WorldWideScience

Sample records for shale mining in-situ

  1. Analysis of Applicability of Oil Shale for in situ Conversion

    OpenAIRE

    Martemyanov, Sergey Mikhailovich; Bukharkin, Andrey Andreevich; Koryashov, Iliya Aleksandrovich; Ivanov, Aleksey Alekseevich

    2016-01-01

    There are only a few substantial oil shale industries in the world, mainly because of the high cost of oilshale development relative to coal, oil and natural gas. Innovative approaches to oil shale processing could change this situation. Underground (or in situ) conversion could become a very useful technology, once an efficient way is found to prepare oil shale deposits for heating and to transfer heat into them. A new electrophysical method, which uses electrical treeing breakdown and resis...

  2. Chemically assisted in situ recovery of oil shale

    Energy Technology Data Exchange (ETDEWEB)

    Ramierz, W.F.

    1993-12-31

    The purpose of the research project was to investigate the feasibility of the chemically assisted in situ retort method for recovering shale oil from Colorado oil shale. The chemically assisted in situ procedure uses hydrogen chloride (HCl), steam (H{sub 2}O), and carbon dioxide (CO{sub 2}) at moderate pressure to recovery shale oil from Colorado oil shale at temperatures substantially lower than those required for the thermal decomposition of kerogen. The process had been previously examined under static, reaction-equilibrium conditions, and had been shown to achieve significant shale oil recoveries from powdered oil shale. The purpose of this research project was to determine if these results were applicable to a dynamic experiment, and achieve penetration into and recovery of shale oil from solid oil shale. Much was learned about how to perform these experiments. Corrosion, chemical stability, and temperature stability problems were discovered and overcome. Engineering and design problems were discovered and overcome. High recovery (90% of estimated Fischer Assay) was observed in one experiment. Significant recovery (30% of estimated Fischer Assay) was also observed in another experiment. Minor amounts of freed organics were observed in two more experiments. Penetration and breakthrough of solid cores was observed in six experiments.

  3. High voltage-power frequency electrical heating in-situ conversion technology of oil shale

    Science.gov (United States)

    Sun, Youhong; Yang, Yang; Lopatin, Vladimir; Guo, Wei; Liu, Baochang; Yu, Ping; Gao, Ke; Ma, Yinlong

    2014-05-01

    effective area for heating and heat transmitting;it has very good adaptability to the formation,the location and depth of the electrodes which can be adjusted according to the specific stratigraphic depth case;A positive(negative) electrode can be connected to multiple negative(positive) electrodes,and the arrangement of the positive and negative electrodes can be evaluated for improving the extraction efficiency.High voltage-power frequency electrical heating in-situ conversion technology is a very promising in-situ pyrolysis method,which could provide a new way of mining oil shale resources.

  4. Disposal of mine water from a deep oil shale mine

    Energy Technology Data Exchange (ETDEWEB)

    Sinor, J.E.

    1977-01-01

    A number of options were examined for the disposal of excess water from a deep room and pillar oil-shale mine. High fluoride levels in the water will prevent direct discharge. Evaporation via sprinkler irrigation was the least expensive option but could provide only limited capacity. Defluoridation via ion exchange was technically feasible but expensive. Reinjection into the major producing aquifer was the preferred solution. Computer simulations showed limited pressure effects due to reinjection.

  5. Explosive fragmentation of oil shale: Results from Colony and Anvil Points Mines, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Dick, R.D.; Fourney, W.L. [Maryland Univ., College Park, MD (United States). Dept. of Mechanical Engineering; Young, C. III [Sunburst Recovery, Inc., Steamboat Springs, CO (United States)

    1992-12-31

    From 1978 through 1983, numerous oil shale fragmentation tests were conducted at the Colony and Anvil Points Mines, Colorado. These experiments were part of an investigation to determine factors required for the adequate fragmentation of oil shale and to evaluate the feasibility of using the vertical modified in situ retort (VMIS) method for recovery of kerogen from oil shale. The objective of this research was to support the design of a large volume (10{sup 4} m{sup 3}) rubble bed for in situ processing. In addition, this rubble bed was to be formed in a large single-blast event which included decked charges, time delays, and multiple boreholes. Results are described.

  6. Gas seal for an in situ oil shale retort and method of forming thermal barrier

    Science.gov (United States)

    Burton, III, Robert S.

    1982-01-01

    A gas seal is provided in an access drift excavated in a subterranean formation containing oil shale. The access drift is adjacent an in situ oil shale retort and is in gas communication with the fragmented permeable mass of formation particles containing oil shale formed in the in situ oil shale retort. The mass of formation particles extends into the access drift, forming a rubble pile of formation particles having a face approximately at the angle of repose of fragmented formation. The gas seal includes a temperature barrier which includes a layer of heat insulating material disposed on the face of the rubble pile of formation particles and additionally includes a gas barrier. The gas barrier is a gas-tight bulkhead installed across the access drift at a location in the access drift spaced apart from the temperature barrier.

  7. Investigation of the Geokinetics horizontal in situ oil-shale-retorting process. Fourth annual report, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Hutchinson, D.L. (ed.)

    1981-03-01

    The Geokinetics in situ shale oil project is a cooperative venture between Geokinetics Inc. and the US Department of Energy. The objective is to develop a true in situ process for recovering shale oil using a fire front moving in a horizontal direction. The project is being conducted at a field site, Kamp Kerogen, located 70 miles south of Vernal, Utah. This Fourth Annual Report covers work completed during the calendar year 1980. During 1980 one full-size retort was blasted. Two retorts, blasted the previous year, were burned. A total of 4891 barrels of oil was produced during the year.

  8. Some implications of in situ uranium mining technology development

    Energy Technology Data Exchange (ETDEWEB)

    Cowan, C.E.; Parkhurst, M.A.; Cole, R.J.; Keller, D.; Mellinger, P.J.; Wallace, R.W.

    1980-09-01

    A technology assessment was initiated in March 1979 of the in-situ uranium mining technology. This report explores the impediments to development and deployment of this technology and evaluates the environmental impacts of a generic in-situ facility. The report is divided into the following sections: introduction, technology description, physical environment, institutional and socioeconomic environment, impact assessment, impediments, and conclusions. (DLC)

  9. Method for closing a drift between adjacent in situ oil shale retorts

    Science.gov (United States)

    Hines, Alex E.

    1984-01-01

    A row of horizontally spaced-apart in situ oil shale retorts is formed in a subterranean formation containing oil shale. Each row of retorts is formed by excavating development drifts at different elevations through opposite side boundaries of a plurality of retorts in the row of retorts. Each retort is formed by explosively expanding formation toward one or more voids within the boundaries of the retort site to form a fragmented permeable mass of formation particles containing oil shale in each retort. Following formation of each retort, the retort development drifts on the advancing side of the retort are closed off by covering formation particles within the development drift with a layer of crushed oil shale particles having a particle size smaller than the average particle size of oil shale particles in the adjacent retort. In one embodiment, the crushed oil shale particles are pneumatically loaded into the development drift to pack the particles tightly all the way to the top of the drift and throughout the entire cross section of the drift. The closure between adjacent retorts provided by the finely divided oil shale provides sufficient resistance to gas flow through the development drift to effectively inhibit gas flow through the drift during subsequent retorting operations.

  10. Influence of site-specific geology on oil shale fragmentation experiments at the Colony Mine, Garfield County, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Ray, J.M.; Harper, M.D.; Craig, J.L.; Edwards, C.L.

    1982-01-01

    The Los Alamos National Laboratory executed 19 intermediate scale cratering experiments in oil shale at the Colony Mine in Garfield County, Colorado. These experiments have led to a better understanding of fracture characteristics and fragmentation of in situ oil shale by use of a conventional high explosive. Geologic site characterization included detailed mapping, coring, and sample analyses. Site-specific geology was observed to be a major influence on the resulting crater geometry. The joint patterns at the experimental site frequently defined the final crater symmetry. Secondary influences included vugs, lithology changes, and grade fluctuations in the local stratigraphy. Most experiments, in both the rib and floor, were conducted to obtain data to investigate the fragmentation results within the craters. The rubble was screened for fragment-size distributions. Geologic features in proximity to the explosive charge had minimal effect on the rubble due to the overpowering effect of the detonation. However, these same features became more influential on the fracture and rubble characteristics with greater distances from the shothole. Postshot cores revealed a direct relationship between the grade of the oil shale and its susceptibility to fracturing. The Colony Mine experiments have demonstrated the significant role of geology in high explosive/oil shale interaction. It is probable that this role will have to be considered for larger applications to blast patterns and potential problems in retort stability in the future of oil shale development.

  11. OCCIDENTAL VERTICAL MODIFIED IN SITU PROCESS FOR THE RECOVERY OF OIL FROM OIL SHALE. PHASE II

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Reid M.

    1980-09-01

    The progress presented in this report covers the period June 1, 1980 through August 31, 1980 under the work scope for.Phase II of the DOE/Occidental Oil Shale, Inc. (OOSI) Cooperative Agreement. The major activities at OOSI 1s Logan Wash site during the quarter were: mining the voids at all levels for Retorts 7, 8 and 8x; completing Mini-Retort (MR) construction; continuing surface facility construction; tracer testing the MR 1 s; conducting Retorts 7 & 8 related Rock Fragmentation tests; setting up and debugging the Sandia B-61 trailer; and preparing the Phase II instrumentation plan.

  12. A review on in situ phytoremediation of mine tailings.

    Science.gov (United States)

    Wang, Li; Ji, Bin; Hu, Yuehua; Liu, Runqing; Sun, Wei

    2017-10-01

    Mine tailings are detrimental to natural plant growth due to their physicochemical characteristics, such as high pH, high salinity, low water retention capacity, high heavy metal concentrations, and deficiencies in soil organic matter and fertility. Thus, the remediation of mine tailings has become a key issue in environmental science and engineering. Phytoremediation, an in situ cost-effective technology, is emerging as the most promising remediation method for mine tailings by introducing tolerant plant species. It is particularly effective in dealing with large-area mine tailings with shallow contamination of organic, nutrient and metal pollutants. In this review, the background, concepts and applications of phytoremediation are comprehensively discussed. Furthermore, proper amendments used to improve the physical, chemical and biological properties of mine tailings are systematically reviewed and compared. Emphasis is placed on the types and characteristics of tolerant plants and their role in phytoremediation. Moreover, the role of microorganisms and their mechanism in phytoremediation are also discussed in-depth. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Effects of in-situ oil-shale retorting on water quality near Rock Springs, Wyoming, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Lindner-Lunsford, J.B.; Eddy, C.A.; Plafcan, M.; Lowham, H.W.

    1990-12-01

    Experimental in-situ retorting techniques (methods of extracting shale oil without mining) were used from 1969 to 1979 by the Department of Energy's (DOE) Laramie Energy Technology Center (LETC) at a test area near Rock Springs in southwestern Wyoming. The retorting experiments at site 9 have produced elevated concentrations of some contaminants in the ground water. During 1988 and 1989, the US Geological Survey, in cooperation with the US Department of Energy, conducted a site characterization study to evaluate the chemical contamination of ground water at the site. Water samples from 34 wells were analyzed; more than 70 identifiable organic compounds were detected using a combination of gas chromatography and mass spectrometry analytical methods. This report provides information that can be used to evaluate possible remedial action for the site. Remediation techniques that may be applicable include those techniques based on removing the contaminants from the aquifer and those based on immobilizing the contaminants. Before a technique is selected, the risks associated with the remedial action (including the no-action alternative) need to be assessed, and the criteria to be used for decisions regarding aquifer restoration need to be defined. 31 refs., 23 figs., 9 tabs.

  14. Method for explosive expansion toward horizontal free faces for forming an in situ oil shale retort

    Science.gov (United States)

    Ricketts, Thomas E.

    1980-01-01

    Formation is excavated from within a retort site in formation containing oil shale for forming a plurality of vertically spaced apart voids extending horizontally across different levels of the retort site, leaving a separate zone of unfragmented formation between each pair of adjacent voids. Explosive is placed in each zone, and such explosive is detonated in a single round for forming an in situ retort containing a fragmented permeable mass of formation particles containing oil shale. The same amount of formation is explosively expanded upwardly and downwardly toward each void. A horizontal void excavated at a production level has a smaller horizontal cross-sectional area than a void excavated at a lower level of the retort site immediately above the production level void. Explosive in a first group of vertical blast holes is detonated for explosively expanding formation downwardly toward the lower void, and explosive in a second group of vertical blast holes is detonated in the same round for explosively expanding formation upwardly toward the lower void and downwardly toward the production level void for forming a generally T-shaped bottom of the fragmented mass.

  15. Water Usage for In-Situ Oil Shale Retorting – A Systems Dynamics Model

    Energy Technology Data Exchange (ETDEWEB)

    Earl D. Mattson; Larry Hull; Kara Cafferty

    2012-12-01

    A system dynamic model was construction to evaluate the water balance for in-situ oil shale conversion. The model is based on a systems dynamics approach and uses the Powersim Studio 9™ software package. Three phases of an insitu retort were consider; a construction phase primarily accounts for water needed for drilling and water produced during dewatering, an operation phase includes the production of water from the retorting process, and a remediation phase water to remove heat and solutes from the subsurface as well as return the ground surface to its natural state. Throughout these three phases, the water is consumed and produced. Consumption is account for through the drill process, dust control, returning the ground water to its initial level and make up water losses during the remedial flushing of the retort zone. Production of water is through the dewatering of the retort zone, and during chemical pyrolysis reaction of the kerogen conversion. The major water consumption was during the remediation of the insitu retorting zone.

  16. Reliable practical technique for in-situ rock stress measurements in deep gold mines.

    CSIR Research Space (South Africa)

    Stacey, TR

    1998-03-01

    Full Text Available The proposed primary output of this research project is the development of a set of equipment and method of in situ stress measurements in a high stress environment typical of the deep level gold mines....

  17. MS Excel File describing groundwater quality for historic in situ recovery (ISR) uranium mines in Texas.

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — In situ recovery (ISR) uranium mining is a technique in which uranium is extracted by a series of injection and recovery wells developed in a permeable sandstone...

  18. Designing biochars for in situ remediation of metal contaminated mine spoils.

    Science.gov (United States)

    Biochar in conjunction with other soil amendments can be used for in situ remediation of metal-contaminated mine spoils for improved site phytostabilization. For successful phytostabilization to occur, biochar must improve mine spoil health with respect to plant rooting plus upt...

  19. Kinetics of selenium release in mine waste from the Meade Peak Phosphatic Shale, Phosphoria Formation, Wooley Valley, Idaho, USA

    Science.gov (United States)

    Lisa L. Stillings; Michael C. Amacher

    2010-01-01

    Phosphorite from the Meade Peak Phosphatic Shale member of the Permian Phosphoria Formation has been mined in southeastern Idaho since 1906. Dumps of waste rock from mining operations contain high concentrations of Se which readily leach into nearby streams and wetlands. While the most common mineralogical residence of Se in the phosphatic shale is elemental Se, Se(0...

  20. On the possibility of magnetic nano-markers use for hydraulic fracturing in shale gas mining

    Science.gov (United States)

    Zawadzki, Jaroslaw; Bogacki, Jan

    2016-04-01

    Recently shale gas production became essential for the global economy, thanks to fast advances in shale fracturing technology. Shale gas extraction can be achieved by drilling techniques coupled with hydraulic fracturing. Further increasing of shale gas production is possible by improving the efficiency of hydraulic fracturing and assessing the spatial distribution of fractures in shale deposits. The latter can be achieved by adding magnetic markers to fracturing fluid or directly to proppant, which keeps the fracture pathways open. After that, the range of hydraulic fracturing can be assessed by measurement of vertical and horizontal component of earth's magnetic field before and after fracturing. The difference in these components caused by the presence of magnetic marker particles may allow to delineate spatial distribution of fractures. Due to the fact, that subterranean geological formations may contain minerals with significant magnetic properties, it is important to provide to the markers excellent magnetic properties which should be also, independent of harsh chemical and geological conditions. On the other hand it is of great significance to produce magnetic markers at an affordable price because of the large quantities of fracturing fluids or proppants used during shale fracturing. Examining the properties of nano-materials, it was found, that they possess clearly superior magnetic properties, as compared to the same structure but having a larger particle size. It should be then possible, to use lower amount of magnetic marker, to obtain the same effect. Although a research on properties of new magnetic nano-materials is very intensive, cheap magnetic nano-materials are not yet produced on a scale appropriate for shale gas mining. In this work we overview, in detail, geological, technological and economic aspects of using magnetic nano-markers in shale gas mining. Acknowledgment This work was supported by the NCBiR under Grant "Electromagnetic method to

  1. Dow shale site tracer gas pressurization study. Final report. Appendix: energy from in situ processing of Antrim oil shale

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, E.W.; Lagus, P.L.

    1977-10-01

    A series of tracer gas pressurization experiments were undertaken at the Dow shale site at Peck, Michigan. The study was conducted to evaluate flow communication between boreholes open to both the Antrim and False Antrim layers of the retort volume, determine permeability and porosity distributions within the retort volume, and to assess qualitatively the uniformity of the fracturing or rubblization within the retort volume. Results show that the system is non-uniform. Flow from Well No. 4 to the other wells occurs primarily through various flow channels. These channels open when the wellhead pressure approaches the overburden pressure and appear closed at lower pressures. Consequently, the system is pressure sensitive and the flow is enhanced at elevated system pressures. Flow to outlying wells, such as No. 8 and No. 10, occurred only when Well No. 3 was at an elevated pressure. When the system approached steady state, as indicated by an absence of pressure changes, the production rate was about /sup 1///sub 3/ the injection rate. Multiple tracer gas injection into Well No. 4 at various depths demonstrated conclusively that flow does occur through the Antrim formation in the vicinity of Well No. 4. The permeability and porosity found in the vicinity of Well No. 4 was k approximately 0.045 millidarcy and phi approximately = 0.1 for a radius <1.75 ft and approximately 0.001 for radii greater than 1.75 ft. The major flow from Well No. 4 is toward Well No. 3, which in turn communicates readily with Wells No. 5 and No. 6. This flow occurs as a slug flow.

  2. Groundwater flow model of the Estonian oil shale mining area towards to innovative system

    Energy Technology Data Exchange (ETDEWEB)

    Lind, H. [Tallinn Univ. of Technology (Estonia). Dept. of Mining

    2010-07-01

    Changes in the Estonian groundwater regime are anticipated as oil shale deposits are mined. This paper described a dynamic groundwater flow model used to develop a 3-D groundwater elevation map of the Estonian oil shale mining area. The model was used to provide preliminary estimations of water inflow into the working underground mine areas. The model included 9 closed underground mines, 5 active mine sites, and 2 small open-cast sites. The closed mine sites were filled with water flowing in from the working mine sites. New mines and dewatering programs are planned for the future. A database from observation wells installed within the Keila-Kukruse aquifer was used to extract outputs and determine time steps. The model included 35 pumping stations from the active mine sites. The hydraulic properties for each model layer were defined in 4 model zones. Results of the model showed higher water in-flows from the closed underground sites than earlier predictions had anticipated. 9 refs., 1 tab., 4 figs.

  3. Geological settings of the protected Selisoo mire (northeastern Estonia threatened by oil shale mining

    Directory of Open Access Journals (Sweden)

    Helen Hiiemaa

    2014-05-01

    Full Text Available The protected Selisoo mire in northeastern Estonia is located above valuable oil shale resources, partly in the permitted mining area. We describe in detail the geomorphology and geological setting of the mire to understand the natural preconditions for its formation, development and preservation. We used the LiDAR-based digital elevation model for relief analysis, mapped the peat thickness with ground-penetrating radar and described the Quaternary cover through corings. Ridges, oriented perpendicular to the generally southward-sloping terrain, and shallow depressions at the surface of mineral soil have influenced mire formation and its spatio-temporal dynamics. The Quaternary cover under the mire is thin and highly variable. Therefore the mire is hydro­geologically insufficiently isolated from the limestone bedrock that is drained by the nearby oil shale mine and consequently the mining activities approaching the mire may have a negative influence on the wetland and proposed Natura 2000 site. Natura 2000 type wetlands, both protected or currently outside the nature reserves, cover a significant portion of the prospective oil shale mining areas. The distribution and resilience of those sites may significantly influence further utilization of oil shale resources.

  4. Investigation of the geokinetics horizontal in situ oil shale retorting process. Quarterly report, April, May, June 1980

    Energy Technology Data Exchange (ETDEWEB)

    Hutchinson, D.L.

    1980-08-01

    The Retort No. 18 burn was terminated on May 11, 1980. A total of 5547 barrels of shale oil or 46 percent of in-place resource was recovered from the retort. The EPA-DOE/LETC post-burn core sampling program is underway on Retort No. 16. Eleven core holes (of 18 planned) have been completed to date. Preliminary results indicate excellent core recovery has been achieved. Recovery of 702 ft of core was accomplished. The Prevention of Significant Deterioration (PSD) permit application was submitted to the EPA regional office in Denver for review by EPA and Utah air quality officials. The application for an Underground Injection Control (UIC) permit to authorize GKI to inject retort wastewater into the Mesa Verde Formation is being processed by the State of Utah. A hearing before the Board of Oil, Gas and Mining is scheduled in Salt Lake City, Utah, for July 22, 1980. Re-entry drilling on Retort No. 24 is progressing and placement of surface equipment is underway. Retort No. 25 blasthole drilling was completed and blast preparations are ongoing. Retort No. 25 will be blasted on July 18, 1980. The retort will be similar to Retort No. 24, with improvements in blasthole loading and detonation. US Patent No. 4,205,610 was assigned to GKI for a shale oil recovery process. Rocky Mountain Energy Company (RME) is evaluating oil shale holdings in Wyoming for application of the GKI process there.

  5. Rock Springs Site 12 hydraulic/explosive true in situ oil shale fracturing experiment

    Energy Technology Data Exchange (ETDEWEB)

    Parrish, R.L.; Boade, R.R.; Stevens, A.L.; Long, A. Jr.; Turner, T.F.

    1980-06-01

    The experiment plan involved the creation and characterization of three horizontal hydraulic fractures, followed by the insertion and simultaneous detonation of slurry explosive in the two lower fractures. Core analyses, wellbore logging, and airflow and /sup 85/Kr tracer tests were used for site characterization and assessment of the hydraulic and explosive fracturing. Tiltmeters, wellhead pressure and flow gages, and in-formation pressure, flow and crack-opening sensors were used to monitor hydrofracture creation and explosive insertion. Explosive detonation diagnostic data were taken with stress and time-of-arrival gages and surface and in-formation accelerometers. The post-fracturing assessments indicated that: (1) hydrofracture creation and explosive insertion and detonation were accomplished essentially as planned; (2) induced fractures were randomly distributed through the shale with no extensively fractured regions or dislocation of shale; and (3) enhancement of permeability was limited to enlargement of the explosive-filled fractures.

  6. Remote mining for in-situ waste containment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Martinelli, D.; Banta, L.; Peng, S. [and others

    1995-10-01

    This document presents the findings of a study conducted at West Virginia University to determine the feasibility of using a combination of longwall mining and standard landfill lining technologies to mitigate contamination of groundwater supplies by leachates from hazardous waste sites.

  7. BX in-situ oil-shale project. Quarterly technical progress report, June 1, 1981-August 31, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Dougan, P.M.

    1981-09-20

    June 1, 1981-August 31, 1981 was the third consecutive quarter of superheated steam injection at the BX In Situ Oil Shale Project. Injection was continuous except for the period of July 14th to August 1st when the injection was suspended during the drilling of core hole BX-37. During the quarter, 99,760 barrels of water as superheated steam were injected into Project injection wells at an average well head temperature of 752/sup 0/F and an average wellhead pressure of 1312 PSIG. During the same period, 135,469 barrels of fluid were produced from the Project production wells for a produced to injected fluid ratio of 1.36 to 1.0. Net oil production during the quarter was 38 barrels.

  8. Survey of active and inactive mines for possible use as in situ test facilities

    Energy Technology Data Exchange (ETDEWEB)

    1976-09-01

    A survey of active and inactive mines which might be useful for radioactive waste storage in situ test experiments was conducted. It was performed for Union Carbide Corporation, Nuclear Division, Office of Waste Isolation. The report covers available information gathered from literature, U.S. Bureau of Mines, the Mining Enforcement and Safety Agency, and a limited number of personal contacts with constructors or operators of facilities. This survey is preliminary in nature and the objective is to develop potential candidate facilities for in situ experiments which warrant further investigation. Included are descriptions of 244 facilities, with all the data about each one which was available within the time restraint of the study. These facility descriptions are additionally indexed by depth of mine, nature of the country rock, mineral mined, and type of entry. A total of 14 inactive mines and 34 active mines has been selected as those most worthy of further investigation for possible service as nuclear waste isolation test facilities. This investigation, being preliminary and having been performed in a very short time period, must be qualified, and the description of the qualification is presented in the body of this report. Qualifications deal primarily with the hazard of having omitted facilities and having incomplete data in some instances. Results indicate sedimentary rock mines of minerals of evaporite origin as a first ranking of preference for in situ testing, followed by other sedimentary rocks and then by mines producing minerals from any type rock where the mine is above the local water table. These are general rules and of course there can be exceptions to them.

  9. Flint mining in prehistory recorded by in situ-produced cosmogenic 10Be.

    Science.gov (United States)

    Verri, G; Barkai, R; Bordeanu, C; Gopher, A; Hass, M; Kaufman, A; Kubik, P; Montanari, E; Paul, M; Ronen, A; Weiner, S; Boaretto, E

    2004-05-25

    The development of mining to acquire the best raw materials for producing stone tools represents a breakthrough in human technological and intellectual development. We present a new approach to studying the history of flint mining, using in situ-produced cosmogenic 10Be concentrations. We show that the raw material used to manufacture flint artifacts approximately 300,000 years old from Qesem Cave (Israel) was most likely surface-collected or obtained from shallow quarries, whereas artifacts of the same period from Tabun Cave (Israel) were made of flint originating from layers 2 or more meters deep, possibly mined or quarried by humans.

  10. Microbial methane from in situ biodegradation of coal and shale: A review and reevaluation of hydrogen and carbon isotope signatures

    Science.gov (United States)

    Vinson, David S.; Blair, Neal E.; Martini, Anna M.; Larter, Steve; Orem, William H.; McIntosh, Jennifer C.

    2017-01-01

    Stable carbon and hydrogen isotope signatures of methane, water, and inorganic carbon are widely utilized in natural gas systems for distinguishing microbial and thermogenic methane and for delineating methanogenic pathways (acetoclastic, hydrogenotrophic, and/or methylotrophic methanogenesis). Recent studies of coal and shale gas systems have characterized in situ microbial communities and provided stable isotope data (δD-CH4, δD-H2O, δ13C-CH4, and δ13C-CO2) from a wider range of environments than available previously. Here we review the principal biogenic methane-yielding pathways in coal beds and shales and the isotope effects imparted on methane, document the uncertainties and inconsistencies in established isotopic fingerprinting techniques, and identify the knowledge gaps in understanding the subsurface processes that govern H and C isotope signatures of biogenic methane. We also compare established isotopic interpretations with recent microbial community characterization techniques, which reveal additional inconsistencies in the interpretation of microbial metabolic pathways in coal beds and shales. Collectively, the re-assessed data show that widely-utilized isotopic fingerprinting techniques neglect important complications in coal beds and shales.Isotopic fingerprinting techniques that combine δ13C-CH4 with δD-CH4 and/or δ13C-CO2have significant limitations: (1) The consistent ~ 160‰ offset between δD-H2O and δD-CH4 could imply that hydrogenotrophic methanogenesis is the dominant metabolic pathway in microbial gas systems. However, hydrogen isotopes can equilibrate between methane precursors and coexisting water, yielding a similar apparent H isotope signal as hydrogenotrophic methanogenesis, regardless of the actual methane formation pathway. (2) Non-methanogenic processes such as sulfate reduction, Fe oxide reduction, inputs of thermogenic methane, anaerobic methane oxidation, and/or formation water interaction can cause the apparent carbon

  11. Shale Failure Mechanics and Intervention Measures in Underground Coal Mines: Results From 50 Years of Ground Control Safety Research

    Science.gov (United States)

    Murphy, M. M.

    2016-02-01

    Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.

  12. Life cycle Greenhouse gas emissions of current Oil Sands Technologies: surface mining and in situ applications.

    Science.gov (United States)

    Bergerson, Joule A; Kofoworola, Oyeshola; Charpentier, Alex D; Sleep, Sylvia; Maclean, Heather L

    2012-07-17

    Life cycle greenhouse gas (GHG) emissions associated with two major recovery and extraction processes currently utilized in Alberta's oil sands, surface mining and in situ, are quantified. Process modules are developed and integrated into a life cycle model-GHOST (GreenHouse gas emissions of current Oil Sands Technologies) developed in prior work. Recovery and extraction of bitumen through surface mining and in situ processes result in 3-9 and 9-16 g CO(2)eq/MJ bitumen, respectively; upgrading emissions are an additional 6-17 g CO(2)eq/MJ synthetic crude oil (SCO) (all results are on a HHV basis). Although a high degree of variability exists in well-to-wheel emissions due to differences in technologies employed, operating conditions, and product characteristics, the surface mining dilbit and the in situ SCO pathways have the lowest and highest emissions, 88 and 120 g CO(2)eq/MJ reformulated gasoline. Through the use of improved data obtained from operating oil sands projects, we present ranges of emissions that overlap with emissions in literature for conventional crude oil. An increased focus is recommended in policy discussions on understanding interproject variability of emissions of both oil sands and conventional crudes, as this has not been adequately represented in previous studies.

  13. ANCHOR HILL PIT LAKE IN SITU TREATMENT, GILT EDGE MINE SUPERFUND SITE, S. DAKOTA, USA - A RETROSPECTIVE

    Science.gov (United States)

    The EPA Region VII Superfund office and the EPA National Risk Management Research Laboratory (NRMRL) Mine Waste Technology Program (MWTP)have been conducting a field scale technology demonstration of an in situ treatment of the Anchor Hill Pit Lake at the Gilt Edge Mine Superfund...

  14. {sup 13}C NMR and EPR spectroscopic evaluation of oil shale mined soil recuperation

    Energy Technology Data Exchange (ETDEWEB)

    Santos, J.V. dos, E-mail: mangrich@ufpr.br [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil); Mangrich, A.S. [Instituto Nacional de Ciencia e Tecnologia: Energia e Ambiente, Salvador, BA (Brazil); Pereira, B.F. [EMBRAPA Clima Temperado, Pelotas, RS (Brazil); Pillon, C.N. [EMBRAPA Clima Temperado, Pelotas, RS (Brazil). Estacao Experimental Cascata; Novotny, E.H. [EMBRAPA Solos, Rio de Janeiro, RJ (Brazil); Bonagamba, T.J. [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Instituto de Fisica; Abbt-Braun, G.; Frimmel, F.H. [Engler-Bunte-Institut, Universitaet Karlsruhe, TH (Germany)

    2013-02-15

    In this work, native forest soil (NFS) organic matter (SOM) sample and SOM samples from a neighboring forest soil area of an oil shale mine which is being rehabilitated for thirty years (RFS) were analyzed. X-band electron paramagnetic resonance (EPR) and solid-state {sup 13}C nuclear magnetic resonance (NMR) spectroscopies were used to evaluate the soil reclamation of the Brazilian oil shale mining process. Two-dimensional heterospectral correlation studies of the results obtained from EPRand {sup 13}C NMR were used to obtain information about SOM structures and their interactions with residual paramagnetic metal ion. The signal of the residual metallic oxycation, VO{sup 2+} correlated positively with uronic acid-type hydrophilic organic structures, determined from the {sup 13}C NMR spectra, and correlated negatively with the organic free radical (OFR) signal associated with oxygen atoms (g = 2.0042). The hydrophobic aromatic structures correlate positively with the EPR OFR signal associated with carbon atoms (g = 2.0022). The data from the two spectroscopic magnetic techniques show that the used recuperation process is effective. (author)

  15. Determination of contaminant levels and remediation efficacy in groundwater at a former in situ recovery uranium mine.

    Science.gov (United States)

    Borch, Thomas; Roche, Nicholas; Johnson, Thomas E

    2012-07-01

    There has been increasing interest in uranium mining in the United States via in situ recovery techniques. One of the main environmental concerns with in situ uranium mining is the potential for spreading groundwater contamination. There is a dearth of detailed analysis and information regarding the outcome of in situ uranium mine remediation to ascertain the environmental impacts. Regulatory measurements performed at a Wyoming in situ uranium mine were collected and analysed to ascertain the efficacy of remediation and potential long term environmental impact. Based on the measurements, groundwater sweeping followed by reverse osmosis (RO) treatment proved to be a highly efficient method of remediation. However, injection of a reductant in the form of H(2)S after groundwater sweeping and RO did not further reduce the aqueous concentration of U, Mn, or Fe. Low concentrations of target species at monitoring wells outside the mined area appear to indicate that in the long term, natural attenuation is likely to play a major role at reductively immobilizing residual (after remediation) concentrations of U(VI) thus preventing it from moving outside the mined area. Our analysis indicates the need for additional monitoring wells and sampling in conjunction with long term monitoring to better understand the impacts of the different remediation techniques.

  16. Minimum bed parameters for in situ processing of oil shale. Third quarterly report, April 1-June 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Tyner, C. E.

    1980-11-01

    Oil shale retort runs 028 (16% void) and 029 (7% void), composed of competent shale blocks plus shale rubble, were completed. Retort 028, processed with air at a flux of 0.017 kg/sub air//m/sup 2/ /sub shale/.second, had peak temperatures of 700/sup 0/C, a retorting rate of 1.1 m/day, and a yield of 82% FA. Retort 029, processed with air at a flux of 0.027 kg/sub air//m/sup 2//sub shale/.second, had peak temperatures of 750/sup 0/C, a retorting rate of 1.6 m/day, and a yield of 75% FA. Comparisons of retort model calculations with experimental data from previous retort run 027 (16% void, air flux of .029 kg/sub air//m/sup 2//sub shale/.second were good; observed experimental yield was 95% FA, calculated yield, 92.8%; experimental retorting rates varied from 9.5 to 8.9 cm/h, calculated rates from 10.3 to 10.0 cm/h; observed local heating rates ranged from 29 to 14/sup 0/C/h, calculated heating rates from 20 to 16/sup 0/C/h; and observed peak temperatures ranged from 815 to 825/sup 0/C, calculated from 820 to 825/sup 0/C.

  17. Factoring uncertainty into restoration modeling of in-situ leach uranium mines

    Science.gov (United States)

    Johnson, Raymond H.; Friedel, Michael J.

    2009-01-01

    Postmining restoration is one of the greatest concerns for uranium in-situ leach (ISL) mining operations. The ISL-affected aquifer needs to be returned to conditions specified in the mining permit (either premining or other specified conditions). When uranium ISL operations are completed, postmining restoration is usually achieved by injecting reducing agents into the mined zone. The objective of this process is to restore the aquifer to premining conditions by reducing the solubility of uranium and other metals in the ground water. Reactive transport modeling is a potentially useful method for simulating the effectiveness of proposed restoration techniques. While reactive transport models can be useful, they are a simplification of reality that introduces uncertainty through the model conceptualization, parameterization, and calibration processes. For this reason, quantifying the uncertainty in simulated temporal and spatial hydrogeochemistry is important for postremedial risk evaluation of metal concentrations and mobility. Quantifying the range of uncertainty in key predictions (such as uranium concentrations at a specific location) can be achieved using forward Monte Carlo or other inverse modeling techniques (trial-and-error parameter sensitivity, calibration constrained Monte Carlo). These techniques provide simulated values of metal concentrations at specified locations that can be presented as nonlinear uncertainty limits or probability density functions. Decisionmakers can use these results to better evaluate environmental risk as future metal concentrations with a limited range of possibilities, based on a scientific evaluation of uncertainty.

  18. Investigation of the geokinetics horizontal in situ oil shale retorting process. Quarterly report, January, February, March 1981

    Energy Technology Data Exchange (ETDEWEB)

    Hutchinson, D.L.

    1981-05-01

    Retort No. 23 has been heavily instrumented and was ignited on March 16, 1981. A total of 6588 barrels of shale oil have been recovered from Retort No. 24 to date; 6057 barrels of oil were recovered during the quarter, an average of 65 barrels per day. Approximately 4909 barrels of shale oil were shipped by tanker truck to the WESRECO refinery in Salt Lake City, Utah, during the quarter. Drilling of re-entry process and instrumentation wells on Retort No. 25 was completed. A post-burn core sampling program for Retort No. 18 was developed and implemented.

  19. 76 FR 21401 - Notice of Availability of the Draft EIS for the HB In-Situ Solution Mine Project, Eddy County, NM

    Science.gov (United States)

    2011-04-15

    ... BLM initiated the NEPA process for the HB In-Situ Solution Mine Project by preparing an environmental... Bureau of Land Management Notice of Availability of the Draft EIS for the HB In-Situ Solution Mine.... SUMMARY: In accordance with the National Environmental Policy Act of 1969, as amended (NEPA), the Bureau...

  20. Aquifer restoration at in-situ leach uranium mines: evidence for natural restoration processes

    Energy Technology Data Exchange (ETDEWEB)

    Deutsch, W.J.; Serne, R.J.; Bell, N.E.; Martin, W.J.

    1983-04-01

    Pacific Northwest Laboratory conducted experiments with aquifer sediments and leaching solution (lixiviant) from an in-situ leach uranium mine. The data from these laboratory experiments and information on the normal distribution of elements associated with roll-front uranium deposits provide evidence that natural processes can enhance restoration of aquifers affected by leach mining. Our experiments show that the concentration of uranium (U) in solution can decrease at least an order of magnitude (from 50 to less than 5 ppM U) due to reactions between the lixiviant and sediment, and that a uranium solid, possibly amorphous uranium dioxide, (UO/sub 2/), can limit the concentration of uranium in a solution in contact with reduced sediment. The concentrations of As, Se, and Mo in an oxidizing lixiviant should also decrease as a result of redox and precipitation reactions between the solution and sediment. The lixiviant concentrations of major anions (chloride and sulfate) other than carbonate were not affected by short-term (less than one week) contact with the aquifer sediments. This is also true of the total dissolved solids level of the solution. Consequently, we recommend that these solution parameters be used as indicators of an excursion of leaching solution from the leach field. Our experiments have shown that natural aquifer processes can affect the solution concentration of certain constituents. This effect should be considered when guidelines for aquifer restoration are established.

  1. Occidental vertical modified in situ process for the recovery of oil from oil shale, Phase 2. Construction, operation, testing, and environmental impact. Final report, August 1981-December 1982. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, A.L.; Zahradnik, R.L.; Kaleel, R.J.

    1984-01-01

    Occidential Oil Shale, Inc. (OOSI) recently completed the demonstration of mining, rubblization, ignition, and simulataneous processing of two commericalized modified in situ (MIS) retorts at the Logas Wash facility near DeBeque, Colorado. Upon completion of Retort 6 in 1978, Occidential began incorporating all of the knowledge previously acquired in an effort to design two more commercial-sized MIS retorts. Any commercial venture of the future would require the ability to operate simultaneously more than one retort. Thus, Retorts 7 and 8 were developed during 1980 and 1981 through joint funding of the DOE and OOSI in Phase II. Rubblization of the retorts produced an average rubble void of 18.5% in the low grade shale (17 gallons per ton) at the Logan Wash site. After rubblization, bulkheads were constructed, inlet and offgas pipes were installed and connected to surface processing facilities and liquid product handling systems were connected to the retorts. Extensive instrumentation was installed in cooperation with Sandia National Laboratories for monitoring the complete operation of the retorts. After pre-ignition testing, Retort 8 was ignited in December of 1981 and Retort 7 was ignited in January of 1982. The retorts were operated without interruption from ignition until mid- November of 1982 at which time inlet gas injection was terminated and water quenching was begun. Total product yield from the two retorts was approximately 200,000 barrels of oil, or 70% of the Fischer Assay oil-in-place in the rubblized rock in the two retrots. Water quenching studies were conducted over a period of several months, with the objective of determining the rate of heat extraction from the retorts as well as determining the quantity and quality of offgas and water coming out from the quenching process. Data from these studies are also included in this Summary Report. 62 figs., 18 tabs.

  2. Processing use, and characterization of shale oil products

    Science.gov (United States)

    Decora, Andrew W.; Kerr, Robert D.

    1979-01-01

    Oil shale is a potential source of oil that will supplement conventional sources for oil as our needs for fossil fuels begin to exceed our supplies. The resource may be mined and processed on the surface or it may be processed in situ. An overview of the potential technologies and environmental issues is presented. PMID:446454

  3. Field Evaluation of the Restorative Capacity of the Aquifer Downgradient of a Uranium In-Situ Recovery Mining Site

    Energy Technology Data Exchange (ETDEWEB)

    Reimus, Paul William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-05-22

    A two-part field study was conducted in Smith Ranch-Highland in-situ recovery (ISR) near Douglas, Wyoming, to evaluate the restorative capacity of the aquifer downgradient (i.e., hydrologically downstream) of a Uranium ISR mining site with respect to the transport of uranium and other potential contaminants in groundwater after mining has ceased. The study was partially conducted by checking the Uranium content and the alkalinity of separate wells, some wells had been restored and others had not. A map and in-depth procedures of the study are included.

  4. DETERMINATION OF OPTIMAL CONTOURS OF OPEN PIT MINE DURING OIL SHALE EXPLOITATION, BY MINEX 5.2.3. PROGRAM

    Directory of Open Access Journals (Sweden)

    Miroslav Ignjatović

    2013-04-01

    Full Text Available By examination and determination of optimal solution of technological processes of exploitation and oil shale processing from Aleksinac site and with adopted technical solution and exploitation of oil shale, derived a technical solution that optimize contour of the newly defined open pit mine. In the world, this problem is solved by using a computer program that has become the established standard for quick and efficient solution for this problem. One of the computer’s program, which can be used for determination of the optimal contours of open pit mines is Minex 5.2.3. program, produced in Australia in the Surpac Minex Group Pty Ltd Company, which is applied at the Mining and Metallurgy Institute Bor (no. of licenses are SSI - 24765 and SSI - 24766. In this study, authors performed 11 optimization of deposit geo - models in Minex 5.2.3. based on the tests results, performed in a laboratory for soil mechanics of Mining and Metallurgy Institute, Bor, on samples from the site of Aleksinac deposits.

  5. Minimum bed parameters for in situ processing of oil shale. First quarterly report, October 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Tyner, C. E.

    1980-01-01

    To minimize the costs and environmental impact associated with the material removal involved in in-situ processing, it is important to determine the minimum conditions (of void, permeability, etc.) actually required for a viable in situ process. This problem is being investigated through laboratory studies and mathematical modeling. The laboratory program this quarter centered around design, fabrication, and initial testing of a new retort vessel and system. Model calculations were made with Sandia's block retorting code in this geometry to determine the most appropriate operating conditions for the run. The ignition heater design used in the first attempt to ignite the sample was unsatisfactory, and, as a result, sustained combustion was not achieved.

  6. Understanding anisotropic mechanical properties of shales at different length scales: In situ micropillar compression combined with finite element calculations

    Science.gov (United States)

    Keller, Lukas M.; Schwiedrzik, Jakob J.; Gasser, Philippe; Michler, Johann

    2017-08-01

    From microstructural observations and experimental work it is known that shales consist of a mechanically weak porous fine-grained clay matrix with embedded and mechanically strong silt/sand grains. Thereby, the respective contents of weak and strong constituents control bulk mechanical properties. In addition, the clay matrix is characterized by a preferred orientation of clay platelets, which are a major control on the bulk anisotropy of shales. To date, little is known about the micromechanical properties of the fine-grained porous clay matrix, which is particularly true in case of its micromechanical anisotropy. Such information can, however, only be assessed on the microscale. Therefore, the drained micromechanical properties parallel and perpendicular to bedding were investigated by means of compressing micropillars with a flat punch indenter in a scanning electron microscope. Microscopic failure mechanism was found to be anisotropic: (i) in case loading was parallel to bedding it occurred by a combination of localized shearing, kinking/buckling of elongated clay aggregates, and bedding parallel splitting and (ii) for loading perpendicular to bedding failure occurred mainly by localized shearing. The measured stiffness of the drained porous clay matrix perpendicular (Ev) and parallel (Eh) to bedding was about 8 GPa and 30 GPa, respectively. Using these stiffness values as input in voxel-based finite element modeling and in combination with realistic microstructures, which are characterized with different contents of "soft" and "hard" constituents, revealed that the measured high microscale anisotropy Eh/Ev = 3.75 is crucial in understanding the bulk anisotropy of clay rocks.

  7. Environmental research plan for the Geokinetics Inc. investigation of the horizontal in situ oil shale retorting process

    Energy Technology Data Exchange (ETDEWEB)

    Spradlin, H.K.L.; Hutchinson, D.L.; Mankowski, S.G.

    1979-11-30

    The development of a horizontal in-situ retorting process may have significant impacts upon valuable environmental resources. A research program has been developed to identify, assess, and minimize the adverse environmental impacts which may result. The goals are to: describe the environment as it existed prior to disturbance; determine the nature and extent of the changes; develop and implement measures to minimize the adverse impacts; develop and implement reclamation procedures which will return the affected land to its original level; and coordinate measures to protect the health and safety of persons and animals which may be affected by the activities. Specific research areas are outlined. These include atmospheric, hydrologic, terrestrial ecology, and social/economic research. (DMC)

  8. Monitoring in situ deformation induced by a fluid injection in a fault zone in shale using seismic velocity changes

    Science.gov (United States)

    Rivet, D.; De Barros, L.; Guglielmi, Y.; Castilla, R.

    2015-12-01

    We monitor seismic velocity changes during an experiment at decametric scale aimed at artificially reactivate a fault zone by a high-pressure hydraulic injection in a shale formation of the underground site of Tournemire, South of France. A dense and a multidisciplinary instrumentation, with measures of pressure, fluid flow, strain, seismicity, seismic properties and resistivity allow for the monitoring of this experiment. We couple hydromechanical and seismic observations of the fault and its adjacent areas to better understand the deformation process preceding ruptures, and the role played by fluids. 9 accelerometers recorded repeated hammers shots on the tunnel walls. For each hammer shot we measured small travel time delays on direct P and S waves. We then located the seismic velocity perturbations using a tomography method. At low injection pressure, i.e. P< 15 Bars, we observe an increase of P-waves velocity around the injection, while we measure no change in S waves velocity. When the pressure overcomes 15 Bars, velocity perturbations dramatically increase with both P and S waves affected. A decrease of velocity is observed close to the injection point and is surrounded by regions of increasing velocity. Our observations are consistent with hydromechanical measures. Below 15 Bars, we interpret the P-wave velocity increase to be related to the compression of the fault zone around the injection chamber. Above 15 Bars, we measure a shear and dilatant fault movement, and a rapid increase in the injected fluid flow. At this step, our measures are coherent with a poroelastic opening of the fault with velocities decrease at the injection source and velocities increase related to stress transfer in the far field. Velocity changes prove to be efficient to monitor stress/strain variation in an activated fault, even if these observations might produce complex signals due to the highly contrasted hydromechanical responses in a heterogeneous media such as a fault zone.

  9. Data Mining of the Thermal Performance of Cool-Pipes in Massive Concrete via In Situ Monitoring

    Directory of Open Access Journals (Sweden)

    Zheng Zuo

    2014-01-01

    Full Text Available Embedded cool-pipes are very important for massive concrete because their cooling effect can effectively avoid thermal cracks. In this study, a data mining approach to analyzing the thermal performance of cool-pipes via in situ monitoring is proposed. Delicate monitoring program is applied in a high arch dam project that provides a good and mass data source. The factors and relations related to the thermal performance of cool-pipes are obtained in a built theory thermal model. The supporting vector machine (SVM technology is applied to mine the data. The thermal performances of iron pipes and high-density polyethylene (HDPE pipes are compared. The data mining result shows that iron pipe has a better heat removal performance when flow rate is lower than 50 L/min. It has revealed that a turning flow rate exists for iron pipe which is 80 L/min. The prediction and classification results obtained from the data mining model agree well with the monitored data, which illustrates the validness of the approach.

  10. Kinetics of selenium release in mine waste from the Meade Peak Phosphatic Shale, Phosphoria Formation, Wooley Valley, Idaho, USA

    Science.gov (United States)

    Stillings, Lisa L.; Amacher, Michael C.

    2010-01-01

    Phosphorite from the Meade Peak Phosphatic Shale member of the Permian Phosphoria Formation has been mined in southeastern Idaho since 1906. Dumps of waste rock from mining operations contain high concentrations of Se which readily leach into nearby streams and wetlands. While the most common mineralogical residence of Se in the phosphatic shale is elemental Se, Se(0), Se is also an integral component of sulfide phases (pyrite, sphalerite and vaesite–pyritess) in the waste rock. It may also be present as adsorbed selenate and/or selenite, and FeSe2 and organo-selenides.Se release from the waste rock has been observed in field and laboratory experiments. Release rates calculated from waste rock dump and column leachate solutions describe the net, overall Se release from all of the possible sources of Se listed above. In field studies, Se concentration in seepage water (pH 7.4–7.8) from the Wooley Valley Unit 4 dump ranges from 3600 µg/L in May to 10 µg/L by Sept. Surface water flow, Q, from the seep also declines over the summer, from 2 L/s in May to 0.03 L/s in Sept. Se flux ([Se] ⁎ Q) reaches a steady-state of reaction with a rate constant, k, = 1.35 – 6.35e−3 h− 1 (11.8–55.6 yr− 1).Laboratory experiments were performed with the waste shale in packed bed reactors; residence time varied from 0.09 to 400 h and outlet pH ∼ 7.5. Here, Se concentration increased with increasing residence time and release was modeled with a first order reaction with k = 2.19e−3 h− 1 (19.2 yr− 1).Rate constants reported here fall within an order of magnitude of reported rate constants for oxidation of Se(0) formed by bacterial precipitation. This similarity among rate constants from both field and laboratory studies combined with the direct observation of Se(0) in waste shales of the Phosphoria Formation suggests that oxidation of Se(0) may control steady-state Se concentration in water draining the Wooley Valley waste dump.

  11. Engineering assessment and feasibility study of Chattanooga Shale as a future source of uranium. [Preliminary mining; data on soils, meteorology, water resources, and biological resources

    Energy Technology Data Exchange (ETDEWEB)

    1978-06-01

    This volume contains five appendixes: Chattanooga Shale preliminary mining study, soils data, meteorologic data, water resources data, and biological resource data. The area around DeKalb County in Tennessee is the most likely site for commercial development for recovery of uranium. (DLC)

  12. In-situ study of beneficial utilization of coal fly ash in reactive mine tailings.

    Science.gov (United States)

    Lee, Joon Kyu; Shang, Julie Q; Wang, Hongliu; Zhao, Cheng

    2014-03-15

    Oxidation of reactive mine tailings and subsequent generation of acid mine drainage (AMD) have been long recognized as the largest environmental concern for the mining industry. Laboratory studies on utilization of coal fly ash in management of reactive mine tailings have shown reducing water and oxygen infiltration into tailings matrix, thus preventing oxidation of sulphide minerals and acid generation. However, few data from field studies to evaluate the performance of co-placement of mine tailings and fly ash (CMF hereafter) are reported in the open literature. This paper documents the construction and instrumentation of three CMF systems on the Musselwhite mine located in Ontario, Canada and presents results of 3-year real time monitoring. The field data indicates that the CMFs reduced the ingress of water due to cementation generated by hydration of fly ash. It was also found that the electrical conductivity of leachate from CMFs decreased in the early stage of co-placement, compared to the control. With further study, the principle and approach demonstrated in this paper can be adopted as a sustainable technology in the mine tailings management. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Reliable cost effective technique for in situ ground stress measurements in deep gold mines.

    CSIR Research Space (South Africa)

    Stacey, TR

    1995-07-01

    Full Text Available measurement, and there are numerous methods of measurement which are currently in use. This report presents a literature survey of existing methods of in-situ stress measurement including an evaluation of the applicability of these methods in the deep level...

  14. In situ proteo-metabolomics reveals metabolite secretion by the acid mine drainage bio-indicator, Euglena mutabilis.

    Science.gov (United States)

    Halter, David; Goulhen-Chollet, Florence; Gallien, Sébastien; Casiot, Corinne; Hamelin, Jérôme; Gilard, Françoise; Heintz, Dimitri; Schaeffer, Christine; Carapito, Christine; Van Dorsselaer, Alain; Tcherkez, Guillaume; Arsène-Ploetze, Florence; Bertin, Philippe N

    2012-07-01

    Euglena mutabilis is a photosynthetic protist found in acidic aquatic environments such as peat bogs, volcanic lakes and acid mine drainages (AMDs). Through its photosynthetic metabolism, this protist is supposed to have an important role in primary production in such oligotrophic ecosystems. Nevertheless, the exact contribution of E. mutabilis in organic matter synthesis remains unclear and no evidence of metabolite secretion by this protist has been established so far. Here we combined in situ proteo-metabolomic approaches to determine the nature of the metabolites accumulated by this protist or potentially secreted into an AMD. Our results revealed that the secreted metabolites are represented by a large number of amino acids, polyamine compounds, urea and some sugars but no fatty acids, suggesting a selective organic matter contribution in this ecosystem. Such a production may have a crucial impact on the bacterial community present on the study site, as it has been suggested previously that prokaryotes transport and recycle in situ most of the metabolites secreted by E. mutabilis. Consequently, this protist may have an indirect but important role in AMD ecosystems but also in other ecological niches often described as nitrogen-limited.

  15. Modelling the Small Throw Fault Effect on the Stability of a Mining Roadway and Its Verification by In Situ Investigation

    Directory of Open Access Journals (Sweden)

    Małkowski Piotr

    2017-12-01

    Full Text Available The small throw fault zones cause serious problems for mining engineers. The knowledge about the range of fractured zone around the roadway and about roadway’s contour deformations helps a lot with the right support design or its reinforcement. The paper presents the results of numerical analysis of the effect of a small throw fault zone on the convergence of the mining roadway and the extent of the fracturing induced around the roadway. The computations were performed on a dozen physical models featuring various parameters of rock mass and support for the purpose to select the settings that reflects most suitably the behavior of tectonically disturbed and undisturbed rocks around the roadway. Finally, the results of the calculations were verified by comparing them with in situ convergence measurements carried out in the maingate D-2 in the “Borynia-Zofiówka-Jastrzębie” coal mine. Based on the results of measurements it may be concluded that the rock mass displacements around a roadway section within a fault zone during a year were four times in average greater than in the section tectonically unaffected. The results of numerical calculations show that extent of the yielding zone in the roof reaches two times the throw of the fault, in the floor 3 times the throw, and horizontally approx. 1.5 to 1.8 times the width of modelled fault zone. Only a few elasto-plastic models or models with joints between the rock beds can be recommended for predicting the performance of a roadway which is within a fault zone. It is possible, using these models, to design the roadway support of sufficient load bearing capacity at the tectonically disturbed section.

  16. Fire and explosion hazards of oil shale

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The US Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles. 10 refs., 54 figs., 29 tabs.

  17. 3D geomechanical modeling and numerical simulation of in-situ stress fields in shale reservoirs: A case study of the lower Cambrian Niutitang formation in the Cen'gong block, South China

    Science.gov (United States)

    Liu, Jingshou; Ding, Wenlong; Yang, Haimeng; Wang, Ruyue; Yin, Shuai; Li, Ang; Fu, Fuquan

    2017-08-01

    An analysis of the in-situ state of stress in a shale reservoir was performed based on comprehensive information about the subsurface properties from wellbores established during the development of an oil and gas field. Industrial-level shale gas production has occurred in the Niutitang formation of the lower Cambrian Cen'gong block, South China. In this study, data obtained from hydraulic fracturing, drilling-induced fractures, borehole breakout, global positioning system (GPS), and well deviation statistics have been used to determine the orientation of the maximum horizontal principal stress. Additionally, hydraulic fracturing and multi-pole array acoustic logging (XMAC) were used to determine the vertical variations in the in-situ stress magnitude. Based on logging interpretation and mechanical experiments, the spatial distributions of mechanical parameters were obtained by seismic inversion, and a 3D heterogeneous geomechanical model was established using a finite element stress analysis approach to simulate the in-situ stress fields. The effects of depth, faults, rock mechanics, and layer variations on the principal stresses, horizontal stress difference (Δσ), horizontal stress difference coefficient (Kh), and stress type coefficient (Sp) were determined. The results show that the direction of the maximum principal stress is ESE 120°. Additionally, the development zones of natural fractures appear to correlate with regions with high principal stress differences. At depths shallower than 375 m, the stress type is mainly a thrust faulting stress regime. At depths ranging from 375 to 950 m, the stress type is mainly a strike-slip faulting stress regime. When the depth is > 950 m, the stress type is mainly a normal faulting stress regime. Depth, fault orientation, and rock mechanics all affect the type of stress. The knowledge regarding the Cen'gong block is reliable and can improve borehole stability, casing set point determination, well deployment

  18. SSH gene expression profile of Eisenia andrei exposed in situ to a naturally contaminated soil from an abandoned uranium mine.

    Science.gov (United States)

    Lourenço, Joana; Pereira, Ruth; Gonçalves, Fernando; Mendo, Sónia

    2013-02-01

    The effects of the exposure of earthworms (Eisenia andrei) to contaminated soil from an abandoned uranium mine, were assessed through gene expression profile evaluation by Suppression Subtractive Hybridization (SSH). Organisms were exposed in situ for 56 days, in containers placed both in a contaminated and in a non-contaminated site (reference). Organisms were sampled after 14 and 56 days of exposure. Results showed that the main physiological functions affected by the exposure to metals and radionuclides were: metabolism, oxireductase activity, redox homeostasis and response to chemical stimulus and stress. The relative expression of NADH dehydrogenase subunit 1 and elongation factor 1 alpha was also affected, since the genes encoding these enzymes were significantly up and down-regulated, after 14 and 56 days of exposure, respectively. Also, an EST with homology for SET oncogene was found to be up-regulated. To the best of our knowledge, this is the first time that this gene was identified in earthworms and thus, further studies are required, to clarify its involvement in the toxicity of metals and radionuclides. Considering the results herein presented, gene expression profiling proved to be a very useful tool to detect earthworms underlying responses to metals and radionuclides exposure, pointing out for the detection and development of potential new biomarkers. Copyright © 2012 Elsevier Inc. All rights reserved.

  19. High‐stress triaxial direct‐shear fracturing of Utica shale and in situ X‐ray microtomography with permeability measurement

    National Research Council Canada - National Science Library

    Frash, Luke P; Carey, J. William; Lei, Zhou; Rougier, Esteban; Ickes, Timothy; Viswanathan, Hari S

    2016-01-01

    ...‐stress conditions remains underinvestigated at this time. The studies of this type that do exist do not include in situ fracture geometry measurements acquired at stressed conditions, which would be beneficial for interpreting the flow behavior...

  20. In situ bioassays with Chironomus riparius larvae to biomonitor metal pollution in rivers and to evaluate the efficiency of restoration measures in mine areas

    Energy Technology Data Exchange (ETDEWEB)

    Faria, Mafalda S. [CESAM and Departamento de Biologia da Universidade de Aveiro, Campus de Santiago, 3810-193 Aveiro (Portugal)], E-mail: mafaldafaria@sapo.pt; Lopes, Ricardo J. [CIBIO, Centro de Investigacao em Biodiversidade e Recursos Geneticos, Campus Agrario de Vairao, 4485-661 Vairao (Portugal); Malcato, Joao; Nogueira, Antonio J.A.; Soares, Amadeu M.V.M. [CESAM and Departamento de Biologia da Universidade de Aveiro, Campus de Santiago, 3810-193 Aveiro (Portugal)

    2008-01-15

    In this study we evaluate the ability of an in situ bioassay with Chironomus riparius larvae, using larval development and growth as endpoints, to biomonitor water quality and to assess the biological recovery of metal contaminated freshwater ecosystems of mine areas that are subject of restoration measures. The bioassay was carried out in streams located near an abandoned goldmine in North Portugal, throughout an environmental rehabilitation of the mine (2002-2004). During this period, a decrease in the inhibition of larval growth in the metal contaminated stream was observed. The bioassay was also performed in streams located near an active tungsten mine in Central Portugal. Larval growth and development were highly inhibited in the stream that receives acid drainage from the tungsten mine and treated water from the AMD treatment station. The results indicate that the bioassay can be used to evaluate the efficiency of environmental restoration measures in mining areas. - In situ bioassays with Chironomus riparius larvae can be a suitable tool to monitor restoration efficiency after a long time of metallic sediment contamination.

  1. In situ preservation and paleoenvironmental assessment of Taxodiacea fossil trees in the Buekkalja Lignite Formation, Buekkabrany open cast mine, Hungary

    Energy Technology Data Exchange (ETDEWEB)

    Hamor-Vido, Maria [Eoetvoes Lorand Geophysical Institute of Hungary, Kolumbusz st. 17-23 Budapest, H-1145 (Hungary); Hofmann, Tamas; Albert, Levente [Department of Chemistry, Faculty of Forestry, University of West Hungary, Ady Endre st. 5 Sopron, H-9400 (Hungary)

    2010-04-01

    In summer 2007 sixteen Taxodium tree trunks were found in situ standing position in the Buekkabrany open cast mine. The fossil trees were exposed during the excavation of the overburden layers of the Buekkalja Lignite Formation (BL). The Buekkabrany discovery is a global novum because the trees are very well preserved but not fossilized that makes the most detailed and direct analysis feasible. In spite of the 7-8 million years passed, the actual site and the host formation is rather intact, lacking tectonic deformations, deeper burial and/or dewatering during uplift. Organic petrology of tree trunks and sedimentology of the overburden sands are the subjects of this study. The extremely good preservation of fossil trunk tissues, presence of high amount of cellulose and moisture content along with the slightly gelified state of the wood and the lack of deformation indicate that there was only limited alteration during the early diagenesis. Chemical investigation of standing trunks fossil driftwood nearby the Late Miocene trees, and the fossil woods in the underlying lignite have revealed that their cellulose and total phenol concentrations were significantly lower than in intact recent trees, applied for reference. Yet their preservation levels were quite high, also proving that the chemical degradation of the fossil wood tissues had not been taken place extensively in the mire and the trees remained exceptionally well preserved. Sudden burial of the trees by strand plain sand beds indicates flooding by heavy storms or tsunamis, which interrupted and terminated the peat formation and preserved the trunks from later oxidation and biodegradation. (author)

  2. Wanted: rotary drilling technology for in situ mining systems. [Suggestions for imaginative use of technology and equipment

    Energy Technology Data Exchange (ETDEWEB)

    Laswell, G.W.

    1976-01-01

    It is pointed out that although available equipment and technology are not adequate for the varied requirements of the long-range in-situ recovery of our natural resources, effective programs can be accomplished now with innovative drill programs and equipment planning. The necessity of considering new and unusual techniques in order to ensure the success of an in-situ recovery program is emphasized. Three drilling concepts that are not being utilized but have in-situ applicability are discussed. They are underreaming, or chambering, dual-concentric drillpipe, and downhole tricone percussion. Various circulation media for use with in-situ drilling methods are discussed. (JGB)

  3. Mining nitrate concentration patterns from high-frequency in situ monitoring: a step towards more detailed understanding of hydrological processes?

    Science.gov (United States)

    Aubert, Alice; Houska, Tobias; Plesca, Ina; Kraft, Philipp; Breuer, Lutz

    2015-04-01

    Recently developed sensing technics allow collecting a considerable amount of high-frequency data; not only for hydrologic parameters (water levels, rainfall, etc.) but also for water chemistry. With devices such as in situ spectrophotometer, nitrate concentration can be monitored down to sub-hourly intervals. Thus, opening the way to new questions: what about daily or sub-daily instream nitrate concentration variations? What do these newly observed variations tell us about hydrological processes? In the Vollnkirchener Bach catchment, a headwater creek flows through a human impacted landscape dominated by agricultural and forest use and including a small settlement. Since March 2013, a Pro-PS device has been installed at the gauging station (monitored since 2011). Nitrate concentration is measured every 15 minutes, discharge and water temperature every 5 minutes. Data mining, more precisely motif discovery, is performed on these time series to identify high-resolution patterns. Spectral analysis highlighted that, in data measured at sub-hourly sampling frequency, variations up to a few hours are more likely to be dominated by measurement noise rather than real-world fluctuations. Therefore, we focus on daily motifs and flood patterns (given the fact that hydrological conditions are changing during flood events, we assume that nitrate concentration changes are depicting real processes). Various flood motifs were extracted: (1) nitrate can either be diluted or (2) concentrated, or (3) both (dilution followed by a bumpy recession curve indicating nitrate enrichment at the end of the flood). In addition to these classical nutrient-discharge behaviors, a variety of other interesting motifs were highlighted. (4) A daily nitrate cycle is clearly observed, but only during a specific year period. (5) Lag to peak time between parameters differentiate flood patterns: sometimes nitrate peaks first, sometimes discharge peaks first. (6) Furthermore, we are able to pinpoint the

  4. Phytoremediation Efficacy of Salix discolor and S. eriocephela on Adjacent Acidic Clay and Shale Overburden on a Former Mine Site: Growth, Soil, and Foliage Traits

    Directory of Open Access Journals (Sweden)

    Alex Mosseler

    2017-12-01

    Full Text Available Plants regularly experience suboptimal environments, but this can be particularly acute on highly-disturbed mine sites. Two North American willows—Salix discolor Muhl. (DIS and S. eriocephala Michx. (ERI—were established in common-garden field tests on two adjacent coal mine spoil sites: one with high clay content, the other with shale overburden. The high clay content site had 44% less productivity, a pH of 3.6, 42% clay content, high water holding capacity at saturation (64%, and high soil electrical conductivity (EC of 3.9 mS cm−1. The adjacent shale overburden site had a pH of 6.8, and after removing 56.5% stone content, a high sand content (67.2%, low water holding capacity at saturation (23%, and an EC of 0.9 mS cm−1. The acidic clay soil had significantly greater Na (20×, Ca (2×, Mg (4.4×, S (10×, C (12× and N (2× than the shale overburden. Foliar concentrations from the acidic clay site had significantly greater Mg (1.5×, Mn (3.3×, Fe (5.6×, Al (4.6×, and S (2× than the shale overburden, indicating that these elements are more soluble under acidic conditions. There was no overall species difference in growth; however, survival was greater for ERI than DIS on both sites, thus overall biomass yield was greater for ERI than DIS. Foliar concentrations of ERI were significantly greater than those of DIS for N (1.3×, Ca (1.5×, Mg (1.2×, Fe (2×, Al (1.5×, and S (1.5×. There were no significant negative relationships between metal concentrations and growth or biomass yield. Both willows showed large variation among genotypes within each species in foliar concentrations, and some clones of DIS and ERI had up to 16× the Fe and Al uptake on the acidic site versus the adjacent overburden. Genetic selection among species and genotypes may be useful for reclamation activities aimed at reducing specific metal concentrations on abandoned mine sites. Results show that, despite having a greater water holding capacity, the greater

  5. Assessment and control of water contamination associated with shale oil extraction and processing. Progress report, October 1, 1979-September 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, E.J.; Henicksman, A.V.; Fox, J.P.; O' Rourke, J.A.; Wagner, P.

