Regulatory supervision of safety indicators; experience with radiation safety indicators in Dukovany nuclear power plant performance

International Nuclear Information System (INIS)

Urbancik, L.; Kulich, V.

2004-01-01

The State Office for Nuclear Safety uses three sets of indicators describing the following aspects of a favourable nuclear power plant operation: smooth operation in normal circumstances, low risk to the population, and operation with a positive safety attitude. These are three safety-related areas for assessment. Each area has its own set of indicators. Overall operational safety performance indicators were identified for each attribute. From this point, a level of strategic indicators was developed, and finally, a set of specific indicators was set up. While neither the overall indicators nor the strategic indicators are directly measurable, the specific indicators are directly measurable and are targeted during inspection. (author)

Performance indicators at Embalse NPP: PSA and safety system indicators based on PSA models

International Nuclear Information System (INIS)

Fornero, D.A.

2001-01-01

Several indicators have been implemented at Embalse NPP. The objective was selecting some representative parameters to evaluate the performance of both the plant and the personnel activities, important for safety. A first set of indicators was defined in accordance with plant technical staff criteria. A complementary set of them was addressed later based on WANO guidance. This report presents the set of indicators used at Embalse NPP, centering the description to related to safety systems performance indicators (SSPI). Some considerations are done about the calculation methods, the need for aligning and updating their values following Embalse Probabilistic Safety Assessment (PSA) development, and some pros and cons of using the PSA model for getting systems indicators. Owing to the fact that PSA ownership by utilities is also a subject of the meeting, some characteristics of the organization of the PSA Project are described at the beginning of the report. At Embalse NPP a Level 1 PSA has been developed under the responsibility of its own plant and with an important contribution from the IAEA. PSA was developed at the site, conducting this to a study strongly interactive with the station staff. (author)

Validation of risk-based performance indicators: Safety system function trends

International Nuclear Information System (INIS)

Boccio, J.L.; Vesely, W.E.; Azarm, M.A.; Carbonaro, J.F.; Usher, J.L.; Oden, N.

1989-10-01

This report describes and applies a process for validating a model for a risk-based performance indicator. The purpose of the risk-based indicator evaluated, Safety System Function Trend (SSFT), is to monitor the unavailability of selected safety systems. Interim validation of this indicator is based on three aspects: a theoretical basis, an empirical basis relying on statistical correlations, and case studies employing 25 plant years of historical data collected from five plants for a number of safety systems. Results using the SSFT model are encouraging. Application of the model through case studies dealing with the performance of important safety systems shows that statistically significant trends in, and levels of, system performance can be discerned which thereby can provide leading indications of degrading and/or improving performances. Methods for developing system performance tolerance bounds are discussed and applied to aid in the interpretation of the trends in this risk-based indicator. Some additional characteristics of the SSFT indicator, learned through the data-collection efforts and subsequent data analyses performed, are also discussed. The usefulness and practicality of other data sources for validation purposes are explored. Further validation of this indicator is noted. Also, additional research is underway in developing a more detailed estimator of system unavailability. 9 refs., 18 figs., 5 tabs

Identifying the most significant indicators of the total road safety performance index.

Science.gov (United States)

Tešić, Milan; Hermans, Elke; Lipovac, Krsto; Pešić, Dalibor

2018-04-01

The review of the national and international literature dealing with the assessment of the road safety level has shown great efforts of the authors who tried to define the methodology for calculating the composite road safety index on a territory (region, state, etc.). The procedure for obtaining a road safety composite index of an area has been largely harmonized. The question that has not been fully resolved yet concerns the selection of indicators. There is a wide range of road safety indicators used to show a road safety situation on a territory. Road safety performance index (RSPI) obtained on the basis of a larger number of safety performance indicators (SPIs) enable decision makers to more precisely define the earlier goal- oriented actions. However, recording a broader comprehensive set of SPIs helps identify the strengths and weaknesses of a country's road safety system. Providing high quality national and international databases that would include comparable SPIs seems to be difficult since a larger number of countries dispose of a small number of identical indicators available for use. Therefore, there is a need for calculating a road safety performance index with a limited number of indicators (RSPI ln n ) which will provide a comparison of a sufficient quality, of as many countries as possible. The application of the Data Envelopment Analysis (DEA) method and correlative analysis has helped to check if the RSPI ln n is likely to be of sufficient quality. A strong correlation between the RSPI ln n and the RSPI has been identified using the proposed methodology. Based on this, the most contributing indicators and methodologies for gradual monitoring of SPIs, have been defined for each country analyzed. The indicator monitoring phases in the analyzed countries have been defined in the following way: Phase 1- the indicators relating to alcohol, speed and protective systems; Phase 2- the indicators relating to roads and Phase 3- the indicators relating to

Empirical analysis of selected nuclear power plant maintenance factors and plant safety

International Nuclear Information System (INIS)

Olson, J.; Osborn, R.N.; Thurber, J.A.; Sommers, P.E.; Jackson, D.H.

1985-07-01

This report contains a statistical analysis of the relationship between selected aspects of nuclear power plant maintenance programs and safety related performance. The report identifies a large number of maintenance resources which can be expected to influence maintenance performance and subsequent plant safety performance. The resources for which data were readily available were related statistically to two sets of performance indicators: maintenance intermediate safety indicators and final safety performance indicators. The results show that the administrative structure of the plant maintenance program is a significant predictor of performance on both sets of indicators

Operational safety system performance alternative to the WANO's indicator

International Nuclear Information System (INIS)

Lyra, Moacir

2002-01-01

One of the operational safety performance indicators recommended by the World Association of Nuclear Operators (WANO) and adopted by Electronuclear is the reliability of the safety systems. The parameter selected to represent this indicator is the average unavailability of the trains of the concerned system. This parameter would be universally representative of the reliability for comparison purpose only if all nuclear power plants were designed within the same redundancy criteria. Considering the diversity of design criteria of the power plants in operation and based on a probabilistic approach, this paper proposes new performance indicators which are comparable regardless the redundancy criteria of the system. A case example applied to a system of the Angra 2 nuclear power plant shows that, even though with the plant in the infancy phase, the performance of the system in the period is very good. (author)

New safety performance indicators for safety assessment of radioactive waste disposal facilities. Cuban experience

International Nuclear Information System (INIS)

Peralta Vital, J.L.; Castillo, R.G.; Olivera, J.

