Determination of complex formation constants by phase sensitive alternating current polarography: Cadmium-polymethacrylic acid and cadmium-polygalacturonic acid.

Science.gov (United States)

Garrigosa, Anna Maria; Gusmão, Rui; Ariño, Cristina; Díaz-Cruz, José Manuel; Esteban, Miquel

2007-10-15

The use of phase sensitive alternating current polarography (ACP) for the evaluation of complex formation constants of systems where electrodic adsorption is present has been proposed. The applicability of the technique implies the previous selection of the phase angle where contribution of capacitive current is minimized. This is made using Multivariate Curve Resolution by Alternating Least Squares (MCR-ALS) in the analysis of ACP measurements at different phase angles. The method is checked by the study of the complexation of Cd by polymethacrylic (PMA) and polygalacturonic (PGA) acids, and the optimal phase angles have been ca. -10 degrees for Cd-PMA and ca. -15 degrees for Cd-PGA systems. The goodness of phase sensitive ACP has been demonstrated comparing the determined complex formation constants with those obtained by reverse pulse polarography, a technique that minimizes the electrode adsorption effects on the measured currents.

Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

This action proposes to allow for an additional alternative test method for olefins in gasoline, ASTM D6550-05. The allowance of this additional alternative test method will provide more flexibility to the regulated industry.

A remedial alternative prioritization method

International Nuclear Information System (INIS)

Richter, S.A.; Travis, C.C.

1987-01-01

This study develops and tests a technique for evaluating and prioritizing alternative remedial actions for hazardous waste sites. The method is based on criteria involving risk, benefit and cost, and identifies the most cost-effective solution to a given remedial problem. Four sites on the Department of Energy's Oak Ridge National Laboratory (ORNL) property in Oak Ridge, Tennessee, were used in a case study to develop and test the method. Results of the case study indicate that even if the cap providing in situ containment must be replaced every 10 years, it is a superior alternative to total excavation of the waste sites

Low rank alternating direction method of multipliers reconstruction for MR fingerprinting.

Science.gov (United States)

Assländer, Jakob; Cloos, Martijn A; Knoll, Florian; Sodickson, Daniel K; Hennig, Jürgen; Lattanzi, Riccardo

2018-01-01

The proposed reconstruction framework addresses the reconstruction accuracy, noise propagation and computation time for magnetic resonance fingerprinting. Based on a singular value decomposition of the signal evolution, magnetic resonance fingerprinting is formulated as a low rank (LR) inverse problem in which one image is reconstructed for each singular value under consideration. This LR approximation of the signal evolution reduces the computational burden by reducing the number of Fourier transformations. Also, the LR approximation improves the conditioning of the problem, which is further improved by extending the LR inverse problem to an augmented Lagrangian that is solved by the alternating direction method of multipliers. The root mean square error and the noise propagation are analyzed in simulations. For verification, in vivo examples are provided. The proposed LR alternating direction method of multipliers approach shows a reduced root mean square error compared to the original fingerprinting reconstruction, to a LR approximation alone and to an alternating direction method of multipliers approach without a LR approximation. Incorporating sensitivity encoding allows for further artifact reduction. The proposed reconstruction provides robust convergence, reduced computational burden and improved image quality compared to other magnetic resonance fingerprinting reconstruction approaches evaluated in this study. Magn Reson Med 79:83-96, 2018. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

Alternative Polyadenylation: Methods, Findings, and Impacts

Directory of Open Access Journals (Sweden)

Wei Chen

2017-10-01

Full Text Available Alternative polyadenylation (APA, a phenomenon that RNA molecules with different 3′ ends originate from distinct polyadenylation sites of a single gene, is emerging as a mechanism widely used to regulate gene expression. In the present review, we first summarized various methods prevalently adopted in APA study, mainly focused on the next-generation sequencing (NGS-based techniques specially designed for APA identification, the related bioinformatics methods, and the strategies for APA study in single cells. Then we summarized the main findings and advances so far based on these methods, including the preferences of alternative polyA (pA site, the biological processes involved, and the corresponding consequences. We especially categorized the APA changes discovered so far and discussed their potential functions under given conditions, along with the possible underlying molecular mechanisms. With more in-depth studies on extensive samples, more signatures and functions of APA will be revealed, and its diverse roles will gradually heave in sight. Keywords: Alternative polyadenylation, Next-generation sequencing, 3′UTR, Alternative splicing, Gene regulation

Comparison of the Sensitivity of Three Methods for the Early Diagnosis of Sporotrichosis in Cats.

Science.gov (United States)

Silva, J N; Miranda, L H M; Menezes, R C; Gremião, I D F; Oliveira, R V C; Vieira, S M M; Conceição-Silva, F; Ferreiro, L; Pereira, S A

2018-04-01

Sporotrichosis is caused by species of fungi within the Sporothrix schenckii complex that infect man and animals. In Rio de Janeiro, Brazil, an epidemic has been observed since 1998, with most of the cases being related to transmission from infected cats. Although the definitive diagnosis of feline sporotrichosis is made by fungal culture, cytopathological and histopathological examinations are used routinely, because the long culture period may delay treatment onset. However, alternative methods are desirable in cases of low fungal burden. Immunohistochemistry (IHC) has been described as a sensitive method for diagnosing human and canine sporotrichosis, but there are no reports of its application to cats. The aim of this study was to analyse the sensitivity of cytopathological examination (Quick Panoptic method), histopathology (Grocott silver stain) and anti-Sporothrix IHC by blinded comparisons, using fungal culture as the reference standard. Samples were collected from 184 cats with sporotrichosis that exhibited skin ulcers. The sensitivities of Grocott silver stain, cytopathological examination and IHC were 91.3%, 87.0% and 88.6%, respectively. Grocott silver stain showed the best performance. IHC showed high sensitivity, as did cytopathological examination and these may be considered as alternative methodologies. When the three methods were combined, the diagnosis was established in 180 (97.8%) out of 184 cases. Taken together, these findings indicate the need to implement these methods as routine tools for the early diagnosis of sporotrichosis in cats, notably when fungal culture is not available. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluating clean energy alternatives for Jiangsu, China: An improved multi-criteria decision making method

International Nuclear Information System (INIS)

Zhang, Ling; Zhou, Peng; Newton, Sidney; Fang, Jian-xin; Zhou, De-qun; Zhang, Lu-ping

2015-01-01

Promoting the utilization of clean energy has been identified as one potential solution to addressing environmental pollution and achieving sustainable development in many countries around the world. Evaluating clean energy alternatives includes a requirement to balance multiple conflict criteria, including technology, environment, economy and society, all of which are incommensurate and interdependent. Traditional MCDM (multi-criteria decision making) methods, such as the weighted average method, often fail to aggregate such criteria consistently. In this paper, an improved MCDM method based on fuzzy measure and integral is developed and applied to evaluate four primary clean energy options for Jiangsu Province, China. The results confirm that the preferred clean energy option for Jiangsu is solar photovoltaic, followed by wind, biomass and finally nuclear. A sensitivity analysis is also conducted to evaluate the values of clean energy resources for Jiangsu. The ordered weighted average method is also applied to compare the method mentioned above in our empirical study. The results show that the improved MCDM method provides higher discrimination between alternative clean energy alternatives. - Highlights: • Interactions among evaluation criteria of clean energy resources are taken into account. • An improved multi-criteria decision making (MCDM) method is proposed based on entropy weight method, fuzzy measure and integral. • Clean energy resources of Jiangsu are evaluated with the improved MCDM method, and their ranks are identified.

The Use Of Alternative Methods In Reducing Menopausal ...

African Journals Online (AJOL)

Background: Millions of women experience menopause every year, therefore the aim of this study is to determine the rates of application of alternative methods applied by women in order to reduce their complaints caused by menopause and alternative application methods. Materials and Methods: This study was carried ...

A sensitivity study of an evaluation of alternatives for disposal of INEL low-level waste and low-level mixed waste

International Nuclear Information System (INIS)

Roesener, W.S.; Smith, T.H.; Jorgenson-Waters, M.J.; Sherick, M.J.

1995-01-01

This paper presents insights gained from an informal sensitivity study of an evaluation of disposal alternatives for Idaho National Engineering Laboratory low-level waste and low-level mixed waste. The insights relate to the sensitivity of the alternative rankings to changes in assumptions identified as open-quotes key uncertaintiesclose quotes. The result of the sensitivity study is that significant changes occur in the rankings when selected open-quotes key uncertaintiesclose quotes are varied over reasonable ranges. Three alternatives involving the use of (a) shallow land burial and boreholes or (b) greater-depth burial and boreholes rank high for all cases investigated. The other alternatives rank low in some or all cases

Aptamer-mediated colorimetric method for rapid and sensitive detection of chloramphenicol in food.

Science.gov (United States)

Yan, Chao; Zhang, Jing; Yao, Li; Xue, Feng; Lu, Jianfeng; Li, Baoguang; Chen, Wei

2018-09-15

We report an aptamer-mediated colorimetric method for sensitive detection of chloramphenicol (CAP). The aptamer of CAP is immobilized by the hybridization with pre-immobilized capture probe in the microtiter plate. The horseradish peroxidase (HRP) is covalently attached to the aptamer by the biotin-streptavidin system for signal production. CAP will preferably bind with aptamer due to the high binding affinity, which attributes to the release of aptamer and HRP and thus, affects the optical signal intensity. Quantitative determination of CAP is successfully achieved in the wide range from 0.001 to 1000 ng/mL with detection limit of 0.0031 ng/mL, which is more sensitive than traditional immunoassays. This method is further validated by measuring the recovery of CAP spiked in two different food matrices (honey and fish). The aptamer-mediated colorimetric method can be a useful protocol for rapid and sensitive screening of CAP, and may be used as an alternative means for traditional immunoassays. Copyright © 2018 Elsevier Ltd. All rights reserved.

Sensitivity of Candida albicans to essential oils: are they an alternative to antifungal agents?

Science.gov (United States)

Bona, E; Cantamessa, S; Pavan, M; Novello, G; Massa, N; Rocchetti, A; Berta, G; Gamalero, E

2016-12-01

Candida albicans is an important opportunistic pathogen, responsible for the majority of yeast infections in humans. Essential oils, extracted from aromatic plants, are well-known antimicrobial agents, characterized by a broad spectrum of activities, including antifungal properties. The aim of this work was to assess the sensitivity of 30 different vaginal isolated strains of C. albicans to 12 essential oils, compared to the three main used drugs (clotrimazole, fluconazole and itraconazole). Thirty strains of C. albicans were isolated from vaginal swab on CHROMagar ™ Candida. The agar disc diffusion method was employed to determine the sensitivity to the essential oils. The antifungal activity of the essential oils and antifungal drugs (clotrimazole, itraconazole and fluconazole) were investigated using a microdilution method. Transmission and scanning electron microscopy analyses were performed to get a deep inside on cellular damages. Mint, basil, lavender, tea tree oil, winter savory and oregano essential oils inhibited both the growth and the activity of C. albicans more efficiently than clotrimazole. Damages induced by essential oils at the cellular level were stronger than those caused by clotrimazole. Candida albicans is more sensitive to different essential oils compared to the main used drugs. Moreover, the essential oil affected mainly the cell wall and the membranes of the yeast. The results of this work support the research for new alternatives or complementary therapies against vaginal candidiasis. © 2016 The Society for Applied Microbiology.

30 CFR 250.1504 - May I use alternative training methods?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false May I use alternative training methods? 250... Safety Training § 250.1504 May I use alternative training methods? You may use alternative training methods. These methods may include computer-based learning, films, or their equivalents. This training...

Strategies for cost-effective carbon reductions: A sensitivity analysis of alternative scenarios

International Nuclear Information System (INIS)

Gumerman, Etan; Koomey, Jonathan G.; Brown, Marilyn

2001-01-01

Analyses of alternative futures often present results for a limited set of scenarios, with little if any sensitivity analysis to identify the factors affecting the scenario results. This approach creates an artificial impression of certainty associated with the scenarios considered, and inhibits understanding of the underlying forces. This paper summarizes the economic and carbon savings sensitivity analysis completed for the Scenarios for a Clean Energy Future study (IWG, 2000). Its 19 sensitivity cases provide insight into the costs and carbon-reduction impacts of a carbon permit trading system, demand-side efficiency programs, and supply-side policies. Impacts under different natural gas and oil price trajectories are also examined. The results provide compelling evidence that policy opportunities exist to reduce carbon emissions and save society money

Fast acquisition of multidimensional NMR spectra of solids and mesophases using alternative sampling methods.

Science.gov (United States)

Lesot, Philippe; Kazimierczuk, Krzysztof; Trébosc, Julien; Amoureux, Jean-Paul; Lafon, Olivier

2015-11-01

Unique information about the atom-level structure and dynamics of solids and mesophases can be obtained by the use of multidimensional nuclear magnetic resonance (NMR) experiments. Nevertheless, the acquisition of these experiments often requires long acquisition times. We review here alternative sampling methods, which have been proposed to circumvent this issue in the case of solids and mesophases. Compared to the spectra of solutions, those of solids and mesophases present some specificities because they usually display lower signal-to-noise ratios, non-Lorentzian line shapes, lower spectral resolutions and wider spectral widths. We highlight herein the advantages and limitations of these alternative sampling methods. A first route to accelerate the acquisition time of multidimensional NMR spectra consists in the use of sparse sampling schemes, such as truncated, radial or random sampling ones. These sparsely sampled datasets are generally processed by reconstruction methods differing from the Discrete Fourier Transform (DFT). A host of non-DFT methods have been applied for solids and mesophases, including the G-matrix Fourier transform, the linear least-square procedures, the covariance transform, the maximum entropy and the compressed sensing. A second class of alternative sampling consists in departing from the Jeener paradigm for multidimensional NMR experiments. These non-Jeener methods include Hadamard spectroscopy as well as spatial or orientational encoding of the evolution frequencies. The increasing number of high field NMR magnets and the development of techniques to enhance NMR sensitivity will contribute to widen the use of these alternative sampling methods for the study of solids and mesophases in the coming years. Copyright © 2015 John Wiley & Sons, Ltd.

Economic analysis of alternative LLW disposal methods

International Nuclear Information System (INIS)

Foutes, C.E.

1987-01-01

The Environmental Protection Agency (EPA) has evaluated the costs and benefits of alternative disposal technologies as part of its program to develop generally applicable environmental standards for the land disposal of low-level radioactive waste (LLW). Costs, population health effects and Critical Population Group (CPG) exposures resulting from alternative waste treatment and disposal methods were developed and input into the analysis. The cost-effectiveness analysis took into account a number of waste streams, hydrogeologic and climatic region settings, and waste treatment and disposal methods. Total costs of each level of a standard included costs for packaging, processing, transportation, and burial of waste. Benefits are defined in terms of reductions in the general population health risk (expected fatal cancers and genetic effects) evaluated over 10,000 years. A cost-effectiveness ratio, was calculated for each alternative standard. This paper describes the alternatives considered and preliminary results of the cost-effectiveness analysis

Alternative Therapy of Animals – Homeopathy and Other Alternative Methods of Therapy

Directory of Open Access Journals (Sweden)

Løken Torleiv

2002-03-01

Full Text Available Alternative therapy of animals is described, in the meaning of alternatives to veterinary therapy traditionally accepted by veterinary faculties and schools and included in their curricula. Alternative therapy composes of different disciplines, of which homeopathy is emphasised in this presentation. Information is given on the use and interest of such therapy among veterinarians and animal owners. Homeopathy as other alternative therapies, may offer great advances, if they induce any effect. Some of the disciplines are based on a scientifically accepted documentation. Others, and homeopathy in particular, are missing such a documentation of effect. The justification of including alternative therapy in treating animals is discussed. Research in alternative therapy of animals is greatly needed, in particular to evaluate therapeutic methods which are in extensive use without any documented effect. An ongoing research project in Norway on the effect of homeopathic treatment of mastitis in cows is shortly presented.

Alternatives to the gravimetric method for quantification of diesel particulate matter near the lower level of detection.

Science.gov (United States)

Swanson, Jacob; Kittelson, David; Pui, David; Watts, Winthrop

2010-10-01

This paper is part of the Journal of the Air & Waste Management Association's 2010 special issue on combustion aerosol measurements. The issue is a combination of papers that synthesize and evaluate ideas and perspectives that were presented by experts at a series of workshops sponsored by the Coordinating Research Council that aimed to evaluate the current and future status of diesel particulate matter (DPM) measurement. Measurement of DPM is a complex issue with many stakeholders, including air quality management and enforcement agencies, engine manufacturers, health experts, and climatologists. Adoption of the U.S. Environmental Protection Agency 2007 heavy-duty engine DPM standards posed a unique challenge to engine manufacturers. The new standards reduced DPM emissions to the point that improvements to the gravimetric method were required to increase the accuracy and the sensitivity of the measurement. Despite these improvements, the method still has shortcomings. The objectives of this paper are to review the physical and chemical properties of DPM that make gravimetric measurement difficult at very low concentrations and to review alternative metrics and methods that are potentially more accurate, sensitive, and specific. Particle volatility, size, surface area, and number metrics are considered, as well as methods to quantify them. Although the authors believe that an alternative method is required to meet the needs of engine manufacturers, the methods reviewed in the paper are applicable to other areas where the gravimetric method detection limit is approached and greater accuracy and sensitivity are required. The paper concludes by suggesting a method to measure active surface area, combined with a method to separate semi-volatile and solid fractions to further increase the specificity of the measurement, has potential for reducing the lower detection limit of DPM and enabling engine manufacturers to reduce DPM emissions in the future.

Non-animal methods to predict skin sensitization (II): an assessment of defined approaches *.

Science.gov (United States)

Kleinstreuer, Nicole C; Hoffmann, Sebastian; Alépée, Nathalie; Allen, David; Ashikaga, Takao; Casey, Warren; Clouet, Elodie; Cluzel, Magalie; Desprez, Bertrand; Gellatly, Nichola; Göbel, Carsten; Kern, Petra S; Klaric, Martina; Kühnl, Jochen; Martinozzi-Teissier, Silvia; Mewes, Karsten; Miyazawa, Masaaki; Strickland, Judy; van Vliet, Erwin; Zang, Qingda; Petersohn, Dirk

2018-05-01

Skin sensitization is a toxicity endpoint of widespread concern, for which the mechanistic understanding and concurrent necessity for non-animal testing approaches have evolved to a critical juncture, with many available options for predicting sensitization without using animals. Cosmetics Europe and the National Toxicology Program Interagency Center for the Evaluation of Alternative Toxicological Methods collaborated to analyze the performance of multiple non-animal data integration approaches for the skin sensitization safety assessment of cosmetics ingredients. The Cosmetics Europe Skin Tolerance Task Force (STTF) collected and generated data on 128 substances in multiple in vitro and in chemico skin sensitization assays selected based on a systematic assessment by the STTF. These assays, together with certain in silico predictions, are key components of various non-animal testing strategies that have been submitted to the Organization for Economic Cooperation and Development as case studies for skin sensitization. Curated murine local lymph node assay (LLNA) and human skin sensitization data were used to evaluate the performance of six defined approaches, comprising eight non-animal testing strategies, for both hazard and potency characterization. Defined approaches examined included consensus methods, artificial neural networks, support vector machine models, Bayesian networks, and decision trees, most of which were reproduced using open source software tools. Multiple non-animal testing strategies incorporating in vitro, in chemico, and in silico inputs demonstrated equivalent or superior performance to the LLNA when compared to both animal and human data for skin sensitization.

Comparison of increased venous contrast in ischemic stroke using phase-sensitive MR imaging with perfusion changes on flow-sensitive alternating inversion recovery at 3 Tesla

International Nuclear Information System (INIS)

Yamashita, Eijiro; Kanasaki, Yoshiko; Fujii, Shinya; Ogawa, Toshihide; Tanaka, Takuro; Hirata, Yoshiharu

2011-01-01

Background Increased venous contrast in ischemic stroke using susceptibility-weighted imaging has been widely reported, although few reports have compared increased venous contrast areas with perfusion change areas. Purpose To compare venous contrast on phase-sensitive MR images (PSI) with perfusion change on flow-sensitive alternating inversion recovery (FAIR) images, and to discuss the clinical use of PSI in ischemic stroke. Material and Methods Thirty patients with clinically suspected acute infarction of the middle cerebral artery (MCA) territory within 7 days of onset were evaluated. Phase-sensitive imaging (PSI), flow-sensitive alternating inversion recovery (FAIR), diffusion-weighted imaging (DWI) and magnetic resonance angiography (MRA) were obtained using 3 Tesla scanner. Two neuroradiologists independently reviewed the MR images, as well as the PSI, DWI, and FAIR images. They were blinded to the clinical data and to each other's findings. The abnormal area of each image was ultimately identified after both neuroradiologists reached consensus. We analyzed areas of increased venous contrast on PSI, perfusion changes on FAIR images and signal changes on DWI for each case. Results Venous contrast increased on PSI and hypoperfusion was evident on FAIR images from 22 of the 30 patients (73%). The distribution of the increased venous contrast was the same as that of the hypoperfused areas on FAIR images in 16 of these 22. The extent of these lesions was larger than that of lesions visualized by on DWI in 18 of the 22 patients. Hypointense signals reflecting hemorrhage and no increased venous contrast on PSI and hyperperfusion on FAIR images were found in six of the remaining eight patients (20%). Findings on PSI were normal and hypoperfusion areas were absent on FAIR images of two patients (7%). Conclusion Increased venous contrast on PSI might serve as an index of misery perfusion and provide useful information

Economic analysis of alternative LLW disposal methods

International Nuclear Information System (INIS)

Foutes, C.E.; Queenan, C.J. III

1987-01-01

The Environmental Protection Agency (EPA) has evaluated the costs and benefits of alternative disposal technologies as part of its program to develop generally applicable environmental standards for the land disposal of low-level radioactive waste (LLW). Costs, population health effects and Critical Population Group (CPG) exposures resulting from alternative waste treatment and disposal methods were evaluated both in absolute terms and also relative to a base case (current practice). Incremental costs of the standard included costs for packaging, processing, transportation, and burial of waste. Benefits are defined in terms of reductions in the general population health risk (expected fatal cancers and genetic effects) evaluated over 10,000 years. A cost-effectiveness ratio, defined as the incremental cost per avoided health effect, was calculated for each alternative standard. The cost-effectiveness analysis took into account a number of waste streams, hydrogeologic and climatic region settings, and waste treatment and disposal methods. This paper describes the alternatives considered and preliminary results of the cost-effectiveness analysis. 15 references, 7 figures, 3 tables

A new 3D reconstituted human corneal epithelium model as an alternative method for the eye irritation test.

Science.gov (United States)

Jung, Kyoung-Mi; Lee, Su-Hyon; Ryu, Yang-Hwan; Jang, Won-Hee; Jung, Haeng-Sun; Han, Ju-Hee; Seok, Seung-Hyeok; Park, Jae-Hak; Son, Youngsook; Park, Young-Ho; Lim, Kyung-Min

2011-02-01

Many efforts are being made to develop new alternative in vitro test methods for the eye irritation test. Here we report a new reconstructed human corneal epithelial model (MCTT HCE model) prepared from primary-cultured human limbal epithelial cells as a new alternative in vitro eye irritation test method. In histological and immunohistochemical observation, MCTT HCE model displayed a morphology and biomarker expressions similar to intact human cornea. Moreover, the barrier function was well preserved as measured by high transepithelial electrical resistance, effective time-50 for Triton X-100, and corneal thickness. To employ the model as a new alternative method for eye irritation test, protocol refinement was performed and optimum assay condition was determined including treatment time, treatment volume, post-incubation time and rinsing method. Using the refined protocol, 25 reference chemicals with known eye irritation potentials were tested. With the viability cut-off value at 50%, chemicals were classified to irritant or non-irritant. When compared with GHS classification, the MCTT HCE model showed the accuracy of 88%, sensitivity of 100% and specificity of 77%. These results suggest that the MCTT HCE model might be useful as a new alternative eye irritation test method. Copyright © 2010 Elsevier Ltd. All rights reserved.

Quantitative determination of enterococci in water using an alternative chromogenic method

International Nuclear Information System (INIS)

Diaz Perez, Marilyn; Zhurbenko, Raisa; Lobaina Rodriguez, Tamara

2014-01-01

Water quality control is essential for the protection of human health and biodiversity in the aquatic environment. For this purpose, several microorganisms are used as indicators of fecal contamination. Among them are enterococci, which are considered to be good indicators, since they survive for a longer time in adverse natural conditions. Water samples were collected from three different sources to determine their quality. The samples were assayed in parallel with the two methodologies (alternative and reference) using the membrane filtration technique. The following parameters were determined to evaluate the performance of the methods: sensitivity, specificity, accuracy, percentage of false positives, percentage of false negatives, kappa index. The first three parameters were estimated for both methods before and after confirmation by biochemical testing. Results were analyzed statistically based on the main criteria defined by ISO standards 16140 and 177994

77 FR 8865 - Recent Postings of Broadly Applicable Alternative Test Methods

Science.gov (United States)

2012-02-15

... Applicable Alternative Test Methods AGENCY: Environmental Protection Agency (EPA). ACTION: Notice of availability. SUMMARY: This notice announces the broadly applicable alternative test method approval decisions... INFORMATION CONTACT: An electronic copy of each alternative test method approval document is available on the...

Feasibility of Incorporating Alternative Teaching Methods into Clinical Clerkships.

Science.gov (United States)

Berman, Judith; And Others

1990-01-01

A study investigated the effectiveness of computer-assisted instruction, interactive video, and videotapes as alternative methods of instruction in clinical clerkship modules on diabetes and hypertension. The 17 participants were more interested in balancing time between patient contact and alternative teaching methods and had better knowledge,…

The use of carbon black-TiO2 composite prepared using solid state method as counter electrode and E. conferta as sensitizer for dye-sensitized solar cell (DSSC) applications

Science.gov (United States)

Jaafar, Hidayani; Ahmad, Zainal Arifin; Ain, Mohd Fadzil

2018-05-01

In this paper, counter electrodes based on carbon black (CB)-TiO2 composite are proposed as a cost-effective alternative to conventional Pt counter electrodes used in dye-sensitized solar cell (DSSC) applications. CB-TiO2 composite counter electrodes with different weight percentages of CB were prepared using the solid state method and coated onto fluorine-doped tin oxide (FTO) glass using doctor blade method while Eleiodoxa conferta (E. conferta) and Nb-doped TiO2 were used as sensitizer and photoanode, respectively, with electrolyte containing I-/I-3 redox couple. The experimental results revealed that the CB-TiO2 composite influenced the photovoltaic performance by enhancing the electrocatalytic activity. As the amount of CB increased, the catalytic activity improved due to the increase in surface area which then led to low charge-transfer resistance (RCT) at the electrolyte/CB electrode interface. Due to the use of the modified photoanode together with natural dye sensitizers, the counter electrode based on 15 wt% CB-TiO2 composite was able to produce the highest energy conversion efficiency (2.5%) making it a viable alternative counter electrode.

46 CFR 50.20-30 - Alternative materials or methods of construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Alternative materials or methods of construction. 50.20... ENGINEERING GENERAL PROVISIONS Plan Submittal and Approval § 50.20-30 Alternative materials or methods of construction. (a) When new or alternative procedures, designs, or methods of construction are submitted for...

Efficiencies of Dye-Sensitized Solar Cells using Ferritin-Encapsulated Quantum Dots with Various Staining Methods

Science.gov (United States)

Perez, Luis

Dye-sensitized solar cells (DSSC) have the potential to replace traditional and cost-inefficient crystalline silicon or ruthenium solar cells. This can only be accomplished by optimizing DSSC's energy efficiency. One of the major components in a dye-sensitized solar cell is the porous layer of titanium dioxide. This layer is coated with a molecular dye that absorbs sunlight. The research conducted for this paper focuses on the different methods used to dye the porous TiO2 layer with ferritin-encapsulated quantum dots. Multiple anodes were dyed using a method known as SILAR which involves deposition through alternate immersion in two different solutions. The efficiencies of DSSCs with ferritin-encapsulated lead sulfide dye deposited using SILAR were subsequently compared against the efficiencies produced by cells using the traditional immersion method. It was concluded that both methods resulted in similar efficiencies (? .074%) however, the SILAR method dyed the TiO2 coating significantly faster than the immersion method. On a related note, our experiments concluded that conducting 2 SILAR cycles yields the highest possible efficiency for this particular binding method. National Science Foundation.

Evaluation of Forklift Alternatives with KEMIRA-M Method

Directory of Open Access Journals (Sweden)

Gizem SARIÇALI

2017-01-01

Full Text Available Businesses generally uses forklifts for lifting, stacking and transporting to the desired location of heavy loads in case of human power is not enough. It is important to select suitable forklifts for the physical conditions of the warehouses in order to ensure the active use of them. In storage, the selection of the appropriate forklift for physical conditions of the warehouse is important to use warehouses effectively. In this study, KEMIRA-M (KEmeny Median Indicator Rank Accordance-Modified method, which is a new Multi-Criteria Decision Making (MCDM method, was used to evaluate forklift alternatives to be used in storage and to determine the most appropriate forklift for the textile company. This method does not require much initial information, so it can be used to determine the weights of the criteria and to select the most appropriate alternative. As a result of the study, forklift alternative that will best meet the needs of the textile company was determined with KEMIRA-M method, by this way the company has been aided during the decision process.

A Modified Alternating Direction Method for Variational Inequality Problems

International Nuclear Information System (INIS)

Han, D.

2002-01-01

The alternating direction method is an attractive method for solving large-scale variational inequality problems whenever the subproblems can be solved efficiently. However, the subproblems are still variational inequality problems, which are as structurally difficult to solve as the original one. To overcome this disadvantage, in this paper we propose a new alternating direction method for solving a class of nonlinear monotone variational inequality problems. In each iteration the method just makes an orthogonal projection to a simple set and some function evaluations. We report some preliminary computational results to illustrate the efficiency of the method

Evaluation of alternative public transportation systems in Izmit urban transportation via axiomatic design method

Directory of Open Access Journals (Sweden)

Gülşen AKMAN

2016-02-01

Full Text Available In the world and in our country, most of urban transportation is performed by public transportation. Public transportation is a system which provides transportation easiness and opportunity to people, not to vehicles. Therefore, giving priority to public transportation system is necessary in organizing urban transportation. In this study, in order to reduce traffic intensity and to facilitate passenger transportation in Izmit urban transportation, It is tried to determine appropriate public transportation system. For this, firstly, alternatives which could be used for public transportation were determined. These alternatives are metro, metrobus, tram, light rail system and monorail. Afterwards, the variables affecting decision making about public transportation were determined. These variables are cost, transportation line features, vehicle characteristics, sensitivity to environment and customer satisfaction. Lastly, most appropriate public transportation system is proposed by using the axiomatic design method. As a result, light trail system and metrobus are determined as the most appropriate alternatives for Izmit public transportation system.Keywords: Urban transportation, Multi criteria decision making, Axiomatic design

49 CFR Appendix B to Part 178 - Alternative Leakproofness Test Methods

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Alternative Leakproofness Test Methods B Appendix... FOR PACKAGINGS Pt. 178, App. B Appendix B to Part 178—Alternative Leakproofness Test Methods In addition to the method prescribed in § 178.604 of this subchapter, the following leakproofness test methods...

Community Perspective of Alternative Methods of keeping ...

African Journals Online (AJOL)

UNIBEN

methods of keeping childhood immunization records based on community's .... An alternative home-based record keeping ... coded before computer entry. Data was managed using the Statistical ..... encounter and also work to ensure accurate.

Calculation of mixed mode stress intensity factors using an alternating method

International Nuclear Information System (INIS)

Sakai, Takayuki

1999-01-01

In this study, mixed mode stress intensity factors (K I and K II ) of a square plate with a notch were calculated using a finite element alternating method. The obtained results were compared with the ones by a finite element method, and it was shown that the finite element alternating method can accurately estimate mixed mode stress intensity factors. Then, using this finite element alternating method, mixed mode stress intensity factors were calculated as changing the size and position of the notch, and its simplified equations were proposed. (author)

48 CFR 6302.30 - Alternative dispute resolution methods (Rule 30).

Science.gov (United States)

2010-10-01

... TRANSPORTATION BOARD OF CONTRACT APPEALS RULES OF PROCEDURE 6302.30 Alternative dispute resolution methods (Rule... Alternative Dispute Resolution (ADR): Settlement Judges and Mini-Trials. These procedures are designed to... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Alternative dispute...

NRC perspective on alternative disposal methods

International Nuclear Information System (INIS)

Pittiglio, C.L.; Tokar, M.

1987-01-01

In this paper is discussed an NRC staff strategy for the development of technical criteria and procedures for the licensing of various alternatives for disposal of low-level radioactive waste. Steps taken by the staff to identify viable alternative disposal methods and to comply with the requirements of the Low-Level Radioactive Waste Policy Amendments Act (LLRWPAA) of 1985 are also discussed. The strategy proposed by the NRC staff is to focus efforts in FY 87 on alternative concepts that incorporate concrete materials with soil or rock cover (e.g., below ground vaults and earth-mounded concrete bunkers), which several State and State Compacts have identified as preferred disposal options. While the NRC staff believes that other options, such as above ground vaults and mined cavities, are workable and licensable, the staff also believes, for reasons addressed in the paper, that it is in the best interest of the industry and the public to encourage standardization and to focus limited resources on a manageable number of alternative options. Therefore, guidance on above ground vaults, which are susceptible to long-term materials degradation due to climatological effects, and mined cavities, which represent a significant departure from the current experience base for low-level radioactive waste disposal, will receive minimal attention. 6 references

The American Heart Association Scientific Statement on salt sensitivity of blood pressure: Prompting consideration of alternative conceptual frameworks for the pathogenesis of salt sensitivity?

Science.gov (United States)

Kurtz, Theodore W; DiCarlo, Stephen E; Pravenec, Michal; Morris, R Curtis

2017-11-01

: Recently, the American Heart Association (AHA) published a scientific statement on salt sensitivity of blood pressure which emphasized a decades old conceptual framework for the pathogenesis of this common disorder. Here we examine the extent to which the conceptual framework for salt sensitivity emphasized in the AHA Statement accommodates contemporary findings and views of the broader scientific community on the pathogenesis of salt sensitivity. In addition, we highlight alternative conceptual frameworks and important contemporary theories of salt sensitivity that are little discussed in the AHA Statement. We suggest that greater consideration of conceptual frameworks and theories for salt sensitivity beyond those emphasized in the AHA Statement may help to advance understanding of the pathogenesis of salt-induced increases in blood pressure and, in consequence, may lead to improved approaches to preventing and treating this common disorder.

Novel Method for Sizing Metallic Bottom Crack Depth Using Multi-frequency Alternating Current Potential Drop Technique

OpenAIRE

Li Yuting; Gan Fangji; Wan Zhengjun; Liao Junbi; Li Wenqiang

2015-01-01

Potential drop techniques are of two types: the direct current potential drop (DCPD) technique and alternating current potential drop (ACPD) technique, and both of them are used in nondestructive testing. ACPD, as a kind of valid method in sizing metal cracks, has been applied to evaluate metal structures. However, our review of most available approaches revealed that some improvements can be done in measuring depth of metal bottom crack by means of ACPD, such as accuracy and sensitivity of s...

Alternative methods for toxicity assessments in fish: comparison of the fish embryo toxicity and the larval growth and survival tests in zebrafish and fathead minnows.

Science.gov (United States)

Jeffries, Marlo K Sellin; Stultz, Amy E; Smith, Austin W; Rawlings, Jane M; Belanger, Scott E; Oris, James T

2014-11-01

An increased demand for chemical toxicity evaluations has resulted in the need for alternative testing strategies that address animal welfare concerns. The fish embryo toxicity (FET) test developed for zebrafish (Danio rerio) is one such alternative, and the application of the FET test to other species such as the fathead minnow (Pimephales promelas) has been proposed. In the present study, the performances of the FET test and the larval growth and survival (LGS; a standard toxicity testing method) test in zebrafish and fathead minnows were evaluated. This required that testing methods for the fathead minnow FET and zebrafish LGS tests be harmonized with existing test methods and that the performance of these testing strategies be evaluated by comparing the median lethal concentrations of 2 reference toxicants, 3,4-dicholoraniline and ammonia, obtained via each of the test types. The results showed that procedures for the zebrafish FET test can be adapted and applied to the fathead minnow. Differences in test sensitivity were observed for 3,4-dicholoraniline but not ammonia; therefore, conclusions regarding which test types offer the least or most sensitivity could not be made. Overall, these results show that the fathead minnow FET test has potential as an alternative toxicity testing strategy and that further analysis with other toxicants is warranted in an effort to better characterize the sensitivity and feasibility of this testing strategy. © 2014 SETAC.

High School Graduation Rates:Alternative Methods and Implications

Directory of Open Access Journals (Sweden)

Jing Miao

2004-10-01

Full Text Available The No Child Left Behind Act has brought great attention to the high school graduation rate as one of the mandatory accountability measures for public school systems. However, there is no consensus on how to calculate the high school graduation rate given the lack of longitudinal databases that track individual students. This study reviews literature on and practices in reporting high school graduation rates, compares graduation rate estimates yielded from alternative methods, and estimates discrepancies between alternative results at national, state, and state ethnic group levels. Despite the graduation rate method used, results indicate that high school graduation rates in the U.S. have been declining in recent years and that graduation rates for black and Hispanic students lag substantially behind those of white students. As to graduation rate method preferred, this study found no evidence that the conceptually more complex methods yield more accurate or valid graduation rate estimates than the simpler methods.

SNR-optimized phase-sensitive dual-acquisition turbo spin echo imaging: a fast alternative to FLAIR.

Science.gov (United States)

Lee, Hyunyeol; Park, Jaeseok

2013-07-01

Phase-sensitive dual-acquisition single-slab three-dimensional turbo spin echo imaging was recently introduced, producing high-resolution isotropic cerebrospinal fluid attenuated brain images without long inversion recovery preparation. Despite the advantages, the weighted-averaging-based technique suffers from noise amplification resulting from different levels of cerebrospinal fluid signal modulations over the two acquisitions. The purpose of this work is to develop a signal-to-noise ratio-optimized version of the phase-sensitive dual-acquisition single-slab three-dimensional turbo spin echo. Variable refocusing flip angles in the first acquisition are calculated using a three-step prescribed signal evolution while those in the second acquisition are calculated using a two-step pseudo-steady state signal transition with a high flip-angle pseudo-steady state at a later portion of the echo train, balancing the levels of cerebrospinal fluid signals in both the acquisitions. Low spatial frequency signals are sampled during the high flip-angle pseudo-steady state to further suppress noise. Numerical simulations of the Bloch equations were performed to evaluate signal evolutions of brain tissues along the echo train and optimize imaging parameters. In vivo studies demonstrate that compared with conventional phase-sensitive dual-acquisition single-slab three-dimensional turbo spin echo, the proposed optimization yields 74% increase in apparent signal-to-noise ratio for gray matter and 32% decrease in imaging time. The proposed method can be a potential alternative to conventional fluid-attenuated imaging. Copyright © 2012 Wiley Periodicals, Inc.

An alternative method for Plasmodium culture synchronization.

Science.gov (United States)

Lelièvre, J; Berry, A; Benoit-Vical, F

2005-03-01

Since the synchronization of Plasmodium falciparum has become an essential tool in research, we have investigated the use of a commercial gelatine solution, Plasmion, to replace Plasmagel, which is now difficult to obtain. This method also avoids the use of techniques based on Percoll-glucose gradients. The Plasmion-based technique proved to be a good method and could become an alternative to Plasmagel.

Record-keeping as an Alternative Method οf Assessment

Directory of Open Access Journals (Sweden)

Androniki Kouvdou

2010-02-01

Full Text Available The basic topic of this chapter is the description of an alternative method of assessment which supplements traditional objective techniques (i.e. testing, while counterbalancing their limitations. This alternative method, known as ‘record-keeping’, involves the systematic collection and recording of information about learner progress and aims at providing a more complete and valid formative assessment of their developmental abilities in specified areas. More particularly, this chapter presents a small-scale case study, which was carried out in the sixth grade of a primary school and lasted three months. The subjects of this case study were four twelve-year-old learners and its purpose was to investigate the potential of ‘record-keeping’ as an alternative method of assessing oracy skills in the foreign language. The data that derived from the case study reinforce the usefulness and validity of the particular method of assessment. The goals of the experimental assessment design, which entailed the recording and gradual development of learner oracy skills as well as the enhancement of motivation and awareness of their relevant sub-skills, were accomplished to a considerable degree. Additionally, the learners responded positively to the implemented assessment project, while being actively involved in it, which further substantiates its effectiveness. Alternative assessment, however, is a large area, whose full potential of implementation calls for further investigation.

Alternatives to animal testing: research, trends, validation, regulatory acceptance.

Science.gov (United States)

Huggins, Jane

2003-01-01

Current trends and issues in the development of alternatives to the use of animals in biomedical experimentation are discussed in this position paper. Eight topics are considered and include refinement of acute toxicity assays; eye corrosion/irritation alternatives; skin corrosion/irritation alternatives; contact sensitization alternatives; developmental/reproductive testing alternatives; genetic engineering (transgenic) assays; toxicogenomics; and validation of alternative methods. The discussion of refinement of acute toxicity assays is focused primarily on developments with regard to reduction of the number of animals used in the LD(50) assay. However, the substitution of humane endpoints such as clinical signs of toxicity for lethality in these assays is also evaluated. Alternative assays for eye corrosion/irritation as well as those for skin corrosion/irritation are described with particular attention paid to the outcomes, both successful and unsuccessful, of several validation efforts. Alternative assays for contact sensitization and developmental/reproductive toxicity are presented as examples of methods designed for the examination of interactions between toxins and somewhat more complex physiological systems. Moreover, genetic engineering and toxicogenomics are discussed with an eye toward the future of biological experimentation in general. The implications of gene manipulation for research animals, specifically, are also examined. Finally, validation methods are investigated as to their effectiveness, or lack thereof, and suggestions for their standardization and improvement, as well as implementation are reviewed.

LLNA variability: An essential ingredient for a comprehensive assessment of non-animal skin sensitization test methods and strategies.

Science.gov (United States)

Hoffmann, Sebastian

2015-01-01

The development of non-animal skin sensitization test methods and strategies is quickly progressing. Either individually or in combination, the predictive capacity is usually described in comparison to local lymph node assay (LLNA) results. In this process the important lesson from other endpoints, such as skin or eye irritation, to account for variability reference test results - here the LLNA - has not yet been fully acknowledged. In order to provide assessors as well as method and strategy developers with appropriate estimates, we investigated the variability of EC3 values from repeated substance testing using the publicly available NICEATM (NTP Interagency Center for the Evaluation of Alternative Toxicological Methods) LLNA database. Repeat experiments for more than 60 substances were analyzed - once taking the vehicle into account and once combining data over all vehicles. In general, variability was higher when different vehicles were used. In terms of skin sensitization potential, i.e., discriminating sensitizer from non-sensitizers, the false positive rate ranged from 14-20%, while the false negative rate was 4-5%. In terms of skin sensitization potency, the rate to assign a substance to the next higher or next lower potency class was approx.10-15%. In addition, general estimates for EC3 variability are provided that can be used for modelling purposes. With our analysis we stress the importance of considering the LLNA variability in the assessment of skin sensitization test methods and strategies and provide estimates thereof.

Uncertainty and Sensitivity of Alternative Rn-222 Flux Density Models Used in Performance Assessment

International Nuclear Information System (INIS)

Greg J. Shott, Vefa Yucel, Lloyd Desotell Non-Nstec Authors: G. Pyles and Jon Carilli

2007-01-01

Performance assessments for the Area 5 Radioactive Waste Management Site on the Nevada Test Site have used three different mathematical models to estimate Rn-222 flux density. This study describes the performance, uncertainty, and sensitivity of the three models which include the U.S. Nuclear Regulatory Commission Regulatory Guide 3.64 analytical method and two numerical methods. The uncertainty of each model was determined by Monte Carlo simulation using Latin hypercube sampling. The global sensitivity was investigated using Morris one-at-time screening method, sample-based correlation and regression methods, the variance-based extended Fourier amplitude sensitivity test, and Sobol's sensitivity indices. The models were found to produce similar estimates of the mean and median flux density, but to have different uncertainties and sensitivities. When the Rn-222 effective diffusion coefficient was estimated using five different published predictive models, the radon flux density models were found to be most sensitive to the effective diffusion coefficient model selected, the emanation coefficient, and the radionuclide inventory. Using a site-specific measured effective diffusion coefficient significantly reduced the output uncertainty. When a site-specific effective-diffusion coefficient was used, the models were most sensitive to the emanation coefficient and the radionuclide inventory

Multiple predictor smoothing methods for sensitivity analysis.

Energy Technology Data Exchange (ETDEWEB)

Helton, Jon Craig; Storlie, Curtis B.

2006-08-01

The use of multiple predictor smoothing methods in sampling-based sensitivity analyses of complex models is investigated. Specifically, sensitivity analysis procedures based on smoothing methods employing the stepwise application of the following nonparametric regression techniques are described: (1) locally weighted regression (LOESS), (2) additive models, (3) projection pursuit regression, and (4) recursive partitioning regression. The indicated procedures are illustrated with both simple test problems and results from a performance assessment for a radioactive waste disposal facility (i.e., the Waste Isolation Pilot Plant). As shown by the example illustrations, the use of smoothing procedures based on nonparametric regression techniques can yield more informative sensitivity analysis results than can be obtained with more traditional sensitivity analysis procedures based on linear regression, rank regression or quadratic regression when nonlinear relationships between model inputs and model predictions are present.

Multiple predictor smoothing methods for sensitivity analysis

International Nuclear Information System (INIS)

Helton, Jon Craig; Storlie, Curtis B.

2006-01-01

The use of multiple predictor smoothing methods in sampling-based sensitivity analyses of complex models is investigated. Specifically, sensitivity analysis procedures based on smoothing methods employing the stepwise application of the following nonparametric regression techniques are described: (1) locally weighted regression (LOESS), (2) additive models, (3) projection pursuit regression, and (4) recursive partitioning regression. The indicated procedures are illustrated with both simple test problems and results from a performance assessment for a radioactive waste disposal facility (i.e., the Waste Isolation Pilot Plant). As shown by the example illustrations, the use of smoothing procedures based on nonparametric regression techniques can yield more informative sensitivity analysis results than can be obtained with more traditional sensitivity analysis procedures based on linear regression, rank regression or quadratic regression when nonlinear relationships between model inputs and model predictions are present

Alternative prediction methods of protein and energy evaluation of pig feeds.

Science.gov (United States)

Święch, Ewa

2017-01-01

Precise knowledge of the actual nutritional value of individual feedstuffs and complete diets for pigs is important for efficient livestock production. Methods of assessment of protein and energy values in pig feeds have been briefly described. In vivo determination of protein and energy values of feeds in pigs are time-consuming, expensive and very often require the use of surgically-modified animals. There is a need for more simple, rapid, inexpensive and reproducible methods for routine feed evaluation. Protein and energy values of pig feeds can be estimated using the following alternative methods: 1) prediction equations based on chemical composition; 2) animal models as rats, cockerels and growing pigs for adult animals; 3) rapid methods, such as the mobile nylon bag technique and in vitro methods. Alternative methods developed for predicting the total tract and ileal digestibility of nutrients including amino acids in feedstuffs and diets for pigs have been reviewed. This article focuses on two in vitro methods that can be used for the routine evaluation of amino acid ileal digestibility and energy value of pig feeds and on factors affecting digestibility determined in vivo in pigs and by alternative methods. Validation of alternative methods has been carried out by comparing the results obtained using these methods with those acquired in vivo in pigs. In conclusion, energy and protein values of pig feeds may be estimated with satisfactory precision in rats and by the two- or three-step in vitro methods providing equations for the calculation of standardized ileal digestibility of amino acids and metabolizable energy content. The use of alternative methods of feed evaluation is an important way for reduction of stressful animal experiments.

Alternative methods of ophthalmic treatment in Russia.

Science.gov (United States)

Vader, L

1994-04-01

Russian ophthalmic nurses and physicians are using alternative methods of treatment to supplement traditional eye care. As acupuncture and iridology become more popular in the United States, ophthalmic nurses need to be more knowledgeable about these treatments and the implications for patients.

Uncertainty and Sensitivity of Alternative Rn-222 Flux Density Models Used in Performance Assessment

Energy Technology Data Exchange (ETDEWEB)

Greg J. Shott, Vefa Yucel, Lloyd Desotell

2007-06-01

Performance assessments for the Area 5 Radioactive Waste Management Site on the Nevada Test Site have used three different mathematical models to estimate Rn-222 flux density. This study describes the performance, uncertainty, and sensitivity of the three models which include the U.S. Nuclear Regulatory Commission Regulatory Guide 3.64 analytical method and two numerical methods. The uncertainty of each model was determined by Monte Carlo simulation using Latin hypercube sampling. The global sensitivity was investigated using Morris one-at-time screening method, sample-based correlation and regression methods, the variance-based extended Fourier amplitude sensitivity test, and Sobol's sensitivity indices. The models were found to produce similar estimates of the mean and median flux density, but to have different uncertainties and sensitivities. When the Rn-222 effective diffusion coefficient was estimated using five different published predictive models, the radon flux density models were found to be most sensitive to the effective diffusion coefficient model selected, the emanation coefficient, and the radionuclide inventory. Using a site-specific measured effective diffusion coefficient significantly reduced the output uncertainty. When a site-specific effective-diffusion coefficient was used, the models were most sensitive to the emanation coefficient and the radionuclide inventory.

Enzyme-linked immunospot: an alternative method for the detection of interferon gamma in Johne's disease

DEFF Research Database (Denmark)

Begg, Douglas J.; de Silva, Kumudika; Bosward, Katrina

2009-01-01

To date, the sensitivity of the interferon gamma (IFN-) enzyme-linked immunosorbent assay (ELISA) to detect Johne's disease (JD) has been poor, especially in the early stages of disease. To improve the sensitivity of IFN- detection in the early stages of infection, an alternate assay needs to be ...

Sensitivity of ATLAS to alternative mechanisms of electroweak symmetry breaking in vector boson scattering qq→qqlνlν

International Nuclear Information System (INIS)

Schumacher, Jan W.

