Software for the nuclear reactor dynamics study using time series processing

International Nuclear Information System (INIS)

Valero, Esbel T.; Montesino, Maria E.

1997-01-01

The parametric monitoring in Nuclear Power Plant (NPP) permits the operational surveillance of nuclear reactor. The methods employed in order to process this information such as FFT, autoregressive models and other, have some limitations when those regimens in which appear strongly non-linear behaviors are analyzed. In last years the chaos theory has offered new ways in order to explain complex dynamic behaviors. This paper describes a software (ECASET) that allow, by time series processing from NPP's acquisition system, to characterize the nuclear reactor dynamic as a complex dynamical system. Here we show using ECASET's results the possibility of classifying the different regimens appearing in nuclear reactors. The results of several temporal series processing from real systems are introduced. This type of analysis complements the results obtained with traditional methods and can constitute a new tool for monitoring nuclear reactors. (author). 13 refs., 3 figs

Software for the nuclear reactor dynamics study using time series processing; Software para el estudio de la dinamica de reactores nucleares mediante el procesamiento de series temporales

Energy Technology Data Exchange (ETDEWEB)

Valero, Esbel T.; Montesino, Maria E. [Instituto Superior de Ciencia y Tecnologia Nuclear (ISCTN), La Habana (Cuba)

1997-12-01

The parametric monitoring in Nuclear Power Plant (NPP) permits the operational surveillance of nuclear reactor. The methods employed in order to process this information such as FFT, autoregressive models and other, have some limitations when those regimens in which appear strongly non-linear behaviors are analyzed. In last years the chaos theory has offered new ways in order to explain complex dynamic behaviors. This paper describes a software (ECASET) that allow, by time series processing from NPP`s acquisition system, to characterize the nuclear reactor dynamic as a complex dynamical system. Here we show using ECASET`s results the possibility of classifying the different regimens appearing in nuclear reactors. The results of several temporal series processing from real systems are introduced. This type of analysis complements the results obtained with traditional methods and can constitute a new tool for monitoring nuclear reactors. (author). 13 refs., 3 figs.

Independent Verification and Validation Of SAPHIRE 8 Software Requirements Project Number: N6423 U.S. Nuclear Regulatory Commission

Energy Technology Data Exchange (ETDEWEB)

Kent Norris

2009-09-01

The purpose of the Independent Verification and Validation (IV&V) role in the evaluation of the SAPHIRE requirements definition is to assess the activities that results in the specification, documentation, and review of the requirements that the software product must satisfy, including functionality, performance, design constraints, attributes and external interfaces. The IV&V team began this endeavor after the software engineering and software development of SAPHIRE had already been in production. IV&V reviewed the requirements specified in the NRC Form 189s to verify these requirements were included in SAPHIRE’s Software Verification and Validation Plan (SVVP).

Sandia software guidelines: Software quality planning

Energy Technology Data Exchange (ETDEWEB)

1987-08-01

This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. In consonance with the IEEE Standard for Software Quality Assurance Plans, this volume identifies procedures to follow in producing a Software Quality Assurance Plan for an organization or a project, and provides an example project SQA plan. 2 figs., 4 tabs.

Modernising ATLAS Software Build Infrastructure

CERN Document Server

Gaycken, Goetz; The ATLAS collaboration

2017-01-01

In the last year ATLAS has radically updated its software development infrastructure hugely reducing the complexity of building releases and greatly improving build speed, flexibility and code testing. The first step in this transition was the adoption of CMake as the software build system over the older CMT. This required the development of an automated translation from the old system to the new, followed by extensive testing and improvements. This resulted in a far more standard build process that was married to the method of building ATLAS software as a series of 12 separate projects from SVN. We then proceeded with a migration of its code base from SVN to git. As the SVN repository had been structured to manage each package more or less independently there was no simple mapping that could be used to manage the migration into git. Instead a specialist set of scripts that captured the software changes across official software releases was developed. With some clean up of the repository and the policy of onl...

Problems in Analyzing Time Series with Gaps and Their Solution with the WinABD Software Package

Science.gov (United States)

Desherevskii, A. V.; Zhuravlev, V. I.; Nikolsky, A. N.; Sidorin, A. Ya.

2017-12-01

Technologies for the analysis of time series with gaps are considered. Some algorithms of signal extraction (purification) and evaluation of its characteristics, such as rhythmic components, are discussed for series with gaps. Examples are given for the analysis of data obtained during long-term observations at the Garm geophysical test site and in other regions. The technical solutions used in the WinABD software are considered to most efficiently arrange the operation of relevant algorithms in the presence of observational defects.

All-phase MR angiography using independent component analysis of dynamic contrast enhanced MRI time series. φ-MRA

International Nuclear Information System (INIS)

Suzuki, Kiyotaka; Matsuzawa, Hitoshi; Watanabe, Masaki; Nakada, Tsutomu; Nakayama, Naoki; Kwee, I.L.

2003-01-01

Dynamic contrast enhanced magnetic resonance imaging (dynamic MRI) represents a MRI version of non-diffusible tracer methods, the main clinical use of which is the physiological construction of what is conventionally referred to as perfusion images. The raw data utilized for constructing MRI perfusion images are time series of pixel signal alterations associated with the passage of a gadolinium containing contrast agent. Such time series are highly compatible with independent component analysis (ICA), a novel statistical signal processing technique capable of effectively separating a single mixture of multiple signals into their original independent source signals (blind separation). Accordingly, we applied ICA to dynamic MRI time series. The technique was found to be powerful, allowing for hitherto unobtainable assessment of regional cerebral hemodynamics in vivo. (author)

Software Design Challenges in Time Series Prediction Systems Using Parallel Implementation of Artificial Neural Networks

Directory of Open Access Journals (Sweden)

Narayanan Manikandan

2016-01-01

Full Text Available Software development life cycle has been characterized by destructive disconnects between activities like planning, analysis, design, and programming. Particularly software developed with prediction based results is always a big challenge for designers. Time series data forecasting like currency exchange, stock prices, and weather report are some of the areas where an extensive research is going on for the last three decades. In the initial days, the problems with financial analysis and prediction were solved by statistical models and methods. For the last two decades, a large number of Artificial Neural Networks based learning models have been proposed to solve the problems of financial data and get accurate results in prediction of the future trends and prices. This paper addressed some architectural design related issues for performance improvement through vectorising the strengths of multivariate econometric time series models and Artificial Neural Networks. It provides an adaptive approach for predicting exchange rates and it can be called hybrid methodology for predicting exchange rates. This framework is tested for finding the accuracy and performance of parallel algorithms used.

Global Crisis as Enterprise Software Motivator: from Lifecycle Optimization to Efficient Implementation Series

Directory of Open Access Journals (Sweden)

Sergey V. Zykov

2012-04-01

Full Text Available It is generally known that software system development lifecycle (SSDL should be managed adequately. The global economy crisis and subsequent depression have taught us certain lessons on the subject, which is so vital for enterprises. The paper presents the adaptive methodology of enterprise SSDL, which allows to avoid "local crises" while producing large-scale software. The methodology is based on extracting common ERP module level patterns and applying them to series of heterogeneous implementations. The approach includes a lifecycle model, which extends conventional spiral model by formal data representation/management models and DSL-based "low-level" CASE tools supporting the formalisms. The methodology has been successfully implemented as a series of portal-based ERP systems in ITERA oil-and-gas corporation, and in a number of trading/banking enterprise applications for other enterprises. Semantic network-based airline dispatch system, and a 6D-model-driven nuclear power plant construction support system are currently in progress. Combining various SSDL models is discussed. Terms-and-cost reduction factors are examined. Correcting SSDL according to project size and scope is overviewed. The so-called “human factor errors” resulting from non-systematic SSDL approach, and their influencing crisis and depression, are analyzed. The ways to systematic and efficient SSDL are outlined. Troubleshooting advises are given for the problems concerned.

Statistical Software for State Space Methods

Directory of Open Access Journals (Sweden)

Jacques J. F. Commandeur

2011-05-01

Full Text Available In this paper we review the state space approach to time series analysis and establish the notation that is adopted in this special volume of the Journal of Statistical Software. We first provide some background on the history of state space methods for the analysis of time series. This is followed by a concise overview of linear Gaussian state space analysis including the modelling framework and appropriate estimation methods. We discuss the important class of unobserved component models which incorporate a trend, a seasonal, a cycle, and fixed explanatory and intervention variables for the univariate and multivariate analysis of time series. We continue the discussion by presenting methods for the computation of different estimates for the unobserved state vector: filtering, prediction, and smoothing. Estimation approaches for the other parameters in the model are also considered. Next, we discuss how the estimation procedures can be used for constructing confidence intervals, detecting outlier observations and structural breaks, and testing model assumptions of residual independence, homoscedasticity, and normality. We then show how ARIMA and ARIMA components models fit in the state space framework to time series analysis. We also provide a basic introduction for non-Gaussian state space models. Finally, we present an overview of the software tools currently available for the analysis of time series with state space methods as they are discussed in the other contributions to this special volume.

Developing a complex independent component analysis technique to extract non-stationary patterns from geophysical time-series

Science.gov (United States)

Forootan, Ehsan; Kusche, Jürgen

2016-04-01

Geodetic/geophysical observations, such as the time series of global terrestrial water storage change or sea level and temperature change, represent samples of physical processes and therefore contain information about complex physical interactionswith many inherent time scales. Extracting relevant information from these samples, for example quantifying the seasonality of a physical process or its variability due to large-scale ocean-atmosphere interactions, is not possible by rendering simple time series approaches. In the last decades, decomposition techniques have found increasing interest for extracting patterns from geophysical observations. Traditionally, principal component analysis (PCA) and more recently independent component analysis (ICA) are common techniques to extract statistical orthogonal (uncorrelated) and independent modes that represent the maximum variance of observations, respectively. PCA and ICA can be classified as stationary signal decomposition techniques since they are based on decomposing the auto-covariance matrix or diagonalizing higher (than two)-order statistical tensors from centered time series. However, the stationary assumption is obviously not justifiable for many geophysical and climate variables even after removing cyclic components e.g., the seasonal cycles. In this paper, we present a new decomposition method, the complex independent component analysis (CICA, Forootan, PhD-2014), which can be applied to extract to non-stationary (changing in space and time) patterns from geophysical time series. Here, CICA is derived as an extension of real-valued ICA (Forootan and Kusche, JoG-2012), where we (i) define a new complex data set using a Hilbert transformation. The complex time series contain the observed values in their real part, and the temporal rate of variability in their imaginary part. (ii) An ICA algorithm based on diagonalization of fourth-order cumulants is then applied to decompose the new complex data set in (i

Open-source Software for Demand Forecasting of Clinical Laboratory Test Volumes Using Time-series Analysis.

Science.gov (United States)

Mohammed, Emad A; Naugler, Christopher

2017-01-01

Demand forecasting is the area of predictive analytics devoted to predicting future volumes of services or consumables. Fair understanding and estimation of how demand will vary facilitates the optimal utilization of resources. In a medical laboratory, accurate forecasting of future demand, that is, test volumes, can increase efficiency and facilitate long-term laboratory planning. Importantly, in an era of utilization management initiatives, accurately predicted volumes compared to the realized test volumes can form a precise way to evaluate utilization management initiatives. Laboratory test volumes are often highly amenable to forecasting by time-series models; however, the statistical software needed to do this is generally either expensive or highly technical. In this paper, we describe an open-source web-based software tool for time-series forecasting and explain how to use it as a demand forecasting tool in clinical laboratories to estimate test volumes. This tool has three different models, that is, Holt-Winters multiplicative, Holt-Winters additive, and simple linear regression. Moreover, these models are ranked and the best one is highlighted. This tool will allow anyone with historic test volume data to model future demand.

Open-source software for demand forecasting of clinical laboratory test volumes using time-series analysis

Directory of Open Access Journals (Sweden)

Emad A Mohammed

2017-01-01

Full Text Available Background: Demand forecasting is the area of predictive analytics devoted to predicting future volumes of services or consumables. Fair understanding and estimation of how demand will vary facilitates the optimal utilization of resources. In a medical laboratory, accurate forecasting of future demand, that is, test volumes, can increase efficiency and facilitate long-term laboratory planning. Importantly, in an era of utilization management initiatives, accurately predicted volumes compared to the realized test volumes can form a precise way to evaluate utilization management initiatives. Laboratory test volumes are often highly amenable to forecasting by time-series models; however, the statistical software needed to do this is generally either expensive or highly technical. Method: In this paper, we describe an open-source web-based software tool for time-series forecasting and explain how to use it as a demand forecasting tool in clinical laboratories to estimate test volumes. Results: This tool has three different models, that is, Holt-Winters multiplicative, Holt-Winters additive, and simple linear regression. Moreover, these models are ranked and the best one is highlighted. Conclusion: This tool will allow anyone with historic test volume data to model future demand.

Evolving software products, the design of a water-related modeling software ecosystem

DEFF Research Database (Denmark)

Manikas, Konstantinos

2017-01-01

more than 50 years ago. However, a radical change of software products to evolve both in the software engineering as much as the organizational and business aspects in a disruptive manner are rather rare. In this paper, we report on the transformation of one of the market leader product series in water......-related calculation and modeling from a traditional business-as-usual series of products to an evolutionary software ecosystem. We do so by relying on existing concepts on software ecosystem analysis to analyze the future ecosystem. We report and elaborate on the main focus points necessary for this transition. We...... argue for the generalization of our focus points to the transition from traditional business-as-usual software products to software ecosystems....

Software Independent Verification and Validation (SIV&V) Simplified

Science.gov (United States)

2006-12-01

Midcourse Defense GOTS Government-Off-The-Shelf GSAM General Service Administration Acquisition Manual GTE General Telephone and Electronics GUI...Graphical User Interfaces HSI Hardware and Software Integration HSI Human Systems Integration HTP Hardware Test Plan HWCI Hardware...requirements are extracted and traced to the developer’s Software and Hardware Test Plans (STP and HTP ). This ensures adequacy of the test plans and also

Testing independence between two Poisson-generated multinomial variables in case-series and cohort studies.

Science.gov (United States)

Hocine, Mounia; Guillemot, Didier; Tubert-Bitter, Pascale; Moreau, Thierry

2005-12-30

In case-series or cohort studies, we propose a test of independence between the occurrences of two types of recurrent events (such as two repeated infections) related to an intermittent exposure (such as an antibiotic treatment). The test relies upon an extension of a recent method for analysing case-series data, in the presence of one type of recurrent event. The test statistic is derived from a bivariate Poisson generated-multinomial distribution. Simulations for checking the validity of the test concerning the type I error and the power properties are presented. The test is illustrated using data from a cohort on antibiotics bacterial resistance in schoolchildren. Copyright 2005 John Wiley & Sons, Ltd.

Statistical Software Engineering

Science.gov (United States)

1998-04-13

multiversion software subject to coincident errors. IEEE Trans. Software Eng. SE-11:1511-1517. Eckhardt, D.E., A.K Caglayan, J.C. Knight, L.D. Lee, D.F...J.C. and N.G. Leveson. 1986. Experimental evaluation of the assumption of independence in multiversion software. IEEE Trans. Software

Framework for Small-Scale Experiments in Software Engineering: Guidance and Control Software Project: Software Engineering Case Study

Science.gov (United States)

Hayhurst, Kelly J.

1998-01-01

Software is becoming increasingly significant in today's critical avionics systems. To achieve safe, reliable software, government regulatory agencies such as the Federal Aviation Administration (FAA) and the Department of Defense mandate the use of certain software development methods. However, little scientific evidence exists to show a correlation between software development methods and product quality. Given this lack of evidence, a series of experiments has been conducted to understand why and how software fails. The Guidance and Control Software (GCS) project is the latest in this series. The GCS project is a case study of the Requirements and Technical Concepts for Aviation RTCA/DO-178B guidelines, Software Considerations in Airborne Systems and Equipment Certification. All civil transport airframe and equipment vendors are expected to comply with these guidelines in building systems to be certified by the FAA for use in commercial aircraft. For the case study, two implementations of a guidance and control application were developed to comply with the DO-178B guidelines for Level A (critical) software. The development included the requirements, design, coding, verification, configuration management, and quality assurance processes. This paper discusses the details of the GCS project and presents the results of the case study.

Independent component analysis: A new possibility for analysing series of electron energy loss spectra

International Nuclear Information System (INIS)

Bonnet, Nogl; Nuzillard, Danielle

2005-01-01

A complementary approach is proposed for analysing series of electron energy-loss spectra that can be recorded with the spectrum-line technique, across an interface for instance. This approach, called blind source separation (BSS) or independent component analysis (ICA), complements two existing methods: the spatial difference approach and multivariate statistical analysis. The principle of the technique is presented and illustrations are given through one simulated example and one real example

Repository Evaluation of Software Reuse

OpenAIRE

Banker, Rajiv D.; Kauffman, Robert J.; Zweig, Dani

1993-01-01

The article of record as published may be found at: 10.1109/32.223805 Center for Digital Economy Research Stem School of Business Working Paper IS-93-28, Replaces: Working Paper IS-93-1 Working Paper Series STERN IS-93-28 Working Paper series: STERN IS-93-28 The traditional unit of analysis and control for software managers is the software project, and subsequently the resulting application system. Today, with the emerging ca- pabilities of computer-aided software engineering ...

SaaS Platform for Time Series Data Handling

Science.gov (United States)

Oplachko, Ekaterina; Rykunov, Stanislav; Ustinin, Mikhail

2018-02-01

The paper is devoted to the description of MathBrain, a cloud-based resource, which works as a "Software as a Service" model. It is designed to maximize the efficiency of the current technology and to provide a tool for time series data handling. The resource provides access to the following analysis methods: direct and inverse Fourier transforms, Principal component analysis and Independent component analysis decompositions, quantitative analysis, magnetoencephalography inverse problem solution in a single dipole model based on multichannel spectral data.

Global Software Engineering

DEFF Research Database (Denmark)

Ebert, Christof; Kuhrmann, Marco; Prikladnicki, Rafael

2016-01-01

Professional software products and IT systems and services today are developed mostly by globally distributed teams, projects, and companies. Successfully orchestrating Global Software Engineering (GSE) has become the major success factor both for organizations and practitioners. Yet, more than...... and experience reported at the IEEE International Conference on Software Engineering (ICGSE) series. The outcomes of our analysis show GSE as a field highly attached to industry and, thus, a considerable share of ICGSE papers address the transfer of Software Engineering concepts and solutions to the global stage...

Software Classifications: Trends in Literacy Software Publication and Marketing.

Science.gov (United States)

Balajthy, Ernest

First in a continuing series of reports on trends in marketing and publication of software for literacy education, a study explored the development of a database to track the trends and reported on trends seen in 1995. The final version of the 1995 database consisted of 1011 software titles, 165 of which had been published in 1995 and 846…

FTSPlot: fast time series visualization for large datasets.

Directory of Open Access Journals (Sweden)

Michael Riss

Full Text Available The analysis of electrophysiological recordings often involves visual inspection of time series data to locate specific experiment epochs, mask artifacts, and verify the results of signal processing steps, such as filtering or spike detection. Long-term experiments with continuous data acquisition generate large amounts of data. Rapid browsing through these massive datasets poses a challenge to conventional data plotting software because the plotting time increases proportionately to the increase in the volume of data. This paper presents FTSPlot, which is a visualization concept for large-scale time series datasets using techniques from the field of high performance computer graphics, such as hierarchic level of detail and out-of-core data handling. In a preprocessing step, time series data, event, and interval annotations are converted into an optimized data format, which then permits fast, interactive visualization. The preprocessing step has a computational complexity of O(n x log(N; the visualization itself can be done with a complexity of O(1 and is therefore independent of the amount of data. A demonstration prototype has been implemented and benchmarks show that the technology is capable of displaying large amounts of time series data, event, and interval annotations lag-free with < 20 ms ms. The current 64-bit implementation theoretically supports datasets with up to 2(64 bytes, on the x86_64 architecture currently up to 2(48 bytes are supported, and benchmarks have been conducted with 2(40 bytes/1 TiB or 1.3 x 10(11 double precision samples. The presented software is freely available and can be included as a Qt GUI component in future software projects, providing a standard visualization method for long-term electrophysiological experiments.

Minerva: using a software program to improve resident performance during independent call

Science.gov (United States)

Itri, Jason N.; Redfern, Regina O.; Cook, Tessa; Scanlon, Mary H.

2010-03-01

We have developed an application called Minerva that allows tracking of resident discrepancy rates and missed cases. Minerva mines the radiology information system (RIS) for preliminary interpretations provided by residents during independent call and copies both the preliminary and final interpretations to a database. Both versions are displayed for direct comparison by Minerva and classified as 'in agreement', 'minor discrepancy' or 'major discrepancy' by the resident program director. Minerva compiles statistics comparing minor, major and total discrepancy rates for individual residents relative to the overall group. Discrepant cases are categorized according to date, modality and body part and reviewed for trends in missed cases. The rate of minor, major and total discrepancies for residents on-call at our institution was similar to rates previously published, including a 2.4% major discrepancy rate for second year radiology residents in the DePICTORS study and a 2.6% major discrepancy rate for resident at a community hospital. Trend analysis of missed cases was used to generate a topic-specific resident missed case conference on acromioclavicular (AC) joint separation injuries, which resulted in a 75% decrease in the number of missed cases related to AC separation subsequent to the conference. Using a software program to track of minor and major discrepancy rates for residents taking independent call using modified RadPeer scoring guidelines provides a competency-based metric to determine resident performance. Topic-specific conferences using the cases identified by Minerva can result in a decrease in missed cases.

RIPE [robot independent programming environment]: A robot independent programming environment

International Nuclear Information System (INIS)

Miller, D.J.; Lennox, R.C.

1990-01-01

Remote manual operations in radiation environments are typically performed very slowly. Sensor-based computer-controlled robots hold great promise for increasing the speed and safety of remote operations; however, the programming of robotic systems has proven to be expensive and difficult. Generalized approaches to robot programming that reuse available software modules and employ programming languages which are independent of the specific robotic and sensory devices being used are needed to speed software development and increase overall system reliability. This paper discusses the robot independent programming environment (RIPE) developed at Sandia National Laboratories (SNL). The RIPE is an object-oriented approach to robot system architectures; it is a software environment that facilitates rapid design and implementation of complex robot systems for diverse applications. An architecture based on hierarchies of distributed multiprocessors provides the computing platform for a layered programming structure that models applications using software objects. These objects are designed to support model-based automated programming of robotic and machining devices, real-time sensor-based control, error handling, and robust communication

Evaluation of high-performance computing software

Energy Technology Data Exchange (ETDEWEB)

Browne, S.; Dongarra, J. [Univ. of Tennessee, Knoxville, TN (United States); Rowan, T. [Oak Ridge National Lab., TN (United States)

1996-12-31

The absence of unbiased and up to date comparative evaluations of high-performance computing software complicates a user`s search for the appropriate software package. The National HPCC Software Exchange (NHSE) is attacking this problem using an approach that includes independent evaluations of software, incorporation of author and user feedback into the evaluations, and Web access to the evaluations. We are applying this approach to the Parallel Tools Library (PTLIB), a new software repository for parallel systems software and tools, and HPC-Netlib, a high performance branch of the Netlib mathematical software repository. Updating the evaluations with feed-back and making it available via the Web helps ensure accuracy and timeliness, and using independent reviewers produces unbiased comparative evaluations difficult to find elsewhere.

Software Product Manager: A Mechanism to manage software products in small and medium ISVs

NARCIS (Netherlands)

Katchow, R.; van de Weerd, I.; Brinkkemper, S.; Rooswinkel, A.

2009-01-01

In this paper, we present SP Manager as an innovative tool for managing software products in small and medium independent software vendors (ISVs). This tool incorporates the operational software product management (SPM) processes focused on requirements management and release planning. By using

The Feldenkrais Method(®) can enhance cognitive function in independent living older adults: A case-series.

Science.gov (United States)

Ullmann, Gerhild; Williams, Harriet G

2016-07-01

Poor cognitive health a major concern of aging individuals, can compromise independent living. More than 16 million people in the United States are affected by cognitive impairment. We have studied the effects of the Feldenkrais Method(®) on cognitive function. In this case series with three participants cognitive function was assessed with the Trail Making Test A and B at baseline and after the Feldenkrais intervention. All participants improved performance on Trail Making Test A and B after completing the Feldenkrais intervention indicating that Feldenkrais lessons may offset age-related decline in cognitive function. The results of this case series warrant larger scale studies on cognitive outcomes of Feldenkrais interventions in clinical and non-clinical populations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Software component quality evaluation

Science.gov (United States)

Clough, A. J.

1991-01-01

The paper describes a software inspection process that can be used to evaluate the quality of software components. Quality criteria, process application, independent testing of the process and proposed associated tool support are covered. Early results indicate that this technique is well suited for assessing software component quality in a standardized fashion. With automated machine assistance to facilitate both the evaluation and selection of software components, such a technique should promote effective reuse of software components.

Desiderata for Linguistic Software Design

Science.gov (United States)

Garretson, Gregory

2008-01-01

This article presents a series of guidelines both for researchers in search of software to be used in linguistic analysis and for programmers designing such software. A description of the intended audience and the types of software under consideration and a review of some relevant literature are followed by a discussion of several important…

ITS Version 3.0: Powerful, user-friendly software for radiation modelling

International Nuclear Information System (INIS)

Kensek, R.P.; Halbleib, J.A.; Valdez, G.D.

1993-01-01

ITS (the Integrated Tiger Series) is a powerful, but user-friendly, software package permitting state-of-the-art modelling of electron and/or photon radiation effects. The programs provide Monte Carlo solution of linear time-independent coupled electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields. The ITS system combines operational simplicity and physical accuracy in order to provide experimentalist and theorists alike with a method for the routine but rigorous solution of sophisticated radiation transport problems

The independence of software metrics taken at different life-cycle stages

Science.gov (United States)

Kafura, D.; Canning, J.; Reddy, G.

1984-01-01

Over the past few years a large number of software metrics have been proposed and, in varying degrees, a number of these metrics have been subjected to empirical validation which demonstrated the utility of the metrics in the software development process. Attempts to classify these metrics and to determine if the metrics in these different classes appear to be measuring distinct attributes of the software product are studied. Statistical analysis is used to determine the degree of relationship among the metrics.

Patient-specific IMRT verification using independent fluence-based dose calculation software: experimental benchmarking and initial clinical experience

International Nuclear Information System (INIS)

Georg, Dietmar; Stock, Markus; Kroupa, Bernhard; Olofsson, Joergen; Nyholm, Tufve; Ahnesjoe, Anders; Karlsson, Mikael

2007-01-01

Experimental methods are commonly used for patient-specific intensity-modulated radiotherapy (IMRT) verification. The purpose of this study was to investigate the accuracy and performance of independent dose calculation software (denoted as 'MUV' (monitor unit verification)) for patient-specific quality assurance (QA). 52 patients receiving step-and-shoot IMRT were considered. IMRT plans were recalculated by the treatment planning systems (TPS) in a dedicated QA phantom, in which an experimental 1D and 2D verification (0.3 cm 3 ionization chamber; films) was performed. Additionally, an independent dose calculation was performed. The fluence-based algorithm of MUV accounts for collimator transmission, rounded leaf ends, tongue-and-groove effect, backscatter to the monitor chamber and scatter from the flattening filter. The dose calculation utilizes a pencil beam model based on a beam quality index. DICOM RT files from patient plans, exported from the TPS, were directly used as patient-specific input data in MUV. For composite IMRT plans, average deviations in the high dose region between ionization chamber measurements and point dose calculations performed with the TPS and MUV were 1.6 ± 1.2% and 0.5 ± 1.1% (1 S.D.). The dose deviations between MUV and TPS slightly depended on the distance from the isocentre position. For individual intensity-modulated beams (total 367), an average deviation of 1.1 ± 2.9% was determined between calculations performed with the TPS and with MUV, with maximum deviations up to 14%. However, absolute dose deviations were mostly less than 3 cGy. Based on the current results, we aim to apply a confidence limit of 3% (with respect to the prescribed dose) or 6 cGy for routine IMRT verification. For off-axis points at distances larger than 5 cm and for low dose regions, we consider 5% dose deviation or 10 cGy acceptable. The time needed for an independent calculation compares very favourably with the net time for an experimental approach

Compiler issues associated with safety-related software

International Nuclear Information System (INIS)

Feinauer, L.R.

1991-01-01

A critical issue in the quality assurance of safety-related software is the ability of the software to produce identical results, independent of the host machine, operating system, or compiler version under which the software is installed. A study is performed using the VIPRE-0l, FREY-01, and RETRAN-02 safety-related codes. Results from an IBM 3083 computer are compared with results from a CYBER 860 computer. All three of the computer programs examined are written in FORTRAN; the VIPRE code uses the FORTRAN 66 compiler, whereas the FREY and RETRAN codes use the FORTRAN 77 compiler. Various compiler options are studied to determine their effect on the output between machines. Since the Control Data Corporation and IBM machines inherently represent numerical data differently, methods of producing equivalent accuracy of data representation were an important focus of the study. This paper identifies particular problems in the automatic double-precision option (AUTODBL) of the IBM FORTRAN 1.4.x series of compilers. The IBM FORTRAN version 2 compilers provide much more stable, reliable compilation for engineering software. Careful selection of compilers and compiler options can help guarantee identical results between different machines. To ensure reproducibility of results, the same compiler and compiler options should be used to install the program as were used in the development and testing of the program

An integrated development framework for rapid development of platform-independent and reusable satellite on-board software

Science.gov (United States)

Ziemke, Claas; Kuwahara, Toshinori; Kossev, Ivan

2011-09-01

Even in the field of small satellites, the on-board data handling subsystem has become complex and powerful. With the introduction of powerful CPUs and the availability of considerable amounts of memory on-board a small satellite it has become possible to utilize the flexibility and power of contemporary platform-independent real-time operating systems. Especially the non-commercial sector such like university institutes and community projects such as AMSAT or SSETI are characterized by the inherent lack of financial as well as manpower resources. The opportunity to utilize such real-time operating systems will contribute significantly to achieve a successful mission. Nevertheless the on-board software of a satellite is much more than just an operating system. It has to fulfill a multitude of functional requirements such as: Telecommand interpretation and execution, execution of control loops, generation of telemetry data and frames, failure detection isolation and recovery, the communication with peripherals and so on. Most of the aforementioned tasks are of generic nature and have to be conducted on any satellite with only minor modifications. A general set of functional requirements as well as a protocol for communication is defined in the SA ECSS-E-70-41A standard "Telemetry and telecommand packet utilization". This standard not only defines the communication protocol of the satellite-ground link but also defines a set of so called services which have to be available on-board of every compliant satellite and which are of generic nature. In this paper, a platform-independent and reusable framework is described which is implementing not only the ECSS-E-70-41A standard but also functionalities for interprocess communication, scheduling and a multitude of tasks commonly performed on-board of a satellite. By making use of the capabilities of the high-level programming language C/C++, the powerful open source library BOOST, the real-time operating system RTEMS and

Third-Party Software's Trust Quagmire.

Science.gov (United States)

Voas, J; Hurlburt, G

2015-12-01

Current software development has trended toward the idea of integrating independent software sub-functions to create more complete software systems. Software sub-functions are often not homegrown - instead they are developed by unknown 3 rd party organizations and reside in software marketplaces owned or controlled by others. Such software sub-functions carry plausible concern in terms of quality, origins, functionality, security, interoperability, to name a few. This article surveys key technical difficulties in confidently building systems from acquired software sub-functions by calling out the principle software supply chain actors.

Proceedings of the 19th Annual Software Engineering Workshop

Science.gov (United States)

1994-01-01

The Software Engineering Laboratory (SEL) is an organization sponsored by NASA/GSFC and created to investigate the effectiveness of software engineering technologies when applied to the development of applications software. The goals of the SEL are: (1) to understand the software development process in the GSFC environment; (2) to measure the effects of various methodologies, tools, and models on this process; and (3) to identify and then to apply successful development practices. The activities, findings, and recommendations of the SEL are recorded in the Software Engineering Laboratory Series, a continuing series of reports that include this document.

Software Process Improvement: Blueprints versus Recipes

DEFF Research Database (Denmark)

Aaen, Ivan

2003-01-01

Viewing software processes as blueprints emphasizes that design is separate from use, and thus that software process designers and users are independent. In the approach presented here, software processes are viewed as recipes; developers individually and collectively design their own software...... processes through facilitation, reflection, and improvisation. Udgivelsesdato: SEP-OCT...

Sandia Software Guidelines, Volume 2. Documentation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. In consonance with the IEEE Standards for software documentation, this volume provides guidance in the selection of an adequate document set for a software project and example formats for many types of software documentation. A tutorial on life cycle documentation is also provided. Extended document thematic outlines and working examples of software documents are available on electronic media as an extension of this volume.

PRISM, Processing and Review Interface for Strong Motion Data Software

Science.gov (United States)

Kalkan, E.; Jones, J. M.; Stephens, C. D.; Ng, P.

2016-12-01

A continually increasing number of high-quality digital strong-motion records from stations of the National Strong Motion Project (NSMP) of the U.S. Geological Survey (USGS), as well as data from regional seismic networks within the U.S., calls for automated processing of strong-motion records with human review limited to selected significant or flagged records. The NSMP has developed the Processing and Review Interface for Strong Motion data (PRISM) software to meet this need. PRISM automates the processing of strong-motion records by providing batch-processing capabilities. The PRISM software is platform-independent (coded in Java), open-source, and does not depend on any closed-source or proprietary software. The software consists of two major components: a record processing engine composed of modules for each processing step, and a graphical user interface (GUI) for manual review and processing. To facilitate the use by non-NSMP earthquake engineers and scientists, PRISM (both its processing engine and GUI components) is easy to install and run as a stand-alone system on common operating systems such as Linux, OS X and Windows. PRISM was designed to be flexible and extensible in order to accommodate implementation of new processing techniques. Input to PRISM currently is limited to data files in the Consortium of Organizations for Strong-Motion Observation Systems (COSMOS) V0 format, so that all retrieved acceleration time series need to be converted to this format. Output products include COSMOS V1, V2 and V3 files as: (i) raw acceleration time series in physical units with mean removed (V1), (ii) baseline-corrected and filtered acceleration, velocity, and displacement time series (V2), and (iii) response spectra, Fourier amplitude spectra and common earthquake-engineering intensity measures (V3). A thorough description of the record processing features supported by PRISM is presented with examples and validation results. All computing features have been

Software Quality Assurance Audits Guidebooks

Science.gov (United States)

1990-01-01

The growth in cost and importance of software to NASA has caused NASA to address the improvement of software development across the agency. One of the products of this program is a series of guidebooks that define a NASA concept of the assurance processes that are used in software development. The Software Assurance Guidebook, NASA-GB-A201, issued in September, 1989, provides an overall picture of the NASA concepts and practices in software assurance. Second level guidebooks focus on specific activities that fall within the software assurance discipline, and provide more detailed information for the manager and/or practitioner. This is the second level Software Quality Assurance Audits Guidebook that describes software quality assurance audits in a way that is compatible with practices at NASA Centers.

Development of design and analysis software for advanced nuclear system

International Nuclear Information System (INIS)

Wu Yican; Hu Liqin; Long Pengcheng; Luo Yuetong; Li Yazhou; Zeng Qin; Lu Lei; Zhang Junjun; Zou Jun; Xu Dezheng; Bai Yunqing; Zhou Tao; Chen Hongli; Peng Lei; Song Yong; Huang Qunying

2010-01-01

A series of professional codes, which are necessary software tools and data libraries for advanced nuclear system design and analysis, were developed by the FDS Team, including the codes of automatic modeling, physics and engineering calculation, virtual simulation and visualization, system engineering and safety analysis and the related database management etc. The development of these software series was proposed as an exercise of development of nuclear informatics. This paper introduced the main functions and key techniques of the software series, as well as some tests and practical applications. (authors)

Characterization of Ground Displacement Sources from Variational Bayesian Independent Component Analysis of Space Geodetic Time Series

Science.gov (United States)

Gualandi, Adriano; Serpelloni, Enrico; Elina Belardinelli, Maria; Bonafede, Maurizio; Pezzo, Giuseppe; Tolomei, Cristiano

2015-04-01

A critical point in the analysis of ground displacement time series, as those measured by modern space geodetic techniques (primarly continuous GPS/GNSS and InSAR) is the development of data driven methods that allow to discern and characterize the different sources that generate the observed displacements. A widely used multivariate statistical technique is the Principal Component Analysis (PCA), which allows to reduce the dimensionality of the data space maintaining most of the variance of the dataset explained. It reproduces the original data using a limited number of Principal Components, but it also shows some deficiencies, since PCA does not perform well in finding the solution to the so-called Blind Source Separation (BSS) problem. The recovering and separation of the different sources that generate the observed ground deformation is a fundamental task in order to provide a physical meaning to the possible different sources. PCA fails in the BSS problem since it looks for a new Euclidean space where the projected data are uncorrelated. Usually, the uncorrelation condition is not strong enough and it has been proven that the BSS problem can be tackled imposing on the components to be independent. The Independent Component Analysis (ICA) is, in fact, another popular technique adopted to approach this problem, and it can be used in all those fields where PCA is also applied. An ICA approach enables us to explain the displacement time series imposing a fewer number of constraints on the model, and to reveal anomalies in the data such as transient deformation signals. However, the independence condition is not easy to impose, and it is often necessary to introduce some approximations. To work around this problem, we use a variational bayesian ICA (vbICA) method, which models the probability density function (pdf) of each source signal using a mix of Gaussian distributions. This technique allows for more flexibility in the description of the pdf of the sources

The Integrated Tiger Series version 5.0

International Nuclear Information System (INIS)

Laub, Th.W.; Kensek, R.P.; Franke, B.C.; Lorence, L.J.; Crawford, M.J.; Quirk, Th.J.

2005-01-01

The Integrated Tiger Series (ITS) is a powerful and user-friendly software package permitting Monte Carlo solution of linear time-independent coupled electron/photon radiation transport problems, with or without the presence of macroscopic electric and magnetic fields of arbitrary spatial dependence. The package contains programs to perform 1-, 2-, and 3-dimensional simulations. Improvements in the ITS code package since the release of version 3.0 include improved physics, multigroup and adjoint capabilities, Computer-Aided Design geometry tracking, parallel implementations of all ITS codes, and more automated sub-zoning capabilities. These improvements and others are described as current or planned development efforts. The ITS package is currently at version 5.0. (authors)

Software Engineering Improvement Plan

Science.gov (United States)

2006-01-01

In performance of this task order, bd Systems personnel provided support to the Flight Software Branch and the Software Working Group through multiple tasks related to software engineering improvement and to activities of the independent Technical Authority (iTA) Discipline Technical Warrant Holder (DTWH) for software engineering. To ensure that the products, comments, and recommendations complied with customer requirements and the statement of work, bd Systems personnel maintained close coordination with the customer. These personnel performed work in areas such as update of agency requirements and directives database, software effort estimation, software problem reports, a web-based process asset library, miscellaneous documentation review, software system requirements, issue tracking software survey, systems engineering NPR, and project-related reviews. This report contains a summary of the work performed and the accomplishments in each of these areas.

Detection and Characterization of Ground Displacement Sources from Variational Bayesian Independent Component Analysis of GPS Time Series

Science.gov (United States)

Gualandi, A.; Serpelloni, E.; Belardinelli, M. E.

2014-12-01

A critical point in the analysis of ground displacements time series is the development of data driven methods that allow to discern and characterize the different sources that generate the observed displacements. A widely used multivariate statistical technique is the Principal Component Analysis (PCA), which allows to reduce the dimensionality of the data space maintaining most of the variance of the dataset explained. It reproduces the original data using a limited number of Principal Components, but it also shows some deficiencies. Indeed, PCA does not perform well in finding the solution to the so-called Blind Source Separation (BSS) problem, i.e. in recovering and separating the original sources that generated the observed data. This is mainly due to the assumptions on which PCA relies: it looks for a new Euclidean space where the projected data are uncorrelated. Usually, the uncorrelation condition is not strong enough and it has been proven that the BSS problem can be tackled imposing on the components to be independent. The Independent Component Analysis (ICA) is, in fact, another popular technique adopted to approach this problem, and it can be used in all those fields where PCA is also applied. An ICA approach enables us to explain the time series imposing a fewer number of constraints on the model, and to reveal anomalies in the data such as transient signals. However, the independence condition is not easy to impose, and it is often necessary to introduce some approximations. To work around this problem, we use a variational bayesian ICA (vbICA) method, which models the probability density function (pdf) of each source signal using a mix of Gaussian distributions. This technique allows for more flexibility in the description of the pdf of the sources, giving a more reliable estimate of them. Here we present the application of the vbICA technique to GPS position time series. First, we use vbICA on synthetic data that simulate a seismic cycle

Sandia software guidelines, Volume 4: Configuration management

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

This volume is one in a series of Sandia Software Guidelines for use in producing quality software within Sandia National Laboratories. This volume is based on the IEEE standard and guide for software configuration management. The basic concepts and detailed guidance on implementation of these concepts are discussed for several software project types. Example planning documents for both projects and organizations are included.

A systematic approach for component-based software development

NARCIS (Netherlands)

Guareis de farias, Cléver; van Sinderen, Marten J.; Ferreira Pires, Luis

2000-01-01

Component-based software development enables the construction of software artefacts by assembling prefabricated, configurable and independently evolving building blocks, called software components. This paper presents an approach for the development of component-based software artefacts. This

Why are small software organisations different?

OpenAIRE

Richardson, Ita; Gresse von Wangenheim, Christiane

2007-01-01

peer-reviewed Small software organizations independently financed and organized companies with fewer than 50 employees are fundamental to many national economies' growth. In the US, Brazil, Canada, China, India, Finland, Ireland, Hungary, and many other countries, small companies represent up to 85 percent of all software organizations. However, to persist and grow, small software companies need efficient, effective software engineering solutions.

IMAGE information monitoring and applied graphics software environment. Volume 2. Software description

International Nuclear Information System (INIS)

Hallam, J.W.; Ng, K.B.; Upham, G.L.

1986-09-01

The EPRI Information Monitoring and Applied Graphics Environment (IMAGE) system is designed for 'fast proto-typing' of advanced concepts for computer-aided plant operations tools. It is a flexible software system which can be used for rapidly creating, dynamically driving and evaluating advanced operator aid displays. The software is written to be both host computer and graphic device independent

Spatiotemporal Patterns of Precipitation-Modulated Landslide Deformation From Independent Component Analysis of InSAR Time Series

Science.gov (United States)

Cohen-Waeber, J.; Bürgmann, R.; Chaussard, E.; Giannico, C.; Ferretti, A.

2018-02-01

Long-term landslide deformation is disruptive and costly in urbanized environments. We rely on TerraSAR-X satellite images (2009-2014) and an improved data processing algorithm (SqueeSAR™) to produce an exceptionally dense Interferometric Synthetic Aperture Radar ground deformation time series for the San Francisco East Bay Hills. Independent and principal component analyses of the time series reveal four distinct spatial and temporal surface deformation patterns in the area around Blakemont landslide, which we relate to different geomechanical processes. Two components of time-dependent landslide deformation isolate continuous motion and motion driven by precipitation-modulated pore pressure changes controlled by annual seasonal cycles and multiyear drought conditions. Two components capturing more widespread seasonal deformation separate precipitation-modulated soil swelling from annual cycles that may be related to groundwater level changes and thermal expansion of buildings. High-resolution characterization of landslide response to precipitation is a first step toward improved hazard forecasting.

Software para la Evaluación y Selección de Generadores Independientes. Independent Generator Evaluation and Selection Software

Directory of Open Access Journals (Sweden)

Marcos Alberto de Armas Teyra

2015-04-01

Full Text Available En muchas industrias, edificios, empresas y servicios por razones productivas, emergentes o de confiablidad, es necesario generar energía eléctrica independientemente del Sistema Eléctrico Nacional. En otros casos se necesitan plantas de generación de energía eléctrica que puedan trabajar de forma aislada alimentando un circuito determinado. Para realizar la selección más económica y eficiente de la capacidad a instalar se debe tomar en consideración no sólo el comportamiento del sistema donde se va a insertar la unidad, sino también, las características operacionales del generador ante las fluctuaciones de la carga, sus límites operacionales y la estabilidad resultante. Este trabajo presenta un software que permite realizar la selección más adecuada considerando la curva de capacidad y la estabilidad del generador ante las particularidades del sistema. Con su aplicación es posible reducir los gastos y las pérdidas económicas debidas a una selección inapropiada. Como caso se presenta su aplicación a una planta de una fábrica de envases de alimentos.  In many industries, buildings and services is necessary to employ independent power plants to supply the electric power to a particular system. In other cases, islanded operation is desired due to several specific situations. In order to realize the most efficient, economic and adequate selection of the generator capacity is necessary to consider not only the systems load characteristic, also is necessary to know the limits of capabilities and the resultant stability of the power generator. This paper presents a software that allows to select the adequate generator, expose the operating limits and the resulting stability in fluctuating load condition. With its application is possible to reduce economic losses and the costs due to an impropriated generator selection with an oversized o sub utilized machine. As a case a 2500 kVA power plant is analyzed.

Remote sensing time series analysis for crop monitoring with the SPIRITS software: new functionalities and use examples

Directory of Open Access Journals (Sweden)

Felix eRembold

2015-07-01

Full Text Available Monitoring crop and natural vegetation conditions is highly relevant, particularly in the food insecure areas of the world. Data from remote sensing image time series at high temporal and medium to low spatial resolution can assist this monitoring as they provide key information about vegetation status in near real-time over large areas. The Software for the Processing and Interpretation of Remotely sensed Image Time Series (SPIRITS is a stand-alone flexible analysis environment created to facilitate the processing and analysis of large image time series and ultimately for providing clear information about vegetation status in various graphical formats to crop production analysts and decision makers. In this paper we present the latest functional developments of SPIRITS and we illustrate recent applications. The main new developments include: HDF5 importer, Image re-projection, additional options for temporal Smoothing and Periodicity conversion, computation of a rainfall-based probability index (Standardized Precipitation Index for drought detection and extension of the Graph composer functionalities.In particular,. The examples of operational analyses are taken from several recent agriculture and food security monitoring reports and bulletins. We conclude with considerations on future SPIRITS developments also in view of the data processing requirements imposed by the coming generation of remote sensing products at high spatial and temporal resolution, such as those provided by the Sentinel sensors of the European Copernicus programme.

Visualization of and Software for Omnibus Test Based Change Detected in a Time Series of Polarimetric SAR Data

DEFF Research Database (Denmark)

Nielsen, Allan Aasbjerg; Conradsen, Knut; Skriver, Henning

2017-01-01

Based on an omnibus likelihood ratio test statistic for the equality of several variance-covariance matrices following the complex Wishart distribution and a factorization of this test statistic with associated p-values, change analysis in a time series of multilook polarimetric SAR data...... in the covariance matrix representation is carried out. The omnibus test statistic and its factorization detect if and when change occurs. Using airborne EMISAR and spaceborne RADARSAT-2 data this paper focuses on change detection based on the p-values, on visualization of change at pixel as well as segment level......, and on computer software....

ACTS: from ATLAS software towards a common track reconstruction software

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00349786; The ATLAS collaboration; Salzburger, Andreas; Kiehn, Moritz; Hrdinka, Julia; Calace, Noemi

2017-01-01

Reconstruction of charged particles' trajectories is a crucial task for most particle physics experiments. The high instantaneous luminosity achieved at the LHC leads to a high number of proton-proton collisions per bunch crossing, which has put the track reconstruction software of the LHC experiments through a thorough test. Preserving track reconstruction performance under increasingly difficult experimental conditions, while keeping the usage of computational resources at a reasonable level, is an inherent problem for many HEP experiments. Exploiting concurrent algorithms and using multivariate techniques for track identification are the primary strategies to achieve that goal. Starting from current ATLAS software, the ACTS project aims to encapsulate track reconstruction software into a generic, framework- and experiment-independent software package. It provides a set of high-level algorithms and data structures for performing track reconstruction tasks as well as fast track simulation. The software is de...