    1982-04-01

    The Los Alamos National Laboratory's research on assessment and control of water contamination associated with oil shale operations is directed toward the identification of potential water contamination problems and the evaluation of alternative control strategies for controlling contaminants released into the surface and underground water systems from oil-shale-related sources. Laboratory assessment activities have focused on the mineralogy, trace element concentrations in solids, and leaching characteristics of raw and spent shales from field operations and laboratory-generated spent shales. This report details the chemical, mineralogic, and solution behavior of major, minor, and trace elements in a variety of shale materials (spent shales from Occidental retort 3E at Logan Wash, raw shale from the Colony mine, and laboratory heat-treated shales generated from Colony mine raw shale). Control technology research activities have focused on the definition of control technology requirements based on assessment activities and the laboratory evaluation of alternative control strategies for mitigation of identified problems. Based on results obtained with Logan Wash materials, it appears that the overall impact of in situ processing on groundwater quality (leaching and aquifer bridging) may be less significant than previously believed. Most elements leached from MIS spent shales are already elevated in most groundwaters. Analysis indicates that solubility controls by major cations and anions will aid in mitigating water quality impacts. The exceptions include the trace elements vanadium, lead, and selenium. With respect to in situ retort leaching, process control and multistaged counterflow leaching are evaluated as alternative control strategies for mitigation of quality impacts. The results of these analyses are presented in this report.

  6. Occidental vertical modified in situ process for the recovery of oil from oil shale. Phase II. Quarterly progress report, September 1, 1980-November 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    The major activities at OOSI's Logan Wash site during the quarter were: mining the voids at all levels for Retorts 7 and 8; blasthole drilling; tracer testing MR4; conducting the start-up and burner tests on MR3; continuing the surface facility construction; and conducting Retorts 7 and 8 related Rock Fragmentation tests. Environmental monitoring continued during the quarter, and the data and analyses are discussed. Sandia National Laboratory and Laramie Energy Technology Center (LETC) personnel were active in the DOE support of the MR3 burner and start-up tests. In the last section of this report the final oil inventory for Retort 6 production is detailed. The total oil produced by Retort 6 was 55,696 barrels.

  7. Evaluation in situ of genotoxicity and stress in South American common toad Rhinella arenarum in environments related to fluorite mine.

    Science.gov (United States)

    Pollo, Favio E; Grenat, Pablo R; Salinas, Zulma A; Otero, Manuel A; Salas, Nancy E; Martino, Adolfo L

    2017-08-01

    Little attention has been paid to the impact of wastewater generated by mining activities on fluoride. In this study, we evaluated the hematology responses of common South American toad Rhinella arenarum inhabiting natural and artificial environments associated with a fluorite mine from central Argentina. We analyzed three sampling stations associated with the fluorite mine: (I) Los Cerros Negros stream (CN), which runs on granitic rock with a high fluorite content; (II) Los Vallecitos stream (LV), which runs on metamorphic rock with low fluorite content; and (III) artificial decantation ponds (DP) containing sediments produced by fluorite flotation process. We calculated frequencies of micronuclei, erythrocyte nuclear abnormalities, mitosis, and immature erythrocytes. In addition, we performed a differential leukocyte count and determined neutrophils/lymphocyte ratio as a stress response estimator. We found high micronucleus (MN) and erythrocyte nuclear abnormality (ENA) frequencies in DP and CN but low frequencies in LV. The neutrophil/lymphocyte ratio was different among sites, with a significant increase in individuals from DP. Values registered in DP could be caused by exposure to mixture of compounds registered in dams that hold wastewater, while high values registered in CN stream might be due to natural concentrations of fluoride. Our results suggest that blood is an effective and non-destructive sensitive indicator for monitoring genotoxic agents in freshwater ecosystems.

  8. Determination of the Metabolic Rate and Work Arduousness Class for Workers in Coal Mines - The Results of in Situ Research

    Science.gov (United States)

    Drenda, Jan; Kułagowska, Ewa; Różański, Zenon; Pach, Grzegorz; Wrona, Paweł; Karolak, Izabela

    2017-06-01

    Considering different duties and activities among miners working in underground coal mines, their work is connected with variable metabolic rate. Determination of this rate for different workplace was the aim of the research and was the base for set up the work arduousness classes for the workplace (according to the standard PN-EN 27243). The research covered 6 coal mines, 268 workers and 1164 series of measurements. Metabolic rate was established on the base of heart rate obtained from individual pulsometers (according to the standard PN-EN ISO 8996). Measurements were supplemented by poll surveys about worker and thermal environment parameters. The results showed significant variability of average heart rate (from 87 bmp to 100 bpm) with variance coefficient 14%. Mean values of metabolic rate were from 150 W/m2 to 207 W/m2. According to the results, the most common class of work arduousness was at moderate metabolic rate (class 2 - moderate work), however, more intense work was found in headings, especially at " blind end" workplace.

  9. In Situ Generated Colloid Transport of Cu and Zn in Reclaimed Mine Soil Profiles Associated with Biosolids Application

    Directory of Open Access Journals (Sweden)

    Jarrod O. Miller

    2011-01-01

    Full Text Available Areas reclaimed for agricultural uses following coal mining often receive biosolids applications to increase organic matter and fertility. Transport of heavy metals within these soils may be enhanced by the additional presence of biosolids colloids. Intact monoliths from reclaimed and undisturbed soils in Virginia and Kentucky were leached to observe Cu and Zn mobility with and without biosolids application. Transport of Cu and Zn was observed in both solution and colloid associated phases in reclaimed and undisturbed forest soils, where the presence of unweathered spoil material and biosolids amendments contributed to higher metal release in solution fractions. Up to 81% of mobile Cu was associated with the colloid fraction, particularly when gibbsite was present, while only up to 18% of mobile Zn was associated with the colloid fraction. The colloid bound Cu was exchangeable by ammonium acetate, suggesting that it will release into groundwater resources.

  10. In-situ electrochemical measurements of total concentration and speciation of heavy metals in acid mine drainage (AMD): assessment of the use of anodic stripping voltammetry.

    Science.gov (United States)

    Jung, Hun-Bok; Yun, Seong-Taek; Kim, Soon-Oh; Jung, Myung Chae; So, Chil-Sup; Koh, Yong-Kwon

    2006-06-01

    We assessed the use of anodic stripping voltammetry (ASV) for in-situ determinations of both total concentration and speciation of dissolved heavy metals (Cd, Cu, Pb and Zn) in acid mine drainage (AMD). In the Kwangyang Au-Ag mine area of South Korea, different sites with varying water chemistry within an AMD were studied with a field portable anodic stripping voltammeter. Anodic stripping voltammetry after wet oxidation (acidification) was very sensitive enough to determine total concentration of dissolved Cd because Cd was dominantly present as 'labile' species, whilst the technique was not so effective for determining total Cu especially in the downstream sites from the retention pond, due to its complexation with organic matter. For dissolved Pb, the concentrations determined by ASV after wet oxidation generally agreed with those by ICP-AES. In the downstream samples (pH>5), however, ASV data after wet oxidation were lower than ICP-AES data because a significant fraction of dissolved Pb was present in those samples as 'inert' species associated with colloidal iron oxide particles. The determination of total dissolved Zn by ASV after wet oxidation appeared to be unsatisfactory for the samples with high Cu content, possibly due to the interference by the formation of Zn-Cu intermetallic compounds on the mercury coated electrode. In AMD samples with high dissolved iron, use of ultraviolet irradiation was not effective for determining total concentrations because humate destruction by UV irradiation possibly resulted in the removal of a part of dissolved heavy metals from waters through the precipitation of iron hydroxides.

  11. Assessment in situ of genotoxicity in tadpoles and adults of frog Hypsiboas cordobae (Barrio 1965) inhabiting aquatic ecosystems associated to fluorite mine.

    Science.gov (United States)

    Pollo, Favio E; Grenat, Pablo R; Otero, Manuel A; Salas, Nancy E; Martino, Adolfo L

    2016-11-01

    Non-lethal biological techniques such as blood biomarkers have gained attention due to their value as early signals of anthropic effects of contamination representing significant tools to evaluate ecosystems health. We evaluate and characterize in situ genotoxicity of water samples collected from aquatic ecosystems around a fluorite mine using amphibian frogs Hypsiboas cordobae as bioindicator species complemented with 16 physicochemical parameters. Four stations associated with fluorite mine sampling were sampled: a stream running on granitic rock with natural high fluorite content; two streams both running on metamorphic rock with low fluorite content; and an artificial decantation pond containing sediments produced by fluorite flotation process with high variation in physicochemical parameters. We analyses the blood of tadpoles and adults of H. Cordobae, calculated frequencies of micronuclei, erythrocyte nuclear abnormalities, mitosis, immature and enucleated erythrocytes. Individuals were measured and weighed and body condition was calculated. The results of this study indicate that individuals of decantation pond are exposed to compounds or mixtures which are causing cell damage when compared to those that were collected of stream. Larval stage was more vulnerable than the adult phase and it could be related mainly to the higher exposure time to xenobiotics, which can penetrate easily by skin, mouth and gills; additionally this site offers a reduced availability of food than other sites. Therefore, chronic exposure to pollutants could derive in degenerative and neoplastic diseases in target organs. Moreover these individuals may experience reproductive and behavioral disturbances which could lead to population decline in the long term. Copyright © 2016 Elsevier Inc. All rights reserved.

  12. Denitrification in marine shales in northeastern Colorado

    Science.gov (United States)

    McMahon, P.B.; Böhlke, J.K.; Bruce, B.W.

    1999-01-01

    Parts of the South Platte River alluvial aquifer in northeastern Colorado are underlain by the Pierre Shale, a marine deposit of Late Cretaceous age that is electron donors for denitrification in the forms of organic carbon and sulfide minerals. Nested piezometers were sampled, pore water was squeezed from cores of shale, and an injection test was conducted to determine if denitrification in the shale was a sink for alluvial NO3/- and to measure denitrification rates in the shale. Measured values of NO3/-, N2, NH4/+, ??15[NO3/-], ??15N[N2], and ??15N[NH4/+] in the alluvial and shale pore water indicated that denitrification in the shale was a sink for alluvial NO3/-. Chemical gradients, reaction rate constants, and hydraulic head data indicated that denitrification in the shale was limited by the slow rate of NO3/- transport (possibly by diffusion) into the shale. The apparent in situ first-order rate constant for denitrification in the shale based on diffusion calculations was of the order of 0.04-0.4 yr-1, whereas the potential rate constant in the shale based on injection tests was of the order of 60 yr-1. Chemical data and mass balance calculations indicate that organic carbon was the primary electron donor for denitrification in the shale during the injection test, and ferrous iron was a minor electron donor in the process. Flux calculations for the conditions encountered at the site indicate that denitrification in the shale could remove only a small fraction of the annual agricultural NO3/- input to the alluvial aquifer. However, the relatively large potential first-order rate constant for denitrification in the shale indicated that the percentage of NO3/- uptake by the shale could be considerably larger in areas where NO3/- is transported more rapidly into the shale by advection.

  13. Oil Shale

    Science.gov (United States)

    Birdwell, Justin E.

    2017-01-01

    Oil shales are fine-grained sedimentary rocks formed in many different depositional environments (terrestrial, lacustrine, marine) containing large quantities of thermally immature organic matter in the forms of kerogen and bitumen. If defined from an economic standpoint, a rock containing a sufficient concentration of oil-prone kerogen to generate economic quantities of synthetic crude oil upon heating to high temperatures (350–600 °C) in the absence of oxygen (pyrolysis) can be considered an oil shale.

  14. Western oil-shale development: a technology assessment. Volume 6: oil-shale development in the Piceance Creek Basin and potential water-quality changes

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    This report brackets the stream quality changes due to pre-mining pumping activites required to prepare oil shale lease Tracts C-a and C-b for modified in situ retorting. The fluxes in groundwater discharged to the surface were identified for Tract C-b in a modeling effort by another laboratory. Assumed fluxes were used for Tract C-a. The quality of the groundwater aquifers of the Piceance Basin is assumed to be that reported in the literature. The changes are bracketed in this study by assuming all premining pumping is discharged to the surface stream. In one case, the pumped water is assumed to be of a quality like that of the upper aquifer with a relatively high quality. In the second case, the pumped water is assumed to come from the lower aquifer. Complete mixing and conservation of pollutants was assumed at sample points at the White River and at Lees Ferry of the Colorado River. A discussion of possible secondary effects of oil shale and coal mining is presented. In addition, a discussion of the uncertainties associated with the assumptions used in this study and alternative uses for the water to prevent stream contamination by oil shale development is provided.

  15. 77 FR 5566 - Notice of Availability of the Final EIS for the HB In-Situ Solution Mine Project, Eddy County...

    Science.gov (United States)

    2012-02-03

    ...., Carlsbad, New Mexico 88220. Interested persons may also review the Final EIS on the Internet at http://www... method. Intrepid proposes to ] construct and operate a solution mine project in an existing deep mine...

  16. Insights into induced earthquakes and aftershock activity with in-situ measurements of seismic velocity variations in an active underground mine

    Science.gov (United States)

    Brenguier, F.; Olivier, G.; Campillo, M.; Roux, P.; Shapiro, N.; Lynch, R.

    2015-12-01

    The behaviour of the crust shortly after large earthquakes has been the subject of numerous studies, but many co- and post-seismic processes remain poorly understood. Damage and healing of the bulk rock mass, post-seismic deformation and the mechanisms of earthquake triggering are still not well understood. These processes are important to properly model and understand the behaviour of faults and earthquake cycles.In this presentation, we will show how in-situ measurements of seismic velocity variations have given new insights into these co- and post-seismic processes. An experiment was performed where a blast was detonated in a tunnel in an underground mine, while seismic velocity variations were accurately (0.005 %) measured with ambient seismic noise correlations. Additionally, aftershock activity was examined and the influence of the removal of a piece of solid rock was estimated with elastic static stress modelling. The majority of the aftershocks were delayed with respect to the passing of the dynamic waves from the blast, while the locations of the aftershocks appeared clustered and not homogeneously spread around the blast location. A significant velocity drop is visible during the time of the blast, which is interpreted as co-seismic damage and plastic deformation. These non-elastic effects are healed by the confining stresses over a period of 5 days until the seismic velocity converges to a new baseline level. The instantaneous weakening and gradual healing observed from the velocity variations are qualitatively similar to results reported in laboratory studies. The change in the baseline level of the seismic velocity before and after the blast indicate a change in the static stress that is comparable to the results of elastic static stress modelling. The differences between the elastic model predictions and the seismic velocity variations could be due to zones of fractured rock, indicated by the spatial clustering of the aftershocks, that are not

  17. Spectroscopic study on biological mackinawite (FeS) synthesized by ferric reducing bacteria (FRB) and sulfate reducing bacteria (SRB): Implications for in-situ remediation of acid mine drainage

    Science.gov (United States)

    Zhou, Lei; Liu, Jing; Dong, Faqin

    2017-02-01

    Mackinawite (FeS), widespread in low temperature aquatic environments, is generally considered to be the first Fe sulfide formed in sedimentary environments which has shown effective immobilization of heavy metals and toxic oxyanions through various sorption reactions. The spectroscopic study researches on mackinawite formed by FRB and SRB and its environmental implication for in-situ remediation of acid mine drainage where contains large amounts of Fe3 + and SO42 -. The XRD result of biologically synthetic particles shows that these particles are mainly composed of mackinawite (FeS0.9). The Raman peaks observed at 208, 256, 282, 298 cm- 1 are attributed to Fesbnd S stretching vibrations of mackinawite. The Attenuated Total Reflection-Fourier Transform Infrared Spectroscopy (ATR-FTIR) reveals that the diagnostic bands of low intensity for these FeS particles occur at 412-425 cm- 1 and 607-622 cm- 1, which are assigned to the stretching vibrations of Ssbnd S and Fesbnd S bonds. The Raman and IR vibrations from organic components both confirm that these particles are biogenic origin. The IR spectra of biologically synthesized mackinawite for different aging times show that the nano-sized particles mackinwate will be completely oxidized within 10 h. All these findings have good implications for in-situ remediation of acid mine drainage.

  18. Mining

    Directory of Open Access Journals (Sweden)

    Khairullah Khan

    2014-09-01

    Full Text Available Opinion mining is an interesting area of research because of its applications in various fields. Collecting opinions of people about products and about social and political events and problems through the Web is becoming increasingly popular every day. The opinions of users are helpful for the public and for stakeholders when making certain decisions. Opinion mining is a way to retrieve information through search engines, Web blogs and social networks. Because of the huge number of reviews in the form of unstructured text, it is impossible to summarize the information manually. Accordingly, efficient computational methods are needed for mining and summarizing the reviews from corpuses and Web documents. This study presents a systematic literature survey regarding the computational techniques, models and algorithms for mining opinion components from unstructured reviews.

  19. In-situ remediation strategy for enhanced microbial de-acidification of geogenic sulphuric acid mining lakes - mesocosmic studies; In situ-Sanierungsstrategie zur Foerderung der mikrobiellen Entsaeuerung von geogen schwefelsauren Bergbaurestseen - Mesokosmosstudien

    Energy Technology Data Exchange (ETDEWEB)

    Froemmichen, R.

    2001-07-01

    The author investigated whether neutralisation of acid mining lakes can be enhanced by adding low-cost, complex organic carbon sources. Subjects: Selection of a complex carbon source suited for stimulation of dissimilatory iron and sulfate reduction; design and observation of a near-natural landscape compartment (mesocosmos) at different scales as a preparation for the field study; Description of reactions in the mesocosmic lake water and sediment; Assessment of neutralisation equivalents and neutralisation rates on the basis of an identification of reduced iron and sulphur compounds. [German] Die Hypothese, dass durch Zugabe kostenguenstiger komplexer organischer Kohlenstoffquellen in die sedimentnahe Wasserzone eines sauren Tagebaurestsees seeinterne Neutralisierungsprozesse gefoerdert werden, liegt dieser Arbeit zu Grunde. Seeinterne Neutralisationsprozesse, wie die dissimilatorische Eisen- und Sulfatreduktion, fuehren ueber die Akkumulierung von reduzierten Eisen- und Schwefelverbindungen im Sediment zur Alkalinitaetsbildung im Gewaessersystem und im Seewasser zu hoeheren pH-Werten. Daher leiten sich folgende Ziele fuer diese Arbeit ab: - Auswahl einer geeigneten komplexen Kohlenstoffquelle zur Stimulierung der dissimilatorischen Eisen- und Sulfatreduktion - Design und Beobachtung eines naturnahen Landschaftsausschnittes (Mesokosmos) unterschiedlicher Massstabsebenen in Vorbereitung fuer die Fallstudie im Freiland - Beschreibung von Stoffumsetzungen im Seewasser und -sediment der Mesokosmen - Abschaetzung von Neutralisationsaequivalenten und Bestimmung von Neutralisationsraten anhand der Identifizierung reduzierter Eisen- und Schwefelverbindungen. (orig.)

  20. Thermomechanical properties of selected shales

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, F.D.; Vogt, T.J.

    1987-08-01

    The experimental work discussed in this report is part of an ongoing program concerning evaluation of sedimentary and other rock types as potential hosts for a geologic repository. The objectives are the development of tools and techniques for repository characterization and performance assessment in a diversity of geohydrologic settings. This phase of the program is a laboratory study that investigates fundamental thermomechanical properties of several different shales. Laboratory experiments are intrinsically related to numerical modeling and in situ field experiments, which together will be used for performance assessment.

  1. In situ

    Science.gov (United States)

    Chamlagain, Bhawani; Sugito, Tessa A; Deptula, Paulina; Edelmann, Minnamari; Kariluoto, Susanna; Varmanen, Pekka; Piironen, Vieno

    2018-01-01

    The in situ production of active vitamin B12 was investigated in aqueous cereal-based matrices with three strains of food-grade Propionibacterium freudenreichii . Matrices prepared from malted barley flour (33% w/v; BM), barley flour (6%; BF), and wheat aleurone (15%; AM) were fermented. The effect of cobalt and the lower ligand 5,6-dimethylbenzimidazole (DMBI) or its natural precursors (riboflavin and nicotinamide) on active B12 production was evaluated. Active B12 production was confirmed by UHPLC-UV-MS analysis. A B12 content of 12-37 μg·kg -1 was produced in BM; this content increased 10-fold with cobalt and reached 940-1,480 μg·kg -1 with both cobalt and DMBI. With riboflavin and nicotinamide, B12 production in cobalt-supplemented BM increased to 712 μg·kg -1 . Approximately, 10 μg·kg -1 was achieved in BF and AM and was increased to 80 μg·kg -1 in BF and 260 μg·kg -1 in AM with cobalt and DMBI. The UHPLC and microbiological assay (MBA) results agreed when both cobalt and DMBI or riboflavin and nicotinamide were supplemented. However, MBA gave ca. 20%-40% higher results in BM and AM supplemented with cobalt, indicating the presence of human inactive analogues, such as pseudovitamin B12. This study demonstrates that cereal products can be naturally fortified with active B12 to a nutritionally relevant level by fermenting with P. freudenreichii .

  2. Assessing the responses of creek chub (Semotilus atromaculatus) and pearl dace (Semotilus margarita) to metal mine effluents using in situ artificial streams in Sudbury, Ontario, Canada.

    Science.gov (United States)

    Dubé, Monique G; MacLatchy, Deborah L; Hruska, Kimberly A; Glozier, Nancy E

    2006-01-01

    Mining of the world's second-largest nickel deposits in the area of Sudbury, Ontario, Canada, has caused acidification and metal saturation of some catchments. We conducted artificial stream studies in the years 2001 and 2002 to assess the effects of treated metal mine effluents (MMEs) from three different mining operations discharging to Junction Creek, Sudbury, on two fish species, creek chub (Semotilus atromaculatus) and pearl dace (Semotilus margarita). Treatments tested for 35 to 41 d included reference water, Garson MME (30%), Nolin MME (20%), and Copper Cliff MME (45%). In 2001, effects on chub included reduced survival and depressed testosterone levels (fivefold reduction) after exposure to all MMEs. In 2002, chub and dace survival were reduced to less than 60% in the Copper Cliff and Garson treatments. In addition, the total body weights of male and female dace were reduced after exposure to the Garson and Copper Cliff treatments. In 2001 and 2002, responses were most common to the 45% Copper Cliff and 30% Garson effluents, with consistent increases in nickel, rubidium, strontium, iron, lithium, thallium, and selenium observed across treatment waters and body tissues. More work is required to link observed effects to field effects and to identify multitrophic level responses of the ecosystem to the MMEs. The artificial stream studies provided a mechanism to identify changes in the endpoints of relevant fish species exposed to present-day metal mine discharges independent of historical depositions of metals in the Sudbury area.

  3. The Shale Gas in Europe project (GASH)

    Science.gov (United States)

    Schulz, Hans-Martin; Horsfield, Brian; Gash-Team

    2010-05-01

    At the present time no shale gas play has been brought to the production level in Europe. While the opportunities appear abundant, there are still many challenges to be overcome in Europe such as land access and environmental issues. Costs per well are still higher than in the US, and mining regulations are tighter. As yet it remains unclear whether European shales can support commercial shale gas production. First, it will be essential to test the sub-surface and the potential deliverability of wells, supported by basic research. GASH is the first major scientific initiative in Europe that is focussed on shale gas; it is ambitious in that it is broad ranging in scientific scope and that it unites leading European research groups and geological surveys with industry. US know-how is also integrated into the programme to avoid reinventing the wheel, or, still worse, the flat tyre. GASH is currently funded by eight companies, and comprises two main elements: compilation of a European Black Shale Database (EBSD) and focussed research projects that are based on geochemical, geophysical and geomechanical investigations. The EBSD is being built by a team of more than 20 geological surveys, extending from Sweden in the north, through western Europe and the Baltic states down to southern Europe, and over to Romania, Hungary and the Czech Republic in the east. The research projects apply numerical modelling, process simulations and laboratory analyses to selected regional study areas or "natural laboratories" from both Europe and the USA - the goal: to predict gas-in-place and fracability based on process understanding. The European black shales selected as natural shale gas laboratories are the Cambrian Alum Shale from Sweden and Denmark, the Lower Jurassic Posidonia Shale from Central Germany, and Carboniferous black shales from the UK in the west via the Netherlands to Germany in the east. Fresh core material for detailed investigations will be recovered during the mid

  4. The Devonian Marcellus Shale and Millboro Shale

    Science.gov (United States)

    Soeder, Daniel J.; Enomoto, Catherine B.; Chermak, John A.

    2014-01-01

    The recent development of unconventional oil and natural gas resources in the United States builds upon many decades of research, which included resource assessment and the development of well completion and extraction technology. The Eastern Gas Shales Project, funded by the U.S. Department of Energy in the 1980s, investigated the gas potential of organic-rich, Devonian black shales in the Appalachian, Michigan, and Illinois basins. One of these eastern shales is the Middle Devonian Marcellus Shale, which has been extensively developed for natural gas and natural gas liquids since 2007. The Marcellus is one of the basal units in a thick Devonian shale sedimentary sequence in the Appalachian basin. The Marcellus rests on the Onondaga Limestone throughout most of the basin, or on the time-equivalent Needmore Shale in the southeastern parts of the basin. Another basal unit, the Huntersville Chert, underlies the Marcellus in the southern part of the basin. The Devonian section is compressed to the south, and the Marcellus Shale, along with several overlying units, grades into the age-equivalent Millboro Shale in Virginia. The Marcellus-Millboro interval is far from a uniform slab of black rock. This field trip will examine a number of natural and engineered exposures in the vicinity of the West Virginia–Virginia state line, where participants will have the opportunity to view a variety of sedimentary facies within the shale itself, sedimentary structures, tectonic structures, fossils, overlying and underlying formations, volcaniclastic ash beds, and to view a basaltic intrusion.

  5. In-situ bioremediation of contaminated soils from Rodna mining areas from Bistrița-Năsăud county

    Directory of Open Access Journals (Sweden)

    Cornel Negrusier

    2016-11-01

    Full Text Available Soil ecosystems contaminated with heavy metals can cause significant damages to the environment and human health due to the mobility and solubility capacity of the contaminants. This research was carried out to set up a suitable bioremediation scheme for cleaning up the soil from the mining sites of Anieș and Glod Valley from Bistrița-Năsăud county. Based on the investigations that have been made (soil colour, pH, organic content of the soil, plant inventory phytoremediation seemed to be the most effective and environmentally-friendly method that could be used to neutralize or remove heavy metals from the soil.

  6. Quantifying porosity, compressibility and permeability in Shale

    DEFF Research Database (Denmark)

    Mbia, Ernest Ncha; Fabricius, Ida Lykke; Frykman, Peter

    The Fjerritslev Formation in the Norwegian-Danish Basin forms the main seal to Upper Triassic-Lower Jurassic sandstone reservoirs. In order to estimate rock properties Jurassic shale samples from deep onshore wells in Danish basin were studied. Mineralogical analysis based on X-ray diffractometry...... (XRD) of shale samples show about 50% silt and high content of kaolinite in the clay fraction when compared with offshore samples from the Central Graben. Porosity measurements from helium porosimetry-mercury immersion (HPMI), mercury injection capillary pressure (MICP) and nuclear magnetic resonance...... (NMR) show that, the MICP porosity is 9-10% points lower than HPMI and NMR porosity. Compressibility result shows that deep shale is stiffer in situ than normally assumed in geotechnical modelling and that static compressibility corresponds with dynamic one only at the begining of unloading stress...

  7. Performance of a field-scale permeable reactive barrier based on organic substrate and zero-valent iron for in situ remediation of acid mine drainage.

    Science.gov (United States)

    Gibert, Oriol; Cortina, José Luis; de Pablo, Joan; Ayora, Carlos

    2013-11-01

    A permeable reactive barrier (PRB) was installed in Aznalcóllar (Spain) in order to rehabilitate the Agrio aquifer groundwater severely contaminated with acid mine drainage after a serious mining accident. The filling material of the PRB consisted of a mixture of calcite, vegetal compost and, locally, Fe(0) and sewage sludge. Among the successes of the PRB are the continuous neutralisation of pH and the removal of metals from groundwater within the PRB (removals of >95%). Among the shortcomings are the improper PRB design due to the complexity of the internal structure of the Agrio alluvial deposits (which resulted in an inefficient capture of the contaminated plume), the poor degradability of the compost used and the short residence time within the PRB (which hindered a complete sulphate reduction), the clogging of a section of the PRB and the heterogeneities of the filling material (which resulted in preferential flows within the PRB). Undoubtedly, it is only through accumulated experience at field-scale systems that the potentials and limits of the PRB technology can be determined.

  8. Western Greece unconventional hydrocarbon potential from oil shale and shale gas reservoirs

    Science.gov (United States)

    Karakitsios, Vasileios; Agiadi, Konstantina

    2013-04-01

    It is clear that we are gradually running out of new sedimentary basins to explore for conventional oil and gas and that the reserves of conventional oil, which can be produced cheaply, are limited. This is the reason why several major oil companies invest in what are often called unconventional hydrocarbons: mainly oil shales, heavy oil, tar sand and shale gas. In western Greece exist important oil and gas shale reservoirs which must be added to its hydrocarbon potential1,2. Regarding oil shales, Western Greece presents significant underground immature, or close to the early maturation stage, source rocks with black shale composition. These source rock oils may be produced by applying an in-situ conversion process (ICP). A modern technology, yet unproven at a commercial scale, is the thermally conductive in-situ conversion technology, developed by Shell3. Since most of western Greece source rocks are black shales with high organic content, those, which are immature or close to the maturity limit have sufficient thickness and are located below 1500 meters depth, may be converted artificially by in situ pyrolysis. In western Greece, there are several extensive areas with these characteristics, which may be subject of exploitation in the future2. Shale gas reservoirs in Western Greece are quite possibly present in all areas where shales occur below the ground-water level, with significant extent and organic matter content greater than 1%, and during their geological history, were found under conditions corresponding to the gas window (generally at depths over 5,000 to 6,000m). Western Greece contains argillaceous source rocks, found within the gas window, from which shale gas may be produced and consequently these rocks represent exploitable shale gas reservoirs. Considering the inevitable increase in crude oil prices, it is expected that at some point soon Western Greece shales will most probably be targeted. Exploration for conventional petroleum reservoirs

  9. Validation Results for Core-Scale Oil Shale Pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Staten, Josh; Tiwari, Pankaj

    2015-03-01

    This report summarizes a study of oil shale pyrolysis at various scales and the subsequent development a model for in situ production of oil from oil shale. Oil shale from the Mahogany zone of the Green River formation was used in all experiments. Pyrolysis experiments were conducted at four scales, powdered samples (100 mesh) and core samples of 0.75”, 1” and 2.5” diameters. The batch, semibatch and continuous flow pyrolysis experiments were designed to study the effect of temperature (300°C to 500°C), heating rate (1°C/min to 10°C/min), pressure (ambient and 500 psig) and size of the sample on product formation. Comprehensive analyses were performed on reactants and products - liquid, gas and spent shale. These experimental studies were designed to understand the relevant coupled phenomena (reaction kinetics, heat transfer, mass transfer, thermodynamics) at multiple scales. A model for oil shale pyrolysis was developed in the COMSOL multiphysics platform. A general kinetic model was integrated with important physical and chemical phenomena that occur during pyrolysis. The secondary reactions of coking and cracking in the product phase were addressed. The multiscale experimental data generated and the models developed provide an understanding of the simultaneous effects of chemical kinetics, and heat and mass transfer on oil quality and yield. The comprehensive data collected in this study will help advance the move to large-scale in situ oil production from the pyrolysis of oil shale.

  10. Current status of the production of chemicals from oil shale

    Energy Technology Data Exchange (ETDEWEB)

    Yesavage, V.F.; Griswold, C.F.; Dickson, P.F.

    1980-08-01

    An alternate use of shale oil is as a feedstock for chemical intermediates (ethylene, propylene, benzene, toluene, and xylene (BTX)) production. The most extensively used method for production of petrochemical intermediates is by steam pyrolysis of a hydrocarbon feed. Steam pyrolysis is generally directed towards maximizing ethylene production while producing other olefins and aromatics as salable by-products. Crude shale oil has a high content of organic nitrogen (2% by weight), which acts as a catalyst poison, contains a large residuum fraction (20 to 50% by weight) and has a high pour point (generally > 40/sup 0/). Thus, it has generally been considered necessary to prerefine crude shale oil to produce a synthetic crude compatible with typical refineries. The prerefinery steps generally consist either of a delayed coking step on the crude shale oil or residuum fraction, followed by one or several hydrogenation steps, or of direct hydrogenation of crude shale oil at more severe conditions. These hydrogenation steps must generally be accomplished under severe operating conditions (750/sup 0/F, 2000 psia hydrogen partial pressure and up to 2000 Scf/bbl hydrogen uptake). Since such severe prerefining of crude shale oil may not be required for the utilization of shale oil as a steam pyrolysis feedstock, use of shale oil as a petrochemical feedstock offers a potential advantage over usage for a refinery feedstock. Studies made by the US Bureau of Mines, the Institute of Gas Technology, and the Colorado School of Mines on the conversion of shale oil to petrochemicals are summarized. A comparison is made between shale oil and petroleum oil pyrolysis. (DMC)

  11. Properties of Silurian shales from the Barrandian Basin, Czech Republic

    Science.gov (United States)

    Weishauptová, Zuzana; Přibyl, Oldřich; Sýkorová, Ivana

    2017-04-01

    Although shale gas-bearing deposits have a markedly lower gas content than coal deposits, great attention has recently been paid to shale gas as a new potential source of fossil energy. Shale gas extraction is considered to be quite economical, despite the lower sorption capacity of shales, which is only about 10% of coal sorption capacities The selection of a suitable locality for extracting shale gas requires the sorption capacity of the shale to be determined. The sorption capacity is determined in the laboratory by measuring the amount of methane absorbed in a shale specimen at a pressure and a temperature corresponding to in situ conditions, using high pressure sorption. According to the principles of reversibility of adsorption/desorption, this amount should be roughly related to the amount of gas released by forced degassing. High pressure methane sorption isotherms were measured on seven representative samples of Silurian shales from the Barrandian Basin, Czech Republic. Excess sorption measurements were performed at a temperature of 45oC and at pressures up to 15 MPa on dry samples, using a manometric method. Experimental methane high-pressure isotherms were fitted to a modified Langmuir equation. The maximum measured excess sorption parameter and the Langmuir sorption capacity parameter were used to study the effect of TOC content, organic maturity, inorganic components and porosity on the methane sorption capacity. The studied shale samples with random reflectance of graptolite 0.56 to 1.76% had a very low TOC content and dominant mineral fractions. Illite was the prevailing clay mineral. The sample porosity ranged from 4.6 to 18.8%. In most samples, the micropore volumes were markedly lower than the meso- and macropore volumes. In the Silurian black shales, the occurrence of fractures parallel with the original sedimentary bending was highly significant. A greater proportion of fragments of carbonaceous particles of graptolites and bitumens in the

  12. Utilization of shale oil as a feedstock for steam pyrolysis and petrochemical intermediate production. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Dickson, P.F.; Yesavage, V.F.

    1979-09-01

    The major objectives of this study were to determine the effects of prerefining on product yields for steam pyrolysis of a shale oil feed and to determine the suitability of shale oil as a petrochemical feedstock. The results of this research program have in general been highly successful. A bench scale pyrolysis reactor was designed and constructed which was used to obtain yield data for variable operating conditions in the range typically employed commercially. Two crude shale oils were used in this study, a Tosco II shale oil as an example of above ground retorting and simulated in-situ shale oil as an example of in-situ processing. Each crude oil was processed to four different levels of prerefining: vacuum distillation and hydrogenation of the vacuum distillate at three levels of severity. A total of 112 experimental runs have been performed on the 10 shale oil samples. An initial comparison of shale oil with petroleum feedstocks indicates that yields of all major gaseous components for shale oil feedstocks are comparable with yields for petroleum fractions with the exception of ethylene. Yields of ethylene are in general considerably higher for the shale oil feedstocks than for typical petroleum feedstocks. A tendency for severely hydrogenated samples to gasify is at present the major qualification to the potential advantages of using shale oil as a petrochemical feedstock. To more fully define the sutiability of shale oil and prerefined shale oil as petrochemical feedstocks more thorough investigation of the liquid products is essential. A preliminary kinetics model was developed which consists of a reaction of feed shale oil to primary products, with subsequent reaction of these products to secondary products.

  13. Common clay and shale

    Science.gov (United States)

    Virta, R.L.

    2000-01-01

    Part of the 1999 Industrial Minerals Review. The clay and shale market in 1999 is reviewed. In the U.S., sales or use of clay and shale increased from 26.4 million st in 1998 to 27.3 million st in 1999, with an estimated 1999 value of production of $143 million. These materials were used to produce structural clay products, lightweight aggregates, cement, and ceramics and refractories. Production statistics for clays and shales and for their uses in 1999 are presented.

  14. Chattanooga Shale conference

    Energy Technology Data Exchange (ETDEWEB)

    1979-11-01

    Seven papers are included, relating to the exploitation of the uranium contained in shales. One of these papers discusses the IGT Hytort process, and was previously abstracted. Separate abstracts were prepared for the remaining six papers. (DLC)

  15. Biomarkers for environmental and occupational exposure to aromatic mutagens and carcinogens from emissions of oil shale petrochemistry. Report of the EC PECO programme, project CIPA-CT92-3016

    Energy Technology Data Exchange (ETDEWEB)

    Carere, A.; Crebelli, R. [eds.] [Istituto Superiore di Sanita`, Rome (Italy). Lab. di Tossicologia Comparata ed Ecotossicologia

    1998-03-01

    Oil shale processing for energy supply and further refining for petrochemistry is an important field of industry in Baltic countries. Estonia possesses the largest oil shale mines and oil shale processing plants of the world. Large scale oil shale extraction and processing lead to extensive environmental pollution and to the release of high levels of aromatic carcinogenic substances in processing plants. In the framework of the `PECO` programme, during 1993-1996, the European Commission funded a research project on biomarkers of environmental and occupational exposure in oil shale petrochemistry. The project gave the opportunity to develop and calibrate several biomarkers of exposure to aromatic carcinogens. The results obtained highlighted the role of blood benzene and urinary trans, trans-muconic acid and l-hydroxypyrene as sensitive biomarkers of occupational exposure to benzene and polycyclic aromatic hydrocarbons. A new promising approach was developed for the analysis of benzene adducts in haemoglobin. This methodology, as well as the {sup 32}P-postlabelling analysis of nulky adducts in DNA of blood cells of oil shale workers, showed high sensitivity and potential utility in human biomonitoring. Molecular cytogenetic methods based on in situ hybridization showed an exposure related clastogenic, and possibly an eugenic, effect in oil shale workers, demonstrating the potential advantage of new molecular approaches in the cytogenetic surveillance of carcinogen exposure. [Italiano] Gli scisti bituminosi costituiscono una materia prima di importanza prioritaria per l`industria petrolchimica dei paesi baltici. In Estonia, l`estrazione su larga scala degli scisti bituminosi ha prodotto una situazione di degrado ambientale, aggravata dalla emissione di considerevoli quantita` di sostanze cancerogene durante la lavorazione degli scisti negli impianti petrolchimici. Nell`ambito del programma di ricerca `PECO`, nel 1993-1996, l`Unione Europea ha finanziato un progetto

  16. Experience and prospects of oil shale utilization for power production in Russia

    Science.gov (United States)

    Potapov, O. P.

    2016-09-01

    Due to termination of work at the Leningrad Shale Deposit, the Russian shale industry has been liquidated, including not only shale mining and processing but also research and engineering (including design) activities, because this deposit was the only commercially operated complex in Russia. UTT-3000 plants with solid heat carrier, created mainly by the Russian specialists under scientific guidance of members of Krzhizhanovsky Power Engineering Institute, passed under the control of Estonian engineers, who, alongside with their operation in Narva, construct similar plants in Kohtla-Jarve, having renamed the Galoter Process into the Enifit or Petroter. The main idea of this article is to substantiate the expediency of revival of the oil shale industry in Russia. Data on the UTT-3000 plants' advantages, shale oils, and gas properties is provided. Information on investments in an UTT-3000 plant and estimated cost of Leningrad oil shale mining at the Mezhdurechensk Strip Mine is given. For more detailed technical and economic assessment of construction of a complex for oil shale extraction and processing, it is necessary to develop a feasibility study, which should be the first stage of this work. Creation of such a complex will make it possible to produce liquid and gaseous power fuel from oil shale of Leningrad Deposit and provide the opportunity to direct for export the released volumes of oil and gas for the purposes of Russian budget currency replenishment.

  17. A comparative assessment of the economic benefits from shale gas ...

    African Journals Online (AJOL)

    Kirstam

    2014-09-01

    Sep 1, 2014 ... coal bed gasification (proposed for the Waterberg coal fields) or further coal mining. If shale gas developments lead to a lower domestic gas price, it will impact on the appeal of both coal bed gasification and coal. The effects of a growing natural resource industry will vary based on the economic setting, the ...

  18. Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources

    Energy Technology Data Exchange (ETDEWEB)

    Spinti, Jennifer [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Birgenheier, Lauren [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Deo, Milind [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Facelli, Julio [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Hradisky, Michal [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Kelly, Kerry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Miller, Jan [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); McLennan, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ring, Terry [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Ruple, John [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States); Uchitel, Kirsten [Inst. for Clean and Secure Energy, Salt Lake City, UT (United States)

    2015-09-30

    This report summarizes the significant findings from the Clean and Secure Energy from Domestic Oil Shale and Oil Sands Resources program sponsored by the Department of Energy through the National Energy Technology Laboratory. There were four principle areas of research; Environmental, legal, and policy issues related to development of oil shale and oil sands resources; Economic and environmental assessment of domestic unconventional fuels industry; Basin-scale assessment of conventional and unconventional fuel development impacts; and Liquid fuel production by in situ thermal processing of oil shale Multiple research projects were conducted in each area and the results have been communicated via sponsored conferences, conference presentations, invited talks, interviews with the media, numerous topical reports, journal publications, and a book that summarizes much of the oil shale research relating to Utah’s Uinta Basin. In addition, a repository of materials related to oil shale and oil sands has been created within the University of Utah’s Institutional Repository, including the materials generated during this research program. Below is a listing of all topical and progress reports generated by this project and submitted to the Office of Science and Technical Information (OSTI). A listing of all peer-reviewed publications generated as a result of this project is included at the end of this report; Geomechanical and Fluid Transport Properties 1 (December, 2015); Validation Results for Core-Scale Oil Shale Pyrolysis (February, 2015); and Rates and Mechanisms of Oil Shale Pyrolysis: A Chemical Structure Approach (November, 2014); Policy Issues Associated With Using Simulation to Assess Environmental Impacts (November, 2014); Policy Analysis of the Canadian Oil Sands Experience (September, 2013); V-UQ of Generation 1 Simulator with AMSO Experimental Data (August, 2013); Lands with Wilderness Characteristics, Resource Management Plan Constraints, and Land Exchanges

  19. Suggestions on the development strategy of shale gas in China

    Directory of Open Access Journals (Sweden)

    Dazhong Dong

    2016-12-01

    Full Text Available From the aspects of shale gas resource condition, main exploration and development progress, important breakthrough in key technologies and equipment, this paper systematically summarized and analyzed current situation of shale gas development in China and pointed out five big challenges such as misunderstandings, lower implementation degree and higher economic uncertainty of shale gas resource, and still no breakthrough in exploration and development core technologies and equipment for shale gas buried depth more than 3500 m, higher cost and other non-technical factors that restrict the development pace. Aiming at the above challenges, we put forward five suggestions to promote the shale gas development in China: (1 Make strategies and set goals according to our national conditions and exploration and development stages. That is, make sure to realize shale gas annual production of 20 × 109 m3, and strives to reach 30 × 109 m3. (2 Attach importance to the research of accumulation and enrichment geological theory and exploration & development key engineering technologies for lower production and lower pressure marine shale gas reservoir, and at the same time orderly promote the construction of non-marine shale gas exploration & development demonstration areas. (3 The government should introduce further policies and set special innovation funds to support the companies to carry out research and development of related technologies and equipment, especially to strengthen the research and development of technology, equipment and process for shale gas bellow 3500 m in order to achieve breakthrough in deep shale gas. (4 Continue to promote the geological theory, innovation in technology and management, and strengthen cost control on drilling, fracturing and the whole process in order to realize efficient, economic and scale development of China's shale gas. (5 Reform the mining rights management system, establish information platform of shale

  20. A Transversely Isotropic Thermo-mechanical Framework for Oil Shale

    Science.gov (United States)

    Semnani, S. J.; White, J. A.; Borja, R. I.

    2014-12-01

    The present study provides a thermo-mechanical framework for modeling the temperature dependent behavior of oil shale. As a result of heating, oil shale undergoes phase transformations, during which organic matter is converted to petroleum products, e.g. light oil, heavy oil, bitumen, and coke. The change in the constituents and microstructure of shale at high temperatures dramatically alters its mechanical behavior e.g. plastic deformations and strength, as demonstrated by triaxial tests conducted at multiple temperatures [1,2]. Accordingly, the present model formulates the effects of changes in the chemical constituents due to thermal loading. It is well known that due to the layered structure of shale its mechanical properties in the direction parallel to the bedding planes is significantly different from its properties in the perpendicular direction. Although isotropic models simplify the modeling process, they fail to accurately describe the mechanical behavior of these rocks. Therefore, many researchers have studied the anisotropic behavior of rocks, including shale [3]. The current study presents a framework to incorporate the effects of transverse isotropy within a thermo-mechanical formulation. The proposed constitutive model can be readily applied to existing finite element codes to predict the behavior of oil shale in applications such as in-situ retorting process and stability assessment in petroleum reservoirs. [1] Masri, M. et al."Experimental Study of the Thermomechanical Behavior of the Petroleum Reservoir." SPE Eastern Regional/AAPG Eastern Section Joint Meeting. Society of Petroleum Engineers, 2008. [2] Xu, B. et al. "Thermal impact on shale deformation/failure behaviors---laboratory studies." 45th US Rock Mechanics/Geomechanics Symposium. American Rock Mechanics Association, 2011. [3] Crook, AJL et al. "Development of an orthotropic 3D elastoplastic material model for shale." SPE/ISRM Rock Mechanics Conference. Society of Petroleum Engineers

  1. Energy Return on Investment (EROI of Oil Shale

    Directory of Open Access Journals (Sweden)

    Peter A. O’Connor

    2011-11-01

    Full Text Available The two methods of processing synthetic crude from organic marlstone in demonstration or small-scale commercial status in the U.S. are in situ extraction and surface retorting. The considerable uncertainty surrounding the technological characterization, resource characterization, and choice of the system boundary for oil shale operations indicate that oil shale is only a minor net energy producer if one includes internal energy (energy in the shale that is used during the process as an energy cost. The energy return on investment (EROI for either of these methods is roughly 1.5:1 for the final fuel product. The inclusions or omission of internal energy is a critical question. If only external energy (energy diverted from the economy to produce the fuel is considered, EROI appears to be much higher. In comparison, fuels produced from conventional petroleum show overall EROI of approximately 4.5:1. “At the wellhead” EROI is approximately 2:1 for shale oil (again, considering internal energy and 20:1 for petroleum. The low EROI for oil shale leads to a significant release of greenhouse gases. The large quantities of energy needed to process oil shale, combined with the thermochemistry of the retorting process, produce carbon dioxide and other greenhouse gas emissions. Oil shale unambiguously emits more greenhouse gases than conventional liquid fuels from crude oil feedstocks by a factor of 1.2 to 1.75. Much of the discussion regarding the EROI for oil shale should be regarded as preliminary or speculative due to the very small number of operating facilities that can be assessed.

  2. A Study of Nonlinear Elasticity Effects on Permeability of Stress Sensitive Shale Rocks Using an Improved Coupled Flow and Geomechanics Model: A Case Study of the Longmaxi Shale in China

    Directory of Open Access Journals (Sweden)

    Chenji Wei

    2018-02-01

    Full Text Available Gas transport in shale gas reservoirs is largely affected by rock properties such as permeability. These properties are often sensitive to the in-situ stress state changes. Accurate modeling of shale gas transport in shale reservoir rocks considering the stress sensitive effects on rock petrophysical properties is important for successful shale gas extraction. Nonlinear elasticity in stress sensitive reservoir rocks depicts the nonlinear stress-strain relationship, yet it is not thoroughly studied in previous reservoir modeling works. In this study, an improved coupled flow and geomechanics model that considers nonlinear elasticity is proposed. The model is based on finite element methods, and the nonlinear elasticity in the model is validated with experimental data on shale samples selected from the Longmaxi Formation in Sichuan Basin China. Numerical results indicate that, in stress sensitive shale rocks, nonlinear elasticity affects shale permeability, shale porosity, and distributions of effective stress and pore pressure. Elastic modulus change is dependent on not only in-situ stress state but also stress history path. Without considering nonlinear elasticity, the modeling of shale rock permeability in Longmaxi Formation can overestimate permeability values by 1.6 to 53 times.

  3. Evaluation of excavation experience: Pierre shale. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Abel, J.F. Jr.; Gentry, D.W.

    1975-06-27

    Pierre shale and its stratigraphic equivalents represent a potentially favorable geologic environment for underground storage of hazardous waste products. These rock formations cover great areal and vertical extents, and represent some of the least permeable rock formations within the continental United States. There are, however, several engineering problems associated with constructing underground openings in Pierre shale. This formation is relatively weak and tends to deteriorate rather rapidly if not protected from the mine environment. It will be necessary to place all underground openings below the surficially weathered upper 50 to 70 feet of Pierre shale which contains groundwater moving on fracture permeability. The optimum site for disposal of hazardous waste in Pierre shale, or its stratigraphic equivalents, would be a seismically stable platform bounded on all sides by faults. The optimum size of individual openings would be the minimum necessary for access, storage, and retrieval of waste components. Underground excavations in Pierre shale must be made with care, must be of limited dimensions, must be widely spaced, must be protected from prolonged contact with the mine environment, must be supported immediately after excavation, and must be sited to avoid areas of faulting and(or) intense jointing. Underground openings constructed with boring machines and supported with wet shotcrete are recommended.

  4. In situ groundwater bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Hazen, Terry C.

    2009-02-01

    In situ groundwater bioremediation of hydrocarbons has been used for more than 40 years. Most strategies involve biostimulation; however, recently bioaugmentation have been used for dehalorespiration. Aquifer and contaminant profiles are critical to determining the feasibility and strategy for in situ groundwater bioremediation. Hydraulic conductivity and redox conditions, including concentrations of terminal electron acceptors are critical to determine the feasibility and strategy for potential bioremediation applications. Conceptual models followed by characterization and subsequent numerical models are critical for efficient and cost effective bioremediation. Critical research needs in this area include better modeling and integration of remediation strategies with natural attenuation.

  5. Anvil Points oil shale tailings management in Rifle, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Rudy, R.; Galli LaBerge, C.; McClurg, J. [Ecology and Environment Inc., Lancaster, NY (United States); Walsh Integrated, Lachine, PQ (Canada)

    2009-07-01

    This presentation summarized the oil shale tailings management program used at the Anvil Points mining site in Colorado. Decommissioning and reclamation of the site occurred between 1984 and 1986. The geology of the region is comprised of Tertiary bedrock sedimentary formations and Quaternary formations on the surface. Oil shales mined at the facility are from the Eocene Green River formation. While the site lies within big game winter ranges, the areas around the shale pile supports are not a significant nesting or feeding habitat for wildlife. No sensitive plants are located on the waste shale pile. The program currently includes revegetation test plots and the reclamation of an area where heating oil storage tanks were located. The dumping area is currently being monitored, and geophysical surveys are being conducted. Documents produced by mining activities are also being reviewed. Results of the study to date have indicated the presence of asbestos-containing materials, significant physical hazards, and significant cultural resources. An engineering evaluation and cost analysis has demonstrated that arsenic, beryllium, and iron exceed established soil screening levels. It was concluded that off-site removal actions will be conducted to prevent or reduce human exposure to the metals of concern. tabs., figs.

  6. Wet separation processes as method to separate limestone and oil shale

    Science.gov (United States)

    Nurme, Martin; Karu, Veiko

    2015-04-01

    Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

  7. Sex in situ

    DEFF Research Database (Denmark)

    Krøgholt, Ida

    2017-01-01

    Sex er en del af vores sociale praksis og centralt for det, vi hver især er. Men bortset fra pornoindustrien, har vi ikke mange muligheder for at få adgang til billeder af sex. Teater Nordkrafts forestilling Sex in situ vil gøre seksuelle billeder til noget, der kan deles, udveksles og tales om, og...

  8. Inherently safe in situ uranium recovery.

    Energy Technology Data Exchange (ETDEWEB)

    Krumhansl, James Lee; Beauheim, Richard Louis; Brady, Patrick Vane; Arnold, Bill Walter; Kanney, Joseph F.; McKenna, Sean Andrew

    2009-05-01

    Expansion of uranium mining in the United States is a concern to some environmental groups and sovereign Native American Nations. An approach which may alleviate some problems is to develop inherently safe in situ uranium recovery ('ISR') technologies. Current ISR technology relies on chemical extraction of trace levels of uranium from aquifers that, once mined, can still contain dissolved uranium and other trace metals that are a health concern. Existing ISR operations are few in number; however, high uranium prices are driving the industry to consider expanding operations nation-wide. Environmental concerns and enforcement of the new 30 ppb uranium drinking water standard may make opening new mining operations more difficult and costly. Here we propose a technological fix: the development of inherently safe in situ recovery (ISISR) methods. The four central features of an ISISR approach are: (1) New 'green' leachants that break down predictably in the subsurface, leaving uranium, and associated trace metals, in an immobile form; (2) Post-leachant uranium/metals-immobilizing washes that provide a backup decontamination process; (3) An optimized well-field design that increases uranium recovery efficiency and minimizes excursions of contaminated water; and (4) A combined hydrologic/geochemical protocol for designing low-cost post-extraction long-term monitoring. ISISR would bring larger amounts of uranium to the surface, leave fewer toxic metals in the aquifer, and cost less to monitor safely - thus providing a 'win-win-win' solution to all stakeholders.

  9. Characterization of raw and burnt oil shale from Dotternhausen: Petrographical and mineralogical evolution with temperature

    Energy Technology Data Exchange (ETDEWEB)

    Thiéry, Vincent, E-mail: vincent.thiery@mines-douai.fr [Mines Douai, LGCgE-GCE, F-59508 Douai (France); Université de Lille (France); Bourdot, Alexandra, E-mail: alexandra.bourdot@gmail.com [Mines Douai, LGCgE-GCE, F-59508 Douai (France); Bulteel, David, E-mail: david.bulteel@mines-douai.fr [Université de Lille (France)

    2015-08-15

    The Toarcian Posidonia shale from Dotternhausen, Germany, is quarried and burnt in a fluidized bed reactor to produce electricity. The combustion residue, namely burnt oil shale (BOS), is used in the adjacent cement work as an additive in blended cements. The starting material is a typical laminated oil shale with an organic matter content ranging from 6 to 18%. Mineral matter consists principally of quartz, feldspar, pyrite and clays. After calcination in the range, the resulting product, burnt oil shale, keeps the macroscopic layered texture however with different mineralogy (anhydrite, lime, iron oxides) and the formation of an amorphous phase. This one, studied under STEM, reveals a typical texture of incipient partial melting due to a long retention time (ca. 30 min) and quenching. An in-situ high temperature X-ray diffraction (HTXRD) allowed studying precisely the mineralogical changes associated with the temperature increase. - Highlights: • We present oil shale/burnt oil shale characterization. • The Posidonia Shale is burnt in a fluidized bed. • Mineralogical evolution with temperature is complex. • The burnt oil shale is used in composite cements.

  10. Creep of Posidonia Shale at Elevated Pressure and Temperature

    Science.gov (United States)

    Rybacki, E.; Herrmann, J.; Wirth, R.; Dresen, G.

    2017-12-01

    The economic production of gas and oil from shales requires repeated hydraulic fracturing operations to stimulate these tight reservoir rocks. Besides simple depletion, the often observed decay of production rate with time may arise from creep-induced fracture closure. We examined experimentally the creep behavior of an immature carbonate-rich Posidonia shale, subjected to constant stress conditions at temperatures between 50 and 200 °C and confining pressures of 50-200 MPa, simulating elevated in situ depth conditions. Samples showed transient creep in the semibrittle regime with high deformation rates at high differential stress, high temperature and low confinement. Strain was mainly accommodated by deformation of the weak organic matter and phyllosilicates and by pore space reduction. The primary decelerating creep phase observed at relatively low stress can be described by an empirical power law relation between strain and time, where the fitted parameters vary with temperature, pressure and stress. Our results suggest that healing of hydraulic fractures at low stresses by creep-induced proppant embedment is unlikely within a creep period of several years. At higher differential stress, as may be expected in situ at contact areas due to stress concentrations, the shale showed secondary creep, followed by tertiary creep until failure. In this regime, microcrack propagation and coalescence may be assisted by stress corrosion. Secondary creep rates were also described by a power law, predicting faster fracture closure rates than for primary creep, likely contributing to production rate decline. Comparison of our data with published primary creep data on other shales suggests that the long-term creep behavior of shales can be correlated with their brittleness estimated from composition. Low creep strain is supported by a high fraction of strong minerals that can build up a load-bearing framework.

  11. Lobular carcinoma in situ.

    Science.gov (United States)

    Afonso, Nelia; Bouwman, David

    2008-08-01

    The diagnosis of lobular carcinoma in situ (LCIS) provokes considerable anxiety in patients owing to misconceptions about this diagnosis. Initially LCIS was considered a premalignant lesion, but it is now a marker of increased risk. The number of women diagnosed with LCIS has increased in recent years most likely owing to more rigorous breast cancer screening. Implications of this diagnosis and management options are discussed in this review.

  12. Assessment of potential shale-oil and shale-gas resources in Silurian shales of Jordan, 2014

    Science.gov (United States)

    Schenk, Christopher J.; Pitman, Janet K.; Charpentier, Ronald R.; Klett, Timothy R.; Tennyson, Marilyn E.; Mercier, Tracey J.; Nelson, Philip H.; Brownfield, Michael E.; Pawlewicz, Mark J.; Wandrey, Craig J.

    2014-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 11 million barrels of potential shale-oil and 320 billion cubic feet of shale-gas resources in Silurian shales of Jordan.

  13. Mining under kalina and Selisoo Bogs

    OpenAIRE

    Otsmaa, Merle

    2015-01-01

    Continuous developing of Estonian power engineering on the basis of oil shale requires ever taking into use of new exploration fields. When the reserve of Estonia mine is depleted, mining of the exploration field of Seli has to be started. But that field is located under the Selisoo bog which is defined as a region of the Natura 2000 network and is planned become a nature preserve. Conservationists are interested for what extent oil shale mining under the Selisoo bog and in its immediate near...

  14. Total gas in-place calculations for the Baltic-Podlasie-Lublin basin shales in Poland

    Directory of Open Access Journals (Sweden)

    Lutynski Marcin A.

    2016-01-01

    Full Text Available The total gas in-place calculations reflecting Polish reservoir conditions were performed using a corrected version for the free gas in-place, where not only the pore conditions were taken under consideration but also the volume that was already occupied by the sorbed gas. Shales show very different capacities between samples mainly due to in-situ conditions.

  15. Chattanooga shale: an assessment of the resource and technology for the recovery of hydrocarbons and minerals

    Energy Technology Data Exchange (ETDEWEB)

    Spiewak, I.; Bomar, E.S.; Butz, T.R.

    1982-04-01

    Chattanooga shale, a large and mineral-rich member of the Devonian oil shales of the Eastern United States, is a resource of about 100 billion bbl of oil, 10 million tons of uranium, and significant quantities of other metals including aluminum, molybdenum, cobalt, columbium, and vanadium. Unlike coal and western oil shale, however, Chattanooga shale is not yet ready for commercial exploitation. The hydrocarbon content, while comparable to that of western shales, is more difficult to extract, and the metals, while generally more varied, are less concentrated than those of resources that are being exploited today. Although this study indicates that a large scale (100,000 tons/day) combined operation for oil and metals recovery appears to be economically attractive, commercial operations are presently impeded by the risks associated with the need for an extremely large capital investment and substantial unknowns with respect to envionmental effects and the methods for mining, processing, and waste disposal. Some of the principal technical problems that require resolution are those of roof stability and water intrusion associated with the underground mining of Chattanooga shale, the need for environmentally acceptable methods for disposal of tremendous quantities of spent shale, and the need for processes that can efficiently recover most of the hydrocarbon and mineral values with minimal loss of expensive processing reagents.

  16. Experimental Measurement of In Situ Stress

    Science.gov (United States)

    Tibbo, Maria; Milkereit, Bernd; Nasseri, Farzine; Schmitt, Douglas; Young, Paul

    2016-04-01

    The World Stress Map data is determined by stress indicators including earthquake focal mechanisms, in situ measurement in mining, oil and gas boreholes as well as the borehole cores, and geologic data. Unfortunately, these measurements are not only infrequent but sometimes infeasible, and do not provide nearly enough data points with high accuracy to correctly infer stress fields in deep mines around the world. Improvements in stress measurements of Earth's crust is fundamental to several industries such as oil and gas, mining, nuclear waste management, and enhanced geothermal systems. Quantifying the state of stress and the geophysical properties of different rock types is a major complication in geophysical monitoring of deep mines. Most stress measurement techniques involve either the boreholes or their cores, however these measurements usually only give stress along one axis, not the complete stress tensor. The goal of this project is to investigate a new method of acquiring a complete stress tensor of the in situ stress in the Earth's crust. This project is part of a comprehensive, exploration geophysical study in a deep, highly stressed mine located in Sudbury, Ontario, Canada, and focuses on two boreholes located in this mine. These boreholes are approximately 400 m long with NQ diameters and are located at depths of about 1300 - 1600 m and 1700 - 2000 m. Two borehole logging surveys were performed on both boreholes, October 2013 and July 2015, in order to perform a time-lapse analysis of the geophysical changes in the mine. These multi-parameter surveys include caliper, full waveform sonic, televiewer, chargeability (IP), and resistivity. Laboratory experiments have been performed on borehole core samples of varying geologies from each borehole. These experiments have measured the geophysical properties including elastic modulus, bulk modulus, P- and S-wave velocities, and density. The apparatus' used for this project are geophysical imaging cells capable

  17. Volume fracturing of deep shale gas horizontal wells

    Directory of Open Access Journals (Sweden)

    Tingxue Jiang

    2017-03-01

    Full Text Available Deep shale gas reservoirs buried underground with depth being more than 3500 m are characterized by high in-situ stress, large horizontal stress difference, complex distribution of bedding and natural cracks, and strong rock plasticity. Thus, during hydraulic fracturing, these reservoirs often reveal difficult fracture extension, low fracture complexity, low stimulated reservoir volume (SRV, low conductivity and fast decline, which hinder greatly the economic and effective development of deep shale gas. In this paper, a specific and feasible technique of volume fracturing of deep shale gas horizontal wells is presented. In addition to planar perforation, multi-scale fracturing, full-scale fracture filling, and control over extension of high-angle natural fractures, some supporting techniques are proposed, including multi-stage alternate injection (of acid fluid, slick water and gel and the mixed- and small-grained proppant to be injected with variable viscosity and displacement. These techniques help to increase the effective stimulated reservoir volume (ESRV for deep gas production. Some of the techniques have been successfully used in the fracturing of deep shale gas horizontal wells in Yongchuan, Weiyuan and southern Jiaoshiba blocks in the Sichuan Basin. As a result, Wells YY1HF and WY1HF yielded initially 14.1 × 104 m3/d and 17.5 × 104 m3/d after fracturing. The volume fracturing of deep shale gas horizontal well is meaningful in achieving the productivity of 50 × 108 m3 gas from the interval of 3500–4000 m in Phase II development of Fuling and also in commercial production of huge shale gas resources at a vertical depth of less than 6000 m.

