WorldWideScience

Sample records for selective uptake properties

  1. Preparation of ferrocyanide molybdate and their selective uptake properties for palladium and cesium ions

    Energy Technology Data Exchange (ETDEWEB)

    Hitoshi, Mimura; Ayumi, Asakura; Yan, Wu; Yuichi, Niibori; Masaki, Ozawa [Tohoku Univ., Dept. of Quantum Science and Engineering Graduate School of Engineering (Japan)

    2007-07-01

    The selective separation of heat-generating nuclide (Cs) and platinum group metal (Pd) containing in high-level liquid wastes (HLLW) is an important subject for the advancement of nuclear fuel cycle. Selective uptake of these nuclides was accomplished by using insoluble ferrocyanide molybdates (FeMo-[1-4]). The uptake properties of Pd{sup 2+} and Cs{sup +} for MoFe-[1-4] in the presence of 1 M HNO{sub 3} were examined by batch method. Relatively high uptake percentages of Pd{sup 2+} and Cs{sup +} above 90% were obtained within 30 min. The uptake percentage above 90% was kept in the presence of 0.1-3 M HNO{sub 3}. The uptake selectivity of Pd{sup 2+} was higher than that of Cs{sup +}; the separation factor of Pd{sup 2+} to Cs{sup +} increased with coexisting HNO{sub 3} concentration and was estimated to be 15 at 3 M HNO{sub 3}. The uptake of Pd{sup 2+} and Cs{sup +} on FeMo-[1-4] followed a Langmuir-type adsorption equation, and the uptake capacities of Pd{sup 2+} and Cs{sup +} were estimated to be [0.17-0.28] and [1.68-2.24] mmol/g, respectively. The uptake is mainly governed by the ion-exchange reaction between exchangeable cations (Na{sup +} and K{sup +}) and target cations (Pd{sup 2+} and Cs{sup +}). Further, the selective uptake of Pd{sup 2+} and Cs{sup +} was confirmed by using simulated HLLW (28 components, SW-11, JAEA); the uptake equilibrium attained within 30 min and the uptake percentages of Pd{sup 2+} and Cs{sup +} were 99 and 85 %, respectively. In order to granulate the fine powders of FeMo exchangers, the alginate gel polymer was used as an immobilizing matrix for the micro-encapsulation. The uptake percentages of Pd{sup 2+} and Cs{sup +} for FeMo-3 micro-capsule were above 80% even in the presence of 3 M HNO{sub 3}. Thus the molybdate can be converted to the ion-exchanger having high selectivity towards Pd{sup 2+} and Cs{sup +} in HLLW. This conversion method leads to the volume reduction of wastes and the utilization of useful nuclides. (authors)

  2. Properties of Soils and Plants Uptake within the Vicinity of Selected ...

    African Journals Online (AJOL)

    Backyard farming is becoming popular among the auto mechanics near their workshops where spent engine oil and carcass of vehicles are continuously dumped in Nigeria. The properties of soil and maize plants sampled from the vicinity of selected auto mechanic workshops in Ile-Ife, Nigeria were investigated. The results ...

  3. Selective uptake of manganese in seawater by hybrid microcapsules

    International Nuclear Information System (INIS)

    Kuzumaki, Takenori; Yan, Wu; Mimura, Hitoshi; Niibori, Yuichi

    2008-01-01

    The selective separation and recovery of low concentrated elements in seawater are very important subjects for the advancement of environmental monitoring. Selective uptake of manganese from seawater was carried out by using two kinds of microcapsules (MCs) including activated carbon (AC) and insoluble tannin (T). The adsorbents, AC and T, having affinity for manganese, were enclosed into MCs (ACMS, TMC) by sol-gel method using matrices of biopolymer (calcium alginate gel polymer, CaALG). The uptake properties and selectivity of Mn 2+ (1 ppm) for MCs were examined by batch method. Relatively large uptake percentages of Mn 2+ above 80% were obtained within 1 h, and the uptake percentage above 80% was kept at pH 3-6. The uptake order was found to be T, AC, CaALG > ACMC, TMC. The uptake of Mn 2+ decreased with increasing Na + ion concentration. This tendency depends on the swelling property of CaALG; it tends to solate in the presence of highly concentrated Na + ions. The manganese ions were adsorbed on CaALG, ACMC and TMC from seawater containing 1,000 ppm Mn 2+ . ACMC and TMC had selectivity to Mn 2+ , and, especially, the matrices of CaALG also had an excellent uptake and selectivity properties. (author)

  4. Fluoxetine, a selective inhibitor of serotonin uptake, potentiates morphine analgesia without altering its discriminative stimulus properties or affinity for opioid receptors

    International Nuclear Information System (INIS)

    Hynes, M.D.; Lochner, M.A.; Bemis, K.G.; Hymson, D.L.

    1985-01-01

    The analgesic effect of morphine in the rat tail jerk assay was enhanced by the serotonin uptake inhibitor, fluoxetine. Tail jerk latency was not affected by fluoxetine alone. Morphine's affinity for opioid receptors labeled in vitro with 3 H-naloxone or 3 H-D-Ala 2 -D-Leu 5 -enkephalin was not altered by fluoxetine, which has no affinity for these sites at concentrations as high as 1000 nM. In rats trained to discriminate morphine from saline, fluoxetine at doses of 5 or 10 mg/kg were recognized as saline. Increasing the fluoxetine dose to 20 mg/kg did not result in generalization to either saline or morphine. The dose response curve for morphine generalization was not significantly altered by fluoxetine doses of 5 or 10 mg/kg. Those rats treated with the combination of morphine and 20 mg/kg of fluoxetine did not exhibit saline or morphine appropriate responding. Fluoxetine potentiates the analgesic properties of morphine without enhancing its affinity for opioid receptors or its discriminative stimulus properties. 30 references, 2 figures, 2 tables

  5. Selective uptake of boronophenylalanine by glioma stem/progenitor cells

    International Nuclear Information System (INIS)

    Sun, Ting; Zhou, Youxin; Xie, Xueshun; Chen, Guilin; Li, Bin; Wei, Yongxin; Chen, Jinming; Huang, Qiang; Du, Ziwei

    2012-01-01

    The success of boron neutron capture therapy (BNCT) depends on the amount of boron in cells and the tumor/blood and tumor/(normal tissue) boron concentration ratios. For the first time, measurements of boron uptake in both stem/progenitor and differentiated glioma cells were performed along with measurements of boron biodistribution in suitable animal models. In glioma stem/progenitor cells, the selective accumulation of boronophenylalanine (BPA) was lower, and retention of boron after BPA removal was longer than in differentiated glioma cells in vitro. However, boron biodistribution was not statistically significantly different in mice with xenografts. - Highlights: ► Uptake of BPA was analyzed in stem/progenitor and differentiated glioma cells. ► Selective accumulation of BPA was lower in glioma stem/progenitor cells. ► Retention of boron after BPA removal was longer in glioma stem/progenitor cells. ► Boron biodistribution was not statistically different in mice with xenografts.

  6. Cisplatin carbonato complexes. Implications for uptake, antitumor properties, and toxicity.

    Science.gov (United States)

    Centerwall, Corey R; Goodisman, Jerry; Kerwood, Deborah J; Dabrowiak, James C

    2005-09-21

    The reaction of aquated cisplatin with carbonate which is present in culture media and blood is described. The first formed complex is a monochloro monocarbonato species, which upon continued exposure to carbonate slowly forms a biscarbonato complex. The formation of carbonato species under conditions that simulate therapy may have important implications for uptake, antitumor properties, and toxicity of cisplatin.

  7. Effect of biosolids application on soil chemical properties and uptake ...

    African Journals Online (AJOL)

    Effect of biosolids application on soil chemical properties and uptake of some heavy metals by Cercis siliquastrum. ... and municipal solid waste compost (50% CM + 50% MC) at three levels of 0, 2.5 and 5 kg/shrub and three replicates in calcareous sandy loam soil at the botanical garden of Mobarekeh steel company.

  8. Selective mGAT2 (BGT-1) GABA Uptake Inhibitor

    DEFF Research Database (Denmark)

    Vogensen, Stine Byskov; Jørgensen, Lars; Madsen, Karsten Kirkegaard

    2013-01-01

    β-Amino acids sharing a lipophilic diaromatic side chain were synthesized and characterized pharmacologically on mouse GABA transporter subtypes mGAT1−4. The parent amino acids were also characterized. Compounds 13a, 13b, and 17b displayed more than 6-fold selectivity for mGAT2 over mGAT1. Compou...... 17b displayed anticonvulsive properties inferring a role of mGAT2 in epileptic disorders. These results provide new neuropharmacological tools and a strategy for designing subtype selective GABA transport inhibitors....

  9. Influence of tragacanth gum in egg white based bioplastics: Thermomechanical and water uptake properties.

    Science.gov (United States)

    López-Castejón, María Luisa; Bengoechea, Carlos; García-Morales, Moisés; Martínez, Inmaculada

    2016-11-05

    This study aims to extend the range of applications of tragacanth gum by studying its incorporation into bioplastics formulation, exploring the influence that different gum contents (0-20wt.%) exert over the thermomechanical and water uptake properties of bioplastics based on egg white albumen protein (EW). The effect of plasticizer nature was also evaluated through the modification of the water/glycerol ratio within the plasticizer fraction (fixed at 40wt.%). The addition of tragacanth gum generally yielded an enhancement of the water uptake capacity, being doubled at the highest content. Conversely, presence of tragacanth gum resulted in a considerable decrease in the bioplastic mechanical properties: both tensile strength and maximum elongation were reduced up to 75% approximately when compared to the gum-free system. Ageing of selected samples was also studied, revealing an important effect of storage time when tragacanth gum is present, possibly due to its hydrophilic character. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Engineering recombinant EF-hand peptides for selective uranium uptake

    Energy Technology Data Exchange (ETDEWEB)

    Berthomieu, C.; Pardoux, R.; Beccia, M.R.; Lemaire, D.; Sauge-Merle, S. [CEA, DSV, IBEB, UMR7265 CNRS CEA Aix-Marseille Univ. (France); Guilbaud, P. [CEA, DRCPC, SMCS, LILA (France); Delangle, P. [CEA, INAC, Service de Chimie Inorganique et Biologique (France)

    2014-07-01

    In spite of an increasing number of publications in recent years, information regarding the mechanism of uranium interaction with proteins at the molecular level is limited and few quantitative studies have investigated the binding properties of uranyl with proteins or peptides. It is thus of great interest to better characterize these interactions, and to analyze structural factors governing uranyl binding and thermodynamic stabilization in proteins. Research in this direction will benefit our understanding of the molecular factors governing uranyl toxicity and speciation in cells and will also aid in developing new molecules for selectively binding uranium that could be used for uranium bioremediation purposes. Uranyl coordination properties have similarities with those of calcium, i.e electrostatic interactions preferentially with hard donor oxygen ligands and pentagonal bipyramidal structures. The EF-hand structural motif is the most prevalent Ca2{sup +-}binding site in proteins and is very appealing to analyse uranyl binding properties and develop affine and specific uranyl binding sites for biotechnology approaches. We selected the recombinant N-terminal domain of calmodulin from A. thaliana as a structured template that contains two EF-hand motifs (site I and site II) to analyze its uranyl binding properties and to engineer peptide variants with increased uranyl affinity and specificity. We showed that both site I and site II bind uranyl, with a dissociation constant in the nano-molar range for site I (K{sub d} ≅ 25 nM at pH 6). Using in vitro phosphorylation of a threonine located in the uranyl binding loop, we measured how adding a phosphoryl group affects the calcium and uranium binding affinities. The phosphorylated peptide exhibited a very large affinity for uranyl at pH 7, with a dissociation constant in the sub-nano-molar range K{sub d} = 0.25 ±0.06 nM, and FTIR analysis demonstrated that the phosphoryl group plays a determining role in uranyl

  11. The market dynamics of selective serotonin re-uptake inhibitors: a ...

    African Journals Online (AJOL)

    The market dynamics of selective serotonin re-uptake inhibitors: a private sector study in South Africa. Frasia Oosthuizen, Pariksha Jolene Kondiah, Hawa Bibi Moosa, Siddiqa Naroth, Nabeel Ismail Patel, Divashnee Reddy, Amanda Soobramoney ...

  12. Heavy metal ion uptake properties of polystyrene-supported ...

    Indian Academy of Sciences (India)

    Unknown

    concentration on the uptake of metal ions have been studied. The uptake ... employed for the removal of heavy metal pollutants from industrial waste water. ... nitrate, mercuric chloride, cadmium nitrate and potassium dichromate salts. ... polymer resin was determined by reacting 50, 100, 150, 200, 250 and 300 ppm of metal.

  13. Cellular uptake of nanoparticles as determined by particle properties, experimental conditions, and cell type.

    Science.gov (United States)

    Kettler, Katja; Veltman, Karin; van de Meent, Dik; van Wezel, Annemarie; Hendriks, A Jan

    2014-03-01

    The increased application of nanoparticles (NPs) is increasing the risk of their release into the environment. Although many toxicity studies have been conducted, the environmental risk is difficult to estimate, because uptake mechanisms are often not determined in toxicity studies. In the present study, the authors review dominant uptake mechanisms of NPs in cells, as well as the effect of NP properties, experimental conditions, and cell type on NP uptake. Knowledge of NP uptake is crucial for risk assessment and is essential to predict the behavior of NPs based on their physical-chemical properties. Important uptake mechanisms for eukaryotic cells are macropinocytosis, receptor-mediated endocytosis, and phagocytosis in specialized mammalian cells. The studies reviewed demonstrate that uptake into nonphagocytic cells depends strongly on NP size, with an uptake optimum at an NP diameter of approximately 50 nm. Increasing surface charges, either positive or negative, have been shown to increase particle uptake in comparison with uncharged NPs. Another important factor is the degree of (homo-) aggregation. Results regarding shape have been ambiguous. Difficulties in the production of NPs, with 1 property changed at a time, call for a full characterization of NP properties. Only then will it be possible to draw conclusions as to which property affected the uptake. © 2013 SETAC.

  14. Factors affecting heavy metal uptake in plant selection for phytoremediation

    Energy Technology Data Exchange (ETDEWEB)

    Anton, A.; Mathe-Gaspar, G. [Research Inst. for Soil Science and Agricultural Chemistry of the Hungarian Academy of Sciences, Budapest (Hungary)

    2005-04-01

    The heavy metal uptake of ten plant species was studied under different soil and climatic conditions. Effects of soil pH, temperature, plant species and phenophase on the heavy metal content of stems and leaves were determined in pot experiments. Plants and soil samples were collected from a lead/zinc mine ore (Gyoengyoesoroszi, Hungary) and characterised by high contents of Pb, Zn, As, Cd, Cu. The possibility of an adapted phytoremediation technology was indicated by different bioconcentration factors (BCF). The BCF depended markedly (10- to 100-fold) on plant species and environmental conditions. Based on our results a ''season-adapted'' phytoextraction technology with different plant species (utilising their different temperature requirements and/or harvest time) is suggested. (orig.)

  15. [Long-Term Inhibition of FNA on Aerobic Phosphate Uptake and Variation of Phosphorus Uptake Properties of the Sludge].

    Science.gov (United States)

    Ma, Juan; Li, Lu; Yu, Xiao-jun; Sun, Lei-jun; Sun, Hong-wei; Chen, Yong-zhi

    2015-10-01

    An alternating anaerobic/oxic ( An/O) sequencing batch reactor (SBR) was employed to investigate the long-term inhibitory effect of free nitrous acid (FNA) on aerobic phosphorus uptake performance and variation of phosphorus uptake properties of the sludge by adding nitrite. The reactor was started up under the condition of 21-23 degrees C. The results showed that FNA had no impact on phosphate release and uptake capacities of the sludge. However, the specific phosphate release/uptake rates was found to be higher. As FNA concentration (measure by HNO2-N) was lower than 0.53 x 10(-3) mg x L(-1), phosphorus removal efficiency of the system was higher than 96.9%. When the FNA concentration was increased to 0.99 x 10(-3) mg x L(-1), 1.46 x 10(-3) mg x L(-1) and 1.94 x 10(-3) mg x L(-1), the phosphorus removal performance deteriorated rapidly. The phosphorus removal efficiency was recovered to 64.42%, 67.33% and 44.14% after 50, 12 and 30 days, respectively, which implied the deterioration of phosphorus removal performance caused by FNA inhibition could be recovered and long-term acclimation could shorten the recovery process. Notably, increasing nitrite consumption appeared during aerobic phase with the concentration of FNA below 1.46 x 10(-3) mg x L(-1). It was also observed that the phosphorus uptake properties of the sludge varied after long-term inhibition. Nitrate and nitrite type anoxic phosphorus uptake capacity was increased by 3.35 and 3.86 times, respectively, suggesting long-term dosing FNA may facilitate the denitrifying of polyphosphate in organisms utilizing nitrite as electron acceptor. Moreover, long-term acclimation favored sludge settling.

  16. Selected Phytochemicals and Culinary Plant Extracts Inhibit Fructose Uptake in Caco-2 Cells.

    Science.gov (United States)

    Lee, Yurim; Lim, Yeni; Kwon, Oran

    2015-09-18

    This study compared the ability of nine culinary plant extracts containing a wide array of phytochemicals to inhibit fructose uptake and then explored the involvement of intestinal fructose transporters and phytochemicals for selected samples. The chemical signature was characterized by high performance liquid chromatography with mass spectrometry. Inhibition of [(14)C]-fructose uptake was tested by using human intestinal Caco-2 cells. Then, the relative contribution of the two apical-facing intestinal fructose transporters, GLUT2 and GLUT5, and the signature components for fructose uptake inhibition was confirmed in naive, phloretin-treated and forskolin-treated Caco-2 cells. HPLC/MS analysis of the chemical signature revealed that guava leaf contained quercetin and catechin, and turmeric contained curcumin, bisdemethoxycurcumin and dimethoxycurcumin. Similar inhibition of fructose uptake (by ~50%) was observed with guava leaf and turmeric in Caco-2 cells, but with a higher contribution of GLUT2 for turmeric and that of GLUT5 for guava leaf. The data suggested that, in turmeric, demethoxycurcumin specifically contributed to GLUT2-mediated fructose uptake inhibition, and curcumin did the same to GLUT5-mediated fructose uptake inhibition, but GLUT2 inhibition was more potent. By contrast, in guava leaf, catechin specifically contributed to GLUT5-mediated fructose uptake inhibition, and quercetin affected both GLUT5- and GLUT2-mediated fructose uptake inhibition, resulting in the higher contribution of GLUT5. These results suggest that demethoxycurcumin is an important contributor to GLUT2-mediated fructose uptake inhibition for turmeric extract, and catechin is the same to GLUT5-mediated fructose uptake inhibition for guava leaf extract. Quercetin, curcumin and bisdemethoxycurcumin contributed to both GLUT5- and GLUT2-mediated fructose uptake inhibition, but the contribution to GLUT5 inhibition was higher than the contribution to GLUT2 inhibition.

  17. Influence of coal properties on mercury uptake from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Lakatos, J.; Brown, S.D.; Snape, C.E. [Miskolc University, Miskolc-Egyetemvaros (Hungary). Research Inst. of Applied Chemistry

    1999-10-01

    The uptake of mercury (II) from aqueous solution by a range of coals has been studied and the results have been compared to those for a number of other sorbents, including commercial active carbons and cation-exchange resins. At pH 5 in a buffer medium, the capacities for mercury removal of the low-rank coals and the oxidized bituminous coals investigated are comparable to those of the other sorbents tested. For the lignites investigated, a high content of organic sulfur does not markedly affect the capacity for mercury uptake in relatively neutral and low chloride media, owing to redox reactions being the most likely mechanism involved. However, in highly acidic solutions, the capacities for mercury uptake are considerably greater for the high-sulfur coals investigated than for their low-sulfur counterparts due to chelation being the major sorption process involved. 36 refs., 4 figs., 7 tabs.

  18. Relationship of dough thermomechanical properties with oil uptake, cooking and textural properties of instant fried noodles.

    Science.gov (United States)

    Gulia, Neelam; Khatkar, B S

    2014-04-01

    Instant noodles were prepared from fifteen diverse wheat cultivars varying widely in their flour quality and dough rheology. Dough thermomechanical parameters obtained by Mixolab and flour analytical properties were correlated with the quality of instant noodles including oil uptake, cooking quality and textural attributes. The Mixolab parameters dough development time and dough stability showed significant positive correlation with cooking time, cooked weight, overall acceptability, hardness, springiness, cohesiveness and chewiness of noodles, while negatively correlated with oil uptake and cooking loss, therefore, exhibiting a marked positive effect on quality of instant noodles. Lower protein breakdown represented by C2 torque was also positively related with overall acceptability, hardness, springiness, cohesiveness and chewiness of noodles. Stickiness/adhesiveness of noodles was revealed to be mainly conferred by falling number values (R (2 )= 0.671) and damaged starch (R (2 )= 0.523) content of wheat flour samples. Flour samples with lesser values of protein content, sodium dodecyl sulphate sedimentation volume, thermal stability of proteins, dough stability and dough development time were found to be linked with poor noodle quality. Medium strong flours performed better in noodle making, while weaker flours demonstrated poor noodle quality. Dough rheology of good noodle making flours was characterized with higher dough development time, dough stability, C2, C3, C4 as well as C5 values. Noodles with higher overall acceptability showed a more continuous and uniform protein starch matrix in comparison to the poor counterparts.

  19. Heavy metals uptake by sonicated activated sludge: Relation with floc surface properties

    International Nuclear Information System (INIS)

    Laurent, Julien; Casellas, Magali; Dagot, Christophe

    2009-01-01

    The effects of sonication of activated sludge on heavy metal uptake were in a first time investigated in respect with potential modifications of floc surface properties. The treatment led to the simultaneous increase of specific surface area and of the availability of negative and/or hydrophilic sites. In parallel, organic matter was released in the soluble fraction. Sorption isotherms of cadmium and copper showed that uptake characteristics and mechanisms were highly dependent on both heavy metal species and specific energy supplied. The increase of both specific surface area and fixation sites availability led to the increase of Cd(II) uptake. For Cu(II), organic matter released in soluble phase during the treatment seemed to act as a ligand and to limit adsorption on flocs surface. Three different heavy metals uptake mechanisms have been identified: proton exchange, ion exchange and (co)precipitation

  20. Effects of soil properties on the uptake of pharmaceuticals into earthworms

    International Nuclear Information System (INIS)

    Carter, Laura J.; Ryan, Jim J.; Boxall, Alistair B.A.

    2016-01-01

    Pharmaceuticals can enter the soil environment when animal slurries and sewage sludge are applied to land as a fertiliser or during irrigation with contaminated water. These pharmaceuticals may then be taken up by soil organisms possibly resulting in toxic effects and/or exposure of organisms higher up the food chain. This study investigated the influence of soil properties on the uptake and depuration of pharmaceuticals (carbamazepine, diclofenac, fluoxetine and orlistat) in the earthworm Eisenia fetida. The uptake and accumulation of pharmaceuticals into E. fetida changed depending on soil type. Orlistat exhibited the highest pore water based bioconcentration factors (BCFs) and displayed the largest differences between soil types with BCFs ranging between 30.5 and 115.9. For carbamazepine, diclofenac and fluoxetine BCFs ranged between 1.1 and 1.6, 7.0 and 69.6 and 14.1 and 20.4 respectively. Additional analysis demonstrated that in certain treatments the presence of these chemicals in the soil matrices changed the soil pH over time, with a statistically significant pH difference to control samples. The internal pH of E. fetida also changed as a result of incubation in pharmaceutically spiked soil, in comparison to the control earthworms. These results demonstrate that a combination of soil properties and pharmaceutical physico-chemical properties are important in terms of predicting pharmaceutical uptake in terrestrial systems and that pharmaceuticals can modify soil and internal earthworm chemistry which may hold wider implications for risk assessment. - Highlights: • Uptake of pharmaceuticals into earthworms is influenced by soil parameters. • Presence of pharmaceuticals in the terrestrial environment influences soil pH. • Uptake of pharmaceuticals by earthworms changes internal earthworm pH. - The uptake of pharmaceuticals into soil invertebrates is dependent on the complex interplay between pharmaceutical physico-chemical properties and soil

  1. Influence of soil agrochemical properties for 90Sr uptake by cereals in radioactive contaminated zone

    International Nuclear Information System (INIS)

    Putyatin, Yu.V.; Vetrova, N.N.

    2001-05-01

    The adequate estimation of necessity of carrying out of protective measures is one of most prominent aspects of conducting agro-industrial production in a period after Chernobyl NPP failure in conditions of a deficit of the investments. The problem of diminution of dose loadings on the population is solved first of all by complex of agricultural protective measures, as about 70 percents of a collective dose is shaped at the expense of entering radionuclide uptake of in an organism with foodstuff. The application of protective measures in agriculture allows essentially to lower the radionuclide content in foodstuff. The liming, extra rates of potassium and phosphorus fertilizers are basic elements of the plant production technology in radioactive contaminated zone, which results in essential change of soil agrochemical properties. Main purpose of the study was on the basis of the experimental data to establish threshold soil parameters, which excess does not provide of 90 Sr uptake reduction in grain. The mathematical processing of results of 90 Sr radiochemical analysis with samples of sod-podsolic loamy sand soil and cereals selected from trial plots of Gomel and Mogilev regions has shown, that the inhibiting action of 90 Sr uptake decrease in grain is noted at pH (1N KCl) - 6,4 for rye, spring wheat -- 6,7, barley -- 6,7. The quantity of reliability of approximating -R 2 for rye has made 0,55, summer wheat 0,49 and barley 0,72. As a whole, the levels of soil acidity correspond to optimal parameters for production of maximal yields. The liming of soil by dolomite is accompanied with rising of exchangeable Ca and Mg contents. The correlation analysis has shown, that R 2 for the Ca content in soil and 90 Sr accumulation by rye was -- 0,38, spring wheat -- 0,69 and barley -- 0,47. The impairment of influence of calcium concentration of soil is noted at 1420 ppm for rye and 781 ppm Ca for barley. For exchangeable Mg is noted limits for rye --140(R 2 -- 0.54), spring

  2. The effect of water uptake on the mechanical properties of low-k organosilica glass

    Science.gov (United States)

    X. Guo; J.E. Jakes; M.T. Nichols; S. Banna; Y. Nishi; J.L. Shohet

    2013-01-01

    Water uptake in porous low-k dielectrics has become a significant challenge for both back-end-of line integration and circuit reliability. The influence of absorbed water on the mechanical properties of plasma-enhanced chemical-vapor-deposited organosilicate glasses (SiCOH) was investigated with nanoindentation. The roles of physisorbed (α-...

  3. In vitro effects of toxaphene on mitochondrial calcium ATPase and calcium uptake in selected rat tissues

    International Nuclear Information System (INIS)

    Trottman, C.H.; Rao, K.S.P.; Morrow, W.; Uzodinma, J.E.; Desaiah, D.

    1985-01-01

    In vitro effects of toxaphene on Ca 2+ -ATPase activity and 45 Ca 2+ -uptake were studied in mitochondrial fractions of heart, kidney and liver tissues of rat. Mitochondrial fractions were prepared by the conventional centrifugation method. Ca 2+ -ATPase activity was determined by measuring the inorganic phosphate liberated during ATP hydrolysis. Toxaphene inhibited Ca 2+ -ATPase in a concentration dependent manner in all the three tissues. Substrate activation kinetics, with heart, kidney and liver tissue fractions, revealed that toxaphene inhibited Ca 2+ -ATPase activity non-competetively by decreasing the maximum velocity of the enzyme without affecting the enzyme-substrate affinity. Toxaphene also inhibited mitochondrial 45 Ca 2+ -uptake in the three selected tissues in a concentration dependent manner. These results indicate that toxaphene is an inhibitor of mitochondrial Ca 2+ -ATPase and calcium transport in heart, kidney and liver tissues of rat. 19 references, 5 figures

  4. Material properties that predict preservative uptake for silicone hydrogel contact lenses.

    Science.gov (United States)

    Green, J Angelo; Phillips, K Scott; Hitchins, Victoria M; Lucas, Anne D; Shoff, Megan E; Hutter, Joseph C; Rorer, Eva M; Eydelman, Malvina B

    2012-11-01

    To assess material properties that affect preservative uptake by silicone hydrogel lenses. We evaluated the water content (using differential scanning calorimetry), effective pore size (using probe penetration), and preservative uptake (using high-performance liquid chromatography with spectrophotometric detection) of silicone and conventional hydrogel soft contact lenses. Lenses grouped similarly based on freezable water content as they did based on total water content. Evaluation of the effective pore size highlighted potential differences between the surface-treated and non-surface-treated materials. The water content of the lens materials and ionic charge are associated with the degree of preservative uptake. The current grouping system for testing contact lens-solution interactions separates all silicone hydrogels from conventional hydrogel contact lenses. However, not all silicone hydrogel lenses interact similarly with the same contact lens solution. Based upon the results of our research, we propose that the same material characteristics used to group conventional hydrogel lenses, water content and ionic charge, can also be used to predict uptake of hydrophilic preservatives for silicone hydrogel lenses. In addition, the hydrophobicity of silicone hydrogel contact lenses, although not investigated here, is a unique contact lens material property that should be evaluated for the uptake of relatively hydrophobic preservatives and tear components.

  5. Selective WGA uptake in the hippocampus from the locus coeruleus of DBH-WGA transgenic mice

    Directory of Open Access Journals (Sweden)

    Susan G eWalling

    2012-05-01

    Full Text Available We generated transgenic mice in which a transsynaptic tracer, wheat germ agglutinin (WGA, was specifically expressed in the locus coeruleus neurons under the control of the dopamine-β-hydroxylase gene promoter. WGA protein was produced in more than 95% of the tyrosine hydroxylase-positive locus coeruleus neurons sampled. Transynaptic transfer of WGA was most evident in CA3 neurons of the hippocampus, but appeared absent in CA1 neurons. Faint but significant WGA immunoreactivity was observed surrounding the nuclei of dentate granule cells. Putative hilar mossy cells, identified by the presence of calretinin in the ventral hippocampus, appeared uniformly positive for transynaptically transferred WGA protein. GAD67-positive interneurons in the hilar and CA3 regions tended to be WGA-positive, although a subset of them did not show WGA co-localization. The same mixed WGA uptake profile was apparent when examining co-localization with parvalbumin. The selective uptake of WGA by dentate granule cells, mossy cells and CA3 pyramidal neurons is consistent with evidence for a large proportion of conventional synapses adjacent to locus coeruleus axonal varicosities in these regions. The lack of WGA uptake in the CA1 region and its relatively sparse innervation by dopamine-β-hydroxylase-positive fibers suggest that a majority of the tyrosine hydroxylase-positive classical synapses revealed by electron microscopy in that region may be producing dopamine. The overall pattern of WGA uptake in these transgenic mice suggests a selective role for the granule cell-mossy cell-CA3 network in processing novelty or the salient environmental contingency changes signaled by locus coeruleus activity.

  6. Thermo-Physical Properties of Selected Inconel

    Directory of Open Access Journals (Sweden)

    Krajewski P.K.

    2014-10-01

    Full Text Available The paper brings results of examinations of main thermo-physical properties of selected Inconel alloys, i.e. their heat diffusivity, thermal conductivity and heat capacity, measured in wide temperature range of 20 – 900 oC. Themathematical relationships of the above properties vs. temperature were obtained for the IN 100 and IN 713C alloys. These data can be used when modelling the IN alloys solidification processes aimed at obtaining required structure and properties as well as when designing optimal work temperature parameters.

  7. The selective uptake of uranium and thorium from the environment by some vegetables

    International Nuclear Information System (INIS)

    Yusof, A.M.; Ghazali, Z.; Abdul-Rahman, S.; Sharif, J.

    1991-01-01

    An attempt was made to establish baseline information on environmental pollution in locally-grown vegetables by uranium and thorium. Lowland and highland species together with soil and fertilizer samples were collected and analyzed using fluorimetry, spectrophotometry and delayed neutron counting techniques. All leafy vegetables observed showed high uranium and thorium uptake especially those grown in the lowlands. Those grown in the highlands reflected no direct relationship in uranium and thorium contents. Several species common in both sampling areas exhibited direct relationship between these two elements making them as potential bio-indicators. Figures calculated for fruit-type and leafy vegetables were not only comparatively low but bore no direct correlation between the two elements. The use of phosphate-based fertilizers on some of the leafy species in the lowlands did not enhance the uptake of these elements in spite of the higher uranium and thorium contents in soil samples from the lowlands, between 20-85 μg/g for uranium and 43-226 μg/g thorium compared to about 13-20 μg/g and 35-55 μg/g respectively for soil samples in the highlands. Statistical analysis was done to substantiate these findings. Climatic conditions were also taken into account as one of the factors affecting selective uptake of these elements in the vegetables

  8. Scoparia dulcis (SDF7) endowed with glucose uptake properties on L6 myotubes compared insulin.

    Science.gov (United States)

    Beh, Joo Ee; Latip, Jalifah; Abdullah, Mohd Puad; Ismail, Amin; Hamid, Muhajir

    2010-05-04

    Insulin stimulates glucose uptake and promotes the translocation of glucose transporter 4 (Glut 4) to the plasma membrane on L6 myotubes. The aim of this study is to investigate affect of Scoparia dulcis Linn water extracts on glucose uptake activity and the Glut 4 translocation components (i.e., IRS-1, PI 3-kinase, PKB/Akt2, PKC and TC 10) in L6 myotubes compared to insulin. Extract from TLC fraction-7 (SDF7) was used in this study. The L6 myotubes were treated by various concentrations of SDF7 (1 to 50 microg/ml) and insulin (1 to 100 nM). The glucose uptake activities of L6 myotubes were evaluated using 2-Deoxy-D-glucose uptake assay in with or without fatty acid-induced medium. The Glut 4 translocation components in SDF7-treated L6 myotubes were detected using immunoblotting and quantified by densitometry compared to insulin. Plasma membrane lawn assay and glycogen colorimetry assay were carried out in SDF7- and insulin-treated L6 myotubes in this study. Here, our data clearly shows that SDF7 possesses glucose uptake properties on L6 myotubes that are dose-dependent, time-dependent and plasma membrane Glut 4 expression-dependent. SDF7 successfully stimulates glucose uptake activity as potent as insulin at a maximum concentration of 50 microg/ml at 480 min on L6 myotubes. Furthermore, SDF7 stimulates increased Glut 4 expression and translocation to plasma membranes at equivalent times. Even in the insulin resistance stage (free fatty acids-induced), SDF7-treated L6 myotubes were found to be more capable at glucose transport than insulin treatment. Thus, we suggested that Scoparia dulcis has the potential to be categorized as a hypoglycemic medicinal plant based on its good glucose transport properties. (c) 2010 Elsevier Ireland Ltd. All rights reserved.

  9. Highly selective and stable carbon dioxide uptake in polyindole-derived microporous carbon materials.

    Science.gov (United States)

    Saleh, Muhammad; Tiwari, Jitendra N; Kemp, K Christain; Yousuf, Muhammad; Kim, Kwang S

    2013-05-21

    Adsorption with solid sorbents is considered to be one of the most promising methods for the capture of carbon dioxide (CO₂) from power plant flue gases. In this study, microporous carbon materials used for CO₂ capture were synthesized by the chemical activation of polyindole nanofibers (PIF) at temperatures from 500 to 800 °C using KOH, which resulted in nitrogen (N)-doped carbon materials. The N-doped carbon materials were found to be microporous with an optimal adsorption pore size for CO₂ of 0.6 nm and a maximum (Brunauer-Emmett-Teller) BET surface area of 1185 m(2) g(-1). The PIF activated at 600 °C (PIF6) has a surface area of 527 m(2) g(-1) and a maximum CO₂ storage capacity of 3.2 mmol g(-1) at 25 °C and 1 bar. This high CO₂ uptake is attributed to its highly microporous character and optimum N content. Additionally, PIF6 material displays a high CO₂ uptake at low pressure (1.81 mmol g(-1) at 0.2 bar and 25 °C), which is the best low pressure CO₂ uptake reported for carbon-based materials. The adsorption capacity of this material remained remarkably stable even after 10 cycles. The isosteric heat of adsorption was calculated to be in the range of 42.7-24.1 kJ mol(-1). Besides the excellent CO₂ uptake and stability, PIF6 also exhibits high selectivity values for CO₂ over N₂, CH₄, and H₂ of 58.9, 12.3, and 101.1 at 25 °C, respectively, and these values are significantly higher than reported values.

  10. Selective uptake and biological consequences of environmentally relevant antidepressant pharmaceutical exposures on male fathead minnows

    Science.gov (United States)

    Schultz, Melissa M.; Painter, Meghan M.; Bartell, Stephen E.; Logue, Amanda; Furlong, Edward T.; Werner, Stephen L.; Schoenfuss, Heiko L.

    2011-01-01

    Antidepressant pharmaceuticals have been reported in wastewater effluent at the nanogram to low microgram-per-liter range, and include bupropion (BUP), fluoxetine (FLX), sertraline (SER), and venlafaxine (VEN). To assess the effects of antidepressants on reproductive anatomy, physiology, and behavior, adult male fathead minnows (Pimeplwles promelas) were exposed for 21 days either to a single concentration of the antidepressants FLX, SER, VEN, or BUP, or to an antidepressant mixture. The data demonstrated that exposure to VEN (305 ng/L and 1104 ng/L) and SER (5.2 ng/L) resulted in mortality. Anatomical alterations were noted within the testes of fish exposed to SER and FLX, both modulators of the neurotransmitter serotonin. Additionally, FLX at 28 ng/L induced vitellogenin in male fish—a common endpoint for estrogenic endocrine disruption. Significant alterations in male secondary sex characteristics were noted with single exposures. Effects of single compound exposures neither carried over, nor became additive in the antidepressant mixtures, and reproductive behavior was not affected. Analysis of brain tissues from the exposed fish suggested increased uptake of FLX, SER and BUP and minimal uptake of VEN when compared to exposure water concentrations. Furthermore, the only metabolite detected consistently in the brain tissues was norfluoxetine. Similar trends of uptake by brain tissue were observed when fish were exposed to antidepressant mixtures. The present study demonstrates that anatomy and physiology, but not reproductive behavior, can be disrupted by exposure to environmental concentrations of some antidepressants. The observation that antidepressant uptake into fish tissues is selective may have consequences on assessing the mode-of-action and effects of these compounds in future studies.

  11. Plant uptake of 134Cs in relation to soil properties and time

    International Nuclear Information System (INIS)

    Massas, I.; Skarlou, V.; Haidouti, C.

    2002-01-01

    134 Cs uptake by sunflower and soybean plants grown on seven different soils and its relation to soil properties were studied in a greenhouse pot experiment. Soil in each pot was contaminated by dripping the 134 Cs in layers, and sunflower and soybean plants were grown for three and two successive periods, respectively. 134 Cs plant uptake was expressed as the transfer factor (TF) (Bq kg -1 plant/Bq kg -1 soil) and as the daily plant uptake (flux) (Bq pot -1 day -1 ) taking into account biomass production and growth time. For the studied soils and for both plants, no consistent trend of TFs with time was observed. The use of fluxes, in general, provided less variable results than TFs and stronger functional relationships. A negative power functional relationship between exchangeable potassium plus ammonium cations expressed as a percentage of cation exchange capacity of each soil and 134 Cs fluxes was found for the sunflower plants. A similar but weaker relationship was observed for soybean plants. The significant correlation between sunflower and soybean TFs and fluxes, as well as the almost identical highest/lowest 134 Cs flux ratios, in the studied soils, indicated a similar effect of soil characteristics on 134 Cs uptake by both plants. In all the studied soils, sunflower 134 Cs TFs and fluxes were significantly higher than the respective soybean values, while no significant difference was observed in potassium content and daily potassium plant uptake (flux) of the two plants

  12. Release Properties and Cellular Uptake in Caco-2 Cells of Size-Controlled Chitosan Nanoparticles.

    Science.gov (United States)

    Je, Hyun Jeong; Kim, Eun Suh; Lee, Ji-Soo; Lee, Hyeon Gyu

    2017-12-20

    The influences of particle size on the physicochemical, release, and cellular uptake properties of chitosan nanoparticles (CSNPs) were investigated. Ionotropic CSNPs of different sizes (200-1000 nm) loaded with two model core materials (resveratrol or coumarin-6) were prepared using tripolyphosphate and carrageenan as cross-linkers. With an increase of particle size, zeta potential (34.6 ± 0.5 to 51.1 ± 0.9) and entrapment efficiency (14.9 ± 1.4 to 40.9 ± 1.9) of the CSNPs were significantly (p cellular uptake of CSNPs were significantly increased from 3.70 ± 0.03 to 5.24 ± 0.20 with an increase of particle size from 200 to 600 nm, whereas those significantly decreased from 5.24 ± 0.20 to 4.55 ± 0.2 for particles larger than 600 nm in transwell assay. Moreover, much the same uptake patterns were also observed in confocal microscopy and flow cytometry. Investigation of cellular uptake of CSNPs revealed positive correlations between ZP and EE and indicated the effects of complex factors of nanoparticles other than size. These results provide a better understanding of CSNPs absorption and raises the possibility of controlling alternative nanoparticle properties to enhance bioavailability.

  13. Compost and Crude Humic Substances Produced from Selected Wastes and Their Effects on Zea mays L. Nutrient Uptake and Growth

    Science.gov (United States)

    Palanivell, Perumal; Susilawati, Kasim; Ahmed, Osumanu Haruna; Majid, Nik Muhamad

    2013-01-01

    Production of agriculture and timber commodities leads generation of enormous quantity of wastes. Improper disposal of these agroindustrial wastes pollutes the environment. This problem could be reduced by adding value to them. Therefore, a study was carried out to analyse and compare the nutrients content of RS, RH, SD, and EFB of composts and crude humic substances; furthermore, their effect on growth, dry matter production, and nutrient uptake for Zea mays L., and selected soil chemical properties were evaluated. Standard procedures were used to analyze humic acids (HA), crude fulvic acids (CFA), crude humin (CH), soil, dry matter production and nutrient uptake. Sawdust and RS compost matured at 42 and 47 days, respectively, while RH and EFB composts were less matured at 49th day of composting. Rice straw compost had higher ash, N, P, CEC, HA, K, and Fe contents with lower organic matter, total organic carbon, and C/N and C/P ratios. The HA of sawdust compost showed higher carbon, carboxylic, K, and Ca contents compared to those of RS, RH, and EFB. Crude FA of RS compost showed highest pH, total K, Ca, Mg, and Na contents. Crude humin from RS compost had higher contents of ash, N, P, and CEC. Rice straw was superior in compost, CFA, and CH, while sawdust compost was superior in HA. Application of sawdust compost significantly increased maize plants' diameter, height, dry matter production, N, P, and cations uptake. It also reduced N, P, and K based chemical fertilizer use by 90%. Application of CH and the composts evaluated in this study could be used as an alternative for chemical fertilizers in maize cultivation. PMID:24319353

  14. Neutron autoradiography imaging of selective boron uptake in human metastatic tumours

    Energy Technology Data Exchange (ETDEWEB)

    Altieri, S. [Department of Nuclear and Theoretical Physics, University of Pavia, Via Bassi 6, Pavia (Italy); National Institute of Nuclear Physics (INFN), Section of Pavia, Via Bassi 6, Pavia (Italy)], E-mail: saverio.altieri@pv.infn.it; Bortolussi, S. [Department of Nuclear and Theoretical Physics, University of Pavia, Via Bassi 6, Pavia (Italy); National Institute of Nuclear Physics (INFN), Section of Pavia, Via Bassi 6, Pavia (Italy); Bruschi, P.; Chiari, P.; Fossati, F.; Stella, S. [Department of Nuclear and Theoretical Physics, University of Pavia, Via Bassi 6, Pavia (Italy); Prati, U.; Roveda, L. [Unit of cancer surgery, Cancer Center of Excellence, Foundation T. Campanella, Catanzaro (Italy); Zonta, A.; Zonta, C.; Ferrari, C.; Clerici, A. [Department of Surgery, University of Pavia, Piazza Botta, Pavia (Italy); Nano, R. [Department of Animal Biology, University of Pavia, Piazza Botta, Pavia (Italy); Pinelli, T. [Department of Nuclear and Theoretical Physics, University of Pavia, Via Bassi 6, Pavia (Italy); National Institute of Nuclear Physics (INFN), Section of Pavia, Via Bassi 6, Pavia (Italy)

    2008-12-15

    The ability to selectively hit the tumour cells is an essential characteristic of an anti-tumour therapy. In boron neutron capture therapy (BNCT) this characteristic is based on the selective uptake of {sup 10}B in the tumour cells with respect to normal tissues. An important step in the BNCT planning is the measurement of the boron concentration in the tissue samples, both tumour and healthy. When the tumour is spread through the healthy tissue, as in the case of metastases, the knowledge of the different kinds of tissues in the sample being analysed is crucial. If the percentage of tumour and normal tissues cannot be evaluated, the obtained concentration is a mean value depending on the composition of the different samples being measured. In this case an imaging method that could give information both on the morphology and on the spatial distribution of boron concentration in the sample would be a fundamental support. In this paper, the results of the boron uptake analysis in the tumour and in the healthy samples taken from human livers after boron phenylalanine (BPA) infusion are shown; boron imaging was performed using neutron autoradiography.

  15. Fluoride Uptake Profiles of Selected European Toothpastes into Hard Tissues and Plaque.

    Science.gov (United States)

    Moore, Joel; Schneiderman, Eva; Farmer, Teresa; Zsiska, Marianne

    2017-09-01

    To compare the fluoridating potential of selected European toothpastes using a combination of enamel, dentin, and plaque in vitromodels. Four in vitromodels were included: 1) Enamel Fluoride (F) Uptake (EFU); 2) Dentin F Uptake (DFU); 3) Enamel Solubility Reduction (ESR); and 4) Plaque F Uptake (PFU). A core set of marketed products was included in all studies, plus a standard toothpaste (1100 ppm F as NaF/silica) and placebo control (the PFU study did not include a placebo control). Test dentifrices: [A] Fluocaril® Bi-Fluoré 250 (1500 ppm F as NaF+1000 ppm F as SMFP); [B] LacerAnticaries (2500 ppm F as SMFP); [C] Elmex® Caries Professional™ (1450 ppm F as SMFP+1.5% arginine); [D] Colgate® Triple Action (1450 ppm F as SMFP); [E] Placebo (0 ppm F); and [F] standard toothpaste (1100 ppm as NaF/silica). In all studies (EFU, DFU, ESR, and PFU), assessments were compared for each pair using the Tukey-Kramer HSD test (p F = B = C = D > E; DFU: A > F = B = C = D = E; PFU: A = B > F = C = D). In demineralization prevention, the Fluocaril dentifrice [A] also provided the greatest benefit (ESR: A = F = C = B = D > E). In all studies that included a placebo control, all of the F-containing dentifrices performed better than the placebo control. While these results demonstrate that all of the marketed products tested provide effective anticaries benefits, the Fluocaril Bi-Fluoré 250 dentifrice consistently delivered unsurpassed performance. It delivered the highest level of F to plaque, provided greater measures of efficacy in both remineralization and inhibition of demineralization, and delivered substantial improvement in fluoridation of dentin, suggesting the potential for delivering both coronal and root caries benefits.

  16. Enantio-selective molecular dynamics of (±)-o,p-DDT uptake and degradation in water-sediment system.

    Science.gov (United States)

    Ali, Imran; Alharbi, Omar M L; Alothman, Zeid A; Alwarthan, Abdulrahman

    2018-01-01

    Enantio-selective molecular dynamics of (±)-o,p-DDT uptake and degradation in water-sediment system is described. Both uptake and degradation processes of (-)-o,p-DDT were slightly higher than (+)-o,p-DDT enantiomer. The optimized parameters for uptake were 7.0μgL -1 concentration of o,p-DDT, 60min contact time, 5.0pH, 6.0gL -1 amount of reverine sediment and 25°C temperature. The maximum degradation of both (-)- and (+)-o,p-DDT was obtained with 16 days, 0.4μgL -1 concentration of o,p-DDT, pH 7 and 35°C temperature. Both uptake and degraded process followed first order rate reaction. Thermodynamic parameters indicated exothermic nature of uptake and degradation processes. Both uptake and degradation were slightly higher for (-)-enantiomer in comparison to (+)-enantiomer of o,p-DDT. It was concluded that both uptake and degradation processes are responsible for the removal of o,p-DDT from nature but uptake plays a crucial role. The percentage degradations of (-)- and (+)-o,p-DDT were 30.1 and 29.5, respectively. This study may be useful to manage o,p-DDT contamination of our earth's ecosystem. Copyright © 2017. Published by Elsevier Inc.

  17. Thermal properties of selected cheeses samples

    Directory of Open Access Journals (Sweden)

    Monika BOŽIKOVÁ

    2016-02-01

    Full Text Available The thermophysical parameters of selected cheeses (processed cheese and half hard cheese are presented in the article. Cheese is a generic term for a diverse group of milk-based food products. Cheese is produced throughout the world in wide-ranging flavors, textures, and forms. Cheese goes during processing through the thermal and mechanical manipulation, so thermal properties are one of the most important. Knowledge about thermal parameters of cheeses could be used in the process of quality evaluation. Based on the presented facts thermal properties of selected cheeses which are produced by Slovak producers were measured. Theoretical part of article contains description of cheese and description of plane source method which was used for thermal parameters detection. Thermophysical parameters as thermal conductivity, thermal diffusivity and volume specific heat were measured during the temperature stabilisation. The results are presented as relations of thermophysical parameters to the temperature in temperature range from 13.5°C to 24°C. Every point of graphic relation was obtained as arithmetic average from measured values for the same temperature. Obtained results were statistically processed. Presented graphical relations were chosen according to the results of statistical evaluation and also according to the coefficients of determination for every relation. The results of thermal parameters are in good agreement with values measured by other authors for similar types of cheeses.

  18. Influence of physicochemical properties of rice flour on oil uptake of tempura frying batter.

    Science.gov (United States)

    Nakamura, Sumiko; Ohtsubo, Ken'ichi

    2010-01-01

    The physicochemical properties of rice flour and wheat flour influenced the oil uptake of tempura frying batter. Rice flour was better than wheat flour in the overall quality and crispness of the fried tempura batter. Rice flour resisted oil absorption more than wheat flour, and a higher level of apparent starch amylose and higher consistency/breakdown ratio of the pasting properties led to a lower oil uptake of the batter. Super hard EM10 rice showed the highest apparent amylose content and higher consistency/breakdown ratio than the other flour samples, the batter from EM10 revealing the lowest oil content after frying among all the batters examined. The apparent amylose content, consistency/breakdown ratio and oil absorption index are proposed as useful guides for oil absorption when frying from among the physicochemical properties that influence the oil content of fried batter. Our proposal for the "oil absorption index" could be a simple, although not perfect method for estimating the oil content of batter flour.

  19. Selective uptake of p-boronophenylalanine by osteosarcoma cells for boron neutron capture therapy

    Energy Technology Data Exchange (ETDEWEB)

    Ferrari, C. [Department of Surgery, Experimental Surgery Laboratory, University of Pavia, Piazza Botta, Pavia (Italy)], E-mail: ferraric@unipv.it; Zonta, C.; Cansolino, L.; Clerici, A.M.; Gaspari, A. [Department of Surgery, Experimental Surgery Laboratory, University of Pavia, Piazza Botta, Pavia (Italy); Altieri, S.; Bortolussi, S.; Stella, S. [Department of Nuclear and Theoretical Physics of University, Via Bassi, 6, Pavia (Italy); National Institute of Nuclear Physics (INFN) Section of Pavia, Via Bassi, 6, Pavia (Italy); Bruschi, P. [Department of Nuclear and Theoretical Physics of University, Via Bassi, 6, Pavia (Italy); Dionigi, P.; Zonta, A. [Department of Surgery, Experimental Surgery Laboratory, University of Pavia, Piazza Botta, Pavia (Italy)

    2009-07-15

    Osteosarcoma is the most common non-hematologic primary cancer type that develops in bone. Current osteosarcoma treatments combine multiagent chemotherapy with extensive surgical resection, which in some cases makes necessary the amputation of the entire limb. Nevertheless its infiltrative growth leads to a high incidence of local and distant recurrences that reduce the percentage of cured patients to less than 60%. These poor data required to set up a new therapeutic approach aimed to restrict the surgical removal meanwhile performing a radical treatment. Boron neutron capture therapy (BNCT), a particular radiotherapy based on the nuclear capture and fission reactions by atoms of {sup 10}B, when irradiated with thermal neutrons, could be a valid alternative or integrative option in case of osteosarcoma management, thanks to its peculiarity in selectively destroying neoplastic cells without damaging normal tissues. Aim of the present work is to investigate the feasibility of employing BNCT to treat the limb osteosarcoma. Boronophenylalanine (BPA) is used to carry {sup 10}B inside the neoplastic cells. As a first step the endocellular BPA uptake is tested in vitro on the UMR-106 osteosarcoma cell line. The results show an adequate accumulation capability. For the in vivo experiments, an animal tumor model is developed in Sprague-Dawley rats by means of an intrafemoral injection of UMR-106 cells at the condyle site. The absolute amounts of boron loading and the tumor to normal tissue {sup 10}B ratio are evaluated 2 h after the i.v. administration of BPA. The boron uptake by the neoplastic tissue is almost twice the normal one. However, higher values of boron concentration in tumor are requested before upholding BNCT as a valid therapeutic option in the treatment of osteosarcoma.

  20. Targeting dendritic cells through gold nanoparticles: A review on the cellular uptake and subsequent immunological properties.

    Science.gov (United States)

    Ahmad, Suhana; Zamry, Anes Ateqah; Tan, Hern-Tze Tina; Wong, Kah Keng; Lim, JitKang; Mohamud, Rohimah

    2017-11-01

    Gold nanoparticles (NPs) have been proposed as a highly potential tool in immunotherapies due to its advantageous properties including customizable size and shapes, surface functionality and biocompatibility. Dendritic cells (DCs), the sentinels of immune response, have been of interest to be manipulated by using gold NPs for targeted delivery of immunotherapeutic agent. Researches done especially in human DCs showed a variation of gold NPs effects on cellular uptake and internalization, DC maturation and subsequent T cells priming as well as cytotoxicity. In this review, we describe the synthesis and physiochemical properties of gold NPs as well as the importance of gold NPs in immunotherapies through their actions on human DCs. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  1. Synthesis of 14C- and 3H-labeled fluoxetine, a selective serotonin uptake inhibitor

    International Nuclear Information System (INIS)

    Robertson, D.W.; Krushinski, J.H.; Wong, D.T.; Kau, D.

    1987-01-01

    Fluoxetine (N-methyl-γ-(4-(trifluoromethyl)phenoxy) benzenepropanamine) is a potent, highly selective serotonin uptake inhibitor that is useful in treating a variety of major psychiatric derangements. We have synthesized this compound in 14 C- and 3 H-labeled forms. The tritium label was introduced in the final step by catalytic dehalogenation of the brominated fluoxetine precursor. Reaction conditions could be controlled such that catalytic hydrogenolysis of the labile C-O benzylic bond was minimized. Following HPLC purification, [ 3 H]-fluoxetine was obtained in a state of high radiochemical purity (98%) and specific activity (20.4 Ci/mmol). The 14 C-label was introduced in the final step via a nucleophilic aromatic substitution reaction between the sodium salt of α-(2-(methylamino)ethyl)benzenemethanol and uniformly ring-labeled p-chlorobenzotrifluoride. Following purification by flash chromatography, [ 14 C]-fluoxetine was obtained in 98.3% radiochemical purity with a specific activity of 5.52 mCi/mmol. (author)

  2. Stone-ground wood pulp-reinforced polypropylene composites: Water uptake and thermal properties

    Directory of Open Access Journals (Sweden)

    Joan Pere López

    2012-11-01

    Full Text Available Two of the drawbacks of using natural-based composites in industrial applications are thermal instability and water uptake capacity. In this work, mechanical wood pulp was used to reinforce polypropylene at a level of 20 to 50 wt. %. Composites were mixed by means of a Brabender internal mixer for both non-coupled and coupled formulations. Differential scanning calorimetry (DSC and thermogravimetric analysis (TGA were used to determine the thermal properties of the composites. The water uptake behavior was evaluated by immersion of the composites in water until an equilibrium state was reached. Results of water absorption tests revealed that the amount of water absorption was clearly dependent upon the fiber content. The coupled composites showed lower water absorption compared to the uncoupled composites. The incorporation of mechanical wood pulp into the polypropylene matrix produced a clear nucleating effect by increasing the crystallinity degree of the polymer and also increasing the temperature of polymer degradation. The maximum degradation temperature for stone ground wood pulp–reinforced composites was in the range of 330 to 345 ºC.

  3. In vivo regulation of scavenger receptor BI and the selective uptake of high density lipoprotein cholesteryl esters in rat liver parenchymal and Kupffer cells

    NARCIS (Netherlands)

    Fluiter, K.; van der Westhuijzen, D. R.; van Berkel, T. J.

    1998-01-01

    High density lipoprotein cholesteryl esters (HDL-CE) are selectively taken up by liver parenchymal cells without parallel apolipoprotein uptake. This selective uptake route forms an important step in the so-called reverse cholesterol transport. Scavenger receptor BI (SR-BI) is the only known HDL

  4. Endocytic pathways involved in PLGA nanoparticle uptake by grapevine cells and role of cell wall and membrane in size selection.

    Science.gov (United States)

    Palocci, Cleofe; Valletta, Alessio; Chronopoulou, Laura; Donati, Livia; Bramosanti, Marco; Brasili, Elisa; Baldan, Barbara; Pasqua, Gabriella

    2017-12-01

    PLGA NPs' cell uptake involves different endocytic pathways. Clathrin-independent endocytosis is the main internalization route. The cell wall plays a more prominent role than the plasma membrane in NPs' size selection. In the last years, many studies on absorption and cell uptake of nanoparticles by plants have been conducted, but the understanding of the internalization mechanisms is still largely unknown. In this study, polydispersed and monodispersed poly(lactic-co-glycolic) acid nanoparticles (PLGA NPs) were synthesized, and a strategy combining the use of transmission electron microscopy (TEM), confocal analysis, fluorescently labeled PLGA NPs, a probe for endocytic vesicles (FM4-64), and endocytosis inhibitors (i.e., wortmannin, ikarugamycin, and salicylic acid) was employed to shed light on PLGA NP cell uptake in grapevine cultured cells and to assess the role of the cell wall and plasma membrane in size selection of PLGA NPs. The ability of PLGA NPs to cross the cell wall and membrane was confirmed by TEM and fluorescence microscopy. A strong adhesion of PLGA NPs to the outer side of the cell wall was observed, presumably due to electrostatic interactions. Confocal microscopy and treatment with endocytosis inhibitors suggested the involvement of both clathrin-dependent and clathrin-independent endocytosis in cell uptake of PLGA NPs and the latter appeared to be the main internalization pathway. Experiments on grapevine protoplasts revealed that the cell wall plays a more prominent role than the plasma membrane in size selection of PLGA NPs. While the cell wall prevents the uptake of PLGA NPs with diameters over 50 nm, the plasma membrane can be crossed by PLGA NPs with a diameter of 500-600 nm.

  5. Soil Chemical Properties and Nutrient Uptake of Cocoa as Affected by Application of Different Organic Matters and Phosphate Fertilizers

    Directory of Open Access Journals (Sweden)

    Sugiyanto Sugiyanto

    2008-07-01

    Full Text Available Effort repair of land quality better be done by simultan namely with application of organic matters and inorganic fertilization. The objective of this research is to study the effect of varied organic matters source and phosphate fertilizers on the chemicals soil characteristic and cocoa nutrient uptake. The experiment was laid experimentally in split-plot design and environmentally in randomized complete block design. The main plot was source of P consisted of, control, SP 36 and rock phosphate in dosage of 200 mg P2O5 per kg of air dry soil. Source of organic matter as sub-plot consisted of control (no organic matter, cow dung, cocoa pod husk compost and sugar cane filter cake, each in dosage of 2.5 and 5.0%. Result of this experiment showed application of cow dung, cocoa pod husk compost and sugar cane filter cake increased content of C, N, Ca exchangeable, Fe available, and pH in soil, and SP 36 increased availability of P in soil. Application of sugar cane filter cake increased N, K, Ca, Mg, and SO4 uptake but did not increase Cl uptake, application of cow dung in dosage 5% increased N, K, and Cl uptake and cocoa pod husk compost dosage 5% increased N and K uptake of cocoa. SP 36 increased Mg uptake of cocoa but rock phosphate did not increase it. They were not interaction between organic matters and phosphate fertilizers to nutrient uptake of cocoa. Nutrient soil content as affected by organic matters correlated with nutrient uptake of cocoa.Key words : soil chemical properties, nutrient uptake, cocoa, organic matter, phosphate fertlizers.

  6. Selected mechanical properties of modified beech wood

    Directory of Open Access Journals (Sweden)

    Jiří Holan

    2008-01-01

    Full Text Available This thesis deals with an examination of mechanical properties of ammonia treated beach wood with a trademark Lignamon. For determination mechanical properties were used procedures especially based on ČSN. From the results is noticeable increased density of wood by 22% in comparison with untreated beach wood, which makes considerable increase of the most mechanical wood properties. Considering failure strength was raised by 32% and modulus of elasticity was raised at average about 46%.

  7. Properties and selection criteria for adsorbents

    International Nuclear Information System (INIS)

    Wirth, H.

    1976-01-01

    The paper gives a survey of the most important industrial adsorbents and of their suitability for different purposes. With special consideration of activated carbon, the properties and characteristic data are discussed which are used for assessing adsorbents. These, among other things, are as follows: specific surface area, pore size distribution, adsorption isotherms, hydrophobic properties, catalytic properties, chemical resistance, heat resistance, particle size and hardness. (orig.) [de

  8. Prediction of cesium-134 and strontium-85 crop uptake based on soil properties

    International Nuclear Information System (INIS)

    Roca, M.C.; Vallejo, V.R.; Roig, M.; Tent, J.; Vidal, M.; Rauret, G.

    1997-01-01

    Nowadays, there is still the need to improve the quantification of parameters that affect radionuclide mobility. With this aim, radiocesium and radiostrontium soil-to-plant transfer was measured in lysimeters in a Calcic Luvisol, loamy soil and in a Fluvisol, loam-sandy soil, using lettuce [Lactuca sativa L. cv. Kinemontepas] and pea plants [Pisum sativum L. cv. Kelvedon Wonder]. Weighted Concentration Ratios (WCR), expressed as kg soil/kg plant, were calculated for different growth stages. Weighted Concentration Ratios were in general higher for 85Sr than for 134Cs, and also higher in the loam-sandy than in the loamy soil. To predict plant uptake, we evaluated a set of soil properties to define a prediction factor for the relative transfer in the two soils using cation exchange capacity (CEC) and radionuclide available fraction (fav) for radiostrontium, and soil solution composition, solid-liquid distribution coefficient, and radionuclide available fraction for radiocesium. The ratios of WCR in the loam-sandy and loamy soil were compared with the prediction factor. There was good agreement in lettuce for 85Sr (ratio of WCR was 5.4 for seedling and 3.9 for commercial samples, whereas prediction factor was 3.1) and for 134Cs (ratio of WCR was 5.1 for seedling and 5.5 for commercial samples, the prediction factor being 5.1), although for pea only the relative root uptake of radiocesium in seedling pea was well predicted (the ratio of WCR was 8.8, the prediction factor being 9.1). These soil parameters improved former predictions based solely on the fav, although factors depending on plant physiology should be better evaluated

  9. The market dynamics of selective serotonin re-uptake inhibitors: a ...

    African Journals Online (AJOL)

    re-uptake inhibitors: a private sector study in South Africa. Afri Health ... the public and private sectors to reduce medicine costs, and increase ... Fig 1: Comparison between the market volume of generics vs. originators for the period June 2009 ...

  10. Uptake of selected organics and metals by terrestrial vegetation and insects at a site in Arizona

    International Nuclear Information System (INIS)

    Day, C.H.; Ayers, T.A.; Ellingson, S.B.; Braddy, L.

    1995-01-01

    As part of an investigation at a CERCLA site in Arizona, 27 potential sources of contamination (PSCS) were identified for study. A screening level ecological risk assessment was conducted for each PSC using generic plant uptake factors and conservative exposure parameters. Risk estimates were calculated for the indicator species using the hazard index (HI) approach. Results of the screening level assessment indicated that 4 of the 27 PSCs required further evaluation due to elevated HIs. The contaminants of potential concern (COPCS) are antimony, cadmium, lead, polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), and total petroleum hydrocarbons (TPH). A field sampling program at the 4 PSCs and a site-specific background location was conduct4ed to collect the food sources for the indicator species. The samples have been analyzed for the COPCs and the results are being used to validate the screening level risk calculations. The site-specific soil-to-plant uptake factors will be compared to generic soil-to-plant uptake factors obtained from the scientific literature, with emphasis placed on studies done in similar arid environments. Contaminant-specific soil-to-insect bioaccumulation factors (BAFs) will be presented and compared to BAFs derived using published bioaccumulation models

  11. A high surface area Zr(IV)-based metal–organic framework showing stepwise gas adsorption and selective dye uptake

    Energy Technology Data Exchange (ETDEWEB)

    Lv, Xiu-Liang [Beijing Key Laboratory for Green Catalysis and Separation, Department of Chemistry and Chemical Engineering, Beijing University of Technology, Beijing 100124 (China); Tong, Minman; Huang, Hongliang [College of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Wang, Bin; Gan, Lei [Beijing Key Laboratory for Green Catalysis and Separation, Department of Chemistry and Chemical Engineering, Beijing University of Technology, Beijing 100124 (China); Yang, Qingyuan [College of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zhong, Chongli [College of Chemical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); State Key Laboratory of Organic–Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Li, Jian-Rong, E-mail: jrli@bjut.edu.cn [Beijing Key Laboratory for Green Catalysis and Separation, Department of Chemistry and Chemical Engineering, Beijing University of Technology, Beijing 100124 (China); State Key Laboratory of Organic–Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China)

    2015-03-15

    Exploitation of new metal–organic framework (MOF) materials with high surface areas has been attracting great attention in related research communities due to their broad potential applications. In this work, a new Zr(IV)-based MOF, [Zr{sub 6}O{sub 4}(OH){sub 4}(eddb){sub 6}] (BUT-30, H{sub 2}eddb=4,4′-(ethyne-1,2-diyl)dibenzoic acid) has been solvothermally synthesized, characterized, and explored for gases and dyes adsorptions. Single-crystal X-ray diffraction analysis demonstrates a three-dimensional cubic framework structure of this MOF, in which each Zr{sub 6}O{sub 4}(OH){sub 4} building unit is linked by 12 linear eddb ligands. BUT-30 has been found stable up to 400 °C and has a Brunauer–Emmett–Teller (BET) surface area as high as 3940.6 m{sup 2} g{sup −1} (based on the N{sub 2} adsorption at 77 K) and total pore volume of 1.55 cm{sup 3} g{sup −1}. It is more interesting that this MOF exhibits stepwise adsorption behaviors for Ar, N{sub 2}, and CO{sub 2} at low temperatures, and selective uptakes towards different ionic dyes. - Graphical abstract: A new Zr(IV)-based MOF with high surface area has been synthesized and structurally characterized, which shows stepwise gas adsorption at low temperature and selective dye uptake from solution. - Highlights: • A new Zr-based MOF was synthesized and structurally characterized. • This MOF shows a higher surface area compared with its analogous UiO-67 and 68. • This MOF shows a rare stepwise adsorption towards light gases at low temperature. • This MOF performs selective uptakes towards cationic dyes over anionic ones. • Using triple-bond spacer is confirmed feasible in enhancing MOF surface areas.

  12. Selective uptake of a toxic lipophilic anthracycline derivative by the low-density lipoprotein receptor pathway in cultured fibroblasts

    International Nuclear Information System (INIS)

    Vitols, S.G.; Masquelier, M.; Peterson, C.O.

    1985-01-01

    N-(N-Retinoyl)-L-leucyldoxorubicin 14-linoleate (r11-DOX), a new lipophilic derivative of doxorubicin, was synthesized and incorporated into low-density lipoprotein (LDL). The drug-LDL complex contained 100- 200 drug molecules/LDL particle. When cultured normal human fibroblasts were incubated with 125 I-LDL-incorporated drug, there was a perfect correlation between the cellular uptake plus degradation of 125 I-LDL and the cellular drug accumulation. The presence of excess native LDL inhibited the cellular uptake and degradation of 125 I-LDL and the drug accumulation to the same extent. In contrast, methylated LDL, which does not bind to the LDL receptor, did not alter the cellular uptake and degradation of 125 I-LDL nor did it alter the drug accumulation. When LDL receptor negative fibroblasts from a patient with the homozygous form of familial hypercholesterolemia were incubated with the drug- 125 I-LDL complex, cellular drug accumulation was very low. The drug-LDL complex inhibited the growth of cultured normal human fibroblasts. The drug incorporated into methylated LDL was much less toxic. These findings suggest that r11-DOX incorporated into LDL is delivered to cells selectively by the LDL receptor pathway. This might be of value in the treatment of leukemia, since it has been previously found that leukemic cells exhibit higher LDL receptor activity than white blood cells and bone marrow cells from healthy subjects

  13. Behavioral and biochemical effects of the antidepressant bupropion (Wellbutrin): evidence for selective blockade of dopamine uptake in vivo.

    Science.gov (United States)

    Cooper, B R; Hester, T J; Maxwell, R A

    1980-10-01

    Bupropion (BW 323U; Wellbutrin), a novel compound with antidepressant effects in man, was found to reduce immobility in an "experimental helplessness" forced swimming antidepressant test in rats as did imipramine and amitriptyline. Higher doses produced elevated locomotor activity in an automated open field and produced stereotyped sniffing which was contrasted with apomorphine. When bupropion or desmethylimipramine was given before intracisternal injections of 6-hydroxydopamine, bupropion produced a dose-related selective antagonism of the destruction of dopamine neurons, while under the same conditions, desmethylimipramine produced a dose-related selective antagonism of the destruction of noradrenergic neurons. Studies in which the dose of bupropion and the dose of 6-hydroxydopamine were varied revealed that a dose-related selective antagonism of dopamine depletion by 6-hydroxydopamine occurred when doses up to and including 50 mg/kg i.p. to bupropion were administered. Some antagonism of norepinephrine depletion also occurred at 100 mg/kg of bupropion i.p. Bupropion also selectively reversed the dopamine depletion produced by alpha-methyl-m-tyrosine, a finding which is consistent with the view that bupropion is a dopamine uptake inhibitor in vivo. The importance of dopamine systems for the behavioral effects of bupropion were also studied. When the locomotor stimulant effects of bupropion were tested in rats with chronic destruction of dopamine neurons produced by 6-hydroxydopamine, bupropion failed to elevate locomotor activity. Rats treated with procedures using 6-hydroxydopamine to produce relatively selective norepinephrine depletions responded to bupropion with locomotor activity stimulation like controls. Rats with similar depletions of either dopamine or norepinephrine were also tested for the ability of low doses of bupropion to reduce immobility in the "experimental helplessness" forced swim antidepressant test. Prior destruction of dopamine neurons

  14. Radionuclide movement in soils and uptake by plants. A selected, annotated bibliography

    International Nuclear Information System (INIS)

    Francis, C.W.; Talmage, S.S.; McMullin, B.B.

    1975-08-01

    This bibliography covers the world literature from 1948 to 1975 and contains 1397 references to information on how various chemical, physical, and biological factors influence the movement of radionuclides in soil and uptake by plants. Much of the data is related to the major fission products in radioactive fallout, with emphasis on 137 Cs and 90 Sr. References are included to data on nearly all fission products, a large number of biologically important activation products, and various naturally occurring radioactive nuclides such as uranium and thorium. Subject, author, geographic location, taxon, and permuted title indexes are included. (U.S.)

  15. Lack of detectable DNA uptake by transmission of selected recipients in mono-associated rats

    DEFF Research Database (Denmark)

    Wilcks, Andrea; Jacobsen, Bodil B. L.

    2010-01-01

    for the construction of GM plants end up in pathogenic bacteria, eventually leading to untreatable disease. Three different bacterial species (Escherichia coli, Bacillus subtilis, Streptococcus gordonii), all natural inhabitants of the food and intestinal tract environment were used as recipients for uptake of DNA...... than the consumption of GM food harbouring antibiotic resistance genes.......An important concern revealed in the public discussion of the use of genetically modified (GM) plants for human consumption, is the potential transfer of DNA from these plants to bacteria present in the gastrointestinal tract. Especially, there is a concern that antibiotic resistance genes used...

  16. Selected physical properties of various diesel blends

    Science.gov (United States)

    Hlaváčová, Zuzana; Božiková, Monika; Hlaváč, Peter; Regrut, Tomáš; Ardonová, Veronika

    2018-01-01

    The quality determination of biofuels requires identifying the chemical and physical parameters. The key physical parameters are rheological, thermal and electrical properties. In our study, we investigated samples of diesel blends with rape-seed methyl esters content in the range from 3 to 100%. In these, we measured basic thermophysical properties, including thermal conductivity and thermal diffusivity, using two different transient methods - the hot-wire method and the dynamic plane source. Every thermophysical parameter was measured 100 times using both methods for all samples. Dynamic viscosity was measured during the heating process under the temperature range 20-80°C. A digital rotational viscometer (Brookfield DV 2T) was used for dynamic viscosity detection. Electrical conductivity was measured using digital conductivity meter (Model 1152) in a temperature range from -5 to 30°C. The highest values of thermal parameters were reached in the diesel sample with the highest biofuel content. The dynamic viscosity of samples increased with higher concentration of bio-component rapeseed methyl esters. The electrical conductivity of blends also increased with rapeseed methyl esters content.

  17. Selective intra-arterial administration of {sup 18}F-FDG to the rat brain - effects on hemispheric uptake

    Energy Technology Data Exchange (ETDEWEB)

    Arnberg, Fabian; Samen, Erik; Lundberg, Johan; Grafstroem, Jonas; Soederman, Michael; Stone-Elander, Sharon; Holmin, Staffan [Karolinska Institutet, Department of Clinical Neuroscience, Stockholm (Sweden); Karolinska University Hospital-Solna, Department of Neuroradiology, Stockholm (Sweden); Lu, Li [Karolinska University Hospital-Solna, KERIC, Stockholm (Sweden)

    2014-05-15

    The purpose of this study was to investigate the radioligand uptake and iodine contrast distribution in the intra- and extracranial circulation of the rat, after intra-arterial injections to the common carotid artery and different parts of the internal carotid artery. All animal experiments were carried out in accordance with Karolinska Institutet's guidelines and were approved by the local laboratory animal ethics committee. We used clinical neurointerventional systems to place microcatheters in the extra- or intracranial carotid artery of 15 Sprague-Dawley rats. Here, injection dynamics of iodine contrast was assessed using digital subtraction angiography. Maintaining the catheter position, the animals were placed in a micro PET and small-animal positron emission tomography (PET) was used to analyze injections [2-{sup 18}F]-2-fluoro-2-deoxy-d-glucose ({sup 18}F-FDG). Microcatheters had to be placed in the intracranial carotid artery (iICA) for the infusate to distribute to the brain. Selective injection via the iICA resulted in a 9-fold higher uptake of {sup 18}F-FDG in the injected hemisphere (p < 0.005) compared to both intravenous and more proximal carotid artery injections. Furthermore, selective injection gave a dramatically improved contrast between the brain and extracranial tissue. Intra-arterial injection increases the cerebral uptake of a radiotracer dramatically compared to systemic injection. This technique has potential applications for endovascular treatment of malignancies allowing intra-interventional modifications of injection strategy, based on information on tumor perfusion and risk to surrounding normal parenchyma. Furthermore the technique may increase diagnostic sensitivity and avoid problems due to peripheral pharmacological barriers and first passage metabolism of labile tracers. (orig.)