2010-10-01

An analysis of the expected sensitivity of the ATLAS experiment at the Large Hadron Collider at CERN to alternative mechanisms of electroweak symmetry breaking in the dileptonic vector boson scattering channel is presented. With the generalized K-Matrix model of vector boson scattering recently implemented in the event generator Whizard, several additional resonances are investigated. Whizard is validated for ATLAS use and an interface for the Les Houches event format is adapted for the ATLAS software Athena. Systematic model and statistical Monte Carlo uncertainties are reduced with a signal definition using events reweighted in the couplings g of the new resonances. Angular correlations conserved by Whizard are used in the event selection. A multivariate analyzer is trained to take into account correlations between the selection variables and thereby to improve the sensitivity compared to cut analyses. The statistical analysis is implemented with a profile likelihood method taking into account systematic uncertainties and statistical uncertainties from Monte Carlo. Ensemble tests are performed to assure the applicability of the method. Expected discovery significances and coupling limits for new additional resonances in vector boson scattering are determined. (orig.)

Some Convergence Strategies for the Alternating Generalized Projection Method

Directory of Open Access Journals (Sweden)

Maricarmen Andrade

2013-11-01

Full Text Available In this paper we extend the application of the alternating projection algorithm to solve the problem of finding a point in the intersection of $n$ sets ($n\\geq2$, which are not all of them convex sets. Here we term such method as alternating generalized projection (AGP method. In particular, we are interested in addressing the problem of avoiding the so-called trap points, which may prevent an algorithm to obtain a feasible solution in two or more sets not all convex. Some strategies that allow us to reach the feasible solution are established and conjectured. Finally, we present simple numerical results that illustrate the efficiency of the iterative methods considered.

A Web-based Alternative Non-animal Method Database for Safety Cosmetic Evaluations.

Science.gov (United States)

Kim, Seung Won; Kim, Bae-Hwan

2016-07-01

Animal testing was used traditionally in the cosmetics industry to confirm product safety, but has begun to be banned; alternative methods to replace animal experiments are either in development, or are being validated, worldwide. Research data related to test substances are critical for developing novel alternative tests. Moreover, safety information on cosmetic materials has neither been collected in a database nor shared among researchers. Therefore, it is imperative to build and share a database of safety information on toxicological mechanisms and pathways collected through in vivo, in vitro, and in silico methods. We developed the CAMSEC database (named after the research team; the Consortium of Alternative Methods for Safety Evaluation of Cosmetics) to fulfill this purpose. On the same website, our aim is to provide updates on current alternative research methods in Korea. The database will not be used directly to conduct safety evaluations, but researchers or regulatory individuals can use it to facilitate their work in formulating safety evaluations for cosmetic materials. We hope this database will help establish new alternative research methods to conduct efficient safety evaluations of cosmetic materials.

An ESDIRK Method with Sensitivity Analysis Capabilities

DEFF Research Database (Denmark)

Kristensen, Morten Rode; Jørgensen, John Bagterp; Thomsen, Per Grove

2004-01-01

of the sensitivity equations. A key feature is the reuse of information already computed for the state integration, hereby minimizing the extra effort required for sensitivity integration. Through case studies the new algorithm is compared to an extrapolation method and to the more established BDF based approaches...

A New Computationally Frugal Method For Sensitivity Analysis Of Environmental Models

Science.gov (United States)

Rakovec, O.; Hill, M. C.; Clark, M. P.; Weerts, A.; Teuling, R.; Borgonovo, E.; Uijlenhoet, R.

2013-12-01

Effective and efficient parameter sensitivity analysis methods are crucial to understand the behaviour of complex environmental models and use of models in risk assessment. This paper proposes a new computationally frugal method for analyzing parameter sensitivity: the Distributed Evaluation of Local Sensitivity Analysis (DELSA). The DELSA method can be considered a hybrid of local and global methods, and focuses explicitly on multiscale evaluation of parameter sensitivity across the parameter space. Results of the DELSA method are compared with the popular global, variance-based Sobol' method and the delta method. We assess the parameter sensitivity of both (1) a simple non-linear reservoir model with only two parameters, and (2) five different "bucket-style" hydrologic models applied to a medium-sized catchment (200 km2) in the Belgian Ardennes. Results show that in both the synthetic and real-world examples, the global Sobol' method and the DELSA method provide similar sensitivities, with the DELSA method providing more detailed insight at much lower computational cost. The ability to understand how sensitivity measures vary through parameter space with modest computational requirements provides exciting new opportunities.

Land management planning: a method of evaluating alternatives

Science.gov (United States)

Andres Weintraub; Richard Adams; Linda Yellin

1982-01-01

A method is described for developing and evaluating alternatives in land management planning. A structured set of 15 steps provides a framework for such an evaluation. when multiple objectives and uncertainty must be considered in the planning process. The method is consistent with other processes used in organizational evaluation, and allows for the interaction of...

Integrated Parasite Management for Livestock - Alternative control methods

Directory of Open Access Journals (Sweden)

Souvik Paul1

Full Text Available Internal parasites are considered by some to be one of the most economically important constraints in raising livestock. The growing concern about the resistance of internal parasites to all classes of dewormers has caused people to look for alternatives. As dewormers lose their effectiveness, the livestock community fears increasing economic losses from worms. There is no one thing that can be given or done to replace chemical dewormers. It will take a combination of extremely good management techniques and possibly some alternative therapies. It is not wise to think that one can just stop deworming animals with chemical dewormers. It is something one will need to change gradually, observing and testing animals and soil, in order to monitor the progress. Alternative parasite control is an area that is receiving a lot of interest and attention. Programs and research will continue in the pursuit of parasite control, using alternative and more management-intensive methods. [Veterinary World 2010; 3(9.000: 431-435

A general first-order global sensitivity analysis method

International Nuclear Information System (INIS)

Xu Chonggang; Gertner, George Zdzislaw

2008-01-01

Fourier amplitude sensitivity test (FAST) is one of the most popular global sensitivity analysis techniques. The main mechanism of FAST is to assign each parameter with a characteristic frequency through a search function. Then, for a specific parameter, the variance contribution can be singled out of the model output by the characteristic frequency. Although FAST has been widely applied, there are two limitations: (1) the aliasing effect among parameters by using integer characteristic frequencies and (2) the suitability for only models with independent parameters. In this paper, we synthesize the improvement to overcome the aliasing effect limitation [Tarantola S, Gatelli D, Mara TA. Random balance designs for the estimation of first order global sensitivity indices. Reliab Eng Syst Safety 2006; 91(6):717-27] and the improvement to overcome the independence limitation [Xu C, Gertner G. Extending a global sensitivity analysis technique to models with correlated parameters. Comput Stat Data Anal 2007, accepted for publication]. In this way, FAST can be a general first-order global sensitivity analysis method for linear/nonlinear models with as many correlated/uncorrelated parameters as the user specifies. We apply the general FAST to four test cases with correlated parameters. The results show that the sensitivity indices derived by the general FAST are in good agreement with the sensitivity indices derived by the correlation ratio method, which is a non-parametric method for models with correlated parameters

Application of Stochastic Sensitivity Analysis to Integrated Force Method

Directory of Open Access Journals (Sweden)

X. F. Wei

2012-01-01

Full Text Available As a new formulation in structural analysis, Integrated Force Method has been successfully applied to many structures for civil, mechanical, and aerospace engineering due to the accurate estimate of forces in computation. Right now, it is being further extended to the probabilistic domain. For the assessment of uncertainty effect in system optimization and identification, the probabilistic sensitivity analysis of IFM was further investigated in this study. A set of stochastic sensitivity analysis formulation of Integrated Force Method was developed using the perturbation method. Numerical examples are presented to illustrate its application. Its efficiency and accuracy were also substantiated with direct Monte Carlo simulations and the reliability-based sensitivity method. The numerical algorithm was shown to be readily adaptable to the existing program since the models of stochastic finite element and stochastic design sensitivity are almost identical.

Method-independent, Computationally Frugal Convergence Testing for Sensitivity Analysis Techniques

Science.gov (United States)

Mai, J.; Tolson, B.

2017-12-01

The increasing complexity and runtime of environmental models lead to the current situation that the calibration of all model parameters or the estimation of all of their uncertainty is often computationally infeasible. Hence, techniques to determine the sensitivity of model parameters are used to identify most important parameters. All subsequent model calibrations or uncertainty estimation procedures focus then only on these subsets of parameters and are hence less computational demanding. While the examination of the convergence of calibration and uncertainty methods is state-of-the-art, the convergence of the sensitivity methods is usually not checked. If any, bootstrapping of the sensitivity results is used to determine the reliability of the estimated indexes. Bootstrapping, however, might as well become computationally expensive in case of large model outputs and a high number of bootstraps. We, therefore, present a Model Variable Augmentation (MVA) approach to check the convergence of sensitivity indexes without performing any additional model run. This technique is method- and model-independent. It can be applied either during the sensitivity analysis (SA) or afterwards. The latter case enables the checking of already processed sensitivity indexes. To demonstrate the method's independency of the convergence testing method, we applied it to two widely used, global SA methods: the screening method known as Morris method or Elementary Effects (Morris 1991) and the variance-based Sobol' method (Solbol' 1993). The new convergence testing method is first scrutinized using 12 analytical benchmark functions (Cuntz & Mai et al. 2015) where the true indexes of aforementioned three methods are known. This proof of principle shows that the method reliably determines the uncertainty of the SA results when different budgets are used for the SA. The results show that the new frugal method is able to test the convergence and therefore the reliability of SA results in an

Alternative methods for dispoal of low-level radioactive wastes. Task 1. Description of methods and assessment of criteria

International Nuclear Information System (INIS)

Bennett, R.D.; Miller, W.O.; Warriner, J.B.; Malone, P.G.; McAneny, C.C.

1984-04-01

The study reported herein contains the results of Task 1 of a four-task study entitled Criteria for Evaluating Engineered Facilities. The overall objective of this study is to ensure that the criteria needed to evaluate five alternative low-level radioactive waste (LLW) disposal methods are available to the Nuclear Regulatory Commission (NRC) and the Agreement States. The alternative methods considered are belowground vaults, aboveground vaults, earth mounded concrete bunkers, mined cavities, and augered holes. Each of these alternatives is either being used by other countries for low-level radioactive waste (LLW) disposal or is being considered by other countries or US agencies. In this report the performance requirements are listed, each alternative is described, the experience gained with its use is discussed, and the performance capabilities of each method are addressed. Next, the existing 10 CFR Part 61 Subpart D criteria with respect to paragraphs 61.50 through 61.53, pertaining to site suitability, design, operations and closure, and monitoring are assessed for applicability to evaluation of each alternative. Preliminary conclusions and recommendations are offered on each method's suitability as an LLW disposal alternative, the applicability of the criteria, and the need for supplemental or modified criteria

A probabilistic method for species sensitivity distributions taking into account the inherent uncertainty and variability of effects to estimate environmental risk.

Science.gov (United States)

Gottschalk, Fadri; Nowack, Bernd

2013-01-01

This article presents a method of probabilistically computing species sensitivity distributions (SSD) that is well-suited to cope with distinct data scarcity and variability. First, a probability distribution that reflects the uncertainty and variability of sensitivity is modeled for each species considered. These single species sensitivity distributions are then combined to create an SSD for a particular ecosystem. A probabilistic estimation of the risk is carried out by combining the probability of critical environmental concentrations with the probability of organisms being impacted negatively by these concentrations. To evaluate the performance of the method, we developed SSD and risk calculations for the aquatic environment exposed to triclosan. The case studies showed that the probabilistic results reflect the empirical information well, and the method provides a valuable alternative or supplement to more traditional methods for calculating SSDs based on averaging raw data and/or on using theoretical distributional forms. A comparison and evaluation with single SSD values (5th-percentile [HC5]) revealed the robustness of the proposed method. Copyright © 2012 SETAC.

Timing of Peripheral Blood Stem Cell Yield: Comparison of Alternative Methods with the Classic Method for CD34+ Cell Determination

Directory of Open Access Journals (Sweden)

I. Fatorova

2014-01-01

Full Text Available Hematopoietic stem cells (HSCs, still represent a certain mystery in biology, have a unique property of dividing into equal cells and repopulating the hematopoietic tissue. This potential enables their use in transplantation treatments. The quality of the HSC grafts for transplantation is evaluated by flow cytometric determination of the CD34+ cells, which enables optimal timing of the first apheresis and the acquisition of maximal yield of the peripheral blood stem cells (PBSCs. To identify a more efficient method for evaluating CD34+ cells, we compared the following alternative methods with the reference method: hematopoietic progenitor cells (HPC enumeration (using the Sysmex XE-2100 analyser, detection of CD133+ cells, and quantification of aldehyde dehydrogenase activity in the PBSCs. 266 aphereses (84 patients were evaluated. In the preapheretic blood, the new methods produced data that were in agreement with the reference method. The ROC curves have shown that for the first-day apheresis target, the optimal predictive cut-off value was 0.032 cells/mL for the HPC method (sensitivity 73.4%, specificity 69.3%. HPC method exhibited a definite practical superiority as compared to other methods tested. HPC enumeration could serve as a supplementary method for the optimal timing of the first apheresis; it is simple, rapid, and cheap.

Sensitivity of ATLAS to alternative mechanisms of electroweak symmetry breaking in vector boson scattering qq{yields}qql{nu}l{nu}

Energy Technology Data Exchange (ETDEWEB)

Schumacher, Jan W

2010-10-15

An analysis of the expected sensitivity of the ATLAS experiment at the Large Hadron Collider at CERN to alternative mechanisms of electroweak symmetry breaking in the dileptonic vector boson scattering channel is presented. With the generalized K-Matrix model of vector boson scattering recently implemented in the event generator Whizard, several additional resonances are investigated. Whizard is validated for ATLAS use and an interface for the Les Houches event format is adapted for the ATLAS software Athena. Systematic model and statistical Monte Carlo uncertainties are reduced with a signal definition using events reweighted in the couplings g of the new resonances. Angular correlations conserved by Whizard are used in the event selection. A multivariate analyzer is trained to take into account correlations between the selection variables and thereby to improve the sensitivity compared to cut analyses. The statistical analysis is implemented with a profile likelihood method taking into account systematic uncertainties and statistical uncertainties from Monte Carlo. Ensemble tests are performed to assure the applicability of the method. Expected discovery significances and coupling limits for new additional resonances in vector boson scattering are determined. (orig.)

Safety relief valve alternate analysis method

International Nuclear Information System (INIS)

Adams, R.H.; Javid, A.; Khatua, T.P.

1981-01-01

An experimental test program was started in the United States in 1976 to define and quantify Safety Relief Valve (SRV) phenomena in General Electric Mark I Suppression Chambers. The testing considered several discharged devices and was used to correlate SRV load prediction models. The program was funded by utilities with Mark I containments and has resulted in a detailed SRV load definition as a portion of the Mark I containment program Load Definition Report (LDR). The (USNRC) has reviewed and approved the LDR SRV load definition. In addition, the USNRC has permitted calibration of structural models used for predicting torus response to SRV loads. Model calibration is subject to confirmatory in-plant testing. The SRV methodology given in the LDR requires that transient dynamic pressures be applied to a torus structural model that includes a fluid added mass matrix. Preliminary evaluations of torus response have indicated order of magnitude conservatisms, with respect to test results, which could result in unrealistic containment modifications. In addition, structural response trends observed in full-scale tests between cold pipe, first valve actuation and hot pipe, subsequent valve actuation conditions have not been duplicated using current analysis methods. It was suggested by others that an energy approach using current fluid models be utilized to define loads. An alternate SRV analysis method is defined to correct suppression chamber structural response to a level that permits economical but conservative design. Simple analogs are developed for the purpose of correcting the analytical response obtained from LDR analysis methods. Analogs evaluated considered forced vibration and free vibration structural response. The corrected response correlated well with in-plant test response. The correlation of the analytical model at test conditions permits application of the alternate analysis method at design conditions. (orig./HP)

Temperature sensitive surfaces and methods of making same

Science.gov (United States)

Liang, Liang [Richland, WA; Rieke, Peter C [Pasco, WA; Alford, Kentin L [Pasco, WA

2002-09-10

Poly-n-isopropylacrylamide surface coatings demonstrate the useful property of being able to switch charateristics depending upon temperature. More specifically, these coatings switch from being hydrophilic at low temperature to hydrophobic at high temperature. Research has been conducted for many years to better characterize and control the properties of temperature sensitive coatings. The present invention provides novel temperature sensitive coatings on articles and novel methods of making temperature sensitive coatings that are disposed on the surfaces of various articles. These novel coatings contain the reaction products of n-isopropylacrylamide and are characterized by their properties such as advancing contact angles. Numerous other characteristics such as coating thickness, surface roughness, and hydrophilic-to-hydrophobic transition temperatures are also described. The present invention includes articles having temperature-sensitve coatings with improved properties as well as improved methods for forming temperature sensitive coatings.

Ion-Exchange Membrane Chromatography as an Alternative Method of Separation of Potato y Virus

Directory of Open Access Journals (Sweden)

Treder Krzysztof

2015-12-01

Full Text Available Procedures of separation of virus particles from a plant material are multistage. Furthermore often they are difficult in terms of methodology and require use of expensive, highly specialist equipment and yield of separation is often low. The antigen obtained is often degraded and contains admixtures of other proteins. Therefore, generation of high quality and specificity antibodies based on such antigen is very difficult and quality of the antibodies has impact on reliability, sensitivity and unambiguity of results of immunodiagnostic tests (e.g. ELISA that are currently conventionally used to detect vegetable viruses. In this study three conventionally-performed methods of separation of potato virus Y (PVY were compared and a method of separation based on membrane chromatography, as an alternative separation technique, has been presented. It has been demonstrated that in proper process conditions good quality virus preparation can be obtained.

Clinical evaluation of pulmonary perfusion MRI using FAIR (flow-sensitive alternating inversion recovery)-HASTE (Half-Fourier Single-Shot TurboSE) method

International Nuclear Information System (INIS)

Togami, Izumi; Sasai, Nobuya; Tsunoda, Masatoshi; Sei, Tetsurou; Sato, Shuhei; Yabuki, Takayuki; Hiraki, Yoshio

2002-01-01

The FAIR-HASTE method is a kind of noninvasive perfusion MR imaging obtained without the use of contrast media. By subtracting a flow-insensitive image from a flow-sensitive image, contrast enhancement of inflowing blood achieved. In the present study, we applied pulmonary perfusion FAIR-HASTE sequence for 23 patients with various pulmonary diseases, and compared the findings with those by pulmonary perfusion scintigraphy and Gadolinium perfusion MRI. Pulmonary perfusion imaging with the FAIR-HASTE method was possible in all clinical cases, and the findings corresponded well to those obtained by perfusion MRI using contrast media or pulmonary scintigraphy. The FAIR-HASTE method is a promising method for the evaluation of pulmonary perfusion. (author)

Comparing sensitivity analysis methods to advance lumped watershed model identification and evaluation

Directory of Open Access Journals (Sweden)

Y. Tang

2007-01-01

Full Text Available This study seeks to identify sensitivity tools that will advance our understanding of lumped hydrologic models for the purposes of model improvement, calibration efficiency and improved measurement schemes. Four sensitivity analysis methods were tested: (1 local analysis using parameter estimation software (PEST, (2 regional sensitivity analysis (RSA, (3 analysis of variance (ANOVA, and (4 Sobol's method. The methods' relative efficiencies and effectiveness have been analyzed and compared. These four sensitivity methods were applied to the lumped Sacramento soil moisture accounting model (SAC-SMA coupled with SNOW-17. Results from this study characterize model sensitivities for two medium sized watersheds within the Juniata River Basin in Pennsylvania, USA. Comparative results for the 4 sensitivity methods are presented for a 3-year time series with 1 h, 6 h, and 24 h time intervals. The results of this study show that model parameter sensitivities are heavily impacted by the choice of analysis method as well as the model time interval. Differences between the two adjacent watersheds also suggest strong influences of local physical characteristics on the sensitivity methods' results. This study also contributes a comprehensive assessment of the repeatability, robustness, efficiency, and ease-of-implementation of the four sensitivity methods. Overall ANOVA and Sobol's method were shown to be superior to RSA and PEST. Relative to one another, ANOVA has reduced computational requirements and Sobol's method yielded more robust sensitivity rankings.

Screening of alternative methods for the disposal of low-level radioactive wastes

International Nuclear Information System (INIS)

Macbeth, P.J.; Thamer, B.J.; Christensen, D.E.; Wehmann, G.

1978-10-01

A systematic method for categorizing these disposal alternatives which provides assurance that no viable alternatives are overlooked is reported. Alternatives are categorized by (1) the general media in which disposal occurs, (2) by whether the disposal method can be considered as dispersal, containment or elimination of the wastes, and (3) by the applicability of the disposal method to the possible physical waste forms. A literature survey was performed and pertinent references listed for the various alternatives discussed. A bibliography is given which provides coverage of published information on low-level radioactive waste management options. The extensive list of disposal alternatives identified was screened and the most viable choices were selected for further evaluation. A Technical Advisory Panel met and reviewed the results. Suggestions from that meeting and other comments are discussed. The most viable options selected for further evaluation are: (1) improving present shallow land burial practices; (2) deeper depth burial; (3) disposal in cavities; (4) disposal in exposed or buried structures; and (5) ocean disposal. 42 references

International Harmonization and Cooperation in the Validation of Alternative Methods.

Science.gov (United States)

Barroso, João; Ahn, Il Young; Caldeira, Cristiane; Carmichael, Paul L; Casey, Warren; Coecke, Sandra; Curren, Rodger; Desprez, Bertrand; Eskes, Chantra; Griesinger, Claudius; Guo, Jiabin; Hill, Erin; Roi, Annett Janusch; Kojima, Hajime; Li, Jin; Lim, Chae Hyung; Moura, Wlamir; Nishikawa, Akiyoshi; Park, HyeKyung; Peng, Shuangqing; Presgrave, Octavio; Singer, Tim; Sohn, Soo Jung; Westmoreland, Carl; Whelan, Maurice; Yang, Xingfen; Yang, Ying; Zuang, Valérie

The development and validation of scientific alternatives to animal testing is important not only from an ethical perspective (implementation of 3Rs), but also to improve safety assessment decision making with the use of mechanistic information of higher relevance to humans. To be effective in these efforts, it is however imperative that validation centres, industry, regulatory bodies, academia and other interested parties ensure a strong international cooperation, cross-sector collaboration and intense communication in the design, execution, and peer review of validation studies. Such an approach is critical to achieve harmonized and more transparent approaches to method validation, peer-review and recommendation, which will ultimately expedite the international acceptance of valid alternative methods or strategies by regulatory authorities and their implementation and use by stakeholders. It also allows achieving greater efficiency and effectiveness by avoiding duplication of effort and leveraging limited resources. In view of achieving these goals, the International Cooperation on Alternative Test Methods (ICATM) was established in 2009 by validation centres from Europe, USA, Canada and Japan. ICATM was later joined by Korea in 2011 and currently also counts with Brazil and China as observers. This chapter describes the existing differences across world regions and major efforts carried out for achieving consistent international cooperation and harmonization in the validation and adoption of alternative approaches to animal testing.

Resonance-induced sensitivity enhancement method for conductivity sensors

Science.gov (United States)

Tai, Yu-Chong (Inventor); Shih, Chi-yuan (Inventor); Li, Wei (Inventor); Zheng, Siyang (Inventor)

2009-01-01

Methods and systems for improving the sensitivity of a variety of conductivity sensing devices, in particular capacitively-coupled contactless conductivity detectors. A parallel inductor is added to the conductivity sensor. The sensor with the parallel inductor is operated at a resonant frequency of the equivalent circuit model. At the resonant frequency, parasitic capacitances that are either in series or in parallel with the conductance (and possibly a series resistance) is substantially removed from the equivalent circuit, leaving a purely resistive impedance. An appreciably higher sensor sensitivity results. Experimental verification shows that sensitivity improvements of the order of 10,000-fold are possible. Examples of detecting particulates with high precision by application of the apparatus and methods of operation are described.

Highly sensitive fiber grating chemical sensors: An effective alternative to atomic absorption spectroscopy

Science.gov (United States)

Laxmeshwar, Lata. S.; Jadhav, Mangesh S.; Akki, Jyoti. F.; Raikar, Prasad; Kumar, Jitendra; prakash, Om; Raikar, U. S.

2017-06-01

Accuracy in quantitative determination of trace elements like Zinc, present in drinking water in ppm level, is a big challenge and optical fiber gratings as chemical sensors may provide a promising solution to overcome the same. This paper presents design of two simple chemical sensors based on the principle of shift in characteristic wavelength of gratings with change in their effective refractive index, to measure the concentration of Zinc in drinking water using etched short period grating (FBG) and Long period grating (LPG) respectively. Three samples of drinking water from different places have been examined for presence of Zinc. Further, the results obtained by our sensors have also been verified with the results obtained by a standard method, Atomic absorption spectroscopy (AAS). The whole experiment has been performed by fixing the fibers in a horizontal position with the sensor regions at the center of the fibers, making it less prone to disturbance and breaking. The sensitivity of LPG sensor is about 205 times that of the FBG sensor. A few advantages of Fiber grating sensors, besides their regular features, over AAS have also been discussed, that make our sensors potential alternatives for existing techniques in determination of trace elements in drinking water.

NK sensitivity of neuroblastoma cells determined by a highly sensitive coupled luminescent method

International Nuclear Information System (INIS)

Ogbomo, Henry; Hahn, Anke; Geiler, Janina; Michaelis, Martin; Doerr, Hans Wilhelm; Cinatl, Jindrich

2006-01-01

The measurement of natural killer (NK) cells toxicity against tumor or virus-infected cells especially in cases with small blood samples requires highly sensitive methods. Here, a coupled luminescent method (CLM) based on glyceraldehyde-3-phosphate dehydrogenase release from injured target cells was used to evaluate the cytotoxicity of interleukin-2 activated NK cells against neuroblastoma cell lines. In contrast to most other methods, CLM does not require the pretreatment of target cells with labeling substances which could be toxic or radioactive. The effective killing of tumor cells was achieved by low effector/target ratios ranging from 0.5:1 to 4:1. CLM provides highly sensitive, safe, and fast procedure for measurement of NK cell activity with small blood samples such as those obtained from pediatric patients

The European Partnership for Alternative Approaches to Animal Testing (EPAA): promoting alternative methods in Europe and beyond.

Science.gov (United States)

Cozigou, Gwenole; Crozier, Jonathan; Hendriksen, Coenraad; Manou, Irene; Ramirez-Hernandez, Tzutzuy; Weissenhorn, Renate

2015-03-01

Here in we introduce the European Partnership for Alternative Approaches to Animal Testing (EPAA) and its activities, which are focused on international cooperation toward alternative methods. The EPAA is one of the leading organizations in Europe for the promotion of alternative approaches to animal testing. Its innovative public-private partnership structure enables a consensus-driven dialogue across 7 industry sectors to facilitate interaction between regulators and regulated stakeholders. Through a brief description of EPAA's activities and organizational structure, we first articulate the value of this collaboration; we then focus on 2 key projects driven by EPAA. The first project aims to address research gaps on stem cells for safety testing, whereas the second project strives for an approach toward demonstration of consistency in vaccine batch release testing. We highlight the growing need for harmonization of international acceptance and implementation of alternative approaches and for increased international collaboration to foster progress on nonanimal alternatives.

Efficient and effective implementation of alternative project delivery methods.

Science.gov (United States)

2017-05-01

Over the past decade, the Maryland Department of Transportation State Highway : Administration (MDOT SHA) has implemented Alternative Project Delivery (APD) methods : in a number of transportation projects. While these innovative practices have produ...

77 FR 17457 - Work Group on Alternative Test Methods for Commercial Measuring Devices

Science.gov (United States)

2012-03-26

... DEPARTMENT OF COMMERCE National Institute of Standards and Technology Work Group on Alternative... Work Group (WG) to examine alternative methods for testing the accuracy of commercial measuring devices... participates to promote uniformity among the states in laws, regulations, methods, and testing equipment that...

Sensitivity analysis of infectious disease models: methods, advances and their application

Science.gov (United States)

Wu, Jianyong; Dhingra, Radhika; Gambhir, Manoj; Remais, Justin V.

2013-01-01

Sensitivity analysis (SA) can aid in identifying influential model parameters and optimizing model structure, yet infectious disease modelling has yet to adopt advanced SA techniques that are capable of providing considerable insights over traditional methods. We investigate five global SA methods—scatter plots, the Morris and Sobol’ methods, Latin hypercube sampling-partial rank correlation coefficient and the sensitivity heat map method—and detail their relative merits and pitfalls when applied to a microparasite (cholera) and macroparasite (schistosomaisis) transmission model. The methods investigated yielded similar results with respect to identifying influential parameters, but offered specific insights that vary by method. The classical methods differed in their ability to provide information on the quantitative relationship between parameters and model output, particularly over time. The heat map approach provides information about the group sensitivity of all model state variables, and the parameter sensitivity spectrum obtained using this method reveals the sensitivity of all state variables to each parameter over the course of the simulation period, especially valuable for expressing the dynamic sensitivity of a microparasite epidemic model to its parameters. A summary comparison is presented to aid infectious disease modellers in selecting appropriate methods, with the goal of improving model performance and design. PMID:23864497

Evaluating the sensitization potential of surfactants: integrating data from the local lymph node assay, guinea pig maximization test, and in vitro methods in a weight-of-evidence approach.

Science.gov (United States)

Ball, Nicholas; Cagen, Stuart; Carrillo, Juan-Carlos; Certa, Hans; Eigler, Dorothea; Emter, Roger; Faulhammer, Frank; Garcia, Christine; Graham, Cynthia; Haux, Carl; Kolle, Susanne N; Kreiling, Reinhard; Natsch, Andreas; Mehling, Annette

2011-08-01

An integral part of hazard and safety assessments is the estimation of a chemical's potential to cause skin sensitization. Currently, only animal tests (OECD 406 and 429) are accepted in a regulatory context. Nonanimal test methods are being developed and formally validated. In order to gain more insight into the responses induced by eight exemplary surfactants, a battery of in vivo and in vitro tests were conducted using the same batch of chemicals. In general, the surfactants were negative in the GPMT, KeratinoSens and hCLAT assays and none formed covalent adducts with test peptides. In contrast, all but one was positive in the LLNA. Most were rated as being irritants by the EpiSkin assay with the additional endpoint, IL1-alpha. The weight of evidence based on this comprehensive testing indicates that, with one exception, they are non-sensitizing skin irritants, confirming that the LLNA tends to overestimate the sensitization potential of surfactants. As results obtained from LLNAs are considered as the gold standard for the development of new nonanimal alternative test methods, results such as these highlight the necessity to carefully evaluate the applicability domains of test methods in order to develop reliable nonanimal alternative testing strategies for sensitization testing. Copyright © 2011 Elsevier Inc. All rights reserved.

Relative valuation of alternative methods of tax avoidance

OpenAIRE

Inger, Kerry Katharine

2012-01-01

This paper examines the relative valuation of alternative methods of tax avoidance. Prior studies find that firm value is positively associated with overall measures of tax avoidance; I extend this research by providing evidence that investors distinguish between methods of tax reduction in their valuation of tax avoidance. The impact of tax avoidance on firm value is a function of tax risk, permanence of tax savings, tax planning costs, implicit taxes and contrasts in disclosures of tax re...

Method of characteristics - Based sensitivity calculations for international PWR benchmark

International Nuclear Information System (INIS)

Suslov, I. R.; Tormyshev, I. V.; Komlev, O. G.

2013-01-01

Method to calculate sensitivity of fractional-linear neutron flux functionals to transport equation coefficients is proposed. Implementation of the method on the basis of MOC code MCCG3D is developed. Sensitivity calculations for fission intensity for international PWR benchmark are performed. (authors)

The Sine Method: An Alternative Height Measurement Technique

Science.gov (United States)

Don C. Bragg; Lee E. Frelich; Robert T. Leverett; Will Blozan; Dale J. Luthringer

2011-01-01

Height is one of the most important dimensions of trees, but few observers are fully aware of the consequences of the misapplication of conventional height measurement techniques. A new approach, the sine method, can improve height measurement by being less sensitive to the requirements of conventional techniques (similar triangles and the tangent method). We studied...

Is Grey Level a Suitable Alternative to Low-Contrast Penetration as a Serial Measure of Sensitivity in Computerised Ultrasound Quality Assurance?

Science.gov (United States)

Dudley, Nicholas J; Gibson, Nicholas M

2017-02-01

The aim of this study was to test the hypothesis that grey levels are a suitable alternative measure of sensitivity in ultrasound imaging quality assurance, as there are several caveats in the use of penetration depth. In a primary cohort of nine probes, where measurements had been made for 6 to 34 mo, both penetration depth and mean grey level fell below tolerance for six probes; both penetration depth and mean grey level remained within tolerance for three probes. In a secondary cohort where a measurement programme had been in place for a shorter period, grey level and/or penetration depth fell below tolerance in 15 of 66 probes; the sensitivity and specificity of at least 10% loss of grey level in predicting >5% loss in penetration depth were 91% and 93%, respectively. A loss of grey level accompanies a loss of penetration and provides a suitable alternative measure of sensitivity. Crown Copyright © 2016. Published by Elsevier Inc. All rights reserved.

Multivariate Models for Prediction of Human Skin Sensitization Hazard

Science.gov (United States)

Strickland, Judy; Zang, Qingda; Paris, Michael; Lehmann, David M.; Allen, David; Choksi, Neepa; Matheson, Joanna; Jacobs, Abigail; Casey, Warren; Kleinstreuer, Nicole

2016-01-01

One of ICCVAM’s top priorities is the development and evaluation of non-animal approaches to identify potential skin sensitizers. The complexity of biological events necessary to produce skin sensitization suggests that no single alternative method will replace the currently accepted animal tests. ICCVAM is evaluating an integrated approach to testing and assessment based on the adverse outcome pathway for skin sensitization that uses machine learning approaches to predict human skin sensitization hazard. We combined data from three in chemico or in vitro assays—the direct peptide reactivity assay (DPRA), human cell line activation test (h-CLAT), and KeratinoSens™ assay—six physicochemical properties, and an in silico read-across prediction of skin sensitization hazard into 12 variable groups. The variable groups were evaluated using two machine learning approaches, logistic regression (LR) and support vector machine (SVM), to predict human skin sensitization hazard. Models were trained on 72 substances and tested on an external set of 24 substances. The six models (three LR and three SVM) with the highest accuracy (92%) used: (1) DPRA, h-CLAT, and read-across; (2) DPRA, h-CLAT, read-across, and KeratinoSens; or (3) DPRA, h-CLAT, read-across, KeratinoSens, and log P. The models performed better at predicting human skin sensitization hazard than the murine local lymph node assay (accuracy = 88%), any of the alternative methods alone (accuracy = 63–79%), or test batteries combining data from the individual methods (accuracy = 75%). These results suggest that computational methods are promising tools to effectively identify potential human skin sensitizers without animal testing. PMID:27480324

Improved sensitivity testing of explosives using transformed Up-Down methods

International Nuclear Information System (INIS)

Brown, Geoffrey W

2014-01-01

Sensitivity tests provide data that help establish guidelines for the safe handling of explosives. Any sensitivity test is based on assumptions to simplify the method or reduce the number of individual sample evaluations. Two common assumptions that are not typically checked after testing are 1) explosive response follows a normal distribution as a function of the applied stimulus levels and 2) the chosen test level spacing is close to the standard deviation of the explosive response function (for Bruceton Up-Down testing for example). These assumptions and other limitations of traditional explosive sensitivity testing can be addressed using Transformed Up-Down (TUD) test methods. TUD methods have been developed extensively for psychometric testing over the past 50 years and generally use multiple tests at a given level to determine how to adjust the applied stimulus. In the context of explosive sensitivity we can use TUD methods that concentrate testing around useful probability levels. Here, these methods are explained and compared to Bruceton Up-Down testing using computer simulation. The results show that the TUD methods are more useful for many cases but that they do require more tests as a consequence. For non-normal distributions, however, the TUD methods may be the only accurate assessment method.

Exploring Intercultural Sensitivity in Early Adolescence: A Mixed Methods Study

Science.gov (United States)

Mellizo, Jennifer M.

2017-01-01

The purpose of this mixed methods study was to explore levels of intercultural sensitivity in a sample of fourth to eighth grade students in the United States (n = 162). "Intercultural sensitivity" was conceptualised through Bennett's Developmental Model of Sensitivity, and assessed through the Adapted Intercultural Sensitivity Index.…

A more sensitive, efficient and ISO 17025 validated Magnetic Capture real time PCR method for the detection of archetypal Toxoplasma gondii strains in meat.

Science.gov (United States)

Gisbert Algaba, Ignacio; Geerts, Manon; Jennes, Malgorzata; Coucke, Wim; Opsteegh, Marieke; Cox, Eric; Dorny, Pierre; Dierick, Katelijne; De Craeye, Stéphane

2017-11-01

Toxoplasma gondii is a globally prevalent, zoonotic parasite of major importance to public health. Various indirect and direct methods can be used for the diagnosis of toxoplasmosis. Whereas serological tests are useful to prove contact with the parasite has occurred, the actual presence of the parasite in the tissues of a seropositive animal is not demonstrated. For this, a bioassay is still the reference method. As an alternative, various PCR methods have been developed, but due to the limited amount of sample that can be tested, combined with a low tissue cyst density, those have proved to be insufficiently sensitive. A major improvement of the sensitivity was achieved with magnetic capture-based DNA extraction. By combining the hybridization of specific, biotinylated probes with the capture of those probes with streptavidin-coated paramagnetic beads, T. gondii DNA can selectively be "fished out" from a large volume of meat lysate. Still, several studies showed an insufficient sensitivity compared with the mouse bioassay. Here we present a method that is more sensitive (99% limit of detection: 65.4 tachyzoites per 100g of meat), economical and reliable (ISO 17025 validated) by adding a non-competitive PCR inhibition control (co-capture of cellular r18S) and making the release of the target DNA from the streptavidin-coated paramagnetic beads UV-dependent. The presented results demonstrate the potential of the modified Magnetic Capture real time PCR as a full alternative to the mouse bioassay for the screening of various types of tissues and meat, with the additional advantage of being quantitative. Copyright © 2017 Australian Society for Parasitology. Published by Elsevier Ltd. All rights reserved.

Are LOD and LOQ Reliable Parameters for Sensitivity Evaluation of Spectroscopic Methods?

Science.gov (United States)

Ershadi, Saba; Shayanfar, Ali

2018-03-22

The limit of detection (LOD) and the limit of quantification (LOQ) are common parameters to assess the sensitivity of analytical methods. In this study, the LOD and LOQ of previously reported terbium sensitized analysis methods were calculated by different methods, and the results were compared with sensitivity parameters [lower limit of quantification (LLOQ)] of U.S. Food and Drug Administration guidelines. The details of the calibration curve and standard deviation of blank samples of three different terbium-sensitized luminescence methods for the quantification of mycophenolic acid, enrofloxacin, and silibinin were used for the calculation of LOD and LOQ. A comparison of LOD and LOQ values calculated by various methods and LLOQ shows a considerable difference. The significant difference of the calculated LOD and LOQ with various methods and LLOQ should be considered in the sensitivity evaluation of spectroscopic methods.

Evaluation of alternative methods for the disposal of low-level radioactive wastes

International Nuclear Information System (INIS)

Macbeth, P.; Wehmann, G.; Thamer, B.J.; Card, D.H.

1979-07-01

A comparative analysis of the most viable alternatives for disposal of solid low-level radioactive wastes is presented to aid in evaluating national waste management options. Four basic alternative methods are analyzed and compared to the present practice of shallow land burial. These include deeper burial, disposal in mined cavities, disposal in engineered structures, and disposal in the oceans. Some variations in the basic methods are also presented. Technical, socio-political, and economic factors are assigened relative importances (weights) and evaluated for the various alternatives. Based on disposal of a constant volume of waste with given nuclear characteristics, the most desirable alternatives to shallow land burial in descending order of desirability appear to be: improving present practices, deeper burial, use of acceptable abandoned mines, new mines, ocean dumping, and structural disposal concepts. It must be emphasized that the evaluations reported here are generic, and use of other weights or different values for specific sites could change the conclusions and ordering of alternatives determined in this study. Impacts and costs associated with transportation over long distances predominate over differences among alternatives, indicating the desireability of establishing regional waste disposal locations. The impacts presented are for generic comparisons among alternatives, and are not intended to be predictive of the performance of any actual waste disposal facility

Novel Method for Sizing Metallic Bottom Crack Depth Using Multi-frequency Alternating Current Potential Drop Technique

Directory of Open Access Journals (Sweden)

Li Yuting

2015-10-01

Full Text Available Potential drop techniques are of two types: the direct current potential drop (DCPD technique and alternating current potential drop (ACPD technique, and both of them are used in nondestructive testing. ACPD, as a kind of valid method in sizing metal cracks, has been applied to evaluate metal structures. However, our review of most available approaches revealed that some improvements can be done in measuring depth of metal bottom crack by means of ACPD, such as accuracy and sensitivity of shallow crack. This paper studied a novel method which utilized the slope of voltage ratio-frequency curve to solve bottom crack depth by using a simple mathematic equation based on finite element analysis. It is found that voltage ratio varies linearly with frequency in the range of 5-15 Hz; this range is slightly higher than the equivalent frequency and lower than semi-permeable frequency. Simulation and experiment show that the novel method can measure the bottom crack depth accurately.

Novel Method for Sizing Metallic Bottom Crack Depth Using Multi-frequency Alternating Current Potential Drop Technique

Science.gov (United States)

Li, Yuting; Gan, Fangji; Wan, Zhengjun; Liao, Junbi; Li, Wenqiang

2015-10-01

Potential drop techniques are of two types: the direct current potential drop (DCPD) technique and alternating current potential drop (ACPD) technique, and both of them are used in nondestructive testing. ACPD, as a kind of valid method in sizing metal cracks, has been applied to evaluate metal structures. However, our review of most available approaches revealed that some improvements can be done in measuring depth of metal bottom crack by means of ACPD, such as accuracy and sensitivity of shallow crack. This paper studied a novel method which utilized the slope of voltage ratio-frequency curve to solve bottom crack depth by using a simple mathematic equation based on finite element analysis. It is found that voltage ratio varies linearly with frequency in the range of 5-15 Hz; this range is slightly higher than the equivalent frequency and lower than semi-permeable frequency. Simulation and experiment show that the novel method can measure the bottom crack depth accurately.

Alternative method of retesting UF{sub 6} cylinders

Energy Technology Data Exchange (ETDEWEB)

Christ, R. [Nuclear Crago + Service GmbH, Hanau (Germany)

1991-12-31

The paper describes an alternative method to perform the periodic inspection of UF{sub 6} cylinders. The hydraulic test is replaced by ultrasonic checking of wall thickness and by magnetic particle testing of all the weld seams. Information about the legal background, the air leak test and the qualification of inspectors is also given.

Laboratory-scale evaluations of alternative plutonium precipitation methods

International Nuclear Information System (INIS)

Martella, L.L.; Saba, M.T.; Campbell, G.K.

1984-01-01

Plutonium(III), (IV), and (VI) carbonate; plutonium(III) fluoride; plutonium(III) and (IV) oxalate; and plutonium(IV) and (VI) hydroxide precipitation methods were evaluated for conversion of plutonium nitrate anion-exchange eluate to a solid, and compared with the current plutonium peroxide precipitation method used at Rocky Flats. Plutonium(III) and (IV) oxalate, plutonium(III) fluoride, and plutonium(IV) hydroxide precipitations were the most effective of the alternative conversion methods tested because of the larger particle-size formation, faster filtration rates, and the low plutonium loss to the filtrate. These were found to be as efficient as, and in some cases more efficient than, the peroxide method. 18 references, 14 figures, 3 tables

Sensitivity study with respect to direction of ADI method during re-flooding in AHWR

Energy Technology Data Exchange (ETDEWEB)

Kumar, M.; Mukhopadhyay, D. [Bhabha Atomic Research Centre, Mumbai (India). Reactor Safety Div.; Ghosh, A.K. [Bhabha Atomic Research Centre, Mumbai (India). Raja Ramanna Fellow; Kumar, R. [Indian Institute of Technology, Roorkee (India)

2015-05-15

The Advanced Heavy water Reactor (AHWR) is a natural circulation vertical pressure tube type boiling light water cooled and heavy water moderated reactor. As the AHWR fuel bundle quenching under accident condition is designed primarily with radial jets at several axial locations, bottom re-flooding still remain open as another option. Radial direction injection of emergency core cooling leads to rewetting of AHWR fuel cluster in circumferential direction. A 3D fuel pin model has been developed by using Finite Difference Method (FDM) of transient heat conduction equation. Alternating Direction Implicit technique of Finite Difference Method (FDM) has been used for discretisation of numerical equation in different time step at different direction. Sensitivity numerical study with respect to direction of ADI method has been carried out to optimize the time step during the transient as well as steady state and is found that it is insensitivity with direction of solution. Further, to assess influence of circumferential rewetting vis-a-vis axial rewetting. Both the analyses are carried out with same fluid temperature and heat transfer coefficients as boundary conditions. It has been found from the analyses that for radial jet, the circumferential conduction is significant and overall the fuel temperature falls in the quench plane with the initiation of quenching event. The paper discusses the sensitivity study with respect to direction of ADI solution and comparison of numerical results for circumferential and axial rewetting for single pin.

Multivariate Models for Prediction of Human Skin Sensitization ...

Science.gov (United States)

One of the lnteragency Coordinating Committee on the Validation of Alternative Method's (ICCVAM) top priorities is the development and evaluation of non-animal approaches to identify potential skin sensitizers. The complexity of biological events necessary to produce skin sensitization suggests that no single alternative method will replace the currently accepted animal tests. ICCVAM is evaluating an integrated approach to testing and assessment based on the adverse outcome pathway for skin sensitization that uses machine learning approaches to predict human skin sensitization hazard. We combined data from three in chemico or in vitro assays - the direct peptide reactivity assay (DPRA), human cell line activation test (h-CLAT) and KeratinoSens TM assay - six physicochemical properties and an in silico read-across prediction of skin sensitization hazard into 12 variable groups. The variable groups were evaluated using two machine learning approaches , logistic regression and support vector machine, to predict human skin sensitization hazard. Models were trained on 72 substances and tested on an external set of 24 substances. The six models (three logistic regression and three support vector machine) with the highest accuracy (92%) used: (1) DPRA, h-CLAT and read-across; (2) DPRA, h-CLAT, read-across and KeratinoSens; or (3) DPRA, h-CLAT, read-across, KeratinoSens and log P. The models performed better at predicting human skin sensitization hazard than the murine

Innovative Solutions for Words with Emphasis: Alternative Methods of Braille Transcription

Science.gov (United States)

Kamei-Hannan, Cheryl

2009-01-01

The author of this study proposed two alternative methods for transcribing words with emphasis into braille and compared the use of the symbols for emphasis with the current braille code. The results showed that students were faster at locating words presented in one of the alternate formats, but that there was no difference in students' accuracy…

77 FR 40358 - Meeting of the Scientific Advisory Committee on Alternative Toxicological Methods (SACATM)

Science.gov (United States)

2012-07-09

..., revised, and alternative safety testing methods with regulatory applicability and promotes the scientific... DEPARTMENT OF HEALTH AND HUMAN SERVICES Meeting of the Scientific Advisory Committee on Alternative Toxicological Methods (SACATM) AGENCY: Division of the National Toxicology Program (DNTP...

Sensitivity Analysis of Structures by Virtual Distortion Method

DEFF Research Database (Denmark)

Gierlinski, J.T.; Holnicki-Szulc, J.; Sørensen, John Dalsgaard

1991-01-01

are used in structural optimization, see Haftka [4]. The recently developed Virtual Distortion Method (VDM) is a numerical technique which offers an efficient approach to calculation of the sensitivity derivatives. This method has been orginally applied to structural remodelling and collapse analysis, see...

Optimal purification and sensitive quantification of DNA from fecal samples

DEFF Research Database (Denmark)

Jensen, Annette Nygaard; Hoorfar, Jeffrey

2002-01-01

Application of reliable, rapid and sensitive methods to laboratory diagnosis of zoonotic infections continues to challenge microbiological laboratories. The recovery of DNA from a swine fecal sample and a bacterial culture extracted by a conventional phenol-chloroform extraction method was compared...... = 0.99 and R-2 = 1.00). In conclusion, silica-membrane, columns can provide a more convenient and less hazardous alternative to the conventional phenol-based method. The results have implication for further improvement of sensitive amplification methods for laboratory diagnosis....

Pathway analysis for alternate low-level waste disposal methods

International Nuclear Information System (INIS)

Rao, R.R.; Kozak, M.W.; McCord, J.T.; Olague, N.E.

1992-01-01

The purpose of this paper is to evaluate a complete set of environmental pathways for disposal options and conditions that the Nuclear Regulatory Commission (NRC) may analyze for a low-level radioactive waste (LLW) license application. The regulations pertaining In the past, shallow-land burial has been used for the disposal of low-level radioactive waste. However, with the advent of the State Compact system of LLW disposal, many alternative technologies may be used. The alternative LLW disposal facilities include below- ground vault, tumulus, above-ground vault, shaft, and mine disposal This paper will form the foundation of an update of the previously developed Sandia National Laboratories (SNL)/NRC LLW performance assessment methodology. Based on the pathway assessment for alternative disposal methods, a determination will be made about whether the current methodology can satisfactorily analyze the pathways and phenomena likely to be important for the full range of potential disposal options. We have attempted to be conservative in keeping pathways in the lists that may usually be of marginal importance. In this way we can build confidence that we have spanned the range of cases likely to be encountered at a real site. Results of the pathway assessment indicate that disposal methods can be categorized in groupings based on their depth of disposal. For the deep disposal options of shaft and mine disposal, the key pathways are identical. The shallow disposal options, such as tumulus, shallow-land, and below-ground vault disposal also may be grouped together from a pathway analysis perspective. Above-ground vault disposal cannot be grouped with any of the other disposal options. The pathway analysis shows a definite trend concerning depth of disposal. The above-ground option has the largest number of significant pathways. As the waste becomes more isolated, the number of significant pathways is reduced. Similar to shallow-land burial, it was found that for all

An Alternative Method to Gauss-Jordan Elimination: Minimizing Fraction Arithmetic

Science.gov (United States)

Smith, Luke; Powell, Joan

2011-01-01

When solving systems of equations by using matrices, many teachers present a Gauss-Jordan elimination approach to row reducing matrices that can involve painfully tedious operations with fractions (which I will call the traditional method). In this essay, I present an alternative method to row reduce matrices that does not introduce additional…

Multiple predictor smoothing methods for sensitivity analysis: Example results

International Nuclear Information System (INIS)

Storlie, Curtis B.; Helton, Jon C.

