shear bond strength of composite with self-etch and etch and rinse bonding systems compared with conventional preparation method. Materials and Methods: Two hundred caries-free human third molars were randomly divided into twenty groups (n = 10). Ten groups were designated for enamel surface (E1-E10) and ten for dentin surface (D1-D10). Er: YAG laser (2940 nm) was used on the E1-E8 (240 mJ, 25 Hz) and D1-D8 (140 mJ, 30 Hz) groups at four different distances of 0.5 (standard), 2, 4 and 11 mm. Control groups (E9, E10, D9 and D10) were ground with medium grit diamond bur. The enamel and dentin specimens were divided into two subgroups that were bonded with either Single Bond or Clearfil SE Bond. Resin composite (Z100) was dispensed on prepared dentin and enamel. The shear bond strengths were tested using a universal testing machine. Data were analyzed by SPSS12 statistical software using three way analysis of variance, Tukey and independent t-test. P enamel and dentin substrates (P enamel surfaces (in both bonding agent subgroups) and on dentin surfaces (in the Single Bond subgroup). Conclusion: Laser irradiation decreases shear bond strength. Irradiation distance affects shear bond strength and increasing the distance would decrease the negative effects of laser irradiation. PMID:25540665

  20. Effect of different provisional cement remnant cleaning procedures including Er:YAG laser on shear bond strength of ceramics.

    Zortuk, Mustafa; Gumus, Hasan Onder; Kilinc, Halil Ibrahim; Tuncdemir, Ali Riza

    2012-11-01

    The purpose of this study was to evaluate the effect of provisional cement removal by different dentin cleaning protocols (dental explorer, pumice, cleaning bur, Er:YAG laser) on the shear bond strength between ceramic and dentin. In total, 36 caries-free unrestored human third molars were selected as tooth specimens. Provisional restorations were fabricated and cemented with eugenol-free provisional cement. Then, disc-shaped ceramic specimens were fabricated and randomly assigned to four groups of dentin cleaning protocols (n = 9). Group 1 (control): Provisional cements were mechanically removed with a dental explorer. Group 2: The dentin surfaces were treated with a cleaning brush with pumice Group 3: The dentin surfaces were treated with a cleaning bur. Group 4: The provisional cements were removed by an Er:YAG laser. Self-adhesive luting cement was used to bond ceramic discs to dentin surfaces. Shear bond strength (SBS) was measured using a universal testing machine at a 0.05 mm/min crosshead speed. The data were analyzed using a Kolmogorov Smirnov, One-way ANOVA and Tukey HSD tests to perform multiple comparisons (α=0.05). THE DENTIN CLEANING METHODS DID NOT SIGNIFICANTLY AFFECT THE SBS OF CERAMIC DISCS TO DENTIN AS FOLLOWS: dental explorer, pumice, cleaning bur, and Er:YAG laser. The use of different cleaning protocols did not affect the SBS between dentin and ceramic surfaces.

  1. Reduced transport and ER shearing in improved confinement regimes in JT-60U

    Shirai, H.; Kikuchi, M.; Takizuka, T.

    2001-01-01

    The global confinement and the local transport properties of improved core confinement plasmas in JT-60U have been studied in connection with E r shear formation. The improved core confinement mode with ITB, the internal transport barrier, is roughly classified into 'parabolic' type ITBs and 'box' type ITBs. The parabolic type ITB has the reduced thermal diffusivity, χ, in the core region; however, the E r shear, dE r /dr, is not so strong. The box type ITB has a very strong E r shear at the thin ITB layer and the χ value decreases to the level of neoclassical transport there. The estimated ExB shearing rate, ω ExB , becomes almost the same as the linear growth rate of the drift microinstability, γ L , at the ITB layer in the box type ITB. Experiments of hot ion mode plasmas during the repetitive L-H-L transition shows that the thermal diffusivity clearly depends on the E r shear and the strong E r shear contributes to the reduced thermal diffusivity. (author)

  2. Reduced transport and Er shearing in improved confinement regimes in JT-60U

    Shirai, H.; Kikuchi, M.; Takizuka, T.

    1999-01-01

    The global confinement and the local transport properties of improved core confinement plasmas in JT-60U were studied in connection with E r shear formation. In the improved core confinement mode with internal transport barriers (ITBs), these are roughly classified into 'parabolic type' ITBs and 'box type' ITBs. The parabolic type ITB has a reduced thermal diffusivity χ in the core region; however, the E r shear, dE r /dr, is not as strong. The box type ITB has a very strong E r shear at the thin ITB layer and χ decreases to the level of neoclassical transport there. The estimated E x B shearing rate, ω ExB , becomes almost the same as the linear growth rate of the drift microinstability, γ L , at the ITB layer in the box type ITB. Experiments with hot ion mode plasmas during the repetitive L-H-L transition showed that the thermal diffusivity clearly depends on the E r shear and the strong E r shear contributes to the reduced thermal diffusivity. (author)

  3. Shear bond strength of composite bonded with three adhesives to Er,Cr:YSGG laser-prepared enamel.

    Türkmen, Cafer; Sazak-Oveçoğlu, Hesna; Günday, Mahir; Güngör, Gülşad; Durkan, Meral; Oksüz, Mustafa

    2010-06-01

    To assess in vitro the shear bond strength of a nanohybrid composite resin bonded with three adhesive systems to enamel surfaces prepared with acid and Er,Cr:YSGG laser etching. Sixty extracted caries- and restoration-free human maxillary central incisors were used. The teeth were sectioned 2 mm below the cementoenamel junction. The crowns were embedded in autopolymerizing acrylic resin with the labial surfaces facing up. The labial surfaces were prepared with 0.5-mm reduction to receive composite veneers. Thirty specimens were etched with Er,Cr:YSGG laser. This group was also divided into three subgroups, and the following three bonding systems were then applied on the laser groups and the other three unlased groups: (1) 37% phosphoric acid etch + Bond 1 primer/adhesive (Pentron); (2) Nano-bond self-etch primer (Pentron) + Nano-bond adhesive (Pentron); and (3) all-in-one adhesive-single dose (Futurabond NR, Voco). All of the groups were restored with a nanohybrid composite resin (Smile, Pentron). Shear bond strength was measured with a Zwick universal test device with a knife-edge loading head. The data were analyzed with two-factor ANOVA. There were no significant differences in shear bond strength between self-etch primer + adhesive and all-in-one adhesive systems for nonetched and laser-etched enamel groups (P > .05). However, bond strength values for the laser-etched + Bond 1 primer/adhesive group (48.00 +/- 13.86 MPa) were significantly higher than the 37% phosphoric acid + Bond 1 primer/adhesive group (38.95 +/- 20.07 MPa) (P enamel surface more effectively than 37% phosphoric acid for subsequent attachment of composite material.

  4. A comparative study of shear bond strength of orthodontic bracket after acid-etched and Er:YAG treatment on enamel surface

    Leão, Juliana C.; Mota, Cláudia C. B. O.; Cassimiro-silva, Patricia F.; Gomes, Anderson S. L.

    2016-02-01

    This study aimed to evaluate the shear bond strength (SBS) of teeth prepared for orthodontic bracket bonding with 37% phosphoric acid and Er:YAG laser. Forty bovine incisors were divided into two groups. In Group I, the teeth were conditioned with 37% phosphoric acid and brackets were bonded with Transbond XT; in Group II, the teeth were irradiated with Er:YAG and bonding with Transbond XT. After SBS test, the adhesive remnant index was determined. Adhesion to dental hard tissues after Er:YAG laser etching was inferior to that obtained after acid etching but exceeded what is believed to be clinically sufficient strength, and therefore can be used in patients.

  5. Manipulation of microfluidic droplets by electrorheological fluid

    Zhang, Menying

    2009-09-01

    Microfluidics, especially droplet microfluidics, attracts more and more researchers from diverse fields, because it requires fewer materials and less time, produces less waste and has the potential of highly integrated and computer-controlled reaction processes for chemistry and biology. Electrorheological fluid, especially giant electrorheological fluid (GERF), which is considered as a kind of smart material, has been applied to the microfluidic systems to achieve active and precise control of fluid by electrical signal. In this review article, we will introduce recent results of microfluidic droplet manipulation, GERF and some pertinent achievements by introducing GERF into microfluidic system: digital generation, manipulation of "smart droplets" and droplet manipulation by GERF. Once it is combined with real-time detection, integrated chip with multiple functions can be realized. © 2009 Wiley-VCH Verlag GmbH & Co. KGaA.

  6. Shear bond strength and SEM morphology evaluation of different dental adhesives to enamel prepared with ER:YAG laser.

    Pires, Patrícia T; Ferreira, João C; Oliveira, Sofia A; Azevedo, Alvaro F; Dias, Walter R; Melo, Paulo R

    2013-01-01

    Early observations of enamel surfaces prepared by erbium lasers motivated clinicians to use laser as an alternative to chemical etching. Evaluate shear bond strength (SBS) values of different dental adhesives on Erbium:Yttrium Aluminum Garnet (Er:YAG) laser prepared enamel and to evaluate possible etching patterns correlations between dental adhesives and SBS values. One hundred bovine incisors were randomly assigned to SBS tests on enamel (n = 15) and to enamel morphology analysis (n = 5) after Er:YAG laser preparation as follows: Group I - 37% phosphoric acid (PA)+ ExciTE(®); Group II - ExciTE(®); Group III - AdheSE(®) self-etching; Group IV - FuturaBond(®) no-rinse. NR; Group V - Xeno(®) V. Teeth were treated with the adhesive systems and subjected to thermal cycling. SBS were performed in a universal testing machine at 5 mm/min. One-way ANOVA and post-hoc tests (P adhesive systems yielded significantly different SBSs. Acid etching significantly increased the adhesion in laser treated enamel. No differences in SBS values were obtained between AdheSE(®) and ExciTE(®) without condition with PA. FuturaBond(®) NR and Xeno(®) V showed similar SBS, which was lower in comparison to the others adhesives. No correlation between enamel surface morphology and SBS values was observed, except when PA was used.

  7. Electrorheological (ER) fluids: A research needs assessment. Final report

    Krieger, I.M.; Collins, E.A. [Consultec Scientific, Inc., Knoxville, TN (United States)

    1993-05-01

    This report consists of seven sections: (1) Executive Summary, (2) Introduction, (3) Overview, (4) Recommendations, (5) Panelist Reports, (6) Overseas Research and Development, and (7) Extended Bibliography. The Appendix contains the reports of site visits and contacts and other supplementary documents.

  8. Characteristics of an electro-rheological fluid valve used in an inkjet printhead

    Lee, C. Y.; Liao, W. C.

    2000-12-01

    The demand for non-impact printers has grown considerably with the advent of personal computers. For entry-level mass production, two drop-on-demand techniques have dominated the market - piezoelectric impulse and thermal-bubble types. However, the high cost of the piezoelectric printhead and the thermal problems encountered by the thermal-bubble jet printhead have restrained the use of these techniques in an array-type printhead. In this study, we propose a new design of printhead with an electro-rheological (ER) fluid acting as a control medium. The ER fluid valve controls the ink ejection. As a first step toward developing this new printhead, the characteristics of an ER fluid valve which controls the deflection of the elastic diaphragm are investigated. First, the response of a prototype is tested experimentally to prove the feasibility of using this ER valve for the inkjet printhead. Then, the discretized governing equation of the ER valve is derived. Finally, the prototype of the ER valve is fabricated. The experimental measurement based on the sinusoidal response verifies both the theoretical analysis and the controllability of the response of the ER valve by the applied electric field.

  9. Comparison of Shear Bond Strength of Orthodontic Brackets Bonded to Enamel Prepared By Er:YAG Laser and Conventional Acid-Etching

    Hosseini, M.H.; Namvar, F.; Chalipa, J.; Saber, K.; Chiniforush, N.; Sarmadi, S.; Mirhashemi, A.H.

    2012-01-01

    Introduction: The purpose of this study was to compare shear bond strength (SBS) of orthodontic brackets bonded to enamel prepared by Er:YAG laser with two different powers and conventional acid-etching. Materials and Methods: Forty-five human premolars extracted for orthodontic purposes were randomly assigned to three groups based on conditioning method: Group 1- conventional etching with 37% phosphoric acid; Group 2- irradiation with Er:YAG laser at 1 W; and Group 3- irradiation with Er:YAG laser at 1.5 W. Metal brackets were bonded on prepared enamel using a light-cured composite. All groups were subjected to thermocycling process. Then, the specimens mounted in auto-cure acryle and shear bond strength were measured using a universal testing machine with a crosshead speed of 0.5 mm per second. After debonding, the amount of resin remaining on the teeth was determined using the adhesive remnant index (ARI) scored 1 to 5. One-way analysis of variance was used to compare shear bond strengths and the Kruskal-Wallis test was performed to evaluate differences in the ARI for different etching types. Results: The mean and standard deviation of conventional acid-etch group, 1W laser group and 1.5W laser group was 3.82 ± 1.16, 6.97 ± 3.64 and 6.93 ± 4.87, respectively. Conclusion: The mean SBS obtained with an Er:YAG laser operated at 1W or 1.5W is approximately similar to that of conventional etching. However, the high variability of values in bond strength of irradiated enamel should be considered to find the appropriate parameters for applying Er:YAG laser as a favorable alternative for surface conditioning. PMID:22924098

  10. Comparison of Shear Bond Strength of Orthodontic Brackets Bonded to Enamel Prepared By Er:YAG Laser and Conven-tional Acid-Etching

    M.H. Hosseini

    2012-01-01

    Full Text Available Introduction: The purpose of this study was to compare shear bond strength (SBS of orthodontic brackets bonded to enamel prepared by Er:YAG laser with two different powers and conventional acid-etching.Materials and Methods: Forty-five human premolars extracted for orthodontic purposes were randomly assigned to three groups based on conditioning method: Group 1- conventional etching with 37% phosphoric acid; Group 2- irradiation with Er:YAG laser at 1 W; and Group 3- irradiation with Er:YAG laser at 1.5 W. Metal brackets were bonded on prepared enamel using a light-cured composite. All groups were subjected to thermocycling process. Then, the specimens mounted in auto-cure acryle and shear bond strength were measured using a universal testing machine with a crosshead speed of 0.5 mm per second. After debonding, the amount of resin remaining on the teeth was determined using the adhesive remnant index (ARI scored 1 to 5. One-way analysis of variance was used to compare shear bond strengths and the Kruskal-Wallis test was performed to evaluate differences in the ARI for different etching types.Results: The mean and standard deviation of conventional acid-etch group, 1W laser group and 1.5W laser group was 3.82 ± 1.16, 6.97 ± 3.64 and 6.93 ± 4.87, respectively.Conclusion: The mean SBS obtained with an Er:YAG laser operated at 1W or 1.5W is approximately similar to that of conventional etching. However, the high variability of values in bond strength of irradiated enamel should be considered to find the appropriate parameters for applying Er:YAG laser as a favorable alternative for surface conditioning.

  11. Shear bond strength and SEM morphology evaluation of different dental adhesives to enamel prepared with ER:YAG laser

    Patrícia T Pires

    2013-01-01

    Full Text Available Context: Early observations of enamel surfaces prepared by erbium lasers motivated clinicians to use laser as an alternative to chemical etching. Aims: Evaluate shear bond strength (SBS values of different dental adhesives on Erbium:Yttrium Aluminum Garnet (Er:YAG laser prepared enamel and to evaluate possible etching patterns correlations between dental adhesives and SBS values. Subjects and Methods: One hundred bovine incisors were randomly assigned to SBS tests on enamel (n = 15 and to enamel morphology analysis ( n = 5 after Er:YAG laser preparation as follows: Group I - 37% phosphoric acid (PA+ ExciTE® ; Group II - ExciTE® ; Group III - AdheSE® self-etching; Group IV - FuturaBond® no-rinse. NR; Group V - Xeno® V. Teeth were treated with the adhesive systems and subjected to thermal cycling. SBS were performed in a universal testing machine at 5 mm/min. Statistical Analysis Used: One-way ANOVA and post-hoc tests (p < 0.05. For the morphology evaluation, specimens were immersed in Ethylenediamine tetraacetic acid (EDTA and the etching pattern analyzed under Scanning Electron Microscope (SEM. Results: Mean bond strengths were Group I - 47.17 ± 1.61 MPa (type I etching pattern; Group II - 32.56 ± 1.64 MPa, Group III - 29.10 ± 1.34 MPa, Group IV - 23.32 ± 1.53 MPa (type III etching pattern; Group V - 24.43 MPa ± 1.55 (type II etching pattern. Conclusions: Different adhesive systems yielded significantly different SBSs. Acid etching significantly increased the adhesion in laser treated enamel. No differences in SBS values were obtained between AdheSE® and ExciTE® without condition with PA. FuturaBond® NR and Xeno® V showed similar SBS, which was lower in comparison to the others adhesives. No correlation between enamel surface morphology and SBS values was observed, except when PA was used.

  12. Characterisation of electrorheological liquids based on suspensions; Charakterisierung von elektrorheologischen Fluessigkeiten auf Basis von Suspensionen

    Johnston, Lucien [FLUDICON GmbH, Darmstadt (Germany); Schneider, Steffen; Schneider, Ines [Wehrwissenschaftliches Institut fuer Werk-, Explosiv- und Betriebsstoffe (WIWEB), Erding (Germany)

    2008-08-15

    Electrorheological fluids (ERF) belong to the group of 'Smart Materials'. These suspensions have the favourable property of changing their viscosity in an electrical field. This change is spontaneous (response time under 1 ms), continuously variable (from a thin fluid to a semi-solid state), reversible and can be repeated as often as desired. ER-fluids also have certain sensory properties. The sum of these properties allows for the design of mechanical valves which have no moving components. Instead of adjusting the cross-sectional area of a valve orifice, variations in pressure drop over the valve are realised by altering the viscosity of the fluid itself. The simplicity and effectiveness of the ER-effect has lead to a diverse range of applications which make use of this property - from continuously variable hydraulic shock absorbers to highly dynamic actuators. Since the discovery of the ER-effect in the 1904s, many ER-fluids have been developed and tested. This article will discuss the properties and composition of an industrially successful ER-suspension as well as highlighting its implementation in a diverse range of engineering applications. (orig.)

  13. Torque Measurement of 3-DOF Haptic Master Operated by Controllable Electrorheological Fluid

    Oh Jong-Seok

    2015-02-01

    Full Text Available This work presents a torque measurement method of 3-degree-of-freedom (3-DOF haptic master featuring controllable electrorheological (ER fluid. In order to reflect the sense of an organ for a surgeon, the ER haptic master which can generate the repulsive torque of an organ is utilized as a remote controller for a surgery robot. Since accurate representation of organ feeling is essential for the success of the robot-assisted surgery, it is indispensable to develop a proper torque measurement method of 3-DOF ER haptic master. After describing the structural configuration of the haptic master, the torque models of ER spherical joint are mathematically derived based on the Bingham model of ER fluid. A new type of haptic device which has pitching, rolling, and yawing motions is then designed and manufactured using a spherical joint mechanism. Subsequently, the field-dependent parameters of the Bingham model are identified and generating repulsive torque according to applied electric field is measured. In addition, in order to verify the effectiveness of the proposed torque model, a comparative work between simulated and measured torques is undertaken.

  14. One-pot synthesis of polyaniline-doped in mesoporous TiO2 and its electrorheological behavior

    Wei Chuan; Zhu Yihua; Yang Xiaoling; Li Chunzhong

    2007-01-01

    A class of hybrid organic-inorganic composite for application in electrorheological (ER) fluid was prepared by using a simple one-pot method. Transmission electron microscopy (TEM) image shows that the synthesized material had a mesoporous structure. X-ray diffraction (XRD) further proves that the pore size is about 7.4 nm with an anatase TiO 2 framework. Fourier transform infrared (FT-IR) and nitrogen sorption curve reveal polyaniline (PANI) is doped in mesochannels. The ER behaviors of PANI/TiO 2 in silicone oil are invesigated with different doping degrees under different electric fields. The results obtained provide more insight into the role of proper doping in ER fluid

  15. Volume-constrained optimization of magnetorheological and electrorheological valves and dampers

    Rosenfeld, Nicholas C.; Wereley, Norman M.

    2004-12-01

    This paper presents a case study of magnetorheological (MR) and electrorheological (ER) valve design within a constrained cylindrical volume. The primary purpose of this study is to establish general design guidelines for volume-constrained MR valves. Additionally, this study compares the performance of volume-constrained MR valves against similarly constrained ER valves. Starting from basic design guidelines for an MR valve, a method for constructing candidate volume-constrained valve geometries is presented. A magnetic FEM program is then used to evaluate the magnetic properties of the candidate valves. An optimized MR valve is chosen by evaluating non-dimensional parameters describing the candidate valves' damping performance. A derivation of the non-dimensional damping coefficient for valves with both active and passive volumes is presented to allow comparison of valves with differing proportions of active and passive volumes. The performance of the optimized MR valve is then compared to that of a geometrically similar ER valve using both analytical and numerical techniques. An analytical equation relating the damping performances of geometrically similar MR and ER valves in as a function of fluid yield stresses and relative active fluid volume, and numerical calculations are provided to calculate each valve's damping performance and to validate the analytical calculations.

  16. Fabrication of poly(o-anisidine) coated silica core-shell microspheres and their electrorheological response

    Lee, Chul Joo; Choi, Hyoung Jin

    2017-11-01

    In this work, silica/poly(o-anisidine) (POA) core-shell structured microspheres were synthesized by coating the silica core surface with POA with a help of a chemical grafting agent, N-[(3-trimethoxylsilyl)-propyl] aniline. The synthesized silica microspheres were then applied as a polymer/inorganic composite particle-based electrorheological (ER) fluid. The morphology of the silica/POA microspheres was examined by using both transmission electron microscopy and scanning electron microscopy, while their thermal properties and chemical structure were checked by thermogravimetric analysis and Fourier-transform infrared spectroscopy, respectively. The ER properties of the silica/POA particle-based ER fluid were examined by using a Couette-type rotational rheometer equipped with a high-voltage power supplier and analyzed by the Bingham model and modified Mason number. In order to obtain additional information about the electrical polarization properties, the dielectric spectra were measured by an LCR meter and fitted by using the Cole-Cole equation. Furthermore, suspension stability of the ER fluid was tested using Turbiscan.

  17. Electrorheology leads to healthier and tastier chocolate.

    Tao, Rongjia; Tang, Hong; Tawhid-Al-Islam, Kazi; Du, Enpeng; Kim, Jeongyoo

    2016-07-05

    Chocolate is one of the most popular food types and flavors in the world. Unfortunately, at present, chocolate products contain too much fat, leading to obesity. Although this issue was called into attention decades ago, no actual solution was found. To bypass this critical outstanding problem, two manufacturers introduced some low-calorie fats to substitute for cocoa butter. Somehow, their products are not allowed in most countries. Here we show that this issue is deeply related to the basic science of soft matter, especially to the viscosity of liquid suspension and maximally random jammed (MRJ) density. When the concentration of cocoa solid is high, close to the MRJ density, removing a small amount of fat will jam the chocolate flow. Applying unconventional electrorheology to liquid chocolate with applied field in the flow direction, we aggregate the cocoa particles into prolate spheroids in micrometers. This microstructure change breaks the rotational symmetry, reduces liquid chocolate's viscosity along the flow direction, and increases its MRJ density significantly. Hence the fat level in chocolate can be effectively reduced. We are expecting a new class of healthier and tastier chocolate soon.

  18. Electrorheology leads to healthier and tastier chocolate

    Tao, Rongjia; Tang, Hong; Tawhid-Al-Islam, Kazi; Du, Enpeng; Kim, Jeongyoo

    2016-01-01

    Chocolate is one of the most popular food types and flavors in the world. Unfortunately, at present, chocolate products contain too much fat, leading to obesity. Although this issue was called into attention decades ago, no actual solution was found. To bypass this critical outstanding problem, two manufacturers introduced some low-calorie fats to substitute for cocoa butter. Somehow, their products are not allowed in most countries. Here we show that this issue is deeply related to the basic science of soft matter, especially to the viscosity of liquid suspension and maximally random jammed (MRJ) density. When the concentration of cocoa solid is high, close to the MRJ density, removing a small amount of fat will jam the chocolate flow. Applying unconventional electrorheology to liquid chocolate with applied field in the flow direction, we aggregate the cocoa particles into prolate spheroids in micrometers. This microstructure change breaks the rotational symmetry, reduces liquid chocolate’s viscosity along the flow direction, and increases its MRJ density significantly. Hence the fat level in chocolate can be effectively reduced. We are expecting a new class of healthier and tastier chocolate soon. PMID:27325758

  19. Development of high-performance ER gel produced by electric-field assisted molding

    Kakinuma, Y; Aoyama, T; Anzai, H

    2009-01-01

    Electro-rheological gel (ERG) is a novel functional elastomer whose surface frictional and adhesive property varies according to the intensity of applied electric field. This peculiar phenomenon is named as Electro-adhesive effect. A generated shear stress of ERG under applied electric field is approximately 30∼40 times higher than that of ERF because of high adhesive strength. However, the performances of ERG vary widely due to its surface condition, especially density and distribution of ER particles at the surface. In order to stabilize and improve the performance of ERG, the electric- filed assisted molding process is proposed as the producing method of ERG. In this study, first, the principle of electro-adhesive effect is theoretically investigated. Second, a high-performance ERG produced by the proposed process, in which ER particles are aligned densely at the surface, is developed and its performance is evaluated experimentally. As the experimental result, the high-performance ERG shows twice higher shear stress than the conventional ERG.

  20. Development of high-performance ER gel produced by electric-field assisted molding

    Kakinuma, Y; Aoyama, T [Department of System Design Engineering, Keio University, 3-14-1 Hiyoshi Kouhoku-ku Yokohama (Japan); Anzai, H [Fujikura kasei Co., Ltd. 2-6-15 Shibakouen, Minato-ku, Tokyo (Japan)], E-mail: kakinuma@sd.keio.ac.jp

    2009-02-01

    Electro-rheological gel (ERG) is a novel functional elastomer whose surface frictional and adhesive property varies according to the intensity of applied electric field. This peculiar phenomenon is named as Electro-adhesive effect. A generated shear stress of ERG under applied electric field is approximately 30{approx}40 times higher than that of ERF because of high adhesive strength. However, the performances of ERG vary widely due to its surface condition, especially density and distribution of ER particles at the surface. In order to stabilize and improve the performance of ERG, the electric- filed assisted molding process is proposed as the producing method of ERG. In this study, first, the principle of electro-adhesive effect is theoretically investigated. Second, a high-performance ERG produced by the proposed process, in which ER particles are aligned densely at the surface, is developed and its performance is evaluated experimentally. As the experimental result, the high-performance ERG shows twice higher shear stress than the conventional ERG.

  1. Electrorheological properties of suspensions of polypyrrole coated titanate nanorods

    Mrlík, M.; Pavlínek, V.; Saha, P.; Quadrat, Otakar

    2011-01-01

    Roč. 21, č. 5 (2011), 52365_1-52365_7 ISSN 1430-6395 R&D Projects: GA ČR GA202/09/1626 Institutional research plan: CEZ:AV0Z40500505 Keywords : polypyrrole * nanorods * electrorheology Subject RIV: BK - Fluid Dynamics Impact factor: 1.000, year: 2011

  2. Design and dynamic modeling of electrorheological fluid-based variable-stiffness fin for robotic fish

    Bazaz Behbahani, Sanaz; Tan, Xiaobo

    2017-08-01

    Fish actively control their stiffness in different swimming conditions. Inspired by such an adaptive behavior, in this paper we study the design, prototyping, and dynamic modeling of compact, tunable-stiffness fins for robotic fish, where electrorheological (ER) fluid serves as the enabling element. A multi-layer composite fin with an ER fluid core is prototyped and utilized to investigate the influence of electrical field on its performance. Hamilton's principle is used to derive the dynamic equations of motion of the flexible fin, and Lighthill's large-amplitude elongated-body theory is adopted to estimate the hydrodynamic force when the fin undergoes base-actuated rotation. The dynamic equations are then discretized using the finite element method, to obtain an approximate numerical solution. Experiments are conducted on the prototyped flexible ER fluid-filled beam for parameter identification and validation of the proposed model, and for examining the effectiveness of electrically controlled stiffness tuning. In particular, it is found that the natural frequency is increased by almost 40% when the applied electric field changes from 0 to 1.5× {10}6 {{V}} {{{m}}}-1.

  3. Sub-ablative Er,Cr:YSGG laser irradiation under all-ceramic restorations: effects on demineralization and shear bond strength.

    Bağlar, Serdar

    2018-01-01

    This study evaluated the caries resistant effects of sub-ablative Er,Cr:YSGG laser irradiation alone and combined with fluoride in comparison with fluoride application alone on enamel prepared for veneer restorations. And also, evaluated these treatments' effects on the shear bond strength of all-ceramic veneer restorations. One hundred and thirty-five human maxillary central teeth were assigned to groups of 1a-control, 1b-laser treated, 1c-fluoride treated, 1d-laser + fluoride treated for shear bond testing and to groups of 2a-positive control(non-demineralised), 2b-laser treated, 2c-fluoride treated, 2d-laser + fluoride treated, 2e-negative control (demineralised) for microhardness testing (n = 15, N = 135). Demineralisation solutions of microhardness measurements were used for the ICP-OES elemental analysis. The parameters for laser irradiation were as follows: power output, 0.25 W; total energy density, 62.5 J/cm 2 and energy density per pulse, 4.48 J/cm 2 with an irradiation time of 20 s and with no water cooling. Five percent NaF varnish was used as fluoride preparate. ANOVA and Tukey HSD tests were performed (α = 5%). Surface treatments showed no significant effects on shear bond strength values (p = 0.579). However, significant differences were found in microhardness measurements and in elemental analysis of Ca and P amounts (p < 0.01). Surface-treated groups showed significantly high VNH values and significantly low ICP-OES values when compared with non-treated (-control) group while there were no significance among surface-treated groups regarding VHN and ICP-OES values. Sub-ablative Er,Cr:YSGG treatment alone or combined with fluoride is as an effective method as at least fluoride alone for preventing the prepared enamel to demineralization with no negative effect on shear bond strength.

  4. Shear bond strength of two bonding systems on dentin surfaces prepared with Er:YAG laser; Resistencia de uniao ao cisalhamento de dois sistemas adesivos em superficies dentinarias preparadas com laser de Er:YAG

    Dall' Magro, Eduardo

    2001-07-01

    The purpose of this study was to examine the shear bond strength of two bonding dentin systems, one 'one step' (Single Bond - 3M) and one 'self-etching' (Prompt-L-ESPE), when applied on dentin surfaces prepared with Er:YAG laser (2,94{mu}m) that underwent ar not, acid etched. Forty one human molars just extracted were selected and after the cut with diamond disc and included in acrylic resin, resulting in 81 specimens (hemi crowns). After, the specimens were divided in one group treated with sand paper and another two groups treated with Er:YAG laser with 200 mJ and 250 mJ of energy and 2 Hz of frequency. Next, the prepared surfaces received three treatments with following application: 1) acid + Single Bond + Z 250 resin, 2) prompt-L-Pop + Z 250 resin, and 3) acid without, Single Bond + Z 250 resin. The Z 250 resin was applied and photopolymerized in increments on a Teflon matrix that belonged to an apparatus called 'Assembly Apparatus' machine producing cylinders of 3,5 mm of diameter and 5 mm of height. After these specimens were submitted to thermo cycling during 1 minute the 55 deg C and during 1 minute with 5 deg C with a total of 500 cycles for specimen, and the measures of shear bond strength were abstained using EMIC model DL 2000 rehearsed machine, with speed of 0,5 mm/min, measuring the final rupture tension (Mpa). The results showed an statistic superiority of 5% of probability level in dentin flattened with sandpaper and with laser using 200 mJ of energy with aspect to the ones flattened with laser using 250 mJ of energy. It was observed that using 'Single Bond' bonding dentin system the marks were statistically superior at 5% of probability with reference to the use of the Prompt-L-Pop adhesive system. So, it was concluded that Er:YAG Laser with 200 mJ of energy produced similar dentin cavity prepare than sandpaper and Single Bond seemed the best bonding agent system between restorative material and dentin

  5. Effect of Temperature and Electric Field on the Damping and Stiffness Characteristics of ER Fluid Short Squeeze Film Dampers

    H. P. Jagadish

    2013-01-01

    Full Text Available Squeeze film dampers are novel rotor dynamic devices used to alleviate small amplitude, large force vibrations and are used in conjunction with antifriction bearings in aircraft jet engine bearings to provide external damping as these possess very little inherent damping. Electrorheological (ER fluids are controllable fluids in which the rheological properties of the fluid, particularly viscosity, can be controlled in accordance with the requirements of the rotor dynamic system by controlling the intensity of the applied electric field and this property can be utilized in squeeze film dampers, to provide variable stiffness and damping at a particular excitation frequency. The paper investigates the effect of temperature and electric field on the apparent viscosity and dynamic (stiffness and damping characteristics of ER fluid (suspension of diatomite in transformer oil using the available literature. These characteristics increase with the field as the viscosity increases with the field. However, these characteristics decrease with increase in temperature and shear strain rate as the viscosity of the fluid decreases with temperature and shear strain rate. The temperature is an important parameter as the aircraft jet engine rotors are located in a zone of high temperature gradients and the damper fluid is susceptible to large variations in temperature.

  6. Influence of liquid phase on nanoparticle-based giant electrorheological fluid.

    Gong, Xiuqing; Wu, Jinbo; Huang, Xianxiang; Wen, Weijia; Sheng, Ping

    2008-04-23

    We show that the chemical structures of silicone oils can have an important role in the giant electrorheological (GER) effect. The interaction between silicone oils and solid nanoparticles is found to significantly influence the ER effect. By increasing the kinematic viscosity of silicone oils, which is a function of siloxane chain length, sol-like, gel-like and clay-like appearances of the constituted ER fluids were observed. Different functional-group-terminated silicone oils were also employed as the dispersing media. Significant differences of yield stress were found. We systematically study the effect of siloxane chain lengths on the permeability of oils traveling through the porous spaces between the particles (using the Washburn method), oils adsorbed on the particles' surface (using FT-IR spectra), as well as their particle size distribution (using dynamic light scattering). Our results indicate the hydrogen bonds are instrumental in linking the silicone oil to GER solid particles, and long chain lengths can enhance the agglomeration of the GER nanoparticles to form large clusters. An optimal oil structure, with hydroxyl-terminated silicone oil and a suitable viscosity, was chosen which can create the highest yield stress of ∼300 kPa under a 5 kV mm(-1) DC electric field.

  7. Viscoelastic properties of electrorheological suspensions of core-shell (carbon/polyaniline) particles in silicone oil

    Sedlačík, M.; Almajdalawi, S.; Mrlík, M.; Pavlínek, V.; Saha, P.; Stejskal, Jaroslav

    2013-01-01

    Roč. 412, č. 1 (2013), 012006_1-012006_8 ISSN 1742-6588. [International Conference on Electrorheological Fluids and Magnetorheological Suspensions /13./ - ERMR2012. Ankara, 02.07.2012-06.07.2012] R&D Projects: GA ČR GA202/09/1626 Institutional support: RVO:61389013 Keywords : polyaniline * carbonization * electrorheology Subject RIV: BK - Fluid Dynamics

  8. State of the art of medical devices featuring smart electro-rheological and magneto-rheological fluids

    Jong-Seok Oh

    2017-10-01

    Full Text Available Recently, smart fluids have drawn significant attention and growing a great interest in a broad range of engineering applications such as automotive and medical areas. In this article, two smart fluids called electro-rheological (ER fluid and magneto-rheological (MR fluid are reviewed in terms of medical applications. Especially, this article describes the attributes and inherent properties of individual medical and rehabilitation devices. The devices surveyed in this article include multi-degree-of-freedom haptic masters for robot surgery, thin membrane touch panels for braille readers, sponge-like tactile sensors to feel human tissues such as liver, rehabilitation systems such as prosthetic leg, and haptic interfaces for dental implant surgery. The operating principle, inherent characteristics and practical feasibility of each medical device or system are fully discussed in details.

  9. Electrorheological effect of Ti-bearing blast furnace slag with different TiC contents at 1500°C

    Yue, Hong-rui; Jiang, Tao; Zhang, Qiao-yi; Duan, Pei-ning; Xue, Xiang-xin

    2017-07-01

    The electrorheological properties of CaO-SiO2-Al2O3-MgO-TiO2-TiC slags were investigated to enhance understanding of the effect of TiC addition on the viscosity, yield stress, and fluid pattern of Ti-bearing slags in a direct-current electric field. The viscosities and shear stresses of 4wt% and 8wt% TiC slags were found to increase substantially with increasing electric field intensity, whereas virtually no rheological changes were observed in the 0wt% TiC slag. The Herschel-Bulkley model was applied to demonstrate that the fluid pattern of the 4wt% TiC slag was converted from that of a Newtonian fluid to that of a Bingham fluid in response to the applied electric field; and the static yield stress increased linearly with the square of the electric field intensity.

  10. Analysis of the static yield stress for giant electrorheological fluids

    Seo, Youngwook P.; Choi, Hyoung Jin; Seo, Yongsok

    2017-08-01

    Cheng et al. (2010)'s experimental results for the static yield stress of giant electrorheological (GER) fluids over the full range of electric field strengths were reanalyzed by applying Seo's scaling function which could include both the polarization and the conductivity models. The Seo's scaling function could correctly fit the yield stress behavior of GER suspensions behavior after if a proper normalization of the yield stress data was taken which collapse them onto a single curve. The model predictions were also contrasted with recently proposed Choi et al.'s scaling function to rouse the attention for a proper consideration of the GER fluid mechanisms.

  11. Temperature-dependent electrorheological effect and its description with respect to dielectric spectra

    Plachý, T.; Sedlačík, M.; Pavlínek, V.; Stejskal, Jaroslav; Pedro Graça, M.; Cadillon Costa, L.

    2016-01-01

    Roč. 27, č. 7 (2016), s. 880-886 ISSN 1045-389X. [International Conference on Electrorheological Fluids and Magnetorheological Suspensions /14./ - ERMR2014. Granada, 07.07.2014-11.07.2014] R&D Projects: GA ČR(CZ) GA13-00270S Institutional support: RVO:61389013 Keywords : electrorheology * aniline oligomers * carbonization Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.255, year: 2016

  12. Design Program in Graphic User Interface Environment for Automobile ER Devices

    Lim, S. C.; Park, J. S.; Sohn, J. W.; Choi, S. B.

    This work presents a design and analysis program for vehicle devices utilizing an electrorheological (ER) fluid. The program is operated in graphic user interface (GUI) environment and the initial window is consisted of four subprogram modules which are related to ER shock absorber, ER seat damper, ER engine mount, and ER anti-lock brake system (ABS), respectively. In order to execute each module, both material properties and design parameters are to be chosen by the user. Then, the output display window shows the field-dependent performance characteristics to be considered as design criteria. In addition, control performances of the vehicle system equipped with ER devices are displayed in time and frequency domain. In order to demonstrate the effectiveness of the proposed program, ER shock absorber and ER ABS are designed and manufactured and their performance characteristics are evaluated.

  13. Performance of a viscous damper using electro-rheological fluid

    Otani, A.; Kobayashi, H.; Kobayashi, N.; Tadaishi, Y.

    1994-01-01

    A new damper has been developed that suppresses small-amplitude vibrations over a wide frequency range. The damper has been tested using both an electro-rheological fluid (ERF) and a highly viscous liquid, which are enclosed in the damper's casing (a metal bellows). The apparent viscosity of the ERF can be changed by varying the strength of the applied electrical field. Initially, a simple L-shaped piping model excited by a rotary-type exciter was used to investigate the performance of the damper, utilizing both fluids. The experimental results demonstrate the effectiveness of the passive damper. Based on the experimental results, application of the damper to an actual piping system with a big pump was carried out analytical

  14. Microdroplet-based universal logic gates by electrorheological fluid

    Zhang, Mengying

    2011-01-01

    We demonstrate a uniquely designed microfluid logic gate with universal functionality, which is capable of conducting all 16 logic operations in one chip, with different input voltage combinations. A kind of smart colloid, giant electrorheological (GER) fluid, functions as the translation media among fluidic, electronic and mechanic information, providing us with the capability of performing large integrations either on-chip or off-chip, while the on-chip hybrid circuit is formed by the interconnection of the electric components and fluidic channels, where the individual microdroplets travelling in a channel represents a bit. The universal logic gate reveals the possibilities of achieving a large-scale microfluidic processor with more complexity for on-chip processing for biological, chemical as well as computational experiments. © 2011 The Royal Society of Chemistry.

  15. Role of symmetry-breaking induced by Er × B shear flows on developing residual stresses and intrinsic rotation in the TEXTOR tokamak

    Xu, Y.; Shesterikov, I.; Berte, M.; Dumortier, P.; Van Schoor, M.; Vergote, M.; Hidalgo, C.; Krämer-Flecken, A.; Koslowski, R.

    2013-01-01

    Direct measurements of residual stress (force) have been executed at the edge of the TEXTOR tokamak using multitip Langmuir and Mach probes, together with counter-current NBI torque to balance the existing toroidal rotation. Substantial residual stress and force have been observed at the plasma boundary, confirming the existence of a finite residual stress as possible mechanisms to drive the intrinsic toroidal rotation. In low-density discharges, the residual stress displays a quasi-linear dependence on the local pressure gradient, consistent with theoretical predictions. At high-density shots the residual stress and torque are strongly suppressed. The results show close correlation between the residual stress and the E r × B flow shear rate, suggesting a minimum threshold of the E × B flow shear required for the k ∥ symmetry breaking. These findings provide the first experimental evidence of the role of E r × B sheared flows in the development of residual stresses and intrinsic rotation. (letter)

  16. Shear Bond Strength of Composite and Ceromer Superstructures to Direct Laser Sintered and Ni-Cr-Based Infrastructures Treated with KTP, Nd:YAG, and Er:YAG Lasers: An Experimental Study.

    Gorler, Oguzhan; Hubbezoglu, Ihsan; Ulgey, Melih; Zan, Recai; Guner, Kubra

    2018-04-01

    The aim of this study was to examine the shear bond strength (SBS) of ceromer and nanohybrid composite to direct laser sintered (DLS) Cr-Co and Ni-Cr-based metal infrastructures treated with erbium-doped yttrium aluminum garnet (Er:YAG), neodymium-doped yttrium aluminum garnet (Nd:YAG), and potassium titanyl phosphate (KTP) laser modalities in in vitro settings. Experimental specimens had four sets (n = 32) including two DLS infrastructures with ceromer and nanohybrid composite superstructures and two Ni-Cr-based infrastructures with ceromer and nanohybrid composite superstructures. Of each infrastructure set, the specimens randomized into four treatment modalities (n = 8): no treatment (controls) and Er:YAG, Nd:YAG, and KTP lasers. The infrastructures were prepared in the final dimensions of 7 × 3 mm. Ceromer and nanohybrid composite was applied to the infrastructures after their surface treatments according to randomization. The SBS of specimens was measured to test the efficacy of surface treatments. Representative scanning electron microscopy (SEM) images after laser treatments were obtained. Overall, in current experimental settings, Nd:YAG, KTP, and Er:YAG lasers, in order of efficacy, are effective to improve the bonding of ceromer and nanohybrid composite to the DLS and Ni-Cr-based infrastructures (p laser is more effective in the DLS/ceromer infrastructures (p laser, as second more effective preparation, is more effective in the DLS/ceromer infrastructures (p laser modalities, in order of success, Nd:YAG, KTP, and Er:YAG, are effective to increase bonding of these structures.

  17. Control of repulsive force in a virtual environment using an electrorheological haptic master for a surgical robot application

    Oh, Jong-Seok; Choi, Seung-Hyun; Choi, Seung-Bok

    2014-01-01

    This paper presents control performances of a new type of four-degrees-of-freedom (4-DOF) haptic master that can be used for robot-assisted minimally invasive surgery (RMIS). By adopting a controllable electrorheological (ER) fluid, the function of the proposed master is realized as a haptic feedback as well as remote manipulation. In order to verify the efficacy of the proposed master and method, an experiment is conducted with deformable objects featuring human organs. Since the use of real human organs is difficult for control due to high cost and moral hazard, an excellent alternative method, the virtual reality environment, is used for control in this work. In order to embody a human organ in the virtual space, the experiment adopts a volumetric deformable object represented by a shape-retaining chain linked (S-chain) model which has salient properties such as fast and realistic deformation of elastic objects. In haptic architecture for RMIS, the desired torque/force and desired position originating from the object of the virtual slave and operator of the haptic master are transferred to each other. In order to achieve the desired torque/force trajectories, a sliding mode controller (SMC) which is known to be robust to uncertainties is designed and empirically implemented. Tracking control performances for various torque/force trajectories from the virtual slave are evaluated and presented in the time domain. (paper)

  18. Control of repulsive force in a virtual environment using an electrorheological haptic master for a surgical robot application

    Oh, Jong-Seok; Choi, Seung-Hyun; Choi, Seung-Bok

    2014-01-01

    This paper presents control performances of a new type of four-degrees-of-freedom (4-DOF) haptic master that can be used for robot-assisted minimally invasive surgery (RMIS). By adopting a controllable electrorheological (ER) fluid, the function of the proposed master is realized as a haptic feedback as well as remote manipulation. In order to verify the efficacy of the proposed master and method, an experiment is conducted with deformable objects featuring human organs. Since the use of real human organs is difficult for control due to high cost and moral hazard, an excellent alternative method, the virtual reality environment, is used for control in this work. In order to embody a human organ in the virtual space, the experiment adopts a volumetric deformable object represented by a shape-retaining chain linked (S-chain) model which has salient properties such as fast and realistic deformation of elastic objects. In haptic architecture for RMIS, the desired torque/force and desired position originating from the object of the virtual slave and operator of the haptic master are transferred to each other. In order to achieve the desired torque/force trajectories, a sliding mode controller (SMC) which is known to be robust to uncertainties is designed and empirically implemented. Tracking control performances for various torque/force trajectories from the virtual slave are evaluated and presented in the time domain.

  19. Electrorheological properties of suspensions of hollow globular titanium oxide/polypyrrole particles

    Sedlačík, M.; Mrlík, M.; Pavlínek, V.; Sáha, P.; Quadrat, Otakar

    2012-01-01

    Roč. 290, č. 1 (2012), s. 41-48 ISSN 0303-402X R&D Projects: GA ČR GA202/09/1626 Institutional research plan: CEZ:AV0Z40500505 Keywords : electrorheology * titanium oxide * hollow globular clusters Subject RIV: JI - Composite Materials Impact factor: 2.161, year: 2012

  20. An electrorheological investigation of PVB solutions in connection with their electrospinning qualities

    Peer, Petra; Stěnička, M.; Pavlínek, V.; Filip, Petr; Kuřitka, I.; Brus, Jiří

    2014-01-01

    Roč. 39, October (2014), s. 115-121 ISSN 0142-9418 R&D Projects: GA ČR(CZ) GAP105/11/2342 Institutional support: RVO:67985874 ; RVO:61389013 Keywords : electrospinning * nanofibres * polyvinylbutyral * electrorheology * polymer solution Subject RIV: BK - Fluid Dynamics; CD - Macromolecular Chemistry (UMCH-V) Impact factor: 2.240, year: 2014

  1. Comparison of electrorheological characteristics obtained for two geometries: parallel plates and concentric cylinders

    Peer, Petra; Filip, Petr; Stěnička, M.; Pavlínek, V.

    2014-01-01

    Roč. 59, č. 3 (2014), s. 221-235 ISSN 0001-7043 R&D Projects: GA ČR(CZ) GAP105/11/2342 Institutional support: RVO:67985874 Keywords : electrorheology * parallel plates * concentric cylinders * silicone oil * PANI powders Subject RIV: BK - Fluid Dynamics

  2. Comparison of electrorheological measurements using different geometries in two commercial rotational rheometers

    Peer, Petra; Filip, Petr; Stěnička, M.; Pavlínek, V.