2002-01-01

The paper shows the Cuban experience on implementing geological disposal of radioactive waste and the necessity for identifying new safety performance indicators for the safety assessment (SA) of radioactive waste disposal facilities. The selected indicator was the concentration of natural radioactive elements (U, Ra, Th, K) in the Cuban geologic environment. We have carried out a group of investigations, which have allowed characterising the concentration for the whole Country, creating a wide database where this indicator is associated with the lithology. The main lithologies in Cuba are: the sedimentary rocks (70 percent of national occurrence), which are present in the three regions (limestone and lutite), and finally the igneous and metamorphic rocks. The results show the concentrations ranges of the natural radionuclides associated fundamentally to the variation in the lithology and geographical area of the Country. In Cuba, the higher concentration (ppm) of Uranium and Radium are referenced to the Central region associated to Skarn, while for Thorium (ppm) and Potassium (%), in the East region the concentration peaks in Tuffs have been found. The concentrations ranges obtained are preliminary, they characterise the behaviour of this parameter for the Cuban geology, but they do not represent limits for safety assessment purposes yet. Also other factors should be taken into account as the assessment context, time scales and others assumptions before establishing the final concentration limits for the natural radionuclides as a radiological and nuclear safety performance indicator complementary to dose and risk for safety assessment for radiological and nuclear facilities. (author)

Development of safety performance indicators of regulatory interest (SAFPER) in Pakistan

International Nuclear Information System (INIS)

Khatoon, Abida

2002-01-01

Safety performance indicators provide a very useful tool for monitoring operational safety of a nuclear power plant. Utilities in many countries have developed plant specific indicators for the assessment of their performance and safety. Regulators can make use of some of these indicators for their regulatory assessment. In addition to these regulatory bodies in some countries have also developed programs for the formulation of safety performance indicators which are used in monitoring operational safety and regulatory decision making. Realizing its usefulness Directorate of Nuclear Safety and Radiation Protection (DNSRP-the regulatory body in Pakistan) has also initiated a country specific program for the development of Safety Performance Indicators (SAFPER) based on data provided by the utility and that collected during the course of regulatory inspections. Selected areas of NPP operation to be monitored are: - Significant events; - Safety systems performance; - Barriers integrity; - Environment protection; - Workers radiation safety; and - Emergency Preparedness. One of the objectives of this program is also to monitor the effectiveness of DNSRP regulatory activities. IAEA framework is taken as one of the bases for our program. Safety performance will be assessed on the basis of Performance Indicators and inspection findings. DNSRP program as shown in Appendix includes the indicators in use and under development. It is felt that the term Safety Performance Indicators may be termed as 'SAFPER Indicators' to be used by the Regulators, as it is clear from this presentation that utility safety performance indicators together with the regulatory effectiveness indicators constitute the measure for the adequate safety to the public and the environment. Additional research is still necessary for: - indicator definition for the proposed and under developed indicators; - data collection systems; - thresholds; - trend analysis; - goal setting (benefit from the trend can be

Safety culture management and quantitative indicator evaluation

International Nuclear Information System (INIS)

Mandula, J.

2002-01-01

This report discuses a relationship between safety culture and evaluation of quantitative indicators. It shows how a systematic use of generally shared operational safety indicators may contribute to formation and reinforcement of safety culture characteristics in routine plant operation. The report also briefly describes the system of operational safety indicators used at the Dukovany plant. It is a PC database application enabling an effective work with the indicators and providing all users with an efficient tool for making synoptic overviews of indicator values in their links and hierarchical structure. Using color coding, the system allows quick indicator evaluation against predefined limits considering indicator value trends. The system, which has resulted from several-year development, was completely established at the plant during the years 2001 and 2002. (author)

A study of leading indicators for occupational health and safety management systems in healthcare.

Science.gov (United States)

Almost, Joan M; VanDenKerkhof, Elizabeth G; Strahlendorf, Peter; Caicco Tett, Louise; Noonan, Joanna; Hayes, Thomas; Van Hulle, Henrietta; Adam, Ryan; Holden, Jeremy; Kent-Hillis, Tracy; McDonald, Mike; Paré, Geneviève C; Lachhar, Karanjit; Silva E Silva, Vanessa

2018-04-23

In Ontario, Canada, approximately $2.5 billion is spent yearly on occupational injuries in the healthcare sector. The healthcare sector has been ranked second highest for lost-time injury rates among 16 Ontario sectors since 2009 with female healthcare workers ranked the highest among all occupations for lost-time claims. There is a great deal of focus in Ontario's occupational health and safety system on compliance and fines, however despite this increased focus, the injury statistics are not significantly improving. One of the keys to changing this trend is the development of a culture of healthy and safe workplaces including the effective utilization of leading indicators within Occupational Health and Safety Management Systems (OHSMSs). In contrast to lagging indicators, which focus on outcomes retrospectively, a leading indicator is associated with proactive activities and consists of selected OHSMSs program elements. Using leading indicators to measure health and safety has been common practice in high-risk industries; however, this shift has not occurred in healthcare. The aim of this project is to conduct a longitudinal study implementing six elements of the Ontario Safety Association for Community and Healthcare (OSACH) system identified as leading indicators and evaluating the effectiveness of this intervention on improving selected health and safety workplace indicators. A quasi-experimental longitudinal research design will be used within two Ontario acute care hospitals. The first phase of the study will focus on assessing current OHSMSs using the leading indicators, determining potential facilitators and barriers to changing current OHSMSs, and identifying the leading indicators that could be added or changed to the existing OHSMS in place. Phase I will conclude with the development of an intervention designed to support optimizing current OHSMSs in participating hospitals based on identified gaps. Phase II will pilot test and evaluate the tailored

Safety indicators for the peat industry

Energy Technology Data Exchange (ETDEWEB)

Berezhnoy, S A; Sedov, Yu I; Yenoshevskiy, B A

1981-01-01

Members of the inter-institutional department of 'Labor Protection' of the KPI, in cooperation with members of the peat industry, have developed safety indicators for the peat industry in accordance with the requirements of GOST 12.4.026-76 SSBT, and established the range and order for their use. The safety indicators for the peat industry are divided into four groups (prohibiting, warning, regulating, and indicating), depending on the function.

Development of safety performance indicators in Japan

International Nuclear Information System (INIS)

Ohashi, H.; Tamao, S.; Tanaka, J.; Sawayama, T.

