WorldWideScience

Sample records for separation technical progress

  1. Fundamental studies of separation processes. Technical progress report

    Rogers, L.B.

    1975-06-01

    Studies using high-precision gas chromatography and supercritical fluid chromatography have produced new types of information on liquid crystals and on behavior of substances in the region of the critical temperature, respectively. In addition, the first successful studies of the effects of pressure on cation exchange have been made using aqueous solutions of alkali metal nitrates. In contrast, progress on separations of isotopic species using gas chromatography has been disappointing. In that area, the chief accomplishment has been a determination of the levels of accuracy and precision with which isotopic abundances can be measured using our quadrupole mass spectrometer. (U.S.)

  2. Technical progress report

    1982-01-01

    This report summarizes the work carried out by personnel at the Nuclear Physics Laboratory of the University of Colorado from about August 1, 1981 to October 1, 1982, under contract with the Department of Energy. The intermediate energy studies summarized in this report were carried out at the meson physics facilities at Los Alamos (LAMPF), the cyclotron at Indiana University (IUCF), and the meson physics facilities at Vancouver (TRIUMF). This year, for the first time, intermediate energy experimental studies are being reported in separate documents from the low energy and theoretical nuclear physics efforts. Experimental studies are reported on pion-nucleus interactions, charge exchange reactions, nucleon transfer reactions, and apparatus development

  3. Technical progress report

    1996-01-01

    This report summarizes experimental and theoretical work in basic nuclear physics carried out between October 1, 1995, the closing of our last Progress Report, and September 30, 1996 at the Nuclear Physics Laboratory of the University of Colorado, Boulder, under contracts DE-FG03-93ER-40774 and DE-FG03-95ER-40913 with the United States Department of Energy. The experimental contract supports broadly-based experimental research in intermediate energy nuclear physics. This report includes results from studies of Elementary Systems involving the study of the structure of the nucleon via polarized high-energy positron scattering (the HERMES experiment) and lower energy pion scattering from both polarized and unpolarized nucleon targets. Results from pion- and kaon-induced reactions in a variety of nuclear systems are reported under the section heading Meson Reactions; the impact of these and other results on understanding the nucleus is presented in the Nuclear Structure section. In addition, new results from scattering of high-energy electrons (from CEBAF/TJNAF) and pions (from KEK) from a broad range of nuclei are reported in the section on Incoherent Reactions. Finally, the development and performance of detectors produced by the laboratory are described in the section titled Instrumentation

  4. Works Technical Department progress report, March 1961

    None

    1961-04-19

    This document details the activities of the Savannah River Works Technical Department during the month of March 1961. Topics discussed are: Reactor Technology, Separations Technology, Engineering Assistance, Health Physics, Laboratories Overview, and Technical Papers Issued.

  5. Technical progress and climatic change

    Ausubel, J.H.

    1995-01-01

    The global warming debate has neglected and thus underestimated the importance of technical change in considering reduction in greenhouse gases and adaptation to climate change. Relevant quantitative cases of long-run technical change during the past 100 years are presented in computing, communications, transport, energy, and agriculture. A noteworthy technological trajectory is that of decarbonization, or decreasing carbon intensity of primary energy. If human societies have not yet reached the end of the history of technology, the cost structure for mitigation and adaptation changes could be cheap. (Author)

  6. Progress report : Technical Physics Division

    Gopalaraman, C.P.; Deshpande, R.Y.

    1978-01-01

    The research and development work carried out in the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, is reported. Some of the achievements are: (1) fabrication of mass spectrometers for heavy water analysis and lithium 6/7 isotope ratio measurement, (2) fabrication of electronic components for mass spectrometers, (3) growing of sodium iodide crystals for radiation detectors, (4) development of sandwich detectors comprising of NaI(Tl) and CaI(Na), (5) fabrication of mass spectrometer type leak detectors and (6) fabrication of the high vacuum components of the vacuum system of the variable energy cyclotron based at Calcutta. (M.G.B.)

  7. Sludge Treatment Evaluation: 1992 Technical progress

    Silva, L.J.; Felmy, A.R.; Ding, E.R.

    1993-01-01

    This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO 3 , NO 2 , PO 4 , SO 4 , and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model

  8. Sludge Treatment Evaluation: 1992 Technical progress

    Silva, L J; Felmy, A R; Ding, E R

    1993-01-01

    This report documents Fiscal Year 1992 technical progress on the Sludge Treatment Evaluation Task, which is being conducted by Pacific Northwest Laboratory. The objective of this task is to develop a capability to predict the performance of pretreatment processes for mixed radioactive and hazardous waste stored at Hanford and other US Department of Energy (DOE) sites. Significant cost savings can be achieved if radionuclides and other undesirable constituents can be effectively separated from the bulk waste prior to final treatment and disposal. This work is initially focused on chemical equilibrium prediction of water washing and acid or base dissolution of Hanford single-shell tank (SST) sludges, but may also be applied to other steps in pretreatment processes or to other wastes. Although SST wastes contain many chemical species, there are relatively few constituents -- Na, Al, NO[sub 3], NO[sub 2], PO[sub 4], SO[sub 4], and F -- contained in the majority of the waste. These constituents comprise 86% and 74% of samples from B-110 and U-110 SSTS, respectively. The major radionuclides of interest (Cs, Sr, Tc, U) are present in the sludge in small molal quantities. For these constituents, and other important components that are present in small molal quantities, the specific ion-interaction terms used in the Pitzer or NRTL equations may be assumed to be zero for a first approximation. Model development can also be accelerated by considering only the acid or base conditions that apply for the key pretreatment steps. This significantly reduces the number of chemical species and chemical reactions that need to be considered. Therefore, significant progress can be made by developing all the specific ion interactions for a base model and an acid dissolution model.

  9. 48 CFR 2052.211-71 - Technical progress report.

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Technical progress report... Technical progress report. As prescribed at 2011.104-70(b), the contracting officer shall insert the... solicitation. Technical Progress Report (JAN 1993) The contractor shall provide a monthly Technical Progress...

  10. Technical progress and its strategic consequences

    Bouchard, G.

    1999-01-01

    The history of energy during recent decades has shown that technical progress can have consequences for the organisation of markets, company strategies and the economy in general, confounding all forecasts and going beyond simple technical change. As a consequence for example, improvements in the techniques concerning the exploration and production of hydrocarbons have led to the petrol 'counter-crisis', the reduction in the power of OPEC and undreamed of gains in wealth for certain countries. The progress in gas turbines has led to the reversal of the age-old tendency towards increases in the size of electricity production units and encouraged the liberation of this sector. When looking at the future it is therefore judicious to try and understand the forces at work, and the major trends which result. This is the aim of the articles in this edition of the Revue de l'Energie, published on the occasion of the European colloquium on 'Technical progress faced with the challenges of the energy sector in the future' organised by the Association of Energy Economists. (authors)

  11. International linear collider. A technical progress report

    Arnold, Ned [Argonne National Laboratory, IL (United States); Aderhold, Sebastian [DESY, Hamburg (Germany); Adolphsen, Chris [Stanford Linear Accelerator Center, Menlo Park, CA (United States); and others

    2012-07-01

    The International Linear Collider: A Technical Progress Report marks the halfway point towards the Global Design Effort fulfilling its mandate to follow up the ILC Reference Design Report with a more optimised Technical Design Report (TDR) by the end of 2012. The TDR will be based on much of the work reported here and will contain all the elements needed to propose the ILC to collaborating governments, including a technical design and implementation plan that are realistic and have been better optimised for performance, cost and risk. We are on track to develop detailed plans for the ILC, such that once results from the Large Hadron Collider (LHC) at CERN establish the main science goals and parameters of the next machine, we will be in good position to make a strong proposal for this new major global project in particle physics. The two overriding issues for the ILC R and D programme are to demonstrate that the technical requirements for the accelerator are achievable with practical technologies, and that the ambitious physics goals can be addressed by realistic ILC detectors. This GDE interim report documents the impressive progress on the accelerator technologies that can make the ILC a reality. It highlights results of the technological demonstrations that are giving the community increased confidence that we will be ready to proceed with an ILC project following the TDR. The companion detector and physics report document likewise demonstrates how detector designs can meet the ambitious and detailed physics goals set out by the ILC Steering Committee. LHC results will likely affect the requirements for the machine design and the detectors, and we are monitoring that very closely, intending to adapt our design as those results become available.

  12. Technical feasibility of advanced separation; Faisabilite technique de la separation poussee

    Rostaing, Ch

    2004-07-01

    Advanced separation aims at reducing the amount and toxicity of high-level and long lived radioactive wastes. The Purex process has been retained as a reference way for the recovery of the most radio-toxic elements: neptunium, technetium and iodine. Complementary solvent extraction processes have to be developed for the separation of americium, curium and cesium from the high activity effluent of the spent fuel reprocessing treatment. Researches have been carried out with the aim of demonstrating the scientifical and technical feasibility of advanced separation of minor actinides and long lived fission products from spent fuels. The scientifical feasibility was demonstrated at the end of 2001. The technical feasibility works started in the beginning of 2002. Many results have been obtained which are presented and summarized in this document: approach followed, processes retained for the technical feasibility (An/Ln and Am/Cm separation), processes retained for further validation at the new shielded Purex installation, technical feasibility of Purex adaptation to Np separation, technical feasibility of Diamex (first step: (An+Ln)/other fission products) separation), technical feasibility of Sanex process (second step: An(III)/Ln(III) separation), technical feasibility of Am(III)/Cm(III) separation, cesium separation, iodine separation, technical-economical evaluation, conclusions and perspectives, facilities and apparatuses used for the experiments. (J.S.)

  13. Nonequilibrium photochemical reactions induced by lasers. Technical progress report

    Steinfeld, J.I.

    1978-04-01

    Research has progressed in six principal subject areas of interest to DOE advanced (laser) isotope separation efforts. These are (1) Infrared double resonance spectroscopy of molecules excited by multiple infrared photon absorption, particularly SF 6 and vinyl chloride. (2) Infrared multiphoton excitation of metastable triplet-state molecules, e.g., biacetyl. (3) An Information Theory analysis of multiphoton excitation and collisional deactivation has been carried out. (4) The mechanism of infrared energy deposition and multiphoton-induced reactions in chlorinated ethylene derivatives; and RRKM (statistical) model accounts for all observed behavior of the system, and a deuterium-specific reaction pathway has been identified. (5) Diffusion-enhanced laser isotope separation in N 16 O/N 18 O. (6) A technical evaluation of laser-induced chemistry and isotope separation

  14. Environmental Research Division technical progress report, January 1984-December 1985

    1986-05-01

    Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter

  15. Environmental Research Division technical progress report, January 1984-December 1985

    1986-05-01

    Technical progress in the various research and assessment activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1984 to 1985. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Environmental Impacts, Fundamental Molecular Physics and Chemistry, and Waste Management Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter.

  16. Technical progress safeguards future. Technischer Fortschritt sichert die Zukunft

    1985-01-01

    'Technical progress safeguards future', the guiding theme of the 1985 conference of German engineers, calls for discussion. In five lectures representatives of the subdivisions of 'VDI' issued their statements from the viewpoints of their special fields. These lectures were completed by reports on the part of the remaining VDI subdivisions, which are published together with the lectures in this volume. The complex guiding theme is meant to stimulate discussion, which should be conducted also with representatives of other sciences and the public. The volume contains a.o. contributions regarding future prospects, given certain modifications in construction engineering and user behaviour in the sector heating and air-conditioning, regarding the development of new construction techniques to protect the environment, and regarding clean air as an international concern of engineers. For these three contributions separate entries were made. Other presentations relate to: automobile production technology; energy supply as an engineering task; information, invention, innovation as stages of technical progress; progress in materials technology; noise of motor vehicles - current state and future prospects. (orig./HSCH).

  17. Technical progress by major task. Semiannual technical progress report, September 29, 1997 - March 29, 1998

    1998-01-01

    The technical progress achieved during the period 29 September 1997 through 29 March 1998 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described in this report. The report is organized by program task structure: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; RTG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair

  18. Recent progress in fission product separation

    Raggenbass, A.

    1964-01-01

    Successful experiments have been done on the method described at Geneva in 1958. The process has been considerably improved: 1 - Initially, the caesium phospho tungstate precipitate was leached barium hydroxide in the centrifuge and this was followed by a distillation of ammonia in a concentrator. The barium hydroxide was then eliminated by carbonate precipitation and centrifugation. It has been proved that the ammonia distillation could be replaced by its evaporation during centrifugation, thus eliminating the need of a concentrator. It was then possible to carry out the carbonation on the solide-liquid mixture produced by the baryte water leaching. 2 - In applying the above process to the treatment of solutions derived from uranium molybdenum fuels, concentrating is to be recommended in order to hold the molybdenum in solution by complexing it with phosphoric acid. This complexing process provides a suspension of zirconium phosphate and ammonium phospho tungstate. These are separated by passing into a basic medium which precipitates the zirconium oxide, then turning back to an acid medium; the end of the treatment remains unchanged. 3 - Studies carried out in several countries on the exchange properties of hetero-polyacid salts have always met with difficulties as a result of the poor mechanical properties of these substances. This difficulty has been overcome by wrapping the ammonium phospho tungstate in a zirconium phosphate matrix. The exchanger obtained possesses: satisfactory mechanical properties, - a capacity of 0.1 milli equivalent per gram in concentrated nitric acid solution. It can be eluted and regenerated by a solution of an ammonium salt. The procedure for recovery of these various fission products is briefly the following: extraction of rare earths by di-2-ethyl hexyl phosphoric acid into dodecane at pH 2, the chemical impurities being complexed by citric acid, extraction of most of the magnesium at pH 4 by the same solvents the solvent being

  19. Solar lease grant program. Technical progress report

    1981-04-01

    Progress on a lease program for the installation of a solar water heater with no installation charge is reported. Information on the announcement of the program, the selection of participants, the contractural agreement, progress on installation of equipment, monitoring, and evaluation is summarized. The status of the budget concerned with the program is announced. Forms used for applications for the program and an announcement from Resource Alternatives for Cilco customers are presented.

  20. Progress in metal ion separation and preconcentration : an overview.

    Bond, A. H.

    1998-05-19

    A brief historical perspective covering the most mature chemically-based metal ion separation methods is presented, as is a summary of the recommendations made in the 1987 National Research Council (NRC) report entitled ''Separation and Purification: Critical Needs and Opportunities''. A review of Progress in Metal Ion Separation and Preconcentration shows that advances are occurring in each area of need cited by the NRC. Following an explanation of the objectives and general organization of this book, the contents of each chapter are briefly summarized and some future research opportunities in metal ion separations are presented.

  1. Progress in metal ion separation and preconcentration: an overview

    Bond, A. H.

    1998-01-01

    A brief historical perspective covering the most mature chemically-based metal ion separation methods is presented, as is a summary of the recommendations made in the 1987 National Research Council (NRC) report entitled ''Separation and Purification: Critical Needs and Opportunities''. A review of Progress in Metal Ion Separation and Preconcentration shows that advances are occurring in each area of need cited by the NRC. Following an explanation of the objectives and general organization of this book, the contents of each chapter are briefly summarized and some future research opportunities in metal ion separations are presented

  2. Nuclear theory research. Technical progress report

    1982-01-01

    Progress is briefly described on the following studies: (1) Dirac phenomenology for deuteron elastic scattering, (2) Dirac wave functions in nuclear distorted wave calculations, (3) impulse approximation for p→p → dπ + reaction above the 3-3 resonance, (4) coherent π production, (5) nuclear potentials from Dirac bound state wavefunctions, (6) nonlocality effects in nuclear reactions, (7) unhappiness factors in DWBA description of (t,p) and (p,t) reactions, (8) absolute normalization of three-nucleon transfer reactions, (9) formulation of a finite-range CCBA computer program, (10) crossing symmetric solutions of the low equations, (11) pion scattering from quark bags, (12) study of the p 11 channel in the delta model, (13) isovector corrections in pion-nucleus scattering, (14) pionic excitation of nuclear giant resonances, and (15) isospin dependence of the second-order pion-nucleus optical potential

  3. Progress report [of] Technical Physics Division

    Vijendran, P.; Deshpande, R.Y.

    1975-01-01

    Activities of the Technical Physics Division of the Bhabha Atomic Research Centre, Bombay, over the last few years are reported. This division is engaged in developing various technologies supporting the development of nuclear technology. The various fields in which development is actively being carried out are : (i) vacuum technology, (ii) mass spectrometry, (iii) crystal technology, (iv) cryogenics, and (v) magnet technology. For surface studies, the field emission microscope and the Auger electron spectrometer and other types of spectrometers have been devised and perfected. Electromagnets of requisite strength to be used in MHD programme and NMR instruments are being fabricated. Various crystals such as NaI(Tl), Ge, Fluorides, etc. required as windows and prisms in X and gamma-ray spectroscopy, have been grown. In the cryogenics field, expansion engines required for air liquefaction plants, vacuum insulated dewars, helium gas thermometers etc. have been constructed. In addition to the above, the Division provides consultancy and training to personnel from various institutions and laboratories. Equipment and systems perfected are transferred to commercial organizations for regular production. (A.K.)

  4. Swallowable Wireless Capsule Endoscopy: Progress and Technical Challenges

    Guobing Pan

    2012-01-01

    Full Text Available Wireless capsule endoscopy (WCE offers a feasible noninvasive way to detect the whole gastrointestinal (GI tract and revolutionizes the diagnosis technology. However, compared with wired endoscopies, the limited working time, the low frame rate, and the low image resolution limit the wider application. The progress of this new technology is reviewed in this paper, and the evolution tendencies are analyzed to be high image resolution, high frame rate, and long working time. Unfortunately, the power supply of capsule endoscope (CE is the bottleneck. Wireless power transmission (WPT is the promising solution to this problem, but is also the technical challenge. Active CE is another tendency and will be the next geneion of the WCE. Nevertheless, it will not come true shortly, unless the practical locomotion mechanism of the active CE in GI tract is achieved. The locomotion mechanism is the other technical challenge, besides the challenge of WPT. The progress about the WPT and the active capsule technology is reviewed.

  5. Environmental Research Division technical progress report: January 1986--October 1987

    1988-07-01

    Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases

  6. Environmental Research Division technical progress report: January 1986--October 1987

    1988-07-01

    Technical process in the various research activities of Argonne National Laboratory's Environmental Research Division is reported for the period 1986-1987. Textual, graphic, and tabular information is used to briefly summarize (in separate chapters) the work of the Division's Atmospheric Physics, Environmental Effects Research, Fundamental Molecular Physics and Chemistry, and Organic Geochemistry and Environmental Instrumentation Programs. Information on professional qualifications, awards, and outstanding professional activities of staff members, as well as lists of publications, oral presentations, special events organized, and participants in educational programs, are provided in appendices at the end of each chapter. Individual projects under each division are processed separately for the data bases.

  7. Technical Progress of the New Worlds Observer Mission

    Lo, Amy; Noecker, C.; Cash, W.; NWO Study Team

    2009-01-01

    We report on the technical progress of the New Worlds Observer (NWO) mission concept. NWO is a two spacecraft mission that is capable of detecting and characterizing extra-solar, terrestrial planets and planetary systems. NWO consists of an external starshade and an UV-optical space telescope, flying in tandem. The starshade is a petal-shaped, opaque screen that creates an extremely dark shadow large enough to shade the telescope aperture from the target star. The NWO team has been addressing the top technology challenges of the concept, and report here our progress. We will present the current mission configuration best suited to address Terrestrial Planet Finding requirements, and highlight the technological breakthroughs that we have achieved this year. In particular, we will report on progress made in precision deployables for the large starshade, and the trajectory & alignment control system for NWO. We will also briefly highlight advances in understanding the starshade optical performance.

  8. Stockholm international conference 2003 on geological repositories: Political and technical progress

    2004-01-01

    The conference reviewed global progress made as well as current perspectives on the activities to develop geologic repositories. The objectives were to review the progress in policy making as well as technical issues and to strengthen international co-operation on waste management and disposal issues. The first day of the conference addressed the policy aspects of geological repositories and the second day featured the more technical issues. Session 1: International progress in performing long-term safety studies and security of geological disposal were discussed and reviewed with examples from OECD/NEA, Belgium, Sweden, USA, Switzerland and Russia. Session 2: Views on stakeholder involvement and decision making process were presented by international organisations and national implementers from Japan, United Kingdom, Belgium and OECD/NEA. Session 3: Views on stakeholder involvement and decision making process were presented by regional and local stakeholders from France, Finland, Korea and Sweden. Session 4: International instruments assisting in the implementation of geological repositories were discussed, for example ICRP and IAEA/NEA safety documents, Joint Convention, Safeguard agreements, Nuclear Liability Conventions, etc. Session 5: The contribution of Research, Development and Demonstration was discussed with overviews of the progress achieved on scientific and technical issues over the past four years. Progress and key issues were presented from Switzerland, USA, Finland, Japan, Sweden and IAEA. Each of the papers and poster presentations have been analysed and indexed separately

  9. International Linear Collider-A Technical Progress Report

    Elsen, Eckhard; /DESY; Harrison, Mike; /Brookhaven; Hesla, Leah; /Fermilab; Ross, Marc; /Fermilab; Royole-Degieux, Perrine; /Paris, IN2P3; Takahashi, Rika; /KEK, Tsukuba; Walker, Nicholas; /DESY; Warmbein, Barbara; /DESY; Yamamoto, Akira; /KEK, Tsukuba; Yokoya, Kaoru; /KEK, Tsukuba; Zhang, Min; /Beijing, Inst. High Energy Phys.

    2011-11-04

    The International Linear Collider: A Technical Progress Report marks the halfway point towards the Global Design Effort fulfilling its mandate to follow up the ILC Reference Design Report with a more optimised Technical Design Report (TDR) by the end of 2012. The TDR will be based on much of the work reported here and will contain all the elements needed to propose the ILC to collaborating governments, including a technical design and implementation plan that are realistic and have been better optimised for performance, cost and risk. We are on track to develop detailed plans for the ILC, such that once results from the Large Hadron Collider (LHC) at CERN establish the main science goals and parameters of the next machine, we will be in good position to make a strong proposal for this new major global project in particle physics. The two overriding issues for the ILC R&D programme are to demonstrate that the technical requirements for the accelerator are achievable with practical technologies, and that the ambitious physics goals can be addressed by realistic ILC detectors. This GDE interim report documents the impressive progress on the accelerator technologies that can make the ILC a reality. It highlights results of the technological demonstrations that are giving the community increased confidence that we will be ready to proceed with an ILC project following the TDR. The companion detector and physics report document likewise demonstrates how detector designs can meet the ambitious and detailed physics goals set out by the ILC Steering Committee. LHC results will likely affect the requirements for the machine design and the detectors, and we are monitoring that very closely, intending to adapt our design as those results become available.

  10. Technical progress report, 1 April-30 June 1981

    None

    1981-01-01

    This report describes the technical accomplishments during the quarter ending June 1981, on the commercial nuclear waste management programs under the direction of the Office of Nuclear Waste Isolation (ONWI). The ONWI program is organized into 8 tasks entitled: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. Principal investigators in each of these areas have submitted summaries of quarterly highlights for inclusion in this report. Separate abstracts have been prepared for 5 of these tasks for inclusion in the Energy Data Base. (DMC)

  11. Separation of organic azeotropic mixtures by pervaporation. Final technical report

    Baker, R.W.

    1991-12-01

    Distillation is a commonly used separation technique in the petroleum refining and chemical processing industries. However, there are a number of potential separations involving azetropic and close-boiling organic mixtures that cannot be separated efficiently by distillation. Pervaporation is a membrane-based process that uses selective permeation through membranes to separate liquid mixtures. Because the separation process is not affected by the relative volatility of the mixture components being separated, pervaporation can be used to separate azetropes and close-boiling mixtures. Our results showed that pervaporation membranes can be used to separate azeotropic mixtures efficiently, a result that is not achievable with simple distillation. The membranes were 5--10 times more permeable to one of the components of the mixture, concentrating it in the permeate stream. For example, the membrane was 10 times more permeable to ethanol than methyl ethyl ketone, producing 60% ethanol permeate from an azeotropic mixture of ethanol and methyl ethyl ketone containing 18% ethanol. For the ethyl acetate/water mixture, the membranes showed a very high selectivity to water (> 300) and the permeate was 50--100 times enriched in water relative to the feed. The membranes had permeate fluxes on the order of 0.1--1 kg/m{sup 2}{center_dot}h in the operating range of 55--70{degrees}C. Higher fluxes were obtained by increasing the operating temperature.

  12. Isotope separation by chemical exchange process: Final technical report

    Schneider, A.

    1987-02-01

    The feasibility of a chemical exchange method for the separation of the isotopes of europium was demonstrated in the system EuCl 2 -EuCl 3 . The single stage separation factor, α, in this system is 1.001 or 1.0005 per mass unit. This value of α is comparable to the separation factors reported for the U 4+ - U 6 and U 3+ - Y 4+ systems. The separation of the ionic species was done by precipitation of the Eu 2+ ions or by extraction of the Eu 3+ ions with HDEHP. Conceptual schemes were developed for a countercurrent reflux cascades consisting of solvent extraction contractors. A regenerative electrocel, combining simultaneous europium reduction, europium oxidation with energy generation, and europium stripping from the organic phase is described. 32 refs., 22 figs., 6 tabs

  13. Savannah River Plant, Works Technical Department monthly progress report for March 1956

    1956-01-01

    This document details activities of the Works Technical Department during the month of March 1956. It covers reactor technology, separations technology, engineering assistance and heavy water technology

  14. FY 1992 work plan and technical progress reports

    NONE

    1992-11-01

    The Desert Research Institute (DRI) is a division of the University of Nevada System devoted to multidisciplinary scientific research. For more than 25 years, DRI has conducted research for the US Department of Energy`s Nevada Field Office (DOE/NV) in support of operations at the Nevada Test Site (NTS). During that time, the research program has grown from an early focus on hydrologic studies to include the areas of geology, archaeology, environmental compliance and monitoring, statistics, database management, public education, and community relations. The range of DRI`s activities has also expanded to include a considerable amount of management and administrative support in addition to scientific investigations. DRI`s work plan for FY 1992 reflects a changing emphasis in DOE/NV activities from nuclear weapons testing to environmental restoration and monitoring. Most of the environmental projects from FY 1991 are continuing, and several new projects have been added to the Environmental Compliance Program. The Office of Technology Development Program, created during FY 1991, also includes a number of environmental projects. This document contains the FY 1992 work plan and quarterly technical progress reports for each DRI project.

  15. Recent progress in the chemical separations for the Actinex project

    Musikas, C.; Bourges, J.; Madic, C.; Cuillerdier, C.; Adnet, J.M.

    1991-01-01

    Conceptual flow-sheets and laboratory works have been carried out recently in Fontenay-aux-Roses to gain insight into the partitioning of the actinides contained in various wastes, including the HLLW. The flow-sheets designed to separate the HLLW actinides include two main steps: the first is the removal of the actinide (VI), (IV), (III) from the acidic effluent of the first PUREX process extraction cycle; the second is the separation of the trivalent lanthanides from the trivalent actinides which were co-extracted with the actinides in the first step. N,N'-tetraalkylpropanediamide will be used in the first step. The properties and the advantages-disadvantages of these extractants will be discussed. For the trivalent actinide-lanthanide group separation two ways are explored simultaneously. The first one is a research of new extractants for the group separation of the 4f-5f trivalent ions. Several extraction systems are candidates for this separation; the actinides having an higher affinity for the ligands bearing donor atoms softer than oxygen. The point of the subject will be given. The second way is the separation of Am from the trivalent lanthanides after Am(IV) is protected by unsaturated phosphotungstates and can be extracted as phosphotungstate by primary or secondary amine. The work which must be achieved to apply this flow-sheet to the HLLW partitioning at the industrial scale is pointed out

  16. RECENT PROGRESS OF OXYGEN/NITROGEN SEPARATION USING MEMBRANE TECHNOLOGY

    K. C. CHONG

    2016-07-01

    Full Text Available The oxygen-enriched air is highly demanded for various industrial applications such as medical, chemical and enhanced combustion processes. The conventional oxygen/nitrogen production is either cryogenic distillation or pressure swing adsorption (PSA. Both of these techniques possess the production capability of 20 to 300 tonnes of oxygen per day and oxygen purity of more than 95%. However, these techniques are energy intensive. Alternatively, membrane technology is an emerging technology in gas separation as it requires low energy consumption and relatively moderate production volume, if compared to the conventional gas production techniques. These advantages have spurred much interest from industries and academics to speed up the commercial viability of the O2/N2 separation via membrane technology. In this review, the conventional and membrane technologies in O2/N2 separation, as well as recent development of membrane fabrication techniques and materials are reviewed. The latest membrane performance in O2/N2 separation is also tabulated and discussed.

  17. Current progress and technical challenges of flexible liquid crystal displays

    Fujikake, Hideo; Sato, Hiroto

    2009-02-01

    We focused on several technical approaches to flexible liquid crystal (LC) display in this report. We have been developing flexible displays using plastic film substrates based on polymer-dispersed LC technology with molecular alignment control. In our representative devices, molecular-aligned polymer walls keep plastic-substrate gap constant without LC alignment disorder, and aligned polymer networks create monostable switching of fast-response ferroelectric LC (FLC) for grayscale capability. In the fabrication process, a high-viscosity FLC/monomer solution was printed, sandwiched and pressed between plastic substrates. Then the polymer walls and networks were sequentially formed based on photo-polymerization-induced phase separation in the nematic phase by two exposure processes of patterned and uniform ultraviolet light. The two flexible backlight films of direct illumination and light-guide methods using small three-primary-color light-emitting diodes were fabricated to obtain high-visibility display images. The fabricated flexible FLC panels were driven by external transistor arrays, internal organic thin film transistor (TFT) arrays, and poly-Si TFT arrays. We achieved full-color moving-image displays using the flexible FLC panel and the flexible backlight film based on field-sequential-color driving technique. Otherwise, for backlight-free flexible LC displays, flexible reflective devices of twisted guest-host nematic LC and cholesteric LC were discussed with molecular-aligned polymer walls. Singlesubstrate device structure and fabrication method using self-standing polymer-stabilized nematic LC film and polymer ceiling layer were also proposed for obtaining LC devices with excellent flexibility.

  18. Efficient separations and processing crosscutting program 1996 technical exchange meeting. Proceedings

    1996-01-01

    This document contains summaries of technology development presented at the 1996 Efficient Separations and Processing Crosscutting Program Technical Exchange Meeting. This meeting is held annually to promote a free exchange of ideas among technology developers, potential users and other interested parties within the EM community. During this meeting the following many separation processes technologies were discussed such as ion exchange, membrane separation, vacuum distillation, selective sorption, and solvent extraction. Other topics discussed include: waste forms; testing or inorganic sorbents for radionuclide and heavy metal removal; selective crystallization; and electrochemical treatment of liquid wastes. This is the leading abstract, individual papers have been indexed separately for the databases

  19. Efficient separations and processing crosscutting program 1996 technical exchange meeting. Proceedings

    NONE

    1996-02-01

    This document contains summaries of technology development presented at the 1996 Efficient Separations and Processing Crosscutting Program Technical Exchange Meeting. This meeting is held annually to promote a free exchange of ideas among technology developers, potential users and other interested parties within the EM community. During this meeting the following many separation processes technologies were discussed such as ion exchange, membrane separation, vacuum distillation, selective sorption, and solvent extraction. Other topics discussed include: waste forms; testing or inorganic sorbents for radionuclide and heavy metal removal; selective crystallization; and electrochemical treatment of liquid wastes. This is the leading abstract, individual papers have been indexed separately for the databases.

  20. Technical progress in planning organization of the Ostravo-Karwina coal basin, ''Mining Projects of Ostravo''

    Karpeta, B; Kolar, J

    1979-01-01

    Based on the main task of further improvement in labor productivity and improvement in the quality of products, the leading planning organization of the Ostravo-Karwina basin is planning and realizing progressive technological plans based on new equipment. Long-term plans for basin development up to 1990 stipulate a rise in capital investments by 180%, increase in the volume of productivity by 164% with a rise in the number of workers by 142%. Corresponding technical progress in planning is based on an improvement in the system of scientific-technical information, automation and technical equipping of the planning process, improvements in the forms and organizational structure. Organization of specialized research-planning groups to substantiate and to technically-economically evaluate technical progress, and also to develop comprehensive technical assignments is stipulated.

  1. Savannah River Plant Works Technical Department monthly progress report for May 1958: Deleted Version

    1958-06-17

    This progress report by the Atomic Energy Division of the Savannah River Plant covers: Reactor Technology; Separation Technology; Engineering Assistance; Health Physics; and General Laboratory Work. (JT)

  2. Proceedings of the efficient separations and processing crosscutting program 1997 technical exchange meeting

    Gephart, J.M. [ed.

    1997-05-01

    This document contains summaries of technology development presented at the 1997 Efficient Separations and Processing Crosscutting Program (ESP-CP) Technical Exchange Meeting (TEM), held January 28-30, 1997, in Gaithersburg, Maryland. The ESP-CP is sponsored by the U.S. Department of Energy`s Office of Environmental Management (DOE/EM), Office of Science and Technology. The ESP-CP TEM is held annually to: (1) Present current technology development activities funded by the ESP-CP. Developers of ESP-CP-funded technologies describe the problems and needs addressed by their technologies; the technical approach, accomplishments, and resolution of issues; the strategy and schedule for commercialization; and evolving potential applications. Representatives from DOE/EM`s Focus Areas also present their technology needs. (2) Promote the exchange of technical information among those developing new separations technologies, those responsible for providing new separations technologies to meet DOE/EM needs, and those who need or will potentially make use of such technologies. (3) Familiarize the ESP-CP Technical Review Team with the FY 1997 program and solicit reviewers` views on the program as a whole. This meeting is not a program review of the individual tasks, but instead focuses on the technical aspects and implementation of ESP-CP-sponsored technology or data. This document also contains a list of ESP-CP-sponsored publications, presentations, and patents. Separate abstracts have been indexed into the energy database for contributions to this proceedings.

  3. Proceedings of the efficient separations and processing crosscutting program 1997 technical exchange meeting

    Gephart, J.M.

    1997-01-01

    This document contains summaries of technology development presented at the 1997 Efficient Separations and Processing Crosscutting Program (ESP-CP) Technical Exchange Meeting (TEM), held January 28-30, 1997, in Gaithersburg, Maryland. The ESP-CP is sponsored by the U.S. Department of Energy's Office of Environmental Management (DOE/EM), Office of Science and Technology. The ESP-CP TEM is held annually to: (1) Present current technology development activities funded by the ESP-CP. Developers of ESP-CP-funded technologies describe the problems and needs addressed by their technologies; the technical approach, accomplishments, and resolution of issues; the strategy and schedule for commercialization; and evolving potential applications. Representatives from DOE/EM's Focus Areas also present their technology needs. (2) Promote the exchange of technical information among those developing new separations technologies, those responsible for providing new separations technologies to meet DOE/EM needs, and those who need or will potentially make use of such technologies. (3) Familiarize the ESP-CP Technical Review Team with the FY 1997 program and solicit reviewers' views on the program as a whole. This meeting is not a program review of the individual tasks, but instead focuses on the technical aspects and implementation of ESP-CP-sponsored technology or data. This document also contains a list of ESP-CP-sponsored publications, presentations, and patents. Separate abstracts have been indexed into the energy database for contributions to this proceedings

  4. Innovative lasers for uranium isotope separation. [Progress report

    Brake, M.L.; Gilgenbach, R.M.

    1991-06-01

    Copper vapor lasers have important applications to uranium atomic vapor laser isotope separation (AVLIS). The authors have spent the first two years of their project investigating two innovative methods of exciting/pumping copper vapor lasers which have the potential to improve the efficiency and scaling of large laser systems used in uranium isotope separation. Experimental research has focused on the laser discharge kinetics of (1) microwave, and (2) electron beam excitation/pumping of large-volume copper vapor lasers. During the first year, the experiments have been designed and constructed and initial data has been taken. During the second year these experiments have been diagnosed. Highlights of some of the second year results as well as plans for the future include the following: Microwave resonant cavity produced copper vapor plasmas at 2.45 GHz, have been investigated. A CW (0--500 W) signal heats and vaporizes the copper chloride to provide the atomic copper vapor. A pulsed (5 kW, 0.5--5kHz) signal is added to the incoming CW signal via a hybrid mixer to excite the copper states to the laser levels. An enhancement of the visible radiation has been observed during the pulsed pardon of the signal. Electrical probe measurements have been implemented on the system to verify the results of the electromagnetic model formulated last year. Laser gain measurements have been initiated with the use of a commercial copper vapor laser. Measurements of the spatial profile of the emission are also currently being made. The authors plan to increase the amount of pulsed microwave power to the system by implementing a high power magnetron. A laser cavity will be designed and added to this system.

  5. The challenge of the future. Technical progress and ecological perspectives

    Jischa, M.F.

    1993-01-01

    The book introduces readers into the interrelated global problems population dynamics, energy supply, imminent climate catastrophe, environmetal pollution, finite resources and the conflict between the North and South. It encourages probing more deeply into the technical challenges of the future. The author demonstrates why economic and technical issues will soon be outstripped by questions of the environmental, human and social compatibility of new technologies. (orig./UA) [de

  6. Nuclear waste glass melter: an update of technical progress

    Brouns, R.A.; Hanson, M.S.

    1984-08-01

    The direct slurry-fed ceramic-lined melter is currently the reference US process for treating defense and civilian high-level liquid waste. Extensive nonradioactive pilot-scale testing at Pacific Northwest Laboratory (PNL) and Savannah River Laboratory has proven the process, defined operating parameters, and identified successful equipment design concepts. Programs at PNL continue to support several of the planned US vitrification plants through preparation of equipment designs and flowsheet testing. Current emphasis is on remotization of equipment, radioactive verification testing, and resolution of remaining technical issues. Development of this technology, technical status, and planned development activities are discussed. 9 references, 4 figures

  7. Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3

    Ulm, Franz-Josef

    2000-01-01

    OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3(NOTE: Part II A item 1 indicates ''PAPER'', but a report is attached electronically)

  8. Annual technical progress report: reactor safety, Government fiscal year 1978

    1978-01-01

    Progress in LMFBR safety studies on accident debris behavior is reported under the following subtask titles: high-temperature-concentration aerosols, large-scale molten fuel tests, sodium release tests, and risk analysis

  9. Technical progress of nuclear energy: economic and environmental prospects

    Naudet, G.

    1994-01-01

    This document deals with three different aspects of the nuclear energy: first the operating and economic performances of nuclear power plants in the world, the French nuclear competitiveness. Then, the technical and economic perspectives about reactors and fuels cycle and the advantages towards atmospheric pollution are discussed to favour a new worldwide nuclear development. (TEC). 8 refs., 4 figs., 6 tabs

  10. Proceedings of the Efficient Separations and Processing Cross-Cutting Program Annual Technical Exchange Meeting

    1995-01-01

    This document contains summaries of technology development presented at the 1995 Efficient Separations and Processing Cross-Cutting Program (ESP) Annual Technical Exchange Meeting. The ESP is sponsored by the US Department of Energy's Office of Environmental Management (EM), Office of Technology Development. The meeting is held annually to promote a free exchange of ideas among technology developers, potential users (for example, EM focus areas), and other interested parties within EM. During this meeting, developers of ESP-funded technologies describe the problems and needs addressed by their technologies; the technical approach, accomplishments, and resolution of issues; the strategy and schedule for commercialization; and evolving potential applications. Presenters are asked to address the following areas: Target waste management problem, waste stream, or data need; scientific background and technical approach; technical accomplishments and resolution of technical issues; schedule and strategy for commercializing and implementing the technology or acquiring needed data; potential alternate applications of the technology or data, including outside of DOE/EM. The meeting is not a program review of the individual tasks or subtasks; but instead focuses on the technical aspects and implementation of ESP-sponsored technology or data. The meeting is also attended by members of the ESP Technical Review Team, who have the opportunity at that time to review the ESP as a whole

  11. Evaporation by mechanical vapor recompression. Technical progress report, September 1-December 31, 1979

    Iverson, C.H.; Coury, G.E.

    1979-01-01

    Progress to date in the development of a study of the application of the technologies of mechanical vapor recompression and falling film evaporators as applied to the beet sugar industry is reported. Progress is reported in the following areas: technical literature search and plant visitations of existing applications of VR/FFE.

  12. Conjoint utility analysis of technical maturity and project progress of construction project

    Ma Wei

    2016-01-01

    Full Text Available In this paper, taking construction project as the research object, the relationship between the project maturity index calculated by the construction project technical risks with different fine degree and the project progress index is studied, and the equilibrium relationship between the Party A’s utility curve and the Party B’s cost curve of using project maturity index and project progress index as the research variables is analyzed. The results show that, when the construction project technical risk division is more precise, the conjoint utility of the project's technical maturity index and the project progress is higher, and the project’s Party A and Party B two sides are closer to the optimal equilibrium. This shows that the construction project technical risk must be finely divided, and managed and controlled respectively, which will help to improve the conjoint utility of the project Party A and Party B two sides.

  13. Recent progress of in-flight separators and rare isotope beam production

    Kubo, Toshiyuki, E-mail: kubo@ribf.riken.jp

    2016-06-01

    New-generation in-flight separators are being developed worldwide, including the Super-FRS separator at the GSI Facility for Antiproton and Ion Research (FAIR), the ARIS separator at the Michigan State University (MSU) Facility for Rare Isotopes Beams (FRIB), and the BigRIPS separator at the RIKEN RI Beam Factory (RIBF), each of which is aimed at expanding the frontiers of rare isotope (RI) production and advancing experimental studies on exotic nuclei far from stability. Here, the recent progress of in-flight separators is reviewed, focusing on the advanced features of these three representative separators. The RI beam production that we have conducted using the BigRIPS separator at RIKEN RIBF is also outlined.

  14. Technical Progress and Development Directions of Oceanic Spatial Information Datum

    BAO Jingyang

    2017-10-01

    Full Text Available This paper briefly analyzes the basic development and technical situation of oceanic spatial information datum, reviews the main processes of oceanic vertical datum and correlative oceanic tidal study, such as improvement and perfect methods of determining tidal station vertical datum, realizing form of vertical datum controlled by tidal station, effect on maintaining vertical datum by long-term tidal station, oceanic tidal model establishing, and also construction and transformation of tidal datum, and then forecasts the key development directions of oceanic spatial information datum on high-accuracy marine position service, vertical datum and the transferring model refinement and spatial datum application.

  15. Quarterly technical progress report, February 1, 1996--April 30, 1996

    NONE

    1996-05-28

    This report from the Amarillo National REsource Center for PLutonium provides research highlights and provides information regarding the public dissemination of information. The center is a a scientific resource for information regarding the issues of the storage, disposition, potential utilization and transport of plutonium, high explosives, and other hazardous materials generated from nuclear weapons dismantlement. The center responds to informational needs and interpretation of technical and scientific data raised by interested parties and advisory groups. Also, research efforts are carried out on remedial action programs and biological/agricultural studies.

  16. Crystalline Repository Project. Technical progress report, October 1982-March 1983

    1985-01-01

    This document reports the progress being made periodically on the development of a geologic repository in crystalline rock for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Crystalline Respository Development (OCRD), a prime contractor of the US Department of Energy Repository Project Office. The studies include work by other prime contractors and by subcontractors to OCRD

  17. C-Mod Collaboration Informal Technical Progress Report

    Kenneth W. Gentle

    2007-01-01

    The aims of the collaboration have not changed. A specific list of tasks was agreed upon during the Fall of 2006 in preparation for the 2007 C-Mod campaign by Earl Marmar, Head of the Alcator Project, Kenneth Gentle, Principal Investigator, and William Rowan, Collaboration Coordinator with the facilitation of Adam Rosenberg (DOE grant monitor for the collaboration). The activities follow the list of tasks and are discussed in this progress report

  18. Recent progress in fission product separation; Progres recents de la separation des produits de fission

    Raggenbass, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Successful experiments have been done on the method described at Geneva in 1958. The process has been considerably improved: 1 - Initially, the caesium phospho tungstate precipitate was leached barium hydroxide in the centrifuge and this was followed by a distillation of ammonia in a concentrator. The barium hydroxide was then eliminated by carbonate precipitation and centrifugation. It has been proved that the ammonia distillation could be replaced by its evaporation during centrifugation, thus eliminating the need of a concentrator. It was then possible to carry out the carbonation on the solide-liquid mixture produced by the baryte water leaching. 2 - In applying the above process to the treatment of solutions derived from uranium molybdenum fuels, concentrating is to be recommended in order to hold the molybdenum in solution by complexing it with phosphoric acid. This complexing process provides a suspension of zirconium phosphate and ammonium phospho tungstate. These are separated by passing into a basic medium which precipitates the zirconium oxide, then turning back to an acid medium; the end of the treatment remains unchanged. 3 - Studies carried out in several countries on the exchange properties of hetero-polyacid salts have always met with difficulties as a result of the poor mechanical properties of these substances. This difficulty has been overcome by wrapping the ammonium phospho tungstate in a zirconium phosphate matrix. The exchanger obtained possesses: satisfactory mechanical properties, - a capacity of 0.1 milli equivalent per gram in concentrated nitric acid solution. It can be eluted and regenerated by a solution of an ammonium salt. The procedure for recovery of these various fission products is briefly the following: extraction of rare earths by di-2-ethyl hexyl phosphoric acid into dodecane at pH 2, the chemical impurities being complexed by citric acid, extraction of most of the magnesium at pH 4 by the same solvents the solvent being

  19. Progress report of Technical Physics Division: April 1980 - March 1982

    Chaudhry, Ramesh; Vijendran, P.

    1983-01-01

    Activities, with an individual summary of each, of the Technical Physics Division (TPD) of the Bhabha Atomic Research Centre (BARC), Bombay are reported for the period April 1980 - March 1982. The major thrust of the TPD's work has been in: (i) design and fabrication of instruments, devices and equipment and (ii) development of techniques in the frontline research and technology areas like vacuum science, surface analysis, cryogenics and crystal growing. The Division also provided custombuilt electronics equipment, vacuum systems and glass components and devices to the various Divisions of BARC and other units of the DAE. Training and manpower development activities and technology transfer activities are also reported. Lists of seminars, colloquia, publications during the period of the report are given. (M.G.B.)

  20. Progress report for 1978-79, Technical Physics Division

    Gopalaraman, C.P.; Deshpande, R.Y.

    1980-01-01

    The research and development activities of the Technical Physics Division (TPD) of the Bhabha Atomic Research Centre, Bombay, during the calendar years 1978 and 1979 are reported. The TPD's major areas of work are electronics instrumentation, crystal technology, mass spectrometers, cryogenic equipment and vacuum equipment. Some of the major achievements are: (1) fabrication of various electronic instruments and components for the pulsed nuclear magnetic resonance spectrometers, (2) growth of large size NaI(Tl) and Ge crystals, (3) growth of CsI, KDP and arsenic selenide crystals, (4) fabrication of quadrupole mass filters and (5) fabrication of mass spectrometers for gas analysis and D/H analysis in water samples. (M.G.B.)

  1. Electronic refrigerant leak detector. Quarterly technical progress report

    Talamas, E. Jr.

    1998-10-15

    The project comprises three main tasks. They are (1) Develop, design, and fabricate sensors, (2) Develop, design, and fabricate test instruments, (3) Testing and data analysis. The milestone includes 17 sub-tasks for the 52-weeks project period, starting on May 1, 1998 and ending on April 30, 1999. As stated in the Application for Federal Assistance, Micronic intended to relocate to a new office by June of 1998. This decision was delayed, since the first partial payment was transferred on August 12, 1998. Micronic plans to relocate this November. A second Provisional Application for a US patent has been filed. Progress made during this period is reported.

  2. Nuclear Safety: Volume 29, No. 3: Technical progress review

    Silver, E G [ed.

    1988-07-01

    Nuclear Safety is a review journal that covers significant development in the field of nuclear safety. Its scope included the analysis and control of hazards associated with nuclear energy, operations involving fissionable materials and the products of nuclear fission and their effects on the environment. Primary emphasis is on safety in reactor design, construction, and operation; however, the safety aspects of the entire fuel cycle, including fuel fabrication, spent-fuel processing, nuclear waste disposal, handling of radioisotopes, and environmental effects of these operations, are also treated. Individual papers have been cataloged separately.

  3. The role of technical progress in the process of recalculating oil reserves

    Boulard, J.N.

    1999-01-01

    Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

  4. Technical progress report, October 1, 1980-September 30, 1981

    1981-01-01

    Progress during the 12-month period, October 1, 1980 to September 30, 1981 on the University of Wisconsin Plasma Physics contract is described. Most of the work centers around two major experimental devices, the Levitated Octupole and Tokapole II. A major upgrade of the Octupole is underway to include 2 MW of ICRH and 1.8 MW of neutral beam heating. Meanwhile, gun optimization and low field operation has resulted in the attainment of 35% beta, a factor of 9 above the single fluid ballooning limit. The ICRH experiment is well underway, and the first neutral beam source has been installed. The Tokapole is operating reliably at the full design field of 10 kG with 12 msec discharges. Low q (approx. 0.4) discharges with flat current profiles are obtained at reduced (approx. 3kG) toroidal field. The device is presently being used to study shear Alfven wave heating, ECRH startup, poloidal ohmic heating, and plasma transport

  5. TECHNICAL TRAINING SEMINAR: High Temperature Superconductors: Progress and Issues

    Davide Vitè

    2002-01-01

    Monday 24 June from 14:30 to 15:30 - Training Centre Auditorium - bldg. 593-11 High Temperature Superconductors: Progress and Issues Prof. Jan Evetts / UNIVERSITY OF CAMBRIDGE, Department of Materials Science and Metallurgy, UK Grappling with grain boundaries: Current transport processes in granular High Temperature Superconductors (HTS) The development of High Temperature Superconductors, seen from a materials scientist's point of view, is relevant to the superconductivity community at CERN: their possible high current applications can include high performance magnets for future accelerators. There is an urgent need to develop a quantitative description of HTS conductors in terms of their complex anisotropy, inhomogeneity and dimensionality. This is essential both for the practical specification of a conductor and for charting routes to conductor optimisation. The critical current, the n-value, dissipation and quenching characteristics are amongst most important parameters that make up an engineering specifi...