Commissioning software tools at the Advanced Photon Source

International Nuclear Information System (INIS)

Emery, L.

1995-01-01

A software tool-oriented approach has been adopted in the commissioning of the Advanced Photon Source (APS) at Argonne National Laboratory, particularly in the commissioning of the Positron Accumulator Ring (PAR). The general philosophy is to decompose a complicated procedure involving measurement, data processing, and control into a series of simpler steps, each accomplished by a generic toolkit program. The implementation is greatly facilitated by adopting the SDDS (self-describing data set protocol), which comes with its own toolkit. The combined toolkit has made accelerator physics measurements easier. For instance, the measurement of the optical functions of the PAR and the beamlines connected to it have been largely automated. Complicated measurements are feasible with a combination of tools running independently

Architecture design in global and model-centric software development

NARCIS (Netherlands)

Heijstek, Werner

2012-01-01

This doctoral dissertation describes a series of empirical investigations into representation, dissemination and coordination of software architecture design in the context of global software development. A particular focus is placed on model-centric and model-driven software development.

A software program for exchanging MR data

DEFF Research Database (Denmark)

Ring, P B; Jensen, J A; Henriksen, O

1993-01-01

of digital MR images of the human brain. Because there was no common data format, software package was developed for data exchange. This article describes the basic features of the developed software. The software package was written in the language of C and was successfully tested on an IBM-6150 UNIX...... workstation. The software is currently being tested on the following series of UNIX workstations: SUN SPARC, IBM RS6000, and HP 9000/700....

Software Reviews: "Pow! Zap! Ker-plunk! The Comic Book Maker" (Pelican Software).

Science.gov (United States)

Porter, Bernajean

1990-01-01

Reviews the newest addition to Pelican's Creative Writing Series of instructional software, which uses the comic book format to provide a unique writing environment for satire, symbolism, sequencing, and combining text and graphics to communicate ideas. (SR)

Graphical Data Analysis on the Circle: Wrap-Around Time Series Plots for (Interrupted) Time Series Designs.

Science.gov (United States)

Rodgers, Joseph Lee; Beasley, William Howard; Schuelke, Matthew

2014-01-01

Many data structures, particularly time series data, are naturally seasonal, cyclical, or otherwise circular. Past graphical methods for time series have focused on linear plots. In this article, we move graphical analysis onto the circle. We focus on 2 particular methods, one old and one new. Rose diagrams are circular histograms and can be produced in several different forms using the RRose software system. In addition, we propose, develop, illustrate, and provide software support for a new circular graphical method, called Wrap-Around Time Series Plots (WATS Plots), which is a graphical method useful to support time series analyses in general but in particular in relation to interrupted time series designs. We illustrate the use of WATS Plots with an interrupted time series design evaluating the effect of the Oklahoma City bombing on birthrates in Oklahoma County during the 10 years surrounding the bombing of the Murrah Building in Oklahoma City. We compare WATS Plots with linear time series representations and overlay them with smoothing and error bands. Each method is shown to have advantages in relation to the other; in our example, the WATS Plots more clearly show the existence and effect size of the fertility differential.

Software Power Metric Model: An Implementation | Akwukwuma ...

African Journals Online (AJOL)

... and the execution time (TIME) in each case was recorded. We then obtain the application functions point count. Our result shows that the proposed metric is computable, consistent in its use of unit, and is programming language independent. Keywords: Software attributes, Software power, measurement, Software metric, ...

Software product quality measurement

OpenAIRE

Godliauskas, Eimantas

2016-01-01

This paper analyses Ruby product quality measures, suggesting three new measures for Ruby product quality measurement tool Rubocop to measure Ruby product quality characteristics defined in ISO 2502n standard series. This paper consists of four main chapters. The first chapter gives a brief view of software product quality and software product quality measurement. The second chapter analyses object oriented quality measures. The third chapter gives a brief view of the most popular Ruby qualit...

Quality Control Procedure Based on Partitioning of NMR Time Series

Directory of Open Access Journals (Sweden)

Michał Staniszewski

2018-03-01

Full Text Available The quality of the magnetic resonance spectroscopy (MRS depends on the stability of magnetic resonance (MR system performance and optimal hardware functioning, which ensure adequate levels of signal-to-noise ratios (SNR as well as good spectral resolution and minimal artifacts in the spectral data. MRS quality control (QC protocols and methodologies are based on phantom measurements that are repeated regularly. In this work, a signal partitioning algorithm based on a dynamic programming (DP method for QC assessment of the spectral data is described. The proposed algorithm allows detection of the change points—the abrupt variations in the time series data. The proposed QC method was tested using the simulated and real phantom data. Simulated data were randomly generated time series distorted by white noise. The real data were taken from the phantom quality control studies of the MRS scanner collected for four and a half years and analyzed by LCModel software. Along with the proposed algorithm, performance of various literature methods was evaluated for the predefined number of change points based on the error values calculated by subtracting the mean values calculated for the periods between the change-points from the original data points. The time series were checked using external software, a set of external methods and the proposed tool, and the obtained results were comparable. The application of dynamic programming in the analysis of the phantom MRS data is a novel approach to QC. The obtained results confirm that the presented change-point-detection tool can be used either for independent analysis of MRS time series (or any other or as a part of quality control.

HAZARD ANALYSIS SOFTWARE

International Nuclear Information System (INIS)

Sommer, S; Tinh Tran, T.

2008-01-01

Washington Safety Management Solutions, LLC developed web-based software to improve the efficiency and consistency of hazard identification and analysis, control selection and classification, and to standardize analysis reporting at Savannah River Site. In the new nuclear age, information technology provides methods to improve the efficiency of the documented safety analysis development process which includes hazard analysis activities. This software provides a web interface that interacts with a relational database to support analysis, record data, and to ensure reporting consistency. A team of subject matter experts participated in a series of meetings to review the associated processes and procedures for requirements and standard practices. Through these meetings, a set of software requirements were developed and compiled into a requirements traceability matrix from which software could be developed. The software was tested to ensure compliance with the requirements. Training was provided to the hazard analysis leads. Hazard analysis teams using the software have verified its operability. The software has been classified as NQA-1, Level D, as it supports the analysis team but does not perform the analysis. The software can be transported to other sites with alternate risk schemes. The software is being used to support the development of 14 hazard analyses. User responses have been positive with a number of suggestions for improvement which are being incorporated as time permits. The software has enforced a uniform implementation of the site procedures. The software has significantly improved the efficiency and standardization of the hazard analysis process

Using neural networks in software repositories

Science.gov (United States)

Eichmann, David (Editor); Srinivas, Kankanahalli; Boetticher, G.

1992-01-01

The first topic is an exploration of the use of neural network techniques to improve the effectiveness of retrieval in software repositories. The second topic relates to a series of experiments conducted to evaluate the feasibility of using adaptive neural networks as a means of deriving (or more specifically, learning) measures on software. Taken together, these two efforts illuminate a very promising mechanism supporting software infrastructures - one based upon a flexible and responsive technology.

CauseMap: fast inference of causality from complex time series.

Science.gov (United States)

Maher, M Cyrus; Hernandez, Ryan D

2015-01-01

high-performance programming language designed for facile technical computing. Our software package, CauseMap, is platform-independent and freely available as an official Julia package. Conclusions. CauseMap is an efficient implementation of a state-of-the-art algorithm for detecting causality from time series data. We believe this tool will be a valuable resource for biomedical research and personalized medicine.

CauseMap: fast inference of causality from complex time series

Directory of Open Access Journals (Sweden)

M. Cyrus Maher

2015-03-01

CCM in Julia, a high-performance programming language designed for facile technical computing. Our software package, CauseMap, is platform-independent and freely available as an official Julia package.Conclusions. CauseMap is an efficient implementation of a state-of-the-art algorithm for detecting causality from time series data. We believe this tool will be a valuable resource for biomedical research and personalized medicine.

Testing the assumption in ergonomics software that overall shoulder strength can be accurately calculated by treating orthopedic axes as independent.

Science.gov (United States)

Hodder, Joanne N; La Delfa, Nicholas J; Potvin, Jim R

2016-08-01

To predict shoulder strength, most current ergonomics software assume independence of the strengths about each of the orthopedic axes. Using this independent axis approach (IAA), the shoulder can be predicted to have strengths as high as the resultant of the maximum moment about any two or three axes. We propose that shoulder strength is not independent between axes, and propose an approach that calculates the weighted average (WAA) between the strengths of the axes involved in the demand. Fifteen female participants performed maximum isometric shoulder exertions with their right arm placed in a rigid adjustable brace affixed to a tri-axial load cell. Maximum exertions were performed in 24 directions, including four primary directions, horizontal flexion-extension, abduction-adduction, and at 15° increments in between those axes. Moments were computed and comparisons made between the experimentally collected strengths and those predicted by the IAA and WAA methods. The IAA over-predicted strength in 14 of 20 non-primary exertions directions, while the WAA underpredicted strength in only 2 of these directions. Therefore, it is not valid to assume that shoulder axes are independent when predicting shoulder strengths between two orthopedic axes, and the WAA is an improvement over current methods for the posture tested. Copyright © 2015 Elsevier Ltd. All rights reserved.

Statistical reliability assessment of software-based systems

International Nuclear Information System (INIS)

Korhonen, J.; Pulkkinen, U.; Haapanen, P.

1997-01-01

Plant vendors nowadays propose software-based systems even for the most critical safety functions. The reliability estimation of safety critical software-based systems is difficult since the conventional modeling techniques do not necessarily apply to the analysis of these systems, and the quantification seems to be impossible. Due to lack of operational experience and due to the nature of software faults, the conventional reliability estimation methods can not be applied. New methods are therefore needed for the safety assessment of software-based systems. In the research project Programmable automation systems in nuclear power plants (OHA), financed together by the Finnish Centre for Radiation and Nuclear Safety (STUK), the Ministry of Trade and Industry and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. This volume in the OHA-report series deals with the statistical reliability assessment of software based systems on the basis of dynamic test results and qualitative evidence from the system design process. Other reports to be published later on in OHA-report series will handle the diversity requirements in safety critical software-based systems, generation of test data from operational profiles and handling of programmable automation in plant PSA-studies. (orig.) (25 refs.)

Arquitectura orientada a servicios para software de apoyo para el proceso personal de software A service oriented architecture for the implementation of the personal software process

Directory of Open Access Journals (Sweden)

Erick Salinas

2011-06-01

Full Text Available El presente trabajo describe una arquitectura orientada a servicios para un software que tiene como objetivo facilitar la implementación de un Proceso Personal de Software en un equipo de desarrollo u organización. Entre las características que posee este software y que son relevantes de mencionar están las de entregar extensibilidad e independencia, esto se ve reflejado en la facilidad para agregar nuevas herramientas al proceso de desarrollo de software integradas al Proceso Personal de Software con un máximo de independencia de sistemas operativos y lenguajes de programación. El software implementado realiza la recolección de los datos necesarios para el Proceso Personal de Software casi completamente automática, considerando que el administrador solamente clasifica los errores que pueden ocurrir cuando se utiliza algún lenguaje de programación en particular, entre otras pequeñas tareas. Esta facilidad de uso hace que la implementación del Proceso Personal de Software se realice exitosamente con un bajo esfuerzo requerido por los integrantes del equipo de desarrollo.This work describes a service oriented architecture of a software application that facilitates the implementation of the Personal Software Process by a development team or an organization. Some of the characteristics of this software and which are important to mention are extensibility and technical environment independence. These characteristics facilitate the process of adding new tools to the software development process integrating them to the Personal Software Process independently of the operating systems and programming languages being used. The implemented software undertakes the data collection necessary to the Personal Software Process almost automatically, since the administrator must only classify the errors that may occur when a particular programming language is used, among other small tasks. This ease of use approach helps to make the implementation of

Sandia software guidelines: Volume 5, Tools, techniques, and methodologies

Energy Technology Data Exchange (ETDEWEB)

1989-07-01

This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. This volume describes software tools and methodologies available to Sandia personnel for the development of software, and outlines techniques that have proven useful within the Laboratories and elsewhere. References and evaluations by Sandia personnel are included. 6 figs.

Effectiveness of Multivariate Time Series Classification Using Shapelets

Directory of Open Access Journals (Sweden)

A. P. Karpenko

2015-01-01

Full Text Available Typically, time series classifiers require signal pre-processing (filtering signals from noise and artifact removal, etc., enhancement of signal features (amplitude, frequency, spectrum, etc., classification of signal features in space using the classical techniques and classification algorithms of multivariate data. We consider a method of classifying time series, which does not require enhancement of the signal features. The method uses the shapelets of time series (time series shapelets i.e. small fragments of this series, which reflect properties of one of its classes most of all.Despite the significant number of publications on the theory and shapelet applications for classification of time series, the task to evaluate the effectiveness of this technique remains relevant. An objective of this publication is to study the effectiveness of a number of modifications of the original shapelet method as applied to the multivariate series classification that is a littlestudied problem. The paper presents the problem statement of multivariate time series classification using the shapelets and describes the shapelet–based basic method of binary classification, as well as various generalizations and proposed modification of the method. It also offers the software that implements a modified method and results of computational experiments confirming the effectiveness of the algorithmic and software solutions.The paper shows that the modified method and the software to use it allow us to reach the classification accuracy of about 85%, at best. The shapelet search time increases in proportion to input data dimension.

Software for 3D diagnostic image reconstruction and analysis

International Nuclear Information System (INIS)

Taton, G.; Rokita, E.; Sierzega, M.; Klek, S.; Kulig, J.; Urbanik, A.

2005-01-01

Recent advances in computer technologies have opened new frontiers in medical diagnostics. Interesting possibilities are the use of three-dimensional (3D) imaging and the combination of images from different modalities. Software prepared in our laboratories devoted to 3D image reconstruction and analysis from computed tomography and ultrasonography is presented. In developing our software it was assumed that it should be applicable in standard medical practice, i.e. it should work effectively with a PC. An additional feature is the possibility of combining 3D images from different modalities. The reconstruction and data processing can be conducted using a standard PC, so low investment costs result in the introduction of advanced and useful diagnostic possibilities. The program was tested on a PC using DICOM data from computed tomography and TIFF files obtained from a 3D ultrasound system. The results of the anthropomorphic phantom and patient data were taken into consideration. A new approach was used to achieve spatial correlation of two independently obtained 3D images. The method relies on the use of four pairs of markers within the regions under consideration. The user selects the markers manually and the computer calculates the transformations necessary for coupling the images. The main software feature is the possibility of 3D image reconstruction from a series of two-dimensional (2D) images. The reconstructed 3D image can be: (1) viewed with the most popular methods of 3D image viewing, (2) filtered and processed to improve image quality, (3) analyzed quantitatively (geometrical measurements), and (4) coupled with another, independently acquired 3D image. The reconstructed and processed 3D image can be stored at every stage of image processing. The overall software performance was good considering the relatively low costs of the hardware used and the huge data sets processed. The program can be freely used and tested (source code and program available at

Developing software for safety-critical applications

International Nuclear Information System (INIS)

Chudleigh, M.

1989-01-01

The effective implementation of many safety-critical systems involves microprocessors running software which needs to be of very high integrity. This article describes some of the problems of producing such software and the place of software within the total system. A development strategy is proposed based on three principles: the goal of defect-free development, the use of mathematical formalism, and the use of an independent team for testing. (author)

Software Engineering Education: Some Important Dimensions

Science.gov (United States)

Mishra, Alok; Cagiltay, Nergiz Ercil; Kilic, Ozkan

2007-01-01

Software engineering education has been emerging as an independent and mature discipline. Accordingly, various studies are being done to provide guidelines for curriculum design. The main focus of these guidelines is around core and foundation courses. This paper summarizes the current problems of software engineering education programs. It also…

Software engineering turning theory into practice

CERN Document Server

Jones, Robert

1996-01-01

The term 'Software Engineering' was coined in the mid 1960s, it is said, as a challenge to the software community to start rationalising the software production process. Software engineering is a very young discipline and this challenge still eludes LHC demands software production on a scale far beyond that previously addressed in HEP and we are relying on software engineering to allow a significant number of people address this problem collectively. This series of lectures presents the basics of software engineering from the developer's point of view. The aim is to show how individual developers can improve the quality of the software they produce while avoiding the conflict between the creative process of designing software and the organisational needs of large projects.The Laser Interferometer Gravitanional Wave Observatory (LIGO) is being constructed with a goal to detect these waves and then to use them as a new tool to explore and study The sources of gravitanional waves and techniques for detection wil...

Software Engineering Principles for Courseware Development.

Science.gov (United States)

Magel, Kenneth

1980-01-01

Courseware (computer based curriculum materials) development should follow the lessons learned by software engineers. The most important of 28 principles of software development presented here include a stress on human readability, the importance of early planning and analysis, the need for independent evaluation, and the need to be flexible.…

Collection Of Software For Computer Graphics

Science.gov (United States)

Hibbard, Eric A.; Makatura, George

1990-01-01

Ames Research Graphics System (ARCGRAPH) collection of software libraries and software utilities assisting researchers in generating, manipulating, and visualizing graphical data. Defines metafile format containing device-independent graphical data. File format used with various computer-graphics-manipulation and -animation software packages at Ames, including SURF (COSMIC Program ARC-12381) and GAS (COSMIC Program ARC-12379). Consists of two-stage "pipeline" used to put out graphical primitives. ARCGRAPH libraries developed on VAX computer running VMS.

An architecture for device independent interfacing

International Nuclear Information System (INIS)

Pace, D.M.

1990-01-01

Achieving device independence for software applications is required for all but a small number of critical real time applications. Device independence is achieved by establishing protocols and building protocol interpreters for the specific devices. Data structures containing pointers to functions provide a flexible architecture for implementing protocol translation. 3 refs., 5 figs

Secure Software Configuration Management Processes for nuclear safety software development environment

International Nuclear Information System (INIS)

Chou, I.-Hsin

2011-01-01

Highlights: → The proposed method emphasizes platform-independent security processes. → A hybrid process based on the nuclear SCM and security regulations is proposed. → Detailed descriptions and Process Flow Diagram are useful for software developers. - Abstract: The main difference between nuclear and generic software is that the risk factor is infinitely greater in nuclear software - if there is a malfunction in the safety system, it can result in significant economic loss, physical damage or threat to human life. However, secure software development environment have often been ignored in the nuclear industry. In response to the terrorist attacks on September 11, 2001, the US Nuclear Regulatory Commission (USNRC) revised the Regulatory Guide (RG 1.152-2006) 'Criteria for use of computers in safety systems of nuclear power plants' to provide specific security guidance throughout the software development life cycle. Software Configuration Management (SCM) is an essential discipline in the software development environment. SCM involves identifying configuration items, controlling changes to those items, and maintaining integrity and traceability of them. For securing the nuclear safety software, this paper proposes a Secure SCM Processes (S 2 CMP) which infuses regulatory security requirements into proposed SCM processes. Furthermore, a Process Flow Diagram (PFD) is adopted to describe S 2 CMP, which is intended to enhance the communication between regulators and developers.

An independent monitor unit calculation by commercial software as a part of a radiotherapy treatment planning system quality control

International Nuclear Information System (INIS)

Nechvil, K.; Mynarik, J.

2014-01-01

For the independent calculation of the monitored unit (MU) the commercial software RadCalc (Lifeline Software Inc., Tyler TX) was used as the choice of some available similar programs. The program was configured and used to verify the doses calculated by commercially accessible planning system Eclipse version 8.6.17 (Varian Medical System Inc., Palo Alto). This system is being used during the clinical running for the creation of the treatment plans. The results of each plan were compared to the dose phantom measurements by the ionization chamber at the same point in which the calculation were done (Eclipse, RadCalc) - in the izocentre. TPS is configured by the beam data (PDD and OAR). Those beam data were exported and afterwards the same data were imported to the program RadCalc. The consistent and independent data between TPS and RadCalc were gained by this process. The reference conditions were set the identical in RadCalc as in TPS, so the consistency between TPS and RadCalc output factors has been achieved (Collimator Scatter Factor: Sc, Phantom Scatter Factor: Sp). Those output factors were also measured by the ionizing chamber in the water phantom and compared with the TPS. Based on the clinical data of the response to the doses, ICRU recommends ensuring the ability of dosimetric systems to deliver the doses with accuracy of at least 5%. Many factors, such as layout of anatomic structures, positioning of a patient, factors related to an accelerator (a dose calibration and mechanic parameters) cause random and systematic failures in a dose delivery. The source of some problems can be also caused by the system databases and relating information transfer; and the TPS containing besides other things other dose calculation algorithms. (authors)

ACTS: from ATLAS software towards a common track reconstruction software

Science.gov (United States)

Gumpert, C.; Salzburger, A.; Kiehn, M.; Hrdinka, J.; Calace, N.; ATLAS Collaboration

2017-10-01

Reconstruction of charged particles’ trajectories is a crucial task for most particle physics experiments. The high instantaneous luminosity achieved at the LHC leads to a high number of proton-proton collisions per bunch crossing, which has put the track reconstruction software of the LHC experiments through a thorough test. Preserving track reconstruction performance under increasingly difficult experimental conditions, while keeping the usage of computational resources at a reasonable level, is an inherent problem for many HEP experiments. Exploiting concurrent algorithms and using multivariate techniques for track identification are the primary strategies to achieve that goal. Starting from current ATLAS software, the ACTS project aims to encapsulate track reconstruction software into a generic, framework- and experiment-independent software package. It provides a set of high-level algorithms and data structures for performing track reconstruction tasks as well as fast track simulation. The software is developed with special emphasis on thread-safety to support parallel execution of the code and data structures are optimised for vectorisation to speed up linear algebra operations. The implementation is agnostic to the details of the detection technologies and magnetic field configuration which makes it applicable to many different experiments.

Independent verification of monitor unit calculation for radiation treatment planning system.

Science.gov (United States)

Chen, Li; Chen, Li-Xin; Huang, Shao-Min; Sun, Wen-Zhao; Sun, Hong-Qiang; Deng, Xiao-Wu

2010-02-01

To ensure the accuracy of dose calculation for radiation treatment plans is an important part of quality assurance (QA) procedures for radiotherapy. This study evaluated the Monitor Units (MU) calculation accuracy of a third-party QA software and a 3-dimensional treatment planning system (3D TPS), to investigate the feasibility and reliability of independent verification for radiation treatment planning. Test plans in a homogenous phantom were designed with 3-D TPS, according to the International Atomic Energy Agency (IAEA) Technical Report No. 430, including open, blocked, wedge, and multileaf collimator (MLC) fields. Test plans were delivered and measured in the phantom. The delivered doses were input to the QA software and the independent calculated MUs were compared with delivery. All test plans were verified with independent calculation and phantom measurements separately, and the differences of the two kinds of verification were then compared. The deviation of the independent calculation to the measurements was (0.1 +/- 0.9)%, the biggest difference fell onto the plans that used block and wedge fields (2.0%). The mean MU difference between the TPS and the QA software was (0.6 +/- 1.0)%, ranging from -0.8% to 2.8%. The deviation in dose of the TPS calculation compared to the measurements was (-0.2 +/- 1.7)%, ranging from -3.9% to 2.9%. MU accuracy of the third-party QA software is clinically acceptable. Similar results were achieved with the independent calculations and the phantom measurements for all test plans. The tested independent calculation software can be used as an efficient tool for TPS plan verification.

Gambling kick or content motivation - what is really initialized by the introduction of software into medical biometry lessons???

Directory of Open Access Journals (Sweden)

Krummenauer, Frank

2005-08-01

Full Text Available Bachground: Teaching statistics to members of non-mathematical disciplines becomes increasingly based on the involvement of interactive learning software. The latter is expected to both increase understanding and motivation and thereby as well studential acceptance. The teaching model implemented at the Medical Biometry Department in Mainz will be used to consider the value of introducing an interactive software like SPSS® into biometry lessons by means of studential evaluations.Methods: After an introductory lecture series, the participants of the Medical Biometry (formerly "Biomathematics" practical courses are requested to solve real data exercises by means of the software SPSS®, where each lessons aims to the derivation of a result synopsis summarizing the results of the performed statistical analyses. In summer 2002 the students of this course were asked to fill out a standardized teaching quality assessment questionnaire on the acceptance of the previous lecture series, the practical course lessons and the involvement of the software.Results: Between the 7 parallel courses the fraction of students reporting "good management with SPSS" varies between 43% and 88% (pooled estimate 58%, but among these students only 30% report a good / very good understanding of the lessons' context and only 15% a good / very good learning effect. Among students with "problems in SPSS management" these fractions both turned out 13%. Among the students with "good management with SPSS", however, 70% considered the understanding during the lecture series as good / very good, 73% reported a good / very good learning effect for the lectures; among the other students both fractions were 13%. These subgrupus only differed significantly for the questionnaire dimension "content motivation" (Likelihood Ratio p<0.001 after correction for teacher effects. Neither the lessons' structure (p=0.362, their relation to the introductory lecture series (p=0.165 nor the teachers

Integrated modeling of software cost and quality

International Nuclear Information System (INIS)

Rone, K.Y.; Olson, K.M.

1994-01-01

In modeling the cost and quality of software systems, the relationship between cost and quality must be considered. This explicit relationship is dictated by the criticality of the software being developed. The balance between cost and quality is a viable software engineering trade-off throughout the life cycle. Therefore, the ability to accurately estimate the cost and quality of software systems is essential to providing reliable software on time and within budget. Software cost models relate the product error rate to the percent of the project labor that is required for independent verification and validation. The criticality of the software determines which cost model is used to estimate the labor required to develop the software. Software quality models yield an expected error discovery rate based on the software size, criticality, software development environment, and the level of competence of the project and the developers with respect to the processes being employed

ImagePy: an open-source, Python-based and platform-independent software package for boimage analysis.

Science.gov (United States)

Wang, Anliang; Yan, Xiaolong; Wei, Zhijun

2018-04-27

This note presents the design of a scalable software package named ImagePy for analysing biological images. Our contribution is concentrated on facilitating extensibility and interoperability of the software through decoupling the data model from the user interface. Especially with assistance from the Python ecosystem, this software framework makes modern computer algorithms easier to be applied in bioimage analysis. ImagePy is free and open source software, with documentation and code available at https://github.com/Image-Py/imagepy under the BSD license. It has been tested on the Windows, Mac and Linux operating systems. wzjdlut@dlut.edu.cn or yxdragon@imagepy.org.

Un framework para el despliegue y evaluación de procesos software

OpenAIRE

Ruiz-Rube, Iván

2014-01-01

La Ingeniería de Procesos Software promueve la producción sistemática de software mediante el seguimiento de una serie de procesos bien definidos. Una gestión integral de dichos procesos implica el desarrollo de una serie de actividades como son el diseño de los modelos de procesos, la verificación, la validación, el despliegue y la posterior evaluación. El consorcio OMG publicó el estándar Software Process Engineering Metamodel (SPEM), un lenguaje destinado a facilitar y potenciar el entendi...

CMS software deployment on OSG

International Nuclear Information System (INIS)

Kim, B; Avery, P; Thomas, M; Wuerthwein, F

2008-01-01

A set of software deployment tools has been developed for the installation, verification, and removal of a CMS software release. The tools that are mainly targeted for the deployment on the OSG have the features of instant release deployment, corrective resubmission of the initial installation job, and an independent web-based deployment portal with Grid security infrastructure login mechanism. We have been deploying over 500 installations and found the tools are reliable and adaptable to cope with problems with changes in the Grid computing environment and the software releases. We present the design of the tools, statistics that we gathered during the operation of the tools, and our experience with the CMS software deployment on the OSG Grid computing environment

CMS software deployment on OSG

Energy Technology Data Exchange (ETDEWEB)

Kim, B; Avery, P [University of Florida, Gainesville, FL 32611 (United States); Thomas, M [California Institute of Technology, Pasadena, CA 91125 (United States); Wuerthwein, F [University of California at San Diego, La Jolla, CA 92093 (United States)], E-mail: bockjoo@phys.ufl.edu, E-mail: thomas@hep.caltech.edu, E-mail: avery@phys.ufl.edu, E-mail: fkw@fnal.gov

2008-07-15

A set of software deployment tools has been developed for the installation, verification, and removal of a CMS software release. The tools that are mainly targeted for the deployment on the OSG have the features of instant release deployment, corrective resubmission of the initial installation job, and an independent web-based deployment portal with Grid security infrastructure login mechanism. We have been deploying over 500 installations and found the tools are reliable and adaptable to cope with problems with changes in the Grid computing environment and the software releases. We present the design of the tools, statistics that we gathered during the operation of the tools, and our experience with the CMS software deployment on the OSG Grid computing environment.

Technical Evaluation Report 37: Assistive Software for Disabled Learners

Directory of Open Access Journals (Sweden)

Jon Baggaley

2004-11-01

Full Text Available Previous reports in this series (#32 and 36 have discussed online software features of value to disabled learners in distance education. The current report evaluates four specific assistive software products with useful features for visually and hearing impaired learners: ATutor, ACollab, Natural Voice, and Just Vanilla. The evaluative criteria discussed include the purpose, uses, costs, and features of each software product, all considered primarily from the accessibility perspective.

Knowledge-Based Software Management

International Nuclear Information System (INIS)

Sally Schaffner; Matthew Bickley; Brian Bevins; Leon Clancy; Karen White

2003-01-01

Management of software in a dynamic environment such as is found at Jefferson Lab can be a daunting task. Software development tasks are distributed over a wide range of people with varying skill levels. The machine configuration is constantly changing requiring upgrades to software at both the hardware control level and the operator control level. In order to obtain high quality support from vendor service agreements, which is vital to maintaining 24/7 operations, hardware and software must be kept at industry's current levels. This means that periodic upgrades independent of machine configuration changes must take place. It is often difficult to identify and organize the information needed to guide the process of development, upgrades and enhancements. Dependencies between support software and applications need to be consistently identified to prevent introducing errors during upgrades and to allow adequate testing to be planned and performed. Developers also need access to information regarding compilers, make files and organized distribution directories. This paper describes a system under development at Jefferson Lab which will provide software developers and managers this type of information in a timely user-friendly fashion. The current status and future plans for the system will be detailed

A SOFTWARE TOOL TO COMPARE MEASURED AND SIMULATED BUILDING ENERGY PERFORMANCE DATA

Energy Technology Data Exchange (ETDEWEB)

Maile, Tobias; Bazjanac, Vladimir; O' Donnell, James; Garr, Matthew

2011-11-01

Building energy performance is often inadequate when compared to design goals. To link design goals to actual operation one can compare measured with simulated energy performance data. Our previously developed comparison approach is the Energy Performance Comparison Methodology (EPCM), which enables the identification of performance problems based on a comparison of measured and simulated performance data. In context of this method, we developed a software tool that provides graphing and data processing capabilities of the two performance data sets. The software tool called SEE IT (Stanford Energy Efficiency Information Tool) eliminates the need for manual generation of data plots and data reformatting. SEE IT makes the generation of time series, scatter and carpet plots independent of the source of data (measured or simulated) and provides a valuable tool for comparing measurements with simulation results. SEE IT also allows assigning data points on a predefined building object hierarchy and supports different versions of simulated performance data. This paper briefly introduces the EPCM, describes the SEE IT tool and illustrates its use in the context of a building case study.

Towards a typification of software ecosystems

DEFF Research Database (Denmark)

Knodel, Jens; Manikas, Konstantinos

2015-01-01

Classical software engineering has been traditionally dominated by stand-alone development organizations and collaborations be- tween contractors, integrators and suppliers. The notion of software ecosystems has been established as a new kind of software engineer- ing paradigm in the last decade....... In its essence it proposes participative engineering across independent development organizations. This short paper reviews the current state-of-the-art and presents a typification of successful software ecosystems. We further discuss key characteristic of the ecosystem types and present a set of example...... cases. The characterization reviews and consolidates existing research and discusses variations within the key building block of a software ecosystem. It further enables sharpening the borders of what an ecosystem is (and what not) and how the individual types can be differentiated. Thus, this paper...

The GOLM-database standard- a framework for time-series data management based on free software

Science.gov (United States)

Eichler, M.; Francke, T.; Kneis, D.; Reusser, D.

2009-04-01

Monitoring and modelling projects usually involve time series data originating from different sources. Often, file formats, temporal resolution and meta-data documentation rarely adhere to a common standard. As a result, much effort is spent on converting, harmonizing, merging, checking, resampling and reformatting these data. Moreover, in work groups or during the course of time, these tasks tend to be carried out redundantly and repeatedly, especially when new data becomes available. The resulting duplication of data in various formats strains additional ressources. We propose a database structure and complementary scripts for facilitating these tasks. The GOLM- (General Observation and Location Management) framework allows for import and storage of time series data of different type while assisting in meta-data documentation, plausibility checking and harmonization. The imported data can be visually inspected and its coverage among locations and variables may be visualized. Supplementing scripts provide options for data export for selected stations and variables and resampling of the data to the desired temporal resolution. These tools can, for example, be used for generating model input files or reports. Since GOLM fully supports network access, the system can be used efficiently by distributed working groups accessing the same data over the internet. GOLM's database structure and the complementary scripts can easily be customized to specific needs. Any involved software such as MySQL, R, PHP, OpenOffice as well as the scripts for building and using the data base, including documentation, are free for download. GOLM was developed out of the practical requirements of the OPAQUE-project. It has been tested and further refined in the ERANET-CRUE and SESAM projects, all of which used GOLM to manage meteorological, hydrological and/or water quality data.

ALMA software architecture

Science.gov (United States)

Schwarz, Joseph; Raffi, Gianni

2002-12-01

The Atacama Large Millimeter Array (ALMA) is a joint project involving astronomical organizations in Europe and North America. ALMA will consist of at least 64 12-meter antennas operating in the millimeter and sub-millimeter range. It will be located at an altitude of about 5000m in the Chilean Atacama desert. The primary challenge to the development of the software architecture is the fact that both its development and runtime environments will be distributed. Groups at different institutes will develop the key elements such as Proposal Preparation tools, Instrument operation, On-line calibration and reduction, and Archiving. The Proposal Preparation software will be used primarily at scientists' home institutions (or on their laptops), while Instrument Operations will execute on a set of networked computers at the ALMA Operations Support Facility. The ALMA Science Archive, itself to be replicated at several sites, will serve astronomers worldwide. Building upon the existing ALMA Common Software (ACS), the system architects will prepare a robust framework that will use XML-encoded entity objects to provide an effective solution to the persistence needs of this system, while remaining largely independent of any underlying DBMS technology. Independence of distributed subsystems will be facilitated by an XML- and CORBA-based pass-by-value mechanism for exchange of objects. Proof of concept (as well as a guide to subsystem developers) will come from a prototype whose details will be presented.

Review of Bruce A reactor regulating system software

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

Each of the four reactor units at the Ontario Hydro Bruce A Nuclear Generating Station is controlled by the Reactor Regulating System (RRS) software running on digital computers. This research report presents an assessment of the quality and reliability of the RRS software based on a review of the RRS design documentation, an analysis of certain significant Event Reports (SERs), and an examination of selected software changes. We found that the RRS software requirements (i.e., what the software should do) were never clearly documented, and that design documents, which should describe how the requirements are implemented, are incomplete and inaccurate. Some RRS-related SERs (i.e., reports on unexpected incidents relating to the reactor control) implied that there were faults in the RRS, or that RRS changes should be made to help prevent certain unexpected events. The follow-up investigations were generally poorly documented, and so it could not usually be determined that problems were properly resolved. The Bruce A software change control procedures require improvement. For the software changes examined, there was insufficient evidence provided by Ontario Hydro that the required procedures regarding change approval, independent review, documentation updates, and testing were followed. Ontario Hydro relies on the expertise of their technical staff to modify the RRS software correctly; they have confidence in the software code itself, even if the documentation is not up-to-date. Ontario Hydro did not produce the documentation required for an independent formal assessment of the reliability of the RRS. (author). 37 refs., 3 figs.

Review of Bruce A reactor regulating system software

International Nuclear Information System (INIS)

1995-12-01

Each of the four reactor units at the Ontario Hydro Bruce A Nuclear Generating Station is controlled by the Reactor Regulating System (RRS) software running on digital computers. This research report presents an assessment of the quality and reliability of the RRS software based on a review of the RRS design documentation, an analysis of certain significant Event Reports (SERs), and an examination of selected software changes. We found that the RRS software requirements (i.e., what the software should do) were never clearly documented, and that design documents, which should describe how the requirements are implemented, are incomplete and inaccurate. Some RRS-related SERs (i.e., reports on unexpected incidents relating to the reactor control) implied that there were faults in the RRS, or that RRS changes should be made to help prevent certain unexpected events. The follow-up investigations were generally poorly documented, and so it could not usually be determined that problems were properly resolved. The Bruce A software change control procedures require improvement. For the software changes examined, there was insufficient evidence provided by Ontario Hydro that the required procedures regarding change approval, independent review, documentation updates, and testing were followed. Ontario Hydro relies on the expertise of their technical staff to modify the RRS software correctly; they have confidence in the software code itself, even if the documentation is not up-to-date. Ontario Hydro did not produce the documentation required for an independent formal assessment of the reliability of the RRS. (author). 37 refs., 3 figs

Licensing process for safety-critical software-based systems

Energy Technology Data Exchange (ETDEWEB)

Haapanen, P. [VTT Automation, Espoo (Finland); Korhonen, J. [VTT Electronics, Espoo (Finland); Pulkkinen, U. [VTT Automation, Espoo (Finland)

2000-12-01

System vendors nowadays propose software-based technology even for the most critical safety functions in nuclear power plants. Due to the nature of software faults and the way they cause system failures new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)', financed together by the Radiation and Nuclear Safety Authority (STUK), the Ministry of Trade and Industry (KTM) and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. As a part of the OHA-work a reference model for the licensing process for software-based safety automation systems is defined. The licensing process is defined as the set of interrelated activities whose purpose is to produce and assess evidence concerning the safety and reliability of the system/application to be licensed and to make the decision about the granting the construction and operation permissions based on this evidence. The parties of the licensing process are the authority, the licensee (the utility company), system vendors and their subcontractors and possible external independent assessors. The responsibility about the production of the evidence in first place lies at the licensee who in most cases rests heavily on the vendor expertise. The evaluation and gauging of the evidence is carried out by the authority (possibly using external experts), who also can acquire additional evidence by using their own (independent) methods and tools. Central issue in the licensing process is to combine the quality evidence about the system development process with the information acquired through tests, analyses and operational experience. The purpose of the licensing process described in this report is to act as a reference model both for the authority and the licensee when planning the licensing of individual applications

Licensing process for safety-critical software-based systems

International Nuclear Information System (INIS)

Haapanen, P.; Korhonen, J.; Pulkkinen, U.

2000-12-01

System vendors nowadays propose software-based technology even for the most critical safety functions in nuclear power plants. Due to the nature of software faults and the way they cause system failures new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)', financed together by the Radiation and Nuclear Safety Authority (STUK), the Ministry of Trade and Industry (KTM) and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. As a part of the OHA-work a reference model for the licensing process for software-based safety automation systems is defined. The licensing process is defined as the set of interrelated activities whose purpose is to produce and assess evidence concerning the safety and reliability of the system/application to be licensed and to make the decision about the granting the construction and operation permissions based on this evidence. The parties of the licensing process are the authority, the licensee (the utility company), system vendors and their subcontractors and possible external independent assessors. The responsibility about the production of the evidence in first place lies at the licensee who in most cases rests heavily on the vendor expertise. The evaluation and gauging of the evidence is carried out by the authority (possibly using external experts), who also can acquire additional evidence by using their own (independent) methods and tools. Central issue in the licensing process is to combine the quality evidence about the system development process with the information acquired through tests, analyses and operational experience. The purpose of the licensing process described in this report is to act as a reference model both for the authority and the licensee when planning the licensing of individual applications. Many of the

ORNL's DCAL software package

International Nuclear Information System (INIS)

Eckerman, K.F.

2007-01-01

Oak Ridge National Laboratory has released its Dose and Risk Calculation software, DCAL. DCAL, developed with the support of the U.S. Environmental Protection Agency, consists of a series of computational modules, driven in either an interactive or a batch mode for computation of dose and risk coefficients from intakes of radionuclides or exposure to radionuclides in environmental media. The software package includes extensive libraries of biokinetic and dosimetric data that represent the current state of the art. The software has unique capability for addressing intakes of radionuclides by non-adults. DCAL runs as 32-bit extended DOS and console applications under Windows 98/NT/2000/XP. It is intended for users familiar with the basic elements of computational radiation dosimetry. Components of DCAL have been used to prepare U.S. Environmental Protection Agency's Federal Guidance Reports 12 and 13 and several publications of the International Commission on Radiological Protection. (author)

Method and software to solution of inverse and inverse design fluid flow and heat transfer problems is compatible with CFD-software

Energy Technology Data Exchange (ETDEWEB)

Krukovsky, P G [Institute of Engineering Thermophysics, National Academy of Sciences of Ukraine, Kiev (Ukraine)

1998-12-31

The description of method and software FRIEND which provide a possibility of solution of inverse and inverse design problems on the basis of existing (base) CFD-software for solution of direct problems (in particular, heat-transfer and fluid-flow problems using software PHOENICS) are presented. FRIEND is an independent additional module that widens the operational capacities of the base software unified with this module. This unifying does not require any change or addition to the base software. Interfacing of FRIEND and the base software takes place through input and output files of the base software. A brief description of the computational technique applied for the inverse problem solution, same detailed information on the interfacing of FRIEND and CFD-software and solution results for testing inverse and inverse design problems, obtained using the tandem CFD-software PHOENICS and FRIEND, are presented. (author) 9 refs.

Method and software to solution of inverse and inverse design fluid flow and heat transfer problems is compatible with CFD-software

Energy Technology Data Exchange (ETDEWEB)

Krukovsky, P.G. [Institute of Engineering Thermophysics, National Academy of Sciences of Ukraine, Kiev (Ukraine)

1997-12-31

The description of method and software FRIEND which provide a possibility of solution of inverse and inverse design problems on the basis of existing (base) CFD-software for solution of direct problems (in particular, heat-transfer and fluid-flow problems using software PHOENICS) are presented. FRIEND is an independent additional module that widens the operational capacities of the base software unified with this module. This unifying does not require any change or addition to the base software. Interfacing of FRIEND and the base software takes place through input and output files of the base software. A brief description of the computational technique applied for the inverse problem solution, same detailed information on the interfacing of FRIEND and CFD-software and solution results for testing inverse and inverse design problems, obtained using the tandem CFD-software PHOENICS and FRIEND, are presented. (author) 9 refs.

TAPSOFT'95: Theory and Practice of Software Development

DEFF Research Database (Denmark)

This volume presents the proceedings of the Sixth International Joint Conference on the Theory and Practice of Software Engineering, TAPSOFT '95, held in Aarhus, Denmark in May 1995. TAPSOFT '95 celebrates the 10th anniversary of this conference series started in Berlin in 1985 to bring together...... theoretical computer scientists and software engineers (researchers and practitioners) with a view to discussing how formal methods can usefully be applied in software development. The volume contains seven invited papers, among them one by Vaugham Pratt on the recently revealed bug in the Pentium chip...

Data collection procedures for the Software Engineering Laboratory (SEL) database

Science.gov (United States)

Heller, Gerard; Valett, Jon; Wild, Mary

1992-01-01

This document is a guidebook to collecting software engineering data on software development and maintenance efforts, as practiced in the Software Engineering Laboratory (SEL). It supersedes the document entitled Data Collection Procedures for the Rehosted SEL Database, number SEL-87-008 in the SEL series, which was published in October 1987. It presents procedures to be followed on software development and maintenance projects in the Flight Dynamics Division (FDD) of Goddard Space Flight Center (GSFC) for collecting data in support of SEL software engineering research activities. These procedures include detailed instructions for the completion and submission of SEL data collection forms.

Cessation of electronic delivery of Microsoft software for home use

CERN Multimedia

2013-01-01

Please note that electronic delivery of Microsoft software for home use is no longer available for reasons independent of CERN. The IT and FP departments are working on alternative solutions. Related links: http://cern.ch/go/microsoft-software-home-use.

Fourth Workshop on Sustainable Software for Science: Practice and Experiences (WSSSPE4)

NARCIS (Netherlands)

Katz, Daniel S; Niemeyer, Kyle E; Gesing, Sandra; Hwang, Lorraine; Bangerth, Wolfgang; Hettrick, Simon; Idaszak, Ray; Salac, Jean; Chue Hong, Neil; Núñez-Corrales, Santiago; Allen, Alice; Geiger, R Stuart; Miller, Jonah; Chen, Emily; Dubey, Anshu; Lago, Patricia

2018-01-01

This article summarizes motivations, organization, and activities of the Fourth Workshop on Sustainable Software for Science: Practice and Experiences (WSSSPE4). The WSSSPE series promotes sustainable research software by positively impacting principles and best practices, careers, learning, and

Hooke: an open software platform for force spectroscopy.

Science.gov (United States)

Sandal, Massimo; Benedetti, Fabrizio; Brucale, Marco; Gomez-Casado, Alberto; Samorì, Bruno

2009-06-01

Hooke is an open source, extensible software intended for analysis of atomic force microscope (AFM)-based single molecule force spectroscopy (SMFS) data. We propose it as a platform on which published and new algorithms for SMFS analysis can be integrated in a standard, open fashion, as a general solution to the current lack of a standard software for SMFS data analysis. Specific features and support for file formats are coded as independent plugins. Any user can code new plugins, extending the software capabilities. Basic automated dataset filtering and semi-automatic analysis facilities are included. Software and documentation are available at (http://code.google.com/p/hooke). Hooke is a free software under the GNU Lesser General Public License.

Development of a software for the curimeter model cdn102

International Nuclear Information System (INIS)

Dotres Llera, Armando

2001-01-01

The characteristics of the software for the Curimeter Model CD-N102 developed at CEADEN are presented. The software consists of two main parts: a basic software for the electrometer block and an application software for a P C. The basic software is totally independent of the Pc and performs all the basic functions of the process of measurement. The application software is optional and offers a friendlier interface and additional options to the user. Among these is the possibility to keep a statistical record of the measurements in a database, to create labels and to introduce new isotopes and calibrate them. A more detailed explanation of both software is given

Safeguarding End-User Military Software

Science.gov (United States)

2014-12-04

software engineering techniques fail to address the salient characteristics of ULS systems. Furthermore, they do not integrate the feedback, expertise...independently executing Firefox clients . The study showed that workarounds for all but one of the seeded faults are found and the one that is not found never

CrossTalk. The Journal of Defense Software Engineering. Volume 26, Number 1

Science.gov (United States)

2013-02-01

comprehen- sive software development process, which incorporates best practices as well as standards such as IEEE 12207 -2008. The contractor will be...5], defines software quality as the degree to which software possesses a desired combination of attributes. Similarly, ISO /IEC 9126-1:2001 [6], one...attributes of the quality characteristics defined in ISO /IEC 9126-1. It should be noted that the 9126-series is being revised as part of the Software Product

Tracking code patterns over multiple software versions with Herodotos

DEFF Research Database (Denmark)

Palix, Nicolas Jean-Michel; Lawall, Julia; Muller, Gilles

2010-01-01

An important element of understanding a software code base is to identify the repetitive patterns of code it contains and how these evolve over time. Some patterns are useful to the software, and may be modularized. Others are detrimental to the software, such as patterns that represent defects...... pattern occurrences over multiple versions of a software project, independent of other changes in the source files. Guided by a user-provided configuration file, Herodotos builds various graphs showing the evolution of the pattern occurrences and computes some statistics. We have evaluated this approach...

