Synthesis, characterization, and application of Zn(NH 3)(CO3) for selective adsorptive separation of CO2

Science.gov (United States)

Khazeni, Naasser

This study explores the potential of Zn(NH3)(CO3) for selective CO2 separation. It develops a novel, highly controllable, single-pot synthesis approach based on urea hydrolysis and solvothermal aging to increase the feasibility of synthesizing Zn(NH3)(CO3), determines the structure of Zn(NH3)(CO3) in detail through single crystal X-ray diffraction and powder X-ray diffraction analyses, and performs adsorption analyses for the compound using CO2, N 2, H2, O2, and CH4 as adsorptives. Through adsorptive characterization, a systematic adsorbent selection screening is performed to assess the potential application of Zn(NH3)(CO 3) for adsorptive separation of CO2 from an upstream gas mixture of power generation, hydrogen production, and natural gas industries. Structural analysis shows Zn(NH3)(CO3) to have an inorganic helical framework that consists of a small helix of (ZnOCO) 2 and a large helix of (ZnOCO)4 with two ammines (NH 3) pendant from every other zinc. In terms of adsorption capacity and CO2 selectivity, Zn(NH3)(CO3) adsorbed 0.550 mmole/g CO2 at 293 K and 4500 mmHg, but only 0.047 mmole/g N 2, 0.084 mmole/g H2, 0.207 mmole/g 02, and 0.060 mmole/g CH4 at the same temperature and pressure. This behavior demonstrates considerable equilibrium selectivities - 36, 31, 63, and 11 - for separating CO2 from CH4, CO2 from H 2, CO2 from N2, and CO2 from 02, respectively. During adsorption, the pendant ammines act as the gates of check-valves: applied pressure opens the gates for adsorption; and during desorption, the gates are closed, trapping the adsorbates, until a reduction of pressure to near-atmospheric levels. Therefore, Zn(NH3)(CO3) exhibits low-pressure H3 or H4 hysteresis, indicating that the Zn(NH3)(CO3) framework can achieve gas storage at near-atmospheric pressures. Additionally, the compound proves structurally stable, with an adsorption decrease of 0.8% after 20 adsorption/desorption cycles - a factor that, considered with the other characteristics of Zn

Graphene Oxide Membranes with Heterogeneous Nanodomains for Efficient CO2 Separations.

Science.gov (United States)

Wang, Shaofei; Xie, Yu; He, Guangwei; Xin, Qingping; Zhang, Jinhui; Yang, Leixin; Li, Yifan; Wu, Hong; Zhang, Yuzhong; Guiver, Michael D; Jiang, Zhongyi

2017-11-06

Achieving high membrane performance in terms of gas permeance and carbon dioxide selectivity is an important target in carbon capture. Aiming to manipulate the channel affinity towards CO 2 to implement efficient separations, gas separation membranes containing CO 2 -philic and non-CO 2 -philic nanodomains in the interlayer channels of graphene oxide (GO) were formed by intercalating poly(ethylene glycol) diamines (PEGDA). PEGDA reacts with epoxy groups on the GO surface, constructing CO 2 -philic nanodomains and rendering a high sorption capacity, whereas unreacted GO surfaces give non-CO 2 -philic nanodomains, rendering low-friction diffusion. Owing to the orderly stacking of nanochannels through cross-linking and the heterogeneous nanodomains with moderate CO 2 affinity, a GO-PEGDA500 membrane exhibits a high CO 2 permeance of 175.5 GPU and a CO 2 /CH 4 selectivity of 69.5, which is the highest performance reported for dry-state GO-stacking membranes. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhanced photocatalytic CO2 reduction to CH4 over separated dual co-catalysts Au and RuO2

Science.gov (United States)

Dong, Chunyang; Hu, Songchang; Xing, Mingyang; Zhang, Jinlong

2018-04-01

A spatially separated, dual co-catalyst photocatalytic system was constructed by the stepwise introduction of RuO2 and Au nanoparticles (NPs) at the internal and external surfaces of a three dimensional, hierarchically ordered TiO2-SiO2 (HTSO) framework (the final photocatalyst was denoted as Au/HRTSO). Characterization by HR-TEM, EDS-mapping, XRD and XPS confirmed the existence and spatially separated locations of Au and RuO2. In CO2 photocatalytic reduction (CO2PR), Au/HRTSO (0.8%) shows the optimal performance in both the activity and selectivity towards CH4; the CH4 yield is almost twice that of the singular Au/HTSO or HRTSO (0.8%, weight percentage of RuO2) counterparts. Generally, Au NPs at the external surface act as electron trapping agents and RuO2 NPs at the inner surface act as hole collectors. This advanced spatial configuration could promote charge separation and transfer efficiency, leading to enhanced CO2PR performance in both the yield and selectivity toward CH4 under simulated solar light irradiation.

Effects of temperature and anion species on CO2 permeability and CO2/N2 separation coefficient through ionic liquid membranes

International Nuclear Information System (INIS)

Jindaratsamee, Pinyarat; Shimoyama, Yusuke; Morizaki, Hironobu; Ito, Akira

2011-01-01

The permeability of carbon dioxide (CO 2 ) through imidazolium-based ionic liquid membranes was measured by a sweep gas method. Six species of ionic liquids were studied in this work as follows: [emim][BF 4 ], [bmim][BF 4 ], [bmim][PF 6 ], [bmim][Tf 2 N], [bmim][OTf], and [bmim][dca]. The ionic liquids were supported with a polyvinylidene fluoride porous membrane. The measurements were performed at T = (303.15 to 343.15) K. The partial pressure difference between feed and permeate sides was 0.121 MPa. The permeability of the CO 2 increases with temperature for the all ionic liquid species. Base on solution diffusion theory, it can be explained that the diffusion coefficient of CO 2 in an ionic liquid affects the temperature dependence more strongly than the solubility coefficient. The greatest permeability was obtained with the [bmim][Tf 2 N] membrane. The membrane of [bmim][PF 6 ] presents the lowest permeability. The separation coefficient between CO 2 and N 2 through the ionic liquid membranes was also investigated at the volume fraction of CO 2 at feed side 0.10. The separation coefficient decreases with the increase of temperature for the all ionic liquid species. The membrane of [emim][BF 4 ] and [bmim][BF 4 ] gives the highest separation coefficient at constant temperature. The lowest separation coefficient was obtained from [bmim][Tf 2 N] membrane which presents the highest permeability of CO 2 .

Analysis of CO2 Separation from Flue Gas, Pipeline Transportation, and Sequestration in Coal

Energy Technology Data Exchange (ETDEWEB)

Eric P. Robertson

2007-09-01

This report was written to satisfy a milestone of the Enhanced Coal Bed Methane Recovery and CO2 Sequestration task of the Big Sky Carbon Sequestration project. The report begins to assess the costs associated with separating the CO2 from flue gas and then injecting it into an unminable coal seam. The technical challenges and costs associated with CO2 separation from flue gas and transportation of the separated CO2 from the point source to an appropriate sequestration target was analyzed. The report includes the selection of a specific coal-fired power plant for the application of CO2 separation technology. An appropriate CO2 separation technology was identified from existing commercial technologies. The report also includes a process design for the chosen technology tailored to the selected power plant that used to obtain accurate costs of separating the CO2 from the flue gas. In addition, an analysis of the costs for compression and transportation of the CO2 from the point-source to an appropriate coal bed sequestration site was included in the report.

Microporous carbonaceous adsorbents for CO2 separation via selective adsorption

KAUST Repository

Zhao, Yunfeng; Liu, Xin; Han, Yu

2015-01-01

Selective adsorption of CO2 has important implications for many energy and environment-related processes, which require the separation of CO2 from other gases (e.g. N2 and CH4) with high uptakes and selectivity. The development of high

Recent advances in multi-layer composite polymeric membranes for CO2 separation: A review

Directory of Open Access Journals (Sweden)

Zhongde Dai

2016-07-01

Full Text Available The development of multilayer composite membranes for CO2 separation has gained increasing attention due to the desire for energy efficient technologies. Multilayer composite membranes have many advantages, including the possibility to optimize membrane materials independently by layers according to their different functions and to reduce the overall transport resistance by using ultrathin selective layers, and less limitations on the material mechanical properties and processability. A comprehensive review is required to capture details of the progresses that have already been achieved in developing multilayer composite membranes with improved CO2 separation performance in the past 15–20 years. In this review, various composite membrane preparation methods were compared, advances in composite membranes for CO2/CH4 separation, CO2/N2 and CO2/H2 separation were summarized with detailed data, and challenges facing for the CO2 separation using composite membranes, such as aging, plasticization and long-term stability, were discussed. Finally the perspectives and future research directions for composite membranes were presented. Keywords: Composite membrane, CO2 separation, Membrane fabrication, Membrane aging, Long-term stability

Porous materials with optimal adsorption thermodynamics and kinetics for CO2 separation

KAUST Repository

Nugent, Patrick S.

2013-02-27

The energy costs associated with the separation and purification of industrial commodities, such as gases, fine chemicals and fresh water, currently represent around 15 per cent of global energy production, and the demand for such commodities is projected to triple by 2050 (ref. 1). The challenge of developing effective separation and purification technologies that have much smaller energy footprints is greater for carbon dioxide (CO2) than for other gases; in addition to its involvement in climate change, CO 2 is an impurity in natural gas, biogas (natural gas produced from biomass), syngas (CO/H 2, the main source of hydrogen in refineries) and many other gas streams. In the context of porous crystalline materials that can exploit both equilibrium and kinetic selectivity, size selectivity and targeted molecular recognition are attractive characteristics for CO 2 separation and capture, as exemplified by zeolites 5A and 13X (ref. 2), as well as metal-organic materials (MOMs). Here we report that a crystal engineering or reticular chemistry strategy that controls pore functionality and size in a series of MOMs with coordinately saturated metal centres and periodically arrayed hexafluorosilicate (SiF 6 2-) anions enables a \\'sweet spot\\' of kinetics and thermodynamics that offers high volumetric uptake at low CO2 partial pressure (less than 0.15 bar). Most importantly, such MOMs offer an unprecedented CO 2 sorption selectivity over N2, H 2 and CH 4, even in the presence of moisture. These MOMs are therefore relevant to CO2 separation in the context of post-combustion (flue gas, CO2/N2), pre-combustion (shifted synthesis gas stream, CO 2/H 2) and natural gas upgrading (natural gas clean-up, CO2/CH 4). © 2013 Macmillan Publishers Limited. All rights reserved.

Fermentering af korn øger fordøjeligheden af næringsstoffer

DEFF Research Database (Denmark)

Pedersen, Anni Øyan; Jørgensen, Henry Johs. Høgh; Knudsen, Knud Erik Bach

2010-01-01

Et fordøjelighedsforsøg har vist, at energiværdien af byg og hvede steg ved fermentering. Effekten var størst ved fermentering af byg, hvor fordøjeligheden af organisk stof for enden af tyndtarmen steg statistisk sikkert med 9 %. Ved fermentering af hvede steg fordøjeligheden af organisk stof...... af vand og dels CO2-produktion og dermed tørstoftab. Anbefaling om beregning af energiværdi i fermenteret korn vil blive foretaget ud fra resultaterne af et produktionsforsøg med slagtesvin, som er under publicering. Fosforudnyttelse i fermenteret korn undersøges yderligere i et produktionsforsøg med...

Novel CO2 Separation and Methanation for Oxygen and Fuel Production, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Precision Combustion, Inc. (PCI) proposes a novel efficient, compact, and lightweight MicrolithREG-based CO2 separator and methanation reactor to separate CO2 from...

A database for CO2 Separation Performances of MOFs based on Computational Materials Screening.

Science.gov (United States)

Altintas, Cigdem; Avci, Gokay; Daglar, Hilal; Nemati Vesali Azar, Ayda; Velioglu, Sadiye; Erucar, Ilknur; Keskin, Seda

2018-05-03

Metal organic frameworks (MOFs) have been considered as great candidates for CO2 capture. Considering the very large number of available MOFs, high-throughput computational screening plays a critical role in identifying the top performing materials for target applications in a time-effective manner. In this work, we used molecular simulations to screen the most recent and complete MOF database for identifying the most promising materials for CO2 separation from flue gas (CO2/N2) and landfill gas (CO2/CH4) under realistic operating conditions. We first validated our approach by comparing the results of our molecular simulations for the CO2 uptakes, CO2/N2 and CO2/CH4 selectivities of various types of MOFs with the available experimental data. We then computed binary CO2/N2 and CO2/CH4 mixture adsorption data for the entire MOF database and used these results to calculate several adsorbent selection metrics such as selectivity, working capacity, adsorbent performance score, regenerability, and separation potential. MOFs were ranked based on the combination of these metrics and the top performing MOF adsorbents that can achieve CO2/N2 and CO2/CH4 separations with high performance were identified. Molecular simulations for the adsorption of a ternary CO2/N2/CH4 mixture were performed for these top materials in order to provide a more realistic performance assessment of MOF adsorbents. Structure-performance analysis showed that MOFs with ΔQ>30 kJ/mol, 3.8 A≤PLD≤5 A, 5 A≤LCD≤7.5 A, 0.5≤ϕ≤0.75, SA≤1,000 m2/g, ρ>1 g/cm 3 are the best candidates for selective separation of CO2 from flue gas and landfill gas. This information will be very useful to design novel MOFs with the desired structural features that can lead to high CO2 separation potentials. Finally, an online, freely accessible database https://cosmoserc.ku.edu.tr was established, for the first time in the literature, which reports all computed adsorbent metrics of 3,816 MOFs for CO2/N2, CO2/CH4

Påvisning af PCV2

DEFF Research Database (Denmark)

Neumann, Katrine; Buse, Katja Strøm; Hjulsager, Charlotte Kristiane

2018-01-01

Mængden af PCV2-virus i poolede serumprøver kan anvendes til at finde grise med meget PCV2-virus, hvorimod mængden af PCV2-virus i spyt og fæces er velegnede til at vurdere tilstedeværelsen af eller tidspunktet for en begyndende PCV2-infektion...

Påvisning af PCV2

DEFF Research Database (Denmark)

Neumann, Katrine; Buse, Katja Strøm; Hjulsager, Charlotte Kristiane

Mængden af PCV2-virus i poolede serumprøver kan anvendes til at finde grise med meget PCV2-virus, hvorimod mængden af PCV2-virus i spyt og fæces er velegnede til at vurdere tilstedeværelsen af eller tidspunktet for en begyndende PCV2-infektion...

Separation of CO{sub 2}/N{sub 2} by means of a carbon membrane

Energy Technology Data Exchange (ETDEWEB)

Wall, Y.; Braun, G. [Cologne University of Applied Sciences, Cologne (Germany); Kaltenborn, N.; Voigt, I. [Fraunhofer Institute for Ceramic Technologies and Systems, IKTS, Hermsdorf (Germany); Brunner, G. [Hamburg University of Technology (TUHH), Hamburg (Germany)

2012-03-15

The permeation and separation performance of an ultramicroporous carbon membrane for separation of CO{sub 2}/N{sub 2} mixtures were investigated. The experiments were conducted using the steady-state measurement method with pure gases (dead-end mode) and a CO{sub 2}/N{sub 2} gas mixture (20/80 mol.-%) (cross-flow mode) in the temperature range from 293 K to 363 K and at feed pressures of up to 1.4 MPa and atmospheric pressure on the permeate side. The membrane exhibited a selectivity of about 25 and permeability of about 500 Barrer for CO{sub 2} in the mixture with N{sub 2}. The single-gas measurements do not reflect the membrane performance correctly. An adsorption-selective effect is assumed to be the main separation mechanism. Moreover, membrane-aging effects causing blocking due to pore constrictions through adsorption were observed. These pore constrictions lower the permeability, but they raise the selectivity. Operation at high temperatures leads to a reduction of aging effects. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Mass Spectrum Analysis of CO2 and N2 Using Ion Beam Separator System

International Nuclear Information System (INIS)

Tjipto-Sujitno, BA; Darsono; Agus-Santoso

2000-01-01

The main purpose of this research is to study investigate the massspectrum profile of CO 2 and N 2 emitted from Penning ion source using ionbeam separator. Besides that, it is also identified the compositions of CO 2 and N 2 ion gas and their abundances through their mass spectrum profile,because as we know that these ions are consist of ion of atom or molecule aswell as the their abundances. To get these profiles, the ion beam acceleratedin accelerating tube are passed through magnet separator. After passing themagnet separator, the ion current beam was detected using microampere meter.By scanning the strength of magnetic field, it will be found the currentspectrum profile as a function of magnetic field. From this current spectrum,we can make a mass spectrum profile. From experiment done, it was found thatthe mass spectrum peak of CO 2 and N 2 were C + with m/z = (12.00 ± 0.10)amu, O 2 + = (31.96 ± 0.29) amu, CO 2 + = (43.93 ± 0.31) amu, N + (13.97 ± 0.33) amu, and N 2 + = (28.05 ± 0.18) amu. (author)

Phenol-Formaldehyde Resin-Based Carbons for CO2 Separation at Sub-Atmospheric Pressures

Directory of Open Access Journals (Sweden)

Noelia Álvarez-Gutiérrez

2016-03-01

Full Text Available The challenge of developing effective separation and purification technologies that leave much smaller energy footprints is greater for carbon dioxide (CO2 than for other gases. In addition to its involvement in climate change, CO2 is present as an impurity in biogas and bio-hydrogen (biological production by dark fermentation, in post-combustion processes (flue gas, CO2-N2 and many other gas streams. Selected phenol-formaldehyde resin-based activated carbons prepared in our laboratory have been evaluated under static conditions (adsorption isotherms as potential adsorbents for CO2 separation at sub-atmospheric pressures, i.e., in post-combustion processes or from biogas and bio-hydrogen streams. CO2, H2, N2, and CH4 adsorption isotherms at 25 °C and up to 100 kPa were obtained using a volumetric equipment and were correlated by applying the Sips model. Adsorption equilibrium was then predicted for multicomponent gas mixtures by extending the multicomponent Sips model and the Ideal Adsorbed Solution Theory (IAST in conjunction with the Sips model. The CO2 uptakes of the resin-derived carbons from CO2-CH4, CO2-H2, and CO2-N2 at atmospheric pressure were greater than those of the reference commercial carbon (Calgon BPL. The performance of the resin-derived carbons in terms of equilibrium of adsorption seems therefore relevant to CO2 separation in post-combustion (flue gas, CO2-N2 and in hydrogen fermentation (CO2-H2, CO2-CH4.

Preparation of a Facilitated Transport Membrane Composed of Carboxymethyl Chitosan and Polyethylenimine for CO2/N2 Separation

Directory of Open Access Journals (Sweden)

Jiang-Nan Shen

2013-02-01

Full Text Available The miscibility of carboxymethyl chitosan/polyethylenimine (CMCS/PEI blends was analyzed by FT-IR, TGA and SEM. Defect-free CMCS/PEI blend membranes were prepared with polysulfone (PSf ultrafiltration membranes as support layer for the separation of CO2/N2 mixtures. The results demonstrate that the CMCS/PEI blend is miscible, due to the hydrogen bonding interaction between the two targeted polymers. For the blended membrane without water, the permeability of CO2 gas is 3.6 × 10−7 cm3 cm−2 s−1 cmHg−1 and the corresponding separation factor for CO2 and N2 gas is about 33 at the pressure of 15.2 cmHg. Meanwhile, the blended membrane with water has the better permselectivity. The blended membrane containing water with PEI content of 30 wt% has the permeance of 6.3 × 10−4 cm3 cm−2 s−1 cmHg−1 for CO2 gas and a separation factor of 325 for CO2/N2 mixtures at the same feed pressure. This indicates that the CO2 separation performance of the CMCS/PEI blend membrane is higher than that of other facilitated transport membranes reported for CO2/N2 mixture separation.

Investigational study of the CO2 balance in high temperature CO2 separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

An investigational study was conducted to clarify the adaptable environment and effectivity of technologies of high temperature separation/recovery/reutilization of CO2. In the study, data collection, arrangement and comparison were made of various separation technologies such as the membrane method, absorption method, adsorption method, and cryogenic separation method. With the LNG-fired power generation as an example, the adaptable environment and effectivity were made clear by making models by a process simulator, ASPEN PLUS. Moreover, using this simulator, effects of replacing the conventional steam reforming of hydrocarbon with the CO2 reforming were made clear with the methanol synthesis as an example. As to the rock fixation treatment of high temperature CO2, collection/arrangement were made of the data on the fixation treatment of the CO2 separated at high temperature into basic rocks such as peridotite and serpentinite in order to clarify the adaptable environment and effectivity of the treatment. Besides, a potentiality of the fixation to concrete waste was made clear. 57 refs., 57 figs., 93 tabs.

Zeolitic Imidazolate Framework-8 Membrane for H2/CO2 Separation: Experimental and Modeling

Science.gov (United States)

Lai, L. S.; Yeong, Y. F.; Lau, K. K.; Azmi, M. S.; Chew, T. L.

2018-03-01

In this work, ZIF-8 membrane synthesized through solvent evaporation secondary seeded growth was tested for single gas permeation and binary gases separation of H2 and CO2. Subsequently, a modified mathematical modeling combining the effects of membrane and support layers was applied to represent the gas transport properties of ZIF-8 membrane. Results showed that, the membrane has exhibited H2/CO2 ideal selectivity of 5.83 and separation factor of 3.28 at 100 kPa and 303 K. Besides, the experimental results were fitted well with the simulated results by demonstrating means absolute error (MAE) values ranged from 1.13 % to 3.88 % for single gas permeation and 10.81 % to 21.22 % for binary gases separation. Based on the simulated data, most of the H2 and CO2 gas molecules have transported through the molecular pores of membrane layer, which was up to 70 %. Thus, the gas transport of the gases is mainly dominated by adsorption and diffusion across the membrane.

Microbial electrochemical separation of CO2 for biogas upgrading

DEFF Research Database (Denmark)

Kokkoli, Argyro; Zhang, Yifeng; Angelidaki, Irini

2018-01-01

was obtained at 1.2 V, inlet biogas rate of 0.088 mL/h/mL reactor and NaCl concentration of 100 mM at a 5-day operation. Meanwhile, the organic matter of the domestic wastewater in the anode was almost completely removed at the end. The study demonstrated a new sustainable way to simultaneously upgrade biogas......Biogas upgrading to natural gas quality has been under focus the recent years for increasing the utilization potential of biogas. Conventional methods for CO2 removal are expensive and have environmental challenges, such as increased emissions of methane in the atmosphere with serious greenhouse...... impact. In this study, an innovative microbial electrochemical separation cell (MESC) was developed to in-situ separate and regenerate CO2 via alkali and acid regeneration. The MESC was tested under different applied voltages, inlet biogas rates and electrolyte concentrations. Pure biomethane...

Synthesis and characterization of ZIF-69 membranes and separation for CO2/CO mixture

KAUST Repository

Liu, Yunyang

2010-05-01

Continuous and c-oriented ZIF-69 membranes were successfully synthesized on porous alpha-alumina substrates by an in situ solvothermal method. The membranes were characterized by XRD, SEM and single-gas permeation tests. The BET measurements on crystals taken from the same mother liquor that was used for membrane synthesis yield a Langmuir surface area of 1138 m(2)/g. The stability of the membrane towards heat and different solvents were studied. Single-gas permeation experiments through ZIF-69 membranes were carried out by a vacuum method at room temperature using H-2, CH4, CO, CO2 and SF6, respectively. The permeances were in the order of H-2 > CO2 > CH4 > CO > SF6. The separation of CO2/CO gas mixture was investigated by gas chromatograph (GC) and the permselectivity of CO2/CO was 3.5 +/- 0.1 with CO2 permeance of 3.6 +/- 0.3 x 10(-8) mol m(-2) s(-1) Pa-1 at room temperature. (C) 2010 Elsevier B.V. All rights reserved.

How the oil companies look at CO2 separation and disposal

International Nuclear Information System (INIS)

Kaarstad, O.

2001-01-01

Separation and disposal of CO 2 is a new complex problem, and we should not be surprised that the technology available today does not solve all our problems. Neither should we be surprised that politicians, environmentalists, industry leaders and the general public have problems to digest the idea of underground disposal of CO 2 . The main challenges we are facing are: Reducing the investment and operational costs for CO 2 -separation; Finding solutions that do not create new environmental problems; Finding cheaper methods for transport of medium volumes of C= 2 over long distances; Keep informing the public of the pros and cons of underground disposal; Finding good transition strategies; Look for ways of cooperation between industry, authorities and research organizations to manage the transition period, including adaption of legislation to the new situation

Evaluation of Mars CO2 Capture and Gas Separation Technologies

Science.gov (United States)

Muscatello, Anthony C.; Santiago-Maldonado, Edgardo; Gibson, Tracy; Devor, Robert; Captain, James

2011-01-01

Recent national policy statements have established that the ultimate destination of NASA's human exploration program is Mars. In Situ Resource Utilization (ISRU) is a key technology required to ,enable such missions and it is appropriate to review progress in this area and continue to advance the systems required to produce rocket propellant, oxygen, and other consumables on Mars using the carbon dioxide atmosphere and other potential resources. The Mars Atmospheric Capture and Gas separation project is selecting, developing, and demonstrating techniques to capture and purify Martian atmospheric gases for their utilization for the production of hydrocarbons, oxygen, and water in ISRU systems. Trace gases will be required to be separated from Martian atmospheric gases to provide pure CO2 to processing elements. In addition, other Martian gases, such as nitrogen and argon, occur in concentrations high enough to be useful as buffer gas and should be captured as well. To achieve these goals, highly efficient gas separation processes will be required. These gas separation techniques are also required across various areas within the ISRU project to support various consumable production processes. The development of innovative gas separation techniques will evaluate the current state-of-the-art for the gas separation required, with the objective to demonstrate and develop light-weight, low-power methods for gas separation. Gas separation requirements include, but are not limited to the selective separation of: (1) methane and water from unreacted carbon oxides (C02-CO) and hydrogen typical of a Sabatier-type process, (2) carbon oxides and water from unreacted hydrogen from a Reverse Water-Gas Shift process, (3)/carbon oxides from oxygen from a trash/waste processing reaction, and (4) helium from hydrogen or oxygen from a propellant scavenging process. Potential technologies for the separations include' freezers, selective membranes, selective solvents, polymeric sorbents

Ordered mesoporous silica (OMS) as an adsorbent and membrane for separation of carbon dioxide (CO2).

Science.gov (United States)

Chew, Thiam-Leng; Ahmad, Abdul L; Bhatia, Subhash

2010-01-15

Separation of carbon dioxide (CO(2)) from gaseous mixture is an important issue for the removal of CO(2) in natural gas processing and power plants. The ordered mesoporous silicas (OMS) with uniform pore structure and high density of silanol groups, have attracted the interest of researchers for separation of carbon dioxide (CO(2)) using adsorption process. These mesoporous silicas after functionalization with amino groups have been studied for the removal of CO(2). The potential of functionalized ordered mesoporous silica membrane for separation of CO(2) is also recognized. The present paper reviews the synthesis of mesoporous silicas and important issues related to the development of mesoporous silicas. Recent studies on the CO(2) separation using ordered mesoporous silicas (OMS) as adsorbent and membrane are highlighted. The future prospectives of mesoporous silica membrane for CO(2) adsorption and separation are also presented and discussed. Copyright 2009 Elsevier B.V. All rights reserved.

Membrane Separation of 2-Ethyl Hexyl Amine/1-Decene

KAUST Repository

Bawareth, Bander

2012-12-01

1-Decene is a valuable product in linear alpha olefins plants that is contaminated with 2-EHA (2-ethyl hexyl amine). Using organic solvent nanofiltration membranes for this separation is quite challengeable. A membrane has to be a chemically stable in this environment with reasonable and stable separation factor. This paper shows that Teflon AF 2400 and cellulose acetate produced interesting results in 1-decene/2-EHA separation. The separation factor of Teflon AF 2400 is 3 with a stable permeance of 1.1x10-2 L/(m2·h·bar). Likewise, cellulose acetate gave 2-EHA/1-decene separation factor of 2 with a lower permeance of 3.67x10-3 L/(m2·h·bar). A series of hydrophilic membranes were tested but they did not give any separation due to high degree of swelling of 2-EHA with these polymers. The large swelling causes the membrane to lose its diffusivity selectivity because of an increase in the polymer\\'s chain mobility.

Microbial electrolytic capture, separation and regeneration of CO2 for biogas upgrading

DEFF Research Database (Denmark)

Jin, Xiangdan; Zhang, Yifeng; Li, Xiaohu

2017-01-01

challenges. In this study, an innovative microbial electrolytic system was developed to capture, separate and regenerate CO2 for biogas upgrading without external supply of chemicals, and potentially to treat wastewater. The new system was operated at varied biogas flow rates and external applied voltages....... CO2 was effectively separated from the raw biogas and the CH4 content in the outlet reached as high as 97.0±0.2% at the external voltage of 1.2 V and gas flow rate of 19.6 mL/h. Regeneration of CO2 was also achieved in the regeneration chamber with low pH (1.34±0.04). The relatively low electric...... and potentially expands the application of microbial electrochemical technologies....

Ultrathin Composite Polymeric Membranes for CO2 /N2 Separation with Minimum Thickness and High CO2 Permeance.

Science.gov (United States)

Benito, Javier; Sánchez-Laínez, Javier; Zornoza, Beatriz; Martín, Santiago; Carta, Mariolino; Malpass-Evans, Richard; Téllez, Carlos; McKeown, Neil B; Coronas, Joaquín; Gascón, Ignacio

2017-10-23

The use of ultrathin films as selective layers in composite membranes offers significant advantages in gas separation for increasing productivity while reducing the membrane size and energy costs. In this contribution, composite membranes have been obtained by the successive deposition of approximately 1 nm thick monolayers of a polymer of intrinsic microporosity (PIM) on top of dense membranes of the ultra-permeable poly[1-(trimethylsilyl)-1-propyne] (PTMSP). The ultrathin PIM films (30 nm in thickness) demonstrate CO 2 permeance up to seven times higher than dense PIM membranes using only 0.04 % of the mass of PIM without a significant decrease in CO 2 /N 2 selectivity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Membraneless laminar flow cell for electrocatalytic CO2 reduction with liquid product separation

International Nuclear Information System (INIS)

Monroe, Morgan M; Lobaccaro, Peter; Lum, Yanwei; Ager, Joel W

2017-01-01

The production of liquid fuel products via electrochemical reduction of CO 2 is a potential path to produce sustainable fuels. However, to be practical, a separation strategy is required to isolate the fuel-containing electrolyte produced at the cathode from the anode and also prevent the oxidation products (i.e. O 2 ) from reaching the cathode. Ion-conducting membranes have been applied in CO 2 reduction reactors to achieve this separation, but they represent an efficiency loss and can be permeable to some product species. An alternative membraneless approach is developed here to maintain product separation through the use of a laminar flow cell. Computational modelling shows that near-unity separation efficiencies are possible at current densities achievable now with metal cathodes via optimization of the spacing between the electrodes and the electrolyte flow rate. Laminar flow reactor prototypes were fabricated with a range of channel widths by 3D printing. CO 2 reduction to formic acid on Sn electrodes was used as the liquid product forming reaction, and the separation efficiency for the dissolved product was evaluated with high performance liquid chromatography. Trends in product separation efficiency with channel width and flow rate were in qualitative agreement with the model, but the separation efficiency was lower, with a maximum value of 90% achieved. (paper)

High-throughput Molecular Simulations of MOFs for CO2 Separation: Opportunities and Challenges

Science.gov (United States)

Erucar, Ilknur; Keskin, Seda

2018-02-01

Metal organic frameworks (MOFs) have emerged as great alternatives to traditional nanoporous materials for CO2 separation applications. MOFs are porous materials that are formed by self-assembly of transition metals and organic ligands. The most important advantage of MOFs over well-known porous materials is the possibility to generate multiple materials with varying structural properties and chemical functionalities by changing the combination of metal centers and organic linkers during the synthesis. This leads to a large diversity of materials with various pore sizes and shapes that can be efficiently used for CO2 separations. Since the number of synthesized MOFs has already reached to several thousand, experimental investigation of each MOF at the lab-scale is not practical. High-throughput computational screening of MOFs is a great opportunity to identify the best materials for CO2 separation and to gain molecular-level insights into the structure-performance relationships. This type of knowledge can be used to design new materials with the desired structural features that can lead to extraordinarily high CO2 selectivities. In this mini-review, we focused on developments in high-throughput molecular simulations of MOFs for CO2 separations. After reviewing the current studies on this topic, we discussed the opportunities and challenges in the field and addressed the potential future developments.

Modelanalyser af mobilitet og miljø

DEFF Research Database (Denmark)

Christensen, Linda; Gudmundsson, Henrik

Begrebet bæredygtig transport diskuteres og ved hjælp af persontrafikmodellen ALTRANS belyses mulighederne for at fremme bæredygtig udvikling gennem en række scenarier. Desuden præsenteres en mere detaljeret analyse af ændringer i CO2-belastningen ved forbedring af den kollektive trafiks servicen...

Microbial electrochemical separation of CO2 for biogas upgrading.

Science.gov (United States)

Kokkoli, Argyro; Zhang, Yifeng; Angelidaki, Irini

2018-01-01

Biogas upgrading to natural gas quality has been under focus the recent years for increasing the utilization potential of biogas. Conventional methods for CO 2 removal are expensive and have environmental challenges, such as increased emissions of methane in the atmosphere with serious greenhouse impact. In this study, an innovative microbial electrochemical separation cell (MESC) was developed to in-situ separate and regenerate CO 2 via alkali and acid regeneration. The MESC was tested under different applied voltages, inlet biogas rates and electrolyte concentrations. Pure biomethane was obtained at 1.2V, inlet biogas rate of 0.088mL/h/mL reactor and NaCl concentration of 100mM at a 5-day operation. Meanwhile, the organic matter of the domestic wastewater in the anode was almost completely removed at the end. The study demonstrated a new sustainable way to simultaneously upgrade biogas and treat wastewater which can be used as proof of concept for further investigation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of the 2MACE and TIMI-AF Scores for Composite Clinical Outcomes in Anticoagulated Atrial Fibrillation Patients

DEFF Research Database (Denmark)

Pastori, Daniele; Rivera-Caravaca, José Miguel; Esteve-Pastor, María Asunción

2018-01-01

BACKGROUND: Two risk scores have been developed to predict composite outcomes in atrial fibrillation (AF): the 2MACE and TIMI-AF scores. The aim of this study was to compare the predictive ability of these scores in 2 separate warfarin-treated cohorts (one 'real world', one clinical trial) of AF...... patients.Methods and Results:The 2MACE and TIMI-AF scores were calculated in the 'real-world' ATHERO-AF cohort (n=907), and in the randomized controlled AMADEUS trial (n=2,265). Endpoints were major adverse cardiovascular events (MACEs), net clinical outcomes (NCO) and a combination of them, namely...... showed that the 2MACE and TIMI-AF scores had modest but significant predictive ability for composite outcomes in AF. The clinical usefulness of both scores was similar, but the 2MACE score may be simpler and easy to use....

Polyimide hollow fiber membranes for CO2 separation from wet gas mixtures

Directory of Open Access Journals (Sweden)

F. Falbo

2014-12-01

Full Text Available Matrimid®5218 hollow fiber membranes were prepared using the dry-wet spinning process. The transport properties were measured with pure gases (H2, CO2, N2, CH4 and O2 and with a mixture (30% CO2 and 70% N2 in dry and wet conditions at 25 ºC, 50 ºC, 60 ºC and 75 ºC and up to 600 kPa. Interesting values of single gas selectivity up to 60 ºC (between 31 and 28 for CO2/N2 and between 33 and 30 for CO2/CH4 in dry condition were obtained. The separation factor measured for the mixture was 20% lower compared to the single gas selectivity, in the whole temperature range analyzed. In saturation conditions the data showed that water influences the performance of the membranes, inducing a reduction of the permeance of all gases. Moreover, the presence of water caused a decrease of single gas selectivity and separation factor, although not so significant, highlighting the very high water resistance of hollow fiber membrane modules.

CO2 separation by calcium looping from full and partial fuel oxidation processes

International Nuclear Information System (INIS)

Sivalingam, Senthoorselvan

2013-01-01

This thesis work deals with the research and development of calcium looping process for CO 2 separation from full and partial fuel oxidation based power generation systems. CO 2 is the main greenhouse gas and undoubtedly a major contributor to the global warming. It is estimated that more than one third of the total anthropogenic CO 2 emissions come from fossil fuel based heat and power generation. Moreover, fossil fuels are unlikely to be phased out rapidly, since developing alternative energy sources not only take time but also require huge investments and infrastructure. An alternative way to reduce emissions in a medium term is to capture the CO 2 from fossil fueled power plants and store it away from the atmosphere. This process system combining a bunch of technologies is called carbon capture and storage (CCS). CO 2 capture is an important and costly part of CCS and an array of technologies is considered for this. Calcium looping (CaL) is one of such and seems to offer effective and efficient CO 2 separation from fuel oxidation processes. CaL process involves separation of CO 2 at high temperatures (600-700 C) by calcium sorbents (CaO). CO 2 reacts with CaO in a carbonation process and produces CaCO 3 . In a subsequent thermal regeneration (>850 C) called calcination, the CO 2 is released from CaCO 3 . By alternating carbonations and calcinations over multiple cycles, CO 2 is separated from a gas stream. Moreover, the CaL is realised in industrial scale with dual fluidised bed reactors for CO 2 capture (the carbonator) and sorbent regeneration (the calciner). As a process in the development, research is still required in many aspects from thermodynamic modeling to experimental studies. Research works have been carried out in process simulations, sorbent reactivity and optimisation studies in a controlled reactor environment and process parametric studies in a semi-pilot scale CaL test facility. ASPEN Plus power plant simulations integrating the CaL based CO 2

Ionic liquid-based materials: a platform to design engineered CO2 separation membranes.

Science.gov (United States)

Tomé, Liliana C; Marrucho, Isabel M

2016-05-21

During the past decade, significant advances in ionic liquid-based materials for the development of CO2 separation membranes have been accomplished. This review presents a perspective on different strategies that use ionic liquid-based materials as a unique tuneable platform to design task-specific advanced materials for CO2 separation membranes. Based on compilation and analysis of the data hitherto reported, we provide a judicious assessment of the CO2 separation efficiency of different membranes, and highlight breakthroughs and key challenges in this field. In particular, configurations such as supported ionic liquid membranes, polymer/ionic liquid composite membranes, gelled ionic liquid membranes and poly(ionic liquid)-based membranes are detailed, discussed and evaluated in terms of their efficiency, which is attributed to their chemical and structural features. Finally, an integrated perspective on technology, economy and sustainability is provided.

Recent advances on mixed matrix membranes for CO2 separation

Institute of Scientific and Technical Information of China (English)

Ming Wang; Zhi Wang; Song Zhao; Jixiao Wang; Shichang Wang

2017-01-01

Recent advances on mixed matrix membrane for CO2 separation are reviewed in this paper. To improve CO2 separation performance of polymer membranes, mixedmatrixmembranes (MMMs) are developed. The concept of MMM is illustrated distinctly. Suitable polymer and inorganic or organic fillers for MMMs are summarized.Possible interface morphologies between polymer and filler, and the effect of interface morphologies on gas transport properties of MMMs are summarized. The methods to improve compatibility between polymer and filler are introduced. There are eightmethods including silane coupling, Grignard treatment, incorporation of additive,grafting, in situ polymerization, polydopamine coating, particle fusion approach and polymer functionalization. To achieve higher productivity for industrial application,mixed matrix composite membranes are developed. The recent development on hollow fiber and flat mixedmatrix composite membrane is reviewed in detail. Last, the future trend of MMM is forecasted.

