WorldWideScience

Sample records for selection ratios criterion

  1. Selecting Items for Criterion-Referenced Tests.

    Science.gov (United States)

    Mellenbergh, Gideon J.; van der Linden, Wim J.

    1982-01-01

    Three item selection methods for criterion-referenced tests are examined: the classical theory of item difficulty and item-test correlation; the latent trait theory of item characteristic curves; and a decision-theoretic approach for optimal item selection. Item contribution to the standardized expected utility of mastery testing is discussed. (CM)

  2. Value of prostate specific antigen and prostatic volume ratio (PSA/V) as the selection criterion for US-guided prostatic biopsy

    International Nuclear Information System (INIS)

    Veneziano, S.; Paulica, P.; Querze', R.; Viglietta, G.; Trenta, A.

    1991-01-01

    US-guided biopsy was performed in 94 patients with suspected lesions at transerectal US. Histology demonstrated carcinoma in 43 cases, benign hyperplasia in 44, and prostatis in 7. In all cases the prostate specific antigen (PSA) was calculated, by means of US, together with prostatic volume (v). PSA was related to the corresponding gland volume, which resulted in PSA/V ratio. Our study showed PSA/V ration to have higher sensitivity and specificity than absolulute PSA value in the diagnosis of prostatic carcinoma. The authors believe prostate US-guided biopsy to be: a) necessary when the suspected area has PSA/V ratio >0.15, and especially when PSA/V >0.30; b) not indicated when echo-structural alterations are associated with PSA/V <0.15, because they are most frequently due to benign lesions. The combined use of PSA/V ratio and US is therefore suggested to select the patients in whom biopsy is to be performed

  3. A criterion for selecting renewable energy processes

    International Nuclear Information System (INIS)

    Searcy, Erin; Flynn, Peter C.

    2010-01-01

    We propose that minimum incremental cost per unit of greenhouse gas (GHG) reduction, in essence the carbon credit required to economically sustain a renewable energy plant, is the most appropriate social criterion for choosing from a myriad of alternatives. The application of this criterion is illustrated for four processing alternatives for straw/corn stover: production of power by direct combustion and biomass integrated gasification and combined cycle (BIGCC), and production of transportation fuel via lignocellulosic ethanol and Fischer Tropsch (FT) syndiesel. Ethanol requires a lower carbon credit than FT, and direct combustion a lower credit than BIGCC. For comparing processes that make a different form of end use energy, in this study ethanol vs. electrical power via direct combustion, the lowest carbon credit depends on the relative values of the two energy forms. When power is 70$ MW h -1 , ethanol production has a lower required carbon credit at oil prices greater than 600$ t -1 (80$ bbl -1 ). (author)

  4. Integral criterion for selecting nonlinear crystals for frequency conversion

    International Nuclear Information System (INIS)

    Grechin, Sergei G

    2009-01-01

    An integral criterion, which takes into account all parameters determining the conversion efficiency, is offered for selecting nonlinear crystals for frequency conversion. The angular phase-matching width is shown to be related to the beam walk-off angle. (nonlinear optical phenomena)

  5. Interface Pattern Selection Criterion for Cellular Structures in Directional Solidification

    Science.gov (United States)

    Trivedi, R.; Tewari, S. N.; Kurtze, D.

    1999-01-01

    The aim of this investigation is to establish key scientific concepts that govern the selection of cellular and dendritic patterns during the directional solidification of alloys. We shall first address scientific concepts that are crucial in the selection of interface patterns. Next, the results of ground-based experimental studies in the Al-4.0 wt % Cu system will be described. Both experimental studies and theoretical calculations will be presented to establish the need for microgravity experiments.

  6. A Variance Minimization Criterion to Feature Selection Using Laplacian Regularization.

    Science.gov (United States)

    He, Xiaofei; Ji, Ming; Zhang, Chiyuan; Bao, Hujun

    2011-10-01

    In many information processing tasks, one is often confronted with very high-dimensional data. Feature selection techniques are designed to find the meaningful feature subset of the original features which can facilitate clustering, classification, and retrieval. In this paper, we consider the feature selection problem in unsupervised learning scenarios, which is particularly difficult due to the absence of class labels that would guide the search for relevant information. Based on Laplacian regularized least squares, which finds a smooth function on the data manifold and minimizes the empirical loss, we propose two novel feature selection algorithms which aim to minimize the expected prediction error of the regularized regression model. Specifically, we select those features such that the size of the parameter covariance matrix of the regularized regression model is minimized. Motivated from experimental design, we use trace and determinant operators to measure the size of the covariance matrix. Efficient computational schemes are also introduced to solve the corresponding optimization problems. Extensive experimental results over various real-life data sets have demonstrated the superiority of the proposed algorithms.

  7. Exclusion as a Criterion for Selecting Socially Vulnerable Population Groups

    Directory of Open Access Journals (Sweden)

    Aleksandra Anatol’evna Shabunova

    2016-05-01

    Full Text Available The article considers theoretical aspects of a scientific research “The Mechanisms for Overcoming Mental Barriers of Inclusion of Socially Vulnerable Categories of the Population for the Purpose of Intensifying Modernization in the Regional Community” (RSF grant No. 16-18-00078. The authors analyze the essence of the category of “socially vulnerable groups” from the legal, economic and sociological perspectives. The paper shows that the economic approach that uses the criterion “the level of income and accumulated assets” when defining vulnerable population groups prevails in public administration practice. The legal field of the category based on the economic approach is defined by the concept of “the poor and socially unprotected categories of citizens”. With the help of the analysis of theoretical and methodological aspects of this issue, the authors show that these criteria are a necessary but not sufficient condition for classifying the population as being socially vulnerable. Foreign literature associates the phenomenon of vulnerability with the concept of risks, with the possibility of households responding to them and with the likelihood of losing the well-being (poverty theory; research areas related to the means of subsistence, etc.. The asset-based approaches relate vulnerability to the poverty that arises due to lack of access to tangible and intangible assets. Sociological theories presented by the concept of social exclusion pay much attention to the breakdown of social ties as a source of vulnerability. The essence of social exclusion consists in the inability of people to participate in important aspects of social life (in politics, labor markets, education and healthcare, cultural life, etc. though they have all the rights to do so. The difference between the concepts of exclusion and poverty is manifested in the displacement of emphasis from income inequality to limited access to rights. Social exclusion is

  8. Sperm head's birefringence: a new criterion for sperm selection.

    Science.gov (United States)

    Gianaroli, Luca; Magli, M Cristina; Collodel, Giulia; Moretti, Elena; Ferraretti, Anna P; Baccetti, Baccio

    2008-07-01

    To investigate the characteristics of birefringence in human sperm heads and apply polarization microscopy for sperm selection at intracytoplasmic sperm injection (ICSI). Prospective randomized study. Reproductive Medicine Unit, Società Italiana Studi Medicina della Riproduzione, Bologna, Italy. A total of 112 male patients had birefringent sperm selected for ICSI (study group). The clinical outcome was compared with that obtained in 119 couples who underwent a conventional ICSI cycle (control group). The proportion of birefringent spermatozoa was evaluated before and after treatment in relation to the sperm sample quality. Embryo development and clinical outcome in the study group were compared with those in the controls. Proportion of birefringent sperm heads, rates of fertilization, cleavage, pregnancy, implantation, and ongoing implantation. The proportion of birefringent spermatozoa was significantly higher in normospermic samples when compared with oligoasthenoteratospermic samples with no progressive motility and testicular sperm extraction samples. Although fertilization and cleavage rates did not differ between the study and control groups, in the most severe male factor condition (oligoasthenoteratospermic with no progressive motility and testicular sperm extraction), the rates of clinical pregnancy, ongoing pregnancy, and implantation were significantly higher in the study group versus the controls. The analysis of birefringence in the sperm head could represent both a diagnostic tool and a novel method for sperm selection.

  9. 76 FR 15961 - Funding Priorities and Selection Criterion; Disability and Rehabilitation Research Projects and...

    Science.gov (United States)

    2011-03-22

    ... priorities and a selection criterion for the Disability and Rehabilitation Research Projects and Centers... outcomes for underserved populations; (4) identify research gaps; (5) identify mechanisms of integrating research and practice; and (6) disseminate findings. This notice proposes two priorities and a selection...

  10. Covariance-Based Measurement Selection Criterion for Gaussian-Based Algorithms

    Directory of Open Access Journals (Sweden)

    Fernando A. Auat Cheein

    2013-01-01

    Full Text Available Process modeling by means of Gaussian-based algorithms often suffers from redundant information which usually increases the estimation computational complexity without significantly improving the estimation performance. In this article, a non-arbitrary measurement selection criterion for Gaussian-based algorithms is proposed. The measurement selection criterion is based on the determination of the most significant measurement from both an estimation convergence perspective and the covariance matrix associated with the measurement. The selection criterion is independent from the nature of the measured variable. This criterion is used in conjunction with three Gaussian-based algorithms: the EIF (Extended Information Filter, the EKF (Extended Kalman Filter and the UKF (Unscented Kalman Filter. Nevertheless, the measurement selection criterion shown herein can also be applied to other Gaussian-based algorithms. Although this work is focused on environment modeling, the results shown herein can be applied to other Gaussian-based algorithm implementations. Mathematical descriptions and implementation results that validate the proposal are also included in this work.

  11. Accuracy of a selection criterion for glass forming ability in the Ni–Nb–Zr system

    International Nuclear Information System (INIS)

    Déo, L.P.; Oliveira, M.F. de

    2014-01-01

    Highlights: • We applied a selection in the Ni–Nb–Zr system to find alloys with high GFA. • We used the thermal parameter γ m to evaluate the GFA of alloys. • The correlation between the γ m parameter and R c in the studied system is poor. • The effect of oxygen impurity reduced dramatically the GFA of alloys. • Unknown intermetallic compounds reduced the accuracy of the criterion. - Abstract: Several theories have been developed and applied in metallic systems in order to find the best stoichiometries with high glass forming ability; however there is no universal theory to predict the glass forming ability in metallic systems. Recently a selection criterion was applied in the Zr–Ni–Cu system and it was found some correlation between experimental and theoretical data. This criterion correlates critical cooling rate for glass formation with topological instability of stable crystalline structures; average work function difference and average electron density difference among the constituent elements of the alloy. In the present work, this criterion was applied in the Ni–Nb–Zr system. It was investigated the influence of factors not considered in the calculation and on the accuracy of the criterion, such as unknown intermetallic compounds and oxygen contamination. Bulk amorphous specimens were produced by injection casting. The amorphous nature was analyzed by X-ray diffraction and differential scanning calorimetry; oxygen contamination was quantified by the inert gas fusion method

  12. A new diagnostic accuracy measure and cut-point selection criterion.

    Science.gov (United States)

    Dong, Tuochuan; Attwood, Kristopher; Hutson, Alan; Liu, Song; Tian, Lili

    2017-12-01

    Most diagnostic accuracy measures and criteria for selecting optimal cut-points are only applicable to diseases with binary or three stages. Currently, there exist two diagnostic measures for diseases with general k stages: the hypervolume under the manifold and the generalized Youden index. While hypervolume under the manifold cannot be used for cut-points selection, generalized Youden index is only defined upon correct classification rates. This paper proposes a new measure named maximum absolute determinant for diseases with k stages ([Formula: see text]). This comprehensive new measure utilizes all the available classification information and serves as a cut-points selection criterion as well. Both the geometric and probabilistic interpretations for the new measure are examined. Power and simulation studies are carried out to investigate its performance as a measure of diagnostic accuracy as well as cut-points selection criterion. A real data set from Alzheimer's Disease Neuroimaging Initiative is analyzed using the proposed maximum absolute determinant.

  13. Wavelength selection in injection-driven Hele-Shaw flows: A maximum amplitude criterion

    Science.gov (United States)

    Dias, Eduardo; Miranda, Jose

    2013-11-01

    As in most interfacial flow problems, the standard theoretical procedure to establish wavelength selection in the viscous fingering instability is to maximize the linear growth rate. However, there are important discrepancies between previous theoretical predictions and existing experimental data. In this work we perform a linear stability analysis of the radial Hele-Shaw flow system that takes into account the combined action of viscous normal stresses and wetting effects. Most importantly, we introduce an alternative selection criterion for which the selected wavelength is determined by the maximum of the interfacial perturbation amplitude. The effectiveness of such a criterion is substantiated by the significantly improved agreement between theory and experiments. We thank CNPq (Brazilian Sponsor) for financial support.

  14. A graphical criterion for working fluid selection and thermodynamic system comparison in waste heat recovery

    International Nuclear Information System (INIS)

    Xi, Huan; Li, Ming-Jia; He, Ya-Ling; Tao, Wen-Quan

    2015-01-01

    In the present study, we proposed a graphical criterion called CE diagram by achieving the Pareto optimal solutions of the annual cash flow and exergy efficiency. This new graphical criterion enables both working fluid selection and thermodynamic system comparison for waste heat recovery. It's better than the existing criterion based on single objective optimization because it is graphical and intuitionistic in the form of diagram. The features of CE diagram were illustrated by studying 5 examples with different heat-source temperatures (ranging between 100 °C to 260 °C), 26 chlorine-free working fluids and two typical ORC systems including basic organic Rankine cycle(BORC) and recuperative organic Rankine cycle (RORC). It is found that the proposed graphical criterion is feasible and can be applied to any closed loop waste heat recovery thermodynamic systems and working fluids. - Highlights: • A graphical method for ORC system comparison/working fluid selection was proposed. • Multi-objectives genetic algorithm (MOGA) was applied for optimizing ORC systems. • Application cases were performed to demonstrate the usage of the proposed method.

  15. Fatigue crack growth threshold as a design criterion - statistical scatter and load ratio in the Kitagawa-Takahashi diagram

    International Nuclear Information System (INIS)

    Kolitsch, S.; Gänser, H.-P.; Maierhofer, J.; Pippan, R.

    2016-01-01

    Cracks in components reduce the endurable stress so that the endurance limit obtained from common smooth fatigue specimens cannot be used anymore as a design criterion. In such cases, the Kitagawa-Takahashi diagram can be used to predict the admissible stress range for infinite life, at a given crack length and stress range. This diagram is constructed for a single load ratio R. However, in typical mechanical engineering applications, the load ratio R varies widely due to the applied load spectra and residual stresses. In the present work an extended Kitagawa-Takahashi diagram accounting for crack length, crack extension and load ratio is constructed. To describe the threshold behaviour of short cracks, a master resistance curve valid for a wide range of steels is developed using a statistical approach. (paper)

  16. Determine the optimal carrier selection for a logistics network based on multi-commodity reliability criterion

    Science.gov (United States)

    Lin, Yi-Kuei; Yeh, Cheng-Ta

    2013-05-01

    From the perspective of supply chain management, the selected carrier plays an important role in freight delivery. This article proposes a new criterion of multi-commodity reliability and optimises the carrier selection based on such a criterion for logistics networks with routes and nodes, over which multiple commodities are delivered. Carrier selection concerns the selection of exactly one carrier to deliver freight on each route. The capacity of each carrier has several available values associated with a probability distribution, since some of a carrier's capacity may be reserved for various orders. Therefore, the logistics network, given any carrier selection, is a multi-commodity multi-state logistics network. Multi-commodity reliability is defined as a probability that the logistics network can satisfy a customer's demand for various commodities, and is a performance indicator for freight delivery. To solve this problem, this study proposes an optimisation algorithm that integrates genetic algorithm, minimal paths and Recursive Sum of Disjoint Products. A practical example in which multi-sized LCD monitors are delivered from China to Germany is considered to illustrate the solution procedure.

  17. Genetic Gain Increases by Applying the Usefulness Criterion with Improved Variance Prediction in Selection of Crosses.

    Science.gov (United States)

    Lehermeier, Christina; Teyssèdre, Simon; Schön, Chris-Carolin

    2017-12-01

    A crucial step in plant breeding is the selection and combination of parents to form new crosses. Genome-based prediction guides the selection of high-performing parental lines in many crop breeding programs which ensures a high mean performance of progeny. To warrant maximum selection progress, a new cross should also provide a large progeny variance. The usefulness concept as measure of the gain that can be obtained from a specific cross accounts for variation in progeny variance. Here, it is shown that genetic gain can be considerably increased when crosses are selected based on their genomic usefulness criterion compared to selection based on mean genomic estimated breeding values. An efficient and improved method to predict the genetic variance of a cross based on Markov chain Monte Carlo samples of marker effects from a whole-genome regression model is suggested. In simulations representing selection procedures in crop breeding programs, the performance of this novel approach is compared with existing methods, like selection based on mean genomic estimated breeding values and optimal haploid values. In all cases, higher genetic gain was obtained compared with previously suggested methods. When 1% of progenies per cross were selected, the genetic gain based on the estimated usefulness criterion increased by 0.14 genetic standard deviation compared to a selection based on mean genomic estimated breeding values. Analytical derivations of the progeny genotypic variance-covariance matrix based on parental genotypes and genetic map information make simulations of progeny dispensable, and allow fast implementation in large-scale breeding programs. Copyright © 2017 by the Genetics Society of America.

  18. Directional Histogram Ratio at Random Probes: A Local Thresholding Criterion for Capillary Images

    Science.gov (United States)

    Lu, Na; Silva, Jharon; Gu, Yu; Gerber, Scott; Wu, Hulin; Gelbard, Harris; Dewhurst, Stephen; Miao, Hongyu

    2013-01-01

    With the development of micron-scale imaging techniques, capillaries can be conveniently visualized using methods such as two-photon and whole mount microscopy. However, the presence of background staining, leaky vessels and the diffusion of small fluorescent molecules can lead to significant complexity in image analysis and loss of information necessary to accurately quantify vascular metrics. One solution to this problem is the development of accurate thresholding algorithms that reliably distinguish blood vessels from surrounding tissue. Although various thresholding algorithms have been proposed, our results suggest that without appropriate pre- or post-processing, the existing approaches may fail to obtain satisfactory results for capillary images that include areas of contamination. In this study, we propose a novel local thresholding algorithm, called directional histogram ratio at random probes (DHR-RP). This method explicitly considers the geometric features of tube-like objects in conducting image binarization, and has a reliable performance in distinguishing small vessels from either clean or contaminated background. Experimental and simulation studies suggest that our DHR-RP algorithm is superior over existing thresholding methods. PMID:23525856

  19. Omega-optimized portfolios: applying stochastic dominance criterion for the selection of the threshold return

    Directory of Open Access Journals (Sweden)

    Renaldas Vilkancas

    2016-05-01

    Full Text Available Purpose of the article: While using asymmetric risk-return measures an important role is played by selection of the investor‘s required or threshold rate of return. The scientific literature usually states that every investor should define this rate according to their degree of risk aversion. In this paper, it is attempted to look at the problem from a different perspective – empirical research is aimed at determining the influence of the threshold rate of return on the portfolio characteristics. Methodology/methods: In order to determine the threshold rate of return a stochastic dominance criterion was used. The results are verified using the commonly applied method of backtesting. Scientific aim: The aim of this paper is to propose a method allowing selecting the threshold rate of return reliably and objectively. Findings: Empirical research confirms that stochastic dominance criteria can be successfully applied to determine the rate of return preferred by the investor. Conclusions: A risk-free investment rate or simply a zero rate of return commonly used in practice is often justified neither by theoretical nor empirical studies. This work suggests determining the threshold rate of return by applying the stochastic dominance criterion

  20. Fruit Phenolic Profiling: A New Selection Criterion in Olive Breeding Programs.

    Science.gov (United States)

    Pérez, Ana G; León, Lorenzo; Sanz, Carlos; de la Rosa, Raúl

    2018-01-01

    Olive growing is mainly based on traditional varieties selected by the growers across the centuries. The few attempts so far reported to obtain new varieties by systematic breeding have been mainly focused on improving the olive adaptation to different growing systems, the productivity and the oil content. However, the improvement of oil quality has rarely been considered as selection criterion and only in the latter stages of the breeding programs. Due to their health promoting and organoleptic properties, phenolic compounds are one of the most important quality markers for Virgin olive oil (VOO) although they are not commonly used as quality traits in olive breeding programs. This is mainly due to the difficulties for evaluating oil phenolic composition in large number of samples and the limited knowledge on the genetic and environmental factors that may influence phenolic composition. In the present work, we propose a high throughput methodology to include the phenolic composition as a selection criterion in olive breeding programs. For that purpose, the phenolic profile has been determined in fruits and oils of several breeding selections and two varieties ("Picual" and "Arbequina") used as control. The effect of three different environments, typical for olive growing in Andalusia, Southern Spain, was also evaluated. A high genetic effect was observed on both fruit and oil phenolic profile. In particular, the breeding selection UCI2-68 showed an optimum phenolic profile, which sums up to a good agronomic performance previously reported. A high correlation was found between fruit and oil total phenolic content as well as some individual phenols from the two different matrices. The environmental effect on phenolic compounds was also significant in both fruit and oil, although the low genotype × environment interaction allowed similar ranking of genotypes on the different environments. In summary, the high genotypic variance and the simplified procedure of the

  1. Value of prostate specific antigen and prostatic volume ratio (PSA/V) as the selection criterion for US-guided prostatic biopsy. Importanza del rapporto tra antigene prostatico specifico e volume prostatico nella selezione dei pazienti da sottoporre a biopsia ecoguidata della prostata

    Energy Technology Data Exchange (ETDEWEB)

    Veneziano, S; Paulica, P; Querze' , R; Viglietta, G; Trenta, A [Ospedale Melpighi, Bologna (Italy). Serv. di Radiologia

    1991-01-01

    US-guided biopsy was performed in 94 patients with suspected lesions at transerectal US. Histology demonstrated carcinoma in 43 cases, benign hyperplasia in 44, and prostatis in 7. In all cases the prostate specific antigen (PSA) was calculated, by means of US, together with prostatic volume (v). PSA was related to the corresponding gland volume, which resulted in PSA/V ratio. Our study showed PSA/V ration to have higher sensitivity and specificity than absolulute PSA value in the diagnosis of prostatic carcinoma. The authors believe prostate US-guided biopsy to be: a) necessary when the suspected area has PSA/V ratio >0.15, and especially when PSA/V >0.30; b) not indicated when echo-structural alterations are associated with PSA/V <0.15, because they are most frequently due to benign lesions. The combined use of PSA/V ratio and US is therefore suggested to select the patients in whom biopsy is to be performed. 20 refs.

  2. Sex Ratio Elasticity Influences the Selection of Sex Ratio Strategy

    Science.gov (United States)

    Wang, Yaqiang; Wang, Ruiwu; Li, Yaotang; (Sam) Ma, Zhanshan

    2016-12-01

    There are three sex ratio strategies (SRS) in nature—male-biased sex ratio, female-biased sex ratio and, equal sex ratio. It was R. A. Fisher who first explained why most species in nature display a sex ratio of ½. Consequent SRS theories such as Hamilton’s local mate competition (LMC) and Clark’s local resource competition (LRC) separately explained the observed deviations from the seemingly universal 1:1 ratio. However, to the best of our knowledge, there is not yet a unified theory that accounts for the mechanisms of the three SRS. Here, we introduce the price elasticity theory in economics to define sex ratio elasticity (SRE), and present an analytical model that derives three SRSs based on the following assumption: simultaneously existing competitions for both resources A and resources B influence the level of SRE in both sexes differently. Consequently, it is the difference (between two sexes) in the level of their sex ratio elasticity that leads to three different SRS. Our analytical results demonstrate that the elasticity-based model not only reveals a highly plausible mechanism that explains the evolution of SRS in nature, but also offers a novel framework for unifying two major classical theories (i.e., LMC & LRC) in the field of SRS research.

  3. Using the Predictability Criterion for Selecting Extended Verbs for Shona Dictionaries

    Directory of Open Access Journals (Sweden)

    Emmanuel Chabata

    2012-09-01

    Full Text Available

    The paper examines the "predictability criterion", a classificatory tool which is used in selecting affixed word forms for dictionary entries. It focuses on the criterion as it has been used by the African Languages Lexical (ALLEX Project for selecting extended verbs to enter as headwords in the Project's first monolingual Shona dictionary Duramazwi ReChiShona. The article also examines the status of Shona verbal extensions in terms of their semantic input to the verb stems they are attached to. The paper was originally motivated by two observations: (a that predictability seems to be a matter of degree; and (b that the predictability criterion tended to be used inconsistently in the selection of extended verbs and senses for Duramazwi ReChiShona. An analysis of 412 productively extended verbs that were entered as headwords in Duramazwi ReChiShona shows that verbal extensions can bring both predictable and unpredictable senses to the verb stems they are attached to. The paper demonstrates that for an effective use of the predictability criterion for selecting extended verbs for Shona dictionaries, there is need for the lexicographer to have an in-depth understanding of the kinds of semantic movements that are caused when verb stems are extended. It shows the need to view verbal extensions in Shona as derivational morphemes, not inflectional morphemes as some earlier scholars have concluded.

     

     

    Die gebruik van die voorspelbaarheidskriterium om uitgebreide werkwoorde te selekteer vir Shonawoordeboeke

    Hierdie artikel ondersoek die "voorspelbaarheidskriterium", 'n klassifikasiehulpmiddel wat gebruik word om geaffigeerde woordvorme te selekteer as woordeboekinskrywings. Dit fokus op die kriterium soos dit gebruik is deur die African Language Lexical (ALLEX Project vir die selektering van uitgebreide werkwoorde as lemmas in die Projek se eerste eentalige Shonawoordeboek Duramazwi ReChiShona. In

  4. A Novel Non-Invasive Selection Criterion for the Preservation of Primitive Dutch Konik Horses.

    Science.gov (United States)

    May-Davis, Sharon; Brown, Wendy Y; Shorter, Kathleen; Vermeulen, Zefanja; Butler, Raquel; Koekkoek, Marianne

    2018-02-01

    The Dutch Konik is valued from a genetic conservation perspective and also for its role in preservation of natural landscapes. The primary management objective for the captive breeding of this primitive horse is to maintain its genetic purity, whilst also maintaining the nature reserves on which they graze. Breeding selection has traditionally been based on phenotypic characteristics consistent with the breed description, and the selection of animals for removal from the breeding program is problematic at times due to high uniformity within the breed, particularly in height at the wither, colour (mouse to grey dun) and presence of primitive markings. With the objective of identifying an additional non-invasive selection criterion with potential uniqueness to the Dutch Konik, this study investigates the anatomic parameters of the distal equine limb, with a specific focus on the relative lengths of the individual splint bones. Post-mortem dissections performed on distal limbs of Dutch Konik ( n = 47) and modern domesticated horses ( n = 120) revealed significant differences in relation to the length and symmetry of the 2nd and 4th Metacarpals and Metatarsals. Distal limb characteristics with apparent uniqueness to the Dutch Konik are described which could be an important tool in the selection and preservation of the breed.

  5. Fruit Phenolic Profiling: A New Selection Criterion in Olive Breeding Programs

    Directory of Open Access Journals (Sweden)

    Ana G. Pérez

    2018-02-01

    Full Text Available Olive growing is mainly based on traditional varieties selected by the growers across the centuries. The few attempts so far reported to obtain new varieties by systematic breeding have been mainly focused on improving the olive adaptation to different growing systems, the productivity and the oil content. However, the improvement of oil quality has rarely been considered as selection criterion and only in the latter stages of the breeding programs. Due to their health promoting and organoleptic properties, phenolic compounds are one of the most important quality markers for Virgin olive oil (VOO although they are not commonly used as quality traits in olive breeding programs. This is mainly due to the difficulties for evaluating oil phenolic composition in large number of samples and the limited knowledge on the genetic and environmental factors that may influence phenolic composition. In the present work, we propose a high throughput methodology to include the phenolic composition as a selection criterion in olive breeding programs. For that purpose, the phenolic profile has been determined in fruits and oils of several breeding selections and two varieties (“Picual” and “Arbequina” used as control. The effect of three different environments, typical for olive growing in Andalusia, Southern Spain, was also evaluated. A high genetic effect was observed on both fruit and oil phenolic profile. In particular, the breeding selection UCI2-68 showed an optimum phenolic profile, which sums up to a good agronomic performance previously reported. A high correlation was found between fruit and oil total phenolic content as well as some individual phenols from the two different matrices. The environmental effect on phenolic compounds was also significant in both fruit and oil, although the low genotype × environment interaction allowed similar ranking of genotypes on the different environments. In summary, the high genotypic variance and the

  6. Characteristics of Criterion-Referenced Instruments: Implications for Materials Selection for the Learning Disabled.

    Science.gov (United States)

    Blasi, Joyce F.

    Discussed are characteristics of criterion referenced reading tests for use with learning disabled (LD) children, and analyzed are the Basic Educational Skills Inventory (BESI), the Prescriptive Reading Inventory (PRI), and the Cooper-McGuire Diagnostic Work-Analysis Test (CooperMcGuire). Criterion referenced tests are defined; and problems in…

  7. Variation and design criterion of heat load ratio of generator for air cooled lithium bromide–water double effect absorption chiller

    International Nuclear Information System (INIS)

    Li, Zeyu; Liu, Liming; Liu, Jinping

    2016-01-01

    Highlights: • Design criterion of heat load ratio of generator is vital to system performance. • Heat load ratio of generator changes with working condition. • Change of heat load ratio of generator for four systems was obtained and compared. • Design criterion of heat load ratio of generator was presented. - Abstract: The heat load ratio of generator (HLRG) is a special system parameter because it is not fixed at the design value but changes with the working condition. For the air cooled chiller, the deviation from the design working condition occurs easily due to the variation of the surrounding temperature. The system is likely to suffer from crystallization when the working condition is different from the designed one if the HLRG is designed improperly. Consequently, the design criterion of HLRG based on a broad range of working condition is essential and urgent to the development of air cooled lithium bromide–water double effect absorption chiller. This paper mainly deals with the variation of HLRG with the working condition as well as corresponding design criterion. Four types of double effect chillers named series, pre-parallel, rear parallel and reverse parallel flow system were considered. The parametric model was developed by the introduction of a new thermodynamic relationship of generator. The change of HLRG for different types of chillers with the working condition was analyzed and compared. The corresponding design criterion of HLRG was presented. This paper is helpful for further improvement of the performance and reliability of air cooled lithium bromide–water double effect absorption chiller.

  8. Drinking Water Quality Criterion - Based site Selection of Aquifer Storage and Recovery Scheme in Chou-Shui River Alluvial Fan

    Science.gov (United States)

    Huang, H. E.; Liang, C. P.; Jang, C. S.; Chen, J. S.

    2015-12-01

    Land subsidence due to groundwater exploitation is an urgent environmental problem in Choushui river alluvial fan in Taiwan. Aquifer storage and recovery (ASR), where excess surface water is injected into subsurface aquifers for later recovery, is one promising strategy for managing surplus water and may overcome water shortages. The performance of an ASR scheme is generally evaluated in terms of recovery efficiency, which is defined as percentage of water injected in to a system in an ASR site that fulfills the targeted water quality criterion. Site selection of an ASR scheme typically faces great challenges, due to the spatial variability of groundwater quality and hydrogeological condition. This study proposes a novel method for the ASR site selection based on drinking quality criterion. Simplified groundwater flow and contaminant transport model spatial distributions of the recovery efficiency with the help of the groundwater quality, hydrological condition, ASR operation. The results of this study may provide government administrator for establishing reliable ASR scheme.

  9. Does the Lowest Bid Price Evaluation Criterion Make for a More Efficient Public Procurement Selection Criterion? (Case of the Czech Republic

    Directory of Open Access Journals (Sweden)

    Ochrana František

    2015-06-01

    Full Text Available Through the institute of public procurement a considerable volume of financial resources is allocated. It is therefore in the interest of contracting entities to seek ways of how to achieve an efficient allocation of resources. Some public contract-awarding entities, along with some public-administration authorities in the Czech Republic, believe that the use of a single evaluation criterion (the lowest bid price results in a more efficient tender for a public contract. It was found that contracting entities in the Czech Republic strongly prefer to use the lowest bid price criterion. Within the examined sample, 86.5 % of public procurements were evaluated this way. The analysis of the examined sample of public contracts proved that the choice of an evaluation criterion, even the preference of the lowest bid price criterion, does not have any obvious impact on the final cost of a public contract. The study concludes that it is inappropriate to prefer the criterion of the lowest bid price within the evaluation of public contracts that are characterised by their complexity (including public contracts for construction works and public service contracts. The findings of the Supreme Audit Office related to the inspection of public contracts indicate that when using the lowest bid price as an evaluation criterion, a public contract may indeed be tendered with the lowest bid price, but not necessarily the best offer in terms of supplied quality. It is therefore not appropriate to use the lowest bid price evaluation criterion to such an extent for the purpose of evaluating work and services. Any improvement to this situation requires a corresponding amendment to the Law on Public Contracts and mainly a radical change in the attitude of the Office for the Protection of Competition towards proposed changes, as indicated within the conclusions and recommendations proposed by this study.

  10. Failure criterion effect on solid production prediction and selection of completion solution

    Directory of Open Access Journals (Sweden)

    Dariush Javani

    2017-12-01

    Full Text Available Production of fines together with reservoir fluid is called solid production. It varies from a few grams or less per ton of reservoir fluid posing only minor problems, to catastrophic amount possibly leading to erosion and complete filling of the borehole. This paper assesses solid production potential in a carbonate gas reservoir located in the south of Iran. Petrophysical logs obtained from the vertical well were employed to construct mechanical earth model. Then, two failure criteria, i.e. Mohr–Coulomb and Mogi–Coulomb, were used to investigate the potential of solid production of the well in the initial and depleted conditions of the reservoir. Using these two criteria, we estimated critical collapse pressure and compared them to the reservoir pressure. Solid production occurs if collapse pressure is greater than pore pressure. Results indicate that the two failure criteria show different estimations of solid production potential of the studied reservoir. Mohr–Coulomb failure criterion estimated solid production in both initial and depleted conditions, where Mogi–Coulomb criterion predicted no solid production in the initial condition of reservoir. Based on Mogi–Coulomb criterion, the well may not require completion solutions like perforated liner, until at least 60% of reservoir pressure was depleted which leads to decrease in operation cost and time.

  11. Financial performance as a decision criterion of credit scoring models selection [doi: 10.21529/RECADM.2017004

    Directory of Open Access Journals (Sweden)

    Rodrigo Alves Silva

    2017-09-01

    Full Text Available This paper aims to show the importance of the use of financial metrics in decision-making of credit scoring models selection. In order to achieve such, we considered an automatic approval system approach and we carried out a performance analysis of the financial metrics on the theoretical portfolios generated by seven credit scoring models based on main statistical learning techniques. The models were estimated on German Credit dataset and the results were analyzed based on four metrics: total accuracy, error cost, risk adjusted return on capital and Sharpe index. The results show that total accuracy, widely used as a criterion for selecting credit scoring models, is unable to select the most profitable model for the company, indicating the need to incorporate financial metrics into the credit scoring model selection process. Keywords Credit risk; Model’s selection; Statistical learning.

  12. Evaluation of feed COD/sulfate ratio as a control criterion for the biological hydrogen sulfide production and lead precipitation

    International Nuclear Information System (INIS)

    Velasco, Antonio; Ramirez, Martha; Volke-Sepulveda, Tania; Gonzalez-Sanchez, Armando; Revah, Sergio

    2008-01-01

    The ability of sulfate-reducing bacteria to produce hydrogen sulfide and the high affinity of sulfide to react with divalent metallic cations represent an excellent option to remove heavy metals from wastewater. Different parameters have been proposed to control the hydrogen sulfide production by anaerobic bacteria, such as the organic and sulfate loading rates and the feed COD/SO 4 2- ratio. This work relates the feed COD/SO 4 2- ratio with the hydrogen sulfide production and dissolved lead precipitation, using ethanol as carbon and energy source in an up-flow anaerobic sludge blanket reactor. A maximum dissolved sulfide concentration of 470 ± 7 mg S/L was obtained at a feed COD/SO 4 2- ratio of 2.5, with sulfate and ethanol conversions of approximately 94 and 87%, respectively. The lowest dissolved sulfide concentration (145 ± 10 mg S/L) was observed with a feed COD/SO 4 2- ratio of 0.67. Substantial amounts of acetate (510-1730 mg/L) were produced and accumulated in the bioreactor from ethanol oxidation. Although only incomplete oxidation of ethanol to acetate was observed, the consortium was able to remove 99% of the dissolved lead (200 mg/L) with a feed COD/SO 4 2- ratio of 1.5. It was found that the feed COD/SO 4 2- ratio could be an adequate parameter to control the hydrogen sulfide production and the consequent precipitation of dissolved lead

  13. Continuous-Time Portfolio Selection and Option Pricing under Risk-Minimization Criterion in an Incomplete Market

    Directory of Open Access Journals (Sweden)

    Xinfeng Ruan

    2013-01-01

    Full Text Available We study option pricing with risk-minimization criterion in an incomplete market where the dynamics of the risky underlying asset are governed by a jump diffusion equation. We obtain the Radon-Nikodym derivative in the minimal martingale measure and a partial integrodifferential equation (PIDE of European call option. In a special case, we get the exact solution for European call option by Fourier transformation methods. Finally, we employ the pricing kernel to calculate the optimal portfolio selection by martingale methods.

  14. Evaluation of feed COD/sulfate ratio as a control criterion for the biological hydrogen sulfide production and lead precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Velasco, Antonio [Direccion General del Centro Nacional de Investigacion y Capacitacion Ambiental-Instituto Nacional de Ecologia, Av. San Rafael Atlixco 186, Col. Vicentina. Iztapalapa, Mexico 09340, D.F. (Mexico)], E-mail: jvelasco@ine.gob.mx; Ramirez, Martha [Direccion General del Centro Nacional de Investigacion y Capacitacion Ambiental-Instituto Nacional de Ecologia, Av. San Rafael Atlixco 186, Col. Vicentina. Iztapalapa, Mexico 09340, D.F. (Mexico); Volke-Sepulveda, Tania [Departamento de Biotecnologia, UAM-Cuajimalpa, San Rafael Atlixco 186, Col. Vicentina. Iztapalapa, Mexico 09340, D.F. (Mexico); Gonzalez-Sanchez, Armando [Departamento de Ingenieria de Procesos, Universidad Autonoma Metropolitana-Iztapalapa, UAM-Cuajimalpa, San Rafael Atlixco 186, Col. Vicentina. Iztapalapa, Mexico 09340, D.F. (Mexico); Revah, Sergio [Departamento de Procesos y Tecnologia, UAM-Cuajimalpa, San Rafael Atlixco 186, Col. Vicentina. Iztapalapa, Mexico 09340, D.F. (Mexico)

    2008-03-01

    The ability of sulfate-reducing bacteria to produce hydrogen sulfide and the high affinity of sulfide to react with divalent metallic cations represent an excellent option to remove heavy metals from wastewater. Different parameters have been proposed to control the hydrogen sulfide production by anaerobic bacteria, such as the organic and sulfate loading rates and the feed COD/SO{sub 4}{sup 2-} ratio. This work relates the feed COD/SO{sub 4}{sup 2-} ratio with the hydrogen sulfide production and dissolved lead precipitation, using ethanol as carbon and energy source in an up-flow anaerobic sludge blanket reactor. A maximum dissolved sulfide concentration of 470 {+-} 7 mg S/L was obtained at a feed COD/SO{sub 4}{sup 2-} ratio of 2.5, with sulfate and ethanol conversions of approximately 94 and 87%, respectively. The lowest dissolved sulfide concentration (145 {+-} 10 mg S/L) was observed with a feed COD/SO{sub 4}{sup 2-} ratio of 0.67. Substantial amounts of acetate (510-1730 mg/L) were produced and accumulated in the bioreactor from ethanol oxidation. Although only incomplete oxidation of ethanol to acetate was observed, the consortium was able to remove 99% of the dissolved lead (200 mg/L) with a feed COD/SO{sub 4}{sup 2-} ratio of 1.5. It was found that the feed COD/SO{sub 4}{sup 2-} ratio could be an adequate parameter to control the hydrogen sulfide production and the consequent precipitation of dissolved lead.

  15. [Employees in high-reliability organizations: systematic selection of personnel as a final criterion].

    Science.gov (United States)

    Oubaid, V; Anheuser, P

    2014-05-01

    Employees represent an important safety factor in high-reliability organizations. The combination of clear organizational structures, a nonpunitive safety culture, and psychological personnel selection guarantee a high level of safety. The cockpit personnel selection process of a major German airline is presented in order to demonstrate a possible transferability into medicine and urology.

  16. Key Determinant Derivations for Information Technology Disaster Recovery Site Selection by the Multi-Criterion Decision Making Method

    Directory of Open Access Journals (Sweden)

    Chia-Lee Yang

    2015-05-01

    Full Text Available Disaster recovery sites are an important mechanism in continuous IT system operations. Such mechanisms can sustain IT availability and reduce business losses during natural or human-made disasters. Concerning the cost and risk aspects, the IT disaster-recovery site selection problems are multi-criterion decision making (MCDM problems in nature. For such problems, the decision aspects include the availability of the service, recovery time requirements, service performance, and more. The importance and complexities of IT disaster recovery sites increases with advances in IT and the categories of possible disasters. The modern IT disaster recovery site selection process requires further investigation. However, very few researchers tried to study related issues during past years based on the authors’ extremely limited knowledge. Thus, this paper aims to derive the aspects and criteria for evaluating and selecting a modern IT disaster recovery site. A hybrid MCDM framework consisting of the Decision Making Trial and Evaluation Laboratory (DEMATEL and the Analytic Network Process (ANP will be proposed to construct the complex influence relations between aspects as well as criteria and further, derive weight associated with each aspect and criteria. The criteria with higher weight can be used for evaluating and selecting the most suitable IT disaster recovery sites. In the future, the proposed analytic framework can be used for evaluating and selecting a disaster recovery site for data centers by public institutes or private firms.

  17. Advance Pricing Agreements and the Selectivity Criterion in EU State Aid Rules

    OpenAIRE

    Härö, O

    2017-01-01

    The Commission of the EU has recently decided that Advance Pricing Agreement rulings (the APA rulings) that Ireland, Luxembourg and the Netherlands have granted for Apple, Fiat and Starbucks (respectively) constitute illegal State aid according to Article 107 of the Treaty on the Functioning of the European Union (TFEU). The Commission claims that the APA rulings deviate from the arm´s length principle and that they grant economic benefit for the beneficiary undertakings in a selective manner...

  18. Heuristics and Criterion Setting during Selective Encoding in Visual Decision-Making: Evidence from Eye Movements.

    Science.gov (United States)

    Schotter, Elizabeth R; Gerety, Cainen; Rayner, Keith

    2012-01-01

    When making a decision, people spend longer looking at the option they ultimately choose compared other options-termed the gaze bias effect-even during their first encounter with the options (Glaholt & Reingold, 2009a, 2009b; Schotter, Berry, McKenzie & Rayner, 2010). Schotter et al. (2010) suggested that this is because people selectively encode decision-relevant information about the options, on-line during the first encounter with them. To extend their findings and test this claim, we recorded subjects' eye movements as they made judgments about pairs of images (i.e., which one was taken more recently or which one was taken longer ago). We manipulated whether both images were presented in the same color content (e.g., both in color or both in black-and-white) or whether they differed in color content and the extent to which color content was a reliable cue to relative recentness of the images. We found that the magnitude of the gaze bias effect decreased when the color content cue was not reliable during the first encounter with the images, but no modulation of the gaze bias effect in remaining time on the trial. These data suggest people do selectively encode decision-relevant information on-line.

  19. Growth kinetic and fuel quality parameters as selective criterion for screening biodiesel producing cyanobacterial strains.

    Science.gov (United States)

    Gayathri, Manickam; Shunmugam, Sumathy; Mugasundari, Arumugam Vanmathi; Rahman, Pattanathu K S M; Muralitharan, Gangatharan

    2018-01-01

    The efficiency of cyanobacterial strains as biodiesel feedstock varies with the dwelling habitat. Fourteen indigenous heterocystous cyanobacterial strains from rice field ecosystem were screened based on growth kinetic and fuel parameters. The highest biomass productivity was obtained in Nostoc punctiforme MBDU 621 (19.22mg/L/day) followed by Calothrix sp. MBDU 701 (13.43mg/L/day). While lipid productivity and lipid content was highest in Nostoc spongiaeforme MBDU 704 (4.45mg/L/day and 22.5%dwt) followed by Calothrix sp. MBDU 701 (1.54mg/L/day and 10.75%dwt). Among the tested strains, Nostoc spongiaeforme MBDU 704 and Nostoc punctiforme MBDU 621 were selected as promising strains for good quality biodiesel production by Preference Ranking Organization Method for Enrichment Evaluation (PROMETHEE) and Graphical Analysis for Interactive Assistance (GAIA) analysis. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. An integrative analysis of reprogramming in human isogenic system identified a clone selection criterion.

    Science.gov (United States)

    Shutova, Maria V; Surdina, Anastasia V; Ischenko, Dmitry S; Naumov, Vladimir A; Bogomazova, Alexandra N; Vassina, Ekaterina M; Alekseev, Dmitry G; Lagarkova, Maria A; Kiselev, Sergey L

    2016-01-01

    The pluripotency of newly developed human induced pluripotent stem cells (iPSCs) is usually characterized by physiological parameters; i.e., by their ability to maintain the undifferentiated state and to differentiate into derivatives of the 3 germ layers. Nevertheless, a molecular comparison of physiologically normal iPSCs to the "gold standard" of pluripotency, embryonic stem cells (ESCs), often reveals a set of genes with different expression and/or methylation patterns in iPSCs and ESCs. To evaluate the contribution of the reprogramming process, parental cell type, and fortuity in the signature of human iPSCs, we developed a complete isogenic reprogramming system. We performed a genome-wide comparison of the transcriptome and the methylome of human isogenic ESCs, 3 types of ESC-derived somatic cells (fibroblasts, retinal pigment epithelium and neural cells), and 3 pairs of iPSC lines derived from these somatic cells. Our analysis revealed a high input of stochasticity in the iPSC signature that does not retain specific traces of the parental cell type and reprogramming process. We showed that 5 iPSC clones are sufficient to find with 95% confidence at least one iPSC clone indistinguishable from their hypothetical isogenic ESC line. Additionally, on the basis of a small set of genes that are characteristic of all iPSC lines and isogenic ESCs, we formulated an approach of "the best iPSC line" selection and confirmed it on an independent dataset.

  1. Bacterial selection for biological control of plant disease: criterion determination and validation

    Directory of Open Access Journals (Sweden)

    Monalize Salete Mota

    Full Text Available Abstract This study aimed to evaluate the biocontrol potential of bacteria isolated from different plant species and soils. The production of compounds related to phytopathogen biocontrol and/or promotion of plant growth in bacterial isolates was evaluated by measuring the production of antimicrobial compounds (ammonia and antibiosis and hydrolytic enzymes (amylases, lipases, proteases, and chitinases and phosphate solubilization. Of the 1219 bacterial isolates, 92% produced one or more of the eight compounds evaluated, but only 1% of the isolates produced all the compounds. Proteolytic activity was most frequently observed among the bacterial isolates. Among the compounds which often determine the success of biocontrol, 43% produced compounds which inhibit mycelial growth of Monilinia fructicola, but only 11% hydrolyzed chitin. Bacteria from different plant species (rhizosphere or phylloplane exhibited differences in the ability to produce the compounds evaluated. Most bacterial isolates with biocontrol potential were isolated from rhizospheric soil. The most efficient bacteria (producing at least five compounds related to phytopathogen biocontrol and/or plant growth, 86 in total, were evaluated for their biocontrol potential by observing their ability to kill juvenile Mesocriconema xenoplax. Thus, we clearly observed that bacteria that produced more compounds related to phytopathogen biocontrol and/or plant growth had a higher efficacy for nematode biocontrol, which validated the selection strategy used.

  2. Selective breeding for a behavioral trait changes digit ratio.

    Directory of Open Access Journals (Sweden)

    Reginia H Y Yan

    Full Text Available The ratio of the length of the second digit (index finger divided by the fourth digit (ring finger tends to be lower in men than in women. This 2D:4D digit ratio is often used as a proxy for prenatal androgen exposure in studies of human health and behavior. For example, 2D:4D ratio is lower (i.e. more "masculinized" in both men and women of greater physical fitness and/or sporting ability. Lab mice have also shown variation in 2D:4D as a function of uterine environment, and mouse digit ratios seem also to correlate with behavioral traits, including daily activity levels. Selective breeding for increased rates of voluntary exercise (wheel running in four lines of mice has caused correlated increases in aerobic exercise capacity, circulating corticosterone level, and predatory aggression. Here, we show that this selection regime has also increased 2D:4D. This apparent "feminization" in mice is opposite to the relationship seen between 2D:4D and physical fitness in human beings. The present results are difficult to reconcile with the notion that 2D:4D is an effective proxy for prenatal androgen exposure; instead, it may more accurately reflect effects of glucocorticoids, or other factors that regulate any of many genes.

  3. Criterion for the selection of a system of treatment of residues and their application to the wine of the alcoholic industry

    International Nuclear Information System (INIS)

    Caicedo M, Luis Alfonso; Fonseca, Jose Joaquin; Rodriguez, Gerardo

    1996-01-01

    The selection of a system of residues treatment should follow the criterion of the process denominated BATEA (better available and feasible technical and economical process). Because their application is difficult for not having objective parameters of evaluation, a method is presented that classifies the evaluation criterions in general and specific. For the quantification of these aspects factors like FQO are used, FCI, FTR, FD and the factor of applicability of the treatment (FAT). The method applied to the wine; allows concluding that it is the evaporation the best treatment system for this process, while other systems are not developed or it increases the recompensing rate

  4. Optimized thick-wall cylinders by virtue of Poisson's ratio selection

    International Nuclear Information System (INIS)

    Whitty, J.P.M.; Henderson, B.; Francis, J.; Lloyd, N.

    2011-01-01

    The principal stress distributions in thick-wall cylinders due to variation in the Poisson's ratio are predicted using analytical and finite element methods. Analyses of appropriate brittle and ductile failure criteria show that under the isochoric pressure conditions investigated that auextic (i.e. those possessing a negative Poisson's ratio) materials act as stress concentrators; hence they are predicted to fail before their conventional (i.e. possessing a positive Poisson's ratio) material counterparts. The key finding of the work presented shows that for constrained thick-wall cylinders the maximum tensile principal stress can vanish at a particular Poisson's ratio and aspect ratio. This phenomenon is exploited in order to present an optimized design criterion for thick-wall cylinders. Moreover, via the use of a cogent finite element model, this criterion is also shown to be applicable for the design of micro-porous materials.

  5. Electronic Devices, Methods, and Computer Program Products for Selecting an Antenna Element Based on a Wireless Communication Performance Criterion

    DEFF Research Database (Denmark)

    2014-01-01

    A method of operating an electronic device includes providing a plurality of antenna elements, evaluating a wireless communication performance criterion to obtain a performance evaluation, and assigning a first one of the plurality of antenna elements to a main wireless signal reception...... and transmission path and a second one of the plurality of antenna elements to a diversity wireless signal reception path based on the performance evaluation....

  6. GAIN RATIO BASED FEATURE SELECTION METHOD FOR PRIVACY PRESERVATION

    Directory of Open Access Journals (Sweden)

    R. Praveena Priyadarsini

    2011-04-01

    Full Text Available Privacy-preservation is a step in data mining that tries to safeguard sensitive information from unsanctioned disclosure and hence protecting individual data records and their privacy. There are various privacy preservation techniques like k-anonymity, l-diversity and t-closeness and data perturbation. In this paper k-anonymity privacy protection technique is applied to high dimensional datasets like adult and census. since, both the data sets are high dimensional, feature subset selection method like Gain Ratio is applied and the attributes of the datasets are ranked and low ranking attributes are filtered to form new reduced data subsets. K-anonymization privacy preservation technique is then applied on reduced datasets. The accuracy of the privacy preserved reduced datasets and the original datasets are compared for their accuracy on the two functionalities of data mining namely classification and clustering using naïve Bayesian and k-means algorithm respectively. Experimental results show that classification and clustering accuracy are comparatively the same for reduced k-anonym zed datasets and the original data sets.

  7. [X-ray evaluation of renal function in children with hydronephrosis as a criterion in the selection of therapeutic tactics].

    Science.gov (United States)

    Bosin, V Iu; Murvanidze, D D; Sturua, D G; Nabokov, A K; Soloshenko, V N

    1989-01-01

    The anatomic parameters of the kidneys and the rate of glomerular filtration were measured in 77 children with unilateral hydronephrosis and in 27 children with nonobstructive diseases of the urinary tract according to the clearance of an opaque medium during excretory urography. Alterations in the anatomic parameters of the kidneys in obstructive affection did not reflect the gravity of functional disorders. It has been established that there is a possibility of carrying out a separate assessment of filtration function of the hydronephrotic and contralateral kidneys. A new diagnostic criterion is offered, namely an index of relative clearance, which enables one to measure the degree of compensatory phenomena in the preserved glomeruli and the extent of sclerotic process. It has been demonstrated that accurate measurement of the functional parameters of the affected kidney should underlie the treatment choice in children with unilateral hydronephrosis.

  8. Neutron shielding calculations in a proton therapy facility based on Monte Carlo simulations and analytical models: Criterion for selecting the method of choice

    International Nuclear Information System (INIS)

    Titt, U.; Newhauser, W. D.

    2005-01-01

    Proton therapy facilities are shielded to limit the amount of secondary radiation to which patients, occupational workers and members of the general public are exposed. The most commonly applied shielding design methods for proton therapy facilities comprise semi-empirical and analytical methods to estimate the neutron dose equivalent. This study compares the results of these methods with a detailed simulation of a proton therapy facility by using the Monte Carlo technique. A comparison of neutron dose equivalent values predicted by the various methods reveals the superior accuracy of the Monte Carlo predictions in locations where the calculations converge. However, the reliability of the overall shielding design increases if simulation results, for which solutions have not converged, e.g. owing to too few particle histories, can be excluded, and deterministic models are being used at these locations. Criteria to accept or reject Monte Carlo calculations in such complex structures are not well understood. An optimum rejection criterion would allow all converging solutions of Monte Carlo simulation to be taken into account, and reject all solutions with uncertainties larger than the design safety margins. In this study, the optimum rejection criterion of 10% was found. The mean ratio was 26, 62% of all receptor locations showed a ratio between 0.9 and 10, and 92% were between 1 and 100. (authors)

  9. Selected financial and operating ratios of public power systems

    International Nuclear Information System (INIS)

    Moody, D.

    1993-01-01

    In 1992, the American Public Power Association published its fourth report on financial and operating ratios. Based on 1990 data for the largest public power distribution systems, the report examined 21 categories of ratio indicators that can be used by public power distribution systems to assess their performance relative to the utilities of of comparable size and in the same geographic region. The 394 utilities summarized in the report are those that are required to file financial statements with the Energy Information Administration (EIA). Ratios were calculated from financial and operating data reported by utilities to the EIA. Data are presented for the following ratios: (1) revenue per kW/hr; (2) revenue for customer; (3) debt to total assets; (4) operating ratio; (5) current ratio; (6) times interest earned; (7) net income per revenue dollar; (8) uncollectible accounts per revenue dollar; (9) retail MW hr sales per manpower generation employee; (10) retail customers per nonpower generation employee; (11) total operation and maintenane expense per kW hr sold; (12) total operation and maintenance expense per retail customer; (13) total power supply expense kW hr sold; (14) purchased power cost per kW hr; (15) production expense per not kW hr; (16) retail customers for with reader; (17) distribution operation and maintenance expenses per retail customer; (18) distribution operation and maintenance expenses per circuit mile; (19) customer accounting, customer service and sales expenses per retail customers; (20) administration and general expenses per retail customer; (21) labor expense per worker-hour; (22) OSHA incidence rate; and (23) the system average interruptible duration index

  10. Embedding filtering criteria into a wrapper marker selection method for brain tumor classification: an application on metabolic peak area ratios

    International Nuclear Information System (INIS)

    Kounelakis, M G; Zervakis, M E; Giakos, G C; Postma, G J; Buydens, L M C; Kotsiakis, X

    2011-01-01

    The purpose of this study is to identify reliable sets of metabolic markers that provide accurate classification of complex brain tumors and facilitate the process of clinical diagnosis. Several ratios of metabolites are tested alone or in combination with imaging markers. A wrapper feature selection and classification methodology is studied, employing Fisher's criterion for ranking the markers. The set of extracted markers that express statistical significance is further studied in terms of biological behavior with respect to the brain tumor type and grade. The outcome of this study indicates that the proposed method by exploiting the intrinsic properties of data can actually reveal reliable and biologically relevant sets of metabolic markers, which form an important adjunct toward a more accurate type and grade discrimination of complex brain tumors

  11. Concentration ratios for BIOPATH: selection of the soil-to-plant concentration ratio database

    International Nuclear Information System (INIS)

    Grogan, H.A.

    1985-01-01

    In Switzerland, high-level radioactive waste is planned to be deposited in deep crystalline formations. 'BIOPATH' is the computer code which has been used to simulate the movement of radionuclides in the biosphere, in order to calculate the doses to man. The key parameter used in the model on which the code is based is the concentration ratio (CR). This specifies the transfer of individual radionuclides via the various foodchains, ultimately to man. Five types of CR are required for the model, namely soil to plant, intake by cattle to milk, intake by cattle to meat, intake by poultry to eggs and from water to fish. Each of these CR are discussed in turn; it is shown that soil to plant CR exhibit a variability that greatly exceeds that observed in the other types of CR and for this reason the report goes on to consider these in much closer detail. The different methods and experimental techniques used to derive soil to plant CR are examined and assessed, to allow evaluation of a meaningful data base for use in BIOPATH. The report concludes by examining the data available for each radionuclide in turn and listing a recommended CR for it, to input into the BIOPATH model. (author)

  12. Selective interactions among Rh, ABO, and sex ratio of newborns.

    Science.gov (United States)

    Valenzuela, C Y; Walton, R

    1985-01-01

    The hypothesis that the Rh and ABO blood systems behave like the HLA system in relation to mother-conception tolerance-rejection mechanisms was tested in 25,501 mother-infant pairs. According to this hypothesis, heterozygotes carrying a paternal gene that is not present in their mothers should be better tolerated than homozygotes. Significantly more BO infants born to AO mothers. AO infants born to BO mothers, Rh(+) heterozygotes born to Rh(-) mothers, and less significantly AO infants born to OO mothers confirm the hypothesis. Fewer homozygotes occurred in Rh(-) infants born to Rh(+) mothers and in O infants born to non-O mothers. Deviations from the Hardy-Weinberg equilibrium found in the ABO system were modified by the Rh and sex of the infant. These data strongly support the hypothesis that at least two feto-maternal systems influence the destiny of pregnancies: the classical known incompatibility system which operates late in pregnancy and a new one which is based on the induction of maternal tolerance early in pregnancy: maternal tolerance seems to be better elicited by heterozygous eggs or embryos carrying a gene not present in the mother. The data also support the hypothesis that the sex ratio is influenced by feto-maternal tolerance-rejection mechanisms associated with the ABO and Rh systems.

  13. The Distributed Criterion Design

    Science.gov (United States)

    McDougall, Dennis

    2006-01-01

    This article describes and illustrates a novel form of the changing criterion design called the distributed criterion design, which represents perhaps the first advance in the changing criterion design in four decades. The distributed criterion design incorporates elements of the multiple baseline and A-B-A-B designs and is well suited to applied…

  14. A potential new selection criterion for breeding winter barley optimal protein and amino acid profiles for liquid pig feed

    DEFF Research Database (Denmark)

    Christensen, Jesper Bjerg; Blaabjerg, Karoline; Poulsen, Hanne Damgaard

    The hypothesis is that cereal proteases in liquid feed degrade and convert water insoluble storage protein into water soluble protein, which may improve the digestibility of protein in pigs compared with dry feeding. Protein utilization is increased by matching the amino acid (AAs) content...... of the diet as close as possible to the pigs’ requirement. By improving the availability of isoleucine, leucine, histidine and phenylalanine, which are limiting and commercial unavailable, the amount of crude protein in the pig feed can be reduced, resulting in a decreased excretion of nitrogen. The aim...... of glutamic acid revealed differences between the cultivars and the solubilised protein at all three times. These preliminary results may indicate that improvements of the nitrogen utilization in pigs fed soaked winter barley depends on the choice of cultivar and soaking time, and may serve as a new selection...

  15. Sex ratio selection and multi-factorial sex determination in the housefly : A dynamic model

    NARCIS (Netherlands)

    Kozielska, M.A.; Pen, I.R.; Beukeboom, L.W.; Weissing, F.J.

    Sex determining (SD) mechanisms are highly variable between different taxonomic groups and appear to change relatively quickly during evolution. Sex ratio selection could be a dominant force causing such changes. We investigate theoretically the effect of sex ratio selection on the dynamics of a

  16. Technique for Selecting Optimum Fan Compression Ratio based on the Effective Power Plant Parameters

    Directory of Open Access Journals (Sweden)

    I. I. Kondrashov

    2016-01-01

    Full Text Available Nowadays, civilian aircrafts occupy the major share of global aviation industry market. As to medium and long - haul aircrafts, turbofans with separate exhaust streams are widely used. Here, fuel efficiency is the main criterion of this engine. The paper presents the research results of the mutual influence of fan pressure ratio and bypass ratio on the effective specific fuel consumption. Shows the increasing bypass ratio to be a rational step for reducing the fuel consumption. Also considers the basic features of engines with a high bypass ratio. Among the other working process parameters, fan pressure ratio and bypass ratio are the most relevant for consideration as they are the most structural variables at a given level of technical excellence. The paper presents the dependence of the nacelle drag coefficient on the engine bypass ratio. For computation were adopted the projected parameters of prospective turbofans to be used in the power plant of the 180-seat medium-haul aircraft. Computation of the engine cycle was performed in Mathcad using these data, with fan pressure ratio and bypass ratio being varied. The combustion chamber gas temperature, the overall pressure ratio and engine thrust remained constant. Pressure loss coefficients, the efficiency of the engine components and the amount of air taken for cooling also remained constant. The optimal parameters corresponding to the minimum effective specific fuel consumption were found as the result of computation. The paper gives recommendations for adjusting optimal parameters, depending on the considered external factors, such as weight of engine and required fuel reserve. The obtained data can be used to estimate parameters of future turbofan engines with high bypass ratio.

  17. When selection ratios are high: predicting the expatriation willingness of prospective domestic entry-level job applicants

    NARCIS (Netherlands)

    Mol, S.T.; Born, M.P.; Willemsen, M.E.; van der Molen, H.T.; Derous, E.

    2009-01-01

    High expatriate selection ratios thwart the ability of multinational organizations to select expatriates. Reducing the selection ratio may be accomplished by selecting those applicants for entry level domestic positions who have expatriate aspirations. Regression analyses conducted on data from a

  18. Do candidate reactions relate to job performance or affect criterion-related validity? A multistudy investigation of relations among reactions, selection test scores, and job performance.

    Science.gov (United States)

    McCarthy, Julie M; Van Iddekinge, Chad H; Lievens, Filip; Kung, Mei-Chuan; Sinar, Evan F; Campion, Michael A

    2013-09-01

    Considerable evidence suggests that how candidates react to selection procedures can affect their test performance and their attitudes toward the hiring organization (e.g., recommending the firm to others). However, very few studies of candidate reactions have examined one of the outcomes organizations care most about: job performance. We attempt to address this gap by developing and testing a conceptual framework that delineates whether and how candidate reactions might influence job performance. We accomplish this objective using data from 4 studies (total N = 6,480), 6 selection procedures (personality tests, job knowledge tests, cognitive ability tests, work samples, situational judgment tests, and a selection inventory), 5 key candidate reactions (anxiety, motivation, belief in tests, self-efficacy, and procedural justice), 2 contexts (industry and education), 3 continents (North America, South America, and Europe), 2 study designs (predictive and concurrent), and 4 occupational areas (medical, sales, customer service, and technological). Consistent with previous research, candidate reactions were related to test scores, and test scores were related to job performance. Further, there was some evidence that reactions affected performance indirectly through their influence on test scores. Finally, in no cases did candidate reactions affect the prediction of job performance by increasing or decreasing the criterion-related validity of test scores. Implications of these findings and avenues for future research are discussed. PsycINFO Database Record (c) 2013 APA, all rights reserved

  19. Applying Least Absolute Shrinkage Selection Operator and Akaike Information Criterion Analysis to Find the Best Multiple Linear Regression Models between Climate Indices and Components of Cow's Milk.