  6. Technical progress review of extraction of uranium from fly ash

    Gao Renxi; Gao Junning; Wu Qingming; Chen Gang; Wan Hongjin; Zhang Ziyue

    2014-01-01

    The increasing of fly ash in coal-fired power plants at home and abroad year by year and the potential impacts to the environment attracted media attention. Although the extraction of uranium from the fly ash in coal-fired power plants had optional process from technique aspect and sufficient preliminary researches, but considering the low grade of the uranium in fly ash and particularity of the mineral composition, it is easy to have a high cost of extraction. As a consequence, it is not included in the development plan of uranium mining and metallurgy. The present applications of fly ash are only building materials, building roads and pit valley backfill, the resource utilization rate was low and was still in its early stages of development and application. In view of this, the research advances and the latest development trends of extraction of uranium from fly ash at home and abroad were introduced from the technical aspect, and the beneficial analyzes of the prospect and advices to this industry were given. (authors)

  7. Development and technical implementation of the separation nozzle process for enrichment of uranium 235

    Syllus Martins Pinto, C.; Voelcker, H.; Becker, E.W.

    1977-12-01

    The separation nozzle process for the enrichment of uranium-235 has been developed at the Karlsruhe Nuclear Research Center as an alternative to the gaseous diffusion and centrifuge process. The separation of uranium isotopes is achieved by the deflection of a jet of uranium hexafluoride mixed with hydrogen. Since 1970, the German company of STEAG, has been involved in the technological development and commercial implementation of the nozzle process. In 1975, the Brazilian company of NUCLEBRAS, and the German company of Interatom, joined the effort. The primary objective of the common activity is the construction of a separation nozzle demonstration plant with an annual capacity of about 200 000 SWU and the development of components of a commercial plant. The paper covers the most important steps in the development and the technical implementation of the process. (orig.) [de

  8. Texas Experimental Tokamak, a plasma research facility: Technical progress report

    Wootton, A.J.

    1995-08-01

    In the year just past, the authors made major progress in understanding turbulence and transport in both core and edge. Development of the capability for turbulence measurements throughout the poloidal cross section and intelligent consideration of the observed asymmetries, played a critical role in this work. In their confinement studies, a limited plasma with strong, H-mode-like characteristics serendipitously appeared and received extensive study though a diverted H-mode remains elusive. In the plasma edge, they appear to be close to isolating a turbulence drive mechanism. These are major advances of benefit to the community at large, and they followed from incremental improvements in diagnostics, in the interpretation of the diagnostics, and in TEXT itself. Their general philosophy is that the understanding of plasma physics must be part of any intelligent fusion program, and that basic experimental research is the most important part of any such program. The work here demonstrates a continuing dedication to the problems of plasma transport which continue to plague the community and are an impediment to the design of future devices. They expect to show here that they approach this problem consistently, systematically, and effectively

  9. ERIP invention 637. Technical progress report 2nd quarter, April 1997--June 1997

    Thacker, G.W.

    1997-07-22

    This technical report describes progress in the development of the Pegasus plow, a stalk and root embedding apparatus. Prototype testing is reported, and includes the addition of precision tillage. Disease data, organic matter, and nitrogen levels results are very briefly described. Progress in marketing is also reported. Current marketing issues include test use by cotton and wheat growers, establishment of dealer relationships, incorporation of design modifications, expansion of marketing activities, and expansion of loan and lease program.

  10. Technical progress in INPRO activities on modelling and innovation

    Villalibre, P.; Haas, E.; Khartabil, H.; Kim, S.; Korinny, A.; Usanov, V. and others

    2010-01-01

    Among the 31 Members of the 'International Project on Innovative Nuclear Reactors and Fuel Cycles' (INPRO) in April 2010, more than 20 are cooperating in the implementation of Collaborative Projects (CPs) related to the four substantive Programme Areas of the INPRO Action Plan. The purpose of the CPs is to contribute to the achievement of goals established in the programmatic areas. This paper presents progress status of several CPs dealing with Modelling and Innovation: - CP on Environmental Impact Benchmarking applicable to Nuclear Energy Systems under Normal Operation (ENV): A benchmark of codes and methods for determining radiation released during normal operation of nuclear facilities is performed by using established source term, release scenario, and target group (humans). - CP on Proliferation Resistance: Acquisition/Diversion Pathway Analysis (PRADA): 'PRADA' addresses the identification and analyses of high level pathways for the acquisition of weapons usable material, and makes recommendations for evaluating the multiplicity and robustness of barriers against proliferation. PRADA develops a case study based on DUPIC fuel cycle. The outcome from the project will support the assessment methodologies developed at GIF and INPRO. - CP on Global Architecture of Nuclear Energy Systems based on Thermal and Fast Reactors including Closed Fuel Cycle (GAINS): GAINS objective is to develop a methodological platform for assessing future nuclear energy systems taking into account the sustainable development, and to validate the results through sample analyses. High and moderate scenarios of nuclear energy demand and supply during the Century (5000 and 2500 GWe respectively in the year 2100) are being analysed using homogeneous and heterogeneous considerations. A non-geographic approach grouping the countries according to their planned use of nuclear energy has being established. - CP on Investigations of the 233 U/Th Fuel Cycle (ThFC): ThFC objective is to explore FC

  11. Technical and economic feasibility of membrane technology. Fourth technical progress report, June 17-September 16, 1980

    Sandre, A.

    1980-10-01

    Progress is reported on the investigation of the potential application of reverse osmosis, ultrafiltration and electrodialysis to the system of solids concentration in beet sugar process streams. During this period, emphasis was put on running reverse osmosis tests with a new prototype machine to select the most suitable membranes for the concentrating of sugar solutions. An economic analysis of using reverse osmosis in a factory producing 10/sup 6/ gal/day of thin juice is discussed. (DMC)

  12. Institutional effectiveness of REDD+ MRV: Countries progress in implementing technical guidelines and good governance requirements

    Ochieng, R.M.; Visseren-Hamakers, Ingrid; Arts, B.; Brockhaus, M.; Herold, M.

    2016-01-01

    The UNFCCC requires REDD+ countries wishing to receive results-based payments to measure, report and verify (MRV) REDD+ impacts; and outlines technical guidelines and good governance requirements for MRV. This article examines institutional effectiveness of REDD+ MRV by assessing countries’ progress

  13. Studies in theoretical high energy particle physics: Technical progress report [February 1987-February 1988

    Sukhatme, U.P.; Keung, Wai-Yee; Kovacs, E.

    1988-02-01

    This is a technical progress report for grant No. FG02-84ER40173 for the period February 1987 to February 1988. Our research on supersymmetric quantum mechanics has yielded many interesting results. In particular, a systematic approach to the tunneling problem in double well potentials has been developed. Higgs boson related physics at the high energy hadron colliders has been extensively studied

  14. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1--July 31, 1998

    NONE

    1998-09-01

    Progress is reported on research projects related to the following: Electronic resource library; Environment, safety, and health; Communication, education, training, and community involvement; Nuclear and other materials; and Reporting, evaluation, monitoring, and administration. Technical studies investigate remedial action of high explosives-contaminated lands, radioactive waste management, nondestructive assay methods, and plutonium processing, handling, and storage.

  15. Cassini RTG Program. Monthly technical progress report, 27 November--31 December 1995

    1996-01-01

    This monthly technical progress report provided information on the following tasks: spacecraft integration and liaison; engineering support; safety analysis; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, and reliability, and contractor acquired government owned (CAGO) property acquisition

  16. Technical progress faced with the challenges of the energy sector in the future

    Maillard, D.

    1999-01-01

    The colloquium organised by the Association of Energy Economists dealing with the theme 'Technical progress faced with the challenges of the energy sector in the future' takes place against a backdrop of ever-increasing initiatives in this field, for example at the World Energy Council or the International Energy Agency Faith in technical progress is widespread but should be supported by studies without any preconceived ideas. Research and development efforts must be fully supported, and in a climate of opening markets and liberalization the public authorities have a major role to pay. Historically, the markets have always been able to meet new needs thanks to technology, but the ambitious targets that the international community has set itself regarding the emission of greenhouse gases imply technical improvements and major investments. (authors)

  17. Separate collection of plastic waste, better than technical sorting from municipal solid waste?

    Feil, Alexander; Pretz, Thomas; Jansen, Michael; Thoden van Velzen, Eggo U

    2017-02-01

    The politically preferred solution to fulfil legal recycling demands is often implementing separate collection systems. However, experience shows their limitations, particularly in urban centres with a high population density. In response to the European Union landfill directive, mechanical biological waste treatment plants have been installed all over Europe. This technology makes it possible to retrieve plastic waste from municipal solid waste. Operators of mechanical biological waste treatment plants, both in Germany and the Netherlands, have started to change their mechanical separation processes to additionally produce plastic pre-concentrates. Results from mechanical biological waste treatment and separate collection of post-consumer packaging waste will be presented and compared. They prove that both the yield and the quality of plastic waste provided as feedstock for the production of secondary plastic raw material are largely comparable. An economic assessment shows which conditions for a technical sorting plant are economically attractive in comparison to separate collection systems. It is, however, unlikely that plastic recycling will ever reach cost neutrality.

  18. Technical meeting on progress in managing, and limiting the consequences of events exceeding the design basis

    Fabian, H.

    2004-01-01

    The Technical Groups on 'Reactor Safety' and 'Thermodynamics and Fluid Dynamics' of the Kerntechnische Gesellschaft e.V. organized a joint technical meeting on 'Progress in Managing, and Limiting the Consequences of, Events Exceeding the Design Basis' at the FTU Training Center of the Karlsruhe Research Center. The topic chosen, the papers presented, the presenters, and the non-technical part of the program met with lively interest on the part of institutions in the nuclear field. These were the objectives of the technical meeting: - Establishing a forum for communicating relevant topics. - In-depth discussion of the main topic, i.e. the advanced development of reactor safety, research in the field, and its application, in twenty selected papers presented by speakers from different institutions. - Presentation of topical work in a nuclear technology institution, the Karlsruhe Research Center. (orig.) [de

  19. Recent progress of chiral stationary phases for separation of enantiomers in gas chromatography.

    Xie, Sheng-Ming; Yuan, Li-Ming

    2017-01-01

    Chromatography techniques based on chiral stationary phases are widely used for the separation of enantiomers. In particular, gas chromatography has developed rapidly in recent years due to its merits such as fast analysis speed, lower consumption of stationary phases and analytes, higher column efficiency, making it a better choice for chiral separation in diverse industries. This article summarizes recent progress of novel chiral stationary phases based on cyclofructan derivatives and chiral porous materials including chiral metal-organic frameworks, chiral porous organic frameworks, chiral inorganic mesoporous materials, and chiral porous organic cages in gas chromatography, covering original research papers published since 2010. The chiral recognition properties and mechanisms of separation toward enantiomers are also introduced. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Total Factor Productivity Growth, Technical Progress & Efficiency Change in Vietnam Coal Industry - Nonparametric Approach

    Phuong, Vu Hung

    2018-03-01

    This research applies Data Envelopment Analysis (DEA) approach to analyze Total Factor Productivity (TFP) and efficiency changes in Vietnam coal mining industry from 2007 to 2013. The TFP of Vietnam coal mining companies decreased due to slow technological progress and unimproved efficiency. The decadence of technical efficiency in many enterprises proved that the coal mining industry has a large potential to increase productivity through technical efficiency improvement. Enhancing human resource training, technology and research & development investment could help the industry to improve efficiency and productivity in Vietnam coal mining industry.

  1. Productivity Change, Technical Progress, and Relative Efficiency Change in the Public Accounting Industry

    Rajiv D. Banker; Hsihui Chang; Ram Natarajan

    2005-01-01

    We present evidence on components of productivity change in the public accounting industry toward the end of the 20th century. Using revenue and human resource data from 64 of the 100 largest public accounting firms in the United States for the 1995--1999 period, we analyze productivity change, technical progress, and relative efficiency change over time. The average public accounting firm experienced a productivity growth of 9.5% between 1995 and 1999. We find support for the hypothesis that...

  2. Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1994

    1994-05-01

    West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Reports on a quarterly basis. This report comprises the first Quarterly Technical Progress Report for Year 2 of the Agreement. This report reflects the progress and/or efforts performed on the sixteen (16) technical projects encompassed by the Year 2 Agreement for the period of January 1 through March 31, 1994. In situ bioremediation of chlorinated organic solvents; Microbial enrichment for enhancing in-situ biodegradation of hazardous organic wastes; Treatment of volatile organic compounds (VOCs) using biofilters; Drain-enhanced soil flushing (DESF) for organic contaminants removal; Chemical destruction of chlorinated organic compounds; Remediation of hazardous sites with steam reforming; Soil decontamination with a packed flotation column; Use of granular activated carbon columns for the simultaneous removal of organics, heavy metals, and radionuclides; Monolayer and multilayer self-assembled polyion films for gas-phase chemical sensors; Compact mercuric iodide detector technology development; Evaluation of IR and mass spectrometric techniques for on-site monitoring of volatile organic compounds; A systematic database of the state of hazardous waste clean-up technologies; Dust control methods for insitu nuclear and hazardous waste handling; Winfield Lock and Dam remediation; and Socio-economic assessment of alternative environmental restoration technologies.

  3. Progress on Incorporating Zeolites in Matrimid®5218 Mixed Matrix Membranes towards Gas Separation

    Roberto Castro-Muñoz

    2018-06-01

    Full Text Available Membranes, as perm-selective barriers, have been widely applied for gas separation applications. Since some time ago, pure polymers have been used mainly for the preparation of membranes, considering different kinds of polymers for such preparation. At this point, polyimides (e.g., Matrimid®5218 are probably one of the most considered polymers for this purpose. However, the limitation on the performance relationship of polymeric membranes has promoted their enhancement through the incorporation of different inorganic materials (e.g., zeolites into their matrix. Therefore, the aim of this work is to provide an overview about the progress of zeolite embedding in Matrimid®5218, aiming at the preparation of mixed matrix membranes for gas separation. Particular attention is paid to the relevant experimental results and current findings. Finally, we describe the prospects and future trends in the field.

  4. Progressive white-matter disease with primary cerebellar involvement: a separate entity?

    Yalcinkaya, C. [Division of Child Neurology, Department of Neurology, Cerrahpasa Medical Faculty, Istanbul University, Istanbul (Turkey); Arslanoglu, I. [Division of Endocrinology, Department of Paediatrics, Goeztepe Hospital, Istanbul (Turkey); Islak, C. [Division of Neuroradiology, Department of Radiology, Cerrahpasa Medical Faculty, Istanbul University, Istanbul (Turkey); Aydin, A. [Division of Metabolic Disease, Department of Paediatrics, Cerrahpasa Medical Faculty, Istanbul University, Istanbul (Turkey); Boltshauser, E. [Division of Paediatric Neurology, University Children' s Hospital, Steinwiesstrasse 75, 8032 Zuerich (Switzerland)

    2002-09-01

    Although its metabolic basis has not yet been clarified, we report a progressive white-matter disease in a Turkish girl, starting in the cerebellum and spreading to supratentorial white matter. The onset was at the age of 2.5 years with diabetes insipidus, followed by ataxia and pyramidal signs resulting in loss of walking. Aqueduct stenosis was first recognised at the age of 8 years. To our knowledge, this MRI and clinical pattern does not correspond to a recognised, well-defined white-matter disease and may indicate a separate entity. (orig.)

  5. Progressive white-matter disease with primary cerebellar involvement: a separate entity?

    Yalcinkaya, C.; Arslanoglu, I.; Islak, C.; Aydin, A.; Boltshauser, E.

    2002-01-01

    Although its metabolic basis has not yet been clarified, we report a progressive white-matter disease in a Turkish girl, starting in the cerebellum and spreading to supratentorial white matter. The onset was at the age of 2.5 years with diabetes insipidus, followed by ataxia and pyramidal signs resulting in loss of walking. Aqueduct stenosis was first recognised at the age of 8 years. To our knowledge, this MRI and clinical pattern does not correspond to a recognised, well-defined white-matter disease and may indicate a separate entity. (orig.)

  6. The 11th International ICIT Conference Progress in Cryogenics and Isotopes Separation. Proceedings

    Stefanescu, Ioan

    2005-01-01

    The proceedings of the 11th International ICIT Conference Progress in Cryogenics and Isotopes Separation held in Caciulata, Romania on 12-14 October 2005 contain plenary lectures (6 papers) and 6 sections addressing the following subject matters: Section 1. Stable Isotopes Physics. Technologies and Applications (5 papers); Section 2. Science and Materials Engineering (11 papers); Section 3. Nuclear Power (21 papers); Section 4. Hydrogen and Fuel Cells (7 papers); Section 5. Environmental Protection. Industrial Risk (10 papers); Section 6. Laboratory Analysis Methods (10 papers). Twenty two papers are available in abstract form only and full text entered the corresponding records

  7. The 12th International ICIT Conference Progress in Cryogenics and Isotopes Separation. Proceedings

    Stefanescu, Ioan

    2006-01-01

    The proceedings of the 12th International ICIT Conference Progress in Cryogenics and Isotopes Separation held in Caciulata, Romania on 25-27 October 2006 contain plenary lectures (11 papers) and 7 sections addressing the following subject matters: Section 1. Stable Isotopes Physics. Technologies and Applications (6 papers); Section 2. Cryogenics Technologies and Equipment (6 papers); Section 3. Science and Materials Engineering (18 papers); Section 4. Nuclear Power (17 papers); Section 5. Hydrogen and Fuel Cells (14 papers); Section 6. Environmental Protection. Industrial Risk (14 papers); Section 7. Laboratory Analysis Methods (13 papers). A number of 40 papers are available in abstract form only and accordingly full text entered the corresponding records

  8. Experimental Facilities Division/User Program Division technical progress report 1999-2000

    2001-01-01

    In October 1999, the two divisions of the Advanced Photon Source (APS), the Accelerator Systems Division (ASD) and the Experimental Facilities Division (XFD), were reorganized into four divisions (see high-level APS organizational chart, Fig. 1.1). In addition to ASD and XFD, two new divisions were created, the APS Operations Division (AOD), to oversee APS operations, and the User Program Division (UPD), to serve the APS user community by developing and maintaining the highest quality user technical and administration support. Previous XFD Progress Reports (ANL/APS/TB-30 and ANL/APS/TB-34) covered a much broader base, including APS user administrative support and what was previously XFD operations (front ends, interlocks, etc.) This Progress Report summarizes the main scientific and technical activities of XFD, and the technical support, research and development (R and D) activities of UPD from October 1998 through November 2000. The report is divided into four major sections, (1) Introduction, (2) SRI-CAT Beamlines, Technical Developments, and Scientific Applications, (3) User Technical Support, and (4) Major Plans for the Future. Sections 2 and 3 describe the technical activities and research accomplishments of the XFD and UPD personnel in supporting the synchrotron radiation instrumentation (SRI) collaborative access team (CAT) and the general APS user community. Also included in this report is a comprehensive list of publications (Appendix 1) and presentations (Appendix 2) by XFD and UPD staff during the time period covered by this report. The organization of section 2, SRI CAT Beamlines, Technical Developments, and Scientific Applications has been made along scientific techniques/disciplines and not ''geographical'' boundaries of the sectors in which the work was performed. Therefore items under the subsection X-ray Imaging and Microfocusing could have been (and were) performed on several different beamlines by staff in different divisions. The management of

  9. Volatiles combustion in fluidized beds. Technical progress report, 4 March 1993--3 June 1993

    Hesketh, R.P.

    1993-09-01

    The goal of this project is to investigate the conditions in which volatiles will burn within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization will be performed to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. The work conducted during the period 4 March, 1993 through 3 June, 1993 is reported in this technical progress report. The work during this time period consists primarily of the startup and trouble shooting of the fluidized bed reactor and gas phase modeling of methane and propane.

  10. National Council on Radiation Protection and Measurements semiannual technical progress report, March 1989--August 1989

    Ney, W.R.

    1991-01-01

    This semiannual technical progress report is for the period 1 March 1989 through 31 August 1989. This National Council on Radiation Protection and Measurements (NCRP) program is designed to provide recommendations for radiation protection based on scientific principles. During this period several reports were published covering the topics of occupational radiation exposure, medical exposure, radon control, dosimetry, and radiation protection standards. Accomplishments of various committees are also reported; including the committees on dental x-ray protection, radiation safety in uranium mining and milling, ALARA, instrumentation, records maintenance, occupational exposures of medical personnel, emergency planning, and others. (SM)

  11. Technical progress and efficiency changes in football teams participating in the UEFA Champions League

    Lucía Isabel García Cebrián

    2015-09-01

    Full Text Available This paper commits to calculate and analyze productivy levels and its components for teams that participated in the UEFA Champions League between 2003 and 2012. It will pursue three objectives: 1 evaluate resources usage, 2 analyze the productivity levels of the football teams and the sports results, and 3 see the influence of participation experience in reference to productivity and sports results. Using Malmquist Productivity Index, the results reflect a lack of consistent progression of efficiency, productivity, and technical change. This competition does not reward the efficient usage of resources and there is not a conclusive relationshop between permanence in the competition and productivity.

  12. Western Research Institute: Annual technical progress report, October 1987--September 1988

    1988-12-01

    This report describes the technical progress made by the Western Research Institute of the University of Wyoming Research Institute of the University of Wyoming Research Corporation on work performed for the period October 1, 1987 through September 30, 1988. This research involves five resource areas: oil shale, tar sand, underground coal gasification, advanced process technology, and advanced fuels research. Under the terms of the cooperative agreement, an annual project plan has been approved by DOE. The work reported herein reflects the implementation of the research in the plan and follows the structure used therein. 49 refs., 32 figs., 87 tabs.

  13. Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1993

    1993-04-01

    This reports reports the progress/efforts performed on six technical projects: 1. systematic assessment of the state of hazardous waste clean-up technologies; 2. site remediation technologies (SRT):drain- enhanced soil flushing for organic contaminants removal; 3. SRT: in situ bio-remediation of organic contaminants; 4. excavation systems for hazardous waste sites: dust control methods for in-situ nuclear waste handling; 5. chemical destruction of polychlorinated biphenyls; and 6. development of organic sensors: monolayer and multilayer self-assembled films for chemical sensors.

  14. Nuclear structure theory. Annual technical progress report, October 1, 1976--September 30, 1977

    French, J.B.; Koltun, D.S.

    1977-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: (1) statistical spectroscopy, including giant resonances for beta and electromagnetic excitation and sum rules (including inverse-energy-weighted sum rules), statistical methods of truncating shell model spaces and renormalization of operators, study of state labelling and ''chains'' of groups, evaluation of fluctuation measures, technical aspects of operator averaging; (2) meson interactions with nuclei, including scattering and absorption of mesons by nuclei (general methods), models for absorption, single- and double-charge exchange of pions, role of rho mesons

  15. Testing a technical-scale counterflow compact heat exchanger for the separation of uranium hexafluoride from hydrogen

    Hornberger, P.; Seidel, D.; Steinhaus, H.

    1981-07-01

    When enriching the light uranium isotope U-235 according to the separation nozzle method, UF 6 and light auxiliary gas (H 2 ) must be separated from each other at the head as well as at the shoulder of the cascade. After pre-separation at a special separation nozzle stage, fine separation is planned by means of a low-temperature separator made as a compact heat exchanger. This report describes first testing under process conditions of a representative section of the separator blocks intended for technical-scale operation. It is proved that the rated loading capacity is attained while the residual UF 6 concentration contained in the escaping hydrogen can be lowered down to values less than 1 ppm. It is further shown that the requirement of constant pressure drop at the separator, which is decisive for the smooth interplay of preseparator stage and low-temperature separator, can be imposed by direct control of the supply of the refrigerating medium through the variable to be kept constant. A concept of control is proposed for industrial application necessitating the operation of several low-temperature separators staggered in terms of time. This concept allows the relatively simple optimum utilization of the separator capacity even under variable operating conditions. (orig.) [de

  16. Sex composition of children, parental separation, and parity progression: Is Finland a Nordic outlier?

    Jan Saarela

    2014-01-01

    Full Text Available Background: Previous studies that have studied parental gender preferences for children have analysed either divorce or parity progression. We use Finnish register data that make it possible to study both events simultaneously by following the same couples with children over time. Objective: Our aim is to study how the sex composition of children relates to parental separation and continued childbearing, considering that within the same institutional context both aspects likely reflect gender preferences for children. Methods: We perform parity-specific Cox regressions where parity progression and separation (divorce or split up are treated as two competing events. Results: Our results suggest that, in the 1970s and early 1980s, there was a parental boy preference in Finland, which makes the country different from its Nordic neighbours. Both the risks of divorce and continued childbearing were higher among couples with only girls than among those with only boys. This difference had attenuated considerably since the 1970s, and was practically non-existent in the 1990s. Complementary analyses of married and cohabiting couples' risk of split up and continued childbearing support the conclusion. Conclusions: As compared with the other Nordic countries, Finland seems to have experienced a later development of implementing modern family roles and a more egalitarian distribution of parents' attention to sons and daughters. The lag might be due to a relatively late and fast industrialisation and urbanisation process. Comments: Like in the United States, the boy preference seems to have attenuated over time, which would be in correspondence with an increased secularisation and gender equalisation of society.

  17. Determination of technical and economic parameters of an ionic transport membrane air separation unit working in a supercritical power plant

    Kotowicz Janusz

    2016-09-01

    Full Text Available In this paper an air separation unit was analyzed. The unit consisted of: an ionic transport membrane contained in a four-end type module, an air compressor, an expander fed by gas that remains after oxygen separation and heat exchangers which heat the air and recirculated flue gas to the membrane operating temperature (850 °C. The air separation unit works in a power plant with electrical power equal to 600 MW. This power plant additionally consists of: an oxy-type pulverized-fuel boiler, a steam turbine unit and a carbon dioxide capture unit. Life steam parameters are 30 MPa/650 °C and reheated steam parameters are 6 MPa/670 °C. The listed units were analyzed. For constant electrical power of the power plant technical parameters of the air separation unit for two oxygen recovery rate (65% and 95% were determined. One of such parameters is ionic membrane surface area. In this paper the formulated equation is presented. The remaining technical parameters of the air separation unit are, among others: heat exchange surface area, power of the air compressor, power of the expander and auxiliary power. Using the listed quantities, the economic parameters, such as costs of air separation unit and of individual components were determined. These quantities allowed to determine investment costs of construction of the air separation unit. In addition, they were compared with investment costs for the entire oxy-type power plant.

  18. Projects at the component development and integration facility. Quarterly technical progress report, April 1, 1994--June 30, 1994

    1994-01-01

    This quarterly technical progress report presents progress on the projects at the Component Development and Integration Facility (CDIF) during the third quarter of FY94. The CDIF is a major Department of Energy test facility in Butte, Montana, operated by MSE, Inc. Projects in progress include: Biomass Remediation Project; Heavy Metal-Contaminated Soil Project; MHD Shutdown; Mine Waste Technology Pilot Program; Plasma Projects; Resource Recovery Project; and Spray Casting Project

  19. Surgical resident technical skill self-evaluation: increased precision with training progression.

    Quick, Jacob A; Kudav, Vishal; Doty, Jennifer; Crane, Megan; Bukoski, Alex D; Bennett, Bethany J; Barnes, Stephen L

    2017-10-01

    Surgical resident ability to accurately evaluate one's own skill level is an important part of educational growth. We aimed to determine if differences exist between self and observer technical skill evaluation of surgical residents performing a single procedure. We prospectively enrolled 14 categorical general surgery residents (six post-graduate year [PGY] 1-2, three PGY 3, and five PGY 4-5). Over a 6-month period, following each laparoscopic cholecystectomy, residents and seven faculty each completed the Objective Structured Assessment of Technical Skills (OSATS). Spearman's coefficient was calculated for three groups: senior (PGY 4-5), PGY3, and junior (PGY 1-2). Rho (ρ) values greater than 0.8 were considered well correlated. Of the 125 paired assessments (resident-faculty each evaluating the same case), 58 were completed for senior residents, 54 for PGY3 residents, and 13 for junior residents. Using the mean from all OSATS categories, trainee self-evaluations correlated well to faculty (senior ρ 0.97, PGY3 ρ 0.9, junior ρ 0.9). When specific OSATS categories were analyzed, junior residents exhibited poor correlation in categories of respect for tissue (ρ -0.5), instrument handling (ρ 0.71), operative flow (ρ 0.41), use of assistants (ρ 0.05), procedural knowledge (ρ 0.32), and overall comfort with the procedure (ρ 0.73). PGY3 residents lacked correlation in two OSATS categories, operative flow (ρ 0.7) and procedural knowledge (ρ 0.2). Senior resident self-evaluations exhibited strong correlations to observers in all areas. Surgical residents improve technical skill self-awareness with progressive training. Less-experienced trainees have a tendency to over-or-underestimate technical skill. Copyright © 2017 Elsevier Inc. All rights reserved.

  20. Supramolecular structures for photochemical energy conversion. Technical progress report, 1993--1996

    NONE

    1996-06-01

    This research project is concerned with the design, synthesis and study by photochemical and spectroscopic methods of complex molecular devices that mimic some important aspects of photosynthetic electron and energy transfer. Properly engineered molecules of this type can functionally mimic photosynthetic light harvesting (singlet-singlet energy transfer between chromophores), photoprotection from light-initiated singlet oxygen damage (triplet-triplet energy transfer from chlorophylls to carotenoid polyenes), and, most importantly, photoinduced multistep electron transfer to generate charge-separated states that preserve some of the photon energy as chemical potential. During the last three years, progress has been made on several fronts, all of which are related to the overall goal. A biomimetic system based on carotenoid-porphyrin-quinone triads has been constructed that demonstrates photoinduced transmembrane charge separation which in turn drives transmembrane proton transfer. Another investigation has focused on the use of proton transfer reactions to stabilize the initial products of photoinduced electron transfer and thereby increase the yield of long-lived charge separation. A third study has investigated the influence of rigid molecular geometries and short donor-acceptor separations on photoinduced electron transfer reactions. Finally, generation and quenching of singlet molecular oxygen by chlorophyll aggregates has been studied. All four studies are described and results are discussed.

  1. Nuclear structure theory. Annual technical progress report, July 1, 1975--September 30, 1976

    French, J.B.; Koltun, D.S.

    1976-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: Meson interactions with nucleons and nuclei, including elastic and inelastic scattering of pions, three-body theories of scattering and absorption of pions by deuterons, π-p bremsstrahlung, and multiple-excitation models for meson absorption by heavier nuclei. Studies of the inverse scattering problem including 1 S 0 nucleon-nucleon scattering; the relativistic two-body problem, particularly for relativistic effects at low energies: the unitary-pole expansion in nucleon-nucleon scattering with hard-core interactions. Statistical spectroscopy including: strength distributions and sum rules(both energy weighted and inverse energy weighted) for nuclear excitations; fluctuations and correlations in spectra, strengths and expectation values; studies of Garvey-Kelson and similar mass relationships; spectroscopy in huge spaces including spectral methods for renormalization of the interaction and for using (two + three)-body Skyrme interactions; technical aspects of operator averaging

  2. Power systems development facility. Quarterly technical progress report, January 1, 1994--March 31, 1994

    1994-07-01

    This quarterly technical progress report summarizes work completed during the last quarter of the Second Budget Period, January 1 through March 31, 1994, entitled {open_quotes}Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.{close_quotes} The objective of this project is to evaluate hot gas particulate control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scale-up of particulate control systems to commercial size.

  3. The U.S. nuclear waste management program - technical progress at Yucca Mountain

    Barrett, L.H. [U.S. Department of Energy (United States)

    2001-07-01

    This paper discusses the current status of a national program being developed by the U.S. Department of Energy for the management of spent nuclear fuel and high-level radioactive waste produced by civilian nuclear power generation and defense-related activities. In 1987 the U.S. Congress directed the Department to characterize the Yucca Mountain site in Nevada and determine its suitability for development of a geologic repository. This paper will focus on the technical progress that has been made after more than 15 years of scientific and engineering investigations at Yucca Mountain, and the remaining work that is being done to support a decision on whether to recommend the site for development of a geologic repository. (author)

  4. Progresso tecnico, forme di mercato e disoccupazione. ( Technical progress, market forms and unemployment

    A. ASIMAKOPULOS A.

    2013-12-01

    Full Text Available Lo scopo del presente lavoro è triplice . Il primo obiettivo è quello di sottolineare l'importanza delle intuizioni da trovare nel lavoro di Sylos Labini . Il secondo scopo è quello di espandere su di essa distinguendo tra i diversi tipi di progresso tecnico . Infine , il terzo obiettivo è quello di commentare il confronto di Labini di Ricardo e Keynes sulla possibilità di disoccupazione tecnologica . Per quanto riguarda la sua descrizione del progresso tecnologico come " risparmio di lavoro " , l'autore mostra che una descrizione più completa sarebbe più utile per i suoi scopiThe purpose of the present paper is threefold. The first purpose is to emphasise the importance of the insights to be found in Sylos Labini’s work. The second purpose is to expand upon it by distinguishing  between the different types of technical progress. Finally, the third purpose is to comment on Labini’s comparison of Ricardo and Keynes on the possibility of technological unemployment. Regarding his description of technological progress as “labour saving”, the author shows that a more comprehensive description would be more useful for his purposes.JEL: E24, J64, O33

  5. The effects of environmental regulation and technical progress on CO2 Kuznets curve: An evidence from China

    Yin, Jianhua; Zheng, Mingzheng; Chen, Jian

    2015-01-01

    Based on environmental Kuznets curve theory, a panel data model which takes environmental regulation and technical progress as its moderating factors was developed to analyse the institutional and technical factors that affect the path of low-carbon economic development. The results indicated that there was a CO 2 emission Kuznets curve seen in China. Environmental regulation had a significant moderating effect on the curve, and the inflection of CO 2 emissions could come substantially earlier under stricter environmental regulation. Meanwhile, the impact of technical progress on the low-carbon economic development path had a longer hysteresis effect but restrained CO 2 emission during its increasing stage and accelerated its downward trend during the decreasing stage which was conducive to emission reduction. Strict environmental regulation could force the high-carbon emitting industries to transfer from the eastern regions to the central or the western regions of China, which would make the CO 2 Kuznets curve higher in its increasing stage and lower in its decreasing stage than that under looser regulation. Furthermore, energy efficiency, energy structure, and industrial structure exerted a significant direct impact on CO 2 emissions; we should consider the above factors as essential in the quest for low-carbon economic development. - Highlights: • Estimate moderating effect of environmental regulation and technical progress on EKC. • There was a CO 2 emission Kuznets curve in effect in China. • Environmental regulation presents significant moderating effect on EKC. • Technical progress moderates the relationship between income and CO 2 emissions

  6. Study of mechanism of hydrogen diffusion in separation devices. Progress report for 1980-1983

    Lee, M.H.

    1983-01-01

    For the purpose of studying the mechanisms of hydrogen diffusion in separation devices e.g. transition-metal membranes, we have developed a microscopic dynamic model appropriate for describing the nonequilibrium statistical mechanics of hydrogen-in-a-metal. Using this model we have carried out a detailed analysis to obtain the autocorrelation function of density fluctuations in the model. Our model is built on the physical idea that, at low temperatures, spin clusters are the basic units or aggregates of transport. Our work can explain the reversed isotope effect in diffusion. We have also obtained an expression for the relative diffusivity, verifiable by experiments with tritium in metals. Our notion of spin clusters is novel. There is some evidence of their existence. The interstitial spin clusters are comparable to atomic and nuclear spin clusters, the only other natural spin clusters. Our demonstration of a long-time tail in the autocorrelation function is also novel. Diffusion can be anomalous if long time tails exist, a current topic in nonlinear behavior of fluids and solids. Our progress has been made possible by our development in the mathematical method of solving the generalized Langevin equation. This method is applicable to any time-dependent quantum many-body model. The underlying basis of this method is our discovery of a new orthogonalization process in Hilbert space, first since Gram and Schmidt over 100 years ago. Our process is simpler if Hilbert space is realized as is for all physical problems. To demonstrate the power and utility of our method we considered a well established model of metals, thereby discovering the existence of a low-frequency electronic mobility. This kind of intrinsic conductivity should exist in ensembles of all light particles, hence also relevant to hydrogen and its isotopes in metals

  7. Technical clarification to Silbert and Thomas (2013): "decisional separability, model identification, and statistical inference in the general recognition theory framework".

    Thomas, Robin D; Silbert, Noah H

    2014-04-01

    We offer a minor technical correction to the published proof of part (ii) of the main theorem in Silbert and Thomas (Psychonomic Bulletin & Review, 20, 1-20, 2013) that somewhat limits the scope of the equivalence observed in that work. Specifically, in order for a mean shift integrality with decisional separability to be mimicked by a perceptually separable but nondecisionally separable configuration, one needs to assume stimulus invariance. This holds when all of the covariance matrices in the stimulus configuration are equal to each other. We note that part (i) of the theorem is unaffected by this modification; an empirical finding of perceptual separability and the failure of decisional separability can be mimicked by a perceptually nonseparable, decisionally separable configuration without restricting the covariance matrices to be equal. We also note that stimulus invariance is often assumed in simple designs (e.g., Macmillan & Ornstein in Journal of the Acoustical Society of America, 97, 1261-1285, 1998), due to the implausibility of different perceptual correlations being present within stimuli perched very closely in perceptual space.

  8. Rapid instrumental and separation methods for monitoring radionuclides in food and environmental samples. Progress report

    Bhat, I.S.; Shukla, V.K.; Singh, A.N.; Nair, C.K.G.; Hingorani, S.B.; Dey, N.N.; Jha, S.K.; Rao, D.D.

    1995-01-01

    When activity levels are low, the direct gamma counting of milk and water samples take very long time, initial concentration step increases the sensitivity. 131 I in aqueous samples can be concentrated by absorption on AgCI in acidic condition. In case of milk, initial treatment with TCA, separation of precipitated casin and stirring the acidified (dil. HNO 3 ) clear solution with about 500 mg AgCI gives all the 131 I (more than 95%) picked up by AgCI which can be counted in a well crystal gamma spectrometer. In case of water samples acidification and direct stirring with AgCI all 131 I gets absorbed on to AgCI. About half an hour stirring has been found sufficient to give reproducible result. The total time required will be about 3 hrs. In case of 137 Cs, the aqueous solution should be stirred with ammonium phosphomolybdate (AMP) after acidification with HNO 3 . After an hour of AMP settling time, decantation, filtration and centrifuging one can get the AMP ready for counting in a gamma spectrometer having a well type detector. The analysis can be completed within 2 hrs. AgCI concentration of 131 I and AMP concentration of 137 Cs reduces the counting time significantly. These methods have been used for sea water and milk samples analysis. Methods are being standardised for solvent extraction separation of Pu, Am and Cm from preconcentrated environmental samples and direct counting of organic extract by liquid scintillation counting. For Pu determination, solvent extraction by TTA, back extraction and reextraction to 5% D2EHPA and direct liquid scintillation counting of Pu-alphas is planned. This will reduce the time required for Pu analysis to a significant extent. After bringing the sample to solution, this separation step can be carried out within 1 1/2 to 2 hrs. With Instagel scintillator cocktail in the packard 1550 LSS, Pu-239 counting had 70% efficiency with 5.3 cpm background. Pu-239 estimated in a few sediment sample gave results by both LSS method and Si

  9. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Introductory part and summaries

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan and comprises seven chapters. Chapter I briefly describes the importance of HLW management in promoting nuclear energy utilization. According to the long-term program, the HLW separated from spent fuels at reprocessing plants is to be vitrified and stored for a period of 30 to 50 years to allow cooling, then be disposed of in a deep geological formation. Chapter II mainly explains the concepts of geological disposal in Japan. Chapters III to V are devoted to discussions on three important technical elements (the geological environment of Japan, engineering technology and safety assessment of the geological disposal system) which are necessary for reliable realization of the geological disposal concept. Chapter VI demonstrates the technical ground for site selection and for setup of safety standards of the disposal. Chapter VII summarizes together with plans for future research and development. (Ohno, S.)

  10. Separate collection of plastic waste, better than technical sorting from municipal solid waste?

    Feil, Alexander; Pretz, Thomas; Jansen, Michael; Thoden van Velzen, Ulphard

    2017-01-01

    The politically preferred solution to fulfil legal recycling demands is often implementing separate collection systems. However, experience shows their limitations, particularly in urban centres with a high population density. In response to the European Union landfill directive, mechanical

  11. Fragment-separator at the U-400 cyclotron. (The Technical proposal)

    Majdikov, V.Z.; Bashevoj, V.V.

    1998-01-01

    The ion-optical calculations together with graphical modeling show some possibility to create the low-energy fragment-separator for the RIB experiments performed at the Coulomb barrier of interactions at the U-400 cyclotron. Combination of two available magnetic dipoles SP-95 and SP-97 without any additional focussing elements at the cyclotron switchyard permits one to obtain the parameters of the RIB separator adequate for the modern experiments performance

  12. Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

    Bender, W.

    2013-01-01

    Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

  13. Generation and focusing of pulsed intense ion beams. Technical progress report, 20 August 1981-30 September 1982

    Hammer, D.A.; Kusse, B.R.; Sudan, R.N.

    1983-07-01

    The progress on this contract is described in two parts. The first deals with the technical operation of the LION accelerator which is the exact equivalent to one line of PBFA-I. The second part is concerned with the experimental results on the ion diode mounted at the front end of the LION accelerator

  14. Impact of Environmental Regulation and Technical Progress on Industrial Carbon Productivity: An Approach Based on Proxy Measure

    Huan Zhang

    2016-08-01

    Full Text Available This research aims to study the main influencing factors of China’s industrial carbon productivity by incorporating environmental regulation and technical progress into an econometric model. The paper focuses on data from 35 of China’s industrial sectors and covers the period from 2006 to 2014, in order to examine the impact of environmental regulation and technical progress on carbon productivity. Methods applied include panel fixed effect model, panel random effect model and two stage least squares with instrumental variables (IV-2SLS. The effect of environmental regulation and technical progress has industrial heterogeneity. The paper subdivides industrial sectors into capital and technology intensive, resource intensive and labor intensive sectors according to factor intensiveness. The estimation results of the subgroups have uncovered that for capital and technology intensive and resource intensive sectors, environmental regulation has a more significant impact than technical progress; while for labor intensive sectors, innovation more significantly influences carbon productivity. In addition, foreign direct investment (FDI and industrialization level facilitate improving carbon productivity for the full sample. By contrast, industrial structure inhibits the overall industrial carbon productivity. The industry-specific results indicate that for capital and technology intensive sectors, optimizing of the industrial structure can improve carbon productivity; for resource intensive sectors, FDI and energy consumption structure should be emphasized more; for labor intensive sectors, industrialization levels help enhance carbon productivity. Finally the industrial sector-specific policy suggestions are proposed.

  15. Technical study on separating compounds of low level radioactive wastewater by composite membranes

    Kong Jinsong; Guo Weiqun

    2014-01-01

    In the view of low level radioactive wastewater from operation and decommissioning project for the nuclear facilities and technology of reverse osmosis, this paper analyzes the related research of reverse osmosis technology at home and aboard, and designs a technical system in practice by using reverse osmosis combined with a pretreatment process of disc filtration-ultrafiltration or filtration-microfiltration to treat radioactive wastewater. (authors)

  16. PFBC HGCU Test Facility. Technical progress report No. 24, Third quarter, CY 1995

    NONE

    1995-10-01

    This is the twenty-fourth and final Technical Progress Report submitted to the Department of Energy (DOE) in connection with the cooperative agreement between the DOE and Ohio Power Company for the Tidd PFBC Hot Gas Clean Up Test Facility. This report covers the work completed during the Third Quarter of CY 1995. All activity this quarter was directed toward the completion of the program final report. A draft copy of the final report was forwarded to DOE during this quarter, and DOE submitted their comments on the report to AEPSC. DOE requested that Westinghouse write an appendix to the report covering the performance of the fail-safe regenerator devices during Tad operation, and Westinghouse subsequently prepared the appendix. Additional DOE comments were incorporated into the report, and it will be issued in camera-ready form by the end of October, 1995, which is the program end date. Appendix 1 presents the results of filter candle posttest examination by Westinghouse performed on selected filter candles following final shutdown of the system.

  17. CROSSCUTTING TECHNOLOGY DEVELOPMENT AT THE CENTER FOR ADVANCED SEPARATION TECHNOLOGIES

    Christopher E. Hull

    2005-11-04

    This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

  18. Crosscutting Technology Development at the Center for Advanced Separation Technologies

    Christopher E. Hull

    2006-09-30

    This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

  19. CROSSCUTTING TECHNOLOGY DEVELOPMENT AT THE CENTER FOR ADVANCED SEPARATION TECHNOLOGIES

    Christopher E. Hull

    2006-05-15

    This Technical Progress Report describes progress made on the twenty nine subprojects awarded in the second year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

  20. Technical and economic aspects of oxygen separation for oxy-fuel purposes

    Chorowski Maciej

    2015-03-01

    Full Text Available Oxy combustion is the most promising technology for carbon dioxide, originated from thermal power plants, capture and storage. The oxygen in sufficient quantities can be separated from air in cryogenic installations. Even the state-of-art air separation units are characterized by high energy demands decreasing net efficiency of thermal power plant by at least 7%. This efficiency decrease can be mitigated by the use of waste nitrogen, e.g., as the medium for lignite drying. It is also possible to store energy in liquefied gases and recover it by liquid pressurization, warm-up to ambient temperature and expansion. Exergetic efficiency of the proposed energy accumulator may reach 85%.

  1. Technical possibilities to support separation of radioactive elements from metallic waste

    Bjoerkvall, Johan; Ye, Guozhu; Lindberg, Maria

    2014-01-01

    In the nuclear industry metallic objects can be either surface or bulk contaminated. Surface contaminated objects are often decontaminated by chemical or mechanical means, but are there other possibilities? During melting slags are formed either spontaneously or by adding slag forming compounds. However, one question that frequently arises is: Can all nuclides be separated by adding slag forming compounds? This question is not entirely correct as it is not only the radioactive nuclides that are separated from the metal but all atoms of that element present in the melt, radioactive and stable isotopes alike. Part of the answer lays in thermodynamics. Thermodynamics cannot positively answer the question with yes, as there are also practical and economical aspects to take into account, but if the answer is no there will never be any practical or economical efforts that will override nature. This paper will describe the theoretical baseline for evaluating the possibilities to separate certain elements during the melting process, mainly from steel but other metals will also touched on. The most common elements that have radioactive isotopes of interest is of course cobalt (Co-60, Co-58), but other elements of interest are manganese (Mn-54), strontium (Sr- 90), antimony (Sb-125) and of course heavy elements such as uranium, plutonium and americium. The paper will also describe methods used in the normal metal melting industry to separate elements from the base metal melted. This section will cover practical methods used as well as developed methods that are very seldom used due to time or financial constraints. (authors)

  2. INDEPENDENT TECHNICAL ASSESSMENT OF MANAGEMENT OF STORMWATER AND WASTEWATER AT THE SEPARATIONS PROCESS RESEARCH UNIT (SPRU) DISPOSITION PROJECT, NEW YORK

    Abitz, R.; Jackson, D.; Eddy-Dilek, C.

    2011-06-27

    The U.S. Department of Energy (DOE) is currently evaluating the water management procedures at the Separations Process Research Unit (SPRU). The facility has three issues related to water management that require technical assistance: (1) due to a excessive rainfall event in October, 2010, contaminated water collected in basements of G2 and H2 buildings. As a result of this event, the contractor has had to collect and dispose of water offsite; (2) The failure of a sump pump at a KAPL outfall resulted in a Notice of Violation issued by the New York State Department of Environment and Conservation (NYSDEC) and subsequent Consent Order. On-site water now requires treatment and off-site disposition; and (3) stormwater infiltration has resulted in Strontium-90 levels discharged to the storm drains that exceed NR standards. The contractor has indicated that water management at SPRU requires major staff resources (at least 50 persons). The purpose of this review is to determine if the contractor's technical approach warrants the large number of staff resources and to ensure that the technical approach is compliant and in accordance with federal, state and NR requirements.

  3. Nuclear structure theory: Technical progress report for period September 1, 1986-August 31, 1987

    French, J.B.; Koltun, D.S.

    1987-08-01

    This report summarizes progress in the following areas of research: (1) quark theory of nuclear matter, including further development of models in one-dimension with analytic solutions, numerical studies, bound properties, inclusion of spin and isospin degrees of freedom, excitation properties and response function; electron scattering, including application of sum rules to deeply inelastic scattering, and of quark models of nuclei; charge exchange in pion-nucleus reactions, including models of isotensor optical potential, optical theorem for double charge exchange, and coupled-channel calculations of single charge exchange; a unified theory of reaction dynamics and nuclear structure for intermediate energies, including diagrammatic formulation and development of appropriate computer programs; weak interactions: a study of the neutrino mass-matrix; bounds for time reversal noninvariance in the nucleon-nucleon interaction, obtained from spectral and strength fluctuations in complex nuclei, and separately from detailed balance in compound nuclear reactions. The relative sensitivities of the two methods are discussed; fluctuation measures for the two-dimensional harmonic oscillator; random matrices and symmetry-breaking in atomic spectra data; saturation effects for spectral measures in many-particle systems; and finally fluctuation-free statistical spectroscopy, applied to state densities and partition functions, including accurate absolute calculations of nuclear level spacings

  4. Power systems development facility. Quarterly technical progress report, July 1--September 30, 1993

    1993-12-31

    This quarterly technical progress report summarizes work completed during the Second Quarter of the Second Budget Period, July 1 through September 30, 1993, under the Department of Energy (DOE) Cooperative Agreement No. DE-FC21-90MC25140 entitled ``Hot Gas Cleanup Test Facility for Gasification and Pressurized Combustion.`` The objective of this project is to evaluate hot gas particle control technologies using coal-derived gas streams. This will entail the design, construction, installation, and use of a flexible test facility which can operate under realistic gasification and combustion conditions. The major particulate control device issues to be addressed include the integration of the particulate control devices into coal utilization systems, on-line cleaning techniques, chemical and thermal degradation of components, fatigue or structural failures, blinding, collection efficiency as a function of particle size, and scaleup of particulate control systems to commercial size. The conceptual design of the facility was extended to include a within scope, phased expansion of the existing Hot Gas Cleanup Test Facility Cooperative Agreement to also address systems integration issues of hot particulate removal in advanced coal-based power generation systems. This expansion included the consideration of the following modules at the test facility in addition to the existing Transport Reactor gas source and Hot Gas Cleanup Units: Carbonizer/Pressurized Circulating Fluidized Bed Gas Source. Hot Gas Cleanup Units to mate to all gas streams; Combustion Gas Turbine; and Fuel Cell and associated gas treatment. This expansion to the Hot Gas Cleanup Test Facility is herein referred to as the Power Systems Development Facility (PSDF). The major emphasis during this reporting period was continuing the detailed design of the facility.