  18. In-Situ Simulation

    DEFF Research Database (Denmark)

    Bjerregaard, Anders Thais; Slot, Susanne; Paltved, Charlotte

    2015-01-01

    for the in situ simulation program. Three scenarios were written and were double-checked by two medical experts. One researcher observed the training to score events and fill out the Team Emergency Assessment Measure (TEAM), a validated team observational tool set for measuring teamwork skills during medical...... emergencies. It contains 12 questions, which are rated using a five-point scale, and covers four categories; leadership, teamwork and task management, and an overall score on team performance. Results: 16 simulations were conducted with 16 different teams of 10 doctors and 32 nurses. First, this study took...

  19. Appraisal of transport and deformation in shale reservoirs using natural noble gas tracers

    Energy Technology Data Exchange (ETDEWEB)

    Heath, Jason E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kuhlman, Kristopher L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Robinson, David G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gardner, William Payton [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Univ. of Montana, Missoula, MT (United States)

    2015-09-01

    This report presents efforts to develop the use of in situ naturally-occurring noble gas tracers to evaluate transport mechanisms and deformation in shale hydrocarbon reservoirs. Noble gases are promising as shale reservoir diagnostic tools due to their sensitivity of transport to: shale pore structure; phase partitioning between groundwater, liquid, and gaseous hydrocarbons; and deformation from hydraulic fracturing. Approximately 1.5-year time-series of wellhead fluid samples were collected from two hydraulically-fractured wells. The noble gas compositions and isotopes suggest a strong signature of atmospheric contribution to the noble gases that mix with deep, old reservoir fluids. Complex mixing and transport of fracturing fluid and reservoir fluids occurs during production. Real-time laboratory measurements were performed on triaxially-deforming shale samples to link deformation behavior, transport, and gas tracer signatures. Finally, we present improved methods for production forecasts that borrow statistical strength from production data of nearby wells to reduce uncertainty in the forecasts.

  20. Surface water geochemical and isotopic variations in an area of accelerating Marcellus Shale gas development.

    Science.gov (United States)

    Pelak, Adam J; Sharma, Shikha

    2014-12-01

    Water samples were collected from 50 streams in an area of accelerating shale gas development in the eastern U.S.A. The geochemical/isotopic characteristics show no correlation with the five categories of Marcellus Shale production. The sub-watersheds with the greatest density of Marcellus Shale development have also undergone extensive coal mining. Hence, geochemical/isotopic compositions were used to understand sources of salinity and effects of coal mining and shale gas development in the area. The data indicates that while some streams appear to be impacted by mine drainage; none appear to have received sustained contribution from deep brines or produced waters associated with shale gas production. However, it is important to note that our interpretations are based on one time synoptic base flow sampling of a few sampling stations and hence do account potential intermittent changes in chemistry that may result from major/minor spills or specific mine discharges on the surface water chemistry. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. The Lower Jurassic Posidonia Shale in southern Germany: results of a shale gas analogue study

    Science.gov (United States)

    Biermann, Steffen; Schulz, Hans-Martin; Horsfield, Brian

    2013-04-01

    The shale gas potential of Germany was recently assessed by the Federal Institute for Geosciences and Natural Resources (2012 NiKo-Project) and is - in respect of the general natural gas occurrence in Germany - regarded as a good alternative hydrocarbon source. The Posidonia Shale in northern and southern Germany is one of the evaluated rock formation and easily accessible in outcrops in the Swabian Alps (southern Germany). The area of interest in this work is located in such an outcrop that is actively used for open pit mining next to the town of Dotternhausen, 70 km southwest of Stuttgart. 31 samples from the quarry of Dotternhausen were analyzed in order to characterize the immature Posidonia Shale (Lower Toarcian, Lias ɛ) of southern Germany as a gas shale precursor. Methods included are Rock Eval, Open Pyrolysis GC, SEM, Mercury Intrusion Porosimetry, XRD, and other. The samples of Dotternhausen contain exclusively type II kerogen. The majority of the organic matter is structureless and occurs in the argillaceous-calcareous matrix. Structured organic matter appears predominantly as alginite, in particular the algae "tasmanite" is noticeable. The TOC content ranges up to 16 wt% with a high bitumen content. The mineral content characterizes the Posidonia Shale as a marlstone or mudstone with varying clay-calcite ratios. The quartz and pyrite content reaches up to 20 wt% and 9 wt%, respectively. The rock fabric is characterized by a fine grained and laminated matrix. The mean porosity lies between 4 and 12 %. Fractures other than those introduced by sample preparation were not observed. The Posidonia Shale is predicted to have an excellent source rock potential and will generate intermediate, P-N-A low wax oil when exposed to higher P-T-conditions ("oil kitchen"). Contact surfaces between the kerogen and matrix will be vulnerable to pressure induced fracturing caused by hydrocarbon formation. Additional porosity will be formed during maturation due to the

  2. In situ measurement system

    Science.gov (United States)

    Lord, D.E.

    1980-11-24

    A multipurpose in situ underground measurement system comprising a plurality of long electrical resistance elements in the form of rigid reinforcing bars, each having an open loop hairpin configuration of shorter length than the other resistance elements. The resistance elements are arranged in pairs in a unitized structure, and grouted in place in the underground volume. Measurement means are provided for obtaining for each pair the electrical resistance of each element and the difference in electrical resistance of the paired elements, which difference values may be used in analytical methods involving resistance as a function of temperature. A scanner means sequentially connects the resistance-measuring apparatus to each individual pair of elements. A source of heating current is also selectively connectable for heating the elements to an initial predetermined temperature prior to electrical resistance measurements when used as an anemometer.

  3. Shale Gas Content Calculation of the Triassic Yanchang Formation in the Southeastern Ordos Basin, China

    Directory of Open Access Journals (Sweden)

    Jiao Su

    2017-11-01

    Full Text Available Shale gas content is the key parameter for shale gas potential evaluation and favorable area prediction. Therefore, it is very important to determine shale gas content accurately. Generally, we use the US Bureau of Mines (USBM method for coal reservoirs to calculate the gas content of shale reservoirs. However, shale reservoirs are different from coal reservoirs in depth, pressure, core collection, etc. This method would inevitably cause problems. In order to make the USBM method more suitable for shale reservoirs, an improved USBM method is put forward on the basis of systematic analysis of core pressure history and temperature history during shale gas degassing. The improved USBM method modifies the calculation method of the gas loss time, and determines the temperature balance time of water heating. In addition, we give the calculation method of adsorption gas content and free gas content, especially the new method of calculating the oil dissolved gas content and water dissolved gas content that are easily neglected. We used the direct method (USBM and the improved USBM and the indirect method (including the calculation of adsorption gas, free gas and the dissolved gas method to calculate the shale gas content of 16 shale samples of the Triassic Yanchang Formation in the Southeastern Ordos Basin, China. The results of the improved USBM method show that the total shale gas content is high, with an average of 3.97 m3/t, and the lost shale gas content is the largest proportion with an average of 62%. The total shale gas content calculated by the improved USBM method is greater than that of the USBM method. The results of the indirect method show that the total shale gas content is large, with an average of 4.11 m3/t, and the adsorption shale gas content is the largest proportion with an average of 71%. The oil dissolved shale gas content which should be paid attention to accounts for about 7.8%. The discrepancy between the direct method and

  4. Investigation of anistropic behavior of Montney Shale under indirect tensile strength test

    Energy Technology Data Exchange (ETDEWEB)

    Keneti, S.A.R.; Wong, R.C.K. [Calgary Univ., Calgary, AB (Canada)

    2010-07-01

    The Montney Shale Formation is located near the British Columbia and Alberta borders and is one of the largest economically feasible resource plays in North America. Hydraulic fracturing is used to enhance the gas production. Initiation and propagation of hydraulically induced fracture is controlled by in-situ stresses magnitude and orientation and the reservoir tensile strength. The tensile strength becomes one of the most important parameters in governing hydraulic fracturing of the reservoir if the in-situ stresses composing one vertical and two horizontal stresses are comparable or lie within a narrow range. Different point and line load tests were used in this study to determine the tensile strength of Montney shale cores in two perpendicular directions. The paper discussed image analysis of Montney shale cores and tensile strength tests, including Brazilian tests for measuring tensile strength in the horizontal direction and point load tests for measuring tensile strength in the vertical direction. The effect of anisotropic tensile strength on hydraulic fracturing of Montney shale was also presented. It was concluded from the test results that the Montney shale exhibits a high anisotropy in tensile strength. 11 refs., 3 tabs., 11 figs.

  5. Jet Fuel Looks to Shale Oil: 1980 Technology Review.

    Science.gov (United States)

    1981-05-01

    Potential Yields from Phases I and II BASlS: 100,0W 11po IN SITU SHALE OIL Yield Estimate, Net Volume Percent Products Phase I Phase It Propane 0.6 2.8...proprietary catalysts for use in the various catalytic processing units. Main hydro- treater catalyst aging tests were performed. A six-month run...104 45.0 104 45.0 104 45.0 DIST. HYDROTREATER, MBPSD 25 31.5 28 34.4 25 31.5 HCL TREATER , MBPSD 74 2.4 61 2.3 74 2.4 HYDROCRACKER 9 ATM. DISNT., MBPSD

  6. Characterization of oil shale, isolated kerogen, and post-pyrolysis residues using advanced 13 solid-state nuclear magnetic resonance spectroscopy

    Science.gov (United States)

    Cao, Xiaoyan; Birdwell, Justin E.; Chappell, Mark A.; Li, Yuan; Pignatello, Joseph J.; Mao, Jingdong

    2013-01-01

    Characterization of oil shale kerogen and organic residues remaining in postpyrolysis spent shale is critical to the understanding of the oil generation process and approaches to dealing with issues related to spent shale. The chemical structure of organic matter in raw oil shale and spent shale samples was examined in this study using advanced solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. Oil shale was collected from Mahogany zone outcrops in the Piceance Basin. Five samples were analyzed: (1) raw oil shale, (2) isolated kerogen, (3) oil shale extracted with chloroform, (4) oil shale retorted in an open system at 500°C to mimic surface retorting, and (5) oil shale retorted in a closed system at 360°C to simulate in-situ retorting. The NMR methods applied included quantitative direct polarization with magic-angle spinning at 13 kHz, cross polarization with total sideband suppression, dipolar dephasing, CHn selection, 13C chemical shift anisotropy filtering, and 1H-13C long-range recoupled dipolar dephasing. The NMR results showed that, relative to the raw oil shale, (1) bitumen extraction and kerogen isolation by demineralization removed some oxygen-containing and alkyl moieties; (2) unpyrolyzed samples had low aromatic condensation; (3) oil shale pyrolysis removed aliphatic moieties, leaving behind residues enriched in aromatic carbon; and (4) oil shale retorted in an open system at 500°C contained larger aromatic clusters and more protonated aromatic moieties than oil shale retorted in a closed system at 360°C, which contained more total aromatic carbon with a wide range of cluster sizes.

  7. Western states enhanced oil shale recovery program: Shale oil production facilities conceptual design studies report

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-01

    This report analyzes the economics of producing syncrude from oil shale combining underground and surface processing using Occidental's Modified-In-Situ (MIS) technology and Lawrence Livermore National Laboratory's (LLNL) Hot Recycled Solids (HRS) retort. These retorts form the basic technology employed for oil extraction from oil shale in this study. Results are presented for both Commercial and Pre-commercial programs. Also analyzed are Pre-commercialization cost of Demonstration and Pilot programs which will confirm the HRS and MIS concepts and their mechanical designs. These programs will provide experience with the circulating Fluidized Bed Combustor (CFBC), the MIS retort, the HRS retort and establish environmental control parameters. Four cases are considered: commercial size plant, demonstration size plant, demonstration size plant minimum CFBC, and a pilot size plant. Budget cost estimates and schedules are determined. Process flow schemes and basic heat and material balances are determined for the HRS system. Results consist of summaries of major equipment sizes, capital cost estimates, operating cost estimates and economic analyses. 35 figs., 35 tabs.

  8. BLM Colorado Oil Shale Leases

    Data.gov (United States)

    Department of the Interior — KMZ File Format –This data set contains the Oil Shale Leases for the State of Colorado, derived from Legal Land Descriptions (LLD) contained in the US Bureau of Land...

  9. Two-step processing of oil shale to linear hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Eliseev, O.L.; Ryzhov, A.N.; Latypova, D.Zh.; Lapidus, A.L. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry; Avakyan, T.A. [Gubkin Russian State University of Oil and Gas, Moscow (Russian Federation)

    2013-11-01

    Thermal and catalytic steam reforming of oil shale mined from Leningrad and Kashpir deposits was studied. Experiments were performed in fixed bed reactor by varying temperature and steam flow rate. Data obtained were approximated by empirical formulas containing some parameters calculated by least-squares method. Thus predicting amount of hydrogen, carbon monoxide and methane in producer gas is possible for given particular kind of oil shale, temperature and steam flow rate. Adding Ni catalyst enriches hydrogen and depletes CO content in effluent gas at low gasification temperatures. Modeling gas simulating steam reforming gases (H{sub 2}, CO, CO{sub 2}, and N{sub 2} mixture) was tested in hydrocarbon synthesis over Co-containing supported catalyst. Selectivity of CO conversion into C{sub 5+} hydrocarbons reaches 84% while selectivity to methane is 7%. Molecular weight distribution of synthesized alkanes obeys Anderson-Schulz-Flory equation and chain growth probability 0.84. (orig.)

  10. Proof-of-Concept Oil Shale Facility Environmental Analysis Program

    Energy Technology Data Exchange (ETDEWEB)

    1990-11-01

    The objectives of the Project are to demonstrate: (1) the Modified In- Situ (MIS) shale oil extraction process and (2) the application of CFBC technology using oil shale, coal and waste gas streams as fuels. The project will focus on evaluating and improving the efficiency and environmental performance of these technologies. The project will be modest by commercial standards. A 17-retort MIS system is planned in which two retorts will be processed simultaneously. Production of 1206-barrels per calendar day of raw shale oil and 46-megawatts of electricity is anticipated. West Virginia University coordinated an Environmental Analysis Program for the Project. Experts from around the country were retained by WVU to prepare individual sections of the report. These experts were exposed to all of OOSI`s archives and toured Tract C-b and Logan Wash. Their findings were incorporated into this report. In summary, no environmental obstacles were revealed that would preclude proceeding with the Project. One of the most important objectives of the Project was to verify the environmental acceptability of the technologies being employed. Consequently, special attention will be given to monitoring environmental factors and providing state of the art mitigation measures. Extensive environmental and socioeconomic background information has been compiled for the Tract over the last 15 years and permits were obtained for the large scale operations contemplated in the late 1970`s and early 1980`s. Those permits have been reviewed and are being modified so that all required permits can be obtained in a timely manner.

  11. Fluidized-bed retorting of Colorado oil shale: Topical report. [None

    Energy Technology Data Exchange (ETDEWEB)

    Albulescu, P.; Mazzella, G.

    1987-06-01

    In support of the research program in converting oil shale into useful forms of energy, the US Department of Energy is developing systems models of oil shale processing plants. These models will be used to project the most attractive combination of process alternatives and identify future direction for R and D efforts. With the objective of providing technical and economic input for such systems models, Foster Wheeler was contracted to develop conceptual designs and cost estimates for commercial scale processing plants to produce syncrude from oil shales via various routes. This topical report summarizes the conceptual design of an integrated oil shale processing plant based on fluidized bed retorting of Colorado oil shale. The plant has a nominal capacity of 50,000 barrels per operating day of syncrude product, derived from oil shale feed having a Fischer Assay of 30 gallons per ton. The scope of the plant encompasses a grassroots facility which receives run of the mine oil shale, delivers product oil to storage, and disposes of the processed spent shale. In addition to oil shale feed, the battery limits input includes raw water, electric power, and natural gas to support plant operations. Design of the individual processing units was based on non-confidential information derived from published literature sources and supplemented by input from selected process licensors. The integrated plant design is described in terms of the individual process units and plant support systems. The estimated total plant investment is similarly detailed by plant section and an estimate of the annual operating requirements and costs is provided. In addition, the process design assumptions and uncertainties are documented and recommendations for process alternatives, which could improve the overall plant economics, are discussed.

  12. In Situ TEM Electrical Measurements

    DEFF Research Database (Denmark)

    Canepa, Silvia; Alam, Sardar Bilal; Ngo, Duc-The

    2016-01-01

    and measurement of the specimen. Recognizing the benefits of electrical measurements for in situ TEM, many research groups have focused their effort in this field and some of these methods have transferred to ETEM. This chapter will describe recent advances in the in situ TEM investigation of nanostructured...... materials and devices with the specimen being contacted by electrical, mechanical or other means, with emphasis on in situ electrical measurements performed in a gaseous or liquid environment. We will describe the challenges and prospects of electrical characterization of devices and processes induced...... by a voltage in gas and liquids. We will also provide a historical perspective of in situ TEM electrical measurements and applications using electrical contacts....

  13. In Situ Aerosol Detector Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA is developing new platform systems that have the potential to benefit Earth science research activities, which include in situ instruments for atmospheric...

  14. Reconstruction of paleoenvironment recorded in the Ediacaran Lantain black shales

    Science.gov (United States)

    Liu, Y. H.; Lee, D. C.; You, C. F.; Zhou, C.

    2016-12-01

    The Ediacaran period (635-542 Ma) was a critical time in the history of life and Earth, during which profound changes in complex megascopic life and probably ocean oxygenation occurred. A growing evidence demonstrates that the Early Ediacaran ocean was not simply a largely anoxic basin as previous thought. Pulsed oxidation or a multilayered water column had been proposed to explain the presence of Lantain macrofossils. To verify these models, in-situ isotopic analysis becomes critical in identifying the isotopic signatures of authigenic minerals, and to avoid mixing in the signals from detrital and diagenetic phases. In this study, samples from Lantain Member II, a 40 m thick black shale unit containing macrofossils and overlaying the cap carbonate, were analyzed, including one sample from the lower part of Member II and six samples from upper part of Member II. Abundant xenotimes were overgrown on the detrital zircon grains during early diagenesis in all the samples. This authigenic phosphate mineral provides the best constraint of depositional age. In addition, framboidal pyrites and microbial mats are alternatively present on the top of Member II, where layered barites are found in one sample, supporting the model of frequent changes of redox conditions. Preliminary results show that the depositional age of barite-bearing black shale is > 520 Ma. In this study, we will combine the in-situ U-Pb xenotime dating and sulfur isotopes in barite and pyrite to discuss the evolution of redox conditions in the Ediacaran ocean.

  15. A new laboratory approach to shale analysis using NMR relaxometry

    Science.gov (United States)

    Washburn, Kathryn E.; Birdwell, Justin E.; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

    2013-01-01

    Low-field nuclear magnetic resonance (LF-NMR) relaxometry is a non-invasive technique commonly used to assess hydrogen-bearing fluids in petroleum reservoir rocks. Measurements made using LF-NMR provide information on rock porosity, pore-size distributions, and in some cases, fluid types and saturations (Timur, 1967; Kenyon et al., 1986; Straley et al., 1994; Brown, 2001; Jackson, 2001; Kleinberg, 2001; Hurlimann et al., 2002). Recent improvements in LF-NMR instrument electronics have made it possible to apply methods used to measure pore fluids to assess highly viscous and even solid organic phases within reservoir rocks. T1 and T2 relaxation responses behave very differently in solids and liquids; therefore the relationship between these two modes of relaxation can be used to differentiate organic phases in rock samples or to characterize extracted organic materials. Using T1-T2 correlation data, organic components present in shales, such as kerogen and bitumen, can be examined in laboratory relaxometry measurements. In addition, implementation of a solid-echo pulse sequence to refocus T2 relaxation caused by homonuclear dipolar coupling during correlation measurements allows for improved resolution of solid-phase protons. LF-NMR measurements of T1 and T2 relaxation time distributions were carried out on raw oil shale samples from the Eocene Green River Formation and pyrolyzed samples of these shales processed by hydrous pyrolysis and techniques meant to mimic surface and in-situ retorting. Samples processed using the In Situ Simulator approach ranged from bitumen and early oil generation through to depletion of petroleum generating potential. The standard T1-T2 correlation plots revealed distinct peaks representative of solid- and liquid-like organic phases; results on the pyrolyzed shales reflect changes that occurred during thermal processing. The solid-echo T1 and T2 measurements were used to improve assessment of the solid organic phases, specifically

  16. In Situ Activation of Microcapsules

    Science.gov (United States)

    Morrison, Dennis R. (Inventor); Mosier, Benjamin (Inventor)

    2000-01-01

    Disclosed are microcapsules comprising a polymer shell enclosing two or more immiscible liquid phases in which a drug, or a prodrug and a drug activator are partitioned into separate phases. or prevented from diffusing out of the microcapsule by a liquid phase in which the drug is poorly soluble. Also disclosed are methods of using the microcapsules for in situ activation of drugs where upon exposure to an appropriate energy source the internal phases mix and the drug is activated in situ.

  17. Molecular characterization and comparison of shale oils generated by different pyrolysis methods using FT-ICR mass spectrometry

    Science.gov (United States)

    Jin, J.M.; Kim, S.; Birdwell, J.E.

    2011-01-01

    Fourier transform ion cyclotron resonance mass spectrometry (FT ICR-MS) was applied in the analysis of shale oils generated using two different pyrolysis systems under laboratory conditions meant to simulate surface and in situ oil shale retorting. Significant variations were observed in the shale oils, particularly the degree of conjugation of the constituent molecules. Comparison of FT ICR-MS results to standard oil characterization methods (API gravity, SARA fractionation, gas chromatography-flame ionization detection) indicated correspondence between the average Double Bond Equivalence (DBE) and asphaltene content. The results show that, based on the average DBE values and DBE distributions of the shale oils examined, highly conjugated species are enriched in samples produced under low pressure, high temperature conditions and in the presence of water.

  18. Impacts of bedding directions of shale gas reservoirs on hydraulically induced crack propagation

    Directory of Open Access Journals (Sweden)

    Keming Sun

    2016-03-01

    Full Text Available Shale gas reservoirs are different from conventional ones in terms of their bedding architectures, so their hydraulic fracturing rules are somewhat different. In this paper, shale hydraulic fracturing tests were carried out by using the triaxial hydraulic fracturing test system to identify the effects of natural bedding directions on the crack propagation in the process of hydraulic fracturing. Then, the fracture initiation criterion of hydraulic fracturing was prepared using the extended finite element method. On this basis, a 3D hydraulic fracturing computation model was established for shale gas reservoirs. And finally, a series of studies were performed about the effects of bedding directions on the crack propagation created by hydraulic fracturing in shale reservoirs. It is shown that the propagation rules of hydraulically induced fractures in shale gas reservoirs are jointly controlled by the in-situ stress and the bedding plane architecture and strength, with the bedding direction as the main factor controlling the crack propagation directions. If the normal tensile stress of bedding surface reaches its tensile strength after the fracturing, cracks will propagate along the bedding direction, and otherwise vertical to the minimum in-situ stress direction. With the propagating of cracks along bedding surfaces, the included angle between the bedding normal direction and the minimum in-situ stress direction increases, the fracture initiation and propagation pressures increase and the crack areas decrease. Generally, cracks propagate in the form of non-plane ellipsoids. With the injection of fracturing fluids, crack areas and total formation filtration increase and crack propagation velocity decreases. The test results agree well with the calculated crack propagation rules, which demonstrate the validity of the above-mentioned model.

  19. LLNL oil shale project review

    Energy Technology Data Exchange (ETDEWEB)

    Cena, R.J. (ed.)

    1990-04-01

    Livermore's oil shale project is funded by two budget authorities, two thirds from base technology development and one third from environmental science. Our base technology development combines fundamental chemistry research with operation of pilot retorts and mathematical modeling. We've studied mechanisms for oil coking and cracking and have developed a detailed model of this chemistry. We combine the detailed chemistry and physics into oil shale process models (OSP) to study scale-up of generic second generation Hot-Recycled-Solid (HRS) retorting systems and compare with results from our 4 tonne-per-day continuous-loop HRS pilot retorting facility. Our environmental science program focuses on identification of gas, solid and liquid effluents from oil shale processes and development of abatement strategies where necessary. We've developed on-line instruments to quantitatively measure trace sulfur and nitrogen compounds released during shale pyrolysis and combustion. We've studied shale mineralogy, inorganic and organic reactions which generate and consume environmentally sensitive species. Figures, references, and tables are included with each discussion.

  20. Inferences from Microfractures and Geochemistry in Dynamic Shale-CO2 Packed Bed Experiments

    Science.gov (United States)

    Radonjic, M.; Olabode, A.

    2016-12-01

    Subsurface storage of large volumes of carbondioxide (CO2) is expected to have long term rock-fluid interactions impact on reservoir and seal rocks properties. Caprocks, particularly sedimentary types, are the ultimate hydraulic barrier in carbon sequestration. The mineralogical components of sedimentary rocks are geochemically active under enormous earth stresses, which generate high pressure and temperature conditions. It has been postulated that in-situ mineralization can lead to flow impedance in natural fractures in the presence of favorable geochemical and thermodynamic conditions. This experimental modelling research investigated the impact of in-situ geochemical precipitation on conductivity of fractures. Geochemical analyses were performed on four different samples of shale rocks, effluent fluids and recovered precipitates both before and after CO2-brine flooding of crushed shale rocks at moderately high temperature and pressure conditions. The results showed that most significant diagenetic changes in shale rocks after flooding with CO2-brine, reflected in the effluent fluid with predominantly calcium based minerals dissolving and precipitating under experimental conditions. Major and trace elements in the effluent (using ICP-OES analysis) indicated that multiple geochemical reactions are occurring with almost all of the constituent minerals participating. The geochemical composition of precipitates recovered after the experiments showed diagenetic carbonates and opal as the main constituents. The bulk rock showed little changes in composition except for sharper and more refined peaks on XRD analysis, suggesting that a significant portion of the amorphous content of the rocks have been removed via dissolution by the slightly acid CO2-brine fluid that was injected. Micro-indentation results captured slight reduction in the hardness of the shale rocks and this reduction appeared dependent on diagenetic quartz content. It can be inferred that convective

  1. Searching for anomalous methane in shallow groundwater near shale gas wells.

    Science.gov (United States)

    Li, Zhenhui; You, Cheng; Gonzales, Matthew; Wendt, Anna K; Wu, Fei; Brantley, Susan L

    2016-12-01

    Since the 1800s, natural gas has been extracted from wells drilled into conventional reservoirs. Today, gas is also extracted from shale using high-volume hydraulic fracturing (HVHF). These wells sometimes leak methane and must be re-sealed with cement. Some researchers argue that methane concentrations, C, increase in groundwater near shale-gas wells and that "fracked" wells leak more than conventional wells. We developed techniques to mine datasets of groundwater chemistry in Pennsylvania townships where contamination had been reported. Values of C measured in shallow private water wells were discovered to increase with proximity to faults and to conventional, but not shale-gas, wells in the entire area. However, in small subareas, C increased with proximity to some shale-gas wells. Data mining was used to map a few hotspots where C significantly correlates with distance to faults and gas wells. Near the hotspots, 3 out of 132 shale-gas wells (~2%) and 4 out of 15 conventional wells (27%) intersect faults at depths where they are reported to be uncased or uncemented. These results demonstrate that even though these data techniques do not establish causation, they can elucidate the controls on natural methane emission along faults and may have implications for gas well construction. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Ensilin Tests on Selected Clays and Shales

    Science.gov (United States)

    1989-05-01

    are one of the most difficult formations to drill effectively. Shales are sedimentary rocks deposited in a marine environment that contain silt and...minerals are exposed to water in drilling fluids, they swell, disperse and eventually cause wellbore instabilities. This leads to many problems in...of the numerous works on shale classification and shale control. 2.1 Clays In order to understand shale instability, one must first look at the

  3. Investigation of Controlling Factors Impacting Water Quality in Shale Gas Produced Brine

    Science.gov (United States)

    Fan, W.; Hayes, K. F.; Ellis, B. R.

    2014-12-01

    The recent boom in production of natural gas from unconventional reservoirs has generated a substantial increase in the volume of produced brine that must be properly managed to prevent contamination of fresh water resources. Produced brine, which includes both flowback and formation water, is often highly saline and may contain elevated concentrations of naturally occurring radioactive material and other toxic elements. These characteristics present many challenges with regard to designing effective treatment and disposal strategies for shale gas produced brine. We will present results from a series of batch experiments where crushed samples from two shale formations in the Michigan Basin, the Antrim and Utica-Collingwood shales, were brought into contact with synthetic hydraulic fracturing fluids under in situ temperature and pressure conditions. The Antrim has been an active shale gas play for over three decades, while the Utica-Collingwood formation (a grouped reservoir consisting of the Utica shale and Collingwood limestone) is an emerging shale gas play. The goal of this study is to investigate the influence of water-rock interactions in controlling produced water quality. We evaluate toxic element leaching from shale samples in contact with model hydraulic fracturing fluids under system conditions corresponding to reservoir depths up to 1.5 km. Experimental results have begun to elucidate the relative importance of shale mineralogy, system conditions, and chemical additives in driving changes in produced water quality. Initial results indicate that hydraulic fracturing chemical additives have a strong influence on the extent of leaching of toxic elements from the shale. In particular, pH was a key factor in the release of uranium (U) and divalent metals, highlighting the importance of the mineral buffering capacity of the shale. Low pH values persisted in the Antrim and Utica shale experiments and resulted in higher U extraction efficiencies than that

  4. Technical support for GEIS: radioactive waste isolation in geologic formations. Volume 12. Repository preconceptual design studies: shale

    Energy Technology Data Exchange (ETDEWEB)

    1978-04-01

    This document describes a preconceptual design for a nuclear waste storage facility in shale. The facility design consists of several chambers excavated deep within a geologic formation together with access shafts and supportive surface structures. The facility design provides for: receiving and unloading waste containers; lowering them down shafts to the mine level; transporting them to the proper storage area, and emplacing them in mined storage rooms. Drawings of the facility design are contained in TM-36/13, ''Drawings for Repository Preconceptual Design Studies: Shale.''

  5. Fourier Transform Infrared Spectroscopic Determination of Shale ...

    African Journals Online (AJOL)

    acer

    The presence of gas in place requires adequate gas generative organic matter to generate either biogenic or thermogenic gas, and to retain significant gas. The shale gas petroleum system is self- contained. Shales act as the critical lithological units for most or all the key components of the shale gas petroleum system.

  6. An assessment of using oil shale for power production in the Hashemite Kingdom of Jordan

    Energy Technology Data Exchange (ETDEWEB)

    Hill, L.J.; Holcomb, R.S.; Petrich, C.H.; Roop, R.D.

    1990-11-01

    This report addresses the oil shale-for-power-production option in Jordan. Under consideration are 20- and 50-MW demonstration units and a 400-MW, commercial-scale plant with, at the 400-MW scale, a mining operation capable of supplying 7.8 million tonnes per year of shale fuel and also capable of disposal of up to 6.1 million tonnes per year of wetted ash. The plant would be a direct combustion facility, burning crushed oil shale through use of circulating fluidized bed combustion technology. The report emphasizes four areas: (1) the need for power in Jordan, (2) environmental aspects of the proposed oil shale-for-power plant(s), (3) the engineering feasibility of using Jordan's oil shale in circulating fluidized bed combustion (CFBC) boiler, and (4) the economic feasibility of the proposed plant(s). A sensitivity study was conducted to determine the economic feasibility of the proposed plant(s) under different cost assumptions and revenue flows over the plant's lifetime. The sensitivity results are extended to include the major extra-firm benefits of the shale-for-power option: (1) foreign exchange savings from using domestic energy resources, (2) aggregate income effects of using Jordan's indigenous labor force, and (3) a higher level of energy security. 14 figs., 47 tabs.

  7. Paraho Oil Shale Project. [Review of accomplishments of operation of Rifle, Colorado facility since 1973

    Energy Technology Data Exchange (ETDEWEB)

    Pforzheimer, H.

    1976-01-01

    The Paraho Oil Shale Demonstration is a privately financed project sponsored by seventeen participants. The program to demonstrate the Paraho technology on oil shale is being conducted at the Anvil Points Experiment Station of the Energy Research and Development Administration (ERDA). The facility is located on the Naval Oil Shale Reserve near Rifle, Colorado. A $9 million, 34 month, mining, retorting and disposal program is scheduled for completion by mid 1976. A large pilot plant and a semi-works scale plant were erected and put into operation in 1974. Two modes of operation, direct and indirect heating, have been successfully demonstrated. Large scale refining of crude shale oil and retorted shale management experiments have been carried out. The extended retorting demonstration runs on Paraho's cylindrical, vertical shaft kilns have characterized this new technology as environmentally acceptable, with high liquid recovery, high thermal efficiency and low water consumption. The demonstration operations and the outlook for the commercial development of oil shale are discussed.

  8. Refining of Military Jet Fuels from Shale Oil. Part II. Volume II. (In Situ Shale Oil Process Data).

    Science.gov (United States)

    1982-03-01

    W Bottoms, Sediment and Water BTU British Thermal Unit I "C Degrees Celsius C Carbon or Heteroatom Concentration Cl Methane C2 Ethane C3 Propane C3...DISCUSSION These runs were the first in which full-range hydro- treater product was charged to the cracker in an effort to take advantage of both the

  9. Maquoketa Shale Caprock Integrity Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Leetaru, Hannes

    2014-09-30

    The Knox Project objective is to evaluate the potential of formations within the Cambrian-Ordovician strata above the Mt. Simon Sandstone (St. Peter Sandstone and Potosi Dolomite) as potential targets for carbon dioxide (CO2) sequestration in the Illinois and Michigan Basins. The suitability of the St. Peter Sandstone and Potosi Dolomite to serve as reservoirs for CO2 sequestration is discussed in separate reports. In this report the data gathered from the Knox project, the Illinois Basin – Decatur Project (IBDP) and Illinois Industrial Carbon Capture and Sequestration project (IL-ICCS) are used to make some conclusions about the suitability of the Maquoketa shale as a confining layer for CO2 sequestration. These conclusions are then upscaled to basin-wide inferences based on regional knowledge. Data and interpretations (stratigraphic, petrophysical, fractures, geochemical, risk, seismic) applicable to the Maquoketa Shale from the above mentioned projects was inventoried and summarized. Based on the analysis of these data and interpretations, the Maquoketa Shale is considered to be an effective caprock for a CO2 injection project in either the Potosi Dolomite or St. Peter Sandstone because it has a suitable thickness (~200ft. ~61m), advantageous petrophysical properties (low effective porosity and low permeability), favorable geomechanical properties, an absence of observable fractures and is regionally extensive. Because it is unlikely that CO2 would migrate upward through the Maquoketa Shale, CO2, impact to above lying fresh water aquifers is unlikely. Furthermore, the observations indicate that CO2 injected into the St. Peter Sandstone or Potosi Dolomite may never even migrate up into the Maquoketa Shale at a high enough concentrations or pressure to threaten the integrity of the caprock. Site specific conclusions were reached by unifying the data and conclusions from the IBDP, ICCS and the Knox projects. In the Illinois Basin, as one looks further away from

  10. Surface Disturbance Analysis in Rare Earth Mining

    Science.gov (United States)

    Li, H. K.; Yang, L.; Liu, Z. W.

    2017-02-01

    Mining ion-type rare-earth ore made the landscape and ecological environment degraded in mining area, and the tailing produced by rare-earth mining also led large areas land desertification, which resulted in surface temperature variations and significant differences in other types of mining disturbances. In order to analyse surface disturbance of rare-earth mining area, this paper applied the methods based on Normalized Difference Vegetation Index (NDVI) and Temperature different Coefficient (TDC) as the ecological disturbance indicator, compared and validated their applicability in Lingbei rare-earth mining area of Southern China. The results illustrated that, compared to NDVI, the TDC which reflected the characteristic of rare-earth mining technology has better discrimination of disturbance, especially for in-situ leach mining area. The places of tailing and the in-situ leach mining plants were the most dramatic mining disturbance. They had the biggest TDC value, followed by orchards and farmlands, reclamation plants, they had relatively small disturbance. And the last was the plant with the smallest TDC value. TDC in rare-earth mining could better correspond to the level of surface ecological disturbance. Therefore, TDC as the indicator of ecological disturbance factor had better performance than NDVI in rare-earth mining area.

  11. Field and Lab-Based Microbiological Investigations of the Marcellus Shale

    Science.gov (United States)

    Wishart, J. R.; Neumann, K.; Edenborn, H. M.; Hakala, A.; Yang, J.; Torres, M. E.; Colwell, F. S.

    2013-12-01

    even when samples were spiked with 8x108 cells/g of shale. This indicated that constituents of shale such as high levels of carbonates, humic acids and metals likely inhibited components of the PowerSoil kit. Future research is focused on refining sample collection and analyses to gain a full understanding of the microbiology of the Marcellus shale and associated flowback fluids. This includes the development of an in situ osmosampler, which will collect temporally relevant fluid and colonized substrate samples. The design of the osmosampler for hydraulic fracturing wells is being adapted from those used to sample marine environments. Furthermore, incubation experiments are underway to study interactions between microbial communities associated with hydraulic fracturing fluid and Marcellus shale samples. In conclusion, evidence suggests that the Marcellus shale is a possible component of the subsurface biosphere. Future studies will be valuable in determining the microbial community structure and function in relation to the geochemistry of the Marcellus shale and its future development as a natural gas resource.

  12. Health effects research in oil shale development

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, T.W.; Witschi, H.; Smith, L.H.; Haschek, W.M.; Holland, J.M.; Epler, J.L.; Fry, R.J.M.; Rao, T.K.; Larimer, F.W.; Dumont, J.N.

    1981-11-01

    This task includes the testing of primary effluents and products of oil shales to determine the risk posed to the shale oil industrial worker as well as consumer. Paraho/Sohio Shale Oil was found to be mutagenic in the Ames assay and confirmed in the yeast system. After chemical fractionation of the crude shale oil, it was found that the mutagenic activity was contributed by the organic constituents of the basic and neutral fractions. Hydrotreatment of the shale oil abolished the detectable mutagenic activity and also reduced the cytotoxicity as measured in cellular systems. Refined shale oil, jet fuel, and diesel fuel marine samples were not mutagenic. The samples rank for their mutagenic activity as coal oils > shale oil > natural petroleum crudes and only qualitatively agree with carcinogenic activity. Acute toxicity of Paraho Crude Shale Oil and its upgraded derivatives does not appear to be a problem of immediate concern. The data obtained in the lung adenoma bioassay suggest that Crude Shale Oil has tumorigenic potential. Paraho shale oil is carcinogenic in mouse skin. Hydrotreatment reduces but does not eliminate skin carcinogenicity and appreciable carcinogenic activity remains in the residue material. Kidney injury was noted following chronic dermal exposure to shale and petroleum derived middle distillates.

  13. New Albany shale group of Illinois

    Energy Technology Data Exchange (ETDEWEB)

    Cluff, R.M.; Reinbold, M.L.; Lineback, J.A.

    1981-01-01

    The Illinois basin's New Albany shale group consists of nine formations, with the brownish-black laminated shales being the predominant lithology in southeastern Illinois and nearby parts of Kentucky where the group reaches its maximum thickness of 460 ft. A second depositional center lies in west-central Illinois and southeastern Iowa, where the group is about 300 ft thick and the predominant lithology is bioturbated olive-gray to greenish-gray shale. A northeast-trending area of thin strata (mostly interfingering gray and black shales) separates these two depocenters. The distribution and types of lithofacies in the New Albany suggest that the shale was deposited across a shelf-slope-basin transition in a marine, stratified anoxic basin. The record of depositional events in the shale group could serve as a baseline for interpreting the history of tectonically more complex sequences such as the Appalachian basin's Devonian shales.

  14. Developing a shale heterogeneity index to predict fracture response in the Mancos Shale

    Science.gov (United States)

    DeReuil, Aubry; Birgenheier, Lauren; McLennan, John

    2017-04-01

    approximately equivalent proportions of Al-Ca-Si compositions, while Al-rich samples have consistently low strength. Moisture preserved samples fail on average at approximately 5 MPa lower than dry samples of similar facies. Additionally, moisture preserved samples fail in a step-like pattern when tested perpendicular to bedding. Tensile fractures are halted at heterogeneities and propagate parallel to bedding planes before developing a through-going failure plane, as opposed to the discrete, continuous fractures that crosscut dry samples. This result suggests that sedimentary heterogeneity plays a greater role in fracture propagation in moisture preserved samples, which are more indicative of in-situ reservoir conditions. Stress-strain curves will be further analyzed, including estimation of an energy released term based on post-failure response, and an estimation of volume of cracking measure on the physical fracture surface.

  15. In Situ Cardiovascular Tissue Engineering

    NARCIS (Netherlands)

    Talacua, H

    2016-01-01

    In this thesis, the feasibility of in situ TE for vascular and valvular purposes were tested with the use of different materials, and animal models. First, the feasibility of a decellularized biological scaffold (pSIS-ECM) as pulmonary heart valve prosthesis is examined in sheep (Chapter 2). Next,

  16. Lobular Carcinoma In Situ (LCIS)

    Science.gov (United States)

    ... consider treatments to reduce your risk of developing invasive breast cancer. Symptoms Lobular carcinoma in situ (LCIS) doesn't cause signs or ... tamoxifen vs raloxifene on the risk of developing invasive breast cancer and other disease outcomes: The NSABP study of tamoxifen and ... & treatment Advertisement ...

  17. Sex in situ, Teater Nordkraft

    DEFF Research Database (Denmark)

    Krøgholt, Ida

    2017-01-01

    Sex er en del af vores sociale praksis og centralt for det, vi hver især er. Men bortset fra pornoindustrien, har vi ikke mange muligheder for at få adgang til billeder af sex. Teater Nordkrafts forestilling Sex in situ vil gøre seksuelle billeder til noget, der kan deles, udveksles og tales om, og...

  18. Harnessing mineral carbonation reactions to seal fractured shales and sequester carbon

    Science.gov (United States)

    Clarens, A. F.; Tao, Z.

    2014-12-01

    Shale oil and gas are being developed widely in the United States despite the potential for long-term climate impacts driven by burning these new hydrocarbon resources and by fugitive emissions from fractured formations. Here the carbonation of calcium-based silicates is studied as a method to re-seal fractured shale formations and to store significant amounts of CO2 after hydrocarbon extraction. Ex situ mineral carbonation has been studied extensively for trapping CO2 from power plants but the application of these reactions directly within shale matrix under in situ conditions to seal shales and sequester carbon has not been studied. The reaction requires the solid calcium-based silicates being present within the shale fracture matrix and flooded with high-pressure CO2. The pressure and temperature within most shale formations would enable this carbonation reaction to precipitate solid calcium carbonate, which would clog fractures. Silicates could be injected in the same way that proppants are injected into shale gas wells. Wollastonite was tested here but other silicate minerals such as olivine could also be used in much the same way. To prove this concept, batch experiments were carried out under reservoir conditions representative of the Marcellus Shale in the presence of ground shale particles (39-177μm) and CaSiO3 powder. X-ray diffraction (XRD) patterns revealed the conversion of CaSiO3 into CaCO3 after 24 hours. Quantitative XRD analysis was used to determine that the conversion ratio of CaSiO3 was ~55% at 3100 Psi and 75oC. The reaction was sensitive to both temperature and pressure with ~58% conversion at an increased temperature of 95oC and only ~50% at lower pressure (2200psi). The morphology observed by Scanning Electron Microscopy (SEM) reveals that the shale particle surfaces are covered with precipitated calcite crystals ranging in size from 1 to 5 μm. Using energy-dispersive X-ray spectroscopy (EDS), the locations of residual CaSiO3and

  19. A Novel Energy-Efficient Pyrolysis Process: Self-pyrolysis of Oil Shale Triggered by Topochemical Heat in a Horizontal Fixed Bed

    Science.gov (United States)

    Sun, You-Hong; Bai, Feng-Tian; Lü, Xiao-Shu; Li, Qiang; Liu, Yu-Min; Guo, Ming-Yi; Guo, Wei; Liu, Bao-Chang

    2015-01-01

    This paper proposes a novel energy-efficient oil shale pyrolysis process triggered by a topochemical reaction that can be applied in horizontal oil shale formations. The process starts by feeding preheated air to oil shale to initiate a topochemical reaction and the onset of self-pyrolysis. As the temperature in the virgin oil shale increases (to 250–300°C), the hot air can be replaced by ambient-temperature air, allowing heat to be released by internal topochemical reactions to complete the pyrolysis. The propagation of fronts formed in this process, the temperature evolution, and the reaction mechanism of oil shale pyrolysis in porous media are discussed and compared with those in a traditional oxygen-free process. The results show that the self-pyrolysis of oil shale can be achieved with the proposed method without any need for external heat. The results also verify that fractured oil shale may be more suitable for underground retorting. Moreover, the gas and liquid products from this method were characterised, and a highly instrumented experimental device designed specifically for this process is described. This study can serve as a reference for new ideas on oil shale in situ pyrolysis processes. PMID:25656294

  20. Oil shale, shale oil, shale gas and non-conventional hydrocarbons

    Science.gov (United States)

    Clerici, A.; Alimonti, G.

    2015-08-01

    In recent years there has been a world "revolution" in the field of unconventional hydrocarbon reserves, which goes by the name of "shale gas", gas contained inside clay sediments micropores. Shale gas finds particular development in the United States, which are now independent of imports and see a price reduction to less than one third of that in Europe. With the high oil prices, in addition to the non-conventional gas also "oil shales" (fine-grained sedimentary rocks that contain a large amount of organic material to be used both to be directly burned or to extract liquid fuels which go under the name of shale oil), extra heavy oils and bitumen are becoming an industrial reality. Both unconventional gas and oil reserves far exceed in the world the conventional oil and gas reserves, subverting the theory of fossil fuels scarcity. Values and location of these new fossil reserves in different countries and their production by comparison with conventional resources are presented. In view of the clear advantages of unconventional fossil resources, the potential environmental risks associated with their extraction and processing are also highlighted.

  1. The role of water in unconventional in situ energy resource extraction technologies: Chapter 7 in Food, energy, and water: The chemistry connection

    Science.gov (United States)

    Gallegos, Tanya J.; Bern, Carleton R.; Birdwell, Justin E.; Haines, Seth S.; Engle, Mark A.

    2015-01-01

    Global trends toward developing new energy resources from lower grade, larger tonnage deposits that are not generally accessible using “conventional” extraction methods involve variations of subsurface in situ extraction techniques including in situ oil-shale retorting, hydraulic fracturing of petroleum reservoirs, and in situ recovery (ISR) of uranium. Although these methods are economically feasible and perhaps result in a smaller above-ground land-use footprint, there remain uncertainties regarding potential subsurface impacts to groundwater. This chapter provides an overview of the role of water in these technologies and the opportunities and challenges for water reuse and recycling.

  2. Shale play politics: the intergovernmental Odyssey of American shale governance.

    Science.gov (United States)

    Rabe, Barry G

    2014-01-01

    Intergovernmental responsibility for policy development for shale gas is concentrated primarily at the state level, given multiple statutory and political constraints on potential federal engagement. This opens the question of how a large subset of American states might craft shale policies, amid competing scholarly views on the commitment of states to environmental protection when energy development opportunities arise in the absence of applicable federal authority. The article examines recent trends in state political economy that may shape policy development and capacity, considers the heterogeneous pattern of policy emerging thus far, and draws preliminary lessons from the very small set of states that have enacted far-reaching new state legislation. It also offers early discussion of cross-border issues that may trigger multistate, regional, or ultimately federal engagement as well as growing signs of volatility in policy development in some states.

  3. Estimation of in-situ joint properties, Naesliden Mine

    Energy Technology Data Exchange (ETDEWEB)

    Barton, N.

    1980-05-15

    Finite element modelling of jointed rock masses requires detailed input data concerning the mechanical behaviour of the relevant joint sets. In the case of the Naesliden project, the properties of the footwall and hanging wall contacts were of particular concern because of their planarity. Methods of estimating the full-scale shear strength and shear stiffness are summarized. The estimates are based on assessment of full-scale values of the joint roughness coefficient (JRC), the joint wall compressive strength (JCS) and the residual friction angle. Sensitivity analyses indicate which of these parameters need to be determined with greatest accuracy at the levels of normal stress of interest. The full-scale estimates are compared with laboratory scale data and with data obtained from small scale tilt tests and tests on model tension fractures. A scale effect makes direct application of laboratory data of doubtful value. A simple dimensionless shear force-displacement formulation is suggested that describes the mobilization and subsequent reduction of joint roughness, as peak strength is exceeded during a given shearing event. The effect of changing normal stress during shearing is accounted for using this method.

  4. Regional Geologic Evaluations for Disposal of HLW and SNF: The Pierre Shale of the Northern Great Plains

    Energy Technology Data Exchange (ETDEWEB)

    Perry, Frank Vinton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kelley, Richard E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-09-14

    The DOE Spent Fuel and Waste Technology (SWFT) R&D Campaign is supporting research on crystalline rock, shale (argillite) and salt as potential host rocks for disposal of HLW and SNF in a mined geologic repository. The distribution of these three potential repository host rocks is limited to specific regions of the US and to different geologic and hydrologic environments (Perry et al., 2014), many of which may be technically suitable as a site for mined geologic disposal. This report documents a regional geologic evaluation of the Pierre Shale, as an example of evaluating a potentially suitable shale for siting a geologic HLW repository. This report follows a similar report competed in 2016 on a regional evaluation of crystalline rock that focused on the Superior Province of the north-central US (Perry et al., 2016).

  5. Modeling fluid injection induced microseismicity in shales

    Science.gov (United States)

    Carcione, José M.; Currenti, Gilda; Johann, Lisa; Shapiro, Serge

    2018-02-01

    Hydraulic fracturing in shales generates a cloud of seismic—tensile and shear—events that can be used to evaluate the extent of the fracturing (event clouds) and obtain the hydraulic properties of the medium, such as the degree of anisotropy and the permeability. Firstly, we investigate the suitability of novel semi-analytical reference solutions for pore pressure evolution around a well after fluid injection in anisotropic media. To do so, we use cylindrical coordinates in the presence of a formation (a layer) and spherical coordinates for a homogeneous and unbounded medium. The involved differential equations are transformed to an isotropic diffusion equation by means of pseudo-spatial coordinates obtained from the spatial variables re-scaled by the permeability components. We consider pressure-dependent permeability components, which are independent of the spatial direction. The analytical solutions are compared to numerical solutions to verify their applicability. The comparison shows that the solutions are suitable for a limited permeability range and moderate to minor pressure dependences of the permeability. Once the pressure evolution around the well has been established, we can model the microseismic events. Induced seismicity by failure due to fluid injection in a porous rock depends on the properties of the hydraulic and elastic medium and in situ stress conditions. Here, we define a tensile threshold pressure above which there is tensile emission, while the shear threshold is obtained by using the octahedral stress criterion and the in situ rock properties and conditions. Subsequently, we generate event clouds for both cases and study the spatio-temporal features. The model considers anisotropic permeability and the results are spatially re-scaled to obtain an effective isotropic medium representation. For a 3D diffusion in spherical coordinates and exponential pressure dependence of the permeability, the results differ from those of the classical

  6. Polyolefin nanocomposites in situ polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Galland, Griselda Barrera; Fim, Fabiana de C.; Milani, Marceo A.; Silva, Silene P. da; Forest, Tadeu; Radaelli, Gislaine, E-mail: griselda.barrera@ufrgs.br [Universidade Federal do Rio Grande de Sul - UFRGS, Porto Alegre, RS (Brazil); Basso, Nara R.S. [Pontificia Universidade Catolica do Rio Grande do Sul, Porto Alegre, RS (Brazil); Quijada, Raul [Universidad de Chile, Santiago (Chile)

    2011-07-01

    Polyethylene and polypropylene nanocomposites using grapheme nanosheets and treated chrysotile have been synthesized by in situ polymerization using metallocene catalysts. The fillers have been submitted to acid, thermal and/ou ultrasound treatments before to introduce them into the polymerization reactor. A complete characterization of the fillers has been done. The nanocomposites have been characterized by SEM, TEM, DRX and AFM. The thermal, mechanic -dynamic, mechanical and electrical properties of the nanocomposites are discussed. (author)

  7. Shale Oil Value Enhancement Research

    Energy Technology Data Exchange (ETDEWEB)

    James W. Bunger

    2006-11-30

    Raw kerogen oil is rich in heteroatom-containing compounds. Heteroatoms, N, S & O, are undesirable as components of a refinery feedstock, but are the basis for product value in agrochemicals, pharmaceuticals, surfactants, solvents, polymers, and a host of industrial materials. An economically viable, technologically feasible process scheme was developed in this research that promises to enhance the economics of oil shale development, both in the US and elsewhere in the world, in particular Estonia. Products will compete in existing markets for products now manufactured by costly synthesis routes. A premium petroleum refinery feedstock is also produced. The technology is now ready for pilot plant engineering studies and is likely to play an important role in developing a US oil shale industry.

  8. Oldest biliary endoprosthesis in situ.

    Science.gov (United States)

    Consolo, Pierluigi; Scalisi, Giuseppe; Crinò, Stefano F; Tortora, Andrea; Giacobbe, Giuseppa; Cintolo, Marcello; Familiari, Luigi; Pallio, Socrate

    2013-07-16

    The advantages of endoscopic retrograde cholangiopancreatography over open surgery have made it the predominant method of treating patients with choledocholithiasis. After sphincterotomy, however, 10%-15% of common bile duct stones cannot be removed with a basket or balloon. The methods for managing "irretrievable stones" include surgery, mechanical lithotripsy, intraductal or extracorporeal shock wave lithotripsy and biliary stenting. The case presented was a referred 82-year-old Caucasian woman with a 7-year-old plastic biliary endoprosthesis in situ. To the best of our knowledge the examined endoprosthesis is the oldest endoprosthesis in situ reported in the literature. Endoscopic biliary endoprosthesis placement remains a simple and safe procedure for patients with stones that are difficult to manage by conventional endoscopic methods and for patients who are unfit for surgery or who are high surgical risks. To date no consensus has been reached regarding how long a biliary prosthesis should remain in situ. Long-term biliary stenting may have a role in selected elderly patients if stones extraction has failed because the procedure may prevent stones impaction and cholangitis.

  9. Oldest biliary endoprosthesis in situ

    Science.gov (United States)

    Consolo, Pierluigi; Scalisi, Giuseppe; Crinò, Stefano F; Tortora, Andrea; Giacobbe, Giuseppa; Cintolo, Marcello; Familiari, Luigi; Pallio, Socrate

    2013-01-01

    The advantages of endoscopic retrograde cholangiopancreatography over open surgery have made it the predominant method of treating patients with choledocholithiasis. After sphincterotomy, however, 10%-15% of common bile duct stones cannot be removed with a basket or balloon. The methods for managing “irretrievable stones” include surgery, mechanical lithotripsy, intraductal or extracorporeal shock wave lithotripsy and biliary stenting. The case presented was a referred 82-year-old Caucasian woman with a 7-year-old plastic biliary endoprosthesis in situ. To the best of our knowledge the examined endoprosthesis is the oldest endoprosthesis in situ reported in the literature. Endoscopic biliary endoprosthesis placement remains a simple and safe procedure for patients with stones that are difficult to manage by conventional endoscopic methods and for patients who are unfit for surgery or who are high surgical risks. To date no consensus has been reached regarding how long a biliary prosthesis should remain in situ. Long-term biliary stenting may have a role in selected elderly patients if stones extraction has failed because the procedure may prevent stones impaction and cholangitis. PMID:23858381

  10. Spatially Resolved, In Situ Carbon Isotope Analysis of Archean Organic Matter

    Science.gov (United States)

    Williford, Kenneth H.; Ushikubo, Takayuki; Lepot, Kevin; Hallmann, Christian; Spicuzza, Michael J.; Eigenbrode, Jennifer L.; Summons, Roger E.; Valley, John W.

    2011-01-01

    Spatiotemporal variability in the carbon isotope composition of sedimentary organic matter (OM) preserves information about the evolution of the biosphere and of the exogenic carbon cycle as a whole. Primary compositions, and imprints of the post-depositional processes that obscure them, exist at the scale of individual sedimentary grains (mm to micron). Secondary ion mass spectrometry (SIMS) (1) enables analysis at these scales and in petrographic context, (2) permits morphological and compositional characterization of the analyte and associated minerals prior to isotopic analysis, and (3) reveals patterns of variability homogenized by bulk techniques. Here we present new methods for in situ organic carbon isotope analysis with sub-permil precision and spatial resolution to 1 micron using SIMS, as well as new data acquired from a suite of Archean rocks. Three analytical protocols were developed for the CAMECA ims1280 at WiscSIMS to analyze domains of varying size and carbon concentration. Average reproducibility (at 2SD) using a 6 micron spot size with two Faraday cup detectors was 0.4 %, and 0.8 % for analyses using 1 micron and 3 micron spot sizes with a Faraday cup (for C-12) and an electron multiplier (for C-13). Eight coals, two ambers, a shungite, and a graphite were evaluated for micron-scale isotopic heterogeneity, and LCNN anthracite (delta C-13 = -23.56 +/- 0.1 %, 2SD) was chosen as the working standard. Correlation between instrumental bias and H/C was observed and calibrated for each analytical session using organic materials with H/C between 0.1 and 1.5 (atomic), allowing a correction based upon a C-13H/C-13 measurement included in every analysis. Matrix effects of variable C/SiO2 were evaluated by measuring mm to sub-micron graphite domains in quartzite from Bogala mine, Sri Lanka. Apparent instrumental bias and C-12 count rate are correlated in this case, but this may be related to a crystal orientation effect in graphite. Analyses of amorphous

  11. Four Models of In Situ Simulation

    DEFF Research Database (Denmark)

    Musaeus, Peter; Krogh, Kristian; Paltved, Charlotte

    2014-01-01

    that there are four fruitful approaches to in situ simulation: (1) In situ simulation informed by reported critical incidents and adverse events from emergency departments (ED) in which team training is about to be conducted to write scenarios. (2) In situ simulation through ethnographic studies at the ED. (3) Using...... and relevance Empirical and theoretical research is needed to develop in situ simulation and to theorize and experiment with how we best take reported critical incidents and adverse events back to the clinic. In situ simulation offers a unique way to study team interactions there are widely different approaches......Introduction In situ simulation is characterized by being situated in the clinical environment as opposed to the simulation laboratory. But in situ simulation bears a family resemblance to other types of on the job training. We explore a typology of in situ simulation and suggest...

  12. Proof-of-Concept Oil Shale Facility Environmental Analysis Program

    Energy Technology Data Exchange (ETDEWEB)

    1990-11-01

    The objectives of the Project are to demonstrate: (1) the Modified In- Situ (MIS) shale oil extraction process and (2) the application of CFBC technology using oil shale, coal and waste gas streams as fuels. The project will focus on evaluating and improving the efficiency and environmental performance of these technologies. The project will be modest by commercial standards. A 17-retort MIS system is planned in which two retorts will be processed simultaneously. Production of 1206-barrels per calendar day of raw shale oil and 46-megawatts of electricity is anticipated. West Virginia University coordinated an Environmental Analysis Program for the Project. Experts from around the country were retained by WVU to prepare individual sections of the report. These experts were exposed to all of OOSI's archives and toured Tract C-b and Logan Wash. Their findings were incorporated into this report. In summary, no environmental obstacles were revealed that would preclude proceeding with the Project. One of the most important objectives of the Project was to verify the environmental acceptability of the technologies being employed. Consequently, special attention will be given to monitoring environmental factors and providing state of the art mitigation measures. Extensive environmental and socioeconomic background information has been compiled for the Tract over the last 15 years and permits were obtained for the large scale operations contemplated in the late 1970's and early 1980's. Those permits have been reviewed and are being modified so that all required permits can be obtained in a timely manner.

  13. Data set for Journal article "The shale gas revolution: barriers, sustainability, and emerging opportunities"

    Energy Technology Data Exchange (ETDEWEB)

    Middleton, Richard Stephen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-04

    Shale gas and hydraulic refracturing has revolutionized the US energy sector in terms of prices, consumption, and CO2 emissions. However, key questions remain including environmental concerns and extraction efficiencies that are leveling off. For the first time, we identify key discoveries, lessons learned, and recommendations from this shale gas revolution through extensive data mining and analysis of 23 years of production from 20,000 wells. Discoveries include identification of a learning-bydoing process where disruptive technology innovation led to a doubling in shale gas extraction, how refracturing with emerging technologies can transform existing wells, and how overall shale gas production is actually dominated by long-term tail production rather than the high-profile initial exponentially-declining production in the first 12 months. We hypothesize that tail production can be manipulated, through better fracturing techniques and alternative working fluids such as CO2, to increase shale gas recovery and minimize environmental impacts such as through carbon sequestration.

  14. The Art of in situ Cryocrystallization

    Indian Academy of Sciences (India)

    IAS Admin

    The Art of in situ Cryocrystallization. Dhananjay Dey and Deepak Chopra. Keywords. In situ cryocrystallization, states of matter, OHCD. The molecular and crystal structure of low-melting organic compounds and molecular liquids can be determined by in situ cryocrystallization technique. This also enables a detailed.

  15. Noise canceling in-situ detection

    Science.gov (United States)

    Walsh, David O.

    2014-08-26

    Technologies applicable to noise canceling in-situ NMR detection and imaging are disclosed. An example noise canceling in-situ NMR detection apparatus may comprise one or more of a static magnetic field generator, an alternating magnetic field generator, an in-situ NMR detection device, an auxiliary noise detection device, and a computer.

  16. A perspective on Canadian shale gas

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Mike; Davidson, Jim; Mortensen, Paul

    2010-09-15

    In a relatively new development over just the past few years, shale formations are being targeted for natural gas production. Based on initial results, there may be significant potential for shale gas in various regions of Canada, not only in traditional areas of conventional production but also non-traditional areas. However, there is much uncertainty because most Canadian shale gas production is currently in experimental or early developmental stages. Thus, its full potential will not be known for some time. If exploitation proves to be successful, Canadian shale gas may partially offset projected long-term declines in Canadian conventional natural gas production.

  17. Oil shale, shale oil, shale gas and non-conventional hydrocarbons

    Directory of Open Access Journals (Sweden)

    Clerici A.

    2015-01-01

    Full Text Available In recent years there has been a world “revolution” in the field of unconventional hydrocarbon reserves, which goes by the name of “shale gas”, gas contained inside clay sediments micropores. Shale gas finds particular development in the United States, which are now independent of imports and see a price reduction to less than one third of that in Europe. With the high oil prices, in addition to the non-conventional gas also “oil shales” (fine-grained sedimentary rocks that contain a large amount of organic material to be used both to be directly burned or to extract liquid fuels which go under the name of shale oil, extra heavy oils and bitumen are becoming an industrial reality. Both unconventional gas and oil reserves far exceed in the world the conventional oil and gas reserves, subverting the theory of fossil fuels scarcity. Values and location of these new fossil reserves in different countries and their production by comparison with conventional resources are presented. In view of the clear advantages of unconventional fossil resources, the potential environmental risks associated with their extraction and processing are also highlighted.

  18. In situ bypass og diabetes

    DEFF Research Database (Denmark)

    Jensen, Leif Panduro; Schroeder, T V; Lorentzen, J E

    1993-01-01

    From 1986 through to 1990 a total of 483 in situ bypass procedures were performed in 444 patients. Preoperative risk-factors were equally distributed among diabetic (DM) and non-diabetic (NDM) patients, except for smoking habits (DM:48%, NDM:64%, p = 0.002) and cardiac disease (DM:45%, NDM:29%, p...... decreased survival rate was found in diabetics (p bypass technique very useful in the treatment of critical ischaemia of the lower limb in diabetic patients. The overall results in diabetic patients, whether insulin-dependent or not, were equal to those in non...

  19. In situ dehydration of yugawaralite

    DEFF Research Database (Denmark)

    Artioli, G.; Ståhl, Kenny; Cruciani, G.

    2001-01-01

    The structural response of the natural zeolite yugawaralite (CaAl2Si6O16. 4H(2)O) upon thermally induced dehydration has been studied by Rietveld analysis of temperature-resolved powder diffraction data collected in situ in the temperature range 315-791 K using synchrotron radiation. The room...... of the cell parameters in the measured temperature range. This model involves a sixfold coordination of the Ca cations (five framework O atoms and one water molecule). There is no indication of significant structure changes before collapse, likely occurring when the last water molecule is expelled from...