Software Service Engineering : Tenets and Challenges

NARCIS (Netherlands)

Heuvel, Willem-Jan van den; Zimmermann, Olaf; Leymann, Frank; Lago, Patricia; Schieferdecker, Ina; Zdun, Uwe; Avgeriou, Paris

2009-01-01

Service-Oriented Architecture (SOA) constitutes a modern, standards-based and technology-independent paradigm and architectural style for distributed enterprise computing. The SOA style promotes the publishing, discovery, and binding of loosely-coupled, network-accessible software services. With SOA

CernVM - a virtual software appliance for LHC applications

International Nuclear Information System (INIS)

Buncic, P; Sanchez, C Aguado; Blomer, J; Franco, L; Mato, P; Harutyunian, A; Yao, Y

2010-01-01

CernVM is a Virtual Software Appliance capable of running physics applications from the LHC experiments at CERN. It aims to provide a complete and portable environment for developing and running LHC data analysis on any end-user computer (laptop, desktop) as well as on the Grid, independently of Operating System platforms (Linux, Windows, MacOS). The experiment application software and its specific dependencies are built independently from CernVM and delivered to the appliance just in time by means of a CernVM File System (CVMFS) specifically designed for efficient software distribution. The procedures for building, installing and validating software releases remains under the control and responsibility of each user community. We provide a mechanism to publish pre-built and configured experiment software releases to a central distribution point from where it finds its way to the running CernVM instances via the hierarchy of proxy servers or content delivery networks. In this paper, we present current state of CernVM project and compare performance of CVMFS to performance of traditional network file system like AFS and discuss possible scenarios that could further improve its performance and scalability.

A measurement system for large, complex software programs

Science.gov (United States)

Rone, Kyle Y.; Olson, Kitty M.; Davis, Nathan E.

1994-01-01

This paper describes measurement systems required to forecast, measure, and control activities for large, complex software development and support programs. Initial software cost and quality analysis provides the foundation for meaningful management decisions as a project evolves. In modeling the cost and quality of software systems, the relationship between the functionality, quality, cost, and schedule of the product must be considered. This explicit relationship is dictated by the criticality of the software being developed. This balance between cost and quality is a viable software engineering trade-off throughout the life cycle. Therefore, the ability to accurately estimate the cost and quality of software systems is essential to providing reliable software on time and within budget. Software cost models relate the product error rate to the percent of the project labor that is required for independent verification and validation. The criticality of the software determines which cost model is used to estimate the labor required to develop the software. Software quality models yield an expected error discovery rate based on the software size, criticality, software development environment, and the level of competence of the project and developers with respect to the processes being employed.

Trends in computer hardware and software.

Science.gov (United States)

Frankenfeld, F M

1993-04-01

Previously identified and current trends in the development of computer systems and in the use of computers for health care applications are reviewed. Trends identified in a 1982 article were increasing miniaturization and archival ability, increasing software costs, increasing software independence, user empowerment through new software technologies, shorter computer-system life cycles, and more rapid development and support of pharmaceutical services. Most of these trends continue today. Current trends in hardware and software include the increasing use of reduced instruction-set computing, migration to the UNIX operating system, the development of large software libraries, microprocessor-based smart terminals that allow remote validation of data, speech synthesis and recognition, application generators, fourth-generation languages, computer-aided software engineering, object-oriented technologies, and artificial intelligence. Current trends specific to pharmacy and hospitals are the withdrawal of vendors of hospital information systems from the pharmacy market, improved linkage of information systems within hospitals, and increased regulation by government. The computer industry and its products continue to undergo dynamic change. Software development continues to lag behind hardware, and its high cost is offsetting the savings provided by hardware.

Validation testing of safety-critical software

International Nuclear Information System (INIS)

Kim, Hang Bae; Han, Jae Bok

1995-01-01

A software engineering process has been developed for the design of safety critical software for Wolsung 2/3/4 project to satisfy the requirements of the regulatory body. Among the process, this paper described the detail process of validation testing performed to ensure that the software with its hardware, developed by the design group, satisfies the requirements of the functional specification prepared by the independent functional group. To perform the tests, test facility and test software were developed and actual safety system computer was connected. Three kinds of test cases, i.e., functional test, performance test and self-check test, were programmed and run to verify each functional specifications. Test failures were feedback to the design group to revise the software and test results were analyzed and documented in the report to submit to the regulatory body. The test methodology and procedure were very efficient and satisfactory to perform the systematic and automatic test. The test results were also acceptable and successful to verify the software acts as specified in the program functional specification. This methodology can be applied to the validation of other safety-critical software. 2 figs., 2 tabs., 14 refs. (Author)

Recent trends on Software Verification and Validation Testing

International Nuclear Information System (INIS)

Kim, Hyungtae; Jeong, Choongheui

2013-01-01

Verification and Validation (V and V) include the analysis, evaluation, review, inspection, assessment, and testing of products. Especially testing is an important method to verify and validate software. Software V and V testing covers test planning to execution. IEEE Std. 1012 is a standard on the software V and V. Recently, IEEE Std. 1012-2012 was published. This standard is a major revision to IEEE Std. 1012-2004 which defines only software V and V. It expands the scope of the V and V processes to include system and hardware as well as software. This standard describes the scope of V and V testing according to integrity level. In addition, independent V and V requirement related to software V and V testing in IEEE 7-4.3.2-2010 have been revised. This paper provides a recent trend of software V and V testing by reviewing of IEEE Std. 1012-2012 and IEEE 7-4.3.2-2010. There are no major changes of software V and V testing activities and tasks in IEEE 1012-2012 compared with IEEE 1012-2004. But the positions on the responsibility to perform software V and V testing are changed. In addition IEEE 7-4.3.2-2010 newly describes the positions on responsibility to perform Software V and V Testing. However, the positions of these standards on the V and V testing are different. For integrity level 3 and 4, IEEE 1012-2012 basically requires that V and V organization shall conduct all of V and V testing tasks such as test plan, test design, test case, and test procedure except test execution. If V and V testing is conducted by not V and V but another organization, the results of that testing shall be analyzed by the V and V organization. For safety-related software, IEEE 7-4.3.2-2010 requires that test procedures and reports shall be independently verified by the alternate organization regardless of who writes the procedures and/or conducts the tests

Visual time series analysis

DEFF Research Database (Denmark)

Fischer, Paul; Hilbert, Astrid

2012-01-01

We introduce a platform which supplies an easy-to-handle, interactive, extendable, and fast analysis tool for time series analysis. In contrast to other software suits like Maple, Matlab, or R, which use a command-line-like interface and where the user has to memorize/look-up the appropriate...... commands, our application is select-and-click-driven. It allows to derive many different sequences of deviations for a given time series and to visualize them in different ways in order to judge their expressive power and to reuse the procedure found. For many transformations or model-ts, the user may...... choose between manual and automated parameter selection. The user can dene new transformations and add them to the system. The application contains efficient implementations of advanced and recent techniques for time series analysis including techniques related to extreme value analysis and filtering...

Seeding the cloud: Financial bootstrapping in the computer software sector

OpenAIRE

Mac An Bhaird, Ciarán; Lynn, Theo

2015-01-01

This study investigates resourcing of computer software companies that have adopted cloud computing for the development and delivery of application software. Use of this innovative technology potentially impacts firm financing because the initial infrastructure investment requirement is much lower than for packaged software, lead time to market is shorter, and cloud computing supports instant scalability. We test these predictions by conducting in-depth interviews with founders of 18 independ...

Summary of the International Conference on Software and System Processes

DEFF Research Database (Denmark)

Kuhrmann, Marco; O'Connor, Rory V.; Perry, Dewayne E.

2016-01-01

The International Conference on Software and Systems Process (ICSSP), continuing the success of Software Process Workshop (SPW), the Software Process Modeling and Simulation Workshop (ProSim) and the International Conference on Software Process (ICSP) conference series, has become the established...... premier event in the field of software and systems engineering processes. It provides a leading forum for the exchange of research outcomes and industrial best-practices in process development from software and systems disciplines. ICSSP 2016 was held in Austin, Texas, from 14-15 May 2016, co......-located with the 38th International Conference on Software Engineering (ICSE). The theme of mICSSP 2016 was studying "Process(es) in Action" by recognizing that the AS-Planned and AS-Practiced processes can be quite different in many ways including their ows, their complexity and the evolving needs of stakeholders...

A Platform-Independent Plugin for Navigating Online Radiology Cases.

Science.gov (United States)

Balkman, Jason D; Awan, Omer A

2016-06-01

Software methods that enable navigation of radiology cases on various digital platforms differ between handheld devices and desktop computers. This has resulted in poor compatibility of online radiology teaching files across mobile smartphones, tablets, and desktop computers. A standardized, platform-independent, or "agnostic" approach for presenting online radiology content was produced in this work by leveraging modern hypertext markup language (HTML) and JavaScript web software technology. We describe the design and evaluation of this software, demonstrate its use across multiple viewing platforms, and make it publicly available as a model for future development efforts.

General software design for multisensor data fusion

Science.gov (United States)

Zhang, Junliang; Zhao, Yuming

1999-03-01

In this paper a general method of software design for multisensor data fusion is discussed in detail, which adopts object-oriented technology under UNIX operation system. The software for multisensor data fusion is divided into six functional modules: data collection, database management, GIS, target display and alarming data simulation etc. Furthermore, the primary function, the components and some realization methods of each modular is given. The interfaces among these functional modular relations are discussed. The data exchange among each functional modular is performed by interprocess communication IPC, including message queue, semaphore and shared memory. Thus, each functional modular is executed independently, which reduces the dependence among functional modules and helps software programing and testing. This software for multisensor data fusion is designed as hierarchical structure by the inheritance character of classes. Each functional modular is abstracted and encapsulated through class structure, which avoids software redundancy and enhances readability.

Self-Contained Cross-Cutting Pipeline Software Architecture

OpenAIRE

Patwardhan, Amol; Patwardhan, Rahul; Vartak, Sumalini

2016-01-01

Layered software architecture contains several intra-layer and inter-layer dependencies. Each layer depends on shared components making it difficult to release a code change, bug fix or feature without exhaustive testing and having to build the entire software code base. This paper proposed self-contained, cross-cutting pipeline architecture (SCPA) that is independent of existing layers. We chose 2 open source projects and 3 internal intern projects that used n-tier architecture and applied t...

Safety review on unit testing of safety system software of nuclear power plant

International Nuclear Information System (INIS)

Liu Le; Zhang Qi

2013-01-01

Software unit testing has an important place in the testing of safety system software of nuclear power plants, and in the wider scope of the verification and validation. It is a comprehensive, systematic process, and its documentation shall meet the related requirements. When reviewing software unit testing, attention should be paid to the coverage of software safety requirements, the coverage of software internal structure, and the independence of the work. (authors)

Supporting Usability Engineering in Small Software Development Organizations

DEFF Research Database (Denmark)

Bornoe, Nis; Stage, Jan

2013-01-01

Despite an interest and use of different usability engineering methods small software development organizations find it challenging to implement usability engineering into the software development process. We present the results from a study about usability engineering in practice. Through a series...... of semistructured interviews we want to get an understanding of how usability is implemented into the organizations and how it’s practiced in reality. We found that the developers found it problematic to combine agile software development methods with classic usability engineering methods. A lack of solid usability...... engineering expertise and not least experience seems to be a main obstacle for a successful implementation of usability engineering into current software development practices. They are requesting methods and procedures that fit better with their current practices and strategies to implement usability...

Controleum - an independently extensible control system

DEFF Research Database (Denmark)

Jensen, Martin Lykke Rytter

2014-01-01

challenging kind of system to design for independent extension. This thesis presents two new software technologies that improve the extensibility of control systems: First, the concept of dynamic links is introduced and Decouplink – an implementation of dynamic links for Java - is presented. Dynamic links...... is introduced, and an implementation is presented. The extensible controller is a component framework designed to automatically resolve conflicts among mutually unaware components in a control system. The solution is based on the idea that independent components implement different kinds of control concerns...

GRACAT, Software for grounding and collision analysis

DEFF Research Database (Denmark)

Friis-Hansen, Peter; Simonsen, Bo Cerup

2002-01-01

and grounding accidents. The software consists of three basic analysis modules and one risk mitigation module: 1) frequency, 2) damage, and 3) consequence. These modules can be used individually or in series and the analyses can be performed in deterministic or probabilistic mode. Finally, in the mitigation...

KAERI software verification and validation guideline for developing safety-critical software in digital I and C system of NPP

Energy Technology Data Exchange (ETDEWEB)

Kim, Jang Yeol; Lee, Jang Soo; Eom, Heung Seop

1997-07-01

This technical report is to present V and V guideline development methodology for safety-critical software in NPP safety system. Therefore it is to present V and V guideline of planning phase for the NPP safety system in addition to critical safety items, for example, independence philosophy, software safety analysis concept, commercial off the shelf (COTS) software evaluation criteria, inter-relationships between other safety assurance organizations, including the concepts of existing industrial standard, IEEE Std-1012, IEEE Std-1059. This technical report includes scope of V and V guideline, guideline framework as part of acceptance criteria, V and V activities and task entrance as part of V and V activity and exit criteria, review and audit, testing and QA records of V and V material and configuration management, software verification and validation plan production etc., and safety-critical software V and V methodology. (author). 11 refs.

KAERI software verification and validation guideline for developing safety-critical software in digital I and C system of NPP

International Nuclear Information System (INIS)

Kim, Jang Yeol; Lee, Jang Soo; Eom, Heung Seop.

1997-07-01

This technical report is to present V and V guideline development methodology for safety-critical software in NPP safety system. Therefore it is to present V and V guideline of planning phase for the NPP safety system in addition to critical safety items, for example, independence philosophy, software safety analysis concept, commercial off the shelf (COTS) software evaluation criteria, inter-relationships between other safety assurance organizations, including the concepts of existing industrial standard, IEEE Std-1012, IEEE Std-1059. This technical report includes scope of V and V guideline, guideline framework as part of acceptance criteria, V and V activities and task entrance as part of V and V activity and exit criteria, review and audit, testing and QA records of V and V material and configuration management, software verification and validation plan production etc., and safety-critical software V and V methodology. (author). 11 refs

SU-E-T-50: A Multi-Institutional Study of Independent Dose Verification Software Program for Lung SBRT

International Nuclear Information System (INIS)

Kawai, D; Takahashi, R; Kamima, T; Baba, H; Yamamoto, T; Kubo, Y; Ishibashi, S; Higuchi, Y; Takahashi, H; Tachibana, H

2015-01-01

Purpose: The accuracy of dose distribution depends on treatment planning system especially in heterogeneity-region. The tolerance level (TL) of the secondary check using the independent dose verification may be variable in lung SBRT plans. We conducted a multi-institutional study to evaluate the tolerance level of lung SBRT plans shown in the AAPM TG114. Methods: Five institutes in Japan participated in this study. All of the institutes used a same independent dose verification software program (Simple MU Analysis: SMU, Triangle Product, Ishikawa, JP), which is Clarkson-based and CT images were used to compute radiological path length. Analytical Anisotropic Algorithm (AAA), Pencil Beam Convolution with modified Batho-method (PBC-B) and Adaptive Convolve (AC) were used for lung SBRT planning. A measurement using an ion-chamber was performed in a heterogeneous phantom to compare doses from the three different algorithms and the SMU to the measured dose. In addition to it, a retrospective analysis using clinical lung SBRT plans (547 beams from 77 patients) was conducted to evaluate the confidence limit (CL, Average±2SD) in dose between the three algorithms and the SMU. Results: Compared to the measurement, the AAA showed the larger systematic dose error of 2.9±3.2% than PBC-B and AC. The Clarkson-based SMU showed larger error of 5.8±3.8%. The CLs for clinical plans were 7.7±6.0 % (AAA), 5.3±3.3 % (AC), 5.7±3.4 % (PBC -B), respectively. Conclusion: The TLs from the CLs were evaluated. A Clarkson-based system shows a large systematic variation because of inhomogeneous correction. The AAA showed a significant variation. Thus, we must consider the difference of inhomogeneous correction as well as the dependence of dose calculation engine

SU-E-T-50: A Multi-Institutional Study of Independent Dose Verification Software Program for Lung SBRT

Energy Technology Data Exchange (ETDEWEB)

Kawai, D [Kanagawa Cancer Center, Yokohama, Kanagawa-prefecture (Japan); Takahashi, R; Kamima, T [The Cancer Institute Hospital of JFCR, Koutou-ku, Tokyo (Japan); Baba, H [The National Cancer Center Hospital East, Kashiwa-city, Chiba prefecture (Japan); Yamamoto, T; Kubo, Y [Otemae Hospital, Chuou-ku, Osaka-city (Japan); Ishibashi, S; Higuchi, Y [Sasebo City General Hospital, Sasebo, Nagasaki (Japan); Takahashi, H [St Lukes International Hospital, Chuou-ku, Tokyo (Japan); Tachibana, H [National Cancer Center Hospital East, Kashiwa, Chiba (Japan)

2015-06-15

Purpose: The accuracy of dose distribution depends on treatment planning system especially in heterogeneity-region. The tolerance level (TL) of the secondary check using the independent dose verification may be variable in lung SBRT plans. We conducted a multi-institutional study to evaluate the tolerance level of lung SBRT plans shown in the AAPM TG114. Methods: Five institutes in Japan participated in this study. All of the institutes used a same independent dose verification software program (Simple MU Analysis: SMU, Triangle Product, Ishikawa, JP), which is Clarkson-based and CT images were used to compute radiological path length. Analytical Anisotropic Algorithm (AAA), Pencil Beam Convolution with modified Batho-method (PBC-B) and Adaptive Convolve (AC) were used for lung SBRT planning. A measurement using an ion-chamber was performed in a heterogeneous phantom to compare doses from the three different algorithms and the SMU to the measured dose. In addition to it, a retrospective analysis using clinical lung SBRT plans (547 beams from 77 patients) was conducted to evaluate the confidence limit (CL, Average±2SD) in dose between the three algorithms and the SMU. Results: Compared to the measurement, the AAA showed the larger systematic dose error of 2.9±3.2% than PBC-B and AC. The Clarkson-based SMU showed larger error of 5.8±3.8%. The CLs for clinical plans were 7.7±6.0 % (AAA), 5.3±3.3 % (AC), 5.7±3.4 % (PBC -B), respectively. Conclusion: The TLs from the CLs were evaluated. A Clarkson-based system shows a large systematic variation because of inhomogeneous correction. The AAA showed a significant variation. Thus, we must consider the difference of inhomogeneous correction as well as the dependence of dose calculation engine.

Evaluation procedure of software safety plan for digital I and C of KNGR

International Nuclear Information System (INIS)

Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kwon, Ki Choon; Kim, Jang Yeol; Cheon, Se Woo

2000-05-01

The development, use, and regulation of computer systems in nuclear reactor instrumentation and control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean next generation reactor (KNGR) software safety verification and validation (SSVV) task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations. The requirements for software important to safety of nuclear reactor are described in such positions and standards, for example, the new standard review plan (SRP), IEC 880 supplements, IEEE standard 1228-1994, IEEE standard 7-4.3.2-1993, and IAEA safety series No. 50-SG-D3 and D8. We presented the guidance for evaluating the safety plan of the software in the KNGR protection systems. The guideline consists of the regulatory requirements for software safety in chapter 2, the evaluation checklist of software safety plan in chapter3, and the evaluation results of KNGR software safety plan in chapter 4

Evaluation procedure of software safety plan for digital I and C of KNGR

Energy Technology Data Exchange (ETDEWEB)

Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kwon, Ki Choon; Kim, Jang Yeol; Cheon, Se Woo

2000-05-01

The development, use, and regulation of computer systems in nuclear reactor instrumentation and control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean next generation reactor (KNGR) software safety verification and validation (SSVV) task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the safety planning for safety-critical software systems is being recognized as the most important phase in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations. The requirements for software important to safety of nuclear reactor are described in such positions and standards, for example, the new standard review plan (SRP), IEC 880 supplements, IEEE standard 1228-1994, IEEE standard 7-4.3.2-1993, and IAEA safety series No. 50-SG-D3 and D8. We presented the guidance for evaluating the safety plan of the software in the KNGR protection systems. The guideline consists of the regulatory requirements for software safety in chapter 2, the evaluation checklist of software safety plan in chapter3, and the evaluation results of KNGR software safety plan in chapter 4.

An Exploratory Study of Software Cost Estimating at the Electronic Systems Division.

Science.gov (United States)

1976-07-01

action’. to improve the software cost Sestimating proces., While thin research was limited to the M.nD onvironment, the same types of problema may exist...Methods in Social Science. Now York: Random House, 1969. 57. Smith, Ronald L. Structured Programming Series (Vol. XI) - Estimating Software Project

Recommendations for a software quality assurance policy for the nuclear waste disposal risk assessment programme

International Nuclear Information System (INIS)

Hill, I.E.

1985-05-01

This study reviewed a number of published standards for software quality assurance, and included a series of interviews with software developers aimed at exploring their attitudes to software quality assurance. Recommendations for software quality assurance policy are made based on the above investigations. This document provides a summary of the recommendations made in the full report on project, reference MR-CDS-4. (author)

Building Software Development Capacity to Advance the State of Educational Technology

Science.gov (United States)

Luterbach, Kenneth J.

2013-01-01

Educational technologists may advance the state of the field by increasing capacity to develop software tools and instructional applications. Presently, few academic programs in educational technology require even a single computer programming course. Further, the educational technologists who develop software generally work independently or in…

Software diversity: way to enhance safety?

International Nuclear Information System (INIS)

Dahll, G.; Bishop, P.

1990-01-01

The topic of the paper is the use of diversely produced programs to enhance the safety of computer-based systems applied in safety-critical areas. The paper starts with a survey of scientific investigations on the impact of software redundancy made at various institutions around the world. Main emphasis will, however, be put on the PODS/STEM projects, which have been performed at the OECD Halden Project in cooperation with the Technical Research Center of Finland, the Safety and Reliability Directorate, AEA Technology, UK, and Central Electricity Research Laboratory (now National Power Technology and Environment Centre), UK. In these projects, three program versions were made independently by three different teams, all based on the same specification. The three programs were tested back-to-back with a large amount of test data. The experience and results from this process were carefully logged and used for further analysis. Various strategies for test data selection were compared, with respect to fault finding strategies, as well as to branch and statement coverages of the tested programs. The assumption of independence of failures in diversely produced programs was investigated. A particularly interesting effect, namely failure masking due to program structure, was revealed. Static analysis techniques, software measures, and software reliability estimates were also studied. (author)

EDS operator and control software

International Nuclear Information System (INIS)

Ott, L.L.

1985-04-01

The Enrichment Diagnostic System (EDS) was developed at Lawrence Livermore National Laboratory (LLNL) to acquire, display and analyze large quantities of transient data for a real-time Advanced Vapor Laser Isotope Separation (AVLIS) experiment. Major topics discussed in this paper are the EDS operator interface (SHELL) program, the data acquisition and analysis scheduling software, and the graphics software. The workstation concept used in EDS, the software used to configure a user's workstation, and the ownership and management of a diagnostic are described. An EDS diagnostic is a combination of hardware and software designed to study specific aspects of the process. Overall system performance is discussed from the standpoint of scheduling techniques, evaluation tools, optimization techniques, and program-to-program communication methods. EDS is based on a data driven design which keeps the need to modify software to a minimum. This design requires a fast and reliable data base management system. A third party data base management product, Berkeley Software System Database, written explicitly for HP1000's, is used for all EDS data bases. All graphics is done with an in-house graphics product, Device Independent Graphics Library (DIGLIB). Examples of devices supported by DIGLIB are: Versatec printer/plotters, Raster Technologies Graphic Display Controllers, and HP terminals (HP264x and HP262x). The benefits derived by using HP hardware and software as well as obstacles imposed by the HP environment are presented in relation to EDS development and implementation

Agent independent task planning

Science.gov (United States)

Davis, William S.

1990-01-01

Agent-Independent Planning is a technique that allows the construction of activity plans without regard to the agent that will perform them. Once generated, a plan is then validated and translated into instructions for a particular agent, whether a robot, crewmember, or software-based control system. Because Space Station Freedom (SSF) is planned for orbital operations for approximately thirty years, it will almost certainly experience numerous enhancements and upgrades, including upgrades in robotic manipulators. Agent-Independent Planning provides the capability to construct plans for SSF operations, independent of specific robotic systems, by combining techniques of object oriented modeling, nonlinear planning and temporal logic. Since a plan is validated using the physical and functional models of a particular agent, new robotic systems can be developed and integrated with existing operations in a robust manner. This technique also provides the capability to generate plans for crewmembers with varying skill levels, and later apply these same plans to more sophisticated robotic manipulators made available by evolutions in technology.

Managing MDO Software Development Projects

Science.gov (United States)

Townsend, J. C.; Salas, A. O.

2002-01-01

Over the past decade, the NASA Langley Research Center developed a series of 'grand challenge' applications demonstrating the use of parallel and distributed computation and multidisciplinary design optimization. All but the last of these applications were focused on the high-speed civil transport vehicle; the final application focused on reusable launch vehicles. Teams of discipline experts developed these multidisciplinary applications by integrating legacy engineering analysis codes. As teams became larger and the application development became more complex with increasing levels of fidelity and numbers of disciplines, the need for applying software engineering practices became evident. This paper briefly introduces the application projects and then describes the approaches taken in project management and software engineering for each project; lessons learned are highlighted.

Controlatron Neutron Tube Test Suite Software Manual - Operation Manual (V2.2)

CERN Document Server

Noel, W P; Hertrich, R J; Martinez, M L; Wallace, D L

2002-01-01

The Controlatron Software Suite is a custom built application to perform automated testing of Controlatron neutron tubes. The software package was designed to allowing users to design tests and to run a series of test suites on a tube. The data is output to ASCII files of a pre-defined format for data analysis and viewing with the Controlatron Data Viewer Application. This manual discusses the operation of the Controlatron Test Suite Software and a brief discussion of state machine theory, as state machine is the functional basis of the software.

Diversity requirements for safety critical software-based automation systems

International Nuclear Information System (INIS)

Korhonen, J.; Pulkkinen, U.; Haapanen, P.

1998-03-01

System vendors nowadays propose software-based systems even for the most critical safety functions in nuclear power plants. Due to the nature and mechanisms of influence of software faults new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)' various safety assessment methods and tools for software based systems are developed and evaluated. This report first discusses the (common cause) failure mechanisms in software-based systems, then defines fault-tolerant system architectures to avoid common cause failures, then studies the various alternatives to apply diversity and their influence on system reliability. Finally, a method for the assessment of diversity is described. Other recently published reports in OHA-report series handles the statistical reliability assessment of software based (STUK-YTO-TR 119), usage models in reliability assessment of software-based systems (STUK-YTO-TR 128) and handling of programmable automation in plant PSA-studies (STUK-YTO-TR 129)

High Energy Physics Forum for Computational Excellence: Working Group Reports (I. Applications Software II. Software Libraries and Tools III. Systems)

Energy Technology Data Exchange (ETDEWEB)

Habib, Salman [Argonne National Lab. (ANL), Argonne, IL (United States); Roser, Robert [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); LeCompte, Tom [Argonne National Lab. (ANL), Argonne, IL (United States); Marshall, Zach [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Borgland, Anders [SLAC National Accelerator Lab., Menlo Park, CA (United States); Viren, Brett [Brookhaven National Lab. (BNL), Upton, NY (United States); Nugent, Peter [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Asai, Makato [SLAC National Accelerator Lab., Menlo Park, CA (United States); Bauerdick, Lothar [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Finkel, Hal [Argonne National Lab. (ANL), Argonne, IL (United States); Gottlieb, Steve [Indiana Univ., Bloomington, IN (United States); Hoeche, Stefan [SLAC National Accelerator Lab., Menlo Park, CA (United States); Sheldon, Paul [Vanderbilt Univ., Nashville, TN (United States); Vay, Jean-Luc [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Elmer, Peter [Princeton Univ., NJ (United States); Kirby, Michael [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Patton, Simon [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Potekhin, Maxim [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Yanny, Brian [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Calafiura, Paolo [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Dart, Eli [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gutsche, Oliver [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Izubuchi, Taku [Brookhaven National Lab. (BNL), Upton, NY (United States); Lyon, Adam [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Petravick, Don [Univ. of Illinois, Urbana-Champaign, IL (United States). National Center for Supercomputing Applications (NCSA)

2015-10-29

Computing plays an essential role in all aspects of high energy physics. As computational technology evolves rapidly in new directions, and data throughput and volume continue to follow a steep trend-line, it is important for the HEP community to develop an effective response to a series of expected challenges. In order to help shape the desired response, the HEP Forum for Computational Excellence (HEP-FCE) initiated a roadmap planning activity with two key overlapping drivers -- 1) software effectiveness, and 2) infrastructure and expertise advancement. The HEP-FCE formed three working groups, 1) Applications Software, 2) Software Libraries and Tools, and 3) Systems (including systems software), to provide an overview of the current status of HEP computing and to present findings and opportunities for the desired HEP computational roadmap. The final versions of the reports are combined in this document, and are presented along with introductory material.

High Energy Physics Forum for Computational Excellence: Working Group Reports (I. Applications Software II. Software Libraries and Tools III. Systems)

Energy Technology Data Exchange (ETDEWEB)

Habib, Salman [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Roser, Robert [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

2015-10-28

Computing plays an essential role in all aspects of high energy physics. As computational technology evolves rapidly in new directions, and data throughput and volume continue to follow a steep trend-line, it is important for the HEP community to develop an effective response to a series of expected challenges. In order to help shape the desired response, the HEP Forum for Computational Excellence (HEP-FCE) initiated a roadmap planning activity with two key overlapping drivers -- 1) software effectiveness, and 2) infrastructure and expertise advancement. The HEP-FCE formed three working groups, 1) Applications Software, 2) Software Libraries and Tools, and 3) Systems (including systems software), to provide an overview of the current status of HEP computing and to present findings and opportunities for the desired HEP computational roadmap. The final versions of the reports are combined in this document, and are presented along with introductory material.

Clinical experience of quantex coordinate software for CT guided stereotactic surgery

International Nuclear Information System (INIS)

Yabashi, Toshitake; Ichikawa, Hideo; Yasuda, Eisuke; Tsuruta, Hatsuo; Ishikawa, Yoshihisa; Kimura, Tokuji; Kanamori, Isao

1991-01-01

Recently, Quantex Coordinate Software was newly developed for CT-guided stereotactic surgery. We have the opportunity of using this software in 6 cases with intracerebral hematoma for evacuation and 2 cases with brain tumor for needle biopsy by using CT-guided stereotactic surgery. The followings are the features with a little clinical experience. One of the biggest features is that this software can simulate the best expected route of the puncture needle from burr hole to target point before inserting. Also compared with CT 9000 series Software, it has many new functions for more advanced hardware as well as advance standard software. Two cases of intracerebral hematoma for evacuation and 1 case of a brain tumor for a biopsy were carried out using this software mainly as a simulation. In all cases, this software proved to be very useful. (author)

Mining dynamic noteworthy functions in software execution sequences.

Science.gov (United States)

Zhang, Bing; Huang, Guoyan; Wang, Yuqian; He, Haitao; Ren, Jiadong

2017-01-01

As the quality of crucial entities can directly affect that of software, their identification and protection become an important premise for effective software development, management, maintenance and testing, which thus contribute to improving the software quality and its attack-defending ability. Most analysis and evaluation on important entities like codes-based static structure analysis are on the destruction of the actual software running. In this paper, from the perspective of software execution process, we proposed an approach to mine dynamic noteworthy functions (DNFM)in software execution sequences. First, according to software decompiling and tracking stack changes, the execution traces composed of a series of function addresses were acquired. Then these traces were modeled as execution sequences and then simplified so as to get simplified sequences (SFS), followed by the extraction of patterns through pattern extraction (PE) algorithm from SFS. After that, evaluating indicators inner-importance and inter-importance were designed to measure the noteworthiness of functions in DNFM algorithm. Finally, these functions were sorted by their noteworthiness. Comparison and contrast were conducted on the experiment results from two traditional complex network-based node mining methods, namely PageRank and DegreeRank. The results show that the DNFM method can mine noteworthy functions in software effectively and precisely.

Software Engineering Research/Developer Collaborations (C104)

Science.gov (United States)

Shell, Elaine; Shull, Forrest

2005-01-01

The goal of this collaboration was to produce Flight Software Branch (FSB) process standards for software inspections which could be used across three new missions within the FSB. The standard was developed by Dr. Forrest Shull (Fraunhofer Center for Experimental Software Engineering, Maryland) using the Perspective-Based Inspection approach, (PBI research has been funded by SARP) , then tested on a pilot Branch project. Because the short time scale of the collaboration ruled out a quantitative evaluation, it would be decided whether the standard was suitable for roll-out to other Branch projects based on a qualitative measure: whether the standard received high ratings from Branch personnel as to usability and overall satisfaction. The project used for piloting the Perspective-Based Inspection approach was a multi-mission framework designed for reuse. This was a good choice because key representatives from the three new missions would be involved in the inspections. The perspective-based approach was applied to produce inspection procedures tailored for the specific quality needs of the branch. The technical information to do so was largely drawn through a series of interviews with Branch personnel. The framework team used the procedures to review requirements. The inspections were useful for indicating that a restructuring of the requirements document was needed, which led to changes in the development project plan. The standard was sent out to other Branch personnel for review. Branch personnel were very positive. However, important changes were identified because the perspective of Attitude Control System (ACS) developers had not been adequately represented, a result of the specific personnel interviewed. The net result is that with some further work to incorporate the ACS perspective, and in synchrony with the roll out of independent Branch standards, the PBI approach will be implemented in the FSB. Also, the project intends to continue its collaboration with

Westinghouse integrated protection system. An overview of the software design and maintenance features

International Nuclear Information System (INIS)

Gibson, R.J.

1995-01-01

The Westinghouse Integrated Protection System was designed with the goal of providing a system which can be easily verified, validated, and maintained. The software design and structure promote the ease of translation from functional requirements to applications function software while also improving the ability to verify and maintain the applications function software. The use of independent, reusable, common functions software modules focuses the design, verification, and validation of the software and reduces the likelihood of errors occurring during the application and maintenance of the software. The simple continuous loop method of operation used throughout the IPS provides a standard deterministic method of operation. The IPS design also incorporates the use of embedded self-diagnostics to perform continuous hardware oriented tests of the system and the use of an independent subsystem to automatically perform a functional test of the system. Maintenance interfaces also exist to readily identify and locate faults as well as providing other maintenance capabilities. These testing and maintenance features enhance the overall reliability and availability of the system. (orig.) (2 refs., 2 figs.)

2006 XSD Scientific Software Workshop report.

Energy Technology Data Exchange (ETDEWEB)

Evans, K., Jr.; De Carlo, F.; Jemian, P.; Lang, J.; Lienert, U.; Maclean, J.; Newville, M.; Tieman, B.; Toby, B.; van Veenendaal, B.; Univ. of Chicago

2006-01-22

In May of 2006, a committee was formed to assess the fundamental needs and opportunities in scientific software for x-ray data reduction, analysis, modeling, and simulation. This committee held a series of discussions throughout the summer, conducted a poll of the members of the x-ray community, and held a workshop. This report details the findings and recommendations of the committee. Each experiment performed at the APS requires three crucial ingredients: the powerful x-ray source, an optimized instrument to perform measurements, and computer software to acquire, visualize, and analyze the experimental observations. While the APS has invested significant resources in the accelerator, investment in other areas such as scientific software for data analysis and visualization has lagged behind. This has led to the adoption of a wide variety of software with variable levels of usability. In order to maximize the scientific output of the APS, it is essential to support the broad development of real-time analysis and data visualization software. As scientists attack problems of increasing sophistication and deal with larger and more complex data sets, software is playing an ever more important role. Furthermore, our need for excellent and flexible scientific software can only be expected to increase, as the upgrade of the APS facility and the implementation of advanced detectors create a host of new measurement capabilities. New software analysis tools must be developed to take full advantage of these capabilities. It is critical that the APS take the lead in software development and the implementation of theory to software to ensure the continued success of this facility. The topics described in this report are relevant to the APS today and critical for the APS upgrade plan. Implementing these recommendations will have a positive impact on the scientific productivity of the APS today and will be even more critical in the future.

[Confirming the Utility of RAISUS Antifungal Susceptibility Testing by New-Software].

Science.gov (United States)

Ono, Tomoko; Suematsu, Hiroyuki; Sawamura, Haruki; Yamagishi, Yuka; Mikamo, Hiroshige

2017-08-15

Clinical and Laboratory Standards Institute (CLSI) methods for susceptibility tests of yeast are used in Japan. On the other hand, the methods have some disadvantage; 1) reading at 24 and 48 h, 2) using unclear scale, approximately 50% inhibition, to determine MICs, 3) calculating trailing growth and paradoxical effects. These makes it difficult to test the susuceptibility for yeasts. Old software of RAISUS, Ver. 6.0 series, resolved problem 1) and 2) but did not resolve problem 3). Recently, new software of RAISUS, Ver. 7.0 series, resolved problem 3). We confirmed that using the new software made it clear whether all these issue were settled or not. Eighty-four Candida isolated from Aichi Medical University was used in this study. We compared the MICs obtained by using RAISUS antifungal susceptibility testing of yeasts RSMY1, RSMY1, with those obtained by using ASTY. The concordance rates (±four-fold of MICs) between the MICs obtained by using ASTY and RSMY1 with the new software were more than 90%, except for miconazole (MCZ). The rate of MCZ was low, but MICs obtained by using CLSI methods and Yeast-like Fungus DP 'EIKEN' methods, E-DP, showed equivalent MICs of RSMY1 using the new software. The frequency of skip effects on RSMY1 using the new software markedly decreased relative to RSMY1 using the old software. In case of showing trailing growth, the new software of RAISUS made it possible to choice the correct MICs and to put up the sign of trailing growth on the result screen. New software of RAISUS enhances its usability and the accuracy of MICs. Using automatic instrument to determine MICs is useful to obtain objective results easily.

Software reliability and safety in nuclear reactor protection systems

Energy Technology Data Exchange (ETDEWEB)

Lawrence, J.D. [Lawrence Livermore National Lab., CA (United States)

1993-11-01

Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor.

Software reliability and safety in nuclear reactor protection systems

International Nuclear Information System (INIS)

Lawrence, J.D.

1993-11-01

Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor

Software Configurable Multichannel Transceiver

Science.gov (United States)

Freudinger, Lawrence C.; Cornelius, Harold; Hickling, Ron; Brooks, Walter

2009-01-01

Emerging test instrumentation and test scenarios increasingly require network communication to manage complexity. Adapting wireless communication infrastructure to accommodate challenging testing needs can benefit from reconfigurable radio technology. A fundamental requirement for a software-definable radio system is independence from carrier frequencies, one of the radio components that to date has seen only limited progress toward programmability. This paper overviews an ongoing project to validate the viability of a promising chipset that performs conversion of radio frequency (RF) signals directly into digital data for the wireless receiver and, for the transmitter, converts digital data into RF signals. The Software Configurable Multichannel Transceiver (SCMT) enables four transmitters and four receivers in a single unit the size of a commodity disk drive, programmable for any frequency band between 1 MHz and 6 GHz.

History of the CERN Web Software Public Releases

CERN Document Server

Fluckiger, Francois; CERN. Geneva. IT Department

2016-01-01

This note is an extended version of the article “Licencing the Web” (http://home.web.cern.ch/topics/birthweb/licensing-web) published by CERN, Nov 2013, in the “Birth of the Web” series of articles (http://home.cern/topics/birth-web). It describes the successive steps of the public release of the CERN Web software, from public domain to open source, and explains their rationale. It provides in annexes historical documents including release announcement and texts of the licences used by CERN and MIT in public software distributions.

Measuring Software Test Verification for Complex Workpieces based on Virtual Gear Measuring Instrument

Directory of Open Access Journals (Sweden)

Yin Peili

2017-08-01

Full Text Available Validity and correctness test verification of the measuring software has been a thorny issue hindering the development of Gear Measuring Instrument (GMI. The main reason is that the software itself is difficult to separate from the rest of the measurement system for independent evaluation. This paper presents a Virtual Gear Measuring Instrument (VGMI to independently validate the measuring software. The triangular patch model with accurately controlled precision was taken as the virtual workpiece and a universal collision detection model was established. The whole process simulation of workpiece measurement is implemented by VGMI replacing GMI and the measuring software is tested in the proposed virtual environment. Taking involute profile measurement procedure as an example, the validity of the software is evaluated based on the simulation results; meanwhile, experiments using the same measuring software are carried out on the involute master in a GMI. The experiment results indicate a consistency of tooth profile deviation and calibration results, thus verifying the accuracy of gear measuring system which includes the measurement procedures. It is shown that the VGMI presented can be applied in the validation of measuring software, providing a new ideal platform for testing of complex workpiece-measuring software without calibrated artifacts.

Software for hydrogeologic time series analysis, interfacing data with physical insight

NARCIS (Netherlands)

Asmuth, Jos R. von; Maas, K.; Knotters, M.; Bierkens, M.F.P.; Bakker, M.; Olsthoorn, T.; Cirkel, D.; Leunk, I.; Schaars, F.; Asmuth, Daniel C. von

2012-01-01

The program Menyanthes combines a variety of functions for managing, editing, visualizing, analyzing and modeling hydrogeologic time series. Menyanthes was initially developed within the scope of the PhD research of the first author, whose primary aimwas the integration of data and

Real World Software Engineering

Science.gov (United States)

1994-07-15

You put the new kid there and their first promotion is out of maintenance. ii Maintenance is not sufficiently emphasized as an important criteria for...the successful material from Koffman’s CS1 pedagogy with a software-engineering-oriented Ada presentation order. Packages are introduced early and...Shumate, K. Understanding Ada. 2nd edition, John Wiley & Sons. This would make a CS1 book if it included more overall pedagogy , independent of language

Software and Network Engineering

CERN Document Server

2012-01-01

The series "Studies in Computational Intelligence" (SCI) publishes new developments and advances in the various areas of computational intelligence – quickly and with a high quality. The intent is to cover the theory, applications, and design methods of computational intelligence, as embedded in the fields of engineering, computer science, physics and life science, as well as the methodologies behind them. The series contains monographs, lecture notes and edited volumes in computational intelligence spanning the areas of neural networks, connectionist systems, genetic algorithms, evolutionary computation, artificial intelligence, cellular automata, self-organizing systems, soft computing, fuzzy systems, and hybrid intelligent systems. Critical to both contributors and readers are the short publication time and world-wide distribution - this permits a rapid and broad dissemination of research results.   The purpose of the first ACIS International Symposium on Software and Network Engineering held on Decembe...

A Description of the Software Element of the NASA EME Flight Tests

Science.gov (United States)

Koppen, Sandra V.

1996-01-01

In support of NASA's Fly-By-Light/Power-By-Wire (FBL/PBW) program, a series of flight tests were conducted by NASA Langley Research Center in February, 1995. The NASA Boeing 757 was flown past known RF transmitters to measure both external and internal radiated fields. The aircraft was instrumented with strategically located sensors for acquiring data on shielding effectiveness and internal coupling. The data are intended to support computational and statistical modeling codes used to predict internal field levels of an electromagnetic environment (EME) on aircraft. The software was an integral part of the flight tests, as well as the data reduction process. The software, which provided flight test instrument control, data acquisition, and a user interface, executes on a Hewlett Packard (HP) 300 series workstation and uses BP VEEtest development software and the C programming language. Software tools were developed for data processing and analysis, and to provide a database organized by frequency bands, test runs, and sensors. This paper describes the data acquisition system on board the aircraft and concentrates on the software portion. Hardware and software interfaces are illustrated and discussed. Particular attention is given to data acquisition and data format. The data reduction process is discussed in detail to provide insight into the characteristics, quality, and limitations of the data. An analysis of obstacles encountered during the data reduction process is presented.

EMMA: a new paradigm in configurable software

International Nuclear Information System (INIS)

Nogiec, J. M.; Trombly-Freytag, K.

2017-01-01

EMMA is a framework designed to create a family of configurable software systems, with emphasis on extensibility and flexibility. It is based on a loosely coupled, event driven architecture. The EMMA framework has been built upon the premise of composing software systems from independent components. It opens up opportunities for reuse of components and their functionality and composing them together in many different ways. As a result, it provides the developer of test and measurement applications with a lightweight alternative to microservices, while sharing their various advantages, including composability, loose coupling, encapsulation, and reuse.

EMMA: a new paradigm in configurable software

Science.gov (United States)

Nogiec, J. M.; Trombly-Freytag, K.

2017-10-01

EMMA is a framework designed to create a family of configurable software systems, with emphasis on extensibility and flexibility. It is based on a loosely coupled, event driven architecture. The EMMA framework has been built upon the premise of composing software systems from independent components. It opens up opportunities for reuse of components and their functionality and composing them together in many different ways. It provides the developer of test and measurement applications with a lightweight alternative to microservices, while sharing their various advantages, including composability, loose coupling, encapsulation, and reuse.

Handbook of Software Engineering and Knowledge Engineering

CERN Document Server

2001-01-01

This is the first handbook to cover comprehensively both software engineering and knowledge engineering - two important fields that have become interwoven in recent years. Over 60 international experts have contributed to the book. Each chapter has been written in such a way that a practitioner of software engineering and knowledge engineering can easily understand and obtain useful information. Each chapter covers one topic and can be read independently of other chapters, providing both a general survey of the topic and an in-depth exposition of the state of the art.

Multinomial-exponential reliability function: a software reliability model

International Nuclear Information System (INIS)

Saiz de Bustamante, Amalio; Saiz de Bustamante, Barbara

2003-01-01

The multinomial-exponential reliability function (MERF) was developed during a detailed study of the software failure/correction processes. Later on MERF was approximated by a much simpler exponential reliability function (EARF), which keeps most of MERF mathematical properties, so the two functions together makes up a single reliability model. The reliability model MERF/EARF considers the software failure process as a non-homogeneous Poisson process (NHPP), and the repair (correction) process, a multinomial distribution. The model supposes that both processes are statistically independent. The paper discusses the model's theoretical basis, its mathematical properties and its application to software reliability. Nevertheless it is foreseen model applications to inspection and maintenance of physical systems. The paper includes a complete numerical example of the model application to a software reliability analysis

Cross-instrument Analysis Correlation Software

Energy Technology Data Exchange (ETDEWEB)

2017-06-28

This program has been designed to assist with the tracking of a sample from one analytical instrument to another such as SEM, microscopes, micro x-ray diffraction and other instruments where particular positions/locations on the sample are examined, photographed, etc. The software is designed to easily enter the position of fiducials and locations of interest such that in a future session in the same of different instrument the positions of interest can be re-found through using the known location fiducials in the current and reference session to transform the point into the current sessions coordinate system. The software is dialog box driven guiding the user through the necessary data entry and program choices. Information is stored in a series of text based extensible markup language (XML) files.

Technical Evaluation Report 24: Open Source Software: an alternative to costly Learning Management Systems

Directory of Open Access Journals (Sweden)

Jim Depow

2003-10-01

Full Text Available This is the first in a series of two reports discussing the use of open source software (OSS and free software (FS in online education as an alternative to expensive proprietary software. It details the steps taken in a Canadian community college to download and install the Linux Operating System in order to support an OSS/ FS learning management system (LMS.

Generic Accounting and Reporting Software for Research Reactors

International Nuclear Information System (INIS)

Jaernry, C.