    Science.gov (United States)

    Marami Milani, Mohammad Reza; Hense, Andreas; Rahmani, Elham; Ploeger, Angelika

    2016-07-23

    This study focuses on multiple linear regression models relating six climate indices (temperature humidity THI, environmental stress ESI, equivalent temperature index ETI, heat load HLI, modified HLI (HLI new ), and respiratory rate predictor RRP) with three main components of cow's milk (yield, fat, and protein) for cows in Iran. The least absolute shrinkage selection operator (LASSO) and the Akaike information criterion (AIC) techniques are applied to select the best model for milk predictands with the smallest number of climate predictors. Uncertainty estimation is employed by applying bootstrapping through resampling. Cross validation is used to avoid over-fitting. Climatic parameters are calculated from the NASA-MERRA global atmospheric reanalysis. Milk data for the months from April to September, 2002 to 2010 are used. The best linear regression models are found in spring between milk yield as the predictand and THI, ESI, ETI, HLI, and RRP as predictors with p -value < 0.001 and R ² (0.50, 0.49) respectively. In summer, milk yield with independent variables of THI, ETI, and ESI show the highest relation ( p -value < 0.001) with R ² (0.69). For fat and protein the results are only marginal. This method is suggested for the impact studies of climate variability/change on agriculture and food science fields when short-time series or data with large uncertainty are available.

  20. Ratios performance indicator evaluation of selected engineering enterprises in the northeast cohesion region

    OpenAIRE

    Šenec, Alexandr

    2014-01-01

    The paper deals with the performance indicator evaluation of selected industrial companies with a predominance of engineering production. Ratio indicators were used in order to measure business performance per unit of fixed assets and per employee. Analyzed data were obtained from companies annual reports. Trends ratio indicators were intended with the help of mathematical and statistical methods. These ratios indicator assessing the level of performance, value added and operating profit p...

  1. A New Infrared Color Criterion for the Selection of 0 < z < 7 AGNs: Application to Deep Fields and Implications for JWST Surveys

    Science.gov (United States)

    Messias, H.; Afonso, J.; Salvato, M.; Mobasher, B.; Hopkins, A. M.

    2012-08-01

    It is widely accepted that observations at mid-infrared (mid-IR) wavelengths enable the selection of galaxies with nuclear activity, which may not be revealed even in the deepest X-ray surveys. Many mid-IR color-color criteria have been explored to accomplish this goal and tested thoroughly in the literature. Besides missing many low-luminosity active galactic nuclei (AGNs), one of the main conclusions is that, with increasing redshift, the contamination by non-active galaxies becomes significant (especially at z >~ 2.5). This is problematic for the study of the AGN phenomenon in the early universe, the main goal of many of the current and future deep extragalactic surveys. In this work new near- and mid-IR color diagnostics are explored, aiming for improved efficiency—better completeness and less contamination—in selecting AGNs out to very high redshifts. We restrict our study to the James Webb Space Telescope wavelength range (0.6-27 μm). The criteria are created based on the predictions by state-of-the-art galaxy and AGN templates covering a wide variety of galaxy properties, and tested against control samples with deep multi-wavelength coverage (ranging from the X-rays to radio frequencies). We show that the colors Ks - [4.5], [4.5] - [8.0], and [8.0] - [24] are ideal as AGN/non-AGN diagnostics at, respectively, z ~ 2.5-3. However, when the source redshift is unknown, these colors should be combined. We thus develop an improved IR criterion (using Ks and IRAC bands, KI) as a new alternative at z 50%-90% level of successful AGN selection). We also propose KIM (using Ks , IRAC, and MIPS 24 μm bands, KIM), which aims to select AGN hosts from local distances to as far back as the end of reionization (0 ~ 2.5. Overall, KIM shows a ~30%-40% completeness and a >70%-90% level of successful AGN selection. KI and KIM are built to be reliable against a ~10%-20% error in flux, are based on existing filters, and are suitable for immediate use.

  2. Is body weight the most appropriate criterion to select patients eligible for low-dose pulmonary CT angiography? Analysis of objective and subjective image quality at 80 kVp in 100 patients

    Energy Technology Data Exchange (ETDEWEB)

    Szucs-Farkas, Zsolt; Strautz, Tamara; Patak, Michael A.; Kurmann, Luzia; Vock, Peter; Schindera, Sebastian T. [University Hospital and University of Berne, Department of Diagnostic, Interventional and Paediatric Radiology, Berne (Switzerland)

    2009-08-15

    The objective of this retrospective study was to assess image quality with pulmonary CT angiography (CTA) using 80 kVp and to find anthropomorphic parameters other than body weight (BW) to serve as selection criteria for low-dose CTA. Attenuation in the pulmonary arteries, anteroposterior and lateral diameters, cross-sectional area and soft-tissue thickness of the chest were measured in 100 consecutive patients weighing less than 100 kg with 80 kVp pulmonary CTA. Body surface area (BSA) and contrast-to-noise ratios (CNR) were calculated. Three radiologists analyzed arterial enhancement, noise, and image quality. Image parameters between patients grouped by BW (group 1: 0-50 kg; groups 2-6: 51-100 kg, decadelly increasing) were compared. CNR was higher in patients weighing less than 60 kg than in the BW groups 71-99 kg (P between 0.025 and <0.001). Subjective ranking of enhancement (P=0.165-0.605), noise (P=0.063), and image quality (P=0.079) did not differ significantly across all patient groups. CNR correlated moderately strongly with weight (R=-0.585), BSA (R=-0.582), cross-sectional area (R=-0.544), and anteroposterior diameter of the chest (R=-0.457; P<0.001 all parameters). We conclude that 80 kVp pulmonary CTA permits diagnostic image quality in patients weighing up to 100 kg. Body weight is a suitable criterion to select patients for low-dose pulmonary CTA. (orig.)

  3. On the Jeans criterion

    International Nuclear Information System (INIS)

    Whitworth, A.P.

    1980-01-01

    The Jeans criterion is first stated and distinguished from the Virial Theorem. Then it is discussed how the Jeans criterion can be derived from the Virial Theorem and the inherent shortcomings in this derivation. Finally, it is indicated how these shortcomings might be overcome. The Jeans criterion is a fragmentation - or condensation -criterion. An expression is given, connecting the fragmentation of an unstable extended medium into masses Msub(J). Rather than picturing the background medium fragmenting, it is probably more appropriate to envisage these masses Msub(J) 'condensing' out of the background medium. On the condensation picture some fraction of the background material separates out into coherent bound nodules under the pull of its self-gravity. For this reason the Jeans criterion is discussed as a condensation condition, reserving the term fragmentation for a different process. The Virial Theorem provides a contraction criterion. This is described with reference to a spherical cloud and is developed to derive the Jeans criterion. (U.K.)

  4. Ratio of total-to-selective extinction in the Taurus dark cloud complex

    International Nuclear Information System (INIS)

    Vrba, F.J.; Rydgren, A.E.; Space Telescope Science Institute, Baltimore, MD)

    1985-01-01

    UBVRI and JHK photometry, as well as spectral classifications are presented for seven reddened early-type field stars that are observed through the Taurus dark cloud complex. The ratio of total-to-selective extinction is derived for each star by the color-difference method. For six stars with absolute magnitudes in violet of more than 1.7 and less than 3.2 mag, a normal ratio R of total-to-selective extinction of about 3.1 is found. The mildly anomalous R value of about 3.5 for the well-studied star HD 29647 was also confirmed. The results provide further evidence that the interstellar extinction law in the Taurus dark cloud complex is basically normal for lines of sight with absolute magnitudes in violet of less than 3 mag. 24 references

  5. Recurrent selection on the Winters sex-ratio genes in Drosophila simulans.

    Science.gov (United States)

    Kingan, Sarah B; Garrigan, Daniel; Hartl, Daniel L

    2010-01-01

    Selfish genes, such as meiotic drive elements, propagate themselves through a population without increasing the fitness of host organisms. X-linked (or Y-linked) meiotic drive elements reduce the transmission of the Y (X) chromosome and skew progeny and population sex ratios, leading to intense conflict among genomic compartments. Drosophila simulans is unusual in having a least three distinct systems of X chromosome meiotic drive. Here, we characterize naturally occurring genetic variation at the Winters sex-ratio driver (Distorter on the X or Dox), its progenitor gene (Mother of Dox or MDox), and its suppressor gene (Not Much Yang or Nmy), which have been previously mapped and characterized. We survey three North American populations as well as 13 globally distributed strains and present molecular polymorphism data at the three loci. We find that all three genes show signatures of selection in North America, judging from levels of polymorphism and skews in the site-frequency spectrum. These signatures likely result from the biased transmission of the driver and selection on the suppressor for the maintenance of equal sex ratios. Coalescent modeling indicates that the timing of selection is more recent than the age of the alleles, suggesting that the driver and suppressor are coevolving under an evolutionary "arms race." None of the Winters sex-ratio genes are fixed in D. simulans, and at all loci we find ancestral alleles, which lack the gene insertions and exhibit high levels of nucleotide polymorphism compared to the derived alleles. In addition, we find several "null" alleles that have mutations on the derived Dox background, which result in loss of drive function. We discuss the possible causes of the maintenance of presence-absence polymorphism in the Winters sex-ratio genes.

  6. Optimized aspect ratios of restrained thick-wall cylinders by virtue of Poisson's ratio selection. Part two: Temperature application

    International Nuclear Information System (INIS)

    Whitty, J.P.M.; Henderson, B.; Francis, J.

    2011-01-01

    Highlights: → Incontrovertible evidence is presented that thermal stresses in cylindrical components which include nuclear reactors and containment vessels are shown to be highly dependent on the Poisson's ratio of the materials. → The key novelty is concerned with the identification of a new potential thermal applications for negative Poisson's ratio (auxetic) materials; i.e. those that get fatter when they are stretched. → Negative Poisson's ratio (auxetic) materials exhibit lower thermal stress build-up than conventional positive Poisson's ratio materials, this conjecture being proven using thermal surface plots. - Abstract: Analytical and numerical modelling have been employed to show that the choice of Poisson's ratio is one of the principal design criteria in order to reduce thermal stress build-up in isotropic materials. The modelling procedures are all twofold; consisting of a solution to a steady-state heat conduction problem followed by a linear static solution. The models developed take the form of simplistic thick-wall cylinders such model systems are applicable at macro-structural and micro-structural levels as the underlining formulations are based on the classical theory of elasticity. Generally, the results show that the Poisson's ratio of the material has a greater effect on the magnitude of the principal stresses than the aspect ratio of the cylinders investigated. Constraining the outside of these models significantly increases the thermal stresses induced. The most significant and original finding presented is that the for both freely expanding and constrained thick-wall cylinders the optimum Poisson's ratio is minus unity.

  7. EVALUATION OF N-RATIO IN SELECTING PATIENTS FOR ADJUVANT CHEMORADIOTHERAPY AFTER D2-GASTRECTOMY

    Directory of Open Access Journals (Sweden)

    Wilson Luiz da COSTA JUNIOR

    2013-12-01

    Full Text Available Context Whether adjuvant chemoradiotherapy may contribute to improve survival outcomes after D2-gastrectomy remains controvertial. Objective To explore the clinical utility of N-Ratio in selecting gastric cancer patients for adjuvant chemoradiotherapy after D2-gastrectomy. Methods A retrospective cohort study was carried out on gastric cancer patients who underwent D2-gastrectomy alone or D2-gastrectomy plus adjuvant chemoradiotherapy (INT-0116 protocol at the Hospital A. C. Camargo from September 1998 to December 2008. Statistical analysis were performed using multiple conventional methods, such as c-statistic, adjusted Cox's regression and stratified survival analysis. Results Our analysis involved 128 patients. According to c-statistic, the N-Ratio (i.e., as a continuous variable presented “area under ROC curve” (AUC of 0.713, while the number of metastatic nodes presented AUC of 0.705. After categorization, the cut-offs provide by Marchet et al. displayed the highest discriminating power – AUC value of 0.702. This N-Ratio categorization was confirmed as an independent predictor of survival using multivariate analyses. There also was a trend of better survival by adding of adjuvant chemoradiotherapy only for patients with milder degrees of lymphatic spread – 5-year survival of 23.1% vs 66.9%, respectively (HR = 0.426, 95% CI 0.150–1.202; P = 0.092. Conclusions This study confirms the N-Ratio as a tool to improve the lymph node metastasis staging in gastric cancer and suggests the cut-offs provided by Marchet et al. as the best way for its categorization after a D2-gastrectomy. In these settings, the N-Ratio appears a useful tool to select patients for adjuvant chemoradiotherapy, and the benefit of adding this type of adjuvancy to D2-gastrectomy is suggested to be limited to patients with milder degrees of lymphatic spread (i.e., NR2, 10%–25%.

  8. Optimization of Sex Ratio in a Selection Plan for Palas Prolificacy Line

    Directory of Open Access Journals (Sweden)

    Răzvan Popa

    2011-05-01

    Full Text Available The aim of the paper work is to optimize the sex ratio in a selection plan, according to model developed by King (1961, which will be proposed to be applied for prolificacy improvement in Prolific Line Palas. The method used in this paper work is modeling, which exist in the most animal breeding scientifically papers. After the simulations, we observed that the most convenient variant was that which prefigure use of 13 rams on reproduction activity. This variant offer a genetic gain per generation by 0.47497 additive standard deviations.

  9. Broadband photonic crystal fiber coupler with polarization selection of coupling ratio

    Science.gov (United States)

    Jaroszewicz, Leszek R.; Stasiewicz, Karol A.; Marć, Paweł; Szymański, Michał

    2010-09-01

    In the paper a new broadband photonic crystal fiber coupler is presented. The proper application of the biconical taper technology has been used for manufacturing the coupler without air holes collapse in LMA10 fiber (NKT Photonics Crystal). This coupler, operates in the weakly coupling condition, protects coupling operation in range from 900 nm to 1700 nm. The coupling ratio between output arms is depending on wavelength and can be tuning by selection the proper input state of polarization. It gives opportunity to use the broadband crystal fiber coupler in many applications in which it is necessary to tune a coupling between output arms during the measurement.

  10. Mean value-based power allocation and ratio selection for MIMO cognitive radio systems

    KAUST Repository

    Tourki, Kamel; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

    2013-01-01

    In this paper, we consider a spectrum sharing cognitive radio system with ratio selection using a mean value-based power allocation strategy. We first provide the exact statistics in terms of probability density function and cumulative density function of the secondary channel gain as well as of the interference channel gain. These statistics are then used to derive exact closed form expression of the secondary outage probability. Furthermore, asymptotical analysis is derived and generalized diversity gain is deduced. We validate our analysis with simulation results in a Rayleigh fading environment. © 2013 IEEE.

  11. Mean value-based power allocation and ratio selection for MIMO cognitive radio systems

    KAUST Repository

    Tourki, Kamel

    2013-06-01

    In this paper, we consider a spectrum sharing cognitive radio system with ratio selection using a mean value-based power allocation strategy. We first provide the exact statistics in terms of probability density function and cumulative density function of the secondary channel gain as well as of the interference channel gain. These statistics are then used to derive exact closed form expression of the secondary outage probability. Furthermore, asymptotical analysis is derived and generalized diversity gain is deduced. We validate our analysis with simulation results in a Rayleigh fading environment. © 2013 IEEE.

  12. Enhancements to the CALIOP Aerosol Subtyping and Lidar Ratio Selection Algorithms for Level II Version 4

    Science.gov (United States)

    Omar, A. H.; Tackett, J. L.; Vaughan, M. A.; Kar, J.; Trepte, C. R.; Winker, D. M.

    2016-12-01

    This presentation describes several enhancements planned for the version 4 aerosol subtyping and lidar ratio selection algorithms of the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) instrument. The CALIOP subtyping algorithm determines the most likely aerosol type from CALIOP measurements (attenuated backscatter, estimated particulate depolarization ratios δe, layer altitude), and surface type. The aerosol type, so determined, is associated with a lidar ratio (LR) from a discrete set of values. Some of these lidar ratios have been updated in the version 4 algorithms. In particular, the dust and polluted dust will be adjusted to reflect the latest measurements and model studies of these types. Version 4 eliminates the confusion between smoke and clean marine aerosols seen in version 3 by modifications to the elevated layer flag definitions used to identify smoke aerosols over the ocean. In the subtyping algorithms pure dust is determined by high estimated particulate depolarization ratios [δe > 0.20]. Mixtures of dust and other aerosol types are determined by intermediate values of the estimated depolarization ratio [0.075limited to mixtures of dust and smoke, the so called polluted dust aerosol type. To differentiate between mixtures of dust and smoke, and dust and marine aerosols, a new aerosol type will be added in the version 4 data products. In the revised classification algorithms, polluted dust will still defined as dust + smoke/pollution but in the marine boundary layer instances of moderate depolarization will be typed as dusty marine aerosols with a lower lidar ratio than polluted dust. The dusty marine type introduced in version 4 is modeled as a mixture of dust + marine aerosol. To account for fringes, the version 4 Level 2 algorithms implement Subtype Coalescence Algorithm for AeRosol Fringes (SCAARF) routine to detect and classify fringe of aerosol plumes that are detected at 20 km or 80 km horizontal resolution at the plume base. These

  13. Selection Of Suitable Particle Size And Particle Ratio For Japanese Cucumber Cucumis Sativus L. Plants

    Directory of Open Access Journals (Sweden)

    Galahitigama GAH

    2015-08-01

    Full Text Available This study was conducted to select the best particle size of coco peat for cucumber nurseries as well as best particle ratio for optimum plant growth and development of cucumber. The experiment was carried out in International Foodstuff Company and Faculty of Agriculture University of Ruhuna Sri Lanka during 2015 to 2016. Under experiment one three types of different particle sizes were used namely fine amp88040.5mm T2 medium 3mm-0.5mm T3 and coarse 4mm T4 with normal coco peat T1 as treatments. Complete Randomized Design CRD used as experimental design with five replicates. Germination percentage number of leaves per seedling seedling height in frequent day intervals was taken as growth parameters. Analysis of variance procedure was applied to analyze the data at 5 probability level. The results revealed that medium size particle media sieve size 0.5mm -3mm of coco peat was the best particle size for cucumber nursery practice when considered the physical and chemical properties of medium particles of coco peat. In the experiment of selecting of suitable particle ratio for cucumber plants the compressed mixture of coco peat particles that contain 70 ww unsieved coco peat 20 ww coarse particles and 10 ww coconut husk chips 5 12mm has given best results for growth performances compared to other treatments and cucumber grown in this mixture has shown maximum growth and yield performances.

  14. A Feature Selection Method Based on Fisher's Discriminant Ratio for Text Sentiment Classification

    Science.gov (United States)

    Wang, Suge; Li, Deyu; Wei, Yingjie; Li, Hongxia

    With the rapid growth of e-commerce, product reviews on the Web have become an important information source for customers' decision making when they intend to buy some product. As the reviews are often too many for customers to go through, how to automatically classify them into different sentiment orientation categories (i.e. positive/negative) has become a research problem. In this paper, based on Fisher's discriminant ratio, an effective feature selection method is proposed for product review text sentiment classification. In order to validate the validity of the proposed method, we compared it with other methods respectively based on information gain and mutual information while support vector machine is adopted as the classifier. In this paper, 6 subexperiments are conducted by combining different feature selection methods with 2 kinds of candidate feature sets. Under 1006 review documents of cars, the experimental results indicate that the Fisher's discriminant ratio based on word frequency estimation has the best performance with F value 83.3% while the candidate features are the words which appear in both positive and negative texts.

  15. Selection Algorithm for the CALIPSO Lidar Aerosol Extinction-to-Backscatter Ratio

    Science.gov (United States)

    Omar, Ali H.; Winker, David M.; Vaughan, Mark A.

    2006-01-01

    The extinction-to-backscatter ratio (S(sub a)) is an important parameter used in the determination of the aerosol extinction and subsequently the optical depth from lidar backscatter measurements. We outline the algorithm used to determine Sa for the Cloud and Aerosol Lidar and Infrared Pathfinder Spaceborne Observations (CALIPSO) lidar. S(sub a) for the CALIPSO lidar will either be selected from a look-up table or calculated using the lidar measurements depending on the characteristics of aerosol layer. Whenever suitable lofted layers are encountered, S(sub a) is computed directly from the integrated backscatter and transmittance. In all other cases, the CALIPSO observables: the depolarization ratio, delta, the layer integrated attenuated backscatter, beta, and the mean layer total attenuated color ratio, gamma, together with the surface type, are used to aid in aerosol typing. Once the type is identified, a look-up-table developed primarily from worldwide observations, is used to determine the S(sub a) value. The CALIPSO aerosol models include desert dust, biomass burning, background, polluted continental, polluted dust, and marine aerosols.

  16. Selecting Feature Subsets Based on SVM-RFE and the Overlapping Ratio with Applications in Bioinformatics.

    Science.gov (United States)

    Lin, Xiaohui; Li, Chao; Zhang, Yanhui; Su, Benzhe; Fan, Meng; Wei, Hai

    2017-12-26

    Feature selection is an important topic in bioinformatics. Defining informative features from complex high dimensional biological data is critical in disease study, drug development, etc. Support vector machine-recursive feature elimination (SVM-RFE) is an efficient feature selection technique that has shown its power in many applications. It ranks the features according to the recursive feature deletion sequence based on SVM. In this study, we propose a method, SVM-RFE-OA, which combines the classification accuracy rate and the average overlapping ratio of the samples to determine the number of features to be selected from the feature rank of SVM-RFE. Meanwhile, to measure the feature weights more accurately, we propose a modified SVM-RFE-OA (M-SVM-RFE-OA) algorithm that temporally screens out the samples lying in a heavy overlapping area in each iteration. The experiments on the eight public biological datasets show that the discriminative ability of the feature subset could be measured more accurately by combining the classification accuracy rate with the average overlapping degree of the samples compared with using the classification accuracy rate alone, and shielding the samples in the overlapping area made the calculation of the feature weights more stable and accurate. The methods proposed in this study can also be used with other RFE techniques to define potential biomarkers from big biological data.

  17. Selecting Feature Subsets Based on SVM-RFE and the Overlapping Ratio with Applications in Bioinformatics

    Directory of Open Access Journals (Sweden)

    Xiaohui Lin

    2017-12-01

    Full Text Available Feature selection is an important topic in bioinformatics. Defining informative features from complex high dimensional biological data is critical in disease study, drug development, etc. Support vector machine-recursive feature elimination (SVM-RFE is an efficient feature selection technique that has shown its power in many applications. It ranks the features according to the recursive feature deletion sequence based on SVM. In this study, we propose a method, SVM-RFE-OA, which combines the classification accuracy rate and the average overlapping ratio of the samples to determine the number of features to be selected from the feature rank of SVM-RFE. Meanwhile, to measure the feature weights more accurately, we propose a modified SVM-RFE-OA (M-SVM-RFE-OA algorithm that temporally screens out the samples lying in a heavy overlapping area in each iteration. The experiments on the eight public biological datasets show that the discriminative ability of the feature subset could be measured more accurately by combining the classification accuracy rate with the average overlapping degree of the samples compared with using the classification accuracy rate alone, and shielding the samples in the overlapping area made the calculation of the feature weights more stable and accurate. The methods proposed in this study can also be used with other RFE techniques to define potential biomarkers from big biological data.

  18. General Criterion for Harmonicity

    Science.gov (United States)

    Proesmans, Karel; Vandebroek, Hans; Van den Broeck, Christian

    2017-10-01

    Inspired by Kubo-Anderson Markov processes, we introduce a new class of transfer matrices whose largest eigenvalue is determined by a simple explicit algebraic equation. Applications include the free energy calculation for various equilibrium systems and a general criterion for perfect harmonicity, i.e., a free energy that is exactly quadratic in the external field. As an illustration, we construct a "perfect spring," namely, a polymer with non-Gaussian, exponentially distributed subunits which, nevertheless, remains harmonic until it is fully stretched. This surprising discovery is confirmed by Monte Carlo and Langevin simulations.

  19. Selectivity criterion for pyrazolo[3,4-b]pyrid[az]ine derivatives as GSK-3 inhibitors: CoMFA and molecular docking studies.

    Science.gov (United States)

    Patel, Dhilon S; Bharatam, Prasad V

    2008-05-01

    In the development of drugs targeted for GSK-3, its selective inhibition is an important requirement owing to the possibility of side effects arising from other kinases for the treatment of diabetes mellitus. A three-dimensional quantitative structure-activity relationship study (3D-QSAR) has been carried out on a set of pyrazolo[3,4-b]pyrid[az]ine derivatives, which includes non-selective and selective GSK-3 inhibitors. The CoMFA models were derived from a training set of 59 molecules. A test set containing 14 molecules (not used in model generation) was used to validate the CoMFA models. The best CoMFA model generated by applying leave-one-out (LOO) cross-validation study gave cross-validation r(cv)(2) and conventional r(conv)(2) values of 0.60 and 0.97, respectively, and r(pred)(2) value of 0.55, which provide the predictive ability of model. The developed models well explain (i) the observed variance in the activity and (ii) structural difference between the selective and non-selective GSK-3 inhibitors. Validation based on the molecular docking has also been carried out to explain the structural differences between the selective and non-selective molecules in the given series of molecules.

  20. Unified Bohm criterion

    Energy Technology Data Exchange (ETDEWEB)

    Kos, L. [LECAD Laboratory, Faculty of Mechanical Engineering, University of Ljubljana, SI-1000 Ljubljana (Slovenia); Tskhakaya, D. D.; Jelić, N. [Institute for Theoretical Physics, Fusion@ÖAW, University of Innsbruck, A-6020 Innsbruck (Austria)

    2015-09-15

    Recent decades have seen research into the conditions necessary for the formation of the monotonic potential shape in the sheath, appearing at the plasma boundaries like walls, in fluid, and kinetic approximations separately. Although either of these approaches yields a formulation commonly known as the much-acclaimed Bohm criterion (BC), the respective results involve essentially different physical quantities that describe the ion gas behavior. In the fluid approach, such a quantity is clearly identified as the ion directional velocity. In the kinetic approach, the ion behavior is formulated via a quantity (the squared inverse velocity averaged by the ion distribution function) without any clear physical significance, which is, moreover, impractical. In the present paper, we try to explain this difference by deriving a condition called here the Unified Bohm Criterion, which combines an advanced fluid model with an upgraded explicit kinetic formula in a new form of the BC. By introducing a generalized polytropic coefficient function, the unified BC can be interpreted in a form that holds, irrespective of whether the ions are described kinetically or in the fluid approximation.

  1. Coconut and sunflower oil ratios in ice cream influence subsequent food selection and intake.

    Science.gov (United States)

    Rizzo, G; Masic, U; Harrold, J A; Norton, J E; Halford, J C G

    2016-10-01

    The effect of coconut oil (CO, containing mainly medium chain triglycerides - MCTs) and sunflower oil (SO, containing mainly long chain triglycerides - LCTs) used as fat source (10% fat ice cream) in different ratios (25% CO and 75% SO - 25CO:75SO, 50% CO and 50% SO - 50CO:50SO, 75% CO and 25% SO - 75CO:25SO) was investigated to assess differences in appetite and ad-libitum (evening and snack) food intake using a single blind design. 36 healthy female participants consumed a fixed portion (150g) of ice cream 45min before an ad-libitum dinner and snacks. Appetite sensations were tracked across the day. Participants ate significantly less fat after 75CO:25SO than 25CO:75SO (p=0.007) and there was also a trend for lower fat intake in this condition as compared to 50CO:50SO (p=0.068). High fat savoury snack intake significantly decreased after 75CO:25SO in comparison with both 25CO:75SO (p=0.038) and 50CO:50SO (p=0.008). Calorie intake from snacks was also found to be significantly lower after 25CO:75SO and 50CO:50SO than 75CO:25SO (p=0.021 and 0.030 respectively). There was no effect of condition on appetite or desire ratings over the day. Eating a standard portion of ice cream containing different ratios of MCTs and LCTs can modestly influence acute food selection and intake, with MCTs manifesting their effect earlier and LCTs later due to differences in the absorption and metabolism of these lipids. However, the differences evident in the present study were small, and require further research before firm conclusions can be drawn. Copyright © 2016 Elsevier Inc. All rights reserved.

  2. Wavelength dependence of interstellar polarization and ratio of total to selective extinction

    International Nuclear Information System (INIS)

    Serkowski, K.; Mathewson, D.S.; Ford, V.L.

    1975-01-01

    Wavelength dependence of interstellar linear polarization has been observed for about 180 stars, mostly southern, in the UBVR spectral regions. A multichannel polarimeter-photometer, in which spectral regions are separated by dichroic filters, was used. Normalized wavelength dependence of interstellar linear polarization p follows closely a single empirical curve p (lambda)/p /sub max/=exp-1.15 ln 2 (lambda/sub max//lambda), where the wavelength lambda/sub max/ at which the maximum interstellar linear polarization p/sub max/ occurs takes values from 0.45 μ to 0.8 μ. Wavelength lambda/sub max/ is well correlated with the ratios of color excesses E/sub V-K//E/sub B-V/, E/sub V-K//E/sub V-R/, and E/sub V-I//E/sub V-R/. These correlations indicate that the ratio R of total to selective interstellar extinction can be found for any individual star from the relationship R = 5.5 lambda/sub max/. Polarimetry seems to be the most practical method of estimating R. A map of distribution of lambda/sub max/ on the sky, based on values for about 350 stars, indicates several well defined regions with lambda/sub max/, and hence R, clearly larger (or smaller) than the median value lambda/sub max/ = π.545 μ, corresponding to R = 3.0. The predominance of larger than average values of lambda/sub max/ among stars nearer than 0.4 kpc and the negative correlation between lambda/sub max/ and E/sub B-V/ are explained by selection effects. There is evidence of negative correlation between lambda/sub max/ and p/sub max//E/sub B-V/ suggested by Kruszewski. The lower limits for color excess of Praesepe, M67, and several globular clusters are set by their linear polarization. The largest known values of interstellar circular polarization, parallel q parallel approximately equal to 0.06 percent, were found in near-infrared for two stars with exceptionally small lambda/sub max/: star No. 12 in association VI Cygni and HD 204827. (U.S.)

  3. A new objective criterion for IRIS localization

    International Nuclear Information System (INIS)

    Basit, A.

    2010-01-01

    Iris localization is the most important step in iris recognition systems. For commonly used databases, exact data is not given which describe the true results of localization. To cope with this problem a new objective criterion for iris localization is proposed in this paper based on our visual system. A specific number of points are selected on pupil boundary, iris boundary, upper eyelid and lower eyelid using the original image and then distance from these points to the result of complete iris localization has been calculated. If the determined distance is below a certain threshold then iris localization is considered correct. Experimental results show that proposed criterion is very effective. (author)

  4. Stochastic Learning and the Intuitive Criterion in Simple Signaling Games

    DEFF Research Database (Denmark)

    Sloth, Birgitte; Whitta-Jacobsen, Hans Jørgen

    A stochastic learning process for signaling games with two types, two signals, and two responses gives rise to equilibrium selection which is in remarkable accordance with the selection obtained by the intuitive criterion......A stochastic learning process for signaling games with two types, two signals, and two responses gives rise to equilibrium selection which is in remarkable accordance with the selection obtained by the intuitive criterion...

  5. Bovine Host Genetic Variation Influences Rumen Microbial Methane Production with Best Selection Criterion for Low Methane Emitting and Efficiently Feed Converting Hosts Based on Metagenomic Gene Abundance.

    Directory of Open Access Journals (Sweden)

    Rainer Roehe

    2016-02-01

    Full Text Available Methane produced by methanogenic archaea in ruminants contributes significantly to anthropogenic greenhouse gas emissions. The host genetic link controlling microbial methane production is unknown and appropriate genetic selection strategies are not developed. We used sire progeny group differences to estimate the host genetic influence on rumen microbial methane production in a factorial experiment consisting of crossbred breed types and diets. Rumen metagenomic profiling was undertaken to investigate links between microbial genes and methane emissions or feed conversion efficiency. Sire progeny groups differed significantly in their methane emissions measured in respiration chambers. Ranking of the sire progeny groups based on methane emissions or relative archaeal abundance was consistent overall and within diet, suggesting that archaeal abundance in ruminal digesta is under host genetic control and can be used to genetically select animals without measuring methane directly. In the metagenomic analysis of rumen contents, we identified 3970 microbial genes of which 20 and 49 genes were significantly associated with methane emissions and feed conversion efficiency respectively. These explained 81% and 86% of the respective variation and were clustered in distinct functional gene networks. Methanogenesis genes (e.g. mcrA and fmdB were associated with methane emissions, whilst host-microbiome cross talk genes (e.g. TSTA3 and FucI were associated with feed conversion efficiency. These results strengthen the idea that the host animal controls its own microbiota to a significant extent and open up the implementation of effective breeding strategies using rumen microbial gene abundance as a predictor for difficult-to-measure traits on a large number of hosts. Generally, the results provide a proof of principle to use the relative abundance of microbial genes in the gastrointestinal tract of different species to predict their influence on traits e

  6. Optimal Wavelength Selection in Ultraviolet Spectroscopy for the Estimation of Toxin Reduction Ratio during Hemodialysis

    Directory of Open Access Journals (Sweden)

    Amir Ghanifar

    2016-06-01

    Full Text Available Introduction The concentration of substances, including urea, creatinine, and uric acid, can be used as an index to measure toxic uremic solutes in the blood during dialysis and interdialytic intervals. The on-line monitoring of toxin concentration allows for the clearance measurement of some low-molecular-weight solutes at any time during hemodialysis.The aim of this study was to determine the optimal wavelength for estimating the changes in urea, creatinine, and uric acid in dialysate, using ultraviolet (UV spectroscopy. Materials and Methods In this study, nine uremic patients were investigated, using on-line spectrophotometry. The on-line absorption measurements (UV radiation were performed with a spectrophotometer module, connected to the fluid outlet of the dialysis machine. Dialysate samples were obtained and analyzed, using standard biochemical methods. Optimal wavelengths for both creatinine and uric acid were selected by using a combination of genetic algorithms (GAs, i.e., GA-partial least squares (GA-PLS and interval partial least squares (iPLS. Results The Artifitial Neural Network (ANN sensitivity analysis determined the wavelengths of the UV band most suitable for estimating the concentration of creatinine and uric acid. The two optimal wavelengths were 242 and 252 nm for creatinine and 295 and 298 nm for uric acid. Conclusion It can be concluded that the reduction ratio of creatinine and uric acid (dialysis efficiency could be continuously monitored during hemodialysis by UV spectroscopy.Compared to the conventional method, which is particularly sensitive to the sampling technique and involves post-dialysis blood sampling, iterative measurements throughout the dialysis session can yield more reliable data.

  7. Tumour alpha/beta ratios and dose-rate selection in brachytherapy

    International Nuclear Information System (INIS)

    Duchesne, G.M.

    2003-01-01

    Traditionally brachytherapy employed low dose rate (LDR) techniques. Recent adoption of high dose rate (HDR) applications, addressing radiation protection concerns, has sparked debate over possible reductions in therapeutic ratio. The radiobiological characteristics of two contrasting examples, prostate cancer and cervical cancer, are examined. Both in-vitro and clinical observations of prostate cancer suggest a low α/β ratio. Labelling indices are below 2.5%, translating into long potential doubling times (Tpot ) of 16 to 61 days or more. Clinical PSA doubling times are in the order of years. Analysis of clinical endpoints in prostate cancer treated with either LDR or HDR techniques indicates that its α/β ratio may lie between 1 - 4 Gy, similar to slowly proliferating late reacting tissues. As such, therapeutic gain may arise from the use of hypofractionated HDR treatments, exploiting the sensitivity to large fraction sizes, effectively escalating dose. The slow proliferative rate also gives credence to the use of LDR, although several tumour doublings may occur during the effective treatment time, and analysis of the clinical data using a low α/β ratio suggests that LDR doses are only equivalent to 70 Gy with conventional fractionation. Cervical carcinoma is a rapidly proliferating tumour with Tpot values of 3-6 days. LDR implants were delivered over relatively short treatment times, negating repopulation effects, and the 'hyperfractionation' effect of LDR was suited to the high α/β ratio. HDR, although also preventing significant repopulation, has the potential to decrease the therapeutic ratio if low α/β , late-reacting tissues are not protected. Clinical data however show improved outcomes and reduced morbidity with HDR through reduced doses to normal tissues. Choosing the optimal dose rate in brachytherapy depends on tumour behaviour and achievable accuracy. HDR offers some advantages even for high α/β ratio tumours, and may be the technique of

  8. Sex-ratio control erodes sexual selection, revealing evolutionary feedback from adaptive plasticity

    NARCIS (Netherlands)

    Fawcett, Tim W.; Kuijper, Bram; Weissing, Franz J.; Pen, Ido

    2011-01-01

    Female choice is a powerful selective force, driving the elaboration of conspicuous male ornaments. This process of sexual selection has profound implications for many life-history decisions, including sex allocation. For example, females with attractive partners should produce more sons, because

  9. Estimation of indoor and outdoor ratios of selected volatile organic compounds in Canada

    Science.gov (United States)

    Xu, Jing; Szyszkowicz, Mieczyslaw; Jovic, Branka; Cakmak, Sabit; Austin, Claire C.; Zhu, Jiping

    2016-09-01

    Indoor air and outdoor air concentration (I/O) ratio can be used to identify the origins of volatile organic compounds (VOCs). I/O ratios of 25 VOCs in Canada were estimated based on the data collected in various areas in Canada between September 2009 and December 2011. The indoor VOC data were extracted from the Canadian Health Measures Survey (CHMS). Outdoor VOC data were obtained from Canada's National Air Pollution Surveillance (NAPS) Network. The sampling locations covered nine areas in six provinces in Canada. Indoor air concentrations were found higher than outdoor air for all studied VOCs, except for carbon tetrachloride. Two different approaches were employed to estimate the I/O ratios; both approaches produced similar I/O values. The I/O ratios obtained from this study were similar to two other Canadian studies where indoor air and outdoor air of individual dwellings were measured. However, the I/O ratios found in Canada were higher than those in European cities and in two large USA cities, possibly due to the fact that the outdoor air concentrations recorded in the Canadian studies were lower. Possible source origins identified for the studied VOCs based on their I/O ratios were similar to those reported by others. In general, chlorinated hydrocarbons, short-chain (C5, C6) n-alkanes and benzene had significant outdoor sources, while long-chain (C10sbnd C12) n-alkanes, terpenes, naphthalene and styrene had significant indoor sources. The remaining VOCs had mixed indoor and outdoor sources.

  10. No evidence for selective follicle abortion underlying primary sex ratio adjustment in pigeons

    NARCIS (Netherlands)

    Goerlich, Vivian C.; Dijkstra, Cornelis; Groothuis, Antonius

    Primary sex ratio adjustment in birds has been extensively studied, yet the underlying physiological mechanisms are far from understood. Avian females are the heterogametic sex (ZW), and the future sex of the offspring is determined at chromosome segregation during meiosis I, shortly before the

  11. The major/minor concept: dependence of the selectivity of homogeneously catalyzed reactions on reactivity ratio and concentration ratio of the intermediates.

    Science.gov (United States)

    Schmidt, Thomas; Dai, Zhenya; Drexler, Hans-Joachim; Hapke, Marko; Preetz, Angelika; Heller, Detlef

    2008-07-07

    The homogeneously catalyzed asymmetric hydrogenation of prochiral olefins with cationic Rh(I) complexes is one of the best-understood selection processes. For some of the catalyst/substrate complexes, experimental proof points out the validation of the major/minor principle; the concentration-deficient minor substrate complex, which has very high reactivity, yields the excess enantiomer. As exemplified by the reaction system of [Rh(dipamp)(MeOH)2]+/methyl (Z)-alpha-acetamidocinnamate (dipamp=1,2-bis((o-methoxyphenyl)phenylphosphino)ethane), all six of the characteristic reaction rate constants have been previously identified. Recently, it was found that the major substrate complex can also yield the major enantiomer (lock-and-key principle). The differential equation system that results from the reaction sequence can be solved numerically for different hydrogen partial pressures by including the known equilibrium constants. The result displays the concentration-time dependence of all species that exist in the catalytic cycle. On the basis of the known constants as well as further experimental evidence, this work focuses on the examination of all principal possibilities resulting from the reaction sequence and leading to different results for the stereochemical outcome. From the simulation, the following conclusions can be drawn: 1) When an intermediate has extreme reactivity, its stationary concentration can become so small that it can no longer be the source of product selectivity; 2) in principle, the major/minor and lock-and-key principles can coexist depending on the applied pressure; 3) thermodynamically determined intermediate ratios can be completely converted under reaction conditions for a selection process; and 4) the increase in enantioselectivity with increasing hydrogen partial pressure, a phenomenon that is experimentally proven but theoretically far from being well-understood, can be explained by applying both the lock-and-key as well as the major

  12. Determination of carbon isotope ratios in plant starch via selective enzymatic hydrolysis

    International Nuclear Information System (INIS)

    Schimmelmann, A.; DeNiro, M.J.

    1983-01-01

    A method for the determination of the carbon isotope ratios in bipolymers hydrolyzed by enzymatic action consists of separating the monomer by passage through a dialysis membrane and then combusting the monomer prior to isotopic analysis. The method is described for application to the analysis of starch, but it should find application for polymers than can be degraded quantitatively to monomers and/or oligomers using specific hydrolytic enzymes

  13. Review of criteria for the selection of probability distributions for wind speed data and introduction of the moment and L-moment ratio diagram methods, with a case study

    International Nuclear Information System (INIS)

    Ouarda, T.B.M.J.; Charron, C.; Chebana, F.

    2016-01-01

    Highlights: • Review of criteria used to select probability distributions to model wind speed data. • Classical and L-moment ratio diagrams are applied to wind speed data. • The diagrams allow to select the best distribution to model each wind speed sample. • The goodness-of-fit statistics are more consistent with the L-moment ratio diagram. - Abstract: This paper reviews the different criteria used in the field of wind energy to compare the goodness-of-fit of candidate probability density functions (pdfs) to wind speed records, and discusses their advantages and disadvantages. The moment ratio and L-moment ratio diagram methods are also proposed as alternative methods for the choice of the pdfs. These two methods have the advantage of allowing an easy comparison of the fit of several pdfs for several time series (stations) on a single diagram. Plotting the position of a given wind speed data set in these diagrams is instantaneous and provides more information than a goodness-of-fit criterion since it provides knowledge about such characteristics as the skewness and kurtosis of the station data set. In this paper, it is proposed to study the applicability of these two methods for the selection of pdfs for wind speed data. Both types of diagrams are used to assess the fit of the pdfs for wind speed series in the United Arab Emirates. The analysis of the moment ratio diagrams reveals that the Kappa, Log-Pearson type III and Generalized Gamma are the distributions that fit best all wind speed series. The Weibull represents the best distribution among those with only one shape parameter. Results obtained with the diagrams are compared with those obtained with goodness-of-fit statistics and a good agreement is observed especially in the case of the L-moment ratio diagram. It is concluded that these diagrams can represent a simple and efficient approach to be used as complementary method to goodness-of-fit criteria.

  14. Quantile selection procedure and assoiated distribution of ratios of order statistics from a restricted family of probability distributions

    International Nuclear Information System (INIS)

    Gupta, S.S.; Panchapakesan, S.

    1975-01-01

    A quantile selection procedure in reliability problems pertaining to a restricted family of probability distributions is discussed. This family is assumed to be star-ordered with respect to the standard normal distribution folded at the origin. Motivation for this formulation of the problem is described. Both exact and asymptotic results dealing with the distribution of the maximum of ratios of order statistics from such a family are obtained and tables of the appropriate constants, percentiles of this statistic, are given in order to facilitate the use of the selection procedure

  15. Performance Analysis of Selective Decode-and-Forward Multinode Incremental Relaying with Maximal Ratio Combining

    KAUST Repository

    Hadjtaieb, Amir

    2013-09-12

    In this paper, we propose an incremental multinode relaying protocol with arbitrary N-relay nodes that allows an efficient use of the channel spectrum. The destination combines the received signals from the source and the relays using maximal ratio Combining (MRC). The transmission ends successfully once the accumulated signal-to-noise ratio (SNR) exceeds a predefined threshold. The number of relays participating in the transmission is adapted to the channel conditions based on the feedback from the destination. The use of incremental relaying allows obtaining a higher spectral efficiency. Moreover, the symbol error probability (SEP) performance is enhanced by using MRC at the relays. The use of MRC at the relays implies that each relay overhears the signals from the source and all previous relays and combines them using MRC. The proposed protocol differs from most of existing relaying protocol by the fact that it combines both incremental relaying and MRC at the relays for a multinode topology. Our analyses for a decode-and-forward mode show that: (i) compared to existing multinode relaying schemes, the proposed scheme can essentially achieve the same SEP performance but with less average number of time slots, (ii) compared to schemes without MRC at the relays, the proposed scheme can approximately achieve a 3 dB gain.

  16. Non-selective beta-adrenergic blockade prevents reduction of the cerebral metabolic ratio during exhaustive exercise in humans

    DEFF Research Database (Denmark)

    Larsen, T.S.; Rasmussen, P.; Overgaard, M.

    2008-01-01

    Intense exercise decreases the cerebral metabolic ratio of oxygen to carbohydrates [O(2)/(glucose + (1/2)lactate)], but whether this ratio is influenced by adrenergic stimulation is not known. In eight males, incremental cycle ergometry increased arterial lactate to 15.3 +/- 4.2 mm (mean +/- s.......d.) and the arterial-jugular venous (a-v) difference from -0.02 +/- 0.03 mm at rest to 1.0 +/- 0.5 mm (P cerebral metabolic ratio decreased from 5.5 +/- 1.4 to 3.0 +/- 0.3 (P ... of a non-selective beta-adrenergic (beta(1) + beta(2)) receptor antagonist (propranolol) reduced heart rate (69 +/- 8 to 58 +/- 6 beats min(-1)) and exercise capacity (239 +/- 42 to 209 +/- 31 W; P

  17. High aspect ratio micro tool manufacturing for polymer replication using mu EDM of silicon, selective etching and electroforming

    DEFF Research Database (Denmark)

    Tosello, Guido; Bissacco, Giuliano; Tang, Peter Torben

    2008-01-01

    Mass fabrication of polymer micro components with high aspect ratio micro-structures requires high performance micro tools allowing the use of low cost replication processes such as micro injection moulding. In this regard an innovative process chain, based on a combination of micro electrical di...... discharge machining (mu EDM) of a silicon substrate, electroforming and selective etching was used for the manufacturing of a micro tool. The micro tool was employed for polymer replication by means of the injection moulding process....

  18. Using Financial Ratios to Select Companies for Tax Auditing: A Preliminary Study

    Science.gov (United States)

    Marghescu, Dorina; Kallio, Minna; Back, Barbro

    Tax auditing procedures include an investigation of the accounting records of a company and of other sources of information in order to assess whether the taxation has been based on correct and complete information. When there are found discrepancies between the accounting information and the real situation, the taxation should be corrected so that the eventual tax defaults are assessed and debited. The paper analyzes to what extent the financial performance of a company can be used as an indicator of tax defaults. We focus on one type of tax, namely employer's contribution, and four financial ratios. We evaluate the model in a study of Finnish companies by using a binomial logistic regression analysis. The study is exploratory and at a preliminary stage.

  19. A Failure Criterion for Concrete

    DEFF Research Database (Denmark)

    Ottosen, N. S.

    1977-01-01

    A four-parameter failure criterion containing all the three stress invariants explicitly is proposed for short-time loading of concrete. It corresponds to a smooth convex failure surface with curved meridians, which open in the negative direction of the hydrostatic axis, and the trace in the devi......A four-parameter failure criterion containing all the three stress invariants explicitly is proposed for short-time loading of concrete. It corresponds to a smooth convex failure surface with curved meridians, which open in the negative direction of the hydrostatic axis, and the trace...

  20. Literature review of the concentration ratios of selected radionuclides in freshwater and marine fish

    Energy Technology Data Exchange (ETDEWEB)

    Poston, T.M.; Klopfer, D.C.

    1986-09-01

    Concentration ratios (CR's) used for modeling the uptake and food chain transport of radionuclides in fish have usually been conservative; that is, at the high end of reported values. This practice ensures that the dose to the consumer of contaminated fish will not be underestimated. In many models, however, conservative values have been used for all variables that have any uncertainty associated with them. As a result the dose to the consumer is overestimated. Realistic CR values need to be developed to establish model parameters that will accurately reflect tissue burdens in fish and resulting dose rates to consumers. This report reviews and summarizes published literature on the uptake and distribution of stable and radioactive isotopes of 26 elements. Based on this review, we have made recommendations on CR values to be used for modeling the accumulation of radionuclides in fish. Our recommendations are compared with CR values reported in other publications. A generic discussion of abiotic and biotic factors that influence CR values is provided so that CR values may be adjusted based on site-specific characteristics of the fishes habitat. Recommended CR values for freshwater fish and for marine fish are listed. Although this report emphasizes radionuclides, it is applicable to stable elements as well.

  1. Literature review of the concentration ratios of selected radionuclides in freshwater and marine fish

    International Nuclear Information System (INIS)

    Poston, T.M.; Klopfer, D.C.

    1986-09-01

    Concentration ratios (CR's) used for modeling the uptake and food chain transport of radionuclides in fish have usually been conservative; that is, at the high end of reported values. This practice ensures that the dose to the consumer of contaminated fish will not be underestimated. In many models, however, conservative values have been used for all variables that have any uncertainty associated with them. As a result the dose to the consumer is overestimated. Realistic CR values need to be developed to establish model parameters that will accurately reflect tissue burdens in fish and resulting dose rates to consumers. This report reviews and summarizes published literature on the uptake and distribution of stable and radioactive isotopes of 26 elements. Based on this review, we have made recommendations on CR values to be used for modeling the accumulation of radionuclides in fish. Our recommendations are compared with CR values reported in other publications. A generic discussion of abiotic and biotic factors that influence CR values is provided so that CR values may be adjusted based on site-specific characteristics of the fishes habitat. Recommended CR values for freshwater fish and for marine fish are listed. Although this report emphasizes radionuclides, it is applicable to stable elements as well

  2. Interesterification reaction activity, fatty acid composition and selectivity ratio of soybean oil

    Directory of Open Access Journals (Sweden)

    El-Shattory, Y.

    1998-12-01

    Full Text Available The interesterification reaction was carried out by adding oleic acid to soybean oil by ratio 1:2 w/w under different conditions of temperature, stirring and catalyst percentages. Assessment of the interesterification of oils was reported by determination of saponification value, iodine value and fatty acids composition. This study showed that linolenic acid which is responsible for flavour instability of soybean oil and consider as primary factor contributing to deterioration of this oil could be reduced to less than or equals 3%.

    Se han llevado a cabo reacciones de interesterificación mediante la adición de ácido oleico a aceite de soja en la relación 1:2 w/w bajo diferentes condiciones de temperatura, agitación y porcentaje de catalizador. La evaluación de la interesterificación de los aceites se realizó por determinación del índice de saponificación, el índice de iodo y la composición en ácidos grasos. Este estudio mostró que el ácido linolénico, que es responsable de la inestabilidad del flavor del aceite de soja y considerado como factor primario que contribuye a la deterioración de este aceite, podría ser reducido a cantidades menores o iguales al 3%.

  3. Application of Multi-Objective Optimization on the Basis of Ratio Analysis (MOORA Method for Bank Branch Location Selection

    Directory of Open Access Journals (Sweden)

    Ali Gorener

    2013-04-01

    Full Text Available Location selection problem in banking is an important issue for the commercial success in competitive environment. There is a strategic fit between the location selection decision and overall performance of a new branch. Providing physical service in requested location as well as alternative distribution channels to meet profitable client needs is the current problematic to achieve the competitive advantage over the rivalry in financial system. In this paper, an integrated model has been developed to support in the decision of branch location selection for a new bank branch. Analytic Hierarchy Process (AHP technique has been conducted to prioritize of evaluation criteria, and multi-objective optimization on the basis of ratio analysis (MOORA method has been applied to rank location alternatives of bank branch.   

  4. The Slow:Fast substitution ratio reveals changing patterns of natural selection in gamma-proteobacterial genomes

    Energy Technology Data Exchange (ETDEWEB)

    Alm, Eric; Shapiro, B. Jesse

    2009-04-15

    Different microbial species are thought to occupy distinct ecological niches, subjecting each species to unique selective constraints, which may leave a recognizable signal in their genomes. Thus, it may be possible to extract insight into the genetic basis of ecological differences among lineages by identifying unusual patterns of substitutions in orthologous gene or protein sequences. We use the ratio of substitutions in slow versus fast-evolving sites (nucleotides in DNA, or amino acids in protein sequence) to quantify deviations from the typical pattern of selective constraint observed across bacterial lineages. We propose that elevated S:F in one branch (an excess of slow-site substitutions) can indicate a functionally-relevant change, due to either positive selection or relaxed evolutionary constraint. In a genome-wide comparative study of gamma-proteobacterial proteins, we find that cell-surface proteins involved with motility and secretion functions often have high S:F ratios, while information-processing genes do not. Change in evolutionary constraints in some species is evidenced by increased S:F ratios within functionally-related sets of genes (e.g., energy production in Pseudomonas fluorescens), while other species apparently evolve mostly by drift (e.g., uniformly elevated S:F across most genes in Buchnera spp.). Overall, S:F reveals several species-specific, protein-level changes with potential functional/ecological importance. As microbial genome projects yield more species-rich gene-trees, the S:F ratio will become an increasingly powerful tool for uncovering functional genetic differences among species.

  5. Discriminant Validity Assessment: Use of Fornell & Larcker criterion versus HTMT Criterion

    Science.gov (United States)

    Hamid, M. R. Ab; Sami, W.; Mohmad Sidek, M. H.

    2017-09-01

    Assessment of discriminant validity is a must in any research that involves latent variables for the prevention of multicollinearity issues. Fornell and Larcker criterion is the most widely used method for this purpose. However, a new method has emerged for establishing the discriminant validity assessment through heterotrait-monotrait (HTMT) ratio of correlations method. Therefore, this article presents the results of discriminant validity assessment using these methods. Data from previous study was used that involved 429 respondents for empirical validation of value-based excellence model in higher education institutions (HEI) in Malaysia. From the analysis, the convergent, divergent and discriminant validity were established and admissible using Fornell and Larcker criterion. However, the discriminant validity is an issue when employing the HTMT criterion. This shows that the latent variables under study faced the issue of multicollinearity and should be looked into for further details. This also implied that the HTMT criterion is a stringent measure that could detect the possible indiscriminant among the latent variables. In conclusion, the instrument which consisted of six latent variables was still lacking in terms of discriminant validity and should be explored further.

  6. Broadband non-selective excitation of plutonium isotopes for isotope ratio measurements in resonance ionization mass spectrometry: a theoretical study.

    Science.gov (United States)

    Sankari, M

    2012-10-15

    Making isotope ratio measurements with minimum isotope bias has always been a challenging task to mass spectrometrists, especially for the specific case of plutonium, owing to the strategic importance of the element. In order to use resonance ionization mass spectrometry (RIMS) as a tool for isotope ratio measurements, optimization of the various laser parameters and other atomic and system parameters is critical to minimize isotopic biases. Broadband simultaneous non-selective excitation of the isotopes of plutonium in the triple resonance excitation scheme with λ(1) = 420.77 nm, λ(2) = 847.28 nm, and λ(3) = 767.53 nm based on density matrix formalism has been theoretically computed for the determination of isotope ratios. The effects of the various laser parameters and other factors such as the atomization temperature and the dimensions of the atomic beam on the estimation of isotope ratios were studied. The effects of Doppler broadening, and time-dependent excitation parameters such as Rabi frequencies, ionization rate and the effect of non-Lorenztian lineshape have all been incorporated. The average laser powers and bandwidths for the three-excitation steps were evaluated for non-selective excitation. The laser intensity required to saturate the three-excitation steps were studied. The two-dimensional lineshape contour and its features were investigated, while the reversal of peak asymmetry of two-step and two-photon excitation peaks under these conditions is discussed. Optimized powers for the non-selective ionization of the three transitions were calculated as 545 mW, 150 mW and 545 mW and the laser bandwidth for all the three steps was ~20 GHz. The isotopic bias between the resonant and off-resonant isotope under the optimized conditions was no more than 9%, which is better than an earlier reported value. These optimized laser power and bandwidth conditions are better than in the earlier experimental work since these comprehensive calculations yield

  7. Distance criterion for hydrogen bond

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Distance criterion for hydrogen bond. In a D-H ...A contact, the D...A distance must be less than the sum of van der Waals Radii of the D and A atoms, for it to be a hydrogen bond.

  8. Time to Criterion: An Experimental Study.

    Science.gov (United States)

    Anderson, Lorin W.

    The purpose of the study was to investigate the magnitude of individual differences in time-to-criterion and the stability of these differences. Time-to-criterion was defined in two ways: the amount of elapsed time required to attain the criterion level and the amount of on-task time required to attain the criterion level. Ninety students were…

  9. NON-CONVENTIONAL MACHINING PROCESSES SELECTION USING MULTI-OBJECTIVE OPTIMIZATION ON THE BASIS OF RATIO ANALYSIS METHOD

    Directory of Open Access Journals (Sweden)

    MILOŠ MADIĆ

    2015-11-01

    Full Text Available The role of non-conventional machining processes (NCMPs in today’s manufacturing environment has been well acknowledged. For effective utilization of the capabilities and advantages of different NCMPs, selection of the most appropriate NCMP for a given machining application requires consideration of different conflicting criteria. The right choice of the NCMP is critical to the success and competitiveness of the company. As the NCMP selection problem involves consideration of different conflicting criteria, of different relative importance, the multi-criteria decision making (MCDM methods are very useful in systematical selection of the most appropriate NCMP. This paper presents the application of a recent MCDM method, i.e., the multi-objective optimization on the basis of ratio analysis (MOORA method to solve NCMP selection which has been defined considering different performance criteria of four most widely used NCMPs. In order to determine the relative significance of considered quality criteria a pair-wise comparison matrix of the analytic hierarchy process was used. The results obtained using the MOORA method showed perfect correlation with those obtained by the technique for order preference by similarity to ideal solution (TOPSIS method which proves the applicability and potentiality of this MCDM method for solving complex NCMP selection problems.

  10. Molecular signature of epistatic selection: interrogating genetic interactions in the sex-ratio meiotic drive of Drosophila simulans.

    Science.gov (United States)

    Chevin, Luis-Miguel; Bastide, Héloïse; Montchamp-Moreau, Catherine; Hospital, Frédéric

    2009-06-01

    Fine scale analyses of signatures of selection allow assessing quantitative aspects of a species' evolutionary genetic history, such as the strength of selection on genes. When several selected loci lie in the same genomic region, their epistatic interactions may also be investigated. Here, we study how the neutral polymorphism pattern was shaped by two close recombining loci that cause 'sex-ratio' meiotic drive in Drosophila simulans, as an example of strong selection with potentially strong epistasis. We compare the polymorphism data observed in a natural population with the results of forward stochastic simulations under several contexts of epistasis between the candidate loci for the drive. We compute the likelihood of different possible scenarios, in order to determine which configuration is most consistent with the data. Our results highlight that fine scale analyses of well-chosen candidate genomic regions provide information-rich data that can be used to investigate the genotype-phenotype-fitness map, which can hardly be studied in genome-wide analyses. We also emphasize that initial conditions and time of observation (here, time after the interruption of a partial selective sweep) are crucial parameters in the interpretation of real data, while these are often overlooked in theoretical studies.

  11. Efficiency of selection methods for increased ratio of pupal-larval to adult-larval weight gains in Tribolium.

    Science.gov (United States)

    Campo, J L; Cobos, P

    1994-01-12

    Four lines of Tribolium castaneum were selected in each of three replicates for increased ratio of (pupal-larval) to (adult-larval) weight gains, using selection for increased (pupal-larval) weight gain (PL), selection for decreased (adult-larval) weight gain (AL), direct selection for the ratio (R) and linear selection index of larval, pupal and adult weights (I), respectively, for four generations. Linear index was calculated with economic weights of m(2) -m(3) , m(3) -m(1) and m(1) -m(2) , respectively, with m(1) , m(2) and m(3) being the means for larval, pupal and adult weights. Selection to increase the ratio is considered to be a method to maximize the mean response in (adult-larval) weight while controlling the response in (pupal-adult) weight, and as a form of antagonistic selection to increase the weight gain during a given age period relative to the gain at another age period. Larval, pupal and adult weights were measured at 14, 21 and 28 days after adult emergence, respectively. The selected proportion was 20 % in all lines. The response observed for the ratio differed significantly among lines (p adulto-peso de larva en Tribolium Cuatro líneas de Tribolium castaneum fueron seleccionadas en cada una de tres repeticiones para incrementar el cociente (peso de pupa-peso de larva)/(peso de adulto-peso de larva); la línea PL fue seleccionada para aumentar la diferencia (peso de pupa-pesp de larva), la línea AL fue seleccionada para disminuir la diferencia (peso de adulto-peso de larva), fa línea R fue seleccionada directamente para el cociente, y la línea I fue seleccionada por medio de un índice lineal basado en los pesos de larva, pupa y adulto, durante cuatro generaciones. El índice lineal se calculó con pesos económicos de (m(2) -m(3) ), (m(3) -m(1) ), y (m(1) -m(2) ) respectivamentee, siendo m(1) , m(2) , y m(3) los valores medios para el peso de larva, pupa y adulto. La selección para aumentar el cociente indicado es un método para maximizar

  12. Inviscid criterion for decomposing scales

    Science.gov (United States)

    Zhao, Dongxiao; Aluie, Hussein

    2018-05-01

    The proper scale decomposition in flows with significant density variations is not as straightforward as in incompressible flows, with many possible ways to define a "length scale." A choice can be made according to the so-called inviscid criterion [Aluie, Physica D 24, 54 (2013), 10.1016/j.physd.2012.12.009]. It is a kinematic requirement that a scale decomposition yield negligible viscous effects at large enough length scales. It has been proved [Aluie, Physica D 24, 54 (2013), 10.1016/j.physd.2012.12.009] recently that a Favre decomposition satisfies the inviscid criterion, which is necessary to unravel inertial-range dynamics and the cascade. Here we present numerical demonstrations of those results. We also show that two other commonly used decompositions can violate the inviscid criterion and, therefore, are not suitable to study inertial-range dynamics in variable-density and compressible turbulence. Our results have practical modeling implication in showing that viscous terms in Large Eddy Simulations do not need to be modeled and can be neglected.