2008-01-01

The use of multiple predictor smoothing methods in sampling-based sensitivity analyses of complex models is investigated. Specifically, sensitivity analysis procedures based on smoothing methods employing the stepwise application of the following nonparametric regression techniques are described in the first part of this presentation: (i) locally weighted regression (LOESS), (ii) additive models, (iii) projection pursuit regression, and (iv) recursive partitioning regression. In this, the second and concluding part of the presentation, the indicated procedures are illustrated with both simple test problems and results from a performance assessment for a radioactive waste disposal facility (i.e., the Waste Isolation Pilot Plant). As shown by the example illustrations, the use of smoothing procedures based on nonparametric regression techniques can yield more informative sensitivity analysis results than can be obtained with more traditional sensitivity analysis procedures based on linear regression, rank regression or quadratic regression when nonlinear relationships between model inputs and model predictions are present

Alternative containment integrity test methods, an overview of possible techniques

International Nuclear Information System (INIS)

Spletzer, B.L.

1986-01-01

A study is being conducted to develop and analyze alternative methods for testing of containment integrity. The study is focused on techniques for continuously monitoring containment integrity to provide rapid detection of existing leaks, thus providing greater certainty of the integrity of the containment at any time. The study is also intended to develop techniques applicable to the currently required Type A integrated leakage rate tests. A brief discussion of the range of alternative methods currently being considered is presented. The methods include applicability to all major containment types, operating and shutdown plant conditions, and quantitative and qualitative leakage measurements. The techniques are analyzed in accordance with the current state of knowledge of each method. The bulk of the techniques discussed are in the conceptual stage, have not been tested in actual plant conditions, and are presented here as a possible future direction for evaluating containment integrity. Of the methods considered, no single method provides optimum performance for all containment types. Several methods are limited in the types of containment for which they are applicable. The results of the study to date indicate that techniques for continuous monitoring of containment integrity exist for many plants and may be implemented at modest cost

Proximal Alternating Direction Method with Relaxed Proximal Parameters for the Least Squares Covariance Adjustment Problem

Directory of Open Access Journals (Sweden)

Minghua Xu

2014-01-01

Full Text Available We consider the problem of seeking a symmetric positive semidefinite matrix in a closed convex set to approximate a given matrix. This problem may arise in several areas of numerical linear algebra or come from finance industry or statistics and thus has many applications. For solving this class of matrix optimization problems, many methods have been proposed in the literature. The proximal alternating direction method is one of those methods which can be easily applied to solve these matrix optimization problems. Generally, the proximal parameters of the proximal alternating direction method are greater than zero. In this paper, we conclude that the restriction on the proximal parameters can be relaxed for solving this kind of matrix optimization problems. Numerical experiments also show that the proximal alternating direction method with the relaxed proximal parameters is convergent and generally has a better performance than the classical proximal alternating direction method.

Variationally derived coarse mesh methods using an alternative flux representation

International Nuclear Information System (INIS)

Wojtowicz, G.; Holloway, J.P.

1995-01-01

Investigation of a previously reported variational technique for the solution of the 1-D, 1-group neutron transport equation in reactor lattices has inspired the development of a finite element formulation of the method. Compared to conventional homogenization methods in which node homogenized cross sections are used, the coefficients describing this system take on greater spatial dependence. However, the methods employ an alternative flux representation which allows the transport equation to be cast into a form whose solution has only a slow spatial variation and, hence, requires relatively few variables to describe. This alternative flux representation and the stationary property of a variational principle define a class of coarse mesh discretizations of transport theory capable of achieving order of magnitude reductions of eigenvalue and pointwise scalar flux errors as compared with diffusion theory while retaining diffusion theory's relatively low cost. Initial results of a 1-D spectral element approach are reviewed and used to motivate the finite element implementation which is more efficient and almost as accurate; one and two group results of this method are described

SCALE-6 Sensitivity/Uncertainty Methods and Covariance Data

International Nuclear Information System (INIS)

Williams, Mark L.; Rearden, Bradley T.

2008-01-01

Computational methods and data used for sensitivity and uncertainty analysis within the SCALE nuclear analysis code system are presented. The methodology used to calculate sensitivity coefficients and similarity coefficients and to perform nuclear data adjustment is discussed. A description is provided of the SCALE-6 covariance library based on ENDF/B-VII and other nuclear data evaluations, supplemented by 'low-fidelity' approximate covariances. SCALE (Standardized Computer Analyses for Licensing Evaluation) is a modular code system developed by Oak Ridge National Laboratory (ORNL) to perform calculations for criticality safety, reactor physics, and radiation shielding applications. SCALE calculations typically use sequences that execute a predefined series of executable modules to compute particle fluxes and responses like the critical multiplication factor. SCALE also includes modules for sensitivity and uncertainty (S/U) analysis of calculated responses. The S/U codes in SCALE are collectively referred to as TSUNAMI (Tools for Sensitivity and UNcertainty Analysis Methodology Implementation). SCALE-6-scheduled for release in 2008-contains significant new capabilities, including important enhancements in S/U methods and data. The main functions of TSUNAMI are to (a) compute nuclear data sensitivity coefficients and response uncertainties, (b) establish similarity between benchmark experiments and design applications, and (c) reduce uncertainty in calculated responses by consolidating integral benchmark experiments. TSUNAMI includes easy-to-use graphical user interfaces for defining problem input and viewing three-dimensional (3D) geometries, as well as an integrated plotting package.

Selection of remedial alternatives for mine sites: a multicriteria decision analysis approach.

Science.gov (United States)

Betrie, Getnet D; Sadiq, Rehan; Morin, Kevin A; Tesfamariam, Solomon

2013-04-15

The selection of remedial alternatives for mine sites is a complex task because it involves multiple criteria and often with conflicting objectives. However, an existing framework used to select remedial alternatives lacks multicriteria decision analysis (MCDA) aids and does not consider uncertainty in the selection of alternatives. The objective of this paper is to improve the existing framework by introducing deterministic and probabilistic MCDA methods. The Preference Ranking Organization Method for Enrichment Evaluation (PROMETHEE) methods have been implemented in this study. The MCDA analysis involves processing inputs to the PROMETHEE methods that are identifying the alternatives, defining the criteria, defining the criteria weights using analytical hierarchical process (AHP), defining the probability distribution of criteria weights, and conducting Monte Carlo Simulation (MCS); running the PROMETHEE methods using these inputs; and conducting a sensitivity analysis. A case study was presented to demonstrate the improved framework at a mine site. The results showed that the improved framework provides a reliable way of selecting remedial alternatives as well as quantifying the impact of different criteria on selecting alternatives. Copyright © 2013 Elsevier Ltd. All rights reserved.

Studies on analytical method and nondestructive measuring method on the sensitization of austenitic stainless steels

International Nuclear Information System (INIS)

Onimura, Kichiro; Arioka, Koji; Horai, Manabu; Noguchi, Shigeru.

1982-03-01

Austenitic stainless steels are widely used as structural materials for the machine and equipment of various kinds of plants, such as thermal power, nuclear power, and chemical plants. The machines and equipment using this kind of material, however, have the possibility of suffering corrosion damage while in service, and these damages are considered to be largely due to the sensitization of the material in sometimes. So, it is necessary to develop an analytical method for grasping the sensitization of the material more in detail and a quantitative nondestructive measuring method which is applicable to various kinds of structures in order to prevent the corrosion damage. From the above viewpoint, studies have been made on the analytical method based on the theory of diffusion of chromium in austenitic stainless steels and on Electro-Potentiokinetics Reactivation Method (EPR Method) as a nondestructive measuring method, using 304 and 316 austenitic stainless steels having different carbon contents in base metals. This paper introduces the results of EPR test on the sensitization of austenitic stainless steels and the correlation between analytical and experimental results. (author)

Sensitivity analysis of the Two Geometry Method

International Nuclear Information System (INIS)

Wichers, V.A.

1993-09-01

The Two Geometry Method (TGM) was designed specifically for the verification of the uranium enrichment of low enriched UF 6 gas in the presence of uranium deposits on the pipe walls. Complications can arise if the TGM is applied under extreme conditions, such as deposits larger than several times the gas activity, small pipe diameters less than 40 mm and low pressures less than 150 Pa. This report presents a comprehensive sensitivity analysis of the TGM. The impact of the various sources of uncertainty on the performance of the method is discussed. The application to a practical case is based on worst case conditions with regards to the measurement conditions, and on realistic conditions with respect to the false alarm probability and the non detection probability. Monte Carlo calculations were used to evaluate the sensitivity for sources of uncertainty which are experimentally inaccessible. (orig.)

A simple and cost-effective method, as an appropriate alternative for visible spectrophotometry: development of a dopamine biosensor.

Science.gov (United States)

Abbaspour, Abdolkarim; Khajehzadeh, Abdolreza; Ghaffarinejad, Ali

2009-08-01

In this study, a new, simple, fast and inexpensive method as an alternative to visible spectrophotometry is developed. In this method the cells containing the sample solution were scanned with a scanner, then the color of each cell was analyzed with software written in visual basic (VB 6) media to red, green and blue values. The cells were built by creating holes in the Plexiglas sheet. The dimensions of identical cells were examined by Cr (III) solution with known concentrations. The validity of this new method was studied by determination of dopamine (DA) without using any other reagent. The parameters which affect the system were optimized. The comparison between the current and traditional UV-Vis spectrophotometry methods was studied and the results revealed similar trends in both methods. The developed method was successfully applied to the determination of dopamine in serum and urine without using any pretreatment. Finally comparing the results obtained in the developed method showed that microwave irradiation of the solution can decrease the experimental time, increase sensitivity and improve the limit of detection.

An alternative extragradient projection method for quasi-equilibrium problems.

Science.gov (United States)

Chen, Haibin; Wang, Yiju; Xu, Yi

2018-01-01

For the quasi-equilibrium problem where the players' costs and their strategies both depend on the rival's decisions, an alternative extragradient projection method for solving it is designed. Different from the classical extragradient projection method whose generated sequence has the contraction property with respect to the solution set, the newly designed method possesses an expansion property with respect to a given initial point. The global convergence of the method is established under the assumptions of pseudomonotonicity of the equilibrium function and of continuity of the underlying multi-valued mapping. Furthermore, we show that the generated sequence converges to the nearest point in the solution set to the initial point. Numerical experiments show the efficiency of the method.

Validation of Alternative In Vitro Methods to Animal Testing: Concepts, Challenges, Processes and Tools.

Science.gov (United States)

Griesinger, Claudius; Desprez, Bertrand; Coecke, Sandra; Casey, Warren; Zuang, Valérie

This chapter explores the concepts, processes, tools and challenges relating to the validation of alternative methods for toxicity and safety testing. In general terms, validation is the process of assessing the appropriateness and usefulness of a tool for its intended purpose. Validation is routinely used in various contexts in science, technology, the manufacturing and services sectors. It serves to assess the fitness-for-purpose of devices, systems, software up to entire methodologies. In the area of toxicity testing, validation plays an indispensable role: "alternative approaches" are increasingly replacing animal models as predictive tools and it needs to be demonstrated that these novel methods are fit for purpose. Alternative approaches include in vitro test methods, non-testing approaches such as predictive computer models up to entire testing and assessment strategies composed of method suites, data sources and decision-aiding tools. Data generated with alternative approaches are ultimately used for decision-making on public health and the protection of the environment. It is therefore essential that the underlying methods and methodologies are thoroughly characterised, assessed and transparently documented through validation studies involving impartial actors. Importantly, validation serves as a filter to ensure that only test methods able to produce data that help to address legislative requirements (e.g. EU's REACH legislation) are accepted as official testing tools and, owing to the globalisation of markets, recognised on international level (e.g. through inclusion in OECD test guidelines). Since validation creates a credible and transparent evidence base on test methods, it provides a quality stamp, supporting companies developing and marketing alternative methods and creating considerable business opportunities. Validation of alternative methods is conducted through scientific studies assessing two key hypotheses, reliability and relevance of the

Design Optimization Method for Composite Components Based on Moment Reliability-Sensitivity Criteria

Science.gov (United States)

Sun, Zhigang; Wang, Changxi; Niu, Xuming; Song, Yingdong

2017-08-01

In this paper, a Reliability-Sensitivity Based Design Optimization (RSBDO) methodology for the design of the ceramic matrix composites (CMCs) components has been proposed. A practical and efficient method for reliability analysis and sensitivity analysis of complex components with arbitrary distribution parameters are investigated by using the perturbation method, the respond surface method, the Edgeworth series and the sensitivity analysis approach. The RSBDO methodology is then established by incorporating sensitivity calculation model into RBDO methodology. Finally, the proposed RSBDO methodology is applied to the design of the CMCs components. By comparing with Monte Carlo simulation, the numerical results demonstrate that the proposed methodology provides an accurate, convergent and computationally efficient method for reliability-analysis based finite element modeling engineering practice.

A method of the sensitivity analysis of build-up and decay of actinides

International Nuclear Information System (INIS)

Mitani, Hiroshi; Koyama, Kinji; Kuroi, Hideo

1977-07-01

To make sensitivity analysis of build-up and decay of actinides, mathematical methods related to this problem have been investigated in detail. Application of time-dependent perturbation technique and Bateman method to sensitivity analysis is mainly studied. For the purpose, a basic equation and its adjoint equation for build-up and decay of actinides are systematically solved by introducing Laplace and modified Laplace transforms and their convolution theorems. Then, the mathematical method of sensitivity analyses is formulated by the above technique; its physical significance is also discussed. Finally, application of eigenvalue-method is investigated. Sensitivity coefficients can be directly calculated by this method. (auth.)

Identification of alternative method of teaching and learning the ...

African Journals Online (AJOL)

This study examines alternative method of teaching and learning of the concept of diffusion. An improvised U-shape glass tube called ionic mobility tube was used to observed and measure the rate of movement of divalent metal ions in an aqueous medium in the absence of an electric current. The study revealed that the ...

Sensitivity of radiation methods of diagnosis of electric potentials in dielectric materials

International Nuclear Information System (INIS)

Sapozhkov, Yu.I.; Smekalin, L.F.; Yagushkin, N.I.

1985-01-01

On the base of the albedo method the characteristics of radiation methods of diagnosis of electric potentials inside dielectrics, such as sensitivity and resolution are considered. Investigations are carried out for electron energies of tens keV. It is shown that with energy growth the sensitivity to electric field in the dielectrics volume drops. The target atomic number growth reduces the sensitivity approximately 1/lnz. The albedo method resolution in the investigated energy range is constant. The results obtained testify to the usability radiation methods of the diagnosis for control of electric fields of dielectric structural materials in the course of their operation

DQM: Decentralized Quadratically Approximated Alternating Direction Method of Multipliers

Science.gov (United States)

Mokhtari, Aryan; Shi, Wei; Ling, Qing; Ribeiro, Alejandro

2016-10-01

This paper considers decentralized consensus optimization problems where nodes of a network have access to different summands of a global objective function. Nodes cooperate to minimize the global objective by exchanging information with neighbors only. A decentralized version of the alternating directions method of multipliers (DADMM) is a common method for solving this category of problems. DADMM exhibits linear convergence rate to the optimal objective but its implementation requires solving a convex optimization problem at each iteration. This can be computationally costly and may result in large overall convergence times. The decentralized quadratically approximated ADMM algorithm (DQM), which minimizes a quadratic approximation of the objective function that DADMM minimizes at each iteration, is proposed here. The consequent reduction in computational time is shown to have minimal effect on convergence properties. Convergence still proceeds at a linear rate with a guaranteed constant that is asymptotically equivalent to the DADMM linear convergence rate constant. Numerical results demonstrate advantages of DQM relative to DADMM and other alternatives in a logistic regression problem.

High School Graduation Rates:Alternative Methods and Implications

OpenAIRE

Jing Miao; Walt Haney

2004-01-01

The No Child Left Behind Act has brought great attention to the high school graduation rate as one of the mandatory accountability measures for public school systems. However, there is no consensus on how to calculate the high school graduation rate given the lack of longitudinal databases that track individual students. This study reviews literature on and practices in reporting high school graduation rates, compares graduation rate estimates yielded from alternative methods, and estimates d...

A new cell-based method for assessing the eye irritation potential of chemicals: an alternative to the Draize test.

Science.gov (United States)

Cho, Sun-A; An, Susun; Lee, Eunyoung; Shin, Kyeho; Cho, Jun-Cheol; Lee, Tae Ryong

2012-07-20

Using a human corneal cell line (HCE-T cells) and 2 evaluation criteria, we developed a new alternative method to assess the eye irritation potential of chemicals. We exposed HCE-T cells to different concentrations of 38 chemicals for 1h and measured relative cell viability (RCV) as an endpoint at each concentration. Using the RCV values, we calculated the RCV50. We also exposed HCE-T cells to 3 fixed concentrations of the 38 chemicals (5%, 0.5%, and 0.05%) for 1h and measured the RCV at each concentration. Using the RCV values at 5%, 0.5%, and 0.05%, we developed a new criterion for eye irritation potential (total eye irritation score, TEIS) and estimated the ocular irritancy. We then assessed the correlation of the results of RCV50 and TEIS with those of the Draize rabbit eye irritation. Both the RCV50 and TEIS results exhibited good positive correlations (sensitivity: 80.77%, specificity: 83.33%, and accuracy: 81.58% for TEIS; sensitivity: 73.08-76.92%, specificity: 75.00%, and accuracy: 73.68-76.32% for RCV50). We conclude that the new in vitro model using HCE-T cells is a good alternative evaluation model for the prediction of the eye irritation potential of chemicals. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Multiple predictor smoothing methods for sensitivity analysis: Description of techniques

International Nuclear Information System (INIS)

Storlie, Curtis B.; Helton, Jon C.

2008-01-01

The use of multiple predictor smoothing methods in sampling-based sensitivity analyses of complex models is investigated. Specifically, sensitivity analysis procedures based on smoothing methods employing the stepwise application of the following nonparametric regression techniques are described: (i) locally weighted regression (LOESS), (ii) additive models, (iii) projection pursuit regression, and (iv) recursive partitioning regression. Then, in the second and concluding part of this presentation, the indicated procedures are illustrated with both simple test problems and results from a performance assessment for a radioactive waste disposal facility (i.e., the Waste Isolation Pilot Plant). As shown by the example illustrations, the use of smoothing procedures based on nonparametric regression techniques can yield more informative sensitivity analysis results than can be obtained with more traditional sensitivity analysis procedures based on linear regression, rank regression or quadratic regression when nonlinear relationships between model inputs and model predictions are present

An alternative method for performing pressurized thermal shock analysis

International Nuclear Information System (INIS)

Bishop, B.A.; Meyer, T.A.; Carter, R.G.; Gamble, R.M.

1997-01-01

This paper describes how Probability of Crack Initiation and acceptable Pressurized Thermal Shock frequency were correlated with a c and summarizes several example applications, including evaluation of potential plant modifications. Plans for an industry supported pilot-plant application of the alternative Probabilistic Fracture Mechanics method for RG 1.154 are also discussed. 9 refs, 4 figs, 1 tab

An alternative method for performing pressurized thermal shock analysis

Energy Technology Data Exchange (ETDEWEB)

Bishop, B A; Meyer, T A [Westinghouse Energy Systems, Pittsburgh, PA (United States); Carter, R G [Electric Power Research Inst., Charlotte, NC (United States); Gamble, R M [Sartrex Corp., Rockville, MD (United States)

1997-09-01

This paper describes how Probability of Crack Initiation and acceptable Pressurized Thermal Shock frequency were correlated with a{sub c} and summarizes several example applications, including evaluation of potential plant modifications. Plans for an industry supported pilot-plant application of the alternative Probabilistic Fracture Mechanics method for RG 1.154 are also discussed. 9 refs, 4 figs, 1 tab.

Alternate modal combination methods in response spectrum analysis

International Nuclear Information System (INIS)

Bezler, P.; Curreri, J.R.; Wang, Y.K.; Gupta, A.K.

1990-10-01

In piping analyses using the response spectrum method Square Root of the Sum of the Squares (SRSS) with clustering between closely spaced modes is the combination procedure most commonly used to combine between the modal response components. This procedure is simple to apply and normally yields conservative estimates of the time history results. The purpose of this study is to investigate alternate methods to combine between the modal response components. These methods are mathematically based to properly account for the combination between rigid and flexible modal responses as well as closely spaced modes. The methods are those advanced by Gupta, Hadjian and Lindely-Yow to address rigid response modes and the Double Sum Combination (DSC) method and the Complete Quadratic Combination (CQC) method to account for closely spaced modes. A direct comparison between these methods as well as the SRSS procedure is made by using them to predict the response of six piping systems. The results provided by each method are compared to the corresponding time history estimates of results as well as to each other. The degree of conservatism associated with each method is characterized. 19 refs., 16 figs., 10 tabs

Deterministic methods for sensitivity and uncertainty analysis in large-scale computer models

International Nuclear Information System (INIS)

Worley, B.A.; Oblow, E.M.; Pin, F.G.; Maerker, R.E.; Horwedel, J.E.; Wright, R.Q.; Lucius, J.L.

1987-01-01

The fields of sensitivity and uncertainty analysis are dominated by statistical techniques when large-scale modeling codes are being analyzed. This paper reports on the development and availability of two systems, GRESS and ADGEN, that make use of computer calculus compilers to automate the implementation of deterministic sensitivity analysis capability into existing computer models. This automation removes the traditional limitation of deterministic sensitivity methods. The paper describes a deterministic uncertainty analysis method (DUA) that uses derivative information as a basis to propagate parameter probability distributions to obtain result probability distributions. The paper demonstrates the deterministic approach to sensitivity and uncertainty analysis as applied to a sample problem that models the flow of water through a borehole. The sample problem is used as a basis to compare the cumulative distribution function of the flow rate as calculated by the standard statistical methods and the DUA method. The DUA method gives a more accurate result based upon only two model executions compared to fifty executions in the statistical case

Methods and Algorythms of Alternatives Ranging in Managing the Telecommunication Services Guality.

Directory of Open Access Journals (Sweden)

Pham Quang Hiep

2015-07-01

Full Text Available The article deals with methods of solving the problem of ranging of alternatives in information-analytical system of managing the quality of telecommunication services rendering process. Tasks of choice are determined, in which the alternatives are as follows: states of quality of different objects in the structure of telecommunication company management. An algorithm of ranging of objects is elaborated for the case of using unstructured set of indices. The algorithm enables to determine the objects priorities and to select the best ones among them. The suggested methods may be used while elaborating the programs of improvement of telecommunication companies competitiveness.

Multivariate Models for Prediction of Human Skin Sensitization Hazard.

Science.gov (United States)

One of the lnteragency Coordinating Committee on the Validation of Alternative Method's (ICCVAM) top priorities is the development and evaluation of non-animal approaches to identify potential skin sensitizers. The complexity of biological events necessary to produce skin sensiti...

77 FR 43827 - International Workshop on Alternative Methods for Leptospira

Science.gov (United States)

2012-07-26

... recent advances and innovations in science and technology that can be applied to Leptospira vaccine... alternative methods. The workshop is open to the public at no charge with attendance limited only by the... priority. Leptospirosis affects numerous animal species including livestock, pets, and wildlife. Vaccines...

High sensitivity phase retrieval method in grating-based x-ray phase contrast imaging

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhao; Gao, Kun; Chen, Jian; Wang, Dajiang; Wang, Shenghao; Chen, Heng; Bao, Yuan; Shao, Qigang; Wang, Zhili, E-mail: wangnsrl@ustc.edu.cn [National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei 230029 (China); Zhang, Kai [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Zhu, Peiping; Wu, Ziyu, E-mail: wuzy@ustc.edu.cn [National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei 230029, China and Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China)

2015-02-15

Purpose: Grating-based x-ray phase contrast imaging is considered as one of the most promising techniques for future medical imaging. Many different methods have been developed to retrieve phase signal, among which the phase stepping (PS) method is widely used. However, further practical implementations are hindered, due to its complex scanning mode and high radiation dose. In contrast, the reverse projection (RP) method is a novel fast and low dose extraction approach. In this contribution, the authors present a quantitative analysis of the noise properties of the refraction signals retrieved by the two methods and compare their sensitivities. Methods: Using the error propagation formula, the authors analyze theoretically the signal-to-noise ratios (SNRs) of the refraction images retrieved by the two methods. Then, the sensitivities of the two extraction methods are compared under an identical exposure dose. Numerical experiments are performed to validate the theoretical results and provide some quantitative insight. Results: The SNRs of the two methods are both dependent on the system parameters, but in different ways. Comparison between their sensitivities reveals that for the refraction signal, the RP method possesses a higher sensitivity, especially in the case of high visibility and/or at the edge of the object. Conclusions: Compared with the PS method, the RP method has a superior sensitivity and provides refraction images with a higher SNR. Therefore, one can obtain highly sensitive refraction images in grating-based phase contrast imaging. This is very important for future preclinical and clinical implementations.

High sensitivity phase retrieval method in grating-based x-ray phase contrast imaging

International Nuclear Information System (INIS)

Wu, Zhao; Gao, Kun; Chen, Jian; Wang, Dajiang; Wang, Shenghao; Chen, Heng; Bao, Yuan; Shao, Qigang; Wang, Zhili; Zhang, Kai; Zhu, Peiping; Wu, Ziyu

2015-01-01

Purpose: Grating-based x-ray phase contrast imaging is considered as one of the most promising techniques for future medical imaging. Many different methods have been developed to retrieve phase signal, among which the phase stepping (PS) method is widely used. However, further practical implementations are hindered, due to its complex scanning mode and high radiation dose. In contrast, the reverse projection (RP) method is a novel fast and low dose extraction approach. In this contribution, the authors present a quantitative analysis of the noise properties of the refraction signals retrieved by the two methods and compare their sensitivities. Methods: Using the error propagation formula, the authors analyze theoretically the signal-to-noise ratios (SNRs) of the refraction images retrieved by the two methods. Then, the sensitivities of the two extraction methods are compared under an identical exposure dose. Numerical experiments are performed to validate the theoretical results and provide some quantitative insight. Results: The SNRs of the two methods are both dependent on the system parameters, but in different ways. Comparison between their sensitivities reveals that for the refraction signal, the RP method possesses a higher sensitivity, especially in the case of high visibility and/or at the edge of the object. Conclusions: Compared with the PS method, the RP method has a superior sensitivity and provides refraction images with a higher SNR. Therefore, one can obtain highly sensitive refraction images in grating-based phase contrast imaging. This is very important for future preclinical and clinical implementations

An adjoint sensitivity-based data assimilation method and its comparison with existing variational methods

Directory of Open Access Journals (Sweden)

Yonghan Choi

2014-01-01

Full Text Available An adjoint sensitivity-based data assimilation (ASDA method is proposed and applied to a heavy rainfall case over the Korean Peninsula. The heavy rainfall case, which occurred on 26 July 2006, caused torrential rainfall over the central part of the Korean Peninsula. The mesoscale convective system (MCS related to the heavy rainfall was classified as training line/adjoining stratiform (TL/AS-type for the earlier period, and back building (BB-type for the later period. In the ASDA method, an adjoint model is run backwards with forecast-error gradient as input, and the adjoint sensitivity of the forecast error to the initial condition is scaled by an optimal scaling factor. The optimal scaling factor is determined by minimising the observational cost function of the four-dimensional variational (4D-Var method, and the scaled sensitivity is added to the original first guess. Finally, the observations at the analysis time are assimilated using a 3D-Var method with the improved first guess. The simulated rainfall distribution is shifted northeastward compared to the observations when no radar data are assimilated or when radar data are assimilated using the 3D-Var method. The rainfall forecasts are improved when radar data are assimilated using the 4D-Var or ASDA method. Simulated atmospheric fields such as horizontal winds, temperature, and water vapour mixing ratio are also improved via the 4D-Var or ASDA method. Due to the improvement in the analysis, subsequent forecasts appropriately simulate the observed features of the TL/AS- and BB-type MCSs and the corresponding heavy rainfall. The computational cost associated with the ASDA method is significantly lower than that of the 4D-Var method.

Sensitivity analysis of time-dependent laminar flows

International Nuclear Information System (INIS)

Hristova, H.; Etienne, S.; Pelletier, D.; Borggaard, J.

2004-01-01

This paper presents a general sensitivity equation method (SEM) for time dependent incompressible laminar flows. The SEM accounts for complex parameter dependence and is suitable for a wide range of problems. The formulation is verified on a problem with a closed form solution obtained by the method of manufactured solution. Systematic grid convergence studies confirm the theoretical rates of convergence in both space and time. The methodology is then applied to pulsatile flow around a square cylinder. Computations show that the flow starts with symmetrical vortex shedding followed by a transition to the traditional Von Karman street (alternate vortex shedding). Simulations show that the transition phase manifests itself earlier in the sensitivity fields than in the flow field itself. Sensitivities are then demonstrated for fast evaluation of nearby flows and uncertainty analysis. (author)

On the Exploitation of Sensitivity Derivatives for Improving Sampling Methods

Science.gov (United States)

Cao, Yanzhao; Hussaini, M. Yousuff; Zang, Thomas A.

2003-01-01

Many application codes, such as finite-element structural analyses and computational fluid dynamics codes, are capable of producing many sensitivity derivatives at a small fraction of the cost of the underlying analysis. This paper describes a simple variance reduction method that exploits such inexpensive sensitivity derivatives to increase the accuracy of sampling methods. Three examples, including a finite-element structural analysis of an aircraft wing, are provided that illustrate an order of magnitude improvement in accuracy for both Monte Carlo and stratified sampling schemes.

Demodulation method for tilted fiber Bragg grating refractometer with high sensitivity

Science.gov (United States)

Pham, Xuantung; Si, Jinhai; Chen, Tao; Wang, Ruize; Yan, Lihe; Cao, Houjun; Hou, Xun

2018-05-01

In this paper, we propose a demodulation method for refractive index (RI) sensing with tilted fiber Bragg gratings (TFBGs). It operates by monitoring the TFBG cladding mode resonance "cut-off wavelengths." The idea of a "cut-off wavelength" and its determination method are introduced. The RI sensitivities of TFBGs are significantly enhanced in certain RI ranges by using our demodulation method. The temperature-induced cross sensitivity is eliminated. We also demonstrate a parallel-double-angle TFBG (PDTFBG), in which two individual TFBGs are inscribed in the fiber core in parallel using a femtosecond laser and a phase mask. The RI sensing range of the PDTFBG is significantly broader than that of a conventional single-angle TFBG. In addition, its RI sensitivity can reach 1023.1 nm/refractive index unit in the 1.4401-1.4570 RI range when our proposed demodulation method is used.

Alternate modal combination methods in response spectrum analysis

International Nuclear Information System (INIS)

Wang, Y.K.; Bezler, P.

1989-01-01

In piping analyses using the response spectrum method Square Root of the Sum of the Squares (SRSS) with clustering between closely spaced modes is the combination procedure most commonly used to combine between the modal response components. This procedure is simple to apply and normally yields conservative estimates of the time history results. The purpose of this study is to investigate alternate methods to combine between the modal response components. These methods are mathematically based to properly account for the combination between rigid and flexible modal responses as well as closely spaced modes. The methods are those advanced by Gupta, Hadjian and Lindley-Yow to address rigid response modes and the Double Sum Combination (DSC) method and the Complete Quadratic Combination (CQC) method to account for closely spaced modes. A direct comparison between these methods as well as the SRSS procedure is made by using them to predict the response of six piping systems. For two piping systems thirty-three earthquake records were considered to account for the impact of variations in the characteristics of the excitation. The results provided by each method are compared to the corresponding time history estimates of results as well as to each other. The degree of conservatism associated with each method is characterized. 7 refs., 4 figs., 2 tabs

Screening of groundwater remedial alternatives for brownfield sites: a comprehensive method integrated MCDA with numerical simulation.

Science.gov (United States)

Li, Wei; Zhang, Min; Wang, Mingyu; Han, Zhantao; Liu, Jiankai; Chen, Zhezhou; Liu, Bo; Yan, Yan; Liu, Zhu

2018-06-01

Brownfield sites pollution and remediation is an urgent environmental issue worldwide. The screening and assessment of remedial alternatives is especially complex owing to its multiple criteria that involves technique, economy, and policy. To help the decision-makers selecting the remedial alternatives efficiently, the criteria framework conducted by the U.S. EPA is improved and a comprehensive method that integrates multiple criteria decision analysis (MCDA) with numerical simulation is conducted in this paper. The criteria framework is modified and classified into three categories: qualitative, semi-quantitative, and quantitative criteria, MCDA method, AHP-PROMETHEE (analytical hierarchy process-preference ranking organization method for enrichment evaluation) is used to determine the priority ranking of the remedial alternatives and the solute transport simulation is conducted to assess the remedial efficiency. A case study was present to demonstrate the screening method in a brownfield site in Cangzhou, northern China. The results show that the systematic method provides a reliable way to quantify the priority of the remedial alternatives.

Error Parsing: An alternative method of implementing social judgment theory

OpenAIRE

Crystal C. Hall; Daniel M. Oppenheimer

2015-01-01

We present a novel method of judgment analysis called Error Parsing, based upon an alternative method of implementing Social Judgment Theory (SJT). SJT and Error Parsing both posit the same three components of error in human judgment: error due to noise, error due to cue weighting, and error due to inconsistency. In that sense, the broad theory and framework are the same. However, SJT and Error Parsing were developed to answer different questions, and thus use different m...

High sensitive quench detection method using an integrated test wire

International Nuclear Information System (INIS)

Fevrier, A.; Tavergnier, J.P.; Nithart, H.; Kiblaire, M.; Duchateau, J.L.

1981-01-01

A high sensitive quench detection method which works even in the presence of an external perturbing magnetic field is reported. The quench signal is obtained from the difference in voltages at the superconducting winding terminals and at the terminals at a secondary winding strongly coupled to the primary. The secondary winding could consist of a ''zero-current strand'' of the superconducting cable not connected to one of the winding terminals or an integrated normal test wire inside the superconducting cable. Experimental results on quench detection obtained by this method are described. It is shown that the integrated test wire method leads to efficient and sensitive quench detection, especially in the presence of an external perturbing magnetic field

The adjoint sensitivity method, a contribution to the code uncertainty evaluation

International Nuclear Information System (INIS)

Ounsy, A.; Crecy, F. de; Brun, B.

1993-01-01

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs

The adjoint sensitivity method. A contribution to the code uncertainty evaluation

International Nuclear Information System (INIS)

Ounsy, A.; Brun, B.

1993-01-01

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs

The adjoint sensitivity method. A contribution to the code uncertainty evaluation

Energy Technology Data Exchange (ETDEWEB)

Ounsy, A; Brun, B

1994-12-31

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs.

The adjoint sensitivity method, a contribution to the code uncertainty evaluation

Energy Technology Data Exchange (ETDEWEB)

Ounsy, A; Crecy, F de; Brun, B

1994-12-31

The application of the ASM (Adjoint Sensitivity Method) to thermohydraulic codes, is examined. The advantage of the method is to be very few CPU time consuming in comparison with usual approach requiring one complete code run per sensitivity determination. The mathematical aspects of the problem are first described, and the applicability of the method of the functional-type response of a thermalhydraulic model is demonstrated. On a simple example of non linear hyperbolic equation (Burgers equation) the problem has been analyzed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the Continuous ASM and the Discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the DASM constitutes a practical solution for thermalhydraulic codes. The application of the DASM to the thermalhydraulic safety code CATHARE is then presented for two examples. They demonstrate that ASM constitutes an efficient tool for the analysis of code sensitivity. (authors) 7 figs., 5 tabs., 8 refs.

Adjoint sensitivity analysis of plasmonic structures using the FDTD method.

Science.gov (United States)

Zhang, Yu; Ahmed, Osman S; Bakr, Mohamed H

2014-05-15

We present an adjoint variable method for estimating the sensitivities of arbitrary responses with respect to the parameters of dispersive discontinuities in nanoplasmonic devices. Our theory is formulated in terms of the electric field components at the vicinity of perturbed discontinuities. The adjoint sensitivities are computed using at most one extra finite-difference time-domain (FDTD) simulation regardless of the number of parameters. Our approach is illustrated through the sensitivity analysis of an add-drop coupler consisting of a square ring resonator between two parallel waveguides. The computed adjoint sensitivities of the scattering parameters are compared with those obtained using the accurate but computationally expensive central finite difference approach.

Statistical Sensitive Data Protection and Inference Prevention with Decision Tree Methods

National Research Council Canada - National Science Library

Chang, LiWu

2003-01-01

.... We consider inference as correct classification and approach it with decision tree methods. As in our previous work, sensitive data are viewed as classes of those test data and non-sensitive data are the rest attribute values...

Application of Wielandt method in continuous-energy nuclear data sensitivity analysis with RMC code

International Nuclear Information System (INIS)

Qiu Yishu; Wang Kan; She Ding

2015-01-01

The Iterated Fission Probability (IFP) method, an accurate method to estimate adjoint-weighted quantities in the continuous-energy Monte Carlo criticality calculations, has been widely used for calculating kinetic parameters and nuclear data sensitivity coefficients. By using a strategy of waiting, however, this method faces the challenge of high memory usage to store the tallies of original contributions which size is proportional to the number of particle histories in each cycle. Recently, the Wielandt method, applied by Monte Carlo code McCARD to calculate kinetic parameters, estimates adjoint fluxes in a single particle history and thus can save memory usage. In this work, the Wielandt method has been applied in Rector Monte Carlo code RMC for nuclear data sensitivity analysis. The methodology and algorithm of applying Wielandt method in estimation of adjoint-based sensitivity coefficients are discussed. Verification is performed by comparing the sensitivity coefficients calculated by Wielandt method with analytical solutions, those computed by IFP method which is also implemented in RMC code for sensitivity analysis, and those from the multi-group TSUNAMI-3D module in SCALE code package. (author)

Netlist Oriented Sensitivity Evaluation (NOSE)

Science.gov (United States)

2017-03-01

representing the official policies or endorsements, either expressed or implied, of Air Force Research Laboratory (AFRL) and the Defense Advanced Research... Heuristics for generating an alternative netlist implementation for the same logic function to achieve a better robustness measure 2...sensitivity study: 1. Tools to calculate sensitivity of netlist nodes (signals) and heuristics for generating alternative netlist implementations

A genomic biomarker signature can predict skin sensitizers using a cell-based in vitro alternative to animal tests

Directory of Open Access Journals (Sweden)

Albrekt Ann-Sofie

2011-08-01

Full Text Available Abstract Background Allergic contact dermatitis is an inflammatory skin disease that affects a significant proportion of the population. This disease is caused by an adverse immune response towards chemical haptens, and leads to a substantial economic burden for society. Current test of sensitizing chemicals rely on animal experimentation. New legislations on the registration and use of chemicals within pharmaceutical and cosmetic industries have stimulated significant research efforts to develop alternative, human cell-based assays for the prediction of sensitization. The aim is to replace animal experiments with in vitro tests displaying a higher predictive power. Results We have developed a novel cell-based assay for the prediction of sensitizing chemicals. By analyzing the transcriptome of the human cell line MUTZ-3 after 24 h stimulation, using 20 different sensitizing chemicals, 20 non-sensitizing chemicals and vehicle controls, we have identified a biomarker signature of 200 genes with potent discriminatory ability. Using a Support Vector Machine for supervised classification, the prediction performance of the assay revealed an area under the ROC curve of 0.98. In addition, categorizing the chemicals according to the LLNA assay, this gene signature could also predict sensitizing potency. The identified markers are involved in biological pathways with immunological relevant functions, which can shed light on the process of human sensitization. Conclusions A gene signature predicting sensitization, using a human cell line in vitro, has been identified. This simple and robust cell-based assay has the potential to completely replace or drastically reduce the utilization of test systems based on experimental animals. Being based on human biology, the assay is proposed to be more accurate for predicting sensitization in humans, than the traditional animal-based tests.

A genomic biomarker signature can predict skin sensitizers using a cell-based in vitro alternative to animal tests

Science.gov (United States)

2011-01-01

Background Allergic contact dermatitis is an inflammatory skin disease that affects a significant proportion of the population. This disease is caused by an adverse immune response towards chemical haptens, and leads to a substantial economic burden for society. Current test of sensitizing chemicals rely on animal experimentation. New legislations on the registration and use of chemicals within pharmaceutical and cosmetic industries have stimulated significant research efforts to develop alternative, human cell-based assays for the prediction of sensitization. The aim is to replace animal experiments with in vitro tests displaying a higher predictive power. Results We have developed a novel cell-based assay for the prediction of sensitizing chemicals. By analyzing the transcriptome of the human cell line MUTZ-3 after 24 h stimulation, using 20 different sensitizing chemicals, 20 non-sensitizing chemicals and vehicle controls, we have identified a biomarker signature of 200 genes with potent discriminatory ability. Using a Support Vector Machine for supervised classification, the prediction performance of the assay revealed an area under the ROC curve of 0.98. In addition, categorizing the chemicals according to the LLNA assay, this gene signature could also predict sensitizing potency. The identified markers are involved in biological pathways with immunological relevant functions, which can shed light on the process of human sensitization. Conclusions A gene signature predicting sensitization, using a human cell line in vitro, has been identified. This simple and robust cell-based assay has the potential to completely replace or drastically reduce the utilization of test systems based on experimental animals. Being based on human biology, the assay is proposed to be more accurate for predicting sensitization in humans, than the traditional animal-based tests. PMID:21824406

In chemico skin sensitization risk assessment of botanical ingredients.

Science.gov (United States)

Avonto, Cristina; Chittiboyina, Amar G; Sadrieh, Nakissa; Vukmanovic, Stanislav; Khan, Ikhlas A

2018-03-24

Skin sensitization risk assessment of botanical ingredients is necessary for consumers' protection and occupational hazard identification. There are currently very few available alternative methods that can assist in the evaluation of complex mixtures. Chemical methods can provide essential information in a timely manner and thus help to reduce the need for in vivo testing, and they can complement and facilitate targeted in vitro assays. In the present work, the applicability of the high-throughput screening with dansyl cysteamine (DCYA) method for the systematic evaluation of skin sensitization of complex botanicals was explored. Botanical ingredients of four unrelated plant species were obtained and tested with the high-throughput fluorescence method at three concentrations. To illustrate the minimal matrix effects of the tested extracts on the developed method, the least DCYA-reactive extract (Rosa canina) was spiked with known sensitizers at different concentrations. The data obtained from the four plant extracts and the spiking experiments with known sensitizers, suggest that the high-throughput screening-DCYA method can be successfully applied for estimating the skin sensitization potential of complex botanical matrices. This is the first report of an attempt to develop a versatile in chemico method for the rapid detection of reactive skin sensitizers in complex botanical extracts, which could complement the battery of existing validated, non-animal methods. Copyright © 2018 John Wiley & Sons, Ltd.

Analysis of Elastic-Plastic J Integrals for 3-Dimensional Cracks Using Finite Element Alternating Method

International Nuclear Information System (INIS)

Park, Jai Hak

2009-01-01

SGBEM(Symmetric Galerkin Boundary Element Method)-FEM alternating method has been proposed by Nikishkov, Park and Atluri. In the proposed method, arbitrarily shaped three-dimensional crack problems can be solved by alternating between the crack solution in an infinite body and the finite element solution without a crack. In the previous study, the SGBEM-FEM alternating method was extended further in order to solve elastic-plastic crack problems and to obtain elastic-plastic stress fields. For the elastic-plastic analysis the algorithm developed by Nikishkov et al. is used after modification. In the algorithm, the initial stress method is used to obtain elastic-plastic stress and strain fields. In this paper, elastic-plastic J integrals for three-dimensional cracks are obtained using the method. For that purpose, accurate values of displacement gradients and stresses are necessary on an integration path. In order to improve the accuracy of stress near crack surfaces, coordinate transformation and partitioning of integration domain are used. The coordinate transformation produces a transformation Jacobian, which cancels the singularity of the integrand. Using the developed program, simple three-dimensional crack problems are solved and elastic and elastic-plastic J integrals are obtained. The obtained J integrals are compared with the values obtained using a handbook solution. It is noted that J integrals obtained from the alternating method are close to the values from the handbook

Surveying immigrants without sampling frames - evaluating the success of alternative field methods.

Science.gov (United States)

Reichel, David; Morales, Laura

2017-01-01

This paper evaluates the sampling methods of an international survey, the Immigrant Citizens Survey, which aimed at surveying immigrants from outside the European Union (EU) in 15 cities in seven EU countries. In five countries, no sample frame was available for the target population. Consequently, alternative ways to obtain a representative sample had to be found. In three countries 'location sampling' was employed, while in two countries traditional methods were used with adaptations to reach the target population. The paper assesses the main methodological challenges of carrying out a survey among a group of immigrants for whom no sampling frame exists. The samples of the survey in these five countries are compared to results of official statistics in order to assess the accuracy of the samples obtained through the different sampling methods. It can be shown that alternative sampling methods can provide meaningful results in terms of core demographic characteristics although some estimates differ to some extent from the census results.

A Web-based Alternative Non-animal Method Database for Safety Cosmetic Evaluations

OpenAIRE

Kim, Seung Won; Kim, Bae-Hwan

2016-01-01

Animal testing was used traditionally in the cosmetics industry to confirm product safety, but has begun to be banned; alternative methods to replace animal experiments are either in development, or are being validated, worldwide. Research data related to test substances are critical for developing novel alternative tests. Moreover, safety information on cosmetic materials has neither been collected in a database nor shared among researchers. Therefore, it is imperative to build and share a d...

Non-animal sensitization testing: state-of-the-art.

Science.gov (United States)

Vandebriel, Rob J; van Loveren, Henk

2010-05-01

Predictive tests to identify the sensitizing properties of chemicals are carried out using animals. In the European Union timelines for phasing out many standard animal tests were established for cosmetics. Following this policy, the new European Chemicals Legislation (REACH) favors alternative methods, if validated and appropriate. In this review the authors aim to provide a state-of-the art overview of alternative methods (in silico, in chemico, and in vitro) to identify contact and respiratory sensitizing capacity and in some occasions give a measure of potency. The past few years have seen major advances in QSAR (quantitative structure-activity relationship) models where especially mechanism-based models have great potential, peptide reactivity assays where multiple parameters can be measured simultaneously, providing a more complete reactivity profile, and cell-based assays. Several cell-based assays are in development, not only using different cell types, but also several specifically developed assays such as three-dimenionally (3D)-reconstituted skin models, an antioxidant response reporter assay, determination of signaling pathways, and gene profiling. Some of these assays show relatively high sensitivity and specificity for a large number of sensitizers and should enter validation (or are indeed entering this process). Integrating multiple assays in a decision tree or integrated testing system is a next step, but has yet to be developed. Adequate risk assessment, however, is likely to require significantly more time and efforts.

Alternative sintering methods compared to conventional thermal sintering for inkjet printed silver nanoparticle ink

NARCIS (Netherlands)

Niittynen, J.; Abbel, R.; Mäntysalo, M.; Perelaer, J.; Schubert, U.S.; Lupo, D.

2014-01-01

In this contribution several alternative sintering methods are compared to traditional thermal sintering as high temperature and long process time of thermal sintering are increasing the costs of inkjet-printing and preventing the use of this technology in large scale manufacturing. Alternative

Alternative method for determining the constant offset in lidar signal

Science.gov (United States)

Vladimir A. Kovalev; Cyle Wold; Alexander Petkov; Wei Min Hao

2009-01-01

We present an alternative method for determining the total offset in lidar signal created by a daytime background-illumination component and electrical or digital offset. Unlike existing techniques, here the signal square-range-correction procedure is initially performed using the total signal recorded by lidar, without subtraction of the offset component. While...

NordVal: A Nordic system for validation of alternative microbiological methods

DEFF Research Database (Denmark)

Qvist, Sven

2007-01-01

NordVal was created in 1999 by the Nordic Committee of Senior Officials for Food Issues under the Nordic Council of Ministers. The Committee adopted the following objective for NordVal: NordVal evaluates the performance and field of application of alternative microbiological methods. This includes...... analyses of food, water, feed, animal faeces and food environmental samples in the Nordic countries. NordVal is managed by a steering group, which is appointed by the National Food Administrations in Denmark, Finland, Iceland, Norway and Sweden. The background for creation of NordVal was a Danish...... validation system (DanVal) established in 1995 to cope with a need to validate alternative methods to be used in the Danish Salmonella Action Program. The program attracted considerable attention in the other Nordic countries. NordVal has elaborated a number of documents, which describe the requirements...

76 FR 5319 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-01-31

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This proposed rule will provide flexibility to the regulated community by allowing an additional... A. Alternative Test Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A...

Sensitive high performance liquid chromatographic method for the ...

African Journals Online (AJOL)

A new simple, sensitive, cost-effective and reproducible high performance liquid chromatographic (HPLC) method for the determination of proguanil (PG) and its metabolites, cycloguanil (CG) and 4-chlorophenylbiguanide (4-CPB) in urine and plasma is described. The extraction procedure is a simple three-step process ...

Raman Microspectrometry: An Alternative Method of Age Estimation from Dentin and Cementum

Directory of Open Access Journals (Sweden)

Karuna Kumari

2017-10-01

Full Text Available Introduction: Raman spectroscopy is simple, quick, sensitive and non destructive form of tissue examination that provides vital data about the structure, molecular composition and interactions within a sample. The human hard tissues like teeth and bone are able to resist decay for long even after other tissues are lost, thus have valuable forensic importance. Aim: To ascertain the known age of the teeth by analysing dentin and cementum using Raman microspectrometry and assess the accuracy of age estimation by comparison of dentin with cementum. Materials and Methods: The sound permanent extracted tooth specimens (40 of age ranging between 12-74 years were collected and sectioned longitudinally and different dentinal and cemental areas were analysed by Raman microspectrometry. The spectra of dentin and cementum were used as predictors of age estimation. For each sample, ratios were obtained for dentin and cementum areas, and Pearson’s correlation coefficient was calculated. Ratios, which had a correlation coefficient greater than 0.40 were used for further statistical analysis. This led to selection of ratios only for dentin areas, and it allowed us to develop a regression formula. Partial Least Square (PLS regression method was used for computing our model. Results: A significant correlation was observed between the actual chronological age and predicted age of the individual using dentinal areas of the tooth. A closest to the estimated result was achieved, with an error of three years between predicted and actual chorological age. Conclusion: Raman microspectrometry may be considered as an alternative to the conventional method of age estimation and contribute to the identification of individuals.