  18. Selective intra-arterial administration of 18F-FDG to the rat brain - effects on hemispheric uptake

    International Nuclear Information System (INIS)

    Arnberg, Fabian; Samen, Erik; Lundberg, Johan; Grafstroem, Jonas; Soederman, Michael; Stone-Elander, Sharon; Holmin, Staffan; Lu, Li

    2014-01-01

    The purpose of this study was to investigate the radioligand uptake and iodine contrast distribution in the intra- and extracranial circulation of the rat, after intra-arterial injections to the common carotid artery and different parts of the internal carotid artery. All animal experiments were carried out in accordance with Karolinska Institutet's guidelines and were approved by the local laboratory animal ethics committee. We used clinical neurointerventional systems to place microcatheters in the extra- or intracranial carotid artery of 15 Sprague-Dawley rats. Here, injection dynamics of iodine contrast was assessed using digital subtraction angiography. Maintaining the catheter position, the animals were placed in a micro PET and small-animal positron emission tomography (PET) was used to analyze injections [2- 18 F]-2-fluoro-2-deoxy-d-glucose ( 18 F-FDG). Microcatheters had to be placed in the intracranial carotid artery (iICA) for the infusate to distribute to the brain. Selective injection via the iICA resulted in a 9-fold higher uptake of 18 F-FDG in the injected hemisphere (p < 0.005) compared to both intravenous and more proximal carotid artery injections. Furthermore, selective injection gave a dramatically improved contrast between the brain and extracranial tissue. Intra-arterial injection increases the cerebral uptake of a radiotracer dramatically compared to systemic injection. This technique has potential applications for endovascular treatment of malignancies allowing intra-interventional modifications of injection strategy, based on information on tumor perfusion and risk to surrounding normal parenchyma. Furthermore the technique may increase diagnostic sensitivity and avoid problems due to peripheral pharmacological barriers and first passage metabolism of labile tracers. (orig.)

  19. Design of hypoxia-targeting radiopharmaceuticals: selective uptake of copper-64 complexes in hypoxic cells in vitro

    International Nuclear Information System (INIS)

    Dearling, J.L.J.; Lewis, J.S.; Mullen, G.E.D.; Rae, M.T.; Zweit, J.; Blower, P.J.

    1998-01-01

    The well-known perfusion tracer CuPTSM, labelled with 62 Cu or 64 Cu, is believed to be trapped in cells non-selectively by a bioreductive mechanism. It is proposed that by modifying the ligand to increase its electron donor strength (for example by adding alkyl functionality or replacing sulphur ligands with oxygen ligands), the copper complexes will become less easily reduced and tracers with selectivity for hypoxic tissues could thus be developed. The aim of this work was to prepare 64 Cu-labelled complexes of two series of ligands, based on the bis(thiosemicarbazone) (13 ligands) and bis(salicylaldimine) (3 ligands) skeletons, and to evaluate the hypoxia dependence of their uptake in cells. The complexes were incubated with Chinese hamster ovary cells under normoxic and hypoxic conditions, and the cells isolated by centrifugation to determine radioactivity uptake at various time points up to 90 min. Several members of both series demonstrated significant (P 60 Cu, 61 Cu, 62 Cu, 64 Cu) and targeted radiotherapy ( 64 Cu, 67 Cu). (orig.)

  20. Selective chemical binding enhances cesium tolerance in plants through inhibition of cesium uptake.

    Science.gov (United States)

    Adams, Eri; Chaban, Vitaly; Khandelia, Himanshu; Shin, Ryoung

    2015-03-05

    High concentrations of cesium (Cs(+)) inhibit plant growth but the detailed mechanisms of Cs(+) uptake, transport and response in plants are not well known. In order to identify small molecules with a capacity to enhance plant tolerance to Cs(+), chemical library screening was performed using Arabidopsis. Of 10,000 chemicals tested, five compounds were confirmed as Cs(+) tolerance enhancers. Further investigation and quantum mechanical modelling revealed that one of these compounds reduced Cs(+) concentrations in plants and that the imidazole moiety of this compound bound specifically to Cs(+). Analysis of the analogous compounds indicated that the structure of the identified compound is important for the effect to be conferred. Taken together, Cs(+) tolerance enhancer isolated here renders plants tolerant to Cs(+) by inhibiting Cs(+) entry into roots via specific binding to the ion thus, for instance, providing a basis for phytostabilisation of radiocesium-contaminated farmland.

  1. Thermophysical properties of selected wear-resistant alloys

    International Nuclear Information System (INIS)

    Farwick, D.G.; Johnson, R.N.

    1980-06-01

    Thermophysical properties of 13 selected wear-resistant materials, including specific heat, thermal conductivity, thermal diffusivity, and thermal expansion (instantaneous, mean, and linear) are provided. The Center for Information and Numerical Data Analysis and Synthesis (CINDAS) at Purdue University supplied properties data

  2. Physical Property Control on the Cellular Uptake Pathway and Spatial Distribution of Nanoparticles in Cells.

    Science.gov (United States)

    Ahn, Sungsook; Seo, Eunseok; Kim, Ki Hean; Lee, Sang Joon

    2015-06-01

    Nanoparticles have been developed in broad biomedical research in terms of effective cellular interactions to treat and visualize diseased cells. Considering the charge and polar functional groups of proteins that are embedded in cellular membranes, charged nanoparticles have been strategically developed to enhance electrostatic cellular interactions. In this study, we show that cellular uptake efficiency, pathway, and spatial distribution of gold nanoparticles in a cell are significantly modulated based on the surface condition of gold nanoparticles and human cancer cells that were tuned by controlling the pH of the medium and by introducing an electron beam. Cellular uptake efficiency is increased when electrostatic attraction is induced between the cells and the gold nanoparticles. Cell surface modification changes the cellular uptake pathways of the gold nanoparticles and concentrates the gold nanoparticles at the membrane region. Surface modification of the gold nanoparticles also contributes to deep penetration and homogeneous spatial distributions in a cell.

  3. Impacts of industrial waste resources on maize (Zea mays L.) growth, yield, nutrients uptake and soil properties.

    Science.gov (United States)

    Singh, Satnam; Young, Li-Sen; Shen, Fo-Ting; Young, Chiu-Chung

    2014-10-01

    Discharging untreated highly acidic (pH10.0) paper-mill wastewater (PW) causes environmental pollution. When acidity of MW neutralized (pH 6.5±0.1) with PW and lime (treatments represented as MW+PW and MW+Lime), then MW may be utilized as a potential source of nutrients and organic carbon for sustainable food production. Objectives of this study were to compare the effects of PW and lime neutralized MW and chemical fertilizers on maize (Zea mays L. cv. Snow Jean) plant growth, yield, nutrients uptake, soil organic matter and humic substances. The field experiment was carried out on maize using MW at 6000 L ha(-1). Impacts of the MW application on maize crop and soil properties were evaluated at different stages. At harvest, plant height, and plant N and K uptake were higher in MW treatment. Leaf area index at 60 days after sowing, plant dry matter accumulation at harvest, and kernels ear(-1) and 100-kernel weight were higher in MW+Lime treatment. Kernel N, P, K, Mn, Fe and Zn, and plant Zn uptake were highest in MW+Lime. Plant Fe uptake, and soil organic matter and humic substances were highest in MW+PW. The MW+PW and MW+Lime treatments exhibited comparable results with chemically fertilized treatment. The MW acidity neutralized with lime showed positive impacts on growth, yield and nutrients uptake; nevertheless, when MW pH neutralized with PW has an additional benefit on increase in soil organic matter and humic substances. Copyright © 2014. Published by Elsevier Ltd.

  4. Dissipation and distribution of chlorpyrifos in selected vegetables through foliage and root uptake.

    Science.gov (United States)

    Ge, Jing; Lu, Mengxiao; Wang, Donglan; Zhang, Zhiyong; Liu, Xianjin; Yu, Xiangyang

    2016-02-01

    Dissipation, distribution and uptake pathways of chlorpyrifos were investigated in pakchoi (Brassica chinensis L.) and lettuce (Lactuca sativa) with foliage treatments under a greenhouse trial and root treatments under a hydroponic experiment. The dissipation trends were similar for chlorpyrifos in pakchoi and lettuce with different treatments. More than 94% of chlorpyrifos was degraded in the samples for both of the vegetables 21 days after the foliage treatments. For the root treatment, the dissipation rate of chlorpyrifos in pakchoi and lettuce at the low concentration was greater than 93%, however, for the high concentrations, the dissipation rates were all under 90%. Both shoots and roots of the vegetables were able to absorb chlorpyrifos from the environment and distribute it inside the plants. Root concentration factor (RCF) values at different concentrations with the hydroponic experiment ranged from 5 to 39 for pakchoi, and from 14 to 35 for lettuce. The translocation factor (TF) representing the capability of the vegetables to translocate contaminants was significantly different for pakchoi and lettuce with foliage and root treatments. The values of TF with foliage treatments ranged from 0.003 to 0.22 for pakchoi, and from 0.032 to 1.63 for lettuce. The values of TF with root treatments ranged from 0.01 to 0.17 for pakchoi, and from 0.003 to 0.23 for lettuce. Significant difference of TF was found between pakchoi and lettuce with foliage treatments, and at high concentrations (10 and 50 mg L(-1)) with root treatments as well. However, there was no significant difference of TF between pakchoi and lettuce at 1 mg L(-1) with root treatment. Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Estimation of metal uptake in plant parts of roadside grown maize at selected growth stages

    OpenAIRE

    Anongo, M'ember C.; Uyovbisere, Edward O.; Ekong, Nsima J.

    2015-01-01

    Health risk assessment of heavy metals in roadside grown foodcrops consumed by humans is a very good technique because such assessment would provide information about any threat regarding heavy metal contamination. Plant and corresponding soil samples were collected for trace metal analysis to ascertain potential health risks. The non-significant differences of lead (Pb) and cadmium (Cd) levels among the selected growth stages shows that the levels of Pb and Cd in the foodcrops were not influ...

  6. Ultrahigh and Selective SO2 Uptake in Inorganic Anion-Pillared Hybrid Porous Materials.

    Science.gov (United States)

    Cui, Xili; Yang, Qiwei; Yang, Lifeng; Krishna, Rajamani; Zhang, Zhiguo; Bao, Zongbi; Wu, Hui; Ren, Qilong; Zhou, Wei; Chen, Banglin; Xing, Huabin

    2017-07-01

    The efficient capture of SO 2 is of great significance in gas-purification processes including flue-gas desulfurization and natural-gas purification, but the design of porous materials with high adsorption capacity and selectivity of SO 2 remains very challenging. Herein, the selective recognition and dense packing of SO 2 clusters through multiple synergistic host-guest and guest-guest interactions by controlling the pore chemistry and size in inorganic anion (SiF 6 2- , SIFSIX) pillared metal-organic frameworks is reported. The binding sites of anions and aromatic rings in SIFSIX materials grasp every atom of SO 2 firmly via S δ+ ···F δ- electrostatic interactions and O δ- ···H δ+ dipole-dipole interactions, while the guest-guest interactions between SO 2 molecules further promote gas trapping within the pore space, which is elucidated by first-principles density functional theory calculations and powder X-ray diffraction experiments. These interactions afford new benchmarks for the highly efficient removal of SO 2 from other gases, even if at a very low SO 2 concentration. Exceptionally high SO 2 capacity of 11.01 mmol g -1 is achieved at atmosphere pressure by SIFSIX-1-Cu, and unprecedented low-pressure SO 2 capacity is obtained in SIFSIX-2-Cu-i (4.16 mmol g -1 SO 2 at 0.01 bar and 2.31 mmol g -1 at 0.002 bar). More importantly, record SO 2 /CO 2 selectivity (86-89) and excellent SO 2 /N 2 selectivity (1285-3145) are also achieved. Experimental breakthrough curves further demonstrate the excellent performance of these hybrid porous materials in removing low-concentration SO 2 . © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Selective correlations in finite quantum systems and the Desargues property

    Science.gov (United States)

    Lei, C.; Vourdas, A.

    2018-06-01

    The Desargues property is well known in the context of projective geometry. An analogous property is presented in the context of both classical and Quantum Physics. In a classical context, the Desargues property implies that two logical circuits with the same input show in their outputs selective correlations. In general their outputs are uncorrelated, but if the output of one has a particular value, then the output of the other has another particular value. In a quantum context, the Desargues property implies that two experiments each of which involves two successive projective measurements have selective correlations. For a particular set of projectors, if in one experiment the second measurement does not change the output of the first measurement, then the same is true in the other experiment.

  8. Structure-property relationship in cytotoxicity and cell uptake of poly(2-oxazoline) amphiphiles

    KAUST Repository

    Luxenhofer, Robert

    2011-07-01

    The family of poly(2-oxazoline)s (POx) is being increasingly investigated in the context of biomedical applications. We tested the relative cytotoxicity of POx and were able to confirm that these polymers are typically not cytotoxic even at high concentrations. Furthermore, we report structure-uptake relationships of a series of amphiphilic POx block copolymers that have different architectures, molar mass and chain termini. The rate of endocytosis can be fine-tuned over a broad range by changing the polymer structure. The cellular uptake increases with the hydrophobic character of the polymers and is observed even at nanomolar concentrations. Considering the structural versatility of this class of polymers, the relative ease of preparation and their stability underlines the potential of POx as a promising platform candidate for the preparation of next-generation polymer therapeutics.

  9. Nodulation and nitrogen uptake characteristics as selection indices for promiscuous soybean breeding in Africa

    International Nuclear Information System (INIS)

    Ababio, R.C.; Sanginga, K.E.; Dashiell, K.E.

    2001-01-01

    Selection for atmospheric dinitrogen fixation in promiscuous soybeans by indigenous rhizobia populations is usually determined indirectly based on visual assessment of nodulation. As the method has been criticized extensively, we have examined this assay in relation to other N 2 fixation indices by evaluating growth of promiscuous soybeans in four ecological zones of Nigeria. Nodulation was affected considerably by rainfall indigenous, rhizobia populations and soil P. The N 2 fixation indices measured, nodule development, apparent effectiveness, total N accumulation and N derived from fixation, varied among soybean genotypes. The visual nodule assessment index correlated with nodule weight (r = 0.74; P = 0.01), but had no significant correlation (r = 0.13) with proportion of apparent effective nodules. All nodule parameters, however, correlated significantly (r = 0.16-0.71; P=0.05) with total N accumulation and seed yield. The percent apparent effectiveness of nodules was a superior index to nodule score and nodule number but inferior to nodule mass. Total N accumulation patterns in the genotypes indicated that N 2 fixation in some genotypes could be substantial during the reproductive growth phase and may serve as suitable criteria for selection. Therefore, in low N soils, percent nodule effectiveness and total N accumulation may be used to augment the visual scores particularly for genotypes, which seem to nodulate profusely with indigenous rhizohia populations (author)

  10. Chronic effects of fluoxetine, a selective inhibitor of serotonin uptake, on neurotransmitter receptors

    International Nuclear Information System (INIS)

    Wong, D.T.; Reid, L.R.; Bymaster, F.P.; Threlkeld, P.G.

    1985-01-01

    Fluoxetine administration to rats dose of 10mg/kg i.p. daily up to 12 or 24 days failed to change the concentration-dependent binding of [ 3 H]WB4101, [ 3 H]clonidine and [ 3 H]dihydroalprenolol to α 1 -, α 2 - and β-adrenergic receptors, respectively; [ 3 H]quinuclidinyl benzilate to muscarinic receptors; [ 3 H]pyrilamine to histamine H 1 receptors and [ 3 H]naloxone to opiate receptors. Persistent and significant decreases in receptor number (Bsub(max) value) without changes in the dissociation constant (Ksub(D) value) of [ 3 H]5-HT binding in cortical membranes were observed upon chronic treatment with fluoxetine administered either by intraperitoneal injection or incorporation in the diet. A detectable reduction of 5-HT 1 receptor number occured after once-daily injections of fluoxetine at 10mg/kg i.p. within 49 hours. After pretreatment for 3 days with p-chlorophenylalanine, an inhibitor of 5-HT synthesis, followed by repeated administration of fluoxetine, 5-HT 1 receptor numbers were higher than those of normal rats, suggesting a dependence on synaptic concentration of 5-HT for fluoxetine to affect a receptor down-regulation. These studies provide further evidence for the selectivity of fluoxetine as an inhibitor of 5-HT reuptake, resulting in a selective down-regulation of 5-HT 1 receptors in the cerebal cortex of rat brain. (Author)

  11. A cellular uptake and cytotoxicity properties study of gallic acid-loaded mesoporous silica nanoparticles on Caco-2 cells

    Science.gov (United States)

    Rashidi, Ladan; Vasheghani-Farahani, Ebrahim; Soleimani, Masoud; Atashi, Amir; Rostami, Khosrow; Gangi, Fariba; Fallahpour, Masoud; Tahouri, Mohammad Taher

    2014-03-01

    In this study, the effects of intracellular delivery of various concentrations of gallic acid (GA) as a semistable antioxidant, gallic acid-loaded mesoporous silica nanoparticles (MSNs-GA), and cellular uptake of nanoparticles into Caco-2 cells were investigated. MSNs were synthesized and loaded with GA, then characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, N2 adsorption isotherms, X-ray diffraction, and thermal gravimetric analysis. The cytotoxicity of MSNs and MSNs-GA at low and high concentrations were studied by means of 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide (MTT) test and flow cytometry. MSNs did not show significant toxicity in various concentrations (0-500 μg/ml) on Caco-2 cells. For MSNs-GA, cell viability was reduced as a function of incubation time and different concentrations of nanoparticles. The in vitro GA release from MSNs-GA exhibited the same antitumor properties as free GA on Caco-2 cells. Flow cytometry results confirmed those obtained using MTT assay. TEM and fluorescent microscopy confirmed the internalization of MSNs by Caco-2 cells through nonspecific cellular uptake. MSNs can easily internalize into Caco-2 cells without deleterious effects on cell viability. The cell viability of Caco-2 cells was affected during MSNs-GA uptake. MSNs could be designed as suitable nanocarriers for antioxidants delivery.

  12. Coke properties in relation to charge preparation techniques. [Selective crushing

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, O S

    1979-01-01

    Selective crushing is essential to obtain the required coke properties, so that in the coarse fractions there is a considerable reduction in the middlings and dirt normally difficult to crush. These are at the same time enriched with vitrinite so that there is an increase in the coal substance as such, reflected in improved caking capacity in the coarse size range. Various methods of selective crushing are employed, including air entrainment mills, fluidised bed systems. Other advantages claimed for selective crushing are the uniform pore distribution and air permeability and also the diminished breakage stress.

  13. (Z)-dimethylamino-1-(4-bromophenyl)-1-(3-pyridyl) propene (H 102/09), a new selective inhibitor of the neuronal 5-hydroxytryptamine uptake

    International Nuclear Information System (INIS)

    Ross, S.B.; Oegren, S.-O.; Renyi, A.L.

    1976-01-01

    The inhibition of the uptake of 3 H-(-)-noradrenaline (NA), 3 H-dopamine and 14 C-5-hydroxytryptamine (5-HT) in mouse brain slices by (Z)-3-dimethylamino-1-(4-bromophenyl)-1-(3-pyridyl)propene(H 102/09), desipramine and chlorimipramine and their releasing effect on the 3 H-amines previously accumulated in the slices were examined. The interactions with reserpine produced hypothermia and sedation and the 5-hydroxytryptophan (5-HTP) syndrome in mice were also studied. Due to the poor inhibitory activity on the NA uptake H 102/09 was a more selective inhii.or of the 5-HT uptake than was chlorimipramine, particularly after administration in vivo, where it was as potent as chlorimipramine (ED50=19μmol/kg intraperitoneally). In vitro chlorimipramine was 6 to 12 times more active than H 102/09. Desipramine was a very selective inhibitor of the NA uptake in vitro and in vivo. The compounds were generally more potent in inhibiting the uptake than in releasing the amines. However, in striatal slices the inhibition of DA uptake could be due to the releasing effect since the difference in potencies were small. The effect of desipramine on 5-HT uptake and that of H102/09 on NA uptake could also involve a release component. The 5-HTP syndrome was potentiated by H 102/09 and chlorimipramine but not by desipramine. The reserpine hypothermia but not the sedation was potently antagonized and reversed by desipramine and by chlorimipramine at high doses but not by H 102/09, suggested that NA but not 5-HT is involved in the hypothermic action of reserpine. (author)

  14. Effect of animal manures on selected soil chemical properties (1 ...

    African Journals Online (AJOL)

    The effects of animal manures on selected soil properties were studied in the laboratory. Manures of Rabbit (RBM), Swine (SWM), Poultry (POM), Goat, (GTM) and Cow (COM) were added at 10, 20, 30 and 40 t/ha to an acidic Ultisol. The amended soils were incubated at 70% water holding capacity for 3 weeks.

  15. Surface Estimation, Variable Selection, and the Nonparametric Oracle Property.

    Science.gov (United States)

    Storlie, Curtis B; Bondell, Howard D; Reich, Brian J; Zhang, Hao Helen

    2011-04-01

    Variable selection for multivariate nonparametric regression is an important, yet challenging, problem due, in part, to the infinite dimensionality of the function space. An ideal selection procedure should be automatic, stable, easy to use, and have desirable asymptotic properties. In particular, we define a selection procedure to be nonparametric oracle (np-oracle) if it consistently selects the correct subset of predictors and at the same time estimates the smooth surface at the optimal nonparametric rate, as the sample size goes to infinity. In this paper, we propose a model selection procedure for nonparametric models, and explore the conditions under which the new method enjoys the aforementioned properties. Developed in the framework of smoothing spline ANOVA, our estimator is obtained via solving a regularization problem with a novel adaptive penalty on the sum of functional component norms. Theoretical properties of the new estimator are established. Additionally, numerous simulated and real examples further demonstrate that the new approach substantially outperforms other existing methods in the finite sample setting.

  16. Inhaled tobacco sterols: uptake by the lungs and disposition to selected organs of rats

    International Nuclear Information System (INIS)

    Holden, W.E.; Maier, J.M.; Liebler, J.M.; Malinow, M.R.

    1988-01-01

    Tobacco sterols (cholesterol, beta-sitosterol, campesterol, and stigmasterol) are present in tobacco smoke and appear in plasma of mammals exposed to cigarette smoke. Because tobacco sterols may be important in the pathogenesis of smoking-induced lung and vascular diseases, we studied the pattern of deposition of cigarette sterols in the lungs and appearance of cigarette sterols in plasma and body organs of rats. After exposure to twenty 5 ml puffs of smoke from tobacco labeled with [4- 14 C]cholesterol or beta-[4- 14 C]sitosterol, rats were killed just after exposure (day 0) and on days 2, 5, 8, 11, 15, and 30, and the lungs and selected body organs analyzed for activity. We found that cigarette sterols are associated with particulates in cigarette smoke, deposited mostly in distal airspaces and parenchyma of the lungs, and appear in plasma and several body organs for more than 30 days after this single exposure to cigarette smoke. Bronchoalveolar lavage fluid contained relatively small amounts of radiolabel for only the first few days, suggesting that most of the sterols were rapidly incorporated in lung parenchyma. Because disorders of sterol metabolism have been implicated in a variety of diseases including atherosclerosis and cancer, the significance of tobacco sterols to human smoking-induced diseases deserves further study

  17. Effect of coal ash on growth and metal uptake by some selected ectomycorrhizal fungi in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Ray, P.; Reddy, U.G.; Lapeyrie, F.; Adholeya, A. [Energy & Resources Institute, New Delhi (India)

    2005-07-01

    Six isolates of ectomycorrhizal fungi namely, Laccaria fraterna (EM-1083), Pisolithus tinctorius (EM-1081), Pisolithus tinctorius (EM-1290), Pisolithus tinctorius (EM-1293), Scleroderma verucosurn (EM-1283), and Scleroderma cepa (EM-1233), were grown on three variants of coal ash, namely electrostatically precipitated (ESP) ash, pond ash, and bottom ash moistened with Modified Melin-Norkans (MMN) medium in vitro. The colony diameter reflected the growth of the isolates on the coal ash. Metal accumulation in the mycelia was assayed by atomic absorption spectrophotometry. Six metals, namely aluminum, cadmium, chromium, iron, lead, and nickel were selected on the basis of their abundance in coal ash and toxicity potential for the present work. Growth of vegetative mycelium on fly ash variants and metal accumulation data indicated that Pisolithus tinctorius (EM-1290) was the most tolerant among the isolates tested for most of the metals. Since this isolate is known to be mycorrhizal with Eucalyptus, it could be used for the reclamation of coal ash over burdened sites.

  18. Selective Mitochondrial Uptake of MKT-077 Can Suppress Medullary Thyroid Carcinoma Cell Survival and

    Directory of Open Access Journals (Sweden)

    Dmytro Starenki

    2015-12-01

    Full Text Available BackgroundMedullary thyroid carcinoma (MTC is a neuroendocrine tumor mainly caused by mutations in the rearranged during transfection (RET proto-oncogene. Not all patients with progressive MTC respond to current therapy inhibiting RET, demanding additional therapeutic strategies. We recently demonstrated that disrupting mitochondrial metabolism using a mitochondria-targeted agent or by depleting a mitochondrial chaperone effectively suppressed human MTC cells in culture and in mouse xenografts by inducing apoptosis and RET downregulation. These observations led us to hypothesize that mitochondria are potential therapeutic targets for MTC. This study further tests this hypothesis using1-ethyl-2-[[3-ethyl-5-(3-methylbenzothiazolin-2-yliden]-4-oxothiazolidin-2-ylidenemethyl] pyridinium chloride (MKT-077, a water-soluble rhodocyanine dye analogue, which can selectively accumulate in mitochondria.MethodsThe effects of MKT-077 on cell proliferation, survival, expression of RET and tumor protein 53 (TP53, and mitochondrial activity were determined in the human MTC lines in culture and in mouse xenografts.ResultsMKT-077 induced cell cycle arrest in TT and MZ-CRC-1. Intriguingly, MKT-077 also induced RET downregulation and strong cell death responses in TT cells, but not in MZ-CRC-1 cells. This discrepancy was mainly due to the difference between the capacities of these cell lines to retain MKT-077 in mitochondria. The cytotoxicity of MKT-077 in TT cells was mainly attributed to oxidative stress while being independent of TP53. MKT-077 also effectively suppressed tumor growth of TT xenografts.ConclusionMKT-077 can suppress cell survival of certain MTC subtypes by accumulating in mitochondria and interfering with mitochondrial activity although it can also suppress cell proliferation via other mechanisms. These results consistently support the hypothesis that mitochondrial targeting has therapeutic potential for MTC.

  19. Effects of soil's properties on transfer of 137Cs to rice plants through plant uptake after soil deposition

    International Nuclear Information System (INIS)

    Keum, Dong-Kwon; Lee, Hansoo; Kang, Hee-Seok; Jun, In; Choi, Yong-Ho; Lee, Chang-Woo

    2007-01-01

    This paper presents a dynamic compartment model to appraise the concentration of 137 Cs in agricultural plants as a result of a soil deposition. The present model used the Absalom model as a module to account for the effects of a soil's properties (pH, soil clay content, organic matter content, and exchangeable potassium) on a plant uptake, and the leaching and fixation process of 137 Cs in a soil. The model was tested by comparing the model predictions of the 137 Cs aggregated transfer factors for rice plants with those obtained as results of simulated 137 Cs soil deposition experiments with seventeen paddy soils of different properties, all of which were performed before a transplanting of the rice. Predicted 137 Cs TF a values of the rice plants were found to be comparable with those observed. (author)

  20. Thermophysical Properties of Selected II-VI Semiconducting Melts

    Science.gov (United States)

    Li, C.; Su, Ching-Hua; Lehoczky, S. L.; Scripa, R. N.; Ban, H.; Lin, B.

    2004-01-01

    Thermophysical properties are essential for the accurate predication of the crystal growth process by computational modeling. Currently, the temperature dependent thermophysical property data for the II-VI semiconductor melts are scarce. This paper reports the results of the temperature dependence of melt density, viscosity and electrical conductivity of selected II-VI compounds, including HgTe, HgCdTe and HgZnTe. The melt density was measured using a pycnometric method, and the viscosity and electrical conductivity were measured by a transient torque method. The results were compared with and showed good agreement with the existing data in the literature.

  1. Far-infrared properties of optically selected quasars

    International Nuclear Information System (INIS)

    Edelson, R.A.

    1986-01-01

    The far-infrared properties of 10, optically selected quasars were studied on the basis of pointed IRAS observations and ground-based near-infrared and radio measurements. Nine of these quasars were detected in at least three IRAS bands. The flat spectral energy distributions characterizing these optically selected quasars together with large 60-100-micron luminosities suggest that the infrared emission is dominated by nonthermal radiation. Seven of the nine quasars with far-infrared detections were found to have low-frequency turnovers. 12 references

  2. 137Cs and 90Sr root uptake by beans in soils with contrasting properties

    International Nuclear Information System (INIS)

    Sauras Yera, T.; Vallejo, R.; Waegeneers, N.; Madoz-Escande, C.

    1998-01-01

    Radionuclide soil to crop transfer was analysed in large undisturbed soil monoliths installed in lysimeters under controlled climatic conditions. Both the solid/liquid distribution coefficient K D (= [RN] in soil (Bq/kg)/[RN] in soil solution (Bq/l)) and the concentration factor CF (= (Bq/kg plant)/(Bq/l soil solution)) are affected by the concentration of K, Ca and Mg in soil solution. The 137 Cs concentration in soil solution varied from 400 Bq/l to 9 Bq/l in the various types of soil, the corresponding K D value ranged from 480 to 19000 l/kg. The concentration of potassium in the soil solution (m K ) varied from 25 mmol/l to 0.6 mmol/l. A negative linear relationship on the logarithmic scale was found between K D and the potassium status of the soil solution: high K levels brought about low K D 's and thus, promotion of 137 Cs in the soil solution. The plant concentration factor was also affected by the K concentration: high K contents in soil solution resulted in low CF's and vice versa. The interdependence was again linear in logarithmic coordinates. The 137 Cs root uptake crop reflected the specific scenario of each soil. The K D and CF values were also negatively related to the Ca+Mg concentration in the soil solution. Thus, K, Ca and Mg in the soil solution play an important role in the 137 Cs and 90 Sr root uptake and, in addition to the soil type and specific growing conditions, are important factors governing the transfer

  3. Synthesis of /sup 14/C- and /sup 3/H-labeled fluoxetine, a selective serotonin uptake inhibitor

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, D.W.; Krushinski, J.H.; Wong, D.T.; Kau, D.

    1987-11-01

    Fluoxetine (N-methyl-..gamma..-(4-(trifluoromethyl)phenoxy) benzenepropanamine) is a potent, highly selective serotonin uptake inhibitor that is useful in treating a variety of major psychiatric derangements. We have synthesized this compound in /sup 14/C- and /sup 3/H-labeled forms. The tritium label was introduced in the final step by catalytic dehalogenation of the brominated fluoxetine precursor. Reaction conditions could be controlled such that catalytic hydrogenolysis of the labile C-O benzylic bond was minimized. Following HPLC purification, (/sup 3/H)-fluoxetine was obtained in a state of high radiochemical purity (98%) and specific activity (20.4 Ci/mmol). The /sup 14/C-label was introduced in the final step via a nucleophilic aromatic substitution reaction between the sodium salt of ..cap alpha..-(2-(methylamino)ethyl)benzenemethanol and uniformly ring-labeled p-chlorobenzotrifluoride. Following purification by flash chromatography, (/sup 14/C)-fluoxetine was obtained in 98.3% radiochemical purity with a specific activity of 5.52 mCi/mmol.

  4. Observational evidence for pollution-influenced selective uptake contributing to biogenic secondary organic aerosols in the southeastern U.S.

    Science.gov (United States)

    Liu, J.; Russell, L. M.; Lee, A. K. Y.; McKinney, K. A.; Surratt, J. D.; Ziemann, P. J.

    2017-08-01

    During the 2013 Southern Oxidant and Aerosol Study, aerosol mass spectrometer measurements of submicron mass and single particles were taken at Look Rock, Tennessee. Their concentrations increased during multiday stagnation events characterized by low wind, little rain, and increased daytime isoprene emissions. Organic mass (OM) sources were apportioned as 42% "vehicle-related" and 54% biogenic secondary organic aerosol (bSOA), with the latter including "sulfate-related bSOA" that correlated to sulfate (r = 0.72) and "nitrate-related bSOA" that correlated to nitrate (r = 0.65). Single-particle mass spectra showed three composition types that corresponded to the mass-based factors with spectra cosine similarity of 0.93 and time series correlations of r > 0.4. The vehicle-related OM with m/z 44 was correlated to black carbon, "sulfate-related bSOA" was on particles with high sulfate, and "nitrate-related bSOA" was on all particles. The similarity of the m/z spectra (cosine similarity = 0.97) and the time series correlation (r = 0.80) of the "sulfate-related bSOA" to the sulfate-containing single-particle type provide evidence for particle composition contributing to selective uptake of isoprene oxidation products onto particles that contain sulfate from power plants.

  5. Non-transferrin-bound iron (NTBI uptake by T lymphocytes: evidence for the selective acquisition of oligomeric ferric citrate species.

    Directory of Open Access Journals (Sweden)

    Joao Arezes

    Full Text Available Iron is an essential nutrient in several biological processes such as oxygen transport, DNA replication and erythropoiesis. Plasma iron normally circulates bound to transferrin. In iron overload disorders, however, iron concentrations exceed transferrin binding capacity and iron appears complexed with low molecular weight molecules, known as non-transferrin-bound iron (NTBI. NTBI is responsible for the toxicity associated with iron-overload pathologies but the mechanisms leading to NTBI uptake are not fully understood. Here we show for the first time that T lymphocytes are able to take up and accumulate NTBI in a manner that resembles that of hepatocytes. Moreover, we show that both hepatocytes and T lymphocytes take up the oligomeric Fe3Cit3 preferentially to other iron-citrate species, suggesting the existence of a selective NTBI carrier. These results provide a tool for the identification of the still elusive ferric-citrate cellular carrier and may also open a new pathway towards the design of more efficient iron chelators for the treatment of iron overload disorders.

  6. Microstructure and mechanical properties of selective laser melted magnesium

    International Nuclear Information System (INIS)

    Ng, C.C.; Savalani, M.M.; Lau, M.L.; Man, H.C.

    2011-01-01

    The effects of laser processing parameters on the microstructure and mechanical properties of selective laser-melted magnesium were investigated. The results show that the microstructure characteristics of the laser-melted samples are dependent on the grain size of SLM magnesium. The grains in the molten zone coarsen as the laser energy density increases. In addition, the average hardness values of the molten zone decreases significantly with an increase of the laser energy densities and then decreased slowly at a relatively high laser energy density irrespective of mode of irradiation. The hardness value was obtained from 0.59 to 0.95 GPa and corresponding elastic modulus ranging from 27 to 33 GPa. The present selective laser-melted magnesium parts are promising for biomedical applications since the mechanical properties are more closely matched with human bone than other metallic biomaterials.

  7. Changes in soil properties and plant uptake of heavy metals on ...

    African Journals Online (AJOL)

    Administrator

    could be attributed to interactions of different soil properties rather a single factor. Key words: Heavy ... side the required essential nutrients. ..... Lead for instance increased .... zinc, cadmium, iron, and manganese in soils near a copper smelter.

  8. Selected properties of new „duplex” cast steel

    Directory of Open Access Journals (Sweden)

    S. Pietrowski

    2011-10-01

    Full Text Available In this paper selected properties of new „duplex” cast steel are presented. The new cast steel was devised in HYDRO-VACUUM company in Grudziądz, where “duplex” cast steel for pump elements is smelted. The goal was to devise a new grade of “duplex” cast steel of better physicochemical properties and cheaper than now applied. It was demonstrated, that there is the possibility of devising the new grade of “duplex” cast steel. It is characterized by higher mechanical properties, similar wear resistance and greater corrosion resistance in 15% water solution of H2SO4 in comparison to now applied “duplex” cast steel. The chemical composition was selected to obtain in microstructure about of 50% ferrite and 50% austenite. It guarantee the highest properties and the lowest costs of its smelting.In the paper results of: the microstructure, Rm, Rp0,2, A5, HB, wear resistance and corrosion resistance in water solution of 15% HCl and H2SO4 acids of new cast steel was presented. They were compared with now applied in HYDRO-VACUUM company “duplex” cast steel.

  9. Properties of Risk Measures of Generalized Entropy in Portfolio Selection

    Directory of Open Access Journals (Sweden)

    Rongxi Zhou

    2017-12-01

    Full Text Available This paper systematically investigates the properties of six kinds of entropy-based risk measures: Information Entropy and Cumulative Residual Entropy in the probability space, Fuzzy Entropy, Credibility Entropy and Sine Entropy in the fuzzy space, and Hybrid Entropy in the hybridized uncertainty of both fuzziness and randomness. We discover that none of the risk measures satisfy all six of the following properties, which various scholars have associated with effective risk measures: Monotonicity, Translation Invariance, Sub-additivity, Positive Homogeneity, Consistency and Convexity. Measures based on Fuzzy Entropy, Credibility Entropy, and Sine Entropy all exhibit the same properties: Sub-additivity, Positive Homogeneity, Consistency, and Convexity. These measures based on Information Entropy and Hybrid Entropy, meanwhile, only exhibit Sub-additivity and Consistency. Cumulative Residual Entropy satisfies just Sub-additivity, Positive Homogeneity, and Convexity. After identifying these properties, we develop seven portfolio models based on different risk measures and made empirical comparisons using samples from both the Shenzhen Stock Exchange of China and the New York Stock Exchange of America. The comparisons show that the Mean Fuzzy Entropy Model performs the best among the seven models with respect to both daily returns and relative cumulative returns. Overall, these results could provide an important reference for both constructing effective risk measures and rationally selecting the appropriate risk measure under different portfolio selection conditions.

  10. The Influence of Water and Solvent Uptake on Functional Properties of Shape-Memory Polymers

    Directory of Open Access Journals (Sweden)

    Ehsan Ghobadi

    2018-01-01

    Full Text Available In this contribution, diffusion of water, acetone, and ethanol into a polymer matrix has been studied experimentally and numerically by finite element approaches. Moreover, the present study reports an assessment of different thermomechanical conditions of the shape-memory (SM performance, for example, stress- or strain-holding times in stress- or strain-controlled thermomechanical cycles and the effect of maximum strain. According to the results presented here, the uptake of acetone in Estane is much higher than ethanol and follows classical Fickian diffusion. Further, a series of thermomechanical measurements conducted on dry and physically (hydrolytically aged polyether urethanes revealed that incorporation of water seems to have an appreciable impact on the shape recovery ratios which can be attributed to the additional physical crosslinks. However, no obvious difference in shape fixation of dry and physically (hydrolytically aged samples could be recognized. Furthermore, by decreasing the strain-holding time, shape recovery improves significantly. Moreover, the shape fixity is found to be independent of holding time. The shape recovery ratio decreased dramatically with an increase in the stress-holding time.

  11. Tailoring the ligand shell for the control of cellular uptake and optical properties of nanocrystals

    Directory of Open Access Journals (Sweden)

    Johannes Ostermann

    2015-01-01

    Full Text Available In this short review, the main challenges in the use of hydrophobic nanoparticles in biomedical application are addressed. It is shown how to overcome the different issues by the use of a polymeric encapsulation system, based on an amphiphilic polyisoprene-block-poly(ethylene glycol diblock copolymer. On the basis of this simple molecule, the development of a versatile and powerful phase transfer strategy is summarized, focusing on the main advantages like the adjustable size, the retained properties, the excellent shielding and the diverse functionalization properties of the encapsulated nanoparticles. Finally, the extraordinary properties of these encapsulated nanoparticles in terms of toxicity and specificity in a broad in vitro test is demonstrated.

  12. Effect of Mineral and Humic Substances on Tailing Soil Properties and Nutrient Uptake by Pennisetum purpureum Schumach

    Directory of Open Access Journals (Sweden)

    Adhe Phoppy Wira Etika

    2015-05-01

    Full Text Available Tin mining produces a by-product sand tailing from soil leaching with characteristic low pH and total organic carbon, and can be reclaimed by providing a suitable ameliorant. When available in situ, ameliorant materials can be economically used as they are required in large amounts. Fortunately, Bangka Belitung has sample stock of such kaolinite-rich minerals that can be utilized for improving soil chemical properties. Extracted organic materials, such as humic substances, can also be utilized as they influence the complex soil reactions, and promote plant growth. Thus, this study aimed to assess the effects of mineral, humic materials and interaction of both material on soil chemical properties and nutrient uptake of Pennisetum purpureum Schumach. A completely randomized design with 2 factors and 3 replications each was employed. Factor 1 was mineral matter is 0; 420; 840; 1.260 Mg ha-1 while Factor 2 was humic material is 0; 0.46; 0.92; 1.38 kg C ha-1. Air-dried samples of tailing were applied with oil palm compost then mixed evenly with mineral and humic materials. Penissetum purpureum Schumach was planted after 4 weeks incubation, and maintained for another 4 weeks. The results demonstrated that the addition of mineral matter significantly increased soil organic carbon content, total N, exchangeable K, Fe, Mn and boosted nutrient - total Ca, Mg and Mn – uptake of the plant. But the application of humic material increased only soil organic carbon content. The interaction of both materials only lowered soil pH.

  13. Properties of Soils and Plants Uptake within the Vicinity of Selected ...

    African Journals Online (AJOL)

    `123456789jkl''''#

    nutrients. So, as the soil is being contaminated with all manner of pollutants, the life process is being ... food chain (Ademoroti, 1996). Animals ... range of 260-300 m above the sea level in Ife ... thoroughly washed with de-ionized water dried.

  14. TEHDGA; DMDOHEMA and mixed sorbents: characterization and Am(III) uptake properties

    Energy Technology Data Exchange (ETDEWEB)

    Petit, S.; Bertolo, L.; Petitjean, F.; Marie, C.; Conocar, O.; Thiebaut, V. [CEA, Nuclear Energy Division, Radiochemistry and Process Department, Marcoule Center, F-30207 Bagnols-sur-Ceze (France)

    2016-07-01

    The Atalante research facility produces radioactive waste that have to be managed according to specific rules. In particular, solid and liquid wastes need to be transferred to another facility in Marcoule to be evaporated with an alpha activity limit of 16.65 GBq/m{sup 3}. The radioactive aqueous nitric acid wastes produced in Atalante must be first decontaminated by removing U, Pu and minor actinides and therefore a dedicated decontamination program for radioactive aqueous nitric acid wastes is implemented in Atalante. In particular, the recovery of americium and curium is obtained by extraction chromatography. TEHDGA (N, N, N', N'-tetra-2-ethylhexyl-3-oxopentane-1,5-diamide), DMDOHEMA ((N,N'-dimethyl-N,N'-dioctyl-hexyl-oxyethyl malonamide) and a mixture of both extractants were impregnated on silica gel and studied. Batch experiments were made to determine the performances of such a process. The weight distribution coefficients (Dw) were determined for Am and Nd. Different kinetic behavior was found with both complexing agents. An effect of nitric acid concentration was observed. For 3 solids, the americium's uptake increases with acidity. Loading capacities by isotherm and Langmuir isotherm are obtained (between 48 mg/g and 94 mg/g). After determining various parameters in batch extraction experiments, the performances of the solid supports were studied in columns. The breakthrough and elution curves were obtained with neodymium (respectively between 12 mg/g and 21 mg/g; 0.17 and 0.27 L/g). Capacity and recovery were optimized with the mixture of DMDOHEMA and TEHDGA. (authors)

  15. Tritium Suicide Selection Identifies Proteins Involved in the Uptake and Intracellular Transport of Sterols in Saccharomyces cerevisiae▿

    Science.gov (United States)

    Sullivan, David P.; Georgiev, Alexander; Menon, Anant K.

    2009-01-01

    Sterol transport between the plasma membrane (PM) and the endoplasmic reticulum (ER) occurs by a nonvesicular mechanism that is poorly understood. To identify proteins required for this process, we isolated Saccharomyces cerevisiae mutants with defects in sterol transport. We used Upc2-1 cells that have the ability to take up sterols under aerobic conditions and exploited the observation that intracellular accumulation of exogenously supplied [3H]cholesterol in the form of [3H]cholesteryl ester requires an intact PM-ER sterol transport pathway. Upc2-1 cells were mutagenized using a transposon library, incubated with [3H]cholesterol, and subjected to tritium suicide selection to isolate mutants with a decreased ability to accumulate [3H]cholesterol. Many of the mutants had defects in the expression and trafficking of Aus1 and Pdr11, PM-localized ABC transporters that are required for sterol uptake. Through characterization of one of the mutants, a new role was uncovered for the transcription factor Mot3 in controlling expression of Aus1 and Pdr11. A number of mutants had transposon insertions in the uncharacterized Ydr051c gene, which we now refer to as DET1 (decreased ergosterol transport). These mutants expressed Aus1 and Pdr11 normally but were severely defective in the ability to accumulate exogenously supplied cholesterol. The transport of newly synthesized sterols from the ER to the PM was also defective in det1Δ cells. These data indicate that the cytoplasmic protein encoded by DET1 is involved in intracellular sterol transport. PMID:19060182

  16. Characteristics of wood ash and influence on soil properties and nutrient uptake: an overview.

    Science.gov (United States)

    Demeyer, A; Voundi Nkana, J C; Verloo, M G

    2001-05-01

    Wood industries and power plants generate enormous quantities of wood ash. Disposal in landfills has been for long a common method for removal. New regulations for conserving the environment have raised the costs of landfill disposal and added to the difficulties for acquiring new sites for disposal. Over a few decades a number of studies have been carried out on the utilization of wood ashes in agriculture and forestry as an alternative method for disposal. Because of their properties and their influence on soil chemistry the utilization of wood ashes is particularly suited for the fertility management of tropical acid soils and forest soils. This review principally focuses on ash from the wood industry and power plants and considers its physical, chemical and mineralogical characteristics, its effect on soil properties, on the availability of nutrient elements and on the growth and chemical composition of crops and trees, as well as its impact on the environment.

  17. Properties shaping and repair of selected types of cast iron

    Directory of Open Access Journals (Sweden)

    J. Szajnar

    2007-04-01

    Full Text Available The paper presents research results of twofold use of TIG - Tungsten Inert Gas also known as GTA - Gas Tungsten Arc. First is surfacing by welding on cold and hot-cold to repair chromium cast iron with chromium content about 15%. Second is remelting with electric arc of selected gray (with pearlitic matrix and ductile (with ferritic-pearlitic matrix cast iron. Repair of cast iron elements was realized in order to cut out a casting defects. Defects decrease a usability of castings for constructional application and increase a manufacturing costs. Application of surface heat treatment guarantees mechanical properties i.e. hardness and wear resistance improvement. The result of investigations show possibility of castings repair by put on defects a good quality padding welds, which have comparable properties with base material. Use of electric arc surface heat treatment resulted in increase of hardness and wear resistance, which was measured on the basis of ASTM G 65 - 00 standard.

  18. Properties of selected superconductive materials, 1978 supplement. Technical note

    International Nuclear Information System (INIS)

    Roberts, B.W.

    1978-10-01

    This report includes data on additional superconductive materials extracted from the world literature up to fall 1977 and is an addendum to the data set published in J. Phys. Chem. Ref. Data 5, no. 3, 581-821 (1976) (Reprint no. 84). The data presented are new values and have not been selected or compared to values (except for selected values of the elements) previously assembled by the Superconductive Materials Data Center. The properties included are composition, critical temperature, critical magnetic field, crystal structure and the results of negative experiments. Special tabulations of high magnetic field materials with Type II behavior and materials with organic components are included. All entries are keyed to the literature. A list of recent reviews centered on superconductive materials is included

  19. Multichannel Selective Femtosecond Coherent Control Based on Symmetry Properties

    International Nuclear Information System (INIS)

    Amitay, Zohar; Gandman, Andrey; Chuntonov, Lev; Rybak, Leonid

    2008-01-01

    We present and implement a new scheme for extended multichannel selective femtosecond coherent control based on symmetry properties of the excitation channels. Here, an atomic nonresonant two-photon absorption channel is coherently incorporated in a resonance-mediated (2+1) three-photon absorption channel. By proper pulse shaping, utilizing the invariance of the two-photon absorption to specific phase transformations of the pulse, the three-photon absorption is tuned independently over an order-of-magnitude yield range for any possible two-photon absorption yield. Noticeable is a set of ''two-photon dark pulses'' inducing widely tunable three-photon absorption

  20. FAR-INFRARED PROPERTIES OF SPITZER-SELECTED LUMINOUS STARBURSTS

    International Nuclear Information System (INIS)

    Kovacs, A.; Omont, A.; Fiolet, N.; Beelen, A.; Dole, H.; Lagache, G.; Lonsdale, C.; Polletta, M.; Greve, T. R.; Borys, C.; Dowell, C. D.; Bell, T. A.; Cox, P.; De Breuck, C.; Farrah, D.; Menten, K. M.; Owen, F.

    2010-01-01

    We present SHARC-2 350 μm data on 20 luminous z ∼ 2 starbursts with S 1.2 m m > 2 mJy from the Spitzer-selected samples of Lonsdale et al. and Fiolet et al. All the sources were detected, with S 350 μ m > 25 mJy for 18 of them. With the data, we determine precise dust temperatures and luminosities for these galaxies using both single-temperature fits and models with power-law mass-temperature distributions. We derive appropriate formulae to use when optical depths are non-negligible. Our models provide an excellent fit to the 6 μm-2 mm measurements of local starbursts. We find characteristic single-component temperatures T 1 ≅ 35.5 ± 2.2 K and integrated infrared (IR) luminosities around 10 12.9±0.1 L sun for the SWIRE-selected sources. Molecular gas masses are estimated at ≅4 x 10 10 M sun , assuming κ 850 μ m = 0.15 m 2 kg -1 and a submillimeter-selected galaxy (SMG)-like gas-to-dust mass ratio. The best-fit models imply ∼>2 kpc emission scales. We also note a tight correlation between rest-frame 1.4 GHz radio and IR luminosities confirming star formation as the predominant power source. The far-IR properties of our sample are indistinguishable from the purely submillimeter-selected populations from current surveys. We therefore conclude that our original selection criteria, based on mid-IR colors and 24 μm flux densities, provides an effective means for the study of SMGs at z ∼ 1.5-2.5.

  1. Fluoroethoxy-1,4-diphenethylpiperidine and piperazine derivatives: Potent and selective inhibitors of [3H]dopamine uptake at the vesicular monoamine transporter-2.

    Science.gov (United States)

    Hankosky, Emily R; Joolakanti, Shyam R; Nickell, Justin R; Janganati, Venumadhav; Dwoskin, Linda P; Crooks, Peter A

    2017-12-15

    A small library of fluoroethoxy-1,4-diphenethyl piperidine and fluoroethoxy-1,4-diphenethyl piperazine derivatives were designed, synthesized and evaluated for their ability to inhibit [ 3 H]dopamine (DA) uptake at the vesicular monoamine transporter-2 (VMAT2) and dopamine transporter (DAT), [ 3 H]serotonin (5-HT) uptake at the serotonin transporter (SERT), and [ 3 H]dofetilide binding at the human-ether-a-go-go-related gene (hERG) channel. The majority of the compounds exhibited potent inhibition of [ 3 H]DA uptake at VMAT2, Ki changes in the nanomolar range (K i  = 0.014-0.073 µM). Compound 15d exhibited the highest affinity (K i  = 0.014 µM) at VMAT2, and had 160-, 5-, and 60-fold greater selectivity for VMAT2 vs. DAT, SERT and hERG, respectively. Compound 15b exhibited the greatest selectivity (>60-fold) for VMAT2 relative to all the other targets evaluated, and 15b had high affinity for VMAT2 (K i  = 0.073 µM). Compound 15b was considered the lead compound from this analog series due to its high affinity and selectivity for VMAT2. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Photostability and moisture uptake properties of wood veneers coated with a combination of thin sol-gel films and light stabilizers

    Science.gov (United States)

    Mandla A. Tshabalala; Ryan Libert; Christian M. Schaller

    2011-01-01

    In recent years, there has been increased interest in the use of inorganic UV blocking nanoparticles for photostabilization of wood surfaces. Photostability and moisture uptake properties of wood veneers coated with a combination of hybrid inorganic-organic thin sol-gel films and organic light stabilizers was investigated. The light stabilizers were applied by brushing...

  3. Relationships between properties of Hanford area soils and the availability of 134Cs and 85Sr for uptake by cheatgrass and tumbleweed

    International Nuclear Information System (INIS)

    Cataldo, D.A.; Routson, R.C.; Paine, D.; G.

    1978-10-01

    The relationships between plant root absorption mechanisms and basic soil parameters which effect the concentration of Sr and Cs, and analog ions in soil solution are reviewed. Based on these relationships, studies were undertaken to determine the relative availability of Cs and Sr for uptake by plants grown on Hanford area soils, and the feasibility of developing a predictive relationship between readily measurable soil parameters and plant availability of Cs and Sr. Concentration ratios were determined for cheatgrass and tumbleweed grown on Hanford area soils representing a range in properties (Burbank, Ritzville, Lickskillet, Rupert and Warden). Concentration ratios ranged from 0.0078 to 0.066 and 3.5 to 16 for 134 Cs and 85 Sr, respectively. Soils were analyzed for physical properties, mineralogy, extractable cations and extractable 134 Cs and 85 Sr. Simple correlation analyses showed Cs and Sr uptake in cheatgrass and Sr uptake by tumbleweed to be related to cation exchange capacity, and extractable Sr, Ba and Mg. However, in the case of Cs, this correlation may be coincidental since these divalent cations are not chemical analogs of Cs. Uptake of Cs by tumbleweed showed weak correlations with extractable and exchangeable K. Factor analysis and principle components analysis did not assist in further quantitation of the relationships between plant uptake and soil parameters

  4. Spectral optical properties of selected photosynthetic microalgae producing biofuels

    International Nuclear Information System (INIS)

    Lee, Euntaek; Heng, Ri-Liang; Pilon, Laurent

    2013-01-01

    This paper presents the spectral complex index of refraction of biofuel producing photosynthetic microalgae between 400 and 750 nm. They were retrieved from their experimentally measured average absorption and scattering cross-sections. The microalgae were treated as homogeneous polydisperse spheres with equivalent diameter such that their surface area was identical to that of their actual spheroidal shape. An inverse method was developed combining Lorentz–Mie theory as the forward method and genetic algorithm. The unicellular green algae Chlamydomonas reinhardtii strain CC125 and its truncated chlorophyll antenna transformants tla1, tlaX, and tla1-CW + as well as Botryococcus braunii, Chlorella sp., and Chlorococcum littorale were investigated. These species were selected for their ability to produce either hydrogen gas or lipids for liquid fuel production. Their retrieved real and imaginary parts of the complex index of refraction were continuous functions of wavelength with absorption peaks corresponding to those of in vivo Chlorophylls a and b. The T-matrix method was also found to accurately predict the experimental measurements by treating the microalgae as axisymmetric spheroids with the experimentally measured major and minor diameter distributions and the retrieved spectral complex index of refraction. Finally, pigment mass fractions were also estimated from the retrieved absorption index. The method and/or the reported optical properties can be used in various applications from ocean remote sensing, carbon cycle study, as well as photobiological carbon dioxide mitigation and biofuel production. -- Highlights: ► Retrieval of optical properties from average absorption and scattering cross-sections. ► Inverse method based on Lorentz–Mie theory and genetic algorithm. ► Refraction and absorption indices of selected microalgae between 400 and 750 nm. ► Determination of pigment concentrations from absorption index. ► Good agreement between T

  5. Evaluation of nutraceutical properties of selected small millets.

    Science.gov (United States)

    Rao, B Raghavendra; Nagasampige, Manojkumar H; Ravikiran, M

    2011-04-01

    The aim of this study was to evaluate the nutraceutical properties and nutritional value of grains of four selected small millets viz. finger millet, foxtail millet, prosomillet and khodomillet. The qualitative analysis of phytochemicals viz. phenolics, flavonoids, alkaloids and saponins present in the four small millets was done. The water-soluble proteins, crude fiber content and the reducing power of the grains of these four millets were analyzed. The khodomillet showed maximum phenolic content (10.3%) and foxtail millet showed minimum phenolics (2.5%). As far as reducing capacity was concerned, finger millet was highest (5.7%). The prosomillet showed least reducing property (2.6%). The finger millet (391.3 mg/g each) showed maximum reducing sugar content. The prosomillet showed minimum reducing sugar (195 mg/g). The foxtail millet showed maximum protein content (305.76 mg/g) and prosomillet showed minimum protein content (144.23 mg/g). The khodomillet showed maximum crude fiber content (14.3%).The finger millet showed maximum reducing sugar content (391.3 mg/g) whereas, the khodomillet showed minimum reducing sugar (130.43 mg/g).

  6. Electronic structure and physicochemical properties of selected penicillins

    Science.gov (United States)

    Soriano-Correa, Catalina; Ruiz, Juan F. Sánchez; Raya, A.; Esquivel, Rodolfo O.

    Traditionally, penicillins have been used as antibacterial agents due to their characteristics and widespread applications with few collateral effects, which have motivated several theoretical and experimental studies. Despite the latter, their mechanism of biological action has not been completely elucidated. We present a theoretical study at the Hartree-Fock and density functional theory (DFT) levels of theory of a selected group of penicillins such as the penicillin-G, amoxicillin, ampicillin, dicloxacillin, and carbenicillin molecules, to systematically determine the electron structure of full ?-lactam antibiotics. Our results allow us to analyze the electronic properties of the pharmacophore group, the aminoacyl side-chain, and the influence of the substituents (R and X) attached to the aminoacyl side-chain at 6? (in contrast with previous studies focused at the 3? substituents), and to corroborate the results of previous studies performed at the semiempirical level, solely on the ?-lactam ring of penicillins. Besides, several density descriptors are determined with the purpose of analyzing their link to the antibacterial activity of these penicillin compounds. Our results for the atomic charges (fitted to the electrostatic potential), the bond orders, and several global reactivity descriptors, such as the dipole moments, ionization potential, hardness, and the electrophilicity index, led us to characterize: the active sites, the effect of the electron-attracting substituent properties and their physicochemical features, which altogether, might be important to understand the biological activity of these type of molecules.

  7. Evaluation of nutraceutical properties of selected small millets

    Directory of Open Access Journals (Sweden)

    B Raghavendra Rao

    2011-01-01

    Full Text Available Objective: The aim of this study was to evaluate the nutraceutical properties and nutritional value of grains of four selected small millets viz. finger millet, foxtail millet, prosomillet and khodomillet. Materials and Methods: The qualitative analysis of phytochemicals viz. phenolics, flavonoids, alkaloids and saponins present in the four small millets was done. The water-soluble proteins, crude fiber content and the reducing power of the grains of these four millets were analyzed. Results and Conclusions: The khodomillet showed maximum phenolic content (10.3% and foxtail millet showed minimum phenolics (2.5%. As far as reducing capacity was concerned, finger millet was highest (5.7%. The prosomillet showed least reducing property (2.6%. The finger millet (391.3 mg/g each showed maximum reducing sugar content. The prosomillet showed minimum reducing sugar (195 mg/g. The foxtail millet showed maximum protein content (305.76 mg/g and prosomillet showed minimum protein content (144.23 mg/g. The khodomillet showed maximum crude fiber content (14.3%.The finger millet showed maximum reducing sugar content (391.3 mg/g whereas, the khodomillet showed minimum reducing sugar (130.43 mg/g.

  8. Evaluation of Lactobacillus strains for selected probiotic properties.

    Science.gov (United States)

    Turková, Kristýna; Mavrič, Anja; Narat, Mojca; Rittich, Bohuslav; Spanová, Alena; Rogelj, Irena; Matijašić, Bojana Bogovič

    2013-07-01

    Eleven strains of Lactobacillus collected in the Culture Collection of Dairy Microorganisms (CCDM) were evaluated for selected probiotic properties such as survival in gastrointestinal fluids, antimicrobial activity, and competition with non-toxigenic Escherichia coli O157:H7 for adhesion on Caco-2 cells. The viable count of lactobacilli was reduced during 3-h incubation in gastric fluid followed by 3-h incubation in intestinal fluid. All strains showed antimicrobial activity and the three most effective strains inhibited the growth of at least 16 indicator strains. Antimicrobial metabolites of seven strains active against Lactobacillus and Clostridium indicator strains were found to be sensitive to proteinase K and trypsin, which indicates their proteinaceous nature. The degree of competitive inhibition of non-toxigenic E. coli O157:H7 adhesion on the surface of Caco-2 cells was strain-dependent. A significant decrease (P strains were selected for additional studies of antimicrobial activity, i.e., Lactobacillus gasseri CCDM 215, Lactobacillus acidophilus CCDM 149, and Lactobacillus helveticus CCDM 82.

  9. Selected engineering properties and applications of EPS geofoam

    Science.gov (United States)

    Elragi, Ahmed Fouad

    Expanded polystyrene (EPS) geofoam is a lightweight material that has been used in engineering applications since at least the 1950s. Its density is about a hundredth of that of soil. It has good thermal insulation properties with stiffness and compression strength comparable to medium clay. It is utilized in reducing settlement below embankments, sound and vibration damping, reducing lateral pressure on substructures, reducing stresses on rigid buried conduits and related applications. This study starts with an overview on EPS geofoam. EPS manufacturing processes are described followed by a review of engineering properties found in previous research work done so far. Standards and design manuals applicable to EPS are presented. Selected EPS geofoam-engineering applications are discussed with examples. State-of-the-art of experimental work is done on different sizes of EPS specimens under different loading rates for better understanding of the behavior of the material. The effects of creep, sample size, strain rate and cyclic loading on the stress strain response are studied. Equations for the initial modulus and the strength of the material under compression for different strain rates are presented. The initial modulus and Poisson's ratio are discussed in detail. Sample size effect on creep behavior is examined. Three EPS projects are shown in this study. The creep behavior of the largest EPS geofoam embankment fill is shown. Results from laboratory tests, mathematical modeling and field records are compared to each other. Field records of a geofoam-stabilized slope are compared to finite difference analysis results. Lateral stress reduction on an EPS backfill retaining structure is analyzed. The study ends with a discussion on two promising properties of EPS geofoam. These are the damping ability and the compressibility of this material. Finite element analysis, finite difference analysis and lab results are included in this discussion. The discussion with the

  10. Selective uptake measurements of thyroid nodules with 132I before and after pituitary suppression with T4 and T3, comparison with the TRH assay

    International Nuclear Information System (INIS)

    Eitenmueller, K.

    1977-01-01

    75 patients with suspected hormone-producing autonomous adenoma were examined by the extended TRH assay (BTSH determination, TSH rise 30 min. p.i., and T3 rise 120 min. p.i. 400 μg TRH i.v.) and selective uptake measurements of three different areas of the thyroid using 132 I. The TRH stimulation test alone or the 132 I uptake test alone before and after suppression do not give a clear diagnosis. A clear differentiation of thyroid diseases is only possible if both tests are applied and their results combined. For a differential diagnosis of nodular hyperthyroidism resp. autonomous adenoma, also the TSH stimulation test is necessary in addition to the combination of TRH test and suppression test. (orig./AJ) [de

  11. Selective laser melting of Invar 36: Microstructure and properties

    International Nuclear Information System (INIS)

    Qiu, Chunlei; Adkins, Nicholas J.E.; Attallah, Moataz M.

    2016-01-01

    Invar 36 samples have been fabricated by selective laser melting at a constant laser power but with varied laser scanning speeds. Some samples were further heat treated or hot isostatically pressed (HIPed). The obtained microstructures were studied using optical and electron microscopes, X-ray diffraction and electron backscatter diffraction techniques and the properties evaluated through both tensile testing and thermal expansion measurement. It was found that the as-fabricated samples show very low porosity (<0.5%) when the laser scanning speeds are below 3200 mm/s but show remarkably increased porosity above 3200 mm/s (at 400 W). Increased scanning speed also led to increasingly irregular-shaped laser scanned tracks together with an increased number of pores on sample surfaces and keyhole features within the samples, all indicative of increasingly unstable melt flow behaviour. The as-fabricated microstructure was dominated by columnar γ grains decorated by nanosized α precipitates, resulting in development of texture. Heat treatment did not change microstructure significantly while HIPing closed the majority of pores but also caused pronounced coarsening of α precipitates especially those located at grain boundaries during subsequent slow cooling. With the presence of elongated pores, the vertically built samples were found to show much lower elongation than horizontally built samples while in the absence of pores their ductility has been significantly improved but their tensile strengths are still lower than the latter. The vertically built samples generally failed in a transgranular mode while the horizontally built samples failed in an intergranular mode. HIPing greatly degraded tensile properties due to the presence of coarse grain boundary α precipitates weakening the bonding between grains. Irrespective of building orientations, the as-fabricated samples show low coefficients of thermal expansion below 300 °C comparable to conventionally

  12. Correlation of particle properties with cytotoxicity and cellular uptake of hydroxyapatite nanoparticles in human gastric cancer cells

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Xinhui [State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China); Liang, Tong [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Liu, Changsheng [State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China); Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Yuan, Yuan, E-mail: yyuan@ecust.edu.cn [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China); Qian, Jiangchao, E-mail: jiangchaoqian@ecust.edu.cn [State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China)

    2016-10-01

    Three types of hydroxyapatite nanoparticles (HAPNs) were synthesized employing a sonochemistry-assisted microwave method by changing microwave power (from 200 to 300 W) or using calcination treatment: L200 (200 W, lyophilization), L300 (300 W, lyophilization) and C200 (200 W, lyophilization & calcination). Their physiochemical properties were characterized and correlated with cytotoxicity to human gastric cancer cells (MGC80-3). The major differences among these HAPN preparations were their size and specific surface area, with the L200 showing a smaller size and higher specific surface area. Although all HAPNs inhibited cell proliferation and induced apoptosis of cancer cells, L200 exhibited the greatest toxicity. All types of HAPNs were internalized through energy-dependent pathways, but the L200 nanoparticles were more efficiently uptaken by MGC80-3 cells. Inhibitor studies with dynasore and methyl-β-cyclodextrin suggested that caveolae-mediated endocytosis and, to a much lesser extent, clathrin-mediated endocytosis, were involved in cellular uptake of the various preparations, whereas the inhibition of endocytosis was more obvious for L200. Using fluorescein isothiocyanate-labeled HAPNs and laser-scanning confocal microscopy, we found that all forms of nanoparticles were present in the cytoplasm, and some L200 HAPNs were even found within nuclei. Treatment with all HAPN preparations led to the increase in the intracellular calcium level with the highest level detected for L200. - Highlights: • Three types of HAPNs (L200, L300 and C200) were synthesized employing a sonochemistry-assisted microwave method. • L200 exhibited the greatest cytotoxicity to human gastric cancer (MGC80-3) cells. • L200 showed a smaller size and higher specific surface area. • The L200 nanoparticles were more efficiently uptaken by MGC80-3 cells through energy-dependent pathways. • L200 caused the most significant increase in the intracellular calcium level.

  13. Amendment of Tephrosia Improved Fallows with Inorganic Fertilizers Improves Soil Chemical Properties, N Uptake, and Maize Yield in Malawi

    Directory of Open Access Journals (Sweden)

    Maggie G. Munthali

    2014-01-01

    Full Text Available Maize production in Malawi is limited mainly by low soil N and P. Improved fallows of N-fixing legumes such as Tephrosia and Sesbania offer options for improving soil fertility particularly N supply. The interactions of Tephrosia fallows and inorganic fertilizers on soil properties, N uptake, and maize yields were evaluated at Chitedze Research Station in Malawi. The results indicated that the level of organic matter and pH increased in all the treatments except for the control. Total N remained almost unchanged while available P decreased in all plots amended with T. vogelii but increased in T. candida plots where inorganic P was applied. Exchangeable K increased in all the plots irrespective of the type of amendment. The interaction of N and P fertilizers with T. vogelii fallows significantly increased the grain yield. The treatment that received 45 kg N ha−1 and 20 kg P ha−1 produced significantly higher grain yields (6.8 t ha−1 than all the other treatments except where 68 kg N ha−1 and 30 kg P ha−1 were applied which gave 6.5 t ha−1 of maize grain. T. candida fallows alone or in combination with N and P fertilizers did not significantly affect grain yield. However, T. candida fallows alone can raise maize grain yield by 300% over the no-input control. Based on these results we conclude that high quality residues such as T. candida and T. vogelii can be used as sources of nutrients to improve crop yields and soil fertility in N-limited soils. However, inorganic P fertilizer is needed due to the low soil available P levels.

  14. Modeling Uptake of Selected Pharmaceuticals and Personal Care Products into Food Crops from Biosolids-Amended Soil

    DEFF Research Database (Denmark)

    Prosser, Ryan S.; Trapp, Stefan; Sibley, Paul K.

    2014-01-01

    and comparing them to an acceptable daily intake value. The equilibrium partitioning (EqP) portion of BASL4 overpredicted the concentrations of triclosan, triclocarban, and miconazole in root and shoot tissue by two to three orders of magnitude, while the dynamic carrot root (DCR) portion overpredicted...... by a single order of magnitude. DPU predicted concentrations of triclosan, triclocarban, miconazole, carbamazepine, and diphenhydramine in plant tissues that were within an order of magnitude of concentrations reported in the literature. The study also found that more empirical data are needed on the uptake...

  15. Characterization of the denitrification-associated phosphorus uptake properties of "Candidatus Accumulibacter phosphatis" clades in sludge subjected to enhanced biological phosphorus removal.

    Science.gov (United States)

    Kim, Jeong Myeong; Lee, Hyo Jung; Lee, Dae Sung; Jeon, Che Ok

    2013-03-01

    To characterize the denitrifying phosphorus (P) uptake properties of "Candidatus Accumulibacter phosphatis," a sequencing batch reactor (SBR) was operated with acetate. The SBR operation was gradually acclimated from anaerobic-oxic (AO) to anaerobic-anoxic-oxic (A2O) conditions by stepwise increases of nitrate concentration and the anoxic time. The communities of "Ca. Accumulibacter" and associated bacteria at the initial (AO) and final (A2O) stages were compared using 16S rRNA and polyphosphate kinase genes and using fluorescence in situ hybridization (FISH). The acclimation process led to a clear shift in the relative abundances of recognized "Ca. Accumulibacter" subpopulations from clades IIA > IA > IIF to clades IIC > IA > IIF, as well as to increases in the abundance of other associated bacteria (Dechloromonas [from 1.2% to 19.2%] and "Candidatus Competibacter phosphatis" [from 16.4% to 20.0%]), while the overall "Ca. Accumulibacter" abundance decreased (from 55.1% to 29.2%). A series of batch experiments combined with FISH/microautoradiography (MAR) analyses was performed to characterize the denitrifying P uptake properties of the "Ca. Accumulibacter" clades. In FISH/MAR experiments using slightly diluted sludge (∼0.5 g/liter), all "Ca. Accumulibacter" clades successfully took up phosphorus in the presence of nitrate. However, the "Ca. Accumulibacter" clades showed no P uptake in the presence of nitrate when the sludge was highly diluted (∼0.005 g/liter); under these conditions, reduction of nitrate to nitrite did not occur, whereas P uptake by "Ca. Accumulibacter" clades occurred when nitrite was added. These results suggest that the "Ca. Accumulibacter" cells lack nitrate reduction capabilities and that P uptake by "Ca. Accumulibacter" is dependent upon nitrite generated by associated nitrate-reducing bacteria such as Dechloromonas and "Ca. Competibacter."

  16. Luminescent cyclometalated iridium(III) polypyridine indole complexes--synthesis, photophysics, electrochemistry, protein-binding properties, cytotoxicity, and cellular uptake.

    Science.gov (United States)

    Lau, Jason Shing-Yip; Lee, Pui-Kei; Tsang, Keith Hing-Kit; Ng, Cyrus Ho-Cheong; Lam, Yun-Wah; Cheng, Shuk-Han; Lo, Kenneth Kam-Wing

    2009-01-19

    A series of luminescent cyclometalated iridium(III) polypyridine indole complexes, [Ir(N--C)(2)(N--N)](PF(6)) (HN--C = 2-phenylpyridine (Hppy), N--N = 4-((2-(indol-3-yl)ethyl)aminocarbonyl)-4'-methyl-2,2'-bipyridine (bpy-ind) (1a), N--N = 4-((5-((2-(indol-3-yl)ethyl)aminocarbonyl)pentyl)aminocarbonyl)-4'-methyl-2,2'-bipyridine (bpy-C6-ind) (1b); HN--C = 7,8-benzoquinoline (Hbzq), N--N = bpy-ind (2a), N--N = bpy-C6-ind (2b); and HN--C = 2-phenylquinoline (Hpq), N--N = bpy-ind (3a), N--N = bpy-C6-ind (3b)), have been synthesized, characterized, and their photophysical and electrochemical properties and lipophilicity investigated. Photoexcitation of the complexes in fluid solutions at 298 K and in alcohol glass at 77 K resulted in intense and long-lived luminescence (lambda(em) = 540-616 nm, tau(o) = 0.13-5.15 mus). The emission of the complexes has been assigned to a triplet metal-to-ligand charge-transfer ((3)MLCT) (dpi(Ir) --> pi*(N--N)) excited state, probably with some mixing of triplet intraligand ((3)IL) (pi --> pi*) (pq) character for complexes 3a,b. Electrochemical measurements revealed that all the complexes showed an irreversible indole oxidation wave at ca. +1.1 V versus SCE, a quasi-reversible iridium(IV/III) couple at ca. +1.3 V, and a reversible diimine reduction couple at ca. -1.3 V. The interactions of these complexes with an indole-binding protein, bovine serum albumin (BSA), have been studied by emission titrations, and the K(a) values are on the order of 10(4) M(-1). Additionally, the cytotoxicity of the complexes toward human cervix epithelioid carcinoma (HeLa) cells has been examined by the 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyltetrazolium bromide (MTT) assay. The IC(50) values of the complexes ranged from 1.1 to 6.3 microM, which are significantly smaller than that of cisplatin (30.7 microM) under the same experimental conditions. Furthermore, the cellular uptake of the complexes has been investigated by flow cytometry and laser

  17. Surface sulfonamide modification of poly(N-isopropylacrylamide)-based block copolymer micelles to alter pH and temperature responsive properties for controlled intracellular uptake.

    Science.gov (United States)

    Cyphert, Erika L; von Recum, Horst A; Yamato, Masayuki; Nakayama, Masamichi

    2018-06-01

    Two different surface sulfonamide-functionalized poly(N-isopropylacrylamide)-based polymeric micelles were designed as pH-/temperature-responsive vehicles. Both sulfadimethoxine- and sulfamethazine-surface functionalized micelles were characterized to determine physicochemical properties, hydrodynamic diameters, zeta potentials, temperature-dependent size changes, and lower critical solution temperatures (LCST) in both pH 7.4 and 6.8 solutions (simulating both physiological and mild low pH conditions), and tested in the incorporation of a proof-of-concept hydrophobic antiproliferative drug, paclitaxel. Cellular uptake studies were conducted using bovine carotid endothelial cells and fluorescently labeled micelles to evaluate if there was enhanced cellular uptake of the micelles in a low pH environment. Both variations of micelles showed enhanced intracellular uptake under mildly acidic (pH 6.8) conditions at temperatures slightly above their LCST and minimal uptake at physiological (pH 7.4) conditions. Due to the less negative zeta potential of the sulfamethazine-surface micelles compared to sulfadimethoxine-surface micelles, and the proximity of their LCST to physiological temperature (37°C), the sulfamethazine variation was deemed more amenable for clinically relevant temperature and pH-stimulated applications. Nevertheless, we believe both polymeric micelle variations have the capacity to be implemented as an intracellular drug or gene delivery system in response to mildly acidic conditions. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 1552-1560, 2018. © 2018 Wiley Periodicals, Inc.