2010-01-01

This poster will give a general description of a generic accounting and reporting software for research reactors. The program has been designed to be a powerful working tool for the operator. The software is designed to be extremely easy to handle and at the same time give the operator the maximal power of searches, calculations and reports that a modern advanced system can produce. The systems are designed to take make the relevant accountancy for the site and perform the reporting to IAEA in Code 10. Generic software for accounting and reporting for research and other smaller facilities is something that has been asked for by many parties. Software like this could be distributed to facilities in need of a powerful accountancy and reporting system for a much lower cost than the systems that is now custom made for these facilities. This will greatly increase the quality of accountancy at these facilities and the quality of the reporting to IAEA and other state offices etc. The software is based on our advanced custom made software series 'STAR' that has been in use in many places for more than a decade with successful use. (author)

Software safety analysis on the model specified by NuSCR and SMV input language at requirements phase of software development life cycle using SMV

International Nuclear Information System (INIS)

Koh, Kwang Yong; Seong, Poong Hyun

2005-01-01

Safety-critical software process is composed of development process, verification and validation (V and V) process and safety analysis process. Safety analysis process has been often treated as an additional process and not found in a conventional software process. But software safety analysis (SSA) is required if software is applied to a safety system, and the SSA shall be performed independently for the safety software through software development life cycle (SDLC). Of all the phases in software development, requirements engineering is generally considered to play the most critical role in determining the overall software quality. NASA data demonstrate that nearly 75% of failures found in operational software were caused by errors in the requirements. The verification process in requirements phase checks the correctness of software requirements specification, and the safety analysis process analyzes the safety-related properties in detail. In this paper, the method for safety analysis at requirements phase of software development life cycle using symbolic model verifier (SMV) is proposed. Hazard is discovered by hazard analysis and in other to use SMV for the safety analysis, the safety-related properties are expressed by computation tree logic (CTL)

SOFTWARE OPEN SOURCE, SOFTWARE GRATIS?

Directory of Open Access Journals (Sweden)

Nur Aini Rakhmawati

2006-01-01

Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 Berlakunya Undang – undang Hak Atas Kekayaan Intelektual (HAKI, memunculkan suatu alternatif baru untuk menggunakan software open source. Penggunaan software open source menyebar seiring dengan isu global pada Information Communication Technology (ICT saat ini. Beberapa organisasi dan perusahaan mulai menjadikan software open source sebagai pertimbangan. Banyak konsep mengenai software open source ini. Mulai dari software yang gratis sampai software tidak berlisensi. Tidak sepenuhnya isu software open source benar, untuk itu perlu dikenalkan konsep software open source mulai dari sejarah, lisensi dan bagaimana cara memilih lisensi, serta pertimbangan dalam memilih software open source yang ada. Kata kunci :Lisensi, Open Source, HAKI

PINT, A Modern Software Package for Pulsar Timing

Science.gov (United States)

Luo, Jing; Ransom, Scott M.; Demorest, Paul; Ray, Paul S.; Stovall, Kevin; Jenet, Fredrick; Ellis, Justin; van Haasteren, Rutger; Bachetti, Matteo; NANOGrav PINT developer team

2018-01-01

Pulsar timing, first developed decades ago, has provided an extremely wide range of knowledge about our universe. It has been responsible for many important discoveries, such as the discovery of the first exoplanet and the orbital period decay of double neutron star systems. Currently pulsar timing is the leading technique for detecting low frequency (about 10^-9 Hertz) gravitational waves (GW) using an array of pulsars as the detectors. To achieve this goal, high precision pulsar timing data, at about nanoseconds level, is required. Most high precision pulsar timing data are analyzed using the widely adopted software TEMPO/TEMPO2. But for a robust and believable GW detection, it is important to have independent software that can cross-check the result. In this poster we present the new generation pulsar timing software PINT. This package will provide a robust system to cross check high-precision timing results, completely independent of TEMPO and TEMPO2. In addition, PINT is designed to be a package that is easy to extend and modify, through use of flexible code architecture and a modern programming language, Python, with modern technology and libraries.

CONSIDERACIONES RELACIONADAS CON LAS INSPECCIONES DE SOFTWARE

Directory of Open Access Journals (Sweden)

Bexy Alfonso Espinosa

2006-04-01

Full Text Available

The BTeV Software Tutorial Suite

International Nuclear Information System (INIS)

Kutschke, Robert K.

2004-01-01

The BTeV Collaboration is starting to develop its C++ based offline software suite, an integral part of which is a series of tutorials. These tutorials are targeted at a diverse audience, including new graduate students, experienced physicists with little or no C++ experience, those with just enough C++ to be dangerous, and experts who need only an overview of the available tools. The tutorials must both teach C++ in general and the BTeV specific tools in particular. Finally, they must teach physicists how to find and use the detailed documentation. This report will review the status of the BTeV experiment, give an overview of the plans for and the state of the software and will then describe the plans for the tutorial suite

A CONCEPT OF SOFTWARE SUPPORT OF LEARNING PROGRAMMING LANGUAGE AND TECHNOLOGIES

Directory of Open Access Journals (Sweden)

V. Kruglyk

2013-03-01

Full Text Available A concept of software support of learning programming language and technologies is regarded in the article. Present systems of independent study of subjects, related to programming, are examined. Necessary components of a system of support learning programming languages and technologies, which is oriented on independent study, are considered.

Development of interactive software for fuel management analysis

International Nuclear Information System (INIS)

Graves, H.W. Jr.

1986-01-01

Electronic computation plays a central part in engineering analysis of all types. Utilization of microcomputers for calculations that were formerly carried out on large mainframe computers presents a unique opportunity to develop software that not only takes advantage of the lower cost of using these machines, but also increases the efficiency of the engineers performing these calculations. This paper reviews the use of electronic computers in engineering analysis, discusses the potential for microcomputer utilization in this area, and describes a series of steps to be followed in software development that can yield significant gains in engineering design efficiency

4th International Conference in Software Engineering for Defence Applications

CERN Document Server

Sillitti, Alberto; Succi, Giancarlo; Messina, Angelo

2016-01-01

This book presents high-quality original contributions on new software engineering models, approaches, methods, and tools and their evaluation in the context of defence and security applications. In addition, important business and economic aspects are discussed, with a particular focus on cost/benefit analysis, new business models, organizational evolution, and business intelligence systems. The contents are based on presentations delivered at SEDA 2015, the 4th International Conference in Software Engineering for Defence Applications, which was held in Rome, Italy, in May 2015. This conference series represents a targeted response to the growing need for research that reports and debates the practical implications of software engineering within the defence environment and also for software performance evaluation in real settings through controlled experiments as well as case and field studies. The book will appeal to all with an interest in modeling, managing, and implementing defence-related software devel...

Statistical Software and Artificial Intelligence: A Watershed in Applications Programming.

Science.gov (United States)

Pickett, John C.

1984-01-01

AUTOBJ and AUTOBOX are revolutionary software programs which contain the first application of artificial intelligence to statistical procedures used in analysis of time series data. The artificial intelligence included in the programs and program features are discussed. (JN)

An open-source software package for multivariate modeling and clustering: applications to air quality management.

Science.gov (United States)

Wang, Xiuquan; Huang, Guohe; Zhao, Shan; Guo, Junhong

2015-09-01

This paper presents an open-source software package, rSCA, which is developed based upon a stepwise cluster analysis method and serves as a statistical tool for modeling the relationships between multiple dependent and independent variables. The rSCA package is efficient in dealing with both continuous and discrete variables, as well as nonlinear relationships between the variables. It divides the sample sets of dependent variables into different subsets (or subclusters) through a series of cutting and merging operations based upon the theory of multivariate analysis of variance (MANOVA). The modeling results are given by a cluster tree, which includes both intermediate and leaf subclusters as well as the flow paths from the root of the tree to each leaf subcluster specified by a series of cutting and merging actions. The rSCA package is a handy and easy-to-use tool and is freely available at http://cran.r-project.org/package=rSCA . By applying the developed package to air quality management in an urban environment, we demonstrate its effectiveness in dealing with the complicated relationships among multiple variables in real-world problems.

The SE Book: Principles and Techniques of Software Engineering or orAn ABZ of The Theory & Practice of Software Engineering

DEFF Research Database (Denmark)

Bjørner, Dines

) the TripTych of domain analysis, requirements engineering and software design -- and much much more. It relates all aspects of (12) platform technologies, (13) legal issues of software, (14) quality assurance, and (15) project and product management to the above (1-11 incl.). Highlights of the book series......This ``epos'' emphasises (1) software development from both a formal and an informal approach; (2) the use of mathematics, logic and algebras, as well as discrete mathematics: Sets, Cartesians, lists, functions, maps; (3) property as well as model-oriented specifications; (4) semiotics in the form...... are: (A) Emphasis on design: Literally a thousand development examples are given; and on ``Calculi'' of (B) domain and (C) requirements engineering: Domain facet ``operators'' like: (d.1) Instrinsics, (d.2) support technology, (d.3) management & organisation, (d.4) rules & regulations, (d.5) human...

A Component-Oriented Programming for Embedded Mobile Robot Software

Directory of Open Access Journals (Sweden)

Safaai Deris

2008-11-01

Full Text Available Applying software reuse to many Embedded Real-Time (ERT systems poses significant challenges to industrial software processes due to the resource-constrained and real-time requirements of the systems. Autonomous Mobile Robot (AMR system is a class of ERT systems, hence, inherits the challenge of applying software reuse in general ERT systems. Furthermore, software reuse in AMR systems is challenged by the diversities in terms of robot physical size and shape, environmental interaction and implementation platform. Thus, it is envisioned that component-based software engineering will be the suitable way to promote software reuse in AMR systems with consideration to general requirements to be self-contained, platform-independent and real-time predictable. A framework for component-oriented programming for AMR software development using PECOS component model is proposed in this paper. The main features of this framework are: (1 use graphical representation for components definition and composition; (2 target C language for optimal code generation with resource-constrained micro-controller; and (3 minimal requirement for run-time support. Real-time implementation indicates that, the PECOS component model together with the proposed framework is suitable for resource constrained embedded AMR systems software development.

Generation of Controlled Analog Emissions from Embedded Devices using Software Stress Methods

Science.gov (United States)

2017-03-01

Hardware and Software Tools HARDWARE Device Model Software Defined Radio USRP N210 EMC Probes 100 Series EMC Probe amplifier 105A Development...shown in Fig. 8 as waterfall (top) and logic plots (bottom). Figure 7: Sequence for inducing string emission Figure 8: Reconstruction...of the ‘00011001001’ in waterfall (top) and logic (bottom) plots transmitted using square root operations Conclusion This paper presented a method

Usage models in reliability assessment of software-based systems

Energy Technology Data Exchange (ETDEWEB)

Haapanen, P.; Pulkkinen, U. [VTT Automation, Espoo (Finland); Korhonen, J. [VTT Electronics, Espoo (Finland)

1997-04-01

This volume in the OHA-project report series deals with the statistical reliability assessment of software based systems on the basis of dynamic test results and qualitative evidence from the system design process. Other reports to be published later on in the OHA-project report series will handle the diversity requirements in safety critical software-based systems, generation of test data from operational profiles and handling of programmable automation in plant PSA-studies. In this report the issues related to the statistical testing and especially automated test case generation are considered. The goal is to find an efficient method for building usage models for the generation of statistically significant set of test cases and to gather practical experiences from this method by applying it in a case study. The scope of the study also includes the tool support for the method, as the models may grow quite large and complex. (32 refs., 30 figs.).

Usage models in reliability assessment of software-based systems

International Nuclear Information System (INIS)

Haapanen, P.; Pulkkinen, U.; Korhonen, J.

1997-04-01

This volume in the OHA-project report series deals with the statistical reliability assessment of software based systems on the basis of dynamic test results and qualitative evidence from the system design process. Other reports to be published later on in the OHA-project report series will handle the diversity requirements in safety critical software-based systems, generation of test data from operational profiles and handling of programmable automation in plant PSA-studies. In this report the issues related to the statistical testing and especially automated test case generation are considered. The goal is to find an efficient method for building usage models for the generation of statistically significant set of test cases and to gather practical experiences from this method by applying it in a case study. The scope of the study also includes the tool support for the method, as the models may grow quite large and complex. (32 refs., 30 figs.)

The Little Giant: The IBM Series/1 in Library Applications.

Science.gov (United States)

Hendricks, Donald D.; Manino, Glenn

1987-01-01

This description of the use of IBM Series/1 minicomputers to implement a library automation system includes discussion of current functions of the system, the system configuration, communications capabilities, software, and cost factors. (CLB)

Tool Use Within NASA Software Quality Assurance

Science.gov (United States)

Shigeta, Denise; Port, Dan; Nikora, Allen P.; Wilf, Joel

2013-01-01

As space mission software systems become larger and more complex, it is increasingly important for the software assurance effort to have the ability to effectively assess both the artifacts produced during software system development and the development process itself. Conceptually, assurance is a straightforward idea - it is the result of activities carried out by an organization independent of the software developers to better inform project management of potential technical and programmatic risks, and thus increase management's confidence in the decisions they ultimately make. In practice, effective assurance for large, complex systems often entails assessing large, complex software artifacts (e.g., requirements specifications, architectural descriptions) as well as substantial amounts of unstructured information (e.g., anomaly reports resulting from testing activities during development). In such an environment, assurance engineers can benefit greatly from appropriate tool support. In order to do so, an assurance organization will need accurate and timely information on the tool support available for various types of assurance activities. In this paper, we investigate the current use of tool support for assurance organizations within NASA, and describe on-going work at JPL for providing assurance organizations with the information about tools they need to use them effectively.

User's Guide, software for reduction and analysis of daily weather and surface-water data: Tools for time series analysis of precipitation, temperature, and streamflow data

Science.gov (United States)

Hereford, Richard

2006-01-01

The software described here is used to process and analyze daily weather and surface-water data. The programs are refinements of earlier versions that include minor corrections and routines to calculate frequencies above a threshold on an annual or seasonal basis. Earlier versions of this software were used successfully to analyze historical precipitation patterns of the Mojave Desert and the southern Colorado Plateau regions, ecosystem response to climate variation, and variation of sediment-runoff frequency related to climate (Hereford and others, 2003; 2004; in press; Griffiths and others, 2006). The main program described here (Day_Cli_Ann_v5.3) uses daily data to develop a time series of various statistics for a user specified accounting period such as a year or season. The statistics include averages and totals, but the emphasis is on the frequency of occurrence in days of relatively rare weather or runoff events. These statistics are indices of climate variation; for a discussion of climate indices, see the Climate Research Unit website of the University of East Anglia (http://www.cru.uea.ac.uk/projects/stardex/) and the Climate Change Indices web site (http://cccma.seos.uvic.ca/ETCCDMI/indices.html). Specifically, the indices computed with this software are the frequency of high intensity 24-hour rainfall, unusually warm temperature, and unusually high runoff. These rare, or extreme events, are those greater than the 90th percentile of precipitation, streamflow, or temperature computed for the period of record of weather or gaging stations. If they cluster in time over several decades, extreme events may produce detectable change in the physical landscape and ecosystem of a given region. Although the software has been tested on a variety of data, as with any software, the user should carefully evaluate the results with their data. The programs were designed for the range of precipitation, temperature, and streamflow measurements expected in the semiarid

Approaches in highly parameterized inversion: TSPROC, a general time-series processor to assist in model calibration and result summarization

Science.gov (United States)

Westenbroek, Stephen M.; Doherty, John; Walker, John F.; Kelson, Victor A.; Hunt, Randall J.; Cera, Timothy B.

2012-01-01

The TSPROC (Time Series PROCessor) computer software uses a simple scripting language to process and analyze time series. It was developed primarily to assist in the calibration of environmental models. The software is designed to perform calculations on time-series data commonly associated with surface-water models, including calculation of flow volumes, transformation by means of basic arithmetic operations, and generation of seasonal and annual statistics and hydrologic indices. TSPROC can also be used to generate some of the key input files required to perform parameter optimization by means of the PEST (Parameter ESTimation) computer software. Through the use of TSPROC, the objective function for use in the model-calibration process can be focused on specific components of a hydrograph.

Verification of operating software for cooperative monitoring applications

International Nuclear Information System (INIS)

Tolk, K.M.; Rembold, R.K.

1997-01-01

Monitoring agencies often use computer based equipment to control instruments and to collect data at sites that are being monitored under international safeguards or other cooperative monitoring agreements. In order for this data to be used as an independent verification of data supplied by the host at the facility, the software used must be trusted by the monitoring agency. The monitoring party must be sure that the software has not be altered to give results that could lead to erroneous conclusions about nuclear materials inventories or other operating conditions at the site. The host might also want to verify that the software being used is the software that has been previously inspected in order to be assured that only data that is allowed under the agreement is being collected. A description of a method to provide this verification using keyed has functions and how the proposed method overcomes possible vulnerabilities in methods currently in use such as loading the software from trusted disks is presented. The use of public key data authentication for this purpose is also discussed

Programmable pulse series generator for NMR relaxometer

International Nuclear Information System (INIS)

Stolbunov, R.N.; Chichikov, S.A.; Lundin, A.G.

2005-01-01

Paper describes a pulse series generator for NMR relaxometer. The operation mode is set on the basis of the PC program by the PCI bus in the internal memory. The design is based on two Altera Company MAX7000S and Cyclone family microcircuits using the Qartus II 4.0 software. The basic parameters are as follows: pulse minimum length - 50 ns, time resolution - 10 ns, pulse maximum number - 1024, number of controlled output channels - 8. The designed device as a part of the NMR hardware-software system enables to record, to process and to store the experiment results in the form of electronic document [ru

Mathis software for controlling BCAM-based monitoring and alignment systems

CERN Document Server

Klumb, Francis; Kautzmann, Guillaume; CERN. Geneva. ATS Department

2016-01-01

The MATHIS Software (Monitoring and Alignment Tracking for HIE-Isolde Software) aims at providing 3D positions of physical components of the HIE-Isolde superconducting modules, accurately and permanently measured by well-designed networks of BCAM devices (Brandeis Camera Angle Monitoring). Although it is originally intended for the HIE-Isolde project, its architecture and its use cases have been extended and optimized for more general setups. Most of the configuration data are stored either within XML-formatted files or within databases. The adaptation of MATHIS for different BCAM monitoring systems therefore does not require any further code rewriting. Moreover, the software is fully cross-platform and can either be run on the specific Linux machines driving the accelerator electronic devices, or be used on independent Windows workstations as a stand-alone software. In the first case, the software mainly relies on FESA (Front End Software Architecture) which is an object-oriented real-time framework that ens...

A federated design for a neurobiological simulation engine: the CBI federated software architecture.

Directory of Open Access Journals (Sweden)

Hugo Cornelis

Full Text Available Simulator interoperability and extensibility has become a growing requirement in computational biology. To address this, we have developed a federated software architecture. It is federated by its union of independent disparate systems under a single cohesive view, provides interoperability through its capability to communicate, execute programs, or transfer data among different independent applications, and supports extensibility by enabling simulator expansion or enhancement without the need for major changes to system infrastructure. Historically, simulator interoperability has relied on development of declarative markup languages such as the neuron modeling language NeuroML, while simulator extension typically occurred through modification of existing functionality. The software architecture we describe here allows for both these approaches. However, it is designed to support alternative paradigms of interoperability and extensibility through the provision of logical relationships and defined application programming interfaces. They allow any appropriately configured component or software application to be incorporated into a simulator. The architecture defines independent functional modules that run stand-alone. They are arranged in logical layers that naturally correspond to the occurrence of high-level data (biological concepts versus low-level data (numerical values and distinguish data from control functions. The modular nature of the architecture and its independence from a given technology facilitates communication about similar concepts and functions for both users and developers. It provides several advantages for multiple independent contributions to software development. Importantly, these include: (1 Reduction in complexity of individual simulator components when compared to the complexity of a complete simulator, (2 Documentation of individual components in terms of their inputs and outputs, (3 Easy removal or replacement of

Portable software for distributed readout controllers and event builders in FASTBUS and VME

International Nuclear Information System (INIS)

Pordes, R.; Berg, D.; Berman, E.; Bernett, M.; Brown, D.; Constanta-Fanourakis, P.; Dorries, T.; Haire, M.; Joshi, U.; Kaczar, K.; Mackinnon, B.; Moore, C.; Nicinski, T.; Oleynik, G.; Petravick, D.; Sergey, G.; Slimmer, D.; Streets, J.; Votava, M.; White, V.

1989-12-01

We report on software developed as part of the PAN-DA system to support the functions of front end readout controllers and event builders in multiprocessor, multilevel, distributed data acquisition systems. For the next generation data acquisition system we have undertaken to design and implement software tools that are easily transportable to new modules. The first implementation of this software is for Motorola 68K series processor boards in FASTBUS and VME and will be used in the Fermilab accelerator run at the beginning of 1990. We use a Real Time Kernel Operating System. The software provides general connectivity tools for control, diagnosis and monitoring. 17 refs., 7 figs

Measurement-device-independent quantum digital signatures

Science.gov (United States)

Puthoor, Ittoop Vergheese; Amiri, Ryan; Wallden, Petros; Curty, Marcos; Andersson, Erika

2016-08-01

Digital signatures play an important role in software distribution, modern communication, and financial transactions, where it is important to detect forgery and tampering. Signatures are a cryptographic technique for validating the authenticity and integrity of messages, software, or digital documents. The security of currently used classical schemes relies on computational assumptions. Quantum digital signatures (QDS), on the other hand, provide information-theoretic security based on the laws of quantum physics. Recent work on QDS Amiri et al., Phys. Rev. A 93, 032325 (2016);, 10.1103/PhysRevA.93.032325 Yin, Fu, and Zeng-Bing, Phys. Rev. A 93, 032316 (2016), 10.1103/PhysRevA.93.032316 shows that such schemes do not require trusted quantum channels and are unconditionally secure against general coherent attacks. However, in practical QDS, just as in quantum key distribution (QKD), the detectors can be subjected to side-channel attacks, which can make the actual implementations insecure. Motivated by the idea of measurement-device-independent quantum key distribution (MDI-QKD), we present a measurement-device-independent QDS (MDI-QDS) scheme, which is secure against all detector side-channel attacks. Based on the rapid development of practical MDI-QKD, our MDI-QDS protocol could also be experimentally implemented, since it requires a similar experimental setup.

Introduction to time series and forecasting

CERN Document Server

Brockwell, Peter J

2016-01-01

This book is aimed at the reader who wishes to gain a working knowledge of time series and forecasting methods as applied to economics, engineering and the natural and social sciences. It assumes knowledge only of basic calculus, matrix algebra and elementary statistics. This third edition contains detailed instructions for the use of the professional version of the Windows-based computer package ITSM2000, now available as a free download from the Springer Extras website. The logic and tools of time series model-building are developed in detail. Numerous exercises are included and the software can be used to analyze and forecast data sets of the user's own choosing. The book can also be used in conjunction with other time series packages such as those included in R. The programs in ITSM2000 however are menu-driven and can be used with minimal investment of time in the computational details. The core of the book covers stationary processes, ARMA and ARIMA processes, multivariate time series and state-space mod...

EFOM 12C software: general overview. Final report

Energy Technology Data Exchange (ETDEWEB)

Jadot, P; Fuchsova, J; Vankelecom, E; Van der Voort, E; Thonet, C

1981-01-01

A logic manual defining the general philosophy of the EC-12C software is presented. The guidelines used to develop the Energy Data Base and the programs of the energy flow models are: within the frame of some basic conventions, the data base structure and software should be as independent as possible from the energy system representation; utilization of the models should be user-friendly; as data has to be collected and manipulated by various national expert teams, extensive data consistency checks and appropriate error messages should be included in the software to support the data validation process; the various energy flow models should be integrated; the outputs of the programs should be user-controlled; and the scope of the study is under user's control. As a result of those guidelines, an integrated set of software composed of DAMOCLES (Data Base Management System); SIML (simulation program suitable for data analysis and description study); and ORESTE EDISON (LP matrix generator and report writer) was developed. These are described.

Guidance and Control Software Project Data - Volume 1: Planning Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the planning documents from the GCS project. Volume 1 contains five appendices: A. Plan for Software Aspects of Certification for the Guidance and Control Software Project; B. Software Development Standards for the Guidance and Control Software Project; C. Software Verification Plan for the Guidance and Control Software Project; D. Software Configuration Management Plan for the Guidance and Control Software Project; and E. Software Quality Assurance Activities.

Class 1E software verification and validation: Past, present, and future

Energy Technology Data Exchange (ETDEWEB)

Persons, W.L.; Lawrence, J.D.

1993-10-01

This paper discusses work in progress that addresses software verification and validation (V&V) as it takes place during the full software life cycle of safety-critical software. The paper begins with a brief overview of the task description and discussion of the historical evolution of software V&V. A new perspective is presented which shows the entire verification and validation process from the viewpoints of a software developer, product assurance engineer, independent V&V auditor, and government regulator. An account of the experience of the field test of the Verification Audit Plan and Report generated from the V&V Guidelines is presented along with sample checklists and lessons learned from the verification audit experience. Then, an approach to automating the V&V Guidelines is introduced. The paper concludes with a glossary and bibliography.

Software Quality Assurance for Nuclear Safety Systems

International Nuclear Information System (INIS)

Sparkman, D R; Lagdon, R

2004-01-01

The US Department of Energy has undertaken an initiative to improve the quality of software used to design and operate their nuclear facilities across the United States. One aspect of this initiative is to revise or create new directives and guides associated with quality practices for the safety software in its nuclear facilities. Safety software includes the safety structures, systems, and components software and firmware, support software and design and analysis software used to ensure the safety of the facility. DOE nuclear facilities are unique when compared to commercial nuclear or other industrial activities in terms of the types and quantities of hazards that must be controlled to protect workers, public and the environment. Because of these differences, DOE must develop an approach to software quality assurance that ensures appropriate risk mitigation by developing a framework of requirements that accomplishes the following goals: (sm b ullet) Ensures the software processes developed to address nuclear safety in design, operation, construction and maintenance of its facilities are safe (sm b ullet) Considers the larger system that uses the software and its impacts (sm b ullet) Ensures that the software failures do not create unsafe conditions Software designers for nuclear systems and processes must reduce risks in software applications by incorporating processes that recognize, detect, and mitigate software failure in safety related systems. It must also ensure that fail safe modes and component testing are incorporated into software design. For nuclear facilities, the consideration of risk is not necessarily sufficient to ensure safety. Systematic evaluation, independent verification and system safety analysis must be considered for software design, implementation, and operation. The software industry primarily uses risk analysis to determine the appropriate level of rigor applied to software practices. This risk-based approach distinguishes safety

Software Agents Applications Using Real-Time CORBA

Science.gov (United States)

Fowell, S.; Ward, R.; Nielsen, M.

This paper describes current projects being performed by SciSys in the area of the use of software agents, built using CORBA middleware, to improve operations within autonomous satellite/ground systems. These concepts have been developed and demonstrated in a series of experiments variously funded by ESA's Technology Flight Opportunity Initiative (TFO) and Leading Edge Technology for SMEs (LET-SME), and the British National Space Centre's (BNSC) National Technology Programme. Some of this earlier work has already been reported in [1]. This paper will address the trends, issues and solutions associated with this software agent architecture concept, together with its implementation using CORBA within an on-board environment, that is to say taking account of its real- time and resource constrained nature.

A handbook of software and systems engineering empirical observations, laws and theories

CERN Document Server

Endres, Albert

2003-01-01

This book is intended as a handbook for students and practitioners alike. The book is structured around the type of tasks that practitioners are confronted with, beginning with requirements definition and concluding with maintenance and withdrawal. It identifies and discusses existing laws that have a significant impact on the software engineering field. These laws are largely independent of the technologies involved, which allow students to learn the principles underlying software engineering. This also guides students toward the best practice when implementing software engineering techniques.

Genealogical series method. Hyperpolar points screen effect

International Nuclear Information System (INIS)

Gorbatov, A.M.

1991-01-01

The fundamental values of the genealogical series method -the genealogical integrals (sandwiches) have been investigated. The hyperpolar points screen effect has been found. It allows one to calculate the sandwiches for the Fermion systems with large number of particles and to ascertain the validity of the iterated-potential method as well. For the first time the genealogical-series method has been realized numerically for the central spin-independent potential

Application of a methodology for the development and validation of reliable process control software

International Nuclear Information System (INIS)

Ramamoorthy, C.V.; Mok, Y.R.; Bastani, F.B.; Chin, G.

1980-01-01

The necessity of a good methodology for the development of reliable software, especially with respect to the final software validation and testing activities, is discussed. A formal specification development and validation methodology is proposed. This methodology has been applied to the development and validation of a pilot software, incorporating typical features of critical software for nuclear power plants safety protection. The main features of the approach include the use of a formal specification language and the independent development of two sets of specifications. 1 ref

Development of a plug-in for Variability Modeling in Software Product Lines

Directory of Open Access Journals (Sweden)

María Lucía López-Araujo

2012-03-01

Full Text Available Las Líneas de Productos de Software (LPS toman ventaja económica de las similitudes y variación entre un conjunto de sistemas de software dentro de un dominio específico. La Ingeniería de Líneas de Productos de Software por lo tanto, define una serie de procesos para el desarrollo de LPS que consideran las similitudes y variación a lo largo del ciclo devida. El modelado de variabilidad, en consecuencia, es una actividad esencial en un enfoque de Ingeniería de Líneas de Productos de Software. Existen varias técnicas para modelado de variabilidad. Entre ellas resalta COVAMOF que permite modelar los puntos de variación, variantes y dependencias como entidades de primera clase, proporcionando una manera uniforme de representarlos en los diversos niveles de abstracción de una LPS. Para poder aprovechar los beneficios de COVAMOF es necesario contar con una herramienta, de otra manera el modelado y la administración de la variabilidad pueden resultar una labor ardua para el ingeniero de software. Este trabajo presenta el desarrollo de un plug-in de COVAMOF para Eclipse.Software Product Lines (SPL take economic advantage of commonality and variability among a set of software systems that exist within a specific domain. Therefore, Software Product Line Engineering defines a series of processes for the development of a SPL that consider commonality and variability during the software life cycle. Variability modeling is therefore an essential activity in a Software Product Line Engineering approach. There are several techniques for variability modeling nowadays. COVAMOF stands out among them since it allows the modeling of variation points, variants and dependencies as first class elements. COVAMOF, therefore, provides an uniform manner for representing such concepts in different levels of abstraction within a SPL. In order to take advantage of COVAMOF benefits, it is necessary to have a computer aided tool, otherwise variability modeling and

A field study on root cause analysis of defects in space software

International Nuclear Information System (INIS)

Silva, Nuno; Cunha, João Carlos; Vieira, Marco

2017-01-01

Critical systems, such as space systems, are developed under strict requirements envisaging high integrity in accordance to specific standards. For such software systems, an independent assessment is put into effect (Independent Software Verification and Validation – ISVV) after the regular development lifecycle and V&V activities, aiming at finding residual faults and raising confidence in the software. However, it has been observed that there is still a significant number of defects remaining at this stage, questioning the effectiveness of the previous engineering processes. This paper presents a root cause analysis of 1070 defects found in four space software projects during ISVV, by applying an improved Orthogonal Defect Classification (ODC) taxonomy and examining the defect types, triggers and impacts, in order to identify why they reached such a later stage in the development. The paper also puts forward proposals for modifications to both the software development (to prevent defects) and the V&V activities (to better detect defects) and an assessment methodology for future works on root cause analysis. - Highlights: • Root cause analysis of space software defects by using an enhanced ODC taxonomy. • Prioritization of the root causes according to the more important defect impacts. • Identification of improvements to systems engineering and development processes. • Improvements to V&V activities as means to reduce the occurrence of defects. • Generic process to achieve the defects root causes and the corrections suggestions.

Global Software Engineering: A Software Process Approach

Science.gov (United States)

Richardson, Ita; Casey, Valentine; Burton, John; McCaffery, Fergal

Our research has shown that many companies are struggling with the successful implementation of global software engineering, due to temporal, cultural and geographical distance, which causes a range of factors to come into play. For example, cultural, project managementproject management and communication difficulties continually cause problems for software engineers and project managers. While the implementation of efficient software processes can be used to improve the quality of the software product, published software process models do not cater explicitly for the recent growth in global software engineering. Our thesis is that global software engineering factors should be included in software process models to ensure their continued usefulness in global organisations. Based on extensive global software engineering research, we have developed a software process, Global Teaming, which includes specific practices and sub-practices. The purpose is to ensure that requirements for successful global software engineering are stipulated so that organisations can ensure successful implementation of global software engineering.

Software Users Manual (SUM): Extended Testability Analysis (ETA) Tool

Science.gov (United States)

Maul, William A.; Fulton, Christopher E.

2011-01-01

This software user manual describes the implementation and use the Extended Testability Analysis (ETA) Tool. The ETA Tool is a software program that augments the analysis and reporting capabilities of a commercial-off-the-shelf (COTS) testability analysis software package called the Testability Engineering And Maintenance System (TEAMS) Designer. An initial diagnostic assessment is performed by the TEAMS Designer software using a qualitative, directed-graph model of the system being analyzed. The ETA Tool utilizes system design information captured within the diagnostic model and testability analysis output from the TEAMS Designer software to create a series of six reports for various system engineering needs. The ETA Tool allows the user to perform additional studies on the testability analysis results by determining the detection sensitivity to the loss of certain sensors or tests. The ETA Tool was developed to support design and development of the NASA Ares I Crew Launch Vehicle. The diagnostic analysis provided by the ETA Tool was proven to be valuable system engineering output that provided consistency in the verification of system engineering requirements. This software user manual provides a description of each output report generated by the ETA Tool. The manual also describes the example diagnostic model and supporting documentation - also provided with the ETA Tool software release package - that were used to generate the reports presented in the manual

CheMentor Software System by H. A. Peoples

Science.gov (United States)

Reid, Brian P.

1997-09-01

CheMentor Software System H. A. Peoples. Computerized Learning Enhancements: http://www.ecis.com/~clehap; email: clehap@ecis.com; 1996 - 1997. CheMentor is a series of software packages for introductory-level chemistry, which includes Practice Items (I), Stoichiometry (I), Calculating Chemical Formulae, and the CheMentor Toolkit. The first three packages provide practice problems for students and various types of help to solve them; the Toolkit includes "calculators" for determining chemical quantities as well as the Practice Items (I) set of problems. The set of software packages is designed so that each individual product acts as a module of a common CheMentor program. As the name CheMentor implies, the software is designed as a "mentor" for students learning introductory chemistry concepts and problems. The typical use of the software would be by individual students (or perhaps small groups) as an adjunct to lectures. CheMentor is a HyperCard application and the modules are HyperCard stacks. The requirements to run the packages include a Macintosh computer with at least 1 MB of RAM, a hard drive with several MB of available space depending upon the packages selected (10 MB were required for all the packages reviewed here), and the Mac operating system 6.0.5 or later.

Guidance and Control Software Project Data - Volume 2: Development Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the development documents from the GCS project. Volume 2 contains three appendices: A. Guidance and Control Software Development Specification; B. Design Description for the Pluto Implementation of the Guidance and Control Software; and C. Source Code for the Pluto Implementation of the Guidance and Control Software

Protyping machine vision software on the World Wide Web

Science.gov (United States)

Karantalis, George; Batchelor, Bruce G.

1998-10-01

Interactive image processing is a proven technique for analyzing industrial vision applications and building prototype systems. Several of the previous implementations have used dedicated hardware to perform the image processing, with a top layer of software providing a convenient user interface. More recently, self-contained software packages have been devised and these run on a standard computer. The advent of the Java programming language has made it possible to write platform-independent software, operating over the Internet, or a company-wide Intranet. Thus, there arises the possibility of designing at least some shop-floor inspection/control systems, without the vision engineer ever entering the factories where they will be used. It successful, this project will have a major impact on the productivity of vision systems designers.

IMAGE information monitoring and applied graphics software environment. Volume 4. Applications description

International Nuclear Information System (INIS)

Hallam, J.W.; Ng, K.B.; Upham, G.L.

1986-09-01

The EPRI Information Monitoring and Applied Graphics Environment (IMAGE) system is designed for 'fast proto-typing' of advanced concepts for computer-aided plant operations tools. It is a flexible software system which can be used for rapidly creating, dynamically driving and evaluating advanced operator aid displays. The software is written to be both host computer and graphic device independent. This four volume report includes an Executive Overview of the IMAGE package (Volume 1), followed by Software Description (Volume II), User's Guide (Volume III), and Description of Example Applications (Volume IV)

Real-time scheduling of software tasks

International Nuclear Information System (INIS)

Hoff, L.T.

1995-01-01

When designing real-time systems, it is often desirable to schedule execution of software tasks based on the occurrence of events. The events may be clock ticks, interrupts from a hardware device, or software signals from other software tasks. If the nature of the events, is well understood, this scheduling is normally a static part of the system design. If the nature of the events is not completely understood, or is expected to change over time, it may be necessary to provide a mechanism for adjusting the scheduling of the software tasks. RHIC front-end computers (FECs) provide such a mechanism. The goals in designing this mechanism were to be as independent as possible of the underlying operating system, to allow for future expansion of the mechanism to handle new types of events, and to allow easy configuration. Some considerations which steered the design were programming paradigm (object oriented vs. procedural), programming language, and whether events are merely interesting moments in time, or whether they intrinsically have data associated with them. The design also needed to address performance and robustness tradeoffs involving shared task contexts, task priorities, and use of interrupt service routine (ISR) contexts vs. task contexts. This paper will explore these considerations and tradeoffs

Class 1E software verification and validation: Past, present, and future

International Nuclear Information System (INIS)

Persons, W.L.; Lawrence, J.D.

1993-10-01

This paper discusses work in progress that addresses software verification and validation (V ampersand V) as it takes place during the full software life cycle of safety-critical software. The paper begins with a brief overview of the task description and discussion of the historical evolution of software V ampersand V. A new perspective is presented which shows the entire verification and validation process from the viewpoints of a software developer, product assurance engineer, independent V ampersand V auditor, and government regulator. An account of the experience of the field test of the Verification Audit Plan and Report generated from the V ampersand V Guidelines is presented along with sample checklists and lessons learned from the verification audit experience. Then, an approach to automating the V ampersand V Guidelines is introduced. The paper concludes with a glossary and bibliography

Class 1E software verification and validation: Past, present, and future

International Nuclear Information System (INIS)

Persons, W.L.; Lawrence, J.D.

1994-01-01

This paper discusses work in progress that addresses software verification and validation (V ampersand V) as it takes place during the full software life cycle of safety-critical software. The paper begins with a brief overview of the task description and discussion of the historical evolution of software V ampersand V. A new perspective is presented which shows the entire verification and validation process from the viewpoints of a software developer, product assurance engineer, independent V ampersand V auditor, and government regulator. An account of the experience of the field test of the Verification Audit Plan and Report generated from the V ampersand V Guidelines is presented along with sample checklists and lessons learned from the verification audit experience. Then, an approach to automating the V ampersand V Guidelines is introduced. The paper concludes with a glossary and bibliography

Deployment of the CMS software on the WLCG Grid

International Nuclear Information System (INIS)

Behrenhoff, W; Wissing, C; Kim, B; Blyweert, S; D'Hondt, J; Maes, J; Maes, M; Mulders, P Van; Villella, I; Vanelderen, L

2011-01-01

The CMS Experiment is taking high energy collision data at CERN. The computing infrastructure used to analyse the data is distributed round the world in a tiered structure. In order to use the 7 Tier-1 sites, the 50 Tier-2 sites and a still growing number of about 30 Tier-3 sites, the CMS software has to be available at those sites. Except for a very few sites the deployment and the removal of CMS software is managed centrally. Since the deployment team has no local accounts at the remote sites all installation jobs have to be sent via Grid jobs. Via a VOMS role the job has a high priority in the batch system and gains write privileges to the software area. Due to the lack of interactive access the installation jobs must be very robust against possible failures, in order not to leave a broken software installation. The CMS software is packaged in RPMs that are installed in the software area independent of the host OS. The apt-get tool is used to resolve package dependencies. This paper reports about the recent deployment experiences and the achieved performance.

Tailorable software architectures in the accelerator control system environment

International Nuclear Information System (INIS)

Mejuev, Igor; Kumagai, Akira; Kadokura, Eiichi

2001-01-01

Tailoring is further evolution of an application after deployment in order to adapt it to requirements that were not accounted for in the original design. End-user tailorability has been extensively researched in applied computer science from HCl and software engineering perspectives. Tailorability allows coping with flexibility requirements, decreasing maintenance and development costs of software products. In general, dynamic or diverse software requirements constitute the need for implementing end-user tailorability in computer systems. In accelerator physics research the factor of dynamic requirements is especially important, due to frequent software and hardware modifications resulting in correspondingly high upgrade and maintenance costs. In this work we introduce the results of feasibility study on implementing end-user tailorability in the software for accelerator control system, considering the design and implementation of distributed monitoring application for 12 GeV KEK Proton Synchrotron as an example. The software prototypes used in this work are based on a generic tailoring platform (VEDICI), which allows decoupling of tailoring interfaces and runtime components. While representing a reusable application-independent framework, VEDICI can be potentially applied for tailoring of arbitrary compositional Web-based applications

Developing Project Duration Models in Software Engineering

Institute of Scientific and Technical Information of China (English)

Pierre Bourque; Serge Oligny; Alain Abran; Bertrand Fournier

2007-01-01

Based on the empirical analysis of data contained in the International Software Benchmarking Standards Group(ISBSG) repository, this paper presents software engineering project duration models based on project effort. Duration models are built for the entire dataset and for subsets of projects developed for personal computer, mid-range and mainframeplatforms. Duration models are also constructed for projects requiring fewer than 400 person-hours of effort and for projectsre quiring more than 400 person-hours of effort. The usefulness of adding the maximum number of assigned resources as asecond independent variable to explain duration is also analyzed. The opportunity to build duration models directly fromproject functional size in function points is investigated as well.

Software Tools for Electrical Quality Assurance in the LHC

CERN Document Server

Bednarek, Mateusz

2011-01-01

There are over 1600 superconducting magnet circuits in the LHC machine. Many of them consist of a large number of components electrically connected in series. This enhances the sensitivity of the whole circuits to electrical faults of individual components. Furthermore, circuits are equipped with a large number of instrumentation wires, which are exposed to accidental damage or swapping. In order to ensure safe operation, an Electrical Quality Assurance (ELQA) campaign is needed after each thermal cycle. Due to the complexity of the circuits, as well as their distant geographical distribution (tunnel of 27km circumference divided in 8 sectors), suitable software and hardware platforms had to be developed. The software combines an Oracle database, LabView data acquisition applications and PHP-based web follow-up tools. This paper describes the software used for the ELQA of the LHC.

Software tools for electrical quality assurance in the LHC

International Nuclear Information System (INIS)

Bednarek, M.; Ludwin, J.

2012-01-01

There are over 1600 superconducting magnet circuits in the LHC machine. Many of them consist of a large number of components electrically connected in series. This enhances the sensitivity of the whole circuits to electrical faults of individual components. Furthermore, circuits are equipped with a large number of instrumentation wires, which are exposed to accidental damage or swapping. In order to ensure safe operation, an Electrical Quality Assurance (ELQA) campaign is needed after each thermal cycle. Due to the complexity of the circuits, as well as their distant geographical distribution (tunnel of 27 km circumference divided in 8 sectors), suitable software and hardware platforms had to be developed. The software combines an Oracle database, LabView data acquisition applications and PHP-based web follow-up tools. This paper describes the software used for the ELQA of the LHC. (authors)

Guidance and Control Software Project Data - Volume 3: Verification Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes the verification documents from the GCS project. Volume 3 contains four appendices: A. Software Verification Cases and Procedures for the Guidance and Control Software Project; B. Software Verification Results for the Pluto Implementation of the Guidance and Control Software; C. Review Records for the Pluto Implementation of the Guidance and Control Software; and D. Test Results Logs for the Pluto Implementation of the Guidance and Control Software.

An automatic speech recognition system with speaker-independent identification support

Science.gov (United States)

Caranica, Alexandru; Burileanu, Corneliu

2015-02-01

The novelty of this work relies on the application of an open source research software toolkit (CMU Sphinx) to train, build and evaluate a speech recognition system, with speaker-independent support, for voice-controlled hardware applications. Moreover, we propose to use the trained acoustic model to successfully decode offline voice commands on embedded hardware, such as an ARMv6 low-cost SoC, Raspberry PI. This type of single-board computer, mainly used for educational and research activities, can serve as a proof-of-concept software and hardware stack for low cost voice automation systems.

Nuclear and Particle Physics Simulations: The Consortium of Upper-Level Physics Software

Science.gov (United States)

Bigelow, Roberta; Moloney, Michael J.; Philpott, John; Rothberg, Joseph

1995-06-01

The Consortium for Upper Level Physics Software (CUPS) has developed a comprehensive series of Nine Book/Software packages that Wiley will publish in FY `95 and `96. CUPS is an international group of 27 physicists, all with extensive backgrounds in the research, teaching, and development of instructional software. The project is being supported by the National Science Foundation (PHY-9014548), and it has received other support from the IBM Corp., Apple Computer Corp., and George Mason University. The Simulations being developed are: Astrophysics, Classical Mechanics, Electricity & Magnetism, Modern Physics, Nuclear and Particle Physics, Quantum Mechanics, Solid State, Thermal and Statistical, and Wave and Optics.

Software tool for physics chart checks.

Science.gov (United States)

Li, H Harold; Wu, Yu; Yang, Deshan; Mutic, Sasa

2014-01-01

Physics chart check has long been a central quality assurance (QC) measure in radiation oncology. The purpose of this work is to describe a software tool that aims to accomplish simplification, standardization, automation, and forced functions in the process. Nationally recognized guidelines, including American College of Radiology and American Society for Radiation Oncology guidelines and technical standards, and the American Association of Physicists in Medicine Task Group reports were identified, studied, and summarized. Meanwhile, the reported events related to physics chart check service were analyzed using an event reporting and learning system. A number of shortfalls in the chart check process were identified. To address these problems, a software tool was designed and developed under Microsoft. Net in C# to hardwire as many components as possible at each stage of the process. The software consists of the following 4 independent modules: (1) chart check management; (2) pretreatment and during treatment chart check assistant; (3) posttreatment chart check assistant; and (4) quarterly peer-review management. The users were a large group of physicists in the author's radiation oncology clinic. During over 1 year of use the tool has proven very helpful in chart checking management, communication, documentation, and maintaining consistency. The software tool presented in this work aims to assist physicists at each stage of the physics chart check process. The software tool is potentially useful for any radiation oncology clinics that are either in the process of pursuing or maintaining the American College of Radiology accreditation.

Software engineering architecture-driven software development

CERN Document Server

Schmidt, Richard F

2013-01-01

Software Engineering: Architecture-driven Software Development is the first comprehensive guide to the underlying skills embodied in the IEEE's Software Engineering Body of Knowledge (SWEBOK) standard. Standards expert Richard Schmidt explains the traditional software engineering practices recognized for developing projects for government or corporate systems. Software engineering education often lacks standardization, with many institutions focusing on implementation rather than design as it impacts product architecture. Many graduates join the workforce with incomplete skil

Quality control in dual head γ-cameras: comparison between methods and software s used for image analysis

International Nuclear Information System (INIS)

Nayl E, A.; Fornasier, M. R.; De Denaro, M.; Sulieman, A.; Alkhorayef, M.; Bradley, D.