  5. Instrumentation of dynamic gas pulse loading system. Technical progress report, first quarter 1992

    Mohaupt, H.

    1992-04-14

    The overall goal of this work is to further develop and field test a system of stimulating oil and gas wells, which increases the effective radius of the well bore so that more oil can flow into it, by recording pressure during the gas generation phase in real time so that fractures can be induced more predictably in the producing formation. Task 1: Complete the laboratory studies currently underway with the prototype model of the instrumentation currently being studied. Task 2: Perform field tests of the model in the Taft/Bakersfield area, utilizing operations closest to the engineers working on the project, and optimize the unit for various conditions encountered there. Task 3: Perform field test of the model in DGPL jobs which are scheduled in the mid-continent area, and optimize the unit for downhole conditions encountered there. Task 4: Analyze and summarize the results achieved during the complete test series, documenting the steps for usage of downhole instrumentation in the field, and compile data specifying use of the technology by others. Task 5: Prepare final report for DOE, and include also a report on the field tests completed. Describe and estimate the probability of the technology being commercialized and in what time span. The project has made substantial technical progress, though we are running about a month behind schedule. Expenditures are in line with the schedule. Increased widespread interest in the use of DGPL stimulation has kept us very busy. The computer modeling and test instrumentation developed under this program is already being applied to commercial operations.

  6. Recent progress in molecular simulation of nanoporous graphene membranes for gas separation

    Fatemi, S. Mahmood; Baniasadi, Aminreza; Moradi, Mahrokh

    2017-07-01

    If an ideal membrane for gas separation is to be obtained, the following three characteristics should be considered: the membrane should be as thin as possible, be mechanically robust, and have welldefined pore sizes. These features will maximize its solvent flux, preserve it from fracture, and guarantee its selectivity. Graphene is made up of a hexagonal honeycomb lattice of carbon atoms with sp 2 hybridization state forming a one-atom-thick sheet of graphite. Following conversion of the honeycomb lattices into nanopores with a specific geometry and size, a nanoporous graphene membrane that offers high efficiency as a separation membrane because of the ultrafast molecular permeation rate as a result of its one-atom thickness is obtained. Applications of nanoporous graphene membranes for gas separation have been receiving remarkably increasing attention because nanoporous graphene membranes show promising results in this area. This review focuses on the recent advances in nanoporous graphene membranes for applications in gas separation, with a major emphasis on theoretical works. The attractive properties of nanoporous graphene membranes introduce make them appropriate candidates for gas separation and gas molecular-sieving processes in nanoscale dimensions.

  7. Uranium isotope separation in the solid state. Progress report, December 1, 1976--June 1, 1977

    Bernstein, E.R.

    1977-06-01

    Since we were actively able to work on this project, we have been engaged in three separate lines of research. Each of these has been related to laser-induced isotope separation of uranium in the solid state. The three areas are: (a) improved reaction chemistry for both host materials Zr(BH 4 ) 4 and Hf(BH 4 ) 4 and U(BH 4 ) 4 itself; (b) improved spectroscopic techniques in order to obtain sharper spectra; and (c) solid state photochemical investigations to study U(BH 4 ) 4 photodecomposition mechanism and yield as a function of wave length. These are all integral parts of the solid state isotope separation procedure and are discussed in terms of the overall process proposed

  8. Feasibility studies on macroscopic separation of carbon isotopes by IR laser chemistry - a technical report

    Mathi, P.; Nayak, A.K.; Parthasarathy, V.; Abhinandan, L.; Sarkar, S.K.

    2007-11-01

    This report describes the feasibility studies for macroscopic separation of carbon isotopes (∼ 50% enrichment level) by infrared multiphoton dissociation (IRMPD) of Freon - 22 (CF 2 HCl) using a 10Hz pulsed carbon dioxide laser in a large volume (∼ 300 litre) photochemical reactor (PCR). After a general introduction to the objective, the importance of characterization studies with a 10 Hz CO 2 laser is brought out before large scale operation in the PCR is carried out. The laboratory scale results obtained in a small cell with a lower average power (0.5 W) CO 2 laser is verified with a higher power (10 W) laser under optimal conditions. Such an exercise helps in understanding of any anomalies of the results and for applying the appropriate corrective measures while scaling up. The report deals with the design details, fabrication, installation and commissioning of the major components of the setup namely laser system, photochemical reactor, low temperature distillation unit and preparative gas chromatograph for realizing the targeted task. It further describes the standardization methodology of a sensitive analytical technique using quadrupole mass spectrometry (QMS) to ascertain the C 2 F 4 product quality (i.e. enrichment). A pre- concentration method for separating C 2 F 4 from CF 2 HCl using gas chromatography has been developed for very low-level mass spectral analysis. During this exercise, an indigenous QMS developed in VPID (erstwhile MS and ES) has also been benchmarked by comparing its performance with a commercial QMS unit. The report gives in details the operational experience of carrying out the large scale enrichment task in a batch process. The modular PCR employing a multi-pass refocusing Herriott optics for efficient photon utilization and gas blower arrangement for gas circulation during laser photolysis has given a typical production rate of about 10 mg/hr for total carbon with a 13 C isotopic purity of ∼ 40%. It further indicates the scope

  9. Progress in 15N and 13C separation by isotopic exchange

    Axente, D.

    2004-01-01

    An experimental study of 15 N separation by isotopic exchange in NO, NO 2 - HNO 3 system under pressure is presented. The pressure increase in 15 N separation plant improved the isotopic transport between the two phases circulated in counter-current in the packed column according to a better kinetics of isotopic exchange at higher pressures. The operation of 15 N separation plant at a pressure of 1.8 atm (absolute) will permit doubling of 10 M nitric acid flow rate and of 15 N production of a given column. The improved performance at a higher pressure is significant for large scale 15 N production, which would be utilized for uranium nitride fuels for FBRs. Enrichment of 13 C by chemical exchange between CO 2 and amine carbamate in nonaqueous solvent has been modelled. For process optimization the steady state separation and the height equivalent to a theoretical plate (HETP) have been determined for different experimental conditions and simulated for higher pressures than atmospheric one. At lower temperature (5 deg C) as the pressure increases the quantity of CO 2 dissolved in amine solution increases. For process analysis at higher pressures and lower temperatures, the two steps model has been considered. At 0.9 MPa pressure and 5 deg C the reaction rate is higher than at 25 deg C and atmospheric pressure, the value of HETP being lower with more than 100% than at 25 deg C. (author)

  10. Decomposing productivity growth allowing efficiency gains and price-induced technical progress

    Oude Lansink, A.G.J.M.; Silva, E.; Stefanou, S.

    2000-01-01

    Time- and firm-specific output technical efficiency measures are generated within a price-induced technological change framework. The firm-specific production frontier incorporates past prices as an argument encouraging innovation and a time trend to account for exogenous technical change. The

  11. Nuclear Physics Laboratory, University of Colorado technical progress report, 1976 and proposal for continuation of contract

    1976-01-01

    This report summarizes the work carried out at the Nuclear Physics Laboratory of the University of Colorado during the period November 1, 1975 to November 1, 1976. The low energy nuclear physics section is dominated by light-ion reaction studies which span a wide range. These include both two-neutron and two-proton transfer reactions, charge exchange and inelastic scattering, as well as single nucleon transfer reactions. The nuclei studied vary widely in their mass and characteristics. These reaction studies have been aided by the multi-use scattering chamber which now allows the energy-loss-spectrometer beam preparation system (beam swinger) to shift from charged particle studies to neutron time-of-flight studies with a minimum loss of time. The intermediate energy section reflects the increase in activity accompanying the arrival of LAMPF data and the initiation of (p,d) studies at the Indiana separated-sector cyclotron. The nucleon removal results provided by the π beam at EPICS previous to completion of the spectrometer have shown that nuclear effects dominate this process, so that the widely used free interaction picture is inadequate. The section entitled ''Other Activities'' reveals continuing activities in new applications of nuclear techniques to problems in medicine and biology. Reactions important to astrophysics continue to be investigated and our trace-element program remains at a high level of activity. The theoretical section reports new progress in understanding magnitudes of two-step reactions by inclusion of finite-range effects. A new finite-range program which is fast and economical has been completed. Intermediate energy results include calculations of π-γ angular correlations, low energy π-nucleus interactions, as well as (p,d) and nucleon scattering calculations for intermediate energies

  12. Recovery Act: Alpena Biorefinery and Alpena Biorefinery Lignin Separation Final Technical Report

    Retsina, Theodora [American Process Inc., Atlanta, GA (United States)

    2016-12-19

    The Alpena Biorefinery (AB) was constructed in Alpena, Michigan, at the Decorative Panels International hardboard manufacturing facility. The goal of the AB was to demonstrate a modular, technically successful, and financially viable process of making cellulosic ethanol from woody biomass extract at wood processing facilities. At full capacity, the AB can produce 894,200 gallons per year of cellulosic ethanol and 696,000 gallons per year of aqueous potassium acetate, using extract from northern hardwood and aspen woodchips feedstock. The project objectives and the value proposition of AB promote the national goals of energy independence, greenhouse gas reduction, and green job creation and retention. A successful outcome of the Alpena Biorefinery project has been commercial sales of the first ever cellulosic ethanol RINS generated from woody biomass in the US, under the EPA’s Renewable Fuels Standard Program. We believe that American Process is also likely the first company in the world to produce commercial quantities of cellulosic ethanol from mixed forest residue. Life Cycle Analysis performed by Michigan Institute of Technology found that the entire life cycle greenhouse gas emissions from the plant’s cellulosic ethanol were only 25 percent that of petroleum-based gasoline. They found the potassium acetate runway de-icer coproduct generates up to 45 percent less greenhouse gases than the production of conventional potassium acetate. The Alpena Biorefinery project created 31 permanent jobs for direct employees and helped retain 200 jobs associated with the existing Decorative Panels International facility, by increasing its economic viability through significant savings in waste water treatment costs. The AB project has been declared a Michigan Center of Energy Excellence and was awarded a $4 million State of Michigan grant. The project also received New Market Tax Credit financing for locating in an economically distressed community. All other equity funds

  13. Separate collection of MSW. Technical and economical survey; Evoluzione e mercato della ricerca differenziata. Aspetti tecnici ed economici

    Riganti, V. [Pavia Univ., Pavia (Italy). Dipt. di Chimica Generale, Cattedra di Chimica Merceologica; Vaccari, V. [Pavia Univ., Pavia (Italy). Dipt. di Ricerche Aziendali, Cattedra di Tecnologia dei Cicli Produttivi; Miranda, S. [CISPEL Lombardia, Segreteria Tecnica del Gruppo di Lavoro Ambiente, Milan (Italy)

    2000-01-01

    In this work the increasing of the separate collection of MSW (Municipal Solid Wastes) in Italy, has been studied, in terms of environmental improving, materials recycling and energy recovery, developing the concerning technical and economical aspects. The national situation has been evaluated too, on the basis of a statistical approach, carried out using data from reports of: CRS-Pro Acqua, ANPA, Federambiente. [Italian] Lo sviluppo della raccolta differenziata in Italia viene delineato in funzione della tutela ambientale e del recupero di materie e di energia, sviluppandone gli aspetti tecnici ed economici. Viene altresi' presentato un quadro statistico delle raccolte differenziate sulla base di elaborazioni da varie fonti (CRS-Pro Acqua, ANPA, Federambiente).

  14. Hydrogen production by supercritical water gasification of biomass. Phase 1 -- Technical and business feasibility study, technical progress report

    NONE

    1997-12-01

    The nine-month Phase 1 feasibility study was directed toward the application of supercritical water gasification (SCWG) for the economical production and end use of hydrogen from renewable energy sources such as sewage sludge, pulp waste, agricultural wastes, and ultimately the combustible portion of municipal solid waste. Unique in comparison to other gasifier systems, the properties of supercritical water (SCW) are ideal for processing biowastes with high moisture content or contain toxic or hazardous contaminants. During Phase I, an end-to-end SCWG system was evaluated. A range of process options was initially considered for each of the key subsystems. This was followed by tests of sewage sludge feed preparation, pumping and gasification in the SCW pilot plant facility. Based on the initial process review and successful pilot-scale testing, engineering evaluations were performed that defined a baseline system for the production, storage and end use of hydrogen. The results compare favorably with alternative biomass gasifiers currently being developed. The results were then discussed with regional wastewater treatment facility operators to gain their perspective on the proposed commercial SCWG systems and to help define the potential market. Finally, the technical and business plans were developed based on perceived market needs and the projected capital and operating costs of SCWG units. The result is a three-year plan for further development, culminating in a follow-on demonstration test of a 5 MT/day system at a local wastewater treatment plant.

  15. Coal to SNG: Technical progress, modeling and system optimization through exergy analysis

    Li, Sheng; Ji, Xiaozhou; Zhang, Xiaosong; Gao, Lin; Jin, Hongguang

    2014-01-01

    Highlights: • Technical progresses of coal to SNG technologies are reported. • The entire coal to SNG system is modeled. • Coupling between SNG production and power generation is investigated. • Breakthrough points for further energy saving are determined. • System performance is optimized based on the first and second laws of thermodynamics. - Abstract: For both energy security and CO 2 emission reduction, synthetic natural gas (SNG) production from coal is an important path to implement clean coal technologies in China. In this paper, an overview of the progress of coal to SNG technologies, including the development of catalysts, reactor designs, synthesis processes, and systems integration, is provided. The coal to SNG system is modeled, the coupling between SNG production and power generation is investigated, the breakthrough points for further energy savings are determined, and the system performance is optimized based on the first and the second laws of thermodynamics. From the viewpoint of the first law of thermodynamics, the energy conversion efficiency of coal to SNG system can reach 59.8%. To reduce the plant auxiliary power, the breakthrough points are the development of low-energy-consumption oxygen production technology and gas purification technology or seeking new oxidants for coal gasification instead of oxygen. From the viewpoint of the second law of thermodynamics, the major exergy destruction in a coal to SNG system occurs in the coal gasification unit, SNG synthesis unit and the raw syngas cooling process. How to reduce the exergy destruction in these units is the key to energy savings and system performance enhancement. The conversion ratio of the first SNG synthesis reactor and the split ratio of the recycle gas are key factors that determine the performance of both the SNG synthesis process and the whole plant. A “turning point” phenomenon is observed: when the split ratio is higher than 0.90, the exergy destruction of the SNG

  16. Separation Science and Technology. Semiannual progress report, April 1993--September 1993

    Vandegrift, G.F.; Chamberlain, D.B.; Conner, C.

    1996-01-01

    This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1993. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Other projects are underway with the objective of developing (1) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process, (2) treatment schemes for liquid wastes stored or being generated at Argonne, (3) a process based on sorbing modified TRUEX solvent on magnetic beads to be used for separation of contaminants from radioactive and hazardous waste streams, and (4) a process that uses low-enriched uranium targets for production of 99 Mo for nuclear medicine uses

  17. Progress in Separation of Gases by Permeation and Liquids by Pervaporation Using Ionic Liquids: A Review

    Kárászová, M. (Magda); Kačírková, M. (Marie); Friess, K.; Izák, P. (Pavel)

    2014-01-01

    The effective separation of gases and liquids by membranes containing ionic liquids actually belongs to one of the challenging topics in membrane community. During last decade, a plenty of new kinds of ionic liquids (IL), their combinations, different types of polymerized ionic liquids and polymer–IL composite membranes were developed and tested. This review summarizes the most important achievements and findings connected with the ionic liquid based membranes research and tries to answer h...

  18. Fundamental chemistry, characterization, and separation of technetium complexes in Hanford waste. 1998 annual progress report

    Ashley, K.R.; Blanchard, D.L. Jr.; Schroeder, N.C.

    1998-01-01

    'The ultimate goal of this proposal is to separate technetium from Hanford tank waste. The recent work has shown that a large portion of the technetium is not pertechnetate (TcO 4 - ) and is not easily oxidized. This has serious repercussions for technetium partitioning schemes because they are designed to separate this chemical form. Rational attempts to oxidize these species to TcO 4 - for processing or to separate the non-pertechnetate species themselves would be facilitated by knowing the identity of these complexes and understanding their fundamental chemistry. Tank characterization work has not yet identified any of the non-pertechnetate species. However, based on the types of ligands available and the redox conditions in the tank, a reasonable speculation can be made about the types of species that may be present. Thus, this proposal will synthesize and characterize the relevant model complexes of Tc(III), Tc(IV), and Tc(V) that may have formed under tank waste conditions. Once synthesized, these complexes will be used as standards for developing and characterizing the non-pertechnetate species in actual waste using instrumental techniques such as capillary electrophoresis electrospray mass spectrometry (CE-MS), x-ray absorbance spectroscopy (EXAFS and XANES), and multi-nuclear NMR (including 99 Tc NMR). The authors study the redox chemistry of the technetium complexes so that more efficient and selective oxidative methods can be used to bring these species to TcO 4 - for processing purposes. They will also study their ligand substitution chemistry which could be used to develop separation methods for non-pertechnetate species. Understanding the fundamental chemistry of these technetium complexes will enable technetium to be efficiently removed from the Hanford tank waste and help DOE to fulfill its remediation mission. This report summarizes the first 8 months of a 3-year project.'

  19. Progress in Separation of Gases by Permeation and Liquids by Pervaporation Using Ionic Liquids: A Review

    Kárászová, Magda; Kačírková, Marie; Friess, K.; Izák, Pavel

    2014-01-01

    Roč. 132, AUG 20 (2014), s. 93-101 ISSN 1383-5866 R&D Projects: GA ČR GA14-12695S; GA ČR GAP106/10/1194; GA MŠk LH14006; GA MŠk(CZ) LD14094 Institutional support: RVO:67985858 Keywords : gas separations * ionic liquid * supported ionic liquid membranes Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.091, year: 2014

  20. Recent Progress in Asymmetric Catalysis and Chromatographic Separation by Chiral Metal–Organic Frameworks

    Suchandra Bhattacharjee

    2018-03-01

    Full Text Available Metal–organic frameworks (MOFs, as a new class of porous solid materials, have emerged and their study has established itself very quickly into a productive research field. This short review recaps the recent advancement of chiral MOFs. Here, we present simple, well-ordered instances to classify the mode of synthesis of chiral MOFs, and later demonstrate the potential applications of chiral MOFs in heterogeneous asymmetric catalysis and enantioselective separation. The asymmetric catalysis sections are subdivided based on the types of reactions that have been successfully carried out recently by chiral MOFs. In the part on enantioselective separation, we present the potentiality of chiral MOFs as a stationary phase for high-performance liquid chromatography (HPLC and high-resolution gas chromatography (GC by considering fruitful examples from current research work. We anticipate that this review will provide interest to researchers to design new homochiral MOFs with even greater complexity and effort to execute their potential functions in several fields, such as asymmetric catalysis, enantiomer separation, and chiral recognition.

  1. A Simple extension of Dematerialization Theory: Incorporation of Technical Progress and the Rebound Effect

    Magee, Christopher L.; Devezas, Tessaleno C.

    2016-01-01

    Dematerialization is the reduction in the quantity of materials needed to produce something useful over time. Dematerialization fundamentally derives from ongoing increases in technical performance but it can be counteracted by demand rebound - increases in usage because of increased value (or decreased cost) that also results from increasing technical performance. A major question then is to what extent technological performance improvement can offset and is offsetting continuously increasin...

  2. Separation Science and Technology. Semiannual progress report, April 1993--September 1993

    Vandegrift, G.F.; Chamberlain, D.B.; Conner, C. [and others

    1996-01-01

    This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1993. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Other projects are underway with the objective of developing (1) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process, (2) treatment schemes for liquid wastes stored or being generated at Argonne, (3) a process based on sorbing modified TRUEX solvent on magnetic beads to be used for separation of contaminants from radioactive and hazardous waste streams, and (4) a process that uses low-enriched uranium targets for production of {sup 99}Mo for nuclear medicine uses.

  3. Separation science and technology. Semiannual progress report, October 1993 - March 1994

    Vandegrift, G.F.; Aase, S.B.; Buchholz, B.

    1997-12-01

    This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory (ANL), in the period October 1993-March 1994. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Other projects are underway with the objective of developing (1) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process, (2) treatment schemes for liquid wastes stored are being generated at ANL, (3) a process based on sorbing modified TRUEX solvent on magnetic beads to be used for separation of contaminants from radioactive and hazardous waste streams, and (4) a process that uses low-enriched uranium targets for production of 99 Mo for nuclear medicine uses

  4. The Impacts of Technical Progress on Sulfur Dioxide Kuznets Curve in China: A Spatial Panel Data Approach

    Zhimin Zhou

    2017-04-01

    Full Text Available This paper aims to reveal the nexus for sulfur dioxide (SO2 emission and income, as well as the effects of technical progress on SO2 emission in China based on environment Kuznets curve (EKC hypothesis. The spatial panel technique is used in case the coefficient estimates are biased due to the negligence of spatial dependence. With the provincial panel data of China from 2004 to 2014, this is the first research that finds an inverse N-trajectory of the relationship between SO2 emission and economic growth and confirms the beneficial impacts of technical advancement on SO2 emission abatement. The empirical results also suggest that the industrial structure change is an important driving force of the SO2 EKC. In addition, the direct and spillover effects of determinants on sulfur emission are clarified and estimated by a correct approach. Finally, we check the stability of our conclusions on the EKC shape for SO2 and technical progress effects when controlling for different variables and specifications, through which we find the turning points are sensitive to variables selections.

  5. Savannah River Ecology Laboratory, Annual Technical Progress Report of Ecological Research, June 30, 2002

    Paul M. Bertsch, (Director)

    2002-06-30

    The Savannah River Ecology Laboratory (SREL) is a research unit of The University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) near Aiken, South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE). The Laboratory's research mission during the 2002 fiscal year was fulfilled with the publication of 76 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 50 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members, staff, and graduate students received awards. These are described in the section titled Special Accomplishments of Faculty, Staff, Students, and Administration on page 51. Notable scientific accomplishments include work conducted on contaminant transport, stable isotopes, sandhills ecology, and phytoremediation: (1) A collaborative study between Dr. Tom Hinton at SREL and scientists at SRTC demonstrated the feasibility of using illite clay to sequester 137Cs in sediments along the P and R reactor cooling canal system, where approximately 3,000 acres of land are contaminated. Overall, the study showed significant decreases in cesium concentrations and bioavailability following the addition of illite with no sign of harm to the ecosystem. While the cesium remains sequestered from the biosphere, its radioactivity decays and the process progresses from contaminant immobilization to remediation. (2) SREL's stable isotope laboratory is now fully functional. Stable isotope distributions in nature can provide important insights into many historical and current environmental processes. Dr. Christopher Romanek is leading SREL's research

  6. High-Efficiency Nitride-Based Solid-State Lighting. Final Technical Progress Report

    Paul T. Fini; Shuji Nakamura

    2005-01-01

    In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 (micro)m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of ∼ 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light emitting diodes, and packaging them to produce a white light

  7. Savannah River Ecology Laboratory, Annual Technical Progress Report of Ecological Research, June 30, 2002

    Paul M. Bertsch,

    2002-01-01

    The Savannah River Ecology Laboratory (SREL) is a research unit of The University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) near Aiken, South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE). The Laboratory's research mission during the 2002 fiscal year was fulfilled with the publication of 76 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 50 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members, staff, and graduate students received awards. These are described in the section titled Special Accomplishments of Faculty, Staff, Students, and Administration on page 51. Notable scientific accomplishments include work conducted on contaminant transport, stable isotopes, sandhills ecology, and phytoremediation: (1) A collaborative study between Dr. Tom Hinton at SREL and scientists at SRTC demonstrated the feasibility of using illite clay to sequester 137Cs in sediments along the P and R reactor cooling canal system, where approximately 3, 000 acres of land are contaminated. Overall, the study showed significant decreases in cesium concentrations and bioavailability following the addition of illite with no sign of harm to the ecosystem. While the cesium remains sequestered from the biosphere, its radioactivity decays and the process progresses from contaminant immobilization to remediation. (2) SREL's stable isotope laboratory is now fully functional. Stable isotope distributions in nature can provide important insights into many historical and current environmental processes. Dr. Christopher Romanek is leading SREL's research in this area

  8. Separations Science and Technology, Semiannual progress report, October 1991--March 1992

    Vandegrift, G.F.; Betts, S.; Chamberlain, D.B.

    1994-01-01

    This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period October 1991--March 1992. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Two other projects are underway with the objective of developing (1) a membrane-assisted solvent extraction method for treating natural and process waters contaminated by volatile organic compounds and (2) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process

  9. Separation science and technology. Semiannual progress report, April 1992--September 1992

    Vandegrift, G.F.; Betts, S.; Bowers, D.L.

    1994-09-01

    This document reports on the work done by the Separations Science and Technology Programs of the Chemical Technology Division, Argonne National Laboratory, in the period April-September 1992. This effort is mainly concerned with developing the TRUEX process for removing and concentrating actinides from acidic waste streams contaminated with transuranic (TRU) elements. The objectives of TRUEX processing are to recover valuable TRU elements and to lower disposal costs for the nonTRU waste product of the process. Two other projects are underway with the objective of developing (1) a membrane-assisted solvent extraction method for treating natural and process waters contaminated by volatile organic compounds and (2) evaporation technology for concentrating radioactive waste and product streams such as those generated by the TRUEX process

  10. Theoretical particle physics. Technical progress report, May 1, 1985-April 30, 1986

    Gottlieb, S.A.; Hendry, A.W.; Kostelecky, V.A.; Lichtenberg, D.B.

    1986-05-01

    Research activities during this past year included theoretical work in lattice gauge theory, EMC effect, supersymmetry and supergravity, weak interactions including CP violation, and superstrings. Progress in all these areas is reported

  11. Symbol manipulation by computer applied to plasma physics. Technical progress report 2

    Rosen, B.

    1977-09-01

    Progress has been made in automating the calculation of parametric processes analytically by computer. The computations are performed automatically to lowest order quickly and efficiently. Work has started on a method for solving the nonlinear differential equations describing interacting modes

  12. University of Florida, University research program in robotics. Annual technical progress report

    Crane, C.D. III; Tulenko, J.S.

    1994-05-01

    Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development

  13. Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1, 1997--July 31, 1997

    NONE

    1997-09-01

    Progress summaries are provided from the Amarillo National Center for Plutonium. Programs include the plutonium information resource center, environment, public health, and safety, education and training, nuclear and other material studies.

  14. Research in elementary particle physics. Technical progress report, June 1, 1983-May 31, 1984

    Kirsch, L.E.; Schnitzer, H.J.; Bensinger, J.R.; Abbott, L.F.

    1984-01-01

    Under this contract, research has been performed on both the theoretical and experimental properties of elementary particles. A brief description of the work which is either in progress or has been completed is given. Publications are listed

  15. Research in elementary particle physics: Technical progress report, June 1, 1987-May 31, 1988

    Kirsch, L.E.; Schnitzer, H.J.; Abbott, L.F.; Bensinger, J.R.; Blocker, C.A.

    1988-01-01

    The main topics discussed in the progress report: electron/photon algorithm groups; W and Z analysis; heavy quark analysis; gas gain monitoring; database upgrade; CDF test beam studies; string theory; cosmology; and neutral networks

  16. University of Florida, University research program in robotics. Annual technical progress report

    Crane, C.D. III; Tulenko, J.S.

    1994-05-01

    Progress is reported in the areas of environmental hardening, database, world modeling, vision, man-machine interface, advanced liquid metal reactor inspection robot, and articulated transporter/manipulator system (ATMS) development.

  17. Technical progress report for the quarter 1 October-31 December 1980

    1981-01-01

    This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management

  18. Atmospheric Effects of Nuclear Energy Centers (AENEC) Program. Annual technical progress report, July 1975--September 1976

    Patrinos, A.A.; Hoffman, H.W.

    1977-04-01

    The Technical Memorandum contains information of a preliminary nature from the six participants of the Program describing their activities and presenting the results obtained during the reporting period. The birth of the Program, its definition and evolution are described, and a complete breakdown of responsibilities and tasks assigned to the six AENEC participants is presented

  19. The Michigan high-level radioactive waste program: Final technical progress report

    1987-01-01

    This report comprises the state of Michigan's final technical report on the location of a proposed high-level radioactive waste disposal site. Included are a list of Michigan's efforts to review the DOE proposal and a detailed report on the application of geographic information systems analysis techniques to the review process

  20. Developing Technical Writing Skills in the Physical Chemistry Laboratory: A Progressive Approach Employing Peer Review

    Gragson, Derek E.; Hagen, John P.

    2010-01-01

    Writing formal "journal-style" lab reports is often one of the requirements chemistry and biochemistry students encounter in the physical chemistry laboratory. Helping students improve their technical writing skills is the primary reason this type of writing is a requirement in the physical chemistry laboratory. Developing these skills is an…

  1. Technical progress report for the quarter 1 October-31 December 1980

    1981-01-01

    This report describes the technical accomplishments on the commercial nuclear waste management programs and on the geologic disposal of nuclear wastes. The program is organized into eight tasks: systems, waste package, site, repository, regulatory and institutional, test facilities and excavations, land acquisition, and program management. (DLC)

  2. On the accuracy of X-ray lithography using synchrotron radiation for the fabrication of technical separation nozzle elements

    Becker, E.W.; Ehrfeld, W.; Muenchmeyer, D.

    1984-04-01

    As a method for the fabrication of technical separation nozzle elements with extremely small characteristic dimensions, the Institut fuer Kernverfahrenstechnik of the University and the Nuclear Research Centre of Karlsruhe in co-operation with the Siemens AG, Munich, and the Fraunhofer Institute for Solid-State Technology, Munich, are developping the LIGA-process. In this process, poly(methylmethacrylate) layers of an approximate thickness of 0.5 mm are structured by means of X-ray depth-lithography using synchrotron radiation. Subsequently, the nozzle structures are electroformed with nickel using the PMMA-layers as a mould. The manufacturing precision which can be obtained by X-ray depth-lithography was investigated by means of computer simulation of both the irradiation and the development step. In the first step the precision is limited by diffraction, photoelectrons, and beam divergency, respectively. It is shown, that under appropriate conditions each of these effects contributes only some 0.1 μm to errors at the structure edges. The simulation of the development step is based on experiments on the dissolution properties of both irradiated and unirradiated PMMA in a special developing agent. From the results of the computer simulation it can be seen, that the ratio of the slit length to the smallest width which is required for the fabrication of separation nozzles and the required precision are already obtainable in the one-step lithographic process at a characteristic wavelength of 0.2 nm. If an extreme structure height in combination with high precision is required or if a radiation source with a longer characteristic wavelength has to be used, the multi-step process can be applied. The calculations may easily be adapted to different manufacturing parameters concerning the radiation source or the developer characteristic. (orig.) [de

  3. GT-MHR COMMERCIALZATION STUDY. TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD MAY 1 THROUGH MAY 31, 2003

    SHENOY, A.S.

    2003-01-01

    A271 GT-MHR COMMERCIALZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD MAY 1 THROUGH MAY 31, 2003. Petten advised GA the start of the HFR-EU2 irradiation is being delayed until late July 2004. HFR-EU1 (pebble fuel) is also delayed until February/March 2004. The reason for the delays was implementation of new financial regulations at Petten that delayed the contracts for capsule fabrication. Review of the MHR-2 Fuel Product Specification was completed. Revision of the specification to incorporate the review results is in progress. Detailed test matrices have been drafted for capsule irradiation tests and for post-irradiation heating tests proposed for development and qualification of advanced coated-particle fuels capable of meeting anticipated VHTR fuel performance requirements

  4. Association Euratom - Risø National Laboratory, Technical University of Denmark - Annual Progress Report 2007

    Michelsen, Poul; Korsholm, Søren Bang; Juul Rasmussen, Jens

    The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the pla......The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction...... phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007....

  5. Optically pumped polarized 23Na vapor target for use in polarized ion source. Technical progress report

    Anderson, L.W.

    1984-01-01

    We are currently measuring relaxation times in an optically pumped 23 Na vapor target. Our research is directed toward improvements in the optically pumped Na vapor targets used for the production of polarized H - ions. In this progress report we review the properties of the optically pumped polarized H - ion source and especially the optically pumped Na vapor target employed in this source as well as discussing the progress of our research on relaxation times in an optically pumped Na vapor target. 30 references, 6 figures, 3 tables

  6. Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

    Kinney, Edward R. [University of Colorado, Boulder, CO

    2014-09-12

    This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

  7. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2011

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark (until 31-12- 2011: Association Euratom – Risø DTU) covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport...... temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2011....

  8. Microwave plasma source for neutral-beam injection systems. Quarterly technical progress report

    1981-01-01

    The overall program is described and the technical and programmatic reasons for the decision to pursue both the RFI and ECH sources into the current hydrogen test stage is discussed. We consider the general characteristics of plasma sources in the parameter regime of interest for neutral beam applications. The operatonal characteristics, advantages and potential problems of RFI and ECH sources are discussed. In these latter two sections we rely heavily on experience derived from developing RFI and ECH ion engine sources for NASA

  9. Index to Nuclear Safety: a technical progress review by chrology, permuted title, and author, Volume 11(1) through Volume 20(6)

    Cottrell, W B; Passiakos, M

    1980-06-01

    This index to Nuclear Safety, a bimonthly technical progress review, covers articles published in Nuclear Safety, Volume II, No. 1 (January-February 1970), through Volume 20, No. 6 (November-December 1979). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 600 technical articles published in Nuclear Safety in the last ten years are listed in this index.

  10. Accelerator research studies. Technical progress report, July 1, 1985-June 30, 1986

    1986-01-01

    Progress is reported in these areas: study of instabilities and emittance growth in periodic focusing systems for intense beams; study of collective ion acceleration by intense electron beams and pulse powered plasma focus; and study of microwave sources and parameter scaling for high-frequency linacs

  11. Experimental studies of elementary particle interactions at high energies: Technical progress report

    1987-01-01

    This paper discusses progress of experiments at CERN and Fermilab. At CERN, data accumulation and analysis is discussed for the UA-6 experiment, which involves proton-antiproton collisions. At Fermilab, the testing of a collider detector for the Tevatron is discussed

  12. Accelerator research studies: Technical progress report, June 1, 1988--May 31, 1989

    1989-01-01

    This report discusses research progress in the following general topics: Study of transport and longitudinal compression of intense, high-brightness beams; study of collective ion acceleration by intense electron beams and pulse powered plasma focus; and study of microwave sources and parameter scaling for high-frequency electron-positron supercollider linacs

  13. High beta and second stability region transport and stability analysis: Technical progress report

    Hughes, M.H.; Phillips, M.W.

    1995-03-01

    This report summarizes MHD equilibrium and stability studies carried out at Northrop Grumman's Advanced Technology and Development Center during the 12 month period starting March 1, 1994. Progress is reported in both ideal and resistive MHD modeling of TFTR plasmas. The development of codes to calculate the significant effects of highly anisotropic pressure distributions is discussed along with results from this model

  14. Chemistry of gaseous lower-valent actinide halides. Technical progress report

    Hildenbrand, D.L.

    1984-01-01

    Objective is to provide thermochemical data for key actinide halide and oxyhalide systems. Progress is reported on bond dissociation energies of gaseous ThCl 4 , ThCl 3 , ThCl 2 , and ThCl; bond dissociation energies of ruthenium fluorides; and mass spectroscopy of UF 6

  15. Savannah River Ecology Laboratory annual technical progress report of ecological research, period ending July 31, 1993

    Vaitkus, M.R.; Wein, G.R. [eds.; Johnson, G.

    1993-11-01

    This progress report gives an overview of research programs at the Savannah River Site. Topics include; environmental operations support, wood stork foraging and breeding, defense waste processing, environmental stresses, alterations in the environment due to pollutants, wetland ecology, biodiversity, pond drawdown studies, and environmental toxicology.

  16. High beta and second stability region transport and stability analysis. Technical progress report

    Hughes, M.H.; Phillips, M.W.

    1994-09-01

    This report summarizes MHD equilibrium and stability studies carried out at Grumman's Corporate Research Center during the 6 month period starting March 1, 1994. Progress is reported in both ideal and resistive MHD modeling of TFTR plasmas. The development of codes to calculate the significant effects of highly anisotropic pressure distributions is discussed along with initial results from this model

  17. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 1. Technical Report # 0919

    Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grade 1. These measures, available as part of easyCBM [TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from schools…

  18. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Kindergarten. Technical Report # 0921

    Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in kindergarten. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2008 and administered to approximately 2800 students from…

  19. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 3. Technical Report # 09-02

    Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  20. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 5. Technical Report # 09-01

    Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  1. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 2. Technical Report # 0920

    Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  2. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 7. Technical Report 0908

    Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  3. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 4. Technical Report # 09-03

    Alonzo, Julie; Lai, Cheng Fei; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  4. The Development of K-8 Progress Monitoring Measures in Mathematics for Use with the 2% and General Education Populations: Grade 8. Technical Report # 09-04

    Lai, Cheng Fei; Alonzo, Julie; Tindal, Gerald

    2009-01-01

    In this technical report, we describe the development and piloting of a series of mathematics progress monitoring measures intended for use with students in grades kindergarten through eighth grade. These measures, available as part of easyCBM[TM], an online progress monitoring assessment system, were developed in 2007 and 2008 and administered to…

  5. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2012

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium...... and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities on fusion materials research (Tungsten and ODSFS). Other activities are system analysis...

  6. Association Euratom - DTU, Technical University of Denmark, Department of Physics - Annual Progress Report 2013

    The programme of the Research Unit of the Fusion Association Euratom – DTU, Technical University of Denmark covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium...... and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities on fusion materials research (Tungsten and ODSFS). Other activities are system analysis...

  7. [Review of draft Crystalline Repository Project reports]: Technical progress report, CY 1985-1986

    1986-01-01

    During the period (CY 1985-86) of this report, the Wisconsin Radioactive Waste Review Board provided technical services under the contract with DOE. These included Participation in the development of variables and screening techniques that would be used in identifying those rock bodies in the Area Recommendation Report (ARR); reviewing and commenting on the report and developing a procedure in which local residents could have input into the process; sought resumption of negotiations with DOE on a full Consultation and Cooperation (CandC) agreement; and Participating in workshops and provided comments on two major DOE transportation documents, ''Transportation Business Plan: Strategy Options Document,'' and ''Transportation Institutional Plan.''

  8. New imaging systems in nuclear medicine. Technical progress report, July 1, 1975--March 15, 1976

    Brownell, G.L.

    1976-01-01

    This progress report covers four areas: development of positron instrumentation, development of NUMEDICS computer system and software, application of cyclotron-produced isotopes ( 11 C, 68 Ga, 13 N, 15 O, and 82 Rb), and application of the NUMEDICS computer system in nuclear medicine. The development of transverse section positron imaging has had a significant impact and a positron camera was designed specifically for transverse section imaging of heart and lungs. The computer net (NUMEDICS II) is progressing rapidly in design and software development. Clinical studies have demonstrated the feasibility of measuring cerebral blood flow using a variety of positron emitting radiopharmaceuticals and oxygen utilization using 15 O 2 . Rubidium-82 also appears to be a promising agent for measurement of cerebral blood flow

  9. Nuclear structure theory. Technical progress report, September 1, 1982-August 31, 1984

    French, J.B.; Koltun, D.S.

    1984-01-01

    Research progress is reported. Spectral Averaging studies are outlined including the theory of level densities for interacting nucleons, the properties of single-particle nuclear excitations, spectral distributions for fixed symmetries, and applications to the secular behavior of fluctuation measures in complex nuclei. Collective States research is described, in particular the boson-fermion symmetries which are related to the U(5) limit of the interacting boson model. Nuclear Reaction studies are described including the statistical theory of pion absorption, direct reactions at intermediate energies, and the properties of the off-shell πN t-matrix. Progress is reported on the quark theory of nuclear matter and the construction of models for a Fermi fluid which, near the nuclear ground state, is a fluid of nucleons composed of quarks, and, at high densities or temperatures, is a quark fluid. Applications of formal scattering theory to the study of phase-conjugate optics are discussed. Publications are listed

  10. AFR spent fuel storage program. Technical progress report, January 1981-March 1981

    1981-01-01

    Work on this project is focused on developing design and licensing information for the model facility. Deliverables were submitted to DOE for facility modification, security design, and licensing documentation. Work is essentially complete on the high-density rack design with deliverable planned for April 30, 1981. A continuing program for completion of design and licensing information development was initiated by AGNS in February 1981. Progress to date is satisfactory

  11. U.C. Davis high energy particle physics research: Technical progress report -- 1990

    NONE

    1990-12-31

    Summaries of progress made for this period is given for each of the following areas: (1) Task A--Experiment, H1 detector at DESY; (2) Task C--Experiment, AMY detector at KEK; (3) Task D--Experiment, fixed target detectors at Fermilab; (4) Task F--Experiment, PEP detector at SLAC and pixel detector; (5) Task B--Theory, particle physics; and (6) Task E--Theory, particle physics.

  12. Nuclear structure theory. Annual technical progress report, October 1, 1979-August 31, 1980

    French, J.B.; Koltun, D.S.

    1980-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: statistical spectroscopy (including random matrix methods, with applications to fluctuations in spectra and in strength distributions, and to problems of ergodicity; group symmetries in spectral-distribution theory; electromagnetic and β transitions); meson scattering and absorption by nuclei (including general scattering theory with absorption, multiple scattering theory and its reactive content, statistical theory of absorption); and meson currents in electromagnetic transitions

  13. Nuclear methods in chemical kinetics. Technical progress report, April 1, 1978--March 31, 1979

    1979-01-01

    Significant progress was achieved in the following products: (1) gas phase thermal F-to-HF reactions; (II) gas phase thermal 18 F olefinic addition reactions; (III) steady state hot atom kinetic theory; (IV) moderator effects on nuclear recoil 18 F substitution reactions; and (V) new experimental methodology. New work has been initiated upon the development of a realisitic potential form of kinetic collision theory

  14. High energy particle physics at Purdue. Annual technical progress report, March 1982-March 1983

    Gaidos, J.A.; Koltick, D.S.; Loeffler, F.J.

    1983-01-01

    Progress is reported in these areas: a study of electron-positron annihilation using the High Resolution Spectrometer at SLAC; proton decay; extensive muon showers; gamma ray astronomy; the DUMAND project; theoretical work on fundamental problems in electromagnetic, weak, strong, and gravitational interactions; chi production by hadrons; p-nucleus interactions; development of the Collider Detector at Fermilab; and study of the observed hadrons as the relativistic bound states of baryons and antibaryons

  15. Deep vadose zone remediation: technical and policy challenges, opportunities, and progress in achieving cleanup endpoints

    Wellman, D.M.; Freshley, M.D.; Truex, M.J.; Lee, M.H.

    2013-01-01

    Current requirements for site remediation and closure are standards-based and are often overly conservative, costly, and in some cases, technically impractical. Use of risk-informed alternate endpoints provides a means to achieve remediation goals that are permitted by regulations and are protective of human health and the environment. Alternate endpoints enable the establishment of a path for cleanup that may include intermediate remedial milestones and transition points and/or regulatory alternatives to standards-based remediation. A framework is presented that is centered around developing and refining conceptual models in conjunction with assessing risks and potential endpoints as part of a system-based assessment that integrates site data with scientific understanding of processes that control the distribution and transport of contaminants in the subsurface and pathways to receptors. This system-based assessment and subsequent implementation of the remediation strategy with appropriate monitoring are targeted at providing a holistic approach to addressing risks to human health and the environment. This holistic approach also enables effective predictive analysis of contaminant behavior to provide defensible criteria and data for making long-term decisions. Developing and implementing an alternate endpoint-based approach for remediation and waste site closure presents a number of challenges and opportunities. Categories of these challenges include scientific and technical, regulatory, institutional, and budget and resource allocation issues. Opportunities exist for developing and implementing systems-based approaches with respect to supportive characterization, monitoring, predictive modeling, and remediation approaches. (authors)

  16. Deep vadose zone remediation: technical and policy challenges, opportunities, and progress in achieving cleanup endpoints

    Wellman, D.M.; Freshley, M.D.; Truex, M.J.; Lee, M.H. [Pacific Northwest National Laboratory, Richland, Washington (United States)

    2013-07-01

    Current requirements for site remediation and closure are standards-based and are often overly conservative, costly, and in some cases, technically impractical. Use of risk-informed alternate endpoints provides a means to achieve remediation goals that are permitted by regulations and are protective of human health and the environment. Alternate endpoints enable the establishment of a path for cleanup that may include intermediate remedial milestones and transition points and/or regulatory alternatives to standards-based remediation. A framework is presented that is centered around developing and refining conceptual models in conjunction with assessing risks and potential endpoints as part of a system-based assessment that integrates site data with scientific understanding of processes that control the distribution and transport of contaminants in the subsurface and pathways to receptors. This system-based assessment and subsequent implementation of the remediation strategy with appropriate monitoring are targeted at providing a holistic approach to addressing risks to human health and the environment. This holistic approach also enables effective predictive analysis of contaminant behavior to provide defensible criteria and data for making long-term decisions. Developing and implementing an alternate endpoint-based approach for remediation and waste site closure presents a number of challenges and opportunities. Categories of these challenges include scientific and technical, regulatory, institutional, and budget and resource allocation issues. Opportunities exist for developing and implementing systems-based approaches with respect to supportive characterization, monitoring, predictive modeling, and remediation approaches. (authors)

  17. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2011-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

  18. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

    2010-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

  19. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2009

    Korsholm, S B; Michelsen, P K; Rasmussen, J J; Westergaard, C M [eds.

    2010-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009. (Author)

  20. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M. (eds.)

    2009-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

  1. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2008

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

    2009-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. New activities in technology related to development of high temperature superconductors have been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008. (Author)

  2. Progress report [of] Technical Physics and Prototype Engineering Division, April 1982 - March 1984

    Ramamurthi, S.S.; Chaudhry, Ramesh

    1985-01-01

    The work done by the Technical Physics and Prototype Engineering Division of the Bhabha Atomic Research Centre (BARC) at Bombay during the period from April 1982 to March 1984 is described in the form of summaries. The main thrust of the work of the Division is towards designing, developing, fabricating and if needed, producing on a large scale various instruments, equipment and components required for the programmes of the BARC and the Department of Atomic Energy. The summaries describing the work are grouped under the headings:(1) vacuum, (2) surface analysis, (3) mass spectrometry, (4) electronics, (5) cryogenics, (6) crystals and detectors, (7) glass technology and devices, and (8) optoelectronics. A list of publications of the staff-members of the Division during the report period is given. (M.G.B.)

  3. Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

    Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J.

    2008-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

  4. Association Euratom - Risoe National Laboratory, Technical Univ. of Denmark. Annual progress report 2007

    Michelsen, P.K.; Korsholm, S.B.; Rasmussen, J.J. (eds.)

    2008-04-15

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. The activities in technology on investigations of radiation damage of fusion reactor materials have been phased out during 2007. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2007. (Author)

  5. Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark. Annual progress report 2010

    Korsholm, S.B.; Michelsen, P.K.; Rasmussen, J.J.; Westergaard, C.M.

    2011-04-01

    The programme of the Research Unit of the Fusion Association Euratom - Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its interaction with the plasma equilibrium and particles. The effort includes both first principles based modelling, and experimental observations of turbulence and of fast ion dynamics by collective Thomson scattering. Within fusion technology there are activities related to development of high temperature superconductors. Other activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2010. (Author)

  6. Fusion programs in applied plasma physics. Technical progress report, July 11, 1992--May 31, 1993

    1993-07-01

    This report summarizes the progress made in theoretical and experimental research funded by US Department of Energy Grant No. DE-FG03-92ER54150, during the period July 11, 1992 through May 31, 1993. Four main tasks are reported: applied plasma physics theory, alpha particle diagnostic, edge and current density diagnostic, and plasma rotation drive. The report also discusses the research plans for the theory and experimental programs for the next grant year. Reports and publications supported by the grant during this period are listed in the final section.

  7. Decontamination Systems Information and Research Program. Quarterly technical progress report, July 1--September 30, 1993

    1993-10-01

    Progress reports are presented for the following projects: systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies--drain-enhanced soil flushing (DESF) for organic contaminants removal; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors--monolayer and multilayer self-assembled films for chemical sensors; Winfield Lock and Dam remediation; Winfield cleanup survey; assessment of technologies for hazardous waste site remediation--non-treatment technologies and pilot scale test facility implementation; assessment of environmental remediation storage technology; assessment of environmental remediation excavation technology; assessment of environmental remediation monitoring technology; and remediation of hazardous sites with steam reforming.

  8. Salt repository project: Technical progress report for the quarter 1 April--30 June 1987

    1987-01-01

    This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of Energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation

  9. Nuclear structure theory. Annual technical progress report, October 1, 1978-September 30, 1979

    French, J.B.; Koltun, D.S.

    1979-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: Statistical spectroscopy, including: Random matrix methods, with applications to fluctuations in spectra and in strength distributions, and to problems of ergodicity; Group symmetries in spectral-distribution theory; Electromagnetic and β transitions. Meson scattering and absorption by nuclei, including: general scattering theory with absorption, multiple scattering theory and its reactive content, statistical theory of absorption, theory of the absorption operator (πNN vertex), theory of πN scattering. A list of publications is included

  10. Combined macroscopic and microscopic approach to the fracture of metals. Technical progress report

    Asaro, R.J.; Gurland, J.; Needleman, A.; Rice, R.J.