Improvement of CO2/N2 separation performance by polymer matrix cellulose acetate butyrate

Science.gov (United States)

Lee, R. J.; Jawad, Z. A.; Ahmad, A. L.; Ngo, J. Q.; Chua, H. B.

2017-06-01

With the rapid development of modern civilization, carbon dioxide (CO2) is produced in large quantities and mainly generated from industrial sectors. The gas emission is the major contributor to global warming. To address this issue, the membrane technology is implemented for the CO2 removal, due to the energy efficiency and economic advantages presented. Cellulose acetate butyrate (CAB) is selected as the polymeric material, due to the excellent film-forming properties and capable of developing a defect-free layer of neat membrane. This study described the fabrication development of CAB using a wet phase inversion method with different casting conditions. Where the composition of the casting solutions (3-5 wt %) and solvent evaporation time (4-6 min) were determined. The outcomes of these dominant parameters were then used to determine the best CAB membrane for CO2/Nitrogen (N2) separation and supported by the characterization i.e. scanning electron micrograph. Gas permeation measurements showed satisfactory performance for CAB membrane fabricated with 5 min evaporation time and 4 wt% polymer composition (M2). Where, its permeance and selectivity are 120.19 GPU and 3.17, respectively. In summary, this study showed a brief outlined of the future direction and perspective of CAB membrane for CO2/N2 separation.

Use of reverse osmosis membranes for the separation of lemongrass essential oil and supercritical CO2

Directory of Open Access Journals (Sweden)

L.A.V. Sarmento

2004-06-01

Full Text Available Although it is still used very little by industry, the process of essential oil extraction from vegetable matrices with supercritical CO2 is regarded as a potentially viable technique. The operation of separating the extract from the solvent is carried out by reducing the pressure in the system. Separation by membranes is an alternative that offers lower energy consumption and easier operation than traditional methods of separation. Combining the processes essential oil extraction with supercritical CO2 and separation by membranes permits the separation of solvent and oil without the need for large variations in extraction conditions. This results in a large energy savings in the case of solvent repressurisation and reuse. In this study, the effectiveness of reverse osmosis membranes in separating lemongrass essential oil from mixtures with supercritical CO2 was tested. The effects of feed oil concentration and transmembrane pressure on CO2 permeate flux and oil retention were studied for three membrane models.

Preparation of a carbon molecular sieve and application to separation of N2, O2 and CO2 in a fixed bed

Directory of Open Access Journals (Sweden)

Soares J.L.

2003-01-01

Full Text Available The emission of CO2 from power plants that burn fossil fuels is the major cause of the accumulation of CO2 in the atmosphere. The separation of CO2 from CO2/air mixtures can play a key role in alleviating this problem. This separation can be carried out by using suitable adsorbents, such as carbon molecular sieves. In this work, a CMS was prepared by deposition of polyfurfuryl alcohol polymer on activated carbon. After deposition of the polymer, the material was carbonized at 800masculineC for 2 hours. This material was used to separate O2/N2 mixtures and CO2 in a fixed bed at room temperature. Experimental breakthrough curves obtained were fitted to theoretical models in order to establish the main mechanisms of mass transfer. The breakthrough curves showed that it is possible to separate O2, N2 and CO2. The shape of the breakthrough curves was not influenced by the total flow, indicating that the gas contact for the gas mixture was good. The experimental data were fitted to theoretical models and it was established that the main mechanism of mass transfer was intraparticle diffusion.

Porous materials as high performance adsorbents for CO2 capture, gas separation and purification

Science.gov (United States)

Wang, Jun

Global warming resulted from greenhouse gases emission has received a widespread attention. Among the greenhouse gases, CO2 contributes more than 60% to global warming due to its huge emission amount. The flue gas contains about 15% CO2 with N2 as the balance. If CO2 can be separated from flue gas, the benefit is not only reducing the global warming effect, but also producing pure CO2 as a very useful industry raw material. Substantial progress is urgent to be achieved in an industrial process. Moreover, energy crisis is one of the biggest challenges for all countries due to the short life of fossil fuels, such as, petroleum will run out in 50 years and coal will run out in 150 years according to today's speed. Moreover, the severe pollution to the environment caused by burning fossil fuels requires us to explore sustainable, environment-friendly, and facile energy sources. Among several alternative energy sources, natural gas is one of the most promising alternative energy sources due to its huge productivity, abundant feed stock, and ease of generation. In order to realize a substantial adsorption process in industry, synthesis of new adsorbents or modification of existing adsorbent with improved properties has become the most critical issue. This dissertation reports systemic characterization and development of five serials of novel adsorbents with advanced adsorption properties. In chapter 2, nitrogen-doped Hypercross-linking Polymers (HCPs) have been synthesized successfully with non-carcinogenic chloromethyl methyl ether (CME) as the cross-linking agent within a single step. Texture properties, surface morphology, CO2/N2 selectivity, and adsorption heat have been presented and demonstrated properly. A comprehensive discussion on factors that affect the CO2 adsorption and CO2/N 2 separation has also been presented. It was found that high micropore proportion and N-content could effectively enhance CO2 uptake and CO2/N2 separation selectivity. In chapter 3, a

Experimental investigation of CO_2 separation by adsorption methods in natural gas purification

International Nuclear Information System (INIS)

Chen, S.J.; Fu, Y.; Huang, Y.X.; Tao, Z.C.; Zhu, M.

2016-01-01

Highlights: • The ideal swing adsorption tank can improve the adsorption performance. • Pure CO_2 adsorption experimental data agrees well with extended Langmuir model. • Langmuir-Freundlich model correlates CO_2/CH_4 mixture adsorption data fairly well. • The temperature increases in the order swing 2 > swing1 > static for pure CO_2 adsorption. • Swinging the adsorption tank can improve the separation efficiency. - Abstract: CO_2 separation for natural gas purification by the adsorption method was studied in detail using volumetric adsorption apparatus. The crystalline phase and microstructure of the experimental sample were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and Micromeritics ASAP 2020 instrument. The XRD pattern proves that the experimental sample consists of 13X zeolites. The SEM images show that the 13X zeolites expose a large number of micro-channels on the surface of the particles. The microporous volume is 0.22 cm"3 (STP)/g. The ideal swing frequency for the adsorption tank can improve the adsorption performance of an adsorbent compared with a static adsorption tank. The pure CO_2 adsorption experimental data agrees well with the extended Langmuir model. The Langmuir-Freundlich model correlates the CO_2/CH_4 mixture adsorption experimental data fairly well. The relative errors between the simulated results and the experimental data are very little, which indicates that these fitted models are correct. The average selectivity of CO_2/CH_4 in a static and swing adsorption tank are, respectively, 3.57 and 3.93, considerably higher than 1, indicating preferential CO_2 adsorption over CH_4 in CO_2/CH_4 mixtures. This also shows that the swing can improve CO_2 separation for natural gas purification. For the three types of motion status, the temperature of the adsorption tank increased in the order swing 2 > swing1 > static state for pure CO_2 adsorption in 13X zeolites. The temperature variation decreased as the

Composites of ionic liquid and amine-modified SAPO 34 improve CO2 separation of CO2-selective polymer membranes

Science.gov (United States)

Hu, Leiqing; Cheng, Jun; Li, Yannan; Liu, Jianzhong; Zhang, Li; Zhou, Junhu; Cen, Kefa

2017-07-01

Mixed matrix membranes with ionic liquids and molecular sieve particles had high CO2 permeabilities, but CO2 separation from small gas molecules such as H2 was dissatisfied because of bad interfacial interaction between ionic liquid and molecular sieve particles. To solve that, amine groups were introduced to modify surface of molecular sieve particles before loading with ionic liquid. SAPO 34 was adopted as the original filler, and four mixed matrix membranes with different fillers were prepared on the outer surface of ceramic hollow fibers. Both surface voids and hard agglomerations disappeared, and the surface became smooth after SAPO 34 was modified by amine groups and ionic liquid [P66614][2-Op]. Mixed matrix membranes with composites of amine-modified SAPO 34 and ionic liquid exhibited excellent CO2 permeability (408.9 Barrers) and CO2/H2 selectivity (22.1).

Comparison of Miniaturized and Conventional Asymmetrical Flow Field-Flow Fractionation (AF4 Channels for Nanoparticle Separations

Directory of Open Access Journals (Sweden)

Zengchao You

2017-03-01

Full Text Available The performance of a miniaturized channel for the separation of polymer and metal nanoparticles (NP using Asymmetrical Flow Field-Flow Fractionation (AF4 was investigated and compared with a conventional AF4 system. To develop standard separation methods, experimental parameters like cross flow, gradient profile and injection time were varied and optimized. Corresponding chromatographic parameters were calculated and compared. Our results indicate that the chromatographic resolution in the miniaturized channel is lower, whereas significantly shorter analyses time and less solvent consumption were obtained. Moreover, the limit of detection (LOD and limit of quantification (LOQ obtained from hyphenation with a UV-detector are obviously lower than in a conventional channel, which makes the miniaturized channel interesting for trace analysis.

Development and characterization of polyethersulfone/TiO2 mixed matrix membranes for CO2/CH4 separation

Science.gov (United States)

Galaleldin, S.; Mannan, H. A.; Mukhtar, H.

2017-12-01

In this study, mixed matrix membranes comprised of polyethersulfone as the bulk polymer phase and titanium dioxide (TiO2) nanoparticles as the inorganic discontinuous phase were prepared for CO2/CH4 separation. Membranes were synthesized at filler loading of 0, 5, 10 and 15 wt % via dry phase inversion method. Morphology, chemical bonding and thermal characteristics of membranes were scrutinized utilizing different techniques, namely: Field Emission Scanning Electron Microscopy (FESEM), Fourier Transform InfraRed (FTIR) spectra and Thermogravimetric analysis (TGA) respectively. Membranes gas separation performance was evaluated for CO2 and CH4 gases at 4 bar feed pressure. The highest separation performance was achieved by mixed matrix membrane (MMM) at 5 % loading of TiO2.

Catalytic combustion of the retentate gas from a CO2/H2 separation membrane reactor for further CO2 enrichment and energy recovery

International Nuclear Information System (INIS)

Hwang, Kyung-Ran; Park, Jin-Woo; Lee, Sung-Wook; Hong, Sungkook; Lee, Chun-Boo; Oh, Duck-Kyu; Jin, Min-Ho; Lee, Dong-Wook; Park, Jong-Soo

2015-01-01

The CCR (catalytic combustion reaction) of the retentate gas, consisting of 90% CO 2 and 10% H 2 obtained from a CO 2 /H 2 separation membrane reactor, was investigated using a porous Ni metal catalyst in order to recover energy and further enrich CO 2 . A disc-shaped porous Ni metal catalyst, namely Al[0.1]/Ni, was prepared by a simple method and a compact MCR (micro-channel reactor) equipped with a catalyst plate was designed for the CCR. CO 2 and H 2 concentrations of 98.68% and 0.46%, respectively, were achieved at an operating temperature of 400 °C, GHSV (gas-hourly space velocity) of 50,000 h −1 and a H 2 /O 2 ratio (R/O) of 2 in the unit module. In the case of the MCR, a sheet of the Ni metal catalyst was easily installed along with the other metal plates and the concentration of CO 2 in the retentate gas increased up to 96.7%. The differences in temperatures measured before and after the CCR were 31 °C at the product outlet and 19 °C at the N 2 outlet in the MCR. The disc-shaped porous metal catalyst and MCR configuration used in this study exhibit potential advantages, such as high thermal transfer resulting in improved energy recovery rate, simple catalyst preparation, and easy installation of the catalyst in the MCR. - Highlights: • The catalytic combustion of a retentate gas obtained from the H 2 /CO 2 separation membrane. • A disc-shaped porous nickel metal catalyst and a micro-channel reactor for catalytic hydrogen combustion. • CO 2 enrichment up to 98.68% at 400 °C, 50,000 h −1 and H 2 /O 2 ratio of 2.

Constructing robust and highly-selective hydrogel membranes by bioadhesion-inspired method for CO 2 separation

KAUST Repository

Wu, Yingzhen

2018-06-01

Water-swollen hydrogel membranes are good candidates for CO2 separations due to the favorable solubility of CO2 in water. However, the excessive amount of water often causes the poor mechanical property and low selectivity. Herein, we propose a bioadhesion-inspired method to construct robust and high-performance CO2 separation membranes via in situ generation of polydopamine (PDA) nanoaggregates within poly (vinyl alcohol) (PVA) matrix. PDA nanoaggregates entangled with PVA chains and formed hydrogen bonding with hydroxyl groups from PVA chains. Physical cross-linking occurred between PVA chains and PDA nanoaggregates. Compared with the PVA membrane, the PVA-PDA hybrid membrane with the dopamine content of 0.5mol% exhibited a 1.7-fold increase in tensile strength and a 2.2-fold increase in the tensile modulus. The membranes were used for CO2/CH4 separation. The physical cross-linking resulted in a PVA chain rigidification region around PDA nanoaggregates, which hindered the penetration of larger-size gas molecules and thus enhancing the CO2/CH4 selectivity. Moreover, the abundant amine groups from PDA nanoaggregates could facilitate CO2 transport. The optimized hybrid hydrogel membrane exhibited CO2/CH4 selectivity of 43.2, which was 43.85% higher than that of the PVA membrane. The bioadhesion-inspired method opens up new opportunities to exploit the potential application of hydrogel membranes.

Ionic Liquid Confined in Mesoporous Polymer Membrane with Improved Stability for CO2/N2 Separation

Directory of Open Access Journals (Sweden)

Ming Tan

2017-09-01

Full Text Available Supported ionic liquid membranes (SILMs have a promising prospect of application in flue gas separation, owing to its high permeability and selectivity of CO2. However, existing SILMs have the disadvantage of poor stability due to the loss of ionic liquid from the large pores of the macroporous support. In this study, a novel SILM with high stability was developed by confining ionic liquid in a mesoporous polymer membrane. First, a mesoporous polymer membrane derived from a soluble, low-molecular-weight phenolic resin precursor was deposited on a porous Al2O3 support, and then 1-ethyl-3-methylimidazolium tetrafluoroborate ([emim][BF4] was immobilized inside mesopores of phenolic resin, forming the SILM under vacuum. Effects of trans-membrane pressure difference on the SILM separation performance were investigated by measuring the permeances of CO2 and N2. The SILM exhibits a high ideal CO2/N2 selectivity of 40, and an actual selectivity of approximately 25 in a mixed gas (50% CO2 and 50% N2 at a trans-membrane pressure difference of 2.5 bar. Compared to [emim][BF4] supported by polyethersulfone membrane with a pore size of around 0.45 μm, the [emim][BF4] confined in a mesoporous polymer membrane exhibits an improved stability, and its separation performance remained stable for 40 h under a trans-membrane pressure difference of 1.5 bar in a mixed gas before the measurement was intentionally stopped.

Analysis of a New Liquefaction Combined with Desublimation System for CO2 Separation Based on N2/CO2 Phase Equilibrium

Directory of Open Access Journals (Sweden)

Wenchao Yang

2015-09-01

Full Text Available Cryogenic CO2 capture is considered as a promising CO2 capture method due to its energy saving and environmental friendliness. The phase equilibrium analysis of CO2-mixtures at low temperature is crucial for the design and operation of a cryogenic system because it plays an important role in analysis of recovery and purity of the captured CO2. After removal of water and toxic gas, the main components in typical boiler gases are N2/CO2. Therefore, this paper evaluates the reliabilities of different cubic equations of state (EOS and mixing rules for N2/CO2. The results show that Peng-Robinson (PR and Soave-Redlich-Kwong (SRK fit the experimental data well, PR combined with the van der Waals (vdW mixing rule is more accurate than the other models. With temperature decrease, the accuracy of the model improves and the deviation of the N2 vapor fraction is 0.43% at 220 K. Based on the selected calculation model, the thermodynamic properties of N2/CO2 at low temperature are analyzed. According to the results, a new liquefaction combined with a desublimation system is proposed. The total recovery and purity of CO2 production of the new system are satisfactory enough for engineering applications. Additionally, the total energy required by the new system to capture the CO2 is about 3.108 MJ·kg−1 CO2, which appears to be at least 9% lower than desublimation separation when the initial concentration of CO2 is 40%.

The Arabidopsis splicing factors, AtU2AF65, AtU2AF35, and AtSF1 shuttle between nuclei and cytoplasms

KAUST Repository

Park, Hyo-Young

2017-04-21

The Arabidopsis splicing factors, AtU2AF65, AtU2AF35, and AtSF1 shuttle between nuclei and cytoplasms. These proteins also move rapidly and continuously in the nuclei, and their movements are affected by ATP depletion. The U2AF65 proteins are splicing factors that interact with SF1 and U2AF35 proteins to promote U2snRNP for the recognition of the pre-mRNA 3\\' splice site during early spliceosome assembly. We have determined the subcellular localization and movement of these proteins\\' Arabidopsis homologs. It was found that Arabidopsis U2AF65 homologs, AtU2AF65a, and AtU2AF65b proteins interact with AtU2AF35a and AtU2AF35b, which are Arabidopsis U2AF35 homologs. We have examined the mobility of these proteins including AtSF1 using fluorescence recovery after photobleaching and fluorescence loss in photobleaching analyses. These proteins displayed dynamic movements in nuclei and their movements were affected by ATP depletion. We have also demonstrated that these proteins shuttle between nuclei and cytoplasms, suggesting that they may also function in cytoplasm. These results indicate that such splicing factors show very similar characteristics to their human counterparts, suggesting evolutionary conservation.

The Arabidopsis splicing factors, AtU2AF65, AtU2AF35, and AtSF1 shuttle between nuclei and cytoplasms

KAUST Repository

Park, Hyo-Young; Lee, Keh Chien; Jang, Yun Hee; Kim, SoonKap; Thu, May Phyo; Lee, Jeong Hwan; Kim, Jeong-Kook

2017-01-01

The Arabidopsis splicing factors, AtU2AF65, AtU2AF35, and AtSF1 shuttle between nuclei and cytoplasms. These proteins also move rapidly and continuously in the nuclei, and their movements are affected by ATP depletion. The U2AF65 proteins are splicing factors that interact with SF1 and U2AF35 proteins to promote U2snRNP for the recognition of the pre-mRNA 3' splice site during early spliceosome assembly. We have determined the subcellular localization and movement of these proteins' Arabidopsis homologs. It was found that Arabidopsis U2AF65 homologs, AtU2AF65a, and AtU2AF65b proteins interact with AtU2AF35a and AtU2AF35b, which are Arabidopsis U2AF35 homologs. We have examined the mobility of these proteins including AtSF1 using fluorescence recovery after photobleaching and fluorescence loss in photobleaching analyses. These proteins displayed dynamic movements in nuclei and their movements were affected by ATP depletion. We have also demonstrated that these proteins shuttle between nuclei and cytoplasms, suggesting that they may also function in cytoplasm. These results indicate that such splicing factors show very similar characteristics to their human counterparts, suggesting evolutionary conservation.

Annihilation of antiferromagnetic order in LiCoO2 by excess Li

International Nuclear Information System (INIS)

Sugiyama, Jun; Ikedo, Yutaka; Nozaki, Hiroshi; Mukai, Kazuhiko; Andreica, Daniel; Amato, Alex; Menetrier, Michel; Carlier, Dany; Delmas, Claude

2009-01-01

In order to elucidate the origin of antiferromagnetic (AF) order below 30 K in LiCoO 2 , in which all the Co 3+ ions are in a low-spin state with S=0, the magnetic nature of the Li-excess sample Li 1.04 Co 0.96 O 1.96 was studied by muon-spin spectroscopy in the temperature range between 1.8 and 100 K. Although disordered localized moments appeared below 25 K, static AF order was not detected even at 1.8 K. Moreover, a small amount of excess Li ions (4%) and oxygen vacancies (2%) was found to change ∼50% of the sample into a magnetically disordered phase at 1.8 K. The stoichiometric LiCoO 2 , which was prepared from the same starting materials to those for the Li-excess sample, showed an AF transition at 30 K, while the volume fraction of the AF phase was 10% even at 1.8 K. This therefore excludes the possible role of the excess Li + on the formation of static AF order.

High-Throughput Molecular Simulations of Metal Organic Frameworks for CO2 Separation: Opportunities and Challenges

Directory of Open Access Journals (Sweden)

Ilknur Erucar

2018-02-01

Full Text Available Metal organic frameworks (MOFs have emerged as great alternatives to traditional nanoporous materials for CO2 separation applications. MOFs are porous materials that are formed by self-assembly of transition metals and organic ligands. The most important advantage of MOFs over well-known porous materials is the possibility to generate multiple materials with varying structural properties and chemical functionalities by changing the combination of metal centers and organic linkers during the synthesis. This leads to a large diversity of materials with various pore sizes and shapes that can be efficiently used for CO2 separations. Since the number of synthesized MOFs has already reached to several thousand, experimental investigation of each MOF at the lab-scale is not practical. High-throughput computational screening of MOFs is a great opportunity to identify the best materials for CO2 separation and to gain molecular-level insights into the structure–performance relationships. This type of knowledge can be used to design new materials with the desired structural features that can lead to extraordinarily high CO2 selectivities. In this mini-review, we focused on developments in high-throughput molecular simulations of MOFs for CO2 separations. After reviewing the current studies on this topic, we discussed the opportunities and challenges in the field and addressed the potential future developments.

Microbial Electrolytic Capture, Separation and Regeneration of CO2 for Biogas Upgrading.

Science.gov (United States)

Jin, Xiangdan; Zhang, Yifeng; Li, Xiaohu; Zhao, Nannan; Angelidaki, Irini

2017-08-15

Biogas upgrading to natural gas quality is essential for the efficient use of biogas in various applications. Carbon dioxide (CO 2 ) which constitutes a major part of the biogas is generally removed by physicochemical methods. However, most of the methods are expensive and often present environmental challenges. In this study, an innovative microbial electrolytic system was developed to capture, separate and regenerate CO 2 for biogas upgrading without external supply of chemicals, and potentially to treat wastewater. The new system was operated at varied biogas flow rates and external applied voltages. CO 2 was effectively separated from the raw biogas and the CH 4 content in the outlet reached as high as 97.0 ± 0.2% at the external voltage of 1.2 V and gas flow rate of 19.6 mL/h. Regeneration of CO 2 was also achieved in the regeneration chamber with low pH (1.34 ± 0.04). The relatively low electric energy consumption (≤0.15 kWh/m 3 biogas) along with the H 2 production which can contribute to the energy input makes the overall energy need of the system low, and thereby makes the technology promising. This work provides the first attempt for development of a sustainable biogas upgrading technology and potentially expands the application of microbial electrochemical technologies.

Registrering og Benchmarking af Modus 2 Forskning

DEFF Research Database (Denmark)

Duus, Henrik Johannsen; Jørgensen, Jens E.

2004-01-01

Fremvæksten af modus 2 forskning stiller krav om en revurdering af højere læreanstalters evaluerings- og meriteringspraksis. Den endimensionale prioritering af modus 1 forskning såvel som dennes ligeså endimensionale evaluering via publikationer må afvises som utidssvarende. Som en konsekvens her...

CO{sub 2} separation by calcium looping from full and partial fuel oxidation processes

Energy Technology Data Exchange (ETDEWEB)

Sivalingam, Senthoorselvan

2013-06-05

This thesis work deals with the research and development of calcium looping process for CO{sub 2} separation from full and partial fuel oxidation based power generation systems. CO{sub 2} is the main greenhouse gas and undoubtedly a major contributor to the global warming. It is estimated that more than one third of the total anthropogenic CO{sub 2} emissions come from fossil fuel based heat and power generation. Moreover, fossil fuels are unlikely to be phased out rapidly, since developing alternative energy sources not only take time but also require huge investments and infrastructure. An alternative way to reduce emissions in a medium term is to capture the CO{sub 2} from fossil fueled power plants and store it away from the atmosphere. This process system combining a bunch of technologies is called carbon capture and storage (CCS). CO{sub 2} capture is an important and costly part of CCS and an array of technologies is considered for this. Calcium looping (CaL) is one of such and seems to offer effective and efficient CO{sub 2} separation from fuel oxidation processes. CaL process involves separation of CO{sub 2} at high temperatures (600-700 C) by calcium sorbents (CaO). CO{sub 2} reacts with CaO in a carbonation process and produces CaCO{sub 3}. In a subsequent thermal regeneration (>850 C) called calcination, the CO{sub 2} is released from CaCO{sub 3}. By alternating carbonations and calcinations over multiple cycles, CO{sub 2} is separated from a gas stream. Moreover, the CaL is realised in industrial scale with dual fluidised bed reactors for CO{sub 2} capture (the carbonator) and sorbent regeneration (the calciner). As a process in the development, research is still required in many aspects from thermodynamic modeling to experimental studies. Research works have been carried out in process simulations, sorbent reactivity and optimisation studies in a controlled reactor environment and process parametric studies in a semi-pilot scale CaL test facility

Functionalized Mesoporous Silica Membranes for CO2 Separation Applications

Directory of Open Access Journals (Sweden)

Hyung-Ju Kim

2015-01-01

Full Text Available Mesoporous silica molecular sieves are emerging candidates for a number of potential applications involving adsorption and molecular transport due to their large surface areas, high pore volumes, and tunable pore sizes. Recently, several research groups have investigated the potential of functionalized mesoporous silica molecular sieves as advanced materials in separation devices, such as membranes. In particular, mesoporous silica with a two- or three-dimensional pore structure is one of the most promising types of molecular sieve materials for gas separation membranes. However, several important challenges must first be addressed regarding the successful fabrication of mesoporous silica membranes. First, a novel, high throughput process for the fabrication of continuous and defect-free mesoporous silica membranes is required. Second, functionalization of mesopores on membranes is desirable in order to impart selective properties. Finally, the separation characteristics and performance of functionalized mesoporous silica membranes must be further investigated. Herein, the synthesis, characterization, and applications of mesoporous silica membranes and functionalized mesoporous silica membranes are reviewed with a focus on CO2 separation.

Novel Concept For Hydrogen And CO2 Separation

International Nuclear Information System (INIS)

Adam Campen; Kanchan Mondal; Tomasz Wiltowski; Tomasz Wiltowski

2006-01-01

The process was developed for the separation of hydrogen from coal gasification based syngas components for end uses such as clean energy production. The process is flexible such that it can be used within the gasifier to separate hydrogen or as a separate unit process, depending on the requirements of the process design. The basic idea of the research was to design and apply solids to be used in a fixed bed reactor that will increase the hydrogen yield as well as capture greenhouse gases in its matrix through reaction. The end product envisioned in this process is pure hydrogen. The spent solids were then regenerated thermo neutrally while releasing sequestration-ready carbon dioxide. The research involved the validation of the process along with the evaluation of the process parameters to maximize the hydrogen content in the product stream. The effect of sulfur (present as H 2 S) in the product stream on the process efficiency was also evaluated. Most importantly, the solids were designed such that they have the maximum selectivity to the beneficial reactions while maintaining their structure and activity through the reaction-regeneration cycles. Iron (created by reduction of hematite with syngas) was selected as the Boudouard catalyst and CaO was selected as the carbon dioxide removal material. Thermogravimetric (TG) and Temperature Programmed Reduction (TPR) Analysis were utilized to evaluate the reaction rate parameters, and capacity for CO 2 . Specially synthesized CaO (wherein the surface properties were modified) was found to provide better capacity and reaction rates as compared to commercially available CaO. In addition, these specially synthesized CaO-based sorbent showed lower deactivation over multiple cycles. Experiments were also performed with different compositions of syngas to identify the optimal conditions for pure H 2 production. Finally, simultaneous coal gasification and hydrogen enrichment experiments were conducted. It was found that for a

Relation between separation factor of carbon isotope and chemical reaction of CO2 with amine in nonaqueous solvent

International Nuclear Information System (INIS)

Takeshita, Kenji; Kitamoto, Asashi

1989-01-01

The separation factor for carbon isotope exchange reaction between CO 2 and amine in nonaqueous solvent was related to absorption reaction of CO 2 in a solution. The test solutions were mixtures of primary amine (such as butylamine and tert-butylamine) or secondary amine (such as diethylamine, dipropylamine and dibutylamine) diluted with nonpolar solvent (octane or triethyalmine) or polar solvent (methanol), respectively. The isotope exchange reaction consists of three steps related to chemical reaction of CO 2 in amine and nonaqueous solvent mixture, namely the reaction between CO 2 and carbamic acid, that between CO 2 and amine carbamate, and that between CO 2 and carbamic ion. Above all, the isotope separation factor between CO 2 and carbamic acid had the highest value. The overall separation factor can be higher in amine-nonaqueous solvent mixture where the concentration of carbamic acid becomes higher. (author)

Promising monolayer membranes for CO{sub 2}/N{sub 2}/CH{sub 4} separation: Graphdiynes modified respectively with hydrogen, fluorine, and oxygen atoms

Energy Technology Data Exchange (ETDEWEB)

Zhao, Lianming, E-mail: lmzhao@upc.edu.cn; Sang, Pengpeng; Guo, Sheng; Liu, Xiuping; Li, Jing; Zhu, Houyu; Guo, Wenyue, E-mail: wyguo@upc.edu.cn

2017-05-31

Graphical abstract: Graphdiyne monolayer membrane modified by fluorine or oxygen can effectively separate CO{sub 2}/N{sub 2}/CH{sub 4} mixtures. - Highlights: • Three graphdiyne-like membranes were designed and their stabilities were confirmed. • The DFT and MD results claimed a tunable gas separation property of the membranes. • Graphdiyne modified with F or O can effectively separate CO{sub 2}/N{sub 2}/CH{sub 4} mixtures. - Abstract: Three graphdiyne-like monolayers were designed by substituting one-third diacetylenic linkages with heteroatoms hydrogen, fluorine, and oxygen (GDY-X, X = H, F, and O), respectively. The CO{sub 2}/N{sub 2}/CH{sub 4} separation performance of the designed graphdiyne-like monolayers was investigated by using both first-principle density functional theory (DFT) and molecular dynamic (MD) simulations. The stabilities of GDY-X monolayers were confirmed by the calculated cohesive energies and phonon dispersion spectra. Both the DFT and MD calculations demonstrated that although the GDY-H membrane has poor selectivity for CO{sub 2}/N{sub 2}/CH{sub 4} gases, the GDY-F and GDY-O membranes can excellently separate CO{sub 2} and N{sub 2} from CH{sub 4} in a wide temperature range. Moreover, the CO{sub 2}/N{sub 2} mixture can be effectively separated by GDY-O at temperatures lower than 300 K. Based on the kinetic theory, extremely high permeances were found for CO{sub 2} and N{sub 2} passing through the GDY-X membranes (10{sup −4}–10{sup −2} mol/m{sup 2} s Pa at 298 K). In addition, the influence of relative concentration on selectivity was also investigated for gases in the binary mixtures. This work provides an effective way to modify graphdiyne for the separation of large molecular gases, which is quite crucial in the gas separation industry.

Effect of Promoter Concentration on CO2 Separation Using K2CO3 With Reactive Absorption Method in Reactor Packed Column

Directory of Open Access Journals (Sweden)

Monde Junety

2018-01-01

Full Text Available The presence of carbon dioxide (CO2 in the gas is not expected because CO2 can reduce heating value and CO2 is the major emission contributor into the atmosphere. Various separation technologies can be used to reduce CO2 content and improve quality of gas. Chemical or reactive absorption is most widely used because it provides higher removal rate. This paper will study the effect of the addition di ethanolamine (DEA concentration into aqueous 30wt.% potassium carbonate(K2CO3 with reactive absorption method in a reactor packed column at temperature from 40°C to 80°C, DEA concentration range of (1% - 3% and absorbent flow rate (0.5, 0.75 and 1 L. min1. Contacting the gas and absorbent are countercurrent flow in packed column with 1.5 m high and 50 mm in diameter. The absorption column was randomly packed with a packing material raschig rings 5 mm in diameter. The CO2 loading in the liquid samples was determined by titration. It is found that the best result of CO2 loading is 0.065594 mole/mole K2CO3 and CO2 removal 28%. The result show that the loading capacity (mole CO2/mole K2CO3 and CO2 removal increased with the increase of DEA concentration.

Enzymatisk omestring til produktion af biodiesel

DEFF Research Database (Denmark)

Fjerbæk, Lene

2007-01-01

  Biodiesel er i dag sammen med bioethanol et bud på, hvordan transportsektoren kan nedbringe sin netto CO2-emission til atmosfæren og lagrene af fossilt brændstof kan strækkes. På verdensplan forventes der en produktion af biodiesel på 7,9 mio. tons i 2007. Ved den industrielle fremstilling af...... biodiesel benyttes i dag kemiske katalysatorer såsom H2SO4, NaOH, MeONa eller KOH, der efterfølgende fjernes fra den producerede biodiesel med store mængder vand og derved produceres store mængder spildevand. Ved at benytte enzymer i processen kan man reducere mængden af spildevand, der skal renses. Enzymer...... benyttes ikke i de eksisterende processer, men det forventes, at udviklingen af processerne vil øge deres anvendelse i biodieselproduktion. I artiklen præsenteres fordele og ulemper ved anvendelse af enzymer til biodiesel produktion....

Asymmetric Hollow Fiber Membranes for Separation of CO 2 from Hydrocarbons and Fluorocarbons at High-Pressure Conditions Relevant to C 2 F 4 Polymerization

KAUST Repository

Kosuri, Madhava R.

2009-12-02

Separation of high-pressure carbon dioxide from fluorocarbons is important for the production of fluoropolymers such as poly(tetrafluoroethylene). Typical polymeric membranes plasticize under high CO2 partial pressure conditions and fail to provide adequate selective separations. Torlon, a polyamide-imide polymer, with the ability to form interchain hydrogen bonding, is shown to provide stability against aggressive CO2 plasticization. Torlon membranes in the form of asymmetric hollow fibers (the most productive form of membranes) are considered for an intended separation of CO 2/C2F4. To avoid safety issues with tetrafluoroethylene (C2F4), which could detonate under testing conditions, safer surrogate mixtures (C2H2F 2 and C2H4) are considered in this paper. Permeation measurements (at 35 °C) indicate that the Torlon membranes are not plasticized even up to 1250 psi of CO2. The membranes provide mixed gas CO2/C2H2F2 and CO 2/C2H4 selectivities of 100 and 30, respectively, at 1250 psi partial pressures of CO2. On the basis of the measured separation performances of CO2/C2H 2F2 and CO2/C2H4 mixtures, the selectivity of the CO2/C2F4 mixture is expected to be greater than 100. Long-term stability studies indicate that the membranes provide stable separations over a period of 5 days at 1250 psi partial pressures of CO2, thereby making the membrane approach attractive. © 2009 American Chemical Society.

Asymmetric Hollow Fiber Membranes for Separation of CO 2 from Hydrocarbons and Fluorocarbons at High-Pressure Conditions Relevant to C 2 F 4 Polymerization

KAUST Repository

Kosuri, Madhava R.; Koros, William J.

2009-01-01

Separation of high-pressure carbon dioxide from fluorocarbons is important for the production of fluoropolymers such as poly(tetrafluoroethylene). Typical polymeric membranes plasticize under high CO2 partial pressure conditions and fail to provide adequate selective separations. Torlon, a polyamide-imide polymer, with the ability to form interchain hydrogen bonding, is shown to provide stability against aggressive CO2 plasticization. Torlon membranes in the form of asymmetric hollow fibers (the most productive form of membranes) are considered for an intended separation of CO 2/C2F4. To avoid safety issues with tetrafluoroethylene (C2F4), which could detonate under testing conditions, safer surrogate mixtures (C2H2F 2 and C2H4) are considered in this paper. Permeation measurements (at 35 °C) indicate that the Torlon membranes are not plasticized even up to 1250 psi of CO2. The membranes provide mixed gas CO2/C2H2F2 and CO 2/C2H4 selectivities of 100 and 30, respectively, at 1250 psi partial pressures of CO2. On the basis of the measured separation performances of CO2/C2H 2F2 and CO2/C2H4 mixtures, the selectivity of the CO2/C2F4 mixture is expected to be greater than 100. Long-term stability studies indicate that the membranes provide stable separations over a period of 5 days at 1250 psi partial pressures of CO2, thereby making the membrane approach attractive. © 2009 American Chemical Society.

Læremiddelevaluering af web 2.0 læremidler

DEFF Research Database (Denmark)

Falkesgaard Slot, Marie; Gissel, Stig Toke

2014-01-01

Kapitlet etablerer og afprøver et analyseapparat, der bidrager til at højne kvaliteten af de valg, som foretages af web 2.0-læremidler i danskfaget. I kapitlet fokuseres der på læremiddel evaluering af nogle af de funktioner, som typisk tilskrives web 2.0-værktøjerne, ligesom der gives eksempler på...

Preparation and CO{sub 2} adsorption properties of aminopropyl-functionalized mesoporous silica microspheres

Energy Technology Data Exchange (ETDEWEB)

Araki, S.; Doi, H.; Sano, Y.; Tanaka, S.; Miyake, Y. [Hitachi Zosen Corp., Osaka (Japan). Technical Research Institute

2009-11-15

Aminopropyl-functionalized mesoporous silica microspheres (AF-MSM) were synthesized by a simple one-step modified Stober method. Dodecylamine (DDA) was used as the catalyst for the hydrolysis and condensation of the silica source and as the molecular template to prepare the ordered mesopores. The mesoporous silica surfaces were modified to aminopropyl groups by the co-condensation of tetraethoxysilane (TEOS) with 3-aminopropyltriethoxysilane (APTES), up to a maximum of 20 mol.% APTES content in the silica source. The particle size, Brunauer-Emmet-Teller (BET) specific surface area, and mesoporous regularity decreased with increasing APTES content. It is believed that this result is caused by a decreasing amount of DDA incorporated into AF-MSM with increasing APTES content. It was also confirmed that the spherical shape and the mesostructure were maintained even if 20 mol.% of APTES was added to the silica source. Moreover, AF-MSM was applied to the CO{sub 2} adsorbent. The breakthrough time of the CO{sub 2} and CO{sub 2} adsorption capacities increased with increasing APTES content. The adsorption capacity of CO{sub 2} for AF-MSM, prepared at 20 mol.% APTES, was 0.54 mmol g{sup -1}. Carbon dioxide adsorbed onto AF-MSM was completely desorbed by heating in a N{sub 2} purge at 423 K for 30 min.

Preparation of Ethylene Vinyl Acetate/Zeolite 4A Mixed Matrix Membrane for CO2/N2 Separation

Directory of Open Access Journals (Sweden)

Iman Khalilinejad

2016-07-01

Full Text Available A great contribution in research activities on carbon dioxide (CO2 separation, as the most important challenge in greenhouse gases control, has been made to develop new polymeric membranes. In this case, mixed matrix membranes (MMMs, comprised of rigid particles dispersed in a continuous polymeric matrix, was proposed as an effective method to improve the separation properties of polymeric membranes. In this research, ethylene vinyl acetate (EVA copolymer and zeolite 4A powders were applied to prepare MMMs using solution casting/solvent evaporation method and CO2/N2 separation performance of the membranes was examined under different feed pressures (3-8 bar and operating temperatures (25-50°C. Morphological and structural characterizations of the membranes were evaluated using scanning electron microscopy (SEM, Fourier transform infrared (FTIR spectroscopy, differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, density and solvent-induced swelling measurements. The gas permeability measurements through the constant-volume method showed the permeability of two gases increased in the presence of zeolite 4A nanoparticles in the polymer matrix. Calculation of diffusivity coefficients of gases revealed that improvement in the diffusivity of all gases into membrane matrix was the main reason for permeability enhancement. In addition, the increase in the CO2/N2 ideal selectivity with the presence of zeolite 4A nanoparticles in the polymer matrix was attributed to the increment in CO2/N2 diffusion selectivity. Under optimum condition, with the addition of 10 wt% zeolite 4A nanoparticles into the membrane matrix, the CO2 permeability increased from 20.81 to 35.24 Barrer and its related selectivity increased 20% compared to that of neat EVA membrane. Furthermore, the membrane performances increased upon feed pressure rise, while the selectivity decreased with the increase in temperature.