14 CFR 39.21 - Where can I get information about FAA-approved alternative methods of compliance?

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Where can I get information about FAA-approved alternative methods of compliance? 39.21 Section 39.21 Aeronautics and Space FEDERAL AVIATION... information about FAA-approved alternative methods of compliance? Each airworthiness directive identifies the...

Skin sensitizer identification by IL-8 secretion and CD86 expression on THP-1 cells.

Science.gov (United States)

Parise, Carolina Bellini; Sá-Rocha, Vanessa Moura; Moraes, Jane Zveiter

2015-12-25

Substantial progress has been made in the development of alternative methods for skin sensitization in the last decade in several countries around the world. Brazil is experiencing an increasing concern about using animals for product development, since the publication of the Law 9605/1998, which prohibits the use of animals when an alternative method is available. In this way, an in vitro test to evaluate allergenic potential is a pressing need.This preliminary study started setting the use of myelomonocytic THP-1 cell line, according to the human cell line activation test (h-CLAT), already under validation process. We found that 48-h chemical exposure was necessary to identify 22 out of 23 sensitizers by the analyses of CD86 expression. In addition, the CD54 expression analyses presented a poor efficiency to discriminate sensitizers from non-sensitizers in our conditions. In view of these results, we looked for changes of pro-inflammatory interleukin profile. The IL-8 secretion analyses after 24-h chemical incubation seemed to be an alternative for CD54 expression assessing.Altogether, our findings showed that the combination of the analyses of CD86 expression and IL-8 secretion allowed predicting allergenicity.

Sensitivity of wildlife habitat models to uncertainties in GIS data

Science.gov (United States)

Stoms, David M.; Davis, Frank W.; Cogan, Christopher B.

1992-01-01

Decision makers need to know the reliability of output products from GIS analysis. For many GIS applications, it is not possible to compare these products to an independent measure of 'truth'. Sensitivity analysis offers an alternative means of estimating reliability. In this paper, we present a CIS-based statistical procedure for estimating the sensitivity of wildlife habitat models to uncertainties in input data and model assumptions. The approach is demonstrated in an analysis of habitat associations derived from a GIS database for the endangered California condor. Alternative data sets were generated to compare results over a reasonable range of assumptions about several sources of uncertainty. Sensitivity analysis indicated that condor habitat associations are relatively robust, and the results have increased our confidence in our initial findings. Uncertainties and methods described in the paper have general relevance for many GIS applications.

Alternative methods for measuring obesity in African American women.

Science.gov (United States)

Clark, Ashley E; Taylor, Jacquelyn Y; Wu, Chun Yi; Smith, Jennifer A

2013-03-01

The use of body mass index (BMI) may not be the most appropriate measurement tool in determining obesity in diverse populations. We studied a convenience sample of 108 African American (AA) women to determine the best method for measuring obesity in this at-risk population. The purpose of this study was to determine if percent body fat (PBF) and percent body water (PBW) could be used as alternatives to BMI in predicting obesity and risk for hypertension (HTN) among AA women. After accounting for age, BMI, and the use of anti-hypertensive medication, PBF (p = 0.0125) and PBW (p = 0.0297) were significantly associated with systolic blood pressure, while BMI was not. Likewise, PBF (p = 0.0316) was significantly associated with diastolic blood pressure, while PBW and BMI were not. Thus, health care practitioners should consider alternative anthropometric measurements such as PBF when assessing obesity in AA women.

Space-partition method for the variance-based sensitivity analysis: Optimal partition scheme and comparative study

International Nuclear Information System (INIS)

Zhai, Qingqing; Yang, Jun; Zhao, Yu

2014-01-01

Variance-based sensitivity analysis has been widely studied and asserted itself among practitioners. Monte Carlo simulation methods are well developed in the calculation of variance-based sensitivity indices but they do not make full use of each model run. Recently, several works mentioned a scatter-plot partitioning method to estimate the variance-based sensitivity indices from given data, where a single bunch of samples is sufficient to estimate all the sensitivity indices. This paper focuses on the space-partition method in the estimation of variance-based sensitivity indices, and its convergence and other performances are investigated. Since the method heavily depends on the partition scheme, the influence of the partition scheme is discussed and the optimal partition scheme is proposed based on the minimized estimator's variance. A decomposition and integration procedure is proposed to improve the estimation quality for higher order sensitivity indices. The proposed space-partition method is compared with the more traditional method and test cases show that it outperforms the traditional one

An alternative green screen keying method for film visual effects

OpenAIRE

Zhi, Jin

2015-01-01

This study focuses on a green screen keying method developed especially for film visual effects. There are a series of ways of using existing tools for creating mattes from green or blue screen plates. However, it is still a time-consuming process, and the results vary especially when it comes to retaining tiny details, such as hair and fur. This paper introduces an alternative concept and method for retaining edge details of characters on a green screen plate, also, a number of connected mat...

Hypoplastic thumb type IIIB: An alternative method for surgical repair

Directory of Open Access Journals (Sweden)

Salih Onur Basat

2014-08-01

Full Text Available Hypoplastic thumb is the second most common congenital deformity of the thumb. Thumb hypoplasia is characterized by diminished thumb size, metacarpal adduction, metacarpophalangeal joint instability, and thenar muscle hypoplasia. In the literature, different classification types of hypoplastic thumb have been used and different treatment methods described. In this case we presented an alternative palliative treatment method for a ten-year-old patient with modified Blauth's classification type IIIB hypoplastic thumb and one-year follow-up results. [Hand Microsurg 2014; 3(2.000: 59-61

The adjoint sensitivity method, a contribution to the code uncertainty evaluation

International Nuclear Information System (INIS)

Ounsy, A.; Brun, B.; De Crecy, F.

1994-01-01

This paper deals with the application of the adjoint sensitivity method (ASM) to thermal hydraulic codes. The advantage of the method is to use small central processing unit time in comparison with the usual approach requiring one complete code run per sensitivity determination. In the first part the mathematical aspects of the problem are treated, and the applicability of the method of the functional-type response of a thermal hydraulic model is demonstrated. On a simple example of non-linear hyperbolic equation (Burgers equation) the problem has been analysed. It is shown that the formalism used in the literature treating this subject is not appropriate. A new mathematical formalism circumventing the problem is proposed. For the discretized form of the problem, two methods are possible: the continuous ASM and the discrete ASM. The equivalence of both methods is demonstrated; nevertheless only the discrete ASM constitutes a practical solution for thermal hydraulic codes. The application of the discrete ASM to the thermal hydraulic safety code CATHARE is then presented for two examples. They demonstrate that the discrete ASM constitutes an efficient tool for the analysis of code sensitivity. ((orig.))

Discrimination of skin sensitizers from non-sensitizers by interleukin-1α and interleukin-6 production on cultured human keratinocytes.

Science.gov (United States)

Jung, Daun; Che, Jeong-Hwan; Lim, Kyung-Min; Chun, Young-Jin; Heo, Yong; Seok, Seung Hyeok

2016-09-01

In vitro testing methods for classifying sensitizers could be valuable alternatives to in vivo sensitization testing using animal models, such as the murine local lymph node assay (LLNA) and the guinea pig maximization test (GMT), but there remains a need for in vitro methods that are more accurate and simpler to distinguish skin sensitizers from non-sensitizers. Thus, the aim of our study was to establish an in vitro assay as a screening tool for detecting skin sensitizers using the human keratinocyte cell line, HaCaT. HaCaT cells were exposed to 16 relevant skin sensitizers and 6 skin non-sensitizers. The highest dose used was the dose causing 75% cell viability (CV75) that we determined by an MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assay. The levels of extracellular production of interleukin-1α (IL-1α) and IL-6 were measured. The sensitivity of IL-1α was 63%, specificity was 83% and accuracy was 68%. In the case of IL-6, sensitivity: 69%, specificity: 83% and accuracy: 73%. Thus, this study suggests that measuring extracellular production of pro-inflammatory cytokines IL-1α and IL-6 by human HaCaT cells may potentially classify skin sensitizers from non-sensitizers. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Alternating direction transport sweeps for linear discontinuous SN method

International Nuclear Information System (INIS)

Yavuz, M.; Aykanat, C.

1993-01-01

The performance of Alternating Direction Transport Sweep (ADTS) method is investigated for spatially differenced Linear Discontinuous S N (LD-S N ) problems on a MIMD multicomputer, Intel IPSC/2. The method consists of dividing a transport problem spatially into sub-problems, assigning each sub-problem to a separate processor. Then, the problem is solved by performing transport sweeps iterating on the scattering source and interface fluxes between the sub-problems. In each processor, the order of transport sweeps is scheduled such that a processor completing its computation in a quadrant of a transport sweep is able to use the most recent information (exiting fluxes of neighboring processor) as its incoming fluxes to start the next quadrant calculation. Implementation of this method on the Intel IPSC/2 multicomputer displays significant speedups over the one-processor method. Also, the performance of the method is compared with those reported previously for the Diamond Differenced S N (DD-S N ) method. Our experimental experience illustrates that the parallel performance of both the ADTS LD- and DD-S N methods is the same. (orig.)

Innovative Teaching Practice: Traditional and Alternative Methods (Challenges and Implications)

Science.gov (United States)

Nurutdinova, Aida R.; Perchatkina, Veronika G.; Zinatullina, Liliya M.; Zubkova, Guzel I.; Galeeva, Farida T.

2016-01-01

The relevance of the present issue is caused be the strong need in alternative methods of learning foreign language and the need in language training and retraining for the modern professionals. The aim of the article is to identify the basic techniques and skills in using various modern techniques in the context of modern educational tasks. The…

Application of Monte Carlo filtering method in regional sensitivity analysis of AASHTOWare Pavement ME design

Directory of Open Access Journals (Sweden)

Zhong Wu

2017-04-01

Full Text Available Since AASHTO released the Mechanistic-Empirical Pavement Design Guide (MEPDG for public review in 2004, many highway research agencies have performed sensitivity analyses using the prototype MEPDG design software. The information provided by the sensitivity analysis is essential for design engineers to better understand the MEPDG design models and to identify important input parameters for pavement design. In literature, different studies have been carried out based on either local or global sensitivity analysis methods, and sensitivity indices have been proposed for ranking the importance of the input parameters. In this paper, a regional sensitivity analysis method, Monte Carlo filtering (MCF, is presented. The MCF method maintains many advantages of the global sensitivity analysis, while focusing on the regional sensitivity of the MEPDG model near the design criteria rather than the entire problem domain. It is shown that the information obtained from the MCF method is more helpful and accurate in guiding design engineers in pavement design practices. To demonstrate the proposed regional sensitivity method, a typical three-layer flexible pavement structure was analyzed at input level 3. A detailed procedure to generate Monte Carlo runs using the AASHTOWare Pavement ME Design software was provided. The results in the example show that the sensitivity ranking of the input parameters in this study reasonably matches with that in a previous study under a global sensitivity analysis. Based on the analysis results, the strengths, practical issues, and applications of the MCF method were further discussed.

Sensitivity analysis of a complex, proposed geologic waste disposal system using the Fourier Amplitude Sensitivity Test method

International Nuclear Information System (INIS)

Lu Yichi; Mohanty, Sitakanta

2001-01-01

The Fourier Amplitude Sensitivity Test (FAST) method has been used to perform a sensitivity analysis of a computer model developed for conducting total system performance assessment of the proposed high-level nuclear waste repository at Yucca Mountain, Nevada, USA. The computer model has a large number of random input parameters with assigned probability density functions, which may or may not be uniform, for representing data uncertainty. The FAST method, which was previously applied to models with parameters represented by the uniform probability distribution function only, has been modified to be applied to models with nonuniform probability distribution functions. Using an example problem with a small input parameter set, several aspects of the FAST method, such as the effects of integer frequency sets and random phase shifts in the functional transformations, and the number of discrete sampling points (equivalent to the number of model executions) on the ranking of the input parameters have been investigated. Because the number of input parameters of the computer model under investigation is too large to be handled by the FAST method, less important input parameters were first screened out using the Morris method. The FAST method was then used to rank the remaining parameters. The validity of the parameter ranking by the FAST method was verified using the conditional complementary cumulative distribution function (CCDF) of the output. The CCDF results revealed that the introduction of random phase shifts into the functional transformations, proposed by previous investigators to disrupt the repetitiveness of search curves, does not necessarily improve the sensitivity analysis results because it destroys the orthogonality of the trigonometric functions, which is required for Fourier analysis

Further development of LLNA:DAE method as stand-alone skin-sensitization testing method and applied for evaluation of relative skin-sensitizing potency between chemicals.

Science.gov (United States)

Yamashita, Kunihiko; Shinoda, Shinsuke; Hagiwara, Saori; Itagaki, Hiroshi

2015-04-01

To date, there has been no well-established local lymph node assay (LLNA) that includes an elicitation phase. Therefore, we developed a modified local lymph node assay with an elicitation phase (LLNA:DAE) to discriminate true skin sensitizers from chemicals that gave borderline positive results and previously reported this assay. To develop the LLNA:DAE method as a useful stand-alone testing method, we investigated the complete procedure for the LLNA:DAE method using hexyl cinnamic aldehyde (HCA), isoeugenol, and 2,4-dinitrochlorobenzene (DNCB) as test compounds. We defined the LLNA:DAE procedure as follows: in the dose-finding test, four concentrations of chemical applied to dorsum of the right ear on days 1, 2, and 3 and dorsum of both ears on day 10. Ear thickness and skin irritation score were measured on days 1, 3, 5, 10, and 12. Local lymph nodes were excised and weighed on day 12. The test dose for the primary LLNA:DAE study was selected as the dose that gave the highest left ear lymph node weight in the dose-finding study, or the lowest dose that produced a left ear lymph node of over 4 mg. This procedure was validated using nine different chemicals. Furthermore, qualitative relationship was observed between the degree of elicitation response in the left ear lymph node and the skin sensitizing potency of 32 chemicals tested in this study and the previous study. These results indicated that LLNA:DAE method was as first LLNA method that was able to evaluate the skin sensitizing potential and potency in elicitation response.

A Sensitive Validated Spectrophotometric Method for the Determination of Flucloxacillin Sodium

Directory of Open Access Journals (Sweden)

R. Singh Gujral

2009-01-01

Full Text Available A simple and sensitive spectrophotometric method has been proposed for the determination of flucloxacillin sodium. The determination method is based on charge transfer complexation reaction of the drug with iodine in methanol-dichloromethane medium. The absorbance was measured at 362 nm against the reagent blank. Under optimized experimental conditions, Beer's law is obeyed in the concentration ranges 1-9 μg/mL for flucloxacillin. The method was validated for specificity, linearity, precision, accuracy. The degree of linearity of the calibration curves, the percent recoveries, limit of detection and quantitation for the spectrophotometric method were determined. No interferences could be observed from the additives commonly present in the pharmaceutical formulations. The method was successfully applied for in vitro determination of human urine samples with low RSD value. This is simple, specific, accurate and sensitive spectrophotometric method.

A combination between the differential and the perturbation theory methods for calculating sensitivity coefficients

International Nuclear Information System (INIS)

Borges, Antonio Andrade

1998-01-01

A new method for the calculation of sensitivity coefficients is developed. The new method is a combination of two methodologies used for calculating theses coefficients, which are the differential and the generalized perturbation theory methods. The method utilizes as integral parameter the average flux in an arbitrary region of the system. Thus, the sensitivity coefficient contains only the component corresponding to the neutron flux. To obtain the new sensitivity coefficient, the derivatives of the integral parameter, Φ, with respect to σ are calculated using the perturbation method and the functional derivatives of this generic integral parameter with respect to σ and Φ are calculated using the differential method. (author)

Radioactive waste management alternatives

International Nuclear Information System (INIS)

Baranowski, F.P.

1976-01-01

The information in the US ERDA ''Technical Alternatives Document'' is summarized. The first two points show that waste treatment, interim storage and transportation technologies for all wastes are currently available. Third, an assessment of integrated waste management systems is needed. One such assessment will be provided in our expanded waste management environmental statement currently planned for release in about one year. Fourth, geologies expected to be suitable for final geologic storage are known. Fifth, repository system assessment methods, that is a means to determine and assess the acceptability of a terminal storage facility for nonretrievable storage, must and will be prepared. Sixth, alternatives to geologic storage are not now available. Seventh, waste quantities and characteristics are sensitive to technologies and fuel-cycle modes, and therefore an assessment of these technologies and modes is important. Eighth, and most important, it is felt that the LWR fuel cycle can be closed with current technologies

Complementary and Alternative Medicine Methods in Chronic Renal Failure

Directory of Open Access Journals (Sweden)

Zeynep Erdogan

2014-08-01

Full Text Available Despite its long history, use of complementary and alternative medicine (CAM methods has increased dramatically only after 1990s. Up to 57% of patients with chronic renal use CAM methods.These patienys use CAM methods to overcome hypertension, fatigue, constipation, leg edema, pain, cramps, anxiety, depression, sleep disorders, to cope with symptoms such as itching, to stop the progression of kidney disease and to improve their quality of life. Methods used are herbal products and food supplements, acupressure, acupuncture, homeopathy, exercise, aromatherapy, yoga and reflexology. Nephrotoxic effect of several CAM therapies used in patients with renal impairment could disturb hemodynamics by reducing the glomerular filtration rate. For this reason, health care providers should question patients about used of CAM, methods. Communication with patients should be clear and should not act judgmental. Health care personnel should learn more about CAM methods in order to avoid unwanted situations that could develop after the application of CAM methods. Patients should be informed correctly and scientifically about these methods to avoid harmful and unnecessary uses. [Archives Medical Review Journal 2014; 23(4.000: 770-786

Sensitivity analysis using probability bounding

International Nuclear Information System (INIS)

Ferson, Scott; Troy Tucker, W.

2006-01-01

Probability bounds analysis (PBA) provides analysts a convenient means to characterize the neighborhood of possible results that would be obtained from plausible alternative inputs in probabilistic calculations. We show the relationship between PBA and the methods of interval analysis and probabilistic uncertainty analysis from which it is jointly derived, and indicate how the method can be used to assess the quality of probabilistic models such as those developed in Monte Carlo simulations for risk analyses. We also illustrate how a sensitivity analysis can be conducted within a PBA by pinching inputs to precise distributions or real values

Alternative methods of salt disposal at the seven salt sites for a nuclear waste repository

International Nuclear Information System (INIS)

1987-02-01

This study discusses the various alternative salt management techniques for the disposal of excess mined salt at seven potentially acceptable nuclear waste repository sites: Deaf Smith and Swisher Counties, Texas; Richton and Cypress Creek Domes, Mississippi; Vacherie Dome, Louisiana; and Davis and Lavender Canyons, Utah. Because the repository development involves the underground excavation of corridors and waste emplacement rooms, in either bedded or domed salt formations, excess salt will be mined and must be disposed of offsite. The salt disposal alternatives examined for all the sites include commercial use, ocean disposal, deep well injection, landfill disposal, and underground mine disposal. These alternatives (and other site-specific disposal methods) are reviewed, using estimated amounts of excavated, backfilled, and excess salt. Methods of transporting the excess salt are discussed, along with possible impacts of each disposal method and potential regulatory requirements. A preferred method of disposal is recommended for each potentially acceptable repository site. 14 refs., 5 tabs

Input-constrained model predictive control via the alternating direction method of multipliers

DEFF Research Database (Denmark)

Sokoler, Leo Emil; Frison, Gianluca; Andersen, Martin S.

2014-01-01

This paper presents an algorithm, based on the alternating direction method of multipliers, for the convex optimal control problem arising in input-constrained model predictive control. We develop an efficient implementation of the algorithm for the extended linear quadratic control problem (LQCP......) with input and input-rate limits. The algorithm alternates between solving an extended LQCP and a highly structured quadratic program. These quadratic programs are solved using a Riccati iteration procedure, and a structure-exploiting interior-point method, respectively. The computational cost per iteration...... is quadratic in the dimensions of the controlled system, and linear in the length of the prediction horizon. Simulations show that the approach proposed in this paper is more than an order of magnitude faster than several state-of-the-art quadratic programming algorithms, and that the difference in computation...

Method and apparatus for formation logging using position sensitive neutron detectors

International Nuclear Information System (INIS)

Gadken, L.L.

1986-01-01

This patent describes a method for logging earth formations using position sensitive neutron detectors. The method consists of: 1) Irradiation of earth formations in the vicinity of a well borehole with a source of fast neutrons. 2) At four longitudinally spaced distances from the neutron source in the borehole, the epithermal neutron population is detected. Each of the four separate populations is detected in an epithermally sensitive and substantially thermally insensitive portion of the same position sensitive neutron detector. A representative signal from each is then individually generated. 3) First, second, third, and fourth neutron population representative signals are combined. They derive a simultaneous measurement signal. This signal is functionally related to the porosity and also a signal functionally related to a neutron characteristic length of the earth formations in the vicinity of the borehole

Procedures for Sensitive Immunoassay

Energy Technology Data Exchange (ETDEWEB)

Givol, D. [Department of Chemical Immunology, Weizmann Institute of Science, Rehovot (Israel)

1970-02-15

Sensitive immunoassay methods should be applied to small molecules of biological importance, which are non-immunogenic by themselves, such as small peptide hormones (e.g. bradykinin), plant hormones (e.g. indoleacetic acid), nucleotides and other small molecules. Methods of binding these small molecules, as haptens, to immunogenic carriers by various cross-linking agents are described (dicyclohexylcarbodiimide, tolylene-diisocyanate and glutaraldehyde), and the considerations involved in relation to the methods of binding and the specificity of the antibodies formed are discussed. Some uses of antibody bound to bromoacetyl cellulose as an immuno adsorbent convenient for assay of immunoglobulins are described. Finally, the sensitive immunoassay method of chemically modified phage is described. This includes methods of binding small molecules (such as the dinitrophenyl group, penicillin, indoleacetic acid) or proteins (such as insulin, immunoglobulins) to phages. Methods of direct chemical conjugation, or an indirect binding via anti-phage Fab, are described. The phage inactivation method by direct plating and its modifications (such as decision technique and complex inactivation) are compared with the more simple end-point titration method. The inhibition of phage inactivation has some advantages as it does not require radioactive material, or expensive radioactive counters, and avoids the need for separation between bound and unbound antigen. Hence, if developed, it could be used as an alternative to radioimmunoassay. (author)

An alternative plutonium disposition method

International Nuclear Information System (INIS)

Kueppers, C.

2002-01-01

This paper provides a feasibility study on vitrification of plutonium with high active waste concentrate, and fabrication of MOX fuel rods for direct final disposal. These are potential alternatives to the direct use of MOX fuel in a reactor. (author)

A combination of differential method and perturbation theory for the calculation of sensitivity coefficients

International Nuclear Information System (INIS)

Santos, Adimir dos; Borges, A.A.

2000-01-01

A new method for the calculation of sensitivity coefficients is developed. The new method is a combination of two methodologies used for calculating these coefficients, which are the differential and the generalized perturbation theory methods. The proposed method utilizes as integral parameter the average flux in an arbitrary region of the system. Thus, the sensitivity coefficient contains only the component corresponding to the neutron flux. To obtain the new sensitivity coefficient, the derivates of the integral parameter, φ(ξ), with respect to σ are calculated using the perturbation method and the functional derivates of this generic integral parameter with respect to σ and φ are calculated using the differential method. The new method merges the advantages of the differential and generalized perturbation theory methods and eliminates their disadvantages. (author)

77 FR 2064 - Availability of the Report on the International Workshop on Alternative Methods To Reduce, Refine...

Science.gov (United States)

2012-01-13

... Validation of Alternative Methods, and Health Canada. The workshop was co-sponsored by the Society of... Coordinating Committee on the Validation of Alternative Methods (ICCVAM), an interagency committee of the... prioritize research, development, and validation efforts needed to address these knowledge and data gaps in...

Noninvasive determination of optical lever sensitivity in atomic force microscopy

International Nuclear Information System (INIS)

Higgins, M.J.; Proksch, R.; Sader, J.E.; Polcik, M.; Mc Endoo, S.; Cleveland, J.P.; Jarvis, S.P.

2006-01-01

Atomic force microscopes typically require knowledge of the cantilever spring constant and optical lever sensitivity in order to accurately determine the force from the cantilever deflection. In this study, we investigate a technique to calibrate the optical lever sensitivity of rectangular cantilevers that does not require contact to be made with a surface. This noncontact approach utilizes the method of Sader et al. [Rev. Sci. Instrum. 70, 3967 (1999)] to calibrate the spring constant of the cantilever in combination with the equipartition theorem [J. L. Hutter and J. Bechhoefer, Rev. Sci. Instrum. 64, 1868 (1993)] to determine the optical lever sensitivity. A comparison is presented between sensitivity values obtained from conventional static mode force curves and those derived using this noncontact approach for a range of different cantilevers in air and liquid. These measurements indicate that the method offers a quick, alternative approach for the calibration of the optical lever sensitivity

Noninvasive determination of optical lever sensitivity in atomic force microscopy

Science.gov (United States)

Higgins, M. J.; Proksch, R.; Sader, J. E.; Polcik, M.; Mc Endoo, S.; Cleveland, J. P.; Jarvis, S. P.

2006-01-01

Atomic force microscopes typically require knowledge of the cantilever spring constant and optical lever sensitivity in order to accurately determine the force from the cantilever deflection. In this study, we investigate a technique to calibrate the optical lever sensitivity of rectangular cantilevers that does not require contact to be made with a surface. This noncontact approach utilizes the method of Sader et al. [Rev. Sci. Instrum. 70, 3967 (1999)] to calibrate the spring constant of the cantilever in combination with the equipartition theorem [J. L. Hutter and J. Bechhoefer, Rev. Sci. Instrum. 64, 1868 (1993)] to determine the optical lever sensitivity. A comparison is presented between sensitivity values obtained from conventional static mode force curves and those derived using this noncontact approach for a range of different cantilevers in air and liquid. These measurements indicate that the method offers a quick, alternative approach for the calibration of the optical lever sensitivity.

Distributed Evaluation of Local Sensitivity Analysis (DELSA), with application to hydrologic models

Science.gov (United States)

Rakovec, O.; Hill, M. C.; Clark, M. P.; Weerts, A. H.; Teuling, A. J.; Uijlenhoet, R.

2014-01-01

This paper presents a hybrid local-global sensitivity analysis method termed the Distributed Evaluation of Local Sensitivity Analysis (DELSA), which is used here to identify important and unimportant parameters and evaluate how model parameter importance changes as parameter values change. DELSA uses derivative-based "local" methods to obtain the distribution of parameter sensitivity across the parameter space, which promotes consideration of sensitivity analysis results in the context of simulated dynamics. This work presents DELSA, discusses how it relates to existing methods, and uses two hydrologic test cases to compare its performance with the popular global, variance-based Sobol' method. The first test case is a simple nonlinear reservoir model with two parameters. The second test case involves five alternative "bucket-style" hydrologic models with up to 14 parameters applied to a medium-sized catchment (200 km2) in the Belgian Ardennes. Results show that in both examples, Sobol' and DELSA identify similar important and unimportant parameters, with DELSA enabling more detailed insight at much lower computational cost. For example, in the real-world problem the time delay in runoff is the most important parameter in all models, but DELSA shows that for about 20% of parameter sets it is not important at all and alternative mechanisms and parameters dominate. Moreover, the time delay was identified as important in regions producing poor model fits, whereas other parameters were identified as more important in regions of the parameter space producing better model fits. The ability to understand how parameter importance varies through parameter space is critical to inform decisions about, for example, additional data collection and model development. The ability to perform such analyses with modest computational requirements provides exciting opportunities to evaluate complicated models as well as many alternative models.

Final Rule: NESHAP for the Portland Cement Manufacturing Industry: Alternative Monitoring Method

Science.gov (United States)

EPA is extending its approval for the use of an alternative method to show compliance with hydrogen chloride (HCl) emissions limits in the National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry

Sensitivity Analysis of Dynamic Tariff Method for Congestion Management in Distribution Networks

DEFF Research Database (Denmark)

Huang, Shaojun; Wu, Qiuwei; Liu, Zhaoxi

2015-01-01

The dynamic tariff (DT) method is designed for the distribution system operator (DSO) to alleviate the congestions that might occur in a distribution network with high penetration of distribute energy resources (DERs). Sensitivity analysis of the DT method is crucial because of its decentralized...... control manner. The sensitivity analysis can obtain the changes of the optimal energy planning and thereby the line loading profiles over the infinitely small changes of parameters by differentiating the KKT conditions of the convex quadratic programming, over which the DT method is formed. Three case...

Alternative microbial methods: An overview and selection criteria.

Science.gov (United States)

Jasson, Vicky; Jacxsens, Liesbeth; Luning, Pieternel; Rajkovic, Andreja; Uyttendaele, Mieke

2010-09-01

This study provides an overview and criteria for the selection of a method, other than the reference method, for microbial analysis of foods. In a first part an overview of the general characteristics of rapid methods available, both for enumeration and detection, is given with reference to relevant bibliography. Perspectives on future development and the potential of the rapid method for routine application in food diagnostics are discussed. As various alternative "rapid" methods in different formats are available on the market, it can be very difficult for a food business operator or for a control authority to select the most appropriate method which fits its purpose. Validation of a method by a third party, according to international accepted protocol based upon ISO 16140, may increase the confidence in the performance of a method. A list of at the moment validated methods for enumeration of both utility indicators (aerobic plate count) and hygiene indicators (Enterobacteriaceae, Escherichia coli, coagulase positive Staphylococcus) as well as for detection of the four major pathogens (Salmonella spp., Listeria monocytogenes, E. coli O157 and Campylobacter spp.) is included with reference to relevant websites to check for updates. In a second part of this study, selection criteria are introduced to underpin the choice of the appropriate method(s) for a defined application. The selection criteria link the definition of the context in which the user of the method functions - and thus the prospective use of the microbial test results - with the technical information on the method and its operational requirements and sustainability. The selection criteria can help the end user of the method to obtain a systematic insight into all relevant factors to be taken into account for selection of a method for microbial analysis. Copyright 2010 Elsevier Ltd. All rights reserved.

Sensitivity analysis for decision-making using the MORE method-A Pareto approach

International Nuclear Information System (INIS)

Ravalico, Jakin K.; Maier, Holger R.; Dandy, Graeme C.

2009-01-01

Integrated Assessment Modelling (IAM) incorporates knowledge from different disciplines to provide an overarching assessment of the impact of different management decisions. The complex nature of these models, which often include non-linearities and feedback loops, requires special attention for sensitivity analysis. This is especially true when the models are used to form the basis of management decisions, where it is important to assess how sensitive the decisions being made are to changes in model parameters. This research proposes an extension to the Management Option Rank Equivalence (MORE) method of sensitivity analysis; a new method of sensitivity analysis developed specifically for use in IAM and decision-making. The extension proposes using a multi-objective Pareto optimal search to locate minimum combined parameter changes that result in a change in the preferred management option. It is demonstrated through a case study of the Namoi River, where results show that the extension to MORE is able to provide sensitivity information for individual parameters that takes into account simultaneous variations in all parameters. Furthermore, the increased sensitivities to individual parameters that are discovered when joint parameter variation is taken into account shows the importance of ensuring that any sensitivity analysis accounts for these changes.

An efficient method of reducing glass dispersion tolerance sensitivity

Science.gov (United States)

Sparrold, Scott W.; Shepard, R. Hamilton

2014-12-01

Constraining the Seidel aberrations of optical surfaces is a common technique for relaxing tolerance sensitivities in the optimization process. We offer an observation that a lens's Abbe number tolerance is directly related to the magnitude by which its longitudinal and transverse color are permitted to vary in production. Based on this observation, we propose a computationally efficient and easy-to-use merit function constraint for relaxing dispersion tolerance sensitivity. Using the relationship between an element's chromatic aberration and dispersion sensitivity, we derive a fundamental limit for lens scale and power that is capable of achieving high production yield for a given performance specification, which provides insight on the point at which lens splitting or melt fitting becomes necessary. The theory is validated by comparing its predictions to a formal tolerance analysis of a Cooke Triplet, and then applied to the design of a 1.5x visible linescan lens to illustrate optimization for reduced dispersion sensitivity. A selection of lenses in high volume production is then used to corroborate the proposed method of dispersion tolerance allocation.

Correlation expansion: a powerful alternative multiple scattering calculation method

International Nuclear Information System (INIS)

Zhao Haifeng; Wu Ziyu; Sebilleau, Didier

2008-01-01

We introduce a powerful alternative expansion method to perform multiple scattering calculations. In contrast to standard MS series expansion, where the scattering contributions are grouped in terms of scattering order and may diverge in the low energy region, this expansion, called correlation expansion, partitions the scattering process into contributions from different small atom groups and converges at all energies. It converges faster than MS series expansion when the latter is convergent. Furthermore, it takes less memory than the full MS method so it can be used in the near edge region without any divergence problem, even for large clusters. The correlation expansion framework we derive here is very general and can serve to calculate all the elements of the scattering path operator matrix. Photoelectron diffraction calculations in a cluster containing 23 atoms are presented to test the method and compare it to full MS and standard MS series expansion

ALTERNATIVE FIELD METHODS TO TREAT MERCURY IN SOIL

Energy Technology Data Exchange (ETDEWEB)

Ernest F. Stine Jr; Steven T. Downey

2002-08-14

U.S. Department of Energy (DOE) used large quantities of mercury in the uranium separating process from the 1950s until the late 1980s in support of national defense. Some of this mercury, as well as other hazardous metals and radionuclides, found its way into, and under, several buildings, soil and subsurface soils and into some of the surface waters. Several of these areas may pose potential health or environmental risks and must be dealt with under current environmental regulations. DOE's National Energy Technology Laboratory (NETL) awarded a contract ''Alternative Field Methods to Treat Mercury in Soil'' to IT Group, Knoxville TN (IT) and its subcontractor NFS, Erwin, TN to identify remedial methods to clean up mercury-contaminated high-clay content soils using proven treatment chemistries. The sites of interest were the Y-12 National Security Complex located in Oak Ridge, Tennessee, the David Witherspoon properties located in Knoxville, Tennessee, and at other similarly contaminated sites. The primary laboratory-scale contract objectives were (1) to safely retrieve and test samples of contaminated soil in an approved laboratory and (2) to determine an acceptable treatment method to ensure that the mercury does not leach from the soil above regulatory levels. The leaching requirements were to meet the TC (0.2 mg/l) and UTS (0.025 mg/l) TCLP criteria. In-situ treatments were preferred to control potential mercury vapors emissions and liquid mercury spills associated with ex-situ treatments. All laboratory work was conducted in IT's and NFS laboratories. Mercury contaminated nonradioactive soil from under the Alpha 2 building in the Y-12 complex was used. This soils contained insufficient levels of leachable mercury and resulted in TCLP mercury concentrations that were similar to the applicable LDR limits. The soil was spiked at multiple levels with metallic (up to 6000 mg/l) and soluble mercury compounds (up to 500 mg/kg) to

A highly sensitive method for detection of molybdenum-containing proteins

International Nuclear Information System (INIS)

Kalakutskii, K.L.; Shvetsov, A.A.; Bursakov, S.A.; Letarov, A.V.; Zabolotnyi, A.I.; L'vov, N.P.

1992-01-01

A highly sensitive method for detection of molybdenum-containing proteins in gels after electrophoresis has been developed. The method involves in vitro labeling of the proteins with the radioactive isotope 185 W. The method used to detect molybdenum-accumulating proteins in lupine seeds, xanthine dehydrogenase and another molybdenum-containing protein in wheat, barley, and pea seedlings, and nitrate reductase and xanthine dehydrogenase in bacteroides from lupine nodules. Nitrogenase could not be detected by the method. 16 refs., 5 figs

Perspectives and strategies of alternative methods used in the risk assessment of personal care products.

Science.gov (United States)

Quantin, P; Thélu, A; Catoire, S; Ficheux, H

2015-11-01

Risk assessment for personal care products requires the use of alternative methods since animal testing is now totally banned. Some of these methods are effective and have been validated by the "European Union Reference Laboratory for alternatives to animal testing"; but there is still a need for development and implementation of methods for specific endpoints. In this review, we have focused on dermal risk assessment because it is the prime route of absorption and main target organ for personal care products. Within this field, various areas must be assessed: irritation, sensitisation and toxicokinetic. Personal care product behaviour after use by the consumer and potential effects on the environment are also discussed. The purpose of this review is to show evolution and the prospects of alternative methods for safety dermal assessment. Assessment strategies must be adapted to the different chemical classes of substances studied but also to the way in which they are used. Finally, experimental and theoretical technical parameters that may impact on measured effects have been identified and discussed. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

A simple method to estimate the episode and programme sensitivity of breast cancer screening programmes.

Science.gov (United States)

Zorzi, Manuel; Guzzinati, Stefano; Puliti, Donella; Paci, Eugenio

2010-01-01

The estimation of breast cancer screening sensitivity is a major aim in the quality assessment of screening programmes. The proportional incidence method for the estimation of the sensitivity of breast cancer screening programmes is rarely used to estimate the underlying incidence rates. We present a method to estimate episode and programme sensitivity of screening programmes, based solely on cancers detected within screening cycles (excluding breast cancer cases at prevalent screening round) and on the number of incident cases in the total target population (steady state). The assumptions, strengths and limitations of the method are discussed. An example of calculation of episode and programme sensitivities is given, on the basis of the data from the IMPACT study, a large observational study of breast cancer screening programmes in Italy. The programme sensitivity from the fifth year of screening onwards ranged between 41% and 48% of the total number of cases in the target population. At steady state episode sensitivity was 0.70, with a trend across age groups, with lowest values in women aged 50-54 years (0.52) and highest in those 65-69 (0.77). The method is a very serviceable tool for estimating sensitivity in service screening programmes, and the results are comparable with those of other methods of estimation.

Sensitivity evaluation of dynamic speckle activity measurements using clustering methods

International Nuclear Information System (INIS)

Etchepareborda, Pablo; Federico, Alejandro; Kaufmann, Guillermo H.

2010-01-01

We evaluate and compare the use of competitive neural networks, self-organizing maps, the expectation-maximization algorithm, K-means, and fuzzy C-means techniques as partitional clustering methods, when the sensitivity of the activity measurement of dynamic speckle images needs to be improved. The temporal history of the acquired intensity generated by each pixel is analyzed in a wavelet decomposition framework, and it is shown that the mean energy of its corresponding wavelet coefficients provides a suited feature space for clustering purposes. The sensitivity obtained by using the evaluated clustering techniques is also compared with the well-known methods of Konishi-Fujii, weighted generalized differences, and wavelet entropy. The performance of the partitional clustering approach is evaluated using simulated dynamic speckle patterns and also experimental data.

Drop weight impact measurements of HE sensitivity: modified detection methods

International Nuclear Information System (INIS)

Preston, D N; Brown, G W; Tappan, B C; Oshwald, D M; Koby, J R; Schoonover, M L

2014-01-01

High explosives small-scale sensitivity testing has been a hallmark of safety screening since WWII. Sensitivity testing was once crude and simple; broom sticks were used to scrape explosives on the floor while experimenters would look, listen, and smell for signs of a reaction. Since then, a wide variety of testing apparatus have been developed to explore the effects of different stimuli on explosives. In concert with the development of the machines themselves, the reaction detection methods have also evolved. This paper's focus is on the Los Alamos National Laboratory's (LANL) drop weight impact machine and reaction detection methods. A critical evaluation of results is presented with cautionary examples of false positives that can occur with non-explosive materials.

An easily implemented static condensation method for structural sensitivity analysis

Science.gov (United States)

Gangadharan, S. N.; Haftka, R. T.; Nikolaidis, E.

1990-01-01

A black-box approach to static condensation for sensitivity analysis is presented with illustrative examples of a cube and a car structure. The sensitivity of the structural response with respect to joint stiffness parameter is calculated using the direct method, forward-difference, and central-difference schemes. The efficiency of the various methods for identifying joint stiffness parameters from measured static deflections of these structures is compared. The results indicate that the use of static condensation can reduce computation times significantly and the black-box approach is only slightly less efficient than the standard implementation of static condensation. The ease of implementation of the black-box approach recommends it for use with general-purpose finite element codes that do not have a built-in facility for static condensation.

Evaluation of phase sensitive detection method and Si avalanche photodiode for radiation thermometry

International Nuclear Information System (INIS)

Hobbs, M J; Tan, C H; Willmott, J R

2013-01-01

We report the evaluation of Si avalanche photodiodes (APDs) for use in radiation thermometry as an alternative to Si photodiodes. We compared their performance when operated under phase sensitive detection (PSD), where the signal is modulated, and direct detection (DD) methods. A Si APD was compared with a Si photodiode with reference black body temperatures of 275 to 600°C, in terms of the mean output voltage and signal-to-noise ratio (SNR), measured at different APD gain values. We found that using both PSD and DD methods, the high internal gain of the Si APD achieved a lower minimum detection temperature in order to satisfy a specific minimum output voltage of the detector-preamplifier combination employed. The use of PSD over DD for the Si APD allowed for improved performance of the thermometer, with a lower minimum measurable temperature, as well as improvement in the SNR. For instance we found that at 350°C, the Si APD biased at 150 V using PSD can provide ∼ 88 times enhancement in the system SNR over that of a Si photodiode using DD. A corresponding temperature error of ±0.05°C was achieved using the APD with PSD compared to an error of ±2.75°C measured using the Si photodiode with DD.

An in vitro method for detecting chemical sensitization using human reconstructed skin models and its applicability to cosmetic, pharmaceutical, and medical device safety testing.

Science.gov (United States)

McKim, James M; Keller, Donald J; Gorski, Joel R

2012-12-01

Chemical sensitization is a serious condition caused by small reactive molecules and is characterized by a delayed type hypersensitivity known as allergic contact dermatitis (ACD). Contact with these molecules via dermal exposure represent a significant concern for chemical manufacturers. Recent legislation in the EU has created the need to develop non-animal alternative methods for many routine safety studies including sensitization. Although most of the alternative research has focused on pure chemicals that possess reasonable solubility properties, it is important for any successful in vitro method to have the ability to test compounds with low aqueous solubility. This is especially true for the medical device industry where device extracts must be prepared in both polar and non-polar vehicles in order to evaluate chemical sensitization. The aim of this research was to demonstrate the functionality and applicability of the human reconstituted skin models (MatTek Epiderm(®) and SkinEthic RHE) as a test system for the evaluation of chemical sensitization and its potential use for medical device testing. In addition, the development of the human 3D skin model should allow the in vitro sensitization assay to be used for finished product testing in the personal care, cosmetics, and pharmaceutical industries. This approach combines solubility, chemical reactivity, cytotoxicity, and activation of the Nrf2/ARE expression pathway to identify and categorize chemical sensitizers. Known chemical sensitizers representing extreme/strong-, moderate-, weak-, and non-sensitizing potency categories were first evaluated in the skin models at six exposure concentrations ranging from 0.1 to 2500 µM for 24 h. The expression of eight Nrf2/ARE, one AhR/XRE and two Nrf1/MRE controlled gene were measured by qRT-PCR. The fold-induction at each exposure concentration was combined with reactivity and cytotoxicity data to determine the sensitization potential. The results demonstrated that

The rate of convergence in the method of alternating projections

Czech Academy of Sciences Publication Activity Database

Badea, C.; Grivaux, S.; Müller, Vladimír

2012-01-01

Roč. 23, č. 3 (2012), s. 413-434 ISSN 1061-0022 R&D Projects: GA ČR GA201/09/0473; GA AV ČR IAA100190903 Institutional support: RVO:67985840 Keywords : Friedrichs angle * method of alternating projections * arbitrarily slow convergence Subject RIV: BA - General Mathematics Impact factor: 0.460, year: 2012 http://www.ams.org/journals/spmj/2012-23-03/S1061-0022-2012-01202-1/home.html

Examination and Improvement of Accuracy of Three-Dimensional Elastic Crack Solutions Obtained Using Finite Element Alternating Method

International Nuclear Information System (INIS)

Park, Jai Hak; Nikishkov, G. P.

2010-01-01

An SGBEM (symmetric Galerkin boundary element method)-FEM alternating method has been proposed by Nikishkov, Park and Atluri. This method can be used to obtain mixed-mode stress intensity factors for planar and nonplanar three-dimensional cracks having an arbitrary shape. For field applications, however, it is necessary to verify the accuracy and consistency of this method. Therefore, in this study, we investigate the effects of several factors on the accuracy of the stress intensity factors obtained using the above mentioned alternating method. The obtained stress intensity factors are compared with the known values provided in handbooks, especially in the case of internal and external circumferential semi-elliptical surface cracks. The results show that the SGBEM-FEM alternating method yields accurate stress intensity factors for three-dimensional cracks, including internal and external circumferential surface cracks and that the method can be used as a robust crack analysis tool for solving field problems

Development of a localized probabilistic sensitivity method to determine random variable regional importance

International Nuclear Information System (INIS)

Millwater, Harry; Singh, Gulshan; Cortina, Miguel

2012-01-01

There are many methods to identify the important variable out of a set of random variables, i.e., “inter-variable” importance; however, to date there are no comparable methods to identify the “region” of importance within a random variable, i.e., “intra-variable” importance. Knowledge of the critical region of an input random variable (tail, near-tail, and central region) can provide valuable information towards characterizing, understanding, and improving a model through additional modeling or testing. As a result, an intra-variable probabilistic sensitivity method was developed and demonstrated for independent random variables that computes the partial derivative of a probabilistic response with respect to a localized perturbation in the CDF values of each random variable. These sensitivities are then normalized in absolute value with respect to the largest sensitivity within a distribution to indicate the region of importance. The methodology is implemented using the Score Function kernel-based method such that existing samples can be used to compute sensitivities for negligible cost. Numerical examples demonstrate the accuracy of the method through comparisons with finite difference and numerical integration quadrature estimates. - Highlights: ► Probabilistic sensitivity methodology. ► Determines the “region” of importance within random variables such as left tail, near tail, center, right tail, etc. ► Uses the Score Function approach to reuse the samples, hence, negligible cost. ► No restrictions on the random variable types or limit states.

76 FR 23323 - Meeting of the Scientific Advisory Committee on Alternative Toxicological Methods (SACATM)

Science.gov (United States)

2011-04-26

... the scientific validation and regulatory acceptance of toxicological and safety testing methods that... DEPARTMENT OF HEALTH AND HUMAN SERVICES Meeting of the Scientific Advisory Committee on Alternative Toxicological Methods (SACATM) AGENCY: National Toxicology Program (NTP), National Institute of...

Tunnel boring an alternative method in construction of spent fuel repositories

International Nuclear Information System (INIS)

Christersson, Jukka

1984-05-01

In projecting of the final disposal of nuclear waste in geological formations a great importance should be paid to the selection of the tunneling method. The environment of the chosen repository area should not be exposed to any but as minor disturbances as possible by the excavation method applied. This study approaches full face tunneling methods as an alternative to conventional drill-and-blast methods in the construction of spent fuel repository tunnels. According to experiences up till now it is obvious, that tunnelboring today is fully capable technically competing with conventional tunneling methods, even in the hardest granitic rocks. The most important advantages, it provides for the construction of repositories, are: The methods does not produce any damage in the surrounding rock. Possibility to use placement techniques, which do not require preparing of additive repository holes for the fuel elements. Saving in the use of expensive filling material. The fact, that tunnel boring in hard rock is an expensive alternative, is still valid. Constuction of straight lined tunnels in unfractured rocks by tunnel boring would cost about 30-40% more than by conventional methods. The lay out arrangement of bored tunnels still have a great influence on tunnel boring machine's economy. Due to this it would be round 40-70% more expensive method in the construction of spent fuel repositories. However intensive development w is being carried out to eliminate these limitations and to make machines more flexible. Future trends in tunnel boring look good at the moment. The number of sold units has been increasing and new applications have widen out during last ten years. Harder and more abrasive rocks can now be bored than ever before and the trend seems to continue. It also looks like the cost difference in the hardest rocks is firmly getting smaller and smaller all the time. (author)

Alternative method for quantification of alfa-amylase activity.

Science.gov (United States)

Farias, D F; Carvalho, A F U; Oliveira, C C; Sousa, N M; Rocha-Bezerrra, L C B; Ferreira, P M P; Lima, G P G; Hissa, D C

2010-05-01

A modification of the sensitive agar diffusion method was developed for macro-scale determination of alfa-amylase. The proposed modifications lower costs with the utilisation of starch as substrate and agar as supporting medium. Thus, a standard curve was built using alfa-amylase solution from Aspergillus oryzae, with concentrations ranging from 2.4 to 7,500 U.mL-1. Clear radial diffusion zones were measured after 4 hours of incubation at 20 A degrees C. A linear relationship between the logarithm of enzyme activities and the area of clear zones was obtained. The method was validated by testing alpha-amylase from barley at the concentrations of 2.4; 60; 300 and 1,500 U.mL-1. The proposed method turned out to be simpler, faster, less expensive and able to determine on a macro-scale alpha-amylase over a wide range (2.4 to 7,500 U.mL-1) in scientific investigation as well as in teaching laboratory activities.

Alternative method for quantification of alfa-amylase activity

Directory of Open Access Journals (Sweden)

DF. Farias

Full Text Available A modification of the sensitive agar diffusion method was developed for macro-scale determination of alfa-amylase. The proposed modifications lower costs with the utilisation of starch as substrate and agar as supporting medium. Thus, a standard curve was built using alfa-amylase solution from Aspergillus oryzae, with concentrations ranging from 2.4 to 7,500 U.mL-1. Clear radial diffusion zones were measured after 4 hours of incubation at 20 °C. A linear relationship between the logarithm of enzyme activities and the area of clear zones was obtained. The method was validated by testing α-amylase from barley at the concentrations of 2.4; 60; 300 and 1,500 U.mL-1. The proposed method turned out to be simpler, faster, less expensive and able to determine on a macro-scale α-amylase over a wide range (2.4 to 7,500 U.mL-1 in scientific investigation as well as in teaching laboratory activities.

Measurement of the resistivity of porous materials with an alternating air-flow method.