2001-01-01

For the purpose of safety regulations of operating nuclear power stations in Japan, the regulatory authorities utilize two types of regulations. One is the direct regulation, such as periodical inspection to inspect the function and performance of equipment important to safety, and the other is the audit type regulation such as preservation inspection to audit the compliance with the safety preservation rules. As performance indicators are expected to be an effective tool to evaluate the activities by audit type regulations, NUPEC is studying a comprehensive set of operational performance indicators to meet the effective evaluation method for the safety preservation activities in the audit type regulations under the frame of current safety regulation system. The study includes the establishment of comprehensive operational performance indicators applicable in Japan, the effective application of performance indicators to the current Japanese regulation, the clarification of the applicable scope of utilization, the possibility of applying the performance indicators. This report describes the present status of our performance indicator studies. After the completion of these studies the regulatory authorities will evaluate if and how the new set of comprehensive performance indicators could be introduced to Japanese regulatory scheme. (author)

geo-scientific indicators for safety

International Nuclear Information System (INIS)

Andersson, J.; Bruno, G.; Deguchi, A.; Fein, E.; Larue, P.J.; Lei, S.; Leung, H.; Norris, S.; Violette, S.; Wollrath, J.

2007-01-01

Working Group A was continuation of Working Group B of AMIGO-1, but participants explored more deeply the issues surrounding geo-scientific indicators for safety. The following outcomes were expected. - List different geo-scientific arguments or indicators for safety (with motivation) for various host rocks and sites. Consider dividing the arguments into those that support isolation or retention and discuss their applicability for different time frames. - What actual measurable field evidence supports these arguments/indicators? - What kind of field evidence would go counter to these safety arguments? - What key messages are the most promising in terms of scientific credibility to contribute to the safety case? Possibly examine the same message but in terms of potential ease of communication. The session started with two introductory presentations: - Following the presentations, in discussion the Working Group listed: - Safety Functions where geo-scientific support is needed; - Commonly used chains of argument for supporting these safety functions; - Whether the applicability of the arguments are host rock or site specific and how they apply for different time frames; - Field evidence or other issues that would go counter to the safety arguments; - Key messages most promising in terms of scientific credibility to contribute to the safety case. Overall it was concluded by the Working Group that: - The most important argument is to present a clear understanding of past geological evolution at the particular site, consistent with the global understanding of geological evolution. Efforts should be made to achieve a broad consensus on this from many independent experts. - The supporting arguments are seldom based on a single piece of evidence. It is the chain of arguments rather than individual arguments that is important. - We are primarily interested in 'reasonable' predictability of the geological system. We recognize that most geological systems evolve with time

Development and use of safety indicators at STUK

International Nuclear Information System (INIS)

Tiipana, P.

2001-01-01

This paper gives an outline of the development and use of STUK's indicator system at the department of Nuclear Reactor Regulation (YTO) in the Radiation and Nuclear Safety Authority, STUK. Indicators used at YTO are measures related to the safety of nuclear installations and regulatory activities. Indicators are numbers, ratios, percentages and amounts of interested matters that are for suitable for regulatory purposes, that is assessment and trending of the safety of nuclear installations and regulatory activities. STUK's indicator system is divided into two main areas: safety of nuclear facilities and regulatory activities. Safety of nuclear facilities is divided into 3 areas based on the concept of defence in de safety and quality culture, operational events and physical barriers. Regulatory activities are divided into 3 areas: working processes, resource management and regeneration and ability to work. These areas are measured using several indicators. At the moment some of indicators are included in YTO's management system to measure whether or not internally set goals are achieved. (author)

Safety performance indicators for the road network.

NARCIS (Netherlands)

Weijermars, W. Gitelman, V. Papadimitriou, E. Lima De & Azevedo, C.

2010-01-01

Within the 6th FP European project SafetyNet, a team has worked on the development of Safety Performance Indicators (SPIs) on seven road safety related areas. These SPIs reflect the operational conditions of the road traffic system that influence the system's safety performance. SPIs were developed

Operational Safety Performance Indicators and Balanced Scorecard in HANARO

International Nuclear Information System (INIS)

Wu, Jong-Sup; Jung, Hoan-Sung; Ahn, Guk-Hoon; Lee, Kye-Hong; Lim, In-Cheol; Kim, Hark-Rho

2007-01-01

Research reactors need an extensive basis for ensuring their safety. The importance of a safety management in nuclear facilities and activities has been emphasized. The safety activities in HANARO have been continuously conducted to enhance its safe operation. Last year, HANARO prepared two indicator sets to measure and assess the safety status of the reactor's operation and utilization. One is Safety Performance Indicators (SPI) and the other is Balanced Scorecard (BSC). Through reviewing these indicators, we can obtain the following information; - Plant safety status - Safety parameter trends - Safety information, for example, reactor operation status and radiation safety HANARO will continuously pursue the trends of SPI and BSC

Development of Safety Culture Indicators for HANARO

International Nuclear Information System (INIS)

Wu, Jong-Sup; Lee, Kye-Hong

2007-01-01

Safety culture is more important than a technical matter for the management of nuclear facilities. Some of the accidents that have occurred recently in nuclear plants are important as a social problem besides a technical problem. That's why the management of nuclear plants has been focused on the safety culture to improve confidence of nuclear facilities. As for a safety culture, there are difficulties in that a tangible result does not come out clearly in spite of an effort for a long time. Some IAEA guides and reports about a safety culture and its evaluation method for nuclear power plants (NPP) were published after the Chernobyl accident. Until now there is no tool to evaluate a safety culture of for research reactors. HANARO developed its own safety culture indicators based on the IAEA's documents. The purpose of the development of the safety culture indicators is to evaluate and enhance the safety attitude in HANARO

Food safety performance indicators to benchmark food safety output of food safety management systems.

Science.gov (United States)

Jacxsens, L; Uyttendaele, M; Devlieghere, F; Rovira, J; Gomez, S Oses; Luning, P A

2010-07-31

There is a need to measure the food safety performance in the agri-food chain without performing actual microbiological analysis. A food safety performance diagnosis, based on seven indicators and corresponding assessment grids have been developed and validated in nine European food businesses. Validation was conducted on the basis of an extensive microbiological assessment scheme (MAS). The assumption behind the food safety performance diagnosis is that food businesses which evaluate the performance of their food safety management system in a more structured way and according to very strict and specific criteria will have a better insight in their actual microbiological food safety performance, because food safety problems will be more systematically detected. The diagnosis can be a useful tool to have a first indication about the microbiological performance of a food safety management system present in a food business. Moreover, the diagnosis can be used in quantitative studies to get insight in the effect of interventions on sector or governmental level. Copyright 2010 Elsevier B.V. All rights reserved.

[A set of quality and safety indicators for hospitals of the "Agencia Valenciana de Salud"].