Porous materials with optimal adsorption thermodynamics and kinetics for CO2 separation

KAUST Repository

Nugent, Patrick S.; Belmabkhout, Youssef; Burd, Stephen D.; Cairns, Amy; Luebke, Ryan; Forrest, Katherine A.; Pham, Tony T.; Ma, Shengqian; Space, Brian; Wojtas, Łukasz; Eddaoudi, Mohamed; Zaworotko, Michael J.

2013-01-01

is projected to triple by 2050 (ref. 1). The challenge of developing effective separation and purification technologies that have much smaller energy footprints is greater for carbon dioxide (CO2) than for other gases; in addition to its involvement in climate

Mixed matrix membranes with fast and selective transport pathways for efficient CO2 separation

Science.gov (United States)

Hou, Jinpeng; Li, Xueqin; Guo, Ruili; Zhang, Jianshu; Wang, Zhongming

2018-03-01

To improve CO2 separation performance, porous carbon nanosheets (PCNs) were used as a filler into a Pebax MH 1657 (Pebax) matrix, fabricating mixed matrix membranes (MMMs). The PCNs exhibited a preferential horizontal orientation within the Pebax matrix because of the extremely large 2D plane and nanoscale thickness of the matrix. Therefore, the micropores of the PCNs provided fast CO2 transport pathways, which led to increased CO2 permeability. The reduced pore size of the PCNs was a consequence of the overlapping of PCNs and the polymer chains penetrating into the pores of the PCNs. The reduction in the pore size of the PCNs improved the CO2/gas selectivity. As a result, the CO2 permeability and CO2/CH4 selectivity of the Pebax membrane with 10 wt% PCNs-loading (Pebax-PCNs-10) were 520 barrer and 51, respectively, for CO2/CH4 mixed-gas. The CO2 permeability and CO2/N2 selectivity of the Pebax-PCNs-10 membrane were 614 barrer and 61, respectively, for CO2/N2 mixed-gas.

Mixed-Matrix Membranes for CO2 and H2 Gas Separations Using Metal-Organic Framework and Mesoporus Hybrid Silicas

International Nuclear Information System (INIS)

Musselman, Inga; Balkus, Kenneth Jr.; Ferraris, John

2009-01-01

In this work, we have investigated the separation performance of polymer-based mixed-matrix membranes containing metal-organic frameworks and mesoporous hybrid silicas. The MOF/Matrimid(reg s ign) and MOP-18/Matrimid(reg s ign) membranes exhibited improved dispersion and mechanical strength that allowed high additive loadings with reduced aggregation, as is the case of the 80 wt% MOP-18/Matrimid(reg s ign) and the 80% (w/w) Cu-MOF/Matrimid(reg s ign) membranes. Membranes with up to 60% (w/w) ZIF-8 content exhibited similar mechanical strength and improved dispersion. The H 2 /CO 2 separation properties of MOF/Matrimid(reg s ign) mixed-matrix membranes was improved by either keeping the selectivity constant and increasing the permeability (MOF-5, Cu-MOF) or by improving both selectivity and permeability (ZIF-8). In the case of MOF-5/Matrimid(reg s ign) mixed-matrix membranes, the H 2 /CO 2 selectivity was kept at 2.6 and the H 2 permeability increased from 24.4 to 53.8 Barrers. For the Cu-MOF/Matrimid(reg s ign) mixed-matrix membranes, the H 2 /CO 2 selectivity was kept at 2.05 and the H 2 permeability increased from 17.1 to 158 Barrers. These two materials introduced porosity and uniform paths that enhanced the gas transport in the membranes. When ZIF-8/Matrimid(reg s ign) mixed-matrix membranes were studied, the H 2 /CO 2 selectivity increased from 2.9 to 4.4 and the permeability of H 2 increased from 26.5 to 35.8 Barrers. The increased H 2 /CO 2 selectivity in ZIF-8/Matrimid(reg s ign) membranes was explained by the sieving effect introduced by the ZIF-8 crystals (pore window 0.34 nm) that restricted the transport of molecules larger than H 2 . Materials with microporous and/or mesoporous cavities like carbon aerogel composites with zeolite A and zeolite Y, and membranes containing mesoporous ZSM-5 showed sieving effects for small molecules (e.g. H 2 and CO 2 ), however, the membranes were most selective for CO 2 due to the strong interaction of the zeolites with

Effects of Force Field Selection on the Computational Ranking of MOFs for CO2 Separations.

Science.gov (United States)

Dokur, Derya; Keskin, Seda

2018-02-14

Metal-organic frameworks (MOFs) have been considered as highly promising materials for adsorption-based CO 2 separations. The number of synthesized MOFs has been increasing very rapidly. High-throughput molecular simulations are very useful to screen large numbers of MOFs in order to identify the most promising adsorbents prior to extensive experimental studies. Results of molecular simulations depend on the force field used to define the interactions between gas molecules and MOFs. Choosing the appropriate force field for MOFs is essential to make reliable predictions about the materials' performance. In this work, we performed two sets of molecular simulations using the two widely used generic force fields, Dreiding and UFF, and obtained adsorption data of CO 2 /H 2 , CO 2 /N 2 , and CO 2 /CH 4 mixtures in 100 different MOF structures. Using this adsorption data, several adsorbent evaluation metrics including selectivity, working capacity, sorbent selection parameter, and percent regenerability were computed for each MOF. MOFs were then ranked based on these evaluation metrics, and top performing materials were identified. We then examined the sensitivity of the MOF rankings to the force field type. Our results showed that although there are significant quantitative differences between some adsorbent evaluation metrics computed using different force fields, rankings of the top MOF adsorbents for CO 2 separations are generally similar: 8, 8, and 9 out of the top 10 most selective MOFs were found to be identical in the ranking for CO 2 /H 2 , CO 2 /N 2 , and CO 2 /CH 4 separations using Dreiding and UFF. We finally suggested a force field factor depending on the energy parameters of atoms present in the MOFs to quantify the robustness of the simulation results to the force field selection. This easily computable factor will be highly useful to determine whether the results are sensitive to the force field type or not prior to performing computationally demanding

Enhanced antiferromagnetic coupling in dual-synthetic antiferromagnet with Co2FeAl electrodes

International Nuclear Information System (INIS)

Zhang, D.L.; Xu, X.G.; Wu, Y.; Li, X.Q.; Miao, J.; Jiang, Y.

2012-01-01

We study dual-synthetic antiferromagnets (DSyAFs) using Co 2 FeAl (CFA) Heusler electrodes with a stack structure of Ta/CFA/Ru/CFA/Ru/CFA/Ta. When the thicknesses of the two Ru layers are 0.45 nm, 0.65 nm or 0.45 nm, 1.00 nm, the CFA-based DSyAF has a strong antiferromagnetic coupling between adjacent CFA layers at room temperature with a saturation magnetic field of ∼11,000 Oe, a saturation magnetization of ∼710 emu/cm 3 and a coercivity of ∼2.0 Oe. Moreover, the DSyAF has a good thermal stability up to 400 °C, at which CFA films show B2-ordered structure. Therefore, the CFA-based DSyAFs are favorable for applications in future spintronic devices. - Graphical abstract: Display Omitted Highlights: ► Co 2 FeAl can be applied in room temperature dual-synthetic antiferromagnets. ► Co 2 FeAl dual-synthetic antiferromagnets have a good thermal stability up to 400 °C. ► The Co 2 FeAl has B2-ordered structure in annealed dual-synthetic antiferromagnets.

CORRELATION BETWEEN POLYMER PACKING AND GAS TRANSPORT PROPERTIES FOR CO2/N2 SEPARATION IN GLASSY FLUORINATED POLYIMIDE MEMBRANE

Directory of Open Access Journals (Sweden)

P. C. TAN

2016-07-01

Full Text Available Gas separation performance of a membrane highly hinges on its physical properties. In this study, the interplay between polymer packing of a membrane and its gas transport behaviours (permeability and selectivity was investigated through a series of 6FDA-DAM:DABA (3:2 polyimide membranes with different polymer compactness. The chemical structure and the polymer packing of the resulting membrane were characterized using attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR and packing density measurement, respectively. CO2/N2 separation efficiency of the membrane was evaluated at 25oC with feed pressure up to 6 bar. N2 permeability was found to rely on the membrane’s packing density, which signified its greater dependence on molecular sieving. In contrast, sorption showed a more vital role in determining the CO2 permeability. In this work, the membrane with a final thickness of 97±2 µm had successfully surpassed the Robeson’s 2008 upper bound plot with a CO2 permeability of 83 Barrer and CO2/N2 selectivity of 97 at 3 bar permeation.

What can be learned about carbon cycle climate feedbacks from the CO2 airborne fraction?

Directory of Open Access Journals (Sweden)

N. Gruber

2010-08-01

Full Text Available The ratio of CO2 accumulating in the atmosphere to the CO2 flux into the atmosphere due to human activity, the airborne fraction AF, is central to predict changes in earth's surface temperature due to greenhouse gas induced warming. This ratio has remained remarkably constant in the past five decades, but recent studies have reported an apparent increasing trend and interpreted it as an indication for a decrease in the efficiency of the combined sinks by the ocean and terrestrial biosphere. We investigate here whether this interpretation is correct by analyzing the processes that control long-term trends and decadal-scale variations in the AF. To this end, we use simplified linear models for describing the time evolution of an atmospheric CO2 perturbation. We find firstly that the spin-up time of the system for the AF to converge to a constant value is on the order of 200–300 years and differs depending on whether exponentially increasing fossil fuel emissions only or the sum of fossil fuel and land use emissions are used. We find secondly that the primary control on the decadal time-scale variations of the AF is variations in the relative growth rate of the total anthropogenic CO2 emissions. Changes in sink efficiencies tend to leave a smaller imprint. Therefore, before interpreting trends in the AF as an indication of weakening carbon sink efficiency, it is necessary to account for trends and variations in AF stemming from anthropogenic emissions and other extrinsic forcing events, such as volcanic eruptions. Using atmospheric CO2 data and emission estimates for the period 1959 through 2006, and our simple predictive models for the AF, we find that likely omissions in the reported emissions from land use change and extrinsic forcing events are sufficient to explain the observed long-term trend in AF. Therefore, claims for a decreasing long-term trend in the carbon sink efficiency over the last few decades are currently not supported by

Development of Low Cost Membranes (Ta, Nb & Cellulose Acetate) for H₂/CO₂ Separation in WGS Reactors

Energy Technology Data Exchange (ETDEWEB)

Seetala, Naidu [Grambling State Univ., LA (United States); Siriwardane, Upali [Louisiana Tech Univ., Ruston, LA (United States)

2011-12-15

The main aim of this work is to synthesize low temperature bimetallic nanocatalysts for Water Gas Shift reaction (WGS) for hydrogen production from CO and steam mixture; and develop low-cost metal (Nb/Ta)/ceramic membranes for H₂ separation and Cellulose Acetate membranes for CO₂ separation. .

PEBAX®/PAN Hollow Fiber Membranes for CO2/CH4 Separation

Czech Academy of Sciences Publication Activity Database

Esposito, E.; Clarizia, G.; Bernardo, P.; Jansen, J. C.; Sedláková, Zuzana; Izák, Pavel; Curcio, S.; de Cindio, B.; Tasselli, F.

2015-01-01

Roč. 94, SI (2015), s. 53-61 ISSN 0255-2701. [International Congress of Chemical and Process Engineering CHISA 2014 /21./ and Conference PRES 2014 /17./. Prague, 23.08.2014-27.08.2014] R&D Projects: GA ČR GA14-12695S Grant - others:INRP(IT) MicroPERLA:PON01_01840 Institutional support: RVO:67985858 Keywords : composite membrane * hollow fibers * CO2/CH4 separation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.154, year: 2015

Microporous metal organic framework [M2(hfipbb)2(ted)] (M=Zn, Co; H2hfipbb=4,4-(hexafluoroisopropylidene)-bis(benzoic acid); ted=triethylenediamine): Synthesis, structure analysis, pore characterization, small gas adsorption and CO2/N2 separation properties

Science.gov (United States)

Xu, William W.; Pramanik, Sanhita; Zhang, Zhijuan; Emge, Thomas J.; Li, Jing

2013-04-01

Carbon dioxide is a greenhouse gas that is a major contributor to global warming. Developing methods that can effectively capture CO2 is the key to reduce its emission to the atmosphere. Recent research shows that microporous metal organic frameworks (MOFs) are emerging as a promising family of adsorbents that may be promising for use in adsorption based capture and separation of CO2 from power plant waste gases. In this work we report the synthesis, crystal structure analysis and pore characterization of two microporous MOF structures, [M2(hfipbb)2(ted)] (M=Zn (1), Co (2); H2hfipbb=4,4-(hexafluoroisopropylidene)-bis(benzoic acid); ted=triethylenediamine). The CO2 and N2 adsorption experiments and IAST calculations are carried out on [Zn2(hfipbb)2(ted)] under conditions that mimic post-combustion flue gas mixtures emitted from power plants. The results show that the framework interacts with CO2 strongly, giving rise to relatively high isosteric heats of adsorption (up to 28 kJ/mol), and high adsorption selectivity for CO2 over N2, making it promising for capturing and separating CO2 from CO2/N2 mixtures.

CO{sub 2} separation from exhaust gas; CO{sub 2} separasjon fra eksosgass

Energy Technology Data Exchange (ETDEWEB)

Magelssen, Paul Fr. [Saga Petroleum A/S, Forus (Norway)

1998-07-01

When Saga wanted to reduce the CO{sub 2} emissions from Snorre B, cleaning of CO{sub 2} from exhaust gas was one of several options considered. CO{sub 2} cleaning using membrane/amine technology is under development. Saga required that the technology should be qualified and that the yield of the Snorre B project should not be reduced. This presentation discusses qualification of combined membrane/amine technology, environmental issues, economic issues and implementation on the Snorre B platform. Flue gas from the gas turbine is passed to a CO{sub 2} absorption and desorption stage from which the CO{sub 2} is passed on for compression and disposal while the cleaned flue is let out. The membrane is situated between the flue gas and the absorbent liquid. The pores are large enough for the CO{sub 2} to pass through quickly and small enough to prevent the liquid from penetrating into the pores. The packing factor is high, 500 - 1000 m2/m3, there is no formation of froth, ducts or entrainment of the liquid. New technology implies 65 - 70% size reduction of the main equipment and 39 - 40% reduction of the energy consumption. Research on amines brings out new chemicals which imply 80% reduction in the consumption of chemicals and the quantity of special waste produced. If a CO{sub 2} cleaning plant is installed on a LM 2500, the CO{sub 2} emissions can be reduced by 97,200 ton/year given the right operational conditions. Although it was decided in 1998 not to install the module with the CO{sub 2} pilot cleaning plant, Snorre B is still a good environmental project having CO{sub 2} emission within the values set by Miljoesok.

Effect of Cross-Linking on the Mechanical and Thermal Properties of Poly(amidoamine) Dendrimer/Poly(vinyl alcohol) Hybrid Membranes for CO2 Separation.

Science.gov (United States)

Duan, Shuhong; Kai, Teruhiko; Saito, Takashi; Yamazaki, Kota; Ikeda, Kenichi

2014-04-08

Poly(amidoamine) (PAMAM) dendrimers were incorporated into cross-linked poly(vinyl alcohol) (PVA) matrix to improve carbon dioxide (CO2) separation performance at elevated pressures. In our previous studies, PAMAM/PVA hybrid membranes showed high CO2 separation properties from CO2/H2 mixed gases. In this study, three types of organic Ti metal compounds were selected as PVA cross-linkers that were used to prepare PAMAM/cross-linked PVA hybrid membranes. Characterization of the PAMAM/cross-linked PVA hybrid membranes was conducted using nanoindentation and thermogravimetric analyses. The effects of the cross-linker and CO2 partial pressure in the feed gas on CO2 separation performance were discussed. H2O and CO2 sorption of the PAMAM/PVA hybrid membranes were investigated to explain the obtained CO2 separation efficiencies.

Amino-Functionalized ZIF-7 Nanocrystals: Improved Intrinsic Separation Ability and Interfacial Compatibility in Mixed-Matrix Membranes for CO2 /CH4 Separation.

Science.gov (United States)

Xiang, Long; Sheng, Luqian; Wang, Chongqing; Zhang, Lixiong; Pan, Yichang; Li, Yanshuo

2017-08-01

Highly permeable and selective, as well as plasticization-resistant membranes are desired as promising alternatives for cost- and energy-effective CO 2 separation. Here, robust mixed-matrix membranes based on an amino-functionalized zeolitic imidazolate framework ZIF-7 (ZIF-7-NH 2 ) and crosslinked poly(ethylene oxide) rubbery polymer are successfully fabricated with filler loadings up to 36 wt%. The ZIF-7-NH 2 materials synthesized from in situ substitution of 2-aminobenzimidazole into the ZIF-7 structure exhibit enlarged aperture size compared with monoligand ZIF-7. The intrinsic separation ability for CO 2 /CH 4 on ZIF-7-NH 2 is remarkably enhanced as a result of improved CO 2 uptake capacity and diffusion selectivity. The incorporation of ZIF-7-NH 2 fillers simultaneously makes the neat polymer more permeable and more selective, surpassing the state-of-the-art 2008 Robeson upper bound. The chelating effect between metal (zinc) nodes of fillers and ester groups of a polymer provides good bonding, enhancing the mechanical strength and plasticization resistance of the neat polymer membrane. The developed novel ZIF-7 structure with amino-function and the resulting nanocomposite membranes are very attractive for applications like natural-gas sweetening or biogas purification. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of Cross-Linking on the Mechanical and Thermal Properties of Poly(amidoamine Dendrimer/Poly(vinyl alcohol Hybrid Membranes for CO2 Separation

Directory of Open Access Journals (Sweden)

Shuhong Duan

2014-04-01

Full Text Available Poly(amidoamine (PAMAM dendrimers were incorporated into cross-linked poly(vinyl alcohol (PVA matrix to improve carbon dioxide (CO2 separation performance at elevated pressures. In our previous studies, PAMAM/PVA hybrid membranes showed high CO2 separation properties from CO2/H2 mixed gases. In this study, three types of organic Ti metal compounds were selected as PVA cross-linkers that were used to prepare PAMAM/cross-linked PVA hybrid membranes. Characterization of the PAMAM/cross-linked PVA hybrid membranes was conducted using nanoindentation and thermogravimetric analyses. The effects of the cross-linker and CO2 partial pressure in the feed gas on CO2 separation performance were discussed. H2O and CO2 sorption of the PAMAM/PVA hybrid membranes were investigated to explain the obtained CO2 separation efficiencies.

Analysis of CO{sub 2} separation by means of monoethanolamine wash as an option for reducing the emissions in Germany; Analyse der CO{sub 2}-Abtrennung mittels Monoethanolamin-Waesche als Emissionsminderungsmassnahme in Deutschland

Energy Technology Data Exchange (ETDEWEB)

Nazarko, Jewgeni; Riensche, Ernst; Blum, Ludger; Menzer, Reinhard; Stolten, Detlef [Forschungszentrum Juelich GmbH, Juelich (DE). Inst. fuer Energieforschung - Brennstoffzellen (IEF-3)

2008-07-01

In the year 2006, the utilization of fossil fuels in the power economy in Germany results in CO{sub 2} emissions of 366 million tons. This corresponds to 43.4 % of the entire CO{sub 2} emissions in Germany. In order to reduce the emissions of carbon dioxide at fossil-fuelled power stations significantly, short term retrofits of the plants are to be considered for the separation and storage of CO{sub 2}. From the perspective of the power production, the downstream absorption of CO{sub 2} with monoethanolamine has several advantages: (a) Successful employment of the amine-wash in other industrial's applications; (b) Conventional operation of the power station qualitatively remains unchanged; (c) The downstream separation is the only option for the separation of CO{sub 2} at existing power stations. However, the separation of carbon dioxide results in further material flows and energy flows by means of the absorption in monoethanolamine. In the contribution under consideration, the authors analyze the effects of the absorption of CO{sub 2} in mono ethanol amine on an individual power station as well as on the emissions of the power economy in Germany.

Effect of addition of Proline, ionic liquid [Choline][Pro] on CO2 separation properties of poly(amidoamine) dendrimer / poly(ethylene glycol) hybrid membranes

Science.gov (United States)

Duan, S. H.; Kai, T.; Chowdhury, F. A.; Taniguchi, I.; Kazama, S.

2018-01-01

Poly(amidoamine) (PAMAM) dendrimers were incorporated into cross-linked poly(ethylene glycol) (PEGDMA) matrix to improve carbon dioxide (CO2) separation performance at elevated pressures. In our previous studies, PAMAM/PEGDMA hybrid membranes showed high CO2 separation properties from CO2/H2 mixed gases. In this study, proline, choline and ionic liquid [Choline][Pro] compounds were selected as rate promoters that were used to prepare PAMAM/PEGDMA hybrid membranes. The effect of addition of proline, choline, IL [Choline][Pro] on separation performance of PAMAM/PEGDMA) hybrid membranes for CO2/H2 separation was investigated. Amino acid proline, choline, and IL [Choline][Pro] were used to promote CO2 and amine reaction. With the addition of [Choline][Pro] into PAMAM/PEG membrane, CO2 permeance of PAMAM/PEG hybrid membranes are increased up to 46% without any change of selectivity of membrane for CO2.

Pentiptycene-based polyurethane with enhanced mechanical properties and CO2-plasticization resistance for thin film gas separation membranes.

Science.gov (United States)

Pournaghshband Isfahani, Ali; Sadeghi, Morteza; Wakimoto, Kazuki; Shrestha, Binod Babu; Bagheri, Rouhollah; Sivaniah, Easan; Ghalei, Behnam

2018-04-30

Development of thin film composite (TFC) membranes offers an opportunity to achieve the permeability/selectivity requirements for optimum CO2 separation performance. However, the durability and performance of thin film gas separation membranes are mostly challenged by weak mechanical properties and high CO2 plasticization. Here, we designed new polyurethane (PU) structures with bulky aromatic chain extenders that afford preferred mechanical properties for ultra-thin film formation. An improvement of about 1500% in Young's modulus and 600% in hardness was observed for pentiptycene-based PUs compared to typical PU membranes. Single (CO2, H2, CH4, and N2) and mixed (CO2/N2 and CO2/CH4) gas permeability tests were performed on the PU membranes. The resulting TFC membranes showed a high CO2 permeance up to 1400 GPU (10-6 cm3(STP) cm-2s-1 cmHg-1) and the CO2/N2 and CO2/H2 selectivities of about 22 and 2.1, respectively. The enhanced mechanical properties of pentiptycene-based PUs results in high performance thin membranes with the similar selectivity of the bulk polymer. The thin film membranes prepared from pentiptycene-based PUs also showed a two-fold enhanced plasticization resistance compared to non-pentiptycene containing PU membranes.

Pilot-scale multistage membrane process for the separation of CO2 from LNG-fired flue gas

KAUST Repository

Choi, Seung Hak

2013-06-01

In this study, a multistage pilot-scale membrane plant was constructed and operated for the separation of CO2 from Liquefied Natural Gas (LNG)-fired boiler flue gas of 1000 Nm3/day. The target purity and recovery of CO2 were 99 vol.% and 90%, respectively. For this purpose, asymmetric polyethersulfone (PES) hollow fibers membranes has been developed in our previous work and has evaluated the effects of operating pressure and feed concentration of CO2 on separation performance. The operating and permeation data obtained were also analyzed in relation with the numerical simulation data using countercurrent flow model. Based on these results, in this study, four-staged membrane process including dehumidification process has been designed, installed, and operated to demonstrate the feasibility of multistage membrane systems for removing CO2 from flue gases. The operation results using this plant were compared to the numerical simulation results on multistage membrane process. The experimental results matched well with the numerical simulation data. The concentration and the recovery of CO2 in the permeate stream of final stage were ranged from 95-99 vol.% and 70-95%, respectively, depending on the operating conditions. This study demonstrated the applicability of the membrane-based pilot plant for CO2 recovery from flue gas. © 2013 Elsevier B.V. All rights reserved.

Separation of CO2 in a Solid Waste Management Incineration Facility Using Activated Carbon Derived from Pine Sawdust

Directory of Open Access Journals (Sweden)

Inés Durán

2017-06-01

Full Text Available The selective separation of CO2 from gas mixtures representative of flue gas generated in waste incineration systems is studied on two activated carbons obtained from pine sawdust and compared to a commercial activated carbon. Dynamic adsorption experiments were conducted in a fixed-bed adsorption column using a binary mixture (N2/CO2 with a composition representative of incineration streams at temperatures from 30 to 70 °C. The adsorption behavior of humid mixtures (N2/CO2/H2O was also evaluated in order to assess the influence of water vapor in CO2 adsorption at different relative humidity in the feed gas: 22% and 60%. Moreover, CO2 adsorption was studied in less favorable conditions, i.e., departing from a bed initially saturated with H2O. In addition, the effect of CO2 on H2O adsorption was examined. Experimental results showed that the CO2 adsorption capacity can be reduced significantly by the adsorption of H2O (up to 60% at high relative humidity conditions. On the other hand, the breakthrough tests over the adsorbent initially saturated with water vapor indicated that H2O is little affected by CO2 adsorption. The experimental results pointed out the biomass based carbons as best candidates for CO2 separation under incineration flue gas conditions.

Tail gas treatment of SEWGS technology. Literature review on CO2 and H2S separation

Energy Technology Data Exchange (ETDEWEB)

Fabbri, E.N.; Van Dijk, H.A.J. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

2011-12-15

This literature review is the result of an investigation of the most important way to remove sulphur for the last decades. We will discuss Claus and Claus tail gas process options to solve the problem. Next to solutions which come from membranes, direct oxidation catalysis, from acid gas removal technology, sorbent technology, and liquid oxidation. Each field will be described and explained to understand in which way it could be suitable to separate CO2 and H2S and reach our goals with regard to CO2 transport and storage conditions. Finally, the target of this work will be to propose some interesting and promising solutions in view of future experiments.

Ultem®/ZIF-8 mixed matrix hollow fiber membranes for CO2/N2 separations

KAUST Repository

Dai, Ying

2012-05-01

Organic-inorganic hybrid (mixed matrix) membranes can potentially extend the separation performance of traditional polymeric materials while maintaining processing convenience. Although many dense films studies have been reported, there have been few reported cases of these materials being successfully extended to asymmetric hollow fibers. In this work we report the first successful production of mixed matrix asymmetric hollow fiber membranes containing metal-organic-framework (MOF) ZIF-8 fillers. Specifically, we have incorporated ZIF-8 into a polyetherimide (Ultem ® 1000) matrix and produced dual-layer asymmetric hollow fiber membranes via the dry jet-wet quench method. The outer separating layer of these composite fibers contains 13wt% (17vol%) of ZIF-8 filler. These membranes have been tested over a range of temperatures and pressures for a variety of gas pairs. An increase in separation performance for the CO 2/N 2 gas pairs was observed for both pure gas and mixed gas feeds. © 2012 Elsevier B.V.

Ultem®/ZIF-8 mixed matrix hollow fiber membranes for CO2/N2 separations

KAUST Repository

Dai, Ying; Johnson, J.R.; Karvan, Oğuz; Sholl, David S.; Koros, W.J.

2012-01-01

Organic-inorganic hybrid (mixed matrix) membranes can potentially extend the separation performance of traditional polymeric materials while maintaining processing convenience. Although many dense films studies have been reported, there have been few reported cases of these materials being successfully extended to asymmetric hollow fibers. In this work we report the first successful production of mixed matrix asymmetric hollow fiber membranes containing metal-organic-framework (MOF) ZIF-8 fillers. Specifically, we have incorporated ZIF-8 into a polyetherimide (Ultem ® 1000) matrix and produced dual-layer asymmetric hollow fiber membranes via the dry jet-wet quench method. The outer separating layer of these composite fibers contains 13wt% (17vol%) of ZIF-8 filler. These membranes have been tested over a range of temperatures and pressures for a variety of gas pairs. An increase in separation performance for the CO 2/N 2 gas pairs was observed for both pure gas and mixed gas feeds. © 2012 Elsevier B.V.

Cloning and characterization of two duplicated interleukin-17A/F2 genes in common carp (Cyprinus carpio L.): Transcripts expression and bioactivity of recombinant IL-17A/F2.

Science.gov (United States)

Li, Hongxia; Yu, Juhua; Li, Jianlin; Tang, Yongkai; Yu, Fan; Zhou, Jie; Yu, Wenjuan

2016-04-01

Interleukin-17 (IL-17) plays an important role in inflammation and host defense in mammals. In this study, we identified two duplicated IL-17A/F2 genes in the common carp (Cyprinus carpio) (ccIL-17A/F2a and ccIL-17A/F2b), putative encoded proteins contain 140 amino acids (aa) with conserved IL-17 family motifs. Expression analysis revealed high constitutive expression of ccIL-17A/F2s in mucosal tissues, including gill, skin and intestine, their expression could be induced by Aeromonas hydrophila, suggesting a potential role in mucosal immunity. Recombinant ccIL-17A/F2a protein (rccIL-17A/F2a) produced in Escherichia coli could induce the expression of proinflammatory cytokines (IL-1β) and the antimicrobial peptides S100A1, S100A10a and S100A10b in the primary kidney in a dose- and time-dependent manner. Above findings suggest that ccIL-17A/F2 plays an important role in both proinflammatory and innate immunity. Two duplicated ccIL-17A/F2s showed different expression level with ccIL-17A/F2a higher than b, comparison of two 5' regulatory regions indicated the length from anticipated promoter to transcriptional start site (TSS) and putative transcription factor binding site (TFBS) were different. Promoter activity of ccIL-17A/F2a was 2.5 times of ccIL-17A/F2b which consistent with expression results of two genes. These suggest mutations in 5'regulatory region contributed to the differentiation of duplicated genes. To our knowledge, this is the first report to analyze 5'regulatory region of piscine IL-17 family genes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Toxische Emissionen und entwertete CO2-Neutralität

DEFF Research Database (Denmark)

Czeskleba-Dupont, Rolf

ufuldstændig forbrænding. Under henvisning til en række tidligere og nyere publikationer af forfatteren rekonstrueres derfor de specifikke karakteristika ved problemet dioxin fra forbrændingsprocesser, suppleret gennem argumenter for en tese om, at antagelsen af CO2-neutralitet i tilfældet træforbrænding real......  Arbejdspapiret fremlægger en tese om, at der er registreret en kontraproduktiv effekt af dioxindannelse i kølefasen af brændeovne, som svarer til den de-novo-syntese, der igennem årene er blevet fuldt akcepteret som en mekanisme af dioxindannelsen i affaldsforbrændings-anlæg (AFA). Hvis dette er......-historisk er devalueret. To eksterne dokumenter støtter de fremlagte teser på en generaliserende måde: Det ene dokumenterer en tidlig kritisk tilgang til reguleringen af emissioner fra træforbrænding grundet mange andre emitterede toksiske stoffer og deres sundhedseffekter; det andet evaluerer...

Enhanced Selectivity of the Separation of CO2 from N2 during Crystallization of Semi-Clathrates from Quaternary Ammonium Solutions

International Nuclear Information System (INIS)

Herri, J.M.; Bouchemoua, A.; Kwaterski, M.; Brantuas, P.; Galfre, A.; Bouillot, B.; Douzet, J.; Ouabbas, Y.; Cameirao, A.

2014-01-01

CO 2 mitigation is crucial environmental problem and a societal challenge for this century. CO 2 capture and sequestration is a route to solve a part of the problem, especially for the industries in which the gases to be treated are well localized. CO 2 capture by using hydrate is a process in which the cost of the separation is due to compression of gases to reach the gas hydrate formation conditions. Under pressure, the water and gas forms a solid that encapsulates preferentially CO 2 . The gas hydrate formation requires high pressures and low temperatures, which explains the use of thermodynamic promoters to decrease the operative pressure. Quaternary ammonium salts represent an interesting family of components because of their thermodynamic effect, but also because they can generate crystals that are easily handled. In this work, we have made experiments concerning the equilibrium of (CO 2 , N 2 ) in presence of Tetra-n-Butyl Ammonium Bromide (TBAB) which form a semi-clathrate hydrate. We propose equilibrium data (pressure, temperature) in presence of TBAB at different concentrations and we compare them to the literature. We have also measured the composition of the hydrate phase in equilibrium with the gas phase at different CO 2 concentrations. We observe that the selectivity of the separation is dramatically increased in comparison to the selectivity of the pure water gas clathrate hydrate. We observe also a benefice on the operative pressure which can be dropped down to the atmospheric pressure. (authors)

Analyse af IPCC delrapport 2 - Effekter, klimatilpasning og sårbarhed

DEFF Research Database (Denmark)

Christensen, Jens Hesselbjerg; Arnbjerg-Nielsen, Karsten; Grindsted, Aslak

. Med afsæt i denne delrapport er der udarbejdet en dansk analyse, der nærmere beskriver effekterne af et ændret klima i Danmark suppleret med den seneste danske forskning udført af det danske Center for Regional Changes in the Earth System (CRES). ”Analyse af IPCC delrapport 2 – Effekter...

Unstable maternal environment, separation anxiety, and heightened CO2 sensitivity induced by gene-by-environment interplay.

Directory of Open Access Journals (Sweden)

Francesca R D'Amato

2011-04-01

Full Text Available In man, many different events implying childhood separation from caregivers/unstable parental environment are associated with heightened risk for panic disorder in adulthood. Twin data show that the occurrence of such events in childhood contributes to explaining the covariation between separation anxiety disorder, panic, and the related psychobiological trait of CO(2 hypersensitivity. We hypothesized that early interference with infant-mother interaction could moderate the interspecific trait of response to CO(2 through genetic control of sensitivity to the environment.Having spent the first 24 hours after birth with their biological mother, outbred NMRI mice were cross-fostered to adoptive mothers for the following 4 post-natal days. They were successively compared to normally-reared individuals for: number of ultrasonic vocalizations during isolation, respiratory physiology responses to normal air (20%O(2, CO(2-enriched air (6% CO(2, hypoxic air (10%O(2, and avoidance of CO(2-enriched environments.Cross-fostered pups showed significantly more ultrasonic vocalizations, more pronounced hyperventilatory responses (larger tidal volume and minute volume increments to CO(2-enriched air and heightened aversion towards CO(2-enriched environments, than normally-reared individuals. Enhanced tidal volume increment response to 6%CO(2 was present at 16-20, and 75-90 postnatal days, implying the trait's stability. Quantitative genetic analyses of unrelated individuals, sibs and half-sibs, showed that the genetic variance for tidal volume increment during 6%CO(2 breathing was significantly higher (Bartlett χ = 8.3, p = 0.004 among the cross-fostered than the normally-reared individuals, yielding heritability of 0.37 and 0.21 respectively. These results support a stress-diathesis model whereby the genetic influences underlying the response to 6%CO(2 increase their contribution in the presence of an environmental adversity. Maternal grooming

Domesticeringen af Ford i Danmark:Den kulturelle tilegnelse af Ford og fordismen, 1920-1940

OpenAIRE

Wagner, Michael

2009-01-01

Det amerikanske automobilfirma Ford Motor Company med hovedkvarter i Detroit begyndte at drive forretning i Danmark omkring 1906. De første aktiviteter blev konsolideret samme år ved udnævnelsen af motorforhandleren F. Bülow & Co. til salgsagent i Danmark og importør af Ford automobiler til det skandinaviske marked. Dermed havde Ford tidligt fået et stærkt fodfæste i Nordeuropa, som udviklingen i salget af Ford autobiler de næste årtier til fulde skulle demonstrere. Ford Motor Company er ...

Mixed-linker zeolitic imidazolate framework mixed-matrix membranes for aggressive CO2 separation from natural gas

KAUST Repository

Thompson, Joshua A.

2014-07-01

Zeolitic imidazolate framework (ZIF) materials are a promising subclass of metal-organic frameworks (MOF) for gas separations. However, due to the deleterious effects of gate-opening phenomena associated with organic linker rotation near the limiting pore apertures of ZIFs, there have been few demonstrations of improved gas separation properties over pure polymer membranes when utilizing ZIF materials in composite membranes for CO2-based gas separations. Here, we report a study of composite ZIF/polymer membranes, containing mixed-linker ZIF materials with ZIF-8 crystal topologies but composed of different organic linker compositions. Characterization of the mixed-linker ZIFs shows that the mixed linker approach offers control over the porosity and pore size distribution of the materials, as determined from nitrogen physisorption and Horváth-Kawazoe analysis. Single gas permeation measurements on mixed-matrix membranes reveal that inclusion of mixed-linker ZIFs yields membranes with better ideal CO2/CH4 selectivity than membranes containing ZIF-8. This improvement is shown to likely occur from enhancement in the diffusion selectivity of the membranes associated with controlling the pore size distribution of the ZIF filler. Mixed-gas permeation experiments show that membranes with mixed-linker ZIFs display an effective plasticization resistance that is not typical of the pure polymeric matrix. Overall, we demonstrate that mixed-linker ZIFs can improve the gas separation properties in composite membranes and may be applicable to aggressive CO2 concentrations in natural gas feeds. © 2013 Elsevier Inc. All rights reserved.

Computational Studies of CO 2 Sorption and Separation in an Ultramicroporous Metal–Organic Material

KAUST Repository

Forrest, Katherine A.