2017-10-01

Patient radiation dose and image quality are the main issues in nuclear medicine (Nm) procedures. Currently, many protocols are used for image acquisition and analysis of quality control (Qc) tests. National Electrical Manufacturers Association (Nema) methods and protocols are widely accepted method used for providing accurate description, measurement and reporting of γ-camera performance parameters. However, no standard software is available for image analysis. The aim os this study was to compare between the vendor Qc software analysis and three software from different developers downloaded free from internet; NMQC, Nm Tool kit and ImageJ-Nm Tool kit software. The three software are used for image analysis of some Qc tests for γ-cameras based on Nema protocols including non-uniformity evaluation. Ten non-uniformity Qc images were taken from dual head γ-camera (Siemens Symbia) installed in Trieste general hospital (Italy), and analyzed. Excel analysis was used as baseline calculation of the non-uniformity test according Nema procedures. The results of the non-uniformity analysis showed good agreement between the three independent software and excel calculation (the average differences were 0.3%, 2.9%, 1.3% and 1.6% for UFOV integral, UFOV differential, CFOV integral and CFOV differential respectively), while significant difference was detected on the analysis of the company Qc software with compare to the excel analysis (the average differences were 14.6%, 20.7%, 25.7% and 31.9% for UFOV integral, UFOV differential, CFOV integral and CFOV differential respectively). NMQC software was the best in comparison with the excel calculations. The variation in the results is due to different pixel sizes used for analysis in the three software and the γ-camera Qc software. Therefore, is important to perform the tests by the vendor Qc software as well as by independent analysis to understand the differences between the values. Moreover, the medical physicist should know

Quality control in dual head γ-cameras: comparison between methods and software s used for image analysis

Energy Technology Data Exchange (ETDEWEB)

Nayl E, A. [Sudan Atomic Energy Commission, Radiation Safety Institute, Khartoum (Sudan); Fornasier, M. R.; De Denaro, M. [Azienda Sanitaria Universitaria Integrata di Trieste, Medical Physics Department, Via Giovanni Sai 7, 34128 Trieste (Italy); Sulieman, A. [Prince Sattam bin Abdulaziz University, College of Applied Medical Sciences, Radiology and Medical Imaging Department, P. O. Box 422, 11942 Al-Kharj (Saudi Arabia); Alkhorayef, M.; Bradley, D., E-mail: abdwsh10@hotmail.com [University of Surrey, Department of Physics, GU2-7XH Guildford, Surrey (United Kingdom)

2017-10-15

Patient radiation dose and image quality are the main issues in nuclear medicine (Nm) procedures. Currently, many protocols are used for image acquisition and analysis of quality control (Qc) tests. National Electrical Manufacturers Association (Nema) methods and protocols are widely accepted method used for providing accurate description, measurement and reporting of γ-camera performance parameters. However, no standard software is available for image analysis. The aim os this study was to compare between the vendor Qc software analysis and three software from different developers downloaded free from internet; NMQC, Nm Tool kit and ImageJ-Nm Tool kit software. The three software are used for image analysis of some Qc tests for γ-cameras based on Nema protocols including non-uniformity evaluation. Ten non-uniformity Qc images were taken from dual head γ-camera (Siemens Symbia) installed in Trieste general hospital (Italy), and analyzed. Excel analysis was used as baseline calculation of the non-uniformity test according Nema procedures. The results of the non-uniformity analysis showed good agreement between the three independent software and excel calculation (the average differences were 0.3%, 2.9%, 1.3% and 1.6% for UFOV integral, UFOV differential, CFOV integral and CFOV differential respectively), while significant difference was detected on the analysis of the company Qc software with compare to the excel analysis (the average differences were 14.6%, 20.7%, 25.7% and 31.9% for UFOV integral, UFOV differential, CFOV integral and CFOV differential respectively). NMQC software was the best in comparison with the excel calculations. The variation in the results is due to different pixel sizes used for analysis in the three software and the γ-camera Qc software. Therefore, is important to perform the tests by the vendor Qc software as well as by independent analysis to understand the differences between the values. Moreover, the medical physicist should know

Computer system organization the B5700/B6700 series

CERN Document Server

Organick, Elliott I

1973-01-01

Computer System Organization: The B5700/B6700 Series focuses on the organization of the B5700/B6700 Series developed by Burroughs Corp. More specifically, it examines how computer systems can (or should) be organized to support, and hence make more efficient, the running of computer programs that evolve with characteristically similar information structures.Comprised of nine chapters, this book begins with a background on the development of the B5700/B6700 operating systems, paying particular attention to their hardware/software architecture. The discussion then turns to the block-structured p

The December 2006 ATLAS Computing & Software Workshop

CERN Multimedia

Fred Luehring

The 29th ATLAS Computing & Software Workshop was held on December 11-15 at CERN. With the rapidly approaching onset of data taking, the workshop participants had an air of urgency about them. There was considerable discussion on hot topics such as physics validation of the software, data analysis, actual software production on the GRID, and the schedule of work for 2007 including the Final Dress Rehearsal (FDR). However don't be fooled, the workshop was not all work - there were also two social events which were greatly enjoyed by the attendees. The workshop welcomed Wouter Verkerke as the new Physics Validation Coordinator (replacing Davide Costanzo). Most recent validation work has centered on the 12.0.X release series that will be used for the Computing System Commissioning (CSC) exercise. The validation is now a big job because it needs to be done over a variety of conditions (magnetic field on/off, aligned/misaligned geometry) for every candidate release. Luckily there have been a large number of pe...

The NOvA software testing framework

International Nuclear Information System (INIS)

Tamsett, M; Group, C

2015-01-01

The NOvA experiment at Fermilab is a long-baseline neutrino experiment designed to study vε appearance in a vμ beam. NOvA has already produced more than one million Monte Carlo and detector generated files amounting to more than 1 PB in size. This data is divided between a number of parallel streams such as far and near detector beam spills, cosmic ray backgrounds, a number of data-driven triggers and over 20 different Monte Carlo configurations. Each of these data streams must be processed through the appropriate steps of the rapidly evolving, multi-tiered, interdependent NOvA software framework. In total there are greater than 12 individual software tiers, each of which performs a different function and can be configured differently depending on the input stream. In order to regularly test and validate that all of these software stages are working correctly NOvA has designed a powerful, modular testing framework that enables detailed validation and benchmarking to be performed in a fast, efficient and accessible way with minimal expert knowledge. The core of this system is a novel series of python modules which wrap, monitor and handle the underlying C++ software framework and then report the results to a slick front-end web-based interface. This interface utilises modern, cross-platform, visualisation libraries to render the test results in a meaningful way. They are fast and flexible, allowing for the easy addition of new tests and datasets. In total upwards of 14 individual streams are regularly tested amounting to over 70 individual software processes, producing over 25 GB of output files. The rigour enforced through this flexible testing framework enables NOvA to rapidly verify configurations, results and software and thus ensure that data is available for physics analysis in a timely and robust manner. (paper)

Korean WA-DGNSS User Segment Software Design

Directory of Open Access Journals (Sweden)

Sayed Chhattan Shah

2013-03-01

Full Text Available Korean WA-DGNSS is a large scale research project funded by Ministry of Land, Transport and Maritime Affairs Korea. It aims to augment the Global Navigation Satellite System by broadcasting additional signals from geostationary satellites and providing differential correction messages and integrity data for the GNSS satellites. The project is being carried out by a consortium of universities and research institutes. The research team at Electronics and Telecommunications Research Institute is involved in design and development of data processing softwares for wide area reference station and user segment. This paper focuses on user segment software design. Korean WA-DGNSS user segment software is designed to perform several functions such as calculation of pseudorange, ionosphere and troposphere delays, application of fast and slow correction messages, and data verification. It is based on a layered architecture that provides a model to develop flexible and reusable software and is divided into several independent, interchangeable and reusable components to reduce complexity and maintenance cost. The current version is designed to collect and process GPS and WA-DGNSS data however it is flexible to accommodate future GNSS systems such as GLONASS and Galileo.

Forecasting daily meteorological time series using ARIMA and regression models

Science.gov (United States)

Murat, Małgorzata; Malinowska, Iwona; Gos, Magdalena; Krzyszczak, Jaromir

2018-04-01

The daily air temperature and precipitation time series recorded between January 1, 1980 and December 31, 2010 in four European sites (Jokioinen, Dikopshof, Lleida and Lublin) from different climatic zones were modeled and forecasted. In our forecasting we used the methods of the Box-Jenkins and Holt- Winters seasonal auto regressive integrated moving-average, the autoregressive integrated moving-average with external regressors in the form of Fourier terms and the time series regression, including trend and seasonality components methodology with R software. It was demonstrated that obtained models are able to capture the dynamics of the time series data and to produce sensible forecasts.

SSE software test management STM capability: Using STM in the Ground Systems Development Environment (GSDE)

Science.gov (United States)

Church, Victor E.; Long, D.; Hartenstein, Ray; Perez-Davila, Alfredo

1992-01-01

This report is one of a series discussing configuration management (CM) topics for Space Station ground systems software development. It provides a description of the Software Support Environment (SSE)-developed Software Test Management (STM) capability, and discusses the possible use of this capability for management of developed software during testing performed on target platforms. This is intended to supplement the formal documentation of STM provided by the SEE Project. How STM can be used to integrate contractor CM and formal CM for software before delivery to operations is described. STM provides a level of control that is flexible enough to support integration and debugging, but sufficiently rigorous to insure the integrity of the testing process.

Computer- Aided Design in Power Engineering Application of Software Tools

CERN Document Server

Stojkovic, Zlatan

2012-01-01

This textbooks demonstrates the application of software tools in solving a series of problems from the field of designing power system structures and systems. It contains four chapters: The first chapter leads the reader through all the phases necessary in the procedures of computer aided modeling and simulation. It guides through the complex problems presenting on the basis of eleven original examples. The second chapter presents  application of software tools in power system calculations of power systems equipment design. Several design example calculations are carried out using engineering standards like MATLAB, EMTP/ATP, Excel & Access, AutoCAD and Simulink. The third chapters focuses on the graphical documentation using a collection of software tools (AutoCAD, EPLAN, SIMARIS SIVACON, SIMARIS DESIGN) which enable the complete automation of the development of graphical documentation of a power systems. In the fourth chapter, the application of software tools in the project management in power systems ...

Independent tunability of the double-mode-locked cw dye laser.

LENUS (Irish Health Repository)

Bourkoff, E

1979-06-01

We report a new configuration that enables the double-mode-locked cw dye laser to be independently tunable. In addition, the output coupling at each of the two wavelengths can be independently specified. A series of oscillographs shows some interesting features unique to double mode locking and also shows the effects of varying the two cavity lengths with respect to each other.

Multidimensional Recurrence Quantification Analysis (MdRQA) for the Analysis of Multidimensional Time-Series: A Software Implementation in MATLAB and Its Application to Group-Level Data in Joint Action.

Science.gov (United States)

Wallot, Sebastian; Roepstorff, Andreas; Mønster, Dan

2016-01-01

We introduce Multidimensional Recurrence Quantification Analysis (MdRQA) as a tool to analyze multidimensional time-series data. We show how MdRQA can be used to capture the dynamics of high-dimensional signals, and how MdRQA can be used to assess coupling between two or more variables. In particular, we describe applications of the method in research on joint and collective action, as it provides a coherent analysis framework to systematically investigate dynamics at different group levels-from individual dynamics, to dyadic dynamics, up to global group-level of arbitrary size. The Appendix in Supplementary Material contains a software implementation in MATLAB to calculate MdRQA measures.

Teacher's Guide to SERAPHIM Software V. Chemistry: The Central Science.

Science.gov (United States)

Bogner, Donna J.

Designed to assist chemistry teachers in selecting appropriate software programs, this publication is the fifth in a series of six teacher's guides from Project SERAPHIM, a program sponsored by the National Science Foundation. This guide is keyed to the chapters of the text "Chemistry: The Central Science." Program suggestions are…

Software FMEA analysis for safety-related application software

International Nuclear Information System (INIS)

Park, Gee-Yong; Kim, Dong Hoon; Lee, Dong Young

2014-01-01

Highlights: • We develop a modified FMEA analysis suited for applying to software architecture. • A template for failure modes on a specific software language is established. • A detailed-level software FMEA analysis on nuclear safety software is presented. - Abstract: A method of a software safety analysis is described in this paper for safety-related application software. The target software system is a software code installed at an Automatic Test and Interface Processor (ATIP) in a digital reactor protection system (DRPS). For the ATIP software safety analysis, at first, an overall safety or hazard analysis is performed over the software architecture and modules, and then a detailed safety analysis based on the software FMEA (Failure Modes and Effect Analysis) method is applied to the ATIP program. For an efficient analysis, the software FMEA analysis is carried out based on the so-called failure-mode template extracted from the function blocks used in the function block diagram (FBD) for the ATIP software. The software safety analysis by the software FMEA analysis, being applied to the ATIP software code, which has been integrated and passed through a very rigorous system test procedure, is proven to be able to provide very valuable results (i.e., software defects) that could not be identified during various system tests

Method of V ampersand V for safety-critical software in NPPs

International Nuclear Information System (INIS)

Kim, Jang-Yeol; Lee, Jang-Soo; Kwon, Kee-Choon

1997-01-01

Safety-critical software is software used in systems in which a failure could affect personal or equipment safety or result in large financial or social loss. Examples of systems using safety-critical software are systems such as plant protection systems in nuclear power plants (NPPs), process control systems in chemical plants, and medical instruments such as the Therac-25 medical accelerator. This paper presents verification and validation (V ampersand V) methodology for safety-critical software in NPP safety systems. In addition, it addresses issues related to NPP safety systems, such as independence parameters, software safety analysis (SSA) concepts, commercial off-the-shelf (COTS) software evaluation criteria, and interrelationships among software and system assurance organizations. It includes the concepts of existing industrial standards on software V ampersand V, Institute of Electrical and Electronics Engineers (IEEE) Standards 1012 and 1059. This safety-critical software V ampersand V methodology covers V ampersand V scope, a regulatory framework as part of its acceptance criteria, V ampersand V activities and task entrance and exit criteria, reviews and audits, testing and quality assurance records of V ampersand V material, configuration management activities related to V ampersand V, and software V ampersand V (SVV) plan (SVVP) production

Development of 'Enhance reconstruction package' software for whole-body PET

International Nuclear Information System (INIS)

Mizuta, Tetsuro; Imanishi, Tatsuru; Ishikawa, Akihiro

2011-01-01

We have developed 'Enhance Reconstruction Package' Software for our whole-body positron emission tomography (PET) Eminence series. This package improves image quality and streamlines the workflow in clinical PET and PET/CT studies. The present paper describes an outline of the applications for data collection, normalization, etc. and also reports some PET images obtained by the software. The signal to noise ratio was optimized in the phantom study, leading to the improvement in image quality. The real time display tool and the remote control tool would make a contribution to enhancement in operability in the routine workflow. (author)

Experimental Study on Series Operation of Sliding Vane Pump and Centrifugal Pump

OpenAIRE

Li, Tao; Zhang, Weiming; Jiang, Ming; Li, Zhengyang

2013-01-01

A platform for sliding vane pump and centrifugal pump tests is installed to study the series operation of them under different characteristics of pipeline. Firstly, the sliding vane pump and the centrifugal pump work independently, and the performance is recorded. Then, the two types of pumps are combined together, with the sliding vane pump acting as the feeding pump. Comparison is made between the performance of the independently working pump and the performance of series operation pump. Re...

A process improvement model for software verification and validation

Science.gov (United States)

Callahan, John; Sabolish, George

1994-01-01

We describe ongoing work at the NASA Independent Verification and Validation (IV&V) Facility to establish a process improvement model for software verification and validation (V&V) organizations. This model, similar to those used by some software development organizations, uses measurement-based techniques to identify problem areas and introduce incremental improvements. We seek to replicate this model for organizations involved in V&V on large-scale software development projects such as EOS and space station. At the IV&V Facility, a university research group and V&V contractors are working together to collect metrics across projects in order to determine the effectiveness of V&V and improve its application. Since V&V processes are intimately tied to development processes, this paper also examines the repercussions for development organizations in large-scale efforts.

Software for event oriented processing on multiprocessor systems

International Nuclear Information System (INIS)

Fischler, M.; Areti, H.; Biel, J.; Bracker, S.; Case, G.; Gaines, I.; Husby, D.; Nash, T.

1984-08-01

Computing intensive problems that require the processing of numerous essentially independent events are natural customers for large scale multi-microprocessor systems. This paper describes the software required to support users with such problems in a multiprocessor environment. It is based on experience with and development work aimed at processing very large amounts of high energy physics data

Software architecture for the ORNL large-coil test facility data system

International Nuclear Information System (INIS)

Blair, E.T.; Baylor, L.R.

1986-01-01

The VAX-based data-acquisition system for the International Fusion Superconducting Magnet Test Facility (IFSMTF) at Oak Ridge National Laboratory (ORNL) is a second-generation system that evolved from a PDP-11/60-based system used during the initial phase of facility testing. The VAX-based software represents a layered implementation that provides integrated access to all of the data sources within the system, decoupling end-user data retrieval from various front-end data sources through a combination of software architecture and instrumentation data bases. Independent VAX processes manage the various front-end data sources, each being responsible for controlling, monitoring, acquiring, and disposing data and control parameters for access from the data retrieval software. This paper describes the software architecture and the functionality incorporated into the various layers of the data system

Software architecture for the ORNL large coil test facility data system

International Nuclear Information System (INIS)

Blair, E.T.; Baylor, L.R.

1986-01-01

The VAX-based data acquisition system for the International Fusion Superconducting Magnet Test Facility (IFSMTF) at Oak Ridge National Laboratory (ORNL) is a second-generation system that evolved from a PDP-11/60-based system used during the initial phase of facility testing. The VAX-based software represents a layered implementation that provides integrated access to all of the data sources within the system, deoupling end-user data retrieval from various front-end data sources through a combination of software architecture and instrumentation data bases. Independent VAX processes manage the various front-end data sources, each being responsible for controlling, monitoring, acquiring and disposing data and control parameters for access from the data retrieval software. This paper describes the software architecture and the functionality incorporated into the various layers of the data system

Software for the ACP [Advanced Computer Program] multiprocessor system

International Nuclear Information System (INIS)

Biel, J.; Areti, H.; Atac, R.

1987-01-01

Software has been developed for use with the Fermilab Advanced Computer Program (ACP) multiprocessor system. The software was designed to make a system of a hundred independent node processors as easy to use as a single, powerful CPU. Subroutines have been developed by which a user's host program can send data to and get results from the program running in each of his ACP node processors. Utility programs make it easy to compile and link host and node programs, to debug a node program on an ACP development system, and to submit a debugged program to an ACP production system

Software Productivity of Field Experiments Using the Mobile Agents Open Architecture with Workflow Interoperability

Science.gov (United States)

Clancey, William J.; Lowry, Michael R.; Nado, Robert Allen; Sierhuis, Maarten

2011-01-01

We analyzed a series of ten systematically developed surface exploration systems that integrated a variety of hardware and software components. Design, development, and testing data suggest that incremental buildup of an exploration system for long-duration capabilities is facilitated by an open architecture with appropriate-level APIs, specifically designed to facilitate integration of new components. This improves software productivity by reducing changes required for reconfiguring an existing system.

Software

Energy Technology Data Exchange (ETDEWEB)

Macedo, R.; Budd, G.; Ross, E.; Wells, P.

2010-07-15

The software section of this journal presented new software programs that have been developed to help in the exploration and development of hydrocarbon resources. Software provider IHS Inc. has made additions to its geological and engineering analysis software tool, IHS PETRA, a product used by geoscientists and engineers to visualize, analyze and manage well production, well log, drilling, reservoir, seismic and other related information. IHS PETRA also includes a directional well module and a decline curve analysis module to improve analysis capabilities in unconventional reservoirs. Petris Technology Inc. has developed a software to help manage the large volumes of data. PetrisWinds Enterprise (PWE) helps users find and manage wellbore data, including conventional wireline and MWD core data; analysis core photos and images; waveforms and NMR; and external files documentation. Ottawa-based Ambercore Software Inc. has been collaborating with Nexen on the Petroleum iQ software for steam assisted gravity drainage (SAGD) producers. Petroleum iQ integrates geology and geophysics data with engineering data in 3D and 4D. Calgary-based Envirosoft Corporation has developed a software that reduces the costly and time-consuming effort required to comply with Directive 39 of the Alberta Energy Resources Conservation Board. The product includes an emissions modelling software. Houston-based Seismic Micro-Technology (SMT) has developed the Kingdom software that features the latest in seismic interpretation. Holland-based Joa Oil and Gas and Calgary-based Computer Modelling Group have both supplied the petroleum industry with advanced reservoir simulation software that enables reservoir interpretation. The 2010 software survey included a guide to new software applications designed to facilitate petroleum exploration, drilling and production activities. Oil and gas producers can use the products for a range of functions, including reservoir characterization and accounting. In

Computer-aided design in power engineering. Application of software tools

International Nuclear Information System (INIS)

Stojkovic, Zlatan

2012-01-01

Demonstrates the use software tools in the practice of design in the field of power systems. Presents many applications in the design in the field of power systems. Useful for educative purposes and practical work. This textbooks demonstrates the application of software tools in solving a series of problems from the field of designing power system structures and systems. It contains four chapters: The first chapter leads the reader through all the phases necessary in the procedures of computer aided modeling and simulation. It guides through the complex problems presenting on the basis of eleven original examples. The second chapter presents application of software tools in power system calculations of power systems equipment design. Several design example calculations are carried out using engineering standards like MATLAB, EMTP/ATP, Excel and Access, AutoCAD and Simulink. The third chapters focuses on the graphical documentation using a collection of software tools (AutoCAD, EPLAN, SIMARIS SIVACON, SIMARIS DESIGN) which enable the complete automation of the development of graphical documentation of a power systems. In the fourth chapter, the application of software tools in the project management in power systems is discussed. Here, the emphasis is put on the standard software MS Excel and MS Project.

Computer-aided design in power engineering. Application of software tools

Energy Technology Data Exchange (ETDEWEB)

Stojkovic, Zlatan

2012-07-01

Demonstrates the use software tools in the practice of design in the field of power systems. Presents many applications in the design in the field of power systems. Useful for educative purposes and practical work. This textbooks demonstrates the application of software tools in solving a series of problems from the field of designing power system structures and systems. It contains four chapters: The first chapter leads the reader through all the phases necessary in the procedures of computer aided modeling and simulation. It guides through the complex problems presenting on the basis of eleven original examples. The second chapter presents application of software tools in power system calculations of power systems equipment design. Several design example calculations are carried out using engineering standards like MATLAB, EMTP/ATP, Excel and Access, AutoCAD and Simulink. The third chapters focuses on the graphical documentation using a collection of software tools (AutoCAD, EPLAN, SIMARIS SIVACON, SIMARIS DESIGN) which enable the complete automation of the development of graphical documentation of a power systems. In the fourth chapter, the application of software tools in the project management in power systems is discussed. Here, the emphasis is put on the standard software MS Excel and MS Project.

BioContainers: an open-source and community-driven framework for software standardization

Science.gov (United States)

da Veiga Leprevost, Felipe; Grüning, Björn A.; Alves Aflitos, Saulo; Röst, Hannes L.; Uszkoreit, Julian; Barsnes, Harald; Vaudel, Marc; Moreno, Pablo; Gatto, Laurent; Weber, Jonas; Bai, Mingze; Jimenez, Rafael C.; Sachsenberg, Timo; Pfeuffer, Julianus; Vera Alvarez, Roberto; Griss, Johannes; Nesvizhskii, Alexey I.; Perez-Riverol, Yasset

2017-01-01

Abstract Motivation BioContainers (biocontainers.pro) is an open-source and community-driven framework which provides platform independent executable environments for bioinformatics software. BioContainers allows labs of all sizes to easily install bioinformatics software, maintain multiple versions of the same software and combine tools into powerful analysis pipelines. BioContainers is based on popular open-source projects Docker and rkt frameworks, that allow software to be installed and executed under an isolated and controlled environment. Also, it provides infrastructure and basic guidelines to create, manage and distribute bioinformatics containers with a special focus on omics technologies. These containers can be integrated into more comprehensive bioinformatics pipelines and different architectures (local desktop, cloud environments or HPC clusters). Availability and Implementation The software is freely available at github.com/BioContainers/. Contact yperez@ebi.ac.uk PMID:28379341

BioContainers: an open-source and community-driven framework for software standardization.

Science.gov (United States)

da Veiga Leprevost, Felipe; Grüning, Björn A; Alves Aflitos, Saulo; Röst, Hannes L; Uszkoreit, Julian; Barsnes, Harald; Vaudel, Marc; Moreno, Pablo; Gatto, Laurent; Weber, Jonas; Bai, Mingze; Jimenez, Rafael C; Sachsenberg, Timo; Pfeuffer, Julianus; Vera Alvarez, Roberto; Griss, Johannes; Nesvizhskii, Alexey I; Perez-Riverol, Yasset

2017-08-15

BioContainers (biocontainers.pro) is an open-source and community-driven framework which provides platform independent executable environments for bioinformatics software. BioContainers allows labs of all sizes to easily install bioinformatics software, maintain multiple versions of the same software and combine tools into powerful analysis pipelines. BioContainers is based on popular open-source projects Docker and rkt frameworks, that allow software to be installed and executed under an isolated and controlled environment. Also, it provides infrastructure and basic guidelines to create, manage and distribute bioinformatics containers with a special focus on omics technologies. These containers can be integrated into more comprehensive bioinformatics pipelines and different architectures (local desktop, cloud environments or HPC clusters). The software is freely available at github.com/BioContainers/. yperez@ebi.ac.uk. © The Author(s) 2017. Published by Oxford University Press.

Techniques and software tools for estimating ultrasonic signal-to-noise ratios

Science.gov (United States)

Chiou, Chien-Ping; Margetan, Frank J.; McKillip, Matthew; Engle, Brady J.; Roberts, Ronald A.

2016-02-01

At Iowa State University's Center for Nondestructive Evaluation (ISU CNDE), the use of models to simulate ultrasonic inspections has played a key role in R&D efforts for over 30 years. To this end a series of wave propagation models, flaw response models, and microstructural backscatter models have been developed to address inspection problems of interest. One use of the combined models is the estimation of signal-to-noise ratios (S/N) in circumstances where backscatter from the microstructure (grain noise) acts to mask sonic echoes from internal defects. Such S/N models have been used in the past to address questions of inspection optimization and reliability. Under the sponsorship of the National Science Foundation's Industry/University Cooperative Research Center at ISU, an effort was recently initiated to improve existing research-grade software by adding graphical user interface (GUI) to become user friendly tools for the rapid estimation of S/N for ultrasonic inspections of metals. The software combines: (1) a Python-based GUI for specifying an inspection scenario and displaying results; and (2) a Fortran-based engine for computing defect signal and backscattered grain noise characteristics. The latter makes use of several models including: the Multi-Gaussian Beam Model for computing sonic fields radiated by commercial transducers; the Thompson-Gray Model for the response from an internal defect; the Independent Scatterer Model for backscattered grain noise; and the Stanke-Kino Unified Model for attenuation. The initial emphasis was on reformulating the research-grade code into a suitable modular form, adding the graphical user interface and performing computations rapidly and robustly. Thus the initial inspection problem being addressed is relatively simple. A normal-incidence pulse/echo immersion inspection is simulated for a curved metal component having a non-uniform microstructure, specifically an equiaxed, untextured microstructure in which the average

InSAR Deformation Time Series Processed On-Demand in the Cloud

Science.gov (United States)

Horn, W. B.; Weeden, R.; Dimarchi, H.; Arko, S. A.; Hogenson, K.

2017-12-01

During this past year, ASF has developed a cloud-based on-demand processing system known as HyP3 (http://hyp3.asf.alaska.edu/), the Hybrid Pluggable Processing Pipeline, for Synthetic Aperture Radar (SAR) data. The system makes it easy for a user who doesn't have the time or inclination to install and use complex SAR processing software to leverage SAR data in their research or operations. One such processing algorithm is generation of a deformation time series product, which is a series of images representing ground displacements over time, which can be computed using a time series of interferometric SAR (InSAR) products. The set of software tools necessary to generate this useful product are difficult to install, configure, and use. Moreover, for a long time series with many images, the processing of just the interferograms can take days. Principally built by three undergraduate students at the ASF DAAC, the deformation time series processing relies the new Amazon Batch service, which enables processing of jobs with complex interconnected dependencies in a straightforward and efficient manner. In the case of generating a deformation time series product from a stack of single-look complex SAR images, the system uses Batch to serialize the up-front processing, interferogram generation, optional tropospheric correction, and deformation time series generation. The most time consuming portion is the interferogram generation, because even for a fairly small stack of images many interferograms need to be processed. By using AWS Batch, the interferograms are all generated in parallel; the entire process completes in hours rather than days. Additionally, the individual interferograms are saved in Amazon's cloud storage, so that when new data is acquired in the stack, an updated time series product can be generated with minimal addiitonal processing. This presentation will focus on the development techniques and enabling technologies that were used in developing the time

Variability of global left ventricular deformation analysis using vendor dependent and independent two-dimensional speckle-tracking software in adults

DEFF Research Database (Denmark)

Risum, Niels; Ali, Sophia; Olsen, Niels T

2012-01-01

Evaluation of myocardial deformation by two-dimensional speckle-tracking is useful for clinical and research purposes. However, differences may exist among different ultrasound machines, software packages, frame rates, and observers.......Evaluation of myocardial deformation by two-dimensional speckle-tracking is useful for clinical and research purposes. However, differences may exist among different ultrasound machines, software packages, frame rates, and observers....

A software product line approach to enhance a meta-scheduler middleware

International Nuclear Information System (INIS)

Scheidt, Rafael F; Schmidt, Katreen; Pessoa, Gabriel M; Viera, Matheus A; Dantas, Mario

2012-01-01

Software Projects in general tend to get more software reuse and componentization in order to reduce time, cost and new products resources. The need for techniques and tools to organize projects of higher quality in less time is one of the greatest challenges of Software Engineering. The Software Product Line is proposed to organize and systematically assist the development of new products in series at the same domain. In this context, this paper is proposed to apply the Software Product Line approach in Distributed Computing Environments. In projects that involve Distributed Environments, each version of the same product can generate repeatedly the same artifacts in a product that evolves its characteristics; however there is a principal architecture with variations of components. The goal of the proposed approach is to analyze the actual process and propose a new approach to develop new projects reusing the whole architecture, components and documents, starting with a solid base and creating new products focusing in new functionalities. We expect that with the application of this approach give support to the development of projects in Distributed Computing Environment.

Exploring the Role of Usability in the Software Process: A Study of Irish Software SMEs

Science.gov (United States)

O'Connor, Rory V.

This paper explores the software processes and usability techniques used by Small and Medium Enterprises (SMEs) that develop web applications. The significance of this research is that it looks at development processes used by SMEs in order to assess to what degree usability is integrated into the process. This study seeks to gain an understanding into the level of awareness of usability within SMEs today and their commitment to usability in practice. The motivation for this research is to explore the current development processes used by SMEs in developing web applications and to understand how usability is represented in those processes. The background for this research is provided by the growth of the web application industry beyond informational web sites to more sophisticated applications delivering a broad range of functionality. This paper presents an analysis of the practices of several Irish SMEs that develop web applications through a series of case studies. With the focus on SMEs that develop web applications as Management Information Systems and not E-Commerce sites, informational sites, online communities or web portals. This study gathered data about the usability techniques practiced by these companies and their awareness of usability in the context of the software process in those SMEs. The contribution of this study is to further the understanding of the current role of usability within the software development processes of SMEs that develop web applications.

An algorithm of Saxena-Easo on fuzzy time series forecasting

Science.gov (United States)

Ramadhani, L. C.; Anggraeni, D.; Kamsyakawuni, A.; Hadi, A. F.

2018-04-01

This paper presents a forecast model of Saxena-Easo fuzzy time series prediction to study the prediction of Indonesia inflation rate in 1970-2016. We use MATLAB software to compute this method. The algorithm of Saxena-Easo fuzzy time series doesn’t need stationarity like conventional forecasting method, capable of dealing with the value of time series which are linguistic and has the advantage of reducing the calculation, time and simplifying the calculation process. Generally it’s focus on percentage change as the universe discourse, interval partition and defuzzification. The result indicate that between the actual data and the forecast data are close enough with Root Mean Square Error (RMSE) = 1.5289.

Examining software complexity and quality for scientific software

International Nuclear Information System (INIS)

Kelly, D.; Shepard, T.

2005-01-01

Research has not found a simple relationship between software complexity and software quality, and particularly no relationship between commonly used software complexity metrics and the occurrence of software faults. A study with an example of scientific software from the nuclear power industry illustrates the importance of addressing cognitive complexity, the complexity related to understanding the intellectual content of the software. Simple practices such as aptly-named variables contributes more to high quality software than limiting code sizes. This paper examines the research into complexity and quality and reports on a longitudinal study using the example of nuclear software. (author)

A multicenter study benchmarks software tools for label-free proteome quantification.

Science.gov (United States)

Navarro, Pedro; Kuharev, Jörg; Gillet, Ludovic C; Bernhardt, Oliver M; MacLean, Brendan; Röst, Hannes L; Tate, Stephen A; Tsou, Chih-Chiang; Reiter, Lukas; Distler, Ute; Rosenberger, George; Perez-Riverol, Yasset; Nesvizhskii, Alexey I; Aebersold, Ruedi; Tenzer, Stefan

2016-11-01

Consistent and accurate quantification of proteins by mass spectrometry (MS)-based proteomics depends on the performance of instruments, acquisition methods and data analysis software. In collaboration with the software developers, we evaluated OpenSWATH, SWATH 2.0, Skyline, Spectronaut and DIA-Umpire, five of the most widely used software methods for processing data from sequential window acquisition of all theoretical fragment-ion spectra (SWATH)-MS, which uses data-independent acquisition (DIA) for label-free protein quantification. We analyzed high-complexity test data sets from hybrid proteome samples of defined quantitative composition acquired on two different MS instruments using different SWATH isolation-window setups. For consistent evaluation, we developed LFQbench, an R package, to calculate metrics of precision and accuracy in label-free quantitative MS and report the identification performance, robustness and specificity of each software tool. Our reference data sets enabled developers to improve their software tools. After optimization, all tools provided highly convergent identification and reliable quantification performance, underscoring their robustness for label-free quantitative proteomics.

Application of PIMS Software in Monthly Planning of Refinery Production

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

This article describes the application of the PIMS software in formulating monthly refining production plan. Application of the PIMS software can help to solve a series of problems related with monthly plan of refining production such as optimized selection of crude and feedstocks, optimized selection of production scale and processing scheme, identification of bottlenecks and their mitigation,optimized selection of turnaround time and optimized selection of operating regime, which have increased the economic benefits of refining enterprises. With the further development and improvement of models the PIMS software will play an increasingly important role in formulating monthly plans of refining operations and production management at refineries. This article also explores the problems existing in refinery monthly planning, and has made recommendations on developing and improving models and reporting system, enhancement of basic data acquisition, model maintenance personnel and staff training.

A computer-aided control system for automatic performance measurements on the LHC series dipoles

International Nuclear Information System (INIS)

Gorskaya, E.; Samojlov, V.; Raimondo, A.; Rijllart, A.

2003-01-01

The control system software (Test Master) for the Large Hadron Collider (LHC) magnet series measurements is presented. This system was developed at CERN to automate as many tests on the LHC magnets as possible. The Test Master software is the middle layer of the main software architecture developed by the LHC/IAS group for central supervision of all types of LHC dipole tests in the SM18 hall. It serves as a manager and scheduler for applications, controlling all measurements that are performed in a cluster of two test benches. The software was implemented in the LabVIEW environment. The information about the interactive user interface, the software architecture, communication protocols, file-configuration different types of commands and status files of the Test Master are described

Product-oriented Software Certification Process for Software Synthesis

Science.gov (United States)

Nelson, Stacy; Fischer, Bernd; Denney, Ewen; Schumann, Johann; Richardson, Julian; Oh, Phil

2004-01-01

The purpose of this document is to propose a product-oriented software certification process to facilitate use of software synthesis and formal methods. Why is such a process needed? Currently, software is tested until deemed bug-free rather than proving that certain software properties exist. This approach has worked well in most cases, but unfortunately, deaths still occur due to software failure. Using formal methods (techniques from logic and discrete mathematics like set theory, automata theory and formal logic as opposed to continuous mathematics like calculus) and software synthesis, it is possible to reduce this risk by proving certain software properties. Additionally, software synthesis makes it possible to automate some phases of the traditional software development life cycle resulting in a more streamlined and accurate development process.

Fuzzy/Neural Software Estimates Costs of Rocket-Engine Tests

Science.gov (United States)

Douglas, Freddie; Bourgeois, Edit Kaminsky

2005-01-01

The Highly Accurate Cost Estimating Model (HACEM) is a software system for estimating the costs of testing rocket engines and components at Stennis Space Center. HACEM is built on a foundation of adaptive-network-based fuzzy inference systems (ANFIS) a hybrid software concept that combines the adaptive capabilities of neural networks with the ease of development and additional benefits of fuzzy-logic-based systems. In ANFIS, fuzzy inference systems are trained by use of neural networks. HACEM includes selectable subsystems that utilize various numbers and types of inputs, various numbers of fuzzy membership functions, and various input-preprocessing techniques. The inputs to HACEM are parameters of specific tests or series of tests. These parameters include test type (component or engine test), number and duration of tests, and thrust level(s) (in the case of engine tests). The ANFIS in HACEM are trained by use of sets of these parameters, along with costs of past tests. Thereafter, the user feeds HACEM a simple input text file that contains the parameters of a planned test or series of tests, the user selects the desired HACEM subsystem, and the subsystem processes the parameters into an estimate of cost(s).

The ATLAS software installation system for LCG/EGEE

Energy Technology Data Exchange (ETDEWEB)

Salvo, A D [Istituto Nazionale di Fisica Nucleare, sez. Roma 1 (Italy); Barchiesi, A [Universita di Roma I ' La Sapienza' (Italy); Gnanvo, K [Queen Mary and Westfield College (United Kingdom); Gwilliam, C [University of Liverpool (United Kingdom); Kennedy, J; Krobath, G [Ludwig-Maximilians-Universitaet Muenchen (Germany); Olszewski, A [Henryk Niewodniczanski Institute of Nuclear Physics, Polish Academy of Sciences (Poland); Rybkine, G [Royal Holloway College (United Kingdom)

2008-07-15

The huge amount of resources available in the Grids, and the necessity to have the most up-to-date experimental software deployed in all the sites within a few hours, have driven the need for an automatic installation system for the LHC experiments. In this work we describe the ATLAS system for the experiment software installation in LCG/EGEE, based on the Light Job Submission Framework for Installation (LJSFi), an independent job submission framework for generic submission and job tracking in EGEE. LJSFi is able to automatically discover, check, install, test and tag the full set of resources made available in LCG/EGEE to the ATLAS Virtual Organization in a few hours, depending on the site availability.

DYNAMIC PROGRAMMING APPROACH TO TESTING RESOURCE ALLOCATION PROBLEM FOR MODULAR SOFTWARE

Directory of Open Access Journals (Sweden)

P.K. Kapur

2003-02-01

Full Text Available Testing phase of a software begins with module testing. During this period modules are tested independently to remove maximum possible number of faults within a specified time limit or testing resource budget. This gives rise to some interesting optimization problems, which are discussed in this paper. Two Optimization models are proposed for optimal allocation of testing resources among the modules of a Software. In the first model, we maximize the total fault removal, subject to budgetary Constraint. In the second model, additional constraint representing aspiration level for fault removals for each module of the software is added. These models are solved using dynamic programming technique. The methods have been illustrated through numerical examples.

Software architecture for the ORNL large coil test facility data system

International Nuclear Information System (INIS)

Blair, E.T.; Baylor, L.R.

1986-01-01

The VAX based data acquisition system for the international fusion superconducting magnetic test facility (IFSMTF) at Oak Ridge National Laboratory (ORNL) is a second generation system that evolved from a PDP-11/60 based system used during the initial phase of facility testing. The VAX based software represents a layered implementation that provides integrated access to all of the data sources within the system, decoupling en-user data retrieval from various front-end data sources through a combination of software architecture and instrumentation data bases. Independent VAX processes manage the various front-end data sources, each being responsible for controlling, monitoring, acquiring, and disposing data and control parameters for access from the data retrieval software

Computer software summaries. Numbers 325 through 423

Energy Technology Data Exchange (ETDEWEB)

1978-08-01

The National Energy Software Center (NESC) serves as the software exchange and information center for the U.S. Department of Energy and the Nuclear Regulatory Commission. These summaries describe agency-sponsored software which is at the specification stage, under development, being checked out, in use, or available at agency offices, laboratories, and contractor installations. They describe software which is not included in the NESC library due to its preliminary status or because it is believed to be of limited interest. Codes dealing with the following subjects are included: cross section and resonance integral calculations; spectrum calculations, generation of group constants, lattice and cell problems; static design studies; depletion, fuel management, cost analysis, and power plant economics; space-independent kinetics; space--time kinetics, coupled neutronics--hydrodynamics--thermodynamics; and excursion simulations; radiological safety, hazard and accident analysis; heat transfer and fluid flow; deformation and stress distribution computations, structural analysis, and engineering design studies; gamma heating and shield design; reactor systems analysis; data preparation; data management; subsidiary calculations; experimental data processing; general mathematical and computing system routines; materials; environmental and earth sciences; space sciences; electronics and engineering equipment; chemistry; particle accelerators and high-voltage machines; physics; magnetic fusion research; biology and medicine; and data. (RWR)

Computer software summaries. Numbers 325 through 423

International Nuclear Information System (INIS)

1978-08-01

The National Energy Software Center (NESC) serves as the software exchange and information center for the U.S. Department of Energy and the Nuclear Regulatory Commission. These summaries describe agency-sponsored software which is at the specification stage, under development, being checked out, in use, or available at agency offices, laboratories, and contractor installations. They describe software which is not included in the NESC library due to its preliminary status or because it is believed to be of limited interest. Codes dealing with the following subjects are included: cross section and resonance integral calculations; spectrum calculations, generation of group constants, lattice and cell problems; static design studies; depletion, fuel management, cost analysis, and power plant economics; space-independent kinetics; space--time kinetics, coupled neutronics--hydrodynamics--thermodynamics; and excursion simulations; radiological safety, hazard and accident analysis; heat transfer and fluid flow; deformation and stress distribution computations, structural analysis, and engineering design studies; gamma heating and shield design; reactor systems analysis; data preparation; data management; subsidiary calculations; experimental data processing; general mathematical and computing system routines; materials; environmental and earth sciences; space sciences; electronics and engineering equipment; chemistry; particle accelerators and high-voltage machines; physics; magnetic fusion research; biology and medicine; and data

A concept of software testing for SMART MMIS software

International Nuclear Information System (INIS)

Seo, Yong Seok; Seong, Seung Hwan; Park, Keun Ok; Hur, Sub; Kim, Dong Hoon

2001-01-01

In order to achieve high quality of SMART MMIS software, the well-constructed software testing concept shall be required. This paper established software testing concept which is to be applied to SMART MMIS software, in terms of software testing organization, documentation. procedure, and methods. The software testing methods are classified into source code static analysis and dynamic testing. The software dynamic testing methods are discussed with two aspects: white-box and black-box testing. As software testing concept introduced in this paper is applied to the SMART MMIS software. the high quality of the software will be produced. In the future, software failure data will be collected through the construction of SMART MMIS prototyping facility which the software testing concept of this paper is applied to

Fuzzy 5F Analysis of an Independent Chinese Auto Company

OpenAIRE

陳, 法恩; 古殿, 幸雄; チン, ホウオン; コドノ, ユキオ; Faen, Chen; Yukio, Kodono

2014-01-01

　The Chinese market is indispensable to international automobile companies, who are thus expanding investment in the country’s automotive industry. To increase their market share in China, automobile manufacturers and independent automotive enterprises have implemented a series of management strategies. Consequently, competition in China is becoming increasingly intense. At the same time, Chinese automobile companies have no international brand recognition.　 In this paper, an independent auto...

Terra Harvest software architecture

Science.gov (United States)

Humeniuk, Dave; Klawon, Kevin

2012-06-01

Under the Terra Harvest Program, the DIA has the objective of developing a universal Controller for the Unattended Ground Sensor (UGS) community. The mission is to define, implement, and thoroughly document an open architecture that universally supports UGS missions, integrating disparate systems, peripherals, etc. The Controller's inherent interoperability with numerous systems enables the integration of both legacy and future UGS System (UGSS) components, while the design's open architecture supports rapid third-party development to ensure operational readiness. The successful accomplishment of these objectives by the program's Phase 3b contractors is demonstrated via integration of the companies' respective plug-'n'-play contributions that include controllers, various peripherals, such as sensors, cameras, etc., and their associated software drivers. In order to independently validate the Terra Harvest architecture, L-3 Nova Engineering, along with its partner, the University of Dayton Research Institute, is developing the Terra Harvest Open Source Environment (THOSE), a Java Virtual Machine (JVM) running on an embedded Linux Operating System. The Use Cases on which the software is developed support the full range of UGS operational scenarios such as remote sensor triggering, image capture, and data exfiltration. The Team is additionally developing an ARM microprocessor-based evaluation platform that is both energy-efficient and operationally flexible. The paper describes the overall THOSE architecture, as well as the design decisions for some of the key software components. Development process for THOSE is discussed as well.

Optimal structure of fault-tolerant software systems

International Nuclear Information System (INIS)

Levitin, Gregory

2005-01-01

This paper considers software systems consisting of fault-tolerant components. These components are built from functionally equivalent but independently developed versions characterized by different reliability and execution time. Because of hardware resource constraints, the number of versions that can run simultaneously is limited. The expected system execution time and its reliability (defined as probability of obtaining the correct output within a specified time) strictly depend on parameters of software versions and sequence of their execution. The system structure optimization problem is formulated in which one has to choose software versions for each component and find the sequence of their execution in order to achieve the greatest system reliability subject to cost constraints. The versions are to be chosen from a list of available products. Each version is characterized by its reliability, execution time and cost. The suggested optimization procedure is based on an algorithm for determining system execution time distribution that uses the moment generating function approach and on the genetic algorithm. Both N-version programming and the recovery block scheme are considered within a universal model. Illustrated example is presented

Software for precise tracking of cell proliferation

International Nuclear Information System (INIS)

Kurokawa, Hiroshi; Noda, Hisayori; Sugiyama, Mayu; Sakaue-Sawano, Asako; Fukami, Kiyoko; Miyawaki, Atsushi

2012-01-01

Highlights: ► We developed software for analyzing cultured cells that divide as well as migrate. ► The active contour model (Snakes) was used as the core algorithm. ► The time backward analysis was also used for efficient detection of cell division. ► With user-interactive correction functions, the software enables precise tracking. ► The software was successfully applied to cells with fluorescently-labeled nuclei. -- Abstract: We have developed a multi-target cell tracking program TADOR, which we applied to a series of fluorescence images. TADOR is based on an active contour model that is modified in order to be free of the problem of locally optimal solutions, and thus is resistant to signal fluctuation and morphological changes. Due to adoption of backward tracing and addition of user-interactive correction functions, TADOR is used in an off-line and semi-automated mode, but enables precise tracking of cell division. By applying TADOR to the analysis of cultured cells whose nuclei had been fluorescently labeled, we tracked cell division and cell-cycle progression on coverslips over an extended period of time.

The Use of Computer-Assisted Identification of ARIMA Time-Series.

Science.gov (United States)

Brown, Roger L.

This study was conducted to determine the effects of using various levels of tutorial statistical software for the tentative identification of nonseasonal ARIMA models, a statistical technique proposed by Box and Jenkins for the interpretation of time-series data. The Box-Jenkins approach is an iterative process encompassing several stages of…

Controls Over Operating System and Security Software Supporting the Defense Finance and Accounting Service

National Research Council Canada - National Science Library

McKinney, Terry

1994-01-01

This is the final in a series of three audits of management controls over the operating systems and security software used by the information processing centers that support the Defense Finance and Accounting Centers (DFAS...