Science.gov (United States)

Nebot-Marzal, C M; Mira-Solves, J J; Guilabert-Mora, M; Pérez-Jover, V; Pablo-Comeche, D; Quirós-Morató, T; Cuesta Peredo, D

2014-01-01

To prepare a set of quality and safety indicators for Hospitals of the «Agencia Valenciana de Salud». The qualitative technique Metaplan® was applied in order to gather proposals on sustainability and nursing. The catalogue of the «Spanish Society of Quality in Healthcare» was adopted as a starting point for clinical indicators. Using the Delphi technique, 207 professionals were invited to participate in the selecting the most reliable and feasible indicators. Lastly, the resulting proposal was validated with the managers of 12 hospitals, taking into account the variability, objectivity, feasibility, reliability and sensitivity, of the indicators. Participation rates varied between 66.67% and 80.71%. Of the 159 initial indicators, 68 were prioritized and selected (21 economic or management indicators, 22 nursing indicators, and 25 clinical or hospital indicators). Three of them were common to all three categories and two did not match the specified criteria during the validation phase, thus obtaining a final catalogue of 63 indicators. A set of quality and safety indicators for Hospitals was prepared. They are currently being monitored using the hospital information systems. Copyright © 2013 SECA. Published by Elsevier Espana. All rights reserved.

Safety Performance Indicator for alcohol in road accidents--international comparison, validity and data quality.

Science.gov (United States)

Assum, Terje; Sørensen, Michael

2010-03-01

Safety Performance Indicators, SPIs, are developed for various areas within road safety such as speed, car occupant protection, alcohol and drugs, vehicle safety, etc. SPIs can be used to indicate the road safety situation and to compare road safety performance between countries and over time and to understand the process leading to accidents, helping to select the measures to reduce them. This article describes an alcohol SPI defined as the percentage of fatalities resulting from accidents involving at least one driver impaired by alcohol. The calculation of the alcohol SPI for 26 European countries shows that the SPI varies from 4.4% in Bulgaria to 72.2% in Italy. These results raise the question if the results reflect the real situation or if there is a methodological explanation. To answer this question three different studies were carried out: comparison with other alcohol SPIs, in-depth studies of data quality in seven selected countries, and a study of correlations between the SPI and influencing factors. These studies indicate clearly that there is a need to improve quality of the data used for the alcohol SPI. Most importantly, the total number of drivers involved in fatal accidents, the number tested for alcohol and the number not tested, should be reported, in addition to the number of alcohol positive and negative drivers among those tested. Until these improvements are made, the validity of this SPI seems poor and comparison of the alcohol SPI results across countries should be made with caution. Copyright 2009 Elsevier Ltd. All rights reserved.

Management and organizational indicators of process safety

International Nuclear Information System (INIS)

Van Hemel, S.B.; Connelly, E.M.; Haas, P.M.

1991-01-01

This study is part of a Nuclear Regulatory Commission research element on organizational factors in plant safety under the Human Factors research program. This paper reports that the study investigated the chemical industry, to find leading management or organizational tools which could be useful for the NRC. After collecting information form a variety of information sources, the authors concentrated our study on two types of indicators currently in use: the first is audit- or review-based, and concentrates on programmatic factors; the second, based on frequent behavioral observations, concentrates on the management of individual worker behaviors. The authors analyzed data on the relationships between the leading indictors and direct indictors such as accident and injury rates in three case studies, to determine whether sufficient evidence of validity and utility exists to justify consideration of these indicators as public safety indicators. This paper states that on the basis of statistical associations and other evidence, the authors concluded that the two indicator types have promise for use as plant safety performance indicators, and that further development and testing of the candidate indicators should be performed

Selection and verification of safety parameters in safety parameter display system for nuclear power plants

International Nuclear Information System (INIS)

Zhang Yuangfang

1992-02-01

The method and results for safety parameter selection and its verification in safety parameter display system of nuclear power plants are introduced. According to safety analysis, the overall safety is divided into six critical safety functions, and a certain amount of safety parameters which can represent the integrity degree of each function and the causes of change are strictly selected. The verification of safety parameter selection is carried out from the view of applying the plant emergency procedures and in the accident man oeuvres on a full scale nuclear power plant simulator

One safety critical indicators model for regulatory actions on nuclear power plants based on a level 1 PSA

International Nuclear Information System (INIS)

Araujo, Jefferson Borges

2006-03-01

This study presents a general methodology to the establishment, selection and use of safety indicators for a two loop PWR plant, as Angra 1. The study performed identifies areas considered critical for the plant operational safety. For each of these areas, strategic sub-areas are defined. For each strategic sub-area, specific safety indicators are defined. These proposed Safety Indicators are based on the contribution to risk considering a quantitative risk analysis. For each safety indicator, a goal, a bounded interval and proper bases are developed, to allow for a clear and comprehensive individual behavior evaluation. Additionally, an integrated evaluation of the indicators, using expert systems, was done to obtain an overview of the plant general safety. This methodology can be used for identifying situations where the plant safety is challenged, by giving a general overview of the plant operational condition. Additionally, this study can also identify eventual room for improvements by generating suggestions and recommendations, as a complement for regulatory actions and inspections, focusing resources on eventual existing weaknesses, in order to increase or maintain a high pattern of operational safety. (author)

The use of probabilistic safety assessment based maintenance indicators to increase the availability of safety related systems in nuclear power plants

International Nuclear Information System (INIS)

Kirchsteiger, C.

1991-04-01

This work describes the theoretical development of a Probabilistic Safety Assessment (PSA) based Performance Indicator (PI) model for a comprehensive Maintenance Efficiency Analysis (MEA) and its practical application to past operational history data of a certain Nuclear Power Plant. Plant specific equipment history and maintenance work order data have been collected and analysed using various advanced statistical procedures (nonparametric methods, multivariate analysis) in order to be able to estimate safety system related equipment and maintenance process trends. The main results of such a MEA case study are the trends in the (in)effectiveness of the performance of a selected safety system and its dominant maintenance related causes of its bad (good) equipment performance. Finally, the therefrom gained results are used to propose a new set of safety system based and maintenance related Performance Indicators, including suggestions for a corresponding plant specific maintenance data collection system. (author)

Food safety performance indicators to benchmark food safety output of food safety management systems

NARCIS (Netherlands)

Jacxsens, L.; Uyttendaele, M.; Devlieghere, F.; Rovira, J.; Oses Gomez, S.; Luning, P.A.

2010-01-01

There is a need to measure the food safety performance in the agri-food chain without performing actual microbiological analysis. A food safety performance diagnosis, based on seven indicators and corresponding assessment grids have been developed and validated in nine European food businesses.

The use of probabilistic safety assessment (PSA) based maintenance indicators to increase the availability of safety related systems in nuclear power plants

International Nuclear Information System (INIS)

Kirchsteiger, C.