    1979-06-01

    Progress is reported on microscopic fracture mechanisms, including studies of void and crack initiation in steels in the absence and presence of hydrogen, the effects of hydrogen on ductile fracture in medium and high carbon steels; elastic--plastic crack growth including the quasi-stable growth of cracks in ductile solids under increasing load and conditions of instability; and elevated temperature rupture including analysis of the stress field near a crack tip in an elastic-nonlinear viscous material under tensile load as well as the processes of diffusion, and cavitation of grain boundaries in plastically creeping materials

  11. Theoretical nuclear physics. Task B. Technical progress report, August 1, 1982-September 30, 1983

    1983-01-01

    Progress is reported on the following studies: (a) double delta interactions in pion double charge exchange; (b) isovector correlations in pion-nucleus scattering; (c) nuclear structure effects in pion single charge exchange; (d) a perspective on sequential transfer reactions; (e) inelastic and charge exchange scattering theory; (f) magnitude of the first order DWBA description of the two nuclear transfer reactions; (g) nonlocality effects on deuteron transfer reactions; (h) evaluation of external radial integrals in inelastic electron scattering; (i) experimental observables as a function of Dirac invariant amplitudes; (j) Dirac shell-model wavefunctions in inelastic electron scattering; and (k) impulse approximation Dirac theory of inelastic proton nucleus collective excitations. Publications are listed

  12. High energy particle physics at Purdue. Annual technical progress report, March 1983-March 1984

    Gaidos, J.A.; Koltick, D.S.; Loeffler, F.J.

    1984-01-01

    Progress is reported in these areas: a study of electron-positron annihilation using the High Resolution Spectrometer; experimental study of proton decay; gamma ray astrophysics; the DUMAND project; fundamental problems in the theory of gravitational, electromagnetic, weak, and strong interactions; chi production by hadrons; study of collective phenomena; search for the onset of collective phenonmena; work on the Collider Detector at Fermilab; search for a deconfined quark-gluon phase of strongly interacting matter at the FNAL proton-antiproton collider; and development of an electrodeless drift chamber

  13. Physics of correlated systems. Technical progress report, December 1996 - June 1999

    Greene, C.H.

    1999-01-01

    During the current funding period, which covers a period of approximately 2.5 years, the authors have tackled a number of challenging problems that involve nonperturbative particle-particle interactions in two qualitatively different areas: electron-electron interactions in photoionization and photodetachment, and atom-atom interactions in Bose-Einstein condensates. The following discusses the progress achieved in these different areas. The emphasis in this summary will concentrate on approximately the last year of research accomplishments, although the bibliography below includes all research publications that were supported during the time period of this grant

  14. Decontamination Systems Information and Research Program. Quarterly technical progress report, July 1--September 30, 1993

    1993-10-01

    Progress reports are presented for the following projects: systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies--drain-enhanced soil flushing (DESF) for organic contaminants removal; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors--monolayer and multilayer self-assembled films for chemical sensors; Winfield Lock and Dam remediation; Winfield cleanup survey; assessment of technologies for hazardous waste site remediation--non-treatment technologies and pilot scale test facility implementation; assessment of environmental remediation storage technology; assessment of environmental remediation excavation technology; assessment of environmental remediation monitoring technology; and remediation of hazardous sites with steam reforming

  15. Plasma physics research (Tokapole II). Technical progress report, October 1, 1981-December 31, 1983

    1983-01-01

    Progress during the 27-month period, October 1, 1981 to December 31, 1983 on Tokapole II research is described. Tokapole II is a 4-node poloidal divertor tokamak that can also be run as an octupole. Research during this period has concentrated on studies of discharges with safety factor q less than one and on the identification of the shear Alfven wave resonance. Other topics include measurements of the loop voltage reduction through ECRH startup, plasma gun refueling, fluctuations and transport, pumped limiter studies, plasma-wall interactions, diagnostic development, polarization of electron cyclotron emission, and poloidal ohmic heating

  16. Nuclear structure theory. Annual technical progress report, October 1, 1977--September 30, 1978

    French, J.B.; Koltun, D.S.

    1978-01-01

    Progress during the past year in the following areas of nuclear structure and reaction theory is summarized: statistical spectroscopy, including random matrix methods, with applications to fluctuations in spectra and in strength distributions, and to problems of erogodicity; group symmetries in spectral distribution theory; effective interactions; statistical reaction theory, applied to ''deep inelastic'' collisions of heavy ions, and to pion absorption by nuclei; meson scattering and absorption by nuclei, including general scattering theory with absorption, multiple scattering theory and its reactive content, models for absorption, theory of the absorption operator (πNN vertex), theory of πN scattering. A list of publications is included

  17. Salt Repository Project technical progress report for the quarter 1 January--31 March 1987

    1988-03-01

    This document reports the progress being made each quarter on the development of a geologic repository in salt for the permanent disposal of high-level nuclear waste. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Nuclear Waste Isolation, a prime contractor of the US Department of energy (DOE) Salt Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Nuclear Waste Isolation. 23 refs., 1 fig

  18. Nuclear structure theory. Annual technical progress report, September 1, 1980-August 31, 1981

    French, J.B.; Koltun, D.S.

    1981-01-01

    This report summarizes progress during the past year in the following areas of nuclear structure and reaction theory: (1) statistical spectroscopy, including: random matrix methods, with applications to fluctuations in spectra and in strength distributions; group symmetries in spectral-distribution theory; electromagnetic and β transitions, limits to time-reversal symmetry breaking in the nucleon-nucleon interaction; (2) meson scattering and absorption by nuclei, including: general scattering theory with absorption, multiple scattering theory and its reactive content, statistical theory of absorption; and (3) meson currents in electromagnetic transitions

  19. Thermionic cogeneration burner assessment study. Third quarterly technical progress report, April-June, 1983

    1983-01-01

    The specific tasks of this study are to mathematically model the thermionic cogeneration burner, experimentally confirm the projected energy flows in a thermal mock-up, make a cost estimate of the burner, including manufacturing, installation and maintenance, review industries in general and determine what groups of industries would be able to use the electrical power generated in the process, select one or more industries out of those for an in-depth study, including determination of the performance required for a thermionic cogeneration system to be competitive in that industry. Progress is reported. (WHK)

  20. Nuclear safety. Technical progress journal, January--March 1996: Volume 37, No. 1

    Muhlheim, M D [ed.

    1996-01-01

    Nuclear Safety is a journal that covers significant issues in the field of nuclear safety. Its primary scope is safety in the design, construction, operation, and decommissioning of nuclear power reactors worldwide and the research and analysis activities that promote this goal, but is also encompasses the safety aspects of the entire nuclear fuel cycle, including fuel fabrication, spent-fuel processing and handling, and nuclear waste disposal, the handling of fissionable materials and radioisotopes, and the environmental effects of all these activities. Individual articles are indexed separately for the data base.

  1. Nuclear Safety Technical Progress Journal, January--June 1995. Volume 36, No. 1

    Silver, E G [ed.

    1995-01-01

    This journal covers significant issues in the field of nuclear safety. Its primary scope is safety in the design, construction, operation, and decommissioning of nuclear power reactors worldwide and the research and analysis activities that promote this goal, but it also encompasses the safety aspects of the entire nuclear fuel cycle, including fuel fabrication, spent-fuel processing and handling, and nuclear waste disposal, the handling of fissionable materials and radioisotopes, and the environmental effects of all these activities. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  2. Superconducting fault current limiter. Fifth quarterly technical progress report, August 8, 1978-November 7, 1979

    1979-01-01

    Progress in the development of fault current limiters for superconducting power transmission systems is reported. The analysis and design of a magnetically switched resistive device and the experimental program were emphasized and reported. A transient heat transfer model was developed which indicates the parameters which are important in determining the thermal heating and recovery of the superconduting film. Designs for the switching coil and the S/C element were also carried out and are reported. A four-pole magnetic coil is recommended; this generates a magnetic field which is nearly perpendicular to spiral or helical S/C film geometrics. A spirally-designed, 3000 ohm limiter is shown to be able to fit within a .5 to 1m inner radius, .05 to .03 m wide, 1.3 to 3.9 m long annualr region. The experimental program has included work on materials development and on prepartion of the switching and thermal recovery experimental facility. The material development program has uncovered several serious short-comings of NbN as the S/C film material. Macroscopic holes and surface debris, and microscopic imperfections reduce the critical current density below the expected value and, in addition, cause nonuniform switching. Reasons for these effects are postulated, and a continuing, vigorous materials program is suggested in hopes of alleviating these problems. Virtually all of the experimental equipment had been installed, and so the magnetic switching and thermal recovery experiments can begin and progress during the next quarter. (LCL)

  3. An accelerator neutron source for BNCT. Technical progress report, 1 June 1993--31 May 1994

    Blue, T.E.; Vafai, K.

    1994-02-01

    This is the progress report for the project entitled, ''An Accelerator Neutron Source for BNCT.'' The progress report is for the period from July 1, 1993 to date. The overall objective of our research project is to develop an Accelerator Epithermal Neutron Irradiation Facility (AENIF) for Boron Neutron Capture Therapy (BNCT). The AENIF consists of a 2.5 MeV high current proton accelerator, a lithium target to produce source neutrons, and a moderator/reflector assembly to obtain from the energetic source neutrons an epithermal neutron field suitable for BNCT treatments. Our project goals are to develop the non-accelerator components of the AENIF, and to specifically include in our development: (1) design, numerical simulation, and experimental verification of a target assembly which is capable of removing 75 kW of beam power; (2) re-optimization of the moderator assembly design based on in-phantom dose assessments using neutron spectra calculated in phantom and an energy-dependent neutron Relative Biological Effectiveness (RBE); (3) construction of a prototype moderator assembly and confirmation of its design by measurements; (4) design of the shielding of the accelerator and treatment rooms for an AENIF; and (5) design of a high energy beam transport system which is compatible with the shielding design and the thermal-hydraulic design

  4. Technical progress report, Contracts DE-AC02-81ER40014, 40015 and 40016

    1981-01-01

    This Progress Report summarizes work carried out at the Nuclear Physics Laboratory of the University of Colorado from November 1, 1980 through July 31, 1981, under contracts between the University of Colorado and the United States Department of Energy. The shorter report period of nine months is due to a change to an earlier submission date this year for our proposal for support to begin February 1, 1982. Cyclotron operation, research, and development have been supported under contract DE-AC02-81ER40014. The AVF cyclotron has continued to provide reliable and versatile beams of protons, deuterons, 3 He and 4 He. A wide variety of research results in direct reactions, nuclear structure, and compound reaction mechanisms can be noted in this Progress Report, correlated in many cases to current problems in intermediate energy physics. Theoretical work on nuclear reactions, carried out under contract DE-AC02-81ER40015, has been well matched to our experimental programs in low and intermediate energy physics. One important result has been the recasting of the DWBA in an eikonal expansion suited to high energy reactions. Our efforts in intermediate energy physics, under contract DE-AC02-81ER40016, have emphasized pion scattering studies at LAMPF and TRIUMF and proton induced charge exchange reactions at IUCF. Data for an important test of hadronic charge symmetry have been completed at two energies, using elastic pion-deuteron scattering

  5. The role of technical progress in the process of recalculating oil reserves; Le role du progres technique dans le processus de renouvellement des reserves petrolieres

    Boulard, J.N. [Total/Fina/Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

    1999-08-01

    Contrary to the concept of resources (which is essentially a geological one), the notion of reserves designates the quantities that are technically and economically recoverable. Beyond the production-related effect, the reserves therefore evolve over time in accordance with numerous technical and economic parameters. Among these parameters, it can be seen that technical progress plays a considerable role throughout the process of converting resources into reserves, including progress in the identification, accessibility and processing of the resources, and improvements in economic viability. After having tackled the problem of measuring the 'technical progress effects' and citing examples, we demonstrate that the evolution in oil reserves is subject to three types of impact. These are a quantitative impact by significantly improving the recovery rates or making it possible to identify hitherto undetectable oil fields, a qualitative impact by widening the resource base thanks to the adoption of new categories of oil (in particular the so-called 'unconventional' oils) and by carrying out the gradual substitution between these resources of differing qualities. There is also a dynamic impact, through the acceleration of resource availability. Through these three approaches, technical progress makes makes it possible to ensure continuity in oil supply and contributes significantly to the recalculation of reserves. It therefore acts as a compensating factor, counterbalancing the progressive depletion of resources. (author)

  6. GT-MHR COMMERCIALZATION STUDY. TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD JUNE 1 THROUGH JUNE 30, 2003

    SHENOY, A.S.

    2003-01-01

    A271 GT-MHR COMMERCIALZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD JUNE 1 THROUGH JUNE 30, 2003. Petten was provided with irradiation dimensional change data for both fuel compacts and H-451 graphite for design of the graphite sleeves that hold the fuel compacts to be irradiated in HFR-EU2. The Fuel Sample Product Specification for the Fuel Performance Irradiation Test Capsule MHR-2 was completed and approved. A Work Breakdown Structure was prepared for the development and qualification of advanced coated-particle fuels capable of meeting anticipated fuel performance requirements and work was initiated on preparation of schedules and a cost estimates for the test matrices

  7. GT-MHR COMMERCIALIZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD AUGUST 1 THROUGH AUGUST 31, 2003

    Shenoy, A.S.

    2003-01-01

    OAK A271 GT-MHR COMERCIALiZATION STUDY TECHNICAL PROGRESS AND COST MANAGEMENT REPORT FOR THE PERIOD AUGUST 1 THROUGH AUGUST 31, 2003. In the process of fabricating the MHR-1 irradiation test capsule, Petten has advised that three thermocouples (out of 24) and the Self Powered Neutron detector were damaged during high temperature brazing with the upper capsule lid. Procurement of new TCs and SPN is in process but there will be a delay in the irradiation test of about nine weeks. Startup of the irradiation is now projected to be July or August 2004. In preparation for performing the nuclear design analysis activities required by the advanced fuel studies task, a complete 3-D nuclear design analysis is first being performed of the GT-MHR reference design. This will serve as the baseline for studies of the advanced fuel nuclear design performance

  8. Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

    Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

    1979-07-01

    Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis

  9. Repository Technology Program: Technical progress report for the period May 29, 1986--June 30, 1987

    1988-10-01

    This document reports the progress made in the 13-month period from May 29, 1986--June 30, 1987, on the development of a second geologic repository in rocks other than those being considered for a first repository. Subsequent periods will be covered in reports to be issued on a semiannual basis. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Waste Technology Development (OWTD), a prime contractor of the US. Department of Energy (DOE) Repository Technology Program (RTP) Office in the Repository Technology and Transportation Division (RTTD) of the Office of Geologic Repositories (OGR). The studies include work by other DOE prime contractors and by contractors to the OWTD. 50 refs

  10. Waste Isolation Safety Assessment Program. Technical progress report for FY-1978

    Brandstetter, A.; Harwell, M.A.; Howes, B.W.; Benson, G.L.; Bradley, D.J.; Raymond, J.R.; Serne, R.J.; Schilling, A.H.

    1979-07-01

    Associated with commercial nuclear power production in the United States is the generation of potentially hazardous radioactive wastes. The Department of Energy (DOE) is seeking to develop nuclear waste isolation systems in geologic formations that will preclude contact with the biosphere of waste radionuclides in concentrations which are sufficient to cause deleterious impact on humans or their environments. Comprehensive analyses of specific isolation systems are needed to assess the expectations of meeting that objective. The Waste Isolation Safety Assessment Program (WISAP) has been established at the Pacific Northwest Laboratory (operated by Battelle Memorial Institute) for developing the capability of making those analyses. Progress on the following tasks is reported: release scenario analysis, waste form release rate analysis, release consequence analysis, sorption-desorption analysis, and societal acceptance analysis. (DC)

  11. Texas Experimental Tokamak: A plasma research facility. Technical progress report, November 1, 1993--October 31, 1994

    Wootton, A.J.

    1994-07-01

    The purpose is to operate and maintain TEXT Upgrade as a complete facility for applied tokamak physics in order to elucidate the mechanisms of working gas, impurity, and thermal transport in tokamaks and in particular to understand the role of turbulence. So that they can continue to study the physics that is most relevant to the fusion program, TEXT completed a significant device upgrade this year. The new capabilities of the device and new and innovative diagnostics were exploited in all main program areas including: (1) configuration studies; (2) electron cyclotron heating physics; (3) improved confinement modes; (4) edge physics/impurity studies; (5) central turbulence and transport; and (6) transient transport. Details of the progress in each of the research areas are described.

  12. Texas Experimental Tokamak: A plasma research facility. Technical progress report, November 1, 1993--October 31, 1994

    Wootton, A.J.

    1994-07-01

    The purpose is to operate and maintain TEXT Upgrade as a complete facility for applied tokamak physics in order to elucidate the mechanisms of working gas, impurity, and thermal transport in tokamaks and in particular to understand the role of turbulence. So that they can continue to study the physics that is most relevant to the fusion program, TEXT completed a significant device upgrade this year. The new capabilities of the device and new and innovative diagnostics were exploited in all main program areas including: (1) configuration studies; (2) electron cyclotron heating physics; (3) improved confinement modes; (4) edge physics/impurity studies; (5) central turbulence and transport; and (6) transient transport. Details of the progress in each of the research areas are described

  13. New imaging systems in nuclear medicine. Technical progress report, October 1, 1976--May 31, 1977

    Brownell, G.L.

    1977-01-01

    Work carried out on the development of instrumentation and techniques for positron scintigraphy is discussed. Progress in positron imaging instrumentation and applications is detailed. The assembly and initial evaluation of the new multicrystal positron camera, PC-II, has been completed. Images have been obtained in both two and three-dimensions which demonstrate the basic physical properties of the instrument. Successful measurements using transverse section imaging have been carried out on animals and human volunteers. Physiological investigation using PC-II is proceeding. A flexible and accurate computer program has been developed for transverse section reconstruction of data acquired by PC-II. This program makes it possible to reconstruct both the activity distribution and the distribution of absorption. The program has been developed in such a way that it can handle variations in the data collection procedure. Clinical studies using PC-I and PC-II are being carried on in areas of heart, lung and brain

  14. [Geothermal system temperature-depth database and model for data analysis]. 5. quarterly technical progress report

    Blackwell, D.D.

    1998-04-25

    During this first quarter of the second year of the contract activity has involved several different tasks. The author has continued to work on three tasks most intensively during this quarter: the task of implementing the data base for geothermal system temperature-depth, the maintenance of the WWW site with the heat flow and gradient data base, and finally the development of a modeling capability for analysis of the geothermal system exploration data. The author has completed the task of developing a data base template for geothermal system temperature-depth data that can be used in conjunction with the regional data base that he had already developed and is now implementing it. Progress is described.

  15. Radioecology of natural systems in Colorado. Thirteenth technical progress report, May 1, 1974--April 30, 1975

    Whicker, F.W.

    1975-01-01

    Progress is reported on studies on the behavior of fallout radionuclides ( 137 Cs and 90 Sr) in selected organisms and natural ecosystems in Colorado. Components of alpine tundra, montane forests, shortgrass plains, and freshwater lakes and streams are currently under investigation. A study on the effect of gut passage on the mean diameter of monodisperse PuO 2 microspheres was initiated. Studies on plutonium in the terrestrial environs of Rocky Flats were initiated in the summer of 1972. Soil movement measurements were conducted to bear on the question of plutonium stability in contaminated areas. The relative importance of root uptake versus aerial deposition was evaluated in the field utilizing a sod block transplant procedure. The study on radiation effects on shortgrass plains vegetation was continued with emphasis on long-term changes in community structure under chronic irradiation stress and recovery patterns. (U.S.)

  16. Research in elementary particle physics. Technical progress report, June 1, 1985-May 31, 1986

    Kirsch, L.E.; Schnitzer, H.J.; Bensinger, J.R.; Abbott, L.F.; Blocker, C.A.

    1986-01-01

    Progress is reported in both experimental and theoretical elementary particle research. Experimental activities include: construction of the Forward Electromagnetic Shower Counters for the Collider Detector at Fermilab (CDF); a test run in the CDF, involving observation of a small number of proton-antiproton collisions; design of a self-contained single wire proportional chamber with pressure and temperature sensing for monitoring the gain of gases used by various components of the CDF; data acquisition, and calibration. Also included are a search for a dibaryon of strangeness=-1; hyperon weak radiative decay. Theoretical research is reported in the areas of quantum field theory, string theory, elementary particle phenomenology, cosmology, field theory in curved spacetimes, and cosmology. 34 refs

  17. Nuclear structure theory. Annual technical progress report, 1 July 1974--30 June 1975

    French, J.B.; Koltun, D.S.

    1975-01-01

    Progress during the past year is summarized for the following areas of nuclear structure and reaction theory: Meson interactions with nucleons and nuclei, including inelastic scattering of pions, three-body theories of scattering and absorption of pions by deuterons, and π-p bremsstrahlung. Theory of the effective interaction, including behavior of the expansion in orders of the reaction matrix. Statistical spectroscopy including fluctuations in energy levels and excitation strengths, and sum rules and strength distributions for various excitation processes, including single-nucleon transfer, β decay and multipole giant resonances. Studies of the inverse scattering problem. Studies of nuclear symmetries, of nuclear clustering, and of general nuclear structure by α-transfer reactions, and of nuclear shapes by (d, 3 He) reactions. (U.S.)

  18. Scientific and technical progress in high-energy astrophysics at INPE

    Bui-Van, N.A.; Jayanthi, U.B.; Jardim, J.O.D.; Braga, J.; Santo, C.M.E.

    1984-01-01

    The recent advances in high-energy Astrophysics pertains to the study of compact objects in galactic nuclei, binary systems and pulsars. These aspects are best understood by the study of the emissions in X- and gamma rays of these objects through the temporal variation in flux and spectrum. The Southern Hemisphere offers some of the unique objects for investigations such as galactic center, the Vela pulsar etc. For high temporal and spectra resolution studies two telescopes 'GeLi' and 'Pulsar' were designed and constructed. To support these scientific activities, a program in balloon launching and data acquisition facilities has been developed since 1971. The 'Balloon Launching Center' of INPE has capacity to launch balloons of -850,000 m 3 with payloads weighting about 1,000 Kg. Taking advantage of these facilities, project 'Bantar', with the goal to measure the atmospheric gamma-ray radiation in the Antartic Region, is under progress. (Author) [pt

  19. Crystalline Repository Project: Technical progress report for the period October 1, 1982--May 28, 1986

    1988-11-01

    This document reports the progress made on the development of a second geologic repository in crystalline rocks during the duration of the Crystalline Repository Project from its inception in October 1982 to its termination in May 1986. The reporting elements are arranged by the work breakdown structure so that related studies are presented together. The studies are reported by the Office of Waste Technology Development (OWTD), successor to the Office of Crystalline Repository Development. OWTD is a prime contractor of the US Department of Energy (DOE) Repository Technology Program Office, itself the successor to the Crystalline Repository Project Office. The studies include work by other DOE prime contractors and by contractors to the Office of Crystalline Repository Development. 151 refs

  20. Savannah River Ecology Laboratory. Annual technical progress report of ecological research

    Smith, M.H.

    1996-01-01

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA). The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts basic and applied ecological research, as well as education and outreach programs, under a contract with the U.S. Department of Energy (DOE) at the Savannah River Site (SRS) near Aiken, South Carolina. Significant accomplishments were made during the past year in the areas of research, education and service. The Laboratory's research mission was fulfilled with the publication of two books and 143 journal articles and book chapters by faculty, technical and students, and visiting scientists. An additional three books and about 80 journal articles currently are in press. Faculty, technician and students presented 193 lectures, scientific presentations, and posters to colleges and universities, including minority institutions. Dr. J Vaun McArthur organized and conducted the Third Annual SREL Symposium on the Environment: New Concepts in Strewn Ecology: An Integrative Approach. Dr. Michael Newman conducted a 5-day course titled Quantitative Methods in Ecotoxicology, and Dr. Brian Teppen of The Advanced Analytical Center for Environmental Sciences (AACES) taught a 3-day short course titled Introduction to Molecular Modeling of Environmental Systems. Dr. I. Lehr Brisbin co-hosted a meeting of the Crocodile Special Interest Group. Dr. Rebecca Sharitz attended four symposia in Japan during May and June 1996 and conducted meetings of the Executive Committee and Board of the International Association for Ecology (ENTECOL)

  1. Gas-Cooled Thermal Reactor Program. Semiannual technical progress report, October 1, 1982-March 3, 1983

    1983-06-01

    This report provides descriptions and results of the technical effort during the first half of FY 83 on the Gas-Cooled Thermal Reactor Program. The work on Integration and Management (WBS 01) includes the preparation of the Advanced Systems Concept Evaluation Plan and the Advanced Systems Technology Development Plan in addition to the program management activities. The Market Definition (WBS 03) efforts considered the application of the Modular Reactor System with reforming (MRS-R) to the production of methanol and ammonia and the refining of petroleum. Within the Plant Technology (WBS 13) task there were activities to develop anlytical methods for investigation of Coolant Transport Behavior and to define methods and criteria for High Temperature Structural Engineering design. In addition to the work on the advanced HTGR for process heat users, new activities were initiated in support of the HTGR-SC/C Lead plant Protect (WBS 30 and 31). The Plant Simulation task (WBS 31) was initiated to develop a computer code for simulation of plant operation and for plant transient systems analysis. The efforts on the advanced HTGR systems was performed under the Modular Systems task (WBS 41) to study the potential for multiple small reactors to provide lower costs, improved safety, and higher availability than the large monolithic core reactors

  2. Savannah River Ecology Laboratory. Annual technical progress report of ecological research

    Smith, M.H.

    1996-07-31

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA). The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts basic and applied ecological research, as well as education and outreach programs, under a contract with the U.S. Department of Energy (DOE) at the Savannah River Site (SRS) near Aiken, South Carolina. Significant accomplishments were made during the past year in the areas of research, education and service. The Laboratory`s research mission was fulfilled with the publication of two books and 143 journal articles and book chapters by faculty, technical and students, and visiting scientists. An additional three books and about 80 journal articles currently are in press. Faculty, technician and students presented 193 lectures, scientific presentations, and posters to colleges and universities, including minority institutions. Dr. J Vaun McArthur organized and conducted the Third Annual SREL Symposium on the Environment: New Concepts in Strewn Ecology: An Integrative Approach. Dr. Michael Newman conducted a 5-day course titled Quantitative Methods in Ecotoxicology, and Dr. Brian Teppen of The Advanced Analytical Center for Environmental Sciences (AACES) taught a 3-day short course titled Introduction to Molecular Modeling of Environmental Systems. Dr. I. Lehr Brisbin co-hosted a meeting of the Crocodile Special Interest Group. Dr. Rebecca Sharitz attended four symposia in Japan during May and June 1996 and conducted meetings of the Executive Committee and Board of the International Association for Ecology (ENTECOL).

  3. Dual curvature acoustically damped concentrating collector. Semiannual technical progress report, June 1-December 1, 1978

    None

    1978-12-01

    The project's first objective is to establish, analytically, the cost and performance of design choices within the boundaries of the basic proposed concept. With these cost and performance measures as a guide, the second project objective is to design a cost-effective Dual Curvature collector module and collector field array. The third objective is to establish technical and economic concept feasibility through prototype fabrication and test. The final objective is to define the Dual Curvature collector commercialization requirements. The Dual Curvature collector uses a unique reflector module consisting of a reflective film that is tensioned on a reflector support frame. The tensioned membrane (film) surface approximates a hyperbolic paraboloid that is capable of linear focusing when the surface tracks the sun's apparent motion in one axis. The reflective film can be backed by polystyrene foam with an air space between the film and the foam surfaces. This provides damping of the reflector surface to minimize the effect of wind gusts and physical impacts. The baseline collector is intended to operate at a concentration of ten (10) or greater with a nominal absorber temperature of 150/sup 0/C (300/sup 0/F). The Component Research and Analysis tasks which lead to the selection of a baseline collector configuration are discussed. Also, some preliminary results of the Collector Module Design task are presented.

  4. Pulverized coal firing of aluminum melting furnaces. First annual technical progress report, May 1978-June 1979

    West, C.E.; Hines, J.E.; Stewart, D.L. Jr.; Yu, H.

    1979-10-01

    The ultimate objective of this program is the commercial demonstration of an efficient, environmentally acceptable coal firing process suitable for implementation on melting furnaces throughout the aluminum industry. To achieve this goal, the program has been divided into two phases. Phase I has begun with the design and construction of a 350 lb/h (coal) staged slagging cyclone combustor (SSCC) attached to a 7-ft dia aluminum melting ladle furnace. Process development will culminate with a 1000 pph prototype SSCC firing a 40,000 lb capacity open hearth melting furnace at the Alcoa Laboratories. Phase II implementation is currently planned for Alcoa's Lafayette, IN, Works, where two of the ingot plant's five open hearth melting furnaces will be converted to utilize coal. In addition to confirmation of data gathered in Phase I, the effect of extended production schedule operation on equipment and efficiencies will be determined. This work would begin in 1982 pursuant to technical and economic evaluation of the process development at that time. A major design subcontract for assistance in the design of the SSCC is 80% completed.

  5. Technical support for open-cycle MHD program. Progress report, July--December 1978

    Doss, E D [ed.

    1979-06-01

    The support program for open-cycle MHD at Argonne National Laboratory is developing the analytical tools needed to investigate the performance of the major components in the combined cycle MHD/steam power system. The analytical effort is centered on the primary components of the system that are unique to MHD and also on the integration of these analytical representations into a model of the entire power producing system. The present project activities include modeling of the combustor, MHD channel, slag separator, and high-temperature air heater. In addition, these models are combined into a complete system model, which is at present capable of carrying out optimizations of the entire system relative to either thermodynamic efficiency or cost of electrical power. Also, in support of other aspects of the open-cycle program, test plans are developed and facility and program reviews are provided upon request in support of the needs and requirements of the DOE/MHD Division.

  6. Advanced direct liquefaction concepts for PETC generic units. Quarterly technical progress report, April 1992--June 1992

    1992-08-01

    CAER/UK: Detail coal and starting solvents from Wilsonville were analyzed to develop the data necessary to conduct process studies in the CO Pretreatment and Catalyst Evaluation segment of this program. A comparison of the solvent separation analysis with the distillation/separation used at Wilsonville showed that the residual solvent components contained a large amount of residual pentane soluble products. The ashy resid contained 3% iron and 400 ppM molybdenum. Although the iron content in the distillate and deashed resid was much less, namely about 200 ppM., the molybdenum concentrations in these fractions were not significantly reduced over the concentration in the ashy resid, i.e., 200 ppM in each. The pretreatment of coal with CO/H{sub 2}O in the presence of NaOH and Na{sub 2}CO{sub 3} has been shown to give a product which is lower in oxygen content and higher in hydrogen content compared to the raw coal. The atomic H/C ratios of the H{sub 2}O-insolubles, THF insolubles and the PA+A fractions of the products-together with the hydrogen consumption data suggested that the raw coal has been substantially depolymerized and hydrogenated via the WGS reaction during the pretreatment process. The extensive amount of molecular reconstruction that has occurred in the solid product was evident from the ease of solubilization of the product into pyridine. The result of the pretreatment process is a product which is highly reactive under hydroliquefaction conditions at 400{degrees}C. Reaction rates seem to be much faster than the raw coal, especially at shorter reaction times, providing the opportunity for major reductions in plant vessel sizes, and preliminary data has led us to believe that better efficiency in hydrogen utilization is achieved.

  7. Technical Progress Report on Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

    Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Ben Poulter; Sarah Woodhouse Murdock; Neil Sampson; Tim Pearson; Sarah Walker; Zoe Kant; Miguel Calmon; Gilberto Tiepolo

    2006-06-30

    The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st and July 30th 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool. Work is being carried out in Brazil, Belize, Chile, Peru and the USA.

  8. Optimal design and routing of power lines; ecological, technical and economic perspectives (OPTIPOL). Progress report 2009

    Bevanger, K.; Bartzke, G.; Broeseth, H.; Gjershaug, J.O.; Hanssen, F.; Jacobsen, K.-O.; Kvaloey, P.; May, R.; Nygaard, T.; Pedersen, H.C.; Reitan, O.; Refsnaes, S.; Stokke, S.; Vang, R.

    2009-12-15

    From 2009 inclusive, NINA has received economic support for research on power lines and wildlife from the Norwegian Research Council (NFR) through the RENERGI Programme. The project is named 'Optimal design and routing of power lines; ecological, technical and economic perspectives' (OPTIPOL). It is scheduled for 5 years (2009-1013) and is part of the activities within CEDREN, i.e. the Centre for environmental design of renewable energy (cf. http://www.cedren.no). With a grid close to 200 000 km overhead power-lines, the associated rights-of-way (ROW) affect huge land areas in Norway. The overall goal is to develop predict-ing tools for optimal routing of power lines from an environmental perspective and assess technical and economic solutions to minimize conflicts with wildlife and habitat conservation. Thus, the OPTIPOL rationale is based on the belief that the negative effects of electricity transmission and distribution can be reduced with respect to birds and mammals. OPTIPOL has several ambitious objectives, and is divided into sub-projects and specific tasks. From the first of November a PhD-student became part of the project, a position that will be held for 4 years. The main objective of the PhD-activities will be to assess how and why different wildlife species use deforested areas below power lines, evaluate possible positive and negative effects of power-line ROWs, and assess the possibilities for quality improvement. Another part of the project is dedicated the effects of linear structures on movement patterns and distribution in the landscape in native deer species. Here we will examine how different spatial scales influence the processes that guide movement patterns, and responses to linear structures. Another focus will be small game species, with mountain hare, capercaillie, black grouse and hazel grouse as model species. The main objective will be to assess the impact of transforming ROW habitats into attractive small-game foraging

  9. Solid State Sciences Committee (SSSC). Technical progress report, May 1, 1992--April 30, 1993

    Taylor, R.

    1995-01-01

    The Solid State Sciences Committee (SSSC) of the National Research Council (NRC) is charged with monitoring the health of the field of materials science in the United States. Accordingly, the Committee identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special forums are among the mechanisms used by the SSSC to meet its charge. This progress report presents a review of SSSC activities from May 1, 1992 through April 30, 1993. The details of prior activities are discussed in earlier reports. During the above period, the SSSC has continued to track and participate, when requested, in the development of a Federal initiative on advanced materials and processing. Specifically, the SSSC is presently planning the 1993 SSSC Forum (to be cosponsored with the National Materials Advisory Board (NMAB) and the Washington Materials Forum (WMF)). The thrust will be to highlight the Federal Advanced Materials and Processing Program (AMPP). In keeping with its charge to identify and highlight specific areas for scientific and technological opportunities, the SSSC continued to oversee the conduct of a study on biomolecular materials. Preliminary plans also were developed for a study on neutron science, however, further activity is pending. A proposed study on ultrasmall devices has been expanded and absorbed into a broader context; the BPA, with SSSC participation, is preparing to hold a program initiation meeting to evaluate the need for a study on information technology and hardware

  10. Advanced converter technology. Technical progress report, May 23, 1979-May 22, 1980

    Banic, C. V.; Eckhouse, S. A.; Kornbrust, F. J.; Lipman, K.; Peterson, J. L.; Rosati, R. W.

    1980-01-01

    The overall objective of this program is to define an advanced converter system employing 1980's technology in all subsystem and component areas for use in electrochemical energy storage systems. Additional experimental effort will validate elements of the advanced commutation circuitry on a full-scale breadboard basis. Improved models of battery electrical characteristics are beng defined and experimental apparatus is being designed to measure these characteristics and to enable better definition of the battery-power conditioner interface. Improvement of energy-storage system performance through modification of battery converter characteristics will also be investigated. During this first year of the contract, a new more advanced concept for power conditioning based on a concept defined by United Technologies Corporation for fuel cell use was evaluated. This high switching frequency concept has the potential for significantly reducing the size and cost of battery plant power conditioners. As a result, the Department of Energy authorized redirection of the program to first evaluate this new concept and then to reorient the program to adopt this concept as the primary one. Progress is reported. (WHK)

  11. Exploratory research on solvent refined coal liquefaction. Annual technical progress report, January 1-December 31, 1979

    None

    1980-09-01

    This report summarizes the progress of the Exploratory Research on Solvent Refined Coal Liquefaction project by The Pittsburg and Midway Coal Mining Co.'s Merriam Laboratory during 1979. In a series of experiments with varying feed gas composition, low levels (5 to 10 mole %) of carbon monoxide had little effect on the SRC II processing of Pittsburgh Seam coal (Powhatan No. 5 Mine) while higher levels (20 to 40 mole %) resulted in a general degradation of operability and reduced oil yields. Addition of finely divided (approx. 1 ..mu..m) pyrite to the reactive Powhatan coal had little effect on oil yields although the molecular weight of the distillation residue was apparently decreased. When finely divided pyrite and magnetite were added to the less reactive coals from the Loveridge and Blacksville No. 1 Mines (also Pittsburgh Seam), however, substantial increases in oil yields and product quality were obtained. In a comparison of upflow and downflow dissolver configurations with Powhatan coal in the SRC II mode, there was no difference in yields or product quality. A study characterizing specific reactors revealed a significantly higher conversion in the SRC I mode with a reactor approximating plug flow conditions compared to a completely backmixed reactor. In the SRC II mode there was only a slightly higher oil yield with the plug flow reactor.

  12. Ion rings for magnetic fusion. Technical progress report, August 1, 1993--June 1, 1994

    Sudan, R.N.

    1994-01-01

    In Our Proposal ''Ion Rings for Magnetic Fusion'' of January 6, 1993, Stage I of our Proposed Program plan (the 12 months) consisted of the following tasks: Experiments on the existing ion ring experimental system IREX to test a new magnetically-controlled anode plasma source (MAP) for the ion beam diode injector; numerical simulations of ion ring formation to optimize design parameters for the field reversed ion ring experiment (FIREX) to be built and operated in Stage II; and designing the power supply for the FIREX injector and the magnetic field system using results for A and B. During the past 7 1/2 months our work has progressed according to the above plan. In addition to testing the MAP diode on IREX we have tested the EMFAPS (evaporating metal film anode plasma source) anode on the Sandia National Laboratories funded LION pulsed power generator. As a result of these experiments, described this paper, we have arrived at the conclusion that EMFAPS anode for the ion at present because the MAP diode beam diode injector is our preferred choice for is still in an early stage of development

  13. Nuclear structure theory. Technical progress report, September 1, 1984-August 31, 1985

    French, J.B.; Koltun, D.S.

    1985-01-01

    This report summarizes progress in the following areas of research: Spectral Averaging, including the theory of level densities and partition functions for interacting nucleons, spectral distributions for fixed symmetries, general studies of distributions (in particular of strength distributions) considered as multivariate processes, and applications to the secular behavior of fluctuation measures; spectral and strength fluctuations, including study of the transitions between different fluctuation patterns (i.e., between different types of quantum chaos) as a conserved symmetry is gradually broken, application of these results to determining values of, or upper bounds for, the goodness of symmetries in complex nuclei, reduction of values or bounds to statements about the nuclear Hamiltonian, in particular for time-reversal symmetry, and specific studies of quantum chaos; statistical theory of pion absorption, including analysis of the (π,p) inclusive reaction; and quark theory of nuclear matter, involving development of models which show two limiting behaviors - that of a Fermi gas of nucleons (quark clusters) at low density and of a Fermi gas of quarks at high density. Both variational and exact solutions of one model have been found. 9 refs

  14. University of Colorado at Boulder Nuclear Physics Laboratory technical progress report

    Peterson, R.J.

    1991-01-01

    This report summarizes experimental work carried out between October 1, 1990, the closing of our Progress Report, and August 14, 1991 at the Nuclear Physics Laboratory of the University of Colorado, Boulder, under contract DE-FG02-ER40269 with the United States Department of Energy. This contract supports broadly based experimental work in intermediate energy nuclear physics. The program includes pion-nucleon studies at TRIUMF and LAMPF, inelastic pion scattering and charge exchange reactions at LAMPF, and nucleon charge exchange at LAMPF/NTOF. The first results of spin-transfer observables in the isovector (rvec p,rvec n) reaction are included in this report. Our data confirm the tentative result from (rvec p,rvec p') reactions that the nuclear isovector spin response shows neither longitudinal enhancement nor transverse queching. Our program in quasifree scattering of high energy pions shows solid evidence of isoscalar enhancement of the nuclear nonspin response. We include several comparisons of the quasifree scattering of different probes. Results from our efforts in the design of accelerator RF cavities are also included in this report

  15. Proton resonance spectroscopy. Quarterly technical progress report, December 1992--November 1995

    Shriner, J.F. Jr.

    1995-11-01

    Work on chaos in the low-lying levels of nuclei has continued on several fronts. The major effort has been study of the 29 Si(p,γ) reaction with the goal of establishing a complete level scheme for 30 P and analyzing the eigenvalue fluctuations for evidence of chaos. These measurements are in progress, and the current status is described. A related topic is the search for different signatures of chaos which do not require the extremely high degree of completeness and purity necessary for eigenvalue analyses; those efforts are discussed in Sections 2 and 3. The possibility of studying both parity violation and time-reversal invariance violation with charged particle resonances has been explored by performing calculations using experimentally measured resonance parameters. Large enhancements are indeed available; the results are discussed in Sections 4 and 5. Preparations for an experimental study of parity violation using these techniques are ongoing. An undergraduate project searching for experimental evidence of a parity dependence of level density is discussed in Section 6. A number of improvements to the operation of the TUNL KN accelerator have been implemented in the past three years. These are described in Section 7

  16. Proton resonance spectroscopy. Quarterly technical progress report, December 1992--November 1995

    Shriner, J.F. Jr.

    1995-11-01

    Work on chaos in the low-lying levels of nuclei has continued on several fronts. The major effort has been study of the {sup 29}Si(p,{gamma}) reaction with the goal of establishing a complete level scheme for {sup 30}P and analyzing the eigenvalue fluctuations for evidence of chaos. These measurements are in progress, and the current status is described. A related topic is the search for different signatures of chaos which do not require the extremely high degree of completeness and purity necessary for eigenvalue analyses; those efforts are discussed in Sections 2 and 3. The possibility of studying both parity violation and time-reversal invariance violation with charged particle resonances has been explored by performing calculations using experimentally measured resonance parameters. Large enhancements are indeed available; the results are discussed in Sections 4 and 5. Preparations for an experimental study of parity violation using these techniques are ongoing. An undergraduate project searching for experimental evidence of a parity dependence of level density is discussed in Section 6. A number of improvements to the operation of the TUNL KN accelerator have been implemented in the past three years. These are described in Section 7.

  17. Technical progress report for UTSI/CFFF MHD program completion and related activity

    Chapman, James N.; Muehlhauser, Joel W.

    1998-01-01

    Routine preventive maintenance of the DOE Coal Fired Flow Facility (CFFF) is being performed. Modernization programs, funded under subcontract from Foster Wheeler Development Corporation by the DOE HIPPS Program, have been completed on the coal processing system, the data acquisition and control system and the control room. Late in the quarter, all work was stopped on maintenance of the CFFF at DOE instruction. Environmental restoration actions continued with monitoring of groundwater wells and holding pond effluent. Progress is reported on the approved groundwater remediation plan. Actions are underway to dispose of spent seed/ash mixtures and excess coal remaining from the MHD POC program. The status of five (5) High Temperature Superconductor (HTS) projects is reported. A summary is included of the results attained with sol-gel experiments with buffer layers and YBCO. The status of the cost/performance study of electron beam and PLD deposition is pre-sented. A summary of work performed in diagnostics for real time control of HTS processes is presented

  18. TECHNICAL PROGRESS REPORT FOR UTSI/CFFF MHD PROGRAM COMPLETION AND RELATED ACTIVITIES

    DR. JAMES N. CHAPMAN; DR. JOEL W. MUEHLHAUSER

    1998-10-23

    Routine preventive maintenance of the DOE Coal Fired Flow Facility (CFFF) is being performed. Modernization programs, funded under subcontract from Foster Wheeler Development Corporation by the DOE HIPPS Program, have been completed on the coal processing system, the data acquisition and control system and the control room. Late in the quarter, all work was stopped on maintenance of the CFFF at DOE instruction. Environmental restoration actions continued with monitoring of groundwater wells and holding pond effluent. Progress is reported on the approved groundwater remediation plan. Actions are underway to dispose of spent seed/ash mixtures and excess coal remaining from the MHD POC program. The status of five (5) High Temperature Superconductor (HTS) projects is reported. A summary is included of the results attained with sol-gel experiments with buffer layers and YBCO. The status of the cost/performance study of electron beam and PLD deposition is pre-sented. A summary of work performed in diagnostics for real time control of HTS processes is presented.

  19. Technical progress report to the Department of Energy on the Solid State Sciences Committee (SSSC)

    1995-01-01

    The Solid State Sciences Committee (SSSC) of the National Research Council (NRC) is charged with monitoring the health of the field of materials science in the United States. Accordingly, the Committee identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special forums are among the mechanisms used by the SSSC to meet its charge. This progress report presents a review of SSSC activities from May 1, 1992 through April 30, 1993. The details of prior activities are discussed in earlier reports. During the above period, the SSSC has continued to track and participate, when requested, in the development of a Federal initiative on advanced materials and processing. Specifically, the SSSC is presently planning the 1993 SSSC Forum (to be cosponsored with the National Materials Advisory Board (NMAB) and the Washington Materials Forum (WNM)). The thrust will be to highlight the Federal Advanced Materials and Processing Program (AMPP). In keeping with its charge to identify and highlight specific areas for scientific and technological opportunities, the SSSC continued to oversee the conduct of a study on biomolecular materials. Preliminary plans also have been developed for studies on neutron scattering science, on ultrasmall devices, and on molecular routes to materials

  20. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

    Cottrell, W.B.; Klein, A.

    1977-02-23

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication.

  1. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol. 11, No. 1--Vol. 17, No. 6

    Cottrell, W.B.; Klein, A.

    1977-01-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970), through Vol. 17, No. 6 (Nov.-Dec. 1976). The index includes a chronological list of articles (including abstract) followed by KWIC and Author Indexes. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 350 technical articles in the last six years of publication

  2. ESTABLISHMENT OF THE CENTER FOR ADVANCED SEPARATION TECHNOLOGIES

    Hugh W. Rimmer

    2003-07-01

    Technical Progress Report describes progress made on the eight sub-projects awarded in the first year of Cooperative Agreement DE-FC26-01NT41091: Establishment of the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices. Due to the time taken up by the solicitation/selection process, these cover the initial 6-month period of activity only.

  3. Solvent refined coal (SRC) process. Quarterly technical progress report, January 1980-March 1980. [In process streams

    1981-01-01

    This report summarizes the progress of the Solvent Refined Coal (SRC) project at the SRC Pilot Plant in Fort Lewis, Wahsington, and the Process Development Unit (P-99) in Harmarville, Pennsylvania. After the remaining runs of the slurry preheater survey test program were completed January 14, the Fort Lewis Pilot Plant was shut down to inspect Slurry Preheater B and to insulate the coil for future testing at higher rates of heat flux. Radiographic inspection of the coil showed that the welds at the pressure taps and the immersion thermowells did not meet design specifications. Slurry Preheater A was used during the first 12 days of February while weld repairs and modifications to Slurry Preheater B were completed. Two attempts to complete a material balance run on Powhatan No. 6 Mine coal were attempted but neither was successful. Slurry Preheater B was in service the remainder of the quarter. The start of a series of runs at higher heat flux was delayed because of plugging in both the slurry and the hydrogen flow metering systems. Three baseline runs and three slurry runs of the high heat flux program were completed before the plant was shut down March 12 for repair of the Inert Gas Unit. Attempts to complete a fourth slurry run at high heat flux were unsuccessful because of problems with the coal feed handling and the vortex mix systems. Process Development Unit (P-99) completed three of the four runs designed to study the effect of dissolver L/D ratio. The fourth was under way at the end of the period. SRC yield correlations have been developed that include coal properties as independent variables. A preliminary ranking of coals according to their reactivity in PDU P-99 has been made. Techniques for studying coking phenomenona are now in place.

  4. LMFBR flexible pipe joint development program. Annual technical progress report, government fiscal year 1977

    1978-01-01

    Currently, the ASME Boiler and Pressure Vessel Code does not allow the use of flexible pipe joints (bellows) in Section III, Class 1 reactor primary piping systems. Studies have shown that the primary piping loops of LMFBR's could be simplified by using these joints. This simplification translates directly into shorter primary piping runs and reduced costs for the primary piping system. Further cost savings result through reduced vault sizes and reduced containment building diameter. In addition, the use of flexible joints localizes the motions from thermally-induced piping growth into components which are specifically designed to accommodate this motion. This reduces the stress levels in the piping system and its components. It is thus economically and structurally important that flexible piping joints be available to the LMFBR designer. The overall objective of the Flexible Joint Program is to provide this availability. This will be accomplished through the development of ASME rules which allow the appropriate use of such joints in Section III, Class 1 piping systems and through the development and demonstration of construction methods which satisfy these rules. The rule development includes analytic and testing methodology formulations which will be supported by subscale bellows testing. The construction development and demonstration encompass the design, fabrication, and in-sodium testing of prototypical LMFBR plant-size flexible pipe joints which meet all ASME rule requirements. The satisfactory completion of these developmental goals will result in an approved flexible pipe joint design for the LMFBR. Progress is summarized in the following efforts undertaken during 1977 to accomplish these goals: (1) code case support, (2) engineering and design, (3) material development, (4) testing, and (5) manufacturing development

  5. Advanced thermally stable jet fuels: Technical progress report, October 1994--December 1994

    Schobert, H.H.; Eser, S.; Song, C.; Hatcher, P.G.; Boehman, A.; Coleman, M.M.