Software Maintenance and Evolution: The Implication for Software ...

African Journals Online (AJOL)

Software Maintenance and Evolution: The Implication for Software Development. ... Software maintenance is the process of modifying existing operational software by correcting errors, ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Net-VISA used as a complement to standard software at the CTBTO: initial operational experience with next-generation software.

Science.gov (United States)

Le Bras, R. J.; Arora, N. S.; Kushida, N.; Kebede, F.; Feitio, P.; Tomuta, E.

2017-12-01

The International Monitoring System of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) has reached out to the broader scientific community through a series of conferences, the later one of which took place in June 2017 in Vienna, Austria. Stemming out of this outreach effort, after the inception of research and development efforts in 2009, the NET-VISA software, following a Bayesian modelling approach, has been elaborated to improve on the key step of automatic association of joint seismic, hydro-acoustic, and infrasound detections. When compared with the current operational system, it has been consistently shown on off-line tests to improve the overlap with the analyst-reviewed Reviewed Event Bulletin (REB) by ten percent for an average of 85% overlap, while the inconsistency rate is essentially the same at about 50%. Testing by analysts in realistic conditions on a few days of data has also demonstrated the software performance in finding additional events which qualify for publication in the REB. Starting in August 2017, the automatic events produced by the software will be reviewed by analysts at the CTBTO, and we report on the initial evaluation of this introduction into operations.

Evaluation of three state-of-the-art metabolite prediction software packages (Meteor, MetaSite, and StarDrop) through independent and synergistic use.

Science.gov (United States)

T'jollyn, H; Boussery, K; Mortishire-Smith, R J; Coe, K; De Boeck, B; Van Bocxlaer, J F; Mannens, G

2011-11-01

The aim of this study was to evaluate three different metabolite prediction software packages (Meteor, MetaSite, and StarDrop) with respect to their ability to predict loci of metabolism and suggest relative proportions of metabolites. A chemically diverse test set of 22 compounds, for which in vivo human mass balance studies and metabolic schemes were available, was used as basis for the evaluation. Each software package was provided with structures of the parent compounds, and predicted metabolites were compared with experimentally determined human metabolites. The evaluation consisted of two parts. First, different settings within each software package were investigated and the software was evaluated using those settings determined to give the best prediction. Second, the three different packages were combined using the optimized settings to see whether a synergistic effect concerning the overall metabolism prediction could be established. The performance of the software was scored for both sensitivity and precision, taking into account the capabilities/limitations of the particular software. Varying results were obtained for the individual packages. Meteor showed a general tendency toward overprediction, and this led to a relatively low precision (∼35%) but high sensitivity (∼70%). MetaSite and StarDrop both exhibited a sensitivity and precision of ∼50%. By combining predictions obtained with the different packages, we found that increased precision can be obtained. We conclude that the state-of-the-art individual metabolite prediction software has many advantageous features but needs refinement to obtain acceptable prediction profiles. Synergistic use of different software packages could prove useful.

A Technology-Neutral Role-Based Collaboration Model for Software Ecosystems

DEFF Research Database (Denmark)

Stanciulescu, Stefan; Rabiser, Daniela; Seidl, Christoph

2016-01-01

by contributing a role-based collaboration model for software ecosystems to make such implicit similarities explicit and to raise awareness among developers during their ongoing efforts. We extract this model based on realization artifacts in a specific programming language located in a particular source code......In large-scale software ecosystems, many developers contribute extensions to a common software platform. Due to the independent development efforts and the lack of a central steering mechanism, similar functionality may be developed multiple times by different developers. We tackle this problem...... efforts and information of ongoing development efforts. Finally, using the collaborations defined in the formalism we model real artifacts from Marlin, a firmware for 3D printers, and we show that for the selected scenarios, the five collaborations were sufficient to raise awareness and make implicit...

Software Replica of Minimal Living Processes

Science.gov (United States)

Bersini, Hugues

2010-04-01

There is a long tradition of software simulations in theoretical biology to complement pure analytical mathematics which are often limited to reproduce and understand the self-organization phenomena resulting from the non-linear and spatially grounded interactions of the huge number of diverse biological objects. Since John Von Neumann and Alan Turing pioneering works on self-replication and morphogenesis, proponents of artificial life have chosen to resolutely neglecting a lot of materialistic and quantitative information deemed not indispensable and have focused on the rule-based mechanisms making life possible, supposedly neutral with respect to their underlying material embodiment. Minimal life begins at the intersection of a series of processes which need to be isolated, differentiated and duplicated as such in computers. Only software developments and running make possible to understand the way these processes are intimately interconnected in order for life to appear at the crossroad. In this paper, I will attempt to set out the history of life as the disciples of artificial life understand it, by placing these different lessons on a temporal and causal axis, showing which one is indispensable to the appearance of the next and how does it connect to the next. I will discuss the task of artificial life as setting up experimental software platforms where these different lessons, whether taken in isolation or together, are tested, simulated, and, more systematically, analyzed. I will sketch some of these existing software platforms: chemical reaction networks, Varela’s autopoietic cellular automata, Ganti’s chemoton model, whose running delivers interesting take home messages to open-minded biologists.

Insurer Provide Rating Software and Competitive Advantage: An Evaluation Based on BOP Insurance Applications at Wisconsin Agencies

OpenAIRE

Thomas A. Aiuppa; William E. Wehrs

1993-01-01

This research examines whether a competitive advantage exists for insurers which provide independent agencies with rating software to generate price quotes. Data relative to the Business Owners line of insurance were collected from several Wisconsin agencies which represent several BOP insurers, some of which provide software for rating BOP applications. The results indicate that providing rating software did not increase insurers’ business volumes, but may decrease their underwriting costs. ...

A tool to include gamma analysis software into a quality assurance program.

Science.gov (United States)

Agnew, Christina E; McGarry, Conor K

2016-03-01

To provide a tool to enable gamma analysis software algorithms to be included in a quality assurance (QA) program. Four image sets were created comprising two geometric images to independently test the distance to agreement (DTA) and dose difference (DD) elements of the gamma algorithm, a clinical step and shoot IMRT field and a clinical VMAT arc. The images were analysed using global and local gamma analysis with 2 in-house and 8 commercially available software encompassing 15 software versions. The effect of image resolution on gamma pass rates was also investigated. All but one software accurately calculated the gamma passing rate for the geometric images. Variation in global gamma passing rates of 1% at 3%/3mm and over 2% at 1%/1mm was measured between software and software versions with analysis of appropriately sampled images. This study provides a suite of test images and the gamma pass rates achieved for a selection of commercially available software. This image suite will enable validation of gamma analysis software within a QA program and provide a frame of reference by which to compare results reported in the literature from various manufacturers and software versions. Copyright © 2015. Published by Elsevier Ireland Ltd.

Software Development in the Water Sciences: a view from the divide (Invited)

Science.gov (United States)

Miles, B.; Band, L. E.

2013-12-01

While training in statistical methods is an important part of many earth scientists' training, these scientists often learn the bulk of their software development skills in an ad hoc, just-in-time manner. Yet to carry out contemporary research scientists are spending more and more time developing software. Here I present perspectives - as an earth sciences graduate student with professional software engineering experience - on the challenges scientists face adopting software engineering practices, with an emphasis on areas of the science software development lifecycle that could benefit most from improved engineering. This work builds on experience gained as part of the NSF-funded Water Science Software Institute (WSSI) conceptualization award (NSF Award # 1216817). Throughout 2013, the WSSI team held a series of software scoping and development sprints with the goals of: (1) adding features to better model green infrastructure within the Regional Hydro-Ecological Simulation System (RHESSys); and (2) infusing test-driven agile software development practices into the processes employed by the RHESSys team. The goal of efforts such as the WSSI is to ensure that investments by current and future scientists in software engineering training will enable transformative science by improving both scientific reproducibility and researcher productivity. Experience with the WSSI indicates: (1) the potential for achieving this goal; and (2) while scientists are willing to adopt some software engineering practices, transformative science will require continued collaboration between domain scientists and cyberinfrastructure experts for the foreseeable future.

SOFTWARE EFFORT ESTIMATION FRAMEWORK TO IMPROVE ORGANIZATION PRODUCTIVITY USING EMOTION RECOGNITION OF SOFTWARE ENGINEERS IN SPONTANEOUS SPEECH

Directory of Open Access Journals (Sweden)

B.V.A.N.S.S. Prabhakar Rao

2015-10-01

Full Text Available Productivity is a very important part of any organisation in general and software industry in particular. Now a day’s Software Effort estimation is a challenging task. Both Effort and Productivity are inter-related to each other. This can be achieved from the employee’s of the organization. Every organisation requires emotionally stable employees in their firm for seamless and progressive working. Of course, in other industries this may be achieved without man power. But, software project development is labour intensive activity. Each line of code should be delivered from software engineer. Tools and techniques may helpful and act as aid or supplementary. Whatever be the reason software industry has been suffering with success rate. Software industry is facing lot of problems in delivering the project on time and within the estimated budget limit. If we want to estimate the required effort of the project it is significant to know the emotional state of the team member. The responsibility of ensuring emotional contentment falls on the human resource department and the department can deploy a series of systems to carry out its survey. This analysis can be done using a variety of tools, one such, is through study of emotion recognition. The data needed for this is readily available and collectable and can be an excellent source for the feedback systems. The challenge of recognition of emotion in speech is convoluted primarily due to the noisy recording condition, the variations in sentiment in sample space and exhibition of multiple emotions in a single sentence. The ambiguity in the labels of training set also increases the complexity of problem addressed. The existing models using probabilistic models have dominated the study but present a flaw in scalability due to statistical inefficiency. The problem of sentiment prediction in spontaneous speech can thus be addressed using a hybrid system comprising of a Convolution Neural Network and

Evaluation of The Virtual Cells Software: a Teaching Tool

Directory of Open Access Journals (Sweden)

C.C.P. da Silva

2005-07-01

Full Text Available Studies show that the use of games and interactive materials  at schools is a good educational strategy, motivating students to create mental  outlines and developing the reasoning and facilitating  the learn- ing. In this context, the Scientific Dissemination Coordination of the Center  for Structural Molecular Biotechnology  (CBME,  developed  a series of educational materials  destined  to the  elementary and high  schools,  universities  and  general  public.   Among  these,  we highlighted  the  Virtual  Cells soft- ware that was developed  with  the  aim of helping  in the  understanding of the  basic concepts  of cell types,  their  structures, organelles  and  specific functions.   Characterized by its  interactive  interface, this  software shows eukaryotes  and prokaryotes cells images, where organelles are shown as dynamic structures. In addition, it presents exercises in another  step that reinforce the comprehension  of Cy- tology.  A speaker  narrates the  resources  offered by the  program  and  the  necessary  steps  for its use. During  the  stage  of development of the  software,  students and  teachers of public and  private  high schools from Sao Carlos  city, Sao Paulo  State,  were invited  to register their  opinions  regarding  the language and content of the software in order to help us in the improvement of it.  After this stage, the Scientific Dissemination Coordination of CBME organized a series of workshops, where 120 individuals evaluated the software (students and teachers  of high school and others undergraduate students. For this evaluation, a questionnaire was elaborated based on the international current literature in the area of sciences teaching  and it was applied  after the interactive section with the software.  The analysis of the results demonstrated that most of the individuals  considered the software of easy

Software Engineering Program: Software Process Improvement Guidebook

Science.gov (United States)

1996-01-01

The purpose of this document is to provide experience-based guidance in implementing a software process improvement program in any NASA software development or maintenance community. This guidebook details how to define, operate, and implement a working software process improvement program. It describes the concept of the software process improvement program and its basic organizational components. It then describes the structure, organization, and operation of the software process improvement program, illustrating all these concepts with specific NASA examples. The information presented in the document is derived from the experiences of several NASA software organizations, including the SEL, the SEAL, and the SORCE. Their experiences reflect many of the elements of software process improvement within NASA. This guidebook presents lessons learned in a form usable by anyone considering establishing a software process improvement program within his or her own environment. This guidebook attempts to balance general and detailed information. It provides material general enough to be usable by NASA organizations whose characteristics do not directly match those of the sources of the information and models presented herein. It also keeps the ideas sufficiently close to the sources of the practical experiences that have generated the models and information.

Software quality assurance plans for safety-critical software

International Nuclear Information System (INIS)

Liddle, P.

2006-01-01

Application software is defined as safety-critical if a fault in the software could prevent the system components from performing their nuclear-safety functions. Therefore, for nuclear-safety systems, the AREVA TELEPERM R XS (TXS) system is classified 1E, as defined in the Inst. of Electrical and Electronics Engineers (IEEE) Std 603-1998. The application software is classified as Software Integrity Level (SIL)-4, as defined in IEEE Std 7-4.3.2-2003. The AREVA NP Inc. Software Program Manual (SPM) describes the measures taken to ensure that the TELEPERM XS application software attains a level of quality commensurate with its importance to safety. The manual also describes how TELEPERM XS correctly performs the required safety functions and conforms to established technical and documentation requirements, conventions, rules, and standards. The program manual covers the requirements definition, detailed design, integration, and test phases for the TELEPERM XS application software, and supporting software created by AREVA NP Inc. The SPM is required for all safety-related TELEPERM XS system applications. The program comprises several basic plans and practices: 1. A Software Quality-Assurance Plan (SQAP) that describes the processes necessary to ensure that the software attains a level of quality commensurate with its importance to safety function. 2. A Software Safety Plan (SSP) that identifies the process to reasonably ensure that safety-critical software performs as intended during all abnormal conditions and events, and does not introduce any new hazards that could jeopardize the health and safety of the public. 3. A Software Verification and Validation (V and V) Plan that describes the method of ensuring the software is in accordance with the requirements. 4. A Software Configuration Management Plan (SCMP) that describes the method of maintaining the software in an identifiable state at all times. 5. A Software Operations and Maintenance Plan (SO and MP) that

Statistical tools for analysis and modeling of cosmic populations and astronomical time series: CUDAHM and TSE

Science.gov (United States)

Loredo, Thomas; Budavari, Tamas; Scargle, Jeffrey D.

2018-01-01

This presentation provides an overview of open-source software packages addressing two challenging classes of astrostatistics problems. (1) CUDAHM is a C++ framework for hierarchical Bayesian modeling of cosmic populations, leveraging graphics processing units (GPUs) to enable applying this computationally challenging paradigm to large datasets. CUDAHM is motivated by measurement error problems in astronomy, where density estimation and linear and nonlinear regression must be addressed for populations of thousands to millions of objects whose features are measured with possibly complex uncertainties, potentially including selection effects. An example calculation demonstrates accurate GPU-accelerated luminosity function estimation for simulated populations of $10^6$ objects in about two hours using a single NVIDIA Tesla K40c GPU. (2) Time Series Explorer (TSE) is a collection of software in Python and MATLAB for exploratory analysis and statistical modeling of astronomical time series. It comprises a library of stand-alone functions and classes, as well as an application environment for interactive exploration of times series data. The presentation will summarize key capabilities of this emerging project, including new algorithms for analysis of irregularly-sampled time series.

Intellectual Property Protection of Software – At the Crossroads of Software Patents and Open Source Software

OpenAIRE

Tantarimäki, Maria

2018-01-01

The thesis considers the intellectual property protection of software in Europe and in the US, which is increasingly important subject as the world is globalizing and digitalizing. The special nature of software has challenges the intellectual property rights. The current protection of software is based on copyright protection but in this thesis, two other options are considered: software patents and open source software. Software patents provide strong protection for software whereas the pur...

Hardware independence checkout software

Science.gov (United States)

Cameron, Barry W.; Helbig, H. R.

1990-01-01

ACSI has developed a program utilizing CLIPS to assess compliance with various programming standards. Essentially the program parses C code to extract the names of all function calls. These are asserted as CLIPS facts which also include information about line numbers, source file names, and called functions. Rules have been devised to establish functions called that have not been defined in any of the source parsed. These are compared against lists of standards (represented as facts) using rules that check intersections and/or unions of these. By piping the output into other processes the source is appropriately commented by generating and executing parsed scripts.

Software Quality Assurance in Software Projects: A Study of Pakistan

OpenAIRE

Faisal Shafique Butt; Sundus Shaukat; M. Wasif Nisar; Ehsan Ullah Munir; Muhammad Waseem; Kashif Ayyub

2013-01-01

Software quality is specific property which tells what kind of standard software should have. In a software project, quality is the key factor of success and decline of software related organization. Many researches have been done regarding software quality. Software related organization follows standards introduced by Capability Maturity Model Integration (CMMI) to achieve good quality software. Quality is divided into three main layers which are Software Quality Assurance (SQA), Software Qu...

A comment on measuring the Hurst exponent of financial time series

Science.gov (United States)

Couillard, Michel; Davison, Matt

2005-03-01

A fundamental hypothesis of quantitative finance is that stock price variations are independent and can be modeled using Brownian motion. In recent years, it was proposed to use rescaled range analysis and its characteristic value, the Hurst exponent, to test for independence in financial time series. Theoretically, independent time series should be characterized by a Hurst exponent of 1/2. However, finite Brownian motion data sets will always give a value of the Hurst exponent larger than 1/2 and without an appropriate statistical test such a value can mistakenly be interpreted as evidence of long term memory. We obtain a more precise statistical significance test for the Hurst exponent and apply it to real financial data sets. Our empirical analysis shows no long-term memory in some financial returns, suggesting that Brownian motion cannot be rejected as a model for price dynamics.

Development of neutron activation analysis software

International Nuclear Information System (INIS)

Wang Liyu

1987-10-01

The software for quantitative neutron activation analysis was developed to run under the MS/DOS operating system. The programmes of the IBM/SPAN include: spectra file transfer from and to a Canberra Series 35 multichannel analyzer, spectrum evaluation routines, calibration subprogrammes, and quantitative analysis. The programmes for spectrum analysis include fitting routine for separation of multiple lines by reproducing the peak shape with a combination of Gaussian and exponential terms. The programmes were tested on an IBM/AT-compatible computer. The programmes and the sources are available costfree for the IAEA projects of Technical Cooperation. 7 refs, 3 figs

A first application of independent component analysis to extracting structure from stock returns.

Science.gov (United States)

Back, A D; Weigend, A S

1997-08-01

This paper explores the application of a signal processing technique known as independent component analysis (ICA) or blind source separation to multivariate financial time series such as a portfolio of stocks. The key idea of ICA is to linearly map the observed multivariate time series into a new space of statistically independent components (ICs). We apply ICA to three years of daily returns of the 28 largest Japanese stocks and compare the results with those obtained using principal component analysis. The results indicate that the estimated ICs fall into two categories, (i) infrequent large shocks (responsible for the major changes in the stock prices), and (ii) frequent smaller fluctuations (contributing little to the overall level of the stocks). We show that the overall stock price can be reconstructed surprisingly well by using a small number of thresholded weighted ICs. In contrast, when using shocks derived from principal components instead of independent components, the reconstructed price is less similar to the original one. ICA is shown to be a potentially powerful method of analyzing and understanding driving mechanisms in financial time series. The application to portfolio optimization is described in Chin and Weigend (1998).

A software engineering process for safety-critical software application

International Nuclear Information System (INIS)

Kang, Byung Heon; Kim, Hang Bae; Chang, Hoon Seon; Jeon, Jong Sun

1995-01-01

Application of computer software to safety-critical systems in on the increase. To be successful, the software must be designed and constructed to meet the functional and performance requirements of the system. For safety reason, the software must be demonstrated not only to meet these requirements, but also to operate safely as a component within the system. For longer-term cost consideration, the software must be designed and structured to ease future maintenance and modifications. This paper presents a software engineering process for the production of safety-critical software for a nuclear power plant. The presentation is expository in nature of a viable high quality safety-critical software development. It is based on the ideas of a rational design process and on the experience of the adaptation of such process in the production of the safety-critical software for the shutdown system number two of Wolsung 2, 3 and 4 nuclear power generation plants. This process is significantly different from a conventional process in terms of rigorous software development phases and software design techniques, The process covers documentation, design, verification and testing using mathematically precise notations and highly reviewable tabular format to specify software requirements and software requirements and software requirements and code against software design using static analysis. The software engineering process described in this paper applies the principle of information-hiding decomposition in software design using a modular design technique so that when a change is required or an error is detected, the affected scope can be readily and confidently located. it also facilitates a sense of high degree of confidence in the 'correctness' of the software production, and provides a relatively simple and straightforward code implementation effort. 1 figs., 10 refs. (Author)

Software architecture analysis tool : software architecture metrics collection

NARCIS (Netherlands)

Muskens, J.; Chaudron, M.R.V.; Westgeest, R.

2002-01-01

The Software Engineering discipline lacks the ability to evaluate software architectures. Here we describe a tool for software architecture analysis that is based on metrics. Metrics can be used to detect possible problems and bottlenecks in software architectures. Even though metrics do not give a

The automatic programming for safety-critical software in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Kim, Jang Yeol; Eom, Heung Seop; Choi, You Rark

1998-06-01

We defined the Korean unique safety-critical software development methodology by modifying Dr. Harel`s statechart-based on formal methods in order to digitalized the reactor protection system. It is suggested software requirement specification guideline to specify design specification which is basis for requirement specification and automatic programming by the caused by shutdown parameter logic of the steam generator water level for Wolsung 2/3/4 unit SDS no.1 and simulated it by binding the Graphic User Interface (GUI). We generated the K and R C code automatically by utilizing the Statemate MAGNUM Sharpshooter/C code generator. Auto-generated K and R C code is machine independent code and has high productivity, quality and provability. The following are the summaries of major research and development. - Set up the Korean unique safety-critical software development methodology - Developed software requirement specification guidelines - Developed software design specification guidelines - Reactor trip modeling for steam generator waster level Wolsung 2/3/4 SDS no. 1 shutdown parameter logic - Graphic panel binding with GUI. (author). 20 refs., 12 tabs., 15 figs

The automatic programming for safety-critical software in nuclear power plants

International Nuclear Information System (INIS)

Kim, Jang Yeol; Eom, Heung Seop; Choi, You Rark

1998-06-01

We defined the Korean unique safety-critical software development methodology by modifying Dr. Harel's statechart-based on formal methods in order to digitalized the reactor protection system. It is suggested software requirement specification guideline to specify design specification which is basis for requirement specification and automatic programming by the caused by shutdown parameter logic of the steam generator water level for Wolsung 2/3/4 unit SDS no.1 and simulated it by binding the Graphic User Interface (GUI). We generated the K and R C code automatically by utilizing the Statemate MAGNUM Sharpshooter/C code generator. Auto-generated K and R C code is machine independent code and has high productivity, quality and provability. The following are the summaries of major research and development. - Set up the Korean unique safety-critical software development methodology - Developed software requirement specification guidelines - Developed software design specification guidelines - Reactor trip modeling for steam generator waster level Wolsung 2/3/4 SDS no. 1 shutdown parameter logic - Graphic panel binding with GUI. (author). 20 refs., 12 tabs., 15 figs

Customer Interaction in Software Development: A Comparison of Software Methodologies Deployed in Namibian Software Firms

CSIR Research Space (South Africa)

Iyawa, GE

2016-01-01

Full Text Available within the Namibian context. An implication for software project managers and software developers is that customer interaction should be properly managed to ensure that the software methodologies for improving software development processes...

A SOFTWARE RELIABILITY ESTIMATION METHOD TO NUCLEAR SAFETY SOFTWARE

Directory of Open Access Journals (Sweden)

GEE-YONG PARK

2014-02-01

Full Text Available A method for estimating software reliability for nuclear safety software is proposed in this paper. This method is based on the software reliability growth model (SRGM, where the behavior of software failure is assumed to follow a non-homogeneous Poisson process. Two types of modeling schemes based on a particular underlying method are proposed in order to more precisely estimate and predict the number of software defects based on very rare software failure data. The Bayesian statistical inference is employed to estimate the model parameters by incorporating software test cases as a covariate into the model. It was identified that these models are capable of reasonably estimating the remaining number of software defects which directly affects the reactor trip functions. The software reliability might be estimated from these modeling equations, and one approach of obtaining software reliability value is proposed in this paper.

The Role and Quality of Software Safety in the NASA Constellation Program

Science.gov (United States)

Layman, Lucas; Basili, Victor R.; Zelkowitz, Marvin V.

2010-01-01

In this study, we examine software safety risk in the early design phase of the NASA Constellation spaceflight program. Obtaining an accurate, program-wide picture of software safety risk is difficult across multiple, independently-developing systems. We leverage one source of safety information, hazard analysis, to provide NASA quality assurance managers with information regarding the ongoing state of software safety across the program. The goal of this research is two-fold: 1) to quantify the relative importance of software with respect to system safety; and 2) to quantify the level of risk presented by software in the hazard analysis. We examined 154 hazard reports created during the preliminary design phase of three major flight hardware systems within the Constellation program. To quantify the importance of software, we collected metrics based on the number of software-related causes and controls of hazardous conditions. To quantify the level of risk presented by software, we created a metric scheme to measure the specificity of these software causes. We found that from 49-70% of hazardous conditions in the three systems could be caused by software or software was involved in the prevention of the hazardous condition. We also found that 12-17% of the 2013 hazard causes involved software, and that 23-29% of all causes had a software control. Furthermore, 10-12% of all controls were software-based. There is potential for inaccuracy in these counts, however, as software causes are not consistently scoped, and the presence of software in a cause or control is not always clear. The application of our software specificity metrics also identified risks in the hazard reporting process. In particular, we found a number of traceability risks in the hazard reports may impede verification of software and system safety.

Extended local similarity analysis (eLSA) of microbial community and other time series data with replicates.

Science.gov (United States)

Xia, Li C; Steele, Joshua A; Cram, Jacob A; Cardon, Zoe G; Simmons, Sheri L; Vallino, Joseph J; Fuhrman, Jed A; Sun, Fengzhu

2011-01-01

The increasing availability of time series microbial community data from metagenomics and other molecular biological studies has enabled the analysis of large-scale microbial co-occurrence and association networks. Among the many analytical techniques available, the Local Similarity Analysis (LSA) method is unique in that it captures local and potentially time-delayed co-occurrence and association patterns in time series data that cannot otherwise be identified by ordinary correlation analysis. However LSA, as originally developed, does not consider time series data with replicates, which hinders the full exploitation of available information. With replicates, it is possible to understand the variability of local similarity (LS) score and to obtain its confidence interval. We extended our LSA technique to time series data with replicates and termed it extended LSA, or eLSA. Simulations showed the capability of eLSA to capture subinterval and time-delayed associations. We implemented the eLSA technique into an easy-to-use analytic software package. The software pipeline integrates data normalization, statistical correlation calculation, statistical significance evaluation, and association network construction steps. We applied the eLSA technique to microbial community and gene expression datasets, where unique time-dependent associations were identified. The extended LSA analysis technique was demonstrated to reveal statistically significant local and potentially time-delayed association patterns in replicated time series data beyond that of ordinary correlation analysis. These statistically significant associations can provide insights to the real dynamics of biological systems. The newly designed eLSA software efficiently streamlines the analysis and is freely available from the eLSA homepage, which can be accessed at http://meta.usc.edu/softs/lsa.

Envelhecimento ativo e sua relação com a independência funcional

OpenAIRE

Ferreira, Olívia Galvão Lucena; Maciel, Silvana Carneiro; Costa, Sônia Maria Gusmão; Silva, Antonia Oliveira; Moreira, Maria Adelaide Silva Paredes

2012-01-01

O objetivo da presente pesquisa foi analisar os fatores determinantes de um envelhecimento ativo e sua relação com a independência funcional. A pesquisa foi realizada com 100 idosos de uma Unidade de Saúde da Família, em João Pessoa-PB. Como instrumentos para a avaliação dos idosos foram utilizados a Medida de Independência Funcional e um questionário sociodemográfico. Os dados foram analisados através do software SPSS. De acordo com os resultados, todos os idosos apresentaram independência f...

Year Ahead Demand Forecast of City Natural Gas Using Seasonal Time Series Methods

Directory of Open Access Journals (Sweden)

Mustafa Akpinar

2016-09-01

, when there is only consumption data in hand, all methods provide satisfying results and the differences between each method is very low. If a statistical software tool is not used, time series decomposition, the most primitive method, or Winters exponential smoothing requiring little mathematical knowledge for natural gas demand forecasting can be used with spreadsheet software. A statistical software tool containing ARIMA will obtain the best results.

Space Flight Software Development Software for Intelligent System Health Management

Science.gov (United States)

Trevino, Luis C.; Crumbley, Tim

2004-01-01

The slide presentation examines the Marshall Space Flight Center Flight Software Branch, including software development projects, mission critical space flight software development, software technical insight, advanced software development technologies, and continuous improvement in the software development processes and methods.

Auditor’s Risk Assessment of Independent Directors in Nigeria

Directory of Open Access Journals (Sweden)

Salau Abdulmalik

2017-01-01

Full Text Available The objective of this study is to investigate the external auditor’s risk assessment of independent directors in Nigeria. The study utilized data from 94 non-financial listed companies on the Nigerian Stock Exchange for the periods 2008-2013. The study used cross-sectional time-series feasible generalized least square regression, which account for heteroscedasticity and autocorrelation to test the influence independent non-executive director on auditor pricing decision in Nigeria. Our result indicates that the proportion of independent non-executive director has a positive relationship with audit fees, suggesting that this class of directors is priced high by the Nigerian auditors. These findings have both policy and practical implication on corporate governance. For instance, future regulatory reforms could consider collaborative board model instead of the insistence on more independent director presence in the boardroom.

Some recent developments in treatment planning software and methodology for BNCT

International Nuclear Information System (INIS)

Nigg, D.W.; Wheeler, F.J.; Wessol, D.E.; Wemple, C.A.; Babcock, R.; Capala, J.

1996-01-01

Over the past several years/the Idaho National Engineering Laboratory (INEL) has led the development of a unique, internationally-recognized set of software modules (BNCT rtpe) for computational dosimetry and treatment planning for Boron Neutron Capture Therapy (BNCT). The computational capability represented by this software is essential to the proper administration of all forms of radiotherapy for cancer. Such software addresses the need to perform pretreatment computation and optimization of the radiation dose distribution in the target volume. This permits the achievement of the optimal therapeutic ratio (tumor dose relative to critical normal tissue dose) for each individual patient via a systematic procedure for specifying the appropriate irradiation parameters to be employed for a given treatment. These parameters include angle of therapy beam incidence, beam aperture and shape,and beam intensity as a function of position across the beam front. The INEL software is used for treatment planning in the current series of human glioma trials at Brookhaven National Laboratory (BNL) and has also been licensed for research and developmental purposes to several other BNCT research centers in the US and in Europe

Some recent developments in treatment planning software and methodology for BNCT

International Nuclear Information System (INIS)

Nigg, D.W.; Wheeler, F.J.; Wessol, D.E.

1996-01-01

Over the past several years the Idaho National Engineering Laboratory (INEL) has led the development of a unique, internationally-recognized set of software modules (BNCT-rtpe) for computational dosimetry and treatment planning for Boron Neutron Capture Therapy (BNCT). The computational capability represented by this software is essential to the proper administration of all forms of radiotherapy for cancer. Such software addresses the need to perform pretreatment computation and optimization of the radiation dose distribution in the target volume. This permits the achievement of the optimal therapeutic ratio (tumor dose relative to critical normal tissue dose) for each individual patient via a systematic procedure for specifying the appropriate irradiation parameters to be employed for a given treatment. These parameters include angle of therapy beam incidence, beam aperture and shape, and beam intensity as a function of position across the beam front. The INEL software is used for treatment planning in the current series of human glioma trials at Brookhaven National Laboratory (BNL) and has also been licensed for research and developmental purposes to several other BNCT research centers in the US and in Europe

Tcl as a Software Environment for a TCS

Science.gov (United States)

Terrett, David L.

2002-12-01

This paper describes how the Tcl scripting language and C API has been used as the software environment for a telescope pointing kernel so that new pointing algorithms and software architectures can be developed and tested without needing a real-time operating system or real-time software environment. It has enabled development to continue outside the framework of a specific telescope project while continuing to build a system that is sufficiently complete to be capable of controlling real hardware but expending minimum effort on replacing the services that would normally by provided by a real-time software environment. Tcl is used as a scripting language for configuring the system at startup and then as the command interface for controlling the running system; the Tcl C language API is used to provided a system independent interface to file and socket I/O and other operating system services. The pointing algorithms themselves are implemented as a set of C++ objects calling C library functions that implement the algorithms described in [2]. Although originally designed as a test and development environment, the system, running as a soft real-time process on Linux, has been used to test the SOAR mount control system and will be used as the pointing kernel of the SOAR telescope control system

MetaComp: comprehensive analysis software for comparative meta-omics including comparative metagenomics.

Science.gov (United States)

Zhai, Peng; Yang, Longshu; Guo, Xiao; Wang, Zhe; Guo, Jiangtao; Wang, Xiaoqi; Zhu, Huaiqiu

2017-10-02

During the past decade, the development of high throughput nucleic sequencing and mass spectrometry analysis techniques have enabled the characterization of microbial communities through metagenomics, metatranscriptomics, metaproteomics and metabolomics data. To reveal the diversity of microbial communities and interactions between living conditions and microbes, it is necessary to introduce comparative analysis based upon integration of all four types of data mentioned above. Comparative meta-omics, especially comparative metageomics, has been established as a routine process to highlight the significant differences in taxon composition and functional gene abundance among microbiota samples. Meanwhile, biologists are increasingly concerning about the correlations between meta-omics features and environmental factors, which may further decipher the adaptation strategy of a microbial community. We developed a graphical comprehensive analysis software named MetaComp comprising a series of statistical analysis approaches with visualized results for metagenomics and other meta-omics data comparison. This software is capable to read files generated by a variety of upstream programs. After data loading, analyses such as multivariate statistics, hypothesis testing of two-sample, multi-sample as well as two-group sample and a novel function-regression analysis of environmental factors are offered. Here, regression analysis regards meta-omic features as independent variable and environmental factors as dependent variables. Moreover, MetaComp is capable to automatically choose an appropriate two-group sample test based upon the traits of input abundance profiles. We further evaluate the performance of its choice, and exhibit applications for metagenomics, metaproteomics and metabolomics samples. MetaComp, an integrative software capable for applying to all meta-omics data, originally distills the influence of living environment on microbial community by regression analysis

Experience with case tools in the design of process-oriented software

Science.gov (United States)

Novakov, Ognian; Sicard, Claude-Henri

1994-12-01

In Accelerator systems such as the CERN PS complex, process equipment has a life time which may exceed the typical life cycle of its related software. Taking into account the variety of such equipment, it is important to keep the analysis and design of the software in a system-independent form. This paper discusses the experience gathered in using commercial CASE tools for analysis, design and reverse engineering of different process-oriented software modules, with a principal emphasis on maintaining the initial analysis in a standardized form. Such tools have been in existence for several years, but this paper shows that they are not fully adapted to our needs. In particular, the paper stresses the problems of integrating such a tool into an existing data-base-dependent development chain, the lack of real-time simulation tools and of Object-Oriented concepts in existing commercial packages. Finally, the paper gives a broader view of software engineering needs in our particular context.

ALFA: The new ALICE-FAIR software framework

Science.gov (United States)

Al-Turany, M.; Buncic, P.; Hristov, P.; Kollegger, T.; Kouzinopoulos, C.; Lebedev, A.; Lindenstruth, V.; Manafov, A.; Richter, M.; Rybalchenko, A.; Vande Vyvre, P.; Winckler, N.

2015-12-01

The commonalities between the ALICE and FAIR experiments and their computing requirements led to the development of large parts of a common software framework in an experiment independent way. The FairRoot project has already shown the feasibility of such an approach for the FAIR experiments and extending it beyond FAIR to experiments at other facilities[1, 2]. The ALFA framework is a joint development between ALICE Online- Offline (O2) and FairRoot teams. ALFA is designed as a flexible, elastic system, which balances reliability and ease of development with performance using multi-processing and multithreading. A message- based approach has been adopted; such an approach will support the use of the software on different hardware platforms, including heterogeneous systems. Each process in ALFA assumes limited communication and reliance on other processes. Such a design will add horizontal scaling (multiple processes) to vertical scaling provided by multiple threads to meet computing and throughput demands. ALFA does not dictate any application protocols. Potentially, any content-based processor or any source can change the application protocol. The framework supports different serialization standards for data exchange between different hardware and software languages.

New software for neutron data reduction and visualization

International Nuclear Information System (INIS)

Worlton, T.; Chatterjee, A.; Hammonds, J.; Chen, D.; Loong, C.K.; Mikkelson, D.; Mikkelson, R.

2001-01-01

Development of advanced neutron sources and instruments has necessitated corresponding advances in software for neutron scattering data reduction and visualization. New sources produce datasets more rapidly, and new instruments produce large numbers of spectra. Because of the shorter collection times, users are able to make more measurements on a given sample. This rapid production of datasets requires that users be able to reduce and analyze data quickly to prevent a data bottleneck. In addition, the new sources and instruments are accommodating more users with less neutron-scattering specific expertise, which requires software that is easy to use and freely available. We have developed an Integrated Spectral Analysis Workbench (ISAW) software package to permit the rapid reduction and visualization of neutron data. It can handle large numbers of spectra and merge data from separate measurements. The data can be sorted according to any attribute and transformed in numerous ways. ISAW provides several views of the data that enable users to compare spectra and observe trends in the data. A command interpreter, which is now part of ISAW, allows scientists to easily set up a series of instrument-specific operations to reduce and visualize data automatically. ISAW is written entirely in Java to permit portability to different computer platforms and easy distribution of the software. The software was constructed using modern computer design methods to allow easy customization and improvement. ISAW currently only reads data from IPNS 'run' files, but work is underway to provide input of NeXus files. (author)

New software for neutron data reduction and visualization

Energy Technology Data Exchange (ETDEWEB)

Worlton, T.; Chatterjee, A.; Hammonds, J.; Chen, D.; Loong, C.K. [Argonne National Laboratory, Argonne, IL (United States); Mikkelson, D.; Mikkelson, R. [Univ. of Wisconsin-Stout, Menomonie, WI (United States)

2001-03-01

Development of advanced neutron sources and instruments has necessitated corresponding advances in software for neutron scattering data reduction and visualization. New sources produce datasets more rapidly, and new instruments produce large numbers of spectra. Because of the shorter collection times, users are able to make more measurements on a given sample. This rapid production of datasets requires that users be able to reduce and analyze data quickly to prevent a data bottleneck. In addition, the new sources and instruments are accommodating more users with less neutron-scattering specific expertise, which requires software that is easy to use and freely available. We have developed an Integrated Spectral Analysis Workbench (ISAW) software package to permit the rapid reduction and visualization of neutron data. It can handle large numbers of spectra and merge data from separate measurements. The data can be sorted according to any attribute and transformed in numerous ways. ISAW provides several views of the data that enable users to compare spectra and observe trends in the data. A command interpreter, which is now part of ISAW, allows scientists to easily set up a series of instrument-specific operations to reduce and visualize data automatically. ISAW is written entirely in Java to permit portability to different computer platforms and easy distribution of the software. The software was constructed using modern computer design methods to allow easy customization and improvement. ISAW currently only reads data from IPNS 'run' files, but work is underway to provide input of NeXus files. (author)

Software attribute visualization for high integrity software

Energy Technology Data Exchange (ETDEWEB)

Pollock, G.M.

1998-03-01

This report documents a prototype tool developed to investigate the use of visualization and virtual reality technologies for improving software surety confidence. The tool is utilized within the execution phase of the software life cycle. It provides a capability to monitor an executing program against prespecified requirements constraints provided in a program written in the requirements specification language SAGE. The resulting Software Attribute Visual Analysis Tool (SAVAnT) also provides a technique to assess the completeness of a software specification.

GIS-Based Noise Simulation Open Source Software: N-GNOIS

Science.gov (United States)

Vijay, Ritesh; Sharma, A.; Kumar, M.; Shende, V.; Chakrabarti, T.; Gupta, Rajesh

2015-12-01

Geographical information system (GIS)-based noise simulation software (N-GNOIS) has been developed to simulate the noise scenario due to point and mobile sources considering the impact of geographical features and meteorological parameters. These have been addressed in the software through attenuation modules of atmosphere, vegetation and barrier. N-GNOIS is a user friendly, platform-independent and open geospatial consortia (OGC) compliant software. It has been developed using open source technology (QGIS) and open source language (Python). N-GNOIS has unique features like cumulative impact of point and mobile sources, building structure and honking due to traffic. Honking is the most common phenomenon in developing countries and is frequently observed on any type of roads. N-GNOIS also helps in designing physical barrier and vegetation cover to check the propagation of noise and acts as a decision making tool for planning and management of noise component in environmental impact assessment (EIA) studies.

hctsa: A Computational Framework for Automated Time-Series Phenotyping Using Massive Feature Extraction.

Science.gov (United States)

Fulcher, Ben D; Jones, Nick S

2017-11-22

Phenotype measurements frequently take the form of time series, but we currently lack a systematic method for relating these complex data streams to scientifically meaningful outcomes, such as relating the movement dynamics of organisms to their genotype or measurements of brain dynamics of a patient to their disease diagnosis. Previous work addressed this problem by comparing implementations of thousands of diverse scientific time-series analysis methods in an approach termed highly comparative time-series analysis. Here, we introduce hctsa, a software tool for applying this methodological approach to data. hctsa includes an architecture for computing over 7,700 time-series features and a suite of analysis and visualization algorithms to automatically select useful and interpretable time-series features for a given application. Using exemplar applications to high-throughput phenotyping experiments, we show how hctsa allows researchers to leverage decades of time-series research to quantify and understand informative structure in time-series data. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Exploiting Software Tool Towards Easier Use And Higher Efficiency

Science.gov (United States)

Lin, G. H.; Su, J. T.; Deng, Y. Y.

2006-08-01

In developing countries, using data based on instrument made by themselves in maximum extent is very important. It is not only related to maximizing science returns upon prophase investment -- deep accumulations in every aspects but also science output. Based on the idea, we are exploiting a software (called THDP: Tool of Huairou Data Processing). It is used for processing a series of issues, which is met necessary in processing data. This paper discusses its designed purpose, functions, method and specialities. The primary vehicle for general data interpretation is through various techniques of data visualization, techniques of interactive. In the software, we employed Object Oriented approach. It is appropriate to the vehicle. it is imperative that the approach provide not only function, but do so in as convenient a fashion as possible. As result of the software exploiting, it is not only easier to learn data processing for beginner and more convenienter to need further improvement for senior but also increase greatly efficiency in every phrases include analyse, parameter adjusting, result display. Under frame of virtual observatory, for developing countries, we should study more and newer related technologies, which can advance ability and efficiency in science research, like the software we are developing

Software Comparison for Renewable Energy Deployment in a Distribution Network

Energy Technology Data Exchange (ETDEWEB)

Gao, David Wenzhong [Alternative Power Innovations, LLC, Sharonville, OH (United States); Muljadi, Eduard [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tian, Tian [National Renewable Energy Lab. (NREL), Golden, CO (United States); Miller, Mackay [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-02-22

The main objective of this report is to evaluate different software options for performing robust distributed generation (DG) power system modeling. The features and capabilities of four simulation tools, OpenDSS, GridLAB-D, CYMDIST, and PowerWorld Simulator, are compared to analyze their effectiveness in analyzing distribution networks with DG. OpenDSS and GridLAB-D, two open source software, have the capability to simulate networks with fluctuating data values. These packages allow the running of a simulation each time instant by iterating only the main script file. CYMDIST, a commercial software, allows for time-series simulation to study variations on network controls. PowerWorld Simulator, another commercial tool, has a batch mode simulation function through the 'Time Step Simulation' tool, which obtains solutions for a list of specified time points. PowerWorld Simulator is intended for analysis of transmission-level systems, while the other three are designed for distribution systems. CYMDIST and PowerWorld Simulator feature easy-to-use graphical user interfaces (GUIs). OpenDSS and GridLAB-D, on the other hand, are based on command-line programs, which increase the time necessary to become familiar with the software packages.

Newsroom Democracy: The Case for Independence of the Press. Monograph Series, No. 2.

Science.gov (United States)

Schwoebel, Jean; Hardt, Hanno, Ed.

Today there is a growing realization among journalists that providing information should be a real service in the public interest, which is free from the domination of private interests, and that there should be structures that guarantee the independence of journalists and the promotion of responsible and responsive journalism. In France, the…

Have You Heard This? Designing Mobile Social Software

Directory of Open Access Journals (Sweden)

Jørn Georg Sannes Knutsen

2010-07-01

Full Text Available ‘Desktop’ social networking services are migrating to mobile devices. Research into the design of mobile social software (MoSoSo, especially its communication design, is emerging. The case we present is from a collaborative, interdisciplinary research project into communicative design innovation concerning these technologies. In focus is the design of what we label the communicative prototype for an interaction and media centred view of social software development. This view is applied to an exploratory design research case that extends an established online social service to the iPhone/iPod platform. The conceptual design in the case is intended to enable the discovery of independent, non-commercial music. The projected service was developed in consultation with a national public service broadcaster. We frame the design and analysis within a sociocultural approach to mediated communication and research by design. We employ mixed methods both in design and in research. We argue that a communicative stance in early concept development offers valuable insights on the ongoing design of social software. The communication expertise of interaction designers is central to this.

The design of software system of intelligentized γ-camera

International Nuclear Information System (INIS)

Zhao Shujun; Li Suxiao; Wang Jing

2006-01-01

The software system of γ-camera adopts visualizing and interactive human-computer interface, collecting and displaying the data of patients in real time. Through a series of dealing with the collected data then it put out the medical record in Chinese. This system also can retrieve and backup the data of patients. Besides, it can assist the doctor to diagnose the illness by applying the clinical quantitative analysis function of the system. (authors)

Image analysis software versus direct anthropometry for breast measurements.

Science.gov (United States)

Quieregatto, Paulo Rogério; Hochman, Bernardo; Furtado, Fabianne; Machado, Aline Fernanda Perez; Sabino Neto, Miguel; Ferreira, Lydia Masako

2014-10-01

To compare breast measurements performed using the software packages ImageTool(r), AutoCAD(r) and Adobe Photoshop(r) with direct anthropometric measurements. Points were marked on the breasts and arms of 40 volunteer women aged between 18 and 60 years. When connecting the points, seven linear segments and one angular measurement on each half of the body, and one medial segment common to both body halves were defined. The volunteers were photographed in a standardized manner. Photogrammetric measurements were performed by three independent observers using the three software packages and compared to direct anthropometric measurements made with calipers and a protractor. Measurements obtained with AutoCAD(r) were the most reproducible and those made with ImageTool(r) were the most similar to direct anthropometry, while measurements with Adobe Photoshop(r) showed the largest differences. Except for angular measurements, significant differences were found between measurements of line segments made using the three software packages and those obtained by direct anthropometry. AutoCAD(r) provided the highest precision and intermediate accuracy; ImageTool(r) had the highest accuracy and lowest precision; and Adobe Photoshop(r) showed intermediate precision and the worst accuracy among the three software packages.

Software cost/resource modeling: Software quality tradeoff measurement

Science.gov (United States)

Lawler, R. W.

1980-01-01

A conceptual framework for treating software quality from a total system perspective is developed. Examples are given to show how system quality objectives may be allocated to hardware and software; to illustrate trades among quality factors, both hardware and software, to achieve system performance objectives; and to illustrate the impact of certain design choices on software functionality.

Qt based control system software for Low Energy Accelerator Facility

International Nuclear Information System (INIS)

Basu, A.; Singh, S.; Nagraju, S.B.V.; Gupta, S.; Singh, P.