    2017-01-01

    Roč. 2, č. 1 (2017), s. 20-24 ISSN 2405-4658 Institutional support: RVO:67985874 Keywords : Anton Paar MCR 501 * electrocells * electrorheology * Gemini CVOR 150 * rheological characteristics Subject RIV: BK - Fluid Dynamics OBOR OECD: Fluids and plasma physics (including surface physics)

  3. An effect of carbonization on the electrorheology of poly(p-phenylenediamine)

    Plachý, T.; Sedlačík, M.; Pavlinek, V.; Morávková, Zuzana; Hajná, Milena; Stejskal, Jaroslav

    2013-01-01

    Roč. 63, November (2013), s. 187-195 ISSN 0008-6223 R&D Projects: GA ČR GA202/09/1626 Institutional support: RVO:61389013 Keywords : carbonization * electrorheology * poly(p-phenylenediamine) Subject RIV: BK - Fluid Dynamics Impact factor: 6.160, year: 2013

  4. The effect of compatibility of suspension particles with the oil medium on electrorheological efficiency

    Stěnička, M.; Pavlínek, V.; Sáha, P.; Blinova, Natalia V.; Stejskal, Jaroslav; Quadrat, Otakar

    2012-01-01

    Roč. 23, č. 9 (2012), s. 1055-1059 ISSN 1045-389X R&D Projects: GA ČR GA202/09/1626; GA AV ČR IAA400500905 Institutional research plan: CEZ:AV0Z40500505 Keywords : electrorheological * suspension * polyaniline Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.523, year: 2012

  5. Operational durability of a giant ER valve for Braille display

    Luning, Xu; Han, Li; Yufei, Li; Shen, Rong; Kunquan, Lu

    2017-05-01

    The compact configuration of giant ER (electrorheological) valves provides the possibility of realizing a full-page Braille display. The operational durability of ER valves is a key issue in fulfilling a Braille display. A giant ER valve was used to investigate the variations in pressure drops and critical pressure drops of the valves over a long period under some typical operational parameters. The results indicate that neither the pressure drops nor critical pressure drops of giant ER valves show apparent deterioration over a long period. Without ER fluid exchange, a blockage appears in the channel of the valve because the ER structures induced by an external electric field cannot be broken by the Brownian motion of hydraulic oil molecules when the external electric field is removed. Forcing ER fluid flow is an effective and necessary method to keep the channel of the valve unblocked. Thus the operational durability of the valve using giant ER fluids is able to meet the demands of Braille display.

  6. Forflytning: shear og friktion

    2005-01-01

    friktion). Formålet med filmprojektet er: At give personalet i Apopleksiafsnittet viden om shear og friktion, så det motiveres til forebyggelse. Mål At udarbejde et enkelt undervisningsmateriale til bed-side-brug Projektbeskrivelse (resume) Patienter med apopleksi er særligt udsatte for tryksår, fordi de...... ofte er immobile, har svært ved at opretholde en god siddestilling eller ligger tungt i sengen som følger efter apopleksien Hvis personalet bruger forkert lejrings-og forflytningsteknik, udsættes patienterne for shear og friktion. Målgruppen i projektet er de personer, der omgås patienterne, dvs...

  7. Comparison of electrorheological measurements based on different methods of electric field generation

    Peer, Petra; Stěnička, M.; Filip, Petr; Pavlinek, V.

    2014-01-01

    Roč. 24, č. 4 (2014), 42875-1-42875-4 ISSN 1430-6395 R&D Projects: GA ČR(CZ) GAP105/11/2342 Institutional support: RVO:67985874 Keywords : rheology * electrorheology * rheometry * PANI powder * silicone oil Subject RIV: BK - Fluid Dynamics Impact factor: 1.078, year: 2014 http://www.ar.ethz.ch/TMPPDF/24394938472.192/ApplRheol_24_42875.pdf

  8. Supersonic flutter suppression of electrorheological fluid-based adaptive panels resting on elastic foundations using sliding mode control

    Hasheminejad, Seyyed M; Nezami, M; Aryaee Panah, M E

    2012-01-01

    Brief reviews on suppressing panel flutter vibrations by various active control strategies as well as utilization tunable electrorheological fluids (ERFs) for vibration control of structural systems are presented. Active suppression of the supersonic flutter motion of a simply supported sandwich panel with a tunable ERF interlayer, and coupled to an elastic foundation, is subsequently investigated. The structural formulation is based on the classical beam theory along with the Winkler–Pasternak foundation model, the ER fluid core is modeled as a first-order Kelvin–Voigt material, and the quasi-steady first-order supersonic piston theory is employed to describe the aerodynamic loading. Hamilton’s principle is used to derive a set of fully coupled dynamic equations of motion. The generalized Fourier expansions in conjunction with the Galerkin method are then employed to formulate the governing equations in the state space domain. The critical dynamic pressures at which unstable panel oscillations (coalescence of eigenvalues) occur are obtained via the p-method for selected applied electric field strengths (E = 0,2,4 kV mm −1 ). The classical Runge–Kutta time integration algorithm is subsequently used to calculate the open-loop aeroelastic response of the system in various basic loading configurations (i.e. uniformly distributed blast, gust, sonic boom, and step loads), with or without an interacting soft/stiff elastic foundation. Finally, a sliding mode control synthesis (SMC) involving the first six natural modes of the structural system is set up to actively suppress the closed-loop system response in supersonic flight conditions and under the imposed excitations. Simulation results demonstrate performance, effectiveness, and insensitivity with respect to the spillover of the proposed SMC-based control system. Limiting cases are considered and good agreements with the data available in the literature as well as with the computations made by using the

  9. Investigation of the touch sensitivity of ER fluid based tactile display

    Liu, Yanju; Davidson, Rob; Taylor, Paul

    2005-05-01

    A tactile display is programmable device whose controlled surface is intended to be investigated by human touch. It has a great number of potential applications in the field of virtual reality and elsewhere. In this research, a 5x5 touch sensitive tactile display array including electrorheological (ER) fluid has been developed and investigated. Experimental results show that the sensed surface information could be controlled effectively by adjusting the voltage activation pattern imposed on the tactels. In the meantime, it is possible to sense the touching force normal to the display"s surface by monitoring the change of current passing through the ER fluid. These encouraging results are helpful for constructing a new type of tactile display based on ER fluid which can act as both sensor and actuator at the same time.

  10. Modeling and control of an off-road truck using electrorheological dampers

    Holzmann, K; Kemmetmueller, W; Kugi, A; Stork, M; Rosenfeldt, H; Schneider, S

    2009-01-01

    This work deals with the mathematical modeling and control of the semi-active suspension of an MAN off-road truck with a payload of 5 tons which comprises electrorheological dampers. Thereby, a cascaded control structure with four controllers for the control of a quarter-car in the inner control loop and a superimposed control strategy for the overall vehicle is used. The main goal of the control strategy is to reduce the motion of the chassis (especially roll, pitch and vertical movement) while increasing driving stability. The capability of the overall control strategy is demonstrated by means of simulation studies and measurement results.

  11. Shear machines

    Astill, M.; Sunderland, A.; Waine, M.G.

    1980-01-01

    A shear machine for irradiated nuclear fuel elements has a replaceable shear assembly comprising a fuel element support block, a shear blade support and a clamp assembly which hold the fuel element to be sheared in contact with the support block. A first clamp member contacts the fuel element remote from the shear blade and a second clamp member contacts the fuel element adjacent the shear blade and is advanced towards the support block during shearing to compensate for any compression of the fuel element caused by the shear blade (U.K.)

  12. Electrorheology of silicone oil suspensions of urea-modified poly[(glycidyl methacrylate)-co-(ethylene dimethacrylate)] particles

    Belza, T.; Pavlínek, V.; Sáha, P.; Beneš, Milan J.; Horák, Daniel; Quadrat, Otakar

    2007-01-01

    Roč. 385, č. 1 (2007), s. 1-8 ISSN 0378-4371 R&D Projects: GA MŠk 2B06053 Institutional research plan: CEZ:AV0Z40500505 Keywords : Electrorheology * Suspension * Poly(glycidyl methacrylate-co-(ethylene dimethacrylate) Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.430, year: 2007

  13. Mechanical and electro-rheological properties of electrospun poly(vinyl alcohol) nanofibre mats filled with carbon black nanoparticles

    Chuangchote, Surawut; Sirivat, Anuvat; Supaphol, Pitt

    2007-01-01

    The present contribution reports, for the first time, the mechanical and electro-rheological properties of electrospun poly(vinyl alcohol) (PVA) nanofibre mats with or without the incorporation of carbon black (CB) nanoparticles. The effects of sonication and the addition of CB on morphological appearance, average diameter of the as-spun fibre mats, and that of the individual fibres, were thoroughly investigated. Incorporation of CB (1-10% based on the weight of PVA) in 10% w/v PVA solution did not affect the morphology and average diameter of the obtained fibres (∼160 nm), but it affected both the mechanical and the electro-rheological properties of the as-spun PVA/CB fibre mats, in which the mats became more rigid with the addition and increasing amount of CB

  14. Observation of neoclassical transport in reverse shear plasmas on TFTR

    Efthimion, P.C.; Goeler, S. von; Houlberg, W.A.

    1999-01-01

    Perturbative experiments on TFTR have investigated the transport of multiple ion species in reverse shear (RS) plasmas. The profile evolutions of trace tritium and helium and intrinsic carbon indicate the formation of core particle transport barriers in enhanced reverse shear (ERS) plasmas. There is an order of magnitude reduction in the particle diffusivity inside the RS region. The diffusivities for these species in ERS plasmas agree with neoclassical theory. (author)

  15. Politik er ikke lykken

    Steenbuch, Johannes Aakjær

    2011-01-01

    Der er ikke længere nogen højere sandhed i livet end den, flertallet bestemmer sig for – og dermed ingen del af livet, der ikke er politisk. Højre- og venstrefløjen er i bund og grund enige - enige om, at det er politikernes opgave at forære os det gode liv. Dermed bliver demokratiet totalitært. ...

  16. Man er aldrig alene

    Hoffmeyer, Jesper

    2013-01-01

    Nu ved vi, at der er mange slags DNA i vores krop, og at samarbejdet mellem de organismer, som bærer alt dette DNA, er essentielt for vores overlevelse" … "Kroppen er en slags økosystem, hvor alle slags samarbejde hen ad vejen bliver afprøvet"...

  17. New electrorheological fluids - characteristics and implementation in industrial and mobile applications

    Gurka, M; Adams, D; Johnston, L; Petricevic, R

    2009-01-01

    Various applications for controllable dampers in the industrial and automotive sector are demanding an improved ER-Fluid, concerning performance and long time behavior. The new ER-Fluid RheOil (registered) 3.0 developed by us and presented here overcomes the main disadvantages like sedimentation and re-dispersing behavior. Besides this, better ER-performance (control ratio, current-density, step response time) could also be achieved. During tests of the response to changing temperature and long time behavior no significant degradation of the fluid or abrasive wear in the components was found over a wide temperature range.

  18. Neoclassical transport in ERS regime

    Lin, Z.; Tang, W.; Lee, W.W.

    1996-01-01

    The core ion thermal conductivity has been observed to fall below the standard neoclassical level in recent TFTR reversed magnetic shear discharges. Due to the combination of high central q and small local inverse aspect ratio, the ion poloidal gyroradius can be larger than the minor radius and comparable to the pressure gradient scale length in this ERS regime. It is then expected that finite orbit width effects play a key role in modifying the standard picture of neoclassical transport. Specifically, both the trapped particle fraction and the banana orbit width axe reduced by the finite minor radius and possibly by the pressure-gradient-driven radial electric field. In addition, the steep pressure gradient can generate neoclassical poloidal flows which, in turn, could reduce the particle and heat transports. Results from analytic estimates as well as those from full toroidal gyrokinetic neoclassical simulations will be presented

  19. Modeling and Design of an Electro-Rheological Fluid Based Haptic System for Tele-Operation of Space Robots

    Mavroidis, Constantinos; Pfeiffer, Charles; Paljic, Alex; Celestino, James; Lennon, Jamie; Bar-Cohen, Yoseph

    2000-01-01

    For many years, the robotic community sought to develop robots that can eventually operate autonomously and eliminate the need for human operators. However, there is an increasing realization that there are some tasks that human can perform significantly better but, due to associated hazards, distance, physical limitations and other causes, only robot can be employed to perform these tasks. Remotely performing these types of tasks requires operating robots as human surrogates. While current "hand master" haptic systems are able to reproduce the feeling of rigid objects, they present great difficulties in emulating the feeling of remote/virtual stiffness. In addition, they tend to be heavy, cumbersome and usually they only allow limited operator workspace. In this paper a novel haptic interface is presented to enable human-operators to "feel" and intuitively mirror the stiffness/forces at remote/virtual sites enabling control of robots as human-surrogates. This haptic interface is intended to provide human operators intuitive feeling of the stiffness and forces at remote or virtual sites in support of space robots performing dexterous manipulation tasks (such as operating a wrench or a drill). Remote applications are referred to the control of actual robots whereas virtual applications are referred to simulated operations. The developed haptic interface will be applicable to IVA operated robotic EVA tasks to enhance human performance, extend crew capability and assure crew safety. The electrically controlled stiffness is obtained using constrained ElectroRheological Fluids (ERF), which changes its viscosity under electrical stimulation. Forces applied at the robot end-effector due to a compliant environment will be reflected to the user using this ERF device where a change in the system viscosity will occur proportionally to the force to be transmitted. In this paper, we will present the results of our modeling, simulation, and initial testing of such an

  20. Vreden er over os

    Mehlsen, Camilla

    2006-01-01

    Urolige elever, cyklister - der giver fuck-finger, aggressive demonstranter. Samtiden er på vej ind i en æra domineret af vrede, siger rektor Lars-Henrik Schmidt, der er aktuel med bogen 'Om vreden'. Udgivelsesdato: Juni......Urolige elever, cyklister - der giver fuck-finger, aggressive demonstranter. Samtiden er på vej ind i en æra domineret af vrede, siger rektor Lars-Henrik Schmidt, der er aktuel med bogen 'Om vreden'. Udgivelsesdato: Juni...

  1. Hvad f er meningen?

    Rydén, Pernille; Ringberg, Torsten; Wilke, Ricky

    En forskningsrapport fra CBS om danske lederes opfattelse af sociale medier i detail- og servicebranchen. Rapporten er udarbejdet i regi af Service Platform.......En forskningsrapport fra CBS om danske lederes opfattelse af sociale medier i detail- og servicebranchen. Rapporten er udarbejdet i regi af Service Platform....

  2. Fluxus-øer

    van der Meijden, Peter Alexander

    2008-01-01

    "Fluxus-øer" er en introduktion til Fluxus med udgangspunkt i den tyske galleri-ejer René Blocks samling, som udstillingen "Food for Thought" i Sukkerfabrikken i Stege (Møn) præsenterede et udvalg af. Artiklen beskriver Fluxus som et heterotopi som beskrevet af Michel Foucault i "Of Other Spaces"...

  3. MIT HJEM ER HVOR MIT HJERTE ER

    Høst, Jeppe Engset

    2014-01-01

    Ideen om at arbejde med det man kalder de stedbundne ressourcer på en ny måde, er relevant på Bornholm hvor events som blandt andet festivalen ’Wonderfestiwall’, strandfesten ’Vang Pier Beach Party’, karnevallet ’Svaneke Beach Party, kokkekonkurrencen ’Sol over Gudhjem’ og filmfestivalen ’Bornsho...

  4. Optimal control of transient processes in an oscillating system with an electrorheological shock-absorber

    Reizina, G N [National Technical University, 65 Nezavisimosti Avenue, Minsk, 220013 (Belarus); Korobko, E V; Bilyk, V A [Luikov Heat and Mass Transfer Institute of NASB, 15 P Brovki Street, Minsk, 220072 (Belarus); Efremov, V L; Binshtok, A E [Minsk Wheel Tractor Plant, 150 Partizanskii Avenue, Minsk, 220021 (Belarus)], E-mail: eva@itmo.by

    2009-02-01

    The problem of optimal control of the oscillation of a driver's seat with ER shock absorber is discussed in application to vehicles based on the principle of maximum. Coordinates of a vector of the control parameter and vertical motions of a seat are obtained. Test experimental investigations on working regimes for the driver's seat model depending on the controlling impact of the electrical signal (the intensity of the electric field) were performed.

  5. Hvor anvendelig er PKI?

    Nielsen, Jon Magne

    2006-01-01

    Denne oppgaven ser på bruken av elektronisk ID i statlige etater i Norge i dag. Det ses spesielt på om bruken av tekologien PKI er en god løsning på etatenes behov på dette området. Som utgangspunkt for analysen er det sett spesielt på to statlige etater. Disse etatenes behov og bruk av elektronisk ID generelt og PKI spesielt blir undersøkt. Det er videre gjort rede for hvilke lover, forskrifter og andre førende dokumenter som danner de formelle rammebetingelsene for etaters bruk av PKI. ...

  6. a New ER Fluid Based Haptic Actuator System for Virtual Reality

    Böse, H.; Baumann, M.; Monkman, G. J.; Egersdörfer, S.; Tunayar, A.; Freimuth, H.; Ermert, H.; Khaled, W.

    The concept and some steps in the development of a new actuator system which enables the haptic perception of mechanically inhomogeneous virtual objects are introduced. The system consists of a two-dimensional planar array of actuator elements containing an electrorheological (ER) fluid. When a user presses his fingers onto the surface of the actuator array, he perceives locally variable resistance forces generated by vertical pistons which slide in the ER fluid through the gaps between electrode pairs. The voltage in each actuator element can be individually controlled by a novel sophisticated switching technology based on optoelectric gallium arsenide elements. The haptic information which is represented at the actuator array can be transferred from a corresponding sensor system based on ultrasonic elastography. The combined sensor-actuator system may serve as a technology platform for various applications in virtual reality, like telemedicine where the information on the consistency of tissue of a real patient is detected by the sensor part and recorded by the actuator part at a remote location.

  7. Control of an ER haptic master in a virtual slave environment for minimally invasive surgery applications

    Han, Young-Min; Choi, Seung-Bok

    2008-01-01

    This paper presents the control performance of an electrorheological (ER) fluid-based haptic master device connected to a virtual slave environment that can be used for minimally invasive surgery (MIS). An already developed haptic joint featuring controllable ER fluid and a spherical joint mechanism is adopted for the master system. Medical forceps and an angular position measuring device are devised and integrated with the joint to establish the MIS master system. In order to embody a human organ in virtual space, a volumetric deformable object is used. The virtual object is then mathematically formulated by a shape-retaining chain-linked (S-chain) model. After evaluating the reflection force, computation time and compatibility with real-time control, the haptic architecture for MIS is established by incorporating the virtual slave with the master device so that the reflection force for the object of the virtual slave and the desired position for the master operator are transferred to each other. In order to achieve the desired force trajectories, a sliding mode controller is formulated and then experimentally realized. Tracking control performances for various force trajectories are evaluated and presented in the time domain

  8. Innovation er brugerdreven!

    Helms, Niels Henrik

    2008-01-01

    Brugerdreven innovation er blevet svaret på mange af de udfordringer, som vores moderne samfund står overfor.Det er skrevet ind i såvel regeringsgrundlaget som i de forskellige tiltag, som skal ruste Danmark i forhold til globaliseringen. Vi har ifølge argumentationen her enrække særlige forudsæt....... Udgivelsesdato: marts 2008...

  9. Metabolomics er fremtiden

    Pedersern, Birger

    2010-01-01

    Forskningen i fødevarer har fået et potent redskab i hånden. Metabolomics er vejen frem, mener professor Søren Balling Engelsen fra Københavns Universitet......Forskningen i fødevarer har fået et potent redskab i hånden. Metabolomics er vejen frem, mener professor Søren Balling Engelsen fra Københavns Universitet...

  10. Er KU et mobbeuniversitet?

    Olden-Jørgensen, Sebastian

    2009-01-01

    Ansatte på KU mobber hverken mere eller mindre end på andre danske arbejdspladser. Mediernes dækning af APV-undersøgelsens resultater mht. mobning er sensationalistisk og delvis vildledende.......Ansatte på KU mobber hverken mere eller mindre end på andre danske arbejdspladser. Mediernes dækning af APV-undersøgelsens resultater mht. mobning er sensationalistisk og delvis vildledende....

  11. Er jeres ledere 'likeable'?

    Nielsen, Rikke Kristine

    2013-01-01

    Færdigheder: Oftest er lederne langtfra de første til at kaste sig over ny teknologi. It-kundskaberne på chefgangen trænger til en opgradering.......Færdigheder: Oftest er lederne langtfra de første til at kaste sig over ny teknologi. It-kundskaberne på chefgangen trænger til en opgradering....

  12. er 1999

    Jensen, J. P.; Søndergaard, M.; Jeppesen, E.

    små cladoceer og hjuldyr, og især er maksimumsforekom-sterne af calanoide vandlopper og de små og store cladoceer og daf-nier gået tilbage. Den gennemsnitlige biomasse af dafnier er derimod øget især p.g.a. stigning i de 25 % af søerne med størst forekomster. Dyreplanktons græsning Betragtet under et...

  13. er 2000

    Jensen, J. P.; Søndergaard, M.; Jeppesen, E.

    styrke det fagli-ge grundlag for de mil-jøpolitiske prioriteringer og beslut-ninger. En væsentlig del af denne opgave er overvågning af miljø og natur. Det er derfor et naturligt led i Danmarks Miljø-undersø-gelsers opgave at forestå den landsdækkende rapportering af overvågnings-program-met inden...

  14. Design and Implementation of a High-Voltage Generator with Output Voltage Control for Vehicle ER Shock-Absorber Applications

    Chih-Lung Shen

    2013-01-01

    Full Text Available A self-oscillating high-voltage generator is proposed to supply voltage for a suspension system in order to control the damping force of an electrorheological (ER fluid shock absorber. By controlling the output voltage level of the generator, the damping force in the ER fluid shock absorber can be adjusted immediately. The shock absorber is part of the suspension system. The high-voltage generator drives a power transistor based on self-excited oscillation, which converts dc to ac. A high-frequency transformer with high turns ratio is used to increase the voltage. In addition, the system uses the car battery as dc power supply. By regulating the duty cycle of the main switch in the buck converter, the output voltage of the buck converter can be linearly adjusted so as to obtain a specific high voltage for ER. The driving system is self-excited; that is, no additional external driving circuit is required. Thus, it reduces cost and simplifies system structure. A prototype version of the actual product is studied to measure and evaluate the key waveforms. The feasibility of the proposed system is verified based on experimental results.

  15. A haptic sensor-actor-system based on ultrasound elastography and electrorheological fluids for virtual reality applications in medicine.

    Khaled, W; Ermert, H; Bruhns, O; Boese, H; Baumann, M; Monkman, G J; Egersdoerfer, S; Meier, A; Klein, D; Freimuth, H

    2003-01-01

    Mechanical properties of biological tissue represent important diagnostic information and are of histological relevance (hard lesions, "nodes" in organs: tumors; calcifications in vessels: arteriosclerosis). The problem is, that such information is usually obtained by digital palpation only, which is limited with respect to sensitivity. It requires intuitive assessment and does not allow quantitative documentation. A suitable sensor is required for quantitative detection of mechanical tissue properties. On the other hand, there is also some need for a realistic mechanical display of those tissue properties. Suitable actuator arrays with high spatial resolution and real-time capabilities are required operating in a haptic sensor actuator system with different applications. The sensor system uses real time ultrasonic elastography whereas the tactile actuator is based on electrorheological fluids. Due to their small size the actuator array elements have to be manufactured by micro-mechanical production methods. In order to supply the actuator elements with individual high voltages a sophisticated switching and control concept have been designed. This haptic system has the potential of inducing real time substantial forces, using a compact lightweight mechanism which can be applied to numerous areas including intraoperative navigation, telemedicine, teaching, space and telecommunication.

  16. Rab7a modulates ER stress and ER morphology.

    Mateus, Duarte; Marini, Elettra Sara; Progida, Cinzia; Bakke, Oddmund

    2018-05-01

    The Endoplasmic Reticulum (ER) is a membranous organelle with diverse structural and functional domains. Peripheral ER includes interconnected tubules, and dense tubular arrays called "ER matrices" together with bona fide flat cisternae. Transitions between these states are regulated by membrane-associated proteins and cytosolic factors. Recently, the small GTPases Rab10 and Rab18 were reported to control ER shape by regulating ER dynamics and fusion. Here, we present evidence that another Rab protein, Rab7a, modulates the ER morphology by controlling the ER homeostasis and ER stress. Indeed, inhibition of Rab7a expression by siRNA or expression of the dominant negative mutant Rab7aT22 N, leads to enlargement of sheet-like ER structures and spreading towards the cell periphery. Notably, such alterations are ascribable neither to a direct modulation of the ER shaping proteins Reticulon-4b and CLIMP63, nor to interactions with Protrudin, a Rab7a-binding protein known to affect the ER organization. Conversely, depletion of Rab7a leads to basal ER stress, in turn causing ER membrane expansion. Both ER enlargement and basal ER stress are reverted in rescue experiments by Rab7a re-expression, as well as by the ER chemical chaperone tauroursodeoxycholic acid (TUDCA). Collectively, these findings reveal a new role of Rab7a in ER homeostasis, and indicate that genetic and pharmacological ER stress manipulation may restore ER morphology in Rab7a silenced cells. Copyright © 2018 Elsevier B.V. All rights reserved.

  17. Jeg Er blevet FRANKofil

    Andersson, Lasse

    2014-01-01

    afhængig af Frank Underwood fra serien House of Cards på den fremadstormende TV-streamingstjenesten Netflix. Jeg har opdaget et nyt internetbaseret datingforhold. Et surrealt, fedt miks af det kyniske og joviale personificeret i karakteren Frank Underwood, som er helt igennem ubehagelig, men fantastisk...... spillet af Kevin Spacey. Og tak til Spacey der for en tid har forladt teateret ’The Old Vic’ i London for at begejstre mig. Der er generelt to årsager til mine FRANKofile tilbøjeligheder. For det første er Netflix’s remake af den tyve år gamle BBC serie House of Cards efter min menig et stykke tv...... anden grund, til at jeg er blevet Frankofil, er, at jeg ikke skal sidde og vente på næste søndag efter søndag efter søndag for at få lov at se næste afsnit. Netflix lagde alle tretten timer af sæson 2 ud på nettet. Jeg afgør selv, hvornår jeg skal have mere Frank! Men på trods af mit narkomanlignende...

  18. Observation of neoclassical transport in reverse shear plasmas on the tokamak fusion test reactor

    Efthimion, P.C.; Goeler, S. von; Houlberg, W.A.

    2001-01-01

    Perturbative experiments on the Tokamak Fusion Test Reactor (TFTR) have investigated the transport of multiple ion species in reverse shear plasmas. The profile evolution of trace tritium and helium, and intrinsic carbon indicate the formation of core particle transport barriers in ERS plasmas. There is an order of magnitude reduction in the particle diffusivity inside the reverse shear region. The diffusivities for these species in ERS plasmas agree with neoclassical theory. (author)

  19. Observation of neoclassical transport in reverse shear plasmas on the tokamak fusion test reactor

    Efthimion, P.C.; Von Goeler, S.; Houlberg, W.A.

    1999-01-01

    Perturbative experiments on the Tokamak Fusion Test Reactor (TFTR) have investigated the transport of multiple ion species in reverse shear plasmas. The profile evolution of trace tritium and helium, and intrinsic carbon indicate the formation of core particle transport barriers in ERS plasmas. There is an order of magnitude reduction in the particle diffusivity inside the reverse shear region. The diffusivities for these species in ERS plasmas agree with neoclassical theory. (author)

  20. Ondskaben er fortryllende

    Schubart, Rikke

    2013-01-01

    Indlæg om tv-serien Once Upon a Time (2011-), der hører til genren fairytale fantasy, der blander eventyr og fantasy. Her bliver alle eventyr brugt i en fortælling om alle beboere i en lille by, der ikke ved, at de i virkeligheden er eventyr-karakterer.......Indlæg om tv-serien Once Upon a Time (2011-), der hører til genren fairytale fantasy, der blander eventyr og fantasy. Her bliver alle eventyr brugt i en fortælling om alle beboere i en lille by, der ikke ved, at de i virkeligheden er eventyr-karakterer....

  1. Scenen er blevet din

    Helms, Niels Henrik

    2008-01-01

    Verden kan betragtes som en skueplads med mange forskellige scener. I bidrgaet vil læseren kunne stifte bekendtskab med forskellige refleksioner over netop denne metaforik som analyseoptik i forhold til begrebet innovation. Afsættet er ønsket om at finde en måde at analysere og begrebsliggøre inn...

  2. Er tang fremtidens superfood?

    Holdt, Susan Løvstad

    seneste år fået øjnene op for tang indenfor områderne: biokemikalier og bioaktive stoffer, ekstraktion, gastronomi, produktudvikling, foder, bioraffinaderier, dyrkning osv. Men hvad er det tang kan? Dette foredrag vil vise at vi med tangdyrkning kan rykke mere bæredygtig fødevareproduktion ud på havet...

  3. Ideologi er noget bras

    Hansen, Brian Benjamin; Bjerre, Henrik Jøker

    fra den slovenske filosof Slavoj Zizek stilles imidlertid det spørgsmål i bogen, om ideologien idag ikke blot har taget en anden form. Vi lever i dag ikke i post-ideologiske tider. Snarere er braset selv – X Factor, forbrugsobjekter, underholdning, følelser og balloner – blevet den næsten usynlige...

  4. Riget - alt er tilladt

    2017-01-01

    Riget indtager en nøglestilling, når overgangen mellem faser i Triers produktion skal karakteriseres. Riget danner bro mellem den billedfascination og de radikale stileksperimenter, der præger Triers tidlige produktion, og den genre- og plotbevidsthed, der er typisk for film som Breaking the Waves...

  5. Hvad er tidligt sprog

    Skriver Jensen, Anders

    2009-01-01

    Forfatteren argumenterer for at "early literacy" kan oversættes til "tidligt sprog"; særligt når der er tale om en helhedsorienteret tilgang med vægt på sprog som et alsidigt medie for kommunikation- og betydningsskabelse. Med inspiration fra Jerome Bruners kulturpsykologi diskuteres mulige...

  6. Er danskerne racister

    Bech, Henning; Necef, Mehmet Ümit

    Igennem de seneste årtier er det blevet almindeligt at tale om, at der er en udbredt racisme i Danmark. Påstande om danskernes racisme, fremmedhad og diskrimination optræder dagligt i offentligheden og i medierne, og der henvises ofte til, hvad ’forskerne’ og de ’videnskabelige undersøgelser’ siger...... om emnet. Der kan da næppe heller være tvivl om, at der forekommer racistiske holdninger hos nogle danskere. Men er problemet så stort, som det gøres til i den offentlige debat? Bogen ønsker at afklare, hvorvidt der er videnskabelig dokumentation for påstandene om danskernes racisme. Den går i dybden...... med en række forskeres og eksperters udtalelser på området og præsenterer en grundig analyse af deres fremstilling af dansk racisme i forhold til emner som kultur, seksualitet, kriminalitet og arbejdsmarked....

  7. Semiconductor laser shearing interferometer

    Ming Hai; Li Ming; Chen Nong; Xie Jiaping

    1988-03-01

    The application of semiconductor laser on grating shearing interferometry is studied experimentally in the present paper. The method measuring the coherence of semiconductor laser beam by ion etching double frequency grating is proposed. The experimental result of lens aberration with semiconductor laser shearing interferometer is given. Talbot shearing interferometry of semiconductor laser is also described. (author). 2 refs, 9 figs

  8. Er HR ude i tovene?

    Poulfelt, Flemming

    2015-01-01

    HR: Er der behov for nytænkning i HR-land? Artikler i Harvard Business Review - bakket op af en dansk undersøgelse - konkluderer, at HR stadig mangler gennemslagskraft i virksomhederne. Er HR ude i tovene? ... For i undersøgelsen "Ny Dansk Ledelse" (maj 2015), som er baseret på danske lederes...

  9. Facebook er internettet nu

    Tække, Jesper

    2014-01-01

    Den store vision for world wide web var, at alle kunne få ubegrænset adgang til alverdens information. www var mangfoldigt og anarkistisk. I dag er der rigtig mange, der kun bruger nettet til at være på Facebook. Hvad bruger Facebook det til? Og hvad gør det ved vores udsyn?......Den store vision for world wide web var, at alle kunne få ubegrænset adgang til alverdens information. www var mangfoldigt og anarkistisk. I dag er der rigtig mange, der kun bruger nettet til at være på Facebook. Hvad bruger Facebook det til? Og hvad gør det ved vores udsyn?...

  10. Hvad er en by?

    Parby, Jakob; Thelle, Mikkel

    2011-01-01

    Nytænkning. Med de moderne megabyer er det slut med at forestille sig byen som noget, man planlægger og giver form. Vi skal lære at se dem som vildtvoksende urbane landskaber. Artikel om megabyer, byudvikling og forestillingen om byen gennem tiderne. Skrevet delvist i anledning af åbningen af...... udstillingen Citambulos på Københavns Museum, der handlede om Mexico City....

  11. Theory of ion Bernstein wave induced shear suppression of turbulence

    Craddock, G. G.; Diamond, P. H.; Ono, M.; Biglari, H.

    1994-06-01

    The theory of radio frequency induced ion Bernstein wave- (IBW) driven shear flow in the edge is examined, with the goal of application of shear suppression of fluctuations. This work is motivated by the observed confinement improvement on IBW heated tokamaks [Phys. Fluids B 5, 241 (1993)], and by previous low-frequency work on RF-driven shear flows [Phys. Rev. Lett. 67, 1535 (1991)]. It is found that the poloidal shear flow is driven electrostatically by both Reynolds stress and a direct ion momentum source, analogous to the concepts of helicity injection and electron momentum input in current drive, respectively. Flow drive by the former does not necessarily require momentum input to the plasma to induce a shear flow. For IBW, the direct ion momentum can be represented by direct electron momentum input, and a charge separation induced stress that imparts little momentum to the plasma. The derived Er profile due to IBW predominantly points inward, with little possibility of direction change, unlike low-frequency Alfvénic RF drive. The profile scale is set by the edge density gradient and electron dissipation. Due to the electrostatic nature of ion Bernstein waves, the poloidal flow contribution dominates in Er. Finally, the necessary edge power absorbed for shear suppression on Princeton Beta Experiment-Modified (PBX-M) [9th Topical Conference on Radio Frequency Power in Plasmas, Charleston, SC, 1991 (American Institute of Physics, New York, 1991), p. 129] is estimated to be 100 kW distributed over 5 cm.

  12. Hvad er tekstfiktion?

    Widell, Peter

    2012-01-01

    artiklen er et bidrag til belysningen af genteori og bygger på ideen om at karakterisere skønlitteratur som et restringeret sæt af universelle tekstparametre. Artiklen fokuserer især på parametren tekstfiktion, hvor jeg forsvarer den position, at en fiktiv tekst hverken kan karakteriseres som en ...... intentioner. Det betyder dog ikke, at sandhed og mening ikke spiller noget rolle ved identifikationen af fiktion, sådan som det hævdes af Walsh og andre....

  13. DEBONDING OF CERAMIC BRACKETS BY ER:YAG LASER

    Fidan ALAKUŞ-SABUNCUOĞLU

    2016-04-01

    Full Text Available Purpose: The objective of the present study is to evaluate the effects of Er:YAG laser debonding of ceramic brackets on the bond strength and the amount of adhesive resin remnant. Materials and Methods: Twenty human mandibular incisors were randomly divided into two groups of 10 and polycrystalline ceramic brackets (Transcend series 6000, 3M Unitek, Monrovia, CA, USA were bonded on enamel surfaces. Group 1 was the control group in which no laser application was performed prior to the shear bond strength (SBS testing. In Group 2, Er:YAG was applied in 3W power for 6 seconds using the scanning method. The brackets were tested for SBS with an Instron universal testing machine and results were expressed in megapascals (MPa. The amount of adhesive remnant was evaluated with Adhesive Remnant Index (ARI. One-way analysis of variance and Tukey’s post-hoc tests were used for statistical analysis. Results: Mean ± standard deviation of SBS values in the control group was 13.42 ±1.23 MPa and 8.47 ±0.71 MPa in the Er:YAG group and this difference was statistically significant (p<0.05. The evaluation of ARI scores demonstrated more adhesive was left on the enamel surface with Er:YAG group. Conclusion: 3W power Er:YAG laser application with the scanning method to polycrystalline ceramic brackets demonstrated lower bond strengths and higher ARI scores during the debonding procedure.

  14. Rouw mag er zijn

    Marlieke Moors

    2015-12-01

    Full Text Available ABSTRACTGrieving is allowedGrief is a human experience. Every form of loss shapes you into the human being you are today. Contrary to what earlier, unproven grief models postulate, grief does not have an end point. That is, bereavement does not have to be completely processed, but it should be integrated into someone’s life. The outdated grief models were often interpreted and used in a normative way, which led to a normative standard model. This portraits the belief that every mourner would experience similar symptoms and would go through a fixed pattern of phases. However, the updated vision emphasizes the individual and unique process of coping with loss: norms concerning grief should be banned. By means of literature research, interviews with professionals and personal experiences, it became clear that finding an equilibrium between restoration-orientated and loss-orientated coping styles is most beneficial. An important aspect in finding this balance is meaningfulness. Furthermore, the ability to bear a loss and to adapt accordingly are important components. Lastly, attaching significance to a loss is a constructive way of integrating the loss into one’s life. The death of a loved one should therefore not be forgotten or tucked away. After all, grief is the price we pay for love. SAMENVATTINGRouw mag er zijnRouw is een menselijke ervaring en elk verlies vormt je als mens. Rouw heeft, in tegenstelling tot wat de verouderde, niet bewezen rouwmodellen beweren, geen eindpunt. Verlies hoeft namelijk niet verwerkt te worden, maar moet juist geïntegreerd worden in iemands leven. De verouderde rouwmodellen zijn vaak normatief opgevat en toegepast, waaruit een normatief standaardmodel is ontstaan. Daarbij werd gedacht dat elke rouwende dezelfde symptomen zou vertonen en het rouwproces volgens vaste fasen zou verlopen. Binnen de vernieuwde visie wordt er juist van uitgegaan dat elk individu een unieke manier van reageren op rouw heeft. Er zou

  15. Han er her endnu

    Bonde, Lisbeth

    2012-01-01

    Interview med den kinesiske aktivist og billedkunstner Ai Weiwei, der sad fængslet i 81 dage i 2011. Hans pas er stadig (i februar 2014) inddraget af myndighederne, så han kan ikke forlade landet, selv om han har betalt en bøde på 13 mio. kr. for ”skatteunddragelse”. Både i sin kunst og i sine...... mange aktioner retter han en hård kritik af det korrupte kinesiske styre, som træder menneskerettighederne under fode. Men uretfærdighedsfølelsen har sin pris i et totalitært og topstyret samfund. Ligegyldigt, hvor mange vigtige udstillinger han har i udlandet, må han blive hjemme og styre aktiviteterne...... via cyberspace. I interviewet fortæller Ai Weiwei om de personlige omkostninger, som hans kamp mod systemet indebærer....

  16. De 9 P’er

    Rennison, Betina Wolfgang

    2017-01-01

    Ledere skal i dag selv skabe deres eget rum til ledelse, men hvad er med til at sætte det, hvilke betingelser og udfordringer er der, og hvordan kan lederne skabe sig selv i et hav af forventninger? Dette katalog inviterer til refleksion herom....

  17. Fremtidens undervisningsmiljøer

    2013-01-01

    Som oplægget til dette temanummer af LOM også indikerede, så sætter vi fokus på fremtidens undervisningsmiljøer på universiteter og UCer. Fremtidens undervisningsmiljøer har mange facetter, hvilket samlingen af artikler også illustrerer. “Fremtidens Undervisningsmiljø” handler om eksisterende erf...

  18. Den rige personlighed er livsduelig

    Holm, Claus

    2015-01-01

    For omtrent 160 år siden formulerede Karl Marx forestillingen om en rig individualitet som det kommunistiske samfunds individideal. I dag får forestillingen relevans. Lyder det lidt besynderligt, er det ikke mærkeligt. For de fleste af os går næppe rundt og tror, at vi er lige på trapperne til...

  19. Humor er en alvorlig sag

    Søltoft, Pia

    2016-01-01

    I modsætning til ironi er humor for Kierkegaard fællesskabsgivende – ironikeren hævder sig selv, men humoristen har sympati med den, man ler med. Humor er hos Kierkegaard udtryk for, at humoristen forliger sig med tilværelsen og dens luner, og dermed grænser humoren hos Kierkegaard op til det...

  20. Brandulykker er et socialt problem

    Leth, Peter Mygind

    1999-01-01

    Det er de gamle, de syge, de handicappede og alkoholikerne, der brænder inde. Typisk har de tabt en cigaret eller tændstik på tøjet. En del af disse brandulykker opstår på plejehjem og andre institutioner, hvor det ofte er plejepersonalet, der opdager og slukker branden....

  1. Shear Elasticity and Shear Viscosity Imaging in Soft Tissue

    Yang, Yiqun

    In this thesis, a new approach is introduced that provides estimates of shear elasticity and shear viscosity using time-domain measurements of shear waves in viscoelastic media. Simulations of shear wave particle displacements induced by an acoustic radiation force are accelerated significantly by a GPU. The acoustic radiation force is first calculated using the fast near field method (FNM) and the angular spectrum approach (ASA). The shear waves induced by the acoustic radiation force are then simulated in elastic and viscoelastic media using Green's functions. A parallel algorithm is developed to perform these calculations on a GPU, where the shear wave particle displacements at different observation points are calculated in parallel. The resulting speed increase enables rapid evaluation of shear waves at discrete points, in 2D planes, and for push beams with different spatial samplings and for different values of the f-number (f/#). The results of these simulations show that push beams with smaller f/# require a higher spatial sampling rate. The significant amount of acceleration achieved by this approach suggests that shear wave simulations with the Green's function approach are ideally suited for high-performance GPUs. Shear wave elasticity imaging determines the mechanical parameters of soft tissue by analyzing measured shear waves induced by an acoustic radiation force. To estimate the shear elasticity value, the widely used time-of-flight method calculates the correlation between shear wave particle velocities at adjacent lateral observation points. Although this method provides accurate estimates of the shear elasticity in purely elastic media, our experience suggests that the time-of-flight (TOF) method consistently overestimates the shear elasticity values in viscoelastic media because the combined effects of diffraction, attenuation, and dispersion are not considered. To address this problem, we have developed an approach that directly accounts for all

  2. Temperature Effects of Dielectric Properties of ER Fluids

    Qiu, Z. Y.; Hu, L.; Liu, M. W.; Bao, H. X.; Jiang, Y. G.; Zhou, L. W.; Tang, Y.; Gao, Z.; Sun, M.; Korobko, E. V.

    Under the consideration of the role that energy transfer and dissipation play in ER effect, an improved theory frame for ER effects, polarization-dissipation-structure-rheology, is suggested. The theory frame is substantiated by the basic physical laws and certain critical experimental facts. The dielectric response of a diatomite ER fluid to temperature is measured in the temperature range of 140 K to 400 K. By comparison of the DC conductivity with the AC effective conductivity of the sample, we found that the AC dielectric loss consists of two parts. One part comes from the DC conductivity, the other from the response of the bound charges in scope of particle to AC field. It is suggested that the response of bound charges is very important to ER effects. Besides, the effect of temperature on shear stress is measured, and interpreted based on the dielectric measurements. The source of two loss peaks in the curve of the dielectric loss versus temperature is not clear.

  3. Min mentor er min voksenven

    Kaiser, Birte

    2009-01-01

    En artikel i bogen: 6 belysninger af vejledning, brydninger, forståelser & praksis. Artiklen er et sammendrag af en diskursanalyse fra 2008 fra projetrapporten: Ind under huden, www.vejledning.net...

  4. Forenklingens fire F'er

    Bentzen, Tina Øllgaard

    2017-01-01

    At fjerne styring er det, man ofte forbinder med afbureaukratisering, men det er ikke tilstrækkeligt, når man vil gå fra flotte ambitioner til en styring, som reelt opleves enklere. For at forenkle må man også forandre, forankre og fastholde styring, og det må ske i et samspil mellem de aktører, ...

  5. Effects of ExB velocity shear and magnetic shear on turbulence and transport in magnetic confinement devices

    Burrell, K.H.

    1996-11-01

    One of the scientific success stories of fusion research over the past decade is the development of the ExB shear stabilization model to explain the formation of transport barriers in magnetic confinement devices. This model was originally developed to explain the transport barrier formed at the plasma edge in tokamaks after the L (low) to H (high) transition. This concept has the universality needed to explain the edge transport barriers seen in limiter and divertor tokamaks, stellarators, and mirror machines. More recently, this model has been applied to explain the further confinement improvement from H (high)-mode to VH (very high)-mode seen in some tokamaks, where the edge transport barrier becomes wider. Most recently, this paradigm has been applied to the core transport barriers formed in plasmas with negative or low magnetic shear in the plasma core. These examples of confinement improvement are of considerable physical interest; it is not often that a system self-organizes to a higher energy state with reduced turbulence and transport when an additional source of free energy is applied to it. The transport decrease that is associated with ExB velocity shear effects also has significant practical consequences for fusion research. The fundamental physics involved in transport reduction is the effect of ExB shear on the growth, radial extent and phase correlation of turbulent eddies in the plasma. The same fundamental transport reduction process can be operational in various portions of the plasma because there are a number ways to change the radial electric field Er. An important theme in this area is the synergistic effect of ExB velocity shear and magnetic shear. Although the ExB velocity shear appears to have an effect on broader classes of microturbulence, magnetic shear can mitigate some potentially harmful effects of ExB velocity shear and facilitate turbulence stabilization

  6. Nonlinear Simulations of Trapped Electron Mode Turbulence in Low Magnetic Shear Stellarators

    Faber, B. J.; Pueschel, M. J.; Terry, P. W.; Hegna, C. C.

    2017-10-01

    Optimized stellarators, like the Helically Symmetric eXperiment (HSX), often operate with small global magnetic shear to avoid low-order rational surfaces and magnetic islands. Nonlinear, flux-tube gyrokinetic simulations of density-gradient-driven Trapped Electron Mode (TEM) turbulence in HSX shows two distinct spectral fluctuation regions: long-wavelength slab-like TEMs localized by global magnetic shear that extend along field lines and short-wavelength TEMs localized by local magnetic shear to a single helical bad curvature region. The slab-like TEMs require computational domains significantly larger than one poloidal turn and are computationally expensive, making turbulent optimization studies challenging. A computationally more efficient, zero-average-magnetic-shear approximation is shown to sufficiently describe the relevant nonlinear physics and replicate finite-shear computations, and can be exploited in quasilinear models based on linear gyrokinetics as a feasible optimization tool. TEM quasilinear heat fluxes are computed with the zero-shear approximation and compared to experimentally-relevant nonlinear gyrokinetic TEM heat fluxes for HSX. Research supported by U.S. DoE Grants DE-FG02-99ER54546, DE-FG02-93ER54222 and DE-FG02-89ER53291.

  7. Proceedings of the International Conference on Electrorheological Fluids (4th) Held in Feldkirch (Austria) on 20-23 July 1993

    1994-01-01

    important to use a high-resolution rheometer for detailed examination of the response of ER fluids. We exam ~ned the difference between data obtained...ERZ researc fC1 ro m its itmcv1ikth1l -14 Exam pl.’ olt these devicesý inchltde autoomtmive shock tthSorberie’" and cnigtte n~ionts𔃿 1-1,tNever...Differential Tranrsfuriner [LVUTI Torsjui Elemien~t Mouningi~ Ltam ;p Lonner i un Figur-e 7: Cross-sectional view ot Lhe insulated IIAAKE. CV 20 iiiewaeniucnet

  8. Keyed shear joints

    Hansen, Klaus

    This report gives a summary of the present information on the behaviour of vertical keyed shear joints in large panel structures. An attemp is made to outline the implications which this information might have on the analysis and design of a complete wall. The publications also gives a short...

  9. Sheared Electroconvective Instability

    Kwak, Rhokyun; Pham, Van Sang; Lim, Kiang Meng; Han, Jongyoon

    2012-11-01

    Recently, ion concentration polarization (ICP) and related phenomena draw attention from physicists, due to its importance in understanding electrochemical systems. Researchers have been actively studying, but the complexity of this multiscale, multiphysics phenomenon has been limitation for gaining a detailed picture. Here, we consider electroconvective(EC) instability initiated by ICP under pressure-driven flow, a scenario often found in electrochemical desalinations. Combining scaling analysis, experiment, and numerical modeling, we reveal unique behaviors of sheared EC: unidirectional vortex structures, its size selection and vortex propagation. Selected by balancing the external pressure gradient and the electric body force, which generates Hagen-Poiseuille(HP) flow and vortical EC, the dimensionless EC thickness scales as (φ2 /UHP)1/3. The pressure-driven flow(or shear) suppresses unfavorably-directed vortices, and simultaneously pushes favorably-directed vortices with constant speed, which is linearly proportional to the total shear of HP flow. This is the first systematic characterization of sheared EC, which has significant implications on the optimization of electrodialysis and other electrochemical systems.

  10. An underwater shear compactor

    Biver, E.; Sims, J.