2013-08-29

Grand canonical Monte Carlo (GCMC) simulations of CO2 sorption and separation were performed in [Zn(pyz)2SiF6], a metal-organic material (MOM) consisting of a square grid of Zn2+ ions coordinated to pyrazine (pyz) linkers and pillars of SiF6 2- ions. This MOM was recently shown to have an unprecedented selectivity for CO2 over N2, CH4, and H 2 under industrially relevant conditions. The simulated CO 2 sorption isotherms and calculated isosteric heat of adsorption, Qst, values were in excellent agreement with the experimental data for all the state points considered. CO2 saturation in [Zn(pyz) 2SiF6] was achieved at near-ambient temperatures and pressures lower than 1.0 atm. Moreover, the sorbed CO2 molecules were representative of a liquid/fluid under such conditions as confirmed through calculating the isothermal compressibility, βT, values. The simulated CO2 uptakes within CO2/N2 (10:90), CO2/CH4 (50:50), and CO2/H2 (30:70) mixture compositions, characteristic of flue gas, biogas, and syngas, respectively, were comparable to those that were produced in the single-component CO2 sorption simulations. The modeled structure at saturation revealed a loading of 1 CO2 molecule per unit cell. The favored CO2 sorption site was identified as the attraction of the carbon atoms of CO2 molecules to four equatorial fluorine atoms of SiF6 2- anions simultaneously, resulting in CO2 molecules localized at the center of the channel. Furthermore, experimental studies have shown that [Zn(pyz)2SiF6] sorbed minimal amounts of CO2 and N2 at their respective liquid temperatures. Analysis of the crystal structure at 100 K revealed that the unit cell undergoes a slight contraction in all dimensions and contains pyrazine rings that are mildly slanted with an angle of 13.9. Additionally, molecular dynamics (MD) simulations revealed that the sorbate molecules are anchored to the framework at low temperatures, which inhibits diffusion. Thus, it is hypothesized that the sorbed molecules

CO2/N2 Gas Separation Using Nanocomposite Membranes Comprised of Ethylene-Propylene-Diene Monomer/Multi-Walled Carbon Nanotube (EPDM/MWCNT

Directory of Open Access Journals (Sweden)

Zeinab Rajabi

2015-07-01

Full Text Available Nanocomposite membranes of ethylene-propylene-diene monomer/multiwalled carbon nanotubes (EPDM/MWCNT were prepared by solution casting, solvent evaporation and cross-link technique to be applied in CO2/N2 gas separation. Both simple and functionalized MWCNTs have been used. The effect of incorporated different amounts multiwalled carbon nanotubes (0-4 wt%, of both simple and functionalized types, on the performance of nanocomposite membranes was studied. Fourier transform infrared (FTIR spectroscopy and field emission scanning electron microscopy (FESEM were used to evaluate the structural/morphological observations of nanocomposite membranes. Comparing the FTIR results of pure and functionalized nanotubes confirmed the presence of carboxylic groups on the functional carbon nanotubes. The FESEM images indicated that at low concentrations, carbon nanotube particles were dispersed well in the EPDM matrix, but they formed agglomerates at concentrations beyond 1 wt%. By incorporation of MWCNTs, the mechanicalproperties of nanocomposite membranes including tensile strength, Young's modulus and elongation-at-break considerably were improved. By increasing carbon nanotube loading up to 0.75 wt%, the permeability of both CO2 and N2 and the CO2/N2 selectivity increased. Further loading led to higher permeability of CO2/N2, while the selectivity ofthe system decreased that could be attributed to further agglomeration of carbon nanotube particles. Furthermore, functionalization of carbon nanotubes improved their dispersion and the mechanical properties and gas separation performance of nanocomposite membranes. Through functionalizing of MWCNTs, both the CO2 permeability and CO2/N2 selectivity of the optimum membrane (0.75 wt% MWCNTs increased from 37.95 and 18.03 Barrer to 57.57 and 23.43 Barrer, respectively. At ambient temperature, by the increase in feed pressure a slight increase in the permeability of both CO2 and N2 gases was observed, while the CO2

Enhanced Hydrogen Production Integrated with CO2 Separation in a Single-Stage Reactor

Energy Technology Data Exchange (ETDEWEB)

Mahesh Iyer; Himanshu Gupta; Danny Wong; Liang-Shih Fan

2005-09-30

Hydrogen production from coal gasification can be enhanced by driving the equilibrium limited Water Gas Shift reaction forward by incessantly removing the CO{sub 2} by-product via the carbonation of calcium oxide. This project aims at using the OSU patented high-reactivity mesoporous precipitated calcium carbonate sorbent for removing the CO{sub 2} product. Preliminary experiments demonstrate the show the superior performance of the PCC sorbent over other naturally occurring calcium sorbents. Gas composition analyses show the formation of 100% pure hydrogen. Novel calcination techniques could lead to smaller reactor footprint and single-stage reactors that can achieve maximum theoretical H{sub 2} production for multicyclic applications. Sub-atmospheric calcination studies reveal the effect of vacuum level, diluent gas flow rate, thermal properties of the diluent gas and the sorbent loading on the calcination kinetics which play an important role on the sorbent morphology. Steam, which can be easily separated from CO{sub 2}, is envisioned to be a potential diluent gas due to its enhanced thermal properties. Steam calcination studies at 700-850 C reveal improved sorbent morphology over regular nitrogen calcination. A mixture of 80% steam and 20% CO{sub 2} at ambient pressure was used to calcine the spent sorbent at 820 C thus lowering the calcination temperature. Regeneration of calcium sulfide to calcium carbonate was achieved by carbonating the calcium sulfide slurry by bubbling CO{sub 2} gas at room temperature.

U2AF1 mutations alter splice site recognition in hematological malignancies.

Science.gov (United States)

Ilagan, Janine O; Ramakrishnan, Aravind; Hayes, Brian; Murphy, Michele E; Zebari, Ahmad S; Bradley, Philip; Bradley, Robert K

2015-01-01

Whole-exome sequencing studies have identified common mutations affecting genes encoding components of the RNA splicing machinery in hematological malignancies. Here, we sought to determine how mutations affecting the 3' splice site recognition factor U2AF1 alter its normal role in RNA splicing. We find that U2AF1 mutations influence the similarity of splicing programs in leukemias, but do not give rise to widespread splicing failure. U2AF1 mutations cause differential splicing of hundreds of genes, affecting biological pathways such as DNA methylation (DNMT3B), X chromosome inactivation (H2AFY), the DNA damage response (ATR, FANCA), and apoptosis (CASP8). We show that U2AF1 mutations alter the preferred 3' splice site motif in patients, in cell culture, and in vitro. Mutations affecting the first and second zinc fingers give rise to different alterations in splice site preference and largely distinct downstream splicing programs. These allele-specific effects are consistent with a computationally predicted model of U2AF1 in complex with RNA. Our findings suggest that U2AF1 mutations contribute to pathogenesis by causing quantitative changes in splicing that affect diverse cellular pathways, and give insight into the normal function of U2AF1's zinc finger domains. © 2015 Ilagan et al.; Published by Cold Spring Harbor Laboratory Press.

Isotopic separation of carbon by dissociation of CF2HCl irradiated by a Q-modulated CO2 laser

International Nuclear Information System (INIS)

Ezubchenko, A.N.; Ilyukhin, A.I.; Karchevskii, A.I.; Krasnikov, N.S.; Merzylakov, A.V.; Soloukhin, A.B.

1993-01-01

Isotopic separation of carbon by selective dissociation of CF 2 HCl by radiation from a CO 2 laser with mechanical Q-modulation has been studied experimentally. The modulation frequency was 10 4 sec -1 with a 20 W output. The peak radiation intensity is increased by a factor of 20-100 when modulated, while the average power is 0.5-0.9 that of the laser when operating in continuous mode. The authors show that under these conditions, a separation coefficient on the order of 40-50 is achieved as well as a high degree of the target isotope extraction (70%)

A rod-packing microporous hydrogen-bonded organic framework for highly selective separation of C2H2/CO2at room temperature

KAUST Repository

Li, Peng

2014-11-13

Self-assembly of a trigonal building subunit with diaminotriazines (DAT) functional groups leads to a unique rod-packing 3D microporous hydrogen-bonded organic framework (HOF-3). This material shows permanent porosity and demonstrates highly selective separation of C2H2/CO2 at ambient temperature and pressure.

A rod-packing microporous hydrogen-bonded organic framework for highly selective separation of C2H2/CO2at room temperature

KAUST Repository

Li, Peng; He, Yabing; Zhao, Yunfeng; Weng, Linhong; Wang, Hailong; Krishna, Rajamani A A; Wu, Hui; Zhou, Wei; O'Keeffe, Michael A.; Han, Yu; Chen, Banglin

2014-01-01

Self-assembly of a trigonal building subunit with diaminotriazines (DAT) functional groups leads to a unique rod-packing 3D microporous hydrogen-bonded organic framework (HOF-3). This material shows permanent porosity and demonstrates highly selective separation of C2H2/CO2 at ambient temperature and pressure.

CO2 Fixation by Membrane Separated NaCl Electrolysis

DEFF Research Database (Denmark)

Park, Hyun Sic; Lee, Ju Sung; Han, Junyoung

2015-01-01

for converting CO2 into CaCO3 requires high temperature and high pressure as reaction conditions. This study proposes a method to fixate CaCO3 stably by using relatively less energy than existing methods. After forming NaOH absorbent solution through electrolysis of NaCl in seawater, CaCO3 was precipitated...... crystal product was high-purity calcite. The study shows a successful method for fixating CO2 by reducing carbon dioxide released into the atmosphere while forming high-purity CaCO3.......Atmospheric concentrations of carbon dioxide (CO2), a major cause of global warming, have been rising due to industrial development. Carbon capture and storage (CCS), which is regarded as the most effective way to reduce such atmospheric CO2 concentrations, has several environmental and technical...

In-line formation of chemically cross-linked P84® co-polyimide hollow fibre membranes for H2/CO2 separation

KAUST Repository

Choi, Seung Hak

2010-12-13

In this study, chemically cross-linked asymmetric P84® co-polyimide hollow fibre membranes with enhanced separation performance were fabricated, using a dry-wet spinning process with an innovative in-line cross-linking step. The chemical modification was conducted by controlled immersion of the coagulated fibre in an aqueous 1,5-diamino-2-methylpentane (DAMP) cross-linker solution before the take-up. The effect of the cross-linker concentration on the thermal, mechanical, chemical and gas transport properties of the membranes was investigated. FT-IR/ATR analysis was used to identify the chemical changes in the polymer, while DSC analysis confirmed the changes in the Tg and the specific heat of the polymer upon cross-linking. Chemical cross-linking with a 10 wt.% aqueous DAMP solution strongly enhanced the H2/CO2 ideal selectivity from 5.3 to 16.1, while the H2 permeance of the membranes decreased from 7.06 × 10−3 to 1.01 × 10−3 m3(STP) m−2 h−1 bar−1 for a feed pressure of 1 bar at 25 °C. The increase of selectivity with decreasing permeance is somewhat higher than the slope in the Robeson upper bound, evidencing the positive effect of the cross-linking on the separation performance of the fibres. Simultaneously, the cross-linking leads to improved mechanical resistance of the membranes, which could be further enhanced by an additional thermal treatment. The produced membranes are therefore more suitable for use under harsh conditions and have a better overall performance than the uncross-linked ones.

A generic analysis of energy use and solvent selection for CO2 separation from post-combustion flue gases

Science.gov (United States)

Lu, Y.; Chen, S.; Rostam-Abadi, M.

2008-01-01

A thermodynamic calculation was performed to determine the theoretical minimum energy used to separate CO2 from a coal combustion flue gas in a typical adsorption-desorption system. Under ideal conditions, the minimum energy required to separate CO2 from post-combustion flue gas and produce pure CO2 at 1 atmospheric pressure was only about 1183 kJ/kg CO2. This amount could double with the addition of the driving forces of mass and heat transfer and the adverse impacts of absorption heat release on adsorption capacity. Thermodynamic analyses were also performed for the aqueous amine-based absorption process. Two CO2 reaction mechanisms, the carbamate formation reaction with primary/secondary amines and the CO2 hydration reaction with tertiary amines, were included in the absorption reaction. The reaction heat, sensible heat, and stripping heat were all important to the total heat requirement. The heat use of an ideal tertiary amine amounted to 2786 kJ/kg, compared to 3211 kJ/kg for an ideal primary amine. The heat usage of an ideal amine was about 20% lower than that of commercially available amines. Optimizing the absorption process configuration could further reduce energy use. This is an abstract of a paper presented at the 2008 AIChE Spring National Meeting (New Orleans, LA 4/6-10/2008).

Investigations and researches on CO2 balance in a high-temperature carbon dioxide separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With an objective to select a promising process by comparing application environments and effectiveness of a high-temperature carbon dioxide separation, recovery and re-utilization technology with other methods, investigations were performed on reducible amount of carbon dioxide discharge by using material balance and system introduction. A large number of chemical and physical technologies are being developed for the separation and refining methods. This paper discusses the technologies for their application to iron and steel making, oil refining, and petrochemical industries, the so-called heavy and large product industries. As a possibility of utilizing the high-temperature separated CO2 in iron and steel making, an investigation was given on the direct iron ore smelting reduction process. It would be unreasonable to use CO2 in oil refining as a substitute to air to regenerate a catalytic decomposition and reformation catalyst because of decline in the catalytic activity. A discussion was given on a case to replace steam with CO2 in steam reformation and pyrolysis of hydrocarbons. The discussion requires the objective to be focused on such items as C/H ratio at a reformer outlet and relationship of balance in decomposition products. The C1 chemical and others were reviewed to search possibilities for their use as raw materials of chemicals used in chemical industries. Possibilities were discussed to fix high-temperature CO2 into peridotite and serpentine. 42 refs., 32 figs., 11 tabs.

Modellering og måling af metan-emission fra kvæg

DEFF Research Database (Denmark)

Storm, I; Hellwing, Anne Louise Frydendahl; Nielsen, N I

2011-01-01

Udvikling af og kendskab til de metoder, der bruges til måling af kvægs metan-emission udgør en vigtig del af forskningen indenfor området. I dette indlæg præsenteres de mest anvendte metoder til måling og estimation af kvægs metan-emission, herunder modeller, in vitro inkubation, kammer-metoder,......-metoder, SF6-metoden og CO2-metoden. De enkelte metoder beskrives og fordele, ulemper og anvendelsesområder sammenlignes. Dette er vigtig baggrundsinformation for forståelse og fortolkning af øvrige forskningsresultater og for at kunne planlægge fremtidige projekter.......Udvikling af og kendskab til de metoder, der bruges til måling af kvægs metan-emission udgør en vigtig del af forskningen indenfor området. I dette indlæg præsenteres de mest anvendte metoder til måling og estimation af kvægs metan-emission, herunder modeller, in vitro inkubation, kammer...

Poly(ionic liquid)/Ionic Liquid Ion-Gels with High "Free" Ionic Liquid Content: Platform Membrane Materials for CO2/Light Gas Separations.

Science.gov (United States)

Cowan, Matthew G; Gin, Douglas L; Noble, Richard D

2016-04-19

The recycling or sequestration of carbon dioxide (CO2) from the waste gas of fossil-fuel power plants is widely acknowledged as one of the most realistic strategies for delaying or avoiding the severest environmental, economic, political, and social consequences that will result from global climate change and ocean acidification. For context, in 2013 coal and natural gas power plants accounted for roughly 31% of total U.S. CO2 emissions. Recycling or sequestering this CO2 would reduce U.S. emissions by ca. 1800 million metric tons-easily meeting the U.S.'s currently stated CO2 reduction targets of ca. 17% relative to 2005 levels by 2020. This situation is similar for many developed and developing nations, many of which officially target a 20% reduction relative to 1990 baseline levels by 2020. To make CO2 recycling or sequestration processes technologically and economically viable, the CO2 must first be separated from the rest of the waste gas mixture-which is comprised mostly of nitrogen gas and water (ca. 85%). Of the many potential separation technologies available, membrane technology is particularly attractive due to its low energy operating cost, low maintenance, smaller equipment footprint, and relatively facile retrofit integration with existing power plant designs. From a techno-economic standpoint, the separation of CO2 from flue gas requires membranes that can process extremely high amounts of CO2 over a short time period, a property defined as the membrane "permeance". In contrast, the membrane's CO2/N2 selectivity has only a minor effect on the overall cost of some separation processes once a threshold permeability selectivity of ca. 20 is reached. Given the above criteria, the critical properties when developing membrane materials for postcombustion CO2 separation are CO2 permeability (i.e., the rate of CO2 transport normalized to the material thickness), a reasonable CO2/N2 selectivity (≥20), and the ability to be processed into defect-free thin

Study of supercritical CO2 extraction and nanofiltration membrane separation coupling

International Nuclear Information System (INIS)

Sarrade, S.

1994-12-01

The aim of this thesis is to study the coupling of two extraction techniques, nanofiltering and supercritical fluids, designing and building an experimental device that enables both supercritical CO 2 extraction and nanofiltering membrane separation. The purpose is to reach high splitting up levels on small molecule mixtures. The document is divided in four parts : a bibliographic study on these two techniques; a description of the membranes and the products, as well as the experimental device; the characterization and modelization of transfer mechanism in aqueous solutions; a presentation of the results obtained by coupling the two techniques. (TEC). 45 tabs., 70 figs., 98 refs

Separation of glycosidic catiomers by TWIM-MS using CO2 as a drift gas.

Science.gov (United States)

Bataglion, Giovana A; Souza, Gustavo Henrique Martins Ferreira; Heerdt, Gabriel; Morgon, Nelson H; Dutra, José Diogo Lisboa; Freire, Ricardo Oliveira; Eberlin, Marcos N; Tata, Alessandra

2015-02-01

Traveling wave ion mobility mass spectrometry (TWIM-MS) is shown to be able to separate and characterize several isomeric forms of diterpene glycosides stevioside (Stv) and rebaudioside A (RebA) that are cationized by Na(+) and K(+) at different sites. Determination and characterization of these coexisting isomeric species, herein termed catiomers, arising from cationization at different and highly competitive coordinating sites, is particularly challenging for glycosides. To achieve this goal, the advantage of using CO2 as a more massive and polarizable drift gas, over N2, was demonstrated. Post-TWIM-MS/MS experiments were used to confirm the separation. Optimization of the possible geometries and cross-sectional calculations for mobility peak assignments were also performed. Copyright © 2015 John Wiley & Sons, Ltd.

Synthesis and characterization of ceramic-supported and metal-supported membrane layers for the separation of CO{sub 2} in fossil-fuel power plants; Herstellung und Charakterisierung von keramik- und metallgestuetzten Membranschichten fuer die CO{sub 2}-Abtrennung in fossilen Kraftwerken

Energy Technology Data Exchange (ETDEWEB)

Hauler, Felix

2010-07-01

The separation of CO{sub 2} in fossil fuel power plants has become a very important issue due to the contribution of this greenhouse gas to global warming. Thin microporous membranes are promising candidates for separating CO{sub 2} from gas flow before being exhausted into the atmosphere. The membrane demands are good permeation and separation properties and high stability under operation conditions. Novel sol-gel derived materials composed of TiO{sub 2}/ZrO{sub 2} and stabilized SiO{sub 2} seem to be promising due to their good chemical stability and microporous character, especially for the separation of H{sub 2} and CO{sub 2}. Metallic substrates should be preferred as membrane support because they exhibit practical advantages combining good mechanical stability and the benefit of facilitated joining. The present thesis deals with the development of sol-gel derived microporous membrane layers on ceramic and metallic supports for the separation of CO{sub 2}. In this context, the optimized preparation of high-quality membranes with TiO{sub 2}/ZrO{sub 2} and Ni, Co, Zr, Ti doped SiO{sub 2} top layers is presented. These multilayered membranes consist of a graded pore structure to provide a smooth transition of the pore size from the support to the functional layer. Due to the good surface properties, the ceramic substrates only need one interlayer, whereas the rough metallic substrates exhibiting larger pores require a total of three interlayers to obtain an enhanced surface quality. On both types of supports, crack-free functional layers with a thickness below 100 nm were deposited by dip-coating. The unsupported and supported sol-gel materials used for the top layers were investigated in terms of structural properties by thermal analysis, sorption measurements, X-ray diffraction and electron microscopy. Gas permeation tests with He, H{sub 2}, CO{sub 2} und N{sub 2} were carried out to determine the membrane performance with regard to permeation rates and

Emissioner af SO2 og NOX fra kraftværker

DEFF Research Database (Denmark)

Illerup, J. B.; Bruun, H. G.

Rapporten indeholder beregninger af SO2- og NOx- emissioner fra kraftværker, der er reguleret af kvoteloven. Emissionerne er for tre forskellige produktionsscenarier beregnet ud fra emissionsfaktorer baseret på EU-direktivet om store forbrændingsanlæg og emissionsfaktorer beregnet ud fra en...

Geological Sequestration Training and Research Program in Capture and Transport: Development of the Most Economical Separation Method for CO2 Capture

Energy Technology Data Exchange (ETDEWEB)

Vahdat, Nader

2013-09-30

The project provided hands-on training and networking opportunities to undergraduate students in the area of carbon dioxide (CO2) capture and transport, through fundamental research study focused on advanced separation methods that can be applied to the capture of CO2 resulting from the combustion of fossil-fuels for power generation . The project team’s approach to achieve its objectives was to leverage existing Carbon Capture and Storage (CCS) course materials and teaching methods to create and implement an annual CCS short course for the Tuskegee University community; conduct a survey of CO2 separation and capture methods; utilize data to verify and develop computer models for CO2 capture and build CCS networks and hands-on training experiences. The objectives accomplished as a result of this project were: (1) A comprehensive survey of CO2 capture methods was conducted and mathematical models were developed to compare the potential economics of the different methods based on the total cost per year per unit of CO2 avoidance; and (2) Training was provided to introduce the latest CO2 capture technologies and deployment issues to the university community.

CO2 CAPTURE PROJECT - AN INTEGRATED, COLLABORATIVE TECHNOLOGY DEVELOPMENT PROJECT FOR NEXT GENERATION CO2 SEPARATION, CAPTURE AND GEOLOGIC SEQUESTRATION

Energy Technology Data Exchange (ETDEWEB)

Dr. Helen Kerr

2003-08-01

The CO{sub 2} Capture Project (CCP) is a joint industry project, funded by eight energy companies (BP, ChevronTexaco, EnCana, Eni, Norsk Hydro, Shell, Statoil, and Suncor) and three government agencies (1) European Union (DG Res & DG Tren), (2) Norway (Klimatek) and (3) the U.S.A. (Department of Energy). The project objective is to develop new technologies, which could reduce the cost of CO{sub 2} capture and geologic storage by 50% for retrofit to existing plants and 75% for new-build plants. Technologies are to be developed to ''proof of concept'' stage by the end of 2003. The project budget is approximately $24 million over 3 years and the work program is divided into eight major activity areas: (1) Baseline Design and Cost Estimation--defined the uncontrolled emissions from each facility and estimate the cost of abatement in $/tonne CO{sub 2}. (2) Capture Technology, Post Combustion: technologies, which can remove CO{sub 2} from exhaust gases after combustion. (3) Capture Technology, Oxyfuel: where oxygen is separated from the air and then burned with hydrocarbons to produce an exhaust with high CO{sub 2} for storage. (4) Capture Technology, Pre -Combustion: in which, natural gas and petroleum coke are converted to hydrogen and CO{sub 2} in a reformer/gasifier. (5) Common Economic Model/Technology Screening: analysis and evaluation of each technology applied to the scenarios to provide meaningful and consistent comparison. (6) New Technology Cost Estimation: on a consistent basis with the baseline above, to demonstrate cost reductions. (7) Geologic Storage, Monitoring and Verification (SMV): providing assurance that CO{sub 2} can be safely stored in geologic formations over the long term. (8) Non-Technical: project management, communication of results and a review of current policies and incentives governing CO{sub 2} capture and storage. Technology development work dominated the past six months of the project. Numerous studies are making

Stepwise observation and quantification and mixed matrix membrane separation of CO2 within a hydroxy-decorated porous host.

Science.gov (United States)

Morris, Christopher G; Jacques, Nicholas M; Godfrey, Harry G W; Mitra, Tamoghna; Fritsch, Detlev; Lu, Zhenzhong; Murray, Claire A; Potter, Jonathan; Cobb, Tom M; Yuan, Fajin; Tang, Chiu C; Yang, Sihai; Schröder, Martin

2017-04-01

The identification of preferred binding domains within a host structure provides important insights into the function of materials. State-of-the-art reports mostly focus on crystallographic studies of empty and single component guest-loaded host structures to determine the location of guests. However, measurements of material properties ( e.g. , adsorption and breakthrough of substrates) are usually performed for a wide range of pressure (guest coverage) and/or using multi-component gas mixtures. Here we report the development of a multifunctional gas dosing system for use in X-ray powder diffraction studies on Beamline I11 at Diamond Light Source. This facility is fully automated and enables in situ crystallographic studies of host structures under (i) unlimited target gas loadings and (ii) loading of multi-component gas mixtures. A proof-of-concept study was conducted on a hydroxyl-decorated porous material MFM-300(V III ) under (i) five different CO 2 pressures covering the isotherm range and (ii) the loading of equimolar mixtures of CO 2 /N 2 . The study has successfully captured the structural dynamics underpinning CO 2 uptake as a function of surface coverage. Moreover, MFM-300(V III ) was incorporated in a mixed matrix membrane (MMM) with PIM-1 in order to evaluate the CO 2 /N 2 separation potential of this material. Gas permeation measurements on the MMM show a great improvement over the bare PIM-1 polymer for CO 2 /N 2 separation based on the ideal selectivity.

Enhancing visible light photocatalytic and photocharge separation of (BiO)_2CO_3 plate via dramatic I"− ions doping effect

International Nuclear Information System (INIS)

Liang, Lei; Cao, Jing; Lin, Haili; Guo, Xiaomin; Zhang, Meiyu; Chen, Shifu

2016-01-01

Highlights: • Novel I-(BiO)_2CO_3 was prepared by a facile chemical precipitation method. • I"− ions impurity level located on the top of valence band of (BiO)_2CO_3. • I"− ions doping largely improved photocatalytic activity of I-(BiO)_2CO_3. • I-(BiO)_2CO_3 displayed excellent photocharge separation efficiency. - Abstract: Novel I"− ions doped (BiO)_2CO_3 (I-(BiO)_2CO_3) photocatalysts were successfully synthesized via a facile chemical precipitation method. Under visible light (λ > 400 nm), I-(BiO)_2CO_3 displayed much higher activity for rhodamine B and dichlorophenol degradation than the undoped (BiO)_2CO_3. The pseudo-first-order rate constant k_a_p_p of RhB degradation over 15.0% I-(BiO)_2CO_3 was 0.54 h"−"1, which is 11.3 times higher than that of (BiO)_2CO_3. The doped I"− ions formed an impurity level on the top of valence band of (BiO)_2CO_3 and induced much more visible light to be absorbed. The enhanced photocurrent and surface photovoltage properties were detected, which strongly ensures the efficient separation of electrons and holes in I-(BiO)_2CO_3 system under visible light. It provides a facile way to improve the photocatalytic activity of the wide-band-gap (BiO)_2CO_3 via intense doping effect of I"− ions.

Afs password expiration starts Feb 2nd 2004

CERN Multimedia

2004-01-01

Due to security reasons, and in agreement with CERN management, afs/lxplus passwords will fall into line with Nice/Mail passwords on February 2nd and expire annually. As of the above date afs account holders who have not changed their passwords for over a year will have a 60 day grace period to make a change. Following this date their passwords will become invalid. What does this mean to you? If you have changed your afs password in the past 10 months the only difference is that 60 days before expiration you will receive a warning message. Similar warnings will also appear nearer the time of expiration. If you have not changed your password for more than 10 months, then, as of February 2nd you will have 60 days to change it using the command ‘kpasswd'. Help to choose a good password can be found at: http://security.web.cern.ch/security/passwords/ If you have been given a temporary password at any time by the Helpdesk or registration team this will automatically fall into the expiration category ...

Improved solar-driven photocatalytic performance of Ag_2CO_3/(BiO)_2CO_3 prepared in-situ

International Nuclear Information System (INIS)

Zhong, Junbo; Li, Jianzhang; Huang, Shengtian; Cheng, Chaozhu; Yuan, Wei; Li, Minjiao; Ding, Jie

2016-01-01

Highlights: • Ag_2CO_3/(BiO)_2CO_3 photocatalysts were prepared in-situ. • The photo-induced charge separation rate has been greatly increased. • The photocatalytic activity has been greatly promoted. - Abstract: Ag_2CO_3/(BiO)_2CO_3 composites have been fabricated in-situ via a facile parallel flaw co-precipitation method. The specific surface area, structure, morphology, and the separation rate of photo-induced charge pairs of the photocatalysts were characterized by Brunauer–Emmett–Teller (BET) method, X-ray diffraction (XRD), UV–vis diffuse reflectance spectroscopy(DRS), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and surface photovoltage (SPV) spectroscopy, respectively. XRD patterns and DRS demonstrated that Ag_2CO_3 has no effect on the crystal phase and bandgap of (BiO)_2CO_3. The existence of Ag_2CO_3 in the composites enhances the separation rate of photo-induced charge pairs of the photocatalysts. The photocatalytic performance of Ag_2CO_3/(BiO)_2CO_3 was evaluated by the decolorization of methyl orange (MO) aqueous solution under simulated solar irradiation. It was found that the simulated solar-induced photocatalytic activity of Ag_2CO_3/(BiO)_2CO_3 copmposites was significantly improved, which was mainly attributed to the enhanced surface area and the separation rate of photo-induced charge pairs.

High temperature H2/CO2 separation using cobalt oxide silica membranes

Energy Technology Data Exchange (ETDEWEB)

Smart, S.; Diniz da Costa, J.C. [The University of Queensland, FIMLab - Films and Inorganic Membrane Laboratory, School of Chemical Engineering, Brisbane, Qld 4072 (Australia); Vente, J.F. [Energy research Centre of the Netherlands ECN, P.O. Box 1, 1755 ZG Petten (Netherlands)

2012-09-15

In this work high quality cobalt oxide silica membranes were synthesized on alumina supports using a sol-gel, dip coating method. The membranes were subsequently connected into a steel module using a graphite based proprietary sealing method. The sealed membranes were tested for single gas permeance of He, H2, N2 and CO2 at temperatures up to 600C and feed pressures up to 600 kPa. Pressure tests confirmed that the sealing system was effective as no gas leaks were observed during testing. A H2 permeance of 1.9 x 10{sup -7} mol m{sup -2} s{sup -1} Pa-1 was measured in conjunction with a H2/CO2 permselectivity of more than 1500, suggesting that the membranes had a very narrow pore size distribution and an average pore diameter of approximately 3 Angstrom. The high temperature testing demonstrated that the incorporation of cobalt oxide into the silica matrix produced a structure with a higher thermal stability, able to resist thermally induced densification up to at least 600C. Furthermore, the membranes were tested for H2/CO2 binary feed mixtures between 400 and 600C. At these conditions, the reverse of the water gas shift reaction occurred, inadvertently generating CO and water which increased as a function of CO2 feed concentration. The purity of H2 in the permeate stream significantly decreased for CO2 feed concentrations in excess of 50 vol%. However, the gas mixtures (H2, CO2, CO and water) had a more profound effect on the H2 permeate flow rates which significantly decreased, almost exponentially as the CO2 feed concentration increased.

Fabrication and Characterization of Polyimide-CNTs hybrid membrane to enhance high performance CO2 separation

Directory of Open Access Journals (Sweden)

Tutuk Djoko Kusworo

2015-03-01

Full Text Available This study investigates the CO2 separation performance of a hybrid membranes flat sheet based on polyimide incorporated with carbon nanotubes (CNTs particles. CNTs was selected and its loading were a 1 wt% in total solid. The hybrid composite membranes were fabricated in order to increase their separation performance for the gaseous mixture of CO2 and CH4. Hybrid Composite  membrane incorporated carbon nanotubes were mannufactured  by the dry-wet phase inversion technique using flat sheet membrane casting machine system,  in which the CNTs were embedded into the polyimide membrane and the resulting membranes were characterized. The results from the FESEM, DSC and FTIR analysis confirmed that chemical modification on carbon nanotubes surface had taken place. Sieve-in-a-cage’ morphology observed shows the poor adhesion between polymer and unmodified CNT. The results revealed that the good multi-wall carbon nanotubes dispersion leads to enhanced gas permeation properties. It is also concluded that addition of carbon nanotubes particles into the matrix of Polyimide polymer has significant effect on the membrane structure and properties.

CO2 Capture Project-An Integrated, Collaborative Technology Development Project for Next Generation CO2 Separation, Capture and Geologic Sequestration

Energy Technology Data Exchange (ETDEWEB)

Helen Kerr; Linda M. Curran

2005-04-15

The CO{sub 2} Capture Project (CCP) was a joint industry project, funded by eight energy companies (BP, ChevronTexaco, EnCana, ENI, Norsk Hydro, Shell, Statoil, and Suncor) and three government agencies (European Union [DG RES & DG TREN], the Norwegian Research Council [Klimatek Program] and the U.S. Department of Energy [NETL]). The project objective was to develop new technologies that could reduce the cost of CO{sub 2} capture and geologic storage by 50% for retrofit to existing plants and 75% for new-build plants. Technologies were to be developed to ''proof of concept'' stage by the end of 2003. Certain promising technology areas were increased in scope and the studies extended through 2004. The project budget was approximately $26.4 million over 4 years and the work program is divided into eight major activity areas: Baseline Design and Cost Estimation--defined the uncontrolled emissions from each facility and estimate the cost of abatement in $/tonne CO{sub 2}. Capture Technology, Post Combustion: technologies, which can remove CO{sub 2} from exhaust gases after combustion. Capture Technology, Oxyfuel: where oxygen is separated from the air and then burned with hydrocarbons to produce an exhaust with high CO{sub 2} for storage. Capture Technology, Pre-Combustion: in which, natural gas and petroleum cokes are converted to hydrogen and CO{sub 2} in a reformer/gasifier. Common Economic Model/Technology Screening: analysis and evaluation of each technology applied to the scenarios to provide meaningful and consistent comparison. New Technology Cost Estimation: on a consistent basis with the baseline above, to demonstrate cost reductions. Geologic Storage, Monitoring and Verification (SMV): providing assurance that CO{sub 2} can be safely stored in geologic formations over the long term. Non-Technical: project management, communication of results and a review of current policies and incentives governing CO{sub 2} capture and storage. Pre

Study on CO2/ N2 separation: the effect of rubbery polymer coating on PVDF membrane

Science.gov (United States)

Zuwairi, M. Z.; Rahman, S. A.

2017-06-01

The emission of harmful gases such as carbon dioxide (CO2) via gas processing plant and daily human activities gave negative impacts to the environment and global inhabitant. Flat sheet asymmetric membranes were produced from homogenous solution of Poly(vinylideneflouride) (PVDF) via phase inversion method using N-methyl-2-pyrrolidone (NMP) as the solvent. While the poly ether b-amide (PEBAX) was dissolve by using of (70 ethanol and 30 water) as a solvent and and lithium chloride as a additives. The morphology and cross section of the produced membranes were observed by Scanning Electron Microscope (SEM). Then, the membranes were tested for chemical analysis to define the presence of PEBAX in the membrane by using Fourier Transform Infrared (FTIR) spectroscopy. The permeation performances of the membranes were evaluated in terms of permeability and selectivity of the membranes by using gas permeation test. Increasing the PEBAX content significantly increased the selectivity of the PVDF membrane to separate the CO2/N2 gases but decreased the amount of the gases that passed through the membrane.

Studies on CO2 removal and reduction. CO2 taisaku kenkyu no genjo

Energy Technology Data Exchange (ETDEWEB)

Shindo, Y [National Institute of Materials and Chemical Research, Tsukuba (Japan)

1993-02-01

This paper summarizes study trends mainly in CO2 fixing processes. Underground CO2 storage is a most promising method because it can fix a huge amount of CO2 and has low effects on ecological systems. Storing CO2 in ocean includes such methods as storing it in deep oceans; storing it in deep ocean beds; dissolving it into sea water; neutralizing it with calcium carbonates; and precipitating it as dry ice. Japan, disposing CO2 in these ways, may create international problems. Separation of CO2 may use a chemical absorption process as a superior method. Other processes discussed include a physical adsorption method and a membrane separation method. A useful method for CO2 fixation using marine organisms is fixation using coral reefs. This process will require an overall study including circulation of phosphorus and nitrogen. Marine organisms may include planktons and algae. CO2 fixation using land plants may be able to fix one trillion and 8 hundred billion tons of CO2 as converted to carbon. This process would require forest protection, prevention of desertification, and tree planting. Discussions are being given also on improving power generation cycles, recovering CO2 from automotive exhausts, and backfilling carbons into ground by means of photosynthesis. 23 refs., 7 figs., 1 tab.

Pulsed CO laser for isotope separation of uranium

Energy Technology Data Exchange (ETDEWEB)

Baranov, Igor Y.; Koptev, Andrey V. [Rocket-Space Technics Department, Baltic State Technical University, 1, 1st Krasnoarmeyskaya st.,St. Petersburg, 190005 (Russian Federation)

2012-07-30

This article proposes a technical solution for using a CO laser facility for the industrial separation of uranium used in the production of fuel for nuclear power plants, employing a method of laser isotope separation of uranium with condensation repression in a free jet. The laser operation with nanosecond pulse irradiation can provide an acceptable efficiency in the separating unit and a high efficiency of the laser with the wavelength of 5.3 {mu}m. In the present work we also introduce a calculation model and define the parameters of a mode-locked CO laser with a RF discharge in the supersonic stream. The average pulsed CO laser power of 3 kW is sufficient for efficient industrial isotope separation of uranium in one stage.

In-line formation of chemically cross-linked P84® co-polyimide hollow fibre membranes for H2/CO2 separation

KAUST Repository

Choi, Seung Hak; Jansen, Johannes C.; Tasselli, Franco; Barbieri, Giuseppe; Drioli, Enrico

2010-01-01

In this study, chemically cross-linked asymmetric P84® co-polyimide hollow fibre membranes with enhanced separation performance were fabricated, using a dry-wet spinning process with an innovative in-line cross-linking step. The chemical

CO2 Capture and Separation Properties in the Ionic Liquid 1-n-Butyl-3-Methylimidazolium Nonafluorobutylsulfonate

Directory of Open Access Journals (Sweden)

Lingyun Zhou

2014-05-01

Full Text Available Recently, the use of ionic liquids (ILs for carbon capture and separation processes has gained great interest by many researchers due to the high solubility of CO2 in ILs. In the present work, solubility measurements of CO2 in the novel IL 1-n-butyl-3-methylimidazolium nonafluorobutylsulfonate [C4mim][CF3CF2CF2CF2SO3] were performed with a high-pressure view-cell technique in the temperature range from 293.15 to 343.15 K and pressures up to about 4.2 MPa. For comparison, solubilities of H2, N2, and O2 in the IL were also measured at 323.15 K via the same procedure. The Krichevsky-Kasarnovsky equation was employed to correlate the measured solubility data. Henry’s law constants, enthalpies, and entropies of absorption for CO2 in the IL were also determined and presented. The CO2 solubility in this IL was compared with other ILs sharing the same cation. It was shown that the solubility of CO2 in these ILs follows the sequence: [C4mim][CF3CF2CF2CF2SO3] ≈ [C4mim][Tf2N] > [C4mim][CF3CF2CF2COO] > [C4mim][BF4], and the solubility selectivity of CO2 relative to O2, N2, and H2 in [C4mim][CF3CF2CF2CF2SO3] was 8, 16, and 22, respectively. Furthermore, this IL is regenerable and exhibits good stability. Therefore, the IL reported here would be a promising sorbent for CO2.

Silicon isotope separation utilizing infrared multiphoton dissociation of Si2F6 irradiated with two-color CO2 laser light

International Nuclear Information System (INIS)

Yokoyama, Atsushi; Ohba, Hironori; Hashimoto, Masashi; Arai, Shigeyoshi

2002-01-01

Silicon isotope separation has been done by utilizing the Infrared Multiphoton Dissociation (IRMPD) of Si 2 F 6 irradiated with two-color CO 2 laser lights. The two-color excitation method improved the separation efficiency keeping the high enrichment factors. For example, 99.74% of 28 Si was obtained at 49.63% dissociation of Si 2 F 6 after the simultaneous irradiation of 200 pulses with 966.23 cm -1 photons (0.084 J/cm 2 ) and 954.55 cm -1 photons (0.658 J/cm 2 ), while 2000 pulses were needed to obtain 99.35% of 28 Si at 35.6% dissociation in the case of only one-color irradiation at 954.55 cm -1 (0.97 J/cm 2 ). (author)

6 belysninger af vejledning

DEFF Research Database (Denmark)

Toft, Helle Mary; Jessing, Carla Tønder; Nymann, Anette

Artiklerne belyser vejledning af unge og vejledning af voksne. I relation til unge drejer det sig om: 1. vejledning af unge med vanskeligheder i forhold til uddannelse - her unge med særlige vejledningsbehov, og mentorordninger for unge, og 2. vejledning af unge i ungdomsuddannelser og i erhvervs...