1991-04-01

This work describes the theoretical development of a Probabilistic Safety Assessment (PSA) based Performance Indicator (PI) model for a comprehensive Maintenance Efficiency Analysis (MEA) and its practical application to past operational history data of a certain nuclear power plant. Plant specific equipment history and maintenance work on data have been collected and analysed using various advanced statistical procedures (nonparametric methods, multivariate analysis in order to be able to estimate safety system related equipment and maintenance process trends. The main results of such a MEA case study are the trends in the (in)effectiveness of the performance of a selected safety system and its dominant components as well as the detection of the dominant maintenance related causes of its bad (good) equipment performance. Finally, the therefrom gained results are used to propose a new set of safety system-based and maintenance-related performance indicators, including suggestions for a corresponding plant specific maintenance data collection system. (author)

Safety system function trend indicator: Theory and test application

International Nuclear Information System (INIS)

Azarm, M.A.; Carbonaro, J.F.; Boccio, J.L.; Vesely, W.E.

1989-01-01

The purpose of this paper is to summarize research conducted on the development and validation of quantitative indicators of safety performance. This work, performed under the Risk-Based Performance Indicator (RBPI) Project, FIN A-3295, for the Office of Research (RES), is considered part of NRC's Performance Indicator Program which is being coordinated through the Office for the Analysis and Evaluation of Operational Data (AEOD). The program originally focused on risk-based indicators at high levels of safety indices (e.g., core-damage frequency, functional unavailabilities, and sequence monitoring). The program was then redirected towards a more amenable goal, safety system unavailability indicators, mainly due to the lack of PRA models and plant data. In that regard, BNL published a technical report that introduced the concept of cycle-based indicators and also described various alternatives of monitoring safety system unavailabilities. Further simplification of these indicators was requested by NRC to facilitate their applications to all plants in a timely manner. This resulted in the development of Safety System Function Trend (SSFT) indicators which minimize the need for detailed system model as well as component history. The theoretical bases for these indicators were developed through various simulation studies to determine the ease of detecting a trend and/or unacceptable performance. These indicators, along with several other indicators, were then generated and compared using plant data as a part of a test application. The SSFT indicators, specifically, were constructed for a total of eight plants, consisting of two systems per plant. Emphasis was placed on examining relative changes, as well as the indicator's actual level. Both the trend and actual indicator level were found to be important in identifying plants with potential problems

Processes on Uncontrolled Aerodromes and Safety Indicators - Part II

Directory of Open Access Journals (Sweden)

Vladimír Plos

2014-01-01

Full Text Available This article follows on the Part I, where the basic processes on uncontrolled aerodromes were introduced. The uncontrolled aerodromes face with the growing traffic and from that result the higher workload on AFIS officer. This means a higher potential for dangerous situations.The article describes some models of sub-processes and creates several safety indicators related to the operation at uncontrolled aerodromes. Thanks to monitoring and evaluation of safety indicators can be adopted targeted safety measures and thus increase safety on small uncontrolled aerodromes.

Airport Ground Operations Risks and Establishment of the Safety Indicators

Directory of Open Access Journals (Sweden)

Slobodan Stojić

2016-07-01

Full Text Available This paper brings a relatively new approach to air transport safety. This approach introduces the safety indicators whose application’s primer goal is to reduce the number of aviation safety events and to search for their causes. These causes are defined as factors contributing to safety event realisation. These are supposed to be adequately identified and then prevented or at least mitigated. Defined safety indicators are focused on airport processes and subjects.

Operational safety performance indicator system at the Dukovany Nuclear Power Plant - Experience with indicator aggregation

International Nuclear Information System (INIS)

Mandula, J.

2001-01-01

The operational safety performance indicators serve as an important tool of performance monitoring and management at the Dukovany NPP. A software-supported system has been developed, which has included: data collection, central data storage, graphic output production and periodical report generation. Analyses of performance indicator trends together with evaluation in respect of annually updated target values and acceptance criteria are used for operational safety reviews forming an integral part of continual self-assessment process. This contribution has been focused on experience obtained during development of the operational safety assessment model using indicator aggregation. It summarises problems that had to be paid specific attention in the development process. Thanks to their solution, the model has become a synoptic monitor and a useful tool for operational safety assessment. (author)

A road safety performance indicator for vehicle fleet compatibility.

NARCIS (Netherlands)

Christoph, M. Vis, M.A. Rackliff, L. & Stipdonk, H.

2013-01-01

This paper discusses the development and the application of a safety performance indicator which measures the intrinsic safety of a country's vehicle fleet related to fleet composition. The indicator takes into account both the ‘relative severity’ of individual collisions between different vehicle

Indicators to monitor NPP safety performance. Working material

International Nuclear Information System (INIS)

1997-01-01

Numerical indicators to monitor safety status and overall safety performance of nuclear power plants (NPPs) are used by operators and some regulators worldwide. During the last few years, the IAEA, through Technical Committee Meetings and Consultants' Meetings has worked on this area. This report presents a framework for nuclear power plant safety performance indicators that was developed during two consultant meetings held at the IAEA headquarters in Vienna in December 1995 and November 1996. Annex 2 on risk based indicators was prepared during a consultants' meeting held in Vienna in July 1996. An additional outcome from these activities, was the recommendation that the IAEA conduce pilot exercises at several nuclear power plants that might be interested to participate, in order to test the validity of the concept and its usefulness. 6 figs

Operational safety performance indicators for nuclear power plants

International Nuclear Information System (INIS)

2000-05-01

Since the late 1980s, the IAEA has been actively sponsoring work in the area of indicators to monitor nuclear power plant (NPP) operational safety performance. The early activities were mainly focused on exchanging ideas and good practices in the development and use of these indicators at nuclear power plants. Since 1995 efforts have been directed towards the elaboration of a framework for the establishment of an operational safety performance indicator programme. The result of this work, compiled in this publication, is intended to assist NPPs in developing and implementing a monitoring programme, without overlooking the critical aspects related to operational safety performance. The framework proposed in this report was presented at two IAEA workshops on operational safety performance indicators held in Ljubljana, Slovenia, in September 1998 and at the Daya Bay NPP, Szenzhen, China, in December 1998. During these two workshops, the participants discussed and brainstormed on the indicator framework presented. These working sessions provided very useful insights and ideas which where used for the enhancement of the framework proposed. The IAEA is acknowledging the support and contribution of all the participants in these two activities. The programme development was enhanced by pilot plant studies. Four plants from different countries with different designs participated in this study with the objective of testing the applicability, usefulness and viability of this approach

A road safety performance indicator for vehicle fleet compatibility.