  20. Understanding the True Stimulated Reservoir Volume in Shale Reservoirs

    KAUST Repository

    Hussain, Maaruf

    2017-06-06

    Successful exploitation of shale reservoirs largely depends on the effectiveness of hydraulic fracturing stimulation program. Favorable results have been attributed to intersection and reactivation of pre-existing fractures by hydraulically-induced fractures that connect the wellbore to a larger fracture surface area within the reservoir rock volume. Thus, accurate estimation of the stimulated reservoir volume (SRV) becomes critical for the reservoir performance simulation and production analysis. Micro-seismic events (MS) have been commonly used as a proxy to map out the SRV geometry, which could be erroneous because not all MS events are related to hydraulic fracture propagation. The case studies discussed here utilized a fully 3-D simulation approach to estimate the SRV. The simulation approach presented in this paper takes into account the real-time changes in the reservoir\\'s geomechanics as a function of fluid pressures. It is consisted of four separate coupled modules: geomechanics, hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive re-meshing. Reservoir stress condition, rock mechanical properties, and injected fluid pressure dictate how fracture elements could open or slide. Critical stress intensity factor was used as a fracture criterion governing the generation of new fractures or propagation of existing fractures and their directions. Our simulations were run on a Cray XC-40 HPC system. The studies outcomes proved the approach of using MS data as a proxy for SRV to be significantly flawed. Many of the observed stimulated natural fractures are stress related and very few that are closer to the injection field are connected. The situation is worsened in a highly laminated shale reservoir as the hydraulic fracture propagation is significantly hampered. High contrast in the in-situ stresses related strike-slip developed thereby shortens the extent of SRV. However, far field nature fractures that were not connected to

  1. Molecular characterization and comparison of shale oils generated by different pyrolysis methods

    Science.gov (United States)

    Birdwell, Justin E.; Jin, Jang Mi; Kim, Sunghwan

    2012-01-01

    Shale oils generated using different laboratory pyrolysis methods have been studied using standard oil characterization methods as well as Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) with electrospray ionization (ESI) and atmospheric photoionization (APPI) to assess differences in molecular composition. The pyrolysis oils were generated from samples of the Mahogany zone oil shale of the Eocene Green River Formation collected from outcrops in the Piceance Basin, Colorado, using three pyrolysis systems under conditions relevant to surface and in situ retorting approaches. Significant variations were observed in the shale oils, particularly the degree of conjugation of the constituent molecules and the distribution of nitrogen-containing compound classes. Comparison of FT-ICR MS results to other oil characteristics, such as specific gravity; saturate, aromatic, resin, asphaltene (SARA) distribution; and carbon number distribution determined by gas chromatography, indicated correspondence between higher average double bond equivalence (DBE) values and increasing asphaltene content. The results show that, based on the shale oil DBE distributions, highly conjugated species are enriched in samples produced under low pressure, high temperature conditions, and under high pressure, moderate temperature conditions in the presence of water. We also report, for the first time in any petroleum-like substance, the presence of N4 class compounds based on FT-ICR MS data. Using double bond equivalence and carbon number distributions, structures for the N4 class and other nitrogen-containing compounds are proposed.

  2. Cancer statistics: Breast cancer in situ.

    Science.gov (United States)

    Ward, Elizabeth M; DeSantis, Carol E; Lin, Chun Chieh; Kramer, Joan L; Jemal, Ahmedin; Kohler, Betsy; Brawley, Otis W; Gansler, Ted

    2015-01-01

    An estimated 60,290 new cases of breast carcinoma in situ are expected to be diagnosed in 2015, and approximately 1 in 33 women is likely to receive an in situ breast cancer diagnosis in her lifetime. Although in situ breast cancers are relatively common, their clinical significance and optimal treatment are topics of uncertainty and concern for both patients and clinicians. In this article, the American Cancer Society provides information about occurrence and treatment patterns for the 2 major subtypes of in situ breast cancer in the United States-ductal carcinoma in situ and lobular carcinoma in situ-using data from the North American Association of Central Cancer Registries and the 13 oldest Surveillance, Epidemiology, and End Results registries. The authors also present an overview of in situ breast cancer detection, treatment, risk factors, and prevention and discuss research needs and initiatives. © 2015 American Cancer Society.

  3. Compaction Characteristics of Igumale Shale | Iorliam | Global ...

    African Journals Online (AJOL)

    This paper reports the outcome of an investigation into the effect of different compactive energies on the compaction characteristics of Igumale shale, to ascertain its suitability as fill material in highway construction. Tests were conducted on specimen of Igumale shale, which included classification, compaction using three ...

  4. Introduction to special section: China shale gas and shale oil plays

    Science.gov (United States)

    Jiang, Shu; Zeng, Hongliu; Zhang, Jinchuan; Fishman, Neil; Bai, Baojun; Xiao, Xianming; Zhang, Tongwei; Ellis, Geoffrey S.; Li, Xinjing; Richards-McClung, Bryony; Cai, Dongsheng; Ma, Yongsheng

    2015-01-01

    In the last 10 years, the success of shale gas and shale oil productions as a result of technological advances in horizontal drilling, hydraulic fracturing and nanoscale reservoir characterization have revolutionized the energy landscape in the United States. Resource assessment by the China Ministry of Land and Resources in 2010 and 2012 and by the U.S. Energy Information Administration in 2011 and 2013 indicates China’s shale gas resource is the largest in the world and shale oil resource in China is also potentially significant. Inspired by the success in the United States, China looks forward to replicating the U.S. experience to produce shale gas to power its economy and reduce greenhouse gas emissions. By 2014, China had drilled 400 wells targeting marine, lacustrine, and coastal swamp transitional shales spanning in age from the Precambrian to Cenozoic in the last five years. So far, China is the leading country outside of North America in the viable production of shale gas, with very promising prospects for shale gas and shale oil development, from the Lower Silurian Longmaxi marine shale in Fuling in the southeastern Sichuan Basin. Geological investigations by government and academic institutions as well as exploration and production activities from industry indicate that the tectonic framework, depositional settings, and geomechanical properties of most of the Chinese shales are more complex than many of the producing marine shales in the United States. These differences limit the applicability of geologic analogues from North America for use in Chinese shale oil and gas resource assessments, exploration strategies, reservoir characterization, and determination of optimal hydraulic fracturing techniques. Understanding the unique features of the geology, shale oil and gas resource potential, and reservoir characteristics is crucial for sweet spot identification, hydraulic fracturing optimization, and reservoir performance prediction.

  5. Search for underground openings for in situ test facilities in crystalline rock

    Energy Technology Data Exchange (ETDEWEB)

    Wollenberg, H.A.; Strisower, B.; Corrigan, D.J.; Graf, A.N.; O' Brien, M.T.; Pratt, H.; Board, M.; Hustrulid, W.

    1980-01-01

    With a few exceptions, crystalline rocks in this study were limited to plutonic rocks and medium to high-grade metamorphic rocks. Nearly 1700 underground mines, possibly occurring in crystalline rock, were initially identified. Application of criteria resulted in the identification of 60 potential sites. Within this number, 26 mines and 4 civil works were identified as having potential in that they fulfilled the criteria. Thirty other mines may have similar potential. Most of the mines identified are near the contact between a pluton and older sedimentary, volcanic and metamorphic rocks. However, some mines and the civil works are well within plutonic or metamorphic rock masses. Civil works, notably underground galleries associated with pumped storage hydroelectric facilities, are generally located in tectonically stable regions, in relatively homogeneous crystalline rock bodies. A program is recommended which would identify one or more sites where a concordance exists between geologic setting, company amenability, accessibility and facilities to conduct in situ tests in crystalline rock.

  6. Different Methods of Predicting Permeability in Shale

    DEFF Research Database (Denmark)

    Mbia, Ernest Ncha; Fabricius, Ida Lykke; Krogsbøll, Anette

    Permeability is often very difficult to measure or predict in shale lithology. In this work we are determining shale permeability from consolidation tests data using Wissa et al., (1971) approach and comparing the results with predicted permeability from Kozeny’s model. Core and cuttings materials...... in shale useful in assessing their integrity for CO2 storage, gas shale exploitation and other engineering applications....... were obtained from Fjerritslev shale Formation in Juassic interval of Stenlille and Vedsted on-shore wells of Danish basin. The calculated permeability from specific surface and porosity vary from 0.09 to 48.53 μD while that calculated from consolidation tests data vary from 1000 μD at a low vertical...

  7. Intelligent fracture creation for shale gas development

    KAUST Repository

    Douglas, Craig C.

    2011-05-14

    Shale gas represents a major fraction of the proven reserves of natural gas in the United States and a collection of other countries. Higher gas prices and the need for cleaner fuels provides motivation for commercializing shale gas deposits even though the cost is substantially higher than traditional gas deposits. Recent advances in horizontal drilling and multistage hydraulic fracturing, which dramatically lower costs of developing shale gas fields, are key to renewed interest in shale gas deposits. Hydraulically induced fractures are quite complex in shale gas reservoirs. Massive, multistage, multiple cluster treatments lead to fractures that interact with existing fractures (whether natural or induced earlier). A dynamic approach to the fracturing process so that the resulting network of reservoirs is known during the drilling and fracturing process is economically enticing. The process needs to be automatic and done in faster than real-time in order to be useful to the drilling crews.

  8. Tu gme 10: Efficiency of shaft sealing for co2 sequestration in coal mines

    OpenAIRE

    Bertrand, François; Charlier, Robert; Collin, Frédéric; Dieudonné, Anne-Catherine

    2015-01-01

    This work examined the efficiency of a shaft sealing system for the CO2 sequestration in abandoned coal mines. The particular case of the coal mine of Anderlues was considered. The performed simulation took into account the anisotropic behaviour of shale and the presence of coalbeds. Peer reviewed

  9. Longwall mining

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-14

    As part of EIA`s program to provide information on coal, this report, Longwall-Mining, describes longwall mining and compares it with other underground mining methods. Using data from EIA and private sector surveys, the report describes major changes in the geologic, technological, and operating characteristics of longwall mining over the past decade. Most important, the report shows how these changes led to dramatic improvements in longwall mining productivity. For readers interested in the history of longwall mining and greater detail on recent developments affecting longwall mining, the report includes a bibliography.

  10. In-Situ Wire Damage Detection System

    Science.gov (United States)

    Williams, Martha; Roberson, Luke; Tate, Lanetra; Smith, Trent; Gibson, Tracy; Medelius, Pedro; Jolley, Scott

    2012-01-01

    An In-Situ Wire Damage Detection System (ISWDDS) has been developed that is capable of detecting damage to a wire insulation, or a wire conductor, or to both. The system will allow for realtime, continuous monitoring of wiring health/integrity and reduce the number of false negatives and false positives while being smaller, lighter in weight, and more robust than current systems. The technology allows for improved safety and significant reduction in maintenance hours for aircraft, space vehicles, satellites, and other critical high-performance wiring systems for industries such as energy production and mining. The integrated ISWDDS is comprised of two main components: (1) a wire with an innermost core conductor, an inner insulation film, a conductive layer or inherently conductive polymer (ICP) covering the inner insulation film, an outermost insulation jacket; and (2) smart connectors and electronics capable of producing and detecting electronic signals, and a central processing unit (CPU) for data collection and analysis. The wire is constructed by applying the inner insulation films to the conductor, followed by the outer insulation jacket. The conductive layer or ICP is on the outer surface of the inner insulation film. One or more wires are connected to the CPU using the smart connectors, and up to 64 wires can be monitored in real-time. The ISWDDS uses time domain reflectometry for damage detection. A fast-risetime pulse is injected into either the core conductor or conductive layer and referenced against the other conductor, producing transmission line behavior. If either conductor is damaged, then the signal is reflected. By knowing the speed of propagation of the pulse, and the time it takes to reflect, one can calculate the distance to and location of the damage.

  11. In-situ measurement system

    Science.gov (United States)

    Lord, David E.

    1983-01-01

    A multipurpose in situ underground measurement system comprising a plurality of long electrical resistance elements in the form of rigid reinforcing bars, each having an open loop "hairpin" configuration of shorter length than the other resistance elements. The resistance elements are arranged in pairs in a unitized structure, and grouted in place in the underground volume. The electrical resistance of each element and the difference in electrical resistance of the paired elements are obtained, which difference values may be used in analytical methods involving resistance as a function of temperature. A scanner sequentially connects the resistance-measuring apparatus to each individual pair of elements. A source of heating current is also selectively connectable for heating the elements to an initial predetermined temperature prior to electrical resistance measurements when used as an anemometer.

  12. Prospects for the North America’ shale hydrocarbons development

    Directory of Open Access Journals (Sweden)

    Tatiana V. Polyakova

    2014-01-01

    Full Text Available An entire generation of American politicians were concerned about the growing U.S. dependence on imported oil and natural gas. However, in the last few years the situation has changed dramatically: there was started the development of not only the resources of shale gas, but shale oil. As a result in political and economic circles they began to talk about it as the most significant breakthrough in the energy resources development since the oil boom in Texas in the late 1920s. How large are these resources? What problems have to be overcome if the available potential will be realized? How will this problems affect the U.S. energy policy? Concerns about the adequacy of regulation, in particular the environmental issues associated with the non-conventional hydrocarbons production, have led to the internal public debate on the impact of unconventional oil and gas resources mining boom. One thing is clear: significant amounts of additional oil and gas supplies in the U.S. will have far-reaching political consequences for the world. The article presents the different points of view on the prospects for oil and gas production in North America, as well as on the political issues related to it.

  13. Area Strip Mine Reclamation Using Dredged Material: A Field Demonstration.

    Science.gov (United States)

    1980-07-01

    history of surface mining is essentially that of mining ) coal, copper, and iron ores, and nonmetallic minerals--clays, gypsum, rock phosphate, sand...undantShale P 16.0 in bottom 5-10 feet of formation A A- LaSalle P.2 coal -- ligh fireclay 40’ Coal /# 2 P -"" " 9.0 Ions" of pisol,tic z und~clay bulders

  14. Tridimensional modelling and resource estimation of the mining waste piles of São Domingos mine, Iberian Pyrite Belt, Portugal

    Science.gov (United States)

    Vieira, Alexandre; Matos, João; Lopes, Luis; Martins, Ruben

    2016-04-01

    Located in the Iberian Pyrite Belt (IPB) northern sector, near the Portuguese/Spanish border, the outcropping São Domingos deposit was mined since Roman time. Between 1854 and 1966 the Mason & Barry Company developed open pit excavation until 120 m depth and underground mining until 420 m depth. The São Domingos subvertical deposit is associated with felsic volcanics and black shales of the IPB Volcano-Sedimentary Complex and is represented by massive sulphide and stockwork ore (py, cpy, sph, ga, tt, aspy) and related supergene enrichment ore (hematite gossan and covellite/chalcocite). Different mine waste classes were mapped around the old open pit: gossan (W1), felsic volcanic and shales (W2), shales (W3) and mining waste landfill (W4). Using the LNEG (Portuguese Geological Survey) CONASA database (company historical mining waste characterization based on 162 shafts and 160 reverse circulation boreholes), a methodology for tridimensional modelling mining waste pile was followed, and a new mining waste resource is presented. Considering some constraints to waste removal, such as the Mina de São Domingos village proximity of the wastes, the industrial and archaeological patrimony (e.g., mining infrastructures, roman galleries), different resource scenarios were considered: unconditioned resources (total estimates) and conditioned resources (only the volumes without removal constraints considered). Using block modelling (SURPAC software) a mineral inferred resource of 2.38 Mt @ 0.77 g/t Au and 8.26 g/t Ag is estimated in unconditioned volumes of waste. Considering all evaluated wastes, including village areas, an inferred resource of 4.0 Mt @ 0.64 g/t Au and 7.30 g/t Ag is presented, corresponding to a total metal content of 82,878 oz t Au and 955,753 oz t Ag. Keywords. São Domingos mine, mining waste resources, mining waste pile modelling, Iberian Pyrite Belt, Portugal

  15. Training for teamwork through in situ simulations

    Science.gov (United States)

    Sorensen, Asta; Poehlman, Jon; Bollenbacher, John; Riggan, Scott; Davis, Stan; Miller, Kristi; Ivester, Thomas; Kahwati, Leila

    2015-01-01

    In situ simulations allow healthcare teams to practice teamwork and communication as well as clinical management skills in a team's usual work setting with typically available resources and equipment. The purpose of this video is to demonstrate how to plan and conduct in situ simulation training sessions, with particular emphasis on how such training can be used to improve communication and teamwork. The video features an in situ simulation conducted at a labour and delivery unit in response to postpartum hemorrhage. PMID:26294962

  16. The SENSEI Generic In Situ Interface

    Energy Technology Data Exchange (ETDEWEB)

    Ayachit, Utkarsh [Kitware, Inc., Clifton Park, NY (United States); Whitlock, Brad [Intelligent Light, Rutherford, NJ (United States); Wolf, Matthew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Loring, Burlen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Geveci, Berk [Kitware, Inc., Clifton Park, NY (United States); Lonie, David [Kitware, Inc., Clifton Park, NY (United States); Bethel, E. Wes [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2017-04-11

    The SENSEI generic in situ interface is an API that promotes code portability and reusability. From the simulation view, a developer can instrument their code with the SENSEI API and then make make use of any number of in situ infrastructures. From the method view, a developer can write an in situ method using the SENSEI API, then expect it to run in any number of in situ infrastructures, or be invoked directly from a simulation code, with little or no modification. This paper presents the design principles underlying the SENSEI generic interface, along with some simplified coding examples.

  17. Geospatial assessment of invasive plants on reclaimed mines in Alabama

    Science.gov (United States)

    D. Lemke; C.J. Schweitzer; W. Tadesse; Y. Wang; J.A. Brown

    2013-01-01

    Throughout the world, the invasion of nonnative plants is an increasing threat to native biodiversity and ecosystem sustainability. Invasion is especially prevalent in areas affected by land transformation and disturbance. Surface mines are a major land transformation, and thus may promote the establishment and persistence of invasive plant communities. Using the Shale...

  18. Impacts and mitigations of in situ bitumen production from Alberta oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Edmunds, Neil

    2010-09-15

    85% or more of Alberta's oil sands is too deep to mine and will be recovered by in situ methods, i.e. from drill holes. This has been made commercially possible through the development in Alberta of Steam Assisted Gravity Drainage (SAGD). Does this impending development threaten the local ecosystem? A quantitative account is given of the principal impacts of in situ oil sands development in Alberta. Impacts on land (habitats), water, and air are considered in terms of local capacity, global benchmarks, and comparisons to alternative renewable technologies. Improvements due to new solvent-additive technology are highlighted.

  19. System for producing a uniform rubble bed for in situ processes

    Science.gov (United States)

    Galloway, T.R.

    1983-07-05

    A method and a cutter are disclosed for producing a large cavity filled with a uniform bed of rubblized oil shale or other material, for in situ processing. A raise drill head has a hollow body with a generally circular base and sloping upper surface. A hollow shaft extends from the hollow body. Cutter teeth are mounted on the upper surface of the body and relatively small holes are formed in the body between the cutter teeth. Relatively large peripheral flutes around the body allow material to drop below the drill head. A pilot hole is drilled into the oil shale deposit. The pilot hole is reamed into a large diameter hole by means of a large diameter raise drill head or cutter to produce a cavity filled with rubble. A flushing fluid, such as air, is circulated through the pilot hole during the reaming operation to remove fines through the raise drill, thereby removing sufficient material to create sufficient void space, and allowing the larger particles to fill the cavity and provide a uniform bed of rubblized oil shale. 4 figs.

  20. Carbon nanotubes (CNT) for enhanced oil production from shales

    OpenAIRE

    Hussain, Aqeel

    2014-01-01

    The shale gas production has brought a revolution in US energy market and the global prospect of shale gas production is on continuous increase. The advancements in hydraulic fracturing made it possible to extract very low permeability shale gas through fracturing the shale rock. The once fractured shale rock is kept open with the induction of spherical particles known as proppants. The performance of proppants is crucial for oil & gas production. Therefore, the prospect of applic...

  1. Mechanism for Burgess Shale-type preservation

    DEFF Research Database (Denmark)

    Gaines, Robert R.; Hammarlund, Emma U.; Hou, Xianguang

    2012-01-01

    soft-bodied fossil assemblages has remained enigmatic since Walcott's initial discovery in 1909. Here, we demonstrate the mechanism of Burgess Shale-type preservation using sedimentologic and geochemical data from the Chengjiang, Burgess Shale, and five other principal Burgess Shale-type deposits....... Sulfur isotope evidence from sedimentary pyrites reveals that the exquisite fossilization of organic remains as carbonaceous compressions resulted from early inhibition of microbial activity in the sediments by means of oxidant deprivation. Low sulfate concentrations in the global ocean and low...

  2. Method for retorting oil shale

    Science.gov (United States)

    Shang, Jer-Yu; Lui, A.P.

    1985-08-16

    The recovery of oil from oil shale is provided in a fluidized bed by using a fluidizing medium of a binary mixture of carbon dioxide and 5 steam. The mixture with a steam concentration in the range of about 20 to 75 volume percent steam provides an increase in oil yield over that achievable by using a fluidizing gas of carbon dioxide or steam alone when the mixture contains higher steam concentrations. The operating parameters for the fluidized bed retorted are essentially the same as those utilized with other gaseous fluidizing mediums with the significant gain being in the oil yield recovered which is attributable solely to the use of the binary mixture of carbon dioxide and steam. 2 figs.

  3. Micro mechanical study of shales

    Science.gov (United States)

    Bonnelye, Audrey; Picard, David; Gharbi, Hakim; Dimanov, Alexandre; Bornert, Michel; Conil, Nathalie

    2017-04-01

    In the following years, the French nuclear wastes will be buried in the underground repository in shales, that will be excavated at 490 m in depth, within the Callovo Oxfordian (Cox) argillaceous formation. The hydro-mechanical behavior of the argillaceous rock is complex, like the multiphase and multi-scale structured material itself. The argilaceous matrix is composed of interstratified Illite-Smectite particles, it contains detritic quartz and calcite, accessory pyrite, and the rock porosity ranges from micrometre to nanometre scales. Besides the bedding anisotropy, structural variabilities exist at all scales, from the decametric-metric scales of the geological formation to the respectively millimetric and micrometric scales of the aggregates of particles and clay particles Our study aims at understanding the complex mechanisms which are activated at the micro-scale and are involved in the macroscopic inelastic deformation of such a complex material.An experimental protocol was developed in order to perform uniaxial deformation experiment at controlled displacement rate, inside an environmental scanning electron microscope (ESEM), under controlled relative humidity, in order to preserve as much as possible the natural state of saturation of shales. Three sample orientations (90°, 45° and 0°) were used in order to characterize the mechanical anisotropy and the mechanisms involved in the deformation. The observed smple surfaces were polished by broad ion beam in order to reveal the fine microstructures of the argillaceous matrix. Digital images were acquired at different loading stages during the deformation process and Digital Image Correlation Technique (DIC) was applied in order to retrieve full strain fields at various scales from sample scale to microstructure scale. The analysis allows for identification of the active mechanisms, their relationships to the microstructure and their interactions.

  4. PRINS and in situ PCR protocols

    National Research Council Canada - National Science Library

    Gosden, John R

    1997-01-01

    ... mapping of DNA sequences on chromosomes and location of gene expression followed the invention and refinement of in situ hybridization. Among the most recent technical developments has been the use of oligonucleotide primers to detect and amplify or extend complementary sequences in situ, and it is to this novel field that PRINS and In S...

  5. In situ characterization technique for nanotribological investigations

    NARCIS (Netherlands)

    Deladi, S.; Berenschot, Johan W.; de Boer, Meint J.; Krijnen, Gijsbertus J.M.; Tas, Niels Roelof; Elwenspoek, Michael Curt

    An innovative technique has been developed to enable in situ monitoring of mechanical surface modification. The method is based on using a test surface and a sharp tip located on two different cantilevers; one for mechanical surface modification and the other for in situ detection of surface

  6. Developments in wireline in-situ rock stress measurement

    Energy Technology Data Exchange (ETDEWEB)

    Pedroso, Carlos [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Canas, Jesus A.; Holzberg, Bruno; Gmach, Helmut [Schlumberger Servicos de Petroleo Ltda., Rio de Janeiro, RJ (Brazil)

    2008-07-01

    This paper presents recent developments of in-situ stress measurements with wireline tools. The stress measurements are based on the micro hydraulic techniques that can be initialized when an interval is pressurized by pumping fluid until a tensile fracture begins or by packers fracturing (sleeve fracturing). Ultrasonic and Micro-resistivity borehole image logs (before and after the testes) are used as a complement, in order to observe the fractures created by the tests, evaluating the mechanical behavior of the formation. An offshore case study is presented, where shales and tight sandstones at depths deeper than 4500 meters depth were successfully evaluated. A workflow to succeed on stress measurements on such environments is proposed, what includes a planning phase: where breakdown pressures ranges are estimated and compared with the capacity of the tools, a Real Time Monitoring phase, where a decision tree is proposed to help on quick decisions while testing, and an interpretation phase, where appropriate techniques are indicated to evaluate the results. Also, the paper presents the main operational needs to succeed on such environments. Basically, such tests require an entirely software controlled, motorized and modular design tool consisting of dual packer (DP), pump out and flow control modules (Figure 1). These modules were upgraded for the present environment: conditions such as temperatures above 300 deg F, formation pressures above 10,000 psia, very low formation permeability, high pressure differential need and oil based mud (OBM) environment. (author)

  7. Chemically enhanced in situ recovery

    Energy Technology Data Exchange (ETDEWEB)

    Sale, T. [CH2M Hill, Denver, CO (United States); Pitts, M.; Wyatt, K. [Surtek, Inc., Golden, CO (United States)] [and others

    1996-08-01

    Chemically enhanced recovery is a promising alternative to current technologies for management of subsurface releases of organic liquids. Through the inclusion of surfactants, solvents, polymers, and/or alkaline agents to a waterflood, the transport of targeted organic compounds can be increased and rates of recovery enhanced. By far, the vast majority of work done in the field of chemically enhanced recovery has been at a laboratory scale. The following text focuses on chemically enhanced recovery from a field application perspective with emphasis given to chlorinated solvents in a low permeability setting. While chlorinated solvents are emphasized, issues discussed are also relevant to organic liquids less dense than water such as petroleum products. Topics reviewed include: (1) Description of technology; (2) General technology considerations; (3) Low permeability media considerations; (4) Cost and reliability considerations; (5) Commercial availability; and (6) Case histories. Through this paper an appreciation is developed of both the potential and limitations of chemically enhanced recovery. Excluded from the scope of this paper is the in situ destruction of organic compounds through processes such as chemical or biological oxidation, chemically enhanced recovery of inorganic compounds, and ex situ soil treatment processes. 11 refs., 2 figs., 1 tab.

  8. Enhanced in situ aerobic bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Sharfe, K. [CleanEARTH Solutions Ltd., Concord, ON (Canada)

    2007-07-01

    An enhanced in situ aerobic bioremediation process was described. The process used microbe supporting emulsifications to enhance bioavailability as well as to attenuate microbe competition and boost microbial production. Microbes were added prior to application and rapidly initiated bioremediation once applied to impacted areas. The microbe supporting emulsifiers were metabolically active. The study showed that exposed surface areas increased as hydrocarbon masses were divided, which in turn increased the water/substrate interface where microbial action occurred. Nutrients were used to ensure that crowding and waste accumulation were attenuated in order to ensure that the speed of growth and reproduction progressed exponentially. Water-carrying bacteria, enzymes and nutrients were adsorbed to the soil's particle surface and then diffused between particles. The sequestered hydrocarbons were then emulsified and removed in order to be bioremediated. It was concluded that biological catalysts were used to increase microbial activity and to trigger anabolic responses in microbes. Details of a biocatalyst laboratory solution analysis were also included. tabs., figs.

  9. Ecological risks of shale oil and gas development to wildlife, aquatic resources and their habitats.

    Science.gov (United States)

    Brittingham, Margaret C; Maloney, Kelly O; Farag, Aïda M; Harper, David D; Bowen, Zachary H

    2014-10-07

    Technological advances in hydraulic fracturing and horizontal drilling have led to the exploration and exploitation of shale oil and gas both nationally and internationally. Extensive development of shale resources has occurred within the United States over the past decade, yet full build out is not expected to occur for years. Moreover, countries across the globe have large shale resources and are beginning to explore extraction of these resources. Extraction of shale resources is a multistep process that includes site identification, well pad and infrastructure development, well drilling, high-volume hydraulic fracturing and production; each with its own propensity to affect associated ecosystems. Some potential effects, for example from well pad, road and pipeline development, will likely be similar to other anthropogenic activities like conventional gas drilling, land clearing, exurban and agricultural development and surface mining (e.g., habitat fragmentation and sedimentation). Therefore, we can use the large body of literature available on the ecological effects of these activities to estimate potential effects from shale development on nearby ecosystems. However, other effects, such as accidental release of wastewaters, are novel to the shale gas extraction process making it harder to predict potential outcomes. Here, we review current knowledge of the effects of high-volume hydraulic fracturing coupled with horizontal drilling on terrestrial and aquatic ecosystems in the contiguous United States, an area that includes 20 shale plays many of which have experienced extensive development over the past decade. We conclude that species and habitats most at risk are ones where there is an extensive overlap between a species range or habitat type and one of the shale plays (leading to high vulnerability) coupled with intrinsic characteristics such as limited range, small population size, specialized habitat requirements, and high sensitivity to disturbance

  10. Ecological risks of shale oil and gas development to wildlife, aquatic resources and their habitats

    Science.gov (United States)

    Brittingham, Margaret C.; Maloney, Kelly O.; Farag, Aïda M.; Harper, David D.; Bowen, Zachary H.

    2014-01-01

    Technological advances in hydraulic fracturing and horizontal drilling have led to the exploration and exploitation of shale oil and gas both nationally and internationally. Extensive development of shale resources has occurred within the United States over the past decade, yet full build out is not expected to occur for years. Moreover, countries across the globe have large shale resources and are beginning to explore extraction of these resources. Extraction of shale resources is a multistep process that includes site identification, well pad and infrastructure development, well drilling, high-volume hydraulic fracturing and production; each with its own propensity to affect associated ecosystems. Some potential effects, for example from well pad, road and pipeline development, will likely be similar to other anthropogenic activities like conventional gas drilling, land clearing, exurban and agricultural development and surface mining (e.g., habitat fragmentation and sedimentation). Therefore, we can use the large body of literature available on the ecological effects of these activities to estimate potential effects from shale development on nearby ecosystems. However, other effects, such as accidental release of wastewaters, are novel to the shale gas extraction process making it harder to predict potential outcomes. Here, we review current knowledge of the effects of high-volume hydraulic fracturing coupled with horizontal drilling on terrestrial and aquatic ecosystems in the contiguous United States, an area that includes 20 shale plays many of which have experienced extensive development over the past decade. We conclude that species and habitats most at risk are ones where there is an extensive overlap between a species range or habitat type and one of the shale plays (leading to high vulnerability) coupled with intrinsic characteristics such as limited range, small population size, specialized habitat requirements, and high sensitivity to disturbance

  11. GIS-and Web-based Water Resource Geospatial Infrastructure for Oil Shale Development

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Wei [Colorado School of Mines, Golden, CO (United States); Minnick, Matthew [Colorado School of Mines, Golden, CO (United States); Geza, Mengistu [Colorado School of Mines, Golden, CO (United States); Murray, Kyle [Colorado School of Mines, Golden, CO (United States); Mattson, Earl [Colorado School of Mines, Golden, CO (United States)

    2012-09-30

    The Colorado School of Mines (CSM) was awarded a grant by the National Energy Technology Laboratory (NETL), Department of Energy (DOE) to conduct a research project en- titled GIS- and Web-based Water Resource Geospatial Infrastructure for Oil Shale Development in October of 2008. The ultimate goal of this research project is to develop a water resource geo-spatial infrastructure that serves as “baseline data” for creating solutions on water resource management and for supporting decisions making on oil shale resource development. The project came to the end on September 30, 2012. This final project report will report the key findings from the project activity, major accomplishments, and expected impacts of the research. At meantime, the gamma version (also known as Version 4.0) of the geodatabase as well as other various deliverables stored on digital storage media will be send to the program manager at NETL, DOE via express mail. The key findings from the project activity include the quantitative spatial and temporal distribution of the water resource throughout the Piceance Basin, water consumption with respect to oil shale production, and data gaps identified. Major accomplishments of this project include the creation of a relational geodatabase, automated data processing scripts (Matlab) for database link with surface water and geological model, ArcGIS Model for hydrogeologic data processing for groundwater model input, a 3D geological model, surface water/groundwater models, energy resource development systems model, as well as a web-based geo-spatial infrastructure for data exploration, visualization and dissemination. This research will have broad impacts of the devel- opment of the oil shale resources in the US. The geodatabase provides a “baseline” data for fur- ther study of the oil shale development and identification of further data collection needs. The 3D geological model provides better understanding through data interpolation and

  12. Black shale studies in Kentucky. Quarterly report

    Energy Technology Data Exchange (ETDEWEB)

    1979-03-01

    This document presents a compilation of geochemical data for the eastern Kentucky outcrop belt. It also reports on data collection activities for the EGSP (Eastern Gas Shales Project) data bank. (DLC)

  13. Phase Equilibrium Modeling for Shale Production Simulation

    DEFF Research Database (Denmark)

    Sandoval Lemus, Diego Rolando

    simulator, which was then used to assess the impact of the capillary pressure on phase behavior in oil and gas production from tight reservoirs. Since capillary pressure and adsorption occur simultaneously in shale, its combined effect was studied. A model comparison for high-pressure adsorption in shale...... is presented. The adsorption data in shale is generally scarce, therefore, additional capabilities besides the accuracy were considered in the comparison. The multicomponent potential theory of adsorption yields the best results. Moreover, it shows to be useful to extrapolate adsorption data for hydrocarbons...... calculation tools for phase equilibrium in porous media with capillary pressure and adsorption effects. Analysis using these tools have shown that capillary pressure and adsorption have non-negligible effects on phase equilibrium in shale. As general tools, they can be used to calculate phase equilibrium...

  14. EVALUATION OF SHALE GAS POTENTIAL IN KAZAKHSTAN

    Directory of Open Access Journals (Sweden)

    Lidiya Parkhomchik

    2015-01-01

    Full Text Available The article considers the primary evaluation of the shale gas resource potential in Kazakhstan, as well as defines the most problematic issues for the large-scale shale gas production over the state. The authors pay special attention to the national strategy of the Kazakhstani government in the sphere of the unconventional energy sources production, defining the possible technological and environmental problems for the shale gas extraction. The article also notes that implementation of the fracking technologies in the country could cause both positive and negative effects on the economy of Kazakhstan. Therefore, further steps in this direction should be based on the meaningful and comprehensive geological data regarding the shale gas potential.

  15. In situ neoplasia in lymph node pathology.

    Science.gov (United States)

    Oishi, Naoki; Montes-Moreno, Santiago; Feldman, Andrew L

    2017-11-09

    In situ neoplasia represents the earliest form of malignant progression and is characterized by localization limited to the compartment corresponding to the cell of origin. Like other cancers, lymphoid neoplasms are considered to develop by multistep pathogenetic mechanisms. However, because of the circulating nature of lymphocytes, in situ lymphoid neoplasia may be difficult to identify histopathologically, and the compartment to which it is restricted may be physiological rather than strictly anatomical. The 2016 WHO classification of lymphoid neoplasms recognizes two in situ entities: in situ follicular neoplasia (ISFN) and in situ mantle cell neoplasia (ISMCN). This review summarizes the clinical features, histopathology, genetics, and differential diagnoses of these two entities, including distinction from both their overly malignant counterparts and a variety of reactive processes. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Important geological properties of unconventional resource shales

    Science.gov (United States)

    Slatt, Roger

    2011-12-01

    The revelation of vast global quantities of potentially productive gas and oil-prone shales has led to advancements in understanding important geological properties which impact reservoir performance. Based upon research on a variety of shales, several geological properties have been recognized as being common and important to hydrocarbon production. (1) transport/depositional processes include hemipelagic `rain', hyperpycnal flows, turbidity current flows, tempestites, wave-reworking, and contour currents in both shallow and deep water settings. (2) Common shale minerals include clays, quartz, calcite, dolomite, apatite, and pyrite; organic constituents include spores (Tasmanites), plant remains, biogenic quartz and calcite, and arenaceous foraminifera. (3) Porosity and permeability are characteristically low with pore sizes ranging down to the nanoscale. Main pore types include intergranular (including pores within clay floccules), porous organic matter, porous fecal pellets, and microfractures. (4) Important geochemical characteristics include organic richness (>3%), maturity (>1.1%Ro for shale gas and 0.6-0.9% for shale oil) and type (I-IV), in addition to certain biomarkers which are indicators of bottom water oxicity during deposition. Remaining hydrocarbon potential [RHP = (S1 + S2)/TOC] also reflects temporal environmental changes. `Isotopic reversals' can be used to detect best producing areas in shale-gas plays. (5) Lithofacies stacking patterns and sequence stratigraphy are the result of eustatic depositional history. A general sequence stratigraphic model is presented here that highlights this commonality. (6) Geomechanical properties are key to drilling, fracturing and production of hydrocarbons. Brittle-ductile couplets at several scales occur in shale sequences. (7) Geophysical properties, when calibrated to rock properties, provide a means of regionally to locally mapping the aforementioned properties. (8) Economic and societal considerations in the

  17. Bioremediation of Pit Lakes - Gilt Edge Mine

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) Region 8 Superfund Office and the EPA National Risk Management Research Laboratory (NRMRL) Mine Waste Technology Program (MWTP) conducted a field-scale treatability study demonstrating an in situ bio/geochemical treatment technology ...

  18. Legal Regime of Shale Gas Extraction

    OpenAIRE

    Ovidiu – Horia Maican

    2013-01-01

    Some countries with large reserves intend to promote shale gas production, in order to reduce their dependency on imported gas. Shale gas will be an important new aspect in the world energy scene, with many effects. European Union wants secure and affordable sources of energy. Natural gas is the cleanest fossil fuel and a vital component of European Union's energy strategy. One of the most important aspects is that gas produces significantly cleaner energy than other fossil fuels. From a lega...

  19. The influence of shale gas on steamcracking

    Energy Technology Data Exchange (ETDEWEB)

    Rupieper, A. [Linde Engineering Dresden GmbH, Dresden (Germany)

    2013-11-01

    US shale gas reserves with more than 860 TCF (Source: U.S. Energy Information Administration study World Shale Gas Resources) account for 2 of the global largest reserves after China. In 7 areas of the US, these reserves are systematically explored, providing a significant amount of cheap natural gas source for decades. The ethane share, carried by such shale gas, can reach up to 16%. Ethane has been already in the past 2 most important feedstock for Steamcrackers, being the backbone of the Petrochemical Industry. Due to availability of vast shale gas, the US steamcracker industry is facing a shift from naphtha to shale gas ethane, as the margin of Ethylene produced from shale gas ethane is significantly larger than that of naphtha based Ethylene (app. + 630 USD/t Ethylene). As a consequence shale gas is ''the magic bullet'' incinerating investments into Steamcrackers and downstream plants for U.S petrochemical industry. Steamcracker Projects with an additional ethylene production capacity of more than 17 million tons/a by 2020 are announced or already under construction. Investments into downstream plants refining the C2 derivatives will follow or are already in planning/engineering phase. But the US market cannot absorb all related products, causing a significant export exposure, which will influence global trade flows for C2 derivatives and affect prices. This article presents the impact of shale gas ethane cracking on: - Trade flow of C2 derivatives; - By-product deficits; - Alternate C3+ derivative production routes; - Challenges related to engineering requirements and project execution for Steamcracker projects. (orig.)

  20. Text Mining.

    Science.gov (United States)

    Trybula, Walter J.

    1999-01-01

    Reviews the state of research in text mining, focusing on newer developments. The intent is to describe the disparate investigations currently included under the term text mining and provide a cohesive structure for these efforts. A summary of research identifies key organizations responsible for pushing the development of text mining. A section…

  1. Environmental control costs for oil shale processes

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-10-01

    The studies reported herein are intended to provide more certainty regarding estimates of the costs of controlling environmental residuals from oil shale technologies being readied for commercial application. The need for this study was evident from earlier work conducted by the Office of Environment for the Department of Energy Oil Shale Commercialization Planning, Environmental Readiness Assessment in mid-1978. At that time there was little reliable information on the costs for controlling residuals and for safe handling of wastes from oil shale processes. The uncertainties in estimating costs of complying with yet-to-be-defined environmental standards and regulations for oil shale facilities are a critical element that will affect the decision on proceeding with shale oil production. Until the regulatory requirements are fully clarified and processes and controls are investigated and tested in units of larger size, it will not be possible to provide definitive answers to the cost question. Thus, the objective of this work was to establish ranges of possible control costs per barrel of shale oil produced, reflecting various regulatory, technical, and financing assumptions. Two separate reports make up the bulk of this document. One report, prepared by the Denver Research Institute, is a relatively rigorous engineering treatment of the subject, based on regulatory assumptions and technical judgements as to best available control technologies and practices. The other report examines the incremental cost effect of more conservative technical and financing alternatives. An overview section is included that synthesizes the products of the separate studies and addresses two variations to the assumptions.

  2. Assessment of undiscovered shale gas and shale oil resources in the Mississippian Barnett Shale, Bend Arch–Fort Worth Basin Province, North-Central Texas

    Science.gov (United States)

    Marra, Kristen R.; Charpentier, Ronald R.; Schenk, Christopher J.; Lewan, Michael D.; Leathers-Miller, Heidi M.; Klett, Timothy R.; Gaswirth, Stephanie B.; Le, Phuong A.; Mercier, Tracey J.; Pitman, Janet K.; Tennyson, Marilyn E.

    2015-12-17

    Using a geology-based assessment methodology, the U.S. Geological Survey estimated mean volumes of 53 trillion cubic feet of shale gas, 172 million barrels of shale oil, and 176 million barrels of natural gas liquids in the Barnett Shale of the Bend Arch–Fort Worth Basin Province of Texas.

  3. Preliminary study of the oil shales of the Green River formation in the tri-state area of Colorado, Utah, and Wyoming to investigate their utility for disposal of radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    1975-05-01

    Results are presented of a preliminary study of the oil shales of the Green River formation in the tri-state area of Colorado, Utah, and Wyoming to investigate their utility for possible disposal of radioactive waste material. The objective of this study was to make a preliminary investigation and to obtain a broad overview of the physical and economic factors which would have an effect on the suitability of the oil shale formations for possible disposal of radioactive waste material. These physical and economic factors are discussed in sections on magnitude of the oil shales, waste disposal relations with oil mining, cavities requirements, hydrological aspects, and study requirements. (JRD)

  4. Viscoelastic Anisotropic Constitutive Law for Rock Shales based on Laboratory Creep Experiments

    Science.gov (United States)

    Trzeciak, Maciej; Sone, Hiroki; Dabrowski, Marcin

    2017-04-01

    In situ stress prediction is critical for successful hydraulic fracturing and later exploitation of an unconventional shale gas/oil reservoir. In order to provide stress models during and after fracturing a reliable stress-strain constitutive law is needed. The most popular models used in the petroleum industry take into account only elastic constitutive laws, which have the assumption of no energy dissipation. As was shown by several authors (e.g. Warpinsky 1986, Gunzburger&Cornet 2007, Sone&Zoback 2013, 2014) viscoelastic creep strain and stress relaxation reach significant amounts in rock shales and should be considered in stress modeling. Viscoelastic functions needed for the constitutive law were obtained during creep experiments on horizontal and vertical shale plugs. We were not in the possesion of samples cut at 45˚ to bedding, and because of that the constitutive relation is limited to the normal strains and stresses. During experiments two creep functions, Ch(t)and Cv(t), and two hereditary Poisson's ratio functions v12(t)and v13(t)were measured. In this paper we present laboratory procedures for creep tests, basic theory of anisotropic (vertical transverse isotropy) viscoelastic constitutive modeling and a simple model of stress relaxation after application of constant strain.

  5. A Laboratory Study of the Effects of Interbeds on Hydraulic Fracture Propagation in Shale Formation

    Directory of Open Access Journals (Sweden)

    Zhiheng Zhao

    2016-07-01

    Full Text Available To investigate how the characteristics of interbeds affect hydraulic fracture propagation in the continental shale formation, a series of 300 mm × 300 mm × 300 mm concrete blocks with varying interbeds, based on outcrop observation and core measurement of Chang 7-2 shale formation, were prepared to conduct the hydraulic fracturing experiments. The results reveal that the breakdown pressure increases with the rise of thickness and strength of interbeds under the same in-situ field stress and injection rate. In addition, for the model blocks with thick and high strength interbeds, the hydraulic fracture has difficulty crossing the interbeds and is prone to divert along the bedding faces, and the fracturing effectiveness is not good. However, for the model blocks with thin and low strength interbeds, more long branches are generated along the main fracture, which is beneficial to the formation of the fracture network. What is more, combining the macroscopic descriptions with microscopic observations, the blocks with thinner and lower strength interbeds tend to generate more micro-fractures, and the width of the fractures is relatively larger on the main fracture planes. Based on the experiments, it is indicated that the propagation of hydraulic fractures is strongly influenced by the characteristics of interbeds, and the results are instructive to the understanding and evaluation of the fracability in the continental shale formation.

  6. Benzene exposure assessed by metabolite excretion in Estonian oil shale mineworkers: influence of glutathione s-transferase polymorphisms

    DEFF Research Database (Denmark)

    Sørensen, Mette; Poole, Jason; Autrup, Herman

    2004-01-01

    at an oil shale mine were compared with the excretion in workers engaged in various production assignments above ground. In addition, possible modifying effects of genetic polymorphisms in glutathione S-transferases T1 (GSTT1), M1 (GSTM1), and P1 (GSTP1) on the excretion of S-PMA and t,t-MA were......-PMA excretion were significantly higher in smokers compared with nonsmokers. Subjects carrying the GSTT1 wild-type excreted higher concentrations of S-PMA than subjects carrying the null genotype, suggesting that it is a key enzyme in the glutathione conjugation that leads to S-PMA. The results support the use...... of benzene metabolites as biomarkers for assessment of exposure at modest levels and warrant for further investigations of health risks of occupational benzene exposure in shale oil mines....

  7. Sustainable Human Presence on the Moon using In Situ Resources

    Science.gov (United States)

    McLemore, Carol A.; Fikes, John C.; McCarley, Kevin S.; Darby, Charles A.; Curreri, Peter A.; Kennedy, James P.; Good, James E.; Gilley, Scott D.

    2008-01-01

    New capabilities, technologies and infrastructure must be developed to enable a sustained human presence on the moon and beyond. The key to having this permanent presence is the utilization of in situ resources. To this end, NASA is investigating how in situ resources can be utilized to improve mission success by reducing up-mass, improving safety, reducing risk, and bringing down costs for the overall mission. To ensure that this capability is available when needed, technology development is required now. NASA/Marshall Space Flight Center (MSFC) is supporting this endeavor, along with other NASA centers, by exploring how lunar regolith can be mined for uses such as construction, life support, propulsion, power, and fabrication. Efforts at MSFC include development of lunar regolith simulant for hardware testing and development, extraction of oxygen and other materials from the lunar regolith, production of parts and tools on the moon from local materials or from provisioned feedstocks, and capabilities to show that produced parts are "ready for use". This paper discusses the lunar regolith, how the regolith is being replicated in the development of simulants and possible uses of the regolith.

  8. ENHANCED DATA DISCOVERABILITY FOR IN SITU HYPERSPECTRAL DATASETS

    Directory of Open Access Journals (Sweden)

    B. Rasaiah

    2016-06-01

    Full Text Available Field spectroscopic metadata is a central component in the quality assurance, reliability, and discoverability of hyperspectral data and the products derived from it. Cataloguing, mining, and interoperability of these datasets rely upon the robustness of metadata protocols for field spectroscopy, and on the software architecture to support the exchange of these datasets. Currently no standard for in situ spectroscopy data or metadata protocols exist. This inhibits the effective sharing of growing volumes of in situ spectroscopy datasets, to exploit the benefits of integrating with the evolving range of data sharing platforms. A core metadataset for field spectroscopy was introduced by Rasaiah et al., (2011-2015 with extended support for specific applications. This paper presents a prototype model for an OGC and ISO compliant platform-independent metadata discovery service aligned to the specific requirements of field spectroscopy. In this study, a proof-of-concept metadata catalogue has been described and deployed in a cloud-based architecture as a demonstration of an operationalized field spectroscopy metadata standard and web-based discovery service.

  9. Guar Gum Stimulates Biogenic Sulfide Production at Elevated Pressures: Implications for Shale Gas Extraction.

    Science.gov (United States)

    Nixon, Sophie L; Walker, Leanne; Streets, Matthew D T; Eden, Bob; Boothman, Christopher; Taylor, Kevin G; Lloyd, Jonathan R

    2017-01-01

    Biogenic sulfide production is a common problem in the oil industry, and can lead to costly hydrocarbon processing and corrosion of extraction infrastructure. The same phenomenon has recently been identified in shale gas extraction by hydraulic fracturing, and organic additives in fracturing fluid have been hypothesized to stimulate this process. Constraining the relative effects of the numerous organic additives on microbial metabolism in situ is, however, extremely challenging. Using a bespoke bioreactor system we sought to assess the potential for guar gum, the most commonly used gelling agent in fracturing fluids, to stimulate biogenic sulfide production by sulfate-reducing microorganisms at elevated pressure. Two pressurized bioreactors were fed with either sulfate-amended freshwater medium, or low-sulfate natural surface water, in addition to guar gum (0.05 w/v%) and an inoculum of sulfate-reducing bacteria for a period of 77 days. Sulfide production was observed in both bioreactors, even when the sulfate concentration was low. Analysis of 16S rRNA gene sequences indicate that heterotrophic bacteria closely associated with the genera Brevundimonas and Acinetobacter became enriched early in the bioreactor experiments, followed by an increase in relative abundance of 16S rRNA genes associated with sulfate-reducing bacteria (Desulfosporosinus and Desulfobacteraceae) at later time points. Results demonstrate that guar gum can stimulate acid- and sulfide-producing microorganisms at elevated pressure, and may have implications for the potential role in microbially induced corrosion during hydraulic fracturing operations. Key differences between experimental and in situ conditions are discussed, as well as additional sources of carbon and energy for biogenic sulfide production during shale gas extraction. Our laboratory approach can be tailored to better simulate deep subsurface conditions in order to probe the role of other fracturing fluid additives and downhole

  10. In-situ characterization of heterogeneous catalysts

    CERN Document Server

    Rodriguez, Jose A; Chupas, Peter J

    2013-01-01

    Helps researchers develop new catalysts for sustainable fuel and chemical production Reviewing the latest developments in the field, this book explores the in-situ characterization of heterogeneous catalysts, enabling readers to take full advantage of the sophisticated techniques used to study heterogeneous catalysts and reaction mechanisms. In using these techniques, readers can learn to improve the selectivity and the performance of catalysts and how to prepare catalysts as efficiently as possible, with minimum waste. In-situ Characterization of Heterogeneous Catalysts feat

  11. Effects of in-situ conditions on relative permeability characteristics of CO2-brine systems

    Science.gov (United States)

    Bachu, Stefan; Bennion, Brant

    2008-06-01

    Carbon dioxide capture and geological storage (CCGS) is an emerging technology that is increasingly being considered for reducing greenhouse gas emissions to the atmosphere. Deep saline aquifers provide a very large capacity for CO2 storage and, unlike hydrocarbon reservoirs and coal beds, are immediately accessible and are found in all sedimentary basins. Proper understanding of the displacement character of CO2-brine systems at in-situ conditions is essential in ascertaining CO2 injectivity, migration and trapping in the pore space as a residual gas or supercritical fluid, and in assessing the suitability and safety of prospective CO2 storage sites. Because of lack of published data, the authors conducted a program of measuring the relative permeability and other displacement characteristics of CO2-brine systems for sandstone, carbonate and shale formations in central Alberta in western Canada. The tested formations are representative of the in-situ characteristics of deep saline aquifers in compacted on-shore North American sedimentary basins. The results show that the capillary pressure, interfacial tension, relative permeability and other displacements characteristics of CO2-brine systems depend on the in-situ conditions of pressure, temperature and water salinity, and on the pore size distribution of the sedimentary rock. This paper presents a synthesis and interpretation of the results.

  12. Hydrocarbon distribution in the Irati shale oil

    Energy Technology Data Exchange (ETDEWEB)

    Afonso, J.C.; Schmal, M.; Cardoso, J.N. [Federal University of Rio de Janeiro, Rio de Janeiro (Brazil)

    1994-03-01

    This work reports a detailed characterization of the various hydrocarbon structures present in a sample of the Irati shale oil (Sao Mateus do Sul, Parana), obtained by the Petrosix Process, by means of a combination of gas chromatography-mass spectrometry (g.c.-m.s.), co-injection with authentic standards, and retention time data of model compounds. Hydrocarbon structures, the main constituents of the shale oil ({approximately} 38 wt%), include: linear, branched and isoprenoidal alkanes, linear and isoprenoidal alkenes, alkycyclopentanes and cyclohexanes, alkylcycloalkenes, hopanes, hopenes and steranes. Linear structures are dominant (43% of the total hydrocarbons), followed by isoprenoidal skeletons. Saturated compounds strongly predominate over their unsaturated counterparts. The use of several maturity parameters attested to the immaturity of the sediment. Data further suggested a predominant algal/microbial origin and a basic lacustrine depositional environment to the Irati shale, probably under a moderate oxidative condition, thus confirming previous conclusions obtained via analysis of the Irati bitumen and the shale rock. Additionally, the data confirmed the usual classification of this shale as containing Type-II kerogen. 34 refs., 2 tabs.

  13. DOE In Situ Remediation Integrated Program. In situ manipulation technologies subprogram plan

    Energy Technology Data Exchange (ETDEWEB)

    Yow, J.L. Jr.

    1993-12-22

    The In Situ Remediation Integrated Program (ISRP) supports and manages a balanced portfolio of applied research and development activities in support of DOE environmental restoration and waste management needs. ISRP technologies are being developed in four areas: containment, chemical and physical treatment, in situ bioremediation, and in situ manipulation (including electrokinetics). the focus of containment is to provide mechanisms to stop contaminant migration through the subsurface. In situ bioremediation and chemical and physical treatment both aim to destroy or eliminate contaminants in groundwater and soils. In situ manipulation (ISM) provides mechanisms to access contaminants or introduce treatment agents into the soil, and includes other technologies necessary to support the implementation of ISR methods. Descriptions of each major program area are provided to set the technical context of the ISM subprogram. Typical ISM needs for major areas of in situ remediation research and development are identified.

  14. Development of a Highly Portable Plate Loading Device and In Situ Modulus Measurements in Weak Rock Masses

    Science.gov (United States)

    Kallu, Raj R.; Keffeler, Evan R.; Watters, Robert J.; Warren, Sean N.

    2016-02-01

    In recent years, underground mines in Nevada are increasingly exploiting in weak mineralized zones at greater depths that are intensely fractured and highly altered. The mechanical behavior of these rock masses ranges between weak rock and very stiff soil. A common limitation for design of underground mining excavations in these types of rock masses is absence of in situ geotechnical data. This limitation is generally overcome by estimating in situ mechanical behavior from empirical relationships so that the continuum-based numerical methods can be used to evaluate ground support designs. Because of the cost, time, and specialized equipment involved, historically in situ tests have not been performed in these underground mines. Predictive rock mass modulus relationships that are currently available in the literature are derived from field testing of predominantly good-quality rock masses. Consequently, there is limited confidence in using these models for rock masses with Rock Mass Ratings less than 45. In order to overcome some of these limitations, a portable plate loading device (PPLD) was designed and fabricated. The PPLD allows one to perform low cost and relatively quick in situ deformability tests to be performed on weak rock masses in underground mines. Test procedures and data reduction methods were developed to limit potential sources of error associated with the PPLD test. A total of fourteen plate loading tests were performed in weak rock masses at two different active underground mines in Nevada, USA. The resulting the test data were compared to eight published empirical rock mass modulus relationships to determine which, if any, of these relationships are sufficiently accurate for estimating modulus in similar geotechnical conditions. Only two of these relationships were found to be sufficient for first-order estimations of in situ modulus.

  15. Effects of organic wastes on water quality from processing of oil shale from the Green River Formation, Colorado, Utah, and Wyoming

    Science.gov (United States)

    Leenheer, J.A.; Noyes, T.I.

    1986-01-01

    A series of investigations were conducted during a 6-year research project to determine the nature and effects of organic wastes from processing of Green River Formation oil shale on water quality. Fifty percent of the organic compounds in two retort wastewaters were identified as various aromatic amines, mono- and dicarboxylic acids phenols, amides, alcohols, ketones, nitriles, and hydroxypyridines. Spent shales with carbonaceous coatings were found to have good sorbent properties for organic constituents of retort wastewaters. However, soils sampled adjacent to an in situ retort had only fair sorbent properties for organic constituents or retort wastewater, and application of retort wastewater caused disruption of soil structure characteristics and extracted soil organic matter constituents. Microbiological degradation of organic solutes in retort wastewaters was found to occur preferentially in hydrocarbons and fatty acid groups of compounds. Aromatic amines did not degrade and they inhibited bacterial growth where their concentrations were significant. Ammonia, aromatic amines, and thiocyanate persisted in groundwater contaminated by in situ oil shale retorting, but thiosulfate was quantitatively degraded one year after the burn. Thiocyanate was found to be the best conservative tracer for retort water discharged into groundwater. Natural organic solutes, isolated from groundwater in contact with Green River Formation oil shale and from the White River near Rangely, Colorado, were readily distinguished from organic constituents in retort wastewaters by molecular weight and chemical characteristic differences. (USGS)

  16. Hydrologic properties of shale and related argillaceous rocks

    Energy Technology Data Exchange (ETDEWEB)

    Moiseyev, A.N.

    1979-11-15

    This report is the result of a bibliographic study designed primarily to collect hydrologic data on American clay-rich rocks. The following information was also sought: stratigraphy, environment of deposition, mineralogic composition, and diagenetic changes. The collected numerical data are presented in tables which contain densities, porosities, and/or hydraulic conductivities of approximately 360 samples. Additional data include hydraulic diffusivities, resistivities, flow rates, and rock strengths. Geologic information suggests that large deposits of shale which may be suited for waste repository belong to all ages and were formed in both marine and continental environments. Of the studied units, the most promising are Paleozoic in the eastern half of the country, Mesozoic in the central part, and Cenozoic in the Gulf Coast area and the West. Less widespread units locally present some additional possibilities. Mineralogic investigations suggest that the smectite content in rocks shows a decrease in time (70% in Recent rocks; 35% in pre-Mesozoic rocks). Because of this predominance of smectite in younger rocks, the modeling of repositories in post-Paleozoic formations might require knowledge of additional and poorly known parameters. Results of investigations into the mathematical relationships between porosity and permeability (or hydralic conductivity) suggest that in situ permeabilities could be estimated from sonic logs and fluid pressure changes at depth. 16 figures, 8 tables.

  17. 4D imaging of fluid escape in low permeability shales during heating

    Science.gov (United States)

    Renard, F.; Kobchenko, M.

    2012-04-01

    The coupling between thermal effects and deformation is relevant in many natural geological environments (rising magma, primary migration of hydrocarbons, vents) and has many industrial applications (storage of nuclear wastes, enhanced hydrocarbon recovery, coal exploitation, geothermic plants). When thermal effects involve phase transformation in the rock and production of fluids, a strong coupling may emerge between the processes of fluid escape and the ability of the rock to deform and transport fluids. To better understand the mechanisms of fracture pattern development and fluid escape in low permeability rocks, we performed time-resolved in situ X-ray tomography imaging to investigate the processes that occur during the slow heating (from 60° to 400°C) of organic-rich Green River shale. At about 350°C cracks nucleated in the sample, and as the temperature continued to increase, these cracks propagated parallel to shale bedding and coalesced, thus cutting across the sample. Thermogravimetry and gas chromatography revealed that the fracturing occurring at ~350°C was associated with significant mass loss and release of light hydrocarbons generated by the decomposition of immature organic matter. Kerogen decomposition is thought to cause an internal pressure build up sufficient to form cracks in the shale, thus providing pathways for the outgoing hydrocarbons. We show that a 2D numerical model based on this idea qualitatively reproduces the experimentally observed dynamics of crack nucleation, growth and coalescence, as well as the irregular outlines of the cracks. Our results provide a new description of fracture pattern formation in low permeability shales.

  18. Methanogenic archaea in marcellus shale: a possible mechanism for enhanced gas recovery in unconventional shale resources.

    Science.gov (United States)

    Tucker, Yael Tarlovsky; Kotcon, James; Mroz, Thomas

    2015-06-02

    Marcellus Shale occurs at depths of 1.5-2.5 km (5000 to 8000 feet) where most geologists generally assume that thermogenic processes are the only source of natural gas. However, methanogens in produced fluids and isotopic signatures of biogenic methane in this deep shale have recently been discovered. This study explores whether those methanogens are indigenous to the shale or are introduced during drilling and hydraulic fracturing. DNA was extracted from Marcellus Shale core samples, preinjected fluids, and produced fluids and was analyzed using Miseq sequencing of 16s rRNA genes. Methanogens present in shale cores were similar to methanogens in produced fluids. No methanogens were detected in injected fluids, suggesting that this is an unlikely source and that they may be native to the shale itself. Bench-top methane production tests of shale core and produced fluids suggest that these organisms are alive and active under simulated reservoir conditions. Growth conditions designed to simulate the hydrofracture processes indicated somewhat increased methane production; however, fluids alone produced relatively little methane. Together, these results suggest that some biogenic methane may be produced in these wells and that hydrofracture fluids currently used to stimulate gas recovery could stimulate methanogens and their rate of producing methane.

  19. Hydrogeological aspects of shale gas extraction in the UK

    OpenAIRE

    Stuart, Marianne

    2014-01-01

    UK shale gas exploitation currently at a very early stage. Potentially significant quantities but resources are not yet proven. In the UK a number of the potentially exploitable shales are below important aquifers.Water demand for shale gas production may not be significant relative to other uses but local needs must be considered carefully. Shale gas extraction will use/mobilise potential pollutants. Risks must be fully assessed and managed effectively – through to post abandonment. The most...

  20. Perspectives and Problems related to the Shale Gas Production

    Directory of Open Access Journals (Sweden)

    D. P. Gerish

    2014-12-01

    Full Text Available This article describes the main aspects of shale gas production, its origin and properties. The particular issues related to the shale gas production, as well as the public and official attitude to the perspectives of its usage in Russian Federation are analyzed. The general problems of the shale gas exploration and production in the Russian Federation are discussed. The current and prognostic rates of shale gas production in USA are shown.

  1. Finite element analysis of effect of underground coal mining on landslide of the Wei Mountain

    Energy Technology Data Exchange (ETDEWEB)

    Shan Xioa-yun; Jiang Yao-dong; Wang Le-jie; Zhao Yi-xin; Hong Yi-qing [China University of Mining and Technology, Beijing (China). School of Mechanics, Architecture and Civil Engineering

    2008-01-15

    A study of the landslide of Wei Mountain near Zhaogezhuang coal mine in the Kailuan mining area was made in respect of the cause, development and relationship with underground mining, using methods of in-situ monitoring, numerical simulation and analysis of comprehensive coupling factors based on summarizing and analyzing previous information. Results of numerical simulation and in-situ monitoring show that, as long as the slope base is not damaged, no large landslide would occur and the main cause of damage of underground mining is horizontal movement of the south of the mountain in a southerly direction. 5 refs., 7 figs., 2 tabs.

  2. Sentinel Mining

    DEFF Research Database (Denmark)

    Middelfart, Morten

    into geography dimension) combined with a decrease in the money invested in customer support for laptop computers (drilldown into product dimension) is observed. The work leading to this thesis progressed from algorithms for regular sentinel mining with only one source and one target measure, into algorithms...... progression in the efficiency of sentinel mining, where the latest bitmap-based algorithms, that also take advantage of modern CPUs, are 3–4 orders of magnitude faster than the first SQL-based sentinel mining algorithm. This work also led to the industrial implementation of sentinel mining in the commercial...