    1995-02-01

    There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation in a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Characterization of solid gums, sediments, and carbonaceous deposits, is subtask, Studies of surface chemistry of PX-21 activated carbon during thermal degradation of jet A-1 fuel and n-dodecane; under Task 4, Coal-based fuel stabilization studies, is subtask, Exploratory screening and development potential of jet fuel thermal stabilizers over 400 C; and under Task 5, Exploratory studies on the direct conversion of coal to high quality jet fuels, are 4 subtasks: Novel approaches to low-severity coal liquefaction and coal/resid co-processing using water and dispersed catalysts; Shape-selective naphthalene hydrogenation for production of thermally stable jet fuels; Design of a batch mode and a continuous mode three-phase reactor system for the liquefaction of coal and upgrading of coal liquids; and Exploratory studies on coal liquids upgrading using mesopores molecular sieve catalysts. 136 refs., 69 figs., 24 tabs.

  6. Directional backlight liquid crystal autostereoscopic display: technical challenges, research progress, and prospect (Conference Presentation)

    Fan, Hang; Li, Kunyang; Zhou, Yangui; Liang, Haowen; Wang, Jiahui; Zhou, Jianying

    2016-09-01

    Recent upsurge on virtual and augmented realities (VR and AR) has re-ignited the interest to the immerse display technology. The VR/AR technology based on stereoscopic display is believed in its early stage as glasses-free, or autostereoscopic display, will be ultimately adopted for the viewing convenience, visual comfort and for the multi-viewer purposes. On the other hand, autostereoscopic display has not yet received positive market response for the past years neither with stereoscopic displays using shutter or polarized glasses. We shall present the analysis on the real-world applications, rigid user demand, the drawbacks to the existing barrier- and lenticular lens-based LCD autostereoscopy. We shall emphasize the emerging autostereoscopic display, and notably on directional backlight LCD technology using a hybrid spatial- and temporal-control scenario. We report the numerical simulation of a display system using Monte-Carlo ray-tracing method with the human retina as the real image receiver. The system performance is optimized using newly developed figure of merit for system design. The reduced crosstalk in an autostereoscopic system, the enhanced display quality, including the high resolution received by the retina, the display homogeneity without Moiré- and defect-pattern, will be highlighted. Recent research progress including a novel scheme for diffraction-free backlight illumination, the expanded viewing zone for autostereoscopic display, and the novel Fresnel lens array to achieve a near perfect display in 2D/3D mode will be introduced. The experimental demonstration will be presented to the autostereoscopic display with the highest resolution, low crosstalk, Moiré- and defect- pattern free.

  7. Theory of high-energy-collision processes. Technical progress report, January 1-December 31, 1981

    1982-01-01

    Progress is described in the following areas: (1) several years ago, surprisingly simple expressions were obtained for the differential cross sections of e + e - → μ + μ - γ and e + e - → e + e - γ at high energies. Such simple expressions were generalized to twelve other similar radiative processes in QED and QCD. Afterwards, it was found that these results can be derived easily with the help of helicity amplitudes. This method is being investigated for many other radiative processes; (2) in the two-dimensional Ising model, the horizontal and vertical interaction energies are usually taken to be different. When this idea of different interactions in different directions is applied to the Z 2 lattice gauge theory in four dimensions, a limiting case is found which is exactly solvable. Contrary to numerical calculations at the symmetry point, the phase transition is found to be of second order; (3) on the subject of supersymmetry, general helicity and spin sum rules were obtained for massless and massive supermultiplets, and a functional integral approach was found as a natural setting for Witten's criterion for the occurrence of dynamic symmetry breaking of supersymmetry. A systematic and exhaustive analysis of explicit soft breaking of global supersymmetry has also been carried out using the methods of superfields; (4) the renormalization of the massless Thirring model in the neighborhood of g = -π/2 was studied. The results are consistent with those found previously by placing the model on a lattice; and (5) in studying the effect of laboratory temperature on scattering processes, it was found that transport phenomena play an important role. As a preparation for this study, an exactly solvable case of the nonlinear Boltzmann equation has been found and studied

  8. Improved methods for water shutoff. Final technical progress report, October 1, 1997--September 30, 1998

    Seright, R.S.; Liang, J.T.; Schrader, R.; Hagstrom, J. II; Liu, J.; Wavrik, K.

    1998-10-01

    In the United States, more than 20 billion barrels of salt water are produced each year during oilfield operations. A tremendous economic incentive exists to reduce water production if that can be accomplished without significantly sacrificing hydrocarbon production. This three-year research project had three objectives. The first objective was to identify chemical blocking agents that will (a) during placement, flow readily through fractures without penetrating significantly into porous rock and with screening out or developing excessive pressure gradients and (b) at a predictable and controllable time, become immobile and resistant breakdown upon exposure to moderate to high pressure gradients. The second objective was to identify schemes that optimize placement of the above blocking agents. The third objective was to explain why gels and other chemical blocking agents reduce permeability to one phase (e.g., water) more than that to another phase (e.g., oil or gas). The authors also wanted to identify conditions that maximize this phenomenon. This project consisted of three tasks, each of which addressed one of the above objectives. This report describes work performed during the third and final period of the project. During this three-year project, they: (1) Developed a procedure and software for sizing gelant treatments in hydraulically fractured production wells; (2) Developed a method (based on interwell tracer results) to determine the potential for applying gel treatments in naturally fractured reservoirs; (3) Characterized gel properties during extrusion through fractures; (4) Developed a method to predict gel placement in naturally fractured reservoirs; (5) Made progress in elucidating the mechanism for why some gels can reduce permeability to water more than that to oil; (6) Demonstrated the limitations of using water/oil ratio diagnostic plots to distinguish between channeling and coning; and (7) Proposed a philosophy for diagnosing and attacking water

  9. GPHS-RTGs in support of the Cassini RTG Program. Semi annual technical progress report, September 26, 1994--April 2, 1995

    1995-01-01

    The technical progress achieved during the period 26 September 1994 through 2 April 1995 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described herein. Monthly technical activity for the period 27 February 1995 through 2 April 1995 is included in this progress report. The report addresses tasks, including: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG Fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds)

  10. International Power Institute`s quarterly technical progress report, July--September 1998

    Coles, J.E.

    1998-10-30

    The International Power Institute (IPI) at Morehouse College has organized a team to design and create a Short Term Training Program for ESKOM Union Leaders which will last four weeks and take place at a location in South Africa to be designated by ESKOM. This proposal envisions a group of no more than 25 union leaders to be trained at the same time but the program could be expanded to accommodate up to 40 trainees. The program is designed around interactive training with lectures followed by discussion, case studies, trainee work groups, homework assignments and two field study visits. Also, the program is designed to have a number of ESKOM management people join the course for one day in the second week and one day at the end, in each case after a half day of preparation in separate sessions from the union leaders, to share with the trainees expectations and, at the end of the program, their course experiences. In addition, IPI has prepared a follow on proposal for a Long Term Training Program. This LT program is specified in less detail but can be expanded based on future discussions with ESKOM management. The training program is designed with the following objectives: determine and identify the most pressing problems facing ESKOM Union Leadership in their relationship with management; instill in the union leadership a heightened sense of purpose and willingness to take ownership of a process that will increase effective outcomes of meaningful, good faith bargaining; develop skills and experience leading to improved union administration; enhance realistic expectations and improve process knowledge to facilitate future labor negotiations and grievance proceedings; and provide participants with enhanced skills and knowledge to develop and/or strengthen a functioning, democratic work culture and structure internal to the union.

  11. Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility; FINAL

    Thomas B. Kirchner

    2002-01-01

    The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

  12. Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility

    Kirchner, Thomas B.

    2002-01-01

    The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

  13. Savannah River Ecology Laboratory Annual Technical Progress Report of Ecological Research, June 30, 2001

    Bertsch, Paul M.; Janecek, Laura; Rosier, Brenda

    2001-06-30

    The Savannah River Ecology Laboratory (SREL) is a research unit of the University of Georgia (UGA) and has been conducting ecological research on the Savannah River Site (SRS) in South Carolina for 50 years. The overall mission of the Laboratory is to acquire and communicate knowledge of ecological processes and principles. SREL conducts fundamental and applied ecological research, as well as education and outreach programs, under a Cooperative Agreement with the U.S. Department of Energy (DOE) SRS near Aiken, South Carolina. The Laboratory's research mission during the 2001 fiscal year was fulfilled with the publication of one book and 83 journal articles and book chapters by faculty, technical staff, students, and visiting scientists. An additional 77 journal articles have been submitted or are in press. Other noteworthy events took place as faculty members and graduate students received awards. These are described in the section Special Accomplishments of Faculty, Staff, Students, and Administration on page 54. Notable scientific accomplishments include work conducted on contaminant transport, global reptile decline, phytoremediation, and radioecology. Dr. Domy Adriano authored the second edition of his book ''Trace Elements in Terrestrial Environments: Biogeochemistry, Bioavailability, and Risks of Metals'', which was recently published by Springer-Verlag. The book provides a comprehensive treatment of many important aspects of trace elements in the environment. The first edition of the book, published in 1986, has become a widely acclaimed and cited reference. International attention was focused on the problem of reptile species decline with the publication of an article on this topic in the journal ''Bioscience'' in August, 2000. The article's authors included Dr. Whit Gibbons and a number of other SREL herpetologists who researched the growing worldwide problem of decline of reptile species. Factors related

  14. Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility

    Thomas B. Kirchner

    2002-03-22

    The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

  15. KINETICS OF SLURRY PHASE FISCHER-TROPSCH SYNTHESIS. FOURTH ANNUAL TECHNICAL PROGRESS REPORT

    Bukur, Dragomir B.; Froment, Gilbert F.; Olewski, Tomasz

    2006-01-01

    This report covers the fourth year of a research project conducted under the University Coal Research Program. The overall objective of this project is to develop a comprehensive kinetic model for slurry-phase Fischer-Tropsch synthesis (FTS) employing iron-based catalysts. This model will be validated with experimental data obtained in a stirred-tank slurry reactor (STSR) over a wide range of process conditions. The model will be able to predict molar flow rates and concentrations of all reactants and major product species (water, carbon dioxide, linear 1- and 2-olefins, and linear paraffins) as a function of reaction conditions in the STSR. During the fourth year of the project, an analysis of experimental data collected during the second year of this project was performed. Kinetic parameters were estimated utilizing product distributions from 27 mass balances. During the reporting period two kinetic models were employed: a comprehensive kinetic model of Dr. Li and co-workers (Yang et al., 2003) and a hydrocarbon selectivity model of Van der Laan and Beenackers (1998, 1999) The kinetic model of Yang et al. (2003) has 24 parameters (20 parameters for hydrocarbon formation, and 4 parameters for the water-gas-shift (WGS) reaction). Kinetic parameters for the WGS reaction and FTS synthesis were estimated first separately, and then simultaneously. The estimation of these kinetic parameters employed the Levenberg-Marquardt (LM) method and the trust-region reflective Newton large-scale (LS) method. A genetic algorithm (GA) was incorporated into estimation of parameters for FTS reaction to provide initial estimates of model parameters. All reaction rate constants and activation energies were found to be positive, but at the 95% confidence level the intervals were large. Agreement between predicted and experimental reaction rates has been fair to good. Light hydrocarbons are predicted fairly accurately, whereas the model underpredicts values of higher molecular weight

  16. I-NERI QUARTERLY TECHNICAL PROGRESS REPORT - JANUARY 1 - MARCH 31, 2005

    Chang Oh

    2005-01-01

    codes. The three categories of experiments were performed in the facility; (1) upper pool cooling trip test, (2) LOFC experiment, (3) emissivity measurement experiment. (C) Prof. NO continued Task 3. (Prof NO) The experimental work of air ingress is going on without any concern: Geometry and size effect test has been completed. The conversion factor for internal surface area was obtained through this experiment. Burn-off test was performed and the uniformity of internal reaction was confirmed. (D) INEEL engineers continued to extend the diffusion model for multiple chemical species and made some calculations. (E) Prof. Lee and Martin at University of Michigan continued to analyze the effect of the stochastic fuel on the neutronic analysis and have initiated fuel depletion calculations for the VHTGR core. Progress during the past quarter includes: Further analysis of stochastic fuel geometry; Preliminary Monte Carlo depletion of full-core VHTGR; and Installation of MCNP5 on Unix cluster

  17. Optimal design and routing of power lines; ecological, technical and economic perspectives (OPTIPOL). Progress report 2012

    Bevanger, Kjetil; Bartzke, Gundula; Broeseth, Henrik; Dahl, Espen Lie; Gjershaug, Jan Ove; Hanssen, Frank; Jacobsen, Karl-Otto; Kleven, Oddmund; Kvaloey, Paal; May, Roel; Meaas, Roger; Nygaaard, Torgeir; Resnaes, Steinar; Stokke, Sigbjoern; Thomassen, Joern

    2012-07-01

    birds in the database, compared to only 117 a year earlier. WP5 - 'A Least Cost Path (LCP) toolbox for optimal route routing of power lines', has developed an LCP-pilot to demonstrate the LCP method, based on the impact studies were undertaken prior to construction of a 420 kV transmission line in Central Norway 2005. Relevant economic, ecological and technological environment criteria based on suggestions from interested users (NGOs, government, industry, etc.), was used. LCP-pilot and a fuzzy-logic approach of this was demonstrated in the first dialogue-based workshop, 23.-24. april 2012. The seminar, which had an emphasis on criteria definitions were followed up with a working seminar that focused criterion values ??on 20 november 2012. Lecture - 'A Least Cost Path (LCP) Toolbox for Optimal Routing of Power Lines, -was presented and submitted as contributions to the conference report from 'The 10th ROW Conference' in Arizona, 'The 32nd Annual Conference of the International Association for Impact Assessment (IAIA12) ' in Porto, Portugal, and 'The ESRI European User Conference' in Oslo. WP6 - 'Birds and camouflaging of power lines', has almost completed the final report, 'Power line camouflaging. An assessment of the ecological and technical challenges'. 'Because of the budget situation in CEDREN However, completion of the report postponed until the end of April 2013. WP7 - 'Effect of line marking / modifications remedial measures against bird mortality' has almost completed the final report 'Opportunities and limitations in terms of reducing mortality in birds due to collision and electrocution.' Due to overall budget situation in CEDREN the report deferred to the end of april 2013. WP8, 'guidelines for technological solutions that may reduce mortality in birds because of the power line's', has focused topics relating to the labeling, design, insulation, camouflage and wiring. The results, which are presented in the notes and articles, will be implemented in

  18. Major Oil Plays in Utah and Vicinity. Quarterly Technical Progress Report

    Thomas C. Chidsey; Craig D. Morgan; Kevin McClure; Douglas A. Sprinkel; Roger L. Bon; Hellmut H. Doelling

    2003-01-01

    overlying argillaceous and non-fractured units. The best outcrop analogs for Twin Creek reservoirs are found at Devils Slide and near the town of Peoa, Utah, where fractures in dense, homogeneous non-porous limestone beds are in contact with the basal siltstone units (containing sealed fractures) of the overlying units. The shallow marine, Mississippian Leadville Limestone is a major oil and gas reservoir in the Paradox Basin of Utah and Colorado. Hydrocarbons are produced from basement-involved, northwest-trending structural traps with closure on both anticlines and faults. Excellent outcrops of Leadville-equivalent rocks are found along the south flank of the Uinta Mountains, Utah. For example, like the Leadville, the Mississippian Madison Limestone contains zones of solution breccia, fractures, and facies variations. When combined with subsurface geological and production data, these outcrop analogs can improve (1) development drilling and production strategies such as horizontal drilling, (2) reservoir-simulation models, (3) reserve calculations, and (4) design and implementation of secondary/tertiary oil recovery programs and other best practices used in the oil fields of Utah and vicinity. In the southern Green River Formation play of the Uinta Basin, optimal drilling, development, and production practices consist of: (1) owning drilling rigs and frac holding tanks; (2) perforating sandstone beds with more than 8 percent neutron porosity and stimulate with separate fracture treatments; (3) placing completed wells on primary production using artificial lift; (4) converting wells relatively soon to secondary waterflooding maintaining reservoir pressure above the bubble point to maximize oil recovery; (5) developing waterflood units using an alternating injector--producer pattern on 40-acre (16-ha) spacing; and (6) recompleting producing wells by perforating all beds that are productive in the waterflood unit. As part of technology transfer activities during this quarter

  19. Feed-in tariffs versus quotas: how to promote renewable s and stimulate technical progress for cost decrease?

    Menanteau, Ph.; Finon, D.; Lamy, M.L.

    2002-01-01

    Incentive schemes for the development of renewable energy sources may focus on quantities (defining national targets and setting up bidding systems, or quota systems providing for green certificate trading), or they may focus on prices (feed-in tariffs). Whatever the system chosen, the role of the public authorities is quite specific: to stimulate technical progress and speed up the technological learning processes so that ultimately renewable energy technologies will be able to compete with conventional technologies, once the environmental costs have been internalized. A comparison of instruments must thus take into account the characteristics of the innovation process and adoption conditions (uncertainties regarding cost curves, learning effects) which means also looking at dynamic efficiency criteria. The paper concludes that a system of feed-in tariffs is more efficient than a bidding system, but highlights the theoretical interest of green certificate trading which must be confirmed through practice, given the influence of market structures and rules on the performance of this type of approach. (author)

  20. Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

    Zhai, Shiyan; Song, Genxin; Qin, Yaochen; Ye, Xinyue; Lee, Jay

    2017-01-01

    This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June) led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

  1. Modeling the impacts of climate change and technical progress on the wheat yield in inland China: An autoregressive distributed lag approach.

    Shiyan Zhai

    Full Text Available This study aims to evaluate the impacts of climate change and technical progress on the wheat yield per unit area from 1970 to 2014 in Henan, the largest agricultural province in China, using an autoregressive distributed lag approach. The bounded F-test for cointegration among the model variables yielded evidence of a long-run relationship among climate change, technical progress, and the wheat yield per unit area. In the long run, agricultural machinery and fertilizer use both had significantly positive impacts on the per unit area wheat yield. A 1% increase in the aggregate quantity of fertilizer use increased the wheat yield by 0.19%. Additionally, a 1% increase in machine use increased the wheat yield by 0.21%. In contrast, precipitation during the wheat growth period (from emergence to maturity, consisting of the period from last October to June led to a decrease in the wheat yield per unit area. In the short run, the coefficient of the aggregate quantity of fertilizer used was negative. Land size had a significantly positive impact on the per unit area wheat yield in the short run. There was no significant short-run or long-run impact of temperature on the wheat yield per unit area in Henan Province. The results of our analysis suggest that climate change had a weak impact on the wheat yield, while technical progress played an important role in increasing the wheat yield per unit area. The results of this study have implications for national and local agriculture policies under climate change. To design well-targeted agriculture adaptation policies for the future and to reduce the adverse effects of climate change on the wheat yield, climate change and technical progress factors should be considered simultaneously. In addition, adaptive measures associated with technical progress should be given more attention.

  2. Preparation of a technology development roadmap for the Accelerator Transmutation of Waste (ATW) System : report of the ATW separations technologies and waste forms technical working group

    Collins, E.; Duguid, J.; Henry, R.; Karell, E.J.; Laidler, J.J.; McDeavitt, S.M.; Thompson, M.; Toth, L.M.; Williamson, M.; Willit, J.L.

    1999-01-01

    In response to a Congressional mandate to prepare a roadmap for the development of Accelerator Transmutation of Waste (ATW) technology, a Technical Working Group comprised of members from various DOE laboratories was convened in March 1999 for the purpose of preparing that part of the technology development roadmap dealing with the separation of certain radionuclides for transmutation and the disposal of residual radioactive wastes from these partitioning operations. The Technical Working Group for ATW Separations Technologies and Waste Forms completed its work in June 1999, having carefully considered the technology options available. A baseline process flowsheet and backup process were identified for initial emphasis in a future research, development and demonstration program. The baseline process combines aqueous and pyrochemical processes to permit the efficient separation of the uranium, technetium, iodine and transuranic elements from the light water reactor (LWR) fuel in the head-end step. The backup process is an all- pyrochemical system. In conjunction with the aqueous process, the baseline flowsheet includes a pyrochemical process to prepare the transuranic material for fabrication of the ATW fuel assemblies. For the internal ATW fuel cycle the baseline process specifies another pyrochemical process to extract the transuranic elements, Tc and 1 from the ATW fuel. Fission products not separated for transmutation and trace amounts of actinide elements would be directed to two high-level waste forms, one a zirconium-based alloy and the other a glass/sodalite composite. Baseline cost and schedule estimates are provided for a RD and D program that would provide a full-scale demonstration of the complete separations and waste production flowsheet within 20 years

  3. Preparation of a technology development roadmap for the Accelerator Transmutation of Waste (ATW) System : report of the ATW separations technologies and waste forms technical working group.

    Collins, E.; Duguid, J.; Henry, R.; Karell, E.; Laidler, J.; McDeavitt, S.; Thompson, M.; Toth, M.; Williamson, M.; Willit, J.

    1999-08-12

    In response to a Congressional mandate to prepare a roadmap for the development of Accelerator Transmutation of Waste (ATW) technology, a Technical Working Group comprised of members from various DOE laboratories was convened in March 1999 for the purpose of preparing that part of the technology development roadmap dealing with the separation of certain radionuclides for transmutation and the disposal of residual radioactive wastes from these partitioning operations. The Technical Working Group for ATW Separations Technologies and Waste Forms completed its work in June 1999, having carefully considered the technology options available. A baseline process flowsheet and backup process were identified for initial emphasis in a future research, development and demonstration program. The baseline process combines aqueous and pyrochemical processes to permit the efficient separation of the uranium, technetium, iodine and transuranic elements from the light water reactor (LWR) fuel in the head-end step. The backup process is an all- pyrochemical system. In conjunction with the aqueous process, the baseline flowsheet includes a pyrochemical process to prepare the transuranic material for fabrication of the ATW fuel assemblies. For the internal ATW fuel cycle the baseline process specifies another pyrochemical process to extract the transuranic elements, Tc and 1 from the ATW fuel. Fission products not separated for transmutation and trace amounts of actinide elements would be directed to two high-level waste forms, one a zirconium-based alloy and the other a glass/sodalite composite. Baseline cost and schedule estimates are provided for a RD&D program that would provide a full-scale demonstration of the complete separations and waste production flowsheet within 20 years.

  4. Novel ceramic-polymer composite membranes for the separation of hazardous liquid waste. 1998 annual progress report

    Cohen, Y.

    1998-01-01

    'This report summarizes the work progress over the last 1.75 years of a 3 year project. The objectives of the project have been to develop a new class of ceramic-supported polymeric membranes that could be tailored-designed for a wide-range of applications in remediation and pollution prevention. To date, a new class of chemically-modified ceramic membranes was developed for the treatment of oil-in-water emulsions and for the pervaporation removal of volatile organics from aqueous systems. These new ceramic-supported polymer (CSP) membranes are fabricated by modifying the pore surface of a ceramic membrane support by a graft polymerization process (Chaimberg and Cohen, 1994). The graft polymerization process consists of activating the membrane surface with alkoxy vinyl silanes onto which vinyl monomers are added via free-radical graft polymerization resulting in a thin surface layer of terminally anchored polymer chains. Reaction conditions are selected based on knowledge of the graft polymerization kinetics for the specific polymer/substrate system. The resultant ceramic-supported polymer (CSP) membrane is a composite structure in which mechanical strength is provided by the ceramic support and the selectivity is determined by the covalently bonded polymer brush layer. Thus, one of the unique attributes of the CSP membrane is that it can be used in environments where the polymer layer is swollen (or even completely miscible) in the mixture to be separated (Castro et al., 1993). It is important to note that the above modification process is carried out under mild conditions (e.g., temperature of about 70 C) and is well suited for large scale commercial application. In a series of studies, the applicability of a polyvinylpyrrolidone CSP membrane was demonstrated for the treatment of oil-in-water emulsion under a variety of flow conditions (Castro et al.,1996). Improved membrane performance was achieved due to minimization of surface adsorption of the oil components

  5. 1996 technical progress report

    1997-01-01

    Summaries of the researches are grouped into programs as follows: research and development in food and agriculture; research and development in health, environment and industry which includes all the PNRI research projects in 1996; scientific and technological services; and the nuclear regulations, licensing and safeguards of the institute

  6. 1997 technical progress report

    NONE

    1998-07-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards.

  7. Annual technical progress report

    1980-01-01

    During the present contract period Phaedrus has begun operation as a true tandem mirror. This was accomplished by achieving the rf sustained mode in which the plug densities were built up by a combination of central cell gas puffing and plug ICRH following stream gun turn off. It was demonstrated that the tandem mirror plasma could be sustained by plug ICRH for up to 1 msec following decay of the external plasma. In this mode plasma characteristics were no longer dominated by problems associated with a high conductivity stream gun plasma in the external region (as was the case in many previous experiments in Phaedrus). Among these problems were (1) line tying which significantly reduced instabilities in a way that would not apply to reactors and (2) low electron temperatures which had been held to approx. 20 eV

  8. 1999 technical progress report

    2000-01-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards

  9. 1999 technical progress report

    NONE

    2000-07-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards.

  10. 1996 technical progress report

    NONE

    1998-12-31

    Summaries of the researches are grouped into programs as follows: research and development in food and agriculture; research and development in health, environment and industry which includes all the PNRI research projects in 1996; scientific and technological services; and the nuclear regulations, licensing and safeguards of the institute.

  11. 1997 technical progress report

    1998-01-01

    This report presents the on-going research and development projects of the Philippine Nuclear Research Institute (PNRI) in the fields of agriculture, environment and industry, scientific and technological services and nuclear regulations, licensing and safeguards

  12. Final Technical Progress Report

    J.Y. Hwang; R.C. Greenlund

    2002-12-31

    Michigan Technological University has demonstrated major inroads in establishing the viability of utilizing aluminum smelting by-product waste materials in lightweight concrete product applications. The research identified key elements of producing various forms of lightweight concrete products through utilizing various procedures and mixture components with the by-product materials. A process was developed through pilot plant testing that results in additional aluminum recovery at finer sizes, a clean returnable salt product through spray drying technology, and a low-salt-content oxide product with enough aluminum metal content that it can be used to form lightweight cementitious mixtures. Having three distinct products aids in generating favorable process economics. Revenue projections from aluminum recovery and salt recovery are enough to cover processing costs and create a cost-free oxide product to market for lightweight concrete applications. This supply side commercialization strategy offers aluminum by-product recyclers a potentially no cost product, which has been demonstrated through this project to create desirable and marketable lightweight concrete products of various forms. Environmental benefits to the public are tremendous. At best, all dross and salt cake materials have the potential to be completely recycled and utilized. At worst, disposal sites would see a reduced amount of material: a post processed oxide product with little salt and no hydrogen sulfide or ammonia gas generating capability, which, if isolated from high alkali conditions, would pose no reactivity concerns. The US aluminum industry has historically, along with the steel industry, been a leader in recycling metal. The findings from this project, increased metal recovery, improved salt recycling, and demonstrated end uses for oxide residues, will go a long way in helping the aluminum industry obtain 100% material utilization and zero discharge.

  13. 1995 technical progress report

    1997-01-01

    Summaries of the researches are grouped into programs as follows: research and development which covers all the PNRI research projects in 1994; scientific and technological services; and the nuclear regulations, licensing and safeguards of the institute

  14. Technical Progress Report

    Paul D. Ronney

    2004-08-26

    An ignition source was constructed that is capable of producing a pulsed corona discharge for the purpose of igniting mixtures in a test chamber. The corona generator can also be used as the ignition source for one cylinder on a test engine. The first tests were performed in a cylindrical shaped chamber to study the characteristics of the corona and analyze various electrode geometries. Next a test chamber was constructed that closely represented the dimensions of the combustion chamber of the test engine at USC. Combustion tests were performed in this chamber and various electrode diameters and geometries were tested. Higher peak pressures and faster pressure rise times were realized consistently in all test chambers versus standard spark plug ignition. A test engine was purchased for the project that has two spark plug ports per cylinder to The data acquisition and control system hardware for the USC engine lab was updated with new equipment. New software was also developed to perform the engine control and data acquisition functions including cylinder pressure monitoring. A ceramic corona electrode has been designed that fits in the new test engine and is capable of withstanding the pressures and temperatures encountered inside the combustion chamber. The corona ignition system was tested on the engine and an increase in both peak pressure and IMEP were seen in the initial test. There are issues that must be addressed before on-engine testing can continue such as EMF interference from the corona generator and electrical insulation on portions of the piston and cylinder head to prevent arcing. The EMF issue can be solved with proper shielding and grounding and various ceramic coatings are being researched for electrical insulation.

  15. Technical Progress Report

    Engelhardt, G.R.; MacDonald, D.D.

    1999-01-01

    During the past quartile (two month period) most attention has been concentrated on the problem of definition critical temperature at which ''wet'' corrosion first became operable. It has been shown that, in principle, ''wet'' corrosion processes can not be ignored for Yucca Mountain, even for initial times, when the temperature of the surface of containers is well above the boiling temperature of water for the prevailing conditions. This is because the surfaces are covered by highly hydrophilic oxides (e.g. Fe 2 O 3 , NiO, Cr 2 O 3 ) that will hydrate to the form of corresponding hydroxides, which are proton conductors, at least when in the ''wet'' condition. Because proton conduction and the presence of ''bound'' water are all that are required for the external environment to support metallic corrosion in either its general or localized form. Thus, the temperature of dehydration of the hydroxide, e.g. M(OH) 2 → MO + H 2 O(g), is a better criterion for the upper temperature limit for ''wet'' corrosion than is the boiling temperature of ''bulk'' water. During this first task, we have reviewed the existing thermodynamic data base for the dehydration of metal hydroxides and analytical expressions have been developed that allow the upper temperature limit to be estimated

  16. Technical Status Report on the Effect of Phosphate and Aluminum on the Development of Amorphous Phase Separation in Sodium

    Cozzi, A.D.

    1998-01-01

    The objective of the Tank Focus Area ''Optimize Waste Loading'' task is to enhance the definition of the acceptable processing window for high-level waste vitrification plants. One possible manner in which the acceptable processing window may be enhanced is by reducing the uncertainty of various compositional/property models through a specifically defined experimental plan. A reduction in model uncertainty can reduce limitations on current acceptance constraints and may allow for a larger processing or operational window. Enhanced composition/property model predictions coupled with an increased waste loading may decrease the processing time and waste glass disposal costs (i.e., overall lifecycle costs). One of the compositional/property models currently being evaluated by the Tanks Focus Area is related to the development of amorphous phase separation in multi-component borosilicate glasses.Described in this report is the current status for evaluating the effect of phosphorus and alumina on both simple sodium borosilicate and high-level waste glasses on the formation of amorphous phase separation. The goal of this subtask is to increase the understanding of the formation of phase separation by adding significant amounts (3-5 wt. percent) of phosphorus and alumina to well-characterized glasses. Additional scope includes evaluating the effects of thermal history on the formation of amorphous phase separation and durability of select glasses.The development of data, understanding, and quantitative description for composition and kinetic effects on the development of amorphous phase separation will continue in FY99. This effort will provide insight into the compositional and thermal effects on phase stability and will lead to a better understanding of the methods used to predict the development of amorphous phase separation in HLW glasses

  17. Technical Note: Interleaved Bipolar Acquisition and Low-rank Reconstruction for Water-Fat Separation in MRI.

    Cho, JaeJin; Park, HyunWook

    2018-05-17

    To acquire interleaved bipolar data and reconstruct the full data using low-rank property for water fat separation. Bipolar acquisition suffers from issues related to gradient switching, the opposite gradient polarities, and other system imperfections, which prevent accurate water-fat separation. In this study, an interleaved bipolar acquisition scheme and a low-rank reconstruction method were proposed to reduce issues from the bipolar gradients while achieving a short imaging time. The proposed interleaved bipolar acquisition scheme collects echo-time signals from both gradient polarities; however, the sequence increases the imaging time. To reduce the imaging time, the signals were subsampled at every dimension of k-space. The low-rank property of the bipolar acquisition was defined and exploited to estimate the full data from the acquired subsampled data. To eliminate the bipolar issues, in the proposed method, the water-fat separation was performed separately for each gradient polarity, and the results for the positive and negative gradient polarities were combined after the water-fat separation. A phantom study and in-vivo experiments were conducted on a 3T Siemens Verio system. The results for the proposed method were compared with the results of the fully sampled interleaved bipolar acquisition and Soliman's method, which was the previous water-fat separation approach for reducing the issues of bipolar gradients and accelerating the interleaved bipolar acquisition. The proposed method provided accurate water and fat images without the issues of bipolar gradients and demonstrated a better performance compared with the results of the previous methods. The water-fat separation using the bipolar acquisition has several benefits including a short echo-spacing time. However, it suffers from bipolar-gradient issues such as strong gradient switching, system imperfection, and eddy current effects. This study demonstrated that accurate water-fat separated images can

  18. Laser isotope separation by selective excited state photochemistry. Annual progress report, March 31, 1976--February 28, 1977

    Zare, R.N.

    1977-03-01

    Experimental results are presented providing insight into the mechanisms of photochemical separation of Cd isotopes by selective excitation of ICl in the presence of halogenated olefins. The types of scrambling reactions that can be expected in isotope separation by scavenging are discussed along with strategies for minimizing such reactions. The experimental results are summarized and the reaction mechanisms are represented by graphic equations

  19. Superconducting open-gradient magnetic separation for the pretreatment of radioactive or mixed waste vitrification feeds. 1998 annual progress report

    Crawford, C.; Doctor, R.D.; Landsberger, S.; Nunez, L.; Ritter, J.

    1998-01-01

    'The objective is to reduce the volume and cost of high-level waste glass produced during US DOE remediation activities by demonstrating that magnetic separation can separate crystalline, amorphous, and colloidal constituents in vitrification feed streams known to be deleterious to the production of borosilicate glass. Magnetic separation will add neither chemicals nor generate secondary waste streams. The project includes the systematic study of magnetic interactions of waste constituents under controlled physical and chemical conditions (e.g., hydration, oxidation, temperature) to identify mechanisms that control the magnetic properties. Partitioning of radionuclides to determine their sorption mechanisms is also being studied. The identification of fundamental magnetic properties within the microscopic chemical environment in combination with hydrodynamic and electrodynamic models provides insights into the design of a system for optimal separation. Following this, experimental studies using superconducting open-gradient magnetic separation (OGMS) will be conducted to validate its effectiveness as a pretreatment technique.'

  20. Identification of sulfur heterocycles in coal liquids and shale oils. Technical progress report, August 1, 1980-May 1, 1981

    Lee, M. L.; Castle, R. N.

    1981-01-01

    The sulfur heterocycle separation scheme which was described in the last progress report was evaluated for quantitative recovery of individual components. The results indicate that recoveries can range from 10% to approx. 30% depending on the structure of the compound. During this period, 23 unsubstituted sulfur-containing heterocyclic ring systems were synthesized in oder to confirm GC/MS identifications and for biological testing. The four possible 3-ring heterocycles and the thirteen possible 4-ring heterocycles were tested for mutagenic activity in the histidine reversion (Ames assay) system. One of the 3-ring isomers, naphtho(1,2-b)-thiophene, and six of the 4-ring isomers induced mutations in Salmonella test strains. One of these compounds, phenanthro(3,4-b)thiophene, displayed approximately the same mutagenic activity as benzo(a)pyrene. A two-step adsorption chromatographic procedure was developed in order to fractionate synthetic fuels into various chemical-type classes for studying the relative concentrations and mutagenic activities of the various types. An SRC-II Heavy Distillate was fractionated into aliphatic hydrocarbons, polycyclic aromatic hydrocarbons, sulfur heterocycles, indoles and carbazoles, azaarenes, and amino polycyclic aromatic hydrocarbons. It was found that the amino-PAH fraction contained most of the mutagenic activity. A survey was made for compounds containing both nitrogen and sulfur heteroatoms in their structures. A number of these compounds were detected by GC using nitrogen- and sulfur-selective detection.

  1. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

    Cottrell, W.B.; Klein, A.

    1976-04-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication

  2. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

    Cottrell, W.B.; Klein, A.

    1978-04-11

    This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index.

  3. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

    Cottrell, W.B.; Passiakos, M.

    1982-06-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index

  4. Index to Nuclear Safety. A technical progress review by chronology, permuted title, and author. Vol 11, No. 1 through Vol. 16, No. 6

    Cottrell, W.B.; Klein, A.

    1976-04-01

    This index to Nuclear Safety covers articles in Nuclear Safety Vol. 11, No. 1 (Jan.-Feb. 1970) through Vol. 16, No. 6 (Nov.-Dec. 1975). Included in the index is a chronological list of articles (including abstract) followed by both a KWIC index and an Author Index. Nuclear Safety is a bimonthly technical progress review prepared by the Nuclear Safety Information Center and covers all safety aspects of nuclear power reactors and associated facilities. The index lists over 300 technical articles in the last six years of publication.

  5. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author, Volume 18 (1) through Volume 22 (6)

    Cottrell, W.B.; Passiakos, M.

    1982-06-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Volume 18, Number 1 (January-February 1977) through Volume 22, Number 6 (November-December 1981). The index is divided into three section: a chronological list of articles (including abstracts), a permuted-title (KWIC) index, and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center, covers all safety aspects of nuclear power reactors and associated facilities. Over 300 technical articles published in Nuclear Safety in the last 5 years are listed in this index.

  6. Index to Nuclear Safety: a technical progress review by chronology, permuted title, and author. Vol. 11(1)--Vol. 18(6)

    Cottrell, W.B.; Klein, A.

    1978-01-01

    This index to Nuclear Safety covers articles published in Nuclear Safety, Vol. 11, No. 1 (January-February 1970), through Vol. 18, No. 6 (November-December 1977). It is divided into three sections: a chronological list of articles (including abstracts) followed by a permuted-title (KWIC) index and an author index. Nuclear Safety, a bimonthly technical progress review prepared by the Nuclear Safety Information Center (NSIC), covers all safety aspects of nuclear power reactors and associated facilities. Over 450 technical articles published in Nuclear Safety in the last eight years are listed in this index

  7. Separation, fractionation, concentration and drying of food products: Technology progress report, October 1, 1984-March 3, 1987

    Rose, W. W.; Pederson, L. D.; Merlo, C. A.; Brewbaker, P. L.

    1987-11-01

    This report describes the first and second phases of a three phase project, the object of which is to develop energy efficient separation, concentration, and drying processes for food products, especially juice products, in order to reduce energy requirements and their associated costs for processing, preservation, and transportation. Presently in juice processing, much water is eliminated through evaporation. However, there are significant limits to the current evaporation technology. If, however, the juice could be separated, prior to evaporation, into liquid and solid fractions, and the liquid concentrated further, the containerization and transportation costs could be significantly reduced. Separation methods investigated in this project are: vacuum filtration, centrifugation, and crossflow microfiltration.

  8. Generalization of Bateman-Hillion progressive wave and Bessel-Gauss pulse solutions of the wave equation via a separation of variables

    Kiselev, A

    2003-01-01

    Two new families of exact solutions of the wave equation u sub x sub x + u sub y sub y + u sub z sub z - c sup - sup 2 u sub t sub t = 0 generalizing Bessel-Gauss pulses and Bateman-Hillion relatively undistorted progressive waves, respectively are presented. In each of these families new simple solutions describing localized wave propagation are found. The approach is based on a kind of separation of variables. (letter to the editor)

  9. "A case report of Pott’s disease with unusual involvement of two separate levels of spine and delayed progressive Kyphosis "

    Rahimi Movaghar V

    2001-01-01

    In Pott’s disease (tuberculous spondylitis), involvement of two separate levels of spine is rare. Attention to stability of spine prevents delayed progressive kyphosis. A 12-year-old girl presented with neck pain, tenderness and swelling Imaging showed Cl—C2 and T9-T10 and destruction. Mild spastic paraparesis was noticed. Preoperative diagnosis was metastasis. T9, T10 and T11 laminectomy and cervical operations were done in 2 sessions. Both pathologic examinations confirmed tuberculosis. Alt...

  10. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 1 April 1996--29 September 1996

    1996-01-01

    This technical progress report discusses work on the Radioisotope Generators and Ancillary Activities for the Cassini spacecraft. The Cassini spacecraft is expected to launch in October 1997, and will explore Saturn and its moons. This progress report discusses issues in: spacecraft integration and liason, engineering support, safety, qualified unicouple fabrication, ETG fabrication and testing, ground support equipment, RTG shipping and launch support, designs, reviews and mission application. Safety analysis of the RTGs during reentry and launch accidents are covered. This report covers the period of April 1 to September 29, 1996

  11. Novel ceramic-polymer composite membranes for the separation of liquid waste. Annual progress report, September 15, 1996 - September 14, 1997

    Cohen, Y.

    1997-01-01

    'The project on ceramic-supported polymer membranes focuses on the development of a novel class of membranes for the separation of organics from both organic-aqueous and organic-organic mixtures, Theses membranes are fabricated by a graft polymerization process where polymer chains are grown onto the surface of a ceramic support membrane. The surface graft polymerization process, developed at UCLA, results in the formation of a thin polymer layer covalently bonded to the membrane pore surface as a layer of terminally anchored polymeric chains. Through the selection of the polymer most appropriate for the desired separation task, the graft polymerized surface layer can be synthesized to impart specific separation properties to the membrane. It is expected that this project will lead to the demonstration of a new technology for the tailor design of a new class of selective and robust ceramic-supported polymer membranes. This new approach will allow the rapid deployment of task-specific membranes for the separation of waste constituents for subsequent recovery, treatment or disposal. Progress to date includes the preparation of successful silica-polyvinylpyrrolidone (PVP) membrane for the treatment of oil-in-water emulsions and a silica-polyvinylacetate (PVAc) pervaporation membrane for the separation of organics from water. Current work is ongoing to study the performance of the pervaporation membrane for the removal of chlorinated organics from water and to develop a pervaporation membrane for organic-organic separation. In another aspect of the study, the authors are studying the hydrophilic PVP CSP membrane for oil-in-water emulsion treatment with the goal of determining the optimal membrane polymer surface structure as a function of various operating conditions (e.g., tube-side Reynolds number and transmembrane pressure), Work is also in progress to characterize the polymer layer by AFM and internal reflection FTIR, and to model the conformation of the polymer

  12. [Utilization of magnetic effects as a means of isotopic enrichment]: Technical progress report, January 1, 1987 to August 31, 1987

    1987-01-01

    A quantitative theory was developed. Structural variations that would enhance the efficiency of the 13 C isotope separation were explored. Photolysis of substituted large ring cyclic ketones resulted in efficient separations

  13. Phase separation of the plasma membrane in human red blood cells as a potential tool for diagnosis and progression monitoring of type 1 diabetes mellitus.

    Giuseppe Maulucci

    Full Text Available Glycosylation, oxidation and other post-translational modifications of membrane and transmembrane proteins can alter lipid density, packing and interactions, and are considered an important factor that affects fluidity variation in membranes. Red blood cells (RBC membrane physical state, showing pronounced alterations in Type 1 diabetes mellitus (T1DM, could be the ideal candidate for monitoring the disease progression and the effects of therapies. On these grounds, the measurement of RBC membrane fluidity alterations can furnish a more sensitive index in T1DM diagnosis and disease progression than Glycosylated hemoglobin (HbA1c, which reflects only the information related to glycosylation processes. Here, through a functional two-photon microscopy approach we retrieved fluidity maps at submicrometric scale in RBC of T1DM patients with and without complications, detecting an altered membrane equilibrium. We found that a phase separation between fluid and rigid domains occurs, triggered by systemic effects on membranes fluidity of glycation and oxidation. The phase separation patterns are different among healthy, T1DM and T1DM with complications patients. Blood cholesterol and LDL content are positively correlated with the extent of the phase separation patterns. To quantify this extent a machine learning approach is employed to develop a Decision-Support-System (DSS able to recognize different fluidity patterns in RBC. Preliminary analysis shows significant differences(p<0.001 among healthy, T1DM and T1DM with complications patients. The development of an assay based on Phase separation of the plasma membrane of the Red Blood cells is a potential tool for diagnosis and progression monitoring of type 1 diabetes mellitus, and could allow customization and the selection of medical treatments in T1DM in clinical settings, and enable the early detection of complications.

  14. Superconducting open-gradient magnetic separation for the pretreatment of radioactive or mixed waste vitrification feeds. 1997 annual progress report

    Cicero-Herman, C.A.; Ritter, J.A.

    1997-01-01

    'Vitrification has been selected as a final waste form technology in the US for long-term storage of high-level radioactive wastes (HLW). However, a foreseeable problem during vitrification in some waste feed streams lies in the presence of elements (e.g., transition metals) in the HLW that may cause instabilities in the final glass product. The formation of spinel compounds, such as Fe 3 O 4 and FeCrO 4 , results in glass phase separation and reduces vitrifier lifetime, and durability of the final waste form. A superconducting open gradient magnetic separation (OGMS) system maybe suitable for the removal of the deleterious transition elements (e.g. Fe, Co, and Ni) and other elements (lanthanides) from vitrification feed streams due to their ferromagnetic or paramagnetic nature. The OGMS systems are designed to deflect and collect paramagnetic minerals as they interact with a magnetic field gradient. This system has the potential to reduce the volume of HLW for vitrification and ensure a stable product. In order to design efficient OGMS and High gradient magnetic separation (HGMS) processes, a fundamental understanding of the physical and chemical properties of the waste feed streams is required. Using HLW simulant and radioactive fly ash and sludge samples from the Savannah River Technology Center, Rocky Flats site, and the Hanford reservation, several techniques were used to characterize and predict the separation capability for a superconducting OGMS system.'

  15. Recent progress in developments of membrane materials and modification techniques for high performance helium separation and recovery : a review

    Soleimany, A.; Hosseini, S.S.; Gallucci, F.

    2017-01-01

    Helium is a valuable gas with unique properties and applications and still the prominent industrial source of helium is natural gas. Because of several advantages of membrane-based separation processes over conventional methods as well as the lack of a comprehensive scientific report, the present

  16. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 1. Geological environment of Japan

    NONE

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 1 of the progress report, describes first in detail the role of geological environment in high-level radioactive wastes disposal, the features of Japanese geological environment, and programs to proceed the investigation in geological environment. The following chapter summarizes scientific basis for possible existence of stable geological environment, stable for a long period needed for the HLW disposal in Japan including such natural phenomena as volcano and faults. The results of the investigation of the characteristics of bed-rocks and groundwater are presented. These are important for multiple barrier system construction of deep geological disposal. The report furthermore describes the present status of technical and methodological progress in investigating geological environment and finally on the results of natural analog study in Tono uranium deposits area. (Ohno, S.)

  17. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. An extra issue: background of the geological disposal

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, an extra issue of the progress report, was prepared for the expected readers of the report to have background information on the geological disposal. Thus it gives information about (1) generation of high-level radioactive wastes, (2) history of plans proposed for HLW disposal in Japan, and (3) procedure until the geological disposal plan is finally adopted and basic future schedules. It further discusses on such problems in HLW treatment and disposal, as for example a problem of reliable safety for a very long period. (Ohno, S.)

  18. Development of technics for separation and sorting system of different parts of field plants; Peltokasvien eri osien erottelu- ja lajittelutekniikoiden kehittaeminen

    Lindh, T.; Kallio, E.; Taipale, R.; Leinonen, A.

    1996-12-31

    The aim of the research is to construct a segregation concept for an integrated method, by which it is possible to produce fiber fraction for pulping industry and byproduct fraction for energy production of the field plants to be processed. The starting point of the concept development was, that the method consists of the plant material processing phase, in which different plant components are segregated from each other, and a sorting phase in which the plant components are divided into different fractions on the basis of the use. Following topics were studied in the first year of this two year research: properties of spring-harvested reed canary grass and the component of it from the point of view of segregation, mechanical dry-processing methods for segregation of plant components from each other and sorting methods, by which the pulp fraction and by-product fraction are separated from each other. Chopping, crushing and milling have been studied as alternatives for processing. The particle size distribution of the produced material has been estimated. Sorting tests, based on air classification, have been made. Property analyses, such as ash content, have been made for different particle classes, by which the most suitable particle size class for sorting was determined. Processing and sorting research of chopped reed canary grass will be continued in 1996. Technical/economical analyses will be made of the costs of the separator by taking the alternatives, in which the separator unit operates at the farm or at the mill, into account. The final separation concept will be made using the results obtained in the experimental researches and cost analyses

  19. The production of chemicals from food processing wastes using a novel fermenter separator. Annual progress report, January 1993--March 1994

    Dale, M.C.; Venkatesh, K.V.; Choi, H.; Salicetti-Piazza, L.; Borgos-Rubio, N.; Okos, M.R.; Wankat, P.C.

    1994-03-15

    The basic objective of this project is to convert waste streams from the food processing industry to usable fuels and chemicals using novel bioreactors. These bioreactors should allow economical utilization of waste (whey, waste sugars, waste starch, bottling wastes, candy wastes, molasses, and cellulosic wastes) by the production of ethanol, acetone/butanol, organic acids (acetic, lactic, and gluconic), yeast diacetyl flavor, and antifungal compounds. Continuous processes incorporating various processing improvements such as simultaneous product separation and immobilized cells are being developed to allow commercial scale utilization of waste stream. The production of ethanol by a continuous reactor-separator is the process closest to commercialization with a 7,500 liter pilot plant presently sited at an Iowa site to convert whey lactose to ethanol. Accomplishments during 1993 include installation and start-up of a 7,500 liter ICRS for ethanol production at an industry site in Iowa; Donation and installation of a 200 liter yeast pilot Plant to the project from Kenyon Enterprises; Modeling and testing of a low energy system for recovery of ethanol from vapor is using a solvent absorption/extractive distillation system; Simultaneous saccharification/fermentation of raw corn grits and starch in a stirred reactor/separator; Testing of the ability of `koji` process to ferment raw corn grits in a `no-cook` process.

  20. Phase separation of the plasma membrane in human red blood cells as a potential tool for diagnosis and progression monitoring of type 1 diabetes mellitus.