  13. EDDINGTON RATIO DISTRIBUTION OF X-RAY-SELECTED BROAD-LINE AGNs AT 1.0 < z < 2.2

    International Nuclear Information System (INIS)

    Suh, Hyewon; Hasinger, Günther; Steinhardt, Charles; Silverman, John D.; Schramm, Malte

    2015-01-01

    We investigate the Eddington ratio distribution of X-ray-selected broad-line active galactic nuclei (AGNs) in the redshift range 1.0 < z < 2.2, where the number density of AGNs peaks. Combining the optical and Subaru/Fiber Multi Object Spectrograph near-infrared spectroscopy, we estimate black hole masses for broad-line AGNs in the Chandra Deep Field South (CDF-S), Extended Chandra Deep Field South (E-CDF-S), and the XMM-Newton Lockman Hole (XMM-LH) surveys. AGNs with similar black hole masses show a broad range of AGN bolometric luminosities, which are calculated from X-ray luminosities, indicating that the accretion rate of black holes is widely distributed. We find a substantial fraction of massive black holes accreting significantly below the Eddington limit at z ≲ 2, in contrast to what is generally found for luminous AGNs at high redshift. Our analysis of observational selection biases indicates that the “AGN cosmic downsizing” phenomenon can be simply explained by the strong evolution of the comoving number density at the bright end of the AGN luminosity function, together with the corresponding selection effects. However, one might need to consider a correlation between the AGN luminosity and the accretion rate of black holes, in which luminous AGNs have higher Eddington ratios than low-luminosity AGNs, in order to understand the relatively small fraction of low-luminosity AGNs with high accretion rates in this epoch. Therefore, the observed downsizing trend could be interpreted as massive black holes with low accretion rates, which are relatively fainter than less-massive black holes with efficient accretion

  14. Judging Criterion of Controlled Structures with Closely Spaced Natural Frequencies

    International Nuclear Information System (INIS)

    Xie Faxiang; Sun Limin

    2010-01-01

    The structures with closely spaced natural frequencies widely exist in civil engineering; however, the judging criterion of the density of closely spaced frequencies is in dispute. This paper suggests a judging criterion for structures with closely spaced natural frequencies based on the analysis on a controlled 2-DOF structure. The analysis results indicate that the optimal control gain of the structure with velocity feedback is dependent on the frequency density parameter of structure and the maximum attainable additional modal damping ratio is 1.72 times of the frequency density parameter when state feedback is applied. Based on a brief review on the previous researches, a judging criterion related the minimum frequency density parameter and the required mode damping ratio was proposed.

  15. Criterion for selection of quasi-equilibrium and quasi-frozen flows of chemically reacting mixture N2O4 reversible 2NO2reversible 2NO+O2 with heat isobaric supply (removal)

    International Nuclear Information System (INIS)

    Kostik, G.Eh.; Shiryaeva, N.M.

    1979-01-01

    Is suggested the criterion of quasi-equilibrium and quasi-frozen flows with isobaric heat supply (removal), including the basic external factors, which affect on the kinetics of chemical process. This criterion is the complex [g/Fq], where g is the coolant rate, F is the channel cross-section, q is the heat flow. Estimated formulae for quasi-equilibrium [g/Fq]sub(e) and quasi-frozen [g/Fq]sub(f) flows are obtained. The states of deviation from equilibrium and frozen conditions in linear region are considered, are listed graphical dependences lg[g/Fq]sub(e), lg[g/Fq]sub(el), lg[g/Fq]sub(f), lg[g/Eq]sub(fl), as functions of equilibrium parameter Tsub(e), pressure and frozen coordinate of epsilonsub(2f) reaction. This graphs give the possibility to estimate rapidly and obviously the flow character of chemically reacting coolant

  16. An extended geometric criterion for chaos in the Dicke model

    International Nuclear Information System (INIS)

    Li Jiangdan; Zhang Suying

    2010-01-01

    We extend HBLSL's (Horwitz, Ben Zion, Lewkowicz, Schiffer and Levitan) new Riemannian geometric criterion for chaotic motion to Hamiltonian systems of weak coupling of potential and momenta by defining the 'mean unstable ratio'. We discuss the Dicke model of an unstable Hamiltonian system in detail and show that our results are in good agreement with that of the computation of Lyapunov characteristic exponents.

  17. On the Modified Barkhausen Criterion

    DEFF Research Database (Denmark)

    Lindberg, Erik; Murali, K.

    2016-01-01

    Oscillators are normally designed according to the Modified Barkhausen Criterion i.e. the complex pole pair is moved out in RHP so that the linear circuit becomes unstable. By means of the Mancini Phaseshift Oscillator it is demonstrated that the distortion of the oscillator may be minimized by i...... by introducing a nonlinear ”Hewlett Resistor” so that the complex pole-pair is in the RHP for small signals and in the LHP for large signals i.e. the complex pole pair of the instant linearized small signal model is moving around the imaginary axis in the complex frequency plane....

  18. Fault Diagnosis of Three Phase Induction Motor Using Current Signal, MSAF-Ratio15 and Selected Classifiers

    Directory of Open Access Journals (Sweden)

    Glowacz A.

    2017-12-01

    Full Text Available A degradation of metallurgical equipment is normal process depended on time. Some factors such as: operation process, friction, high temperature can accelerate the degradation process of metallurgical equipment. In this paper the authors analyzed three phase induction motors. These motors are common used in the metallurgy industry, for example in conveyor belt. The diagnostics of such motors is essential. An early detection of faults prevents financial loss and downtimes. The authors proposed a technique of fault diagnosis based on recognition of currents. The authors analyzed 4 states of three phase induction motor: healthy three phase induction motor, three phase induction motor with 1 faulty rotor bar, three phase induction motor with 2 faulty rotor bars, three phase induction motor with faulty ring of squirrel-cage. An analysis was carried out for original method of feature extraction called MSAF-RATIO15 (Method of Selection of Amplitudes of Frequencies – Ratio 15% of maximum of amplitude. A classification of feature vectors was performed by Bayes classifier, Linear Discriminant Analysis (LDA and Nearest Neighbour classifier. The proposed technique of fault diagnosis can be used for protection of three phase induction motors and other rotating electrical machines. In the near future the authors will analyze other motors and faults. There is also idea to use thermal, acoustic, electrical, vibration signal together.

  19. Towards chaos criterion in quantum field theory

    OpenAIRE

    Kuvshinov, V. I.; Kuzmin, A. V.

    2002-01-01

    Chaos criterion for quantum field theory is proposed. Its correspondence with classical chaos criterion in semi-classical regime is shown. It is demonstrated for real scalar field that proposed chaos criterion can be used to investigate stability of classical solutions of field equations.

  20. Selective dopamine D3 receptor antagonism by SB-277011A attenuates cocaine reinforcement as assessed by progressive-ratio and variable-cost–variable-payoff fixed-ratio cocaine self-administration in rats

    OpenAIRE

    Xi, Zheng-Xiong; Gilbert, Jeremy G.; Pak, Arlene C.; Ashby, Charles R.; Heidbreder, Christian A.; Gardner, Eliot L.

    2005-01-01

    In rats, acute administration of SB-277011A, a highly selective dopamine (DA) D3 receptor antagonist, blocks cocaine-enhanced brain stimulation reward, cocaine-seeking behaviour and reinstatement of cocaine-seeking behaviour. Here, we investigated whether SB-277011A attenuates cocaine reinforcement as assessed by cocaine self-administration under variable-cost–variable-payoff fixed-ratio (FR) and progressive-ratio (PR) reinforcement schedules. Acute i.p. administration of SB-277011A (3–24 mg/...

  1. Criterion for the engineering performance of carbon materials under neutron irradiation

    International Nuclear Information System (INIS)

    Virgil'ev, Yu.S.

    2002-01-01

    The criterion for the engineering performance and substation of its applicability to the reactor graphite are proposed. The complex indicator, representing the ratio of strength limits by compression and bending is proposed as the above criterion, characterizing the graphite quality. The growth of this criterion indicates the accumulation of large heterogeneities microcracks of technological or radiation character. The decrease in this indicator testifies to the growth of small heterogeneities, and consequently to the increase in the graphite engineering performance [ru

  2. The co-feature ratio, a novel method for the measurement of chromatographic and signal selectivity in LC-MS-based metabolomics

    International Nuclear Information System (INIS)

    Elmsjö, Albert; Haglöf, Jakob; Engskog, Mikael K.R.; Nestor, Marika; Arvidsson, Torbjörn; Pettersson, Curt

    2017-01-01

    Evaluation of analytical procedures, especially in regards to measuring chromatographic and signal selectivity, is highly challenging in untargeted metabolomics. The aim of this study was to suggest a new straightforward approach for a systematic examination of chromatographic and signal selectivity in LC-MS-based metabolomics. By calculating the ratio between each feature and its co-eluting features (the co-features), a measurement of the chromatographic selectivity (i.e. extent of co-elution) as well as the signal selectivity (e.g. amount of adduct formation) of each feature could be acquired, the co-feature ratio. This approach was used to examine possible differences in chromatographic and signal selectivity present in samples exposed to three different sample preparation procedures. The capability of the co-feature ratio was evaluated both in a classical targeted setting using isotope labelled standards as well as without standards in an untargeted setting. For the targeted analysis, several metabolites showed a skewed quantitative signal due to poor chromatographic selectivity and/or poor signal selectivity. Moreover, evaluation of the untargeted approach through multivariate analysis of the co-feature ratios demonstrated the possibility to screen for metabolites displaying poor chromatographic and/or signal selectivity characteristics. We conclude that the co-feature ratio can be a useful tool in the development and evaluation of analytical procedures in LC-MS-based metabolomics investigations. Increased selectivity through proper choice of analytical procedures may decrease the false positive and false negative discovery rate and thereby increase the validity of any metabolomic investigation. - Highlights: • The co-feature ratio (CFR) is introduced. • CFR measures chromatographic and signal selectivity of a feature. • CFR can be used for evaluating experimental procedures in metabolomics. • CFR can aid in locating features with poor selectivity.

  3. The co-feature ratio, a novel method for the measurement of chromatographic and signal selectivity in LC-MS-based metabolomics

    Energy Technology Data Exchange (ETDEWEB)

    Elmsjö, Albert, E-mail: Albert.Elmsjo@farmkemi.uu.se [Department of Medicinal Chemistry, Division of Analytical Pharmaceutical Chemistry, Uppsala University (Sweden); Haglöf, Jakob; Engskog, Mikael K.R. [Department of Medicinal Chemistry, Division of Analytical Pharmaceutical Chemistry, Uppsala University (Sweden); Nestor, Marika [Department of Immunology, Genetics and Pathology, Uppsala University (Sweden); Arvidsson, Torbjörn [Department of Medicinal Chemistry, Division of Analytical Pharmaceutical Chemistry, Uppsala University (Sweden); Medical Product Agency, Uppsala (Sweden); Pettersson, Curt [Department of Medicinal Chemistry, Division of Analytical Pharmaceutical Chemistry, Uppsala University (Sweden)

    2017-03-01

    Evaluation of analytical procedures, especially in regards to measuring chromatographic and signal selectivity, is highly challenging in untargeted metabolomics. The aim of this study was to suggest a new straightforward approach for a systematic examination of chromatographic and signal selectivity in LC-MS-based metabolomics. By calculating the ratio between each feature and its co-eluting features (the co-features), a measurement of the chromatographic selectivity (i.e. extent of co-elution) as well as the signal selectivity (e.g. amount of adduct formation) of each feature could be acquired, the co-feature ratio. This approach was used to examine possible differences in chromatographic and signal selectivity present in samples exposed to three different sample preparation procedures. The capability of the co-feature ratio was evaluated both in a classical targeted setting using isotope labelled standards as well as without standards in an untargeted setting. For the targeted analysis, several metabolites showed a skewed quantitative signal due to poor chromatographic selectivity and/or poor signal selectivity. Moreover, evaluation of the untargeted approach through multivariate analysis of the co-feature ratios demonstrated the possibility to screen for metabolites displaying poor chromatographic and/or signal selectivity characteristics. We conclude that the co-feature ratio can be a useful tool in the development and evaluation of analytical procedures in LC-MS-based metabolomics investigations. Increased selectivity through proper choice of analytical procedures may decrease the false positive and false negative discovery rate and thereby increase the validity of any metabolomic investigation. - Highlights: • The co-feature ratio (CFR) is introduced. • CFR measures chromatographic and signal selectivity of a feature. • CFR can be used for evaluating experimental procedures in metabolomics. • CFR can aid in locating features with poor selectivity.

  4. Your fate is in your hands? Handedness, digit ratio (2D:4D), and selection to a national talent development system.

    Science.gov (United States)

    Baker, Joseph; Kungl, Ann-Marie; Pabst, Jan; Strauß, Bernd; Büsch, Dirk; Schorer, Jörg

    2013-01-01

    Over the past decade a small evidence base has highlighted the potential importance of seemingly innocuous variables related to one's hands, such as hand dominance and the relative length of the second and fourth digits (2D:4D ratio), to success in sport. This study compared 2D:4D digit ratio and handedness among handball players selected to advance in a national talent development system with those not selected. Participants included 480 youth handball players (240 females and 240 males) being considered as part of the talent selection programme for the German Youth National team. Hand dominance and digit ratio were compared to age-matched control data using standard t-tests. There was a greater proportion of left-handers compared to the normal population in males but not in females. There was also a lower digit ratio in both females and males. However, there were no differences between those selected for the next stage of talent development and those not selected on either handedness or digit ratio. These results add support for general effects for both digit ratio and handedness in elite handball; however, these factors seem inadequate to explain talent selection decisions at this level.

  5. Compilation of minimum and maximum isotope ratios of selected elements in naturally occurring terrestrial materials and reagents

    Science.gov (United States)

    Coplen, T.B.; Hopple, J.A.; Böhlke, J.K.; Peiser, H.S.; Rieder, S.E.; Krouse, H.R.; Rosman, K.J.R.; Ding, T.; Vocke, R.D.; Revesz, K.M.; Lamberty, A.; Taylor, P.; De Bievre, P.

    2002-01-01

    Documented variations in the isotopic compositions of some chemical elements are responsible for expanded uncertainties in the standard atomic weights published by the Commission on Atomic Weights and Isotopic Abundances of the International Union of Pure and Applied Chemistry. This report summarizes reported variations in the isotopic compositions of 20 elements that are due to physical and chemical fractionation processes (not due to radioactive decay) and their effects on the standard atomic weight uncertainties. For 11 of those elements (hydrogen, lithium, boron, carbon, nitrogen, oxygen, silicon, sulfur, chlorine, copper, and selenium), standard atomic weight uncertainties have been assigned values that are substantially larger than analytical uncertainties because of common isotope abundance variations in materials of natural terrestrial origin. For 2 elements (chromium and thallium), recently reported isotope abundance variations potentially are large enough to result in future expansion of their atomic weight uncertainties. For 7 elements (magnesium, calcium, iron, zinc, molybdenum, palladium, and tellurium), documented isotope-abundance variations in materials of natural terrestrial origin are too small to have a significant effect on their standard atomic weight uncertainties. This compilation indicates the extent to which the atomic weight of an element in a given material may differ from the standard atomic weight of the element. For most elements given above, data are graphically illustrated by a diagram in which the materials are specified in the ordinate and the compositional ranges are plotted along the abscissa in scales of (1) atomic weight, (2) mole fraction of a selected isotope, and (3) delta value of a selected isotope ratio. There are no internationally distributed isotopic reference materials for the elements zinc, selenium, molybdenum, palladium, and tellurium. Preparation of such materials will help to make isotope ratio measurements among

  6. Multidimensional adaptive testing with a minimum error-variance criterion

    NARCIS (Netherlands)

    van der Linden, Willem J.

    1997-01-01

    The case of adaptive testing under a multidimensional logistic response model is addressed. An adaptive algorithm is proposed that minimizes the (asymptotic) variance of the maximum-likelihood (ML) estimator of a linear combination of abilities of interest. The item selection criterion is a simple

  7. The Bohm criterion for rf discharges

    International Nuclear Information System (INIS)

    Meijer, P.M.; Goedheer, W.J.

    1991-01-01

    The well-known dc Bohm criterion is extended to rf discharges. Both low- (ω rf much-lt ω pi ) and high-(ω pi much-lt ω rf ) frequency regimes are considered. For low frequencies, the dc Bohm criterion holds. This criterion states that the initial energy of the ions entering the sheath must exceed a limit in order to obtain a stable sheath. For high frequencies, a modified limit is derived, which is somewhat lower than that of the dc Bohm criterion. The resulting ion current density in a high-frequency sheath is only a few percent lower than that for the dc case

  8. Plasma sheath criterion in thermal electronegative plasmas

    International Nuclear Information System (INIS)

    Ghomi, Hamid; Khoramabadi, Mansour; Ghorannevis, Mahmod; Shukla, Padma Kant

    2010-01-01

    The sheath formation criterion in electronegative plasma is examined. By using a multifluid model, it is shown that in a collisional sheath there will be upper as well as lower limits for the sheath velocity criterion. However, the parameters of the negative ions only affect the lower limit.

  9. Unitary Evolution as a Uniqueness Criterion

    Science.gov (United States)

    Cortez, J.; Mena Marugán, G. A.; Olmedo, J.; Velhinho, J. M.

    2015-01-01

    It is well known that the process of quantizing field theories is plagued with ambiguities. First, there is ambiguity in the choice of basic variables describing the system. Second, once a choice of field variables has been made, there is ambiguity concerning the selection of a quantum representation of the corresponding canonical commutation relations. The natural strategy to remove these ambiguities is to demand positivity of energy and to invoke symmetries, namely by requiring that classical symmetries become unitarily implemented in the quantum realm. The success of this strategy depends, however, on the existence of a sufficiently large group of symmetries, usually including time-translation invariance. These criteria are therefore generally insufficient in non-stationary situations, as is typical for free fields in curved spacetimes. Recently, the criterion of unitary implementation of the dynamics has been proposed in order to select a unique quantization in the context of manifestly non-stationary systems. Specifically, the unitarity criterion, together with the requirement of invariance under spatial symmetries, has been successfully employed to remove the ambiguities in the quantization of linearly polarized Gowdy models as well as in the quantization of a scalar field with time varying mass, propagating in a static background whose spatial topology is either of a d-sphere (with d = 1, 2, 3) or a three torus. Following Ref. 3, we will see here that the symmetry and unitarity criteria allows for a complete removal of the ambiguities in the quantization of scalar fields propagating in static spacetimes with compact spatial sections, obeying field equations with an explicitly time-dependent mass, of the form ddot φ - Δ φ + s(t)φ = 0 . These results apply in particular to free fields in spacetimes which, like e.g. in the closed FRW models, are conformal to a static spacetime, by means of an exclusively time-dependent conformal factor. In fact, in such

  10. Positive selection of deleterious alleles through interaction with a sex-ratio suppressor gene in African Buffalo: a plausible new mechanism for a high frequency anomaly.

    Directory of Open Access Journals (Sweden)

    Pim van Hooft

    Full Text Available Although generally rare, deleterious alleles can become common through genetic drift, hitchhiking or reductions in selective constraints. Here we present a possible new mechanism that explains the attainment of high frequencies of deleterious alleles in the African buffalo (Syncerus caffer population of Kruger National Park, through positive selection of these alleles that is ultimately driven by a sex-ratio suppressor. We have previously shown that one in four Kruger buffalo has a Y-chromosome profile that, despite being associated with low body condition, appears to impart a relative reproductive advantage, and which is stably maintained through a sex-ratio suppressor. Apparently, this sex-ratio suppressor prevents fertility reduction that generally accompanies sex-ratio distortion. We hypothesize that this body-condition-associated reproductive advantage increases the fitness of alleles that negatively affect male body condition, causing genome-wide positive selection of these alleles. To investigate this we genotyped 459 buffalo using 17 autosomal microsatellites. By correlating heterozygosity with body condition (heterozygosity-fitness correlations, we found that most microsatellites were associated with one of two gene types: one with elevated frequencies of deleterious alleles that have a negative effect on body condition, irrespective of sex; the other with elevated frequencies of sexually antagonistic alleles that are negative for male body condition but positive for female body condition. Positive selection and a direct association with a Y-chromosomal sex-ratio suppressor are indicated, respectively, by allele clines and by relatively high numbers of homozygous deleterious alleles among sex-ratio suppressor carriers. This study, which employs novel statistical techniques to analyse heterozygosity-fitness correlations, is the first to demonstrate the abundance of sexually-antagonistic genes in a natural mammal population. It also has

  11. An ethical criterion for geoscientists

    Science.gov (United States)

    Peppoloni, Silvia

    2013-04-01

    Anthropological researches have demonstrated that at some point in human history, man makes an evolutive jump in cultural sense: at first, he is able to perceive himself only as part of a community, later he becomes able to perceive himself as an individual. The analysis of the linguistic roots of the word "Ethics" discloses the traces of this evolutive transition and an original double meaning: on the one hand, "Ethics" contains a sense of belonging to the social fabric, on the other hand, it is related to the individual sphere. These two existential conditions (social and individual) unexpectedly co-exist in the word "Ethics". So, "Geo-Ethics" can be defined as the investigation and reflection on those values upon which to base appropriate behaviours and practices regarding the Geosphere (social dimension), but also as the analysis of the relationships between the geoscientist who acts and his own actions (individual dimension). Therefore, the meaning of the word "Geo-Ethics" calls upon geoscientists to face the responsibility of an ethical behaviour. What does this responsibility consist of and what motivations are necessary to push geoscientists to practice the Earth sciences in an ethical way? An ethical commitment exists if there is research of truth. In their activities, Geoscientists should be searchers and defenders of truth. If geoscientists give up this role, they completely empty of meaning their work. Ethical obligations arise from the possession of specific knowledge that has practical consequences. Geoscientists, as active and responsible part of society, have to serve society and the common good. The ethical criterion for a geoscientist should be rooted in his individual sphere, that is the source of any action even in the social sphere, and should have the intellectual honesty as main requirement. It includes: • respect for the truth that they look for and for other's ideas; • recognition of the value of others as valuable for themselves;

  12. The qualitative criterion of transient angle stability

    DEFF Research Database (Denmark)

    Lyu, R.; Xue, Y.; Xue, F.

    2015-01-01

    In almost all the literatures, the qualitative assessment of transient angle stability extracts the angle information of generators based on the swing curve. As the angle (or angle difference) of concern and the threshold value rely strongly on the engineering experience, the validity and robust...... of these criterions are weak. Based on the stability mechanism from the extended equal area criterion (EEAC) theory and combining with abundant simulations of real system, this paper analyzes the criterions in most literatures and finds that the results could be too conservative or too optimistic. It is concluded...

  13. A work criterion for plastic collapse

    International Nuclear Information System (INIS)

    Muscat, Martin; Mackenzie, Donald; Hamilton, Robert

    2003-01-01

    A new criterion for evaluating limit and plastic loads in pressure vessel design by analysis is presented. The proposed criterion is based on the plastic work dissipated in the structure as loading progresses and may be used for structures subject to a single load or a combination of multiple loads. Example analyses show that limit and plastic loads given by the plastic work criterion are robust and consistent. The limit and plastic loads are determined purely by the inelastic response of the structure and are not influenced by the initial elastic response: a problem with some established plastic criteria

  14. A convenient accuracy criterion for time domain FE-calculations

    DEFF Research Database (Denmark)

    Jensen, Morten Skaarup

    1997-01-01

    An accuracy criterion that is well suited to tome domain finite element (FE) calculations is presented. It is then used to develop a method for selecting time steps and element meshes that produce accurate results without significantly overburderning the computer. Use of this method is illustrated...... with a simple example, where comparison with an analytical solution shows that results are sufficiently accurate, which is not always the case with more primitive mthods for determining the discretisation....

  15. Bayesian estimation of direct and correlated responses to selection on linear or ratio expressions of feed efficiency in pigs

    DEFF Research Database (Denmark)

    Shirali, Mahmoud; Varley, Patrick Francis; Jensen, Just

    2018-01-01

    meat percentage (LMP) along with the derived traits of RFI and FCR; and (3) deriving Bayesian estimates of direct and correlated responses to selection on RFI, FCR, ADG, ADFI, and LMP. Response to selection was defined as the difference in additive genetic mean of the selected top individuals, expected......, respectively. Selection against RFIG showed a direct response of − 0.16 kg/d and correlated responses of − 0.16 kg/kg for FCR and − 0.15 kg/d for ADFI, with no effect on other production traits. Selection against FCR resulted in a direct response of − 0.17 kg/kg and correlated responses of − 0.14 kg/d for RFIG......, − 0.18 kg/d for ADFI, and 0.98% for LMP. Conclusions: The Bayesian methodology developed here enables prediction of breeding values for FCR and RFI from a single multi-variate model. In addition, we derived posterior distributions of direct and correlated responses to selection. Genetic parameter...

  16. Focused information criterion and model averaging based on weighted composite quantile regression

    KAUST Repository

    Xu, Ganggang; Wang, Suojin; Huang, Jianhua Z.

    2013-01-01

    We study the focused information criterion and frequentist model averaging and their application to post-model-selection inference for weighted composite quantile regression (WCQR) in the context of the additive partial linear models. With the non

  17. A framework for analyzing sex-selective abortion: the example of changing sex ratios in Southern Caucasus

    Science.gov (United States)

    Hohmann, Sophie A; Lefèvre, Cécile A; Garenne, Michel L

    2014-01-01

    The paper proposes a socioeconomic framework of supply, demand, and regulation to explain the development of sex-selective abortion in several parts of the world. The framework is then applied to three countries of southern Caucasus (Armenia, Azerbaijan, and Georgia) where sex-selective abortion has developed since the collapse of the Soviet Union. The authors argue that sex-selective abortion cannot be explained simply by patriarchal social systems, sex discrimination, or son preference. The emphasis is put on the long-term acceptability of abortion in the region, on acceptability of sex-screening by both the medical establishment and by the population, on newly imported techniques of sex-screening, and on the changing demand for children associated with the major economic and social changes that followed the dismantlement of the Soviet Union. PMID:25349481

  18. L X-ray intensity ratio measurements using selective L sub-shell photo-ionisation on synchrotron

    Science.gov (United States)

    Bansal, Himani; Tiwari, M. K.; Mittal, Raj

    2017-10-01

    Lα/Lℓ, Lβ /Lℓ and Lγ/Lℓ intensity ratios have been measured for elements in the range 66≤Z≤83 at tuned photon energies on synchrotron beam line-16 at Indus-2, India. For each element, three incident energies Ei were E3; EL3 EL1 where ELi are Li absorption edge energies of the element. Emitted L X-ray spectrum of an element constitutes a number of X-ray lines generally grouped into four main groups due to limited resolution of available detectors as Lℓ(L3-M1), Lα(L3-M4,5), Lβ(L1-M2,3,4,5,N4; L2-M3,4; L3-N1,4,5,O1,4,5) and Lγ(L2-N1,4,O1,4; L1-N2,3,5,O3,2). Lα and Lℓ both comprise only the lines feeding L3 level and Lβ group comprises X-ray lines feeding all the three sub-shells where as Lγ involves contribution from L1 and L2 feedings. Only E3 excitation gives the ratios free from intra sub-shell Coster-Kronig (CK) transitions while excitations E2 and E1 give CK affected Lβ/Lℓ and Lγ/Lℓ X-ray intensity ratios and Lα/Lℓ still remains free from CKs. The pattern of intensity ratios at three excitation energies of elements was well interpreted in terms of on/off of CK transitions (Bambynek et al., 1972; Campbell, 2003) and outer shell electron filling configuration (Scofield, 1973).

  19. Joined application of a multiaxial critical plane criterion and a strain energy density criterion in low-cycle fatigue

    Directory of Open Access Journals (Sweden)

    Andrea Carpinteri

    2017-07-01

    Full Text Available In the present paper, the multiaxial fatigue life assessment of notched structural components is performed by employing a strain-based multiaxial fatigue criterion. Such a criterion, depending on the critical plane concept, is extended by implementing the control volume concept reated to the Strain Energy Density (SED approach: a material point located at a certain distance from the notch tip is assumed to be the verification point where to perform the above assessment. Such a distance, measured along the notch bisector, is a function of both the biaxiality ratio (defined as the ratio between the applied shear stress amplitude and the normal stress amplitude and the control volume radii under Mode I and Mode III. Once the position of the verification point is determined, the fatigue lifetime is assessed through an equivalent strain amplitude, acting on the critical plane, together with a unique material reference curve (i.e. the Manson-Coffin curve. Some uniaxial and multiaxial fatigue data related to V-notched round bars made of titanium grade 5 alloy (Ti-6Al-4V are examined to validate the present criterion.

  20. The stressor criterion for posttraumatic stress disorder: Does it matter?

    Science.gov (United States)

    Roberts, Andrea L.; Dohrenwend, Bruce P.; Aiello, Allison; Wright, Rosalind J.; Maercker, Andreas; Galea, Sandro; Koenen, Karestan C.

    2013-01-01

    Objective The definition of the stressor criterion for posttraumatic stress disorder (“Criterion A1”) is hotly debated with major revisions being considered for DSM-V. We examine whether symptoms, course, and consequences of PTSD vary predictably with the type of stressful event that precipitates symptoms. Method We used data from the 2009 PTSD diagnostic subsample (N=3,013) of the Nurses Health Study II. We asked respondents about exposure to stressful events qualifying under 1) DSM-III, 2) DSM-IV, or 3) not qualifying under DSM Criterion A1. Respondents selected the event they considered worst and reported subsequent PTSD symptoms. Among participants who met all other DSM-IV PTSD criteria, we compared distress, symptom severity, duration, impairment, receipt of professional help, and nine physical, behavioral, and psychiatric sequelae (e.g. physical functioning, unemployment, depression) by precipitating event group. Various assessment tools were used to determine fulfillment of PTSD Criteria B through F and to assess these 14 outcomes. Results Participants with PTSD from DSM-III events reported on average 1 more symptom (DSM-III mean=11.8 symptoms, DSM-IV=10.7, non-DSM=10.9) and more often reported symptoms lasted one year or longer compared to participants with PTSD from other groups. However, sequelae of PTSD did not vary systematically with precipitating event type. Conclusions Results indicate the stressor criterion as defined by the DSM may not be informative in characterizing PTSD symptoms and sequelae. In the context of ongoing DSM-V revision, these results suggest that Criterion A1 could be expanded in DSM-V without much consequence for our understanding of PTSD phenomenology. Events not considered qualifying stressors under the DSM produced PTSD as consequential as PTSD following DSM-III events, suggesting PTSD may be an aberrantly severe but nonspecific stress response syndrome. PMID:22401487

  1. Effect of the Phase Volume Ratio on the Potential of a Liquid-Membrane Ion-Selective Electrode

    Czech Academy of Sciences Publication Activity Database

    Samec, Zdeněk; Girault, H. H.

    2004-01-01

    Roč. 76, č. 14 (2004), s. 4150-4155 ISSN 0003-2700 R&D Projects: GA MŠk ME 502 Institutional research plan: CEZ:AV0Z4040901 Keywords : liquit-membrane * ion-selective electrode * two.phase liquid system Subject RIV: CG - Electrochemistry Impact factor: 5.450, year: 2004

  2. Sensor Calibration Design Based on D-Optimality Criterion

    Directory of Open Access Journals (Sweden)

    Hajiyev Chingiz

    2016-09-01

    Full Text Available In this study, a procedure for optimal selection of measurement points using the D-optimality criterion to find the best calibration curves of measurement sensors is proposed. The coefficients of calibration curve are evaluated by applying the classical Least Squares Method (LSM. As an example, the problem of optimal selection for standard pressure setters when calibrating a differential pressure sensor is solved. The values obtained from the D-optimum measurement points for calibration of the differential pressure sensor are compared with those from actual experiments. Comparison of the calibration errors corresponding to the D-optimal, A-optimal and Equidistant calibration curves is done.

  3. Enrichment ratios of elements in selected plant species from black coal mine dumps in Lower Silesia (Poland)

    Energy Technology Data Exchange (ETDEWEB)

    Samecka-Cymerman, A.; Kempers, A.J. [University of Wroclaw, Wroclaw (Poland)

    2003-07-01

    Concentration of the metals Al, Ba, Cd, Co, Cr, Cu, Mn, Ni, Pb, Sr, Zn and V as well as N, P, K, Ca, Mg, Fe and S were measured in soils and in two tree species (leaves of Betula pendula and Salix caprea) and two herbs (whole above-ground parts of Solidago canadensis and Tanacetum vulgare) sampled from dumps in the Walbrzych coal mine area (Lower Silesia, SW Poland). These plants, as used to evaluate the distribution of elements in the examined dumps, contained elevated levels of Cd, Co, Cu, Mn, Ni, Pb and Zn. Especially the highest levels of Mn in Betula pendula seriously exceed background values. Betula pendula characterized also the highest enrichment ratio for Mn, Salix caprea for Ni and Sr and Tanacetum vulgare for Cu. Test-t indicated that from both herbs Tanace-tum vulgare accumulated much more K, N, S and Zn than Solidago canadensis and of both trees Salix caprea accumulated significantly more Cd, Cu, K and Ca than Betula pendula, while this last species accumulated significantly more Fe and Mn than Salix caprea. A post hoc LSD test indicated that all examined plants had similar enrichment ratios for Al, Pb and V.

  4. Selection of mode for the measurement of lead isotope ratios by inductively coupled plasma mass spectrometry and its application to milk powder analysis

    International Nuclear Information System (INIS)

    Dean, J.R.; Ebdon, L.; Massey, R.

    1987-01-01

    An investigation into the selection of the optimum mode for the measurement of isotope ratios in inductively coupled plasma mass spectrometry (ICP-MS) is reported, with particular reference to lead isotope ratios. Variation in the accuracy and precision achievable using the measurement modes of scanning and peak jumping are discussed. It is concluded that if sufficient sample and time are available, scanning gives best accuracy and precision. Isotope dilution analysis (IDA) has been applied to the measurement of the lead content of two dried milk powders of Australian and European origin introduced as slurries into ICP-MS. Differences in the lead isotope ratios in the two milk powders were investigated and the total lead content determined by IDA. Isotope dilution analysis permitted accurate data to be obtained with an RSD of 4.2% or milk powder containing less than 30 ng g -1 of lead. The ICP-MS technique is confirmed as a useful tool for IDA. (author)

  5. Predicting speech intelligibility based on the signal-to-noise envelope power ratio after modulation-frequency selective processing

    DEFF Research Database (Denmark)

    Jørgensen, Søren; Dau, Torsten

    2011-01-01

    A model for predicting the intelligibility of processed noisy speech is proposed. The speech-based envelope power spectrum model has a similar structure as the model of Ewert and Dau [(2000). J. Acoust. Soc. Am. 108, 1181-1196], developed to account for modulation detection and masking data. The ...... process provides a key measure of speech intelligibility. © 2011 Acoustical Society of America.......A model for predicting the intelligibility of processed noisy speech is proposed. The speech-based envelope power spectrum model has a similar structure as the model of Ewert and Dau [(2000). J. Acoust. Soc. Am. 108, 1181-1196], developed to account for modulation detection and masking data....... The model estimates the speech-to-noise envelope power ratio, SNR env, at the output of a modulation filterbank and relates this metric to speech intelligibility using the concept of an ideal observer. Predictions were compared to data on the intelligibility of speech presented in stationary speech...

  6. The EMU debt criterion: an interpretation

    Directory of Open Access Journals (Sweden)

    R. BERNDSEN

    1997-12-01

    Full Text Available The convergence criteria specified in the Maastricht Treaty on government deficit and debt, inflation, the exchange rate and the long-term interest rate will play an important, if not decisive, role in determining which countries move on to the third stage of the Economic and Monetary Union (EMU. The aim of this work is to provide a possible interpretation of the EMU debt criterion. The author investigates the government debt criterion which, as Article 104c(2b of the Treaty shows, has a considerable scope for interpretation. Although this subject has been discussed extensively, relatively little work has been done to develop a clear interpretation of the EMU debt criterion. A flexible approach is adopted in which parts of the relevant Treaty text are characterised using two parameters.

  7. FFTBM and primary pressure acceptance criterion

    International Nuclear Information System (INIS)

    Prosek, A.

    2004-01-01

    When thermalhydraulic computer codes are used for simulation in the area of nuclear engineering the question is how to conduct an objective comparison between the code calculation and measured data. To answer this the fast Fourier transform based method (FFTBM) was developed. When the FFTBM method was developed the acceptance criteria for primary pressure and total accuracy were set. In the recent study the FFTBM method was used for accuracy quantification of RD-14M large LOCA test B9401 calculations. The blind accuracy analysis indicated good total accuracy while the primary pressure criterion was not fulfilled. The objective of the study was therefore to investigate the reasons for not fulfilling the primary pressure acceptance criterion and the applicability of the criterion to experimental facilities simulating heavy water reactor. The results of the open quantitative analysis showed that sensitivity analysis for influence parameters provide sufficient information to judge in which calculation the accuracy of primary pressure is acceptable. (author)

  8. Effect of arginine:lysine and glycine:methionine intake ratios on dyslipidemia and selected biomarkers implicated in cardiovascular disease: A study with hypercholesterolemic rats.

    Science.gov (United States)

    Venkatesh, Ravula; Srinivasan, Krishnapura; Singh, Sridevi Annapurna

    2017-07-01

    The effect of intake ratios of arginine (Arg): lysine (Lys) and glycine (Gly): methionine (Met) on lipid profile and selected cardiovascular disease markers, was studied, in rats maintained on a hypercholesterolemic diet. The rise in blood cholesterol was countered by 32%, 24%, and 49%, respectively, through increased oral supplementation of Arg, Gly, and Arg+Gly; a corresponding increase in plasma phospholipids at the end of the 8-week study was observed. The elevated plasma cholesterol to phospholipids ratio was countered by 27, 40, and 57%, respectively, through oral supplementation of Arg, Gly, and Arg+Gly. The elevation in hepatic cholesterol was lowered by 18, 29, and 51%, respectively, while phospholipids concentration was concomitantly increased by these amino acids. The elevated cholesterol to phospholipids ratio was, thus, significantly countered in the hypercholesterolemic situation by orally supplemented Arg, Gly, and Arg+Gly. Increased plasma asymmetric dimethylarginine (ADMA) levels, under hypercholesterolemic conditions, were lowered by 12, 15 and 34%, respectively, while plasma symmetric dimethylarginine (SDMA) levels were lowered by 14, 10 and 17%, respectively, with orally supplemented Arg, Gly and Arg+Gly. Only Gly and Arg+Gly decreased plasma homocysteine levels. Total nitric oxide (NO) concentration was considerably increased by Gly supplementation in hypercholesterolemic rats. Thus, altered ratios of Arg:Lys or Gly:Met offered beneficial influence on the lipid profile and plasma levels of ADMA, SDMA and homocysteine in hypercholesterolemic rats. Optimal beneficial effects, among ratios tested, was observed when Arg:Lys and Gly:Met ratios were maintained in ratios of 1:1 and 2:1, respectively. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  9. Acute effects of caffeine on threat-selective attention: moderation by anxiety and EEG theta/beta ratio.

    Science.gov (United States)

    van Son, Dana; Schalbroeck, Rik; Angelidis, Angelos; van der Wee, Nic J A; van der Does, Willem; Putman, Peter

    2018-05-21

    Spontaneous EEG theta/beta ratio (TBR) probably marks prefrontal cortical (PFC) executive control, and its regulation of attentional threat-bias. Caffeine at moderate doses may strengthen executive control through increased PFC catecholamine action, dependent on basal PFC function. To test if caffeine affects threat-bias, moderated by baseline frontal TBR and trait-anxiety. A pictorial emotional Stroop task was used to assess threat-bias in forty female participants in a cross-over, double-blind study after placebo and 200 mg caffeine. At baseline and after placebo, comparable relations were observed for negative pictures: high TBR was related to low threat-bias in low trait-anxious people. Caffeine had opposite effects on threat-bias in low trait-anxious people with low and high TBR. This further supports TBR as a marker of executive control and highlights the importance of taking baseline executive function into consideration when studying effects of caffeine on executive functions. Copyright © 2018 Elsevier B.V. All rights reserved.

  10. General stability criterion for inviscid parallel flow

    International Nuclear Information System (INIS)

    Sun Liang

    2007-01-01

    Arnol'd's second stability theorem is approached from an elementary point of view. First, a sufficient criterion for stability is found analytically as either -μ 1 s ) s ) in the flow, where U s is the velocity at the inflection point, and μ 1 is the eigenvalue of Poincare's problem. Second, this criterion is generalized to barotropic geophysical flows in the β plane. And the connections between present criteria and Arnol'd's nonlinear criteria are also discussed. The proofs are completely elementary and so could be used to teach undergraduate students

  11. Sampling Criterion for EMC Near Field Measurements

    DEFF Research Database (Denmark)

    Franek, Ondrej; Sørensen, Morten; Ebert, Hans

    2012-01-01

    An alternative, quasi-empirical sampling criterion for EMC near field measurements intended for close coupling investigations is proposed. The criterion is based on maximum error caused by sub-optimal sampling of near fields in the vicinity of an elementary dipole, which is suggested as a worst......-case representative of a signal trace on a typical printed circuit board. It has been found that the sampling density derived in this way is in fact very similar to that given by the antenna near field sampling theorem, if an error less than 1 dB is required. The principal advantage of the proposed formulation is its...

  12. Sex ratios in the most-selective elite US undergraduate colleges and universities are consistent with the hypothesis that modern educational systems increasingly select for conscientious personality compared with intelligence.

    Science.gov (United States)

    Charlton, Bruce G

    2009-08-01

    The main predictors of examination results and educational achievement in modern societies are intelligence (IQ - or general factor 'g' intelligence) and the personality trait termed 'Conscientiousness' (C). I have previously argued that increased use of continuous assessment (e.g. course work rather than timed and supervised examinations) and increased duration of the educational process implies that modern educational systems have become increasingly selective for the personality trait of Conscientiousness and consequently less selective for IQ. I have tested this prediction (in a preliminary fashion) by looking at the sex ratios in the most selective elite US universities. My two main assumptions are: (1) that a greater proportion of individuals with very high intelligence are men than women, and (2) that women are more conscientious than men. To estimate the proportion of men and women expected at highly-selective schools, I performed demonstration calculations based on three plausible estimates of male and female IQ averages and standard deviations. The expected percentage of men at elite undergraduate colleges (selecting students with IQ above 130 - i.e. in the top 2% of the population) were 66%, 61% and 74%. When these estimates were compared with the sex ratios at 33 elite colleges and universities, only two technical institutes had more than 60% men. Elite US colleges and universities therefore seem to be selecting primarily on the basis of something other than IQ - probably conscientiousness. There is a 'missing population' of very high IQ men who are not being admitted to the most selective and prestigious undergraduate schools, probably because their high school educational qualifications and evaluations are too low. This analysis is therefore consistent with the hypothesis that modern educational systems tend to select more strongly for Conscientiousness than for IQ. The implication is that modern undergraduates at the most-selective US schools are not

  13. Tile-based Fisher-ratio software for improved feature selection analysis of comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry data.

    Science.gov (United States)

    Marney, Luke C; Siegler, W Christopher; Parsons, Brendon A; Hoggard, Jamin C; Wright, Bob W; Synovec, Robert E

    2013-10-15

    Comprehensive two-dimensional (2D) gas chromatography coupled with time-of-flight mass spectrometry (GC × GC-TOFMS) is a highly capable instrumental platform that produces complex and information-rich multi-dimensional chemical data. The data can be initially overwhelming, especially when many samples (of various sample classes) are analyzed with multiple injections for each sample. Thus, the data must be analyzed in such a way as to extract the most meaningful information. The pixel-based and peak table-based Fisher ratio algorithmic approaches have been used successfully in the past to reduce the multi-dimensional data down to those chemical compounds that are changing between the sample classes relative to those that are not changing (i.e., chemical feature selection). We report on the initial development of a computationally fast novel tile-based Fisher-ratio software that addresses the challenges due to 2D retention time misalignment without explicitly aligning the data, which is often a shortcoming for both pixel-based and peak table-based algorithmic approaches. Concurrently, the tile-based Fisher-ratio algorithm significantly improves the sensitivity contrast of true positives against a background of potential false positives and noise. In this study, eight compounds, plus one internal standard, were spiked into diesel at various concentrations. The tile-based F-ratio algorithmic approach was able to "discover" all spiked analytes, within the complex diesel sample matrix with thousands of potential false positives, in each possible concentration comparison, even at the lowest absolute spiked analyte concentration ratio of 1.06, the ratio between the concentrations in the spiked diesel sample to the native concentration in diesel. Copyright © 2013 Elsevier B.V. All rights reserved.

  14. A pellet-clad interaction failure criterion

    International Nuclear Information System (INIS)

    Howl, D.A.; Coucill, D.N.; Marechal, A.J.C.

    1983-01-01

    A Pellet-Clad Interaction (PCI) failure criterion, enabling the number of fuel rod failures in a reactor core to be determined for a variety of normal and fault conditions, is required for safety analysis. The criterion currently being used for the safety analysis of the Pressurized Water Reactor planned for Sizewell in the UK is defined and justified in this paper. The criterion is based upon a threshold clad stress which diminishes with increasing fast neutron dose. This concept is consistent with the mechanism of clad failure being stress corrosion cracking (SCC); providing excess corrodant is always present, the dominant parameter determining the propagation of SCC defects is stress. In applying the criterion, the SLEUTH-SEER 77 fuel performance computer code is used to calculate the peak clad stress, allowing for concentrations due to pellet hourglassing and the effect of radial cracks in the fuel. The method has been validated by analysis of PCI failures in various in-reactor experiments, particularly in the well-characterised power ramp tests in the Steam Generating Heavy Water Reactor (SGHWR) at Winfrith. It is also in accord with out-of-reactor tests with iodine and irradiated Zircaloy clad, such as those carried out at Kjeller in Norway. (author)

  15. The Leadership Criterion in Technological Institute

    International Nuclear Information System (INIS)

    Carvalho, Marcelo Souza de; Cussa, Adriana Lourenco d'Avila; Suita, Julio Cezar

    2005-01-01

    This paper introduces the Direction's 'Decision Making Practice'. It has recently been reviewed with the merging of the beddings of the Leadership Criterion (CE-PNQ). These changes improved the control of institutional plans of action which are the result of the global performance critical analysis and other information associated with the Decision Making Practice. (author)

  16. Mercier criterion for high-β tokamaks

    International Nuclear Information System (INIS)

    Galvao, R.M.O.

    1984-01-01

    An expression, for the application of the Mercier criterion to numerical studies of diffuse high-β tokamaks (β approximatelly Σ,q approximatelly 1), which contains only leading order contributions in the high-β tokamak approximation is derived. (L.C.) [pt

  17. Information criterion for the categorization quality evaluation

    Directory of Open Access Journals (Sweden)

    Michail V. Svirkin

    2011-05-01

    Full Text Available The paper considers the possibility of using the variation of information function as a quality criterion for categorizing a collection of documents. The performance of the variation of information function is being examined subject to the number of categories and the sample volume of the test document collection.

  18. A scale invariance criterion for LES parametrizations

    Directory of Open Access Journals (Sweden)

    Urs Schaefer-Rolffs

    2015-01-01

    Full Text Available Turbulent kinetic energy cascades in fluid dynamical systems are usually characterized by scale invariance. However, representations of subgrid scales in large eddy simulations do not necessarily fulfill this constraint. So far, scale invariance has been considered in the context of isotropic, incompressible, and three-dimensional turbulence. In the present paper, the theory is extended to compressible flows that obey the hydrostatic approximation, as well as to corresponding subgrid-scale parametrizations. A criterion is presented to check if the symmetries of the governing equations are correctly translated into the equations used in numerical models. By applying scaling transformations to the model equations, relations between the scaling factors are obtained by demanding that the mathematical structure of the equations does not change.The criterion is validated by recovering the breakdown of scale invariance in the classical Smagorinsky model and confirming scale invariance for the Dynamic Smagorinsky Model. The criterion also shows that the compressible continuity equation is intrinsically scale-invariant. The criterion also proves that a scale-invariant turbulent kinetic energy equation or a scale-invariant equation of motion for a passive tracer is obtained only with a dynamic mixing length. For large-scale atmospheric flows governed by the hydrostatic balance the energy cascade is due to horizontal advection and the vertical length scale exhibits a scaling behaviour that is different from that derived for horizontal length scales.

  19. Impact of P/In flux ratio and epilayer thickness on faceting for nanoscale selective area growth of InP by molecular beam epitaxy.

    Science.gov (United States)

    Fahed, M; Desplanque, L; Coinon, C; Troadec, D; Wallart, X

    2015-07-24

    The impact of the P/In flux ratio and the deposited thickness on the faceting of InP nanostructures selectively grown by molecular beam epitaxy (MBE) is reported. Homoepitaxial growth of InP is performed inside 200 nm wide stripe openings oriented either along a [110] or [1-10] azimuth in a 10 nm thick SiO2 film deposited on an InP(001) substrate. When varying the P/In flux ratio, no major shape differences are observed for [1-10]-oriented apertures. On the other hand, the InP nanostructure cross sections strongly evolve for [110]-oriented apertures for which (111)B facets are more prominent and (001) ones shrink for large P/In flux ratio values. These results show that the growth conditions allow tailoring the nanocrystal shape. They are discussed in the framework of the equilibrium crystal shape model using existing theoretical calculations of the surface energies of different low-index InP surfaces as a function of the phosphorus chemical potential, directly related to the P/In ratio. Experimental observations strongly suggest that the relative (111)A surface energy is probably smaller than the calculated value. We also discuss the evolution of the nanostructure shape with the InP-deposited thickness.

  20. Development of a site-specific water quality criterion for hexavalent chromium

    International Nuclear Information System (INIS)

    McIntyre, D.O.; Sticko, J.P.; Reash, R.J.

    1995-01-01

    The effluent of treated fly ash from a coal-fired power plant located on the Ohio River periodically exceeds its NPDES acute permit limit for hexavalent chromium of 15 microg/L. The increased levels of hexavalent chromium in the effluent are a recent occurrence which are likely due to changes in coal blends burned in the generating units. Ohio EPA determined the use designation of the receiving stream (Limited Resource Water) was being attained and a one-year biomonitoring program of the effluent detected no acute toxicity to Ceriodaphnia dubia or Daphnia magna. The water-effect ratio (WER) procedure was selected to develop a site-specific criterion maximum concentration for hexavalent chromium for the effluent's receiving stream. WER procedures followed those described in EPA's ''Interim Guidance on Determination and Use of Water-Effect Ratios for Metals'' (1994). Site water used in the WER determinations was undiluted effluent since the receiving stream originates at the discharge point of the outfall. 48-hour acute D. magna and 96-hour acute fathead minnow toxicity tests were selected as the primary and secondary tests, respectively for use in three seasonal WER determinations. The results of the three WER determinations and the status of the regulatory process will be presented

  1. Procedures for the selection of stopping power ratios for electron beams: Comparison of IAEA TRS procedures and of DIN procedures with Monte Carlo results

    International Nuclear Information System (INIS)

    Roos, M.; Christ, G.

    2000-01-01

    In the International Code of Practice IAEA TRS-381 the stopping power ratios water/air are selected according to the half-value depth and the depth of measurement. In the German Standard DIN 6800-2 a different procedure is recommended, which, in addition, takes the practical electron range into account; the stopping power data for monoenergetic beams from IAEA TRS-381 are used. Both procedures are compared with recent Monte Carlo calculations carried out for various beams of clinical accelerators. It is found that the DIN procedure shows a slightly better agreement. In addition, the stopping power ratios in IAEA TRS-381 are compared with those in DIN 6800-2 for the reference conditions of the beams from the PTB linac; the maximum deviation is not larger than 0.6%. (author)

  2. Determination of the ratio between phosphorus and uranium in surface waters selected in the State of Mexico

    International Nuclear Information System (INIS)

    Ordonez R, E.

    2001-01-01

    The agricultural regions lately, they have suffered a severe contamination for the big ones quantities of chemical fertilizers and of pesticides applied to improve their production and quality, increasing these in areas with temperatures but you lower that the average. For the importance of the physicochemical processes that they are made in the waters to settle down surface near to agricultural fields, the physicochemical characteristics were analysed of these waters to determine the contributions that they carry out the phosphate fertilizers that are carried by the escorrentia toward the borders and to make a pursuit of their variability during an agricultural cycle, in times of the summertime and of rains, as well as to observe the effect of the depth in these physicochemical properties. Its were sampling three borders and a spring that it served of white, all them located in the suburbs of the Xinantecatl (Nevado de Toluca), municipality of Zinacantepec, State of Mexico, area with the temperatures but drops registered in the region. They were carried out samplings in the first days of the months of April, July and November. The points of those sampled borders were the influent, the effluent and 3 different depths (lm, 3m and 5m). where was not possible sampling all the points, its were sampling only the one influent and the effluent. The selected physicochemical parameters were the temperature, the pH, the conductivity electric and the one oxygenates dissolved This determination in situ you carries out with a team portable of type Check-Mate, of interchangeable electrodes. The certain anions they were phosphates, nitrates, sulfates and bicarbonates; the measurement of the concentration of anions, one carries out for ultraviolet-visible light spectroscopy and titration. The cations analysed they were sodium, potassium, iron, calcium and magnesium. The cations concentration was determined by atomic absorption spectroscopy. The determination of the uranium

  3. Criterion learning in rule-based categorization: simulation of neural mechanism and new data.

    Science.gov (United States)

    Helie, Sebastien; Ell, Shawn W; Filoteo, J Vincent; Maddox, W Todd

    2015-04-01

    In perceptual categorization, rule selection consists of selecting one or several stimulus-dimensions to be used to categorize the stimuli (e.g., categorize lines according to their length). Once a rule has been selected, criterion learning consists of defining how stimuli will be grouped using the selected dimension(s) (e.g., if the selected rule is line length, define 'long' and 'short'). Very little is known about the neuroscience of criterion learning, and most existing computational models do not provide a biological mechanism for this process. In this article, we introduce a new model of rule learning called Heterosynaptic Inhibitory Criterion Learning (HICL). HICL includes a biologically-based explanation of criterion learning, and we use new category-learning data to test key aspects of the model. In HICL, rule selective cells in prefrontal cortex modulate stimulus-response associations using pre-synaptic inhibition. Criterion learning is implemented by a new type of heterosynaptic error-driven Hebbian learning at inhibitory synapses that uses feedback to drive cell activation above/below thresholds representing ionic gating mechanisms. The model is used to account for new human categorization data from two experiments showing that: (1) changing rule criterion on a given dimension is easier if irrelevant dimensions are also changing (Experiment 1), and (2) showing that changing the relevant rule dimension and learning a new criterion is more difficult, but also facilitated by a change in the irrelevant dimension (Experiment 2). We conclude with a discussion of some of HICL's implications for future research on rule learning. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Selection of criterions of fuels incineration on heat power plants

    International Nuclear Information System (INIS)

    Bubnov, V.P.; Minchenko, E.M.; Zelenukho, E.V.

    2006-01-01

    Fuel and energy complex takes first place in industry field of cities and defines in many respects environmental situation of cities. The products of combustion of fuel bring the greatest contribution in environmental contamination. This factor is ignored during calculation of technical and economics indexes. Ecological impact of heat power plants on the environment is determined separately from assessment of ecological damage. Determination of optimal conditions of functioning of heat power plants incineration with respect to technical, economics and ecological indexes with use of multicriterion mathematics model is proposed. (authors)

  5. Electron accelerators for radiation processing: Criterions of selection and exploitation

    International Nuclear Information System (INIS)

    Zimek, Zbigniew

    2001-01-01

    The progress in accelerator technology is tightly attached to the continuously advanced development in many branches of technical activity. Although the present level of accelerators development can satisfy most of the commercial requirements, this field continues to expand and improve quality by offering efficient, cheap, reliable, high average beam power commercial units. Accelerator construction must be a compromised between size, efficiency and cost with respect to the field of its application. High power accelerators have been developed to meet specific demands of flue gas treatment and other high throughput to increase the capacity of the progress and reduced unit cost of operation. Automatic control, reliability and reduced maintenance, adequate adoption to process conditions, suitable electron energy and beam power are the basic features of modern accelerator construction. Accelerators have the potential to serve as industrial radiation sources and eventually may replace the isotope sources in future. Electron beam plants can transfer much higher amounts of energy into the irradiated objects than other types of facilities including gamma plants. This provides the opportunity to construct technological lines with high capacity that are more technically and economically suitable with high throughputs, short evidence time and grate versatility

  6. Selective dopamine D3 receptor antagonism by SB-277011A attenuates cocaine reinforcement as assessed by progressive-ratio and variable-cost–variable-payoff fixed-ratio cocaine self-administration in rats

    Science.gov (United States)

    Xi, Zheng-Xiong; Gilbert, Jeremy G.; Pak, Arlene C.; Ashby, Charles R.; Heidbreder, Christian A.; Gardner, Eliot L.

    2013-01-01

    In rats, acute administration of SB-277011A, a highly selective dopamine (DA) D3 receptor antagonist, blocks cocaine-enhanced brain stimulation reward, cocaine-seeking behaviour and reinstatement of cocaine-seeking behaviour. Here, we investigated whether SB-277011A attenuates cocaine reinforcement as assessed by cocaine self-administration under variable-cost–variable-payoff fixed-ratio (FR) and progressive-ratio (PR) reinforcement schedules. Acute i.p. administration of SB-277011A (3–24 mg/kg) did not significantly alter cocaine (0.75 mg/kg/infusion) self-administration reinforced under FR1 (one lever press for one cocaine infusion) conditions. However, acute administration of SB-277011A (24 mg/kg, i.p.) progressively attenuated cocaine self-administration when: (a) the unit dose of self-administered cocaine was lowered from 0.75 to 0.125–0.5 mg/kg, and (b) the work demand for cocaine reinforcement was increased from FR1 to FR10. Under PR (increasing number of lever presses for each successive cocaine infusion) cocaine reinforcement, acute administration of SB-277011A (6–24 mg/kg i.p.) lowered the PR break point for cocaine self-administration in a dose-dependent manner. The reduction in the cocaine (0.25–1.0 mg/kg) dose–response break-point curve produced by 24 mg/kg SB-277011A is consistent with a reduction in cocaine’s reinforcing efficacy. When substituted for cocaine, SB-277011A alone did not sustain self-administration behaviour. In contrast with the mixed DA D2/D3 receptor antagonist haloperidol (1 mg/kg), SB-277011A (3, 12 or 24 mg/kg) failed to impede locomotor activity, failed to impair rearing behaviour, failed to produce catalepsy and failed to impair rotarod performance. These results show that SB-277011A significantly inhibits acute cocaine-induced reinforcement except at high cocaine doses and low work requirement for cocaine. If these results extrapolate to humans, SB-277011A or similar selective DA D3 receptor antagonists may be

  7. Characteristics of Criteria for Selecting Investment Projects under Uncertainty

    Directory of Open Access Journals (Sweden)

    Adrian ENCIU

    2011-07-01

    Full Text Available Within financial theory and practice, there are used five main criteria for selecting investment projects: the net present value (NPV criterion, the internal rate of return (IRR criterion, the return term (RT criterion, the profitability ratio (PR criterion and the supplementary return (SR criterion. The assay will emphasize several new properties of said indexes for investment assessment, having as starting point the hypotheses of (approximately normal repartition of cash-flows generated by an investment project. The obtained results point to the fact that the NPV indexes (the analysis of this criterion was carried out in the article “The NPV Criterion for Valuing Investments under Uncertainty”, Daniel Armeanu, Leonard Lache, Economic Computation and Economic Cybernetics Studies and Research no. 4/2009, pp. 133-143, IRR, PR, RT and SR register normal repartitions, therefore simplifying the investment analysis under economic uncertainty, by the capacity of building confidence intervals and assessing probabilities for the inferior limits of said investment assessment indexes.

  8. Stability Criterion for a Finned Spinning Projectile

    OpenAIRE

    S. D. Naik

    2000-01-01

    The state-of-the-art in gun projectile technology has been used for the aerodynamic stabilisation.This approach is acceptable for guided and controlled rockets but the free-flight rockets suffer fromunacceptable dispersion. Sabot projectiles with both spin and fms developed during the last decadeneed careful analysis. In this study, the second method of Liapunov has been used to develop stability criterion for a projectile to be designed with small fins and is made to spin in the flight. This...

  9. Blind equalization with criterion with memory nonlinearity

    Science.gov (United States)

    Chen, Yuanjie; Nikias, Chrysostomos L.; Proakis, John G.

    1992-06-01

    Blind equalization methods usually combat the linear distortion caused by a nonideal channel via a transversal filter, without resorting to the a priori known training sequences. We introduce a new criterion with memory nonlinearity (CRIMNO) for the blind equalization problem. The basic idea of this criterion is to augment the Godard [or constant modulus algorithm (CMA)] cost function with additional terms that penalize the autocorrelations of the equalizer outputs. Several variations of the CRIMNO algorithms are derived, with the variations dependent on (1) whether the empirical averages or the single point estimates are used to approximate the expectations, (2) whether the recent or the delayed equalizer coefficients are used, and (3) whether the weights applied to the autocorrelation terms are fixed or are allowed to adapt. Simulation experiments show that the CRIMNO algorithm, and especially its adaptive weight version, exhibits faster convergence speed than the Godard (or CMA) algorithm. Extensions of the CRIMNO criterion to accommodate the case of correlated inputs to the channel are also presented.

  10. Selecting optimal feast-to-famine ratio for a new polyhydroxyalkanoate (PHA) production system fed by valerate-dominant sludge hydrolysate.

    Science.gov (United States)

    Hao, Jiuxiao; Wang, Hui; Wang, Xiujin

    2018-04-01

    The feast-to-famine ratio (F/F) represents the extent of selective pressure during polyhydroxyalkanoate (PHA) culture selection. This study evaluated the effects of F/F on a new PHA production system by an enriched culture with valerate-dominant sludge hydrolysate and selected the optimal F/F. After the original F/F 1/3 was modified to 1/1, 1/2, 1/4, and 1/5, F/F did not affect their lengths of feast phase, but affected their biomass growth behaviors during the famine phase and PHA-producing abilities. The optimal F/F was 1/2, and compared with 1/3, it increased the maximal PHA content and the fraction of 3-hydroxyvalerate (3HV) and 3-hydroxy-2-methylvalerate (3H2MV) monomers, with higher productivity and better polymer properties. Although F/F 1/2 impaired the advantage of the dominant genus Delftia, it improved the PHA production rate while decreased biomass growth rate, meanwhile enhancing the utilization and conversion of valerate. These findings indicate that in contrast to previous studies using acetate-dominant substrate for PHA production, the new system fed by valerate-dominant substrate can adopt a higher F/F.

  11. Shrinkage Porosity Criterion and Its Application to A 5.5 Ton Steel Ingot

    Directory of Open Access Journals (Sweden)

    Zhang C.

    2016-06-01

    Full Text Available In order to predict the distribution of shrinkage porosity in steel ingot efficiently and accurately, a criterion R√L and a method to obtain its threshold value were proposed. The criterion R√L was derived based on the solidification characteristics of steel ingot and pressure gradient in the mushy zone, in which the physical properties, the thermal parameters, the structure of the mushy zone and the secondary dendrite arm spacing were all taken into consideration. The threshold value of the criterion R√L was obtained with combination of numerical simulation of ingot solidification and total solidification shrinkage rate. Prediction of the shrinkage porosity in a 5.5 ton ingot of 2Cr13 steel with criterion R√L>0.21 m · °C1/2 · s−3/2 agreed well with the results of experimental sectioning. Based on this criterion, optimization of the ingot was carried out by decreasing the height-to-diameter ratio and increasing the taper, which successfully eliminated the centreline porosity and further proved the applicability of this criterion.

  12. The stressor criterion in DSM-IV posttraumatic stress disorder: an empirical investigation.

    Science.gov (United States)

    Breslau, N; Kessler, R C

    2001-11-01

    The DSM-IV two-part definition of posttraumatic stress disorder (PTSD) widened the variety of stressors (A1) and added a subjective component (A2). The effects of the revised stressor criterion on estimates of exposure and PTSD in a community sample are evaluated. A representative sample of 2181 persons in southeast Michigan were interviewed about lifetime history of traumatic events and PTSD. The evaluation of the revised two-part definition is based on a randomly selected sample of events that represents the total pool of traumatic events experienced in the community. The enlarged definition of stressors in A1 increased the total number of events that can be used to diagnose PTSD by 59%. The majority of A1 events (76.6%) involved the emotional response in A2. Females were more likely than males to endorse A2 (adjusted odds ratio = 2.66; 95% confidence interval 1.92, 3.71). Of all PTSD cases resulting from the representative sample of events, 38% were attributable to the expansion of qualifying events in A1. The identification of exposures that lead to PTSD were not improved materially by A2 however, events that did not involve A2 rarely resulted in PTSD. Compared to previous definitions, the wider variety of stressors in A1 markedly increased the number of events experienced in the community that can be used to diagnose PTSD. Furthermore, A2 might be useful as a separate criterion, an acute response necessary for the emergence of PTSD, and might serve as an early screen for identifying a subset of recently exposed persons at virtually no risk for PTSD. The utility of A2 as a screen must be tested prospectively.