Science.gov (United States)

Dragonetti, Raffaele; Ianniello, Carmine; Romano, Rosario A

2011-02-01

Air-flow resistivity is a main parameter governing the acoustic behavior of porous materials for sound absorption. The international standard ISO 9053 specifies two different methods to measure the air-flow resistivity, namely a steady-state air-flow method and an alternating air-flow method. The latter is realized by the measurement of the sound pressure at 2 Hz in a small rigid volume closed partially by the test sample. This cavity is excited with a known volume-velocity sound source implemented often with a motor-driven piston oscillating with prescribed area and displacement magnitude. Measurements at 2 Hz require special instrumentation and care. The authors suggest an alternating air-flow method based on the ratio of sound pressures measured at frequencies higher than 2 Hz inside two cavities coupled through a conventional loudspeaker. The basic method showed that the imaginary part of the sound pressure ratio is useful for the evaluation of the air-flow resistance. Criteria are discussed about the choice of a frequency range suitable to perform simplified calculations with respect to the basic method. These criteria depend on the sample thickness, its nonacoustic parameters, and the measurement apparatus as well. The proposed measurement method was tested successfully with various types of acoustic materials.

Radiation sensitive devices and systems for detection of radioactive materials and related methods

Science.gov (United States)

Kotter, Dale K

2014-12-02

Radiation sensitive devices include a substrate comprising a radiation sensitive material and a plurality of resonance elements coupled to the substrate. Each resonance element is configured to resonate responsive to non-ionizing incident radiation. Systems for detecting radiation from a special nuclear material include a radiation sensitive device and a sensor located remotely from the radiation sensitive device and configured to measure an output signal from the radiation sensitive device. In such systems, the radiation sensitive device includes a radiation sensitive material and a plurality of resonance elements positioned on the radiation sensitive material. Methods for detecting a presence of a special nuclear material include positioning a radiation sensitive device in a location where special nuclear materials are to be detected and remotely interrogating the radiation sensitive device with a sensor.

An Alternative Method for Computing Unit Costs and Productivity Ratios. AIR 1984 Annual Forum Paper.

Science.gov (United States)

Winstead, Wayland H.; And Others

An alternative measure for evaluating the performance of academic departments was studied. A comparison was made with the traditional manner for computing unit costs and productivity ratios: prorating the salary and effort of each faculty member to each course level based on the personal mix of course taught. The alternative method used averaging…

Use of Biosensors as Alternatives to Current Regulatory Methods for Marine Biotoxins

Directory of Open Access Journals (Sweden)

Luis M. Botana

2009-11-01

Full Text Available Marine toxins are currently monitored by means of a bioassay that requires the use of many mice, which poses a technical and ethical problem in many countries. With the exception of domoic acid, there is a legal requirement for the presence of other toxins (yessotoxin, saxitoxin and analogs, okadaic acid and analogs, pectenotoxins and azaspiracids in seafood to be controlled by bioassay, but other toxins, such as palytoxin, cyclic imines, ciguatera and tetrodotoxin are potentially present in European food and there are no legal requirements or technical approaches available to identify their presence. The need for alternative methods to the bioassay is clearly important, and biosensors have become in recent years a feasible alternative to animal sacrifice. This review will discuss the advantages and disadvantages of using biosensors as alternatives to animal assays for marine toxins, with particular focus on surface plasmon resonance (SPR technology.

Computational Methods for Sensitivity and Uncertainty Analysis in Criticality Safety

International Nuclear Information System (INIS)

Broadhead, B.L.; Childs, R.L.; Rearden, B.T.

1999-01-01

Interest in the sensitivity methods that were developed and widely used in the 1970s (the FORSS methodology at ORNL among others) has increased recently as a result of potential use in the area of criticality safety data validation procedures to define computational bias, uncertainties and area(s) of applicability. Functional forms of the resulting sensitivity coefficients can be used as formal parameters in the determination of applicability of benchmark experiments to their corresponding industrial application areas. In order for these techniques to be generally useful to the criticality safety practitioner, the procedures governing their use had to be updated and simplified. This paper will describe the resulting sensitivity analysis tools that have been generated for potential use by the criticality safety community

Alternative methods for determination of composition and porosity in abradable materials

International Nuclear Information System (INIS)

Matejicek, Jiri; Kolman, Blahoslav; Dubsky, Jiri; Neufuss, Karel; Hopkins, Noel; Zwick, Jochen

2006-01-01

Materials properties and performance are governed by their composition and structure. These are commonly characterized using materialography and image analysis. However, in abradable materials, obtaining a reliable and representative sample (polished section) for this widespread technique is complicated by their abradable nature and heterogeneity. Therefore, alternative methods are also considered in this paper. They are namely X-ray diffraction and electron probe microanalysis to determine the composition, and mercury intrusion porosimetry, Archimedean porosimetry and helium pycnometry to determine the porosity. These methods, including materialography, were applied on representative abradable materials produced by plasma spraying; their results are compared and the advantages and drawbacks of each method are discussed

An Alternative to EPA Method 9 -- Field Validation of the Digital Opacity Compliance System (DOCS)

National Research Council Canada - National Science Library

Rasmussen, Steve L; Stone, Daniel A

2005-01-01

The Digital Opacity Compliance System (DOCS) software translates images from a commercial digital camera into visual plume opacity measurements, and is proposed as an alternate reporting method to EPA Method 9...

Invariant methods for an ensemble-based sensitivity analysis of a passive containment cooling system of an AP1000 nuclear power plant

International Nuclear Information System (INIS)

Di Maio, Francesco; Nicola, Giancarlo; Borgonovo, Emanuele; Zio, Enrico

2016-01-01

Sensitivity Analysis (SA) is performed to gain fundamental insights on a system behavior that is usually reproduced by a model and to identify the most relevant input variables whose variations affect the system model functional response. For the reliability analysis of passive safety systems of Nuclear Power Plants (NPPs), models are Best Estimate (BE) Thermal Hydraulic (TH) codes, that predict the system functional response in normal and accidental conditions and, in this paper, an ensemble of three alternative invariant SA methods is innovatively set up for a SA on the TH code input variables. The ensemble aggregates the input variables raking orders provided by Pearson correlation ratio, Delta method and Beta method. The capability of the ensemble is shown on a BE–TH code of the Passive Containment Cooling System (PCCS) of an Advanced Pressurized water reactor AP1000, during a Loss Of Coolant Accident (LOCA), whose output probability density function (pdf) is approximated by a Finite Mixture Model (FMM), on the basis of a limited number of simulations. - Highlights: • We perform the reliability analysis of a passive safety system of Nuclear Power Plant (NPP). • We use a Thermal Hydraulic (TH) code for predicting the NPP response to accidents. • We propose an ensemble of Invariant Methods for the sensitivity analysis of the TH code • The ensemble aggregates the rankings of Pearson correlation, Delta and Beta methods. • The approach is tested on a Passive Containment Cooling System of an AP1000 NPP.

The effect of alternative seismotectonic models on PSHA results - a sensitivity study for two sites in Israel

Science.gov (United States)

Avital, Matan; Kamai, Ronnie; Davis, Michael; Dor, Ory

2018-02-01

We present a full probabilistic seismic hazard analysis (PSHA) sensitivity analysis for two sites in southern Israel - one in the near field of a major fault system and one farther away. The PSHA analysis is conducted for alternative source representations, using alternative model parameters for the main seismic sources, such as slip rate and Mmax, among others. The analysis also considers the effect of the ground motion prediction equation (GMPE) on the hazard results. In this way, the two types of epistemic uncertainty - modelling uncertainty and parametric uncertainty - are treated and addressed. We quantify the uncertainty propagation by testing its influence on the final calculated hazard, such that the controlling knowledge gaps are identified and can be treated in future studies. We find that current practice in Israel, as represented by the current version of the building code, grossly underestimates the hazard, by approximately 40 % in short return periods (e.g. 10 % in 50 years) and by as much as 150 % in long return periods (e.g. 10E-5). The analysis shows that this underestimation is most probably due to a combination of factors, including source definitions as well as the GMPE used for analysis.

A sensitive new method of ex vivo platelet deposition

International Nuclear Information System (INIS)

Badimon, L.; Fuster, V.; Dewanjee, M.K.; Romero, J.C.

1982-01-01

In 1978, an in vivo quantitative method of platelet aggregation based on the increment of weight of a rabbit tendon when superfused with flowing blood (3 ml/min) derived from a carotid artery of a cat and reentering the contralateral jugular vein was reported. TO increase the sensitivity of the method, researches labeled platelets with indium-111 and reinjected them after two hours; then, with a gamma counter, researches quantitated the 111 In-labeled platelets deposited on the superfused rabbit tendon. Results of the radioactivity method and of the weight method were compared. Researchers found that the 111 In-labeling of platelets was more precise and reproducible method, rendering possible the use of a small amount of blood without need for reentry into the venous system

Greening Reversed-Phase Liquid Chromatography Methods Using Alternative Solvents for Pharmaceutical Analysis

Directory of Open Access Journals (Sweden)

Moussa Yabré

2018-05-01

Full Text Available The greening of analytical methods has gained increasing interest in the field of pharmaceutical analysis to reduce environmental impacts and improve the health safety of analysts. Reversed-phase high-performance liquid chromatography (RP-HPLC is the most widely used analytical technique involved in pharmaceutical drug development and manufacturing, such as the quality control of bulk drugs and pharmaceutical formulations, as well as the analysis of drugs in biological samples. However, RP-HPLC methods commonly use large amounts of organic solvents and generate high quantities of waste to be disposed, leading to some issues in terms of ecological impact and operator safety. In this context, greening HPLC methods is becoming highly desirable. One strategy to reduce the impact of hazardous solvents is to replace classically used organic solvents (i.e., acetonitrile and methanol with greener ones. So far, ethanol has been the most often used alternative organic solvent. Others strategies have followed, such as the use of totally aqueous mobile phases, micellar liquid chromatography, and ionic liquids. These approaches have been well developed, as they do not require equipment investments and are rather economical. This review describes and critically discusses the recent advances in greening RP-HPLC methods dedicated to pharmaceutical analysis based on the use of alternative solvents.

Workshop on acceleration of the validation and regulatory acceptance of alternative methods and implementation of testing strategies

DEFF Research Database (Denmark)

Piersma, A. H.; Burgdorf, T.; Louekari, K.

2018-01-01

concerning the regulatory acceptance and implementation of alternative test methods and testing strategies, with the aim to develop feasible solutions. Classical validation of alternative methods usually involves one to one comparison with the gold standard animal study. This approach suffers from...... the reductionist nature of an alternative test as compared to the animal study as well as from the animal study being considered as the gold standard. Modern approaches combine individual alternatives into testing strategies, for which integrated and defined approaches are emerging at OECD. Furthermore, progress......-focused hazard and risk assessment of chemicals requires an open mind towards stepping away from the animal study as the gold standard and defining human biologically based regulatory requirements for human hazard and risk assessment....

Computing eigenvalue sensitivity coefficients to nuclear data based on the CLUTCH method with RMC code

International Nuclear Information System (INIS)

Qiu, Yishu; She, Ding; Tang, Xiao; Wang, Kan; Liang, Jingang

2016-01-01

Highlights: • A new algorithm is proposed to reduce memory consumption for sensitivity analysis. • The fission matrix method is used to generate adjoint fission source distributions. • Sensitivity analysis is performed on a detailed 3D full-core benchmark with RMC. - Abstract: Recently, there is a need to develop advanced methods of computing eigenvalue sensitivity coefficients to nuclear data in the continuous-energy Monte Carlo codes. One of these methods is the iterated fission probability (IFP) method, which is adopted by most of Monte Carlo codes of having the capabilities of computing sensitivity coefficients, including the Reactor Monte Carlo code RMC. Though it is accurate theoretically, the IFP method faces the challenge of huge memory consumption. Therefore, it may sometimes produce poor sensitivity coefficients since the number of particles in each active cycle is not sufficient enough due to the limitation of computer memory capacity. In this work, two algorithms of the Contribution-Linked eigenvalue sensitivity/Uncertainty estimation via Tracklength importance CHaracterization (CLUTCH) method, namely, the collision-event-based algorithm (C-CLUTCH) which is also implemented in SCALE and the fission-event-based algorithm (F-CLUTCH) which is put forward in this work, are investigated and implemented in RMC to reduce memory requirements for computing eigenvalue sensitivity coefficients. While the C-CLUTCH algorithm requires to store concerning reaction rates of every collision, the F-CLUTCH algorithm only stores concerning reaction rates of every fission point. In addition, the fission matrix method is put forward to generate the adjoint fission source distribution for the CLUTCH method to compute sensitivity coefficients. These newly proposed approaches implemented in RMC code are verified by a SF96 lattice model and the MIT BEAVRS benchmark problem. The numerical results indicate the accuracy of the F-CLUTCH algorithm is the same as the C

Expert opinions on the acceptance of alternative methods in food safety evaluations

NARCIS (Netherlands)

Punt, Ans; Bouwmeester, Hans; Schiffelers, Marie Jeanne W.A.; Peijnenburg, Ad A.C.M.

2018-01-01

Inclusion of alternative methods that replace, reduce, or refine (3R) animal testing within regulatory safety evaluations of chemicals generally faces many hurdles. The goal of the current work is to i) collect responses from key stakeholders involved in food safety evaluations on what they consider

Analysis of alternative methods and price politic of icewine production

Directory of Open Access Journals (Sweden)

V. Ostapenko

2017-06-01

Full Text Available The artificial methods of must concentration were discussed in current study: the microwave vacuum dehydration, reverse osmosis and cryoextraction. The main factor of using of alternative ways is deficiently low temperatures in winter period that are necessary for freezing grapes on vine according to the classical technology. The benefits and disadvantages of using of non-classic processes to obtain sweet musts were shown. The physical, chemical and sensory characteristics of wine made from grapes previously frozen by alternative and natural ways were analyzed. Indicators influencing on price of icewines and dessert wines bottle including agricultural climatic, technological and marketing factors were determined.  Detailed indicators highlight specificity of used technology and represent consumer preferences. Producers of winemaking regions of Argentina, New Zealand, Israel, Ukraine and Australia adhere to provisions that are inconsistent with the standards of Canada and the European countries regarding the icewine output. These instruments determine the processing of grapes and parameters reflect on parameters of the finished product.

TiO_2 assisted photo-oxidation of wastewater prior to voltammetric determination of trace metals: Eco-friendly alternative to traditional digestion methods

International Nuclear Information System (INIS)

Lejbt, Beata; Ospina-Alvarez, Natalia; Miecznikowski, Krzysztof; Krasnodębska-Ostręga, Beata

2016-01-01

Highlights: • Cheap and eco-friendly method using anatase-assisted photodecomposition to pre-treat wastewater samples prior to trace metal analysis. • Addition of polyvinylidene fluoride did not affect the efficiency of organic matter decomposition. • TiO_2 assisted photo-oxidation procedure is equally effective than ICP MS determination after UV assisted digestion with H_2O_2 addition. - Abstract: Voltammetry is a sensitive method for metal determination and one alternative to ICP MS, but its limitation is the influence of the organic matrix on the measurements. To avoid those interferences, wet digestion with H_2O_2 accelerated with UV irradiation is applied and evaporation of excess of reagents is required. In this study, photolytic oxidation in quartz tubes with anatase was carried out, using as object of study wastewater samples with high amount of organic matter. Cadmium and lead determination was carried out in order to test metal recoveries. Lead recoveries reached c.a 85% for UV digestion with hydrogen peroxide, 98% for digestion with anatase immobilized with polyvinylidene fluoride (N-metylo-2-pirolidon) and c.a 103% for digestion with immobilized anatase (anatase in gum). The results obtained showed the usefulness of TiO_2 layer as an oxidation medium. An easy, cheap and eco-friendly digestion method of surfactants without any reagent has been developed, with equal sensitivity but and the same detection limit of traditional digestion methods.

Investigation of modern methods of probalistic sensitivity analysis of final repository performance assessment models (MOSEL)

International Nuclear Information System (INIS)

Spiessl, Sabine; Becker, Dirk-Alexander

2017-06-01

Sensitivity analysis is a mathematical means for analysing the sensitivities of a computational model to variations of its input parameters. Thus, it is a tool for managing parameter uncertainties. It is often performed probabilistically as global sensitivity analysis, running the model a large number of times with different parameter value combinations. Going along with the increase of computer capabilities, global sensitivity analysis has been a field of mathematical research for some decades. In the field of final repository modelling, probabilistic analysis is regarded a key element of a modern safety case. An appropriate uncertainty and sensitivity analysis can help identify parameters that need further dedicated research to reduce the overall uncertainty, generally leads to better system understanding and can thus contribute to building confidence in the models. The purpose of the project described here was to systematically investigate different numerical and graphical techniques of sensitivity analysis with typical repository models, which produce a distinctly right-skewed and tailed output distribution and can exhibit a highly nonlinear, non-monotonic or even non-continuous behaviour. For the investigations presented here, three test models were defined that describe generic, but typical repository systems. A number of numerical and graphical sensitivity analysis methods were selected for investigation and, in part, modified or adapted. Different sampling methods were applied to produce various parameter samples of different sizes and many individual runs with the test models were performed. The results were evaluated with the different methods of sensitivity analysis. On this basis the methods were compared and assessed. This report gives an overview of the background and the applied methods. The results obtained for three typical test models are presented and explained; conclusions in view of practical applications are drawn. At the end, a recommendation

Investigation of modern methods of probalistic sensitivity analysis of final repository performance assessment models (MOSEL)

Energy Technology Data Exchange (ETDEWEB)

Spiessl, Sabine; Becker, Dirk-Alexander

2017-06-15

Sensitivity analysis is a mathematical means for analysing the sensitivities of a computational model to variations of its input parameters. Thus, it is a tool for managing parameter uncertainties. It is often performed probabilistically as global sensitivity analysis, running the model a large number of times with different parameter value combinations. Going along with the increase of computer capabilities, global sensitivity analysis has been a field of mathematical research for some decades. In the field of final repository modelling, probabilistic analysis is regarded a key element of a modern safety case. An appropriate uncertainty and sensitivity analysis can help identify parameters that need further dedicated research to reduce the overall uncertainty, generally leads to better system understanding and can thus contribute to building confidence in the models. The purpose of the project described here was to systematically investigate different numerical and graphical techniques of sensitivity analysis with typical repository models, which produce a distinctly right-skewed and tailed output distribution and can exhibit a highly nonlinear, non-monotonic or even non-continuous behaviour. For the investigations presented here, three test models were defined that describe generic, but typical repository systems. A number of numerical and graphical sensitivity analysis methods were selected for investigation and, in part, modified or adapted. Different sampling methods were applied to produce various parameter samples of different sizes and many individual runs with the test models were performed. The results were evaluated with the different methods of sensitivity analysis. On this basis the methods were compared and assessed. This report gives an overview of the background and the applied methods. The results obtained for three typical test models are presented and explained; conclusions in view of practical applications are drawn. At the end, a recommendation

Survey of sampling-based methods for uncertainty and sensitivity analysis

International Nuclear Information System (INIS)

Helton, J.C.; Johnson, J.D.; Sallaberry, C.J.; Storlie, C.B.

2006-01-01

Sampling-based methods for uncertainty and sensitivity analysis are reviewed. The following topics are considered: (i) definition of probability distributions to characterize epistemic uncertainty in analysis inputs (ii) generation of samples from uncertain analysis inputs (iii) propagation of sampled inputs through an analysis (iv) presentation of uncertainty analysis results, and (v) determination of sensitivity analysis results. Special attention is given to the determination of sensitivity analysis results, with brief descriptions and illustrations given for the following procedures/techniques: examination of scatterplots, correlation analysis, regression analysis, partial correlation analysis, rank transformations, statistical tests for patterns based on gridding, entropy tests for patterns based on gridding, nonparametric regression analysis, squared rank differences/rank correlation coefficient test, two-dimensional Kolmogorov-Smirnov test, tests for patterns based on distance measures, top down coefficient of concordance, and variance decomposition

Survey of sampling-based methods for uncertainty and sensitivity analysis.

Energy Technology Data Exchange (ETDEWEB)

Johnson, Jay Dean; Helton, Jon Craig; Sallaberry, Cedric J. PhD. (.; .); Storlie, Curt B. (Colorado State University, Fort Collins, CO)

2006-06-01

Sampling-based methods for uncertainty and sensitivity analysis are reviewed. The following topics are considered: (1) Definition of probability distributions to characterize epistemic uncertainty in analysis inputs, (2) Generation of samples from uncertain analysis inputs, (3) Propagation of sampled inputs through an analysis, (4) Presentation of uncertainty analysis results, and (5) Determination of sensitivity analysis results. Special attention is given to the determination of sensitivity analysis results, with brief descriptions and illustrations given for the following procedures/techniques: examination of scatterplots, correlation analysis, regression analysis, partial correlation analysis, rank transformations, statistical tests for patterns based on gridding, entropy tests for patterns based on gridding, nonparametric regression analysis, squared rank differences/rank correlation coefficient test, two dimensional Kolmogorov-Smirnov test, tests for patterns based on distance measures, top down coefficient of concordance, and variance decomposition.

Method for exploiting bias in factor analysis using constrained alternating least squares algorithms

Science.gov (United States)

Keenan, Michael R.

2008-12-30

Bias plays an important role in factor analysis and is often implicitly made use of, for example, to constrain solutions to factors that conform to physical reality. However, when components are collinear, a large range of solutions may exist that satisfy the basic constraints and fit the data equally well. In such cases, the introduction of mathematical bias through the application of constraints may select solutions that are less than optimal. The biased alternating least squares algorithm of the present invention can offset mathematical bias introduced by constraints in the standard alternating least squares analysis to achieve factor solutions that are most consistent with physical reality. In addition, these methods can be used to explicitly exploit bias to provide alternative views and provide additional insights into spectral data sets.

ALTERNATIVE FIELD METHODS TO TREAT MERCURY IN SOIL

International Nuclear Information System (INIS)

Stine, Ernie F.

2002-01-01

The Department of Energy (DOE) currently has mercury (Hg) contaminated materials and soils at the various sites. Figure 1-1 (from http://www.ct.ornl.gov/stcg.hg/) shows the estimated distribution of mercury contaminated waste at the various DOE sites. Oak Ridge and Idaho sites have the largest deposits of contaminated materials. The majorities of these contaminated materials are soils, sludges, debris, and waste waters. This project concerns treatment of mercury contaminated soils. The technology is applicable to many DOE sites, in-particular, the Y-12 National Security Complex in Oak Ridge Tennessee and Idaho National Engineering and Environmental Laboratory (INEEL). These sites have the majority of the soils and sediments contaminated with mercury. The soils may also be contaminated with other hazardous metals and radionuclides. At the Y12 plant, the baseline treatment method for mercury contaminated soil is low temperature thermal desorption (LTTD), followed by on-site landfill disposal. LTTD is relatively expensive (estimated cost of treatment which exclude disposal cost for the collect mercury is greater than $740/per cubic yard [cy] at Y-12), does not treat any of the metal or radionuclides. DOE is seeking a less costly alternative to the baseline technology. As described in the solicitation (DE-RA-01NT41030), this project initially focused on evaluating cost-effective in-situ alternatives to stabilize or remove the mercury (Hg) contamination from high-clay content soil. It was believed that ex-situ treatment of soil contaminated with significant quantities of free-liquid mercury might pose challenges during excavation and handling. Such challenges may include controlling potential mercury vapors and containing liquid mercury beads. As described below, the focus of this project was expanded to include consideration of ex-situ treatment after award of the contract to International Technology Corporation (IT). After award of the contract, IT became part of Shaw

ALTERNATIVE FIELD METHODS TO TREAT MERCURY IN SOIL

Energy Technology Data Exchange (ETDEWEB)

Ernie F. Stine

2002-08-14

The Department of Energy (DOE) currently has mercury (Hg) contaminated materials and soils at the various sites. Figure 1-1 (from http://www.ct.ornl.gov/stcg.hg/) shows the estimated distribution of mercury contaminated waste at the various DOE sites. Oak Ridge and Idaho sites have the largest deposits of contaminated materials. The majorities of these contaminated materials are soils, sludges, debris, and waste waters. This project concerns treatment of mercury contaminated soils. The technology is applicable to many DOE sites, in-particular, the Y-12 National Security Complex in Oak Ridge Tennessee and Idaho National Engineering and Environmental Laboratory (INEEL). These sites have the majority of the soils and sediments contaminated with mercury. The soils may also be contaminated with other hazardous metals and radionuclides. At the Y12 plant, the baseline treatment method for mercury contaminated soil is low temperature thermal desorption (LTTD), followed by on-site landfill disposal. LTTD is relatively expensive (estimated cost of treatment which exclude disposal cost for the collect mercury is greater than $740/per cubic yard [cy] at Y-12), does not treat any of the metal or radionuclides. DOE is seeking a less costly alternative to the baseline technology. As described in the solicitation (DE-RA-01NT41030), this project initially focused on evaluating cost-effective in-situ alternatives to stabilize or remove the mercury (Hg) contamination from high-clay content soil. It was believed that ex-situ treatment of soil contaminated with significant quantities of free-liquid mercury might pose challenges during excavation and handling. Such challenges may include controlling potential mercury vapors and containing liquid mercury beads. As described below, the focus of this project was expanded to include consideration of ex-situ treatment after award of the contract to International Technology Corporation (IT). After award of the contract, IT became part of Shaw

A simple and sensitive method for determination of Norfloxacin in pharmaceutical preparations

Directory of Open Access Journals (Sweden)

Zhuo Ye

2015-06-01

Full Text Available In this approach, a new voltammetric method for determination of norfloxacin was proposed with high sensitivity and wider detection linear range. The used voltammetric sensor was fabricated simply by coating a layer of graphene oxide (GO and Nafion composited film on glassy carbon electrode. The advantage of proposed method was sensitive electrochemical response for norfloxacin, which was attributed to the excellent electrical conductivity of GO and the accumulating function of Nafion under optimum experimental conditions, the present method revealed a good linear response for determination of norfloxacin in the range of 1×10-8mol/L-7×10-6 mol/L with a detection limit of 5×10-9 mol/L. The proposed method was successfully applied in the determination of norfloxacin in capsules with satisfactory results.

Alternate method of source preparation for alpha spectrometry: No electrodeposition, no hydrofluoric acid

International Nuclear Information System (INIS)

Kurosaki, Hiromu; Mueller, Rebecca J.; Lambert, Susan B.; Rao, Govind R.

2016-01-01

An alternate method of preparing actinide alpha counting sources was developed in place of electrodeposition or lanthanide fluoride micro-precipitation. The method uses lanthanide hydroxide micro-precipitation to avoid the use of hazardous hydrofluoric acid. Lastly, it provides a quicker, simpler, and safer way of preparing actinide alpha counting sources in routine, production-type laboratories that process many samples daily.

Alternate method of source preparation for alpha spectrometry: no electrodeposition, no hydrofluoric acid

International Nuclear Information System (INIS)

Hiromu Kurosaki; Lambert, S.B.; Rao, G.R.; Mueller, R.J.

2017-01-01

An alternate method of preparing actinide alpha counting sources was developed in place of electrodeposition or lanthanide fluoride micro-precipitation. The method uses lanthanide hydroxide micro-precipitation to avoid the use of hazardous hydrofluoric acid. It provides a quicker, simpler, and safer way of preparing actinide alpha counting sources in routine, production-type laboratories that process many samples daily. (author)

The implicit restarted Arnoldi method, an efficient alternative to solve the neutron diffusion equation

Energy Technology Data Exchange (ETDEWEB)

Verdu, G.; Miro, R. [Departamento de Ingenieria Quimica y Nuclear, Universidad Politecnica de Valencia, Valencia (Spain); Ginestar, D. [Departamento de Matematica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain); Vidal, V. [Departamento de Sistemas Informaticos y Computacion, Universidad Politecnica de Valencia, Valencia (Spain)

1999-05-01

To calculate the neutronic steady state of a nuclear power reactor core and its subcritical modes, it is necessary to solve a partial eigenvalue problem. In this paper, an implicit restarted Arnoldi method is presented as an advantageous alternative to classical methods as the Power Iteration method and the Subspace Iteration method. The efficiency of these methods, has been compared calculating the dominant Lambda modes of several configurations of the Three Mile Island reactor core.

Blind compressed sensing image reconstruction based on alternating direction method

Science.gov (United States)

Liu, Qinan; Guo, Shuxu

2018-04-01

In order to solve the problem of how to reconstruct the original image under the condition of unknown sparse basis, this paper proposes an image reconstruction method based on blind compressed sensing model. In this model, the image signal is regarded as the product of a sparse coefficient matrix and a dictionary matrix. Based on the existing blind compressed sensing theory, the optimal solution is solved by the alternative minimization method. The proposed method solves the problem that the sparse basis in compressed sensing is difficult to represent, which restrains the noise and improves the quality of reconstructed image. This method ensures that the blind compressed sensing theory has a unique solution and can recover the reconstructed original image signal from a complex environment with a stronger self-adaptability. The experimental results show that the image reconstruction algorithm based on blind compressed sensing proposed in this paper can recover high quality image signals under the condition of under-sampling.

Alternative (non-animal) methods for cosmetics testing: current status and future prospects-2010.

Science.gov (United States)

Adler, Sarah; Basketter, David; Creton, Stuart; Pelkonen, Olavi; van Benthem, Jan; Zuang, Valérie; Andersen, Klaus Ejner; Angers-Loustau, Alexandre; Aptula, Aynur; Bal-Price, Anna; Benfenati, Emilio; Bernauer, Ulrike; Bessems, Jos; Bois, Frederic Y; Boobis, Alan; Brandon, Esther; Bremer, Susanne; Broschard, Thomas; Casati, Silvia; Coecke, Sandra; Corvi, Raffaella; Cronin, Mark; Daston, George; Dekant, Wolfgang; Felter, Susan; Grignard, Elise; Gundert-Remy, Ursula; Heinonen, Tuula; Kimber, Ian; Kleinjans, Jos; Komulainen, Hannu; Kreiling, Reinhard; Kreysa, Joachim; Leite, Sofia Batista; Loizou, George; Maxwell, Gavin; Mazzatorta, Paolo; Munn, Sharon; Pfuhler, Stefan; Phrakonkham, Pascal; Piersma, Aldert; Poth, Albrecht; Prieto, Pilar; Repetto, Guillermo; Rogiers, Vera; Schoeters, Greet; Schwarz, Michael; Serafimova, Rositsa; Tähti, Hanna; Testai, Emanuela; van Delft, Joost; van Loveren, Henk; Vinken, Mathieu; Worth, Andrew; Zaldivar, José-Manuel

2011-05-01

The 7th amendment to the EU Cosmetics Directive prohibits to put animal-tested cosmetics on the market in Europe after 2013. In that context, the European Commission invited stakeholder bodies (industry, non-governmental organisations, EU Member States, and the Commission's Scientific Committee on Consumer Safety) to identify scientific experts in five toxicological areas, i.e. toxicokinetics, repeated dose toxicity, carcinogenicity, skin sensitisation, and reproductive toxicity for which the Directive foresees that the 2013 deadline could be further extended in case alternative and validated methods would not be available in time. The selected experts were asked to analyse the status and prospects of alternative methods and to provide a scientifically sound estimate of the time necessary to achieve full replacement of animal testing. In summary, the experts confirmed that it will take at least another 7-9 years for the replacement of the current in vivo animal tests used for the safety assessment of cosmetic ingredients for skin sensitisation. However, the experts were also of the opinion that alternative methods may be able to give hazard information, i.e. to differentiate between sensitisers and non-sensitisers, ahead of 2017. This would, however, not provide the complete picture of what is a safe exposure because the relative potency of a sensitiser would not be known. For toxicokinetics, the timeframe was 5-7 years to develop the models still lacking to predict lung absorption and renal/biliary excretion, and even longer to integrate the methods to fully replace the animal toxicokinetic models. For the systemic toxicological endpoints of repeated dose toxicity, carcinogenicity and reproductive toxicity, the time horizon for full replacement could not be estimated.

Sensitivity analysis techniques applied to a system of hyperbolic conservation laws

International Nuclear Information System (INIS)

Weirs, V. Gregory; Kamm, James R.; Swiler, Laura P.; Tarantola, Stefano; Ratto, Marco; Adams, Brian M.; Rider, William J.; Eldred, Michael S.

2012-01-01

Sensitivity analysis is comprised of techniques to quantify the effects of the input variables on a set of outputs. In particular, sensitivity indices can be used to infer which input parameters most significantly affect the results of a computational model. With continually increasing computing power, sensitivity analysis has become an important technique by which to understand the behavior of large-scale computer simulations. Many sensitivity analysis methods rely on sampling from distributions of the inputs. Such sampling-based methods can be computationally expensive, requiring many evaluations of the simulation; in this case, the Sobol' method provides an easy and accurate way to compute variance-based measures, provided a sufficient number of model evaluations are available. As an alternative, meta-modeling approaches have been devised to approximate the response surface and estimate various measures of sensitivity. In this work, we consider a variety of sensitivity analysis methods, including different sampling strategies, different meta-models, and different ways of evaluating variance-based sensitivity indices. The problem we consider is the 1-D Riemann problem. By a careful choice of inputs, discontinuous solutions are obtained, leading to discontinuous response surfaces; such surfaces can be particularly problematic for meta-modeling approaches. The goal of this study is to compare the estimated sensitivity indices with exact values and to evaluate the convergence of these estimates with increasing samples sizes and under an increasing number of meta-model evaluations. - Highlights: ► Sensitivity analysis techniques for a model shock physics problem are compared. ► The model problem and the sensitivity analysis problem have exact solutions. ► Subtle details of the method for computing sensitivity indices can affect the results.

Aquifer sensitivity to pesticide leaching: Testing a soils and hydrogeologic index method

Science.gov (United States)

Mehnert, E.; Keefer, D.A.; Dey, W.S.; Wehrmann, H.A.; Wilson, S.D.; Ray, C.

2005-01-01

For years, researchers have sought index and other methods to predict aquifer sensitivity and vulnerability to nonpoint pesticide contamination. In 1995, an index method and map were developed to define aquifer sensitivity to pesticide leaching based on a combination of soil and hydrogeologic factors. The soil factor incorporated three soil properties: hydraulic conductivity, amount of organic matter within individual soil layers, and drainage class. These properties were obtained from a digital soil association map. The hydrogeologic factor was depth to uppermost aquifer material. To test this index method, a shallow ground water monitoring well network was designed, installed, and sampled in Illinois. The monitoring wells had a median depth of 7.6 m and were located adjacent to corn and soybean fields where the only known sources of pesticides were those used in normal agricultural production. From September 1998 through February 2001, 159 monitoring wells were sampled for 14 pesticides but no pesticide metabolites. Samples were collected and analyzed to assess the distribution of pesticide occurrence across three units of aquifer sensitivity. Pesticides were detected in 18% of all samples and nearly uniformly from samples from the three units of aquifer sensitivity. The new index method did not predict pesticide occurrence because occurrence was not dependent on the combined soil and hydrogeologic factors. However, pesticide occurrence was dependent on the tested hydrogeologic factor and was three times higher in areas where the depth to the uppermost aquifer was <6 m than in areas where the depth to the uppermost aquifer was 6 to <15 m. Copyright ?? 2005 National Ground Water Association.

Highly sensitive high resolution Raman spectroscopy using resonant ionization methods

International Nuclear Information System (INIS)

Owyoung, A.; Esherick, P.

1984-05-01

In recent years, the introduction of stimulated Raman methods has offered orders of magnitude improvement in spectral resolving power for gas phase Raman studies. Nevertheless, the inherent weakness of the Raman process suggests the need for significantly more sensitive techniques in Raman spectroscopy. In this we describe a new approach to this problem. Our new technique, which we call ionization-detected stimulated Raman spectroscopy (IDSRS), combines high-resolution SRS with highly-sensitive resonant laser ionization to achieve an increase in sensitivity of over three orders of magnitude. The excitation/detection process involves three sequential steps: (1) population of a vibrationally excited state via stimulated Raman pumping; (2) selective ionization of the vibrationally excited molecule with a tunable uv source; and (3) collection of the ionized species at biased electrodes where they are detected as current in an external circuit

Estimation of the sensitivity of various environmental sampling methods for detection of Salmonella in duck flocks.

Science.gov (United States)

Arnold, Mark E; Mueller-Doblies, Doris; Gosling, Rebecca J; Martelli, Francesca; Davies, Robert H

2015-01-01

Reports of Salmonella in ducks in the UK currently rely upon voluntary submissions from the industry, and as there is no harmonized statutory monitoring and control programme, it is difficult to compare data from different years in order to evaluate any trends in Salmonella prevalence in relation to sampling methodology. Therefore, the aim of this project was to assess the sensitivity of a selection of environmental sampling methods, including the sampling of faeces, dust and water troughs or bowls for the detection of Salmonella in duck flocks, and a range of sampling methods were applied to 67 duck flocks. Bayesian methods in the absence of a gold standard were used to provide estimates of the sensitivity of each of the sampling methods relative to the within-flock prevalence. There was a large influence of the within-flock prevalence on the sensitivity of all sample types, with sensitivity reducing as the within-flock prevalence reduced. Boot swabs (individual and pool of four), swabs of faecally contaminated areas and whole house hand-held fabric swabs showed the overall highest sensitivity for low-prevalence flocks and are recommended for use to detect Salmonella in duck flocks. The sample type with the highest proportion positive was a pool of four hair nets used as boot swabs, but this was not the most sensitive sample for low-prevalence flocks. All the environmental sampling types (faeces swabs, litter pinches, drag swabs, water trough samples and dust) had higher sensitivity than individual faeces sampling. None of the methods consistently identified all the positive flocks, and at least 10 samples would be required for even the most sensitive method (pool of four boot swabs) to detect a 5% prevalence. The sampling of dust had a low sensitivity and is not recommended for ducks.

Alternative test method to assess the energy performance of frost-free refrigerating appliances

International Nuclear Information System (INIS)

Hermes, Christian J.L.; Melo, Cláudio; Knabben, Fernando T.

2013-01-01

This paper outlines an alternative test method to evaluate the energy consumption of frost-free refrigerators and freezers for residential applications. While the standardized methods require the refrigerating appliance to be kept running according to its onboard control system, which usually drives the refrigerator through an on–off cycling pattern, the proposed approach assesses the refrigerator energy performance in the steady-state regime, being therefore much faster and more reliable. In this procedure, the cooling capacity is matched to the cooling loads by PID-controlled electrical heaters installed within the refrigerated compartments, so that the compartment temperatures are kept at the desired standardized levels. Comparisons between the experimental results obtained using the steady-state energy test and the standardized procedures showed that the former follows closely the trends observed for the latter. - Highlights: ► An alternative test method to assess the energy consumption of refrigerators is proposed. ► PID-controlled electrical heaters were installed within the compartments. ► Steady-state and ISO energy tests were performed and compared. ► Both proposed and standardized test procedures showed similar trends.

ALTERNATIVE METHOD FOR ON SITE EVALUATION OF THERMAL TRANSMITTANCE

Directory of Open Access Journals (Sweden)

Aleksandar Janković

2017-08-01

Full Text Available Thermal transmittance or U-value is an indicator of the building envelope thermal properties and a key parameter for evaluation of heat losses through the building elements due to heat transmission. It can be determined by calculation based on thermal characteristics of the building element layers. However, this value does not take into account the effects of irregularities and degradation of certain elements of the envelope caused by aging, which may lead to errors in calculation of the heat losses. An effective and simple method for determination of thermal transmittance is in situ measurement, which is governed by the ISO 9869-1:2014 that defines heat flow meter method. This relatively expensive method leaves marks and damages surface of the building element. Furthermore, the final result is not always reliable, in particular when the building element is light or when the weather conditions are not suitable. In order to avoid the above mentioned problems and to estimate the real thermal transmittance value an alternative experimental method, here referred as the natural convection and radiation method, is proposed in this paper. For determination of thermal transmittance, this method requires only temperatures of inside and outside air, as well as the inner wall surface temperature. A detailed statistical analysis, performed by the software package SPSS ver. 20, shows several more advantages of this method comparing to the standard heat flow meter one, besides economic and non-destructive benefits.

Evaluation of Alternative Euthanasia Methods of Neonatal Chickens

Directory of Open Access Journals (Sweden)

Shailesh Gurung

2018-03-01

Full Text Available Hatched male layer chicks are currently euthanized by maceration in the United States. Public concerns on the use of maceration have led to the search for alternative methods. We hypothesized that gas inhalation and low atmospheric pressure stunning (LAPS are viable and humane alternatives to instantaneous mechanical destruction. The objective of this study was to evaluate the physiological and behavioral responses of recently hatched male layer chicks when subjected to carbon dioxide, nitrogen inhalation, or LAPS. The study consisted of seven treatments: breathing air (NEG, 25% carbon dioxide (CO2, 50% CO2, 75% CO2, 90% CO2, 100% nitrogen (N2, or LAPS. Ten day-of-hatch, male layer chicks were randomly assigned to each treatment, and each treatment was replicated on ten different days. A custom-made vacuum system was used to reduce air pressure inside the chamber from 100.12 kPa to 15.3 kPa for the LAPS treatment. Serum corticosterone and serotonin levels were measured using commercially available competitive enzyme linked immunosorbent assay (ELISA. Latencies to loss of posture and motionlessness were determined from video recordings. The 25% and 50% CO2 treatments were discontinued after the first replication, as the majority of the chicks recovered. The chicks in the negative (NEG group had significantly higher levels of corticosterone than the other four euthanasia treatments. On the other hand, the serotonin levels of chicks in the NEG group was significantly lower when compared to the other four euthanasia treatments. The latencies to loss of posture and motionlessness of chicks exposed to 75% and 90% CO2 were significantly shorter than those in the LAPS and N2 inhalation treatments. These data suggest that the stress responses of chicks to the CO2, N2, and LAPS treatments do not differ among each other. However, the CO2 inhalation method was faster in inducing loss of posture and motionlessness in chicks than the LAPS and N2 inhalation

Evaluation of Alternative Euthanasia Methods of Neonatal Chickens.

Science.gov (United States)

Gurung, Shailesh; White, Dima; Archer, Gregory; Zhao, Dan; Farnell, Yuhua; Byrd, J Allen; Peebles, E David; Farnell, Morgan

2018-03-09

Hatched male layer chicks are currently euthanized by maceration in the United States. Public concerns on the use of maceration have led to the search for alternative methods. We hypothesized that gas inhalation and low atmospheric pressure stunning (LAPS) are viable and humane alternatives to instantaneous mechanical destruction. The objective of this study was to evaluate the physiological and behavioral responses of recently hatched male layer chicks when subjected to carbon dioxide, nitrogen inhalation, or LAPS. The study consisted of seven treatments: breathing air (NEG), 25% carbon dioxide (CO₂), 50% CO₂, 75% CO₂, 90% CO₂, 100% nitrogen (N₂), or LAPS. Ten day-of-hatch, male layer chicks were randomly assigned to each treatment, and each treatment was replicated on ten different days. A custom-made vacuum system was used to reduce air pressure inside the chamber from 100.12 kPa to 15.3 kPa for the LAPS treatment. Serum corticosterone and serotonin levels were measured using commercially available competitive enzyme linked immunosorbent assay (ELISA). Latencies to loss of posture and motionlessness were determined from video recordings. The 25% and 50% CO₂ treatments were discontinued after the first replication, as the majority of the chicks recovered. The chicks in the negative (NEG) group had significantly higher levels of corticosterone than the other four euthanasia treatments. On the other hand, the serotonin levels of chicks in the NEG group was significantly lower when compared to the other four euthanasia treatments. The latencies to loss of posture and motionlessness of chicks exposed to 75% and 90% CO₂ were significantly shorter than those in the LAPS and N₂ inhalation treatments. These data suggest that the stress responses of chicks to the CO₂, N₂, and LAPS treatments do not differ among each other. However, the CO₂ inhalation method was faster in inducing loss of posture and motionlessness in chicks than the LAPS and N�

An alternative method for the measurement of the mechanical impulse of a vertically directed blast

CSIR Research Space (South Africa)

Turner, GR

2008-01-01

Full Text Available An alternative method for the measurement of the total mechanical impulse of a vertically directed blast due to an explosive charge is presented. The method differs from apparatus that employ a vertically displaced mass (similar in principle...

Sensitivity Analysis for Steady State Groundwater Flow Using Adjoint Operators

Science.gov (United States)

Sykes, J. F.; Wilson, J. L.; Andrews, R. W.

1985-03-01

Adjoint sensitivity theory is currently being considered as a potential method for calculating the sensitivity of nuclear waste repository performance measures to the parameters of the system. For groundwater flow systems, performance measures of interest include piezometric heads in the vicinity of a waste site, velocities or travel time in aquifers, and mass discharge to biosphere points. The parameters include recharge-discharge rates, prescribed boundary heads or fluxes, formation thicknesses, and hydraulic conductivities. The derivative of a performance measure with respect to the system parameters is usually taken as a measure of sensitivity. To calculate sensitivities, adjoint sensitivity equations are formulated from the equations describing the primary problem. The solution of the primary problem and the adjoint sensitivity problem enables the determination of all of the required derivatives and hence related sensitivity coefficients. In this study, adjoint sensitivity theory is developed for equations of two-dimensional steady state flow in a confined aquifer. Both the primary flow equation and the adjoint sensitivity equation are solved using the Galerkin finite element method. The developed computer code is used to investigate the regional flow parameters of the Leadville Formation of the Paradox Basin in Utah. The results illustrate the sensitivity of calculated local heads to the boundary conditions. Alternatively, local velocity related performance measures are more sensitive to hydraulic conductivities.

Linearized Alternating Direction Method of Multipliers for Constrained Nonconvex Regularized Optimization

Science.gov (United States)

2016-11-22

structure of the graph, we replace the ℓ1- norm by the nonconvex Capped -ℓ1 norm , and obtain the Generalized Capped -ℓ1 regularized logistic regression...X. M. Yuan. Linearized augmented lagrangian and alternating direction methods for nuclear norm minimization. Mathematics of Computation, 82(281):301...better approximations of ℓ0- norm theoretically and computationally beyond ℓ1- norm , for example, the compressive sensing (Xiao et al., 2011). The

Transfer of a two-tiered keratinocyte assay: IL-18 production by NCTC2544 to determine the skin sensitizing capacity and epidermal equivalent assay to determine sensitizer potency

DEFF Research Database (Denmark)

Teunis, Marc; Corsini, Emanuela; Smits, Mieke

2013-01-01

. The two tiered approach may offer an unique opportunity to provide an alternative method to the Local Lymph Node Assay (LLNA). These assays are both based on the use of human keratinocytes, which have been shown over the last two decades, to play a key role in all phases of skin sensitization....

TiO{sub 2} assisted photo-oxidation of wastewater prior to voltammetric determination of trace metals: Eco-friendly alternative to traditional digestion methods

Energy Technology Data Exchange (ETDEWEB)

Lejbt, Beata; Ospina-Alvarez, Natalia; Miecznikowski, Krzysztof, E-mail: kmiecz@chem.uw.edu.pl; Krasnodębska-Ostręga, Beata, E-mail: bekras@chem.uw.edu.pl

2016-12-01

Highlights: • Cheap and eco-friendly method using anatase-assisted photodecomposition to pre-treat wastewater samples prior to trace metal analysis. • Addition of polyvinylidene fluoride did not affect the efficiency of organic matter decomposition. • TiO{sub 2} assisted photo-oxidation procedure is equally effective than ICP MS determination after UV assisted digestion with H{sub 2}O{sub 2} addition. - Abstract: Voltammetry is a sensitive method for metal determination and one alternative to ICP MS, but its limitation is the influence of the organic matrix on the measurements. To avoid those interferences, wet digestion with H{sub 2}O{sub 2} accelerated with UV irradiation is applied and evaporation of excess of reagents is required. In this study, photolytic oxidation in quartz tubes with anatase was carried out, using as object of study wastewater samples with high amount of organic matter. Cadmium and lead determination was carried out in order to test metal recoveries. Lead recoveries reached c.a 85% for UV digestion with hydrogen peroxide, 98% for digestion with anatase immobilized with polyvinylidene fluoride (N-metylo-2-pirolidon) and c.a 103% for digestion with immobilized anatase (anatase in gum). The results obtained showed the usefulness of TiO{sub 2} layer as an oxidation medium. An easy, cheap and eco-friendly digestion method of surfactants without any reagent has been developed, with equal sensitivity but and the same detection limit of traditional digestion methods.

On solution to the problem of criticality by alternative Monte Carlo method

International Nuclear Information System (INIS)

Kyncl, J.

2005-03-01

The problem of criticality for the neutron transport equation is analyzed. The problem is transformed into an equivalent problem in a suitable set of complex functions, and the existence and uniqueness of its solution is demonstrated. The source iteration method is discussed. It is shown that the final result of the iterative process is strongly affected by the insufficient accuracy of the individual iterations. A modified method is suggested to circumvent this problem based on the theory of positive operators; the criticality problem is solved by the Monte Carlo method constructing special random process and variable so that the difference between the result and the true value can be arbitrarily small. The efficiency of this alternative method is analysed

Preconditioned alternating direction method of multipliers for inverse problems with constraints

International Nuclear Information System (INIS)

Jiao, Yuling; Jin, Qinian; Lu, Xiliang; Wang, Weijie

2017-01-01

We propose a preconditioned alternating direction method of multipliers (ADMM) to solve linear inverse problems in Hilbert spaces with constraints, where the feature of the sought solution under a linear transformation is captured by a possibly non-smooth convex function. During each iteration step, our method avoids solving large linear systems by choosing a suitable preconditioning operator. In case the data is given exactly, we prove the convergence of our preconditioned ADMM without assuming the existence of a Lagrange multiplier. In case the data is corrupted by noise, we propose a stopping rule using information on noise level and show that our preconditioned ADMM is a regularization method; we also propose a heuristic rule when the information on noise level is unavailable or unreliable and give its detailed analysis. Numerical examples are presented to test the performance of the proposed method. (paper)

A fluorescence high throughput screening method for the detection of reactive electrophiles as potential skin sensitizers

Energy Technology Data Exchange (ETDEWEB)

Avonto, Cristina; Chittiboyina, Amar G. [National Center for Natural Products Research, Research Institute of Pharmaceutical Sciences, School of Pharmacy, The University of Mississippi, University, MS 38677 (United States); Rua, Diego [The Center for Food Safety and Applied Nutrition, US Food and Drug Administration, College Park, MD 20740 (United States); Khan, Ikhlas A., E-mail: ikhan@olemiss.edu [National Center for Natural Products Research, Research Institute of Pharmaceutical Sciences, School of Pharmacy, The University of Mississippi, University, MS 38677 (United States); Division of Pharmacognosy, Department of BioMolecular Sciences, School of Pharmacy, The University of Mississippi, University, MS 38677 (United States)

2015-12-01

Skin sensitization is an important toxicological end-point in the risk assessment of chemical allergens. Because of the complexity of the biological mechanisms associated with skin sensitization, integrated approaches combining different chemical, biological and in silico methods are recommended to replace conventional animal tests. Chemical methods are intended to characterize the potential of a sensitizer to induce earlier molecular initiating events. The presence of an electrophilic mechanistic domain is considered one of the essential chemical features to covalently bind to the biological target and induce further haptenation processes. Current in chemico assays rely on the quantification of unreacted model nucleophiles after incubation with the candidate sensitizer. In the current study, a new fluorescence-based method, ‘HTS-DCYA assay’, is proposed. The assay aims at the identification of reactive electrophiles based on their chemical reactivity toward a model fluorescent thiol. The reaction workflow enabled the development of a High Throughput Screening (HTS) method to directly quantify the reaction adducts. The reaction conditions have been optimized to minimize solubility issues, oxidative side reactions and increase the throughput of the assay while minimizing the reaction time, which are common issues with existing methods. Thirty-six chemicals previously classified with LLNA, DPRA or KeratinoSens™ were tested as a proof of concept. Preliminary results gave an estimated 82% accuracy, 78% sensitivity, 90% specificity, comparable to other in chemico methods such as Cys-DPRA. In addition to validated chemicals, six natural products were analyzed and a prediction of their sensitization potential is presented for the first time. - Highlights: • A novel fluorescence-based method to detect electrophilic sensitizers is proposed. • A model fluorescent thiol was used to directly quantify the reaction products. • A discussion of the reaction workflow

A fluorescence high throughput screening method for the detection of reactive electrophiles as potential skin sensitizers

International Nuclear Information System (INIS)

Avonto, Cristina; Chittiboyina, Amar G.; Rua, Diego; Khan, Ikhlas A.