  18. Assessing the uptake of arsenic and antimony from contaminated soil by radish (Raphanus sativus) using DGT and selective extractions

    DEFF Research Database (Denmark)

    Ngo, Lien K.; Pinch, Benjamin M.; Bennett, William W.

    2016-01-01

    gradients in thin films technique (DGT) (as CDGT), soil solution analysis, and sequential extraction procedure (SEP). Lability was compared to the bioaccumulation of As and Sb by various compartments of radish (Raphanus sativus) grown in these soils in a pot experiment. Irrespective of the method, all...... of the labile fractions showed that both As and Sb were firmly bound to the solid phases, and that Sb was less mobile than As, although total soil Sb concentrations were higher than total soil As. The bioassay demonstrated low bioaccumulation of As and Sb into R. sativus due to their low lability of As and Sb...... in soils and that there are likely to be differences in their mechanisms of uptake. As accumulated in R. sativus roots was much higher (2.5-21 times) than that of Sb, while the Sb translocated from roots to shoots was approximately 2.5 times higher than that of As. As and Sb in R. sativus tissues were...

  19. The effect of L-cysteine on the portion-selective uptake of cadmium in the renal proximal tubule

    International Nuclear Information System (INIS)

    Murakami, Masataka; Sano, Kenichi; Webb, M.

    1987-01-01

    Cadmium (Cd), co-administered with an excess of L-cysteine, accumulates rapidly in the kidneys of the rat. After subcutaneous (s.c.) injection of 3 μmol CdCl 2 /kg body wt the concentrations of Cd in the blood and kidneys increase with the dose of cysteine over the range 0.06-5.0 mmol/kg body wt. At cysteine doses of less than 1.5 mmol/kg body wt the ratio of the concentrations of Cd in the outer medulla and cortex of the kidney remains the same as that after the injection of Cd alone. This ratio, however, is more than doubled at dose levels of 5-10 mmol cysteine/kg body wt. Hepatic uptake of Cd is unaffected by doses of cysteine below 1.5 mmol/kg body wt but decreases markedly at higher doses. In animals that are dosed simultaneously with 5 mmol cysteine/kg body wt, renal uptake of 109 Cd is known to occur in the straight segments of the proximal tubules. At a dose level of less than 1.5 mmol cysteine/kg body wt the present autoradiographical studies show that 109 Cd is taken up predominantly by the proximal convoluted tubules of the kidney cortex. At the critical dose level (1.5 mmol/kg body wt), cysteine decreases the retention of Cd at the s.c. injection site, but probably has little effect on the distribution of Cd between protein and other carrier molecules in the blood. This distribution, however, is altered at higher cysteine dose levels. It is suggested that, under the latter conditions, stable Cd-cysteine complexes are formed in the blood and are filtered readily through the glomeruli. These complexes are taken up in the kidney at the sites of cysteine reabsorption which, by studies with L-[ 35 S]-cysteine, are identified as the straight segments of the proximal tubules. (orig.)

  20. Uptake and Effects of Six Rare Earth Elements (REEs on Selected Native and Crop Species Growing in Contaminated Soils.

    Directory of Open Access Journals (Sweden)

    David Carpenter

    Full Text Available Rare earth elements (REEs have become increasingly important metals used in modern technology. Processes including mining, oil refining, discarding of obsolete equipment containing REEs, and the use of REE-containing phosphate fertilizers may increase the likelihood of environmental contamination. However, there is a scarcity of information on the toxicity and accumulation of these metals to terrestrial primary producers in contaminated soils. The objective of this work was to assess the phytotoxicity and uptake from contaminated soil of six REEs (chloride forms of praseodymium, neodymium, samarium, terbium, dysprosium, and erbium on three native plants (Asclepias syriaca L., Desmodium canadense (L. DC., Panicum virgatum L. and two crop species (Raphanus sativus L., Solanum lycopersicum L. in separate dose-response experiments under growth chamber conditions. Limited effects of REEs were found on seed germination and speed of germination. Effects on aboveground and belowground biomass were more pronounced, especially for the three native species, which were always more sensitive than the crop species tested. Inhibition concentrations (IC25 and IC50 causing 25 or 50% reductions in plant biomass respectively, were measured. For the native species, the majority of aboveground biomass IC25s (11 out of 18 fell within 100 to 300 mg REE/kg dry soil. In comparison to the native species, IC25s for the crops were always greater than 400 mg REE/kg, with the majority of results (seven out of 12 falling above 700 mg REE/kg. IC50s were often not detected for the crops. Root biomass of native species was also affected at lower doses than in crops. REE uptake by plants was higher in the belowground parts than in the above-ground plant tissues. Results also revealed that chloride may have contributed to the sensitivity of the native species, Desmodium canadense, one of the most sensitive species studied. Nevertheless, these results demonstrated that

  1. Unexpected stimulation of soil methane uptake as emergent property of agricultural soils following bio-based residue application.

    Science.gov (United States)

    Ho, Adrian; Reim, Andreas; Kim, Sang Yoon; Meima-Franke, Marion; Termorshuizen, Aad; de Boer, Wietse; van der Putten, Wim H; Bodelier, Paul L E

    2015-10-01

    Intensification of agriculture to meet the global food, feed, and bioenergy demand entail increasing re-investment of carbon compounds (residues) into agro-systems to prevent decline of soil quality and fertility. However, agricultural intensification decreases soil methane uptake, reducing, and even causing the loss of the methane sink function. In contrast to wetland agricultural soils (rice paddies), the methanotrophic potential in well-aerated agricultural soils have received little attention, presumably due to the anticipated low or negligible methane uptake capacity in these soils. Consequently, a detailed study verifying or refuting this assumption is still lacking. Exemplifying a typical agricultural practice, we determined the impact of bio-based residue application on soil methane flux, and determined the methanotrophic potential, including a qualitative (diagnostic microarray) and quantitative (group-specific qPCR assays) analysis of the methanotrophic community after residue amendments over 2 months. Unexpectedly, after amendments with specific residues, we detected a significant transient stimulation of methane uptake confirmed by both the methane flux measurements and methane oxidation assay. This stimulation was apparently a result of induced cell-specific activity, rather than growth of the methanotroph population. Although transient, the heightened methane uptake offsets up to 16% of total gaseous CO2 emitted during the incubation. The methanotrophic community, predominantly comprised of Methylosinus may facilitate methane oxidation in the agricultural soils. While agricultural soils are generally regarded as a net methane source or a relatively weak methane sink, our results show that methane oxidation rate can be stimulated, leading to higher soil methane uptake. Hence, even if agriculture exerts an adverse impact on soil methane uptake, implementing carefully designed management strategies (e.g. repeated application of specific residues) may

  2. Folate Functionalized Boron Nitride Nanotubes and their Selective Uptake by Glioblastoma Multiforme Cells: Implications for their Use as Boron Carriers in Clinical Boron Neutron Capture Therapy.

    Science.gov (United States)

    Ciofani, Gianni; Raffa, Vittoria; Menciassi, Arianna; Cuschieri, Alfred

    2008-11-25

    Boron neutron capture therapy (BNCT) is increasingly being used in the treatment of several aggressive cancers, including cerebral glioblastoma multiforme. The main requirement for this therapy is selective targeting of tumor cells by sufficient quantities of (10)B atoms required for their capture/irradiation with low-energy thermal neutrons. The low content of boron targeting species in glioblastoma multiforme accounts for the difficulty in selective targeting of this very malignant cerebral tumor by this radiation modality. In the present study, we have used for the first time boron nitride nanotubes as carriers of boron atoms to overcome this problem and enhance the selective targeting and ablative efficacy of BNCT for these tumors. Following their dispersion in aqueous solution by noncovalent coating with biocompatible poly-l-lysine solutions, boron nitride nanotubes were functionalized with a fluorescent probe (quantum dots) to enable their tracking and with folic acid as selective tumor targeting ligand. Initial in vitro studies have confirmed substantive and selective uptake of these nanovectors by glioblastoma multiforme cells, an observation which confirms their potential clinical application for BNCT therapy for these malignant cerebral tumors.

  3. Folate Functionalized Boron Nitride Nanotubes and their Selective Uptake by Glioblastoma Multiforme Cells: Implications for their Use as Boron Carriers in Clinical Boron Neutron Capture Therapy

    Directory of Open Access Journals (Sweden)

    Ciofani Gianni

    2008-01-01

    Full Text Available Abstract Boron neutron capture therapy (BNCT is increasingly being used in the treatment of several aggressive cancers, including cerebral glioblastoma multiforme. The main requirement for this therapy is selective targeting of tumor cells by sufficient quantities of10B atoms required for their capture/irradiation with low-energy thermal neutrons. The low content of boron targeting species in glioblastoma multiforme accounts for the difficulty in selective targeting of this very malignant cerebral tumor by this radiation modality. In the present study, we have used for the first time boron nitride nanotubes as carriers of boron atoms to overcome this problem and enhance the selective targeting and ablative efficacy of BNCT for these tumors. Following their dispersion in aqueous solution by noncovalent coating with biocompatible poly-l-lysine solutions, boron nitride nanotubes were functionalized with a fluorescent probe (quantum dots to enable their tracking and with folic acid as selective tumor targeting ligand. Initial in vitro studies have confirmed substantive and selective uptake of these nanovectors by glioblastoma multiforme cells, an observation which confirms their potential clinical application for BNCT therapy for these malignant cerebral tumors.

  4. Properties of optically selected BL Lacertae candidates from the SDSS

    Science.gov (United States)

    Kügler, S. D.; Nilsson, K.; Heidt, J.; Esser, J.; Schultz, T.

    2014-09-01

    Context. Deep optical surveys open the avenue for finding large numbers of BL Lac objects that are hard to identify because they lack the unique properties classifying them as such. While radio or X-ray surveys typically reveal dozens of sources, recent compilations based on optical criteria alone have increased the number of BL Lac candidates considerably. However, these compilations are subject to biases and may contain a substantial number of contaminating sources. Aims: In this paper we extend our analysis of 182 optically selected BL Lac object candidates from the SDSS with respect to an earlier study. The main goal is to determine the number of bona fide BL Lac objects in this sample. Methods: We examine their variability characteristics, determine their broad-band radio-UV spectral energy distributions (SEDs), and search for the presence of a host galaxy. In addition we present new optical spectra for 27 targets with improved signal-to-noise ratio with respect to the SDSS spectra. Results: At least 59% of our targets have shown variability between SDSS DR2 and our observations by more than 0.1-0.27 mag depending on the telescope used. A host galaxy was detected in 36% of our targets. The host galaxy type and luminosities are consistent with earlier studies of BL Lac host galaxies. Simple fits to broad-band SEDs for 104 targets of our sample derived synchrotron peak frequencies between 13.5 ≤ log 10(νpeak) ≤ 16 with a peak at log 10 ~ 14.5. Our new optical spectra do not reveal any new redshift for any of our objects. Thus the sample contains a large number of bona fide BL Lac objects and seems to contain a substantial fraction of intermediate-frequency peaked BL Lacs. Based on observations collected with the NTT on La Silla (Chile) operated by the European Southern Observatory under proposal 082.B-0133.Based on observations collected at the Centro Astronómico Hispano Alemán (CAHA), operated jointly by the Max-Planck-Institut für Astronomie and the

  5. Unexpected stimulation of soil methane uptake as emergent property of agricultural soils following bio-based residue application

    NARCIS (Netherlands)

    Ho, A.; Reim, A.; Kim, S.Y.; Meima-Franke, M.; Termorshuizen, Aad J; De Boer, W.; Van der Putten, W.H.; Bodelier, P.L.E.

    2015-01-01

    Intensification of agriculture to meet the global food, feed, and bioenergy demand entail increasing re-investment of carbon compounds (residues) into agro-systems to prevent decline of soil quality and fertility. However, agricultural intensification decreases soil methane uptake, reducing and even

  6. Judicial Protection of Private Property Rights in Ethiopia: Selected ...

    African Journals Online (AJOL)

    Hailu_Elias_&_Muradu

    Property Rights Protection and Private Sector Development in Ethiopia” which was .... Even if land has come under public ownership in Ethiopia since 1975, these ... may be capital contributions and in effect, the ownership of the use right over ..... Ethiopian Intellectual Property Office (EIPO) did not hesitate to register this.

  7. The Development and Psychometric Properties of the Selective Mutism Questionnaire

    Science.gov (United States)

    Bergman, R. Lindsey; Keller, Melody L.; Piacentini, John; Bergman, Andrea J.

    2008-01-01

    Research on selective mutism (SM) has been limited by the absence of standardized, psychometrically sound assessment measures. The purpose of our investigation was to present two studies that examined the factor structure and initial reliability and validity of the Selective Mutism Questionnaire (SMQ), a 17-item parent report measure of failure to…

  8. Influence of solvents on properties of solar selective coatings

    Indian Academy of Sciences (India)

    Solar selective coatings for solar thermal flat-plate collectors consisting of crystalline copper oxides and amorphous nickel oxide composites were obtained by robotic spray pyrolyzed deposition. The parameters were optimized for increased spectral selectivity (): high solar absorptance and low thermal emittance.

  9. Early prediction of 90Sr and 137Cs content in edible parts of crops and selection of plants with high uptake ability

    International Nuclear Information System (INIS)

    Zhao Wenhu; Xu Shiming; Hou Lanxin; Shang Zhaorong

    1995-10-01

    The uptake characteristics to 90 Sr and 137 Cs of nine kinds of crops, including spring wheat, rice, soybean, vegetables etc., were studied from seedling to maturity. The change of 90 Sr content per unit of dry weight can be classified into two types--the 90 Sr content kept in the same level during the whole growing season and kept increasing with the growing period until it came to the maximum point at the time of maturity. 90 Sr and 137 Cs in the aerial part of plants were mainly distributed in leaves, but the amounts in seeds and fruits were less. The content of 90 Sr decreased but the content of 137 Cs increased from young to old leaves. So it could be concluded that early prediction of the radioactive content of edible parts according to the content of young leaves was possible. Selection of 169 species in 18 families of plants with high uptake ability of 90 Sr and 137 Cs, which grow in Qinshan region near a nuclear power plant and in Beijing region, is also reported. (8 refs., 6 figs., 16 tabs.)

  10. Did we choose the best one? A new site selection approach based on exposure and uptake potential for waste incineration.

    Science.gov (United States)

    Demirarslan, K Onur; Korucu, M Kemal; Karademir, Aykan

    2016-08-01

    Ecological problems arising after the construction and operation of a waste incineration plant generally originate from incorrect decisions made during the selection of the location of the plant. The main objective of this study is to investigate how the selection method for the location of a new municipal waste incineration plant can be improved by using a dispersion modelling approach supported by geographical information systems and multi-criteria decision analysis. Considering this aim, the appropriateness of the current location of an existent plant was assessed by applying a pollution dispersion model. Using this procedure, the site ranking for a total of 90 candidate locations and the site of the existing incinerator were determined by a new location selection practice and the current place of the plant was evaluated by ANOVA and Tukey tests. This ranking, made without the use of modelling approaches, was re-evaluated based on the modelling of various variables, including the concentration of pollutants, population and population density, demography, temporality of meteorological data, pollutant type, risk formation type by CALPUFF and re-ranking the results. The findings clearly indicate the impropriety of the location of the current plant, as the pollution distribution model showed that its location was the fourth-worst choice among 91 possibilities. It was concluded that the location selection procedures for waste incinerators should benefit from the improvements obtained by the articulation of pollution dispersion studies combined with the population density data to obtain the most suitable location. © The Author(s) 2016.

  11. Rapid screening of selective serotonin re-uptake inhibitors in urine samples using solid-phase microextraction gas chromatography-mass spectrometry.

    Science.gov (United States)

    Salgado-Petinal, Carmen; Lamas, J Pablo; Garcia-Jares, Carmen; Llompart, Maria; Cela, Rafael

    2005-07-01

    In this paper a solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) method is proposed for a rapid analysis of some frequently prescribed selective serotonin re-uptake inhibitors (SSRI)-venlafaxine, fluvoxamine, mirtazapine, fluoxetine, citalopram, and sertraline-in urine samples. The SPME-based method enables simultaneous determination of the target SSRI after simple in-situ derivatization of some of the target compounds. Calibration curves in water and in urine were validated and statistically compared. This revealed the absence of matrix effect and, in consequence, the possibility of quantifying SSRI in urine samples by external water calibration. Intra-day and inter-day precision was satisfactory for all the target compounds (relative standard deviation, RSD, detection limits achieved were detected and tentatively identified.

  12. Selective retrograde labeling of lateral olivocochlear neurons in the brainstem based on preferential uptake of 3H-D-aspartic acid in the cochlea

    International Nuclear Information System (INIS)

    Ryan, A.F.; Schwartz, I.R.; Helfert, R.H.; Keithley, E.; Wang, Z.X.

    1987-01-01

    We have previously shown that perfusion of the gerbil cochlea with probe concentrations of 3 H-D-aspartic acid (D-ASP) results in immediate, selective labeling of 50-60% of the efferent terminals under the inner hair cells, presumably by high-affinity uptake. The present study was undertaken to determine the origin of these endings. Twenty-four hours after cochlear perfusion with D-ASP, labeled neurons were observed in the ipsilateral, and to a much lesser extent in the contralateral, lateral superior olivary nucleus (LSO). The cells were small, primarily fusiform, and showed fewer synaptic contacts than other LSO cells. Combined transport of D-ASP and horseradish peroxidase indicated that all olivocochlear neurons within the LSO that projected to the injected cochlea were labeled by D-ASP. Labeled fibers coursed dorsally from the LSO, joined contralateral fibers that had passed under the floor of the fourth ventricle, and entered the VIIIth nerve root at its ventromedial edge. Adjacent to the ventral cochlear nucleus (VCN), densely labeled collateral fibers crossed the nerve root to enter the VCN. Labeled fibers and terminals were prominent in the central VCN. Neither retrograde transport of D-ASP by medial olivocochlear and vestibular efferents nor anterograde transport by VIIIth nerve afferents was observed. The D-ASP-labeled cells and fibers are clearly lateral olivocochlear efferents. Retrograde transport of D-ASP thus allows the cells, axons, and collaterals of the lateral olivocochlear system to be studied, morphologically, in isolation from other cells that project to the cochlea. Since the olivocochlear neurons are almost certainly cholinergic, retrograde amino acid transport does not necessarily identify the primary neurotransmitter of a neuron. Rather, it indicates the presence of selective uptake by the processes of that neuron at the site of amino acid injection

  13. Selection of lettuce genotypes for phosphorus uptaking efficiency - DOI: 10.4025/actasciagron.v25i1.2348

    OpenAIRE

    Cock, Wallace Rudeck Sthel; UENF; Tardin, Flávio Dessaune; UENF; Amaral Júnior, Antônio Teixeira do; UENF; Scapim, Carlos Alberto; UEM; Amaral, José Francisco Teixeira do; UFES; Cunha, Gláucio de Mello; UFES; Bressan-Smith, Ricardo Enrique; UENF; Pinto, Ronald José Barth; UEM

    2008-01-01

    Nineteen late flowering lettuce genotypes from the UENF horticultural germoplasm bank were evaluated for phosphorus utilization efficiency under a 10 mg.dm-3 P level. A biometrical analysis of genetic parameters and genetic, phenotypic and environment correlations between shoot and root dry matter production, P content in roots and shoot Puptake, P-translocation and P utilization efficiency was undertaken. Genetic variability, which could be promising to obtain positive response to selection,...

  14. Wound Healing Properties of Selected Plants Used in Ethnoveterinary Medicine

    Directory of Open Access Journals (Sweden)

    Amos Marume

    2017-09-01

    Full Text Available Plants have arrays of phytoconstituents that have wide ranging biological effects like antioxidant, anti-inflammatory and antimicrobial properties key in wound management. In vivo wound healing properties of ointments made of crude methanolic extracts (10% extract w/w in white soft paraffin of three plant species, Cissus quadrangularis L. (whole aerial plant parts, Adenium multiflorum Klotzsch (whole aerial plant parts and Erythrina abyssinica Lam. Ex DC. (leaves and bark used in ethnoveterinary medicine were evaluated on BALB/c female mice based on wound area changes, regular observations, healing skin's percentage crude protein content and histological examinations. White soft paraffin and 3% oxytetracycline ointment were used as negative and positive controls, respectively. Wound area changes over a 15 day period for mice treated with C. quadrangularis and A. multiflorum extract ointments were comparable to those of the positive control (oxytetracycline ointment. Wounds managed with the same extract ointments exhibited high crude protein contents, similar to what was observed on animals treated with the positive control. Histological evaluations revealed that C. quadrangularis had superior wound healing properties with the wound area completely returning to normal skin structure by day 15 of the experiment. E. abyssinica leaf and bark extract ointments exhibited lower wound healing properties though the leaf extract exhibited some modest healing properties.

  15. Traits and selection strategies to improve root systems and water uptake in water-limited wheat crops.

    Science.gov (United States)

    Wasson, A P; Richards, R A; Chatrath, R; Misra, S C; Prasad, S V Sai; Rebetzke, G J; Kirkegaard, J A; Christopher, J; Watt, M

    2012-05-01

    Wheat yields globally will depend increasingly on good management to conserve rainfall and new varieties that use water efficiently for grain production. Here we propose an approach for developing new varieties to make better use of deep stored water. We focus on water-limited wheat production in the summer-dominant rainfall regions of India and Australia, but the approach is generally applicable to other environments and root-based constraints. Use of stored deep water is valuable because it is more predictable than variable in-season rainfall and can be measured prior to sowing. Further, this moisture is converted into grain with twice the efficiently of in-season rainfall since it is taken up later in crop growth during the grain-filling period when the roots reach deeper layers. We propose that wheat varieties with a deeper root system, a redistribution of branch root density from the surface to depth, and with greater radial hydraulic conductivity at depth would have higher yields in rainfed systems where crops rely on deep water for grain fill. Developing selection systems for mature root system traits is challenging as there are limited high-throughput phenotyping methods for roots in the field, and there is a risk that traits selected in the lab on young plants will not translate into mature root system traits in the field. We give an example of a breeding programme that combines laboratory and field phenotyping with proof of concept evaluation of the trait at the beginning of the selection programme. This would greatly enhance confidence in a high-throughput laboratory or field screen, and avoid investment in screens without yield value. This approach requires careful selection of field sites and years that allow expression of deep roots and increased yield. It also requires careful selection and crossing of germplasm to allow comparison of root expression among genotypes that are similar for other traits, especially flowering time and disease and toxicity

  16. Comparative short-term effects of sewage sludge and its biochar on soil properties, maize growth and uptake of nutrients on a tropical clay soil in Zimbabwe

    Institute of Scientific and Technical Information of China (English)

    Willis Gwenzi; Moreblessing Muzava; Farai Mapanda; Tonny P Tauro

    2016-01-01

    Soil application of biochar from sewage could potentialy enhance carbon sequestration and close urban nutrient balances. In sub-Saharan Africa, comparative studies investigating plant growth effect and nutrients uptake on tropical soils amended with sewage sludge and its biochar are very limited. A pot experiment was conducted to investigate the effects of sewage sludge and its biochar on soil chemical properties, maize nutrient and heavy metal uptake, growth and biomass partitioning on a tropical clayey soil. The study compared three organic amendments; sewage sludge (SS), sludge biochar (SB) and their combination (SS+SB) to the unamended control and inorganic fertilizers. Organic amendments were applied at a rate of 15 t ha–1 for SS and SB, and 7.5 t ha–1 each for SS and SB. Maize growth, biomass production and nutrient uptake were signiifcantly improved in biochar and sewage sludge amendments compared to the unamended control. Comparable results were observed with F, SS and SS+SB on maize growth at 49 d of sowing. Maize growth for SB, SS, SS+SB and F increased by 42, 53, 47, and 49%, respectively compared to the unamended control. Total biomass for SB, SS, SS+SB, and F increased by 270, 428, 329, and 429%, respectively compared with the unamended control. Biochar amendments reduced Pb, Cu and Zn uptakes by about 22% compared with sludge alone treatment in maize plants. However, there is need for future research based on the current pot experiment to determine whether the same results can be produced under ifeld conditions.

  17. The Properties of Model Selection when Retaining Theory Variables

    DEFF Research Database (Denmark)

    Hendry, David F.; Johansen, Søren

    Economic theories are often fitted directly to data to avoid possible model selection biases. We show that embedding a theory model that specifies the correct set of m relevant exogenous variables, x{t}, within the larger set of m+k candidate variables, (x{t},w{t}), then selection over the second...... set by their statistical significance can be undertaken without affecting the estimator distribution of the theory parameters. This strategy returns the theory-parameter estimates when the theory is correct, yet protects against the theory being under-specified because some w{t} are relevant....

  18. Effects of sewage sludge application on selected soil properties and ...

    African Journals Online (AJOL)

    NSK/2) and one pit on the site that did not (NS/NSK) and described them before collecting soil samples from the genetic horizons of each pit for analysis of soil properties. Soil organic carbon (OC), microbial respiration, electrical conductivity (EC), ...

  19. Physical and Chemical Properties of Some Selected Rice Varieties

    African Journals Online (AJOL)

    User

    Physical and chemical properties of nine rice varieties grown and processed in Ebonyi .... Therefore, one tonne of a slender variety of rice will need more storage space than the ..... during washing and boiling of milled rice Starch 36:386-390.

  20. Combination of soil classification and some selected soil properties ...

    African Journals Online (AJOL)

    The advantage in the combined use of soil classification and top soil analysis for explaining crop yield variation was examined. Soil properties and yields of maize (Zea mays L) on different soil types were measured on farmers' fields for 2 years. Yield prediction improved from 2 per cent at the Order and Association levels to ...

  1. Vapor pressures and thermophysical properties of selected monoterpenoids

    Czech Academy of Sciences Publication Activity Database

    Štejfa, V.; Dergal, F.; Mokbel, I.; Fulem, Michal; Jose, J.; Růžička, K.

    2015-01-01

    Roč. 406, Nov (2015), 124-133 ISSN 0378-3812 Institutional support: RVO:68378271 Keywords : monoterpenoids * vapor pressure * heat capacity * ideal - gas thermodynamic properties * vaporization and sublimation enthalpy Subject RIV: BJ - Thermodynamics Impact factor: 1.846, year: 2015

  2. Physico-chemical properties of oil from some selected underutilized ...

    African Journals Online (AJOL)

    ... Testing and Materials (ASTM) standard specifications for biodiesel production. In actual fact, the iodine values of palm kernel, groundnut, bambara groundnut, pumpkin, African oil bean and sesame, show that they could be used as lubricants and hydraulic brake fluid. Key words: Oil seeds, biodiesel, properties, extraction.

  3. A selection of sensing techniques for mapping soil hydraulic properties

    NARCIS (Netherlands)

    Knotters, M.; Egmond, van F.M.; Bakker, G.; Walvoort, D.J.J.; Brouwer, F.

    2017-01-01

    Data on soil hydraulic properties are needed as input for many models, such as models to predict unsaturated water movement and crop growth, and models to predict leaching of nutrients and pesticides to groundwater. The soil physics database of the Netherlands shows several lacunae, and a

  4. Selection of Minerals properties using service oriented architecture

    Directory of Open Access Journals (Sweden)

    Pavel Horovčák

    2009-09-01

    Full Text Available Continually and impressive amplification of internet technologies development and implementation enables the creationof productive, efficient, useful and interactive web applications. The contribution briefly characterizes SOA (Service OrientedArchitecture, WS (Web Service and AJAX (Asynchronous JavaScript And XML technology and illustrates advantages of AJAX and WSintegration on application example for interactive selection of one or more minerals according to actually chosen selection criteria.Contribution presents three created web services (service for creating of web page’s select list based on given database table content,service for selection of one or a group of minerals according to specified criteria from the group of database tables, and service forcorrect depiction of chemical formulas on web page. The application makes use of two web services on the server side and one webservice plus Ajax technology on the client’s side. Application’s client’s side presents integration of these web services in a dynamic wayby means of Ajax technology and at the same time it is a mashup demonstration.

  5. Between Civil Rights and Property Rights: Debating the Selective ...

    African Journals Online (AJOL)

    What is framed as political contestation today is a culmination of abuses of human rights, including political, civil, social and economic rights. Using a historical analysis, this article points out that there has been selective amnesia in Zimbabwe's human rights discourse, and argues for the equal treatment of civil and political ...

  6. Composition and properties of atmospheric particles in the eastern Atlantic and impacts on gas phase uptake rates

    Directory of Open Access Journals (Sweden)

    G. McFiggans

    2009-12-01

    humidity using HTDMA data. Heterogeneous uptake rates of hypoiodous acid (HOI were also predicted and the nss accumulation mode was found to be the most significant part of the size distribution, which could act as an inert sink for this species. The predicted uptake rates were enhanced by around a factor of 2 during the African influence period due to the addition of both coarse and fine particles.

    The hygroscopicity of the nss fraction was modelled using the Aerosol Diameter Dependent Equilibrium Model (ADDEM using the measured composition and results compared with the HTDMA data. This was the first time such a reconciliation study with this model has been performed with marine data and good agreement was reached within the resolution of the instruments. The effect of hygroscopic growth on HOI uptake was also modelled and ambient uptake rates were found to be approximately doubled compared to equivalent dry particles.

  7. Discovery of Selective Phosphodiesterase 1 Inhibitors with Memory Enhancing Properties.

    Science.gov (United States)

    Dyck, Brian; Branstetter, Bryan; Gharbaoui, Tawfik; Hudson, Andrew R; Breitenbucher, J Guy; Gomez, Laurent; Botrous, Iriny; Marrone, Tami; Barido, Richard; Allerston, Charles K; Cedervall, E Peder; Xu, Rui; Sridhar, Vandana; Barker, Ryan; Aertgeerts, Kathleen; Schmelzer, Kara; Neul, David; Lee, Dong; Massari, Mark Eben; Andersen, Carsten B; Sebring, Kristen; Zhou, Xianbo; Petroski, Robert; Limberis, James; Augustin, Martin; Chun, Lawrence E; Edwards, Thomas E; Peters, Marco; Tabatabaei, Ali

    2017-04-27

    A series of potent thienotriazolopyrimidinone-based PDE1 inhibitors was discovered. X-ray crystal structures of example compounds from this series in complex with the catalytic domain of PDE1B and PDE10A were determined, allowing optimization of PDE1B potency and PDE selectivity. Reduction of hERG affinity led to greater than a 3000-fold selectivity for PDE1B over hERG. 6-(4-Methoxybenzyl)-9-((tetrahydro-2H-pyran-4-yl)methyl)-8,9,10,11-tetrahydropyrido[4',3':4,5]thieno[3,2-e][1,2,4]triazolo[1,5-c]pyrimidin-5(6H)-one was identified as an orally bioavailable and brain penetrating PDE1B enzyme inhibitor with potent memory-enhancing effects in a rat model of object recognition memory.

  8. Assessing Predictive Properties of Genome-Wide Selection in Soybeans

    Directory of Open Access Journals (Sweden)

    Alencar Xavier

    2016-08-01

    Full Text Available Many economically important traits in plant breeding have low heritability or are difficult to measure. For these traits, genomic selection has attractive features and may boost genetic gains. Our goal was to evaluate alternative scenarios to implement genomic selection for yield components in soybean (Glycine max L. merr. We used a nested association panel with cross validation to evaluate the impacts of training population size, genotyping density, and prediction model on the accuracy of genomic prediction. Our results indicate that training population size was the factor most relevant to improvement in genome-wide prediction, with greatest improvement observed in training sets up to 2000 individuals. We discuss assumptions that influence the choice of the prediction model. Although alternative models had minor impacts on prediction accuracy, the most robust prediction model was the combination of reproducing kernel Hilbert space regression and BayesB. Higher genotyping density marginally improved accuracy. Our study finds that breeding programs seeking efficient genomic selection in soybeans would best allocate resources by investing in a representative training set.

  9. Assessing Predictive Properties of Genome-Wide Selection in Soybeans.

    Science.gov (United States)

    Xavier, Alencar; Muir, William M; Rainey, Katy Martin

    2016-08-09

    Many economically important traits in plant breeding have low heritability or are difficult to measure. For these traits, genomic selection has attractive features and may boost genetic gains. Our goal was to evaluate alternative scenarios to implement genomic selection for yield components in soybean (Glycine max L. merr). We used a nested association panel with cross validation to evaluate the impacts of training population size, genotyping density, and prediction model on the accuracy of genomic prediction. Our results indicate that training population size was the factor most relevant to improvement in genome-wide prediction, with greatest improvement observed in training sets up to 2000 individuals. We discuss assumptions that influence the choice of the prediction model. Although alternative models had minor impacts on prediction accuracy, the most robust prediction model was the combination of reproducing kernel Hilbert space regression and BayesB. Higher genotyping density marginally improved accuracy. Our study finds that breeding programs seeking efficient genomic selection in soybeans would best allocate resources by investing in a representative training set. Copyright © 2016 Xavie et al.

  10. Selective labeling of serotonin uptake sites in rat brain by [3H]citalopram contrasted to labeling of multiple sites by [3H]imipramine

    International Nuclear Information System (INIS)

    D'Amato, R.J.; Largent, B.L.; Snowman, A.M.; Snyder, S.H.

    1987-01-01

    Citalopram is a potent and selective inhibitor of neuronal serotonin uptake. In rat brain membranes [ 3 H]citalopram demonstrates saturable and reversible binding with a KD of 0.8 nM and a maximal number of binding sites (Bmax) of 570 fmol/mg of protein. The drug specificity for [ 3 H]citalopram binding and synaptosomal serotonin uptake are closely correlated. Inhibition of [ 3 H]citalopram binding by both serotonin and imipramine is consistent with a competitive interaction in both equilibrium and kinetic analyses. The autoradiographic pattern of [ 3 H]citalopram binding sites closely resembles the distribution of serotonin. By contrast, detailed equilibrium-saturation analysis of [ 3 H]imipramine binding reveals two binding components, i.e., high affinity (KD = 9 nM, Bmax = 420 fmol/mg of protein) and low affinity (KD = 553 nM, Bmax = 8560 fmol/mg of protein) sites. Specific [ 3 H]imipramine binding, defined as the binding inhibited by 100 microM desipramine, is displaced only partially by serotonin. Various studies reveal that the serotonin-sensitive portion of binding corresponds to the high affinity sites of [ 3 H]imipramine binding whereas the serotonin-insensitive binding corresponds to the low affinity sites. Lesioning of serotonin neurons with p-chloroamphetamine causes a large decrease in [ 3 H]citalopram and serotonin-sensitive [ 3 H]imipramine binding with only a small effect on serotonin-insensitive [ 3 H]imipramine binding. The dissociation rate of [ 3 H]imipramine or [ 3 H]citalopram is not altered by citalopram, imipramine or serotonin up to concentrations of 10 microM. The regional distribution of serotonin sensitive [ 3 H]imipramine high affinity binding sites closely resembles that of [ 3 H]citalopram binding

  11. Determination of Properties of Selected Fresh and Processed Medicinal Plants

    Directory of Open Access Journals (Sweden)

    Shirley G. Cabrera

    2015-11-01

    Full Text Available The study aimed to determine the chemical properties, bioactive compounds, antioxidant activity and toxicity level of fresh and processed medicinal plants such as corn (Zea mays silk, pancitpancitan (Peperomiapellucida leaves, pandan (Pandanus amaryllifolius leaves, and commercially available tea. The toxicity level of the samples was measured using the Brine Shrimp Lethality Assay (BSLA. Statistical analysis was done using Statistical Package for Social Sciences (SPSS. Results showed that in terms of chemical properties there is significant difference between fresh and processed corn silk except in crude fiber content was noted. Based on proximate analyses of fresh and processed medicinal plants specifically in terms of % moisture, %crude protein and % total carbohydrates were also observed. In addition, there is also significant difference on bioactive compound contents such as total flavonoids and total phenolics between fresh and processed corn silk except in total vitamin E (TVE content. Pandan and pancit-pancitan showed significant difference in all bioactive compounds except in total antioxidant content (TAC. Fresh pancit-pancitan has the highest total phenolics content (TPC and TAC, while the fresh and processed corn silk has the lowest TAC and TVE content, respectively. Furthermore, results of BSLA for the three medicinal plants and commercially available tea extract showed after 24 hours exposure significant difference in toxicity level was observed. The percentage mortality increased with an increase in exposure time of the three medicinal plants and tea extract. The results of the study can served as baseline data for further processing and commercialization of these medicinal plants.

  12. Antioxidant and Antiradical Properties of Selected Flavonoids and Phenolic Compounds

    Directory of Open Access Journals (Sweden)

    Zübeyir Huyut

    2017-01-01

    Full Text Available Phenolic compounds and flavonoids are known by their antioxidant properties and one of the most important sources for humans is the diet. Due to the harmful effects of synthetic antioxidants such as BHA and BHT, natural novel antioxidants have become the focus of attention for protecting foods and beverages and reducing oxidative stress in vivo. In the current study, we investigated the total antioxidant, metal chelating, Fe3+ and Cu2+ reduction, and free radical scavenging activities of some phenolic and flavonoid compounds including malvin, oenin, ID-8, silychristin, callistephin, pelargonin, 3,4-dihydroxy-5-methoxybenzoic acid, 2,4,6-trihydroxybenzaldehyde, and arachidonoyl dopamine. The antioxidant properties of these compounds at different concentrations (10–30 μg/mL were compared with those of reference antioxidants such as BHA, BHT, α-tocopherol, and trolox. Each substance showed dose-dependent antioxidant activity. Furthermore, oenin, malvin, arachidonoyl dopamine, callistephin, silychristin, and 3,4-dihydroxy-5-methoxybenzoic acid exhibited more effective antioxidant activity than that observed for the reference antioxidants. These results suggest that these novel compounds may function to protect foods and medicines and to reduce oxidative stress in vivo.

  13. Nickel films: Nonselective and selective photochemical deposition and properties

    International Nuclear Information System (INIS)

    Smirnova, N.V.; Boitsova, T.B.; Gorbunova, V.V.; Alekseeva, L.V.; Pronin, V.P.; Kon'uhov, G.S.

    2006-01-01

    Nickel films deposited on quartz surfaces by the photochemical reduction of a chemical nickel plating solution were studied. It was found that the deposition of the films occurs after an induction period, the length of which depends on the composition of the photolyte and the light intensity. Ni particles with a mean diameter of 20-30 nm were detected initially by transmission electron microscopy. The particles then increased in size (50 nm) upon irradiation and grouped into rings consisting of 4-5 particles. Irradiation with high-intensity light produces three-dimensional films. The calculated extinction coefficient of the nickel film was found to be 4800 L mol -1 cm -1 . Electron diffraction revealed that the prepared amorphous nickel films crystallize after one day of storage. It was determined that the films exhibit catalytic activity in the process of nickel deposition from nickel plating solution. The catalytic action remains for about 5-7 min after exposure of the films to air. The processes of selective and nonselective deposition of the nickel films are discussed. The use of poly(butoxy titanium) in the process of selective photochemical deposition enables negative and positive images to be prepared on quartz surfaces

  14. Selected issues of the property right limitation in the criminal proceedings

    OpenAIRE

    Mityukova, Marina

    2014-01-01

    The study aims at an analysis of the relationship between civil law and the criminal procedure law system. The author focus on the limitation of the property right in the selected aspects of the criminal proceedings.

  15. Ionic Selectivity and Permeation Properties of Human PIEZO1 Channels.

    Directory of Open Access Journals (Sweden)

    Radhakrishnan Gnanasambandam

    Full Text Available Members of the eukaryotic PIEZO family (the human orthologs are noted hPIEZO1 and hPIEZO2 form cation-selective mechanically-gated channels. We characterized the selectivity of human PIEZO1 (hPIEZO1 for alkali ions: K+, Na+, Cs+ and Li+; organic cations: TMA and TEA, and divalents: Ba2+, Ca2+, Mg2+ and Mn2+. All monovalent ions permeated the channel. At a membrane potential of -100 mV, Cs+, Na+ and K+ had chord conductances in the range of 35-55 pS with the exception of Li+, which had a significantly lower conductance of ~ 23 pS. The divalents decreased the single-channel permeability of K+, presumably because the divalents permeated slowly and occupied the open channel for a significant fraction of the time. In cell-attached mode, 90 mM extracellular divalents had a conductance for inward currents carried by the divalents of: 25 pS for Ba2+ and 15 pS for Ca2+ at -80 mV and 10 pS for Mg2+ at -50 mV. The organic cations, TMA and TEA, permeated slowly and attenuated K+ currents much like the divalents. As expected, the channel K+ conductance increased with K+ concentration saturating at ~ 45 pS and the KD of K+ for the channel was 32 mM. Pure divalent ion currents were of lower amplitude than those with alkali ions and the channel opening rate was lower in the presence of divalents than in the presence of monovalents. Exposing cells to the actin disrupting reagent cytochalasin D increased the frequency of openings in cell-attached patches probably by reducing mechanoprotection.

  16. In vitro anticancer properties of selected Eucalyptus species.

    Science.gov (United States)

    Bhuyan, Deep Jyoti; Sakoff, Jennette; Bond, Danielle R; Predebon, Melanie; Vuong, Quan V; Chalmers, Anita C; van Altena, Ian A; Bowyer, Michael C; Scarlett, Christopher J

    2017-08-01

    In spite of the recent advancements in oncology, the overall survival rate for pancreatic cancer has not improved over the last five decades. Eucalypts have been linked with cytotoxic and anticancer properties in various studies; however, there is very little scientific evidence that supports the direct role of eucalypts in the treatment of pancreatic cancer. This study assessed the anticancer properties of aqueous and ethanolic extracts of four Eucalyptus species using an MTT assay. The most promising extracts were further evaluated using a CCK-8 assay. Apoptotic studies were performed using a caspase 3/7 assay in MIA PaCa-2 cells. The aqueous extract of Eucalyptus microcorys leaf and the ethanolic extract of Eucalyptus microcorys fruit inhibited the growth of glioblastoma, neuroblastoma, lung and pancreatic cancer cells by more than 80% at 100 μg/mL. The E. microcorys and Eucalyptus saligna extracts showed lower GI 50 values than the ethanolic Eucalyptus robusta extract in MIA PaCa-2 cells. Aqueous E. microcorys leaf and fruit extracts at 100 μg/mL exerted significantly higher cell growth inhibition in MIA PaCa-2 cells than other extracts (p  0.05) were observed in aqueous E. microcorys leaf (86.05 ± 4.75 μg/mL) and fruit (64.66 ± 15.97 μg/mL) and ethanolic E. microcorys leaf (79.30 ± 29.45 μg/mL) extracts in MIA PaCa-2 cells using the CCK-8 assay. Caspase 3/7-mediated apoptosis and morphological changes of cells were also witnessed in MIA PaCa-2 cells after 24 h of treatment with the extracts. This study highlighted the significance of E. microcorys as an important source of phytochemicals with efficacy against pancreatic cancer cells. Further studies are warranted to purify and structurally identify individual compounds and elucidate their mechanisms of action for the development of more potent and specific chemotherapeutic agents for pancreatic cancer.

  17. Electrostatic Properties of Selected Personal Protective Equipment Regarding Explosion Hazard

    Directory of Open Access Journals (Sweden)

    Marcin Jachowicz

    2013-01-01

    Full Text Available In industries such as the mining, petrochemistry or power industries, personal protective equipment is often used in explosive atmospheres. What causes the occurrence of explosive hazards is ever-present in the work environment they include, electrostatic phenomena as well as the build-up of electrical charges on the surface of the protective equipment used. This paper presents the results of studies which were aimed at determining the fundamental electrostatic parameters of protective helmets as well as eye and face protection, surface resistance and the voltage of electrostatic fields. Examinations on the typical structure of the above mentioned equipment was conducted including the variable values of ambient humidity, which can occur in the working environment and with the use of various types of materials used to generate a charge. The adopted methods and testing equipment have been presented. Using the current, general requirements regarding the electrostatic properties of materials, the examined helmets and eye protection were assessed for their use in explosive atmospheres.

  18. SELECTED PROPERTIES OF EPOXY MORTARS WITH PERLITE AGGREGATE

    Directory of Open Access Journals (Sweden)

    Bernardeta Dębska

    2017-01-01

    Full Text Available Contemporarily designed, new polymer concrete-like composites are increasingly often used in construction, particularly where high chemical resistance of the material is important. However, their widespread use is limited, mainly due to the cost of resin binders used. This is a significant problem, especially in a situation where it is necessary to obtain elements of a substantial volume. One solution to this inconvenience is to develop lighter concrete. The article presents a lightweight resin mortar obtained by substitution of sand with expanded perlite. Thanks to its properties, this aggregate allows for the production of a material with a more porous structure, which is highlighted by the received SEM photos. The binder in the mortars was epoxy resin, hardened with triethylenetetramine. The results of the tests carried out allow us to conclude that despite the significant reduction of strength parameters of mortar, we can obtain a material with lower weight, good chemical resistance and low water absorption, and characterized by significant thermal insulation. This type of composites can be used, among others, as cores in sandwich panels.

  19. Antioxidant properties of selected fruit cultivars grown in Sri Lanka.

    Science.gov (United States)

    Silva, K D R R; Sirasa, M S F

    2018-01-01

    Extracts of twenty locally available Sri Lankan fruits were analysed for 2,2-diphenyl-1-picrylhydrazyl (DPPH) scavenging activity, ferrous reducing antioxidant power (FRAP), total phenolic content (TPC), total flavonoid content (TFC) and vitamin C content. The results showed that gooseberry (Phyllanthus emblica 'local') exhibited the highest DPPH scavenging activity (111.25mg ascorbic acid equivalent antioxidant capacity (AEAC)/g), FRAP (1022.05μmol FeSO 4 /g), TPC (915.7mg gallic acid equivalents (GAE)/100g), TFC (873.2mg catechin equivalents (CE)/100g) and vitamin C (136.8mg ascorbic acid equivalents (AAE)/100g), respectively. Sugar apple (Annona squamosa 'local') and star fruit (Averrhoa carambola 'Honey Sweet') obtained the second and third highest antioxidant activities in terms of rankings of FRAP, DPPH activities, TPC, TFC and vitamin C content. Strong correlation between vitamin C, TPC and TFC with FRAP and DPPH showed their contribution to antioxidant capacity. Among the selected fruits, underutilized fruit cultivar gooseberry showed the highest overall antioxidant potential. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Selecting a climate model subset to optimise key ensemble properties

    Directory of Open Access Journals (Sweden)

    N. Herger

    2018-02-01

    Full Text Available End users studying impacts and risks caused by human-induced climate change are often presented with large multi-model ensembles of climate projections whose composition and size are arbitrarily determined. An efficient and versatile method that finds a subset which maintains certain key properties from the full ensemble is needed, but very little work has been done in this area. Therefore, users typically make their own somewhat subjective subset choices and commonly use the equally weighted model mean as a best estimate. However, different climate model simulations cannot necessarily be regarded as independent estimates due to the presence of duplicated code and shared development history. Here, we present an efficient and flexible tool that makes better use of the ensemble as a whole by finding a subset with improved mean performance compared to the multi-model mean while at the same time maintaining the spread and addressing the problem of model interdependence. Out-of-sample skill and reliability are demonstrated using model-as-truth experiments. This approach is illustrated with one set of optimisation criteria but we also highlight the flexibility of cost functions, depending on the focus of different users. The technique is useful for a range of applications that, for example, minimise present-day bias to obtain an accurate ensemble mean, reduce dependence in ensemble spread, maximise future spread, ensure good performance of individual models in an ensemble, reduce the ensemble size while maintaining important ensemble characteristics, or optimise several of these at the same time. As in any calibration exercise, the final ensemble is sensitive to the metric, observational product, and pre-processing steps used.

  1. Selecting a climate model subset to optimise key ensemble properties

    Science.gov (United States)

    Herger, Nadja; Abramowitz, Gab; Knutti, Reto; Angélil, Oliver; Lehmann, Karsten; Sanderson, Benjamin M.

    2018-02-01

    End users studying impacts and risks caused by human-induced climate change are often presented with large multi-model ensembles of climate projections whose composition and size are arbitrarily determined. An efficient and versatile method that finds a subset which maintains certain key properties from the full ensemble is needed, but very little work has been done in this area. Therefore, users typically make their own somewhat subjective subset choices and commonly use the equally weighted model mean as a best estimate. However, different climate model simulations cannot necessarily be regarded as independent estimates due to the presence of duplicated code and shared development history. Here, we present an efficient and flexible tool that makes better use of the ensemble as a whole by finding a subset with improved mean performance compared to the multi-model mean while at the same time maintaining the spread and addressing the problem of model interdependence. Out-of-sample skill and reliability are demonstrated using model-as-truth experiments. This approach is illustrated with one set of optimisation criteria but we also highlight the flexibility of cost functions, depending on the focus of different users. The technique is useful for a range of applications that, for example, minimise present-day bias to obtain an accurate ensemble mean, reduce dependence in ensemble spread, maximise future spread, ensure good performance of individual models in an ensemble, reduce the ensemble size while maintaining important ensemble characteristics, or optimise several of these at the same time. As in any calibration exercise, the final ensemble is sensitive to the metric, observational product, and pre-processing steps used.

  2. Selective cortical decrease of high-affinity choline uptake carrier in Alzheimer's disease: an autoradiographic study using 3H-hemicholinium-3

    International Nuclear Information System (INIS)

    Rodriguez-Puertas, R.; Pazos, A.; Zarranz, J.J.; Pascual, J.

    1994-01-01

    H-hemicholinium-3 (H-HC-3) binding, a marker of the presynaptic high-affinity choline uptake carrier (HACU), was measured by autoradiography in several brain regions of 17 Alzheimer's disease (AD) patients and of 11 matched controls. A significant decrease in the density of H-HC-3 binding sites was found in entorhinal cortex, hippocampus and layers I-III of the frontal cortex. By contrast, in the caudate-putamen the number of H-HC-3 binding sites in AD cases was comparable to that of control striata. These data concur with previous results using classical presynaptic markers and reflect the loss in the activity of HACU, and, hence, in the synthesis of acetylcholine, that selectively occurs in cortical areas of AD brains due to the degeneration of presynaptic cholinergic terminals arising from the basal forebrain. However, the relatively low mean reduction in HACU in cortical areas (-40 %), together with the apparent indemnity of this marker in certain severely demented AD cases, suggest that AD dementia cannot be explained simply by the loss of presynaptic terminals originating in the basal forebrain. These data seem to be a good explanation for the poor response to cholinergic replacement in AD. (author)

  3. A neurobiological perspective on attachment problems in sexual offenders and the role of selective serotonin re-uptake inhibitors in the treatment of such problems.

    Science.gov (United States)

    Beech, Anthony R; Mitchell, Ian J

    2005-02-01

    This paper describes what is currently known about attachment from the development, social-cognitive and biological literatures and outlines the impact on organisms given adverse development experiences that can have an effect upon attachment formation in childhood across these three literatures. We then describe the effects that 'insecure' attachment styles arising in childhood can affect brain chemistry and brain function and subsequently adult social/romantic relationships. In the paper, we note that a number of sexual offenders report adverse childhood experiences and that they possess attachment styles that, taken together, make it likely that they will either seek out intimate attachments in ways where they will have sex with children, perhaps confusing sex with intimacy or in aggressive ways as particularly happens with men who sexually assault adult women. The last section of the paper describes chemical treatment for sexual offenders, focusing on the use of selective serotonin re-uptake inhibitors (SSRIs). We note evidence for the role of SSRIs in promoting more social/affiliative behaviors and speculate on the effects that SSRIs have in the treatment of sexual offenders by targeting areas of the social brain. Here, we would argue that it would be useful to carry out treatment where there is a combination of SSRI treatment (to promote more prosocial feelings and behaviors) in conjunction with therapy that typically addresses thoughts and behaviors, i.e., cognitive-behavioral therapy/schema-focused therapy.

  4. Selective cortical decrease of high-affinity choline uptake carrier in Alzheimer`s disease: an autoradiographic study using {sup 3}H-hemicholinium-3

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez-Puertas, R; Pazos, A [Dept. of Physiology and Pharmacology, Unit of Pharmacology, Univ. of Cantabria, Santander (Spain); Zarranz, J J [Dept. of Neuroscience, Univ. of the Basque Country, Leioa (Spain); Pascual, J [Dept. of Medicine, Service of Neurology, Univ. Hospital ` Marques de Valdecilla` , Univ. of Cantabria, Santander (Spain)

    1994-12-31

    H-hemicholinium-3 (H-HC-3) binding, a marker of the presynaptic high-affinity choline uptake carrier (HACU), was measured by autoradiography in several brain regions of 17 Alzheimer`s disease (AD) patients and of 11 matched controls. A significant decrease in the density of H-HC-3 binding sites was found in entorhinal cortex, hippocampus and layers I-III of the frontal cortex. By contrast, in the caudate-putamen the number of H-HC-3 binding sites in AD cases was comparable to that of control striata. These data concur with previous results using classical presynaptic markers and reflect the loss in the activity of HACU, and, hence, in the synthesis of acetylcholine, that selectively occurs in cortical areas of AD brains due to the degeneration of presynaptic cholinergic terminals arising from the basal forebrain. However, the relatively low mean reduction in HACU in cortical areas (-40 %), together with the apparent indemnity of this marker in certain severely demented AD cases, suggest that AD dementia cannot be explained simply by the loss of presynaptic terminals originating in the basal forebrain. These data seem to be a good explanation for the poor response to cholinergic replacement in AD. (author).

  5. The selective glycine uptake inhibitor org 25935 as an adjunctive treatment to atypical antipsychotics in predominant persistent negative symptoms of schizophrenia: results from the GIANT trial.

    Science.gov (United States)

    Schoemaker, Joep H; Jansen, Wim T; Schipper, Jacques; Szegedi, Armin

    2014-04-01

    Using a selective glycine uptake inhibitor as adjunctive to second-generation antipsychotic (SGA) was hypothesized to ameliorate negative and/or cognitive symptoms in subjects with schizophrenia. Subjects with predominant persistent negative symptoms (previously stabilized ≥3 months on an SGA) were enrolled in a randomized, placebo-controlled trial to investigate adjunctive treatment with Org 25935, a selective inhibitor of type 1 glycine transporter, over 12 weeks in a flexible dose design. Org 25935 was tested at 4 to 8 mg twice daily and 12 to 16 mg twice daily versus placebo. Primary efficacy outcome was mean change from baseline in Scale for Assessment of Negative Symptoms composite score. Secondary efficacy end points were Positive and Negative Syndrome Scale total and subscale scores, depressive symptoms (Calgary Depression Scale for Schizophrenia), global functioning (Global Assessment of Functioning scale), and cognitive measures using a computerized battery (Central Nervous System Vital Signs). Responder rates were assessed post hoc. A total of 215 subjects were randomized, of which 187 (87%) completed the trial. Both dose groups of Org 25935 did not differ significantly from placebo on Scale for Assessment of Negative Symptoms, Positive and Negative Syndrome Scale (total or subscale scores), Global Assessment of Functioning, or the majority of tested cognitive domains. Org 25935 was generally well tolerated within the tested dose range, with no meaningful effects on extrapyramidal symptoms and some reports of reversible visual adverse effects. Org 25935 did not differ significantly from placebo in reducing negative symptoms or improving cognitive functioning when administered as adjunctive treatment to SGA. In our study population, Org 25935 appeared to be well tolerated in the tested dose ranges.

  6. Synthesis selective transport properties of cleft-type ionophores having two convergent hydroxamic acid functions

    International Nuclear Information System (INIS)

    Kim, Duck Hee; Choi, Mi Jung; Chang, Suk Kyu

    2001-01-01

    A series of cleft-type ionophores having two convergent hydroxamic acid functions are prepared and their selective ionophoric properties toward heavy metal and transition metal ions have been investigated. Hydroxamic acids 3 exhibited a prominent selectivity toward heavy metal ions of Hg 2+ and Pb 2+ , and transition metal ions of Cu 2+ over other transition metal and alkaline earth metal ions from slightly acidic source phase (pH 6) to an acidic receiving phase (pH 1). Selective ionophoric properties toward Pb 2+ and Cu 2+ ions over other surveyed metal ions are also confirmed by the FAB-MS measurements

  7. Influence of soil properties and phosphate addition on arsenic uptake from polluted soils by velvetgrass (Holcus lanatus).

    Science.gov (United States)

    Lewińska, K; Karczewska, A

    2013-01-01

    Four kinds of soil material were used in a pot experiment with velvetgrass (Holcus lanatus). Two unpolluted soils: sand (S) and loam (L) were spiked with sodium arsenite (As II) and arsenate (As V), to obtain total arsenic (As) concentrations of 500 mg As kg(-1). Two other soils (ZS I, ZS III), containing 3320 and 5350 mg As kg(-1), were collected from Zloty Stok where gold and arsenic ores were mined and processed for several centuries. The effects of phosphate addition on plants growth and As uptake were investigated. Phosphate was applied to soils in the form of NH4H2PO4 at the rate 0.2 g P/kg. Average concentrations of arsenic in the shoots of velvetgrass grown in spiked soils S and L without P amendment were in the range 18-210 mg As kg(-1) d.wt., whereas those in plants grown on ZS I and ZS II soils were considerably lower, and varied in the range 11-52 mg As kg(-1) d.wt. The addition of phosphate caused a significant increase in plant biomass and therefore the total amounts of As taken up by plants, however, the differences in As concentrations in the shoots of velvetgrass amended and non-amended with phosphate were not statistically significant.

  8. Selection and Physical Properties of High-redshift Galaxies

    Science.gov (United States)

    Fang, G. W.

    2014-09-01

    Extremely Red Objects (EROs) and BzKs continue to attract considerable interest. It has been suggested that they may be the direct progenitors of present-day massive E/S0 galaxies, and can provide crucial constraints on the current galaxy formation and evolution models. Therefore, the key question is to measure the relative fraction of OGs (old galaxies) and DGs (young, and dusty starburst galaxies) in the sample of EROs. Many groups have been currently investigating the fractions of these two ERO populations using a variety of observational approaches, but the fraction of OGs and DGs from different surveys is different. In the meantime, a number of observations suggest that the epoch of z˜2 also plays an important role in galaxy formation and evolution for various reasons: the cosmic star formation rate density (SFRD) begins to drop at z˜2 from a flat plateau at higher redshifts; the morphological type mix of field galaxies changes remarkably at z˜2; the number density of QSOs has a peak at z˜2; and about 50% to 70% of the stellar mass assembly of galaxies took place in the redshift range 1distribution (SED), [3.6]-[8.0] color, and the nonparametric measures of galaxy morphology, we classify EROs into two classes: DGs and OGs. We find that the fraction of OGs and DGs in our sample (COSMOS) is similar, about 52% of them are DGs, and the other 48% are OGs. For 24 EROs in the UDF, 16 fall into DGs, while 8 are OGs. To reduce the redundancy of these three different classification methods, we perform a principal component analysis on the measurements of EROs, and find that the nonparametric measures and SEDs are efficient in segregating DGs and OGs. We investigate the dependence of the fraction of EROs on their observational properties, and the results suggest that DGs become increasingly important toward fainter magnitudes, redder colors, and higher redshifts. Moreover, we find that the clustering of EROs is much stronger than that of full K-limited samples of

  9. Effect of plastic deformation on the magnetic properties of selected austenitic stainless steels

    Directory of Open Access Journals (Sweden)

    Tatiana Oršulová

    2017-04-01

    Full Text Available Austenitic stainless steels are materials, that are widely used in various fields of industry, architecture and biomedicine. Their specific composition of alloying elements has got influence on their deformation behavior. The main goal of this study was evaluation of magnetic properties of selected steels, caused by plastic deformation. The samples were heat treated in different intervals of temperature before measuring. Then the magnetic properties were measured on device designed for measuring of magnetism. From tested specimens, only AISI 304 confirmed effect of plastic deformation on the magnetic properties. Magnetic properties changed with increasing temperature.

  10. Enhanced Selectivity and Uptake Capacity of CO2 and Toluene Adsorption in Co0.5 M0.33 MoS4 (M= Sb or Y) Chalcogels by Impregnated Metal Salts

    KAUST Repository

    Adhiam, Fatima Abdullah Ahmed

    2017-11-17

    The synthesis of metal chalcogenide aerogels Co0.5M0.33MoS4 (M= Sb or Y) by the sol-gel method is reported. In this system, the building blocks [MoS4]2− chelated with Co2+ and (Sb3+) or (Y3+) salts in nonaqueous solvents forming amorphous networks with a gel property. The chalcogels obtained after supercritical drying have BET surface areas of 176 m2 g−1 (Co0.5Sb0.33MoS4) and 145 m2 g−1 (Co0.5Y0.33MoS4). Electron microscopy and physisorption studies reveal that the new materials are porous with wide pore size distribution and average pore width of 16 nm. These chalcogels show higher adsorption capacity of toluene vapor (Co0.5Sb0.33MoS4: 387 mg g−1) and (Co0.5Y0.33MoS4: 304 mg g−1) over cyclohexane vapor and high selectivity of CO2 over CH4 or H2, Co0.5Sb0.33MoS4 (CO2/H2: 80 and CO2/CH4: 21), Co0.5Y0.33MoS4 (CO2/H2: 27 and CO2/CH4: 15). We also demonstrated that the impregnation of various metal species like Li+, Mg2+, and Ni2+ significantly enhanced the uptake capacity and selectivity of toluene and CO2 adsorptions in the chacogels.

  11. Working fluid selection for organic Rankine cycles - Impact of uncertainty of fluid properties

    DEFF Research Database (Denmark)

    Frutiger, Jerome; Andreasen, Jesper Graa; Liu, Wei

    2016-01-01

    of processmodels and constraints 2) selection of property models, i.e. Penge Robinson equation of state 3)screening of 1965 possible working fluid candidates including identification of optimal process parametersbased on Monte Carlo sampling 4) propagating uncertainty of fluid parameters to the ORC netpower output......This study presents a generic methodology to select working fluids for ORC (Organic Rankine Cycles)taking into account property uncertainties of the working fluids. A Monte Carlo procedure is described as a tool to propagate the influence of the input uncertainty of the fluid parameters on the ORC....... The net power outputs of all the feasible working fluids were ranked including their uncertainties. The method could propagate and quantify the input property uncertainty of the fluidproperty parameters to the ORC model, giving an additional dimension to the fluid selection process. In the given analysis...

  12. Characterization and Design of Zeolite Catalysts Solid Acidity, Shape Selectivity and Loading Properties

    CERN Document Server

    Niwa, Miki; Okumura, Kazu

    2010-01-01

    Zeolites are microporous, aluminosilicate minerals commonly used as commercial adsorbents. Zeolite-based catalysts are used by industrial chemical companies in the interconversion of hydrocarbons and the alkylation of aromatic compounds. The current book deals with the characterization of specific properties of Zeolites and calculations for the design of catalysts. Measurements and utilization of solid acidity, shape selectivity, and loading properties, that are three prominent properties of a Zeolite catalyst, are treated in detail. These features concern chemical vapor deposition of silica, shape selectivity, loading properties, solid activity, Brønsted or Lewis character, ammonia temperature programmed desorption, control of the pore-opening size by chemical vapor deposition of silica and XAFS analysis of metals being highly dispersed inside and outside a framework.

  13. Interactive FORTRAN IV computer programs for the thermodynamic and transport properties of selected cryogens (fluids pack)

    Science.gov (United States)

    Mccarty, R. D.

    1980-01-01

    The thermodynamic and transport properties of selected cryogens had programmed into a series of computer routines. Input variables are any two of P, rho or T in the single phase regions and either P or T for the saturated liquid or vapor state. The output is pressure, density, temperature, entropy, enthalpy for all of the fluids and in most cases specific heat capacity and speed of sound. Viscosity and thermal conductivity are also given for most of the fluids. The programs are designed for access by remote terminal; however, they have been written in a modular form to allow the user to select either specific fluids or specific properties for particular needs. The program includes properties for hydrogen, helium, neon, nitrogen, oxygen, argon, and methane. The programs include properties for gaseous and liquid states usually from the triple point to some upper limit of pressure and temperature which varies from fluid to fluid.

  14. Sonochemical surface functionalization of exfoliated LDH: Effect on textural properties, CO2 adsorption, cyclic regeneration capacities and subsequent gas uptake for simultaneous methanol synthesis.

    Science.gov (United States)

    Ezeh, Collins I; Huang, Xiani; Yang, Xiaogang; Sun, Cheng-Gong; Wang, Jiawei

    2017-11-01

    To improve CO 2 adsorption, amine modified Layered double hydroxide (LDH) were prepared via a two stage process, SDS/APTS intercalation was supported by ultrasonic irradiation and then followed by MEA extraction. The prepared samples were characterised using Scanning electron microscope-Energy dispersive X-ray spectroscopy (SEM-EDX), X-ray Photoelectron Spectroscopy (XPS), X-ray diffraction (XRD), Temperature Programmed Desorption (TPD), Brunauer-Emmett-Teller (BET), and Thermogravimetric analysis (TGA), respectively. The characterisation results were compared with those obtained using the conventional preparation method with consideration to the effect of sonochemical functionalization on textural properties, adsorption capacity, regeneration and lifetime of the LDH adsorbent. It is found that LDHs prepared by sonochemical modification had improved pore structure and CO 2 adsorption capacity, depending on sonic intensity. This is attributed to the enhanced deprotonation of activated amino functional groups via the sonochemical process. Subsequently, this improved the amine loading and effective amine efficiency by 60% of the conventional. In addition, the sonochemical process improved the thermal stability of the adsorbent and also, reduced the irreversible CO 2 uptake, CUirrev, from 0.18mmol/g to 0.03mmol/g. Subsequently, improving the lifetime and ease of regenerating the adsorbent respectively. This is authenticated by subjecting the prepared adsorbents to series of thermal swing adsorption (TSA) cycles until its adsorption capacity goes below 60% of the original CO 2 uptake. While the conventional adsorbent underwent a 10 TSA cycles before breaking down, the sonochemically functionalized LDH went further than 30 TSA cycles. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Some properties of copper and selected heavy metal sulfides. A limited literature review

    International Nuclear Information System (INIS)

    Hermansson, H.P.

    1995-06-01

    In the SKB proposal for a Swedish nuclear waste repository, copper canisters are used for encapsulating the spent fuel. The chemical and physical behavior of Copper in the repository environment will therefore be of critical importance for the repository integrity. The present work concerns a literature review of Copper and selected heavy metal sulfides as they are expected to play an important role in the repository environment. The interest is focused on their properties as described by crystal structure, electrical properties, atom mobility, solubility in water, mechanisms of sulfidation and selected thermodynamical data. 56 refs, 14 figs, 5 tabs

  16. Network and neuronal membrane properties in hybrid networks reciprocally regulate selectivity to rapid thalamocortical inputs.

    Science.gov (United States)

    Pesavento, Michael J; Pinto, David J

    2012-11-01

    Rapidly changing environments require rapid processing from sensory inputs. Varying deflection velocities of a rodent's primary facial vibrissa cause varying temporal neuronal activity profiles within the ventral posteromedial thalamic nucleus. Local neuron populations in a single somatosensory layer 4 barrel transform sparsely coded input into a spike count based on the input's temporal profile. We investigate this transformation by creating a barrel-like hybrid network with whole cell recordings of in vitro neurons from a cortical slice preparation, embedding the biological neuron in the simulated network by presenting virtual synaptic conductances via a conductance clamp. Utilizing the hybrid network, we examine the reciprocal network properties (local excitatory and inhibitory synaptic convergence) and neuronal membrane properties (input resistance) by altering the barrel population response to diverse thalamic input. In the presence of local network input, neurons are more selective to thalamic input timing; this arises from strong feedforward inhibition. Strongly inhibitory (damping) network regimes are more selective to timing and less selective to the magnitude of input but require stronger initial input. Input selectivity relies heavily on the different membrane properties of excitatory and inhibitory neurons. When inhibitory and excitatory neurons had identical membrane properties, the sensitivity of in vitro neurons to temporal vs. magnitude features of input was substantially reduced. Increasing the mean leak conductance of the inhibitory cells decreased the network's temporal sensitivity, whereas increasing excitatory leak conductance enhanced magnitude sensitivity. Local network synapses are essential in shaping thalamic input, and differing membrane properties of functional classes reciprocally modulate this effect.

  17. Frequency Selective Properties of Coaxial Transmission Lines Loaded with Combined Artificial Inclusions

    Directory of Open Access Journals (Sweden)

    Francisco Falcone

    2014-01-01

    Full Text Available The properties of a modified coaxial transmission line by periodic inclusions will be discussed. The introduction of split ring resonators, conductor stubs, air gaps, and combination of these gives rise to new frequency selective properties, such as stopband or passband behavior, observable in planar as well as volumetric metamaterial structures. These results envisage new potential applications and implementation of devices in coaxial transmission line technology.

  18. Preliminary Studies on Existing Scenario of Selected Soil Property in Cheddikulam DS Division Vavuniya, Sri Lanka

    OpenAIRE

    M.A. R. Aashifa; P. Loganathan

    2017-01-01

     This study was conducted to quantify the spatial variability of soil properties, use this information to produce accurate map by means of ordinary kriging and find the ways to reclaim the problem soil and make suggestions to cultivate the crop variety which is suitable for the existing soil property.70 sampling points were selected for that research using stratified random sampling method. Stratification was based on the type of land cover, and following land cover patterns were identified f...

  19. Diagnostic properties of three conventional selective plating media for selection of Bacillus cereus, B. thuringiensis and B. weihenstephanensis

    DEFF Research Database (Denmark)

    Hendriksen, Niels Bohse; Hansen, Bjarne Munk

    2011-01-01

    The aim of this study was to assess the diagnostic properties of the two selective plating media and a chromogenic medium for identification of Bacillus cereus. The 324 isolates were B. cereus (37%), Bacillus weihenstephanensis (45%) or Bacillus thuringiensis (18%), as identified by a new...... combination of techniques. All isolates were growing on mannitol–egg yolk–polymyxin agar (MYP), and they did not form acid from mannitol. However, a significant lower number of B. thuringiensis isolates did not show lecithinase activity. All isolates were also growing on polymyxin–egg yolk...... recommended selective plating media MYP and PEMBA for detection of B. cereus group bacteria both have their limitations for identification of some B. cereus, B. weihenstephanensis or B. thuringiensis. However, MYP is preferable compared to PEMBA. The chromogenic medium has its own advantages and limitations...

  20. Study of the thermal properties of selected PCMs for latent heat storage in buildings

    Science.gov (United States)

    Valentova, Katerina; Pechackova, Katerina; Prikryl, Radek; Ostry, Milan; Zmeskal, Oldrich

    2017-07-01

    The paper is focused on measurements of thermal properties of selected phase change materials (PCMs) which can be used for latent heat storage in building structures. The thermal properties were measured by the transient step-wise method and analyzed by the thermal spectroscopy. The results of three different materials (RT18HC, RT28HC, and RT35HC) and their thermal properties in solid, liquid, and phase change region were determined. They were correlated with the differential scanning calorimetry (DSC) measurement. The results will be used to determine the optimum ratio of components for the construction of drywall and plasters containing listed ingredients, respectively.

  1. Hebbian Learning in a Random Network Captures Selectivity Properties of the Prefrontal Cortex

    Science.gov (United States)

    Lindsay, Grace W.

    2017-01-01

    Complex cognitive behaviors, such as context-switching and rule-following, are thought to be supported by the prefrontal cortex (PFC). Neural activity in the PFC must thus be specialized to specific tasks while retaining flexibility. Nonlinear “mixed” selectivity is an important neurophysiological trait for enabling complex and context-dependent behaviors. Here we investigate (1) the extent to which the PFC exhibits computationally relevant properties, such as mixed selectivity, and (2) how such properties could arise via circuit mechanisms. We show that PFC cells recorded from male and female rhesus macaques during a complex task show a moderate level of specialization and structure that is not replicated by a model wherein cells receive random feedforward inputs. While random connectivity can be effective at generating mixed selectivity, the data show significantly more mixed selectivity than predicted by a model with otherwise matched parameters. A simple Hebbian learning rule applied to the random connectivity, however, increases mixed selectivity and enables the model to match the data more accurately. To explain how learning achieves this, we provide analysis along with a clear geometric interpretation of the impact of learning on selectivity. After learning, the model also matches the data on measures of noise, response density, clustering, and the distribution of selectivities. Of two styles of Hebbian learning tested, the simpler and more biologically plausible option better matches the data. These modeling results provide clues about how neural properties important for cognition can arise in a circuit and make clear experimental predictions regarding how various measures of selectivity would evolve during animal training. SIGNIFICANCE STATEMENT The prefrontal cortex is a brain region believed to support the ability of animals to engage in complex behavior. How neurons in this area respond to stimuli—and in particular, to combinations of stimuli (

  2. In planta mechanism of action of leptospermone: impact of its physico-chemical properties on uptake, translocation, and metabolism.

    Science.gov (United States)

    Owens, Daniel K; Nanayakkara, N P Dhammika; Dayan, Franck E

    2013-02-01

    Leptospermone is a natural β-triketone that specifically inhibits the enzyme p-hydrophyphenylpyruvate dioxygenase, the same molecular target site as that of the commercial herbicide mesotrione. The β-triketone-rich essential oil of Leptospermum scoparium has both preemergence and postemergence herbicidal activity, resulting in bleaching of treated plants and dramatic growth reduction. Radiolabeled leptospermone was synthesized to investigate the in planta mechanism of action of this natural herbicide. Approximately 50 % of the absorbed leptospermone was translocated to the foliage suggesting rapid acropetal movement of the molecule. On the other hand, very little leptospermone was translocated away from the point of application on the foliage, indicating poor phloem mobility. These observations are consistent with the physico-chemical properties of leptospermone, such as its experimentally measured logP and pK a values, and molecular mass, number of hydrogen donors and acceptors, and number of rotatable bonds. Consequently, leptospermone is taken up readily by roots and translocated to reach its molecular target site. This provides additional evidence that the anecdotal observation of allelopathic suppression of plant growth under β-triketone-producing species may be due to the release of these phytotoxins in soils.

  3. Selective Iron(III ion uptake using CuO-TiO2 nanostructure by inductively coupled plasma-optical emission spectrometry

    Directory of Open Access Journals (Sweden)

    Rahman Mohammed M

    2012-12-01

    Full Text Available Abstract Background CuO-TiO2 nanosheets (NSs, a kind of nanomaterials is one of the most attracting class of transition doped semiconductor materials due to its interesting and important optical, electrical, and structural properties and has many technical applications, such as in metal ions detection, photocatalysis, Chemi-sensors, bio-sensors, solar cells and so on. In this paper the synthesis of CuO-TiO2 nanosheets by the wet-chemically technique is reported. Methods CuO-TiO2 NSs were prepared by a wet-chemical process using reducing agents in alkaline medium and characterized by UV/vis., FT-IR spectroscopy, X-ray photoelectron spectroscopy (XPS, powder X-ray diffraction (XRD, and field-emission scanning electron microscopy (FE-SEM etc. Results The structural and optical evaluation of synthesized NSs were measured by XRD pattern, Fourier transform infrared (FT-IR and UV–vis spectroscopy, respectively which confirmed that the obtained NSs are well-crystalline CuO-TiO2 and possessing good optical properties. The morphological analysis of CuO-TiO2 NSs was executed by FE-SEM, which confirmed that the doped products were sheet-shaped and growth in large quantity. Here, the analytical efficiency of the NSs was applied for a selective adsorption of iron(III ion prior to detection by inductively coupled plasma-optical emission spectrometry (ICP-OES. The selectivity of NSs towards various metal ions, including Au(III, Cd(II, Co(II, Cr(III, Fe(III, Pd(II, and Zn(II was analyzed. Conclusions Based on the selectivity study, it was confirmed that the selectivity of doped NSs phase was the most towards Fe(III ion. The static adsorption capacity for Fe(III was calculated to be 110.06 mgg−1. Results from adsorption isotherm also verified that the adsorption process was mainly monolayer-adsorption onto a surface containing a finite number of CuO-TiO2 NSs adsorption sites.