Bestemmelse af spormetaller i organisk materiale

DEFF Research Database (Denmark)

Tjell, Jens Christian; Palfeldt, Kirsten

Behovet for pålidelige analysemetoder til bestemmelse af spormetalindhold i organiske materialer, f.eks. planter, slam og dyrevæv er stigende på grund af den stigende erkendelse af disse stoffers betydning for organismers fysiologi, både hvor disse stoffer optræder i uønskede koncentrationer som...... der over de sidste år udviklet en analyseprocedure hvorefter det er muligt at analysere for metallerne Mn, Cu, Ni, Co, Cr, Zn, Cd og Pb i planter, dyrevæv, jord, slam og andre materialer med standardafvigelser på mellem 5 og 10%. Der gøres rede for denne metode....

Final Report for Fractionation and Separation of Polydisperse Nanoparticles into Distinct Monodisperse Fractions Using CO2 Expanded Liquids

Energy Technology Data Exchange (ETDEWEB)

Chistopher Roberts

2007-08-31

The overall objective of this project was to facilitate efficient fractionation and separation of polydisperse metal nanoparticle populations into distinct monodisperse fractions using the tunable solvent properties of gas expanded liquids. Specifically, the dispersibility of ligand-stabilized nanoparticles in an organic solution was controlled by altering the ligand-solvent interaction (solvation) by the addition of carbon dioxide (CO{sub 2}) gas as an antisolvent (thereby tailoring the bulk solvent strength) in a custom high pressure apparatus developed in our lab. This was accomplished by adjusting the CO{sub 2} pressure over the liquid dispersion, resulting in a simple means of tuning the nanoparticle precipitation by size. Overall, this work utilized the highly tunable solvent properties of organic/CO{sub 2} solvent mixtures to selectively size-separate dispersions of polydisperse nanoparticles (ranging from 1 to 20 nm in size) into monodisperse fractions ({+-}1nm). Specifically, three primary tasks were performed to meet the overall objective. Task 1 involved the investigation of the effects of various operating parameters (such as temperature, pressure, ligand length and ligand type) on the efficiency of separation and fractionation of Ag nanoparticles. In addition, a thermodynamic interaction energy model was developed to predict the dispersibility of different sized nanoparticles in the gas expanded liquids at various conditions. Task 2 involved the extension of the experimental procedures identified in task 1 to the separation of other metal particles used in catalysis such as Au as well as other materials such as semiconductor particles (e.g. CdSe). Task 3 involved using the optimal conditions identified in tasks 1 and 2 to scale up the process to handle sample sizes of greater than 1 g. An experimental system was designed to allow nanoparticles of increasingly smaller sizes to be precipitated sequentially in a vertical series of high pressure vessels by

Topological ferrimagnetic behaviours of coordination polymers containing manganese(II) chains with mixed azide and carboxylate bridges and alternating F/AF/AF'/AF'/AF interactions.

Science.gov (United States)

Wang, Yan-Qin; Liu, Hou-Ting; Qi, Yan; Gao, En-Qing

2014-08-21

Two Mn(ii) complexes with azide and a new zwitterionic tetracarboxylate ligand 1,2,4,5-tetrakis(4-carboxylatopyridinium-1-methylene)benzene (L(1)), {[Mn5(L(1))2(N3)8(OH)2]·12H2O}n () and {[Mn5(L(1))2(N3)8(H2O)2](ClO4)2·6H2O}n (), have been synthesized and characterized crystallographically and magnetically. and contain similar alternating chains constructed by azide and carboxylate bridges. The independent sets of bridges alternate in an ABCCB sequence between adjacent Mn(ii) ions: (EO-N3)2 double bridges (EO = end-on) (denoted as A), [(EO-N3)(OCO)2] triple bridges (denoted as B) and [(EO-N3)(OCO)] double bridges (denoted as C). The alternating chains are interlinked into 2D coordination networks by the tetrapyridinium spacers. Magnetic studies demonstrate that the magnetic coupling through the double EO azide bridges is ferromagnetic and that through mixed azide/carboxylate bridges is antiferromagnetic. The unprecedented F/AF/AF'/AF'/AF coupling sequence along the chain dictates an uncompensated ground spin state (S = 5/2 per Mn5 unit) and leads to one-dimensional topological ferrimagnetism, which features a minimum in the χT versus T plot.

Differential modulation of plant immune responses by diverse members of the Pseudomonas savastanoi pv. savastanoi HopAF type III effector family.

Science.gov (United States)

Castañeda-Ojeda, M Pilar; López-Solanilla, Emilia; Ramos, Cayo

2017-06-01

The Pseudomonas savastanoi pv. savastanoi NCPPB 3335 type III secretion system (T3SS) effector repertoire includes 33 candidates, seven of which translocate into host cells and interfere with plant defences. The present study was performed to investigate the co-existence of both plasmid- and chromosomal-encoded members of the HopAF effector family, HopAF1-1 and HopAF1-2, respectively, in the genome of NCPPB 3335. Here, we show that the HopAF1 paralogues are widely distributed in the Pseudomonas syringae complex, where HopAF1-1 is most similar to the homologues encoded by other P. syringae pathovars infecting woody hosts that belong to phylogroups 1 and 3. We show that the expression of both HopAF1-1 and HopAF-2 is transcriptionally dependent on HrpL and demonstrate their delivery into Nicotiana tabacum leaves. Although the heterologous delivery of either HopAF1-1 or HopAF1-2 significantly suppressed the production of defence-associated reactive oxygen species levels, only HopAF1-2 reduced the levels of callose deposition. Moreover, the expression of HopAF1-2 by functionally effectorless P. syringae pv. tomato DC3000D28E completely inhibited the hypersensitive response in tobacco and significantly increased the competitiveness of the strain in Nicotiana benthamiana. Despite their functional differences, subcellular localization studies reveal that green fluorescent protein (GFP) fusions to either HopAF1-1 or HopAF1-2 are targeted to the plasma membrane when they are expressed in plant cells, a process that is completely dependent on the integrity of their N-myristoylation motif. Our results further support the notion that highly similar T3SS effectors might differentially interact with diverse plant targets, even when they co-localize in the same cell compartment. © 2016 BSPP AND JOHN WILEY & SONS LTD.

Anvendelse af MIP ved kildekarakterisering og vurdering af nedbrydning af chlorerede opløsningsmidler

DEFF Research Database (Denmark)

Broholm, Mette Martina; Janniche, Gry Sander; Damgaard, Ida

2014-01-01

Membrane Interface Probing (MIP) er et 'direct push' screeningsværktøj, som kan anvendes ved karakterisering af forurenede grunde. Karakterisering af kildeområder med chlorerede opløsningsmidler (som DNAPL) udgør et vigtigt led i udviklingen af den konceptuelle forståelse, som er essentiel...... for risikovurdering og valg af afværgestrategi. Integreret karakterisering med en række metoder for direkte såvel som indirekte dokumentation af DNAPL i moræneler, herunder MIP, er beskrevet i Kerrn-Jespersen et al. (2013). Det samlede DNAPL-karakteriseringsprojekt er beskrevet i detaljer i Janniche et al. (2013). En...... vurdering af anvendte detektorer for MIP er foretaget af Olsson (2013). Ved karakterisering af forurening med bl.a. chlorerede opløsningsmidler er der behov for en vurdering af forureningssammensætning og nedbrydning. Tilsvarende vurdering er nødvendig, når udviklingen af stimuleret reduktiv dechlorering...

Study on the dual-synthetic antiferromagnetic property using the Co2FeAl Heulser electrodes

International Nuclear Information System (INIS)

Zhang, D L; Xu, X G; Wu, Y; Li, X Q; Miao, J; Jiang, Y

2011-01-01

In this paper, we present the experimental results of dual-synthetic antiferromagnets (DSyAFs) with Co 2 FeAl (CFA) Heusler electrodes. It is shown that when the thicknesses of Ru layers are (0.45, 0.65) and (0.45, 1.00) (in nm), the CFA-based DSyAFs have a strong synthetic antiferromagnetic coupling among three CFA layers at room temperature, with a large saturation magnetic field Hs of ∼11000 Oe, a low saturation magnetization Ms of ∼708 emu/cm 3 and a switching field Hsw of ∼2.0 Oe, respectively. It is exciting that the CFA-based DSyAFs have an excellent thermal stability up to 400 0 C. Therefore, the CFA-based DSyAFs are favourable for applications in future spintronic devices.

Highly porous ionic rht metal-organic framework for H2 and CO2 storage and separation: A molecular simulation study

KAUST Repository

Babarao, Ravichandar

2010-07-06

The storage and separation of H2 and CO2 are investigated in a highly porous ionic rht metal-organic framework (rht-MOF) using molecular simulation. The rht-MOF possesses a cationic framework and charge-balancing extraframework NO3 - ions. Three types of unique open cages exist in the framework: rhombicuboctahedral, tetrahedral, and cuboctahedral cages. The NO3 - ions exhibit small mobility and are located at the windows connecting the tetrahedral and cuboctahedral cages. At low pressures, H2 adsorption occurs near the NO 3 - ions that act as preferential sites. With increasing pressure, H2 molecules occupy the tetrahedral and cuboctahedral cages and the intersection regions. The predicted isotherm of H2 at 77 K agrees well with the experimental data. The H2 capacity is estimated to be 2.4 wt % at 1 bar and 6.2 wt % at 50 bar, among the highest in reported MOFs. In a four-component mixture (15:75:5:5 CO2/H 2/CO/CH4) representing a typical effluent gas of H 2 production, the selectivity of CO2/H2 in rht-MOF decreases slightly with increasing pressure, then increases because of cooperative interactions, and finally decreases as a consequence of entropy effect. By comparing three ionic MOFs (rht-MOF, soc-MOF, and rho-ZMOF), we find that the selectivity increases with increasing charge density or decreasing free volume. In the presence of a trace amount of H2O, the interactions between CO2 and NO3 - ions are significantly shielded by H2O; consequently, the selectivity of CO 2/H2 decreases substantially. © 2010 American Chemical Society.

Co-crystallization as a separation technology: controlling product concentrations by co-crystals

NARCIS (Netherlands)

Urbanus, J.; Roelands, C.P.M.; Verdoes, D.; Jansens, P.J.; Horst, J.H. ter

2010-01-01

Co-crystallization is known as a product formulation technology, but it can also be used as a tool to solve crystallization problems. Product removal by co-crystallization in fermentations is used as a showcase to demonstrate the potential of co-crystallization as a separation technique. In

Polymer-silica hybrids for separation of CO2 and catalysis of organic reactions

Science.gov (United States)

Silva Mojica, Ernesto

Porous materials comprising polymeric and inorganic segments have attracted interest from the scientific community due to their unique properties and functionalities. The physical and chemical characteristics of these materials can be effectively exploited for adsorption applications. This dissertation covers the experimental techniques for fabrication of poly(vinyl alcohol) (PVA) and silica (SiO2) porous supports, and their functionalization with polyamines for developing adsorbents with potential applications in separation of CO2 and catalysis of organic reactions. The supports were synthesized by processes involving (i) covalent cross-linking of PVA, (ii) hydrolysis and poly-condensation of silica precursors (i,e,. sol-gel synthesis), and formation of porous structures via (iii) direct templating and (iv) phase inversion techniques. Their physical structure was controlled by the proper combination of the preparation procedures, which resulted in micro-structured porous materials in the form of micro-particles, membranes, and pellets. Their adsorption characteristics were tailored by functionalization with polyethyleneimine (PEI), and their physicochemical properties were characterized by vibrational spectroscopy (FTIR, UV-vis), microscopy (SEM), calorimetry (TGA, DSC), and adsorption techniques (BET, step-switch adsorption). Spectroscopic investigations of the interfacial cross-linking reactions of PEI and PVA with glutaraldehyde (GA) revealed that PEI catalyzes the cross-linking reactions of PVA in absence of external acid catalysts. In-situ IR spectroscopy coupled with a focal plane array (FPA) image detector allowed the characterization of a gradient interface on a PEI/PVA composite membrane and the investigation of the cross-linking reactions as a function of time and position. The results served as a basis to postulate possible intermediates, and propose the reaction mechanisms. The formulation of amine-functionalized CO2 capture sorbents was based on the

Performance test of PSA-type O{sub 2} separator for efficient O{sub 2} supply to room ventilation system combined with CO{sub 2} adsorption module

Energy Technology Data Exchange (ETDEWEB)

Han, Gi Bo; Jang, Jung Hee; Choi, Changsik [Institute for Advanced Engineering, Yongin (Korea, Republic of); Lee, Tae Jin [School of Chemical Engineering Yeungnam University, Gyeongsan (Korea, Republic of)

2016-04-15

High purity O{sub 2} concentrated by the PSA-type O{sub 2} separator was applied to a room ventilation system combined with CO{sub 2} adsorption module to remove the indoor CO{sub 2} for the indoor air quality. And then the room was occupied by several persons to breathe for the O{sub 2} consumption and CO{sub 2} generation. As a result, the indoor air quality was improved by the ventilation system combined with the O{sub 2} supply and the CO{sub 2} adsorption module. It was due to the fact that the CO{sub 2} concentration was not steeply increased, but also even decreased and then the increasing rate of the O{sub 2} concentration with the O{sub 2} supply was simultaneously increased by the CO{sub 2} removal despite the CO{sub 2} generation and O{sub 2} consumption with the four persons' breathing. As a representative result, in the case of supplying the high purity O{sub 2} of 30 L/min under using the CO{sub 2} adsorption module, the best performance with the highest increasing rate of O{sub 2} concentration and the lowest increasing rate of CO{sub 2} concentration was obtained among the various cases, and then the increasing rates of CO{sub 2} radiation and O{sub 2} concentration were -2.3 ppm/min and 33.3%/min, respectively.

An energetic analysis of CO2 capture on a gas turbine combining flue gas recirculation and membrane separation

International Nuclear Information System (INIS)

Belaissaoui, Bouchra; Cabot, Gilles; Cabot, Marie-Sophie; Willson, David; Favre, Eric

2012-01-01

Post-combustion Carbon Capture and Storage (CCS) is currently intensively investigated as a key issue for the mitigation of greenhouse gases emissions. A very large number of studies is dedicated to coal power plants. In this paper, the possibility to achieve carbon capture on a gas turbine, based on a combination of flue gas recycle and membrane separation is reported. Membrane processes are effectively known to offer attractive performances in terms of energy efficiency, as soon as concentrated and/or pressure mixtures have to be treated. Two different flow schemes have been simulated and compared: flue gas recycle with air combustion and flue gas recycle with an oxygen enriched feed mixture. The energy requirement of the different processes, expressed in GJ (thermal basis) per ton of recovered CO 2 , and the size of the membrane capture process (expressed in m 2 of membrane area) have been systematically estimated for different membrane separation performances. It is shown that an overall energy requirement down to 2.6 GJ per ton can possibly be achieved when optimal operating conditions, based on oxygen enriched air (OEA) combustion together with a highly selective membrane (CO 2 /N 2 selectivity of 200) are combined. Additional possibilities in order to minimise the energy penalty of the process are discussed. -- Highlights: ► A carbon capture process for gas turbine has been investigated for the first time, with membrane separation unit. ► Air combustion systematically induces CO 2 capture specific energy requirement far above alternative capture processes. ► Remarkably, a very low energy requirement can be achieved (down to 2.6 GJ/ton) with Oxygen Enriched Air combustion. ► Target membrane selectivities and optimal oxygen content for combustion have been identified.

Logning af teledata i lyset af Tele2-dommen

DEFF Research Database (Denmark)

Lentz, Lene Wacher

2017-01-01

De danske teleudbydere har siden 2007 været underlagt en pligt efter logningsbekendtgørelsen til at registrere data om al telekommunikation for at sikre at data er tilgængelige ved en eventuel senere efterforskning. Logningspligten må nu revideres og i vidt omfang afvikles som følge af EU-domstol...

CO2 Acquisition Membrane (CAM)

Science.gov (United States)

Mason, Larry W.; Way, J. Douglas; Vlasse, Marcus

2003-01-01

The objective of CAM is to develop, test, and analyze thin film membrane materials for separation and purification of carbon dioxide (CO2) from mixtures of gases, such as those found in the Martian atmosphere. The membranes are targeted toward In Situ Resource Utilization (ISRU) applications that will operate in extraterrestrial environments and support future unmanned and human space missions. A primary application is the Sabatier Electrolysis process that uses Mars atmosphere CO2 as raw material for producing water, oxygen, and methane for rocket fuel and habitat support. Other applications include use as an inlet filter to collect and concentrate Mars atmospheric argon and nitrogen gases for habitat pressurization, and to remove CO2 from breathing gases in Closed Environment Life Support Systems (CELSS). CAM membrane materials include crystalline faujasite (FAU) zeolite and rubbery polymers such as silicone rubber (PDMS) that have been shown in the literature and via molecular simulation to favor adsorption and permeation of CO2 over nitrogen and argon. Pure gas permeation tests using commercial PDMS membranes have shown that both CO2 permeance and the separation factor relative to other gases increase as the temperature decreases, and low (Delta)P(Sub CO2) favors higher separation factors. The ideal CO2/N2 separation factor increases from 7.5 to 17.5 as temperature decreases from 22 C to -30 C. For gas mixtures containing CO2, N2, and Ar, plasticization decreased the separation factors from 4.5 to 6 over the same temperature range. We currently synthesize and test our own Na(+) FAU zeolite membranes using standard formulations and secondary growth methods on porous alumina. Preliminary tests with a Na(+) FAU membrane at 22 C show a He/SF6 ideal separation factor of 62, exceeding the Knudsen diffusion selectivity by an order of magnitude. This shows that the membrane is relatively free from large defects and associated non-selective (viscous flow) transport

The declining uptake rate of atmospheric CO2 by land and ocean sinks

International Nuclear Information System (INIS)

Raupach, M.R.; Gloor, M.; Sarmiento, J.L.; Gasser, T.

2014-01-01

Through 1959-2012, an airborne fraction (AF) of 0.44 of total anthropogenic CO 2 emissions remained in the atmosphere, with the rest being taken up by land and ocean CO 2 sinks. Understanding of this uptake is critical because it greatly alleviates the emissions reductions required for climate mitigation, and also reduces the risks and damages that adaptation has to embrace. An observable quantity that reflects sink properties more directly than the AF is the CO 2 sink rate (k S ), the combined land-ocean CO 2 sink flux per unit excess atmospheric CO 2 above pre industrial levels. Here we show from observations that k S declined over 1959-2012 by a factor of about 1/3, implying that CO 2 sinks increased more slowly than excess CO 2 . Using a carbon-climate model, we attribute the decline in k S to four mechanisms: slower-than-exponential CO 2 emissions growth (35% of the trend), volcanic eruptions (25 %), sink responses to climate change (20 %), and nonlinear responses to increasing CO 2 , mainly oceanic (20 %). The first of these mechanisms is associated purely with the trajectory of extrinsic forcing, and the last two with intrinsic, feedback responses of sink processes to changes in climate and atmospheric CO 2 . Our results suggest that the effects of these intrinsic, nonlinear responses are already detectable in the global carbon cycle. Although continuing future decreases in k S will occur under all plausible CO 2 emission scenarios, the rate of decline varies between scenarios in non intuitive ways because extrinsic and intrinsic mechanisms respond in opposite ways to changes in emissions: extrinsic mechanisms cause k S to decline more strongly with increasing mitigation, while intrinsic mechanisms cause k S to decline more strongly under high-emission, low-mitigation scenarios as the carbon-climate system is perturbed further from a near-linear regime. (authors)

A new metal-organic framework for separation of C2H2/CH4 and CO2/CH4 at room temperature

Science.gov (United States)

Duan, Xing; Zhou, You; Lv, Ran; Yu, Ben; Chen, Haodong; Ji, Zhenguo; Cui, Yuanjing; Yang, Yu; Qian, Guodong

2018-04-01

A 3D microporous metal-organic framework with open Cu2+ sites and suitable pore space, [Cu2(L)(H2O)2]·(H2O)4(DMF)8 (ZJU-15, H4L = 5,5‧-(9H-carbazole-2,7-diyl)diisophthalic acid; DMF = N,N-dimethylformamide; ZJU = Zhejiang University), has been constructed and characterized. The activated ZJU-15a has three different types of cages and exhibits BET surface area of 1660 m2 g-1, and can separate gas mixture of C2H2/CH4 and CO2/CH4 at room temperature.

AfAP2-1, An Age-Dependent Gene of Aechmea fasciata, Responds to Exogenous Ethylene Treatment

Directory of Open Access Journals (Sweden)

Ming Lei

2016-02-01

Full Text Available The Bromeliaceae family is one of the most morphologically diverse families with a pantropical distribution. To schedule an appropriate flowering time for bromeliads, ethylene is commonly used to initiate flower development in adult plants. However, the mechanism by which ethylene induces flowering in adult bromeliads remains unknown. Here, we identified an APETALA2 (AP2-like gene, AfAP2-1, in Aechmea fasciata. AfAP2-1 contains two AP2 domains and is a nuclear-localized protein. It functions as a transcriptional activator, and the activation domain is located in the C-terminal region. The expression level of AfAP2-1 is higher in juvenile plants than in adult plants, and the AfAP2-1 transcript level was rapidly and transiently reduced in plants treated with exogenous ethylene. Overexpression of AfAP2-1 in Arabidopsis thaliana results in an extremely delayed flowering phenotype. These results suggested that AfAP2-1 responds to ethylene and is a putative age-dependent flowering regulator in A. fasciata.

The Changing Landscape for Stroke Prevention in AF: Findings From the GLORIA-AF Registry Phase 2

NARCIS (Netherlands)

Huisman, M.V.; Rothman, K.J.; Paquette, M.; Teutsch, C.; Diener, H.C.; Dubner, S.J.; Halperin, J.L.; Ma, C.S.; Zint, K.; Elsaesser, A.; Bartels, D.B.; Lip, G.Y.; Hemels, M.E.; et al.,

2017-01-01

BACKGROUND: GLORIA-AF (Global Registry on Long-Term Oral Antithrombotic Treatment in Patients with Atrial Fibrillation) is a prospective, global registry program describing antithrombotic treatment patterns in patients with newly diagnosed nonvalvular atrial fibrillation at risk of stroke. Phase 2

Contributions to accelerating atmospheric CO2 growth from economic activity, carbon intensity, and efficiency of natural sinks

International Nuclear Information System (INIS)

Canadella, J.G.; Raupacha, M.R.; Le Quere, C.; Buitenhuis, E.T.; Gillett, N.P.; Field, C.B.; Ciais, P.; Conway, T.J.; Houghton, R.A.; Marland, G.

2007-01-01

The growth rate of atmospheric carbon dioxide (CO2), the largest human contributor to human-induced climate change, is increasing rapidly. Three processes contribute to this rapid increase. Two of these processes concern emissions. Recent growth of the world economy combined with an increase in its carbon intensity have led to rapid growth in fossil fuel CO2 emissions since 2000: comparing the 1990s with 2000-2006, the emissions growth rate increased from 1.3% to 3.3%/y. The third process is indicated by increasing evidence (P 0.89) for a long-term (50-year) increase in the airborne fraction (AF) of CO2 emissions, implying a decline in the efficiency of CO2 sinks on land and oceans in absorbing anthropogenic emissions. Since 2000, the contributions of these three factors to the increase in the atmospheric CO2 growth rate have been ∼65 ± 16% from increasing global economic activity, 17 ± 6% from the increasing carbon intensity of the global economy, and 18 ± 15% from the increase in AF. An increasing AF is consistent with results of climate-carbon cycle models, but the magnitude of the observed signal appears larger than that estimated by models. All of these changes characterize a carbon cycle that is generating stronger-than-expected and sooner-than-expected climate forcing. airborne fraction anthropogenic carbon emissions carbon-climate feedback terrestrial and ocean carbon emissions vulnerabilities of the carbon cycle

CO2-afgifter: Beskeden regning til den energi-intensive industri

DEFF Research Database (Denmark)

Andersen, Mikael Skou

2008-01-01

De store energi-intensive virksomheder i Europa har fordel af vidtrækkende undtagelser for de CO2- og energiafgifter som medlemslandene har indført. Bekymring for konkurrence-evnen har som regel været baggrunden for at give en særlig rabat til de største udledere. Størrelsen af rabatten og dermed...... den egentlige klima-regning til virksomhederne er imidlertid vanskelig at gennemskue. Med slutrapporten fra det store EU-projekt COMETR er det nu blevet muligt både at sætte tal på de reelle afgifter og at vurdere betydningen for konkurrence-evnen for erhvervene....

Carbon-14 exchange between CO2 and CO in the system 14CO2-CO-NOsub(x)(Ar, N2, O2)-quartz vessels

International Nuclear Information System (INIS)

Wawer, A.; Zielinski, M.

1981-01-01

It has been established that the rate of 14 C exchange between CO 2 and CO is diminished in presence of NO and NO 2 . The temperature dependence of the overall rate of exchange and the partial orders in respect to separate components of the exchange mixtures have been determined. The rate dependence on quartz surface has been established and the surface mechanism considered. The inhibiting action NO and NO 2 is explained. At higher pressures the catalytic effect of NO was found and explained. (author)

Unconventional magnetic phase separation in γ -CoV2O6

Science.gov (United States)

Shen, L.; Jellyman, E.; Forgan, E. M.; Blackburn, E.; Laver, M.; Canévet, E.; Schefer, J.; He, Z.; Itoh, M.

2017-08-01

We have explored the magnetism in the nongeometrically frustrated spin-chain system γ -CoV2O6 which possesses a complex magnetic exchange network. Our neutron diffraction patterns at low temperatures (T ≤TN=6.6 K) are best described by a model in which two magnetic phases coexist in a volume ratio 65(1) : 35(1), with each phase consisting of a single spin modulation. This model fits previous studies and our observations better than the model proposed by Lenertz et al. [J. Phys. Chem. C 118, 13981 (2014), 10.1021/jp503389c], which consisted of one phase with two spin modulations. By decreasing the temperature from TN, the minority phase of our model undergoes an incommensurate-commensurate lock-in transition at T*=5.6 K. Based on these results, we propose that phase separation is an alternative approach for degeneracy-lifting in frustrated magnets.

Innovative CO{sub 2} separation of biogas by polymer resins: operation of a continuous lab-scale plant

Energy Technology Data Exchange (ETDEWEB)

Raab, Katharina; Lamprecht, Martina; Brechtel, Kevin; Scheffknecht, Guenter

2012-06-15

Upgrading biogas allows for the injection of biomethane into the natural gas grid and thus a decentralized use. Since the currently available techniques have a high energy demand, there is a high potential to improve biogas upgrading. Innovative CO{sub 2} separation of biogas by the use of polymer resins can reduce the energy demand, the capital expenditure, and the operational costs. In this study, we show the ability of polymer resin to selectively adsorb CO{sub 2}. Desorption tests showed the potential for continuous use of the resin. In a continuous lab-scale plant, numerous variations of process parameters were carried out and optimization possibilities were demonstrated. Methane purity up to 98% was achieved. The favorable estimated energy demand indicates the great potential of the demonstrated improved process. (copyright 2012 WILEY-VCH Verlag GmbH 8 Co. KGaA, Weinheim)

Køb af B2B serviceydelser

DEFF Research Database (Denmark)

Grünbaum, Niels Nolsøe; Hollensen, Svend; Andresen, Marc

2011-01-01

I den tidlige B-t-B-købsadfærdslitteratur har man lagt megen vægt på, at købsadfærden i forbindelse med B-t-B-serviceydelser er meget rationel præget. Gennem en større eksplorativ undersøgelse af danske virksomheders indkøb af konsulentydelser inden for hr, har forfatterne fået indblik i de fakto...

Direct visualization of phase separation between superconducting and nematic domains in Co-doped CaFe2As2 close to a first-order phase transition

Science.gov (United States)

Fente, Antón; Correa-Orellana, Alexandre; Böhmer, Anna E.; Kreyssig, Andreas; Ran, S.; Bud'ko, Sergey L.; Canfield, Paul C.; Mompean, Federico J.; García-Hernández, Mar; Munuera, Carmen; Guillamón, Isabel; Suderow, Hermann

2018-01-01

We show that biaxial strain induces alternating tetragonal superconducting and orthorhombic nematic domains in Co-substituted CaFe2As2 . We use atomic force, magnetic force, and scanning tunneling microscopy to identify the domains and characterize their properties, finding in particular that tetragonal superconducting domains are very elongated, more than several tens of micrometers long and about 30 nm wide; have the same Tc as unstrained samples; and hold vortices in a magnetic field. Thus, biaxial strain produces a phase-separated state, where each phase is equivalent to what is found on either side of the first-order phase transition between antiferromagnetic orthorhombic and superconducting tetragonal phases found in unstrained samples when changing Co concentration. Having such alternating superconducting domains separated by normal conducting domains with sizes of the order of the coherence length opens opportunities to build Josephson junction networks or vortex pinning arrays and suggests that first-order quantum phase transitions lead to nanometric-size phase separation under the influence of strain.

CO2 emission factors for waste incineration: Influence from source separation of recyclable materials

DEFF Research Database (Denmark)

Larsen, Anna Warberg; Astrup, Thomas

2011-01-01

variations between emission factors for different incinerators, but the background for these variations has not been thoroughly examined. One important reason may be variations in collection of recyclable materials as source separation alters the composition of the residual waste incinerated. The objective...... routed to incineration. Emission factors ranged from 27 to 40kg CO2/GJ. The results appeared most sensitive towards variations in waste composition and water content. Recycling rates and lower heating values could not be used as simple indicators of the resulting emission factors for residual household...... different studies and when using the values for environmental assessment purposes....

Tværsektorielt samarbejde ved behandling af patienter med type 2-diabetes

DEFF Research Database (Denmark)

Munch, Lene; Røder, Michael E; Hansen, Ida H

2018-01-01

Hovedbudskaber • Sundhedsstyrelsen lægger vægt på tværsektorielt samarbejde omkring patienten med type 2-diabetes, men denne tankegang er dog ikke implementeret i det danske sundhedsvæsen • På organisatorisk niveau kan en stratificerings- og forløbsmodel give anvisninger til opgave- og...... udnyttelse af sundhedsvæsenets ressourcer samtidig med, at behandling af høj kvalitet fastholdes og udvikles for patienter med type 2-diabetes...

Documentation for calculating CO{sub 2} reduction costs of using bio diesel; Dokumentation for beregning af CO{sub 2}-reduktionsomkostningen ved anvendelse af biodiesel

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-01-01

In connection to the European Commission's proposal for a directive on the promotion of biofuels for transport and the new climate strategy for Denmark, the Danish Energy Authority has evaluated the potential for and economics of production of biodiesel in Denmark. This note is documentation for the Danish Energy Authority's socio-economic analysis regarding rape-based biodiesel. The analysis consists of two parts: 1. Costs of producing biodiesel, 2. Costs of cultivating rape. The main conclusion is that the socio-economic CO{sub 2} reduction costs of producing biodiesel in Denmark are subject to some uncertainty. The uncertainty is primarily linked to difficulty in determining central parameters, e.g. stating the socio-economic costs of producing rape-seed, including stating prices of production factors and by-products. (ba)

Dual-Channel, Molecular-Sieving Core/Shell ZIF@MOF Architectures as Engineered Fillers in Hybrid Membranes for Highly Selective CO2 Separation.

Science.gov (United States)

Song, Zhuonan; Qiu, Fen; Zaia, Edmond W; Wang, Zhongying; Kunz, Martin; Guo, Jinghua; Brady, Michael; Mi, Baoxia; Urban, Jeffrey J

2017-11-08

A novel core/shell porous crystalline structure was prepared using a large pore metal organic framework (MOF, UiO-66-NH 2 , pore size, ∼ 0.6 nm) as core surrounded by a small pore zeolitic imidazolate framework (ZIF, ZIF-8, pore size, ∼ 0.4 nm) through a layer-by-layer deposition method and subsequently used as an engineered filler to construct hybrid polysulfone (PSF) membranes for CO 2 capture. Compared to traditional fillers utilizing only one type of porous material with rigid channels (either large or small), our custom designed core/shell fillers possess clear advantages via pore engineering: the large internal channels of the UiO-66-NH 2 MOFs create molecular highways to accelerate molecular transport through the membrane, while the thin shells with small pores (ZIF-8) or even smaller pores generated at the interface by the imperfect registry between the overlapping pores of ZIF and MOF enhance molecular sieving thus serving to distinguish slightly larger N 2 molecules (kinetic diameter, 0.364 nm) from smaller CO 2 molecules (kinetic diameter, 0.33 nm). The resultant core/shell ZIF@MOF and as-prepared hybrid PSF membranes were characterized by transmission electron microscopy, X-ray diffraction, wide-angle X-ray scattering, scanning electron microscopy, Fourier transform infrared, thermogravimetric analysis, differential scanning calorimetry, and contact angle tests. The dependence of the separation performance of the membranes on the MOF/ZIF ratio was also studied by varying the number of layers of ZIF coatings. The integrated PSF-ZIF@MOF hybrid membrane (40 wt % loading) with optimized ZIF coating cycles showed improved hydrophobicity and excellent CO 2 separation performance by simultaneously increasing CO 2 permeability (CO 2 permeability of 45.2 barrer, 710% higher than PSF membrane) and CO 2 /N 2 selectivity (CO 2 /N 2 selectivity of 39, 50% higher than PSF membrane), which is superior to most reported hybrid PSF membranes. The strategy of using

Process for analyzing CO{sub 2} in seawater

Science.gov (United States)

Atwater, J.E.; Akse, J.R.; DeHart, J.

1997-07-01

The process of this invention comprises providing a membrane for separating CO{sub 2} into a first CO{sub 2} sample phase and a second CO{sub 2} analyte phase. CO{sub 2} is then transported through the membrane thereby separating the CO{sub 2} with the membrane into a first CO{sub 2} sample phase and a second CO{sub 2} analyte liquid phase including an ionized, conductive, dissociated CO{sub 2} species. Next, the concentration of the ionized, conductive, dissociated CO{sub 2} species in the second CO{sub 2} analyte liquid phase is chemically amplified using a water-soluble chemical reagent which reversibly reacts with undissociated CO{sub 2} to produce conductivity changes therein corresponding to fluctuations in the partial pressure of CO{sub 2} in the first CO{sub 2} sample phase. Finally, the chemically amplified, ionized, conductive, dissociated CO{sub 2} species is introduced to a conductivity measuring instrument. Conductivity changes in the chemically amplified, ionized, conductive, dissociated CO{sub 2} species are detected using the conductivity measuring instrument. 43 figs.

Process for analyzing CO.sub.2 in seawater

Science.gov (United States)

Atwater, James E.; Akse, James R.; DeHart, Jeffrey

1997-01-01

The process of this invention comprises providing a membrane for separating CO.sub.2 into a first CO.sub.2 sample phase and a second CO.sub.2 analyte phase. CO.sub.2 is then transported through the membrane thereby separating the CO.sub.2 with the membrane into a first CO.sub.2 sample phase and a second CO.sub.2 analyte liquid phase including an ionized, conductive, dissociated CO.sub.2 species. Next, the concentration of the ionized, conductive, dissociated CO.sub.2 species in the second CO.sub.2 analyte liquid phase is chemically amplified using a water-soluble chemical reagent which reversibly reacts with undissociated CO.sub.2 to produce conductivity changes therein corresponding to fluctuations in the partial pressure of CO.sub.2 in the first CO.sub.2 sample phase. Finally, the chemically amplified, ionized, conductive, dissociated CO.sub.2 species is introduced to a conductivity measuring instrument. Conductivity changes in the chemically amplified, ionized, conductive, dissociated CO.sub.2 species are detected using the conductivity measuring instrument.

Lyden af musik - er lyden af idealisme

DEFF Research Database (Denmark)

Eigtved, Michael

2015-01-01

Programartiklen til Det Ny Teaters opsætning af Rodgers & Hammersteins The Sound of Music, undersøger musicalgenrens - og især de konkrete ophavsmænds- affinitet til fremstillingen af såvel idealistiske som ideologiske universer.......Programartiklen til Det Ny Teaters opsætning af Rodgers & Hammersteins The Sound of Music, undersøger musicalgenrens - og især de konkrete ophavsmænds- affinitet til fremstillingen af såvel idealistiske som ideologiske universer....

CO2 capture by gas hydrate crystallization: Application on the CO2-N2 mixture

International Nuclear Information System (INIS)

Bouchemoua, A.

2012-01-01

CO 2 capture and sequestration represent a major industrial and scientific challenge of this century. There are different methods of CO 2 separation and capture, such as solid adsorption, amines adsorption and cryogenic fractionation. Although these processes are well developed at industrial level, they are energy intensive. Hydrate formation method is a less energy intensive and has an interesting potential to separate carbon dioxide. Gas hydrates are Document crystalline compounds that consist of hydrogen bonded network of water molecules trapping a gas molecule. Gas hydrate formation is favored by high pressure and low temperature. This study was conducted as a part of the SECOHYA ANR Project. The objective is to study the thermodynamic and kinetic conditions of the process to capture CO 2 by gas hydrate crystallization. Firstly, we developed an experimental apparatus to carry out experiments to determine the thermodynamic and kinetic formation conditions of CO 2 -N 2 gas hydrate mixture in water as liquid phase. We showed that the operative pressure may be very important and the temperature very low. For the feasibility of the project, we used TBAB (Tetrabutylammonium Bromide) as thermodynamic additive in the liquid phase. The use of TBAB may reduce considerably the operative pressure. In the second part of this study, we presented a thermodynamic model, based on the van der Waals and Platteeuw model. This model allows the estimation of thermodynamic equilibrium conditions. Experimental equilibrium data of CO 2 -CH 4 and CO 2 -N 2 mixtures are presented and compared to theoretical results. (author)

Evaluering af ordning med psykologbehandling af personer med let til moderat depression

DEFF Research Database (Denmark)

Fjeldsted, Rita; Christensen, Kaj Sparle

Herværende rapport evaluerer den pr. 1.4.2008 indførte ordning med mulighed for henvisning til psykologbehandling med 60 % tilskud for patienter med let til moderat depression. Evalueringen har betjent sig af flere gensidigt supplerende metoder: spørgeskemaundersøgelser overfor patienter, psykolo......Herværende rapport evaluerer den pr. 1.4.2008 indførte ordning med mulighed for henvisning til psykologbehandling med 60 % tilskud for patienter med let til moderat depression. Evalueringen har betjent sig af flere gensidigt supplerende metoder: spørgeskemaundersøgelser overfor patienter...... tidligere evaluering af forsøgsordning af psykologbehandling af depression i perioden 2005-06. 18.419 personer i alderen 18-37 år blev henvist til psykolog i den undersøgte ordning i perioden 1.2.2009 – 31.1.2010, svarende til en henvisningshyppighed på 1,6 % af baggrundsbefolkningen i samme aldersgruppe....... Ordningen giver mulighed for én rehenvisning, og 9 % blev rehenvist i perioden. Spørgeskemaresultater viser, at kun 33 % af de henviste falder ind under henvisningskriteriet ” let til moderat depression” på tidspunktet for opstart af psykologbehandling, 39 % har ingen tegn på depression, og 28 % har svær...