Science.gov (United States)

Christoph, Michiel; Vis, Martijn Alexander; Rackliff, Lucy; Stipdonk, Henk

2013-11-01

This paper discusses the development and the application of a safety performance indicator which measures the intrinsic safety of a country's vehicle fleet related to fleet composition. The indicator takes into account both the 'relative severity' of individual collisions between different vehicle types, and the share of those vehicle types within a country's fleet. The relative severity is a measure for the personal damage that can be expected from a collision between two vehicles of any type, relative to that of a collision between passenger cars. It is shown how this number can be calculated using vehicle mass only. A sensitivity analysis is performed to study the dependence of the indicator on parameter values and basic assumptions made. The indicator is easy to apply and satisfies the requirements for appropriate safety performance indicators. It was developed in such a way that it specifically scores the intrinsic safety of a fleet due to its composition, without being influenced by other factors, like helmet wearing. For the sake of simplicity, and since the required data is available throughout Europe, the indicator was applied to the relative share of three of the main vehicle types: passenger cars, heavy goods vehicles and motorcycles. Using the vehicle fleet data from 13EU Member States and Norway, the indicator was used to rank the countries' safety performance. The UK was found to perform best in terms of its fleet composition (value is 1.07), while Greece has the worst performance with the highest indicator value (1.41). Copyright © 2013 Elsevier Ltd. All rights reserved.

The spin project: safety and performance indicators in different time frames

International Nuclear Information System (INIS)

Storck, R.; Becker, D.A.

2002-01-01

Safety and performance indicators have been under discussion for many years in several countries and international organisations. If those indicators refer to the long term safety of the total disposal system, they are often called safety indicators. If they refer to the performance of subsystems or the total system from a more technical point of view, they are sometimes called performance indicators. The need for indicators other than dose rates derives e.g. from the long time frames involved in safety assessments of waste disposal systems and the increasing uncertainty in dose rate calculations over time due to uncertainty in evolution of the surface environment and of behaviour of man. Before introducing additional indicators into a safety case of a potential repository site, the applicability and usefulness of different indicators have to be investigated and evaluated. The systematic analysis and testing of safety and performance indicators for use in different time horizons after closure of the disposal facility is the task of the SPIN project. This is done by re-calculating four recent studies concerning repository projects in granite formations. (authors)

The safety indicators program in Taiwan, China : a six-year trend

International Nuclear Information System (INIS)

Hsu, Mingte

1998-01-01

This paper presents data on the current operating status and the safety indicators (SI) of the six nuclear power units in Taiwan. Analysis of the data collected in a six-year period has been made to obtain trends for each safety indicator. An overview of the trends of the plant operational data during the same period are also provided and discussed. On the whole, the trends of safety indicators are improving during the observed period 1991-1996. The plant operational data have depicted coherent improvement with the safety indicator trends. This result supports the premise that improvements in safety performance and in operational reliability are correspondingly inter-dependent. Both the safety indicators quarterly report and the annual report are available to the public. The public can also approach this information from the AEC's World Wide Web site (http://www.aec.gov.tw). (author)

Risk-based safety performance indicators for nuclear power plants

International Nuclear Information System (INIS)

Chakraborty, S.; Prohaska, G.; Flodin, Y.; Grint, G.; Habermacher, H.; Hallman, A.; Isasia, R.; Melendez, E.; Verduras, E.; Karsa, Z.; Khatib-Rahbar, M.; Koeberlein, K.; Schwaeger, C.; Matahri, N.; Moravcik, I.; Tkac, M.; Preston, J.

2003-01-01

In a Concerted Action (CA), sponsored by the European Commission within its 5th Framework Program, a consortium of eleven partners from eight countries has reviewed and evaluated the application of Safety Performance Indicators (SPIs), which - in combination with other tools - can be used to monitor and improve the safety of nuclear power plants. The project was aimed at identification of methods that can be used in a risk-informed regulatory system and environment, and to exploit PSA techniques for the development and use of meaningful additional/alternative SPIs. The CA included the review of existing indicator systems, and the collection of information on the experience from indicator systems by means of a specific questionnaire. One of the most important and challenging issues for nuclear plant owners and/or regulators is to recognize early signs of deterioration in safety performance, caused by influences from management, organization and safety culture (MOSC), before actual events and/or mishaps take place. Most of the existing SPIs as proposed by various organizations are considered as 'lagging' indicators, that is, they are expected to show an impact only when a downward trend has already started. Furthermore, most of the available indicators are at a relatively high level, such that they will not provide useful information on fundamental weaknesses causing the problem in the first place. Regulators' and utilities' views on the use of a Safety Performance Indicator System have also been a part of the development of the CA. (author)

A pattern of contractor selection for oil and gas industries in a safety approach using ANP-DEMATEL in a Grey environment.

Science.gov (United States)

Gharedaghi, Gholamreza; Omidvari, Manouchehr

2018-01-11

Contractor selection is one of the major concerns of industry managers such as those in the oil industry. The objective of this study was to determine a contractor selection pattern for oil and gas industries in a safety approach. Assessment of contractors based on specific criteria and ultimately selecting an eligible contractor preserves the organizational resources. Due to the safety risks involved in the oil industry, one of the major criteria of contractor selection considered by managers today is safety. The results indicated that the most important safety criterion of contractor selection was safety records and safety investments. This represented the industry's risks and the impact of safety training and investment on the performance of other sectors and the overall organization. The output of this model could be useful in the safety risk assessment process in the oil industry and other industries.

[Quality of care and safety indicators in anticoagulated patients with non-valvular auricular fibrillation and deep venous thromboembolic disease].

Science.gov (United States)

Ignacio, E; Mira, J J; Campos, F J; López de Sá, E; Lorenzo, A; Caballero, F

2018-03-19

To identify and prioritise indicators to assess the quality of care and safety of patients with non-valvular auricular fibrillation (NVAF) and deep vein thrombosis (DVT) treated with anticoagulants. Using the consensus conference technique, a group of professionals and clinical experts, the determining factors of the NVAF and DVT care process were identified, in order to define the quality and safety criteria. A proposal was made for indicators of quality and safety that were prioritised, taking into account a series of pre-established attributes. The selected indicators were classified into indicators of context, safety, action, and outcomes of the intervention in the patient. A set of 114 health care and safety quality indicators were identified, of which 35 were prioritised: 15 for NVAF and 20 for DVT. About half (49%) of the indicators (40% for NVAF and 55% for DVT) applied to patient safety, and 26% (33% for NVAF and 20% for DVT) to the outcomes of interventions in the patient. The present work presents a set of agreed indicators by a group of expert professionals that can contribute to the improvement of the quality of care of patients with NVAF and DVT treated with anticoagulants. Copyright © 2018 SECA. Publicado por Elsevier España, S.L.U. All rights reserved.

Safety performance indicators used by the Russian Safety Regulatory Authority in its practical activities on nuclear power plant safety regulation

International Nuclear Information System (INIS)

Khazanov, A.L.