  4. Selection harvests in Amazonian rainforests: long-term impacts on soil properties

    Science.gov (United States)

    K.L. McNabb; M.S. Miller; B.G. Lockaby; B.J. Stokes; R.G. Clawson; John A. Stanturf; J.N.M. Silva

    1997-01-01

    Surface soil properties were compared among disturbance classes associated with a single-tree selection harvest study installed in 1979 in the Brazilian Amazon. Response variables included pH, total N, total organic C, extractable P, exchangeable K, Ca, Mg, and bulk density. In general, concentrations of all elements displayed residual effects 16 years after harvests...

  5. From selective to highly selective SSRIs: a comparison of the antinociceptive properties of fluoxetine, fluvoxamine, citalopram and escitalopram.

    Science.gov (United States)

    Schreiber, Shaul; Pick, Chaim G

    2006-08-01

    Most Serotonin Selective Reuptake Inhibitors (SSRIs) have been found to possess secondary binding properties, while citalopram and its S-enantiomer (escitalopram) have been reconfirmed "purest SSRIs". Using the mouse model of acute pain hotplate analgesia meter, we evaluated the antinociceptive properties of fluoxetine, fluvoxamine, citalopram and escitalopram, injected i.p. Fluvoxamine induced a dose-dependent clear antinociceptive effect (with an ED(50) value of 6.4 mg/kg). Both fluoxetine and citalopram induced (separately) only a weak antinociceptive effect with an inverse "U" shape curve. All three drug's effects were not abolished by naloxone. Escitalopram did not elicit any effect at quasi-equipotent doses. These findings show that fluoxetine, fluvoxamine and citalopram given i.p. are weak antinociceptors, (not mediated through opioid mechanisms), while escitalopram possesses no antinociceptive properties when injected i.p. This difference between citalopram and escitalopram calls for further studies in order to assess the various differences between the two enantiomers of citalopram, and between each enantiomer and the racemic mixture.

  6. Dose selection for radioiodine therapy of borderline hyperthyroid patients with multifocal and disseminated autonomy on the basis of {sup 99m}Tc-pertechnetate thyroid uptake

    Energy Technology Data Exchange (ETDEWEB)

    Reinhardt, Michael J.; Mallek, Dirk von; Manka-Waluch, Agnieszka; Palmedo, Holger [Department of Nuclear Medicine, University Hospital Bonn (Germany); Joe, Alexius; Zimmerlin, Martina [Department of Nuclear Medicine, University Hospital Freiburg (Germany); Krause, Thomas M. [Department of Nuclear Medicine, Inselspital Bern (Switzerland)

    2002-04-01

    The aim of this study was to optimise radioiodine therapy of diffuse and nodular toxic goitre by calculation of the radiation dose delivered to the thyroid on the basis of the pretreatment technetium-99m pertechnetate thyroid uptake under thyrotropin suppression (TcTU{sub s}). The TcTU{sub s} value serves as a substitute for the non-suppressible iodine turnover and the functional autonomous mass. Marinelli's formula was used to calculate tissue absorbed doses of 150 Gy, 200 Gy, 250 Gy and 300 Gy to the thyroids of 438 patients with multifocal and disseminated autonomy. The mean age of patients was 70{+-}9 years, and the mean thyroid volume was 54{+-}26 ml. Two hundred and sixty-one of the patients had at least one documented previous episode of overt hyperthyroidism. Tissue absorbed doses were adapted to the pretreatment TcTU{sub s}: 150 Gy for a TcTU{sub s} of 1.5%-2.49%, 200 Gy for a TcTU{sub s} of 2.5%-3.49%, 250 Gy for a TcTU{sub s} of 3.5%-4.49% and 300 Gy for a TcTU{sub s} of {>=}4.5%. Normalisation of TcTU{sub s} and thyrotropin (TSH), thyroid volume reduction and frequency of hypothyroidism and recurrent hyperthyroidism were evaluated 1 year after a single radioiodine therapy. The presented dose strategy resulted in normalisation of TcTU{sub s} in 96% and an increase in TSH to the normal range in 92%. Recurrent hyperthyroidism was observed in only five patients. Thyroid volume decreased from 54{+-}26 before treatment to 34{+-}20 ml, a mean reduction of 37%. The frequency of hypothyroidism, at 0.9%, was encouragingly low. Dose selection in accordance with pretreatment TcTU{sub s} can be recommended for elimination of functional autonomous tissue with a single radioiodine therapy in patients of advanced age with enlarged thyroid glands and relevant autonomous masses who are at risk of developing iodine-induced hyperthyroidism. (orig.)

  7. Dose selection for radioiodine therapy of borderline hyperthyroid patients with multifocal and disseminated autonomy on the basis of 99mTc-pertechnetate thyroid uptake

    International Nuclear Information System (INIS)

    Reinhardt, Michael J.; Mallek, Dirk von; Manka-Waluch, Agnieszka; Palmedo, Holger; Joe, Alexius; Zimmerlin, Martina; Krause, Thomas M.

    2002-01-01

    The aim of this study was to optimise radioiodine therapy of diffuse and nodular toxic goitre by calculation of the radiation dose delivered to the thyroid on the basis of the pretreatment technetium-99m pertechnetate thyroid uptake under thyrotropin suppression (TcTU s ). The TcTU s value serves as a substitute for the non-suppressible iodine turnover and the functional autonomous mass. Marinelli's formula was used to calculate tissue absorbed doses of 150 Gy, 200 Gy, 250 Gy and 300 Gy to the thyroids of 438 patients with multifocal and disseminated autonomy. The mean age of patients was 70±9 years, and the mean thyroid volume was 54±26 ml. Two hundred and sixty-one of the patients had at least one documented previous episode of overt hyperthyroidism. Tissue absorbed doses were adapted to the pretreatment TcTU s : 150 Gy for a TcTU s of 1.5%-2.49%, 200 Gy for a TcTU s of 2.5%-3.49%, 250 Gy for a TcTU s of 3.5%-4.49% and 300 Gy for a TcTU s of ≥4.5%. Normalisation of TcTU s and thyrotropin (TSH), thyroid volume reduction and frequency of hypothyroidism and recurrent hyperthyroidism were evaluated 1 year after a single radioiodine therapy. The presented dose strategy resulted in normalisation of TcTU s in 96% and an increase in TSH to the normal range in 92%. Recurrent hyperthyroidism was observed in only five patients. Thyroid volume decreased from 54±26 before treatment to 34±20 ml, a mean reduction of 37%. The frequency of hypothyroidism, at 0.9%, was encouragingly low. Dose selection in accordance with pretreatment TcTU s can be recommended for elimination of functional autonomous tissue with a single radioiodine therapy in patients of advanced age with enlarged thyroid glands and relevant autonomous masses who are at risk of developing iodine-induced hyperthyroidism. (orig.)

  8. Working fluid selection for organic Rankine cycles - Impact of uncertainty of fluid properties

    DEFF Research Database (Denmark)

    Frutiger, Jerome; Andreasen, Jesper Graa; Liu, Wei

    2016-01-01

    This study presents a generic methodology to select working fluids for ORC (Organic Rankine Cycles)taking into account property uncertainties of the working fluids. A Monte Carlo procedure is described as a tool to propagate the influence of the input uncertainty of the fluid parameters on the ORC...... modeloutput, and provides the 95%-confidence interval of the net power output with respect to the fluid property uncertainties. The methodology has been applied to a molecular design problem for an ORCusing a low-temperature heat source and consisted of the following four parts: 1) formulation...... of processmodels and constraints 2) selection of property models, i.e. Penge Robinson equation of state 3)screening of 1965 possible working fluid candidates including identification of optimal process parametersbased on Monte Carlo sampling 4) propagating uncertainty of fluid parameters to the ORC netpower output...

  9. Neuromodulatory properties of fluorescent carbon dots: effect on exocytotic release, uptake and ambient level of glutamate and GABA in brain nerve terminals.

    Science.gov (United States)

    Borisova, Tatiana; Nazarova, Anastasia; Dekaliuk, Mariia; Krisanova, Natalia; Pozdnyakova, Natalia; Borysov, Arsenii; Sivko, Roman; Demchenko, Alexander P

    2015-02-01

    Carbon dots (C-dots), a recently discovered class of fluorescent nano-sized particles with pure carbon core, have great bioanalytical potential. Neuroactive properties of fluorescent C-dots obtained from β-alanine by microwave heating were assessed based on the analysis of their effects on the key characteristics of GABA- and glutamatergic neurotransmission in isolated rat brain nerve terminals. It was found that C-dots (40-800 μg/ml) in dose-dependent manner: (1) decreased exocytotic release of [(3)H]GABA and L-[(14)C]glutamate; (2) reduced acidification of synaptic vesicles; (3) attenuated the initial velocity of Na(+)-dependent transporter-mediated uptake of [(3)H]GABA and L-[(14)C]glutamate; (4) increased the ambient level of the neurotransmitters, nevertheless (5) did not change significantly the potential of the plasma membrane of nerve terminals. Almost complete suppression of exocytotic release of the neurotransmitters was caused by C-dots at a concentration of 800 μg/ml. Fluorescent and neuromodulatory features combined in C-dots create base for their potential usage for labeling and visualization of key processes in nerve terminals, and also in theranostics. In addition, natural presence of carbon-containing nanoparticles in the human food chain and in the air may provoke the development of neurologic consequences. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. SELECTED PHYSICAL PROPERTIES OF EXTRUDED COMPOSITES TYPE OF POROUS PVC-METAL

    Directory of Open Access Journals (Sweden)

    Aneta Tor-Świątek

    2014-09-01

    Full Text Available The article presents studies of selected physical and mechanical properties of hybrid materials type of polymer-metal. In the frame of this work modification of PVC with the iron and copper powder in amount of 0, 1.5 and 3% and blowing agent in amount of 0, 0.5, 1% was done. Extrudates in a form of pipe were tested to determine density, porosity, maximum tensile stress, stress at break, modulus of elasticity and elongation with break. The samples were also observed in a microscope. The studies have shown significant influence of the added components on the properties tested.

  11. Chemical-technological approach to the selection of ceramic materials with predetermined thermistor properties

    Energy Technology Data Exchange (ETDEWEB)

    Plewa, J.; Altenburg, H. [Fachhochschule Muenster, Steinfurt (Germany). SIMa and Supraleiter-Keramik-Kristalle; Brunner, M. [Fachhochschule Koeln (Germany). Elektronische Bauelemente; Shpotyuk, O.; Vakiv, M. [Scientific Research Co. ' ' Carat' ' , Lviv Scientific Research Inst. of Materials, Lviv (Ukraine)

    2002-07-01

    The selection possibilities of quaternary Cu-Ni-Co-Mn oxide system restricted by cubic spinels (CuMn{sub 2}O{sub 4}, MnCo{sub 2}O{sub 4} and NiMn{sub 2}O{sub 4}) for NTC thermistors application were discussed. Phase compositions, microstructural features and electrical properties of the investigated spinel-structured ceramics were studied in tight connection with technological regimes of their sintering. (orig.)

  12. Surface-anchored poly(acryloyl-L(D)-valine) with enhanced chirality-selective effect on cellular uptake of gold nanoparticles

    Science.gov (United States)

    Deng, Jun; Wu, Sai; Yao, Mengyun; Gao, Changyou

    2016-01-01

    Chirality is one of the ubiquitous phenomena in biological systems. The left handed (L-) amino acids and right handed (D-) sugars are normally found in proteins, and in RNAs and DNAs, respectively. The effect of chiral surfaces at the nanoscale on cellular uptake has, however, not been explored. This study reveals for the first time the molecular chirality on gold nanoparticles (AuNPs) functions as a direct regulator for cellular uptake. Monolayers of 2-mercaptoacetyl-L(D)-valine (L(D)-MAV) and poly(acryloyl-L(D)-valine (L(D)-PAV) chiral molecules were formed on AuNPs surface, respectively. The internalized amount of PAV-AuNPs was several times larger than that of MAV-AuNPs by A549 and HepG2 cells, regardless of the chirality difference. However, the D-PAV-AuNPs were internalized with significantly larger amount than the L-PAV-AuNPs. This chirality-dependent uptake effect is likely attributed to the preferable interaction between the L-phospholipid-based cell membrane and the D-enantiomers. PMID:27531648

  13. Microstructure and Magnetic Properties of Magnetic Material Fabricated by Selective Laser Melting

    Science.gov (United States)

    Jhong, Kai Jyun; Huang, Wei-Chin; Lee, Wen Hsi

    Selective Laser Melting (SLM) is a powder-based additive manufacturing which is capable of producing parts layer-by-layer from a 3D CAD model. The aim of this study is to adopt the selective laser melting technique to magnetic material fabrication. [1]For the SLM process to be practical in industrial use, highly specific mechanical properties of the final product must be achieved. The integrity of the manufactured components depend strongly on each single laser-melted track and every single layer, as well as the strength of the connections between them. In this study, effects of the processing parameters, such as the space distance of surface morphology is analyzed. Our hypothesis is that when a magnetic product is made by the selective laser melting techniques instead of traditional techniques, the finished component will have more precise and effective properties. This study analyzed the magnitudes of magnetic properties in comparison with different parameters in the SLM process and compiled a completed product to investigate the efficiency in contrast with products made with existing manufacturing processes.

  14. Microstructure and mechanical properties of selective laser melted Ti6Al4V alloy

    Science.gov (United States)

    Losertová, M.; Kubeš, V.

    2017-11-01

    The present work was focused on the properties of porous Ti6Al4V specimens processed by selective laser melting (SLM) and tested in tension and compression before and after heat treatment. The SLM samples were annealed at 955 °C, water quenched and aged at 600 °C with following air cooling. The values of the mechanical tests showed that the samples exhibited high mechanical properties. The anisotropy of tensile and compressive strength was observed, which was related to the occurrence of voids. The plastic properties of specimens were improved by means of the heat treatment that led to the transformation of martensitic to lamellar structure composed of α + β phases. The microstructure of SLM samples were evaluated before and after the heat treatment. The brittle nature of failures of non-heat treated samples can be explained by synergy of martensite presence, microcracks and residual stresses produced by SLM.

  15. Neuronal Uptake and Neuroprotective Properties of Curcumin-Loaded Nanoparticles on SK-N-SH Cell Line: Role of Poly(lactide-co-glycolide) Polymeric Matrix Composition.

    Science.gov (United States)

    Djiokeng Paka, Ghislain; Doggui, Sihem; Zaghmi, Ahlem; Safar, Ramia; Dao, Lé; Reisch, Andreas; Klymchenko, Andrey; Roullin, V Gaëlle; Joubert, Olivier; Ramassamy, Charles

    2016-02-01

    Curcumin, a neuroprotective agent with promising therapeutic approach has poor brain bioavailability. Herein, we demonstrate that curcumin-encapsulated poly(lactide-co-glycolide) (PLGA) 50:50 nanoparticles (NPs-Cur 50:50) are able to prevent the phosphorylation of Akt and Tau proteins in SK-N-SH cells induced by H2O2 and display higher anti-inflammatory and antioxidant activities than free curcumin. PLGA can display various physicochemical and degradation characteristics for controlled drug release applications according to the matrix used. We demonstrate that the release of curcumin entrapped into a PLGA 50:50 matrix (NPs-Cur 50:50) is faster than into PLGA 65:35. We have studied the effects of the PLGA matrix on the expression of some key antioxidant- and neuroprotective-related genes such as APOE, APOJ, TRX, GLRX, and REST. NPs-Cur induced the elevation of GLRX and TRX while decreasing APOJ mRNA levels and had no effect on APOE and REST expressions. In the presence of H2O2, both NPs-Cur matrices are more efficient than free curcumin to prevent the induction of these genes. Higher uptake was found with NPs-Cur 50:50 than NPs-Cur 65:35 or free curcumin. By using PLGA nanoparticles loaded with the fluorescent dye Lumogen Red, we demonstrated that PLGA nanoparticles are indeed taken up by neuronal cells. These data highlight the importance of polymer composition in the therapeutic properties of the nanodrug delivery systems. Our study demonstrated that NPs-Cur enhance the action of curcumin on several pathways implicated in the pathophysiology of Alzheimer's disease (AD). Overall, these results suggest that PLGA nanoparticles are a promising strategy for the brain delivery of drugs for the treatment of AD.

  16. Synthesis and magnetic properties of size-selected CoPt nanoparticles

    International Nuclear Information System (INIS)

    Tournus, F.; Blanc, N.; Tamion, A.; Hillenkamp, M.; Dupuis, V.

    2011-01-01

    CoPt nanoparticles are widely studied, in particular for their potentially very high magnetic anisotropy. However, their magnetic properties can differ from the bulk ones and they are expected to vary with the particle size. In this paper, we report the synthesis and characterization of well-defined CoPt nanoparticle samples produced in ultrahigh vacuum conditions following a physical route: the mass-selected low energy cluster beam deposition technique. This approach relies on an electrostatic deviation of ionized clusters which allows us to easily adjust the particle size, independently from the deposited equivalent thickness (i.e. the surface or volume particle density in a sample). Diluted samples made of CoPt particles, with different diameters, embedded in amorphous carbon are studied by transmission electron microscopy and superconducting interference device magnetometry, which gives access to the magnetic anisotropy energy distribution. We then compare the magnetic properties of two different particle sizes. The results are found to be consistent with an anisotropy constant (including its distribution) which does not evolve with the particle size in the range considered. - Highlights: → Samples of mass-selected CoPt nanoparticles are synthesized by an original physical method. → The magnetic properties of two different particle sizes are compared. → The anisotropy constant (including its dispersion) does not evolve in the range considered. → These results illustrate some invariance properties of ZFC curves.

  17. Selected mechanical properties of aluminum composite materials reinforced with SiC particles

    Directory of Open Access Journals (Sweden)

    A. Kurzawa

    2008-07-01

    Full Text Available This work presents the results of research concerning influence of ceramic particles’ content of silicon carbide on selected mechanical properties of type AW-AlCu4Mg2Mn - SiC composite materials. Composites produced of SiC particles with pressure infiltration method of porous preform and subject to hot plastic forming in the form of open die forging were investigated. The experimental samples contained from 5% up to 45% of reinforcing SiC particles of 8÷10μm diameter. Studies of strength properties demonstrated that the best results, in case of tensile strength as well as offset yield strength, might be obtained while applying reinforcement in the amount of 20-25% vol. of SiC. Application of higher than 25% vol. contents of reinforcing particles leads to gradual strength loss. The investigated composites were characterized by very high functional properties, such as hardness and abrasive wear resistance, whose values increase strongly with the increase of reinforcement amount. The presented results of the experiments shall allow for a more precise component selection of composite materials at the stage of planning and design of their properties.

  18. Properties of Neurons in External Globus Pallidus Can Support Optimal Action Selection

    Science.gov (United States)

    Bogacz, Rafal; Martin Moraud, Eduardo; Abdi, Azzedine; Magill, Peter J.; Baufreton, Jérôme

    2016-01-01

    The external globus pallidus (GPe) is a key nucleus within basal ganglia circuits that are thought to be involved in action selection. A class of computational models assumes that, during action selection, the basal ganglia compute for all actions available in a given context the probabilities that they should be selected. These models suggest that a network of GPe and subthalamic nucleus (STN) neurons computes the normalization term in Bayes’ equation. In order to perform such computation, the GPe needs to send feedback to the STN equal to a particular function of the activity of STN neurons. However, the complex form of this function makes it unlikely that individual GPe neurons, or even a single GPe cell type, could compute it. Here, we demonstrate how this function could be computed within a network containing two types of GABAergic GPe projection neuron, so-called ‘prototypic’ and ‘arkypallidal’ neurons, that have different response properties in vivo and distinct connections. We compare our model predictions with the experimentally-reported connectivity and input-output functions (f-I curves) of the two populations of GPe neurons. We show that, together, these dichotomous cell types fulfil the requirements necessary to compute the function needed for optimal action selection. We conclude that, by virtue of their distinct response properties and connectivities, a network of arkypallidal and prototypic GPe neurons comprises a neural substrate capable of supporting the computation of the posterior probabilities of actions. PMID:27389780

  19. Temporal dependence of the selectivity property of SES stations in western Greece

    Directory of Open Access Journals (Sweden)

    E. Dologlou

    2009-06-01

    Full Text Available The selectivity property of the SES stations, IOA, PIR and PAT in western Greece, based on reported precursory SES signals and associated large earthquakes (Mw≥5.4 that occurred from 1983 to the end of 2008, has been examined. Interesting temporal dependence of the sensitive ability of these stations has been unveiled. Physical mechanisms for the observed changes in selectivity might be related with tectonic and geodynamic events. For instance, selectivity for IOA exhibits a time dependence, for PAT probably is related to the activation of Wadati-Benioff zone while for PIR seems to be related to the specific tectonics of two confined areas such as the Cephalonia Transform Faulting zone in Ionian Sea and the southwestern part of the Hellenic Trench.

  20. Experimental Comparison of the Tribological Properties of Selected Surfaces Created by Thermal Spraying Technology

    Directory of Open Access Journals (Sweden)

    František Tóth

    2016-01-01

    Full Text Available The scientific article titled “Experimental comparison of the tribological properties of selected surfaces created by thermal spraying technology” deals with the surface condition of selected pairs working within the mixed friction before and after experimental tests. Based on the chosen methodology, the experimental tests were performed on the Tribotestor M’06 testing machine. The ecological oil MOGUL HEES 46 (manufactured by Paramo was used as a lubricant. The tests were performed on selected material pairs. The first friction element was a shaft of steel 14 220. The second friction element was a steel plate of steel 11 373 with a friction surface created by two materials, i.e. CuSn10 and NP 40. The results are statistically elaborated and illustrated in figures and tables.

  1. A large sample of Kohonen-selected SDSS quasars with weak emission lines: selection effects and statistical properties

    Science.gov (United States)

    Meusinger, H.; Balafkan, N.

    2014-08-01

    Aims: A tiny fraction of the quasar population shows remarkably weak emission lines. Several hypotheses have been developed, but the weak line quasar (WLQ) phenomenon still remains puzzling. The aim of this study was to create a sizeable sample of WLQs and WLQ-like objects and to evaluate various properties of this sample. Methods: We performed a search for WLQs in the spectroscopic data from the Sloan Digital Sky Survey Data Release 7 based on Kohonen self-organising maps for nearly 105 quasar spectra. The final sample consists of 365 quasars in the redshift range z = 0.6 - 4.2 (z¯ = 1.50 ± 0.45) and includes in particular a subsample of 46 WLQs with equivalent widths WMg iiattention was paid to selection effects. Results: The WLQs have, on average, significantly higher luminosities, Eddington ratios, and accretion rates. About half of the excess comes from a selection bias, but an intrinsic excess remains probably caused primarily by higher accretion rates. The spectral energy distribution shows a bluer continuum at rest-frame wavelengths ≳1500 Å. The variability in the optical and UV is relatively low, even taking the variability-luminosity anti-correlation into account. The percentage of radio detected quasars and of core-dominant radio sources is significantly higher than for the control sample, whereas the mean radio-loudness is lower. Conclusions: The properties of our WLQ sample can be consistently understood assuming that it consists of a mix of quasars at the beginning of a stage of increased accretion activity and of beamed radio-quiet quasars. The higher luminosities and Eddington ratios in combination with a bluer spectral energy distribution can be explained by hotter continua, i.e. higher accretion rates. If quasar activity consists of subphases with different accretion rates, a change towards a higher rate is probably accompanied by an only slow development of the broad line region. The composite WLQ spectrum can be reasonably matched by the

  2. The selective dopamine uptake inhibitor, D-84, suppresses cocaine self-administration, but does not occasion cocaine-like levels of generalization.

    Science.gov (United States)

    Batman, Angela M; Dutta, Aloke K; Reith, Maarten E A; Beardsley, Patrick M

    2010-12-01

    A successful replacement pharmacotherapy for treating cocaine dependency would likely reduce cocaine's abuse, support a low abuse liability, overlap cocaine's subjective effects, and have a long duration of action. Inhibitors with varying selectivity at the dopamine transporter (DAT) have approximated these properties. The objective of the present study was to characterize the behavioural effects of an extremely selective DAT inhibitor, (+) trans-4-(2-Benzhydryloxyethyl)-1-(4-fluorobenzyl) piperadin-3-ol (D-84), a 3-hydroxy substituted piperidine derivative of GBR-12935, for its cocaine-like discriminative stimulus effects, its effects on cocaine self-administration, and for its own self-administration. During cocaine discrimination tests, cocaine occasioned the 10 mg/kg cocaine training stimulus with an ED(50) value of 3.13 (1.54-6.34) mg/kg, and reduced response rates with an ED(50) value of 20.39 (7.24-57.44) mg/kg. D-84 incompletely generalized to the cocaine stimulus occasioning a maximal 76% cocaine-lever responding, while reducing response rates with lower potency than cocaine (ED(50)=30.94 (12.34-77.60) mg/kg). Pretreatment with D-84 (9.6-30.4 mg/kg) significantly (P<0.05) reduced cocaine intake at 17.1 mg/kg D-84 when cocaine was self-administered at 0.5 mg/kg/infusion, and at 30.4 mg/kg D-84 when cocaine was self-administered at 0.1, 0.5 .and 1.0 mg/kg/infusion. During self-administration tests with D-84 (0.1-1 mg/kg/infusion), numbers of infusions significantly exceeded vehicle levels at 0.3 mg/kg/infusion. These results show that D-84 pretreatment can decrease cocaine intake especially when high doses of cocaine are being self-administered. This observation, combined with its incomplete generalization to the cocaine discriminative stimulus and its reported long duration of action, provides a profile consistent with a potential replacement therapy for treating cocaine-abusing patients. Copyright © 2010 Elsevier B.V. All rights reserved.

  3. Surface properties and corrosion behavior of Co-Cr alloy fabricated with selective laser melting technique.

    Science.gov (United States)

    Xin, Xian-zhen; Chen, Jie; Xiang, Nan; Wei, Bin

    2013-01-01

    We sought to study the corrosion behavior and surface properties of a commercial cobalt-chromium (Co-Cr) alloy which was fabricated with selective laser melting (SLM) technique. For this purpose, specimens were fabricated using different techniques, such as SLM system and casting methods. Surface hardness testing, microstructure observation, surface analysis using X-ray photoelectron spectroscopy (XPS) and electrochemical corrosion test were carried out to evaluate the corrosion properties and surface properties of the specimens. We found that microstructure of SLM specimens was more homogeneous than that of cast specimens. The mean surface hardness values of SLM and cast specimens were 458.3 and 384.8, respectively; SLM specimens showed higher values than cast ones in hardness. Both specimens exhibited no differences in their electrochemical corrosion properties in the artificial saliva through potentiodynamic curves and EIS, and no significant difference via XPS. Therefore, we concluded that within the scope of this study, SLM-fabricated restorations revealed good surface properties, such as proper hardness, homogeneous microstructure, and also showed sufficient corrosion resistance which could meet the needs of dental clinics.

  4. Evaluation of mechanical properties in metal wire mesh supported selective catalytic reduction (SCR) catalyst structures

    Science.gov (United States)

    Rajath, S.; Siddaraju, C.; Nandakishora, Y.; Roy, Sukumar

    2018-04-01

    The objective of this research is to evaluate certain specific mechanical properties of certain stainless steel wire mesh supported Selective catalytic reduction catalysts structures wherein the physical properties of the metal wire mesh and also its surface treatments played vital role thereby influencing the mechanical properties. As the adhesion between the stainless steel wire mesh and the catalyst material determines the bond strength and the erosion resistance of catalyst structures, surface modifications of the metal- wire mesh structure in order to facilitate the interface bonding is therefore very important to realize enhanced level of mechanical properties. One way to enhance such adhesion properties, the stainless steel wire mesh is treated with the various acids, i.e., chromic acid, phosphoric acid including certain mineral acids and combination of all those in various molar ratios that could generate surface active groups on metal surface that promotes good interface structure between the metal- wire mesh and metal oxide-based catalyst material and then the stainless steel wire mesh is dipped in the glass powder slurry containing some amount of organic binder. As a result of which the said catalyst material adheres to the metal-wire mesh surface more effectively that improves the erosion profile of supported catalysts structure including bond strength.

  5. Effect of catchment properties and flood generation regime on copula selection for bivariate flood frequency analysis

    Science.gov (United States)

    Filipova, Valeriya; Lawrence, Deborah; Klempe, Harald

    2018-02-01

    Applying copula-based bivariate flood frequency analysis is advantageous because the results provide information on both the flood peak and volume. More data are, however, required for such an analysis, and it is often the case that only data series with a limited record length are available. To overcome this issue of limited record length, data regarding climatic and geomorphological properties can be used to complement statistical methods. In this paper, we present a study of 27 catchments located throughout Norway, in which we assess whether catchment properties, flood generation processes and flood regime have an effect on the correlation between flood peak and volume and, in turn, on the selection of copulas. To achieve this, the annual maximum flood events were first classified into events generated primarily by rainfall, snowmelt or a combination of these. The catchments were then classified into flood regime, depending on the predominant flood generation process producing the annual maximum flood events. A contingency table and Fisher's exact test were used to determine the factors that affect the selection of copulas in the study area. The results show that the two-parameter copulas BB1 and BB7 are more commonly selected in catchments with high steepness, high mean annual runoff and rainfall flood regime. These findings suggest that in these types of catchments, the dependence structure between flood peak and volume is more complex and cannot be modeled effectively using a one-parameter copula. The results illustrate that by relating copula types to flood regime and catchment properties, additional information can be supplied for selecting copulas in catchments with limited data.

  6. The Effect of Mineral Powders Derived From Industrial Wastes on Selected Mechanical Properties of Concrete

    Science.gov (United States)

    Galińska, Anna; Czarnecki, Sławomir

    2017-10-01

    In recent years, concrete has been the most popular construction material. The main component of the concrete is cement. However, its production and transport causes significant emissions of CO2. Reports in the literature show that many laboratories are attempting to modify the composition of the concrete using various additives. These attempts are primarily designed to eliminate parts of cement. The greater part of the cement will be replaced with the selected additive, the more significant is the economic and ecological effect. Most attempts are related to the replacement of the selected additive in an amount of from 10 to 30% by weight of cement. Mineral powders, which are waste material producing crushed aggregate, are increasingly used for this purpose. Management of the waste carries significant cost related to their storage and disposal. With this in mind, the aim of this study was to evaluate the effect of mineral powders derived from industrial wastes on selected mechanical properties of concrete. In particular, the aim was to determine the effect of quartz and quartz-feldspar powders. For this purpose, 40, 50, 60% by weight of the cement was replaced by the selected powders. The results obtained were analysed and compared with previous attempts to replace the selected additive in an amount of from 10 to 30% by weight of cement.

  7. The Effect of Irradiation on Mechanical and Thermal Properties of Selected Types of Polymers

    Directory of Open Access Journals (Sweden)

    David Manas

    2018-02-01

    Full Text Available This article deals with the influence of electron-beam radiation on the micro-mechanical, thermo-mechanical, and structural properties of selected polymers. In the search for the desired improvement of polymers, it is possible to use, inter alia, one particular possible modification—Namely, crosslinking—Which is a process during which macromolecular chains start to connect to each other and, thus, create the spatial network in the structure. In the course of the treatment of the ionizing radiation, two actions can occur: crosslinking and scission of macromolecules, or degradation. Both these processes run in parallel. Using the crosslinking technology, standard and technical polymers can acquire the more “expensive” high-tech polymeric material properties and, thus, replace these materials in many applications. The polymers that were tested were selected from across the whole spectra of thermoplastics, ranging from commodity polymers, technical polymers, as well as high-performance polymers. These polymers were irradiated by different doses of beta radiation (33, 66, 99, 132, 165, and 198 kGy. The micro-mechanical and thermo-mechanical properties of these polymers were measured. When considering the results, it is obvious that irradiation acts on each polymer differently but, always when the optimal dose was found, the mechanical properties increased by up to 36%. The changes of micro-mechanical and thermo-mechanical properties were confirmed by structural measurement when the change of the micro-hardness and modulus corresponded to the crystalline phase change as determined by X-ray and gel content.

  8. Antioxidant and chemical properties of essential oil extracted from blend of selected spices

    Directory of Open Access Journals (Sweden)

    Ochuko Lucky Erukainure

    2015-07-01

    Full Text Available Objective: To investigate the chemical properties of essential oil extracted from blends of selected Nigerian spices as well as its antioxidant protective potentials against free radical in vitro. Methods: Essential oil was extracted from selected spices blend consisting of Monodora myristica, Myristica fragrans, Tetrapleura tetraptera, and Aframomum sceptrum using a Clevenger type apparatus. Oil obtained was subjected to phytochemical and gas chromatography-mass spectrometer analysis as well as analyzed for antioxidant activity which covers for 1,1-diphenyl-2 picrylhydrazyl, nitric oxide scavenging activities and reducing property. Results: Gas chromatography-mass spectrometer analysis revealed over 50 compoundfs with α-phellandrene being the most predominant compound (27.32%, which was followed by (--β-bourbonene (15.78% and 5-(1-methylethyl-α-phellandrene (11.80%. Phytochemical analysis showed high flavonoid content and a lower phenolic content. The oil showed a dose like dependent effect on the1-diphenyl-2 picrylhydrazyl and nitric oxide scavenging activities, these activities increased with increasing concentration. The same was also observed for the reducing power properties of the oil. Conclusions: The antioxidant activities exhibited by the essential oil in vitro signify its protective potential against free radicals. The chemical constituents, α-phellandrene in particular and the studied phytochemicals may be responsible for these effects. However, in vivo study is needed to further authenticate this potency.

  9. Anti-trypanosomal activities and structural chemical properties of selected compound classes.

    Science.gov (United States)

    Ponte-Sucre, Alicia; Bruhn, Heike; Schirmeister, Tanja; Cecil, Alexander; Albert, Christian R; Buechold, Christian; Tischer, Maximilian; Schlesinger, Susanne; Goebel, Tim; Fuß, Antje; Mathein, Daniela; Merget, Benjamin; Sotriffer, Christoph A; Stich, August; Krohne, Georg; Engstler, Markus; Bringmann, Gerhard; Holzgrabe, Ulrike

    2015-02-01

    Potent compounds do not necessarily make the best drugs in the market. Consequently, with the aim to describe tools that may be fundamental for refining the screening of candidates for animal and preclinical studies and further development, molecules of different structural classes synthesized within the frame of a broad screening platform were evaluated for their trypanocidal activities, cytotoxicities against murine macrophages J774.1 and selectivity indices, as well as for their ligand efficiencies and structural chemical properties. To advance into their modes of action, we also describe the morphological and ultrastructural changes exerted by selected members of each compound class on the parasite Trypanosoma brucei. Our data suggest that the potential organelles targeted are either the flagellar pocket (compound 77, N-Arylpyridinium salt; 15, amino acid derivative with piperazine moieties), the endoplasmic reticulum membrane systems (37, bisquaternary bisnaphthalimide; 77, N-Arylpyridinium salt; 68, piperidine derivative), or mitochondria and kinetoplasts (88, N-Arylpyridinium salt; 68, piperidine derivative). Amino acid derivatives with fumaric acid and piperazine moieties (4, 15) weakly inhibiting cysteine proteases seem to preferentially target acidic compartments. Our results suggest that ligand efficiency indices may be helpful to learn about the relationship between potency and chemical characteristics of the compounds. Interestingly, the correlations found between the physico-chemical parameters of the selected compounds and those of commercial molecules that target specific organelles indicate that our rationale might be helpful to drive compound design toward high activities and acceptable pharmacokinetic properties for all compound families.

  10. Lithium adsorptive properties of a new selective adsorbent derived from Li1.33Mn1.67O4

    International Nuclear Information System (INIS)

    Miyai, Yoshitaka; Ooi, Kenta; Nishimura, Tomonobu; Kumamoto, Jyunji.

    1994-01-01

    A new selective adsorbent was prepared by the acid treatment of Li 1.33 Mn 1.67 O 4 with spinel structure, followed by granulation with PVC as a binder. The adsorbent showed the highest capacities for lithium from seawater ; the equilibrium lithium uptakes reached 25.5 mg·g -1 by the powdered adsorbent and 18 mg·g -1 by the granulated one at 25degC. The column adsorption study with the granulated adsorbent (diameter 0.7-1.4mm) showed that the lithium uptake reached about 14 mg·g -1 by passing seawater for 30 days. This lithium content is nearly equal to that of lithium ore. Although the lithium adsorption capacity of the granulated adsorbent decreased slightly by repeating the adsorption-desorption cycle, it kept a high capacity as well as a high strength abrasion during the repetition of 10 cycles. (author)

  11. Effect of Build Angle on Surface Properties of Nickel Superalloys Processed by Selective Laser Melting

    Science.gov (United States)

    Covarrubias, Ernesto E.; Eshraghi, Mohsen

    2018-03-01

    Aerospace, automotive, and medical industries use selective laser melting (SLM) to produce complex parts through solidifying successive layers of powder. This additive manufacturing technique has many advantages, but one of the biggest challenges facing this process is the resulting surface quality of the as-built parts. The purpose of this research was to study the surface properties of Inconel 718 alloys fabricated by SLM. The effect of build angle on the surface properties of as-built parts was investigated. Two sets of sample geometries including cube and rectangular artifacts were considered in the study. It was found that, for angles between 15° and 75°, theoretical calculations based on the "stair-step" effect were consistent with the experimental results. Downskin surfaces showed higher average roughness values compared to the upskin surfaces. No significant difference was found between the average roughness values measured from cube and rectangular test artifacts.

  12. Magnetic refrigeration cycle analysis using selected thermodynamic property characterizations for gadolinium gallium garnet

    International Nuclear Information System (INIS)

    Murphy, R.W.

    1992-01-01

    Magneto-thermodynamic property characterizations were selected, adapted, and compared to material property data for gadolinium gallium garnet in the temperature range 4--40 K and magnetic field range 0--6 T. The most appropriate formulations were incorporated into a model in which methods similar to those previously developed for other materials and temperature ranges were used to make limitation and relative performance assessments of Carnot, ideal regenerative, and pseudo-constant field regenerative cycles. Analysis showed that although Carnot cycle limitations on available temperature lift for gadolinium gallium garnet are not as severe as those for materials previously examined, substantial improvements in cooling capacity/temperature lift combinations can be achieved using regenerative cycles within specified fields limits if significant loss mechanisms are mitigated

  13. Structural properties of H13 tool steel parts produced with use of selective laser melting technology

    International Nuclear Information System (INIS)

    Šafka, J; Ackermann, M; Voleský, L

    2016-01-01

    This paper deals with establishing of building parameters for 1.2344 (H13) tool steel processed using Selective Laser Melting (SLM) technology with layer thickness of 50 µm. In the first part of the work, testing matrix of models in the form of a cube with chamfered edge were built under various building parameters such as laser scanning speed and laser power. Resulting models were subjected to set of tests including measurement of surface roughness, inspection of inner structure with aid of Light Optical Microscopy and Scanning Electron Microscopy and evaluation of micro-hardness. These tests helped us to evaluate an influence of changes in building strategy to the properties of the resulting model. In the second part of the work, mechanical properties of the H13 steel were examined. For this purpose, the set of samples in the form of “dog bone” were printed under three different alignments towards the building plate and tested on universal testing machine. Mechanical testing of the samples should then reveal if the different orientation and thus different layering of the material somehow influence its mechanical properties. For this type of material, the producer provides the parameters for layer thickness of 30 µm only. Thus, our 50 µm building strategy brings shortening of the building time which is valuable especially for large models. Results of mechanical tests show slight variation in mechanical properties for various alignment of the sample. (paper)

  14. Structural properties of H13 tool steel parts produced with use of selective laser melting technology

    Science.gov (United States)

    Šafka, J.; Ackermann, M.; Voleský, L.

    2016-04-01

    This paper deals with establishing of building parameters for 1.2344 (H13) tool steel processed using Selective Laser Melting (SLM) technology with layer thickness of 50 µm. In the first part of the work, testing matrix of models in the form of a cube with chamfered edge were built under various building parameters such as laser scanning speed and laser power. Resulting models were subjected to set of tests including measurement of surface roughness, inspection of inner structure with aid of Light Optical Microscopy and Scanning Electron Microscopy and evaluation of micro-hardness. These tests helped us to evaluate an influence of changes in building strategy to the properties of the resulting model. In the second part of the work, mechanical properties of the H13 steel were examined. For this purpose, the set of samples in the form of “dog bone” were printed under three different alignments towards the building plate and tested on universal testing machine. Mechanical testing of the samples should then reveal if the different orientation and thus different layering of the material somehow influence its mechanical properties. For this type of material, the producer provides the parameters for layer thickness of 30 µm only. Thus, our 50 µm building strategy brings shortening of the building time which is valuable especially for large models. Results of mechanical tests show slight variation in mechanical properties for various alignment of the sample.

  15. Mechanical Properties of Optimized Diamond Lattice Structure for Bone Scaffolds Fabricated via Selective Laser Melting

    Science.gov (United States)

    Zhang, David Z.; Zhang, Peng; Zhao, Miao; Jafar, Salman

    2018-01-01

    Developments in selective laser melting (SLM) have enabled the fabrication of periodic cellular lattice structures characterized by suitable properties matching the bone tissue well and by fluid permeability from interconnected structures. These multifunctional performances are significantly affected by cell topology and constitutive properties of applied materials. In this respect, a diamond unit cell was designed in particular volume fractions corresponding to the host bone tissue and optimized with a smooth surface at nodes leading to fewer stress concentrations. There were 33 porous titanium samples with different volume fractions, from 1.28 to 18.6%, manufactured using SLM. All of them were performed under compressive load to determine the deformation and failure mechanisms, accompanied by an in-situ approach using digital image correlation (DIC) to reveal stress–strain evolution. The results showed that lattice structures manufactured by SLM exhibited comparable properties to those of trabecular bone, avoiding the effects of stress-shielding and increasing longevity of implants. The curvature of optimized surface can play a role in regulating the relationship between density and mechanical properties. Owing to the release of stress concentration from optimized surface, the failure mechanism of porous titanium has been changed from the pattern of bottom-up collapse by layer (or cell row) to that of the diagonal (45°) shear band, resulting in the significant enhancement of the structural strength. PMID:29510492

  16. Mechanical Properties of Optimized Diamond Lattice Structure for Bone Scaffolds Fabricated via Selective Laser Melting.

    Science.gov (United States)

    Liu, Fei; Zhang, David Z; Zhang, Peng; Zhao, Miao; Jafar, Salman

    2018-03-03

    Developments in selective laser melting (SLM) have enabled the fabrication of periodic cellular lattice structures characterized by suitable properties matching the bone tissue well and by fluid permeability from interconnected structures. These multifunctional performances are significantly affected by cell topology and constitutive properties of applied materials. In this respect, a diamond unit cell was designed in particular volume fractions corresponding to the host bone tissue and optimized with a smooth surface at nodes leading to fewer stress concentrations. There were 33 porous titanium samples with different volume fractions, from 1.28 to 18.6%, manufactured using SLM. All of them were performed under compressive load to determine the deformation and failure mechanisms, accompanied by an in-situ approach using digital image correlation (DIC) to reveal stress-strain evolution. The results showed that lattice structures manufactured by SLM exhibited comparable properties to those of trabecular bone, avoiding the effects of stress-shielding and increasing longevity of implants. The curvature of optimized surface can play a role in regulating the relationship between density and mechanical properties. Owing to the release of stress concentration from optimized surface, the failure mechanism of porous titanium has been changed from the pattern of bottom-up collapse by layer (or cell row) to that of the diagonal (45°) shear band, resulting in the significant enhancement of the structural strength.

  17. Effect of material selection and background impurity on interface property and resulted CIP-GMR performance

    International Nuclear Information System (INIS)

    Peng Xilin; Morrone, Augusto; Nikolaev, Konstantin; Kief, Mark; Ostrowski, Mark

    2009-01-01

    In this paper, we investigated the effect of background base pressure, wafer-transferring time between process modules, and stack layer material selection on the current-in-plane giant magneto-resistive (CIP-GMR) interface properties and the resulted CIP-GMR performance. Experimental results showed that seed layer/AFM interface, AFM/pinned layer (PL) interface, pinned layer/Ru interface, and reference layer (RL)/Cu spacer interface are among the most critical ones for a CIP-GMR device. By reducing the background impurity level (water moisture and oxygen), optimizing the wafer process flow sequence, and careful stack-layer material selection, such critical interfaces in a CIP-GMR device can be preserved. Consequently, a much robust GMR performance control can be achieved.

  18. Microstructure and mechanical properties of a novel β titanium metallic composite by selective laser melting

    International Nuclear Information System (INIS)

    Vrancken, B.; Thijs, L.; Kruth, J.-P.; Van Humbeeck, J.

    2014-01-01

    Selective laser melting (SLM) is an additive manufacturing process in which functional, complex parts are produced by selectively melting consecutive layers of powder with a laser beam. This flexibility enables the exploration of a wide spectrum of possibilities in creating novel alloys or even metal–metal composites with unique microstructures. In this research, Ti6Al4V-ELI powder was mixed with 10 wt.% Mo powder. In contrast to the fully α′ microstructure of Ti6Al4V after SLM, the novel microstructure consists of a β titanium matrix with randomly dispersed pure Mo particles, as observed by light optical microscopy, scanning electron microscopy and X-ray diffraction. Most importantly, the solidification mechanism changes from planar to cellular mode. Microstructures after heat treatment indicate that the β phase is metastable and locate the β transus at ∼900 °C, and tensile properties are equal to or better than conventional β titanium alloys

  19. Characterization of sorption properties of selected soils from Lublin region by using water vapour adsorption method

    Science.gov (United States)

    Skic, Kamil; Boguta, Patrycja; Sokołowska, Zofia

    2016-04-01

    *The studies were carried out within the framework of a research project. The project was financed from funds of National Science Center on the base of decision number DEC-2013/11/D/NZ9/02545 Among many methods proposed to study sorption properties of soils an analysis of adsorption/ desorption isotherm is probably the easiest and most convenient one. It characterizes both quantity and quality of mineral and organic components and also their physical and physicochemical properties. The main aim of this study is comparison of sorption properties of selected Polish soils by using water vapour adsorption method. Samples were taken from the depth of 0-20 cm, from the Lublin region, eastern Poland. Soils were selected on the basis of their different physicochemical properties and were classified as: Haplic Fluvisol, Haplic Chernozem, Mollic Gleysol, Rendzic Phaeozem, Stagnic Luvisol, Haplic Cambisol (WG WRB 2006). Data taken from experimental adsorption isotherms were used to determine parameters of monolayer capacity, specific surface area and the total amount of vapour adsorbed at relative pressure of 0.974. Obtained adsorption and desorption isotherms reviled that adsorbate molecules interacted with the soil particles in different extent. Similar monolayer capacity was observed for Haplic Fluvisol, Haplic Chernozem and Stagnic Luvisol, while for Mollic Gleysol was more than 4 times higher. Mollic Gleysol was also characterized by highest values of specific surface area as well as quantity of adsorbed vapour at relative pressure of 0.974. Higher sorption was caused by presence of soil colloids which contains functional groups of a polar nature (mainly hydroxyls, phenolic and carboxyls). These groups similarly to silicates, oxides, hydratable cations as well as electric charge form adsorption centres for water vapour molecules.

  20. Microalgal Species Selection for Biodiesel Production Based on Fuel Properties Derived from Fatty Acid Profiles

    Directory of Open Access Journals (Sweden)

    Md. Nurun Nabi

    2013-10-01

    Full Text Available Physical and chemical properties of biodiesel are influenced by structural features of the fatty acids, such as chain length, degree of unsaturation and branching of the carbon chain. This study investigated if microalgal fatty acid profiles are suitable for biodiesel characterization and species selection through Preference Ranking Organisation Method for Enrichment Evaluation (PROMETHEE and Graphical Analysis for Interactive Assistance (GAIA analysis. Fatty acid methyl ester (FAME profiles were used to calculate the likely key chemical and physical properties of the biodiesel [cetane number (CN, iodine value (IV, cold filter plugging point, density, kinematic viscosity, higher heating value] of nine microalgal species (this study and twelve species from the literature, selected for their suitability for cultivation in subtropical climates. An equal-parameter weighted (PROMETHEE-GAIA ranked Nannochloropsis oculata, Extubocellulus sp. and Biddulphia sp. highest; the only species meeting the EN14214 and ASTM D6751-02 biodiesel standards, except for the double bond limit in the EN14214. Chlorella vulgaris outranked N. oculata when the twelve microalgae were included. Culture growth phase (stationary and, to a lesser extent, nutrient provision affected CN and IV values of N. oculata due to lower eicosapentaenoic acid (EPA contents. Application of a polyunsaturated fatty acid (PUFA weighting to saturation led to a lower ranking of species exceeding the double bond EN14214 thresholds. In summary, CN, IV, C18:3 and double bond limits were the strongest drivers in equal biodiesel parameter-weighted PROMETHEE analysis.

  1. Ti-6Al-4V Additively Manufactured by Selective Laser Melting with Superior Mechanical Properties

    Science.gov (United States)

    Xu, W.; Sun, S.; Elambasseril, J.; Liu, Q.; Brandt, M.; Qian, M.

    2015-03-01

    The Achilles' heel of additively manufactured Ti-6Al-4V by selective laser melting (SLM) is its inferior mechanical properties compared with its wrought (forged) counterparts. Acicular α' martensite resulted from rapid cooling by SLM is primarily responsible for high strength but inadequate tensile ductility achieved in the as-fabricated state. This study presents a solution to eliminating the adverse effect of the nonequilibrium α' martensite. This is achieved by enabling in situ martensite decomposition into a novel ultrafine (200-300 nm) lamellar ( α + β) microstructure via the selection of an array of processing variables including the layer thickness, energy density, and focal offset distance. The resulting tensile elongation reached 11.4% while the yield strength was kept above 1100 MPa. These properties compare favorably with those of mill-annealed Ti-6Al-4V consisting of globular α and β. The fatigue life of SLM-fabricated Ti-6Al-4V with an ultrafine lamellar ( α + β) structure has approached that of the mill-annealed counterparts and is much superior to that of SLM-fabricated Ti-6Al-4V with α' martensite.

  2. Architectural properties of the neuromuscular compartments in selected forearm skeletal muscles.

    Science.gov (United States)

    Liu, An-Tang; Liu, Ben-Li; Lu, Li-Xuan; Chen, Gang; Yu, Da-Zhi; Zhu, Lie; Guo, Rong; Dang, Rui-Shan; Jiang, Hua

    2014-07-01

    The purposes f this study were to (i) explore the possibility of splitting the selected forearm muscles into separate compartments in human subjects; (ii) quantify the architectural properties of each neuromuscular compartment; and (iii) discuss the implication of these properties in split tendon transfer procedures. Twenty upper limbs from 10 fresh human cadavers were used in this study. Ten limbs of five cadavers were used for intramuscular nerve study by modified Sihler's staining technique, which confirmed the neuromuscular compartments. The other 10 limbs were included for architectural analysis of neuromuscular compartments. The architectural features of the compartments including muscle weight, muscle length, fiber length, pennation angle, and sarcomere length were determined. Physiological cross-sectional area and fiber length/muscle length ratio were calculated. Five of the selected forearm muscles were ideal candidates for splitting, including flexor carpi ulnaris, flexor carpi radials, extensor carpi radialis brevis, extensor carpi ulnaris and pronator teres. The humeral head of pronator teres contained the longest fiber length (6.23 ± 0.31 cm), and the radial compartment of extensor carpi ulnaris contained the shortest (2.90 ± 0.28 cm). The ulnar compartment of flexor carpi ulnaris had the largest physiological cross-sectional area (5.17 ± 0.59 cm(2)), and the ulnar head of pronator teres had the smallest (0.67 ± 0.06 cm(2)). Fiber length/muscle length ratios of the neuromuscular compartments were relatively low (average 0.27 ± 0.09, range 0.18-0.39) except for the ulnar head of pronator teres, which had the highest one (0.72 ± 0.05). Using modified Sihler's technique, this research demonstrated that each compartment of these selected forearm muscles has its own neurovascular supply after being split along its central tendon. Data of the architectural properties of each neuromuscular compartment provide insight into the 'design' of their

  3. Architectural properties of the neuromuscular compartments in selected forearm skeletal muscles

    Science.gov (United States)

    Liu, An-Tang; Liu, Ben-Li; Lu, Li-Xuan; Chen, Gang; Yu, Da-Zhi; Zhu, Lie; Guo, Rong; Dang, Rui-Shan; Jiang, Hua

    2014-01-01

    The purposes f this study were to (i) explore the possibility of splitting the selected forearm muscles into separate compartments in human subjects; (ii) quantify the architectural properties of each neuromuscular compartment; and (iii) discuss the implication of these properties in split tendon transfer procedures. Twenty upper limbs from 10 fresh human cadavers were used in this study. Ten limbs of five cadavers were used for intramuscular nerve study by modified Sihler's staining technique, which confirmed the neuromuscular compartments. The other 10 limbs were included for architectural analysis of neuromuscular compartments. The architectural features of the compartments including muscle weight, muscle length, fiber length, pennation angle, and sarcomere length were determined. Physiological cross-sectional area and fiber length/muscle length ratio were calculated. Five of the selected forearm muscles were ideal candidates for splitting, including flexor carpi ulnaris, flexor carpi radials, extensor carpi radialis brevis, extensor carpi ulnaris and pronator teres. The humeral head of pronator teres contained the longest fiber length (6.23 ± 0.31 cm), and the radial compartment of extensor carpi ulnaris contained the shortest (2.90 ± 0.28 cm). The ulnar compartment of flexor carpi ulnaris had the largest physiological cross-sectional area (5.17 ± 0.59 cm2), and the ulnar head of pronator teres had the smallest (0.67 ± 0.06 cm2). Fiber length/muscle length ratios of the neuromuscular compartments were relatively low (average 0.27 ± 0.09, range 0.18–0.39) except for the ulnar head of pronator teres, which had the highest one (0.72 ± 0.05). Using modified Sihler's technique, this research demonstrated that each compartment of these selected forearm muscles has its own neurovascular supply after being split along its central tendon. Data of the architectural properties of each neuromuscular compartment provide insight into the ‘design’ of their

  4. Microstructure and mechanical properties of stainless steel/calcium silicate composites manufactured by selective laser melting

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Zeng [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China); Shanghai Key Lab. of D& A for Metal-Functional Materials, Shanghai 201804 (China); Wang, Lianfeng [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China); Shanghai Aerospace Equipments Manufacturer, Shanghai 200240 (China); Jia, Min [Shanghai Aircraft Manufacturing Co., Ltd, Shanghai 200436 (China); Cheng, Lingyu [Shanghai Aerospace Equipments Manufacturer, Shanghai 200240 (China); Yan, Biao, E-mail: 84016@tongji.edu.cn [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China); Shanghai Key Lab. of D& A for Metal-Functional Materials, Shanghai 201804 (China)

    2017-02-01

    Selective laser melting (SLM) is raised as one kind of additive manufacturing (AM) which is based on the discrete-stacking concept. This technique can fabricate advanced composites with desirable properties directly from 3D CAD data. In this research, 316L stainless steel (316L SS) and different fractions of calcium silicate (CaSiO{sub 3}) composites (weight fractions of calcium silicate are 0%, 5%,10% and 15%, respectively) were prepared by SLM technique with a purpose to develop biomedical metallic materials. The relative density, tensile, microhardness and elastic modulus of the composites were tested, their microstructures and fracture morphologies were observed using optical microscope (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). It was found that the addition of CaSiO{sub 3} particles influenced the microstructure and mechanical properties of specimens significantly. The CaSiO{sub 3} precipitates from the overlap of adjacent tracks and became the origin of the defects. The tensile strength of specimens range 320–722 MPa. The microhardness and elastic modulus are around 250 HV and 215 GPa respectively. These composites were ductile materials and the fracture mode of the composites was mixed mode of ductile and brittle fracture. The 316L SS/CaSiO{sub 3} composites can be a potential biomedical metallic materials in the medical field. - Highlights: • 316L SS/CaSiO{sub 3} composites were fabricated by selective laser melting. • Microstructure, mechanical properties, corrosion resistance of samples was studied. • Composites is a ductile material and mixed mode of ductile and brittle fracture. • Composites is a potential biomedical metallic materials in the medical field.

  5. The necessity of microscopy to characterize the optical properties of size-selected, nonspherical aerosol particles.

    Science.gov (United States)

    Veghte, Daniel P; Freedman, Miriam A

    2012-11-06

    It is currently unknown whether mineral dust causes a net warming or cooling effect on the climate system. This uncertainty stems from the varied and evolving shape and composition of mineral dust, which leads to diverse interactions of dust with solar and terrestrial radiation. To investigate these interactions, we have used a cavity ring-down spectrometer to study the optical properties of size-selected calcium carbonate particles, a reactive component of mineral dust. The size selection of nonspherical particles like mineral dust can differ from spherical particles in the polydispersity of the population selected. To calculate the expected extinction cross sections, we use Mie scattering theory for monodisperse spherical particles and for spherical particles with the polydispersity observed in transmission electron microscopy images. Our results for calcium carbonate are compared to the well-studied system of ammonium sulfate. While ammonium sulfate extinction cross sections agree with Mie scattering theory for monodisperse spherical particles, the results for calcium carbonate deviate at large and small particle sizes. We find good agreement for both systems, however, between the calculations performed using the particle images and the cavity ring-down data, indicating that both ammonium sulfate and calcium carbonate can be treated as polydisperse spherical particles. Our results indicate that having an independent measure of polydispersity is essential for understanding the optical properties of nonspherical particles measured with cavity ring-down spectroscopy. Our combined spectroscopy and microscopy techniques demonstrate a novel method by which cavity ring-down spectroscopy can be extended for the study of more complex aerosol particles.

  6. Physical and water properties of selected Polish heavy soils of various origins

    Directory of Open Access Journals (Sweden)

    Kaczmarek Zbigniew

    2015-12-01

    Full Text Available The paper presents the characteristics of selected physical, chemical, and water properties of four mineral arable soils characterized with heavy and very heavy texture. Soil samples from genetic horizons of black earths from areas near Kętrzyn, Gniew and Kujawy, and alluvial soils from Żuławy were used. The following properties were determined in the samples of undisturbed and disturbed structure: texture, particle density, bulk density, porosity, natural and hygroscopic moistures, maximal hygroscopic capacity, saturated hydraulic conductivity, potential of water bonding in soil, total and readily available water, total retention in the horizon of 0–50 cm, drainage porosity, content of organic carbon and total nitrogen Parent rocks of these soils were clays, silts and loams of various origin. High content of clay fraction strongly influenced the values of all the analyzed properties. All the examined soils had high content of organic carbon and total nitrogen and reaction close to neutral or alkaline. High content of mineral and organic colloids and, what follows, beneficial state of top horizons’ structure, determined – apart from heavy texture – low soil bulk density and high porosity. The investigated soils were characterized by high field water capacity and wide scopes of total and readily available water. The saturated hydraulic conductivity was low and characteristic to heavy mineral arable soils. The parameter which influenced the variability of analyzed parameters most was texture.

  7. Selected Rheological Properties of RS3/4 Type Resistant Starch

    Directory of Open Access Journals (Sweden)

    Kapelko-Żeberska Małgorzata

    2017-12-01

    Full Text Available This study was aimed at determining the effect of acetylation degree and crosslinking of retrograded starch with adipic acid on selected rheological properties of prepared pastes and gels. The esterification of retrograded starch allowed obtaining preparations with various degrees of substitution with residues of acetic (0.7–11.2 g/100 g and adipic acids (0.1–0.3 g/100 g. Acetylation and crosslinking caused a decrease in amylose content of the preparations (3–21 g/100 g. Solubility of the preparations in water, in a wide range of variability, was increasing along with an increasing degree of acetylation and with a decreasing degree of crosslinking (19–100 g/100 g. Values of most of the rheological coefficients determined based on the flow curves of the prepared pastes and mechanical spectra of gels (3.5properties upon the effect of double modification were not the sum of changes proceeding as a result of single modifications. Instead, interaction of both factors was observed. The conducted modifications enable modelling the properties of produced preparations.

  8. Investigation of the selected properties of dusts from the reclamation of spent sands with bentonite

    Directory of Open Access Journals (Sweden)

    J. Kamińska

    2011-10-01

    Full Text Available The investigation results of the selected properties of dusts generated during the mechanical reclamation of spent sands with bentonite as well as dusts from the dedusting system of sand processing plant are presented in the hereby paper. Investigations were performed with regard to determination conditions allowing to pelletise dusts in the bowl granulator. The verified methods of testing physical and chemical dust properties such as: specific density, bulk density of loosely put materials and apparent density of compacted materials together with their corresponding porosity, ignition losses and pH values, were applied. Granular composition of dusts generated during abrasion of spent binding materials in mechanical dry reclamation processes of spent sands with bentonite and coal dusts were performed by the laser diffraction analysis, allowing to broaden the measuring range of particle diameters. The optimal wetting agent content (in this case water at which the dust-water mixture obtains the best strength properties – after compacting by means of the standard moulder’s rammer – was determined.

  9. Uptake of skilled attendance along the continuum of care in rural Western Kenya: selected analysis from Global Health initiative survey-2012.

    Science.gov (United States)

    Mwangi, Winfred; Gachuno, Onesmus; Desai, Meghna; Obor, David; Were, Vincent; Odhiambo, Frank; Nyaguara, Amek; Laserson, Kayla F

    2018-05-16

    attendance, 34% reported ANC, HF delivery and PNC attendance and only 18% reported ANC, HF delivery, PNC and NBA attendance. Uptake of services drastically declined from antenatal to postnatal period, along the continuum of care. Age and education were key determinants of uptake.

  10. Selection of autochthonous Oenococcus oeni strains according to their oenological properties and vinification results.

    Science.gov (United States)

    Ruiz, Patricia; Izquierdo, Pedro Miguel; Seseña, Susana; Palop, María Llanos

    2010-02-28

    The goal of this study is to carry out a characterization of 84 Oenococcus oeni strains isolated from Tempranillo wine samples taken at the cellars in Castilla-La Mancha, in order to select those showing the highest potential as oenological starter cultures. Various oenological properties were analyzed and the ability of some of these strains to grow and undergo MLF in simulated laboratory microvinifications was tested. Twenty-two strains were selected on the basis of fermentation assays and the eight that produced the best results in the chemical analysis of the wines were chosen for further assays. None of the eight strains was either able to produce biogenic amines or displayed tannase or anthocyanase activities. On the other hand all presented activity against p-NP-beta Glucopyranoside, p-NP-alpha Glucopyranoside and p-NP-beta xylopyranoside. Randomly Amplified Polymorphic DNA (RAPD)-PCR was used to determine the colonizing ability of the inoculated strains. C22L9 and D13L13 strains showed the highest implantation values. On the basis of this characterization, two strains have been selected which are suitable as starter cultures for MLF of Tempranillo wine. Use of these strains will ensure that MLF proceeds successfully and gives retention of the organoleptic characteristics of wines made in Castilla-La Mancha. (c) 2009 Elsevier B.V. All rights reserved.

  11. Photocatalytic properties and selective antimicrobial activity of TiO2(Eu)/CuO nanocomposite

    Science.gov (United States)

    Michal, Robert; Dworniczek, Ewa; Caplovicova, Maria; Monfort, Olivier; Lianos, Panagiotis; Caplovic, Lubomir; Plesch, Gustav

    2016-05-01

    TiO2(Eu)/CuO nanocomposites were prepared by precipitation method. The anatase nanocrystallites with a size of 26 nm exhibited well crystallized and characteristical dipyramidal morphology and {1 0 1} and {0 0 1} faceting. Transmission electron microscopy photographs with atomic resolution showed that the Eu(III) dopants were bounded on surface of titania. In the composites, the CuO nanocrystals exhibiting a monoclinic tenorite structure with a size in the range from 2 to 5 nm were grafted to the surface of titania. The influence of copper(II) oxide led to distinct selectivity in the photocatalytic and antimicrobial properties of the investigated TiO2(Eu)/CuO nanocomposites. While the presence of CuO nanocrystals strongly increased the photocatalytic production of hydrogen by ethanol reforming, it decreased the activity in photoinduced total mineralization of phenol comparing with non-modified TiO2(Eu). In investigated TiO2(Eu)/CuO powders, the photoinduced antimicrobial activity against membranes of Enterococcus species was influenced by the selective binding of CuO to the surface of the microorganism leading to distinct selectivity in their action. The activity against Enterococcus faecalis was higher than against Enterococcus faecium.

  12. Adsorption Properties of MFM-400 and MFM-401 with CO2 and Hydrocarbons: Selectivity Derived from Directed Supramolecular Interactions.

    Science.gov (United States)

    Ibarra, Ilich A; Mace, Amber; Yang, Sihai; Sun, Junliang; Lee, Sukyung; Chang, Jong-San; Laaksonen, Aatto; Schröder, Martin; Zou, Xiaodong

    2016-08-01

    ([Sc2(OH)2(BPTC)]) (H4BPTC = biphenyl-3,3',5,5'-tetracarboxylic acid), MFM-400 (MFM = Manchester Framework Material, previously designated NOTT), and ([Sc(OH)(TDA)]) (H2TDA = thiophene-2,5-dicarboxylic acid), MFM-401, both show selective and reversible capture of CO2. In particular, MFM-400 exhibits a reasonably high CO2 uptake at low pressures and competitive CO2/N2 selectivity coupled to a moderate isosteric heat of adsorption (Qst) for CO2 (29.5 kJ mol(-1)) at zero coverage, thus affording a facile uptake-release process. Grand canonical Monte Carlo (GCMC) and density functional theory (DFT) computational analyses of CO2 uptake in both materials confirmed preferential adsorption sites consistent with the higher CO2 uptake observed experimentally for MFM-400 over MFM-401 at low pressures. For MFM-400, the Sc-OH group participates in moderate interactions with CO2 (Qst = 33.5 kJ mol(-1)), and these are complemented by weak hydrogen-bonding interactions (O···H-C = 3.10-3.22 Å) from four surrounding aromatic -CH groups. In the case of MFM-401, adsorption is provided by cooperative interactions of CO2 with the Sc-OH group and one C-H group. The binding energies obtained by DFT analysis for the adsorption sites for both materials correlate well with the observed moderate isosteric heats of adsorption for CO2. GCMC simulations for both materials confirmed higher uptake of EtOH compared with nonpolar vapors of toluene and cyclohexane. This is in good correlation with the experimental data, and DFT analysis confirmed the formation of a strong hydrogen bond between EtOH and the hydrogen atom of the hydroxyl group of the MFM-400 and MFM-401 framework (FW) with H-OEtOH···H-OFW distances of 1.77 and 1.75 Å, respectively. In addition, the accessible regeneration of MFM-400 and MFM-401 and release of CO2 potentially provide minimal economic and environmental penalties.

  13. Cell uptake survey of pegylated nanographene oxide.

    Science.gov (United States)

    Vila, M; Portolés, M T; Marques, P A A P; Feito, M J; Matesanz, M C; Ramírez-Santillán, C; Gonçalves, G; Cruz, S M A; Nieto, A; Vallet-Regi, M

    2012-11-23

    Graphene and more specifically, nanographene oxide (GO) has been proposed as a highly efficient antitumoral therapy agent. Nevertheless, its cell uptake kinetics, its influence in different types of cells and the possibility of controlling cellular internalization timing, is still a field that remains unexplored. Herein, different cell types have been cultured in vitro for several incubation periods in the presence of 0.075 mg ml(-1) pegylated GO solutions. GO uptake kinetics revealed differences in the agent's uptake amount and speed as a function of the type of cell involved. Osteoblast-like cells GO uptake is higher and faster without resulting in greater cell membrane damage. Moreover, the dependence on the commonly used PEG nature (number of branches) also influences the viability and cell uptake speed. These facts play an important role in the future definition of timing parameters and selective cell uptake control in order to achieve an effective therapy.

  14. Cell uptake survey of pegylated nanographene oxide

    International Nuclear Information System (INIS)

    Vila, M; Nieto, A; Vallet-Regi, M; Portolés, M T; Feito, M J; Matesanz, M C; Ramírez-Santillán, C; Marques, P A A P; Gonçalves, G; Cruz, S M A

    2012-01-01

    Graphene and more specifically, nanographene oxide (GO) has been proposed as a highly efficient antitumoral therapy agent. Nevertheless, its cell uptake kinetics, its influence in different types of cells and the possibility of controlling cellular internalization timing, is still a field that remains unexplored. Herein, different cell types have been cultured in vitro for several incubation periods in the presence of 0.075 mg ml −1 pegylated GO solutions. GO uptake kinetics revealed differences in the agent’s uptake amount and speed as a function of the type of cell involved. Osteoblast-like cells GO uptake is higher and faster without resulting in greater cell membrane damage. Moreover, the dependence on the commonly used PEG nature (number of branches) also influences the viability and cell uptake speed. These facts play an important role in the future definition of timing parameters and selective cell uptake control in order to achieve an effective therapy. (paper)

  15. Dose selection for radioiodine therapy of borderline hyperthyroid patients according to thyroid uptake of 99mTc-pertechnetate: applicability to unifocal thyroid autonomy?

    International Nuclear Information System (INIS)

    Reinhardt, Michael J.; Joe, Alexius Y.; Biermann, Kim; Brockmann, Holger; Mallek, Dirk von; Ezziddin, Samer; Wissmeyer, Michael; Juengling, Freimut D.; Krause, Thomas M.

    2006-01-01

    The aim of this study was to evaluate the feasibility of applying a previously described dose strategy based on 99m Tc-pertechnetate thyroid uptake under thyrotropin suppression (TcTU s ) to radioiodine therapy for unifocal thyroid autonomy. A total of 425 consecutive patients (302 females, 123 males; age 63.1±10.3 years) with unifocal thyroid autonomy were treated at three different centres with 131 I, using Marinelli's formula for calculation of three different absorbed dose schedules: 100-300 Gy to the total thyroid volume according to the pre-treatment TcTU s (n=146), 300 Gy to the nodule volume (n=137) and 400 Gy to the nodule volume (n=142). Successful elimination of functional thyroid autonomy with either euthyroidism or hypothyroidism occurred at a mean of 12 months after radioiodine therapy in 94.5% of patients receiving 100-300 Gy to the thyroid volume, in 89.8% of patients receiving 300 Gy to the nodule volume and in 94.4% receiving 400 Gy to the nodule volume. Reduction in thyroid volume was highest for the 100-300 Gy per thyroid and 400 Gy per nodule strategies (36±19% and 38±20%, respectively) and significantly lower for the 300 Gy per nodule strategy (28±16%; p s can be used independently of the scintigraphic pattern of functional autonomous tissue in the thyroid. (orig.)

  16. In vivo and in vitro studies on the potentiation of muscarinic receptor stimulation by alaproclate, a selective 5-HT uptake blocker

    International Nuclear Information System (INIS)

    Oegren, S.O.; Nordstroem, Oe.; Danielsson, E.; Peterson, L.-L.; Bartfai, T.

    1985-01-01

    Alaproclate (10-60 mg/kg) injected i.p. into male mice potentiated and prolonged the oxotremorine and physostigmine-induced tremor in a dosedependent manner. Atropine completely blocked the tremor caused by oxotremorine or physostigmine both in the presence and absence of alaproclate. Pretreatment with the 5-HT receptor antagonist metitepine completely blocked the enhancement of oxotremorine-induced tremor caused by alaproclate. Biochemical studies indicated that the above effects cannot be explained by assuming that alaproclate a) acts as a cholinergic agonist, b) inhibits the acetylcholine esterase, c) interferes with choline uptake or acetylcholine synthesis, or d) directly potentiates the release of acetylcholine. In ligand binding studies alaproclate was found to be a weak competitive inhibitor of muscarinic antagonist binding to membranes from the rat cerebral cortex, rat striatum, human cerebral cortex and human striatum. (Ksub(i) approximately 28-40 μM in all four tissues). The present results suggest that alaproclate may potentiate muscarinic responses by a mechanism involving serotonergic receptor mechanisms rather than by a direct interaction with the muscarinic cholinergic receptors. (Author)

  17. In vivo and in vitro studies on the potentiation of muscarinic receptor stimulation by alaproclate, a selective 5-HT uptake blocker

    Energy Technology Data Exchange (ETDEWEB)

    Oegren, S.O. (Astra Pharmaceuticals AB, Soedertaelje (Sweden)); Nordstroem, Oe.; Danielsson, E.; Peterson, L.L.; Bartfai, T.

    1985-01-01

    Alaproclate (10-60 mg/kg) injected i.p. into male mice potentiated and prolonged the oxotremorine and physostigmine-induced tremor in a dose dependent manner. Atropine completely blocked the tremor caused by oxotremorine or physostigmine both in the presence and absence of alaproclate. Pretreatment with the 5-HT receptor antagonist metitepine completely blocked the enhancement of oxotremorine-induced tremor caused by alaproclate. Biochemical studies indicated that the above effects cannot be explained by assuming that alaproclate a) acts as a cholinergic agonist, b) inhibits the acetylcholine esterase, c) interferes with choline uptake or acetylcholine synthesis, or d) directly potentiates the release of acetylcholine. In ligand binding studies alaproclate was found to be a weak competitive inhibitor of muscarinic antagonist binding to membranes from the rat cerebral cortex, rat striatum, human cerebral cortex and human striatum. (Ksub(i) approximately 28-40 ..mu..M in all four tissues). The present results suggest that alaproclate may potentiate muscarinic responses by a mechanism involving serotonergic receptor mechanisms rather than by a direct interaction with the muscarinic cholinergic receptors.

  18. Photocatalytic properties and selective antimicrobial activity of TiO2(Eu)/CuO nanocomposite

    International Nuclear Information System (INIS)

    Michal, Robert; Dworniczek, Ewa; Caplovicova, Maria; Monfort, Olivier; Lianos, Panagiotis; Caplovic, Lubomir; Plesch, Gustav

    2016-01-01

    Highlights: • Nanocomposites composed of Eu-doped anatase grafted with CuO. • Increase in photocatalytic hydrogen production due to CuO acting as electrons sink. • CuO in composites decreasing the photoinduced total mineralization of phenol. • Selective photoinduced antimicrobial activity against Enterococcus species. - Abstract: TiO 2 (Eu)/CuO nanocomposites were prepared by precipitation method. The anatase nanocrystallites with a size of 26 nm exhibited well crystallized and characteristical dipyramidal morphology and {1 0 1} and {0 0 1} faceting. Transmission electron microscopy photographs with atomic resolution showed that the Eu(III) dopants were bounded on surface of titania. In the composites, the CuO nanocrystals exhibiting a monoclinic tenorite structure with a size in the range from 2 to 5 nm were grafted to the surface of titania. The influence of copper(II) oxide led to distinct selectivity in the photocatalytic and antimicrobial properties of the investigated TiO 2 (Eu)/CuO nanocomposites. While the presence of CuO nanocrystals strongly increased the photocatalytic production of hydrogen by ethanol reforming, it decreased the activity in photoinduced total mineralization of phenol comparing with non-modified TiO 2 (Eu). In investigated TiO 2 (Eu)/CuO powders, the photoinduced antimicrobial activity against membranes of Enterococcus species was influenced by the selective binding of CuO to the surface of the microorganism leading to distinct selectivity in their action. The activity against Enterococcus faecalis was higher than against Enterococcus faecium.