Improved solar-driven photocatalytic performance of Ag{sub 2}CO{sub 3}/(BiO){sub 2}CO{sub 3} prepared in-situ

Energy Technology Data Exchange (ETDEWEB)

Zhong, Junbo, E-mail: junbozhong@163.com [Key Laboratory of Green Catalysis of Higher Education Institutes of Sichuan, College of Chemistry and Pharmaceutical Engineering, Sichuan University of Science and Engineering, Zigong 643000 (China); Li, Jianzhang, E-mail: lschmanuscript@163.com [Key Laboratory of Green Catalysis of Higher Education Institutes of Sichuan, College of Chemistry and Pharmaceutical Engineering, Sichuan University of Science and Engineering, Zigong 643000 (China); Huang, Shengtian; Cheng, Chaozhu; Yuan, Wei [Key Laboratory of Green Catalysis of Higher Education Institutes of Sichuan, College of Chemistry and Pharmaceutical Engineering, Sichuan University of Science and Engineering, Zigong 643000 (China); Li, Minjiao [Key Laboratory of Green Catalysis of Higher Education Institutes of Sichuan, College of Chemistry and Pharmaceutical Engineering, Sichuan University of Science and Engineering, Zigong 643000 (China); Sichuan Provincial Academician (Expert) Workstation, Sichuan University of Science and Engineering, Zigong 643000 (China); Ding, Jie [Key Laboratory of Green Catalysis of Higher Education Institutes of Sichuan, College of Chemistry and Pharmaceutical Engineering, Sichuan University of Science and Engineering, Zigong 643000 (China)

2016-05-15

Highlights: • Ag{sub 2}CO{sub 3}/(BiO){sub 2}CO{sub 3} photocatalysts were prepared in-situ. • The photo-induced charge separation rate has been greatly increased. • The photocatalytic activity has been greatly promoted. - Abstract: Ag{sub 2}CO{sub 3}/(BiO){sub 2}CO{sub 3} composites have been fabricated in-situ via a facile parallel flaw co-precipitation method. The specific surface area, structure, morphology, and the separation rate of photo-induced charge pairs of the photocatalysts were characterized by Brunauer–Emmett–Teller (BET) method, X-ray diffraction (XRD), UV–vis diffuse reflectance spectroscopy(DRS), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and surface photovoltage (SPV) spectroscopy, respectively. XRD patterns and DRS demonstrated that Ag{sub 2}CO{sub 3} has no effect on the crystal phase and bandgap of (BiO){sub 2}CO{sub 3}. The existence of Ag{sub 2}CO{sub 3} in the composites enhances the separation rate of photo-induced charge pairs of the photocatalysts. The photocatalytic performance of Ag{sub 2}CO{sub 3}/(BiO){sub 2}CO{sub 3} was evaluated by the decolorization of methyl orange (MO) aqueous solution under simulated solar irradiation. It was found that the simulated solar-induced photocatalytic activity of Ag{sub 2}CO{sub 3}/(BiO){sub 2}CO{sub 3} copmposites was significantly improved, which was mainly attributed to the enhanced surface area and the separation rate of photo-induced charge pairs.

Pure- and mixed-gas CO2/CH4 separation properties of PIM-1 and an amidoxime-functionalized PIM-1

KAUST Repository

Swaidan, Raja

2014-05-01

The prototypical solution-processable polymer of intrinsic microporosity, PIM-1, and derivatives thereof offer combinations of permeability and selectivity that make them potential candidate materials for membrane-based gas separations. Paramount to the design and evaluation of PIMs for economical natural gas sweetening is a high and stable CO2/CH4 selectivity under realistic, mixed-gas conditions. Here, amidoxime-functionalized PIM-1 (AO-PIM-1) was prepared and examined for fundamental structure/property relationships. Qualitative NLDFT pore-size distribution analyses of physisorption isotherms (N2 at -196 oC; CO2 at 0 oC) reveal a tightened microstructure indicating size-sieving ultra-microporosity (<7Å). AO-PIM-1 demonstrated a three-fold increase in αD(CO2/CH4) over PIM-1, surpassing the 2008 upper bound with P(CO2)=1153Barrer and ideal α(CO2/CH4)=34. Under a 50:50 CO2:CH4 mixed-gas feed, AO-PIM-1 showed less selectivity loss than PIM-1, maintaining a mixed-gas α(CO2/CH4) ~21 across a 20bar pressure range. Conversely, PIM-1 endured up to 60% increases in mixed-gas CH4 permeability over pure-gas values concurrent with a selectivity of only ~8 at 20bar. A pervasive intermolecular hydrogen bonding network in AO-PIM-1 predominantly yields a rigidified microstructure that mitigates CO2-induced matrix dilations, reducing detrimental mixed-gas CH4 copermeation. © 2014 Elsevier B.V.

The declining uptake rate of atmospheric CO2 by land and ocean sinks

Directory of Open Access Journals (Sweden)

M. R. Raupach

2014-07-01

Full Text Available Through 1959–2012, an airborne fraction (AF of 0.44 of total anthropogenic CO2 emissions remained in the atmosphere, with the rest being taken up by land and ocean CO2 sinks. Understanding of this uptake is critical because it greatly alleviates the emissions reductions required for climate mitigation, and also reduces the risks and damages that adaptation has to embrace. An observable quantity that reflects sink properties more directly than the AF is the CO2 sink rate (kS, the combined land–ocean CO2 sink flux per unit excess atmospheric CO2 above preindustrial levels. Here we show from observations that kS declined over 1959–2012 by a factor of about 1 / 3, implying that CO2 sinks increased more slowly than excess CO2. Using a carbon–climate model, we attribute the decline in kS to four mechanisms: slower-than-exponential CO2 emissions growth (~ 35% of the trend, volcanic eruptions (~ 25%, sink responses to climate change (~ 20%, and nonlinear responses to increasing CO2, mainly oceanic (~ 20%. The first of these mechanisms is associated purely with the trajectory of extrinsic forcing, and the last two with intrinsic, feedback responses of sink processes to changes in climate and atmospheric CO2. Our results suggest that the effects of these intrinsic, nonlinear responses are already detectable in the global carbon cycle. Although continuing future decreases in kS will occur under all plausible CO2 emission scenarios, the rate of decline varies between scenarios in non-intuitive ways because extrinsic and intrinsic mechanisms respond in opposite ways to changes in emissions: extrinsic mechanisms cause kS to decline more strongly with increasing mitigation, while intrinsic mechanisms cause kS to decline more strongly under high-emission, low-mitigation scenarios as the carbon–climate system is perturbed further from a near-linear regime.

Innovative CO{sub 2} separation process for biogas upgrading using polymeric resins; Innovatives CO{sub 2}-Abscheideverfahren zur Biogasaufbereitung mit Hilfe von Polymerharzen

Energy Technology Data Exchange (ETDEWEB)

Harrivelle, Carole; Safai, Daniel; Raab, Katharina; Klein, Barbara [Stuttgart Univ. (Germany). Abt. Brennstoffe und Rauchgasreinigung; Scheffknecht, Guenter

2016-08-01

Upgraded biogas can be injected into the natural gas grid. The Institute of Combustion and Power Plant Technology (IFK) is investigating several innovative biogas upgrading processes with the aim to develop treatment methods adapted for small biogas plants. This paper presents a process to separate CO{sub 2} from CH{sub 4} by concentration swig adsorption using an amine functionalized polymer resin. The experiments were carried out at a continuous laboratory scale plant. The results are compared with previous experiments from earlier work at the IFK. The new resin shows a significant increase of working capacity and CH{sub 4} purity as well as a decrease of CH{sub 4} loss.

Enhancing visible light photocatalytic and photocharge separation of (BiO){sub 2}CO{sub 3} plate via dramatic I{sup −} ions doping effect

Energy Technology Data Exchange (ETDEWEB)

Liang, Lei [College of Chemistry and Materials Science, Huaibei Normal University, Huaibei, 235000, Anhui (China); Cao, Jing [College of Chemistry and Materials Science, Huaibei Normal University, Huaibei, 235000, Anhui (China); Anhui Collaborative Innovation Center of Advanced Functional Composite, Huaibei, 235000, Anhui (China); Lin, Haili, E-mail: linhaili@mail.ipc.ac.cn [College of Chemistry and Materials Science, Huaibei Normal University, Huaibei, 235000, Anhui (China); Guo, Xiaomin; Zhang, Meiyu [College of Chemistry and Materials Science, Huaibei Normal University, Huaibei, 235000, Anhui (China); Chen, Shifu, E-mail: chshifu@chnu.edu.cn [College of Chemistry and Materials Science, Huaibei Normal University, Huaibei, 235000, Anhui (China); College of Chemistry and Materials Engineering, Anhui Science and Technology University, Fengyang, 233100, Anhui (China)

2016-08-15

Highlights: • Novel I-(BiO){sub 2}CO{sub 3} was prepared by a facile chemical precipitation method. • I{sup −} ions impurity level located on the top of valence band of (BiO){sub 2}CO{sub 3}. • I{sup −} ions doping largely improved photocatalytic activity of I-(BiO){sub 2}CO{sub 3}. • I-(BiO){sub 2}CO{sub 3} displayed excellent photocharge separation efficiency. - Abstract: Novel I{sup −} ions doped (BiO){sub 2}CO{sub 3} (I-(BiO){sub 2}CO{sub 3}) photocatalysts were successfully synthesized via a facile chemical precipitation method. Under visible light (λ > 400 nm), I-(BiO){sub 2}CO{sub 3} displayed much higher activity for rhodamine B and dichlorophenol degradation than the undoped (BiO){sub 2}CO{sub 3}. The pseudo-first-order rate constant k{sub app} of RhB degradation over 15.0% I-(BiO){sub 2}CO{sub 3} was 0.54 h{sup −1}, which is 11.3 times higher than that of (BiO){sub 2}CO{sub 3}. The doped I{sup −} ions formed an impurity level on the top of valence band of (BiO){sub 2}CO{sub 3} and induced much more visible light to be absorbed. The enhanced photocurrent and surface photovoltage properties were detected, which strongly ensures the efficient separation of electrons and holes in I-(BiO){sub 2}CO{sub 3} system under visible light. It provides a facile way to improve the photocatalytic activity of the wide-band-gap (BiO){sub 2}CO{sub 3} via intense doping effect of I{sup −} ions.

Effective Approach for Increasing the Heteroatom Doping Levels of Porous Carbons for Superior CO2 Capture and Separation Performance.

Science.gov (United States)

Abdelmoaty, Yomna H; Tessema, Tsemre-Dingel; Norouzi, Nazgol; El-Kadri, Oussama M; Turner, Joseph B McGee; El-Kaderi, Hani M

2017-10-18

Development of efficient sorbents for carbon dioxide (CO 2 ) capture from flue gas or its removal from natural gas and landfill gas is very important for environmental protection. A new series of heteroatom-doped porous carbon was synthesized directly from pyrazole/KOH by thermolysis. The resulting pyrazole-derived carbons (PYDCs) are highly doped with nitrogen (14.9-15.5 wt %) as a result of the high nitrogen-to-carbon ratio in pyrazole (43 wt %) and also have a high oxygen content (16.4-18.4 wt %). PYDCs have a high surface area (SA BET = 1266-2013 m 2 g -1 ), high CO 2 Q st (33.2-37.1 kJ mol -1 ), and a combination of mesoporous and microporous pores. PYDCs exhibit significantly high CO 2 uptakes that reach 2.15 and 6.06 mmol g -1 at 0.15 and 1 bar, respectively, at 298 K. At 273 K, the CO 2 uptake improves to 3.7 and 8.59 mmol g -1 at 0.15 and 1 bar, respectively. The reported porous carbons also show significantly high adsorption selectivity for CO 2 /N 2 (128) and CO 2 /CH 4 (13.4) according to ideal adsorbed solution theory calculations at 298 K. Gas breakthrough studies of CO 2 /N 2 (10:90) at 298 K showed that PYDCs display excellent separation properties. The ability to tailor the physical properties of PYDCs as well as their chemical composition provides an effective strategy for designing efficient CO 2 sorbents.

EXPERIMENTAL DESIGN AND RESPONSE SURFACE MODELING OF PI/PES-ZEOLITE 4A MIXED MATRIX MEMBRANE FOR CO2 SEPARATION

Directory of Open Access Journals (Sweden)

T. D. KUSWORO

2015-09-01

Full Text Available This paper investigates the effect of preparation of polyimide/polyethersulfone (PI/PES blending-zeolite mixed matrix membrane through the manipulation of membrane production variables such as polymer concentration, blending composition and zeolite loading. Combination of central composite design and response surface methodology were applied to determine the main effect and interaction effects of these variables on membrane separation performance. The quadratic models between each response and the independent parameters were developed and the response surface models were tested with analysis of variance (ANOVA. In this study, PI/ (PES–zeolite 4A mixed matrix membranes were casted using dry/wet phase inversion technique. The separation performance of mixed matrix membrane had been tested using pure gases such as CO2 and CH4. The results showed that zeolite loading was the most significant variable that influenced the CO2/CH4 selectivity among three variables and the experimental results were in good agreement with those predicted by the proposed regression models. The gas separation performance of the membrane was relatively higher as compare to polymeric membrane. Therefore, combination of central composite design and response surface methodology can be used to prepare optimal condition for mixed matrix membrane fabrication. The incorporation of 20 wt% zeolite 4A into 25 wt% of PI/PES matrix had resulted in a high separation performance of membrane material.

CO2 adsorption using TiO2 composite polymeric membranes: A kinetic study.

Science.gov (United States)

Hafeez, Sarah; Fan, X; Hussain, Arshad; Martín, C F

2015-09-01

CO2 is the main greenhouse gas which causes global climatic changes on larger scale. Many techniques have been utilised to capture CO2. Membrane gas separation is a fast growing CO2 capture technique, particularly gas separation by composite membranes. The separation of CO2 by a membrane is not just a process to physically sieve out of CO2 through the controlled membrane pore size. It mainly depends upon diffusion and solubility of gases, particularly for composite dense membranes. The blended components in composite membranes have a high capability to adsorb CO2. The adsorption kinetics of the gases may directly affect diffusion and solubility. In this study, we have investigated the adsorption behaviour of CO2 in pure and composite membranes to explore the complete understanding of diffusion and solubility of CO2 through membranes. Pure cellulose acetate (CA) and cellulose acetate-titania nanoparticle (CA-TiO2) composite membranes were fabricated and characterised using SEM and FTIR analysis. The results indicated that the blended CA-TiO2 membrane adsorbed more quantity of CO2 gas as compared to pure CA membrane. The high CO2 adsorption capacity may enhance the diffusion and solubility of CO2 in the CA-TiO2 composite membrane, which results in a better CO2 separation. The experimental data was modelled by Pseudo first-order, pseudo second order and intra particle diffusion models. According to correlation factor R(2), the Pseudo second order model was fitted well with experimental data. The intra particle diffusion model revealed that adsorption in dense membranes was not solely consisting of intra particle diffusion. Copyright © 2015. Published by Elsevier B.V.

Sustainable synthesis of magnetically separable SiO2/Co@Fe2O4 nanocomposite and its catalytic applications for the benzimidazole synthesis

Science.gov (United States)

Jithendra Kumara, K. S.; Krishnamurthy, G.; Sunil Kumar, N.; Naik, Nagaraja; Praveen, T. M.

2018-04-01

The Co(II) and Fe(III) centres magnetically separable two new mesoporous nanocatalyst were synthesised via chemical synthesis method. The transmission electron microscopic studies (TEM) show that, the particles are spherical shape with mean size of 20 nm. The Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) reveals that SiO2 is coating on the surface of the cobalt ferrate nanoparticle (CoFe2O4). The SiO2 coating is efficiently preventing the aggregated collision of nanoparticles. Magnetic measurements show that diamagnetic character of the SiO2 is unaffected to the coercivity of SiO2 coated CoFe2O4 particles. In addition, these nanoparticles are used as nanocatalyst for high yielding, facile and expeditious synthesis of various functionalized 2-arylbenzimidazoles via one-pot condensation. The cascade including imine formation, cyclization, condensation, and aromatization occurs, without addition of any reducing or oxidizing agents. In all situations, the desired product was synthesised with excellent yield. The shorter reaction time, mild reaction condition, simplicity, non-toxicity, safe reaction and easy workup are the impotent merits of this protocol.

Mikroplastik i sediment fra de danske farvande - og betydningen af de biogeokemiske sedimentkarakterer

DEFF Research Database (Denmark)

Strand, Jakob; Lassen, Pia; Shashoua, Yvonne

mm), og biogeokemiske faktorer som indholdet af organisk carbon (TOC) og indholdet af fine partikler (... phthalater og nonylphenol. Dette skyldes nok mest co-variationer i forhold til kildeeksponering og biogeokemiske faktorer som TOC....

Natural separation of the acyl-CoA ligase reaction results in a non-adenylating enzyme.

Science.gov (United States)

Wang, Nan; Rudolf, Jeffrey D; Dong, Liao-Bin; Osipiuk, Jerzy; Hatzos-Skintges, Catherine; Endres, Michael; Chang, Chin-Yuan; Babnigg, Gyorgy; Joachimiak, Andrzej; Phillips, George N; Shen, Ben

2018-06-04

Acyl-coenzyme A (CoA) ligases catalyze the activation of carboxylic acids via a two-step reaction of adenylation followed by thioesterification. Here, we report the discovery of a non-adenylating acyl-CoA ligase PtmA2 and the functional separation of an acyl-CoA ligase reaction. Both PtmA1 and PtmA2, two acyl-CoA ligases from the biosynthetic pathway of platensimycin and platencin, are necessary for the two steps of CoA activation. Gene inactivation of ptmA1 and ptmA2 resulted in the accumulation of free acid and adenylate intermediates, respectively. Enzymatic and structural characterization of PtmA2 confirmed its ability to only catalyze thioesterification. Structural characterization of PtmA2 revealed it binds both free acid and adenylate substrates and undergoes the established mechanism of domain alternation. Finally, site-directed mutagenesis restored both the adenylation and complete CoA activation reactions. This study challenges the currently accepted paradigm of adenylating enzymes and inspires future investigations on functionally separated acyl-CoA ligases and their ramifications in biology.

En genlæsning af John Rawls i lyset af hans diskussion af forholdet til fremtidige generationer

DEFF Research Database (Denmark)

Lübcke, Poul

2009-01-01

På grundlag af en konsekventialistisk rekonstruktion af Rawls' politiske position gøres der rede for Rawls eksplicitte og implicitte vurdering af vores ansvar over for fremtidige generationer......På grundlag af en konsekventialistisk rekonstruktion af Rawls' politiske position gøres der rede for Rawls eksplicitte og implicitte vurdering af vores ansvar over for fremtidige generationer...

In vivo binding, pharmacokinetics and metabolism of the selective M2 muscarinic antagonists [3H]AF-DX 116 and [3H]AF-DX 384 in the anesthetized rat

International Nuclear Information System (INIS)

Mickala, Patrick; Boutin, Herve; Bellanger, Cecile; Chevalier, Cyril; MacKenzie, Eric T.; Dauphin, Francois

1996-01-01

The pharmacokinetics, in vivo binding and metabolism of two M 2 muscarinic receptor antagonists, [ 3 H]AF-DX 116 and [ 3 H]AF-DX 384, were studied in anesthetized rats, which received either the tracer alone or following a saturating injection of atropine. Both radioligands were cleared from the circulation with distribution half-lives of 17 and 14 sec and elimination half-lives of 17 and 40 min for [ 3 H]AF-DX 116 and [ 3 H]AF-DX 384, respectively. A radioactive distribution, predominant in peripheral organs when compared to brain, was found at each time studied after tracer injection. Atropine-displaceable tracer uptake was evidenced at 20-40 min in brain (31%), submandibular glands (26%), spleen (37%) and notably heart (55%) for [ 3 H]AF-DX 116 but only in heart (50%) for [ 3 H]AF-DX 384 at 10-20 min. Regional brain sampling revealed a relatively uniform distribution of [ 3 H]AF-DX 384 and a -45% atropine saturation effect (i.e., specific binding) in the thalamus 20 min after injection. Sequential thin-layer chromatographic studies performed on tissue extracts demonstrated the rapid appearance of labeled metabolites of both radiotracers in brain (but less so in liver) and especially in cardiac tissues, where almost 70% of total radioactivity still corresponded to authentic tracer 40 min after injection. Thus, based on their low blood-brain barrier permeability and the high presence of labeled metabolites in the central nervous system, AF-DX 116 and AF-DX 384 might be more helpful in the study of M 2 muscarinic receptors present in heart rather than brain. Labeled with positron emittors, these M 2 antagonists might be applicable to the pathophysiological study of disease states, such as cardiomyopathies

Energirenovering af parcelhuse

DEFF Research Database (Denmark)

Aggerholm, Søren

af de tre huse består i efterisolering af lofter op til 300 mm, udskiftning af almindelige termoruder til energiruder, og installation af solvarmeanlæg til produktion af varmt brugsvand. I de tre huse er der ved energirenoveringen opnået en reduktion af energiforbruget på 16-22 procent. Rapporten...

Kortlægning af evalueringer og undersøgelser af vejledning knyttet til vejledning af unge i UU-regi

DEFF Research Database (Denmark)

Skovhus, Randi Boelskifte; thomsen, rie

2013-01-01

Kortlægning af evalueringer og undersøgelser af vejledning knyttet til vejledning af unge i UU-regi 2004-2013. Et arbejdspapir......Kortlægning af evalueringer og undersøgelser af vejledning knyttet til vejledning af unge i UU-regi 2004-2013. Et arbejdspapir...

Fremtidssikring af kloaknet

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place

2008-01-01

Beskrivelse af hvordan man ved udbygning af eksisterende kloaknet og ved nytænkning af planlægning af nye bydele kan sikre sig langsigtet mod konsekvenserne af klimaændinger og kraftigere nedbør...

Adsorption and separation of CO{sub 2} on Fe(II)-MOF-74: Effect of the open metal coordination site

Energy Technology Data Exchange (ETDEWEB)

Lou, Wolong; Yang, Jiangfeng; Li, Libo; Li, Jinping, E-mail: Jpli211@hotmail.com

2014-05-01

We describe the successful synthesis of Fe{sub 2}(dobdc) (dobdc{sup 4−}=2, 5-dioxido-1, 4-benzenedicarboxylate), which has an open metal coordination site Fe(II), and investigate the adsorption properties of three important molecules CO{sub 2}, CH{sub 4} and N{sub 2} on Fe{sub 2}(dobdc) and an oxidized analog, Fe{sub 2}(O{sub 2})(dobdc). We found that CO{sub 2} adsorption isotherm of Fe{sub 2}(dobdc) at 10 bar was very different from Fe{sub 2}(O{sub 2})(dobdc), with the capacities of 144.5 cm{sup 3} g{sup −1} and 98.1 cm{sup 3} g{sup −1}, respectively. The adsorption capacities for CH{sub 4} were 75.8 cm{sup 3} g{sup −1} and 36.8 cm{sup 3} g{sup −1}, respectively, at 10 bar in these materials. Using ideal adsorbed solution theory (IAST), we obtain the adsorption selectivity for CO{sub 2} using equimolar mixtures of CO{sub 2}/CH{sub 4} and CO{sub 2}/N{sub 2} with Fe{sub 2}(dobdc) and Fe{sub 2}(O{sub 2})(dobdc) as a function of pressure. Fe{sub 2}(dobdc) has a higher, more stable separation factor. - Graphical abstract: The selectivity of CO{sub 2}/CH{sub 4} mixture (50%/50%) on Fe{sub 2}(dobdc) and Fe{sub 2}(O{sub 2})(dobdc). - Highlights: • We explored the contrastive adsorption of CO{sub 2}, CH{sub 4}, and N{sub 2} in Fe{sub 2}(dobdc) and Fe{sub 2}(O{sub 2})(dobdc) for the first time. • Through IAST, we obtain the adsorption selectivity for CO{sub 2} from the equimolar mixture of CO{sub 2}/CH{sub 4} and CO{sub 2}/N{sub 2} for Fe{sub 2}(dobdc) and Fe{sub 2}(O{sub 2})(dobdc). • We determined that the open coordination site of Fe(II) is the main reason for different adsorption performances.

Web 2.0 - Lær dog af Obama!

DEFF Research Database (Denmark)

Ivang, Reimer

2009-01-01

At Obama vandt 2008 præsidentvalget ved at anvende web 2.0 teknologier, er ingen hemmelighed. Men hvordan gjorde han det? Og hvorfor var det så effektfuldt? Dette blogindlæg ser Obama efter i kortene, og kortlægger den læring, som danske virksomheder kan høste af den fantastiske strategi, Obama-k...

Silicon isotope separation utilizing infrared multiphoton dissociation of Si{sub 2}F{sub 6} irradiated with two-color CO{sub 2} laser light

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, Atsushi; Ohba, Hironori; Hashimoto, Masashi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Ishii, Takeshi; Ohya, Akio [Nuclear Development Corp., Tokai, Ibaraki (Japan); Arai, Shigeyoshi [Hill Research Co. Ltd., Tokyo (Japan)

2002-08-01

Silicon isotope separation has been done by utilizing the Infrared Multiphoton Dissociation (IRMPD) of Si{sub 2}F{sub 6} irradiated with two-color CO{sub 2} laser lights. The two-color excitation method improved the separation efficiency keeping the high enrichment factors. For example, 99.74% of {sup 28}Si was obtained at 49.63% dissociation of Si{sub 2}F{sub 6} after the simultaneous irradiation of 200 pulses with 966.23 cm{sup -1} photons (0.084 J/cm{sup 2}) and 954.55 cm{sup -1} photons (0.658 J/cm{sup 2}), while 2000 pulses were needed to obtain 99.35% of {sup 28}Si at 35.6% dissociation in the case of only one-color irradiation at 954.55 cm{sup -1} (0.97 J/cm{sup 2}). (author)

Controlling Cooperative CO2 Adsorption in Diamine-Appended Mg2(dobpdc) Metal-Organic Frameworks.

Science.gov (United States)

Siegelman, Rebecca L; McDonald, Thomas M; Gonzalez, Miguel I; Martell, Jeffrey D; Milner, Phillip J; Mason, Jarad A; Berger, Adam H; Bhown, Abhoyjit S; Long, Jeffrey R

2017-08-02

In the transition to a clean-energy future, CO 2 separations will play a critical role in mitigating current greenhouse gas emissions and facilitating conversion to cleaner-burning and renewable fuels. New materials with high selectivities for CO 2 adsorption, large CO 2 removal capacities, and low regeneration energies are needed to achieve these separations efficiently at scale. Here, we present a detailed investigation of nine diamine-appended variants of the metal-organic framework Mg 2 (dobpdc) (dobpdc 4- = 4,4'-dioxidobiphenyl-3,3'-dicarboxylate) that feature step-shaped CO 2 adsorption isotherms resulting from cooperative and reversible insertion of CO 2 into metal-amine bonds to form ammonium carbamate chains. Small modifications to the diamine structure are found to shift the threshold pressure for cooperative CO 2 adsorption by over 4 orders of magnitude at a given temperature, and the observed trends are rationalized on the basis of crystal structures of the isostructural zinc frameworks obtained from in situ single-crystal X-ray diffraction experiments. The structure-activity relationships derived from these results can be leveraged to tailor adsorbents to the conditions of a given CO 2 separation process. The unparalleled versatility of these materials, coupled with their high CO 2 capacities and low projected energy costs, highlights their potential as next-generation adsorbents for a wide array of CO 2 separations.

Polyacrylonitrile-Derived Sponge-Like Micro/Macroporous Carbon for Selective CO2 Separation.

Science.gov (United States)

Guo, Li-Ping; Hu, Qing-Tao; Zhang, Peng; Li, Wen-Cui; Lu, An-Hui

2018-03-25

CO 2 capture under a dynamical flow situation requires adsorbents possessing balanced proportion of macropores as diffusion path and micropores as adsorption reservoir. However, the construction of interconnected micro-/macropores structure coupled with abundant nitrogen species into one carbon skeleton remains a challenge. Here, we report a new approach to prepare sponge-like carbon with a well-developed micro-/macroporous structure and enriched nitrogen species through aqueous phase polymerization of acrylonitrile in the presence of graphene oxide. The tension stress caused by the uniform thermal shrinkage of polyacrylonitrile during the pyrolysis together with the favorable flexibility of graphene oxide sheets are responsible for the formation of the sponge-like morphology. The synergistic effect of micro-/macroporous framework and rich CO 2 -philic site enables such carbon to decrease resistance to mass transfer and show high CO 2 dynamic selectivity over N 2 (454) and CH 4 (11), as well as good CO 2 capacity at 298 K under low CO 2 partial pressure (0.17 bar, a typical CO 2 partial pressure in flue gas). The above attributes make this porous carbon a promising candidate for CO 2 capture from flue gas, methane sources and other relevant applications. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural Basis for Polypyrimidine Tract Recognition by the Essential Pre-mRNA Splicing Factor U2AF65

International Nuclear Information System (INIS)

Sickmier, E.; Frato, K.; Shen, H.; Paranawithana, S.; Green, M.; Kielkopf, C.

2006-01-01

The essential pre-mRNA splicing factor, U2AF 65 , guides the early stages of splice site choice by recognizing a polypyrimidine (Py)-tract consensus sequence near the 3'-splice site. Since Py-tracts are relatively poorly conserved in higher eukaryotes, U2AF 65 is faced with the problem of specifying uridine-rich sequences, yet tolerating a variety of nucleotide substitutions found in natural Py-tracts. To better understand these apparently contradictory RNA binding characteristics, the X-ray structure of the U2AF 65 RNA binding domain bound to a Py-tract composed of seven uridines has been determined at 2.5Angstroms resolution. Specific hydrogen bonds between U2AF 65 and the uracil bases provide an explanation for polyuridine recognition. Flexible sidechains and bound water molecules form the majority of the base contacts, and potentially could rearrange when the U2AF 65 structure adapts to different Py-tract sequences. The energetic importance of conserved residues for Py-tract binding is established by analysis of site-directed mutant U2AF 65 proteins using surface plasmon resonance

CO2 sorption of a ceramic separation membrane

NARCIS (Netherlands)

Wormeester, Herbert; Benes, Nieck Edwin; Spijksma, G.I.; Verweij, H.; Poelsema, Bene

2004-01-01

The ellipsometric characterization of the CO2 sorption of a silica membrane provides a fast and accurate technique for the characterization of maximum sorption and the heat of adsorption. Both parameters are evaluated for the 73 nm thick silica layer as well as the 1650 nm thick supporting γ-layer.

Physically Gelled Room-Temperature Ionic Liquid-Based Composite Membranes for CO2/N-2 Separation: Effect of Composition and Thickness on Membrane Properties and Performance

Energy Technology Data Exchange (ETDEWEB)

Nguyen, PT; Voss, BA; Wiesenauer, EF; Gin, DL; Nobe, RD

2013-07-03

An aspartame-based, low molecular-weight organic gelator (LMOG) was used to form melt-infused and composite membranes with two different imidazolium-based room-temperature ionic liquids (RTILs) for CO2 separation from N-2. Previous work demonstrated that LMOGs can gel RTILs at low, loading levels, and this aspartame-based LMOG was selected because it has been reported to gel a large number of RTILs. The imidazolium-based RTILs were used because of their inherent good properties for CO2/light gas separations. Analysis of the resulting bulk RTIL/LMOG physical gels showed that these materials have high sol-gel transition temperatures (ca. 135 degrees C) suitable for flue gas applications. Gas permeabilities and burst pressure measurements of thick, melt infused membranes revealed a trade-off between high CO2 permeabilities and good mechanical stability as a function of the LMOG loading. Defect-free, composite membranes of the gelled RTILs were successfully fabricated by choosing an appropriate porous membrane support (hydrophobic PTFE) using a suitable coating technique (roller coating). The thicknesses of the applied composite gel layers ranged from 10.3 to 20.7 mu m, which represents an order of magnitude decrease in active layer thickness, compared to the original melt-infused gel RTIL membranes.

Udlejers godkendelse af ny erhvervslejer

DEFF Research Database (Denmark)

Munk-Hansen, Carsten

2009-01-01

I artiklen er taget udgangspunkt i den »klassiske« afståelsessituation, hvor en lejer vil afhænde den i de lejede lokaler drevne virksomhed, og lejeren har afståelsesret til en af udlejer godkendt lejer, uden at kravene til den ny lejer er specificeret. På baggrund af Vestre Landsrets dom af 9/2 ...

Enhanced Gas Separation through Nanoconfined Ionic Liquid in Laminated MoS2 Membrane.

Science.gov (United States)

Chen, Danke; Ying, Wen; Guo, Yi; Ying, Yulong; Peng, Xinsheng

2017-12-20

Two-dimensional (2D) materials-based membranes show great potential for gas separation. Herein an ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF 4 ]), was confined in the 2D channels of MoS 2 -laminated membranes via an infiltration process. Compared with the corresponding bulk [BMIM][BF 4 ], nanoconfined [BMIM][BF 4 ] shows an obvious incremental increase in freezing point and a shift of vibration bands. The resulting MoS 2 -supported ionic liquid membrane (MoS 2 SILM) exhibits excellent CO 2 separation performance with high CO 2 permeance (47.88 GPU) and superb selectivity for CO 2 /N 2 (131.42), CO 2 /CH 4 (43.52), and CO 2 /H 2 (14.95), which is much better than that of neat [BMIM][BF 4 ] and [BMIM][BF 4 ]-based membranes. The outstanding performance of MoS 2 SILMs is attributed to the nanoconfined [BMIM][BF 4 ], which enables fast transport of CO 2 . Long-term operation also reveals the durability and stability of the prepared MoS 2 SILMs. The method of confining ILs in the 2D nanochannels of 2D materials may pave a new way for CO 2 capture and separation.

Separation of Co2+ present in aqueous solution on calcium carbonate

International Nuclear Information System (INIS)

Garcia A, E.; Granados C, F.

2008-01-01

The CaCO 3 was synthesized by precipitation method and characterized using SEM, EDS, TGA and IR. It was studied the adsorption behavior of Co 2+ present in aqueous solution on the synthesized material by experiments batch type at room temperature. Was found that removal of cobalt ions was greater than 40% indicating that this material can be used to remove Co 2+ present in aqueous solution. (Author)

Interplay between mesoscopic phase separation and bulk magnetism in the layered Na.sub.x./sub.CoO.sub.2./sub

Czech Academy of Sciences Publication Activity Database

Zorkovská, A.; Orendáč, M.; Šebek, Josef; Šantavá, Eva; Svoboda, P.; Bradaric, I.; Savič, I.; Feher, A.

2005-01-01

Roč. 72, č. 13 (2005), 132412/1-132412/4 ISSN 1098-0121 Institutional research plan: CEZ:AV0Z10100520 Keywords : Na x CoO 2 * mesoscopic phase separation * bulk magnetism Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.185, year: 2005

Nyttigt bidrag til professionalisering af revisionsudvalg

DEFF Research Database (Denmark)

Thomsen, Steen

2009-01-01

Anmeldelse af: KPMG. 2009, Audit Committee Institute. Revisionsudvalg i Praksis. 2. reviderede udgave.......Anmeldelse af: KPMG. 2009, Audit Committee Institute. Revisionsudvalg i Praksis. 2. reviderede udgave....

Betydningen af Lawsonia og PCV2 virus for daglig tilvækst hos slagtesvin

DEFF Research Database (Denmark)

Johansen, Markku; Nielsen, Mai Britt Friis; Dahl, Jan

Resultaterne af denne undersøgelse viser at: - Grise med store mængder Lawsonia i gødningen (≥106/gram gødning) har større risiko (OR=5,2) for at være en langsomt voksende gris. - Grise med synlige tarmforandringer har større risiko (OR=13,2) for at være en langsomt voksende gris. - Grise med...... diarré har større risiko (OR=10,1) for at være en langsomt voksende gris. Derimod kunne der ikke påvises nogen sammenhæng mellem mængden af PCV2 virus, antistoffer mod PCV2 virus eller påvisning af PCV2 virus ved immunhistokemi i tarmlymfeknude og tilvæksten hos grise. Undersøgelsen er gennemført i 5...... virus og Lawsonia på DTU-Veterinærinstitutet. For hver gris blev den maksimalt målte værdi af Lawsonia og PCV2 virus mængde i gødning og antistoffer mod de to sygdomme brugt som forklarende variabel. Sammenhængen til hurtigt/langsomt voksende grise for de maksimalt målte værdier blev undersøgt ved...

Hærdeteknologi og Holdbarhed af Betonkonstruktioner

DEFF Research Database (Denmark)

Sørensen, Eigil V.

Kurset Hærdeteknologi og Holdbarhed af Betonkonstruktioner afholdes i 1. og 2. periode af forårssemesteret 2006. Kurset sigter på at give de studerende en grundlæggende forståelse af, hvorledes man designer og udfører holdbare betonkonstruktioner....

Modified ZIF-8 mixed matrix membrane for CO2/CH4 separation

Science.gov (United States)

Nordin, Nik Abdul Hadi Md; Ismail, Ahmad Fauzi; Misdan, Nurasyikin; Nazri, Noor Aina Mohd

2017-10-01

Tunability of metal-organic frameworks (MOFs) properties enables them to be tailored for specific applications. In this study, zeolitic imidazole framework 8 (ZIF-8), sub-class of MOF, underwent pre-synthesis and post-synthesis modifications. The pre-synthesis modification using GO (ZIF-8/GO) shows slight decrease in textural properties, while the post-synthesis modification using amine solution (ZIF-8/NH2) resulted in superior BET surface area and pore volume. Mixed matrix membranes (MMMs) derived from polysulfone (PSf) and the modified ZIF-8s were then prepared via dry/wet phase inversion. The polymer chain flexibility of the resulted MMMs shows rigidification, where ZIF-8/NH2 as filler resulting higher rigidification compared to ZIF-8/GO. The MMMs were further subjected to pure CO2 and CH4 gas permeation experiments. The PSf/ZIF-8/NH2 shows superior CO2/CH4 selectivity (88% increased) while sacrificing CO2 permeance due to combination of severe polymer chain rigidification and the presence of CO2-philic group, amine. Whereas, the PSf/ZIF-8/GO possess 64% increase in CO2 permeance without notable changes in CO2/CH4 selectivity.

Gas permeation process for post combustion CO2 capture

International Nuclear Information System (INIS)

Pfister, Marc

2017-01-01

CO 2 Capture and Storage (CCS) is a promising solution to separate CO 2 from flue gas, to reduce the CO 2 emissions in the atmosphere, and hence to reduce global warming. In CCS, one important constraint is the high additional energy requirement of the different capture processes. That statement is partly explained by the low CO 2 fraction in the inlet flue gas and the high output targets in terms of CO 2 capture and purity (≥90%). Gas permeation across dense membrane can be used in post combustion CO 2 capture. Gas permeation in a dense membrane is ruled by a mass transfer mechanism and separation performance in a dense membrane are characterized by component's effective permeability and selectivity. One of the newest and encouraging type of membrane in terms of separation performance is the facilitated transport membrane. Each particular type of membrane is defined by a specific mass transfer law. The most important difference to the mass transfer behavior in a dense membrane is related to the facilitated transport mechanism and the solution diffusion mechanism and its restrictions and limitations. Permeation flux modelling across a dense membrane is required to perform a post combustion CO 2 capture process simulation. A CO 2 gas permeation separation process is composed of a two-steps membrane process, one drying step and a compression unit. Simulation on the energy requirement and surface area of the different membrane modules in the global system are useful to determine the benefits of using dense membranes in a post combustion CO 2 capture technology. (author)

C2A2 Project - CO2 Capture by Advances Amines process

International Nuclear Information System (INIS)

Thybaud, Nathalie

2014-06-01

This publication presents the operation principles and the obtained results for a research demonstrator developed in Le Havre by EDF and Alstom for CO 2 capture by post-combustion. The implemented technology, developed by Alstom and DOX Chemical is named Advanced Amines Processes (AAP). This process comprises the use of solvent and a specific process scheme (the Advanced Flow Scheme or AFS). The smoke treatment chain of the installation is described, and the valorisation of combustion by-products and of smoke processing operations is indicated. The capacities of the installation are given. Systems aimed at increasing the solvent lifetime are described, and some operational parameters are indicated. Various aspects related to the demonstrator design, construction and operation are discussed. Results obtained during tests between October 2013 and March 2014 are given and discussed in terms of quantity of captured CO 2 , of energy performance, of solvent management and consumption, of emissions, of corrosion, of exploitation organisation, and of instrumentation verification and data quality

Common data model for natural language processing based on two existing standard information models: CDA+GrAF.