    1997-01-01

    This paper, originally presented at the WM'96 Conference in Tucson Arizona, describes a concept of a specialised decommissioning tool designed to operate underwater and to reduce the volume of radioactive components by shearing and compacting. The shear compactor was originally conceived to manage the size reduction of a variety of decommissioned stainless steel tubes stored within a reactor fuel cooling pond and which were consuming a substantial volume of the pond. The main objective of this tool was to cut the long tubes into shorter lengths and to compact them into a flat rectangular form which could be stacked on the pond floor, thus saving valuable space. The development programme, undertaken on this project, investigated a wide range of factors which could contribute to an extended cutting blade performance, ie: materials of construction, cutting blade shape and cutting loads required, shock effects, etc. The second phase was to review other aspects of the design, such as radiological protection, cutting blade replacement, maintenance, pond installation and resultant wall loads, water hydraulics, collection of products of shearing/compacting operations, corrosion of the equipment, control system, operational safety and the ability of the equipment to operate in dry environments. The paper summarises the extended work programme involved with this shear compactor tool. (author)

  11. Combination of spaceborne radar interferometry (DEM) and Landsat TM imageries contributing to recent tectonic and geology studies in the Aswa lineament shear zone (Sudan)

    Kervyn, V.C.; Slob, S.; Derauw, D.; Cecchi, Giovanna; Zilioli, Eugenio

    1998-01-01

    Until recently, the Aswa lineament shear zone in Uganda and Sudan was considered to be tectonically at rest but the 1990- 1991 seismic events triggered a renewal of interest in this area. Using ERS1 - ERS2 tandem covering the area where earthquakes were observed, we have generated a high resolution

  12. Shear strength of non-shear reinforced concrete elements

    Hoang, Cao linh

    1997-01-01

    The paper deals with the plastic shear strength of non shear reinforced T-beams.The influence of an un-reinforced flange on the shear capacity is investigated by considering a failure mechanism involving crack sliding in the web and a kind of membrane action over an effective width of the flange...

  13. Experiments on sheet metal shearing

    Gustafsson, Emil

    2013-01-01

    Within the sheet metal industry, different shear cutting technologies are commonly used in several processing steps, e.g. in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material.Numerical models to predict forces and sheared edge geometry for different sheet metal grades and different shear parameter set-ups a...

  14. CAT LIDAR wind shear studies

    Goff, R. W.

    1978-01-01

    The studies considered the major meteorological factors producing wind shear, methods to define and classify wind shear in terms significant from an aircraft perturbation standpoint, the significance of sensor location and scan geometry on the detection and measurement of wind shear, and the tradeoffs involved in sensor performance such as range/velocity resolution, update frequency and data averaging interval.

  15. Hvis en kartoffel er forkert, hvad er en Mars-bar så?

    Lichtenstein, Mia Beck; Thomsen, Freja; Hinze, Cecilie

    2016-01-01

    Danske unge er de slankeste af 41 europæiske unge, men de føler sig ofte tykke og går på slankekur. Hvad er årsagen, og hvorfor er det et problem?......Danske unge er de slankeste af 41 europæiske unge, men de føler sig ofte tykke og går på slankekur. Hvad er årsagen, og hvorfor er det et problem?...

  16. Den sproglige leg er super fly

    Just, Sine Nørholm

    2013-01-01

    Man kan rappe om alt. I hvert fald hvis man er Marvelous Mosell. I spændingsfeltet mellem fiktion og virkelighed skaber Mosell sin persona i et forjættende 80' er-univers der på en og samme tid er vildt overdrevet og helt autentisk.......Man kan rappe om alt. I hvert fald hvis man er Marvelous Mosell. I spændingsfeltet mellem fiktion og virkelighed skaber Mosell sin persona i et forjættende 80' er-univers der på en og samme tid er vildt overdrevet og helt autentisk....

  17. Gelation under shear

    Butler, B.D.; Hanley, H.J.M.; Straty, G.C. [National Institute of Standards and Technology, Boulder, CO (United States); Muzny, C.D. [Univ. of Colorado, Boulder, CO (United States)

    1995-12-31

    An experimental small angle neutron scattering (SANS) study of dense silica gels, prepared from suspensions of 24 nm colloidal silica particles at several volume fractions {theta} is discussed. Provided that {theta}{approx_lt}0.18, the scattered intensity at small wave vectors q increases as the gelation proceeds, and the structure factor S(q, t {yields} {infinity}) of the gel exhibits apparent power law behavior. Power law behavior is also observed, even for samples with {theta}>0.18, when the gel is formed under an applied shear. Shear also enhances the diffraction maximum corresponding to the inter-particle contact distance of the gel. Difficulties encountered when trying to interpret SANS data from these dense systems are outlined. Results of computer simulations intended to mimic gel formation, including computations of S(q, t), are discussed. Comments on a method to extract a fractal dimension characterizing the gel are included.

  18. N-ov-emb-er

    " to. Andrew Z Fire - Stanford University School of Medicine Stanford, CA, USA. Craig C Mello - University of Massachusetts Medical School Worcester, MA, USA. -96----------------------------~~--------R-ES-O-N-A-N-C-E--1 -N-ov-e-m-b-er--2-oo-6.

  19. Hvad er ledelse af brugerinddragelse?

    Holm-Petersen, Christina; Navne, Laura Emdal

    2015-01-01

    Brugerinddragelse i det danske sundhedsvæsen står højt på den politiske dagsorden, men det er stadig en udfordring at implementere visionen i klinisk praksis. Ledelse af brugerinddragelse bliver aktuelt udpeget som en central nøgle til at føre visionen ud i livet. Samtidig er der kun relativt lidt......, at brugerinddragelse skal implementeres i en verden, hvor der allerede er en række andre mål tilstede. En central ledelsesudfordring er derfor, at nogle af målene med brugerinddragelse forudsætter nye måder at organisere ikke bare arbejdet og kompetencer på, men også relationer til patienter og pårørende. En væsentlig...... that organize relations Patient involvement in the health services in Denmark is high on the political agenda, though continues to be a challenge to implement. It is increasingly said that leadership is crucial to the implementation process. However, research into the role of leaders in patient involvement...

  20. Shear Roll Mill Reactivation

    2012-09-13

    pneumatically operated paste dumper and belt conveyor system, the loss in weight feeder system, the hydraulically operated shear roll mill, the pellet...out feed belt conveyor , and the pack out system comprised of the metal detector, scale, and pack out empty and full drum roller conveyors . Page | 4...feed hopper and conveyor supplying the loss in weight feeder were turned on, and it was verified that these items functioned as designed . The

  1. Local transport barrier formation and relaxation in reverse-shear plasmas on the TFTR tokamak

    Synakowski, E.J.; Beer, M.A.

    1997-02-01

    The roles of turbulence stabilization by sheared E x B flow and Shafranov-shift gradients are examined for TFTR. Enhanced Reverse-Shear plasmas. Both effects in combination provide the basis of a positive-feedback model that predicts reinforced turbulence suppression with increasing pressure gradient. Local fluctuation behavior at the onset of ERS confinement is consistent with this framework. The power required for transitions into the ERS regime are lower when high power neutral beams are applied earlier in the current profile evolution, consistent with the suggestion that both effects play a role. Separation of the roles of E x B and Shafranov shift effects was performed by varying the E x B shear through changes in the toroidal velocity with nearly-steady-state pressure profiles. Transport and fluctuation levels increase only when E x B shearing rates are driven below a critical value that is comparable to the fastest linear growth rates of the dominant instabilities. While a turbulence suppression criterion that involves the ratio of shearing to linear growth rates is in accord with many of these results, the existence of hidden dependencies of the criterion is suggested in experiments where the toroidal field was varied. The forward transition into the ERS regime has also been examined in strongly rotating plasmas. The power threshold is higher with unidirectional injection than with balanced injection

  2. Plasticity Approach to Shear Design

    Hoang, Cao Linh; Nielsen, Mogens Peter

    1998-01-01

    The paper presents some plastic models for shear design of reinforced concrete beams. Distinction is made between two shear failure modes, namely web crushing and crack sliding. The first mentioned mode is met in beams with large shear reinforcement degrees. The mode of crack sliding is met in non......-shear reinforced beams as well as in lightly shear reinforced beams. For such beams the shear strength is determined by the recently developed crack sliding model. This model is based upon the hypothesis that cracks can be transformed into yield lines, which have lower sliding resistance than yield lines formed...... in uncracked concrete. Good agree between theory and tests has been found.Keywords: dsign, plasticity, reinforced concrete, reinforcement, shear, web crushing....

  3. ER2OWL: Generating OWL Ontology from ER Diagram

    Fahad, Muhammad

    Ontology is the fundamental part of Semantic Web. The goal of W3C is to bring the web into (its full potential) a semantic web with reusing previous systems and artifacts. Most legacy systems have been documented in structural analysis and structured design (SASD), especially in simple or Extended ER Diagram (ERD). Such systems need up-gradation to become the part of semantic web. In this paper, we present ERD to OWL-DL ontology transformation rules at concrete level. These rules facilitate an easy and understandable transformation from ERD to OWL. The set of rules for transformation is tested on a structured analysis and design example. The framework provides OWL ontology for semantic web fundamental. This framework helps software engineers in upgrading the structured analysis and design artifact ERD, to components of semantic web. Moreover our transformation tool, ER2OWL, reduces the cost and time for building OWL ontologies with the reuse of existing entity relationship models.

  4. Endoplasmic Reticulum (ER Stress and Endocrine Disorders

    Daisuke Ariyasu

    2017-02-01

    Full Text Available The endoplasmic reticulum (ER is the organelle where secretory and membrane proteins are synthesized and folded. Unfolded proteins that are retained within the ER can cause ER stress. Eukaryotic cells have a defense system called the “unfolded protein response” (UPR, which protects cells from ER stress. Cells undergo apoptosis when ER stress exceeds the capacity of the UPR, which has been revealed to cause human diseases. Although neurodegenerative diseases are well-known ER stress-related diseases, it has been discovered that endocrine diseases are also related to ER stress. In this review, we focus on ER stress-related human endocrine disorders. In addition to diabetes mellitus, which is well characterized, several relatively rare genetic disorders such as familial neurohypophyseal diabetes insipidus (FNDI, Wolfram syndrome, and isolated growth hormone deficiency type II (IGHD2 are discussed in this article.

  5. Endoplasmic Reticulum (ER) Stress and Endocrine Disorders

    Ariyasu, Daisuke; Yoshida, Hiderou; Hasegawa, Yukihiro

    2017-01-01

    The endoplasmic reticulum (ER) is the organelle where secretory and membrane proteins are synthesized and folded. Unfolded proteins that are retained within the ER can cause ER stress. Eukaryotic cells have a defense system called the “unfolded protein response” (UPR), which protects cells from ER stress. Cells undergo apoptosis when ER stress exceeds the capacity of the UPR, which has been revealed to cause human diseases. Although neurodegenerative diseases are well-known ER stress-related diseases, it has been discovered that endocrine diseases are also related to ER stress. In this review, we focus on ER stress-related human endocrine disorders. In addition to diabetes mellitus, which is well characterized, several relatively rare genetic disorders such as familial neurohypophyseal diabetes insipidus (FNDI), Wolfram syndrome, and isolated growth hormone deficiency type II (IGHD2) are discussed in this article. PMID:28208663

  6. Hvornår er man ung?

    Gundelach, Peter; Nørregård-Nielsen, Esther C.

    2002-01-01

    Hvornår er man ung, og hvornår er man voksen? Er der forskelle i befolkningens værdier i forhold til arbejde og politik, når det undersøges ud fra henholdsvis et alders- eller generationsperspektiv? Baseret på data fra den danske del af den internationale værdiundersøgelse vises at der er så store...

  7. Shear Resistance Variations in Experimentally Sheared Mudstone Granules: A Possible Shear-Thinning and Thixotropic Mechanism

    Hu, Wei; Xu, Qiang; Wang, Gonghui; Scaringi, Gianvito; Mcsaveney, Mauri; Hicher, Pierre-Yves

    2017-11-01

    We present results of ring shear frictional resistance for mudstone granules of different size obtained from a landslide shear zone. Little rate dependency of shear resistance was observed in sand-sized granules in any wet or dry test, while saturated gravel-sized granules exhibited significant and abrupt reversible rate-weakening (from μ = 0.6 to 0.05) at about 2 mm/s. Repeating resistance variations occurred also under constant shear displacement rate. Mudstone granules generate mud as they are crushed and softened. Shear-thinning and thixotropic behavior of the mud can explain the observed behavior: with the viscosity decreasing, the mud can flow through the coarser soil pores and migrate out from the shear zone. This brings new granules into contact which produces new mud. Thus, the process can start over. Similarities between experimental shear zones and those of some landslides in mudstone suggest that the observed behavior may play a role in some landslide kinematics.

  8. Hvorfor er sygeplejersker usynlige i offentlige medier?

    Joensen, Annemi Lund; Hall, Elisabeth

    2015-01-01

    Når der er sygeplejerelevante emner til debat i de offentlige medier på Færøerne, bærer debatten præg af sygeplejerskers manglende deltagelse. Sygeplejerskerne er usynlige. Et eksempel på dette er en debat om besparelser inden for ældreomsorgen. Til trods for at besparelsen fik omfattende konsekv...

  9. Shear-induced chaos

    Lin, Kevin K; Young, Lai-Sang

    2008-01-01

    Guided by a geometric understanding developed in earlier works of Wang and Young, we carry out numerical studies of shear-induced chaos in several parallel but different situations. The settings considered include periodic kicking of limit cycles, random kicks at Poisson times and continuous-time driving by white noise. The forcing of a quasi-periodic model describing two coupled oscillators is also investigated. In all cases, positive Lyapunov exponents are found in suitable parameter ranges when the forcing is suitably directed

  10. Shear-induced chaos

    Lin, Kevin K.; Young, Lai-Sang

    2008-05-01

    Guided by a geometric understanding developed in earlier works of Wang and Young, we carry out numerical studies of shear-induced chaos in several parallel but different situations. The settings considered include periodic kicking of limit cycles, random kicks at Poisson times and continuous-time driving by white noise. The forcing of a quasi-periodic model describing two coupled oscillators is also investigated. In all cases, positive Lyapunov exponents are found in suitable parameter ranges when the forcing is suitably directed.

  11. Bolt Shear Force Sensor

    2015-03-12

    0030] FIG. 7 is an isometric view of a deformable ring of the bolt shear force sensor of the present invention with an optical Attorney Docket No...102587 9 of 19 fiber having Bragg gratings wound around the ring; [0031] FIG. 8 is an isometric view of the deformable ring with wire strain... strength . [0047] Once the joint is subjected to an external load (see force arrows “F” and “F/2”); any frictional resistance to slip is overcome and

  12. Jordkvalitetskriterier for PAH'er

    Carlsen, Lars

    2009-01-01

    For to år siden forhøjede Miljøstyrelsen den administrativt fastsatte grænseværdi for polycycliske hydrocarboner (PAH’er) i jord med en faktor 3, hvilket i praksis betød at en række grunde, der tidligere var klassifi ceret som forurenede, nu ikke klassifi ceres sådan. Den hidtidige og den nye met...

  13. Effect of Er:YAG Laser and Sandblasting in Recycling of Ceramic Brackets.

    Yassaei, Soghra; Aghili, Hossein; Hosseinzadeh Firouzabadi, Azadeh; Meshkani, Hamidreza

    2017-01-01

    Introduction: This study was performed to determine the shear bond strength of rebonded mechanically retentive ceramic brackets after recycling with Erbium-Doped Yttrium Aluminum Garnet (Er:YAG) laser or sandblasting. Methods: Twenty-eight debonded ceramic brackets plus 14 intact new ceramic brackets were used in this study. Debonded brackets were randomly divided into 2 groups of 14. One group was treated by Er:YAG laser and the other with sandblasting. All the specimens were randomly bonded to 42 intact human upper premolars. The shear bond strength of all specimens was determined with a universal testing machine at a crosshead speed of 0.5 mm/min until bond failure occurred. The recycled bracket base surfaces were observed under a scanning electron microscope (SEM). Analysis of variance (ANOVA) and Tukey tests were used to compare the shear bond strength of the 3 groups. Fisher exact test was used to evaluate the differences in adhesive remnant index (ARI) scores. Results: The highest bond strength belonged to brackets recycled by Sandblasting (16.83 MPa). There was no significant difference between the shear bond strength of laser and control groups. SEM photographs showed differences in 2 recycling methods. The laser recycled bracket appeared to have as well-cleaned base as the new bracket. Although the sandblasted bracket photographs showed no remnant adhesives, remarkable micro-roughening of the base of the bracket was apparent. Conclusion: According to the results of this study, both Er:YAG laser and sandblasting were efficient to mechanically recondition retentive ceramic brackets. Also, Er:YAG laser did not change the design of bracket base while removing the remnant adhesives which might encourage its application in clinical practice.

  14. Viscous properties of aluminum oxide nanotubes and aluminium oxide nanoparticles - silicone oil suspensions

    Thapa, Ram; French, Steven; Delgado, Adrian; Ramos, Carlos; Gutierrez, Jose; Chipara, Mircea; Lozano, Karen

    2010-03-01

    Electrorheological (ER) fluids consisting of γ-aluminum oxide nanotubes and γ-aluminum oxide nanoparticles dispersed within silicone oil were prepared. The relationship between shear stress and shear rate was measured and theoretically simulated by using an extended Bingham model for both the rheological and electrorheological features of these systems. Shear stress and viscosity showed a sharp increase for the aluminum oxide nanotubes suspensions subjected to applied electric fields whereas aluminum oxide nanoparticles suspensions showed a moderate change. It was found that the transition from liquid to solid state (mediated by the applied electric field) can be described by a power law and that for low applied voltages the relationship is almost linear.

  15. Effect of Er:YAG laser irradiation on bonding property of zirconia ceramics to resin cement.

    Lin, Yihua; Song, Xiaomeng; Chen, Yaming; Zhu, Qingping; Zhang, Wei

    2013-12-01

    This study aimed to investigate whether or not an erbium: yttrium-aluminum-garnet (Er:YAG) laser could improve the bonding property of zirconia ceramics to resin cement. Surface treatments can improve the bonding properties of dental ceramics. However, little is known about the effect of Er:YAG laser irradiated on zirconia ceramics. Specimens of zirconia ceramic pieces were made, and randomly divided into 11 groups according to surface treatments, including one control group (no treatment), one air abrasion group, and nine Er:YAG laser groups. The laser groups were subdivided by applying different energy intensities (100, 200, or 300 mJ) and irradiation times (5, 10, or 15 sec). After surface treatments, ceramic pieces had their surface morphology observed, and their surface roughness was measured. All specimens were bonded to resin cement. Shear bond strength was measured after the bonded specimens were stored in water for 24 h, and additionally aged by thermocycling. Statistical analyses were performed using one way analysis of variance (ANOVA) and Tukey's test for shear bond strength, and Dunnett's t test for surface roughness, with α=0.05. Er:YAG laser irradiation changed the morphological characteristics of zirconia ceramics. Higher energy intensities (200, 300 mJ) could roughen the ceramics, but also caused surface cracks. There were no significant differences in the bond strength between the control group and the laser groups treated with different energy intensities or irradiation times. Air abrasion with alumina particles induced highest surface roughness and shear bond strength. Er:YAG laser irradiation cannot improve the bonding property of zirconia ceramics to resin cement. Enhancing irradiation intensities and extending irradiation time have no benefit on the bond of the ceramics, and might cause material defect.

  16. Excited waves in shear layers

    Bechert, D. W.

    1982-01-01

    The generation of instability waves in free shear layers is investigated. The model assumes an infinitesimally thin shear layer shed from a semi-infinite plate which is exposed to sound excitation. The acoustical shear layer excitation by a source further away from the plate edge in the downstream direction is very weak while upstream from the plate edge the excitation is relatively efficient. A special solution is given for the source at the plate edge. The theory is then extended to two streams on both sides of the shear layer having different velocities and densities. Furthermore, the excitation of a shear layer in a channel is calculated. A reference quantity is found for the magnitude of the excited instability waves. For a comparison with measurements, numerical computations of the velocity field outside the shear layer were carried out.

  17. Designing shear-thinning

    Nelson, Arif Z.; Ewoldt, Randy H.

    2017-11-01

    Design in fluid mechanics often focuses on optimizing geometry (airfoils, surface textures, microfluid channels), but here we focus on designing fluids themselves. The dramatically shear-thinning ``yield-stress fluid'' is currently the most utilized non-Newtonian fluid phenomenon. These rheologically complex materials, which undergo a reversible transition from solid-like to liquid-like fluid flow, are utilized in pedestrian products such as paint and toothpaste, but also in emerging applications like direct-write 3D printing. We present a paradigm for yield-stress fluid design that considers constitutive model representation, material property databases, available predictive scaling laws, and the many ways to achieve a yield stress fluid, flipping the typical structure-to-rheology analysis to become the inverse: rheology-to-structure with multiple possible materials as solutions. We describe case studies of 3D printing inks and other flow scenarios where designed shear-thinning enables performance remarkably beyond that of Newtonian fluids. This work was supported by Wm. Wrigley Jr. Company and the National Science Foundation under Grant No. CMMI-1463203.

  18. Inductive shearing of drilling pipe

    Ludtka, Gerard M.; Wilgen, John; Kisner, Roger; Mcintyre, Timothy

    2016-04-19

    Induction shearing may be used to cut a drillpipe at an undersea well. Electromagnetic rings may be built into a blow-out preventer (BOP) at the seafloor. The electromagnetic rings create a magnetic field through the drillpipe and may transfer sufficient energy to change the state of the metal drillpipe to shear the drillpipe. After shearing the drillpipe, the drillpipe may be sealed to prevent further leakage of well contents.

  19. Er,Cr:YSGG Laser as a Novel Method for Rebonding Failed Ceramic Brackets.

    Sohrabi, Aydin; Jafari, Sanaz; Kimyai, Soodabeh; Rikhtehgaran, Sahand

    2016-10-01

    Since there is no standard method for rebonding loose ceramic brackets, the aim of this study was to evaluate the possibility of using Er,Cr:YSGG laser to eliminate the remaining composite materials from the base of ceramic brackets and to compare the bond strength of rebonded brackets with the new ones. Sixty-two extracted human premolars were mounted in acrylic cylinders. Thirty-one ceramic brackets were bonded, and shear bond strength was tested using Hounsfield testing machine. The remnants of the bonding material were removed from the bases of brackets using Er,Cr:YSGG laser. These brackets were rebonded to 31 fresh teeth and again shear bond strength was measured. Pattern of debonding was assessed in both cases under a stereomicroscope and graded according to ARI index. Data were analyzed with independent t-test and Fisher's exact test. Mean shear bond strength of the bond and rebond groups was 12.29 ± 5.46 and 10.58 ± 5.16 MPa, respectively. There were no significant differences between the two groups (p = 0.21). Pattern of bond failure was not statistically different between the two groups. Er,Cr:YSGG laser was effective in removing the remnants of bonding material from the base of ceramic brackets without any interference with the ceramic base itself, demonstrating that it might be a suitable method for rebonding ceramic brackets.

  20. Magnetorheological dampers in shear mode

    Wereley, N M; Cho, J U; Choi, Y T; Choi, S B

    2008-01-01

    In this study, three types of shear mode damper using magnetorheological (MR) fluids are theoretically analyzed: linear, rotary drum, and rotary disk dampers. The damping performance of these shear mode MR dampers is characterized in terms of the damping coefficient, which is the ratio of the equivalent viscous damping at field-on status to the damping at field-off status. For these three types of shear mode MR damper, the damping coefficient or dynamic range is derived using three different constitutive models: the Bingham–plastic, biviscous, and Herschel–Bulkley models. The impact of constitutive behavior on shear mode MR dampers is theoretically presented and compared

  1. Direct evidence of stationary zonal flows and critical gradient behavior for Er during formation of the edge pedestal in JET

    Hillesheim, Jon

    2015-11-01

    High spatial resolution measurements with Doppler backscattering in JET have provided new insights into the development of the edge radial electric field during pedestal formation. The characteristics of Er have been studied as a function of density at 2.5 MA plasma current and 3 T toroidal magnetic field. We observe fine-scale spatial structure in the edge Er well prior to the LH transition, consistent with stationary zonal flows. Zonal flows are a fundamental mechanism for the saturation of turbulence and this is the first direct evidence of stationary zonal flows in a tokamak. The radial wavelength of the zonal flows systematically decreases with density. The zonal flows are clearest in Ohmic conditions, weaker in L-mode, and absent in H-mode. Measurements also show that after neutral beam heating is applied, the edge Er builds up at a constant gradient into the core during L-mode, at radii where Er is mainly due to toroidal velocity. The local stability of velocity shear driven turbulence, such as the parallel velocity gradient mode, will be assessed with gyrokinetic simulations. This critical Er shear persists across the LH transition into H-mode. Surprisingly, a reduction in the apparent magnitude of the Er well depth is observed directly following the LH transition at high densities. Establishing the physics basis for the LH transition is important for projecting scalings to ITER and these observations challenge existing models based on increased Er shear or strong zonal flows as the trigger for the transition. This work has been carried out within the framework of the EUROfusion Consortium and has received funding from the Euratom research and training programme 2014-2018 under grant agreement No 633053. The views and opinions expressed herein do not necessarily reflect those of the European Commission.

  2. Shear strength of non-shear reinforced concrete elements

    Hoang, Cao linh

    1997-01-01

    The paper deals with the shear strength of prestressed hollow-core slabs determined by the theory of plasticity. Two failure mechanisms are considered in order to derive the solutions.In the case of sliding failure in a diagonal crack, the shear strength is determined by means of the crack sliding...

  3. Extended theory of main ion and impurity rotation and bootstrap current in a shear layer

    Kim, Y.B.; Hinton, F.L.; St. John, H.; Taylor, T.S.; Wroblewski, D.

    1993-11-01

    In this paper, standard neoclassical theory has been extended into the shear layer. Main ion and impurity ion rotation velocity and bootstrap current within shear layer in H-mode are discussed. Inside the H-mode shear layer, standard neoclassical theory is not valid since the ion poloidal gyroradius becomes comparable to pressure gradient and electric field gradient scale length. To allow for arbitrary ratio of ρθi/L n and ρθi/L Er a new kinetic theory of main ion species within electric field shear layer has been developed with the assumption that ρθi/R o is still small. As a consequence, both impurity flows and bootstrap current have to be modified. We present modified expressions of impurity flows and bootstrap current are presented neglecting ion temperature gradient. Comparisons with DIII-D measurements are also discussed

  4. A Piezoelectric Shear Stress Sensor

    Kim, Taeyang; Saini, Aditya; Kim, Jinwook; Gopalarathnam, Ashok; Zhu, Yong; Palmieri, Frank L.; Wohl, Christopher J.; Jiang, Xiaoning

    2016-01-01

    In this paper, a piezoelectric sensor with a floating element was developed for shear stress measurement. The piezoelectric sensor was designed to detect the pure shear stress suppressing effects of normal stress generated from the vortex lift-up by applying opposite poling vectors to the: piezoelectric elements. The sensor was first calibrated in the lab by applying shear forces and it showed high sensitivity to shear stress (=91.3 +/- 2.1 pC/Pa) due to the high piezoelectric coefficients of PMN-33%PT (d31=-1330 pC/N). The sensor also showed almost no sensitivity to normal stress (less than 1.2 pC/Pa) because of the electromechanical symmetry of the device. The usable frequency range of the sensor is 0-800 Hz. Keywords: Piezoelectric sensor, shear stress, floating element, electromechanical symmetry

  5. ER Stress and Lipid Metabolism in Adipocytes

    Beth S. Zha

    2012-01-01

    Full Text Available The role of endoplasmic reticulum (ER stress is a rapidly emerging field of interest in the pathogenesis of metabolic diseases. Recent studies have shown that chronic activation of ER stress is closely linked to dysregulation of lipid metabolism in several metabolically important cells including hepatocytes, macrophages, β-cells, and adipocytes. Adipocytes are one of the major cell types involved in the pathogenesis of the metabolic syndrome. Recent advances in dissecting the cellular and molecular mechanisms involved in the regulation of adipogenesis and lipid metabolism indicate that activation of ER stress plays a central role in regulating adipocyte function. In this paper, we discuss the current understanding of the potential role of ER stress in lipid metabolism in adipocytes. In addition, we touch upon the interaction of ER stress and autophagy as well as inflammation. Inhibition of ER stress has the potential of decreasing the pathology in adipose tissue that is seen with energy overbalance.

  6. Endoplasmic reticulum: ER stress regulates mitochondrial bioenergetics

    Bravo, Roberto; Gutierrez, Tomás; Paredes, Felipe; Gatica, Damián; Rodriguez, Andrea E.; Pedrozo, Zully; Chiong, Mario; Parra, Valentina; Quest, Andrew F.G.; Rothermel, Beverly A.; Lavandero, Sergio

    2014-01-01

    Endoplasmic reticulum (ER) stress activates an adaptive unfolded protein response (UPR) that facilitates cellular repair, however, under prolonged ER stress, the UPR can ultimately trigger apoptosis thereby terminating damaged cells. The molecular mechanisms responsible for execution of the cell death program are relatively well characterized, but the metabolic events taking place during the adaptive phase of ER stress remain largely undefined. Here we discuss emerging evidence regarding the metabolic changes that occur during the onset of ER stress and how ER influences mitochondrial function through mechanisms involving calcium transfer, thereby facilitating cellular adaptation. Finally, we highlight how dysregulation of ER–mitochondrial calcium homeostasis during prolonged ER stress is emerging as a novel mechanism implicated in the onset of metabolic disorders. PMID:22064245

  7. Optimal fodring af goldkøer

    Bjerre-Harpøth, Vibeke; Damgaard, Birthe Marie

    2013-01-01

    Et forsøg har vist, at køer på lavt energiniveau i goldperioden var fysiologisk sundere og havde mindre risiko for at udvikle stofskiftesygdomme end køer på et højt energiniveau. Forsøget viste også, at køer på et normalt energiniveau i senlaktationen gav mere mælk i den efterfølgende laktation e...

  8. Er moral bare noget vi leger?

    Thomsen, Frej Klem

    2014-01-01

    Hvis man er skeptiker, så er moral nemlig altid kun et udtryk for psykologi og kultur, også når det handler om for eksempel misbrug af børn i Tønder-sagen eller terror-angreb i Madrid, London og Mumbai .......Hvis man er skeptiker, så er moral nemlig altid kun et udtryk for psykologi og kultur, også når det handler om for eksempel misbrug af børn i Tønder-sagen eller terror-angreb i Madrid, London og Mumbai ....

  9. Thermodynamic assessments of the Ag-Er and Er-Y systems

    Wang, S.L.; Wang, C.P.; Liu, X.J.; Tang, A.T.; Pan, F.S.; Ishida, K.

    2010-01-01

    The phase diagrams and thermodynamic properties in the Ag-Er and Er-Y binary systems have been assessed by using the CALPHAD (Calculation of Phase Diagrams) method on the basis of the experimental data including the thermodynamic properties and phase equilibria. The Gibbs free energies of the liquid, bcc, fcc, and hcp phases were described by the subregular solution model with the Redlich-Kister equation, and those of intermetallic compounds (Ag 2 Er and AgEr phases) were treated as stoichiometric compounds, and Ag 51 Er 14 phase was modeled by the sublattice model in the Ag-Er binary system. The thermodynamic parameters of the Ag-Er and Er-Y binary systems were obtained, and an agreement between the calculated results and experimental data was obtained for each binary system.

  10. Fifty years of shear zones

    Graham, Rodney

    2017-04-01

    We are here, of course, because 1967 saw the publication of John Ramsay's famous book. Two years later a memorable field trip from Imperial College to the Outer Hebrides saw John on a bleak headland on the coast of North Uist where a relatively undeformed metadolerite within Lewisian (Precambrian) gneisses contained ductile shear zones with metamorphic fabrics in amphibolite facies. One particular outcrop was very special - a shear zone cutting otherwise completely isotropic, undeformed metadolerite, with an incremental foliation starting to develop at 45° to the deformation zone, and increasing in intensity as it approached the shear direction. Here was proof of the process of simple shear under ductile metamorphic conditions - the principles of simple shear outlined in John Ramsay's 1967 book clearly visible in nature, and verified by Ramsay's mathematical proofs in the eventual paper (Ramsay and Graham, 1970). Later work on the Lewisian on the mainland of Scotland, in South Harris, in Africa, and elsewhere applied Ramsay's simple shear principles more liberally, more imprecisely and on larger scale than at Caisteal Odair, but in retrospect it documented what seems now to be the generality of mid and lower crustal deformation. Deep seismic reflection data show us that on passive margins hyper-stretched continental crust (whether or not cloaked by Seaward Dipping Reflectors) seems to have collapsed onto the mantle. Crustal faults mostly sole out at or above the mantle - so the Moho is a detachment- an 'outer marginal detachment', if you like, and, of course, it must be a ductile shear. On non-volcanic margins this shear zone forms the first formed ocean floor before true sea floor spreading gets going to create real oceanic crust. Gianreto Manatschal, Marcel Lemoine and others realised that the serpentinites described in parts of the Alps are exposed remnants of this ductile shear zone. Associated ophicalcite breccias tell of sea floor exposure, while high

  11. Ungdomslitteratur former(er) sig

    Henkel, Ayoe Qvist

    2016-01-01

    Igennem en 'mediesensitiv' analyse af romanen "Akavet" af Ronnie Andersen (2014) og perspektivering til andre aktuelle romaner for og med unge undersøger artiklen, hvordan ungdomslitteratur udvikler sig i dialog med digitale og mediebaserede impulser, og hvilke konsekvenser for udsigelserne om...... ungdomsliv og ungdomslitteraturens æstetik og mulige egenart, denne udvikling har. Artiklen baserer sig på en materialitetstilgang særligt inspireret af N. Katherine Hayles, som ikke tidligere har fået opmærksomhed i læsninger af ungdomslitteratur eller i diskussioner af ungdomslitteraturens mulige egenart......, at ungdomslitteratur drejer sig om unges udviklingsproces fra barndom og til voksenhed og dermed skildrer en overgang præget af linearitet, modning og vækst. Artiklen konkluderer, at der er ungdomslitteratur, der realiseres på andre præmisser, og Akavet kan ses som eksponent for en bevægelse fra ungdomslitteratur som...

  12. Low Estrogen Receptor (ER)-Positive Breast Cancer and Neoadjuvant Systemic Chemotherapy: Is Response Similar to Typical ER-Positive or ER-Negative Disease?

    Landmann, Alessandra; Farrugia, Daniel J; Zhu, Li; Diego, Emilia J; Johnson, Ronald R; Soran, Atilla; Dabbs, David J; Clark, Beth Z; Puhalla, Shannon L; Jankowitz, Rachel C; Brufsky, Adam M; Ahrendt, Gretchen M; McAuliffe, Priscilla F; Bhargava, Rohit

    2018-05-08

    Pathologic complete response (pCR) rate after neoadjuvant chemotherapy was compared between 141 estrogen receptor (ER)-negative (43%), 41 low ER+ (13%), 47 moderate ER+ (14%), and 98 high ER+ (30%) tumors. Human epidermal growth factor receptor 2-positive cases, cases without semiquantitative ER score, and patients treated with neoadjuvant endocrine therapy alone were excluded. The pCR rate of low ER+ tumors was similar to the pCR rate of ER- tumors (37% and 26% for low ER and ER- respectively, P = .1722) but significantly different from the pCR rate of moderately ER+ (11%, P = .0049) and high ER+ tumors (4%, P < .0001). Patients with pCR had an excellent prognosis regardless of the ER status. In patients with residual disease (no pCR), the recurrence and death rate were higher in ER- and low ER+ cases compared with moderate and high ER+ cases. Low ER+ breast cancers are biologically similar to ER- tumors. Semiquantitative ER H-score is an important determinant of response to neoadjuvant chemotherapy.

  13. SEDflume - High Shear Stress Flume

    Federal Laboratory Consortium — The U.S. Army Corps of Engineers High Shear Stress flume (SEDflume) is designed for estimating erosion rates of fine-grained and mixed fine/coarse grained sediments...

  14. Multiple band structure in 156Er

    Sunyar, A.W.; Der Mateosian, E.; Kistner, O.C.; Johnson, A.; Lumpkin, A.H.; Thieberger, P.

    1976-01-01

    The 142 Nd( 18 O,4n) 156 Er reaction at 90-95 MeV was used to study 156 Er high-spin states to spin 24. In addition to the background ground-state band, two well developed off-spin side bands, one of each parity, were observed. (Auth.)

  15. Er der en underviser til stede?

    Christiansen, René Boyer; Nortvig, Anne-Mette; Rosenlund, Lea Tilde

    2015-01-01

    I de senere år er MOOC (Massive Open Online Courses) blevet en faktor på uddannelsesområdet. MOOC-forskning er et forholdsvist nyt felt, men har inden for de seneste 2-3 år udviklet sig med hastige skridt (Liyanagunawardena et al. 2013, Bayne & Ross 2014). En stor del af denne forskning har haft...

  16. Coronavirus infection, ER stress and Apoptosis

    TO SING eFUNG

    2014-06-01

    Full Text Available The replication of coronavirus, a family of important animal and human pathogens, is closely associated with the cellular membrane compartments, especially the endoplasmic reticulum (ER. Coronavirus infection of cultured cells was previously shown to cause ER stress and induce the unfolded protein response (UPR, a process that aims to restore the ER homeostasis by global translation shutdown and increasing the ER folding capacity. However under prolonged ER stress, UPR can also induce apoptotic cell death. Accumulating evidence from recent studies has shown that induction of ER stress and UPR may constitute a major aspect of coronavirus-host interaction. Activation of the three branches of UPR modulates a wide variety of signaling pathways, such as mitogen-activated protein (MAP kinases activation, autophagy, apoptosis and innate immune response. ER stress and UPR activation may therefore contribute significantly to the viral replication and pathogenesis during coronavirus infection. In this review, we summarize current knowledge on coronavirus-induced ER stress and UPR activation, with emphasis on their cross-talking to apoptotic signaling.

  17. Led strategisk med 3 F'er

    Klausen, Kurt Klaudi

    2017-01-01

    Artiklen gennemgår kort de tre F'er: at fremskrive, forudse og forestille som strategiske værktøjer til strategic forecast......Artiklen gennemgår kort de tre F'er: at fremskrive, forudse og forestille som strategiske værktøjer til strategic forecast...

  18. Et kors er ikke bare et kors

    Bach-Nielsen, Carsten

    2015-01-01

    Om et kors, der er rejst uden for den danske kirke i Bruxelles; formodentlig en afledning af det såkaldte Brabanterkors.......Om et kors, der er rejst uden for den danske kirke i Bruxelles; formodentlig en afledning af det såkaldte Brabanterkors....

  19. Er formen blevet vigtigst i politik?

    Etemadi, Maziar Haghpaidar

    2005-01-01

    RETORIK: Retorikken er kunsten at tage ordet - skriftligt eller mundtligt - og udtrykke sig smukt og velformuleret. Gorgias (ca. 490-ca. 390 f. Kr.) fra Leontinoi på Sicilien betragtes som ophavsmanden til den første endelige formulering af retorikkens virke og muligheder: "Talen er en mægtig...

  20. En isoleret verden er en bedre verden

    Enrum, Nils

    2014-01-01

    Man skal ikke kaste med sten, hvis man bor i et hus med energimærke D ... Men problemet med varmetab fra danske boliger er til at løse......Man skal ikke kaste med sten, hvis man bor i et hus med energimærke D ... Men problemet med varmetab fra danske boliger er til at løse...

  1. "Det man siger er man selv..."

    Næsby, Torben; Nørgaard, Britta; Uddholm, Mats

    forhold, der er hermeneutisk, strukturelt og relationelt bestemt. Praksisviden kan ikke være objektiv i gængs forstand, men det behøver ikke at diskvalificere denne viden. Forståelse er altid knyttet til den sag og bundet til den situation man står overfor og i som professionel og som menneske....

  2. Size effects in shear interfaces

    GARNIER, J

    2001-01-01

    In physical modelling (centrifuge tests, calibration chambers, laboratory tests), the size of the soil particles may not be negligible when compared to the dimensions of the models. Size effects may so disturb the response of the models and the experimental data obtained on these cannot be extended to true scale conditions. Different tests have been performed to study and quantify the size effects that may happen in shear interfaces between soils and structures : modified shear box tests, pul...

  3. Multifractal spectra in shear flows

    Keefe, L. R.; Deane, Anil E.

    1989-01-01

    Numerical simulations of three-dimensional homogeneous shear flow and fully developed channel flow, are used to calculate the associated multifractal spectra of the energy dissipation field. Only weak parameterization of the results with the nondimensional shear is found, and this only if the flow has reached its asymptotic development state. Multifractal spectra of these flows coincide with those from experiments only at the range alpha less than 1.

  4. Shear Alfven waves in tokamaks

    Kieras, C.E.

    1982-12-01

    Shear Alfven waves in an axisymmetric tokamak are examined within the framework of the linearized ideal MHD equations. Properties of the shear Alfven continuous spectrum are studied both analytically and numerically. Implications of these results in regards to low frequency rf heating of toroidally confined plasmas are discussed. The structure of the spatial singularities associated with these waves is determined. A reduced set of ideal MHD equations is derived to describe these waves in a very low beta plasma

  5. Experimental observation of shear thickening oscillation

    Nagahiro, Shin-ichiro; Nakanishi, Hiizu; Mitarai, Namiko

    2013-01-01

    We report experimental observations of the shear thickening oscillation, i.e. the spontaneous macroscopic oscillation in the shear flow of severe shear thickening fluid. Using a density-matched starch-water mixture, in the cylindrical shear flow of a few centimeters flow width, we observed...

  6. Supervision og de tre k´er

    Schilling, Benedicte; Jacobsen, Claus Haugaard; Nielsen, Jan

    2010-01-01

    Kontrol, kontrakt og kontekst er supervisionens tre k'er. Men hvad er supervision i det hele taget for en størrelse, der spillerså central en rolle for den psykologfaglige profession?......Kontrol, kontrakt og kontekst er supervisionens tre k'er. Men hvad er supervision i det hele taget for en størrelse, der spillerså central en rolle for den psykologfaglige profession?...

  7. Shear strength of non-shear reinforced concrete elements

    Hoang, Cao linh

    1997-01-01

    is based upon the hypothesis that cracks can be transformed into yield lines, which have lower sliding resistance than yield lines formed in uncracked concrete.Proposals have been made on how the derived standard solutions may be applied to more complicated cases, such as continuous beams, beams......The report deals with the shear strength of statically indeterminate reinforced concrete beams without shear reinforcement. Solutions for a number of beams with different load and support conditions have been derived by means of the crack sliding model developed by Jin- Ping Zhang.This model...

  8. Focusing of Shear Shock Waves

    Giammarinaro, Bruno; Espíndola, David; Coulouvrat, François; Pinton, Gianmarco

    2018-01-01

    Focusing is a ubiquitous way to transform waves. Recently, a new type of shock wave has been observed experimentally with high-frame-rate ultrasound: shear shock waves in soft solids. These strongly nonlinear waves are characterized by a high Mach number, because the shear wave velocity is much slower, by 3 orders of magnitude, than the longitudinal wave velocity. Furthermore, these waves have a unique cubic nonlinearity which generates only odd harmonics. Unlike longitudinal waves for which only compressional shocks are possible, shear waves exhibit cubic nonlinearities which can generate positive and negative shocks. Here we present the experimental observation of shear shock wave focusing, generated by the vertical motion of a solid cylinder section embedded in a soft gelatin-graphite phantom to induce linearly vertically polarized motion. Raw ultrasound data from high-frame-rate (7692 images per second) acquisitions in combination with algorithms that are tuned to detect small displacements (approximately 1 μ m ) are used to generate quantitative movies of gel motion. The features of shear shock wave focusing are analyzed by comparing experimental observations with numerical simulations of a retarded-time elastodynamic equation with cubic nonlinearities and empirical attenuation laws for soft solids.

  9. Modeling of shear wall buildings

    Gupta, A K [North Carolina State Univ., Raleigh (USA). Dept. of Civil Engineering

    1984-05-01

    Many nuclear power plant buildings, for example, the auxiliary building, have reinforced concrete shear walls as the primary lateral load resisting system. Typically, these walls have low height to length ratio, often less than unity. Such walls exhibit marked shear lag phenomenon which would affect their bending stiffness and the overall stress distribution in the building. The deformation and the stress distribution in walls have been studied which is applicable to both the short and the tall buildings. The behavior of the wall is divided into two parts: the symmetric flange action and the antisymmetry web action. The latter has two parts: the web shear and the web bending. Appropriate stiffness equations have been derived for all the three actions. These actions can be synthesized to solve any nonlinear cross-section. Two specific problems, that of lateral and torsional loadings of a rectangular box, have been studied. It is found that in short buildings shear lag plays a very important role. Any beam type formulation which either ignores shear lag or includes it in an idealized form is likely to lead to erroneous results. On the other hand a rigidity type approach with some modifications to the standard procedures would yield nearly accurate answers.

  10. En hat er vel en hat ... eller?

    Bøilerehauge, Dorrit

    2007-01-01

    Mens vi kører i høj fart på "the information highway" - i den helt store bus midt på vejen - glemmer vi ofte noget meget vigtigt i vores glæde over, at verden tilsyneladende åbner sig for os, og vi kan kommunikere med hele verden med ét klik. Vi glemmer, at selvom trafikskilte som oftest er ens -...... - så er selve trafikken og forventningerne blandt medtrafikanterne helt forskellige fra det, vi er vant til. Udgivelsesdato: Februar...

  11. Ytringsfriheden er ikke nødvendig

    Lauritzen, Pia

    2008-01-01

    nemlig godt konstatere, at ytringsfriheden ikke er nødvendig uden dermed at give afkald på frihed og demokrati.Vi kan oven i købet mene, at ytringsfriheden ophører med at være frihed, når vi betragter den som nødvendig. Og det er lige nøjagtig det, jeg efterlyser: at vi bruger filosoffer som Immanuel...... Kant og Luigi Pareyson til at forstå, at friheden er betydelig mere kompleks, end vi gør den til i øjeblikket....

  12. Hvordan er det å leve med CRPS?

    Hovind, Thomas

    2014-01-01

    Hensikten med denne studien er å se på hvordan pasienter med komplekst regionalt smertesyndrom (CRPS) opplever å leve med tilstanden og hvordan disse pasientene har opplevd å bli møtt i helsevesenet. CRPS er en langvarig tilstand med sterke smerter som kan medføre økt smerterespons, redusert funksjon og nedsatt livskvalitet hos pasientene. Studien er en kvalitativ undersøkelse basert på dybdeintervju av fire pasienter med CRPS. Pasientene ble rekruttert fra en smerteavdeling i Nord-Norge og u...

  13. Branding er ikke til at komme udenom

    Hermansen, Judy

    2008-01-01

    Søren Askegaard definerer branding som "et iscenesat og afkodet symbolunivers". Det vil sige, at vi på den ene side har virksomhedens strategiske profilering, hvor den forsøger at skabe sig en særlig differentieret og positioneret profil, som adskiller den fra andre virksomheder. "Og det er denne...... strategiske kommunikation, der gør at branding er et ledelsesbegreb og ikke kun et markedsføringsbegreb. Det er ikke staffage, men værdier, som skal gennemsyre alle organisationens aktiviteter." Udgivelsesdato: maj...

  14. Ursodeoxycholic Acid (UDCA) Exerts Anti-Atherogenic Effects by Inhibiting Endoplasmic Reticulum (ER) Stress Induced by Disturbed Flow.

    Chung, Jihwa; Kim, Kyoung Hwa; Lee, Seok Cheol; An, Shung Hyun; Kwon, Kihwan

    2015-10-01

    Disturbed blood flow with low-oscillatory shear stress (OSS) is a predominant atherogenic factor leading to dysfunctional endothelial cells (ECs). Recently, it was found that disturbed flow can directly induce endoplasmic reticulum (ER) stress in ECs, thereby playing a critical role in the development and progression of atherosclerosis. Ursodeoxycholic acid (UDCA), a naturally occurring bile acid, has long been used to treat chronic cholestatic liver disease and is known to alleviate endoplasmic reticulum (ER) stress at the cellular level. However, its role in atherosclerosis remains unexplored. In this study, we demonstrated the anti-atherogenic activity of UDCA via inhibition of disturbed flow-induced ER stress in atherosclerosis. UDCA effectively reduced ER stress, resulting in a reduction in expression of X-box binding protein-1 (XBP-1) and CEBP-homologous protein (CHOP) in ECs. UDCA also inhibits the disturbed flow-induced inflammatory responses such as increases in adhesion molecules, monocyte adhesion to ECs, and apoptosis of ECs. In a mouse model of disturbed flow-induced atherosclerosis, UDCA inhibits atheromatous plaque formation through the alleviation of ER stress and a decrease in adhesion molecules. Taken together, our results revealed that UDCA exerts anti-atherogenic activity in disturbed flow-induced atherosclerosis by inhibiting ER stress and the inflammatory response. This study suggests that UDCA may be a therapeutic agent for prevention or treatment of atherosclerosis.