  19. Dose selection for radioiodine therapy of borderline hyperthyroid patients according to thyroid uptake of {sup 99m}Tc-pertechnetate: applicability to unifocal thyroid autonomy?

    Energy Technology Data Exchange (ETDEWEB)

    Reinhardt, Michael J.; Joe, Alexius Y. [University Hospital Bonn, Department of Nuclear Medicine, Bonn (Germany); University Hospital Freiburg, Department of Nuclear Medicine, Hugstetter Str. 55, 79106 Freiburg (Germany); Biermann, Kim; Brockmann, Holger; Mallek, Dirk von; Ezziddin, Samer [University Hospital Bonn, Department of Nuclear Medicine, Bonn (Germany); Wissmeyer, Michael [Inselspital Bern, Department of Nuclear Medicine, 3010 Bern (Switzerland); Juengling, Freimut D.; Krause, Thomas M. [University Hospital Freiburg, Department of Nuclear Medicine, Hugstetter Str. 55, 79106 Freiburg (Germany); Inselspital Bern, Department of Nuclear Medicine, 3010 Bern (Switzerland)

    2006-05-15

    The aim of this study was to evaluate the feasibility of applying a previously described dose strategy based on {sup 99m}Tc-pertechnetate thyroid uptake under thyrotropin suppression (TcTU{sub s}) to radioiodine therapy for unifocal thyroid autonomy. A total of 425 consecutive patients (302 females, 123 males; age 63.1{+-}10.3 years) with unifocal thyroid autonomy were treated at three different centres with {sup 131}I, using Marinelli's formula for calculation of three different absorbed dose schedules: 100-300 Gy to the total thyroid volume according to the pre-treatment TcTU{sub s} (n=146), 300 Gy to the nodule volume (n=137) and 400 Gy to the nodule volume (n=142). Successful elimination of functional thyroid autonomy with either euthyroidism or hypothyroidism occurred at a mean of 12 months after radioiodine therapy in 94.5% of patients receiving 100-300 Gy to the thyroid volume, in 89.8% of patients receiving 300 Gy to the nodule volume and in 94.4% receiving 400 Gy to the nodule volume. Reduction in thyroid volume was highest for the 100-300 Gy per thyroid and 400 Gy per nodule strategies (36{+-}19% and 38{+-}20%, respectively) and significantly lower for the 300 Gy per nodule strategy (28{+-}16%; p<0.01). A dose strategy based on the TcTU{sub s} can be used independently of the scintigraphic pattern of functional autonomous tissue in the thyroid. (orig.)

  20. Efimov states and bound state properties in selected nuclear and molecular three-body systems

    International Nuclear Information System (INIS)

    Huber, H.S.

    1978-01-01

    The search is made among selected three-body systems for possible Efimov state behavior. In order to carry out this analysis of phenomenological potentials a new mathematical approach, the FCM (Faddeev-coordinate-momentum) technique, is developed. The analysis then proceeds through the framework of the Faddeev equations by employing the UPE (unitary pole expansion) to reduce these equations to numerically feasible form. The systems chosen for analysis are the 4 He trimer and the three-α model of 12 C. Efimov states are not found in 12 C, thus answering speculation among nuclear theorists. The 4 He trimer, on the other hand, manifests Efimov states for each potential considered and the characteristics of these states are extensively analyzed. Since Efimov states are predicted by all of the phenomenological potentials considered, these states would seem to be a realistically fundamental property of the 4 He trimer system

  1. ASSESSMENT OF SELECTED PROPERTIES OF NORMAL CONCRETES WITH THE GRINDED RUBBER FROM WORN OUT VEHICLE TYRES

    Directory of Open Access Journals (Sweden)

    Ewa Ołdakowska

    2015-07-01

    Full Text Available Rubber from the worn tyres is associated with a useless material, strenuous for environment, whose most popular recovery method until recently was storage (currently forbidden by law. The adoption and dissemination of new ecological standards, created not only by the European and national legislation, but also developing as a result of expanding ecological consciousness, forces the necessity of seeking efficient methods of utilization of the vehicle tyres. The exemplary solution for the problem of tyres withdrawn from the operation, presented in the article, is using them in the grinded form as a substitute for the natural aggregate for the production of normal concrete. The article presents the results of the tests of selected properties of the modified normal concrete, upon the basis of which it has been found that the rubber causes decrease of compression strength, concrete weight, limits water absorbability, and does not influence significantly the physical and chemical phenomena accompanying the composite structure formation.

  2. Diffusion, Thermal Properties and Chemical Compatibilities of Select MAX Phases with Materials For Advanced Nuclear Systems

    Energy Technology Data Exchange (ETDEWEB)

    Barsoum, Michel [Drexel Univ., Philadelphia, PA (United States); Bentzel, Grady [Drexel Univ., Philadelphia, PA (United States); Tallman, Darin J. [Drexel Univ., Philadelphia, PA (United States); Sindelar, Robert [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Garcia-Diaz, Brenda [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hoffman, Elizabeth [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-04-04

    The demands of Gen IV nuclear power plants for long service life under neutron irradiation at high temperature are severe. Advanced materials that would withstand high temperatures (up to 1000+ ºC) to high doses in a neutron field would be ideal for reactor internal structures and would add to the long service life and reliability of the reactors. The objective of this work is to investigate the chemical compatibility of select MAX with potential materials that are important for nuclear energy, as well as to measure the thermal transport properties as a function of neutron irradiation. The chemical counterparts chosen for this work are: pyrolytic carbon, SiC, U, Pd, FLiBe, Pb-Bi and Na, the latter 3 in the molten state. The thermal conductivities and heat capacities of non-irradiated MAX phases will be measured.

  3. State-selective multireference coupled-cluster theory: In pursuit of property calculation

    International Nuclear Information System (INIS)

    Ghose, K.B.; Piecuch, P.; Pal, S.; Adamowicz, L.

    1996-01-01

    In this work, we examine the efficiency of the recently developed [P. Piecuch et al., J. Chem. Phys. 99, 6732 (1993)] state-selective (SS) multi-reference (MR) coupled-cluster (CC) method for calculation of molecular properties. In our earlier papers, we demonstrated that the SSMRCC method with inclusion of single, double, and internal and semi-internal triple excitations [SSCCSD(T) approach] is capable of providing an accurate description of the ground-state potential energy surfaces. In this paper, we present the dipole moment and polarizability values of the HF molecule at equilibrium and stretched geometries calculated using finite field technique and SSCCSD(T) ansatz. The calculations use double zeta quality basis sets with and without polarization functions. Molecular orbital basis sets include both relaxed and nonrelaxed orbitals. copyright 1996 American Institute of Physics

  4. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... for a thyroid scan is 30 minutes or less. Thyroid Uptake You will be given radioactive iodine ( ... for each thyroid uptake is five minutes or less. top of page What will I experience during ...

  5. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... uptake measurements are obtained at different times. For example, you may have uptake measurements at four to ... medicine procedures can be time consuming. It can take several hours to days for the radiotracer to ...

  6. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... Scan and Uptake Thyroid scan and uptake uses small amounts of radioactive materials called radiotracers, a special ... is a branch of medical imaging that uses small amounts of radioactive material to diagnose and determine ...

  7. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... radioactive iodine uptake test (RAIU) is also known as a thyroid uptake. It is a measurement of ... potential to identify disease in its earliest stages as well as a patient’s immediate response to therapeutic ...

  8. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... known as a thyroid uptake. It is a measurement of thyroid function, but does not involve imaging. ... eating can affect the accuracy of the uptake measurement. Jewelry and other metallic accessories should be left ...

  9. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... Uptake? A thyroid scan is a type of nuclear medicine imaging. The radioactive iodine uptake test (RAIU) ... of thyroid function, but does not involve imaging. Nuclear medicine is a branch of medical imaging that ...

  10. Clustering Properties of Emission Line Selected Galaxies over the past 12.5 Gyrs

    Science.gov (United States)

    Khostovan, Ali Ahmad; Sobral, David; Mobasher, Bahram; Best, Philip N.; Smail, Ian; Matthee, Jorryt; Darvish, Behnam; Nayyeri, Hooshang; Hemmati, Shoubaneh; Stott, John P.

    2018-01-01

    In this talk, I will present my latest results on the clustering and dark matter halo (DMH) mass properties of ~7000 narrowband-selected [OIII] and [OII] emitters. I will briefly describe the past work that has been done with our samples (e.g., luminosity functions, evolution of equivalent widths) as motivation of using [OIII] and [OII] emitters to study clustering/halo properties. My talk will focus on our findings regarding the line luminosity and stellar mass dependencies with DMH mass. We find strongly increasing and redshift-independent trends between line luminosity and DMH mass with evidence for a shallower slope at the bright end consistent with halo masses of ~ 1012.5-13 M⊙. Similar, but weaker, trends between stellar mass and halo mass have also been found. We investigate the inter-dependencies of these trends on halo mass and find that the correlation with line luminosity is stronger than with stellar mass. This suggest that active galaxies may be connected with their host DMHs simply based on their emission line luminosity. If time permits, I will briefly present our most recent results using our sample of ~4000 Lyα emitters, where we find similar trends to that seen with the [OIII] and [OII] samples, as well as previous Hα measurements, which suggests galaxies selected based on emission lines may be tracing the same subpopulation of star forming galaxies. I will conclude my talk with an interpretation of this connection and suggest that the shallower slope seen for the brightest emitters is evidence for a transitional halo mass as suggested in models where quenching mechanisms truncate star formation activity and reduce the fraction of star forming galaxies with increasing halo mass.

  11. Microstructure and Properties of Selected Magnesium-Aluminum Alloys Prepared for SPD Processing Technology

    Directory of Open Access Journals (Sweden)

    Cizek L.

    2017-12-01

    Full Text Available A growing interest in wrought magnesium alloys has been noticed recently, mainly due to development of various SPD (severe plastic deformation methods that enable significant refinement of the microstructure and – as a result – improvement of various functional properties of products. However, forming as-cast magnesium alloys with the increased aluminum content at room temperature is almost impossible. Therefore, application of heat treatment before forming or forming at elevated temperature is recommended for these alloys. The paper presents the influence of selected heat treatment conditions on the microstructure and the mechanical properties of the as-cast AZ91 alloy. Deformation behaviour of the as-cast AZ61 alloy at elevated temperatures was analysed as well. The microstructure analysis was performed by means of both light microscopy and SEM. The latter one was used also for fracture analysis. Moreover, the effect of chemical composition modification by lithium addition on the microstructure of the AZ31-based alloy is presented. The test results can be helpful in preparation of the magnesium-aluminum alloys for further processing by means of SPD methods.

  12. Selection of grapevine leaf varieties for culinary process based on phytochemical composition and antioxidant properties.

    Science.gov (United States)

    Lima, Adriano; Bento, Albino; Baraldi, Ilton; Malheiro, Ricardo

    2016-12-01

    Grapevine leaves are an abundant sub-product of vineyards which is devalued in many regions. The objective of this work is to study the antioxidant activity and phytochemical composition of ten grapevine leaf varieties (four red varieties: Tinta Amarela, Tinta Roriz, Touriga Franca, and Touriga Nacional; and six white varieties: Côdega do Larinho, Fernão Pires, Gouveio, Malvasia Fina, Rabigato, and Viosinho) to select varieties to be used as food ingredients. White grapevine leaves revealed higher antioxidant potential. Malvasia Fina reported better antioxidant properties contrasting with Touriga Franca. Phenolic content varied between 112 and 150mgGAEg(-1) of extract (gallic acid equivalents), hydroxycinnamic acid derivatives and flavonols varied between 76 and 108mgCAEg(-1) of extract (caffeic acid equivalents) and 39 and 54mgQEg(-1) of extract (quercetin equivalents). Malvasia Fina is a good candidate for culinary treatment due to its antioxidant properties and composition in bioactive compounds. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Pyrene-Phosphonate Conjugate: Aggregation-Induced Enhanced Emission, and Selective Fe3+ Ions Sensing Properties

    Directory of Open Access Journals (Sweden)

    Sachin D. Padghan

    2017-08-01

    Full Text Available A new pyrene-phosphonate colorimetric receptor 1 has been designed and synthesized in a one-step process via amide bond formation between pyrene butyric acid chloride and phosphonate-appended aniline. The pyrene-phosphonate receptor 1 showed aggregation-induced enhanced emission (AIEE properties in water/acetonitrile (ACN solutions. Dynamic light scattering (DLS characterization revealed that the aggregates of receptor 1 at 80% water fraction have an average size of ≈142 nm. Field emission scanning electron microscopy (FE-SEM analysis confirmed the formation of spherical aggregates upon solvent evaporation. The sensing properties of receptor 1 were investigated by UV-vis, fluorescence emission spectroscopy, and other optical methods. Among the tested metal ions, receptor 1 is capable of recognizing the Fe3+ ion selectively. The changes in spectral measurements were explained on the basis of complex formation. The composition of receptor 1 and Fe3+ ions was determined by using Job’s plot and found to be 1:1. The receptor 1–Fe3+ complex showed a reversible UV-vis response in the presence of EDTA.

  14. Selected properties of the potato snacks expanded in the microwave radiation

    Directory of Open Access Journals (Sweden)

    Mitrus Marcin

    2018-01-01

    Full Text Available The results of measurements of the selected properties of the extruded potato pellets and snacks expanded in the microwave field are presented in the paper. The potato pellets with the addition of the baking soda were prepared with a single screw extruder TS-45. The snacks were obtained by pellets expansion in a conventional microwave oven. The expansion index and the hardness of the pellets and the snacks, as well as, the texture properties of the snacks were evaluated during this study. The results showed that baking soda addition reduced the potato pellet expansion during their extrusion. This was an effect of a smaller thickness of the obtained pellets. The addition of baking soda had positive influence on potato snacks expansion in microwave radiation. The higher content of the soda additive resulted in lower hardness of pellets during cutting tests. The opposite effect was observed during texture measurements of the snacks. The addition of baking soda increased hardness of the expanded snacks. Soda addition lowers crispness and fragilityof the potato snacks expanded in the microwave radiation.

  15. Selective recognition of palladium based on functional mono phthalocyanines; synthesis, characterization and photophysical properties

    Energy Technology Data Exchange (ETDEWEB)

    Yaraşir, M. Nilüfer; Aytekin, Ahmet [Department of Chemistry, Sakarya University, TR54187 Serdivan, Sakarya (Turkey); Kandaz, Mehmet, E-mail: mkandaz@sakarya.edu.tr [Department of Chemistry, Sakarya University, TR54187 Serdivan, Sakarya (Turkey); Güney, Orhan [Istanbul Technical University, Department of Chemistry, 34469 Maslak, Istanbul (Turkey)

    2016-09-15

    We report the synthesis and photophysical properties of 4,5-bis(2-((Z)-(3-hydroxynaphthalen-2-yl) methyleneamino)phenylthio)phthalonitrile ligand (SB) and its star-type functional zincphthalocyanine (SB-ZnPc) compound obtained by the condensation of 2,3,9,10,16,17,23,24-octakis-(2-aminophenylthio)zincphthlocyanines (A-ZnPc) and 1-hydroxy-2-naphthaldehyde (HNA). Each compound was purified and characterized by elemental analysis, FTIR, {sup 1}H NMR, {sup 13}C NMR, UV/vis and MS (Maldi-TOF) spectral data. SB-ZnPc bearing fluorescent SB moieties on the periphery shows selective palladium ion sensing behavior by acting as hard core upon interaction. Electronic spectra of the SB-ZnPc displays pronounced changes in both absorption and fluorescence spectra upon interaction with Pd{sup 2+} ion. The fluorescence of the SB-ZnPc compound is effectively quenched by treatment with Pd{sup 2+} in THF solution. The solvent effect on the photophysical properties of the SB-ZnPc and interference effect of foreign metal ions were also investigated.

  16. Physical properties and microstructure study of stainless steel 316L alloy fabricated by selective laser melting

    Science.gov (United States)

    Islam, Nurul Kamariah Md Saiful; Harun, Wan Sharuzi Wan; Ghani, Saiful Anwar Che; Omar, Mohd Asnawi; Ramli, Mohd Hazlen; Ismail, Muhammad Hussain

    2017-12-01

    Selective Laser Melting (SLM) demonstrates the 21st century's manufacturing infrastructure in which powdered raw material is melted by a high energy focused laser, and built up layer-by-layer until it forms three-dimensional metal parts. SLM process involves a variation of process parameters which affects the final material properties. 316L stainless steel compacts through the manipulation of building orientation and powder layer thickness parameters were manufactured by SLM. The effect of the manipulated parameters on the relative density and dimensional accuracy of the 316L stainless steel compacts, which were in the as-build condition, were experimented and analysed. The relationship between the microstructures and the physical properties of fabricated 316L stainless steel compacts was investigated in this study. The results revealed that 90° building orientation has higher relative density and dimensional accuracy than 0° building orientation. Building orientation was found to give more significant effect in terms of dimensional accuracy, and relative density of SLM compacts compare to build layer thickness. Nevertheless, the existence of large number and sizes of pores greatly influences the low performances of the density.

  17. Selected properties of laser cladding coatings shaped using Flow drill technology

    Directory of Open Access Journals (Sweden)

    Bartkowski Dariusz

    2017-01-01

    Full Text Available The paper presents the investigations of selected chemical and mechanical properties as well as macro- and microstructure of materials formed using thermal drilling process (Flow drill. The aim of this study was to determine the microstructure of the coatings produced using laser cladding with powder technology. The coatings were produced on the low-carbon steel using 1 kW disc laser. After modification of surface, the thermal drilling process was applied. To produce all coatings, the pure copper powder was used. In this study the laser power equal of 500, 700 and 900 W were used. The microstructure, chemical composition (EDS and microhardness were investigation. It was found that the surface modification of low carbon steel and next conducted thermal drilling process caused change the surface properties on the hole flange. It was found that surface modification of steel using laser cladding with cooper powder and next Flow drill process contributes to the change in microhardness and chemical composition on hole flange.

  18. Microstructure and mechanical properties of stainless steel/calcium silicate composites manufactured by selective laser melting.

    Science.gov (United States)

    Zheng, Zeng; Wang, Lianfeng; Jia, Min; Cheng, Lingyu; Yan, Biao

    2017-02-01

    Selective laser melting (SLM) is raised as one kind of additive manufacturing (AM) which is based on the discrete-stacking concept. This technique can fabricate advanced composites with desirable properties directly from 3D CAD data. In this research, 316L stainless steel (316L SS) and different fractions of calcium silicate (CaSiO 3 ) composites (weight fractions of calcium silicate are 0%, 5%,10% and 15%, respectively) were prepared by SLM technique with a purpose to develop biomedical metallic materials. The relative density, tensile, microhardness and elastic modulus of the composites were tested, their microstructures and fracture morphologies were observed using optical microscope (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). It was found that the addition of CaSiO 3 particles influenced the microstructure and mechanical properties of specimens significantly. The CaSiO 3 precipitates from the overlap of adjacent tracks and became the origin of the defects. The tensile strength of specimens range 320-722MPa. The microhardness and elastic modulus are around 250HV and 215GPa respectively. These composites were ductile materials and the fracture mode of the composites was mixed mode of ductile and brittle fracture. The 316L SS/CaSiO 3 composites can be a potential biomedical metallic materials in the medical field. Copyright © 2016. Published by Elsevier B.V.

  19. Zinc availability in relation to selected soil properties in a crude oil polluted eutric tropofluvent

    International Nuclear Information System (INIS)

    Chukwuma, M.C.; Eshett, E.T.; Onweremadu, E.U.; Okon, M.A.

    2010-01-01

    This study examined zinc availability in crude oil-polluted soils. The aim of the study was to determine the effect of zinc on the physiochemical properties of soils in relation to remediation activities. The study was located at a site in Nigeria where crude oil spillage had occurred over a period of 2 months. The region was characterized by quarternary, alluvium, meander belt, wooded back swamps as well as fresh water swamps and Sombreiro-Warri Deltaic plains with large deposits of petroleum and natural gas. Three different land units were studied, notably (1) unpolluted, (2) polluted without vegetation and (3) polluted with vegetation. Soil sampling was conducted using a transect method. Hydrometer analyses were conducted to determine particle size distribution, while a core method was used to determine bulk density. Soil pH, total carbon, phosphorus, and total nitrogen were also measured. An analysis of variance (ANOVA) was used to correlate and regress zinc availability against the selected soil properties. The study showed that zinc availability increased with increases in the value of the effective carbon cation exchange capacity in the unpolluted and polluted samples without vegetation. Zinc decreased with increased clay and organic matter content. Results suggested that soils must be reclaimed quickly in order to prevent additional degradation. 48 refs., 5 tabs., 4 figs.

  20. Zinc availability in relation to selected soil properties in a crude oil polluted eutric tropofluvent

    Energy Technology Data Exchange (ETDEWEB)

    Chukwuma, M.C.; Eshett, E.T.; Onweremadu, E.U.; Okon, M.A. [Federal Univ. of Technology, Owerri (Nigeria). Dept. of Soil Science and Technology

    2010-04-01

    This study examined zinc availability in crude oil-polluted soils. The aim of the study was to determine the effect of zinc on the physiochemical properties of soils in relation to remediation activities. The study was located at a site in Nigeria where crude oil spillage had occurred over a period of 2 months. The region was characterized by quarternary, alluvium, meander belt, wooded back swamps as well as fresh water swamps and Sombreiro-Warri Deltaic plains with large deposits of petroleum and natural gas. Three different land units were studied, notably (1) unpolluted, (2) polluted without vegetation and (3) polluted with vegetation. Soil sampling was conducted using a transect method. Hydrometer analyses were conducted to determine particle size distribution, while a core method was used to determine bulk density. Soil pH, total carbon, phosphorus, and total nitrogen were also measured. An analysis of variance (ANOVA) was used to correlate and regress zinc availability against the selected soil properties. The study showed that zinc availability increased with increases in the value of the effective carbon cation exchange capacity in the unpolluted and polluted samples without vegetation. Zinc decreased with increased clay and organic matter content. Results suggested that soils must be reclaimed quickly in order to prevent additional degradation. 48 refs., 5 tabs., 4 figs.

  1. Evaluation of the attenuating properties of selected Greek clays for toxic inorganic elements in landfill sites.

    Science.gov (United States)

    Mimides, T; Perraki, T

    2000-05-15

    Heavy metal attenuation properties of selected clay material collected from miscellaneous Greek sites is investigated and tested in the laboratory for their suitability, either as liners in hydrologically unsafe sites or as earth covers for sanitary landfill sites. Eleven potentially hazardous elements (As, Be, Cd, Cr, Cu, Hg, Ni, Pb, Se, V, and Zn) generated by a co-disposal landfill leachate have been considered. Experimental column and static equilibrium methods for the determination of dispersion and adsorption are described. Molecular diffusion dominates the migration phenomena with a velocity range between 1.3 x 10(-5) and 3.5 x 10(-4) cm/s throughout the experiments. A simple way to evaluate dispersion coefficients from breakthrough curves gave values of between 3.90 x 10(-6) and 3.5 x 10(-4) cm2/s, with a mean value of 1.5 x 10(-5). Static adsorption equilibrium studies supported by column runs showed that Freundlich (F = kCn) isotherms express in a better way the assimilative capacities of the tested clays, with k and n values ranging from 0.06 to 1.99 and 0.55 to 1.48 correspondingly. Mathematical models involving non-linear parabolic equations are involved. The experimental data, together with finite difference techniques and some physical clay characteristics, produced trilinear textural diagrams and predictive flow transport convection-dispersion breakthrough curves for a quick estimation of the attenuating properties of clays for heavy metals.

  2. Selected monitoring properties of agricultural soil from the Imielin experimental site

    Directory of Open Access Journals (Sweden)

    Maja Radziemska

    2016-07-01

    Full Text Available The effects of two types of agricultural practice: (1 Variable Rate Application (VRA and (2 uniform (UNI N dose on selected chemical properties of soil were compared in a field fertilization experiment. Nitrogen, in doses 60 or 80 kgN.ha-1 (UNI, and 55-105 kgN.ha-1 (VRA was applied to soil farmed with winter wheat (Triticum aestivum L.. The research was conducted in the 2012/2013 growing season in Poland on 22 ha of production fields located in the Imielin countryside (central Poland. The soil samples were taken from three depths: 0.0-0.3 m, 0.3-0.6 m, and 0.6-0.9 m, and the pH, HAC, TEB, CEC, and BS were determined. The application of the nitrogen fertilizer in the two types of agricultural practice - Variable Rate Application (VRA and uniform (UNI N dose modified the basic physical and chemical properties of soil. The highest values of pH and hydrolytic acidity were observed at the soil depth of 0.6-0.9 m after the first rate of nitrogen fertilizer was applied. Cation exchange capacity of soils collected after uniform nitrogen rates were characterized by values decreasing with the increasing depth of the soil profile.

  3. RESEARCH ON THE INFLUENCE OF BLOWING AGENT ON SELECTED PROPERTIES OF EXTRUDED CELLULAR PRODUCTS

    Directory of Open Access Journals (Sweden)

    Tomasz Garbacz

    2015-11-01

    Full Text Available As a part of a more comprehensive research project, the present study was undertaken to investigate the effect of the type and content of blowing agents in the polymeric materials being processed on the structure and selected physical and mechanical properties of the obtained extrusion parts. In the experiment, the content of the blowing agent (0–2.0% by mass, fed into the processed polymer were adopted as a variable factor. In the studies presented in the article, the blowing agents of endothermic decomposition characteristics (Hydrocerol BIH 70, Hydrocerol BM 70 and the exothermic decomposition characteristics (PLC 751 occurring in the granulated form with a diameter of 1.2 to 1.8 mm were used. Based on the results of investigating porosity, porous structure image analysis as well as microscopic examination of the structure, it has been found that the favorable content of the blowing agent in the polymeric material should be of up to 0.8% by mass. With such a content of the blowing agent in the polymeric material, favorable strength properties are retained in porous parts, the pore distribution is uniform and the pores have similar sizes.

  4. Influence of Annealing on Mechanical Properties of Al-20Si Processed by Selective Laser Melting

    Directory of Open Access Journals (Sweden)

    Pan Ma

    2014-01-01

    Full Text Available The microstructure and mechanical properties of Al-20Si produced by selective laser melting (SLM are investigated for different heat treatment conditions. As a result of the high cooling rate during processing, the as-built SLM material displays a microstructure consisting of a supersaturated Al(Si solid solution along with heavily refined eutectic Si and Si particles. The Si particles become coarser, and the eutectic Si gradually changes its morphology from fibrous to plate-like shape with increasing annealing temperature. The microstructural variations occurring during heat treatment significantly affect the mechanical behavior of the samples. The yield and ultimate strengths decrease from 374 and 506 MPa for the as-built SLM material to 162 and 252 MPa for the sample annealed at 673 K, whereas the ductility increases from 1.6 to 8.7%. This offers the possibility to tune microstructure and corresponding properties of the Al-20Si SLM parts to meet specific requirements.

  5. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... for a thyroid scan is 30 minutes or less. Thyroid Uptake You will be given radioactive iodine (I-123 or I-131) in liquid or capsule form to swallow. The thyroid uptake will begin several hours to 24 hours later. Often, two separate uptake ...

  6. Processing and properties of pressable ceramic with non-uniform reinforcement for selective-toughening

    Energy Technology Data Exchange (ETDEWEB)

    Yi, Wei [School of Mechanical and Chemical Engineering, The University of Western Australia, Perth, WA 6009 (Australia); School of Dentistry, The University of Western Australia, WA 6009 (Australia); Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Shenyang 110004 (China); Hu, Xiaozhi, E-mail: xiao.zhi.hu@uwa.edu.au [School of Mechanical and Chemical Engineering, The University of Western Australia, Perth, WA 6009 (Australia); Ichim, Paul [School of Dentistry, The University of Western Australia, WA 6009 (Australia); Sun, Xudong [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), Northeastern University, Shenyang 110004 (China)

    2012-12-15

    Brittle low-strength and low-toughness pressable dental ceramic can be reinforced by ductile elongated gold-particles (GP). A customized crown structure can be adequately strengthened by distributing GP only in critical sections of the crown, where high tensile stresses are experienced. In the present study, a non-uniformly structured ceramic-matrix composite with excellent interfacial bonding, twofold fracture toughness and strength at desired locations, is fabricated using pressable dental ceramic and GP. The layout pattern and sequence of different GP/ceramic powder mixtures, high-temperature flow properties of these mixtures during hot-pressing and the sample mold geometry are used to control the distribution and locations of GP for selective toughening and strengthening. Nano-crystalline structures of the pressable ceramic-matrix and the nano-scaled interfacial region around GP have been revealed by high-magnification field-emission scanning electron microscopy. Toughening and strengthening mechanisms of the elongated GP including residual stresses from composite processing and ductile fracture of GP are discussed together with SEM observations. Bulk flexural strength and local micro-indentation fracture and deformation characteristics of the selective-toughened ceramic/metal composite have been compared to those of the monolithic pressable ceramic to validate the toughening and strengthening mechanisms.

  7. Processing and properties of pressable ceramic with non-uniform reinforcement for selective-toughening

    International Nuclear Information System (INIS)

    Yi, Wei; Hu, Xiaozhi; Ichim, Paul; Sun, Xudong

    2012-01-01

    Brittle low-strength and low-toughness pressable dental ceramic can be reinforced by ductile elongated gold-particles (GP). A customized crown structure can be adequately strengthened by distributing GP only in critical sections of the crown, where high tensile stresses are experienced. In the present study, a non-uniformly structured ceramic–matrix composite with excellent interfacial bonding, twofold fracture toughness and strength at desired locations, is fabricated using pressable dental ceramic and GP. The layout pattern and sequence of different GP/ceramic powder mixtures, high-temperature flow properties of these mixtures during hot-pressing and the sample mold geometry are used to control the distribution and locations of GP for selective toughening and strengthening. Nano-crystalline structures of the pressable ceramic–matrix and the nano-scaled interfacial region around GP have been revealed by high-magnification field-emission scanning electron microscopy. Toughening and strengthening mechanisms of the elongated GP including residual stresses from composite processing and ductile fracture of GP are discussed together with SEM observations. Bulk flexural strength and local micro-indentation fracture and deformation characteristics of the selective-toughened ceramic/metal composite have been compared to those of the monolithic pressable ceramic to validate the toughening and strengthening mechanisms.

  8. Modification of the Selectivity Properties of Tubular Ceramic Membranes after Alkaline Treatment

    Directory of Open Access Journals (Sweden)

    Patrick Dutournié

    2017-11-01

    Full Text Available This work focuses on the selectivity modification of ceramic membranes after a mild alkaline treatment. Filtration of pure salt-water solutions was carried out with commercial titania membranes before and after the treatment. After treatment, the rejection of NaF significantly decreased, while the rejection of NaCl and NaBr increased. Additionally, NaI and Na2SO4 remained close to zero. Pore size and electrical charge being almost unchanged, only significant modifications in the dielectric effects can explain this modification of selectivity. Therefore, the surface chemistry and the interaction (nature and magnitude with the solvent and with the species present in the solution appear to be modified by the alkaline treatment. This trend is also illustrated by discussing the electric and the dielectric properties that were numerically identified before and after treatment. The alkaline treatment significantly decreased the apparent dielectric constant of NaCl-water solution in the pore, highlighting the rejection of sodium chloride. Contrariwise, the modification of the surface chemistry increased the apparent dielectric constant of NaF-water solution by promoting fluoride transmission.

  9. Facile synthesis of Bi/BiOCl composite with selective photocatalytic properties

    International Nuclear Information System (INIS)

    Chen, Dongling; Zhang, Min; Lu, Qiuju; Chen, Junfang; Liu, Bitao; Wang, Zhaofeng

    2015-01-01

    This paper presents a novel and facile method to fabricate Bi/BiOCl composites with dominant (001) facets in situ via a microwave reduction route. Different characterization techniques, including X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), transmission scanning electron microscopy (TEM), UV–vis diffuse reflectance spectrometry (DRS), X-ray photoelectron spectroscopy (XPS), electron spin resonance spectroscopy (ESR), cathodoluminescence spectrum (CL), and lifetime, have been employed to investigate the structure, optical and electrical properties of the Bi/BiOCl composites. The experimental results show that the introduction of Bi particles can efficiently enhance the photocatalytic performance of BiOCl for the degradation of several dyes under ultraviolet (UV) light irradiation, especially for negative charged methyl orange (MO). Unlike the UV photocatalytic performance, such Bi/BiOCl composite shows higher degradation efficiency towards rhodamine B (RhB) than MO and methylene blue (MB) under visible light irradiation. This special photocatalytic performance can be ascribed to the synergistic effect between oxygen vacancies and Bi particles. This work provides new insights about the photodegradation mechanisms of MO, MB and RhB under UV and visible light irradiation, which would be helpful to guide the selection of an appropriate catalyst for other pollutants. - Highlights: • Bi/BiOCl composites were synthesized via a microwave reduction. • Tunable selectivity photocatalytic activity can be achieved. • Photodegradation mechanism under UV and visible light were proposed

  10. CONSEXPO 3.0, consumer exposure and uptake models

    NARCIS (Netherlands)

    Veen MP van; LBM

    2001-01-01

    The report provides a modelling approach to consumer exposure to chemicals, based on mathematical contact, exposure and uptake models. For each route of exposure, a number of exposure and uptake models are included. A general framework joins the exposure and uptake models selected by the user. By

  11. Citric acid modifies surface properties of commercial CeO{sub 2} nanoparticles reducing their toxicity and cerium uptake in radish (Raphanus sativus) seedlings

    Energy Technology Data Exchange (ETDEWEB)

    Trujillo-Reyes, J. [Chemistry Department, The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States); Vilchis-Nestor, A.R. [Centro Conjunto de Investigación en Química Sustentable UAEM—UNAM, Carretera Toluca—Atlacomulco km 14.5, San Cayetano, CP 50200 Toluca, Estado de México (Mexico); Majumdar, S. [Chemistry Department, The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States); Peralta-Videa, J.R. [Chemistry Department, The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States); Environmental Science and Engineering PhD program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States); Gardea-Torresdey, J.L., E-mail: jgardea@utep.edu [Chemistry Department, The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States); Environmental Science and Engineering PhD program, The University of Texas at El Paso, 500 West University Ave., El Paso, TX 79968 (United States); University of California Center for Environmental Implications of Nanotechnology (UC CEIN), The University of Texas at El Paso, 500 West University Av., El Paso, TX 79968 (United States)

    2013-12-15

    Highlights: • The citric acid capping significantly reduced the ζ potential values. • As the amount of CA increased, thicker the layer surrounding the CeO{sub 2} NPs. • CeO{sub 2}/CA NPs had better distribution and small particle size than bare CeO{sub 2} NPs. • CeO{sub 2}/CA NPs decrease the Ce uptake by radish seedlings. -- Abstract: Little is known about the mobility, reactivity, and toxicity to plants of coated engineered nanoparticles (ENPs). Surface modification may change the interaction of ENPs with living organisms. This report describes surface changes in commercial CeO{sub 2} NPs coated with citric acid (CA) at molar ratios of 1:2, 1:3, 1:7, and 1:10 CeO{sub 2}:CA, and their effects on radish (Raphanus sativus) seed germination, cerium and nutrients uptake. All CeO{sub 2} NPs and their absorption by radish plants were characterized by TEM, DLS, and ICP-OES. Radish seeds were germinated in pristine and CA coated CeO{sub 2} NPs suspensions at 50 mg/L, 100 mg/L, and 200 mg/L. Deionized water and CA at 100 mg/L were used as controls. Results showed ζ potential values of 21.6 mV and −56 mV for the pristine and CA coated CeO{sub 2} NPs, respectively. TEM images showed denser layers surrounding the CeO{sub 2} NPs at higher CA concentrations, as well as better distribution and smaller particle sizes. None of the treatments affected seed germination. However, at 200 mg/L the CA coated NPs at 1:7 ratio produced significantly (p ≤ 0.05) more root biomass, increased water content and reduced by 94% the Ce uptake, compared to bare NPs. This suggests that CA coating decrease CeO{sub 2} NPs toxicity to plants.

  12. Microstructural Evolution and Mechanical Property Development of Selective Laser Melted Copper Alloys

    Science.gov (United States)

    Ventura, Anthony Patrick

    Selective Laser Melting (SLM) is an additive manufacturing technology that utilizes a high-power laser to melt metal powder and form a part layer-by-layer. Over the last 25 years, the technology has progressed from prototyping polymer parts to full scale production of metal component. SLM offers several advantages over traditional manufacturing techniques; however, the current alloy systems that are researched and utilized for SLM do not address applications requiring high electrical and thermal conductivity. This work presents a characterization of the microstructural evolution and mechanical property development of two copper alloys fabricated via SLM and post-process heat treated to address this gap in knowledge. Tensile testing, conductivity measurement, and detailed microstructural characterization was carried out on samples in the as-printed and heat treated conditions. A single phase solid solution strengthened binary alloy, Cu-4.3Sn, was the first alloy studied. Components were selectively laser melted from pre-alloyed Cu-4.3Sn powder and heat treated at 873 K (600 °C) and 1173 K (900 °C) for 1 hour. As-printed samples were around 97 percent dense with a yield strength of 274 MPa, an electrical conductivity of 24.1 %IACS, and an elongation of 5.6%. Heat treatment resulted in lower yield strength with significant increases in ductility due to recrystallization and a decrease in dislocation density. Tensile sample geometry and surface finish also showed a significant effect on measured yield strength but a negligible change in measured ductility. Microstructural characterization indicated that grains primarily grow epitaxially with a sub-micron cellular solidification sub-structure. Nanometer scale tin dioxide particles identified via XRD were found throughout the structure in the tin-rich intercellular regions. The second alloy studied was a high-performance precipitation hardening Cu-Ni-Si alloy, C70250. Pre-alloyed powder was selectively laser melted to

  13. Preliminary Studies on Existing Scenario of Selected Soil Property in Cheddikulam DS Division Vavuniya, Sri Lanka

    Directory of Open Access Journals (Sweden)

    M.A. R. Aashifa

    2017-01-01

    Full Text Available  This study was conducted to quantify the spatial variability of soil properties, use this information to produce accurate map by means of ordinary kriging and find the ways to reclaim the problem soil and make suggestions to cultivate the crop variety which is suitable for the existing soil property.70 sampling points were selected for that research using stratified random sampling method. Stratification was based on the type of land cover, and following land cover patterns were identified forest patches, agriculture land patches, grass land patches and catchments. Sampling points were randomly selected from each land cover types. Minimum distance between two adjacent sampling points was 500m. Soil samples were analyzed for pH, EC, exchangeable K, available P. In each location, soils were collected from top to - 30 cm depth (root zone using a core sampler and sub soil samples were collected around the geo-reference point to obtain a composite sample. Geostatistical tool of the software (ArcGIS 10.2.2. trail version was used to construct semi-variograms and spatial structure analysis for the variables. Geostatistical estimation had done by kriging. 13% of agriculture land area was acidic soil and 5.7% alkaline soil. 13% of agriculture land area was identified as saline soil. 67.11% of agriculture lands contain more phosphorous concentration than the optimum range. 3.4% agriculture lands contain higher potassium concentration than the optimum range. 98% of forest lands and 100% of grass lands contains phosphorous concentration higher than the optimum range. But forest lands and catchments shows lower level of potassium concentration. 22% of grass lands contain higher potassium than the optimum level. Agriculture practices leads to change in the soil hence identified soil problems should be reclaimed in order to maintain the fertility of soil for sustainable production. Proper management of soil can be a better solution for supporting the

  14. Yoghurts with addition of selected vegetables: acidity, antioxidant properties and sensory quality.

    Science.gov (United States)

    Najgebauer-Lejko, Dorota; Grega, Tadeusz; Tabaszewska, Małgorzata

    2014-01-01

    Yoghurt is a fermented milk of unique sensory, nutritive and dietetic value offered in a variety of types and in different flavours. Vegetables belong to the group of food products rich in antioxidant substances (e.g., vitamin C, carotenoids, tocopherols, polyphenols) which regular consumption lowers the risk of many diseases including cancers and cardiovascular disorders. The aim of the present work was to manufacture and assess the acidity, sensory quality and antioxidant capacity of yoghurts with addition of selected vegetables during 2-week refrigerated storage. The vegetable preparations (carrot, pumpkin, broccoli and red sweet pepper) were added to the cow's milk fermented using DVS type yoghurt culture after initial cooling to 15-20°C in the amount of 10% (w/w). The following analyses were performed: determination of pH, titratable acidity, antioxidant activity by ferric reducing antioxidant power (FRAP) and 2,2'-diphenyl-1-picrylhydrazyl (DPPH) method as well as sensory evaluation and were conducted after 1, 7 and 14 days of cold storage. The yoghurt supplementation with selected vegetables had no significant effect on the pH and titratable acidity level. The highest ability to scavenge DPPH radicals was stated for yoghurts with broccoli and red sweet pepper. The latter treatment gained the highest notes in sensory evaluation. All vegetable yoghurts were characterised by higher than the natural yoghurt FRAP values measured directly after production. However, the level of this parameter significantly decreased after storage. The red sweet pepper additive was the most beneficial regarding antioxidant properties and organoleptic acceptance of the studied yoghurts.

  15. Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar; FINAL

    International Nuclear Information System (INIS)

    Tuskan, G.A.

    2001-01-01

    Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F(sub 2) progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar

  16. Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar

    Energy Technology Data Exchange (ETDEWEB)

    Tuskan, G.A.

    2001-06-20

    Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F2 progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar.

  17. The study of selective property of college student’s learning space

    Science.gov (United States)

    Nagai, Mizuki; Matsumoto, Yuji; Naka, Ryusuke

    2018-05-01

    These days, college students study not only at places designed for learning such as libraries in colleges, but also cafes in downtown while the number of facilities for learning run by colleges is increasing. Then I have researched facilities in college and those in downtown to find selective properties of college students’ learning space. First, I found by questionnaire survey that students chose “3rd place” such as cafes and fast food shops, second to their houses and libraries in college. Next, I found “psychological factor” were also affected their choice. Furthermore, they studied different subjects at different places. In experiments, I researched how effectively they studied each subject at every place. The results show that I find that places you like and places where learning efficiency is good are different. They learned the least effective at “3d place” regardless of what they learned. The result of how long they kept high-level intellectual activity at each place shows that they could work on the study with more motivation at their favorite place and 3rd place. On the other hand, at the 2nd place, they could study rather effectively, but could not keep concentration and motivation for a long time. In this way, college students have 2 patterns of choosing learning space.

  18. Antibacterial properties of biosurfactants against selected Gram-positive and -negative bacteria.

    Science.gov (United States)

    Díaz De Rienzo, Mayri A; Stevenson, Paul; Marchant, Roger; Banat, Ibrahim M

    2016-01-01

    The antibacterial properties and ability to disrupt biofilms of biosurfactants (rhamnolipids, sophorolipids) and sodium dodecyl sulphate (SDS) in the presence and absence of selected organic acids were investigated. Pseudomonas aeruginosa PAO1 was inhibited by sophorolipids and SDS at concentrations >5% v/v, and the growth of Escherichia coli NCTC 10418 was also inhibited by sophorolipids and SDS at concentrations >5% and 0.1% v/v, respectively. Bacillus subtilis NCTC 10400 was inhibited by rhamnolipids, sophorolipids and SDS at concentrations >0.5% v/v of all three; the same effect was observed with Staphylococcus aureus ATCC 9144. The ability to attach to surfaces and biofilm formation of P. aeruginosa PAO1, E. coli NCTC 10418 and B. subtilis NCTC 10400 was inhibited by sophorolipids (1% v/v) in the presence of caprylic acid (0.8% v/v). In the case of S. aureus ATCC 9144, the best results were obtained using caprylic acid on its own. It was concluded that sophorolipids are promising compounds for the inhibition/disruption of biofilms formed by Gram-positive and Gram-negative microorganisms and this activity can be enhanced by the presence of booster compounds such as caprylic acid. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  19. Comparison of selected physico-chemical properties of calcium alginate films prepared by two different methods.

    Science.gov (United States)

    Crossingham, Yazmin J; Kerr, Philip G; Kennedy, Ross A

    2014-10-01

    Sodium alginate (SA) is a naturally occurring, non-toxic, polysaccharide that is able to form gels after exposure to calcium. These gels have been used in food and biomedical industries. This is the first direct comparison of two different methods of calcium alginate film production, namely interfacial gelation (IFG) and dry cast gelation (DCG). IFG films were significantly thicker than DCG films, and were more extensively rehydrated in water and 0.1M HCl than the DCG films. During rehydration in 0.1M HCl almost all calcium ions were lost. Under scanning electron microscopy, IFG films appeared less dense than DCG films. IFG films were mechanically weaker than DCG films, and both types of film were weaker after rehydration in 0.1M HCl compared with deionized water. Permeation of theophylline (TPL) was evaluated in-vitro; the diffusion coefficient (D) of the TPL was almost 90 times lower in DCG films than IFG films when both were rehydrated in water. Although the 0.1M HCl rendered both gels more permeable to TPL, D of TPL was still about five times lower in DCG compared to IFG films. The evaluation of selected physico-chemical properties of films is important, since this information may inform the choice of gelation technique used to produce calcium alginate coatings on pharmaceutical products. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Selective laser melting of carbon/AlSi10Mg composites: Microstructure, mechanical and electronical properties

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Xiao; Song, Bo, E-mail: bosong@hust.edu.cn; Fan, Wenrui; Zhang, Yuanjie; Shi, Yusheng

    2016-04-25

    Carbon nanotubes/AlSi10Mg composites has drawn lots of attention in structural engineering and functional device applications due to its extraordinary high elastic modulus and mechanical strength as well as excellent electrical and thermal conductivities. In this study, the CNTs/AlSi10Mg composites was firstly prepared and then processed by selective laser melting. The powder preparation, SLM process, and microstructure evolution, properties were clarified. The results showed that CNTs were decomposed due to the direct interaction with the laser beam. The SLMed composites displayed a similar microstructure to that of SLMed AlSi10Mg. The common brittleness phase Al{sub 4}C{sub 3} didn't form, and the carbon dispersion strengthening was observed. The electrical resistivity of the composites was reduced significantly and the hardness was improved. - Highlights: • Carbon nanotubes/AlSi10Mg powder were prepared by slurry ball milling process. • Carbon nanotubes/AlSi10Mg composites were firstly prepared by SLM. • The electrical resistivity of the composites was significantly reduced and hardness was improved.

  1. The diffusion properties of ion implanted species in selected target materials

    International Nuclear Information System (INIS)

    Alton, G.D.; Dellwo, J.; Carter, H.K.; Kormicki, J.; Bartolo, G. di; Batchelder, J.C.; Breitenbach, J.; Chediak, J.A.; Jentoff-Nilsen, K.; Ichikawa, S.

    1995-01-01

    Experiments important to the future success of the Holifield Radioactive Ion Beam Facility (HRIBF) are in progress at the Oak Ridge National Laboratory which are designed to select the most appropriate target material for generating a particular radioactive ion beam (RIB). The 25-MV HHIRF tandem accelerator is used to implant stable complements of interesting radioactive elements into refractory targets mounted in a high-temperature FEBIAD ion source which is open-quotes on-lineclose quotes at the UNISOR facility. The intensity versus time of implanted species, which diffuse from the high-temperature target material (∼1700 degrees C) and are ionized in the FEBIAD ion source, is used to determine release times for a particular projectile/target material combination. From such release data, diffusion coefficients can be derived by fitting the theoretical results obtained by computational solution of Fick's second equation to experimental data. The diffusion coefficient can be used subsequently to predict the release properties of the particular element from the same material in other target geometries and at other temperatures, provided that the activation energy is also known. Diffusion coefficients for Cl implanted into and diffused from CeS and Zr 5 Si 3 and As, Br, and Se implanted into and diffused from Zr 5 Ge 3 have been derived from the resulting intensity versus time profiles. Brief descriptions of the experimental apparatus and procedures utilized in the present experiments and plans for future related experiments are presented

  2. Manufacturing Feasibility and Forming Properties of Cu-4Sn in Selective Laser Melting.

    Science.gov (United States)

    Mao, Zhongfa; Zhang, David Z; Wei, Peitang; Zhang, Kaifei

    2017-03-24

    Copper alloys, combined with selective laser melting (SLM) technology, have attracted increasing attention in aerospace engineering, automobile, and medical fields. However, there are some difficulties in SLM forming owing to low laser absorption and excellent thermal conductivity. It is, therefore, necessary to explore a copper alloy in SLM. In this research, manufacturing feasibility and forming properties of Cu-4Sn in SLM were investigated through a systematic experimental approach. Single-track experiments were used to narrow down processing parameter windows. A Greco-Latin square design with orthogonal parameter arrays was employed to control forming qualities of specimens. Analysis of variance was applied to establish statistical relationships, which described the effects of different processing parameters (i.e., laser power, scanning speed, and hatch space) on relative density (RD) and Vickers hardness of specimens. It was found that Cu-4Sn specimens were successfully manufactured by SLM for the first time and both its RD and Vickers hardness were mainly determined by the laser power. The maximum value of RD exceeded 93% theoretical density and the maximum value of Vickers hardness reached 118 HV 0.3/5. The best tensile strength of 316-320 MPa is inferior to that of pressure-processed Cu-4Sn and can be improved further by reducing defects.

  3. Microstructure and Properties of AlSi10Mg Powder for Selective Laser Melting

    Directory of Open Access Journals (Sweden)

    TANG Pengjun

    2018-02-01

    Full Text Available The AlSi10Mg powder was prepared by supersonic gas atomization. After classified, the powder was fabricated into block by selective laser melting (SLM. The microstructure, phase, and evolutions of powder and block were investigated by optical microscope, scanning electron microscope and X-Ray Diffraction. The tensile properties of SLM block were tested by tensile experiments at room temperature. The results show that the size distribution of AlSi10Mg powder after classified can meet the requirements of SLM technology. The powder always is spherical and spherical-like. Meanwhile, the microstructure of powders is fine and uniform, which contain α(Al matrix and (α+Si eutectic. In addition, the melt pool boundaries of SLM block are legible. The microstructure is also uniform and densified, the relative density approaches to 99.5%. On the other hand, only α(Al and few Silicon phase are detected in this condition, due to the most alloying elements are dissolved in α(Al matrix. At room temperature, the ultimate tensile strength of SLM block reaches up to 442 MPa.

  4. JB-9322, a new selective histamine H2-receptor antagonist with potent gastric mucosal protective properties.

    Science.gov (United States)

    Palacios, B; Montero, M J; Sevilla, M A; Román, L S

    1995-05-01

    1. JB-9322 is a selective histamine H2-receptor antagonist with gastric antisecretory activity and mucosal protective properties. 2. The affinity of JB-9322 for the guinea-pig atria histamine H2-receptor was approximately 2 times greater than that of ranitidine. 3. In vivo, the ID50 value for the inhibition of gastric acid secretion in pylorus-ligated rats was 5.28 mg kg-1 intraperitoneally. JB-9322 also dose-dependently inhibited gastric juice volume and pepsin secretion. In gastric lumen-perfused rats, intravenous injection of JB-9322 dose-dependently reduced histamine-, pentagastrin- and carbachol-stimulated gastric acid secretion. 4. JB-9322 showed antiulcer activity against aspirin and indomethacin-induced gastric lesions and was more potent than ranitidine. 5. JB-9322 effectively inhibited macroscopic gastric haemorrhagic lesions induced by ethanol. Intraperitoneal injection was effective in preventing the lesions as well as oral treatment. The oral ID50 value for these lesions was 1.33 mg kg-1. By contrast, ranitidine (50 mg kg-1) failed to reduce these lesions. In addition, the protective effect of JB-9322 was independent of prostaglandin synthesis. 6. These results indicate that JB-9322 is a new antiulcer drug that exerts a potent cytoprotective effect in addition to its gastric antisecretory activity.

  5. Selection and Basic Properties of the Buffer Material for High-Level Radioactive Waste Repository in China

    Institute of Scientific and Technical Information of China (English)

    WEN Zhijian

    2008-01-01

    Radioactive wastes arising from a wide range of human activities are in many different physical and chemical forms, contaminated with varying radioactivity. Their common features are the potential hazard associated with their radioactivity and the need to manage them in such a way as to protect the human environment. The geological disposal is regarded as the most reasonable and effective way to safely disposing high-level radioactive wastes in the world. The conceptual model of geological disposal in China is based on a multi-barrier system that combines an isolating geological environment with an engineered barrier system. The buffer is one of the main engineered barriers for HLW repository. It is expected to maintain its low water permeability, self-sealing property, radio nuclides adsorption and retardation properties, thermal conductivity, chemical buffering property,canister supporting property, and stress buffering property over a long period of time. Bentonite is selected as the main content of buffer material that can satisfy the above requirements. The Gaomiaozi deposit is selected as the candidate supplier for China's buffer material of high level radioactive waste repository. This paper presents the geological features of the GMZ deposit and basic properties of the GMZ Na-bentonite. It is a super-large deposit with a high content of montmorillonite (about 75%), and GMZ-1, which is Na-bentonite produced from GMZ deposit is selected as the reference material for China's buffer material study.

  6. Thyroid uptake test

    International Nuclear Information System (INIS)

    Ganatra, R.D.

    1992-01-01

    The uptake of radioiodine by the thyroid gland is altered by the iodine content of diet or drugs. American diet has a high iodine content because each slice of the white bread contains nearly 150μg of iodine due to the bleaching process employed in the production of the bread. This carrier content of iodine reduces the uptake so much, that the normal American uptakes are usually three to four times lower than the uptakes in the developing countries. The other drawback of the thyroid uptake test is that it is affected by the iodine containing drugs. Anti-diarrhoea medications are quire common in the developing countries and many of them contain iodine moiety. Without a reliable drug history, a low thyroid uptake value may lead to a misleading conclusion

  7. Quantitative uptake of colloidal particles by cell cultures

    Energy Technology Data Exchange (ETDEWEB)

    Feliu, Neus [Department of Physics, Philipps University Marburg, Marburg (Germany); Department for Clinical Science, Intervention and Technology (CLINTEC),Karolinska Institutet, Stockholm (Sweden); Hühn, Jonas; Zyuzin, Mikhail V.; Ashraf, Sumaira; Valdeperez, Daniel; Masood, Atif [Department of Physics, Philipps University Marburg, Marburg (Germany); Said, Alaa Hassan [Department of Physics, Philipps University Marburg, Marburg (Germany); Physics Department, Faculty of Science, South Valley University (Egypt); Escudero, Alberto [Department of Physics, Philipps University Marburg, Marburg (Germany); Instituto de Ciencia de Materiales de Sevilla, CSIC — Universidad de Sevilla, Seville (Spain); Pelaz, Beatriz [Department of Physics, Philipps University Marburg, Marburg (Germany); Gonzalez, Elena [Department of Physics, Philipps University Marburg, Marburg (Germany); University of Vigo, Vigo (Spain); Duarte, Miguel A. Correa [University of Vigo, Vigo (Spain); Roy, Sathi [Department of Physics, Philipps University Marburg, Marburg (Germany); Chakraborty, Indranath [Department of Chemistry, University of Illinois at Urbana Champaign, Urbana, IL (United States); Lim, Mei L.; Sjöqvist, Sebastian [Department for Clinical Science, Intervention and Technology (CLINTEC),Karolinska Institutet, Stockholm (Sweden); Jungebluth, Philipp [Department of Thoracic Surgery, Thoraxklinik, Heidelberg University, Heidelberg (Germany); Parak, Wolfgang J., E-mail: wolfgang.parak@physik.uni-marburg.de [Department of Physics, Philipps University Marburg, Marburg (Germany); CIC biomaGUNE, San Sebastian (Spain)

    2016-10-15

    The use of nanotechnologies involving nano- and microparticles has increased tremendously in the recent past. There are various beneficial characteristics that make particles attractive for a wide range of technologies. However, colloidal particles on the other hand can potentially be harmful for humans and environment. Today, complete understanding of the interaction of colloidal particles with biological systems still remains a challenge. Indeed, their uptake, effects, and final cell cycle including their life span fate and degradation in biological systems are not fully understood. This is mainly due to the complexity of multiple parameters which need to be taken in consideration to perform the nanosafety research. Therefore, we will provide an overview of the common denominators and ideas to achieve universal metrics to assess their safety. The review discusses aspects including how biological media could change the physicochemical properties of colloids, how colloids are endocytosed by cells, how to distinguish between internalized versus membrane-attached colloids, possible correlation of cellular uptake of colloids with their physicochemical properties, and how the colloidal stability of colloids may vary upon cell internalization. In conclusion three main statements are given. First, in typically exposure scenarios only part of the colloids associated with cells are internalized while a significant part remain outside cells attached to their membrane. For quantitative uptake studies false positive counts in the form of only adherent but not internalized colloids have to be avoided. pH sensitive fluorophores attached to the colloids, which can discriminate between acidic endosomal/lysosomal and neutral extracellular environment around colloids offer a possible solution. Second, the metrics selected for uptake studies is of utmost importance. Counting the internalized colloids by number or by volume may lead to significantly different results. Third, colloids

  8. Properties of halogenated and sulfonated porphyrins relevant for the selection of photosensitizers in anticancer and antimicrobial therapies.

    Directory of Open Access Journals (Sweden)

    Barbara Pucelik

    Full Text Available The impact of substituents on the photochemical and biological properties of tetraphenylporphyrin-based photosensitizers for photodynamic therapy of cancer (PDT as well as photodynamic inactivation of microorganisms (PDI was examined. Spectroscopic and physicochemical properties were related with therapeutic efficacy in PDT of cancer and PDI of microbial cells in vitro. Less polar halogenated, sulfonamide porphyrins were most readily taken up by cells compared to hydrophilic and anionic porphyrins. The uptake and PDT of a hydrophilic porphyrin was significantly enhanced with incorporation in polymeric micelles (Pluronic L121. Photodynamic inactivation studies were performed against Gram-positive (S. aureus, E. faecalis, Gram-negative bacteria (E. coli, P. aeruginosa, S. marcescens and fungal yeast (C. albicans. We observed a 6 logs reduction of S. aureus after irradiation (10 J/cm2 in the presence of 20 μM of hydrophilic porphyrin, but this was not improved with incorporation in Pluronic L121. A 2-3 logs reduction was obtained for E. coli using similar doses, and a decrease of 3-4 logs was achieved for C. albicans. Rational substitution of tetraphenylporphyrins improves their photodynamic properties and informs on strategies to obtain photosensitizers for efficient PDT and PDI. However, the design of the photosensitizers must be accompanied by the development of tailored drug formulations.

  9. Description, Properties, and Degradation of Selected Volatile Organic Compounds Detected in Ground Water--A Review of Selected Literature

    Science.gov (United States)

    Lawrence, Stephen J.

    2006-01-01

    This report provides abridged information describing the most salient properties and biodegradation of 27 chlorinated volatile organic compounds detected during ground-water studies in the United States. This information is condensed from an extensive list of reports, papers, and literature published by the U.S. Government, various State governments, and peer-reviewed journals. The list includes literature reviews, compilations, and summaries describing volatile organic compounds in ground water. This report cross-references common names and synonyms associated with volatile organic compounds with the naming conventions supported by the International Union of Pure and Applied Chemistry. In addition, the report describes basic physical characteristics of those compounds such as Henry's Law constant, water solubility, density, octanol-water partition (log Kow), and organic carbon partition (log Koc) coefficients. Descriptions and illustrations are provided for natural and laboratory biodegradation rates, chemical by-products, and degradation pathways.

  10. Preoperative [18F]-fluorodeoxyglucose positron emission tomography standardized uptake value of neck lymph nodes may aid in selecting patients with oral cavity squamous cell carcinoma for salvage therapy after relapse

    International Nuclear Information System (INIS)

    Liao, Chun-Ta; Huang, Shiang-Fu; Chen, I. How; Chang, Joseph Tung-Chieh; Wang, Hung-Ming; Ng, Shu-Hang; Hsueh, Chuen; Lee, Li-Yu.; Lin, Chih-Hung; Cheng, Ann-Joy; Yen, Tzu-Chen

    2009-01-01

    Relapse of tumours in patients with oral cavity squamous cell carcinoma (OSCC) is associated with a dismal outcome. In this prospective study, we sought to investigate the clinical significance of the preoperative maximal standardized uptake value (SUVmax) at the neck lymph nodes in selecting patients with OSCC for salvage therapy after relapse. Between 2002 and 2007, 108 patients with early relapse of OSCC (n=75) or late relapse of OSCC (n=33) were identified. Salvage therapy was performed in 47 patients. All patients underwent 2-deoxy-2[ 18 F]-fluoro-d-glucose positron emission tomography during the 2 weeks before surgery and neck dissection. All patients were followed for 12 months or more after surgery or until death. The optimal cut-off value for the neck lymph node SUVmax (SUVnodal-max) was selected according to the 5-year disease-specific survival (DSS) rate. Independent risk factors were identified by Cox regression analysis. The mean follow-up for all patients was 20.3 months (41.1 months for surviving patients). In the early relapse group, several prognostic factors were identified in univariate and multivariate analyses, including a SUVnodal-max value of ≥4.2. A scoring system based on univariate analysis was formulated. Patients with a score of 0 had a better 5-year DSS than those with scores of 1 or higher (58% vs. 5%, p=0.0003). In patients with late relapse, a SUVnodal-max value of ≥4.2 had the highest prognostic value for predicting the 5-year DSS (45% vs. 0%, p=0.0005). Among patients with relapsed OSCC, the SUVnodal-max value may aid in selecting patients for salvage therapy. (orig.)

  11. Computer simulation of the relationship between selected properties of laser remelted tool steel surface layer

    Energy Technology Data Exchange (ETDEWEB)

    Bonek, Mirosław, E-mail: miroslaw.bonek@polsl.pl; Śliwa, Agata; Mikuła, Jarosław

    2016-12-01

    Highlights: • Prediction of the properties of laser remelted surface layer with the use of FEM analysis. • The simulation was applied to determine the shape of molten pool of remelted surface. • Applying of numerical model MES for simulation of surface laser treatment to meaningfully shorten time of selection of optimum parameters. • An FEM model was established for the purpose of building a computer simulation. - Abstract: Investigations >The language in this paper has been slightly changed. Please check for clarity of thought, and that the meaning is still correct, and amend if necessary.include Finite Element Method simulation model of remelting of PMHSS6-5-3 high-speed steel surface layer using the high power diode laser (HPDL). The Finite Element Method computations were performed using ANSYS software. The scope of FEM simulation was determination of temperature distribution during laser alloying process at various process configurations regarding the laser beam power and method of powder deposition, as pre-coated past or surface with machined grooves. The Finite Element Method simulation was performed on five different 3-dimensional models. The model assumed nonlinear change of thermal conductivity, specific heat and density that were depended on temperature. The heating process was realized as heat flux corresponding to laser beam power of 1.4, 1.7 and 2.1 kW. Latent heat effects are considered during solidification. The molten pool is composed of the same material as the substrate and there is no chemical reaction. The absorptivity of laser energy was dependent on the simulated materials properties and their surface condition. The Finite Element Method simulation allows specifying the heat affected zone and the temperature distribution in the sample as a function of time and thus allows the estimation of the structural changes taking place during laser remelting process. The simulation was applied to determine the shape of molten pool and the

  12. Financial Reporting by Selected Defense Agencies of Government Property in the Custody of Contractors

    National Research Council Canada - National Science Library

    1997-01-01

    ... over the $92 billion of Government property in the custody of contractors. After several years of planning, DoD has not developed a standard accounting system for recording, tracking, and reporting Government property in the custody of contractors...

  13. Molecular origin of the selectivity differences between palladium and gold-palladium in benzyl alcohol oxidation: Different oxygen adsorption properties

    Energy Technology Data Exchange (ETDEWEB)

    Savara, Aditya Ashi [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Chan-Thaw, Carine E. [Univ. degli Studi di Milano, Milano (Italy); Sutton, Jonathan E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wang, Di [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany); Prati, Laura [Univ. degli Studi di Milano, Milano (Italy); Villa, Alberto [Univ. degli Studi di Milano, Milano (Italy)

    2016-12-22

    The same mechanism and microkinetic model used for benzyl alcohol oxidation over Pd/C was shown to apply to benzyl alcohol oxidation over AuPd/C. Almost all of the selectivity differences could be explained by a decrease in oxygen adsorption on AuPd. After isolating oxygen adsorption as being the origin of the selectivity differences, density functional theory was used to investigate the oxygen adsorption properties of a pure Pd surface, a pure Au surface, and an alloyed AuPd surface. Finally, the calculations showed that Au–Pd alloying decreased the oxygen adsorption properties relative to pure Pd, which explained the selectivity differences, consistent with the microkinetic modeling.

  14. Multiple pathways of sigma(1) receptor ligand uptakes into primary cultured neuronal cells.

    Science.gov (United States)

    Yamamoto, H; Karasawa, J; Sagi, N; Takahashi, S; Horikomi, K; Okuyama, S; Nukada, T; Sora, I; Yamamoto, T

    2001-08-03

    Although many antipsychotics have affinities for sigma receptors, the transportation pathway of exogenous sigma(1) receptor ligands to intracellular type-1 sigma receptors are not fully understood. In this study, sigma(1) receptor ligand uptakes were studied using primary cultured neuronal cells. [(3)H](+)-pentazocine and [(3)H](R)-(+)-1-(4-chlorophenyl)-3-[4-(2-methoxyethyl)piperazin-1-yl]methyl-2-pyrrolidinone L-tartrate (MS-377), used as a selective sigma(1) receptor ligands, were taken up in a time-, energy- and temperature-dependent manner, suggesting that active transport mechanisms were involved in their uptakes. sigma(1) receptor ligands taken up into primary cultured neuronal cells were not restricted to agonists, but also concerned antagonists. The uptakes of these ligands were mainly Na(+)-independent. Kinetic analysis of [(3)H](+)-pentazocine and [(3)H]MS-377 uptake showed K(m) values (microM) of 0.27 and 0.32, and V(max) values (pmol/mg protein/min) of 17.4 and 9.4, respectively. Although both ligands were incorporated, the pharmacological properties of these two ligands were different. Uptake of [(3)H](+)-pentazocine was inhibited in the range 0.4-7.1 microM by all the sigma(1) receptor ligands used, including N,N-dipropyl-2-[4-methoxy-3-(2-phenylethoxy)phenyl]ethylamine monohydrochloride (NE-100), a selective sigma(1) receptor ligand. In contrast, the inhibition of [(3)H]MS-377 uptake was potently inhibited by haloperidol, characterized by supersensitivity (IC(50), approximately 2 nM) and was inhibited by NE-100 with low sensitivity (IC(50), 4.5 microM). Moreover, kinetic analysis revealed that NE-100 inhibited [(3)H]MS-377 uptake in a noncompetitive manner, suggesting that NE-100 acted at a site different from the uptake sites of [(3)H]MS-377. These findings suggest that there are at least two uptake pathways for sigma(1) receptor ligands in primary cultured neuronal cells (i.e. a haloperidol-sensitive pathway and another, unclear, pathway). In

  15. Statistical properties of country risk ratings under oil price volatility: Evidence from selected oil-exporting countries

    International Nuclear Information System (INIS)

    Liu, Chang; Sun, Xiaolei; Chen, Jianming; Li, Jianping

    2016-01-01

    This paper focuses on the application of panel models for identification and analysis of influence of oil price volatility on statistical properties of country risk ratings which stem from uncertainty of macroeconomic fluctuations. Firstly, two statistical properties of country risk ratings, volatility clustering and asymmetrical revision were identified in a theoretical framework based on Cruces (2006). Secondly, considering the oil price volatility, numerical experiments were conducted based on extended models to test and verify specific properties of country risk ratings in selected oil-exporting countries. Empirical results suggest that properties of country risk remain comparatively steady despite oil price volatility. It is also found that the oil price volatility can obviously exaggerate the country risk volatility, as it happened during 2007–2009. Country clustering based on the properties of country risk ratings shows that the selected countries maintain a significant clustering tendency. These features are of great importance for estimating risk exposure of international trade and investments in oil export during extreme situations. - Highlights: •Relationship between oil price volatility and country risk is the focus. •An extended model based on Cruces (2006) is proposed. •Volatility clustering and asymmetrical revision of country risk ratings is explored. •Oil price volatility can obviously exaggerate properties of country risk volatility.

  16. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available Toggle navigation Test/Treatment Patient Type Screening/Wellness Disease/Condition Safety En Español More Info Images/Videos About Us News Physician ... of nuclear medicine imaging. The radioactive iodine uptake test (RAIU) is also known as a thyroid uptake. ...

  17. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available Toggle navigation Test/Treatment Patient Type Screening/Wellness Disease/Condition Safety En Español More Info Images/Videos About Us News Physician Resources Professions Site Index A-Z Thyroid Scan and Uptake Thyroid scan and uptake uses ...

  18. The disaccharide moiety of bleomycin facilitates uptake by cancer cells.

    Science.gov (United States)

    Schroeder, Benjamin R; Ghare, M Imran; Bhattacharya, Chandrabali; Paul, Rakesh; Yu, Zhiqiang; Zaleski, Paul A; Bozeman, Trevor C; Rishel, Michael J; Hecht, Sidney M

    2014-10-01

    The disaccharide moiety is responsible for the tumor cell targeting properties of bleomycin (BLM). While the aglycon (deglycobleomycin) mediates DNA cleavage in much the same fashion as bleomycin, it exhibits diminished cytotoxicity in comparison to BLM. These findings suggested that BLM might be modular in nature, composed of tumor-seeking and tumoricidal domains. To explore this possibility, BLM analogues were prepared in which the disaccharide moiety was attached to deglycobleomycin at novel positions, namely, via the threonine moiety or C-terminal substituent. The analogues were compared with BLM and deglycoBLM for DNA cleavage, cancer cell uptake, and cytotoxic activity. BLM is more potent than deglycoBLM in supercoiled plasmid DNA relaxation, while the analogue having the disaccharide on threonine was less active than deglycoBLM and the analogue containing the C-terminal disaccharide was slightly more potent. While having unexceptional DNA cleavage potencies, both glycosylated analogues were more cytotoxic to cultured DU145 prostate cancer cells than deglycoBLM. Dye-labeled conjugates of the cytotoxic BLM aglycons were used in imaging experiments to determine the extent of cell uptake. The rank order of internalization efficiencies was the same as their order of cytotoxicities toward DU145 cells. These findings establish a role for the BLM disaccharide in tumor targeting/uptake and suggest that the disaccharide moiety may be capable of delivering other cytotoxins to cancer cells. While the mechanism responsible for uptake of the BLM disaccharide selectively by tumor cells has not yet been established, data are presented which suggest that the metabolic shift to glycolysis in cancer cells may provide the vehicle for selective internalization.

  19. Influence of superplasticizers on the long-term properties of cement pastes and possible impact on radionuclide uptake in a cement-based repository for radioactive waste

    International Nuclear Information System (INIS)

    Wieland, E.; Lothenbach, B.; Glaus, M.A.; Thoenen, T.; Schwyn, B.

    2014-01-01

    Highlights: • We investigate the hydration of different cement mixes containing concrete admixtures. • The concentration of concrete admixtures decreases with time due to sorption on cement phases. • We observe no influence on the phase composition of cement paste and the ion composition of pore fluids. • Uptake of 63 Ni, 152 Eu and 228 Th by cement paste is not affected by the concrete admixtures. - Abstract: Cementitious materials will be used for the construction of the engineered barrier of the planned repositories for radioactive waste in Switzerland. Superplasticizers (SPs) are commonly used to improve the workability of concretes and, along with a set accelerator (Acc), to produce shotcrete. In this study the influence of a polycarboxylate- (PCE) and a polynaphthalene-sulphonate-based (PNS) SP on the hydration process, mineral composition and the sorption behaviour of metal cations has been investigated using an ordinary Portland cement (OPC), a low-alkali cement mix (LAC) consisting of CEM III-type cement and nanosilica, and a shotcrete-type cement mix (ESDRED) consisting of a CEM I-type cement and silica fume prepared in the presence of an alkali-free set accelerator. Both the PCE and PNS SP do not significantly influence the amount and quantity of hydrates formed during hydration. The concentration of both SPs decreased rapidly in the early stage of the hydration process for all cements due to sorption onto cement phases. After 28 days of hydration and longer, the concentration of the PNS SP in the pore fluids of all cements was generally lower than that of the PCE SP, indicating stronger uptake of the PNS SP. The formate present in the Acc sorbs only weakly onto the cement phases, which led to higher aqueous concentration of organics in the ESDRED cement than in OPC and LAC. Sorption experiments with 63 Ni, 152 Eu and 228 Th on a cation exchange resin indicate that, at concentrations above 0.1 g L −1 , the two SPs could reduce sorption of metal

  20. Spectral properties of X-ray selected narrow emission line galaxies

    Science.gov (United States)

    Romero-Colmenero, E.