  3. Fracture propagation during fluid injection experiments in shale at elevated confining pressures.

    Science.gov (United States)

    Chandler, Mike; Mecklenburgh, Julian; Rutter, Ernest; Fauchille, Anne-Laure; Taylor, Rochelle; Lee, Peter

    2017-04-01

    The use of hydraulic fracturing to recover shale-gas has focused attention upon the fundamental fracture properties of gas-bearing shales. Fracture propagation trajectories in these materials depend on the interaction between the anisotropic mechanical properties of the shale and the anisotropic in-situ stress field. However, there is a general paucity of available experimental data on their anisotropic mechanical, physical and fluid-flow properties, especially at elevated confining pressures. Here we report the results of laboratory-scale fluid injection experiments, for Whitby mudstone and Mancos shale (an interbedded silt and mudstone), as well as Pennant sandstone (a tight sandstone with permeability similar to shales), which is used an isotropic baseline and tight-gas sandstone analogue. Our injection experiments involved the pressurisation of a blind-ending central hole in an initially dry cylindrical sample. Pressurisation was conducted under constant volume-rate control, using silicone oils of various viscosities. The dependence of breakdown pressure on confining pressure was seen to be dependent on the rock strength, with the significantly stronger Pennant sandstone exhibiting much lower confining-pressure dependence of breakdown pressure than the weaker shales. In most experiments, a small drop in the injection pressure record was observed at what is taken to be fracture initiation, and in the Pennant sandstone this was accompanied by a small burst of acoustic energy. Breakdown was found to be rapid and uncontrollable after initiation if injection is continued, but can be limited to a slower (but still uncontrolled) rate by ceasing the injection of fluid after the breakdown initiation in experiments where it could be identified. A simplified 2-dimensional model for explaining these observations is presented in terms of the stress intensities at the tip of a pressurised crack. Additionally, we present a suite of supporting mechanical, flow and elastic

  4. Extraction of hydrocarbons from high-maturity Marcellus Shale using supercritical carbon dioxide

    Science.gov (United States)

    Jarboe, Palma B.; Philip A. Candela,; Wenlu Zhu,; Alan J. Kaufman,

    2015-01-01

    Shale is now commonly exploited as a hydrocarbon resource. Due to the high degree of geochemical and petrophysical heterogeneity both between shale reservoirs and within a single reservoir, there is a growing need to find more efficient methods of extracting petroleum compounds (crude oil, natural gas, bitumen) from potential source rocks. In this study, supercritical carbon dioxide (CO2) was used to extract n-aliphatic hydrocarbons from ground samples of Marcellus shale. Samples were collected from vertically drilled wells in central and western Pennsylvania, USA, with total organic carbon (TOC) content ranging from 1.5 to 6.2 wt %. Extraction temperature and pressure conditions (80 °C and 21.7 MPa, respectively) were chosen to represent approximate in situ reservoir conditions at sample depth (1920−2280 m). Hydrocarbon yield was evaluated as a function of sample matrix particle size (sieve size) over the following size ranges: 1000−500 μm, 250−125 μm, and 63−25 μm. Several methods of shale characterization including Rock-Eval II pyrolysis, organic petrography, Brunauer−Emmett−Teller surface area, and X-ray diffraction analyses were also performed to better understand potential controls on extraction yields. Despite high sample thermal maturity, results show that supercritical CO2 can liberate diesel-range (n-C11 through n-C21) n-aliphatic hydrocarbons. The total quantity of extracted, resolvable n-aliphatic hydrocarbons ranges from approximately 0.3 to 12 mg of hydrocarbon per gram of TOC. Sieve size does have an effect on extraction yield, with highest recovery from the 250−125 μm size fraction. However, the significance of this effect is limited, likely due to the low size ranges of the extracted shale particles. Additional trends in hydrocarbon yield are observed among all samples, regardless of sieve size: 1) yield increases as a function of specific surface area (r2 = 0.78); and 2) both yield and surface area increase with increasing

  5. Thermocatalytical processing of coal and shales

    Directory of Open Access Journals (Sweden)

    Zhaksyntay Kairbekov

    2012-12-01

    Full Text Available The article investigates the questions of thermocatalytical conversion of organic mass of coal (OMC, it is shown that in the absence of a catalyst process is carried out by a radical process. Accumulated data on the properties for radicals of different structure and therefore different reaction capacity enables us to understand and interpret the conversion of OMC. Thermal conversion of OMC regarded as a kind of depolymerization, accompanied by decomposition of the functional groups with the formation of radicals, competing for hydrogen atom. Catalyst can change the direction and conditions of the process. Modern catalysts can reduce the process pressure up to 50 atm., with a high degree of coal conversion. We consider examples of simultaneous conversion of coal and shale, shale and masut, shale and tar.

  6. Multiphysical Testing of Soils and Shales

    CERN Document Server

    Ferrari, Alessio

    2013-01-01

    Significant advancements in the experimental analysis of soils and shales have been achieved during the last few decades. Outstanding progress in the field has led to the theoretical development of geomechanical theories and important engineering applications. This book provides the reader with an overview of recent advances in a variety of advanced experimental techniques and results for the analysis of the behaviour of geomaterials under multiphysical testing conditions. Modern trends in experimental geomechanics for soils and shales are discussed, including testing materials in variably saturated conditions, non-isothermal experiments, micro-scale investigations and image analysis techniques. Six theme papers from leading researchers in experimental geomechanics are also included. This book is intended for postgraduate students, researchers and practitioners in fields where multiphysical testing of soils and shales plays a fundamental role, such as unsaturated soil and rock mechanics, petroleum engineering...

  7. Screening restimulation candidates in the Antrim Shale

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, C.W.; Frantz, J.H. Jr.; Tatum, C.L.; Hill, D.G.

    1994-12-31

    This paper describes a simple method to identify, prioritize, and evaluate restimulation candidates in the Antrim Shale of the Michigan Basin. This work is being performed as part of an ongoing field-based Gas Research Institute (GRI) project investigating the Antrim Shale. There are between 500 and 1,000 Antrim Shale wells which could be candidates for restimulation due to previous screenouts and/or flowback problems, when sand consolidation material was not used. However, all of these wells might not benefit from restimulation, due to either poor reservoir quality or because the wells are already effectively stimulated. Based on historical results, the authors estimate the increase in reserves from restimulation could be between 50 and 400 MMscf per well, which could add 50 to 200 Bscf in future reserves from the 500--1,000 candidate wells.

  8. Assessment of potential unconventional lacustrine shale-oil and shale-gas resources, Phitsanulok Basin, Thailand, 2014

    Science.gov (United States)

    Schenk, Christopher J.; Charpentier, Ronald R.; Klett, Timothy R.; Mercier, Tracey J.; Tennyson, Marilyn E.; Pitman, Janet K.; Brownfield, Michael E.

    2014-01-01

    Using a geology-based assessment methodology, the U.S. Geological Survey assessed potential technically recoverable mean resources of 53 million barrels of shale oil and 320 billion cubic feet of shale gas in the Phitsanulok Basin, onshore Thailand.

  9. Shales: A review of their classifications, properties and importance ...

    African Journals Online (AJOL)

    Shales are fine-grained, laminated or fissile clastic sedimentary rocks with predominance of clay and silt as the detrital components. They may be classified as clayey, silty or sandy shales on the basis of texture. Other criteria used in the classification of shales include mineralogical composition, cementing materials, organic ...

  10. Rapid gas development in the Fayetteville shale basin, Arkansas

    Science.gov (United States)

    Advances in drilling and extraction of natural gas have resulted in rapid expansion of wells in shale basins. The rate of gas well installation in the Fayetteville shale is 774 wells a year since 2005 with thousands more planned. The Fayetteville shale covers 23,000 km2 although ...

  11. Kinetic simulation model for steam pyrolysis of shale oil feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Kavianian, H.R.; Yesavage, V.F.; Dickson, P.F.; Peters, R.W. (Argonne National Lab., Argonne, IL (US))

    1990-04-01

    Steam pyrolysis of shale oil feedstocks for the production of chemical intermediates was studied in a bench-scale tubular reactor. The results have been correlated as a function of temperature, residence time, and pyrolysis severity. The experimental results obtained upon pyrolysis of shale oil indicate that shale oil should make an excellent feedstock for steam pyrolysis.

  12. Treatment of multivariate environmental and health problems associated with oil shale technology

    Energy Technology Data Exchange (ETDEWEB)

    Kland, M.J.

    1980-07-01

    A statistical matrix approach for solving complex environmental problems involving oil shale mining and processing is presented. Four methods are described: quantitative structure-activity and molecular connectivity relationships (QSAR,MC); factor analysis (FA); and pattern recognition (PR). QSAR and MC are useful in the prediction of toxic behavior for individual members of a class of compounds for which SAR data are already available. The methods of FA and PR have both been applied to data derived from structure-activity relationships (SAR), and PR techniques have also been used with connectivity functions. Each method is evaluated and the scope of their application is defined. (DMC)

  13. Flowback patterns of fractured shale gas wells

    Directory of Open Access Journals (Sweden)

    Naizhen Liu

    2015-03-01

    Full Text Available Shale gas reservoirs generally need to be fractured massively to reach the industrial production, however, the flowback ratio of fractured shale gas wells is low. In view of this issue, the effects of natural fracture spacing, fracture conductivity, fracturing scale, pressure coefficient and shut-in time on the flowback ratio were examined by means of numerical simulation and experiments jointly, and the causes of flowback difficulty of shale gas wells were analyzed. The results show that the flowback ratio increases with the increase of natural fracture spacing, fracture conductivity and pressure coefficient and decreases with the increase of fracturing scale and shut-in time. From the perspective of microscopic mechanism, when water enters micro-cracks of the matrix through the capillary self-absorbing effect, the original hydrogen bonds between the particles are replaced by the hydroxyl group, namely, hydration effect, giving rise to the growth of new micro-cracks and propagation of main fractures, and complex fracture networks, so a large proportion of water cannot flow back, resulting in a low flowback ratio. For shale gas well fracturing generally has small fracture space, low fracture conductivity and big fracturing volume, a large proportion of the injected water will be held in the very complex fracture network with a big specific area, and unable to flow back. It is concluded that the flowback ratio of fractured shale gas wells is affected by several factors, so it is not necessary to seek high flowback ratio deliberately, and shale gas wells with low flowback ratio, instead, usually have high production.

  14. Mars Colony in situ resource utilization: An integrated architecture and economics model

    Science.gov (United States)

    Shishko, Robert; Fradet, René; Do, Sydney; Saydam, Serkan; Tapia-Cortez, Carlos; Dempster, Andrew G.; Coulton, Jeff

    2017-09-01

    This paper reports on our effort to develop an ensemble of specialized models to explore the commercial potential of mining water/ice on Mars in support of a Mars Colony. This ensemble starts with a formal systems architecting framework to describe a Mars Colony and capture its artifacts' parameters and technical attributes. The resulting database is then linked to a variety of ;downstream; analytic models. In particular, we integrated an extraction process (i.e., ;mining;) model, a simulation of the colony's environmental control and life support infrastructure known as HabNet, and a risk-based economics model. The mining model focuses on the technologies associated with in situ resource extraction, processing, storage and handling, and delivery. This model computes the production rate as a function of the systems' technical parameters and the local Mars environment. HabNet simulates the fundamental sustainability relationships associated with establishing and maintaining the colony's population. The economics model brings together market information, investment and operating costs, along with measures of market uncertainty and Monte Carlo techniques, with the objective of determining the profitability of commercial water/ice in situ mining operations. All told, over 50 market and technical parameters can be varied in order to address ;what-if; questions, including colony location.

  15. New York Marcellus Shale: Industry boom put on hold

    Energy Technology Data Exchange (ETDEWEB)

    Mercurio, Angelique

    2012-01-16

    , New Mexico, North Dakota, Ohio, Oklahoma, Pennsylvania, South Dakota, Texas, Utah, West Virginia, and Wyoming are pursuing. Positive labor market impacts are another major economic draw. According to the Revised Draft SGEIS on the Oil, Gas and Solution Mining Regulatory Program (September 2011), hydraulic fracturing would create between 4,408 and 17,634 full-time equivalent (FTE) direct construction jobs in New York State. Indirect employment in other sectors would add an additional 29,174 FTE jobs. Furthermore, the SGEIS analysis suggests that drilling activities could add an estimated $621.9 million to $2.5 billion in employee earnings (direct and indirect) per year, depending upon how much of the shale is developed. The state would also receive direct tax receipts from leasing land, and has the potential to see an increase in generated indirect revenue. Estimates range from $31 million to $125 million per year in personal income tax receipts, and local governments would benefit from revenue sharing. Some landowner groups say the continued delay in drilling is costing tens of thousands of jobs and millions of dollars in growth for New York, especially in the economically stunted upstate. A number of New York counties near Pennsylvania, such as Chemung, NY, have experienced economic uptick from Pennsylvania drilling activity just across the border. Chemung officials reported that approximately 1,300 county residents are currently employed by the drilling industry in Pennsylvania. The Marcellus shale boom is expected to continue over the next decade and beyond. By 2015, gas drilling activity could bring 20,000 jobs to New York State alone. Other states, such as Pennsylvania and West Virginia, are also expected to see a significant increase in the number of jobs. Catalyst 2: Political Reality of the Moratorium. Oil and gas drilling has taken place in New York since the 19th century, and it remains an important industry with more than 13,000 currently active wells. The

  16. The modernisation of mining

    CSIR Research Space (South Africa)

    Ritchken, E

    2017-10-01

    Full Text Available This presentation discusses the modernisation of mining. The presentation focuses on the mining clusters, Mining Challenges, Compliance versus Collaboration, The Phakisa, The Mining Precinct & the Mining Hub also Win-Win Beneficiation: Iron...

  17. ADVANTAGES/DISADVANTAGES FOR ISCO METHODS IN-SITU FENTON OXIDATION IN-SITU PERMANGANATE OXIDATION

    Science.gov (United States)

    The advantages and disadvantages of in-situ Fenton oxidation and in-situ permanganate oxidation will be presented. This presentation will provide a brief overview of each technology and a detailed analysis of the advantages and disadvantages of each technology. Included in the ...

  18. Rate and State Frictional Properties of Shale Gas Reservoir Rocks and FIB/SEM Microscopy of Lab-Generated Fault Surfaces

    Science.gov (United States)

    Kohli, A. H.; Zoback, M. D.

    2011-12-01

    To investigate the slip behavior of natural faults in shale gas reservoirs under the conditions of hydraulic stimulation, we conduct laboratory investigations of the frictional and hydrologic properties of shale gas reservoir rocks. We report on several initial studies of the frictional properties of cores from the Haynesville and Eagleford shale reservoirs, performed under dry and wet conditions and in-situ confining and pore pressures. The results of velocity-stepping experiments show strongly velocity-strengthening frictional behavior at sliding velocities ranging from 0.1 - 100 μm/s and sliding displacements of up to 5 mm. Focused ion beam and scanning electron microscopy of the fault sliding surfaces from these experiments reveals slickenside lineations in the direction of fault slip and significant production of sub-micron clay gouge. In addition, fault surface damage is visible in the form of bedding-parallel, micron scale cracks, which form at pre-existing pores in the intact shale matrix, suggesting a mechanism for permeability enhancement during slow slip. These results are evaluated in terms of rate-and-state constitutive models for frictional stability to develop a physical model for induced slip by hydraulic stimulation in shale gas reservoirs.

  19. Detection of potential methane gas pathways in deep South African gold mines

    Science.gov (United States)

    Mkhabela, Mbali; Manzi, Musa

    2017-08-01

    At a number of gold mines in South Africa, methane gas has been encountered when drilling into faults and/or dykes extending to depths beyond 7000 m. Methane gas has been reported to migrate up through structures from within the basin to the mine working environments (∼3000 m depth) and caused explosions. The Booysens Shale is one of the possible source rocks for hydrocarbons and it forms the footwall to the gold-bearing Ventersdorp Contact Reef (VCR, ∼1.5 m thick). The Booysens Shale lies at depths between 3500 and 4500 m below the surface and can be best described as a base of the divergent clastic wedge, hosting the quartzite and conglomerate units that sub-crop against the VCR towards the west of the gold mining areas. Geometric attributes (dip and dip azimuth) and instantaneous attributes (phase, frequency and envelope) computed for the Booysens Shale and VCR horizons provide insight into structures that extend from the Booysens Shale into the overlying mining level (i.e. VCR). These attributes successfully mapped the structures (faults and dykes) that have displaced both the VCR and Booysens Shale horizons. The edge-detection attributes were particularly useful in delineating faults with throws below the traditional seismic resolution criteria (e.g. a quarter of the dominant wavelength) that were not visible in the conventional seismic interpretation. The structural analysis using seismic attributes gives a new visual representation of geological structures that may be probable conduits for hydrocarbons, particularly methane, migrating from the Booysens Shale to the VCR mining levels.

  20. In Situ TEM Creation of Nanowire Devices

    DEFF Research Database (Denmark)

    Alam, Sardar Bilal

    Integration of silicon nanowires (SiNWs) as active components in devices requires that desired mechanical, thermal and electrical interfaces can be established between the nanoscale geometry of the SiNW and the microscale architecture of the device. In situ transmission electron microscopy (TEM...... of SiNW were also investigated in situ. SiNWs were grown on silicon microcantilever heaters using the VLS mechanism. When grown across a gap between adjacent cantilevers, contact was formed when the SiNW impinged on the sidewall of an adjacent cantilever. Using in situ TEM, SiNW contact formation...... process at high temperatures was observed in real time. As the eutectic droplet made contact, it wetted the surface; Si growth catalyzed by the eutectic continued, while at the same time Au often migrated/diffused away from the contact site. The parameters of this contact formation process were measured...

  1. Petroleum recovery by in situ combustion

    Energy Technology Data Exchange (ETDEWEB)

    Orkiszewski, J.

    1968-09-10

    In an in situ combustion process for the recovery of oil, the available fuel is changed to more nearly equal the minimum fuel requirement for the process. The API gravity of the reservoir oil and the temperature of the reservoir are used to determine the total available fuel. The available fuel in the reservoir is changed to more nearly equal the minimum fuel requirement for the in situ combustion process by injecting a fluid capable of changing either the API gravity of the reservoir oil, the reservoir temperature, or both. An oxygen containing gas is then injected into the reservoir to initiate combustion. Oil is recovered from the reservoir as a result of the in situ combustion process. (10 claims)

  2. Design Games for In-Situ Design

    DEFF Research Database (Denmark)

    Kristiansen, Erik

    2013-01-01

    The mobile culture has spawned a host of context-based products, like location-based and tag-based applications. This presents a new challenge for the designer. There is a need of design methods that acknowledge the context and allows it to influence the design ideas. This article focuses...... on a design problem where an in-situ design practice may further the early design process: the case of designing a pervasive game. Pervasive games are computer games, played using the city as a game board and often using mobile phones with GPS. Some contextual design methods exist, but we propose an approach...... that calls for the designer to conceptualise and perform ideas in-situ, that is on the site, where the game is supposed to be played. The problem was to design a creativity method that incorporated in-situ design work and which generated game concepts for pervasive games. The proposed design method, called...

  3. In situ macromolecular crystallography using microbeams.

    Science.gov (United States)

    Axford, Danny; Owen, Robin L; Aishima, Jun; Foadi, James; Morgan, Ann W; Robinson, James I; Nettleship, Joanne E; Owens, Raymond J; Moraes, Isabel; Fry, Elizabeth E; Grimes, Jonathan M; Harlos, Karl; Kotecha, Abhay; Ren, Jingshan; Sutton, Geoff; Walter, Thomas S; Stuart, David I; Evans, Gwyndaf

    2012-05-01

    Despite significant progress in high-throughput methods in macromolecular crystallography, the production of diffraction-quality crystals remains a major bottleneck. By recording diffraction in situ from crystals in their crystallization plates at room temperature, a number of problems associated with crystal handling and cryoprotection can be side-stepped. Using a dedicated goniometer installed on the microfocus macromolecular crystallography beamline I24 at Diamond Light Source, crystals have been studied in situ with an intense and flexible microfocus beam, allowing weakly diffracting samples to be assessed without a manual crystal-handling step but with good signal to noise, despite the background scatter from the plate. A number of case studies are reported: the structure solution of bovine enterovirus 2, crystallization screening of membrane proteins and complexes, and structure solution from crystallization hits produced via a high-throughput pipeline. These demonstrate the potential for in situ data collection and structure solution with microbeams. © 2012 International Union of Crystallography

  4. Is shale gas drilling an energy solution or public health crisis?

    Science.gov (United States)

    Rafferty, Margaret A; Limonik, Elena

    2013-01-01

    High-volume horizontal hydraulic fracturing, a controversial new mining technique used to drill for shale gas, is being implemented worldwide. Chemicals used in the process are known neurotoxins, carcinogens, and endocrine disruptors. People who live near shale gas drilling sites report symptoms that they attribute to contaminated air and water. When they seek help from clinicians, a diagnosis is often elusive because the chemicals to which the patients have been exposed are a closely guarded trade secret. Many nurses have voiced grave concern about shale gas drilling safety. Full disclosure of the chemicals used in the process is necessary in order for nurses and other health professionals to effectively care for patients. The economic exuberance surrounding natural gas has resulted in insufficient scrutiny into the health implications. Nursing research aimed at determining what effect unconventional drilling has on human health could help fill that gap. Public health nurses using the precautionary principle should advocate for a more concerted transition from fossil fuels to sustainable energy. Any initiation or further expansion of unconventional gas drilling must be preceded by a comprehensive Health Impact Assessment (HIA). © 2013 Wiley Periodicals, Inc.

  5. Fourier Transform Infrared Spectroscopic Determination of Shale ...

    African Journals Online (AJOL)

    The CLS model developed was able to quantify the mineral components of independent mixtures with an absolute error between 1 to 3wt% for all the pure minerals in the mixtures. Samples from a suite of shale reservoir rocks were analysed using standard Quantitative X-Ray Diffraction (QXRD) and with FTIR. Unknown ...

  6. Paleontology: a new Burgess Shale fauna.

    Science.gov (United States)

    Briggs, Derek E G

    2014-05-19

    A spectacular Cambrian soft bodied fauna some 40 km from Walcott's original Burgess Shale locality includes over 50 taxa, some 20% new to science. New anatomical evidence from this site will illuminate the evolution of early marine animals. Copyright © 2014 Elsevier Ltd. All rights reserved.

  7. [Chemical hazards arising from shale gas extraction].

    Science.gov (United States)

    Pakulska, Daria

    2015-01-01

    The development of the shale industry is gaining momentum and hence the analysis of chemical hazards to the environment and health of the local population is extreiely timely and important. Chemical hazards are created during the exploitation of all minerals, but in the case of shale gas production, there is much more uncertainty as regards to the effects of new technologies application. American experience suggests the increasing risk of environmental contamination, mainly groundwater. The greatest, concern is the incomplete knowledge of the composition of fluids used for fracturing shale rock and unpredictability of long-term effects of hydraulic fracturing for the environment and health of residents. High population density in the old continent causes the problem of chemical hazards which is much larger than in the USA. Despite the growing public discontent data on this subject are limited. First of all, there is no epidemiological studies to assess the relationship between risk factors, such as air and water pollution, and health effects in populations living in close proximity to gas wells. The aim of this article is to identify and discuss existing concepts on the sources of environmental contamination, an indication of the environment elements under pressure and potential health risks arising from shale gas extraction.

  8. Chemical hazards arising from shale gas extraction

    Directory of Open Access Journals (Sweden)

    Daria Pakulska

    2015-02-01

    Full Text Available The development of the shale industry is gaining momentum and hence the analysis of chemical hazards to the environment and health of the local population is extremely timely and important. Chemical hazards are created during the exploitation of all minerals, but in the case of shale gas production, there is much more uncertainty as regards to the effects of new technologies application. American experience suggests the increasing risk of environmental contamination, mainly groundwater. The greatest concern is the incomplete knowledge of the composition of fluids used for fracturing shale rock and unpredictability of long-term effects of hydraulic fracturing for the environment and health of residents. High population density in the old continent causes the problem of chemical hazards which is much larger than in the USA. Despite the growing public discontent data on this subject are limited. First of all, there is no epidemiological studies to assess the relationship between risk factors, such as air and water pollution, and health effects in populations living in close proximity to gas wells. The aim of this article is to identify and discuss existing concepts on the sources of environmental contamination, an indication of the environment elements under pressure and potential health risks arising from shale gas extraction. Med Pr 2015;66(1:99–117

  9. Electromagnetic De-Shaling of Coal

    NARCIS (Netherlands)

    De Jong, T.P.R.; Mesina, M.B.; Kuilman, W.

    2003-01-01

    The efficiency with which an electromagnetic sensor array is able to distinguish density and ash content of coal and shale mixtures was determined experimentally. The investigated sensor was originally designed for automatic metal detection and sorting in industrial glass recycle processing, where

  10. Technically recoverable Devonian shale gas in Ohio

    Energy Technology Data Exchange (ETDEWEB)

    Kuushraa, V.A.; Wicks, D.E.; Sawyer, W.K.; Esposito, P.R.

    1983-07-01

    The technically recoverable gas from Devonian shale (Lower and Middle Huron) in Ohio is estimated to range from 6.2 to 22.5 Tcf, depending on the stimulation method and pattern size selected. This estimate of recovery is based on the integration of the most recent data and research on the Devonian Age gas-bearing shales of Ohio. This includes: (1) a compilation of the latest geologic and reservoir data for the gas in-place; (2) analysis of the key productive mechanisms; and, (3) examination of alternative stimulation and production strategies for most efficiently recovering this gas. Beyond a comprehensive assembly of the data and calculation of the technically recoverable gas, the key findings of this report are as follows: a substantial volume of gas is technically recoverable, although advanced (larger scale) stimulation technology will be required to reach economically attractive gas production rates in much of the state; well spacing in certain of the areas can be reduced by half from the traditional 150 to 160 acres per well without severely impairing per-well gas recovery; and, due to the relatively high degree of permeability anisotropy in the Devonian shales, a rectangular, generally 3 by 1 well pattern leads to optimum recovery. Finally, although a consistent geological interpretation and model have been constructed for the Lower and Middle Huron intervals of the Ohio Devonian shale, this interpretation is founded on limited data currently available, along with numerous technical assumptions that need further verification. 11 references, 21 figures, 32 tables.

  11. The decomposition of Posidonia Shale and Green River Shale kerogens using microscale sealed vessel (MSSV) pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Horsfield, B.; Dueppenbecker, S.J. (Kernforschungsanlage Juelich GmbH (Germany, F.R.))

    1991-01-01

    Microscale sealed vessel (MSSV) pyrolysis was used to simulate the compositional evolution of products generated from Posidonia Shale and Green River Shale kerogens with increasing maturity. Conversion was measured using a pseudo-Rock-Eval approach. Temperatures in the range 300-350{degree}C and heating times between 1 and 10 days resulted in a 10-90% conversion of Posidonia Shale kerogen and 3-60% conversion of Green River Shale kerogen into volatile products. Single step GC analysis (C{sub 1}-C{sub 30} range) revealed the presence of aliphatic hydrocarbons, aromatic hydrocarbons, sulphur-containing compounds and a complex mixture of unresolved components. The Posidonia Shale kerogen was inferred to have generated mainly heavy bitumen for all low temperature (300{sup 0}C) experiments and for higher temperature experiments of short duration. At higher temperatures and longer heating times this material, possibly derived from alkyl-substituted naphthenoaromatic units in the kerogen, decomposed to yield products, detectable by gas chromatography, with an enhanced gas to oil ratio. Bitumen generated from Green River Shale appears to have a lower average molecular weight and/or polarity. Normal alkanes with a fixed chain length distribution were generated from what appears to be biopolymeric structures in both kerogen types. 9 figs., 52 refs.

  12. Shale characterization on Barito field, Southeast Kalimantan for shale hydrocarbon exploration

    Science.gov (United States)

    Sumotarto, T. A.; Haris, A.; Riyanto, A.; Usman, A.

    2017-07-01

    Exploration and exploitation in Indonesia now are still focused on conventional hydrocarbon energy than unconventional hydrocarbon energy such as shale gas. Tanjung Formation is a source rock of Barito Basin located in South Kalimantan that potentially as shale hydrocarbon. In this research, integrated methods using geochemical analysis, mineralogy, petrophysical analysis and seismic interpretation has been applied to explore the shale hydrocarbon potential in Barito Field for Tanjung formation. The first step is conducting geochemical and mineralogy analysis to the shale rock sample. Our analysis shows that the organic richness is ranging from 1.26-5.98 wt.% (good to excellent) with the depth of early mature window of 2170 m. The brittleness index is in an average of 0.44-0.56 (less Brittle) and Kerogen type is classified into II/III type that potentially produces oil and gas. The second step is continued by performing petrophysical analysis, which includes Total Organic Carbon (TOC) calculation and brittleness index continuously. The result has been validated with a laboratory measurement that obtained a good correlation. In addition, seismic interpretation based on inverted acoustic impedance is applied to map the distributions of shale hydrocarbon potential. Our interpretation shows that shale hydrocarbon potential is localized in the eastern and southeastern part of the study area.

  13. Mechanochemical Knoevenagel condensation investigated in situ

    Directory of Open Access Journals (Sweden)

    Sebastian Haferkamp

    2017-09-01

    Full Text Available The mechanochemical Knoevenagel condensation of malononitrile with p-nitrobenzaldehyde was studied in situ using a tandem approach. X-ray diffraction and Raman spectroscopy were combined to yield time-resolved information on the milling process. Under solvent-free conditions, the reaction leads to a quantitative conversion to p-nitrobenzylidenemalononitrile within 50 minutes. The in situ data indicate that the process is fast and proceeds under a direct conversion. After stopping the milling process, the reaction continues until complete conversion. The continuous and the stopped milling process both result in crystalline products suitable for single crystal X-ray diffraction.

  14. Resolving Key Uncertainties in Subsurface Energy Recovery: One Role of In Situ Experimentation and URLs (Invited)

    Science.gov (United States)

    Elsworth, D.

    2013-12-01

    Significant uncertainties remain and influence the recovery of energy from the subsurface. These uncertainties include the fate and transport of long-lived radioactive wastes that result from the generation of nuclear power and have been the focus of an active network of international underground research laboratories dating back at least 35 years. However, other nascent carbon-free energy technologies including conventional and EGS geothermal methods, carbon-neutral methods such as carbon capture and sequestration and the utilization of reduced-carbon resources such as unconventional gas reservoirs offer significant challenges in their effective deployment. We illustrate the important role that in situ experiments may play in resolving behaviors at extended length- and time-scales for issues related to chemical-mechanical interactions. Significantly, these include the evolution of transport and mechanical characteristics of stress-sensitive fractured media and their influence of the long-term behavior of the system. Importantly, these interests typically relate to either creating reservoirs (hydroshearing in EGS reservoirs, artificial fractures in shales and coals) or maintaining seals at depth where the permeating fluids may include mixed brines, CO2, methane and other hydrocarbons. Critical questions relate to the interaction of these various fluid mixtures and compositions with the fractured substrate. Important needs are in understanding the roles of key processes (transmission, dissolution, precipitation, sorption and dynamic stressing) on the modification of effective stresses and their influence on the evolution of permeability, strength and induced seismicity on the resulting development of either wanted or unwanted fluid pathways. In situ experimentation has already contributed to addressing some crucial issues of these complex interactions at field scale. Important contributions are noted in understanding the fate and transport of long-lived wastes

  15. Oil shale development and its environmental considerations

    Science.gov (United States)

    Stone, R.T.; Johnson, H.; Decora, A.

    1974-01-01

    The petroleum shortage recently experienced by many nations throughout the world has created an intense interest in obtaining new and supplemental energy sources. In the United States, this interest has been centered on oil shale. Any major action by the federal government having significant environmental effects requires compliance with the National Environmental Policy Act of 1969 (NEPA). Since most oil shale is found on federal lands, and since its development involves significant environmental impacts, leasing oil shale lands to private interests must be in compliance with NEPA. For oil shale, program planning began at approximately the same time that NEPA was signed into law. By structuring the program to permit a resource and technological inventory by industry and the federal agencies, the Department of the Interior was able simultaneously to conduct the environmental assessments required by the act. This required: 1. Clearly defined program objections; 2. An organization which could integrate public policy with diverse scientific disciplines and environmental concerns; and 3. Flexible decisionmaking to adjust to policy changes as well as to evolving interpretations on EPA as clarified by court decisions. This paper outlines the program, the organization structure that was created for this specific task, and the environmental concerns which were investigated. The success of the program has been demonstrated by meeting the requirements of NEPA, without court challenge, and by industry's acceptance of a leasing program that included the most stringent environmental protection provisions ever required. The need for energy development has spurred the acceptance of the program. However, by its awareness and willingness to meet the environmental challenges of the future, industry has shown a reasonable understanding of its commitments. The pros and cons of development were publicly considered in hearings and analyzed in the final environmental statement. This

  16. Process mining

    DEFF Research Database (Denmark)

    van der Aalst, W.M.P.; Rubin, V.; Verbeek, H.M.W.

    2010-01-01

    Process mining includes the automated discovery of processes from event logs. Based on observed events (e.g., activities being executed or messages being exchanged) a process model is constructed. One of the essential problems in process mining is that one cannot assume to have seen all possible...... behavior. At best, one has seen a representative subset. Therefore, classical synthesis techniques are not suitable as they aim at finding a model that is able to exactly reproduce the log. Existing process mining techniques try to avoid such “overfitting” by generalizing the model to allow for more...

  17. Leaching study of oil shale in Kentucky : with a section on Hydrologic reconnaissance of the oil shale outcrop in Kentucky

    Science.gov (United States)

    Leung, Samuel S.; Leist, D.W.; Davis, R.W.; Cordiviola, Steven

    1984-01-01

    Oil shales in Kentucky are rocks of predominantly Devonian age. The most prominant are the Ohio, Chattanooga, and New Albany Shales. A leaching study was done on six fresh oil shale samples and one retorted oil shale sample. Leaching reagents were distilled water, 0.0005 N sulfuric acid, and 0.05 N sulfuric acid. The concentration of constituents in the leachates were highly variable. The concentration of sodium, manganese, and zinc in the retorted shale leachate was several orders of magnitude higher than those of the leachates of fresh shale samples. The major oil shale outcrop covers approximately 1,000 square miles in a horseshoe pattern from Vanceburg, Lewis County , in the east, to Louisville, Jefferson County, in the west. The Kentucky, Red, and Licking Rivers cross the outcrop belt, the Rolling Fork River flows along the strike of the shale in the southwest part of the outcrop, and the Ohio River flows past the outcrop at the ends of the horseshoe. Oil shale does not appear to significantly alter the water quality of these streams. Oil shale is not an aquifer, but seeps and springs found in the shale indicate that water moves through it. Ground water quality is highly variable. (USGS)

  18. Preliminary state-of-the-art survey: mining techniques for salt and other rock types

    Energy Technology Data Exchange (ETDEWEB)

    1976-12-01

    This is a systematic review of the state-of-the-art of underground mining and excavation technology in the U.S. as applied to salt, limestone, shale, and granite. Chapter 2 covers the basic characteristics of these rock types, the most frequently used underground mining methods, shaft and slope entry construction, equipment, and safety and productivity data. Chapters 3 and 4 summarize underground salt and limestone mining in the U.S. Chapter 5 shows that large amounts of thick shale exist in the U.S., but little is mined. Chapter 6 discusses underground excavations into granite-type rocks. Suggestions are given in the last chapter for further study. (DLC)

  19. Paleozoic in situ spores and pollen. Lycopsida

    Czech Academy of Sciences Publication Activity Database

    Bek, Jiří

    2017-01-01

    Roč. 296, 1/6 (2017), s. 1-111 ISSN 0375-0299 R&D Projects: GA ČR GAP210/12/2053 Institutional support: RVO:67985831 Keywords : in situ spores * reproductive organs * Lycopsida * Paleozoic Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.333, year: 2016

  20. In Situ Flash Pyrolysis of Straw

    DEFF Research Database (Denmark)

    Bech, Niels

    aske og reducere logistikomkostningerne ville gøre denne alternative energikilde betydelig mere attraktiv. Disse mål kan nås med in situ flash pyrolyse, hvor halm bliver omdannet til bio-olie i marken og koks efterlades på jorden for at forbedre jordstrukturen og tilføre mineraler. Hovedformålene med...

  1. Carcinoma in situ in the testis

    DEFF Research Database (Denmark)

    Rørth, M; Rajpert-De Meyts, E; Andersson, L

    2000-01-01

    Carcinoma in situ (CIS) of the testis is a common precursor of germ-cell tumours in adults and adolescents, with the exception of spermatocytic seminoma. This article reviews existing knowledge on the pathobiology, genetic aspects and epidemiology of CIS, discusses current hypotheses concerning...

  2. Treatment options for carcinoma in situ testis

    DEFF Research Database (Denmark)

    Mortensen, M S; Gundgaard, M.G.; Daugaard, G

    2011-01-01

    Carcinoma in situ testis (CIS) is known as the precursor of germ cell cancer of the testis. International guidelines on diagnosis and treatment are inconsistent. Some countries offer routine biopsies of the contralateral testicle in relation to orchidectomy for testicular cancer, whereas other...... their androgen status measured on a regular basis to find those cases where hormone substitution is needed....

  3. IN SITU MEASUREMENTS OF THE ACOUSTIC TARGET ...

    African Journals Online (AJOL)

    The acoustic target strength (TS) of Cape horse mackerel Trachurus trachurus capensis was measured in situ at 38 kHz during two surveys over the Namibian continental shelf in 1998 and 1999 using a SIMRAD EK500 echosounder/ES38D submersible split-beam transducer. Scattered aggregations of horse mackerel ...

  4. FROM DATA MINING TO BEHAVIOR MINING

    OpenAIRE

    ZHENGXIN CHEN

    2006-01-01

    Knowledge economy requires data mining be more goal-oriented so that more tangible results can be produced. This requirement implies that the semantics of the data should be incorporated into the mining process. Data mining is ready to deal with this challenge because recent developments in data mining have shown an increasing interest on mining of complex data (as exemplified by graph mining, text mining, etc.). By incorporating the relationships of the data along with the data itself (rathe...

  5. Social big data mining

    CERN Document Server

    Ishikawa, Hiroshi

    2015-01-01

    Social Media. Big Data and Social Data. Hypotheses in the Era of Big Data. Social Big Data Applications. Basic Concepts in Data Mining. Association Rule Mining. Clustering. Classification. Prediction. Web Structure Mining. Web Content Mining. Web Access Log Mining, Information Extraction and Deep Web Mining. Media Mining. Scalability and Outlier Detection.

  6. Malignant human cell transformation of Marcellus Shale gas drilling flow back water.

    Science.gov (United States)

    Yao, Yixin; Chen, Tingting; Shen, Steven S; Niu, Yingmei; DesMarais, Thomas L; Linn, Reka; Saunders, Eric; Fan, Zhihua; Lioy, Paul; Kluz, Thomas; Chen, Lung-Chi; Wu, Zhuangchun; Costa, Max; Zelikoff, Judith

    2015-10-01

    The rapid development of high-volume horizontal hydraulic fracturing for mining natural gas from shale has posed potential impacts on human health and biodiversity. The produced flow back waters after hydraulic stimulation are known to carry high levels of saline and total dissolved solids. To understand the toxicity and potential carcinogenic effects of these wastewaters, flow back waters from five Marcellus hydraulic fracturing oil and gas wells were analyzed. The physicochemical nature of these samples was analyzed by inductively coupled plasma mass spectrometry and scanning electron microscopy/energy dispersive X-ray spectroscopy. A cytotoxicity study using colony formation as the endpoint was carried out to define the LC50 values of test samples using human bronchial epithelial cells (BEAS-2B). The BEAS-2B cell transformation assay was employed to assess the carcinogenic potential of the samples. Barium and strontium were among the most abundant metals in these samples and the same metals were found to be elevated in BEAS-2B cells after long-term treatment. BEAS-2B cells treated for 6weeks with flow back waters produced colony formation in soft agar that was concentration dependent. In addition, flow back water-transformed BEAS-2B cells show better migration capability when compared to control cells. This study provides information needed to assess the potential health impact of post-hydraulic fracturing flow back waters from Marcellus Shale natural gas mining. Copyright © 2015 Elsevier Inc. All rights reserved.

  7. In Situ Remediation Integrated Program: Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    The In Situ Remediation Integrated Program (ISR IP) was instituted out of recognition that in situ remediation could fulfill three important criteria: significant cost reduction of cleanup by eliminating or minimizing excavation, transportation, and disposal of wastes; reduced health impacts on workers and the public by minimizing exposure to wastes during excavation and processing; and remediation of inaccessible sites, including: deep subsurfaces, in, under, and around buildings. Buried waste, contaminated soils and groundwater, and containerized wastes are all candidates for in situ remediation. Contaminants include radioactive wastes, volatile and non-volatile organics, heavy metals, nitrates, and explosive materials. The ISR IP intends to facilitate development of in situ remediation technologies for hazardous, radioactive, and mixed wastes in soils, groundwater, and storage tanks. Near-term focus is on containment of the wastes, with treatment receiving greater effort in future years. ISR IP is an applied research and development program broadly addressing known DOE environmental restoration needs. Analysis of a sample of 334 representative sites by the Office of Environmental Restoration has shown how many sites are amenable to in situ remediation: containment--243 sites; manipulation--244 sites; bioremediation--154 sites; and physical/chemical methods--236 sites. This needs assessment is focused on near-term restoration problems (FY93--FY99). Many other remediations will be required in the next century. The major focus of the ISR EP is on the long term development of permanent solutions to these problems. Current needs for interim actions to protect human health and the environment are also being addressed.

  8. Effects of Hydraulic Frac Fluids on Subsurface Microbial Communities in Gas Shales

    Science.gov (United States)

    Jiménez, Núria; Krüger, Martin

    2014-05-01

    Shale gas is being considered as a complementary energy resource to coal or other fossil fuels. The exploitation of unconventional gas reservoirs requires the use of advanced drilling techniques and hydraulic stimulation (fracking). During fracking operations, large amounts of fluids (fresh water, proppants and chemical additives) are injected at high pressures into the formations, to produce fractures and fissures, and thus to release gas from the source rock into the wellbore. The injected fluids partly remain in the formation, while about 20 to 40% of the originally injected fluid flows back to the surface, together with formation waters, sometimes containing dissolved hydrocarbons, high salt concentrations, etc. The overall production operation will likely affect and be affected by subsurface microbial communities associated to the shale formations. On the one hand microbial activity (like growth, biofilm formation) can cause unwanted processes like corrosion, clogging, etc. On the other hand, the introduction of frac fluids could either enhance microbial growth or cause toxicity to the shale-associated microbial communities. To investigate the potential impacts of changing environmental reservoir conditions, like temperature, salinity, oxgen content and pH, as well as the introduction of frac or geogenic chemicals on subsurface microbial communities, laboratory experiments under in situ conditions (i.e. high temperatures and pressures) are being conducted. Enrichment cultures with samples from several subsurface environments (e.g. shale and coal deposits, gas reservoirs, geothermal fluids) have been set up using a variety of carbon sources, including hydrocarbons and typical frac chemicals. Classical microbiological and molecular analysis are used to determine changes in the microbial abundance, community structure and function after the exposure to different single frac chemicals, "artificial" frac fluids or production waters. On the other hand, potential

  9. Shale gas development impacts on surface water quality in Pennsylvania.

    Science.gov (United States)

    Olmstead, Sheila M; Muehlenbachs, Lucija A; Shih, Jhih-Shyang; Chu, Ziyan; Krupnick, Alan J

    2013-03-26

    Concern has been raised in the scientific literature about the environmental implications of extracting natural gas from deep shale formations, and published studies suggest that shale gas development may affect local groundwater quality. The potential for surface water quality degradation has been discussed in prior work, although no empirical analysis of this issue has been published. The potential for large-scale surface water quality degradation has affected regulatory approaches to shale gas development in some US states, despite the dearth of evidence. This paper conducts a large-scale examination of the extent to which shale gas development activities affect surface water quality. Focusing on the Marcellus Shale in Pennsylvania, we estimate the effect of shale gas wells and the release of treated shale gas waste by permitted treatment facilities on observed downstream concentrations of chloride (Cl(-)) and total suspended solids (TSS), controlling for other factors. Results suggest that (i) the treatment of shale gas waste by treatment plants in a watershed raises downstream Cl(-) concentrations but not TSS concentrations, and (ii) the presence of shale gas wells in a watershed raises downstream TSS concentrations but not Cl(-) concentrations. These results can inform future voluntary measures taken by shale gas operators and policy approaches taken by regulators to protect surface water quality as the scale of this economically important activity increases.

  10. Water management practices used by Fayetteville shale gas producers.

    Energy Technology Data Exchange (ETDEWEB)

    Veil, J. A. (Environmental Science Division)

    2011-06-03

    Water issues continue to play an important role in producing natural gas from shale formations. This report examines water issues relating to shale gas production in the Fayetteville Shale. In particular, the report focuses on how gas producers obtain water supplies used for drilling and hydraulically fracturing wells, how that water is transported to the well sites and stored, and how the wastewater from the wells (flowback and produced water) is managed. Last year, Argonne National Laboratory made a similar evaluation of water issues in the Marcellus Shale (Veil 2010). Gas production in the Marcellus Shale involves at least three states, many oil and gas operators, and multiple wastewater management options. Consequently, Veil (2010) provided extensive information on water. This current study is less complicated for several reasons: (1) gas production in the Fayetteville Shale is somewhat more mature and stable than production in the Marcellus Shale; (2) the Fayetteville Shale underlies a single state (Arkansas); (3) there are only a few gas producers that operate the large majority of the wells in the Fayetteville Shale; (4) much of the water management information relating to the Marcellus Shale also applies to the Fayetteville Shale, therefore, it can be referenced from Veil (2010) rather than being recreated here; and (5) the author has previously published a report on the Fayetteville Shale (Veil 2007) and has helped to develop an informational website on the Fayetteville Shale (Argonne and University of Arkansas 2008), both of these sources, which are relevant to the subject of this report, are cited as references.

  11. In-situ coal gasification as a progressive coal utilization method

    Energy Technology Data Exchange (ETDEWEB)

    Petrenko, E.V.; Saltykov, I.F.

    1988-02-01

    Describes the Podzemgaz coal gasification station at Angren that was put into operation in 1961. It exploits a 15 m thick and 120-250 m deep seam of brown coal. Technology of in-situ coal gasification is described and its results are compared in regard to cost and efficiency with the results of conventional surface mining. Air blowing is used for most in-situ coal gasification in USSR. Trials using air enriched in oxygen for this purpose were conducted in 1953 and 1957 but did not find wider application. A station using oxygen enrichment technology is planned for Angren at the Apartak section, as cheaper oxygen production methods have emerged. A new concept for in-situ coal gasification using membrane technology (molecular sieves) is set out. This technology assures total chemical and power utilization of coal, yielding not only coal gas but also liquid nitrogen, hydrogen, a mixture of both these gases for ammonia production, and carbonic acid. Prospective site selection for in-situ coal gasification stations is discussed and conditions required for the respective coalfields are outlined.

  12. Quantifying shale weathering by Li isotopes at the Susquehanna Shale Hills Critical Zone Observatory

    Science.gov (United States)

    Steinhoefel, Grit; Fantle, Matthew S.; Brantley, Sue L.

    2017-04-01

    Lithium isotopes have emerged as a powerful tool to investigate abiotic weathering processes because isotope fraction is controlled by silicate weathering depending on the weathering rate. In this study, we explore Li isotopes as a proxy for shale weathering in the well-investigated Susquehanna Shale Hills Critical Zone Observatory (USA), which is a first-order catchment in a temperate climate in the Appalachian Mountain. Groundwater, soil and stream water reveal large variation in δ7Li (14.5 to 40.0‰) controlled by variable but high degrees of Li retention by kaolinite and vermiculite formation. Parental shales, bulk soils and stream sediments reveal similar isotope signatures with little variations giving average δ7Li values of -0.6, 0.5 and -0.3‰, respectively which is in the typical range for shales dominated by structural-bound Li and consistent with high Li retention. An isotope mass balance approach reveal that Li is virtually quantitatively exported by erosional weathering from the system. This result is consisted with a high depletion of Li along with clay minerals in soils whereas both is enriched in stream sediments. Overall shale weathering is dominated by clay transformation forming kaolinite through intermediate phases under highly incongruent weathering conditions followed by preferentially loss of fine-grained weathering products, a processes which is likely an important mechanism in the modern global Li cycle.

  13. The technology of extracting gaseous fuel based on comprehensive in situ gasification and coalbed degassing

    Directory of Open Access Journals (Sweden)

    А. Н. Шабаров

    2016-08-01

    Full Text Available The study considers a comprehensive technology (designed and patented by the authors of developing coal and methane deposits which combines in situ gasification of lower coalbeds in the suite of rock bump hazardous gassy beds, extraction of coal methane and mechanized mining of coal. The first stage of the technology consists in mining gaseous fuel that enables one to extract up to 15-20 % of total energy from the suite of coalbeds. Geodynamic zoning is used to select positions for boring wells. Using the suggested technology makes it possible to solve a number of tasks simultaneously. First of all that is extracting gaseous fuel from the suite of coalbeds without running any mining works while retaining principal coalbeds in the suite and preparing them for future processing (unloading and degassing. During the first phase the methane-coal deposit works as a gas deposit only, the gas having two sources – extracted methane (which includes its locked forms, absorbed and adsorbed and the products of partial incineration of thin coalbeds, riders and seams from thee suite. The second stage consists in deep degassing and unloading of coal beds which sharply reduces the hazards of methane explosion and rock bumps, thus increasing the productivity of mechanized coal mining. During the second stage coal is mined in long poles with the account of degassing and unloading of coal beds, plus the data on gas dynamic structure of coal rock massif.

  14. Annual report for fiscal 1995, Kamaishi in-situ experiments (phase 2)

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, Kazuhiro; Araki, Ryusuke; Koide, Kaoru; Sawada, Atsushi; Shimizu, Isao; Fujita, Asao; Yoshida, Eiichi [Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan)

    1996-04-01

    The Kamaishi in-situ experiments (Phase 2) have strived to ascertain geological characteristics of the deep underground and the various phenomenon occurring therein and to improve technologies and methodologies required for such studies since fiscal 1993. Fiscal 1995 is the third year of Phase 2. The in-situ experiments are conducted at the northern most end of the Kamaishi mine in order to minimize the effect of the already excavated drifts totaling approximately 140 km long. The studies are conducted in Kurihashi granodiorite of Early Cretaceous widely distributed in this area. Major activities performed in this fiscal year are summarized below: (1) TASK 1 (Characterization of the deep underground geological environment). (2) TASK 2 (Study of excavation disturbance in fractured rock). (3) TASK 3 (Study of groundwater flow and solute transport in crystalline rock). (4) TASK 4 (Study of engineered barrier). (5) TASK 5 (Study of earthquakes). (J.P.N.)

  15. Borehole radar system for South African gold and platinum mines

    CSIR Research Space (South Africa)

    Vogt, D

    2006-12-01

    Full Text Available for South African gold and platinum mines Declan Vogt CSIR, PO Box 91230, Auckland Park, 2006 e-mail: clvogt@csir.co.za © 2006 December Geological Society of South Africa ABSTRACT Borehole radar is an electromagnetic tool that can be applied to assist... with marker horizons. For example, the Carbon Leader is overlain by the Green Bar Shale (Schweitzer and Johnson, 1997). SOUTH AFRICAN JOURNAL OF GEOLOGY, 2006, VOLUME 109 PAGB 521-528 522 A BOREHOLE RADAR SYSTEM EOR SOUTH AFRICAN GOLD AND PLATINUM MINES a...

  16. Environmental contamination due to shale gas development.

    Science.gov (United States)

    Annevelink, M P J A; Meesters, J A J; Hendriks, A J

    2016-04-15

    Shale gas development potentially contaminates both air and water compartments. To assist in governmental decision-making on future explorations, we reviewed scattered information on activities, emissions and concentrations related to shale gas development. We compared concentrations from monitoring programmes to quality standards as a first indication of environmental risks. Emissions could not be estimated accurately because of incomparable and insufficient data. Air and water concentrations range widely. Poor wastewater treatment posed the highest risk with concentrations exceeding both Natural Background Values (NBVs) by a factor 1000-10,000 and Lowest Quality Standards (LQSs) by a factor 10-100. Concentrations of salts, metals, volatile organic compounds (VOCs) and hydrocarbons exceeded aquatic ecotoxicological water standards. Future research must focus on measuring aerial and aquatic emissions of toxic chemicals, generalisation of experimental setups and measurement technics and further human and ecological risk assessment. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Modeling an oil shale fluid bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    Vasalos, I.A.; Lefkopoulos, A.; Georgiadou, M.

    1988-02-01

    Oil shale retorting involves heating of solid particles and pyrolysis of the organic matter to produce hydrocarbon liquid shale oil. During the pyrolysis process, part of the organic material remains in the inorganic matrix as coke residue. Combustion of the coke residue can provide the energy necessary for retorting. In this paper the use of a fluid bed combustor to burn the coke residue is examined. The basis for predicting the performance of the fluid bed combustor is the application of the two-phase theory of fluidization. The carbon burning efficiency was calculated as a function of temperature, pressure, and bubble size. For the same conditions, the carbonate decomposition and the associated energy loss were also established. Conditions were found which make feasible complete carbon combustion with minimum carbonate decomposition.

  18. Modeling an oil shale fluid bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    Vasalos, I.A.; Lefkopoulos, A.; Georgiadou, M.

    1985-01-01

    Oil shale retorting involves heating of solid particles and pyrolysis of the organic matter to produce hydrocarbon liquid--shale oil. During the pyrolysis process part of the organic material remains in the inorganic matrix as coke residue. Combustion of the coke residue can provide the energy necessary for retorting. In this paper the use of a fluid bed combustor to burn the coke residue is examined. The basis for predicting the performance of the fluid bed combustor is the application of the two-phase theory of fluidization. The carbon burning efficiency was calculated as a function of temperature, pressure, and bubble size. For the same conditions the carbonate decomposition and the associated energy loss was also established.

  19. Oxygen compounds in the Irati Shale oil

    Energy Technology Data Exchange (ETDEWEB)

    Alfonso, J.C.; Schmal, M. (Federal Univ. of Rio de Janeiro, COPPE/EQ/UFRJ, C.P. 68502, 21945 Rio de Janeiro (Brazil)); Cardoso, J.N. (Inst. of Chemistry/UFRJ, Centro de Technologia, Bloco A, Sala A-603, 21901 Rio de Janeiro (Brazil))

    1992-04-01

    This paper reports the principal alkylphenols (4 wt %) and carboxylic acids (1.2 wt %) present in the Irati Shale oil S[tilde a]o Mateus do Sul, Paran acute (a) by means of a combination of gas chromatography-mass spectrometry (GC-MS) and retention time-data of standard compounds. it appears that the phenols are essentially monocyclic in nature with methyl groups as the main substituents. Carboxylic acids are principally linear and predominantly of the range C[sub 14]--C[sub 20]. After catalytic hydrotreatment (400 [degrees]C, 125 atm) high hydrodeoxygenation levels were obtained (87 wt %) for phenols and carboxylic acids, although the relative distribution of the various compounds was not significantly changed. Oxygen is present in the carbonaceous residue as several functionalities xanthenes, phenols, aryl ethers, carbonyl compounds, and furanic structures. The remaining acidic compounds may cause instability of the treated shale oil.

  20. Steam pyrolysis of shale oil vacuum distillates for petrochemical intermediates production

    Energy Technology Data Exchange (ETDEWEB)

    Smith, P.D.; Dickson, P.F.; Yesavage, V.F.

    1978-03-01

    Vacuum distillations of shale oil may be worthwhile since it produces a good steam pyrolysis feedstock. Maximum ethylene yield was 28.8% for the simulated in situ distillate and 22.6% for the Tosco II distillate. Yields are as good or better than those obtainable from conventional feedstocks. Severity of cracking is increased by increasing the residence time and temperature. The effect of steam to hydrocarbon ratio cannot be determined from the data. Trends observed with increasing severity were: (a) ethylene yield rises to a maximum, then slowly decreases; (b) propylene and butadiene yields continually decrease; (c) methane and hydrogen yields increase; (d) weight percent solids increased. Short residence times, in general, give the highest yields of valuable components. 2 tables, 4 figs.

  1. Shale and the US Economy: Three Counterfactuals

    OpenAIRE

    Arora, Vipin

    2017-01-01

    I use three different—and simple—counterfactuals to approximate the real GDP and employment effects of US oil and gas production from shale over the 2011 to 2015 period. Real GDP growth would have been 0.7 to 0.2 percentage points lower on average each year over that period without such increases; employment growth 0.5 to 0.1 percentage points lower.

  2. Generic Argillite/Shale Disposal Reference Case

    OpenAIRE

    Zheng, Liange

    2014-01-01

    Radioactive waste disposal in a deep subsurface repository hosted in clay/shale/argillite is a subject of widespread interest given the desirable isolation properties, geochemically reduced conditions, and widespread geologic occurrence of this rock type (Hansen 2010; Bianchi et al. 2013). Bianchi et al. (2013) provides a description of diffusion in a clay-hosted repository based on single-phase flow and full saturation using parametric data from documented studies in Europe (e.g., ANDRA 2005...

  3. Comparative study on direct burning of oil shale and coal

    Science.gov (United States)

    Hammad, Ahmad; Al Asfar, Jamil

    2017-07-01

    A comparative study of the direct burning processes of oil shale and coal in a circulating fluidized bed (CFB) was done in this study using ANSYS Fluent software to solve numerically the governing equations of continuity, momentum, energy and mass diffusion using finite volume method. The model was built based on an existing experimental combustion burner unit. The model was validated by comparing the theoretical results of oil shale with proved experimental results from the combustion unit. It was found that the temperature contours of the combustion process showed that the adiabatic flame temperature was 1080 K for oil shale compared with 2260 K for coal, while the obtained experimental results of temperatures at various locations of burner during the direct burning of oil shale showed that the maximum temperature reached 962 K for oil shale. These results were used in economic and environmental analysis which show that oil shale may be used as alternative fuel for coal in cement industry in Jordan.

  4. Shale gas. Opportunities and challenges for European energy markets

    Energy Technology Data Exchange (ETDEWEB)

    De Joode, J.; Plomp, A.J.; Ozdemir, O. [ECN Policy Studies, Petten (Netherlands)

    2013-02-15

    The outline of the presentation shows the following elements: Introduction (Shale gas revolution in US and the situation in the EU); What could be the impact of potential shale gas developments on the European gas market?; How may shale gas developments affect the role of gas in the transition of the power sector?; and Key messages. The key messages are (1) Prospects for European shale gas widely differ from US case (different reserve potential, different competition, different market dynamics); (2) Shale gas is unlikely to be a game changer in Europe; and (3) Impact of shale gas on energy transition in the medium and long term crucially depends on gas vs. coal prices and the 'penalty' on CO2 emissions.

  5. Plan for addressing issues relating to oil shale plant siting

    Energy Technology Data Exchange (ETDEWEB)

    Noridin, J. S.; Donovan, R.; Trudell, L.; Dean, J.; Blevins, A.; Harrington, L. W.; James, R.; Berdan, G.

    1987-09-01

    The Western Research Institute plan for addressing oil shale plant siting methodology calls for identifying the available resources such as oil shale, water, topography and transportation, and human resources. Restrictions on development are addressed: land ownership, land use, water rights, environment, socioeconomics, culture, health and safety, and other institutional restrictions. Descriptions of the technologies for development of oil shale resources are included. The impacts of oil shale development on the environment, socioeconomic structure, water availability, and other conditions are discussed. Finally, the Western Research Institute plan proposes to integrate these topics to develop a flow chart for oil shale plant siting. Western Research Institute has (1) identified relative topics for shale oil plant siting, (2) surveyed both published and unpublished information, and (3) identified data gaps and research needs. 910 refs., 3 figs., 30 tabs.

  6. Geomechanical Properties of Unconventional Shale Reservoirs

    Directory of Open Access Journals (Sweden)

    Mohammad O. Eshkalak

    2014-01-01

    Full Text Available Production from unconventional reservoirs has gained an increased attention among operators in North America during past years and is believed to secure the energy demand for next decades. Economic production from unconventional reservoirs is mainly attributed to realizing the complexities and key fundamentals of reservoir formation properties. Geomechanical well logs (including well logs such as total minimum horizontal stress, Poisson’s ratio, and Young, shear, and bulk modulus are secured source to obtain these substantial shale rock properties. However, running these geomechanical well logs for the entire asset is not a common practice that is associated with the cost of obtaining these well logs. In this study, synthetic geomechanical well logs for a Marcellus shale asset located in southern Pennsylvania are generated using data-driven modeling. Full-field geomechanical distributions (map and volumes of this asset for five geomechanical properties are also created using general geostatistical methods coupled with data-driven modeling. The results showed that synthetic geomechanical well logs and real field logs fall into each other when the input dataset has not seen the real field well logs. Geomechanical distributions of the Marcellus shale improved significantly when full-field data is incorporated in the geostatistical calculations.

  7. A new stalked filter-feeder from the middle Cambrian Burgess Shale, British Columbia, Canada.

    Directory of Open Access Journals (Sweden)

    Lorna J O'Brien

    Full Text Available Burgess Shale-type deposits provide invaluable insights into the early evolution of body plans and the ecological structure of Cambrian communities, but a number of species, continue to defy phylogenetic interpretations. Here we extend this list to include a new soft-bodied animal, Siphusauctum gregarium n. gen. and n. sp., from the Tulip Beds (Campsite Cliff Shale Member, Burgess Shale Formation of Mount Stephen (Yoho National Park, British Columbia. With 1,133 specimens collected, S. gregarium is clearly the most abundant animal from this locality.This stalked animal (reaching at least 20 cm in length, has a large ovoid calyx connected to a narrow bilayered stem and a small flattened or bulb-like holdfast. The calyx is enclosed by a flexible sheath with six small openings at the base, and a central terminal anus near the top encircled by indistinct openings. A prominent organ, represented by six radially symmetrical segments with comb-like elements, surrounds an internal body cavity with a large stomach, conical median gut and straight intestine. Siphusauctum gregarium was probably an active filter-feeder, with water passing through the calyx openings, capturing food particles with its comb-like elements. It often occurs in large assemblages on single bedding planes suggesting a gregarious lifestyle, with the animal living in high tier clusters. These were probably buried en masse more or less in-situ by rapid mud flow events.Siphusauctum gregarium resembles Dinomischus, another Cambrian enigmatic stalked animal. Principal points of comparison include a long stem with a calyx containing a visceral mass and bract-like elements, and a similar lifestyle albeit occupying different tiering levels. The presence in both animals of a digestive tract with a potential stomach and anus suggest a grade of organization within bilaterians, but relationships with extant phyla are not straightforward. Thus, the broader affinities of S. gregarium remain

  8. In-Situ Planetary Chemical Analysis

    Science.gov (United States)

    Kounaves, S. P.; Buehler, M. G.; Grannan, S. M.; Hecht, M. H.; Kuhlman, K. R.

    2000-07-01

    Both, the search for evidence of life on Mars and the assessment of the Martian environment in respect to its compatibility with human explorers, will require the ability to measure and understand the aqueous chemistry of the Martian regolith. Direct in-situ chemical analysis is the only method by which chemical biosignatures can be reliably recognized and the toxicity of the regolith accurately assessed. Qualitative and quantitative determination of the aqueous ionic constituents and their concentrations is critical in developing kinetic and thermodynamic models that can be used to accurately predict the potential of the past or present Martian geochemical environment to have either generated or still sustain life. In-situ chemical characterization could provide evidence as to whether the chemical composition of the regolith or evaporates in suspected ancient water bodies have been biologically influenced.

  9. Military Fuels Refined from Paraho-II Shale Oil.

    Science.gov (United States)

    1981-03-01

    Laboratories showed that growth of Cladosporium resinae was supported by the shale-derived JP-5 and DFM. 1t The performances of shale fuels in a turbine...27 11 Corrosion Tendencies of Shale Fuels ............................. 28 12 Growth Rating of Cladosporium Resinae in Tubes After Days of...screw cap test tubes and overlayed with 3 ml of the test fuel. Each tube was inoculated with one drop of a spore suspension of Cladosporium resinae , QM

  10. Optimal Pretreatment System of Flowback Water from Shale Gas Production

    OpenAIRE

    Carrero-Parreño, Alba; Onishi, Viviani C.; Salcedo Díaz, Raquel; Ruiz-Femenia, Rubén; Fraga, Eric S.; Caballero, José A.; Reyes-Labarta, Juan A.

    2017-01-01

    Shale gas has emerged as a potential resource to transform the global energy market. Nevertheless, gas extraction from tight shale formations is only possible after horizontal drilling and hydraulic fracturing, which generally demand large amounts of water. Part of the ejected fracturing fluid returns to the surface as flowback water, containing a variety of pollutants. For this reason, water reuse and water recycling technologies have received further interest for enhancing overall shale gas...

  11. Fugitive Emissions from the Bakken Shale Illustrate Role of Shale Production in Global Ethane Shift

    Science.gov (United States)

    Kort, E. A.; Smith, M. L.; Murray, L. T.; Gvakharia, A.; Brandt, A. R.; Peischl, J.; Ryerson, T. B.; Sweeney, C.; Travis, K.

    2016-01-01

    Ethane is the second most abundant atmospheric hydrocarbon, exerts a strong influence on tropospheric ozone, and reduces the atmosphere's oxidative capacity. Global observations showed declining ethane abundances from 1984 to 2010, while a regional measurement indicated increasing levels since 2009, with the reason for this subject to speculation. The Bakken shale is an oil and gas-producing formation centered in North Dakota that experienced a rapid increase in production beginning in 2010. We use airborne data collected over the North Dakota portion of the Bakken shale in 2014 to calculate ethane emissions of 0.23 +/- 0.07 (2 sigma) Tg/yr, equivalent to 1-3% of total global sources. Emissions of this magnitude impact air quality via concurrent increases in tropospheric ozone. This recently developed large ethane source from one location illustrates the key role of shale oil and gas production in rising global ethane levels.

  12. Fugitive emissions from the Bakken shale illustrate role of shale production in global ethane shift

    Science.gov (United States)

    Kort, E. A.; Smith, M. L.; Murray, L. T.; Gvakharia, A.; Brandt, A. R.; Peischl, J.; Ryerson, T. B.; Sweeney, C.; Travis, K.