2015-01-01

Skin sensitization is an important toxicological end-point in the risk assessment of chemical allergens. Because of the complexity of the biological mechanisms associated with skin sensitization, integrated approaches combining different chemical, biological and in silico methods are recommended to replace conventional animal tests. Chemical methods are intended to characterize the potential of a sensitizer to induce earlier molecular initiating events. The presence of an electrophilic mechanistic domain is considered one of the essential chemical features to covalently bind to the biological target and induce further haptenation processes. Current in chemico assays rely on the quantification of unreacted model nucleophiles after incubation with the candidate sensitizer. In the current study, a new fluorescence-based method, ‘HTS-DCYA assay’, is proposed. The assay aims at the identification of reactive electrophiles based on their chemical reactivity toward a model fluorescent thiol. The reaction workflow enabled the development of a High Throughput Screening (HTS) method to directly quantify the reaction adducts. The reaction conditions have been optimized to minimize solubility issues, oxidative side reactions and increase the throughput of the assay while minimizing the reaction time, which are common issues with existing methods. Thirty-six chemicals previously classified with LLNA, DPRA or KeratinoSens™ were tested as a proof of concept. Preliminary results gave an estimated 82% accuracy, 78% sensitivity, 90% specificity, comparable to other in chemico methods such as Cys-DPRA. In addition to validated chemicals, six natural products were analyzed and a prediction of their sensitization potential is presented for the first time. - Highlights: • A novel fluorescence-based method to detect electrophilic sensitizers is proposed. • A model fluorescent thiol was used to directly quantify the reaction products. • A discussion of the reaction workflow

Application of perturbation methods for sensitivity analysis for nuclear power plant steam generators

International Nuclear Information System (INIS)

Gurjao, Emir Candeia

1996-02-01

The differential and GPT (Generalized Perturbation Theory) formalisms of the Perturbation Theory were applied in this work to a simplified U-tubes steam generator model to perform sensitivity analysis. The adjoint and importance equations, with the corresponding expressions for the sensitivity coefficients, were derived for this steam generator model. The system was numerically was numerically solved in a Fortran program, called GEVADJ, in order to calculate the sensitivity coefficients. A transient loss of forced primary coolant in the nuclear power plant Angra-1 was used as example case. The average and final values of functionals: secondary pressure and enthalpy were studied in relation to changes in the secondary feedwater flow, enthalpy and total volume in secondary circuit. Absolute variations in the above functionals were calculated using the perturbative methods, considering the variations in the feedwater flow and total secondary volume. Comparison with the same variations obtained via direct model showed in general good agreement, demonstrating the potentiality of perturbative methods for sensitivity analysis of nuclear systems. (author)

A sensitive new microculture method for diagnosis of cutaneous leishmaniasis.

Science.gov (United States)

Allahverdiyev, Adil M; Uzun, Soner; Bagirova, Malahat; Durdu, Murat; Memisoglu, Hamdi R

2004-03-01

A sensitive microcapillary culture method (MCM) was developed for rapid diagnosis of cutaneous leishmaniasis (CL). The MCM is superior to the traditional culture method (TCM) as determined by the smaller inoculum size, the higher sensitivity for detection of promastigotes, and the more rapid time for emergence of promastigotes. With lesion amastigote loads from grade III to 0, the positive rates and the periods for promastigote emergence were 3-4-fold higher and faster with the MCM than with the TCM, e.g., 83-97% positive in 4-7 days versus 20-40% positive in 15-30 days (P = 0.0001). The higher Pco(2) and lower Po(2) and pH presumably encourage a rapid amastigote-to-promastigote differentiation and/or the survival or growth of the latter. This MCM has the advantage of simplicity, and may be suitable for diagnostic use and for parasite retrieval in many other endemic sites where parasites are known to be difficult to grow.

Manufacturing error sensitivity analysis and optimal design method of cable-network antenna structures

Science.gov (United States)

Zong, Yali; Hu, Naigang; Duan, Baoyan; Yang, Guigeng; Cao, Hongjun; Xu, Wanye

2016-03-01

Inevitable manufacturing errors and inconsistency between assumed and actual boundary conditions can affect the shape precision and cable tensions of a cable-network antenna, and even result in failure of the structure in service. In this paper, an analytical sensitivity analysis method of the shape precision and cable tensions with respect to the parameters carrying uncertainty was studied. Based on the sensitivity analysis, an optimal design procedure was proposed to alleviate the effects of the parameters that carry uncertainty. The validity of the calculated sensitivities is examined by those computed by a finite difference method. Comparison with a traditional design method shows that the presented design procedure can remarkably reduce the influence of the uncertainties on the antenna performance. Moreover, the results suggest that especially slender front net cables, thick tension ties, relatively slender boundary cables and high tension level can improve the ability of cable-network antenna structures to resist the effects of the uncertainties on the antenna performance.

Alternative methods of synthesizing 99Tcm-labelled ciprofloxacin

International Nuclear Information System (INIS)

Kumar, V.; Choong, K.K.L.; Evans, S.; Olma, T.R.

1999-01-01

Full text: 99 Tc m -labelled ciprofloxacin (Infecton) is a new class of radiopharmaceutical designed for imaging live bacterial infection. We synthesized Infecton by modifying the procedure described by Keith Britton's group (Lancet 1996; 347: 233-235) and reported our findings at the ANZSNM meeting last year. Since the methodology was cumbersome, we investigated simpler alternative ways of labelling ciprofloxacin with 99 Tc m -pertechnetate for routine imaging. There were several limitations in the previously described method: (1) Need to prepare pure ciprofloxacin which was unstable on storage. (2) Synthetic procedure using formimidine sulphinic acid (FSA) was complicated and required boiling step. (3) The radiochemical purity (RCP) of the product was low (45-50%) requiring purification. (4) Biodistribution studies showed a marked uptake by the liver which could interfere with scan interpretation in this region. The results of our present studies showed that Infecton could be prepared by a simple two-step method: (1) Reduce 99 Tc m -pertechnetate with stannous salt (SnCl 2 or Sn-tartrate). (2) Mix with Ciproxin IV-100. The RCP of the product was up to 98%, which obviates the need for further purification. Infecton synthesized by the above method showed avid localization in abscesses induced with Staphylococcus aureus in rats. The biodistribution studies showed that Infecton was renally excreted with minimal accumulation in the liver or other organs

Limitations of amorphous content quantification by isothermal calorimetry using saturated salt solutions to control relative humidity: alternative methods.

Science.gov (United States)

Khalef, Nawel; Pinal, Rodolfo; Bakri, Aziz

2010-04-01

Despite the high sensitivity of isothermal calorimetry (IC), reported measurements of amorphous content by this technique show significant variability even for the same compound. An investigation into the reasons behind such variability is presented using amorphous lactose and salbutamol sulfate as model compounds. An analysis was carried out on the heat evolved as a result of the exchange of water vapor between the solid sample during crystallization and the saline solution reservoir. The use of saturated salt solutions as means of control of the vapor pressure of water within sealed ampoules bears inherent limitations that lead in turn to the variability associated with the IC technique. We present an alternative IC method, based on an open cell configuration that effectively addresses the limitations encountered with the sealed ampoule system. The proposed approach yields an integral whose value is proportional to the amorphous content in the sample, thus enabling reliable and consistent quantifications. 2009 Wiley-Liss, Inc. and the American Pharmacists Association

Report to the Congress on alternative methods for the Strategic Petroleum Reserve

Energy Technology Data Exchange (ETDEWEB)

1990-02-01

The purpose of this study is to fulfill the requirements of Public Law No. 101-46, approved June 30, 1989. The study describes and evaluates alternative methods for financing the future expansion of the Strategic petroleum Reserve (SPR), both to the current target level of 750 million barrels and to potential future levels of up to one billion barrels.

Notification: Notification Memo for Evaluation of Management Controls for Alternative Asbestos Control Method Experiments

Science.gov (United States)

Project #OPE-FY12-0011, February 27, 2012. This memorandum is to notify you that the Office of Inspector General (OIG) is initiating an evaluation on the Alternative Asbestos Control Method (AACM) experiments.

Alternative Assessment Methods Based on Categorizations, Supporting Technologies, and a Model for Betterment

Science.gov (United States)

Ben-Jacob, Marion G.; Ben-Jacob, Tyler E.

2014-01-01

This paper explores alternative assessment methods from the perspective of categorizations. It addresses the technologies that support assessment. It discusses initial, formative, and summative assessment, as well as objective and subjective assessment, and formal and informal assessment. It approaches each category of assessment from the…

Method and apparatus for detecting cyber attacks on an alternating current power grid

Science.gov (United States)

McEachern, Alexander; Hofmann, Ronald

2017-04-11

A method and apparatus for detecting cyber attacks on remotely-operable elements of an alternating current distribution grid. Two state estimates of the distribution grid are prepared, one of which uses micro-synchrophasors. A difference between the two state estimates indicates a possible cyber attack.

Approximate method in estimation sensitivity responses to variations in delayed neutron energy spectra

Energy Technology Data Exchange (ETDEWEB)

Yoo, J; Shin, H S; Song, T Y; Park, W S [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

Previous our numerical results in computing point kinetics equations show a possibility in developing approximations to estimate sensitivity responses of nuclear reactor. We recalculate sensitivity responses by maintaining the corrections with first order of sensitivity parameter. We present a method for computing sensitivity responses of nuclear reactor based on an approximation derived from point kinetics equations. Exploiting this approximation, we found that the first order approximation works to estimate variations in the time to reach peak power because of their linear dependence on a sensitivity parameter, and that there are errors in estimating the peak power in the first order approximation for larger sensitivity parameters. To confirm legitimacy of out approximation, these approximate results are compared with exact results obtained from out previous numerical study. 4 refs., 2 figs., 3 tabs. (Author)

Approximate method in estimation sensitivity responses to variations in delayed neutron energy spectra

Energy Technology Data Exchange (ETDEWEB)

Yoo, J.; Shin, H. S.; Song, T. Y.; Park, W. S. [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

Previous our numerical results in computing point kinetics equations show a possibility in developing approximations to estimate sensitivity responses of nuclear reactor. We recalculate sensitivity responses by maintaining the corrections with first order of sensitivity parameter. We present a method for computing sensitivity responses of nuclear reactor based on an approximation derived from point kinetics equations. Exploiting this approximation, we found that the first order approximation works to estimate variations in the time to reach peak power because of their linear dependence on a sensitivity parameter, and that there are errors in estimating the peak power in the first order approximation for larger sensitivity parameters. To confirm legitimacy of out approximation, these approximate results are compared with exact results obtained from out previous numerical study. 4 refs., 2 figs., 3 tabs. (Author)

Capillary Electrophoresis Sensitivity Enhancement Based on Adaptive Moving Average Method.

Science.gov (United States)

Drevinskas, Tomas; Telksnys, Laimutis; Maruška, Audrius; Gorbatsova, Jelena; Kaljurand, Mihkel

2018-06-05

In the present work, we demonstrate a novel approach to improve the sensitivity of the "out of lab" portable capillary electrophoretic measurements. Nowadays, many signal enhancement methods are (i) underused (nonoptimal), (ii) overused (distorts the data), or (iii) inapplicable in field-portable instrumentation because of a lack of computational power. The described innovative migration velocity-adaptive moving average method uses an optimal averaging window size and can be easily implemented with a microcontroller. The contactless conductivity detection was used as a model for the development of a signal processing method and the demonstration of its impact on the sensitivity. The frequency characteristics of the recorded electropherograms and peaks were clarified. Higher electrophoretic mobility analytes exhibit higher-frequency peaks, whereas lower electrophoretic mobility analytes exhibit lower-frequency peaks. On the basis of the obtained data, a migration velocity-adaptive moving average algorithm was created, adapted, and programmed into capillary electrophoresis data-processing software. Employing the developed algorithm, each data point is processed depending on a certain migration time of the analyte. Because of the implemented migration velocity-adaptive moving average method, the signal-to-noise ratio improved up to 11 times for sampling frequency of 4.6 Hz and up to 22 times for sampling frequency of 25 Hz. This paper could potentially be used as a methodological guideline for the development of new smoothing algorithms that require adaptive conditions in capillary electrophoresis and other separation methods.

Alternative Testing Methods for Predicting Health Risk from Environmental Exposures

Directory of Open Access Journals (Sweden)

Annamaria Colacci

2014-08-01

Full Text Available Alternative methods to animal testing are considered as promising tools to support the prediction of toxicological risks from environmental exposure. Among the alternative testing methods, the cell transformation assay (CTA appears to be one of the most appropriate approaches to predict the carcinogenic properties of single chemicals, complex mixtures and environmental pollutants. The BALB/c 3T3 CTA shows a good degree of concordance with the in vivo rodent carcinogenesis tests. Whole-genome transcriptomic profiling is performed to identify genes that are transcriptionally regulated by different kinds of exposures. Its use in cell models representative of target organs may help in understanding the mode of action and predicting the risk for human health. Aiming at associating the environmental exposure to health-adverse outcomes, we used an integrated approach including the 3T3 CTA and transcriptomics on target cells, in order to evaluate the effects of airborne particulate matter (PM on toxicological complex endpoints. Organic extracts obtained from PM2.5 and PM1 samples were evaluated in the 3T3 CTA in order to identify effects possibly associated with different aerodynamic diameters or airborne chemical components. The effects of the PM2.5 extracts on human health were assessed by using whole-genome 44 K oligo-microarray slides. Statistical analysis by GeneSpring GX identified genes whose expression was modulated in response to the cell treatment. Then, modulated genes were associated with pathways, biological processes and diseases through an extensive biological analysis. Data derived from in vitro methods and omics techniques could be valuable for monitoring the exposure to toxicants, understanding the modes of action via exposure-associated gene expression patterns and to highlight the role of genes in key events related to adversity.

Methods for the assay of plutonium in vivo: what are the alternatives

International Nuclear Information System (INIS)

Rundo, J.; Strauss, M.G.; Sherman, I.S.; Brenner, R.

1976-01-01

The problem of estimating the amount of plutonium in the human body in vivo is of considerable importance in view of the major role Pu may play in the future nuclear power program. It is a particularly difficult one because the 238 Pu and 239 Pu present in reactor-grade material emit virtually no penetrating radiation, so that conventional methods of body radioactivity measurement are useless. The existing methods of estimating Pu body burdens are reviewed and alternatives are suggested. Emphasis is placed on Pu in lung, the major problem, but reference is also made to systemically deposited Pu. Both indirect and direct methods are discussed

Circling motion and screen edges as an alternative input method for on-screen target manipulation.

Science.gov (United States)

Ka, Hyun W; Simpson, Richard C

2017-04-01

To investigate a new alternative interaction method, called circling interface, for manipulating on-screen objects. To specify a target, the user makes a circling motion around the target. To specify a desired pointing command with the circling interface, each edge of the screen is used. The user selects a command before circling the target. To evaluate the circling interface, we conducted an experiment with 16 participants, comparing the performance on pointing tasks with different combinations of selection method (circling interface, physical mouse and dwelling interface) and input device (normal computer mouse, head pointer and joystick mouse emulator). A circling interface is compatible with many types of pointing devices, not requiring physical activation of mouse buttons, and is more efficient than dwell-clicking. Across all common pointing operations, the circling interface had a tendency to produce faster performance with a head-mounted mouse emulator than with a joystick mouse. The performance accuracy of the circling interface outperformed the dwelling interface. It was demonstrated that the circling interface has the potential as another alternative pointing method for selecting and manipulating objects in a graphical user interface. Implications for Rehabilitation A circling interface will improve clinical practice by providing an alternative pointing method that does not require physically activating mouse buttons and is more efficient than dwell-clicking. The Circling interface can also work with AAC devices.

Iterative approach as alternative to S-matrix in modal methods

Science.gov (United States)

Semenikhin, Igor; Zanuccoli, Mauro

2014-12-01

The continuously increasing complexity of opto-electronic devices and the rising demands of simulation accuracy lead to the need of solving very large systems of linear equations making iterative methods promising and attractive from the computational point of view with respect to direct methods. In particular, iterative approach potentially enables the reduction of required computational time to solve Maxwell's equations by Eigenmode Expansion algorithms. Regardless of the particular eigenmodes finding method used, the expansion coefficients are computed as a rule by scattering matrix (S-matrix) approach or similar techniques requiring order of M3 operations. In this work we consider alternatives to the S-matrix technique which are based on pure iterative or mixed direct-iterative approaches. The possibility to diminish the impact of M3 -order calculations to overall time and in some cases even to reduce the number of arithmetic operations to M2 by applying iterative techniques are discussed. Numerical results are illustrated to discuss validity and potentiality of the proposed approaches.

Sensitive emission spectrometric method for the analysis of airborne particulate matter

International Nuclear Information System (INIS)

Sugimae, A.

1975-01-01

A rapid and sensitive emission spectrometric method for the routine analysis of airborne particulate matter collected on the glass fiber filter is reported. The method is a powder--dc arc technique involving no chemical pre-enrichment procedures. The elements--Ag, BA: Be, Bi, Cd, Co, Cr, Cu, Fe, Ga, La, Mn, Ni, Pb, Sn, V, Y, Yb, and Zn--were determined. (U.S.)

An alternative solver for the nodal expansion method equations - 106

International Nuclear Information System (INIS)

Carvalho da Silva, F.; Carlos Marques Alvim, A.; Senra Martinez, A.

2010-01-01

An automated procedure for nuclear reactor core design is accomplished by using a quick and accurate 3D nodal code, aiming at solving the diffusion equation, which describes the spatial neutron distribution in the reactor. This paper deals with an alternative solver for nodal expansion method (NEM), with only two inner iterations (mesh sweeps) per outer iteration, thus having the potential to reduce the time required to calculate the power distribution in nuclear reactors, but with accuracy similar to the ones found in conventional NEM. The proposed solver was implemented into a computational system which, besides solving the diffusion equation, also solves the burnup equations governing the gradual changes in material compositions of the core due to fuel depletion. Results confirm the effectiveness of the method for practical purposes. (authors)

Measuring decision weights in recognition experiments with multiple response alternatives: comparing the correlation and multinomial-logistic-regression methods.

Science.gov (United States)

Dai, Huanping; Micheyl, Christophe

2012-11-01

Psychophysical "reverse-correlation" methods allow researchers to gain insight into the perceptual representations and decision weighting strategies of individual subjects in perceptual tasks. Although these methods have gained momentum, until recently their development was limited to experiments involving only two response categories. Recently, two approaches for estimating decision weights in m-alternative experiments have been put forward. One approach extends the two-category correlation method to m > 2 alternatives; the second uses multinomial logistic regression (MLR). In this article, the relative merits of the two methods are discussed, and the issues of convergence and statistical efficiency of the methods are evaluated quantitatively using Monte Carlo simulations. The results indicate that, for a range of values of the number of trials, the estimated weighting patterns are closer to their asymptotic values for the correlation method than for the MLR method. Moreover, for the MLR method, weight estimates for different stimulus components can exhibit strong correlations, making the analysis and interpretation of measured weighting patterns less straightforward than for the correlation method. These and other advantages of the correlation method, which include computational simplicity and a close relationship to other well-established psychophysical reverse-correlation methods, make it an attractive tool to uncover decision strategies in m-alternative experiments.

Multi-criteria evaluation of cooking energy alternatives for promoting parabolic solar cooker in India

Energy Technology Data Exchange (ETDEWEB)

Pohekar, S.D. [Birla Institute of Technology and Science, Pilani (India). CREED; Ramachandran, M. [Birla Institute of Technology and Science, Dubai (United Arab Emirates)

2004-07-01

The policy formulation for cooking energy substitution by renewables is addressed in multi-criteria context. A survey is conducted to know the perceptions of different decision making groups on present dissemination of various cooking energy alternatives in India. Nine cooking energy alternatives are evaluated on 30 different criteria comprising of technical, economic, environmental/social, behavioural and commercial issues. Preference Ranking Organization METHod for Enrichment Evaluation (PROMETHEE), a multi-criteria decision making method of outranking nature is used to rank the alternatives. It is found that liquefied petroleum gas (LPG) stove is the most preferred device, followed by kerosene stove, solar box cooker and parabolic solar cooker (PSC) in that order. A sensitivity analysis is also carried out for identifying potential areas for improvement for PSC. On the basis of results, strategies for promoting wide spread use of PSC are formulated. (author)

78 FR 45253 - National Toxicology Program Scientific Advisory Committee on Alternative Toxicological Methods...

Science.gov (United States)

2013-07-26

... DEPARTMENT OF HEALTH AND HUMAN SERVICES National Institutes of Health National Toxicology Program... Alternative Methods (ICCVAM), the National Toxicology Program (NTP) Interagency Center for the Evaluation of... Director, National Toxicology Program. [FR Doc. 2013-17919 Filed 7-25-13; 8:45 am] BILLING CODE 4140-01-P ...

Alternative methods of modeling wind generation using production costing models

International Nuclear Information System (INIS)

Milligan, M.R.; Pang, C.K.

1996-08-01

This paper examines the methods of incorporating wind generation in two production costing models: one is a load duration curve (LDC) based model and the other is a chronological-based model. These two models were used to evaluate the impacts of wind generation on two utility systems using actual collected wind data at two locations with high potential for wind generation. The results are sensitive to the selected wind data and the level of benefits of wind generation is sensitive to the load forecast. The total production cost over a year obtained by the chronological approach does not differ significantly from that of the LDC approach, though the chronological commitment of units is more realistic and more accurate. Chronological models provide the capability of answering important questions about wind resources which are difficult or impossible to address with LDC models

Alternative Processes for Manufacturing of Metal Oxide-based Potentiometric Chemosensors

Directory of Open Access Journals (Sweden)

Winfried VONAU

2015-10-01

Full Text Available New possibilities for the preparation of partially selective redox electrodes based on passivated metals of the subgroups IV to VI of the periodic system are presented by the example of vanadium. The gas phase oxidation at controlled oxygen partial pressures (CPO and the pulsed laser deposition (PLD as an high-vacuum method are utilised as alternative methods beside the well- established chemical and electrochemical passivation which usually lead to the highest possible oxidation state of the passivated metal. These newly available methods enable in principle the tailoring of oxidation states in the sensitive layer and therefore the optimisation of the electrochemical sensitivity and selectivity of sensors equipped with it. The use of vanadium as basic electrode material is crucial because it shows in several matrices a remarkable corrosion susceptibility. This problem can be solved by the introduction of stable alloys with high vanadium contents. These materials can be efficiently produced by pulsed laser deposition (PLD.

Complex finite element sensitivity method for creep analysis

International Nuclear Information System (INIS)

Gomez-Farias, Armando; Montoya, Arturo; Millwater, Harry

2015-01-01

The complex finite element method (ZFEM) has been extended to perform sensitivity analysis for mechanical and structural systems undergoing creep deformation. ZFEM uses a complex finite element formulation to provide shape, material, and loading derivatives of the system response, providing an insight into the essential factors which control the behavior of the system as a function of time. A complex variable-based quadrilateral user element (UEL) subroutine implementing the power law creep constitutive formulation was incorporated within the Abaqus commercial finite element software. The results of the complex finite element computations were verified by comparing them to the reference solution for the steady-state creep problem of a thick-walled cylinder in the power law creep range. A practical application of the ZFEM implementation to creep deformation analysis is the calculation of the skeletal point of a notched bar test from a single ZFEM run. In contrast, the standard finite element procedure requires multiple runs. The value of the skeletal point is that it identifies the location where the stress state is accurate, regardless of the certainty of the creep material properties. - Highlights: • A novel finite element sensitivity method (ZFEM) for creep was introduced. • ZFEM has the capability to calculate accurate partial derivatives. • ZFEM can be used for identification of the skeletal point of creep structures. • ZFEM can be easily implemented in a commercial software, e.g. Abaqus. • ZFEM results were shown to be in excellent agreement with analytical solutions

Alternative method for assessing coking coal plasticity

Energy Technology Data Exchange (ETDEWEB)

Dzuy Nguyen; Susan Woodhouse; Merrick Mahoney [University of Adelaide (Australia). BHP Billiton Newcastle Technology Centre

2008-07-15

Traditional plasticity measurements for coal have a number of limitations associated with the reproducibility of the tests and their use in predicting coking behaviour. This report reviews alternative rheological methods for characterising the plastic behaviour of coking coals. It reviews the application of more fundamental rheological measurements to the coal system as well as reviewing applications of rheology to other physical systems. These systems may act as potential models for the application of fundamental rheological measurements to cokemaking. The systems considered were polymer melts, coal ash melts, lava, bread making and ice cream. These systems were chosen because they exhibit some physically equivalent processes to the processes occurring during cokemaking, eg, the generation of bubbles within a softened system that then resolidifies. A number of recommendations were made; the steady and oscillatory shear squeeze flow techniques be further investigated to determine if the measured rheology characteristics are related to transformations within the coke oven and the characteristics of resultant coke; modification of Gieseler plastometers for more fundamental rheology measurements not be attempted.

Measuring sensitivity in pharmacoeconomic studies. Refining point sensitivity and range sensitivity by incorporating probability distributions.

Science.gov (United States)

Nuijten, M J

1999-07-01

The aim of the present study is to describe a refinement of a previously presented method, based on the concept of point sensitivity, to deal with uncertainty in economic studies. The original method was refined by the incorporation of probability distributions which allow a more accurate assessment of the level of uncertainty in the model. In addition, a bootstrap method was used to create a probability distribution for a fixed input variable based on a limited number of data points. The original method was limited in that the sensitivity measurement was based on a uniform distribution of the variables and that the overall sensitivity measure was based on a subjectively chosen range which excludes the impact of values outside the range on the overall sensitivity. The concepts of the refined method were illustrated using a Markov model of depression. The application of the refined method substantially changed the ranking of the most sensitive variables compared with the original method. The response rate became the most sensitive variable instead of the 'per diem' for hospitalisation. The refinement of the original method yields sensitivity outcomes, which greater reflect the real uncertainty in economic studies.

An adjoint method of sensitivity analysis for residual vibrations of structures subject to impacts

Science.gov (United States)

Yan, Kun; Cheng, Gengdong

2018-03-01

For structures subject to impact loads, the residual vibration reduction is more and more important as the machines become faster and lighter. An efficient sensitivity analysis of residual vibration with respect to structural or operational parameters is indispensable for using a gradient based optimization algorithm, which reduces the residual vibration in either active or passive way. In this paper, an integrated quadratic performance index is used as the measure of the residual vibration, since it globally measures the residual vibration response and its calculation can be simplified greatly with Lyapunov equation. Several sensitivity analysis approaches for performance index were developed based on the assumption that the initial excitations of residual vibration were given and independent of structural design. Since the resulting excitations by the impact load often depend on structural design, this paper aims to propose a new efficient sensitivity analysis method for residual vibration of structures subject to impacts to consider the dependence. The new method is developed by combining two existing methods and using adjoint variable approach. Three numerical examples are carried out and demonstrate the accuracy of the proposed method. The numerical results show that the dependence of initial excitations on structural design variables may strongly affects the accuracy of sensitivities.

An Alternative Method to Compute the Bit Error Probability of Modulation Schemes Subject to Nakagami- Fading

Directory of Open Access Journals (Sweden)

Madeiro Francisco

2010-01-01

Full Text Available Abstract This paper presents an alternative method for determining exact expressions for the bit error probability (BEP of modulation schemes subject to Nakagami- fading. In this method, the Nakagami- fading channel is seen as an additive noise channel whose noise is modeled as the ratio between Gaussian and Nakagami- random variables. The method consists of using the cumulative density function of the resulting noise to obtain closed-form expressions for the BEP of modulation schemes subject to Nakagami- fading. In particular, the proposed method is used to obtain closed-form expressions for the BEP of -ary quadrature amplitude modulation ( -QAM, -ary pulse amplitude modulation ( -PAM, and rectangular quadrature amplitude modulation ( -QAM under Nakagami- fading. The main contribution of this paper is to show that this alternative method can be used to reduce the computational complexity for detecting signals in the presence of fading.

Isolation of uv-sensitive variants of human FL cells by a viral suicide method

International Nuclear Information System (INIS)

Shiomi, T.; Sato, K.

1979-01-01

A new method (viral suicide method) for the isolation of uv-sensitive mutants is described. Colonies of mutagenized human FL cells were infected with uv-irradiated Herpes simplex viruses and surviving ones which seemed to be deficient in host cell reactivation (HCR) were examined for their uv sensitivity. Nineteen of 238 clones examined were sensitive to uv irradiation at the time of the isolation. After recloning, four of these clones have been studied and two (UVS-1 and UVS-2) of them are stable in their uv sensitivity for 4 months in culture. uv sensitivity of UVS-1, UVS-2, and the parental FL cells are as follows: the extrapolation numbers (n) are 2.2, 2.1, and 1.8 and mean lethal doses (DO) are 2.9, 3.7, and 7.8 J/m 2 for UVS-1, UVS-2, and the parental FL cells, respectively. They are no more sensitive than FL cells to x-irradiation. The ability of HCR in UVS-2 cells is apparently lower than that in FL cells, whereas UVS-1 cells are the same as FL cells in the ability

Easy method enhancing the sensitivity of a helium mass-spectrometer leak detector

International Nuclear Information System (INIS)

Firpo, G.; Pozzo, A.

2004-01-01

Commercial He mass spectrometer leak detectors usually do not provide sufficient sensitivity to perform accurate measurements of the permeation rate of He through glass. Ultrasensitive dedicated systems have adeguate sensitivity but involve high costs and complex procedures. However, both cryogenics and photomultiplier technology routinely demand this goal. Here, we propose a novel method to increase the sensitivity of commercial devices to easily measure accurate permeation rate. We modified a commercial leak detector by reducing the pumping speed at the inlet of the rotary pump, thus increasing its sensitivity by one order of magnitude. The modified detector was used to measure the leak rate of the permeation of He through the glass walls of a photomultiplier. Further improvements made to decrease the minimum detectable signal were limited by the high ultimate pressure in the spectrometer tube

Alternative methods for ray tracing in uniaxial media. Application to negative refraction

Science.gov (United States)

Bellver-Cebreros, Consuelo; Rodriguez-Danta, Marcelo

2007-03-01

In previous papers [C. Bellver-Cebreros, M. Rodriguez-Danta, Eikonal equation, alternative expression of Fresnel's equation and Mohr's construction in optical anisotropic media, Opt. Commun. 189 (2001) 193; C. Bellver-Cebreros, M. Rodriguez-Danta, Internal conical refraction in biaxial media and graphical plane constructions deduced from Mohr's method, Opt. Commun. 212 (2002) 199; C. Bellver-Cebreros, M. Rodriguez-Danta, Refraccion conica externa en medios biaxicos a partir de la construccion de Mohr, Opt. Pura AppliE 36 (2003) 33], the authors have developed a method based on the local properties of dielectric permittivity tensor and on Mohr's plane graphical construction in order to study the behaviour of locally plane light waves in anisotropic media. In this paper, this alternative methodology is compared with the traditional one, by emphasizing the simplicity of the former when studying ray propagation through uniaxial media (comparison is possible since, in this case, traditional construction becomes also plane). An original and simple graphical method is proposed in order to determine the direction of propagation given by the wave vector from the knowledge of the extraordinary ray direction (given by Poynting vector). Some properties of light rays in these media not described in the literature are obtained. Finally, two applications are considered: a description of optical birefringence under normal incidence and the study of negative refraction in uniaxial media.

EPA Releases Draft Policy to Reduce Animal Testing for Skin Sensitization

Science.gov (United States)

The document, Draft Interim Science Policy: Use of Alternative Approaches for Skin Sensitization as a Replacement for Laboratory Animal Testing, describes the science behind the non-animal alternatives that can now be used to identify skin sensitization.

Isolation of UV-sensitive mutants of mouse L5178Y cells by a cell suspension spotting method

International Nuclear Information System (INIS)

Shiomi, T.; Hieda-Shiomi, N.; Sato, K.

1982-01-01

We have isolated 56 UV-sensitive mutant clones from a mouse L51 T/t line of L5178Y cells by a cell suspension spotting method. Five mutants have also been isolated from L51 T/t and L5178Y cells by the method reported by Thompson and coworkers. We divided the mutants into two groups, highly sensitive and moderately sensitive mutants, according to their sensitivity to UV irradiation. Fifty-eight mutants were highly sensitive and three were moderately sensitive to UV. The reconstruction experiments indicate that more than 90% of highly sensitive mutants were recovered by the cell suspension spotting method. Frequencies of recovered mutants highly sensitive to UV increased with increasing dose of mutagens. Recovered mutant frequency reached 10(-2) after treatment with 1.5 micrograms/ml of N-methyl-N'-nitro-N-nitrosoguanidine (MNNG) (survival 0.2%). Eight UV-sensitive mutants were divided into four complementation groups. These mutants were 2-6 times more sensitive to UV than parental L51 T/t cells in terms of D37 (dose required to reduce survival to 37%). Four representative UV-sensitive mutants which are classified into different complementation groups were examined for their sensitivity to killing by UV, 4-nitroquinoline-1-oxide (4NQO), mitomycin C (MMC), X-rays, and MNNG. All four classes of mutants were found to be cross-sensitive to UV, 4NQO, and MMC, but not sensitive to X-rays and MNNG

Sensitivity-based virtual fields for the non-linear virtual fields method

Science.gov (United States)

Marek, Aleksander; Davis, Frances M.; Pierron, Fabrice

2017-09-01

The virtual fields method is an approach to inversely identify material parameters using full-field deformation data. In this manuscript, a new set of automatically-defined virtual fields for non-linear constitutive models has been proposed. These new sensitivity-based virtual fields reduce the influence of noise on the parameter identification. The sensitivity-based virtual fields were applied to a numerical example involving small strain plasticity; however, the general formulation derived for these virtual fields is applicable to any non-linear constitutive model. To quantify the improvement offered by these new virtual fields, they were compared with stiffness-based and manually defined virtual fields. The proposed sensitivity-based virtual fields were consistently able to identify plastic model parameters and outperform the stiffness-based and manually defined virtual fields when the data was corrupted by noise.

How Many Alternatives Can Be Ranked? A Comparison of the Paired Comparison and Ranking Methods.

Science.gov (United States)

Ock, Minsu; Yi, Nari; Ahn, Jeonghoon; Jo, Min-Woo

2016-01-01

To determine the feasibility of converting ranking data into paired comparison (PC) data and suggest the number of alternatives that can be ranked by comparing a PC and a ranking method. Using a total of 222 health states, a household survey was conducted in a sample of 300 individuals from the general population. Each respondent performed a PC 15 times and a ranking method 6 times (two attempts of ranking three, four, and five health states, respectively). The health states of the PC and the ranking method were constructed to overlap each other. We converted the ranked data into PC data and examined the consistency of the response rate. Applying probit regression, we obtained the predicted probability of each method. Pearson correlation coefficients were determined between the predicted probabilities of those methods. The mean absolute error was also assessed between the observed and the predicted values. The overall consistency of the response rate was 82.8%. The Pearson correlation coefficients were 0.789, 0.852, and 0.893 for ranking three, four, and five health states, respectively. The lowest mean absolute error was 0.082 (95% confidence interval [CI] 0.074-0.090) in ranking five health states, followed by 0.123 (95% CI 0.111-0.135) in ranking four health states and 0.126 (95% CI 0.113-0.138) in ranking three health states. After empirically examining the consistency of the response rate between a PC and a ranking method, we suggest that using five alternatives in the ranking method may be superior to using three or four alternatives. Copyright © 2016 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Sensitivity Analysis and Bounding of Causal Effects with Alternative Identifying Assumptions

Science.gov (United States)

Jo, Booil; Vinokur, Amiram D.

2011-01-01

When identification of causal effects relies on untestable assumptions regarding nonidentified parameters, sensitivity of causal effect estimates is often questioned. For proper interpretation of causal effect estimates in this situation, deriving bounds on causal parameters or exploring the sensitivity of estimates to scientifically plausible…

Ectoparasites of medical and veterinary importance: drug resistance and the need for alternative control methods.

Science.gov (United States)

McNair, Carol M

2015-03-01

Despite multiple attempts at eradication, many ectoparasites of humans and domestic livestock remain a persistent problem in the modern world. For many years, a range of pesticide drugs including organophosphates, organochlorides and synthetic pyrethroids provided effective control of these parasites; but intensive use of these drugs has led to the evolution of resistance in many target species. This paper aims to review the effectiveness of current control methods and discuss potential alternatives for the long term sustainable control of ectoparasites. Important medical ectoparasites such as scabies mites, head lice and bed bugs present a significant public health problem, and so adequate control methods are essential. Ectoparasites of domestic livestock and farmed fish (for example sheep scab mites, poultry mites and sea lice) are also of concern given the increasing strain on the world's food supply. These parasites have become resistant to several classes of pesticide, making control very difficult. Recently, an increasing amount of research has focussed on alternative control methods such as insect growth regulators, biological control using essential oils or fungi, as well as vaccine development against some ectoparasites of medical and veterinary importance. Drug resistance is prevalent in all of the ectoparasites discussed in this review. A wide variety of alternative control methods have been identified, however further research is necessary in order for these to be used to successfully control ectoparasitic diseases in the future. © 2015 Royal Pharmaceutical Society.

Sensitivity and Uncertainty Analysis of Coupled Reactor Physics Problems : Method Development for Multi-Physics in Reactors

NARCIS (Netherlands)

Perkó, Z.

2015-01-01

This thesis presents novel adjoint and spectral methods for the sensitivity and uncertainty (S&U) analysis of multi-physics problems encountered in the field of reactor physics. The first part focuses on the steady state of reactors and extends the adjoint sensitivity analysis methods well

Probabilistic sensitivity analysis incorporating the bootstrap: an example comparing treatments for the eradication of Helicobacter pylori.

Science.gov (United States)

Pasta, D J; Taylor, J L; Henning, J M

1999-01-01

Decision-analytic models are frequently used to evaluate the relative costs and benefits of alternative therapeutic strategies for health care. Various types of sensitivity analysis are used to evaluate the uncertainty inherent in the models. Although probabilistic sensitivity analysis is more difficult theoretically and computationally, the results can be much more powerful and useful than deterministic sensitivity analysis. The authors show how a Monte Carlo simulation can be implemented using standard software to perform a probabilistic sensitivity analysis incorporating the bootstrap. The method is applied to a decision-analytic model evaluating the cost-effectiveness of Helicobacter pylori eradication. The necessary steps are straightforward and are described in detail. The use of the bootstrap avoids certain difficulties encountered with theoretical distributions. The probabilistic sensitivity analysis provided insights into the decision-analytic model beyond the traditional base-case and deterministic sensitivity analyses and should become the standard method for assessing sensitivity.

A sensitive method for assay of beryllium with chromazurol S and 2,2'-bipyridyl

International Nuclear Information System (INIS)

Buhl, F.; Kwapulinska, G.

1980-01-01

A spectrophotometric method of assay for microgram amounts of beryllium by means of chromazurol S in presence of 2,2'-bipyridyl was described. The latter appreciably enhances the sensitivity of the method; epsilonsub(lambda=610nm) is 5.4X10 4 . The complex compound obeys the Lambert-Beer law in the concentration range 0.002 to 0.2 ppm Be. The maximum colour intensity is immediately attained at pH 5. The molar ratio Be: CHAS: bip is 1 : 2 : 1. The suggested method is sensitive and has satisfactory selectivity when EDTA is applied as masking agent. (author)

Dynamic pressure sensitivity determination with Mach number method

Science.gov (United States)

Sarraf, Christophe; Damion, Jean-Pierre

2018-05-01

Measurements of pressure in fast transient conditions are often performed even if the dynamic characteristic of the transducer are not traceable to international standards. Moreover, the question of a primary standard in dynamic pressure is still open, especially for gaseous applications. The question is to improve dynamic standards in order to respond to expressed industrial needs. In this paper, the method proposed in the EMRP IND09 ‘Dynamic’ project, which can be called the ‘ideal shock tube method’, is compared with the ‘collective standard method’ currently used in the Laboratoire de Métrologie Dynamique (LNE/ENSAM). The input is a step of pressure generated by a shock tube. The transducer is a piezoelectric pressure sensor. With the ‘ideal shock tube method’ the sensitivity of a pressure sensor is first determined dynamically. This method requires a shock tube implemented with piezoelectric shock wave detectors. The measurement of the Mach number in the tube allows an evaluation of the incident pressure amplitude of a step using a theoretical 1D model of the shock tube. Heat transfer, other actual effects and effects of the shock tube imperfections are not taken into account. The amplitude of the pressure step is then used to determine the sensitivity in dynamic conditions. The second method uses a frequency bandwidth comparison to determine pressure at frequencies from quasi-static conditions, traceable to static pressure standards, to higher frequencies (up to 10 kHz). The measurand is also a step of pressure generated by a supposed ideal shock tube or a fast-opening device. The results are provided as a transfer function with an uncertainty budget assigned to a frequency range, also deliverable frequency by frequency. The largest uncertainty in the bandwidth of comparison is used to trace the final pressure step level measured in dynamic conditions, owing that this pressure is not measurable in a steady state on a shock tube. A reference

A nanosilver-based spectrophotometry method for sensitive determination of tartrazine in food samples.

Science.gov (United States)

Sahraei, R; Farmany, A; Mortazavi, S S

2013-06-01

A new method is reported for sensitive determination of tartrazine in the food samples. The method is based on the catalytic effect of silver nanoparticle (AgNPs) on the oxidation reaction of tartrazine by potassium iodate in the acetate buffer medium. The reaction is followed spectrophotometrically by measuring the change in absorbance (ΔA) at 420 nm using a fixed time method (70 s). The reaction variables were optimised in order to achieve the highest sensitivity. The thirty six criterion detection limit was 0.3 ng/mL, and the relative standard deviation for ten replicate measurements of 30 ng/mL of tartrazine was 0.98% (n=10). The method was successfully applied to the determination of tartrazine in lemon, and papaya-flavoured gelatin, candy, and in fruit syrup. Copyright © 2012 Elsevier Ltd. All rights reserved.

Facile fabrication of controllable zinc oxide nanorod clusters on polyacrylonitrile nanofibers via repeatedly alternating immersion method

Energy Technology Data Exchange (ETDEWEB)

Zhou, Ying; Li, Xia; Yu, Hou-Yong, E-mail: phdyu@zstu.edu.cn [Zhejiang Sci-Tech University, The Key Laboratory of Advanced Textile Materials and Manufacturing Technology of Ministry of Education, College of Materials and Textiles (China); Hu, Guo-Liang; Yao, Ju-Ming, E-mail: yaoj@zstu.edu.cn [Zhejiang Sci-Tech University, National Engineering Lab for Textile Fiber Materials and Processing Technology (China)

2016-12-15

Polyacrylonitrile/zinc oxide (PAN/ZnO) composite nanofiber membranes with different ZnO morphologies were fabricated by repeatedly alternating hot–cold immersion and single alternating hot–cold immersion methods. The influence of the PAN/ZnCl{sub 2} ratio and different immersion methods on the morphology, microstructure, and properties of the nanofiber membranes was investigated by using field-emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) analysis, thermogravimetric analysis (TGA), and ultraviolet–visible (UV–Vis) spectroscopy. A possible mechanism for different morphologies of PAN/ZnO nanofiber membranes with different PAN/ZnCl{sub 2} ratio through different immersion processes was presented, and well-dispersed ZnO nanorod clusters with smallest average dimeter of 115 nm and hexagonal wurtzite structure were successfully anchored onto the PAN nanofiber surface for R-7/1 nanofiber membrane. Compared to S-5/1 prepared by single alternating hot–cold immersion method, the PAN/ZnO nanofiber membrane fabricated by repeatedly alternating hot–cold immersion method (especially for R-7/1) showed improved thermal stability and high photocatalytic activity for methylene blue (MB). Compared to S-5/1, decomposition temperature at 5% weight loss (T{sub 5%}) was increased by 43 °C from 282 to 325 °C for R-7/1; meanwhile, R-7/1 showed higher photocatalytic degradation ratio of approximately 100% (after UV light irradiation for 8 h) than 65% for S-5/1 even after irradiation for 14 h. Moreover, the degradation efficiency of R-7/1 with good reuse stability remained above 94% after 3 cycles.

The Role of Numerical Methods in the Sensitivity Analysis of a ...

African Journals Online (AJOL)

The mathematical modelling of physiochemical interaction in the framework of industrial and environmental physics which relies on an initial value problem is defined by a first order ordinary differential equation. Two numerical methods of studying sensitivity analysis of physiochemical interaction data are developed.

An alternative method for centrifugal compressor loading factor modelling

Science.gov (United States)

Galerkin, Y.; Drozdov, A.; Rekstin, A.; Soldatova, K.

2017-08-01

The loading factor at design point is calculated by one or other empirical formula in classical design methods. Performance modelling as a whole is out of consideration. Test data of compressor stages demonstrates that loading factor versus flow coefficient at the impeller exit has a linear character independent of compressibility. Known Universal Modelling Method exploits this fact. Two points define the function - loading factor at design point and at zero flow rate. The proper formulae include empirical coefficients. A good modelling result is possible if the choice of coefficients is based on experience and close analogs. Earlier Y. Galerkin and K. Soldatova had proposed to define loading factor performance by the angle of its inclination to the ordinate axis and by the loading factor at zero flow rate. Simple and definite equations with four geometry parameters were proposed for loading factor performance calculated for inviscid flow. The authors of this publication have studied the test performance of thirteen stages of different types. The equations are proposed with universal empirical coefficients. The calculation error lies in the range of plus to minus 1,5%. The alternative model of a loading factor performance modelling is included in new versions of the Universal Modelling Method.

A sensitive fluorescence quenching method for determination of bismuth with tiron

Energy Technology Data Exchange (ETDEWEB)

Taher, Mohammad Ali; Rahimi, Mina [Department of Chemistry, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Fazelirad, Hamid, E-mail: hamidfazelirad@gmail.com [Department of Chemistry, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Department of Chemistry, Science and Research Branch, Islamic Azad University, Yazd (Iran, Islamic Republic of); Young Researchers Society, Shahid Bahonar University of Kerman, P.O. Box 76175-133, Kerman (Iran, Islamic Republic of)

2014-01-15

We describe a fluorescence quenching method for determination of bismuth with tiron. The method is based on the reaction of tiron by bismuth(III) in acidic media. The influence of variables such as the pH, type of buffer, tiron concentration, reaction time and temperature were investigated. Under optimized conditions, the fluorescence quenching extent is proportional to the concentration of bismuth for Bi–tiron system at the range 0.13–2.09 μg mL{sup −1} and the detection limit is 0.05 μg mL{sup −1}. The proposed sensor presented good repeatability, evaluated in terms of relative standard deviation (R.S.D.=±0.498%) for 11 replicates. This sensitive, rapid and accurate method has been successfully applied to the determination of trace bismuth(III) in water and hair samples and certified reference materials. -- Highlights: • No previous paper report on use of fluorescence quenching for determination of Bi. • Fluorescence quenching of trion is a sensitive method for determination of Bi(III). • Under the optimum conditions the detection limit is very low (0.05 μg mL{sup −1}). • The procedure is simple and safe and has high tolerance limit to interferences.

Calibration method of the pulsed X-ray relative sensitivity for ST401 plastic scintillators

International Nuclear Information System (INIS)

Xie Hongwei; Song Guzhou; Wang Kuilu

2011-01-01

The relative sensitivity calibration method of the pulsed X-ray in ST401 plastic scintillator is presented. Experimental relative sensitivity calibrations of the plastic scintillators of different thicknesses from 1 mm to 50 mm are accomplished on the 'Chenguang' pulsed X-ray source and a Co radioactive source, The uncertainty of the calibration data is evaluated, which can be treated as the experimental evidence for the relative sensitivity conversion of ST401 plastic scintillator. (authors)

Two-tiered keratinocyte assay: IL-18 production by NCTC2544 cells to determine the skin sensitizing capacity and an epidermal equivalent assay to determine sensitizer potency

DEFF Research Database (Denmark)

Teunis, Marc; Corsini, Emanuela; Smits, Mieke

2012-01-01

the use of animals. The aim of the EU FP6 Integrated Project Sens-it-iv was to develop and optimize an integrated testing strategy consisting of in vitro, human cell based assays which will closely mimic sensitization mechanisms in vivo. These assays should be an alternative approach to the LLNA. The NCTC...... method to the LLNA. Both assays are based on the use of human keratinocytes, which have been shown, over the last two decades, to play a key role in all phases of skin sensitization. First, 4 known chemicals were tested during a transferability study in which 6 laboratories participated. Three...