    1998-03-01

    This thesis reports a study of the X-ray and optical properties of two samples of X-ray selected Narrow Emission Line Galaxies (NELGs), and their comparison with the properties of broad line Active Galactic Nuclei (AGN). One sample (18 NELGs) is drawn from the ROSAT International X-ray Optical Survey (RIXOS), the other (19 NELGs and 33 AGN) from the ROSAT UK Deep Survey. ROSAT multi-channel X-ray spectra have been extracted and fitted with power-law, bremsstrahlung and black body models for the brighter RIXOS sources. In most cases, power-law and bremsstrahlung models provide the best results. The average spectral energy index, alpha, of the RIXOS NELGs is 0.96 +/- 0.07, similar to that of AGN (alpha~1). For the fainter RIXOS NELGs, as well as for all the UK Deep Survey sources, counts in three spectral bands have been extracted and fitted with a power-law model, assuming the Galactic value for N_H. The brighter RIXOS sources demonstrated that the results obtained by these two different extraction and fitting procedures provide consistent results. Two average X-ray spectra, one for the NELGs and another for the AGN, were created from the UK Deep Survey sources. The power-law slope of the average NELG is alpha = 0.45 +/- 0.09, whilst that of the AGN is alpha = 0.96 +/- 0.03. ROSAT X-ray surveys have shown that the fractional surface density of NELGs increases with respect to AGN at faint fluxes (case for NELGs to be major contributors to the XRB at the fainter fluxes. The analysis of optical spectroscopy, obtained on La Palma and Hawaii, shows that NELGs form a very heterogeneous group, made up of a mixture of Seyfert 2, LINER and HII-region like galaxies. Seyfert 2 galaxies are found to possess in general the steepest X-ray slopes. Ways to explain this in the context of the unified model of AGN are discussed. The FWHM of some emission lines (Halpha, Hbeta, [NII]) in the NELGs appears to increase with steepening X-ray spectral slope. In the case of the Balmer lines

  1. Studies on the Catalytic Properties of Partially Purified Alkaline Proteases from Some Selected Microorganisms

    Directory of Open Access Journals (Sweden)

    Titilayo Olufunke Femi-Ola

    2012-09-01

    Full Text Available Aims: The research was done to study the conditions enhancing catalytic activities of alkaline proteases from Vibro sp., Lactobacillus brevis, Zymomonas sp., Athrobacter sp., Corynebacterium sp. and Bacillus subtilis.Methodology and Results: The proteolytic enzymes were purified in 2-step procedures involving ammonium sulphate precipitation and sephadex G-150 gel permeation chromatography. The upper and lower limits for the specific activities of proteases from the selected microorganisms were estimated at 20.63 and 47.51 units/mg protein with Zymomonas protease having the highest specific activity towards casein as its substrate and purification fold of 3.46, while that ofLactobacillus brevis protease was 8.06. The native molecular weights of these active proteins ranged from 30.4 to 45.7 kDa with Athrobacter sp. protease having the highest weight for its subunits. The proteolytic enzymes had optimum pH range of 8 to 10 and temperature range of 50 to 62 ºC accounting for the percentage relative activity range of 75 to 94% and 71 to 84 % respectively. The activities of Lactobacillus brevis and Bacillus subtilis proteases were maximum at pH 9 and 10 respectively. Lactobacillus brevis protease activity was maximum at temperature of 62 ºC, while beyond this value, a general thermal instability of these active proteins was observed. At above 70 ºC, the catalytic activities of Corynebacterium sp., Vibrio sp., Zymomonas sp. and Arthrobacter sp. proteases were progressively reduced over a period of 120 min of incubation, while Bacillus subtlis and Lactobacillus brevis proteases were relatively stable. Effect of metal ions was investigated on the catalytic activity of protease from the microorganisms. Lactobacillus brevis,Zymomonas sp., Arthrobacter sp., Corynebacterium sp. and Bacillus subtilis protease activities were strongly activated by metal ions such as Ca+2 and Mg+2. Enzyme activities were inhibited strongly by Cu2+ and Hg2+ but were not

  2. Selected properties of flue dust from the technologies on magnesite processing in Slovmag, inc. Lubeník

    Directory of Open Access Journals (Sweden)

    Bobro Milan

    1997-09-01

    Full Text Available The contribution deals with the properties of specimens obtained by sampling dust collectors in the selected production centres. The grain size distribution, morphological, mineral, and chemical properties were studied with the aim to determine their infuence on the environment. This research attests that the main component of studied flue dusts is MgO in two form: periclase and amorphous phase. The latter form is harmful. That is why continual observation of the quality of flue dust from the stand point of their exertion on the air and soil is needed.

  3. Out of Control: Attentional Selection for Orientation Is Thwarted by Properties of the Underlying Neural Mechanisms

    Science.gov (United States)

    Du, Feng; Abrams, Richard A.

    2012-01-01

    To avoid sensory overload, people are able to selectively attend to a particular color or direction of motion while ignoring irrelevant stimuli that differ from the desired one. We show here for the first time that it is also possible to selectively attend to a specific line orientation--but with an important caveat: orientations that are…

  4. Obscured AGN at z ~ 1 from the zCOSMOS-Bright Survey. I. Selection and optical properties of a [Ne v]-selected sample

    Science.gov (United States)

    Mignoli, M.; Vignali, C.; Gilli, R.; Comastri, A.; Zamorani, G.; Bolzonella, M.; Bongiorno, A.; Lamareille, F.; Nair, P.; Pozzetti, L.; Lilly, S. J.; Carollo, C. M.; Contini, T.; Kneib, J.-P.; Le Fèvre, O.; Mainieri, V.; Renzini, A.; Scodeggio, M.; Bardelli, S.; Caputi, K.; Cucciati, O.; de la Torre, S.; de Ravel, L.; Franzetti, P.; Garilli, B.; Iovino, A.; Kampczyk, P.; Knobel, C.; Kovač, K.; Le Borgne, J.-F.; Le Brun, V.; Maier, C.; Pellò, R.; Peng, Y.; Perez Montero, E.; Presotto, V.; Silverman, J. D.; Tanaka, M.; Tasca, L.; Tresse, L.; Vergani, D.; Zucca, E.; Bordoloi, R.; Cappi, A.; Cimatti, A.; Koekemoer, A. M.; McCracken, H. J.; Moresco, M.; Welikala, N.

    2013-08-01

    Aims: The application of multi-wavelength selection techniques is essential for obtaining a complete and unbiased census of active galactic nuclei (AGN). We present here a method for selecting z ~ 1 obscured AGN from optical spectroscopic surveys. Methods: A sample of 94 narrow-line AGN with 0.65 advantage of the large amount of data available in the COSMOS field, the properties of the [Ne v]-selected type 2 AGN were investigated, focusing on their host galaxies, X-ray emission, and optical line-flux ratios. Finally, a previously developed diagnostic, based on the X-ray-to-[Ne v] luminosity ratio, was exploited to search for the more heavily obscured AGN. Results: We found that [Ne v]-selected narrow-line AGN have Seyfert 2-like optical spectra, although their emission line ratios are diluted by a star-forming component. The ACS morphologies and stellar component in the optical spectra indicate a preference for our type 2 AGN to be hosted in early-type spirals with stellar masses greater than 109.5 - 10 M⊙, on average higher than those of the galaxy parent sample. The fraction of galaxies hosting [Ne v]-selected obscured AGN increases with the stellar mass, reaching a maximum of about 3% at ≈2 × 1011 M⊙. A comparison with other selection techniques at z ~ 1, namely the line-ratio diagnostics and X-ray detections, shows that the detection of the [Ne v] λ3426 line is an effective method for selecting AGN in the optical band, in particular the most heavily obscured ones, but cannot provide a complete census of type 2 AGN by itself. Finally, the high fraction of [Ne v]-selected type 2 AGN not detected in medium-deep (≈100-200 ks) Chandra observations (67%) is suggestive of the inclusion of Compton-thick (i.e., with NH > 1024 cm-2) sources in our sample. The presence of a population of heavily obscured AGN is corroborated by the X-ray-to-[Ne v] ratio; we estimated, by means of an X-ray stacking technique and simulations, that the Compton-thick fraction in our

  5. The orotate transporter oroP from Lactococcus lactis is required for orotate uptake and can be used both as a food-grade selection and counter-selection marker

    DEFF Research Database (Denmark)

    Defoor, Els Marie Celine; Martinussen, Jan

    The plasmid pDBORO conferred sensitivity of Lactococcus lactis towards 5´-Fluoroorotate. Moreover, by transformation, this plasmid was found to be essential for orotate dependent growth in a pyrimidine requiring strain. A single gene on pDBORO was required for growth on orotate, and was termed oro......P. Since the corresponding open reading frame, OroP showed the features of a membrane protein, OroP most likely is an orotate transporter. A number of strains like L. lactis and Bacillus subtilus have been shown to be unable to metabolize orotate. If the oroP gene was introduced into these strains......, they acquired the ability to utilize orotate. If the strains had a pyrimidine requirement, the oroP gene could function as a selectable marker when growing in the presence of orotate as sole pyrimidine source. In an otherwise resistant strain, oroP was shown to sensitize the strain towards the analog 5...

  6. Water-stability of soil aggregates in relation to selected properties

    International Nuclear Information System (INIS)

    Mbagwu, J.S.C.; Bazzoffi, P.; Unamba Oparah, I.

    1995-03-01

    The stability of soil aggregates in water is an important soil physical property for evaluating the potential of agricultural soils to erode and elucidating the mechanisms of soil erosion. In this study we used aggregates from 15 surface soil samples in Italy to evaluate the influence of intrinsic soil physical, chemical and mineralogical properties on aggregates stability (AS). The aim was to develop a model for predicting AS from a subset of these soil properties. The index of stability used is the mean-weight diameter of water-stable aggregates (MWD). The model developed with soil physical properties alone explained just 42% of variance in MWD and predicted AS in only 20% of test soils. The model developed with mineralogical properties alone explained 70% of variance in MWD and predicted AS in 60% of the test soils. The chemical properties - based model explained 90% of variance in MWD and predicted AS in 80% of the test soils. The best-fit model was developed with soil properties from the physical, chemical and mineralogical subsets. It explained 98% of variance in MWD and predicted AS in 100% of the test soils. This model shows that the most important soil properties which influence the AS of these soils include ratio of total sand to clay, concentrations of iron oxide, magnesium oxide, organic matter, silica/alumina ratio, chlorite, feldspar and muscovite. This indicates that fairly good estimates of the relative stability of these aggregates in water and hence of their potential to erode, requires a knowledge of the physico-chemical and mineralogical properties. (author). 40 refs, 4 tabs

  7. Influence of sand base preparation on properties of chromite moulding sands with sodium silicate hardened with selected methods

    Directory of Open Access Journals (Sweden)

    Stachowicz M.

    2017-03-01

    Full Text Available The paper presents a research on the relation between thermal preparation of chromite sand base of moulding sands containing sodium silicate, hardened with selected physical and chemical methods, and structure of the created bonding bridges. Test specimens were prepared of chromite sand - fresh or baked at 950°C for 10 or 24 hours - mixed with 0.5 wt.% of the selected non-modified inorganic binder and, after forming, were hardened with CO2 or liquid esters, dried traditionally or heated with microwaves at 2.45 GHz. It was shown on the grounds of SEM observations that the time of baking the base sand and the hardening method significantly affect structure of the bonding bridges and are correlated with mechanical properties of the moulding sands. It was found that hardening chromite-based moulding mixtures with physical methods is much more favourable than hardening with chemical methods, guaranteeing also more than ten times higher mechanical properties.

  8. The eff ect of addition of selected vegetables on the microbiological, textural and fl avour profi le properties of yoghurts

    OpenAIRE

    Dorota Najgebauer-Lejko; Małgorzata Tabaszewska; Tadeusz Grega

    2015-01-01

    Background. Vegetables, apart from having high nutritional value, also contain considerable amounts of dietary fi bre and other components, which may affect physico-chemical properties of fermented milks, e.g. viscosity, texture, susceptibility to syneresis, fl avour profi le etc. The present work was established to study the effect of selected vegetables addition on the rheological, textural, microbiological and fl avour profi le parameters of yoghurts. Material and methods. The vegetabl...

  9. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... information about your thyroid’s size, shape, position and function that is often unattainable using other imaging procedures. ... thyroid uptake. It is a measurement of thyroid function, but does not involve imaging. Nuclear medicine is ...

  10. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... which are encased in metal and plastic and most often shaped like a box, attached to a ... will I experience during and after the procedure? Most thyroid scan and thyroid uptake procedures are painless. ...

  11. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... eat for several hours before your exam because eating can affect the accuracy of the uptake measurement. ... often unattainable using other imaging procedures. For many diseases, nuclear medicine scans yield the most useful information ...

  12. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... A thyroid scan is a type of nuclear medicine imaging. The radioactive iodine uptake test (RAIU) is ... thyroid function, but does not involve imaging. Nuclear medicine is a branch of medical imaging that uses ...

  13. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... Because nuclear medicine procedures are able to pinpoint molecular activity within the body, they offer the potential ... or imaging device that produces pictures and provides molecular information. The thyroid scan and thyroid uptake provide ...

  14. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... Actual scanning time for each thyroid uptake is five minutes or less. top of page What will ... diagnostic procedures have been used for more than five decades, and there are no known long-term ...

  15. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... top of page Additional Information and Resources RTAnswers.org Radiation Therapy for Head and Neck Cancer top ... Scan and Uptake Sponsored by Please note RadiologyInfo.org is not a medical facility. Please contact your ...

  16. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... When radiotracer is taken by mouth, in either liquid or capsule form, it is typically swallowed up ... radioactive iodine (I-123 or I-131) in liquid or capsule form to swallow. The thyroid uptake ...

  17. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... RAIU) is also known as a thyroid uptake. It is a measurement of thyroid function, but does ... they offer the potential to identify disease in its earliest stages as well as a patient’s immediate ...

  18. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... for several hours before your exam because eating can affect the accuracy of the uptake measurement. Jewelry ... small hand-held device resembling a microphone that can detect and measure the amount of the radiotracer ...

  19. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... of page What will I experience during and after the procedure? Most thyroid scan and thyroid uptake ... you otherwise, you may resume your normal activities after your nuclear medicine scan. If any special instructions ...

  20. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... scan and thyroid uptake provide information about the structure and function of the thyroid. The thyroid is ... computer, create pictures offering details on both the structure and function of organs and tissues in your ...

  1. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... eat for several hours before your exam because eating can affect the accuracy of the uptake measurement. ... its radioactivity over time. It may also pass out of your body through your urine or stool ...

  2. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... procedures within the last two months that used iodine-based contrast material. Your doctor will instruct you ... a type of nuclear medicine imaging. The radioactive iodine uptake test (RAIU) is also known as a ...

  3. Sample selection, preparation methods, and the apparent tensile properties of silkworm (B. mori) cocoon silk.

    Science.gov (United States)

    Reed, Emily J; Bianchini, Lindsay L; Viney, Christopher

    2012-06-01

    Reported literature values of the tensile properties of natural silk cover a wide range. While much of this inconsistency is the result of variability that is intrinsic to silk, some is also a consequence of differences in the way that silk is prepared for tensile tests. Here we explore how measured mechanical properties of Bombyx mori cocoon silk are affected by two intrinsic factors (the location from which the silk is collected within the cocoon, and the color of the silk), and two extrinsic factors (the storage conditions prior to testing, and different styles of reeling the fiber). We find that extrinsic and therefore controllable factors can affect the properties more than the intrinsic ones studied. Our results suggest that enhanced inter-laboratory collaborations, that lead to standardized sample collection, handling, and storage protocols prior to mechanical testing, would help to decrease unnecessary (and complicating) variation in reported tensile properties. Copyright © 2011 Wiley Periodicals, Inc.

  4. Complex approach mechanical properties and formability assessment of selected deep-drawing steels

    Directory of Open Access Journals (Sweden)

    J. Štaba

    2009-07-01

    Full Text Available The paper analyses the properties of deep-drawing sheets of three grades (Re = 320 to 475 MPa, surface-treated with hot-dip galvanizing, made of microalloyed steels. Deformation properties are assessed using tensile tests, technological Erichsen or cupping tests. These characteristics, as well as the behaviour of the surface layer, are also investigated under dynamic conditions (modified Erichsen test using a drop tester, or using flat bending fatigue tests. Using microscopic analysis the deformation properties of the surface layer are evaluated. The results show the compactness of the surface layer, high deformation characteristics, as well as fatigue properties of the investigated deep-drawing materials, suitable for application in the automotive industry.

  5. Vapor pressures and thermophysical properties of selected hexenols and recommended vapor pressure for hexan-1-ol

    Czech Academy of Sciences Publication Activity Database

    Štejfa, V.; Fulem, Michal; Růžička, K.; Matějka, P.

    2015-01-01

    Roč. 402, Sep (2015), 18-29 ISSN 0378-3812 Institutional support: RVO:68378271 Keywords : alcohols * vapor pressure * heat capacity * ideal - gas thermodynamic properties * vaporization enthalpy Subject RIV: BJ - Thermodynamics Impact factor: 1.846, year: 2015

  6. The analysis of the mechanical properties of F75 Co-Cr alloy for use in selective laser melting (SLM manufacturing of removable partial dentures (RPD

    Directory of Open Access Journals (Sweden)

    D. Jevremovic

    2012-04-01

    Full Text Available The presented work discusses the applicability of the selective laser melting technique (SLM in manufacture of removable partial denture (RPD frameworks with the emphasis on material properties. The paper presents initial results of a conducted test of the mechanical properties of the F75 Co-Cr dental alloy used with selective laser melting.

  7. Complex approach mechanical properties and formability assessment of selected deep-drawing steels

    OpenAIRE

    J. Štaba; M. Buršák

    2009-01-01

    The paper analyses the properties of deep-drawing sheets of three grades (Re = 320 to 475 MPa), surface-treated with hot-dip galvanizing, made of microalloyed steels. Deformation properties are assessed using tensile tests, technological Erichsen or cupping tests. These characteristics, as well as the behaviour of the surface layer, are also investigated under dynamic conditions (modified Erichsen test using a drop tester), or using flat bending fatigue tests. Using microscopic analysis the d...

  8. Friction Surface Treatment Selection: Aggregate Properties, Surface Characteristics, Alternative Treatments, and Safety Effects

    Science.gov (United States)

    2017-07-01

    This study aimed to evaluate the long term performance of the selected surface friction treatments, including high friction surface treatment (HFST) using calcined bauxite and steel slag, and conventional friction surfacing, in particular pavement pr...

  9. Quasi continuum vibrational of molecules and isotopic selectivity properties induced by collisions

    International Nuclear Information System (INIS)

    Angelie, Christian

    1990-01-01

    This research thesis proposes an overview of knowledge on vibrationally highly excited states of molecules. The author shows that the statistic quasi-continuum formed by these states is preceded by a quasi continuum of weak transitions with a lower energy, and that these transitions remain structured and very narrow up to the dissociation energy and beyond. Collisions between molecules excited in their quasi continuum are then studied. The author particularly analyses a new phenomenon of isotopic selectivity which is important for the dissociation of a molecule colliding another molecule. It appears that this selectivity regarding selectivity is due to a selectivity of transferred energy which paradoxically increases with the molecule vibrational content because of a resonance phenomenon of energies transferred by dipole-dipole interaction [fr

  10. High-power, cladding-pumped all-fiber laser with selective transverse mode generation property.

    Science.gov (United States)

    Li, Lei; Wang, Meng; Liu, Tong; Leng, Jinyong; Zhou, Pu; Chen, Jinbao

    2017-06-10

    We demonstrate, to the best of our knowledge, the first cladding-pumped all-fiber oscillator configuration with selective transverse mode generation based on a mode-selective fiber Bragg grating pair. Operating in the second-order (LP 11 ) mode, maximum output power of 4.2 W is obtained with slope efficiency of about 38%. This is the highest reported output power of single higher-order transverse mode generation in an all-fiber configuration. The intensity distribution profile and spectral evolution have also been investigated in this paper. Our work suggests the potential of realizing higher power with selective transverse mode operation based on a mode-selective fiber Bragg grating pair.

  11. Optical properties of selectively absorbing C/NiO nanocomposite coatings

    CSIR Research Space (South Africa)

    Roro, Kittessa T

    2010-12-01

    Full Text Available Nanocomposite thin films are widely used for solar thermal applications. Using carbon nanoparticle containing metal oxide as a spectrally selective solar absorber coating has grown significantly in recent years. Recently, Katumba et al. have...

  12. Variations in Carabidae assemblages across the farmland habitats in relation to selected environmental variables including soil properties

    Directory of Open Access Journals (Sweden)

    Beáta Baranová

    2018-03-01

    Full Text Available The variations in ground beetles (Coleoptera: Carabidae assemblages across the three types of farmland habitats, arable land, meadows and woody vegetation were studied in relation to vegetation cover structure, intensity of agrotechnical interventions and selected soil properties. Material was pitfall trapped in 2010 and 2011 on twelve sites of the agricultural landscape in the Prešov town and its near vicinity, Eastern Slovakia. A total of 14,763 ground beetle individuals were entrapped. Material collection resulted into 92 Carabidae species, with the following six species dominating: Poecilus cupreus, Pterostichus melanarius, Pseudoophonus rufipes, Brachinus crepitans, Anchomenus dorsalis and Poecilus versicolor. Studied habitats differed significantly in the number of entrapped individuals, activity abundance as well as representation of the carabids according to their habitat preferences and ability to fly. However, no significant distinction was observed in the diversity, evenness neither dominance. The most significant environmental variables affecting Carabidae assemblages species variability were soil moisture and herb layer 0-20 cm. Another best variables selected by the forward selection were intensity of agrotechnical interventions, humus content and shrub vegetation. The other from selected soil properties seem to have just secondary meaning for the adult carabids. Environmental variables have the strongest effect on the habitat specialists, whereas ground beetles without special requirements to the habitat quality seem to be affected by the studied environmental variables just little.

  13. Ultraselective Carbon Molecular Sieve Membranes with Tailored Synergistic Sorption Selective Properties.

    Science.gov (United States)

    Zhang, Chen; Koros, William J

    2017-09-01

    Membrane-based separations can reduce the energy consumption and the CO 2 footprint of large-scale fluid separations, which are traditionally practiced by energy-intensive thermally driven processes. Here, a new type of membrane structure based on nanoporous carbon is reported, which, according to this study, is best referred to as carbon/carbon mixed-matrix (CCMM) membranes. The CCMM membranes are formed by high-temperature (up to 900 °C) pyrolysis of polyimide precursor hollow-fiber membranes. Unprecedentedly high permselectivities are seen in CCMM membranes for CO 2 /CH 4 , N 2 /CH 4 , He/CH 4 , and H 2 /CH 4 separations. Analysis of permeation data suggests that the ultrahigh selectivities result from substantially increased sorption selectivities, which is hypothetically owing to the formation of ultraselective micropores that selectively exclude the bulkier CH 4 molecules. With tunable sorption selectivities, the CCMM membranes outperform flexible polymer membranes and traditional rigid molecular-sieve membranes. The capability to increase sorption selectivities is a powerful tool to leverage diffusion selectivities, and has opened the door to many challenging and economically important fluid separations that require ultrafine differentiation of closely sized molecules. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Modulation of liver mitochondrial NOS is implicated in thyroid-dependent regulation of O(2) uptake.

    Science.gov (United States)

    Carreras, M C; Peralta, J G; Converso, D P; Finocchietto, P V; Rebagliati, I; Zaninovich, A A; Poderoso, J J

    2001-12-01

    Changes in O(2) uptake at different thyroid status have been explained on the basis of the modulation of mitochondrial enzymes and membrane biophysical properties. Regarding the nitric oxide (NO) effects, we tested whether liver mitochondrial nitric oxide synthase (mtNOS) participates in the modulation of O(2) uptake in thyroid disorders. Wistar rats were inoculated with 400 microCi (131)I (hypothyroid group), 20 microg thyroxine (T(4))/100 g body wt administered daily for 2 wk (hyperthyroid group) or vehicle (control). Basal metabolic rate, mitochondrial function, and mtNOS activity were analyzed. Systemic and liver mitochondrial O(2) uptake and cytochrome oxidase activity were lower in hypothyroid rats with respect to controls; mitochondrial parameters were further decreased by L-arginine (-42 and -34%, P activity (260%) were selectively increased in hypothyroidism and reverted by hormone replacement without changes in other nitric oxide isoforms. Moreover, mtNOS activity correlated with serum 3,5,3'-triiodothyronine (T(3)) and O(2) uptake. Increased mtNOS activity was also observed in skeletal muscle mitochondria from hypothyroid rats. Therefore, we suggest that modulation of mtNOS is a substantial part of thyroid effects on mitochondrial O(2) uptake.

  15. Selected Physical Properties of Andisols under Different Land Use Condition in Gunung Kerinci Subdistrict, Jambi

    Directory of Open Access Journals (Sweden)

    Endriani

    2010-05-01

    Full Text Available Objective of the research was to study the effect of different land use at some land slopecondition on some physical properties of Andisols in Gunung Kerinci Subdistrict, Jambi.. The research was conductusing field survey and purposive random sampling methods to collect soil. The land use which was using in this studywere: forest, cultivation, cinnamon, and coffee plantation, while land slope level weres: 3-8%, 8-15%, 15-25 %, and> 25%. The results showed that among land use types, the rank of soil physical properties, such as: soil organicmatter, bulk density, porosity, percentage of agregation, stability of agregate, pore distribution and permeability werein order of : forest > cultivation > cinnamon > coffee. Land conversion from forest to agricultural land causeddecreasing in the soil physical properties. The higher level of land slope caused the decreasing of soil physicalproperties at all type of land use.

  16. Corrosive effect of environmental change on selected properties of polymer composites

    Science.gov (United States)

    Markovičová, L.; Zatkalíková, V.

    2017-11-01

    The development of composite materials and the related design and manufacturing technologies is one of the most important advances in the history of materials. Composites are multifunctional materials having unprecedented mechanical and physical properties that can be tailored to meet the requirements of a particular application. Ageing is also important and it is defined as the process of deterioration of engineering materials resulting from the combined effects of atmospheric radiation, heat, oxygen, water, micro-organisms and other atmospheric factors. The present article deals with monitoring the changes in the mechanical properties of composites with polymer matrix. The composite was formed from the PA matrix and glass fibers (GF). The composite contains 10, 20 and 30 % of glass fibers. The mechanical properties were evaluated on samples of the composite before and after UV radiation on the sample. Light microscopy was evaluated distribution of glass fibers in the polymer matrix and the presence of cracks caused by UV radiation.

  17. Normal spectral emissivity of selected liquid metals and improved thermophysical properties

    International Nuclear Information System (INIS)

    Pottlacher, G.; Seifter, A.

    2001-01-01

    Full Text: Emissivity measurements on several liquid metals up to temperatures of 6000 K have been successfully established by linking a laser polarimetry technique to our well-known method for performing high speed measurements of thermophysical properties on liquid metal samples during microsecond pulse-heating experiments. Thermophysical properties measured with our experimental setup include temperature dependencies of heat capacity, enthalpy, electrical resistivity, density, thermal diffusivity and thermal conductivity up to the end of the stable liquid phase. During grant P12775-PHY additionally to the above listened properties the measurement of the change of the polarization of laser light reflected from the surface during pulse heating was enabled and thus now the temperature dependence of spectral emissivity at 684.5 nm by methods of ellipsometry is derived also. Several liquid metals and alloys have been investigated within this grant and a review of the data obtained will be given here. (author)

  18. Synthesis and characterization of a new activated carbon supported ammonium molybdophosphate composite and its cesium-selective adsorption properties

    International Nuclear Information System (INIS)

    Feng Miao; Wang Li; Zhao Yongsheng; Liu Chunxia; Chen Zhen; Yan Liang; Tian Gan; Wang Hang; Li Shoujian

    2010-01-01

    A new Cs + adsorbent, activated carbon loaded ammonium molybdophosphate (AMP-AC) was prepared by repeating batch reaction of H 3 PO 4 and (NH 4 ) 6 Mo 7 O 24 . The surface of the activated carbon particles was coated with AMP microcrystals through a controlled crystallization process. The X-ray diffraction (XRD) analysis identified the AMP loaded on AC with the formula of (NH 4 ) 3 PO 4 (MoO 3 ) 12 .4H 2 O. Scanning electron microscope images demonstrated that the fine AMP crystals was successfully immobilized and uniformly distributed on the porous carbon substrate. The effects of medium acidity, contact time, temperature and competing ions on Cs + uptake by the composite were investigated. The results show that the as-prepared adsorbent keeps high selectivity and adsorption capacity (∝0.75 mmol/g) for Cs + in acidic feed solution (0.1 M HNO 3 ). even in the presence of plentiful competing cations. Na + , Zn 2+ , Sr 2+ , Cr 3+ and La 3+ , while activated carbon itself has no specific affinity for Cs + . The adsorption process could be described by Langmuir adsorption equations. There is no significant difference (9.4%) on Cs + adsorption by the composite during system temperature changing from 298 to 348 K. (orig.)

  19. Uranium uptake of Vetiveria zizanioides (L.) Nash

    International Nuclear Information System (INIS)

    Luu Viet Hung; Maslov, O.D.; Trinh Thi Thu My; Phung Khac Nam Ho; Dang Duc Nhan

    2010-01-01

    Uranium uptake of vetiver grass (Vetiveria zizanioides (L.) Nash) from Eutric Fluvisols (AK), Albic Acrisols (BG), Dystric Fluvisols (HP) and Ferralic Acrisols (TC) in northern Vietnam is assessed. The soils were mixed with aqueous solution of uranyl nitrate to make soils contaminated with uranium at 0, 50, 100, 250 mg/kg before planting the grass. The efficiency of uranium uptake by the grass was assessed based on the soil-to-plant transfer factor (TF U , kg·kg -1 ). It was found that the TF U values are dependent upon the soils properties. CEC facilitates the uptake and the increased soil pH could reduce the uptake and translocation of uranium in the plant. Organic matter content, as well as iron and potassium, inhibits the uranium uptake of the grass. It was revealed that the lower fertile soil, the higher uranium uptake. The translocation of uranium in root for all the soil types studied is almost higher than that in its shoot. It seems that vetiver grass could potentially be used for the purpose of phytoremediation of soils contaminated with uranium

  20. Dependence of FDG uptake on tumor microenvironment

    International Nuclear Information System (INIS)

    Pugachev, Andrei; Ruan, Shutian; Carlin, Sean; Larson, Steven M.; Campa, Jose; Ling, C. Clifton; Humm, John L.

    2005-01-01

    Purpose: To investigate the factors affecting the 18 F-fluorodeoxyglucose ( 18 F-FDG) uptake in tumors at a microscopic level, by correlating it with tumor hypoxia, cellular proliferation, and blood perfusion. Methods and Materials: Nude mice bearing Dunning prostate tumors (R3327-AT) were injected with 18 F-FDG and pimonidazole, bromodeoxyuridine, and, 1 min before sacrifice, with Hoechst 33342. Selected tumor sections were imaged by phosphor plate autoradiography, while adjacent sections were used to obtain the images of the spatial distribution of Hoechst 33342, pimonidazole, and bromodeoxyuridine. The images were co-registered and analyzed on a pixel-by-pixel basis. Results: Statistical analysis of the data obtained from these tumors demonstrated that 18 F-FDG uptake was positively correlated with pimonidazole staining intensity in each data set studied. Correlation of FDG uptake with bromodeoxyuridine staining intensity was always negative. In addition, FDG uptake was always negatively correlated with the staining intensity of Hoechst 33342. Conclusions: For the Dunning prostate tumors studied, FDG uptake was always positively correlated with hypoxia and negatively correlated with both cellular proliferation and blood flow. Therefore, for the tumor model studied, higher FDG uptake is indicative of tumor hypoxia, but neither blood flow nor cellular proliferation

  1. Alteration of properties of rock during their selection by shooting core lifter

    Energy Technology Data Exchange (ETDEWEB)

    Malinin, V F

    1969-01-01

    During the process of intrusion of the core lifter into rock, splitting and dislocation of the granules and crystals which compose it occur. In the core lifters, single small nondisintegrated fragments are sometimes encountered. Data on comparison of porosity of crushed cores and rock from which they were selected indicate increase in porosity and penetration of the filtrate of the drilling solution during the process of coring. The determined residual oil saturation of the core is different from the residual oil saturation of the rock from which they were selected. The permeability of cores of rock with high porosity is altered.

  2. Binding proteins enhance specific uptake rate by increasing the substrate-transporter encounter rate.

    Science.gov (United States)

    Bosdriesz, Evert; Magnúsdóttir, Stefanía; Bruggeman, Frank J; Teusink, Bas; Molenaar, Douwe

    2015-06-01

    Microorganisms rely on binding-protein assisted, active transport systems to scavenge for scarce nutrients. Several advantages of using binding proteins in such uptake systems have been proposed. However, a systematic, rigorous and quantitative analysis of the function of binding proteins is lacking. By combining knowledge of selection pressure and physiochemical constraints, we derive kinetic, thermodynamic, and stoichiometric properties of binding-protein dependent transport systems that enable a maximal import activity per amount of transporter. Under the hypothesis that this maximal specific activity of the transport complex is the selection objective, binding protein concentrations should exceed the concentration of both the scarce nutrient and the transporter. This increases the encounter rate of transporter with loaded binding protein at low substrate concentrations, thereby enhancing the affinity and specific uptake rate. These predictions are experimentally testable, and a number of observations confirm them. © 2015 FEBS.

  3. Selected properties of particleboard panels manufactured from rice straws of different geometries

    Science.gov (United States)

    Xianjun Li; Zhiyong Cai; Jerrold E. Winandy; Altaf H. Basta

    2010-01-01

    The objective is to evaluate the primary mechanical and physical properties of particleboard made from hammer-milled rice straw particles of six different categories and two types of resins. The results show the performance of straw particleboards is highly dependent upon the straw particle size controlled by the opening size of the perforated plate inside the hammer-...

  4. The effect of chain length and lipid phase transitions on the selective permeability properties of liposomes

    NARCIS (Netherlands)

    Blok, M.C.; Neut-Kok, E.C.M. van der; Deenen, L.L.M. van; Gier, J. de

    1975-01-01

    This paper describes experiments showing the importance of the fatty acid chain length on the barrier properties of liposomal bilayers, prepared from saturated lecithins, under conditions of lateral phase separation. 1. 1.|Above the gel to liquid crystalline phase transition temperature,

  5. Influence of Polylactide Modification with Blowing Agents on Selected Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Aneta Tor-Świątek

    2017-12-01

    Full Text Available Article presents research of modification of PLA with four types of chemical blowing agents with a different decomposition characteristic. The modification was done both cellular extrusion and injection molding processes. Obtained results shows that dosing blowing agents have the influence on mechanical properties and structure morphology of PLA. The differences in obtained results are also visible and significant between cellular processes.

  6. Selection of Prediction Methods for Thermophysical Properties for Process Modeling and Product Design of Biodiesel Manufacturing

    DEFF Research Database (Denmark)

    Su, Yung-Chieh; Liu, Y. A.; Díaz Tovar, Carlos Axel

    2011-01-01

    To optimize biodiesel manufacturing, many reported studies have built simulation models to quantify the relationship between operating conditions and process performance. For mass and energy balance simulations, it is essential to know the four fundamental thermophysical properties of the feed oil...... prediction methods on our group Web site (www.design.che.vt.edu) for the reader to download without charge....

  7. Effects of selected factors on rheological and textural properties of probiotic yoghurt

    Directory of Open Access Journals (Sweden)

    Jovana Glušac

    2011-03-01

    Full Text Available The aim of this work was to study the influence of inulin (1 %, combination of inulin (1 % and acacia honey (4 %, heat treatment of milk, and storage time on the rheological and textural properties of probiotic yoghurt. Rheological properties were assessed trough viscosity, syneresis and texture (firmness, consistency, cohesiveness and index of viscosity. Yoghurt was prepared from milk (1,5 % fat with added inulin (1% before heat treatment at 85 °C for 20 min or 95 °C for 10 min. After cooling to 55 °C honey (4 % was added. Samples were inoculated using probiotic starter culture (70 % w/w Streptococcus thermophilus, 10 % w/w Lactobacillus bulgaricus, 10 % w/w Lactobacillus acidophilus, 10 % w/w Bifidobacterium ssp.. Yoghurt samples were held on +5 °C during 21 days. Measurements of pH value, lactic acid, viscosity, syneresis, and textural properties were done after 1, 7, 14 and 21 days of storage. The results of this study show that honey addition significantly decreased fermentation time compared to fermentation time of control samples or samples containing inulin. Furthermore, addition of honey and inulin to milk caused significant lower syneresis (p<0,05 during storage time, while there was no significant influence on viscosity and texture of final product. The applied heat treatment of milk had no significant influence on rheological properties of probiotic yoghurt.

  8. IAU 2015 Resolution B3 on Recommended Nominal Conversion Constants for Selected Solar and Planetary Properties

    DEFF Research Database (Denmark)

    Mamajek, E. E.; Prsa, A.; Torres, G.

    2015-01-01

    Astronomers commonly quote the properties of celestial objects in units of parameters for the Sun, Jupiter, or the Earth. The resolution presented here was proposed by the IAU Inter-Division Working Group on Nominal Units for Stellar and Planetary Astronomy and passed by the XXIXth IAU General As...

  9. Combinational Effect of Cell Adhesion Biomolecules and Their Immobilized Polymer Property to Enhance Cell-Selective Adhesion

    Directory of Open Access Journals (Sweden)

    Rio Kurimoto

    2016-01-01

    Full Text Available Although surface immobilization of medical devices with bioactive molecules is one of the most widely used strategies to improve biocompatibility, the physicochemical properties of the biomaterials significantly impact the activity of the immobilized molecules. Herein we investigate the combinational effects of cell-selective biomolecules and the hydrophobicity/hydrophilicity of the polymeric substrate on selective adhesion of endothelial cells (ECs, fibroblasts (FBs, and smooth muscle cells (SMCs. To control the polymeric substrate, biomolecules are immobilized on thermoresponsive poly(N-isopropylacrylamide-co-2-carboxyisopropylacrylamide (poly(NIPAAm-co-CIPAAm-grafted glass surfaces. By switching the molecular conformation of the biomolecule-immobilized polymers, the cell-selective adhesion performances are evaluated. In case of RGDS (Arg-Gly-Asp-Ser peptide-immobilized surfaces, all cell types adhere well regardless of the surface hydrophobicity. On the other hand, a tri-Arg-immobilized surface exhibits FB-selectivity when the surface is hydrophilic. Additionally, a tri-Ile-immobilized surface exhibits EC-selective cell adhesion when the surface is hydrophobic. We believe that the proposed concept, which is used to investigate the biomolecule-immobilized surface combination, is important to produce new biomaterials, which are highly demanded for medical implants and tissue engineering.

  10. A novel coping metal material CoCrCu alloy fabricated by selective laser melting with antimicrobial and antibiofilm properties

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Ling [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Memarzadeh, Kaveh [Institute of Dentistry, Barts and The London School of Medicine & Dentistry, Queen Mary University of London, Newark Street, London E1 2AT (United Kingdom); Zhang, Shuyuan; Sun, Ziqing; Yang, Chunguang [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Ren, Guogang [University of Hertfordshire, Hatfield AL10 9AB (United Kingdom); Allaker, Robert P., E-mail: r.p.allaker@qmul.ac.uk [Institute of Dentistry, Barts and The London School of Medicine & Dentistry, Queen Mary University of London, Newark Street, London E1 2AT (United Kingdom); Yang, Ke, E-mail: kyang@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China)

    2016-10-01

    Objective: The aim of this study was to fabricate a novel coping metal CoCrCu alloy using a selective laser melting (SLM) technique with antimicrobial and antibiofilm activities and to investigate its microstructure, mechanical properties, corrosion resistance and biocompatibility. Methods: Novel CoCrCu alloy was fabricated using SLM from a mixture of commercial CoCr based alloy and elemental Cu powders. SLM CoCr without Cu served as control. Antibacterial activity was analyzed using standard antimicrobial tests, and antibiofilm properties were investigated using confocal laser scanning microscope. Cu distribution and microstructure were determined using scanning electron microscope, optical microscopy and X-ray diffraction. Corrosion resistance was evaluated by potential dynamic polarization and biocompatibility measured using an MTT assay. Results: SLM CoCrCu alloys were found to be bactericidal and able to inhibit biofilm formation. Other factors such as microstructure, mechanical properties, corrosion resistance and biocompatibility were similar to those of SLM CoCr alloys. Significance: The addition of appropriate amounts of Cu not only maintains normal beneficial properties of CoCr based alloys, but also provides SLM CoCrCu alloys with excellent antibacterial and antibiofilm capabilities. This material has the potential to be used as a coping metal for dental applications. - Highlights: • Novel CoCrCu alloys were fabricated by using selective laser melting (SLM). • SLM CoCrCu alloys showed satisfied antimicrobial and antibiofilm activities. • SLM CoCrCu alloys have no cytotoxic effect on normal cells. • Other properties of SLM CoCrCu alloys were similar to SLM CoCr alloys. • SLM CoCrCu alloys have the potential to be used as coping metals.

  11. A novel coping metal material CoCrCu alloy fabricated by selective laser melting with antimicrobial and antibiofilm properties

    International Nuclear Information System (INIS)

    Ren, Ling; Memarzadeh, Kaveh; Zhang, Shuyuan; Sun, Ziqing; Yang, Chunguang; Ren, Guogang; Allaker, Robert P.; Yang, Ke

    2016-01-01

    Objective: The aim of this study was to fabricate a novel coping metal CoCrCu alloy using a selective laser melting (SLM) technique with antimicrobial and antibiofilm activities and to investigate its microstructure, mechanical properties, corrosion resistance and biocompatibility. Methods: Novel CoCrCu alloy was fabricated using SLM from a mixture of commercial CoCr based alloy and elemental Cu powders. SLM CoCr without Cu served as control. Antibacterial activity was analyzed using standard antimicrobial tests, and antibiofilm properties were investigated using confocal laser scanning microscope. Cu distribution and microstructure were determined using scanning electron microscope, optical microscopy and X-ray diffraction. Corrosion resistance was evaluated by potential dynamic polarization and biocompatibility measured using an MTT assay. Results: SLM CoCrCu alloys were found to be bactericidal and able to inhibit biofilm formation. Other factors such as microstructure, mechanical properties, corrosion resistance and biocompatibility were similar to those of SLM CoCr alloys. Significance: The addition of appropriate amounts of Cu not only maintains normal beneficial properties of CoCr based alloys, but also provides SLM CoCrCu alloys with excellent antibacterial and antibiofilm capabilities. This material has the potential to be used as a coping metal for dental applications. - Highlights: • Novel CoCrCu alloys were fabricated by using selective laser melting (SLM). • SLM CoCrCu alloys showed satisfied antimicrobial and antibiofilm activities. • SLM CoCrCu alloys have no cytotoxic effect on normal cells. • Other properties of SLM CoCrCu alloys were similar to SLM CoCr alloys. • SLM CoCrCu alloys have the potential to be used as coping metals.

  12. Tuning the dielectric properties of polystyrene/poly(vinylidene fluoride) blends by selectively localizing carbon black nanoparticles.

    Science.gov (United States)

    Zhao, Xiaodong; Zhao, Jun; Cao, Jian-Ping; Wang, Xiaoyan; Chen, Min; Dang, Zhi-Min

    2013-02-28

    In this work, the dielectric properties of immiscible polystyrene (PS)/poly(vinylidene fluoride) (PVDF) blends are tuned by selectively localizing carbon black (CB) nanoparticles in different phases. The PS/PVDF blends have a wide window of cocontinuity (ca. 30-80 vol % in terms of the volume fraction of PS component (v(PS))). The selective localization of CB nanoparticles is achieved by using the masterbatch process during melt mixing. For the volume ratio PS/PVDF 1/1 and the volume fraction of CB nanoparticles (v(CB)) below but close to the percolation threshold (v(c)(CB)), the selective localization of CB nanoparticles in PVDF phase produces higher dielectric constant (ε) than that in PS phase, whereas the ε of the ternary mixtures without selective localization of fillers is in the middle. For the volume ratios PS/PVDF 1/2 and 2/1, the selective location of CB nanoparticles in different phases can be used to easily tune the system from conductive to insulating or inverse, which might have potential applications in industry. The fillers are found to be "fixed" in the masterbatch of PS or PVDF component and there is no migration of the fillers to another phase occurring during the further mixing process for the mixing time up to 30 min. Furthermore, the addition of CB nanoparticles to the polymer matrix is found to induce the brittle-ductile transition in the system and increase the compatibility between the immiscible PS and PVDF components, which should benefit the mechanical properties.

  13. Optimisation of optical absorption properties of spectrally selective C-NiO composite coatings

    CSIR Research Space (South Africa)

    Tile, N

    2011-05-01

    Full Text Available and expensive. Carbon in Nickel Oxide (C-NiO) composite material has been found to have a very good spectral selectivity1,2. Moreover this material has a potential of low cost large scale fabrication since it can be fabricated by a simple sol-gel technique...

  14. Differentiability properties of the efficient (u,q2)-set in the Markowitz portfolio selection method

    NARCIS (Netherlands)

    Kriens, J.; Strijbosch, L.W.G.; Vörös, J.

    1994-01-01

    The set of efficient (Rho2)-combinations in the (Rho2)-plane of the Markowitz portfolio selection method consists of a series of strictly convex parabola. In the transition points from one parabola to the next one, the curve may be indifferentiable. The article gives necessary and sufficient

  15. Evaluation of Anticancer, Antioxidant, and Possible Anti-inflammatory Properties of Selected Medicinal Plants Used in Indian Traditional Medication

    Directory of Open Access Journals (Sweden)

    Rafik Shaikh

    2014-10-01

    Full Text Available The present study was carried out to evaluate the anticancer, antioxidant, and possible anti-inflammatory properties of diverse medicinal plants frequently used in Indian traditional medication. The selected botanicals such as Soymida fembrifuga (Roxb. A. Juss. (Miliaceae, Tinospora cordifolia (Willd. Miers. (Menispermaceae, Lavandula bipinnata (L. O. Ktze. (Lamiaceae, and Helicteres isora L. (Sterculiaceae extracted in different solvents were evaluated for their in vitro anticancer and antioxidant activities. The results obtained indicate that H. isora has potent cytotoxic activity toward the selected cancer cells such as HeLa-B75 (34.21±0.24%, HL-60 (30.25±1.36%, HEP-3B (25.36±1.78%, and PN-15 (29.21±0.52%. Interestingly, the selected botanicals selectively inhibited cyclooxygenase-2 (COX-2 more than (COX-1, which are the key enzymes implicated in inflammation. COX-2 inhibition was observed to be in the range of 19.66-49.52% as compared to COX-1 inhibition (3.93-19.61%. The results of the antioxidant study revealed that the selected plants were found to be effective 1,1-diphenyl-2-picrylhydrazyl (DPPH, hydroxyl (OH, and superoxide radical (SOR scavenging agents. High-performance thin layer chromatography (HPTLC fingerprint of flavonoids was used as a measure of quality control of the selected plant samples. The results of the present findings strengthen the potential of the selected plants as a resource for the discovery of novel anticancer, anti-inflammatory, and antioxidant agents.

  16. Evaluation of Anticancer, Antioxidant, and Possible Anti-inflammatory Properties of Selected Medicinal Plants Used in Indian Traditional Medication.

    Science.gov (United States)

    Shaikh, Rafik; Pund, Mahesh; Dawane, Ashwini; Iliyas, Sayyed

    2014-10-01

    The present study was carried out to evaluate the anticancer, antioxidant, and possible anti-inflammatory properties of diverse medicinal plants frequently used in Indian traditional medication. The selected botanicals such as Soymida fembrifuga (Roxb.) A. Juss. (Miliaceae), Tinospora cordifolia (Willd.) Miers. (Menispermaceae), Lavandula bipinnata (L.) O. Ktze. (Lamiaceae), and Helicteres isora L. (Sterculiaceae) extracted in different solvents were evaluated for their in vitro anticancer and antioxidant activities. The results obtained indicate that H. isora has potent cytotoxic activity toward the selected cancer cells such as HeLa-B75 (34.21 ± 0.24%), HL-60 (30.25 ± 1.36%), HEP-3B (25.36 ± 1.78%), and PN-15 (29.21 ± 0.52%). Interestingly, the selected botanicals selectively inhibited cyclooxygenase-2 (COX-2) more than (COX-1), which are the key enzymes implicated in inflammation. COX-2 inhibition was observed to be in the range of 19.66-49.52% as compared to COX-1 inhibition (3.93-19.61%). The results of the antioxidant study revealed that the selected plants were found to be effective 1,1-diphenyl-2-picrylhydrazyl (DPPH), hydroxyl (OH), and superoxide radical (SOR) scavenging agents. High-performance thin layer chromatography (HPTLC) fingerprint of flavonoids was used as a measure of quality control of the selected plant samples. The results of the present findings strengthen the potential of the selected plants as a resource for the discovery of novel anticancer, anti-inflammatory, and antioxidant agents.

  17. Orientation selectivity in inhibition-dominated networks of spiking neurons: effect of single neuron properties and network dynamics.

    Science.gov (United States)

    Sadeh, Sadra; Rotter, Stefan

    2015-01-01

    The neuronal mechanisms underlying the emergence of orientation selectivity in the primary visual cortex of mammals are still elusive. In rodents, visual neurons show highly selective responses to oriented stimuli, but neighboring neurons do not necessarily have similar preferences. Instead of a smooth map, one observes a salt-and-pepper organization of orientation selectivity. Modeling studies have recently confirmed that balanced random networks are indeed capable of amplifying weakly tuned inputs and generating highly selective output responses, even in absence of feature-selective recurrent connectivity. Here we seek to elucidate the neuronal mechanisms underlying this phenomenon by resorting to networks of integrate-and-fire neurons, which are amenable to analytic treatment. Specifically, in networks of perfect integrate-and-fire neurons, we observe that highly selective and contrast invariant output responses emerge, very similar to networks of leaky integrate-and-fire neurons. We then demonstrate that a theory based on mean firing rates and the detailed network topology predicts the output responses, and explains the mechanisms underlying the suppression of the common-mode, amplification of modulation, and contrast invariance. Increasing inhibition dominance in our networks makes the rectifying nonlinearity more prominent, which in turn adds some distortions to the otherwise essentially linear prediction. An extension of the linear theory can account for all the distortions, enabling us to compute the exact shape of every individual tuning curve in our networks. We show that this simple form of nonlinearity adds two important properties to orientation selectivity in the network, namely sharpening of tuning curves and extra suppression of the modulation. The theory can be further extended to account for the nonlinearity of the leaky model by replacing the rectifier by the appropriate smooth input-output transfer function. These results are robust and do not

  18. Orientation selectivity in inhibition-dominated networks of spiking neurons: effect of single neuron properties and network dynamics.

    Directory of Open Access Journals (Sweden)

    Sadra Sadeh

    2015-01-01

    Full Text Available The neuronal mechanisms underlying the emergence of orientation selectivity in the primary visual cortex of mammals are still elusive. In rodents, visual neurons show highly selective responses to oriented stimuli, but neighboring neurons do not necessarily have similar preferences. Instead of a smooth map, one observes a salt-and-pepper organization of orientation selectivity. Modeling studies have recently confirmed that balanced random networks are indeed capable of amplifying weakly tuned inputs and generating highly selective output responses, even in absence of feature-selective recurrent connectivity. Here we seek to elucidate the neuronal mechanisms underlying this phenomenon by resorting to networks of integrate-and-fire neurons, which are amenable to analytic treatment. Specifically, in networks of perfect integrate-and-fire neurons, we observe that highly selective and contrast invariant output responses emerge, very similar to networks of leaky integrate-and-fire neurons. We then demonstrate that a theory based on mean firing rates and the detailed network topology predicts the output responses, and explains the mechanisms underlying the suppression of the common-mode, amplification of modulation, and contrast invariance. Increasing inhibition dominance in our networks makes the rectifying nonlinearity more prominent, which in turn adds some distortions to the otherwise essentially linear prediction. An extension of the linear theory can account for all the distortions, enabling us to compute the exact shape of every individual tuning curve in our networks. We show that this simple form of nonlinearity adds two important properties to orientation selectivity in the network, namely sharpening of tuning curves and extra suppression of the modulation. The theory can be further extended to account for the nonlinearity of the leaky model by replacing the rectifier by the appropriate smooth input-output transfer function. These results are

  19. Enhancing the mathematical properties of new haplotype homozygosity statistics for the detection of selective sweeps.

    Science.gov (United States)

    Garud, Nandita R; Rosenberg, Noah A

    2015-06-01

    Soft selective sweeps represent an important form of adaptation in which multiple haplotypes bearing adaptive alleles rise to high frequency. Most statistical methods for detecting selective sweeps from genetic polymorphism data, however, have focused on identifying hard selective sweeps in which a favored allele appears on a single haplotypic background; these methods might be underpowered to detect soft sweeps. Among exceptions is the set of haplotype homozygosity statistics introduced for the detection of soft sweeps by Garud et al. (2015). These statistics, examining frequencies of multiple haplotypes in relation to each other, include H12, a statistic designed to identify both hard and soft selective sweeps, and H2/H1, a statistic that conditional on high H12 values seeks to distinguish between hard and soft sweeps. A challenge in the use of H2/H1 is that its range depends on the associated value of H12, so that equal H2/H1 values might provide different levels of support for a soft sweep model at different values of H12. Here, we enhance the H12 and H2/H1 haplotype homozygosity statistics for selective sweep detection by deriving the upper bound on H2/H1 as a function of H12, thereby generating a statistic that normalizes H2/H1 to lie between 0 and 1. Through a reanalysis of resequencing data from inbred lines of Drosophila, we show that the enhanced statistic both strengthens interpretations obtained with the unnormalized statistic and leads to empirical insights that are less readily apparent without the normalization. Copyright © 2015 Elsevier Inc. All rights reserved.

  20. Properties of internalization factors contributing to the uptake of extracellular DNA into tumor-initiating stem cells of mouse Krebs-2 cell line.

    Science.gov (United States)

    Dolgova, Evgeniya V; Potter, Ekaterina A; Proskurina, Anastasiya S; Minkevich, Alexandra M; Chernych, Elena R; Ostanin, Alexandr A; Efremov, Yaroslav R; Bayborodin, Sergey I; Nikolin, Valeriy P; Popova, Nelly A; Kolchanov, Nikolay A; Bogachev, Sergey S

    2016-05-25

    Previously, we demonstrated that poorly differentiated cells of various origins, including tumor-initiating stem cells present in the ascites form of mouse cancer cell line Krebs-2, are capable of naturally internalizing both linear double-stranded DNA and circular plasmid DNA. The method of co-incubating Krebs-2 cells with extracellular plasmid DNA (pUC19) or TAMRA-5'-dUTP-labeled polymerase chain reaction (PCR) product was used. It was found that internalized plasmid DNA isolated from Krebs-2 can be transformed into competent Escherichia coli cells. Thus, the internalization processes taking place in the Krebs-2 cell subpopulation have been analyzed and compared, as assayed by E. coli colony formation assay (plasmid DNA) and cytofluorescence (TAMRA-DNA). We showed that extracellular DNA both in the form of plasmid DNA and a PCR product is internalized by the same subpopulation of Krebs-2 cells. We found that the saturation threshold for Krebs-2 ascites cells is 0.5 μg DNA/10(6) cells. Supercoiled plasmid DNA, human high-molecular weight DNA, and 500 bp PCR fragments are internalized into the Krebs-2 tumor-initiating stem cells via distinct, non-competing internalization pathways. Under our experimental conditions, each cell may harbor 340-2600 copies of intact plasmid material, or up to 3.097 ± 0.044×10(6) plasmid copies (intact or not), as detected by quantitative PCR. The internalization dynamics of extracellular DNA, copy number of the plasmids taken up by the cells, and competition between different types of double-stranded DNA upon internalization into tumor-initiating stem cells of mouse ascites Krebs-2 have been comprehensively analyzed. Investigation of the extracellular DNA internalization into tumor-initiating stem cells is an important part of understanding their properties and possible destruction mechanisms. For example, a TAMRA-labeled DNA probe may serve as an instrument to develop a target for the therapy of cancer, aiming at elimination of

  1. Preparation and selected properties of ion-containing reverse osmosis membranes

    International Nuclear Information System (INIS)

    Hegazy, E.S.A.; Dessouki, A.M.

    1986-01-01

    Ion-containing reverse osmosis membranes were prepared by the post radiation grafting of 4-vinylpyridine onto low density polyethylene films, followed by quaternization of the pyridine rings in the graft chains to confer ionic character to the membranes. The effect of some preparation conditions on the grafting yield was investigated. Different quaternizing agents such as methyl iodide, allyl bromide, and hydrochloric acid were used for the quaternization of the graft chains. The effect of quaternizing agent and degree of grafting on the properties of the membranes such as swelling behaviour, specific electric resistance, water flux and salt rejection, was investigated. The properties of these ionic membranes did not deteriorate with the operation time and they show a great promise for the use in the field of reverse osmosis desalination of sea water. (author)

  2. Physical and optical properties of size-selective CdTe nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Fok, Alice [Department of Chemistry, The City College of New York, CUNY New York, NY 10031 (United States); Morales, Jorge [Department of Biology, City College of New York, CUNY New York, NY 10031 (United States); Sohel, Mohammad [Natural Sciences Department, Hostos College, CUNY Bronx, NY 10451 (United States)

    2010-06-15

    Physical and optical properties of colloidal cadmium telluride nanocrystals (CdTe NCs) were investigated. The CdTe NCs were synthesized by reacting elemental tellurium dissolved in tributylphosphine with a mixture of cadmium oxide, octadecene, and oleic acid. These NCs, which were characterized by transmission electron microscopy (TEM) are spherical and ranged from 5 to 7 nm in diameter. The identity of the compound post-synthesis was confirmed by X-Ray diffraction (XRD) patterns. UV-Vis and photoluminescence (PL) properties as grown and pure CdTe samples were investigated. Bright excitonic photoluminescence emission was observed (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  3. Mechanical and fracture properties at impact loading of selected steels for nuclear power engineering

    International Nuclear Information System (INIS)

    Buchar, J.; Bilek, Z.

    1988-01-01

    The possibilities are briefly characterized of experimental research of mechanical and fracture properties of steels used in nuclear power engineering. Attention is paid to plastic deformation and the assessment of fracture formation during impact loading. The results are reported for steels 15Kh2MFA and 10GN2MFA. For steel 15Kh2MFA the effect was also studied of neutron radiation at different temperatures. From the theory developed for non-irradiated material 10GN2MFA, a prediction is made within the original model of the fracture stress value for steel 15Kh2MFA in both non-irradiated and irradiated states. The conclusion is arrived at that the existing methods of assessing steel properties at impact load allow obtaining knowledge of all significant effects during actual stress, this using only small specimens of the materials. (Z.M.). 4 figs., 8 refs

  4. Structure and properties of nanocrystalline nickel prepared by selective leaching at different temperatures

    Czech Academy of Sciences Publication Activity Database

    Michalcová, A.; Marek, I.; Len, A.; Heczko, Oleg; Drahokoupil, Jan; Vojtěch, D.; Huber, Š.; Nováková, R.

    2017-01-01

    Roč. 89, č. 4 (2017), s. 545-552 ISSN 0033-4545 R&D Projects: GA ČR GBP108/12/G043 Institutional support: RVO:68378271 Keywords : magnetic properties * magnetization * nanocrystals * neutron scattering * nickel * SANS * SSC-2016 * X-ray diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 2.626, year: 2016

  5. Examinations of Selected Thermal Properties of Packages of SiC Schottky Diodes

    Directory of Open Access Journals (Sweden)

    Bisewski Damian

    2016-09-01

    Full Text Available This paper describes the study of thermal properties of packages of silicon carbide Schottky diodes. In the paper the packaging process of Schottky diodes, the measuring method of thermal parameters, as well as the results of measurements are presented. The measured waveforms of transient thermal impedance of the examined diodes are compared with the waveforms of this parameter measured for commercially available Schottky diodes.

  6. Heavy Metal uptake Potentials of Pseudomonas aeruginosa and ...

    African Journals Online (AJOL)

    Uptake of heavy metals, silver and cadmium by Pseudomonas aeruginosa (a Gram negative bacterium) and Micrococcus luteus (a Gram positive bacterium) was investigated in Cadmium and Silver stock solution using ion selective electrodes. Silver and cadmium uptake by the two organisms was described by Langmuir ...

  7. Comparative studies on flour proximate compositions and functional properties of selected Pakistani rice varieties

    International Nuclear Information System (INIS)

    Jamal, S.; Qazi, I.M.; Ahmed, I.

    2016-01-01

    The aim of this study was to evaluate the proximate and functional properties of flours obtained from various rice varieties, i.e., Super Basmati Shaheen, Super Basmati Kainat, Super Fine, JP5, Basmati 385, Fakhr-e-Malakand grown in different areas of Pakistan. Moisture content, ash content, crude protein, crude fat, water absorption index, water solubility and swelling power varied significantly (P<0.05) from each other. Moisture content, ash content, crude protein and crude fat of rice flour ranged from 5.46-7.08 percentage, 0.48-1.23 percentage, 8.02-9.85 percentage and 0.43-1.5 percentage, respectively. While, functional properties such as water absorption index, water solubility index and swelling power were found in the range of 5.38-6.26 (g/g), 1.95-4.94 percentage and 5.74-7.64 (g/g), respectively. The results showed that the functional properties of rice flour were greatly influenced by the compositional variations of various rice varieties. (author)

  8. Tuning the electronic properties of armchair carbon nanoribbons by a selective boron doping

    International Nuclear Information System (INIS)

    Navarro-Santos, P; Ricardo-Chavez, J L; Lopez-Sandoval, R; Reyes-Reyes, M; Rivera, J L

    2010-01-01

    Armchair carbon nanoribbons (ACNRs) substitutionally doped with boron atoms are investigated in the framework of first-principles density functional theory. Different boron-boron arrangements and concentrations are considered in order to simulate possible aggregation patterns, their structural stability and electronic behavior are determined as a function of ribbon size. In agreement with previous studies, our results show that the dopant atoms have in general a preference for edge sites, but specific effects appear as a function of concentration that importantly modify the properties of the ribbons compared to the pristine case. Interesting tendencies are discovered as a function of dopant concentration that significantly affect the electronic properties of the ribbons. We have found that BC 3 island formation and edge doping are the most important factors for the structural stabilization of the ribbons with high boron concentration (>7%) whereas for the cases of low boron concentrations ( 3 island patterns give rise to highly localized B states on top of the Fermi level, resulting in semiconducting behavior. On the other hand, when the average distance between the B atoms increases beyond island stoichiometry, the localization of their states is reduced and the ribbons may become metallic due to a band crossing caused by the lowering of the Fermi level resulting from the positive charge doping. Thus, tuning the dopant interaction would be an appropriate way to tailor the electronic properties of the ribbons in a convenient manner in view of potential technological applications.

  9. A Principle Component Analysis of Galaxy Properties from a Large, Gas-Selected Sample

    Directory of Open Access Journals (Sweden)

    Yu-Yen Chang

    2012-01-01

    concluded that this is in conflict with the CDM model. Considering the importance of the issue, we reinvestigate the problem using the principal component analysis on a fivefold larger sample and additional near-infrared data. We use databases from the Arecibo Legacy Fast Arecibo L-band Feed Array Survey for the gas properties, the Sloan Digital Sky Survey for the optical properties, and the Two Micron All Sky Survey for the near-infrared properties. We confirm that the parameters are indeed correlated where a single physical parameter can explain 83% of the variations. When color (g-i is included, the first component still dominates but it develops a second principal component. In addition, the near-infrared color (i-J shows an obvious second principal component that might provide evidence of the complex old star formation. Based on our data, we suggest that it is premature to pronounce the failure of the CDM model and it motivates more theoretical work.

  10. The effect of selected supercritical CO2 plant extract addition on user properties of shower gels

    Directory of Open Access Journals (Sweden)

    Vogt Otmar

    2014-12-01

    Full Text Available The formulations of washing cosmetics i.e. shower gels, containing extracts obtained during supercritical CO2 extraction process as active ingredient, were developed. The subject of the study was the analysis of the physicochemical and user properties of the obtained products. In the work supercritical CO2 extracts of black currant seeds, strawberry seeds, hop cones and mint leafs were used. The formulation contains a mixture of surfactants (disodium cocoamphodiacetate, disodium laureth sulfosuccinate, cocoamide DEA, cocoamidepropyl betaine, Sodium Laureth Sulfate. Various thickener agents were applied to the obtained desired rheological properties of the cosmetics. Among others, sorbitol acetal derivatives, methylhydroxypropylcellulose and C10-30 alkyl acrylate crosspolymer were used. For stable products, the effect of extracts addition (black currants seeds, strawberries seeds, mint and hops, obtained from supercritical CO2 extraction process on the cosmetics properties, such as pH, viscosity, detergency and foam ability, were determined. The obtained results showed that the extracts could be used as components of shower gels.

  11. Computer simulation of the optical properties of high-temperature cermet solar selective coatings

    Energy Technology Data Exchange (ETDEWEB)

    Nejati, M. Reza [K.N. Toosi Univ. of Technology, Dept. of Mechanical Engineering, Tehran (Iran); Fathollahi, V.; Asadi, M. Khalaji [AEOI, Center for Renewable Energy Research and Applications (CRERA), Tehran (Iran)

    2005-02-01

    A computer simulation is developed to calculate the solar absorptance and thermal emittance of various configurations of cermet solar selective coatings. Special attention has been paid to those material combinations, which are commonly used in high-temperature solar thermal applications. Moreover, other material combinations such as two-, three- and four-cermet-layer structures as solar selective coatings have been theoretically analyzed by computer simulation using three distinct physical models of Ping Sheng, Maxwell-Garnett and Bruggeman. The novel case of two-cermet-layer structure with different cermet components has also been investigated. The results were optimized by allowing the program to manipulate the metal volume fraction and thickness of each layer and the results compared to choose the best possible configuration. The calculated results are within the range of 0.91-0.97 for solar absorptance and 0.02-0.07 for thermal emittance at room temperature. (Author)

  12. Thermal and mechanical properties of selected 3D printed thermoplastics in the cryogenic temperature regime

    International Nuclear Information System (INIS)

    Weiss, K-P; Bagrets, N; Lange, C; Goldacker, W; Wohlgemuth, J

    2015-01-01

    Insulating materials for use in cryogenic boundary conditions are still limited to a proved selection as Polyamid, Glasfiber reinforced resins, PEEK, Vespel etc. These materials are usually formed to parts by mechanical machining or sometimes by cast methods. Shaping complex geometries in one piece is limited. Innovative 3D printing is now an upcoming revolutionary technology to construct functional parts from a couple of thermoplastic materials as ABS, Nylon and others which possess quite good mechanical stability and allow realizing very complex shapes with very subtle details. Even a wide range of material mixtures is an option and thermal treatments can be used to finish the material structure for higher performance. The use of such materials in cryogenic environment is very attractive but so far poor experience exists. In this paper, first investigations of the thermal conductivity, expansion and mechanical strength are presented for a few selected commercial 3D material samples to evaluate their application prospects in the cryogenic temperature regime. (paper)

  13. Thyroid uptake software

    International Nuclear Information System (INIS)

    Alonso, Dolores; Arista, Eduardo

    2003-01-01

    The DETEC-PC software was developed as a complement to a measurement system (hardware) able to perform Iodine Thyroid Uptake studies. The software was designed according to the principles of Object oriented programming using C++ language. The software automatically fixes spectrometric measurement parameters and besides patient measurement also performs statistical analysis of a batch of samples. It possesses a PARADOX database with all information of measured patients and a help system with the system options and medical concepts related to the thyroid uptake study

  14. Seed selection by earthworms : chemical seed properties matter more than morphological traits

    OpenAIRE

    Clause, J.; Forey, E.; Eisenhauer, N.; Seal, C.E.; Soudey, A.; Colville, L.; Barot, Sébastien

    2017-01-01

    Aims : The passage of seeds through the earthworm gut potentially damages seeds, altering seed and seedling performances depending on seed traits. This work was conducted to study to what extent chemical and morphological seed traits determine the seed attractiveness for earthworms. Methods : We tested seed selection via the ingestion and digestion of 23 grassland plant species spanning a range of 14 morphological and chemical traits by two common earthworm species: the anecic Lumbricus te...

  15. Modulation in selectivity and allosteric properties of small-molecule ligands for CC-chemokine receptors

    DEFF Research Database (Denmark)

    Thiele, Stefanie; Malmgaard-Clausen, Mikkel; Engel-Andreasen, Jens

    2012-01-01

    Among 18 human chemokine receptors, CCR1, CCR4, CCR5, and CCR8 were activated by metal ion Zn(II) or Cu(II) in complex with 2,2'-bipyridine or 1,10-phenanthroline with similar potencies (EC(50) from 3.9 to 172 μM). Besides being agonists, they acted as selective allosteric enhancers of CCL3. Thes...

  16. Profiles of Reservoir Properties of Oil-Bearing Plays for Selected Petroleum Provinces in the United States

    Science.gov (United States)

    Freeman, P.A.; Attanasi, E.D.

    2015-11-05

    Profiles of reservoir properties of oil-bearing plays for selected petroleum provinces in the United States were developed to characterize the database to be used for a potential assessment by the U.S. Geological Survey (USGS) of oil that would be technically recoverable by the application of enhanced oil recovery methods using injection of carbon dioxide (CO2-EOR). The USGS assessment methodology may require reservoir-level data for the purposes of screening conventional oil reservoirs and projecting CO2-EOR performance in terms of the incremental recoverable oil. The information used in this report is based on reservoir properties from the “Significant Oil and Gas Fields of the United States Database” prepared by Nehring Associates, Inc. (2012). As described by Nehring Associates, Inc., the database “covers all producing provinces (basins) in the United States except the Appalachian Basin and the Cincinnati Arch.”

  17. Microstructure and tensile properties of Ti-6Al-4V alloys manufactured by selective laser melting with optimized processing parameters

    Science.gov (United States)

    Wang, L.; Ma, C.; Huang, J.; Ding, H. Y.; Chu, M. Q.

    2017-11-01

    Selective laser melting (SLM) is a precise additive manufacturing process that the metallic powders without binder are melted layer by layer to complex components using a high bright fiber laser. In the paper, Ti-6Al-4V alloy was fabricated by SLM and its microstructure and mechanical properties were investigated in order to evaluate the SLM process. The results show that the microstructure exists anisotropy between the horizontal and vertical section due to the occurrence of epitaxial growth, and the former microstructure seems equal-axis and the latter is column. Moreover, there is little difference in tensile test between the horizontal and vertical sections. Furthermore, the tensile properties of fabricated Ti-6Al-4V alloy by SLM are higher than the forged standard ones. However, the fatigue results show that there are some scatters, which need further investigation to define the fatigue initiation.

  18. Structure and Mechanical Properties of the AlSi10Mg Alloy Samples Manufactured by Selective Laser Melting

    Science.gov (United States)

    Li, Xiaodan; Ni, Jiaqiang; Zhu, Qingfeng; Su, Hang; Cui, Jianzhong; Zhang, Yifei; Li, Jianzhong

    2017-11-01

    The AlSi10Mg alloy samples with the size of 14×14×91mm were produced by the selective laser melting (SLM) method in different building direction. The structures and the properties at -70°C of the sample in different direction were investigated. The results show that the structure in different building direction shows different morphology. The fish scale structures distribute on the side along the building direction, and the oval structures distribute on the side vertical to the building direction. Some pores in with the maximum size of 100 μm exist of the structure. And there is no major influence for the build orientation on the tensile properties. The tensile strength and the elongation of the sample in the building direction are 340 Mpa and 11.2 % respectively. And the tensile strength and the elongation of the sample vertical to building direction are 350 Mpa and 13.4 % respectively

  19. Defect, Microstructure, and Mechanical Property of Ti-6Al-4V Alloy Fabricated by High-Power Selective Laser Melting

    Science.gov (United States)

    Cao, Sheng; Chen, Zhuoer; Lim, Chao Voon Samuel; Yang, Kun; Jia, Qingbo; Jarvis, Tom; Tomus, Dacian; Wu, Xinhua

    2017-12-01

    To improve the selective laser melting (SLM) productivity, a high laser power and accordingly adjusted parameters are employed to facilitate a high build rate. Three distinct processing strategies with incremental build rate are developed for SLM Ti-6Al-4V. Various types of defects are investigated. Further studies were carried out by heat-treatment and hot isostatic pressing to evaluate the influence of microstructure and porosity on mechanical properties. The anisotropic mechanical property in horizontally and vertically build samples were observed, which was attributable to the columnar grains and spatial arrangement of defects. Regardless of anisotropy, a post-SLM heat-treatment at 800°C for 2 h produces a combined high strength and ductility.

  20. On the Selective Laser Melting (SLM of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Francesco Trevisan

    2017-01-01

    Full Text Available The aim of this review is to analyze and to summarize the state of the art of the processing of aluminum alloys, and in particular of the AlSi10Mg alloy, obtained by means of the Additive Manufacturing (AM technique known as Selective Laser Melting (SLM. This process is gaining interest worldwide, thanks to the possibility of obtaining a freeform fabrication coupled with high mechanical properties related to a very fine microstructure. However, SLM is very complex, from a physical point of view, due to the interaction between a concentrated laser source and metallic powders, and to the extremely rapid melting and the subsequent fast solidification. The effects of the main process variables on the properties of the final parts are analyzed in this review: from the starting powder properties, such as shape and powder size distribution, to the main process parameters, such as laser power and speed, layer thickness, and scanning strategy. Furthermore, a detailed overview on the microstructure of the AlSi10Mg material, with the related tensile and fatigue properties of the final SLM parts, in some cases after different heat treatments, is presented.

  1. Physical and chemical properties of selected agricultural byproduct-based activated carbons and their ability to adsorb geosmin

    Energy Technology Data Exchange (ETDEWEB)

    Ng, C.; Losso, J.N.; Rao, R.M. [Louisiana State University Agricultural Center, Baton Rouge, LA (United States). Department of Food Science; Marshall, W.E. [USDA-ARS, Southern Regional Research Center, New Orleans, LA (United States)

    2002-09-01

    The objectives of this study were to evaluate selected physical and chemical properties of agricultural byproduct-based activated carbons made from pecan shells and sugarcane bagasse, and compare those properties to a commercial coal-based activated carbon as well as to compare the adsorption efficiency of these carbons for geosmin. Comparison of the physical and chemical properties of pecan shell- and bagasse-based carbons to the commercial carbon, Calgon Filtrasorb 400, showed that pecan shell carbon, but not the bagasse carbon, compared favorably to Filtrasorb 400, especially in terms of surface area, bulk density, ash and attrition. A carbon dosage study done in a model system showed the amount of geosmin adsorbed to be greater for Filtrasorb 400 and the bagasse-based carbon at low carbon concentrations than for the pecan shell carbons, but geosmin adsorption was similar in all carbons at higher carbon dosages. Application of the Freundlich isotherm model to the adsorption data showed that carbons made by steam activation of pecan shells or sugarcane bagasse had geosmin adsorption characteristics most like those of the commercial carbon. In terms of physical, chemical and adsorptive properties, steam-activated pecan shell carbon most resembled the commercial carbon and has the potential to replace Filtrasorb 400 in applications involving removal of geosmin from aqueous environments. (author)

  2. The Effect of Carbon Nanotubes on the Mechanical Properties of Wood Plastic Composites by Selective Laser Sintering

    Directory of Open Access Journals (Sweden)

    Yunhe Zhang

    2017-12-01

    Full Text Available Wood-plastic composites (WPCs made by selective laser sintering (SLS approach of 3D printing offer many advantages over single polymer materials, such as low cost, sustainability, and better sintering accuracy. However, WPCs made via SLS are too weak to have widespread applications. In order to increase the mechanical properties of WPCs, a novel type of WPCs containing 0, 0.05, 0.1 and 0.15 wt % carbon nanotubes (CNT, 14 wt % wood fibers, 86 wt % polyether sulfone (PES was manufactured via SLS. The experimental results showed that the addition of small amount of CNTs can significantly increase the mechanical properties of the wood/PES composite material. The tensile strength, bending strength, and elasticity modulus were 76.3%, 227.9%, and 128.7% higher with 0.1 wt % CNTs than those without CNTs. The mechanical properties of specimens first increased and then decreased with the addition of CNTs. The SEM results of the specimens’ fracture morphology indicate that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons why the composites possessed superior mechanical properties: CNTs facilitate the laser sintering process of WPCs due to their thermal conductivities, and CNTs directly reinforce WPCs.

  3. A novel coping metal material CoCrCu alloy fabricated by selective laser melting with antimicrobial and antibiofilm properties.

    Science.gov (United States)

    Ren, Ling; Memarzadeh, Kaveh; Zhang, Shuyuan; Sun, Ziqing; Yang, Chunguang; Ren, Guogang; Allaker, Robert P; Yang, Ke

    2016-10-01

    The aim of this study was to fabricate a novel coping metal CoCrCu alloy using a selective laser melting (SLM) technique with antimicrobial and antibiofilm activities and to investigate its microstructure, mechanical properties, corrosion resistance and biocompatibility. Novel CoCrCu alloy was fabricated using SLM from a mixture of commercial CoCr based alloy and elemental Cu powders. SLM CoCr without Cu served as control. Antibacterial activity was analyzed using standard antimicrobial tests, and antibiofilm properties were investigated using confocal laser scanning microscope. Cu distribution and microstructure were determined using scanning electron microscope, optical microscopy and X-ray diffraction. Corrosion resistance was evaluated by potential dynamic polarization and biocompatibility measured using an MTT assay. SLM CoCrCu alloys were found to be bactericidal and able to inhibit biofilm formation. Other factors such as microstructure, mechanical properties, corrosion resistance and biocompatibility were similar to those of SLM CoCr alloys. The addition of appropriate amounts of Cu not only maintains normal beneficial properties of CoCr based alloys, but also provides SLM CoCrCu alloys with excellent antibacterial and antibiofilm capabilities. This material has the potential to be used as a coping metal for dental applications. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties.