    2016-05-01

    Ethane is the second most abundant atmospheric hydrocarbon, exerts a strong influence on tropospheric ozone, and reduces the atmosphere's oxidative capacity. Global observations showed declining ethane abundances from 1984 to 2010, while a regional measurement indicated increasing levels since 2009, with the reason for this subject to speculation. The Bakken shale is an oil and gas-producing formation centered in North Dakota that experienced a rapid increase in production beginning in 2010. We use airborne data collected over the North Dakota portion of the Bakken shale in 2014 to calculate ethane emissions of 0.23 ± 0.07 (2σ) Tg/yr, equivalent to 1-3% of total global sources. Emissions of this magnitude impact air quality via concurrent increases in tropospheric ozone. This recently developed large ethane source from one location illustrates the key role of shale oil and gas production in rising global ethane levels.

  13. Surface Mines, Other - Longwall Mining Panels

    Data.gov (United States)

    NSGIC Education | GIS Inventory — Coal mining has occurred in Pennsylvania for over a century. A method of coal mining known as Longwall Mining has become more prevalent in recent decades. Longwall...

  14. In situ health monitoring of piezoelectric sensors

    Science.gov (United States)

    Jensen, Scott L. (Inventor); Drouant, George J. (Inventor)

    2013-01-01

    An in situ health monitoring apparatus may include an exciter circuit that applies a pulse to a piezoelectric transducer and a data processing system that determines the piezoelectric transducer's dynamic response to the first pulse. The dynamic response can be used to evaluate the operating range, health, and as-mounted resonance frequency of the transducer, as well as the strength of a coupling between the transducer and a structure and the health of the structure.

  15. Electrocrystallisation studied in situ by optical scattering

    Science.gov (United States)

    Rönnow, R.; Isidorsson, J.

    1996-12-01

    Optical scattering was measured in situ on an electrochromic tin oxide film during coulometric titration in an electrolyte of 1 M LiClO 4 in propylene carbonate. The normalised scattering increased at the critical point where electrocrystallisation started, according to optical and electrochemical results. A lower potential limit of 1.2V vs Li was established for tin oxide in electrochromic applications. Electrocrystallisation takes place below this limit.

  16. Squamous cell carcinoma in situ after irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kambara, Takeshi; Nishiyama, Takafumi; Yamada, Rie; Nagatani, Tetsuo; Nakajima, Hiroshi [Yokohama City Univ. (Japan). School of Medicine; Sugiyama, Asami

    1997-12-31

    We report two cases with Squamous Cell Carcinoma (SCC) in situ caused by irradiation to hand eczemas, resistant to any topical therapies. Both of our cases clinically show palmer sclerosis and flexor restriction of the fingers, compatible to chronic radiation dermatitis. Although SCC arising in chronic radiation dermatitis is usually developed ten to twenty years after irradiation, in our cases SCC were found more than forty years after irradiation. (author)

  17. The South Manchurian Railway Company and the Mining Industry: The Case of the Fushun Coal Mine

    Directory of Open Access Journals (Sweden)

    Tsu-yu Chen

    2015-09-01

    Full Text Available Following the Japanese victory over Czarist Russia in the Russo-Japanese War and the signing of the Treaty of Portsmouth in 1905, the southernmost section of the southern branch of the China Far East Railway (Changchun–Port Arthur was transferred to Japanese control. A new, semi-privately held company, the South Manchuria Railway Company (SMR, Mantetsu, was established with 85.6 percent capitalization by the Japanese government and foreign bonds to operate the railroad and to develop settlements (including highways, public health facilities, educational institutions, and industries (coal mines, harbor facilities, electrical power plants, shale oil plants, chemical plants, and restaurants along its route. SMR nonetheless emphasized railway and mining investment. The centerpiece of its mining interests was the Fushun Coal Mine. Starting in 1917, SMR began to prosper, with most profits coming from its coal mines, and it soon spun off subsidiary companies. In this sense, although the factors that influenced development of the Fushun Coal Mine in each period were different, this development still shows continuity of the business management.

  18. Ectasia after laser in situ keratomileusis.

    Science.gov (United States)

    Rabinowitz, Yaron S

    2006-10-01

    The potential for litigation has resulted in increased interest in ectasia after laser in situ keratomileusis. This article summarizes papers written during this past year on this subject. A panel of refractive surgery experts have summarized the current state of knowledge on this subject and provided guidelines to minimize risk. Because ectasia may occur in the absence of risk factors, there may be corneas with biomechanical factors not detectable with present technology which are at risk. Several articles point out the limitations of the Orbscan (Bausch & Lomb, Rochester, New York, USA), in particular its accuracy and reproducibility with regard to data generated from the posterior surface of the cornea. A biomechanical model of the cornea is proposed which suggests that each cornea's response to laser in situ keratomileusis is unique. Several case reports are also reviewed which provide insight into pathogenesis and potential new treatment options; these include reports on histopathology, topographic pseudokeratectasia, ectasia from transient raised intraocular pressure, poor response to laser in situ keratomileusis after incisional surgery, intracorneal rings, collagen cross-linking and conductive keratoplasty to stabilize and sphericize the cornea with ectasia. Our knowledge about ectasia is still in evolution. Insights into the biomechanics and genetics of the cornea may allow us to further reduce its occurrence.

  19. In Situ Measurement of Aerosol Extinction

    Science.gov (United States)

    Strawa, Anthony W.; Castaneda, R.; Owano, T. G.; Bear, D.; Gore, Warren J. (Technical Monitor)

    2001-01-01

    Aerosols are important contributors to the radiative forcing in the atmosphere. Much of the uncertainty in our knowledge of climate forcing is due to uncertainties in the radiative forcing due to aerosols as illustrated in the IPCC reports of the last ten years. Improved measurement of aerosol optical properties, therefore, is critical to an improved understanding of atmospheric radiative forcing. Additionally, attempts to reconcile in situ and remote measurements of aerosol radiative properties have generally not been successful. This is due in part to the fact that it has been impossible to measure aerosol extinction in situ in the past. In this presentation we introduce a new instrument that employs the techniques used in cavity ringdown spectroscopy to measure the aerosol extinction and scattering coefficients in situ. A prototype instrument has been designed and tested in the lab and the field. It is capable of measuring aerosol extinction coefficient to 2x10(exp -6) per meter. This prototype instrument is described and results are presented.

  20. Thermal evolution and shale gas potential estimation of the Wealden and Posidonia Shale in NW-Germany and the Netherlands: A 3D basin modelling study

    NARCIS (Netherlands)

    Bruns, B.; Littke, R.; Gasparik, M.; Wees, J.D. van; Nelskamp, S.

    2016-01-01

    Sedimentary basins in NW-Germany and the Netherlands represent potential targets for shale gas exploration in Europe due to the presence of Cretaceous (Wealden) and Jurassic (Posidonia) marlstones/shales as well as various Carboniferous black shales. In order to assess the regional shale gas

  1. Thermal evolution and shale gas potential estimation of the Wealden and Posidonia Shale in NW-Germany and the Netherlands : a 3D basin modelling study

    NARCIS (Netherlands)

    Bruns, B.; Littke, R.; Gasparik, M.; van Wees, J.-D.; Nelskamp, S.

    Sedimentary basins in NW-Germany and the Netherlands represent potential targets for shale gas exploration in Europe due to the presence of Cretaceous (Wealden) and Jurassic (Posidonia) marlstones/shales as well as various Carboniferous black shales. In order to assess the regional shale gas

  2. Dry Volume Fracturing Simulation of Shale Gas Reservoir

    Science.gov (United States)

    Xu, Guixi; Wang, Shuzhong; Luo, Xiangrong; Jing, Zefeng

    2017-11-01

    Application of CO2 dry fracturing technology to shale gas reservoir development in China has advantages of no water consumption, little reservoir damage and promoting CH4 desorption. This paper uses Meyer simulation to study complex fracture network extension and the distribution characteristics of shale gas reservoirs in the CO2 dry volume fracturing process. The simulation results prove the validity of the modified CO2 dry fracturing fluid used in shale volume fracturing and provides a theoretical basis for the following study on interval optimization of the shale reservoir dry volume fracturing.

  3. Developments in production of synthetic fuels out of Estonian shale

    Energy Technology Data Exchange (ETDEWEB)

    Aarna, Indrek

    2010-09-15

    Estonia is still the world leader in utilization of oil shale. Enefit has cooperated with Outotec to develop a new generation of solid heat carrier technology - Enefit280, which is more efficient, environmentally friendlier and has higher unit capacity. Breakeven price of oil produced in Enefit280 process is competitive with conventional oils. The new technology has advantages that allow easy adaptation to other oil shales around the world. Hydrotreated shale oil liquids have similar properties to crude oil cuts. Design for a shale oil hydrotreater unit can use process concepts, hardware components, and catalysts commercially proven in petroleum refining services.

  4. Geothermal alteration of clay minerals and shales: diagenesis

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, C.E.

    1979-07-01

    The objective of this report is to perform a critical review of the data on the mineral and chemical alterations that occur during diagenesis and low-grade metamorphism of shale and other clay-rich rocks - conditions similar to those expected from emplacement of heat-producing radioactive waste in a geologic repository. The conclusions drawn in this document are that the following type of alterations could occur: smectite alteration, ion mobilization, illitic shales, kaolinite reactions, chlorite reactions, organic reactions, paleotemperatures, low temperature shales, high temperature shales, and phase equilibrium changes.

  5. DEMONSTRATION BULLETIN: IN SITU ELECTROKINETIC EXTRACTION SYSTEM - SANDIA NATIONAL LABORATORIES

    Science.gov (United States)

    Sandia National Laboratories (SNL) has developed an in situ soil remediation system that uses electrokinetic principles to remediate hexavalent chromium-contaminated unsaturated or partially saturated soils. The technology involves the in situ application of direct current to the...

  6. Comparison of in situ nutrient degradabilities of alternative by ...

    African Journals Online (AJOL)

    product feed; MBPF) were compared with shelled maize (SM) and soyabean meal (SBM) for their in situ nutrient disappearance. In situ experiments were conducted in two rumen fistulated Holstein cows to evaluate dry matter (DM), crude.

  7. Water Resources Management for Shale Energy Development

    Science.gov (United States)

    Yoxtheimer, D.

    2015-12-01

    The increase in the exploration and extraction of hydrocarbons, especially natural gas, from shale formations has been facilitated by advents in horizontal drilling and hydraulic fracturing technologies. Shale energy resources are very promising as an abundant energy source, though environmental challenges exist with their development, including potential adverse impacts to water quality. The well drilling and construction process itself has the potential to impact groundwater quality, however if proper protocols are followed and well integrity is established then impacts such as methane migration or drilling fluids releases can be minimized. Once a shale well has been drilled and hydraulically fractured, approximately 10-50% of the volume of injected fluids (flowback fluids) may flow out of the well initially with continued generation of fluids (produced fluids) throughout the well's productive life. Produced fluid TDS concentrations often exceed 200,000 mg/L, with elevated levels of strontium (Sr), bromide (Br), sodium (Na), calcium (Ca), barium (Ba), chloride (Cl), radionuclides originating from the shale formation as well as fracturing additives. Storing, managing and properly disposisng of these fluids is critical to ensure water resources are not impacted by unintended releases. The most recent data in Pennsylvania suggests an estimated 85% of the produced fluids were being recycled for hydraulic fracturing operations, while many other states reuse less than 50% of these fluids and rely moreso on underground injection wells for disposal. Over the last few years there has been a shift to reuse more produced fluids during well fracturing operations in shale plays around the U.S., which has a combination of economic, regulatory, environmental, and technological drivers. The reuse of water is cost-competitive with sourcing of fresh water and disposal of flowback, especially when considering the costs of advanced treatment to or disposal well injection and lessens

  8. Acidization of shales with calcite cemented fractures

    Science.gov (United States)

    Kwiatkowski, Kamil; Szymczak, Piotr; Jarosiński, Marek

    2017-04-01

    Investigation of cores drilled from shale formations reveals a relatively large number of calcite-cemented fractures. Usually such fractures are reactivated during fracking and can contribute considerably to the permeability of the resulting fracture network. However, calcite coating on their surfaces effectively excludes them from production. Dissolution of the calcite cement by acidic fluids is investigated numerically with focus on the evolution of fracture morphology. Available surface area, breakthrough time, and reactant penetration length are calculated. Natural fractures in cores from Pomeranian shale formation (northern Poland) were analyzed and classified. Representative fractures are relatively thin (0.1 mm), flat and completely sealed with calcite. Next, the morphology evolution of reactivated natural fractures treated with low-pH fluids has been simulated numerically under various operating conditions. Depth-averaged equations for fracture flow and reactant transport has been solved by finite-difference method coupled with sparse-matrix solver. Transport-limited dissolution has been considered, which corresponds to the treatment with strong acids, such as HCl. Calcite coating in reactivated natural fractures dissolves in a highly non-homogeneous manner - a positive feedback between fluid transport and calcite dissolution leads to the spontaneous formation of wormhole-like patterns, in which most of the flow is focused. The wormholes carry reactive fluids deeper inside the system, which dramatically increases the range of the treatment. Non-uniformity of the dissolution patterns provides a way of retaining the fracture permeability even in the absence of the proppant, since the less dissolved regions will act as supports to keep more dissolved regions open. Evolution of fracture morphology is shown to depend strongly on the thickness of calcite layer - the thicker the coating the more pronounced wormholes are observed. However the interaction between

  9. ISRM Suggested Method for In Situ Microseismic Monitoring of the Fracturing Process in Rock Masses

    Science.gov (United States)

    Xiao, Ya-Xun; Feng, Xia-Ting; Hudson, John A.; Chen, Bing-Rui; Feng, Guang-Liang; Liu, Jian-Po

    2016-01-01

    The purpose of this ISRM Suggested Method is to describe a methodology for in situ microseismic monitoring of the rock mass fracturing processes occurring as a result of excavations for rock slopes, tunnels, or large caverns in the fields of civil, hydraulic, or mining engineering. In this Suggested Method, the equipment that is required for a microseismic monitoring system is described; the procedures are outlined and illustrated, together with the methods for data acquisition and processing for improving the monitoring results. There is an explanation of the methods for presenting and interpreting the results, and recommendations are supported by several examples.

  10. Data mining

    CERN Document Server

    Gorunescu, Florin

    2011-01-01

    The knowledge discovery process is as old as Homo sapiens. Until some time ago, this process was solely based on the 'natural personal' computer provided by Mother Nature. Fortunately, in recent decades the problem has begun to be solved based on the development of the Data mining technology, aided by the huge computational power of the 'artificial' computers. Digging intelligently in different large databases, data mining aims to extract implicit, previously unknown and potentially useful information from data, since 'knowledge is power'. The goal of this book is to provide, in a friendly way

  11. Mining Review

    Science.gov (United States)

    ,

    2013-01-01

    In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals’ contribution to the GDP increased for the second consecutive year.

  12. The stability of fault systems in the south shore of the St. Lawrence Lowlands of Quebec - Implications for shale gas development

    Energy Technology Data Exchange (ETDEWEB)

    Brodylo, John [Questerre Energy Corporation (Canada); Chatellier, Jean-Yves [Talisman Energy Inc (Canada); Matton, Guillaume; Rheault, Michel [Viasat GeoTechnologies (Canada)

    2011-07-01

    Concerns have recently been raised regarding the shale gas industry and its potential impact on shallow aquifers and surface structures, following recent earthquakes in the St. Lawrence Lowlands of Quebec. This paper gathered available geophysical information on the St. Lawrence Lowlands in order to catalogue and map the actual fault network of the deposits which could be involved in future shale gas development with a view to correlating the possible impact of such an industry with the earthquake and stress state. The study gathered a large amount of information on the major tectonic domains and history of earthquakes along Quebec's south shore and also listed in-situ stress in all deposit strata. Tools such as 2-D seismic and aeromagnetic surveys of the area helped in correlating fault location with in-situ stress. Results showed that the Utica shale reservoir, on the south shore of the St. Lawrence, is located in a quiet seismic zone and fracture-induced exploitation of this reservoir is very unlikely to reactivate faults, which are too deep underneath, or to impact on the sub-surface aquifer, given good fracture height containment.

  13. Organoporosity Evaluation of Shale: A Case Study of the Lower Silurian Longmaxi Shale in Southeast Chongqing, China

    Directory of Open Access Journals (Sweden)

    Fangwen Chen

    2014-01-01

    Full Text Available The organopores play an important role in determining total volume of hydrocarbons in shale gas reservoir. The Lower Silurian Longmaxi Shale in southeast Chongqing was selected as a case to confirm the contribution of organopores (microscale and nanoscale pores within organic matters in shale formed by hydrocarbon generation to total volume of hydrocarbons in shale gas reservoir. Using the material balance principle combined with chemical kinetics methods, an evaluation model of organoporosity for shale gas reservoirs was established. The results indicate that there are four important model parameters to consider when evaluating organoporosity in shale: the original organic carbon (w(TOC0, the original hydrogen index (IH0, the transformation ratio of generated hydrocarbon (F(Ro, and the organopore correction coefficient (C. The organoporosity of the Lower Silurian Longmaxi Shale in the Py1 well is from 0.20 to 2.76%, and the average value is 1.25%. The organoporosity variation trends and the residual organic carbon of Longmaxi Shale are consistent in section. The residual organic carbon is indicative of the relative levels of organoporosity, while the samples are in the same shale reservoirs with similar buried depths.

  14. CORE-BASED INTEGRATED SEDIMENTOLOGIC, STRATIGRAPHIC, AND GEOCHEMICAL ANALYSIS OF THE OIL SHALE BEARING GREEN RIVER FORMATION, UINTA BASIN, UTAH

    Energy Technology Data Exchange (ETDEWEB)

    Lauren P. Birgenheier; Michael D. Vanden Berg,

    2011-04-11

    An integrated detailed sedimentologic, stratigraphic, and geochemical study of Utah's Green River Formation has found that Lake Uinta evolved in three phases (1) a freshwater rising lake phase below the Mahogany zone, (2) an anoxic deep lake phase above the base of the Mahogany zone and (3) a hypersaline lake phase within the middle and upper R-8. This long term lake evolution was driven by tectonic basin development and the balance of sediment and water fill with the neighboring basins, as postulated by models developed from the Greater Green River Basin by Carroll and Bohacs (1999). Early Eocene abrupt global-warming events may have had significant control on deposition through the amount of sediment production and deposition rates, such that lean zones below the Mahogany zone record hyperthermal events and rich zones record periods between hyperthermals. This type of climatic control on short-term and long-term lake evolution and deposition has been previously overlooked. This geologic history contains key points relevant to oil shale development and engineering design including: (1) Stratigraphic changes in oil shale quality and composition are systematic and can be related to spatial and temporal changes in the depositional environment and basin dynamics. (2) The inorganic mineral matrix of oil shale units changes significantly from clay mineral/dolomite dominated to calcite above the base of the Mahogany zone. This variation may result in significant differences in pyrolysis products and geomechanical properties relevant to development and should be incorporated into engineering experiments. (3) This study includes a region in the Uinta Basin that would be highly prospective for application of in-situ production techniques. Stratigraphic targets for in-situ recovery techniques should extend above and below the Mahogany zone and include the upper R-6 and lower R-8.

  15. Survey of existing underground openings for in-situ experimental facilities

    Energy Technology Data Exchange (ETDEWEB)

    Wollenberg, H.; Graf, A.; Strisower, B.; Korbin, G.

    1981-07-01

    In an earlier project, a literature search identified 60 underground openings in crystalline rock capable of providing access for an in-situ experimental facility to develop geochemical and hydrological techniques for evaluating sites for radioactive waste isolation. As part of the current project, discussions with state geologists, owners, and operators narrowed the original group to 14. Three additional sites in volcanic rock and one site in granite were also identified. Site visits and application of technical criteria, including the geologic and hydrologic settings and depth, extent of the rock unit, condition, and accessibility of underground workings, determined four primary candidate sites: the Helms Pumped Storage Project in grandiodorite of the Sierra Nevada, California; the Tungsten Queen Mine in Precambrian granodiorite of the North Carolina Piedmont; the Mount Hope Mine in Precambrian granite and gneiss of northern New Jersey; and the Minnamax Project in the Duluth gabbro complex of northern Minnesota.

  16. THE SHALE SOLUTION -How the Economic Growth Shale Gas Production in Pennsylvania has Contributed to can be Maintained, Even After the Gas is Depleted.

    OpenAIRE

    Akselsen, Anniken Berg

    2014-01-01

    The emergence of hydrocarbon energy extracted from shale has been nicknamed the Shale Gas Revolution , due to its implications for the American society, geo-politics and economy. This thesis will explain how the economic growth shale gas production in Pennsylvania so far has contributed to can be maintained, also for the future, when shale gas is no longer produced or depleted. By focusing on Pennsylvania, which has the nation s highest shale gas production growth rate, this thesis will exam...

  17. mining activities.

    African Journals Online (AJOL)

    Eichhornia crassipes) is patchy. L2: Nyikonga, 02°48' 45.0"S,. 007.6"E. (M). Nyikonga area receives discharge from. Nyikonga River that drains Nyarugusu and other mining areas in Geita District. Shoreline vegetation includes Typha capensis ...

  18. Trace elements in oil shale. Progress report, 1979-1980

    Energy Technology Data Exchange (ETDEWEB)

    Chappell, W R

    1980-01-01

    The purpose of this research program is to understand the potential impact of an oil shale industry on environmental levels of trace contaminants in the region. The program involves a comprehensive study of the sources, release mechanisms, transport, fate, and effects of toxic trace chemicals, principally the trace elements, in an oil shale industry. The overall objective of the program is to evaluate the environmental and health consequences of the release of toxic trace elements by shale and oil production and use. The baseline geochemical survey shows that stable trace elements maps can be constructed for numerous elements and that the trends observed are related to geologic and climatic factors. Shale retorted by above-ground processes tends to be very homogeneous (both in space and in time) in trace element content. Leachate studies show that significant amounts of B, F, and Mo are released from retorted shales and while B and Mo are rapidly flushed out, F is not. On the other hand, As, Se, and most other trace elements are not present in significant quantities. Significant amounts of F and B are also found in leachates of raw shales. Very large concentrations of reduced sulfur species are found in leachates of processed shale. Very high levels of B and Mo are taken up in some plants growing on processed shale with and without soil cover. There is a tendency for some trace elements to associate with specific organic fractions, indicating that organic chelation or complexation may play an important role. Many of the so-called standard methods for analyzing trace elements in oil shale-related materials are inadequate. A sampling manual is being written for the environmental scientist and practicing engineer. A new combination of methods is developed for separating the minerals in oil shale into different density fractions. Microbial investigations have tentatively identified the existence of thiobacilli in oil shale materials such as leachates. (DC)

  19. Effects of aqueous effluents from in situ fossil fuel processing technologies on aquatic systems. Annual progress report, January 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, H.L.

    1980-01-04

    This is the third annual progress report for a continuing EPA-DOE jointly funded project to evaluate the effects of aqueous effluents from in situ fossil-fuel processing technologies on aquatic biota. The project is organized into four project tasks: (1) literature review; (2) process water screening; (3) methods development; and (4) recommendations. Our Bibliography of aquatic ecosystem effects, analytical methods and treatment technologies for organic compounds in advanced fossil-fuel processing effluents was submitted to the EPA for publication. The bibliography contains 1314 citations indexed by chemicals, keywords, taxa and authors. We estimate that the second bibliography volume will contain approximately 1500 citations and be completed in February. We compiled results from several laboratories of inorganic characterizations of 19 process waters: 55 simulated in situ oil-shale retort waters; and Hanna-3, Hanna-4B 01W and Lawrence Livermore Hoe Creek underground coal gasification condenser waters. These process waters were then compared to a published summary of the analyses from 18 simulated in situ oil-shale retort waters. We completed this year 96-h flow-through toxicity bioassays with fathead minnows and rainbow trout and 48-h flow-through bioassays with Daphnia pulicaria exposed to 5 oil-shale process waters, 1 tar-sand process water, 2 underground coal gasification condenser waters, 1 post-gasification backflood condenser water, as well as 2 bioassays with fossil-fuel process water constituents. The LC/sub 50/ toxicity values for these respective species when exposed to these waters are given in detail. (LTN)

  20. Investigation of the geokinetics horizontal in situ oil shale retorting process. Quarterly report, October, November, December 1983

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, K.B.

    1984-03-01

    Retort No. 27 was ignited on August 11, 1983 and by December 31 had completed 139 days of operation and produced 11,420 barrels of oil. Retort No. 28 was ignited on October 18, 1983 and on December 31 had completed 74 days of operation and produced 5,285 barrels of oil. The off-gas processing plants for the two retorts was completed and put through a shakedown run. Concentration levels of H/sub 2/S and NH/sub 3/ in the retort off gas did not warrant plant operation in the fourth quarter. Environmental studies are reported.

  1. The treatment of in situ breast cancer

    Energy Technology Data Exchange (ETDEWEB)

    Fentiman, I.S. (Guy' s Hospital, London (UK). Clinical Oncology Unit)

    1989-01-01

    Carcinoma in situ is the earliest histologically recognisable form of malignancy and as such provides an opportunity to treat the disease in a curative way. The two major variants, ductal carcinoma in situ (DCIS) and lobular carcinoma in situ (LCIS) will be considered separately as the two conditions have divergent natural histories. DCIS is increasing in incidence since microcalcification may be detected radiologically in the screening of asymptomatic women. The extent of microcalcification may not indicate the extent of disease. It has yet to be determined whether there is a difference in behaviour of the tumour forming and the asymptomatic types of DCIS. After a biopsy has shown DCIS there will be residual DCIS at the biopsy site in one-third of patients, and multifocal DCIS in another third. A coexistent infiltrating carcinoma may be present in up to 16%. Due to sampling problems areas of invasion may be missed. Axillary nodal metastases are found in only 1% of patients with histological DCIS. Radical surgery by total or modified mastectomy is almost curative, but 3% of patients will die of metastases. Taking results of uncontrolled trials, local relapse rates are as follows: excision alone 50%, wide excision 30%, wide excision plus radiotherapy 20%. Two prospective trials are underway run by the EORTC and NSABP in which patients with DCIS are treated by wide excision with or without external radiotherapy. LCIS is usually an incidental finding with a bilateral predisposition to subsequent infiltrating carcinomas. Curative procedures such as bilateral mastectomy with reconstruction may represent overtreatment. A systemic rather than local approach would seem appropriate and a trial is now underway run by the EORTC in which patients with histologically confirmed LCIS are randomised to observation alone or to receive tamoxifen 20 mg daily for 5 years. (orig./MG).

  2. Nanoindentation in situ a Transmission Electron Microscope

    OpenAIRE

    Johnson, Lars

    2007-01-01

    The technique of Nanoindentation in situ Transmission Electron Microscope has been implemented on a Philips CM20. Indentations have been performed on Si and Sapphire (α-Al2O3) cut from wafers; Cr/Sc multilayers and Ti3SiC2 thin films. Different sample geometries and preparation methods have been evaluated. Both conventional ion and Focused Ion Beam milling were used, with different ways of protecting the sample during milling. Observations were made of bending and fracture of samples, disloca...

  3. In situ fabrication of a tunable microlens.

    Science.gov (United States)

    Zhang, Lei; Wang, Zhiyuan; Wang, Yichuan; Qiu, Rui; Fang, Wei; Tong, Limin

    2015-08-15

    We demonstrate an optofluidic variable-focus microlens formed by a solid polydimethylsiloxane (PDMS) meniscus channel wall and a tunable liquid lens body. A novel method for in situ fabrication of the meniscus channel wall is developed by introducing liquid PDMS prepolymer into a microchannel followed by curing. Three-light manipulation techniques including tunable optical focusing, collimating, and diverging are realized by varying the refractive index (RI) of liquid lens body. Also, we present an absorption measurement of methylene blue (MB) with a collimated probing light, achieving a detection limit of 0.25 μM by using a 5-mm-long detection cell.

  4. In situ viscometry by optical trapping interferometry

    DEFF Research Database (Denmark)

    Guzmán, C.; Flyvbjerg, Henrik; Köszali, R.

    2008-01-01

    We demonstrate quantitative in situ viscosity measurements by tracking the thermal fluctuations of an optically trapped microsphere subjected to a small oscillatory flow. The measured power spectral density of the sphere's positions displays a characteristic peak at the driving frequency...... of the flow, which is simply proportional to the viscosity, when measured in units of the thermal power spectral density at the same frequency. Measurements are validated on different water-glycerol mixtures, as well as in a glycerol gradient, where no a priori knowledge of the solution is used to determine...

  5. Unannounced in situ simulation of obstetric emergencies

    DEFF Research Database (Denmark)

    Sorensen, Jette Led; Lottrup, Pernille; van der Vleuten, Cees

    2014-01-01

    AIM: To describe how unannounced in situ simulation (ISS) was perceived by healthcare professionals before and after its implementation, and to describe the organisational impact of ISS. STUDY DESIGN: Ten unannounced ISS involving all staff were scheduled March-August 2007. Questionnaire surveys...... on staff perceptions were conducted before (2003-2006) and after (2007-2008) implementation of unannounced ISS. Information from the debriefing sessions following each ISS constituted a proxy measure of the organisational impact of the ISS. RESULTS: Five out of ten of the unannounced ISS scheduled were...

  6. In Situ Preservation of Historic Spacecraft

    Science.gov (United States)

    Barclay, R.; Brooks, R.

    The loss of the Mir space station is shown to symbolize a new consciousness of the value of space artefacts. The reasons why such artefacts as Mir become historic objects worthy of preservation are examined. Preservation of space vehicles in situ is discussed, with particular reference to safety, monitoring and long term costs. An argument is made for a wider definition for World Heritage designations to include material beyond the surface of the Earth, and for international bodies to assess, monitor and oversee these projects. Such heritage sites are seen as an economic driver for the development of space tourism in the 21st century.

  7. Polypropylene/graphite nanocomposites by in situ polymerization; Nanocompositos polipropileno/grafite via polimerizacao in situ

    Energy Technology Data Exchange (ETDEWEB)

    Milani, Marceo A.; Galland, Giselda B., E-mail: griselda@iq.ufrgs.br [Instituto de Quimica, UFRGS, Porto Alegre, RS (Brazil); Quijada, Raul [Universidade de Chile, Santiago (Chile). Centro de Ciencias de los Materiales; Basso, Nara R.S. [Fac. de Quimica, PUCRS, Porto Alegre, RS (Brazil)

    2011-07-01

    This work presents the synthesis of nanocomposites of polypropylene/graphite by in situ polymerization using metallocene catalyst and graphene nanosheets. Initially was analyzed which of the metallocene catalysts rac-Et(Ind){sub 2}ZrCl{sub 2} or rac-Me{sub 2}Si(Ind){sub 2}ZrCl{sub 2} produces polypropylene with mechanical properties more relevant. Then it were performed the in situ polymerization reactions to obtain the nanocomposites. The polymeric materials were characterized by XRD, DSC, GPC and DMTA. (author)

  8. Windfall Wealth and Shale Development in Appalachian Ohio: Preliminary Results

    Science.gov (United States)

    Bates, James S.; Loy, Polly Wurster

    2016-01-01

    The response by agriculture/natural resources and community development Extension educators to shale development in Ohio has been proactive. There is a need, however, to understand the impact that shale development is having broadly on families and communities and specifically as it relates to lease payments and the perceptions and realities of…

  9. Palaeoclimatic Control on the Composition of Palaeozoic Shales ...

    African Journals Online (AJOL)

    The abundant plagioclase in the lowest two formations could, therefore, be due to less pervasive chemical weathering rather than erosion of a distinct source. In this paper, geochemical data for fine-grained sedimentary rocks of the Ajua Shale and the Takoradi Shale (that overlie the Elmina Sandstone) formations are used ...

  10. Multivariate analysis relating oil shale geochemical properties to NMR relaxometry

    Science.gov (United States)

    Birdwell, Justin E.; Washburn, Kathryn E.

    2015-01-01

    Low-field nuclear magnetic resonance (NMR) relaxometry has been used to provide insight into shale composition by separating relaxation responses from the various hydrogen-bearing phases present in shales in a noninvasive way. Previous low-field NMR work using solid-echo methods provided qualitative information on organic constituents associated with raw and pyrolyzed oil shale samples, but uncertainty in the interpretation of longitudinal-transverse (T1–T2) relaxometry correlation results indicated further study was required. Qualitative confirmation of peaks attributed to kerogen in oil shale was achieved by comparing T1–T2 correlation measurements made on oil shale samples to measurements made on kerogen isolated from those shales. Quantitative relationships between T1–T2 correlation data and organic geochemical properties of raw and pyrolyzed oil shales were determined using partial least-squares regression (PLSR). Relaxometry results were also compared to infrared spectra, and the results not only provided further confidence in the organic matter peak interpretations but also confirmed attribution of T1–T2 peaks to clay hydroxyls. In addition, PLSR analysis was applied to correlate relaxometry data to trace element concentrations with good success. The results of this work show that NMR relaxometry measurements using the solid-echo approach produce T1–T2 peak distributions that correlate well with geochemical properties of raw and pyrolyzed oil shales.

  11. The Geopolitical Impact of Shale Gas : The Modelling Approach

    NARCIS (Netherlands)

    Auping, W.L.; De Jong, S.; Pruyt, E.; Kwakkel, J.H.

    2014-01-01

    The US’ shale gas revolution, a spectacular increase in natural gas extraction from previously unconventional sources, has led to considerable lower gas prices in North America. This study focusses on consequences of the shale gas revolution on state stability of traditional oil and gas exporting

  12. Updated methodology for nuclear magnetic resonance characterization of shales

    Science.gov (United States)

    Washburn, Kathryn E.; Birdwell, Justin E.

    2013-08-01

    Unconventional petroleum resources, particularly in shales, are expected to play an increasingly important role in the world's energy portfolio in the coming years. Nuclear magnetic resonance (NMR), particularly at low-field, provides important information in the evaluation of shale resources. Most of the low-field NMR analyses performed on shale samples rely heavily on standard T1 and T2 measurements. We present a new approach using solid echoes in the measurement of T1 and T1-T2 correlations that addresses some of the challenges encountered when making NMR measurements on shale samples compared to conventional reservoir rocks. Combining these techniques with standard T1 and T2 measurements provides a more complete assessment of the hydrogen-bearing constituents (e.g., bitumen, kerogen, clay-bound water) in shale samples. These methods are applied to immature and pyrolyzed oil shale samples to examine the solid and highly viscous organic phases present during the petroleum generation process. The solid echo measurements produce additional signal in the oil shale samples compared to the standard methodologies, indicating the presence of components undergoing homonuclear dipolar coupling. The results presented here include the first low-field NMR measurements performed on kerogen as well as detailed NMR analysis of highly viscous thermally generated bitumen present in pyrolyzed oil shale.

  13. Weathering characteristics of the Lower Paleozoic black shale in ...

    Indian Academy of Sciences (India)

    The northwestern Guizhou in the Yangtze Craton of south China has a tremendous potential of shale gas resource. In this paper, we present results from major and trace elements, total organic carbon, mineralogical composition analysis and petrophysical parameters to characterise shale weathering features. Further, the ...

  14. Shale Gas in Europe: pragmatic perspectives and actions

    Directory of Open Access Journals (Sweden)

    Horsfield B.

    2012-10-01

    Full Text Available Natural gas will continue to play a key role in the EU’s energy mix in the coming years, with unconventional gas’ role increasing in importance as new resources are exploited worldwide. As far as Europe’s own shale gas resources are concerned, it is especially the public’s perception and level of acceptance that will make or break shale gas in the near-term. Both the pros and cons need to be discussed based on factual argument rather than speculation. Research organizations such as ours (GFZ German Research Centre for Geosciences have an active and defining role to play in remedying this deficiency. As far as science and technology developments are concerned, the project “Gas Shales in Europe” (GASH and the shale gas activities of “GeoEnergie” (GeoEn are the first major initiatives in Europe focused on shale gas. Basic and applied geoscientific research is conducted to understand the fundamental nature and interdependencies of the processes leading to shale gas formation. When it comes to knowledge transfer, the perceived and real risks associated with shale gas exploitation need immediate evaluation in Europe using scientific analysis. To proactively target these issues, the GFZ and partners are launching the European sustainable Operating Practices (E-SOP Initiative for Unconventional Resources. The web-based Shale Gas Information Platform (SHIP brings these issues into the public domain.

  15. Market analysis of shale oil co-products. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    Data are presented in these appendices on the marketing and economic potential for soda ash, aluminia, and nahcolite as by-products of shale oil production. Appendices 1 and 2 contain data on the estimated capital and operating cost of an oil shales/mineral co-products recovery facility. Appendix 3 contains the marketing research data.

  16. Implementation of an anisotropic mechanical model for shale in Geodyn

    Energy Technology Data Exchange (ETDEWEB)

    Attia, A; Vorobiev, O; Walsh, S

    2015-05-15

    The purpose of this report is to present the implementation of a shale model in the Geodyn code, based on published rock material models and properties that can help a petroleum engineer in his design of various strategies for oil/gas recovery from shale rock formation.

  17. Shales: A review of their classifications, properties and importance ...

    African Journals Online (AJOL)

    Generally, shales have moderate to high clay content (average, 57%), low strength (range, 5-30MPa), low permeability(range, 1 x 10-6 - 10-12 m/s) and are water sensitive(susceptible to hydration and swelling when in contact with water). Shales are important to the petroleum industry because of their usefulness as source ...

  18. Shale gas wastewater management under uncertainty.

    Science.gov (United States)

    Zhang, Xiaodong; Sun, Alexander Y; Duncan, Ian J

    2016-01-01

    This work presents an optimization framework for evaluating different wastewater treatment/disposal options for water management during hydraulic fracturing (HF) operations. This framework takes into account both cost-effectiveness and system uncertainty. HF has enabled rapid development of shale gas resources. However, wastewater management has been one of the most contentious and widely publicized issues in shale gas production. The flowback and produced water (known as FP water) generated by HF may pose a serious risk to the surrounding environment and public health because this wastewater usually contains many toxic chemicals and high levels of total dissolved solids (TDS). Various treatment/disposal options are available for FP water management, such as underground injection, hazardous wastewater treatment plants, and/or reuse. In order to cost-effectively plan FP water management practices, including allocating FP water to different options and planning treatment facility capacity expansion, an optimization model named UO-FPW is developed in this study. The UO-FPW model can handle the uncertain information expressed in the form of fuzzy membership functions and probability density functions in the modeling parameters. The UO-FPW model is applied to a representative hypothetical case study to demonstrate its applicability in practice. The modeling results reflect the tradeoffs between economic objective (i.e., minimizing total-system cost) and system reliability (i.e., risk of violating fuzzy and/or random constraints, and meeting FP water treatment/disposal requirements). Using the developed optimization model, decision makers can make and adjust appropriate FP water management strategies through refining the values of feasibility degrees for fuzzy constraints and the probability levels for random constraints if the solutions are not satisfactory. The optimization model can be easily integrated into decision support systems for shale oil/gas lifecycle

  19. Spatio-temporal microseismic analysis of the Woodford Shale, Canadian County, Oklahoma

    Science.gov (United States)

    Eppehimer, Jarred

    Microseismicity provides data that can be used to monitor hydraulic fracture stimulation programs as well as to characterize the resulting hydraulic fractures. This is especially important in low permeability gas and oil shales, where the creation of additional permeability through these fracture treatments is essential to production. However, many applications and analyses of these data are either qualitative in nature or include a large element of interpretational bias. This study looks at two microseismic analytical techniques: the radius of gyration (ROG) tensor, as described in Sayers & Le Calvez (2010), and the methods described in Shapiro (2008) that relate spatio-temporal microseismic signatures to hydraulic diffusivity and ultimately hydraulic permeability. The radius of gyration tensor is used to generate a characteristic ellipsoid for any set of microseismic events, and the aspect ratio of this ellipsoid can be related to local in-situ horizontal stress ratios. These methods are applied to surface microseismic data collected for six horizontal wells drilled and completed in the Woodford Shale in Canadian County, Oklahoma. Additionally, an attempt is made to bridge the gap between these methods. Specifically, the characteristic ellipsoid generation from the radius of gyration tensor in Sayers & Le Calvez (2010) is applied to Shapiro's workflow. Shapiro attempts to link the 3D anisotropic triggering front of seismicity, which is an ellipsoid that envelops time-scaled microseismic events, to reservoir permeability. The radius of gyration tensor will generate this ellipsoid and remove interpretational bias that would have been present otherwise. Lastly, an attempt is made at relating the signatures present in the characteristic ellipsoids to zones of natural fracture reactivation. This is done on a stage-by-stage basis. The hypothesis is that an ellipsoid with a significant tilt in its most vertical principal axis and a significant azimuthal rotation away

  20. The Spatial and Temporal Consumptive Water Use Impacts of Rapid Shale Gas Development and Use in Texas

    Science.gov (United States)

    Pacsi, A. P.; Allen, D.

    2013-12-01

    ) mining and natural gas production in Texas were also estimated, and water consumption was aggregated by river basin for spatial resolution. Temporal results indicated that the development of shale gas resources during the episode led to a net reduction in consumptive water use in Texas but that a lag time existed before the water use in natural gas production regions was offset by changes in the electricity generation and lignite mining sectors. The water impact on specific river basins in production regions was varied. Some river basins had sufficient changes in coal-fired power plant generation to offset increased water use in shale gas production and for cooling at natural-gas fired power plants, while others did not. Thus, some areas have likely experienced increased water use due to shale gas production despite overall reductions in life-cycle consumptive water use in the state. The largest consumptive water use increase for a river basin, however, was less than 1% of its total water consumption.

  1. Contract Mining versus Owner Mining

    African Journals Online (AJOL)

    Owner

    products affecting mining performance, usage rate above plan, etc.), people (e.g. skill deficiencies of key personnel, poor safety and environmental awareness), cost estimation (using incorrect unit costs in calculations, escalation of costs higher than revenue increases, changes in interest rates, change in exchange rates), ...

  2. Sulfide Generation by DominantHalanaerobiumMicroorganisms in Hydraulically Fractured Shales.

    Science.gov (United States)

    Booker, Anne E; Borton, Mikayla A; Daly, Rebecca A; Welch, Susan A; Nicora, Carrie D; Hoyt, David W; Wilson, Travis; Purvine, Samuel O; Wolfe, Richard A; Sharma, Shikha; Mouser, Paula J; Cole, David R; Lipton, Mary S; Wrighton, Kelly C; Wilkins, Michael J

    2017-01-01

    Hydraulic fracturing of black shale formations has greatly increased United States oil and natural gas recovery. However, the accumulation of biomass in subsurface reservoirs and pipelines is detrimental because of possible well souring, microbially induced corrosion, and pore clogging. Temporal sampling of produced fluids from a well in the Utica Shale revealed the dominance of Halanaerobium strains within the in situ microbial community and the potential for these microorganisms to catalyze thiosulfate-dependent sulfidogenesis. From these field data, we investigated biogenic sulfide production catalyzed by a Halanaerobium strain isolated from the produced fluids using proteogenomics and laboratory growth experiments. Analysis of Halanaerobium isolate genomes and reconstructed genomes from metagenomic data sets revealed the conserved presence of rhodanese-like proteins and anaerobic sulfite reductase complexes capable of converting thiosulfate to sulfide. Shotgun proteomics measurements using a Halanaerobium isolate verified that these proteins were more abundant when thiosulfate was present in the growth medium, and culture-based assays identified thiosulfate-dependent sulfide production by the same isolate. Increased production of sulfide and organic acids during the stationary growth phase suggests that fermentative Halanaerobium uses thiosulfate to remove excess reductant. These findings emphasize the potential detrimental effects that could arise from thiosulfate-reducing microorganisms in hydraulically fractured shales, which are undetected by current industry-wide corrosion diagnostics. IMPORTANCE Although thousands of wells in deep shale formations across the United States have been hydraulically fractured for oil and gas recovery, the impact of microbial metabolism within these environments is poorly understood. Our research demonstrates that dominant microbial populations in these subsurface ecosystems contain the conserved capacity for the reduction of

  3. Sulfide Generation by Dominant Halanaerobium Microorganisms in Hydraulically Fractured Shales

    Energy Technology Data Exchange (ETDEWEB)

    Booker, Anne E.; Borton, Mikayla A.; Daly, Rebecca A.; Welch, Susan A.; Nicora, Carrie D.; Hoyt, David W.; Wilson, Travis; Purvine, Samuel O.; Wolfe, Richard A.; Sharma, Shikha; Mouser, Paula J.; Cole, David R.; Lipton, Mary S.; Wrighton, Kelly C.; Wilkins, Michael J.; McMahon, Katherine

    2017-07-05

    ABSTRACT

    Hydraulic fracturing of black shale formations has greatly increased United States oil and natural gas recovery. However, the accumulation of biomass in subsurface reservoirs and pipelines is detrimental because of possible well souring, microbially induced corrosion, and pore clogging. Temporal sampling of produced fluids from a well in the Utica Shale revealed the dominance ofHalanaerobiumstrains within thein situmicrobial community and the potential for these microorganisms to catalyze thiosulfate-dependent sulfidogenesis. From these field data, we investigated biogenic sulfide production catalyzed by aHalanaerobiumstrain isolated from the produced fluids using proteogenomics and laboratory growth experiments. Analysis ofHalanaerobiumisolate genomes and reconstructed genomes from metagenomic data sets revealed the conserved presence of rhodanese-like proteins and anaerobic sulfite reductase complexes capable of converting thiosulfate to sulfide. Shotgun proteomics measurements using aHalanaerobiumisolate verified that these proteins were more abundant when thiosulfate was present in the growth medium, and culture-based assays identified thiosulfate-dependent sulfide production by the same isolate. Increased production of sulfide and organic acids during the stationary growth phase suggests that fermentativeHalanaerobiumuses thiosulfate to remove excess reductant. These findings emphasize the potential detrimental effects that could arise from thiosulfate-reducing microorganisms in hydraulically fractured shales, which are undetected by current industry-wide corrosion diagnostics.

    IMPORTANCEAlthough thousands of wells in deep shale formations across the United States have been hydraulically fractured for oil and gas recovery, the impact of microbial metabolism within these environments is poorly understood. Our

  4. Epistemic values in the Burgess Shale debate

    DEFF Research Database (Denmark)

    Baron, Christian

    2009-01-01

    Focusing primarily on papers and books discussing the evolutionary and systematic interpretation of the Cambrian animal fossils from the Burgess Shale fauna, this paper explores the role of epistemic values in the context of a discipline (paleontology) striving to establish scientific authority...... in defending the privileged historical perspective of paleontology have been disparate and, to an extent contradictory, each impinges on the acceptance of a specific epistemic ideal or set of values and success or failure of each depends on the compatibility of this ideal with the surrounding community...

  5. Catalytic gasification of oil-shales

    Energy Technology Data Exchange (ETDEWEB)

    Lapidus, A.; Avakyan, T. [I.M. Gubkin Russian State Univ. of Oil and Gas, Moscow (Russian Federation); Strizhakova, Yu. [Samara State Univ. (Russian Federation)

    2012-07-01

    Nowadays, the problem of complex usage of solid fossil fuels as raw materials for obtaining of motor fuels and chemical products is becoming increasingly important. A one of possible solutions of the problem is their gasification with further processing of gaseous and liquid products. In this work we have investigated the process of thermal and catalytic gasification of Baltic and Kashpir oil-shales. We have shown that, as compared with non-catalytic process, using of nickel catalyst in the reaction increases the yield of gas, as well as hydrogen content in it, and decreases the amount of liquid products. (orig.)

  6. Mining and beneficiation: A review of possible lunar applications

    Science.gov (United States)

    Chamberlain, Peter G.

    1991-01-01

    Successful exploration of Mars and outer space may require base stations strategically located on the Moon. Such bases must develop a certain self-sufficiency, particularly in the critical life support materials, fuel components, and construction materials. Technology is reviewed for the first steps in lunar resource recovery-mining and beneficiation. The topic is covered in three main categories: site selection; mining; and beneficiation. It will also include (in less detail) in-situ processes. The text described mining technology ranging from simple diggings and hauling vehicles (the strawman) to more specialized technology including underground excavation methods. The section of beneficiation emphasizes dry separation techniques and methods of sorting the ore by particle size. In-situ processes, chemical and thermal, are identified to stimulate further thinking by future researchers.

  7. Clay squirt: Local flow dispersion in shale-bearing sandstones

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2017-01-01

    Dispersion of elastic-wave velocity is common in sandstone and larger in shaly sandstone than in clean sandstone. Dispersion in fluid-saturated shaly sandstone often exceeds the level expected from the stress-dependent elastic moduli of dry sandstone. The large dispersion has been coined clay...... squirt and is proposed to originate from a pressure gradient between the clay microporosity and the effective porosity. We have formulated a simple model that quantifies the clay-squirt effect on bulk moduli of sandstone with homogeneously distributed shale laminae or dispersed shale. The model...... predictions were compared with the literature data. For sandstones with dispersed shale, agreement was found, whereas other sandstones have larger fluid-saturated bulk modulus, possibly due to partially load-bearing shales or heterogeneous shale distribution. The data that agree with the clay-squirt model...

  8. Assessment of industry needs for oil shale research and development

    Energy Technology Data Exchange (ETDEWEB)

    Hackworth, J.H.

    1987-05-01

    Thirty-one industry people were contacted to provide input on oil shale in three subject areas. The first area of discussion dealt with industry's view of the shape of the future oil shale industry; the technology, the costs, the participants, the resources used, etc. It assessed the types and scale of the technologies that will form the industry, and how the US resource will be used. The second subject examined oil shale R D needs and priorities and potential new areas of research. The third area of discussion sought industry comments on what they felt should be the role of the DOE (and in a larger sense the US government) in fostering activities that will lead to a future commercial US oil shale shale industry.

  9. Germ cell neoplasia in situ (GCNIS)

    DEFF Research Database (Denmark)

    Berney, Daniel M; Looijenga, Leendert H J; Idrees, Muhammad

    2016-01-01

    The pre-invasive lesion associated with post-pubertal malignant germ cell tumours of the testis was first recognized in the early 1970s and confirmed by a number of observational and follow-up studies. Until this year, this scientific story has been confused by resistance to the entity and disagr......The pre-invasive lesion associated with post-pubertal malignant germ cell tumours of the testis was first recognized in the early 1970s and confirmed by a number of observational and follow-up studies. Until this year, this scientific story has been confused by resistance to the entity...... and disagreement on its name. Initially termed 'carcinoma in situ' (CIS), it has also been known as 'intratubular germ cell neoplasia, unclassified' (IGCNU) and 'testicular intraepithelial neoplasia' (TIN). In this paper, we review the history of discovery and controversy concerning these names and introduce...... the reasoning for uniting behind a new name, endorsed unanimously at the World Health Organization (WHO) consensus classification 2016: germ cell neoplasia in situ (GCNIS)....

  10. Molecular cytogenetics using fluorescence in situ hybridization

    Energy Technology Data Exchange (ETDEWEB)

    Gray, J.W.; Kuo, Wen-Lin; Lucas, J.; Pinkel, D.; Weier, H-U.; Yu, Loh-Chung.

    1990-12-07

    Fluorescence in situ hybridization (FISH) with chromosome-specific probes enables several new areas of cytogenetic investigation by allowing visual determination of the presence and normality of specific genetic sequences in single metaphase or interphase cells. in this approach, termed molecular cytogenetics, the genetic loci to be analyzed are made microscopically visible in single cells using in situ hybridization with nucleic acid probes specific to these loci. To accomplish this, the DNA in the target cells is made single stranded by thermal denaturation and incubated with single-stranded, chemically modified probe under conditions where the probe will anneal only with DNA sequences to which it has high DNA sequence homology. The bound probe is then made visible by treatment with a fluorescent reagent such as fluorescein that binds to the chemical modification carried by the probe. The DNA to which the probe does not bind is made visible by staining with a dye such as propidium iodide that fluoresces at a wavelength different from that of the reagent used for probe visualization. We show in this report that probes are now available that make this technique useful for biological dosimetry, prenatal diagnosis and cancer biology. 31 refs., 3 figs.

  11. Biophotonic in situ sensor for plant leaves

    Energy Technology Data Exchange (ETDEWEB)

    Conejo, Elian; Frangi, Jean-Pierre; Rosny, Gilles de

    2010-04-01

    Knowledge of the water concentration of plants can be helpful in several environmental and agricultural domains. There are many methods for the determination of water content in plant leaves; however, most of them give a relative moisture level or an analytical measure after a previous calibration procedure. Even for other biochemical compounds such as dry matter or chlorophyll, the measurement techniques could be destructive. For this reason, a nondestructive method has been developed to measure the biochemical compounds of a plant leaf, using an infrared spectroscopy technique. One important advantage is the simplicity of the device (RAdiometre portatif de Mesure In Situ, RAMIS) and its capability to perform measurements in situ. The prototype is a leaf-clip configuration and is made of LEDs at five wavelengths (656, 721, 843, 937, and 1550 nm), and a silicon/germanium photosensor. To compute the water content of vegetative leaves, the radiative transfer model PROSPECT was implemented. This model can accurately predict spectral transmittances in the 400 nm to 2500 nm spectral region as a function of the principal leaf biochemical contents: water, dry matter, and chlorophyll. Using the transmittance measured by RAMIS into an inversion procedure of PROSPECT: A Model of Leaf Optical Properties Spectra, we are able to compute the values of water contents that show an agreement with the water contents measured directly using dry weight procedures. This method is presented as a possibility to estimate other leaf biochemical compounds using appropriate wavelengths.

  12. Enzyme Engineering for In Situ Immobilization.

    Science.gov (United States)

    Rehm, Fabian B H; Chen, Shuxiong; Rehm, Bernd H A

    2016-10-14

    Enzymes are used as biocatalysts in a vast range of industrial applications. Immobilization of enzymes to solid supports or their self-assembly into insoluble particles enhances their applicability by strongly improving properties such as stability in changing environments, re-usability and applicability in continuous biocatalytic processes. The possibility of co-immobilizing various functionally related enzymes involved in multistep synthesis, conversion or degradation reactions enables the design of multifunctional biocatalyst with enhanced performance compared to their soluble counterparts. This review provides a brief overview of up-to-date in vitro immobilization strategies while focusing on recent advances in enzyme engineering towards in situ self-assembly into insoluble particles. In situ self-assembly approaches include the bioengineering of bacteria to abundantly form enzymatically active inclusion bodies such as enzyme inclusions or enzyme-coated polyhydroxyalkanoate granules. These one-step production strategies for immobilized enzymes avoid prefabrication of the carrier as well as chemical cross-linking or attachment to a support material while the controlled oriented display strongly enhances the fraction of accessible catalytic sites and hence functional enzymes.

  13. Geomechaical Behavior of Shale Rocks Under High Pressure and Temperature

    Science.gov (United States)

    Villamor Lora, R.; Ghazanfari, E.

    2014-12-01

    The mechanical properties of shale are demanding parameters for a number of engineering and geomechanical purposes. Borehole stability modeling, geophysics, shale oil and shale gas reservoirs, and underground storage of CO2 in shale formations are some of these potential applications to name a few. The growing interest in these reservoirs, as a source for hydrocarbons production, has resulted in an increasing demand for fundamental rock property data. These rocks are known to be non-linear materials. There are many factors, including induced cracks and their orientation, partial saturation, material heterogeneity and anisotropy, plasticity, strain rate, and temperature that may have an impact on the geomechanical behaviour of these shales.Experimental results and theoretical considerations have shown that the elastic moduli are not single-value, well-defined parameters for a given rock. Finding suitable values for these parameters is of vital importance in many geomechanical applications. In this study, shale heterogeneity and its geomechanical properties are explored through an extensive laboratory experimental program. A series of hydrostatic and triaxial tests were performed in order to evaluate the elasticity, viscoplasticity, yielding and failure response of Marcellus shale samples as a function of pressure and temperature. Additional characterization includes mineralogy, porosity, and permeability measurements. The shale samples were taken from a Marcellus outcrop at State Game Lands 252, located in Lycoming and Union counties, Allenwood, Pennsylvania. Laboratory experiments have shown that creep behaviour is highly sensitive to temperature. Furthermore, the non-linear nature of these rocks reveals interesting behaviour of the elastic moduli highly dependent on stress history of the rock. Results from cyclic triaxial tests point out the different behaviour between 1st-loading and unloading-reloading cycles. Experimental results of these Marcellus shales are

  14. Exploration drilling for pre-mining gas drainage in coal mines

    Science.gov (United States)

    Shubina, E. A.; Brylin, V. I.; Lukyanov, V. G.; Korotchenko, T. V.

    2015-02-01

    High natural gas content in coal seams and low gas drainage efficiency are the basic issues to be addressed in order to ensure coal mining safety. A great number of wells being drilled within various gas drainage techniques significantly increase the costs of coal mining and do not reduce the gas content levels within the coal beds up to the required parameters in a short period of time. The integrated approach toward exploration well spacing applied at the stage of project development could make it possible to consider coal seam data to provide more effective gas drainage not only ahead of mining but also during further gas content reduction and commercial production of methane. The comparative analysis of a closely spaced grid of exploration program compiled in accordance with the recommendations on applying mineral reserves classification and inferred resources of coal and shale coal deposits and currently effective stimulation radius proves the necessity and possibility to consider exploration well data for gas drainage. Pre-mining gas drainage could ensure the safety of mining operations.

  15. Geotechnical characterization of mined clay from Appalachian Ohio: challenges and implications for the clay mining industry.

    Science.gov (United States)

    Moran, Anthony R; Hettiarachchi, Hiroshan

    2011-07-01

    Clayey soil found in coal mines in Appalachian Ohio is often sold to landfills for constructing Recompacted Soil Liners (RSL) in landfills. Since clayey soils possess low hydraulic conductivity, the suitability of mined clay for RSL in Ohio is first assessed by determining its clay content. When soil samples are tested in a laboratory, the same engineering properties are typically expected for the soils originated from the same source, provided that the testing techniques applied are standard, but mined clay from Appalachian Ohio has shown drastic differences in particle size distribution depending on the sampling and/or laboratory processing methods. Sometimes more than a 10 percent decrease in the clay content is observed in the samples collected at the stockpiles, compared to those collected through reverse circulation drilling. This discrepancy poses a challenge to geotechnical engineers who work on the prequalification process of RSL material as it can result in misleading estimates of the hydraulic conductivity of the samples. This paper describes a laboratory investigation conducted on mined clay from Appalachian Ohio to determine how and why the standard sampling and/or processing methods can affect the grain-size distributions. The variation in the clay content was determined to be due to heavy concentrations of shale fragments in the clayey soils. It was also concluded that, in order to obtain reliable grain size distributions from the samples collected at a stockpile of mined clay, the material needs to be processed using a soil grinder. Otherwise, the samples should be collected through drilling.

  16. Mining revival

    OpenAIRE

    Lusty, Paul

    2010-01-01

    In relation to its size the United Kingdom (UK) is remarkably well-endowed with mineral resources as a result of its complex geological history. Their extraction and use have played an important role in the development of the UK economy over many years and minerals are currently worked at some 2100 mine and quarry sites. Production is now largely confined to construction minerals, primarily aggregates, energy minerals and industrial minerals including salt, potash, kaolin and fluorspar, altho...

  17. Full field reservoir modeling of shale assets using advanced data-driven analytics

    Directory of Open Access Journals (Sweden)

    Soodabeh Esmaili

    2016-01-01

    Full Text Available Hydrocarbon production from shale has attracted much attention in the recent years. When applied to this prolific and hydrocarbon rich resource plays, our understanding of the complexities of the flow mechanism (sorption process and flow behavior in complex fracture systems - induced or natural leaves much to be desired. In this paper, we present and discuss a novel approach to modeling, history matching of hydrocarbon production from a Marcellus shale asset in southwestern Pennsylvania using advanced data mining, pattern recognition and machine learning technologies. In this new approach instead of imposing our understanding of the flow mechanism, the impact of multi-stage hydraulic fractures, and the production process on the reservoir model, we allow the production history, well log, completion and hydraulic fracturing data to guide our model and determine its behavior. The uniqueness of this technology is that it incorporates the so-called “hard data” directly into the reservoir model, so that the model can be used to optimize the hydraulic fracture process. The “hard data” refers to field measurements during the hydraulic fracturing process such as fluid and proppant type and amount, injection pressure and rate as well as proppant concentration. This novel approach contrasts with the current industry focus on the use of “soft data” (non-measured, interpretive data such as frac length, width, height and conductivity in the reservoir models. The study focuses on a Marcellus shale asset that includes 135 wells with multiple pads, different landing targets, well length and reservoir properties. The full field history matching process was successfully completed using this data driven approach thus capturing the production behavior with acceptable accuracy for individual wells and for the entire asset.

  18. The effect of deformation on two-phase flow through proppant-packed fractured shale samples: A micro-scale experimental investigation

    Science.gov (United States)

    Arshadi, Maziar; Zolfaghari, Arsalan; Piri, Mohammad; Al-Muntasheri, Ghaithan A.; Sayed, Mohammed

    2017-07-01

    then entrained by the flow and partially blocked pore-throat connections within the proppant pack. Deformation of proppant packs resulted in significant changes in waterflood residual oil saturation. In-situ contact angles measured using micro-CT images showed that proppant grains had experienced a drastic alteration of wettability (from strong water-wet to weakly oil-wet) after the medium had been subjected to flow of oil and brine for multiple weeks. Nanometer resolution SEM images captured nano-fractures induced in the shale surfaces during the experiments with mono-layer proppant packing. These fractures improved the effective permeability of the medium and shale/fracture interactions.

  19. Texture and anisotropy analysis of Qusaiba shales

    KAUST Repository

    Kanitpanyacharoen, Waruntorn

    2011-02-17

    Scanning and transmission electron microscopy, synchrotron X-ray diffraction, microtomography and ultrasonic velocity measurements were used to characterize microstructures and anisotropy of three deeply buried Qusaiba shales from the Rub\\'al-Khali basin, Saudi Arabia. Kaolinite, illite-smectite, illite-mica and chlorite show strong preferred orientation with (001) pole figure maxima perpendicular to the bedding plane ranging from 2.4-6.8 multiples of a random distribution (m.r.d.). Quartz, feldspars and pyrite crystals have a random orientation distribution. Elastic properties of the polyphase aggregate are calculated by averaging the single crystal elastic properties over the orientation distribution, assuming a nonporous material. The average calculated bulk P-wave velocities are 6.2 km/s (maximum) and 5.5 km/s (minimum), resulting in a P-wave anisotropy of 12%. The calculated velocities are compared with those determined from ultrasonic velocity measurements on a similar sample. In the ultrasonic experiment, which measures the effects of the shale matrix as well as the effects of porosity, velocities are smaller (P-wave maximum 5.3 km/s and minimum 4.1 km/s). The difference between calculated and measured velocities is attributed to the effects of anisotropic pore structure and to microfractures present in the sample, which have not been taken into account in the matrix averaging. © 2011 European Association of Geoscientists & Engineers.

  20. Anisotropic Thermoplasticty and Strain Localization in Shale

    Science.gov (United States)

    Semnani, S. J.; White, J. A.; Borja, R. I.

    2016-12-01

    Sedimentary rocks such as shale are inherently anisotropic due to their layered structure, and sensitive to temperature changes caused by various engineering applications e.g. carbon sequestration, waste disposal, wellbore drilling, as well as geothermal and heat storage applications. These materials are also prone to strain localization in the form of a shear band when subjected to critical loads. Strain localization is generally considered as a manifestation of material instability, which has been linked traditionally to failure of materials. While isotropic material models simplify the modeling process, they fail to accurately describe the mechanical behavior and onset of instability in anisotropic rocks. We present a thermo-plastic framework for modeling the coupled thermo-mechanical response and for predicting the inception of a shear band in shale using the general framework of critical state plasticity and the specific framework of modified Cam-Clay model. Under the assumption of infinitesimal deformation, the formulation incorporates anisotropy in both elastic and plastic responses. The model is first calibrated using experimental data from triaxial tests to demonstrate its capability in capturing anisotropy in the mechanical response. Subsequently, stress-point simulations of strain localization are carried out under two different conditions, namely, isothermal localization and adiabatic localization. The adiabatic formulation investigates the effect of temperature on localization via thermo-mechanical coupling. Numerical simulations are presented to demonstrate the effect of anisotropy, hardening, and thermal softening on strain localization.

  1. Application of indirect stress measurement techniques (non strain gauge based technology) to quantify stress environments in mines

    CSIR Research Space (South Africa)

    Stacey, TR

    2002-03-01

    Full Text Available Reliable values of in situ stress are essential for the valid modelling of mine layouts. Available non-strain gauge methods are reviewed as potential practical techniques for South African mines. From this review it is concluded that the most...

  2. A Geochemical Method for Determining Heat History of Retorted Shale Oil.

    Science.gov (United States)

    1980-06-01

    porphyrin fraction from oil shale bitumen and the total retorted shale oil. The demetallated porphyrins were separated into etio and phyllo series by silica ...PAGE I. Yield of Porphyrin Fraction from GPC. ..... ...... 9 Il. High Resolution Mass Spectroscopic Results f or Oil Shale Bitumen ...13 Ill. Mass Spectroscopic Data for Shale Oil Bitumen . .. ..... 14 - __ , : , v. =- , . .= 7- , 4 =-- . -.. : -=? - L : T , LIST OF FIGURES

  3. Perform research in process development for hydroretorting of Eastern oil shales: Volume 2, Expansion of the Moving-Bed Hydroretorting Data Base for Eastern oil shales

    Energy Technology Data Exchange (ETDEWEB)

    1989-11-01

    An extensive data base was developed for six Eastern oil shales: Alabama Chattanooga, Indiana New Albany, Kentucky Sunbury, Michigan Antrim, Ohio Cleveland, and Tennessee Chattanooga shales. The data base included the hydroretorting characteristics of the six shales, as well as the retorting characteristics in the presence of synthesis gas and ionized gas. Shale gasification was also successfully demonstrated. Shale fines (20%) can produce enough hydrogen for the hydroretorting of the remaining 80% of the shale. The amount of fines tolerable in a moving bed was also determined. 16 refs., 59 figs., 43 tabs.