  15. FEM Simulation of Incremental Shear

    Rosochowski, Andrzej; Olejnik, Lech

    2007-01-01

    A popular way of producing ultrafine grained metals on a laboratory scale is severe plastic deformation. This paper introduces a new severe plastic deformation process of incremental shear. A finite element method simulation is carried out for various tool geometries and process kinematics. It has been established that for the successful realisation of the process the inner radius of the channel as well as the feeding increment should be approximately 30% of the billet thickness. The angle at which the reciprocating die works the material can be 30 deg. . When compared to equal channel angular pressing, incremental shear shows basic similarities in the mode of material flow and a few technological advantages which make it an attractive alternative to the known severe plastic deformation processes. The most promising characteristic of incremental shear is the possibility of processing very long billets in a continuous way which makes the process more industrially relevant

  16. SHEAR ACCELERATION IN EXPANDING FLOWS

    Rieger, F. M. [ZAH, Institut für Theoretische Astrophysik, Universität Heidelberg, Philosophenweg 12, D-69120 Heidelberg (Germany); Duffy, P., E-mail: frank.rieger@mpi-hd.mpg.de, E-mail: peter.duffy@ucd.ie [University College Dublin, Belfield, Dublin 4 (Ireland)

    2016-12-10

    Shear flows are naturally expected to occur in astrophysical environments and potential sites of continuous non-thermal Fermi-type particle acceleration. Here we investigate the efficiency of expanding relativistic outflows to facilitate the acceleration of energetic charged particles to higher energies. To this end, the gradual shear acceleration coefficient is derived based on an analytical treatment. The results are applied to the context of the relativistic jets from active galactic nuclei. The inferred acceleration timescale is investigated for a variety of conical flow profiles (i.e., power law, Gaussian, Fermi–Dirac) and compared to the relevant radiative and non-radiative loss timescales. The results exemplify that relativistic shear flows are capable of boosting cosmic-rays to extreme energies. Efficient electron acceleration, on the other hand, requires weak magnetic fields and may thus be accompanied by a delayed onset of particle energization and affect the overall jet appearance (e.g., core, ridge line, and limb-brightening).

  17. ER Consolidated Quarterly Report October 2014

    Cochran, John R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-01

    This Environmental Restoration Operations (ER) Consolidated Quarterly Report (ER Quarterly Report) provides the status of ongoing corrective actions and related Long- Term Stewardship (LTS) activities being implemented by Sandia National Laboratories, New Mexico (SNL/NM) ER for the April, May, and June 2014 quarterly reporting period. Section 2.0 provides the status of ER Operations activities including closure activities for the Mixed Waste Landfill (MWL), project management and site closure, and hydrogeologic characterizations. Section 3.0 provides the status of LTS activities that relate to the Chemical Waste Landfill (CWL) and the associated Corrective Action Management Unit (CAMU). Section 4.0 provides the references noted in Section I of this report.

  18. Computerized lateral-shear interferometer

    Hasegan, Sorin A.; Jianu, Angela; Vlad, Valentin I.

    1998-07-01

    A lateral-shear interferometer, coupled with a computer for laser wavefront analysis, is described. A CCD camera is used to transfer the fringe images through a frame-grabber into a PC. 3D phase maps are obtained by fringe pattern processing using a new algorithm for direct spatial reconstruction of the optical phase. The program describes phase maps by Zernike polynomials yielding an analytical description of the wavefront aberration. A compact lateral-shear interferometer has been built using a laser diode as light source, a CCD camera and a rechargeable battery supply, which allows measurements in-situ, if necessary.

  19. Er iPad digital udeskole?

    Schilhab, Theresa

    2014-01-01

    Hvor ’konkret’ skal en oplevelse være, for at intuitionen om, at det selvoplevede styrker læringen, holder? Er brug af tablets (e.g. iPads) et ligebyrdigt alternativ til den konkrete oplevelse?......Hvor ’konkret’ skal en oplevelse være, for at intuitionen om, at det selvoplevede styrker læringen, holder? Er brug af tablets (e.g. iPads) et ligebyrdigt alternativ til den konkrete oplevelse?...

  20. Snip snap snude - dobbelthagerne er ude

    Larsen, Malene Charlotte; Kofoed, Jette

    2015-01-01

    Det handler om at være grim. Det står i skarp kontrast til det pæne og polerede på Instagram. Det er flygtigt, useriøst og ligegyldigt. Og så forsvinder det heldigvis igen, så man behøver kun at forholde sig til det i de få sekunder, det foregår. Snapchat vokser i popularitet og er nu det...

  1. Håndbold er en praksis!

    Olsen, Poul Bitsch

    2008-01-01

    Dansk håndbold er en kæmpemæssig succeshistorie. Ser man snævert på den udvikling, elitedelen af sporten har gennemlevet de seneste 15 år, viser stort set alle tænkelige parametre fremgang. De internationale resultater for lands og klubhold er med få udfald blevet stadigt bedre, omsætningen i klu...

  2. Arctigenin alleviates ER stress via activating AMPK

    Gu, Yuan; Sun, Xiao-xiao; Ye, Ji-ming; He, Li; Yan, Shou-sheng; Zhang, Hao-hao; Hu, Li-hong; Yuan, Jun-ying; Yu, Qiang

    2012-01-01

    Aim: To investigate the protective effects of arctigenin (ATG), a phenylpropanoid dibenzylbutyrolactone lignan from Arctium lappa L (Compositae), against ER stress in vitro and the underlying mechanisms. Methods: A cell-based screening assay for ER stress regulators was established. Cell viability was measured using MTT assay. PCR and Western blotting were used to analyze gene and protein expression. Silencing of the CaMKKβ, LKB1, and AMPKα1 genes was achieved by RNA interference (RNAi). An ATP bioluminescent assay kit was employed to measure the intracellular ATP levels. Results: ATG (2.5, 5 and 10 μmol/L) inhibited cell death and unfolded protein response (UPR) in a concentration-dependent manner in cells treated with the ER stress inducer brefeldin A (100 nmol/L). ATG (1, 5 and 10 μmol/L) significantly attenuated protein synthesis in cells through inhibiting mTOR-p70S6K signaling and eEF2 activity, which were partially reversed by silencing AMPKα1 with RNAi. ATG (1-50 μmol/L) reduced intracellular ATP level and activated AMPK through inhibiting complex I-mediated respiration. Pretreatment of cells with the AMPK inhibitor compound C (25 μmol/L) rescued the inhibitory effects of ATG on ER stress. Furthermore, ATG (2.5 and 5 μmol/L) efficiently activated AMPK and reduced the ER stress and cell death induced by palmitate (2 mmol/L) in INS-1 β cells. Conclusion: ATG is an effective ER stress alleviator, which protects cells against ER stress through activating AMPK, thus attenuating protein translation and reducing ER load. PMID:22705729

  3. Bæredygtighed hos SMV'er

    2016-01-01

    Valg af materiale/medie/form: YouTube Valg af arbejdsform: Videoerne kan bruges som caseundervisning Begrundelse for valg af materiale/medie/form/arbejdsform: Caseundervisning er velegnet til at lære om praksis......Valg af materiale/medie/form: YouTube Valg af arbejdsform: Videoerne kan bruges som caseundervisning Begrundelse for valg af materiale/medie/form/arbejdsform: Caseundervisning er velegnet til at lære om praksis...

  4. Hvad litteraturen kan, er ofte det rigtige ..

    Bundsgaard, Jeppe; Kühn, Lisbet

    2010-01-01

    Læsning i dansk handler i første omgang om at blive god til at læse, men på mellemtrinnet er det ved at være tiden til også at bruge skønlitteraturen til det, den er god til, nemlig til at få indsigt i menneskelivets kompleksitet. I dette kapitel anbefales det at gøre noget med litteraturen, fx f...

  5. Hvilke Dødehavstekster er "sekteriske"?

    Holst, Søren

    2003-01-01

    Skønt Dødehavsrullerne antageligt tilhørte en gruppering, der boede i Qumran, tyder alt på, at mange af teksterne er forfattet andre steder. Artiklen undersøger den særlige sprogbrug, som antageligt er typisk for Qumran-samfundet, og som præger forbavsende få af tekserne. En meget stor del af...

  6. Trump er godt nyt for verdensfreden

    Jakobsen, Peter Viggo

    2017-01-01

    Trumps uberegnelighed øger ikke risikoen for krig. Den mindsker den ved at få de allierede til at gøre mere og modstanderne til at forhandle. Det er godt for verdensfreden......Trumps uberegnelighed øger ikke risikoen for krig. Den mindsker den ved at få de allierede til at gøre mere og modstanderne til at forhandle. Det er godt for verdensfreden...

  7. Characterization of the ER-Targeted Low Affinity Ca2+ Probe D4ER

    Elisa Greotti

    2016-09-01

    Full Text Available Calcium ion (Ca2+ is a ubiquitous intracellular messenger and changes in its concentration impact on nearly every aspect of cell life. Endoplasmic reticulum (ER represents the major intracellular Ca2+ store and the free Ca2+ concentration ([Ca2+] within its lumen ([Ca2+]ER can reach levels higher than 1 mM. Several genetically-encoded ER-targeted Ca2+ sensors have been developed over the last years. However, most of them are non-ratiometric and, thus, their signal is difficult to calibrate in live cells and is affected by shifts in the focal plane and artifactual movements of the sample. On the other hand, existing ratiometric Ca2+ probes are plagued by different drawbacks, such as a double dissociation constant (Kd for Ca2+, low dynamic range, and an affinity for the cation that is too high for the levels of [Ca2+] in the ER lumen. Here, we report the characterization of a recently generated ER-targeted, Förster resonance energy transfer (FRET-based, Cameleon probe, named D4ER, characterized by suitable Ca2+ affinity and dynamic range for monitoring [Ca2+] variations within the ER. As an example, resting [Ca2+]ER have been evaluated in a known paradigm of altered ER Ca2+ homeostasis, i.e., in cells expressing a mutated form of the familial Alzheimer’s Disease-linked protein Presenilin 2 (PS2. The lower Ca2+ affinity of the D4ER probe, compared to that of the previously generated D1ER, allowed the detection of a conspicuous, more clear-cut, reduction in ER Ca2+ content in cells expressing mutated PS2, compared to controls.

  8. ER-to-plasma membrane tethering proteins regulate cell signaling and ER morphology.

    Manford, Andrew G; Stefan, Christopher J; Yuan, Helen L; Macgurn, Jason A; Emr, Scott D

    2012-12-11

    Endoplasmic reticulum-plasma membrane (ER-PM) junctions are conserved structures defined as regions of the ER that tightly associate with the plasma membrane. However, little is known about the mechanisms that tether these organelles together and why such connections are maintained. Using a quantitative proteomic approach, we identified three families of ER-PM tethering proteins in yeast: Ist2 (related to mammalian TMEM16 ion channels), the tricalbins (Tcb1/2/3, orthologs of the extended synaptotagmins), and Scs2 and Scs22 (vesicle-associated membrane protein-associated proteins). Loss of all six tethering proteins results in the separation of the ER from the PM and the accumulation of cytoplasmic ER. Importantly, we find that phosphoinositide signaling is misregulated at the PM, and the unfolded protein response is constitutively activated in the ER in cells lacking ER-PM tether proteins. These results reveal critical roles for ER-PM contacts in cell signaling, organelle morphology, and ER function. Copyright © 2012 Elsevier Inc. All rights reserved.

  9. Grouted Connections with Shear Keys

    Pedersen, Ronnie; Jørgensen, M. B.; Damkilde, Lars

    2012-01-01

    This paper presents a finite element model in the software package ABAQUS in which a reliable analysis of grouted pile-to-sleeve connections with shear keys is the particular purpose. The model is calibrated to experimental results and a consistent set of input parameters is estimated so that dif...... that different structural problems can be reproduced successfully....

  10. Meniscal shear stress for punching.

    Tuijthof, Gabrielle J M; Meulman, Hubert N; Herder, Just L; van Dijk, C Niek

    2009-01-01

    Experimental determination of the shear stress for punching meniscal tissue. Meniscectomy (surgical treatment of a lesion of one of the menisci) is the most frequently performed arthroscopic procedure. The performance of a meniscectomy is not optimal with the currently available instruments. To design new instruments, the punching force of meniscal tissue is an important parameter. Quantitative data are unavailable. The meniscal punching process was simulated by pushing a rod through meniscal tissue at constant speed. Three punching rods were tested: a solid rod of Oslash; 3.00 mm, and two hollow tubes (Oslash; 3.00-2.60 mm) with sharpened cutting edges of 0.15 mm and 0.125 mm thick, respectively. Nineteen menisci acquired from 10 human cadaveric knee joints were punched (30 tests). The force and displacement were recorded from which the maximum shear stress was determined (average added with three times the standard deviation). The maximum shear stress for the solid rod was determined at 10.2 N/mm2. This rod required a significantly lower punch force in comparison with the hollow tube having a 0.15 mm cutting edge (plt;0.01). The maximum shear stress for punching can be applied to design instruments, and virtual reality training environments. This type of experiment is suitable to form a database with material properties of human tissue similar to databases for the manufacturing industry.

  11. Centrifuges and inertial shear forces

    Loon, van J.J.W.A.; Folgering, H.T.E.; Bouten, C.V.C.; Smit, T.H.

    2004-01-01

    Centrifuges are often used in biological studies for 1xg control samples in space flight microgravity experiments as well as in ground based research. Using centrifugation as a tool to generate an Earth like acceleration introduces unwanted inertial shear forces to the sample. Depending on the

  12. A study on fixing force generation mechanism of ER gel

    Tanaka, H; Kakinuma, Y; Aoyama, T; Anzai, H

    2009-01-01

    Electro-rheological Gel (ERG) is a new functional elastomer which changes its surface frictional and adhesive property according to the intensity of applied electrical field. This unique property is called ERG effect. The upper sliding electrode placed on the surface of ERG is fixed by the adhesive effect of ERG under electrical field. Variable fixing forces due to adhesion are generated by this effect. However, relationship between physical factors and generated fixing force has not yet been clarified. In this study, physical mechanism of fixing phenomenon is elucidated experimentally from the view point of frictional force and adhesive force. From the results, empirical equation of generated fixing force is originally derived to establish the theory of ERG effect.

  13. A study on fixing force generation mechanism of ER gel

    Tanaka, H; Kakinuma, Y; Aoyama, T [School of Integrated Design Engineering, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan); Anzai, H [Fujikura kasei Co., Ltd., 2-6-15 Shibakouen, Minato-ku, Tokyo (Japan)], E-mail: h-tanaka@ina.sd.keio.ac.jp

    2009-02-01

    Electro-rheological Gel (ERG) is a new functional elastomer which changes its surface frictional and adhesive property according to the intensity of applied electrical field. This unique property is called ERG effect. The upper sliding electrode placed on the surface of ERG is fixed by the adhesive effect of ERG under electrical field. Variable fixing forces due to adhesion are generated by this effect. However, relationship between physical factors and generated fixing force has not yet been clarified. In this study, physical mechanism of fixing phenomenon is elucidated experimentally from the view point of frictional force and adhesive force. From the results, empirical equation of generated fixing force is originally derived to establish the theory of ERG effect.

  14. Shear banding, discontinuous shear thickening, and rheological phase transitions in athermally sheared frictionless disks

    Vâgberg, Daniel; Olsson, Peter; Teitel, S.

    2017-05-01

    We report on numerical simulations of simple models of athermal, bidisperse, soft-core, massive disks in two dimensions, as a function of packing fraction ϕ , inelasticity of collisions as measured by a parameter Q , and applied uniform shear strain rate γ ˙. Our particles have contact interactions consisting of normally directed elastic repulsion and viscous dissipation, as well as tangentially directed viscous dissipation, but no interparticle Coulombic friction. Mapping the phase diagram in the (ϕ ,Q ) plane for small γ ˙, we find a sharp first-order rheological phase transition from a region with Bagnoldian rheology to a region with Newtonian rheology, and show that the system is always Newtonian at jamming. We consider the rotational motion of particles and demonstrate the crucial importance that the coupling between rotational and translational degrees of freedom has on the phase structure at small Q (strongly inelastic collisions). At small Q , we show that, upon increasing γ ˙, the sharp Bagnoldian-to-Newtonian transition becomes a coexistence region of finite width in the (ϕ ,γ ˙) plane, with coexisting Bagnoldian and Newtonian shear bands. Crossing this coexistence region by increasing γ ˙ at fixed ϕ , we find that discontinuous shear thickening can result if γ ˙ is varied too rapidly for the system to relax to the shear-banded steady state corresponding to the instantaneous value of γ ˙.

  15. Synthesis of Er and Er : Yb doped sol–gel derived silica glass and ...

    Unknown

    Materials Science Centre, †Central Research Facility, Optical Fibre Unit, Indian Institute of Technology,. Kharagpur 721 302, India. MS received 1 March 2004; revised 4 July 2004. Abstract. Er3+ and Er3+ : Yb3+ doped optical quality, crack and bubble free glasses for possible use in mak- ing laser material have been ...

  16. Shear behaviour of reinforced phyllite concrete beams

    Adom-Asamoah, Mark; Owusu Afrifa, Russell

    2013-01-01

    Highlights: ► Phyllite concrete beams often exhibited shear with anchorage bond failure. ► Different shear design provisions for reinforced phyllite beams are compared. ► Predicted shear capacity of phyllite beams must be modified by a reduction factor. -- Abstract: The shear behaviour of concrete beams made from phyllite aggregates subjected to monotonic and cyclic loading is reported. First diagonal shear crack load of beams with and without shear reinforcement was between 42–58% and 42–92% of the failure loads respectively. The phyllite concrete beams without shear links had lower post-diagonal cracking shear resistance compared to corresponding phyllite beams with shear links. As a result of hysteretic energy dissipation, limited cyclic loading affected the stiffness, strength and deformation of the phyllite beams with shear reinforcement. Generally, beams with and without shear reinforcement showed anchorage bond failure in addition to the shear failure due to high stress concentration near the supports. The ACI, BS and EC codes are conservative for the prediction of phyllite concrete beams without shear reinforcement but they all overestimate the shear strength of phyllite concrete beams with shear reinforcement. It is recommended that the predicted shear capacity of phyllite beams reinforced with steel stirrups be modified by a reduction factor of 0.7 in order to specify a high enough safety factor on their ultimate strength. It is also recommended that susceptibility of phyllite concrete beams to undergo anchorage bond failure is averted in design by the provision of greater anchorage lengths than usually permitted.

  17. Site of Er ions in silica layers codoped with Si nanoclusters and Er

    Pellegrino, P.; Garrido, B.; Arbiol, J.; Garcia, C.; Lebour, Y.; Morante, J.R.

    2006-01-01

    Silica layers implanted with Si and Er ions to various doses and annealed at 950 deg. C have been investigated by means of energy-filtered transmission electron microscopy (EFTEM) and high annular angle dark field (HAADF). EFTEM analysis reveals Si nanoclusters (Si-nc) with an average size around 3 nm for high Si content (15 at. %) whereas no clusters can be imaged for the lowest Si excess (5 at. %). Raman scattering supports that amorphous Si precipitates are present in all the samples. Moreover, the filtered images show that Er ions appear preferentially located outside the Si-nc. HAADF analysis confirms that the Er atoms form agglomerations of 5-10 nm size when the Er concentration exceeds 1x10 20 cm -3 . This observation correlates well with the reduction of the Er population excitable by Si nanoclusters, in the best case corresponding to 10% of the total. A suitable tuning of the annealing drastically reduces this deleterious effect

  18. Shear instability of a gyroid diblock copolymer

    Eskimergen, Rüya; Mortensen, Kell; Vigild, Martin Etchells

    2005-01-01

    -induced destabilization is discussed in relation to analogous observations on shear-induced order-to-order and disorder-to-order transitions observed in related block copolymer systems and in microemulsions. It is discussed whether these phenomena originate in shear-reduced fluctuations or shear-induced dislocations....

  19. Study on shear properties of coral sand under cyclic simple shear condition

    Ji, Wendong; Zhang, Yuting; Jin, Yafei

    2018-05-01

    In recent years, the ocean development in our country urgently needs to be accelerated. The construction of artificial coral reefs has become an important development direction. In this paper, experimental studies of simple shear and cyclic simple shear of coral sand are carried out, and the shear properties and particle breakage of coral sand are analyzed. The results show that the coral sand samples show an overall shear failure in the simple shear test, which is more accurate and effective for studying the particle breakage. The shear displacement corresponding to the peak shear stress of the simple shear test is significantly larger than that corresponding to the peak shear stress of the direct shear test. The degree of particle breakage caused by the simple shear test is significantly related to the normal stress level. The particle breakage of coral sand after the cyclic simple shear test obviously increases compared with that of the simple shear test, and universal particle breakage occurs within the whole particle size range. The increasing of the cycle-index under cyclic simple shear test results in continuous compacting of the sample, so that the envelope curve of peak shearing force increases with the accumulated shear displacement.

  20. Statistical Model of Extreme Shear

    Larsen, Gunner Chr.; Hansen, Kurt Schaldemose

    2004-01-01

    In order to continue cost-optimisation of modern large wind turbines, it is important to continously increase the knowledge on wind field parameters relevant to design loads. This paper presents a general statistical model that offers site-specific prediction of the probability density function...... by a model that, on a statistically consistent basis, describe the most likely spatial shape of an extreme wind shear event. Predictions from the model have been compared with results from an extreme value data analysis, based on a large number of high-sampled full-scale time series measurements...... are consistent, given the inevitabel uncertainties associated with model as well as with the extreme value data analysis. Keywords: Statistical model, extreme wind conditions, statistical analysis, turbulence, wind loading, statistical analysis, turbulence, wind loading, wind shear, wind turbines....

  1. Shear failure of granular materials

    Degiuli, Eric; Balmforth, Neil; McElwaine, Jim; Schoof, Christian; Hewitt, Ian

    2012-02-01

    Connecting the macroscopic behavior of granular materials with the microstructure remains a great challenge. Recent work connects these scales with a discrete calculus [1]. In this work we generalize this formalism from monodisperse packings of disks to 2D assemblies of arbitrarily shaped grains. In particular, we derive Airy's expression for a symmetric, divergence-free stress tensor. Using these tools, we derive, from first-principles and in a mean-field approximation, the entropy of frictional force configurations in the Force Network Ensemble. As a macroscopic consequence of the Coulomb friction condition at contacts, we predict shear failure at a critical shear stress, in accordance with the Mohr-Coulomb failure condition well known in engineering. Results are compared with numerical simulations, and the dependence on the microscopic geometric configuration is discussed. [4pt] [1] E. DeGiuli & J. McElwaine, PRE 2011. doi: 10.1103/PhysRevE.84.041310

  2. DNA as a component of ER materials

    Minagawa, K; Aoki, Y; Berber, M R; Mori, T; Tanaka, M

    2009-01-01

    Deoxyribonucleic acid (DNA), which is known as a typical biopolymer, has been utilized for a few types of ER materials. Suspensions were prepared with the particles of DNA, DNA/lipid complexes, and LDH (layered double hydroxide)/DNA composites. The purified DNA showed larger ER effect than the others, but this particle tended to absorb water, which caused less stability. Preliminary experiments of preparing composite with LDH indicated that this inorganic material would be useful for hydrophobic modification of DNA particles, although further optimization of composite preparation is needed. In addition, the LDH/DNA suspensions showed interesting behaviours under some conditions, which indicated possibility for controlling ER property in a wide range.

  3. DNA as a component of ER materials

    Minagawa, K; Aoki, Y; Berber, M R [Institute of Technology and Science, University of Tokushima, Tokushima 770-8506 (Japan); Mori, T [Department of Applied Chemistry, Faculty of Engineering, Kyushu University, Fukuoka 819-0395 (Japan); Tanaka, M [Faculty of Pharmaceutical Science, Tokushima Bunri University, Tokushima 770-8514 (Japan)], E-mail: minagawa@chem.tokushima-u.ac.jp

    2009-02-01

    Deoxyribonucleic acid (DNA), which is known as a typical biopolymer, has been utilized for a few types of ER materials. Suspensions were prepared with the particles of DNA, DNA/lipid complexes, and LDH (layered double hydroxide)/DNA composites. The purified DNA showed larger ER effect than the others, but this particle tended to absorb water, which caused less stability. Preliminary experiments of preparing composite with LDH indicated that this inorganic material would be useful for hydrophobic modification of DNA particles, although further optimization of composite preparation is needed. In addition, the LDH/DNA suspensions showed interesting behaviours under some conditions, which indicated possibility for controlling ER property in a wide range.

  4. Haptic Edge Detection Through Shear

    Platkiewicz, Jonathan; Lipson, Hod; Hayward, Vincent

    2016-03-01

    Most tactile sensors are based on the assumption that touch depends on measuring pressure. However, the pressure distribution at the surface of a tactile sensor cannot be acquired directly and must be inferred from the deformation field induced by the touched object in the sensor medium. Currently, there is no consensus as to which components of strain are most informative for tactile sensing. Here, we propose that shape-related tactile information is more suitably recovered from shear strain than normal strain. Based on a contact mechanics analysis, we demonstrate that the elastic behavior of a haptic probe provides a robust edge detection mechanism when shear strain is sensed. We used a jamming-based robot gripper as a tactile sensor to empirically validate that shear strain processing gives accurate edge information that is invariant to changes in pressure, as predicted by the contact mechanics study. This result has implications for the design of effective tactile sensors as well as for the understanding of the early somatosensory processing in mammals.

  5. CFD simulation of estimating critical shear stress for cleaning flat ...

    Sumit Kawale

    2017-11-22

    Nov 22, 2017 ... Jet impingement; wall shear stress; cleaning of flat plate; turbulence model; critical shear stress; ... On comparing the theoretical predictions with wall shear ... distance and Reynolds number on peak value of local shear stress ...

  6. Bond strength of resin cement to CO2 and Er:YAG laser-treated zirconia ceramic

    Shahin Kasraei

    2014-11-01

    Full Text Available Objectives It is difficult to achieve adhesion between resin cement and zirconia ceramics using routine surface preparation methods. The aim of this study was to evaluate the effects of CO2 and Er:YAG laser treatment on the bond strength of resin cement to zirconia ceramics. Materials and Methods In this in-vitro study 45 zirconia disks (6 mm in diameter and 2 mm in thickness were assigned to 3 groups (n = 15. In control group (CNT no laser treatment was used. In groups COL and EYL, CO2 and Er:YAG lasers were used for pretreatment of zirconia surface, respectively. Composite resin disks were cemented on zirconia disk using dual-curing resin cement. Shear bond strength tests were performed at a crosshead speed of 0.5 mm/min after 24 hr distilled water storage. Data were analyzed by one-way ANOVA and post hoc Tukey's HSD tests. Results The means and standard deviations of shear bond strength values in the EYL, COL and CNT groups were 8.65 ± 1.75, 12.12 ± 3.02, and 5.97 ± 1.14 MPa, respectively. Data showed that application of CO2 and Er:YAG lasers resulted in a significant higher shear bond strength of resin cement to zirconia ceramics (p < 0.0001. The highest bond strength was recorded in the COL group (p < 0.0001. In the CNT group all the failures were adhesive. However, in the laser groups, 80% of the failures were of the adhesive type. Conclusions Pretreatment of zirconia ceramic via CO2 and Er:YAG laser improves the bond strength of resin cement to zirconia ceramic, with higher bond strength values in the CO2 laser treated samples.

  7. ARM CLASIC ER2 CRS/EDOP

    Gerald Heymsfield

    2010-12-20

    Data was taken with the NASA ER-2 aircraft with the Cloud Radar System and other instruments in conjunction with the DOE ARM CLASIC field campaign. The flights were near the SGP site in north Central Oklahoma and targeted small developing convection. The CRS is a 94 GHz nadir pointing Doppler radar. Also on board the ER-2 was the Cloud Physics Lidar (CPL). Seven science flights were conducted but the weather conditions did not cooperate in that there was neither developing convection, or there was heavy rain.

  8. Psyken er en grænseflade

    Hoffmeyer, Jesper

    2011-01-01

    En computer er i sig selv blot et stykke mekanik. Det afgørende sker i mødet mellem maskinen, mennesker og fællesskaber: på grænsefladen. Præcis som hos levende væsner......En computer er i sig selv blot et stykke mekanik. Det afgørende sker i mødet mellem maskinen, mennesker og fællesskaber: på grænsefladen. Præcis som hos levende væsner...

  9. Continuous shear - a method for studying material elements passing a stationary shear plane

    Lindegren, Maria; Wiwe, Birgitte; Wanheim, Tarras

    2003-01-01

    circumferential groove. Normally shear in metal forming processes is of another nature, namely where the material elements move through a stationary shear zone, often of small width. In this paper a method enabling the simulation of this situation is presented. A tool for continuous shear has beeen manufactured...... and tested with AlMgSil and copper. The sheared material has thereafter been tested n plane strain compression with different orientation concerning the angle between the shear plane and the compression direction....

  10. ER Stress: A Therapeutic Target in Rheumatoid Arthritis?

    Rahmati, Marveh; Moosavi, Mohammad Amin; McDermott, Michael F

    2018-04-22

    Diverse physiological and pathological conditions that impact on protein folding of the endoplasmic reticulum (ER) cause ER stress. The unfolded protein response (UPR) and the ER-associated degradation (ERAD) pathway are activated to cope with ER stress. In rheumatoid arthritis (RA), inflammation and ER stress work in parallel by driving inflammatory cells to release cytokines that induce chronic ER stress pathways. This chronic ER stress may contribute to the pathogenesis of RA through synoviocyte proliferation and proinflammatory cytokine production. Therefore, ER stress pathways and their constituent elements are attractive targets for RA drug development. In this review, we integrate current knowledge of the contribution of ER stress to the overall pathogenesis of RA, and suggest some therapeutic implications of these discoveries. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. Simulations of Granular Particles Under Cyclic Shear

    Royer, John; Chaikin, Paul

    2012-02-01

    We perform molecular dynamics (MD) simulations of spherical grains subjected to cyclic, quasi-static shear in a 3D parallelepiped shear cell. This virtual shear cell is constructed out of rough, bumpy walls in order to minimize wall-induced ordering and has an open top surface to allow the packing to readily dilate or compact. Using a standard routine for MD simulations of frictional grains, we simulate over 1000 shear cycles, measuring grain displacements, the local packing density and changes in the contact network. Varying the shear amplitude and the friction coefficient between grains, we map out a phase diagram for the different types of behavior exhibited by these sheared grains. With low friction and high enough shear, the grains can spontaneously order into densely packed crystals. With low shear and increasing friction the packing remains disordered, yet the grains arrange themselves into configurations which exhibit limit cycles where all grains return to the same position after each full shear cycle. At higher shear and friction there is a transition to a diffusive state, where grains continue rearrange and move throughout the shear cell.

  12. Ledelse af samskabelse er en ny ledelsesdisciplin

    Ulrich, Jens; Martin Nielsen, Kim; Bartram, Jan

    2018-01-01

    Samskabelse er blevet det nye orienteringspunkt for rigtig mange offentlige organisationer. Det skyldes en udbredt konsensus om, at velfærdsopgaverne ikke kan løses inden for de vante organisatoriske rammer, men må løses i tæt kontakt med de parter, som opgaverne vedrører. Denne nye tilgang til...

  13. Der er fuld religionsfrihed i Danmark, men..

    Christoffersen, Lisbet

    2018-01-01

    Artiklen analyserer en rapport, udgivet af FN's special rapporteur on Freedom of Religion and Belief, Heiner Bielefeldt. Rapporten vedrører Danmark. Analysen tilslutter sig rapporten på de fleste punkter, men kritiserer begrebet 'blød diskrimination'; kritiserer at rapporten ikke er gået tættere på...

  14. Hvad er kildekritik?

    Olden-Jørgensen, Sebastian

    2009-01-01

    Hvad er Kildekritik? I stedet for at forstå kildekritik som et stringent system, grundlagt af Leopold von Ranke og i Danmark kanoniseret af Kristian Erslev, kunne man med større historiografisk ret og faglig frugtbarhed opfatte kildekritikken som en faglig tradition med tre lag afsat (sedimentere...

  15. Hvad er PET og fMRI?

    B. Paulson, Olaf; Balslev, Daniela; Gerlach, Christian

    2007-01-01

    Hvilken rolle spiller følelserne for vores tankeliv, og hvorfor har vi overhovedet følelser? I kraft af avancerede hjerneskanningsteknikker er den moderne hjernevidenskab blevet i stand til at besvare disse spørgsmål. Gennem artiklerne i denne antologi, skrevet af ledende danske forskere, bliver ...

  16. Creating Smart-er Cities: An Overview

    Allwinkle, Sam; Cruickshank, Peter

    2011-01-01

    The following offers an overview of what it means for cities to be "smart." It draws the supporting definitions and critical insights into smart cities from a series of papers presented at the 2009 Trans-national Conference on Creating Smart(er) Cities. What the papers all have in common is their desire to overcome the all too often…

  17. Geometric calibration of ERS satellite SAR images

    Mohr, Johan Jacob; Madsen, Søren Nørvang

    2001-01-01

    Geometric calibration of the European Remote Sensing (ERS) Satellite synthetic aperture radar (SAR) slant range images is important in relation to mapping areas without ground reference points and also in relation to automated processing. The relevant SAR system parameters are discussed...

  18. Er nogen mere lige end andre?

    Møberg, Rasmus Juul

    normativ fordring. Kohlis (2007) formulering af normalbiografien er en tredeling af livsforløbet (uddannelse – arbejdsliv - pension). En tredeling der bliver kritiseret for at være køns- og familieblind, hvorfor linked lives-begrebet bliver introduceret. Begrebet har den teoretiske implikation...... analyser tager højde for afhængighed over tid i den afhængige variabel. Overordnet set er det tre aspekter af datas karakteristika, der fordrer specielle metoder. Det er censurering af data, tidsmæssig variation i de uafhængige variable samt potentiel korrelation mellem målingerne af den afhængige variabel...... for disse ændringer, hvorved risikoen for en given transition beregnes mere præcist. Afhandlingens empiriske grundlag er registerdata for alle personer i Danmark, der tilhører fødselskohorterne 1968, 1972 og 1976. Data dækker over personlige, familiære forhold og oplysninger på arbejdspladsniveau, hvor den...

  19. Hvad nu hvis sommerfuglen er ekshibitionist?

    Rösing, Lilian Munk

    2008-01-01

    Groft sagt vil denne artikel, ved at aflæse hvad hhv. Inger Christensen, Sigmund Freud og Jacques Lacan har at sige om sommerfugle, argumentere for at der er et afgørende skel mellem naturvidenskab og litteraturvidenskab; mellem naturen, dyret, sommerfuglen på den ene side og bevidstheden...

  20. Hvad er hjemkundskabslæreren?

    Benn, Jette

    2009-01-01

        En appetizer: De praktisk-musiske fag på dagsordenen Temaet for denne artikel er hjemkundskabsfaget, -professionen og dens praktisering belyst gennem et interviewstudie fra 2008 af lærerstuderende og deres lærere. Dette studie relateres til forfatterens tidligere studie af fag og profession i...

  1. Er Storm P. en hardcore vagabond?

    Sortkær, Allan

    2002-01-01

    Den vagabond, som vi kender som Storm P.s, er ikke en figur, der kom fra en guddommelig inspiration eller deslige. Den var en allerede velkendt figur, før Storm P. tog den til sig, og figuren gennemgik radikale forandringer gennem Storm P.s liv: Krads social satire, hypervoldelig eller hyggelig...

  2. Er Frank rationel demokrat eller naiv fetichist?

    Rösing, Lilian Munk

    2014-01-01

    Artiklen er en diskussion af demokrati-begrebet i Rune Lykkebergs Alle har ret. Over for Lykkebregs demokrati-begreb sætter den Rancières og Zizeks forståelse af demokratiet som en åbning for det, den sociale orden ikke kan rumme. Det fører til en kritik af Lykkebergs anvendelse af begreberne om...

  3. Hvad er militær ledelse?

    Barfod, Jakob Rømer

    militær ledelse unik og derved muliggøre en opdeling, således at Forsvarets skoler kun underviser i den del af ledelse, som andre civile uddannelsesinstitutioner ikke menes at kunne undervise i. Men er det muligt at adskille begreber og praksis på den måde? Dette brief undersøger nogle betydninger af...

  4. Finanskrisen - er den markedsorienterede regulering skurken?

    Grosen, Anders

    2009-01-01

    markedsorienterede opgørelse tilsyneladende skyld i bankernes dårlige resultater. I hvert fald er standardsætteren inden for international regnskabsregulering, IASB, i efteråret 2008 på rekordtid kommet de betrængte virksomheder - herunder bankerne - til undsætning med en regnskabsmæssig hjælpepakke som supplement...

  5. Effects of material growth technique and Mg doping on Er3+ photoluminescence in Er-implanted GaN

    Kim, S.; Henry, R. L.; Wickenden, A. E.; Koleske, D. D.; Rhee, S. J.; White, J. O.; Myoung, J. M.; Kim, K.; Li, X.; Coleman, J. J.

    2001-01-01

    Photoluminescence (PL) and photoluminescence excitation (PLE) spectroscopies have been carried out at 6 K on the ∼1540 nm 4 I 13/2 - 4 I 15/2 emissions of Er 3+ in Er-implanted and annealed GaN. These studies revealed the existence of multiple Er 3+ centers and associated PL spectra in Er-implanted GaN films grown by metalorganic chemical vapor deposition, hydride vapor phase epitaxy, and molecular beam epitaxy. The results demonstrate that the multiple Er 3+ PL centers and below-gap defect-related absorption bands by which they are selectively excited are universal features of Er-implanted GaN grown by different techniques. It is suggested that implantation-induced defects common to all the GaN samples are responsible for the Er site distortions that give rise to the distinctive, selectively excited Er 3+ PL spectra. The investigations of selectively excited Er 3+ PL and PLE spectra have also been extended to Er-implanted samples of Mg-doped GaN grown by various techniques. In each of these samples, the so-called violet-pumped Er 3+ PL band and its associated broad violet PLE band are significantly enhanced relative to the PL and PLE of the other selectively excited Er 3+ PL centers. More importantly, the violet-pumped Er 3+ PL spectrum dominates the above-gap excited Er 3+ PL spectrum of Er-implanted Mg-doped GaN, whereas it was unobservable under above-gap excitation in Er-implanted undoped GaN. These results confirm the hypothesis that appropriate codopants can increase the efficiency of trap-mediated above-gap excitation of Er 3+ emission in Er-implanted GaN. [copyright] 2001 American Institute of Physics

  6. The dynamics of a shear band

    Giarola, Diana; Capuani, Domenico; Bigoni, Davide

    2018-03-01

    A shear band of finite length, formed inside a ductile material at a certain stage of a continued homogeneous strain, provides a dynamic perturbation to an incident wave field, which strongly influences the dynamics of the material and affects its path to failure. The investigation of this perturbation is presented for a ductile metal, with reference to the incremental mechanics of a material obeying the J2-deformation theory of plasticity (a special form of prestressed, elastic, anisotropic, and incompressible solid). The treatment originates from the derivation of integral representations relating the incremental mechanical fields at every point of the medium to the incremental displacement jump across the shear band faces, generated by an impinging wave. The boundary integral equations (under the plane strain assumption) are numerically approached through a collocation technique, which keeps into account the singularity at the shear band tips and permits the analysis of an incident wave impinging a shear band. It is shown that the presence of the shear band induces a resonance, visible in the incremental displacement field and in the stress intensity factor at the shear band tips, which promotes shear band growth. Moreover, the waves scattered by the shear band are shown to generate a fine texture of vibrations, parallel to the shear band line and propagating at a long distance from it, but leaving a sort of conical shadow zone, which emanates from the tips of the shear band.

  7. Statistical Model of Extreme Shear

    Hansen, Kurt Schaldemose; Larsen, Gunner Chr.

    2005-01-01

    In order to continue cost-optimisation of modern large wind turbines, it is important to continuously increase the knowledge of wind field parameters relevant to design loads. This paper presents a general statistical model that offers site-specific prediction of the probability density function...... by a model that, on a statistically consistent basis, describes the most likely spatial shape of an extreme wind shear event. Predictions from the model have been compared with results from an extreme value data analysis, based on a large number of full-scale measurements recorded with a high sampling rate...

  8. Generation of sheared poloidal flows by electrostatic and magnetic Reynolds stress in the boundary plasma of HT-7 tokamak

    Xu, G.S.; Wan, B.N.; Li, J.

    2005-01-01

    The radial profiles of electrostatic and magnetic Reynolds stress (Maxwell stress) have been measured in the plasma boundary region of HT-7 tokamak. Experimental results show that the radial gradient of electrostatic Reynolds stress (ERS) changes sign across the last closed flux surface, and the neoclassical flow damping and the damping due to charge exchange processes are balanced by the radial gradient of ERS, which sustains the equilibrium sheared flow structure in a steady state. The contribution of magnetic Reynolds stress was found unimportant in a low β plasma. Detailed analyses indicate that the propagation properties of turbulence in radial and poloidal directions and the profiles of potential fluctuation level are responsible for the radial structure of ERS. (author)

  9. Relative viscosity of emulsions in simple shear flow: Temperature, shear rate, and interfacial tension dependence

    Choi, Se Bin; Lee, Joon Sang [Dept. of Mechanical Engineering, Yonsei Unversity, Seoul (Korea, Republic of)

    2015-08-15

    We simulate an emulsion system under simple shear rates to analyze its rheological characteristics using the lattice Boltzmann method (LBM). We calculate the relative viscosity of an emulsion under a simple shear flow along with changes in temperature, shear rate, and surfactant concentration. The relative viscosity of emulsions decreased with an increase in temperature. We observed the shear-thinning phenomena, which is responsible for the inverse proportion between the shear rate and viscosity. An increase in the interfacial tension caused a decrease in the relative viscosity of the decane-in-water emulsion because the increased deformation caused by the decreased interfacial tension significantly influenced the wall shear stress.

  10. CAMEX-4 ER-2 HIGH ALTITUDE DROPSONDE V1

    National Aeronautics and Space Administration — The CAMEX-4 ER-2 High Altitude Dropsonde dataset was collected by the ER-2 High Altitude Dropsonde System (EHAD), which used dropwinsondes fitted with Global...

  11. CAMEX-4 ER-2 LIGHTNING INSTRUMENT PACKAGE (LIP) V1

    National Aeronautics and Space Administration — The CAMEX-4 ER-2 Lightning Instrument Package (LIP) dataset was collected by the ER-2 LIP, which allows the vector components of the electric field (i.e, Ex, Ey, Ez...

  12. Facets of operational performance in an emergency room (ER)

    van der Vaart, Taco; Vastag, Gyula; Wijngaard, Jacob

    This paper, using detailed time measurements of patients complemented by interviews with hospital management and staff, examines three facets of an emergency room's (ER) operational performance: (1) effectiveness of the triage system in rationing patient treatment; (2) factors influencing ER's

  13. ER Consolidated Qtrly Rpt_April-June 2016_October 2016

    Cochran, John R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-10-01

    This Environmental Restoration Operations (ER) Consolidated Quarterly Report (ER Quarterly Report) provides the status of ongoing corrective action activities being implemented by Sandia National Laboratories, New Mexico (SNL/NM) for the April, May, and June 2016 quarterly reporting period.

  14. GPM Ground Validation Navigation Data ER-2 OLYMPEX V1

    National Aeronautics and Space Administration — The GPM Ground Validation NASA ER-2 Navigation Data OLYMPEX dataset supplies navigation data collected by the NASA ER-2 aircraft for flights that occurred during...

  15. Senior Sport er læring i virkeligheden

    Meyer, Erna Rosenlund

    2014-01-01

    Samarbejde mellem fysioterapeutudddannelsen på UCN og Aalborg senior Sport er givende for alle parter, inklusiv studerende.......Samarbejde mellem fysioterapeutudddannelsen på UCN og Aalborg senior Sport er givende for alle parter, inklusiv studerende....

  16. Predicting Shear Transformation Events in Metallic Glasses

    Xu, Bin; Falk, Michael L.; Li, J. F.; Kong, L. T.

    2018-03-01

    Shear transformation is the elementary process for plastic deformation of metallic glasses, the prediction of the occurrence of the shear transformation events is therefore of vital importance to understand the mechanical behavior of metallic glasses. In this Letter, from the view of the potential energy landscape, we find that the protocol-dependent behavior of shear transformation is governed by the stress gradient along its minimum energy path and we propose a framework as well as an atomistic approach to predict the triggering strains, locations, and structural transformations of the shear transformation events under different shear protocols in metallic glasses. Verification with a model Cu64 Zr36 metallic glass reveals that the prediction agrees well with athermal quasistatic shear simulations. The proposed framework is believed to provide an important tool for developing a quantitative understanding of the deformation processes that control mechanical behavior of metallic glasses.

  17. Shear wall ultimate drift limits

    Duffey, T.A.; Goldman, A.; Farrar, C.R.

    1994-04-01

    Drift limits for reinforced-concrete shear walls are investigated by reviewing the open literature for appropriate experimental data. Drift values at ultimate are determined for walls with aspect ratios ranging up to a maximum of 3.53 and undergoing different types of lateral loading (cyclic static, monotonic static, and dynamic). Based on the geometry of actual nuclear power plant structures exclusive of containments and concerns regarding their response during seismic (i.e.,cyclic) loading, data are obtained from pertinent references for which the wall aspect ratio is less than or equal to approximately 1, and for which testing is cyclic in nature (typically displacement controlled). In particular, lateral deflections at ultimate load, and at points in the softening region beyond ultimate for which the load has dropped to 90, 80, 70, 60, and 50 percent of its ultimate value, are obtained and converted to drift information. The statistical nature of the data is also investigated. These data are shown to be lognormally distributed, and an analysis of variance is performed. The use of statistics to estimate Probability of Failure for a shear wall structure is illustrated

  18. Er frygten for Kina vores eneste håb?

    Mehlsen, Camilla

    2011-01-01

    Man siger, at håbet er lysegrønt, men i det 21. århundrede er håbet rødt som riget i midten. Mens optimismen vinder frem i Asien med Kina som bannerfører, er Vesten ramt af frygt, og det forplanter sig negativt til uddannelsessystemet. Er positive følelser hemmeligheden bag, at asiatiske lande st...... stormer frem i internationale undersøgelser som PISA?...

  19. Shear bond strength of different adhesive systems to normal and caries-affected dentin

    Niloofar Shadman

    2015-10-01

    Full Text Available BACKGROUND AND AIM: According to the effect of the adhesive and substrate type on the bond strength, examination of the adhesive is required in all aspects. The aim of this study was to evaluate the shear bond strength of different adhesive systems to normal dentin (ND and caries affected dentin (CAD in permanent teeth. METHODS: Thirty extracted molars with small occlusal caries were selected. After preparation and determination of ND and CAD by caries detector, teeth were divided into three groups and treated with one of the two tested adhesives: Single Bond 2 (SB2, Scotchbond Universal with etch (SBU-ER, and Scotchbond Universal without etch (SBU-SE. Then composite (Filtek Z-250 XT were attached to the surfaces and cured. After water storage (24 hours and thermocycling (500 cycles 5-55 °C, bond strength was calculated and failure modes were determined by stereomicroscope. The data were analyzed by one-way ANOVA and post-hoc test [Tukey HSD (honest significant difference] and with P ˂ 0.050 as the level of significance. RESULTS: Only SBU-ER had significantly higher shear bond strength than SBU-SE in ND (P = 0.027 and CAD (P = 0.046. Bond strength in SBU-ER the highest and in SBU-SE had the lowest amounts in CAD and ND. There was no significant difference in each group between ND and CAD. CONCLUSION: The 2-step etch-and-rinse adhesive (SBU-ER had higher bond strength to ND and CAD than the selfetch adhesive (SBU-SE.

  20. TCSP ER-2 DOPPLER RADAR (EDOP) V1

    National Aeronautics and Space Administration — The TCSP ER-2 DOPPLER RADAR (EDOP) dataset was collected by the ER-2 Doppler radar (EDOP), which is an X-band (9.6 GHz) Doppler radar mounted in the nose of the ER-2...

  1. CAMEX-4 ER-2 DOPPLER RADAR V1

    National Aeronautics and Space Administration — The CAMEX-4 ER-2 Doppler Radar dataset was collected by the ER-2 Doppler radar (EDOP), which is an X-band (9.6 GHz) Doppler radar mounted in the nose of ER-2. The...