    Science.gov (United States)

    Trevisan, Francesco; Calignano, Flaviana; Lorusso, Massimo; Pakkanen, Jukka; Aversa, Alberta; Ambrosio, Elisa Paola; Lombardi, Mariangela; Fino, Paolo; Manfredi, Diego

    2017-01-18

    The aim of this review is to analyze and to summarize the state of the art of the processing of aluminum alloys, and in particular of the AlSi10Mg alloy, obtained by means of the Additive Manufacturing (AM) technique known as Selective Laser Melting (SLM). This process is gaining interest worldwide, thanks to the possibility of obtaining a freeform fabrication coupled with high mechanical properties related to a very fine microstructure. However, SLM is very complex, from a physical point of view, due to the interaction between a concentrated laser source and metallic powders, and to the extremely rapid melting and the subsequent fast solidification. The effects of the main process variables on the properties of the final parts are analyzed in this review: from the starting powder properties, such as shape and powder size distribution, to the main process parameters, such as laser power and speed, layer thickness, and scanning strategy. Furthermore, a detailed overview on the microstructure of the AlSi10Mg material, with the related tensile and fatigue properties of the final SLM parts, in some cases after different heat treatments, is presented.

  5. Selective Laser Melting Produced Ti-6Al-4V: Post-Process Heat Treatments to Achieve Superior Tensile Properties

    Directory of Open Access Journals (Sweden)

    Gerrit M. Ter Haar

    2018-01-01

    Full Text Available Current post-process heat treatments applied to selective laser melting produced Ti-6Al-4V do not achieve the same microstructure and therefore superior tensile behaviour of thermomechanical processed wrought Ti-6Al-4V. Due to the growing demand for selective laser melting produced parts in industry, research and development towards improved mechanical properties is ongoing. This study is aimed at developing post-process annealing strategies to improve tensile behaviour of selective laser melting produced Ti-6Al-4V parts. Optical and electron microscopy was used to study α grain morphology as a function of annealing temperature, hold time and cooling rate. Quasi-static uniaxial tensile tests were used to measure tensile behaviour of different annealed parts. It was found that elongated α’/α grains can be fragmented into equiaxial grains through applying a high temperature annealing strategy. It is shown that bi-modal microstructures achieve a superior tensile ductility to current heat treated selective laser melting produced Ti-6Al-4V samples.

  6. Selective Laser Melting Produced Ti-6Al-4V: Post-Process Heat Treatments to Achieve Superior Tensile Properties.

    Science.gov (United States)

    Ter Haar, Gerrit M; Becker, Thorsten H

    2018-01-17

    Current post-process heat treatments applied to selective laser melting produced Ti-6Al-4V do not achieve the same microstructure and therefore superior tensile behaviour of thermomechanical processed wrought Ti-6Al-4V. Due to the growing demand for selective laser melting produced parts in industry, research and development towards improved mechanical properties is ongoing. This study is aimed at developing post-process annealing strategies to improve tensile behaviour of selective laser melting produced Ti-6Al-4V parts. Optical and electron microscopy was used to study α grain morphology as a function of annealing temperature, hold time and cooling rate. Quasi-static uniaxial tensile tests were used to measure tensile behaviour of different annealed parts. It was found that elongated α'/α grains can be fragmented into equiaxial grains through applying a high temperature annealing strategy. It is shown that bi-modal microstructures achieve a superior tensile ductility to current heat treated selective laser melting produced Ti-6Al-4V samples.

  7. The monoamine oxidase inhibition properties of selected structural analogues of methylene blue

    International Nuclear Information System (INIS)

    Delport, Anzelle; Harvey, Brian H.; Petzer, Anél; Petzer, Jacobus P.

    2017-01-01

    The thionine dye, methylene blue (MB), is a potent inhibitor of monoamine oxidase (MAO) A, a property that may, at least in part, mediate its antidepressant effects in humans and animals. The central inhibition of MAO-A by MB has also been linked to serotonin toxicity (ST) which may arise when MB is used in combination with serotonergic drugs. Structural analogues and the principal metabolite of MB, azure B, have also been reported to inhibit the MAO enzymes, with all compounds exhibiting specificity for the MAO-A isoform. To expand on the structure-activity relationships (SARs) of MAO inhibition by MB analogues, the present study investigates the human MAO inhibition properties of five MB analogues: neutral red, Nile blue, new methylene blue, cresyl violet and 1,9-dimethyl methylene blue. Similar to MB, these analogues also are specific MAO-A inhibitors with cresyl violet (IC 50 = 0.0037 μM), Nile blue (IC 50 = 0.0077 μM) and 1,9-dimethyl methylene blue (IC 50 = 0.018 μM) exhibiting higher potency inhibition compared to MB (IC 50 = 0.07 μM). Nile blue also represents a potent MAO-B inhibitor with an IC 50 value of 0.012 μM. From the results it may be concluded that non-thionine MB analogues (e.g. cresyl violet and Nile blue) also may exhibit potent MAO inhibition, a property which should be considered when using these compounds in pharmacological studies. Benzophenoxazines such as cresyl violet and Nile blue are, similar to phenothiazines (e.g. MB), representative of high potency MAO-A inhibitors with a potential risk of ST. - Highlights: • MB analogues, cresyl violet and Nile blue, are high potency MAO-A inhibitors. • Nile blue also represents a potent MAO-B inhibitor. • Potent MAO-A inhibition should alert to potential serotonin toxicity.

  8. The influence of Lactobacillus paracasei LPC-37 on selected properties of fermented sausages

    Directory of Open Access Journals (Sweden)

    Marcel Mati

    2015-05-01

    Full Text Available Fermented sausages rank among non-heat-treated meat products. Their nutritional properties are similar to the raw material, simultaneously their microbial safety and stability is ensured using additives and specific microbial cultures. The use of probiotic cultures can positively affect the processing of fermented sausages, resulting in the new technological properties and beneficial effect on human health. However, commercial application of probiotic microorganisms in fermented sausages is not common yet. Lactobacillus paracasei LPC-37 is a gram-positive, non-spore forming, homofermentative rod, which according to studies may modulate immune responses in human organism and survives the passage through the gastrointestinal tract. The main object of this work was to evaluate technological properties of L. paracasei LPC-37, which have not been fully examined. Two groups of fermented sausages were analysed in this work. The first group of fermented sausages was prepared using lyophilized starter culture (Lyocarni RHM-33. The second group of fermented sausages was prepared by the combination of lyophilized starter culture and potential probiotic culture Lactobacillus paracasei LPC-37. The processing and ripening of sausages were carried out in meat processing plant to simulate real conditions of production. The changes of the products (water activity, pH, concentration of organic acids and microbial growth were evaluated during ripening (3 weeks, while sensory analysis was carried out in the final stage of the process and during storage (3 weeks. It was found that the environment of raw-fermented sausages is suitable for the growth and survival of Lactobacillus paracasei LPC-37 and the microbiological quality of the final product was very good (absence of Salmonella and Listeria monocytogenes. The counts of lactobacilli reached 107 CFU/g of the product, which meet the requirements for functional foods. The results of the sensory evaluation showed

  9. Tuning the electronic properties of armchair carbon nanoribbons by a selective boron doping

    Energy Technology Data Exchange (ETDEWEB)

    Navarro-Santos, P; Ricardo-Chavez, J L; Lopez-Sandoval, R [Instituto Potosino de Investigacion Cientifica y Tecnologica, Camino a la presa San Jose 2055, San Luis Potosi 78216 (Mexico); Reyes-Reyes, M [Instituto de Investigacion en Comunicacion Optica, Universidad Autonoma de San Luis Potosi, Alvaro Obregon 64, San Luis Potosi 78000 (Mexico); Rivera, J L, E-mail: sandov@ipicyt.edu.m [Facultad de Ingenieria Quimica, Universidad Michoacana de San Nicolas de Hidalgo, Santiago Tapia 403, Morelia, Michoacan, 58000 (Mexico)

    2010-12-22

    Armchair carbon nanoribbons (ACNRs) substitutionally doped with boron atoms are investigated in the framework of first-principles density functional theory. Different boron-boron arrangements and concentrations are considered in order to simulate possible aggregation patterns, their structural stability and electronic behavior are determined as a function of ribbon size. In agreement with previous studies, our results show that the dopant atoms have in general a preference for edge sites, but specific effects appear as a function of concentration that importantly modify the properties of the ribbons compared to the pristine case. Interesting tendencies are discovered as a function of dopant concentration that significantly affect the electronic properties of the ribbons. We have found that BC{sub 3} island formation and edge doping are the most important factors for the structural stabilization of the ribbons with high boron concentration (>7%) whereas for the cases of low boron concentrations (<5%) the structural stabilities are similar. For all the doped cases, we have found that the BC{sub 3} island patterns give rise to highly localized B states on top of the Fermi level, resulting in semiconducting behavior. On the other hand, when the average distance between the B atoms increases beyond island stoichiometry, the localization of their states is reduced and the ribbons may become metallic due to a band crossing caused by the lowering of the Fermi level resulting from the positive charge doping. Thus, tuning the dopant interaction would be an appropriate way to tailor the electronic properties of the ribbons in a convenient manner in view of potential technological applications.

  10. Selective Assembly of Na,K-ATPase α2β2 Heterodimers in the Heart: DISTINCT FUNCTIONAL PROPERTIES AND ISOFORM-SELECTIVE INHIBITORS.

    Science.gov (United States)

    Habeck, Michael; Tokhtaeva, Elmira; Nadav, Yotam; Ben Zeev, Efrat; Ferris, Sean P; Kaufman, Randal J; Bab-Dinitz, Elizabeta; Kaplan, Jack H; Dada, Laura A; Farfel, Zvi; Tal, Daniel M; Katz, Adriana; Sachs, George; Vagin, Olga; Karlish, Steven J D

    2016-10-28

    The Na,K-ATPase α 2 subunit plays a key role in cardiac muscle contraction by regulating intracellular Ca 2+ , whereas α 1 has a more conventional role of maintaining ion homeostasis. The β subunit differentially regulates maturation, trafficking, and activity of α-β heterodimers. It is not known whether the distinct role of α 2 in the heart is related to selective assembly with a particular one of the three β isoforms. We show here by immunofluorescence and co-immunoprecipitation that α 2 is preferentially expressed with β 2 in T-tubules of cardiac myocytes, forming α 2 β 2 heterodimers. We have expressed human α 1 β 1 , α 2 β 1 , α 2 β 2 , and α 2 β 3 in Pichia pastoris, purified the complexes, and compared their functional properties. α 2 β 2 and α 2 β 3 differ significantly from both α 2 β 1 and α 1 β 1 in having a higher K 0.5 K + and lower K 0.5 Na + for activating Na,K-ATPase. These features are the result of a large reduction in binding affinity for extracellular K + and shift of the E 1 P-E 2 P conformational equilibrium toward E 1 P. A screen of perhydro-1,4-oxazepine derivatives of digoxin identified several derivatives (e.g. cyclobutyl) with strongly increased selectivity for inhibition of α 2 β 2 and α 2 β 3 over α 1 β 1 (range 22-33-fold). Molecular modeling suggests a possible basis for isoform selectivity. The preferential assembly, specific T-tubular localization, and low K + affinity of α 2 β 2 could allow an acute response to raised ambient K + concentrations in physiological conditions and explain the importance of α 2 β 2 for cardiac muscle contractility. The high sensitivity of α 2 β 2 to digoxin derivatives explains beneficial effects of cardiac glycosides for treatment of heart failure and potential of α 2 β 2 -selective digoxin derivatives for reducing cardiotoxicity. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

  11. Creating model systems for catalysis with mass-selected nanoparticles: Characterization and properties

    DEFF Research Database (Denmark)

    Sebök, Béla

    today plenty of industrial heterogeneous catalysts are based on nanoparticles and their properties. The chapters in this thesis contain research on different processes and give examples of the possibilities of nanoscale catalyst materials. Because of the wide range of processes and materials involved...... electrolyte showing the stability of the catalyst.Apart from (photo)electrochemical reactions, nanoparticles play a very importantrole in different heterogeneous catalytic reactions where the reactants are in the gas phase. In order to investigate some of these reactions we created model systems utilizing...

  12. Investigating the Influence of Waste Basalt Powder on Selected Properties of Cement Paste and Mortar

    Science.gov (United States)

    Dobiszewska, Magdalena; Beycioğlu, Ahmet

    2017-10-01

    Concrete is the most widely used man-made construction material in civil engineering applications. The consumption of cement and thus concrete, increases day by day along with the growth of urbanization and industrialization and due to new developments in construction technologies, population growing, increasing of living standard. Concrete production consumes much energy and large amounts of natural resources. It causes environmental, energy and economic losses. The most important material in concrete production is cement. Cement industry contributes to production of about 7% of all CO2 generated in the world. Every ton of cement production releases nearly one ton of CO2 to atmosphere. Thus the concrete and cement industry changes the environment appearance and influences it very much. Therefore, it has become very important for construction industry to focus on minimizing the environmental impact, reducing energy consumption and limiting CO2 emission. The need to meet these challenges has spurred an interest in the development of a blended Portland cement in which the amount of clinker is reduced and partially replaced with mineral additives - supplementary cementitious materials (SCMs). Many researchers have studied the possibility of using another mineral powder in mortar and concrete production. The addition of marble dust, basalt powder, granite or limestone powder positively affects some properties of cement mortar and concrete. This paper presents an experimental study on the properties of cement paste and mortar containing basalt powder. The basalt powder is a waste emerged from the preparation of aggregate used in asphalt mixture production. Previous studies have shown that analysed waste used as a fine aggregate replacement, has a beneficial effect on some properties of mortar and concrete, i.e. compressive strength, flexural strength and freeze resistance also. The present study shows the results of the research concerning the modification of cement

  13. Selection and properties of alternative forming fluids for TRISO fuel kernel production

    Energy Technology Data Exchange (ETDEWEB)

    Baker, M.P. [Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); King, J.C., E-mail: kingjc@mines.edu [Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Gorman, B.P. [Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Marshall, D.W. [Idaho National Laboratory, 2525 N. Fremont Avenue, P.O. Box 1625, Idaho Falls, ID 83415 (United States)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer Forming fluid selection criteria developed for TRISO kernel production. Black-Right-Pointing-Pointer Ten candidates selected for further study. Black-Right-Pointing-Pointer Density, viscosity, and surface tension measured for first time. Black-Right-Pointing-Pointer Settling velocity and heat transfer rates calculated. Black-Right-Pointing-Pointer Three fluids recommended for kernel production testing. - Abstract: Current Very High Temperature Reactor (VHTR) designs incorporate TRi-structural ISOtropic (TRISO) fuel, which consists of a spherical fissile fuel kernel surrounded by layers of pyrolytic carbon and silicon carbide. An internal sol-gel process forms the fuel kernel using wet chemistry to produce uranium oxyhydroxide gel spheres by dropping a cold precursor solution into a hot column of trichloroethylene (TCE). Over time, gelation byproducts inhibit complete gelation, and the TCE must be purified or discarded. The resulting TCE waste stream contains both radioactive and hazardous materials and is thus considered a mixed hazardous waste. Changing the forming fluid to a non-hazardous alternative could greatly improve the economics of TRISO fuel kernel production. Selection criteria for a replacement forming fluid narrowed a list of {approx}10,800 chemicals to yield ten potential replacement forming fluids: 1-bromododecane, 1-bromotetradecane, 1-bromoundecane, 1-chlorooctadecane, 1-chlorotetradecane, 1-iododecane, 1-iodododecane, 1-iodohexadecane, 1-iodooctadecane, and squalane. The density, viscosity, and surface tension for each potential replacement forming fluid were measured as a function of temperature between 25 Degree-Sign C and 80 Degree-Sign C. Calculated settling velocities and heat transfer rates give an overall column height approximation. 1-bromotetradecane, 1-chlorooctadecane, and 1-iodododecane show the greatest promise as replacements, and future tests will verify their ability to form satisfactory

  14. Anxiogenic properties of an inverse agonist selective for α3 subunit-containing GABAA receptors

    OpenAIRE

    Atack, John R; Hutson, Peter H; Collinson, Neil; Marshall, George; Bentley, Graham; Moyes, Christopher; Cook, Susan M; Collins, Ian; Wafford, Keith; McKernan, Ruth M; Dawson, Gerard R

    2005-01-01

    α3IA (6-(4-pyridyl)-5-(4-methoxyphenyl)-3-carbomethoxy-1-methyl-1H-pyridin-2-one) is a pyridone with higher binding and functional affinity and greater inverse agonist efficacy for GABAA receptors containing an α3 rather than an α1, α2 or α5 subunit. If doses are selected that minimise the occupancy at these latter subtypes, then the in vivo effects of α3IA are most probably mediated by the α3 subtype.α3IA has good CNS penetration in rats and mice as measured using a [3H]Ro 15-1788 in vivo bi...

  15. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available Toggle navigation Test/Treatment Patient Type Screening/Wellness Disease/Condition Safety En Español More Info Images/Videos About Us News Physician Resources Professions Site Index A-Z Thyroid Scan and Uptake ...

  16. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... information. The thyroid scan and thyroid uptake provide information about the structure and function of the thyroid. The thyroid is a gland in the neck that controls metabolism , a chemical process that regulates the rate at which the body ...

  17. Radioactive uptake by plants

    Energy Technology Data Exchange (ETDEWEB)

    Horak, O

    1986-01-01

    The fundamentals of radionuclide uptake by plants, both by leaves and roots are presented. Iodine, cesium, strontium and ruthenium are considered and a table of the measured concentrations in several agricultural plants shortly after the Chernobyl accident is presented. Another table gives the Cs and Sr transfer factors soil plants for some plants. By using them estimates of future burden can be obtained.

  18. Thyroid Scan and Uptake

    Medline Plus

    Full Text Available ... type your comment or suggestion into the following text box: Comment: E-mail: Area code: Phone no: ... of a typical probe counter used for thyroid uptake exams. The patient sits with the camera directed at the neck for five minutes, and then the leg for ...

  19. Thyroid Scan and Uptake

    Science.gov (United States)

    ... type your comment or suggestion into the following text box: Comment: E-mail: Area code: Phone no: ... of a typical probe counter used for thyroid uptake exams. The patient sits with the camera directed at the neck for five minutes, and then the leg for ...

  20. Compatibility of selected plant-based shortening as lard substitute: microstructure, polymorphic forms and textural properties

    Directory of Open Access Journals (Sweden)

    N. A.M. Yanty

    2017-03-01

    Full Text Available A study was carried out to determine the compatibility of three plant-based shortening mixtures to lard shortening (LD in terms of microstructure, polymorphic forms, and textural properties. The shortenings of binary, ternary, and quaternary fat mixtures were prepared according to a standard procedure by blending mee fat (MF with palm stearin (PS in a 99:1 (w/w ratio; avocado fat (Avo with PS and cocoa butter (CB in a 84:7:9 (w/w ratio; palm oil (PO with PS, soybean oil (SBO and CB in a 38:5:52:5 (w/w ratio, respectively. The triacylglycerol composition, polymorphic forms, crystal morphology, and textural properties of the shortening were evaluated. This study found that all three plant-based shortenings and LD shortening were similar with respect to their consistency, hardness and compression and adhesiveness values. However, all plant-based shortening was found to be dissimilar to LD shortening with respect to microstructure.

  1. Micronutrient Availability in Relation to Selected Soil Properties and landscape Position in Calcareous Soils of Golpayegan

    Directory of Open Access Journals (Sweden)

    Mojtaba Fathi

    2017-02-01

    Full Text Available Introduction: Variety of soil reactions govern the distribution of metal micronutrients that includes complexation with organic and inorganic ligands, ion exchange, adsorption and desorption processes, precipitation and dissolution of solids and acid-based equilibria. The relative importance of these reactions depends on many factors such as soil physical, chemical, and mineralogical properties and the nature of metal ions. Environmental factors such as climate, physiographic position, and soil development may affect variability of some soil properties and thereby nutrient availability. The present research was conducted to find relationships between Iron, manganese, zinc, and copper availability and some major soil properties, physiographic condition and soil development. Materials and Methods: Golpayegan region is located in northwest of Isfahan province in central Iran. The mean elevation of the studied area is 1790 above sea level. Annual precipitation was about 244mm and mean monthly temperature ranges from -6 in January to 34°C in August. The soils were developed on different physiographic conditions including piedmont plains, alluvial-fan, plateaus, and flood plains belonging to Entisols and Aridisols. Soil samples (0–60 cm were collected from 98 grid points with 2000m distance in the agricultural area of Golpayegan. Particle size distribution, calcium carbonate, organic carbon, available potassium and phosphorus of the soils were measured by SWRI standard methods. Available Zn, Cu, Mn, and Fe were determined by addition of 10 g soil to 20mL 0.005M diethylentriaminepentacetic‏. The solutions were shaken for 2 h at 25°C, centrifuged, filtered, and Fe, Mn, Zn, and Cu concentrations were measured by an atomic absorption spectrophotometer. Results Discussion: Studied soils were developed on calcareous material and about 60% of samples have more than 20% of calcium carbonate. Available Fe ranged from 1.4 to 6.5 mg kg-1 (mean 15.8 mg kg-1

  2. Compatibility of selected plant-based shortening as lard substitute: microstructure, polymorphic forms and textural properties

    International Nuclear Information System (INIS)

    Yanty, N.A.M.; Marikkar, J.M.N.; Miskandar, M.S.; Bockstaele, F. Van; Dewettinck, K.; Nusantoro, B.P.

    2017-01-01

    A study was carried out to determine the compatibility of three plant-based shortening mixtures to lard shortening (LD) in terms of microstructure, polymorphic forms, and textural properties. The shortenings of binary, ternary, and quaternary fat mixtures were prepared according to a standard procedure by blending mee fat (MF) with palm stearin (PS) in a 99:1 (w/w) ratio; avocado fat (Avo) with PS and cocoa butter (CB) in a 84:7:9 (w/w) ratio; palm oil (PO) with PS, soybean oil (SBO) and CB in a 38:5:52:5 (w/w) ratio, respectively. The triacylglycerol composition, polymorphic forms, crystal morphology, and textural properties of the shortening were evaluated. This study found that all three plant-based shortenings and LD shortening were similar with respect to their consistency, hardness and compression and adhesiveness values. However, all plant-based shortening was found to be dissimilar to LD shortening with respect to microstructure. [es

  3. Biodiesel Production from Selected Microalgae Strains and Determination of its Properties and Combustion Specific Characteristics

    Directory of Open Access Journals (Sweden)

    N. Kokkinos

    2015-11-01

    Full Text Available Biofuels are gaining importance as significant substitutes for the depleting fossil fuels. Recent focus is on microalgae as the third generation feedstock. In the present research work, two indigenous fresh water and two marine Chlorophyte strains have been cultivated successfully under laboratory conditions using commercial fertilizer (Nutrileaf 30-10-10, initial concentration=70 g/m3 as nutrient source. Gas chromatographic analysis data showed that microalgae biodiesel obtained from Chlorophyte strains biomass were composed of fatty acid methyl esters. The produced microalgae biodiesel achieved a range of 2.2 - 10.6 % total lipid content and an unsaturated FAME content between 49 mol% and 59 mol%. The iodine value, the cetane number, the cold filter plugging point, the oxidative stability as well as combustion specific characteristics of the final biodiesels were determined based on the compositions of the four microalgae strains. The calculated biodiesel properties compared then with the corresponding properties of biodiesel from known vegetable oils, from other algae strains and with the specifications in the EU (EN 14214 and US (ASTM D6751 standards. The derived biodiesels from indigenous Chlorophyte algae were significantly comparable in quality with other biodiesels.

  4. On the redshift distribution and physical properties of ACT-selected DSFGs

    Science.gov (United States)

    Su, T.; Marriage, T. A.; Asboth, V.; Baker, A. J.; Bond, J. R.; Crichton, D.; Devlin, M. J.; Dünner, R.; Farrah, D.; Frayer, D. T.; Gralla, M. B.; Hall, K.; Halpern, M.; Harris, A. I.; Hilton, M.; Hincks, A. D.; Hughes, J. P.; Niemack, M. D.; Page, L. A.; Partridge, B.; Rivera, J.; Scott, D.; Sievers, J. L.; Thornton, R. J.; Viero, M. P.; Wang, L.; Wollack, E. J.; Zemcov, M.

    2017-01-01

    We present multi-wavelength detections of nine candidate gravitationally lensed dusty star-forming galaxies (DSFGs) selected at 218 GHz (1.4 mm) from the Atacama Cosmology Telescope (ACT) equatorial survey. Among the brightest ACT sources, these represent the subset of the total ACT sample lying in Herschel SPIRE fields, and all nine of the 218 GHz detections were found to have bright Herschel counterparts. By fitting their spectral energy distributions (SEDs) with a modified blackbody model with power-law temperature distribution, we find the sample has a median redshift of z=4.1^{+1.1}_{-1.0} (68 per cent confidence interval), as expected for 218 GHz selection, and an apparent total infrared luminosity of log _{10}(μ L_IR/L_{odot }) = 13.86^{+0.33}_{-0.30}, which suggests that they are either strongly lensed sources or unresolved collections of unlensed DSFGs. The effective apparent diameter of the sample is sqrt{μ }d= 4.2^{+1.7}_{-1.0} kpc, further evidence of strong lensing or multiplicity, since the typical diameter of DSFGs is 1.0-2.5 kpc. We emphasize that the effective apparent diameter derives from SED modelling without the assumption of optically thin dust (as opposed to image morphology). We find that the sources have substantial optical depth (tau = 4.2^{+3.7}_{-1.9}) to dust around the peak in the modified blackbody spectrum (λobs ≤ 500 μm), a result that is robust to model choice.

  5. The monoamine oxidase inhibition properties of selected structural analogues of methylene blue

    Energy Technology Data Exchange (ETDEWEB)

    Delport, Anzelle [Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Harvey, Brian H. [Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Pharmacology, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Petzer, Anél [Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Petzer, Jacobus P., E-mail: jacques.petzer@nwu.ac.za [Pharmaceutical Chemistry, School of Pharmacy, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa); Centre of Excellence for Pharmaceutical Sciences, North-West University, Private Bag X6001, Potchefstroom 2520 (South Africa)

    2017-06-15

    The thionine dye, methylene blue (MB), is a potent inhibitor of monoamine oxidase (MAO) A, a property that may, at least in part, mediate its antidepressant effects in humans and animals. The central inhibition of MAO-A by MB has also been linked to serotonin toxicity (ST) which may arise when MB is used in combination with serotonergic drugs. Structural analogues and the principal metabolite of MB, azure B, have also been reported to inhibit the MAO enzymes, with all compounds exhibiting specificity for the MAO-A isoform. To expand on the structure-activity relationships (SARs) of MAO inhibition by MB analogues, the present study investigates the human MAO inhibition properties of five MB analogues: neutral red, Nile blue, new methylene blue, cresyl violet and 1,9-dimethyl methylene blue. Similar to MB, these analogues also are specific MAO-A inhibitors with cresyl violet (IC{sub 50} = 0.0037 μM), Nile blue (IC{sub 50} = 0.0077 μM) and 1,9-dimethyl methylene blue (IC{sub 50} = 0.018 μM) exhibiting higher potency inhibition compared to MB (IC{sub 50} = 0.07 μM). Nile blue also represents a potent MAO-B inhibitor with an IC{sub 50} value of 0.012 μM. From the results it may be concluded that non-thionine MB analogues (e.g. cresyl violet and Nile blue) also may exhibit potent MAO inhibition, a property which should be considered when using these compounds in pharmacological studies. Benzophenoxazines such as cresyl violet and Nile blue are, similar to phenothiazines (e.g. MB), representative of high potency MAO-A inhibitors with a potential risk of ST. - Highlights: • MB analogues, cresyl violet and Nile blue, are high potency MAO-A inhibitors. • Nile blue also represents a potent MAO-B inhibitor. • Potent MAO-A inhibition should alert to potential serotonin toxicity.

  6. Isotopic composition and radiological properties of uranium in selected fuel cycles

    International Nuclear Information System (INIS)

    Fleischman, R.M.; Liikala, R.C.

    1975-04-01

    Three major topic areas are discussed: First, the properties of the uranium isotopes are defined relative to their respective roles in the nuclear fuel cycle. Secondly, the most predominant fuel cycles expected in the U. S. are described. These are the Light Water Reactor (LWR), High Temperature Gas Cooled Reactor (HTGR), and Liquid Metal Fast Breeder Reactor (LMFBR) fuel cycles. The isotopic compositions of uranium and plutonium fuels expected for these fuel cycles are given in some detail. Finally the various waste streams from these fuel cycles are discussed in terms of their relative toxicity. Emphasis is given to the high level waste streams from reprocessing of spent fuel. Wastes from the various fuel cycles are compared based on projected growth patterns for nuclear power and its various components. (U.S.)

  7. Suggested Research Method for Testing Selected Tribological Properties of Friction Components in Vehicle Braking Systems

    Directory of Open Access Journals (Sweden)

    Borawski Andrzej

    2016-09-01

    Full Text Available The braking system is one of the most important systems in any vehicle. Its proper functioning may determine the health and life the people inside the vehicle as well as other road users. Therefore, it is important that the parameters which characterise the functioning of brakes changed as little as possible throughout their lifespan. Multiple instances of heating and cooling of the working components of the brake system as well as the environment they work in may impact their tribological properties. This article describes a method of evaluating the coefficient of friction and the wear speed of abrasive wear of friction working components of brakes. The methodology was developed on the basis of Taguchi’s method of process optimization.

  8. Oxygen Sorption and Desorption Properties of Selected Lanthanum Manganites and Lanthanum Ferrite Manganites

    DEFF Research Database (Denmark)

    Nielsen, Jimmi; Skou, Eivind M.; Jacobsen, Torben

    2015-01-01

    Temperature‐programmed desorption (TPD) with a carrier gas was used to study the oxygen sorption and desorption properties of oxidation catalysts and solid‐oxide fuel cell (SOFC) cathode materials (La0.85Sr0.15)0.95MnO3+δ (LSM) and La0.60Sr0.40Fe0.80Mn0.20O3‐δ (LSFM). The powders were characterized...... by X‐ray diffractometry, atomic force microscopy (AFM), and BET surface adsorption. Sorbed oxygen could be distinguished from oxygen originating from stoichiometry changes. The results indicated that there is one main site for oxygen sorption/desorption. The amount of sorbed oxygen was monitored over...... time at different temperatures. Furthermore, through data analysis it was shown that the desorption peak associated with oxygen sorption is described well by second‐order desorption kinetics. This indicates that oxygen molecules dissociate upon adsorption and that the rate‐determining step...

  9. Mimicking the cell membrane: bio-inspired simultaneous functions with monovalent anion selectivity and antifouling properties of anion exchange membrane

    Science.gov (United States)

    Zhao, Yan; Liu, Huimin; Tang, Kaini; Jin, Yali; Pan, Jiefeng; der Bruggen, Bart Van; Shen, Jiangnan; Gao, Congjie

    2016-11-01

    A new bio-inspired method was applied in this study to simultaneously improve the monovalent anion selectivity and antifouling properties of anion exchange membranes (AEMs). Three-layer architecture was developed by deposition of polydopamine (PDA) and electro-deposition of N-O-sulfonic acid benzyl chitosan (NSBC). The innermost and outermost layers were PDA with different deposition time. The middle layer was prepared by NSBC. Fourier transform infrared spectroscopy and scanning electron microscopy confirmed that PDA and NSBC were successfully modified on the surfaces of AEMs. The contact angle of the membranes indicated an improved hydrophilicity of the modified membranes. A series of electrodialysis experiments in which Cl-/SO42- separation was studied, demonstrating the monovalent anion selectivity of the samples. The Cl-/SO42- permselectivity of the modified membranes can reach up to 2.20, higher than that of the commercial membrane (only 0.78) during 90 minutes in electrodialysis (ED). The increase value of the resistance of the membranes was also measured to evaluate the antifouling properties. Sodium dodecyl benzene sulfonate (SDBS) was used as the fouling material in the ED process and the membrane area resistance of modified membrane increase value of was only 0.08 Ωcm2 30 minutes later.

  10. Mimicking the cell membrane: bio-inspired simultaneous functions with monovalent anion selectivity and antifouling properties of anion exchange membrane

    Science.gov (United States)

    Zhao, Yan; Liu, Huimin; Tang, Kaini; Jin, Yali; Pan, Jiefeng; der Bruggen, Bart Van; Shen, Jiangnan; Gao, Congjie

    2016-01-01

    A new bio-inspired method was applied in this study to simultaneously improve the monovalent anion selectivity and antifouling properties of anion exchange membranes (AEMs). Three-layer architecture was developed by deposition of polydopamine (PDA) and electro-deposition of N-O-sulfonic acid benzyl chitosan (NSBC). The innermost and outermost layers were PDA with different deposition time. The middle layer was prepared by NSBC. Fourier transform infrared spectroscopy and scanning electron microscopy confirmed that PDA and NSBC were successfully modified on the surfaces of AEMs. The contact angle of the membranes indicated an improved hydrophilicity of the modified membranes. A series of electrodialysis experiments in which Cl−/SO42− separation was studied, demonstrating the monovalent anion selectivity of the samples. The Cl−/SO42− permselectivity of the modified membranes can reach up to 2.20, higher than that of the commercial membrane (only 0.78) during 90 minutes in electrodialysis (ED). The increase value of the resistance of the membranes was also measured to evaluate the antifouling properties. Sodium dodecyl benzene sulfonate (SDBS) was used as the fouling material in the ED process and the membrane area resistance of modified membrane increase value of was only 0.08 Ωcm2 30 minutes later. PMID:27853255

  11. The interaction properties of the human Rab GTPase family--comparative analysis reveals determinants of molecular binding selectivity.

    Directory of Open Access Journals (Sweden)

    Matthias Stein

    Full Text Available Rab GTPases constitute the largest subfamily of the Ras protein superfamily. Rab proteins regulate organelle biogenesis and transport, and display distinct binding preferences for effector and activator proteins, many of which have not been elucidated yet. The underlying molecular recognition motifs, binding partner preferences and selectivities are not well understood.Comparative analysis of the amino acid sequences and the three-dimensional electrostatic and hydrophobic molecular interaction fields of 62 human Rab proteins revealed a wide range of binding properties with large differences between some Rab proteins. This analysis assists the functional annotation of Rab proteins 12, 14, 26, 37 and 41 and provided an explanation for the shared function of Rab3 and 27. Rab7a and 7b have very different electrostatic potentials, indicating that they may bind to different effector proteins and thus, exert different functions. The subfamily V Rab GTPases which are associated with endosome differ subtly in the interaction properties of their switch regions, and this may explain exchange factor specificity and exchange kinetics.We have analysed conservation of sequence and of molecular interaction fields to cluster and annotate the human Rab proteins. The analysis of three dimensional molecular interaction fields provides detailed insight that is not available from a sequence-based approach alone. Based on our results, we predict novel functions for some Rab proteins and provide insights into their divergent functions and the determinants of their binding partner selectivity.

  12. Electrodialytic removal of nitrate from pineapple juice: effect on selected physicochemical properties, amino acids, and aroma components of the juice.

    Science.gov (United States)

    Ackarabanpojoue, Yuwadee; Chindapan, Nathamol; Yoovidhya, Tipaporn; Devahastin, Sakamon

    2015-05-01

    This study aimed at investigating the effect of nitrate removal from pineapple juice by electrodialysis (ED) on selected properties of the ED-treated juice. Single-strength pineapple juice with reduced pulp content was treated by ED to reduce the nitrate concentration to 15, 10, or 5 ppm. After ED, the removed pulp was added to the ED-treated juice and its properties, including electrical conductivity, acidity, pH, total soluble solids (TSS), color, amino acids, and selected aroma compounds, were determined and compared with those of the untreated juice. ED could reduce the nitrate content of 1 L of pineapple juice from an initial value of 50 ppm to less than 5 ppm within 30 min. A significant decrease in the electrical conductivity, acidity, pH, TSS, and yellowness, but a significant increase in the lightness, of the juice was observed upon ED. Concentrations of almost all amino acids of the ED-treated juice significantly decreased. The concentrations of 8 major compound contributors to the pineapple aroma also significantly decreased. Adding the pulp back to the ED-treated juice increased the amino acids concentrations; however, it led to a significant decrease in the concentrations of the aroma compounds. © 2015 Institute of Food Technologists®

  13. Awareness and Uptake of Human Papilloma Virus Vaccination and ...

    African Journals Online (AJOL)

    Awareness and Uptake of Human Papilloma Virus Vaccination and Cervical ... Multistage sampling was used to select 400 female undergraduate students that ... None of the respondents knew that sexual exposure to HPV could result in ...

  14. Microstructure and mechanical properties of Al-12Si produced by selective laser melting

    Science.gov (United States)

    Fefelov, A. S.; Merkushev, A. G.; Chikova, O. A.

    2017-10-01

    Al-12Si specimens are produced by selective laser melting (SLM) from gas atomized powders. Installation for the production of powder is original. All specimens were prepared using the EOSINT M 280 device. A fine cellular structure is observed with residual free Si along the cellular boundaries. Room temperature tensile tests reveal remarkable mechanical behavior: the samples show yield and tensile strengths of about 102 MPa and 425 MPa, respectively, along with fracture strain of 12%. The study of crack surface morphology was shown by the example of a sample. Except the spherical pores, the interface of the molten pool also appears on the fracture surface, which indicates a mixture of fragile and ductile fracture. Additionally, the agglomerated silicon group appears also on the fracture surface.

  15. On the Redshift Distribution and Physical Properties of ACT-Selected DSFGs

    Science.gov (United States)

    Su, T.; Marriage, T. A.; Asboth, V.; Baker, A. J.; Bond, J. R.; Crichton, D.; Devlin, M. J.; Dunner, R.; Farrah, D.; Frayer, D. T.; hide

    2016-01-01

    We present multi-wavelength detections of nine candidate gravitationally-lensed dusty starforming galaxies (DSFGs) selected at 218 GHz (1.4 mm) from the ACT equatorial survey. Among the brightest ACT sources, these represent the subset of the total ACT sample lying in Herschel SPIRE fields, and all nine of the 218 GHz detections were found to have bright Herschel counterparts. By fitting their spectral energy distributions (SEDs) with a modified blackbody model with power-law temperature distribution, we find the sample has a median redshift of 4.1 (+ 1.1, -10) (68 percent confidence interval), as expected for 218 GHz selection and an apparent total infrared luminosity of log 10(uL(sub IR)/solar luminosity) = 13.86(+0.33, -0.30), which suggests that they are either strongly lensed sources or unresolved collections of unlensed DSFGs. The effective apparent diameter of the sample is square root of mu d = 4.2 (+ 1.7, -1.0) kpc, further evidence of strong lensing of multiplicity, since the typical diameter of dusty star-forming galaxies is 1.0-2.5 kpc. We emphasize that the effective apparent diameter derives from SED modeling without the assumption of opticaly thin dust (as opposed to image morphology). We find that the sources have substantial optical depth (tau = (4.2+, -1.9) of dust around the peak in the modified blackbody spectrum (lambda obs is less than 500 micrometers), a result that is robust to model choice.

  16. Host Galaxy Properties of the Swift BAT Ultra Hard X-Ray Selected AGN

    Science.gov (United States)

    Koss, Michael; Mushotzky, Richard; Veilleux, Sylvain; Winter, Lisa M.; Baumgartner, Wayne; Tueller, Jack; Gehrels, Neil; Valencic, Lynne

    2011-01-01

    We have assembled the largest sample of ultra hard X-ray selected (14-195 keV) AGN with host galaxy optical data to date, with 185 nearby (zBAT) sample. The BAT AGN host galaxies have intermediate optical colors (u -- r and g -- r) that are bluer than a comparison sample of inactive galaxies and optically selected AGN from the Sloan Digital Sky Survey (SDSS) which are chosen to have the same stellar mass. Based on morphological classifications from the RC3 and the Galaxy Zoo, the bluer colors of BAT AGN are mainly due to a higher fraction of mergers and massive spirals than in the comparison samples. BAT AGN in massive galaxies (log Stellar Mass >10.5) have a 5 to 10 times higher rate of spiral morphologies than in SDSS AGN or inactive galaxies. We also see enhanced far-IR emission in BAT AGN suggestive of higher levels of star formation compared to the comparison samples. BAT AGN are preferentially found in the most massive host galaxies with high concentration indexes indicative of large bulge-to-disk ratios and large supermassive black holes. The narrow-line (NL) BAT AGN have similar intrinsic luminosities as the SDSS NL Seyferts based on measurements of [O III] Lambda 5007. There is also a correlation between the stellar mass and X-ray emission. The BAT AGN in mergers have bluer colors and greater ultra hard X-ray emission compared to the BAT sample as whole. In agreement with the Unified Model of AGN, and the relatively unbiased nature of the BAT sources, the host galaxy colors and morphologies are independent of measures of obscuration such as X-ray column density or Seyfert type. The high fraction of massive spiral galaxies and galaxy mergers in BAT AGN suggest that host galaxy morphology is related to the activation and fueling of local AGN.

  17. Evaluation of the mechanical properties and porcelain bond strength of cobalt-chromium dental alloy fabricated by selective laser melting.

    Science.gov (United States)

    Wu, Lin; Zhu, Haiting; Gai, Xiuying; Wang, Yanyan

    2014-01-01

    Limited information is available regarding the microstructure and mechanical properties of dental alloy fabricated by selective laser melting (SLM). The purpose of this study was to evaluate the mechanical properties of a cobalt-chromium (Co-Cr) dental alloy fabricated by SLM and to determine the correlation between its microstructure and mechanical properties and its porcelain bond strength. Five metal specimens and 10 metal ceramic specimens were fabricated to evaluate the mechanical properties of SLM Co-Cr dental alloy (SLM alloy) with a tensile test and its porcelain bond strength with a 3-point bending test. The relevant properties of the SLM alloy were compared with those of the currently used Co-Cr dental alloy fabricated with conventional cast technology (cast alloy). The Student t test was used to compare the results of the SLM alloy and the cast alloy (α=.05). The microstructure of the SLM alloy was analyzed with a metallographic microscope; the metal ceramic interface of the SLM porcelain bonded alloy was studied with scanning electron microscopy, energy dispersive x-ray spectroscopy, and an electron probe microanalyzer. Both the mean (standard deviation) yield strength (884.37 ± 8.96 MPa) and tensile strength (1307.50 ±10.65 MPa) of the SLM alloy were notably higher than yield strength (568.10 ± 30.94 MPa) and tensile strength (758.73 ± 25.85 MPa) of the currently used cast alloy, and the differences were significant (P.05). Microstructure analysis suggested that the SLM alloy had a dense and obviously orientated microstructure, which led to excellent mechanical properties. Analysis from scanning electron microscopy, energy dispersive x-ray spectroscopy, and the electron probe microanalyzer indicated that the SLM alloy had an intermediate layer with elemental interpenetration between the alloy and the porcelain, which resulted in an improved bonding interface. Compared with the currently used cast alloy, SLM alloy possessed improved mechanical

  18. The role intuitive decision making plays in project selection in the residential property market: a case study of a medium sized

    OpenAIRE

    Ryan, Diarmuid

    2013-01-01

    non-peer-reviewed This thesis addresses the role of intuition in project selection in residential property development. The paper provides a comprehensive review of existing literature in relation to project selection and decision making. In addition, the examination of the project files of M.A. Ryan & Sons Ltd., a medium sized property development company, has enabled a case study to be carried out on three projects carried out by the organisation. Through the case study, t...

  19. Characterisation and biochemical properties of predominant lactic acid bacteria from fermenting cassava for selection as starter cultures.

    Science.gov (United States)

    Kostinek, M; Specht, I; Edward, V A; Pinto, C; Egounlety, M; Sossa, C; Mbugua, S; Dortu, C; Thonart, P; Taljaard, L; Mengu, M; Franz, C M A P; Holzapfel, W H

    2007-03-20

    A total of 375 lactic acid bacteria were isolated from fermenting cassava in South Africa, Benin, Kenya and Germany, and were characterised by phenotypic and genotypic tests. These could be divided into five main groups comprising strains of facultatively heterofermentative rods, obligately heterofermentative rods, heterofermentative cocci, homofermentative cocci and obligately homofermentative rods, in decreasing order of predominance. Most of the facultatively heterofermentative rods were identified by phenotypic tests as presumptive Lactobacillus plantarum-group strains, which also comprised the most predominant bacteria (54.4% of strains) isolated in the study. The next predominant group of lactic acid bacteria (14.1% of total isolates) consisted of obligately heterofermentative rods belonging either to the genus Lactobacillus or Weissella, followed by the heterofermentative cocci (13.9% of isolates) belonging to the genera Weissella or Leuconostoc. Homofermentative cocci were also isolated (13.3% of isolates). Biochemical properties such as production of alpha-amylase, beta-glucosidase, tannase, antimicrobials (presumptive bacteriocin and H(2)O(2)-production), acidification and fermentation of the indigestible sugars raffinose and stachyose, were evaluated in vitro for selection of potential starter strains. A total of 32 strains with one or more desirable biochemical properties were pre-selected and identified using rep-PCR fingerprinting in combination with 16S rRNA sequencing of representative rep-PCR cluster isolates. Of these strains, 18 were identified as L. plantarum, four as Lactobacillus pentosus, two each as Leuconostoc fallax, Weissella paramesenteroides and Lactobacillus fermentum, one each as Leuconostoc mesenteroides subsp. mesenteroides and Weissella cibaria, while two remained unidentified but could be assigned to the L. plantarum-group. These strains were further investigated for clonal relationships, using RAPD-PCR with three primers, and of

  20. Variations of selected soil properties in the grass fields invaded and uninvaded by invasive goldenrod (Solidago canadensis L.

    Directory of Open Access Journals (Sweden)

    Baranová Beáta

    2017-06-01

    Full Text Available Although the invasion of exotic plants has been recognised as the serious cause of the biodiversity loss and natural habitats degradation and threat to the ecosystems functions, just the little attention has been paid to the potential impacts of the goldenrod invasion on the soil properties. Equally, currently obtained results are contrary and ambiguous. We tested whether the grass fields invaded and uninvaded by Canadian goldenrod (Solidago canadensis L. differ in pH, soil moisture, organic carbon (Cox, humus and P, K and Mg contents and related the variations to the chosen environmental variables. We did not find significant distinctions of the studied types of habitats in the selected physico-chemical soil properties as well as the relation between the goldenrod invasion and the changes in soil properties. Nevertheless, whereas the soil reaction, soil moisture and Mg content were higher in the invaded soils, the Cox, humus and P and K contents were higher in the uninvaded ones. Doubtless, further attention need to be paid to this problem.

  1. Evaluation of Relationships between Drilling Rate Index and Physical and Strength Properties of Selected Rock Units of Pakistan

    International Nuclear Information System (INIS)

    Shafique, U.; Abu Bakar, M. Z.

    2015-01-01

    Fifteen selected rock types collected from different formations of Pakistan were subjected to Drilling Rate Index (DRI) tests and various physical and strength properties tests including, porosity (n), density, primary wave velocity (V/sub p/), uniaxial compressive strength (sigma/sub c/), Brazilian tensile strength (sigma/sub t/) and Schmidt hammer rebound number (R/sub n/),. Prior knowledge of the drill ability of rocks and their physico-mechanical properties plays a decisive role in planning and design of rock drilling and excavation processes. DRI tests developed by NTNU/SINTEF are in use by the industry since 1960s and have proved very successful in estimation of the boreability of rocks, but no such work has been reported for Pakistani rocks to date. Reasonable correlations were found between the DRI and the properties of the tested rocks. The trends shown in this paper are of interest for the machine manufacturers and operators working on various projects involving the use of drilling machines and other mechanical excavators. (author)

  2. Contact-Engineered Electrical Properties of MoS2 Field-Effect Transistors via Selectively Deposited Thiol-Molecules.

    Science.gov (United States)

    Cho, Kyungjune; Pak, Jinsu; Kim, Jae-Keun; Kang, Keehoon; Kim, Tae-Young; Shin, Jiwon; Choi, Barbara Yuri; Chung, Seungjun; Lee, Takhee

    2018-05-01

    Although 2D molybdenum disulfide (MoS 2 ) has gained much attention due to its unique electrical and optical properties, the limited electrical contact to 2D semiconductors still impedes the realization of high-performance 2D MoS 2 -based devices. In this regard, many studies have been conducted to improve the carrier-injection properties by inserting functional paths, such as graphene or hexagonal boron nitride, between the electrodes and 2D semiconductors. The reported strategies, however, require relatively time-consuming and low-yield transfer processes on sub-micrometer MoS 2 flakes. Here, a simple contact-engineering method is suggested, introducing chemically adsorbed thiol-molecules as thin tunneling barriers between the metal electrodes and MoS 2 channels. The selectively deposited thiol-molecules via the vapor-deposition process provide additional tunneling paths at the contact regions, improving the carrier-injection properties with lower activation energies in MoS 2 field-effect transistors. Additionally, by inserting thiol-molecules at the only one contact region, asymmetric carrier-injection is feasible depending on the temperature and gate bias. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Effect of Heat Treatment on the Properties of CoCrMo Alloy Manufactured by Selective Laser Melting

    Science.gov (United States)

    Guoqing, Zhang; Junxin, Li; Xiaoyu, Zhou; Jin, Li; Anmin, Wang

    2018-05-01

    To obtain medical implants with better mechanical properties, it is necessary to conduct studies on the heat treatment process of the selective laser melting (SLM) manufacturing parts. The differential scanning calorimetry method was used to study the heat treatment process of the phase transition of SLM CoCrMo alloy parts. The tensile properties were tested with a tensile test machine, the quantity of carbide precipitated after heat treatment was measured by energy-dispersive x-ray spectroscopy, and the tensile fracture morphology of the parts was investigated using SEM. The obtained results were: Mechanical properties in terms of elongation and tensile strength of CoCrMo alloy manufactured by SLM that had been heat-treated at 1200 °C for 2 h followed by cooling with water were not only higher than the national standard but also higher than the experimental results of the same batch of castings. The mechanism of fracture of parts manufactured by SLM without heat treatment was brittle fracture, whereas parts which had been heat-treated at 1200 °C for 2 h combined with water cooling and at 1200 °C for 1 h with furnace cooling suffered ductile fracture. This study provides the basis for defining the applications for which CoCrMo alloys manufactured by SLM are suitable within the field of medical implants.

  4. The selection and properties of epoxide resins used for the insulation of magnet systems in radiation environments

    International Nuclear Information System (INIS)

    Phillips, D.C.; Scott, J.M.; Goebel, K.; Schoenbacher, H.

    1981-01-01

    Laboratory tests have been carried out on five types of epoxy resins - four based on bisphenol A, one on hydantoin-bisphenol A - applicable in the construction of large magnet coils. Two of the resin compositions have already been used in large quantities as insulating material for magnets at the European Organization for Nuclear Research (CERN); the others were selected for comparison according to their good radiation resistance, good initial mechanical properties, and optimal properties for vacuum impregnation. Three types of tests are discussed in detail: creep, crack propagation (as a measure of toughness), and radiation resistance. The results show that the resin composition with hydantoin exhibits the best resistance to crack propagation but, on the other hand, the lowest resistance to ionizing radiation, and can therefore not be recommended for use in a radiation environment. Among the other materials based on biosphenol A, better toughness values were obtained with lower-cross-linked resin systems, whereas the radiation resistance is better for highly-cross-linked materials. It is concluded that a reasonable compromise combining good processing and operational properties with sufficiently high radiation resistance is obtained with a standard epoxy-resin-type bisphenol A with a specially formulated anhydride hardener and an amine-substituted phenol-type accelerator. (orig.)

  5. Mechanical properties' improvement of a tricalcium phosphate scaffold with poly-l-lactic acid in selective laser sintering

    International Nuclear Information System (INIS)

    Liu, Defu; Zhuang, Jingyu; Shuai, Cijun; Peng, Shuping

    2013-01-01

    To improve the mechanical properties of a scaffold fabricated via selective laser sintering (SLS), a small amount (0.5–3 wt%) of poly-l-lactic acid (PLLA) is added to the β-tricalcium phosphate (β-TCP) powder. The fracture toughness of the scaffold prepared with the mixture powder containing 1 wt% PLLA increases by 18.18% and the compressive strength increases by 4.45% compared to the scaffold prepared from the β-TCP powder. The strengthening and toughening is related to the enhancement of β-TCP sintering characteristics via introducing a transient liquid phase in SLS. Moreover, the microcracks caused by the volume expansion due to the β–α phase transformation of TCP are reduced because of the PLLA inhibition function on the phase transformation. However, PLLA additive above 1 wt% would lead to a PLLA residue which will decrease the mechanical properties. The experimental results show that PLLA is an effective sintering aid to improve the mechanical properties of a TCP scaffold. (paper)

  6. Development of a material property database on selected ceramic matrix composite materials

    Science.gov (United States)

    Mahanta, Kamala

    1996-01-01

    Ceramic Matrix Composites, with fiber/whisker/particulate reinforcement, possess the attractive properties of ceramics such as high melting temperature, high strength and stiffness at high temperature, low density, excellent environmental resistance, combined with improved toughness and mechanical reliability. These unique properties have made these composites an enabling technology for thermomechanically demanding applications in high temperature, high stress and aggressive environments. On a broader scale, CMC's are anticipated to be applicable in aircraft propulsion, space propulsion, power and structures, in addition to ground based applications. However, it is also true that for any serious commitment of the material toward any of the intended critical thermo-mechanical applications to materialize, vigorous research has to be conducted for a thorough understanding of the mechanical and thermal behavior of CMC's. The high technology of CMC'S is far from being mature. In view of this growing need for CMC data, researchers all over the world have found themselves drawn into the characterization of CMC's such as C/SiC, SiC/SiC, SiC/Al203, SiC/Glass, SiC/C, SiC/Blackglas. A significant amount of data has been generated by the industries, national laboratories and educational institutions in the United States of America. NASA/Marshall Space Flight Center intends to collect the 'pedigreed' CMC data and store those in a CMC database within MAPTIS (Materials and Processes Technical Information System). The task of compilation of the CMC database is a monumental one and requires efforts in various directions. The project started in the form of a summer faculty fellowship in 1994 and has spilled into the months that followed and into the summer faculty fellowship of 1995 and has the prospect of continuing into the future for a healthy growth, which of course depends to a large extent on how fast CMC data are generated. The 10-week long summer fellowship has concentrated

  7. Effect of selected Hofmeister salts on textural and rheological properties of nonfat cheese.

    Science.gov (United States)

    Stankey, J A; Johnson, M E; Lucey, J A

    2011-09-01

    Three Hofmeister salts (HS; sodium sulfate, sodium thiocyanate, and sodium chloride) were evaluated for their effect on the textural and rheological properties of nonfat cheese. Nonfat cheese, made by direct acidification, were sliced into discs (diameter=50 mm, thickness=2 mm) and incubated with agitation (6 h at 22°C) in 50 mL of a synthetic Cheddar cheese aqueous phase buffer (pH 5.4). The 3 HS were added at 5 concentrations (0.1, 0.25, 0.5, 0.75, and 1.0 M) to the buffer. Post-incubation, cheese slices were air dried and equilibrated in air-tight bags for 18 h at 5°C before analysis. Small amplitude oscillatory rheology properties, including the dynamic moduli and loss tangent, were measured during heating from 5 to 85°C. Hardness was determined by texture profile analysis. Acid-base buffering was performed to observe changes in the indigenous insoluble (colloidal) calcium phosphate (CCP). Moisture content decreased with increasing HS concentration. Cheeses incubated in high concentrations of SCN(-) softened earlier (i.e., loss tangent=1) compared with other HS treatments. Higher melting temperature values were observed for cheeses incubated in high concentrations of SO(4)(2-). Hardness decreased in cheeses incubated in buffers with high concentrations of SCN(-). The indigenous CCP profile of nonfat cheese was not greatly affected by incubation in Cl(-) or SCN(-), whereas buffers with high concentrations of SO(4)(2-) reduced the acid-base buffering contributed by CCP. The use of high concentrations (1.0M) of SCN(-) for incubation of cheeses resulted in a softer protein matrix at high temperatures due to the chaotropic effect of SCN(-), which weakened hydrophobic interactions between CN. Cheese samples incubated in 1.0M SO(4)(2-) buffers exhibited a stiffer protein matrix at high temperatures due to the kosmotropic effect of SO(4)(2-), which helped to strengthen hydrophobic interactions in the proteins during the heating step. This study showed that HS

  8. The effect of addition of selected carrageenans on viscoelastic properties of model processed cheese spreads

    Directory of Open Access Journals (Sweden)

    Michaela Černíková

    2007-01-01

    Full Text Available The effect of 0.25% w/w κ-carrageenan and ι‑carrageenan on viscoelastic properties of processed cheese were studied using model samples containing 40% w/w dry matter and 45 and 50% w/w fat in dry matter. Experimental samples of processed cheese were evaluated after 14 days of storage at the temperature of 6 ± 2 °C. Basic parameters of processed cheese samples under study (i.e. their dry matter content and pH were not different (P ≥ 0.05. There were no statistically significant differences in values of storage modulus G´ [Pa], loss modulus G'' [Pa] and tangent of phase shift angle tan δ [-] for the reference frequency of 1 Hz between processed cheese with κ‑carrageenan applied in the form of powder and in the form of aqueous dispersion (P ≥ 0.05. The addition of 0.25% w/w κ‑carrageenan and ι‑carrageenan (in the powder form resulted in an increase in storage (G´ and loss (G'' moduli and a decrease in values of tan δ (P < 0.05. As compared with control (i.e. without added carrageenans, samples of processed cheese became firmer. Iota-carrageenan added in the powder form in concentration of 0.25% w/w showed a more intensive effect on the increase in firmness of processed cheese under study than κ‑carrageenan (P < 0.05.

  9. Influence of Temperature and Storing Time on Selected Red Wine Physical Properties

    Directory of Open Access Journals (Sweden)

    Peter Hlaváč

    2016-01-01

    Full Text Available Presented article is focused on red wine rheological and thermal properties. Effects of temperature and short term storage on density, rheological parameters and thermal parameters were investigated. First measurement was done at the beginning of storage and then the same sample was measured again after one week of storing. Density was measured by densimeter Mettler Toledo DM 40 at different temperatures. For dynamic viscosity measurement was used rotational viscometer Anton Paar DV-3P. The kinematic viscosity and fluidity were determined according to the definitions. Thermal parameters were measured by instrument Isomet 2104. Temperature dependencies of wine dynamic and kinematic viscosity had decreasing exponential shape and temperature dependencies of fluidity had an increasing exponential shape. Temperature dependencies of red wine thermal conductivity and diffusivity had increasing linear character. Decreasing polynomial functions were obtained for temperature dependencies of red wine density. The values of dynamic and kinematic viscosity, thermal conductivity and diffusivity, and density of red wine were a little bit higher after short term storing, which can be expressed by changed amount of water caused by evaporation. Due to the same reasons were values of fluidity little bit lower after storage.

  10. Physical properties and chemical durability of selected zirconia containing silicate glasses

    Directory of Open Access Journals (Sweden)

    ELEONÓRA GAŠPÁREKOVÁ

    2011-12-01

    Full Text Available Density, thermal expansion, glass transition temperature, refractive index, molar refractivity and chemical durability of five- and six-component glasses with as weighted composition xNa2O·(15-xK2O·yCaO∙(10-yZnO∙zZrO2∙(75-zSiO2 (x = 0, 7.5, 15; y = 0, 5, 10; z = 5, 7 were measured. The obtained experimental data were merged together with the previous results obtained for analogous glasses with lower zirconia content. The full set of glasses enabled the quantitative statistical estimation of possible mixed-oxide effects. The results of the multilinear regression analysis pointed out the ideal behavior of molar volume and molar refractivity. The strongest influence of mutual oxide interactions was found for chemical durability and glass transition temperature. The regression analysis of compositional dependence of metastable melt thermal expansion coefficient practically failed. The need of property-composition study based on the thermodynamic model was pointed out. Qualitatively the obtained results confirmed those previously obtained for the analogous glasses with zirconia content reaching up to 3 mol. %.

  11. Synthesis, characterization and magnetic properties of selected Laves and MAX phases

    International Nuclear Information System (INIS)

    Hamm, Christin Maria

    2017-01-01

    In this work the rare-earth free Laves phases Ti 2 M 3 Si with M = Mn, Fe, Co, Ni were synthesized by microwave heating and were structurally and magnetically characterized. Furthermore, the solid solution Ti 2 (Co 1-x Fe x ) 3 Si was synthesized by arc melting and spark plasma sintering, as well as their magnetic behavior was studied. In addition to the Laves phases, the focus was on the synthesis and characterization of aluminum-based MAX phases. For the first time the ternary carbides were prepared by microwave heating. The phase-pure representation of MAX phases was particularly challenging for synthetic solid-state chemistry. The susceptor-assisted microwave heating allows the synthesis of high-quality samples, which was shown in this work on M 2 AlC (M = Ti, V, Cr) and V 4 AlC 3 . Furthermore, for the first time, the doping of these materials with Mn and Fe was successful. In addition to the structural characterization of the new phases, the microstructure and magnetic properties are discussed in this work. Using these doped compounds as well as the compound V 4 AlC 3 , it has been shown that field-activated synthesis, particularly susceptor-assisted microwave heating, are a very good synthesis method for compounds which are hard or sometimes not synthesized by conventional methods.

  12. The slag original from the process of sewage sludge incineration selected properties characteristic

    Science.gov (United States)

    Głowacka, Anna; Rucińska, Teresa; Kiper, Justyna

    2017-11-01

    This work characterizes the physical and chemical properties of slag from combustion of municipal sewage sludge in "Pomorzany" waste treatment plant in Szczecin. The technology of sludge management is based on drying the sludge in low-temperature belt driers, to a content level of at least 90%, dry mass., and then burning in a grate boiler with mobile grate. The research of the slag resulting from combustion of municipal sewage sludge was conducted using reference methods, presenting images from a scanning electron microscope. The tested waste contained from 16.300 to 23.150% P2O5 completely soluble in strong acids, pH 8.03, mineral substance 98.73% dry mass. The content of heavy metals did not exceed the permissible amount specified in the Regulation of the Minister of Agriculture and Rural Development of 18 June 2008 on the implementation of certain provisions of the Act on fertilizers and fertilization (Journal of Laws of 2008 No. 119, item. 765). The screening trials showed that 48.4% are fractions of 630 µm-1.25 mm. The results show that the waste code 19 01 12 may be used as: alternative source of phosphorus for direct application to soil treatment, for production of organic - mineral fertilizers and as construction aggregate for production of concrete mortars.

  13. The effect of environmental factors on selected mechanical properties of zirconium dioxide

    Science.gov (United States)

    Wirwicki, W.; Andrzejewska, A.; Andryszczyk, M.; Siemianowski, P.

    2018-04-01

    In many centers around the world, research studies are carried out on the mechanical strength of dental materials and glued joints. A literature review shows the variety of testing techniques related to analyzing the strength and durability of the material itself and the glued joints. In dental ceramics, zirconium dioxide is most often used as a base material, and chemically it consists of 97% ZrO2 and 3% Y2O3. This study was to determine the mechanical properties of zirconium dioxide under different environmental conditions. The material is used for the production of dental crowns and tooth bridges in the CAD/CAM technology. This medium is currently one of the most advanced-generation materials used for prosthetic and implant restorations. They were then subjected to a three-point bending test on the Instron ElektroPlus E3000 durability machine. Storage conditions and time have a positive influence on reducing variation in zirconium resistance for active forces and destructive stresses.

  14. The sensitivity and selectivity properties of a fluorescence sensor based on quinoline-Bodipy

    Energy Technology Data Exchange (ETDEWEB)

    Nuri Kursunlu, Ahmed, E-mail: ankursunlu@gmail.com; Guler, Ersin

    2014-01-15

    A novel florescence sensor (Q-BODIPY) based on quinoline-Bodipy (quinoline-boradiazaindacene) was prepared by ‘click chemistry’ in several stages. The sensing actions of Q-BODIPY were confirmed by UV–vis titration, emission and excitation spectroscopic studies in presence of Mn{sup 2+}, Co{sup 2+}, Ni{sup 2+}, Cu{sup 2+}, Zn{sup 2+}, Cd{sup 2+}, Sn{sup 2+}, Hg{sup 2+}, Pb{sup 2+}, La{sup 3+}, Ga{sup 3+}, Er{sup 3+} and Yb{sup 3+} ions in methanol:H{sub 2}O (1:1) medium. Whereas some metal ions can only cause quenching effect on the fluorescence intensity of Q-BODIPY, some of them show an increase in fluorescence intensity. The stoichiometry of host–guest complexes formed was determined by Job′s plot method. The binding constants were calculated by Stern–Volmer method. As a fluorescence sensor, Q-BODIPY shows the best selectivity performance against Zn{sup 2+} ions in according to all spectroscopic data. -- Highlights: • Q-BODIPY prepared by several techniques shows a fluorescent behavior toward p, d and f block metal ions. • Q-BODIPY has both a more sensitivity and more effective ability for the detection of Zn(II) ion. • The synthesis strategies to produce Bodipy′s with metal coordinating offer a new approach for the design of novel fluorescence sensors.

  15. Selective Growth and SERS Property of Gold Nanoparticles on Amorphized Silicon Surface

    International Nuclear Information System (INIS)

    Matsuoka, T; Nishi, M; Sakakura, M; Shimotsuma, Y; Miura, K; Hirao, K

    2011-01-01

    We have fabricated gold patterns on a silicon substrate by a simple three-step method using a focused ion beam (FIB). The obtained gold patterns consisted of a large number of gold nanoparticles which grew selectively on the preprocessed silicon surface from an Au ion-containing solution dropped on the substrate. The solution was prepared by reacting HAuCl 4 aqueous solution with (3-mercaptopropyl)trimethoxysilane (MPTMS). It was found that the size and shape of the precipitating gold nanoparticles is controllable by changing the mixing ratio between HAuCl 4 aqueous solution and MPTMS. Additionally, we confirmed that the fabricated gold structures were surface enhanced Raman scattering (SERS)-active; the enhanced Raman peaks of rhodamin 6G (R6G) were detected on the fabricated gold structures, whereas no peak was detected on the alternative silicon surface. We also demonstrated the gold patterning using a femtosecond laser instead of an FIB. We believe that our method is a favorable candidate for fabricating SERS-active substrates, since the substrates can be prepared very simply and flexibly.

  16. Enkephalin dipeptidyl carboxypeptidase (enkephalinase) activity: selective radioassay, properties, and regional distribution in human brain

    International Nuclear Information System (INIS)

    Llorens, C.; Malfroy, B.; Schwartz, J.C.; Gacel, G.; Roques, B.P.; Roy, J.; Morgat, J.L.; Javoy-Agid, F.; Agid, Y.

    1982-01-01

    The compound [ 3 H-Tyr 1 ,D-Ala 2 ,Leu-OH 5 ]enkephalin has been synthesised as a potentially selective substrate for enkephalin dipeptidyl carboxypeptidase (enkephalinase) activity in brain. Incubations in the presence of homogenates and particulate fractions from rodent and human brain result in the formation of [ 3 H]Tyr-D-Ala-Gly, which can be conveniently isolated by polystyrene bead column chromatography. The enzyme activity responsible for the hydrolysis of the Gly 3 -Phe 4 amide bond of this substrate displays close resemblance to that hydrolysing the natural enkephalins at the same level. In addition, enkephalinase activity characterised in postmortem human brain is closely similar to that in rodent brain, with regard to optimal pH and apparent affinities of various substrates and inhibitors, including the potent compound thiorphan. Enkephalinase activity is distributed in a highly heterogeneous fashion among regions of human brain, the highest levels being found in globus pallidus and pars reticulata of the substantia nigra. This distribution is poorly correlated with that of opiate receptor binding sites but displays some resemblance to that of reported Met 5 -enkephalin levels. (author)

  17. Effect of strain rate and temperature on mechanical properties of selected building Polish steels

    Directory of Open Access Journals (Sweden)

    Moćko Wojciech

    2015-01-01

    Full Text Available Currently, the computer programs of CAD type are basic tool for designing of various structures under impact loading. Application of the numerical calculations allows to substantially reduce amount of time required for the design stage of such projects. However, the proper use of computer aided designing technique requires input data for numerical software including elastic-plastic models of structural materials. This work deals with the constitutive model developed by Rusinek and Klepaczko (RK applied for the modelling of mechanical behaviour of selected grades structural St0S, St3SX, 18GS and 34GS steels and presents here results of experimental and empirical analyses to describe dynamic elastic-plastic behaviours of tested materials at wide range of temperature. In order to calibrate the RK constitutive model, series of compression tests at wide range of strain rates, including static, quasi-static and dynamic investigations at lowered, room and elevated temperatures, were carried out using two testing stands: servo-hydraulic machine and split Hopkinson bar. The results were analysed to determine influence of temperature and strain rate on visco-plastic response of tested steels, and show good correlation with experimental data.

  18. HOST GALAXY PROPERTIES OF THE SWIFT BAT ULTRA HARD X-RAY SELECTED ACTIVE GALACTIC NUCLEUS

    International Nuclear Information System (INIS)

    Koss, Michael; Mushotzky, Richard; Veilleux, Sylvain; Winter, Lisa M.; Baumgartner, Wayne; Tueller, Jack; Gehrels, Neil; Valencic, Lynne

    2011-01-01

    We have assembled the largest sample of ultra hard X-ray selected (14-195 keV) active galactic nucleus (AGN) with host galaxy optical data to date, with 185 nearby (z * >10.5) have a 5-10 times higher rate of spiral morphologies than in SDSS AGNs or inactive galaxies. We also see enhanced far-infrared emission in BAT AGN suggestive of higher levels of star formation compared to the comparison samples. BAT AGNs are preferentially found in the most massive host galaxies with high concentration indexes indicative of large bulge-to-disk ratios and large supermassive black holes. The narrow-line (NL) BAT AGNs have similar intrinsic luminosities as the SDSS NL Seyferts based on measurements of [O III] λ5007. There is also a correlation between the stellar mass and X-ray emission. The BAT AGNs in mergers have bluer colors and greater ultra hard X-ray emission compared to the BAT sample as a whole. In agreement with the unified model of AGNs, and the relatively unbiased nature of the BAT sources, the host galaxy colors and morphologies are independent of measures of obscuration such as X-ray column density or Seyfert type. The high fraction of massive spiral galaxies and galaxy mergers in BAT AGNs suggest that host galaxy morphology is related to the activation and fueling of local AGN.

  19. Mechanical properties of regular hexahedral lattice structure formed by selective laser melting

    International Nuclear Information System (INIS)

    Sun, Jianfeng; Yang, Yongqiang; Wang, Di

    2013-01-01

    The Ti–6Al–4V lattice structure is widely used in the aerospace field. This research first designs a regular hexahedral unit, processes the lattice structure composed of the Ti–6Al–4V units by selective laser melting technology, obtains the experimental fracture load and the compression deformation of them through compression tests, then conducts a simulation of the unit and the lattice structure through ANSYS to analyze the failure point. Later, according to the force condition of the point, the model of maximum load is built, through which the analytical formula of the fracture load of the unit and the lattice structure are obtained. The results of groups of experiments demonstrate that there exists an exponential relationship between the practical fracture load and the porosity of the lattice structure. There also exists a trigonometric function relationship between the compression deformation and the porosity of the lattice structure. The fracture analysis indicates that fracture of the units and lattice structure is brittle fracture due to cleavage fracture. (paper)

  20. Improving the antioxidant properties of quinoa flour through fermentation with selected autochthonous lactic acid bacteria.

    Science.gov (United States)

    Rizzello, Carlo Giuseppe; Lorusso, Anna; Russo, Vito; Pinto, Daniela; Marzani, Barbara; Gobbetti, Marco

    2017-01-16

    Lactic acid bacteria strains, previously isolated from the same matrix, were used to ferment quinoa flour aiming at exploiting the antioxidant potential. As in vitro determined on DPPH and ABTS radicals, the scavenging activity of water/salt-soluble extracts (WSE) from fermented doughs was significantly (Pquinoa dough fermented with Lactobacillus plantarum T0A10. The corresponding WSE was subjected to Reverse Phase Fast Protein Liquid Chromatography, and 32 fractions were collected and subjected to in vitro assays. The most active fraction was resistant to further hydrolysis by digestive enzymes. Five peptides, having sizes from 5 to 9 amino acid residues, were identified by nano-Liquid Chromatography-Electrospray Ionisation-Mass Spectra/Mass Spectra. The sequences shared compositional features which are typical of antioxidant peptides. As shown by determining cell viability and radical scavenging activity (MTT and DCFH-DA assays, respectively), the purified fraction showed antioxidant activity on human keratinocytes NCTC 2544 artificially subjected to oxidative stress. This study demonstrated the capacity of autochthonous lactic acid bacteria to release peptides with antioxidant activity through proteolysis of native quinoa proteins. Fermentation of the quinoa flour with a selected starter might be considered suitable for novel applications as functional food ingredient, dietary supplement or pharmaceutical preparations. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Probing Properties of Glassy Water and Other Liquids with Site Selective Spectroscopies

    Energy Technology Data Exchange (ETDEWEB)

    Dang, Nhan Chuong [Iowa State Univ., Ames, IA (United States)

    2005-01-01

    The standard non-photochemical hole burning (NPHB) mechanism, which involves phonon-assisted tunneling in the electronically excited state, was originally proposed to explain the light-induced frequency change of chemically stable molecules in glassy solids at liquid helium temperatures by this research group more than two decades ago. The NPHB mechanism was then further elucidated and the concept of intrinsic to glass configurational relaxation processes as pre-mediating step to the hole burning process was introduced. The latter provided the theoretical basis for NPHB to evolve into a powerful tool probing the dynamics and nature of amorphous media, which aside from ''simple'' inorganic glasses may include also ''complex'' biological systems such as living cells and cancerous/normal tissues. Presented in this dissertation are the experimental and theoretical results of hole burning properties of aluminum phthalocyanine tetrasulphonate (APT) in several different matrices: (1) hyperquenched glassy water (HGW); (2) cubic ice (Ic); and (3) water confined into poly(2-hydroxyethylmethacrylate) (poly-HEMA). In addition, results of photochemical hole burning (PHB) studies obtained for phthalocyanine tetrasulphonate (PcT) in HGW and free base phthalocyanine (Pc) in ortho-dichlorobenzene (DCB) glass are reported. The goal of this dissertation was to provide further evidence supporting the NPHB mechanism and to provide more insight that leads to a better understanding of the kinetic events (dynamics) in glasses, and various dynamical processes of different fluorescent chromorphores in various amorphous solids and the liquid that exist above the glass transition temperature (Tg). The following issues are addressed in detail: (1) time evolution of hole being burned under different conditions and in different hole burning systems; (2) temperature dependent hole profile; and (3) the structure

  2. Mesoporous TiO2 Micro-Nanometer Composite Structure: Synthesis, Optoelectric Properties, and Photocatalytic Selectivity

    Directory of Open Access Journals (Sweden)

    Kun Liu

    2012-01-01

    Full Text Available Mesoporous anatase TiO2 micro-nanometer composite structure was synthesized by solvothermal method at 180°C, followed by calcination at 400°C for 2 h. The as-prepared TiO2 was characterized by X-ray diffraction (XRD, scanning electron microscope (SEM, transmission electron microscope (TEM, and Fourier transform infrared spectrum (FT-IR. The specific surface area and pore size distribution were obtained from N2 adsorption-desorption isotherm, and the optoelectric property of the mesoporous TiO2 was studied by UV-Vis absorption spectrum and surface photovoltage spectra (SPS. The photocatalytic activity was evaluated by photodegradation of sole rhodamine B (RhB and sole phenol aqueous solutions under simulated sunlight irradiation and compared with that of Degussa P-25 (P25 under the same conditions. The photodegradation preference of this mesoporous TiO2 was also investigated for an RhB-phenol mixed solution. The results show that the TiO2 composite structure consists of microspheres (∼0.5–2 μm in diameter and irregular aggregates (several hundred nanometers with rough surfaces and the average primary particle size is 10.2 nm. The photodegradation activities of this mesoporous TiO2 on both RhB and phenol solutions are higher than those of P25. Moreover, this as-prepared TiO2 exhibits photodegradation preference on RhB in the RhB-phenol mixture solution.