  4. Risks to biodiversity from hydraulic fracturing for natural gas in the Marcellus and Utica shales.

    Science.gov (United States)

    Kiviat, Erik

    2013-05-01

    High-volume horizontal hydraulic fracturing (HVHHF) for mining natural gas from the Marcellus and Utica shales is widespread in Pennsylvania and potentially throughout approximately 280,000 km(2) of the Appalachian Basin. Physical and chemical impacts of HVHHF include pollution by toxic synthetic chemicals, salt, and radionuclides, landscape fragmentation by wellpads, pipelines, and roads, alteration of stream and wetland hydrology, and increased truck traffic. Despite concerns about human health, there has been little study of the impacts on habitats and biota. Taxa and guilds potentially sensitive to HVHHF impacts include freshwater organisms (e.g., brook trout, freshwater mussels), fragmentation-sensitive biota (e.g., forest-interior breeding birds, forest orchids), and species with restricted geographic ranges (e.g., Wehrle's salamander, tongue-tied minnow). Impacts are potentially serious due to the rapid development of HVHHF over a large region. © 2013 New York Academy of Sciences.

  5. Demonstration projects for coalbed methane and Devonian shale gas: Final report. [None

    Energy Technology Data Exchange (ETDEWEB)

    Verrips, A.M.; Gustavson, J.B.

    1987-04-01

    In 1979, the US Department of Energy provided the American Public Gas Association (APGA) with a grant to demonstrate the feasibility of bringing unconventional gas such as methane produced from coalbeds or Devonian Shale directly into publicly owned utility system distribution lines. In conjunction with this grant, a seven-year program was initiated where a total of sixteen wells were drilled for the purpose of providing this untapped resource to communities who distribute natural gas. While coalbed degasification ahead of coal mining was already a reality in several parts of the country, the APGA demonstration program was aimed at actual consumer use of the gas. Emphasis was therefore placed on degasification of coals with high methane gas content and on utilization of conventional oil field techniques. 13 figs.

  6. Shale oil specialty markets: Screening survey for United States applications

    Energy Technology Data Exchange (ETDEWEB)

    1987-12-01

    EG and G requested J. E. Sinor Consultants Inc. to carry out an initial screening study on the possibilities for producing specialty chemicals from oil shale. Raw shale oil is not an acceptable feedstock to refineries and there are not enough user of heavy fuel oil in the western oil shale region to provide a dependable market. The only alternatives are to hydrotreat the oil, or else ship it long distances to a larger market area. Either of these alternatives results in a cost penalty of several dollars per barrel. Instead of attempting to enter the large-volume petroleum products market, it was hypothesized that a small shale oil facility might be able to produce specialty chemicals with a high enough average value to absorb the high costs of shipping small quantities to distant markets and still provide a higher netback to the plant site than sales to the conventional petroleum products market. This approach, rather than attempting to refine shale oil or to modify its characteristics to satisfy the specifications for petroleum feedstocks or products, focuses instead on those particular characteristics which distinguish shale oil from petroleum, and attempts to identify applications which would justify a premium value for those distinctive characteristics. Because byproducts or specialty chemicals production has been a prominent feature of oil shale industries which have flourished for periods of time in various countries, a brief review of those industries provides a starting point for this study. 9 figs., 32 tabs.

  7. A comprehensive environmental impact assessment method for shale gas development

    Directory of Open Access Journals (Sweden)

    Renjin Sun

    2015-03-01

    Full Text Available The great success of US commercial shale gas exploitation stimulates the shale gas development in China, subsequently, the corresponding supporting policies were issued in the 12th Five-Year Plan. But from the experience in the US shale gas development, we know that the resulted environmental threats are always an unavoidable issue, but no uniform and standard evaluation system has yet been set up in China. The comprehensive environment refers to the combination of natural ecological environment and external macro-environment. In view of this, we conducted a series of studies on how to set up a comprehensive environmental impact assessment system as well as the related evaluation methodology and models. First, we made an in-depth investigation into shale gas development procedures and any possible environmental impacts, and then compared, screened and modified environmental impact assessment methods for shale gas development. Also, we established an evaluating system and assessment models according to different status of the above two types of environment: the correlation matrix method was employed to assess the impacts on natural ecological environment and the optimization distance method was modified to evaluate the impacts on external macro-environment. Finally, we substitute the two subindexes into the comprehensive environmental impact assessment model and achieved the final numerical result of environmental impact assessment. This model can be used to evaluate if a shale gas project has any impact on environment, compare the impacts before and after a shale gas development project, or the impacts of different projects.

  8. Automation for underwater mine recognition: current trends and future strategy

    Science.gov (United States)

    Stack, Jason

    2011-06-01

    The purpose of this paper is to define the vision and future strategy for advancing the use of automation in underwater mine recognition. The technical portion of this strategy is founded on the principle of adapting the automation in situ based on a highly variable environment / context and the occasional availability of the human operator. To frame this strategy, a survey of past and current algorithm development for underwater mine recognition is presented and includes a detailed description on adaptive algorithms. This discussion is motivated by illustrating the extreme variability in the underwater environment and that performance estimation techniques are now emerging that are capable of quantifying these variations in situ. It is the in situ linkage of performance estimation with adaptive recognition that forms one of the key technological enablers of this future strategy. The non-technical portion of this strategy is centered on enabling an effective human-machine team. Enabling this teaming relationship involves both gaining trust and establishing an overall support system that is amenable to such human-machine interactions. Aspects of trust include both individual trust and institutional trust, and a path for gaining both is discussed. Overall aspects of the support system are highlighted and include standards for data and interoperability, network-centric software architectures, and issues in proliferating knowledge that is learned in situ by multiple distributed algorithms. This paper concludes with an articulation of several important and timely research questions concerning automation for underwater mine recognition.

  9. In-situ stress measurements at DOE's multiwell experiment site, Mesaverde group, Rifle, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Warpinski, N.R.; Branagan, P.; Wilmer, R.

    1983-01-01

    Measurements of the vertical distribution of the minimum principal in situ stress in the lower Mesaverde group (7300 to 8100 ft depth, 2225 to 2470 m) at DOE's Multi-Well Experiment site have been made by conducting small-volume, hydraulic-fracture stress tests through perforations. Accurate, reproducible results were obtained by conducting a number of repeat injections in each zone of interest using a specially designed pump system, modified high-resolution electronic equipment, and a down-hole shut-off tool with a bottom-hole pressure transducer. Stress tests were conducted in marine sandstones and shales as well as a coal, mudstone, and sandstone in a paludal depositional environment. These tests provide a detailed stress distribution in this region. 19 references.

  10. IN SITU URANIUM STABILIZATION BY MICROBIAL METABOLITES

    Energy Technology Data Exchange (ETDEWEB)

    Turick, C; Anna Knox, A; Chad L Leverette,C; Yianne Kritzas, Y

    2006-11-29

    Soil contaminated with U was the focus of this study in order to develop in-situ, U bio-immobilization technology. We have demonstrated microbial production of a metal chelating biopolymer, pyomelanin, in U contaminated soil from the Tims Branch area of the Department of Energy (DOE) Savannah River Site (SRS) as a result of tyrosine amendments. Bacterial densities of pyomelanin producers were >106 cells/g wet soil. Pyomelanin demonstrated U chelating and mineral binding capacities at pH 4 and 7. In laboratory studies, in the presence of goethite or illite, pyomelanin enhanced U sequestration by these minerals. Tyrosine amended soils in field tests demonstrated increased U sequestration capacity following pyomelanin production up to 13 months after tyrosine treatments.

  11. Ductal Carcinoma In Situ of the Breast

    Directory of Open Access Journals (Sweden)

    Richard J. Lee

    2012-01-01

    Full Text Available Ductal carcinoma in situ (DCIS of the breast represents a complex, heterogeneous pathologic condition in which malignant epithelial cells are confined within the ducts of the breast without evidence of invasion. The increased use of screening mammography has led to a significant shift in the diagnosis of DCIS, accounting for approximately 27% of all newly diagnosed cases of breast cancer in 2011, with an overall increase in incidence. As the incidence of DCIS increases, the treatment options continue to evolve. Consistent pathologic evaluation is crucial in optimizing treatment recommendations. Surgical treatment options include breast-conserving surgery (BCS and mastectomy. Postoperative radiation therapy in combination with breast-conserving surgery is considered the standard of care with demonstrated decrease in local recurrence with the addition of radiation therapy. The role of endocrine therapy is currently being evaluated. The optimization of diagnostic imaging, treatment with regard to pathological risk assessment, and the role of partial breast irradiation continue to evolve.

  12. In situ soil remediation: Bacteria or fungi?

    Energy Technology Data Exchange (ETDEWEB)

    Cutright, T.J.; Lee, S. [Univ. of Akron, OH (United States). Dept. of Chemical Engineering

    1995-07-01

    Contamination of the environment is not a new problem. For most of recorded history, the unwanted byproducts of industrial and residential processes have been dumped into unlined pits or nearby streams. Although disposal techniques have greatly improved, significant quantities of hazardous materials are still being released to the environment via accidental spills and leaking underground storage tanks. One particular group of contaminants of critical environmental concern is polycyclic aromatic hydrocarbons (PAHs). PAH-contaminated sites typically cover large areas; therefore, the development of in situ remediation techniques such as bioremediation is strongly emphasized. In situations when inherent microorganisms are not capable of degrading the contaminants, foreign strains must be used. Bioremediation experiments were conducted to compare the remediation efficiencies of a bacteria and a fungus for an industrially PAH contaminated soil. Specifically, the use of three supplemental nutrient solutions were investigated in conjunction with the bacteria Achromobacter sp. and fungus Cunninghamella echinulata var. elegans.

  13. Support Routines for In Situ Image Processing

    Science.gov (United States)

    Deen, Robert G.; Pariser, Oleg; Yeates, Matthew C.; Lee, Hyun H.; Lorre, Jean

    2013-01-01

    This software consists of a set of application programs that support ground-based image processing for in situ missions. These programs represent a collection of utility routines that perform miscellaneous functions in the context of the ground data system. Each one fulfills some specific need as determined via operational experience. The most unique aspect to these programs is that they are integrated into the large, in situ image processing system via the PIG (Planetary Image Geometry) library. They work directly with space in situ data, understanding the appropriate image meta-data fields and updating them properly. The programs themselves are completely multimission; all mission dependencies are handled by PIG. This suite of programs consists of: (1)marscahv: Generates a linearized, epi-polar aligned image given a stereo pair of images. These images are optimized for 1-D stereo correlations, (2) marscheckcm: Compares the camera model in an image label with one derived via kinematics modeling on the ground, (3) marschkovl: Checks the overlaps between a list of images in order to determine which might be stereo pairs. This is useful for non-traditional stereo images like long-baseline or those from an articulating arm camera, (4) marscoordtrans: Translates mosaic coordinates from one form into another, (5) marsdispcompare: Checks a Left Right stereo disparity image against a Right Left disparity image to ensure they are consistent with each other, (6) marsdispwarp: Takes one image of a stereo pair and warps it through a disparity map to create a synthetic opposite- eye image. For example, a right eye image could be transformed to look like it was taken from the left eye via this program, (7) marsfidfinder: Finds fiducial markers in an image by projecting their approximate location and then using correlation to locate the markers to subpixel accuracy. These fiducial markets are small targets attached to the spacecraft surface. This helps verify, or improve, the

  14. In-situ trainable intrusion detection system

    Science.gov (United States)

    Symons, Christopher T.; Beaver, Justin M.; Gillen, Rob; Potok, Thomas E.

    2016-11-15

    A computer implemented method detects intrusions using a computer by analyzing network traffic. The method includes a semi-supervised learning module connected to a network node. The learning module uses labeled and unlabeled data to train a semi-supervised machine learning sensor. The method records events that include a feature set made up of unauthorized intrusions and benign computer requests. The method identifies at least some of the benign computer requests that occur during the recording of the events while treating the remainder of the data as unlabeled. The method trains the semi-supervised learning module at the network node in-situ, such that the semi-supervised learning modules may identify malicious traffic without relying on specific rules, signatures, or anomaly detection.

  15. In situ preparation of Calcium hydroxide films

    Energy Technology Data Exchange (ETDEWEB)

    Dahle, S.; Voigts, F. [Institut fuer Physik und Physikalische Technologien, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany); Maus-Friedrichs, W., E-mail: w.maus-friedrichs@pe.tu-clausthal.de [Institut fuer Physik und Physikalische Technologien, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany); Clausthaler Zentrum fuer Materialtechnik, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany)

    2011-10-31

    The in situ preparation of Calcium hydroxide films in an ultra high vacuum (UHV) is constrained by the decomposition of species at the surface and the absence of OH bulk diffusion. Therefore, it is not possible to prepare such films simply by water exposure to a Calcium layer. We present four different approaches for the preparation of Ca(OH){sub 2} films in an UHV. Two of these methods are found to be ineffective for the preparation, the other two are shown to produce Calcium hydroxide films. Both of the two effective procedures make use of H{sub 2} gas exposure. Metastable Induced Electron Spectroscopy, Ultraviolet Photoelectron Spectroscopy, and X-ray Photoelectron Spectroscopy are employed to verify quality and purity of the films.

  16. In situ preparation of calcium carbonate films

    Energy Technology Data Exchange (ETDEWEB)

    Dahle, S. [Clausthaler Zentrum fuer Materialtechnik, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany); Institut fuer Physik und Physikalische Technologien, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany); Voigts, F. [Institut fuer Physik und Physikalische Technologien, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany); Maus-Friedrichs, W., E-mail: w.maus-friedrichs@pe.tu-clausthal.de [Clausthaler Zentrum fuer Materialtechnik, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany); Institut fuer Physik und Physikalische Technologien, Technische Universitaet Clausthal, Leibnizstrasse 4, 38678 Clausthal-Zellerfeld (Germany)

    2012-01-01

    The in situ preparation of calcium carbonate films in an ultra high vacuum (UHV) is inhibited by the decomposition of CO{sub 2} molecules at the surface and the absence of CO{sub 2} bulk diffusion. Therefore, it is not possible to prepare such films simply by CO{sub 2} exposure to a calcium layer. We investigated different approaches for the preparation of CaCO{sub 3} films in an UHV. Among these, only the simultaneous evaporation of Ca atoms in a mixed O{sub 2} and CO{sub 2} atmosphere is able to produce well defined stoichiometric calcium carbonate films. Metastable Induced Electron Spectroscopy, Ultraviolet Photoelectron Spectroscopy and X-ray Photoelectron Spectroscopy are employed to verify quality and purity of the films.

  17. THE PELLETS APPLICATION IN LABORATORY RESEARCHING OF INHIBITIVE MUD/SHALE INTERACTION

    Directory of Open Access Journals (Sweden)

    Borivoje Pašić

    2012-12-01

    Full Text Available Wellbore instability appears to be a serious problem during drilling process through shale. Shales instability cause basically comes out of its mineralogical composition (especially clay minerals content and physico-chemical properties. Many research activities about shale instability causes and shale properties (affecting shale behavior during interaction with water phase of different drilling muds definition have been carried out by now. In these laboratory tests were used original shales samples given by coring process or collecting shale cuttings from shale shakers, and different shale samples from outcrop. From this reason is very difficult compare laboratory tests results given by different authors. Possible solution is use artificial shale samples (pellets with exact mineralogical composition, enabling extensive laboratory tests and tests results comparison. In this paper presented laboratory tests of pellets swelling in inhibitive muds (the paper is published in Croatian.

  18. In Situ Field Testing of Processes

    Energy Technology Data Exchange (ETDEWEB)

    J. Wang

    2001-12-14

    The purpose of this Analysis/Model Report (AMR) is to update and document the data and subsequent analyses from ambient field-testing activities performed in underground drifts of the Yucca Mountain Site Characterization Project (YMP). This revision updates data and analyses presented in the initial issue of this AMR. This AMR was developed in accordance with the ''Technical Work Plan for Unsaturated Zone (UZ) Flow and Transport Process Model Report'' and ''Technical Work Plan for UZ Flow, Transport, and Coupled Processes Process Model Report. These activities were performed to investigate in situ flow and transport processes. The evaluations provide the necessary framework to: (1) refine and confirm the conceptual model of matrix and fracture processes in the unsaturated zone (UZ) and (2) analyze the impact of excavation (including use of construction water and effect of ventilation) on the UZ flow and transport processes. This AMR is intended to support revisions to ''Conceptual and Numerical Models for UZ Flow and Transport'' and ''Unsaturated Zone Flow and Transport Model Process Model Report''. In general, the results discussed in this AMR are from studies conducted using a combination or a subset of the following three approaches: (1) air-injection tests, (2) liquid-release tests, and (3) moisture monitoring using in-drift sensors or in-borehole sensors, to evaluate the impact of excavation, ventilation, and construction-water usage on the surrounding rocks. The liquid-release tests and air-injection tests provide an evaluation of in situ fracture flow and the competing processes of matrix imbibition. Only the findings from testing and data not covered in the ''Seepage Calibration Model and Seepage Testing Data'' are analyzed in detail in the AMR.

  19. Analysis of the environmental control technology for oil shale development

    Energy Technology Data Exchange (ETDEWEB)

    de Nevers, N.; Eckhoff, D.; Swanson, S.; Glenne, B.; Wagner, F.

    1978-02-01

    The environmental control technology proposed in the various oil shale projects which are under development are examined. The technologies for control of air pollution, water pollution, and for the disposal, stabilization, and vegetation of the processed shale were thoroughly investigated. Although some difficulties may be encountered in any of these undertakings, it seems clear that the air and water pollution problems can be solved to meet any applicable standard. There are no published national standards against which to judge the stabilization and vegetation of the processed shale. However, based on the goal of producing an environmentally and aesthetically acceptable finished processed shale pile, it seems probable that this can be accomplished. It is concluded that the environmental control technology is available to meet all current legal requirements. This was not the case before Colorado changed their applicable Air Pollution regulations in August of 1977; the previous ones for the oil shale region were sufficiently stringent to have caused a problem for the current stage of oil shale development. Similarly, the federal air-quality, non-deterioration regulations could be interpreted in the future in ways which would be difficult for the oil shale industry to comply with. The Utah water-quality, non-deterioration regulations could also be a problem. Thus, the only specific regulations which may be a problem are the non-deterioration parts of air and water quality regulations. The unresolved areas of environmental concern with oil shale processing are mostly for the problems not covered by existing environmental law, e.g., trace metals, polynuclear organics, ground water-quality changes, etc. These may be problems, but no evidence is yet available that these problems will prevent the successful commercialization of oil shale production.

  20. Shale Gas Geomechanics for Development and Performance of Unconventional Reservoirs

    Science.gov (United States)

    Domonik, Andrzej; Łukaszewski, Paweł; Wilczyński, Przemysław; Dziedzic, Artur; Łukasiak, Dominik; Bobrowska, Alicja

    2017-04-01

    Mechanical properties of individual shale formations are predominantly determined by their lithology, which reflects sedimentary facies distribution, and subsequent diagenetic and tectonic alterations. Shale rocks may exhibit complex elasto-viscoplastic deformation mechanisms depending on the rate of deformation and the amount of clay minerals, also bearing implications for subcritical crack growth and heterogeneous fracture network development. Thus, geomechanics for unconventional resources differs from conventional reservoirs due to inelastic matrix behavior, stress sensitivity, rock anisotropy and low matrix permeability. Effective horizontal drilling and hydraulic fracturing technologies are required to obtain and maintain high performance. Success of these techniques strongly depends on the geomechanical investigations of shales. An inelastic behavior of shales draws increasing attention of investigators [1], due to its role in stress relaxation between fracturing phases. A strong mechanical anisotropy in the vertical plane and a lower and more variable one in the horizontal plane are characteristic for shale rocks. The horizontal anisotropy plays an important role in determining the direction and effectiveness of propagation of technological hydraulic fractures. Non-standard rock mechanics laboratory experiments are being applied in order to obtain the mechanical properties of shales that have not been previously studied in Poland. Novel laboratory investigations were carried out to assess the creep parameters and to determine time-dependent viscoplastic deformation of shale samples, which can provide a limiting factor to tectonic stresses and control stress change caused by hydraulic fracturing. The study was supported by grant no.: 13-03-00-501-90-472946 "An integrated geomechanical investigation to enhance gas extraction from the Pomeranian shale formations", funded by the National Centre for Research and Development (NCBiR). References: Ch. Chang M. D

  1. Exploration and Mining Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2002-09-01

    This Exploration and Mining Technology Roadmap represents the third roadmap for the Mining Industry of the Future. It is based upon the results of the Exploration and Mining Roadmap Workshop held May 10 ñ 11, 2001.

  2. Northern Trust Mines

    Science.gov (United States)

    The United States and the Navajo Nation entered into settlement agreements that provide funds to conduct investigations and any needed cleanup at 16 of the 46 priority mines, including six mines in the Northern Abandoned Uranium Mine Region.

  3. Coal Mine Permit Boundaries

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — ESRI ArcView shapefile depicting New Mexico coal mines permitted under the Surface Mining Control and Reclamation Act of 1977 (SMCRA), by either the NM Mining these...

  4. Ghana Mining Journal

    African Journals Online (AJOL)

    ... in the Ghana mining journal: Geology and Mineral Exploration, Mining, Quarrying, Geomechanics, Groundwater Studies, Hydrocarbon Development, Mineral Processing, Metallurgy, Material Science, Mineral Management Policies, Mineral Economics, Environmental Aspects, Computer Applications and Mining Education.

  5. Use of cyanobacteria for in-situ resource use in space applications

    Science.gov (United States)

    Olsson-Francis, Karen; Cockell, Charles S.

    2010-08-01

    The regolith of other planetary bodies, such as the Moon and Mars, is rich in inorganic elements that could potentially be exploited for space applications. Lithotrophic microorganisms that are capable of utilising rocks as a growth substrate, and facilitate the extraction of elements, are ideal candidates for in-situ resource use. Of particular interest are the cyanobacteria, which have been suggested for applications, such as oxygen, fuel and biomass production, nutrient acquisition, and feedstock provisions. In this study, Gloeocapsa strain OU_20, isolated from a rock-dwelling community exposed to low Earth orbit; Leptolyngbya strain OU_13 and Phormidium strain OU_10, both isolated from a rock-dwelling community exposed to Mars simulated conditions; Chroococcidiopsis 029; Arthrospira platensis; Synechococcus elongatus; and Anabaena cylindrica, were examined as potential organisms for space in-situ resource use. Volcanic rocks, including basalt (low in SiO 2) analogous to martian and lunar basalt, rhyolite (high in SiO 2), and anorthosite analogous to lunar regolith were used as growth substrates. The growth rate and rock dissolution were significantly lower with rhyolite demonstrating the importance of silica content in defining the potential for in-situ resource use. Biological weathering resulted in the release of bio-essential elements from the rock matrix, highlighting the potential of cyanobacteria for applications such as bio-mining and nutrient acquisition, on other planets. A. cylindrica produced the maximum biomass with the three rock-types and the optimal value was obtained with the basalt. Exposure experiments demonstrated that A. cylindrica, Chroococcidiopsis 029, Gloeocapsa strain OU_20, Phormidium strain OU_10, and Leptolyngbya strain OU_13 were able to survive 28 days of exposure to desiccation and Mars simulated conditions, which is beneficial in case of system malfunction and for storage. The results from this study indicate that cyanobacteria

  6. In-situ gelling polymers for biomedical applications

    CERN Document Server

    2015-01-01

    This book presents the research involving in situ gelling polymers and can be used as a guidebook for academics, industrialists and postgraduates interested in this area. This work summaries the academic contributions from the top authorities in the field and explore the fundamental principles of in situ gelling polymeric networks, along with examples of their major applications. This book aims to provide an up-to-date resource of in situ gelling polymer research.

  7. Review of Hydraulic Fracturing for Preconditioning in Cave Mining

    Science.gov (United States)

    He, Q.; Suorineni, F. T.; Oh, J.

    2016-12-01

    Hydraulic fracturing has been used in cave mining for preconditioning the orebody following its successful application in the oil and gas industries. In this paper, the state of the art of hydraulic fracturing as a preconditioning method in cave mining is presented. Procedures are provided on how to implement prescribed hydraulic fracturing by which effective preconditioning can be realized in any in situ stress condition. Preconditioning is effective in cave mining when an additional fracture set is introduced into the rock mass. Previous studies on cave mining hydraulic fracturing focused on field applications, hydraulic fracture growth measurement and the interaction between hydraulic fractures and natural fractures. The review in this paper reveals that the orientation of the current cave mining hydraulic fractures is dictated by and is perpendicular to the minimum in situ stress orientation. In some geotechnical conditions, these orientation-uncontrollable hydraulic fractures have limited preconditioning efficiency because they do not necessarily result in reduced fragmentation sizes and a blocky orebody through the introduction of an additional fracture set. This implies that if the minimum in situ stress orientation is vertical and favors the creation of horizontal hydraulic fractures, in a rock mass that is already dominated by horizontal joints, no additional fracture set is added to that rock mass to increase its blockiness to enable it cave. Therefore, two approaches that have the potential to create orientation-controllable hydraulic fractures in cave mining with the potential to introduce additional fracture set as desired are proposed to fill this gap. These approaches take advantage of directional hydraulic fracturing and the stress shadow effect, which can re-orientate the hydraulic fracture propagation trajectory against its theoretical predicted direction. Proppants are suggested to be introduced into the cave mining industry to enhance the

  8. Shale: an overlooked option for US nuclear waste disposal

    Science.gov (United States)

    Neuzil, Christopher E.

    2014-01-01

    Toss a dart at a map of the United States and, more often than not, it will land where shale can be found underground. A drab, relatively featureless sedimentary rock that historically attracted little interest, shale (as used here, the term includes clay and a range of clay-rich rocks) is entering Americans’ consciousness as a new source of gas and oil. But shale may also offer something entirely different—the ability to safely and permanently house high-level nuclear waste.

  9. Shale gas production: potential versus actual greenhouse gas emissions

    OpenAIRE

    O'Sullivan, Francis Martin; Paltsev, Sergey

    2012-01-01

    Estimates of greenhouse gas (GHG) emissions from shale gas production and use are controversial. Here we assess the level of GHG emissions from shale gas well hydraulic fracturing operations in the United States during 2010. Data from each of the approximately 4000 horizontal shale gas wells brought online that year are used to show that about 900 Gg CH[subscript 4] of potential fugitive emissions were generated by these operations, or 228 Mg CH[subscript 4] per well—a figure inappropriately ...

  10. Shale Gas and Oil in Germany - Resources and Environmental Impacts

    Science.gov (United States)

    Ladage, Stefan; Blumenberg, Martin; Houben, Georg; Pfunt, Helena; Gestermann, Nicolai; Franke, Dieter; Erbacher, Jochen

    2017-04-01

    In light of the controversial debate on "unconventional" oil and gas resources and the environmental impacts of "fracking", the Federal Institute for Geosciences and Natural Resources (BGR) conducted a comprehensive resource assessment of shale gas and light tight oil in Germany and studied the potential environmental impacts of shale gas development and hydraulic fracturing from a geoscientific perspective. Here, we present our final results (BGR 2016), incorporating the majority of potential shale source rock formations in Germany. Besides shale gas, light tight oil has been assessed. According to our set of criteria - i.e. thermal maturity 0.6-1.2 %vitrinite reflectance (VR; oil) and >1.2 % VR (gas) respectively, organic carbon content > 2%, depth between 500/1000 m and 5000 m as well as a net thickness >20 m - seven potentially generative shale formations were indentified, the most important of them being the Lower Jurassic (Toarcian) Posidonia shale with both shale gas and tight oil potential. The North German basin is by far the most prolific basin. The resource assessment was carried out using a volumetric in-place approach. Variability inherent in the input parameters was accounted for using Monte-Carlo simulations. Technically recoverable resources (TRR) were estimated using recent, production-based recovery factors of North American shale plays and also employing Monte-Carlo simulations. In total, shale gas TRR range between 320 and 2030 bcm and tight oil TRR between 13 and 164 Mio. t in Germany. Tight oil potential is therefore considered minor, whereas the shale gas potential exceeds that of conventional resources by far. Furthermore an overview of numerical transport modelling approaches concerning environmental impacts of the hydraulic fracturing is given. These simulations are based on a representative lithostratigraphy model of the North-German basin, where major shale plays can be expected. Numerical hydrogeological modelling of frac fluid

  11. In-Situ Stress Measurements at U. S. DOE's Multiwell Experiment Site, Mesaverde Group, Rifle, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Warpinski, N.R.; Branagan, P.; Wilmer, R.

    1985-03-01

    Vertical distribution measurements of the minimum principal in-situ stress in the lower Mesaverde group (7,300to 8,100-ft (2225- to 2470-m) depth) at the U.S. DOE's Multiwell Experiment (MWX) site have been made by conducting small-volume, hydraulic-fracture stress tests through perforations. Accurate, reproducible results were obtained by conducting repeated injections in each zone of interest with a specially designed pump system, modified high-resolution electronic equipment, and a downhole shut-off tool with a bottomhole pressure (BHP) transducer. Stress tests were conducted in marine sandstones and shales as well as in coal, mudstone, and sandstone in a paludal depositional environment; these tests provide a detailed stress distribution in this region. The stress magnitudes were found to depend on lithology. Marine shales above and below the blanket sands have large horizontal stresses that are nearly lithostatic, with a fracture gradient greater than 1.0 psi/ft (23 kPa/m). This indicates that these rocks do not behave elastically and processes such as creep and possibly fracturing are the dominant mechanisms controlling the stress state. Sandstones and siltstones have much lower stresses, with a fracture gradient of 0.85 to 0.9 psi/ft (19 to 20 kPa/m). Containment of hydraulic fractures would be expected under these conditions. Only three data points were obtained from the paludal interval; no significant stress differences were observed in the different lithologies.

  12. In-situ stress measurements at DOE's Multi-Well Experiment site, Mesaverde group, Rifle, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Warpinski, N.R.; Branagan, P.; Wilmer, R.

    1983-10-01

    Measurements of the vertical distribution of the minimum principal in-situ stress in the lower Mesaverde group (7300-8100 ft depth, 2225-2470 m) at DOE's Multi-Well Experiment site have been made by conducting small-volume, hydraulic-fracture stress tests through perforations. Accurate, reproducible results were obtained by conducting a number of repeat injections in each zone of interest using a specially designed pump system, modified high-resolution electronic equipment, and a down-hole shut-off tool with a bottom-hole pressure transducer. Stress tests were conducted in marine sandstones and shales as well as a coal, mudstone, and sandstone in a paludal depositional environment; these tests provide a detailed stress distribution in this region. The stress magnitudes were found to be dependent on lithology. Marine shales above and below the blanket sands have large horizontal stresses-near lithostatic with a frac gradient greater than 1.0 psi/ft (23 kPa/m). This indicates that these rocks do not behave elastically and processes such as creep and possibly fracturing are the dominant mechanisms controlling the stress state. On the other hand, sandstones and siltstones have much lower stresses with a frac gradient of 0.85-0.9 psi/ft (19-20 kPa/m). Containment of hydraulic fractures would be expected under these conditions.

  13. RADIONUCLIDES DISTRIBUTION NEAR FORMER URANIUM MINING

    Directory of Open Access Journals (Sweden)

    D. A. Zaredinov

    2016-01-01

    Full Text Available The paper shows, that radionuclides from the stony rocks of uranium mines can be leached by atmospheric precipitations. In acid conditions, a degree of leaching is greater.Goal. The aim of this investigation was to study the distribution of radionuclides in uranium minings and their impact on the environmental contamination.Materials and methods. The study was carried out in two stages. In the first stage, a blade of rock was mixed with distilled water in proportions of 0,3 kg of gravel and 1 liter of water. After thirty days of soaking, water was sent to the gamma-spectrometric analysis to Canberra’s spectrometer (USA with a high-purity germanium detector. In the second stage, we carried out the similar experiment with water, wich was acidified to pH = 3. Contamination levels of areas near the in-situ leaching mine were determined. Intervention levels were used to estimate risk and possible water consumption by the population. Estimations were carried out taking into account the combined presence of several radionuclides in the water.Results. The results of these studies have shown that the distribution of radionuclides from the source of the contamination is about 360 meters during the 30 y period. The stream, along which samples of soil were collected and studied, was formed by the miner waters that flow along small ruts towards a village, thereby increasing the likelihood of water use by the public.Conclusions. The uranium mines are the source of radioactive contamination. Radionuclides are distributed due to the erosion of rocks and leached out of the stony rock by precipitations. The extent of leaching is significantly increased in an acidic environment, which takes place near the in-situ leaching mines.

  14. Identifying equatorial ionospheric irregularities using in situ ion drifts

    National Research Council Canada - National Science Library

    R. A. Stoneback; R. A. Heelis

    2014-01-01

    Previous climatological investigations of ionospheric irregularity occurrence in the equatorial ionosphere have utilized in situ measurements of plasma density to identify the presence of an irregularity...

  15. Investigating the Potential Impacts of Energy Production in the Marcellus Shale Region Using the Shale Network Database

    Science.gov (United States)

    Brantley, S.; Pollak, J.

    2016-12-01

    The Shale Network's extensive database of water quality observations in the Marcellus Shale region enables educational experiences about the potential impacts of resource extraction and energy production with real data. Through tools that are open source and free to use, interested parties can access and analyze the very same data that the Shale Network team has used in peer-reviewed publications about the potential impacts of hydraulic fracturing on water. The development of the Shale Network database has been made possible through efforts led by an academic team and involving numerous individuals from government agencies, citizen science organizations, and private industry. With these tools and data, the Shale Network team has engaged high school students, university undergraduate and graduate students, as well as citizens so that all can discover how energy production impacts the Marcellus Shale region, which includes Pennsylvania and other nearby states. This presentation will describe these data tools, how the Shale Network has used them in educational settings, and the resources available to learn more.

  16. The Potential of Ketungau and Silat Shales in Ketungau and Melawi Basins, West Kalimantan: For Oil Shale and Shale Gas Exploration

    Directory of Open Access Journals (Sweden)

    Lauti Dwita Santy

    2014-07-01

    Full Text Available DOI: 10.17014/ijog.v8i1.154The Ketungau and Melawi Basins, in West Kalimantan, are Tertiary intramontane basins of which the potential for economic conventional oil and gas discoveries have not previously been confirmed. The Ketungau Basin is bordered by the Melawi Basin in the south. Besides non-ideal trapping mechanisms, another major problem in these basins is source rock maturation. Nevertheless, both basins are promising to be explored for oil shale and shale gas energy resources. Therefore, the aim of this paper is to give some perspectives on their source rocks, as an input for the evaluation of the potential of unconventional oil and gas. About twenty samples collected from the Ketungau and Melawi Basins were analyzed using pyrolysis and organic petrographic methods. The results show a poor to good quality of source rock potential. The Ketungau shale, which is the main source rock in the Ketungau Basin, is dominated by type III, immature, and gas prone kerogen. The Silat shale, which is the main source rock in the Melawi Basin, is dominated by type II, immature to early mature, mixed gas, and oil prone kerogen. In the field, Ketungau and Silat Formations have a widespread distribution, and are typically 900 m to 1000 m thick. Both the Ketungau and Silat shales occur within synclinal structures, which have a poor trapping mechanism for conventional oil or gas targets, but are suitable for oil shale and shale gas exploration. This early stage of research clearly shows good potential for the future development of unconventional energy within the Ketungau and Melawi Basins.

  17. Assessing the adsorption properties of shales

    Science.gov (United States)

    Pini, Ronny

    2015-04-01

    Physical adsorption refers to the trapping of fluid molecules at near liquid-like densities in the pores of a given adsorbent material. Fine-grained rocks, such as shales, contain a significant amount of nanopores that can significantly contribute to their storage capacity. As a matter of fact, the current ability to extract natural gas that is adsorbed in the rock's matrix is limited, and current technology focuses primarily on the free gas in the fractures (either natural or stimulated), thus leading to recovery efficiencies that are very low. Shales constitute also a great portion of so-called cap-rocks above potential CO2 sequestration sites; hereby, the adsorption process may limit the CO2 mobility within the cap-rock, thus minimizing the impact of leakage on the whole operation. Whether it is an unconventional reservoir or a cap-rock, understanding and quantifying the mechanisms of adsorption in these natural materials is key to improve the engineering design of subsurface operations. Results will be presented from a laboratory study that combines conventional techniques for the measurement of adsorption isotherms with novel methods that allows for the imaging of adsorption using x-rays. Various nanoporous materials are considered, thus including rocks, such as shales and coals, pure clay minerals (a major component in mudrocks) and engineered adsorbents with well-defined nanopore structures, such as zeolites. Supercritical CO2 adsorption isotherms have been measured with a Rubotherm Magnetic Suspension balance by covering the pressure range 0.1-20~MPa. A medical x-ray CT scanner has been used to identify three-dimensional patterns of the adsorption properties of a packed-bed of adsorbent, thus enabling to assess the spatial variability of the adsorption isotherm in heterogeneous materials. The data are analyzed by using thermodynamically rigorous measures of adsorption, such as the net- and excess adsorbed amounts and a recently developed methodology is

  18. Iron isotope biogeochemistry of Neoproterozoic marine shales

    Science.gov (United States)

    Kunzmann, Marcus; Gibson, Timothy M.; Halverson, Galen P.; Hodgskiss, Malcolm S. W.; Bui, Thi Hao; Carozza, David A.; Sperling, Erik A.; Poirier, André; Cox, Grant M.; Wing, Boswell A.

    2017-07-01

    Iron isotopes have been widely applied to investigate the redox evolution of Earth's surface environments. However, it is still unclear whether iron cycling in the water column or during diagenesis represents the major control on the iron isotope composition of sediments and sedimentary rocks. Interpretation of isotopic data in terms of oceanic redox conditions is only possible if water column processes dominate the isotopic composition, whereas redox interpretations are less straightforward if diagenetic iron cycling controls the isotopic composition. In the latter scenario, iron isotope data is more directly related to microbial processes such as dissimilatory iron reduction. Here we present bulk rock iron isotope data from late Proterozoic marine shales from Svalbard, northwestern Canada, and Siberia, to better understand the controls on iron isotope fractionation in late Proterozoic marine environments. Bulk shales span a δ 56Fe range from -0.45 ‰ to +1.04 ‰ . Although δ 56Fe values show significant variation within individual stratigraphic units, their mean value is closer to that of bulk crust and hydrothermal iron in samples post-dating the ca. 717-660 Ma Sturtian glaciation compared to older samples. After correcting for the highly reactive iron content in our samples based on iron speciation data, more than 90% of the calculated δ 56Fe compositions of highly reactive iron falls in the range from ca. -0.8 ‰ to +3 ‰ . An isotope mass-balance model indicates that diagenetic iron cycling can only change the isotopic composition of highly reactive iron by water column processes, namely the degree of oxidation of the ferrous seawater iron reservoir, control the isotopic composition of highly reactive iron. Considering a long-term decrease in the isotopic composition of the iron source to the dissolved seawater Fe(II) reservoir to be unlikely, we offer two possible explanations for the Neoproterozoic δ 56Fe trend. First, a decreasing supply of Fe

  19. Low-temperature gas from marine shales

    Science.gov (United States)

    2009-01-01

    Thermal cracking of kerogens and bitumens is widely accepted as the major source of natural gas (thermal gas). Decomposition is believed to occur at high temperatures, between 100 and 200°C in the subsurface and generally above 300°C in the laboratory. Although there are examples of gas deposits possibly generated at lower temperatures, and reports of gas generation over long periods of time at 100°C, robust gas generation below 100°C under ordinary laboratory conditions is unprecedented. Here we report gas generation under anoxic helium flow at temperatures 300° below thermal cracking temperatures. Gas is generated discontinuously, in distinct aperiodic episodes of near equal intensity. In one three-hour episode at 50°C, six percent of the hydrocarbons (kerogen & bitumen) in a Mississippian marine shale decomposed to gas (C1–C5). The same shale generated 72% less gas with helium flow containing 10 ppm O2 and the two gases were compositionally distinct. In sequential isothermal heating cycles (~1 hour), nearly five times more gas was generated at 50°C (57.4 μg C1–C5/g rock) than at 350°C by thermal cracking (12 μg C1–C5/g rock). The position that natural gas forms only at high temperatures over geologic time is based largely on pyrolysis experiments under oxic conditions and temperatures where low-temperature gas generation could be suppressed. Our results indicate two paths to gas, a high-temperature thermal path, and a low-temperature catalytic path proceeding 300° below the thermal path. It redefines the time-temperature dimensions of gas habitats and opens the possibility of gas generation at subsurface temperatures previously thought impossible. PMID:19236698

  20. Low-temperature gas from marine shales

    Directory of Open Access Journals (Sweden)

    Jarvie Daniel M

    2009-02-01

    Full Text Available Abstract Thermal cracking of kerogens and bitumens is widely accepted as the major source of natural gas (thermal gas. Decomposition is believed to occur at high temperatures, between 100 and 200°C in the subsurface and generally above 300°C in the laboratory. Although there are examples of gas deposits possibly generated at lower temperatures, and reports of gas generation over long periods of time at 100°C, robust gas generation below 100°C under ordinary laboratory conditions is unprecedented. Here we report gas generation under anoxic helium flow at temperatures 300° below thermal cracking temperatures. Gas is generated discontinuously, in distinct aperiodic episodes of near equal intensity. In one three-hour episode at 50°C, six percent of the hydrocarbons (kerogen & bitumen in a Mississippian marine shale decomposed to gas (C1–C5. The same shale generated 72% less gas with helium flow containing 10 ppm O2 and the two gases were compositionally distinct. In sequential isothermal heating cycles (~1 hour, nearly five times more gas was generated at 50°C (57.4 μg C1–C5/g rock than at 350°C by thermal cracking (12 μg C1–C5/g rock. The position that natural gas forms only at high temperatures over geologic time is based largely on pyrolysis experiments under oxic conditions and temperatures where low-temperature gas generation could be suppressed. Our results indicate two paths to gas, a high-temperature thermal path, and a low-temperature catalytic path proceeding 300° below the thermal path. It redefines the time-temperature dimensions of gas habitats and opens the possibility of gas generation at subsurface temperatures previously thought impossible.

  1. Sweet spot identification and smart development -An integrated reservoir characterization study of a posidonia shale of a posidonia shale outcrop analogue

    NARCIS (Netherlands)

    Veen, J.H. ten; Verreussel, R.M.C.H.; Ventra, D.; Zijp, M.H.A.A.

    2014-01-01

    Shale gas reservoir stimulation procedures (e.g. hydraulic fracturing) require upfront prediction and planning that should be supported by a comprehensive reservoir characterization. Therefore, understanding shale depositional processes and associated vertical and lateral sedimentological

  2. Sweet spot identification in underexplored shales using multidisciplinary reservoir characterization and key performance indicators : Example of the Posidonia Shale Formation in the Netherlands

    NARCIS (Netherlands)

    Ter Heege, Jan; Zijp, Mart; Nelskamp, Susanne; Douma, Lisanne; Verreussel, Roel; Ten Veen, Johan; de Bruin, Geert; Peters, Rene

    2015-01-01

    Sweet spot identification in underexplored shale gas basins needs to be based on a limited amount of data on shale properties in combination with upfront geological characterization and modelling, because actual production data is usually absent. Multidisciplinary reservoir characterization and

  3. Sweet spot identification in underexplored shales using multidisciplinary reservoir characterization and key performance indicators: example of the Posidonia Shale Formation in the Netherlands

    NARCIS (Netherlands)

    Heege, J.H. ter; Zijp, M.H.A.A.; Nelskamp, S.; Douma, L.A.N.R.; Verreussel, R.M.C.H.; Veen, J.H. ten; Bruin, G. de; Peters, M.C.A.M.

    2015-01-01

    Sweet spot identification in underexplored shale gas basins needs to be based on a limited amount of data on shale properties in combination with upfront geological characterization and modelling, because actual production data is usually absent. Multidisciplinary reservoir characterization and

  4. IN-SITU TRITIUM BETA DETECTOR

    Energy Technology Data Exchange (ETDEWEB)

    J.W. Berthold; L.A. Jeffers

    1998-04-15

    The objectives of this three-phase project were to design, develop, and demonstrate a monitoring system capable of detecting and quantifying tritium in situ in ground and surface waters, and in water from effluent lines prior to discharge into public waterways. The tritium detection system design is based on measurement of the low energy beta radiation from the radioactive decay of tritium using a special form of scintillating optical fiber directly in contact with the water to be measured. The system consists of the immersible sensor module containing the optical fiber, and an electronics package, connected by an umbilical cable. The system can be permanently installed for routine water monitoring in wells or process or effluent lines, or can be moved from one location to another for survey use. The electronics will read out tritium activity directly in units of pico Curies per liter, with straightforward calibration. In Phase 1 of the project, we characterized the sensitivity of fluor-doped plastic optical fiber to tritium beta radiation. In addition, we characterized the performance of photomultiplier tubes needed for the system. In parallel with this work, we defined the functional requirements, target specifications, and system configuration for an in situ tritium beta detector that would use the fluor-doped fibers as primary sensors of tritium concentration in water. The major conclusions from the characterization work are: A polystyrene optical fiber with fluor dopant concentration of 2% gave best performance. This fiber had the highest dopant concentration of any fibers tested. Stability may be a problem. The fibers exposed to a 22-day soak in 120 F water experienced a 10x reduction in sensitivity. It is not known whether this was due to the build up of a deposit (a potentially reversible effect) or an irreversible process such as leaching of the scintillating dye. Based on the results achieved, it is premature to initiate Phase 2 and commit to a prototype

  5. Shale Gas characteristics of Permian black shales (Ecca group, Eastern Cape, South Africa)

    Science.gov (United States)

    Geel, Claire; Booth, Peter; Schulz, Hans-Martin; Horsfield, Brian; de Wit, Maarten

    2013-04-01

    This study involves a comprehensive and detailed lithological, sedimentalogical, structural and geochemical description of the lower Ecca Group in the Eastern Cape, South Africa. The Ecca group hosts a ~ 245 million year old organic-rich black shale, which has recently been the focus of interest of petroleum companies worldwide. The shale was deposited under anoxic conditions in a setting which formed as a consequence of retro-arc foreland basin development related to the Cape Fold Belt. This sedimentary/tectonic environment provided the conditions for deeply buried black shales to reach maturity levels for development in the gas window. The investigation site is called the Greystone Area and is situated north of Wolwefontein en route to Jansenville. The area has outcrops of the Dwyka, the Ecca and the lower Beaufort Groups. The outcrops were mapped extensively and the data was used in conjunction with GIS software to produce a detailed geological map. North-south cross sections were drawn to give indication of bed thicknesses and formation depths. Using the field work, data two boreholes were accurately sited on the northern limb of a shallow easterly plunging syncline. The first borehole reached 100m and the second was drilled to 292m depth (100m percussion and 192m core). The second borehole was drilled 200m south of the first, to penetrate the formations at a greater depth and to avoid surface weathering. Fresh core from the upper Dwyka Group, the Prince Albert Formation, the Whitehill Formation, Collingham Formation and part of the Ripon Formation were successfully extracted and a detailed stratigraphic log has been drawn up. The core was sampled during extraction and the samples were immediately sent to the GFZ in Potsdam, Germany, for geochemical analyses. As suspected the black shales of the the Whitehill Formation are high in organic carbon and have an average TOC value of 4.5%, whereas the Prince Albert and Collingham Formation are below 1%. Tmax values

  6. Vanadium Extraction from Shale via Sulfuric Acid Baking and Leaching

    Science.gov (United States)

    Shi, Qihua; Zhang, Yimin; Liu, Tao; Huang, Jing

    2018-01-01

    Fluorides are widely used to improve vanadium extraction from shale in China. Sulfuric acid baking-leaching (SABL) was investigated as a means of recovering vanadium which does not require the use of fluorides and avoids the productions of harmful fluoride-containing wastewater. Various effective factors were systematically studied and the experimental results showed that 90.1% vanadium could be leached from the shale. On the basis of phase transformations and structural changes after baking the shale, a mechanism of vanadium extraction from shale via SABL was proposed. The mechanism can be described as: (1) sulfuric acid diffusion into particles; (2) the formation of concentrated sulfuric acid media in the particles after water evaporation; (3) hydroxyl groups in the muscovite were removed and transient state [SO4 2-] was generated; and (4) the metals in the muscovite were sulfated by active [SO4 2-] and the vanadium was released. Thermodynamics modeling confirmed this mechanism.

  7. Permeability prediction in shale gas reservoirs using Neural Network

    Science.gov (United States)

    Aliouane, Leila; Ouadfeul, Sid-Ali

    2017-04-01

    Here, we suggest the use of the artificial neural network for permeability prediction in shale gas reservoirs using artificial neural network. Prediction of Permeability in shale gas reservoirs is a complicated task that requires new models where Darcy's fluid flow model is not suitable. Proposed idea is based on the training of neural network machine using the set of well-logs data as an input and the measured permeability as an output. In this case the Multilayer Perceptron neural network machines is used with Levenberg Marquardt algorithm. Application to two horizontal wells drilled in the Barnett shale formation exhibit the power of neural network model to resolve such as problem. Keywords: Artificial neural network, permeability, prediction , shale gas.

  8. Petroleum potential of campano-maastrichtian shales of Anambra ...

    African Journals Online (AJOL)

    lithologies) of campano – Maastrichtian age has been recorded in the Anambra basin. These shale/siltstones lithologies have been reported to be rich in organic matter and had fulfilled other relevant condition for hydrocarbon source rock potential.

  9. Well Planning and Construction Haynesville Shale - East Texas

    Science.gov (United States)

    This paper will focus on the well planning and construction techniques Devon uses in the Haynesville Shale. It will briefly cover issues that are related to designing and drilling the well safely and protecting subsurface drinking water sources.

  10. Environmental baselines: preparing for shale gas in the UK

    Science.gov (United States)

    Bloomfield, John; Manamsa, Katya; Bell, Rachel; Darling, George; Dochartaigh, Brighid O.; Stuart, Marianne; Ward, Rob

    2014-05-01

    Groundwater is a vital source of freshwater in the UK. It provides almost 30% of public water supply on average, but locally, for example in south-east England, it is constitutes nearly 90% of public supply. In addition to public supply, groundwater has a number of other uses including agriculture, industry, and food and drink production. It is also vital for maintaining river flows especially during dry periods and so is essential for maintaining ecosystem health. Recently, there have been concerns expressed about the potential impacts of shale gas development on groundwater. The UK has abundant shales and clays which are currently the focus of considerable interest and there is active research into their characterisation, resource evaluation and exploitation risks. The British Geological Survey (BGS) is undertaking research to provide information to address some of the environmental concerns related to the potential impacts of shale gas development on groundwater resources and quality. The aim of much of this initial work is to establish environmental baselines, such as a baseline survey of methane occurrence in groundwater (National methane baseline study) and the spatial relationships between potential sources and groundwater receptors (iHydrogeology project), prior to any shale gas exploration and development. The poster describes these two baseline studies and presents preliminary findings. BGS are currently undertaking a national survey of baseline methane concentrations in groundwater across the UK. This work will enable any potential future changes in methane in groundwater associated with shale gas development to be assessed. Measurements of methane in potable water from the Cretaceous, Jurassic and Triassic carbonate and sandstone aquifers are variable and reveal methane concentrations of up to 500 micrograms per litre, but the mean value is relatively low at values compare with much higher levels of methane in aquicludes and thermal waters, for example

  11. Naphthenic acids in groundwater overlying undeveloped shale gas and tight oil reservoirs.

    Science.gov (United States)

    Ahad, Jason M E; Pakdel, Hooshang; Lavoie, Denis; Lefebvre, René; Peru, Kerry M; Headley, John V

    2017-10-13

    The acid extractable organics (AEOs) containing naphthenic acids (NAs) in groundwater overlying undeveloped shale gas (Saint-Édouard region) and tight oil (Haldimand sector, Gaspé) reservoirs in Québec, Canada, were analysed using high resolution Orbitrap mass spectrometry and thermal conversion/elemental analysis - isotope ratio mass spectrometry. As classically defined by CnH2n+ZO2, the most abundant NAs detected in the majority of groundwater samples were straight-chain (Z = 0) or monounsaturated (Z = -2) C16 and C18 fatty acids. Several groundwater samples from both study areas, however, contained significant proportions of presumably alicyclic bicyclic NAs (i.e., Z = -4) in the C10-C18 range. These compounds may have originated from migrated waters containing a different distribution of NAs, or are the product of in situ microbial alteration of shale organic matter and petroleum. In most groundwater samples, intramolecular carbon isotope values generated by pyrolysis (δ(13)Cpyr) of AEOs were on average around 2-3‰ heavier than those generated by bulk combustion (δ(13)C) of AEOs, providing further support for microbial reworking of subsurface organic carbon. Although concentrations of AEOs were very low (<2.0 mg/L), the detection of potentially toxic bicyclic acids in groundwater overlying unconventional hydrocarbon reservoirs points to a natural background source of organic contaminants prior to any large-scale commercial hydrocarbon development. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  12. Oil shale project: run summary for small retort Run S-11

    Energy Technology Data Exchange (ETDEWEB)

    Sandholtz, W.A.; Ackerman, F.J.; Bierman, A.; Kaehler, M.; Raley, J.; Laswell, B.H.; Tripp, L.J. (eds.)

    1978-06-01

    Results are reported on retort run S-11 conducted to observe the effects of combustion retorting with undiluted air at relatively rapid burn (retorting) rates and to provide a base case for retorting small uniform shale (Anvil Points master batch -2.5 +- 1.3 cm) with undiluted air. It was found that a 0.6 m/sup 3//m/sup 2//minute superficial gas velocity gave an average rate of propagation of the combustion peak of about 2.7 m/day and an average maximum temperature on the centerline of the rubble bed of 1003/sup 0/C. Oil yield was 93 percent of Fischer assay. For small uniform shale particles (-2.5 + 1.3 cm) it is concluded that only small losses in yield (92 percent vs 96 percent in Run S-10) result from high retorting rates. Maximum temperature considerations preclude going to higher rates with undiluted air. Without diluent, a larger air flux would give excessive bed temperatures causing rock melting and potential closure to gas flow. In experimental retorts, another problem of excessive temperatures is potential damage to metal walls and in-situ sensors. No advantage is seen to using recycled off-gas as a combustion gas diluent. Inert diluents (e.g. nitrogen or steam) may be necessary for process control, but the fuel values in the off-gas should best be used for energy recovery rather than burned in the retort during recycle. Another consideration from model calculations is that the use of recycle gas containing fuel components retards the retorting rate and so is undesirable. No further recycle experiments are planned as the results of this run proved satisfactory.

  13. Trace elements in oil shale. Progress report, 1976--1979

    Energy Technology Data Exchange (ETDEWEB)

    Chappell, W.R.

    1979-01-01

    The overall objective of the program is to evaluate the environmental and health consequences of the release of toxic trace elements (As, B, F, Mo, Se) by shale oil production and use. Some of the particularly significant results are: The baseline geochemical survey shows that stable trace elements maps can be constructed for numerous elements and that the trends observed are related to geologic and climatic factors. Shale retorted by above-ground processes tends to be very homogeneous (both in space and in time) in trace element content. This implies that the number of analytical determinations required of processed shales is not large. Leachate studies show that significant amounts of B, F, And Mo are released from retorted shales and while B and Mo are rapidly flushed out, F is not. On the other hand, As, Se, and most other trace elements ae not present in significant quantities. Significant amounts of F and B are also found in leachates of raw shales. Very large concentrations of reduced sulfur species are found in leachates of processed shale. Upon oxidation a drastic lowering in pH is observed. Preliminary data indicates that this oxidation is catalyzed by bacteria. Very high levels of B and Mo are taken up in some plants growing on processed shale with and without soil cover. These amounts depend upon the process and various site specific characteristics. In general, the amounts taken up decrease with increasing soil cover. On the other hand, we have not observed significant uptake of As, Se, and F into plants. There is a tendency for some trace elements to associate with specific organic fractions, indicating that organic chelation or complexation may play an important role. In particular, most of the Cd, Se, and Cr in shale oil is associated with the organic fraction containing most of the nitrogen-containing compounds.

  14. Rehabilitation potential and practices of Colorado oil shale lands

    Energy Technology Data Exchange (ETDEWEB)

    Sims, P.L.; Redente, E.F.

    1977-01-01

    Considering the problems associated with rehabilitating oil shale disturbed lands in Colorado, a research grant was awarded to Colorado State University by US ERDA. The goal of this research program is to define the rehabilitation potential and practices of Colorado Oil Shale lands. Rehabilitation guidelines are presently being formulated through the study of long-term fertility requirements, soil microorganism dynamics and activity, rate and direction of secondary plant succession, and selection and improvement of plant materials.

  15. Blind Politics of Ambition: Shale Gas in Poland

    OpenAIRE

    Niemuth, Stephanie; Westphal, Sophie

    2014-01-01

    Ever since the impacts of the shale gas revolution in the US have unfolded their measurable effects – as significantly declining natural gas prices – impressive euphoria among those states which are identified to bear high potentials of unconventional gas is widely spread. As for Poland, essentially linked to the hope of profitably producing shale gas is the political will to strive for independence from Russian energy supply and thus, enhance energy supply security. Hence, liberalizing its g...

  16. United States Air Force Shale Oil to Fuels. Phase II.

    Science.gov (United States)

    1981-11-01

    There is no attempt to recover propane , and the light end hydrocarbons are taken to the fuel gas system for feed to the hydrogen plant. Part of the...shale oil charged from the high pressure hydro- treater separator. The hydrotreated shale oil charge stock is combined with the recycle hydrogen rich gas...sulfide and ammonia are steam stripped from the water. The clean water is returned to the refinery and the gas is sent to the amine treater for

  17. Cyclone oil shale retorting concept. [Use it all retorting process

    Energy Technology Data Exchange (ETDEWEB)

    Harak, A.E.; Little, W.E.; Faulders, C.R.

    1984-04-01

    A new concept for above-ground retorting of oil shale was disclosed by A.E. Harak in US Patent No. 4,340,463, dated July 20, 1982, and assigned to the US Department of Energy. This patent titled System for Utilizing Oil Shale Fines, describes a process wherein oil shale fines of one-half inch diameter and less are pyrolyzed in an entrained-flow reactor using hot gas from a cyclone combustor. Spent shale and supplemental fuel are burned at slagging conditions in this combustor. Because of fines utilization, the designation Use It All Retorting Process (UIARP) has been adopted. A preliminary process engineering design of the UIARP, analytical tests on six samples of raw oil shale, and a preliminary technical and economic evaluation of the process were performed. The results of these investigations are summarized in this report. The patent description is included. It was concluded that such changes as deleting air preheating in the slag quench and replacing the condenser with a quench-oil scrubber are recognized as being essential. The addition of an entrained flow raw shale preheater ahead of the cyclone retort is probably required, but final acceptance is felt to be contingent on some verification that adequate reaction time cannot be obtained with only the cyclone, or possibly some other twin-cyclone configuration. Sufficient raw shale preheating could probably be done more simply in another manner, perhaps in a screw conveyor shale transporting system. Results of the technical and economic evaluations of Jacobs Engineering indicate that further investigation of the UIARP is definitely worthwhile. The projected capital and operating costs are competitive with costs of other processes as long as electric power generation and sales are part of the processing facility.

  18. Microbial Deterioration of Marine Diesel Fuel from Oil Shale.

    Science.gov (United States)

    1981-04-09

    eesar mnd Identify by block rumlber) Microbial deterioration DFM Cladosporium resinae Oil shale Synthetic fuel *QNjd&Sp. ACoal Fungi Seawater Petroleum...well in the synthetic fuel as in fuel derived from petroleum. Growth of certain strains of the fungus, Cladosporium resinae , was initially... resina ., and a yeast (Candida sp.) but no inhibition was noted with another shale oil fuel from which the nitrogen constituents ware almost completely

  19. The Influence Factors Analysis and Characteristics Research of Shale Wettability

    Science.gov (United States)

    Su, Siyuan; jiang, Zhenxue

    2017-04-01

    Shales have become one of the leading unconventional oil and gas resources in the world today. The wettability is an important indicator of the rock that reflects the lipophilic and hydrophilic which not only affect oil and water distribution but also can affect the capillary pressure, relative permeability and irreducible water saturation. We present a study of shale wettability using Nuclear Magnetic Resonance (NMR) to monitor sequential imbibition of brine and oil (Dodecane).A total of eleven shale samples of Jiyang Depression of China were analyzed and compared abundance of organic matter, the movable hydrocarbon content, clay content and carbonate content with different wettability. The results showed that the contents of total organic carbon (TOC) with mixed wetting characteristic of shale samples are greater than just water wetting characteristic of shale samples that shows with the increase of TOC content, porosity can be convert into oil wetting by water wetting and the inorganic pores convert into organic pores. It indicates the presence of organic matter is the root cause of mix wettability with the organics contributing mainly to the oil-wetness of the shale samples. The samples that have oil-wetness are higher than the samples only water wetting on movable hydrocarbon contents and clay contents which shows the organic matters are accompanied with clay in the study area. But the samples that only for water wetting have the higher carbonate contents than the oil-wetness samples which indicate the inorganic pores are mainly formed by carbonate rocks. In summary, the shale reservoirs with mix wettability can be used as shale oil enriched favorable exploration targets.

  20. Sweet spots for hydraulic fracturing oil or gas production in underexplored shales using key performance indicators: Example of the Posidonia Shale formation in the Netherlands

    NARCIS (Netherlands)

    Heege, J.H. ter; Zijp, M.H.A.A.; Nelkamp, S.

    2015-01-01

    While extensive data and experiences are available for hydraulic fracturing and hydrocarbon production from shales in the U.S.A., such a record is lacking in many underexplored shale basins worldwide. As limited data is usually available in these basins, analysis of shale prospectivity and

  1. Microbial iron reduction related to metal speciation in mine waste at the former uranium mine in Ranstad

    Energy Technology Data Exchange (ETDEWEB)

    Nejad, F.T. [Goeteborg Univ. (Sweden). Dept. of General and Marine Microbiology

    1998-02-01

    Mining activities in Ranstad uranium mine started in 1965 and ended in 1969. In 1988 the final restoration was discussed, and it was proposed to water-fill the open pit and cover the waste disposal area using the `dry method`. Today the open pit has become a lake. Also some alum shale was placed on the land surface where it has been weathered by oxygen and water during 30 years. In 1994 it was observed that the color of the lake turned over to brown-red. Further studies showed increasing iron concentration in the lake and around the tailings area. For estimation of microbial iron reduction in the lake, three iron reducing bacteria were isolated from the water-filled open pit. For the enrichment process, water samples were inoculated in an anoxic enrichment medium. The isolates were able to reduce Fe(III) oxyhydroxide by oxidation of lactate as energy source. Growth of these strains was determined by production of a black precipitation of iron sulfide and was confirmed by estimation of total number of cells. Fe(III) reduction was monitored by measuring the accumulation of Fe(II) over time. Comparison of the 16S rRNA gene sequences of strains Tran-l, Tran-2, and Tran-3 with the EMBL data base showed 98.6% identity with Shewanella putrefaciens, 98.7% identity with Shewanella alga and 98.2% identity with Aeromonas salmonicida, respectively. S. putrefaciens strains have been isolated from many different environments, many of which are suboxic or anoxic. In addition to growing aerobically, S. putrefaciens can use Fe(III) as terminal electron acceptor under anaerobic conditions. To distinguish if the Fe(III) and/or organic compounds presence in weathered alum shale can be utilized by iron reducing bacteria isolated from the lake, reduction of Fe(III) coupled to the oxidation of organic compounds in sterile and non-sterile weathered alum shale was studied. The reduction of Fe(III) coupled to growth of bacteria on sterile and non-sterile shale was observed. Furthermore

  2. Mining ergonomics

    Energy Technology Data Exchange (ETDEWEB)

    McPhee, B.

    2007-02-15

    Changes in work practices and a drive for greater productivity have introduced a range of emerging issues in ergonomics in mining. Some of the practices appear to be at odds with the need to improve general occupational health and safety. Longer shift lengths and fatigue, mental overload and underload, intermittent heavy physical work, reduced task variation, sedentary work in fixed postures and whole-body vibration all have risks for health and safety. The increasing age of some of the workforce is of concern. There appears to be a need to recognise these as potential causes of health problems. The article gives a review of these problems are reports on research findings. 36 refs., 3 figs.

  3. In-situ remediation of contaminated sediments : conceivable and feasible?!

    NARCIS (Netherlands)

    Joziasse, J.; Gun, J. van der

    2000-01-01

    In-situ remediation has assumed large proportions in dealing with terrestrial soil pollution. Although implementation of in-situ remediation for contaminated sediments is restricted by the fact that dredging is necessary for nautical or water management reasons, it should not be discarded

  4. Development of an in situ polymeric hydrogel implant of ...

    African Journals Online (AJOL)

    Purpose: To prepare and characterize in situ gel-forming implants of methylprednisolone for the treatment of spinal cord injuries. Methods: In situ hydrogels of methylprednisolone were prepared by dispersing polylactide glycolic acid (PLGA) polymer and methylprednisolone in N-methyl-pyrrolidone solvent, and subsequent ...