  2. SEC16 in COPII coat dynamics at ER exit sites

    Sprangers, Joep; Rabouille, Catherine

    Protein export from the endoplasmic reticulum (ER), the first step in protein transport through the secretory pathway, is mediated by coatomer protein II (COPII)-coated vesicles at ER exit sites. COPII coat assembly on the ER is well understood and the conserved large hydrophilic protein Sec16

  3. Origins of Shear Jamming for Frictional Grains

    Wang, Dong; Zheng, Hu; Ren, Jie; Dijksman, Joshua; Bares, Jonathan; Behringer, Robert

    2016-11-01

    Granular systems have been shown to be able to behave like solids, under shear, even when their densities are below the critical packing fraction for frictionless isotropic jamming. To understand such a phenomena, called shear jamming, the question we address here is: how does shear bring a system from a unjammed state to a jammed state, where the coordination number, Z, is no less than 3, the isotropic jamming point for frictional grains? Since Z can be used to distinguish jammed states from unjammed ones, it is vital to understand how shear increases Z. We here propose a set of three particles in contact, denoted as a trimer, as the basic unit to characterize the deformation of the system. Trimers, stabilized by inter-grain friction, fail under a certain amount of shear and bend to make extra contacts to regain stability. By defining a projection operator of the opening angle of the trimer to the compression direction in the shear, O, we see a systematically linear decrease of this quantity with respect to shear strain, demonstrating the bending of trimers as expected. In addition, the average change of O from one shear step to the next shows a good collapse when plotted against Z, indicating a universal behavior in the process of shear jamming. We acknowledge support from NSF DMR1206351, NASA NNX15AD38G, the William M. Keck Foundation and a RT-MRSEC Fellowship.

  4. Low-rise shear wall failure modes

    Farrar, C.R.; Hashimoto, P.S.; Reed, J.W.

    1991-01-01

    A summary of the data that are available concerning the structural response of low-rise shear walls is presented. This data will be used to address two failure modes associated with the shear wall structures. First, data concerning the seismic capacity of the shear walls with emphasis on excessive deformations that can cause equipment failure are examined. Second, data concerning the dynamic properties of shear walls (stiffness and damping) that are necessary to compute the seismic inputs to attached equipment are summarized. This case addresses the failure of equipment when the structure remains functional. 23 refs

  5. Magnetic properties of ErGa3

    Murasik, A.; Czopnik, A.; Keller, L.; Fischer, P.

    1999-01-01

    Bulk magnetization measurements and magnetic phase diagram for ErGa 3 show that zero-external magnetic field it undergoes two successive transitions at T 1 = 2.6 K and T 2 = 2.8 K, respectively. Its magnetic ordering examined by neutron diffraction, can be derived from the so-called [1/2, 1/2, 0] structure, i.e. one in which the successive antiparallel (110) sheets of spins have additionally superimposed on them a sinusoidal modulation parallel to the [100] axis. The temperature dependence of neutron diffraction diagrams studied with powder and single crystal samples revealed, that in the range of (2.6 - 2.78) k there occurs an abrupt reorientation of the Er 3+ spins from the [110]-type direction, towards the [100] axis. This rotation can be attributed to the T 1 transition found in the magnetic phase diagram. (author)

  6. SYP73 Anchors the ER to the Actin Cytoskeleton for Maintenance of ER Integrity and Streaming in Arabidopsis.

    Cao, Pengfei; Renna, Luciana; Stefano, Giovanni; Brandizzi, Federica

    2016-12-05

    The endoplasmic reticulum (ER) is an essential organelle that spreads throughout the cytoplasm as one interconnected network of narrow tubules and dilated cisternae that enclose a single lumen. The ER network undergoes extensive remodeling, which critically depends on membrane-cytoskeleton interactions [1]. In plants, the ER is also highly mobile, and its streaming contributes significantly to the movement of other organelles [2, 3]. The remodeling and motility of the plant ER rely mainly on actin [4] and to a minor extent on microtubules [5]. Although a three-way interaction between the ER, cytosolic myosin-XI, and F-actin mediates the plant ER streaming [6], the mechanisms underlying stable interaction of the ER membrane with actin are unknown. Early electron microscopy studies suggested a direct attachment of the plant ER with actin filaments [7, 8], but it is plausible that yet-unknown proteins facilitate anchoring of the ER membrane with the cytoskeleton. We demonstrate here that SYP73, a member of the plant Syp7 subgroup of SNARE proteins [9] containing actin-binding domains, is a novel ER membrane-associated actin-binding protein. We show that overexpression of SYP73 causes a striking rearrangement of the ER over actin and that, similar to mutations of myosin-XI [4, 10, 11], loss of SYP73 reduces ER streaming and affects overall ER network morphology and plant growth. We propose a model for plant ER remodeling whereby the dynamic rearrangement and streaming of the ER network depend on the propelling action of myosin-XI over actin coupled with a SYP73-mediated bridging, which dynamically anchors the ER membrane with actin filaments. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Virtual Reality er dit nye Skype

    Bødker, Mads

    2016-01-01

    VR er mediet, der kan gøre den flade skærm og det begrænsede blik i for eksempel Skype til et lidt gammeldags digitalt samarbejde. Ved at sætte folk i stand til at kommunikere, dele virtuelle genstande og give dem en øget oplevelse af at være i et rum sammen, kan man mediere nye aspekter af samar...

  8. Her er din motion i 2012

    Suhr, Lasse Kristian

    2014-01-01

    Motion i naturen, en indendørs fitnessform inspireret af junglens lianer og høj intensitet med crossfit. Det er ifølge en ekspert nogle af de træningstyper, der vil være mest populære i 2012. Året hvor fleksibilitet og frihed vil blive endnu vigtigere, for den måde vi holder os i form på....

  9. Selskaberne er en del af staten

    Hein Jessen, Mathias

    2016-01-01

    Lækket af Panama Papers fremhæver endnu engang den paradoksale rolle, ikke mindst multinationale selskaber spiller i politik og økonomi: De er både skabt af staten, og fremstår stadig som uden for og i opposition til staten. Hvis vi vil gøre noget ved problemet, må vi forstå, hvordan stat og...

  10. Hamlet er manden i mit liv

    Rösing, Lilian Munk

    2009-01-01

    Hamlet er manden i mit liv. Min elskede. Jeg har en drøm om at frelse ham. At redde ham ud af sin mors soveværelse og ind i mit. Væk fra det ødipale Helvede han befinder sig i, fastlåst mellem et svin af en faderskikkelse (Claudius) og en alt for idealiseret far (gamle Hamlet), vågende over sin m...

  11. Musikkens Hus i Aalborg er demensvenligt

    Ridder, Hanne Mette Ochsner

    2017-01-01

    . Der blev afholdt frokostmøder hvor medarbejdere og brugere af Musikkens Hus fik undervisning om demens. Der blev også udvekslet gode idéer til hvad man i Musikkens Hus kan gøre for at byde mennesker med demens velkomne. at vi skal læse en masse, gå på kurser eller forpligte os til at være besøgsven...

  12. ER-12-1 completion report

    Russell, C.E.; Gillespie, D.; Cole, J.C.; Drellack, S.L.

    1996-12-01

    The objective of drillhole ER-12-1 was to determine the hydrogeology of paleozoic carbonate rocks and of the Eleana Formation, a regional aquitard, in an area potentially downgradient from underground nuclear testing conducted in nearby Rainier Mesa. This objective was addressed through the drilling of well ER-12-1 at N886,640.26 E640,538.85 Nevada Central Coordinates. Drilling of the 1094 m (3588 ft) well began on July 19, 1991 and was completed on October 17, 1991. Drilling problems included hole deviation and hole instability that prevented the timely completion of this borehole. Drilling methods used include rotary tri-cone and rotary hammer drilling with conventional and reverse circulation using air/water, air/foam (Davis mix), and bentonite mud. Geologic cuttings and geophysical logs were obtained from the well. The rocks penetrated by the ER-12-1 drillhole are a complex assemblage of Silurian, Devonian, and Mississippian sedimentary rocks that are bounded by numerous faults that show substantial stratigraphic offset. The final 7.3 m (24 ft) of this hole penetrated an unusual intrusive rock of Cretaceous age. The geology of this borehole was substantially different from that expected, with the Tongue Wash Fault encountered at a much shallower depth, paleozoic rocks shuffled out of stratigraphic sequence, and the presence of an altered biotite-rich microporphyritic igneous rock at the bottom of the borehole. Conodont CAI analyses and rock pyrolysis analyses indicate that the carbonate rocks in ER-12-1, as well as the intervening sheets of Eleana siltstone, have been thermally overprinted following movement on the faults that separate them. The probable source of heat for this thermal disturbance is the microporphyritic intrusion encountered at the bottom of the hole, and its age establishes that the major fault activity must have occurred prior to 102.3+0.5 Ma (middle Cretaceous)

  13. Friluftsinstallationer i træer

    Skov, Simon; Thomsen, Iben Margrete

    2015-01-01

    Abebaner, treetop walking, high rope adventure, slackline, træhuse og parkour-baner er alle installationer, som bruger træerne som støtte, enten midlertidigt eller permanent. Den nye sport, turistattraktionen eller team building-redskabet sætter i alle tilfælde træerne på prøve. Der følger positiv...

  14. The role of the AR/ER ratio in ER-positive breast cancer patients.

    Rangel, Nelson; Rondon-Lagos, Milena; Annaratone, Laura; Osella-Abate, Simona; Metovic, Jasna; Mano, Maria Piera; Bertero, Luca; Cassoni, Paola; Sapino, Anna; Castellano, Isabella

    2018-03-01

    The significance of androgen receptor (AR) in breast cancer (BC) management is not fully defined, and it is still ambiguous how the level of AR expression influences oestrogen receptor-positive (ER+) tumours. The aim of the present study was to analyse the prognostic impact of AR/ER ratio, evaluated by immunohistochemistry (IHC), correlating this value with clinical, pathological and molecular characteristics. We retrospectively selected a cohort of 402 ER+BC patients. On each tumour, IHC analyses for AR, ER, PgR, HER2 and Ki67 were performed and AR+ cases were used to calculate the AR/ER value. A cut-off of ≥2 was selected using receiver-operating characteristic (ROC) curve analyses. RNA from 19 cases with AR/ER≥2 was extracted and used for Prosigna-PAM50 assays. Tumours with AR/ER≥2 (6%) showed more frequent metastatic lymph nodes, larger size, higher histological grade and lower PgR levels than cases with AR/ERAR/ER≥2 had worse disease-free interval (DFI) and disease-specific survival (DSS) (hazard ratios (HR) = 4.96 for DFI and HR = 8.69 for DSS, both P  ≤ 0.004). According to the Prosigna-PAM50 assay, 63% (12/19) of these cases resulted in intermediate or high risk of recurrence categories. Additionally, although all samples were positive for ER assessed by IHC, the molecular test assigned 47.4% (9/19) of BCs to intrinsic non-luminal subtypes. In conclusion, the AR/ER ratio ≥2 identifies a subgroup of patients with aggressive biological features and may represent an additional independent marker of worse BC prognosis. Moreover, the Prosigna-PAM50 results indicate that a significant number of cases with AR/ER≥2 could be non-luminal tumours. © 2018 Society for Endocrinology.

  15. Shear thinning behaviors in magmas

    Vetere, F. P.; Cassetta, M.; Perugini, D.

    2017-12-01

    Studies on magma rheology are of fundamental importance to understanding magmatic processes from depth to surface. Since viscosity is one of the most important parameter controlling eruption mechanisms, as well as lava flow emplacement, a comprehensive knowledge on the evolution of magma viscosities during crystallization is required. We present new viscosity data on partly crystalized basalt, andesite and analogue lavas comparable to those erupted on Mercury's northern volcanic plains. High-temperature viscosity measurements were performed using a rotational Anton Paar RheolabQC viscometer head at the PVRG labs, in Perugia (Italy) (http://pvrg.unipg.it). The relative proportion of phases in each experimental run were determined by image analysis on BS-SEM images at different magnifications; phases are glasses, clinopyroxene, spinel, plagioclase for the basalt, plagioclase and spinel for the andesite and pure enstatite and clinopyroxenes, for the analogue Mercury's composition. Glass and crystalline fractions determined by image analysis well correlate with compositions of residual melts. In order to constrain the viscosity (η) variations as a function of crystallinity, shear rate (γ) was varied from 0.1 to 5 s-1. Viscosity vs. time at constant temperature shows a typical S-shape curve. In particular, for basaltic composition η vary from 3.1-3.8 Pa s [log η] at 1493 K and crystallinity of 19 area % as γ vary from 1.0 to 0.1 s-1; the andesite viscosity evolution is 3.2 and 3.7 Pa s [log η] as γ varies from 1 to 0.1 at 1493 K and crystal content of 17 area %; finally, Mercury's analogue composition was investigated at different temperature ranging from 1533 to 1502 K (Vetere et al., 2017). Results, for γ = 0.1, 1.0 and 5.0 s-1, show viscosity variation between 2.7-4.0, 2.5-3.4 and 2.0-3.0 [log η inPa s] respectively while crystallinity vary from 9 to 27 (area %). As viscosity decreases as shear rate increases, these data points to a shear thinning behaviour

  16. ER stress, autophagy, and RNA viruses

    Jia-Rong eJheng

    2014-08-01

    Full Text Available Endoplasmic reticulum (ER stress is a general term for representing the pathway by which various stimuli affect ER functions. ER stress induces the evolutionarily conserved signaling pathways, called the unfolded protein response (UPR, which compromises the stimulus and then determines whether the cell survives or dies. In recent years, ongoing research has suggested that these pathways may be linked to the autophagic response, which plays a key role in the cell’s response to various stressors. Autophagy performs a self-digestion function, and its activation protects cells against certain pathogens. However, the link between the UPR and autophagy may be more complicated. These two systems may act dependently, or the induction of one system may interfere with the other. Experimental studies have found that different viruses modulate these mechanisms to allow them to escape the host immune response or, worse, to exploit the host’s defense to their advantage; thus, this topic is a critical area in antiviral research. In this review, we summarize the current knowledge about how RNA viruses, including influenza virus, poliovirus, coxsackievirus, enterovirus 71, Japanese encephalitis virus, hepatitis C virus, and dengue virus, regulate these processes. We also discuss recent discoveries and how these will produce novel strategies for antiviral treatment.

  17. Sund livsstil er mere end fysik

    Nybo, Lars; Thing, Lone Friis; Astrup, Arne

    2015-01-01

    . I virkeligheden hænger tingene sammen, og i et holistisk sundhedsbillede er de psykiske og sociale dimensioner mindst lige så vigtige som de fysiske. Fællesskabet under og efter fodboldtræningen kan for eksempel være en lige så vigtig del af at være aktiv som selve træningen. Og selv om nogle...... begynder på en aktiv livsstil ud fra en ydre motivation om det fysiske aspekt af ’mere sundhed’, så er der meget, som tyder på, at den indre motivation overtager, og at de i stedet bliver drevet af glæden ved den øgede livskvalitet. Nogle mennesker fascineres af at følge en fast træningsplan og have et...... behandling af inaktivitetsrelaterede lidelser bør dog ikke være det vigtigste argument for at oplyse om og opfordre til en sund livsstil. Livskvalitetsaspektet skal være i højsædet, og det er for så vidt en legitim bekymring, at der kommer et overdrevet fokus på samfundsøkonomi og forebyggelse af somatisk...

  18. Comparison of direct shear and simple shear responses of municipal solid waste in USA

    Fei, Xunchang; Zekkos, Dimitrios

    2017-01-01

    Although large-size simple shear (SS) testing of municipal solid waste (MSW) may arguably provide a more realistic estimate of the shear strength (τ ) of MSW than the most commonly used direct shear (DS) testing, a systematic comparison between

  19. Turbulence suppression by E x B shear in JET optimized shear pulses

    Beer, M.A.; Budny, R.V.; Challis, C.D.; Conway, G.

    2000-01-01

    The authors calculate microinstability growth rates in JET optimized shear plasmas with a comprehensive gyrofluid model, including sheared E x B flows, trapped electrons, and all dominant ion species in realistic magnetic geometry. They find good correlation between E x B shear suppression of microinstabilities and both the formation and collapse of the internal transport barrier

  20. The structure of the 168Er nucleus and the 166Er(t,p) 168 Er reaction in terms of the sdg interacting boson model

    Akiyama, Y.; Heyde, K.; Arima, A.; Yoshinaga, N.

    1986-05-01

    Extending the interacting boson model by incorporating besides s and d, also the g-boson, we can describe the population of positive parity states of 168Er in the 166Er(t,P) 168Er reaction rather well. In particular, the excitation of I,Kπi = 4,3 +1; 2,2 +2; 0,0 +3 and 0,0 +4 states is much improved over the sd-IBM approach.

  1. MicroRNAs meet calcium: joint venture in ER proteostasis.

    Finger, Fabian; Hoppe, Thorsten

    2014-11-04

    The endoplasmic reticulum (ER) is a cellular compartment that has a key function in protein translation and folding. Maintaining its integrity is of fundamental importance for organism's physiology and viability. The dynamic regulation of intraluminal ER Ca(2+) concentration directly influences the activity of ER-resident chaperones and stress response pathways that balance protein load and folding capacity. We review the emerging evidence that microRNAs play important roles in adjusting these processes to frequently changing intracellular and environmental conditions to modify ER Ca(2+) handling and storage and maintain ER homeostasis. Copyright © 2014, American Association for the Advancement of Science.

  2. Vidensledelse er også en social praksis

    Lauring, Jakob; Waldstrøm, Christian

    2006-01-01

    lys er det utroligt vigtigt at personalefunktionen i virksomheden er klar over de processer der udspiller sig, og aktivt tager fat om problemerne der ligger i disse barrierer. Vores egne undersøgelser viser, at på trods af opstillingen af teknologiske systemer til vidensdeling, er der stadig...... væsentlige ledelsesmæssige opgaver i forhold til sociale aspekter ved arbejdet i en organisation, som skal varetages hvis vidensdelingen skal fremmes succesfuldt. Det er væsentligt at forstå, at vidensledelse ikke blot handler om cirkulering af information, men også er forbundet mere generelt til ledelse som...

  3. Tensile and shear strength of adhesives

    Stibolt, Kenneth A.

    1990-01-01

    This experiment is conducted in a freshman-level course: Introduction to Engineering Materials. There are no prerequisites for the course although students should have some knowledge of basic algebra. The objectives are to tension and shear test adhesives and to determine the tensile and shear properties of adhesives. Details of equipment of procedure are given.

  4. Crosswind Shear Gradient Affect on Wake Vortices

    Proctor, Fred H.; Ahmad, Nashat N.

    2011-01-01

    Parametric simulations with a Large Eddy Simulation (LES) model are used to explore the influence of crosswind shear on aircraft wake vortices. Previous studies based on field measurements, laboratory experiments, as well as LES, have shown that the vertical gradient of crosswind shear, i.e. the second vertical derivative of the environmental crosswind, can influence wake vortex transport. The presence of nonlinear vertical shear of the crosswind velocity can reduce the descent rate, causing a wake vortex pair to tilt and change in its lateral separation. The LES parametric studies confirm that the vertical gradient of crosswind shear does influence vortex trajectories. The parametric results also show that vortex decay from the effects of shear are complex since the crosswind shear, along with the vertical gradient of crosswind shear, can affect whether the lateral separation between wake vortices is increased or decreased. If the separation is decreased, the vortex linking time is decreased, and a more rapid decay of wake vortex circulation occurs. If the separation is increased, the time to link is increased, and at least one of the vortices of the vortex pair may have a longer life time than in the case without shear. In some cases, the wake vortices may never link.

  5. Shear stresses around circular cylindrical openings

    Hoogenboom, P.C.J.; Van Weelden, C.; Blom, C.M.B.

    2010-01-01

    In this paper stress concentrations are studied around circular cylindrical openings or voids in a linear elastic continuum. The loading is such that a uniform shear stress occurs in the continuum, which is disturbed by the opening. The shear stress is in the direction of the centre axis of the

  6. Simulations of biopolymer networks under shear

    Huisman, Elisabeth Margaretha

    2011-01-01

    In this thesis we present a new method to simulate realistic three-dimensional networks of biopolymers under shear. These biopolymer networks are important for the structural functions of cells and tissues. We use the method to analyze these networks under shear, and consider the elastic modulus,

  7. Rating precast prestressed concrete bridges for shear

    2008-12-01

    Shear capacity of real-world prestressed concrete girders designed in the 1960s and 1970s is a concern because : AASHTO Standard Specifications (AASHTO-STD) employed the quarter-point rule for shear design, which is less : conservative for shea...

  8. Æstetik er tilbage som nøgle til at forstå samtiden

    Sharma, Devika

    2013-01-01

    Casper Christensen er gakket, Hello Kitty er nuttet og konceptkunsten er interessant. Her er tre nye kategorier at forstå senkapitalismen med. I anledning af Sianne Ngais bog "Our aesthetic categories: zany, cute, interesting" .......Casper Christensen er gakket, Hello Kitty er nuttet og konceptkunsten er interessant. Her er tre nye kategorier at forstå senkapitalismen med. I anledning af Sianne Ngais bog "Our aesthetic categories: zany, cute, interesting" ....

  9. Friction of Shear-Fracture Zones

    Riikilä, T. I.; Pylväinen, J. I.; Åström, J.

    2017-12-01

    A shear fracture of brittle solids under compression undergoes a substantial evolution from the initial microcracking to a fully formed powder-filled shear zone. Experiments covering the entire process are relatively easy to conduct, but they are very difficult to investigate in detail. Numerically, the large strain limit has remained a challenge. An efficient simulation model and a custom-made experimental device are employed to test to what extent a shear fracture alone is sufficient to drive material to spontaneous self-lubrication. A "weak shear zone" is an important concept in geology, and a large number of explanations, specific for tectonic conditions, have been proposed. We demonstrate here that weak shear zones are far more general, and that their emergence only demands that a microscopic, i.e., fragment-scale, stress relaxation mechanism develops during the fracture process.

  10. Imaging Shear Strength Along Subduction Faults

    Bletery, Quentin; Thomas, Amanda M.; Rempel, Alan W.; Hardebeck, Jeanne L.

    2017-11-01

    Subduction faults accumulate stress during long periods of time and release this stress suddenly, during earthquakes, when it reaches a threshold. This threshold, the shear strength, controls the occurrence and magnitude of earthquakes. We consider a 3-D model to derive an analytical expression for how the shear strength depends on the fault geometry, the convergence obliquity, frictional properties, and the stress field orientation. We then use estimates of these different parameters in Japan to infer the distribution of shear strength along a subduction fault. We show that the 2011 Mw9.0 Tohoku earthquake ruptured a fault portion characterized by unusually small variations in static shear strength. This observation is consistent with the hypothesis that large earthquakes preferentially rupture regions with relatively homogeneous shear strength. With increasing constraints on the different parameters at play, our approach could, in the future, help identify favorable locations for large earthquakes.

  11. Thrombus Formation at High Shear Rates.

    Casa, Lauren D C; Ku, David N

    2017-06-21

    The final common pathway in myocardial infarction and ischemic stroke is occlusion of blood flow from a thrombus forming under high shear rates in arteries. A high-shear thrombus forms rapidly and is distinct from the slow formation of coagulation that occurs in stagnant blood. Thrombosis at high shear rates depends primarily on the long protein von Willebrand factor (vWF) and platelets, with hemodynamics playing an important role in each stage of thrombus formation, including vWF binding, platelet adhesion, platelet activation, and rapid thrombus growth. The prediction of high-shear thrombosis is a major area of biofluid mechanics in which point-of-care testing and computational modeling are promising future directions for clinically relevant research. Further research in this area will enable identification of patients at high risk for arterial thrombosis, improve prevention and treatment based on shear-dependent biological mechanisms, and improve blood-contacting device design to reduce thrombosis risk.

  12. Experimental study on the adiabatic shear bands

    Affouard, J.

    1984-07-01

    Four martensitic steels (Z50CDV5 steel, 28CND8 steel, 35NCDV16 steel and 4340 steel) with different hardness between 190 and 600 Hsub(B) (Brinell hardness), have been studied by means of dynamic compressive tests on split Hopkinson pressure bar. Microscopic observations show that the fracture are associated to the development of adiabatic shear bands (except 4340 steel with 190 Hsub(B) hardness). By means of tests for which the deformation is stopped at predetermined levels, the measurement of shear and hardness inside the band and the matrix indicates the chronology of this phenomenon: first the localization of shear, followed by the formation of adiabatic shear band and ultimatly crack initiation and propagation. These results correlated with few simulations by finite elements have permitted to suggest two mecanisms of deformation leading to the formation of adiabatic shear bands in this specific test [fr

  13. Imaging shear strength along subduction faults

    Bletery, Quentin; Thomas, Amanda M.; Rempel, Alan W.; Hardebeck, Jeanne L.

    2017-01-01

    Subduction faults accumulate stress during long periods of time and release this stress suddenly, during earthquakes, when it reaches a threshold. This threshold, the shear strength, controls the occurrence and magnitude of earthquakes. We consider a 3-D model to derive an analytical expression for how the shear strength depends on the fault geometry, the convergence obliquity, frictional properties, and the stress field orientation. We then use estimates of these different parameters in Japan to infer the distribution of shear strength along a subduction fault. We show that the 2011 Mw9.0 Tohoku earthquake ruptured a fault portion characterized by unusually small variations in static shear strength. This observation is consistent with the hypothesis that large earthquakes preferentially rupture regions with relatively homogeneous shear strength. With increasing constraints on the different parameters at play, our approach could, in the future, help identify favorable locations for large earthquakes.

  14. Suppression of concentration quenching of Er-related luminescence in Er-doped GaN

    Chen Shaoqiang; Tomita, Shigeo; Kudo, Hiroshi; Akimoto, Katsuhiro; Dierre, Benjamin; Lee, Woong; Sekiguchi, Takashi

    2010-01-01

    Erbium-doped GaN with different doping concentrations were grown by ammonia-source molecular beam epitaxy. The intra-4f-shell transitions related green luminescence were observed by both photoluminescence (PL) and cathodoluminescence (CL) measurements. It was found that concentration quenching of Er-related luminescence was observed in PL measurements while not in CL measurements. The different excitation and relaxation processes are suggested as the cause of the concentration quenching characteristics between PL and CL. The strong Er-related CL intensity in highly doped GaN demonstrates that high energy excitation is a promising approach to suppress the concentration quenching in Er-doped GaN.

  15. Interlayer exchange coupling in Er|Tb superlattices mediated by short range incommensurate Er order

    Pfuhl, E; Brueckel, T; Voigt, J; Mattauch, S; Korolkov, D

    2010-01-01

    We study the magnetic correlations in Er|Tb superlattices by means of off-specular scattering of polarized neutrons. We show here the co-existence of inhomogeneous magnetic states: i) ferromagnetic order of moments within the Tb layers below 230 K (FM), correlation length of about 10 bilayer, ii) an incommensurate modulated magnetic order, restricted to single Er layers and iii) antiferromagnetic coupling of ferromagnetic layers below 70K (AFC). Polarised off-specular neutron scattering under grazing incidence reveals that i) magnetic fluctuations appear when the sample is cooled below 70 K, ii) these fluctuations lead to AFC, when the sample is cooled to 10 K, which iii) persists, when the sample is subsequently heated up to 45 K, while the order is not present during the cooling cycle. Also the short range incommensurate order changes accordingly, implying that the magnetic order in the Er layers mediates the interlayer coupling between ferromagnetic Tb layers.

  16. Fracture Toughness and Shear Strength of the Bonded Interface Between an Aluminium Alloy Skin and a FRP Patch

    Kumar, Prashant; Shinde, Prakash Sonyabapu; Bhoyar, Gaurav

    2018-05-01

    The existing techniques to determine the fracture properties such as critical energy release rate in mode I (GIc) and mode II (GIIc) of an interface between two sheets of same material were modified to determine these properties between the sheets of dissimilar materials and thickness. In addition, the interface shear strength (ISS) was also determined. Experiments were carried out on the specimens made of a pre-cracked thin aluminium alloy skin and a Fiber reinforced polymer (FRP) patch. Two kinds of surface preparation of the aluminium skin were employed; (i) emery-paper roughened surface (ERS) and (ii) Sodium Hydroxide (NaOH) treated surface (NTS). GIc of ERS specimen was found to be 36.1 J/m2, while it was found to be much higher for NTS specimens, that is, 87.3 J/m2. GIIc was found to be 282.4 J/m2 for ERS specimens and much higher as 734.5 J/m2 for NTS specimens. ISS was determined as 32.6 MPa for ERS specimen and significantly higher for NTS specimen, that is, 44.5 MPa. The micrographs obtained from a field emission-scanning electron microscope (FE-SEM) and the surface roughness test showed that the NTS was significantly rougher than the ERS, explaining the higher values of all the three kinds of NTS specimens.

  17. Effect of the unfolded protein response on ER protein export: a potential new mechanism to relieve ER stress.

    Shaheen, Alaa

    2018-05-05

    The unfolded protein response (UPR) is an adaptive cellular response that aims to relieve endoplasmic reticulum (ER) stress via several mechanisms, including inhibition of protein synthesis and enhancement of protein folding and degradation. There is a controversy over the effect of the UPR on ER protein export. While some investigators suggested that ER export is inhibited during ER stress, others suggested the opposite. In this article, their conflicting studies are analyzed and compared in attempt to solve this controversy. The UPR appears indeed to enhance ER export, possibly via multiple mechanisms. However, another factor, which is the integrity of the folding machinery/environment inside ER, determines whether ER export will appear increased or decreased during experimentation. Also, different methods of stress induction appear to have different effects on ER export. Thus, improvement of ER export may represent a new mechanism by which the UPR alleviates ER stress. This may help researchers to understand how the UPR works inside cells and how to manipulate it to alter cell fate during stress, either to promote cell survival or death. This may open up new approaches for the treatment of ER stress-related diseases.

  18. On the Use of an ER-213 Detonator to Establish a Baseline for the ER-486

    Thomas, Keith A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Liechty, Gary H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jaramillo, Dennis C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Munger, Alan C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); McHugh, Douglas C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kennedy, James E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-08-19

    This report documents a series of tests using a TSD-115 fireset coupled with an ER-213, a gold exploding bridgewire (EBW) detonator. These tests were designed to fire this EBW with a smaller fireset to obtain current and voltage data as well as timing information at voltage levels below, above, and throughout the threshold firing region. This study could then create a database for comparison to our current ER-486 EBW development, which is designed to be a lower voltage (<500V) device.

  19. Core-Shell Structured Electro- and Magneto-Responsive Materials: Fabrication and Characteristics

    Hyoung Jin Choi

    2014-11-01

    Full Text Available Core-shell structured electrorheological (ER and magnetorheological (MR particles have attracted increasing interest owing to their outstanding field-responsive properties, including morphology, chemical and dispersion stability, and rheological characteristics of shear stress and yield stress. This study covers recent progress in the preparation of core-shell structured materials as well as their critical characteristics and advantages. Broad emphasises from the synthetic strategy of various core-shell particles to their feature behaviours in the magnetic and electric fields have been elaborated.

  20. GR and ER co-activation alters the expression of differentiation genes and associates with improved ER+ breast cancer outcome

    West, Diana C.; Pan, Deng; Tonsing-Carter, Eva Y.; Hernandez, Kyle M.; Pierce, Charles F.; Styke, Sarah C.; Bowie, Kathleen R.; Garcia, Tzintzuni I.; Kocherginsky, Masha; Conzen, Suzanne D.

    2016-01-01

    In estrogen receptor (ER)-negative breast cancer (BC), high tumor glucocorticoid receptor (GR) expression has been associated with a relatively poor outcome. In contrast, using a meta-analysis of several genomic datasets, here we find that tumor GR mRNA expression is associated with improved ER+ relapse-free survival (RFS) (independently of progesterone receptor (PR) expression). To understand the mechanism by which GR expression is associated with a better ER+ BC outcome, the global effect of GR-mediated transcriptional activation in ER+ BC cells was studied. Analysis of GR chromatin immunoprecipitation followed by high-throughput sequencing (ChIP-seq) in ER+/GR+ MCF-7 cells revealed that upon co-activation of GR and ER, GR chromatin association became enriched at proximal promoter regions. Furthermore, following ER activation, increased GR chromatin association was observed at ER, FOXO, and AP1 response elements. In addition, ER associated with GR response elements, suggesting that ER and GR interact in a complex. Co-activation of GR and ER resulted in increased expression (relative to ER activation alone) of transcripts that encode proteins promoting cellular differentiation (e.g. KDM4B, VDR) and inhibiting the Wnt-signaling pathway (IGFBP4). Finally, expression of these individual pro-differentiation genes was associated with significantly improved RFS in ER+ BC patients. Together, these data suggest that the co-expression and subsequent activity of tumor cell GR and ER contribute to the less aggressive natural history of early-stage BC by coordinating the altered expression of genes favoring differentiation. Implications The interaction between estrogen and glucocorticoid receptor activity highlights the importance of context-dependent nuclear receptor function in cancer. PMID:27141101

  1. COPII-Dependent ER Export: A Critical Component of Insulin Biogenesis and β-Cell ER Homeostasis.

    Fang, Jingye; Liu, Ming; Zhang, Xuebao; Sakamoto, Takeshi; Taatjes, Douglas J; Jena, Bhanu P; Sun, Fei; Woods, James; Bryson, Tim; Kowluru, Anjaneyulu; Zhang, Kezhong; Chen, Xuequn

    2015-08-01

    Pancreatic β-cells possess a highly active protein synthetic and export machinery in the endoplasmic reticulum (ER) to accommodate the massive production of proinsulin. ER homeostasis is vital for β-cell functions and is maintained by the delicate balance between protein synthesis, folding, export, and degradation. Disruption of ER homeostasis by diabetes-causing factors leads to β-cell death. Among the 4 components to maintain ER homeostasis in β-cells, the role of ER export in insulin biogenesis is the least understood. To address this knowledge gap, the present study investigated the molecular mechanism of proinsulin ER export in MIN6 cells and primary islets. Two inhibitory mutants of the secretion-associated RAS-related protein (Sar)1 small GTPase, known to specifically block coat protein complex II (COPII)-dependent ER export, were overexpressed in β-cells using recombinant adenoviruses. Results from this approach, as well as small interfering RNA-mediated Sar1 knockdown, demonstrated that defective Sar1 function blocked proinsulin ER export and abolished its conversion to mature insulin in MIN6 cells, isolated mouse, and human islets. It is further revealed, using an in vitro vesicle formation assay, that proinsulin was packaged into COPII vesicles in a GTP- and Sar1-dependent manner. Blockage of COPII-dependent ER exit by Sar1 mutants strongly induced ER morphology change, ER stress response, and β-cell apoptosis. These responses were mediated by the PKR (double-stranded RNA-dependent kinase)-like ER kinase (PERK)/eukaryotic translation initiation factor 2α (p-eIF2α) and inositol-requiring protein 1 (IRE1)/x-box binding protein 1 (Xbp1) pathways but not via activating transcription factor 6 (ATF6). Collectively, results from the study demonstrate that COPII-dependent ER export plays a vital role in insulin biogenesis, ER homeostasis, and β-cell survival.

  2. Hvor langt er PISA fra Danmark?

    Dolin, Jens; Krogh, Lars Brian

    2008-01-01

    PISA 2006 science testen i en dansk kontekst. I det første delprojekt sammenlignes PISA science frameworket med de danske mål for naturfagsuddannelserne. I det andet delprojekt undersøges hvorledes PISA testformatet er i overensstemmelse med evalueringspraksis i naturfagene i den danske folkeskole. I...... det tredje delprojekt sammenlignes elevers score i PISA science testen med deres resultater i en mere dialogbaseret evalueringssituation.   De tre delundersøgelser betjener sig af forskellige metoder, nemlig henholdsvis tekstanalyse, spørgeskemaundersøgelse/ interview samt en egentlig feltvalidering...

  3. BOREAS Level-0 ER-2 Navigation Data

    Strub, Richard; Dominguez, Roseanne; Newcomer, Jeffrey A.; Hall, Forrest G. (Editor)

    2000-01-01

    The BOREAS Staff Science effort covered those activities that were BOREAS community-level activities or required uniform data collection procedures across sites and time. These activities included the acquisition, processing, and archiving of aircraft navigation/attitude data to complement the digital image data. The level-0 ER-2 navigation data files contain aircraft attitude and position information acquired during the digital image and photographic data collection missions. Temporally, the data were acquired from April to September 1994. Data were recorded at intervals of 5 seconds. The data are stored in tabular ASCII files.

  4. Photoluminescence of Er in SiOx

    Wan Jun; Sheng Chi; Lu Fang; Gong Dawei; Fan Yongliang; Lin Feng; Wang Xun

    1998-01-01

    Erbium-doped SiO x is prepared by molecular beam epitaxy. The influence of Er on the incorporation of O is studied by using Auger spectroscopy. Photoluminescence (PL) peaks around the wave-length of 1.53 μm have been observed within the temperature range of 18 to 300 K after annealing. The relationship between PL intensity and annealing temperature is discussed. The temperature dependence of the PL intensity shows an exponential decay with an activation energy of 12 meV at low temperatures ( 100 K)

  5. Investigation de fluides électrorhéologiques sur la base des matériaux hybrides

    Marins , Jéssica Alves ,

    2014-01-01

    Electrorheology is an area has been exploring the application of these organic-inorganic hybrid compounds, to obtain better performance in electrorheological properties. Electro-rheological fluids consist of a colloidal dispersion, where the liquid is non-conductive and the particles dispersed in the fluid are able of polarized at presence of electric field. When the fluids ER are subjected to an external electric field the rheological properties change, and may increase or decrease the appar...

  6. IMAGE ANALYSIS FOR MODELLING SHEAR BEHAVIOUR

    Philippe Lopez

    2011-05-01

    Full Text Available Through laboratory research performed over the past ten years, many of the critical links between fracture characteristics and hydromechanical and mechanical behaviour have been made for individual fractures. One of the remaining challenges at the laboratory scale is to directly link fracture morphology of shear behaviour with changes in stress and shear direction. A series of laboratory experiments were performed on cement mortar replicas of a granite sample with a natural fracture perpendicular to the axis of the core. Results show that there is a strong relationship between the fracture's geometry and its mechanical behaviour under shear stress and the resulting damage. Image analysis, geostatistical, stereological and directional data techniques are applied in combination to experimental data. The results highlight the role of geometric characteristics of the fracture surfaces (surface roughness, size, shape, locations and orientations of asperities to be damaged in shear behaviour. A notable improvement in shear understanding is that shear behaviour is controlled by the apparent dip in the shear direction of elementary facets forming the fracture.

  7. Er:YAG pre-treatment for bonding of orthodontic bracket: 1 year of in vitro treatment

    de Jesus Tavarez RR

    2017-03-01

    Full Text Available Rudys Rodolfo de Jesus Tavarez,1 Gisele Lima Bezerra,2 Karla Janilee de Souza Penha,3 Carlos Rocha Gomes Torres,4 Leily Macedo Firoozmand5 1Department of Dentistry, Ceuma University (UNICEUMA, 2Dentistry Program, Ceuma University (UNICEUMA, 3Dentistry Program, Federal University of Maranhão, UFMA, São Luís, MA, 4Restorative Dentistry Department, ICT UNESP University, São Paulo, 5Dentistry Department I, Federal University of Maranhão,UFMA, São Luís, MA, Brazil Objective: The aim of this study was to evaluate in vitro bond strength of metal brackets bonded with: total etch, total etch with erbium: yttrium aluminum garnet laser (Er:YAG and self-etching adhesive systems, submitted to thermal-mechanical cycling, simulating 1 year of orthodontic treatment.Materials and methods: For the study, 80 bovine incisors were randomly divided into 3 experimental groups (n=16 each: XT- acid etching + Transbond XT, XT/Er:YAG- Transbond XT associated with Er:YAG laser irradiation (λ=2.94 μm, 60 mJ, 10 Hz and SEP- Transbond Plus Self Etching Primer. Samples were submitted to thermal-mechanical cycling, simulating 1 year of orthodontic treatment. Afterward, the shear bond strength test was performed in a universal test machine at a speed of 0.5mm/min. Samples were evaluated under a stereomicroscope and by scanning electron microscopy for analysis of enamel surface and adhesive remnant index. Data were analyzed using Kruskal–Wallis and Mann–Whitney (with Bonferroni correction statistical tests.Results: Statistically significant difference was observed between the groups studied (p<0.05. Groups XT and SEP showed the highest bond strength values, without statistical difference between them, while group XT/Er:YAG showed reduction in bond strength values. Higher frequency of adhesive failures between enamel and adhesive system was verified for groups XT and XT/Er:YAG.Conclusion: The conventional (XT and self-etching (SEP adhesive systems showed mean bond

  8. Effects of Different Combinations of Er:YAG Laser-Adhesives on Enamel Demineralization and Bracket Bond Strength.

    Çokakoğlu, Serpil; Nalçacı, Ruhi; Üşümez, Serdar; Malkoç, Sıddık

    2016-04-01

    The purpose of this study was to investigate the demineralization around brackets and shear bond strength (SBS) of brackets bonded to Er:YAG laser-irradiated enamel at different power settings with various adhesive systems combinations. A total of 108 premolar teeth were used in this study. Teeth were assigned into three groups according to the etching procedure, then each group divided into three subgroups based on the application of different adhesive systems. There were a total of nine groups as follows. Group 1: Acid + Transbond XT Primer; group 2: Er:YAG (100 mJ, 10 Hz) etching + Transbond XT Primer; group 3: Er:YAG (200 mJ, 10 Hz) etching + Transbond XT Primer; group 4: Transbond Plus self-etching primer (SEP); group 5: Er:YAG (100 mJ, 10 Hz) etching + Transbond Plus SEP; group 6: Er:YAG (200 mJ, 10 Hz) etching + Transbond Plus SEP; group 7: Clearfil Protect Bond; group 8: Er:YAG (100 mJ, 10 Hz) etching + Clearfil Protect Bond; group 9: Er:YAG (200 mJ, 10 Hz) etching + Clearfil Protect Bond. Brackets were bonded with Transbond XT Adhesive Paste in all groups. Teeth to be evaluated for demineralization and SBS were exposed to pH and thermal cyclings, respectively. Then, demineralization samples were scanned with micro-CT to determine lesion depth values. For SBS test, a universal testing machine was used and adhesive remnant was index scored after debonding. Data were analyzed statistically. No significant differences were found among the lesion depth values of the various groups, except for G7 and G8, in which the lowest values were recorded. The lowest SBS values were in G7, whereas the highest were in G9. The differences between the other groups were not significant. Er:YAG laser did not have a positive effect on prevention of enamel demineralization. When two step self-etch adhesive is preferred for bonding brackets, laser etching at 1 W (100 mJ, 10 Hz) is suggested to improve SBS of brackets.

  9. Er internethandel kommet for at blive? Eller er det bare krisen som kradser?

    Ivang, Reimer

    2012-01-01

    I de seneste dage har Jyllandsposten sat fokus på, at omsætningen i den danske detailhandel falder, der fyres, der spares, og det bliver endnu værre i de kommende måneder og år. I artiklen udråbes finanskrisen, som den store skurk, men er det nu den fulde sandhed?...

  10. Minimising Immunohistochemical False Negative ER Classification Using a Complementary 23 Gene Expression Signature of ER Status

    Li, Qiyuan; Eklund, Aron Charles; Birkbak, Nicolai Juul

    2010-01-01

    with clinical outcome. METHODOLOGY/PRINCIPAL FINDINGS: Firstly, ER status was discriminated by fitting the bimodal expression of ESR1 to a mixed Gaussian model. The discriminative power of ESR1 suggested bimodal expression as an efficient way to stratify breast cancer; therefore we identified a set of genes...

  11. Problems pilots face involving wind shear

    Melvin, W. W.

    1977-01-01

    Educating pilots and the aviation industry about wind shears presents a major problem associated with this meteorological phenomenon. The pilot's second most pressing problem is the need for a language to discuss wind shear encounters with other pilots so that the reaction of the aircraft to the wind shear encounter can be accurately described. Another problem is the flight director which gives a centered pitch command for a given angular displacement from the glide slope. It was suggested that they should instead be called flight path command and should not center unless the aircraft is actually correcting to the flight path.

  12. Shear viscosity of liquid mixtures: Mass dependence

    Kaushal, Rohan; Tankeshwar, K.

    2002-06-01

    Expressions for zeroth, second, and fourth sum rules of transverse stress autocorrelation function of two component fluid have been derived. These sum rules and Mori's memory function formalism have been used to study shear viscosity of Ar-Kr and isotopic mixtures. It has been found that theoretical result is in good agreement with the computer simulation result for the Ar-Kr mixture. The mass dependence of shear viscosity for different mole fraction shows that deviation from ideal linear model comes even from mass difference in two species of fluid mixture. At higher mass ratio shear viscosity of mixture is not explained by any of the emperical model. (author)

  13. Shear Melting of a Colloidal Glass

    Eisenmann, Christoph; Kim, Chanjoong; Mattsson, Johan; Weitz, David A.

    2010-01-01

    We use confocal microscopy to explore shear melting of colloidal glasses, which occurs at strains of ˜0.08, coinciding with a strongly non-Gaussian step size distribution. For larger strains, the particle mean square displacement increases linearly with strain and the step size distribution becomes Gaussian. The effective diffusion coefficient varies approximately linearly with shear rate, consistent with a modified Stokes-Einstein relationship in which thermal energy is replaced by shear energy and the length scale is set by the size of cooperatively moving regions consisting of ˜3 particles.

  14. Shear viscosity of liquid mixtures Mass dependence

    Kaushal, R

    2002-01-01

    Expressions for zeroth, second, and fourth sum rules of transverse stress autocorrelation function of two component fluid have been derived. These sum rules and Mori's memory function formalism have been used to study shear viscosity of Ar-Kr and isotopic mixtures. It has been found that theoretical result is in good agreement with the computer simulation result for the Ar-Kr mixture. The mass dependence of shear viscosity for different mole fraction shows that deviation from ideal linear model comes even from mass difference in two species of fluid mixture. At higher mass ratio shear viscosity of mixture is not explained by any of the emperical model.

  15. Den der ser, er den, der ses

    Bjerrum, Troels

    2010-01-01

    Udgangspunktet for afhandlingen er at undersøge, hvordan unge udsatte mennesker kan opnå personlig forandring ved hjælp af åndedrætstræning og meditation. Afhandlingen indleder med at beskrive de unges liv i en globalisering. Mange unge mennesker uden en social ansvarlig baggrund har ikke lært...... at foretage sig nødvendige samfundsmæssige valg. På grund af nederlag i hjem, skole, uddannelse og erhverv søger unge fællesskaber i ligestillede miljøer svarende til egen negative forventningspraksis. Den unge praktiserer en vanedannende negativ livsførelse, som eskalerer til yderligere socialt forfald. Unge......, der har levet i kriminalitet, misbrug og medmisbrug i lang tid, vil ikke være i stand til at realisere sig positivt pga. en personlig indgroet diskvalificerende forestilling. Afhandlingen forklarer, hvorledes negative oplevelser forbliver spændinger i menneskers krop. Teorier af Maurice Merleau...

  16. Vejen til helvede er brolagt med frelste intentioner

    Vestenskov, David

    2013-01-01

    Det åbenlyse spørgsmål omkring, hvorfor vi er i Afghanistan (eller hvorfor vi bliver?) er bestemt et relevant spørgsmål, men at klæbe et prædikat på om krigens manglende moralske troværdighed kræver mere end blot sure opstød. Er vi netop ikke blevet i Afghanistan grundet moralske principper?...

  17. Employer branding er også intern kommunikation

    Hansen, Heidi

    2016-01-01

    I videnssamfundet og serviceøkonomien er medarbejderne virksomhedens vigtigste ressource, men milleniumgenerationen er ikke trofaste overfor deres arbejdsplads – de har typisk 15-20 jobs i løbet af deres livstid. Et stærkt employer brand bidrager til at fastholde medarbejdere – og dermed...... kompetencer – i virksomheden, og medarbejderne er dermed en central målgruppe for employer branding....

  18. The ER in 3-D: a multifunctional dynamic membrane network

    Friedman, Jonathan R.; Voeltz, Gia K.

    2011-01-01

    The endoplasmic reticulum (ER) is a large, singular, membrane-bound organelle that has an elaborate 3-D structure with a diversity of structural domains. It contains regions that are flat and cisternal, ones that are highly curved and tubular, and others adapted to form contact with nearly every other organelle and with the plasma membrane. ER 3-D structure is determined by both integral ER membrane proteins and by interactions with the cytoskeleton. Here, we describe some of the factors that...

  19. Evaluating the Potential Bioactivity of a Novel Compound ER1626

    Wang, Lijun; Zeng, Yanyan; Wang, Tianling; Liu, Hongyi; Xiao, Hong; Xiang, Hua

    2014-01-01

    Background ER1626, a novel compound, is a derivate of indeno-isoquinoline ketone. This study was designed to evaluate the biological activity and potential anti-tumor mechanism of ER1626. Method MTT assay, scratch assay and flow cytometry were used to determine cell proliferation, cell migration and cell cycle distribution as well as cell apoptosis on human breast cancer MCF-7 cells and endometrial cancer Ishikawa cells. We also explored the antiangiogenic effect of ER1626 on HUVEC cells and ...