  13. Novel global robust stability criterion for neural networks with delay

    International Nuclear Information System (INIS)

    Singh, Vimal

    2009-01-01

    A novel criterion for the global robust stability of Hopfield-type interval neural networks with delay is presented. An example illustrating the improvement of the present criterion over several recently reported criteria is given.

  14. Reactor instrumentation. Definition of the single failure criterion

    International Nuclear Information System (INIS)

    1980-12-01

    The standard defines the single failure criterion which is used in other IEC publications on reactor safety systems. The purpose of the single failure criterion is the assurance of minimum redundancy. (orig./HP) [de

  15. Two novel synchronization criterions for a unified chaotic system

    International Nuclear Information System (INIS)

    Tao Chaohai; Xiong Hongxia; Hu Feng

    2006-01-01

    Two novel synchronization criterions are proposed in this paper. It includes drive-response synchronization and adaptive synchronization schemes. Moreover, these synchronization criterions can be applied to a large class of chaotic systems and are very useful for secure communication

  16. Systems interaction and single failure criterion

    International Nuclear Information System (INIS)

    1981-01-01

    This report documents the results of a six-month study to evaluate the ongoing research programs of the U.S. Nuclear Regulatory Commission (NRC) and U.S. commercial nuclear station owners which address the safety significance of systems interaction and the regulatory adequacy of the single failure criterion. The evaluation of system interactions provided is the initial phase of a more detailed study leading to the development and application of methodology for quantifying the relative safety of operating nuclear plants. (Auth.)

  17. The Goiania accident: release from hospital criterion

    International Nuclear Information System (INIS)

    Falcao, R.C.; Hunt, J.

    1990-01-01

    On the thirteenth of September 1987, a 1357 Ci Cesium source was removed from the 'Instituto de Radiologia de Goiania' - probably two or three days later the source was opened, causing the internal and external contamination of 247 people, and part of the city of Goiania. This paper describes the release from hospital criterion of the contaminated patients, based on radiation protection principles which were developed for this case. The estimate of the biological half-life for cesium is also described. (author) [pt

  18. Early Stop Criterion from the Bootstrap Ensemble

    DEFF Research Database (Denmark)

    Hansen, Lars Kai; Larsen, Jan; Fog, Torben L.

    1997-01-01

    This paper addresses the problem of generalization error estimation in neural networks. A new early stop criterion based on a Bootstrap estimate of the generalization error is suggested. The estimate does not require the network to be trained to the minimum of the cost function, as required...... by other methods based on asymptotic theory. Moreover, in contrast to methods based on cross-validation which require data left out for testing, and thus biasing the estimate, the Bootstrap technique does not have this disadvantage. The potential of the suggested technique is demonstrated on various time...

  19. Impact of consanguineous marriages and degrees of inbreeding on fertility, child mortality, secondary sex ratio, selection intensity, and genetic load: a cross-sectional study from Northern India.

    Science.gov (United States)

    Fareed, Mohd; Kaisar Ahmad, Mir; Azeem Anwar, Malik; Afzal, Mohammad

    2017-01-01

    The aim of our study was to understand the relationship between consanguineous marriages and reproductive outcomes. A total of 999 families were recruited from five Muslim populations of Jammu region. Family pedigrees were drawn to access the family history and inbreeding status in terms of coefficient of inbreeding (F). Fertility, mortality, secondary sex ratio, selection intensity, and lethal equivalents were measured using standard methods. The significant differences for gross fertility was found to be higher among inbred groups as compared to the unrelated families (P consanguineous families of all populations in comparison with the non-consanguineous family groups. Moreover, the prenatal and postnatal child mortality rates (i.e., U5MR and U18MR) have presented a persuasive increase with an upsurge in the homozygosity level. The mortality rate was found to be maximum among families with the highest value of coefficient of inbreeding (F). The selection intensity (SI) also showed inflations among families with respect to their increasing inbreeding coefficients. The greater values of lethal equivalents per gamete (LEs/gamete) were observed for autosomal inheritance in comparison with sex-linked inheritance. Our conclusive assessment brings out the deleterious consequence of consanguineous marriages on reproductive outcomes.

  20. Covalent co-immobilization of heparin/laminin complex that with different concentration ratio on titanium surface for selectively direction of platelets and vascular cells behavior

    International Nuclear Information System (INIS)

    Wang, Jian; Chen, Yuan; Liu, Tao; Wang, Xue; Liu, Yang; Wang, Yuan; Chen, Junying; Huang, Nan

    2014-01-01

    Highlights: • Extracellular matrix inspired surface modification with fibronectin, heparin and VEGF to construct a favorable microenvironment for selectively anticoagulant and promote endothelialization. • Take the advantage of specific intermolecular interaction, the bioactivity of above biomolecules was more efficiently maintained in compared with the common used covalent immobilization method. • Poly-l-lysine was used as a novel interlayer for surface amination, and in comparison, PLL coating was more feasible and the degradation product had no harm to human body. - Abstract: Surface biofunctional modification of coronary artery stent to improve the hemocompatibility and selectively accelerate endothelium regeneration but prevent restenosis have been become a new hotspot. For this, a novel method was developed in this work by co-immobilization of Ln and heparin complex on poly-L-lysine modified Ti surface. Take the advantage of the specific interaction between Ln and heparin, Ln and heparin complexes with different concentration ratios were set up for creating different exposure density of these two types of biomolecules. According to biocompatibility evaluation results, the Hep/Ln complexes modified surface displayed less platelet adhesion and activation. Especially, on L(150)H and L(200)H surface, the AT III binding quantity, APTT value and anti-coagulation property of modified surface were significantly promoted. Furthermore, the adherent density and proliferation activity of ECs and EPCs were positively correlated with Ln concentration. Notably, the proliferation of both ECs and EPCs on L(100)H, L(150)H and L(200)H surface were greatly promoted. Another hand, the proliferation activity of SMCs was significantly inhibited on Hep/Ln modified surfaces, which was considered mainly due to the inhibitory effect of heparin to SMCs. According to the existing results, this study demonstrated that in a certain range of heparin and laminin concentration ratio

  1. A proposed risk acceptance criterion for nuclear fuel waste disposal

    International Nuclear Information System (INIS)

    Mehta, K.

    1985-06-01

    The need to establish a radiological protection criterion that applies specifically to disposal of high level nuclear fuel wastes arises from the difficulty of applying the present ICRP recommendations. These recommendations apply to situations in which radiological detriment can be actively controlled, while a permanent waste disposal facility is meant to operate without the need for corrective actions. Also, the risks associated with waste disposal depend on events and processes that have various probabilities of occurrence. In these circumstances, it is not suitable to apply standards that are based on a single dose limit as in the present ICRP recommendations, because it will generally be possible to envisage events, perhaps rare, that would lead to doses above any selected limit. To overcome these difficulties, it is proposed to base a criterion for acceptability on a set of dose values and corresponding limiting values of probabilities; this set of values constitutes a risk-limit line. A risk-limit line suitable for waste disposal is proposed that has characteristics consistent with the basic philosophy of the ICRP and UNSCEAR recommendations, and is based on levels on natural background radiation

  2. Extensions and applications of the Bohm criterion

    Science.gov (United States)

    Baalrud, Scott D.; Scheiner, Brett; Yee, Benjamin; Hopkins, Matthew; Barnat, Edward

    2015-04-01

    The generalized Bohm criterion is revisited in the context of incorporating kinetic effects of the electron and ion distribution functions into the theory. The underlying assumptions and results of two different approaches are compared: the conventional ‘kinetic Bohm criterion’ and a fluid-moment hierarchy approach. The former is based on the asymptotic limit of an infinitely thin sheath (λD/l = 0), whereas the latter is based on a perturbative expansion of a sheath that is thin compared to the plasma (λD/l ≪ 1). Here λD is the Debye length, which characterizes the sheath length scale, and l is a measure of the plasma or presheath length scale. The consequences of these assumptions are discussed in terms of how they restrict the class of distribution functions to which the resulting criteria can be applied. Two examples are considered to provide concrete comparisons between the two approaches. The first is a Tonks-Langmuir model including a warm ion source (Robertson 2009 Phys. Plasmas 16 103503). This highlights a substantial difference between the conventional kinetic theory, which predicts slow ions dominate at the sheath edge, and the fluid moment approach, which predicts slow ions have little influence. The second example considers planar electrostatic probes biased near the plasma potential using model equations and particle-in-cell simulations. This demonstrates a situation where electron kinetic effects alter the Bohm criterion, leading to a subsonic ion flow at the sheath edge.

  3. Specific strain work as a failure criterion in plane stress state

    International Nuclear Information System (INIS)

    Zuchowski, R.; Zietkowski, L.

    1985-01-01

    An experimental verification of failure criterion based on specific strain work was performed. Thin-walled cylindrical specimens were examined by loading with constant force and constant torque moment, assuming different values for particular tests, at the same time keeping stress intensity constant, and by subjecting to thermal cycling. It was found that the critical value of failure did not depend on axial-to-shearing stresses ratio, i.e., on the type of state of stress. Thereby, the validity of the analysed failure criterion in plane stress was confirmed. Besides, a simple description of damage development in plane stress was suggested. (orig./RF)

  4. Golden Ratio

    Indian Academy of Sciences (India)

    Our attraction to another body increases if the body is symmetricaland in proportion. If a face or a structure is in proportion,we are more likely to notice it and find it beautiful.The universal ratio of beauty is the 'Golden Ratio', found inmany structures. This ratio comes from Fibonacci numbers.In this article, we explore this ...

  5. Golden Ratio

    Indian Academy of Sciences (India)

    Keywords. Fibonacci numbers, golden ratio, Sanskrit prosody, solar panel. Abstract. Our attraction to another body increases if the body is symmetricaland in proportion. If a face or a structure is in proportion,we are more likely to notice it and find it beautiful.The universal ratio of beauty is the 'Golden Ratio', found inmany ...

  6. Golden Ratio

    Indian Academy of Sciences (India)

    Our attraction to another body increases if the body is sym- metrical and in proportion. If a face or a structure is in pro- portion, we are more likely to notice it and find it beautiful. The universal ratio of beauty is the 'Golden Ratio', found in many structures. This ratio comes from Fibonacci numbers. In this article, we explore this ...

  7. Fuel-pin cladding transient failure strain criterion

    International Nuclear Information System (INIS)

    Bard, F.E.; Duncan, D.R.; Hunter, C.W.

    1983-01-01

    A criterion for cladding failure based on accumulated strain was developed for mixed uranium-plutonium oxide fuel pins and used to interpret the calculated strain results from failed transient fuel pin experiments conducted in the Transient Reactor Test (TREAT) facility. The new STRAIN criterion replaced a stress-based criterion that depends on the DORN parameter and that incorrectly predicted fuel pin failure for transient tested fuel pins. This paper describes the STRAIN criterion and compares its prediction with those of the stress-based criterion

  8. Selection and reliability of financial ratios in an attempt to analyse financial statements. An empirical research of the listed companies at Greek stock exchange in Construction Sector. Dimitrios Tsiolis MA Finance

    OpenAIRE

    Tsiolis, Dimitrios

    2008-01-01

    Financial ratio analysis is a widely known financial statements analysis tool and is used to evaluate companies` financial position. Careful selection process in collaboration with other financial statement analysis techniques as well as taking into consideration the financial ratio analysis problems can lead the companies' analysts to a clear determination of their company's financial position.

  9. Extended equal areas criterion: foundations and applications

    Energy Technology Data Exchange (ETDEWEB)

    Yusheng, Xue [Nanjim Automation Research Institute, Nanjim (China)

    1994-12-31

    The extended equal area criterion (EEAC) provides analytical expressions for ultra fast transient stability assessment, flexible sensitivity analysis, and means to preventive and emergency controls. Its outstanding performances have been demonstrated by thousands upon thousands simulations on more than 50 real power systems and by on-line operation records in an EMS environment of Northeast China Power System since September 1992. However, the researchers have mainly based on heuristics and simulations. This paper lays a theoretical foundation of EEAC and brings to light the mechanism of transient stability. It proves true that the dynamic EEAC furnishes a necessary and sufficient condition for stability of multi machine systems with any detailed models, in the sense of the integration accuracy. This establishes a new platform for further advancing EEAC and better understanding of problems. An overview of EEAC applications in China is also given in this paper. (author) 30 refs.

  10. Application of the single failure criterion

    International Nuclear Information System (INIS)

    1990-01-01

    In order to present further details on the application and interpretation and on the limitations of individual concepts in the NUSS Codes and Safety Guides, a series of Safety Practice publications have been initiated. It is hoped that many Member States will be able to benefit from the experience presented in these books. The present publication will be useful not only to regulators but also to designers and could be particularly helpful in the interpretation of cases which fall on the borderline between the two areas. It should assist in clarifying, by way of examples, many of the concepts and implementation methods. It also describes some of the limitations involved. The book addresses a specialized topic and it is recommended that it be used together with the other books in the Safety Series. During the development of this publication the actual practices of all countries with major reactor programmes has been taken into account. An interpretation of the relevant text of the Design Code is given in the light of these national practices. The criterion is put into perspective with the general reliability requirements in which it is also embedded in the Design Code. Its relation to common cause and other multiple failure cases and also to the temporary disengagement of components in systems important to safety is clarified. Its use and its limitations are thus explained in the context of reliability targets for systems performance. The guidance provided applies to all reactor systems and would be applicable even to systems not in nuclear power plants. But since this publication was developed to give an interpretation of a specific requirement of the Design Code, the broader applicability is not explicitly claimed. The Design Code lists three cases for which compliance with the criterion may not be justified. The present publication assists in the more precise and practical identification of those cases. 9 figs, 1 tab

  11. Relationships between Classroom Schedule Types and Performance on the Algebra I Criterion-Referenced Test

    Science.gov (United States)

    Murray, Gregory V.; Moyer-Packenham, Patricia S.

    2014-01-01

    One option for length of individual mathematics class periods is the schedule type selected for Algebra I classes. This study examined the relationship between student achievement, as indicated by Algebra I Criterion-Referenced Test scores, and the schedule type for Algebra I classes. Data obtained from the Utah State Office of Education included…

  12. Hesperetin-7,3'-O-dimethylether selectively inhibits phosphodiesterase 4 and effectively suppresses ovalbumin-induced airway hyperresponsiveness with a high therapeutic ratio

    Directory of Open Access Journals (Sweden)

    Yang You-Lan

    2011-11-01

    Full Text Available Abstract Background Hesperetin was reported to selectively inhibit phosphodiesterase 4 (PDE4. While hesperetin-7,3'-O-dimethylether (HDME is a synthetic liposoluble hesperetin. Therefore, we were interested in investigating its selectivity on PDE4 and binding ability on high-affinity rolipram-binding sites (HARBs in vitro, and its effects on ovalbumin-induced airway hyperresponsiveness in vivo, and clarifying its potential for treating asthma and chronic obstructive pulmonary disease (COPD. Methods PDE1~5 activities were measured using a two-step procedure. The binding of HDME on high-affinity rolipram-binding sites was determined by replacing 2 nM [3H]-rolipram. AHR was assessed using the FlexiVent system and barometric plethysmography. Inflammatory cells were counted using a hemocytometer. Cytokines were determined using mouse T helper (Th1/Th2 cytokine CBA kits, and total immunoglobulin (IgE or IgG2a levels were done using ELISA method. Xylazine (10 mg/kg/ketamine (70 mg/kg-induced anesthesia was performed. Results HDME revealed selective phosphodiesterase 4 (PDE4 inhibition with a therapeutic (PDE4H/PDE4L ratio of 35.5 in vitro. In vivo, HDME (3~30 μmol/kg, orally (p.o. dose-dependently and significantly attenuated the airway resistance (RL and increased lung dynamic compliance (Cdyn, and decreased enhanced pause (Penh values induced by methacholine in sensitized and challenged mice. It also significantly suppressed the increases in the numbers of total inflammatory cells, macrophages, lymphocytes, neutrophils, and eosinophils, and levels of cytokines, including interleukin (IL-2, IL-4, IL-5, interferon-γ, and tumor necrosis factor-α in bronchoalveolar lavage fluid (BALF of these mice. In addition, HDME (3~30 μmol/kg, p.o. dose-dependently and significantly suppressed total and ovalbumin-specific immunoglobulin (IgE levels in the BALF and serum, and enhanced IgG2a level in the serum of these mice. Conclusions HDME exerted anti

  13. Optimal Conformal Polynomial Projections for Croatia According to the Airy/Jordan Criterion

    Directory of Open Access Journals (Sweden)

    Dražen Tutić

    2009-05-01

    Full Text Available The paper describes optimal conformal polynomial projections for Croatia according to the Airy/Jordan criterion. A brief introduction of history and theory of conformal mapping is followed by descriptions of conformal polynomial projections and their current application. The paper considers polynomials of degrees 1 to 10. Since there are conditions in which the 1st degree polynomial becomes the famous Mercator projection, it was not considered specifically for Croatian territory. The area of Croatia was defined as a union of national territory and the continental shelf. Area definition data were taken from the Euro Global Map 1:1 000 000 for Croatia, as well as from two maritime delimitation treaties. Such an irregular area was approximated with a regular grid consisting of 11 934 ellipsoidal trapezoids 2' large. The Airy/Jordan criterion for the optimal projection is defined as minimum of weighted mean of Airy/Jordan measure of distortion in points. The value of the Airy/Jordan criterion is calculated from all 11 934 centres of ellipsoidal trapezoids, while the weights are equal to areas of corresponding ellipsoidal trapezoids. The minimum is obtained by Nelder and Mead’s method, as implemented in the fminsearch function of the MATLAB package. Maps of Croatia representing the distribution of distortions are given for polynomial degrees 2 to 6 and 10. Increasing the polynomial degree results in better projections considering the criterion, and the 6th degree polynomial provides a good ratio of formula complexity and criterion value.

  14. Sex ratios

    OpenAIRE

    West, Stuart A; Reece, S E; Sheldon, Ben C

    2002-01-01

    Sex ratio theory attempts to explain variation at all levels (species, population, individual, brood) in the proportion of offspring that are male (the sex ratio). In many cases this work has been extremely successful, providing qualitative and even quantitative explanations of sex ratio variation. However, this is not always the situation, and one of the greatest remaining problems is explaining broad taxonomic patterns. Specifically, why do different organisms show so ...

  15. An Empirical Model Building Criterion Based on Prediction with Applications in Parametric Cost Estimation.

    Science.gov (United States)

    1980-08-01

    varia- ble is denoted by 7, the total sum of squares of deviations from that mean is defined by n - SSTO - (-Y) (2.6) iul and the regression sum of...squares by SSR - SSTO - SSE (2.7) II 14 A selection criterion is a rule according to which a certain model out of the 2p possible models is labeled "best...dis- cussed next. 1. The R2 Criterion The coefficient of determination is defined by R2 . 1 - SSE/ SSTO . (2.8) It is clear that R is the proportion of

  16. Discussion on verification criterion and method of human factors engineering for nuclear power plant controller

    International Nuclear Information System (INIS)

    Yang Hualong; Liu Yanzi; Jia Ming; Huang Weijun

    2014-01-01

    In order to prevent or reduce human error and ensure the safe operation of nuclear power plants, control device should be verified from the perspective of human factors engineering (HFE). The domestic and international human factors engineering guidelines about nuclear power plant controller were considered, the verification criterion and method of human factors engineering for nuclear power plant controller were discussed and the application examples were provided for reference in this paper. The results show that the appropriate verification criterion and method should be selected to ensure the objectivity and accuracy of the conclusion. (authors)

  17. ADDED VALUE AS EFFICIENCY CRITERION FOR INDUSTRIAL PRODUCTION PROCESS

    Directory of Open Access Journals (Sweden)

    L. M. Korotkevich

    2016-01-01

    Full Text Available Literary analysis has shown that the majority of researchers are using classical efficiency criteria for construction of an optimization model for production process: profit maximization; cost minimization; maximization of commercial product output; minimization of back-log for product demand; minimization of total time consumption due to production change. The paper proposes to use an index of added value as an efficiency criterion because it combines economic and social interests of all main interested subjects of the business activity: national government, property owners, employees, investors. The following types of added value have been considered in the paper: joint-stock, market, monetary, economic, notional (gross, net, real. The paper makes suggestion to use an index of real value added as an efficiency criterion. Such approach permits to bring notional added value in comparable variant because added value can be increased not only due to efficiency improvement of enterprise activity but also due to environmental factors – excess in rate of export price increases over rate of import growth. An analysis of methods for calculation of real value added has been made on a country-by-country basis (extrapolation, simple and double deflation. A method of double deflation has been selected on the basis of the executed analysis and it is counted according to the Laspeyires, Paasche, Fischer indices. A conclusion has been made that the used expressions do not take into account fully economic peculiarities of the Republic of Belarus: they are considered as inappropriate in the case when product cost is differentiated according to marketing outlets; they do not take account of difference in rate of several currencies and such approach is reflected in export price of a released product and import price for raw material, supplies and component parts. Taking this into consideration expressions for calculation of real value added have been specified

  18. A criterion for heated pipe design by linear electric resistances

    International Nuclear Information System (INIS)

    Bloch, M.; Cruz, J.R.B.

    1984-01-01

    A criterion for linear eletrical elements instalation on horizontal tubes is obtainned in this work. This criterion is based upon the calculation of the thermal stresses caused by the non uniform temperature distribution in the tube cross section. The finite difference method and the SAP IV computer code are both used in the calculations. The criterion is applied to the thermal circuits of the IEN which has tube diameter varying from φ 1/2 in till φ 8 in. (author) [pt

  19. Suboptimal Criterion Learning in Static and Dynamic Environments.

    Directory of Open Access Journals (Sweden)

    Elyse H Norton

    2017-01-01

    Full Text Available Humans often make decisions based on uncertain sensory information. Signal detection theory (SDT describes detection and discrimination decisions as a comparison of stimulus "strength" to a fixed decision criterion. However, recent research suggests that current responses depend on the recent history of stimuli and previous responses, suggesting that the decision criterion is updated trial-by-trial. The mechanisms underpinning criterion setting remain unknown. Here, we examine how observers learn to set a decision criterion in an orientation-discrimination task under both static and dynamic conditions. To investigate mechanisms underlying trial-by-trial criterion placement, we introduce a novel task in which participants explicitly set the criterion, and compare it to a more traditional discrimination task, allowing us to model this explicit indication of criterion dynamics. In each task, stimuli were ellipses with principal orientations drawn from two categories: Gaussian distributions with different means and equal variance. In the covert-criterion task, observers categorized a displayed ellipse. In the overt-criterion task, observers adjusted the orientation of a line that served as the discrimination criterion for a subsequently presented ellipse. We compared performance to the ideal Bayesian learner and several suboptimal models that varied in both computational and memory demands. Under static and dynamic conditions, we found that, in both tasks, observers used suboptimal learning rules. In most conditions, a model in which the recent history of past samples determines a belief about category means fit the data best for most observers and on average. Our results reveal dynamic adjustment of discrimination criterion, even after prolonged training, and indicate how decision criteria are updated over time.

  20. The Concept of Performance Levels in Criterion-Referenced Assessment.

    Science.gov (United States)

    Hewitson, Mal

    The concept of performance levels in criterion-referenced assessment is explored by applying the idea to different types of tests commonly used in schools, mastery tests (including diagnostic tests) and achievement tests. In mastery tests, a threshold performance standard must be established for each criterion. Attainment of this threshold…

  1. Modified Schur-Cohn Criterion for Stability of Delayed Systems

    Directory of Open Access Journals (Sweden)

    Juan Ignacio Mulero-Martínez

    2015-01-01

    Full Text Available A modified Schur-Cohn criterion for time-delay linear time-invariant systems is derived. The classical Schur-Cohn criterion has two main drawbacks; namely, (i the dimension of the Schur-Cohn matrix generates some round-off errors eventually resulting in a polynomial of s with erroneous coefficients and (ii imaginary roots are very hard to detect when numerical errors creep in. In contrast to the classical Schur-Cohn criterion an alternative approach is proposed in this paper which is based on the application of triangular matrices over a polynomial ring in a similar way as in the Jury test of stability for discrete systems. The advantages of the proposed approach are that it halves the dimension of the polynomial and it only requires seeking real roots, making this modified criterion comparable to the Rekasius substitution criterion.

  2. Asymptotics for ratios with applications to reinsurance

    NARCIS (Netherlands)

    Ladoucette, S.A.; Teugels, J.L.

    2007-01-01

    This paper provides an overview of results pertaining to moment convergence for certain ratios of random variables involving sums, order statistics and extreme terms in the sense of modulus. Most of the literature on this matter originates from Darling (1952) who gave a criterion for the convergence

  3. Optimal selection of annulus radius ratio to enhance heat transfer with minimum entropy generation in developing laminar forced convection of water-Al2O3 nanofluid flow

    Institute of Scientific and Technical Information of China (English)

    Siavashi Majid; Jamali Mohammad

    2017-01-01

    Heat transfer and entropy generation of developing laminar forced convection flow of water-Al2O3 nanofluid in a concentric annulus with constant heat flux on the walls is investigated numerically. In order to determine entropy generation of fully developed flow, two approaches are employed and it is shown that only one of these methods can provide appropriate results for flow inside annuli. The effects of concentration of nanoparticles, Reynolds number and thermal boundaries on heat transfer enhancement and entropy generation of developing laminar flow inside annuli with different radius ratios and same cross sectional areas are studied. The results show that radius ratio is a very important decision parameter of an annular heat exchanger such that in each Re, there is an optimum radius ratio to maximize Nu and minimize entropy generation. Moreover, the effect of nanoparticles concentration on heat transfer enhancement and minimizing entropy generation is stronger at higher Reynolds.

  4. Failure Criterion for Brick Masonry: A Micro-Mechanics Approach

    Directory of Open Access Journals (Sweden)

    Kawa Marek

    2015-02-01

    Full Text Available The paper deals with the formulation of failure criterion for an in-plane loaded masonry. Using micro-mechanics approach the strength estimation for masonry microstructure with constituents obeying the Drucker-Prager criterion is determined numerically. The procedure invokes lower bound analysis: for assumed stress fields constructed within masonry periodic cell critical load is obtained as a solution of constrained optimization problem. The analysis is carried out for many different loading conditions at different orientations of bed joints. The performance of the approach is verified against solutions obtained for corresponding layered and block microstructures, which provides the upper and lower strength bounds for masonry microstructure, respectively. Subsequently, a phenomenological anisotropic strength criterion for masonry microstructure is proposed. The criterion has a form of conjunction of Jaeger critical plane condition and Tsai-Wu criterion. The model proposed is identified based on the fitting of numerical results obtained from the microstructural analysis. Identified criterion is then verified against results obtained for different loading orientations. It appears that strength of masonry microstructure can be satisfactorily described by the criterion proposed.

  5. Nonparametric adaptive age replacement with a one-cycle criterion

    International Nuclear Information System (INIS)

    Coolen-Schrijner, P.; Coolen, F.P.A.

    2007-01-01

    Age replacement of technical units has received much attention in the reliability literature over the last four decades. Mostly, the failure time distribution for the units is assumed to be known, and minimal costs per unit of time is used as optimality criterion, where renewal reward theory simplifies the mathematics involved but requires the assumption that the same process and replacement strategy continues over a very large ('infinite') period of time. Recently, there has been increasing attention to adaptive strategies for age replacement, taking into account the information from the process. Although renewal reward theory can still be used to provide an intuitively and mathematically attractive optimality criterion, it is more logical to use minimal costs per unit of time over a single cycle as optimality criterion for adaptive age replacement. In this paper, we first show that in the classical age replacement setting, with known failure time distribution with increasing hazard rate, the one-cycle criterion leads to earlier replacement than the renewal reward criterion. Thereafter, we present adaptive age replacement with a one-cycle criterion within the nonparametric predictive inferential framework. We study the performance of this approach via simulations, which are also used for comparisons with the use of the renewal reward criterion within the same statistical framework

  6. Criterion for burn-up conditions in gas-cooled cryogenic current leads

    International Nuclear Information System (INIS)

    Bejan, A.; Cluss, E.M. Jr.

    1976-01-01

    Superconducting magnets are energized through helium vapour-cooled cryogenic current leads operating at high ratios of current to mass flow. The high current operation where lead temperature, runaway, and eventual burn-up are likely to occur is investigated. A simple criterion for estimating the burn-up operation conditions (current, mass flow) for a given lead geometry (cross-sectional area, length, heat exchanger area) is presented. This article stresses the role played by the available heat exchanger area in avoiding burn-up at high ratios of current to mass flow. (author)

  7. Generalized Empirical Likelihood-Based Focused Information Criterion and Model Averaging

    Directory of Open Access Journals (Sweden)

    Naoya Sueishi

    2013-07-01

    Full Text Available This paper develops model selection and averaging methods for moment restriction models. We first propose a focused information criterion based on the generalized empirical likelihood estimator. We address the issue of selecting an optimal model, rather than a correct model, for estimating a specific parameter of interest. Then, this study investigates a generalized empirical likelihood-based model averaging estimator that minimizes the asymptotic mean squared error. A simulation study suggests that our averaging estimator can be a useful alternative to existing post-selection estimators.

  8. Statistical surrogate model based sampling criterion for stochastic global optimization of problems with constraints

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Su Gil; Jang, Jun Yong; Kim, Ji Hoon; Lee, Tae Hee [Hanyang University, Seoul (Korea, Republic of); Lee, Min Uk [Romax Technology Ltd., Seoul (Korea, Republic of); Choi, Jong Su; Hong, Sup [Korea Research Institute of Ships and Ocean Engineering, Daejeon (Korea, Republic of)

    2015-04-15

    Sequential surrogate model-based global optimization algorithms, such as super-EGO, have been developed to increase the efficiency of commonly used global optimization technique as well as to ensure the accuracy of optimization. However, earlier studies have drawbacks because there are three phases in the optimization loop and empirical parameters. We propose a united sampling criterion to simplify the algorithm and to achieve the global optimum of problems with constraints without any empirical parameters. It is able to select the points located in a feasible region with high model uncertainty as well as the points along the boundary of constraint at the lowest objective value. The mean squared error determines which criterion is more dominant among the infill sampling criterion and boundary sampling criterion. Also, the method guarantees the accuracy of the surrogate model because the sample points are not located within extremely small regions like super-EGO. The performance of the proposed method, such as the solvability of a problem, convergence properties, and efficiency, are validated through nonlinear numerical examples with disconnected feasible regions.

  9. Positive Selection of Deleterious Alleles through Interaction with a Sex-Ratio Suppressor Gene in African Buffalo: A Plausible New Mechanism for a High Frequency Anomaly

    NARCIS (Netherlands)

    Hooft, van W.F.; Greyling, B.J.; Getz, W.M.; Helden, P.D.; Zwaan, B.J.; Bastos, A.D.S.

    2015-01-01

    Although generally rare, deleterious alleles can become common through genetic drift, hitchhiking or reductions in selective constraints. Here we present a possible new mechanism that explains the attainment of high frequencies of deleterious alleles in the African buffalo (Syncerus caffer)

  10. Positive Selection of Deleterious Alleles through Interaction with a Sex-Ratio Suppressor Gene in African Buffalo: A Plausible New Mechanism for a High Frequency Anomaly

    NARCIS (Netherlands)

    Hooft, van W.F.; Greyling, B.J.; Getz, W.M.; Helden, van P.D.; Zwaan, B.J.; Bastos, A.D.S.

    2014-01-01

    Although generally rare, deleterious alleles can become common through genetic drift, hitchhiking or reductions in selective constraints. Here we present a possible new mechanism that explains the attainment of high frequencies of deleterious alleles in the African buffalo (Syncerus caffer)

  11. Criterion for testing multiparticle negative-partial-transpose entanglement

    International Nuclear Information System (INIS)

    Zeng, B.; Zhou, D.L.; Zhang, P.; Xu, Z.; You, L.

    2003-01-01

    We revisit the criterion of multiparticle entanglement based on the overlaps of a given quantum state ρ with maximally entangled states. For a system of m particles, each with N distinct states, we prove that ρ is m-particle negative partial transpose entangled, if there exists a maximally entangled state vertical bar MES>, such that >1/N. While this sufficiency condition is weaker than the Peres-Horodecki criterion in all cases, it applies to multi-particle systems, and becomes especially useful when the number of particles (m) is large. We also consider the converse of this criterion and illustrate its invalidity with counter examples

  12. Industry Software Trustworthiness Criterion Research Based on Business Trustworthiness

    Science.gov (United States)

    Zhang, Jin; Liu, Jun-fei; Jiao, Hai-xing; Shen, Yi; Liu, Shu-yuan

    To industry software Trustworthiness problem, an idea aiming to business to construct industry software trustworthiness criterion is proposed. Based on the triangle model of "trustworthy grade definition-trustworthy evidence model-trustworthy evaluating", the idea of business trustworthiness is incarnated from different aspects of trustworthy triangle model for special industry software, power producing management system (PPMS). Business trustworthiness is the center in the constructed industry trustworthy software criterion. Fusing the international standard and industry rules, the constructed trustworthy criterion strengthens the maneuverability and reliability. Quantitive evaluating method makes the evaluating results be intuitionistic and comparable.

  13. Criterion of damage beginning: experimental identification for laminate composite

    International Nuclear Information System (INIS)

    Thiebaud, F.; Perreux, D.; Varchon, D.; Lebras, J.

    1996-01-01

    The aim of this study is to propose a criterion of damage beginning for laminate composite. The materials is a glass-epoxy laminate [+55 deg.,-55 deg.[ n performed by winding filament process. First of all a description of the damage is performed and allows to define a damage variable. Thanks to the potential of free energy, an associated variable is defined. The damage criterion is written by using this last one. The parameter of the criterion is identified using mechanical and acoustical methods. The result is compared and exhibit a good agreement. (authors). 13 refs., 5 figs

  14. Improvement of the butanol production selectivity and butanol to acetone ratio (B:A) by addition of electron carriers in the batch culture of a new local isolate of Clostridium acetobutylicum YM1.

    Science.gov (United States)

    Nasser Al-Shorgani, Najeeb Kaid; Kalil, Mohd Sahaid; Wan Yusoff, Wan Mohtar; Shukor, Hafiza; Hamid, Aidil Abdul

    2015-12-01

    Improvement in the butanol production selectivity or enhanced butanol:acetone ratio (B:A) is desirable in acetone-butanol-ethanol (ABE) fermentation by Clostridium strains. In this study, artificial electron carriers were added to the fermentation medium of a new isolate of Clostridium acetobutylicum YM1 in order to improve the butanol yield and B:A ratio. The results revealed that medium supplementation with electron carriers changed the metabolism flux of electron and carbon in ABE fermentation by YM1. A decrease in acetone production, which subsequently improved the B:A ratio, was observed. Further improvement in the butanol production and B:A ratios were obtained when the fermentation medium was supplemented with butyric acid. The maximum butanol production (18.20 ± 1.38 g/L) was gained when a combination of methyl red and butyric acid was added. Although the addition of benzyl viologen (0.1 mM) and butyric acid resulted in high a B:A ratio of 16:1 (800% increment compared with the conventional 2:1 ratio), the addition of benzyl viologen to the culture after 4 h resulted in the production of 18.05 g/L butanol. Manipulating the metabolic flux to butanol through the addition of electron carriers could become an alternative strategy to achieve higher butanol productivity and improve the B:A ratio. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Numerical and Experimental Validation of a New Damage Initiation Criterion

    Science.gov (United States)

    Sadhinoch, M.; Atzema, E. H.; Perdahcioglu, E. S.; van den Boogaard, A. H.

    2017-09-01

    Most commercial finite element software packages, like Abaqus, have a built-in coupled damage model where a damage evolution needs to be defined in terms of a single fracture energy value for all stress states. The Johnson-Cook criterion has been modified to be Lode parameter dependent and this Modified Johnson-Cook (MJC) criterion is used as a Damage Initiation Surface (DIS) in combination with the built-in Abaqus ductile damage model. An exponential damage evolution law has been used with a single fracture energy value. Ultimately, the simulated force-displacement curves are compared with experiments to validate the MJC criterion. 7 out of 9 fracture experiments were predicted accurately. The limitations and accuracy of the failure predictions of the newly developed damage initiation criterion will be discussed shortly.

  16. Importance biasing quality criterion based on contribution response theory

    International Nuclear Information System (INIS)

    Borisov, N.M.; Panin, M.P.

    2001-01-01

    The report proposes a visual criterion of importance biasing both of forward and adjoint simulation. The similarity of contribution Monte Carlo and importance biasing random collision event distribution is proved. The conservation of total number of random trajectory crossings of surfaces, which separate the source and the detector is proposed as importance biasing quality criterion. The use of this criterion is demonstrated on the example of forward vs. adjoint importance biasing in gamma ray deep penetration problem. The larger amount of published data on forward field characteristics than on adjoint leads to the more accurate approximation of adjoint importance function in comparison to forward, for it adjoint importance simulation is more effective than forward. The proposed criterion indicates it visually, showing the most uniform distribution of random trajectory crossing events for the most effective importance biasing parameters and pointing to the direction of tuning importance biasing parameters. (orig.)

  17. A multipole acceptability criterion for electronic structure theory

    International Nuclear Information System (INIS)

    Schwegler, E.; Challacombe, M.; Head-Gordon, M.

    1998-01-01

    Accurate and computationally inexpensive estimates of multipole expansion errors are crucial to the success of several fast electronic structure methods. In this paper, a new nonempirical multipole acceptability criterion is described that is directly applicable to expansions of high order moments. Several model calculations typical of electronic structure theory are presented to demonstrate its performance. For cases involving small translation distances, accuracies are increased by up to five orders of magnitude over an empirical criterion. The new multipole acceptance criterion is on average within an order of magnitude of the exact expansion error. Use of the multipole acceptance criterion in hierarchical multipole based methods as well as in traditional electronic structure methods is discussed. copyright 1998 American Institute of Physics

  18. Bayesian Information Criterion as an Alternative way of Statistical Inference

    Directory of Open Access Journals (Sweden)

    Nadejda Yu. Gubanova

    2012-05-01

    Full Text Available The article treats Bayesian information criterion as an alternative to traditional methods of statistical inference, based on NHST. The comparison of ANOVA and BIC results for psychological experiment is discussed.

  19. Angular criterion for distinguishing between Fraunhofer and Fresnel diffraction

    International Nuclear Information System (INIS)

    Medina, Francisco F.; Garcia-Sucerquia, Jorge; Castaneda, Roman; Matteucci, Giorgio

    2003-03-01

    The distinction between Fresnel and Fraunhofer diffraction is a crucial condition for the accurate analysis of diffracting structures. In this paper we propose a criterion based on the angle subtended by the first zero of the diffraction pattern from the center of the diffracting aperture. The determination of the zero of the diffraction pattern is the crucial point for assuring the precision of the criterion. It mainly depends on the dynamical range of the detector. Therefore, the applicability of adequate thresholds for different detector types is discussed. The criterion is also generalized by expressing it in terms of the number of Fresnel zones delimited by the aperture. Simulations are reported for illustrating the feasibility of the criterion. (author)

  20. Systematic variations of 87Sr/56Sr ratios, Sr compositions, selected major-oxide concentrations, and mineral abundances in piston cores from the Red Sea

    International Nuclear Information System (INIS)

    Boger, P.D.; Boger, J.L.; Faure, G.

    1980-01-01

    A mixing model is presented which relates the concentrations of Sr to the 87 Sr/ 86 Sr ratios and concentrations of other elements contained in a mixture of two components. The model is applied to the measured 87 Sr/ 86 Sr ratios, Sr, CaO, Fe 2 O 3 and SiO 2 concentrations of the detrital fractions of sediment from three piston cores representing different depositional environments in the Red Sea. The sediment is shown to be a mixture of two components derived from old sialic rocks and young volcanic rocks of the surrounding land masses. One of the cores contained a third component which is identified as authigenic Fe 2 O 3 . Removal of this contaminant is shown to return the system to its original detrital constituents. (Auth.)

  1. Unit rupture work as a criterion for quantitative estimation of hardenability in steel

    International Nuclear Information System (INIS)

    Kramarov, M.A.; Orlov, E.D.; Rybakov, A.B.

    1980-01-01

    Shown is possible utilization of high sensitivity of resistance to fracture of structural steel to the hardenability degree in the course of hardening to find the quantitative estimation of the latter one. Proposed is a criterion kappa, the ratio of the unit rupture work in the case of incomplete hardenability (asub(Tsub(ih))) under investigation, and the analoguc value obtained in the case of complete hardenability Asub(Tsub(Ch)) at the testing temperature corresponding to the critical temperature Tsub(100(M). Confirmed is high criterion sensitivity of the hardened steel structure on the basis of experimental investigation of the 40Kh, 38KhNM and 38KhNMFA steels after isothermal hold-up at different temperatures, corresponding to production of various products of austenite decomposition

  2. A Criterion to Identify Maximally Entangled Four-Qubit State

    International Nuclear Information System (INIS)

    Zha Xinwei; Song Haiyang; Feng Feng

    2011-01-01

    Paolo Facchi, et al. [Phys. Rev. A 77 (2008) 060304(R)] presented a maximally multipartite entangled state (MMES). Here, we give a criterion for the identification of maximally entangled four-qubit states. Using this criterion, we not only identify some existing maximally entangled four-qubit states in the literature, but also find several new maximally entangled four-qubit states as well. (general)

  3. Self-Adjointness Criterion for Operators in Fock Spaces

    International Nuclear Information System (INIS)

    Falconi, Marco

    2015-01-01

    In this paper we provide a criterion of essential self-adjointness for operators in the tensor product of a separable Hilbert space and a Fock space. The class of operators we consider may contain a self-adjoint part, a part that preserves the number of Fock space particles and a non-diagonal part that is at most quadratic with respect to the creation and annihilation operators. The hypotheses of the criterion are satisfied in several interesting applications

  4. Decision criterion dynamics in animals performing an auditory detection task.

    Directory of Open Access Journals (Sweden)

    Robert W Mill

    Full Text Available Classical signal detection theory attributes bias in perceptual decisions to a threshold criterion, against which sensory excitation is compared. The optimal criterion setting depends on the signal level, which may vary over time, and about which the subject is naïve. Consequently, the subject must optimise its threshold by responding appropriately to feedback. Here a series of experiments was conducted, and a computational model applied, to determine how the decision bias of the ferret in an auditory signal detection task tracks changes in the stimulus level. The time scales of criterion dynamics were investigated by means of a yes-no signal-in-noise detection task, in which trials were grouped into blocks that alternately contained easy- and hard-to-detect signals. The responses of the ferrets implied both long- and short-term criterion dynamics. The animals exhibited a bias in favour of responding "yes" during blocks of harder trials, and vice versa. Moreover, the outcome of each single trial had a strong influence on the decision at the next trial. We demonstrate that the single-trial and block-level changes in bias are a manifestation of the same criterion update policy by fitting a model, in which the criterion is shifted by fixed amounts according to the outcome of the previous trial and decays strongly towards a resting value. The apparent block-level stabilisation of bias arises as the probabilities of outcomes and shifts on single trials mutually interact to establish equilibrium. To gain an intuition into how stable criterion distributions arise from specific parameter sets we develop a Markov model which accounts for the dynamic effects of criterion shifts. Our approach provides a framework for investigating the dynamics of decisions at different timescales in other species (e.g., humans and in other psychological domains (e.g., vision, memory.

  5. New decision criteria for selecting delta check methods based on the ratio of the delta difference to the width of the reference range can be generally applicable for each clinical chemistry test item.

    Science.gov (United States)

    Park, Sang Hyuk; Kim, So-Young; Lee, Woochang; Chun, Sail; Min, Won-Ki

    2012-09-01

    Many laboratories use 4 delta check methods: delta difference, delta percent change, rate difference, and rate percent change. However, guidelines regarding decision criteria for selecting delta check methods have not yet been provided. We present new decision criteria for selecting delta check methods for each clinical chemistry test item. We collected 811,920 and 669,750 paired (present and previous) test results for 27 clinical chemistry test items from inpatients and outpatients, respectively. We devised new decision criteria for the selection of delta check methods based on the ratio of the delta difference to the width of the reference range (DD/RR). Delta check methods based on these criteria were compared with those based on the CV% of the absolute delta difference (ADD) as well as those reported in 2 previous studies. The delta check methods suggested by new decision criteria based on the DD/RR ratio corresponded well with those based on the CV% of the ADD except for only 2 items each in inpatients and outpatients. Delta check methods based on the DD/RR ratio also corresponded with those suggested in the 2 previous studies, except for 1 and 7 items in inpatients and outpatients, respectively. The DD/RR method appears to yield more feasible and intuitive selection criteria and can easily explain changes in the results by reflecting both the biological variation of the test item and the clinical characteristics of patients in each laboratory. We suggest this as a measure to determine delta check methods.

  6. Determination of selected endogenous anabolic androgenic steroids and ratios in urine by ultra high performance liquid chromatography tandem mass spectrometry and isotope pattern deconvolution.

    Science.gov (United States)

    Pitarch-Motellón, J; Sancho, J V; Ibáñez, M; Pozo, O; Roig-Navarro, A F

    2017-09-15

    An isotope dilution mass spectrometry (IDMS) method for the determination of selected endogenous anabolic androgenic steroids (EAAS) in urine by UHPLC-MS/MS has been developed using the isotope pattern deconvolution (IPD) mathematical tool. The method has been successfully validated for testosterone, epitestosterone, androsterone and etiocholanolone, employing their respective deuterated analogs using two certified reference materials (CRM). Accuracy was evaluated as recovery of the certified values and ranged from 75% to 108%. Precision was assessed in intraday (n=5) and interday (n=4) experiments, with RSDs below 5% and 10% respectively. The method was also found suitable for real urine samples, with limits of detection (LOD) and quantification (LOQ) below the normal urinary levels. The developed method meets the requirements established by the World Anti-Doping Agency for the selected steroids for Athlete Biological Passport (ABP) measurements, except in the case of androsterone, which is currently under study. Copyright © 2017. Published by Elsevier B.V.

  7. Thermodynamic criterions for heat exchanger networks design

    Energy Technology Data Exchange (ETDEWEB)

    Guiglion, C.; Farhat, S.; Pibouleau, L.; Domenech, S. (Ecole Nationale Superieure d' Ingenieurs de Genie Chimique, 31 - Toulouse (France))

    1994-03-01

    This problem under consideration consists in selecting a heat exchanger network able to carry out a given request in heatings and coolings, in steady-state behaviour with constant pressure, by using if necessary cold and hot utilities, and under the constraint [Delta] T [>=] e in order to restrict investment costs. The exchanged energy and the produced entropy are compared in terms of operating costs. According to the request to be satisfied and the constraints of utility consumption, it is shown that the goal to minimize the produced entropy more or less agrees with the goal to minimize the exchanged energy. In the last part, the case where the cost of utility use is assumed to be proportional to the flow rate, with a proportionality constant only depending on the input thermodynamic state, is studied thoroughly. Under this assumption, the minimization of operating costs is compatible with the minimization of exchanged energy, and can be obtained via the maximization of the difficulty of the request part, made without using utilities. This point is based on the notion of a request easier than another, which explicits the quite vague idea that a request is all the more easier because it involves less heatings at high temperatures and less coolings at low temperatures. (author). 5 refs., 1 fig.

  8. The AP diameter of the pelvis: a new criterion for continence in the exstrophy complex?

    International Nuclear Information System (INIS)

    Ait-Ameur, A.; Kalifa, G.; Adamsbaum, C.; Wakim, A.; Dubousset, J.

    2001-01-01

    Reconstructive surgery of bladder exstrophy remains a challenge. By using CT of the pelvis, we suggest a new pre- and post-operative investigative procedure to define the AP diameter (APD) as a predictive criterion for continence in this anomaly. Patients and methods: Three axial CT slices were selected in nine children with exstrophy who had undergone neonatal reconstructive surgery. The three levels selected were the first sacral plate, the mid acetabular plane and the superior pubic spine. We used combined slices to measure: circle APD = distance between the first sacral vertebra and the pubic symphysis. circle Pubic diastasis (PD) circle Three angles defined on the transverse plane of the first sacral vertebra - iliac wing angle, sacropubic angle and acetabular version. In exstrophy, the angles demonstrate opening of the iliac wings and the pubic ramus, and acetabular retroversion compared to controls. Comparisons between controls, continent and incontinent patients reveal that in continent patients, APD increases with growth and seems to be a predictive criterion for continence, independent of diastasis of the pubic symphysis. We believe that CT of the pelvis with measurements of the APD should be performed in all neonates with bladder exstrophy before reconstructive surgery and for better understanding of the malformation. The APD seems to be predictive and may be a major criterion for continence, independent of PD. (orig.)

  9. Focused information criterion and model averaging based on weighted composite quantile regression

    KAUST Repository

    Xu, Ganggang

    2013-08-13

    We study the focused information criterion and frequentist model averaging and their application to post-model-selection inference for weighted composite quantile regression (WCQR) in the context of the additive partial linear models. With the non-parametric functions approximated by polynomial splines, we show that, under certain conditions, the asymptotic distribution of the frequentist model averaging WCQR-estimator of a focused parameter is a non-linear mixture of normal distributions. This asymptotic distribution is used to construct confidence intervals that achieve the nominal coverage probability. With properly chosen weights, the focused information criterion based WCQR estimators are not only robust to outliers and non-normal residuals but also can achieve efficiency close to the maximum likelihood estimator, without assuming the true error distribution. Simulation studies and a real data analysis are used to illustrate the effectiveness of the proposed procedure. © 2013 Board of the Foundation of the Scandinavian Journal of Statistics..

  10. Corrections to the Eckhaus' stability criterion for one-dimensional stationary structures

    Science.gov (United States)

    Malomed, B. A.; Staroselsky, I. E.; Konstantinov, A. B.

    1989-01-01

    Two amendments to the well-known Eckhaus' stability criterion for small-amplitude non-linear structures generated by weak instability of a spatially uniform state of a non-equilibrium one-dimensional system against small perturbations with finite wavelengths are obtained. Firstly, we evaluate small corrections to the main Eckhaus' term which, on the contrary so that term, do not have a universal form. Comparison of those non-universal corrections with experimental or numerical results gives a possibility to select a more relevant form of an effective nonlinear evolution equation. In particular, the comparison with such results for convective rolls and Taylor vortices gives arguments in favor of the Swift-Hohenberg equation. Secondly, we derive an analog of the Eckhaus criterion for systems degenerate in the sense that in an expansion of their non-linear parts in powers of dynamical variables, the second and third degree terms are absent.

  11. Added value of cerebro-placental ratio and uterine artery Doppler at routine third trimester screening as a predictor of SGA and FGR in non-selected pregnancies.

    Science.gov (United States)

    Rial-Crestelo, M; Martinez-Portilla, R J; Cancemi, A; Caradeux, J; Fernandez, L; Peguero, A; Gratacos, E; Figueras, Francesc

    2018-03-04

    The objective of this study is to determine the added value of cerebroplacental ratio (CPR) and uterine Doppler velocimetry at third trimester scan in an unselected obstetric population to predict smallness and growth restriction. We constructed a prospective cohort study of women with singleton pregnancies attended for routine third trimester screening (32 +0 -34 +6 weeks). Fetal biometry and fetal-maternal Doppler ultrasound examinations were performed by certified sonographers. The CPR was calculated as a ratio of the middle cerebral artery to the umbilical artery pulsatility indices. Both attending professionals and patients were blinded to the results, except in cases of estimated fetal weight < p10. The association between third trimester Doppler parameters and small for gestational age (SGA) (birth weight <10th centile) and fetal growth restriction (FGR) (birth weight below the third centile) was assessed by logistic regression, where the basal comparison was a model comprising maternal characteristics and estimated fetal weight (EFW). A total of 1030 pregnancies were included. The mean gestational age at scan was 33 weeks (SD 0.6). The addition of CPR and uterine Doppler to maternal characteristics plus EFW improved the explained uncertainty of the predicting models for SGA (15 versus 10%, p < .001) and FGR (12 versus 8%, p = .03). However, the addition of CPR and uterine Doppler to maternal characteristics plus EFW only marginally improved the detection rates for SGA (38 versus 34% for a 10% of false positives) and did not change the predictive performance for FGR. The added value of CPR and uterine Doppler at 33 weeks of gestation for detecting defective growth is poor.

  12. Induced Effects on Red Imported Fire Ant (Hymenoptera: Formicidae) Forager Size Ratios by Pseudacteon spp. (Diptera: Phoridae): Implications on Bait Size Selection.

    Science.gov (United States)

    Reed, J J; Puckett, R T; Gold, R E

    2015-10-01

    Red imported fire ants, Solenopsis invicta Buren, are adversely affected by phorid flies in the genus Pseudacteon by instigating defensive behaviors in their hosts, and in turn reducing the efficiency of S. invicta foraging. Multiple Pseudacteon species have been released in Texas, and research has been focused on the establishment and spread of these introduced biological control agents. Field experiments were conducted to determine bait particle size selection of S. invicta when exposed to phorid populations. Four different particle sizes of two candidate baits were offered to foragers (one provided by a pesticide manufacturer, and a laboratory-created bait). Foragers selectively were attracted to, and removed more 1-1.4-mm particles than any other bait size. The industry-provided bait is primarily made of particles in the 1.4-2.0 mm size, larger than what was selected by the ants in this study. While there was a preference for foragers to be attracted to and rest on the industry-provided blank bait, S. invicta removed more of the laboratory-created bait from the test vials. There was an abundance of workers with head widths ranging from 0.5-0.75 mm collected from baits. This was dissimilar from a previous study wherein phorid flies were not active and in which large workers were collected in higher abundance at the site. This implies that phorid fly activity caused a shift for red imported fire ant colonies to have fewer large foragers. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. External and Internal Citation Analyses Can Provide Insight into Serial/Monograph Ratios when Refining Collection Development Strategies in Selected STEM Disciplines

    Directory of Open Access Journals (Sweden)

    Stephanie Krueger

    2016-12-01

    Full Text Available A Review of: Kelly, M. (2015. Citation patterns of engineering, statistics, and computer science researchers: An internal and external citation analysis across multiple engineering subfields. College and Research Libraries, 76(7, 859-882. http://doi.org/10.5860/crl.76.7.859 Objective – To determine internal and external citation analysis methods and their potential applicability to the refinement of collection development strategies at both the institutional and cross-institutional levels for selected science, technology, engineering, and mathematics (STEM subfields. Design – Multidimensional citation analysis; specifically, analysis of citations from 1 key scholarly journals in selected STEM subfields (external analysis compared to those from 2 local doctoral dissertations in similar subfields (internal analysis. Setting – Medium-sized, STEM-dominant public research university in the United States of America. Subjects – Two citation datasets: 1 14,149 external citations from16 journals (i.e., 2 journals per subfield; citations from 2012 volumes representing bioengineering, civil engineering, computer science (CS, electrical engineering, environmental engineering, operations research, statistics (STAT, and systems engineering; and 2 8,494 internal citations from 99 doctoral dissertations (18-22 per subfield published between 2008-–2012 from CS, electrical and computer engineering (ECE, and applied information technology (AIT and published between 2005-–2012 for systems engineering and operations research (SEOR and STAT. Methods – Citations, including titles and publication dates, were harvested from source materials and stored in Excel and then manually categorized according to format (book, book chapter, journal, conference proceeding, website, and several others. To analyze citations, percentages of occurrence by subfield were calculated for variables including format, age (years since date cited, journal distribution, and the

  14. Fischer-Tropsch Synthesis: Influence of CO Conversion on Selectivities H2/CO Usage Ratios and Catalyst Stability for a 0.27 percent Ru 25 percent Co/Al2O3 using a Slurry Phase Reactor

    Energy Technology Data Exchange (ETDEWEB)

    W Ma; G Jacobs; Y Ji; T Bhatelia; D Bukur; S Khalid; B Davis

    2011-12-31

    The effect of CO conversion on hydrocarbon selectivities (i.e., CH{sub 4}, C{sub 5+}, olefin and paraffin), H{sub 2}/CO usage ratios, CO{sub 2} selectivity, and catalyst stability over a wide range of CO conversion (12-94%) on 0.27%Ru-25%Co/Al{sub 2}O{sub 3} catalyst was studied under the conditions of 220 C, 1.5 MPa, H{sub 2}/CO feed ratio of 2.1 and gas space velocities of 0.3-15 NL/g-cat/h in a 1-L continuously stirred tank reactor (CSTR). Catalyst samples were withdrawn from the CSTR at different CO conversion levels, and Co phases (Co, CoO) in the slurry samples were characterized by XANES, and in the case of the fresh catalysts, EXAFS as well. Ru was responsible for increasing the extent of Co reduction, thus boosting the active site density. At 1%Ru loading, EXAFS indicates that coordination of Ru at the atomic level was virtually solely with Co. It was found that the selectivities to CH{sub 4}, C{sub 5+}, and CO{sub 2} on the Co catalyst are functions of CO conversion. At high CO conversions, i.e. above 80%, CH{sub 4} selectivity experienced a change in the trend, and began to increase, and CO{sub 2} selectivity experienced a rapid increase. H{sub 2}/CO usage ratio and olefin content were found to decrease with increasing CO conversion in the range of 12-94%. The observed results are consistent with water reoxidation of Co during FTS at high conversion. XANES spectroscopy of used catalyst samples displayed spectra consistent with the presence of more CoO at higher CO conversion levels.

  15. Prediction of Hot Tearing Using a Dimensionless Niyama Criterion

    Science.gov (United States)

    Monroe, Charles; Beckermann, Christoph

    2014-08-01

    The dimensionless form of the well-known Niyama criterion is extended to include the effect of applied strain. Under applied tensile strain, the pressure drop in the mushy zone is enhanced and pores grow beyond typical shrinkage porosity without deformation. This porosity growth can be expected to align perpendicular to the applied strain and to contribute to hot tearing. A model to capture this coupled effect of solidification shrinkage and applied strain on the mushy zone is derived. The dimensionless Niyama criterion can be used to determine the critical liquid fraction value below which porosity forms. This critical value is a function of alloy properties, solidification conditions, and strain rate. Once a dimensionless Niyama criterion value is obtained from thermal and mechanical simulation results, the corresponding shrinkage and deformation pore volume fractions can be calculated. The novelty of the proposed method lies in using the critical liquid fraction at the critical pressure drop within the mushy zone to determine the onset of hot tearing. The magnitude of pore growth due to shrinkage and deformation is plotted as a function of the dimensionless Niyama criterion for an Al-Cu alloy as an example. Furthermore, a typical hot tear "lambda"-shaped curve showing deformation pore volume as a function of alloy content is produced for two Niyama criterion values.

  16. New Quality Assessment Criterion of AlSi5Cu1 Alloy

    Directory of Open Access Journals (Sweden)

    M. Wierzbińska

    2007-07-01

    Full Text Available The paper presents the discussion of the results of mechanical testing for aluminium foundry alloy AlSi5Cu1Mg for high-loaded machine elements. Values of yield strength (Rp0.2, tensile strength (Rm, elongation(A5 and hardness (HB are usually considered as the primary quality assessment criterion for a manufacturing process. It was concluded, that this criterion, A5 index particularly, is unsatisfactory to estimate the plasticity of the alloy and its crack resistance in the presence of sharp-pointed stress concentrators or microcracks. More adequate parameter is plane strain fracture toughness KIc. However, size of the samples appeared to be twice as large as would be needed to fulfill requirements of test conditions, and the test itself is laborious and time-consuming that it becomes impractical as a acceptance test. Therefore, substitute test for quality assessment – determination of tensile strength in the presence of a sharp notch kmR was applied. The comparative analysis of kmR/Rp0.2 ratio, as a more enhanced fatigue resistance criterion than kmR and plane strain fracture toughness KIc of the alloy was performed. It was assumed that kmR/Rp0.2 parameter has good correlation with the critical stress intensity factor KIc Thus, under manufacturing process conditions, being unable to carry out KIc test, it may be successfully replaced by kmR test.

  17. The precautionary principle as a rational decision criterion

    International Nuclear Information System (INIS)

    Hovi, Jon

    2001-12-01

    The paper asks if the precautionary principle may be seen as a rational decision criterion. Six main questions are discussed. 1. Does the principle basically represent a particular set of political options or is it a genuine decision criterion? 2. If it is the latter, can it be reduced to any of the existing criteria for decision making under uncertainty? 3. In what kinds of situation is the principle applicable? 4. What is the relation between the precautionary principle and other principles for environmental regulation? 5. How plausible is the principle's claim that the burden of proof should be reversed? 6. Do the proponents of environmental regulation carry no burden of proof at all? A main conclusion is that, for now at least, the principle contains too many unclear elements to satisfy the requirements of precision and consistency that should reasonably be satisfied by a rational decision criterion. (author)

  18. Study on the quantitative rod internal pressure design criterion

    International Nuclear Information System (INIS)

    Kim, Kyu Tae; Kim, Oh Hwan; Han, Hee Tak

    1991-01-01

    The current rod internal pressure criterion permits fuel rods to operate with internal pressures in excess of system pressure only if internal overpressure does not cause the diametral gap enlargement. In this study, the generic allowable internal gas pressure not violating this criterion is estimated as a function of rod power. The results show that the generic allowable internal gas pressure decreases linearly with the increase of rod power. Application of the generic allowable internal gas pressure for the rod internal pressure design criterion will result in the simplication of the current design procedure for checking the diametral gap enlargement caused by internal overpressure because according to the current design procedure the cladding creepout rate should be compared with the fuel swelling rate at each axial node at each time step whenever internal pressure exceeds the system pressure. (Author)

  19. Development of failure criterion for Kevlar-epoxy fabric laminates

    Science.gov (United States)

    Tennyson, R. C.; Elliott, W. G.

    1984-01-01

    The development of the tensor polynomial failure criterion for composite laminate analysis is discussed. In particular, emphasis is given to the fabrication and testing of Kevlar-49 fabric (Style 285)/Narmco 5208 Epoxy. The quadratic-failure criterion with F(12)=0 provides accurate estimates of failure stresses for the Kevlar/Epoxy investigated. The cubic failure criterion was re-cast into an operationally easier form, providing the engineer with design curves that can be applied to laminates fabricated from unidirectional prepregs. In the form presented no interaction strength tests are required, although recourse to the quadratic model and the principal strength parameters is necessary. However, insufficient test data exists at present to generalize this approach for all undirectional prepregs and its use must be restricted to the generic materials investigated to-date.

  20. A Joint Optimization Criterion for Blind DS-CDMA Detection

    Directory of Open Access Journals (Sweden)

    Sergio A. Cruces-Alvarez

    2007-01-01

    Full Text Available This paper addresses the problem of the blind detection of a desired user in an asynchronous DS-CDMA communications system with multipath propagation channels. Starting from the inverse filter criterion introduced by Tugnait and Li in 2001, we propose to tackle the problem in the context of the blind signal extraction methods for ICA. In order to improve the performance of the detector, we present a criterion based on the joint optimization of several higher-order statistics of the outputs. An algorithm that optimizes the proposed criterion is described, and its improved performance and robustness with respect to the near-far problem are corroborated through simulations. Additionally, a simulation using measurements on a real software-radio platform at 5 GHz has also been performed.

  1. A Joint Optimization Criterion for Blind DS-CDMA Detection

    Science.gov (United States)

    Durán-Díaz, Iván; Cruces-Alvarez, Sergio A.

    2006-12-01

    This paper addresses the problem of the blind detection of a desired user in an asynchronous DS-CDMA communications system with multipath propagation channels. Starting from the inverse filter criterion introduced by Tugnait and Li in 2001, we propose to tackle the problem in the context of the blind signal extraction methods for ICA. In order to improve the performance of the detector, we present a criterion based on the joint optimization of several higher-order statistics of the outputs. An algorithm that optimizes the proposed criterion is described, and its improved performance and robustness with respect to the near-far problem are corroborated through simulations. Additionally, a simulation using measurements on a real software-radio platform at 5 GHz has also been performed.