    Maulucci, Giuseppe; Cordelli, Ermanno; Rizzi, Alessandro; De Leva, Francesca; Papi, Massimiliano; Ciasca, Gabriele; Samengo, Daniela; Pani, Giovambattista; Pitocco, Dario; Soda, Paolo; Ghirlanda, Giovanni; Iannello, Giulio; De Spirito, Marco

    2017-01-01

    Glycosylation, oxidation and other post-translational modifications of membrane and transmembrane proteins can alter lipid density, packing and interactions, and are considered an important factor that affects fluidity variation in membranes. Red blood cells (RBC) membrane physical state, showing pronounced alterations in Type 1 diabetes mellitus (T1DM), could be the ideal candidate for monitoring the disease progression and the effects of therapies. On these grounds, the measurement of RBC membrane fluidity alterations can furnish a more sensitive index in T1DM diagnosis and disease progression than Glycosylated hemoglobin (HbA1c), which reflects only the information related to glycosylation processes. Here, through a functional two-photon microscopy approach we retrieved fluidity maps at submicrometric scale in RBC of T1DM patients with and without complications, detecting an altered membrane equilibrium. We found that a phase separation between fluid and rigid domains occurs, triggered by systemic effects on membranes fluidity of glycation and oxidation. The phase separation patterns are different among healthy, T1DM and T1DM with complications patients. Blood cholesterol and LDL content are positively correlated with the extent of the phase separation patterns. To quantify this extent a machine learning approach is employed to develop a Decision-Support-System (DSS) able to recognize different fluidity patterns in RBC. Preliminary analysis shows significant differences(pBlood cells is a potential tool for diagnosis and progression monitoring of type 1 diabetes mellitus, and could allow customization and the selection of medical treatments in T1DM in clinical settings, and enable the early detection of complications.

  1. "A case report of Pott’s disease with unusual involvement of two separate levels of spine and delayed progressive Kyphosis "

    Rahimi Movaghar V

    2001-05-01

    Full Text Available In Pott’s disease (tuberculous spondylitis, involvement of two separate levels of spine is rare. Attention to stability of spine prevents delayed progressive kyphosis. A 12-year-old girl presented with neck pain, tenderness and swelling Imaging showed Cl—C2 and T9-T10 and destruction. Mild spastic paraparesis was noticed. Preoperative diagnosis was metastasis. T9, T10 and T11 laminectomy and cervical operations were done in 2 sessions. Both pathologic examinations confirmed tuberculosis. Although antituberculous medications and casting were performed, kyhosis progressed and neurologic deficit restrated. Reportation was done for spinal cord decompression and stabilzation. Tuberculosis could involve multiple spinal levels. Laminectomy is not suggested in children. Bone fusion and serial observations are important.

  2. Investigations of nuclear structure and nuclear reactions induced by complex projectiles. Technical progress report, November 1, 1978-October 31, 1979

    Sarantites, D.G.

    1979-01-01

    Experimental research on nuclear structure and reactions both published and in progress is summarized. Included are fusion reactions, strongly damped heavy ion collisions, and nuclear structure at high angular momentum. A list of publications is included

  3. Effect of point defects on mechanical properties of metals. Technical progress report, January 1, 1978--November 30, 1978

    Meshii, M.

    1978-11-01

    Progress is reported on deformation behavior of niobium single crystals below 77 0 K, the effect of electron irradiation on the deformation behavior of niobium single crystals, and surface film softening phenomenon in Ni plated iron single crystals

  4. New York City School Survey 2008-2010: Assessing the Reliability and Validity of a Progress Report Measure. Technical Appendices

    Nathanson, Lori; Cole, Rachel; Kemple, James J.; Lent, Jessica; McCormick, Meghan; Segeritz, Micha

    2013-01-01

    The Research Alliance for New York City Schools examined Department of Education (DOE) School Survey data from 2008-2010 to better understand the richness and complexities of the information elicited by the Survey from parents, students, and teachers. This document provides the appendices to the technical report "New York City School Survey…

  5. Technical basis for the ITER-FEAT outline design. Progress in resolving open design issues from the outline design report

    2000-01-01

    In this publication the technical basis for the ITER-FEAT outline design is presented. It comprises the Plant Design Specifications, the Safety Principles and Environmental Criteria, the Site Requirements and Site Design Assumptions. The outline of the key features of the ITER-FEAT design includes main physical parameters and assessment, design overview and preliminary safety assessment, cost and schedule

  6. GPHS-RTGs in support of the Cassini mission. Semi annual technical progress report, 2 October 1995--31 March 1996

    1996-01-01

    The technical progress achieved during the period 2 October 1995 through 31 March 1996 on Contract No. DE-AC03-91SF18852, Radioisotope Generators and Ancillary Activities is described herein. This report is organized by the program task structure as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contract acquired government-owned property (CAGO) acquisition; and program calendars

  7. Inertial fusion research: Annual technical report, 1985

    Larsen, J.T.; Terry, N.C.

    1986-03-01

    This report describes the inertial confinement fusion (ICF) research activities undertaken at KMS Fusion (KMSF) during 1985. It is organized into three main technical sections; the first covers fusion experiments and theoretical physics, the second is devoted to progress in materials development and target fabrication, and the third describes laser technology research. These three individual sections have been cataloged separately

  8. Technical aspects of high converter reactors

    1992-02-01

    The meeting provided an opportunity to review and discuss national R and D programs, various technical aspects of and worldwide progress in the implementation of high conversion reactors. The meeting was attended by 66 participants from 18 countries and 2 international organizations. 33 papers were presented. A separate abstract was prepared for each of these papers. Refs, figs, tabs, slides and diagram

  9. Separations chemistry

    Anon.

    1976-01-01

    Results of studies on the photochemistry of aqueous Pu solutions and the stability of iodine in liquid and gaseous CO 2 are reported. Progress is reported in studies on: the preparation of macroporous bodies filled with oxides and sulfides to be used as adsorbents; the beneficiation of photographic wastes; the anion exchange adsorption of transition elements from thiosulfate solutions; advanced filtration applications of energy significance; high-resolution separations; and, the examination of the separation agents, octylphenylphosphoric acid (OPPA) and trihexyl phosphate (THP)

  10. Silicon ribbon growth by a capillary action shaping technique. Annual report (Quarterly technical progress report No. 9)

    Schwuttke, G.H.; Ciszek, T.F.; Kran, A.

    1977-10-01

    Progress on the technological and economical assessment of ribbon growth of silicon by a capillary action shaping technique is reported. Progress in scale-up of the process from 50 mm to 100 mm ribbon widths is presented, the use of vitreous carbon as a crucible material is analyzed, and preliminary tests of CVD Si/sub 3/N/sub 4/ as a potential die material are reported. Diffusion length measurements by SEM, equipment and procedure for defect display under MOS structure in silicon ribbon for lifetime interpretation, and an assessment of ribbon technology are discussed. (WHK)

  11. Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark - Annual Progress Report 2009

    Korsholm, Søren Bang; Michelsen, Poul; Juul Rasmussen, Jens

    The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its...... superconductors. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2009....

  12. Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark - Annual Progress Report 2008

    Korsholm, Søren Bang; Michelsen, Poul; Juul Rasmussen, Jens

    The programme of the Research Unit of the Fusion Association Euratom - Risø National Laboratory for Sustainable Energy, Technical University of Denmark, covers work in fusion plasma physics and in fusion technology. The fusion plasma physics research focuses on turbulence and transport, and its...... been initiated in 2008. Minor activities are system analysis, initiative to involve Danish industry in ITER contracts and public information. A summary is presented of the results obtained in the Research Unit during 2008....

  13. Technical progress, the concept of individualized cancer treatment and the innovation of computer-assisted radiotherapy planning

    Merkle, K.; Tanneberger, S.; Matschke, S.

    1985-01-01

    After a first step of cancerogenesis, the further development of the tumor is an individual process. At the end of this process the tumor is formed as an individual in the individual. The individuality of cancer exists on the level of organs, tissues and cells and includes an individual tumor-host relationship. Today, optimized cancer treatment requires a most precise biological characterization possible of the tumor and of the tumor-host relationship, which will provide objective information about the individual character of every tumor. Routine analysis and strict therapeutic consideration of the clinical and biological individuality of human cancer can offer real chances for the improvement of cancer treatment. A routine acquisition of individual tumor characteristics will be possible only if methods and equipment are available for the registration of suitable parameters. In this context technical innovations have an essential influence on the realization of the concept of individualized cancer treatment. With the method of flow cytophotometry and other techniques examples are given in how far the ideas of individual cancer management can be realized by introduction of new technical solutions into medical research and clinical practice. Unfortunately there is still a lack of methodology in individualizing cancer treatment. The individualization of radiotherapy is connected to an extremely high degree of technical innovations. Particularly this refers to the topometrical description of the target volume in relation to the adjacent anatomical structures and the body contour as well as the fitting of isodoses to the shape and size of the target volume. As an example of innovation of a technical solution for individual radiotherapy planning the computer-assisted radiotherapy planning system DOPSY is described. (author)

  14. Studies in chemical dynamics and radiation chemistry. Technical progress report, 1 July 1974--30 June 1975

    Kuppermann, A.

    1975-01-01

    Research progress in the following areas is reported: low energy electron scattering; photoelectron spectrometry; elementary reactions by photolysis at variable wavelengths; collisions in crossed molecular beams; and, diffusion kinetics in the radiation chemistry of water. Publications related to the work are included. (JGB)

  15. Sodium boiling detection in LMFBRs (Phase I). 5th quarterly technical progress report, July 1, 1975--October 31, 1975

    Albrecht, R.W.; McCormick, N.J.

    1975-01-01

    Progress summarized includes the design of a gamma heated subassembly for sodium boiling experiments and an experiment showing that neutronic noise and acoustic noise caused by sodium boiling are highly correlated in a wide frequency band about the bubble repetition frequency

  16. Effects of Water Radiolysis in Water Cooled Reactors - Nuclear Energy Research Initiative (NERI) Program. Technical Progress Report

    Pimblott, S.M.

    2000-01-01

    OAK B188 Quarterly Progress Report on NERI Proposal No.99-0010 for the Development of an Experiment and Calculation Based Model to Describe the Effects of Radiation on Non-standard Aqueous Systems Like Those Encountered in the Advanced Light Water Reactor

  17. Effects of humic substances on the migration of radionuclides: complexation and transport of actinides. First technical progress report (work period 01.97 - 12.97)

    Buckau, G.

    1998-08-01

    The present report describes progress within the first year of the EC-project 'Effects of Humic Substances on the Migration of Radionuclides: Complexation and Transport of Actinides'. The project is conducted within the EC-Cluster 'Radionuclide Transport/Retardation Processes'. Contrary to formal requirements of the Commission, this report with a great deal of detail is established already after one year of project work. It is scheduled to be followed by a second technical progress report covering the second year of the project. In agreement with the contractual obligations a final report of similar technical detail will also be generated. The report contains an executive summary written by the coordinator (FZK/INE) with strong support from the other three task leaders (BGS, CEA-SGC and RMC-E). More detailed results are given by individual contributions of the project partners in 13 annexes. In the executive summary report the origin of results presented is given, also serving as guidance for finding more detailed results in the annexes. Not all results are discussed or referred to in the executive summary report and thus readers with a deeper interest also need to consult the annexes. (orig.)

  18. A systematic assessment of the state of hazardous waste clean-up technologies. Quarterly technical progress report, April 1--June 30, 1993

    Berg, M.T.; Reed, B.E.; Gabr, M.

    1993-07-01

    West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushing (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming.

  19. Diagnostic development and support of MHD test facilities: Technical progress report for the period January, February, March 1985

    Shepard, W.S.; Cook, R.L.

    1985-04-01

    Mississippi State University is developing diagnostic instruments for MHD power train data acquisition and for support of MHD component development test facilities. Microprocessor-controlled optical instruments, initially developed for HRSR support, are being refined, and new systems to measure temperatures and gas-seed-slag stream characteristics are being developed. To further data acquisition and analysis capabilities, the diagnostic systems are being interfaced with MHD Energy Center computers. Additionally, technical support of the diagnostic needs of the national MHD research effort is being provided

  20. Research and development on optically pumped polarized ion sources. Technical progress report, February 1, 1985-January 31, 1986

    Anderson, L.W.

    1985-07-01

    During the past year we have studied the relaxation times in an optically pumped 23 Na vapor target, studied the effects of radiation trapping on the polarization in a Na vapor target, and have studied the effects of spin exchange collisions on a beam of fast H 0 atoms as they pass through a polarized alkali target. This research is directed toward improvements in the optically pumped Na or other alkali vapor targets used for the production of polarized H - ions. In this progress report we review the properties of the optically pumped polarized H - ion source as well as discussing the progress of our research on optically pumped Na or other alkali vapor targets. 81 refs., 9 figs

  1. Technical progress report of biological research on the Volcanic Island Surtsey and its environs for the period 1965--1978

    Fridriksson, S.

    1978-01-01

    Progress is reported on the following research projects: changes in shoreline and surface of the island due to volcanic activity; colonization of microorganisms, algae, lichens, and vascular plants; introduction of insects and other arthropods by wind, water, and man; transport of invertebrates to the island by flotsam of the sea; species and nesting habits of birds on the island; behavior of seals on beaches of the island; and future trends of Surtsey ecosystems. (HLW)

  2. Research proposal and annual report No. 16. Part B. Technical progress, September 1, 1975--August 31, 1976

    1976-06-01

    Progress is reported on the following research projects: RNA synthesis in yeast; regulation of nitrogen metabolism; biological toxicity of intracellular radioisotope decay; the mechanism of energy conversion in chloroplasts; promoting vibrations in spin-orbital coupling in vibrationally deficient molecules; electronic excitation and hydrogen bonding; macromolecular biophysics; the synthesis and maturation of RNA; electronic response properties of biomolecular systems; chromosome structure and function and chromosome damage; DNA replication and chromosome structure; and influence of phospholipids on the dynamic properties of rhodopsin. (HLW)

  3. Research proposal and annual report No. 16. Part B. Technical progress, September 1, 1975--August 31, 1976

    1976-01-01

    Progress is reported on the following research projects: RNA synthesis in yeast; regulation of nitrogen metabolism; biological toxicity of intracellular radioisotope decay; the mechanism of energy conversion in chloroplasts; promoting vibrations in spin-orbital coupling in vibrationally deficient molecules; electronic excitation and hydrogen bonding; macromolecular biophysics; the synthesis and maturation of RNA; electronic response properties of biomolecular systems; chromosome structure and function and chromosome damage; DNA replication and chromosome structure; and influence of phospholipids on the dynamic properties of rhodopsin

  4. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 3. Safety assessment for geological disposal systems

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 3 of the progress report, concerns safety assessment for geological disposal systems definitely introduced in part 1 and 2 of this series and consists of 9 chapters. Chapter I concerns the methodology for safety assessment while Chapter II deals with diversity and uncertainty about the scenario, the adequate model and the required data of the systems above. Chapter III summarizes the components of the geological disposal system. Chapter IV refers to the relationship between radioactive wastes and human life through groundwater, i.e. nuclide migration. In Chapter V is made a reference case which characterizes the geological environmental data using artificial barrier specifications. (Ohno. S.)

  5. High temperature turbine technology program. Phase II. Technology test and support studies. Annual technical progress report, January 1, 1979-December 31, 1979

    1980-01-01

    Work performed on the High Temperature Turbine Technology Program, Phase II - Technology Test and Support Studies during the period from January 1, 1979 through December 31, 1979 is summarized. Objectives of the program elements as well as technical progress and problems encountered during this Phase II annual reporting period are presented. Progress on design, fabrication and checkout of test facilities and test rigs is described. LP turbine cascade tests were concluded. 350 hours of testing were conducted on the LP rig engine first with clean distillate fuel and then with fly ash particulates injected into the hot gas stream. Design and fabrication of the turbine spool technology rig components are described. TSTR 60/sup 0/ sector combustor rig fabrication and testing are reviewed. Progress in the design and fabrication of TSTR cascade rig components for operation on both distillate fuel and low Btu gas is described. The new coal-derived gaseous fuel synthesizing facility is reviewed. Results and future plans for the supporting metallurgical programs are discussed.

  6. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 2. Engineering technology for geological disposal

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the deep geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, part 2 of the progress report, concerns engineering aspect with reference to Japanese geological disposal plan, according to which the vitrified HLW will be disposed of into a deep, stable rock mass with thick containers and surrounding buffer materials at the depth of several hundred meters. It discusses on multi-barrier systems consisting of a series of engineered and natural barriers that will isolate radioactive nuclides effectively and retard their migrations to the biosphere environment. Performance of repository components, including specifications of containers for vitrified HLW and their overpacks under design as well as buffer material such as Japanese bentonite to be placed in between are described referring also to such possible problems as corrosion arising from the supposed system. It also presents plans and designs for underground disposal facilities, and the presumed management of the underground facilities. (Ohno, S.)

  7. Design and synthesis of the next generation of crown ethers for waste separations: An inter-laboratory comprehensive proposal. 1998 annual progress report

    Alexandratos, S.D.; Chiarizia, R.; Dietz, M.L.; Hay, B.P.; Moyer, B.A.; Sachleben, R.A.

    1998-01-01

    'The purpose of this task is to undertake the design, synthesis, and characterization of the next generation of crown ethers for metal-ion separations applicable to USDOE''s environmental needs. Target problems include: Li + ions leaching from burial sites at the Oak Ridge Y-12 Plant; fission products 90 Sr and 137 Cs contaminating high-level tank wastes at Hanford, INEEL, and Savannah River; and radium in wastes at the Niagara Falls Storage Site. Unfortunately, the technologies needed to address these problems either do not exist or exhibit substantial deficiencies. Separation techniques such as solvent extraction and ion exchange promise to play a strong role, especially as enhanced with highly selective crown ethers and calixarenes. This project is midway through year 2 of a 3-year effort. Below is given a summary of progress in the approximate period September, 1997, to May, 1998, for each of the four co-investigators at Pacific Northwest National Laboratory (PNNL), Argonne National Laboratory (ANL), Oak Ridge National Laboratory (ORNL), and the University of Tennessee (UTK). The overall approach entails utilization of theory and molecular modeling (PNNL), organic synthesis of novel crown compounds (ORNL), solvent extraction studies (ORNL and ANL), and studies of polymer-immobilized crown ethers (UTK).'

  8. Adsorption/membrane filtration as a contaminant concentration and separation process for mixed wastes and tank wastes. 1998 annual progress report

    Benjamin, M.M.; Korshin, G.

    1998-01-01

    'This report describes progress through May, 1998, which is a little past mid-way through the second year of a three-year project. The goal of the research is to develop a treatment system for the separation of contaminants in low-organic Hanford tank wastes into various sub-groups that are relatively easy to treat further to yield products that are amenable to final disposal. The main target contaminants are Sr and Cs, although heavy metals and actinide-group elements are also targets. Effort during the first half-year of the project was devoted primarily to development of experimental and analytical techniques that could be used to test and quantify the treatability of Sr and Cs in the extremely complex matrix of the tank wastes. The treatment technologies to be tested for isolation of Sr from other waste constituents included adsorption of Sr onto various mineral solids and membrane separation of particulate from dissolved Sr. The proposed technology for treating Cs was electrochemically controlled, reversible binding of the Cs to hexacyanoferrates. Results obtained during the remainder of the first year suggested that hematite (a-Fe 2 O 3 ) and iron-oxide-coated sand (IOCS) were the best adsorbents for Sr among the oxides tested, and work during the second project year followed up on that result.'

  9. Gas-Cooled Thermal Reactor Program. Annual technical progress report for the period ending September 30, 1981

    1982-03-01

    This report provides descriptions and results of the technical effort during FY81 on the Gas-Cooled Thermal Reactor Program. The FY81 work was organized according to the Work Breakdown Structure (WBS) for the National HTGR Program, and fell within five of the WBS tasks. The work on Market Definition and Development (WBS 03) was associated with estimating product costs for HTGR systems and their alternatives, projecting markets and market penetrations for these systems, and providing costs and market input to application analyses and component design. The Plant Technology (WBS 13) effort was mainly in the development of the systems dynamic computer code, STAR, for the transient analysis of HTGR's in reformer applications. The analysis of pebble bed reactors (PBR) was performed under Technology Transfer (WBS 15). The effort on components and systems within the nuclear heat source for reforming plants was performed under High Temperature Nuclear Heat Source (WBS 42)

  10. Realization of radiation-chemical processes in national economy-important stage of scientific and technical progress

    Breger, A.Kh.

    1975-01-01

    Realization of energy resourses of the atomic power engineering will greatly contribute to the scientific and technological progress. The dominat role play the radiochemical methods of properties modification applied for the well-known materials and for the production of materials with modern operating characteristics necessary for their application in different branches of industry and agriculture. Radiation modeling of products from polyolefine, wood-plastic and concrete-polymer materials are considered as well as the processes in ''thin'' units of agitating systems. The future developments and present state of the art of radiation sources are presented

  11. Committee on Atomic, Molecular, and Optical Sciences (CAMOS). Technical progress report ampersand continuation proposal, February 1, 1993--January 31, 1994

    Taylor, R.D.

    1997-01-01

    The Committee on Atomic, Molecular and Optical Sciences (CAMOS) of the National Research Council (NRC) is charged with monitoring the health of the field of atomic, molecular, and optical (AMO) science in the United States. Accordingly, the Committee identifies and examines both broad and specific issues affecting the field. Regular meetings, teleconferences, briefings from agencies and the scientific community, the formation of study panels to prepare reports, and special symposia are among the mechanisms used by the CAMOS to meet its charge. This progress report presents a review of CAMOS activities from February 1, 1993 to January 31, 1994. The details of prior activities are discussed in earlier progress reports. This report also includes the status of activities associated with the CAMOS study on the field that is being conducted by the Panel on the Future of Atomic, Molecular, and Optical Sciences (FAMOS). During the above period, CAMOS has continued to track and participate in, when requested, discussions on the health of the field. Much of the perspective of CAMOS has been presented in the recently-published report Research Briefing on Selected Opportunities in Atomic, Molecular, and Optical Sciences. That report has served as the basis for briefings to representatives of the federal government as well as the community-at-large. In keeping with its charge to monitor the health of the field, CAMOS launched a study designed to highlight future directions of the field

  12. The development of coal-based technologies for Department of Defense facilities. Technical progress report, September 1995 - March 1996

    Miller, B.G.; Pisupati, S.V.; Scaroni, A.W. [and others

    1996-10-01

    The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Slurry Fuel Technology, with the aim of decreasing DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Activities this reporting period are summarized by phase. During this reporting period, the Phase I final report was completed. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included completing a study to identify appropriate SO{sub 2} and NO{sub x} control technologies for coal-fired industrial boilers. In addition, work continued on the design of a ceramic filtering device for installation on the demonstration boiler. The ceramic filtering device will be used to demonstrate a smaller and more efficient filtering device for retrofit applications. Work related to coal preparation and utilization, and the economic analysis was primarily focused on preparing the final report. Work in Phase III focused on coal preparation studies and economic analyses of coal use. Coal preparation studies were focused on continuing activities on particle size control, physical separations, surface-based separation processes, and dry processing. The economic study focused on community sensitivity to coal usage, regional economic impacts of new coal utilization technologies, and constructing a national energy portfolio.

  13. Establishment of the Center for Advanced Separation Technologies

    Christopher E. Hull

    2006-09-30

    This Final Technical Report covers the eight sub-projects awarded in the first year and the five projects awarded in the second year of Cooperative Agreement DE-FC26-01NT41091: Establishment of the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices.

  14. Theoretical research in intermediate-energy nuclear physics. [Technical progress report, April 1, 1993--March 31, 1994

    Seki, R.

    1994-01-01

    This paper discusses progress that has been made on the following seven problems: (1) (e, e'p) at high momentum transfer; (2) post,acceleration effects in two-nucleon interferometry of heavy-ion collisions; (3) pion-nucleus interactions above 0.5 GeV; (4) chiral symmetry breaking in nuclei and picnic atom anomaly; (5) atomic screening on nuclear astronomical reactions; (6) QCD related work (coherent pion production from skyrmion-antiskyrmion annihilation, QCD in 1 + 1 dimensions, and correlation functions in the QCD vacuum), and (7) kaonic hydrogen atom experiment. The problems deal with various topics mostly in intermediate-energy nuclear physics. We place priority on (1) and (2), and describe them somewhat in detail below. Other problems are our on-going projects, but we are placing lower priority on them in the second and third year

  15. Measurements of scattering processes in negative ion: Atom collisions. Technical progress report, 1 September 1991--31 December 1994

    Kvale, T.J.

    1994-01-01

    This report describes the progress made on the research objectives during the past three years of the grant. This research project is designed to study various scattering processes which occur in H - collisions with atomic (specifically, noble gas and atomic hydrogen) targets in the intermediate energy region. These processes include: elastic scattering, single- and double-electron detachment, and target excitation/ionization. For the elastic and target inelastic processes where H - is scattered intact, the experimental technique of Ion Energy-Loss Spectroscopy (IELS) will be employed to identify the final target state(s). In most of the above processes, cross sections are unknown both experimentally and theoretically. The measurements will provide total cross sections (TCS) initially, and once the angular positioning apparatus is installed, will provide angular differential cross sections (ADCS)

  16. AFCT/TFCT/ISFS Program. Technical progress report for the period October 1, 1977--December 31, 1977

    Hill, O.F. (comp.)

    1978-02-01

    This is the eighth in a series of quarterly progress reports on studies performed for the Alternate Fuel Cycle Technologies/Thorium Fuel Cycle Technologies/International Spent Fuel Receipt and Storage (AFCT/TFCT/ISFS) Program, formerly the LWR Fuel Recycle Program. This program is designed to provide information needed by industry to close the back end of the power reactor fuel cycle. During the past quarter, studies were conducted in the following tasks: Survey of Current Technology of Fuel Handling Techniques; Investigation of Air Cleaning Processes for Removing Tributyl Phosphate (TBP) from Off-Gas Streams; Study of Iodine Chemistry in Process Solutions; Electropolishing to Decontaminate Metallic Waste from Alternate and Thorium Converter Fuel Cycles; and U.S. Scale Transport, Dispersion and Removal Mode Comparison Safety Criticality Experiments. (11 figs., 7 tables)

  17. Combined macroscopic and microscopic approach to the fracture of metals. Technical progress report, July 1975--June 1976

    Gurland, J.; Rice, J.R.; Asaro, R.J.; Needleman, A.

    1976-07-01

    Major studies have been started on (1) The conditions governing the localization of plastic flow at the onset of rupture. Specific calculations of critical conditions for a number of material models have been made possible through a theoretical framework by which localization is formulated as a constitutive instability, in the form of a bifurcation into a localized mode from a state of previously homogeneous deformation, and (2) The strength of interfaces with and without the presence of dissolved segregants. Criteria for brittle vs. ductile response of an interface were developed on the basis of dislocation mechanisms and thermodynamic relations, and applied to hydrogen embrittlement. Further progress has been achieved in the analysis of stress and deformation at a crack tip by the application of the large-strain elastic-plastic finite element program developed over the last two years. Work has continued on particle and sub-boundary strengthening in steels and an experimental study of fracture initiation at particles was begun

  18. AFCT/TFCT/ISFS Program. Technical progress report for the period April 1, 1978--June 30, 1978

    Hill, O.F. (comp.)

    1978-08-01

    This is the tenth in a series of quarterly progress reports on studies performed for the Alternate Fuel Cycle Technologies/Thorium Fuel Cycle Technologies/International Spent Fuel Receipt and Storage (AFCT/TFCT/ISFS) Program. This program provides information needed by industry to close the back end of the power reactor fuel cycle. During the past quarter, studies were conducted in the following tasks: thorium resource price analyses; spent fuel receipt and storage; investigation of air cleaning processes for removing TBP from off-gas streams; study of iodine chemistry in process solutions, high-level waste treatment; electropolishing to decontaminate metallic waste from alternate and thorium converter fuel cycles; U.S. scale transport, dispersion and removal model comparison; safety criticality experiments; and criticality research in support of thorium fuel cycle.

  19. Bench-scale testing of on-line control of column flotation using a novel analyzer. Third quarterly technical progress report, April 1, 1993--June 30, 1993

    1993-08-24

    This document contains the third quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTETM Column Flotation Technology and PTI`s On-Line Quality Monitor and Control System. The twelve-month project involves installation and testing of a 200--300 lb/hr. bench-scale flotation circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) for two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). Figure 1 contains the project plan, as well as the approach to completing the major tasks within the twelve-month project schedule. The project is broken down into three phases, which include: Phase I -- Preparation: The preparation phase was performed principally at PTI`s Calumet offices from October through December, 1992. It involved building of the equipment and circuitry, as well as some preliminary design and equipment testing; Phase II -- ET Circuit Installation and Testing: This installation and testing phase of the project was performed at PETC`s CPPRF from January through June, 1993, and was the major focus of the project. It involved testing of the continuous 200--300 lb/hr. circuit; and Phase III -- Project Finalization: The project finalization phase is occurring from July through September, 1993, at PTI`s Calumet offices and involves finalizing analytical work and data evaluation, as well as final project reporting. This Third Quarterly Technical Progress Report principally summarizes the results from the benchscale testing with the second coal (Pittsburgh No. 8 Seam Coal), which occurred in April through June, 1993. It also contains preliminary economic evaluations that will go into the Final Report, as well as the plan for the final reporting task.

  20. Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

    1996-01-01

    The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations

  1. Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

    NONE

    1996-01-01

    The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations.

  2. Progress of the radioactive waste management at the Dalat Nuclear Research Institute and the role of an IAEA technical co-operation project in this process

    Nang, N.T.; Ngoc, O.V.; Nhu Thuy, T.T.; Nghi, D.V.; Thu, N.T.

    2002-01-01

    At present, the main radioactive waste generator in Vietnam is the Dalat Nuclear Research Institute (DNRI). For safe management of radioactive waste generated from this nuclear center, in 1982 Soviet specialists newly constructed one combined technology system for low level radioactive waste management. The existing system consists of two main parts, a Liquid Radioactive Waste Treatment Station and a Storage/Disposal Facility. The liquid treatment station can in principle meet the needs for this nuclear center but disposal technology and storage/disposal facilities are not good enough both with respect to safety and economy, especially the storage/disposal facility placed in Dalat, the tourist city. In order to help DNRI and Vietnam to solve the radioactive waste management problem, the IAEA Technical Co-operation (TC) project VIE/9/007 was implemented in Vietnam. The facilities and IAEA experts provided under this project gradually help to develop radioactive waste management at DNRI, Vietnam. This paper outlines progress under way in the management of the radioactive waste at the Nuclear Research Institute (NRI), Dalat, Vietnam, and the role of the IAEA Technical Co-operation (TC) project in this process. (author)

  3. Separation of alkali, alkaline earth and rare earth cations by liquid membranes containing macrocyclic carriers. Third progress report, September 1, 1980-April 1, 1981

    Christensen, J.J.

    1981-01-01

    The overall objective of this project is to study the use of liquid membrane systems employing macrocyclic ligand carriers in making separations among metal cations. During the third year of the project, work continued in the development of a mathematical model to describe cation transport. The model was originally developed to describe the relationship between cation transport rate (J/sub M/) and the cation-macrocycle stability constant (K). The model was tested by determining the rates of transport of alkali and alkaline earth cations through chloroform membranes containing carrier ligands where the stability constants for their reaction with cations in methanol were known. From the results, it is clear that the model correctly describes the dependence of J/sub M/ on log K. The model also correctly describes the effect of cation concentration and carrier concentration on cation transport rates, as detailed in the previous progress report. During the third year of the project, the transport model was expanded so as to apply to competitive transport of cations from mixtures of two cations in the source aqueous phase. Data were collected under these conditions and the ability of the model to predict the flux of each cation was tested. Representative data of this type are presented along with corresponding data which were obtained when each cation was transported by the same carrier from a source phase containing only that cation. Comparison of transport rates determined under the two experimental conditions indicates that the relationship between the two sets of data is complex. To date, a few of these data involving transport from binary cation mixtures have been tested against the transport model. It was found that the model correctly predicts the cation fluxes from cation mixtures. These preliminary results indicate that the transport model can successfully predict separation factors when cation mixtures are used

  4. Nemaha Uplift seismotectonic study: regional tectonics and seismicity of eastern Kansas. Technical progress report, October 1, 1978-September 30, 1979

    Wilson, F.W.

    1979-11-01

    Progress and results of all work on this project to the end of its second year, or September 30, 1978, were reported in NUREG/CR-0666, published March 1979. Project third-year activites and results include the following: continued operation of a regional microearthquake monitoring network which detected and located 26 regional events between October 1, 1978, and August 2, 1979; designing and building a triggering system to allow digitized recording of microearthquakes by a modified exploration seismography; continued surface and subsurface studies of selected areas along the Nemaha Uplift-Keweenanan Mafic belt trend; continued study of Precambrian rock types from recently drilled wells; beginning compilation of a fault catalog; terrain analysis and lineament studies which indicate that the alignment of stream drainages and divides are strongly controlled by basement and subsurface structure; continued reduction of gravity data for northeastern Kansas (a Bouguer gravity map probably will be available late Fall 1979); modification of the exploration seismograph system to a more efficient 12-channel Mini-Sosie system and completion of several line-miles of reflection profiling; and beginning integration of data from Oklahoma, Nebraska, and Iowa co-investigators. All major goals for FY 1979 were accomplished. 2 figures

  5. Establishment of an Institute for Fusion Studies. Technical progress report, 1 November 1993--31 October 1994

    Hazeltine, R.D.

    1994-07-01

    The Institute for Fusion Studies is a national center for theoretical fusion plasma physics research. Its purposes are: (1) to conduct research on theoretical questions concerning the achievement of controlled fusion energy by means of magnetic confinement--including both fundamental problems of long-range significance, as well as shorter-term issues; (2) to serve as a national and international center for information exchange by hosting exchange visits, conferences, and workshops; (3) and to train students and postdoctoral research personnel for the fusion energy program and plasma physics research areas. The theoretical research results obtained by the Institute contribute to the progress of nuclear fusion research, whose goal is the development of fusion power as a basic energy source. Close collaborative relationships have been developed with other university and national laboratory fusion groups, both in the US and abroad. In addition to its primary focus on mainstream fusion physics, the Institute is also involved with research in fusion-sidestream fields, such as advanced computing techniques, nonlinear dynamics, space plasmas and astrophysics, statistical mechanics, fluid dynamics, and accelerator physics. Important research discoveries are briefly described

  6. Exotic atoms: Hadronic and muonic atoms 1969--1997. Technical progress report, February 1, 1996--August 31, 1997

    Kunselman, R.

    1997-01-01

    Since this is a terminal progress-report it is a synopsis over the total time of the grant. The author has utilized exotic hadronic and muonic atoms as tools to access information concerning questions to do with particle, nuclear, and atomic physics. The information has answered fundamental questions about lepton conservations, quark models, tests of the CPT theorem, QED energies, and nuclear structure. The present experiments involve reactions with a variety of hydrogen isotopic mixtures to form solid targets to produce muonic hydrogen isotope atoms. The method relies on muon capture by a proton and transfer of the muon from the proton to a deuteron or a triton. The resulting muonic deuterium or muonic tritium will not immediately thermalize because of the very low elastic cross sections of the Ramsauer-Townsend effect, and are emitted from the surface of the layer and escape into a vacuum region. A second solid hydrogen isotopic target is produced downstream on which the muonic hydrogen atom can react and the time of flight measured

  7. Indiana University High Energy Physics Group: Task A: Technical progress report, December 1, 1986 to November 30, 1987

    Alyea, E.D.; Brabson, B.B.; Crittenden, R.R.; Dzierba, A.R.; Martin, H.J.; Ogren, H.O.; Zieminski, A.

    1987-05-01

    Data collection on the production of the KKπ state in π - , K - , and p-bar induced reactions is reported, with partial wave analysis in progress. Work on the design of a target calorimeter and data taking for a muon scattering experiment at CERN is completed. Analysis of a fixed-target jet experiment is reported. A dimuon detector has been prepared for an experiment at Fermilab to study hadronic processes yielding high mass dimuons and associated particles. Participation in the coordination and writing of software for the DO collider detector at Fermilab is reported. Some results from the High Resolution Spectrometer (HRS) are reported, including direct observation of several decay modes of the charmed mesons, directly observed meson resonances, baryon resonances, and some discoveries concerning the tau lepton. Activity is reported in the building of hardware for the muon upgrade for the Mark2 detector at the SLC and the building of the beam position monitors for the SLC, and microprocessors for Mark2 data analysis. Involvement in the SLC polarization collaboration is also reported

  8. Intermediate-energy nuclear physics. Task C. Technical progress report, October 1, 1982-October 1, 1983. Part I

    1983-01-01

    Progress is reported on the following experimental studies: (1) excitation of giant resonances in 118 Sn in inelastic pion scattering at 130 MeV; (2) giant dipole excitations of 40 Ca by inelastic pion scattering; (3) charge symmetry test using the π + and π - elastic scattering from deuterium at 143 and 256 MeV; (4) binding energy effects on the isospin amplitudes in p-shell nuclei; (5) the energy dependence of the 14 C (π + ,π 0 ) 14 N reaction to the IAS; (6) the ( 3 He,t) reaction at 2 GeV; (7) analyzing power in the (polarized p,n) IAS transitions; (8) the excitation of the 1/2 + (2.36) MeV state in the 24Mg (polarized p,d) reaction from 27 to 150 MeV; (9) the energy dependence of the (polarized p,d) reaction for 54 Fe and 140 Ce; and (10) the energy dependence of the 7 Li(p,d) 6 Li reaction. Publications are listed

  9. Molluscs and echinoderms aquaculture: biological aspects, current status, technical progress and future perspectives for the most promising species in Italy

    Antonio Pais

    2012-10-01

    Full Text Available Shellfish aquaculture is a widespread activity in the Italian peninsula. However, only two bivalve species are mainly cultured along the coastline of that country: the Mediterranean mussel Mytilus galloprovincialis and the Manila clam Venerupis philippinarum (Ruditapes philippinarum. By contrast, just a few other mollusc species of commercial interest are scarcely reared at a small-scale level. After analysing the current status of Italian shellfish production, this paper reports and discusses the potential for culturing several different invertebrate species [i.e., the European flat oyster Ostrea edulis, the grooved carpet shell Venerupis decussata (Ruditapes decussatus, the razor clams Ensis minor and Solen marginatus, the cephalopod Octopus vulgaris, and the purple sea urchin Paracentrotus lividus] in this country. In addition, a detailed overview of the progress made in aquacultural techniques for these species in the Mediterranean basin is presented, highlighting the most relevant bottlenecks and the way forward to shift from the experimental to the aquaculture phase. Finally, an outlook of the main economic and environmental benefits arising from these shellfish culture practices is also given.

  10. 1991 Technical progress report of the University of South Carolina's High Energy Physics Group, February 1990--July 1991

    1991-01-01

    The high energy physics group at the University of South Carolina includes five teaching faculty members, one research faculty member, and five graduate students. Profs. Childers, Darden, and Wilson devote most of their research effort to Fermilab experiment E789, which is designed to observe charmless two-body decays of b-flavored mesons and baryons. Prof. Wilson works on Fermilab experiment E687 which studies charm physics in the wide-band photon beam. Profs. Rosenfeld and Wang participate in the AMY collaboration, which studies electron-positron interactions using the TRISTAN collider at KEK. Prof. Rosenfeld and one student collaborate with personnel from KEK and INS, Tokyo, on an experiment to detect a 17 keV neutrino in the β-decay spectrum of 63 Ni. Members of the group also participate in Fermilab Proposal P803 which will search for the oscillation of muon neutrino to tau neutrino with sensitivity better than a factor of 40 than previously achieved and in Superconducting Super Collider activities which include the development of an imaging preradiator. A brief discussion is given on progress made for each program

  11. ITER technology R and D progress report. Report by the Director. ITER technical advisory committee meeting, 25-27 June 2000, St. Petersburg

    2001-01-01

    The overall philosophy for the ITER design has been to use established approaches through detailed analysis and to validate their application to ITER through technology R and D, including fabrication of full scale or scalable models of key components. All this R and D work has been done for ITER under collaboration among the Home Teams, with a total resource of about 660 KIUA. R and D issues for ITER-FEAT are almost the same as for the 1998 ITER design. Major developments and fabrication have been completed and tests have significantly progressed. The technical output from the R and D validates the technologies and confirms the manufacturing techniques and quality assurance incorporated in the ITER design, and supports the manufacturing cost estimates for important key cost drivers. The testing of models is continuing to demonstrate their performance margin and/or to optimize their operational use. Their realisation offers insights useful for a possible future collaborative construction activity. Valuable and relevant experience has already been gained in the management of industrial scale, cross-party ventures. The successful progress of these projects increases confidence in the possibility of jointly constructing ITER in an international project framework. The R and D present status is summarized in the following: details are given in Chapters 2 and 3. Significant efforts and resources have been devoted to the Seven Large R and D Projects which cover all the major key components of the basic machine of ITER and their maintenance tools

  12. CCNY collaboration with BNL in R and D for ISABELLE detectors. Technical progress report, November 1, 1980-June 10, 1981

    Lindenbaum, S.J.

    1981-01-01

    The difference in ionization loss of particles as a function of their velocity is widely used as a technique to identify the particles. The ionization loss in gas samples an order of magnitude smaller than previously investigated was studied. In order to do this, new techniques were developed which use a longitudinal drift ionization detector and fast analog to digital conversion techniques which allow one to effectively slice a piece of track into very small samples by electronic means using a small prototype chamber. It was demonstrated that this technique can substantially improve the mass resolution capability of gas particle detectors, and was shown that only a rather coarse analog to digital converter (ADC) resolution is required to capture all the information needed with the truncated mean sampling method employed to determine the relative energy loss. These new developments can substantially increase the sensitivity of particle separation by ionization measurements via gas particle detectors. A larger ten-layer prototype is now being tested which will optimize the design for a large type of test chamber which could then be utilized to design actual experimental measuring equipment

  13. Radioactive waste management-colloidal adsorption of cations and anions. Technical progress report (semiannual), September 30, 1985-March 31, 1986

    Balam, B.S.

    1986-04-01

    The surface adsorption characteristics of ion-exchange resins and clay minerals as influenced by the type of colloidal material, activity of ions and the concentration of associated electrolytes are being investigated. Electrodes and dialysis techniques are being used to determine the binding and release characteristics of cations and anions of significance in the radioactive waste management. The results obtained and techniques employed for clay fractionation, colloidal material separation, cation exchange capacity measurement and preparation of monocationic saturated colloidal materials have already been reported. The research work was continued to determine the distribution, mobility and binding characteristics of Montmorillonite and Illite clay materials as affected by the degree of saturation of colloidal adsorption capacity and the presence of electrolytes. Donnan equilibrium systems using Ca:Rb ratios of 90:10, 75:25, 50:50 and 10:90 and electrolyte concentrations corresponding to 0 and 0.2 symmetries were established. The systems were allowed to attain equilibrium as judged by conductivity measurements of the dialyzate. The distribution of cations at equilibrium was calculated from ion selective electrode and spectrophotometric measurements

  14. Humic substances in performance assessment of nuclear waste disposal: Actinide and iodine migration in the far-field. First technical progress report

    Buckau, G.

    2003-04-01

    The present project is one in a series of research activities supported by the European Commission on the role of humic substances for the long-term safety of nuclear waste disposal. These activities started in the mid eighties within the MIRAGE project (MIgration of RAdionuclides in the GEosphere) with the most recent project being ''Effects of humic substances on the migration of radionuclides: Complexation and transport of actinides (HUMICS)'' (FI4W-CT96-0028). The HUMICS project was conducted within the fourths framework of the European Commissions research program. It started January 1997 and had a duration of three years. The results of the HUMICS project can be found in three open technical progress reports and a final report [1-4]. In analogy with the HUMICS project, the present project makes use of annual technical progress reports where individual results are published as papers in the form of annexes. By this approach, results rapidly become available to interested parties in a compact form before their publication in various scientific journals and conference proceedings. Furthermore, some of the more preliminary and/or detailed results are not likely to appear in scientific journals and proceedings. The present project is conducted within the fifths framework of the European Commissions research program. It started November 2001 and has a duration of three years. The present report covers the first project year, i.e. November 2001 to September 2002. The project is divided into eight different work packages. These are (i) ''Critical assessment of experimental methods'', (ii) ''Generation and characterization of humic substances'', (iii) ''Radionuclide humate interaction data by designed system investigations'', (iv) ''Characterization of radionuclide humate complexes'', (v) ''Natural chemical analogue studies'', (vi) ''Radionuclide transport experiments'', (vii) ''Model development'', and (viii) ''Performance assessment''. Division of work into

  15. Advanced isotope separation

    1982-01-01

    The Study Group briefly reviewed the technical status of the three Advanced Isotope Separation (AIS) processes. It also reviewed the evaluation work that has been carried out by DOE's Process Evaluation Board (PEB) and the Union Carbide Corporation-Nuclear Division (UCCND). The Study Group briefly reviewed a recent draft assessment made for DOE staff of the nonproliferation implications of the AIS technologies. The staff also very briefly summarized the status of GCEP and Advanced Centrifuge development. The Study Group concluded that: (1) there has not been sufficient progress to provide a firm scientific, technical or economic basis on which to select one of the three competing AIS processes for full-scale engineering development at this time; and (2) however, should budgetary restraints or other factors force such a selection, we believe that the evaluation process that is being carried out by the PEB provides the best basis available for making a decision. The Study Group recommended that: (1) any decisions on AIS processes should include a comparison with gas centrifuge processes, and should not be made independently from the plutonium isotope program; (2) in evaluating the various enrichment processes, all applicable costs (including R and D and sales overhead) and an appropriate discounting approach should be included in order to make comparisons on a private industry basis; (3) if the three AIS programs continue with limited resources, the work should be reoriented to focus only on the most pressing technical problems; and (4) if a decision is made to develop the Atomic Vapor Laser Isotope Separation process, the solid collector option should be pursued in parallel to alleviate the potential program impact of liquid collector thermal control problems

  16. Continuous Fiber Wound Ceramic Composite (CFCC) for Commercial Water Reactor Fuel. Technical progress report for period ending April 1, 2000

    2000-01-01

    Our program began on August 1, 1999. As of April 1, 2000, the progress has been in materials selection and test planning. Three subcontracts are in place (McDermott Technologies Inc. for continuous fiber reinforced ceramic tubing fabrication, Swales Aerospace for LOCA testing of tubes, and Massachusetts Institute of Technology for In Reactor testing of tubes). With regard to materials selection we visited McDermott Technologies Inc. a number of times, including on February 23, 2000 to discuss the Draft Material Selection and Fabrication Report. The changes discussed at this meeting were implemented and the final version of this report is attached (attachment 1). McDermott Technologies Inc. will produce one type of tubing: Alumina oxide (Nextel 610) fiber, a carbon coating (left in place), and alumina-yttria matrix. A potentially desirable CFCC material of silicon carbide fiber with spinel matrix was discussed. That material selection was not adopted primarily due to material availability and cost. Gamma Engineering is exploring the available tube coatings at Northwestern University as a mechanism for reducing the permeability of the tubes, and thus, will use coating as a differentiating factor in the testing of tubing in the LOCA test as well as the In-Reactor Test. The conclusion of the Material Selection and Fabrication Report lists the possible coatings under evaluation. With regard to Test Planning, the MIT and Swales Aerospace have submitted draft Test Plans. MIT is attempting to accommodate an increased number of test specimens by evaluating alternative test configurations. Swales Aerospace held a design review at their facilities on February 24, 2000 and various engineering alternatives and safety issues were addressed. The final Test Plans are not expected until just before testing begins to allow for incorporation of changes during ''dry runs.''

  17. A characterization and evaluation of coal liquefaction process streams. Quarterly technical progress report, July 1--September 30, 1995

    Robbins, G.A.; Brandes, S.D.; Winschel, R.A.; Burke, F.P.

    1995-12-01

    The objectives of this project are to support the DOE direct coal liquefaction process development program and to improve the useful application of analytical chemistry to direct coal liquefaction process development. Independent analyses by well-established methods will be obtained of samples produced in direct coal liquefaction processes under evaluation by DOE. Additionally, analytical instruments and techniques which are currently underutilized for the purpose of examining coal-derived samples will be evaluated. The data obtained from this study will be used to help guide current process development and to develop an improved data base on coal and coal liquids properties. A sample bank will be established and maintained for use in this project and will be available for use by other researchers. The reactivity of the non-distillable resids toward hydrocracking at liquefaction conditions (i.e., resid reactivity) will be examined. From the literature and data experimentally obtained, a mathematical kinetic model of resid conversion will be constructed. It is anticipated that such a model will provide insights useful for improving process performance and thus the economics of direct coal liquefaction. Some of the contract activities for this quarter are: We completed many of the analyses on the 81 samples received from HTI bench-scale run CMSL-9, in which coal, coal/mixed plastics, and coal/high density polyethylene were fed; Liquid chromatographic separations of the 15 samples in the University of Delaware sample set were completed; and WRI completed CP/MAS {sup 13}C-NMR analyses on the Delaware sample set.

  18. Sequential purification and crystal growth for the production of low cost silicon substrates. Quarterly technical progress report No. 1, 15 September 1979-31 December 1979

    Liaw, M.; Secco, F.; Ingle, B.; Down, D.