  20. Hvorfor er danske fødevarer dyre?

    Hansen, Henning Otte

    2015-01-01

    De danske fødevarepriser er generelt høje set i forhold til resten af EU og også i forhold til lande uden for EU. Overordnet set er der en række forklaringer på internationale prisforskelle, og der er også flere mulige årsager til de høje danske fødevarepriser. Forskelle i moms, kvalitet...

  1. Forbruget af træer og buske i Danmark

    Jensen, Jan Svejgaard; Laursen, Allan Bach; Kjær, Erik Dahl

    Træer og buske er vigtige elementer i byen og landskabet, og i Danmark bruges der mellem 60 og 80 millioner vedplanter hvert år. Forbruget har været konstant stigende og der er sket store forskydninger i forbrugsmønstret i retning af større fokus på mangfoldighed og autencitet. Undersøgelsen...... klarlægger forbrugsmønstret for træer og buske og undersøger, hvad brugerne lægger vægt på i deres valg af planter....

  2. Preparation of Erbium-169 (169Er) Using Natural Erbium Target

    Azmairit Aziz; Nana Suherman

    2009-01-01

    The therapeutic radiopharmaceuticals which is labelled by β-particle emission are now increasingly used in nuclear medicine. Erbium-169 ('1 69 Er) is one of radioisotopes that can be used for radiation synovectomy (radio synovectomy) in the treatment of inflammatory joint diseases (arthritis) due to its β- particle emission (T 1/2 =9.4 days, E β maximum =0.34 MeV). The preliminary study on preparation of 169 Er by using natural erbium oxide (Er 2 O 3 ) target irradiated at TRIGA 2000 Bandung reactor has been carried out. The irradiated target was dissolved in hydrochloric acid solution and gentle warming. The optimum condition of 169 Er preparation was obtained by dissolution of 169 Er 2 O 3 by using 1N HCl solution. The radiochemical purity of 169 ErCl 3 was determined by paper chromatography, thin layer chromatography and paper electrophoresis techniques. The solution of 169 ErCl 3 formed was obtained with the pH of 1.5 – 2, clear, with the specific activity of 0.48 – 0.71 MBq/mg Er. The solution has the radiochemical purity of 98.32 ± 1.28% and the radionuclide purity of 99.98%. Study on the stability of 169 ErCl 3 solution showed that the solution was still stable for 4 days at room temperature with the radiochemical purity more than 95%. (author)

  3. Pæren er faldet langt fra stammen

    Haarder, Jon Helt

    2013-01-01

    Roman: Hassan Preislers vellykkede debutroman udleverer ikke bare multikulti-industrien. Den er også en rablende diagnosticering af det moderne menneskes livsvilkår HASSAN PREISLER BRUN MANDS BYRDE 224 sider, 249,95 Lindhardt og Ringhof Er udkommet 4......Roman: Hassan Preislers vellykkede debutroman udleverer ikke bare multikulti-industrien. Den er også en rablende diagnosticering af det moderne menneskes livsvilkår HASSAN PREISLER BRUN MANDS BYRDE 224 sider, 249,95 Lindhardt og Ringhof Er udkommet 4...

  4. Er Web 2.0 klar til mainstream?

    Ivang, Reimer

    2009-01-01

    BLOG: Spørgsmålene der relateres til Web 2.0 er mange. Men en af de mest signifikante er om netop din virksomhed skal anvende Web 2.0 teknologier? Hvad kan I få ud af det?......BLOG: Spørgsmålene der relateres til Web 2.0 er mange. Men en af de mest signifikante er om netop din virksomhed skal anvende Web 2.0 teknologier? Hvad kan I få ud af det?...

  5. Evaluating the potential bioactivity of a novel compound ER1626.

    Wang, Lijun; Zeng, Yanyan; Wang, Tianling; Liu, Hongyi; Xiao, Hong; Xiang, Hua

    2014-01-01

    ER1626, a novel compound, is a derivate of indeno-isoquinoline ketone. This study was designed to evaluate the biological activity and potential anti-tumor mechanism of ER1626. MTT assay, scratch assay and flow cytometry were used to determine cell proliferation, cell migration and cell cycle distribution as well as cell apoptosis on human breast cancer MCF-7 cells and endometrial cancer Ishikawa cells. We also explored the antiangiogenic effect of ER1626 on HUVEC cells and chicken embryos. The expression of estrogen receptor protein was investigated with western-blot analysis. ER1626 down-regulated the expression of estrogen receptor α protein and up-regulated β protein in MCF-7 and Ishikawa cells. The value of IC50 of ER1626 on MCF-7 and Ishikawa cells were respectively 8.52 and 3.08 µmol/L. Meanwhile, ER1626 decreased VEGF secretion of MCF-7 and Ishikawa cells, disturbed the formation of VEGF-stimulated tubular structure in HUVEC cells, and inhibited the angiogenesis on the chicken chorioallantoic membrane. Scratch assay revealed that ER1626 suppressed the migration of MCF-7, Ishikawa and HUVEC cells. In addition to induction tumor cell apoptosis, ER1626 arrested cell cycle in G1/G0 phase in MCF-7 cells and G2/M phase in Ishikawa cells. In conclusion, our results demonstrated that ER1626 has favorable bioactivities to be a potential candidate against breast cancer and angiogenesis.

  6. Evaluating the potential bioactivity of a novel compound ER1626.

    Lijun Wang

    Full Text Available ER1626, a novel compound, is a derivate of indeno-isoquinoline ketone. This study was designed to evaluate the biological activity and potential anti-tumor mechanism of ER1626.MTT assay, scratch assay and flow cytometry were used to determine cell proliferation, cell migration and cell cycle distribution as well as cell apoptosis on human breast cancer MCF-7 cells and endometrial cancer Ishikawa cells. We also explored the antiangiogenic effect of ER1626 on HUVEC cells and chicken embryos. The expression of estrogen receptor protein was investigated with western-blot analysis.ER1626 down-regulated the expression of estrogen receptor α protein and up-regulated β protein in MCF-7 and Ishikawa cells. The value of IC50 of ER1626 on MCF-7 and Ishikawa cells were respectively 8.52 and 3.08 µmol/L. Meanwhile, ER1626 decreased VEGF secretion of MCF-7 and Ishikawa cells, disturbed the formation of VEGF-stimulated tubular structure in HUVEC cells, and inhibited the angiogenesis on the chicken chorioallantoic membrane. Scratch assay revealed that ER1626 suppressed the migration of MCF-7, Ishikawa and HUVEC cells. In addition to induction tumor cell apoptosis, ER1626 arrested cell cycle in G1/G0 phase in MCF-7 cells and G2/M phase in Ishikawa cells.In conclusion, our results demonstrated that ER1626 has favorable bioactivities to be a potential candidate against breast cancer and angiogenesis.

  7. Shear strength of clay and silt embankments.

    2009-09-01

    Highway embankment is one of the most common large-scale geotechnical facilities constructed in Ohio. In the past, the design of these embankments was largely based on soil shear strength properties that had been estimated from previously published e...

  8. Localization in inelastic rate dependent shearing deformations

    Katsaounis, Theodoros

    2016-09-18

    Metals deformed at high strain rates can exhibit failure through formation of shear bands, a phenomenon often attributed to Hadamard instability and localization of the strain into an emerging coherent structure. We verify formation of shear bands for a nonlinear model exhibiting strain softening and strain rate sensitivity. The effects of strain softening and strain rate sensitivity are first assessed by linearized analysis, indicating that the combined effect leads to Turing instability. For the nonlinear model a class of self-similar solutions is constructed, that depicts a coherent localizing structure and the formation of a shear band. This solution is associated to a heteroclinic orbit of a dynamical system. The orbit is constructed numerically and yields explicit shear localizing solutions. © 2016 Elsevier Ltd

  9. Recent progress in shear punch testing

    Hamilton, M.L.; Toloczko, M.B.; Lucas, G.E.

    1994-09-01

    The shear punch test was developed in response to the needs of the materials development community for small-scale mechanical properties tests. Such tests will be of great importance when a fusion neutron simulation device is built, since such a device is expected to have a limited irradiation volume. The shear punch test blanks a circular disk from a fixed sheet metal specimen, specifically a TEM disk. Load-displacement data generated during the test can be related to uniaxial tensile properties such as yield and ultimate strength. Shear punch and tensile tests were performed at room temperature on a number of unirradiated aluminum, copper, vanadium, and stainless steel alloys and on several irradiated aluminum alloys. Recent results discussed here suggest that the relationship between shear punch strength and tensile strength varies with alloy class, although the relationship determined for the unirradiated condition remains valid for the irradiated aluminum alloys

  10. Enhancing Rotational Diffusion Using Oscillatory Shear

    Leahy, Brian D.; Cheng, Xiang; Ong, Desmond C.; Liddell-Watson, Chekesha; Cohen, Itai

    2013-01-01

    Taylor dispersion - shear-induced enhancement of translational diffusion - is an important phenomenon with applications ranging from pharmacology to geology. Through experiments and simulations, we show that rotational diffusion is also enhanced

  11. Remote Sensing Wind and Wind Shear System.

    Contents: Remote sensing of wind shear and the theory and development of acoustic doppler; Wind studies; A comparison of methods for the remote detection of winds in the airport environment; Acoustic doppler system development; System calibration; Airport operational tests.

  12. Shear-induced phase changes in mixtures

    Romig, K.D.; Hanley, H.J.M.

    1986-01-01

    A thermodynamic theory to account for the behavior of liquid mixtures exposed to a shear is developed. One consequence of the theory is that shear-induced phase changes are predicted. The theory is based on a thermodynamics that includes specifically the shear rate in the formalism and is applied to mixtures by a straightforward modification of the corresponding states, conformalsolution approach. The approach is general but is used here for a mixture of Lennard-Jones particles with a Lennard-Jones equation of state as a reference fluid. The results are discussed in the context of the Scott and Van Konynenberg phase classification. It is shown that the influence of a shear does affect substantially the type of the phase behavior. Results from the model mixture are equated loosely with those from real polymeric liquids

  13. Evaluating interfacial shear stresses in composite hollo

    Aiham Adawi

    2016-09-01

    Full Text Available Analytical evaluation of the interfacial shear stresses for composite hollowcore slabs with concrete topping is rare in the literature. Adawi et al. (2014 estimated the interfacial shear stiffness coefficient (ks that governs the behavior of the interface between hollowcore slabs and the concrete topping using push-off tests. This parameter is utilized in this paper to provide closed form solutions for the differential equations governing the behavior of simply supported composite hollowcore slabs. An analytical solution based on the deformation compatibility of the composite section and elastic beam theory, is developed to evaluate the shear stresses along the interface. Linear finite element modeling of the full-scale tests presented in Adawi et al. (2015 is also conducted to validate the developed analytical solution. The proposed analytical solution was found to be adequate in estimating the magnitude of horizontal shear stress in the studied composite hollowcore slabs.

  14. Localization in inelastic rate dependent shearing deformations

    Katsaounis, Theodoros; Lee, Min-Gi; Tzavaras, Athanasios

    2016-01-01

    Metals deformed at high strain rates can exhibit failure through formation of shear bands, a phenomenon often attributed to Hadamard instability and localization of the strain into an emerging coherent structure. We verify formation of shear bands for a nonlinear model exhibiting strain softening and strain rate sensitivity. The effects of strain softening and strain rate sensitivity are first assessed by linearized analysis, indicating that the combined effect leads to Turing instability. For the nonlinear model a class of self-similar solutions is constructed, that depicts a coherent localizing structure and the formation of a shear band. This solution is associated to a heteroclinic orbit of a dynamical system. The orbit is constructed numerically and yields explicit shear localizing solutions. © 2016 Elsevier Ltd

  15. Acoustic waves in unbounded shear flows

    Chagelishvili, G.D.; Khujadze, G.R.; Lominadze, J.G.; Rogava, A.D.

    1996-05-01

    The linear evolution of acoustic waves in fluid flow with constant density and uniform shear of velocity is investigated. The process of the mean flow energy extraction by the three-dimensional acoustic waves which is due to the non-normality of linear dynamics in shear flows is analyzed. The thorough examination of the dynamics of different physical quantities, specifying the wave evolution, is outlined. The revealing of the behaviour becomes possible owing to the nonmodal approach that has been extensively used in the study of the perturbations evolution in shear flows since the beginning of the nineties. In addition, a detailed analyses of the physics of shear energy gain by vortex and acoustic perturbations is presented. (author). 28 refs, 7 figs

  16. Stress analysis of shear/compression test

    Nishijima, S.; Okada, T.; Ueno, S.

    1997-01-01

    Stress analysis has been made on the glass fiber reinforced plastics (GFRP) subjected to the combined shear and compression stresses by means of finite element method. The two types of experimental set up were analyzed, that is parallel and series method where the specimen were compressed by tilted jigs which enable to apply the combined stresses, to the specimen. Modified Tsai-Hill criterion was employed to judge the failure under the combined stresses that is the shear strength under the compressive stress. The different failure envelopes were obtained between the two set ups. In the parallel system the shear strength once increased with compressive stress then decreased. On the contrary in the series system the shear strength decreased monotonicly with compressive stress. The difference is caused by the different stress distribution due to the different constraint conditions. The basic parameters which control the failure under the combined stresses will be discussed

  17. Modeling and implementation of wind shear data

    Frost, Walter

    1987-01-01

    The problems of implementing the JAWS wind shear data are discussed. The data sets are described from the view of utilizing them in an aircraft performance computer program. Then, some of the problems of nonstandard procedures are described in terms of programming the equations of aircraft motion when the effects of temporal and spatially variable winds are included. Finally, some of the computed effects of the various wind shear terms are shown.

  18. Hydrodynamical fluctuations in smooth shear flows

    Chagelishvili, G.D.; Khujadze, G.R.; Lominadze, J.G.

    1999-11-01

    Background of hydrodynamical fluctuations in a intrinsically/stochastically forced, laminar, uniform shear flow is studied. The employment of so-called nonmodal mathematical analysis makes it possible to represent the background of fluctuations in a new light and to get more insight into the physics of its formation. The basic physical processes responsible for the formation of vortex and acoustic wave fluctuation backgrounds are analyzed. Interplay of the processes at low and moderate shear rates is described. Three-dimensional vortex fluctuations around a given macroscopic state are numerically calculated. The correlation functions of the fluctuations of physical quantities are analyzed. It is shown that there exists subspace D k in the wave-number space (k-space) that is limited externally by spherical surface with radius k ν ≡ A/ν (where A is the velocity shear parameter, ν - the kinematic viscosity) in the nonequilibrium open system under study. The spatial Fourier harmonics of vortex as well as acoustic wave fluctuations are strongly subjected by flow shear (by the open character of the system) at wave-numbers satisfying the condition k ν . Specifically it is shown that in D k : The fluctuations are non-Markovian; the spatial spectral density of energy of the vortex fluctuations by far exceeds the white-noise; the term of a new type associated to the hydrodynamical fluctuation of velocity appears in the correlation function of pressure; the fluctuation background of the acoustic waves is completely different at low and moderate shear rates (at low shear rates it is reduced in D k in comparison to the uniform (non-shear) flow; at moderate shear rates it it comparable to the background of the vortex fluctuations). The fluctuation background of both the vortex and the acoustic wave modes is anisotropic. The possible significance of the fluctuation background of vortices for the subcritical transition to turbulence and Brownian motion of small macroscopic

  19. Line Crack Subject to Antiplane Shear.

    1978-07-01

    shear is obtained for the initiation of fracture. If the concept of the surface tension is usedone is able to calculate the cohesive stress for brittle ...Expression of the Griffith -racture criterion for brittle fracture. We have arrived at this result via the maximum shear-stress hypothesis, rather than...Crescent Beach Road, Glen Cove Prof. G.S. Heller Long Island, New York 11542 Division of Engineering Brown University Prof. Daniel

  20. Experimental study of shear rate dependence in perpetually sheared granular matter

    Liu, Sophie Yang; Guillard, François; Marks, Benjy; Rognon, Pierre; Einav, Itai

    2017-06-01

    We study the shear behaviour of various granular materials by conducting novel perpetual simple shear experiments over four orders of magnitude of relatively low shear rates. The newly developed experimental apparatus employed is called "3D Stadium Shear Device" which is an extended version of the 2D Stadium Shear Device [1]. This device is able to provide a non-radial dependent perpetual shear flow and a nearly linear velocity profile between two oppositely moving shear walls. Using this device, we are able to test a large variety of granular materials. Here, we demonstrate the applicability of the device on glass beads (diameter 1 mm, 3 mm, and 14 mm) and rice. We particularly focus on studying these materials at very low inertial number I ranging from 10-6 to 10-2. We find that, within this range of I, the friction coefficient μ of glass beads has no shear rate dependence. A particularly appealing observation comes from testing rice, where the attainment of critical state develops under much longer duration than in other materials. Initially during shear we find a value of μ similar to that found for glass beads, but with time this value decreases gradually towards the asymptotic critical state value. The reason, we believe, lies in the fact that rice grains are strongly elongated; hence the time to achieve the stable μ is primarily controlled by the time for particles to align themselves with respect to the shear walls. Furthermore, the initial packing conditions of samples also plays a role in the evolution of μ when the shear strain is small, but that impact will eventually be erased after sufficient shear strain.

  1. Shear Strains, Strain Rates and Temperature Changes in Adiabatic Shear Bands

    1980-05-01

    X14A. It has been found that when bainitic and martensitic steels are sheared adiabatically, a layer of material within ths shear zone is altezed and...Sooiety for Metals, Metals Park, Ohio, 1978, pp. 148-0. 21 TABLE II SOLID-STATE TRANSFORMATIONS IN BAINITIC STEEL TRANSFORMATION TRANSFORMATION...shear, thermoplastic, plasticity, plastic deformation, armor, steel IL AnSRACT ( -=nba asoa.tm a naeoesM iN faity by bleak n bet/2972 Experiments

  2. Shear flow effect on ion temperature gradient vortices in plasmas with sheared magnetic field

    Chakrabarti, N.; Juul Rasmussen, J.

    1999-01-01

    The effect of velocity shear on ion temperature gradient (ITG) driven vortices in a nonuniform plasma in a curved, sheared magnetic field is investigated. In absence of parallel ion dynamics, vortex solutions for the ITG mode are studied analytically. It is shown that under certain conditions...... and ultimately lead to a dominating monopolar form. The effects of magnetic shear indicate it may destroy these structures. (C) 1999 American Institute of Physics....

  3. Experimental study of shear rate dependence in perpetually sheared granular matter

    Liu Sophie Yang

    2017-01-01

    Full Text Available We study the shear behaviour of various granular materials by conducting novel perpetual simple shear experiments over four orders of magnitude of relatively low shear rates. The newly developed experimental apparatus employed is called “3D Stadium Shear Device” which is an extended version of the 2D Stadium Shear Device [1]. This device is able to provide a non-radial dependent perpetual shear flow and a nearly linear velocity profile between two oppositely moving shear walls. Using this device, we are able to test a large variety of granular materials. Here, we demonstrate the applicability of the device on glass beads (diameter 1 mm, 3 mm, and 14 mm and rice. We particularly focus on studying these materials at very low inertial number I ranging from 10−6 to 10−2. We find that, within this range of I, the friction coefficient μ of glass beads has no shear rate dependence. A particularly appealing observation comes from testing rice, where the attainment of critical state develops under much longer duration than in other materials. Initially during shear we find a value of μ similar to that found for glass beads, but with time this value decreases gradually towards the asymptotic critical state value. The reason, we believe, lies in the fact that rice grains are strongly elongated; hence the time to achieve the stable μ is primarily controlled by the time for particles to align themselves with respect to the shear walls. Furthermore, the initial packing conditions of samples also plays a role in the evolution of μ when the shear strain is small, but that impact will eventually be erased after sufficient shear strain.

  4. Resolution of axial shear strain elastography

    Thitaikumar, Arun; Righetti, Raffaella; Krouskop, Thomas A; Ophir, Jonathan

    2006-01-01

    The technique of mapping the local axial component of the shear strain due to quasi-static axial compression is defined as axial shear strain elastography. In this paper, the spatial resolution of axial shear strain elastography is investigated through simulations, using an elastically stiff cylindrical lesion embedded in a homogeneously softer background. Resolution was defined as the smallest size of the inclusion for which the strain value at the inclusion/background interface was greater than the average of the axial shear strain values at the interface and inside the inclusion. The resolution was measured from the axial shear strain profile oriented at 45 0 to the axis of beam propagation, due to the absence of axial shear strain along the normal directions. The effects of the ultrasound system parameters such as bandwidth, beamwidth and transducer element pitch along with signal processing parameters such as correlation window length (W) and axial shift (ΔW) on the estimated resolution were investigated. The results show that the resolution (at 45 0 orientation) is determined by the bandwidth and the beamwidth. However, the upper bound on the resolution is limited by the larger of the beamwidth and the window length, which is scaled inversely to the bandwidth. The results also show that the resolution is proportional to the pitch and not significantly affected by the axial window shift

  5. Accurate shear measurement with faint sources

    Zhang, Jun; Foucaud, Sebastien; Luo, Wentao

    2015-01-01

    For cosmic shear to become an accurate cosmological probe, systematic errors in the shear measurement method must be unambiguously identified and corrected for. Previous work of this series has demonstrated that cosmic shears can be measured accurately in Fourier space in the presence of background noise and finite pixel size, without assumptions on the morphologies of galaxy and PSF. The remaining major source of error is source Poisson noise, due to the finiteness of source photon number. This problem is particularly important for faint galaxies in space-based weak lensing measurements, and for ground-based images of short exposure times. In this work, we propose a simple and rigorous way of removing the shear bias from the source Poisson noise. Our noise treatment can be generalized for images made of multiple exposures through MultiDrizzle. This is demonstrated with the SDSS and COSMOS/ACS data. With a large ensemble of mock galaxy images of unrestricted morphologies, we show that our shear measurement method can achieve sub-percent level accuracy even for images of signal-to-noise ratio less than 5 in general, making it the most promising technique for cosmic shear measurement in the ongoing and upcoming large scale galaxy surveys

  6. Behavior of Tilted Angle Shear Connectors

    Khorramian, Koosha; Maleki, Shervin; Shariati, Mahdi; Ramli Sulong, N. H.

    2015-01-01

    According to recent researches, angle shear connectors are appropriate to transfer longitudinal shear forces across the steel-concrete interface. Angle steel profile has been used in different positions as L-shaped or C-shaped shear connectors. The application of angle shear connectors in tilted positions is of interest in this study. This study investigates the behaviour of tilted-shaped angle shear connectors under monotonic loading using experimental push out tests. Eight push-out specimens are tested to investigate the effects of different angle parameters on the ultimate load capacity of connectors. Two different tilted angles of 112.5 and 135 degrees between the angle leg and steel beam are considered. In addition, angle sizes and lengths are varied. Two different failure modes were observed consisting of concrete crushing-splitting and connector fracture. By increasing the size of connector, the maximum load increased for most cases. In general, the 135 degrees tilted angle shear connectors have a higher strength and stiffness than the 112.5 degrees type. PMID:26642193

  7. Behavior of Tilted Angle Shear Connectors.

    Koosha Khorramian

    Full Text Available According to recent researches, angle shear connectors are appropriate to transfer longitudinal shear forces across the steel-concrete interface. Angle steel profile has been used in different positions as L-shaped or C-shaped shear connectors. The application of angle shear connectors in tilted positions is of interest in this study. This study investigates the behaviour of tilted-shaped angle shear connectors under monotonic loading using experimental push out tests. Eight push-out specimens are tested to investigate the effects of different angle parameters on the ultimate load capacity of connectors. Two different tilted angles of 112.5 and 135 degrees between the angle leg and steel beam are considered. In addition, angle sizes and lengths are varied. Two different failure modes were observed consisting of concrete crushing-splitting and connector fracture. By increasing the size of connector, the maximum load increased for most cases. In general, the 135 degrees tilted angle shear connectors have a higher strength and stiffness than the 112.5 degrees type.

  8. Cosmology with cosmic shear observations: a review.

    Kilbinger, Martin

    2015-07-01

    Cosmic shear is the distortion of images of distant galaxies due to weak gravitational lensing by the large-scale structure in the Universe. Such images are coherently deformed by the tidal field of matter inhomogeneities along the line of sight. By measuring galaxy shape correlations, we can study the properties and evolution of structure on large scales as well as the geometry of the Universe. Thus, cosmic shear has become a powerful probe into the nature of dark matter and the origin of the current accelerated expansion of the Universe. Over the last years, cosmic shear has evolved into a reliable and robust cosmological probe, providing measurements of the expansion history of the Universe and the growth of its structure. We review here the principles of weak gravitational lensing and show how cosmic shear is interpreted in a cosmological context. Then we give an overview of weak-lensing measurements, and present the main observational cosmic-shear results since it was discovered 15 years ago, as well as the implications for cosmology. We then conclude with an outlook on the various future surveys and missions, for which cosmic shear is one of the main science drivers, and discuss promising new weak cosmological lensing techniques for future observations.

  9. Edge Sheared Flows and Blob Dynamics

    Myra, J.; D' Ippolito, D.; Russell, D., E-mail: jrmyra@lodestar.com [Lodestar Research Corporation, Boulder (United States); Davis, W. M.; Zweben, S. [Princeton Plasma Physics Laboratory, Princeton (United States); Terry, J.; LaBombard, B. [Massachusetts Institute of Technology, Cambridge (United States)

    2012-09-15

    Full text: A study of sheared flows in the edge and scrape-off layer (SOL) and their interaction with blob-filaments is presented. Edge sheared flows are believed to be important for the L-H, and H-L transitions. Blob generation and dynamics impacts both the (near-separatrix) scrape-off-layer (SOL) width critical for power handling in the divertor, and the interaction of plasma in the far SOL with plasma-facing components. These topics are critical for ITER and future devices. A fluid-based 2D curvature-interchange model embedded in the SOLT code is employed to study these issues. Sheared binormal flows both regulate the power flux crossing the separatrix and control the character of emitted turbulence structures such as blob-filaments. At a critical power level (depending on parameters) the laminar flows containing intermittent, but bound, structures give way to full-blown blob emissions signifying a transition from quasi-diffusive to convective transport. In order to diagnose sheared flows in experiments and assess their interaction with blobs, a blob-tracking algorithm has been developed and applied to both NSTX and Alcator C-Mod data. Blob motion and ellipticity can be affected by sheared flows, and are diagnosed and compared with seeded blob simulations. A picture of the interaction of blobs and sheared flows is emerging from advances in the theory and simulation of edge turbulence, combined with ever-improving capabilities for edge diagnostics and their analysis. (author)

  10. Vesicle dynamics in shear and capillary flows

    Noguchi, Hiroshi; Gompper, Gerhard

    2005-01-01

    The deformation of vesicles in flow is studied by a mesoscopic simulation technique, which combines multi-particle collision dynamics for the solvent with a dynamically triangulated surface model for the membrane. Shape transitions are investigated both in simple shear flows and in cylindrical capillary flows. We focus on reduced volumes, where the discocyte shape of fluid vesicles is stable, and the prolate shape is metastable. In simple shear flow at low membrane viscosity, the shear induces a transformation from discocyte to prolate with increasing shear rate, while at high membrane viscosity, the shear induces a transformation from prolate to discocyte, or tumbling motion accompanied by oscillations between these two morphologies. In capillary flow, at small flow velocities the symmetry axis of the discocyte is found not to be oriented perpendicular to the cylinder axis. With increasing flow velocity, a transition to a prolate shape occurs for fluid vesicles, while vesicles with shear-elastic membranes (like red blood cells) transform into a coaxial parachute-like shape

  11. Shear induced structures in crystallizing cocoa butter

    Mazzanti, Gianfranco; Guthrie, Sarah E.; Sirota, Eric B.; Marangoni, Alejandro G.; Idziak, Stefan H. J.

    2004-03-01

    Cocoa butter is the main structural component of chocolate and many cosmetics. It crystallizes in several polymorphs, called phases I to VI. We used Synchrotron X-ray diffraction to study the effect of shear on its crystallization. A previously unreported phase (phase X) was found and a crystallization path through phase IV under shear was observed. Samples were crystallized under shear from the melt in temperature controlled Couette cells, at final crystallization temperatures of 17.5^oC, 20^oC and 22.5^oC in Beamline X10A of NSLS. The formation of phase X was observed at low shear rates (90 s-1) and low crystallization temperature (17.5^oC), but was absent at high shear (720 s-1) and high temperature (20^oC). The d-spacing and melting point suggest that this new phase is a mixture rich on two of the three major components of cocoa butter. We also found that, contrary to previous reports, the transition from phase II to phase V can happen through the intermediate phase IV, at high shear rates and temperature.

  12. The brittle-viscous-plastic evolution of shear bands in the South Armorican Shear Zone

    Bukovská, Zita; Jeřábek, Petr; Morales, Luiz F. G.; Lexa, Ondrej; Milke, Ralf

    2014-05-01

    Shear bands are microscale shear zones that obliquely crosscut an existing anisotropy such as a foliation. The resulting S-C fabrics are characterized by angles lower than 45° and the C plane parallel to shear zone boundaries. The S-C fabrics typically occur in granitoids deformed at greenschist facies conditions in the vicinity of major shear zones. Despite their long recognition, mechanical reasons for localization of deformation into shear bands and their evolution is still poorly understood. In this work we focus on microscale characterization of the shear bands in the South Armorican Shear Zone, where the S-C fabrics were first recognized by Berthé et al. (1979). The initiation of shear bands in the right-lateral South Armorican Shear Zone is associated with the occurrence of microcracks crosscutting the recrystallized quartz aggregates that define the S fabric. In more advanced stages of shear band evolution, newly formed dominant K-feldspar, together with plagioclase, muscovite and chlorite occur in the microcracks, and the shear bands start to widen. K-feldspar replaces quartz by progressively bulging into the grain boundaries of recrystallized quartz grains, leading to disintegration of quartz aggregates and formation of fine-grained multiphase matrix mixture. The late stages of shear band development are marked by interconnection of fine-grained white mica into a band that crosscuts the original shear band matrix. In its extremity, the shear band widening may lead to the formation of ultramylonites. With the increasing proportion of shear band matrix from ~1% to ~12%, the angular relationship between S and C fabrics increases from ~30° to ~40°. The matrix phases within shear bands show differences in chemical composition related to distinct evolutionary stages of shear band formation. The chemical evolution is well documented in K-feldspar, where the albite component is highest in porphyroclasts within S fabric, lower in the newly formed grains within

  13. Structure of the /sup 168/Er nucleus and the /sup 166/Er(t,p)/sup 168/Er reaction in terms of the sdg interacting boson model

    Akiyama, Y.; Heyde, K.; Arima, A.; Yoshinaga, N.

    1986-05-29

    Extending the interacting boson model by incorporating besides s and d, also the g-boson, we can describe the population of positive parity states of /sup 168/Er in the /sup 166/Er(t,P)/sup 168/Er reaction rather well. In particular, the excitation of I,Ksub(i)sup(..pi..) = 4,3/sub 1//sup +/; 2,2/sub 2//sup +/; 0,0/sub 3//sup +/ and 0,0/sub 4//sup +/ states is much improved over the sd-IBM appraoch.

  14. Large magnetoresistance in Er7Rh3

    Sengupta, Kaushik; Sampathkumaran, E.V.

    2005-01-01

    The compound Er 2 Rh 3 has been known to order antiferromagnetically below (T N =14K), and to exhibit a change in the sign of temperature coefficient of electrical resistivity (ρ) in the paramagnetic state around 120 K. Here we report the influence of external magnetic field (H) on the ρ(T) behavior of this compound (1.8-300 K). While the ρ behavior in the paramagnetic state, qualitatively speaking, is found to be robust to the application of H, the magnitude of the magnetoresistance (MR) is significant for moderate applications of H, even at temperatures for above T N untypical of metallic systems. In addition, large values are observed in the magnetically ordered state. (author)

  15. Final Technical Report for Award # ER64999

    Metcalf, William W. [University of Illinois

    2014-10-08

    This report provides a summary of activities for Award # ER64999, a Genomes to Life Project funded by the Office of Science, Basic Energy Research. The project was entitled "Methanogenic archaea and the global carbon cycle: a systems biology approach to the study of Methanosarcina species". The long-term goal of this multi-investigator project was the creation of integrated, multiscale models that accurately and quantitatively predict the role of Methanosarcina species in the global carbon cycle under dynamic environmental conditions. To achieve these goals we pursed four specific aims: (1) genome sequencing of numerous members of the Order Methanosarcinales, (2) identification of genomic sources of phenotypic variation through in silico comparative genomics, (3) elucidation of the transcriptional networks of two Methanosarcina species, and (4) development of comprehensive metabolic network models for characterized strains to address the question of how metabolic models scale with genetic distance.

  16. ER@CEBAF: Modeling code developments

    Meot, F. [Brookhaven National Lab. (BNL), Upton, NY (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Roblin, Y. [Brookhaven National Lab. (BNL), Upton, NY (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2016-04-13

    A proposal for a multiple-pass, high-energy, energy-recovery experiment using CEBAF is under preparation in the frame of a JLab-BNL collaboration. In view of beam dynamics investigations regarding this project, in addition to the existing model in use in Elegant a version of CEBAF is developed in the stepwise ray-tracing code Zgoubi, Beyond the ER experiment, it is also planned to use the latter for the study of polarization transport in the presence of synchrotron radiation, down to Hall D line where a 12 GeV polarized beam can be delivered. This Note briefly reports on the preliminary steps, and preliminary outcomes, based on an Elegant to Zgoubi translation.

  17. Nonrotational states of 165Er nuclei

    Bonch-Osmolovskaya, N.A.; Morozov, V.A.; Nesterenko, V.O.

    1985-01-01

    165 Er nucleus excited states have been analysed on the basis of available experimental data and calculations within the framework of a quasiparticle-phonon model. β-vibrational components of states are included into the calculations, the Pauli principle was taken account of consecutively. Taking account of the Pauli principle permitting to perform a more correct description of vibrational components resulted in a marked change of characteristics of a number of states especially in the case of 9/2 + [624]. The whole set of levels with 1/2 - [521], 297.4 keV; 1/2 - [530], 589.9 keV; 1/2 - [510], 920.7 keV; 3/2, 1/2 - [541], 1039 keV, is described satisfactorily. The calculation performed gives as a whole a better agreement with experiment as compared with earlier calculations of other authors

  18. ER and PR expression and survival after endometrial cancer.

    Smith, Deborah; Stewart, Colin J R; Clarke, Edward M; Lose, Felicity; Davies, Claire; Armes, Jane; Obermair, Andreas; Brennan, Donal; Webb, Penelope M; Nagle, Christina M; Spurdle, Amanda B

    2018-02-01

    To measure association between endometrial carcinoma ER and PR status and endometrial cancer (EC) survival, accounting for inter-observer variation. The intensity and proportion of tumor cell expression of ER and PR in ECs were assessed independently and semi-quantitatively by two pathologists using digital images of duplicate tumor tissue microarrays (TMAs). Cases with inconsistent initial assessment were reviewed and final scoring agreed. The association between overall and EC-specific survival and hormone receptor expression (intensity, proportion and combined) was assessed using Cox regression analysis. The C-index was used to evaluate model discrimination with addition of ER and PR status. Tumor ER and PR analysis was possible in 659 TMAs from 255 patients, and in 459 TMAs from 243 patients, respectively. Initial ER and PR scoring was consistent in 82% and 80% of cases, respectively. In multivariate analyses decreased ER and PR expression was associated with increased tumor-related mortality. Associations reached statistical significance for ER proportion score (P=0.05), ER intensity score (P=0.003), and PR combined score (P=0.04). Decreased expression of combined ER/PR expression was associated with poorer EC-specific survival than decreased expression of either hormone receptor alone (P=0.005). However, hormone receptor status did not significantly improve mortality prediction in individual cases. ER and PR expression combined, using cut-points that capture variation in scoring and across cores, is significantly associated with EC-specific survival in analyses adjusting for known prognostic factors. However, at the individual level, ER and PR expression does not improve mortality prediction. Copyright © 2017 Elsevier Inc. All rights reserved.

  19. EC/β+ decay of 161Er

    Kalinnikov, V.G.; Ibraheem, Y.S.; Stegailov, V.I.

    2004-01-01

    Full text: The study of odd-proton nuclei in rare-earth region has been performed to get more information on the nuclear structure of these nuclei. In the framework of a program at the ISOL complex of YASNAPP-2 at JINR to study the decay of odd-nuclei, 161 Er has been investigated. The experiments have been focused on the 161 Ho level scheme populated in the EC/β + decay of 161 Er for which a few results have been previously reported [1,2]. Spectra of single γ-ray, γ-γ coincidence and internal conversion electrons were measured. There are appreciable disagreements between results of some γ-ray intensities obtained by us and in [2]. The greatest difference was for relative γ-ray intensity of the 11.28 keV, which has reported value I γ ∼ 10 (I γ 211 =1000) in [2], but this leads to an overpopulation of the 211 keV level by 14% of the decay [3]. The relative intensities of transitions with Eγ γ211 =1000). Inaccuracy of Iγ in [2] is probably due to a sudden change in the efficiency curve of their Ge(Li) detector in the low energy region while our HPGe detector feature a much smoother variation in the efficiency curve in this γ-ray energy region. Besides, the levels earlier introduced by us in [4], three new levels in 161 Ho were proposed from γ-γ coincidences at energies 693.2 keV, 859.6 keV, and 957.97 keV. Spins, parities and Nilsson quantum characteristics of some 161 Ho levels were established

  20. Evolution of allowable stresses in shear for lumber

    Robert L. Ethington; William L. Galligan; Henry M. Montrey; Alan D. Freas

    1979-01-01

    This paper surveys research leading to allowable shear stress parallel to grain for lumber. In early flexure tests of lumber, some pieces failed in shear. The estimated shear stress at time of failure was generally lower than shear strength measured on small, clear, straight-grained specimens. This and other engineering observations gave rise to adjustments that...

  1. Ikon. iPod er kongen over mp3. Hvad er hemmeligheden?

    Dickson, Thomas

    2005-01-01

    iPod er blevet ikonet for det 21. århundrede. Men iPod var hverken den første mp3-afspiller eller den første veldesignede af slagsen. Før iPod så dagens lys var Bang & Olufsen på banen med sin næsten lige så lækre BeoSound2.......iPod er blevet ikonet for det 21. århundrede. Men iPod var hverken den første mp3-afspiller eller den første veldesignede af slagsen. Før iPod så dagens lys var Bang & Olufsen på banen med sin næsten lige så lækre BeoSound2....

  2. “Når man er tvunget ud i det, er det egentlig meget godt”

    Christiansen, René Boyer; Lilius, Karin Marianne; Petersen, Jørgen Haagen

    2018-01-01

    , er en nødvendighed for kompetenceudvikling understøttet af metoden lektionsstudier samt relevante stilladseringsværktøjer der kan rammesætte udviklingen af undervisningskompeten-cer – i dette tilfælde et såkaldt P-CKema. Desuden peger projektets empiri på at projekter der søger at udvikle...

  3. Exponential Shear Flow of Linear, Entangled Polymeric Liquids

    Neergaard, Jesper; Park, Kyungho; Venerus, David C.

    2000-01-01

    A previously proposed reptation model is used to interpret exponential shear flow data taken on an entangled polystyrenesolution. Both shear and normal stress measurements are made during exponential shear using mechanical means. The model iscapable of explaining all trends seen in the data......, and suggests a novel analysis of the data. This analysis demonstrates thatexponential shearing flow is no more capable of stretching polymer chains than is inception of steady shear at comparableinstantaneous shear rates. In fact, all exponential shear flow stresses measured are bounded quantitatively...

  4. Er der forskel på grinder og grise?

    Heðinsdóttir, Katla; Gjerris, Mickey

    2015-01-01

    Når det gælder grindedrab, burde man måske spørge, om en tradition, som involverer smerte, angst og andre negative følelser for dyr, er værd at holde fast i, og om det ikke er muligt at fastholde en færøsk identitet uden grindefangst....

  5. Det man hører, er man selv

    Svømmekjær, Heidi Frank

    2012-01-01

    Katalog til udstillingen "Det man hører, er man selv" på Mediemuseet i Odense 7. september 2012 - 15. januar 2013.......Katalog til udstillingen "Det man hører, er man selv" på Mediemuseet i Odense 7. september 2012 - 15. januar 2013....

  6. Zebrafisken er et vigtigt forsøgsdyr

    Kjær-Sørensen, Kasper; Alstrup, Aage Kristian Olsen

    2017-01-01

    Det kan ved første øjekast undre, at en almindelig dansk akvariefisk er blevet forskernes favorit. Ikke desto mindre er det tilfældet for den lille zebrafisk (Danio rerio), som i disse år anvendes til at undersøge funktionen af gener, til at lave dyremodeller for menneskets sygdomme og til...

  7. Dietary toxins, endoplasmic reticulum (ER) stress and diabetes.

    Hettiarachchi, Kalindi D; Zimmet, Paul Z; Myers, Mark A

    2008-05-01

    The incidence of Type 1 diabetes has been increasing at a rate too rapid to be due to changes in genetic risk. Instead changes in environmental factors are the likely culprit. The endoplasmic reticulum (ER) plays an important role in the production of newly synthesized proteins and interference with these processes leads to ER stress. The insulin-producing beta cells are particularly prone to ER stress as a result of their heavy engagement in insulin production. Increasing evidence suggests ER stress is central to initiation and progression of Type 1 diabetes. An early environmental exposure, such as toxins and viral infections, can impart a significant physiological load on beta cells to initiate abnormal processing of proinsulin, ER stress and insulin secretory defects. Release of altered proinsulin from the beta cells early in life may trigger autoimmunity in those with genetic susceptibility leading to cytokine-induced nitric oxide production and so exacerbating ER stress in beta cells, ultimately leading to apoptosis of beta cells and diabetes. Here we suggest that ER stress is an inherent cause of beta cell dysfunction and environmental factors, in particular dietary toxins derived from Streptomyces in infected root vegetables, can impart additional stress that aggravates beta cell death and progression to diabetes. Furthermore, we propose that the increasing incidence of Type 1 diabetes may be accounted for by increased dietary exposure to ER-stress-inducing Streptomyces toxins.

  8. Hvilke planter er hjemmehørende i Danmark?

    Erik, Buchwald,; Wind, Peter; Bruun, Hans Henrik

    2013-01-01

    Der har i de senere år været debat om, hvorvidt konkrete plantearter - fx Ær (Acer pseudoplatanus) og Gyvel (Cytisus scoparius) - er hjemmehørende arter i Danmark eller indførte fremmede (Buchwald 2008, 20110: Friis 2010: Møller 2011; Bruun2011). En medvirkende årsag til diskussionerne er, at derr...

  9. Giv Kejseren hvad Kejserens er - på langt sigt

    Sestoft, Carsten

    2007-01-01

    Fra OECD over EU til det danske videnskabsministerium er der en mængde magtfulde instanser, som i det seneste årti har stillet en række nye krav til universiteterne. Kravene kan i korthed sammenfattes som en fordring om samfundsmæssig og økonomisk relevans. Artiklen argumenterer for, at det er le...

  10. Ny vaccine mod ledbetændelse er ikke effektiv

    Nielsen, Elisabeth Okholm; Lauritsen, Klara Tølbøll

    2013-01-01

    En ny mulighed for at vaccinere mod mykoplasma-ledbetændelse er undersøgt hos en slagtesvineproducent. Vaccinen kunne desværre ikke forebygge halthed eff ektivt.......En ny mulighed for at vaccinere mod mykoplasma-ledbetændelse er undersøgt hos en slagtesvineproducent. Vaccinen kunne desværre ikke forebygge halthed eff ektivt....

  11. Hvad er fantastisk ved HBO-serien Game of Thrones?

    Schubart, Rikke

    2013-01-01

    Blogindlæg på videnskab.dk, kaldt "Hvad er fantastisk ved HBO-serien Game of Thrones?" om HBO tv-serien Game of Thrones......Blogindlæg på videnskab.dk, kaldt "Hvad er fantastisk ved HBO-serien Game of Thrones?" om HBO tv-serien Game of Thrones...

  12. Din tandbørste og pejsen er online

    Damsgaard, Jan

    2016-01-01

    Det er snart definitivt slut med de store mysterier om flys forsvinden og massive eftersøgninger efter overlevende. Danske Naviair er i disse år med til at sende 66 satellitter i kredsløb om Jorden. Så kan alle kommercielle fly følges, uanset hvor på jordkloden de befinder sig....

  13. Danskhed er pizza, kebab og flæskesteg

    Mehlsen, Camilla

    2010-01-01

    Dannebrog. Kongehuset. Flæskesteg. Folkeskolen. Fodbold og øl. En lang række symboler og fortællinger kendetegner danskhed, men det er en myte, at danskerne er en homogen gruppe, fortæller professor Richard Jenkins....

  14. Study of shear thickening behavior in colloidal suspensions

    N Maleki Jirsaraee

    2015-01-01

    Full Text Available We studied the shear thickening behavior of the nano silica suspension (silica nanoparticles 12 nm in size suspended in ethylene glycol under steady shear. The critical shear rate for transition into shear thickening phase was determined at different concentrations and temperatures. The effect of temperature and concentration was studied on the shear thickening behavior. In silica suspension, it was observed that all the samples had a transition into shear thickening phase and also by increasing the temperature, critical shear rate increased and viscosity decreased. Our observations showed that movement in silica suspension was Brownian and temperature could cause a delay in transition into shear thickening phase. Yet, we observed that increasing the concentration would decrease critical shear rate and increase viscosity. Increasing temperature increased Brownian forces and increasing concentration increased hydrodynamic forces, confirming the contrast between these two forces for transition into shear thickening phase for the suspensions containing nano particles

  15. Bond strengths of brackets bonded to enamel surfaces conditioned with femtosecond and Er:YAG laser systems.

    Aglarci, Cahide; Demir, Necla; Aksakalli, Sertac; Dilber, Erhan; Sozer, Ozlem Akinci; Kilic, Hamdi Sukur

    2016-08-01

    The aim of this study was to compare femtosecond and Er:YAG laser systems with regard to enamel demineralization and bracket bond strength. Human-extracted premolars were randomized to three groups (n = 17) depending on the conditioning treatment used for the buccal surfaces: 37 % orthophosphoric acid, Er:YAG laser etching (MSP mode 120 mJ, 10 Hz, 1.2 W), and femtosecond laser etching (0.4 W, 800 nm, 90 fs/pulse, 1 kHz). Metal brackets were bonded with Transbond XT to the conditioned surfaces and light cured for 20 s. The samples were thermocycled (5000 cycles, 5-55 °C) and subjected to shear bond strength (SBS) testing using a universal testing machine. Failure types were analyzed under an optical stereomicroscope and SEM. The adhesive remnant index (ARI) was evaluated to assess residual adhesive on the enamel surface. The results revealed no significant differences in SBS between the Er:YAG laser (7.2 ± 3.3 MPa) and acid etching groups (7.3 ± 2.7 MPa; p enamel interface.

  16. The ER in 3D: a multifunctional dynamic membrane network.

    Friedman, Jonathan R; Voeltz, Gia K

    2011-12-01

    The endoplasmic reticulum (ER) is a large, singular, membrane-bound organelle that has an elaborate 3D structure with a diversity of structural domains. It contains regions that are flat and cisternal, ones that are highly curved and tubular, and others adapted to form contacts with nearly every other organelle and with the plasma membrane. The 3D structure of the ER is determined by both integral ER membrane proteins and by interactions with the cytoskeleton. In this review, we describe some of the factors that are known to regulate ER structure and discuss how this structural organization and the dynamic nature of the ER membrane network allow it to perform its many different functions. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Comparison of direct shear and simple shear responses of municipal solid waste in USA

    Fei, Xunchang

    2017-10-25

    Although large-size simple shear (SS) testing of municipal solid waste (MSW) may arguably provide a more realistic estimate of the shear strength (τ ) of MSW than the most commonly used direct shear (DS) testing, a systematic comparison between the shear responses of MSW obtained from the two testing methods is lacking. In this study, a large-size shear device was used to test identical MSW specimens sampled in USA in DS and SS. Eight DS tests and 11 SS tests were conducted at vertical effective stresses of 50–500 kPa. The stress–displacement response of MSW in SS testing was hyperbolic and a maximum shear stress was reached, whereas a maximum shear stress was not reached in most DS tests. The τ, effective friction angle (ϕ ′) and cohesion (c ′) of MSW were obtained from DS and SS tests by using a displacement failure criterion of 40 mm. τ in SS testing was found to be equal to or lower than τ in DS testing with ratios of τ between 73 and 101%. SS testing resulted in higher ϕ ′ but lower c ′ than DS testing. The shear strength parameters were lower than those obtained in previous studies from DS tests at 55 mm displacement.