  2. The role of word choice and criterion on intentional memory.

    Science.gov (United States)

    Toyota, Hiroshi

    2015-02-01

    The relationship between the criterion for choosing and the self-choice effects (greater recall in a self-choice compared to a forced-choice condition) on intentional memory was examined. Thirty-three female nursing school volunteers were administered 24 word pairs in a 2 × 2 design to assess the influence of motivation upon free recall. When word pairs were presented to participants, they were asked to choose a word to-be-remembered, either in a self-choice condition or a forced-choice condition. Words chosen by the participants were recalled more often than those chosen by the experimenter (forced choice). Thus, the self-choice effect was greater for words chosen with a self-reference criterion compared to a metamemory criterion, supporting the integration hypothesis as the origin of the self-choice effect.

  3. SOCIO-PSYCHOLOGICAL CRITERIONS OF FAMILY LIFESTYLE TYPOLOGY

    Directory of Open Access Journals (Sweden)

    Yekaterina Anatolievna Yumkina

    2015-02-01

    Full Text Available The purpose of this article is to present socio-psychological criterions of family lifestyle typology, which were found during theoretical modelling and empirical research work. It is important in fundamental and practical aspects. St-Petersburg students (n = 116, from 19 to 21 years old were examined by special questionnaire «Family relationship and home» (Kunitsi-na V.N., Yumkina Ye.A., 2012 which measures different aspects of family lifestyle. We also used complex of methods that gave us information about personal values, self-rating and parent-child relationships. Dates were divided into six groups according to three main criterions of family lifestyle typology: social environment of family life, family activity, and family interpersonal relationships. There were found statistically significant differences between pairs of group from every criterions. The results can be useful in spheres dealing with family crisis, family development, family traditions etc.

  4. Probabilistic interpretation of the reduction criterion for entanglement

    International Nuclear Information System (INIS)

    Zhang, Zhengmin; Luo, Shunlong

    2007-01-01

    Inspired by the idea of conditional probabilities, we introduce a variant of conditional density operators. But unlike the conditional probabilities which are bounded by 1, the conditional density operators may have eigenvalues exceeding 1 for entangled states. This has the consequence that although any bivariate classical probability distribution has a natural separable decomposition in terms of conditional probabilities, we do not have a quantum analogue of this separable decomposition in general. The 'nonclassical' eigenvalues of conditional density operators are indications of entanglement. The resulting separability criterion turns out to be equivalent to the reduction criterion introduced by Horodecki [Phys. Rev. A 59, 4206 (1999)] and Cerf et al. [Phys. Rev. A 60, 898 (1999)]. This supplies an intuitive probabilistic interpretation for the reduction criterion. The conditional density operators are also used to define a form of quantum conditional entropy which provides an alternative mechanism to reveal quantum discord

  5. Solid/liquid partition coefficients (K{sub d}) and plant/soil concentration ratios (CR) for selected soils, tills and sediments at Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Sheppard, Steve (ECOMatters Inc. (Canada)); Sohlenius, Gustav (Sveriges geologiska undersoekning (Sweden)); Omberg, Lars-Gunnar (ALS Scandinavia AB (Sweden)); Borgiel, Mikael (Sveriges Vattenekologer AB (Sweden)); Grolander, Sara (Facilia AB (Sweden)); Norden, Sara (Svensk Kaernbraenslehantering AB (Sweden))

    2011-11-15

    Solid/liquid partition coefficients (K{sub d}) are used to indicate the relative mobility of radionuclides and elements of concern from nuclear fuel waste, as well as from other sources. To indicate the uptake of radionuclides in biota concentration ratios (CR) between soil and biota are used. This report summarized K{sub d} data for regolith and marine sediments based on concentrations of 69 indigenous stable elements measured from samples collected at the Forsmark site and CR data concerning cereals growing on these soils. The samples included 50 regolith samples from agricultural land and wetlands, 8 samples of till collected at different depths, and two marine sediment samples. In addition, cereal grains, stems and roots were collected from 4 sites for calculation of CRs. The regolith samples represented the major 5 deposits, which can be used as arable land, at the site (clayey till, glacial clay, clay gyttja and peat (cultivated and undisturbed)). K{sub d} values were generally lower for peat compared to clay soils. There were also clear differences in K{sub d} resulting from differences in soil chemistry within each regolith type. Soil pH was the most important factor, and K{sub d} values for many elements were lower in acidic clay soils compared to basic clay soils. Although there were only a few samples of sandy till and marine sediment, the K{sub d} values were generally consistent with the corresponding regolith K{sub d} values. Of the different cereal parts the grain always had the lowest CR. In most cases, the root CR was significantly higher than the grain CR, whereas only for a few elements were the grain and stem CR values different

  6. Solid/liquid partition coefficients (Kd) and plant/soil concentration ratios (CR) for selected soils, tills and sediments at Forsmark

    International Nuclear Information System (INIS)

    Sheppard, Steve; Sohlenius, Gustav; Omberg, Lars-Gunnar; Borgiel, Mikael; Grolander, Sara; Norden, Sara

    2011-11-01

    Solid/liquid partition coefficients (K d ) are used to indicate the relative mobility of radionuclides and elements of concern from nuclear fuel waste, as well as from other sources. To indicate the uptake of radionuclides in biota concentration ratios (CR) between soil and biota are used. This report summarized K d data for regolith and marine sediments based on concentrations of 69 indigenous stable elements measured from samples collected at the Forsmark site and CR data concerning cereals growing on these soils. The samples included 50 regolith samples from agricultural land and wetlands, 8 samples of till collected at different depths, and two marine sediment samples. In addition, cereal grains, stems and roots were collected from 4 sites for calculation of CRs. The regolith samples represented the major 5 deposits, which can be used as arable land, at the site (clayey till, glacial clay, clay gyttja and peat (cultivated and undisturbed)). K d values were generally lower for peat compared to clay soils. There were also clear differences in K d resulting from differences in soil chemistry within each regolith type. Soil pH was the most important factor, and K d values for many elements were lower in acidic clay soils compared to basic clay soils. Although there were only a few samples of sandy till and marine sediment, the K d values were generally consistent with the corresponding regolith K d values. Of the different cereal parts the grain always had the lowest CR. In most cases, the root CR was significantly higher than the grain CR, whereas only for a few elements were the grain and stem CR values different

  7. Criterion-based laparoscopic training reduces total training time

    OpenAIRE

    Brinkman, Willem M.; Buzink, Sonja N.; Alevizos, Leonidas; de Hingh, Ignace H. J. T.; Jakimowicz, Jack J.

    2011-01-01

    Introduction The benefits of criterion-based laparoscopic training over time-oriented training are unclear. The purpose of this study is to compare these types of training based on training outcome and time efficiency. Methods During four training sessions within 1 week (one session per day) 34 medical interns (no laparoscopic experience) practiced on two basic tasks on the Simbionix LAP Mentor virtual-reality (VR) simulator: ‘clipping and grasping’ and ‘cutting’. Group C (criterion-based) (N...

  8. Bell's theorem based on a generalized EPR criterion of reality

    International Nuclear Information System (INIS)

    Eberhard, P.H.; Rosselet, P.

    1995-01-01

    First, the demonstration of Bell's theorem, i.e., of the nonlocal character of quantum theory, is spelled out using the EPR criterion of reality as premises and a gedanken experiment involving two particles. Then, the EPR criterion is extended to include quantities predicted almost with certainty, and Bell's theorem is demonstrated on these new premises. The same experiment is used but in conditions that become possible in real life, without the requirements of ideal efficiencies and zero background. Very high efficiencies and low background are needed, but these requirements may be met in the future

  9. Bell's theorem based on a generalized EPR criterion of reality

    International Nuclear Information System (INIS)

    Eberhard, P.H.; Rosselet, P.

    1993-04-01

    First, the demonstration of Bell's theorem, i.e. of the non-local character of quantum theory, is spelled out using the EPR criterion of reality as premises and a gedanken experiment involving two particles. Then, the EPR criterion is extended to include quantities predicted almost with certainty, and Bell's theorem is demonstrated on these new premises. The same experiment is used but in conditions that become possible in real life, without the requirements of ideal efficiencies and zero background. Very high efficiencies and low background are needed, but these requirements may be met in the future. (author) 1 fig., 11 refs

  10. Quantitative Lesion-to-Fat Elasticity Ratio Measured by Shear-Wave Elastography for Breast Mass: Which Area Should Be Selected as the Fat Reference?

    Science.gov (United States)

    Youk, Ji Hyun; Son, Eun Ju; Gweon, Hye Mi; Han, Kyung Hwa; Kim, Jeong-Ah

    2015-01-01

    To investigate whether the diagnostic performance of lesion-to-fat elasticity ratio (Eratio) was affected by the location of the reference fat. For 257 breast masses in 250 women who underwent shear-wave elastography before biopsy or surgery, multiple Eratios were measured with a fixed region-of-interest (ROI) in the mass along with multiple ROIs over the surrounding fat in different locations. Logistic regression analysis was used to determine that Eratio was independently associated with malignancy adjusted for the location of fat ROI (depth, laterality, and distance from lesion or skin). Mean (Emean) and maximum (Emax) elasticity values of fat were divided into four groups according to their interquartile ranges. Diagnostic performance of each group was evaluated using the area under the ROC curve (AUC). False diagnoses of Eratio were reviewed for ROIs on areas showing artifactual high or low stiffness and analyzed by logistic regression analysis to determine variables (associated palpable abnormality, lesion size, the vertical distance from fat ROI to skin, and elasticity values of lesion or fat) independently associated with false results. Eratio was independently associated with malignancy adjusted for the location of fat ROI (P<0.0001). Among four groups of fat elasticity values, the AUC showed no significant difference (<25th percentile, 25th percentile~median, median~75th percentile, and ≥75th percentile; 0.973, 0.982, 0.967, and 0.954 for Emean; 0.977, 0.967, 0.966, and 0.957 for Emax). Fat elasticity values were independently associated with false results of Eratio with the cut-off of 3.18 from ROC curve (P<0.0001). ROIs were set on fat showing artifactual high stiffness in 90% of 10 false negatives and on lesion showing vertical striped artifact or fat showing artifactual low stiffness in 77.5% of 71 false positives. Eratio shows good diagnostic performance regardless of the location of reference fat, except when it is placed in areas of artifacts.

  11. Quantitative Lesion-to-Fat Elasticity Ratio Measured by Shear-Wave Elastography for Breast Mass: Which Area Should Be Selected as the Fat Reference?

    Directory of Open Access Journals (Sweden)

    Ji Hyun Youk

    Full Text Available To investigate whether the diagnostic performance of lesion-to-fat elasticity ratio (Eratio was affected by the location of the reference fat.For 257 breast masses in 250 women who underwent shear-wave elastography before biopsy or surgery, multiple Eratios were measured with a fixed region-of-interest (ROI in the mass along with multiple ROIs over the surrounding fat in different locations. Logistic regression analysis was used to determine that Eratio was independently associated with malignancy adjusted for the location of fat ROI (depth, laterality, and distance from lesion or skin. Mean (Emean and maximum (Emax elasticity values of fat were divided into four groups according to their interquartile ranges. Diagnostic performance of each group was evaluated using the area under the ROC curve (AUC. False diagnoses of Eratio were reviewed for ROIs on areas showing artifactual high or low stiffness and analyzed by logistic regression analysis to determine variables (associated palpable abnormality, lesion size, the vertical distance from fat ROI to skin, and elasticity values of lesion or fat independently associated with false results.Eratio was independently associated with malignancy adjusted for the location of fat ROI (P<0.0001. Among four groups of fat elasticity values, the AUC showed no significant difference (<25th percentile, 25th percentile~median, median~75th percentile, and ≥75th percentile; 0.973, 0.982, 0.967, and 0.954 for Emean; 0.977, 0.967, 0.966, and 0.957 for Emax. Fat elasticity values were independently associated with false results of Eratio with the cut-off of 3.18 from ROC curve (P<0.0001. ROIs were set on fat showing artifactual high stiffness in 90% of 10 false negatives and on lesion showing vertical striped artifact or fat showing artifactual low stiffness in 77.5% of 71 false positives.Eratio shows good diagnostic performance regardless of the location of reference fat, except when it is placed in areas of

  12. Optimal order and time-step criterion for Aarseth-type N-body integrators

    International Nuclear Information System (INIS)

    Makino, Junichiro

    1991-01-01

    How the selection of the time-step criterion and the order of the integrator change the efficiency of Aarseth-type N-body integrators is discussed. An alternative to Aarseth's scheme based on the direct calculation of the time derivative of the force using the Hermite interpolation is compared to Aarseth's scheme, which uses the Newton interpolation to construct the predictor and corrector. How the number of particles in the system changes the behavior of integrators is examined. The Hermite scheme allows a time step twice as large as that for the standard Aarseth scheme for the same accuracy. The calculation cost of the Hermite scheme per time step is roughly twice as much as that of the standard Aarseth scheme. The optimal order of the integrators depends on both the particle number and the accuracy required. The time-step criterion of the standard Aarseth scheme is found to be inapplicable to higher-order integrators, and a more uniformly reliable criterion is proposed. 18 refs

  13. Cost overruns and demand shortfalls - Deception or selection?

    DEFF Research Database (Denmark)

    Eliasson, Jonas; Fosgerau, Mogens

    2013-01-01

    whether to implement projects. Using a database of projects we present examples indicating that the selection bias may be substantial. The examples also indicate that benefit-cost ratios remain a useful selection criterion even when cost and benefits are highly uncertain, gainsaying the argument......A number of highly cited papers by Flyvbjerg and associates have shown that ex ante infrastructure appraisals tend to be overly optimistic. Ex post evaluations indicate a bias where investment costs are higher and benefits lower on average than predicted ex ante. These authors argue that the bias...... that such uncertainties render cost-benefit analyses useless. © 2013 Elsevier Ltd....

  14. Blind deblurring of spiral CT images - comparative studies on edge-to-noise ratios

    International Nuclear Information System (INIS)

    Jiang Ming; Wan Ge; Skinner, Margaret W.; Rubinstein, Jay T.; Vannier, Michael W.

    2002-01-01

    A recently developed blind deblurring algorithm based on the edge-to-noise ratio has been applied to improve the quality of spiral CT images. Since the discrepancy measure used to quantify the edge and noise effects is not symmetric, there are several ways to formulate the edge-to-noise ratio. This article is to investigate the performance of those ratios with phantom and patient data. In the phantom study, it is shown that all the ratios share similar properties, validating the blind deblurring algorithm. The image fidelity improvement varies from 29% to 33% for different ratios, according to the root mean square error (RMSE) criterion; the optimal iteration number determined for each ratio varies from 25 to 35. Those ratios that are associated with most satisfactory performance are singled out for the image fidelity improvement of about 33% in the numerical simulation. After automatic blind deblurring with the selected ratios, the spatial resolution of CT is substantially refined in all the cases tested

  15. A Criterion-Referenced Approach to Student Ratings of Instruction

    Science.gov (United States)

    Meyer, J. Patrick; Doromal, Justin B.; Wei, Xiaoxin; Zhu, Shi

    2017-01-01

    We developed a criterion-referenced student rating of instruction (SRI) to facilitate formative assessment of teaching. It involves four dimensions of teaching quality that are grounded in current instructional design principles: Organization and structure, Assessment and feedback, Personal interactions, and Academic rigor. Using item response…

  16. Short-Cut Estimators of Criterion-Referenced Test Consistency.

    Science.gov (United States)

    Brown, James Dean

    1990-01-01

    Presents simplified methods for deriving estimates of the consistency of criterion-referenced, English-as-a-Second-Language tests, including (1) the threshold loss agreement approach using agreement or kappa coefficients, (2) the squared-error loss agreement approach using the phi(lambda) dependability approach, and (3) the domain score…

  17. Decision models for use with criterion-referenced tests

    NARCIS (Netherlands)

    van der Linden, Willem J.

    1980-01-01

    The problem of mastery decisions and optimizing cutoff scores on criterion-referenced tests is considered. This problem can be formalized as an (empirical) Bayes problem with decisions rules of a monotone shape. Next, the derivation of optimal cutoff scores for threshold, linear, and normal ogive

  18. Criterion-based laparoscopic training reduces total training time

    NARCIS (Netherlands)

    Brinkman, W.M.; Buzink, S.N.; Alevizos, L.; De Hingh, I.H.J.T.; Jakimowicz, J.J.

    2011-01-01

    The benefits of criterion-based laparoscopic training over time-oriented training are unclear. The purpose of this study is to compare these types of training based on training outcome and time efficiency. Methods During four training sessions within 1 week (one session per day) 34 medical interns

  19. Electronics. Criterion-Referenced Test (CRT) Item Bank.

    Science.gov (United States)

    Davis, Diane, Ed.

    This document contains 519 criterion-referenced multiple choice and true or false test items for a course in electronics. The test item bank is designed to work with both the Vocational Instructional Management System (VIMS) and the Vocational Administrative Management System (VAMS) in Missouri. The items are grouped into 15 units covering the…

  20. Prioritising transport infrastructure projects: towards a multi-criterion ...

    African Journals Online (AJOL)

    Kirstam

    multi-criterion analysis (MCA), partial equilibrium analysis, project appraisal ... In the case of transport infrastructure projects, though, this is no mean ... vehicle ownership and mileage-based depreciation (an improved road network and/ .... urban, rural or regional development initiatives – they typically include one or more.

  1. Slope stability analysis using limit equilibrium method in nonlinear criterion.

    Science.gov (United States)

    Lin, Hang; Zhong, Wenwen; Xiong, Wei; Tang, Wenyu

    2014-01-01

    In slope stability analysis, the limit equilibrium method is usually used to calculate the safety factor of slope based on Mohr-Coulomb criterion. However, Mohr-Coulomb criterion is restricted to the description of rock mass. To overcome its shortcomings, this paper combined Hoek-Brown criterion and limit equilibrium method and proposed an equation for calculating the safety factor of slope with limit equilibrium method in Hoek-Brown criterion through equivalent cohesive strength and the friction angle. Moreover, this paper investigates the impact of Hoek-Brown parameters on the safety factor of slope, which reveals that there is linear relation between equivalent cohesive strength and weakening factor D. However, there are nonlinear relations between equivalent cohesive strength and Geological Strength Index (GSI), the uniaxial compressive strength of intact rock σ ci , and the parameter of intact rock m i . There is nonlinear relation between the friction angle and all Hoek-Brown parameters. With the increase of D, the safety factor of slope F decreases linearly; with the increase of GSI, F increases nonlinearly; when σ ci is relatively small, the relation between F and σ ci is nonlinear, but when σ ci is relatively large, the relation is linear; with the increase of m i , F decreases first and then increases.

  2. Numerical and Experimental Validation of a New Damage Initiation Criterion

    NARCIS (Netherlands)

    Sadhinoch, M.; Atzema, E.H.; Perdahcioglu, E.S.; Van Den Boogaard, A.H.

    2017-01-01

    Most commercial finite element software packages, like Abaqus, have a built-in coupled damage model where a damage evolution needs to be defined in terms of a single fracture energy value for all stress states. The Johnson-Cook criterion has been modified to be Lode parameter dependent and this

  3. Signal Detection with Criterion Noise: Applications to Recognition Memory

    Science.gov (United States)

    Benjamin, Aaron S.; Diaz, Michael; Wee, Serena

    2009-01-01

    A tacit but fundamental assumption of the theory of signal detection is that criterion placement is a noise-free process. This article challenges that assumption on theoretical and empirical grounds and presents the noisy decision theory of signal detection (ND-TSD). Generalized equations for the isosensitivity function and for measures of…

  4. Criterion III: Maintenance of rangeland productive capacity [Chapter 4

    Science.gov (United States)

    G. R. Evans; R. A. Washmgton-Allen; R. D. Child; J. E. Mitchell; B. R. Bobowskl; R. V. Loper; B. H. Allen-Diaz; D. W. Thompson; G. R. Welling; T. B. Reuwsaat

    2010-01-01

    Maintenance of rangeland productive capacity is one of five criteria established by the Sustainable Rangelands Roundtable (SRR) to monitor and assess rangeland sustainable management. Within this criterion, six indicators were developed through the Delphi Process and the expert opinions of academicians, rangeland scientists, rangeland management agency personnel, non-...

  5. Criterion of Semi-Markov Dependent Risk Model

    Institute of Scientific and Technical Information of China (English)

    Xiao Yun MO; Xiang Qun YANG

    2014-01-01

    A rigorous definition of semi-Markov dependent risk model is given. This model is a generalization of the Markov dependent risk model. A criterion and necessary conditions of semi-Markov dependent risk model are obtained. The results clarify relations between elements among semi-Markov dependent risk model more clear and are applicable for Markov dependent risk model.

  6. An Elementary Proof of a Criterion for Linear Disjointness

    Science.gov (United States)

    Dobbs, David E.

    2013-01-01

    An elementary proof using matrix theory is given for the following criterion: if "F"/"K" and "L"/"K" are field extensions, with "F" and "L" both contained in a common extension field, then "F" and "L" are linearly disjoint over "K" if (and only if) some…

  7. Utilization of Durability Criterion to Develop Automotive Components

    DEFF Research Database (Denmark)

    Ricardo, Luiz Carlos Hernandes

    2010-01-01

    Today the automotive companies must reduce the time to development of new products with improvement in performance, durability and low cost reductions where possible. To achieve this goal the carmakers need to improve the design criterion of car systems like body, chassis and suspension component...

  8. Botanical Criterions of Quchan Baharkish pastureland in Khorasan ...

    African Journals Online (AJOL)

    ADOWIE PERE

    Botanical Criterions of Quchan Baharkish pastureland in Khorasan Razavi Province,. Iran. *1SAEED, JAHEDI POUR 2ALIREZA, KOOCHEKI 3MEHDI, NASSIRI. MAHALLATI 4PARVIZ REZVANI MOGHADDAM. 1Department of Agroecology and Plant Breeding, Ferdowsi. University of Mashhad International Campus, ...

  9. Satisfying the Einstein-Podolsky-Rosen criterion with massive particles

    DEFF Research Database (Denmark)

    Peise, Jan; Kruse, I.; Lange, K.

    2016-01-01

    In 1935, Einstein, Podolsky and Rosen (EPR) questioned the completeness of quantum mechanics by devising a quantum state of two massive particles with maximally correlated space and momentum coordinates. The EPR criterion qualifies such continuous-variable entangled states, as shown successfully...

  10. Generalized Bohm’s criterion and negative anode voltage fall in electric discharges

    Energy Technology Data Exchange (ETDEWEB)

    Londer, Ya. I.; Ul’yanov, K. N., E-mail: kulyanov@vei.ru [Lenin All-Russian Electrotechnical Institute (Russian Federation)

    2013-10-15

    The value of the voltage fall across the anode sheath is found as a function of the current density. Analytic solutions are obtained in a wide range of the ratio of the directed velocity of plasma electrons v{sub 0} to their thermal velocity v{sub T}. It is shown that the voltage fall in a one-dimensional collisionless anode sheath is always negative. At the small values of v{sub 0}/v{sub T}, the obtained expression asymptotically transforms into the Langmuir formula. Generalized Bohm’s criterion for an electric discharge with allowance for the space charge density ρ(0), electric field E(0), ion velocity v{sub i}(0), and ratio v{sub 0}/v{sub T} at the plasma-sheath interface is formulated. It is shown that the minimum value of the ion velocity v{sub i}{sup *}(0) corresponds to the vanishing of the electric field at one point inside the sheath. The dependence of v{sub i}{sup *} (0) on ρ(0), E(0), and v{sub 0}/v{sub T} determines the boundary of the existence domain of stationary solutions in the sheath. Using this criterion, the maximum possible degree of contraction of the electron current at the anode is determined for a short high-current vacuum arc discharge.

  11. Generalized Bohm’s criterion and negative anode voltage fall in electric discharges

    International Nuclear Information System (INIS)

    Londer, Ya. I.; Ul’yanov, K. N.

    2013-01-01

    The value of the voltage fall across the anode sheath is found as a function of the current density. Analytic solutions are obtained in a wide range of the ratio of the directed velocity of plasma electrons v 0 to their thermal velocity v T . It is shown that the voltage fall in a one-dimensional collisionless anode sheath is always negative. At the small values of v 0 /v T , the obtained expression asymptotically transforms into the Langmuir formula. Generalized Bohm’s criterion for an electric discharge with allowance for the space charge density ρ(0), electric field E(0), ion velocity v i (0), and ratio v 0 /v T at the plasma-sheath interface is formulated. It is shown that the minimum value of the ion velocity v i * (0) corresponds to the vanishing of the electric field at one point inside the sheath. The dependence of v i * (0) on ρ(0), E(0), and v 0 /v T determines the boundary of the existence domain of stationary solutions in the sheath. Using this criterion, the maximum possible degree of contraction of the electron current at the anode is determined for a short high-current vacuum arc discharge

  12. Assessing Local Model Adequacy in Bayesian Hierarchical Models Using the Partitioned Deviance Information Criterion

    Science.gov (United States)

    Wheeler, David C.; Hickson, DeMarc A.; Waller, Lance A.

    2010-01-01

    Many diagnostic tools and goodness-of-fit measures, such as the Akaike information criterion (AIC) and the Bayesian deviance information criterion (DIC), are available to evaluate the overall adequacy of linear regression models. In addition, visually assessing adequacy in models has become an essential part of any regression analysis. In this paper, we focus on a spatial consideration of the local DIC measure for model selection and goodness-of-fit evaluation. We use a partitioning of the DIC into the local DIC, leverage, and deviance residuals to assess local model fit and influence for both individual observations and groups of observations in a Bayesian framework. We use visualization of the local DIC and differences in local DIC between models to assist in model selection and to visualize the global and local impacts of adding covariates or model parameters. We demonstrate the utility of the local DIC in assessing model adequacy using HIV prevalence data from pregnant women in the Butare province of Rwanda during 1989-1993 using a range of linear model specifications, from global effects only to spatially varying coefficient models, and a set of covariates related to sexual behavior. Results of applying the diagnostic visualization approach include more refined model selection and greater understanding of the models as applied to the data. PMID:21243121

  13. Extra-electron induced covalent strengthening and generalization of intrinsic ductile-to-brittle criterion.

    Science.gov (United States)

    Niu, Haiyang; Chen, Xing-Qiu; Liu, Peitao; Xing, Weiwei; Cheng, Xiyue; Li, Dianzhong; Li, Yiyi

    2012-01-01

    Traditional strengthening ways, such as strain, precipitation, and solid-solution, come into effect by pinning the motion of dislocation. Here, through first-principles calculations we report on an extra-electron induced covalent strengthening mechanism, which alters chemical bonding upon the introduction of extra-valence electrons in the matrix of parent materials. It is responsible for the brittle and high-strength properties of Al(12)W-type compounds featured by the typical fivefold icosahedral cages, which are common for quasicrystals and bulk metallic glasses (BMGs). In combination with this mechanism, we generalize ductile-to-brittle criterion in a universal hyperbolic form by integrating the classical Pettifor's Cauchy pressure with Pugh's modulus ratio for a wide variety of materials with cubic lattices. This study provides compelling evidence to correlate Pugh's modulus ratio with hardness of materials and may have implication for understanding the intrinsic brittleness of quasicrystals and BMGs.

  14. Multi-Criterion Two-Sided Matching of Public–Private Partnership Infrastructure Projects: Criteria and Methods

    Directory of Open Access Journals (Sweden)

    Ru Liang

    2018-04-01

    Full Text Available Two kinds of evaluative criteria are associated with Public–Private Partnership (PPP infrastructure projects, i.e., private evaluative criteria and public evaluative criteria. These evaluative criteria are inversely related, that is, the higher the public benefits; the lower the private surplus. To balance evaluative criteria in the Two-Sided Matching (TSM decision, this paper develops a quantitative matching decision model to select an optimal matching scheme for PPP infrastructure projects based on the Hesitant Fuzzy Set (HFS under unknown evaluative criterion weights. In the model, HFS is introduced to describe values of the evaluative criteria and multi-criterion information is fully considered given by groups. The optimal model is built and solved by maximizing the whole deviation of each criterion so that the evaluative criterion weights are determined objectively. Then, the match-degree of the two sides is calculated and a multi-objective optimization model is introduced to select an optimal matching scheme via a min-max approach. The results provide new insights and implications of the influence on evaluative criteria in the TSM decision.

  15. Inter-laboratory comparison of elemental analysis and gas chromatography combustion isotope ratio mass spectrometry (GC-C-IRMS). Part I: delta13C measurements of selected compounds for the development of an isotopic Grob-test.

    Science.gov (United States)

    Serra, F; Janeiro, A; Calderone, G; Rojas, J M Moreno; Rhodes, C; Gonthier, L A; Martin, F; Lees, M; Mosandl, A; Sewenig, S; Hener, U; Henriques, B; Ramalho, L; Reniero, F; Teixeira, A J; Guillou, C

    2007-03-01

    This study was directed towards investigating suitable compounds to be used as stable isotope reference materials for gas chromatography combustion isotope ratio mass spectrometry (GC-C-IRMS) calibration. Several compounds were selected from those used in the 'Grob-test' mixture. Oxygen- and nitrogen-containing substances were added to these compounds to allow the mixture to be used as a possible multi-isotopic calibration tool for 2H/1H, 13C/12C, 15N/14N and 18O/16O ratio determinations. In this paper we present the results of delta13C measurements performed by the consortium of the five laboratories taking part in this inter-calibration exercise. All the compounds were individually assessed for homogeneity, short-term stability and long-term stability by means of EA-IRMS, as required by the bureau communitaire de reference (BCR) Guide for Production of Certified Reference Materials. The results were compared then with the GC-C-IRMS measurements using both polar and non-polar columns, and the final mixture of selected compounds underwent a further certification exercise assessing limits of accuracy and reproducibility under specified GC-C-IRMS conditions. Copyright 2007 John Wiley & Sons, Ltd.

  16. Jeans' criterion and nonextensive velocity distribution function in kinetic theory

    International Nuclear Information System (INIS)

    Du Jiulin

    2004-01-01

    The effect of nonextensivity of self-gravitating systems on the Jeans' criterion for gravitational instability is studied in the framework of Tsallis statistics. The nonextensivity is introduced in the Jeans problem by a generalized q-nonextensive velocity distribution function through the equation of state of ideal gas in nonextensive kinetic theory. A new Jeans' criterion is deduced with a factor √(2/(5-3q)) that, however, differs from that one in [Astron. Astrophys. 396 (2002) 309] and new results of gravitational instability are analyzed for the nonextensive parameter q. An understanding of physical meaning of q and a possible seismic observation to find astronomical evidence for a value of q different from unity are also discussed

  17. Logical and Decisive Combining Criterion for Binary Group Decision Making

    Directory of Open Access Journals (Sweden)

    Ivan Vrana

    2010-04-01

    Full Text Available A new combining criterion, the Multiplicative Proportional Deviative Influence (MPDI is presented for combining or aggregating multi-expert numerical judgments in Yes-or-No type ill-structured group decision making situations. This newly proposed criterion performs well in comparison with the widely used aggregation means: the Arithmetic Mean (AM, and Geometric Mean (GM, especially in better reflecting the degree of agreement between criteria levels or numerical experts’ judgments. The MPDI can be considered as another class of combining criteria that make effect of the degree of agreement among multiple numerical judgments. The MPDI is applicable in integrating several collaborative or synergistic decision making systems through combining final numerical decision outputs. A discussion and generalization of the proposed MPDI is discussed withnumerical example.

  18. Satisfying the Einstein-Podolsky-Rosen criterion with massive particles

    Science.gov (United States)

    Peise, J.; Kruse, I.; Lange, K.; Lücke, B.; Pezzè, L.; Arlt, J.; Ertmer, W.; Hammerer, K.; Santos, L.; Smerzi, A.; Klempt, C.

    2016-03-01

    In 1935, Einstein, Podolsky and Rosen (EPR) questioned the completeness of quantum mechanics by devising a quantum state of two massive particles with maximally correlated space and momentum coordinates. The EPR criterion qualifies such continuous-variable entangled states, as shown successfully with light fields. Here, we report on the production of massive particles which meet the EPR criterion for continuous phase/amplitude variables. The created quantum state of ultracold atoms shows an EPR parameter of 0.18(3), which is 2.4 standard deviations below the threshold of 1/4. Our state presents a resource for tests of quantum nonlocality with massive particles and a wide variety of applications in the field of continuous-variable quantum information and metrology.

  19. A Generalized Evolution Criterion in Nonequilibrium Convective Systems

    Science.gov (United States)

    Ichiyanagi, Masakazu; Nisizima, Kunisuke

    1989-04-01

    A general evolution criterion, applicable to transport processes such as the conduction of heat and mass diffusion, is obtained as a direct version of the Le Chatelier-Braun principle for stationary states. The present theory is not based on any radical departure from the conventional one. The generalized theory is made determinate by proposing the balance equations for extensive thermodynamic variables which will reflect the character of convective systems under the assumption of local equilibrium. As a consequence of the introduction of source terms in the balance equations, there appear additional terms in the expression of the local entropy production, which are bilinear in terms of the intensive variables and the sources. In the present paper, we show that we can construct a dissipation function for such general cases, in which the premises of the Glansdorff-Prigogine theory are accumulated. The new dissipation function permits us to formulate a generalized evolution criterion for convective systems.

  20. The Mercier Criterion in Reversed Shear Tokamak Plasmas

    International Nuclear Information System (INIS)

    Kessel, C.; Chance, M.S.; Jardin, S.C.

    1999-01-01

    A recent numerical study has found that, contrary to conventional theoretical and experimental expectations, reversed shear plasmas are unstable primarily because the term proportional to the shear in the Mercier criterion is destabilizing. In the present study, the role of the magnetic shear, both local and global, is examined for various tokamak configurations with monotonic and non-monotonic safety factor profiles. The enhancement of the local shear due to the outward shift of the magnetic axis suggests that the latter are less susceptible to interchanges. Furthermore, by regrouping the terms in the criterion, the V'' term when differentiated instead with respect to the toroidal flux, is shown to absorb the dominant shear term. No Mercier instability is found for similar profiles as in the previous study

  1. Establishment of an equivalence acceptance criterion for accelerated stability studies.

    Science.gov (United States)

    Burdick, Richard K; Sidor, Leslie

    2013-01-01

    In this article, the use of statistical equivalence testing for providing evidence of process comparability in an accelerated stability study is advocated over the use of a test of differences. The objective of such a study is to demonstrate comparability by showing that the stability profiles under nonrecommended storage conditions of two processes are equivalent. Because it is difficult at accelerated conditions to find a direct link to product specifications, and hence product safety and efficacy, an equivalence acceptance criterion is proposed that is based on the statistical concept of effect size. As with all statistical tests of equivalence, it is important to collect input from appropriate subject-matter experts when defining the acceptance criterion.

  2. On Feller's criterion for the law of the iterated logarithm

    Directory of Open Access Journals (Sweden)

    Deli Li

    1994-01-01

    Full Text Available Combining Feller's criterion with a non-uniform estimate result in the context of the Central Limit Theorem for partial sums of independent random variables, we obtain several results on the Law of the Iterated Logarithm. Two of these results refine corresponding results of Wittmann (1985 and Egorov (1971. In addition, these results are compared with the corresponding results of Teicher (1974, Tomkins (1983 and Tomkins (1990

  3. Statistical criterion for Bubbly-slug flow transition

    Energy Technology Data Exchange (ETDEWEB)

    Zigler, J; Elias, E [Technion-Israel Inst. of Tech., Haifa (Israel). Dept. of Mechanical Engineering

    1996-12-01

    The investigation of flow pattern transitions is still an interesting problem in the research of multiphase Row. It has been studied theoretically, and experimental confirmation of the models has been found by many investigators. The present paper deals with a statistical approach to bubbly-slug transitions in a vertical upward two phase flow and a new transition criterion is deduced from experimental data (authors).

  4. Ductile failure analysis of API X65 pipes with notch-type defects using a local fracture criterion

    International Nuclear Information System (INIS)

    Oh, Chang-Kyun; Kim, Yun-Jae; Baek, Jong-Hyun; Kim, Young-Pyo; Kim, Woo-Sik

    2007-01-01

    A local failure criterion for API X65 steel is applied to predict ductile failure of full-scale API X65 pipes with simulated corrosion and gouge defects under internal pressure. The local failure criterion is the stress-modified fracture strain as a function of the stress triaxiality (defined by the ratio of the hydrostatic stress to the effective stress). Based on detailed finite element (FE) analyses with the proposed local failure criterion, burst pressures of defective pipes are estimated and compared with experimental data. For pipes with simulated corrosion defects, FE analysis with the proposed local fracture criterion indicates that predicted failure takes place after the defective pipes attain maximum loads for all cases, possibly due to the fact that the material has sufficient ductility. For pipes with simulated gouge defects, on the other hand, it is found that predicted failure takes place before global instability, and the predicted burst pressures are in good agreement with experimental data, providing confidence in the present approach

  5. On the upper bound in the Bohm sheath criterion

    Energy Technology Data Exchange (ETDEWEB)

    Kotelnikov, I. A., E-mail: I.A.Kotelnikov@inp.nsk.su; Skovorodin, D. I., E-mail: D.I.Skovorodin@inp.nsk.su [Russian Academy of Sciences, Budker Institute of Nuclear Physics, Siberian Branch (Russian Federation)

    2016-02-15

    The question is discussed about the existence of an upper bound in the Bohm sheath criterion, according to which the Debye sheath at the interface between plasma and a negatively charged electrode is stable only if the ion flow velocity in plasma exceeds the ion sound velocity. It is stated that, with an exception of some artificial ionization models, the Bohm sheath criterion is satisfied as an equality at the lower bound and the ion flow velocity is equal to the speed of sound. In the one-dimensional theory, a supersonic flow appears in an unrealistic model of a localized ion source the size of which is less than the Debye length; however, supersonic flows seem to be possible in the two- and three-dimensional cases. In the available numerical codes used to simulate charged particle sources with a plasma emitter, the presence of the upper bound in the Bohm sheath criterion is not supposed; however, the correspondence with experimental data is usually achieved if the ion flow velocity in plasma is close to the ion sound velocity.

  6. Location Selection for Hardboard Industry in Mazandaran Province

    Directory of Open Access Journals (Sweden)

    Majid Azizi

    2012-01-01

    Full Text Available This research presents an optimum framework for hardboard industry location selection in Mazandaran Province. Considering the existence of only two depreciated hardboard plants with very old technology in Iran, the establishment of new plants are vital. To materialize this goal, Mazandaran province enjoys priorities to other provinces based on its resources of raw lignocellulosic materials required for wood and paper industries. The model presented in this article uses AHP benefit/cost ratios. The results indicate that the criterion of ‘material and production’ with a weight of 0.327 and the sub-criterion of ‘reliability of supply’ with a weight of 0.146 have the highest priorities, and the city of Sari is the best alternative.

  7. An Introduction to Model Selection: Tools and Algorithms

    Directory of Open Access Journals (Sweden)

    Sébastien Hélie

    2006-03-01

    Full Text Available Model selection is a complicated matter in science, and psychology is no exception. In particular, the high variance in the object of study (i.e., humans prevents the use of Popper’s falsification principle (which is the norm in other sciences. Therefore, the desirability of quantitative psychological models must be assessed by measuring the capacity of the model to fit empirical data. In the present paper, an error measure (likelihood, as well as five methods to compare model fits (the likelihood ratio test, Akaike’s information criterion, the Bayesian information criterion, bootstrapping and cross-validation, are presented. The use of each method is illustrated by an example, and the advantages and weaknesses of each method are also discussed.

  8. Some properties of the computable cross-norm criterion for separability

    International Nuclear Information System (INIS)

    Rudolph, Oliver

    2003-01-01

    The computable cross-norm (CCN) criterion is a powerful analytical and computable separability criterion for bipartite quantum states, which is also known to systematically detect bound entanglement. In certain aspects this criterion complements the well-known Peres positive partial transpose (PPT) criterion. In the present paper we study important analytical properties of the CCN criterion. We show that in contrast to the PPT criterion it is not sufficient in dimension 2x2. In higher dimensions, theorems connecting the fidelity of a quantum state with the CCN criterion are proved. We also analyze the behavior of the CCN criterion under local operations and identify the operations that leave it invariant. It turns out that the CCN criterion is in general not invariant under local operations

  9. Automated criterion-based analysis for Cole parameters assessment from cerebral neonatal electrical bioimpedance spectroscopy measurements

    International Nuclear Information System (INIS)

    Seoane, F; Lindecrantz, Kaj; Ward, L C; Lingwood, B E

    2012-01-01

    Hypothermia has been proven as an effective rescue therapy for infants with moderate or severe neonatal hypoxic ischemic encephalopathy. Hypoxia-ischemia alters the electrical impedance characteristics of the brain in neonates; therefore, spectroscopic analysis of the cerebral bioimpedance of the neonate may be useful for the detection of candidate neonates eligible for hypothermia treatment. Currently, in addition to the lack of reference bioimpedance data obtained from healthy neonates, there is no standardized approach established for bioimpedance spectroscopy data analysis. In this work, cerebral bioimpedance measurements (12 h postpartum) in a cross-section of 84 term and near-term healthy neonates were performed at the bedside in the post-natal ward. To characterize the impedance spectra, Cole parameters (R 0 , R ∞ , f C and α) were extracted from the obtained measurements using an analysis process based on a best measurement and highest likelihood selection process. The results obtained in this study complement previously reported work and provide a standardized criterion-based method for data analysis. The availability of electrical bioimpedance spectroscopy reference data and the automatic criterion-based analysis method might support the development of a non-invasive method for prompt selection of neonates eligible for cerebral hypothermic rescue therapy. (paper)

  10. Criterion-Referenced Values of Grip Strength and Usual Gait Speed Using Instrumental Activities of Daily Living Disability as the Criterion.

    Science.gov (United States)

    Lee, Meng-Chih; Hsu, Chih-Cheng; Tsai, Yi-Fen; Chen, Ching-Yu; Lin, Cheng-Chieh; Wang, Ching-Yi

    Current evidence suggests that grip strength and usual gait speed (UGS) are important predictors of instrumental activities of daily living (IADL) disability. Knowing the optimum cut points of these tests for discriminating people with and without IADL disability could help clinicians or researchers to better interpret the test results and make medical decisions. The purpose of this study was to determine the cutoff values of grip strength and UGS for best discriminating community-dwelling older adults with and without IADL disability, separately for men and women, and to investigate their association with IADL disability. We conducted secondary data analysis on a national dataset collected in the Sarcopenia and Translational Aging Research in Taiwan (START). The data used in this study consisted of health data of 2420 community-dwelling older adults 65 years and older with no history of stroke and with complete data. IADL disability was defined as at least 1 IADL item scored as "need help" or "unable to perform." Receiver operating characteristics analysis was used to estimate the optimum grip strength and UGS cut points for best discriminating older adults with/without IADL disability. The association between each physical performance (grip strength and UGS) and IADL disability was assessed with odds ratios (ORs). With IADL disability as the criterion, the optimal cutoff values of grip strength were 28.7 kg for men and 16.0 kg for women, and those for UGS were 0.76 m/s for men and 0.66 m/s for women. The grip strength test showed satisfactory discriminant validity (area under the curve > 0.7) in men and a strong association with IADL disability (OR > 4). Our cut points using IADL disability as the criterion were close to those indicating frailty or sarcopenia. Our reported cutoffs can serve as criterion-referenced values, along with those previously determined using different indicators, and provide important landmarks on the performance continua of older adults

  11. Numerical analysis oriented biaxial stress-strain relation and failure criterion of plain concrete

    International Nuclear Information System (INIS)

    Link, J.

    1975-01-01

    A biaxial stress-strain relation and failure criterion is proposed, which is applicable to structural analysis methods. The formulation of material behavior of plain concrete in biaxial stress-state was developed. A nonlinear elastic, anisotropic stress-strain relation was derived with two moduli of elasticity, E 1 , E 2 and Poisson's ratios, ν 1 , ν 2 , which depend on the prevailing biaxial stress state. The stress-strain relation is valid in the whole biaxial stress field, that means with a smooth transition between the domains of tension/tension, tension/compression and compression/compression. The stress-dependent moduli E 1 , E 2 and the Poisson's ratios ν 1 , ν 2 are approximated by polynomials, trigonometrical and exponential functions. A failure criterion was defined by approximating the test results of the biaxial ultimate concrete strength with a 7th degree polynomial, which is also valid in the whole biaxial stress domain. The definition of the state of failure is given as a function of stresses as well as strains. Initial parameters of the formulation of the biaxial material behavior are the uniaxial cylindrical strength of concrete and the initial values of Young's modulus and Poisson's ratio. A simple expansion of this formulation makes it applicable not only to normal but also to light-weight concrete. Comparison of numerically calculated stress-strain curves up to the ultimate biaxial stresses which indicate the failure criteria with those obtained from tests show a very good agreement. It is shown, that the biaxial stress-strain relation can be extended for use in cases of triaxial tension/tension/compression stress state. Numerical examples of analysis of concrete slabs show the importance of incorporation of a realistic material behavior for better safety estimations

  12. A uniqueness criterion for the Fock quantization of scalar fields with time-dependent mass

    International Nuclear Information System (INIS)

    Cortez, Jeronimo; Mena Marugan, Guillermo A; Olmedo, Javier; Velhinho, Jose M

    2011-01-01

    A major problem in the quantization of fields in curved spacetimes is the ambiguity in the choice of a Fock representation for the canonical commutation relations. There exists infinite number of choices leading to different physical predictions. In stationary scenarios, a common strategy is to select a vacuum (or a family of unitarily equivalent vacua) by requiring invariance under the spacetime symmetries. When stationarity is lost, a natural generalization consists in replacing time invariance by unitarity in the evolution. We prove that when the spatial sections are compact, the criterion of a unitary dynamics, together with the invariance under the spatial isometries, suffices to select a unique family of Fock quantizations for a scalar field with time-dependent mass. (fast track communication)

  13. Applying a new criterion to predict glass forming alloys in the Zr–Ni–Cu ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Déo, L.P., E-mail: leonardopratavieira@gmail.com [Universidade de São Paulo, EESC, SMM - Av. Trabalhador São Carlense, 400 – São Carlos, SP 13566-590 (Brazil); Mendes, M.A.B., E-mail: marcio.andreato@gmail.com [Universidade Federal de São Carlos, DEMa - Rod. Washington Luiz, Km 235 – São Carlos, SP 13565-905 (Brazil); Costa, A.M.S., E-mail: alexmatos1980@gmail.com [Universidade de São Paulo, DEMAR, EEL – Polo Urbo-Industrial Gleba AI-6, s/n – Lorena, SP 12600-970 (Brazil); Campos Neto, N.D., E-mail: nelsonddcn@gmail.com [Universidade de São Paulo, EESC, SMM - Av. Trabalhador São Carlense, 400 – São Carlos, SP 13566-590 (Brazil); Oliveira, M.F. de, E-mail: falcao@sc.usp.br [Universidade de São Paulo, EESC, SMM - Av. Trabalhador São Carlense, 400 – São Carlos, SP 13566-590 (Brazil)

    2013-03-15

    Highlights: ► Calculation to predict and select the glass forming ability (GFA) of metallic alloys in Zr–Ni–Cu system. ► Good correlation between theoretical and experimental GFA samples. ► Combination of X-ray diffraction (XRD) and differential scanning calorimetry (DSC) techniques mainly to characterize the samples. ► Oxygen impurity dramatically reduced the GFA. ► The selection criterion used opens the possibility to obtain new amorphous alloys, reducing the experimental procedures of trial and error. -- Abstract: A new criterion has been recently proposed to predict and select the glass forming ability (GFA) of metallic alloys. It was found that the critical cooling rate for glass formation (R{sub c}) correlates well with a proper combination of two factors, the minimum topological instability (λ{sub min}) and the thermodynamic parameter (Δh). The (λ{sub min}) criterion is based on the concept of topological instability of stable crystalline structures and (Δh) depends on the average work function difference (Δϕ) and the average electron density difference Δn{sub ws}{sup 1/3} among the constituent elements of the alloy. In the present work, the selection criterion was applied in the Zr–Ni–Cu system and its predictability was analyzed experimentally. Ribbon-shaped and splat-shaped samples were produced by melt-spinning and splat-cooling techniques respectively. The crystallization content and behavior were analyzed by X-ray diffraction (XRD) and differential scanning calorimetry (DSC), respectively. The results showed a good correlation between the theoretical GFA values and the amorphous phase percentages found in different alloy compositions.

  14. Carbon emissions and an equitable emission reduction criterion

    International Nuclear Information System (INIS)

    Golomb, Dan

    1999-01-01

    In 1995 the world-wide carbon emissions reached 5.8 billion metric tonnes per year (GTC/y). The Kyoto protocol calls for a reduction of carbon emissions from the developed countries (Annex I countries) of 6-8% below 1990 levels on the average, and unspecified commitments for the less developed (non-Annex I) countries. It is doubtful that the Kyoto agreement will be ratified by some parliaments, especially the USA Congress. Furthermore, it is shown that if the non-Annex I countries will not curtail their carbon emissions drastically, the global emissions will soar to huge levels by the middle of the next century. An equitable emission criterion is proposed which may lead to a sustainable rate of growth of carbon emissions, and be acceptable to all countries of the world. The criterion links the rate of growth of carbon emissions to the rate of growth of the Gross Domestic Product (GDP). A target criterion is proposed R = 0.15 KgC/SGDP, which is the current average for western European countries and Japan. This allows for both the growth of the GDP and carbon emissions. However, to reach the target in a reasonable time, the countries for which R≤ 0.3 would be allowed a carbon emission growth rate of 1%./y, and countries for which R≥ 0.3, 0.75%/y. It is shown that by 2050 the world-wide carbon emissions would reach about 10 GTC/y, which is about 3 times less than the Kyoto agreement would allow. (Author)

  15. Development of Predictor and Criterion Measures for the NCO21 Research Program

    National Research Council Canada - National Science Library

    Knapp, Deidre

    2002-01-01

    ... incorporated into an NCO performance management system geared to 21st century job demands. This report documents the design and development of predictor and criterion measures that will be used in a criterion-related validation data collection...

  16. Adjustment Criterion and Algorithm in Adjustment Model with Uncertain

    Directory of Open Access Journals (Sweden)

    SONG Yingchun

    2015-02-01

    Full Text Available Uncertainty often exists in the process of obtaining measurement data, which affects the reliability of parameter estimation. This paper establishes a new adjustment model in which uncertainty is incorporated into the function model as a parameter. A new adjustment criterion and its iterative algorithm are given based on uncertainty propagation law in the residual error, in which the maximum possible uncertainty is minimized. This paper also analyzes, with examples, the different adjustment criteria and features of optimal solutions about the least-squares adjustment, the uncertainty adjustment and total least-squares adjustment. Existing error theory is extended with new observational data processing method about uncertainty.

  17. Geometric steering criterion for two-qubit states

    Science.gov (United States)

    Yu, Bai-Chu; Jia, Zhih-Ahn; Wu, Yu-Chun; Guo, Guang-Can

    2018-01-01

    According to the geometric characterization of measurement assemblages and local hidden state (LHS) models, we propose a steering criterion which is both necessary and sufficient for two-qubit states under arbitrary measurement sets. A quantity is introduced to describe the required local resources to reconstruct a measurement assemblage for two-qubit states. We show that the quantity can be regarded as a quantification of steerability and be used to find out optimal LHS models. Finally we propose a method to generate unsteerable states, and construct some two-qubit states which are entangled but unsteerable under all projective measurements.

  18. Corner-point criterion for assessing nonlinear image processing imagers

    Science.gov (United States)

    Landeau, Stéphane; Pigois, Laurent; Foing, Jean-Paul; Deshors, Gilles; Swiathy, Greggory

    2017-10-01

    Range performance modeling of optronics imagers attempts to characterize the ability to resolve details in the image. Today, digital image processing is systematically used in conjunction with the optoelectronic system to correct its defects or to exploit tiny detection signals to increase performance. In order to characterize these processing having adaptive and non-linear properties, it becomes necessary to stimulate the imagers with test patterns whose properties are similar to the actual scene image ones, in terms of dynamic range, contours, texture and singular points. This paper presents an approach based on a Corner-Point (CP) resolution criterion, derived from the Probability of Correct Resolution (PCR) of binary fractal patterns. The fundamental principle lies in the respectful perception of the CP direction of one pixel minority value among the majority value of a 2×2 pixels block. The evaluation procedure considers the actual image as its multi-resolution CP transformation, taking the role of Ground Truth (GT). After a spatial registration between the degraded image and the original one, the degradation is statistically measured by comparing the GT with the degraded image CP transformation, in terms of localized PCR at the region of interest. The paper defines this CP criterion and presents the developed evaluation techniques, such as the measurement of the number of CP resolved on the target, the transformation CP and its inverse transform that make it possible to reconstruct an image of the perceived CPs. Then, this criterion is compared with the standard Johnson criterion, in the case of a linear blur and noise degradation. The evaluation of an imaging system integrating an image display and a visual perception is considered, by proposing an analysis scheme combining two methods: a CP measurement for the highly non-linear part (imaging) with real signature test target and conventional methods for the more linear part (displaying). The application to

  19. The alternative DSM-5 personality disorder traits criterion

    DEFF Research Database (Denmark)

    Bach, Bo; Maples-Keller, Jessica L; Bo, Sune

    2016-01-01

    The fifth edition of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5; American Psychiatric Association, 2013a) offers an alternative model for Personality Disorders (PDs) in Section III, which consists in part of a pathological personality traits criterion measured...... with the Personality Inventory for DSM-5 (PID-5). The PID-5 selfreport instrument currently exists in the original 220-item form, a short 100-item form, and a brief 25-item form. For clinicians and researchers, the choice of a particular PID- 5 form depends on feasibility, but also reliability and validity. The goal...

  20. An opening criterion for dust gaps in protoplanetary discs

    OpenAIRE

    Dipierro, Giovanni; Laibe, Guillaume

    2017-01-01

    We aim to understand under which conditions a low mass planet can open a gap in viscous dusty protoplanetary discs. For this purpose, we extend the theory of dust radial drift to include the contribution from the tides of an embedded planet and from the gas viscous forces. From this formalism, we derive i) a grain size-dependent criterion for dust gap opening in discs, ii) an estimate of the location of the outer edge of the dust gap and iii) an estimate of the minimum Stokes number above whi...

  1. Forecastability as a Design Criterion in Wind Resource Assessment: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, J.; Hodge, B. M.

    2014-04-01

    This paper proposes a methodology to include the wind power forecasting ability, or 'forecastability,' of a site as a design criterion in wind resource assessment and wind power plant design stages. The Unrestricted Wind Farm Layout Optimization (UWFLO) methodology is adopted to maximize the capacity factor of a wind power plant. The 1-hour-ahead persistence wind power forecasting method is used to characterize the forecastability of a potential wind power plant, thereby partially quantifying the integration cost. A trade-off between the maximum capacity factor and the forecastability is investigated.

  2. Critical machine cluster identification using the equal area criterion

    DEFF Research Database (Denmark)

    Weckesser, Johannes Tilman Gabriel; Jóhannsson, Hjörtur; Østergaard, Jacob

    2015-01-01

    The paper introduces a new method to early identify the critical machine cluster (CMC) after a transient disturbance. For transient stability assessment with methods based on the equal area criterion it is necessary to split the generators into a group of critical and non-critical machines....... The generators in the CMC are those likely to lose synchronism. The early and reliable identification of the CMC is crucial and one of the major challenges. The proposed new approach is based on the assessment of the rotor dynamics between two machines and the evaluation of their coupling strength. A novel...

  3. Ductile failure analysis of defective API X65 pipes based on stress-modified fracture strain criterion

    International Nuclear Information System (INIS)

    Oh, Chang Kyun; Kim, Yun Jae; Baek, Jong Hyun; Kim, Young Pyo; Kim, Woo Sik

    2006-01-01

    A local failure criterion for the API X65 steel is applied to predict ductile failure of full-scale API X65 pipes with simulated corrosion and gouge defects under internal pressure. The local failure criterion is the stress-modified fracture strain for the API X65 steel as a function of the stress triaxiality (defined by the ratio of the hydrostatic stress to the effective stress). Based on detailed FE analyses with the proposed local failure criteria, burst pressures of defective pipes are estimated and compared with experimental data. The predicted burst pressures are in good agreement with experimental data. Noting that an assessment equation against the gouge defect is not yet available, parametric study is performed, from which a simple equation is proposed to predict burst pressure for API X65 pipes with gouge defects

  4. Failure criterion for graphene in biaxial loading—a molecular dynamics study

    International Nuclear Information System (INIS)

    Yazdani, Hessam; Hatami, Kianoosh

    2015-01-01

    Molecular dynamics simulations are carried out in order to develop a failure criterion for infinite/bulk graphene in biaxial tension. Stresses along the principal edge configurations of graphene (i.e. armchair and zigzag directions) are normalized to the corresponding uniaxial ultimate strength values. The combinations of normalized stresses resulting in the failure of graphene are used to define failure envelopes (limiting stress ratio surfaces). Results indicate that a bilinear failure envelope can be used to represent the tensile strength of graphene in biaxial loading at different temperatures with reasonable accuracy. A circular failure envelope is also introduced for practical applications. Both failure envelopes define temperature-independent upper limits for the feasible combinations of normalized stresses for a graphene sheet in biaxial loading. Predicted failure modes of graphene under biaxial loading are also shown and discussed. (paper)

  5. [On the problems of the evolutionary optimization of life history. II. To justification of optimization criterion for nonlinear Leslie model].

    Science.gov (United States)

    Pasekov, V P

    2013-03-01

    The paper considers the problems in the adaptive evolution of life-history traits for individuals in the nonlinear Leslie model of age-structured population. The possibility to predict adaptation results as the values of organism's traits (properties) that provide for the maximum of a certain function of traits (optimization criterion) is studied. An ideal criterion of this type is Darwinian fitness as a characteristic of success of an individual's life history. Criticism of the optimization approach is associated with the fact that it does not take into account the changes in the environmental conditions (in a broad sense) caused by evolution, thereby leading to losses in the adequacy of the criterion. In addition, the justification for this criterion under stationary conditions is not usually rigorous. It has been suggested to overcome these objections in terms of the adaptive dynamics theory using the concept of invasive fitness. The reasons are given that favor the application of the average number of offspring for an individual, R(L), as an optimization criterion in the nonlinear Leslie model. According to the theory of quantitative genetics, the selection for fertility (that is, for a set of correlated quantitative traits determined by both multiple loci and the environment) leads to an increase in R(L). In terms of adaptive dynamics, the maximum R(L) corresponds to the evolutionary stability and, in certain cases, convergent stability of the values for traits. The search for evolutionarily stable values on the background of limited resources for reproduction is a problem of linear programming.

  6. Tabela de vida de fertilidade de três espécies neotropicais de Trichogrammatidae em ovos de hospedeiros alternativos como critério de seleção hospedeira Fertility life table of three neotropical species of Trichogrammatidae on factitious hosts as a criterion for selection of hosts

    Directory of Open Access Journals (Sweden)

    Nivia da Silva Dias

    2010-03-01

    Full Text Available Tabela de vida de fertilidade de três espécies neotropicais de Trichogrammatidae em ovos de hospedeiros alternativos como critério de seleção hospedeira. O objetivo deste trabalho foi selecionar o hospedeiro alternativo que permita o melhor desenvolvimento das três espécies neotropicais de tricogramatídeos, Trichogramma atopovirilia Oatman & Platner, 1983; Trichogramma bruni Nagaraja, 1983 e Trichogrammatoidea annulata De Santis, 1972, utilizando-se como parâmetro comparativo as tabelas de vida de fertilidade nos respectivos hospedeiros. Foram estimados a duração média de uma geração (T, taxa líquida de reprodução (Ro, razão infinitesimal (r m e a razão finita de aumento (λ. A tabela de vida de fertilidade pode ser utilizada para selecionar o hospedeiro alternativo mais adequado para as espécies de tricogramatídeos. Corcyra cephalonica (Stainton, 1865 (Lepidoptera, Pyralidae foi o hospedeiro alternativo mais adequado para criação de T. annulata e de T. bruni, enquanto que para T. atopovirilia, Anagasta kuehniella (Zeller, 1879 (Lepidoptera, Pyralidae e/ou C. cephalonica foram os hospedeiros mais adequados. Sitotroga cerealella (Olivier, 1819 (Lepidoptera, Gelechiidae apresentou baixa capacidade de aumento populacional para as três espécies de parasitóides, sendo, portanto, uma espécie inadequada como hospedeiro alternativo para as mesmas.The objective of this work was to select the factitious host that permit the best development of three neotropical Trichogrammatidae species, Trichogramma atopovirilia Oatman & Platner, 1983; Trichogramma bruni Nagaraja, 1983, and Trichogrammatoidea annulata De Santis, 1972, using the fertility life table on their respective hosts as a comparative parameter. Mean generation time (T, net reproductive rate (Ro, intrinsic rate of natural increase (r m and the finite rate of increase (λ were estimated. A fertility life table is useful to select the most adequate factitious hosts for the

  7. DESTRUCTION CRITERION IN MODEL OF NON-LINEAR ELASTIC PLASTIC MEDIUM

    Directory of Open Access Journals (Sweden)

    O. L. Shved

    2014-01-01

    Full Text Available The paper considers a destruction criterion in a specific phenomenological model of elastic plastic medium which significantly differs from the known criteria. In case of vector interpretation of rank-2 symmetric tensors yield surface in the Cauchy stress space is formed by closed piecewise concave surfaces of its deviator sections with due account of experimental data. Section surface is determined by normal vector which is selected from two private vectors of criterial “deviator” operator. Such selection is not always possible in the case of anisotropy growth. It is expected that destruction can only start when a process point in the stress space is located in the current deviator section of the yield surface. It occurs when a critical point appears in the section, and a private value of an operator becomes N-fold in the point that determines the private vector corresponding to the normal vector. Unique and reasonable selection of the normal vector becomes impossible in the critical point and an yield criteria loses its significance in the point.When the destruction initiation is determined there is a possibility of a special case due to the proposed conic form of the yield surface. The deviator section degenerates into the point at the yield surface peak. Criterion formulation at the surface peak lies in the fact that there is no physically correct solution while using a state equation in regard to elastic distortion measures with a fixed tensor of elastic turn. Such usage of the equation is always possible for the rest points of the yield surface and it is considered as an obligatory condition for determination of the deviator section. A critical point is generally absent at any deviator section of the yield surface for isotropic material. A limiting value of the mean stress has been calculated at uniform tension.

  8. Novel criterion for formation of metastable phase from undercooled melt

    International Nuclear Information System (INIS)

    Kuribayashi, Kazuhiko; Nagashio, Kosuke; Niwata, Kenji; Kumar, M.S. Vijaya; Hibiya, Taketoshi

    2007-01-01

    Undercooling a melt facilitates the preferential nucleation of a metastable phase. In the present study, the formation of metastable phases from undercooled melts was considered from the viewpoint of the competitive nucleation criterion. The classical nucleation theory shows us that the most critical factor for forming a critical nucleus is the interface free energy σ. Furthermore, Spaepen's negentropic model on σ generated the role of the scaling factor α that depends on the polyhedral order in the liquid and solid phases prominent in simple liquids such as the melt of monoatomic metals. In ionic materials such as oxides, however, in which oxygen polyhedrons including a cation at their center are the structural units both in the solid and liquid phases, the entropy of fusion, rather than α, can be expected to become dominant in the determination of σ. In accordance with this idea, using REFeO 3 as the model material (where RE denotes rare-earth elements) the entropy-undercooling regime criterion was proposed and verified

  9. Satisfying the Einstein–Podolsky–Rosen criterion with massive particles

    Science.gov (United States)

    Peise, J.; Kruse, I.; Lange, K.; Lücke, B.; Pezzè, L.; Arlt, J.; Ertmer, W.; Hammerer, K.; Santos, L.; Smerzi, A.; Klempt, C.