2005-01-01

The Sixth Department of the Nuclear, Industrial and Environmental Regulatory Authority of Russia, Scientific and Engineering Centre for Nuclear and Radiation Safety process, analyse and use the information on nuclear power plants (NPPs) operational experience or NPPs safety improvement. Safety performance indicators (SPIs), derived from processing of information on operational violations and analysis of annual NPP Safety Reports, are used as tools to determination of trends towards changing of characteristics of operational safety, to assess the effectiveness of corrective measures, to monitor and evaluate the current operational safety level of NPPs, to regulate NPP safety. This report includes a list of the basic SPIs, those used by the Russian safety regulatory authority in regulatory activity. Some of them are absent in list of IAEA-TECDOC-1141 ('Operational safety performance indicators for nuclear power plants'). (author)

Safety- and performance indicators for a generic deep geological repository in clay

International Nuclear Information System (INIS)

Resele, G.; Niemeyer, M.; Wilhelm, St.; Heimer, St.; Mohlfeld, M.; Eilers, G.; Preuss, J.; Wollrath, J.

2010-01-01

Document available in extended abstract form only. As a first step of an impartial survey for an optimal site selection for a deep geological repository in Germany, potentially suitable regions shall be identified and localised according to their suitability. During the early phases of such a site selection procedure the information about the properties of the host rock and the geological situation at the potential sites is not very precise. As site investigation procedures are both expensive and time-consuming, it is essential to identify those properties of the geological barrier system that are most relevant for long-term safety. Furthermore, adequate indicators have to be chosen that allow a simple but efficient assessment of the suitability of the potential regions. Definition and application of 'exclusion criteria' based on single parameter values, e.g. the hydraulic conductivity of the host rock, is inadequate because the long-term safety depends on the interaction of many features and properties of the barrier system. In a research project, indicators have been developed which depend on the most relevant properties of the geological barriers and estimate the overall performance of a repository system. The application of these indicators on the barrier properties which have been found during the investigations of potential repository sites in clay located in Germany, Switzerland and France demonstrates how, for instance, an unfavourably high hydraulic permeability of the clay can be compensated by a large vertical extension of the clay layer and small hydraulic gradients. Other indicators evaluate the importance of hydraulic discontinuities and define the minimal requirements on technical barriers like seals and backfill of emplacement tunnels. When the information of the radionuclide inventory and the biosphere, especially the diluting aquifer is included, the indicators allow the estimation of the resulting dose which matches the result of a

Road safety performance indicators for the interurban road network.

NARCIS (Netherlands)

Yannis, G. Weijermars, W.A.M. Gitelman, V. Vis, M. Chazirisa, A. Papadimitriou, E. & Lima Azevedo, C.

2013-01-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The

Development of the NUMO pre-selection, site-specific safety case

International Nuclear Information System (INIS)

Fujiyama, Tetsuo; Suzuki, Satoru; Deguchi, Akira; Umeki, Hiroyuki

2016-01-01

Key conclusions: ◆ “The NUMO pre-selection, site-specific safety case” provides the basic structure for subsequent safety cases that will be applied to any selected site, emphasising practical approaches and methodology which will be applicable for the conditions/constraints during an actual siting process. ◆ The preliminary results of the design and safety assessment would underpin the feasibility and safety of geological disposal in Japan.

Indicators for Monitoring Water, Sanitation, and Hygiene: A Systematic Review of Indicator Selection Methods

Directory of Open Access Journals (Sweden)

Stefanie Schwemlein

2016-03-01

Full Text Available Monitoring water, sanitation, and hygiene (WaSH is important to track progress, improve accountability, and demonstrate impacts of efforts to improve conditions and services, especially in low- and middle-income countries. Indicator selection methods enable robust monitoring of WaSH projects and conditions. However, selection methods are not always used and there are no commonly-used methods for selecting WaSH indicators. To address this gap, we conducted a systematic review of indicator selection methods used in WaSH-related fields. We present a summary of indicator selection methods for environment, international development, and water. We identified six methodological stages for selecting indicators for WaSH: define the purpose and scope; select a conceptual framework; search for candidate indicators; determine selection criteria; score indicators against criteria; and select a final suite of indicators. This summary of indicator selection methods provides a foundation for the critical assessment of existing methods. It can be used to inform future efforts to construct indicator sets in WaSH and related fields.

Natural safety indicators and their application to repository safety cases

International Nuclear Information System (INIS)

Miller, B.

2002-01-01

Radiological dose and risk are the standard end-points calculated in all performance assessments. Their calculation requires, however, assumptions to be made for future human behaviour. To complement dose and risk, other safety indicators have been suggested which do not require such assumptions to be made. One proposed set of safety indicators are the concentrations and fluxes of naturally-occurring chemical species in the environment which may be compared with the performance assessment predictions of repository releases. Such comparisons can be valid because both the natural and repository species would occur in the same system and their transport behaviour would be controlled by exactly the same processes at the same rates. Although simple in concept, there is currently no consensus on the most appropriate comparisons to make or on the interpretation of such comparisons. A number of national and international research projects are evaluating this proposed approach, including an IAEA Co-ordinated Research Programme. These projects suggest that that the approach appears to be workable and that it may be a valuable component of a safety case, complementing the dose and risk presentations. Further work is, however, necessary to develop the approach to a level where it may be confidently applied in further performance assessments in a consistent and methodical manner. (author)

Long term safety requirements and safety indicators for the assessment of underground radioactive waste repositories

International Nuclear Information System (INIS)

Vovk, Ivan

1998-01-01

This presentation defines: waste disposal, safety issues, risk estimation; describes the integrated waste disposal process including quality assurance program. Related to actinides inventory it shows the main results of calculated activity obtained by deterministic estimation. It includes the Radioactive Waste Safety Standards and requirements; features related to site, design and waste package characteristics, as technical long term safety criteria for radioactive waste disposal facilities. Fundamental concern regarding the safety of radioactive waste disposal systems is their radiological impact on human beings and the environment. Safety requirements and criteria for judging the level of safety of such systems have been developed and there is a consensus among the international community on their basis within the well-established system of radiological protection. So far, however, little experience has been gained in applying long term safety criteria to actual disposal systems; consequently, there is an international debate on the most appropriate nature and form of the criteria to be used, taking into account the uncertainties involved. Emerging from the debate is the increasing conviction that the combined use of a variety of indicators would be advantageous in addressing the issue of reasonable assurance in the different time frames involved and in supporting the safety case for any particular repository concept. Indicators including risk, dose, radionuclide concentration, transit time, toxicity indices, fluxes at different points within the system, and barrier performance have all been identified as potentially relevant. Dose and risk are the indicators generally seen as most fundamental, as they seek directly to describe the radiological impact of a disposal system, and these are the ones that have been incorporated into most national standards to date. There are, however, certain problems in applying them. Application of a variety of different indicators

Inter-comparison of safety culture within selected practices in Ghana utilising ionising radiation

International Nuclear Information System (INIS)

Faanu, A.; Schandorf, C.; Darko, E. O.; Boadu, M.; Emi-Reynolds, G.; Awudu, A. R.; Gyekye, P. K.; Kpeglo, D. O.