Science.gov (United States)

Meystre, Stéphane M; Lee, Sanghoon; Jung, Chai Young; Chevrier, Raphaël D

2012-08-01

An increasing need for collaboration and resources sharing in the Natural Language Processing (NLP) research and development community motivates efforts to create and share a common data model and a common terminology for all information annotated and extracted from clinical text. We have combined two existing standards: the HL7 Clinical Document Architecture (CDA), and the ISO Graph Annotation Format (GrAF; in development), to develop such a data model entitled "CDA+GrAF". We experimented with several methods to combine these existing standards, and eventually selected a method wrapping separate CDA and GrAF parts in a common standoff annotation (i.e., separate from the annotated text) XML document. Two use cases, clinical document sections, and the 2010 i2b2/VA NLP Challenge (i.e., problems, tests, and treatments, with their assertions and relations), were used to create examples of such standoff annotation documents, and were successfully validated with the XML schemata provided with both standards. We developed a tool to automatically translate annotation documents from the 2010 i2b2/VA NLP Challenge format to GrAF, and automatically generated 50 annotation documents using this tool, all successfully validated. Finally, we adapted the XSL stylesheet provided with HL7 CDA to allow viewing annotation XML documents in a web browser, and plan to adapt existing tools for translating annotation documents between CDA+GrAF and the UIMA and GATE frameworks. This common data model may ease directly comparing NLP tools and applications, combining their output, transforming and "translating" annotations between different NLP applications, and eventually "plug-and-play" of different modules in NLP applications. Copyright © 2011 Elsevier Inc. All rights reserved.

Reversible CO binding enables tunable CO/H₂ and CO/N₂ separations in metal-organic frameworks with exposed divalent metal cations.

Science.gov (United States)

Bloch, Eric D; Hudson, Matthew R; Mason, Jarad A; Chavan, Sachin; Crocellà, Valentina; Howe, Joshua D; Lee, Kyuho; Dzubak, Allison L; Queen, Wendy L; Zadrozny, Joseph M; Geier, Stephen J; Lin, Li-Chiang; Gagliardi, Laura; Smit, Berend; Neaton, Jeffrey B; Bordiga, Silvia; Brown, Craig M; Long, Jeffrey R

2014-07-30

Six metal-organic frameworks of the M2(dobdc) (M = Mg, Mn, Fe, Co, Ni, Zn; dobdc(4-) = 2,5-dioxido-1,4-benzenedicarboxylate) structure type are demonstrated to bind carbon monoxide reversibly and at high capacity. Infrared spectra indicate that, upon coordination of CO to the divalent metal cations lining the pores within these frameworks, the C-O stretching frequency is blue-shifted, consistent with nonclassical metal-CO interactions. Structure determinations reveal M-CO distances ranging from 2.09(2) Å for M = Ni to 2.49(1) Å for M = Zn and M-C-O angles ranging from 161.2(7)° for M = Mg to 176.9(6)° for M = Fe. Electronic structure calculations employing density functional theory (DFT) resulted in good agreement with the trends apparent in the infrared spectra and crystal structures. These results represent the first crystallographically characterized magnesium and zinc carbonyl compounds and the first high-spin manganese(II), iron(II), cobalt(II), and nickel(II) carbonyl species. Adsorption isotherms indicate reversible adsorption, with capacities for the Fe, Co, and Ni frameworks approaching one CO per metal cation site at 1 bar, corresponding to loadings as high as 6.0 mmol/g and 157 cm(3)/cm(3). The six frameworks display (negative) isosteric heats of CO adsorption ranging from 52.7 to 27.2 kJ/mol along the series Ni > Co > Fe > Mg > Mn > Zn, following the Irving-Williams stability order. The reversible CO binding suggests that these frameworks may be of utility for the separation of CO from various industrial gas mixtures, including CO/H2 and CO/N2. Selectivities determined from gas adsorption isotherm data using ideal adsorbed solution theory (IAST) over a range of gas compositions at 1 bar and 298 K indicate that all six M2(dobdc) frameworks could potentially be used as solid adsorbents to replace current cryogenic distillation technologies, with the choice of M dictating adsorbent regeneration energy and the level of purity of the resulting gases.

CO2 Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues

Directory of Open Access Journals (Sweden)

Ana Arenillas

2013-10-01

Full Text Available Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO2 adsorption properties, with interestingly high gas selectivities for CO2 (α > 200 at a gas composition of 15% CO2/85% N2, 273K, 1 bar and capacities (>2 mmol·g−1 at 273 K. Both CO2 isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO2 which may be correlated with both: N content in the leather residues and ultrasmall pore sizes.

CO2 Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues

Science.gov (United States)

Bermúdez, José M.; Dominguez, Pablo Haro; Arenillas, Ana; Cot, Jaume; Weber, Jens; Luque, Rafael

2013-01-01

Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO2 adsorption properties, with interestingly high gas selectivities for CO2 (α > 200 at a gas composition of 15% CO2/85% N2, 273K, 1 bar) and capacities (>2 mmol·g−1 at 273 K). Both CO2 isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO2 which may be correlated with both: N content in the leather residues and ultrasmall pore sizes. PMID:28788352

Research and development of technologies for CO{sub 2} fixation and effective utilization thereof, etc., in fiscal 1998. Report on research and development of technologies for the effective use of CO{sub 2} by virtue of contact hydrogenation (CO{sub 2} separation and recovery system of the next-generation type); 1998 nendo nisanka tanso koteika yuko riyo gijutsu nado kenkyu kaihatsu jigyo. Sesshoku suisoka hanno riyo nisanka tanso yuko riyo gijutsu kenkyu kaihatsu jigyo kenkyu kaihatsu jigyo (jisedaigata shoene CO{sub 2} bunri kaishu system ni kansuru chosa kenkyu hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches were conducted for the goal of proposing a totally new process enhanced in efficiency and energy saving, and capable of CO2 separation. In fiscal 1997, hydrocarbon materials were reformed by oxygen separated within a system allowing fuel cells to generate power efficiently, when all the emitted CO2 was separated and recovered within the system. Furthermore, cold heat was utilized for the acquisition of liquefied CO2 gas products. A part of oxygen separated at the fuel cell cathode was recycled into the combustion section external to the tubular reaction reformer, and CO2 was separated by mere cooling from the combustion products for the simultaneous production of by-products such as high-purity nitrogen gas and liquefied CO2 for a great improvement in economy. In fiscal 1998, the system was improved. Proposed then was a new system in which an oxygen partial oxidation type reformer assumed the nuclear role, separating all the oxygen at the cathode, reusing part thereof for oxygen enrichment, and feeding the rest thereof into the reformer. The design realized the recycling of the whole of the products of the two cell electrodes into the reformer for the maximum reuse of the products of the hydrogen/oxygen separation function. (NEDO)

Dansk oversættelse af MiDAS, et redskab til assessment af musikterapi for personer med demens

DEFF Research Database (Denmark)

Ridder, Hanne Mette Ochsner; Lykkegaard, Chris; McDermott, Orii

2018-01-01

Music in Dementia Assessment Scales, MiDAS, er udviklet til at vurdere ændringer i trivsel hos borgere med demens som har deltaget i musikterapi. Målingen udføres af 1) personale før og efter musikterapien for at vurdere om der er en indflydelse i hverdagssituationer efterfølgende, eller af 2......) musikterapeuten umiddelbart efter sessionen for at vurdere forandringer i selve sessionen. Der har været stor interesse for at anvende MiDAS i flere Europæiske lande, herunder Danmark. Derfor undersøgte udviklerne af MiDAS hvilke procedurer der anvendes til oversættelse og kulturel tilpasning af...... assessmentredskaber, og anbefalede på den baggrund en ti-trins procedure. Vi anvendte denne procedure til oversættelsen af MiDAS og således udviklingen af den danske MiDAS-DK. Den danske version af MiDAS er afprøvet af mere end 20 fagpersoner på baggrund af 296 udfyldte MiDAS-skemaer. Målet med artiklen er...

Plasticization-resistant hollow fiber membranes for CO2/CH4 separation based on a thermally crosslinkable polyimide

KAUST Repository

Chen, Chien-Chiang

2011-10-01

Decarboxylation-induced thermal crosslinking has been demonstrated to be effective for stabilizing membranes against plasticization in dense films. This study extends this promising crosslinking approach from dense films to industrially relevant asymmetric hollow fiber membranes. Crosslinkable asymmetric hollow fiber membranes were spun from a carboxylic acid containing polyimide, 6FDA-DAM:DABA. Dope and spinning conditions were optimized to obtain fibers with a defect-free selective skin layer. It is found that slightly defective fibers suffered severe selectivity loss after thermal crosslinking, suggesting that defect-free property is essential to the performance of the resulting crosslinked hollow fiber membranes. The crosslinked fibers were tested for CO 2/CH 4 separation. The excellent plasticization resistance under high pressure feeds (with highest CO 2 partial pressure of 400psia) suggests that these robust membranes are promising for aggressive natural gas purification. © 2011 Elsevier B.V.

Plasticization-resistant hollow fiber membranes for CO2/CH4 separation based on a thermally crosslinkable polyimide

KAUST Repository

Chen, Chien-Chiang; Qiu, Wulin; Miller, Stephen J.; Koros, William J.

2011-01-01

Decarboxylation-induced thermal crosslinking has been demonstrated to be effective for stabilizing membranes against plasticization in dense films. This study extends this promising crosslinking approach from dense films to industrially relevant asymmetric hollow fiber membranes. Crosslinkable asymmetric hollow fiber membranes were spun from a carboxylic acid containing polyimide, 6FDA-DAM:DABA. Dope and spinning conditions were optimized to obtain fibers with a defect-free selective skin layer. It is found that slightly defective fibers suffered severe selectivity loss after thermal crosslinking, suggesting that defect-free property is essential to the performance of the resulting crosslinked hollow fiber membranes. The crosslinked fibers were tested for CO 2/CH 4 separation. The excellent plasticization resistance under high pressure feeds (with highest CO 2 partial pressure of 400psia) suggests that these robust membranes are promising for aggressive natural gas purification. © 2011 Elsevier B.V.

Separation and capture of CO2 from large stationary sources and sequestration in geological formations--coalbeds and deep saline aquifers.

Science.gov (United States)

White, Curt M; Strazisar, Brian R; Granite, Evan J; Hoffman, James S; Pennline, Henry W

2003-06-01

The topic of global warming as a result of increased atmospheric CO2 concentration is arguably the most important environmental issue that the world faces today. It is a global problem that will need to be solved on a global level. The link between anthropogenic emissions of CO2 with increased atmospheric CO2 levels and, in turn, with increased global temperatures has been well established and accepted by the world. International organizations such as the United Nations Framework Convention on Climate Change (UNFCCC) and the Intergovernmental Panel on Climate Change (IPCC) have been formed to address this issue. Three options are being explored to stabilize atmospheric levels of greenhouse gases (GHGs) and global temperatures without severely and negatively impacting standard of living: (1) increasing energy efficiency, (2) switching to less carbon-intensive sources of energy, and (3) carbon sequestration. To be successful, all three options must be used in concert. The third option is the subject of this review. Specifically, this review will cover the capture and geologic sequestration of CO2 generated from large point sources, namely fossil-fuel-fired power gasification plants. Sequestration of CO2 in geological formations is necessary to meet the President's Global Climate Change Initiative target of an 18% reduction in GHG intensity by 2012. Further, the best strategy to stabilize the atmospheric concentration of CO2 results from a multifaceted approach where sequestration of CO2 into geological formations is combined with increased efficiency in electric power generation and utilization, increased conservation, increased use of lower carbon-intensity fuels, and increased use of nuclear energy and renewables. This review covers the separation and capture of CO2 from both flue gas and fuel gas using wet scrubbing technologies, dry regenerable sorbents, membranes, cryogenics, pressure and temperature swing adsorption, and other advanced concepts. Existing

Lyden-af-Leg

DEFF Research Database (Denmark)

Toft, Herdis

Præsentation af seniorforsker-projekt Lyden-af-Leg i et traderingsperspektiv og med indledende fokus på YouTube som traderings-platform.......Præsentation af seniorforsker-projekt Lyden-af-Leg i et traderingsperspektiv og med indledende fokus på YouTube som traderings-platform....

Sundhedseffekter af luftforurening-beregningspriser

DEFF Research Database (Denmark)

Andersen, M. S.; Frohn, L. M.; Jensen, S. S.

Denne rapport afrapporterer det fortsatte arbejde med udvikling af miljøøkonomiske beregningspriser. På grundlag af EcoSense 4.0 fra ExternE-projektet, er der foretaget nye beregninger af eksternaliteter ved luftforurening med sundhedseffekter. Samtidig giver rapporten en vurdering af luftspredni......Denne rapport afrapporterer det fortsatte arbejde med udvikling af miljøøkonomiske beregningspriser. På grundlag af EcoSense 4.0 fra ExternE-projektet, er der foretaget nye beregninger af eksternaliteter ved luftforurening med sundhedseffekter. Samtidig giver rapporten en vurdering af...

Anvendelse af alternative isoleringsmaterialer

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place

2003-01-01

Resume af By og Byg Anvisning 207 om anvendelse af alternative isoleringsmaterialer, udarbejdet af Statens Byggeforskningsinstitut under udviklingsprogrammet "Miljø- og arbejdsmiljøvenlig isolering"......Resume af By og Byg Anvisning 207 om anvendelse af alternative isoleringsmaterialer, udarbejdet af Statens Byggeforskningsinstitut under udviklingsprogrammet "Miljø- og arbejdsmiljøvenlig isolering"...

Nanoparticle separation with a miniaturized asymmetrical flow field-flow fractionation cartridge

Science.gov (United States)

Müller, David; Cattaneo, Stefano; Meier, Florian; Welz, Roland; deMello, Andrew

2015-07-01

Asymmetrical Flow Field-Flow Fractionation (AF4) is a separation technique applicable to particles over a wide size range. Despite the many advantages of AF4, its adoption in routine particle analysis is somewhat limited by the large footprint of currently available separation cartridges, extended analysis times and significant solvent consumption. To address these issues, we describe the fabrication and characterization of miniaturized AF4 cartridges. Key features of the scale-down platform include simplified cartridge and reagent handling, reduced analysis costs and higher throughput capacities. The separation performance of the miniaturized cartridge is assessed using certified gold and silver nanoparticle standards. Analysis of gold nanoparticle populations indicates shorter analysis times and increased sensitivity compared to conventional AF4 separation schemes. Moreover, nanoparticulate titanium dioxide populations exhibiting broad size distributions are analyzed in a rapid and efficient manner. Finally, the repeatability and reproducibility of the miniaturized platform are investigated with respect to analysis time and separation efficiency.

Electrochemical impedance spectroscopy analysis with a symmetric cell for LiCoO2 cathode degradation correlated with Co dissolution

Directory of Open Access Journals (Sweden)

Hiroki Nara

2016-04-01

Full Text Available Static degradation of LiCoO2 cathodes is a problem that hinders accurate analysis using our developed separable symmetric cell. Therefore, in this study we investigate the static degradation of LiCoO2 cathodes in separable symmetric cells by electrochemical impedance spectroscopy (EIS and inductively coupled plasma analyses. EIS measurements of LiCoO2 cathodes are conducted in various electrolytes, with different anions and with or without HF and/or H2O. This allows us to determine the static degradation of LiCoO2 cathodes relative to their increase of charge transfer resistance. The increase of the charge transfer resistance of the LiCoO2 cathodes is attributed to cobalt dissolution from the active material of LiCoO2. Cobalt dissolution from LiCoO2 is revealed to occur even at low potential in the presence of HF, which is generated from LiPF6 and H2O. The results indicate that avoidance of HF generation is important for the analysis of lithium-ion battery electrodes by using the separable cell. These findings reveal the condition to achieve accurate analysis by EIS using the separable cell.

A pan-cancer analysis of transcriptome changes associated with somatic mutations in U2AF1 reveals commonly altered splicing events.

Directory of Open Access Journals (Sweden)

Angela N Brooks

Full Text Available Although recurrent somatic mutations in the splicing factor U2AF1 (also known as U2AF35 have been identified in multiple cancer types, the effects of these mutations on the cancer transcriptome have yet to be fully elucidated. Here, we identified splicing alterations associated with U2AF1 mutations across distinct cancers using DNA and RNA sequencing data from The Cancer Genome Atlas (TCGA. Using RNA-Seq data from 182 lung adenocarcinomas and 167 acute myeloid leukemias (AML, in which U2AF1 is somatically mutated in 3-4% of cases, we identified 131 and 369 splicing alterations, respectively, that were significantly associated with U2AF1 mutation. Of these, 30 splicing alterations were statistically significant in both lung adenocarcinoma and AML, including three genes in the Cancer Gene Census, CTNNB1, CHCHD7, and PICALM. Cell line experiments expressing U2AF1 S34F in HeLa cells and in 293T cells provide further support that these altered splicing events are caused by U2AF1 mutation. Consistent with the function of U2AF1 in 3' splice site recognition, we found that S34F/Y mutations cause preferences for CAG over UAG 3' splice site sequences. This report demonstrates consistent effects of U2AF1 mutation on splicing in distinct cancer cell types.

Beregning af nitratudvaskning

DEFF Research Database (Denmark)

Petersen, Jens; Petersen, Bjørn Molt; Blicher-Mathiesen, Gitte

2006-01-01

I forbindelse med kommunalreformen ønskes en ensartet forvaltning af reglerne for vurdering af virkninger på miljøet (VVM) ved ansøgninger om udvidelse af husdyrbrug, herunder beregning af nitratudvaskningen. Rapporten foreslår et beregningskoncept, der bygger på den ansøgende bedrifts samlede kv...

Role of intrachain rigidity in the plasticization of intrinsically microporous triptycene-based polyimide membranes in mixed-Gas CO2/CH4 separations

KAUST Repository

Swaidan, Raja

2014-11-11

Based on high-pressure pure- and mixed-gas (50:50) CO2/CH4 separation properties of two intrinsically microporous triptycene-based polyimides (TPDA-TMPD and TPDA-6FpDA), the intrachain rigidity central to "conventional PIM" design principles is not a singular solution to intrinsic plasticization resistance. Despite the significant intrachain rigidity in TPDA-TMPD, a 300% increase in PMIX(CH4), 50% decrease in α(CO2/CH4) from 24 to 12, and continuous increase in PMIX(CO2) occurred from 4 to 30 bar. On the other hand, the more flexible and densely packed TPDA-6FpDA exhibited a slight upturn in PMIX(CO2) at 20 bar similar to a dense cellulose acetate (CA) film, also reported here, despite a 4-fold higher CO2 sorption capacity. Microstructural investigations suggest that the interconnected O2- and H2-sieving ultramicroporosity of TPDA-TMPD is more sensitive to slight CO2-induced dilations and is the physical basis for a more extensive and accelerated plasticization. Interchain rigidity, potentially by interchain interactions, is emphasized and may be facilitated by intrachain mobility.

Identifikation af referencevandløb til implementering af vandrammedirektivet i Danmark

DEFF Research Database (Denmark)

Kristensen, Esben Astrup; Baattrup-Pedersen, Annette; Skriver, Jens

Definition og beskrivelse af referencetilstanden er centralt for implementering af vandrammedirektivet, da bedømmelse af den økologiske tilstand sker som afvigelsen fra den upåvirkede referencetilstand. I denne rapport præsenteres analyser af danske, udenlandske og historiske data med det formål...

Phase separation, effects of magnetic field and high pressure on charge ordering in γ-Na0.5CoO2

International Nuclear Information System (INIS)

Yang, H.X.; Shi, Y.G.; Nie, C.J.; Wu, D.; Yang, L.X.; Dong, C.; Yu, H.C.; Zhang, H.R.; Jin, C.Q.; Li, J.Q.

2005-01-01

Transmission electron microscopy (TEM) observations reveal the presence of complex superstructures and remarkable phase separation in association with Na-ordering phenomenon in γ-Na 0.5 CoO 2 . Resistivity and magnetization measurements indicate that three phase transitions at the temperatures of 25, 53 and 90 K, respectively, appear commonly in γ-Na 0.5 CoO 2 samples. Under a high pressure up to 10 kbar, the low-temperature transport properties show certain changes below the charge order transition; under an applied magnetic field of 7 T, phase transitions at around 25 and 53 K, proposed fundamentally in connection with alternations of magnetic structure and charge ordering maintain almost unchanged

Restaurering af Skjern Å

DEFF Research Database (Denmark)

Jessen, K.; Boysen Larsen, B.; Bundgaard, P.

Denne rapport indeholder resultaterne af den natur- og miljøovervågning, der blev iværksat som en del af naturgenopretningen af Skjern Å 1999-2002. Ved projektet ophørte den kunstige afvanding af den vestlige del af Skjern Å dalen. Størstedelen af de dyrkede arealer ændredes til ekstensive græsni...

Vibrational dynamics of adsorbed CO2: Separability of the CO2 asymmetric stretching mode

Czech Academy of Sciences Publication Activity Database

Bludský, Ota; Nachtigall, Petr; Špirko, Vladimír

2011-01-01

Roč. 76, č. 6 (2011), s. 669-682 ISSN 0010-0765 R&D Projects: GA MŠk LC512; GA ČR GAP208/11/0436; GA MŠk(CZ) ME10032 Grant - others:GA MŠk(CZ) KONTAKT-II(LH)-CH022 Institutional research plan: CEZ:AV0Z40550506 Keywords : adsorption of CO2 * vibrational dynamics * DFT calculations Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.283, year: 2011

Relevansen af Aristoteles' etik for konceptionen af eksistentiel terapi

DEFF Research Database (Denmark)

Dræby, Anders

Siden sin undfangelse i begyndelsen af det 20. århundrede har den eksistentielle terapi repræsenteret et filosofisk funderet alternativ til de former for terapeutisk praksis, der er funderet i den funktionalistiske medicinske metafysik. Anvendelse af elementer fra Aristoteles' etik muliggør en...... fremhævelse af den eksistentielle terapi som en praktisk eksistensfænomenologisk livskunst, hvis anliggende er en frembringelse af det enkelte menneskes muligheder fra det skjulte og ind i det uskjulte, så mennesket viser sig som det er ved sig selv...

Characterization of hydrotalcite materials for CO2 selective membranes

Energy Technology Data Exchange (ETDEWEB)

Feuillade, V.C.; Haije, W.G. [ECN Hydrogen and Clean Fossil Fuels, Petten (Netherlands)

2006-07-15

The present concern about climate change has urged researchers and engineers all over the world to go and look for ways of reducing greenhouse gas emissions. Largescale CO2 emissions occur at power plants burning fossil fuels or e.g. the production of hydrogen from carbonaceous feed. In these cases pre- or post-combustion CO2 capture techniques followed by CO2 storage seems a promising route for reducing emissions. Prerequisite in these processes is the effective separation of CO2 from mixed gaseous process streams. The purpose of this work is to develop CO2 membranes to allow for the combination of natural gas reforming with separation of H2 and CO2 in separation enhanced reactors, i.e. membrane reactors, for carbon-free hydrogen production or electricity generation. This paper describes the materials' properties of hydrotalcites, a promising class of compounds for CO2 membranes. They have already proven their applicability as CO2 sorbent in sorption enhanced reaction processes. It is of fundamental importance to know the structural stability of this compound in the operational window of a chosen membrane reactor prior to any membrane fabrication. To this end, in-situ XRPD and DRIFTS as well as TGA-MS and SEM-EDX measurements have been performed on commercial (Pural) and hydrothermally synthesized homemade samples.

Om distributionen af hvidhed

DEFF Research Database (Denmark)

Frello, Birgitta

2007-01-01

Med udgangspunkt i John Fords Western, Forfølgeren fra 1956, præsenteres en analyse af repræsentationer af race og overskridelse af raceskel, særligt i relation til konstitueringen af subjektpositioner, hvorfra spørgsmål om hvidhed og ikke-hvidhed kan afgøres.......Med udgangspunkt i John Fords Western, Forfølgeren fra 1956, præsenteres en analyse af repræsentationer af race og overskridelse af raceskel, særligt i relation til konstitueringen af subjektpositioner, hvorfra spørgsmål om hvidhed og ikke-hvidhed kan afgøres....

Fabrication of 6FDA-durene membrane incorporated with zeolite T and aminosilane grafted zeolite T for CO2/CH4 separation

Science.gov (United States)

Jusoh, Norwahyu; Fong Yeong, Yin; Keong Lau, Kok; Shariff, Azmi Mohd

2017-08-01

In the present work, zeolite T and aminosilane grafted zeolite T are embedded into 6FDA-durene polyimide phase for the fabrication of mixed matrix membranes (MMMs). FESEM images demonstrated that the improvement of interfacial adhesion between zeolite and polymer phases in MMM loaded with aminosilane grafted zeolite T was not significant as compared to zeolite T/6FDA-durene MMM. From the gas permeation test, CO2/CH4 selectivity up to 26.4 was achieved using MMM containing aminosilane grafted zeolite T, while MMM loaded with ungrafted zeolite T showed CO2/CH4 selectivity of 19.1. In addition, MMM incorporated with aminosilane grafted zeolite T particles successfully lies on Robeson upper bound 2008, which makes it an attractive candidate for CO2/CH4 separation.

Energirenovering af Traneparken

DEFF Research Database (Denmark)

Rose, Jørgen; Thomsen, Kirsten Engelund; Mørck, Ove

Nærværende rapport udgør en del af afrapporteringen af PSO ELFORSK projektet Vejledning for energirenovering af boligblokke til lavenergiklasse 2015 og 2020. Arbejdet har været finansieret af PSO midler via ELFORSK, projekt: 347-023. Formålet med projektet er at udvikle en vejledning for dybtgående...

Peter Petersen & Co. A/S

DEFF Research Database (Denmark)

Nygaard, Erik

1986-01-01

Peter Petersen & Co. A/S : administrations- og lagerbygning kommenteret af: Erik Nygaard. Resumé på engelsk & tysk.......Peter Petersen & Co. A/S : administrations- og lagerbygning kommenteret af: Erik Nygaard. Resumé på engelsk & tysk....

Retroviral insertional mutagenesis identifies Zeb2 activation as a novel leukemogenic collaborating event in CALM-AF10 transgenic mice.

Science.gov (United States)

Caudell, David; Harper, David P; Novak, Rachel L; Pierce, Rachel M; Slape, Christopher; Wolff, Linda; Aplan, Peter D

2010-02-11

The t(10;11) translocation results in a CALM-AF10 fusion gene in a subset of leukemia patients. Expression of a CALM-AF10 transgene results in leukemia, with prolonged latency and incomplete penetrance, suggesting that additional events are necessary for leukemic transformation. CALM-AF10 mice infected with the MOL4070LTR retrovirus developed acute leukemia, and ligation-mediated polymerase chain reaction was used to identify retroviral insertions at 19 common insertion sites, including Zeb2, Nf1, Mn1, Evi1, Ift57, Mpl, Plag1, Kras, Erg, Vav1, and Gata1. A total of 26% (11 of 42) of the mice had retroviral integrations near Zeb2, a transcriptional corepressor leading to overexpression of the Zeb2-transcript. A total of 91% (10 of 11) of mice with Zeb2 insertions developed B-lineage acute lymphoblastic leukemia, suggesting that Zeb2 activation promotes the transformation of CALM-AF10 hematopoietic precursors toward B-lineage leukemias. More than half of the mice with Zeb2 integrations also had Nf1 integrations, suggesting cooperativity among CALM-AF10, Zeb2, and Ras pathway mutations. We searched for Nras, Kras, and Ptpn11 point mutations in the CALM-AF10 leukemic mice. Three mutations were identified, all of which occurred in mice with Zeb2 integrations, consistent with the hypothesis that Zeb2 and Ras pathway activation promotes B-lineage leukemic transformation in concert with CALM-AF10.

Improving the Photo-Oxidative Performance of Bi2MoO6 by Harnessing the Synergy between Spatial Charge Separation and Rational Co-Catalyst Deposition.

Science.gov (United States)

Wu, Xuelian; Hart, Judy N; Wen, Xiaoming; Wang, Liang; Du, Yi; Dou, Shi Xue; Ng, Yun Hau; Amal, Rose; Scott, Jason

2018-03-21

It has been reported that photogenerated electrons and holes can be directed toward specific crystal facets of a semiconductor particle, which is believed to arise from the differences in their surface electronic structures, suggesting that different facets can act as either photoreduction or photo-oxidation sites. This study examines the propensity for this effect to occur in faceted, plate-like bismuth molybdate (Bi 2 MoO 6 ), which is a useful photocatalyst for water oxidation. Photoexcited electrons and holes are shown to be spatially separated toward the {100} and {001}/{010} facets of Bi 2 MoO 6 , respectively, by facet-dependent photodeposition of noble metals (Pt, Au, and Ag) and metal oxides (PbO 2 , MnO x , and CoO x ). Theoretical calculations revealed that differences in energy levels between the conduction bands and valence bands of the {100} and {001}/{010} facets can contribute to electrons and holes being drawn to different surfaces of the plate-like Bi 2 MoO 6 . Utilizing this knowledge, the photo-oxidative capability of Bi 2 MoO 6 was improved by adding an efficient water oxidation co-catalyst, CoO x , to the system, whereby the extent of enhancement was shown to be governed by the co-catalyst location. A greater oxygen evolution occurred when CoO x was selectively deposited on the hole-rich {001}/{010} facets of Bi 2 MoO 6 compared to when CoO x was randomly located across all of the facets. The elevated performance exhibited for the selectively loaded CoO x /Bi 2 MoO 6 was ascribed to the greater opportunity for hole trapping by the co-catalyst being accentuated over other potentially detrimental effects, such as the co-catalyst acting as a recombination medium and/or covering reactive sites. The results indicate that harnessing the synergy between the spatial charge separation and the co-catalyst location on the appropriate facets of plate-like Bi 2 MoO 6 can promote its photocatalytic activity.

Supported Ionic Liquid Membranes and Ion-Jelly® Membranes with [BMIM][DCA]: Comparison of Its Performance for CO2 Separation

Directory of Open Access Journals (Sweden)

Ricardo Couto

2015-01-01

Full Text Available In this work, a supported ionic liquid membrane (SILM was prepared by impregnating a PVDF membrane with 1-butyl-3-methylimidazolium dicyanamide ([BMIM][DCA] ionic liquid. This membrane was tested for its permeability to pure gases (CO2, N2 and O2 and ideal selectivities were calculated. The SILM performance was also compared to that of Ion-Jelly® membranes, a new type of gelled membranes developed recently. It was found that the PVDF membrane presents permeabilities for pure gases similar or lower to those presented by the Ion-Jelly® membranes, but with increased ideal selectivities. This membrane presents also the highest ideal selectivity (73 for the separation of CO2 from N2 when compared with SILMs using the same PVDF support but with different ionic liquids.

Preparation and Characterization of Facilitated Transport Membranes Composed of Chitosan-Styrene and Chitosan-Acrylonitrile Copolymers Modified by Methylimidazolium Based Ionic Liquids for CO2 Separation from CH4 and N2

Directory of Open Access Journals (Sweden)

Ksenia V. Otvagina

2016-06-01

Full Text Available CO2 separation was found to be facilitated by transport membranes based on novel chitosan (CS–poly(styrene (PS and chitosan (CS–poly(acrylonitrile (PAN copolymer matrices doped with methylimidazolium based ionic liquids: [bmim][BF4], [bmim][PF6], and [bmim][Tf2N] (IL. CS plays the role of biodegradable film former and selectivity promoter. Copolymers were prepared implementing the latest achievements in radical copolymerization with chosen monomers, which enabled the achievement of outstanding mechanical strength values for the CS-based membranes (75–104 MPa for CS-PAN and 69–75 MPa for CS-PS. Ionic liquid (IL doping affected the surface and mechanical properties of the membranes as well as the gas separation properties. The highest CO2 permeability 400 Barrers belongs to CS-b-PS/[bmim][BF4]. The highest selectivity α (CO2/N2 = 15.5 was achieved for CS-b-PAN/[bmim][BF4]. The operational temperature of the membranes is under 220 °C.

Enhanced the performance of graphene oxide/polyimide hybrid membrane for CO2 separation by surface modification of graphene oxide using polyethylene glycol

Science.gov (United States)

Wu, Li-guang; Yang, Cai-hong; Wang, Ting; Zhang, Xue-yang

2018-05-01

Polyethylene glycol (PEG) with different molecular weights was first used to modify graphene oxide (GO) samples. Subsequently, polyimide (PI) hybrid membranes containing modified-GO were fabricated via in situ polymerization. The separation performance of these hybrid membranes was evaluated using permeation experiments for CO2 and N2 gases. The morphology characterization showed that PEG with suitable molecular weight could be successfully grafted on the GO surface. PEG modification altered the surface properties of GO and introduced defective structures onto GO surface. This caused strong surface polarity and high free volume of membranes containing PEG-modified GO, thereby improving the separation performance of membranes. The addition of PEG-GO with low molecular weight effectively increased gas diffusion through hybrid membranes. The hybrid membranes containing PEG-GO with large molecular weight had high solubility performance for CO2 gas due to the introduction of numerous polar groups into polymeric membranes. With the loading content of modified GO, the CO2 gas permeability of hybrid membranes initially increased but eventually decreased. The optimal content of modified GO in membranes reached 3.0 wt%. When too much PEG added (exceeding 30 g), some impurities formed on GO surface and some aggregates appeared in the resulting hybrid membrane, which depressed the membrane performance.

Elevated CO2 concentration around alfalfa nodules increases N2 fixation

OpenAIRE

Fischinger, Stephanie A.; Hristozkova, Marieta; Mainassara, Zaman-Allah; Schulze, Joachim

2009-01-01

Nodule CO2 fixation via PEPC provides malate for bacteroids and oxaloacetate for N assimilation. The process is therefore of central importance for efficient nitrogen fixation. Nodule CO2 fixation is known to depend on external CO2 concentration. The hypothesis of the present paper was that nitrogen fixation in alfalfa plants is enhanced when the nodules are exposed to elevated CO2 concentrations. Therefore nodulated plants of alfalfa were grown in a hydroponic system that allowed separate ae...

Influence of the cation substitution on the magnetic properties of LiCo2O4 and Li(Me,Co2O4 spinels

Directory of Open Access Journals (Sweden)

Gautier, J. L.

2004-08-01

Full Text Available Lithium-based cells LiCo2O4 have been characterized by magnetic techniques, looking at the influence of the partial substitution of cobalt by 3d or 4d transition metal elements (Fe, Ni, Cu, Cr, Mo. The non-substituted compound LiCo2O4 behaves as an antiferromagnet, with a Néel temperature TN of 30 K, although antiferromagnetic interactions are much more important, as suggested by a Weiss parameter Θ of the order of ‑225 K. In the solid solution Li(NixCo2‑xO4 the Weiss parameter Θ changes with x(Ni, reaching large positive values (e.g., Θ ~ +230 K, for x = 0.5. This phenomenon suggests the existence of a canted‑antiferromagnetic or ferrimagnetic structures with large ferromagnetic components. Substitution of cobalt by other 3d or 4d transition metals in the LiMe0.5Co1.5O4 series shows dramatic effects with respect to the non-substituted LiCo2O4 compound : copper completely suppresses the magnetic order, while iron increases TN to almost room temperature. No modifications are observed when molybdenum substitutes cobalt, while chromium transforms the AF order in a ferromagnetic one, with Tc of about 90 K.Se ha caracterizado por técnicas magnéticas, el efecto de la sustitución parcial de Co por elementos de transición 3d o 4d (Fe, Ni, Cu, Cr, Mo en celdas LiCo2O4 a base de litio. El compuesto no sustituído LiCo2O4, se comporta como un antiferromagneto de temperatura de Néel TN de 30 K, aunque existen interacciones antiferromagnéticas mucho más importantes, como lo indica un parámetro de Weiss Θ del orden de -225K. En la solución sólida Li(NixCo2‑xO4, el parámetro de Weiss Θ cambia con x(Ni, alcanzando valores positivos altos (e.g., Θ ~ +230K, para x=0.5. Este fenómeno sugiere la existencia de una estructura antiferromagnética inclinada (“AF-canted” o de una estructura ferrimagnética, donde predominan componentes ferromagnéticas importantes. La sustitución del cobalto por otros elementos de transición 3d o 4d en

Permeability and Selectivity of PPO/Graphene Composites as Mixed Matrix Membranes for CO2 Capture and Gas Separation

Directory of Open Access Journals (Sweden)

Riccardo Rea

2018-01-01

Full Text Available We fabricated novel composite (mixed matrix membranes based on a permeable glassy polymer, Poly(2,6-dimethyl-1,4-phenylene oxide (PPO, and variable loadings of few-layer graphene, to test their potential in gas separation and CO2 capture applications. The permeability, selectivity and diffusivity of different gases as a function of graphene loading, from 0.3 to 15 wt %, was measured at 35 and 65 °C. Samples with small loadings of graphene show a higher permeability and He/CO2 selectivity than pure PPO, due to a favorable effect of the nanofillers on the polymer morphology. Higher amounts of graphene lower the permeability of the polymer, due to the prevailing effect of increased tortuosity of the gas molecules in the membrane. Graphene also allows dramatically reducing the increase of permeability with temperature, acting as a “stabilizer” for the polymer matrix. Such effect reduces the temperature-induced loss of size-selectivity for He/N2 and CO2/N2, and enhances the temperature-induced increase of selectivity for He/CO2. The study confirms that, as observed in the case of other graphene-based mixed matrix glassy membranes, the optimal concentration of graphene in the polymer is below 1 wt %. Below such threshold, the morphology of the nanoscopic filler added in solution affects positively the glassy chains packing, enhancing permeability and selectivity, and improving the selectivity of the membrane at increasing temperatures. These results suggest that small additions of graphene to polymers can enhance their permselectivity and stabilize their properties.

Om Hegels opfattelse af Gorgias, set på baggrund af tidligere filosofihistorikeres fremstilling

DEFF Research Database (Denmark)

Huggler, Jørgen

2010-01-01

En undersøgelse af Hegels tolkning af sofisten Gorgias giver anledning til at se på receptionen af sofisterne hos notable filosofihistorikere i det 18. århundrede. En sådan undersøgelse viser, at Hegel har en original og velvillig tolkning af sofisterne koncentreret omkring begrebet Bildung og det...... at give grunde for noget. Hegels udlægning af Gorgias bygger på hans tolkning af eleaterne, især af Zenon. Når Hegel har en særlig tolkning af eleaterne, skyldes det hans egne mangeårige filosofiske bestræbelser, og en identificering af en særlig, immanent objektiv dialektik hos Zenon, som han finder......, at Gorgias fører videre. Hegels filosofiske forståelse er tilstrækkelig udviklet til at kunne knytte positive kommentarer til alle dele af diskussionen i Gorgias' ræsonnement Om det ikkeværende, eller Om naturen. Det lykkes dog bedst i forhold til de to første af Gorgias' tre underteser. I hegelsk perspektiv...

Ensretning af historieundervisningen

DEFF Research Database (Denmark)

Rønhede, Søren

2008-01-01

"Det er ikke kun i Putins Rusland, at statsmagten vil dirigere historieundervisningen." (Politiken havde fokuseret på "ensretning af historieundervisningen" i Rusland) "Kanonen fra 2006 er undfanget af Udvalget til Styrkelse af Historie i Folkeskolen. Dette udvalg havde regeringen nedsat; men bid...... bidrager kanonen til faglig styrkelse?" spørges der. Det vises, at flere kanonpunkter ikke er fagligt funderede, men af mytologisk art....

Separation of anthropogenic CO{sub 2} in the North Atlantic - methodological developments and measurements; Separation von anthropogenem CO{sub 2} im Nordatlantik - Methodische Entwicklungen und Messungen

Energy Technology Data Exchange (ETDEWEB)

Friis, K.