Application of a path sensitizing method on automated generation of test specifications for control software

International Nuclear Information System (INIS)

Morimoto, Yuuichi; Fukuda, Mitsuko

1995-01-01

An automated generation method for test specifications has been developed for sequential control software in plant control equipment. Sequential control software can be represented as sequential circuits. The control software implemented in a control equipment is designed from these circuit diagrams. In logic tests of VLSI's, path sensitizing methods are widely used to generate test specifications. But the method generates test specifications at a single time only, and can not be directly applied to sequential control software. The basic idea of the proposed method is as follows. Specifications of each logic operator in the diagrams are defined in the software design process. Therefore, test specifications of each operator in the control software can be determined from these specifications, and validity of software can be judged by inspecting all of the operators in the logic circuit diagrams. Candidates for sensitized paths, on which test data for each operator propagates, can be generated by the path sensitizing method. To confirm feasibility of the method, it was experimentally applied to control software in digital control equipment. The program could generate test specifications exactly, and feasibility of the method was confirmed. (orig.) (3 refs., 7 figs.)

The effect of uncertainties in distance-based ranking methods for multi-criteria decision making

Science.gov (United States)

Jaini, Nor I.; Utyuzhnikov, Sergei V.

2017-08-01

Data in the multi-criteria decision making are often imprecise and changeable. Therefore, it is important to carry out sensitivity analysis test for the multi-criteria decision making problem. The paper aims to present a sensitivity analysis for some ranking techniques based on the distance measures in multi-criteria decision making. Two types of uncertainties are considered for the sensitivity analysis test. The first uncertainty is related to the input data, while the second uncertainty is towards the Decision Maker preferences (weights). The ranking techniques considered in this study are TOPSIS, the relative distance and trade-off ranking methods. TOPSIS and the relative distance method measure a distance from an alternative to the ideal and antiideal solutions. In turn, the trade-off ranking calculates a distance of an alternative to the extreme solutions and other alternatives. Several test cases are considered to study the performance of each ranking technique in both types of uncertainties.

76 FR 65382 - Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline

Science.gov (United States)

2011-10-21

... Regulation of Fuel and Fuel Additives: Alternative Test Method for Olefins in Gasoline AGENCY: Environmental... gasoline. This final rule will provide flexibility to the regulated community by allowing an additional... Method for Olefins in Gasoline III. Statutory and Executive Order Reviews A. Executive Order 12866...

Method matters: systematic effects of testing procedure on visual working memory sensitivity.

Science.gov (United States)

Makovski, Tal; Watson, Leah M; Koutstaal, Wilma; Jiang, Yuhong V

2010-11-01

Visual working memory (WM) is traditionally considered a robust form of visual representation that survives changes in object motion, observer's position, and other visual transients. This article presents data that are inconsistent with the traditional view. We show that memory sensitivity is dramatically influenced by small variations in the testing procedure, supporting the idea that representations in visual WM are susceptible to interference from testing. In the study, participants were shown an array of colors to remember. After a short retention interval, memory for one of the items was tested with either a same-different task or a 2-alternative-forced-choice (2AFC) task. Memory sensitivity was much lower in the 2AFC task than in the same-different task. This difference was found regardless of encoding similarity or of whether visual WM required a fine or coarse memory resolution. The 2AFC disadvantage was reduced when participants were informed shortly before testing which item would be probed. The 2AFC disadvantage diminished in perceptual tasks and was not found in tasks probing visual long-term memory. These results support memory models that acknowledge the labile nature of visual WM and have implications for the format of visual WM and its assessment. (c) 2010 APA, all rights reserved

Overview of hybrid subspace methods for uncertainty quantification, sensitivity analysis

International Nuclear Information System (INIS)

Abdel-Khalik, Hany S.; Bang, Youngsuk; Wang, Congjian

2013-01-01

Highlights: ► We overview the state-of-the-art in uncertainty quantification and sensitivity analysis. ► We overview new developments in above areas using hybrid methods. ► We give a tutorial introduction to above areas and the new developments. ► Hybrid methods address the explosion in dimensionality in nonlinear models. ► Representative numerical experiments are given. -- Abstract: The role of modeling and simulation has been heavily promoted in recent years to improve understanding of complex engineering systems. To realize the benefits of modeling and simulation, concerted efforts in the areas of uncertainty quantification and sensitivity analysis are required. The manuscript intends to serve as a pedagogical presentation of the material to young researchers and practitioners with little background on the subjects. We believe this is important as the role of these subjects is expected to be integral to the design, safety, and operation of existing as well as next generation reactors. In addition to covering the basics, an overview of the current state-of-the-art will be given with particular emphasis on the challenges pertaining to nuclear reactor modeling. The second objective will focus on presenting our own development of hybrid subspace methods intended to address the explosion in the computational overhead required when handling real-world complex engineering systems.

Phototoxicity: Its Mechanism and Animal Alternative Test Methods

Science.gov (United States)

Park, Hyeonji; Lim, Kyung-Min

2015-01-01

The skin exposure to solar irradiation and photoreactive xenobiotics may produce abnormal skin reaction, phototoxicity. Phototoxicity is an acute light-induced response, which occurs when photoreacive chemicals are activated by solar lights and transformed into products cytotoxic against the skin cells. Multifarious symptoms of phototoxicity are identified, skin irritation, erythema, pruritis, and edema that are similar to those of the exaggerated sunburn. Diverse organic chemicals, especially drugs, are known to induce phototoxicity, which is probably from the common possession of UV-absorbing benzene or heterocyclic rings in their molecular structures. Both UVB (290~320 nm) and UVA (320~400 nm) are responsible for the manifestation of phototoxicity. Absorption of photons and absorbed energy (hv) by photoactive chemicals results in molecular changes or generates reactive oxygen species and depending on the way how endogenous molecules are affected by phototoxicants, mechanisms of phototoxcity is categorized into two modes of action: Direct when unstable species from excited state directly react with the endogenous molecules, and indirect when endogeneous molecules react with secondary photoproducts. In order to identify phototoxic potential of a chemical, various test methods have been introduced. Focus is given to animal alternative test methods, i.e., in vitro, and in chemico assays as well as in vivo. 3T3 neutral red uptake assay, erythrocyte photohemolysis test, and phototoxicity test using human 3-dimensional (3D) epidermis model are examples of in vitro assays. In chemico methods evaluate the generation of reactive oxygen species or DNA strand break activity employing plasmid for chemicals, or drugs with phototoxic potential. PMID:26191378

Debate as an alternative method for medical literature evaluation.

Science.gov (United States)

Toor, Rebecca; Samai, Kathryn; Wargo, Ryan

2017-05-01

To determine the student impression of utilizing a debate style journal club as an alternative approach for preceptors to teach medical literature evaluation skills to pharmacy students undergoing Advance Pharmacy Practice Experiences (APPE) in both acute care and ambulatory care. Students were asked to debate on a controversial topic or two drugs with similar indications. Each side had to research supporting evidence based medicine and use literature appraisal skills to incorporate the information logically into an oral debate style format. Approximately fifteen minutes were allotted for each debate, allowing five minutes for each opening argument, three minutes for each rebuttal, and two minutes for each closing argument. Students were then asked to complete a post-debate survey using a Likert Scale to evaluate their perception of the debate style journal club. Following implementation of the debate style journal club, students reported being more confident with their ability to find, compare, and retain information from primary literature with a mean of 4.1, 4.2, and 4.4 respectively on a Likert Scale. Students also reported overall enjoyment and satisfaction with a mean of 4.0. Debate style journal clubs have the capability to teach pharmacy students vital literature appraisal skills, and are a well-liked alternative to the traditional style journal club. Incorporating this method improved student interest as well as increased their ability to find, compare, and retain the information gathered from primary literature. Copyright © 2017 Elsevier Inc. All rights reserved.

Overview of methods for uncertainty analysis and sensitivity analysis in probabilistic risk assessment

International Nuclear Information System (INIS)

Iman, R.L.; Helton, J.C.

1985-01-01

Probabilistic Risk Assessment (PRA) is playing an increasingly important role in the nuclear reactor regulatory process. The assessment of uncertainties associated with PRA results is widely recognized as an important part of the analysis process. One of the major criticisms of the Reactor Safety Study was that its representation of uncertainty was inadequate. The desire for the capability to treat uncertainties with the MELCOR risk code being developed at Sandia National Laboratories is indicative of the current interest in this topic. However, as yet, uncertainty analysis and sensitivity analysis in the context of PRA is a relatively immature field. In this paper, available methods for uncertainty analysis and sensitivity analysis in a PRA are reviewed. This review first treats methods for use with individual components of a PRA and then considers how these methods could be combined in the performance of a complete PRA. In the context of this paper, the goal of uncertainty analysis is to measure the imprecision in PRA outcomes of interest, and the goal of sensitivity analysis is to identify the major contributors to this imprecision. There are a number of areas that must be considered in uncertainty analysis and sensitivity analysis for a PRA: (1) information, (2) systems analysis, (3) thermal-hydraulic phenomena/fission product behavior, (4) health and economic consequences, and (5) display of results. Each of these areas and the synthesis of them into a complete PRA are discussed

Alternative normalization methods demonstrate widespread cortical hypometabolism in untreated de novo Parkinson's disease

DEFF Research Database (Denmark)

Berti, Valentina; Polito, C; Borghammer, Per

2012-01-01

, recent studies suggested that conventional data normalization procedures may not always be valid, and demonstrated that alternative normalization strategies better allow detection of low magnitude changes. We hypothesized that these alternative normalization procedures would disclose more widespread...... metabolic alterations in de novo PD. METHODS: [18F]FDG PET scans of 26 untreated de novo PD patients (Hoehn & Yahr stage I-II) and 21 age-matched controls were compared using voxel-based analysis. Normalization was performed using gray matter (GM), white matter (WM) reference regions and Yakushev...... normalization. RESULTS: Compared to GM normalization, WM and Yakushev normalization procedures disclosed much larger cortical regions of relative hypometabolism in the PD group with extensive involvement of frontal and parieto-temporal-occipital cortices, and several subcortical structures. Furthermore...

Lower growth temperature increases alternative pathway capacity and alternative oxidase protein in tobacco.

Science.gov (United States)

Vanlerberghe, G C; McIntosh, L

1992-09-01

Suspension cells of NT1 tobacco (Nicotiana tabacum L. cv bright yellow) have been used to study the effect of growth temperature on the CN-resistant, salicylhydroxamic acid-sensitive alternative pathway of respiration. Mitochondria isolated from cells maintained at 30 degrees C had a low capacity to oxidize succinate via the alternative pathway, whereas mitochondria isolated from cells 24 h after transfer to 18 degrees C displayed, on average, a 5-fold increase in this capacity (from 7 to 32 nanoatoms oxygen per milligram protein per minute). This represented an increase in alternative pathway capacity from 18 to 45% of the total capacity of electron transport. This increased capacity was lost upon transfer of cells back to 30 degrees C. A monoclonal antibody to the terminal oxidase of the alternative pathway (the alternative oxidase) from Sauromatum guttatum (T.E. Elthon, R.L. Nickels, L. McIntosh [1989] Plant Physiology 89: 1311-1317) recognized a 35-kilodalton mitochondrial protein in tobacco. There was an excellent correlation between the capacity of the alternative path in isolated tobacco mitochondria and the levels of this 35-kilodalton alternative oxidase protein. Cycloheximide could inhibit both the increased level of the 35-kilodalton alternative oxidase protein and the increased alternative pathway capacity normally seen upon transfer to 18 degrees C. We conclude that transfer of tobacco cells to the lower temperature increases the capacity of the alternative pathway due, at least in part, to de novo synthesis of the 35-kilodalton alternative oxidase protein.

Non-animal methods to predict skin sensitization (I): the Cosmetics Europe database.

Science.gov (United States)

Hoffmann, Sebastian; Kleinstreuer, Nicole; Alépée, Nathalie; Allen, David; Api, Anne Marie; Ashikaga, Takao; Clouet, Elodie; Cluzel, Magalie; Desprez, Bertrand; Gellatly, Nichola; Goebel, Carsten; Kern, Petra S; Klaric, Martina; Kühnl, Jochen; Lalko, Jon F; Martinozzi-Teissier, Silvia; Mewes, Karsten; Miyazawa, Masaaki; Parakhia, Rahul; van Vliet, Erwin; Zang, Qingda; Petersohn, Dirk

2018-05-01

Cosmetics Europe, the European Trade Association for the cosmetics and personal care industry, is conducting a multi-phase program to develop regulatory accepted, animal-free testing strategies enabling the cosmetics industry to conduct safety assessments. Based on a systematic evaluation of test methods for skin sensitization, five non-animal test methods (DPRA (Direct Peptide Reactivity Assay), KeratinoSens TM , h-CLAT (human cell line activation test), U-SENS TM , SENS-IS) were selected for inclusion in a comprehensive database of 128 substances. Existing data were compiled and completed with newly generated data, the latter amounting to one-third of all data. The database was complemented with human and local lymph node assay (LLNA) reference data, physicochemical properties and use categories, and thoroughly curated. Focused on the availability of human data, the substance selection resulted nevertheless resulted in a high diversity of chemistries in terms of physico-chemical property ranges and use categories. Predictivities of skin sensitization potential and potency, where applicable, were calculated for the LLNA as compared to human data and for the individual test methods compared to both human and LLNA reference data. In addition, various aspects of applicability of the test methods were analyzed. Due to its high level of curation, comprehensiveness, and completeness, we propose our database as a point of reference for the evaluation and development of testing strategies, as done for example in the associated work of Kleinstreuer et al. We encourage the community to use it to meet the challenge of conducting skin sensitization safety assessment without generating new animal data.

Hydrocoin level 3 - Testing methods for sensitivity/uncertainty analysis

International Nuclear Information System (INIS)

Grundfelt, B.; Lindbom, B.; Larsson, A.; Andersson, K.

1991-01-01

The HYDROCOIN study is an international cooperative project for testing groundwater hydrology modelling strategies for performance assessment of nuclear waste disposal. The study was initiated in 1984 by the Swedish Nuclear Power Inspectorate and the technical work was finalised in 1987. The participating organisations are regulatory authorities as well as implementing organisations in 10 countries. The study has been performed at three levels aimed at studying computer code verification, model validation and sensitivity/uncertainty analysis respectively. The results from the first two levels, code verification and model validation, have been published in reports in 1988 and 1990 respectively. This paper focuses on some aspects of the results from Level 3, sensitivity/uncertainty analysis, for which a final report is planned to be published during 1990. For Level 3, seven test cases were defined. Some of these aimed at exploring the uncertainty associated with the modelling results by simply varying parameter values and conceptual assumptions. In other test cases statistical sampling methods were applied. One of the test cases dealt with particle tracking and the uncertainty introduced by this type of post processing. The amount of results available is substantial although unevenly spread over the test cases. It has not been possible to cover all aspects of the results in this paper. Instead, the different methods applied will be illustrated by some typical analyses. 4 figs., 9 refs

Nuclear waste. Which alternatives for method and siting should be accounted for?

International Nuclear Information System (INIS)

2006-06-01

At a seminar in february 2006, KASAM discussed the Swedish legislation concerning how the alternatives for disposal of high-level radioactive wastes should be treated in the application for constructing a repository. Such an application is due in 2008 by the Swedish Nuclear Fuel and Waste Management Co. Some of the important conclusions from the seminar are: The EIS must include a thorough description of the reasoning behind the decisions not to continue investigating alternative methods and sites, and the motives for the decisions for the choices made. The considerations that will be made by the environmental court of law and the regulatory authorities will be marked by a 'court of law perspective' and an 'government authority perspective' resp. The government, on the other hand, has the possibility, and obligation, to look from other points of view, e.g. employment policy and energy policy in its decision to approve a certain type of repository or not. The term 'best possible site' is devoid of meaning without clear definitions and descriptions under what circumstances the terms should be applied. Further clarification is needed on the interaction between stipulations on reports of alternatives in the environmental code and in the legislation in 'Act on nuclear activities'

The fish embryo toxicity test as an animal alternative method in hazard and risk assessment and scientific research

International Nuclear Information System (INIS)

Embry, Michelle R.; Belanger, Scott E.; Braunbeck, Thomas A.; Galay-Burgos, Malyka; Halder, Marlies; Hinton, David E.; Leonard, Marc A.; Lillicrap, Adam; Norberg-King, Teresa; Whale, Graham

2010-01-01

Animal alternatives research has historically focused on human safety assessments and has only recently been extended to environmental testing. This is particularly for those assays that involve the use of fish. A number of alternatives are being pursued by the scientific community including the fish embryo toxicity (FET) test, a proposed replacement alternative to the acute fish test. Discussion of the FET methodology and its application in environmental assessments on a global level was needed. With this emerging issue in mind, the ILSI Health and Environmental Sciences Institute (HESI) and the European Centre for Ecotoxicology and Toxicology of Chemicals (ECETOC) held an International Workshop on the Application of the Fish Embryo Test as an Animal Alternative Method in Hazard and Risk Assessment and Scientific Research in March, 2008. The workshop included approximately 40 scientists and regulators representing government, industry, academia, and non-governmental organizations from North America, Europe, and Asia. The goal was to review the state of the science regarding the investigation of fish embryonic tests, pain and distress in fish, emerging approaches utilizing fish embryos, and the use of fish embryo toxicity test data in various types of environmental assessments (e.g., hazard, risk, effluent, and classification and labeling of chemicals). Some specific key outcomes included agreement that risk assessors need fish data for decision-making, that extending the FET to include eluethereombryos was desirable, that relevant endpoints are being used, and that additional endpoints could facilitate additional uses beyond acute toxicity testing. The FET was, however, not yet considered validated sensu OECD. An important action step will be to provide guidance on how all fish tests can be used to assess chemical hazard and to harmonize the diverse terminology used in test guidelines adopted over the past decades. Use of the FET in context of effluent assessments

The fish embryo toxicity test as an animal alternative method in hazard and risk assessment and scientific research

Energy Technology Data Exchange (ETDEWEB)

Embry, Michelle R., E-mail: membry@ilsi.org [ILSI Health and Environmental Sciences Institute, 1156 15th Street, NW, Suite 200, Washington, DC 20005 (United States); Belanger, Scott E., E-mail: belanger.se@pg.com [Procter and Gamble, Central Product Safety, PO Box 538707, Miami Valley Innovation Center, Cincinnati, OH 45253-8707 (United States); Braunbeck, Thomas A., E-mail: braunbeck@zoo.uni-heidelberg.de [University of Heidelberg, Im Neuenheimer Feld 230, Heidelberg D -69120 (Germany); Galay-Burgos, Malyka, E-mail: malyka.galay-burgos@ecetoc.org [European Centre for Ecotoxicology and Toxicology of Chemicals (ECETOC), 4 Avenue E. Van Nieuwenhuyse B-1160, Brussels (Belgium); Halder, Marlies, E-mail: marlies.halder@jrc.ec.europa.eu [European Commission, Joint Research Centre, Institute for Health and Consumer Protection, In-Vitro Methods Unit TP-580 Ispra 21027 (Italy); Hinton, David E., E-mail: dhinton@duke.edu [Duke University, Nicholas School of the Environment, PO Box 90328, Durham, NC 27708, Unites States (United States); Leonard, Marc A., E-mail: mleonard@rd.loreal.com [L' Oreal Recherche Avancee, Unite d' Ecotoxicologie, 1 av. E. Schueller, 93601 Aulnay sous bois (France); Lillicrap, Adam, E-mail: Adam.lillicrap@niva.no [AstraZeneca, Freshwater Quarry, Brixham TQ5 8BA (United Kingdom); Norberg-King, Teresa, E-mail: norberg-king.teresa@epa.gov [U.S. EPA, Mid-Continent Ecology Division, 6201 Congdon Boulevard, Duluth, MN 55804-1636 (United States); Whale, Graham, E-mail: graham.whale@shell.com [Shell Global Solutions, Analytical Technology, P.O. Box 1, Chester CH1 3SH (United Kingdom)

2010-04-15

Animal alternatives research has historically focused on human safety assessments and has only recently been extended to environmental testing. This is particularly for those assays that involve the use of fish. A number of alternatives are being pursued by the scientific community including the fish embryo toxicity (FET) test, a proposed replacement alternative to the acute fish test. Discussion of the FET methodology and its application in environmental assessments on a global level was needed. With this emerging issue in mind, the ILSI Health and Environmental Sciences Institute (HESI) and the European Centre for Ecotoxicology and Toxicology of Chemicals (ECETOC) held an International Workshop on the Application of the Fish Embryo Test as an Animal Alternative Method in Hazard and Risk Assessment and Scientific Research in March, 2008. The workshop included approximately 40 scientists and regulators representing government, industry, academia, and non-governmental organizations from North America, Europe, and Asia. The goal was to review the state of the science regarding the investigation of fish embryonic tests, pain and distress in fish, emerging approaches utilizing fish embryos, and the use of fish embryo toxicity test data in various types of environmental assessments (e.g., hazard, risk, effluent, and classification and labeling of chemicals). Some specific key outcomes included agreement that risk assessors need fish data for decision-making, that extending the FET to include eluethereombryos was desirable, that relevant endpoints are being used, and that additional endpoints could facilitate additional uses beyond acute toxicity testing. The FET was, however, not yet considered validated sensu OECD. An important action step will be to provide guidance on how all fish tests can be used to assess chemical hazard and to harmonize the diverse terminology used in test guidelines adopted over the past decades. Use of the FET in context of effluent assessments

A simple in chemico method for testing skin sensitizing potential of chemicals using small endogenous molecules.

Science.gov (United States)

Nepal, Mahesh Raj; Shakya, Rajina; Kang, Mi Jeong; Jeong, Tae Cheon

2018-06-01

Among many of the validated methods for testing skin sensitization, direct peptide reactivity assay (DPRA) employs no cells or animals. Although no immune cells are involved in this assay, it reliably predicts the skin sensitization potential of a chemical in chemico. Herein, a new method was developed using endogenous small-molecular-weight compounds, cysteamine and glutathione, rather than synthetic peptides, to differentiate skin sensitizers from non-sensitizers with an accuracy as high as DPRA. The percent depletion of cysteamine and glutathione by test chemicals was measured by an HPLC equipped with a PDA detector. To detect small-size molecules, such as cysteamine and glutathione, a derivatization by 4-(4-dimethylaminophenylazo) benzenesulfonyl chloride (DABS-Cl) was employed prior to the HPLC analysis. Following test method optimization, a cut-off criterion of 7.14% depletion was applied to differentiate skin sensitizers from non-sensitizers in combination of the ratio of 1:25 for cysteamine:test chemical with 1:50 for glutathione:test chemical for the best predictivity among various single or combination conditions. Although overlapping HPLC peaks could not be fully resolved for some test chemicals, high levels of sensitivity (100.0%), specificity (81.8%), and accuracy (93.3%) were obtained for 30 chemicals tested, which were comparable or better than those achieved with DPRA. Copyright © 2018 Elsevier B.V. All rights reserved.

Sensitivity kernels for viscoelastic loading based on adjoint methods

Science.gov (United States)

Al-Attar, David; Tromp, Jeroen

2014-01-01

kernel' Kη determines the linearized sensitivity of J to viscosity perturbations defined with respect to a laterally heterogeneous reference earth model, while the `rate-of-loading kernel' K_{dot{σ }} determines the sensitivity to variations in the time derivative of the surface load. By restricting attention to spherically symmetric viscosity perturbations, we also obtain a `radial viscosity kernel' overline{K}_{η } such that the associated contribution to δJ can be written int _{IS}overline{K}_{η }δ ln η dr, where IS denotes the subset of radii lying in solid regions. In order to illustrate this theory, we describe its numerical implementation in the case of a spherically symmetric earth model using a 1-D spectral element method, and calculate sensitivity kernels for a range of realistic observables.

Prospective memory tasks: a more sensitive method for screening cognitive impairment in ALS?

Directory of Open Access Journals (Sweden)

Ji Ying

2012-11-01

Full Text Available Abstract Background Cognitive change is prevalent in patients with amyotrophic lateral sclerosis (ALS, but still lack a widely accepted and sensitive screening method. In this study, we try to find a sensitive screening battery for detecting subtle cognitive deficits in patients with ALS. Methods Eighty consecutive ALS patients and 57 matched normal controls underwent the Mini-Mental Status Examination (MMSE, the verbal fluency test (VFT, the Stroop Color Word Interference Test (CWT, and the prospective memory (PM tests, including event-based (EBPM and time-based (TBPM. Results The patients did not differ from the controls in the MMSE, the VFT and the CWT. By contrast, statistically significant differences were found in the PM tests (EBPM: P=0.043; TBPM: P Conclusions Prefrontal lobar dysfunction does exist among ALS patients and may spread from the medial to the lateral region. The PM tests seem more sensitive in ALS patients with frontotemporal dysfunction than are the classical cognitive measures.

SENSITIVITY ANALYSIS OF BUILDING STRUCTURES WITHIN THE SCOPE OF ENERGY, ENVIRONMENT AND INVESTMENT

Directory of Open Access Journals (Sweden)

František Kulhánek

2015-10-01

Full Text Available The primary objective of this paper is to prove the feasibility of sensitivity analysis with dominant weight method for structure parts of envelope of buildings inclusive of energy; ecological and financial assessments, and determination of different designs for same structural part via multi-criteria assessment with theoretical example designs ancillary. Multi-criteria assessment (MCA of different structural designs or in other word alternatives aims to find the best available alternative. The application of sensitivity analysis technique in this paper bases on dominant weighting method. In this research, to choose the best thermal insulation design in the case of that more than one projection, simultaneously, criteria of total thickness (T; heat transfer coefficient (U through the cross section; global warming potential (GWP; acid produce (AP; primary energy content (PEI non renewable and cost per m2 (C are investigated for all designs via sensitivity analysis. Three different designs for external wall (over soil which are convenient with regard to globally suggested energy features for passive house design are investigated through the mentioned six projections. By creating a given set of scenarios; depending upon the importance of each criterion, sensitivity analysis is distributed. As conclusion, uncertainty in the output of model is attributed to different sources in the model input. In this manner, determination of the best available design is achieved. The original outlook and the outlook afterwards the sensitivity analysis are visualized, that enables easily to choose the optimum design within the scope of verified components.

Reliability and Sensitivity Analysis for Laminated Composite Plate Using Response Surface Method

International Nuclear Information System (INIS)

Lee, Seokje; Kim, Ingul; Jang, Moonho; Kim, Jaeki; Moon, Jungwon

2013-01-01

Advanced fiber-reinforced laminated composites are widely used in various fields of engineering to reduce weight. The material property of each ply is well known; specifically, it is known that ply is less reliable than metallic materials and very sensitive to the loading direction. Therefore, it is important to consider this uncertainty in the design of laminated composites. In this study, reliability analysis is conducted using Callosum and Meatball interactions for a laminated composite plate for the case in which the tip deflection is the design requirement and the material property is a random variable. Furthermore, the efficiency and accuracy of the approximation method is identified, and a probabilistic sensitivity analysis is conducted. As a result, we can prove the applicability of the advanced design method for the stabilizer of an underwater vehicle

Reliability and Sensitivity Analysis for Laminated Composite Plate Using Response Surface Method

Energy Technology Data Exchange (ETDEWEB)

Lee, Seokje; Kim, Ingul [Chungnam National Univ., Daejeon (Korea, Republic of); Jang, Moonho; Kim, Jaeki; Moon, Jungwon [LIG Nex1, Yongin (Korea, Republic of)

2013-04-15

Advanced fiber-reinforced laminated composites are widely used in various fields of engineering to reduce weight. The material property of each ply is well known; specifically, it is known that ply is less reliable than metallic materials and very sensitive to the loading direction. Therefore, it is important to consider this uncertainty in the design of laminated composites. In this study, reliability analysis is conducted using Callosum and Meatball interactions for a laminated composite plate for the case in which the tip deflection is the design requirement and the material property is a random variable. Furthermore, the efficiency and accuracy of the approximation method is identified, and a probabilistic sensitivity analysis is conducted. As a result, we can prove the applicability of the advanced design method for the stabilizer of an underwater vehicle.

An in vitro human skin test for assessing sensitization potential.

Science.gov (United States)

Ahmed, S S; Wang, X N; Fielding, M; Kerry, A; Dickinson, I; Munuswamy, R; Kimber, I; Dickinson, A M

2016-05-01

Sensitization to chemicals resulting in an allergy is an important health issue. The current gold-standard method for identification and characterization of skin-sensitizing chemicals was the mouse local lymph node assay (LLNA). However, for a number of reasons there has been an increasing imperative to develop alternative approaches to hazard identification that do not require the use of animals. Here we describe a human in-vitro skin explant test for identification of sensitization hazards and the assessment of relative skin sensitizing potency. This method measures histological damage in human skin as a readout of the immune response induced by the test material. Using this approach we have measured responses to 44 chemicals including skin sensitizers, pre/pro-haptens, respiratory sensitizers, non-sensitizing chemicals (including skin-irritants) and previously misclassified compounds. Based on comparisons with the LLNA, the skin explant test gave 95% specificity, 95% sensitivity, 95% concordance with a correlation coefficient of 0.9. The same specificity and sensitivity were achieved for comparison of results with published human sensitization data with a correlation coefficient of 0.91. The test also successfully identified nickel sulphate as a human skin sensitizer, which was misclassified as negative in the LLNA. In addition, sensitizers and non-sensitizers identified as positive or negative by the skin explant test have induced high/low T cell proliferation and IFNγ production, respectively. Collectively, the data suggests the human in-vitro skin explant test could provide the basis for a novel approach for characterization of the sensitizing activity as a first step in the risk assessment process. Copyright © 2015 John Wiley & Sons, Ltd.

Airshed calculation of the sensitivity of pollutant formation to organic compound classes and oxygenates associated with alternative fuels

International Nuclear Information System (INIS)

McNair, L.; Russell, A.; Odman, M.T.

1992-01-01

This study uses a 3-D Eulerian photochemical model and an advanced chemical reaction mechanism to evaluate the sensitivity of pollutant levels to changes in emissions. In particular, the ozone forming potentials of classes of organic compounds are calculated, with particular emphasis on oxygenated organics associated with alternative fuels. Methanol, ethanol, MTBE, alkane and toluene emissions were found to add about one-fifth the ozone (on a carbon mass basis) as alkenes, aldehydes, non-toluene aromatics and ethene. On a per-carbon basis, formaldehyde added about ten times as much ozone as the least reactive organics tested. The results of the trajectory model-based study usually compare well with those found here. The pollution formation potentials can now be used in assessing the relative impact of various exhaust gas compositions

Using the Delphi method to develop nursing-sensitive quality indicators for the NICU.

Science.gov (United States)

Chen, Lin; Huang, Li-Hua; Xing, Mei-Yuan; Feng, Zhi-Xian; Shao, Le-Wen; Zhang, Mei-Yun; Shao, Rong-Ya

2017-02-01

To develop nursing-sensitive quality indicators consistent with current medical practices in Chinese neonatal intensive care units. The development of nursing-sensitive quality indicators has become a top priority in nursing management. To the best of our knowledge, there has been no objective, scientific and sensitive evaluation of the quality of neonatal intensive care unit nursing in China. A modified Delphi technique was used to seek opinions from experts about what should be used and prioritised as indicators of quality care in neonatal intensive care unit nursing. Based on a literature review, we identified 21 indicators of nursing-sensitive quality in the neonatal intensive care unit. Our group of 11 consultants chose 13 indicators to be discussed using the Delphi method. In October and November 2014, 39 neonatal intensive care unit experts in 18 tertiary hospitals spread across six provinces participated in two rounds of Delphi panels. Of the 13 indicators discussed, 11 were identified as indicators of nursing-sensitive quality in the neonatal intensive care unit: rate of nosocomial infections, rate of accidental endotracheal extubation, rate of errors in medication administration, rate of treatment for pain, rate of peripheral venous extravasation, rate of compliance with handwashing techniques, incidence of pressure ulcers, incidence of noise, the bed-to-care ratio, the proportion of nurses with greater than five years neonatal intensive care unit experience and incidence of retinopathy. The 11 neonatal intensive care unit nursing-sensitive indicators identified by the Delphi method integrated with basic Chinese practices provide a basis for nursing management and the monitoring of nursing quality. This study identified nursing-sensitive quality indicators for neonatal intensive care unit care that are suitable for current clinical practice in China. © 2016 John Wiley & Sons Ltd.

Applications of alternating direction methods to the solution of the time-dependent heat conduction equation with source and in transients stage

International Nuclear Information System (INIS)

Gebrin, A.N.

1981-10-01

Various types and also some variants of alternating direction methods, (A.D.M.), were applied to the solution of the time-dependent heat conduction equation, with source, in region with axial symetry. The results shown that some of the variants perform consistently better than the Classical Cranck-Nicolson method. Having in mind a combination of accuracy, ability to support larg time steps and computational efficiency, the 'alternating direction explicit', (A.D.E.) method appears as the best choice, being the 'alternating direction checkerboard', (A.D.C), method the second best. Additional operations like the exponential transformation or the truncation pos-correction don't seem to be worth, excect for some special cases. (Author) [pt

Perturbative methods applied for sensitive coefficients calculations in thermal-hydraulic systems

International Nuclear Information System (INIS)

Andrade Lima, F.R. de

1993-01-01

The differential formalism and the Generalized Perturbation Theory (GPT) are applied to sensitivity analysis of thermal-hydraulics problems related to pressurized water reactor cores. The equations describing the thermal-hydraulic behavior of these reactors cores, used in COBRA-IV-I code, are conveniently written. The importance function related to the response of interest and the sensitivity coefficient of this response with respect to various selected parameters are obtained by using Differential and Generalized Perturbation Theory. The comparison among the results obtained with the application of these perturbative methods and those obtained directly with the model developed in COBRA-IV-I code shows a very good agreement. (author)

EPR method for the detection of sensitization in stainless steels

International Nuclear Information System (INIS)

Clarke, W.L.; Cowan, R.L.

1980-01-01

The overall objective of the program was to improve the reliability of reactor system piping by increasing knowledge of failure causing mechanisms and by enhancing the capability for design evaluation and analysis. Toward the attainment of that objective, a technique has been developed to measure the degree of sensitization quantitatively in thermally treated AISI-304, -304L, -316 and 316L stainless steels. The Electrochemical Potentiokinetic Reactivation (EPR) test was developed because of an industrial need for a rapid, nondestructive, quantitative field test which could be used for assessing sensitization in reactor components. The EPR method consists of developing potentiokinetic curves on a polarized sample obtained by controlled potential sweep from the passive to the active region (reactivation) in a specific electrolyte; details of the test technique have been reported

Perturbative methods for sensitivity calculation in safety problems of nuclear reactors: state-of-the-art

International Nuclear Information System (INIS)

Lima, Fernando R.A.; Lira, Carlos A.B.O.; Gandini, Augusto

1995-01-01

During the last two decades perturbative methods became an efficient tool to perform sensitivity analysis in nuclear reactor safety problems. In this paper, a comparative study taking into account perturbation formalisms (Diferential and Matricial Mthods and generalized Perturbation Theory - GPT) is considered. Then a few number of applications are described to analyze the sensitivity of some functions relavant to thermal hydraulics designs or safety analysis of nuclear reactor cores and steam generators. The behaviours of the nuclear reactor cores and steam generators are simulated, respectively, by the COBRA-IV-I and GEVAP codes. Results of sensitivity calculations have shown a good agreement when compared to those obtained directly by using the mentioned codes. So, a significative computational time safe can be obtained with perturbative methods performing sensitivity analysis in nuclear power plants. (author). 25 refs., 5 tabs

Reducing the ordering temperature of FePt nanoparticles by Cu additive and alternate reduction method

Directory of Open Access Journals (Sweden)

Fang Wang

2017-12-01

Full Text Available (FePt85Cu15 nanoparticles were successfully prepared by alternate reduction of metal salts in aqueous medium. Detailed investigations on the correlation between the magnetic and structural properties of these nanoparticles are presented as a function of annealing temperature. Both the X-ray diffraction patterns and the magnetic hysteresis loop measurements show the existence of L10-FePt phase at a relative low annealing temperature. It is proved that the Cu additive and alternate reduction are very effective methods in reducing the ordering temperature of FePt nanoparticles.

Acoustic rhinometry (AR): An Alternative Method to Image Nasal Airway Geometry

DEFF Research Database (Denmark)

Straszek, Sune; Pedersen, O.F.

  ACOUSTIC RHINOMETRY (AR): AN ALTERNATIVE METHOD TO IMAGE NASAL AIRWAY GEOMETRY.  INTRODUCTION AND BACKGROUND:  In human studies the acoustic reflection technique was first applied to describe the area-distance relationship of the lower airways, but later the acoustic reflection technique appeared...... to be of more use in the description of nasal cavity geometry. Applied to human subjects AR has been applied to monitor the effect of corrective surgery and mucosal effects of pharmacological interventions. In recent years, however, AR has found use also in pharmacological studies in animals ranging in size...

Technical Note: Method of Morris effectively reduces the computational demands of global sensitivity analysis for distributed watershed models

Directory of Open Access Journals (Sweden)

J. D. Herman

2013-07-01

Full Text Available The increase in spatially distributed hydrologic modeling warrants a corresponding increase in diagnostic methods capable of analyzing complex models with large numbers of parameters. Sobol' sensitivity analysis has proven to be a valuable tool for diagnostic analyses of hydrologic models. However, for many spatially distributed models, the Sobol' method requires a prohibitive number of model evaluations to reliably decompose output variance across the full set of parameters. We investigate the potential of the method of Morris, a screening-based sensitivity approach, to provide results sufficiently similar to those of the Sobol' method at a greatly reduced computational expense. The methods are benchmarked on the Hydrology Laboratory Research Distributed Hydrologic Model (HL-RDHM over a six-month period in the Blue River watershed, Oklahoma, USA. The Sobol' method required over six million model evaluations to ensure reliable sensitivity indices, corresponding to more than 30 000 computing hours and roughly 180 gigabytes of storage space. We find that the method of Morris is able to correctly screen the most and least sensitive parameters with 300 times fewer model evaluations, requiring only 100 computing hours and 1 gigabyte of storage space. The method of Morris proves to be a promising diagnostic approach for global sensitivity analysis of highly parameterized, spatially distributed hydrologic models.

Singularity-sensitive gauge-based radar rainfall adjustment methods for urban hydrological applications

Directory of Open Access Journals (Sweden)

L.-P. Wang

2015-09-01

Full Text Available Gauge-based radar rainfall adjustment techniques have been widely used to improve the applicability of radar rainfall estimates to large-scale hydrological modelling. However, their use for urban hydrological applications is limited as they were mostly developed based upon Gaussian approximations and therefore tend to smooth off so-called "singularities" (features of a non-Gaussian field that can be observed in the fine-scale rainfall structure. Overlooking the singularities could be critical, given that their distribution is highly consistent with that of local extreme magnitudes. This deficiency may cause large errors in the subsequent urban hydrological modelling. To address this limitation and improve the applicability of adjustment techniques at urban scales, a method is proposed herein which incorporates a local singularity analysis into existing adjustment techniques and allows the preservation of the singularity structures throughout the adjustment process. In this paper the proposed singularity analysis is incorporated into the Bayesian merging technique and the performance of the resulting singularity-sensitive method is compared with that of the original Bayesian (non singularity-sensitive technique and the commonly used mean field bias adjustment. This test is conducted using as case study four storm events observed in the Portobello catchment (53 km2 (Edinburgh, UK during 2011 and for which radar estimates, dense rain gauge and sewer flow records, as well as a recently calibrated urban drainage model were available. The results suggest that, in general, the proposed singularity-sensitive method can effectively preserve the non-normality in local rainfall structure, while retaining the ability of the original adjustment techniques to generate nearly unbiased estimates. Moreover, the ability of the singularity-sensitive technique to preserve the non-normality in rainfall estimates often leads to better reproduction of the urban

Singularity-sensitive gauge-based radar rainfall adjustment methods for urban hydrological applications

Science.gov (United States)

Wang, L.-P.; Ochoa-Rodríguez, S.; Onof, C.; Willems, P.

2015-09-01

Gauge-based radar rainfall adjustment techniques have been widely used to improve the applicability of radar rainfall estimates to large-scale hydrological modelling. However, their use for urban hydrological applications is limited as they were mostly developed based upon Gaussian approximations and therefore tend to smooth off so-called "singularities" (features of a non-Gaussian field) that can be observed in the fine-scale rainfall structure. Overlooking the singularities could be critical, given that their distribution is highly consistent with that of local extreme magnitudes. This deficiency may cause large errors in the subsequent urban hydrological modelling. To address this limitation and improve the applicability of adjustment techniques at urban scales, a method is proposed herein which incorporates a local singularity analysis into existing adjustment techniques and allows the preservation of the singularity structures throughout the adjustment process. In this paper the proposed singularity analysis is incorporated into the Bayesian merging technique and the performance of the resulting singularity-sensitive method is compared with that of the original Bayesian (non singularity-sensitive) technique and the commonly used mean field bias adjustment. This test is conducted using as case study four storm events observed in the Portobello catchment (53 km2) (Edinburgh, UK) during 2011 and for which radar estimates, dense rain gauge and sewer flow records, as well as a recently calibrated urban drainage model were available. The results suggest that, in general, the proposed singularity-sensitive method can effectively preserve the non-normality in local rainfall structure, while retaining the ability of the original adjustment techniques to generate nearly unbiased estimates. Moreover, the ability of the singularity-sensitive technique to preserve the non-normality in rainfall estimates often leads to better reproduction of the urban drainage system

Increased sensitivity of OSHA method analysis of diacetyl and 2,3-pentanedione in air.

Science.gov (United States)

LeBouf, Ryan; Simmons, Michael

2017-05-01

Gas chromatography/mass spectrometry (GC/MS) operated in selected ion monitoring mode was used to enhance the sensitivity of OSHA Methods 1013/1016 for measuring diacetyl and 2,3-pentanedione in air samples. The original methods use flame ionization detection which cannot achieve the required sensitivity to quantify samples at or below the NIOSH recommended exposure limits (REL: 5 ppb for diacetyl and 9.3 ppb for 2,3-pentanedione) when sampling for both diacetyl and 2,3-pentanedione. OSHA Method 1012 was developed to measure diacetyl at lower levels but requires an electron capture detector, and a sample preparation time of 36 hours. Using GC/MS allows detection of these two alpha-diketones at lower levels than OSHA Method 1012 for diacetyl and OSHA Method 1016 for 2,3-pentanedione. Acetoin and 2,3-hexanedione may also be measured using this technique. Method quantification limits were 1.1 ppb for diacetyl (22% of the REL), 1.1 ppb for 2,3-pentanedione (12% of the REL), 1.1 ppb for 2,3-hexanedione, and 2.1 ppb for acetoin. Average extraction efficiencies above the limit of quantitation were 100% for diacetyl, 92% for 2,3-pentanedione, 89% for 2,3-hexanedione, and 87% for acetoin. Mass spectrometry with OSHA Methods 1013/1016 could be used by analytical laboratories to provide more sensitive and accurate measures of exposure to diacetyl and 2,3-pentanedione.

Application of NIRS coupled with PLS regression as a rapid, non-destructive alternative method for quantification of KBA in Boswellia sacra

Science.gov (United States)

Al-Harrasi, Ahmed; Rehman, Najeeb Ur; Mabood, Fazal; Albroumi, Muhammaed; Ali, Liaqat; Hussain, Javid; Hussain, Hidayat; Csuk, René; Khan, Abdul Latif; Alam, Tanveer; Alameri, Saif

2017-09-01

In the present study, for the first time, NIR spectroscopy coupled with PLS regression as a rapid and alternative method was developed to quantify the amount of Keto-β-Boswellic Acid (KBA) in different plant parts of Boswellia sacra and the resin exudates of the trunk. NIR spectroscopy was used for the measurement of KBA standards and B. sacra samples in absorption mode in the wavelength range from 700-2500 nm. PLS regression model was built from the obtained spectral data using 70% of KBA standards (training set) in the range from 0.1 ppm to 100 ppm. The PLS regression model obtained was having R-square value of 98% with 0.99 corelationship value and having good prediction with RMSEP value 3.2 and correlation of 0.99. It was then used to quantify the amount of KBA in the samples of B. sacra. The results indicated that the MeOH extract of resin has the highest concentration of KBA (0.6%) followed by essential oil (0.1%). However, no KBA was found in the aqueous extract. The MeOH extract of the resin was subjected to column chromatography to get various sub-fractions at different polarity of organic solvents. The sub-fraction at 4% MeOH/CHCl3 (4.1% of KBA) was found to contain the highest percentage of KBA followed by another sub-fraction at 2% MeOH/CHCl3 (2.2% of KBA). The present results also indicated that KBA is only present in the gum-resin of the trunk and not in all parts of the plant. These results were further confirmed through HPLC analysis and therefore it is concluded that NIRS coupled with PLS regression is a rapid and alternate method for quantification of KBA in Boswellia sacra. It is non-destructive, rapid, sensitive and uses simple methods of sample preparation.

Center index method-an alternative for wear measurements with radiostereometry (RSA).

Science.gov (United States)

Dahl, Jon; Figved, Wender; Snorrason, Finnur; Nordsletten, Lars; Röhrl, Stephan M

2013-03-01

Radiostereometry (RSA) is considered to be the most precise and accurate method for wear-measurements in total hip replacement. Post-operative stereoradiographs has so far been necessary for wear measurement. Hence, the use of RSA has been limited to studies planned for RSA measurements. We compared a new RSA method for wear measurements that does not require previous radiographs with conventional RSA. Instead of comparing present stereoradiographs with post-operative ones, we developed a method for calculating the post-operative position of the center of the femoral head on the present examination and using this as the index measurement. We compared this alternative method to conventional RSA in 27 hips in an ongoing RSA study. We found a high degree of agreement between the methods for both mean proximal (1.19 mm vs. 1.14 mm) and mean 3D wear (1.52 mm vs. 1.44 mm) after 10 years. Intraclass correlation coefficients (ICC) were 0.958 and 0.955, respectively (pRSA offers comparable results to conventional RSA measurements. It allows precise wear measurements without previous radiological examinations. Copyright © 2012 Orthopaedic Research Society.

WAG (water-alternating-gas) as a method for petroleum advanced recovering

International Nuclear Information System (INIS)

Campozana, Fernando P.; Mato, Luiz F.

2000-01-01

Water-Alternating-Gas (WAG) injection is an oil recovery method that has been more and more applied worldwide. Oil recovery has been increased up to 20 % (over conventional waterflooding) in field-scale WAG projects. This additional recovery has been attributed to improved sweep and areal efficiency as well as microscopic displacement efficiency. Field results have shown that not only WAG method combines the advantages of gas and water injection but also leads to more stable fronts and better mobility control. Moreover, three-phase flow usually leads to a lower residual oil saturation when compared to that of two-phase flow. In this study, we show some theoretical aspects of WAG as well as some results obtained from numerical simulation of a pilot project to be implemented in Aracas field, Bahia, Brazil. (author)

Alternative method of inservice hydraulic testing of difficult to test pumps

International Nuclear Information System (INIS)

Stockton, N.B.; Shangari, S.

1994-01-01

The pump test codes require that system resistance be varied until the independent variable (either the pump flow rate or differential pressure) equals its reference value. Variance from this fixed reference value is not specifically allowed. However, the design of many systems makes it impractical to set the independent variable to an exact value. Over a limited range of pump operation about the fixed reference value, linear interpolation between two points of pump operation can be used to accurately determine degradation at the reference value without repeating reference test conditions. This paper presents an overview of possible alternatives for hydraulic testing of pumps and a detailed discussion of the linear interpolation method. The approximation error associated with linear interpolation is analyzed. Methods to quantify and minimize approximation error are presented

Don't spin the pen: two alternative methods for second-stage sampling in urban cluster surveys

Directory of Open Access Journals (Sweden)

Rose Angela MC

2007-06-01

Full Text Available Abstract In two-stage cluster surveys, the traditional method used in second-stage sampling (in which the first household in a cluster is selected is time-consuming and may result in biased estimates of the indicator of interest. Firstly, a random direction from the center of the cluster is selected, usually by spinning a pen. The houses along that direction are then counted out to the boundary of the cluster, and one is then selected at random to be the first household surveyed. This process favors households towards the center of the cluster, but it could easily be improved. During a recent meningitis vaccination coverage survey in Maradi, Niger, we compared this method of first household selection to two alternatives in urban zones: 1 using a superimposed grid on the map of the cluster area and randomly selecting an intersection; and 2 drawing the perimeter of the cluster area using a Global Positioning System (GPS and randomly selecting one point within the perimeter. Although we only compared a limited number of clusters using each method, we found the sampling grid method to be the fastest and easiest for field survey teams, although it does require a map of the area. Selecting a random GPS point was also found to be a good method, once adequate training can be provided. Spinning the pen and counting households to the boundary was the most complicated and time-consuming. The two methods tested here represent simpler, quicker and potentially more robust alternatives to spinning the pen for cluster surveys in urban areas. However, in rural areas, these alternatives would favor initial household selection from lower density (or even potentially empty areas. Bearing in mind these limitations, as well as available resources and feasibility, investigators should choose the most appropriate method for their particular survey context.

29 CFR 2520.104-4 - Alternative method of compliance for certain successor pension plans.

Science.gov (United States)

2010-07-01

... pension plans. 2520.104-4 Section 2520.104-4 Labor Regulations Relating to Labor (Continued) EMPLOYEE... certain successor pension plans. (a) General. Under the authority of section 110 of the Act, this section sets forth an alternative method of compliance for certain successor pension plans in which some...

A roadmap for the development of alternative (non-animal) methods for systemic toxicity testing - t4 report*.

Science.gov (United States)

Basketter, David A; Clewell, Harvey; Kimber, Ian; Rossi, Annamaria; Blaauboer, Bas; Burrier, Robert; Daneshian, Mardas; Eskes, Chantra; Goldberg, Alan; Hasiwa, Nina; Hoffmann, Sebastian; Jaworska, Joanna; Knudsen, Thomas B; Landsiedel, Robert; Leist, Marcel; Locke, Paul; Maxwell, Gavin; McKim, James; McVey, Emily A; Ouédraogo, Gladys; Patlewicz, Grace; Pelkonen, Olavi; Roggen, Erwin; Rovida, Costanza; Ruhdel, Irmela; Schwarz, Michael; Schepky, Andreas; Schoeters, Greet; Skinner, Nigel; Trentz, Kerstin; Turner, Marian; Vanparys, Philippe; Yager, James; Zurlo, Joanne; Hartung, Thomas

2012-01-01

Systemic toxicity testing forms the cornerstone for the safety evaluation of substances. Pressures to move from traditional animal models to novel technologies arise from various concerns, including: the need to evaluate large numbers of previously untested chemicals and new products (such as nanoparticles or cell therapies), the limited predictivity of traditional tests for human health effects, duration and costs of current approaches, and animal welfare considerations. The latter holds especially true in the context of the scheduled 2013 marketing ban on cosmetic ingredients tested for systemic toxicity. Based on a major analysis of the status of alternative methods (Adler et al., 2011) and its independent review (Hartung et al., 2011), the present report proposes a roadmap for how to overcome the acknowledged scientific gaps for the full replacement of systemic toxicity testing using animals. Five whitepapers were commissioned addressing toxicokinetics, skin sensitization, repeated-dose toxicity, carcinogenicity, and reproductive toxicity testing. An expert workshop of 35 participants from Europe and the US discussed and refined these whitepapers, which were subsequently compiled to form the present report. By prioritizing the many options to move the field forward, the expert group hopes to advance regulatory science.