    1980-02-01

    Over the past several years, Motorola's Materials Technology Laboratory (MTL), has been conducting several projects with goals directed at the production of high quality low cost silicon crystals. One of the projects which is being investigated is the direct purification of MG-Si. A unique characteristic of the approach used by this project is the use of a crystal puller to perform both purification and crystal growth. Sequential steps of purification were taken. By the completion of this series of purification, the purified MG-Si melt will be further purified by impurity redistribution using ingot pulling. The final purified silicon will be in an ingot form of desired dimensions for slicing into silicon sheets. The sequential steps of purification include: (1) leaching of MG-Si charge, (2) phase separation, (3) reactive gas treatment, (4) liquid-liquid extraction (called Slagging), and (5) purification by redistribution of impurities using ingot pulling. Progress on items (1) and (2) is reported. (WHK)

  19. Features of formation spirituality pictures of the world in youth in in the era of information-highlytechnological scientific and technical progress

    N. V. Polishchuk

    2016-06-01

    Full Text Available In clause necessity of formation of a spiritual picture of the world, anthropocosmos at young generation at the present stage of development much crisis world and, including, the Ukrainian society is proved. In the article the necessity of formation of anthropocosmos-spiritual picture of the world at young generation at the present stage of development bagalicious the world and, in particular, of the Ukrainian society. The proposed definition of new terms: anthropocosmos is a spiritual picture of the world, anthropocosmic spirituality, anthropocosmic worldview and other anthropocentric concepts and definitions in contemporary philosophical and pedagogical discourse. The presented model of the formation of anthropocosmos-spiritual worldview of the young generation in the information and high-tech scientific and technical progress and the author’s interpretation of its philosophical, educational, pedagogical and spiritual essence. It is proved, that having generated in consciousness of the young man a anthropocosmos-spiritual picture of the world, will allow it in conditions of inevitable crash in the near future of a human civilization, if it will not solve present global-civilizational crises and will not avoid geocosmic accidents, to understand sense space-ekzoplanete lives which will be esclusivi, and, therefore, crisis-free, conflict-free, comprehensive and meaningful, anthropocosmos-highly spiritual (divine M. Berdyaev, and, therefore, progressive and virtually eternal as the life of society, which is composed of such anthropocosmos educated individuals. Solved zagalnoosvitnioi sense anthropocosmos spiritual world picture, which is to solve the problem of the choice of life strategies of mankind, the search for new ways of civilization development, in particular, resettlement anthropocosmos-conscious part of humanity for exoplanets space with the aim of preserving the gene pool of humanity and creation of human cosmically

  20. The production of fuels and chemicals from food processing wastes using a novel fermenter separator. Annual progress report, January 1991--December 1991

    Dale, M.C.; Venkatesh, K.V.; Choi, Hojoon; Moelhman, M.; Saliceti, L.; Okos, M.R.; Wankat, P.C.

    1991-12-01

    During 1991, considerable progress was made on the waste utilization project. Two small Wisconsin companies have expressed an interest in promoting and developing the ICRS technology. Pilot plant sites at (1) Hopkinton, IA, for a sweet whey plant, and Beaver Dam WI, for an acid whey site have been under development siting ICRS operations. The Hopkinton, IA site is owned and operated by Permeate Refining Inc., who have built a batch ethanol plant across the street from Swiss Valley Farms cheddar cheese operations. Permeate from Swiss Valley is piped across to PRI. PRI has signed a contract to site a 300--500,000 gallon/yr to ICRS pilot plant. They feel that the lower labor, lower energy, continuous process offered by the ICRS will substantially improve their profitability. Catalytics, Inc, is involved with converting whey from a Kraft cream cheese operation to ethanol and yeast. A complete project including whey concentration, sterilization, and yeast growth has been designed for this site. Process design improvements with the ICRS focussed on ethanol recovery techniques during this year`s project. A solvent absorption/extractive distillation (SAED) process has been developed which offers the capability of obtaining an anhydrous ethanol product from vapors off 3 to 9% ethanol solutions using very little energy for distillation. Work on products from waste streams was also performed. a. Diacetyl as a high value flavor compound was very successfully produced in a Stirred Tank Reactor w/Separation. b. Yeast production from secondary carbohydrates in the whey, lactic acid, and glycerol was studied. c. Lactic acid production from cellulose and lactose studies continued. d. Production of anti-fungal reagents by immobilized plant cells; Gossypol has antifungal properties and is produced by G. arboretum.

  1. The plasma centrifuge: A compact, low cost, stable isotope separator. Phase 2 final technical report, September 15, 1991 - September 14, 1995

    Guss, W.

    1996-01-01

    Enriched stable isotopes are required for production of radionuclides as well as for research and diagnostic uses. Science Research Laboratory (SRL) has developed a plasma centrifuge for moderate throughput of enriched stable isotopes, such as 13 C, 17 O, 18 O, and 203 Tl, for medical as well as other applications. Dwindling isotope stocks have restricted the use of enriched isotopes and their associated labeled organic molecules in medical imaging to very few research facilities because of high costs of isotope separation. With the introduction of the plasma centrifuge separator, the cost per separated gram of even rarely occurring isotopes (≤ 1% natural abundance) is potentially many times lower than with other separation technologies (cryogenic distillation and calutrons). The centrifuge is a simple, robust, pulsed electrical discharge device that has successfully demonstrated isotope separation of small (mg) quantities of 26 Mg. Based on the results of the Phase 2 program, modest enhancements to the power supplies and cooling systems, a centrifuge separator will have high repetition rate (60 pps) and high duty cycle (60%) to produce in one month kilogram quantities of highly enriched stable isotopes. The centrifuge may be used in stand-alone operation or could be used as a high-throughput pre-separation stage with calutrons providing the final separation

  2. Progress report on nuclear science and technology in China (Vol.3). Proceedings of academic annual meeting of China Nuclear Society in 2013, No.4--isotope separation sub-volume

    2014-05-01

    Progress report on nuclear science and technology in China (Vol. 3) includes 37 articles which are communicated on the third national academic annual meeting of China Nuclear Society. There are 10 books totally. This is the fourth one, the content is about isotope separation sub-volume

  3. Mesonic atoms. Technical progress report

    Kunselman, R.

    1981-01-01

    Research on mesic atoms during 1981 is reported. This includes measurement of x-rays from pionic hydrogen and pionic deuterium; muonic K, L, and M x-ray spectra of mercury 199 and mercury 201; and pionic chromium 54, scandium 45, vanadium 51, manganese 55, and iron

  4. 1986 PAEC Technical progress report

    1987-01-01

    Presented are on-going research and development projects of the Philippine Atomic Energy Commission in the fields of agriculture and natural resources, health and nutrition, supportive research, nuclear applications services, industry and energy, and other scientific and technological services and information system. (ELC)

  5. IRIS Final Technical Progress Report

    M. D. Carelli

    2003-11-03

    OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed in the first four years of IRIS, from October 1999 to October 2003. It provides a panoramic of the project status and design effort, with emphasis on the current status, since two previous reports have very extensively documented the work performed, from inception to early 2002.

  6. Exotic atoms. Technical progress report

    Kunselman, R.

    1994-01-01

    The experiments use a variety of hydrogen isotopic mixtures to form solid targets for muons to produce muonic hydrogen isotope atoms that escape into vacuum. The method relies on transfer of the muon from a proton to either a deuteron or a triton. The resulting muonic deuterium or muonic tritium will not immediately thermalize because of the very low elastic cross sections (RT effect), and are emitted from the surface of the layer. A second solid hydrogen isotopic target is produced downstream on which the muonic hydrogen atom can react. Measurements which detect decay electrons, muonic x-rays, and fusion products have been used to study the processes of energy dependence of transfer, production rates, and muon molecular formation. The processes include muon catalyzed fusion of muonic tritium with deuterium which is the most possible candidate for energy production fusion. Our interest is the nuclear physics reaction rates and to use the muonic hydrogen isotopes in vacuum for energy level measurements. The method uses time of flight and is reminiscent of double scattering experiments. Two other experiments are in the development stages. First to measure the energy dependence of the Ramsauer-Townsend cross section in tritium where it has not been measured. The measurements would be compared to deuterium and calculations. Second, kaonic atoms, hypernuclei, and kaon-nucleon scattering at DAPHNE

  7. TECHNICAL AND ECONOMIC EVALUATION OF THE SEPARATION OF LIGHT OLEFINS (ETHYLENE AND PROPYLENE) BY USING p-COMPLEXATION WITH SILVER SALTS

    Salgado-Gordon, Hernando-José; Valbuena-Moreno, Gleidy

    2011-01-01

    ABSTRACT Conventional processes for separation of ethylene and propylene until reaching petrochemical grade are energy intensive. Therefore, alternative separation methods, such as chemical affinity based technologies, are an interesting alternative for designing more sustainable processes. p-Complexation of the silver ion (Ag+) is one of these technologies. In this study, p-complexation is compared to the conventional technologies from process and economic points of view, in order to determi...

  8. Improved estimates of separation distances to prevent unacceptable damage to nuclear power plant structures from hydrogen detonation for gaseous hydrogen storage. Technical report

    1994-05-01

    This report provides new estimates of separation distances for nuclear power plant gaseous hydrogen storage facilities. Unacceptable damage to plant structures from hydrogen detonations will be prevented by having hydrogen storage facilities meet separation distance criteria recommended in this report. The revised standoff distances are based on improved calculations on hydrogen gas cloud detonations and structural analysis of reinforced concrete structures. Also, the results presented in this study do not depend upon equivalencing a hydrogen detonation to an equivalent TNT detonation. The static and stagnation pressures, wave velocity, and the shock wave impulse delivered to wall surfaces were computed for several different size hydrogen explosions. Separation distance equations were developed and were used to compute the minimum separation distance for six different wall cases and for seven detonating volumes (from 1.59 to 79.67 lbm of hydrogen). These improved calculation results were compared to previous calculations. The ratio between the separation distance predicted in this report versus that predicted for hydrogen detonation in previous calculations varies from 0 to approximately 4. Thus, the separation distances results from the previous calculations can be either overconservative or unconservative depending upon the set of hydrogen detonation parameters that are used. Consequently, it is concluded that the hydrogen-to-TNT detonation equivalency utilized in previous calculations should no longer be used

  9. Progress in the domain of emissions tracking and environment radioactivity monitoring - Proceedings of the technical days organised by the SFRP Environment Section

    Calmet, Dominique; Calvez, Marianne; Rivasseau, Corinne Cea; Monfort, Marguerite; Manificat, Guillaume; Pierrard, Olivier; Couvez, Celine; Masson, Olivier; Bruno, Valerie; Renaud, Philippe; Genova, Zhana; Reynal, Nathalie; Le Coz, Eric; Tchilian, Nathalie; Diana, Jean-Jacques; Beguinel, Philippe; Cortes, Pierre; Puydarrieux, Stephane; Brun, Thierry; Devin, Patrick; Clavel, Benoit; Hemidy, Pierre-Yves; Gontier, Gilles; Delloye, Thierry; Mailliat, Alain; Ferreri, Giovanni; LECLERC, Elisabeth

    2015-11-01

    The Environment Section of the French Society of Radiation Protection (SFRP) organized a technical meeting on the progress made in the domain of emissions tracking and environment radioactivity monitoring. This document brings together the abstracts and the presentations (slides) of the different talks given at the meeting: 1 - Environment monitoring at the global, national and local scale: historical overview (Dominique CALMET, CEA); 2 - Evolution of radioactivity monitoring in the environment from 1960 to the present day (Guillaume MANIFICAT, IRSN); 3 - Euratom's legal framework (Zhana GENOVA, CTE); 4 - Main regulatory changes during the last decade (Nathalie REYNAL, ASN); 5 - Progress of standardization works on radioactive effluent emissions control and environment monitoring (Philippe BEGUINEL, BNEN); 6 - From operators' self-monitoring to ASN's inspections: a many components control system (Eric LE COZ, ASN); 7 - Control of effluents and emissions management at CEA Centres (Marianne CALVEZ, CEA); 8 - Liquid and gaseous effluents of ITER experimental facility: description and impacts (Pierre CORTES, IO); 9 - Effluents and emissions management strategy at AREVA NC La Hague facility (Stephane PUYDARRIEUX, AREVA); 10 - Radioactive effluents from nuclear facilities ongoing deconstruction: from dimensioning to real effluents (Benoit CLAVEL, EDF); 11 - Radionuclides decontamination process for liquid effluents using micro-algae at the laboratory scale (Corinne RIVASSEAU, CEA); 12 - Radioactive effluents from nuclear medicine services: management, monitoring and impact measurement methods (Nathalie TCHILIAN, ASN); 13 - Evolution history of effluents management and environment monitoring at the Solvay La Rochelle site (Thierry DELLOYE, SOLVAY); 14 - Different international approaches in effluents management and monitoring: example of French and German gaseous effluents - regulation, analyses, accounting rules (Jean-Jacques DIANA, ASN); 15 - Environment

  10. Biology Division progress report, June 1, 1980-July 31, 1982

    1982-12-01

    Highlights of progress for the period June 1980 through July 1982 are summarized. Discussions of projects are presented under the following headings: molecular and cellular sciences; cellular and comparative mutagenesis; mammalian genetics and teratology; toxicology; and carcinogenesis. In addition this report includes an outline of educational activities. Separate abstracts have been prepared for individual technical reports for inclusion in the Energy Data Base. (RJC)

  11. Materials testing and requirements for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1974--May 1, 1975

    Andrade, J.D.; Coleman, D.L.; Leigh, A.; Hufferd, W.L.

    1975-01-01

    Progress on the materials research and development effort for the ERDA-sponsored nuclear-powered artificial heart program is presented. Progress made during the first three years on hydrogel grafting and biological studies is summarized. Progress during the fourth year on studies of implanted artificial hearts, development of albumin surfaces, and in vitro mechanical studies is presented. (U.S.)

  12. Final Technical Report for the Energy Frontier Research Center Understanding Charge Separation and Transfer at Interfaces in Energy Materials (EFRC:CST)

    Vanden Bout, David A. [Univ. of Texas, Austin, TX (United States)

    2015-09-14

    Our EFRC was founded with the vision of creating a broadly collaborative and synergistic program that would lead to major breakthroughs in the molecular-level understanding of the critical interfacial charge separation and charge transfer (CST) processes that underpin the function of candidate materials for organic photovoltaic (OPV) and electrical-energy-storage (EES) applications. Research in these energy contexts shares an imposing challenge: How can we understand charge separation and transfer mechanisms in the presence of immense materials complexity that spans multiple length scales? To address this challenge, our 50-member Center undertook a total of 28 coordinated research projects aimed at unraveling the CST mechanisms that occur at interfaces in these nanostructured materials. This rigorous multi-year study of CST interfaces has greatly illuminated our understanding of early-timescale processes (e.g., exciton generation and dissociation dynamics at OPV heterojunctions; control of Li+-ion charging kinetics by surface chemistry) occurring in the immediate vicinity of interfaces. Program outcomes included: training of 72 graduate student and postdoctoral energy researchers at 5 institutions and spanning 7 academic disciplines in science and engineering; publication of 94 peer-reviewed journal articles; and dissemination of research outcomes via 340 conference, poster and other presentations. Major scientific outcomes included: implementation of a hierarchical strategy for understanding the electronic communication mechanisms and ultimate fate of charge carriers in bulk heterojunction OPV materials; systematic investigation of ion-coupled electron transfer processes in model Li-ion battery electrode/electrolyte systems; and the development and implementation of 14 unique technologies and instrumentation capabilities to aid in probing sub-ensemble charge separation and transfer mechanisms.

  13. A technical review of liquid/liquid and solid/liquid separation equipment in the field of nuclear-fuel reprocessing

    Vassallo, G.

    1981-01-01

    Liquid/liquid extraction is generally accepted as the preferred method in nuclear-fuel reprocessing. However, although many types of liquid/liquid contactors are available, only a few meet the stringent specifications set by the nuclear industry. This report discusses the criteria for contactor selection and then reviews the most important types, namely packed columns, pulsed columns, mixer-setters and centrifugal contactors. Finally, a short section concerned with solid/liquid separations is included because of the possible deleterious effects caused by solids in liquid/liquid contactors

  14. An alternative beam line at the U-400 M cyclotron for RIB separation and transport to the FOBOS spectrometer (The technical proposal)

    Majdikov, V.Z.; Bashevoj, V.V.

    1998-01-01

    The first order ion-optic calculations performed together with the graphical modeling permits us to propose a new variant of the beam-transport line from the backside of the U-400M cyclotron to the FOBOS spectrometer. This beam line could be built in a rather short time without large financial expenditures from available magnetic and vacuum elements. The new beam line could even be considered as an economic alternative to the existing beam line and as a RIB separator. This work is the result of the pre-design R and D aimed to develop the U-400M cyclotron facilities for the RIB experiments performance with the FOBOS spectrometer

  15. Studies in matter antimatter separation and in the origin of lunar magnetism. Annual progress report, 1 Sep 1974--31 Aug 1975

    Barker, W.A.; Greeley, R.; Parkin, C.; Aggarwal, H.; Schultz, P.

    1975-01-01

    A progress report covering lunar and planetary research is introduced. Data cover lunar ionospheric models, lunar and planetary geology, and lunar magnetism. Wind tunnel simulations of Mars aeolian problems and a comparative study of basaltic analogs of Lunar and Martial volcanic features was discussed

  16. Progress Report Oct to Dec 1975(2)

    1976-01-01

    Progress report NO. 2 of Tehran Nuclear Research Centre outlines a brief description of the progress made in each section of the centre. A complete list of dissertations for Master's degrees studied at the Nuclear Research Centre and a list of new technical employee are given at the beginning of the report. Research activities in the third section include, isotope separation, laser research, radiation chemistry, reactor management, environmental research, neutron physics, reactor engineering, and nuclear medicine. The fourth section deals with education and training; technical support and health physics are discussed in sections five and six respectively

  17. Missouri local technical assistance program at Missouri University of Science and Technology (formerly University of Missouri--Rolla) : annual progress report January-December 2007.

    2009-02-01

    This annual report is a summary of the activities during 2007 for the Missouri Local Technical Assistance Program (Missouri LTAP), which is located at Missouri University of Science and Technology. The report highlights Missouri LTAPs performance ...

  18. The development of coal-based technologies for Department of Defense facilities. Volume 2, Appendices. Semiannual technical progress report, September 28, 1994--March 27, 1995

    Miller, B.G.; Bartley, D.A.; Hatcher, P.

    1996-01-01

    This semiannual progress report contains the following appendices: description of the 1,000 lb steam/h watertube research boiler; the Pennsylvania CGE model; Phase II, subtask 3.9 coal market analysis; the CGE model; and sector definition

  19. TECHNICAL COORDINATION

    A. Ball and W. Zeuner

    2011-01-01

    In this report we will review the main achievements of the Technical Stop and the progress of several centrally-managed projects to support CMS operation and maintenance and prepare the way for upgrades. Overview of the extended Technical Stop  The principal objectives of the extended Technical Stop affecting the detector itself were the installation of the TOTEM T1 telescopes on both ends, the readjustment of the alignment link-disk in YE-2, the replacement of the light-guide sleeves for all PMs of both HFs, and some repairs on TOTEM T2 and CASTOR. The most significant tasks were, however, concentrated on the supporting infrastructure. A detailed line-by-line leak search was performed in the C6F14 cooling system of the Tracker, followed by the installation of variable-frequency drives on the pump motors of the SS1 and SS2 tracker cooling plants to reduce pressure transients during start-up. In the electrical system, larger harmonic filters were installed in ...

  20. Progress of MCFC stack technology at Toshiba

    Hori, M.; Hayashi, T.; Shimizu, Y. [Toshiba Corp., Tokyo (Japan)

    1996-12-31

    Toshiba is working on the development of MCFC stack technology; improvement of cell characteristics, and establishment of separator technology. For the cell technology, Toshiba has concentrated on both the restraints of NiO cathode dissolution and electrolyte loss from cells, which are the critical issues to extend cell life in MCFC, and great progress has been made. On the other hand, recognizing that the separator is one of key elements in accomplishing reliable and cost-competitive MCFC stacks, Toshiba has been accelerating the technology establishment and verification of an advanced type separator. A sub-scale stack with such a separator was provided for an electric generating test, and has been operated for more than 10,000 hours. This paper presents several topics obtained through the technical activities in the MCFC field at Toshiba.

  1. Rapid chemical separations

    Trautmann, N

    1976-01-01

    A survey is given on the progress of fast chemical separation procedures during the last few years. Fast, discontinuous separation techniques are illustrated by a procedure for niobium. The use of such techniques for the chemical characterization of the heaviest known elements is described. Other rapid separation methods from aqueous solutions are summarized. The application of the high speed liquid chromatography to the separation of chemically similar elements is outlined. The use of the gas jet recoil transport method for nuclear reaction products and its combination with a continuous solvent extraction technique and with a thermochromatographic separation is presented. Different separation methods in the gas phase are briefly discussed and the attachment of a thermochromatographic technique to an on-line mass separator is shown. (45 refs).

  2. Luminescence process, refractory stabilities, and new novel electronic states: scanning chemical reactions and novel products for laser induced isotope separation. Progress report, December 1, 1975--July 15, 1976

    Gole, J.L.

    1976-08-01

    The formulation, development, and use of versatile oven systems for high temperature metal vaporization at temperatures in excess of 2000 0 C are discussed. Refinements of an apparatus appropriate for the production and study of small metal aggregates M/sub n/(2 less than or equal to n less than or equal to 6) are discussed at length. Improvements in the argon ion and nitrogen pumped dye laser systems, and necessary additions for effective interfacing of these dye lasers to the aggregates apparatus are described. Internal calibration standards are discussed. Progress on the production of carbon vapor and the reaction of this vapor with metal atoms and metal dimers to form metal carbides is outlined. Metal sulfide chemistry is discussed. Several specific studies of the luminescence process are outlined. Included in these studies are completed work on aluminum oxidation. Studies of germanium and silicon oxidation are outlined, and new investigations of inorganic hydride oxidation are presented. The status of our efforts to form new and novel surfaces via aggregate deposition is outlined. Quantum chemical calculations on small metal aggregates are discussed. The first applications of dynamic laser induced fluorescence to the AlO molecule are presented

  3. Research and development of methods/utilities and rules for managing cooperation for performance improvement in government offices. Second Technical progress report, September 1, 1992--January 31, 1993

    Kurstedt, H.A.

    1993-03-01

    Purpose is to help managers approach their responsibilities proactively, so that they can anticipate problems and take actions to alleviate or eliminate those problems. Continuous performance improvement, the philosophy behind total quality management, requires working cooperatively to do a little better each day. The most effective tools are working through a closed set of 9 methods: setting expectations, charting, defining indicators and standards, collecting and logging data, converting data to information, organizing and presenting information, reviewing status and progress, self-management, and appraising. In addition, there are 8 rules: focus on what you can do, supply physical evidence of progress, pay attention to detail, inspect (don`t expect), review progress routinely and frequently, face ``success/fail`` squarely, communicate crisply, and conduct honest, open appraisals. Scope and plans of the draft research plan (study areas) are described.

  4. Progress in resolving open design issues from the ODR. Report by the Director. ITER technical advisory committee meeting, 25-27 June 2000, St. Petersburg

    2000-01-01

    This report presents progress in resolving open design issues from the ITER-FEAT Outline Design Report and is not repeating the ODR information but concentrates on the specific issues and the progress towards their resolution. It includes some aspects of the Physics analysis (inductive operation scenario and sensitivity analysis, ion heating, possibility of high Q and ignition operation, divertor physics), Magnets (TF coil loads, inductive flux generation, conductor design issues), Vessel/in Vessel (manifolding of blanket coolant, vacuum vessel design development, design implications of divertor material choice), Buildings and Plant services, Operation and Safety

  5. Attitudes towards technical progress. Acceptance of technology in national and international comparison. Einstellungen zum technischen Fortschritt. Technikakzeptanz im nationalen und internationalen Vergleich

    Jaufmann, D.; Kistler, E. (Internationales Inst. fuer Empirische Sozialoekonomie (INIFES), Gemeinnuetzige GmbH, Leitershofen (Germany)) (eds.)

    1991-01-01

    Engineering, new technologies, science and attitudes of the public are important determinants for influencing the development and the state of a country. Problems concerning the acceptance of technical projects and developments also can be the scapegoat for other, deeper conflicts in society - they are important, and increasingly a social and political challenge. The book supplies empirically fundamental and interdisciplinary prerequisites for future debates. The contributions were presented at a public seminar in January 1989. (orig./HSCH).

  6. Progress report for '89

    Podest, M.

    1990-08-01

    The 1989 Progress Report presents the most important scientific and technical achievements of the Nuclear Research Institute's research work. Some specialized products prepared at or fabricated by the NRI are mentioned as well. (author). 24 figs., 8 tabs., 101 refs

  7. [Conduct theoretical and experimental research programs in high energy physics]: Technical progress, Appendix A-2, FTP/A, Item 20,f

    1986-01-01

    Progress is reported in these areas: neutrino physics; nucleon decay and the intrinsic properties of neutrinos; the D-zero experiment; QCD jet physics and ultrarelativistic nuclear physics; the Colliding Detector at Fermilab; rare kaon decay; the Anomalous Single Photon detector at SLAC; particle theory; neutrino astrophysics and cosmology; and operations and support services

  8. Materials testing and requirement for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1975--May 30, 1976. [BIOMER and AVCOTHANE

    Andrade, J. D.; Hufferd, W. L.; Lyman, D. J.

    1976-01-01

    The two materials currently being used for the artificial heart fabrication are BIOMER and AVCOTHANE. BIOMER is a polyether urethane polymer. AVCOTHANE is a proprietary polyurethane/polydimethylsiloxane polymer blend. Research progress on the chemical degradation, mechanical strength, and blood compatibility is reported. (TFD)

  9. A "Fear" Studies Perspective and Critique: Analyzing English and Stengel's Progressive Study of Fear and Learning in "Education Theory." Technical Paper No. 37

    Fisher, R. Michael

    2011-01-01

    The author critiques the progressive approach of two contemporary educational philosophers (English and Stengel) on the topic of fear and learning. Using a postmodern integral approach, this article examines the tendency of reductionism, individualism, and psychologism as part of a hegemonic liberalism and modernism in discourses on fear and…

  10. GPHS-RTGs in support of the Cassini Mission. Semi-annual technical progress report, April 3, 1995--October 1, 1995

    1995-01-01

    This document is the April-October 1995 Progress Report on the Cassini RTG Program. Nine tasks are summarized; (1) Spacecraft integration and liason, (2) Engineering support, (3) Safety, (4) Unicouple fabrication, (5) ETG fabrication, assembly, and test, (6) Ground support equipment, (7) RTG shipping and launch support, (8) Design, reviews, and mission applications, and (9) Project management, QA, contract changes, and material acquisitions

  11. Materials testing and requirement for the ERDA nuclear-powered artificial heart. Technical progress report, July 15, 1975--May 30, 1976

    Andrade, J.D.; Hufferd, W.L.; Lyman, D.J.

    1976-01-01

    The two materials currently being used for the artificial heart fabrication are BIOMER and AVCOTHANE. BIOMER is a polyether urethane polymer. AVCOTHANE is a proprietary polyurethane/polydimethylsiloxane polymer blend. Research progress on the chemical degradation, mechanical strength, and blood compatibility is reported

  12. Bioremediation of mixed microbial mats: System development of mixed contaminants for application at the Savannah River Site. Annual technical progress report, October 1, 1995--September 30, 1996

    Bender, J.; Phillips, P.

    1996-01-01

    The fundamental objective of this project is to develop and field test the mixed microbial mat bioremediation system for decontamination of target sites at SRS. Although microbial mats have performed well in several pilot projects in the past, atypical problems and site characteristics at SRS demand special field designs. In the interest of designing a pilot and locating it at an appropriate site, the project investigators have worked closely with the technical staff at the SREL. We have concluded that the diverse characteristics of contaminations at SRS may dictate testing several pilot designs during the course of this project

  13. Evaluation and capacity building to improve precollege science and mathematics achievement in the US: 10 CFR, Part 605. Technical progress report, June--December 1992

    1992-12-31

    The National Center for Improving Science Education has undertaken activities to achieve evaluation goals for DOE`s Precollege programs: develop means to determine program quality; develop means for determining the contribution of DOE precollege programs to both teacher enhancement and student achievement; provide evaluation designs and instruments and reports of program quality and impact; and strengthen both DOE`s and the Labs` capacity to do both short- and long-term planning as well as deliver effective programs and evaluation. Appendices include evaluation/technical assistance report, profiling teacher research participation and teacher development programs, teacher surveys, impact assessment design, and teacher research participation programs anecdotes for 8 labs.

  14. Critical experiments supporting underwater storage of tightly packed configurations of spent fuel pins. Technical progress report, January 1-March 31, 1981

    Hoovler, G.S.; Baldwin, M.N.

    1981-04-01

    Critical experiments are in progress on arrays of 2 1/2% enriched UO 2 fuel pins simulating underwater pin storage of spent power reactor fuel. Pin storage refers to a spent fuel storage concept in which the fuel assemblies are dismantled and the fuel pins are tightly packed into specially designed canisters. These experiments are providing benchmark data with which to validate nuclear codes used to design spent fuel pin storage racks

  15. Search for neutrino oscillations and measurements of neutrino-nucleus cross sections. Technical progress report, 16 January 1985-15 October 1985

    Koetke, D.D.

    1985-01-01

    Progress is reported in these areas: work done at LANL on experiment E764, including beam line modification, new target installation, system testing, on-line software development, beam tuning, and data acquisition; neutrino Monte Carlo program development; flux calculations for the DC modified torroidal pion focussing device for the low energy decay-in-flight neutrino source; and prototype preparation for a large modular segmented detector

  16. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 28 March 1994--25 September 1994

    1994-01-01

    The progress on the radioisotope generators and ancillary activities is described. This report is organized by program task as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; design, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contractor acquired government owned property (CAGO) acquisition

  17. TECHNICAL COORDINATION

    Austin Ball

    Summary of progress since last CMS week. Ten years of construction work have been completed. CMS is closed, in very close to the ideal low luminosity configuration, and performed well in the first tests with LHC beam. Behind this encouraging news is the story of a summer of intense commitment by many teams (from the collaboration and 3 CERN departments) working together, against the clock and despite many minor setbacks, to ensure that the experiment was ready to play a leading role in the excitement of September 10. Following beampipe bakeout and refill with pure neon, a magnificent effort by the ECAL group and the pt 5 technical crew made it possible to install and commission all 4 ECAL endcap Dees before the end of August. In the shadow of this activity, the barrel and forward pixel trackers and part of the beam monitoring were installed within the vac tank. The pt 5 technical teams then succeeded in safely removing the 20t installation tables and their support blocks from beneath the already installed ...

  18. Separating oil from water

    Webb, C

    1991-04-11

    The technology available to deal with oil spills has assumed many new faces in recent years. Methods of dealing with small-scale pollution in the process industries and vast oil slicks such as that in the Gulf have developed in parallel. The progress being made in finding new means of separating oil from water is reported and the relative merits of bioremediation, hydrocylones, horizontal separators and gas flotation are discussed. (author).

  19. (Pittsburgh Energy Technology Center): Quarterly technical progress report for the period ending June 30, 1987. [Advanced Coal Research and Technology Development Programs

    None

    1988-02-01

    Research programs on coal and coal liquefaction are presented. Topics discussed are: coal science, combustion, kinetics, surface science; advanced technology projects in liquefaction; two stage liquefaction and direct liquefaction; catalysts of liquefaction; Fischer-Tropsch synthesis and thermodynamics; alternative fuels utilization; coal preparation; biodegradation; advanced combustion technology; flue gas cleanup; environmental coordination, and technology transfer. Individual projects are processed separately for the data base. (CBS)

  20. TECHNICAL COORDINATION

    Austin Ball

    2013-01-01

      Since the last report, much visible progress has been made, as the LS1 programme approaches the halfway point. From early October, technical and safety shift-crew have been present around the clock, allowing detectors to stay switched on overnight, ensuring that safety systems are operational and instructions for non-expert shift-crew are clear. LS1 progress Throughout the summer, whilst the solenoid vacuum tank and YB0 surfaces were accessible, an extensive installation programme took place to prepare for Tracker colder operation and the PLT installation, in 2014, the Phase 1 Pixel Tracker installation, in 2016–’17, and the HCAL Phase 1 upgrade completion, ending in LS2. This included pipework for N2 or dry air to flush the Tracker bulkhead region, many sensors to monitor temperature and dew point in the Tracker and its service channels, heating wires outside the Tracker cooling bundles, supports for the new vacuum-jacketed, concentric, CO2 Pixel cooling lines, the PLT cool...

  1. Progress in design, research and development and testing of safety systems for advanced water cooled reactors. Proceedings of a technical committee meeting

    1996-04-01

    The meeting covered the following topics: Developments in design of safety-related heat removal components and systems for advanced water cooled reactors; status of test programmes on heat removal components and systems of new designs; range of validity and extrapolation of test results for the qualification of design/licensing computer models and codes for advanced water cooled reactors; future needs and trends in testing of safety systems for advanced water cooled reactors. Tests of heat removal safety systems have been conducted by various groups supporting the design, testing and certification of advanced water cooled reactors. The Technical Committee concluded that the reported test results generally confirm the predicted performance features of the advanced designs. Refs, figs, tabs

  2. Progress in design, research and development and testing of safety systems for advanced water cooled reactors. Proceedings of a technical committee meeting

    NONE

    1996-04-01

    The meeting covered the following topics: Developments in design of safety-related heat removal components and systems for advanced water cooled reactors; status of test programmes on heat removal components and systems of new designs; range of validity and extrapolation of test results for the qualification of design/licensing computer models and codes for advanced water cooled reactors; future needs and trends in testing of safety systems for advanced water cooled reactors. Tests of heat removal safety systems have been conducted by various groups supporting the design, testing and certification of advanced water cooled reactors. The Technical Committee concluded that the reported test results generally confirm the predicted performance features of the advanced designs. Refs, figs, tabs.

  3. A methodology for the analysis and selection of alternatives for the disposition of surplus plutonium. Quarterly technical progress report, April 1, 1995--June 30, 1995

    Mulder, R.

    1995-01-01

    The Office of Fissile Materials Disposition is currently involved in the development of a comprehensive approach to the long-term storage and disposition of fissile materials. A major objective of this effort is to provide a framework for US efforts to prevent the proliferation of nuclear weapons. This will entail both the elimination of excess highly enriched uranium and plutonium, and the insurance of the highest standards of safety, security, and international accountability. The Office of Fissile Materials Disposition is supporting an Interagency Working Group that has initiated a comprehensive review of alternatives for plutonium disposition which takes into account non-proliferation, economic, technical, institutional, schedule, environmental, and health and safety issues. These alternatives were identified by the development of screening criteria as a guide to the selection of alternatives that best achieve the fissile nuclear material long-term storage and disposition goals of the US Government

  4. 1993 Annual progress report for subsidiary agreement No. 2 (1991--1996) between AECL and US/DOE for a radioactive waste management technical co-operative program

    1993-01-01

    A coordinated research program on radioactive waste disposal is being carried out by the Atomic Energy of Canada Limited and the US Department of Energy. This annual report describes progress in the following eight studies: Fundamental materials investigations; In-situ stress determination; Development of a spent fuel dissolution model; Large block tracer test--Experimental testing of retardation models; Laboratory and field tests of in-situ hydrochemical tools; Cigar Lake--Analogue study, actinide and fission product geochemistry; Performance assessment technology exchange; and Development of multiple-well hydraulic test and field tracer test methods

  5. 1993 Annual progress report for subsidiary agreement No. 2 (1991--1996) between AECL and US/DOE for a radioactive waste management technical co-operative program

    NONE

    1993-12-31

    A coordinated research program on radioactive waste disposal is being carried out by the Atomic Energy of Canada Limited and the US Department of Energy. This annual report describes progress in the following eight studies: Fundamental materials investigations; In-situ stress determination; Development of a spent fuel dissolution model; Large block tracer test--Experimental testing of retardation models; Laboratory and field tests of in-situ hydrochemical tools; Cigar Lake--Analogue study, actinide and fission product geochemistry; Performance assessment technology exchange; and Development of multiple-well hydraulic test and field tracer test methods.

  6. Evaluation of using cyclocranes to support drilling & production of oil & gas in wetland areas. Sixth quarterly technical progress report, incorporating milestone schedule/status, October 1993--December 1993

    Eggington, W.J.

    1994-04-01

    This report is a progress report on a planned program falling under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. During this period, task 5, subscale tests, and task 7, environmental impacts, were completed. Work was continued on task 10, technology transfer, and the preparation of the final report as part of task 11.

  7. Silicon germanium (SiGe) radioisotope thermoelectric generator (RTG) program for space missions. Nineteenth technical progress report, December 1980-January 1981

    1981-01-01

    Work accomplished during the reporting period on the DOE Silicon Germanium RTG Program, Contract DE-AC01-79ET-32043 is described. This program consists of the following three tasks: multi-hundred watt RTG for the Galileo probe mission; reestablishment of silicon germanium unicouple capability; and general purpose heat source RTG for the international solar polar and Galileo orbiter missions. Details of program progress for each task, including a milestone schedule and a discussion of current problem areas (if any) are presented

  8. Nutrient cycling and productivity of dystrophic lake-bog systems (Part A). Technical progress report, December 1, 1972--September 30, 1975

    Hooper, F.F.

    1975-10-01

    A sampler and an analytical and characterization scheme were developed to investigate the chemical and physical state of iron in a highly stained acid bog lake. Iron fractions were chemically separated by reactivity to bathophenanthroline (BPN) after specific digestion procedures. Physical separation involved anaerobic in situ filtration (450 nm), and in situ dialysis (4.8 nm). This resulted in three size classes: particulate, colloidal, and dissolved. Unlike pH 6-8 lakes, inorganic, nonreactive species of iron [e.g., Fe(OH) 3 ] represent minor amounts of the total iron in North Gate Lake. In situ radiochemical analyses revealed that colloidal sized reactive ferric iron predominates in the oxygenated epilimnion, while dialyzable or dissolved ferrous iron increases with depth. Unlike iron, organic matter is present in a nontransient colloidal state. In acid (pH 4-5) bog lakes ferric iron is not colloidal as an inorganic complex (OH - ), but colloidal as reactive Fe + 3 by complexation with the colloidal organic acids. After thermally induced mixing with anaerobic waters, ferric iron is reduced and dissolved. However, some of the BPN reactive iron remains colloidal suggesting the presence of a residual ferrous organic complex

  9. Development of coal-based technologies for Department of Defense Facilities. Semiannual technical progress report, March 28, 1997--September 27, 1997

    Miller, B.G.; Miller, S.F.; Morrison, J.L. [and others

    1998-01-06

    The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Slurry Fuel Technology, with the aim of developing technologies which can potentially decrease DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Phase I was completed on November 1, 1995. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included performing pilot-scale air toxics (i.e., trace elements and volatile organic compounds) testing and evaluating a ceramic filtering device on the demonstration boiler. Also, a sodium bicarbonate duct injection system was installed on the demonstration boiler. An economic analysis was conducted which investigated the benefits of decreased dependence on imported oil by using new coal combustion technologies. Work related to coal preparation and utilization was primarily focused on preparing the final report. Work in Phase III focused on coal preparation studies, pilot-scale NO{sub x} reduction studies, economic analyses of coal use, and evaluation of deeply-cleaned coal as boiler fuel. Coal preparation studies were focused on continuing activities on particle size control, physical separations, and surface-based separation processes. The evaluation of deeply-cleaned coal as boiler fuel included receiving three cleaned coals from Cyprus-Amax.

  10. Separations by centrifugal phenomena

    Hsu, H.W.

    1981-01-01

    The technical information presented herein emphasizes the uniqueness of the centrifugal separations methodology and pertinent theory for various kinds of centrifugation. The topics are arranged according to gas, liquid, and solid phases, in the order of increasing densities. Much space is devoted to liquid centrifugation because of the importance of this technique in chemical and biological laboratories. Many separational and characterizational examples are illustrated in detail. The material has been divided into 7 chapters entitled: 1) Introduction, 2) Basic Theory of Centrifugation, 3) Gas Centrifuges, 4) Preparative Liquid Centrifuges, 5) Analytical Liquid Centrifuges, 6) Liquid Centrifuges in Practice, and 7) Mechanical Separations by Centrifuges. Separate abstracts have been prepared for each chapter except the introduction

  11. Identification and validation of heavy metal and radionuclide hyperaccumulating terrestrial plant species, Quarterly technical progress report, December 20, 1995--March 20, 1995

    Kochian, L.; Brady, D.; Last, M.; Ebbs, S.

    1995-12-01

    Although the period covered by this progress report began on December 20, 1994, which was the date that DOE approved the Interagency Agreement, the agreement was not approved by USDA until January 9, 1995 and the first scientists working on the project were not hired until February 1, 1995. The first goal of the research supported by the Interagency Agreement is to use hydroponic techniques to identify plant species and genotypes with potential for heavy metal hyperaccumulation for planting on a test site at Silverbow Creek and for radionuclide ({sup 90}Sr and {sup 137}Cs) accumulation on a test site at INEL, Idaho, later this year. The second goal of this research is to identify soil amendment procedures that will enhance the bioavailability of heavy metals and radionuclides in the soil without increasing the movement of the contaminants of concern (COC`s) into the groundwater. Our initial research covered in this report focuses on the first goal.

  12. Development of a thermionic magnicon amplifier at 11.4 GHz. Technical progress report, 16 May 1994--31 December 1995

    Gold, S.H.; Fliflet, A.W.; Manheimer, W.M.

    1995-01-01

    This is a progress report on a four-year research program entitled 'Development of a Thermionic Magnicon Amplifier at 11.4 GHz', which is under way in the Plasma Physics Division of the Naval Research Laboratory (NRL) under Interagency Agreement DE-AI02-94ER40681. This report covers the period 16 May 1994 through 31 December 1995. The magnicon is an advanced microwave tube with potential application to future high gradient linear accelerators such as TeV colliders. Under this program, NRL plans to build and test a thermionic magnicon amplifier tube powered by a 500 kV, 200 A, 10 Hz modulator with a 1 μsec pulse. However, the experiments that were carried out during the period covered by this report were driven by a single-shot Marx generator, and the electron beam was produced from a graphite plasma cathode

  13. Geothermal space/water heating for Mammoth Lakes Village, California. Quarterly technical progress report, 13 December 1976-12 March 1977

    Sims, A.V.; Racine, W.C.

    1977-01-01

    During the second three months of this feasibility study to determine the technical, economic and environmental feasibility of heating Mammoth Lakes Village, California using geothermal energy, the following work was accomplished. A saturation survey of the number and types of space and water heaters currently in use in the Village was completed. Electric energy and ambient temperature metering equipment was installed. Peak heating demand for Mammoth Lakes was estimated for the years 1985, 1990 and 2000. Buildings were selected which are considered typical of Mammoth Lakes in terms of their heating systems to be used in estimating the cost of installing hydronic heating systems in Mammoth. Block diagrams and an order of magnitude cost comparison were prepared for high-temperature and low-temperature geothermal district heating systems. Models depicting a geothermal district heating system and a geothermal-electric power plant were designed, built and delivered to ERDA in Washington. Local input to the feasibility study was obtained from representatives of the State of California Departments of Transportation and Fish and Game, US Forest Service, and Mono County Planning Department.

  14. Implementing waste minimization at an active plutonium processing facility: Successes and progress at technical area (TA) -55 of the Los Alamos National Laboratory

    Balkey, J.J.; Robinson, M.A.; Boak, J.

    1997-12-01

    The Los Alamos National Laboratory has ongoing national security missions that necessitate increased plutonium processing. The bulk of this activity occurs at Technical Area -55 (TA-55), the nations only operable plutonium facility. TA-55 has developed and demonstrated a number of technologies that significantly minimize waste generation in plutonium processing (supercritical CO{sub 2}, Mg(OH){sub 2} precipitation, supercritical H{sub 2}O oxidation, WAND), disposition of excess fissile materials (hydride-dehydride, electrolytic decontamination), disposition of historical waste inventories (salt distillation), and Decontamination & Decommissioning (D&D) of closed nuclear facilities (electrolytic decontamination). Furthermore, TA-55 is in the process of developing additional waste minimization technologies (molten salt oxidation, nitric acid recycle, americium extraction) that will significantly reduce ongoing waste generation rates and allow volume reduction of existing waste streams. Cost savings from reduction in waste volumes to be managed and disposed far exceed development and deployment costs in every case. Waste minimization is also important because it reduces occupational exposure to ionizing radiation, risks of transportation accidents, and transfer of burdens from current nuclear operations to future generations.

  15. Simultaneous high-temperature removal of alkali and particulates in a pressurized gasification system. Final technical progress report, April 1981-July 1983

    Mulik, P.R.; Alvin, M.A.; Bachovchin, D.M.

    1983-09-01

    This program is directed at performing experimental and analytical investigations, deriving system designs, and estimating costs to ascertain the feasibility of using aluminosilicate-based getters for controlling alkali in pressurized gasification systems. Its overall objective is to develop a plan for evaluating a scaled-up version of the gettering process as a unit operation or as an integral part of a particulate removal device. This report describes work completed on the four technical program tasks: Thermodynamic projections; Getter Selection and Qualification; System Performance Projections; and Program Definition for Concept Scale-up during the 27-month contract performance period. Work completed on the thermodynamic projections includes a data base update, development of alkali phase diagrams, and system performance projections. Getter selection and qualification efforts involved over 70 kinetic studies in which a leading candidate getter - emathlite - was selected and characterized. System performance projections identified a packed-bed configuration containing relatively large getter pellets as the preferred contacting device for a full-scale unit. For emathlite, we concluded that full-scale unit bed heights of 2 m or less would be required if we assume annual replacement on the basis of bed saturation capacity. Concept scale-up work involved defining the hardware and test program requirements for further development of the emathlite packed-bed system. 56 references, 80 figures, 74 tables.

  16. Implementing waste minimization at an active plutonium processing facility: Successes and progress at technical area (TA) -55 of the Los Alamos National Laboratory

    Balkey, J.J.; Robinson, M.A.; Boak, J.

    1997-01-01

    The Los Alamos National Laboratory has ongoing national security missions that necessitate increased plutonium processing. The bulk of this activity occurs at Technical Area -55 (TA-55), the nations only operable plutonium facility. TA-55 has developed and demonstrated a number of technologies that significantly minimize waste generation in plutonium processing (supercritical CO 2 , Mg(OH) 2 precipitation, supercritical H 2 O oxidation, WAND), disposition of excess fissile materials (hydride-dehydride, electrolytic decontamination), disposition of historical waste inventories (salt distillation), and Decontamination ampersand Decommissioning (D ampersand D) of closed nuclear facilities (electrolytic decontamination). Furthermore, TA-55 is in the process of developing additional waste minimization technologies (molten salt oxidation, nitric acid recycle, americium extraction) that will significantly reduce ongoing waste generation rates and allow volume reduction of existing waste streams. Cost savings from reduction in waste volumes to be managed and disposed far exceed development and deployment costs in every case. Waste minimization is also important because it reduces occupational exposure to ionizing radiation, risks of transportation accidents, and transfer of burdens from current nuclear operations to future generations

  17. Effect of radiation on normal hematopoiesis and on viral induced cancers of the hematopoietic system. Three-year technical progress report, August 1, 1973--April 30, 1976

    OKunewick, J.P.

    1976-01-01

    In studies conducted during the first three-year segment of this contract, it was observed that in the process of viral leukemogenesis the affected animals became more radioresistant than normal. Initial studies into the reason for the enhanced radioresistance implicated an increase in the number of pluripotent stem cells as one possible cause. During the current period, studies were carried out to further define the effect of the virus on stem cells and their kinetics using exposure to tritiated thymidine ( 3 HTdR) in vivo and in vitro. In addition, separate studies were initiated in an attempt to determine if the immune system played a part in the radioresistance, as well as what the effects might be of immune manipulations on the disease during the oncogenic period. Finally, studies were also undertaken to assess the sensitivity of the virus itself to radiation in vitro and in vivo to radiation and treatment with cells transplanted from viral resistant mice

  18. Role of non-ferrous coal minerals and by-product metallic wastes in coal liquefaction. Technical progress report, December 1, 1980-February 28, 1981

    Garg, D.; Givens, E.N.; Schweighardt, F.K.; Curtis, C.W.; Guin, J.A.; Huang, W.J.; Shridharani, K.

    1981-04-01

    Results from screening studies showed that the pyrite samples separated from various coal seams had similar catalytic activity. The addition of all the pyrite samples to feed slurry increased conversion of coal and production of oil. A sample of fusinite was also tested for its liquefaction behavior with and without added pyrite. The addition of pyrite increased the conversion of fusinite and production of oil. These results show that pyrite catalyzes the conversion of fusinite and therefore improves overall coal conversion. Conversion of coal and oil production increased by impregnating coal with iron and molybdenum compounds. Coal conversion and oil production also increased with increasing concentration of both iron and molybdenum impregnated on coal. Addition of various transition metal sulfides increased coal conversion and oil production. Dramatic improvements were noted with nickel, vanadium, and tin sulfides. Addition of transition metal naphthenates produced mixed results; some of them improved coal conversion and others had no effect. The effect of metal concentration on coal conversion was also not clear. Deep cleaning of coal did not affect coal conversion, but it significantly reduced oil production. Addition of pyrite separated from coal to deep cleaned coal sample regained the oil production to the original value, i.e., oil produced from liquefaction of raw coal.Coal cleaned by oil agglomeration gave highest coal conversion and oil production. Basic and non-basic nitrogen compounds reduced the naphthalene hydrogenation activity of both Co-Mo-Al and sulfided Fe/sub 2/O/sub 3/. Sulfided Fe/sub 2/O/sub 3/ was inactive for denitrogenation of quinoline, and the reaction product mainly consisted of hydrogenated and hydrocracked quinoline. On the contrary, Co-Mo-Al was active for denitrogenation of quinoline, resulting in lower quinoline poisoning.

  19. Development of coal-based technologies for Department of Defense Facilities. Semiannual technical progress report, September 28, 1996--March 27, 1997

    Miller, B.G.; Miller, S.F.; Pisupati, S.V. [and others

    1997-07-22

    The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Slurry Fuel Technology, with the aim of developing technologies which can potentially decrease DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Work in Phase III focused on coal preparation studies, pilot-scale NO{sub x} reduction studies, economic analyses of coal use, and evaluation of deeply-cleaned coal as boiler fuel. Coal preparation studies were focused on continuing activities on particle size control, physical separations, surface-based separation processes, and dry processing. Preliminary pilot-scale NO{sub x} reduction catalyst tests were conducted when firing natural gas in Penn State`s down-fired combustor. This is the first step in the scale-up of bench-scale results obtained in Phase II to the demonstration boiler scale when firing coal. The economic study focused on community sensitivity to coal usage, regional/national economic impacts of new coal utilization technologies, and constructing a national energy portfolio. The evaluation of deeply-cleaned coal as boiler fuel included installing a ribbon mixer into Penn State`s micronized coal-water mixture circuit for reentraining filter cake. In addition, three cleaned coals were received from CQ Inc. and three cleaned coals were received from Cyprus-Amax.