2001-07-01

The foci for this thesis were: (1) the development of a fully automated pH-system, and (2) the identification of anthropogenic CO{sub 2} in the subpolar North Atlantic based on measurements using this system. A spectrophotometric pH-system for discrete sea water sample analysis was developed. For the detection of the temporal increase in anthropogenic CO{sub 2}, the statistical method of Wallace (1995) was tested for its applicability in the subpolar gyre. The original method is based on a comparison of historical and recent data sets. For one of the data sets a predictive equation for C{sub T} is derived by multiple linear regression (MLR) based on several independent chemical and hydrographic parameters. The difference between a C{sub T} value measured at a later or earlier time with the C{sub T} value predicted using the MLR-equation can potentially give a measure of the anthropogenic CO{sub 2}-increase between the two sampling periods, independent of hydrographic or biologically-mediated changes within the water column.

Microwave-assisted nitric acid treatment of sepiolite and functionalization with polyethylenimine applied to CO{sub 2} capture and CO{sub 2}/N{sub 2} separation

Energy Technology Data Exchange (ETDEWEB)

Vilarrasa-García, E., E-mail: enrique@gpsa.ufc.br [Department of Chemical Engineering, Universidade Federal do Ceará, Campus do Pici, bl. 709, 60455-760 Fortaleza (Brazil); Cecilia, J.A., E-mail: jacecilia@uma.es [Department of Inorganic Chemistry, Cristallography and Mineralogy, Universidad de Málaga, Campus de Teatinos s/n, 29071 Málaga (Spain); Bastos-Neto, M., E-mail: mbn@ufc.br [Department of Chemical Engineering, Universidade Federal do Ceará, Campus do Pici, bl. 709, 60455-760 Fortaleza (Brazil); Cavalcante, C.L., E-mail: celio@gpsa.ufc.br [Department of Chemical Engineering, Universidade Federal do Ceará, Campus do Pici, bl. 709, 60455-760 Fortaleza (Brazil); Azevedo, D.C.S., E-mail: diana@gpsa.ufc.br [Department of Chemical Engineering, Universidade Federal do Ceará, Campus do Pici, bl. 709, 60455-760 Fortaleza (Brazil); Rodríguez-Castellón, E., E-mail: castellon@uma.es [Department of Inorganic Chemistry, Cristallography and Mineralogy, Universidad de Málaga, Campus de Teatinos s/n, 29071 Málaga (Spain)

2017-07-15

Highlights: • Textural properties of sepiolite can be enhanced by microwave assisted acid treatment. • CO{sub 2} uptake of sepiolite improved significantly after amine modification. • The highest CO{sub 2}/N{sub 2} selectivity is 440 mol CO{sub 2}/mol N{sub 2} at 338 K and low pressures. - Abstract: Sepiolite was treated in HNO{sub 3} solutions with the assistance of microwave radiation. This treatment caused the progressive depletion of Mg{sup 2+}, the gradual degradation of the sepiolite structure and the formation of an amorphous silica phase, which contributes to a noticeable increase of the surface area. The use of microwaves during acid treatment, after few minutes, led to materials with similar S{sub BET} to those obtained after 48 h with conventional heating methods. The influence of mineralogical impurities, crystallinity and chemical composition in the reactivity of sepiolite to this treatment was also studied. The obtained materials were impregnated with polyethylenimine and assessed for CO{sub 2} capture and CO{sub 2}/N{sub 2} selectivity at different temperatures. Experimental equilibrium data were fitted to Langmuir and Sips models. The adsorption data revealed that sepiolite can be an interesting adsorbent for CO{sub 2} capture, achieving a capacity of 1.70 mmol g{sup −1} at 338 K and 1 bar, providing a high CO{sub 2}/N{sub 2} selectivity (440 mol CO{sub 2}/mol N{sub 2}).

Del af eller uden for fællesskabet? – Rummet som medskaber af uformelle læreprocesser

Directory of Open Access Journals (Sweden)

Tina Bering Keiding

2012-09-01

Full Text Available Artiklen undersøger studerendes læringsoplevelser i projektorganiseret undervisning i individuelle grupperum og i åbent kontorlandskab. Den konkluderer, at de to studiemiljøer skaber vidt forskellige lærings-oplevelser. Det åbne rum tilbyder rige muligheder for inspiration og feedback og bidrager til fagligt og socialt tilhørsforhold. Endvidere synes det åbne rum at skabe bedre rammer for udvikling af lærings- og samarbejdskompetencer. De lukkede rum vanskeliggør både formel og uformel kontakt og giver mange studerende en oplevelse af at stå uden for fællesskabet. The paper examines students’ experiences with project organized teaching in two different spatial conditions: separate rooms and an open space office. It concludes that students experience the two types of spatiality to provide very different learning contexts. The advantages of multiple rooms arise from their affordance of spontaneous inspiration, feedback, and social inclusion. Further the findings suggest that the multiple group room assists in the development of competencies in the areas of collaboration and learning. In contrast the separate room challenge on both professional and informal social interaction.

Highly CO2-Selective Gas Separation Membranes Based on Segmented Copolymers of Poly(Ethylene oxide) Reinforced with Pentiptycene-Containing Polyimide Hard Segments.

Science.gov (United States)

Luo, Shuangjiang; Stevens, Kevin A; Park, Jae Sung; Moon, Joshua D; Liu, Qiang; Freeman, Benny D; Guo, Ruilan

2016-01-27

Poly(ethylene oxide) (PEO)-containing polymer membranes are attractive for CO2-related gas separations due to their high selectivity toward CO2. However, the development of PEO-rich membranes is frequently challenged by weak mechanical properties and a high crystallization tendency of PEO that hinders gas transport. Here we report a new series of highly CO2-selective, amorphous PEO-containing segmented copolymers prepared from commercial Jeffamine polyetheramines and pentiptycene-based polyimide. The copolymers are much more mechanically robust than the nonpentiptycene containing counterparts due to the molecular reinforcement mechanism of supramolecular chain threading and interlocking interactions induced by the pentiptycene structures, which also effectively suppresses PEO crystallization leading to a completely amorphous structure even at 60% PEO weight content. Membrane transport properties are sensitively affected by both PEO weight content and PEO chain length. A nonlinear correlation between CO2 permeability with PEO weight content was observed due to the competition between solubility and diffusivity contributions, whereby the copolymers change from being size-selective to solubility-selective when PEO content reaches 40%. CO2 selectivities over H2 and N2 increase monotonically with both PEO content and chain length, indicating strong CO2-philicity of the copolymers. The copolymer film with the longest PEO sequence (PEO2000) and highest PEO weight content (60%) showed a measured CO2 pure gas permeability of 39 Barrer, and ideal CO2/H2 and CO2/N2 selectivities of 4.1 and 46, respectively, at 35 °C and 3 atm, making them attractive for hydrogen purification and carbon capture.

Optimering af byggeprocessen via bedre/forøget brug af digitale modeller

DEFF Research Database (Denmark)

Carlsen, Mads; Grøn, Dorte Marie Frilund; Alon, Nevo

2013-01-01

Projektet klarlægger nødvendigheden for, og muligheder i, en struktureret og konsekvent planlægning ved anvendelsen af BIM i relation til projektering, udførelse og drift af byggeri. Der er udarbejdet et planlægningsværktøj, der muliggør en sådan planlægning. Samtidig kortlægges de nødvendige data......, der kan udtrækkes af en BIM model ved gennemførelsen af en LCA simulering. Projektet afsluttes med en præsentation af en udviklet demonstratorapplikation til gennemførelse af LCA simuleringer koblet med BIM modellen....

Overvågning af orkidéer 2000

DEFF Research Database (Denmark)

Wind, P.

resultaterne af orkidéovervågningen (Wind 2001). Hertil kommer præsentationen af projektet og dets resultater efter forløbet af de første tre år (Løjtnant 1991a) og en bearbejdning af projektets resultater for årene 1987-1995 (Wind 1997). I nærværende rapport undersøges skov-hullæbe for en eventuel sammenhæng...... mellem skudanlæggelsen udtrykt ved antallet af blomstrende og vegetative skud i et givet år og nedbørsmængder i august og september året før. Det er en udbredt antagelse at der er en sammenhæng mellem skudanlæggelse og mængden af nedbør det foregående år. Undersøgelser af skov-hullæbe populationer i...... truet og sårbar samt de to arter der er omfattet af Habitatdirektivets bilag 2. I 2000 kan det i forhold til 1999 konstateres at der i 15 bestande er optalt et øget antal skud. I 11 bestande er der noteret en nedgang i antallet af skud sammenlignet med optællingerne i 1999. Af disse er der 2 be...

Enhanced Performance of Polyurethane Hybrid Membranes for CO2 Separation by Incorporating Graphene Oxide: The Relationship between Membrane Performance and Morphology of Graphene Oxide.

Science.gov (United States)

Wang, Ting; Zhao, Li; Shen, Jiang-nan; Wu, Li-guang; Van der Bruggen, Bart

2015-07-07

Polyurethane hybrid membranes containing graphene oxide (GO) with different morphologies were prepared by in situ polymerization. The separation of CO2/N2 gas mixtures was studied using these novel membranes. The results from the morphology characterization of GO samples indicated that the oxidation process in the improved Hummers method introduced oxygenated functional groups into graphite, making graphite powder exfoliate into GO nanosheets. The surface defects on the GO sheets increased when oxidation increased due to the introduction of more oxygenated functional groups. Both the increase in oxygenated functional groups on the GO surface and the decrease in the number of GO layers leads to a better distribution of GO in the polymer matrix, increasing thermal stability and gas separation performance of membranes. The addition of excess oxidant destroyed the structure of GO sheets and forms structural defects, which depressed the separation performance of membranes. The hybrid membranes containing well-distributed GO showed higher permeability and permeability selectivity for the CO2. The formation of GO aggregates in the hybrid membranes depressed the membrane performance at a high content of GO.

Ionic-Liquid-Based CO2 Capture Systems: Structure, Interaction and Process.

Science.gov (United States)

Zeng, Shaojuan; Zhang, Xiangping; Bai, Lu; Zhang, Xiaochun; Wang, Hui; Wang, Jianji; Bao, Di; Li, Mengdie; Liu, Xinyan; Zhang, Suojiang

2017-07-26

The inherent structure tunability, good affinity with CO 2 , and nonvolatility of ionic liquids (ILs) drive their exploration and exploitation in CO 2 separation field, and has attracted remarkable interest from both industries and academia. The aim of this Review is to give a detailed overview on the recent advances on IL-based materials, including pure ILs, IL-based solvents, and IL-based membranes for CO 2 capture and separation from the viewpoint of molecule to engineering. The effects of anions, cations and functional groups on CO 2 solubility and selectivity of ILs, as well as the studies on degradability of ILs are reviewed, and the recent developments on functionalized ILs, IL-based solvents, and IL-based membranes are also discussed. CO 2 separation mechanism with IL-based solvents and IL-based membranes are explained by combining molecular simulation and experimental characterization. Taking into consideration of the applications and industrialization, the recent achievements and developments on the transport properties of IL fluids and the process design of IL-based processes are highlighted. Finally, the future research challenges and perspectives of the commercialization of CO 2 capture and separation with IL-based materials are posed.

Durability of the Solid Oxide Cells for Co-Electrolysis of Steam and Carbon Dioxide under High Current Densities

OpenAIRE

Tao, Youkun; Mogensen, Mogens Bjerg; Ebbesen, Sune Dalgaard

2013-01-01

Produktion af brint og syntesegas (CO + H2) ved hjælp fastoxid elektrolyseceller (SOECs) er blevet stadig mere attraktiv på grund af den høje oliepris, evnen til at omdanne og opbevare fluktuerende energi fra vedvarende energikilder samt den generelle interesse i brint teknologi og CO2- neutral energi systemer. Stabiliteten af SOECs er afgørende for anvendelsen af denne teknologi.I dette arbejde er en række galvanostatiske stabilitets tests blevet udført ved høje strømtætheder på op til 2,0 A...

A strain-controlled C2N monolayer membrane for gas separation in PEMFC application

Science.gov (United States)

Deng, Shengwei; Hu, Hui; Zhuang, Guilin; Zhong, Xing; Wang, Jianguo

2018-05-01

Ultrathin membranes with controllable pore sizes have great potential to realize high-selectivity gas separation at low energy cost, especially for those mixtures with narrow size distributions. Using a combination of van der Waals-corrected density functional theory (DFT) calculations and molecular dynamics (MD) simulation, we examine the separation ability of biaxial stretched monolayer C2N nanosheets which is applied to the O2 separation from CO/CO2/O2 mixtures in the cathode of proton exchange membrane fuel cells (PEMFC). The DFT calculations show that the diffusion energy barrier for molecules passing through the membrane followed by CO, CO2 and O2 in descending order, and an overall decrease of energy barriers due to the widen the pore size is observed with the increase of applied strains. Furthermore, MD results show that the nanosheet can effectively purify O2 from CO2 and CO with a strain from 8% to 10%. It confirms that the selectivity is determined by the electronic structure related interaction in addition to the kinetic diameter of individual molecules. The O2 permeability is improved progressively with further increase of strain, and small amount of CO2 begins to permeate through the nanosheet at relatively large strain, while the excellent CO isolation is not compromised until the theoretical maximum strain.

Styring af kommunal digitalisering

DEFF Research Database (Denmark)

Jæger, Birgit

2017-01-01

Digitalisering af både interne arbejdsprocesser og kommunikation med borgere og virksomheder har længe været en vigtig faktor i moderniseringen af den offentlige sektor. Derfor er der stort fokus på styring af digitaliseringen. Denne artikel undersøger, dels hvordan digitaliseringen i den kommunale...... sektor styres, og dels hvilke styringsparadigmer der kan identificeres. Med udgangspunkt i en konkret kommune analyseres styringen af digitalisering gennem et hierarki af offentlige digitaliseringsstrategier. Gennem udvikling af en helt ny form for organisering, en såkaldt Digitaliseringsforening...

Livscyklusvurdering af basiskemikalier

DEFF Research Database (Denmark)

Olsen, Stig Irving

1998-01-01

Dette resumé af metoder og væsentlige erfaringer fra erhvervsforskerprojektet Livscyklusvurdering af basiskemikalier er skrevet i erkendelse af, at hovedrapporten er for omfattende til en hurtig introduktion i problemstillingerne. Formålet med denne rapport er derfor at give et kort overblik over...

Globalisering af uddannelse

DEFF Research Database (Denmark)

Jensen, Henning Høgh

2005-01-01

Det globale marked for uddannelse er i voldsom vækst og er ved at blive et af Danmarks vigtigste vareområder. Hvorledes kan KVL agere i globaliseringen af uddannelse for at sikre en høj kvalitet af egne kandidater med gode jobmuligheder?...

A study of CO2 precipitation method considering an ionic CO2 and Ca(OH)2 slurry

International Nuclear Information System (INIS)

Park, Sangwon; Jo, Hoyong; Kang, Dongwoo; Park, Jinwon

2014-01-01

CCS (carbon capture and storage) is the most popular technology used for the reduction of CO 2 in the post-combustion stage. However, the CCS process has some disadvantages including uncertainty about the stability of the land that is used to store the separated CO 2 . Consequently, CCU (carbon capture and utilization) technologies have recently received increased attention as a possible replacement for CCS. In this study, we utilized CO 2 fixation methods by using the metal carbonate mechanism. We selected 5 and 30 wt% MEA (mono-ethanolamine) solutions to rapidly make a carbonate and Ca(OH) 2 slurry. In all of the experiments, normal temperature and pressure conditions were maintained (except during desorption to check for residual CO 2 in the MEA solution). Consequently, most of the CO 2 was converted to carbonate. The MEA converted CO 2 to ionic CO 2 and rapidly created calcium carbonate. Also the formed solids that were observed were determined to be CaCO 3 and Ca(OH) 2 by X-ray diffractometry. Also, the MEA solution could be reused to absorb CO 2 . Therefore, we have confirmed the development of our suggested CCS process. This process has the ability not only to reuse emitted CO 2 , but it can also be employed to reuse construction wastes that include heavy metals. - Highlights: • We propose novel CO 2 conversion technology by utilizing an amine solution. • In this study, alkaline solutions were used to produce CO 2 precipitate. • The MEA (mono-ethanolamine) solution has a sufficient potential to fix CO 2 with metal sources under moderate condition. • Also, the Ca(OH) 2 slurry yielded enough Ca 2+ ions to make carbonate

Udvikling af vejledningspraksis i kurser for undervisere i brugen af blended learning-aktiviteter

DEFF Research Database (Denmark)

Stenalt, Maria Hvid; Wichmann-Hansen, Gitte; Rossen, Dorte Sidelmann

Hvert semester tilbyder Center for Undervisning og Læring (CUL) ved School of Business and Social Sciences ved Aarhus Universitet et 1-årig langt kompetenceudviklingsforløb i brugen af blended learning for lektorer og professorer. I løbet af denne periode skal deltagerne gennemføre et indledende...... blended learning-kursusforløb på 5 uger efterfulgt af en udviklings- og afprøvningsfase. Som afslutning skal deltagerne skrive en refleksionsrapport. Forløbet indebærer to vejledningsmøder med en eller flere af de undervisningsudviklere fra CUL, der er ansvarlige for forløbet: 1) Et individuelt...... vejledningsmøde, hvor deltagerne skal finde frem til, hvordan de vil eller kan omlægge deres undervisning til blended learning og 2) et kollektivt vejledningsmøde efter første udviklingsfase, hvor deltagerne modtager feedback på deres igangværende udviklingstiltag fra gruppemedlemmer og undervisningsudviklere. Et...

On-board co2 capture and storage with metal organic framework

KAUST Repository

Eddaoudi, Mohamed

2016-03-17

In general, this disclosure describes method of capturing and storing CO2 on a vehicle. The method includes contacting an vehicle exhaust gas with one or more of a first metal organic framework (MOF) composition sufficient to separate CO2 from the exhaust gas, contacting the separated CO2 with one or more of a second MOF composition sufficient to store the CO2 and wherein the one or more first MOF composition comprises one or more SIFSIX-n-M MOF and wherein M is a metal and n is 2 or 3. Embodiments also describe an apparatus or system for capturing and storing CO2 onboard a vehicle.

Undervisning af tosprogede elever

DEFF Research Database (Denmark)

Horst, Christian

2003-01-01

Artiklen fremdrager hovedresultaterne fra Virginia P. Collier's og Wayne P. Thomas's længdeundersøgelser af tosprogede elever i USA, som formentlig er de mest omfattende undersøgelser af undervisningen af tosprogede elever overhovedet. Resultaterne diskuteres i relation til udviklingen af en...

CO2 Capture and Reuse

International Nuclear Information System (INIS)

Thambimuthu, K.; Gupta, M.; Davison, J.

2003-01-01

CO2 capture and storage including its utilization or reuse presents an opportunity to achieve deep reductions in greenhouse gas emissions from fossil energy use. The development and deployment of this option could significantly assist in meeting a future goal of achieving stabilization of the presently rising atmospheric concentration of greenhouse gases. CO2 capture from process streams is an established concept that has achieved industrial practice. Examples of current applications include the use of primarily, solvent based capture technologies for the recovery of pure CO2 streams for chemical synthesis, for utilization as a food additive, for use as a miscible agent in enhanced oil recovery operations and removal of CO2 as an undesired contaminant from gaseous process streams for the production of fuel gases such as hydrogen and methane. In these applications, the technologies deployed for CO2 capture have focused on gas separation from high purity, high pressure streams and in reducing (or oxygen deficient) environments, where the energy penalties and cost for capture are moderately low. However, application of the same capture technologies for large scale abatement of greenhouse gas emissions from fossil fuel use poses significant challenges in achieving (at comparably low energy penalty and cost) gas separation in large volume, dilute concentration and/or low pressure flue gas streams. This paper will focus on a review of existing commercial methods of CO2 capture and the technology stretch, process integration and energy system pathways needed for their large scale deployment in fossil fueled processes. The assessment of potential capture technologies for the latter purpose will also be based on published literature data that are both 'transparent' and 'systematic' in their evaluation of the overall cost and energy penalties of CO2 capture. In view of the of the fact that many of the existing commercial processes for CO2 capture have seen applications in

A Review of Hazardous Chemical Species Associated with CO2 Capturefrom Coal-Fired Power Plants and Their Potential Fate in CO2 GeologicStorage

Energy Technology Data Exchange (ETDEWEB)

Apps, J.A.

2006-02-23

Conventional coal-burning power plants are major contributors of excess CO2 to the atmospheric inventory. Because such plants are stationary, they are particularly amenable to CO2 capture and disposal by deep injection into confined geologic formations. However, the energy penalty for CO2 separation and compression is steep, and could lead to a 30-40 percent reduction in useable power output. Integrated gas combined cycle (IGCC) plants are thermodynamically more efficient, i.e.,produce less CO2 for a given power output, and are more suitable for CO2 capture. Therefore, if CO2 capture and deep subsurface disposal were to be considered seriously, the preferred approach would be to build replacement IGCC plants with integrated CO2 capture, rather than retrofit existing conventional plants. Coal contains minor quantities of sulfur and nitrogen compounds, which are of concern, as their release into the atmosphere leads to the formation of urban ozone and acid rain, the destruction of stratospheric ozone, and global warming. Coal also contains many trace elements that are potentially hazardous to human health and the environment. During CO2 separation and capture, these constituents could inadvertently contaminate the separated CO2 and be co-injected. The concentrations and speciation of the co-injected contaminants would differ markedly, depending on whether CO2 is captured during the operation of a conventional or an IGCC plant, and the specific nature of the plant design and CO2 separation technology. However, regardless of plant design or separation procedures, most of the hazardous constituents effectively partition into the solid waste residue. This would lead to an approximately two order of magnitude reduction in contaminant concentration compared with that present in the coal. Potential exceptions are Hg in conventional plants, and Hg and possibly Cd, Mo and Pb in IGCC plants. CO2 capture and injection disposal could afford an opportunity to deliberately capture

Brug af alternativ isolering i forbindelse med renovering af ældre etageejendomme

DEFF Research Database (Denmark)

Hansen, Ernst Jan de Place

2003-01-01

Resume af rapport om praktiske erfaringer med brug af alternative isoleringsmaterialer i en renoveringsopgave, udarbejdet af Byfornyelse København m.fl. under Energistyrelsens udviklingsprogram "Miljø- og arbejdsmiljøvenlig isolering"...

Degradation of AF1Q by chaperone-mediated autophagy

International Nuclear Information System (INIS)

Li, Peng; Ji, Min; Lu, Fei; Zhang, Jingru; Li, Huanjie; Cui, Taixing; Li Wang, Xing; Tang, Dongqi; Ji, Chunyan

2014-01-01

AF1Q, a mixed lineage leukemia gene fusion partner, is identified as a poor prognostic biomarker for pediatric acute myeloid leukemia (AML), adult AML with normal cytogenetic and adult myelodysplastic syndrome. AF1Q is highly regulated during hematopoietic progenitor differentiation and development but its regulatory mechanism has not been defined clearly. In the present study, we used pharmacological and genetic approaches to influence chaperone-mediated autophagy (CMA) and explored the degradation mechanism of AF1Q. Pharmacological inhibitors of lysosomal degradation, such as chloroquine, increased AF1Q levels, whereas activators of CMA, including 6-aminonicotinamide and nutrient starvation, decreased AF1Q levels. AF1Q interacts with HSPA8 and LAMP-2A, which are core components of the CMA machinery. Knockdown of HSPA8 or LAMP-2A increased AF1Q protein levels, whereas overexpression showed the opposite effect. Using an amino acid deletion AF1Q mutation plasmid, we identified that AF1Q had a KFERQ-like motif which was recognized by HSPA8 for CMA-dependent proteolysis. In conclusion, we demonstrate for the first time that AF1Q can be degraded in lysosomes by CMA. - Highlights: • Chaperone-mediated autophagy (CMA) is involved in the degradation of AF1Q. • Macroautophagy does not contribute to the AF1Q degradation. • AF1Q has a KFERQ-like motif that is recognized by CMA core components

Degradation of AF1Q by chaperone-mediated autophagy

Energy Technology Data Exchange (ETDEWEB)

Li, Peng; Ji, Min; Lu, Fei; Zhang, Jingru [Department of Hematology, Key Laboratory of Cardiovascular Remodeling and Function Research, Qilu Hospital, Shandong University, Jinan 250012 (China); Li, Huanjie; Cui, Taixing; Li Wang, Xing [Research Center for Cell Therapy, Key Laboratory of Cardiovascular Remodeling and Function Research, Qilu Hospital, Shandong University, Jinan 250012 (China); Tang, Dongqi, E-mail: tangdq@sdu.edu.cn [Research Center for Cell Therapy, Key Laboratory of Cardiovascular Remodeling and Function Research, Qilu Hospital, Shandong University, Jinan 250012 (China); Center for Stem Cell and Regenerative Medicine, The Second Hospital of Shandong University, Jinan 250033 (China); Ji, Chunyan, E-mail: jichunyan@sdu.edu.cn [Department of Hematology, Key Laboratory of Cardiovascular Remodeling and Function Research, Qilu Hospital, Shandong University, Jinan 250012 (China)

2014-09-10

AF1Q, a mixed lineage leukemia gene fusion partner, is identified as a poor prognostic biomarker for pediatric acute myeloid leukemia (AML), adult AML with normal cytogenetic and adult myelodysplastic syndrome. AF1Q is highly regulated during hematopoietic progenitor differentiation and development but its regulatory mechanism has not been defined clearly. In the present study, we used pharmacological and genetic approaches to influence chaperone-mediated autophagy (CMA) and explored the degradation mechanism of AF1Q. Pharmacological inhibitors of lysosomal degradation, such as chloroquine, increased AF1Q levels, whereas activators of CMA, including 6-aminonicotinamide and nutrient starvation, decreased AF1Q levels. AF1Q interacts with HSPA8 and LAMP-2A, which are core components of the CMA machinery. Knockdown of HSPA8 or LAMP-2A increased AF1Q protein levels, whereas overexpression showed the opposite effect. Using an amino acid deletion AF1Q mutation plasmid, we identified that AF1Q had a KFERQ-like motif which was recognized by HSPA8 for CMA-dependent proteolysis. In conclusion, we demonstrate for the first time that AF1Q can be degraded in lysosomes by CMA. - Highlights: • Chaperone-mediated autophagy (CMA) is involved in the degradation of AF1Q. • Macroautophagy does not contribute to the AF1Q degradation. • AF1Q has a KFERQ-like motif that is recognized by CMA core components.

Magnetic structure and spin dynamics of the quasi-one-dimensional spin-chain antiferromagnet BaCo2V2O8

DEFF Research Database (Denmark)

Kawasaki, Yu; Gavilano, Jorge L.; Keller, Lukas

2011-01-01

,0,1), independent of external magnetic fields for fields below a critical value H-c(T). The ordered moments of 2.18 mu(B) per Co ion are aligned along the crystallographic c axis. Within the screw chains, along the c axis, the moments are arranged antiferromagnetically. In the basal planes the spins are arranged......We report a neutron diffraction and muon spin relaxation mu SR study of static and dynamical magnetic properties of BaCo2V2O8, a quasi-one-dimensional spin-chain system. A proposed model for the antiferromagnetic structure includes: a propagation vector (k) over right arrow (AF) = (0...

Effect of amine structure on CO2 capture by polymeric membranes.

Science.gov (United States)

Taniguchi, Ikuo; Kinugasa, Kae; Toyoda, Mariko; Minezaki, Koki

2017-01-01

Poly(amidoamine)s (PAMAMs) incorporated into a cross-linked poly(ethylene glycol) exhibited excellent CO 2 separation properties over H 2 . However, the CO 2 permeability should be increased for practical applications. Monoethanolamine (MEA) used as a CO 2 determining agent in the current CO 2 capture technology at demonstration scale was readily immobilized in poly(vinyl alcohol) (PVA) matrix by solvent casting of aqueous mixture of PVA and the amine. The resulting polymeric membranes can be self-standing with the thickness above 3 μm and the amine fraction less than 80 wt%. The gas permeation properties were examined at 40 °C and under 80% relative humidity. The CO 2 separation performance increased with increase of the amine content in the polymeric membranes. When the amine fraction was 80 wt%, the CO 2 permeability coefficient of MEA containing membrane was 604 barrer with CO 2 selectivity of 58.5 over H 2 , which was much higher than the PAMAM membrane (83.7 barrer and 51.8, respectively) under the same operation conditions. On the other hand, ethylamine (EA) was also incorporated into PVA matrix to form a thin membrane. However, the resulting polymeric membranes exhibited slight CO 2 -selective gas permeation properties. The hydroxyl group of MEA was crucial for high CO 2 separation performance.

Behandling af elmesyge

DEFF Research Database (Denmark)

Thomsen, Iben Margrete; Kristoffersen, Palle

2004-01-01

Ingen midler er p.t. godkendt og dermed lovlige til bekæmpelse af elmesyge i Danmark. Lovprisning af nye behandlinger ses f.eks. på internettet, men dokumentation mangler. Økonomien og nytten ved en kemisk bekæmpelse frem for sanering af syge træer skal afvejes nøje....

CO2 separation from biogas with ceramic membranes

International Nuclear Information System (INIS)

Fassauer, Burkhardt; Richter, Hannes; Schwarz, Bjoern; Reger-Wagner, Norman; Kaemnitz, Susanne; Lubenau, Udo; Mothes, Raimund

2015-01-01

Biogas contains after the production of up to 55% CO 2 . In order to use biogas as a fuel or to feed it into the natural gas network, it must be purified before. Adsorption and scrubbing processes are primarily used technically. Membrane processes offer the advantage of continuous operation and a simple modular and flexible system design, which imply relatively low investment costs and low energy needs. Moreover, membrane systems can be started up and shut down quickly without any problems. Ceramic membranes are characterised by high stability (thermal, chemical, mechanical) and very high flows in comparison to polymeric membranes. [de

Biodegradation of BOD and ammonia-free using bacterial consortium in aerated fixed film bioreactor (AF2B)

Science.gov (United States)

Prayitno, Rulianah, Sri; Saroso, Hadi; Meilany, Diah

2017-06-01

BOD and Ammonia-free (NH3-N) are pollutants of hospital wastewater which often exceed the quality standards. It is because biological processes in wastewater treatment plant (WWTP) have not been effective in degrading BOD and NH3-N. Therefore, a study on factors that influence the biodegradation of BOD and NH3-N by choosing the type of bacteria to improve the mechanisms of biodegradation processes is required. Bacterial consortium is a collection of several types of bacteria obtained from isolation process, which is known to be more effective than a single bacterial in degrading pollutants. On the other hand, AF2B is a type of reactor in wastewater treatment system. The AF2B contains a filter media that has a large surface area so that the biodegradation process of pollutants by microorganism can be improved. The objective of this research is to determine the effect of volume of starter and air supplies on decreasing BOD and NH3-N in hospital wastewater using bacterial consortium in the AF2B on batch process. The research was conducted in three stages: the making of the growth curve of the bacterial consortium, bacterial consortium acclimatization, and hospital wastewater treatment in the AF2B with batch process. The variables used are the volume of starter (65%, 75%, and 85% in volume) and air supplies (2.5, 5, and 7.5 L/min). Meanwhile, the materials used are hospital wastewater, bacterial consortium (Pseudomonas diminuta, Pseudomonas capica, Bacillius sp, and Nitrobacter sp), blower, and AF2B. AF2B is a plastic basin containing a filter media with a wasp-nest shape used as a medium for growing the bacterial consortium. In the process of making the growth curve, a solid form of bacterial consortium was dissolved in sterilized water, then grown in a nutrient broth (NB). Then, shaking and sampling were done at any time to determine the path growth of bacterial consortium. In the acclimatization process, bacterial isolates were grown using hospital wastewater as a

A comparison of cellulosic fuel yields and separated soil-surface CO2 fluxes in maize and prairie biofuel cropping systems

Science.gov (United States)

Nichols, Virginia A.

It has been suggested that strategic incorporation of perennial vegetation into agricultural landscapes could provide ecosystem services while maintaining agricultural productivity. To evaluate potential use of prairie as a Midwestern cellulosic feedstock, we investigated theoretical cellulosic fuel yields, as well as soil-surface carbon dioxide emissions of prairie-based biofuel systems as compared to maize-based systems on fertile soils in Boone County, IA, USA. Investigated systems were: a maize-soybean rotation grown for grain only, continuous maize grown for grain and stover both with and without a winter rye cover crop, and a 31-species reconstructed prairie grown with and without spring nitrogen fertilization for fall-harvested biomass. From 2009-2013, the highest producing system was N-fertilized prairie, averaging 10.4 Mg ha -1 yr-1 above-ground biomass with average harvest removals of 7.8 Mg ha-1 yr-1. The unfertilized prairie produced 7.4 Mg ha-1 yr-1, averaging harvests of 5.3 Mg ha-1 yr-1. Lowest cellulosic biomass harvests were realized from continuous maize systems, averaging 3.5 Mg ha -1 yr-1 when grown with, and 3.7 Mg ha-1 yr-1 when grown without a winter rye cover crop, respectively. Un-fertilized prairie biomass and maize stover had equivalent dietary conversion ratios at 330 g ethanol kg-1 dry biomass, but N-fertilized prairie was lower at 315. Over four years prairie systems averaged 1287 L cellulosic ethanol ha-1 yr-1 more than maize systems, with fertilization increasing prairie ethanol production by 865 L ha-1 yr-1. Harvested biomass accounted for >90% of ethanol yield variation. A major hurdle in carbon cycling studies is the separation of the soil-surface CO2 flux into its respective components. From 2012-2013 we used a shading method to separate soil-surface CO2 resulting from oxidation of soil organic matter and CO2 derived from live-root activity in three systems: unfertilized prairie, N-fertilized prairie, and continuous maize

Energirenovering af Sems Have

DEFF Research Database (Denmark)

Jensen, Søren Østergaard; Rose, Jørgen; Mørck, Ove

Nærværende rapport udgør en del af afrapporteringen af PSO ELFORSK projektet Vejledning for energirenovering af boligblokke til lavenergiklasse 2015 og 2020. Arbejdet har været finansieret af PSO midler via ELFORSK, projekt: 347-023. Formålet med projektet er at udvikle en vejledning for dybtgående...

Depressive patienters oplevelse af at modtage ECT

DEFF Research Database (Denmark)

Jensen, Christine Damsbo

Dette studie handler om, hvordan det opleves for den voksne depressive patient at gennemgå et ECT-behandlingsforløb (electroconvulsive therapy). Formålet med projektet er dels at undersøge, hvordan processen omkring ECT-behandlingen udspiller sig og dels at undersøge patienternes oplevelse......, reaktioner og tanker omkring ECT-behandlingen. Studiet bygger på den eksisterende viden om patienters oplevelse af ECT. Metoden er feltforskning med deltagende observation og etnografisk interview. Dette suppleres af to spørgeskemaer. Der blev inkluderet 8 patienter i undersøgelsen. Analysen udspringer af...... konstruktivistisk epistemiologisk vinkel. Ved en teoristyret analyse fremkom 2 overordnede temaer: Anspændthed og tryghed. Disse temaer blev behandlet i en procesorienteret forståelse af ECT-forløbet. Denne proces bestod af: Betingelser, interaktion og konsekvenser. Diskussionen er en kritisk diskussion af fund og...

Tail gas treatment of sour-SEWGS CO2 product. Public version

Energy Technology Data Exchange (ETDEWEB)

Van Dijk, H.A.J. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

2012-06-15

This literature review covers the technologies suitable for the CO2-H2S separation within the context of CO2 purification of a pre-combustion captured stream intended for storage or reuse. The technologies considered cover existing industrially applied processes, emerging processes as well as processes in development. Several technologies capable of achieving the desired CO2-H2S separation were identified. Among them are liquid scrubbing processes Thiopaq and CrystaSulf producing elemental sulphur, selective oxidation to elemental sulphur such as MODOP or based on novel catalysts and sorbent-based (reactive) separations using low-, medium- or high-temperature (reactive) sorbents. SEWGS stands for Sorption Enhanced Water Gas Shift process.

Midler til lindring af mundtørhed og stimulation af spytsekretion

DEFF Research Database (Denmark)

Dynesen, Anja Weirsøe; Pedersen, Anne Marie Lynge; Jensen, Allan Bardow

2013-01-01

effekt. I relation til risikoen for at udvikle caries, der er forhøjet hos den mundtørre patient, er det dog væsentligt at anbefale produkter uden sukker. Ligesom produktets indhold af syre og dermed det erosive potentiale er af betydning i forhold til udviklingen af dentale erosioner. Systemisk...

Af Upraktiske Grunde

DEFF Research Database (Denmark)

Vaaben, Nana Katrine

2001-01-01

som både Claude Levi-Strauss lægger op til i sine klassiske studier af "den vilde tanke", og som Jean Baudrillard siden har lagt op til i sine analyser af samlere som en slags ekstreme forbrugere, der er i færd med at komplettere deres identitet gennem besiddelser af genstande. Imidlertid tillægger...

Ledelse af projektmyldret

DEFF Research Database (Denmark)

større arbejdsgrupper, og det kan være selvorganiserede store udviklingsprogrammer. Et projekt kører sjældent alene, og derfor er der ikke kun tale om projektledelse, men i lige så høj grad om ledelse af projekter. Ledelse af virksomhedens mylder af projekter er ikke let, og forfatterne gennemgår derfor...

Tema 1: Programmering af robotenheder i grundskolen

Directory of Open Access Journals (Sweden)

Stine Ejsing-Duun

2016-01-01

Full Text Available I denne artikel undersøger vi potentialerne for at lære matematik gennem programmering af robotter. Vi foreslår en model med tre indbyrdes afhængige læringspotentialer, som programmering fordrer. Det omfatter elevens evne til at; (1 tænke i algoritmer, (2 producere viden og artefakter gennem brug af matematik og (3 foretage abstraktion og indkapsling. Programmering er blevet en del af grundskolens læringsmål i flere lande. I Danmark er programmering et læringsmål i forenklede fælles mål for Fysik/Kemi og desuden en del af den nationale undervisningsvejledning for matematik. En analyse af potentialerne i at anvende programmering i forbindelse med disse fag er derfor væsentlig. I denne artikel fokuserer vi på samspillet mellem matematik og programmering gennem litteraturstudier og analyse af empiriske situationer fra undervisning i programmering af LEGO Mindstorms. Teoretisk anvendes den instrumentelle tilgang til teknologi i matematikundervisning. Analysen viser en række måder, hvorpå didaktisk opmærksomhed på epistemisk forhandling kan understøtte læring af matematik gennem programmering.

Recent development of capture of CO2

CERN Document Server

Chavez, Rosa Hilda

2014-01-01

"Recent Technologies in the capture of CO2" provides a comprehensive summary on the latest technologies available to minimize the emission of CO2 from large point sources like fossil-fuel power plants or industrial facilities. This ebook also covers various techniques that could be developed to reduce the amount of CO2 released into the atmosphere. The contents of this book include chapters on oxy-fuel combustion in fluidized beds, gas separation membrane used in post-combustion capture, minimizing energy consumption in CO2 capture processes through process integration, characterization and application of structured packing for CO2 capture, calcium looping technology for CO2 capture and many more. Recent Technologies in capture of CO2 is a valuable resource for graduate students, process engineers and administrative staff looking for real-case analysis of pilot plants. This eBook brings together the research results and professional experiences of the most renowned work groups in the CO2 capture field...

Evaluering af metoder til risikovurdering af kombinationseffekter og etablering af PBTK/TD modeller for pesticider - et ph.d.-projekt

DEFF Research Database (Denmark)