  5. Human papillomavirus (HPV) in vulvar dysplasia and carcinoma in situ

    DEFF Research Database (Denmark)

    Junge, Jette; Poulsen, H; Horn, T

    1995-01-01

    Surgical specimens from 62 patients with vulvar dysplasia and carcinoma in situ were morphologically investigated. Lesions were classified according to WHO (mild, moderate, severe dysplasia and carcinoma in situ) and according to Toki et al. (1991) (warty, basaloid, combined warty/basaloid or bas...

  6. Comparison of in situ nutrient disappearance of alternative maize ...

    African Journals Online (AJOL)

    Two maize milling by-products (maize gluten feed; MGF and maize by-product feed; MBPF) were compared with shelled maize (SM) and soyabean meal (SBM) for their in situ nutrient disappearance. In situ experiments were conducted in two rumen fistulated Holstein cows to evaluate dry matter (DM), crude protein (CP), ...

  7. Intrathecal Delivery of Ketorolac Loaded In Situ Gels for Prolonged ...

    African Journals Online (AJOL)

    Original Research Article. Intrathecal Delivery of Ketorolac Loaded In Situ Gels for. Prolonged Analgesic and Anti-Inflammatory Activity in. Vertebral Fracture. Shu-E Cao, Sheng-Yang Chen, Jian-Min ... VF as well as spinal injuries and is usually administered through oral ... injection to the body cavity. In situ gel formation.

  8. CGS and In Situ Measurements in Gävle 1999

    DEFF Research Database (Denmark)

    Aage, Helle Karina; Korsbech, Uffe C C; Bargholz, Kim

    1999-01-01

    Calibration of CGS-equipment.In situ measuremts with HPGe-detector (and dose rate meter)in Gävle Sweden as part of the Nordic exercise RESUME99.......Calibration of CGS-equipment.In situ measuremts with HPGe-detector (and dose rate meter)in Gävle Sweden as part of the Nordic exercise RESUME99....

  9. In situ investigation of catalysts for alcohol synthesis

    DEFF Research Database (Denmark)

    Duchstein, Linus Daniel Leonhard; Sharafutdinov, Irek; Wu, Qiongxiao

    consists of three complimentary in situ techniques: (1) Activity measurements based on a reactor connected to a gas chromatograph (GC), (2) In situ x-ray diffractometer (XRD) measurements based on a reactor cell connected to a mass spectrometer (MS), and (3) environmental TEM (ETEM) that allows...... distribution, measured both macroscopically (XRD) and microscopically (ETEM), with the catalytic activity....

  10. IN SITU AND POST REACTION COBALT-INCORPORATION INTO ...

    African Journals Online (AJOL)

    a

    was incorporated onto APTS-modified ethylene-bridged silica materials by in situ and by incipient wetness addition .... In situ and post reaction cobalt-incorporation into mesoporous organosilica materials. Bull. Chem. .... measurements, the samples were sprinkled on a disk smeared with carbon and then coated with gold.

  11. Influence of a polyclonal antibody preparation on the in situ ...

    African Journals Online (AJOL)

    User

    PAP was observed for any in situ degradability parameters of starch from HMMS or pectin of CiPu. It was concluded that the polyclonal antibody preparation had limited effect on the in situ degradability of the tested energy sources. .... cm; measurement taken by the Penn State Particle Size Separator (Lammers et al., 1996).

  12. paediatric ureteric calculi: in-situ extracorporeal shock wave lithotripsy

    African Journals Online (AJOL)

    Objective To evaluate prospectively the efficacy of in-situ extracorporeal shock wave lithotripsy (ESWL) in the treatment of ureteric calculi in the paediatric age group. Patients and Methods Twenty children (aged 2.2 16 years) with 22 ureteric stones were evaluated and treated with in-situ ESWL using the Dornier S lithotripter ...

  13. In situ rumen degradability characteristics of rice straw, soybean ...

    African Journals Online (AJOL)

    This study was intended to evaluate in situ rumen degradability characteristic of soybean curd residue (SCR) and peppermint compared to rice straw, which are used as a functional feed source for beef cattle for high quality beef production. Two steers were fitted with rumen and duodenum cannulae and in situ degradable ...

  14. Photonic MEMS for NIR in-situ

    Energy Technology Data Exchange (ETDEWEB)

    Bond, T C; Cole, G D; Goddard, L L; Behymer, E

    2007-07-03

    We report on a novel sensing technique combining photonics and microelectromechanical systems (MEMS) for the detection and monitoring of gas emissions for critical environmental, medical, and industrial applications. We discuss how MEMS-tunable vertical-cavity surface-emitting lasers (VCSELs) can be exploited for in-situ detection and NIR spectroscopy of several gases, such as O{sub 2}, N{sub 2}O, CO{sub x}, CH{sub 4}, HF, HCl, etc., with estimated sensitivities between 0.1 and 20 ppm on footprints {approx}10{sup -3} mm{sup 3}. The VCSELs can be electrostatically tuned with a continuous wavelength shift up to 20 nm, allowing for unambiguous NIR signature determination. Selective concentration analysis in heterogeneous gas compositions is enabled, thus paving the way to an integrated optical platform for multiplexed gas identification by bandgap and device engineering. We will discuss here, in particular, our efforts on the development of a 760 nm AlGaAs based tunable VCSEL for O{sub 2} detection.

  15. In Situ Immobilization of Selenium in Sediment

    Energy Technology Data Exchange (ETDEWEB)

    Moore, Robert C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stewart, Thomas Austin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    This project focused on the use of a sorbent, carbonated apatite, to immobilize selenium in the environment. It is know that apatite will sorb selenium and based on the mechanism of sorption it is theorized that carbonated apatite will be more effective that pure apatite. Immobilization of selenium in the environment is through the use of a sorbent in a permeable reactive barrier (PRB). A PRB can be constructed by trenching and backfill with the sorbent or in the case of apatite as the sorbent formed in situ using the apatite forming solution of Moore (2003, 2004). There is very little data on selenium sorption by carbonated apatite in the literature. Therefore, in this work, the basic sorptive properties of carbonated apatite were investigated. Carbonated apatite was synthesized by a precipitation method and characterized. Batch selenium kinetic and equilibrium experiments were performed. The results indicate the carbonated apatite contained 9.4% carbonate and uptake of selenium as selenite was rapid; 5 hours for complete uptake of selenium vs. more than 100 hours for pure hydroxyapatite reported in the literature. Additionally, the carbonated apatite exhibited significantly higher distribution coefficients in equilibrium experiments than pure apatite under similar experimental conditions. The next phase of this work will be to seek additional funds to continue the research with the goal of eventually demonstrating the technology in a field application.

  16. Ductal carcinoma in situ of the breast

    Directory of Open Access Journals (Sweden)

    Jennifer L. Peterson

    2011-12-01

    Full Text Available Ductal carcinoma in situ (DCIS of the breast is a noninvasive form of breast cancer that has increased in incidence over the past several decades secondary to screening mammography. DCIS now represents 20–30% of all newly diagnosed cases of breast cancer. Patients with DCIS typically present with an abnormal mammogram, and diagnosis is most commonly obtained with an imageguided biopsy. Historically, mastectomy was considered the primary curative option for patients with DCIS. However, treatment of DCIS continues to evolve, and now treatment strategies also include breast-conserving therapy, which consists of local excision followed by radiation therapy or local excision alone. Multiple randomized trials have confirmed a decrease in ipsilateral breast tumor recurrence in patients treated with local excision followed by radiation therapy compared with local excision alone. Ongoing clinical trials attempt to identify a subgroup of DCIS patients at low risk for recurrence who may not benefit from radiation therapy. In addition, because the majority of ipsilateral breast tumor recurrences occur near the original primary tumor site, partial breast irradiation is currently under investigation as a treatment option for DCIS patients. Randomized trials have shown tamoxifen can reduce the risk of ipsilateral and contralateral breast tumor recurrences while the role of aromatase inhibitors is the subject of current clinical trials. DCIS represents a complex pathologic entity, and treatment optimization requires a multidisciplinary approach.

  17. In situ vitrification of radioactive underground tanks

    Energy Technology Data Exchange (ETDEWEB)

    Koegler, S.S.; Gibby, R.D.; Thompson, L.E.

    1991-10-01

    In situ vitrification (ISV) is a treatment process with great potential for remediating underground tanks previously used for storing radioactive and hazardous chemical wastes at US Department of Energy (DOE) sites. Tests at several scales have demonstrated the utility of ISV for these tanks. An engineering-scale test vitrified a 30-cm-diameter buried steel and concrete tank that contained simulated tank sludge. Hazardous components of the tank sludge were immobilized, or removed and captured in the off-gas treatment system, and the tank walls were melted or incorporated into the ISV block. A pilot-scale ISV test vitrified a 1-m simulated underground tank than contained a simulated refractory sludge. The ISV process completely vitrified the tank, its contents, and the soil below the tank to a depth of 2.4 m, producing a uniform glass and crystalline monolith with an estimated mass of 30 tons. A large-scale underground tank test is scheduled for early 1991. 5 refs., 4 figs.

  18. Life-cycle analysis of shale gas and natural gas.

    Energy Technology Data Exchange (ETDEWEB)

    Clark, C.E.; Han, J.; Burnham, A.; Dunn, J.B.; Wang, M. (Energy Systems); ( EVS)

    2012-01-27

    The technologies and practices that have enabled the recent boom in shale gas production have also brought attention to the environmental impacts of its use. Using the current state of knowledge of the recovery, processing, and distribution of shale gas and conventional natural gas, we have estimated up-to-date, life-cycle greenhouse gas emissions. In addition, we have developed distribution functions for key parameters in each pathway to examine uncertainty and identify data gaps - such as methane emissions from shale gas well completions and conventional natural gas liquid unloadings - that need to be addressed further. Our base case results show that shale gas life-cycle emissions are 6% lower than those of conventional natural gas. However, the range in values for shale and conventional gas overlap, so there is a statistical uncertainty regarding whether shale gas emissions are indeed lower than conventional gas emissions. This life-cycle analysis provides insight into the critical stages in the natural gas industry where emissions occur and where opportunities exist to reduce the greenhouse gas footprint of natural gas.

  19. Mechanical Properties of Gas Shale During Drilling Operations

    Science.gov (United States)

    Yan, Chuanliang; Deng, Jingen; Cheng, Yuanfang; Li, Menglai; Feng, Yongcun; Li, Xiaorong

    2017-07-01

    The mechanical properties of gas shale significantly affect the designs of drilling, completion, and hydraulic fracturing treatments. In this paper, the microstructure characteristics of gas shale from southern China containing up to 45.1% clay were analyzed using a scanning electron microscope. The gas shale samples feature strongly anisotropic characteristics and well-developed bedding planes. Their strength is controlled by the strength of both the matrix and the bedding planes. Conventional triaxial tests and direct shear tests are further used to study the chemical effects of drilling fluids on the strength of shale matrix and bedding planes, respectively. The results show that the drilling fluid has a much larger impact on the strength of the bedding plane than that of the shale matrix. The impact of water-based mud (WBM) is much larger compared with oil-based mud. Furthermore, the borehole collapse pressure of shale gas wells considering the effects of drilling fluids are analyzed. The results show that the collapse pressure increases gradually with the increase of drilling time, especially for WBM.

  20. Climate impact of potential shale gas production in the EU

    Energy Technology Data Exchange (ETDEWEB)

    Forster, D.; Perks, J. [AEA Technology plc, London (United Kingdom)

    2012-07-15

    Existing estimates of GHG emissions from shale gas production and available abatement options were used to obtain improved estimates of emissions from possible shale gas exploitation in the EU. GHG emissions per unit of electricity generated from shale gas were estimated to be around 4 to 8% higher than for electricity generated by conventional pipeline gas from within Europe. These additional emissions arise in the pre-combustion stage, predominantly in the well completion phase when the fracturing fluid is brought back to the surface together with released methane. If emissions from well completion are mitigated, through flaring or capture, and utilised, then this difference is reduced to 1 to 5%. The analysis suggests that the emissions from shale gas-based power generation (base case) are 2 to 10% lower than those from electricity generated from sources of conventional pipeline gas located outside of Europe (in Russia and Algeria), and 7 to 10% lower than those from electricity generated from LNG imported into Europe. However, under our 'worst case' shale gas scenario, where all flow back gases at well completion are vented, emissions from electricity generated from shale gas would be similar to the upper emissions level for electricity generated from imported LNG and for gas imported from Russia.

  1. Water Availability for Shale Gas Development in Sichuan Basin, China.

    Science.gov (United States)

    Yu, Mengjun; Weinthal, Erika; Patiño-Echeverri, Dalia; Deshusses, Marc A; Zou, Caineng; Ni, Yunyan; Vengosh, Avner

    2016-03-15

    Unconventional shale gas development holds promise for reducing the predominant consumption of coal and increasing the utilization of natural gas in China. While China possesses some of the most abundant technically recoverable shale gas resources in the world, water availability could still be a limiting factor for hydraulic fracturing operations, in addition to geological, infrastructural, and technological barriers. Here, we project the baseline water availability for the next 15 years in Sichuan Basin, one of the most promising shale gas basins in China. Our projection shows that continued water demand for the domestic sector in Sichuan Basin could result in high to extremely high water stress in certain areas. By simulating shale gas development and using information from current water use for hydraulic fracturing in Sichuan Basin (20,000-30,000 m(3) per well), we project that during the next decade water use for shale gas development could reach 20-30 million m(3)/year, when shale gas well development is projected to be most active. While this volume is negligible relative to the projected overall domestic water use of ∼36 billion m(3)/year, we posit that intensification of hydraulic fracturing and water use might compete with other water utilization in local water-stress areas in Sichuan Basin.

  2. Eastern gas shales subprogram. [Appalachia, Illinois and Michigan Basins

    Energy Technology Data Exchange (ETDEWEB)

    1984-02-01

    The goal of the Eastern Gas Shales Subprogram (EGSS) is to develop scientific and engineering knowledge and to enable the recovery of natural gas from shale formations that underlie the Appalachian, Illinois, and Michigan Basins. To pursue this goal, the geology and chemistry of gas-bearing Devonian shales was characterized early during the subprogram. As information was gathered and knowledge of the shales increased, studies of well completion and stimulation methods were conducted in the laboratory as well as in the field. Recently, the synthesis of geologic and geochemical data marked the conclusion of the resource characterization effort. Upon the completion of the resource characterization, project emphasis was directed toward understanding the fractured shale reservoir and its gas storage and production characteristics. The Meigs County, Ohio, offset well test established the directional aspects of shale gas production, providing new insight into field development. In addition, a methodology for characterizing gas flow behavior allows for the development and application of novel extraction methods to increase the otherwise poor recovery efficiency of current extraction methods.

  3. Standardized surface engineering design of shale gas reservoirs

    Directory of Open Access Journals (Sweden)

    Guangchuan Liang

    2016-01-01

    Full Text Available Due to the special physical properties of shale gas reservoirs, it is necessary to adopt unconventional and standardized technologies for its surface engineering construction. In addition, the surface engineering design of shale gas reservoirs in China faces many difficulties, such as high uncertainty of the gathering and transportation scale, poor adaptability of pipe network and station layout, difficult matching of the process equipments, and boosting production at the late stage. In view of these problems, the surface engineering construction of shale gas reservoirs should follow the principles of “standardized design, modularized construction and skid mounted equipment”. In this paper, standardized surface engineering design technologies for shale gas reservoirs were developed with the “standardized well station layout, universal process, modular function zoning, skid mounted equipment selection, intensive site design, digitized production management” as the core, after literature analysis and technology exploration were carried out. Then its application background and surface technology route were discussed with a typical shale gas field in Sichuan–Chongqing area as an example. Its surface gathering system was designed in a standardized way, including standardized process, the modularized gathering and transportation station, serialized dehydration unit and intensive layout, and remarkable effects were achieved. A flexible, practical and reliable ground production system was built, and a series of standardized technology and modularized design were completed, including cluster well platform, set station, supporting projects. In this way, a system applicable to domestic shale gas surface engineering construction is developed.

  4. In situ containment and stabilization of buried waste

    Energy Technology Data Exchange (ETDEWEB)

    Allan, M.L.; Kukacka, L.E.; Heiser, J.H.

    1992-11-01

    The objective of the project was to develop, demonstrate and implement advanced grouting materials for the in-situ installation of impermeable, durable subsurface barriers and caps around waste sites and for the in-situ stabilization of contaminated soils. Specifically, the work was aimed at remediation of the Chemical Waste (CWL) and Mixed Waste Landfills (MWL) at Sandia National Laboratories (SNL) as part of the Mixed Waste Landfill Integrated Demonstration (MWLID). This report documents this project, which was conducted in two subtasks. These were (1) Capping and Barrier Grouts, and (2) In-situ Stabilization of Contaminated Soils. Subtask 1 examined materials and placement methods for in-situ containment of contaminated sites by subsurface barriers and surface caps. In Subtask 2 materials and techniques were evaluated for in-situ chemical stabilization of chromium in soil.

  5. A generic mine model

    NARCIS (Netherlands)

    Veldhoven, J. van; Riet, M.W.G. van; Dol, H.S.; Mohamoud, A.A.; Keus, D.; Beckers, A.L.D.

    2009-01-01

    In the field of mine laying and of mine countermeasures, understanding of the actuation behaviour of influence mines is of vital importance. Modelling can enhance such understanding. In this paper, a flexible generic mine model is presented that allows the user to easily generate different computer

  6. Modeling of fault reactivation and induced seismicity during hydraulic fracturing of shale-gas reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Rutqvist, Jonny; Rinaldi, Antonio P.; Cappa, Frédéric; Moridis, George J.

    2013-07-01

    We have conducted numerical simulation studies to assess the potential for injection-induced fault reactivation and notable seismic events associated with shale-gas hydraulic fracturing operations. The modeling is generally tuned towards conditions usually encountered in the Marcellus shale play in the Northeastern US at an approximate depth of 1500 m (~;;4,500 feet). Our modeling simulations indicate that when faults are present, micro-seismic events are possible, the magnitude of which is somewhat larger than the one associated with micro-seismic events originating from regular hydraulic fracturing because of the larger surface area that is available for rupture. The results of our simulations indicated fault rupture lengths of about 10 to 20 m, which, in rare cases can extend to over 100 m, depending on the fault permeability, the in situ stress field, and the fault strength properties. In addition to a single event rupture length of 10 to 20 m, repeated events and aseismic slip amounted to a total rupture length of 50 m, along with a shear offset displacement of less than 0.01 m. This indicates that the possibility of hydraulically induced fractures at great depth (thousands of meters) causing activation of faults and creation of a new flow path that can reach shallow groundwater resources (or even the surface) is remote. The expected low permeability of faults in producible shale is clearly a limiting factor for the possible rupture length and seismic magnitude. In fact, for a fault that is initially nearly-impermeable, the only possibility of larger fault slip event would be opening by hydraulic fracturing; this would allow pressure to penetrate the matrix along the fault and to reduce the frictional strength over a sufficiently large fault surface patch. However, our simulation results show that if the fault is initially impermeable, hydraulic fracturing along the fault results in numerous small micro-seismic events along with the propagation, effectively

  7. Estimating fracture spacing from natural tracers in shale-gas production

    Science.gov (United States)

    Bauer, S. J.; McKenna, S. A.; Heath, J. E.; Gardner, P.

    2012-12-01

    Resource appraisal and long-term recovery potential of shale gas relies on the characteristics of the fracture networks created within the formation. Both well testing and analysis of micro-seismic data can provide information on fracture characteristics, but approaches that directly utilize observations of gas transport through the fractures are not well-developed. We examine transport of natural tracers and analyze the breakthrough curves (BTC's) of these tracers with a multi-rate mass transfer (MMT) model to elucidate fracture characteristics. The focus here is on numerical simulation studies to determine constraints on the ability to accurately estimate fracture network characteristics as a function of the diffusion coefficients of the natural tracers, the number and timing of observations, the flow rates from the well, and the noise in the observations. Traditional tracer testing approaches for dual-porosity systems analyze the BTC of an injected tracer to obtain fracture spacing considering a single spacing value. An alternative model is the MMT model where diffusive mass transfer occurs simultaneously over a range of matrix block sizes defined by a statistical distribution (e.g., log-normal, gamma, or power-law). The goal of the estimation is defining the parameters of the fracture spacing distribution. The MMT model has not yet been applied to analysis of natural in situ natural tracers. Natural tracers are omnipresent in the subsurface, potentially obviating the needed for introduced tracers, and could be used to improve upon fracture characteristics estimated from pressure transient and decline curve production analysis. Results of this study provide guidance for data collection and analysis of natural tracers in fractured shale formations. Parameter estimation on simulated BTC's will provide guidance on the necessary timing of BTC sampling in field experiments. The MMT model can result in non-unique or nonphysical parameter estimates. We address this

  8. Impacts of Marcellus Shale Natural Gas Production on Regional Air Quality

    Science.gov (United States)

    Swarthout, R.; Russo, R. S.; Zhou, Y.; Mitchell, B.; Miller, B.; Lipsky, E. M.; Sive, B. C.

    2012-12-01

    Natural gas is a clean burning alternative to other fossil fuels, producing lower carbon dioxide (CO2) emissions during combustion. Gas deposits located within shale rock or tight sand formations are difficult to access using conventional drilling techniques. However, horizontal drilling coupled with hydraulic fracturing is now widely used to enhance natural gas extraction. Potential environmental impacts of these practices are currently being assessed because of the rapid expansion of natural gas production in the U.S. Natural gas production has contributed to the deterioration of air quality in several regions, such as in Wyoming and Utah, that were near or downwind of natural gas basins. We conducted a field campaign in southwestern Pennsylvania on 16-18 June 2012 to investigate the impact of gas production operations in the Marcellus Shale on regional air quality. A total of 235 whole air samples were collected in 2-liter electropolished stainless- steel canisters throughout southwestern Pennsylvania in a regular grid pattern that covered an area of approximately 8500 square km. Day and night samples were collected at each grid point and additional samples were collected near active wells, flaring wells, fluid retention reservoirs, transmission pipelines, and a processing plant to assess the influence of different stages of the gas production operation on emissions. The samples were analyzed at Appalachian State University for methane (CH4), CO2, C2-C10 nonmethane hydrocarbons (NMHCs), C1-C2 halocarbons, C1-C5 alkyl nitrates and selected reduced sulfur compounds. In-situ measurements of ozone (O3), CH4, CO2, nitric oxide (NO), total reactive nitrogen (NOy), formaldehyde (HCHO), and a range of volatile organic compounds (VOCs) were carried out at an upwind site and a site near active gas wells using a mobile lab. Emissions associated with gas production were observed throughout the study region. Elevated mixing ratios of CH4 and CO2 were observed in the

  9. Swelling behaviour of Early Jurassic shales when exposed to water vapour

    Science.gov (United States)

    Houben, Maartje; Barnhoorn, Auke; Peach, Colin; Drury, Martyn

    2017-04-01

    The presence of water in mudrocks has a largely negative impact on production of gas, due to the fact that water causes swelling of the rock. Removing the water from the mudrock on the other hand could potentially shrink the rock and increase the matrix permeability. Investigation of the swelling/shrinkage behaviour of the rock during exposure to water vapour is of key importance in designing and optimizing unconventional production strategies. We have used outcrop samples of the Whitby Mudstone and the Posidonia shale [1], potential unconventional sources for gas in North-western Europe, to measure the swelling and shrinkage behaviour. Subsamples, 1 mm cubes, were prepared by the Glass Workshop at Utrecht University using a high precision digitally controlled diamond wafering saw cooled by air. The mm cubes were then exposed to atmospheres with different relative humidities either in an Environmental Scanning Electron Microscope (ESEM) or in a 3D dilatometer. So that the sample responses to exposure of water vapour could be measured. Parallel to the bedding we found a swelling strain between 0.5 and 1.5 %, perpendicular to the bedding though swelling strain varied between 1 and 3.5%. Volumetric swelling strain varied between 1 and 2% at a maximum relative humidity of 95%. Volumetric swelling strains measured in the Early Toarcian Shales are similar to the ones found in coal [2], where the results suggest that it might be possible to increase permeability in the reservoir by decreasing the in-situ water activity due to shrinkage of the matrix. [1] M.E. Houben, A. Barnhoorn, L. Wasch, J. Trabucho-Alexandre, C. J. Peach, M.R. Drury (2016). Microstructures of Early Jurassic (Toarcian) shales of Northern Europe, International Journal of Coal Geology, 165, 76-89. [2] Jinfeng Liu, Colin J. Peach, Christopher J. Spiers (2016). Anisotropic swelling behaviour of coal matrix cubes exposed to water vapour: Effects of relative humidity and sample size, International Journal of

  10. South African mining experience

    Energy Technology Data Exchange (ETDEWEB)

    Buck, J.D. (British Coal Corporation (UK). North Selby Mine)

    1992-09-01

    The article details the author's visit to South Africa on the 1990 Institution of Mining Electrical and Mining Mechanical Engineers Travelling Scholarship. The author undertook to visit to six coal mines (including two opencast mines and one rail loading terminal), four local engineering manufacturers, three power stations, three gold mines, two diamond mines (both in Botswana), a steel and vanadium works, the 1990 Mining Electra exhibition and the head offices of the Anglo American Corporation of South Africa. 4 figs., 2 tabs.

  11. Economic recovery and processing of posidonia shale in the investigation area of Schandelah. Wirtschaftliche Gewinnunug und Verwertung von Posidonienschiefer des Untersuchungsgebietes Schandelah

    Energy Technology Data Exchange (ETDEWEB)

    Kruk, H.U.; Czibulinski, U.; Schulze, R.; Harjung, J.; Frohnert, H.; Orlowski, W.; Drescher, J.; Ebert, L.; Ernst, H.; Schmitz, H.H.

    1983-07-01

    The object of the investigations, which took several years, was to test most up-to-date technologies in the fields of mining and chemical process engineering applied to posidonia shale of the Schandelah deposit type with regard to an economic recovery and processing of this primary energy source in the Braunschweig-Wolfsburg-Koenigslutter area. The results have shown that about two billion tons of oil shale can be exploited and possibly commercially utilized in this area. The importance of these results is given by the fact that in this economic domain a primary energy source with a thermal value of about 8.2 EJ has been detected, which can produce at least 100 million tons of syncrude. If this deposit is to be used for producing electrical energy it can provide about 800 TWh.

  12. Conversion of Coal Mine Gas to LNG

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2016-02-05

    This project evolved from a 1995, DOE-NETL competitive solicitation for practical CMM capture and utilization concepts. Appalachian Pacific was one of three companies selected to proceed with the construction and operation of a cost-shared demonstration plant. In the course of trying to proceed with this demonstration plant, AP examined several liquefaction technologies, discussed obtaining rights to coal mine methane with a number of coal companies, explored marketing potential with a wide variety of customers in many sections of the United States, studied in great detail the impact of a carbon credit exchange, and developed a suite of analytical tools with which to evaluate possible project options. In the end, the newness of the product, reluctance on the part of the coal companies to venture away from time tested practices, difficulty with obtaining financing, the failure of a carbon credit market to develop and the emergence of shale derived gas production prevented a demonstration plant from being built.

  13. Shale gas characterization based on geochemical and geophysical analysis: Case study of Brown shale, Pematang formation, Central Sumatra Basin

    Science.gov (United States)

    Haris, A.; Nastria, N.; Soebandrio, D.; Riyanto, A.

    2017-07-01

    Geochemical and geophysical analyses of shale gas have been carried out in Brown Shale, Middle Pematang Formation, Central Sumatra Basin. The paper is aimed at delineating the sweet spot distribution of potential shale gas reservoir, which is based on Total Organic Carbon (TOC), Maturity level data, and combined with TOC modeling that refers to Passey and Regression Multi Linear method. We used 4 well data, side wall core and 3D pre-stack seismic data. Our analysis of geochemical properties is based on well log and core data and its distribution are constrained by a framework of 3D seismic data, which is transformed into acoustic impedance. Further, the sweet spot of organic-rich shale is delineated by mapping TOC, which is extracted from inverted acoustic impedance. Our experiment analysis shows that organic materials contained in the formation of Middle Pematang Brown Shale members have TOC range from 0.15 to 2.71 wt.%, which is classified in the quality of poor to very good. In addition, the maturity level of organic material is ranging from 373°C to 432°C, which is indicated by vitrinite reflectance (Ro) of 0.58. In term of kerogen type, this Brown shale formation is categorized as kerogen type of II I III, which has the potential to generate a mixture of gasIoil on the environment.

  14. Bayesian inversion of synthetic AVO data to assess fluid and shale content in sand-shale media

    Science.gov (United States)

    Anwer, Hafiz Mubbasher; Ali, Aamir; Alves, Tiago M.

    2017-04-01

    Reservoir characterization of sand-shale sequences has always challenged geoscientists due to the presence of anisotropy in the form of shale lenses or shale layers. Water saturation and volume of shale are among the fundamental reservoir properties of interest for sand-shale intervals, and relate to the amount of fluid content and accumulating potentials of such media. This paper suggests an integrated workflow using synthetic data for the characterization of shaley-sand media based on anisotropic rock physics (T-matrix approximation) and seismic reflectivity modelling. A Bayesian inversion scheme for estimating reservoir parameters from amplitude vs. offset (AVO) data was used to obtain the information about uncertainties as well as their most likely values. The results from our workflow give reliable estimates of water saturation from AVO data at small uncertainties, provided background sand porosity values and isotropic overburden properties are known. For volume of shale, the proposed workflow provides reasonable estimates even when larger uncertainties are present in AVO data.

  15. Slow Radio-Frequency Processing of Large Oil Shale Volumes to Produce Petroleum-Like Shale Oil

    Energy Technology Data Exchange (ETDEWEB)

    Burnham, A K

    2003-08-20

    A process is proposed to convert oil shale by radio frequency heating over a period of months to years to create a product similar to natural petroleum. Electrodes would be placed in drill holes, either vertical or horizontal, and a radio frequency chosen so that the penetration depth of the radio waves is of the order of tens to hundreds of meters. A combination of excess volume production and overburden compaction drives the oil and gas from the shale into the drill holes, where it is pumped to the surface. Electrical energy for the process could be provided initially by excess regional capacity, especially off-peak power, which would generate {approx}3 x 10{sup 5} bbl/day of synthetic crude oil, depending on shale grade. The electricity cost, using conservative efficiency assumptions, is $4.70 to $6.30/bbl, depending on grade and heating rate. At steady state, co-produced gas can generate more than half the electric power needed for the process, with the fraction depending on oil shale grade. This would increase production to 7.3 x 10{sup 5} bbl/day for 104 l/Mg shale and 1.6 x 10{sup 6} bbl/day for 146 l/Mg shale using a combination of off-peak power and power from co-produced gas.

  16. Western oil shale development: a technology assessment. Volume 8. Health effects of oil shale development

    Energy Technology Data Exchange (ETDEWEB)

    Rotariu, G.J.

    1982-02-01

    Information on the potential health effects of a developing oil shale industry can be derived from two major sources: (1) the historical experience in foreign countries that have had major industries; and (2) the health effects research that has been conducted in the US in recent years. The information presented here is divided into two major sections: one dealing with the experience in foreign countries and the second dealing with the more recent work associated with current oil shale development in the US. As a result of the study, several observations can be made: (1) most of the current and historical data from foreign countries relate to occupational hazards rather than to impacts on regional populations; (2) neither the historical evidence from other countries nor the results of current research have shown pulmonary neoplasia to be a major concern, however, certain types of exposure, particularly such mixed source exposures as dust/diesel or dust/organic-vapor have not been adequately studied and the lung cancer question is not closed; (3) the industry should be alert to the incidence of skin disease in the industrial setting, however, automated techniques, modern industrial hygiene practices and realistic personal hygiene should greatly reduce the hazards associated with skin contact; and (4) the entire question of regional water contamination and any resultant health hazard has not been adequately addressed. The industrial practice of hydrotreating the crude shale oil will diminish the carcinogenic hazard of the product, however, the quantitative reduction of biological activity is dependent on the degree of hydrotreatment. Both Soviet and American experimentalists have demonstrated a correlation betweed carcinogenicity/toxicity and retorting temperature; the higher temperatures producing the more carcinogenic or toxic products.

  17. Remediation strategies for historical mining and smelting sites.

    Science.gov (United States)

    Dybowska, Agnieszka; Farago, Margaret; Valsami-Jones, Eugenia; Thornton, Iain

    2006-01-01

    The environmental, social and economic problems associated with abandoned mine sites are serious and global. Environmental damage arising from polluted waters and dispersal of contaminated waste is a feature characteristic of many old mines in North America, Australia, Europe and elsewhere. Today, because of the efficiency of mining operations and legal requirements in many countries for prevention of environmental damage from mining operations, the release of metals to the environment from modern mining is low. However, many mineralized areas that were extensively worked in the 18th and 19th centuries and left abandoned after mining had ceased, have left a legacy of metal contaminated land. Unlike organic chemicals and plastics, metals cannot be degraded chemically or biologically into non-toxic and environmentally neutral constituents. Thus sites contaminated with toxic metals present a particular challenge for remediation. Soil remediation has been the subject of a significant amount of research work in the past decade; this has resulted in a number of remediation options currently available or being developed. Remediation strategies for metal/metalloid contaminated historical mining sites are reviewed and summarized in this article. It focuses on the current applications of in situ remediation with the use of soil amendments (adsorption and precipitation based methods are discussed) and phytoremediation (in situ plant based technology for environmental clean up and restoration). These are promising alternative technologies to traditional options of excavation and ex situ treatment, offering an advantage of being non-invasive and low cost. In particular, they have been shown to be effective in remediation of mining and smelting contaminated sites, although the long-term durability of these treatments cannot be predicted.

  18. in situ Calcite Precipitation for Contaminant Immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Yoshiko Fujita; Robert W. Smith

    2009-08-01

    in situ Calcite Precipitation for Contaminant Immobilization Yoshiko Fujita (Yoshiko.fujita@inl.gov) (Idaho National Laboratory, Idaho Falls, Idaho, USA) Robert W. Smith (University of Idaho-Idaho Falls, Idaho Falls, Idaho, USA) Subsurface radionuclide and trace metal contaminants throughout the U.S. Department of Energy (DOE) complex pose one of DOE’s greatest challenges for long-term stewardship. One promising stabilization mechanism for divalent trace ions, such as the short-lived radionuclide strontium-90, is co-precipitation in calcite. Calcite, a common mineral in the arid western U.S., can form solid solutions with trace metals. The rate of trace metal incorporation is susceptible to manipulation using either abiotic or biotic means. We have previously demonstrated that increasing the calcite precipitation rate by stimulating the activity of urea hydrolyzing microorganisms can result in significantly enhanced Sr uptake. Urea hydrolysis causes the acceleration of calcium carbonate precipitation (and trace metal co-precipitation) by increasing pH and alkalinity, and also by liberating the reactive cations from the aquifer matrix via exchange reactions involving the ammonium ion derived from urea: H2NCONH2 + 3H2O ? 2NH4+ + HCO3- + OH- urea hydrolysis >X:2Ca + 2NH4+ ? 2>X:NH4 + Ca2+ ion exchange Ca2+ + HCO3- + OH- ? CaCO3(s) + H2O calcite precipitation where >X: is a cation exchange site on the aquifer matrix. This contaminant immobilization approach has several attractive features. Urea hydrolysis is catalyzed by the urease enzyme, which is produced by many indigenous subsurface microorganisms. Addition of foreign microbes is unnecessary. In turn the involvement of the native microbes and the consequent in situ generation of reactive components in the aqueous phase (e.g., carbonate and Ca or Sr) can allow dissemination of the reaction over a larger volume and/or farther away from an amendment injection point, as compared to direct addition of the reactants at

  19. Ductal carcinoma in situ: a challenging disease

    Directory of Open Access Journals (Sweden)

    Sevilay Altintas

    2011-12-01

    Full Text Available Ductal carcinoma in situ (DCIS represents a heterogenous group of lesions with variable malignant potential. Although it is clearly pre-invasive, not all lesions progress to an invasive malignant disease. The significant increase in the frequency of diagnosis is the result of both widespread use of screening mammography and better recognition among pathologists. Treatment is controversial, but for several decades total mastectomy has been considered as the appropriate treatment. The tendency to be less aggressive in terms of surgery has followed the pattern of events observed in the treatment of invasive breast carcinomas. More recently, it has become clear that breastconserving procedures could be applied and selected on the basis of diagnostics and risk factors. When all patients with DCIS are considered, the overall mortality is extremely low, only about 1–2%. On the other hand, breast-conserving surgery is only curative in 75–85%; 50% of the local recurrences have proven to be invasive with a mortality rate of 12–15%. There is no place for axillary node dissection, adjuvant hormonal treatment or chemotherapy in the treatment. Important factors in predicting local recurrence are age, family history, nuclear grade, comedo-type necrosis, tumor size and margin width. With the addition of radiation therapy to excisional surgery, there is a 50% reduction in the overall local recurrence rate. The Van Nuys Prognostic Index (VNPI, recently updated, is a tool that quantifies measurable prognostic factors that can be used in the decision-making process of treatment. Recent data from large cohort studies and randomized trials have emerged to guide treatment. DCIS is now understood to have diverse malignant potential and it is unlikely that there will be a single treatment for this wide range of lesions. Advances in molecular biology and gene expression profiling of human breast tumors have been providing important insights into the relationship

  20. Microbial Repopulation Following In Situ STAR Remediation

    Science.gov (United States)

    Gerhard, J.; Overbeeke, G.; Edwards, E.; Lomheim, L.; Grant, G.

    2016-12-01

    STAR (Self-sustaining Treatment for Active Remediation) is an emerging remediation technology that employs a self-sustaining smouldering reaction to destroy nonaqueous phase liquids (NAPLs) in the subsurface. The reaction front travels outwards from an ignition well at approximately 0.5 per day and subjects the soil to temperatures of 400°C-1000°C. The objectives of this work were to monitor re-saturation of the soil over time and quantify the microbial repopulation of the treated zone. STAR is currently being applied as a full scale, in situ remedy for coal tar beneath a former creosol manufacturing facility in New Jersey, USA. This study analyzed soil cores taken at regular intervals following STAR treatment, allowing time for groundwater to re-infiltrate and for microbial populations to potentially reestablish. Soil and groundwater were analyzed for total number of microorganisms via quantitative Polymerase Chain Reaction (qPCR), as well as microbial diversity via amplicon sequencing. Results demonstrate that microbes rapidly repopulated over a 2 month period to 106 gene copies/g of soil. However, concentrations in the treated zone did not rise above this concentration over 6 months post-STAR, indicating a low carrying capacity of the treated soil. To examine the system in more detail and consider the effects of bio-stimulation, a bench top column study using site soil and artificial groundwater explored the rate at which STAR-treated soil is repopulated with naturally occurring microorganisms in the presence and absence of lactate and a terminal electron acceptor. Results demonstrated that biostimulation did not increase the carrying capacity of the STAR treated sol, but rather shifted the microbial community to reflect the TEA provided, in this case, promoting sulfate reducers. Overall, the work illustrates that microbial populations in STAR treated soil do recover via groundwater infiltration but robust communities will take time to naturally establish.

  1. IN SITU MEASUREMENT OF BEDROCK EROSION

    Directory of Open Access Journals (Sweden)

    D. H. Rieke-Zapp

    2012-07-01

    Full Text Available While long term erosion rates of bedrock material may be estimated by dating methods, current day erosion rates are – if at all available – based on rough estimates or on point measurements. Precise quantification of short term erosion rates are required to improve our understanding of short term processes, for input in landscape evolution models, as well as for studying the mechanics and efficiency of different erosion processes in varying geomorphological settings. Typical current day erosion rates in the European Alps range from sub-millimetre to several millimetres per year depending on the dominant erosion processes. The level of surveying accuracy required for recurring sub-millimetre to millimetre measurements in the field is demanding. A novel surveying setup for in-situ measurement of bedrock erosion was tested recently in three different locations in Switzerland. Natural bedrock was investigated in the Gornera gorge close to Zermatt. Further on, bedrock samples were installed in exposed locations in the Erlenbach research watershed close to Einsiedeln, and in the Illgraben debris flow channel, located in the Canton Schwyz and Valais, respectively. A twofold measurement approach was chosen for all locations. For the first setup control points providing an absolute reference frame for recurrent measurements were embedded close to the area of interest. Close range photogrammetry was applied to measure surface changes on the bedrock samples. The precision for surface measurements in the field was 0.1 mm (1 σ and thus suitable for the application. The equipment needed for the surveys can easily be carried to the field. At one field site a structured light scanner was used along with the photogrammetric setup. Although the current generation of structured light scanners appeared less suitable for field application, data acquisition was much faster and checking the data for completeness in the field was straight forward. The latest

  2. Oil shale, tar sand, coal research advanced exploratory process technology, jointly sponsored research. Quarterly technical progress report, October--December 1992

    Energy Technology Data Exchange (ETDEWEB)

    Speight, J.G.

    1992-12-31

    Accomplishments for the past quarter are presented for the following five tasks: oil shale; tar sand; coal; advanced exploratory process technology; and jointly sponsored research. Oil shale research covers oil shale process studies. Tar sand research is on process development of Recycle Oil Pyrolysis and Extraction (ROPE) Process. Coal research covers: coal combustion; integrated coal processing concepts; and solid waste management. Advanced exploratory process technology includes: advanced process concepts;advanced mitigation concepts; and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; CROW field demonstration with Bell Lumber and Pole; development and validation of a standard test method for sequential batch extraction fluid; PGI demonstration project; operation and evaluation of the CO{sub 2} HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesaverde Group, Greater Green River Basin, tight gas sands; flow-loop testing of double-wall pipe for thermal applications; characterization of petroleum residue; shallow oil production using horizontal wells with enhanced oil recovery techniques; surface process study for oil recovery using a thermal extraction process; NMR analysis of samples from the ocean drilling program; in situ treatment of manufactured gas plant contaminated soils demonstration program; and solid state NMR analysis of naturally and artificially matured kerogens.

  3. Pressurized fluidized-bed hydroretorting of Eastern oil shales

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, M.J.; Mensinger, M.C.; Rue, D.M.; Lau, F.S. (Institute of Gas Technology, Chicago, IL (United States)); Schultz, C.W. (Alabama Univ., University, AL (United States)); Parekh, B.K. (Kentucky Univ., Lexington, KY (United States)); Misra, M. (Nevada Univ., Reno, NV (United States)); Bonner, W.P. (Tennessee Technological Univ., Cookeville, TN (United States))

    1992-11-01

    The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process specifically for application to beneficiated shale as feedstock. Studies have shown that beneficiated shale is the preferred feedstock for pressurized hydroretorting. The program extension is divided into the following active tasks. Task 3. testing of process improvement concepts; Task 4. beneficiation research; Task 5. operation of PFH on beneficiated shale; Task 6. environmental data and mitigation analyses; Task 7. sample procurement, preparation, and characterization; and Task 8. project management and reporting. In order to accomplish all the program objectives, the Institute of Gas Technology (IGT), the prime contractor, worked with four other institutions: the University of Alabama/Mineral Resources Institute (MRI), the University of Kentucky Center for Applied Energy Research (UK-CAER), the University of Nevada (UN) at Reno, and Tennessee Technological University (TTU). This report presents the work performed during the program extension from June 1, 1991 through May 31, 1992.

  4. Nano-Chemomechanical Assessment of Organic Rich Shales

    Science.gov (United States)

    Abedi, S.; Slim, M. I.; Ferralis, N.; Ulm, F.

    2013-12-01

    Organic rich shales, a rapidly increasing source of fossil fuels, have recently gained significant attention from the geomechanics and geochemistry communities. Despite their importance, the chemomechanical characterization of organic rich shales remains a pressing challenge due to their highly heterogeneous microstructure, complex chemistry, and multiscale mechanical performances. Such complexity requires advanced and innovative characterization tools for a complete understanding of the role played by different constituents in the chemomechnaical properties at multiple scales. In this study, experimental and theoretical microporomechanics have been employed for assessing the microtexture and material invariant properties of clay-dominated organic rich shales at nanometer length scales. A novel experimental methodology consisting of instrumented nanoindenation experiments and Energy Dispersive X-ray Spectroscopy (EDX) is developed for the proper chemomechanical characterization of the main constituents of the composite shale material. Combining experimental characterization with micromechanical modeling, the material invariant properties and mesotexture of material main constituents are investigated. The results provide evidence that mature clay-dominated organic rich shale systems exhibit a kerogen stiffening of the mechanical properties of the elementary particles. Such a stiffening effect cannot be explained by classical micromechanics models based on mean-field theories and volume averaging where a property softening would be predicted. Furthermore, it is seen that the presence and chemical composition of organic matter affects mechanical properties of organic rich shales significantly. The role of kerogen maturity, type, and chemical composition on mechanical performance of the material is investigated by incorporating results from Raman Spectroscopy into the analysis. The results of this investigation are used to define a model of the fundamental building

  5. Black shale studies in Kentucky. Quarterly report

    Energy Technology Data Exchange (ETDEWEB)

    1978-09-01

    Work during the quarter was devoted to final interpretation, integration, and compilation of surface stratigraphic and petrologic data into deliverable documents for DOE, MERC. As of September, two such documents have been prepared. A thesis on black-shale outcrop stratigraphy from the two eastern Kentucky outcrop belts has been completed and will be included with the annual report and a thesis on the thin-section petrology of three eastern Kentucky cores has also been completed and will be included with the annual report. Also during this quarter the transition to two new parts of the project was started including map compilation and a paleontological--paleoecological study. Compilation of isopach, lithofacies, and structural contour maps depends largely on completion of the well-log inventory from which all the data are generated. At present, well-log inventories for 37 of the 41 eastern Kentucky counties (90%) have been completed. Work has begun, however, on compiling data from the completed county inventories. Work has also begun on the paleontological--paleoecological portion of the project. A research assistant has been found to complete a thesis study on this part of the project and he is currently engaged in preliminary research.

  6. Oil shale as an alternative energy source

    Energy Technology Data Exchange (ETDEWEB)

    Hepbasli, A. [Ege University, Izmir (Turkey). Mechanical Engineering Dept.

    2004-02-15

    Oil shale (OS) is one of the world's most important energy resources, and its use can be traced back to ancient times. The objective of this study is to investigate many aspects of OS as an alternative energy source in Turkey, giving Turkey's OS deposits, the history of oil in Turkey, and some studies conducted to evaluate OSs. Research into the utilization of Turkish OSs has been going on since the 1970s, while OSs comprise the second largest solid fuel deposit in Turkey after lignites. OS deposits in Turkey are widely distributed in middle and western Anatolia, with an estimated current reserve of approximately 1,865 million tons. Other potential areas in the north Anatolian fault zone are also under investigation. With the continuing decline of petroleum supplies, accompanied by increasing costs of petroleum-based products, OS may present opportunities for supplying some of Turkey's fossil energy needs in the years ahead. (author)

  7. The influence of global sea level changes on European shale distribution and gas exploration

    Energy Technology Data Exchange (ETDEWEB)

    Turner, P.; Cornelius, C.T.; Clarke, H. [Cuadrilla Resources Ltd., Staffordshire (United Kingdom)

    2010-07-01

    Technological advances in directional drilling and hydraulic fracturing technology have unlocked new supplies of shale gas from reservoirs that were previously considered to be uneconomic. Several companies, both experienced majors and small independents, are currently evaluating the unconventional resource potential of mainland Europe. This paper demonstrated that global sea level changes govern the distribution of marine black shales. The Hallam Curve was used in this study to identify periods of prospective gas shale deposition. In general, these correspond to post-glacial periods of relatively high sea level. Under-filled marginal sedimentary basins are key exploration targets. The geochemical and petrophysical characteristics of the shales deposited under these conditions are often comparable to North American shales, particularly the Barnett Shale which is currently in production. Many orogenic events influence European shales in terms of organic maturity, hydrocarbon generation and fracture generation. The main prospective horizons in ascending stratigraphic sequence are the Alum Shale, Llandovery Shale, Fammenian/Frasnian Shale, Serpukhovian Shale, Toarcian Shale, Kimmeridge Clay and the Tertiary Eocene and Oligocene shales common to central Europe. This paper presented the authors initial exploration strategy, with particular focus on the Lower Palaeozoic of central Europe, the Namurian of northwest England and the Jurassic Posidonia Formation of the Roer Valley Graben in Holland. The potential obstacles to unconventional exploration in Europe include restricted access to surface locations, high water usage, a lack of convenient pipeline infrastructure, strict environmental regulations, a high population density and lack of suitable drilling rigs and well completion equipment. 13 refs., 7 figs.

  8. NOVEL IN-SITU METAL AND MINERAL EXTRACTION TECHNOLOGY

    Energy Technology Data Exchange (ETDEWEB)

    Glenn O' Gorman; Hans von Michaelis; Gregory J. Olson

    2004-09-22

    This white paper summarizes the state of art of in-situ leaching of metals and minerals, and describes a new technology concept employing improved fragmentation of ores underground in order to prepare the ore for more efficient in-situ leaching, combined with technology to continuously improve solution flow patterns through the ore during the leaching process. The process parameters and economic benefits of combining the new concept with chemical and biological leaching are described. A summary is provided of the next steps required to demonstrate the technology with the goal of enabling more widespread use of in-situ leaching.

  9. In Situ Probe Science at Saturn

    Science.gov (United States)

    Atkinson, D.H.; Lunine, J.I.; Simon-Miller, A. A.; Atreya, S. K.; Brinckerhoff, W.; Colaprete, A.; Coustenis, A.; Fletcher, L. N.; Guillot, T.; Lebreton, J.-P.; hide

    2014-01-01

    A fundamental goal of solar system exploration is to understand the origin of the solar sys-tem, the initial stages, conditions, and processes by which the solar system formed, how the formation pro-cess was initiated, and the nature of the interstellar seed material from which the solar system was born. Key to understanding solar system formation and subsequent dynamical and chemical evolution is the origin and evolution of the giant planets and their atmospheres. Several theories have been put forward to explain the process of solar system formation, and the origin and evolution of the giant planets and their atmospheres. Each theory offers quantifiable predictions of the abundances of noble gases He, Ne, Ar, Kr, and Xe, and abundances of key isotopic ratios 4He3He, DH, 15N14N, 18O16O, and 13C12C. Detection of certain dis-equilibrium species, diagnostic of deeper internal pro-cesses and dynamics of the atmosphere, would also help discriminate between competing theories. Measurements of the critical abundance profiles of these key constituents into the deeper well-mixed at-mosphere must be complemented by measurements of the profiles of atmospheric structure and dynamics at high vertical resolution and also require in situ explora-tion. The atmospheres of the giant planets can also serve as laboratories to better understand the atmospheric chem-istries, dynamics, processes, and climates on all planets including Earth, and offer a context and provide a ground truth for exoplanets and exoplanetary systems. Additionally, Giant planets have long been thought to play a critical role in the development of potentially habitable planetary systems. In the context of giant planet science provided by the Galileo, Juno, and Cassini missions to Jupiter and Sat-urn, a small, relatively shallow Saturn probe capable of measuring abundances and isotopic ratios of key at-mospheric constituents, and atmospheric structure in-cluding pressures, temperatures, dynamics, and cloud

  10. satellite and in-situ measurements

    Directory of Open Access Journals (Sweden)

    José de Jesús Salas Pérez

    2005-01-01

    Full Text Available La distribución espacial y temporal de la circulación superficial de la Bahía de Banderas se obtuvo con el empleo de series temporales de rapidez de viento, temperatura superficial del mar (AVHR radiómetro y un termógrafo, nivel del mar y trazas ascendentes y descendentes del radar altimétrico ERS-2. El período que abarca dichos datos es de cuatro años, ya que comenzó en el verano de 1997 y finalizó en el invierno de 2002. La marea en la Bahía es mixta (F=0.25 con predominio del armónico M2. La bahía no muestra características de resonancia con la marea del mar abierto. Amplitudes promedio de 30 cms., resultan en corrientes de marea de pocos cms./s. Las bajas frecuencias (periodos mayores a tres días parecen ser los principales generadores de la circulación marina en esta área, en la que predomina el periodo estacional sobre los otros periodos. FEOs fueron aplicadas a las componentes de velocidad, calculadas con observaciones de altimetría medidas en la boca de la Bahía, las cuales mostraron dos principales distribuciones espaciales. El primer periodo de distribución, que se extendió desde febrero hasta julio, muestra un flujo de entrada por la porción norte/sur de la bahía, con un flujo de salida por su boca (distribución anticiclónica. El segundo periodo se extiende desde agosto hasta diciembre y es opuesto al primero (distribución ciclónica. Las características de la circulación aquí presentadas son hipotéticas y observaciones de velocidad medidas in-situ deben confirmarlas

  11. In Situ Observations of Seismic Wave Propagation

    Science.gov (United States)

    Hudson, Kenneth Stewart

    Instrumented geotechnical field sites are designed to capture the infrequent but critically important in situ case histories of ground response, deformation, and liquefaction during significant earthquakes that generate high intensity ground shaking and large strains. The University of California at Santa Barbara has been monitoring densely instrumented geotechnical array field sites for almost three decades, with continuous recording now for more than a decade. When seismic waves travel into soil with sufficiently large ground motions, the soil behaves nonlinearly meaning the shear modulus of the material decreases from the linear value observed during weak ground motions. The degraded shear modulus can continue to affect a site for a period of time by changing the soil response during smaller ground motions after the large event. Decreased shear modulus is inferred when a decrease of shear wave velocity between two sensors in a vertical downhole array is observed. This velocity is calculated by measuring the difference in shear wave arrival times between the sensors using normalized cross correlation. The trend of decreasing shear wave velocity with increasing peak ground acceleration is observed at multiple geotechnical array field sites. The length of time the decreased velocity remains following stronger shaking is analyzed using more than 450 events over more than a decade at the Wildlife Liquefaction Array (WLA). Using both monthly and yearly velocity averages between sensors, there is evidence that suggests the shear wave velocity remains low over a period of months following larger significant shaking events at the site. In addition, at WLA there is evidence that the decrease in shear wave velocity can be detected at ground motion levels as low as 20 cm/s2. Additionally at the Garner Valley Downhole Array, a permanent cross-hole experiment is used to measure velocity changes in the soil with changing water table height. An underground hammer source swings

  12. In-situ bitumen extraction associated with increased petrogenic polycyclic aromatic compounds in lake sediments from the Cold Lake heavy oil fields (Alberta, Canada).

    Science.gov (United States)

    Korosi, Jennifer B; Cooke, Colin A; Eickmeyer, David C; Kimpe, Linda E; Blais, Jules M

    2016-11-01

    Most future growth in the Alberta bituminous sands will be based on thermal in-situ recovery technologies. To date, however, most attention on the environmental effects of bitumen recovery has focused on surface mining in the Athabasca region. Recent uncontrolled bitumen flow-to-surface incidents (FTS; appearance at the surface of bitumen emulsions from deep subsurface recovery zones) reported at the Cold Lake heavy oil fields highlight the need to better understand the potential role of in-situ extraction as a source of contaminants to landscapes and surface waters. We analyzed sediment cores from a lake located ∼2 km away from a recent bitumen FTS incident to provide a long-term perspective on the delivery of metals, polycyclic aromatic compounds (PACs), and polychlorinated biphenyls (PCBs) to surface freshwaters, and to assess whether the onset of local in-situ bitumen extraction can be linked to contaminant increases in nearby lakes. An increase in alkyl PACs coincided with the onset and expansion of commercial in-situ bitumen extraction, and multiple lines of evidence indicate a petrogenic source for recent alkyl PAC enrichment. However, no coincident increase in vanadium (enriched in bitumen) occurred that would suggest the source of petrogenic PAC enrichment is direct input of bituminous particles. Our results show that, similar to surface mining in the Athabasca region, activities associated with in-situ extraction can increase the burden of petrogenic PACs in nearby lakes, but many questions still remain regarding the exact sources and pathways of PACs into the environment. Given that more than 80% of Alberta's bitumen reserves can only be accessed using in-situ technologies, we recommend that this be made a research priority. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Analytical Investigation for In Situ Stress Measurement with Rheological Stress Recovery Method and Its Application

    Directory of Open Access Journals (Sweden)

    Quansheng Liu

    2016-01-01

    Full Text Available In situ stress is one of the most important parameters in underground engineering. Due to the difficulty and weakness of current stress measurement methods in deep soft rock, a new one, rheological stress recovery (RSR method, to determine three-dimensional stress tensor is developed. It is supposed that rock stresses will recover gradually with time and can be measured by embedding transducers into the borehole. In order to explore the relationship between the measured recovery stress and the initial stress, analytical solutions are developed for the stress measurement process with RSR method in a viscoelastic surrounding rock. The results showed that the measured recovery stress would be more close to the initial stress if the rock mass has a better rheological property, and the property of grouting material should be close to that of rock mass. Then, the RSR method, as well as overcoring technique, was carried out to measure the in situ stresses in Pingdingshan Number 1 coal mines in Henan Province, China. The stress measurement results are basically in the same order, and the major principal stresses are approximately in the direction of NW-SE, which correlates well with the stress regime of Pingdingshan zone known from the tectonic movement history.

  14. Solar System Exploration Augmented by In-Situ Resource Utilization: Mercury and Saturn Propulsion Investigations

    Science.gov (United States)

    Palaszewski, Bryan

    2016-01-01

    Human and robotic missions to Mercury and Saturn are presented and analyzed with a range of propulsion options. Historical studies of space exploration, in-situ resource utilization (ISRU), and industrialization all point to the vastness of natural resources in the solar system. Advanced propulsion benefitted from these resources in many ways. While advanced propulsion systems were proposed in these historical studies, further investigation of nuclear options using high power nuclear thermal and nuclear pulse propulsion as well as advanced chemical propulsion can significantly enhance these scenarios. Updated analyses based on these historical visions will be presented. Nuclear thermal propulsion and ISRU enhanced chemical propulsion landers are assessed for Mercury missions. At Saturn, nuclear pulse propulsion with alternate propellant feed systems and Titan exploration with chemical propulsion options are discussed. In-situ resource utilization was found to be critical in making Mercury missions more amenable for human visits. At Saturn, refueling using local atmospheric mining was found to be difficult to impractical, while refueling the Saturn missions from Uranus was more practical and less complex.

  15. UV-vis in situ spectrometry data mining through linear and non linear analysis methods

    Directory of Open Access Journals (Sweden)

    Liliana López-Kleine

    2014-01-01

    Full Text Available Los espectrómetros UV-visibles son captores que registran la absorbancia de luz emitida por partículas suspendidas en el agua a diferentes longitudes de onda y proporcionan mediciones en continuo, las cuales pueden ser interpretadas como concentraciones de parámetros comúnmente usados para evaluar el estado físico-químico de cuerpos de agua. Parámetros clásicos usados para detectar la presencia de contaminación en el agua son los sólidos suspendidos totales (TSS y la demanda química de oxígeno (CDO. Métodos de análisis flexibles y eficientes son necesarios para extraer información útil para fines de gestión y monitoreo a partir de los datos multivariados que proporcionan los captores. Se han usado métodos de calibración de tipo regresión parcial por mínimos cuadrados parciales (PLS. Varios autores han demostrado la necesidad de realizar la calibración para cada tipo de datos y cada cuerpo de agua, así como explorar métodos de análisis lineales y no lineales para el análisis de datos UV-visible y para determinar su relación con parámetros clásicos. En este trabajo se aplican métodos de análisis multivariado lineales y no lineales para la minería de datos UV-vis de alta dimensión, los cuales resultan útiles para la identificación de relaciones entre parámetros y longitudes de onda, la detección de muestras atípicas, así como la detección de estructuras no lineales en los datos.

  16. Selenium in a Wyoming grassland community receiving wastewater from an in situ uranium mine

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Water, soil, vegetation, grasshoppers (Family Acrididae), bird eggs and bird livers collected at a 23.5 hectare (5 8 acres) grassland irrigated with wastewater from...

  17. Strengthening shale wellbore with silica nanoparticles drilling fluid

    Directory of Open Access Journals (Sweden)

    Yili Kang

    2016-06-01

    Full Text Available Nanoparticles have been widely used to reduce wellbore instability problems of shale formation. In this paper, nanoparticle-containing water-based drilling fluids (WBDFs and oil-based drilling fluids (OBDFs were evaluated by running three new tests including spontaneous imbibition, swelling rate and acoustic transit time. Results showed that, for the WBDFs, nanoparticles leaded to higher plastic viscosity (PV and yield point (YP, and lower API-filtration. Moreover, because pore throats of shale can be plugged by nanoparticles, imbibition amount, swelling rate, and Young's-modulus reduction of shale decreased significantly. Higher concentration of nanoparticles can induce better plugging effect. However, for the OBDFs, nanoparticles did not show these positive effects like the nano WBDFs, even leaded to some negative effects such as higher filtration and larger Young's-modulus reduction. The main reasons are that the silica nanoparticles can easily disperse in the WBDFs, and effectively prevent the filtrate invading into shale by plugging pore throats. But the same silica nanoparticles are difficult to disperse in OBDFs, and do not perform the expected functions. This study indicates that nano WBDFs have great potential to reduce the wellbore instability problems of shale formation.

  18. Numerical Investigation of Bedding Plane Parameters of Transversely Isotropic Shale

    Science.gov (United States)

    Chong, Zhaohui; Li, Xuehua; Hou, Peng; Wu, Yuechao; Zhang, Ji; Chen, Tian; Liang, Shun

    2017-05-01

    Determination of the physical properties of shale is receiving more attention as the numbers of shale gas exploration projects are initiated, and as hydraulic fracturing becomes an integral exploitation method. In particular, anisotropy caused by the bedding structure of shale needs specific attention. In this paper, an anisotropic mineral brittleness-based model (AMBBM) is proposed that makes use of the discrete element method (DEM) to study shale properties, such as anisotropy of non-penetrating bedding planes and separating brittle and non-brittle minerals. Micro-parameters of the AMBBM are calibrated using uniaxial compressive strength tests and by studying the parameter gradient of smooth joints (SJ), such that the strength of SJ mainly affects the failure load in Brazilian tests (FLBT). It is found that the ratio of cohesion to tensile strength of SJ mainly affects the number of cracks formed, which further leads to different failure modes. Normal stiffness and shear stiffness of SJ exerts different effects on FLBT and stiffness in the model. However, the percentage of cracks of various minerals is less affected. The degree of anisotropy is affected by the angle range of parallel bond replaced by bedding plane. Based on the results, a new validation method for AMBBM is proposed, given that the numerical results show good agreement with experimental results, such as FLBT, splitting modulus, and failure mode. The model can thus be used to study seepage properties of shale gas exploitation and hydraulic fracturing by DEM.

  19. Environmental public health dimensions of shale and tight gas development.

    Science.gov (United States)

    Shonkoff, Seth B C; Hays, Jake; Finkel, Madelon L

    2014-08-01

    The United States has experienced a boom in natural gas production due to recent technological innovations that have enabled this resource to be produced from shale formations. We reviewed the body of evidence related to exposure pathways in order to evaluate the potential environmental public health impacts of shale gas development. We highlight what is currently known and identify data gaps and research limitations by addressing matters of toxicity, exposure pathways, air quality, and water quality. There is evidence of potential environmental public health risks associated with shale gas development. Several studies suggest that shale gas development contributes to ambient air concentrations of pollutants known to be associated with increased risk of morbidity and mortality. Similarly, an increasing body of studies suggest that water contamination risks exist through a variety of environmental pathways, most notably during wastewater transport and disposal, and via poor zonal isolation of gases and fluids due to structural integrity impairment of cement in gas wells. Despite a growing body of evidence, data gaps persist. Most important, there is a need for more epidemiological studies to assess associations between risk factors, such as air and water pollution, and health outcomes among populations living in close proximity to shale gas operations.

  20. An apparent permeability model of shale gas under formation conditions

    Science.gov (United States)

    Chen, Peng; Jiang, Shan; Chen, Yan; Wang, Shanshan

    2017-08-01

    There are various types of pores in shale, mainly consisting of nanopores and micropores, causing flow regime variations and apparent permeability changes during the development of the reservoir. In this paper, a Knudsen number calculation model is proposed with the actual conditions of gas in a shale reservoir. Then, based on the distribution of pores in shale, an apparent permeability model is established using hydrodynamics, and a calculation method is put forward for the actual permeability of a reservoir. Finally, the Knudsen number model and the permeability correction coefficient model are used to analyze the flow regime and permeability correction coefficients in pores during the development of the shale gas reservoir. Results show that with a decreasing of pressure, the Knudsen number increases, the flow regime changes from continuous flow and slip flow to transition flow or free molecular flow. When the Knudsen number is Kn > 0.1, and with a further increasing of Kn, gas molecule slippage greatly intensifies and the permeability correction coefficient K app/Kd significantly increases. While the Knudsen number increases, the permeability correction coefficient significantly increases in the micropores and the small pores, but this does not appear in the macropores and the mesopores. These results can be used to guide flow regime analysis and production forecasting in shale gas reservoirs.