New computer-aided diagnosis of dementia using positron emission tomography: brain regional sensitivity-mapping method.

Directory of Open Access Journals (Sweden)

Akihiro Kakimoto

Full Text Available PURPOSE: We devised a new computer-aided diagnosis method to segregate dementia using one estimated index (Total Z score derived from the Brodmann area (BA sensitivity map on the stereotaxic brain atlas. The purpose of this study is to investigate its accuracy to differentiate patients with Alzheimer's disease (AD or mild cognitive impairment (MCI from normal adults (NL. METHODS: We studied 101 adults (NL: 40, AD: 37, MCI: 24 who underwent (18FDG positron emission tomography (PET measurement. We divided NL and AD groups into two categories: a training group with (Category A and a test group without (Category B clinical information. In Category A, we estimated sensitivity by comparing the standard uptake value per BA (SUVR between NL and AD groups. Then, we calculated a summated index (Total Z score by utilizing the sensitivity-distribution maps and each BA z-score to segregate AD patterns. To confirm the validity of this method, we examined the accuracy in Category B. Finally, we applied this method to MCI patients. RESULTS: In Category A, we found that the sensitivity and specificity of differentiation between NL and AD were all 100%. In Category B, those were 100% and 95%, respectively. Furthermore, we found this method attained 88% to differentiate AD-converters from non-converters in MCI group. CONCLUSIONS: The present automated computer-aided evaluation method based on a single estimated index provided good accuracy for differential diagnosis of AD and MCI. This good differentiation power suggests its usefulness not only for dementia diagnosis but also in a longitudinal study.

New Computer-Aided Diagnosis of Dementia Using Positron Emission Tomography: Brain Regional Sensitivity-Mapping Method

Science.gov (United States)

Kakimoto, Akihiro; Kamekawa, Yuichi; Ito, Shigeru; Yoshikawa, Etsuji; Okada, Hiroyuki; Nishizawa, Sadahiko; Minoshima, Satoshi; Ouchi, Yasuomi

2011-01-01

Purpose We devised a new computer-aided diagnosis method to segregate dementia using one estimated index (Total Z score) derived from the Brodmann area (BA) sensitivity map on the stereotaxic brain atlas. The purpose of this study is to investigate its accuracy to differentiate patients with Alzheimer's disease (AD) or mild cognitive impairment (MCI) from normal adults (NL). Methods We studied 101 adults (NL: 40, AD: 37, MCI: 24) who underwent 18FDG positron emission tomography (PET) measurement. We divided NL and AD groups into two categories: a training group with (Category A) and a test group without (Category B) clinical information. In Category A, we estimated sensitivity by comparing the standard uptake value per BA (SUVR) between NL and AD groups. Then, we calculated a summated index (Total Z score) by utilizing the sensitivity-distribution maps and each BA z-score to segregate AD patterns. To confirm the validity of this method, we examined the accuracy in Category B. Finally, we applied this method to MCI patients. Results In Category A, we found that the sensitivity and specificity of differentiation between NL and AD were all 100%. In Category B, those were 100% and 95%, respectively. Furthermore, we found this method attained 88% to differentiate AD-converters from non-converters in MCI group. Conclusions The present automated computer-aided evaluation method based on a single estimated index provided good accuracy for differential diagnosis of AD and MCI. This good differentiation power suggests its usefulness not only for dementia diagnosis but also in a longitudinal study. PMID:21966405

Community sensitization and decision-making for trial participation: a mixed-methods study from The Gambia.

Science.gov (United States)

Dierickx, Susan; O'Neill, Sarah; Gryseels, Charlotte; Immaculate Anyango, Edna; Bannister-Tyrrell, Melanie; Okebe, Joseph; Mwesigwa, Julia; Jaiteh, Fatou; Gerrets, René; Ravinetto, Raffaella; D'Alessandro, Umberto; Peeters Grietens, Koen

2017-08-16

Ensuring individual free and informed decision-making for research participation is challenging. It is thought that preliminarily informing communities through 'community sensitization' procedures may improve individual decision-making. This study set out to assess the relevance of community sensitization for individual decision-making in research participation in rural Gambia. This anthropological mixed-methods study triangulated qualitative methods and quantitative survey methods in the context of an observational study and a clinical trial on malaria carried out by the Medical Research Council Unit Gambia. Although 38.7% of the respondents were present during sensitization sessions, 91.1% of the respondents were inclined to participate in the trial when surveyed after the sensitization and prior to the informed consent process. This difference can be explained by the informal transmission of information within the community after the community sensitization, expectations such as the benefits of participation based on previous research experiences, and the positive reputation of the research institute. Commonly mentioned barriers to participation were blood sampling and the potential disapproval of the household head. Community sensitization is effective in providing first-hand, reliable information to communities as the information is cascaded to those who could not attend the sessions. However, further research is needed to assess how the informal spread of information further shapes people's expectations, how the process engages with existing social relations and hierarchies (e.g. local political power structures; permissions of heads of households) and how this influences or changes individual consent. © 2017 The Authors Developing World Bioethics Published by John Wiley & Sons Ltd.

A new sensitive method for detecting human endogenous (leukocyte) pyrogen.

Science.gov (United States)

Bodel, P; Miller, H

1978-03-01

Endogenous, or leukocyte pyrogen (EP), the mediator of fever, is currently detected by injection of pyrogen-containing supernatants into rabbits. This assay has been of little value in the study of human fever because it required injection of relatively large amounts of pyrogen. We now report that injection of medium containing human EP produces fever in mice. Supernatant from 1 c 10(5) granulocytes, stimulated by phagocytosis of staphylococci and incubated overnight, or 1 x 10(4) monocytes similarly treated, produce clear pyrogenic responses. This method for detecting EP is about 100-fold more sensitive than the rabbit assay, and it appears to be specific for EP. Preliminary studies of EP released by small samples of needle liver biopsies from febrile and afebrile patients suggests that this sensitive assay may be useful for investigations into the mechanisms of clinical fever.

Maggot debridement: an alternative method for debridement.

Science.gov (United States)

Gottrup, Finn; Jørgensen, Bo

2011-01-01

Debridement is an essential component to promote healing in a problem wound. Several techniques are available including maggot debridement therapy (MDT). To describe the efficacy of MDT for treating problem wound especially diabetic foot ulcers. The topic is elucidated from different points of view: the mode of action, when to use, use in a practice, clinical results, and discussing the problem of creating evidence for the clinical effect. Literature and own results demonstrate that MDT is a safe method with few side effects. Maggot debridement therapy is as good as or better than conventional often surgical debridement, is more selective than surgical debridement, decreases time to healing and stay of patients in the ward, and may decrease the risk of major amputations. However, the evidence of these effects of MDT on the highest level is presently lacking. A detailed description of how to use MDT in practice is provided including a visual demonstration in a video. In spite of lacking clinical evidence, MDT clinical experience strongly suggests that this technique is effective and safe. It can be used for most types of problem wounds, but our indication is primarily diabetic foot ulcers, because of its selectivity for debriding necrotic dead tissue. It may be a valuable alternative surgical/sharp debridement.

Lower Growth Temperature Increases Alternative Pathway Capacity and Alternative Oxidase Protein in Tobacco 1

Science.gov (United States)

Vanlerberghe, Greg C.; McIntosh, Lee

1992-01-01

Suspension cells of NT1 tobacco (Nicotiana tabacum L. cv bright yellow) have been used to study the effect of growth temperature on the CN-resistant, salicylhydroxamic acid-sensitive alternative pathway of respiration. Mitochondria isolated from cells maintained at 30°C had a low capacity to oxidize succinate via the alternative pathway, whereas mitochondria isolated from cells 24 h after transfer to 18°C displayed, on average, a 5-fold increase in this capacity (from 7 to 32 nanoatoms oxygen per milligram protein per minute). This represented an increase in alternative pathway capacity from 18 to 45% of the total capacity of electron transport. This increased capacity was lost upon transfer of cells back to 30°C. A monoclonal antibody to the terminal oxidase of the alternative pathway (the alternative oxidase) from Sauromatum guttatum (T.E. Elthon, R.L. Nickels, L. McIntosh [1989] Plant Physiology 89: 1311-1317) recognized a 35-kilodalton mitochondrial protein in tobacco. There was an excellent correlation between the capacity of the alternative path in isolated tobacco mitochondria and the levels of this 35-kilodalton alternative oxidase protein. Cycloheximide could inhibit both the increased level of the 35-kilodalton alternative oxidase protein and the increased alternative pathway capacity normally seen upon transfer to 18°C. We conclude that transfer of tobacco cells to the lower temperature increases the capacity of the alternative pathway due, at least in part, to de novo synthesis of the 35-kilodalton alternative oxidase protein. Images Figure 3 Figure 4 PMID:16652932

Evaluation of SKB/Posiva's report on the horizontal alternative of the KBS-3 method

International Nuclear Information System (INIS)

Apted, Michael J.; Bennet, David G.; Saario, Timtetr; Savage, David

2009-10-01

The KBS-3 method, based on multiple barriers, is the proposed spent fuel disposal method both in Sweden and Finland. The method has two design alternatives: the vertical (KBS-3V) and the horizontal (KBS-3H). In the KBS-3H concept, copper canisters loaded with spen nuclear fuel are encased in a compacted bentonite buffer with an outer supporting supercontainer composed of a mild steel basket, and the entire supercontainer is emplaced horizontally in long emplacement drifts. SKB and Posiva have conducted a joint research, development and demonstration (RDandD) programme in 2002-2007 with the overall aim of establishing whether the KBS-3H represents a feasible alternative to the reference alternative KBS-3V. The objectives have been to demonstrate that the horizontal deposition alternative is technically feasible and that it fulfils the same long-term safety requirement as the KBS-3V. Swedish Radiation Safety Authority (SSM) considers that it is a proper time to evaluate the work carried by SKB and Posiva when this period of joint research is ended and a relatively complete set of reporting is available. SSM therefore required its external expert group BRITE (the Barrier Review, Integration, Tracking and Evaluation) to evaluate the reporting. The aims of the evaluation are to investigate the differences between the horizontal and vertical design alternatives with respect to: Completeness: has SKB/Posiva identified the full set of key topics, and if not, what additional specific key topics should be evaluated; Depth-of-treatment: has SKB/Posiva analysed the key topics in sufficient depth, and if not, on what specific aspects in more detailed consideration required; Status of information: has SKB/ Posiva provided enough information on the current status of knowledge and uncertainties that impact the understanding of each key topic, and if not, what further information should be cited; Feasibility and practicality: for key issues related to the fabrication and

Radiological consequence evaluation of DBAs with alternative source term method for a Chinese PWR

International Nuclear Information System (INIS)

Li, J.X.; Cao, X.W.; Tong, L.L.; Huang, G.F.

2012-01-01

Highlights: ► Radiological consequence evaluation of DBAs with alternative source term method for a Chinese 900 MWe PWR has been investigated. ► Six typical DBA sequences are analyzed. ► The doses of control room, EAB and outer boundary of LPZ are acceptable. ► The differences between AST method and TID-14844 method are investigated. - Abstract: Since a large amount of fission products may releases into the environment, during the accident progression in nuclear power plants (NPPs), which is a potential hazard to public risk, the radiological consequence should be evaluated for alleviating the hazard. In most Chinese NPPs the method of TID-14844, in which the whole body and thyroid dose criteria is employed as dose criteria, is currently adopted to evaluate the radiological consequences for design-basis accidents (DBAs), but, due to the total effective dose equivalent is employed as dose criteria in alternative radiological source terms (AST) method, it is necessary to evaluate the radiological consequences for DBAs with AST method and to discuss the difference between two methods. By using an integral safety analysis code, an analytical model of the 900 MWe pressurized water reactor (PWR) is built and the radiological consequences in DBAs at control room (CR), exclusion area boundary (EAB), low population zone (LPZ) are analyzed, which includes LOCA and non-LOCA DBAs, such as fuel handling accident (FHA), rod ejection accident (REA), main steam line break (MSLB), steam generator tube rupture (SGTR), locked rotor accident (LRA) by using the guidance of the RG 1.183. The results show that the doses in CR, EAB and LPZ are acceptable compared with dose criteria in RG 1.183 and the differences between AST method and TID-14844 method are also discussed.

Alternative of raw material’s suppliers using TOPSIS method in chicken slaughterhouse industry

Science.gov (United States)

Sari, R. M.; Rizkya, I.; Syahputri, K.; Anizar; Siregar, I.

2018-02-01

Chicken slaughterhouse industry is one of the fastest growing industries that depends on the freshness of raw materials. The raw materials quality arrive at the company depends heavily on the suppliers. Fresh chicken and frozen chicken meat are the main raw materials for this industry. Problems occurred by the suppliers are catering the amount of raw material needs that are not appropriate and also delay during delivery process. This condition causes disruption of the production process in the company. Therefore, it is necessary to determine the best suppliers to supply the main raw materials of fresh and frozen chicken meat on the slaughterhouse chicken industry. This study analyze the supplier’s capability by using TOPSIS method. This method use to find out the best supplier. The TOPSIS method is performed using the principle that chosen alternative must have the shortest distance from the positive solution and furthest from the ideal solution of the geometric point by using the Euclidean distance to determine the relative proximity of the optimum solution alternative. TOPSIS method found the rank of best supplier’s order is supplier A followed by supplier D, supplier B, supplier C, supplier E, supplier F, and supplier G. Based on the rank order obtained from each company, it will assist the company in prioritizing the order to the supplier with the best rank. Total supply from All suppliers are 885,994 kg per month. Based on the results of research, the top five suppliers have been sufficient to meet the needs of the company.

Application of perturbation methods and sensitivity analysis to water hammer problems in hydraulic networks

International Nuclear Information System (INIS)

Balino, Jorge L.; Larreteguy, Axel E.; Andrade Lima, Fernando R.

1995-01-01

The differential method was applied to the sensitivity analysis for water hammer problems in hydraulic networks. Starting from the classical water hammer equations in a single-phase liquid with friction, the state vector comprising the piezometric head and the velocity was defined. Applying the differential method the adjoint operator, the adjoint equations with the general form of their boundary conditions, and the general form of the bilinear concomitant were calculated. The discretized adjoint equations and the corresponding boundary conditions were programmed and solved by using the so called method of characteristics. As an example, a constant-level tank connected through a pipe to a valve discharging to atmosphere was considered. The bilinear concomitant was calculated for this particular case. The corresponding sensitivity coefficients due to the variation of different parameters by using both the differential method and the response surface generated by the computer code WHAT were also calculated. The results obtained with these methods show excellent agreement. (author). 11 refs, 2 figs, 2 tabs

Sensitivity theory for general non-linear algebraic equations with constraints

International Nuclear Information System (INIS)

Oblow, E.M.

1977-04-01

Sensitivity theory has been developed to a high state of sophistication for applications involving solutions of the linear Boltzmann equation or approximations to it. The success of this theory in the field of radiation transport has prompted study of possible extensions of the method to more general systems of non-linear equations. Initial work in the U.S. and in Europe on the reactor fuel cycle shows that the sensitivity methodology works equally well for those non-linear problems studied to date. The general non-linear theory for algebraic equations is summarized and applied to a class of problems whose solutions are characterized by constrained extrema. Such equations form the basis of much work on energy systems modelling and the econometrics of power production and distribution. It is valuable to have a sensitivity theory available for these problem areas since it is difficult to repeatedly solve complex non-linear equations to find out the effects of alternative input assumptions or the uncertainties associated with predictions of system behavior. The sensitivity theory for a linear system of algebraic equations with constraints which can be solved using linear programming techniques is discussed. The role of the constraints in simplifying the problem so that sensitivity methodology can be applied is highlighted. The general non-linear method is summarized and applied to a non-linear programming problem in particular. Conclusions are drawn in about the applicability of the method for practical problems

Outfall as a Suitable Alternative for Disposal of Municipal Wastewater in Coastal Areas

Directory of Open Access Journals (Sweden)

Afshin Takdastan

2005-11-01

Full Text Available Disposal of raw municipal wastewater or effluent of preliminary treatment into the sea and ocean is economically more accepted and technically more efficient than secondary treatment. In this method, the wastewater disposed at the bottom of the sea in some points from diffuser. Nowadays, lots of researchers select outfall as a suitable alternative treatment method for coastal cities. The goal of this paper was to introduce the outfall as a wastewater treatment method and its design criteria considering different characteristics of the sea such as salinity, density, temperature, stratification etc. In addition, stagnant sea and thermal stratification is reviewed. In this paper the latest information were reviewed. In this alternative the wastewater treated under dilution, mixing and natural conditions. Moreover, sensitive coastal point are preserved from different wastewater pollutants. Usually, there is no limitation regarding discharge of coliform, DO, BOD, and nutrient concentrations in initial mixing zoom. The parameters such as thermal stratification, salinity stratification, density stratification, marine flows influence design of outfall.

76 FR 50221 - International Workshop on Alternative Methods for Human and Veterinary Rabies Vaccine Testing...

Science.gov (United States)

2011-08-12

... and Veterinary Rabies Vaccine Testing: State of the Science and Planning the Way Forward AGENCY... (NICEATM) announces an ``International Workshop on Alternative Methods for Human and Veterinary Rabies... rabies vaccine potency testing, and to develop an implementation strategy to achieve global acceptance...

29 CFR 4010.12 - Alternative method of compliance for certain sponsors of multiple employer plans.

Science.gov (United States)

2010-07-01

... BENEFIT GUARANTY CORPORATION CERTAIN REPORTING AND DISCLOSURE REQUIREMENTS ANNUAL FINANCIAL AND ACTUARIAL INFORMATION REPORTING § 4010.12 Alternative method of compliance for certain sponsors of multiple employer... part for an information year if any contributing sponsor of the multiple employer plan provides a...

Deterministic sensitivity analysis of two-phase flow systems: forward and adjoint methods. Final report

International Nuclear Information System (INIS)

Cacuci, D.G.

1984-07-01

This report presents a self-contained mathematical formalism for deterministic sensitivity analysis of two-phase flow systems, a detailed application to sensitivity analysis of the homogeneous equilibrium model of two-phase flow, and a representative application to sensitivity analysis of a model (simulating pump-trip-type accidents in BWRs) where a transition between single phase and two phase occurs. The rigor and generality of this sensitivity analysis formalism stem from the use of Gateaux (G-) differentials. This report highlights the major aspects of deterministic (forward and adjoint) sensitivity analysis, including derivation of the forward sensitivity equations, derivation of sensitivity expressions in terms of adjoint functions, explicit construction of the adjoint system satisfied by these adjoint functions, determination of the characteristics of this adjoint system, and demonstration that these characteristics are the same as those of the original quasilinear two-phase flow equations. This proves that whenever the original two-phase flow problem is solvable, the adjoint system is also solvable and, in principle, the same numerical methods can be used to solve both the original and adjoint equations

Highly sensitive luminescence method of scandium determination in the products of metallurgical reprocessing

International Nuclear Information System (INIS)

Matveets, M.A.; Akhmetova, S.D.

1988-01-01

Highly sensitive reaction of scandium with 1,10-phenanthroline and eosin is used for the development of luminescence method of its determination in metallurgical products. The effect of interfering elements is eliminated by scandium extraction with monocarboxylic acids. The method permits to determine scandium content from 5 x 10 -5 % (Sr 0.15 - 0.25)

Risk Sensitivity, Independence of Irrelevant Alternatives and Continuity of Bargaining Solutions

NARCIS (Netherlands)

M.B.M. de Koster (René); H.J.M. Peters (Hans); S.H. Tijs; P.P. Wakker (Peter)

1983-01-01

textabstractBargaining solutions are considered which have the following four properties: individual rationality, Pareto optimality, independence of equivalent utility representations, and independence of irrelevant alternatives. A main result of this paper is a simple proof of the fact that all

Sensitive spectrophotometric methods for determination of some organophosphorus pesticides in vegetable samples

Directory of Open Access Journals (Sweden)

MAGDA A. AKL

2010-03-01

Full Text Available Three rapid, simple, reproducible and sensitive spectrophotometric methods (A, B and C are described for the determination of two organophosphorus pesticides, (malathion and dimethoate in formulations and vegetable samples. The methods A and B involve the addition of an excess of Ce4+ into sulphuric acid medium and the determination of the unreacted oxidant by decreasing the red color of chromotrope 2R (C2R at a suitable lmax = 528 nm for method A, or a decrease in the orange pink color of rhodamine 6G (Rh6G at a suitable lmax = = 525 nm. The method C is based on the oxidation of malathion or dimethoate with the slight excess of N-bromosuccinimide (NBS and the determination of unreacted oxidant by reacting it with amaranth dye (AM in hydrochloric acid medium at a suitable lmax = 520 nm. A regression analysis of Beer-Lambert plots showed a good correlation in the concentration range of 0.1-4.2 μg mL−1. The apparent molar absorptivity, Sandell sensitivity, the detection and quantification limits were calculated. For more accurate analysis, Ringbom optimum concentration ranges are 0.25-4.0 μg mL−1. The developed methods were successfully applied to the determination of malathion, and dimethoate in their formulations and environmental vegetable samples.

Sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of advective release from waste packages under dripping fractures

International Nuclear Information System (INIS)

Lee, J.H.; Atkins, J.E.; McNeish, J.A.; Vallikat, V.

1996-01-01

Simulations were conducted to analyze the sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of the advective release from waste packages under dripping fractures. The first conceptual model assumed that dripping water directly contacts the waste form inside the 'failed' waste package, and radionuclides are released from the EBS by advection. The second conceptual model assumed that dripping water is diverted around the 'failed' waste package (because of the presence of corrosion products plugging the perforations) and dripping water is prevented from directly contacting the waste form. In the second model, radionuclides were assumed to transport through the perforations by diffusion, and, once outside the waste package, to be released from the EBS by advection. The second model was to incorporate more realism into the EBS release calculations. For the case with the second EBS release model, most radionuclides had significantly lower peak EBS release rates (from at least one to several orders of magnitude) than with the first EBS release model. The impacts of the alternative EBS release models were greater for the radionuclides with a low solubility (or solubility-limited radionuclides) than for the radionuclides with a high solubility (or waste form dissolution-limited radionuclides). The analyses indicated that the EBS release model representing advection through a 'failed' waste package (the first EBS release model) may be too conservative in predicting the EBS performance. One major implication from this sensitivity study was that a 'failed' waste package container with multiple perforations may still be able to perform effectively as an important barrier to radionuclide release. (author)

An UPLC-MS/MS method for highly sensitive high-throughput analysis of phytohormones in plant tissues

Directory of Open Access Journals (Sweden)

Balcke Gerd Ulrich

2012-11-01

Full Text Available Abstract Background Phytohormones are the key metabolites participating in the regulation of multiple functions of plant organism. Among them, jasmonates, as well as abscisic and salicylic acids are responsible for triggering and modulating plant reactions targeted against pathogens and herbivores, as well as resistance to abiotic stress (drought, UV-irradiation and mechanical wounding. These factors induce dramatic changes in phytohormone biosynthesis and transport leading to rapid local and systemic stress responses. Understanding of underlying mechanisms is of principle interest for scientists working in various areas of plant biology. However, highly sensitive, precise and high-throughput methods for quantification of these phytohormones in small samples of plant tissues are still missing. Results Here we present an LC-MS/MS method for fast and highly sensitive determination of jasmonates, abscisic and salicylic acids. A single-step sample preparation procedure based on mixed-mode solid phase extraction was efficiently combined with essential improvements in mobile phase composition yielding higher efficiency of chromatographic separation and MS-sensitivity. This strategy resulted in dramatic increase in overall sensitivity, allowing successful determination of phytohormones in small (less than 50 mg of fresh weight tissue samples. The method was completely validated in terms of analyte recovery, sensitivity, linearity and precision. Additionally, it was cross-validated with a well-established GC-MS-based procedure and its applicability to a variety of plant species and organs was verified. Conclusion The method can be applied for the analyses of target phytohormones in small tissue samples obtained from any plant species and/or plant part relying on any commercially available (even less sensitive tandem mass spectrometry instrumentation.

Short ensembles: An Efficient Method for Discerning Climate-relevant Sensitivities in Atmospheric General Circulation Models

Energy Technology Data Exchange (ETDEWEB)

Wan, Hui; Rasch, Philip J.; Zhang, Kai; Qian, Yun; Yan, Huiping; Zhao, Chun

2014-09-08

This paper explores the feasibility of an experimentation strategy for investigating sensitivities in fast components of atmospheric general circulation models. The basic idea is to replace the traditional serial-in-time long-term climate integrations by representative ensembles of shorter simulations. The key advantage of the proposed method lies in its efficiency: since fewer days of simulation are needed, the computational cost is less, and because individual realizations are independent and can be integrated simultaneously, the new dimension of parallelism can dramatically reduce the turnaround time in benchmark tests, sensitivities studies, and model tuning exercises. The strategy is not appropriate for exploring sensitivity of all model features, but it is very effective in many situations. Two examples are presented using the Community Atmosphere Model version 5. The first example demonstrates that the method is capable of characterizing the model cloud and precipitation sensitivity to time step length. A nudging technique is also applied to an additional set of simulations to help understand the contribution of physics-dynamics interaction to the detected time step sensitivity. In the second example, multiple empirical parameters related to cloud microphysics and aerosol lifecycle are perturbed simultaneously in order to explore which parameters have the largest impact on the simulated global mean top-of-atmosphere radiation balance. Results show that in both examples, short ensembles are able to correctly reproduce the main signals of model sensitivities revealed by traditional long-term climate simulations for fast processes in the climate system. The efficiency of the ensemble method makes it particularly useful for the development of high-resolution, costly and complex climate models.

Enhancing the open-circuit voltage of dye-sensitized solar cells: coadsorbents and alternative redox couples[Dissertation 4066

Energy Technology Data Exchange (ETDEWEB)

Zhang, Z.

2008-04-15

In February 2008, the oil price easily exceeded US dollar 100 per barrel due to the weak US dollar and the imbalance between the increasing demands and deficient supplies. People are paying more and more attention to seek for alternative energy sources that would suffice the modern society in the following high-oil-price era. The work in this thesis is associated with some fundamental research in one of the solutions to the energy shortage, photovoltaics. Particularly, the dye-sensitized solar cell was taken as the system where the effects of coadsorbents and alternative couples to the classic iodide/iodine redox were studied and rationalized. The first chapter was a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the dye cell. In Chapter 2, we specified all the experimental issues, including the chemicals, materials, film preparation, characterization techniques and data analysis. A short part was also dedicated to the basics of the photovoltaics. We studied the electronic effect of the scattering particles in our devices in Chapter 3. These particles were of 400 nm in diameter and always put on top of the nanotransparent layer to increase the light harvesting of the devices. It was found that the particles gave a small dark current but under illumination, they made a significant contribution to the total photocurrent. Photovoltage and photocurrent transient decay measurements performed under bias illumination showed that the density of electronic states of the light scattering layer was two times smaller than that of a transparent nanoparticle layer. From Chapter 4 to Chapter 7, we systematically studied the function of the coadsorbents. Application of an {omega}-guannidino carboxylic acid was found to increase the open-circuit voltage of the device by 50 mV. Coadsorbents with similar structures were then employed with an amphiphilic ruthenium sensitizer, Z-907, to scrutinize

Substantiation of selection method of preferred alternative of belt conveyor drive systems on the basis of the analytic hierarchy process

Directory of Open Access Journals (Sweden)

Goncharov K.A.

2016-06-01

Full Text Available This paper provides substantiation of selection method of preferred alternative of belt conveyor drive systems on the basis of the analytic hierarchy process. Conditions for the correct application of the proposed method in the selection process of preferred alternative of technical objects were worked out. The set of criteria of system effectiveness evalua-tion and the corresponding hierarchical structure in accordance with the developed conditions was proposed.

Analysis of alternative splicing events for cancer diagnosis using a multiplexing nanophotonic biosensor.

Science.gov (United States)

Huertas, César S; Domínguez-Zotes, Santos; Lechuga, Laura M

2017-01-25

Personalized medicine is a promising tool not only for prevention, screening and development of more efficient treatment strategies, but also for diminishing the side effects caused by current therapies. Deciphering gene regulation pathways provides a reliable prognostic analysis to elucidate the origin of grave diseases and facilitate the selection of the most adequate treatment for each individual. Alternative splicing of mRNA precursors is one of these gene regulation pathways and enables cells to generate different protein outputs from the same gene depending on their developmental or homeostatic status. Its deregulation is strongly linked to disease onset and progression constituting a relevant and innovative class of biomarker. Herein we report a highly selective and sensitive nanophotonic biosensor based on the direct monitoring of the aberrant alternative splicing of Fas gene. Unlike conventional methods, the nanobiosensor performs a real-time detection of the specific isoforms in the fM-pM range without any cDNA synthesis or PCR amplification requirements. The nanobiosensor has been proven isoform-specific with no crosshybridization, greatly minimizing detection biases. The demonstrated high sensitivity and specificity make our nanobiosensor ideal for examining significant tumor-associated expression shifts of alternatively spliced isoforms for the early and accurate theranostics of cancer.

Synthesis of SnS nanoparticles by SILAR method for quantum dot-sensitized solar cells.

Science.gov (United States)

Tsukigase, Hiroki; Suzuki, Yoshikazu; Berger, Marie-Hélène; Sagawa, Takashi; Yoshikawa, Susumu

2011-03-01

SnS-sensitized TiO2 electrodes were applied in quantum dot-sensitized solar cells (QDSSCs) which are environmentally more favorable than conventional Cd or Pb-chalcogenide-sensitized electrodes. SnS nanoparticles were well-distributed over the surface of TiO2 nanoparticles by the successive ionic layer adsorption and reaction (SILAR) method. Deposited SnS nanoparticles had diameter about 3 nm. Under AM1.5 irradiation with 100 mW/cm2 light intensity (at 1 sun), the energy conversion efficiency of obtained cells reached a value of 0.21% (0.25 cm2) at SILAR coating cycles of 5. In addition, the photovoltaic performance was improved by additional ZnS coating on the surface of SnS-sensitized TiO2 electrodes.

Alternative method for intramuscular fat analysis using common laboratory equipment.

Science.gov (United States)

Segura, J; Calvo, L; Óvilo, C; González-Bulnes, A; Olivares, A; Cambero, M I; López-Bote, C J

2015-05-01

A procedure to quantify intramuscular fat was developed using common inexpensive laboratory equipment. Three homogenization methods of lyophilized muscle samples (Ball-mill, Grinder and Mortar) and two extraction methods (Ball-mill or Vortex) were used in turkey meat and pork. Two-hundred mg of lyophilized and homogenized samples were accurately weighed and mixed with 1.5 mL of dichloromethane-methanol (8:2) and shaken either in a Mixer Mill (MM400, Retsch Technology) or in a Vortex. The final mixture was separated by centrifugation. Solvent was evaporated under a nitrogen stream and lipid content was gravimetrically determined. Besides, it was checked that the fatty acid profile was not altered by the protocol used. Moreover, the analysis of 4 replicas from the same sample showed different variation coefficients (16-29%) for the new procedures proposed over a wide range of IMF content. The combination of Grinder and Vortex methodologies can be proposed as a simple and inexpensive alternative to previous ones. Copyright © 2015. Published by Elsevier Ltd.

Short ensembles: an efficient method for discerning climate-relevant sensitivities in atmospheric general circulation models

Directory of Open Access Journals (Sweden)

H. Wan

2014-09-01

Full Text Available This paper explores the feasibility of an experimentation strategy for investigating sensitivities in fast components of atmospheric general circulation models. The basic idea is to replace the traditional serial-in-time long-term climate integrations by representative ensembles of shorter simulations. The key advantage of the proposed method lies in its efficiency: since fewer days of simulation are needed, the computational cost is less, and because individual realizations are independent and can be integrated simultaneously, the new dimension of parallelism can dramatically reduce the turnaround time in benchmark tests, sensitivities studies, and model tuning exercises. The strategy is not appropriate for exploring sensitivity of all model features, but it is very effective in many situations. Two examples are presented using the Community Atmosphere Model, version 5. In the first example, the method is used to characterize sensitivities of the simulated clouds to time-step length. Results show that 3-day ensembles of 20 to 50 members are sufficient to reproduce the main signals revealed by traditional 5-year simulations. A nudging technique is applied to an additional set of simulations to help understand the contribution of physics–dynamics interaction to the detected time-step sensitivity. In the second example, multiple empirical parameters related to cloud microphysics and aerosol life cycle are perturbed simultaneously in order to find out which parameters have the largest impact on the simulated global mean top-of-atmosphere radiation balance. It turns out that 12-member ensembles of 10-day simulations are able to reveal the same sensitivities as seen in 4-year simulations performed in a previous study. In both cases, the ensemble method reduces the total computational time by a factor of about 15, and the turnaround time by a factor of several hundred. The efficiency of the method makes it particularly useful for the development of

Evaluation of alternative methods for coronary calcium scoring in multi-detector-row computed tomography

International Nuclear Information System (INIS)

Serafin, Z.; Lasek, W.; Laskowska, K.; Marzec, M.

2005-01-01

Determining coronary artery calcifications is one of the methods of coronary heart disease screening. However, the traditional Agatston Calcium Score (CS) shows low interexamination reproducibility. The aim of this study was to evaluate the interscan variability coefficients of calcium measures based on three modifications of the original Agatston equation. Fifty adults (37 men and 13 women; mean age 46.2 ± 9.2 years) were included in the study. Each patient was examined with two consecutive, prospectively electrocardiographically triggered, multi-detector-row CT acquisitions to detect and quantify coronary artery calcifications. CS was calculated according to the method by Agatston et al. Alternative scores were calculated using a continuous weighting factor (CS-CM), the average lesion attenuation value (CS-SA), or both (CS-CA). The mean and median interscan percent variabilities of the methods were evaluated using nonparametric analysis of variance. In the 50 patients, 1315 calcified lesions were found. The alternative scores correlated well with CS (for CS vs. CS-SA, CS-CM, and CS-CA, r = 0.990, 0.840, and 0.946, respectively, P < 0.0001). The mean and median percent variabilities did not differ significantly among the methods tested (P = 0.370). For CS, CS-SA, CS-CM, and CS-CA the mean variabilities were 13.24%, 13.36%, 16.00%, and 13.62%, respectively. Except for CS-CM, the methods showed similar distributions of variability vs. score on Bland and Altman plots. None of the tested modifications of the Agatston method brought improvement in the interscan reproducibility of coronary calcium scoring. In our opinion, a significant reduction in variability may be achieved by a standardization of image acquisition and reconstruction. (author)

The economic efficiency impacts of alternatives for revenue reconciliation

International Nuclear Information System (INIS)

Kim, B.H.; Baughman, M.L.

1997-01-01

About a dozen electric utilities in the US offer rates that possess real-time characteristics. In these implementations the real-time prices are updated at half-hourly intervals and in no case are the prices spatially differentiated. The implemented rates are based upon marginal generating costs with markups to account for system transmission and distribution costs or other revenue reconciliation needs. This paper analyzes how great is the impact of alternative price markup methods on measures of social welfare and the time pattern of real-time prices. A case study and sensitivity results are also presented

Alternative parameter determination methods for a PMSG

DEFF Research Database (Denmark)

Kalogiannis, Theodoros; Malz, Elena; Llano, Enrique Muller

2014-01-01

standards. In the other hand a new approach for an alternative stator inductance and inertia measurement is analysed. More precisely, the former is obtained through laboratory work based on the locked rotor test, and the latter through a CAD software based on a 3D model. In order to assess and validate...

Simplified methods of evaluating colonies for levels of Varroa Sensitive Hygiene (VSH)

Science.gov (United States)

Varroa sensitive hygiene (VSH) is a trait of honey bees, Apis mellifera, that supports resistance to varroa mites, Varroa destructor. Components of VSH were evaluated to identify simple methods for selection of the trait. Varroa mite population growth was measured in colonies with variable levels of...

State of the art on alternative methods to animal testing from an industrial point of view: ready for regulation?

Science.gov (United States)

Ashton, Rachel; De Wever, Bart; Fuchs, Horst W; Gaca, Marianna; Hill, Erin; Krul, Cyrille; Poth, Albrecht; Roggen, Erwin L

2014-01-01

Despite changing attitudes towards animal testing and current legislation to protect experimental animals, the rate of animal experiments seems to have changed little in recent years. On May 15-16, 2013, the In Vitro Testing Industrial Platform (IVTIP) held an open meeting to discuss the state of the art in alternative methods, how companies have, can, and will need to adapt and what drives and hinders regulatory acceptance and use. Several key messages arose from the meeting. First, industry and regulatory bodies should not wait for complete suites of alternative tests to become available, but should begin working with methods available right now (e.g., mining of existing animal data to direct future studies, implementation of alternative tests wherever scientifically valid rather than continuing to rely on animal tests) in non-animal and animal integrated strategies to reduce the numbers of animals tested. Sharing of information (communication), harmonization and standardization (coordination), commitment and collaboration are all required to improve the quality and speed of validation, acceptance, and implementation of tests. Finally, we consider how alternative methods can be used in research and development before formal implementation in regulations. Here we present the conclusions on what can be done already and suggest some solutions and strategies for the future.

Discussion of ALTERNATIVE systems for industrial radiography using X-ray films

International Nuclear Information System (INIS)

Vaessen B.; Perdieus, P.; Proegler, H.

1995-01-01

Industrial radiography using X-ray films is an established method of NDE. In the last few years, ''novel developments'' have been put on the market as ''alternatives'' to conventional radiography, as e.g. fluorescent screen/film systems, cost-saving films, wide-latitude films, and storage phosphor films. AGFA as a market leader in the sector of X-ray films for industrial radiography has been testing these alternatives, taking into account image quality, sensitivity, handling in terms of portability, reliability, and the essential functions for NDE: (1) Detection of X-radiation; (2) conversion to optical image; (3) evaluation and validation; (4) documentation and archivation. The advantages and drawbacks, the information transfer capabilities, and the performance from the applications point of view are discussed primarily for fluorescent screen/film systems and storage phophor systems. (orig./MM) [de

A fluorescence high throughput screening method for the detection of reactive electrophiles as potential skin sensitizers

Science.gov (United States)

Skin sensitization is an important toxicological end-point in the risk assessment of chemical allergens. Because of the complexity of the biological mechanisms associated with skin sensitization integrated approaches combining different chemical, biological and in silico methods are recommended to r...

26 CFR 20.2032-1 - Alternate valuation.

Science.gov (United States)

2010-04-01

... alternate valuation method under section 2032, the property included in the decedent's gross estate on the..., the alternate valuation method applies to all property included in the gross estate and cannot be... elects the alternate valuation method under section 2432, all property interests existing at the date of...

Local lymph node assay (LLNA) for detection of sensitization capacity of chemicals.

Science.gov (United States)

Gerberick, G Frank; Ryan, Cindy A; Dearman, Rebecca J; Kimber, Ian

2007-01-01

The local lymph node assay (LLNA) is a murine model developed to evaluate the skin sensitization potential of chemicals. The LLNA is an alternative approach to traditional guinea pig methods and in comparison provides important animal welfare benefits. The assay relies on measurement of events induced during the induction phase of skin sensitization, specifically lymphocyte proliferation in the draining lymph nodes which is a hallmark of a skin sensitization response. Since its introduction the LLNA has been the subject of extensive evaluation on a national and international scale, and has been successfully validated and incorporated worldwide into regulatory guidelines. Experience gained in recent years has demonstrated that adherence to published procedures and guidelines for the LLNA (e.g., with respect to dose and vehicle selection) is critical for the successful conduct and eventual interpretation of the data. In addition to providing a robust method for skin sensitization hazard identification, the LLNA has proven very useful in assessing the skin sensitizing potency of test chemicals, and this has provided invaluable information to risk assessors. The primary method to make comparisons of the relative potency of chemical sensitizers is to use linear interpolation to estimate the concentration of chemical required to induce a stimulation index of three relative to concurrent vehicle-treated controls (EC3). In certain situations where there are available less than optimal dose response data a log-linear extrapolation method can be used to estimate an EC3 value which can reduce significantly the need for repeat testing of chemicals. The LLNA, when conducted according to published guidelines, provides a robust method for skin sensitization testing that not only provides reliable hazard identification information but also data necessary for effective risk assessment and risk management.

'PSA-SPN' - A Parameter Sensitivity Analysis Method Using Stochastic Petri Nets: Application to a Production Line System

International Nuclear Information System (INIS)

Labadi, Karim; Saggadi, Samira; Amodeo, Lionel

2009-01-01

The dynamic behavior of a discrete event dynamic system can be significantly affected for some uncertain changes in its decision parameters. So, parameter sensitivity analysis would be a useful way in studying the effects of these changes on the system performance. In the past, the sensitivity analysis approaches are frequently based on simulation models. In recent years, formal methods based on stochastic process including Markov process are proposed in the literature. In this paper, we are interested in the parameter sensitivity analysis of discrete event dynamic systems by using stochastic Petri nets models as a tool for modelling and performance evaluation. A sensitivity analysis approach based on stochastic Petri nets, called PSA-SPN method, will be proposed with an application to a production line system.

Lake and Reservoir Evaporation Estimation: Sensitivity Analysis and Ranking Existing Methods

Directory of Open Access Journals (Sweden)

maysam majidi

2016-02-01

were acquired from the Doosti Dam weather station. Relative humidity, wind speed, atmospheric pressure and precipitation were acquired from the Pol−Khatoon weather station. Dew point temperature and sunshine data were collected from the Sarakhs weather station. Lake area was estimated from hypsometric curve in relation to lake level data. Temperature measurements were often performed in 16−day periods or biweekly from September 2011 to September 2012. Temperature profile of the lake (required for lake evaporation estimation was measured at different points of the reservoir using a portable multi−meter. The eighteen existing methods were compared and ranked based on Bowen ratio energy balance method (BREB. Results and Discussion: The estimated annual evaporation values by all of the applied methods in this study, ranged from 21 to 113mcm (million cubic meters. BREB annual evaporation obtained value was equal to 69.86mcm and evaporation rate averaged 5.47mm d-1 during the study period. According to the results, there is a relatively large difference between the obtained evaporation values from the adopted methods. The sensitivity analysis of evaporation methods for some input parameters indicated that the Hamon method (Eq. 16 was the most sensitive to the input parameters followed by the Brutsaert−Stricker and BREB, and radiation−temperature methods (Makkink, Jensen−Haise and Stephen−Stewart had the least sensitivity to input data. Besides, the air temperature, solar radiation (sunshine data, water surface temperature and wind speed data had the most effect on lake evaporation estimations, respectively. Finally, all evaporation estimation methods in this study have been ranked based on RMSD values. On a daily basis, the Jensen−Haise and the Makkink (solar radiation, temperature group, Penman (Combination group and Hamon (temperature, day length group methods had a relatively reasonable performance. As the results on a monthly scale, the Jensen−Haise and

Evaluation of Alternative Methods for Testing the Bioefficacy of Household Ambient Insecticide Products Against Aedes albopictus.

Science.gov (United States)

Cassini, Rudi; Scremin, Mara; Contiero, Barbara; Drago, Andrea; Vettorato, Christian; Marcer, Federica; di Regalbono, Antonio Frangipane

2016-06-01

Ambient insecticides are receiving increasing attention in many developed countries because of their value in reducing mosquito nuisance. As required by the European Union Biocidal Products Regulation 528/2012, these devices require appropriate testing of their efficacy, which is based on estimating the knockdown and mortality rates of free-flying (free) mosquitoes in a test room. However, evaluations using free mosquitoes present many complexities. The performances of 6 alternative methods with mosquitoes held in 2 different cage designs (steel wire and gauze/plastic) with and without an operating fan for air circulation were monitored in a test room through a closed-circuit television system and were compared with the currently recommended method using free mosquitoes. Results for caged mosquitoes without a fan showed a clearly delayed knockdown effect, whereas outcomes for caged mosquitoes with a fan recorded higher mortality at 24 h, compared to free mosquitoes. Among the 6 methods, cages made of gauze and plastic operating with fan wind speed at 2.5-2.8 m/sec was the only method without a significant difference in results for free mosquitoes, and therefore appears as the best alternative to assess knockdown by ambient insecticides accurately.

Effect of parameters in moving average method for event detection enhancement using phase sensitive OTDR

Science.gov (United States)

Kwon, Yong-Seok; Naeem, Khurram; Jeon, Min Yong; Kwon, Il-bum

2017-04-01

We analyze the relations of parameters in moving average method to enhance the event detectability of phase sensitive optical time domain reflectometer (OTDR). If the external events have unique frequency of vibration, then the control parameters of moving average method should be optimized in order to detect these events efficiently. A phase sensitive OTDR was implemented by a pulsed light source, which is composed of a laser diode, a semiconductor optical amplifier, an erbium-doped fiber amplifier, a fiber Bragg grating filter, and a light receiving part, which has a photo-detector and high speed data acquisition system. The moving average method is operated with the control parameters: total number of raw traces, M, number of averaged traces, N, and step size of moving, n. The raw traces are obtained by the phase sensitive OTDR with sound signals generated by a speaker. Using these trace data, the relation of the control parameters is analyzed. In the result, if the event signal has one frequency, then the optimal values of N, n are existed to detect the event efficiently.

An alternative empirical likelihood method in missing response problems and causal inference.

Science.gov (United States)

Ren, Kaili; Drummond, Christopher A; Brewster, Pamela S; Haller, Steven T; Tian, Jiang; Cooper, Christopher J; Zhang, Biao

2016-11-30

Missing responses are common problems in medical, social, and economic studies. When responses are missing at random, a complete case data analysis may result in biases. A popular debias method is inverse probability weighting proposed by Horvitz and Thompson. To improve efficiency, Robins et al. proposed an augmented inverse probability weighting method. The augmented inverse probability weighting estimator has a double-robustness property and achieves the semiparametric efficiency lower bound when the regression model and propensity score model are both correctly specified. In this paper, we introduce an empirical likelihood-based estimator as an alternative to Qin and Zhang (2007). Our proposed estimator is also doubly robust and locally efficient. Simulation results show that the proposed estimator has better performance when the propensity score is correctly modeled. Moreover, the proposed method can be applied in the estimation of average treatment effect in observational causal inferences. Finally, we apply our method to an observational study of smoking, using data from the Cardiovascular Outcomes in Renal Atherosclerotic Lesions clinical trial. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

A Terbium Sensitized Luminescence Method for the Assay of Flubiprofen in Pharmaceutical Formulations

Directory of Open Access Journals (Sweden)

Salma M.Z. Al-Kindy

2014-12-01

Full Text Available A sensitive time-resolved luminescence method for the determination of flubiprofen (FLP in methanol and in aqueous solution is described. The method is based on the luminescence sensitization of terbium (Tb3+ by the formation of a ternary complex with FLP in the presence of 4,7 diphenyl 1,10 phenanthroline (DPP as co-ligand, and Tween-20 as surfactant. The signal for Tb-FLP-DPP was monitored at λex  = 285 nm and λem  = 552 nm. Optimum conditions for the formation of the complex in an aqueous system were TRIS buffer, pH 8.0, DPP (2.5Å~10−7  M, Tween-20 (0.30% and 4Å~10-5  mol L-1  of Tb3+  which allowed the determination of 20–1000 ng mL-1  of FLP with a limit of detection (LOD of 10 ng mL-1 . The relative standard deviations of the method ranged between 0.6 and 1.4% indicating excellent reproducibility of the method. The proposed method was successfully applied for the assays of FLP in pharmaceutical formulations and spiked tap water samples with average recoveries of 87% – 95%.

A pre-heating method based on sinusoidal alternating current for lithium-ion battery

Science.gov (United States)

Fan, Wentao; Sun, Fengchun; Guo, Shanshan

2018-04-01

In this paper, a method of low temperature pre-heating of sinusoidal alternating current (SAC) is proposed. Generally, the lower the frequency of the AC current, the higher the heat generation rate. Yet at low frequency, there is a risk of lithium-ion deposition during the half cycle of charging. This study develops a temperature-adaptive, deposition-free AC pre-heating method. a equivalent electric circuit(EEC) model is established to predict the heat generation rate and temperature status, whose parameters are calibrated from the EIS impedance measurements. The effects of current frequency and amplitude on the heating effect are investigated respectively. A multistep temperature-adaptive amplitude strategy is proposed and the cell can be heated from -20°C to 5°C within 509s at 100Hz frequency with this method.

Flexural modeling of the elastic lithosphere at an ocean trench: A parameter sensitivity analysis using analytical solutions

Science.gov (United States)

Contreras-Reyes, Eduardo; Garay, Jeremías

2018-01-01

The outer rise is a topographic bulge seaward of the trench at a subduction zone that is caused by bending and flexure of the oceanic lithosphere as subduction commences. The classic model of the flexure of oceanic lithosphere w (x) is a hydrostatic restoring force acting upon an elastic plate at the trench axis. The governing parameters are elastic thickness Te, shear force V0, and bending moment M0. V0 and M0 are unknown variables that are typically replaced by other quantities such as the height of the fore-bulge, wb, and the half-width of the fore-bulge, (xb - xo). However, this method is difficult to implement with the presence of excessive topographic noise around the bulge of the outer rise. Here, we present an alternative method to the classic model, in which lithospheric flexure w (x) is a function of the flexure at the trench axis w0, the initial dip angle of subduction β0, and the elastic thickness Te. In this investigation, we apply a sensitivity analysis to both methods in order to determine the impact of the differing parameters on the solution, w (x). The parametric sensitivity analysis suggests that stable solutions for the alternative approach requires relatively low β0 values (rise bulge. The alternative method is a more suitable approach, assuming that accurate geometric information at the trench axis (i.e., w0 and β0) is available.