    2015-01-01

    In 1935, Einstein, Podolsky and Rosen (EPR) questioned the completeness of quantum mechanics by devising a quantum state of two massive particles with maximally correlated space and momentum coordinates. The EPR criterion qualifies such continuous-variable entangled states, where a measurement of one subsystem seemingly allows for a prediction of the second subsystem beyond the Heisenberg uncertainty relation. Up to now, continuous-variable EPR correlations have only been created with photons, while the demonstration of such strongly correlated states with massive particles is still outstanding. Here we report on the creation of an EPR-correlated two-mode squeezed state in an ultracold atomic ensemble. The state shows an EPR entanglement parameter of 0.18(3), which is 2.4 s.d. below the threshold 1/4 of the EPR criterion. We also present a full tomographic reconstruction of the underlying many-particle quantum state. The state presents a resource for tests of quantum nonlocality and a wide variety of applications in the field of continuous-variable quantum information and metrology. PMID:26612105

  10. Satisfying the Einstein-Podolsky-Rosen criterion with massive particles.

    Science.gov (United States)

    Peise, J; Kruse, I; Lange, K; Lücke, B; Pezzè, L; Arlt, J; Ertmer, W; Hammerer, K; Santos, L; Smerzi, A; Klempt, C

    2015-11-27

    In 1935, Einstein, Podolsky and Rosen (EPR) questioned the completeness of quantum mechanics by devising a quantum state of two massive particles with maximally correlated space and momentum coordinates. The EPR criterion qualifies such continuous-variable entangled states, where a measurement of one subsystem seemingly allows for a prediction of the second subsystem beyond the Heisenberg uncertainty relation. Up to now, continuous-variable EPR correlations have only been created with photons, while the demonstration of such strongly correlated states with massive particles is still outstanding. Here we report on the creation of an EPR-correlated two-mode squeezed state in an ultracold atomic ensemble. The state shows an EPR entanglement parameter of 0.18(3), which is 2.4 s.d. below the threshold 1/4 of the EPR criterion. We also present a full tomographic reconstruction of the underlying many-particle quantum state. The state presents a resource for tests of quantum nonlocality and a wide variety of applications in the field of continuous-variable quantum information and metrology.

  11. Physical and Constructive (Limiting) Criterions of Gear Wheels Wear

    Science.gov (United States)

    Fedorov, S. V.

    2018-01-01

    We suggest using a generalized model of friction - the model of elastic-plastic deformation of the body element, which is located on the surface of the friction pairs. This model is based on our new engineering approach to the problem of friction-triboergodynamics. Friction is examined as transformative and dissipative process. Structural-energetic interpretation of friction as a process of elasto-plastic deformation and fracture contact volumes is proposed. The model of Hertzian (heavy-loaded) friction contact evolution is considered. The least wear particle principle is formulated. It is mechanical (nano) quantum. Mechanical quantum represents the least structural form of solid material body in conditions of friction. It is dynamic oscillator of dissipative friction structure and it can be examined as the elementary nanostructure of metal’s solid body. At friction in state of most complete evolution of elementary tribosystem (tribocontact) all mechanical quanta (subtribosystems) with the exception of one, elasticity and reversibly transform energy of outer impact (mechanic movement). In these terms only one mechanical quantum is the lost - standard of wear. From this position we can consider the physical criterion of wear and the constructive (limiting) criterion of gear teeth and other practical examples of tribosystems efficiency with new tribology notion - mechanical (nano) quantum.

  12. Generalized melting criterion for beam-induced amorphization

    International Nuclear Information System (INIS)

    Lam, N. Q.; Okamoto, Paul R.

    1993-09-01

    Recent studies have shown that the mean-square static atomic displacements provide a generic measure of the enthalpy stored in the lattice in the form of chemical and topological disorder, and that the effect of the displacements on the softening of shear elastic constants is identical to that of heating. This finding lends support to a generalized form of the Lindemann phenomenological melting criterion and leads to a natural interpretion of crystalline-to-amorphous transformations as defect-induced melting of metastable crystals driven beyond a critical state of disorder where the melting temperature falls below the glass-transition temperature. Application of the generalized Lindemann criterion to both the crystalline and amorphous phases indicates that the enthalpies of the two phases become identical when their shear moduli become equal. This thermo-elastic rule provides a basis for predicting the relative susceptibility of compounds to amorphization in terms of their elastic properties as measured by Debye temperatures. The present approach can explain many of the basic findings on beam-induced amorphization of intermetallic compounds as well as amorphous phase formation associated with ion implantation, ion-beam mixing and other solid-state processes

  13. Some comments about the use of J1 integral criterion

    International Nuclear Information System (INIS)

    Roche, Roland.

    1977-01-01

    Use of J 1 integral criterion in Post Yield Fracture Mechanics is considered. If J 1 is path independent, it can be considered as a crack tip singularity characterization and then, as a good criterion for crack initiation. But it is not proved that J 1 is path independent in general case. The current practice is to consider a material with a mechanical potential energy, it is to say to suppose that strain energy W is only function of the state of strain, but not of the loading history. It is possible to introduce the defect vector concept (or driving force). The resultants of defect vectors included inside a volume are the surface integrals J vector and L vector. So the general condition for J 1 path indepedence can be written. It seems that J 1 is path independent for radial loading but the question is still open for more complex ways of loading. What is the effect of material memory on the J 1 path dependence [fr

  14. A dimensionless criterion for characterising internal transport barriers in tokamaks

    International Nuclear Information System (INIS)

    Tresset, G.; Litaudon, X.; Moreau, D.

    2000-07-01

    A simple criterion, based on a dimensionless parameter (ρ T * =ρ s /L T ) related to drift wave turbulence stabilisation and anomalous transport theory, is proposed in order to characterise the emergence and the space-time evolution of internal transport barriers (ITB's) during a tokamak discharge. The underlying physics which led us to consider the possible relevance of this parameter as a local indicator of a bifurcated plasma state is the breaking of the gyro-Bohm turbulence scaling by the diamagnetic velocity shear, which has been observed in various numerical simulations [e.g. X. Garbet and R.E. Waltz, Phys. Plasmas 3(1996) 1898]. The presence of an ITB is inferred when ρ T * exceeds a threshold value. The main features like the emergence time, location and even dynamics of ITB's can then be summarized on a single graphical representation consistent with measurement uncertainties. The validity of such a criterion is demonstrated on the Optimized Shear (OS) database of JET in several experimental configurations. Large database analysis and realtime control of OS discharges are envisaged as the most attractive applications. (author)

  15. The limits of the Bohm criterion in collisional plasmas

    International Nuclear Information System (INIS)

    Valentini, H.-B.; Kaiser, D.

    2015-01-01

    The sheath formation within a low-pressure collisional plasma is analysed by means of a two-fluid model. The Bohm criterion takes into account the effects of the electric field and the inertia of the ions. Numerical results yield that these effects contribute to the space charge formation, only, if the collisionality is lower than a relatively small threshold. It follows that a lower and an upper limit of the drift speed of the ions exist where the effects treated by Bohm can form a sheath. This interval becomes narrower as the collisionality increases and vanishes at the mentioned threshold. Above the threshold, the sheath is mainly created by collisions and the ionisation. Under these conditions, the sheath formation cannot be described by means of Bohm like criteria. In a few references, a so-called upper limit of the Bohm criterion is stated for collisional plasmas where the momentum equation of the ions is taken into account, only. However, the present paper shows that this limit results in an unrealistically steep increase of the space charge density towards the wall, and, therefore, it yields no useful limit of the Bohm velocity

  16. Cue quality and criterion setting in recognition memory.

    Science.gov (United States)

    Kent, Christopher; Lamberts, Koen; Patton, Richard

    2018-02-02

    Previous studies on how people set and modify decision criteria in old-new recognition tasks (in which they have to decide whether or not a stimulus was seen in a study phase) have almost exclusively focused on properties of the study items, such as presentation frequency or study list length. In contrast, in the three studies reported here, we manipulated the quality of the test cues in a scene-recognition task, either by degrading through Gaussian blurring (Experiment 1) or by limiting presentation duration (Experiment 2 and 3). In Experiments 1 and 2, degradation of the test cue led to worse old-new discrimination. Most importantly, however, participants were more liberal in their responses to degraded cues (i.e., more likely to call the cue "old"), demonstrating strong within-list, item-by-item, criterion shifts. This liberal response bias toward degraded stimuli came at the cost of increasing the false alarm rate while maintaining a constant hit rate. Experiment 3 replicated Experiment 2 with additional stimulus types (words and faces) but did not provide accuracy feedback to participants. The criterion shifts in Experiment 3 were smaller in magnitude than Experiments 1 and 2 and varied in consistency across stimulus type, suggesting, in line with previous studies, that feedback is important for participants to shift their criteria.

  17. Job shop scheduling problem with late work criterion

    Science.gov (United States)

    Piroozfard, Hamed; Wong, Kuan Yew

    2015-05-01

    Scheduling is considered as a key task in many industries, such as project based scheduling, crew scheduling, flight scheduling, machine scheduling, etc. In the machine scheduling area, the job shop scheduling problems are considered to be important and highly complex, in which they are characterized as NP-hard. The job shop scheduling problems with late work criterion and non-preemptive jobs are addressed in this paper. Late work criterion is a fairly new objective function. It is a qualitative measure and concerns with late parts of the jobs, unlike classical objective functions that are quantitative measures. In this work, simulated annealing was presented to solve the scheduling problem. In addition, operation based representation was used to encode the solution, and a neighbourhood search structure was employed to search for the new solutions. The case studies are Lawrence instances that were taken from the Operations Research Library. Computational results of this probabilistic meta-heuristic algorithm were compared with a conventional genetic algorithm, and a conclusion was made based on the algorithm and problem.

  18. Comparing hierarchical models via the marginalized deviance information criterion.

    Science.gov (United States)

    Quintero, Adrian; Lesaffre, Emmanuel

    2018-07-20

    Hierarchical models are extensively used in pharmacokinetics and longitudinal studies. When the estimation is performed from a Bayesian approach, model comparison is often based on the deviance information criterion (DIC). In hierarchical models with latent variables, there are several versions of this statistic: the conditional DIC (cDIC) that incorporates the latent variables in the focus of the analysis and the marginalized DIC (mDIC) that integrates them out. Regardless of the asymptotic and coherency difficulties of cDIC, this alternative is usually used in Markov chain Monte Carlo (MCMC) methods for hierarchical models because of practical convenience. The mDIC criterion is more appropriate in most cases but requires integration of the likelihood, which is computationally demanding and not implemented in Bayesian software. Therefore, we consider a method to compute mDIC by generating replicate samples of the latent variables that need to be integrated out. This alternative can be easily conducted from the MCMC output of Bayesian packages and is widely applicable to hierarchical models in general. Additionally, we propose some approximations in order to reduce the computational complexity for large-sample situations. The method is illustrated with simulated data sets and 2 medical studies, evidencing that cDIC may be misleading whilst mDIC appears pertinent. Copyright © 2018 John Wiley & Sons, Ltd.

  19. ACTION AS A CRITERION OF THE CAR OPERATING EFFECTIVENES

    Directory of Open Access Journals (Sweden)

    Stefan POSTRZEDNIK

    2016-06-01

    Full Text Available Currently used criteria for determining car operating efficiency in road traffic are, among others, emission of harmful substances, consumption of engine driving fuels, technical service and reliability of operation, safety of use. The operational characteristics of the car in terms of engine driving fuel consumption data is usually recognised as so-called road specific fuel consumption. An important deficiency of this approach is the failure to take into account the influence of the time on the journey’s effectiveness and the final result of the entire project. To obtain a new solution in this range in the analysis, a quantity called "action", which at last will be treated as the criterion of the car operating effectiveness, was used. The quantity of action is the product of the performed work and its realisation time. Many phenomena and processes in nature take place according to the principle of "minimum of action"  this criterion can be applied in the analysis of the car’s operating efficiency taking place in road traffic. An approach of this issue is presented in this article, wherein the basic data for analysis were obtained in the framework of the car tests performed at the real traffic conditions.

  20. PET image reconstruction: mean, variance, and optimal minimax criterion

    International Nuclear Information System (INIS)

    Liu, Huafeng; Guo, Min; Gao, Fei; Shi, Pengcheng; Xue, Liying; Nie, Jing

    2015-01-01

    Given the noise nature of positron emission tomography (PET) measurements, it is critical to know the image quality and reliability as well as expected radioactivity map (mean image) for both qualitative interpretation and quantitative analysis. While existing efforts have often been devoted to providing only the reconstructed mean image, we present a unified framework for joint estimation of the mean and corresponding variance of the radioactivity map based on an efficient optimal min–max criterion. The proposed framework formulates the PET image reconstruction problem to be a transformation from system uncertainties to estimation errors, where the minimax criterion is adopted to minimize the estimation errors with possibly maximized system uncertainties. The estimation errors, in the form of a covariance matrix, express the measurement uncertainties in a complete way. The framework is then optimized by ∞-norm optimization and solved with the corresponding H ∞ filter. Unlike conventional statistical reconstruction algorithms, that rely on the statistical modeling methods of the measurement data or noise, the proposed joint estimation stands from the point of view of signal energies and can handle from imperfect statistical assumptions to even no a priori statistical assumptions. The performance and accuracy of reconstructed mean and variance images are validated using Monte Carlo simulations. Experiments on phantom scans with a small animal PET scanner and real patient scans are also conducted for assessment of clinical potential. (paper)

  1. Refocusing criterion via sparsity measurements in digital holography.

    Science.gov (United States)

    Memmolo, Pasquale; Paturzo, Melania; Javidi, Bahram; Netti, Paolo A; Ferraro, Pietro

    2014-08-15

    Several automatic approaches have been proposed in the past to compute the refocus distance in digital holography (DH). However most of them are based on a maximization or minimization of a suitable amplitude image contrast measure, regarded as a function of the reconstruction distance parameter. Here we show that, by using the sparsity measure coefficient regarded as a refocusing criterion in the holographic reconstruction, it is possible to recover the focus plane and, at the same time, establish the degree of sparsity of digital holograms, when samples of the diffraction Fresnel propagation integral are used as a sparse signal representation. We employ a sparsity measurement coefficient known as Gini's index thus showing for the first time, to the best of our knowledge, its application in DH, as an effective refocusing criterion. Demonstration is provided for different holographic configurations (i.e., lens and lensless apparatus) and for completely different objects (i.e., a thin pure phase microscopic object as an in vitro cell, and macroscopic puppets) preparation.

  2. Tau hadronic branching ratios

    CERN Document Server

    Buskulic, Damir; De Bonis, I; Décamp, D; Ghez, P; Goy, C; Lees, J P; Lucotte, A; Minard, M N; Odier, P; Pietrzyk, B; Ariztizabal, F; Chmeissani, M; Crespo, J M; Efthymiopoulos, I; Fernández, E; Fernández-Bosman, M; Gaitan, V; Martínez, M; Orteu, S; Pacheco, A; Padilla, C; Palla, Fabrizio; Pascual, A; Perlas, J A; Sánchez, F; Teubert, F; Colaleo, A; Creanza, D; De Palma, M; Farilla, A; Gelao, G; Girone, M; Iaselli, Giuseppe; Maggi, G; Maggi, M; Marinelli, N; Natali, S; Nuzzo, S; Ranieri, A; Raso, G; Romano, F; Ruggieri, F; Selvaggi, G; Silvestris, L; Tempesta, P; Zito, G; Huang, X; Lin, J; Ouyang, Q; Wang, T; Xie, Y; Xu, R; Xue, S; Zhang, J; Zhang, L; Zhao, W; Bonvicini, G; Cattaneo, M; Comas, P; Coyle, P; Drevermann, H; Engelhardt, A; Forty, Roger W; Frank, M; Hagelberg, R; Harvey, J; Jacobsen, R; Janot, P; Jost, B; Kneringer, E; Knobloch, J; Lehraus, Ivan; Markou, C; Martin, E B; Mato, P; Minten, Adolf G; Miquel, R; Oest, T; Palazzi, P; Pater, J R; Pusztaszeri, J F; Ranjard, F; Rensing, P E; Rolandi, Luigi; Schlatter, W D; Schmelling, M; Schneider, O; Tejessy, W; Tomalin, I R; Venturi, A; Wachsmuth, H W; Wiedenmann, W; Wildish, T; Witzeling, W; Wotschack, J; Ajaltouni, Ziad J; Bardadin-Otwinowska, Maria; Barrès, A; Boyer, C; Falvard, A; Gay, P; Guicheney, C; Henrard, P; Jousset, J; Michel, B; Monteil, S; Pallin, D; Perret, P; Podlyski, F; Proriol, J; Rossignol, J M; Saadi, F; Fearnley, Tom; Hansen, J B; Hansen, J D; Hansen, J R; Hansen, P H; Nilsson, B S; Kyriakis, A; Simopoulou, Errietta; Siotis, I; Vayaki, Anna; Zachariadou, K; Blondel, A; Bonneaud, G R; Brient, J C; Bourdon, P; Passalacqua, L; Rougé, A; Rumpf, M; Tanaka, R; Valassi, Andrea; Verderi, M; Videau, H L; Candlin, D J; Parsons, M I; Focardi, E; Parrini, G; Corden, M; Delfino, M C; Georgiopoulos, C H; Jaffe, D E; Antonelli, A; Bencivenni, G; Bologna, G; Bossi, F; Campana, P; Capon, G; Chiarella, V; Felici, G; Laurelli, P; Mannocchi, G; Murtas, F; Murtas, G P; Pepé-Altarelli, M; Dorris, S J; Halley, A W; ten Have, I; Knowles, I G; Lynch, J G; Morton, W T; O'Shea, V; Raine, C; Reeves, P; Scarr, J M; Smith, K; Smith, M G; Thompson, A S; Thomson, F; Thorn, S; Turnbull, R M; Becker, U; Braun, O; Geweniger, C; Graefe, G; Hanke, P; Hepp, V; Kluge, E E; Putzer, A; Rensch, B; Schmidt, M; Sommer, J; Stenzel, H; Tittel, K; Werner, S; Wunsch, M; Beuselinck, R; Binnie, David M; Cameron, W; Colling, D J; Dornan, Peter J; Konstantinidis, N P; Moneta, L; Moutoussi, A; Nash, J; San Martin, G; Sedgbeer, J K; Stacey, A M; Dissertori, G; Girtler, P; Kuhn, D; Rudolph, G; Bowdery, C K; Brodbeck, T J; Colrain, P; Crawford, G; Finch, A J; Foster, F; Hughes, G; Sloan, Terence; Whelan, E P; Williams, M I; Galla, A; Greene, A M; Kleinknecht, K; Quast, G; Raab, J; Renk, B; Sander, H G; Wanke, R; Van Gemmeren, P; Zeitnitz, C; Aubert, Jean-Jacques; Bencheikh, A M; Benchouk, C; Bonissent, A; Bujosa, G; Calvet, D; Carr, J; Diaconu, C A; Etienne, F; Thulasidas, M; Nicod, D; Payre, P; Rousseau, D; Talby, M; Abt, I; Assmann, R W; Bauer, C; Blum, Walter; Brown, D; Dietl, H; Dydak, Friedrich; Ganis, G; Gotzhein, C; Jakobs, K; Kroha, H; Lütjens, G; Lutz, Gerhard; Männer, W; Moser, H G; Richter, R H; Rosado-Schlosser, A; Schael, S; Settles, Ronald; Seywerd, H C J; Saint-Denis, R; Wolf, G; Alemany, R; Boucrot, J; Callot, O; Cordier, A; Courault, F; Davier, M; Duflot, L; Grivaz, J F; Heusse, P; Jacquet, M; Kim, D W; Le Diberder, F R; Lefrançois, J; Lutz, A M; Musolino, G; Nikolic, I A; Park, H J; Park, I C; Schune, M H; Simion, S; Veillet, J J; Videau, I; Abbaneo, D; Azzurri, P; Bagliesi, G; Batignani, G; Bettarini, S; Bozzi, C; Calderini, G; Carpinelli, M; Ciocci, M A; Ciulli, V; Dell'Orso, R; Fantechi, R; Ferrante, I; Foà, L; Forti, F; Giassi, A; Giorgi, M A; Gregorio, A; Ligabue, F; Lusiani, A; Marrocchesi, P S; Messineo, A; Rizzo, G; Sanguinetti, G; Sciabà, A; Spagnolo, P; Steinberger, Jack; Tenchini, Roberto; Tonelli, G; Triggiani, G; Vannini, C; Verdini, P G; Walsh, J; Betteridge, A P; Blair, G A; Bryant, L M; Cerutti, F; Gao, Y; Green, M G; Johnson, D L; Medcalf, T; Mir, L M; Perrodo, P; Strong, J A; Bertin, V; Botterill, David R; Clifft, R W; Edgecock, T R; Haywood, S; Edwards, M; Maley, P; Norton, P R; Thompson, J C; Bloch-Devaux, B; Colas, P; Emery, S; Kozanecki, Witold; Lançon, E; Lemaire, M C; Locci, E; Marx, B; Pérez, P; Rander, J; Renardy, J F; Roussarie, A; Schuller, J P; Schwindling, J; Trabelsi, A; Vallage, B; Johnson, R P; Kim, H Y; Litke, A M; McNeil, M A; Taylor, G; Beddall, A; Booth, C N; Boswell, R; Cartwright, S L; Combley, F; Dawson, I; Köksal, A; Letho, M; Newton, W M; Rankin, C; Thompson, L F; Böhrer, A; Brandt, S; Cowan, G D; Feigl, E; Grupen, Claus; Lutters, G; Minguet-Rodríguez, J A; Rivera, F; Saraiva, P; Smolik, L; Stephan, F; Apollonio, M; Bosisio, L; Della Marina, R; Giannini, G; Gobbo, B; Ragusa, F; Rothberg, J E; Wasserbaech, S R; Armstrong, S R; Bellantoni, L; Elmer, P; Feng, Z; Ferguson, D P S; Gao, Y S; González, S; Grahl, J; Harton, J L; Hayes, O J; Hu, H; McNamara, P A; Nachtman, J M; Orejudos, W; Pan, Y B; Saadi, Y; Schmitt, M; Scott, I J; Sharma, V; Turk, J; Walsh, A M; Wu Sau Lan; Wu, X; Yamartino, J M; Zheng, M; Zobernig, G

    1996-01-01

    From 64492 selected \\tau-pair events, produced at the Z^0 resonance, the measurement of the tau decays into hadrons from a global analysis using 1991, 1992 and 1993 ALEPH data is presented. Special emphasis is given to the reconstruction of photons and \\pi^0's, and the removal of fake photons. A detailed study of the systematics entering the \\pi^0 reconstruction is also given. A complete and consistent set of tau hadronic branching ratios is presented for 18 exclusive modes. Most measurements are more precise than the present world average. The new level of precision reached allows a stringent test of \\tau-\\mu universality in hadronic decays, g_\\tau/g_\\mu \\ = \\ 1.0013 \\ \\pm \\ 0.0095, and the first measurement of the vector and axial-vector contributions to the non-strange hadronic \\tau decay width: R_{\\tau ,V} \\ = \\ 1.788 \\ \\pm \\ 0.025 and R_{\\tau ,A} \\ = \\ 1.694 \\ \\pm \\ 0.027. The ratio (R_{\\tau ,V} - R_{\\tau ,A}) / (R_{\\tau ,V} + R_{\\tau ,A}), equal to (2.7 \\pm 1.3) \\ \\%, is a measure of the importance of Q...

  3. A Path-Independent Forming Limit Criterion for Stamping Simulations

    International Nuclear Information System (INIS)

    Zhu Xinhai; Chappuis, Laurent; Xia, Z. Cedric

    2005-01-01

    Forming Limit Diagram (FLD) has been proved to be a powerful tool for assessing necking failures in sheet metal forming analysis for majority of stamping operations over the last three decades. However, experimental evidence and theoretical analysis suggest that its applications are limited to linear or almost linear strain paths during its deformation history. Abrupt changes or even gradual deviations from linear strain-paths will shift forming limit curves from their original values, a situation that occurs in vast majority of sequential stamping operations such as where the drawing process is followed by flanging and re-strike processes. Various forming limit models have been put forward recently to provide remedies for the problem, noticeably stress-based and strain gradient-based forming limit criteria. This study presents an alternative path-independent forming limit criterion. Instead of traditional Forming Limit Diagrams (FLD) which are constructed in terms of major - minor principal strains throughout deformation history, the new criterion defines a critical effective strain ε-bar* as the limit strain for necking, and it is shown that ε-bar* can be expressed as a function of current strain rate state and material work hardening properties, without the need of explicitly considering strain-path effects. It is given by ε-bar* = f(β, k, n) where β = (dε 2 /dε 1 ) at current deformation state, and k and n are material strain hardening parameters if a power law is assumed. The analysis is built upon previous work by Storen and Rice [1975] and Zhu et al [2002] with the incorporation of anisotropic yield models such as Hill'48 for quadratic orthotropic yield and Hill'79 for non-quadratic orthotropic yield. Effects of anisotropic parameters such as R-values and exponent n-values on necking are investigated in detail for a variety of strain paths. Results predicted according to current analysis are compared against experimental data gathered from literature

  4. Psychometric aspects of item mapping for criterion-referenced interpretation and bookmark standard setting.

    Science.gov (United States)

    Huynh, Huynh

    2010-01-01

    Locating an item on an achievement continuum (item mapping) is well-established in technical work for educational/psychological assessment. Applications of item mapping may be found in criterion-referenced (CR) testing (or scale anchoring, Beaton and Allen, 1992; Huynh, 1994, 1998a, 2000a, 2000b, 2006), computer-assisted testing, test form assembly, and in standard setting methods based on ordered test booklets. These methods include the bookmark standard setting originally used for the CTB/TerraNova tests (Lewis, Mitzel, Green, and Patz, 1999), the item descriptor process (Ferrara, Perie, and Johnson, 2002) and a similar process described by Wang (2003) for multiple-choice licensure and certification examinations. While item response theory (IRT) models such as the Rasch and two-parameter logistic (2PL) models traditionally place a binary item at its location, Huynh has argued in the cited papers that such mapping may not be appropriate in selecting items for CR interpretation and scale anchoring.

  5. Sequential lineups: shift in criterion or decision strategy?

    Science.gov (United States)

    Gronlund, Scott D

    2004-04-01

    R. C. L. Lindsay and G. L. Wells (1985) argued that a sequential lineup enhanced discriminability because it elicited use of an absolute decision strategy. E. B. Ebbesen and H. D. Flowe (2002) argued that a sequential lineup led witnesses to adopt a more conservative response criterion, thereby affecting bias, not discriminability. Height was encoded as absolute (e.g., 6 ft [1.83 m] tall) or relative (e.g., taller than). If a sequential lineup elicited an absolute decision strategy, the principle of transfer-appropriate processing predicted that performance should be best when height was encoded absolutely. Conversely, if a simultaneous lineup elicited a relative decision strategy, performance should be best when height was encoded relatively. The predicted interaction was observed, providing direct evidence for the decision strategies explanation of what happens when witnesses view a sequential lineup.

  6. A criterion and mechanism for power ramp defects

    International Nuclear Information System (INIS)

    Garlick, A.; Gravenor, J.G.

    1978-02-01

    The problem of power ramp defects in water reactor fuel pins is discussed in relation to results recently obtained from ramp experiments in the Steam Generating Heavy Water Reactor. Cladding cracks in the defected fuel pins were similar, both macro- and micro structurally, to those in unirradiated Zircaloy exposed to iodine stress-corrosion cracking (scc) conditions. Furthermore, when the measured stress levels for scc in short-term tests were taken as a criterion for ramp defects, UK fuel modelling codes were found to give a useful indication of defect probability under reactor service conditions. The likelihood of sticking between fuel and cladding is discussed and evidence presented which suggests that even at power a degree of adhesion may be expected in some fuel pins. The ramp defect mechanism is discussed in terms of fission product scc, initiation being by intergranular penetration and propagation by cleavage when suitably orientated grains are exposed to large dilatational stresses ahead of the main crack. (author)

  7. Error sensitivity to refinement: a criterion for optimal grid adaptation

    Science.gov (United States)

    Luchini, Paolo; Giannetti, Flavio; Citro, Vincenzo

    2017-12-01

    Most indicators used for automatic grid refinement are suboptimal, in the sense that they do not really minimize the global solution error. This paper concerns with a new indicator, related to the sensitivity map of global stability problems, suitable for an optimal grid refinement that minimizes the global solution error. The new criterion is derived from the properties of the adjoint operator and provides a map of the sensitivity of the global error (or its estimate) to a local mesh refinement. Examples are presented for both a scalar partial differential equation and for the system of Navier-Stokes equations. In the last case, we also present a grid-adaptation algorithm based on the new estimator and on the FreeFem++ software that improves the accuracy of the solution of almost two order of magnitude by redistributing the nodes of the initial computational mesh.

  8. QV modal distance displacement - a criterion for contingency ranking

    Energy Technology Data Exchange (ETDEWEB)

    Rios, M.A.; Sanchez, J.L.; Zapata, C.J. [Universidad de Los Andes (Colombia). Dept. of Electrical Engineering], Emails: mrios@uniandes.edu.co, josesan@uniandes.edu.co, cjzapata@utp.edu.co

    2009-07-01

    This paper proposes a new methodology using concepts of fast decoupled load flow, modal analysis and ranking of contingencies, where the impact of each contingency is measured hourly taking into account the influence of each contingency over the mathematical model of the system, i.e. the Jacobian Matrix. This method computes the displacement of the reduced Jacobian Matrix eigenvalues used in voltage stability analysis, as a criterion of contingency ranking, considering the fact that the lowest eigenvalue in the normal operation condition is not the same lowest eigenvalue in N-1 contingency condition. It is made using all branches in the system and specific branches according to the IBPF index. The test system used is the IEEE 118 nodes. (author)

  9. Goldberger-Treiman constraint criterion for hyperon coupling constants

    International Nuclear Information System (INIS)

    General, Ignacio J.; Cotanch, Stephen R.

    2004-01-01

    The generalized Goldberger-Treiman relation is combined with the Dashen-Weinstein sum rule to provide a constraint equation between the g KΣN and g KΛN coupling constants. A comprehensive examination of the published phenomenological and theoretical hyperon couplings has yielded a much smaller set of values, spanning the intervals 0.80≤g KΣN /√(4π)≤2.72 and -3.90≤g KΛN /√(4π)≤-1.84, consistent with this criterion. The broken SU F (3) and Goldberger-Treiman hyperon couplings satisfy the constraint along with predictions from a Taylor series extrapolation using the same momentum variation as exhibited by g πNN

  10. PRINCIPLE OF PROPORTIONALITY, CRITERION OF LEGITIMACY IN THE PUBLIC LAW

    Directory of Open Access Journals (Sweden)

    MARIUS ANDREESCU

    2011-04-01

    Full Text Available A problem of essence of the state is the one to delimit the discretionary power, respectively the power abuse in the activity of the state’s institutions. The legal behavior of the state’s institutions consists in their right to appreciate them and the power excess generates the violation of a subjective right or of the right that is of legitimate interest to the citizen. The application and nonobservance of the principle of lawfulness in the activities of the state is a complex problem because the exercise of the state’s functions assumes the discretionary powers with which the states authorities are invested, or otherwise said the ‘right of appreciation” of the authorities regarding the moment of adopting the contents of the measures proposed. The discretionary power cannot be opposed to the principle of lawfulness, as a dimension of the state de jure. In this study we propose to analyze the concept of discretionary power, respectively the power excess, having as a guidance the legislation, jurisprudence and doctrine in the matter. At the same time we would like to identify the most important criterions that will allow the user, regardless that he is or not an administrator, a public clerk or a judge, to delimit the legal behavior of the state’s institutions from the power excess. Within this context, we appreciate that the principle of proportionality represents such a criterion. The proportionality is a legal principle of the law, but at the same time it is a principle of the constitutional law and of other law branches. It expresses clearly the idea of balance, reasonability but also of adjusting the measures ordered by the state’s authorities to the situation in fact, respectively to the purpose for which they have been conceived. In our study we choose theoretical and jurisprudence arguments according to which the principle of proportionality can procedurally be determined and used to delimit the discretionary power and

  11. A study on the criterions of lean burn limit for an LPG EFI engine. Paper no. IGEC-1-140

    International Nuclear Information System (INIS)

    Li, L.; Wang, Z.; Xiao, Z.; Wang, H.; Deng, B.; Su, Y.

    2005-01-01

    Based on electronic low-pressure gaseous injection, the comparing analysis of several methods for the criterions of lean burn limit in an LPG engine is presented. Experiments are carried out in a single cylinder, four-stroke, water-cooled, 125cc engine with electronic LPG injection. According to the analysis of multi-parameters in and out cylinder, it shows that variation coefficient of indicated pressure which is the classical judgment of lean burn limit, the HC emission, HC emission rising gradient, the misfiring rate and the variation coefficient of the crank angle of the maximum combustion pressure can be as the criterions for lean burn limit. For the test engine, 15% as variation coefficient of indicative mean pressure, 500 x 10 -6 as HC emission, 2000 x 10 -6 as HC emission rising ratio, 1% as misfiring rate and 50% as variation coefficient of the crank angle of the maximum combustion pressure can be as the judgment criterions of LPG lean burn limits. (author)

  12. Applicability of the Modified Ritchie-Knott-Rice Failure Criterion to Examine the Feasibility of Miniaturized Charpy Type SE(B Specimens

    Directory of Open Access Journals (Sweden)

    Toshiyuki Meshii

    2016-01-01

    Full Text Available This paper examined whether the modified Ritchie-Knott-Rice (RKR failure criterion can be applied to examine the feasibility of miniaturized Charpy type SE(B specimens of thickness-to-width ratio B/W=1. The modified RKR failure criterion considered in this paper is the (4δt,σ22c criterion which predicts the onset of cleavage fracture when the midplane crack-opening stress measured at a distance equal to four times the crack-tip opening displacement, denoted as σ22d, exceeds a critical stress σ22c. Specimens with B values of 25, 10, 3, and 2 mm (denoted as 25t, 10t, 3t, and 2t specimens, resp. manufactured with 0.55% carbon steel were tested at 20°C. The results showed that the modified RKR criterion could appropriately predict the occurrence of cleavage fracture accompanied by negligibly small stable crack extension (denoted as KJc fracture naturally for the 25t and 10t specimens. The modified RKR criterion could also predict that KJc fracture does not occur for the 2t specimen. The σ22c obtained from specimens for the 25t and 10t specimens exhibited only a small difference, indicating that the Jc obtained from the 10t specimens can be used to predict the Jc that will be obtained with the 25t specimens.

  13. An Elasto-Plastic Damage Model for Rocks Based on a New Nonlinear Strength Criterion

    Science.gov (United States)

    Huang, Jingqi; Zhao, Mi; Du, Xiuli; Dai, Feng; Ma, Chao; Liu, Jingbo

    2018-05-01

    The strength and deformation characteristics of rocks are the most important mechanical properties for rock engineering constructions. A new nonlinear strength criterion is developed for rocks by combining the Hoek-Brown (HB) criterion and the nonlinear unified strength criterion (NUSC). The proposed criterion takes account of the intermediate principal stress effect against HB criterion, as well as being nonlinear in the meridian plane against NUSC. Only three parameters are required to be determined by experiments, including the two HB parameters σ c and m i . The failure surface of the proposed criterion is continuous, smooth and convex. The proposed criterion fits the true triaxial test data well and performs better than the other three existing criteria. Then, by introducing the Geological Strength Index, the proposed criterion is extended to rock masses and predicts the test data well. Finally, based on the proposed criterion, a triaxial elasto-plastic damage model for intact rock is developed. The plastic part is based on the effective stress, whose yield function is developed by the proposed criterion. For the damage part, the evolution function is assumed to have an exponential form. The performance of the constitutive model shows good agreement with the results of experimental tests.

  14. P2-17: Individual Differences in Dynamic Criterion Shifts during Perceptual Decision Making

    Directory of Open Access Journals (Sweden)

    Issac Rhim

    2012-10-01

    Full Text Available Perceptual decision-making involves placing an optimal criterion on the axis of encoded sensory evidence to maximize outcomes for choices. Optimal criterion setting becomes critical particularly when neural representations of sensory inputs are noisy and feedbacks for perceptual choices vary over time in an unpredictable manner. Here we monitored time courses of decision criteria that are adopted by human subjects while abruptly shifting the criterion of stochastic feedback to perceptual choices with certain amounts in an unpredictable direction and at an unpredictable point of time. Subjects viewed a brief (0.3 s, thin (.07 deg annulus around the fixation and were forced to judge whether the annulus was smaller or larger than an unknown boundary. We estimated moment-to-moment criteria by fitting a cumulative Gaussian function to the data within a sliding window of trials that are locked to a shift in feedback criterion. Unpredictable shifts in feedback criterion successfully induced shifts in actual decision criterion towards an optimal criterion for many of subjects, but with time delay and amount of shifts varying across individual subjects. There were disproportionately more numbers of overshooters (reaching and then surpassing the optimal criterion required than undershooters (subpar reach, with a significant anti-correlation with sensory sensitivity. To find a mechanism that generates these individual differences, we developed a dynamic criterion learning model by modifying a reinforcement learning model, which assumes that a criterion is adjusted every trial by a weighted discrepancy between actual and expected rewards.

  15. 76 FR 33740 - Final Priorities and Selection Criterion; National Institute on Disability and Rehabilitation...

    Science.gov (United States)

    2011-06-09

    ... leading collaborative research within the SCIMS program. While only SCIMS Centers can apply as lead... collaborative research project must contribute to this outcome by-- (a) Collaborating with three or more of the...

  16. Susceptibility of bifidobacteria to lysozyme as a possible selection criterion for probiotic bifidobacterial strains

    Czech Academy of Sciences Publication Activity Database

    Rada, V.; Šplíchal, Igor; Rocková, S.; Grmanová, M.; Vlková, E.

    2010-01-01

    Roč. 32, č. 3 (2010), s. 451-455 ISSN 0141-5492 R&D Projects: GA ČR GA523/07/0572 Institutional research plan: CEZ:AV0Z50200510 Keywords : Bifidobacteria * human milk * Lysozyme Subject RIV: EE - Microbiology, Virology Impact factor: 1.768, year: 2010

  17. Geoscience Education and Public Outreach AND CRITERION 2: MAKING A BROADER IMPACT

    Science.gov (United States)

    Marlino, M.; Scotchmoor, J. G.

    2005-12-01

    The geosciences influence our daily lives and yet often go unnoticed by the general public. From the moment we listen to the weather report and fill-up our cars for the daily commute, until we return to our homes constructed from natural resources, we rely on years of scientific research. The challenge facing the geosciences is to make explicit to the public not only the criticality of the research whose benefits they enjoy, but also to actively engage them as partners in the research effort, by providing them with sufficient understanding of the scientific enterprise so that they become thoughtful and proactive when making decisions in the polling booth. Today, there is broad recognition within the science and policy community that communication needs to be more effective, more visible, and that the public communication of the scientific enterprise is critical not only to its taxpayer support, but also to maintenance of a skilled workforce and the standard of living expected by many Americans. In 1997, the National Science Board took the first critical step in creating a cultural change in the scientific community by requiring explicit consideration of the broader impacts of research in every research proposal. The so-called Criterion 2 has catalyzed a dramatic shift in expectations within the geoscience community and an incentive for finding ways to encourage the science research community to select education and public outreach as a venue for responding to Criterion 2. In response, a workshop organized by the University of California Museum of Paleontology and the Digital Library for Earth System Education (DLESE) was held on the Berkeley campus May 11-13, 2005. The Geoscience EPO Workshop purposefully narrowed its focus to that of education and public outreach. This workshop was based on the premise that there are proven models and best practices for effective outreach strategies that need to be identified and shared with research scientists. Workshop

  18. Econometric models for predicting confusion crop ratios

    Science.gov (United States)

    Umberger, D. E.; Proctor, M. H.; Clark, J. E.; Eisgruber, L. M.; Braschler, C. B. (Principal Investigator)

    1979-01-01

    Results for both the United States and Canada show that econometric models can provide estimates of confusion crop ratios that are more accurate than historical ratios. Whether these models can support the LACIE 90/90 accuracy criterion is uncertain. In the United States, experimenting with additional model formulations could provide improved methods models in some CRD's, particularly in winter wheat. Improved models may also be possible for the Canadian CD's. The more aggressive province/state models outperformed individual CD/CRD models. This result was expected partly because acreage statistics are based on sampling procedures, and the sampling precision declines from the province/state to the CD/CRD level. Declining sampling precision and the need to substitute province/state data for the CD/CRD data introduced measurement error into the CD/CRD models.

  19. Validation of a Criterion for Cam Mechanisms Optimization Using Constraints upon Cam’s Curvature

    Directory of Open Access Journals (Sweden)

    Stelian Alaci

    2016-06-01

    Full Text Available For the mechanism with rotating cam and knife-edge follower, an optimization criterion by means of imposed constraints upon cam’s curvature is expressed in a special coordinate system. Thus, stating the optimization criterion in the coordinate system defined by the mechanisms constructive parameters -eccentricity and minimum follower’s stroke, a contour is obtained for any position of the mechanism. The optimization criterion assumes establishing the position of the characteristic point of the mechanism with respect to this contour. Fulfillment of optimization criterion assumes that the characteristic point is positioned in the same manner with respect to all contours. The optimization criterion is simplified when considering the envelope of the contours. The method is exemplified using two mechanisms, with the cams priori satisfying the criterion.

  20. Fluency: an aim in teaching and a criterion in assessment

    Directory of Open Access Journals (Sweden)

    Aud Marit Simensen

    2010-05-01

    Full Text Available This article investigates the concept ‘fluency’ from different perspectives. When fluency is an aim in teaching, a thorough comprehension of the concept among teachers is a prerequisite for appropriate planning of instruction, including the choice of appropriate classroom activities. When fluency is an assessment criterion, it is even more important that examiners have a shared perception of the concept. The present article starts by presenting common perceptions of the concept and goes on to explore some of the current research. Next, it provides a historical overview of the place of fluency in teaching theory and explains some of the preconditions for the inclusion of this concept among teaching objectives and assessment criteria. It will also, as an illustration, give an outline of the position of the concept over time in the Norwegian school system on the basis of an analysis of the relevant syllabuses. Finally, the article explicates the notion of language use as a complex cognitive skill and explores current method¬ological ideas about teaching towards fluency.

  1. The instability criterion for ideal and resistive MHD modes

    International Nuclear Information System (INIS)

    Li Ding

    2002-01-01

    The instability criterions for ideal helical perturbation and resistive kink/tearing modes are derived for arbitrary q profile. It is found that the q=1 mode can be unstable only within the q=1 surface in positive shear plasma. The instability region is enlarged as q 0 decreases and/or the current density is flatted. The instability can be completely suppressed in the reverse shear plasma for peaked, and flatted current profile. The q>1 modes are stable in the plasma core and marginal stable within the rational surface in the positive shear plasma. They become more stable in the plasma core and still marginal stable around the rational surface in the reversed shear plasma. It is shown that in the positive shear plasma, the q=1, 5/4, 4/3, 3/2 and 2/1 modes are in turn destabilized and becomes dominant unstable mode as q 0 increases for fixed q a . In the reversed shear plasma, all the q=1 and q>1 modes can be stable when q0 1 modes in turn becomes unstable as q 0 (>1) increases. At first, the inner branch is stable while the outer branch weakly unstable. Then, the both branches can become strongly unstable as q0 increases. (author)

  2. Robust Deep Network with Maximum Correntropy Criterion for Seizure Detection

    Directory of Open Access Journals (Sweden)

    Yu Qi

    2014-01-01

    Full Text Available Effective seizure detection from long-term EEG is highly important for seizure diagnosis. Existing methods usually design the feature and classifier individually, while little work has been done for the simultaneous optimization of the two parts. This work proposes a deep network to jointly learn a feature and a classifier so that they could help each other to make the whole system optimal. To deal with the challenge of the impulsive noises and outliers caused by EMG artifacts in EEG signals, we formulate a robust stacked autoencoder (R-SAE as a part of the network to learn an effective feature. In R-SAE, the maximum correntropy criterion (MCC is proposed to reduce the effect of noise/outliers. Unlike the mean square error (MSE, the output of the new kernel MCC increases more slowly than that of MSE when the input goes away from the center. Thus, the effect of those noises/outliers positioned far away from the center can be suppressed. The proposed method is evaluated on six patients of 33.6 hours of scalp EEG data. Our method achieves a sensitivity of 100% and a specificity of 99%, which is promising for clinical applications.

  3. A novel SURE-based criterion for parametric PSF estimation.

    Science.gov (United States)

    Xue, Feng; Blu, Thierry

    2015-02-01

    We propose an unbiased estimate of a filtered version of the mean squared error--the blur-SURE (Stein's unbiased risk estimate)--as a novel criterion for estimating an unknown point spread function (PSF) from the degraded image only. The PSF is obtained by minimizing this new objective functional over a family of Wiener processings. Based on this estimated blur kernel, we then perform nonblind deconvolution using our recently developed algorithm. The SURE-based framework is exemplified with a number of parametric PSF, involving a scaling factor that controls the blur size. A typical example of such parametrization is the Gaussian kernel. The experimental results demonstrate that minimizing the blur-SURE yields highly accurate estimates of the PSF parameters, which also result in a restoration quality that is very similar to the one obtained with the exact PSF, when plugged into our recent multi-Wiener SURE-LET deconvolution algorithm. The highly competitive results obtained outline the great potential of developing more powerful blind deconvolution algorithms based on SURE-like estimates.

  4. WPS criterion proposition based on experimental data base interpretation

    International Nuclear Information System (INIS)

    Chapuliot, S.; Izard, J.P.; Moinereau, D.; Marie, S.

    2011-01-01

    This article gives the background and the methodology developed to define a K J based criterion for brittle fracture of Reactor Pressure Vessel (RPV) submitted to Pressurized Thermal Shock (PTS), and taking into account Warm Pre Stressing effect (WPS). The first step of this methodology is the constitution of an experimental data base. This work was performed through bibliography and partnerships, and allows merging experimental results dealing with: -) Various ferritic steels; -) Various material states (as received, thermally aged, irradiated...); -) Various mode of fracture (cleavage, inter-granular, mixed mode); -) Various specimen geometry and size (CT, SENB, mock-ups); -) Various thermo-mechanical transients. Based on this experimental data base, a simple K J based limit is proposed and compared to experimental results. Parametric studies are performed in order to define the main parameters of the problem. Finally, a simple proposition based on a detailed analysis of tests results is performed. This proposition giving satisfactory results in every cases, it constitutes a good candidate for integration in French RSE-M code for in service assessment. (authors)

  5. A New Criterion for Prediction of Hot Tearing Susceptibility of Cast Alloys

    Science.gov (United States)

    Nasresfahani, Mohamad Reza; Niroumand, Behzad

    2014-08-01

    A new criterion for prediction of hot tearing susceptibility of cast alloys is suggested which takes into account the effects of both important mechanical and metallurgical factors and is believed to be less sensitive to the presence of volume defects such as bifilms and inclusions. The criterion was validated by studying the hot tearing tendency of Al-Cu alloy. In conformity with the experimental results, the new criterion predicted reduction of hot tearing tendency with increasing the copper content.

  6. The Criterion A problem revisited: controversies and challenges in defining and measuring psychological trauma.

    Science.gov (United States)

    Weathers, Frank W; Keane, Terence M

    2007-04-01

    The Criterion A problem in the field of traumatic stress refers to the stressor criterion for posttraumatic stress disorder (PTSD) and involves a number of fundamental issues regarding the definition and measurement of psychological trauma. These issues first emerged with the introduction of PTSD as a diagnostic category in the Diagnostic and Statistical Manual of Mental Disorders, Third Edition (DSM-III; American Psychiatric Association, 1980) and continue to generate considerable controversy. In this article, the authors provide an update on the Criterion A problem, with particular emphasis on the evolution of the DSM definition of the stressor criterion and the ongoing debate regarding broad versus narrow conceptualizations of traumatic events.

  7. Slope Safety Factor Calculations With Non-Linear Yield Criterion Using Finite Elements

    DEFF Research Database (Denmark)

    Clausen, Johan; Damkilde, Lars

    2006-01-01

    The factor of safety for a slope is calculated with the finite element method using a non-linear yield criterion of the Hoek-Brown type. The parameters of the Hoek-Brown criterion are found from triaxial test data. Parameters of the linear Mohr-Coulomb criterion are calibrated to the same triaxial...... are carried out at much higher stress levels than present in a slope failure, this leads to the conclusion that the use of the non-linear criterion leads to a safer slope design...

  8. Financial Key Ratios

    OpenAIRE

    Tănase Alin-Eliodor

    2014-01-01

    This article focuses on computing techniques starting from trial balance data regarding financial key ratios. There are presented activity, liquidity, solvency and profitability financial key ratios. It is presented a computing methodology in three steps based on a trial balance.

  9. RATIO_TOOL - SOFTWARE FOR COMPUTING IMAGE RATIOS

    Science.gov (United States)

    Yates, G. L.

    1994-01-01

    Geological studies analyze spectral data in order to gain information on surface materials. RATIO_TOOL is an interactive program for viewing and analyzing large multispectral image data sets that have been created by an imaging spectrometer. While the standard approach to classification of multispectral data is to match the spectrum for each input pixel against a library of known mineral spectra, RATIO_TOOL uses ratios of spectral bands in order to spot significant areas of interest within a multispectral image. Each image band can be viewed iteratively, or a selected image band of the data set can be requested and displayed. When the image ratios are computed, the result is displayed as a gray scale image. At this point a histogram option helps in viewing the distribution of values. A thresholding option can then be used to segment the ratio image result into two to four classes. The segmented image is then color coded to indicate threshold classes and displayed alongside the gray scale image. RATIO_TOOL is written in C language for Sun series computers running SunOS 4.0 and later. It requires the XView toolkit and the OpenWindows window manager (version 2.0 or 3.0). The XView toolkit is distributed with Open Windows. A color monitor is also required. The standard distribution medium for RATIO_TOOL is a .25 inch streaming magnetic tape cartridge in UNIX tar format. An electronic copy of the documentation is included on the program media. RATIO_TOOL was developed in 1992 and is a copyrighted work with all copyright vested in NASA. Sun, SunOS, and OpenWindows are trademarks of Sun Microsystems, Inc. UNIX is a registered trademark of AT&T Bell Laboratories.

  10. Spreading Sequence Design for Multiple Cell Synchronous DS-CDMA Systems under Total Weighted Squared Correlation Criterion

    Directory of Open Access Journals (Sweden)

    Cotae Paul

    2004-01-01

    Full Text Available An algorithm for designing spreading sequences for an overloaded multicellular synchronous DS-CDMA system on uplink is introduced. The criterion used to measure the optimality of the design is the total weighted square correlation (TWSC assuming the channel state information known perfectly at both transmitter and receiver. By using this algorithm it is possible to obtain orthogonal generalized WBE sequences sets for any processing gain. The bandwidth of initial generalized WBE signals of each cell is preserved in the extended signal space associated to multicellular system. Mathematical formalism is illustrated by selected numerical examples.

  11. Jet pairing algorithm for the 6-jet Higgs channel via energy chi-square criterion

    International Nuclear Information System (INIS)

    Magallanes, J.B.; Arogancia, D.C.; Gooc, H.C.; Vicente, I.C.M.; Bacala, A.M.; Miyamoto, A.; Fujii, K.

    2002-01-01

    Study and discovery of the Higgs bosons at JLC (Joint Linear Collider) is one of the tasks of ACFA (Asian Committee for future Accelerators)-JLC Group. The mode of Higgs production at JLC is e + e - → Z 0 H 0 . In this paper, studies are concentrated on the Higgsstrahlung process and the selection of its signals by getting the right jet-pairing algorithm of 6-jet final state at 300 GeV assuming that Higgs boson mass is 120 GeV and luminosity is 500 fb -1 . The total decay width Γ (H 0 → all) and the efficiency of the signals at the JLC are studied utilizing the 6-jet channel. Out of the 91,500 Higgsstrahlung events, 4,174 6-jet events are selected. PYTHIA Monte Carlo Generator generates the 6-jet Higgsstrahlung channel according to the Standard Model. The generated events are then simulated by Quick Simulator using the JCL parameters. After tagging all 6 quarks which correspond to the 6-jet final state of the Higgsstrahlung, the mean energy of the Z, H, and W's are obtained. Having calculated these information, the event energy chi-square is defined and it is found that the correct combination have generally smaller value. This criterion can be used to find correct jet-pairing algorithm and as one of the cuts for the background signals later on. Other chi-definitions are also proposed. (S. Funahashi)

  12. High Voltage Overhead Power Line Routing under an Objective Observability Criterion

    Directory of Open Access Journals (Sweden)

    L. Alfredo Fernandez-Jimenez

    2017-10-01

    Full Text Available The construction of new high voltage overhead power lines (HVOPLs has become a controversial issue for electricity companies due to social opposition. Citizens are concerned about how these power lines may have an impact on their lives, basically caused by their effects on health and safety. Visual impact is one of the most easily perceived. Although there are several published works that deal with the assessment of the visual impact produced by HVOPLs, no methodology has been proposed to assess this impact from an objective perspective. This work presents an original methodology which helps to identify the optimal routes for a new HVOPL under an objective observability criterion, enabling the selection of those with the lowest visibility in a zone. The application of the proposed methodology achieves a set of routes that links new HVOPL origin and destination points creating a corridor which includes all possible routes with an observability of its towers under a threshold limit. This methodology is illustrated by a real-life use corresponding to the selection of the route with least observability for a new power line in La Rioja (Spain. The results obtained may help to achieve a consensus between key stakeholders since it is focused on the specific issues of the planned HVOPL and its observability from an objective perspective.

  13. Ginzburg criterion for ionic fluids: the effect of Coulomb interactions.

    Science.gov (United States)

    Patsahan, O

    2013-08-01

    The effect of the Coulomb interactions on the crossover between mean-field and Ising critical behavior in ionic fluids is studied using the Ginzburg criterion. We consider the charge-asymmetric primitive model supplemented by short-range attractive interactions in the vicinity of the gas-liquid critical point. The model without Coulomb interactions exhibiting typical Ising critical behavior is used to calibrate the Ginzburg temperature of the systems comprising electrostatic interactions. Using the collective variables method, we derive a microscopic-based effective Hamiltonian for the full model. We obtain explicit expressions for all the relevant Hamiltonian coefficients within the framework of the same approximation, i.e., the one-loop approximation. Then we consistently calculate the reduced Ginzburg temperature t(G) for both the purely Coulombic model (a restricted primitive model) and the purely nonionic model (a hard-sphere square-well model) as well as for the model parameters ranging between these two limiting cases. Contrary to the previous theoretical estimates, we obtain the reduced Ginzburg temperature for the purely Coulombic model to be about 20 times smaller than for the nonionic model. For the full model including both short-range and long-range interactions, we show that t(G) approaches the value found for the purely Coulombic model when the strength of the Coulomb interactions becomes sufficiently large. Our results suggest a key role of Coulomb interactions in the crossover behavior observed experimentally in ionic fluids as well as confirm the Ising-like criticality in the Coulomb-dominated ionic systems.

  14. Communication and general concern criterion prior to activation of the rapid response team: a grounded theory.

    Science.gov (United States)

    Martland, Jarrad; Chamberlain, Diane; Hutton, Alison; Smigielski, Michael

    2016-11-01

    Objective Patients commonly show signs and symptoms of deterioration for hours or days before cardiorespiratory arrest. Rapid response teams (RRT) were created to improve recognition and response to patient deterioration in these situations. Activation criteria include vital signs or 'general concern' by a clinician or family member. The general concern criterion for RRT activation accounts for nearly one-third of all RRT activity, and although it is well established that communication deficits between staff can contribute to poorer outcomes for patients, there is little evidence pertaining to communication and its effects on the general concern RRT activation. Thus, the aim of the present study was to develop a substantive grounded theory related to the communication process between clinicians that preceded the activation of an RRT when general concern criterion was used. Methods Qualitative grounded theory involved collection of three types of data details namely personal notes from participants in focus groups with white board notes from discussions and audio recordings of the focus groups sessions. Focus groups were conducted with participants exploring issues associated with clinician communication and how it related to the activation of an RRT using the general concern criterion. Results The three main phases of coding (i.e. open, axial and selective coding) analysis identified 322 separate open codes. The strongest theme contributed to a theory of ineffective communication and decreased psychological safety, namely that 'In the absence of effective communication there is a subsequent increase in anxiety, fear or concern that can be directly attributed to the activation of an RRT using the 'general concern' criterion'. The RRT filled cultural and process deficiencies in the compliance with an escalation protocol. Issues such as 'not for resuscitation documentation' and 'inability to establish communication with and between medical or nursing personnel' rated

  15. Evidence for the Criterion Validity and Clinical Utility of the Pathological Narcissism Inventory

    Science.gov (United States)

    Thomas, Katherine M.; Wright, Aidan G. C.; Lukowitsky, Mark R.; Donnellan, M. Brent; Hopwood, Christopher J.

    2012-01-01

    In this study, the authors evaluated aspects of criterion validity and clinical utility of the grandiosity and vulnerability components of the Pathological Narcissism Inventory (PNI) using two undergraduate samples (N = 299 and 500). Criterion validity was assessed by evaluating the correlations of narcissistic grandiosity and narcissistic…

  16. The Bohm Criterion for Radiofrequency Discharges - a Numerical Verification Based on Poisson Equation

    NARCIS (Netherlands)

    Meijer, P. M.; W. J. Goedheer,

    1993-01-01

    Recently it was shown that, by using the analysis of electrostatic waves entering the plasma-sheath edge, the direct-current (dc) Bohm criterion also holds for discharges under radio-frequency (rf) conditions. In this paper, the influence of Bohm's criterion on the sheath characteristics for

  17. A Controlled Evaluation of the Distress Criterion for Binge Eating Disorder

    Science.gov (United States)

    Grilo, Carlos M.; White, Marney A.

    2011-01-01

    Objective: Research has examined various aspects of the validity of the research criteria for binge eating disorder (BED) but has yet to evaluate the utility of Criterion C, "marked distress about binge eating." This study examined the significance of the marked distress criterion for BED using 2 complementary comparison groups. Method:…

  18. Elaboration of generalized criterion for zonality determination of the Chernobyl' NPP working spaces

    International Nuclear Information System (INIS)

    Simakov, A.V.; Bad'in, V.I.; Nosovskij, A.V.

    1992-01-01

    Analysis of the features of radioactive dose rating, regularities of their formation and dosimetry allows suggesting generalized criterion for assess zonality of compartments and territories, combining all factors and their action on operators. This criterion may be used during design of the new objects, development of programs and pursuance of work on removal of atomic power plants from operation. 6 refs.; 1 fig

  19. Elitism, Sharing and Ranking Choices in Evolutionary Multi-Criterion Optimisation

    OpenAIRE

    Pursehouse, R.C.; Fleming, P.J.

    2002-01-01

    Elitism and sharing are two mechanisms that are believed to improve the performance of an evolutionary multi-criterion optimiser. The relative performance of of the two most popular ranking strategies is largely unknown. Using a new empirical inquiry framework, this report studies the effect of elitism, sharing and ranking design choices using a benchmark suite of two-criterion problems.........

  20. A new risk-based screening criterion for treatment-demanding retinopathy of prematurity in Denmark

    DEFF Research Database (Denmark)

    Slidsborg, Carina; Forman, Julie Lyng; Rasmussen, Steen Christian

    2011-01-01

    The aim of this study was to uncover the most effective and safe criterion to implement for retinopathy of prematurity screening in Denmark.......The aim of this study was to uncover the most effective and safe criterion to implement for retinopathy of prematurity screening in Denmark....

  1. An Integrated Pruning Criterion for Ensemble Learning Based on Classification Accuracy and Diversity

    DEFF Research Database (Denmark)

    Fu, Bin; Wang, Zhihai; Pan, Rong

    2013-01-01

    be further considered while designing a pruning criterion is presented, and then an effective definition of diversity is proposed. The experimental results have validated that the given pruning criterion could single out the subset of classifiers that show better performance in the process of hill...

  2. Effects of Mastery Criterion on the Emergence of Derived Equivalence Relations

    Science.gov (United States)

    Fienup, Daniel M.; Brodsky, Julia

    2017-01-01

    In this study, we manipulated mastery criterion form (rolling or block) and stringency (across 6 or 12 trials) and measured the emergence of derived relations. College students learned neuroanatomy equivalence classes and experienced one of two rolling mastery criteria (6 or 12 consecutive correct responses) or a block mastery criterion (12 trials…

  3. Energy-efficient induction motors designing with application of a modified criterion of reduced costs

    Directory of Open Access Journals (Sweden)

    V.S. Petrushin

    2014-03-01

    Full Text Available The paper introduces a modified criterion of reduced costs that employs coefficients of operation significance and priority of ohmic loss accounting to allow matching maximum efficiency with minimum reduced costs. Impact of the inflation factor on the criterion of reduced costs is analyzed.

  4. The New DSM-5 Impairment Criterion: A Challenge to Early Autism Spectrum Disorder Diagnosis?

    Science.gov (United States)

    Zander, Eric; Bölte, Sven

    2015-01-01

    The possible effect of the DSM-5 impairment criterion on diagnosing autism spectrum disorder (ASD) in young children was examined in 127 children aged 20-47 months with a DSM-IV-TR clinical consensus diagnosis of ASD. The composite score of the Vineland Adaptive Behavior Scales (VABS) served as a proxy for the DSM-5 impairment criterion. When…

  5. VVER-1000 dominance ratio

    International Nuclear Information System (INIS)

    Gorodkov, S.

    2009-01-01

    Dominance ratio, or more precisely, its closeness to unity, is important characteristic of large reactor. It allows evaluate beforehand the number of source iterations required in deterministic calculations of power spatial distribution. Or the minimal number of histories to be modeled for achievement of statistical error level desired in large core Monte Carlo calculations. In this work relatively simple approach for dominance ratio evaluation is proposed. It essentially uses core symmetry. Dependence of dominance ratio on neutron flux spatial distribution is demonstrated. (author)

  6. WWER-1000 dominance ratio

    International Nuclear Information System (INIS)

    Gorodkov, S.S.

    2009-01-01

    Dominance ratio, or more precisely, its closeness to unity, is important characteristic of large reactor. It allows evaluate beforehand the number of source iterations required in deterministic calculations of power spatial distribution. Or the minimal number of histories to be modeled for achievement of statistical error level desired in large core Monte Carlo calculations. In this work relatively simple approach for dominance ratio evaluation is proposed. It essentially uses core symmetry. Dependence of dominance ratio on neutron flux spatial distribution is demonstrated. (Authors)

  7. Generalized Majority Logic Criterion to Analyze the Statistical Strength of S-Boxes

    Science.gov (United States)

    Hussain, Iqtadar; Shah, Tariq; Gondal, Muhammad Asif; Mahmood, Hasan

    2012-05-01

    The majority logic criterion is applicable in the evaluation process of substitution boxes used in the advanced encryption standard (AES). The performance of modified or advanced substitution boxes is predicted by processing the results of statistical analysis by the majority logic criteria. In this paper, we use the majority logic criteria to analyze some popular and prevailing substitution boxes used in encryption processes. In particular, the majority logic criterion is applied to AES, affine power affine (APA), Gray, Lui J, residue prime, S8 AES, Skipjack, and Xyi substitution boxes. The majority logic criterion is further extended into a generalized majority logic criterion which has a broader spectrum of analyzing the effectiveness of substitution boxes in image encryption applications. The integral components of the statistical analyses used for the generalized majority logic criterion are derived from results of entropy analysis, contrast analysis, correlation analysis, homogeneity analysis, energy analysis, and mean of absolute deviation (MAD) analysis.