  3. Copenhagen Psychosocial Questionnaire (COPSOQ – Psychometric properties of selected scales in the Polish version

    Directory of Open Access Journals (Sweden)

    Maria Widerszal-Bazyl

    2017-06-01

    Full Text Available Background: The Copenhagen Psychosocial Questionniare (COPSOQ has many advantages as compared to other similar instruments, i.a., it is not related to one single theoretical model and it measures a wide spectrum of psychosocial working conditions that have shown proven impact on health. The aim of the article is to summarize information on psychometric properties of 11 scales in the Polish version: Quantitative Demands, Emotional Demands, Influence at Work, Social Support, Possibilities for Development, Meaning of Work, Role Clarity, Quality of Leadership, Job Insecurity, Job Satisfaction, and General Health. Material and Methods: Analyses were based on the results of 4 research projects, in which the Polish version of the COPCOQ scales has been used: on a representative sample of Polish nurses (N = 4354, job insecurity in 2 groups of civil servants (N = 295, N = 724, mobbing among teachers (N = 1037 and psychological consequences of restructuring (N = 1396. The following psychometric characteristics were analysed: internal reliability, theoretical validity, and factorial validity. Results: Internal reliability of the following 8 scales was found satisfactory: Quantitative Demands, Influence at Work, Social Support, Possibilities for Development, Meaning of Work, Quality of Leadership, Job Satisfaction, and General Health (Cronbach’s α = 0.7–0.91, depending on the scale. The results of exploratory factor analyses indicated factorial separateness of the above mentioned scales. Theoretical validity of 11 scales was confirmed; they were associated with variables that can be regarded as their validity criteria. Conclusions: The 8 COPSOQ scales, in the Polish version, can be recommended for using in the research involving psychosocial job characteristics. Mean scores on these scales and standard deviations given in the article can serve as reference points during an evaluation of received results. Med Pr 2017;68(3:329–348

  4. Aldehyde dehydrogenase (ALDH activity does not select for cells with enhanced aggressive properties in malignant melanoma.

    Directory of Open Access Journals (Sweden)

    Lina Prasmickaite

    Full Text Available BACKGROUND: Malignant melanoma is an exceptionally aggressive, drug-resistant and heterogeneous cancer. Recently it has been shown that melanoma cells with high clonogenic and tumourigenic abilities are common, but markers distinguishing such cells from cells lacking these abilities have not been identified. There is therefore no definite evidence that an exclusive cell subpopulation, i.e. cancer stem cells (CSC, exists in malignant melanoma. Rather, it is suggested that multiple cell populations are implicated in initiation and progression of the disease, making it of importance to identify subpopulations with elevated aggressive properties. METHODS AND FINDINGS: In several other cancer forms, Aldehyde Dehydrogenase (ALDH, which plays a role in stem cell biology and resistance, is a valuable functional marker for identification of cells that show enhanced aggressiveness and drug-resistance. Furthermore, the presence of ALDH(+ cells is linked to poor clinical prognosis in these cancers. By analyzing cell cultures, xenografts and patient biopsies, we showed that aggressive melanoma harboured a large, distinguishable ALDH(+ subpopulation. In vivo, ALDH(+ cells gave rise to ALDH(- cells, while the opposite conversion was rare, indicating a higher abilities of ALDH(+ cells to reestablish tumour heterogeneity with respect to the ALDH phenotype. However, both ALDH(+ and ALDH(- cells demonstrated similarly high abilities for clone formation in vitro and tumour initiation in vivo. Furthermore, both subpopulations showed similar sensitivity to the anti-melanoma drugs, dacarbazine and lexatumumab. CONCLUSIONS: These findings suggest that ALDH does not distinguish tumour-initiating and/or therapy-resistant cells, implying that the ALDH phenotype is not associated with more-aggressive subpopulations in malignant melanoma, and arguing against ALDH as a "universal" marker. Besides, it was shown that the ability to reestablish tumour heterogeneity is not

  5. Mechanical property characterization and impact resistance of selected graphite/PEEK composite materials

    Science.gov (United States)

    Baker, Donald J.

    1994-01-01

    To use graphite polyetheretherketone (PEEK) material on highly curved surfaces requires that the material be drapable and easily conformable to the surface. This paper presents the mechanical property characterization and impact resistance results for laminates made from two types of graphite/PEEK materials that will conform to a curved surface. These laminates were made from two different material forms. These forms are: (1) a fabric where each yarn is a co-mingled Celion G30-500 3K graphite fiber and PEEK thermoplastic fiber; and (2) an interleaved material of Celion G30-500 3K graphite fabric interleaved with PEEK thermoplastic film. The experimental results from the fabric laminates are compared with results for laminates made from AS4/PEEK unidirectional tape. The results indicate that the tension and compression moduli for quasi-isotropic and orthotropic laminates made from fabric materials are at least 79 percent of the modulus of equivalent laminates made from tape material. The strength of fabric material laminates is at least 80 percent of laminates made from tape material. The evaluation of fabric material for shear stiffness indicates that a tape material laminate could be replaced by a fabric material laminate and still maintain 89 percent of the shear stiffness of the tape material laminate. The notched quasi-isotropic compression panel failure strength is 42 to 46 percent of the unnotched quasi-isotropic laminate strength. Damage area after impact with 20 ft-lbs of impact energy is larger for the co-mingled panels than for the interleaved panels. The inerleaved panels have less damage than panels made from tape material. Residual compression strength of quasi-isotropic panels after impact of 20 ft-lbs of energy varies between 33 percent of the undamaged quasi-isotropic material strength for the tape material and 38 percent of the undamaged quasi-isotropic material strength for the co-mingled fabric material.

  6. Characterization of a subset of oligodendrocytes separated on the basis of selective adherence properties.

    Science.gov (United States)

    Szuchet, S; Yim, S H

    1984-01-01

    A subset of oligodendrocytes (B3,f) was isolated by taking advantage of selective cell-substratum interaction. B3,f cells were characterized morphologically, biochemically, and immunocytochemically. Oligodendrocytes were isolated from 4-to-6-month-old lamb brains by a modified version of our published procedure [Szuchet et al, J Neurosci Methods 3:7-19, 1980]. Freshly isolated cells from band III were plated on plastic culture plates at a concentration of 2 X 10(6) cells/ml. Approximately 40% of the cells attached to the plate under these conditions. The remaining cells formed small floating clusters. We refer to the latter as B3,f oligodendrocytes. After 4 to 5 days, the supernatant containing B3,f cells was removed and centrifuged, and the pellet was resuspended in culture medium and replated on polylysine-coated petri dishes. B3,f oligodendrocytes attached to this surface and extended an intricate network of processes. The purity of the cultures, judged by the number of cells staining with a monoclonal antibody against galactocerebroside was 98-99%. This high degree of cell homogeneity was maintained throughout the life of the cultures. B3,f cells appeared to be highly differentiated and remained so in vitro. This is surmised by the expression of oligodendrocytic characteristic functions such as high levels of CNPase activity typically, 5 microM/min/mgP; high incorporation of H2 35SO4 into sulfatides, an overall lipid metabolism that mimics events associated with myelinogenesis [Szuchet et al, PNAS 80:7019-7023, 1983]; the presence, detected immunocytochemically, of myelin-associated glycoprotein and myelin basic proteins. It is concluded that this culture system offers an opportunity for studying the biology of interfascicular oligodendrocytes and their interaction with neurons and/or astrocytes. It also should open up a way of examining the relevance of oligodendrocyte polymorphism.

  7. Drug-selected human lung cancer stem cells: cytokine network, tumorigenic and metastatic properties.

    Directory of Open Access Journals (Sweden)

    Vera Levina

    2008-08-01

    Full Text Available Cancer stem cells (CSCs are thought to be responsible for tumor regeneration after chemotherapy, although direct confirmation of this remains forthcoming. We therefore investigated whether drug treatment could enrich and maintain CSCs and whether the high tumorogenic and metastatic abilities of CSCs were based on their marked ability to produce growth and angiogenic factors and express their cognate receptors to stimulate tumor cell proliferation and stroma formation.Treatment of lung tumor cells with doxorubicin, cisplatin, or etoposide resulted in the selection of drug surviving cells (DSCs. These cells expressed CD133, CD117, SSEA-3, TRA1-81, Oct-4, and nuclear beta-catenin and lost expression of the differentiation markers cytokeratins 8/18 (CK 8/18. DSCs were able to grow as tumor spheres, maintain self-renewal capacity, and differentiate. Differentiated progenitors lost expression of CD133, gained CK 8/18 and acquired drug sensitivity. In the presence of drugs, differentiation of DSCs was abrogated allowing propagation of cells with CSC-like characteristics. Lung DSCs demonstrated high tumorogenic and metastatic potential following inoculation into SCID mice, which supported their classification as CSCs. Luminex analysis of human and murine cytokines in sonicated lysates of parental- and CSC-derived tumors revealed that CSC-derived tumors contained two- to three-fold higher levels of human angiogenic and growth factors (VEGF, bFGF, IL-6, IL-8, HGF, PDGF-BB, G-CSF, and SCGF-beta. CSCs also showed elevated levels of expression of human VEGFR2, FGFR2, CXCR1, 2 and 4 receptors. Moreover, human CSCs growing in SCID mice stimulated murine stroma to produce elevated levels of angiogenic and growth factors.These findings suggest that chemotherapy can lead to propagation of CSCs and prevention of their differentiation. The high tumorigenic and metastatic potentials of CSCs are associated with efficient cytokine network production that may represent

  8. Photocatalytic properties and selective antimicrobial activity of TiO{sub 2}(Eu)/CuO nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Michal, Robert [Department of Inorganic Chemistry, Faculty of Natural Sciences, Comenius University in Bratislava, 84215 Bratislava (Slovakia); Dworniczek, Ewa [Department of Microbiology, Wroclaw Medical University, 50368 Wroclaw (Poland); Caplovicova, Maria [STU Centre for Nanodiagnostics, Slovak University of Technology, 81243 Bratislava (Slovakia); Monfort, Olivier [Department of Inorganic Chemistry, Faculty of Natural Sciences, Comenius University in Bratislava, 84215 Bratislava (Slovakia); Lianos, Panagiotis [Department of Chemical Engineering, University of Patras, 26500 Patras (Greece); Caplovic, Lubomir [Institute of Materials Science, Faculty of Materials Science and Technology, Slovak University of Technology, 91724 Trnava (Slovakia); Plesch, Gustav, E-mail: plesch@fns.uniba.sk [Department of Inorganic Chemistry, Faculty of Natural Sciences, Comenius University in Bratislava, 84215 Bratislava (Slovakia)

    2016-05-15

    Highlights: • Nanocomposites composed of Eu-doped anatase grafted with CuO. • Increase in photocatalytic hydrogen production due to CuO acting as electrons sink. • CuO in composites decreasing the photoinduced total mineralization of phenol. • Selective photoinduced antimicrobial activity against Enterococcus species. - Abstract: TiO{sub 2}(Eu)/CuO nanocomposites were prepared by precipitation method. The anatase nanocrystallites with a size of 26 nm exhibited well crystallized and characteristical dipyramidal morphology and {1 0 1} and {0 0 1} faceting. Transmission electron microscopy photographs with atomic resolution showed that the Eu(III) dopants were bounded on surface of titania. In the composites, the CuO nanocrystals exhibiting a monoclinic tenorite structure with a size in the range from 2 to 5 nm were grafted to the surface of titania. The influence of copper(II) oxide led to distinct selectivity in the photocatalytic and antimicrobial properties of the investigated TiO{sub 2}(Eu)/CuO nanocomposites. While the presence of CuO nanocrystals strongly increased the photocatalytic production of hydrogen by ethanol reforming, it decreased the activity in photoinduced total mineralization of phenol comparing with non-modified TiO{sub 2}(Eu). In investigated TiO{sub 2}(Eu)/CuO powders, the photoinduced antimicrobial activity against membranes of Enterococcus species was influenced by the selective binding of CuO to the surface of the microorganism leading to distinct selectivity in their action. The activity against Enterococcus faecalis was higher than against Enterococcus faecium.

  9. A New Variable Selection Method Based on Mutual Information Maximization by Replacing Collinear Variables for Nonlinear Quantitative Structure-Property Relationship Models

    Energy Technology Data Exchange (ETDEWEB)

    Ghasemi, Jahan B.; Zolfonoun, Ehsan [Toosi University of Technology, Tehran (Korea, Republic of)

    2012-05-15

    Selection of the most informative molecular descriptors from the original data set is a key step for development of quantitative structure activity/property relationship models. Recently, mutual information (MI) has gained increasing attention in feature selection problems. This paper presents an effective mutual information-based feature selection approach, named mutual information maximization by replacing collinear variables (MIMRCV), for nonlinear quantitative structure-property relationship models. The proposed variable selection method was applied to three different QSPR datasets, soil degradation half-life of 47 organophosphorus pesticides, GC-MS retention times of 85 volatile organic compounds, and water-to-micellar cetyltrimethylammonium bromide partition coefficients of 62 organic compounds.The obtained results revealed that using MIMRCV as feature selection method improves the predictive quality of the developed models compared to conventional MI based variable selection algorithms.

  10. A New Variable Selection Method Based on Mutual Information Maximization by Replacing Collinear Variables for Nonlinear Quantitative Structure-Property Relationship Models

    International Nuclear Information System (INIS)

    Ghasemi, Jahan B.; Zolfonoun, Ehsan

    2012-01-01

    Selection of the most informative molecular descriptors from the original data set is a key step for development of quantitative structure activity/property relationship models. Recently, mutual information (MI) has gained increasing attention in feature selection problems. This paper presents an effective mutual information-based feature selection approach, named mutual information maximization by replacing collinear variables (MIMRCV), for nonlinear quantitative structure-property relationship models. The proposed variable selection method was applied to three different QSPR datasets, soil degradation half-life of 47 organophosphorus pesticides, GC-MS retention times of 85 volatile organic compounds, and water-to-micellar cetyltrimethylammonium bromide partition coefficients of 62 organic compounds.The obtained results revealed that using MIMRCV as feature selection method improves the predictive quality of the developed models compared to conventional MI based variable selection algorithms

  11. Effect of organic farming on selected raw cow milk components and properties

    Directory of Open Access Journals (Sweden)

    Ivana Cermanová

    2011-01-01

    Full Text Available Organic dairying is an alternative for friendly exploitation of environment. This paper was focused on impacts of organic dairying on milk composition and properties. The conventional (C cow milk was compared to organic (O milk. Holstein bulk milk samples (BMSs from winter and summer season in 4 C and 4 O (n = 32 and 32 BMSs; 2 years herds were investigated. 6 herds were grazed and 2 C herds were not grazed. Mean O cow milk yield (MY, 305 lactation days was 7037.3 ± 421.5 and C MY 7015.8 ± 1068.1 kg. Higher values (P < 0.05 in O milk had: log acetone (0.7321 > 0.6048; titration acidity (8.34 > 7.82 ml 0.25 mol.l−1 NaOH; alcohol stability (0.6 > 0.44 ml; time for enzymatic coagulation (150.75 > 115.03 second; whey protein (0.54 > 0.49%; fat/crude protein (1.2 > 1.15; milk fermentation ability (FAM by titration (31.45 > 22.18 ml 0.25 mol.l−1 NaOH. Lower values (P < 0.05 in O milk had: solids–not–fat (8.64 < 8.73%; urea content (19.91 < 29.03 mg.100ml−1; electrical conductivity (3.66 < 4.08 mS.cm−1; whey volume (32.03 < 34.53 ml; crude protein (3.16 < 3.25%; casein (2.47 < 2.58%; non–protein nitrogen compounds (0.15 < 0.18%; urea nitrogen in non-protein nitrogen ratio (40.81 < 49.0%; casein numbers for crude protein and true protein (78.12 < 79.58 and 81.99 < 84.11%; coli bacteria count in normal and logarithm form (330.56 < 1502.92 CFU.ml−1 and 1.484 < 2.5823; actual yoghurt acidity (4.71 < 4.8. O cows suffered probably from lower energy and nitrogen compounds intake due to feeding under mentioned conditions. O milk could be a little better environment for yoghurt cultivation.

  12. Comparisonof physicochemical properties of selected locally available legume varieties (mung bean, cowpea and soybean

    Directory of Open Access Journals (Sweden)

    Kulasooriyage Tharuka Gunathilake

    2016-10-01

    Full Text Available Grain legumes are widely used as high-protein contained crops that play a secondary role to cereal or root crops. In Sri Lanka various legume species are cultivated and often utilised in the whole grain boiled form. The objective of present study was to analyse and compare locally grown legumes varieties; Mung bean (MI 5, MI 6, Cowpea (Bombay, Waruni, Dhawal, MICP1, ANKCP1 and soybean (pb1, MISB1 for their morphological characteristics, proximate and mineral composition (Fe, Ca, Zn, K, P. Seed shape, seed coat texture and colour, seed size and 100 seed weight (g were observed morphological characteristics in present study. Most of the characteristics of mung bean and soybean were similar within their species whereas characteristics of cowpea varieties largely differed. Values of 100 seed weight among the varieties of mung bean, soybean and cowpea were ranged from 5.8 - 6.5 g, 13.5 - 14.1 g and 13.4 - 17.2 g, respectively. The moisture content of all legume seeds ranged from 6.81% to 11.99%. Results were shown that the protein content significantly higher in soybean (36.56 - 39.70% followed by mung bean (26.56 - 25.99% and cowpea (25.22 - 22.84% respectively. Range of total carbohydrate, crude fat, crude fibre and total ash contents of nine legume varieties varied from 15.29 - 62.97%, 1.25 - 22.02%, 3.04 - 7.93% and 3.43 - 6.35 respectively. potassium (K, phosphorus (P, calcium (Ca, iron (Fe and zinc (Zn ranged from 1000 - 1900, 360 - 669, 15.0 - 192.3, 2.26 - 11.6 and 1.67 - 4.26 mg.100g-1 respectively in all the species of studied legume varieties. The wide variation in the chemical and physical properties of observed nine legume varieties, suggesting possible applications for various end-use products. 

  13. Scintillation properties of selected oxide monocrystals activated with Ce and Pr

    Science.gov (United States)

    Wojtowicz, Andrzej J.; Drozdowski, Winicjusz; Wisniewski, Dariusz; Lefaucheur, Jean-Luc; Galazka, Zbigniew; Gou, Zhenhui; Lukasiewicz, Tadeusz; Kisielewski, Jaroslaw

    2006-01-01

    In the last 10-15 years there has been a significant effort toward development of new, more efficient and faster materials for detection of ionizing radiation. A growing demand for better scintillator crystals for detection of 511 keV gamma particles has been due mostly to recent advances in modern imaging systems employing positron emitting radionuclides for medical diagnostics in neurology, oncology and cardiology. While older imaging systems were almost exclusively based on BGO and NaI:Tl crystals the new systems, e.g., ECAT Accel, developed by Siemens/CTI, are based on recently discovered and developed LSO (Lu 2SiO 5:Ce, Ce-activated lutetium oxyorthosilicate) crystals. Interestingly, despite very good properties of LSO, there still is a strong drive toward development of new scintillator crystals that would show even better performance and characteristics. In this presentation we shall review spectroscopic and scintillator characterization of new complex oxide crystals, namely LSO, LYSO, YAG, LuAP (LuAlO 3, lutetium aluminate perovskite) and LuYAP activated with Ce and Pr. The LSO:Ce crystals have been grown by CTI Inc (USA), LYSO:Ce, LuAP:Ce and LuYAP:Ce crystals have been grown by Photonic Materials Ltd., Scotland (PML is the only company providing large LuAP:Ce crystals on a commercial scale), while YAG:Pr and LuAP:Pr crystals have been grown by Institute of Electronic Materials Technology (Poland). All these crystals have been characterized at Institute of Physics, N. Copernicus University (Poland). We will review and compare results of measurements of radioluminescence, VUV spectroscopy, scintillation light yields, scintillation time profiles and low temperature thermoluminescence performed on these crystals. We will demonstrate that all experiments clearly indicate that there is a significant room for improvement of LuAP, LuYAP and YAG. While both Ce-activated LSO and LYSO perform very well, we also note that LuYAP:Ce, LuAP:Ce and YAG:Pr offer some

  14. Cs-selective mineral adsorbents in columns: physico-chemical properties and modeling

    International Nuclear Information System (INIS)

    Michel, Caroline

    2015-01-01

    Following the nuclear disaster in Fukushima Dai-Ichi, thousands of tons of fresh water and seawater were used for cooling the reactors or contaminated as a result of groundwater seepage. Decontamination of these waters is complicated by the presence of other cations (Na + , K + , Ca 2+ , Mg 2+ ) naturally present in these waters. Decontamination process in columns packed was studied in this context with two types of mineral adsorbents: the TERMOXID 35 and the SORBMATECH 202. The first one is a commercial adsorbent and consists of mixed ferrocyanide K/Ni impregnated over a solid matrix Zr(OH) 4 . The second one was synthesized in CEA and is composed of ferrocyanide K/Cu impregnated over a solid matrix SiO 2 . Both materials have shown a high efficiency for Cs decontamination in seawater with K(d,Cs) of about 10 5 mL/g. Batch studies conducted in different solutions (pure water, fresh water and seawater) allowed determining sorption kinetics and ion exchange mechanisms responsible for the sorption of Cs + , taking into account competitive effects of the natural water cations (Na + , K + , Ca 2+ , Mg 2+ ). Modelling of batches was performed with the geochemical code CHESS considering competitive effects according to the Vanselow formalism and selectivity coefficients, developing a specific thermodynamic database. The performances of these materials were then tested in column. The operating parameters such as Darcy's velocity and the H/D ratio were studied for a proper functioning of this process. The T35 has proven to be less efficient mainly because of the slow diffusion of Cs in the pores of the material. The S 2 O 2 has proven to be a good candidate for the application of high flow rates. The breakthrough curves obtained in fresh water have been modelled with the reactive transport codes HYTEC and OPTIPUR using the CHESS thermodynamic database. This approach will eventually help to support the design of a decontamination unit by the operator. (author) [fr

  15. Design and Synthesis of Novel and Selective Glycine Transporter-1 (GlyT1) Inhibitors with Memory Enhancing Properties.

    Science.gov (United States)

    Santora, Vincent J; Almos, Theresa A; Barido, Richard; Basinger, Jillian; Bellows, Chris L; Bookser, Brett Carder; Breitenbucher, J Guy; Broadbent, Nicola J; Cabebe, Clifford; Chai, Chih-Kun; Chen, Mi; Chow, Stephine; Chung, De Michael; Crickard, Lindsay; Danks, Anne M; Freestone, Graeme; Gitnick, Dany; Gupta, Varsha; Hoffmaster, Christine; Hudson, Andrew R; Kaplan, Alan P; Kennedy, Michael R; Lee, Dong; Limberis, James; Ly, Kiev; Mak, Chi Ching; Masatsugu, Brittany; Morse, Andrew C; Na, Jim; Neul, David; Nikpur, John; Peters, Marco; Petroski, Robert E; Renick, Joel; Sebring, Kristen; Sevidal, Samantha; Tabatabaei, Ali; Wen, Jenny; Yan, Yingzhuo; Yoder, Zachary W; Zook, Douglas

    2018-06-11

    We report here the identification and optimization of a novel series of potent GlyT1 inhibitors. A ligand design campaign that utilized known GlyT1 inhibitors as starting points led to the identification of a novel series of pyrrolo[3,4-c]pyrazoles amides (21-50) with good in vitro potency. Subsequent optimization of physicochemical and in vitro ADME properties produced several compounds with promising pharmacokinetic profiles. In vivo inhibition of GlyT1 was demonstrated for select compounds within this series by measuring the elevation of glycine in the cerebrospinal fluid (CSF) of rats after a single oral dosing of 10 mg/kg. Ultimately, an optimized lead, compound 46, demonstrated in vivo efficacy in a rat Novel Object Recognition (NOR) assay after oral dosing at 0.1, 1, and 3 mg/kg.

  16. THE INFLUENCE OF THE INSTALLATION METHOD ON THE SELECTED PROPERTIES OF BIODEGRADABLE GEOTEXTILES USED IN ENVIRONMENTAL ENGINEERING

    Directory of Open Access Journals (Sweden)

    Joanna Beata Grzybowska-Pietras

    2017-06-01

    Full Text Available In the engineering constructions there are used biodegradable geotextiles, that are performing primarily a function of surface anti-erosion protection. Their biodegradability supports the development of vegetation, and protects the surface of the slope from the moment of installation in the ground. In order to achieve this functionality there are used mainly biononwovens and woven fabrics made of natiral fibers. In the paper there are presented results of studies on the effect of the instalation of the biononwoven (Maliwatt type with grass seeds applied in real conditions at a specified time (from November to June, on the selected physical, mechanical and hydraulic properties , and the development of vegetation (grasses. The experiment adopted two versions of instalation of nonwovens. In the first case geotextile was mounted directly on the ground, in the second additionally have been covered with a layer of native soil.

  17. Selective Clay Placement within a Silicate Clay-Epoxy Blend Nanocomposite and the Effect on Physical Properties

    Science.gov (United States)

    Miller, Sandi G.; Scheiman, Daniel A; Kohlmman, Lee W.

    2009-01-01

    Many epoxy systems under consideration for composite pressure vessels are composed of toughened epoxy resins. In this work, epoxy blends containing both rigid aromatic and flexible aliphatic components were prepared, to model toughened systems, and determine the optimum route of silicate addition. Compositions were chosen such that both glassy and rubbery resins were obtained at room temperature. The physical properties of the nanocomposites varied with T(g) and silicate placement, however, nanocomposite T(g)s were observed which exceeded that of the base resin by greater than 10 C. The tensile strength of the glassy resin remained constant or decreased on the dispersion of clay while that of the rubbery material doubled. Selectively placing the clay in the aliphatic component of the rubbery blend resulted in a greater than 100% increase in material toughness.

  18. Comprehensive study of rheological and surface properties of the selected slag system in the context of its internal structure

    Directory of Open Access Journals (Sweden)

    L. Řeháčková

    2016-10-01

    Full Text Available Rheological (dynamic viscosity, flow curves and surface properties (surface tension of real slag system were experimentally investigated. Measurements of dynamic viscosity were performed with use of the high-temperature viscometer Anton Paar FRS 1 600. The method of sessile drop was used for measurement of surface tension. Surface tension and dynamic viscosity were measured in the temperature interval from 1 200 to 1 600 °C. The structural characteristics of the selected samples were determined by X-ray diffraction (XRD. The samples for given analysis were prepared by quench cooling. Experimentally determined values of dynamic viscosity and surface tension were compared with the results of X-ray diffraction phase analysis.

  19. The Effect of Emulsion Intensity on Selected Sensory and Instrumental Texture Properties of Full-Fat Mayonnaise

    Science.gov (United States)

    Olsson, Viktoria; Håkansson, Andreas

    2018-01-01

    Varying processing conditions can strongly affect the microstructure of mayonnaise, opening up new applications for the creation of products tailored to meet different consumer preferences. The aim of the study was to evaluate the effect of emulsification intensity on sensory and instrumental characteristics of full-fat mayonnaise. Mayonnaise, based on a standard recipe, was processed at low and high emulsification intensities, with selected sensory and instrumental properties then evaluated using an analytical panel and a back extrusion method. The evaluation also included a commercial reference mayonnaise. The overall effects of a higher emulsification intensity on the sensory and instrumental characteristics of full-fat mayonnaise were limited. However, texture was affected, with a more intense emulsification resulting in a firmer mayonnaise according to both back extrusion data and the analytical sensory panel. Appearance, taste and flavor attributes were not affected by processing. PMID:29342128

  20. Effects of microstructure on the elastic properties of selected Ta2O5--Eu2O3 compositions

    International Nuclear Information System (INIS)

    Malarkey, C.J.

    1977-06-01

    Elastic properties and internal friction of selected compositions of tantala-doped monoclinic europia were studied at temperatures up to 1500 0 C using the sonic resonance technique. Unit cell parameters between 25C and 1000 0 C for monoclinic Eu 2 O 3 were calculated from high temperature x-ray diffractometer data. Large-grained monoclinic specimens having less than 6.0 Ta cation percent substitution exhibited anomalous elastic behavior when thermally cycled. Compositions above this addition level exhibited linear elastic behavior. Internal friction values also varied abnormally with grain size, composition, and temperature. The anomalous behavior was attributed to microcracking caused by thermal expansion anisotropies. The critical grain size was found to be approximately 14 μm. The high temperature diffractometry measurements supported the postulate that the grain coarsening effect associated with sintered monoclinic Eu 2 O 3 is the controlling factor for microcracking

  1. The Influence of Selective Laser Melting Parameters on Density and Mechanical Properties of AlSi10Mg

    Directory of Open Access Journals (Sweden)

    Raus A. A.

    2016-01-01

    Full Text Available Selective Laser Melting (SLM is one of the most effective powder bed technique in the additive Manufacturing (AM which able to fabricate functional metal parts directly from 3D Computer Aided Design (CAD file data. In this paper, the influence of SLM parameters, such as laser power, scanning speed and hatching distance on the density of AlSi10Mg samples are investigated using one factor at a time (OFAT. Furthermore, the optimum results are used to fabricate samples for hardness, tensile strength, and impact toughness test. It is revealed that AlSi10Mg parts fabricated by SLM achieving the best density of 99.13% at the value of 350 watts laser power, 1650 mm/s scanning speed and hatching distance 0.13mm, whereby resulted comparable and even better mechanical properties to those of conventionally HDPC A360F and HDPC A360T6 alloys although without any comprehensive post processing methods.

  2. THE HOST GALAXY PROPERTIES OF VARIABILITY SELECTED AGN IN THE PAN-STARRS1 MEDIUM DEEP SURVEY

    Energy Technology Data Exchange (ETDEWEB)

    Heinis, S.; Gezari, S.; Kumar, S. [Department of Astronomy, University of Maryland, College Park, MD (United States); Burgett, W. S.; Flewelling, H.; Huber, M. E.; Kaiser, N.; Wainscoat, R. J.; Waters, C. [Institute for Astronomy, University of Hawaii at Manoa, Honolulu, HI 96822 (United States)

    2016-07-20

    We study the properties of 975 active galactic nuclei (AGNs) selected by variability in the Pan-STARRS1 Medium deep Survey. Using complementary multi-wavelength data from the ultraviolet to the far-infrared, we use spectral energy distribution fitting to determine the AGN and host properties at z < 1 and compare to a well-matched control sample. We confirm the trend previously observed: that the variability amplitude decreases with AGN luminosity, but we also observe that the slope of this relation steepens with wavelength, resulting in a “redder when brighter” trend at low luminosities. Our results show that AGNs are hosted by more massive hosts than control sample galaxies, while the rest frame dust-corrected NUV r color distribution of AGN hosts is similar to control galaxies. We find a positive correlation between the AGN luminosity and star formation rate (SFR), independent of redshift. AGN hosts populate the entire range of SFRs within and outside of the Main Sequence of star-forming galaxies. Comparing the distribution of AGN hosts and control galaxies, we show that AGN hosts are less likely to be hosted by quiescent galaxies and more likely to be hosted by Main Sequence or starburst galaxies.

  3. Chemical Profiling and Evaluation of Antioxidant and Anti-Microbial Properties of Selected Commercial Essential Oils: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Ângelo Luís

    2017-06-01

    Full Text Available Background: The last decades have seen an increased awareness by the scientific community of the extent of resistance to conventional antibiotics, particularly with respect to the emerging multidrug-resistant pathogenic microbes. Additionally, natural antioxidants have received significant attention among food professionals and consumers because of their assumed safety and potential therapeutic value. The aim of this work was to assess the antioxidant activities of eight selected commercial essential oils (EOs, together with the evaluation of their antibacterial and anti-quorum sensing properties. Methods: The chemical profiling of the EOs was performed using gas chromatography-mass spectrometry (GC-MS analysis. The antioxidant properties of the EOs were evaluated using the 2,2-diphenyl-1-picrylhydrazyl (DPPH free radical scavenging assay and by β-carotene bleaching test. Disc diffusion assays were employed to evaluate the anti-bacterial and anti-quorum sensing activities of the EOs. Results: It was observed that EOs from three Eucalyptus species are rich in eucalyptol. Generally, linalool is abundant in EOs from four Lavandula species. The oil of Cymbopogon citratus is the one with the best capacity to scavenge the DPPH free radicals and presented great antibacterial activity. Conclusions: The geographical origins of the plant species are determinant factors in the EO composition and in the corresponding biological activities.

  4. Influence of load and reinforcement content on selected tribological properties of Al/SiC/Gr hybrid composites

    Directory of Open Access Journals (Sweden)

    Sandra Veličković

    2018-04-01

    Full Text Available Hybrid materials with the metal matrix are important engineering materials due to their outstanding mechanical and tribological properties. Here are presented selected tribological properties of the hybrid composites with the matrix made of aluminum alloy and reinforced by the silicon carbide and graphite particles. The tribological characteristics of such materials are superior to characteristics of the matrix – the aluminum alloy, as well as to characteristics of the classical metal-matrix composites with a single reinforcing material. Those characteristics depend on the volume fractions of the reinforcing components, sizes of the reinforcing particles, as well as on the fabrication process of the hybrid composites. The considered tribological characteristics are the friction coefficient and the wear rate as functions of the load levels and the volume fractions of the graphite and the SiC particles. The wear rate increases with increase of the load and the Gr particles content and with reduction of the SiC particles content. The friction coefficient increases with the load, as well as with the SiC particles content increase.

  5. Comparison of Microstructure and Mechanical Properties of Scalmalloy® Produced by Selective Laser Melting and Laser Metal Deposition.

    Science.gov (United States)

    Awd, Mustafa; Tenkamp, Jochen; Hirtler, Markus; Siddique, Shafaqat; Bambach, Markus; Walther, Frank

    2017-12-23

    The second-generation aluminum-magnesium-scandium (Al-Mg-Sc) alloy, which is often referred to as Scalmalloy ® , has been developed as a high-strength aluminum alloy for selective laser melting (SLM). The high-cooling rates of melt pools during SLM establishes the thermodynamic conditions for a fine-grained crack-free aluminum structure saturated with fine precipitates of the ceramic phase Al₃-Sc. The precipitation allows tensile and fatigue strength of Scalmalloy ® to exceed those of AlSi10Mg by ~70%. Knowledge about properties of other additive manufacturing processes with slower cooling rates is currently not available. In this study, two batches of Scalmalloy ® processed by SLM and laser metal deposition (LMD) are compared regarding microstructure-induced properties. Microstructural strengthening mechanisms behind enhanced strength and ductility are investigated by scanning electron microscopy (SEM). Fatigue damage mechanisms in low-cycle (LCF) to high-cycle fatigue (HCF) are a subject of study in a combined strategy of experimental and statistical modeling for calculation of Woehler curves in the respective regimes. Modeling efforts are supported by non-destructive defect characterization in an X-ray computed tomography (µ-CT) platform. The investigations show that Scalmalloy ® specimens produced by LMD are prone to extensive porosity, contrary to SLM specimens, which is translated to ~30% lower fatigue strength.

  6. Microstructures and mechanical properties of Co-29Cr-6Mo alloy fabricated by selective laser melting process for dental applications.

    Science.gov (United States)

    Takaichi, Atsushi; Suyalatu; Nakamoto, Takayuki; Joko, Natsuka; Nomura, Naoyuki; Tsutsumi, Yusuke; Migita, Satoshi; Doi, Hisashi; Kurosu, Shingo; Chiba, Akihiko; Wakabayashi, Noriyuki; Igarashi, Yoshimasa; Hanawa, Takao

    2013-05-01

    The selective laser melting (SLM) process was applied to a Co-29Cr-6Mo alloy, and its microstructure, mechanical properties, and metal elution were investigated to determine whether the fabrication process is suitable for dental applications. The microstructure was evaluated using scanning electron microscopy with energy-dispersed X-ray spectroscopy (SEM-EDS), X-ray diffractometry (XRD), and electron back-scattered diffraction pattern analysis. The mechanical properties were evaluated using a tensile test. Dense builds were obtained when the input energy of the laser scan was higher than 400 J mm⁻³, whereas porous builds were formed when the input energy was lower than 150 J mm⁻³. The microstructure obtained was unique with fine cellular dendrites in the elongated grains parallel to the building direction. The γ phase was dominant in the build and its preferential orientation was confirmed along the building direction, which was clearly observed for the builds fabricated at lower input energy. Although the mechanical anisotropy was confirmed in the SLM builds due to the unique microstructure, the yield strength, UTS, and elongation were higher than those of the as-cast alloy and satisfied the type 5 criteria in ISO22764. Metal elution from the SLM build was smaller than that of the as-cast alloy, and thus, the SLM process for the Co-29Cr-6Mo alloy is a promising candidate for fabricating dental devices. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Microstructure and tensile properties of selectively laser-melted and of HIPed laser-melted Ti–6Al–4V

    International Nuclear Information System (INIS)

    Qiu, Chunlei; Adkins, Nicholas J.E.; Attallah, Moataz M.

    2013-01-01

    Ti–6Al–4V samples have been prepared by selective laser melting (SLM) with varied processing conditions. Some of the samples were stress-relieved or hot isostatically pressed (HIPed). The microstructures of all samples were characterised using optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) and the tensile properties measured before and after HIPing. It was found that the porosity level generally decreased with increase of laser power and laser scanning speed. Horizontally built samples were found to have a higher level of porosity than vertically built samples. The as-fabricated microstructure was dominated by columnar grains and martensites. HIPing closed the majority of the pores and also fully transformed the martensite into α and β phases. The as-fabricated microstructure exhibits very high tensile strengths but poor ductility with elongation generally smaller than 10%. The horizontally built samples show even lower elongation than vertically built samples. HIPing considerably improved ductility but led to a reduction in strength. With HIPing, the SLMed samples were found to show tensile properties comparable with those thermomechanically processed and annealed samples

  8. Effect of Different Connection Modes on Bolt Structural Properties of TC4 Alloy in Selective Laser Melting

    Science.gov (United States)

    Li, Xiaodan; Huang, Shuangjun; Xu, Liang; Hui, Li; Zhou, Song

    2017-12-01

    The bolt structural properties of selective laser melted (SLM) samples produced from TC4 powder metal has been investigated. Two different connection molds relative to single lap joint and bilateral lap joint as well as two different state of surface quality were considered. Samples and test procedures were designed in accordance with HB 5143 and HB 5287 standard. The results show that there is a strong influence of connection molds on the dynamic behavior of SLM produced TC4. The mechanical properties of bilateral lap joint are better than those of the single lap joint. Meanwhile the fatigue performance of the bilateral lap joint is much stronger than that of the single lap joint which it is a symmetrical structure of the two-shear test on both sides of the force evenly, while the single lap joint is a single shear sample of the uneven force. There are two kinds of fracture form most of which are broken in the first row of screw and a small part in the middle of the connecting plate.

  9. Evaluation and Selection of Common Bean (Phaseolus Vulgaris L.) Genotypes for Root Traits Associated with Phosphorus (P) Acquisition Efficiency and the Use of {sup 32}P Isotope in Studies on P Uptake by Root Hairs

    Energy Technology Data Exchange (ETDEWEB)

    Miguel, M. A.; Jochua, C. [Agricultural Research Institute of Mozambique (IIAM), Maputo (Mozambique); Lynch, J. P. [Pennsylvania State University, University Park, PA (United States)

    2013-11-15

    Low phosphorus (P) availability is one of the main edaphic constraints limiting crop production and productivity in most of the tropical agro-ecosystems. Several root traits are known to be associated with P acquisition efficiency in low P soils. These root traits include root hairs. Computer modeling, laboratory and field studies show the depletion of {sup 32}P-phosphate around roots and that the depletion zone is influenced by the length and density of root hairs. We conducted a study involving a series of experiments with the objective of evaluating the variability of root traits associated with P uptake efficiency among common bean (Phaseolus vulgaris L.) genotypes, and to understand the mechanisms of long root hairs leading to the increase in P uptake in common bean. The study included (a) the screening of common bean genotypes in the laboratory and in the field for root traits, and (b) the use of radioactive phosphorus ({sup 32}P) in the experiments conducted in the greenhouse. For laboratory screening, seedlings were germinated in paper rolls in a growth media for 3 days before evaluation for basal root whorl number (BRWN), basal root number (BRN), basal root growth angle (BRGA) and root hair length (RHL). Common bean genotypes were planted in the field with low P for 45 days after planting (DAP) before evaluation. For the {sup 32}P study four contrasting genotypes for root hairs were grown for 28 DAP in the greenhouse using 15-20 liter pots filled with a mixture of sand and vermiculate as the growth media. The radioactive P was incorporated in the growth medium in the form of alumina-P fertilizer. Normal phosphorus (non-radioactive {sup 31}P) was included in the nutrient solution in the form of calcium phosphate, Ca{sub 3}(PO{sub 4}){sub 2}, and supplied through irrigation. Screened genotypes exhibited different root traits associated with P uptake efficiency, and that a given genotype can have one or more root traits responsible for it P uptake efficiency

  10. Uranium uptake by hydroponically cultivated crop plants

    Energy Technology Data Exchange (ETDEWEB)

    Soudek, Petr; Petrova, Sarka [Laboratory of Plant Biotechnologies, Joint Laboratory of Institute of Experimental Botany AS CR, v.v.i. and Crop Research Institute, v.v.i., Rozvojova 263, 162 05 Prague 6 (Czech Republic); Benesova, Dagmar [Laboratory of Plant Biotechnologies, Joint Laboratory of Institute of Experimental Botany AS CR, v.v.i. and Crop Research Institute, v.v.i., Rozvojova 263, 162 05 Prague 6 (Czech Republic); Faculty of Environment Technology, Institute of Chemical Technology, Technicka 5, 166 28 Prague 6 (Czech Republic); Dvorakova, Marcela [Laboratory of Plant Biotechnologies, Joint Laboratory of Institute of Experimental Botany AS CR, v.v.i. and Crop Research Institute, v.v.i., Rozvojova 263, 162 05 Prague 6 (Czech Republic); Vanek, Tomas, E-mail: vanek@ueb.cas.cz [Laboratory of Plant Biotechnologies, Joint Laboratory of Institute of Experimental Botany AS CR, v.v.i. and Crop Research Institute, v.v.i., Rozvojova 263, 162 05 Prague 6 (Czech Republic)

    2011-06-15

    Hydroponicaly cultivated plants were grown on medium containing uranium. The appropriate concentrations of uranium for the experiments were selected on the basis of a standard ecotoxicity test. The most sensitive plant species was determined to be Lactuca sativa with an EC{sub 50} value about 0.1 mM. Cucumis sativa represented the most resistant plant to uranium (EC{sub 50} = 0.71 mM). Therefore, we used the uranium in a concentration range from 0.1 to 1 mM. Twenty different plant species were tested in hydroponic solution supplemented by 0.1 mM or 0.5 mM uranium concentration. The uranium accumulation of these plants varied from 0.16 mg/g DW to 0.011 mg/g DW. The highest uranium uptake was determined for Zea mays and the lowest for Arabidopsis thaliana. The amount of accumulated uranium was strongly influenced by uranium concentration in the cultivation medium. Autoradiography showed that uranium is mainly localized in the root system of the plants tested. Additional experiments demonstrated the possibility of influencing the uranium uptake from the cultivation medium by amendments. Tartaric acid was able to increase uranium uptake by Brassica oleracea and Sinapis alba up to 2.8 times or 1.9 times, respectively. Phosphate deficiency increased uranium uptake up to 4.5 times or 3.9 times, respectively, by Brassica oleracea and S. alba. In the case of deficiency of iron or presence of cadmium ions we did not find any increase in uranium accumulation. - Highlights: > The uranium accumulation in twenty different plant species varied from 0.160 to 0.011 mg/g DW. > Uranium is mainly localized in the root system. > Tartaric acid was able to increase uranium uptake by Brassica oleracea and Sinapis alba. > The phosphates deficiency increase the uranium uptake.

  11. Uranium uptake by hydroponically cultivated crop plants

    International Nuclear Information System (INIS)

    Soudek, Petr; Petrova, Sarka; Benesova, Dagmar; Dvorakova, Marcela; Vanek, Tomas

    2011-01-01

    Hydroponicaly cultivated plants were grown on medium containing uranium. The appropriate concentrations of uranium for the experiments were selected on the basis of a standard ecotoxicity test. The most sensitive plant species was determined to be Lactuca sativa with an EC 50 value about 0.1 mM. Cucumis sativa represented the most resistant plant to uranium (EC 50 = 0.71 mM). Therefore, we used the uranium in a concentration range from 0.1 to 1 mM. Twenty different plant species were tested in hydroponic solution supplemented by 0.1 mM or 0.5 mM uranium concentration. The uranium accumulation of these plants varied from 0.16 mg/g DW to 0.011 mg/g DW. The highest uranium uptake was determined for Zea mays and the lowest for Arabidopsis thaliana. The amount of accumulated uranium was strongly influenced by uranium concentration in the cultivation medium. Autoradiography showed that uranium is mainly localized in the root system of the plants tested. Additional experiments demonstrated the possibility of influencing the uranium uptake from the cultivation medium by amendments. Tartaric acid was able to increase uranium uptake by Brassica oleracea and Sinapis alba up to 2.8 times or 1.9 times, respectively. Phosphate deficiency increased uranium uptake up to 4.5 times or 3.9 times, respectively, by Brassica oleracea and S. alba. In the case of deficiency of iron or presence of cadmium ions we did not find any increase in uranium accumulation. - Highlights: → The uranium accumulation in twenty different plant species varied from 0.160 to 0.011 mg/g DW. → Uranium is mainly localized in the root system. → Tartaric acid was able to increase uranium uptake by Brassica oleracea and Sinapis alba. → The phosphates deficiency increase the uranium uptake.

  12. Microstructure and property evolutions of titanium/nano-hydroxyapatite composites in-situ prepared by selective laser melting.

    Science.gov (United States)

    Han, Changjun; Wang, Qian; Song, Bo; Li, Wei; Wei, Qingsong; Wen, Shifeng; Liu, Jie; Shi, Yusheng

    2017-07-01

    Titanium (Ti)-hydroxyapatite (HA) composites have the potential for orthopedic applications due to their favorable mechanical properties, excellent biocompatibility and bioactivity. In this work, the pure Ti and nano-scale HA (Ti-nHA) composites were in-situ prepared by selective laser melting (SLM) for the first time. The phase, microstructure, surface characteristic and mechanical properties of the SLM-processed Ti-nHA composites were studied by X-ray diffraction, transmission electron microscope, atomic force microscope and tensile tests, respectively. Results show that SLM is a suitable method for fabricating the Ti-nHA composites with refined microstructure, low modulus and high strength. A novel microstructure evolution can be illustrated as: Relatively long lath-shaped grains of pure Ti evolved into short acicular-shaped and quasi-continuous circle-shaped grains with the varying contents of nHA. The elastic modulus of the Ti-nHA composites is 3.7% higher than that of pure Ti due to the effect of grain refinement. With the addition of 2% nHA, the ultimate tensile strength significantly reduces to 289MPa but still meets the application requirement of bone implants. The Ti-nHA composites exhibit a remarkable improvement of microhardness from 336.2 to 600.8 HV and nanohardness from 5.6 to 8.3GPa, compared to those of pure Ti. Moreover, the microstructure and property evolution mechanisms of the composites with the addition of HA were discussed and analyzed. It provides some new knowledge to the design and fabrication of biomedical material composites for bone implant applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Assessing participation in the ACL injured population: Selecting a patient reported outcome measure on the basis of measurement properties.

    Science.gov (United States)

    Letchford, Robert; Sparkes, Valerie; van Deursen, Robert W M

    2015-06-01

    A return to pre injury activity participation remains a common but often elusive goal following ACL injury. Investigations to improve our understanding of participation restrictions are limited by inconsistent use of insufficiently investigated measurement tools. The aim of this study was to follow the consensus based standards for the selection of health measurement instruments (COSMIN) guideline to provide a comparative evaluation of four patient reported outcomes (PROMs) on the basis of measurement properties. This will inform recommendations for measuring participation of ACL injured subjects, particularly in the United Kingdom (UK) National Health Service (NHS). Thirteen criteria were compiled from the COSMIN guideline. These included reliability, measurement error, content validity, construct validity, responsiveness and interpretability. Data from 51 subjects collected as part of a longitudinal observational study of recovery over the first year following ACLR was used in the analysis. Of the thirteen criteria, the required standard was met in 11 for Tegner, 11 for International Knee Documentation Committee (IKDC), 6 for Cincinnati Sports Activity Scale (CSAS) and 6 for Marx. The two weaknesses identified for the Tegner are more easily compensated for during interpretation than those in the IKDC; for this reason the Tegner is the recommended PROM. The Tegner activity rating scale performed consistently well in respect of all measurement properties in this sample, with clear benefits over the other PROMs. The measurement properties presented should be used to inform implementation and interpretation of this outcome measure in clinical practice and research. Level II prospective study. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. The pharmacology of TD-8954, a potent and selective 5-HT4 receptor agonist with gastrointestinal prokinetic properties

    Directory of Open Access Journals (Sweden)

    David T Beattie

    2011-05-01

    Full Text Available This study evaluated the in vitro and in vivo pharmacological properties of TD-8954, a potent and selective 5-HT4 receptor agonist. TD-8954 had high affinity (pKi = 9.4 for human recombinant 5-HT4(c (h5-HT4(c receptors, and selectivity (> 2,000-fold over all other 5-HT receptors and non-5-HT receptors, ion channels, enzymes and transporters tested (n = 78. TD-8954 produced an elevation of cAMP in HEK-293 cells expressing the h5-HT4(c receptor (pEC50 = 9.3, and contracted the guinea pig colonic longitudinal muscle/myenteric plexus (LMMP preparation (pEC50 = 8.6. TD-8954 had moderate intrinsic activity (IA in the in vitro assays. In conscious guinea pigs, subcutaneous (s.c. administration of TD 8954 (0.03 - 3 mg/kg increased the colonic transit of carmine red dye, reducing the time taken for its excretion. Following intraduodenal (i.d. dosing to anesthetized rats, TD 8954 (0.03 - 10 mg/kg evoked a dose-dependent relaxation of the esophagus. Following oral administration to conscious dogs, TD 8954 (10 and 30 µg/kg produced an increase in contractility of the antrum, duodenum and jejunum. In a single ascending oral dose study in healthy human subjects, TD-8954 (0.1 - 20 mg increased bowel movement frequency and reduced the time to first stool. It is concluded that TD-8954 is a potent and selective 5-HT4 receptor agonist in vitro, with robust in vivo stimulatory activity in the gastrointestinal (GI tract of guinea pigs, rats, dogs and humans. TD-8954 may have clinical utility in patients with disorders of reduced GI motility.

  15. In vitro screening of selected probiotic properties of Lactobacillus strains isolated from traditional fermented cabbage and cucumber.

    Science.gov (United States)

    Zielińska, Dorota; Rzepkowska, Anna; Radawska, Anna; Zieliński, Konrad

    2015-02-01

    Most important during probiotic selection are gastric acid and bile tolerance, the adhesion to the luminal epithelium to colonize the lower gastrointestinal tract of a human and safety for human consumption. The aim of this study was to evaluate the selected probiotic in vitro properties of Lactobacillus spp. Strains isolated from traditional fermented food. A total 38 strains were isolated from the pickled samples and 14 were identified as Lactobacillus spp. The survival of almost all strains after incubation at pH 2.5 did not change markedly, and remained at above 90 % (10(9) CFU/mL). The strains also exhibited a high survival rate at pH 3.5 (>90 %), whereas pH 1.5 all were died. Just four strains could survive 90 min. at pH 1.5 (survival rates of 81-94 % after 24 h, whereas after incubation in 2 and 4 % bile salt solution it was 59-94 %. All tested strains showed very good and good resistance to 0.4 % phenol addition, however only Lb. johnsonii K4 was able to multiply. The hydrophobic nature of the cell surface of the tested strains was moderated recording hydrophobicity of Lb. johnsonii K4 and Lb. rhamnosus K3 above 60 %. Safety evaluation excluded four of tested strains as candidate probiotics, according to antibiotic resistance patterns and certain metabolic activities. On the basis on the results 10 of the selected Lactobacillus strains are safe and can survive under gastrointestinal conditions, which requires them to future in vitro and in vivo probiotic studies.

  16. Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties

    International Nuclear Information System (INIS)

    Vrancken, Bey; Thijs, Lore; Kruth, Jean-Pierre; Van Humbeeck, Jan

    2012-01-01

    Highlights: ► Responses of SLM-produced and wrought Ti6Al4V to heat treatment are compared. ► Temperature is found to be the controlling parameter for treatments in the α + β range. ► Ductility could be improved by a factor of 85%, from 7.27% to 13.59%. ► An optimal heat treatment for SLM produced Ti6Al4V is proposed. - Abstract: The present work shows that optimization of mechanical properties via heat treatment of parts produced by Selective Laser Melting (SLM) is profoundly different compared to conventionally processed Ti6Al4V. In order to obtain optimal mechanical properties, specific treatments are necessary due to the specific microstructure resulting from the SLM process. SLM is an additive manufacturing technique through which components are built by selectively melting powder layers with a focused laser beam. The process is characterized by short laser-powder interaction times and localized high heat input, which leads to steep thermal gradients, rapid solidification and fast cooling. In this research, the effect of several heat treatments on the microstructure and mechanical properties of Ti6Al4V processed by SLM is studied. A comparison is made with the effect of these treatments on hot forged and subsequently mill annealed Ti6Al4V with an original equiaxed microstructure. For SLM produced parts, the original martensite α′ phase is converted to a lamellar mixture of α and β for heat treating temperatures below the β-transus (995 °C), but features of the original microstructure are maintained. Treated above the β-transus, extensive grain growth occurs and large β grains are formed which transform to lamellar α + β upon cooling. Post treating at 850 °C for 2 h, followed by furnace cooling increased the ductility of SLM parts to 12.84 ± 1.36%, compared to 7.36 ± 1.32% for as-built parts.

  17. Exosomes: Mechanisms of Uptake

    Directory of Open Access Journals (Sweden)

    Kelly J. McKelvey

    2015-07-01

    Full Text Available Exosomes are 30–100 nm microvesicles which contain complex cellular signals of RNA, protein and lipids. Because of this, exosomes are implicated as having limitless therapeutic potential for the treatment of cancer, pregnancy complications, infections, and autoimmune diseases. To date we know a considerable amount about exosome biogenesis and secretion, but there is a paucity of data regarding the uptake of exosomes by immune and non-immune cell types (e.g., cancer cells and the internal signalling pathways by which these exosomes elicit a cellular response. Answering these questions is of paramount importance.

  18. Exosomes: Mechanisms of Uptake

    Directory of Open Access Journals (Sweden)

    Kelly J. McKelvey

    2015-07-01

    Full Text Available Exosomes are 30–100 nm microvesicles which contain complex cellular signals of RNA, protein and lipids. Because of this, exosomes are implicated as having limitless therapeutic potential for the treatment of cancer, pregnancy complications, infections, and autoimmune diseases. To date we know a considerable amount about exosome biogenesis and secretion, but there is a paucity of data regarding the uptake of exosomes by immune and non- immune cell types (e.g., cancer cells and the internal signalling pathways by which these exosomes elicit a cellular response. Answering these questions is of para‐ mount importance.

  19. Thyroid Uptake Measurement System

    International Nuclear Information System (INIS)

    Nguyen Duc Tuan; Nguyen Thi Bao My; Nguyen Van Sy

    2007-01-01

    The NED-UP.M7 is a complete thyroid uptake and analysis system specifically designed for nuclear medicine. Capable of performing a full range of studies this system provides fast, accurate results for Uptake Studies. The heart of the NED-UP.M7 is a microprocessor-controlled 2048 channel Compact Multi-Channel Analyzer, coupled to a 2 inch x 2 inch NaI(Tl) detector with a USB personal computer interface. The system offers simple, straight-forward operation using pre-programmed isotopes, and menudriven prompts to guide the user step by step through each procedure. The pre-programmed radionuclides include I-123, I-125, I-131, Tc-99m and Cs-137. The user-defined radionuclides also allow for isotope identification while the printer provides hard copy printouts for patient and department record keeping. The included software program running on PC (Windows XP-based) is a user friendly program with menudriven and graphic interface for easy controlling the system and managing measurement results of patient on Excel standard form. (author)

  20. Uptake properties of Ni2+ by nCaO.Al2O3.2SiO2 (n=1-4) prepared from solid-state reaction of kaolinite and calcite.

    Science.gov (United States)

    Jha, Vinay Kumar; Kameshima, Yoshikazu; Nakajima, Akira; Okada, Kiyoshi; MacKenzie, Kenneth J D

    2005-08-31

    A series of nCaO.Al2O3.2SiO2 samples (n=1-4) were prepared by solid-state reaction of mechanochemically treated mixtures of kaolinite and calcite fired at 600-1000 degrees C for 24 h. All the samples were X-ray amorphous after firing at 600-800 degrees C but had crystallized by 900 degrees C. The main crystalline phases were anorthite (n=1), gehlenite (n=2 and 3) and larnite (n=4). The uptake of Ni2+ by nCaO.Al2O3.2SiO2 samples fired at 800 and 900 degrees C was investigated at room temperature using solutions with initial Ni2+ concentrations of 0.1-50 mmol/l. Amorphous samples (fired at 800 degrees C) showed a higher Ni2+ uptake capacity than crystalline samples (fired at 900 degrees C). Ni2+ uptake was found to increase with increasing of CaO content. Amorphous 4CaO.Al2O3.2SiO2 showed the highest Ni2+ uptake capacity (about 9 mmol/g). The Ni2+ uptake abilities of the present samples are higher than those of other materials reported in the literature. Since the sorbed Ni2+/released Ca2+ ratios of these samples are close to unity, ion replacement of Ni2+ for Ca2+ is thought to be the principal mechanism of Ni2+ uptake by the present samples.

  1. Uptake mechanism for iodine species to black carbon.

    Science.gov (United States)

    Choung, Sungwook; Um, Wooyong; Kim, Minkyung; Kim, Min-Gyu

    2013-09-17

    Natural organic matter (NOM) plays an important role in determining the fate and transport of iodine species such as iodide (I(-)) and iodate (IO3(-)) in groundwater system. Although NOM exists as diverse forms in environments, prior iodine studies have mainly focused on uptake processes of iodide and iodate to humic materials. This study was conducted to determine the iodide and iodate uptake potential for a particulate NOM (i.e., black carbon [BC]). A laboratory-produced BC and commercial humic acid were used for batch experiments to compare their iodine uptake properties. The BC exhibited >100 times greater uptake capability for iodide than iodate at low pH of ~3, while iodide uptake was negligible for the humic acid. The uptake properties of both solids strongly depend on the initial iodine aqueous concentrations. After uptake reaction of iodide to the BC, X-ray absorption fine structure spectroscopy results indicated that the iodide was converted to electrophilic species, and iodine was covalently bound to carbon atom in polycyclic aromatic hydrocarbons present in the BC. The computed distribution coefficients (i.e., Kd values) suggest that the BC materials retard significantly the transport of iodide at low pH in environmental systems containing even a small amount of BC.

  2. Antioxidant and antidiabetic properties of condensed tannins in acetonic extract of selected raw and processed indigenous food ingredients from Kenya.

    Science.gov (United States)

    Kunyanga, Catherine Nkirote; Imungi, Jasper Kathenya; Okoth, Michael; Momanyi, Clare; Biesalski, Han Konrad; Vadivel, Vellingiri

    2011-05-01

    Recently, tannins have received considerable attention as health-promoting component in various plant foods and several studies have reported on its nutraceutical properties. However, no study has established the role of condensed tannins in indigenous foods of Kenya. Therefore, this study was designed to evaluate the antioxidant activity (DPPH and FRAP) and antidiabetic effects (α-amylase and α-glucosidase inhibition activities) of condensed tannins in some selected raw and traditionally processed indigenous cereals, legumes, oil seeds, and vegetables. The condensed tannin content of the grains and vegetables ranged between 2.55 and 4.35 g/100 g DM and 1.53 and 5.73 g/100 g DM, respectively. The scavenging effect of acetonic extract on DPPH radical ranged from 77% to 90% while the reducing power was found to be 31 to 574 mmol Fe(II)/g DM in all the investigated food ingredients. The condensed tannin extracts of the analyzed samples showed promising antidiabetic effects with potential α-amylase and α-glucosidase inhibition activities of 23% to 44% and 58% to 88%, respectively. Condensed tannins extracted from the amaranth grain, finger millet, field bean, sunflower seeds, drumstick, and amaranth leaves exerted significantly higher antioxidant and antidiabetic activities than other food ingredients. Among the traditional processing methods, roasting of grains and cooking of vegetables were found to be more suitable mild treatments for preserving the tannin compound and its functional properties as opposed to soaking + cooking and blanching treatments. The identified elite sources of optimally processed indigenous food ingredients with promising results could be used as health-promoting ingredients through formulation of therapeutic diets. © 2011 Institute of Food Technologists®

  3. Impacts of intellectual property rights on marker-assisted selection research and application for agriculture in developing countries

    International Nuclear Information System (INIS)

    Henson-Apollonio, V.

    2007-01-01

    Although the impact of marker-assisted selection (MAS) in commercial and public sector breeding programmes in developing countries is to date limited to a few crops and traits, the potential benefits of using markers linked to genes of interest in breeding programmes for improving the productivity of crops, livestock, forest trees and farmed fish is substantial. While more recent methods associated with the use of MAS are technically demanding and often expensive, most applications of basic MAS were initially described in the literature, and thus will likely have very few intellectual property (IP) restrictions associated with their use, irrespective of the agricultural sector involved. For example, isolating DNA, amplifying specific gene sequences from that DNA (with most available primers), separating fragments using gel/polyacrylamide electrophoresis and imaging of fragments with standard techniques are likely to be available without restriction to scientists and breeders in the developing world, even as part of a commercial service. Problems arise when there is a need to use or develop high-throughput modes, which require more sophisticated technologies. For high-throughput use, a breeder will want to use the most efficient techniques that are currently available. This means that the more advanced processes/methods, reagents, software applications/simulations and equipment, which provide the most effective means to exploit MAS fully, are most likely covered by intellectual property rights (IPRs) such as patent rights, confidential information (trade secrets) and copyrights, both in industrialized countries and also in many developing countries such as Brazil, China and India. In situations where breeders wish to use cutting edge technologies and the most efficient markers, care must be taken to avoid activities that may infringe IPRs when using MAS methodologies. (author)

  4. Spectral properties of the narrow-line region in Seyfert galaxies selected from the SDSS-DR7

    Science.gov (United States)

    Vaona, L.; Ciroi, S.; Di Mille, F.; Cracco, V.; La Mura, G.; Rafanelli, P.

    2012-12-01

    Although the properties of the narrow-line region (NLR) of active galactic nuclei (AGN) have been deeply studied by many authors in the past three decades, many questions are still open. The main goal of this work is to explore the NLR of Seyfert galaxies by collecting a large statistical spectroscopic sample of Seyfert 2 and Intermediate-type Seyfert galaxies having a high signal-to-noise ratio in order to take advantage of a high number of emission lines to be accurately measured. 2153 Seyfert 2 and 521 Intermediate-type Seyfert spectra were selected from Sloan Digital Sky Survey Data Release 7 (SDSS-DR7) with a diagnostic diagram based on the oxygen emission-line ratios. All the emission lines, broad components included, were measured by means of a self-developed code, after the subtraction of the stellar component. Physical parameters, such as internal reddening, ionization parameter, temperature, density, gas and stellar velocity dispersion were determined for each object. Furthermore, we estimated mass and radius of the NLR, kinetic energy of the ionized gas and black hole accretion rate. From the emission-line analysis and the estimated physical properties, it appears that the NLR is similar in Seyfert 2 and Intermediate-Seyfert galaxies. The only differences, lower extinction, gas kinematics in general not dominated by the host galaxy gravitational potential and higher percentage of [O III]λ5007 blue asymmetries in Intermediate-Seyfert, can be ascribed to an effect of inclination of our line of sight with respect to the torus axis.

  5. Obscured AGN at z similar to 1 from the zCOSMOS-Bright Survey : I. Selection and optical properties of a [Ne v]-selected sample

    NARCIS (Netherlands)

    Mignoli, M.; Vignali, C.; Gilli, R.; Comastri, A.; Zamorani, G.; Bolzonella, M.; Bongiorno, A.; Lamareille, F.; Nair, P.; Pozzetti, L.; Lilly, S. J.; Carollo, C. M.; Contini, T.; Kneib, J. -P.; Le Fevre, O.; Mainieri, V.; Renzini, A.; Scodeggio, M.; Bardelli, S.; Caputi, K.; Cucciati, O.; de la Torre, S.; de Ravel, L.; Franzetti, P.; Garilli, B.; Iovino, A.; Kampczyk, P.; Knobel, C.; Kovac, K.; Le Borgne, J. -F.; Le Brun, V.; Maier, C.; Pello, R.; Peng, Y.; Montero, E. Perez; Presotto, V.; Silverman, J. D.; Tanaka, M.; Tasca, L.; Tresse, L.; Vergani, D.; Zucca, E.; Bordoloi, R.; Cappi, A.; Cimatti, A.; Koekemoer, A. M.; McCracken, H. J.; Moresco, M.; Welikala, N.

    Aims. The application of multi-wavelength selection techniques is essential for obtaining a complete and unbiased census of active galactic nuclei (AGN). We present here a method for selecting z similar to 1 obscured AGN from optical spectroscopic surveys. Methods. A sample of 94 narrow-line AGN

  6. Selective synthesis and characterization of chlorins as sensitizers for photodynamic therapy

    Science.gov (United States)

    Montforts, Franz-Peter; Kusch, Dirk; Hoper, Frank; Braun, Stefan; Gerlach, Benjamin; Brauer, Hans-Dieter; Schermann, Guido; Moser, Joerg G.

    1996-04-01

    Chlorin type sensitizers have ideal photophysical properties for an application in PDT. The basic chlorin framework of these sensitizers has to be modified by attachment of lipophilic and hydrophilic residues to achieve a good cell uptake and tumor enrichment. In the present study we describe the selective synthesis of amphiphilic chlorins starting from the readily accessible red blood pigment heme. The photophysical properties of the well defined synthetic chlorins are characterized by photophysical investigations. The kinetic of cell uptake, the localization in the cell and the photodynamic behavior of the amphiphilic sensitizers are demonstrated by incubation of A 375 cancer cell lines with structurally different chlorins.

  7. Selective extraction of americium(III) over europium(III) ions with pyridylpyrazole ligands. Structure-property relationships

    Energy Technology Data Exchange (ETDEWEB)

    Su, Dongping; Liu, Ying; Li, Shimeng; Ding, Songdong; Jin, Yongdong; Wang, Zhipeng; Hu, Xiaoyang; Zhang, Lirong [Department of chemistry, Sichuan University, Chengdu (China)

    2017-01-18

    To clarify the structure-property relationships of pyridylpyrazole ligands and provide guidance for the design of new and more efficient ligands for the selective extraction of actinides over lanthanides, a series of alkyl-substituted pyridylpyrazole ligands with different branched chains at different positions of the pyrazole ring were synthesized. Extraction experiments showed that the pyridylpyrazole ligands exhibited good selective extraction abilities for Am{sup III} ions, and the steric effects of the branched chain had a significant impact on the distribution ratios of Am{sup III} and Eu{sup III} ions as well as the separation factor. Moreover, both slope analyses and UV/Vis spectrometry titrations indicated the formation of a 1:1 complex of 2-(1-octyl-1H-pyrazol-3-yl)pyridine (C8-PypzH) with Eu{sup III} ions. The stability constant (log K) for this complex obtained from the UV/Vis titration was 4.45 ± 0.04. Single crystals of the complexes of 3-(2-pyridyl)pyrazole (PypzH) with Eu(NO{sub 3}){sub 3} and Sm(NO{sub 3}){sub 3} were obtained; PypzH acts as a bidentate ligand in the crystal structures, and the N atom with a bound H atom did not participate in the coordination. In general, this study revealed some interesting findings on the effects of the alkyl-chain structure and the special complexation between pyridylpyrazole ligands and Ln{sup III} ions. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. Zirconium intermetallics and hydrogen uptake during corrosion

    International Nuclear Information System (INIS)

    Cox, B.

    1987-04-01

    The routes by which hydrogen can enter zirconium alloys containing second phase particles during corrosion are discussed. Both direct diffusion through the bulk of the oxide film, and migration through second phase particles that intersect the surface are considered. An examination of results for hydrogen uptake by zirconium alloys during the early stages of oxidation, when the oxide film is still coherent, suggests that for Zr, Zr-1%Cu and Zr-1%Fe the hydrogen enters by diffusing through the bulk ZrO 2 film, whereas for the Zircaloys the primary migration route may be through the intermetallics. The steps in the latter process are discussed and the evidence available on the properties of the intermetallics collated. A comparison of these data with results for hydrogen uptake by two series of ternary alloys (Zr-1%Nb - 1%X, Zr-1%Cu - 1%X) suggests that high hydrogen uptakes often correlate with intermetallics with high hydrogen solubilities and vice versa. The properties of Zr(Fe/Cr) 2+x intermetallics are examined in an attempt to understand the behaviour of the Zircaloys, and it is concluded that present data establishing composition and unit cell dimensions for such intermetallic particles are not of sufficient accuracy to permit a correlation

  9. Structure and mechanical properties of parts obtained by selective laser melting of metal powder based on intermetallic compounds Ni3Al

    Science.gov (United States)

    Smelov, V. G.; Sotov, A. V.; Agapovichev, A. V.; Nosova, E. A.

    2018-03-01

    The structure and mechanical properties of samples are obtained from metal powder based on intermetallic compound by selective laser melting. The chemical analysis of the raw material and static tensile test of specimens were made. Change in the samples’ structure and mechanical properties after homogenization during four and twenty-four hours were investigated. A small-sized combustion chamber of a gas turbine engine was performed by the selective laser melting method. The print combustion chamber was subjected to the gas-dynamic test in a certain temperature and time range.

  10. A Comparison of Predictive Thermo and Water Solvation Property Prediction Tools and Experimental Data for Selected Traditional Chemical Warfare Agents and Simulants II: COSMO RS and COSMOTherm

    Science.gov (United States)

    2017-04-01

    SELECTED TRADITIONAL CHEMICAL WARFARE AGENTS AND SIMULANTS II: COSMO-RS AND COSMOTHERM ECBC-TR-1454 Jerry B. Cabalo RESEARCH AND TECHNOLOGY...Traditional Chemical Warfare Agents and Simulants II: COSMO-RS and COSMOTherm 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER CB10115...in the ADF 2012 suite of programs for the physico- chemical properties of a set of traditional chemical warfare agents and selected simulants. To

  11. Magnetic properties of some selected, soil-related iron oxides and oxyhydroxides as probed by 57Fe Moessbauer spectroscopy

    International Nuclear Information System (INIS)

    DeGrave, E.; Vandenberghe, R.E.; Bowen, L.H.

    1990-01-01

    In the last decade, Mossbauer spectroscopy has become an increasingly important and applied analytical tool for the characterization of environmental Fe-containing material. One of the most fastly growing application area of this technique is undoubtedly that of soils and sediments. Since such systems are commonly complex mixtures of various and mostly poorly crystalline compounds, much emphasis has been displayed towards the Mossbauer spectra of the pure constituents which, in the case of oxides and oxyhydroxides, usually concern well characterized synthetic samples. Many excellent and fairly complete review papers in that respect have been published in the recent literature and it is not the aim of the present authors to come up with still another one covering the same period. Only those results reported since 1985 and which have provided basically new insight concerning structural and/or magnetic properties have been selected. In addition, it has been attempted to collect some of the less-frequently dealt-with magnetic characteristics which more often have a fundamental importance rather than an analytical one, and which are therefore at the moment less-directly related and restricted to soil studies. A particular aspect that has received considerable attention in this paper is the effect on the Mossbauer spectra of the application of strong magnetic fields

  12. Glass and Glass-Ceramic Materials from Simulated Composition of Lunar and Martian Soils: Selected Properties and Potential Applications

    Science.gov (United States)

    Ray, C. S.; Sen, S.; Reis, S. T.; Kim, C. W.

    2005-01-01

    In-situ resource processing and utilization on planetary bodies is an important and integral part of NASA's space exploration program. Within this scope and context, our general effort is primarily aimed at developing glass and glass-ceramic type materials using lunar and martian soils, and exploring various applications of these materials for planetary surface operations. Our preliminary work to date have demonstrated that glasses can be successfully prepared from melts of the simulated composition of both lunar and martian soils, and the melts have a viscosity-temperature window appropriate for drawing continuous glass fibers. The glasses are shown to have the potential for immobilizing certain types of nuclear wastes without deteriorating their chemical durability and thermal stability. This has a direct impact on successfully and economically disposing nuclear waste generated from a nuclear power plant on a planetary surface. In addition, these materials display characteristics that can be manipulated using appropriate processing protocols to develop glassy or glass-ceramic magnets. Also discussed in this presentation are other potential applications along with a few selected thermal, chemical, and structural properties as evaluated up to this time for these materials.

  13. Bulgeless galaxies at intermediate redshift: Sample selection, color properties, and the existence of powerful active galactic nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Bizzocchi, Luca; Leonardo, Elvira; Grossi, Marco; Afonso, José; Fernandes, Cristina; Retrê, João [Centro de Astronomia e Astrofísica da Universidade de Lisboa, Observatório Astronómico de Lisboa, Tapada da Ajuda, 1349-018 Lisbon (Portugal); Filho, Mercedes E.; Lobo, Catarina [Centro de Astrofísica da Universidade do Porto, Rua das Estrelas, 4150-762 Porto (Portugal); Griffith, Roger L. [Infrared Processing and Analysis Center, California Institute of Technology, Pasadena, CA 91125 (United States); Anton, Sonia [Centro de Investigação em Ciências Geo-Espaciais, Faculdade de Ciências da Universidade do Porto, Porto (Portugal); Bell, Eric F. [Department of Astronomy, University of Michigan, 500 Church Street, Ann Arbor, MI 48109 (United States); Brinchmann, Jarle [Leiden Observatory, Leiden University, P.O. Box 9513, NL-2300 RA Leiden (Netherlands); Henriques, Bruno [Max-Planck-Institut für Astrophysik, Karl Schwarzschild Straße 1, D-85748 Garching bei München (Germany); Messias, Hugo [Departamento de astronomía, Av. Esteban Iturra 6to piso, Facultad de Ciencias Físicas y Matemáticas, Universidad de Concepción (Chile)

    2014-02-10

    We present a catalog of bulgeless galaxies, which includes 19,225 objects