  20. The development of coal-based technologies for Department of Defense facilities. Semiannual technical progress report, March 28, 1995--September 27, 1995

    Miller, B.G.; Hatcher, P.; Knicker, H. [Pennsylvania State Univ., University Park, PA (United States). Energy and Fuels Research Center] [and others

    1996-10-21

    The U.S. Department of Defense (DOD), through the Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Mixture Technology, with the aim of decreasing DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Activities this reporting period are summarized by phase. During this reporting period, preparation of the Phase I final report continued. Work on Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included initiating a study to identify appropriate SO{sub 2} and NO{sub x} control technologies for coal-fired industrial boilers. In addition, work started on the design of a ceramic filtering device for installation on the demonstration boiler. The ceramic filter device will be used to demonstrate a more compact and efficient filtering device for retrofit applications. Coal preparation and utilization activities, and the economic analysis were completed and work focused on preparing the final report. Work on Phase III focused on coal preparation studies and economic analyses of coal use. Coal preparation studies were focused on continuing activities on particle size control, physical separations, surface-based separation processes, and dry processing. The economic study focused on selecting incentives for commercialization of coal using technologies, community sensitivity to coal usage, regional economic impacts of new coal utilization technologies, and constructing a national energy portfolio.

  1. Chemical development Separations Technology Unit. Progress report

    Woodfield, F.W.

    1952-07-31

    The Redox Plant operated at a 76.7% time efficiency (IAF basis) and averaged 3.16 tons of uranium per operating day during the month. During the period from July 4 through July 13, 38,000 gallons of 72% ANN from Tygon-lined storage tank SS-112 were used in aqueous salt solution make-ups with some emulsion difficulty and fission-product carry-over resulting. New ANN, from stainless-steel tanks, was used for the balance of the month. An extensive (thermally) hot 60% HNO{sub 3} cleanout was given to the IA, IB, 2D, 3D, 2A, and 3A columns and associated salt solution head tanks to prepare the solvent-extraction battery for operation using 90-day `cooled` uranium. Continuous cross-over oxidation to improve 2A Column waste losses, and employment of KOH (vice NaOH) in 2DS, ICU, and 2EU butt additions to minimize Na in 3EU, were begun concurrently on July 20. Aged (90-day) uranium in head-end treated feed batches, was started to the IA Column on July 21, with early data indicating adequate two-cycle decontamination for both uranium and plutonium.

  2. A separator

    Prokopyuk, S.G.; Dyachenko, A.Ye.; Mukhametov, M.N.; Prokopov, O.I.

    1982-01-01

    A separator is proposed which contains separating slanted plates and baffle plates installed at a distance to them at an acute angle to them. To increase the effectiveness of separating a gas and liquid stream and the throughput through reducing the secondary carry away of the liquid drops and to reduce the hydraulic resistance, as well, openings are made in the plates. The horizontal projections of each opening from the lower and upper surfaces of the plate do not overlap each other.

  3. Undergraduate technical skills training guided by student tutors – Analysis of tutors' attitudes, tutees' acceptance and learning progress in an innovative teaching model

    Weyrich, Peter; Schrauth, Markus; Kraus, Bernd; Habermehl, Daniel; Netzhammer, Nicolai; Zipfel, Stephan; Jünger, Jana; Riessen, Reimer; Nikendei, Christoph

    2008-01-01

    Background Skills labs provide a sheltered learning environment. As close supervision and individual feedback were proven to be important in ensuring effective skills training, we implemented a cross-year peer tutor system in our skills lab of internal medicine that allowed intense training sessions with small learning groups (3–4 students) taught by one student tutor. Methods The expectations, experiences and criticisms of peer tutors regarding the tutor system for undergraduate skills lab training were investigated in the context of a focus group. In addition, tutees' acceptance of this learning model and of their student tutors was evaluated by means of a pre/post web-based survey. Results 14 voluntary senior students were intensely prepared by consultants for their peer tutor activity. 127 students participated in the project, 66.9% of which responded to the web-based survey (23 topics with help of 6-point Likert scale + free comments). Acceptance was very high (5.69 ± 0.07, mean ± SEM), and self-confidence ratings increased significantly after the intervention for each of the trained skills (average 1.96 ± 0.08, all p skills training to be provided by faculty staff only. Focus group analyses with tutors revealed 18 different topics, including profit in personal knowledge and personal satisfaction through teaching activities. The ratio of 1:4 tutor/tutees was regarded to be very beneficial for effective feedback, and the personalized online evaluation by tutees to be a strong motivator and helpful for further improvements. The tutors ascribed great importance to the continuous availability of a contact doctor in case of uncertainties. Conclusion This study demonstrates that peer teaching in undergraduate technical clinical skills training is feasible and widely accepted among tutees, provided that the tutors receive sufficient training and supervision. PMID:18400106

  4. Computational modeling and experimental studies on NO{sub x} reduction under pulverized coal combustion conditions. Third quarterly technical progress report, July 1, 1995--September 30, 1995

    Kumpaty, S.K.; Subramanian, K.

    1995-12-31

    An experimental plan outlining the first year`s activity was sent to Dr. Lori Gould, Project Officer/Contracting Officer`s Technical Representative on April 24, 1995. An approval was received with some questions on June 15, 1995. However, with some foresight of the director of the in-house combustion group of the PETC, Dr. Ekmann, a tentative hold-off on the purchase of the equipment was requested by the project officer on June 29, 1995. Enclosed with that request were some of Dr. Ekmann`s concerns. The research team spent the month of July in study of pertinent literature as well as in the preparation of the responses to Dr. Gould`s comments and Dr. Ekmann`s concerns. These responses included the choice of the reactor, reactor design, rate of gas heating, detailed test matrix and answers to host of other comments. Upon review of the above information submitted on July 24, 1995 by the Rust research team, the project officer called for a conference call on September 6, 1995 which involved the PI (Dr. Kumpaty), the research consultant (Mr. Subramanian), Dr. Gould and Dr. Ekmann. Dr. Ekmann insisted that further calculations be made on the rate of gas heating without taking radiation into account. Accordingly, calculations pertaining to the rate of gas heating based on convection were performed and submitted to Dr. Ekmann on September 13, 1995. This report contains the information emerged through the dialogue between the Rust College research team and the PETC represented by Dr. Gould and Dr. Ekmann during this quarter.

  5. Modeling of cladding and fuel motion in a loss of flow situation for GCFR safety analysis. Technical progress report (annual), June 15, 1974--March 15, 1975

    Eggen, D.T.

    1975-01-01

    During the first nine months of the project, methods and apparatus were developed to study the freezeout of molten cladding in a cooler blanket region. Three tests were run in which a mass of molten material from a simulated core region of a GCFR flowed into a bundle of simulated blanket elements. In all cases plugging occurred in or before the first grid-spacer. Theories and preliminary models are in accord with these observations. These tests have been done with a 50/50-Pb/Sn alloy simulating the cladding and spacer grids and alumina simulating the fuel. Materials are being obtained for tests with stainless steel cladding and spacers. Development is progressing well on an electrically-heated fuel element which will be used to study the melting and motion of cladding in the core region for a loss of flow accident. Preliminary models is being developed to calculate the motion and freezeout of flowing cladding in the blanket region. The SAS-GAS and Argus codes are being adapted for uses in conjunction with model development on the project. A survey of fission gas effects in oxide during TOP cases was prepared and other codes (LIFE) were reviewed for possible value on the project. A set of reference physical parameters is being developed for the various materials used in the analysis and experiments. (U.S.)

  6. Development of innovative techniques and principles that may be used as models to improve plant performance. Technical progress report, February 1, 1990--January 31, 1993

    Hanna, W.W.; Burton, G.W.

    1992-06-01

    Methods and techniques for transferring germplasm from wild to cultivated species are being developed. The transferred germplasm is being shown to be valuable in plant breeding and in cultivar development. In the primary gene pool of the grassy Pennisetum glaucum subspecies monodii germplasm, some cytoplasms are being identified that appear to have significant effects on forage yields and morphological characteristics. One cytoplasm, A{sub 4}, is very stable for male sterility and fertility is not easily restored by other lines. It should be a valuable cytoplasm for producing commercial forage hybrids. Disease resistance and yield genes transferred from monodii to cultivated pearl millet lines are having a major impact on increasing production of animals grazing disease resistant Tifleaf 2 pearl millet. Genes controlling resistance to many of the world-wide diseases on pearl millet are being identified in the monodii germplasm. Valuable germplasm has been transferred from the secondary gene pool P. purpuroum) which is used as the pollinator of the first pearl millet grain hybrid in the US Production of 7-chromosome gametes in 42-chromosome interspecific hybrids appears to be genotype specific and makes possible transfer of germplasm from the secondary gene pool to cultivated diploid pearl millet. Significant progress has been made in transferring genes controlling apomixis from P. squamulatum (tertiary gene pool) to cultivated pearl millet. Highly apomictic BC{sub 4} plants have been recovered, one of which sets five times as much seed as the best BC{sub 3} plant.

  7. CROSSCUTTING TECHNOLOGY DEVELOPMENT AT THE CENTER FOR ADVANCED SEPARATION TECHNOLOGIES

    Hugh W. Rimmer

    2004-05-12

    This Technical Progress Report describes progress made on the seventeen subprojects awarded in the first year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices. Due to the time taken up by the solicitation/selection process, these cover the initial 6-month period of project activity only. The U.S. is the largest producer of mining products in the world. In 1999, U.S. mining operations produced $66.7 billion worth of raw materials that contributed a total of $533 billion to the nation's wealth. Despite these contributions, the mining industry has not been well supported with research and development funds as compared to mining industries in other countries. To overcome this problem, the Center for Advanced Separation Technologies (CAST) was established to develop technologies that can be used by the U.S. mining industry to create new products, reduce production costs, and meet environmental regulations. Originally set up by Virginia Tech and West Virginia University, this endeavor has been expanded into a seven-university consortium--Virginia Tech, West Virginia University, University of Kentucky, University of Utah, Montana Tech, New Mexico Tech and University of Nevada, Reno--that is supported through U.S. DOE Cooperative Agreement No. DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. Much of the research to be conducted with Cooperative Agreement funds will be longer-term, high-risk, basic research and will be carried out in five broad areas: (1) Solid-solid separation (2) Solid-liquid separation (3) Chemical/Biological Extraction (4) Modeling and Control, and (5) Environmental Control.

  8. Isotope separation

    Eerkens, J.W.

    1979-01-01

    A method of isotope separation is described which involves the use of a laser photon beam to selectively induce energy level transitions of an isotope molecule containing the isotope to be separated. The use of the technique for 235 U enrichment is demonstrated. (UK)

  9. Quarterly technical progress report on water reactor safety programs sponsored by the Nuclear Regulatory Commission's Division of Reactor Safety Research, January--March 1976

    Zane, J. O.; Farman, R. F.; Hanson, D. J.; Peterson, A. C.; Ybarrondo, L. J.; Berta, V. T.; Naff, S. A.; Crocker, J. G.; Martinson, Z. R.; Smolik, G. R.; Cawood, G. W.; Quapp, W. J.; Ramsthaler, J. H.; Ransom, V. H.; Scofield, M. P.; Dearien, J. A.; Bohn, M. P.; Burnham, B. W.; James, S. W.; Lee, W. H.; Lime, J. F.; Nalezny, C. L.; MacDonald, P. E.; Thompson, L. B.; Domenico, W. F.; Rice, R. E.; Hendrix, C. E.; Davis, C. B.

    1976-06-01

    Light water reactor sfaety research performed January through March 1976 is summarized. Results of the Semiscale Mod-1 blowdown heat transfer test series relating to those phenomena that influence core fluid and heat transfer effects are analyzed, and preliminary analyses of the recently completed reflood heat transfer test series are summarized for the forced and gravity feed reflood tests. The first nonnuclear LOCE in the LOFT program was successfully completed and preliminary results are presented. Preliminary results are given for the PCM 8-1 RF Test, the PCM-2A Test, and the Irradiation Effects Scoping Test 2 in the Thermal Fuel Behavior Program. Model development and verification efforts reported in the Reactor Behavior Program include checkout of RELAP4/MOD5 Update 1, development of a new hydrodynamic model for two-phase separated flows, development of the RACHET code to assess the assumptions in current fuel behavior codes of uniform stress and strain in the cladding, modifications of the containment code BEACON, analysis of results from the Halden Assembly IFA-429 helium sorption experiment, development of correlations for the thermal conductivity of UO/sub 2/ and (U,Pu)O/sub 2/, and evaluation of RALAP4 through comparison of calculated results with data from the GE Blowdown Heat Transfer and Semiscale experiments.

  10. Technical writing versus technical writing

    Dillingham, J. W.

    1981-01-01

    Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

  11. Investigation of sulfur-tolerant catalysts for selective synthesis of hydrocarbon liquids from coal-derived gases. Annual technical progress report, September 19, 1980-September 18, 1981

    Bartholomew, C.H.

    1981-10-31

    During the past contract year, considerable progress was made in characterization and activity/selectivity testing of iron and cobalt catalysts. Preparation of boride promoted cobalt and iron catalysts was refined and nearly completed. H/sub 2/ and CO adsorption and oxygen titration measurements were performed on a number of supported and unsupported catalysts, especially several boride promoted cobalt and iron catalysts. Activity/selectivity tests of 3 and 15% Fe/SiO/sub 2/ and Co/SiO/sub 2/ and of 6 borided cobalt and iron catalysts were completed. The product distributions for iron and cobalt boride catalysts are unusual and interesting. Boron promoted iron is more active and stable than iron/silica; cobalt boride has an unusually high selectivity for alcohols. Tests to determine effects of H/sub 2/S poisoning on activity/selectivity properties of 15% Co/SiO/sub 2/ indicate that a significant loss of activity occurs over a period of 24 to 28 h in the presence of 10 to 20 ppM H/sub 2/S. Product selectivity to liquids increased through a maximum during the gradual addition of sulfur. Reactant CO and H/sub 2/S interact partially to form COS which is less toxic than H/sub 2/S. H/sub 2/ and CO adsorption data were obtained for 3, 6 and 9% Co/ZSM-5 catalysts prepared and reactor tested by PETC. The unusual and interesting results suggest that metal-support interactions may have an important influence on reactant adsorption properties.

  12. A Novel Rrm3 Function in Restricting DNA Replication via an Orc5-Binding Domain Is Genetically Separable from Rrm3 Function as an ATPase/Helicase in Facilitating Fork Progression

    Syed, Salahuddin; Desler, Claus; Rasmussen, Lene J.; Schmidt, Kristina H.

    2016-01-01

    In response to replication stress cells activate the intra-S checkpoint, induce DNA repair pathways, increase nucleotide levels, and inhibit origin firing. Here, we report that Rrm3 associates with a subset of replication origins and controls DNA synthesis during replication stress. The N-terminal domain required for control of DNA synthesis maps to residues 186–212 that are also critical for binding Orc5 of the origin recognition complex. Deletion of this domain is lethal to cells lacking the replication checkpoint mediator Mrc1 and leads to mutations upon exposure to the replication stressor hydroxyurea. This novel Rrm3 function is independent of its established role as an ATPase/helicase in facilitating replication fork progression through polymerase blocking obstacles. Using quantitative mass spectrometry and genetic analyses, we find that the homologous recombination factor Rdh54 and Rad5-dependent error-free DNA damage bypass act as independent mechanisms on DNA lesions that arise when Rrm3 catalytic activity is disrupted whereas these mechanisms are dispensable for DNA damage tolerance when the replication function is disrupted, indicating that the DNA lesions generated by the loss of each Rrm3 function are distinct. Although both lesion types activate the DNA-damage checkpoint, we find that the resultant increase in nucleotide levels is not sufficient for continued DNA synthesis under replication stress. Together, our findings suggest a role of Rrm3, via its Orc5-binding domain, in restricting DNA synthesis that is genetically and physically separable from its established catalytic role in facilitating fork progression through replication blocks. PMID:27923055

  13. A Novel Rrm3 Function in Restricting DNA Replication via an Orc5-Binding Domain Is Genetically Separable from Rrm3 Function as an ATPase/Helicase in Facilitating Fork Progression.

    Syed, Salahuddin; Desler, Claus; Rasmussen, Lene J; Schmidt, Kristina H

    2016-12-01

    In response to replication stress cells activate the intra-S checkpoint, induce DNA repair pathways, increase nucleotide levels, and inhibit origin firing. Here, we report that Rrm3 associates with a subset of replication origins and controls DNA synthesis during replication stress. The N-terminal domain required for control of DNA synthesis maps to residues 186-212 that are also critical for binding Orc5 of the origin recognition complex. Deletion of this domain is lethal to cells lacking the replication checkpoint mediator Mrc1 and leads to mutations upon exposure to the replication stressor hydroxyurea. This novel Rrm3 function is independent of its established role as an ATPase/helicase in facilitating replication fork progression through polymerase blocking obstacles. Using quantitative mass spectrometry and genetic analyses, we find that the homologous recombination factor Rdh54 and Rad5-dependent error-free DNA damage bypass act as independent mechanisms on DNA lesions that arise when Rrm3 catalytic activity is disrupted whereas these mechanisms are dispensable for DNA damage tolerance when the replication function is disrupted, indicating that the DNA lesions generated by the loss of each Rrm3 function are distinct. Although both lesion types activate the DNA-damage checkpoint, we find that the resultant increase in nucleotide levels is not sufficient for continued DNA synthesis under replication stress. Together, our findings suggest a role of Rrm3, via its Orc5-binding domain, in restricting DNA synthesis that is genetically and physically separable from its established catalytic role in facilitating fork progression through replication blocks.

  14. The economical production of alcohol fuels from coal-derived synthesis gas. Quarterly technical progress report No. 4, July 1, 1992--September 30, 1992

    1993-10-01

    A base case flow sheet for the production of higher alcohols from coal derived synthesis gas has been completed, including an economic analysis. The details of the flow sheet and economics are in Appendix 1. The pay back period for the capital investment for the plant has been calculated as a function of the market price of the product, and this figure is also shown as Figure I in Appendix 1. The estimated installed cost is almost $500 MM, and the estimated annual operating cost is $64 MM. At a price in the vicinity of $1.00/gal for the alcohol product, the pay back period for construction of the plant is four years. These values should be considered preliminary, since many of the capital costs were obtained from other paper studies sponsored by DOE and TVA and very few values could be found from actual plants which were built. This issue is currently being addressed. The most expensive capital costs were found to be the gasifier, the cryogenic air separation plant, the steam/power generation plant and the acid gas/sulfur removal processes taken as a whole. It is planned to focus attention on alternatives to the base case. The problem is that it is less expensive to make syngas from natural gas. Therefore, it is essential to reduce the cost of syngas from coal. This is where the energy park concept becomes important. In order for this process to be economical (at current market and political conditions) a method must be found to reduce the cost of syngas manufacture either by producing energy or by-products. Energy is produced in the base case, but the amount and method has not been optimized. The economic arguments for this concept are detailed in Appendix 2.

  15. Final Technical Report

    John Ross

    2003-04-30

    The Final Technical Report summarizes research accomplishments and Publications in the period of 5/1/99 to 4/30/03 done on the grant. Extensive progress was made in the period covered by this report in the areas of chemical kinetics of non-linear systems; spatial structures, reaction - diffusion systems, and thermodynamic and stochastic theory of electrochemical and general systems.

  16. Design, Synthesis, and Mechanistic Evaluation of Iron-Based Catalysis for Synthesis Gas Conversion to Fuels and Chemicals. Technical Progress Report

    Akio Ishikawa; Manuel Ojeda; Nan Yao; Enrique Iglesia

    2006-01-01

    area promoter. The kinetic behavior of these materials, specifically the effects of H 2 , CO, and CO 2 on the rates and selectivities of Fischer-Tropsch synthesis reactions has led to a new proposal for the nature of rate-determining steps on Fe and Co Fischer-Tropsch catalysts, and more specifically to the roles of hydrogen-assisted and alkali-assisted dissociation of CO in determining rates and CO 2 selectivities. Finally, we have started an exploratory study of the use of colloidal precipitation methods for the synthesis of small Fe and Co clusters using recently developed methods. During this period, we have had to restrict manpower assigned to this project because some irregularities in reporting and communications have led to the interruption of funding during this period. This has led to less than optimal productivity and to significant disruptions of the technical work. These issues have also led to significant underspending of project funds during this reporting period and to our consequent request for a no-cost extension of one year, which we understand has been granted

  17. Experimental investigation of the chemistry of excited states of rare gases. Annual technical progress report, October 15, 1976--October 14, 1977

    Setser, D.W.

    1978-01-01

    Tunable dye laser fluorescence has been combined with the flowing afterglow technique as a method for studying reactive intermediates present in the flowing afterglow. The radiative lifetimes and two-body quenching rate constants (with Ar carrier gas) for the Ar*(3p 5 ,4p) and Ar*(3p 5 ,5p) excited states were reported in the preceding year. During this year, we have measured the Ar* product states from the two-body quenching. More than 50% of the quenching leads directly to intermultiplet transfer to Ar(4s) states, rather than to intramultiplet cascade down the Ar(4p) manifold. Using this technique we also have studied the Xe(5p 5 ,6p') and Xe(5p 5 ,7p) excited states and radiative lifetimes, two-body quenching and the product states from quenching have been ascertained. These data should be of value for modeling energy flow pathways of rare gases excited by high energy electrons. A method has been developed for studying the quenching of the XeF(B) and KrF(B) by a variety of reagent molecules. A preliminary account of this work was published (number 5 in the publication list). Much additional experimental work has been done and a definitive study of the electronic quenching of XeF(B) and KrF(B) is in progress. Efforts to interpret (and publish) our comprehensive studies of the reactive quenching of the Kr( 3 P 2 ) and Xe( 3 P 2 ) by fluorine and chlorine-containing molecules has continued (see numbers 4, 6 and 8 in the publication listing). Two more manuscripts are in final stages of preparation. Of particular importance has been the development of methods for simulating and interpreting the bound-free emission spectra from the very high vibrational levels of the xenon and krypton fluorides and chlorides. Experiments have been done to measure the branching ratios for (i) ArF* formation from reactive quenching of Ar( 3 P 2 ) with fluorine-containing reagents and (ii) KrBr* and Br* formation for Kr( 3 P 2 ) reacting with some bromine-containing molecules

  18. CENTRIFUGAL SEPARATORS

    Skarstrom, C.

    1959-03-10

    A centrifugal separator is described for separating gaseous mixtures where the temperature gradients both longitudinally and radially of the centrifuge may be controlled effectively to produce a maximum separation of the process gases flowing through. Tbe invention provides for the balancing of increases and decreases in temperature in various zones of the centrifuge chamber as the result of compression and expansions respectively, of process gases and may be employed effectively both to neutralize harmful temperature gradients and to utilize beneficial temperaturc gradients within the centrifuge.

  19. Microparticle Separation by Cyclonic Separation

    Karback, Keegan; Leith, Alexander

    2017-11-01

    The ability to separate particles based on their size has wide ranging applications from the industrial to the medical. Currently, cyclonic separators are primarily used in agriculture and manufacturing to syphon out contaminates or products from an air supply. This has led us to believe that cyclonic separation has more applications than the agricultural and industrial. Using the OpenFoam computational package, we were able to determine the flow parameters of a vortex in a cyclonic separator in order to segregate dust particles to a cutoff size of tens of nanometers. To test the model, we constructed an experiment to separate a test dust of various sized particles. We filled a chamber with Arizona test dust and utilized an acoustic suspension technique to segregate particles finer than a coarse cutoff size and introduce them into the cyclonic separation apparatus where they were further separated via a vortex following our computational model. The size of the particles separated from this experiment will be used to further refine our model. Metropolitan State University of Denver, Colorado University of Denver, Dr. Randall Tagg, Dr. Richard Krantz.

  20. Isotopic separation

    Castle, P.M.

    1979-01-01

    This invention relates to molecular and atomic isotope separation and is particularly applicable to the separation of 235 U from other uranium isotopes including 238 U. In the method described a desired isotope is separated mechanically from an atomic or molecular beam formed from an isotope mixture utilising the isotropic recoil momenta resulting from selective excitation of the desired isotope species by radiation, followed by ionization or dissociation by radiation or electron attachment. By forming a matrix of UF 6 molecules in HBr molecules so as to collapse the V 3 vibrational mode of the UF 6 molecule the 235 UF 6 molecules are selectively excited to promote reduction of UF 6 molecules containing 235 U and facilitate separation. (UK)

  1. Isotopic separation

    Chen, C.L.

    1979-01-01

    Isotopic species in an isotopic mixture including a first species having a first isotope and a second species having a second isotope are separated by selectively exciting the first species in preference to the second species and then reacting the selectively excited first species with an additional preselected radiation, an electron or another chemical species so as to form a product having a mass different from the original species and separating the product from the balance of the mixture in a centrifugal separating device such as centrifuge or aerodynamic nozzle. In the centrifuge the isotopic mixture is passed into a rotor where it is irradiated through a window. Heavier and lighter components can be withdrawn. The irradiated mixture experiences a large centrifugal force and is separated in a deflection area into lighter and heavier components. (UK)

  2. Isotopic separation

    Chen, C.L.

    1982-01-01

    A method is described for separating isotopes in which photo-excitation of selected isotope species is used together with the reaction of the excited species with postive ions of predetermined ionization energy, other excited species, or free electrons to produce ions or ion fragments of the selected species. Ions and electrons are produced by an electrical discharge, and separation is achieved through radial ambipolar diffusion, electrostatic techniques, or magnetohydrodynamic methods

  3. ISABELLE: a progress report

    Hahn, H

    1980-01-01

    This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed.

  4. ISABELLE: a progress report

    Hahn, H.

    1980-01-01

    This paper discusses the ISABELLE project, which has the objective of constructing a high-energy proton colliding beam facility at Brookhaven National Laboratory. The major technical features of the intersecting storage accelerators with their projected performance are described. Application of over 1000 superconducting magnets in the two rings represents the salient characteristic of the machine. The status of the entire project, the technical progress made so far, and difficulties encountered are reviewed

  5. Separation system

    Rubin, L.S.

    1986-01-01

    A disposal container is described for use in disposal of radioactive waste materials consisting of: top wall structure, bottom wall structure, and circumferential side wall structure interconnecting the top and bottom wall structures to define an enclosed container, separation structure in the container adjacent the inner surface of the side wall structure for allowing passage of liquid and retention of solids, inlet port structure in the top wall structure, discharge port structure at the periphery of the container in communication with the outer surface of the separation structure for receiving liquid that passes through the separation structure, first centrifugally actuated valve structure having a normal position closing the inlet port structure and a centrifugally actuated position opening the inlet port structure, second centrifugally actuated valve structure having a normal position closing the discharge port structure and a centrifugally actuated position opening the discharge port structure, and coupling structure integral with wall structure of the container for releasable engagement with centrifugal drive structure

  6. Separable algebras

    Ford, Timothy J

    2017-01-01

    This book presents a comprehensive introduction to the theory of separable algebras over commutative rings. After a thorough introduction to the general theory, the fundamental roles played by separable algebras are explored. For example, Azumaya algebras, the henselization of local rings, and Galois theory are rigorously introduced and treated. Interwoven throughout these applications is the important notion of étale algebras. Essential connections are drawn between the theory of separable algebras and Morita theory, the theory of faithfully flat descent, cohomology, derivations, differentials, reflexive lattices, maximal orders, and class groups. The text is accessible to graduate students who have finished a first course in algebra, and it includes necessary foundational material, useful exercises, and many nontrivial examples.

  7. Isotope separation

    Bartlett, R.J.; Morrey, J.R.

    1978-01-01

    A method and apparatus is described for separating gas molecules containing one isotope of an element from gas molecules containing other isotopes of the same element in which all of the molecules of the gas are at the same electronic state in their ground state. Gas molecules in a gas stream containing one of the isotopes are selectively excited to a different electronic state while leaving the other gas molecules in their original ground state. Gas molecules containing one of the isotopes are then deflected from the other gas molecules in the stream and thus physically separated

  8. The improvement of near-term CdTe processing and product capabilities and establishment of next-generation CdTe technology. Annual technical progress report, September 1, 1995--August 31, 1996

    Kester, J.; Albright, S. [Golden Photon, Inc., CO (United States)

    1997-07-01

    The potential of photovoltaics to become a major global business enterprise still lingers outside the limits of industrial capabilities. For the Cadmium Sulfide/Cadmium Telluride (CdS/CdTe) system this potential has continued to focus on improvements in efficiency, stability, and cost reduction. This triad is the primary objective of the present subcontract with NREL entitled {open_quotes}The Improvement of Near-term CdTe Processing and Product Capabilities & Establishment of Next Generation CdTe Technology{close_quotes}. This subcontract represents an intermediate stage of NREL`s plan to assist the growth of the photovoltaic industry in overcoming the scientific and technical barriers to commercialization. This report outlines the progress that has been made during the period of August 1995 through August 1996. The objectives of this subcontract are to improve processing methods, quantify and understand efficiency improvement mechanisms, meet life-testing goals, and address cadmium safety concerns. Task and subtask goals are defined to meet these objectives in specific areas. The approach to fulfilling the subcontract goals is through a balanced plan of process improvement and mechanism identification. These are carried out and continued through monitoring under various long term and accelerated stress conditions. GPI maintains an on-going awareness of all safety related issues, can in particular, those involving cadmium.

  9. US/Japan collaborative program on fusion reactor materials: Summary of the tenth DOE/JAERI Annex I technical progress meeting on neutron irradiation effects in first wall and blanket structural materials

    Rowcliffe, A.F.

    1989-01-01

    This meeting was held at Oak Ridge National Laboratory on March 17, 1989, to review the technical progress on the collaborative DOE/JAERI program on fusion reactor materials. The purpose of the program is to determine the effects of neutron irradiation on the mechanical behavior and dimensional stability of US and Japanese austenitic stainless steels. Phase I of the program focused on the effects of high concentrations of helium on the tensile, fatigue, and swelling properties of both US and Japanese alloys. In Phase II of the program, spectral and isotropic tailoring techniques are fully utilized to reproduce the helium:dpa ratio typical of the fusion environment. The Phase II program hinges on a restart of the High Flux Isotope Reactor by mid-1989. Eight target position capsules and two RB* position capsules have been assembled. The target capsule experiments will address issues relating to the performance of austenitic steels at high damage levels including an assessment of the performance of a variety of weld materials. The RB* capsules will provide a unique and important set of data on the behavior of austenitic steels irradiated under conditions which reproduce the damage rate, dose, temperature, and helium generation rate expected in the first wall and blanket structure of the International Thermonuclear Experimental Reactor

  10. Nuclear Physics Laboratory technical progress report

    1991-01-01

    This contract supports broadly based experimental work in intermediate energy nuclear physics. The program includes pion- nucleon studies at TRIUMF and LAMPF, inelastic pion scattering and charge exchange reactions at LAMPF, and nucleon charge exchange at LAMPF/NTOF. The first results of spin-transfer observables in the isovector (rvec p,rvec n) reaction are included in this report. Our data confirm the tentative result from (rvec p,rvec p) reactions that the nuclear isovector spin response shows neither longitudinal enhancement nor transverse quenching. Our program in quasifree scattering of high energy pions shows solid evidence of isoscalar enhancement of the nuclear nonspin response. We include several comparisons of the quasifree scattering of different probes. Results from our efforts in the design of accelerator RF cavities are also included in this report

  11. Technical progress - a chance for the future

    Schubert, J

    1981-12-01

    The insufficient acceptance of technology in the society of today has its roots in the past century when a humanistically oriented education system had superseded the practice-oriented way. The emotional refusal of science and technology resulting herefrom caused some difficulties when new technologies, as e.g. microelectronics, were introduced. As microelectronics is rated as a basic innovation it entails social and economic changes.

  12. MRS feasibility assessment grant technical progress report

    1993-01-01

    On January 13, 1993, Governor of the State of Utah, Mike Leavitt officially announced that he was opposing a MRS Facility in the State of Utah and informed San Juan County of his decision which will preclude the County from applying for a Phase IIa feasibility grant. A copy of the policy statement made by Governor Leavitt is included in this report. Additionally, a bill in the State House of Representative has been filed opposing the facility. A copy of the bill is also included. The work accomplished under Phase I, indicated that there was about an equal amount of residents in San Juan County opposed and in favor of the facility. There were many concerns and issues presented during the Phase I grant period that would have been continued to Phase IIa, if allowed, including the citizen committee

  13. Regional cooperation to stimulate technical progress

    Ridvan, M.; Ehjrej, P.L.

    1987-01-01

    The main principles of the IAEA regional agreement on co-operation in the field of researches, elaboration and training of specialists in nuclear science and engineering for the states of Asia and Pacific Ocean region (RAC) and of the ARCAL program in Latin America are considered. The RAC projects envisage co-operation in the field of medicine (radiotherapy and nuclear methods, sterilization, etc.), agriculture (nuclear methods, raising of plants, using radiation mutations, food irradiation, etc.), industry (application of isotopes and radiation technology) and others. The ARCAL projects comprise radiation protection, nuclear control instruments, nuclear analytic methods, radioimmune analysis in stock-breeding, product irradiation, nuclear information, etc

  14. Technical progress in nuclear medical heart diagnosis

    Standke, R.; Hoer, G.

    1989-01-01

    The rapid development in nuclear cardiology worldwide can hardly be surveyed from the point of view of one center. In connection with the general nuclear cardiologic development this study describes a multiparameter analysis of regional left ventricular function during exercise, and the method of sectoranalysis for quantification of myocardial SPECT. Finally a one-step procedure to quantify left ventricular function and myocardial perfusion is presented. (orig.) [de

  15. Quarterly Technical Progress Report June 2015

    Buchholz, Bruce A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-06-08

    The project has two main goals: 1) Identify the types of adducts naphthalene (NA) forms with DNA and 2) determine whether adduct formation correlates with site selective tumor formation in defined subcompartments of the respiratory tract (respiratory and olfactory nasal epithelium and airways of mice, rats and rhesus monkeys). Five tasks are associated with the completion of the goals. Task 1: Contracting and Animal Use Approvals. IACUC and ACURO approvals are complete, The subcontract with UC Davis (UCD) was executed in December 2014. Task 2: Perform In Vitro Study for Goal 1. Rat samples exposed and in freezer while adduct standards are being made. Mouse samples need to be exposed in next quarter. Task 3: Perform In Vitro Study for Goal 2. Mouse ex vivo samples completed. Rat and monkey samples need to be completed in the next quarter. Task 4: Sample Preparation and Analysis. Mouse Goal 2 samples completed. Other samples remain to be done. Task 5: Data Interpretation and Reporting. Need rat data to write paper on adduct formation.

  16. Operational Group Sandy technical progress report

    ,

    2013-01-01

    Hurricane Sandy made US landfall near Atlantic City, NJ on 29 October 2012, causing 72 direct deaths, displacing thousands of individuals from damaged or destroyed dwellings, and leaving over 8.5 million homes without power across the northeast and mid-Atlantic. To coordinate federal rebuilding activities in the affected region, the President established the cabinet-level Hurricane Sandy Rebuilding Task Force (Task Force). The Task Force was charged with identifying opportunities for achieving rebuilding success while supporting economic vitality, improving public health and safety, protecting and enhancing natural and manmade infrastructure, bolstering resilience, and ensuring appropriate accountability.

  17. Imagining Technicities

    Liboriussen, Bjarke; Plesner, Ursula

    2011-01-01

    to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

  18. Progress report 1979

    1980-12-01

    This progress report deals with technical and research work done at the AAEC Research Establishment in the twelve month period ending September 30, 1979. Work done in the following research divisions is reported: Applied Maths and Computing, Chemical Technology, Engineering Research, Environmental Science, Instrumentation and Control, Isotope, Materials and Physics

  19. Separation technology 2005; Separasjonsteknologi 2005

    NONE

    2005-07-01

    The conference comprises 13 presentations on the topics of separation technology aspects with emphasis on technology assessment. Some topics of particular interest are emulsion stabilization, sand technology and handling, water handling and reservoir injection, technical equipment and compression and pressure aspects.

  20. Gas separating

    Gollan, A.

    1988-03-29

    Feed gas is directed tangentially along the non-skin surface of gas separation membrane modules comprising a cylindrical bundle of parallel contiguous hollow fibers supported to allow feed gas to flow from an inlet at one end of a cylindrical housing through the bores of the bundled fibers to an outlet at the other end while a component of the feed gas permeates through the fibers, each having the skin side on the outside, through a permeate outlet in the cylindrical casing. 3 figs.

  1. Isotope separation

    Rosevear, A.; Sims, H.E.

    1985-01-01

    sup(195m)Au for medical usage is separated from sup(195m)Hg in a solution containing ions of sup(195m)Hg by contacting the solution with an adsorbing agent to adsorb 195 Hgsup(H) thereon, followed by selective elution of sup(195m)Au generated by radioactive decay of the sup(195m)Hg. The adsorbing agent comprises a composite material in the form of an inert porous inorganic substrate (e.g. Kieselguhr),the pores of which are occupied by a hydrogel of a polysaccharide (e.g. agarose) carrying terminal thiol groups for binding Hgsup(H) ions. (author)

  2. Advanced light source: Compendium of user abstracts and technical reports,1993-1996

    None, None

    1997-04-01

    This compendium contains abstracts written by users summarizing research completed or in progress from 1993-1996, ALS technical reports describing ongoing efforts related to improvement in machine operations and research and development projects, and information on ALS beamlines planned through 1998. Two tables of contents organize the user abstracts by beamline and by area of research, and an author index makes abstracts accessible by author and by principal investigator. Technical details for each beamline including whom to contact for additional information can be found in the beamline information section. Separate abstracts have been indexed into the database for contributions to this compendium.

  3. Final Technical Report

    Aristos Aristidou Natureworks); Robert Kean (NatureWorks); Tom Schechinger (IronHorse Farms, Mat); Stuart Birrell (Iowa State); Jill Euken (Wallace Foundation & Iowa State)

    2007-10-01

    The two main objectives of this project were: 1) to develop and test technologies to harvest, transport, store, and separate corn stover to supply a clean raw material to the bioproducts industry, and 2) engineer fermentation systems to meet performance targets for lactic acid and ethanol manufacturers. Significant progress was made in testing methods to harvest corn stover in a “single pass” harvest mode (collect corn grain and stover at the same time). This is technically feasible on small scale, but additional equipment refinements will be needed to facilitate cost effective harvest on a larger scale. Transportation models were developed, which indicate that at a corn stover yield of 2.8 tons/acre and purchase price of $35/ton stover, it would be unprofitable to transport stover more than about 25 miles; thus suggesting the development of many regional collection centers. Therefore, collection centers should be located within about 30 miles of the farm, to keep transportation costs to an acceptable level. These collection centers could then potentially do some preprocessing (to fractionate or increase bulk density) and/or ship the biomass by rail or barge to the final customers. Wet storage of stover via ensilage was tested, but no clear economic advantages were evident. Wet storage eliminates fire risk, but increases the complexity of component separation and may result in a small loss of carbohydrate content (fermentation potential). A study of possible supplier-producer relationships, concluded that a “quasi-vertical” integration model would be best suited for new bioproducts industries based on stover. In this model, the relationship would involve a multiyear supply contract (processor with purchase guarantees, producer group with supply guarantees). Price will likely be fixed or calculated based on some formula (possibly a cost plus). Initial quality requirements will be specified (but subject to refinement).Producers would invest in harvest

  4. Periodic progress report, 6 months

    Juhl, Thomas Winther; Nielsen, Jakob Skov

    This is the first progress report of the BriteEuram project named "High Power Laser Cutting for Heavy Industry" ("Powercut"). The report contains a summary of the objectives of the first period, an overview of the technical progress, a comparison between the planed and the accomplished work...

  5. Technical Network

    2007-01-01

    In order to optimize the management of the Technical Network (TN), to ease the understanding and purpose of devices connected to the TN, and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive email notifications from IT/CS asking them to add the corresponding information in the network database. Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  6. Technical Network

    2007-01-01

    In order to optimise the management of the Technical Network (TN), to facilitate understanding of the purpose of devices connected to the TN and to improve security incident handling, the Technical Network Administrators and the CNIC WG have asked IT/CS to verify the "description" and "tag" fields of devices connected to the TN. Therefore, persons responsible for systems connected to the TN will receive e-mails from IT/CS asking them to add the corresponding information in the network database at "network-cern-ch". Thank you very much for your cooperation. The Technical Network Administrators & the CNIC WG

  7. Electromagnetic separator of plasma

    Gasilin, V.V.; Nezovibatko, Yu.N.; Poklepach, G.S.; Shvets, O.M.; Taran, V.S.; Tereshin, V.I.

    2005-01-01

    The progress in the widespread utilization of the PVD methods is determined in many respects by the plasma quality and, therefore, the necessity of an application of plasma separators, in particular magnetic separators. One needs to note that traditional magnetic separators have a number of problems their using, namely their unwieldiness, the presence of the isolated cameras and so on. We have proposed, manufactured and investigated the simple separator of plasma that doesn't require using additional cameras. As a source of metallic plasma the standard cathode vaporizer in the installation 'BULAT 6' was in use. Plasma stream from the cathode flowed through the not protected by isolation spiral solenoid. The solenoid input (from the cathode side) was under floating potential. The solenoid output was connected to the autonomous power supply system. The solenoid was prepared with stride winding and 90 degree turn. The solenoid current was 20-90 A and the solenoid voltage with respect to the vessel (earth) was +15 V. In this case drifting charged particles could freely fly out from the interior solenoid region to its boundary. The glow of the turned flow of plasma was observed during the supplying of the cathode and the solenoid. Plasma flow was separated from the coils and extended along the axis of solenoid. One can assume that this device ensures radial electric with respect to the bulk of plasma (the diameter of the bulk of plasma is comparable with the cathode diameter), the toroidal magnetic field, produced by solenoid, was of an order of 20 Oe. Magnetic field strength was sufficient for the magnetization of electrons, but it was rather small for magnetizing the ions and charged micro-droplets. The experiments carried out with aluminum cathode on the deposition of coatings at the stainless steel substrate have shown the high effectiveness of this separator operation. Coatings without droplets were obtained also on the glass substrate with HF- displacement

  8. Separation of uranium isotopes

    Ehrfeld, W.; Ehrfeld, U.

    1977-01-01

    In the nuclear fuel cycle, uranium enrichment is not a principal problem of technological feasibility. Several processes exist for producing LWR fuel and the enrichment method can be selected in consideration of economical, environmental, and political aspects. To date, the gaseous diffusion process constitutes the major part of enrichment capacity. This process has been well demonstrated for over 30 years and, as a matter of fact, no major technological and economical progress is to be expected in the future. Because of their comparatively high development potential, the centrifuge and the separation nozzle method may become increasingly favorable in economics. The development of the centrifuge process which is superior by its low specific energy consumption aims at technological improvements. In the separation nozzle process which offers the advantage of a comparatively simple technology a further reduction of the specific energy consumption is to be expected because of the thermodynamically favorable separation mechanism of this process. Laser isotope separation methods are still on the laboratory scale, although large financial funds have been spent. (orig.) [de

  9. Separations chemistry

    Anon.

    1977-01-01

    Infrared spectra of Pu(IV) polymer show effects of CO 2 adsorption and of aging. Uv light (300 nm) increases the rate of reduction of PuO 2 2+ and Pu 4+ to Pu 3+ and the Pu--U separation factor using TBP. Distribution ratios for Zr and Hf between Dowex 50W--X8 resin and H 2 SO 4 solutions were found to decrease sharply with H 2 SO 4 content. Octylphenyl acid phosphate, a mixture of monooctylphenyl and dioctylphenyl phosphoric acids, is being studied for U recovery from wet-process phosphoric acid. A study of HNO 3 leaching of Ra from U ores was completed. Effects of particle size of the packed bed on the dispersion of the boundary of the miscible phase used in oil recovery are being studied. Effects of sulfonates on toluene--n-butanol--water phase relations were determined, as were the effects of salts and solutes on the max water content of 1:1 toluene--alcohol solutions. A study was begun of hydrocarbon solubility in water--surfactant--alcohol. The mechanism of the formation of hydrous ZrO 2 --polyacrylate membranes and their use for sulfate rejection were studied. Salt rejection through hyperfiltration by clay membranes (bentonite and kaolin) was also investigated. Preliminary results are given for hyperfiltration of wood-pulping wastes by ZrO 2 membranes. 13 figures

  10. 48 CFR 2052.211-70 - Preparation of technical reports.

    2010-10-01

    ....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Preparation of technical...

  11. Magnetic separation for soil decontamination

    Avens, L.R.; Worl, L.A.; deAguero, K.J.; Padilla, D.D.; Prenger, F.C.; Stewart, W.F.; Hill, D.D.; Tolt, T.L.

    1993-01-01

    High gradient magnetic separation (HGMS) is a physical separation process that is used to extract magnetic particles from mixtures. The technology is used on a large scale in the kaolin clay industry to whiten or brighten kaolin clay and increase its value. Because all uranium and plutonium compounds are slightly magnetic, HGMS can be used to separate these contaminants from non-magnetic soils. A Cooperative Research and Development Agreement (CRADA) was signed in 1992 between Los Alamos National Laboratory (LANL) and Lockheed Environmental Systems and Technologies Company (LESAT) to develop HGMS for soil decontamination. This paper reports progress and describes the HGMS technology

  12. Storage and separation of gases

    Biloe, S.; Cagnon, B.; Goetz, V.; Guillot, A.; Mauran, S.; Mazet, N.; Menard, D.; Py, X.

    2005-01-01

    Various processes such as gas separation, gas storage (H 2 or CH 4 ) are known to be inhibited by intrinsic antagonistic material properties (texture, thermal conductivity, permeability). In the following document are gathered the last progress in adsorbent material elaboration and process engineering. (authors)

  13. Russian separation program

    Rea, J.L.

    1993-01-01

    A small contract signed in FY92 with the Khlopin Radium Institute marked the beginning of the Russian Separations program. Under this contract the Khlopin Radium Institute performed laboratory and dynamic hot-cell testing using cobalt dicarbollide technology on simulated radioactive wastes similar to those found at DOE sites in the United States. The current scope of investigation has been extended to identify prospective technologies for application to other United States needs. The Khlopin Radium Institute project served as a model for three other pilot scale technology development projects. The premise of the pilot scale projects is to enable Russian scientists to demonstrate their technology in the context of DOE needs, using Russian technical expertise has proven to be a cost-effective means of screening Russian technologies

  14. Fusion reactor materials semiannual progress report for the period ending March 31, 1993

    1993-07-01

    This is the fourteenth in a series of semiannual technical progress reports on fusion reactor materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials programs being conducted in support of the Magnetic Fusion Energy Program of the US Depart of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. Separate abstracts were prepared for each individual section

  15. Fusion reactor materials semiannual progress report for the period ending March 31, 1993

    1993-07-01

    This is the fourteenth in a series of semiannual technical progress reports on fusion reactor materials. These activities are concerned principally with the effects of the neutronic and chemical environment on the properties and performance of reactor materials; together they form one element of the overall materials programs being conducted in support of the Magnetic Fusion Energy Program of the US Depart of Energy. The other major element of the program is concerned with the interactions between reactor materials and the plasma and is reported separately. Separate abstracts were prepared for each individual section.

  16. Technical Note

    Administratör

    In this report on four patients, we did not use any of these techniques. The existence and the site of the fistulas was clearly demonstrated using basic but important preoperative detailed assessment and two intraoperative findings. The preoperative referral note that indicated the site of technical difficulty during the previous ...

  17. TECHNICAL COORDINATION

    A. Ball

    2010-01-01

    Operational Experience At the end of the first full-year running period of LHC, CMS is established as a reliable, robust and mature experiment. In particular common systems and infrastructure faults accounted for <0.6 % CMS downtime during LHC pp physics. Technical operation throughout the entire year was rather smooth, the main faults requiring UXC access being sub-detector power systems and rack-cooling turbines. All such problems were corrected during scheduled technical stops, in the shadow of tunnel access needed by the LHC, or in negotiated accesses or access extensions. Nevertheless, the number of necessary accesses to the UXC averaged more than one per week and the technical stops were inevitably packed with work packages, typically 30 being executed within a few days, placing a high load on the coordination and area management teams. It is an appropriate moment for CMS Technical Coordination to thank all those in many CERN departments and in the Collaboration, who were involved in CMS techni...

  18. TECHNICAL COORDINATION

    A. Ball

    2010-01-01

    Operational Experience Since the closure of the detector in February, the technical operation of CMS has been quite smooth and reliable. Some minor interventions in UXC were required to cure failures of power supplies, fans, readout boards and rack cooling connections, but all these failures were repaired in scheduled technical stops or parasitically during access dedicated to fixing LHC technical problems. The only occasion when CMS had to request an access between fills was to search for the source of an alarm from the leak-detection cables mounted in the DT racks. After a few minutes of diagnostic search, a leaking air-purge was found. Replacement was complete within 2 hours. This incident demonstrated once more the value of these leak detection cables; the system will be further extended (during the end of year technical stop) to cover more racks in UXC and the floor beneath the detector. The magnet has also been operating reliably and reacted correctly to the 14s power cut on 29 May (see below). In or...

  19. Technical endoscopy

    Cavalar, K.O.

    1988-01-01

    A survey is provided on different versions of endoscopes, taking into account the new developments of video endoscopy. With a variety of practical examples it is shown that technical tests using endoscopy are a demanding task for nondestructive testing, whose requirements can only be met on a customized basis. (orig./HP) [de

  20. A Novel Rrm3 Function in Restricting DNA Replication via an Orc5-Binding Domain Is Genetically Separable from Rrm3 Function as an ATPase/Helicase in Facilitating Fork Progression

    Syed, Salahuddin; Madsen, Claus Desler; Rasmussen, Lene J.

    2016-01-01

    hydroxyurea. This novel Rrm3 function is independent of its established role as an ATPase/helicase in facilitating replication fork progression through polymerase blocking obstacles. Using quantitative mass spectrometry and genetic analyses, we find that the homologous recombination factor Rdh54 and Rad5...