  8. Energy-Based Design Criterion of Dissipative Bracing Systems for the Seismic Retrofit of Frame Structures

    Directory of Open Access Journals (Sweden)

    Gloria Terenzi

    2018-02-01

    Full Text Available Direct sizing criteria represent useful tools in the design of dissipative bracing systems for the advanced seismic protection of existing frame structures, especially when incorporated dampers feature a markedly non-linear behaviour. An energy-based procedure is proposed herein to this aim, focusing attention on systems including fluid viscous devices. The procedure starts by assuming prefixed reduction factors of the most critical response parameters in current conditions, which are evaluated by means of a conventional elastic finite element analysis. Simple formulas relating the reduction factors to the equivalent viscous damping ratio of the dampers, ξeq, are proposed. These formulas allow calculating the ξeq values that guarantee the achievement of the target factors. Finally, the energy dissipation capacity of the devices is deduced from ξeq, finalizing their sizing process. A detailed description of the procedure is presented in the article, by distinguishing the cases where the prevailing structural deficiencies are represented by poor strength of the constituting members, from the cases having excessive horizontal displacements. A demonstrative application to the retrofit design of a reinforced concrete gym building is then offered to explicate the steps of the sizing criterion in practice, as well as to evaluate the enhancement of the seismic response capacities generated by the installation of the dissipative system.

  9. Magnetic properties of 2D nickel nanostrips: structure dependent magnetism and Stoner criterion

    International Nuclear Information System (INIS)

    Kashid, Vikas; Shah, Vaishali; Salunke, H G; Mokrousov, Yuriy; Blügel, Stefan

    2015-01-01

    We have investigated different geometries of two-dimensional (2D) infinite length Ni nanowires of increasing width using spin density functional theory calculations. Our simulations demonstrate that the parallelogram motif is the most stable and structures that incorporate the parallelogram motif are more stable as compared to rectangular structures. The wires are conducting and the conductance channels increase with increasing width. The wires have a non-linear behavior in the ballistic anisotropic magnetoresistance ratios (BAMR) with respect to the magnetization directions. All 2D nanowires as well as Ni (1 1 1) and Ni (1 0 0) monolayer investigated are ferromagnetic under the Stoner criterion and exhibit enhanced magnetic moments as compared to bulk Ni and the respective Ni monolayers. The easy axis for all nickel nanowires under investigation is observed to be along the wire axis. The double rectangular nanowire exhibits a magnetic anomaly with a smaller magnetic moment when compared to Ni (1 0 0) monolayer and is the only structure with an easy axis perpendicular to the wire axis. The Stoner parameter which has been known to be structure independent in bulk and surfaces is found to vary with the structure and the width of the nanowires. The less stable rectangular and rhombus shaped nanowires have a higher ferromagnetic strength than parallelogram shaped nanowires. (paper)

  10. Sharpening Sharpe Ratios

    OpenAIRE

    William N. Goetzmann; Jonathan E. Ingersoll Jr.; Matthew I. Spiegel; Ivo Welch

    2002-01-01

    It is now well known that the Sharpe ratio and other related reward-to-risk measures may be manipulated with option-like strategies. In this paper we derive the general conditions for achieving the maximum expected Sharpe ratio. We derive static rules for achieving the maximum Sharpe ratio with two or more options, as well as a continuum of derivative contracts. The optimal strategy has a truncated right tail and a fat left tail. We also derive dynamic rules for increasing the Sharpe ratio. O...

  11. Multi-criteria Ranking Under Pareto Inclusive Criterion of Preference: An Application in Ranking Some Fungi Species with Respect to Their Toxicity

    Directory of Open Access Journals (Sweden)

    Gniadek Agnieszka

    2014-12-01

    Full Text Available This study aims at demonstrating the usefulness of the Pareto in- clusive criterion methodology for comparative analyses of fungi toxicity. The toxicity of fungi is usually measured using a scale of several ranks. In practice, the ranks of toxicity are routinely grouped into only four conventional classes of toxicity: from a class of no toxicity, low toxicity, and moderate toxicity, to a class of high toxicity. The illustrative material included the N = 61 fungi samples obtained from three species: A. ochraceus, A. niger and A. flavus. In accordance with the Pareto approach, four partial criterions of the worst toxi- city were defined, a single criterion used for each conventional class of toxicity. Finally, the odds ratios (OR were calculated separately for each partial cri- terion, and the significance of the hypotheses OR = 1 was estimated. It was stated that A. ochraceus fungi are distinctly more toxic than the two remaining ones with respect to the all considered four partial criterions, with significance equal to p = 0.04, p = 0.04, p = 0.007 and p = 0.005, respectively. Thus, the suggested method illustrated its utility in the case under study.

  12. Development of a stress-induced martensitic transformation criterion for a Cu–Al–Be polycrystalline shape memory alloy undergoing uniaxial tension

    International Nuclear Information System (INIS)

    García-Castillo, F.N.; Cortés-Pérez, J.; Amigó, V.; Sánchez-Arévalo, F.M.; Lara-Rodríguez, G.A.

    2015-01-01

    This study presents a criterion for predicting the martensitic variants (MVs) that appear during the stress-induced martensitic transformation (SIMT) in a polycrystalline sample of Cu–11.5% wt. Al–0.5% wt. Be under simple tension. Our criterion is based on crystallographic parameters, such as the crystal orientation and Schmid factor (SF). The displacement vector fields (DVFs) were obtained in the observation system by a mathematical model and were used to distort the boundary of a set of grains. From the DVF, the strain tensor for each grain was obtained, and the strain ratio (SR) in the observation system was calculated. Electron backscattering diffraction (EBSD) measurements were performed to determine the crystal orientation of the grains. The inverse SF was used to determine the in-plane stress transformation diagrams (STDs) for each studied grain. The combination of a balance criterion (BC) and STD provided a criterion that allowed us to predict the possible order of stress-induced MVs formed as a function of the crystal orientation and thermomechanical parameters of the shape memory alloy (SMA) with higher accuracy than when using the criteria separately. To validate our criteria, we tested other researchers’ published results. Our results were in agreement and were capable of predicting the stress-induced MVs in a polycrystalline SMA

  13. FURTHER EVIDENCE OF AN ASSOCIATION BETWEEN LOW SECOND-TO-FOURTH DIGIT RATIO (2D:4D) AND SELECTION FOR THE UNIFORMED SERVICES: A STUDY AMONG POLICE PERSONNEL IN WROCŁAW, POLAND.

    Science.gov (United States)

    Kozieł, Sławomir; Kociuba, Marek; Chakraborty, Raja; Sitek, Aneta; Ignasiak, Zofia

    2017-08-22

    Males and females differ in their preference for occupations and sporting activities, and differ also in risk-taking attitudes. In addition to other explanations, prenatal hormone exposure has been implicated in these gender-associated differences. The ratio of the relative lengths of the second-to-fourth digits (2D:4D) is a proxy indicator of prenatal exposure to testosterone relative to oestrogen. The 2D:4D ratio has been found to be associated with choice of occupation, particularly among females. This study investigated whether 2D:4D differed between police officers and a control group of civilians in Wrocław, Poland. Participants were 147 male and 55 female police officers and 91 male and 75 female civilian controls. The police officers had to undergo rigorous physical ability tests during recruitment and their job bore relatively higher risk, whereas the controls had a normal civilian lifestyle. Height, weight, hand grip strength and lengths of the second and fourth digits were measured. Analyses of variance and covariance were employed to assess the significance of difference in digit ratio between groups (police officers and civilians) allowing for interaction with sex. The policewomen, compared with the female controls, were taller and had stronger hand grip strength, but had lower 2D:4D in the right hand and average 2D:4D of both hands. However, male and female police officers slightly differed only in the right hand digit ratio but not in the left hand ratio or the average for the two hands. However, the control group showed significant sex differences in all digit ratios with higher (feminine) mean values in females. The study provides further evidence that prenatal testosterone exposure, as reflected in the 2D:4D ratio, might have an association with choice of occupation, particularly among females.

  14. Detecting isotopic ratio outliers

    International Nuclear Information System (INIS)

    Bayne, C.K.; Smith, D.H.

    1985-01-01

    An alternative method is proposed for improving isotopic ratio estimates. This method mathematically models pulse-count data and uses iterative reweighted Poisson regression to estimate model parameters to calculate the isotopic ratios. This computer-oriented approach provides theoretically better methods than conventional techniques to establish error limits and to identify outliers. 6 refs., 3 figs., 3 tabs

  15. Detecting isotopic ratio outliers

    Science.gov (United States)

    Bayne, C. K.; Smith, D. H.

    An alternative method is proposed for improving isotopic ratio estimates. This method mathematically models pulse-count data and uses iterative reweighted Poisson regression to estimate model parameters to calculate the isotopic ratios. This computer-oriented approach provides theoretically better methods than conventional techniques to establish error limits and to identify outliers.

  16. Detecting isotopic ratio outliers

    International Nuclear Information System (INIS)

    Bayne, C.K.; Smith, D.H.

    1986-01-01

    An alternative method is proposed for improving isotopic ratio estimates. This method mathematically models pulse-count data and uses iterative reweighted Poisson regression to estimate model parameters to calculate the isotopic ratios. This computer-oriented approach provides theoretically better methods than conventional techniques to establish error limits and to identify outliers

  17. A Method to Establishing Tube Plugging Criterion for Heat Exchangers with Straight Tubes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyungnam [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    The difference of thermal expansion coefficients between the shell and tube materials causes the stress in axial direction of tube. Because of the axial stress due to thermal load, the straight tubes are used for heat exchangers operated in low temperature such as CCW (Component Cooling Water) heat exchangers and condensers. It is inevitable for the materials of the components to be degraded as the power plants become older. The degradation accompanies increasing maintenance cost as well as creating safety issues. The materials and wall thickness of heat exchanger tubes in nuclear power plants are selected to withstand system temperature, pressure, and corrosion. There are many codes and standards to be referred for calculating the minimum thickness of the heat exchanger tube in the designing stage. However, the codes and standards related to show the tube plugging criteria may not exist currently. In this paper, a method to establish the tube plugging criteria of BOP heat exchangers, which is based on the USNRC Regulatory Guide 1.121, is introduced and the tube plugging criteria for the TPCCW heat exchanger of Yonggwang NPP No. 1 and 2. A method to establish the tube plugging criteria of heat exchangers with straight tubes are introduced based on the USNRC Regulatory Guide 1.121. As an example, the tube plugging criterion for the CCW heat exchanger of a nuclear power plant is provided.

  18. Sensitive criterion for chirality; Chiral doublet bands in 104Rh59

    International Nuclear Information System (INIS)

    Koike, T.; Starosta, K.; Vaman, C.; Ahn, T.; Fossan, D.B.; Clark, R.M.; Cromaz, M.; Lee, I.Y.; Macchiavelli, A.O.

    2003-01-01

    A particle plus triaxial rotor model was applied to odd-odd nuclei in the A ∼ 130 region in order to study the unique parity πh11/2xνh11/2 rotational bands. With maximum triaxiality assumed and the intermediate axis chosen as the quantization axis for the model calculations, the two lowest energy eigenstates of a given spin have chiral properties. The independence of the quantity S(I) on spin can be used as a new criterion for chirality. In addition, a diminishing staggering amplitude of S(I) with increasing spin implies triaxiality in neighboring odd-A nuclei. Chiral quartet bases were constructed specifically to examine electromagnetic properties for chiral structures. A set of selection rules unique to chirality was derived. Doublet bands built on the πg9/2xνh11/2 configuration have been discovered in odd-odd 104Rh using the 96Zr(11B, 3n) reaction. Based on the discussed criteria for chirality, it is concluded that the doublet bands observed in 104Rh exhibit characteristic chiral properties suggesting a new region of chirality around A ∼110. In addition, magnetic moment measurements have been performed to test the πh11/2xνh11/2 configuration in 128Cs and the πg9/2xνh11/2 configuration in 104Rh

  19. Emotional intelligence: an admission criterion alternative to cumulative grade point averages for prelicensure students.

    Science.gov (United States)

    Jones-Schenk, Jan; Harper, Mary G

    2014-03-01

    Predicting potential student success is of great interest to nursing educators and academic administrators alike. Cumulative grade point average (CGPA) has traditionally been used to screen nursing program candidates, but CGPA itself has shown to have no statistically significant predictive value and may in fact screen out individuals who possess social intelligence attributes that are essential for success in nursing practice. The purpose of this study is to determine if students whose emotional intelligence characteristics meet or exceed those of successful staff nurses are more likely to be successful in a baccalaureate nursing program. A descriptive, correlational design was used to compare the emotional intelligence attributes of 116 potential nursing students and 42 successful staff nurses using the Emotional Quotient Inventory (EQ-i). Nursing students who remained in the nursing program were found to have significantly higher levels of total emotional intelligence, interpersonal capacity, and stress tolerance. Students who dropped from the nursing program were not significantly different from successful staff nurses in terms of emotional intelligence. Emotional intelligence presents a compelling adjunct to current selection criteria for nursing students. However, the lack of research prevents widespread adoption of this criterion. This study suggests that students with higher levels of emotional intelligence, particularly intrapersonal capacity and stress tolerance, are more likely to be successful in a baccalaureate nursing program than students with lower levels. Further research is needed to determine the usefulness of EI as a predictor of student success in nursing programs. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Analytical Solution of Tunnel Surrounding Rock for Stress and Displacement Based on Lade–Duncan Criterion

    Directory of Open Access Journals (Sweden)

    MingZheng Zhu

    2018-01-01

    Full Text Available The deformation and failure of tunnel surrounding rock is the result of tunnel excavation disturbance and rock stress release. When the local stress of surrounding rock exceeds the elastic limit of rock mass, the plastic analysis of surrounding rock must be carried out to judge the stability of tunnel. In this study, the Lade–Duncan yield criterion is used to calculate the analytic solutions for the surrounding rock in a tunnel, and the radius and displacement of the plastic zone are deduced using an equilibrium equation. The plastic zone radius and displacement based on Lade–Duncan criterion and Mohr–Coulomb criterion were compared by using single-factor analysis method under the different internal friction angles, in situ stresses, and support resistances. The results show that the solutions of the radius and displacement of plastic zone calculated by the Lade–Duncan criterion are close to those of Mohr–Coulomb criterion under the high internal friction angle and support resistance or low in situ rock stress; however, the radius and displacement of the plastic zone calculated by the Lade–Duncan criterion are larger under normal circumstances, and the Lade–Duncan criterion is more applicable to the stability analysis of the surrounding rock in a tunnel.

  1. Methods and criterions for IV generation system choice

    International Nuclear Information System (INIS)

    Carre, F; Fiorini, G. L.

    2005-01-01

    The international forum of IV generation has been built up in 2000, initiated by the American Energy Department with an initial participation of nine countries (and of ten today). In a primary phase of these works, which was finished in October 2002, the forum objects were to define the list of nuclear systems conditions which could be ready to use in 2030 to make a sustainable energy development, and select previously the most promising technology to attain these purposes. This article presents, with its trumps and limits, the methodology which was used to select, starting from 120 propositions, one set of 6 systems which includes key technologies for the nuclears of the 21st century. (Authors)

  2. Portfolio selection with heavy tails

    NARCIS (Netherlands)

    Hyung, N.; Vries, de C.G.

    2007-01-01

    Consider the portfolio problem of choosing the mix between stocks and bonds under a downside risk constraint. Typically stock returns exhibit fatter tails than bonds corresponding to their greater downside risk. Downside risk criteria like the safety first criterion therefore often select corner

  3. Difference and ratio plots

    DEFF Research Database (Denmark)

    Svendsen, Anders Jørgen; Holmskov, U; Bro, Peter

    1995-01-01

    and systemic lupus erythematosus from another previously published study (Macanovic, M. and Lachmann, P.J. (1979) Clin. Exp. Immunol. 38, 274) are also represented using ratio plots. Our observations indicate that analysis by regression analysis may often be misleading....... hitherto unnoted differences between controls and patients with either rheumatoid arthritis or systemic lupus erythematosus. For this we use simple, but unconventional, graphic representations of the data, based on difference plots and ratio plots. Differences between patients with Burkitt's lymphoma...

  4. Improved stochastic resonance algorithm for enhancement of signal-to-noise ratio of high-performance liquid chromatographic signal

    International Nuclear Information System (INIS)

    Xie Shaofei; Xiang Bingren; Deng Haishan; Xiang Suyun; Lu Jun

    2007-01-01

    Based on the theory of stochastic resonance, an improved stochastic resonance algorithm with a new criterion for optimizing system parameters to enhance signal-to-noise ratio (SNR) of HPLC/UV chromatographic signal for trace analysis was presented in this study. Compared with the conventional criterion in stochastic resonance, the proposed one can ensure satisfactory SNR as well as good peak shape of chromatographic peak in output signal. Application of the criterion to experimental weak signals of HPLC/UV was investigated and the results showed an excellent quantitative relationship between different concentrations and responses

  5. A criterion for testing hypotheses about the covariance function of a stationary Gaussian stochastic process

    OpenAIRE

    Kozachenko, Yuriy; Troshki, Viktor

    2015-01-01

    We consider a measurable stationary Gaussian stochastic process. A criterion for testing hypotheses about the covariance function of such a process using estimates for its norm in the space $L_p(\\mathbb {T}),\\,p\\geq1$, is constructed.

  6. A criterion of orthogonality on the assumption and restrictions in subgrid-scale modelling of turbulence

    Energy Technology Data Exchange (ETDEWEB)

    Fang, L. [LMP, Ecole Centrale de Pékin, Beihang University, Beijing 100191 (China); Co-Innovation Center for Advanced Aero-Engine, Beihang University, Beijing 100191 (China); Sun, X.Y. [LMP, Ecole Centrale de Pékin, Beihang University, Beijing 100191 (China); Liu, Y.W., E-mail: liuyangwei@126.com [National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics, School of Energy and Power Engineering, Beihang University, Beijing 100191 (China); Co-Innovation Center for Advanced Aero-Engine, Beihang University, Beijing 100191 (China)

    2016-12-09

    In order to shed light on understanding the subgrid-scale (SGS) modelling methodology, we analyze and define the concepts of assumption and restriction in the modelling procedure, then show by a generalized derivation that if there are multiple stationary restrictions in a modelling, the corresponding assumption function must satisfy a criterion of orthogonality. Numerical tests using one-dimensional nonlinear advection equation are performed to validate this criterion. This study is expected to inspire future research on generally guiding the SGS modelling methodology. - Highlights: • The concepts of assumption and restriction in the SGS modelling procedure are defined. • A criterion of orthogonality on the assumption and restrictions is derived. • Numerical tests using one-dimensional nonlinear advection equation are performed to validate this criterion.

  7. Entanglement criterion for tripartite systems based on local sum uncertainty relations

    Science.gov (United States)

    Akbari-Kourbolagh, Y.; Azhdargalam, M.

    2018-04-01

    We propose a sufficient criterion for the entanglement of tripartite systems based on local sum uncertainty relations for arbitrarily chosen observables of subsystems. This criterion generalizes the tighter criterion for bipartite systems introduced by Zhang et al. [C.-J. Zhang, H. Nha, Y.-S. Zhang, and G.-C. Guo, Phys. Rev. A 81, 012324 (2010), 10.1103/PhysRevA.81.012324] and can be used for both discrete- and continuous-variable systems. It enables us to detect the entanglement of quantum states without having a complete knowledge of them. Its utility is illustrated by some examples of three-qubit, qutrit-qutrit-qubit, and three-mode Gaussian states. It is found that, in comparison with other criteria, this criterion is able to detect some three-qubit bound entangled states more efficiently.

  8. On translational superfluidity and the Landau criterion for Bose gases in the Gross-Pitaevski limit

    International Nuclear Information System (INIS)

    Wreszinski, Walter F

    2008-01-01

    The two-fluid and Landau criteria for superfluidity are compared for trapped Bose gases. While the two-fluid criterion predicts translational superfluidity, it is suggested, on the basis of the homogeneous Gross-Pitaevski limit, that a necessary part of Landau's criterion, adequate for non-translationally invariant systems, does not hold for trapped Bose gases in the GP limit. As a consequence, if the compressibility is detected to be very large (infinite by experimental standards), the two-fluid criterion is seen to be the relevant one in case the system is a translational superfluid, while the Landau criterion is the relevant one if translational superfluidity is absent. (fast track communication)

  9. Ten Issues in Criterion-Referenced Testing: A Response to Commonly Heard Criticisms.

    Science.gov (United States)

    Curlette, William L.; Stallings, William M.

    1979-01-01

    The 10 criticisms of criterion-referenced tests addressed in this paper are: the domains tested; pedagogical influence; difficulty of items; cumbersome reports; reliability; arbitrary criteria; local objectives; labeling; predictive validity; and repeated testing. (SJL)

  10. Use of the Niyama criterion to predict porosity of the mushy zone with deformation

    Directory of Open Access Journals (Sweden)

    S. Polyakov

    2011-10-01

    Full Text Available The article presents new results on the use of the Niyama criterion to estimate porosity appearance in castings under hindered shrinkage. The effect of deformation of the mushy zone on filtration is shown. A new form of the Niyama criterion accounting for the hindered shrinkage and the range of deformation localization has been obtained. The results of this study are illustrated by the examp le of the Niyama criterion calculated for Al-Cu alloys under different diffusion conditions of solidification and rate of deformation in the mushy zone. Derived equations can be used in a mathematical model of the casting solidification as well as for interpretation of the simulation results of casting solidification under hindered shrinkage. The presented study resulted in a new procedure of using the Niyama criterion under mushy zone deformation.

  11. Relations Between Stressors and Job Performance: An Aggregate-Level Investigation Using Multiple Criterion Measures

    National Research Council Canada - National Science Library

    Thomas, Jeffrey

    2002-01-01

    .... Army Combat Brigades. Unlike previous studies that have focused exclusively on in-role performance, we examined relations between stressors and multiple performance criterion measures, which corresponded to in-role...

  12. TEMPERATURE-DEFORMATION CRITERION OF OPTIMIZATION OF FINE DRAWING HIGH CARBON WIRE ROUTE

    Directory of Open Access Journals (Sweden)

    Y. L. Bobarikin

    2012-01-01

    Full Text Available The temperature-deformation criterion of assessment and optimization of routes of the thin high-carbon wire drawing enabling to increase plastic properties of wire at retaining of its durability is offered.

  13. Criterion for the onset of quench for low-flow reflood

    International Nuclear Information System (INIS)

    Hsu, Y.Y.; Young, M.W.

    1982-07-01

    This study provides a criterion for the onset of quench for low flow reflood. The criterion is a combination of two conditions: T/sub clad/ < T/sub limiting quench/ where T = Temperature, and α < 0.95 where α = void fraction. This criterion was obtained by examining temperature data from tests simulating PWR reflood, such as FLECHT, THTF, PBF, CCTF, and FEBA tests, with void fraction data from CCTF, FEBA, and FLECHT low flood tests. The data show that quenching initiated at α = 0.95 and that the majority of quench occurred at void fractions near 0.85. The results show that rods can be completely quenched by entrained droplets even if the collapsed liquid level does not advance. A thorough discussion of the analysis which supports this quench criterion is given in the text of this report

  14. Assessing stress-related treatment needs among girls at risk for poor functional outcomes: The impact of cumulative adversity, criterion traumas, and non-criterion events.

    Science.gov (United States)

    Lansing, Amy E; Plante, Wendy Y; Beck, Audrey N

    2017-05-01

    Despite growing recognition that cumulative adversity (total stressor exposure, including complex trauma), increases the risk for psychopathology and impacts development, assessment strategies lag behind: Adversity-related mental health needs (symptoms, functional impairment, maladaptive coping) are typically assessed in response to only one qualifying Criterion-A traumatic event. This is especially problematic for youth at-risk for health and academic disparities who experience cumulative adversity, including non-qualifying events (separation from caregivers) which may produce more impairing symptomatology. Data from 118 delinquent girls demonstrate: (1) an average of 14 adverse Criterion-A and non-Criterion event exposures; (2) serious maladaptive coping strategies (self-injury) directly in response to cumulative adversity; (3) more cumulative adversity-related than worst-event related symptomatology and functional impairment; and (4) comparable symptomatology, but greater functional impairment, in response to non-Criterion events. These data support the evaluation of mental health needs in response to cumulative adversity for optimal identification and tailoring of services in high-risk populations to reduce disparities. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. A simple criterion for determining the static friction force between nanowires and flat substrates using the most-bent-state method.

    Science.gov (United States)

    Hou, Lizhen; Wang, Shiliang; Huang, Han

    2015-04-24

    A simple criterion was developed to assess the appropriateness of the currently available models that estimate the static friction force between nanowires and substrates using the 'most-bent-state' method. Our experimental testing of the static friction force between Al2O3 nanowires and Si substrate verified our theoretical analysis, as well as the establishment of the criterion. It was found that the models are valid only for the bent nanowires with the ratio of wire length over the minimum curvature radius [Formula: see text] no greater than 1. For the cases with [Formula: see text] greater than 1, the static friction force was overestimated as it neglected the effect of its tangential component.

  16. A second perspective on the Amann–Schmiedl–Seifert criterion for non-equilibrium in a three-state system

    International Nuclear Information System (INIS)

    Jia, Chen; Chen, Yong

    2015-01-01

    In the work of Amann, Schmiedl and Seifert (2010 J. Chem. Phys. 132 041102), the authors derived a sufficient criterion to identify a non-equilibrium steady state (NESS) in a three-state Markov system based on the coarse-grained information of two-state trajectories. In this paper, we present a mathematical derivation and provide a probabilistic interpretation of the Amann–Schmiedl–Seifert (ASS) criterion. Moreover, the ASS criterion is compared with some other criterions for a NESS. (paper)

  17. A Criterion for Stability of Synchronization and Application to Coupled Chua's Systems

    International Nuclear Information System (INIS)

    Wang Haixia; Lu Qishao; Wang Qingyun

    2009-01-01

    We investigate synchronization in an array network of nearest-neighbor coupled chaotic oscillators. By using of the Lyapunov stability theory and matrix theory, a criterion for stability of complete synchronization is deduced. Meanwhile, an estimate of the critical coupling strength is obtained to ensure achieving chaos synchronization. As an example application, a model of coupled Chua's circuits with linearly bidirectional coupling is studied to verify the validity of the criterion. (general)

  18. Nucleation of recrystallization in fine-grained materials: an extension of the Bailey-Hirsch criterion

    Science.gov (United States)

    Favre, Julien; Fabrègue, Damien; Chiba, Akihiko; Bréchet, Yves

    2013-11-01

    A new criterion for nucleation in the case of dynamic recrystallization is proposed in order to include the contribution of the grain boundary energy stored in the microstructure in the energy balance. Due to the nucleation events, the total surface area of pre-existing grain boundaries decreases, leading to a nucleus size smaller than expected by conventional nucleation criteria. The new model provides a better prediction of the nucleus size during recrystallization of pure copper compared with the conventional nucleation criterion.

  19. On global stability criterion for neural networks with discrete and distributed delays

    International Nuclear Information System (INIS)

    Park, Ju H.

    2006-01-01

    Based on the Lyapunov functional stability analysis for differential equations and the linear matrix inequality (LMI) optimization approach, a new delay-dependent criterion for neural networks with discrete and distributed delays is derived to guarantee global asymptotic stability. The criterion is expressed in terms of LMIs, which can be solved easily by various convex optimization algorithms. Some numerical examples are given to show the effectiveness of proposed method

  20. Relative criterion for validity of a semiclassical approach to the dynamics near quantum critical points.

    Science.gov (United States)

    Wang, Qian; Qin, Pinquan; Wang, Wen-ge

    2015-10-01

    Based on an analysis of Feynman's path integral formulation of the propagator, a relative criterion is proposed for validity of a semiclassical approach to the dynamics near critical points in a class of systems undergoing quantum phase transitions. It is given by an effective Planck constant, in the relative sense that a smaller effective Planck constant implies better performance of the semiclassical approach. Numerical tests of this relative criterion are given in the XY model and in the Dicke model.

  1. A novel delay-dependent criterion for delayed neural networks of neutral type

    International Nuclear Information System (INIS)

    Lee, S.M.; Kwon, O.M.; Park, Ju H.

    2010-01-01

    This Letter considers a robust stability analysis method for delayed neural networks of neutral type. By constructing a new Lyapunov functional, a novel delay-dependent criterion for the stability is derived in terms of LMIs (linear matrix inequalities). A less conservative stability criterion is derived by using nonlinear properties of the activation function of the neural networks. Two numerical examples are illustrated to show the effectiveness of the proposed method.

  2. A characterization of optimal portfolios under the tail mean-variance criterion

    OpenAIRE

    Owadally, I.; Landsman, Z.

    2013-01-01

    The tail mean–variance model was recently introduced for use in risk management and portfolio choice; it involves a criterion that focuses on the risk of rare but large losses, which is particularly important when losses have heavy-tailed distributions. If returns or losses follow a multivariate elliptical distribution, the use of risk measures that satisfy certain well-known properties is equivalent to risk management in the classical mean–variance framework. The tail mean–variance criterion...

  3. AUTOMATIC RECOGNITION OF FALLS IN GAIT-SLIP: A HARNESS LOAD CELL BASED CRITERION

    OpenAIRE

    Yang, Feng; Pai, Yi-Chung

    2011-01-01

    Over-head-harness systems, equipped with load cell sensors, are essential to the participants’ safety and to the outcome assessment in perturbation training. The purpose of this study was to first develop an automatic outcome recognition criterion among young adults for gait-slip training and then verify such criterion among older adults. Each of 39 young and 71 older subjects, all protected by safety harness, experienced 8 unannounced, repeated slips, while walking on a 7-m walkway. Each tri...

  4. A simple stability criterion for CANDU figure-of-eight flow oscillations

    International Nuclear Information System (INIS)

    Gulshani, P.; Spinks, N.J.

    1983-01-01

    Potential flow oscillations in CANDU reactor primary heat transport system are analyzed in terms of a simple, linearized model. A simple, algebraic stability criterion is obtained. The model predictions are found to be in good agreement with those of thermohydraulic codes for high pressure natural circulation conditions. For normal operating conditions the criterion predicts the correct trend but overlooks important stabilizing effects. The model clarifies the instability mechanism; namely the response of enthalpy and, hence, pressure in the boiling region to flow change

  5. Calculation of the residual bearing capacity of reinforced concrete beams by the rigidity (deflection) criterion

    OpenAIRE

    V.S. Utkin; S.A. Solovyov

    2015-01-01

    The article proposes the method of calculating the bearing capacity of reinforced concrete beams at the operational stage by the rigidity (deflection) criterion. The methods, which were used in the article, are integral test and probabilistic methods for describing random variables. The author offers a new technique of calculating a deflection limit by a criterion of residual deformations. The article exemplifies the usage of the evidence theory for statistical information processing in the f...

  6. Multiaxial fatigue criterion based on parameters from torsion and axial S-N curve

    Directory of Open Access Journals (Sweden)

    M. Margetin

    2016-07-01

    Full Text Available Multiaxial high cycle fatigue is a topic that concerns nearly all industrial domains. In recent years, a great deal of recommendations how to address problems with multiaxial fatigue life time estimation have been made and a huge progress in the field has been achieved. Until now, however, no universal criterion for multiaxial fatigue has been proposed. Addressing this situation, this paper offers a design of a new multiaxial criterion for high cycle fatigue. This criterion is based on critical plane search. Damage parameter consists of a combination of normal and shear stresses on a critical plane (which is a plane with maximal shear stress amplitude. Material parameters used in proposed criterion are obtained from torsion and axial S-N curves. Proposed criterion correctly calculates life time for boundary loading condition (pure torsion and pure axial loading. Application of proposed model is demonstrated on biaxial loading and the results are verified with testing program using specimens made from S355 steel. Fatigue material parameters for proposed criterion and multiple sets of data for different combination of axial and torsional loading have been obtained during the experiment.

  7. A new criterion of photostimulated luminescence (PSL) method to detect irradiated traditional Chinese medicinal herbs

    International Nuclear Information System (INIS)

    Zhang, Liwen; Lin, Tong; Jiang, Yingqiao; Bi, Fujun

    2013-01-01

    This work used a new criterion to analyze 162 varieties (222 batches) of traditional Chinese medicinal herbs based on the European Standard EN 13751 (2009. Foodstuffs—Detection of Irradiated Food Using Photostimulated Luminescence. European Committee for Standardization, Brussels, Belgium). The characteristics of PSL signals are described, and a new criterion is established. Compared to EN 13751, the new criterion uses clearer definition to evaluate instead of the ambiguous descriptions in EN Standard, such as “much greater than” and “within the same order of magnitude”. Moreover, the accuracy of the new criterion is as good as or better than EN Standard in regard to classifying irradiated and non-irradiated traditional Chinese medicinal herbs. It can help to avoid false positive result when a non-irradiated herb got a screening PSL measurement above 5000 counts/60 s. This new criterion of photostimulated luminescence method can be applied to identify the irradiation status of traditional Chinese medicinal herbs, even if the medicinal herbs were irradiated at a low dose (0.3 kGy) or stored in the dark at room temperature for 24 months after the irradiation treatment. - Highlights: • Clearer evaluation criterion instead of the ambiguous descriptions in EN 13751. • Accuracy satisfied. • Large sample size provides outstanding representativeness. • Systematical evaluation on PSL method

  8. A new repair criterion for steam generator tubes with axial cracks based on probabilistic integrity assessment

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyun-Su; Oh, Chang-Kyun [KEPCO Engineering and Construction Company, Inc., 269, Hyeoksin-ro, Gimcheon, Gyeongsangbuk-do 39660 (Korea, Republic of); Chang, Yoon-Suk, E-mail: yschang@khu.ac.kr [Department of Nuclear Engineering, College of Engineering, Kyung Hee University, 1732 Deokyoungdaero, Giheung, Yongin, Gyeonggi 446-701 (Korea, Republic of)

    2017-03-15

    Highlights: • Probabilistic assessment was performed for axially cracked steam generator tubes. • The threshold crack sizes were determined based on burst pressures of the tubes. • A new repair criterion was suggested as a function of operation time. - Abstract: Steam generator is one of the major components in a nuclear power plant, and it consists of thousands of thin-walled tubes. The operating record of the steam generators has indicated that a number of axial cracks due to stress corrosion have been frequently detected in the tubes. Since the tubes are closely related to the safety and also the efficiency of a nuclear power plant, an establishment of the appropriate repair criterion for the defected tubes and its applications are necessary. The objective of this paper is to develop an accurate repair criterion for the tubes with axial cracks. To do this, a thorough review is performed on the key parameters affecting the tube integrity, and then the probabilistic integrity assessment is carried out by considering the various uncertainties. In addition, the sizes of critical crack are determined by comparing the burst pressure of the cracked tube with the required performance criterion. Based on this result, the new repair criterion for the axially cracked tubes is defined from the reasonably conservative value such that the required performance criterion in terms of the burst pressure is able to be met during the next operating period.

  9. A critical analysis of the Mises stress criterion used in frequency domain fatigue life prediction

    Directory of Open Access Journals (Sweden)

    Adam Niesłony

    2016-10-01

    Full Text Available Multiaxial fatigue failure criteria are formulated in time and frequency domain. The number of frequency domain criteria is rather small and the most popular one is the equivalent von Mises stress criterion. This criterion was elaborated by Preumont and Piefort on the basis of well-known von Mises stress concept, first proposed by Huber in 1907, and well accepted by the scientific community and engineers. It is important to know, that the criterion was developed to determine the yield stress and material effort under static load. Therefore the direct use of equivalent von Mises stress criterion for fatigue life prediction can lead to some incorrectness of theoretical and practical nature. In the present study four aspects were discussed: influence of the value of fatigue strength of tension and torsion, lack of parallelism of the SN curves, abnormal behaviour of the criterion under biaxial tensioncompression and influence of phase shift between particular stress state components. Information contained in this article will help to prevent improper use of this criterion and contributes to its better understanding

  10. An improved criterion for new particle formation in diverse atmospheric environments

    Directory of Open Access Journals (Sweden)

    C. Kuang

    2010-09-01

    Full Text Available A dimensionless theory for new particle formation (NPF was developed, using an aerosol population balance model incorporating recent developments in nucleation rates and measured particle growth rates. Based on this theoretical analysis, it was shown that a dimensionless parameter LΓ, characterizing the ratio of the particle scavenging loss rate to the particle growth rate, exclusively determined whether or not NPF would occur on a particular day. This parameter determines the probability that a nucleated particle will grow to a detectable size before being lost by coagulation with the pre-existing aerosol. Cluster-cluster coagulation was shown to contribute negligibly to this survival probability under conditions pertinent to the atmosphere. Data acquired during intensive measurement campaigns in Tecamac (MILAGRO, Atlanta (ANARChE, Boulder, and Hyytiälä (QUEST II, QUEST IV, and EUCAARI were used to test the validity of LΓ as an NPF criterion. Measurements included aerosol size distributions down to 3 nm and gas-phase sulfuric acid concentrations. The model was applied to seventy-seven NPF events and nineteen non-events (characterized by growth of pre-existing aerosol without NPF measured in diverse environments with broad ranges in sulfuric acid concentrations, ultrafine number concentrations, aerosol surface areas, and particle growth rates (nearly two orders of magnitude. Across this diverse data set, a nominal value of LΓ=0.7 was found to determine the boundary for the occurrence of NPF, with NPF occurring when LΓ<0.7 and being suppressed when LΓ>0.7. Moreover, nearly 45% of measured LΓ values associated with NPF fell in the relatively narrow range of 0.1<LΓ<0.3.

  11. Performance and environment as objectives in multi-criterion optimization of steam injected gas turbine cycles

    International Nuclear Information System (INIS)

    Kayadelen, Hasan Kayhan; Ust, Yasin

    2014-01-01

    Rapidly growing demand for gas turbines promotes research on their performance improvement and reducing their exhaust pollutants. Even small increments in net power or thermal efficiency and small changes in pollutant emissions have become significant concerns for both new designs and cycle modifications. To fulfill these requirements an accurate performance evaluation method which enables to see the effects on the exhaust gas composition is an important necessity. To fill this gap, a thermo-ecologic performance evaluation approach for gas turbine cycles with chemical equilibrium approximation which enables performance and environmental aspects to be considered simultaneously, is presented in this work. Steam injection is an effective modification to boost power and limit NO x emissions for gas turbine systems. Steam injection also increases thermal efficiency so less fuel is burnt to maintain the same power output. Because of its performance related and environmental advantages, presented approach is applied on the steam injected gas turbine cycle and a precise multi-criterion optimization is carried out for varying steam injection, as well as equivalence and pressure ratios. Irreversibilities and pressure losses are also considered. Effects of each parameter on the net work and thermal efficiency as well as non-equilibrium NO x and CO emissions are demonstrated. Precision improvement of the presented thermo-ecological model is shown and two main concerns; constant turbine inlet condition for higher net work output and constant net work output condition for lower fuel consumption are compared. - Highlights: • A thermodynamically precise performance estimation tool for GT cycles is presented. • STIG application is provided to show its flexibility for any GT cycle and diluents. • Constant TIT and net work output conditions have been compared and discussed. • The model provides results to evaluate economic and environmental aspects together. • It provides a

  12. Signal to Noise Ratio (SNR Enhancement Comparison of Impulse-, Coding- and Novel Linear-Frequency-Chirp-Based Optical Time Domain Reflectometry (OTDR for Passive Optical Network (PON Monitoring Based on Unique Combinations of Wavelength Selective Mirrors

    Directory of Open Access Journals (Sweden)

    Christopher M. Bentz

    2014-03-01

    Full Text Available We compare optical time domain reflectometry (OTDR techniques based on conventional single impulse, coding and linear frequency chirps concerning their signal to noise ratio (SNR enhancements by measurements in a passive optical network (PON with a maximum one-way attenuation of 36.6 dB. A total of six subscribers, each represented by a unique mirror pair with narrow reflection bandwidths, are installed within a distance of 14 m. The spatial resolution of the OTDR set-up is 3.0 m.

  13. Tau leptonic branching ratios

    CERN Document Server

    Buskulic, Damir; De Bonis, I; Décamp, D; Ghez, P; Goy, C; Lees, J P; Lucotte, A; Minard, M N; Odier, P; Pietrzyk, B; Ariztizabal, F; Chmeissani, M; Crespo, J M; Efthymiopoulos, I; Fernández, E; Fernández-Bosman, M; Gaitan, V; Garrido, L; Martínez, M; Orteu, S; Pacheco, A; Padilla, C; Palla, Fabrizio; Pascual, A; Perlas, J A; Sánchez, F; Teubert, F; Colaleo, A; Creanza, D; De Palma, M; Farilla, A; Gelao, G; Girone, M; Iaselli, Giuseppe; Maggi, G; Maggi, M; Marinelli, N; Natali, S; Nuzzo, S; Ranieri, A; Raso, G; Romano, F; Ruggieri, F; Selvaggi, G; Silvestris, L; Tempesta, P; Zito, G; Huang, X; Lin, J; Ouyang, Q; Wang, T; Xie, Y; Xu, R; Xue, S; Zhang, J; Zhang, L; Zhao, W; Bonvicini, G; Cattaneo, M; Comas, P; Coyle, P; Drevermann, H; Engelhardt, A; Forty, Roger W; Frank, M; Hagelberg, R; Harvey, J; Jacobsen, R; Janot, P; Jost, B; Kneringer, E; Knobloch, J; Lehraus, Ivan; Markou, C; Martin, E B; Mato, P; Minten, Adolf G; Miquel, R; Oest, T; Palazzi, P; Pater, J R; Pusztaszeri, J F; Ranjard, F; Rensing, P E; Rolandi, Luigi; Schlatter, W D; Schmelling, M; Schneider, O; Tejessy, W; Tomalin, I R; Venturi, A; Wachsmuth, H W; Wiedenmann, W; Wildish, T; Witzeling, W; Wotschack, J; Ajaltouni, Ziad J; Bardadin-Otwinowska, Maria; Barrès, A; Boyer, C; Falvard, A; Gay, P; Guicheney, C; Henrard, P; Jousset, J; Michel, B; Monteil, S; Montret, J C; Pallin, D; Perret, P; Podlyski, F; Proriol, J; Rossignol, J M; Saadi, F; Fearnley, Tom; Hansen, J B; Hansen, J D; Hansen, J R; Hansen, P H; Nilsson, B S; Kyriakis, A; Simopoulou, Errietta; Siotis, I; Vayaki, Anna; Zachariadou, K; Blondel, A; Bonneaud, G R; Brient, J C; Bourdon, P; Passalacqua, L; Rougé, A; Rumpf, M; Tanaka, R; Valassi, Andrea; Verderi, M; Videau, H L; Candlin, D J; Parsons, M I; Focardi, E; Parrini, G; Corden, M; Delfino, M C; Georgiopoulos, C H; Jaffe, D E; Antonelli, A; Bencivenni, G; Bologna, G; Bossi, F; Campana, P; Capon, G; Chiarella, V; Felici, G; Laurelli, P; Mannocchi, G; Murtas, F; Murtas, G P; Pepé-Altarelli, M; Dorris, S J; Halley, A W; ten Have, I; Knowles, I G; Lynch, J G; Morton, W T; O'Shea, V; Raine, C; Reeves, P; Scarr, J M; Smith, K; Smith, M G; Thompson, A S; Thomson, F; Thorn, S; Turnbull, R M; Becker, U; Braun, O; Geweniger, C; Graefe, G; Hanke, P; Hepp, V; Kluge, E E; Putzer, A; Rensch, B; Schmidt, M; Sommer, J; Stenzel, H; Tittel, K; Werner, S; Wunsch, M; Beuselinck, R; Binnie, David M; Cameron, W; Colling, D J; Dornan, Peter J; Konstantinidis, N P; Moneta, L; Moutoussi, A; Nash, J; San Martin, G; Sedgbeer, J K; Stacey, A M; Dissertori, G; Girtler, P; Kuhn, D; Rudolph, G; Bowdery, C K; Brodbeck, T J; Colrain, P; Crawford, G; Finch, A J; Foster, F; Hughes, G; Sloan, Terence; Whelan, E P; Williams, M I; Galla, A; Greene, A M; Kleinknecht, K; Quast, G; Raab, J; Renk, B; Sander, H G; Wanke, R; Van Gemmeren, P; Zeitnitz, C; Aubert, Jean-Jacques; Bencheikh, A M; Benchouk, C; Bonissent, A; Bujosa, G; Calvet, D; Carr, J; Diaconu, C A; Etienne, F; Thulasidas, M; Nicod, D; Payre, P; Rousseau, D; Talby, M; Abt, I; Assmann, R W; Bauer, C; Blum, Walter; Brown, D; Dietl, H; Dydak, Friedrich; Ganis, G; Gotzhein, C; Jakobs, K; Kroha, H; Lütjens, G; Lutz, Gerhard; Männer, W; Moser, H G; Richter, R H; Rosado-Schlosser, A; Schael, S; Settles, Ronald; Seywerd, H C J; Saint-Denis, R; Wolf, G; Alemany, R; Boucrot, J; Callot, O; Cordier, A; Courault, F; Davier, M; Duflot, L; Grivaz, J F; Heusse, P; Jacquet, M; Kim, D W; Le Diberder, F R; Lefrançois, J; Lutz, A M; Musolino, G; Nikolic, I A; Park, H J; Park, I C; Schune, M H; Simion, S; Veillet, J J; Videau, I; Abbaneo, D; Azzurri, P; Bagliesi, G; Batignani, G; Bettarini, S; Bozzi, C; Calderini, G; Carpinelli, M; Ciocci, M A; Ciulli, V; Dell'Orso, R; Fantechi, R; Ferrante, I; Foà, L; Forti, F; Giassi, A; Giorgi, M A; Gregorio, A; Ligabue, F; Lusiani, A; Marrocchesi, P S; Messineo, A; Rizzo, G; Sanguinetti, G; Sciabà, A; Spagnolo, P; Steinberger, Jack; Tenchini, Roberto; Tonelli, G; Triggiani, G; Vannini, C; Verdini, P G; Walsh, J; Betteridge, A P; Blair, G A; Bryant, L M; Cerutti, F; Gao, Y; Green, M G; Johnson, D L; Medcalf, T; Mir, L M; Perrodo, P; Strong, J A; Bertin, V; Botterill, David R; Clifft, R W; Edgecock, T R; Haywood, S; Edwards, M; Maley, P; Norton, P R; Thompson, J C; Bloch-Devaux, B; Colas, P; Emery, S; Kozanecki, Witold; Lançon, E; Lemaire, M C; Locci, E; Marx, B; Pérez, P; Rander, J; Renardy, J F; Roussarie, A; Schuller, J P; Schwindling, J; Trabelsi, A; Vallage, B; Johnson, R P; Kim, H Y; Litke, A M; McNeil, M A; Taylor, G; Beddall, A; Booth, C N; Boswell, R; Cartwright, S L; Combley, F; Dawson, I; Köksal, A; Letho, M; Newton, W M; Rankin, C; Thompson, L F; Böhrer, A; Brandt, S; Cowan, G D; Feigl, E; Grupen, Claus; Lutters, G; Minguet-Rodríguez, J A; Rivera, F; Saraiva, P; Smolik, L; Stephan, F; Apollonio, M; Bosisio, L; Della Marina, R; Giannini, G; Gobbo, B; Ragusa, F; Rothberg, J E; Wasserbaech, S R; Armstrong, S R; Bellantoni, L; Elmer, P; Feng, Z; Ferguson, D P S; Gao, Y S; González, S; Grahl, J; Harton, J L; Hayes, O J; Hu, H; McNamara, P A; Nachtman, J M; Orejudos, W; Pan, Y B; Saadi, Y; Schmitt, M; Scott, I J; Sharma, V; Turk, J; Walsh, A M; Wu Sau Lan; Wu, X; Yamartino, J M; Zheng, M; Zobernig, G

    1996-01-01

    A sample of 62249 \\tau-pair events is selected from data taken with the ALEPH detector in 1991, 1992 and 1993. The measurement of the branching fractions for \\tau decays into electrons and muons is presented with emphasis on the study of systematic effects from selection, particle identification and decay classification. Combined with the most recent ALEPH determination of the \\tau lifetime, these results provide a relative measurement of the leptonic couplings in the weak charged current for transverse W bosons.

  14. The rectilinear Steiner ratio

    Directory of Open Access Journals (Sweden)

    PO de Wet

    2005-06-01

    Full Text Available The rectilinear Steiner ratio was shown to be 3/2 by Hwang [Hwang FK, 1976, On Steiner minimal trees with rectilinear distance, SIAM Journal on Applied Mathematics, 30, pp. 104– 114.]. We use continuity and introduce restricted point sets to obtain an alternative, short and self-contained proof of this result.

  15. Variation in water-use efficiency and its relation to carbon isotope ratio in cotton

    International Nuclear Information System (INIS)

    Saranga, Y.; Flash, I.; Yakir, D.

    1998-01-01

    Cotton (Gossypium spp.) is often exposed to drought, which adversely affects both yield and quality. Improved water-use efficiency (WUE = total dry matter produced or yield harvested / water used) is expected to reduce these adverse effects. Genetic variability in WUE and its association with photosynthetic rate and carbon isotope ratio (13C/12C) in cotton are reported in this paper. WUE of six cotton cultivars--G. hirsutum L., G. barbadense L., and an interspecific F1 hybrid (G. hirsutum x G. barbadense, ISH), was examined under two irrigation regimes in two field trials. The greatest WUE was obtained by two G. hirsutum cultivars (2.55 g dry matter or 1.12 g seed-cotton L-1 H2O) the ISH obtained similar or somewhat lower values, and that G. barbadense cultivars and one G. hirsutum cultivar exhibited the lowest values (2.1 g dry matter or 0.8 to 0.85 g seed-cotton L-1 H2O). These results indicate that different cotton cultivars may have evolved different environmental adaptations that affect their WUE. Photosynthetic rate was correlated with WUE in only a few cases emphasizing the limitation of this parameter as a basis for estimating crop WUE. Under both trials WUE was positively correlated with carbon isotope ratio, indicating the potential of this technique as a selection criterion for improving cotton WUE

  16. Three-Dimensional Dynamic Rupture in Brittle Solids and the Volumetric Strain Criterion

    Science.gov (United States)

    Uenishi, K.; Yamachi, H.

    2017-12-01

    As pointed out by Uenishi (2016 AGU Fall Meeting), source dynamics of ordinary earthquakes is often studied in the framework of 3D rupture in brittle solids but our knowledge of mechanics of actual 3D rupture is limited. Typically, criteria derived from 1D frictional observations of sliding materials or post-failure behavior of solids are applied in seismic simulations, and although mode-I cracks are frequently encountered in earthquake-induced ground failures, rupture in tension is in most cases ignored. Even when it is included in analyses, the classical maximum principal tensile stress rupture criterion is repeatedly used. Our recent basic experiments of dynamic rupture of spherical or cylindrical monolithic brittle solids by applying high-voltage electric discharge impulses or impact loads have indicated generation of surprisingly simple and often flat rupture surfaces in 3D specimens even without the initial existence of planes of weakness. However, at the same time, the snapshots taken by a high-speed digital video camera have shown rather complicated histories of rupture development in these 3D solid materials, which seem to be difficult to be explained by, for example, the maximum principal stress criterion. Instead, a (tensile) volumetric strain criterion where the volumetric strain (dilatation or the first invariant of the strain tensor) is a decisive parameter for rupture seems more effective in computationally reproducing the multi-directionally propagating waves and rupture. In this study, we try to show the connection between this volumetric strain criterion and other classical rupture criteria or physical parameters employed in continuum mechanics, and indicate that the criterion has, to some degree, physical meanings. First, we mathematically illustrate that the criterion is equivalent to a criterion based on the mean normal stress, a crucial parameter in plasticity. Then, we mention the relation between the volumetric strain criterion and the

  17. Input criterion for seismic analysis of nuclear power plants

    International Nuclear Information System (INIS)

    Gupta, D.C.; Agrawal, P.K.; Singh, S.

    1979-01-01

    This paper presents the results of a study made to assess the conservatism of applying the USNRC R.G. 1.60 spectrum at the foundation elevation in the free field. Two types of soil sites are investigated: (i) stiff soil site and (ii) deep cohesionless soil site. Several appropriate earthquake motions are selected such that the locations at which they were recorded are representative of the types of soil sites used in this study. The acceleration time histories of the recorded earthquake motions, scaled to the same peak acceleration (Asub(max) = 0.1 g), are applied at the surface and the resulting motions are obtained at various elevations in the free field. For each case, the soil properties are varied within a practical range (+- 50%). The resulting motions at various elevations are compared with the results obtained at the same elevations using the USNRC R.G. 1.60 spectrum for maximum ground acceleration equal to 0.1 g and applied at the foundation elevation. (orig.)

  18. A Fracture-Based Criterion for Debonding Strength of Adhesive-Bonded Double-Strap Steel Joints

    Directory of Open Access Journals (Sweden)

    Prawit Santisukpotha

    2012-01-01

    Full Text Available This paper addresses the debonding strength of adhesive-bonded double-strap steel joints. A fracture-based criterion was formulated in terms of a stress singularity parameter, i.e., the stress intensity factor, which governs the magnitude of a singular stress field near the joint ends. No existing crack was assumed. A total of 24 steel joint specimens were tested under constant amplitude fatigue loadings at stress ratio of 0.2 and frequency of 2 Hz. The joint stiffness ratio was slightly less than one to control the maximum adhesive stresses at the joint ends. To detect the debonding, a simple and practical technique was developed. The test results showed that the interfacial failure near the steel/adhesive corner was a dominant failure mode. The failure was brittle and the debonding life was governed by the crack initiation stage. The finite element analysis was employed to calculate the stress intensity factors and investigate the effects of the adhesive layer thickness, lap length and joint stiffness ratio on the debonding strength.

  19. A physically based criterion for hydraulic hazard mapping

    Science.gov (United States)

    Milanesi, Luca; Pilotti, Marco; Petrucci, Olga

    2013-04-01

    Hydraulic hazard maps are widely used for land use and emergency planning. Due to their practical consequences, it is important that their meaning is effectively transferred and shared by the stakeholders; to this purpose maps should communicate hazard levels moving from the potential consequences on specified targets. For these reasons flood maps showing only the extension of the inundated areas or flow features as depth and/or velocity may reveal themselves as ineffective instruments. The selection of the specific target to analyse must, in our opinion, be site-specific and reflect land use and/or the hydraulics features of the phenomenon. In case of sudden processes, such as torrential floods or debris flows, hazard levels should be referred to human life, because emergency plans may not mitigate risk; on the contrary, when the time scale of the flood wave propagation is sufficiently larger than the warning system one, the focus might move to the economic value of properties, since human-focused criteria may result in too severe land planning restrictions. This contribution starts exploring, from a theoretical point of view, human hazard levels as drowning, toppling and friction stability limits, which are the main failure mechanisms of human stability in flows. The proposed approach considers the human body, set on a slope and hit by a current of known density, as a combination of cylinders with different dimensions. The drowning threshold is identified through a limiting water depth, while toppling and translation are studied respectively through a moment and momentum balance. The involved forces are the friction at the bottom, the destabilizing drag force exerted by the current, the human weight and buoyancy. Several threshold curves on the velocity-depth plane can be identified as a function of different masses and heights for children and adults. Because of its dependence from the fluid density, this methodology may be applied also to define hazard

  20. Change in the alpha criterion policy: variable based on the maximum individual dose function

    International Nuclear Information System (INIS)

    Freitas Acosta Perez, C. de; Sordi, G.M.A.A.

    2006-01-01

    The Alpha value is an extremely important criterion because it determines the time that a country takes to achieve its proposals in order to decrease the workers doses involved with ionizing radiation sources. Currently the countries adopt a single value for alpha based on the annual gross national product, GNP, per capita. The aim of this paper is to show that the selection of a curve for the alpha in place of a single value would be more efficient. This curve would provide alpha values that would will be constraints to the biggest individual doses presented in each optimization process as applied both to designs and to operations. These maximum individual doses would represent the dose distribution among the workers team. To build the curve, the alpha values suggested are not based on the GNP per capita but on a distribution function of the maximum individual doses and on the time necessary to reach the proposal of 1/10 of the annual dose limit foreseen in the sequential optimization processes, that is to reach the region where the individual doses are considered acceptable. So, the differential equations will be - d X/dS =α(H m ax). To clarify our sight about the alpha value we started using the uranium mine example presented in ICRP publication 55, adopting the decision-aiding technique known as extended cost-benefit. for right. Then we used the same example in a hypothetical curve with portions: constant, linear, quadratic and exponential. Eventually we discussed briefly the different shapes of the curves that the alpha value can assume in function of the individual doses. Each of these shapes can correspond to the so called 'risk neutral attitude', 'risk adverse attitude' or 'risk prone attitude' suggested in the appendix B of the ICRP publication 55

  1. Tube Plugging Criterion for the TPCCW Heat Exchanger of Yonggwang NPP 1 and 2

    International Nuclear Information System (INIS)

    Kim, Hyung Nam; Yoo, Hyun Ju; Choi, Sung Nam; Song, Seok Yoon

    2009-01-01

    The turbine plant component cooling water(TPCCW) system circulates the cooling water to cool the components in the turbine building and discharges the heat from the components through the TPCCW heat exchanger. Recently, Yonggwang NPP 1 and 2 replaced the TPCCW heat exchanger because of tube degradation. The tubing material of new TPCCW heat exchanger of Yonggwang NPP 1 and 2 is titanium. If the tube wall cannot withstand the pressure, the cooling water with the chemicals flows into the tube side and it is discharged to the open water. The chemicals can pollute the open water. Therefore, the tubes of the TPCCW heat exchanger should be inspected and degraded tubes should be plugged. It is inevitable for the materials of the components to be degraded as the power plants become older. The degradation accompanies increasing maintenance cost as well as creating safety issues. The materials and wall thickness of heat exchanger tubes in nuclear power plants are selected to withstand system temperature, pressure, and corrosion. However, tubes have experienced leaks and failures and plugged based upon eddy current testing (ET) results. There are some problems for plugging the heat exchanger tubes since the criterion and its basis are not clearly described. For this reason, the criteria for the tube wall thickness are addressed in order to operate the heat exchangers in nuclear power plant without trouble during the cycle. There are many codes and standards to be referred for calculating the minimum thickness of the heat exchanger tube in the designing stage. However, the codes and standards related to show the tube plugging criteria may not exist currently. In this paper, a method to establish the tube plugging criteria of BOP heat exchangers, which is based on the USNRC Regulatory Guide 1.121, is introduced and the tube plugging criteria for the TPCCW heat exchanger of Yonggwang NPP No. 1 and 2. This method relies on the similar plugging criteria used in the steam generator

  2. Tube Plugging Criterion for the TPCCW Heat Exchanger of Yonggwang NPP 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyung Nam; Yoo, Hyun Ju; Choi, Sung Nam; Song, Seok Yoon [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

    2009-05-15

    The turbine plant component cooling water(TPCCW) system circulates the cooling water to cool the components in the turbine building and discharges the heat from the components through the TPCCW heat exchanger. Recently, Yonggwang NPP 1 and 2 replaced the TPCCW heat exchanger because of tube degradation. The tubing material of new TPCCW heat exchanger of Yonggwang NPP 1 and 2 is titanium. If the tube wall cannot withstand the pressure, the cooling water with the chemicals flows into the tube side and it is discharged to the open water. The chemicals can pollute the open water. Therefore, the tubes of the TPCCW heat exchanger should be inspected and degraded tubes should be plugged. It is inevitable for the materials of the components to be degraded as the power plants become older. The degradation accompanies increasing maintenance cost as well as creating safety issues. The materials and wall thickness of heat exchanger tubes in nuclear power plants are selected to withstand system temperature, pressure, and corrosion. However, tubes have experienced leaks and failures and plugged based upon eddy current testing (ET) results. There are some problems for plugging the heat exchanger tubes since the criterion and its basis are not clearly described. For this reason, the criteria for the tube wall thickness are addressed in order to operate the heat exchangers in nuclear power plant without trouble during the cycle. There are many codes and standards to be referred for calculating the minimum thickness of the heat exchanger tube in the designing stage. However, the codes and standards related to show the tube plugging criteria may not exist currently. In this paper, a method to establish the tube plugging criteria of BOP heat exchangers, which is based on the USNRC Regulatory Guide 1.121, is introduced and the tube plugging criteria for the TPCCW heat exchanger of Yonggwang NPP No. 1 and 2. This method relies on the similar plugging criteria used in the steam generator

  3. Zero mass field quantization and Kibble's long-range force criterion for the Goldstone theorem

    International Nuclear Information System (INIS)

    Wright, S.H.

    1981-01-01

    The central theme of the dissertation is an investigation of the long-range force criterion used by Kibble in his discussion of the Goldstone Theorem. This investigation is broken up into the following sections: I. Introduction. Spontaneous symmetry breaking, the Goldstone Theorem and the conditions under which it holds are discussed. II. Massless Wave Expansions. In order to make explicit calculations of the operator commutators used in applying Kibble's criterion, it is necessary to work out the operator expansions for a massless field. Unusual results are obtained which include operators corresponding to classical macroscopic field modes. III. The Kibble Criterion for Simple Models Exhibiting Spontaneously Broken Symmetries. The results of the previous section are applied to simple models with spontaneously broken symmetries, namely, the real scalar massless field and the Goldstone model without gauge coupling. IV. The Higgs Mechanism in Classical Field Theory. It is shown that the Higgs Mechanism has a simple interpretation in terms of classical field theory, namely, that it arises from a derivative coupling term between the Goldstone fields and the gauge fields. V. The Higgs Mechanism and Kibble's Criterion. This section draws together the material discussed in sections II to IV. Explicit calculations are made to evaluate Kibble's criterion on a Goldstone-Higgs type of model in the Coulomb gauge. It is found, as expected, that the criterion is not met, but not for reasons relating to the range of the mediating force. By referring to the findings of sections III and IV, it is concluded that the common denominator underlying both the Higgs Mechanism and the failure of Kibble's criterion is a structural aspect of the field equations: derivative coupling between fields

  4. Transformer ratio enhancement experiment

    International Nuclear Information System (INIS)

    Gai, W.; Power, J. G.; Kanareykin, A.; Neasheva, E.; Altmark, A.

    2004-01-01

    Recently, a multibunch scheme for efficient acceleration based on dielectric wakefield accelerator technology was outlined in J.G. Power, W. Gai, A. Kanareykin, X. Sun. PAC 2001 Proceedings, pp. 114-116, 2002. In this paper we present an experimental program for the design, development and demonstration of an Enhanced Transformer Ratio Dielectric Wakefield Accelerator (ETR-DWA). The principal goal is to increase the transformer ratio R, the parameter that characterizes the energy transfer efficiency from the accelerating structure to the accelerated electron beam. We present here an experimental design of a 13.625 GHz dielectric loaded accelerating structure, a laser multisplitter producing a ramped bunch train, and simulations of the bunch train parameters required. Experimental results of the accelerating structure bench testing and ramped pulsed train generation with the laser multisplitter are shown as well. Using beam dynamic simulations, we also obtain the focusing FODO lattice parameters

  5. Intake to Production Ratio

    DEFF Research Database (Denmark)

    Nazaroff, William; Weschler, Charles J.; Little, John C.

    2012-01-01

    BACKGROUND: Limited data are available to assess human exposure to thousands of chemicals currently in commerce. Information that relates human intake of a chemical to its production and use can help inform understanding of mechanisms and pathways that control exposure and support efforts...... to protect public health.OBJECTIVES: We introduce the intake-to-production ratio (IPR) as an economy-wide quantitative indicator of the extent to which chemical production results in human exposure.METHODS: The IPR was evaluated as the ratio of two terms: aggregate rate of chemical uptake in a human......(n-butyl) phthalate, 1,040 ppm for para-dichlorobenzene, 6,800 ppm for di(isobutyl) phthalate, 7,700 ppm for diethyl phthalate, and 8,000-24,000 ppm (range) for triclosan.CONCLUSION: The IPR is well suited as an aggregate metric of exposure intensity for characterizing population-level exposure to synthesized...