2012-01-01

Qt based control system software for Low Energy Accelerating Facility (LEAF) is operational at Bhabha Atomic Research Centre (BARC), Trombay, Mumbai. LEAF is a 50 keV negative ion electrostatic accelerator based on SNICS ion source. Control system uses Nokia Trolltech's QT 4.x API for control system software. Ni 6008 USB based multifunction cards has been used for control and read back field equipments such as power supplies, pumps, valves etc. Control system architecture is designed to be client server. Qt is chosen for its excellent GUI capability and platform independent nature. Control system follows client server architecture. The paper will describe the control system. (author)

The software and algorithms for hyperspectral data processing

Science.gov (United States)

Shyrayeva, Anhelina; Martinov, Anton; Ivanov, Victor; Katkovsky, Leonid

2017-04-01

Hyperspectral remote sensing technique is widely used for collecting and processing -information about the Earth's surface objects. Hyperspectral data are combined to form a three-dimensional (x, y, λ) data cube. Department of Aerospace Research of the Institute of Applied Physical Problems of the Belarusian State University presents a general model of the software for hyperspectral image data analysis and processing. The software runs in Windows XP/7/8/8.1/10 environment on any personal computer. This complex has been has been written in C++ language using QT framework and OpenGL for graphical data visualization. The software has flexible structure that consists of a set of independent plugins. Each plugin was compiled as Qt Plugin and represents Windows Dynamic library (dll). Plugins can be categorized in terms of data reading types, data visualization (3D, 2D, 1D) and data processing The software has various in-built functions for statistical and mathematical analysis, signal processing functions like direct smoothing function for moving average, Savitzky-Golay smoothing technique, RGB correction, histogram transformation, and atmospheric correction. The software provides two author's engineering techniques for the solution of atmospheric correction problem: iteration method of refinement of spectral albedo's parameters using Libradtran and analytical least square method. The main advantages of these methods are high rate of processing (several minutes for 1 GB data) and low relative error in albedo retrieval (less than 15%). Also, the software supports work with spectral libraries, region of interest (ROI) selection, spectral analysis such as cluster-type image classification and automatic hypercube spectrum comparison by similarity criterion with similar ones from spectral libraries, and vice versa. The software deals with different kinds of spectral information in order to identify and distinguish spectrally unique materials. Also, the following advantages

Composing simulations using persistent software components

Energy Technology Data Exchange (ETDEWEB)

Holland, J.V.; Michelsen, R.E.; Powell, D.R.; Upton, S.C.; Thompson, D.R.

1999-03-01

The traditional process for developing large-scale simulations is cumbersome, time consuming, costly, and in some cases, inadequate. The topics of software components and component-based software engineering are being explored by software professionals in academic and industrial settings. A component is a well-delineated, relatively independent, and replaceable part of a software system that performs a specific function. Many researchers have addressed the potential to derive a component-based approach to simulations in general, and a few have focused on military simulations in particular. In a component-based approach, functional or logical blocks of the simulation entities are represented as coherent collections of components satisfying explicitly defined interface requirements. A simulation is a top-level aggregate comprised of a collection of components that interact with each other in the context of a simulated environment. A component may represent a simulation artifact, an agent, or any entity that can generated events affecting itself, other simulated entities, or the state of the system. The component-based approach promotes code reuse, contributes to reducing time spent validating or verifying models, and promises to reduce the cost of development while still delivering tailored simulations specific to analysis questions. The Integrated Virtual Environment for Simulation (IVES) is a composition-centered framework to achieve this potential. IVES is a Java implementation of simulation composition concepts developed at Los Alamos National Laboratory for use in several application domains. In this paper, its use in the military domain is demonstrated via the simulation of dismounted infantry in an urban environment.

Software structure for tritium-in-air monitoring in classified locations

International Nuclear Information System (INIS)

Ionete, Eusebiu Ilarian; Benchea, Dumitru

2009-01-01

Full text: In the working areas of heavy water detritiation facilities, were hydrogen gas is generated, the risk of air-hydrogen explosive mixture production is present. This paper gives the description of a software architecture solution for a fixed area tritium-in-air monitoring system suitable to be used in such hazardous locations. Tritium-in-air monitoring system was designed as a distributed system containing a number of fixed tritium in air monitoring units, each of them being composed of an ionisation chamber flow-through type and a fix sampling unit with a number of sample lines and one additional blow line. For each unit, software and hardware architecture structure enable independent performance with a fail-safe concept, remote control operation and data storage in a DCS-DCU module. This software architecture secures the setting possibility of alarm levels for tritium concentration, graphical visualisation and acoustic alarm in the case of level overtaking. The afferent software architecture contains applications in connection with hardware architecture and with a hydrogen detection system: RU-1 software application for control sampling; RU-2 software application for measured values display; RU-3 software application for remote data display; RU-4 software application for SQL conversion server; RU-5 software application for OPC standard conversion. The interconnection of all hardware components, between each PLC and each display unit, between tritium-in-air monitoring units and PLC sampling units will be internally carried out using interfaces. The interconnection between PLCs and tritium-in-air monitoring DCU will be made using a communication network, for instance Ethernet Profibus or RS 485. (authors)

Calculation Software versus Illustration Software for Teaching Statistics

DEFF Research Database (Denmark)

Mortensen, Peter Stendahl; Boyle, Robin G.

1999-01-01

As personal computers have become more and more powerful, so have the software packages available to us for teaching statistics. This paper investigates what software packages are currently being used by progressive statistics instructors at university level, examines some of the deficiencies...... of such software, and indicates features that statistics instructors wish to have incorporated in software in the future. The basis of the paper is a survey of participants at ICOTS-5 (the Fifth International Conference on Teaching Statistics). These survey results, combined with the software based papers...

Automation of Flight Software Regression Testing

Science.gov (United States)

Tashakkor, Scott B.

2016-01-01

NASA is developing the Space Launch System (SLS) to be a heavy lift launch vehicle supporting human and scientific exploration beyond earth orbit. SLS will have a common core stage, an upper stage, and different permutations of boosters and fairings to perform various crewed or cargo missions. Marshall Space Flight Center (MSFC) is writing the Flight Software (FSW) that will operate the SLS launch vehicle. The FSW is developed in an incremental manner based on "Agile" software techniques. As the FSW is incrementally developed, testing the functionality of the code needs to be performed continually to ensure that the integrity of the software is maintained. Manually testing the functionality on an ever-growing set of requirements and features is not an efficient solution and therefore needs to be done automatically to ensure testing is comprehensive. To support test automation, a framework for a regression test harness has been developed and used on SLS FSW. The test harness provides a modular design approach that can compile or read in the required information specified by the developer of the test. The modularity provides independence between groups of tests and the ability to add and remove tests without disturbing others. This provides the SLS FSW team a time saving feature that is essential to meeting SLS Program technical and programmatic requirements. During development of SLS FSW, this technique has proved to be a useful tool to ensure all requirements have been tested, and that desired functionality is maintained, as changes occur. It also provides a mechanism for developers to check functionality of the code that they have developed. With this system, automation of regression testing is accomplished through a scheduling tool and/or commit hooks. Key advantages of this test harness capability includes execution support for multiple independent test cases, the ability for developers to specify precisely what they are testing and how, the ability to add

Advances in model-based software for simulating ultrasonic immersion inspections of metal components

Science.gov (United States)

Chiou, Chien-Ping; Margetan, Frank J.; Taylor, Jared L.; Engle, Brady J.; Roberts, Ronald A.

2018-04-01

Under the sponsorship of the National Science Foundation's Industry/University Cooperative Research Center at ISU, an effort was initiated in 2015 to repackage existing research-grade software into user-friendly tools for the rapid estimation of signal-to-noise ratio (SNR) for ultrasonic inspections of metals. The software combines: (1) a Python-based graphical user interface for specifying an inspection scenario and displaying results; and (2) a Fortran-based engine for computing defect signals and backscattered grain noise characteristics. The later makes use the Thompson-Gray measurement model for the response from an internal defect, and the Thompson-Margetan independent scatterer model for backscattered grain noise. This paper, the third in the series [1-2], provides an overview of the ongoing modeling effort with emphasis on recent developments. These include the ability to: (1) treat microstructures where grain size, shape and tilt relative to the incident sound direction can all vary with depth; and (2) simulate C-scans of defect signals in the presence of backscattered grain noise. The simulation software can now treat both normal and oblique-incidence immersion inspections of curved metal components. Both longitudinal and shear-wave inspections are treated. The model transducer can either be planar, spherically-focused, or bi-cylindrically-focused. A calibration (or reference) signal is required and is used to deduce the measurement system efficiency function. This can be "invented" by the software using center frequency and bandwidth information specified by the user, or, alternatively, a measured calibration signal can be used. Defect types include flat-bottomed-hole reference reflectors, and spherical pores and inclusions. Simulation outputs include estimated defect signal amplitudes, root-mean-square values of grain noise amplitudes, and SNR as functions of the depth of the defect within the metal component. At any particular depth, the user can view

Metronome LKM: An open source virtual keyboard driver to measure experiment software latencies.

Science.gov (United States)

Garaizar, Pablo; Vadillo, Miguel A

2017-10-01

Experiment software is often used to measure reaction times gathered with keyboards or other input devices. In previous studies, the accuracy and precision of time stamps has been assessed through several means: (a) generating accurate square wave signals from an external device connected to the parallel port of the computer running the experiment software, (b) triggering the typematic repeat feature of some keyboards to get an evenly separated series of keypress events, or (c) using a solenoid handled by a microcontroller to press the input device (keyboard, mouse button, touch screen) that will be used in the experimental setup. Despite the advantages of these approaches in some contexts, none of them can isolate the measurement error caused by the experiment software itself. Metronome LKM provides a virtual keyboard to assess an experiment's software. Using this open source driver, researchers can generate keypress events using high-resolution timers and compare the time stamps collected by the experiment software with those gathered by Metronome LKM (with nanosecond resolution). Our software is highly configurable (in terms of keys pressed, intervals, SysRq activation) and runs on 2.6-4.8 Linux kernels.

Software system safety

Science.gov (United States)

Uber, James G.

1988-01-01

Software itself is not hazardous, but since software and hardware share common interfaces there is an opportunity for software to create hazards. Further, these software systems are complex, and proven methods for the design, analysis, and measurement of software safety are not yet available. Some past software failures, future NASA software trends, software engineering methods, and tools and techniques for various software safety analyses are reviewed. Recommendations to NASA are made based on this review.

A PLC platform-independent structural analysis on FBD programs for digital reactor protection systems

International Nuclear Information System (INIS)

Jung, Sejin; Yoo, Junbeom; Lee, Young-Jun

2017-01-01

Highlights: • FBD has been widely used to implement safety-critical software for PLC-based systems. • The safety-critical software should be developed strictly with safety programming guidelines. • There are no argued rules that have specific links to higher guidelines NUREG/CR-6463 PLC platform-independently. • This paper proposes a set of rules on the structure of FBD programs with providing specific links to higher guidelines. • This paper also provides CASE tool ‘FBD Checker’ for analyzing the structure of FBD. - Abstract: FBD (function block diagram) has been widely used to implement safety-critical software for PLC (programmable logic controller)-based digital nuclear reactor protection systems. The software should be developed strictly in accordance with safety programming guidelines such as NUREG/CR-6463. Software engineering tools of PLC vendors enable us to present structural analyses using FBD programs, but specific rules pertaining to the guidelines are enclosed within the commercial tools, and specific links to the guidelines are not clearly communicated. This paper proposes a set of rules on the structure of FBD programs in accordance with guidelines, and we develop an automatic analysis tool for FBD programs written in the PLCopen TC6 format. With the proposed tool, any FBD program that is transformed into an open format can be analyzed the PLC platform-independently. We consider a case study on FBD programs obtained from a preliminary version of a Korean nuclear power plant, and we demonstrate the effectiveness and potential of the proposed rules and analysis tool.

SU-E-T-455: Impact of Different Independent Dose Verification Software Programs for Secondary Check

International Nuclear Information System (INIS)

Itano, M; Yamazaki, T; Kosaka, M; Kobayashi, N; Yamashita, M; Ishibashi, S; Higuchi, Y; Tachibana, H

2015-01-01

Purpose: There have been many reports for different dose calculation algorithms for treatment planning system (TPS). Independent dose verification program (IndpPro) is essential to verify clinical plans from the TPS. However, the accuracy of different independent dose verification programs was not evident. We conducted a multi-institutional study to reveal the impact of different IndpPros using different TPSs. Methods: Three institutes participated in this study. They used two different IndpPros (RADCALC and Simple MU Analysis (SMU), which implemented the Clarkson algorithm. RADCALC needed the input of radiological path length (RPL) computed by the TPSs (Eclipse or Pinnacle3). SMU used CT images to compute the RPL independently from TPS). An ion-chamber measurement in water-equivalent phantom was performed to evaluate the accuracy of two IndpPros and the TPS in each institute. Next, the accuracy of dose calculation using the two IndpPros compared to TPS was assessed in clinical plan. Results: The accuracy of IndpPros and the TPSs in the homogenous phantom was +/−1% variation to the measurement. 1543 treatment fields were collected from the patients treated in the institutes. The RADCALC showed better accuracy (0.9 ± 2.2 %) than the SMU (1.7 ± 2.1 %). However, the accuracy was dependent on the TPS (Eclipse: 0.5%, Pinnacle3: 1.0%). The accuracy of RADCALC with Eclipse was similar to that of SMU in one of the institute. Conclusion: Depending on independent dose verification program, the accuracy shows systematic dose accuracy variation even though the measurement comparison showed a similar variation. The variation was affected by radiological path length calculation. IndpPro with Pinnacle3 has different variation because Pinnacle3 computed the RPL using physical density. Eclipse and SMU uses electron density, though

Configurable software for satellite graphics

Energy Technology Data Exchange (ETDEWEB)

Hartzman, P D

1977-12-01

An important goal in interactive computer graphics is to provide users with both quick system responses for basic graphics functions and enough computing power for complex calculations. One solution is to have a distributed graphics system in which a minicomputer and a powerful large computer share the work. The most versatile type of distributed system is an intelligent satellite system in which the minicomputer is programmable by the application user and can do most of the work while the large remote machine is used for difficult computations. At New York University, the hardware was configured from available equipment. The level of system intelligence resulted almost completely from software development. Unlike previous work with intelligent satellites, the resulting system had system control centered in the satellite. It also had the ability to reconfigure software during realtime operation. The design of the system was done at a very high level using set theoretic language. The specification clearly illustrated processor boundaries and interfaces. The high-level specification also produced a compact, machine-independent virtual graphics data structure for picture representation. The software was written in a systems implementation language; thus, only one set of programs was needed for both machines. A user can program both machines in a single language. Tests of the system with an application program indicate that is has very high potential. A major result of this work is the demonstration that a gigantic investment in new hardware is not necessary for computing facilities interested in graphics.

Downsizer - A Graphical User Interface-Based Application for Browsing, Acquiring, and Formatting Time-Series Data for Hydrologic Modeling

Science.gov (United States)

Ward-Garrison, Christian; Markstrom, Steven L.; Hay, Lauren E.

2009-01-01

The U.S. Geological Survey Downsizer is a computer application that selects, downloads, verifies, and formats station-based time-series data for environmental-resource models, particularly the Precipitation-Runoff Modeling System. Downsizer implements the client-server software architecture. The client presents a map-based, graphical user interface that is intuitive to modelers; the server provides streamflow and climate time-series data from over 40,000 measurement stations across the United States. This report is the Downsizer user's manual and provides (1) an overview of the software design, (2) installation instructions, (3) a description of the graphical user interface, (4) a description of selected output files, and (5) troubleshooting information.

Multifractal analysis of managed and independent float exchange rates

Science.gov (United States)

Stošić, Darko; Stošić, Dusan; Stošić, Tatijana; Stanley, H. Eugene

2015-06-01

We investigate multifractal properties of daily price changes in currency rates using the multifractal detrended fluctuation analysis (MF-DFA). We analyze managed and independent floating currency rates in eight countries, and determine the changes in multifractal spectrum when transitioning between the two regimes. We find that after the transition from managed to independent float regime the changes in multifractal spectrum (position of maximum and width) indicate an increase in market efficiency. The observed changes are more pronounced for developed countries that have a well established trading market. After shuffling the series, we find that the multifractality is due to both probability density function and long term correlations for managed float regime, while for independent float regime multifractality is in most cases caused by broad probability density function.

RAVE-a Detector-independent vertex reconstruction toolkit

Energy Technology Data Exchange (ETDEWEB)

Waltenberger, Wolfgang [Institute of High Energy Physics, Austrian Academy of Sciences A-1050 Vienna (Austria)], E-mail: walten@hephy.oeaw.ac.at; Mitaroff, Winfried; Moser, Fabian [Institute of High Energy Physics, Austrian Academy of Sciences A-1050 Vienna (Austria)

2007-10-21

A detector-independent toolkit for vertex reconstruction (RAVE) is being developed, along with a standalone framework (VERTIGO) for testing, analyzing and debugging. The core algorithms represent state of the art for geometric vertex finding and fitting by both linear (Kalman filter) and robust estimation methods. Main design goals are ease of use, flexibility for embedding into existing software frameworks, extensibility, and openness. The implementation is based on modern object-oriented techniques, is coded in C++ with interfaces for Java and Python, and follows an open-source approach. A beta release is available.

RAVE-a Detector-independent vertex reconstruction toolkit

International Nuclear Information System (INIS)

Waltenberger, Wolfgang; Mitaroff, Winfried; Moser, Fabian

2007-01-01

A detector-independent toolkit for vertex reconstruction (RAVE) is being developed, along with a standalone framework (VERTIGO) for testing, analyzing and debugging. The core algorithms represent state of the art for geometric vertex finding and fitting by both linear (Kalman filter) and robust estimation methods. Main design goals are ease of use, flexibility for embedding into existing software frameworks, extensibility, and openness. The implementation is based on modern object-oriented techniques, is coded in C++ with interfaces for Java and Python, and follows an open-source approach. A beta release is available

Avoidable Software Procurements

Science.gov (United States)

2012-09-01

software license, software usage, ELA, Software as a Service , SaaS , Software Asset...PaaS Platform as a Service SaaS Software as a Service SAM Software Asset Management SMS System Management Server SEWP Solutions for Enterprise Wide...delivery of full Cloud Services , we will see the transition of the Cloud Computing service model from Iaas to SaaS , or Software as a Service . Software

The D OE software trigger

International Nuclear Information System (INIS)

Linnemann, J.T.; Michigan State Univ., East Lansing, MI

1992-10-01

In the D OE experiment, the software filter operates in a processor farm with each node processing a single event. Processing is data-driven: the filter does local processing to verify the candidates from the hardware trigger. The filter code consists of independent pieces called ''tools''; processing for a given hardware bit is a ''script'' invoking one or more ''tools'' sequentially. An offline simulator drives the same code with the same configuration files, running on real or simulated data. Online tests use farm nodes parasiting on the data stream. We discuss the performance of the system and how we attempt to verify its correctness

Timing system control software in the SLC

International Nuclear Information System (INIS)

Thompson, K.; Phinney, N.

1985-04-01

A new timing system that allows precision (approx.1 to 2 ns) control of the trigger times of klystrons, beam position monitors, and other devices on a pulse-to-pulse basis at up to 360 Hz is in operation in the first third of the SLAC linear accelerator. The control software is divided between a central host VAX and local Intel 8086-based microprocessor clusters. Facilities exist to set up and adjust the timing of devices or groups of devices independently for beam pulses having different destinations and purposes, which are run in an interlaced fashion during normal machine operation. Upgrading of the system is currently underway, using a new version of the Programmable Delay Unit CAMAC module to allow pipelining of timing information for three machine pulses. An overview of the current state of the system is presented in this paper, with an emphasis on software control

Advances in Multimedia, Software Engineering and Computing Vol.1 : Proceedings of the 2011 MSEC International Conference on Multimedia, Software Engineering and Computing

CERN Document Server

Lin, Sally

2012-01-01

MSEC2011 is an integrated conference concentrating its focus upon Multimedia ,Software Engineering, Computing and Education. In the proceeding, you can learn much more knowledge about Multimedia, Software Engineering ,Computing and Education of researchers all around the world. The main role of the proceeding is to be used as an exchange pillar for researchers who are working in the mentioned field. In order to meet high standard of Springer, AISC series ,the organization committee has made their efforts to do the following things. Firstly, poor quality paper has been refused after reviewing course by anonymous referee experts. Secondly, periodically review meetings have been held around the reviewers about five times for exchanging reviewing suggestions. Finally, the conference organization had several preliminary sessions before the conference. Through efforts of different people and departments, the conference will be successful and fruitful.

Advances in Multimedia, Software Engineering and Computing Vol.2 : Proceedings of the 2011 MSEC International Conference on Multimedia, Software Engineering and Computing

CERN Document Server

Lin, Sally

2012-01-01

MSEC2011 is an integrated conference concentrating its focus upon Multimedia ,Software Engineering, Computing and Education. In the proceeding, you can learn much more knowledge about Multimedia, Software Engineering, Computing and Education of researchers all around the world. The main role of the proceeding is to be used as an exchange pillar for researchers who are working in the mentioned field. In order to meet high standard of Springer, AISC series ,the organization committee has made their efforts to do the following things. Firstly, poor quality paper has been refused after reviewing course by anonymous referee experts. Secondly, periodically review meetings have been held around the reviewers about five times for exchanging reviewing suggestions. Finally, the conference organization had several preliminary sessions before the conference. Through efforts of different people and departments, the conference will be successful and fruitful.

Damping Inter-area Oscillations using Static Synchronous Series Compensator (SSSC)

DEFF Research Database (Denmark)

Su, Chi; Chen, Zhe

2011-01-01

Static synchronous series compensator (SSSC) has the ability to emulate a reactance in series with the connected transmission line. When fed with some supplementary signals from the connected system, SSSC is able to participate in the power system inter-area oscillation damping by changing...... the compensated reactance. This paper analyses the influence of SSSC on power system small signal stability. A SSSC damping controller scheme is presented and discussed. In DIgSILENT PowerFactory software, modal analysis and time-domain simulation are conducted in a single-machine infinite bus system model...... and a four-machine two-area test system model to verify and improve the damping controller scheme....

Current trends in hardware and software for brain-computer interfaces (BCIs).

Science.gov (United States)

Brunner, P; Bianchi, L; Guger, C; Cincotti, F; Schalk, G

2011-04-01

A brain-computer interface (BCI) provides a non-muscular communication channel to people with and without disabilities. BCI devices consist of hardware and software. BCI hardware records signals from the brain, either invasively or non-invasively, using a series of device components. BCI software then translates these signals into device output commands and provides feedback. One may categorize different types of BCI applications into the following four categories: basic research, clinical/translational research, consumer products, and emerging applications. These four categories use BCI hardware and software, but have different sets of requirements. For example, while basic research needs to explore a wide range of system configurations, and thus requires a wide range of hardware and software capabilities, applications in the other three categories may be designed for relatively narrow purposes and thus may only need a very limited subset of capabilities. This paper summarizes technical aspects for each of these four categories of BCI applications. The results indicate that BCI technology is in transition from isolated demonstrations to systematic research and commercial development. This process requires several multidisciplinary efforts, including the development of better integrated and more robust BCI hardware and software, the definition of standardized interfaces, and the development of certification, dissemination and reimbursement procedures.

Current trends in hardware and software for brain-computer interfaces (BCIs)

Science.gov (United States)

Brunner, P.; Bianchi, L.; Guger, C.; Cincotti, F.; Schalk, G.

2011-04-01

A brain-computer interface (BCI) provides a non-muscular communication channel to people with and without disabilities. BCI devices consist of hardware and software. BCI hardware records signals from the brain, either invasively or non-invasively, using a series of device components. BCI software then translates these signals into device output commands and provides feedback. One may categorize different types of BCI applications into the following four categories: basic research, clinical/translational research, consumer products, and emerging applications. These four categories use BCI hardware and software, but have different sets of requirements. For example, while basic research needs to explore a wide range of system configurations, and thus requires a wide range of hardware and software capabilities, applications in the other three categories may be designed for relatively narrow purposes and thus may only need a very limited subset of capabilities. This paper summarizes technical aspects for each of these four categories of BCI applications. The results indicate that BCI technology is in transition from isolated demonstrations to systematic research and commercial development. This process requires several multidisciplinary efforts, including the development of better integrated and more robust BCI hardware and software, the definition of standardized interfaces, and the development of certification, dissemination and reimbursement procedures.

Software engineering

CERN Document Server

Sommerville, Ian

2010-01-01

The ninth edition of Software Engineering presents a broad perspective of software engineering, focusing on the processes and techniques fundamental to the creation of reliable, software systems. Increased coverage of agile methods and software reuse, along with coverage of 'traditional' plan-driven software engineering, gives readers the most up-to-date view of the field currently available. Practical case studies, a full set of easy-to-access supplements, and extensive web resources make teaching the course easier than ever.

BiGGEsTS: integrated environment for biclustering analysis of time series gene expression data

Directory of Open Access Journals (Sweden)

Madeira Sara C

2009-07-01

Full Text Available Abstract Background The ability to monitor changes in expression patterns over time, and to observe the emergence of coherent temporal responses using expression time series, is critical to advance our understanding of complex biological processes. Biclustering has been recognized as an effective method for discovering local temporal expression patterns and unraveling potential regulatory mechanisms. The general biclustering problem is NP-hard. In the case of time series this problem is tractable, and efficient algorithms can be used. However, there is still a need for specialized applications able to take advantage of the temporal properties inherent to expression time series, both from a computational and a biological perspective. Findings BiGGEsTS makes available state-of-the-art biclustering algorithms for analyzing expression time series. Gene Ontology (GO annotations are used to assess the biological relevance of the biclusters. Methods for preprocessing expression time series and post-processing results are also included. The analysis is additionally supported by a visualization module capable of displaying informative representations of the data, including heatmaps, dendrograms, expression charts and graphs of enriched GO terms. Conclusion BiGGEsTS is a free open source graphical software tool for revealing local coexpression of genes in specific intervals of time, while integrating meaningful information on gene annotations. It is freely available at: http://kdbio.inesc-id.pt/software/biggests. We present a case study on the discovery of transcriptional regulatory modules in the response of Saccharomyces cerevisiae to heat stress.

Formation of heterogeneous magmatic series beneath North Santorini, South Aegean island arc

DEFF Research Database (Denmark)

Bailey, John C; Jensen, E.S.; Hansen, A.

2008-01-01

magma formation beneath North Santorini throughout its 500 ka history is attributed to variable transfer of sedimentary components - either terrigenous or pelagic, as bulk sediments or high-temperature partial melts rather than fluids or low-temperature partial melts - from a rupture zone...... in the subducted slab to the overlying mantle. The three main magmatic series followed independent paths of assimilation of upper crustal materials during fractional crystallization. Assimilation was more pronounced at the basaltic stage. The long-lived histories of the three main magmatic series imply repetitive...... melting of isolated mantle regions, ascent of magmas through independent feeder systems, and their residence in separate crustal magma chambers....

Physician use of updated anti-virus software in a tertiary Nigerian hospital.

Science.gov (United States)

Laabes, E P; Nyango, D D; Ayedima, M M; Ladep, N G

2010-01-01

While physicians are becoming increasingly dependent on computers and the internet, highly lethal malware continue to be loaded into cyberspace. We sought to assess the proportion of physicians with updated anti-virus software in Jos University Teaching Hospital Nigeria and to determine perceived barriers to getting updates. We used a pre-tested semi-structured self-administered questionnaire to conduct a cross-sectional survey among 118 physicians. The mean age (+/- SD) of subjects was 34 (+/- 4) years, with 94 male and 24 female physicians. Forty-two (36.5%) of 115 physicians with anti-virus software used an updated program (95% Cl: 27, 45). The top-three antivirus software were: McAfee 40 (33.9%), AVG 37 (31.4%) and Norton 17 (14.4%). Common infections were: Trojan horse 22 (29.7%), Brontok worm 8 (10.8%), and Ravmonlog.exe 5 (6.8%). Internet browsing with a firewall was an independent determinant for use of updated anti-virus software [OR 4.3, 95% CI, 1.86, 10.02; P malware producers and anti-virus software developers.

A multi-center study benchmarks software tools for label-free proteome quantification

Science.gov (United States)

Gillet, Ludovic C; Bernhardt, Oliver M.; MacLean, Brendan; Röst, Hannes L.; Tate, Stephen A.; Tsou, Chih-Chiang; Reiter, Lukas; Distler, Ute; Rosenberger, George; Perez-Riverol, Yasset; Nesvizhskii, Alexey I.; Aebersold, Ruedi; Tenzer, Stefan

2016-01-01

The consistent and accurate quantification of proteins by mass spectrometry (MS)-based proteomics depends on the performance of instruments, acquisition methods and data analysis software. In collaboration with the software developers, we evaluated OpenSWATH, SWATH2.0, Skyline, Spectronaut and DIA-Umpire, five of the most widely used software methods for processing data from SWATH-MS (sequential window acquisition of all theoretical fragment ion spectra), a method that uses data-independent acquisition (DIA) for label-free protein quantification. We analyzed high-complexity test datasets from hybrid proteome samples of defined quantitative composition acquired on two different MS instruments using different SWATH isolation windows setups. For consistent evaluation we developed LFQbench, an R-package to calculate metrics of precision and accuracy in label-free quantitative MS, and report the identification performance, robustness and specificity of each software tool. Our reference datasets enabled developers to improve their software tools. After optimization, all tools provided highly convergent identification and reliable quantification performance, underscoring their robustness for label-free quantitative proteomics. PMID:27701404

Loss of ability to work and ability to live independently in Parkinson's disease.

Science.gov (United States)

Jasinska-Myga, Barbara; Heckman, Michael G; Wider, Christian; Putzke, John D; Wszolek, Zbigniew K; Uitti, Ryan J

2012-02-01

Ability to work and live independently is of particular concern for patients with Parkinson's disease (PD). We studied a series of PD patients able to work or live independently at baseline, and evaluated potential risk factors for two separate outcomes: loss of ability to work and loss of ability to live independently. The series comprised 495 PD patients followed prospectively. Ability to work and ability to live independently were based on clinical interview and examination. Cox regression models adjusted for age and disease duration were used to evaluate associations of baseline characteristics with loss of ability to work and loss of ability to live independently. Higher UPDRS dyskinesia score, UPDRS instability score, UPDRS total score, Hoehn and Yahr stage, and presence of intellectual impairment at baseline were all associated with increased risk of future loss of ability to work and loss of ability to live independently (P ≤ 0.0033). Five years after initial visit, for patients ≤70 years of age with a disease duration ≤4 years at initial visit, 88% were still able to work and 90% to live independently. These estimates worsened as age and disease duration at initial visit increased; for patients >70 years of age with a disease duration >4 years, estimates at 5 years were 43% able to work and 57% able to live independently. The information provided in this study can offer useful information for PD patients in preparing for future ability to perform activities of daily living. Copyright © 2011 Elsevier Ltd. All rights reserved.

How to statistically analyze nano exposure measurement results: Using an ARIMA time series approach

NARCIS (Netherlands)

Klein Entink, R.H.; Fransman, W.; Brouwer, D.H.

2011-01-01

Measurement strategies for exposure to nano-sized particles differ from traditional integrated sampling methods for exposure assessment by the use of real-time instruments. The resulting measurement series is a time series, where typically the sequential measurements are not independent from each

Requisite Information Collaboration and Distributed Knowledge Management in Software Development

DEFF Research Database (Denmark)

Petersen, Mogens K.; Bjørn, Pernille; Frank, L.

distributed knowledge management product state models. The paper draws upon a series of discussion with Scandinavian IT Group (SIG). With an interest in how performance in their new organization develops SIG invited the research group to study measures of organizational performance and the use and effect...... of knowledge management tools in software development. The paper does not represent the viewpoint of SIG but outline our framework and major research questions....

Treatment delivery software for a new clinical grade ultrasound system for thermoradiotherapy.

Science.gov (United States)

Novák, Petr; Moros, Eduardo G; Straube, William L; Myerson, Robert J

2005-11-01

A detailed description of a clinical grade Scanning Ultrasound Reflector Linear Array System (SURLAS) applicator was given in a previous paper [Med. Phys. 32, 230-240 (2005)]. In this paper we concentrate on the design, development, and testing of the personal computer (PC) based treatment delivery software that runs the therapy system. The SURLAS requires the coordinated interaction between the therapy applicator and several peripheral devices for its proper and safe operation. One of the most important tasks was the coordination of the input power sequences for the elements of two parallel opposed ultrasound arrays (eight 1.5 cm x 2 cm elements/array, array 1 and 2 operate at 1.9 and 4.9 MHz, respectively) in coordination with the position of a dual-face scanning acoustic reflector. To achieve this, the treatment delivery software can divide the applicator's treatment window in up to 64 sectors (minimum size of 2 cm x 2 cm), and control the power to each sector independently by adjusting the power output levels from the channels of a 16-channel radio-frequency generator. The software coordinates the generator outputs with the position of the reflector as it scans back and forth between the arrays. Individual sector control and dual frequency operation allows the SURLAS to adjust power deposition in three dimensions to superficial targets coupled to its treatment window. The treatment delivery software also monitors and logs several parameters such as temperatures acquired using a 16-channel thermocouple thermometry unit. Safety (in particular to patients) was the paramount concern and design criterion. Failure mode and effects analysis (FMEA) was applied to the applicator as well as to the entire therapy system in order to identify safety issues and rank their relative importance. This analysis led to the implementation of several safety mechanisms and a software structure where each device communicates with the controlling PC independently of the others. In case

Free software, Open source software, licenses. A short presentation including a procedure for research software and data dissemination

OpenAIRE

Gomez-Diaz , Teresa

2014-01-01

4 pages. Spanish version: Software libre, software de código abierto, licencias. Donde se propone un procedimiento de distribución de software y datos de investigación; The main goal of this document is to help the research community to understand the basic concepts of software distribution: Free software, Open source software, licenses. This document also includes a procedure for research software and data dissemination.

A model perception on the independence of PhD students in ...

African Journals Online (AJOL)

Amy Stambach

A model perception on the independence of PhD students in promoting the ... At school of postgraduate studies, all academic documents related to PhD ..... Workshop series sponsored by the counseling center at the University of Illinois in ...

Promoting linguistic complexity, greater message length and ease of engagement in email writing in people with aphasia: initial evidence from a study utilizing assistive writing software.

Science.gov (United States)

Thiel, Lindsey; Sage, Karen; Conroy, Paul

2017-01-01

Improving email writing in people with aphasia could enhance their ability to communicate, promote interaction and reduce isolation. Spelling therapies have been effective in improving single-word writing. However, there has been limited evidence on how to achieve changes to everyday writing tasks such as email writing in people with aphasia. One potential area that has been largely unexplored in the literature is the potential use of assistive writing technologies, despite some initial evidence that assistive writing software use can lead to qualitative and quantitative improvements to spontaneous writing. This within-participants case series design study aimed to investigate the effects of using assistive writing software to improve email writing in participants with dysgraphia related to aphasia. Eight participants worked through a hierarchy of writing tasks of increasing complexity within broad topic areas that incorporate the spheres of writing need of the participants: writing for domestic needs, writing for social needs and writing for business/administrative needs. Through completing these tasks, participants had the opportunity to use the various functions of the software, such as predictive writing, word banks and text to speech. Therapy also included training and practice in basic computer and email skills to encourage increased independence. Outcome measures included email skills, keyboard skills, email writing and written picture description tasks, and a perception of disability assessment. Four of the eight participants showed statistically significant improvements to spelling accuracy within emails when using the software. At a group level there was a significant increase in word length with the software; while four participants showed noteworthy changes to the range of word classes used. Enhanced independence in email use and improvements in participants' perceptions of their writing skills were also noted. This study provided some initial evidence

Proposals for software analysis of cost effectiveness and cost-benefit for optimisation of radiation protection

International Nuclear Information System (INIS)

Schieber, C.; Lombard, J.; Lefaure, C.

1990-06-01

The objective of this report is to present the principles of decision making software for radiation protection option, applying ALARA principle. The choice of optimum options is performed by applying the models of cost effectiveness and cost-benefit. Options of radiation protection are described by two indicators: a simple economic indicator: cost of radiation protection; and dosimetry indicator: collective dose related to protection. For both analyses the software enables sensitivity analysis. It would be possible to complete the software by integrating a module which would take into account combinations of two options since they are not independent

Pascal software structures achieve definite control of the 24 MFTF sustaining neutral-beam power supplies

International Nuclear Information System (INIS)

Anon.

1982-01-01

Precise control of large, complex systems is not assured unless there is known to be no unintended interactions in the control system. The software controlling the sustaining neutral-beam power supplies of the Mirror Fusion Test Facility accomplishes this feat. The software structures comprise some 16,000 lines of commented Pascal code, distributed amoung 10 different tasks. Each task may control any of the 24 power supplies. All the tasks are strictly event-driven, and are not subject to any system mode. Since there is no global information in the software, we know that all the power supplies are controlled independently

Efficient Algorithms for Segmentation of Item-Set Time Series

Science.gov (United States)

Chundi, Parvathi; Rosenkrantz, Daniel J.

We propose a special type of time series, which we call an item-set time series, to facilitate the temporal analysis of software version histories, email logs, stock market data, etc. In an item-set time series, each observed data value is a set of discrete items. We formalize the concept of an item-set time series and present efficient algorithms for segmenting a given item-set time series. Segmentation of a time series partitions the time series into a sequence of segments where each segment is constructed by combining consecutive time points of the time series. Each segment is associated with an item set that is computed from the item sets of the time points in that segment, using a function which we call a measure function. We then define a concept called the segment difference, which measures the difference between the item set of a segment and the item sets of the time points in that segment. The segment difference values are required to construct an optimal segmentation of the time series. We describe novel and efficient algorithms to compute segment difference values for each of the measure functions described in the paper. We outline a dynamic programming based scheme to construct an optimal segmentation of the given item-set time series. We use the item-set time series segmentation techniques to analyze the temporal content of three different data sets—Enron email, stock market data, and a synthetic data set. The experimental results show that an optimal segmentation of item-set time series data captures much more temporal content than a segmentation constructed based on the number of time points in each segment, without examining the item set data at the time points, and can be used to analyze different types of temporal data.

Evaluation procedure of software requirements specification for digital I and C of KNGR

International Nuclear Information System (INIS)

Lee, Jang Soo; Park, Jong Kyun; Lee, Ki Young; Kim, Jang Yeol; Cheon, Se Woo

2001-06-01

The accuracy of the specification of requirements of a digital system is of prime importance to the acceptance and success of the system. The development, use, and regulation of computer systems in nuclear reactor Instrumentation and Control (I and C) systems to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Korean Next Generation Reactor (KNGR) Software Safety Verification and Validation (SSVV) Task, Korea Atomic Energy Research Institute, which investigates different aspects of computer software in reactor I and C systems, and describes the engineering procedures for developing such a software. The purpose of this guideline is to give the software safety evaluator the trail map between the code and standards layer and the design methodology and documents layer for the software important to safety in nuclear power plants. Recently, the requirements specification of safety-critical software systems and safety analysis of them are being recognized as one of the important issues in the software life cycle, and being developed new regulatory positions and standards by the regulatory and the standardization organizations such as IAEA, IEC, and IEEE. We presented the procedure for evaluating the software requirements specifications of the KNGR protection systems. We believe it can be useful for both licenser and licensee to conduct an evaluation of the safety in the requirements phase of developing the software. The guideline consists of the requirements engineering for software of KNGR protection systems in chapter 1, the evaluation checklist of software requirements specification in chapter2.3, and the safety evaluation procedure of KNGR software requirements specification in chapter 2.4

Two‐year experience with the commercial Gamma Knife Check software

Science.gov (United States)

Bhatnagar, Jagdish; Bednarz, Greg; Novotny, Josef; Flickinger, John; Lunsford, L. Dade; Huq, M. Saiful

2016-01-01

The Gamma Knife Check software is an FDA approved second check system for dose calculations in Gamma Knife radiosurgery. The purpose of this study was to evaluate the accuracy and the stability of the commercial software package as a tool for independent dose verification. The Gamma Knife Check software version 8.4 was commissioned for a Leksell Gamma Knife Perfexion and a 4C unit at the University of Pittsburgh Medical Center in May 2012. Independent dose verifications were performed using this software for 319 radiosurgery cases on the Perfexion and 283 radiosurgery cases on the 4C units. The cases on each machine were divided into groups according to their diagnoses, and an averaged absolute percent dose difference for each group was calculated. The percentage dose difference for each treatment target was obtained as the relative difference between the Gamma Knife Check dose and the dose from the tissue maximum ratio algorithm (TMR 10) from the GammaPlan software version 10 at the reference point. For treatment plans with imaging skull definition, results obtained from the Gamma Knife Check software using the measurement‐based skull definition method are used for comparison. The collected dose difference data were also analyzed in terms of the distance from the treatment target to the skull, the number of treatment shots used for the target, and the gamma angles of the treatment shots. The averaged percent dose differences between the Gamma Knife Check software and the GammaPlan treatment planning system are 0.3%, 0.89%, 1.24%, 1.09%, 0.83%, 0.55%, 0.33%, and 1.49% for the trigeminal neuralgia, acoustic neuroma, arteriovenous malformation (AVM), meningioma, pituitary adenoma, glioma, functional disorders, and metastasis cases on the Perfexion unit. The corresponding averaged percent dose differences for the 4C unit are 0.33%, 1.2%, 2.78% 1.99%, 1.4%, 1.92%, 0.62%, and 1.51%, respectively. The dose difference is, in general, larger for treatment targets in the

Impact of Agile Software Development Model on Software Maintainability

Science.gov (United States)

Gawali, Ajay R.

2012-01-01

Software maintenance and support costs account for up to 60% of the overall software life cycle cost and often burdens tightly budgeted information technology (IT) organizations. Agile software development approach delivers business value early, but implications on software maintainability are still unknown. The purpose of this quantitative study…

A Sandwich-Type Standard Error Estimator of SEM Models with Multivariate Time Series

Science.gov (United States)

Zhang, Guangjian; Chow, Sy-Miin; Ong, Anthony D.

2011-01-01

Structural equation models are increasingly used as a modeling tool for multivariate time series data in the social and behavioral sciences. Standard error estimators of SEM models, originally developed for independent data, require modifications to accommodate the fact that time series data are inherently dependent. In this article, we extend a…

Quantification frameworks and their application for evaluating the software quality factor using quality characteristic value

International Nuclear Information System (INIS)

Kim, C.; Chung, C.H.; Won-Ahn, K.

2004-01-01

Many problems, related with safety, frequently occur because Digital Instrument and Control Systems are widely used and expanding their ranges to many applications in Nuclear Power Plants. It, however, does not hold a general position to estimate an appropriate software quality. Thus, the Quality Characteristic Value, a software quality factor through each software life cycle, is suggested in this paper. The Quality Characteristic Value is obtained as following procedure: 1) Scoring Quality Characteristic Factors (especially correctness, traceability, completeness, and understandability) onto Software Verification and Validation results, 2) Deriving the diamond-shaped graphs by setting values of Factors at each axis and lining every points, and lastly 3) Measuring the area of the graph for Quality Characteristic Value. In this paper, this methodology is applied to Plant Control System. In addition, the series of quantification frameworks exhibit some good characteristics in the view of software quality factor. More than any thing else, it is believed that introduced framework may be applicable to regulatory guide, software approval procedures, due to its soundness and simple characteristics. (authors)

Software design practice using two SCADA software packages

DEFF Research Database (Denmark)

Basse, K.P.; Christensen, Georg Kronborg; Frederiksen, P. K.

1996-01-01

Typical software development for manufacturing control is done either by specialists with consideral real-time programming experience or done by the adaptation of standard software packages for manufacturing control. After investigation and test of two commercial software packages: "InTouch" and ......Touch" and "Fix", it is argued, that a more efficient software solution can be achieved by utilising an integrated specification for SCADA and PLC-programming. Experiences gained from process control is planned investigated for descrete parts manufacturing....

Y2K - an oil and gas software vendor's perspective

International Nuclear Information System (INIS)

Stewart, L.D.

1998-01-01

Oil and gas companies have begun to deal with third party software vendors to increase their efficiency and to concentrate on their core business. When it comes to dealing with year 2000 (Y2K) problems, information technology (IT) departments will have to deal with complex heterogeneous systems and long lists of independent software vendors and suppliers. This paper highlighted some of the unique issues that should be considered when testing any heterogeneous oil and gas system for Y2K. Most petroleum companies and vendors have established Y2K compliance teams with plans involving three major phases: (1) testing and identification of problems, (2) correction and avoidance of problems, and (3) preparation for recovery from unidentified problems

Software reliability

CERN Document Server

Bendell, A

1986-01-01

Software Reliability reviews some fundamental issues of software reliability as well as the techniques, models, and metrics used to predict the reliability of software. Topics covered include fault avoidance, fault removal, and fault tolerance, along with statistical methods for the objective assessment of predictive accuracy. Development cost models and life-cycle cost models are also discussed. This book is divided into eight sections and begins with a chapter on adaptive modeling used to predict software reliability, followed by a discussion on failure rate in software reliability growth mo

The control software framework of the web base

International Nuclear Information System (INIS)

Nakatani, Takeshi; Inamura, Yasuhiro; Ito, Takayoshi; Otomo, Toshiya

2015-01-01

Web browsers are one of the most platform-independent user interfaces. In particular, web pages created using responsive web design (RWD) are available for use on desktop and laptop computers, as well as tablet terminals and smart phones. We developed a common software framework, IROHA, for the instrument control system in the Materials and Life Science Experimental Facility at the Japan Proton Accelerator Research Complex to build a flexible and scalable system by adopting XML/HTTP. However, its user interface was platform-dependent, and we wanted it to be more user-friendly. In 2013, we developed the prototype of a new software framework, IROHA2, comprising several device control servers and an instrument management server, retaining the flexibility and scalability of IROHA. We also adopted the Bootstrap framework to create an RWD user interface for these servers. (author)

Software Epistemology

Science.gov (United States)

2016-03-01

in-vitro decision to incubate a startup, Lexumo [7], which is developing a commercial Software as a Service ( SaaS ) vulnerability assessment...LTS Label Transition System MUSE Mining and Understanding Software Enclaves RTEMS Real-Time Executive for Multi-processor Systems SaaS Software ...as a Service SSA Static Single Assignment SWE Software Epistemology UD/DU Def-Use/Use-Def Chains (Dataflow Graph)

Technical Evaluation Report 25: Open Source Software: Two learning management systems

Directory of Open Access Journals (Sweden)

Jim Depow

2003-10-01

Full Text Available This report is the second in a two-part series about open source (OSS and free software (FS systems in online education. These are rapidly emerging as alternatives to costly proprietary learning management systems (LMS and content management systems (CMS. This report reviews two LMS systems and one CMS system, all developed on the OSS/ FS principle and available to users free of charge.

Guidance and Control Software Project Data - Volume 4: Configuration Management and Quality Assurance Documents

Science.gov (United States)

Hayhurst, Kelly J. (Editor)

2008-01-01

The Guidance and Control Software (GCS) project was the last in a series of software reliability studies conducted at Langley Research Center between 1977 and 1994. The technical results of the GCS project were recorded after the experiment was completed. Some of the support documentation produced as part of the experiment, however, is serving an unexpected role far beyond its original project context. Some of the software used as part of the GCS project was developed to conform to the RTCA/DO-178B software standard, "Software Considerations in Airborne Systems and Equipment Certification," used in the civil aviation industry. That standard requires extensive documentation throughout the software development life cycle, including plans, software requirements, design and source code, verification cases and results, and configuration management and quality control data. The project documentation that includes this information is open for public scrutiny without the legal or safety implications associated with comparable data from an avionics manufacturer. This public availability has afforded an opportunity to use the GCS project documents for DO-178B training. This report provides a brief overview of the GCS project, describes the 4-volume set of documents and the role they are playing in training, and includes configuration management and quality assurance documents from the GCS project. Volume 4 contains six appendices: A. Software Accomplishment Summary for the Guidance and Control Software Project; B. Software Configuration Index for the Guidance and Control Software Project; C. Configuration Management Records for the Guidance and Control Software Project; D. Software Quality Assurance Records for the Guidance and Control Software Project; E. Problem Report for the Pluto Implementation of the Guidance and Control Software Project; and F. Support Documentation Change Reports for the Guidance and Control Software Project.