  18. Piezoelectric energy harvesting through shear mode operation

    Malakooti, Mohammad H; Sodano, Henry A

    2015-01-01

    Piezoelectric materials are excellent candidates for use in energy harvesting applications due to their high electromechanical coupling properties that enable them to convert input mechanical energy into useful electric power. The electromechanical coupling coefficient of the piezoelectric material is one of the most significant parameters affecting energy conversion and is dependent on the piezoelectric mode of operation. In most piezoceramics, the d 15 piezoelectric shear coefficient is the highest coefficient compared to the commonly used axial and transverse modes that utilize the d 33 and the d 31 piezoelectric strain coefficients. However, complicated electroding methods and challenges in evaluating the performance of energy harvesting devices operating in the shear mode have slowed research in this area. The shear deformation of a piezoelectric layer can be induced in a vibrating sandwich beam with a piezoelectric core. Here, a model based on Timoshenko beam theory is developed to predict the electric power output from a cantilever piezoelectric sandwich beam under base excitations. It is shown that the energy harvester operating in the shear mode is able to generate ∼50% more power compared to the transverse mode for a numerical case study. Reduced models of both shear and transverse energy harvesters are obtained to determine the optimal load resistance in the system and perform an efficiency comparison between two models with fixed and adaptive resistances. (paper)

  19. Evaluation of shear mounted elastomeric damper

    Zorzi, E.; Walton, J.

    1982-01-01

    Viton-70 elastomeric shear mounted damper was built and tested on a T-55 power turbine spool in the rotor's high speed balancing rig. This application of a shear mounted elastomeric damper demonstrated for the first time, the feasibility of using elastomers as the primary rotor damping source in production turbine engine hardware. The shear damper design was selected because it was compatible with actual gas turbine engine radial space constraints, could accommodate both the radial and axial thrust loads present in gas turbine engines, and was capable of controlled axial preload. The shear damper was interchangeable with the production T-55 power turbine roller bearing support so that a direct comparison between the shear damper and the production support structure could be made. Test results show that the Viton-70 elastomer damper operated successfully and provided excellent control of both synchronous and nonsynchronous vibrations through all phases of testing up to the maximum rotor speed of 16,000 rpm. Excellent correlation between the predicted and experienced critical speeds, mode shapes and log decrements for the power turbine rotor and elastomer damper assembly was also achieved.

  20. Ballooning mode stabilization by moderate sheared rotation

    Hameiri, E.

    1996-01-01

    Sheared toroidal plasma rotation has been known for some time to have a stabilizing effect on the ballooning modes. A recent calculation showed that a large flow shear, with dΩ/dq of the order of the Alfven toroidal frequency, can stabilize the ballooning modes. This latest result is, in fact, not so optimistic. For observed flows with Mach number of order unity one gets dΩ/dq smaller by a factor O(√β) from the required level (if the flow shear length is of the same order as the magnetic shear length). Moreover, the calculation does not take into account a possibly large transient growth of the mode amplitude due to its Floquet structures We show here that, in fact, there is a general tendency of the ballooning mode to stabilize as soon as the flow shear dΩ/dq exceeds the (O√β smaller) open-quotes slowclose quotes magnetosonic wave frequency. Our analysis is perturbative, where the small parameter is related to the small coupling between the slow and Alfven waves-as is the case in a high aspect-ratio tokamak. (In the perturbation it is important to take the Hamiltonian nature of the governing equations into account.) Moreover, our results apply to the relevant transient growth of the mode amplitude

  1. Delayed shear enhancement in mesoscale atmospheric dispersion

    Moran, M.D. [Atmospheric Environment Service, Ontario (Canada); Pielke, R.A. [Colorado State Univ., Fort Collins, CO (United States)

    1994-12-31

    Mesoscale atmospheric dispersion (MAD) is more complicated than smaller-scale dispersion because the mean wind field can no longer be considered steady or horizontally homogeneous over mesoscale time and space scales. Wind shear also plays a much more important role on the mesoscale: horizontal dispersion can be enhanced and often dominated by vertical wind shear on these scales through the interaction of horizontal differential advection and vertical mixing. Just over 30 years ago, Pasquill suggested that this interaction need not be simultaneous and that the combination of differential horizontal advection with delayed or subsequent vertical mixing could maintain effective horizontal diffusion in spite of temporal or spatial reductions in boundary-layer turbulence intensity. This two-step mechanism has not received much attention since then, but a recent analysis of observations from and numerical simulations of two mesoscale tracer experiments suggests that delayed shear enhancement can play an important role in MAD. This paper presents an overview of this analysis, with particular emphasis on the influence of resolvable vertical shear on MAD in these two case studies and the contributions made by delayed shear enhancement.

  2. Examining shear processes during magma ascent

    Kendrick, J. E.; Wallace, P. A.; Coats, R.; Lamur, A.; Lavallée, Y.

    2017-12-01

    Lava dome eruptions are prone to rapid shifts from effusive to explosive behaviour which reflects the rheology of magma. Magma rheology is governed by composition, porosity and crystal content, which during ascent evolves to yield a rock-like, viscous suspension in the upper conduit. Geophysical monitoring, laboratory experiments and detailed field studies offer the opportunity to explore the complexities associated with the ascent and eruption of such magmas, which rest at a pivotal position with regard to the glass transition, allowing them to either flow or fracture. Crystal interaction during flow results in strain-partitioning and shear-thinning behaviour of the suspension. In a conduit, such characteristics favour the formation of localised shear zones as strain is concentrated along conduit margins, where magma can rupture and heal in repetitive cycles. Sheared magmas often record a history of deformation in the form of: grain size reduction; anisotropic permeable fluid pathways; mineral reactions; injection features; recrystallisation; and magnetic anomalies, providing a signature of the repetitive earthquakes often observed during lava dome eruptions. The repetitive fracture of magma at ( fixed) depth in the conduit and the fault-like products exhumed at spine surfaces indicate that the last hundreds of meters of ascent may be controlled by frictional slip. Experiments on a low-to-high velocity rotary shear apparatus indicate that shear stress on a slip plane is highly velocity dependent, and here we examine how this influences magma ascent and its characteristic geophysical signals.

  3. Shear modulation experiments with ECCD on TCV

    Cirant, S.; Alberti, S.; Gandini, F.; Behn, R.; Goodman, T.P.; Nikkola, P.

    2006-01-01

    Anomalous electron transport is determined by turbulence, which in turn is affected by magnetic shear. A novel application of electron cyclotron current drive (ECCD), aiming at localized shear modulation, has been applied on the TCV tokamak for experiments on shear-dependent electron transport. Pairs of EC beams, absorbed at the same radius, with one oriented for co- and the other for counter-injection, are modulated out of phase in order to force a local modulation of current-density at constant input power. Off-axis deposition (ρ dep = 0.24) is performed to avoid the central region, where the low heat flux would make transport analysis difficult. In addition some sawteeth control is achieved in this way. A significant impact on local shear is achieved with I ECCD ∼ 0.1I OH , even when the modulation period is much shorter than the current diffusion time across the whole plasma radius. The main result is that although source (heat and particle) terms are constant, both electron density and temperature are modulated during alternated ECCD. Once equilibrium effects are taken into account for appropriate mapping of Thomson scattering measurements onto flux coordinates, modulation of T e and electron pressure, peaked on-axis, is confirmed at all radii internal to EC deposition. The best confinement occurs for co-injection, in which case a local decrease (∼55%) in the magnetic shear causes a decrease in the electron thermal diffusivity of a similar amount (∼65%)

  4. Self-diffusion of Er and Hf inpure and HfO2-doped polycrystalline Er2O3

    Scheidecker, R.W.

    1979-01-01

    Using a tracer technique, self-diffusion of Er and Hf was measured over the approximate temperature interval of 1600 to 1970 0 C in pure and HfO 2 -doped polycryatalline Er 2 O 3 . Up to about 10 m/o HfO 2 dopant level, the Er self-diffusion coefficients followed a relationship based on cation vacancies. Above 10 m/o HfO 2 , deviation from this relationship occurred, apparently due to clustering of cation vacancies and oxygen interstitials around the dopant hafnia ion. The activation energy for the self-diffusion of Er in pure Er 2 O 3 was 82.2 Kcal/mole and increased with the HfO 2 dopant level present. Self-diffusion of Hf was measured in pure Er 2 O 3 having two impurity levels, and a separation of the grain boundary. The volume diffusion of Hf showed both extrinsic and intrinsic behavior with the transition temperature increasing with the impurity level present in Er 2 O 3 . The activation energy for Hf volume diffusion in the intrinsic region was high, i.e. 235 -+ 9.5 Kcal/mole. The grain boundary diffusion was apparently extrinsic over the entire temperature interval Very low Hf self diffusion rates were found in both pure and HfO 2 doped Er 2 O 3 compositions. Despite a clustering effect, the HfO 2 dopant increased the Hf volume diffusion coefficients

  5. The effect of Er:YAG laser irradiation on the bond stability of self-etch adhesives at different dentin depths.

    Karadas, Muhammet; Çağlar, İpek

    2017-07-01

    The aim of this study was to evaluate the effect of Er:YAG laser irradiation on the micro-shear bond strength of self-etch adhesives to the superficial dentin and the deep dentin before and after thermocycling. Superficial dentin and deep dentin surfaces were prepared by flattening of the occlusal surfaces of extracted human third molars. The deep or superficial dentin specimens were randomized into three groups according to the following surface treatments: group I (control group), group II (Er:YAG laser; 1.2 W), and group III (Er:YAG laser; 0.5 W). Clearfil SE Bond or Clearfil S 3 Bond was applied to each group's dentin surfaces. After construction of the composite blocks on the dentin surface, the micro-shear bond testing of each adhesive was performed at 24 h or after 15,000 thermal cycles. The data were analyzed using a univariate analysis of variance and Tukey's test (p  0.05). However, deep-dentin specimens irradiated with laser showed significantly higher bond strengths than did control specimens after thermocycling (p adhesives may be altered by the dentin depth. Regardless of the applied surface treatment, deep dentin showed significant bond degradation.

  6. Effect of Er3+ Concentration on Upconversion in Hexagonal-Phase NaYF4:Er3+ Nanocrystals

    Luo, X J; Yuminami, R; Sakurai, T; Akimoto, K

    2013-01-01

    A facile synthesis method was developed to produce hexagonal-phase of NaYF 4 nanocrystals (NCs) doped with Er 3+ in different concentration, which showed upconversion (UC) emission from infrared to visible spectral region. This proposed method is simple and less toxic compared with generally used method so far. It was found that up-conversion emission spectra of NaYF 4 :Er 3+ NCs, excited at 1550 nm, included four peaks at about 980 nm, 800 nm, 660 nm and 540 nm. The effect of Er 3+ concentration on UC in β-phase NaYF 4 :Er 3+ NCs were discussed based on the excitation power dependence. The optimum Er 3+ concentration for 2-step and 3-step UC was found to be around 10∼30%.

  7. Shear and extensional properties of kefiran.

    Piermaría, Judith; Bengoechea, Carlos; Abraham, Analía Graciela; Guerrero, Antonio

    2016-11-05

    Kefiran is a neutral polysaccharide constituted by glucose and galactose produced by Lactobacillus kefiranofaciens. It is included into kefir grains and has several health promoting properties. In the present work, shear and extensional properties of different kefiran aqueous dispersions (0.5, 1 and 2% wt.) were assessed and compared to other neutral gums commonly used in food, cosmetic and pharmaceutics industries (methylcellulose, locust bean gum and guar gum). Kefiran showed shear flow characteristics similar to that displayed by other representative neutral gums, although it always yielded lower viscosities at a given concentration. For each gum system it was possible to find a correlation between dynamic and steady shear properties by a master curve including both the apparent and complex viscosities. When studying extensional properties of selected gums at 2% wt. by means of a capillary break-up rheometer, kefiran solutions did not show important extensional properties, displaying a behaviour close the Newtonian. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. On transformation shear of precipitated zirconia particles

    Zhang, J.M.; Lam, K.Y.

    1993-01-01

    A model is proposed to investigate the transformation shear of the precipitated zirconia particles which undergo a stress-induced lattice transformation from tetragonal to monoclinic symmetry. Kinematically admissible twinning planes and the corresponding twinning elements are determined according to the continuum theory of dispacive phase transformation. It is postulated that only one twinning mode prevails in each transformed particle and that the minimization of elastic strain energy change dictates the morphology of the transformed variants. The transformation shear is determined by the twinning mode and the volume fraction of the corresponding variant. Numerical calculations show that each of the six kinematically admissible twinning modes may be kinematically favorable and therefore operate in constrained particle. The actual transformation shear in a transformed particle is shown to be dependent on the transformation stress, on the particle shape as well as on the lattice orientation relative to the principal axes of the ellipsoidal particle

  9. On shear rheology of gel propellants

    Rahimi, Shai; Peretz, Arie [RAFAEL, MANOR Propulsion and Explosive Systems Division, Haifa (Israel); Natan, Benveniste [Faculty of Aerospace Engineering, Technion - Israel Institute of Technology, Haifa (Israel)

    2007-04-15

    Selected fuel, oxidizer and simulant gels were prepared and rheologically characterized using a rotational rheometer. For fuel gelation both organic and inorganic gellants were utilized, whereas oxidizers and simulants were gelled with addition of silica and polysaccharides, respectively. The generalized Herschel-Bulkley constitutive model was found to most adequately represent the gels studied. Hydrazine-based fuels, gelled with polysaccharides, were characterized as shear-thinning pseudoplastic fluids with low shear yield stress, whereas inhibited red-fuming nitric acid (IRFNA) and hydrogen peroxide oxidizers, gelled with silica, were characterized as yield thixotropic fluids with significant shear yield stress. Creep tests were conducted on two rheological types of gels with different gellant content and the results were fitted by Burgers-Kelvin viscoelastic constitutive model. The effect of temperature on the rheological properties of gel propellant simulants was also investigated. A general rheological classification of gel propellants and simulants is proposed. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  10. Combined shearing interferometer and hartmann wavefront sensor

    Hutchin, R. A.

    1985-01-01

    A sensitive wavefront sensor combining attributes of both a Hartmann type of wavefront sensor and an AC shearing interferometer type of wavefront sensor. An incident wavefront, the slope of which is to be detected, is focussed to first and second focal points at which first and second diffraction gratings are positioned to shear and modulate the wavefront, which then diverges therefrom. The diffraction patterns of the first and second gratings are positioned substantially orthogonal to each other to shear the wavefront in two directions to produce two dimensional wavefront slope data for the AC shearing interferometer portion of the wavefront sensor. First and second dividing optical systems are positioned in the two diverging wavefronts to divide the sheared wavefront into an array of subapertures and also to focus the wavefront in each subaperture to a focal point. A quadrant detector is provided for each subaperture to detect the position of the focal point therein, which provides a first indication, in the manner of a Hartmann wavefront sensor, of the local wavefront slope in each subaperture. The total radiation in each subaperture, as modulated by the diffraction grating, is also detected by the quadrant detector which produces a modulated output signal representative thereof, the phase of which relative to modulation by the diffraction grating provides a second indication of the local wavefront slope in each subaperture, in the manner of an AC shearing interferometer wavefront sensor. The data from both types of sensors is then combined by long term averaging thereof to provide an extremely sensitive wavefront sensor

  11. Tv nyheder: Journalistiske Idealer er under Pres

    Thomsen, Line Hassall

    2013-01-01

    som tv-journalisterne ville ønske det. Tv-journalister har mange store idealer om god journalistik og public service. Men de vilkår journalisterne arbejder under gør idealerne nærmest umulige at opnå i dagligdagen. I dag er det ikke de journalistiske idealer men markedskræfterne der driver de...... Journalist” inside Public Service TV Newsrooms in the UK and Denmark’. Under ph.d.- studiet har jeg tilbragt halvandet år med deltager-observation på de fire største tv-redaktioner i England og Danmark. Jeg har observeret og deltaget i det daglige arbejde på redaktionerne hos TV Avisen og TV2 Nyhederne og i...... licensfinansieret tv-station. Men der tog jeg fejl. Jeg ledte efter forskelligheder, men fandt ligheder. Efterhånden som feltstudiet tog fat gik det op for mig at journalisterne på de fire forskellige tv-stationer arbejdede og tænkte ens. Derudover gik det op for mig at mange af journalisterne på de forskelligt...

  12. Enhancing Rotational Diffusion Using Oscillatory Shear

    Leahy, Brian D.

    2013-05-29

    Taylor dispersion - shear-induced enhancement of translational diffusion - is an important phenomenon with applications ranging from pharmacology to geology. Through experiments and simulations, we show that rotational diffusion is also enhanced for anisotropic particles in oscillatory shear. This enhancement arises from variations in the particle\\'s rotation (Jeffery orbit) and depends on the strain amplitude, rate, and particle aspect ratio in a manner that is distinct from the translational diffusion. This separate tunability of translational and rotational diffusion opens the door to new techniques for controlling positions and orientations of suspended anisotropic colloids. © 2013 American Physical Society.

  13. Seismic behavior of reinforced concrete shear walls

    Wang, F.; Gantenbein, F.

    1989-01-01

    Reinforced concrete shear walls have an important contribution to building stiffness. So, it is necessary to know their behavior under seismic loads. The ultimate behavior study of shear walls subjected to dynamic loadings includes: - a description of the nonlinear global model based on cyclic static tests, - nonlinear time history calculations for various forcing functions. The comparison of linear and nonlinear results shows important margins related to the ductility when the bandwidth of the forcing function is narrow and centred on the wall natural frequency

  14. Shear reinforced beams in autoclaved aerated concrete

    Cornelius, Thomas

    2010-01-01

    Shear behaviour in concrete materials is very well documented, for normal density concrete materials. In this paper results of various tests on low density concrete materials like aerated autoclaved concrete (in the following denoted aircrete) will be presented and analyzed for different combinat....... Codes for designing prefabricated reinforced components of aircrete structures have adopted these recently developed approaches.......Shear behaviour in concrete materials is very well documented, for normal density concrete materials. In this paper results of various tests on low density concrete materials like aerated autoclaved concrete (in the following denoted aircrete) will be presented and analyzed for different...

  15. Mechanisms of ER Stress-Mediated Mitochondrial Membrane Permeabilization.

    Gupta, Sanjeev

    2010-01-01

    During apoptosis, the process of mitochondrial outer membrane permeabilization (MOMP) represents a point-of-no-return as it commits the cell to death. Here we have assessed the role of caspases, Bcl-2 family members and the mitochondrial permeability transition pore on ER stress-induced MOMP and subsequent cell death. Induction of ER stress leads to upregulation of several genes such as Grp78, Edem1, Erp72, Atf4, Wars, Herp, p58ipk, and ERdj4 and leads to caspase activation, release of mitochondrial intermembrane proteins and dissipation of mitochondrial transmembrane potential (DeltaPsim). Mouse embryonic fibroblasts (MEFs) from caspase-9, -2 and, -3 knock-out mice were resistant to ER stress-induced apoptosis which correlated with decreased processing of pro-caspase-3 and -9. Furthermore, pretreatment of cells with caspase inhibitors (Boc-D.fmk and DEVD.fmk) attenuated ER stress-induced loss of DeltaPsim. However, only deficiency of caspase-9 and -2 could prevent ER stress-mediated loss of DeltaPsim. Bcl-2 overexpression or pretreatment of cells with the cell permeable BH4 domain (BH4-Tat) or the mitochondrial permeability transition pore inhibitors, bongkrekic acid or cyclosporine A, attenuated the ER stress-induced loss of DeltaPsim. These data suggest a role for caspase-9 and -2, Bcl-2 family members and the mitochondrial permeability transition pore in loss of mitochondrial membrane potential during ER stress-induced apoptosis.

  16. Shear zones between rock units with no relative movement

    Koyi, Hemin; Schmeling, Harro; Burchardt, Steffi

    2013-01-01

    Shear zones are normally viewed as relatively narrow deformation zones that accommodate relative displacement between two "blocks" that have moved past each other in opposite directions. This study reports localized zones of shear between adjacent blocks that have not moved past each other. Such ...... given credit for and may be responsible for some reverse kinematics reported in shear zones....... or wakes, elongated bodies (vertical plates or horizontal rod-like bodies) produce tabular shear zones or wakes. Unlike conventional shear zones across which shear indicators usually display consistent symmetries, shear indicators on either side of the shear zone or wake reported here show reverse...... kinematics. Thus profiles exhibit shear zones with opposed senses of movement across their center-lines or -planes.We have used field observations and results from analytical and numerical models to suggest that examples of wakes are the transit paths that develop where denser blocks sink within salt...

  17. Shear thinning and shear thickening of a confined suspension of vesicles

    Nait Ouhra, A.; Farutin, A.; Aouane, O.; Ez-Zahraouy, H.; Benyoussef, A.; Misbah, C.

    2018-01-01

    Widely regarded as an interesting model system for studying flow properties of blood, vesicles are closed membranes of phospholipids that mimic the cytoplasmic membranes of red blood cells. In this study we analyze the rheology of a suspension of vesicles in a confined geometry: the suspension, bound by two planar rigid walls on each side, is subject to a shear flow. Flow properties are then analyzed as a function of shear rate γ ˙, the concentration of the suspension ϕ , and the viscosity contrast λ =ηin/ηout , where ηin and ηout are the fluid viscosities of the inner and outer fluids, respectively. We find that the apparent (or effective viscosity) of the suspension exhibits both shear thinning (decreasing viscosity with shear rate) or shear thickening (increasing viscosity with shear rate) in the same concentration range. The shear thinning or thickening behaviors appear as subtle phenomena, dependant on viscosity contrast λ . We provide physical arguments on the origins of these behaviors.

  18. Effect of Boundary Condition on the Shear Behaviour of Rock Joints in the Direct Shear Test

    Bahaaddini, M.

    2017-05-01

    The common method for determination of the mechanical properties of the rock joints is the direct shear test. This paper aims to study the effect of boundary condition on the results of direct shear tests. Experimental studies undertaken in this research showed that the peak shear strength is mostly overestimated. This problem is more pronounced for steep asperities and under high normal stresses. Investigation of the failure mode of these samples showed that tensile cracks are generated at the boundary of sample close to the specimen holders and propagated inside the intact materials. In order to discover the reason of observed failure mechanism in experiments, the direct shear test was simulated using PFC2D. Results of numerical models showed that the gap zone size between the upper and lower specimen holders has a significant effect on the shear mechanism. For the high gap size, stresses concentrate at the vicinity of the tips of specimen holders and result in generation and propagation of tensile cracks inside the intact material. However, by reducing the gap size, stresses are concentrated on asperities, and damage of specimen at its boundary is not observed. Results of this paper show that understanding the shear mechanism of rock joints is an essential step prior to interpreting the results of direct shear tests.

  19. Internationale medier: Når sproget er den eneste forskel

    Andersen, Rune Saugmann

    2009-01-01

    forhandlingerne som formålet med dem. Det gør der ikke mere. Efter tusindvis af historier i dusinvis af førende aviser verden over ser det ud til at der kun er én historie tilbage: Det neo-liberale udviklingseventyr. For i perioden 2001-2006 – hvor jeg har analyseret pressedækningen i USA, Spanien, England......, Indien og Argentina – er der sket en bemærkelsesværdig ensretning af presseomtalen af forhandlingerne – i øvrigt sideløbende med at forhandlingerne er blevet stadig mere fastlåste. ...

  20. Harvard ER-2 OH laser-induced fluorescence instrument

    Wennberg, Paul O.; Anderson, James G.

    1994-01-01

    The Harvard ER-2 OH instrument is scheduled to be integrated into the NASA ER-2 high altitude aircraft ozone payload in August 1992. Design and fabrication is presently underway. This experiment is a descendant of a balloon borne instrument designed and built in the mid-1980s. The ER-2 instrument is being designed to measure OH and HO2 as part of the NASA ozone payload for the investigation of processes controlling the concentration of stratospheric ozone. Although not specifically designed to do so, it is hoped that valid measurements of OH and HO2 can be made in the remote free troposphere with this instrument.

  1. Design and implementation of a shearing apparatus for the experimental study of shear displacement in rocks

    Moore, Johnathan; Crandall, Dustin; Gill, Magdalena; Brown, Sarah; Tennant, Bryan

    2018-04-01

    Fluid flow in the subsurface is not well understood in the context of "impermeable" geologic media. This is especially true of formations that have undergone significant stress fluctuations due to injection or withdrawal of fluids that alters the localized pressure regime. When the pressure regime is altered, these formations, which are often already fractured, move via shear to reduce the imbalance in the stress state. While this process is known to happen, the evolution of these fractures and their effects on fluid transport are still relatively unknown. Numerous simulation and several experimental studies have been performed that characterize the relationship between shearing and permeability in fractures; while many of these studies utilize measurements of fluid flow or the starting and ending geometries of the fracture to characterize shear, they do not characterize the intermediate stages during shear. We present an experimental apparatus based on slight modifications to a commonly available Hassler core holder that allows for shearing of rocks, while measuring the hydraulic and mechanical changes to geomaterials during intermediate steps. The core holder modification employs the use of semi-circular end caps and structural supports for the confining membrane that allow for free movement of the sheared material while preventing membrane collapse. By integrating this modified core holder with a computed tomography scanner, we show a new methodology for understanding the interdependent behavior between fracture structure and flow properties during intermediate steps in shearing. We include a case study of this device function which is shown here through shearing of a fractured shale core and simultaneous observation of the mechanical changes and evolution of the hydraulic properties during shearing.

  2. Die HECT-Ligase Hul5, eine neue Komponente der ER-assoziierten Proteindegradation

    Kohlmann, Sonja

    2007-01-01

    Die meisten sekretorischen Proteine der eukaryontischen Zellen erreichen durch das endoplasmatische Retikulum (ER) den sekretorischen Signalweg. Sie gelangen vom Zytoplasma durch einen Kanal in der ER-Membran in das ER, wo sie ihre native Konformation erhalten. Das ER enthält ein strenges Qualitätskontrollsystem, welches fehlgefaltete Proteine erkennt, im ER zurückhält und letztendlich der ER-assoziierten Degradation (ERAD) zuführt. Die ER-Qualitätskontrolle und die ER-assoziierte Degradation...

  3. Chirality-specific lift forces of helix under shear flows: Helix perpendicular to shear plane.

    Zhang, Qi-Yi

    2017-02-01

    Chiral objects in shear flow experience a chirality-specific lift force. Shear flows past helices in a low Reynolds number regime were studied using slender-body theory. The chirality-specific lift forces in the vorticity direction experienced by helices are dominated by a set of helix geometry parameters: helix radius, pitch length, number of turns, and helix phase angle. Its analytical formula is given. The chirality-specific forces are the physical reasons for the chiral separation of helices in shear flow. Our results are well supported by the latest experimental observations. © 2016 Wiley Periodicals, Inc.

  4. Shear zones between rock units with no relative movement

    Koyi, H.; Schmeling, H.; Burchardt, S.

    2012-01-01

    , elongated bodies (vertical plates or horizontal rod-like bodies) produce tabular shear zones. Unlike conventional shear zones across which shear indicators ideally display consistent symmetries, shear indicators on either sides of the shear zone reported here show reverse kinematics. Thus profiles exhibit...... by progressive extension and (perhaps) where slabs of subducted oceanic lithosphere delaminate from the continental crust and sink into the asthenosphere. We also argue that such shear zones may be more common than they have been given the credit for and may be responsible for some of the kinematic reversals...

  5. Sigma-1 receptor chaperone at the ER-mitochondrion interface mediates the mitochondrion-ER-nucleus signaling for cellular survival.

    Tomohisa Mori

    Full Text Available The membrane of the endoplasmic reticulum (ER of a cell forms contacts directly with mitochondria whereby the contact is referred to as the mitochondrion-associated ER membrane or the MAM. Here we found that the MAM regulates cellular survival via an MAM-residing ER chaperone the sigma-1 receptor (Sig-1R in that the Sig-1R chaperones the ER stress sensor IRE1 to facilitate inter-organelle signaling for survival. IRE1 is found in this study to be enriched at the MAM in CHO cells. We found that IRE1 is stabilized at the MAM by Sig-1Rs when cells are under ER stress. Sig-1Rs stabilize IRE1 and thus allow for conformationally correct IRE1 to dimerize into the long-lasting, activated endonuclease. The IRE1 at the MAM also responds to reactive oxygen species derived from mitochondria. Therefore, the ER-mitochondrion interface serves as an important subcellular entity in the regulation of cellular survival by enhancing the stress-responding signaling between mitochondria, ER, and nucleus.

  6. Sigma-1 receptor chaperone at the ER-mitochondrion interface mediates the mitochondrion-ER-nucleus signaling for cellular survival.

    Mori, Tomohisa; Hayashi, Teruo; Hayashi, Eri; Su, Tsung-Ping

    2013-01-01

    The membrane of the endoplasmic reticulum (ER) of a cell forms contacts directly with mitochondria whereby the contact is referred to as the mitochondrion-associated ER membrane or the MAM. Here we found that the MAM regulates cellular survival via an MAM-residing ER chaperone the sigma-1 receptor (Sig-1R) in that the Sig-1R chaperones the ER stress sensor IRE1 to facilitate inter-organelle signaling for survival. IRE1 is found in this study to be enriched at the MAM in CHO cells. We found that IRE1 is stabilized at the MAM by Sig-1Rs when cells are under ER stress. Sig-1Rs stabilize IRE1 and thus allow for conformationally correct IRE1 to dimerize into the long-lasting, activated endonuclease. The IRE1 at the MAM also responds to reactive oxygen species derived from mitochondria. Therefore, the ER-mitochondrion interface serves as an important subcellular entity in the regulation of cellular survival by enhancing the stress-responding signaling between mitochondria, ER, and nucleus.

  7. Er3+ infrared fluorescence affected by spatial distribution synchronicity of Ba2+ and Er3+ in Er3+-doped BaO–SiO2 glasses

    Atsunobu Masuno

    2016-02-01

    Full Text Available Glasses with the composition xBaO–(99.9 − xSiO2–0.1ErO3/2 (0 ≤x ≤ 34.9 were fabricated by a levitation technique. The glasses in the immiscibility region were opaque due to chemical inhomogeneity, while the other glasses were colorless and transparent. The scanning electron microscope observations and electron probe microanalysis scan profiles revealed that more Er3+ ions were preferentially distributed in the regions where more Ba2+ ions existed in the chemically inhomogeneous glasses. The synchronicity of the spatial distributions of the two ions initially increased with increasing x and then decreased when the Ba2+ concentration exceeded a certain value. The peak shape and lifetime of the fluorescence at 1.55 μm depended on x as well as the spatial distribution of both ions. These results indicate that although ErOn polyhedra are preferentially coordinated with Ba2+ ions and their local structure is affected by the coordination of Ba2+, there is a maximum in the amount of Ba2+ ions that can coordinate ErOn polyhedra since the available space for Ba2+ ions is limited. These findings provide us with efficient ways to design the chemical composition of glasses with superior Er3+ fluorescence properties for optical communication network systems.

  8. Analysis of the Shear Behavior of Stubby Y-Type Perfobond Rib Shear Connectors for a Composite Frame Structure.

    Kim, Sang-Hyo; Kim, Kun-Soo; Lee, Do-Hoon; Park, Jun-Seung; Han, Oneil

    2017-11-22

    Shear connectors are used in steel beam-concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. Thus, this paper proposes stubby Y-type perfobond rib shear connectors, redefining the existing connectors, for composite frames of building structures; these were used to perform push-out tests. These shear connectors have relatively small ribs compared to the conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

  9. Electro-elastoviscous response of polyaniline functionalized nano-porous zeolite based colloidal dispersions.

    Chattopadhyay, Ankur; Rani, Poonam; Srivastava, Rajendra; Dhar, Purbarun

    2018-06-01

    The present article discusses the typical influence of grafted conducting polymers in the mesoscale pores of dielectric particles on the static and dynamic electrorheology and electro-viscoelastic behavior of corresponding colloids. Nanocrystalline meso-nanoporous zeolite has been prepared by chemical synthesis and subsequently polyaniline (PANI) coating has been implemented. Electrorheological (ER) suspensions have been formed by dispersing the nanoparticles in silicone oil and their viscoelastic behaviors are examined to understand the nature of such complex colloidal systems under electric fields. PANI-Zeolite ER fluids demonstrate higher static electroviscous effects and yield stress potential than untreated Zeolite, typically studied in literature. Transient electro-viscous characterizations show a stable and negligible hysteresis behavior when both the fluids are exposed to constant as well as time varying electric field intensities. Further oscillatory shear experiments of frequency and strain sweeps exhibit predominant elastic behavior in case of Zeolite based ER suspensions as compared to PANI systems. Detailed investigations reveal Zeolite based ER suspensions display enhanced relative yielding as well as electro-viscoelastic stability than the PANI-Zeolite. The steady state viscous behaviors are scaled against the non-dimensional Mason number to model the system behavior for both fluids. Experimental data of flow behaviors of both the ER fluids are compared with semi-classical models and it is found that the CCJ model possesses a closer proximity than traditional Bingham model, thereby revealing the fluids to be generic pseudo-linear fluids. The present article reveals that while the PANI based fluids are typically hailed superior in literature, it is only restricted to steady shear utilities. In case of dynamic and oscillatory systems, the traditional Zeolite based fluids exhibit superior ER caliber. Copyright © 2018 Elsevier Inc. All rights reserved.

  10. Lightweight concrete modification factor for shear friction.

    2013-10-01

    This report describes the results of a study initiated to examine the influence of concrete unit weight on the direct shear transfer across an interface of concretes cast at different times. This type of interface is common with structural precast co...

  11. Falling balls and simple shearing strain

    Brun, J L; Pacheco, A F

    2006-01-01

    The problem of particles falling under gravity allows us to relate Hamiltonian mechanics to such different subjects as elasticity and fluid mechanics. It is with this in mind that mechanics gives us the opportunity of introducing, in a rather simple and unusual form, some concepts such as vorticity, the incompressibility condition or simple shear strain to physics students at the undergraduate level

  12. Shear of ordinary and elongated granular mixtures

    Hensley, Alexander; Kern, Matthew; Marschall, Theodore; Teitel, Stephen; Franklin, Scott

    2015-03-01

    We present an experimental and computational study of a mixture of discs and moderate aspect-ratio ellipses under two-dimensional annular planar Couette shear. Experimental particles are cut from acrylic sheet, are essentially incompressible, and constrained in the thin gap between two concentric cylinders. The annular radius of curvature is much larger than the particles, and so the experiment is quasi-2d and allows for arbitrarily large pure-shear strains. Synchronized video cameras and software identify all particles and track them as they move from the field of view of one camera to another. We are particularly interested in the global and local properties as the mixture ratio of discs to ellipses varies. Global quantities include average shear rate and distribution of particle species as functions of height, while locally we investigate the orientation of the ellipses and non-affine events that can be characterized as shear transformational zones or possess a quadrupole signature observed previously in systems of purely circular particles. Discrete Element Method simulations on mixtures of circles and spherocylinders extend the study to the dynamics of the force network and energy dissipated as the system evolves. Supported by NSF CBET #1243571 and PRF #51438-UR10.

  13. Shear Adhesion of Tapered Nanopillar Arrays.

    Cho, Younghyun; Minsky, Helen K; Jiang, Yijie; Yin, Kaiyang; Turner, Kevin T; Yang, Shu

    2018-04-04

    Tapered nanopillars with various cross sections, including cone-shaped, stepwise, and pencil-like structures (300 nm in diameter at the base of the pillars and 1.1 μm in height), are prepared from epoxy resin templated by nanoporous anodic aluminum oxide (AAO) membranes. The effect of pillar geometry on the shear adhesion behavior of these nanopillar arrays is investigated via sliding experiments in a nanoindentation system. In a previous study of arrays with the same geometry, it was shown that cone-shaped nanopillars exhibit the highest adhesion under normal loading while stepwise and pencil-like nanopillars exhibit lower normal adhesion strength due to significant deformation of the pillars that occurs with increasing indentation depth. Contrary to the previous studies, here, we show that pencil-like nanopillars exhibit the highest shear adhesion strength at all indentation depths among three types of nanopillar arrays and that the shear adhesion increases with greater indentation depth due to the higher bending stiffness and closer packing of the pencil-like nanopillar array. Finite element simulations are used to elucidate the deformation of the pillars during the sliding experiments and agree with the nanoindentation-based sliding measurements. The experiments and finite element simulations together demonstrate that the shape of the nanopillars plays a key role in shear adhesion and that the mechanism is quite different from that of adhesion under normal loading.

  14. A Shear Banding Model for Penetration Calculations

    2000-04-01

    mechanism of strength reduction to zero within a shear band in three different steels, includ- ing AISI 4340 with RHC 44, which is reasonably similar to RHA...TECH LIB CHINA LAKE CA 93555-6001 CDR NAVAL SUR WAR CTR C S COFFEY PPARK FZERILLI CODE 4140 R K GARRET JR JMCKIRGAN TECH LIB 101 STRAUSS AVE

  15. Prediction of turbulent shear layers in turbomachines

    Bradshaw, P.

    1974-01-01

    The characteristics of turbulent shear layers in turbomachines are compared with the turbulent boundary layers on airfoils. Seven different aspects are examined. The limits of boundary layer theory are investigated. Boundary layer prediction methods are applied to analysis of the flow in turbomachines.

  16. Structural relaxation monitored by instantaneous shear modulus

    Olsen, Niels Boye; Dyre, Jeppe; Christensen, Tage Emil

    1998-01-01

    time definition based on a recently proposed expression for the relaxation time, where G [infinity] reflects the fictive temperature. All parameters entering the reduced time were determined from independent measurements of the frequency-dependent shear modulus of the equilibrium liquid....

  17. Shear localization and microstructure in coarse grained beta titanium alloy

    Wang, Bingfeng, E-mail: biw009@ucsd.edu [State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan (China); School of Materials Science and Engineering, Central South University, Changsha, Hunan (China); Department of Mechanical and Aerospace Engineering, University of California, San Diego, United States of America (United States); Key Lab of Nonferrous Materials, Ministry of Education, Central South University, Changsha, Hunan (China); Wang, Xiaoyan [State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan (China); School of Materials Science and Engineering, Central South University, Changsha, Hunan (China); Li, Zezhou [Department of Mechanical and Aerospace Engineering, University of California, San Diego, United States of America (United States); Ma, Rui [School of Materials Science and Engineering, Central South University, Changsha, Hunan (China); Zhao, Shiteng [Department of Mechanical and Aerospace Engineering, University of California, San Diego, United States of America (United States); Xie, Fangyu [State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan (China); School of Materials Science and Engineering, Central South University, Changsha, Hunan (China); Zhang, Xiaoyong [State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan (China)

    2016-01-15

    Adiabatic shear localization plays an important role in the deformation and failure of the coarse grained beta titanium alloy Ti-5 Al-5 Mo-5 V-1 Cr-1 Fe with grain size about 1 mm at high strain rate deformation. Hat shaped specimens with different nominal shear strains are used to induce the formation of shear bands under the controlled shock-loading experiments. The true stress in the specimens can reach about 1040 MPa where the strain is about 1.83. The whole shear localization process lasts about 35 μs. The microstructures within the shear band are investigated by optical microscopy, scanning electron microscopy / electron backscatter diffraction, and transmission electron microscopy. The results show that the width of the shear bands decreases with increasing nominal shear strain, and the grains in the transition region near the shear band are elongated along the shear band, and the core of the shear band consists of the ultrafine deformed grains with width of 0.1 μm and heavy dislocations. With the aims of accommodating the imposed shear strain and maintaining neighboring grain compatibility, the grain subdivision continues to take place within the band. A fiber texture is formed in the core of the shear band. The calculated temperature rise in the shear band can reach about 722 K. Dynamic recovery is responsible for the formation of the microstructure in coarse grained beta titanium alloy.

  18. Vibronic intensities for Er3+ in Cs2 NaErCl6

    Acevedo, R.; Navarro, G.; Meruane, T.

    2001-01-01

    In this current study, we have undertaken vibronic intensity calculations for the absorptions (( 4 I 15/2 ) Γ k ) → (( 4 I 13/2 ) Γ l ) of the Er 3+ in the Cs 2 NaErCl 6 elpasolite type system. This system is extremely complicated to handle from both a theoretical and an experimental viewpoints. This theoretical work shows that over an energy range of about 400 cm -1 , a substantial amount of transitions are likely to take place (about 100 transitions; twenty five of them are magnetic dipole allowed and seventy five are vibronically allowed). It is then a formidable task to identify and assign all of these transitions in a non-ambiguous way. Also the experimental evidence available for these absorptions is related to a total of about twenty lines in the luminescence spectrum of this system. The spectrum itself is very challenging and the superposition of spectral features is most likely to occur. A careful analysis of the calculated vibronic intensities and overall oscillator strengths for the various transitions indicates that the current model used is both flexible and appropriate to deal with this kind of systems. In a forthcoming paper, we will examine the rather unusual high intensity associated with the (( 4 I 15/2 ) Γ k ) → (( 4 S 3/2 ) Γ l ) excitations. (Author)

  19. Cargo Release from Polymeric Vesicles under Shear

    Yingying Guo

    2018-03-01

    Full Text Available In this paper we study the release of cargo from polymeric nano-carriers under shear. Vesicles formed by two star block polymers— A 12 B 6 C 2 ( A B C and A 12 B 6 A 2 ( A B A —and one linear block copolymer— A 14 B 6 ( A B , are investigated using dissipative particle dynamics (DPD simulations. A - and C -blocks are solvophobic and B -block is solvophilic. The three polymers form vesicles of different structures. The vesicles are subjected to shear both in bulk and between solvophobic walls. In bulk shear, the mechanisms of cargo release are similar for all vesicles, with cargo travelling through vesicle membrane with no preferential release location. When sheared between walls, high cargo release rate is only observed with A B C vesicle after it touches the wall. For A B C vesicle, the critical condition for high cargo release rate is the formation of wall-polymersome interface after which the effect of shear rate in promoting cargo release is secondary. High release rate is achieved by the formation of solvophilic pathway allowing cargo to travel from the vesicle cavity to the vesicle exterior. The results in this paper show that well controlled target cargo release using polymersomes can be achieved with polymers of suitable design and can potentially be very useful for engineering applications. As an example, polymersomes can be used as carriers for surface active friction reducing additives which are only released at rubbing surfaces where the additives are needed most.

  20. Spurious Shear in Weak Lensing with LSST

    Chang, C.; Kahn, S.M.; Jernigan, J.G.; Peterson, J.R.; AlSayyad, Y.; Ahmad, Z.; Bankert, J.; Bard, D.; Connolly, A.; Gibson, R.R.; Gilmore, K.; Grace, E.; Hannel, M.; Hodge, M.A.; Jee, M.J.; Jones, L.; Krughoff, S.; Lorenz, S.; Marshall, P.J.; Marshall, S.; Meert, A.

    2012-09-19

    The complete 10-year survey from the Large Synoptic Survey Telescope (LSST) will image {approx} 20,000 square degrees of sky in six filter bands every few nights, bringing the final survey depth to r {approx} 27.5, with over 4 billion well measured galaxies. To take full advantage of this unprecedented statistical power, the systematic errors associated with weak lensing measurements need to be controlled to a level similar to the statistical errors. This work is the first attempt to quantitatively estimate the absolute level and statistical properties of the systematic errors on weak lensing shear measurements due to the most important physical effects in the LSST system via high fidelity ray-tracing simulations. We identify and isolate the different sources of algorithm-independent, additive systematic errors on shear measurements for LSST and predict their impact on the final cosmic shear measurements using conventional weak lensing analysis techniques. We find that the main source of the errors comes from an inability to adequately characterise the atmospheric point spread function (PSF) due to its high frequency spatial variation on angular scales smaller than {approx} 10{prime} in the single short exposures, which propagates into a spurious shear correlation function at the 10{sup -4}-10{sup -3} level on these scales. With the large multi-epoch dataset that will be acquired by LSST, the stochastic errors average out, bringing the final spurious shear correlation function to a level very close to the statistical errors. Our results imply that the cosmological constraints from LSST will not be severely limited by these algorithm-independent, additive systematic effects.

  1. Modeller forudsiger klimarespons hos træer og buske

    Meilby, Henrik

    2015-01-01

    Modeller baseret på målinger af træer og buskes årringe afslører, hvilke klimatiske faktorer der lokalt er afgørende for deres vækst. Det kan hjælpe os med at forstå nogle af de ændringer, der sker i vegetationen, for eksempel i Grønland og i alpine områder. Med udgangspunkt i klimafrem- skrivnin......Modeller baseret på målinger af træer og buskes årringe afslører, hvilke klimatiske faktorer der lokalt er afgørende for deres vækst. Det kan hjælpe os med at forstå nogle af de ændringer, der sker i vegetationen, for eksempel i Grønland og i alpine områder. Med udgangspunkt i klimafrem...

  2. A Comparative Study of Er3+, Er3+-Eu3+, Er3+-Tb3+, and Er3+-Eu3+-Tb3+ Codoped Y2O3 Nanoparticles as Optical Heaters

    G. A. Sobral

    2015-01-01

    Full Text Available Fluorescence intensity ratio (FIR technique, based on the thermal coupling of H11/22 and S3/24 energy levels of erbium ions, was used to study the optical heating behavior of rare earth doped yttrium oxide nanophosphors (Y2O3:Er3+, Y2O3:Er3+-Eu3+, Y2O3:Er3+-Tb3+, and Y2O3:Er3+-Eu3+-Tb3+ synthesized via PVA-assisted sol-gel route. The samples were optically heated by an 800 nm CW diode laser, while the upconverted green emissions were used to measure their temperatures in real time. The experimental results indicate that the studied nanoparticles are promising candidates to applications such as photothermal treatments and hyperthermia.

  3. TCSP ER-2 LIGHTNING INSTRUMENT PACKAGE (LIP) V1

    National Aeronautics and Space Administration — The TCSP ER-2 Lightning Instrument Package (LIP) consists of 7 rotating vane type electric field sensors and a two channel conductivity probe along with a central...

  4. Hvor er nørderne, der skal sikre klimaomstillingen?

    Andersen, Frans Ørsted

    2015-01-01

    Kronikken skaber en forbindelse mellem vores nye forskningsprojekt, "Pædagogik på kanten" (som også er titlen på en ny bog, der udkom 6.11.15) og klimaproblemerne / behovet for klimaomstilling....

  5. TCSP ER-2 DOPPLER RADAR (EDOP) V1

    National Aeronautics and Space Administration — The EDOP provides vertically profiled reflectivity and Doppler velocity at aircraft nadir along the flight track. The ER-2 Doppler radar (EDOP) is an X-band (9.6...

  6. Biocompatible Er:(Na,K)NbO3 nanofibers

    Markova, N. P.; Grishin, A. M.

    2017-11-01

    Dense homogeneous fabric composed from continuous bead-free erbium-doped sodium potassium niobate (Er:NKN) 100 μm long and 100-200 nm in diameter nanofibers was sintered by sol-gel calcination assisted electrospinning technique. Er doping with the concentration of 2 at.% provides readily detectable room-temperature broad-band photoluminescence (PL) centered at λPL = 0.55 and 0.98 μm being pumped, respectively, with 532 and 785 nm lasers. Electric field induced resistance switching and strong electric rectification effect were found in nanoporous sandwich Au/Er:NKN/Pt capacitive cell. Memristor-type current-voltage I-V characteristics originate from the electrochemical migration of oxygen vacancies at the n-type Er:NKN oxide/high work function Pt cathode junction interface.

  7. Promoter and Cofactor Requirements for SERM-ER Activity

    Carroll, Jason S

    2007-01-01

    .... We originally planned to develop a methodology for specifically isolating chromatin to assess associated proteins but due to technical limitations we developed the ChiP-on-chip technique to map ER...

  8. Nuclear level density of 166Er with static deformation

    Nasrabadi, M.N.

    2006-01-01

    The level densities of 166 Er is calculated using the microscopic theory of interacting fermions and is compared with experimental. It is concluded that the data can be reproduced with level density formalism for nuclei with static deformation

  9. Ferske vandområder - Søer

    Jensen, J. P.; Jeppesen, E.; Søndergaard, M.

    Forord: Denne rapport er udarbej-det af Danmarks Mil-jøunder-søgelser som et led i den lands-dæk-ken-de rapportering af Vand-miljøpla-nens Over-vågningspro-gram. Over-vågningsprogram-met blev iværksat efteråret 1988. Hensigten med Vand-miljøplanens over-vågningsprogram er at undersøge effekten af......-miljøet med nærings-salte. Danmarks Miljøundersø-gelser har som sektor-forskningsinstitu-tion i Miljø- og Energiministeriet til opgave at forbedre og styrke det fagli-ge grundlag for de mil-jøpolitiske prioriteringer og beslut-ninger. En væsentlig del af denne opgave er overvågning af miljø og natur. Det er...

  10. High strength semi-active energy absorbers using shear- and mixedmode operation at high shear rates

    Becnel, Andrew C.