  6. Improving data analysis in herpetology: Using Akaike's information criterion (AIC) to assess the strength of biological hypotheses

    Science.gov (United States)

    Mazerolle, M.J.

    2006-01-01

    In ecology, researchers frequently use observational studies to explain a given pattern, such as the number of individuals in a habitat patch, with a large number of explanatory (i.e., independent) variables. To elucidate such relationships, ecologists have long relied on hypothesis testing to include or exclude variables in regression models, although the conclusions often depend on the approach used (e.g., forward, backward, stepwise selection). Though better tools have surfaced in the mid 1970's, they are still underutilized in certain fields, particularly in herpetology. This is the case of the Akaike information criterion (AIC) which is remarkably superior in model selection (i.e., variable selection) than hypothesis-based approaches. It is simple to compute and easy to understand, but more importantly, for a given data set, it provides a measure of the strength of evidence for each model that represents a plausible biological hypothesis relative to the entire set of models considered. Using this approach, one can then compute a weighted average of the estimate and standard error for any given variable of interest across all the models considered. This procedure, termed model-averaging or multimodel inference, yields precise and robust estimates. In this paper, I illustrate the use of the AIC in model selection and inference, as well as the interpretation of results analysed in this framework with two real herpetological data sets. The AIC and measures derived from it is should be routinely adopted by herpetologists. ?? Koninklijke Brill NV 2006.

  7. Using Akaike's information theoretic criterion in mixed-effects modeling of pharmacokinetic data: a simulation study [version 3; referees: 2 approved, 1 approved with reservations

    Directory of Open Access Journals (Sweden)

    Erik Olofsen

    2015-07-01

    Full Text Available Akaike's information theoretic criterion for model discrimination (AIC is often stated to "overfit", i.e., it selects models with a higher dimension than the dimension of the model that generated the data. However, with experimental pharmacokinetic data it may not be possible to identify the correct model, because of the complexity of the processes governing drug disposition. Instead of trying to find the correct model, a more useful objective might be to minimize the prediction error of drug concentrations in subjects with unknown disposition characteristics. In that case, the AIC might be the selection criterion of choice. We performed Monte Carlo simulations using a model of pharmacokinetic data (a power function of time with the property that fits with common multi-exponential models can never be perfect - thus resembling the situation with real data. Prespecified models were fitted to simulated data sets, and AIC and AICc (the criterion with a correction for small sample sizes values were calculated and averaged. The average predictive performances of the models, quantified using simulated validation sets, were compared to the means of the AICs. The data for fits and validation consisted of 11 concentration measurements each obtained in 5 individuals, with three degrees of interindividual variability in the pharmacokinetic volume of distribution. Mean AICc corresponded very well, and better than mean AIC, with mean predictive performance. With increasing interindividual variability, there was a trend towards larger optimal models, but with respect to both lowest AICc and best predictive performance. Furthermore, it was observed that the mean square prediction error itself became less suitable as a validation criterion, and that a predictive performance measure should incorporate interindividual variability. This simulation study showed that, at least in a relatively simple mixed-effects modelling context with a set of prespecified models

  8. Safety and efficacy of Y-90 microsphere treatment in patients with primary and metastatic liver cancer: The tumor selectivity of the treatment as a function of tumor to liver flow ratio

    Directory of Open Access Journals (Sweden)

    Dezarn William A

    2007-03-01

    Full Text Available Abstract Background Treatment records and follow-up data on 40 patients with primary and metastatic liver malignancies who underwent a single whole-liver treatment with Y-90 resin microspheres (SIR-Spheres® Sirtex Medical, Lake Forest, IL were retrospectively reviewed. The objective of the study was to evaluate the anatomic and physiologic determinants of radiation dose distribution, and the dose response of tumor and liver toxicity in patients with liver malignancies who underwent hepatic arterial Y-90 resin microsphere treatment. Methods Liver and tumor volume calculations were performed on pre-treatment CT scans. Fractional tumor and liver flow characteristics and lung shunt fractions were determined using hepatic arterial Tc-99m MAA imaging. Absorbed dose calculations were performed using the MIRD equations. Liver toxicity was assessed clinically and by liver function tests. Tumor response to therapy was assessed by CT and/or tumor markers. Results Of the 40 patients, 5 had hepatocellular cancer (HCC, and 35 had metastatic liver tumors (15 colorectal cancer, 10 neuroendocrine tumors, 4 breast cancer, 2 lung cancer, 1 ovarian cancer, 1 endometrial cancer, and 2 unknown primary adenocarcinoma. All patients were treated in a salvage setting with a 3 to 80 week follow-up (mean: 19 weeks. Tumor volumes ranged from 15.0 to 984.2 cc (mean: 294.9 cc and tumor to normal liver uptake ratios ranged from 2.8 to 15.4 (mean: 5.4. Average administered activity was 1.2 GBq (0.4 to 2.4 GBq. Liver absorbed doses ranged from 0.7 to 99.5 Gy (mean: 17.2 Gy. Tumor absorbed doses ranged from 40.1 to 494.8 Gy (mean: 121.5 Gy. None of the patients had clinical venoocclusive disease or therapy-induced liver failure. Seven patients (17.5 % had transient and 7 patients (17.5 % had persistent LFT abnormalities. There were 27 (67.5% responders (complete response, partial response, and stable disease. Tumor response correlated with higher tumor flow ratio as measured by

  9. Carbon-13 discrimination as a criterion for identifying high water use efficiency wheat cultivars under water deficit conditions

    International Nuclear Information System (INIS)

    Bazza, M.

    1996-01-01

    During four consecutive years, 20 durum wheat (Triticum durum Desf) and bread wheat (Triticum aestrivum L.) cultivars were grown under rain-fed conditions and supplementary irrigation with the objective of assessing the possibility of using 13 C discrimination Δ as a criterion to screen for wheat cultivars that produce high yields and have a better water use efficiency under water deficit conditions. In all four growing season, both treatments were subjected to some water stress which was higher under rain-fed conditions and varied according to the intensity and time of rainfall. During the first growing season, and despite small differences between the two treatments in terms of the amounts of water used, the grain and straw yields as well as Δ were significantly higher in the treatment which received an irrigation at installation than in the one without irrigation. There was substantial genotypic variation in Δ. When both treatments were considered, the total above ground dry matter yield and grain yield were positively correlated with Δ although the correlation coefficient of grain yield versus Δ was not high ( ** ). The data suggest that while a high Δ value may be used as a criterion for selection of cultivars of wheat with potential for high yield and high water use efficiency in wheat under field conditions, caution must be exercised in the selection process as the size of the canopy and the changes in environmental factors mainly soil water content, can result in changes in Δ and the yield of a cultivar. However, Δ of a genotype can also provide valuable information with respect to plant parameters responsible for the control of Δ and this information can be usefully employed in breeding programmes aimed at developing wheat cultivars high in yield and high in water use efficiency, and suitable for cultivation in arid and semi-arid regions of the tropics and sub-tropics. 11 refs, 2 figs, 2 tabs

  10. Carbon-13 discrimination as a criterion for identifying high water use efficiency wheat cultivars under water deficit conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bazza, M [Rabat-Institus, Rabat (Morocco). Inst. Agronomique et Veterinaire Hassan II

    1996-07-01

    During four consecutive years, 20 durum wheat (Triticum durum Desf) and bread wheat (Triticum aestrivum L.) cultivars were grown under rain-fed conditions and supplementary irrigation with the objective of assessing the possibility of using {sup 13}C discrimination {Delta} as a criterion to screen for wheat cultivars that produce high yields and have a better water use efficiency under water deficit conditions. In all four growing season, both treatments were subjected to some water stress which was higher under rain-fed conditions and varied according to the intensity and time of rainfall. During the first growing season, and despite small differences between the two treatments in terms of the amounts of water used, the grain and straw yields as well as {Delta} were significantly higher in the treatment which received an irrigation at installation than in the one without irrigation. There was substantial genotypic variation in {Delta}. When both treatments were considered, the total above ground dry matter yield and grain yield were positively correlated with {Delta} although the correlation coefficient of grain yield versus {Delta} was not high (< 0.45{sup **}). The data suggest that while a high {Delta} value may be used as a criterion for selection of cultivars of wheat with potential for high yield and high water use efficiency in wheat under field conditions, caution must be exercised in the selection process as the size of the canopy and the changes in environmental factors mainly soil water content, can result in changes in {Delta} and the yield of a cultivar. But, {Delta} of a genotype can also provide valuable information with respect to plant parameters responsible for the control of {Delta} and this information can be usefully employed in breeding programmes aimed at developing wheat cultivars high in yield and high in water use efficiency, and suitable for cultivation in arid and semi-arid regions of the tropics and sub-tropics. 11 refs,2figs,2tabs.

  11. VALIDITY OF EXCESS ENTROPY PRODUCTION CRITERION OF THERMODYNAMIC STABILITY FOR NONEQUILIBRIUM STEADY STATES

    Institute of Scientific and Technical Information of China (English)

    吴金平

    1991-01-01

    The relation between the excess entropy production criterion of thermodynamic stabilityfor nonequilibrium states and kinetic linear stability principle is discussed. It is shown thatthe condition required by the excess entropy production criterion generally is sufficient, butnot necessary to judge the system stability. The condition required by the excess entropyproduction criterion is stronger than that of the linear stability principle. Only when theproduct matrix between the linearized matrix of kinetic equations and matrix of quadraticform of second-order excess entropy is symmetric, is the condition required by the excessentropy production criterion that the steady steate is asymptotically stable (δ_xP>0) necessaryand sufficient. The counterexample given by Fox to prove that the excess entropy, (δ~2S)ss,is not a Liapunov function is incorrect. Contradictory to his conclusion, the counterexampleis just a positive one that proves that the excess entropy is a Liapunov function. Moreover,the excess entropy production criterion is not limited by symmetric conditions of the linear-ized matrix of kinetic equations. The excess entropy around nonequilibrium steady states,(δ~2S)ss, is a Liapunov function of thermodynamic system.

  12. Fulfillment of the kinetic Bohm criterion in a quasineutral particle-in-cell model

    International Nuclear Information System (INIS)

    Ahedo, Eduardo; Santos, Robert; Parra, Felix I.

    2010-01-01

    Quasineutral particle-in-cell models of ions must fulfill the kinetic Bohm criterion, in its inequality form, at the domain boundary in order to match correctly with solutions of the Debye sheaths tied to the walls. The simple, fluid form of the Bohm criterion is shown to be a bad approximation of the exact, kinetic form when the ion velocity distribution function has a significant dispersion and involves different charge numbers. The fulfillment of the Bohm criterion is measured by a weighting algorithm at the boundary, but linear weighting algorithms have difficulties to reproduce the nonlinear behavior around the sheath edge. A surface weighting algorithm with an extended temporal weighting is proposed and shown to behave better than the standard volumetric weighting. Still, this must be supplemented by a forcing algorithm of the kinetic Bohm criterion. This postulates a small potential fall in a supplementary, thin, transition layer. The electron-wall interaction is shown to be of little relevance in the fulfillment of the Bohm criterion.

  13. Role of optimization criterion in static asymmetric analysis of lumbar spine load.

    Science.gov (United States)

    Daniel, Matej

    2011-10-01

    A common method for load estimation in biomechanics is the inverse dynamics optimization, where the muscle activation pattern is found by minimizing or maximizing the optimization criterion. It has been shown that various optimization criteria predict remarkably similar muscle activation pattern and intra-articular contact forces during leg motion. The aim of this paper is to study the effect of the choice of optimization criterion on L4/L5 loading during static asymmetric loading. Upright standing with weight in one stretched arm was taken as a representative position. Musculoskeletal model of lumbar spine model was created from CT images of Visible Human Project. Several criteria were tested based on the minimization of muscle forces, muscle stresses, and spinal load. All criteria provide the same level of lumbar spine loading (difference is below 25%), except the criterion of minimum lumbar shear force which predicts unrealistically high spinal load and should not be considered further. Estimated spinal load and predicted muscle force activation pattern are in accordance with the intradiscal pressure measurements and EMG measurements. The L4/L5 spine loads 1312 N, 1674 N, and 1993 N were predicted for mass of weight in hand 2, 5, and 8 kg, respectively using criterion of mininum muscle stress cubed. As the optimization criteria do not considerably affect the spinal load, their choice is not critical in further clinical or ergonomic studies and computationally simpler criterion can be used.

  14. PTSD's risky behavior criterion: Relation with DSM-5 PTSD symptom clusters and psychopathology.

    Science.gov (United States)

    Contractor, Ateka A; Weiss, Nicole H; Dranger, Paula; Ruggero, Camilo; Armour, Cherie

    2017-06-01

    A new symptom criterion of reckless and self-destructive behaviors (E2) was recently added to posttraumatic stress disorder's (PTSD) diagnostic criteria in DSM-5, which is unsurprising given the well-established relation between PTSD and risky behaviors. Researchers have questioned the significance and incremental validity of this symptom criterion within PTSD's symptomatology. Unprecedented to our knowledge, we aim to compare trauma-exposed groups differing on their endorsement status of the risky behavior symptom on several psychopathology constructs (PTSD, depression, distress tolerance, rumination, anger). The sample included 123 trauma-exposed participants seeking mental health treatment (M age=35.70; 68.30% female) who completed self-report questionnaires assessing PTSD symptoms, depression, rumination, distress tolerance, and anger. Results of independent samples t-tests indicated that participants who endorsed the E2 criterion at a clinically significant level reported significantly greater PTSD subscale severity; depression severity; rumination facets of repetitive thoughts, counterfactual thinking, and problem-focused thinking; and anger reactions; and significantly less absorption and regulation (distress tolerance facets) compared to participants who did not endorse the E2 criterion at a clinically significant level. Results indicate the utility of the E2 criterion in identifying trauma-exposed individual with greater posttraumatic distress, and emphasize the importance of targeting such behaviors in treatment. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

  15. An analytic expression for the sheath criterion in magnetized plasmas with multi-charged ion species

    International Nuclear Information System (INIS)

    Hatami, M. M.

    2015-01-01

    The generalized Bohm criterion in magnetized multi-component plasmas consisting of multi-charged positive and negative ion species and electrons is analytically investigated by using the hydrodynamic model. It is assumed that the electrons and negative ion density distributions are the Boltzmann distribution with different temperatures and the positive ions enter into the sheath region obliquely. Our results show that the positive and negative ion temperatures, the orientation of the applied magnetic field and the charge number of positive and negative ions strongly affect the Bohm criterion in these multi-component plasmas. To determine the validity of our derived generalized Bohm criterion, it reduced to some familiar physical condition and it is shown that monotonically reduction of the positive ion density distribution leading to the sheath formation occurs only when entrance velocity of ion into the sheath satisfies the obtained Bohm criterion. Also, as a practical application of the obtained Bohm criterion, effects of the ionic temperature and concentration as well as magnetic field on the behavior of the charged particle density distributions and so the sheath thickness of a magnetized plasma consisting of electrons and singly charged positive and negative ion species are studied numerically

  16. The Reference Return Ratio

    DEFF Research Database (Denmark)

    Nicolaisen, Jeppe; Faber Frandsen, Tove

    2008-01-01

    The paper introduces a new journal impact measure called The Reference Return Ratio (3R). Unlike the traditional Journal Impact Factor (JIF), which is based on calculations of publications and citations, the new measure is based on calculations of bibliographic investments (references) and returns...... (citations). A comparative study of the two measures shows a strong relationship between the 3R and the JIF. Yet, the 3R appears to correct for citation habits, citation dynamics, and composition of document types - problems that typically are raised against the JIF. In addition, contrary to traditional...

  17. Potential support ratios

    DEFF Research Database (Denmark)

    Kjærgaard, Søren; Canudas-Romo, Vladimir

    2017-01-01

    The ‘prospective potential support ratio’ has been proposed by researchers as a measure that accurately quantifies the burden of ageing, by identifying the fraction of a population that has passed a certain measure of longevity, for example, 17 years of life expectancy. Nevertheless......, the prospective potential support ratio usually focuses on the current mortality schedule, or period life expectancy. Instead, in this paper we look at the actual mortality experienced by cohorts in a population, using cohort life tables. We analyse differences between the two perspectives using mortality models...

  18. Introducing optional reserve ratios in Hungary

    OpenAIRE

    Lóránt Varga

    2010-01-01

    As of the reserve maintenance period commencing in November 2010, Hungarian credit institutions will be free to decide whether to apply the previously valid 2% reserve ratio, or to apply a higher mandatory reserve ratio. Credit institutions required to hold reserves may select from reserve ratios of 2, 3, 4 and 5%, and may change their decision on a semi-annual basis. In line with the international best practice, the purpose of the MNB’s reserve requirement system is to support credit institu...

  19. Inverter ratio failure detector

    Science.gov (United States)

    Wagner, A. P.; Ebersole, T. J.; Andrews, R. E. (Inventor)

    1974-01-01

    A failure detector which detects the failure of a dc to ac inverter is disclosed. The inverter under failureless conditions is characterized by a known linear relationship of its input and output voltages and by a known linear relationship of its input and output currents. The detector includes circuitry which is responsive to the detector's input and output voltages and which provides a failure-indicating signal only when the monitored output voltage is less by a selected factor, than the expected output voltage for the monitored input voltage, based on the known voltages' relationship. Similarly, the detector includes circuitry which is responsive to the input and output currents and provides a failure-indicating signal only when the input current exceeds by a selected factor the expected input current for the monitored output current based on the known currents' relationship.

  20. Optimization of Thermal Object Nonlinear Control Systems by Energy Efficiency Criterion.

    Science.gov (United States)

    Velichkin, Vladimir A.; Zavyalov, Vladimir A.

    2018-03-01

    This article presents the results of thermal object functioning control analysis (heat exchanger, dryer, heat treatment chamber, etc.). The results were used to determine a mathematical model of the generalized thermal control object. The appropriate optimality criterion was chosen to make the control more energy-efficient. The mathematical programming task was formulated based on the chosen optimality criterion, control object mathematical model and technological constraints. The “maximum energy efficiency” criterion helped avoid solving a system of nonlinear differential equations and solve the formulated problem of mathematical programming in an analytical way. It should be noted that in the case under review the search for optimal control and optimal trajectory reduces to solving an algebraic system of equations. In addition, it is shown that the optimal trajectory does not depend on the dynamic characteristics of the control object.

  1. Criterion for adoption of urgent decision on population protection measures in case of NPP accident

    International Nuclear Information System (INIS)

    Konstantinov, Yu.O.

    1985-01-01

    The main table of a criterion for making decision about population protection measures in case of NPP accident is reconsidered. In comparison with the previous data the table doesn't contain contact irradiation and food-stuff contamination with 90 Sr and 137 Cs because of their insignificance relatively to external irradiation as a result of inert radioactive gaseous and halogen release and internal irradiation by iodine radioisotopes. Defining more exactly the criterion one should pay more attention to the discussion of numerical values of internal irradiation dose of thyroid gland. The choice of hazard-levels giving the foundation for making decision concerning protection measures should be determined both by biological radiation risk and scale of hazard relative protection urgebcy the degree of accuracy of potential irradiation or contamination evaluation by possibilities of measures carried out in time, difficulties, unfavourable psychologic effect and risk for population health. The criterion should permit flexibility in decision making according to concrete conditions

  2. The precautionary principle as a rational decision criterion; Foere var-prinsippet som rasjonelt beslutningsgrunnlag

    Energy Technology Data Exchange (ETDEWEB)

    Hovi, Jon

    2001-12-01

    The paper asks if the precautionary principle may be seen as a rational decision criterion. Six main questions are discussed. 1. Does the principle basically represent a particular set of political options or is it a genuine decision criterion? 2. If it is the latter, can it be reduced to any of the existing criteria for decision making under uncertainty? 3. In what kinds of situation is the principle applicable? 4. What is the relation between the precautionary principle and other principles for environmental regulation? 5. How plausible is the principle's claim that the burden of proof should be reversed? 6. Do the proponents of environmental regulation carry no burden of proof at all? A main conclusion is that, for now at least, the principle contains too many unclear elements to satisfy the requirements of precision and consistency that should reasonably be satisfied by a rational decision criterion. (author)

  3. Conflicting views on a neutrality criterion for radioactive-waste management

    International Nuclear Information System (INIS)

    Cochran, T.B.; Bodde, D.L.

    1983-01-01

    Two essays are presented by authors who agree that risks imposed on future generations through the management of radioactive waste are acceptable if they meet a criterion of neutrality, but who disagree on the interpretation of the neutrality criterion. The first viewpoint argues that acceptable isolation of high-level radioactive waste is yet to be accomplished and that a fundamental criterion for radioactive waste disposal must include consideration of the intergenerational radiation effects. The second essay promotes balanced resource allocation, technological progress, and adequate problem-solving institutions as the solution to the problem. The debate illustrates the complexities involved in applying philosophical principles to public policy, even when the principles have been agreed upon. 23 references, 1 figure

  4. A risk-based microbiological criterion that uses the relative risk as the critical limit

    DEFF Research Database (Denmark)

    Andersen, Jens Kirk; Nørrung, Birgit; da Costa Alves Machado, Simone

    2015-01-01

    A risk-based microbiological criterion is described, that is based on the relative risk associated to the analytical result of a number of samples taken from a food lot. The acceptable limit is a specific level of risk and not a specific number of microorganisms, as in other microbiological...... criteria. The approach requires the availability of a quantitative microbiological risk assessment model to get risk estimates for food products from sampled food lots. By relating these food lot risk estimates to the mean risk estimate associated to a representative baseline data set, a relative risk...... estimate can be obtained. This relative risk estimate then can be compared with a critical value, defined by the criterion. This microbiological criterion based on a relative risk limit is particularly useful when quantitative enumeration data are available and when the prevalence of the microorganism...

  5. Spatial frequency discrimination: visual long-term memory or criterion setting?

    Science.gov (United States)

    Lages, M; Treisman, M

    1998-02-01

    A long-term sensory memory is believed to account for spatial frequency discrimination when reference and test stimuli are separated by long intervals. We test an alternative proposal: that discrimination is determined by the range of test stimuli, through their entrainment of criterion-setting processes. Experiments 1 and 2 show that the 50% point of the psychometric function is largely determined by the midpoint of the stimulus range, not by the reference stimulus. Experiment 3 shows that discrimination of spatial frequencies is similarly affected by orthogonal contextual stimuli and parallel contextual stimuli and that these effects can be explained by criterion-setting processes. These findings support the hypothesis that discrimination over long intervals is explained by the operation of criterion-setting processes rather than by long-term sensory retention of a neural representation of the stimulus.

  6. Synchronization criterion for Lur'e type complex dynamical networks with time-varying delay

    International Nuclear Information System (INIS)

    Ji, D.H.; Park, Ju H.; Yoo, W.J.; Won, S.C.; Lee, S.M.

    2010-01-01

    In this Letter, the synchronization problem for a class of complex dynamical networks in which every identical node is a Lur'e system with time-varying delay is considered. A delay-dependent synchronization criterion is derived for the synchronization of complex dynamical network that represented by Lur'e system with sector restricted nonlinearities. The derived criterion is a sufficient condition for absolute stability of error dynamics between the each nodes and the isolated node. Using a convex representation of the nonlinearity for error dynamics, the stability condition based on the discretized Lyapunov-Krasovskii functional is obtained via LMI formulation. The proposed delay-dependent synchronization criterion is less conservative than the existing ones. The effectiveness of our work is verified through numerical examples.

  7. Criterion Validity of the “HRQOLISP-E”: A New Context-Specific Screening Tool for Poststroke Depression

    Directory of Open Access Journals (Sweden)

    Akin Ojagbemi

    2017-01-01

    Full Text Available Objectives. The optimal tool for identifying postsroke depression (PSD is yet to be identified. In the present study, we rely on the depression subscale of the Hospital Anxiety and Depression Scale (HADS-D as a meaningful criterion to investigate the psychometric properties of the HRQOLISP-E, a new context-specific screening tool for PSD developed from a large cross-cultural sample. Methods. We assessed baseline data being collected as part of an intervention to improve one-year blood pressure control among recent (≤one month stroke survivors. Depression was measured using the HADS-D and the HRQOLISP-E. We determined sensitivity, specificity, likelihood ratios, and posttest probability. The area under a receiver operator curve (AUC and the most appropriate HRQOLISP-E cut-off were also determined using standard procedures. Results. Using data derived from 387 recent stroke survivors, the HRQOLISP-E showed high agreement with the HADS-D, sensitivity = 73.7%, specificity = 79.3%, and posterior test probability = 88% (95% CI = 84%–91%. The AUC was 0.81 (95% CI = 0.76–0.86. The HRQOLISP-E cut-off, corresponding to HADS-D score ≥ 8, was 20/21 (out of a total score of 30. Conclusions. Within limitations of using the HADS-D as a referent criterion, the present results provide justification for further development of the HRQOLISP-E as the first stroke-specific screening tool for depression.

  8. Development of a brittle fracture acceptance criterion for the International Atomic Energy Agency (IAEA)

    International Nuclear Information System (INIS)

    Sorenson, K.B.; Salzbrenner, R.; Nickell, R.E.

    1992-01-01

    An effort has been undertaken to develop a brittle fracture acceptance criterion for structural components of nuclear material transportation casks. The need for such a criterion was twofold. First, new generation cask designs have proposed the use of ferritic steels and other materials to replace the austenitic stainless steel commonly used for structural components in transport casks. Unlike austenitic stainless steel which fails in a high-energy absorbing, ductile tearing mode, it is possible for these candidate materials to fail via brittle fracture when subjected to certain combinations of elevated loading rates and low temperatures. Second, there is no established brittle fracture criterion accepted by the regulatory community that covers a broad range of structural materials. Although the existing IAEA Safety Series number-sign 37 addressed brittle fracture, its the guidance was dated and pertained only to ferritic steels. Consultant's Services Meetings held under the auspices of the IAEA have resulted in a recommended brittle fracture criterion. The brittle fracture criterion is based on linear elastic fracture mechanics, and is the result of a consensus of experts from six participating IAEA-member countries. The brittle fracture criterion allows three approaches to determine the fracture toughness of the structural material. The three approaches present the opportunity to balance material testing requirements and the conservatism of the material's fracture toughness which must be used to demonstrate resistance to brittle fracture. This work has resulted in a revised Appendix IX to Safety Series number-sign 37 which will be released as an IAEA Technical Document within the coming year

  9. Reliability criteria selection for integrated resource planning

    International Nuclear Information System (INIS)

    Ruiu, D.; Ye, C.; Billinton, R.; Lakhanpal, D.

    1993-01-01

    A study was conducted on the selection of a generating system reliability criterion that ensures a reasonable continuity of supply while minimizing the total costs to utility customers. The study was conducted using the Institute for Electronic and Electrical Engineers (IEEE) reliability test system as the study system. The study inputs and results for conditions and load forecast data, new supply resources data, demand-side management resource data, resource planning criterion, criterion value selection, supply side development, integrated resource development, and best criterion values, are tabulated and discussed. Preliminary conclusions are drawn as follows. In the case of integrated resource planning, the selection of the best value for a given type of reliability criterion can be done using methods similar to those used for supply side planning. The reliability criteria values previously used for supply side planning may not be economically justified when integrated resource planning is used. Utilities may have to revise and adopt new, and perhaps lower supply reliability criteria for integrated resource planning. More complex reliability criteria, such as energy related indices, which take into account the magnitude, frequency and duration of the expected interruptions are better adapted than the simpler capacity-based reliability criteria such as loss of load expectation. 7 refs., 5 figs., 10 tabs

  10. A unique criterion for the classification of the activity of radioactive effluents according to the activity

    International Nuclear Information System (INIS)

    Tasovac, T.; Bojovic, P.; Svabic, A.

    1964-10-01

    The present classification of radioactive effluents into categories, i.e. low, medium, high and very high activity, has not been given a definite criterion. Therefore, some categories include specific activities from 2-6 and more potentials. Therefore, it occurs that the category of medium active effluents in one nuclear center is indicated as low active in the second or as highly active in the third. Therefore, a proposal is given in this paper for a unique criterion for the classification of radioactive effluents according to their activities. This proposal is based on the decontamination factors obtained by various methods and the maximum permissible concentrations of radioactive isotopes in water (author)

  11. Rayleigh Number Criterion for Formation of A-Segregates in Steel Castings and Ingots

    DEFF Research Database (Denmark)

    Rad, M. Torabi; Kotas, Petr; Beckermann, C.

    2013-01-01

    A Rayleigh number-based criterion is developed for predicting the formation of A-segregates in steel castings and ingots. The criterion is calibrated using available experimental data for ingots involving 27 different steel compositions. The critical Rayleigh number above which A-segregates can b......, the primary reason for this over-prediction is persumed to be the presence of a central zone of equiaxed grains in the casting sections. A-segregates do not form when the grain structure is equiaxed. © The Minerals, Metals & Materials Society and ASM International 2013...

  12. Application of controllable unit approach (CUA) to performance-criterion-based nuclear material control and accounting

    International Nuclear Information System (INIS)

    Foster, K.W.; Rogers, D.R.

    1979-01-01

    The Nuclear Regulatory Commission is considering the use of maximum-loss performance criteria as a means of controlling SNM in nuclear plants. The Controllable Unit Approach to material control and accounting (CUA) was developed by Mound to determine the feasibility of controlling a plant to a performance criterion. The concept was tested with the proposed Anderson, SC, mixed-oxide plant, and it was shown that CUA is indeed a feasible method for controlling a complex process to a performance criterion. The application of CUA to an actual low-enrichment plant to assist the NRC in establishing performance criteria for uranium processes is discussed. 5 refs

  13. On the gap-opening criterion of migrating planets in protoplanetary disks

    OpenAIRE

    Malik, Matej; Meru, Farzana; Mayer, Lucio; Meyer, Michael R.

    2015-01-01

    We perform two-dimensional hydrodynamical simulations to quantitatively explore the torque balance criterion for gap-opening (as formulated by Crida et al.) in a variety of disks when considering a migrating planet. We find that even when the criterion is satisfied, there are instances when planets still do not open gaps. We stress that gap-opening is not only dependent on whether a planet has the ability to open a gap, but whether it can do so quickly enough. This can be expressed as an addi...

  14. Valence electron structure of cast iron and graphltization behaviour criterion of elements

    Institute of Scientific and Technical Information of China (English)

    刘志林; 李志林; 孙振国; 杨晓平; 陈敏

    1995-01-01

    The valence electron structure of common alloy elements in phases of cast iron is calculated- The relationship between the electron structure of alloy elements and equilibrium, non-equilibrium solidification and graphitization is revealed by defining the bond energy of the strongest bond in a phase as structure formation factor S. A criterion of graphitization behaviour of elements is advanced with the critical value of the structure formation factor of graphite and the n of the strongest covalent bond in cementite. It is found that this theory conforms to practice very well when the criterion is applied to the common alloy elements.

  15. Generalized statistical criterion for distinguishing random optical groupings from physical multiple systems

    International Nuclear Information System (INIS)

    Anosova, Z.P.

    1988-01-01

    A statistical criterion is proposed for distinguishing between random and physical groupings of stars and galaxies. The criterion is applied to nearby wide multiple stars, triplets of galaxies in the list of Karachentsev, Karachentseva, and Shcherbanovskii, and double galaxies in the list of Dahari, in which the principal components are Seyfert galaxies. Systems that are almost certainly physical, probably physical, probably optical, and almost certainly optical are identified. The limiting difference between the radial velocities of the components of physical multiple galaxies is estimated

  16. Exploring DSM-5 criterion A in Acute Stress Disorder symptoms following natural disaster.

    Science.gov (United States)

    Lavenda, Osnat; Grossman, Ephraim S; Ben-Ezra, Menachem; Hoffman, Yaakov

    2017-10-01

    The present study examines the DSM-5 Acute Stress Disorder (ASD) diagnostic criteria of exposure, in the context of a natural disaster. The study is based on the reports of 1001 Filipinos following the aftermath of super typhoon Haiyan in 2013. Participants reported exposure to injury, psychological distress and ASD symptoms. Findings indicated the association of criterion A with the prevalence of meeting all other ASD diagnostic criteria and high psychological distress. The diagnostic properties of Criterion A are discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. LMFBR safety criteria: cost-benefit considerations under the constraint of an a priori risk criterion

    International Nuclear Information System (INIS)

    Hartung, J.

    1979-01-01

    The role of cost-benefit considerations and a priori risk criteria as determinants of Core Disruptive Accident (CDA)-related safety criteria for large LMFBR's is explored with the aid of quantitative risk and probabilistic analysis methods. A methodology is described which allows a large number of design and siting alternatives to be traded off against each other with the goal of minimizing energy generation costs subject to the constraint of both an a priori risk criterion and a cost-benefit criterion. Application of this methodology to a specific LMFBR design project is described and the results are discussed. 5 refs

  18. Scalar energy fluctuations in Large-Eddy Simulation of turbulent flames: Statistical budgets and mesh quality criterion

    Energy Technology Data Exchange (ETDEWEB)

    Vervisch, Luc; Domingo, Pascale; Lodato, Guido [CORIA - CNRS and INSA de Rouen, Technopole du Madrillet, BP 8, 76801 Saint-Etienne-du-Rouvray (France); Veynante, Denis [EM2C - CNRS and Ecole Centrale Paris, Grande Voie des Vignes, 92295 Chatenay-Malabry (France)

    2010-04-15

    Large-Eddy Simulation (LES) provides space-filtered quantities to compare with measurements, which usually have been obtained using a different filtering operation; hence, numerical and experimental results can be examined side-by-side in a statistical sense only. Instantaneous, space-filtered and statistically time-averaged signals feature different characteristic length-scales, which can be combined in dimensionless ratios. From two canonical manufactured turbulent solutions, a turbulent flame and a passive scalar turbulent mixing layer, the critical values of these ratios under which measured and computed variances (resolved plus sub-grid scale) can be compared without resorting to additional residual terms are first determined. It is shown that actual Direct Numerical Simulation can hardly accommodate a sufficiently large range of length-scales to perform statistical studies of LES filtered reactive scalar-fields energy budget based on sub-grid scale variances; an estimation of the minimum Reynolds number allowing for such DNS studies is given. From these developments, a reliability mesh criterion emerges for scalar LES and scaling for scalar sub-grid scale energy is discussed. (author)

  19. Design of Biomass Combined Heat and Power (CHP Systems based on Economic Risk using Minimax Regret Criterion

    Directory of Open Access Journals (Sweden)

    Ling Wen Choong

    2018-01-01

    Full Text Available It is a great challenge to identify optimum technologies for CHP systems that utilise biomass and convert it into heat and power. In this respect, industry decision makers are lacking in confidence to invest in biomass CHP due to economic risk from varying energy demand. This research work presents a linear programming systematic framework to design biomass CHP system based on potential loss of profit due to varying energy demand. Minimax Regret Criterion (MRC approach was used to assess maximum regret between selections of the given biomass CHP design based on energy demand. Based on this, the model determined an optimal biomass CHP design with minimum regret in economic opportunity. As Feed-in Tariff (FiT rates affects the revenue of the CHP plant, sensitivity analysis was then performed on FiT rates on the selection of biomass CHP design. Besides, design analysis on the trend of the optimum design selected by model was conducted. To demonstrate the proposed framework in this research, a case study was solved using the proposed approach. The case study focused on designing a biomass CHP system for a palm oil mill (POM due to large energy potential of oil palm biomass in Malaysia.

  20. Peak power ratio generator

    Science.gov (United States)

    Moyer, R.D.

    A peak power ratio generator is described for measuring, in combination with a conventional power meter, the peak power level of extremely narrow pulses in the gigahertz radio frequency bands. The present invention in a preferred embodiment utilizes a tunnel diode and a back diode combination in a detector circuit as the only high speed elements. The high speed tunnel diode provides a bistable signal and serves as a memory device of the input pulses for the remaining, slower components. A hybrid digital and analog loop maintains the peak power level of a reference channel at a known amount. Thus, by measuring the average power levels of the reference signal and the source signal, the peak power level of the source signal can be determined.

  1. The adenoid-nasopharynx ratio. Its clinical value in children

    International Nuclear Information System (INIS)

    Zou Mingshun

    1997-01-01

    To evaluate the clinical usefulness of adenoid-nasopharynx ratio (A/N ratio) measured on nasopharyngeal lateral plain film, 106 clinical cases of secretory otitis media were selected to measure the A/N ratio before treatment. For patients with A/N ratio of 0.50-0.70, the symptoms improved distinctly after conservative treatment, but one half of patients with A/N ratio ≥ 0.71 required adenoidectomy. A/N ratio is a practical and convenient method for evaluation of the adenoid. A/N ratio ≥ 0.71 indicates pathological enlarged adenoid

  2. The applicability of fair selection models in the South African context

    Directory of Open Access Journals (Sweden)

    G. K. Huysamen

    1995-06-01

    Full Text Available This article reviews several models that are aimed at achieving fair selection in situations in which underrepresented groups tend to obtain lower scores on selection tests. Whereas predictive bias is a statistical concept that refers to systematic errors in the prediction of individuals' criterion scores, selection fairness pertains to the extent to which selection results meet certain socio-political demands. The regression and equal-risk models adjust for differences in the criterion-on-test regression lines of different groups. The constant ratio, conditional probability and equal probability models manipulate the test cutoff scores of different groups so that certain ratios formed between different selection outcomes (correct acceptances, correct rejections, incorrect acceptances, incorrect rejections are the same for such groups. The decision-theoretic approach requires that utilities be attached to these different outcomes for different groups. These procedures are not only eminently suited to accommodate calls for affirmative action, but they also serve the cause of transparency. Opsomming Hierdie artikel verskaf 'n oorsig van verskeie modelle om billike keuring te verkry in situasies waar onderverteen-woordigende groepe geneig is om swakker op keuringstoetse te vaar. Terwyl voorspellingsydigheid 'n statistiese begrip is wat betrekking het op stelselmatige foute in die voorspelling van individue se kriteriumtellings, het keuringsbillikheid te make met die mate waarin keuringsresultate aan sekere sosiaal-politieke vereistes voldoen. Die regressieen gelyke-risiko-modelle maak aanpassings vir verskille in die kriterium-op-toetsregressielyne van verskillende groepe. Die konstante-verhoudings, voorwaardelike-waarskynlikheids- en gelyke-waarskynlikheidsmodelle manipuleer die toetsafkappunte van verskillende groepe sodat sekere verhoudings wat tussen keuringsresultate (korrekte aanvaardings, verkeerde aanvaardings, korrekte verwerpings

  3. Determination of the ratio between phosphorus and uranium in surface waters selected in the State of Mexico; Determinacion de la relacion entre fosforo y uranio en cuerpos de agua seleccionados en el Estado de Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez R, E

    2001-07-01

    The agricultural regions lately, they have suffered a severe contamination for the big ones quantities of chemical fertilizers and of pesticides applied to improve their production and quality, increasing these in areas with temperatures but you lower that the average. For the importance of the physicochemical processes that they are made in the waters to settle down surface near to agricultural fields, the physicochemical characteristics were analysed of these waters to determine the contributions that they carry out the phosphate fertilizers that are carried by the escorrentia toward the borders and to make a pursuit of their variability during an agricultural cycle, in times of the summertime and of rains, as well as to observe the effect of the depth in these physicochemical properties. Its were sampling three borders and a spring that it served of white, all them located in the suburbs of the Xinantecatl (Nevado de Toluca), municipality of Zinacantepec, State of Mexico, area with the temperatures but drops registered in the region. They were carried out samplings in the first days of the months of April, July and November. The points of those sampled borders were the influent, the effluent and 3 different depths (lm, 3m and 5m). where was not possible sampling all the points, its were sampling only the one influent and the effluent. The selected physicochemical parameters were the temperature, the pH, the conductivity electric and the one oxygenates dissolved This determination in situ you carries out with a team portable of type Check-Mate, of interchangeable electrodes. The certain anions they were phosphates, nitrates, sulfates and bicarbonates; the measurement of the concentration of anions, one carries out for ultraviolet-visible light spectroscopy and titration. The cations analysed they were sodium, potassium, iron, calcium and magnesium. The cations concentration was determined by atomic absorption spectroscopy. The determination of the uranium

  4. Determination of the ratio between phosphorus and uranium in surface waters selected in the State of Mexico; Determinacion de la relacion entre fosforo y uranio en cuerpos de agua seleccionados en el Estado de Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez R, E

    2001-07-01

    The agricultural regions lately, they have suffered a severe contamination for the big ones quantities of chemical fertilizers and of pesticides applied to improve their production and quality, increasing these in areas with temperatures but you lower that the average. For the importance of the physicochemical processes that they are made in the waters to settle down surface near to agricultural fields, the physicochemical characteristics were analysed of these waters to determine the contributions that they carry out the phosphate fertilizers that are carried by the escorrentia toward the borders and to make a pursuit of their variability during an agricultural cycle, in times of the summertime and of rains, as well as to observe the effect of the depth in these physicochemical properties. Its were sampling three borders and a spring that it served of white, all them located in the suburbs of the Xinantecatl (Nevado de Toluca), municipality of Zinacantepec, State of Mexico, area with the temperatures but drops registered in the region. They were carried out samplings in the first days of the months of April, July and November. The points of those sampled borders were the influent, the effluent and 3 different depths (lm, 3m and 5m). where was not possible sampling all the points, its were sampling only the one influent and the effluent. The selected physicochemical parameters were the temperature, the pH, the conductivity electric and the one oxygenates dissolved This determination in situ you carries out with a team portable of type Check-Mate, of interchangeable electrodes. The certain anions they were phosphates, nitrates, sulfates and bicarbonates; the measurement of the concentration of anions, one carries out for ultraviolet-visible light spectroscopy and titration. The cations analysed they were sodium, potassium, iron, calcium and magnesium. The cations concentration was determined by atomic absorption spectroscopy. The determination of the uranium

  5. fracture criterion

    Indian Academy of Sciences (India)

    “we never test the strength of glass: all we test is the weakness of its surface” J. T. ... 300. 400. 500. 600. Temperature, T ( C). Supercooled Liquid. Regime ... H eat F low. (m. W. ) Pd40Ni10Cu30P20. PDF Create! 5 Trial www.nuance.com ...

  6. Envera Variable Compression Ratio Engine

    Energy Technology Data Exchange (ETDEWEB)

    Charles Mendler

    2011-03-15

    the compression ratio can be raised (to as much as 18:1) providing high engine efficiency. It is important to recognize that for a well designed VCR engine cylinder pressure does not need to be higher than found in current production turbocharged engines. As such, there is no need for a stronger crankcase, bearings and other load bearing parts within the VCR engine. The Envera VCR mechanism uses an eccentric carrier approach to adjust engine compression ratio. The crankshaft main bearings are mounted in this eccentric carrier or 'crankshaft cradle' and pivoting the eccentric carrier 30 degrees adjusts compression ratio from 9:1 to 18:1. The eccentric carrier is made up of a casting that provides rigid support for the main bearings, and removable upper bearing caps. Oil feed to the main bearings transits through the bearing cap fastener sockets. The eccentric carrier design was chosen for its low cost and rigid support of the main bearings. A control shaft and connecting links are used to pivot the eccentric carrier. The control shaft mechanism features compression ratio lock-up at minimum and maximum compression ratio settings. The control shaft method of pivoting the eccentric carrier was selected due to its lock-up capability. The control shaft can be rotated by a hydraulic actuator or an electric motor. The engine shown in Figures 3 and 4 has a hydraulic actuator that was developed under the current program. In-line 4-cylinder engines are significantly less expensive than V engines because an entire cylinder head can be eliminated. The cost savings from eliminating cylinders and an entire cylinder head will notably offset the added cost of the VCR and supercharging. Replacing V6 and V8 engines with in-line VCR 4-cylinder engines will provide high fuel economy at low cost. Numerous enabling technologies exist which have the potential to increase engine efficiency. The greatest efficiency gains are realized when the right combination of advanced and new

  7. The Liquidity Coverage Ratio: the need for further complementary ratios?

    OpenAIRE

    Ojo, Marianne

    2013-01-01

    This paper considers components of the Liquidity Coverage Ratio – as well as certain prevailing gaps which may necessitate the introduction of a complementary liquidity ratio. The definitions and objectives accorded to the Liquidity Coverage Ratio (LCR) and Net Stable Funding Ratio (NSFR) highlight the focus which is accorded to time horizons for funding bank operations. A ratio which would focus on the rate of liquidity transformations and which could also serve as a complementary metric gi...

  8. The evolution of sex ratios and sex-determining systems

    NARCIS (Netherlands)

    Uller, Tobias; Pen, Ido; Wapstra, Erik; Beukeboom, Leo W.; Komdeur, Jan

    Sex determination is a fundamental process governed by diverse mechanisms. Sex ratio selection is commonly implicated in the evolution of sex-determining systems, although formal models are rare. Here, we argue that, although sex ratio selection can induce shifts in sex determination, genomic

  9. Optimum ratio of main mechanized operations for direct-flow fertilizers introduction

    Directory of Open Access Journals (Sweden)

    V. P. Uvarov

    2016-01-01

    Full Text Available Use of transport and technological means is carried out according to the direct-flow scheme and includes stage-by-stage performance as the main standard-setting operations (fertilizers transportation, movement and their distribution across a field, and auxiliary (return from a field and loading of fertilizers. The method of comparison of main types of operations at fertilizers application is given. An estimation criterion is a ratio of cargo movements on a road and across a field, proportionality coefficient between movement of freight and a fertilizers distribution area across the field. These indicators depend on transportation distances and doses of fertilizers application, and also on technology factor that is freight moving frequency across the field. The last characteristic is taken as the optimized parameter. An extremum of this indicator was searched due to a classical method. Optimum values of estimated indicators with the accounting of a variation of a ratio of load capacity and operating width of technical means are received. Concrete combinations of transportation distances and doses of fertilizers application are specified. The authors defined conditions of effective use of tractor and perspective automobile transport and technological means. They recommended to use the automeans allowing to change operating width. Realization of the stated methodological approach will make it possible to select an optimum ratio of the mechanized operations at direct-flow fertilizers application, to exclude additional cargo movements across the field, to cut fuel consumption, to increase productivity. Productivity of transport and technological means increases by 2.0; 1.3 and 1.15 times respectively to length of furrow 3; 9 and 27 km at fertilizers application by a dose of 0.06 kg per sq.m.

  10. Corrections for criterion reliability in validity generalization: The consistency of Hermes, the utility of Midas

    Directory of Open Access Journals (Sweden)

    Jesús F. Salgado

    2016-04-01

    Full Text Available There is criticism in the literature about the use of interrater coefficients to correct for criterion reliability in validity generalization (VG studies and disputing whether .52 is an accurate and non-dubious estimate of interrater reliability of overall job performance (OJP ratings. We present a second-order meta-analysis of three independent meta-analytic studies of the interrater reliability of job performance ratings and make a number of comments and reflections on LeBreton et al.s paper. The results of our meta-analysis indicate that the interrater reliability for a single rater is .52 (k = 66, N = 18,582, SD = .105. Our main conclusions are: (a the value of .52 is an accurate estimate of the interrater reliability of overall job performance for a single rater; (b it is not reasonable to conclude that past VG studies that used .52 as the criterion reliability value have a less than secure statistical foundation; (c based on interrater reliability, test-retest reliability, and coefficient alpha, supervisor ratings are a useful and appropriate measure of job performance and can be confidently used as a criterion; (d validity correction for criterion unreliability has been unanimously recommended by "classical" psychometricians and I/O psychologists as the proper way to estimate predictor validity, and is still recommended at present; (e the substantive contribution of VG procedures to inform HRM practices in organizations should not be lost in these technical points of debate.

  11. On the regularity criterion of weak solutions for the 3D MHD equations

    Science.gov (United States)

    Gala, Sadek; Ragusa, Maria Alessandra

    2017-12-01

    The paper deals with the 3D incompressible MHD equations and aims at improving a regularity criterion in terms of the horizontal gradient of velocity and magnetic field. It is proved that the weak solution ( u, b) becomes regular provided that ( \

  12. A new criterion for global robust stability of interval neural networks with discrete time delays

    International Nuclear Information System (INIS)

    Li Chuandong; Chen Jinyu; Huang Tingwen

    2007-01-01

    This paper further studies global robust stability of a class of interval neural networks with discrete time delays. By introducing an equivalent transformation of interval matrices, a new criterion on global robust stability is established. In comparison with the results reported in the literature, the proposed approach leads to results with less restrictive conditions. Numerical examples are also worked through to illustrate our results

  13. Person fit and criterion-related validity: an extension of the Schmitt, Cortina, and Whitney study

    NARCIS (Netherlands)

    Meijer, R.R.

    1997-01-01

    The effect on criterion-related validity of nonfitting response vectors (NRVs) on a predictor test was investigated. Using simulated data, it was shown that there was a substantial decrease in validity when the type of misfit was severe (i.e., guessing the correct answers to all test items), when

  14. Entanglement in SU(2)-invariant quantum systems: The positive partial transpose criterion and others

    International Nuclear Information System (INIS)

    Schliemann, John

    2005-01-01

    We study entanglement in mixed bipartite quantum states which are invariant under simultaneous SU(2) transformations in both subsystems. Previous results on the behavior of such states under partial transposition are substantially extended. The spectrum of the partial transpose of a given SU(2)-invariant density matrix ρ is entirely determined by the diagonal elements of ρ in a basis of tensor-product states of both spins with respect to a common quantization axis. We construct a set of operators which act as entanglement witnesses on SU(2)-invariant states. A sufficient criterion for ρ having a negative partial transpose is derived in terms of a simple spin correlator. The same condition is a necessary criterion for the partial transpose to have the maximum number of negative eigenvalues. Moreover, we derive a series of sum rules which uniquely determine the eigenvalues of the partial transpose in terms of a system of linear equations. Finally we compare our findings with other entanglement criteria including the reduction criterion, the majorization criterion, and the recently proposed local uncertainty relations

  15. When non-Gaussian states are Gaussian: Generalization of nonseparability criterion for continuous variables

    International Nuclear Information System (INIS)

    McHugh, Derek; Buzek, Vladimir; Ziman, Mario

    2006-01-01

    We present a class of non-Gaussian two-mode continuous-variable states for which the separability criterion for Gaussian states can be employed to detect whether they are separable or not. These states reduce to the two-mode Gaussian states as a special case

  16. An adaptive pruning algorithm for the discrete L-curve criterion

    DEFF Research Database (Denmark)

    Hansen, Per Christian; Jensen, Toke Koldborg; Rodriguez, Giuseppe

    2007-01-01

    We describe a robust and adaptive implementation of the L-curve criterion, i.e., for locating the corner of a discrete L-curve consisting of a log-log plot of corresponding residual and solution norms of regularized solutions from a method with a discrete regularization parameter (such as truncated...

  17. LSSVM-Based Rock Failure Criterion and Its Application in Numerical Simulation

    Directory of Open Access Journals (Sweden)

    Changxing Zhu

    2015-01-01

    Full Text Available A rock failure criterion is very important for the prediction of the failure of rocks or rock masses in rock mechanics and engineering. Least squares support vector machines (LSSVM are a powerful tool for addressing complex nonlinear problems. This paper describes a LSSVM-based rock failure criterion for analyzing the deformation of a circular tunnel under different in situ stresses without assuming a function form. First, LSSVM was used to represent the nonlinear relationship between the mechanical properties of rock and the failure behavior of the rock in order to construct a rock failure criterion based on experimental data. Then, this was used in a hypothetical numerical analysis of a circular tunnel to analyze the mechanical behavior of the rock mass surrounding the tunnel. The Mohr-Coulomb and Hoek-Brown failure criteria were also used to analyze the same case, and the results were compared; these clearly indicate that LSSVM can be used to establish a rock failure criterion and to predict the failure of a rock mass during excavation of a circular tunnel.

  18. Reviewing Employee Turnover: Focusing on Proximal Withdrawal States and an Expanded Criterion

    Science.gov (United States)

    Hom, Peter W.; Mitchell, Terence R.; Lee, Thomas W.; Griffeth, Rodger W.

    2012-01-01

    We reconceptualize employee turnover to promote researchers' understanding and prediction of why employees quit or stay in employing institutions. A literature review identifies shortcomings with prevailing turnover dimensions. In response, we expand the conceptual domain of the turnover criterion to include multiple types of turnover (notably,…

  19. Reliability and criterion validity of an observation protocol for working technique assessments in cash register work.

    Science.gov (United States)

    Palm, Peter; Josephson, Malin; Mathiassen, Svend Erik; Kjellberg, Katarina

    2016-06-01

    We evaluated the intra- and inter-observer reliability and criterion validity of an observation protocol, developed in an iterative process involving practicing ergonomists, for assessment of working technique during cash register work for the purpose of preventing upper extremity symptoms. Two ergonomists independently assessed 17 15-min videos of cash register work on two occasions each, as a basis for examining reliability. Criterion validity was assessed by comparing these assessments with meticulous video-based analyses by researchers. Intra-observer reliability was acceptable (i.e. proportional agreement >0.7 and kappa >0.4) for 10/10 questions. Inter-observer reliability was acceptable for only 3/10 questions. An acceptable inter-observer reliability combined with an acceptable criterion validity was obtained only for one working technique aspect, 'Quality of movements'. Thus, major elements of the cashiers' working technique could not be assessed with an acceptable accuracy from short periods of observations by one observer, such as often desired by practitioners. Practitioner Summary: We examined an observation protocol for assessing working technique in cash register work. It was feasible in use, but inter-observer reliability and criterion validity were generally not acceptable when working technique aspects were assessed from short periods of work. We recommend the protocol to be used for educational purposes only.

  20. A practical criterion of irreducibility of multi-loop Feynman integrals

    International Nuclear Information System (INIS)

    Baikov, P.A.

    2006-01-01

    A practical criterion for the irreducibility (with respect to integration by part identities) of a particular Feynman integral to a given set of integrals is presented. The irreducibility is shown to be related to the existence of stable (with zero gradient) points of a specially constructed polynomial

  1. Development and Criterion Validity of Differentiated and Elevated Vocational Interests in Adolescence

    Science.gov (United States)

    Hirschi, Andreas

    2009-01-01

    Interest differentiation and elevation are supposed to provide important information about a person's state of interest development, yet little is known about their development and criterion validity. The present study explored these constructs among a group of Swiss adolescents. Study 1 applied a cross-sectional design with 210 students in 11th…

  2. A simple criterion to predict the glass forming ability of metallic alloys

    International Nuclear Information System (INIS)

    Falcao de Oliveira, Marcelo

    2012-01-01

    A new and simple criterion with which to quantitatively predict the glass forming ability (GFA) of metallic alloys is proposed. It was found that the critical cooling rate for glass formation (R C ) correlates well with a proper combination of two factors, the minimum topological instability (λ min ) and the Δh parameter, which depends on the average work function difference (Δφ) and the average electron density difference (Δn ws 1/3 ) among the constituent elements of the alloy. A correlation coefficient (R 2 ) of 0.76 was found between R c and the new criterion for 68 alloys in 30 different metallic systems. The new criterion and the Uhlmann's approach were used to estimate the critical amorphous thickness (Z C ) of alloys in the Cu-Zr system. The new criterion underestimated R C in the Cu-Zr system, producing predicted Z C values larger than those observed experimentally. However, when considering a scale factor, a remarkable similarity was observed between the predicted and the experimental behavior of the GFA in the binary Cu-Zr. When using the same scale factor and performing the calculation for the ternary Zr-Cu-Al, good agreement was found between the predicted and the actual best GFA region, as well as between the expected and the observed critical amorphous thickness.

  3. 46 CFR 167.01-8 - Inspection of school ships using gross tonnage criterion.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection of school ships using gross tonnage criterion... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS General Provisions § 167.01-8 Inspection of school ships using gross... school ships by relative sizes in gross tonnages. When it is determined in accordance with § 70.05-20 of...

  4. Changing the criterion for memory conformity in free recall and recognition.

    Science.gov (United States)

    Wright, Daniel B; Gabbert, Fiona; Memon, Amina; London, Kamala

    2008-02-01

    People's responses during memory studies are affected by what other people say. This memory conformity effect has been shown in both free recall and recognition. Here we examine whether accurate, inaccurate, and suggested answers are affected similarly when the response criterion is varied. In the first study, participants saw four pictures of detailed scenes and then discussed the content of these scenes with another participant who saw the same scenes, but with a couple of details changed. Participants were either told to recall everything they could and not to worry about making mistakes (lenient), or only to recall items if they were sure that they were accurate (strict). The strict instructions reduced the amount of inaccurate information reported that the other person suggested, but also reduced the number of accurate details recalled. In the second study, participants were shown a large set of faces and then their memory recognition was tested with a confederate on these and fillers. Here also, the criterion manipulation shifted both accurate and inaccurate responses, and those suggested by the confederate. The results are largely consistent with a shift in response criterion affecting accurate, inaccurate, and suggested information. In addition we varied the level of secrecy in the participants' responses. The effects of secrecy were complex and depended on the level of response criterion. Implications for interviewing eyewitnesses and line-ups are discussed.

  5. Tightening the Dutch coffee shop policy: Evaluation of the private club and the residence criterion

    NARCIS (Netherlands)

    van Ooyen-Houben, M.M.J.; Bieleman, B.; Korf, D.J.

    2016-01-01

    Background The Dutch coffee shop policy was tightened in 2012. Two additional criteria that coffee shops must adhere to in order for them to be tolerated came into force: the private club and the residence criterion. Coffee shops were only permitted to give access to members and only residents of

  6. The implication of using ''consequences'' as a criterion for reactor design

    International Nuclear Information System (INIS)

    Cave, L.; Holmes, P.

    1978-01-01

    The influences which may necessitate closer consideration of reactor accident consequences, rather than reactor risk, as a criterion for design are examined briefly. Possible methods for reducing consequences are described and the advantages of inherent features for this purpose are discussed. The cost effectiveness of two possible methods of reducing consequences and risks is estimated. (author)

  7. The incorporation of displacement-controlled loadings within the net-section stress failure criterion

    International Nuclear Information System (INIS)

    Smith, E.

    1985-01-01

    A net-section stress failure criterion can be used to evaluate the critical flaw size for a material having a high fracture resistance. A simple analysis shows that the stress arising from displacement-controlled loadings should be taken into account fully if the applied tearing modulus exceeds a critical value. (author)

  8. Using Item Data for Evaluating Criterion Reference Measures with an Empirical Investigation of Index Consistency.

    Science.gov (United States)

    Meredith, Keith E.; Sabers, Darrell L.

    Data required for evaluating a Criterion Referenced Measurement (CRM) is described with a matrix. The information within the matrix consists of the "pass-fail" decisions of two CRMs. By differentially defining these two CRMs, different concepts of reliability and validity can be examined. Indices suggested for analyzing the matrix are listed with…

  9. A relaxed criterion for contraction theory: application to an underwater vehicle observer

    DEFF Research Database (Denmark)

    Jouffroy, Jerome

    the Jacobian is not uniformly negative definite but fulfils some weaker conditions. Intended as an illustrative example, a nonlinear underwater vehicle observer, which Jacobian is not uniformly negative definite, is presented and proven to be exponentially convergent using the new criterion....

  10. OPTIMIZATION OF THE CRITERION FOR ESTIMATING THE TECHNOLOGY EFFICIENCY OF PACKING-CASE-PIECE LOADS DELIVERY

    OpenAIRE

    O. Severyn; O. Shulika

    2017-01-01

    The results of optimization of gravimetric coefficients for indexes included in the integral criterion of estimation of the efficiency of transport-technological charts of cargo delivery are resulted. The values of gravimetric coefficients are determined on the basis of two methods of experimental researches: questioning of respondents among the specialists of motor transport production and imitation design.

  11. Ginsburg criterion for an equilibrium superradiant model in the dynamic approach

    International Nuclear Information System (INIS)

    Trache, M.

    1991-10-01

    Some critical properties of an equilibrium superradiant model are discussed, taking into account the quantum fluctuations of the field variables. The critical region is calculated using the Ginsburg criterion, underlining the role of the atomic concentration as a control parameter of the phase transition. (author). 16 refs, 1 fig

  12. Validation of a Criterion Referenced Test for Young Handicapped Children: PIPER.

    Science.gov (United States)

    Strum, Irene; Shapiro, Madelaine

    The purpose of this study was to validate the Prescriptive Instructional Program for Educational Readiness (PIPER) for utilization as a criterion referenced test (CRT) among learning disabled children. The program consisted of behavioral objectives and diagnostic and/or mastery tasks and activities for each objective in the area of gross motor…

  13. Simpler criterion on W state for perfect quantumstate splitting and quantum teleportation

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    A simpler criterion is presented to judge whether a W state can be taken as quantum channel forperfectly splitting or teleporting an arbitrary single-qubit state. If the W state is usable,the detailed manipulations in the two quantum information processes are amply shown. Moreover,some relevant discussions are made.

  14. Higher order criterion for the nonexistence of formal first integral for nonlinear systems

    Directory of Open Access Journals (Sweden)

    Zhiguo Xu

    2017-11-01

    Full Text Available The main purpose of this article is to find a criterion for the nonexistence of formal first integrals for nonlinear systems under general resonance. An algorithm illustrates an application to a class of generalized Lokta-Volterra systems. Our result generalize the classical Poincare's nonintegrability theorem and the existing results in the literature.

  15. Responder Status Criterion for Stepped Care Trauma-Focused Cognitive Behavioral Therapy for Young Children

    Science.gov (United States)

    Salloum, Alison; Scheeringa, Michael S.; Cohen, Judith A.; Storch, Eric A.

    2015-01-01

    Background: In order to develop Stepped Care trauma-focused cognitive behavioral therapy (TF-CBT), a definition of early response/non-response is needed to guide decisions about the need for subsequent treatment. Objective: The purpose of this article is to (1) establish criterion for defining an early indicator of response/non-response to the…

  16. easyCBM® Reading Criterion Related Validity Evidence: Grades K-1. Technical Report #1309

    Science.gov (United States)

    Lai, Cheng-Fei; Alonzo, Julie; Tindal, Gerald

    2013-01-01

    In this technical report, we present the results of a study to gather criterion-related evidence for Grade K-1 easyCBM® reading measures. We used correlations to examine the relation between the easyCBM® measures and other published measures with known reliability and validity evidence, including the Dynamic Indicators of Basic Early Literacy…

  17. easyCBM® Reading Criterion Related Validity Evidence: Grades 2-5. Technical Report #1310

    Science.gov (United States)

    Lai, Cheng-Fei; Alonzo, Julie; Tindal, Gerald

    2013-01-01

    In this technical report, we present the results of a study to gather criterion-related evidence for Grade 2-5 easyCBM® reading measures. We used correlations to examine the relation between the easyCBM® measures and other published measures with known reliability and validity evidence, including the Gates-MacGinitie Reading Tests and the Dynamic…

  18. Criterion validity of the Physical Activity Scale (PAS2) in Danish adults

    DEFF Research Database (Denmark)

    Lunde Pedersen, Eva Sophie; Mortensen, L H; Brage, S

    2017-01-01

    BACKGROUND: The Physical Activity Scale (PAS2) was developed to measure physical activity (PA) during work, transportation and leisure time, in the Danish adult population. The objective of this study was to assess the criterion validity of PAS2 against a combined accelerometer and heart rate mon...

  19. Localized stability criterion for kink modes in systems with small shear

    International Nuclear Information System (INIS)

    Hastie, R.J.; Johnson, J.L.

    1986-02-01

    A localized magnetohydrodynamic stability criterion for ideal kink instabilities is determined for systems where the safety factor has a local minimum on a rational surface with no pressure gradient. These modes are stable in the cylindrical limit, but toroidal effects can make them unstable. They could provide a partial explanation for the rapid current penetration observed in tokamaks. 7 refs

  20. Is age structure a relevant criterion for the health of fish stocks?

    NARCIS (Netherlands)

    Brunel, T.P.A.; Piet, G.J.

    2013-01-01

    The age and size structure of exploited fish stocks is one of the criteria for Good Environmental Status of commercial fish. However, two underlying assumptions to this criterion remain to be tested: first, that a well-balanced age structure is indeed indicative of a “healthier” stock, and second,