Computer software.

Science.gov (United States)

Rosenthal, L E

1986-10-01

Software is the component in a computer system that permits the hardware to perform the various functions that a computer system is capable of doing. The history of software and its development can be traced to the early nineteenth century. All computer systems are designed to utilize the "stored program concept" as first developed by Charles Babbage in the 1850s. The concept was lost until the mid-1940s, when modern computers made their appearance. Today, because of the complex and myriad tasks that a computer system can perform, there has been a differentiation of types of software. There is software designed to perform specific business applications. There is software that controls the overall operation of a computer system. And there is software that is designed to carry out specialized tasks. Regardless of types, software is the most critical component of any computer system. Without it, all one has is a collection of circuits, transistors, and silicone chips.

Three novel software tools for ASDEX Upgrade

International Nuclear Information System (INIS)

Martinov, S.; Löbhard, T.; Lunt, T.; Behler, K.; Drube, R.; Eixenberger, H.; Herrmann, A.; Lohs, A.; Lüddecke, K.; Merkel, R.; Neu, G.; ASDEX Upgrade Team; MPCDF Garching

2016-01-01

Highlights: • Key features of innovative software tools for data visualization and inspection are presented to the nuclear fusion research community. • 3D animation of experiment geometry together with diagnostic data and images allow better understanding of measurements and influence of machine construction details behind them. • Multi-video viewer with fusion relevant image manipulation abilities and event database features allows faster and better decision making from video streams coming from various plasma and machine diagnostics. • Platform independant Web technologies enable the inspection of diagnostic raw signals with virtually any kind of display device. - Abstract: Visualization of measurements together with experimental settings is a general subject in experiments analysis. The complex engineering design, 3D geometry, and manifold of diagnostics in larger fusion research experiments justify the development of special analysis and visualization programs. Novel ASDEX Upgrade (AUG) software tools bring together virtual navigation through 3D device models and advanced play-back and interpretation of video streams from plasma discharges. A third little tool allows the web-based platform independent observation of real-time diagnostic signals. While all three tools stem from spontaneous development ideas and are not considered mission critical for the operation of a fusion device, they with time and growing completeness shaped up as valuable helpers to visualize acquired data in fusion research. A short overview on the goals, the features, and the design as well as the operation of these tools is given in this paper.

Three novel software tools for ASDEX Upgrade

Energy Technology Data Exchange (ETDEWEB)

Martinov, S. [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, D-85748 Garching bei München (Germany); Löbhard, T. [Conovum GmbH & Co. KG, Nymphenburger Straße 13, D-80335 München (Germany); Lunt, T. [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, D-85748 Garching bei München (Germany); Behler, K., E-mail: karl.behler@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, D-85748 Garching bei München (Germany); Drube, R.; Eixenberger, H.; Herrmann, A.; Lohs, A. [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, D-85748 Garching bei München (Germany); Lüddecke, K. [Unlimited Computer Systems GmbH, Seeshaupterstr. 15, D-82393 Iffeldorf (Germany); Merkel, R.; Neu, G.; ASDEX Upgrade Team [Max-Planck-Institut für Plasmaphysik, Boltzmannstr. 2, D-85748 Garching bei München (Germany); MPCDF Garching [Max Planck Compu ting and Data Facility, Boltzmannstr. 2, D-85748 Garching (Germany)

2016-11-15

Highlights: • Key features of innovative software tools for data visualization and inspection are presented to the nuclear fusion research community. • 3D animation of experiment geometry together with diagnostic data and images allow better understanding of measurements and influence of machine construction details behind them. • Multi-video viewer with fusion relevant image manipulation abilities and event database features allows faster and better decision making from video streams coming from various plasma and machine diagnostics. • Platform independant Web technologies enable the inspection of diagnostic raw signals with virtually any kind of display device. - Abstract: Visualization of measurements together with experimental settings is a general subject in experiments analysis. The complex engineering design, 3D geometry, and manifold of diagnostics in larger fusion research experiments justify the development of special analysis and visualization programs. Novel ASDEX Upgrade (AUG) software tools bring together virtual navigation through 3D device models and advanced play-back and interpretation of video streams from plasma discharges. A third little tool allows the web-based platform independent observation of real-time diagnostic signals. While all three tools stem from spontaneous development ideas and are not considered mission critical for the operation of a fusion device, they with time and growing completeness shaped up as valuable helpers to visualize acquired data in fusion research. A short overview on the goals, the features, and the design as well as the operation of these tools is given in this paper.

System Quality Management in Software Testing Laboratory that Chooses Accreditation

Directory of Open Access Journals (Sweden)

Yanet Brito R.

2013-12-01

Full Text Available The evaluation of software products will reach full maturity when executed by the scheme and provides third party certification. For the validity of the certification, the independent laboratory must be accredited for that function, using internationally recognized standards. This brings with it a challenge for the Industrial Laboratory Testing Software (LIPS, responsible for testing the products developed in Cuban Software Industry, define strategies that will permit it to offer services with a high level of quality. Therefore it is necessary to establish a system of quality management according to NC-ISO/IEC 17025: 2006 to continuously improve the operational capacity and technical competence of the laboratory, with a view to future accreditation of tests performed. This article discusses the process defined in the LIPS for the implementation of a Management System of Quality, from the current standards and trends, as a necessary step to opt for the accreditation of the tests performed.

Dangers and uses of cross-correlation in analyzing time series in perception, performance, movement, and neuroscience: The importance of constructing transfer function autoregressive models.

Science.gov (United States)

Dean, Roger T; Dunsmuir, William T M

2016-06-01

Many articles on perception, performance, psychophysiology, and neuroscience seek to relate pairs of time series through assessments of their cross-correlations. Most such series are individually autocorrelated: they do not comprise independent values. Given this situation, an unfounded reliance is often placed on cross-correlation as an indicator of relationships (e.g., referent vs. response, leading vs. following). Such cross-correlations can indicate spurious relationships, because of autocorrelation. Given these dangers, we here simulated how and why such spurious conclusions can arise, to provide an approach to resolving them. We show that when multiple pairs of series are aggregated in several different ways for a cross-correlation analysis, problems remain. Finally, even a genuine cross-correlation function does not answer key motivating questions, such as whether there are likely causal relationships between the series. Thus, we illustrate how to obtain a transfer function describing such relationships, informed by any genuine cross-correlations. We illustrate the confounds and the meaningful transfer functions by two concrete examples, one each in perception and performance, together with key elements of the R software code needed. The approach involves autocorrelation functions, the establishment of stationarity, prewhitening, the determination of cross-correlation functions, the assessment of Granger causality, and autoregressive model development. Autocorrelation also limits the interpretability of other measures of possible relationships between pairs of time series, such as mutual information. We emphasize that further complexity may be required as the appropriate analysis is pursued fully, and that causal intervention experiments will likely also be needed.

DRUGDOG 3:0: U.S. Navy Random Urinalysis software package

OpenAIRE

Wilson, Dale E.

1994-01-01

Approved for public release; distribution is unlimited Although the United States Navy has had a mandatory Random Urinalysis Program in effect for many years, there has never been a formal, standardize methodology to implement the process. OPNAV INSTRUCTION 5350.4 (series) provides guidance on what must be accomplished, but not how to accomplish it. Automation and standardization of the program through software implementation can lend confidence to personnel who undergo urinalysis testing ...

Provenance tracking for scientific software toolchains through on-demand release and archiving

Science.gov (United States)

Ham, David

2017-04-01

There is an emerging consensus that published computational science results must be backed by a provenance chain tying results to the exact versions of input data and the code which generated them. There is also now an impressive range of web services devoted to revision control of software, and the archiving in citeable form of both software and input data. However, much scientific software itself builds on libraries and toolkits, and these themselves have dependencies. Further, it is common for cutting edge research to depend on the latest version of software in online repositories, rather than the official release version. This creates a situation in which an author who wishes to follow best practice in recording the provenance chain of their results must archive and cite unreleased versions of a series of dependencies. Here, we present an alternative which toolkit authors can easily implement to provide a semi-automatic mechanism for creating and archiving custom software releases of the precise version of a package used in a particular simulation. This approach leverages the excellent services provided by GitHub and Zenodo to generate a connected set of citeable DOIs for the archived software. We present the integration of this workflow into the Firedrake automated finite element framework as a practical example of this approach in use on a complex geoscientific tool chain in practical use.

Testing Separability and Independence of Perceptual Dimensions with General Recognition Theory: A Tutorial and New R Package (grtools).

Science.gov (United States)

Soto, Fabian A; Zheng, Emily; Fonseca, Johnny; Ashby, F Gregory

2017-01-01

Determining whether perceptual properties are processed independently is an important goal in perceptual science, and tools to test independence should be widely available to experimental researchers. The best analytical tools to test for perceptual independence are provided by General Recognition Theory (GRT), a multidimensional extension of signal detection theory. Unfortunately, there is currently a lack of software implementing GRT analyses that is ready-to-use by experimental psychologists and neuroscientists with little training in computational modeling. This paper presents grtools , an R package developed with the explicit aim of providing experimentalists with the ability to perform full GRT analyses using only a couple of command lines. We describe the software and provide a practical tutorial on how to perform each of the analyses available in grtools . We also provide advice to researchers on best practices for experimental design and interpretation of results when applying GRT and grtools .

Testing Separability and Independence of Perceptual Dimensions with General Recognition Theory: A Tutorial and New R Package (grtools

Directory of Open Access Journals (Sweden)

Fabian A. Soto

2017-05-01

Full Text Available Determining whether perceptual properties are processed independently is an important goal in perceptual science, and tools to test independence should be widely available to experimental researchers. The best analytical tools to test for perceptual independence are provided by General Recognition Theory (GRT, a multidimensional extension of signal detection theory. Unfortunately, there is currently a lack of software implementing GRT analyses that is ready-to-use by experimental psychologists and neuroscientists with little training in computational modeling. This paper presents grtools, an R package developed with the explicit aim of providing experimentalists with the ability to perform full GRT analyses using only a couple of command lines. We describe the software and provide a practical tutorial on how to perform each of the analyses available in grtools. We also provide advice to researchers on best practices for experimental design and interpretation of results when applying GRT and grtools

Independent measuring station for the GNEJS neutron spectrometer information and measurement system

International Nuclear Information System (INIS)

Gorokhov, I.S.; Laptev, A.B.; Marchenkov, V.V.; Tubol'tsev, Yu.V.; Fokin, E.Yu.; Shcherbakov, O.A.

1984-01-01

An independent measuring station (IMS) being a part of the information and measuring system of the neutron time-of-flight spectrometer is described. IMS represents the time (time-to-amplitude or time-to-angular) module analyzer assembled on the base of one or several CAMAC crates. The station permits to perform time measurements as well as the time measurements with amplitude weighing in an independent mode with subseqUent data transmission the central PDP-11/05 computer. The station processor unit is an independent controller. The software consists of the programming langUage of the controller from local terminal and programs ensuring measuring and shaping the spectra with their output on TV display devic. communication with the computer and dialogue with the operator

The RTC - a software support system for the control of the CERN SPS

International Nuclear Information System (INIS)

Herr, W.; Lauckner, R.; Morpurga, G.

1989-01-01

The RTC (Run Time Coordinator) is a software support system designed for the SPS control system to provide a runtime environment for application software. It coordinates the execution of individual programs or processes and supervises the process control, i.e. process synchronization, inter process communication, data transfer and operator I/O. This supervision includes the control of processes distributed on a UNIX based network. A standard language independent data interface is part of the system. The system includes tools for data presentation, error logging and contention resolution. This strategy of separating system dependent features from the body of the application programs leads to high flexibility and simplifies the software development. The basic philosophy of the RTC is discussed and its implementation is described. 7 refs

Software Engineering Guidebook

Science.gov (United States)

Connell, John; Wenneson, Greg

1993-01-01

The Software Engineering Guidebook describes SEPG (Software Engineering Process Group) supported processes and techniques for engineering quality software in NASA environments. Three process models are supported: structured, object-oriented, and evolutionary rapid-prototyping. The guidebook covers software life-cycles, engineering, assurance, and configuration management. The guidebook is written for managers and engineers who manage, develop, enhance, and/or maintain software under the Computer Software Services Contract.

From Software Development to Software Assembly

NARCIS (Netherlands)

Sneed, Harry M.; Verhoef, Chris

2016-01-01

The lack of skilled programming personnel and the growing burden of maintaining customized software are forcing organizations to quit producing their own software. It's high time they turned to ready-made, standard components to fulfill their business requirements. Cloud services might be one way to

Common Data Acquisition Systems (DAS) Software Development for Rocket Propulsion Test (RPT) Test Facilities

Science.gov (United States)

Hebert, Phillip W., Sr.; Davis, Dawn M.; Turowski, Mark P.; Holladay, Wendy T.; Hughes, Mark S.

2012-01-01

The advent of the commercial space launch industry and NASA's more recent resumption of operation of Stennis Space Center's large test facilities after thirty years of contractor control resulted in a need for a non-proprietary data acquisition systems (DAS) software to support government and commercial testing. The software is designed for modularity and adaptability to minimize the software development effort for current and future data systems. An additional benefit of the software's architecture is its ability to easily migrate to other testing facilities thus providing future commonality across Stennis. Adapting the software to other Rocket Propulsion Test (RPT) Centers such as MSFC, White Sands, and Plumbrook Station would provide additional commonality and help reduce testing costs for NASA. Ultimately, the software provides the government with unlimited rights and guarantees privacy of data to commercial entities. The project engaged all RPT Centers and NASA's Independent Verification & Validation facility to enhance product quality. The design consists of a translation layer which provides the transparency of the software application layers to underlying hardware regardless of test facility location and a flexible and easily accessible database. This presentation addresses system technical design, issues encountered, and the status of Stennis development and deployment.

A Software Reuse Approach and Its Effect On Software Quality, An Empirical Study for The Software Industry

OpenAIRE

Mateen, Ahmed; Kausar, Samina; Sattar, Ahsan Raza

2017-01-01

Software reusability has become much interesting because of increased quality and reduce cost. A good process of software reuse leads to enhance the reliability, productivity, quality and the reduction of time and cost. Current reuse techniques focuses on the reuse of software artifact which grounded on anticipated functionality whereas, the non-functional (quality) aspect are also important. So, Software reusability used here to expand quality and productivity of software. It improves overal...

Software quality assurance: in large scale and complex software-intensive systems

NARCIS (Netherlands)

Mistrik, I.; Soley, R.; Ali, N.; Grundy, J.; Tekinerdogan, B.

2015-01-01

Software Quality Assurance in Large Scale and Complex Software-intensive Systems presents novel and high-quality research related approaches that relate the quality of software architecture to system requirements, system architecture and enterprise-architecture, or software testing. Modern software

Great software debates

CERN Document Server

Davis, A

2004-01-01

The industry’s most outspoken and insightful critic explains how the software industry REALLY works. In Great Software Debates, Al Davis, shares what he has learned about the difference between the theory and the realities of business and encourages you to question and think about software engineering in ways that will help you succeed where others fail. In short, provocative essays, Davis fearlessly reveals the truth about process improvement, productivity, software quality, metrics, agile development, requirements documentation, modeling, software marketing and sales, empiricism, start-up financing, software research, requirements triage, software estimation, and entrepreneurship.

Computer-Aided Software Engineering - An approach to real-time software development

Science.gov (United States)

Walker, Carrie K.; Turkovich, John J.

1989-01-01

A new software engineering discipline is Computer-Aided Software Engineering (CASE), a technology aimed at automating the software development process. This paper explores the development of CASE technology, particularly in the area of real-time/scientific/engineering software, and a history of CASE is given. The proposed software development environment for the Advanced Launch System (ALS CASE) is described as an example of an advanced software development system for real-time/scientific/engineering (RT/SE) software. The Automated Programming Subsystem of ALS CASE automatically generates executable code and corresponding documentation from a suitably formatted specification of the software requirements. Software requirements are interactively specified in the form of engineering block diagrams. Several demonstrations of the Automated Programming Subsystem are discussed.

Model-Based Software Testing for Object-Oriented Software

Science.gov (United States)

Biju, Soly Mathew

2008-01-01

Model-based testing is one of the best solutions for testing object-oriented software. It has a better test coverage than other testing styles. Model-based testing takes into consideration behavioural aspects of a class, which are usually unchecked in other testing methods. An increase in the complexity of software has forced the software industry…

Software Atom: An approach towards software components structuring to improve reusability

Directory of Open Access Journals (Sweden)

Muhammad Hussain Mughal

2017-12-01

Full Text Available Diversity of application domain compelled to design sustainable classification scheme for significantly amassing software repository. The atomic reusable software components are articulated to improve the software component reusability in volatile industry.  Numerous approaches of software classification have been proposed over past decades. Each approach has some limitations related to coupling and cohesion. In this paper, we proposed a novel approach by constituting the software based on radical functionalities to improve software reusability. We analyze the element's semantics in Periodic Table used in chemistry to design our classification approach, and present this approach using tree-based classification to curtail software repository search space complexity and further refined based on semantic search techniques. We developed a Global unique Identifier (GUID for indexing the functions and related components. We have exploited the correlation between chemistry element and software elements to simulate one to one mapping between them. Our approach is inspired from sustainability chemical periodic table. We have proposed software periodic table (SPT representing atomic software components extracted from real application software. Based on SPT classified repository tree parsing & extraction to enable the user to program their software by customizing the ingredients of software requirements. The classified repository of software ingredients assist user to exploits their requirements to software engineer and enable requirement engineer to develop a rapid large-scale prototype with great essence. Furthermore, we would predict the usability of the categorized repository based on feedback of users.  The continuous evolution of that proposed repository will be fine-tuned based on utilization and SPT would be gradually optimized by ant colony optimization techniques. Succinctly would provoke automating the software development process.

Promoting Independent Performance of Transition-Related Tasks Using a Palmtop PC-Based Self-Directed Visual and Auditory Prompting System

Science.gov (United States)

Riffel, Laura A.; Wehmeyer, Michael L.; Turnbull, Ann P.; Lattimore, Jennifer; Davies, Daniel; Stock, Steven; Fisher, Sherilyn

2005-01-01

This study examined the use of a palmtop computer running a software program by transition-age students with cognitive disabilities to increase independence on vocational and independent living tasks. The purpose of this research was to test the hypotheses that a palmtop computer utilizing a Windows CE platform with touch screen capabilities and…

Proceedings of the Fifth Triennial Software Quality Forum 2000, Software for the Next Millennium, Software Quality Forum

Energy Technology Data Exchange (ETDEWEB)

Scientific Software Engineering Group, CIC-12

2000-04-01

The Software Quality Forum is a triennial conference held by the Software Quality Assurance Subcommittee for the Department of Energy's Quality Managers. The forum centers on key issues, information, and technology important in software development for the Nuclear Weapons Complex. This year it will be opened up to include local information technology companies and software vendors presenting their solutions, ideas, and lessons learned. The Software Quality Forum 2000 will take on a more hands-on, instructional tone than those previously held. There will be an emphasis on providing information, tools, and resources to assist developers in their goal of producing next generation software.

NASA software documentation standard software engineering program

Science.gov (United States)

1991-01-01

The NASA Software Documentation Standard (hereinafter referred to as Standard) can be applied to the documentation of all NASA software. This Standard is limited to documentation format and content requirements. It does not mandate specific management, engineering, or assurance standards or techniques. This Standard defines the format and content of documentation for software acquisition, development, and sustaining engineering. Format requirements address where information shall be recorded and content requirements address what information shall be recorded. This Standard provides a framework to allow consistency of documentation across NASA and visibility into the completeness of project documentation. This basic framework consists of four major sections (or volumes). The Management Plan contains all planning and business aspects of a software project, including engineering and assurance planning. The Product Specification contains all technical engineering information, including software requirements and design. The Assurance and Test Procedures contains all technical assurance information, including Test, Quality Assurance (QA), and Verification and Validation (V&V). The Management, Engineering, and Assurance Reports is the library and/or listing of all project reports.

Indefinite theta series and generalized error functions

CERN Document Server

Alexandrov, Sergei; Manschot, Jan; Pioline, Boris

2016-01-01

Theta series for lattices with indefinite signature $(n_+,n_-)$ arise in many areas of mathematics including representation theory and enumerative algebraic geometry. Their modular properties are well understood in the Lorentzian case ($n_+=1$), but have remained obscure when $n_+\\geq 2$. Using a higher-dimensional generalization of the usual (complementary) error function, discovered in an independent physics project, we construct the modular completion of a class of `conformal' holomorphic theta series ($n_+=2$). As an application, we determine the modular properties of a generalized Appell-Lerch sum attached to the lattice ${\\operatorname A}_2$, which arose in the study of rank 3 vector bundles on $\\mathbb{P}^2$. The extension of our method to $n_+>2$ is outlined.

QRev—Software for computation and quality assurance of acoustic doppler current profiler moving-boat streamflow measurements—Technical manual for version 2.8

Science.gov (United States)

Mueller, David S.

2016-06-21

The software program, QRev applies common and consistent computational algorithms combined with automated filtering and quality assessment of the data to improve the quality and efficiency of streamflow measurements and helps ensure that U.S. Geological Survey streamflow measurements are consistent, accurate, and independent of the manufacturer of the instrument used to make the measurement. Software from different manufacturers uses different algorithms for various aspects of the data processing and discharge computation. The algorithms used by QRev to filter data, interpolate data, and compute discharge are documented and compared to the algorithms used in the manufacturers’ software. QRev applies consistent algorithms and creates a data structure that is independent of the data source. QRev saves an extensible markup language (XML) file that can be imported into databases or electronic field notes software. This report is the technical manual for version 2.8 of QRev.

Science and Software

Science.gov (United States)

Zelt, C. A.

2017-12-01

Earth science attempts to understand how the earth works. This research often depends on software for modeling, processing, inverting or imaging. Freely sharing open-source software is essential to prevent reinventing the wheel and allows software to be improved and applied in ways the original author may never have envisioned. For young scientists, releasing software can increase their name ID when applying for jobs and funding, and create opportunities for collaborations when scientists who collect data want the software's creator to be involved in their project. However, we frequently hear scientists say software is a tool, it's not science. Creating software that implements a new or better way of earth modeling or geophysical processing, inverting or imaging should be viewed as earth science. Creating software for things like data visualization, format conversion, storage, or transmission, or programming to enhance computational performance, may be viewed as computer science. The former, ideally with an application to real data, can be published in earth science journals, the latter possibly in computer science journals. Citations in either case should accurately reflect the impact of the software on the community. Funding agencies need to support more software development and open-source releasing, and the community should give more high-profile awards for developing impactful open-source software. Funding support and community recognition for software development can have far reaching benefits when the software is used in foreseen and unforeseen ways, potentially for years after the original investment in the software development. For funding, an open-source release that is well documented should be required, with example input and output files. Appropriate funding will provide the incentive and time to release user-friendly software, and minimize the need for others to duplicate the effort. All funded software should be available through a single web site

Web software for the control and management of radiation protection devices in the Cadarache site

International Nuclear Information System (INIS)

Beltritti, F.

2010-01-01

This series of slides presents how to use a new software dedicated to the management of the periodical controls that have to be performed on the equipment involved in radiation protection. This software is ready to be dispatched on the CEA site of Cadarache. This software gives information on: the device to be controlled, the controls that have to be performed, the procedures to follow to make the test, the equipment necessary for the test particularly the need for radioactive sources, the maintenance of the device, the previous measurements and in the end the device's conformity. An evaluation of the conformity of all the devices present in a building or an area or of a particular type can be easily obtained. (A.C.)

Software for the IAEA Occupational Radiation Protection Standards

International Nuclear Information System (INIS)

Mocaun, N.M.; Paul, F.; Griffith, R.V.; Gustafsson, M.; Webb, G.A.M.; Enache, A.

2000-01-01

same approach will be used to provide other documents in the Safety Standards Series in computer accessible format. The software and development features will be described using a few screen images. (author)

Management of the Technological Innovation Process in Software Companies from Sinaloa, Mexico

Directory of Open Access Journals (Sweden)

Alejandra MIRANDA FELIX

2016-06-01

Full Text Available The objective of this paper is to explain the management process of technological innovation within certified software companies from Sinaloa, considering their strategic technology plan, innovative processes, and intellectual capital. This work is based on the study of 9 software companies located in Sinaloa and certified through the CMMI (Capability Maturity Model for Integration process. Their problems are grouped into three areas: 1 strategic technology plan, 2 innovation and 3 intellectual capital. We propose a model of innovation management to explain and evaluate the integration of those three areas applying a mixed methodology, theoretical foundations, and the analysis of the results. The overall results reveal that the certified software companies from Sinaloa manage innovation informally, through an internal, costly and independent innovation process without considering alliances with other companies, educational institutions, government agencies, technology parks or research and development centers.

Pragmatic Software Innovation

DEFF Research Database (Denmark)

Aaen, Ivan; Jensen, Rikke Hagensby

2014-01-01

We understand software innovation as concerned with introducing innovation into the development of software intensive systems, i.e. systems in which software development and/or integration are dominant considerations. Innovation is key in almost any strategy for competitiveness in existing markets......, for creating new markets, or for curbing rising public expenses, and software intensive systems are core elements in most such strategies. Software innovation therefore is vital for about every sector of the economy. Changes in software technologies over the last decades have opened up for experimentation......, learning, and flexibility in ongoing software projects, but how can this change be used to facilitate software innovation? How can a team systematically identify and pursue opportunities to create added value in ongoing projects? In this paper, we describe Deweyan pragmatism as the philosophical foundation...

Peak fitting and identification software library for high resolution gamma-ray spectra

International Nuclear Information System (INIS)

Uher, Josef; Roach, Greg; Tickner, James

2010-01-01

A new gamma-ray spectral analysis software package is under development in our laboratory. It can be operated as a stand-alone program or called as a software library from Java, C, C++ and MATLAB TM environments. It provides an advanced graphical user interface for data acquisition, spectral analysis and radioisotope identification. The code uses a peak-fitting function that includes peak asymmetry, Compton continuum and flexible background terms. Peak fitting function parameters can be calibrated as functions of energy. Each parameter can be constrained to improve fitting of overlapping peaks. All of these features can be adjusted by the user. To assist with peak identification, the code can automatically measure half-lives of single or multiple overlapping peaks from a time series of spectra. It implements library-based peak identification, with options for restricting the search based on radioisotope half-lives and reaction types. The software also improves the reliability of isotope identification by utilizing Monte-Carlo simulation results.

Software development methodology for computer based I&C systems of prototype fast breeder reactor

International Nuclear Information System (INIS)

Manimaran, M.; Shanmugam, A.; Parimalam, P.; Murali, N.; Satya Murty, S.A.V.

2015-01-01

Highlights: • Software development methodology adopted for computer based I&C systems of PFBR is detailed. • Constraints imposed as part of software requirements and coding phase are elaborated. • Compliance to safety and security requirements are described. • Usage of CASE (Computer Aided Software Engineering) tools during software design, analysis and testing phase are explained. - Abstract: Prototype Fast Breeder Reactor (PFBR) is sodium cooled reactor which is in the advanced stage of construction in Kalpakkam, India. Versa Module Europa bus based Real Time Computer (RTC) systems are deployed for Instrumentation & Control of PFBR. RTC systems have to perform safety functions within the stipulated time which calls for highly dependable software. Hence, well defined software development methodology is adopted for RTC systems starting from the requirement capture phase till the final validation of the software product. V-model is used for software development. IEC 60880 standard and AERB SG D-25 guideline are followed at each phase of software development. Requirements documents and design documents are prepared as per IEEE standards. Defensive programming strategies are followed for software development using C language. Verification and validation (V&V) of documents and software are carried out at each phase by independent V&V committee. Computer aided software engineering tools are used for software modelling, checking for MISRA C compliance and to carry out static and dynamic analysis. Various software metrics such as cyclomatic complexity, nesting depth and comment to code are checked. Test cases are generated using equivalence class partitioning, boundary value analysis and cause and effect graphing techniques. System integration testing is carried out wherein functional and performance requirements of the system are monitored

Software development methodology for computer based I&C systems of prototype fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Manimaran, M., E-mail: maran@igcar.gov.in; Shanmugam, A.; Parimalam, P.; Murali, N.; Satya Murty, S.A.V.

2015-10-15

Highlights: • Software development methodology adopted for computer based I&C systems of PFBR is detailed. • Constraints imposed as part of software requirements and coding phase are elaborated. • Compliance to safety and security requirements are described. • Usage of CASE (Computer Aided Software Engineering) tools during software design, analysis and testing phase are explained. - Abstract: Prototype Fast Breeder Reactor (PFBR) is sodium cooled reactor which is in the advanced stage of construction in Kalpakkam, India. Versa Module Europa bus based Real Time Computer (RTC) systems are deployed for Instrumentation & Control of PFBR. RTC systems have to perform safety functions within the stipulated time which calls for highly dependable software. Hence, well defined software development methodology is adopted for RTC systems starting from the requirement capture phase till the final validation of the software product. V-model is used for software development. IEC 60880 standard and AERB SG D-25 guideline are followed at each phase of software development. Requirements documents and design documents are prepared as per IEEE standards. Defensive programming strategies are followed for software development using C language. Verification and validation (V&V) of documents and software are carried out at each phase by independent V&V committee. Computer aided software engineering tools are used for software modelling, checking for MISRA C compliance and to carry out static and dynamic analysis. Various software metrics such as cyclomatic complexity, nesting depth and comment to code are checked. Test cases are generated using equivalence class partitioning, boundary value analysis and cause and effect graphing techniques. System integration testing is carried out wherein functional and performance requirements of the system are monitored.

Forecasting the Reference Evapotranspiration Using Time Series Model

Directory of Open Access Journals (Sweden)

H. Zare Abyaneh

2016-10-01

evapotranspiration were obtained. The mean values of evapotranspiration in the study period were 4.42, 3.93, 5.05, 5.49, and 5.60 mm day−1 in Esfahan, Semnan, Shiraz, Kerman, and Yazd, respectively. The Augmented Dickey-Fuller (ADF test was performed to the time series. The results showed that in all stations except Shiraz, time series had unit root and were non-stationary. The non-stationary time series became stationary at 1st difference. Using the EViews 7 software, the seasonal ARIMA models were applied to the evapotranspiration time series and R2 coefficient of determination, Durbin–Watson statistic (DW, Hannan-Quinn (HQ, Schwarz (SC and Akaike information criteria (AIC were used to determine, the best models for the stations were selected. The selected models were listed in Table 2. Moreover, information criteria (AIC, SC, and HQ were used to assess model parsimony. The independence assumption of the model residuals was confirmed by a sensitive diagnostic check. Furthermore, the homoscedasticity and normality assumptions were tested using other diagnostics tests. Table 2- The selected time series models for the stations Station\tSeasonal ARIMA model\tInformation criteria\tR2\tDW SC\tHQ\tAIC Esfahan\tARIMA(1, 1, 1×(1, 0, 112\t1.2571\t1.2840\t1.2396\t0.8800\t1.9987 Semnan\tARIMA(5, 1, 2×(1, 0, 112\t1.5665\t1.5122\t1.4770\t0.8543\t1.9911 Shiraz\tARIMA(2, 0, 3×(1, 0, 112\t1.3312\t1.2881\t1.2601\t0.9665\t1.9873 Kerman\tARIMA(5, 1, 1×(1, 0, 112\t1.8097\t1.7608\t1.8097\t0.8557\t2.0042 Yazd\tARIMA(2, 1, 3×(1, 1, 112\t1.7472\t1.7032\t1.6746\t0.5264\t1.9943 The seasonal ARIMA models presented in Table 2, were used at the 12 months (2004-2005 forecasting horizon. The results showed that the models produce good out-of-sample forecasts, which in all the stations the lowest correlation coefficient and the highest root mean square error were obtained 0.988 and 0.515 mm day−1, respectively. Conclusion: In the presented paper, reference evapotranspiration in the five synoptic

Software testability and its application to avionic software

Science.gov (United States)

Voas, Jeffrey M.; Miller, Keith W.; Payne, Jeffery E.

1993-01-01

Randomly generated black-box testing is an established yet controversial method of estimating software reliability. Unfortunately, as software applications have required higher reliabilities, practical difficulties with black-box testing have become increasingly problematic. These practical problems are particularly acute in life-critical avionics software, where requirements of 10 exp -7 failures per hour of system reliability can translate into a probability of failure (POF) of perhaps 10 exp -9 or less for each individual execution of the software. This paper describes the application of one type of testability analysis called 'sensitivity analysis' to B-737 avionics software; one application of sensitivity analysis is to quantify whether software testing is capable of detecting faults in a particular program and thus whether we can be confident that a tested program is not hiding faults. We so 80 by finding the testabilities of the individual statements of the program, and then use those statement testabilities to find the testabilities of the functions and modules. For the B-737 system we analyzed, we were able to isolate those functions that are more prone to hide errors during system/reliability testing.

The software life cycle

CERN Document Server

Ince, Darrel

1990-01-01

The Software Life Cycle deals with the software lifecycle, that is, what exactly happens when software is developed. Topics covered include aspects of software engineering, structured techniques of software development, and software project management. The use of mathematics to design and develop computer systems is also discussed. This book is comprised of 20 chapters divided into four sections and begins with an overview of software engineering and software development, paying particular attention to the birth of software engineering and the introduction of formal methods of software develop

Independent accident investigation: a modern safety tool

International Nuclear Information System (INIS)

Stoop, John A.

2004-01-01

Historically, safety has been subjected to a fragmented approach. In the past, every department has had its own responsibility towards safety, focusing either on working conditions, internal safety, external safety, rescue and emergency, public order or security. They each issued policy documents, which in their time were leading statements for elaboration and regulation. They also addressed safety issues with tools of various nature, often specifically developed within their domain. Due to a series of major accidents and disasters, the focus of attention is shifting from complying with quantitative risk standards towards intervention in primary operational processes, coping with systemic deficiencies and a more integrated assessment of safety in its societal context. In The Netherlands recognition of the importance of independent investigations has led to an expansion of this philosophy from the transport sector to other sectors. The philosophy now covers transport, industry, defense, natural disaster, environment and health and other major occurrences such as explosions, fires, and collapse of buildings or structures. In 2003 a multi-sector covering law will establish an independent safety board in The Netherlands. At a European level, mandatory investigation agencies are recognized as indispensable safety instruments for aviation, railways and the maritime sector, for which EU Directives are in place or being progressed [Transport accident and incident investigation in the European Union, European Transport Safety Council, ISBN 90-76024-10-3, Brussel, 2001]. Due to a series of major events, attention has been drawn to the consequences of disasters, highlighting the involvement of rescue and emergency services. They also have become subjected to investigative efforts, which in return, puts demands on investigation methodology. This paper comments on an evolutionary development in safety thinking and of safety boards, highlighting some consequences for strategic

Characterizability of metabolic pathway systems from time series data.

Science.gov (United States)

Voit, Eberhard O

2013-12-01

Over the past decade, the biomathematical community has devoted substantial effort to the complicated challenge of estimating parameter values for biological systems models. An even more difficult issue is the characterization of functional forms for the processes that govern these systems. Most parameter estimation approaches tacitly assume that these forms are known or can be assumed with some validity. However, this assumption is not always true. The recently proposed method of Dynamic Flux Estimation (DFE) addresses this problem in a genuinely novel fashion for metabolic pathway systems. Specifically, DFE allows the characterization of fluxes within such systems through an analysis of metabolic time series data. Its main drawback is the fact that DFE can only directly be applied if the pathway system contains as many metabolites as unknown fluxes. This situation is unfortunately rare. To overcome this roadblock, earlier work in this field had proposed strategies for augmenting the set of unknown fluxes with independent kinetic information, which however is not always available. Employing Moore-Penrose pseudo-inverse methods of linear algebra, the present article discusses an approach for characterizing fluxes from metabolic time series data that is applicable even if the pathway system is underdetermined and contains more fluxes than metabolites. Intriguingly, this approach is independent of a specific modeling framework and unaffected by noise in the experimental time series data. The results reveal whether any fluxes may be characterized and, if so, which subset is characterizable. They also help with the identification of fluxes that, if they could be determined independently, would allow the application of DFE. Copyright © 2013 Elsevier Inc. All rights reserved.

A 'Toolbox' Equivalent Process for Safety Analysis Software

International Nuclear Information System (INIS)

O'Kula, K.R.; Eng, Tony

2004-01-01

configuration and control procedure, an error notification and corrective action process, and evidence of available training on use of the software. The process is best performed with an independent SQA evaluator, i.e., a technically knowledgeable individual in the application area who is not part of the development team. The process provides a consistent, systematic approach based on the experience gained with SQA evaluations of the toolbox codes. Experience has shown that rarely will existing software be fully compliant with SQA criteria. Instead, the typical case is where SQA elements are deficient. For this case, it is recommended that supplemental remedial documentation be generated. Situations may also arise where the SQA evaluator must weigh whether the entire SQA suite be reconstituted. Regardless, the process is described sufficiently to guide a comprehensive evaluation. If the candidate software is successful in meeting process requirements, the software is ''toolbox-equivalent''. The benefit of the methodology outlined is that it provides a standard evaluation technique for choosing the most applicable software for a given application. One potential outcome is that the software of choice will be found to be applicable with ample SQA justification. Alternatively, the software in question may be found not to meet SQA process requirements. In this case, the analyst may then make an informed decision and possibly select one of the multiple-use, toolbox codes. With either outcome, the DSA is improved

Practical experience with software tools to assess and improve the quality of existing nuclear analysis and safety codes

International Nuclear Information System (INIS)

Marshall, N.H.; Marwil, E.S.; Matthews, S.D.; Stacey, B.J.

1990-01-01

Within the constraints of schedule and budget, software tools and techniques were applied to existing FORTRAN codes determining software quality metrics and improving the code quality. Specifically discussed are INEL experiences in applying pretty printers, cross-reference analyzers, and computer aided software engineering (CASE) tools and techniques. These have provided management with measures of the risk potential for individual program modules so that rational decisions can be made on resource allocation. Selected program modules have been modified to reduce the complexity, achieve higher functional independence, and improve the code vectorization. (orig.)

Calidad del software: camino hacia una verdadera industria del software

Directory of Open Access Journals (Sweden)

Saulo Ernesto Rojas Salamanca

1999-07-01

Full Text Available El software es quizá uno de los productos de la ingeniería que más ha evolucionado en muy poco tiempo, pasando desde el software empírico o artesanal hasta llegar al software desarrollado bajo los principios y herramientas de la ingeniería del software. Sin embargo, dentro de estos cambios, las personas encargadas de la elaboración del software se han enfrentado a problemas muy comunes: unos debido a la exigencia cada vez mayor en la capacidad de resultados del software, debido al permanente cambio de condiciones lo que aumenta su complejidad y obsolescencia; y otros, debido a la carencia de herramientas adecuadas y estándares de tipo organizacional encaminados al mejoramiento de los procesos en el desarrollo del software. Hacia la búsqueda de mecanismos de solución de estos últimos problemas se orienta este artículo...

Software Method for Computed Tomography Cylinder Data Unwrapping, Re-slicing, and Analysis

Science.gov (United States)

Roth, Don J.

2013-01-01

A software method has been developed that is applicable for analyzing cylindrical and partially cylindrical objects inspected using computed tomography (CT). This method involves unwrapping and re-slicing data so that the CT data from the cylindrical object can be viewed as a series of 2D sheets (or flattened onion skins ) in addition to a series of top view slices and 3D volume rendering. The advantages of viewing the data in this fashion are as follows: (1) the use of standard and specialized image processing and analysis methods is facilitated having 2D array data versus a volume rendering; (2) accurate lateral dimensional analysis of flaws is possible in the unwrapped sheets versus volume rendering; (3) flaws in the part jump out at the inspector with the proper contrast expansion settings in the unwrapped sheets; and (4) it is much easier for the inspector to locate flaws in the unwrapped sheets versus top view slices for very thin cylinders. The method is fully automated and requires no input from the user except proper voxel dimension from the CT experiment and wall thickness of the part. The software is available in 32-bit and 64-bit versions, and can be used with binary data (8- and 16-bit) and BMP type CT image sets. The software has memory (RAM) and hard-drive based modes. The advantage of the (64-bit) RAM-based mode is speed (and is very practical for users of 64-bit Windows operating systems and computers having 16 GB or more RAM). The advantage of the hard-drive based analysis is one can work with essentially unlimited-sized data sets. Separate windows are spawned for the unwrapped/re-sliced data view and any image processing interactive capability. Individual unwrapped images and un -wrapped image series can be saved in common image formats. More information is available at http://www.grc.nasa.gov/WWW/OptInstr/ NDE_CT_CylinderUnwrapper.html.

Software V and V of PPS for Shin-Hanul Nuclear Power Plant Units 1 and 2

International Nuclear Information System (INIS)

Park, Cheollak; Kang, Dongpa; Choe, Changhui; Sohn, Sedo; Beak, Seungmin

2013-01-01

Software V and V processes determine whether the development products of a given activity conform to the requirements of that activity and whether the software satisfies its intended use and user needs. This paper introduces the software V and V activities and tasks performed during the software development life cycle performed during the software development life cycle of the Plant Protection System (PPS) for Shin-Hanul Nuclear Power Plant Units 1 and 2 (SHN 1 and 2). The PPS generates signals to actuate Reactor Trip (RT) and Engineered Safety Features (ESF) whenever monitored processes exceed predetermined limits, and the PPS software is classified safety critical and an independent V and V is thus required according to regulations, code and standards. The software V and V efforts, sufficiently disciplined and rigorous, are quite essential to demonstrate that the software development process is of a high quality. The software V and V of PPS for SHN 1 and 2 has been accomplished successfully with systematic V and V procedures and methods established until test phase in compliance with related code and standards. In particular, the use of automated tools such as LDRA and DOORS greatly has contributed to an improvement of a software quality, and a reduction of a verification time and human errors

Complete modeling and software implementation of a virtual solar hydrogen hybrid system

International Nuclear Information System (INIS)

Pedrazzi, S.; Zini, G.; Tartarini, P.

2010-01-01

A complete mathematical model and software implementation of a solar hydrogen hybrid system has been developed and applied to real data. The mathematical model has been derived from sub-models taken from literature with appropriate modifications and improvements. The model has been implemented as a stand-alone virtual energy system in a model-based, multi-domain software environment. A test run has then been performed on typical residential user data-sets over a year-long period. Results show that the virtual hybrid system can bring about complete grid independence; in particular, hydrogen production balance is positive (+1.25 kg) after a year's operation with a system efficiency of 7%.

A New Effort for Atmospherical Forecast: Meteorological Image Processing Software (MIPS) for Astronomical Observations

Science.gov (United States)

Shameoni Niaei, M.; Kilic, Y.; Yildiran, B. E.; Yüzlükoglu, F.; Yesilyaprak, C.

2016-12-01

We have described a new software (MIPS) about the analysis and image processing of the meteorological satellite (Meteosat) data for an astronomical observatory. This software will be able to help to make some atmospherical forecast (cloud, humidity, rain) using meteosat data for robotic telescopes. MIPS uses a python library for Eumetsat data that aims to be completely open-source and licenced under GNU/General Public Licence (GPL). MIPS is a platform independent and uses h5py, numpy, and PIL with the general-purpose and high-level programming language Python and the QT framework.

A flexible and reusable software for real-time control applications at JET

International Nuclear Information System (INIS)

De Tommasi, G.; Piccolo, F.; Sartori, F.

2005-01-01

The fast growth of the JET real-time control network and the increasing demand for new systems have been the triggers that started the development of the JETRT software framework. This new architecture is designed for maximum reuse and is particularly suited for implementation of both real-time control and data acquisition systems in a complex experimental environment such as JET. Most of the software is the same in all applications independent of the platform. The varying part is the project specific algorithm, which is also compiled into a separate software component, in order to achieve a separation from the plant interface code. This design choice maximises the software reliability, reduces development costs and allows non-specialist programmers to contribute to the implementation of real-time projects. JETRT also provides an integrated set of debugging and testing tools, some of them well integrated with the Matlab environment. This feature besides the framework portability among different platforms allows to perform most of the test and validation phase on a desktop PC running Windows, significantly reducing the commissioning time of a new real-time system

Using software metrics and software reliability models to attain acceptable quality software for flight and ground support software for avionic systems

Science.gov (United States)

Lawrence, Stella

1992-01-01

This paper is concerned with methods of measuring and developing quality software. Reliable flight and ground support software is a highly important factor in the successful operation of the space shuttle program. Reliability is probably the most important of the characteristics inherent in the concept of 'software quality'. It is the probability of failure free operation of a computer program for a specified time and environment.

Comparison of Learning Software Architecture by Developing Social Applications versus Games on the Android Platform

Directory of Open Access Journals (Sweden)

Bian Wu

2012-01-01

Full Text Available This paper describes an empirical study where the focus was on discovering differences and similarities in students working on development of social applications versus students working on development of games using the same Android development platform. In 2010-2011, students attending the software architecture course at the Norwegian University of Science and Technology (NTNU could choose between four types of projects. Independently of the chosen type of project, all students had to go through the same phases, produce the same documents based on the same templates, and follow exactly the same process. This study focuses on one of projects—Android project, to see how much the application domain affects the course project independently of the chosen technology. Our results revealed some positive effects for the students doing game development compared to social application development to learn software architecture, like motivated to work with games, a better focus on quality attributes such as modifiability and testability during the development, production of software architectures of higher complexity, and more productive coding working for the project. However, we did not find significant differences in awarded grade between students choosing the two different domains.

Software Radar Technology

Directory of Open Access Journals (Sweden)

Tang Jun

2015-08-01

Full Text Available In this paper, the definition and the key features of Software Radar, which is a new concept, are proposed and discussed. We consider the development of modern radar system technology to be divided into three stages: Digital Radar, Software radar and Intelligent Radar, and the second stage is just commencing now. A Software Radar system should be a combination of various modern digital modular components conformed to certain software and hardware standards. Moreover, a software radar system with an open system architecture supporting to decouple application software and low level hardware would be easy to adopt "user requirements-oriented" developing methodology instead of traditional "specific function-oriented" developing methodology. Compared with traditional Digital Radar, Software Radar system can be easily reconfigured and scaled up or down to adapt to the changes of requirements and technologies. A demonstration Software Radar signal processing system, RadarLab 2.0, which has been developed by Tsinghua University, is introduced in this paper and the suggestions for the future development of Software Radar in China are also given in the conclusion.

Reliability Quantification Method for Safety Critical Software Based on a Finite Test Set

International Nuclear Information System (INIS)

Shin, Sung Min; Kim, Hee Eun; Kang, Hyun Gook; Lee, Seung Jun

2014-01-01

Software inside of digitalized system have very important role because it may cause irreversible consequence and affect the whole system as common cause failure. However, test-based reliability quantification method for some safety critical software has limitations caused by difficulties in developing input sets as a form of trajectory which is series of successive values of variables. To address these limitations, this study proposed another method which conduct the test using combination of single values of variables. To substitute the trajectory form of input using combination of variables, the possible range of each variable should be identified. For this purpose, assigned range of each variable, logical relations between variables, plant dynamics under certain situation, and characteristics of obtaining information of digital device are considered. A feasibility of the proposed method was confirmed through an application to the Reactor Protection System (RPS) software trip logic

Application of Metric-based Software Reliability Analysis to Example Software