    This body of research expands the design space of semi-active energy absorbers for shock isolation and crash safety by investigating and characterizing magnetorheological fluids (MRFs) at high shear rates ( > 25,000 1/s) under shear and mixed-mode operation. Magnetorheological energy absorbers (MREAs) work well as adaptive isolators due to their ability to quickly and controllably adjust to changes in system mass or impact speed while providing fail-safe operation. However, typical linear stroking MREAs using pressure-driven flows have been shown to exhibit reduced controllability as impact speed (shear rate) increases. The objective of this work is to develop MREAs that improve controllability at high shear rates by using pure shear and mixed shear-squeeze modes of operation, and to present the fundamental theory and models of MR fluids under these conditions. A proof of concept instrument verified that the MR effect persists in shear mode devices at shear rates corresponding to low speed impacts. This instrument, a concentric cylinder Searle cell magnetorheometer, was then used to characterize three commercially available MRFs across a wide range of shear rates, applied magnetic fields, and temperatures. Characterization results are presented both as flow curves according to established practice, and as an alternate nondimensionalized analysis based on Mason number. The Mason number plots show that, with appropriate correction coefficients for operating temperature, the varied flow curve data can be collapsed to a single master curve. This work represents the first shear mode characterization of MRFs at shear rates over 10 times greater than available with commercial rheometers, as well as the first validation of Mason number analysis to high shear rate flows in MRFs. Using the results from the magnetorheometer, a full scale rotary vane MREA was developed as part of the Lightweight Magnetorheological Energy Absorber System (LMEAS) for an SH-60 Seahawk helicopter

  11. Er det økologisk madordninger ofte sundere?

    He, Chen

    Det europæiske skolemad system er under forandring, en forandring der er blevet kaldt den europæiske skolemad revolution af Morgan & Sonnino (2008). Forandringen består af to afgørende søjler/indsatsområder; 1) Krav til sundere kostvaner; 2) Flere økologiske fødevarer. Denne forskning harundersøg...

  12. Outdoor Adventure er mulighedernes læringslandskab

    Pedersen, Sune Ib Schou

    2014-01-01

    Global Nutrition and Health er en ny international uddannelse for ernærings- og sundhedsstuderende ved Professionshøjskolen Metropol. De tilbydes Outdoor Adventure, som bryder de vante rammer for undervisning.......Global Nutrition and Health er en ny international uddannelse for ernærings- og sundhedsstuderende ved Professionshøjskolen Metropol. De tilbydes Outdoor Adventure, som bryder de vante rammer for undervisning....

  13. Outdoor Adventure er mulighedernes læringslandskab

    Pedersen, Sune

    2015-01-01

    Global Nutrition and Health er en ny international uddannelse for ernærings- og sundhedsstuderende ved Professionshøjskolen Metropol. De tilbydes Outdoor Adventure, som bryder de vante rammer for undervisning.......Global Nutrition and Health er en ny international uddannelse for ernærings- og sundhedsstuderende ved Professionshøjskolen Metropol. De tilbydes Outdoor Adventure, som bryder de vante rammer for undervisning....

  14. "Det man hører, er man selv"

    Bonde, Lars Ole

    2015-01-01

    ”Det man hører, er man selv” er Danmarks Radios P3s yderst velkendte slogan. Det dukkede op i begyndelsen af (20)00erne som opfindsom og populær afspejling af en moderne forståelse af den rolle musik og medieforbrug spiller for den voksne dansker. Denne artikel handler ikke om P3 som musikkanal...

  15. A model for the generation and interconversion of ER morphologies

    Shemesh, Tom; Klemm, Robin W.; Romano, Fabian B.; Wang, Songyu; Vaughan, Joshua; Zhuang, Xiaowei; Tukachinsky, Hanna; Kozlov, Michael M.; Rapoport, Tom A.

    2014-01-01

    The endoplasmic reticulum (ER) is an important membrane-bound organelle in all eukaryotic cells. Depending on cell type and functional state, the ER membrane can adopt different morphologies, including a network of interconnected tubules, and sheets that can contain fenestrations or be stacked on top of each other. How these different morphologies are generated is unclear. Here, we present a comprehensive theoretical model that explains the formation and interconversion of virtually all known...

  16. Er Native Advertising en gråzone?

    Andersen, Lars Pynt

    2018-01-01

    Native advertising ser ud til at være den perfekte syntese mellem læsernes ønske om interessant indhold og annoncørers ønske om at komme tættere på kunderne. Men native advertising er også anklaget for at være fundamentalt uetisk i sin virkemåde, og måske er de gode oplevelser faktisk netop et...

  17. Measuring the Digital Divide with PingER

    Cottrell, L.

    2003-10-01

    We introduce the PingER project/toolkit and show its relevance to monitoring sites in developing countries. We then show results from PingER that illustrate the extent of the Digital Divide in terms of Internet performance between developed and developing regions, which developing regions are catching up, keeping up, or falling behind and the magnitude of the differences in performance between developed regions and developing regions.

  18. Det man tænker er man selv

    Rosenbaum, Philip

    2017-01-01

    I en tid, hvor ”det postfaktuelle samfund” er det mest populære udtryk øst for Valby bakke, er det vigtigt for de profaktuelle fanebærere at forstå, at fakta og evidens ikke i sig selv ændrer på folks opfattelse og holdninger. For at evidensbaserede argumenter skal få en vigtig position i samfund...

  19. Vækstplan DK er en snuptagsløsning

    Boje Rasmussen, Martin Møller

    2013-01-01

    Med Vækstplan DK har Helle Thorning-Schmidt glemt en socialdemokratisk kongstanke i ambitionen om at skyde hurtig genvej til genvalg. Planen er først og fremmest udtryk for kortsigtet finanspolitik og ikke langsigtet konkurrenceevnepolitik.......Med Vækstplan DK har Helle Thorning-Schmidt glemt en socialdemokratisk kongstanke i ambitionen om at skyde hurtig genvej til genvalg. Planen er først og fremmest udtryk for kortsigtet finanspolitik og ikke langsigtet konkurrenceevnepolitik....

  20. Nondimensional quasi-steady analysis of magnetorheological dampers utilizing a Herschel-Bulkley model with preyield viscosity

    John, Shaju; Wereley, Norman M.

    2003-07-01

    Dampers based on electrorheological (ER) and magnetorheolgical (MR) fluids can be analyzed under assumptions of quasi-steady, fully developed flow behavior. Models that have been used to characterize ER and MR dampers include the Bingham-plastic, the Herschel-Bulkley and biviscous models. In the Bingham-plastic and the Herschel-Bulkley models, the fluid exhibits rigid behavior in the preyield flow region. The difference between these two models lie in the modeling of the postyield behavior. In the case of the Bingham-plastic model, the postyield behavior is such that the shear stress is proportional to the shear rate. In contrast, the Herschel-Bulkley model assumes that the shear stress is proportional to a power law of the shearrate. In the biciscous model, the relationship between the shear stres and shear rate is linear in both the preyield and postyield regions with constant values of viscosities for the two regions. However, the preyield flow behavior exhibits a much high viscosity than that in the postyield. In the propose model, the assumption of preyield rigid behavior within the Herschel-Bulkley model has been relaxed while the postyield relationship based on the power law has been retained. Here the fluid undergoes Newtonian preyield viscous flow and has a non-Newtonian postyield behavior. Based on this model, we have analyzed the performance of a rectangular duct ER or MR valve. Typical results include shear stress and velocity profiles across the valve gap, equivalent damping and damping coefficients.

  1. Overvågning af orkidéer 2000

    Wind, P.

    resultaterne af orkidéovervågningen (Wind 2001). Hertil kommer præsentationen af projektet og dets resultater efter forløbet af de første tre år (Løjtnant 1991a) og en bearbejdning af projektets resultater for årene 1987-1995 (Wind 1997). I nærværende rapport undersøges skov-hullæbe for en eventuel sammenhæng...... mellem skudanlæggelsen udtrykt ved antallet af blomstrende og vegetative skud i et givet år og nedbørsmængder i august og september året før. Det er en udbredt antagelse at der er en sammenhæng mellem skudanlæggelse og mængden af nedbør det foregående år. Undersøgelser af skov-hullæbe populationer i...... truet og sårbar samt de to arter der er omfattet af Habitatdirektivets bilag 2. I 2000 kan det i forhold til 1999 konstateres at der i 15 bestande er optalt et øget antal skud. I 11 bestande er der noteret en nedgang i antallet af skud sammenlignet med optællingerne i 1999. Af disse er der 2 be...

  2. Analysis of erythema after Er:YAG laser skin resurfacing.

    Ko, Na Young; Ahn, Hyo-Hyun; Kim, Soo-Nam; Kye, Young-Chul

    2007-11-01

    Postoperative erythema can be expected to occur in every patient after laser resurfacing, and pigmentary disturbances may be related to the intensity and the duration of erythema. This study was undertaken to assess the clinical features of erythema, the factors that influence its duration, and the relation between the duration of erythema and the incidence of hyperpigmentation and hypopigmentation in skin of Asian persons after Er:YAG laser resurfacing. A total of 218 patients (skin phototypes III to V) were recruited and treated with a short-pulsed Er:YAG laser, a variable-pulsed Er:YAG laser, or a dual-mode Er:YAG laser for skin resurfacing. Clinical assessments were performed retrospectively using medical charts and serial photographs. Postoperative erythema was observed in all patients after Er:YAG laser resurfacing with a mean duration of 4.72 months. In 98.2% of patients, erythema faded completely within 12 months. Postinflammatory hyperpigmentation was observed in 38.1% of patients after Er:YAG laser resurfacing. Skin phototype, level of ablation, and depth of thermal damage caused by a long-pulsed laser appear to be important factors that affect the duration of erythema. Moreover, prolonged erythema was related to the risk of postinflammatory hyperpigmentation.

  3. A model for the generation and interconversion of ER morphologies.

    Shemesh, Tom; Klemm, Robin W; Romano, Fabian B; Wang, Songyu; Vaughan, Joshua; Zhuang, Xiaowei; Tukachinsky, Hanna; Kozlov, Michael M; Rapoport, Tom A

    2014-12-09

    The peripheral endoplasmic reticulum (ER) forms different morphologies composed of tubules and sheets. Proteins such as the reticulons shape the ER by stabilizing the high membrane curvature in cross-sections of tubules and sheet edges. Here, we show that membrane curvature along the edge lines is also critical for ER shaping. We describe a theoretical model that explains virtually all observed ER morphologies. The model is based on two types of curvature-stabilizing proteins that generate either straight or negatively curved edge lines (R- and S-type proteins). Dependent on the concentrations of R- and S-type proteins, membrane morphologies can be generated that consist of tubules, sheets, sheet fenestrations, and sheet stacks with helicoidal connections. We propose that reticulons 4a/b are representatives of R-type proteins that favor tubules and outer edges of sheets. Lunapark is an example of S-type proteins that promote junctions between tubules and sheets. In a tubular ER network, lunapark stabilizes three-way junctions, i.e., small triangular sheets with concave edges. The model agrees with experimental observations and explains how curvature-stabilizing proteins determine ER morphology.

  4. Herp enhances ER-associated protein degradation by recruiting ubiquilins

    Kim, Tae-Yeon; Kim, Eunmin; Yoon, Sungjoo Kim; Yoon, Jong-Bok

    2008-01-01

    ER-associated protein degradation (ERAD) is a protein quality control system of ER, which eliminates misfolded proteins by proteasome-dependent degradation and ensures export of only properly folded proteins from ER. Herp, an ER membrane protein upregulated by ER stress, is implicated in regulation of ERAD. In the present study, we show that Herp interacts with members of the ubiquilin family, which function as a shuttle factor to deliver ubiquitinated substrates to the proteasome for degradation. Knockdown of ubiquilin expression by small interfering RNA stabilized the ERAD substrate CD3δ, whereas it did not alter or increased degradation of non-ERAD substrates tested. CD3δ was stabilized by overexpressed Herp mutants which were capable of binding to ubiquilins but were impaired in ER membrane targeting by deletion of the transmembrane domain. Our data suggest that Herp binding to ubiquilin proteins plays an important role in the ERAD pathway and that ubiquilins are specifically involved in degradation of only a subset of ubiquitinated targets, including Herp-dependent ERAD substrates

  5. Shear bond strength and fracture analysis of human vs. bovine teeth.

    Stefan Rüttermann

    Full Text Available PURPOSE: To evaluate if bovine enamel and dentin are appropriate substitutes for the respective human hard tooth tissues to test shear bond strength (SBS and fracture analysis. MATERIALS AND METHODS: 80 sound and caries-free human erupted third molars and 80 freshly extracted bovine permanent central incisors (10 specimens for each group were used to investigate enamel and dentine adhesion of one 2-step self-etch (SE and one 3-step etch and rinse (E&R product. To test SBS the buccal or labial areas were ground plane to obtain appropriate enamel or dentine areas. SE and E&R were applied and SBS was measured prior to and after 500 thermocycles between +5 and +55°C. Fracture analysis was performed for all debonded areas. RESULTS: ANOVA revealed significant differences of enamel and dentin SBS prior to and after thermocycling for both of the adhesives. SBS- of E&R-bonded human enamel increased after thermocycling but SE-bonded did not. Bovine enamel SE-bonded showed higher SBS after TC but E&R-bonded had lower SBS. No differences were found for human dentin SE- or E&R-bonded prior to or after thermocycling but bovine dentin SE-bonded increased whereas bovine dentine E&R-bonded decreased. Considering the totalized and adhesive failures, fracture analysis did not show significances between the adhesives or the respective tooth tissues prior to or after thermocycling. CONCLUSION: Although SBS was different on human and bovine teeth, no differences were found for fracture analysis. This indicates that solely conducted SBS on bovine substrate are not sufficient to judge the perfomance of adhesives, thus bovine teeth are questionnable as a substrate for shear bond testing.

  6. Naesliden Project: direct shear tests of filled and unfilled joints

    Ludvig, B.

    1980-05-15

    Joints from the Naesliden mine have been tested in a small field shear box and in a large shear rig. The large shear rig is described in detail, and its ability to test joints with an area of 600 mc/sup 2/ at a maximum normal stress of up to 20 MPa is emphasized. The stiffness and shear strength of the discontinuities in the Naesliden mine is presented. The values estimated at direct shear tests are compared with results from in situ measurements and tests on drillcores. The results show that the in situ measurements give lower values for the shear resistance than the direct shear tests. Estimation of the normal stiffness for joints in drill cores gave much higher stiffness than the estimations in the shear rig.

  7. Shear stress and interleukin-8 (IL-8) on the proliferation ...

    Endothelial progenitor cells (EPCs) derived from bone marrow, are also found ... into tissues and neovascularization, the cells are exposed to fluid shear stress. ... Both shear stress and IL-8 can influence the process of EPCs repair in wound.

  8. Shear Wave Generation by Decoupled and Partially Coupled Explosions

    Stevens, Jeffry L; Xu, Heming; Baker, G. E

    2008-01-01

    The objective of this project is to investigate the sources of shear wave generation by decoupled and partially coupled explosions, and the differences in shear wave generation between tamped and decoupled explosions...

  9. Evaluation of size effect on shear strength of reinforced concrete ...

    of the longitudinal and the web reinforcement, shear span-to-depth ratio and the ... A simple equation for predicting the shear strength of reinforced concrete deep ..... AASHTO 2007 LRFD Bridge Design Specifications, American Association of ...

  10. Stress relaxation of shear in metals during shock loading

    Glazyrin, V.P.; Platova, T.M.

    1988-01-01

    Constructed determining equation, taking into account stress relaxation of shear, was used to calculate the evolution of plane shock waves of primary and secondary compression in metals. Values of shear stress and viscosity coefficient were

  11. Heat Treatment of Al 7075 for Ejection Seat Shear Wire

    Wong, Catherine

    1999-01-01

    .... Current lots of Al 6061 could not duplicate the double shear breaking load values and so it was attempted to achieve the required double shear breaking load in the Al 7075 alloy with a stable microstructure...

  12. To determine the slow shearing rate for consolidation drained shear box tests

    Jamalludin, Damanhuri; Ahmad, Azura; Nordin, Mohd Mustaqim Mohd; Hashim, Mohamad Zain; Ibrahim, Anas; Ahmad, Fauziah

    2017-08-01

    Slope failures always occur in Malaysia especially during the rainy seasons. They cause damage to properties and fatalities. In this study, a total of 24 one dimensional consolidation tests were carried out on soil samples taken from 16 slope failures in Penang Island and in Baling, Kedah. The slope failures in Penang Island are within the granitic residual soil while in Baling, Kedah they are situated within the sedimentary residual soil. Most of the disturbed soil samples were taken at 100mm depth from the existing soil surface while some soil samples were also taken at 400, 700 and 1000mm depths from the existing soil surface. They were immediately placed in 2 layers of plastic bag to prevent moisture loss. Field bulk density tests were also carried out at all the locations where soil samples were taken. The field bulk density results were later used to re-compact the soil samples for the consolidation tests. The objective of the research is to determine the slow shearing rate to be used in consolidated drained shear box for residual soils taken from slope failures so that the effective shear strength parameters can be determined. One dimensional consolidation tests were used to determine the slow shearing rate. The slow shearing rate found in this study to be used in the consolidated drained shear box tests especially for Northern Malaysian residual soils was 0.286mm/minute.

  13. Microstructural evolution of a model, shear-banding micellar solution during shear startup and cessation.

    López-Barrón, Carlos R; Gurnon, A Kate; Eberle, Aaron P R; Porcar, Lionel; Wagner, Norman J

    2014-04-01

    We present direct measurements of the evolution of the segmental-level microstructure of a stable shear-banding polymerlike micelle solution during flow startup and cessation in the plane of flow. These measurements provide a definitive, quantitative microstructural understanding of the stages observed during flow startup: an initial elastic response with limited alignment that yields with a large stress overshoot to a homogeneous flow with associated micellar alignment that persists for approximately three relaxation times. This transient is followed by a shear (kink) band formation with a flow-aligned low-viscosity band that exhibits shear-induced concentration fluctuations and coexists with a nearly isotropic band of homogenous, highly viscoelastic micellar solution. Stable, steady banding flow is achieved only after approximately two reptation times. Flow cessation from this shear-banded state is also found to be nontrivial, exhibiting an initial fast relaxation with only minor structural relaxation, followed by a slower relaxation of the aligned micellar fluid with the equilibrium fluid's characteristic relaxation time. These measurements resolve a controversy in the literature surrounding the mechanism of shear banding in entangled wormlike micelles and, by means of comparison to existing literature, provide further insights into the mechanisms driving shear-banding instabilities in related systems. The methods and instrumentation described should find broad use in exploring complex fluid rheology and testing microstructure-based constitutive equations.

  14. Flexible Micropost Arrays for Shear Stress Measurement

    Wohl, Christopher J.; Palmieri, Frank L.; Hopkins, John W.; Jackson, Allen M.; Connell, John W.; Lin, Yi; Cisotto, Alexxandra A.

    2015-01-01

    Increased fuel costs, heightened environmental protection requirements, and noise abatement continue to place drag reduction at the forefront of aerospace research priorities. Unfortunately, shortfalls still exist in the fundamental understanding of boundary-layer airflow over aerodynamic surfaces, especially regarding drag arising from skin friction. For example, there is insufficient availability of instrumentation to adequately characterize complex flows with strong pressure gradients, heat transfer, wall mass flux, three-dimensionality, separation, shock waves, and transient phenomena. One example is the acoustic liner efficacy on aircraft engine nacelle walls. Active measurement of shear stress in boundary layer airflow would enable a better understanding of how aircraft structure and flight dynamics affect skin friction. Current shear stress measurement techniques suffer from reliability, complexity, and airflow disruption, thereby compromising resultant shear stress data. The state-of-the-art for shear stress sensing uses indirect or direct measurement techniques. Indirect measurements (e.g., hot-wire, heat flux gages, oil interferometry, laser Doppler anemometry, small scale pressure drag surfaces, i.e., fences) require intricate knowledge of the studied flow, restrictive instrument arrangements, large surface areas, flow disruption, or seeding material; with smaller, higher bandwidth probes under development. Direct measurements involve strain displacement of a sensor element and require no prior knowledge of the flow. Unfortunately, conventional "floating" recessed components for direct measurements are mm to cm in size. Whispering gallery mode devices and Fiber Bragg Gratings are examples of recent additions to this type of sensor with much smaller (?m) sensor components. Direct detection techniques are often single point measurements and difficult to calibrate and implement in wind tunnel experiments. In addition, the wiring, packaging, and installation

  15. Establishing the transport properties of QCD with heavy ion reactions. Final Scientific Report for DE-FG02-07ER41524

    Teaney, Derek

    2008-01-01

    During the time period from 9/1/07 - 3/1/08 the principle investigator was awarded a federal grant from the Department of Energy (DE-FG02-07ER41524) to establish the transport properties of QCD through heavy ion reactions. A relativistic viscous hydrodynamic computer code was developed in 2+1 dimensions which is suitable for extracting the shear viscosity from available heavy ion data. In addition, the transport coefficients of heavy mesons in strongly coupled N = 4 plasmas were determined using the gauge gravity duality. These transport coefficients are suppressed by 1/N c 2 which stymied previous efforts to determine the kinetics of these mesons.

  16. AFM observation of OMVPE-grown ErP on InP substrates using a new organometal tris(ethylcyclopentadienyl)erbium (Er(EtCp)3)

    Akane, T.; Jinno, S.; Yang, Y.; Kuno, T.; Hirata, T.; Isogai, Y.; Watanabe, N.; Fujiwara, Y.; Nakamura, A.; Takeda, Y.

    2003-01-01

    ErP has been grown on InP(0 0 1) substrates by organometallic vapor phase epitaxy (OMVPE) using a new liquid organic Er source: tris(ethylcyclopentadienyl)erbium (Er(EtCp) 3 ). Morphological change of an ErP layer on InP(0 0 1) is investigated together with that of an overgrown capping InP layer. Optimum growth condition of InP causes islanding on over-monolayer-ErP. A relatively low overgrowth temperature of InP is a key factor for attaining complete capping coverage on ErP

  17. Research Status on Bonding Behavior of Prefabricated Concrete Shear Wall

    Wang, Donghui; Liu, Xudong; Wang, Sheng; Li, Shanshan

    2018-03-01

    Prefabricated shear wall structure adapts to the development and requirements of China’s residential industrialization. The key to the prefabricated concrete shear wall structure is the connection between the prefabricated members, where the reliability of the connection of the concrete joint is related to the overall performance and seismic effect of the structure. In this paper, the microstructures of the joint surface and shear properties are analysed, and the formula for calculating the shear strength of the joint is obtained.

  18. Experimental Investigation of Adiabatic Shear Banding at Different Impact Velocities

    1993-01-01

    plasticity and ASB’s is the Double-notch Shear specimen, it has been decided to use this concept in shear testing at medium and high strain rates...is the Double-notch Shear specimen. it has been decided to use this concept in shear testing at medium and high strain rates. Originally, Campbell...7] C. Fressengeas, Analyse dynamique 61asto-viscoplastique de l’h6tdrogdndit6 de la ddforma- tion plastique de cisalllement, Proc. Int. Conf. on

  19. Separate structure of two branches of sheared slab ηi mode and effects of plasma rotation shear in weak magnetic shear region

    Jiquan Li; Kishimoto, Y.; Tuda, T.

    2000-01-01

    The separate structure of two branches of the sheared slab η i mode near the minimum-q magnetic surface is analysed and the effects of plasma rotation shears are considered in the weak magnetic shear region. Results show that the separation condition depends on the non-monotonous q profile and the deviation of rational surface from the minimum-q surface. Furthermore, it is found that the diamagnetic rotation shear may suppress the perturbation of the sheared slab η i mode at one side of the minimum-q surface, the poloidal rotation shear from the sheared E-vector x B-vector flow has a similar role to the slab mode structure when it possesses a direction same as the diamagnetic shear. A plausible interrelation between the separate structures of the two branches of the sheared slab mode and the discontinuity or gap of the radially global structure of the drift wave near the minimum-q surface observed in the toroidal particle simulation (Kishimoto Y et al 1998 Plasma Phys. Control. Fusion 40 A663) is discussed. It seems to support such a viewpoint: the double or/and global branches of the sheared slab η i mode near the minimum-q surface may become a bridge to connect the radially global structures of the drift wave at two sides of the minimum-q surface and the discontinuity may originate from the separate structures of these slab modes for a flatter q profile. (author)

  20. Evaluation of size dependent design shear strength of reinforced ...

    to the development of the size dependent models on the shear strength in ... predict the diagonal cracking strength and the ultimate shear strength of RC ... ing strength of normal beams was by Zsutty (1968) based on the data base available without .... The comparison of the calculated shear strength of the beams is shown.

  1. Modified bond model for shear in slabs under concentrated loads

    Lantsoght, E.O.L.; Van der Veen, C.; De Boer, A.

    2015-01-01

    Slabs subjected to concentrated loads close to supports, as occurring for truck loads on slab bridges, are less studied than beams in shear or slab-column connections in punching. To predict the shear capacity for this case, the Bond Model for concentric punching shear was studied initially.

  2. Fluid Effects on Shear Waves in Finely Layered Porous Media

    Berryman, J G

    2004-01-01

    Although there are five effective shear moduli for any layered VTI medium, one and only one effective shear modulus for the layered system contains all the dependence of pore fluids on the elastic or poroelastic constants that can be observed in vertically polarized shear waves. Pore fluids can increase the magnitude the shear energy stored by this modulus by a term that ranges from the smallest to the largest shear moduli of the VTI system. But, since there are five shear moduli in play, the increase in shear energy overall is reduced by a factor of about 5 in general. We can therefore give definite bounds on the maximum increase of shear modulus, being about 20% of the permitted range, when gas is fully replaced by liquid. An attendant increase of density (depending on porosity and fluid density) by approximately 5 to 10% partially offsets the effect of this shear modulus increase. Thus, an increase of shear wave speed on the order of 5 to 10% is shown to be possible when circumstances are favorable - i.e., when the shear modulus fluctuations are large (resulting in strong anisotropy), and the medium behaves in an undrained fashion due to fluid trapping. At frequencies higher than seismic (such as sonic and ultrasonic waves for well-logging or laboratory experiments), short response times also produce the requisite undrained behavior and, therefore, fluids also affect shear waves at high frequencies by increasing rigidity

  3. Non-homogeneous flow profiles in sheared bacterial suspensions

    Samanta, Devranjan; Cheng, Xiang

    Bacterial suspensions under shear exhibit interesting rheological behaviors including the remarkable ``superfluidic'' state with vanishing viscosity at low shear rates. Theoretical studies have shown that such ``superfluidic'' state is linked with non-homogeneous shear flows, which are induced by coupling between nematic order of active fluids and hydrodynamics of shear flows. However, although bulk rheology of bacterial suspensions has been experimentally studied, shear profiles within bacterial suspensions have not been explored so far. Here, we experimentally investigate the flow behaviors of E. coli suspensions under planar oscillatory shear. Using confocal microscopy and PIV, we measure velocity profiles across gap between two shear plates. We find that with increasing shear rates, high-concentration bacterial suspensions exhibit an array of non-homogeneous flow behaviors like yield-stress flows and shear banding. We show that these non-homogeneous flows are due to collective motion of bacterial suspensions. The phase diagram of sheared bacterial suspensions is systematically mapped as functions of shear rates an bacterial concentrations. Our experiments provide new insights into rheology of bacterial suspensions and shed light on shear induced dynamics of active fluids. Chemical Engineering and Material Science department.

  4. Nongeometrically converted shear waves in marine streamer data

    Drijkoningen, G.G.; El Allouche, N.; Thorbecke, J.W.; Bada, G.

    2012-01-01

    Under certain circumstances, marine streamer data contain nongeometrical shear body wave arrivals that can be used for imaging. These shear waves are generated via an evanescent compressional wave in the water and convert to propagating shear waves at the water bottom. They are called

  5. Diagonal Cracking and Shear Strength of Reinforced Concrete Beams

    Zhang, Jin-Ping

    1997-01-01

    The shear failure of non-shear-reinforced concrete beams with normal shear span ratios is observed to be governed in general by the formation of a critical diagonal crack. Under the hypothesis that the cracking of concrete introduces potential yield lines which may be more dangerous than the ones...

  6. An ER protein functionally couples neutral lipid metabolism on lipid droplets to membrane lipid synthesis in the ER.

    Markgraf, Daniel F; Klemm, Robin W; Junker, Mirco; Hannibal-Bach, Hans K; Ejsing, Christer S; Rapoport, Tom A

    2014-01-16

    Eukaryotic cells store neutral lipids such as triacylglycerol (TAG) in lipid droplets (LDs). Here, we have addressed how LDs are functionally linked to the endoplasmic reticulum (ER). We show that, in S. cerevisiae, LD growth is sustained by LD-localized enzymes. When LDs grow in early stationary phase, the diacylglycerol acyl-transferase Dga1p moves from the ER to LDs and is responsible for all TAG synthesis from diacylglycerol (DAG). During LD breakdown in early exponential phase, an ER membrane protein (Ice2p) facilitates TAG utilization for membrane-lipid synthesis. Ice2p has a cytosolic domain with affinity for LDs and is required for the efficient utilization of LD-derived DAG in the ER. Ice2p breaks a futile cycle on LDs between TAG degradation and synthesis, promoting the rapid relocalization of Dga1p to the ER. Our results show that Ice2p functionally links LDs with the ER and explain how cells switch neutral lipid metabolism from storage to consumption. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

  7. An ER Protein Functionally Couples Neutral Lipid Metabolism on Lipid Droplets to Membrane Lipid Synthesis in the ER

    Daniel F. Markgraf

    2014-01-01

    Full Text Available Eukaryotic cells store neutral lipids such as triacylglycerol (TAG in lipid droplets (LDs. Here, we have addressed how LDs are functionally linked to the endoplasmic reticulum (ER. We show that, in S. cerevisiae, LD growth is sustained by LD-localized enzymes. When LDs grow in early stationary phase, the diacylglycerol acyl-transferase Dga1p moves from the ER to LDs and is responsible for all TAG synthesis from diacylglycerol (DAG. During LD breakdown in early exponential phase, an ER membrane protein (Ice2p facilitates TAG utilization for membrane-lipid synthesis. Ice2p has a cytosolic domain with affinity for LDs and is required for the efficient utilization of LD-derived DAG in the ER. Ice2p breaks a futile cycle on LDs between TAG degradation and synthesis, promoting the rapid relocalization of Dga1p to the ER. Our results show that Ice2p functionally links LDs with the ER and explain how cells switch neutral lipid metabolism from storage to consumption.

  8. ER signaling is activated to protect human HaCaT keratinocytes from ER stress induced by environmental doses of UVB

    Mera, Kentaro; Kawahara, Ko-ichi; Tada, Ko-ichi; Kawai, Kazuhiro; Hashiguchi, Teruto; Maruyama, Ikuro; Kanekura, Takuro

    2010-01-01

    Proteins are folded properly in the endoplasmic reticulum (ER). Various stress such as hypoxia, ischemia and starvation interfere with the ER function, causing ER stress, which is defined by the accumulation of unfolded protein (UP) in the ER. ER stress is prevented by the UP response (UPR) and ER-associated degradation (ERAD). These signaling pathways are activated by three major ER molecules, ATF6, IRE-1 and PERK. Using HaCaT cells, we investigated ER signaling in human keratinocytes irradiated by environmental doses of ultraviolet B (UVB). The expression of Ero1-Lα, an upstream signaling molecule of ER stress, decreased at 1-4 h after 10 mJ/cm 2 irradiation, indicating that the environmental dose of UVB-induced ER stress in HaCaT cells, without growth retardation. Furthermore, expression of intact ATF6 was decreased and it was translocated to the nuclei. The expression of XBP-1, a downstream molecule of IRE-1, which is an ER chaperone whose expression is regulated by XBP-1, and UP ubiquitination were induced by 10 mJ/cm 2 UVB at 4 h. PERK, which regulates apoptosis, was not phosphorylated. Our results demonstrate that UVB irradiation generates UP in HaCaT cells and that the UPR and ERAD systems are activated to protect cells from UVB-induced ER stress. This is the first report to show ER signaling in UVB-irradiated keratinocytes.

  9. Genome-wide association studies identify four ER negative-specific breast cancer risk loci

    Garcia-Closas, Montserrat; Couch, Fergus J.; Lindstrom, Sara; Michailidou, Kyriaki; Schmidt, Marjanka K.; Brook, Mark N.; Orr, Nick; Rhie, Suhn Kyong; Riboli, Elio; Feigelson, Heather S.; Le Marchand, Loic; Buring, Julie E.; Eccles, Diana; Miron, Penelope; Fasching, Peter A.; Brauch, Hiltrud; Chang-Claude, Jenny; Carpenter, Jane; Godwin, Andrew K.; Nevanlinna, Heli; Giles, Graham G.; Cox, Angela; Hopper, John L.; Bolla, Manjeet K.; Wang, Qin; Dennis, Joe; Dicks, Ed; Howat, Will J.; Schoof, Nils; Bojesen, Stig E.; Lambrechts, Diether; Broeks, Annegien; Andrulis, Irene L.; Guénel, Pascal; Burwinkel, Barbara; Sawyer, Elinor J.; Hollestelle, Antoinette; Fletcher, Olivia; Winqvist, Robert; Brenner, Hermann; Mannermaa, Arto; Hamann, Ute; Meindl, Alfons; Lindblom, Annika; Zheng, Wei; Devillee, Peter; Goldberg, Mark S.; Lubinski, Jan; Kristensen, Vessela; Swerdlow, Anthony; Anton-Culver, Hoda; Dörk, Thilo; Muir, Kenneth; Matsuo, Keitaro; Wu, Anna H.; Radice, Paolo; teo, Soo Hwang; Shu, Xiao-Ou; Blot, William; Kang, Daehee; Hartman, Mikael; Sangrajrang, Suleeporn; Shen, Chen-Yang; Southey, Melissa C.; Park, Daniel J.; Hammet, Fleur; Stone, Jennifer; Veer, Laura J. Van't; Rutgers, Emiel J.; Lophatananon, Artitaya; Stewart-Brown, Sarah; Siriwanarangsan, Pornthep; Peto, Julian; Schrauder, Michael G.; Ekici, Arif B.; Beckmann, Matthias W.; dos Santos Silva, Isabel; Johnson, Nichola; Warren, Helen; Tomlinson, Ian; Kerin, Michael J.; Miller, Nicola; Marme, Federick; Schneeweiss, Andreas; Sohn, Christof; Truong, Therese; Laurent-Puig, Pierre; Kerbrat, Pierre; Nordestgaard, Børge G.; Nielsen, Sune F.; Flyger, Henrik; Milne, Roger L.; Perez, Jose Ignacio Arias; Menéndez, Primitiva; Müller, Heiko; Arndt, Volker; Stegmaier, Christa; Lichtner, Peter; Lochmann, Magdalena; Justenhoven, Christina; Ko, Yon-Dschun; Muranen, Taru A.; Aittomäki, Kristiina; Blomqvist, Carl; Greco, Dario; Heikkinen, Tuomas; Ito, Hidemi; Iwata, Hiroji; Yatabe, Yasushi; Antonenkova, Natalia N.; Margolin, Sara; Kataja, Vesa; Kosma, Veli-Matti; Hartikainen, Jaana M.; Balleine, Rosemary; Tseng, Chiu-Chen; Berg, David Van Den; Stram, Daniel O.; Neven, Patrick; Dieudonné, Anne-Sophie; Leunen, Karin; Rudolph, Anja; Nickels, Stefan; Flesch-Janys, Dieter; Peterlongo, Paolo; Peissel, Bernard; Bernard, Loris; Olson, Janet E.; Wang, Xianshu; Stevens, Kristen; Severi, Gianluca; Baglietto, Laura; McLean, Catriona; Coetzee, Gerhard A.; Feng, Ye; Henderson, Brian E.; Schumacher, Fredrick; Bogdanova, Natalia V.; Labrèche, France; Dumont, Martine; Yip, Cheng Har; Taib, Nur Aishah Mohd; Cheng, Ching-Yu; Shrubsole, Martha; Long, Jirong; Pylkäs, Katri; Jukkola-Vuorinen, Arja; Kauppila, Saila; Knight, Julia A.; Glendon, Gord; Mulligan, Anna Marie; Tollenaar, Robertus A. E. M.; Seynaeve, Caroline M.; Kriege, Mieke; Hooning, Maartje J.; van den Ouweland, Ans M. W.; van Deurzen, Carolien H. M.; Lu, Wei; Gao, Yu-Tang; Cai, Hui; Balasubramanian, Sabapathy P.; Cross, Simon S.; Reed, Malcolm W. R.; Signorello, Lisa; Cai, Qiuyin; Shah, Mitul; Miao, Hui; Chan, Ching Wan; Chia, Kee Seng; Jakubowska, Anna; Jaworska, Katarzyna; Durda, Katarzyna; Hsiung, Chia-Ni; Wu, Pei-Ei; Yu, Jyh-Cherng; Ashworth, Alan; Jones, Michael; Tessier, Daniel C.; González-Neira, Anna; Pita, Guillermo; Alonso, M. Rosario; Vincent, Daniel; Bacot, Francois; Ambrosone, Christine B.; Bandera, Elisa V.; John, Esther M.; Chen, Gary K.; Hu, Jennifer J.; Rodriguez-Gil, Jorge L.; Bernstein, Leslie; Press, Michael F.; Ziegler, Regina G.; Millikan, Robert M.; Deming-Halverson, Sandra L.; Nyante, Sarah; Ingles, Sue A.; Waisfisz, Quinten; Tsimiklis, Helen; Makalic, Enes; Schmidt, Daniel; Bui, Minh; Gibson, Lorna; Müller-Myhsok, Bertram; Schmutzler, Rita K.; Hein, Rebecca; Dahmen, Norbert; Beckmann, Lars; Aaltonen, Kirsimari; Czene, Kamila; Irwanto, Astrid; Liu, Jianjun; Turnbull, Clare; Rahman, Nazneen; Meijers-Heijboer, Hanne; Uitterlinden, Andre G.; Rivadeneira, Fernando; Olswold, Curtis; Slager, Susan; Pilarski, Robert; Ademuyiwa, Foluso; Konstantopoulou, Irene; Martin, Nicholas G.; Montgomery, Grant W.; Slamon, Dennis J.; Rauh, Claudia; Lux, Michael P.; Jud, Sebastian M.; Bruning, Thomas; Weaver, Joellen; Sharma, Priyanka; Pathak, Harsh; Tapper, Will; Gerty, Sue; Durcan, Lorraine; Trichopoulos, Dimitrios; Tumino, Rosario; Peeters, Petra H.; Kaaks, Rudolf; Campa, Daniele; Canzian, Federico; Weiderpass, Elisabete; Johansson, Mattias; Khaw, Kay-Tee; Travis, Ruth; Clavel-Chapelon, Françoise; Kolonel, Laurence N.; Chen, Constance; Beck, Andy; Hankinson, Susan E.; Berg, Christine D.; Hoover, Robert N.; Lissowska, Jolanta; Figueroa, Jonine D.; Chasman, Daniel I.; Gaudet, Mia M.; Diver, W. Ryan; Willett, Walter C.; Hunter, David J.; Simard, Jacques; Benitez, Javier; Dunning, Alison M.; Sherman, Mark E.; Chenevix-Trench, Georgia; Chanock, Stephen J.; Hall, Per; Pharoah, Paul D. P.; Vachon, Celine; Easton, Douglas F.; Haiman, Christopher A.; Kraft, Peter

    2013-01-01

    Estrogen receptor (ER)-negative tumors represent 20-30% of all breast cancers, with a higher proportion occurring in younger women and women of African ancestry. The etiology and clinical behavior of ER-negative tumors are different from those of tumors expressing ER (ER positive), including

  10. Shear viscosity, cavitation and hydrodynamics at LHC

    Bhatt, Jitesh R.; Mishra, Hiranmaya; Sreekanth, V.

    2011-01-01

    We study evolution of quark-gluon matter in the ultrarelativistic heavy-ion collisions within the frame work of relativistic second-order viscous hydrodynamics. In particular, by using the various prescriptions of a temperature-dependent shear viscosity to the entropy ratio, we show that the hydrodynamic description of the relativistic fluid becomes invalid due to the phenomenon of cavitation. For most of the initial conditions relevant for LHC, the cavitation sets in very early stage. The cavitation in this case is entirely driven by the large values of shear viscosity. Moreover we also demonstrate that the conformal terms used in equations of the relativistic dissipative hydrodynamic can influence the cavitation time.

  11. Design Against Propagating Shear Failure in Pipelines

    Leis, B. N.; Gray, J. Malcolm

    Propagating shear failure can occur in gas and certain hazardous liquid transmission pipelines, potentially leading to a large long-burning fire and/or widespread pollution, depending on the transported product. Such consequences require that the design of the pipeline and specification of the steel effectively preclude the chance of propagating shear failure. Because the phenomenology of such failures is complex, design against such occurrences historically has relied on full-scale demonstration experiments coupled with empirically calibrated analytical models. However, as economic drivers have pushed toward larger diameter higher pressure pipelines made of tough higher-strength grades, the design basis to ensure arrest has been severely compromised. Accordingly, for applications where the design basis becomes less certain, as has occurred increasing as steel grade and toughness has increased, it has become necessary to place greater reliance on the use and role of full-scale testing.

  12. Internal shear cracking in bulk metal forming

    Christiansen, Peter; Nielsen, Chris Valentin; Bay, Niels Oluf

    2017-01-01

    This paper presents an uncoupled ductile damage criterion for modelling the opening and propagation of internal shear cracks in bulk metal forming. The criterion is built upon the original work on the motion of a hole subjected to shear with superimposed tensile stress triaxiality and its overall...... performance is evaluated by means of side-pressing formability tests in Aluminium AA2007-T6 subjected to different levels of pre-strain. Results show that the new proposed criterionis able to combine simplicity with efficiency for predicting the onset of fracture and the crack propagation path for the entire...... cracking to internal cracks formed undert hree-dimensional states of stress that are typical of bulk metal forming....

  13. Turbulent shear layers in confining channels

    Benham, Graham P.; Castrejon-Pita, Alfonso A.; Hewitt, Ian J.; Please, Colin P.; Style, Rob W.; Bird, Paul A. D.

    2018-06-01

    We present a simple model for the development of shear layers between parallel flows in confining channels. Such flows are important across a wide range of topics from diffusers, nozzles and ducts to urban air flow and geophysical fluid dynamics. The model approximates the flow in the shear layer as a linear profile separating uniform-velocity streams. Both the channel geometry and wall drag affect the development of the flow. The model shows good agreement with both particle image velocimetry experiments and computational turbulence modelling. The simplicity and low computational cost of the model allows it to be used for benchmark predictions and design purposes, which we demonstrate by investigating optimal pressure recovery in diffusers with non-uniform inflow.

  14. Structures and shear response of lipid monolayers

    Dutta, P.; Ketterson, J.B.

    1993-02-01

    This report discusses our work during the last 3 years using x-ray diffraction and shear measurements to study lipid monolayers (membranes). The report is divided into: (1) structure: phase diagram of saturated fatty acid Langmuir monolayers, effect of head group interactions, studies of transferred monolayers (LB films); (2) mechanical properties: fiber=optic capillary wave probe and centrosymmetric trough, mechanical behavior of heneicosanoic acid monolayer phases

  15. Motional Effect on Wall Shear Stresses

    Kock, Samuel Alberg; Torben Fründ, Ernst; Yong Kim, Won

    Atherosclerosis is the leading cause of death and severe disability. Wall Shear Stress (WSS), the stress exerted on vessel walls by the flowing blood is a key factor in the development of atherosclerosis. Computational Fluid Dynamics (CFD) is widely used for WSS estimations. Most CFD simulations...... are based on static models to ease computational burden leading to inaccurate estimations. The aim of this work was to estimate the effect of vessel wall deformations (expansion and bending) on WSS levels....

  16. Self-organization in circular shear layers

    Bergeron, K.; Coutsias, E.A.; Lynov, Jens-Peter

    1996-01-01

    Experiments on forced circular shear layers performed in both magnetized plasmas and in rotating fluids reveal qualitatively similar self-organization processes leading to the formation of patterns of coherent vortical structures with varying complexity. In this paper results are presented from...... both weakly nonlinear analysis and full numerical simulations that closely reproduce the experimental observations. Varying the Reynolds number leads to bifurcation sequences accompanied by topological changes in the distribution of the coherent structures as well as clear transitions in the total...

  17. Stent implantation influence wall shear stress evolution

    Bernad, S. I.; Totorean, A. F.; Bosioc, A. I.; Petre, I.; Bernad, E. S.

    2016-06-01

    Local hemodynamic factors are known affect the natural history of the restenosis critically after coronary stenting of atherosclerosis. Stent-induced flows disturbance magnitude dependent directly on the strut design. The impact of flow alterations around struts vary as the strut geometrical parameters change. Our results provide data regarding the hemodynamic parameters for the blood flow in both stenosed and stented coronary artery under physiological conditions, namely wall shear stress and pressure drop.

  18. Magnetic field reconnexion in a sheared field

    Ugai, M.

    1981-01-01

    A nonlinear development of the Petschek mode in a sheared magnetic field where there is a field component Bsub(z) along an X line is numerically studied. It is found that finite-amplitude intermediate waves, adjacent to the slow shock, may eventually stand in the quasi-steady configuration; on the other hand, the fundamental characteristics of the Petschek-mode development are scarcely influenced, either qualitatively or quantitatively, by the Bsub(z) field. (author)

  19. Bonding performance of universal adhesives to er,cr:YSGG laser-irradiated enamel.

    Ayar, Muhammet Kerim; Erdemir, Fatih

    2017-04-01

    Universal adhesives have been recently introduced for use as self-etch or etch-and-rinse adhesives depending on the dental substrate and clinical condition. However, their bonding effectiveness to laser-irradiated enamel is still not well-known. Thus, the aim of this study was to compare the shear bond strength (SBS) of universal adhesives (Single Bond Universal; Nova Compo-B Plus) applied to Er,Cr:YSGG laser-irradiated enamel with SBS of the same adhesives applied in self-etch and acid-etching modes, respectively. Crown segments of sixty bovine incisors were embedded into standardized acrylic blocks. Flattened enamel surfaces were prepared. Specimens were divided into six groups according to universal adhesives and application modes randomly (n = 10), as follows: Single Bond Universal/acid-etching mode; Nova Compo-B Plus/acid-etching mode; Single Bond Universal/self-etching mode; Nova Compo-B Plus/self-etching mode; and Single Bond Universal/Er,Cr:YSGG Laser-etching mode; Nova Compo-B Plus/Er,Cr:YSGG Laser-etching mode. After surface treatments, universal adhesives were applied onto surfaces. SBS was determined after storage in water for 24 h using a universal testing machine with a crosshead speed of 0.5 mm min -1 . Failure modes were evaluated using a stereomicroscope. Data was analyzed using two-way of analyses of variances (ANOVA) (p = 0.05). Two-way ANOVA revealed that adhesive had no effect on SBS (p = 0.88), but application mode significantly influenced SBS (p = 0.00). Acid-etching significantly increased SBS, whereas there are no significant differences between self-etch mode and laser-etching for both adhesives. The bond strength of universal adhesives may depend on application mode. Acid etching may significantly increase bond strength, while laser etching may provide similar bond strength when compared to self-etch mode. © 2016 Wiley Periodicals, Inc.

  20. Electrorheology for energy production and conservation

    Huang, Ke

    Recently, based on the physics of viscosity, we developed a new technology, which utilizes electric or magnetic fields to change the rheology of complex fluids to reduce the viscosity, while keeping the temperature unchanged. The method is universal and applicable to all complex fluids with suspended particles of nano-meter, submicrometer, or micrometer size. Completely different from the traditional viscosity reduction method, raising the temperature, this technology is energy-efficient, as it only requires small amount of energy to aggregate the suspended particles. In this thesis, we will first discuss this new technology in detail, both in theory and practice. Then, we will report applications of our technology to energy science research. Presently, 80% of all energy sources are liquid fuels. The viscosity of liquid fuels plays an important role in energy production and energy conservation. With an electric field, we can reduce the viscosity of asphalt-based crude oil. This is important and useful for heavy crude oil and off-shore crude oil production and transportation. Especially, since there is no practical way to raise the temperature of crude oil inside the deepwater pipelines, our technology may play a key role in future off-shore crude oil production. Electrorehology can also be used to reduce the viscosity of refinery fuels, such as diesel fuel and gasoline. When we apply this technology to fuel injection, the fuel droplets in the fuel atomization become smaller, leading to faster combustion in the engine chambers. As the fuel efficiency of internal combustion engines depends on the combustion speed and timing, the fast combustion produces much higher fuel efficiency. Therefore, adding our technology on existing engines improves the engine efficiency significantly. A theoretical model for the engine combustion, which explains how fast combustion improves the engine efficiency, is also presented in the thesis. As energy is the key to our national security, we believe that our technology is important and will have a strong impact on energy production and conversation in the future.