2010-01-01

The safety culture of selected practices and facilities in Ghana utilising radiation sources or radiation emitting devices has been assessed using a performance indicator, which provided status information on management and operating staff commitment to safety. The questionnaire was based on the following broad areas: general safety considerations, safety policy at the facility level, safety practices at the facility level, definition of responsibility, staff training, safety of the physical structure of the facility and the emergency plans. The analysis showed that the percentage levels of commitment to safety for the respective practices are as follows: conventional radiography, 23.3-90.0%; research reactor, 73.3 %; gamma irradiation facility, 53.3%; radiotherapy, 76.7%; X-ray scanner, 80.0%; gamma scanner, 76.7%; industrial radiography 86.7% and nuclear density practice, 78%. None of the practices or facilities was able to satisfy all the requirements that will ensure a 100% level of safety culture. (authors)

Safety in surgery: is selection the missing link?

Science.gov (United States)

Paice, Alistair G; Aggarwal, Rajesh; Darzi, Ara

2010-09-01

Health care providers comprise an example of a "high risk organization." Safety failings within these organizations have the potential to cause significant public harm. Significant safety improvements in other high risk organizations such as the aviation industry have led to the concept of a high reliability organization (HRO)--a high risk organization that has enjoyed a prolonged safety record. A strong organizational culture is common to all successful HROs, encompassing powerful systems of selection and training. Aircrew selection processes provide a good example of this and are examined in detail in this article using the Royal Air Force process as an example. If the lessons of successful HROs are to be applied to health care organizations, candidate selection to specialties such as surgery must become more objective and robust. Other HROs can provide valuable lessons in how this may be approached.

Leading and lagging indicators of occupational health and safety: The moderating role of safety leadership.

Science.gov (United States)

Sheehan, Cathy; Donohue, Ross; Shea, Tracey; Cooper, Brian; Cieri, Helen De

2016-07-01

In response to the call for empirical evidence of a connection between leading and lagging indicators of occupational health and safety (OHS), the first aim of the current research is to consider the association between leading and lagging indicators of OHS. Our second aim is to investigate the moderating effect of safety leadership on the association between leading and lagging indicators. Data were collected from 3578 employees nested within 66 workplaces. Multi-level modelling was used to test the two hypotheses. The results confirm an association between leading and lagging indicators of OHS as well as the moderating impact of middle management safety leadership on the direct association. The association between leading and lagging indicators provides OHS practitioners with useful information to substantiate efforts within organisations to move away from a traditional focus on lagging indicators towards a preventative focus on leading indicators. The research also highlights the important role played by middle managers and the value of OHS leadership development and investment at the middle management level. Copyright © 2016 Elsevier Ltd. All rights reserved.

A proposal of safety indicators aggregation to assess the safety management effectiveness of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Jose Antonio B.; Saldanha, Pedro L.C. [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil). Coordenacao-Geral de Reatores e Ciclo Combustivel], e-mail: jantonio@cnen.gov.br, e-mail: saldanha@cnen.gov.br; Melo, Paulo F.F. Frutuoso e [Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear], e-mail: frutuoso@con.ufrj.br

2009-07-01

Safety management has changed with the evolution of management methods, named Quality Systems, moving from Quality Control, where the focus was the product, passing through Quality Assurance, which takes care of the whole manufacturing process and reaching the Total Quality Management, where policies and goals are established. Nowadays, there is a trend towards Management Systems, which integrate all different aspects related to the management of an organization (safety, environment, security, quality, costs and, etc), but it is necessary to have features to establish and assure that safety overrides the remaining aspects. The most usual way to reach this goal is to establish a policy where safety is a priority, but its implementation and the assessment of its effectiveness are no so simple. Nuclear power plants usually have over a hundred safety indicators in many processes dedicated to prevent and detect problems, although a lot of them do not evaluate these indicators in an integrated manner or point out degradation trends of organizational aspects, which can affect the plant safety. This work develops an aggregation of proactive and reactive safety indicators in order to evaluate the effectiveness of nuclear power plant safety management and to detect, at early stages, signs of process degradation or activities used to establish, maintain and assure safety conditions. The aggregation integrates indicators of the usual processes and is based on the manner the management activities have been developed in the last decades, that is: Planning, Doing, Checking and Acting - known as PDCA cycle - plus a fifth element related to the capability of those who perform safety activities. The proposed aggregation is in accordance to Brazilian standards and international recommendations and constitutes a friendly link between the top management level and the daily aspects of the organization. (author)

A proposal of safety indicators aggregation to assess the safety management effectiveness of nuclear power plants

International Nuclear Information System (INIS)

Carvalho, Jose Antonio B.; Saldanha, Pedro L.C.; Melo, Paulo F.F. Frutuoso e

2009-01-01

Safety management has changed with the evolution of management methods, named Quality Systems, moving from Quality Control, where the focus was the product, passing through Quality Assurance, which takes care of the whole manufacturing process and reaching the Total Quality Management, where policies and goals are established. Nowadays, there is a trend towards Management Systems, which integrate all different aspects related to the management of an organization (safety, environment, security, quality, costs and, etc), but it is necessary to have features to establish and assure that safety overrides the remaining aspects. The most usual way to reach this goal is to establish a policy where safety is a priority, but its implementation and the assessment of its effectiveness are no so simple. Nuclear power plants usually have over a hundred safety indicators in many processes dedicated to prevent and detect problems, although a lot of them do not evaluate these indicators in an integrated manner or point out degradation trends of organizational aspects, which can affect the plant safety. This work develops an aggregation of proactive and reactive safety indicators in order to evaluate the effectiveness of nuclear power plant safety management and to detect, at early stages, signs of process degradation or activities used to establish, maintain and assure safety conditions. The aggregation integrates indicators of the usual processes and is based on the manner the management activities have been developed in the last decades, that is: Planning, Doing, Checking and Acting - known as PDCA cycle - plus a fifth element related to the capability of those who perform safety activities. The proposed aggregation is in accordance to Brazilian standards and international recommendations and constitutes a friendly link between the top management level and the daily aspects of the organization. (author)

IAEA activities related to safety indicators, time frames and reference scenarios

International Nuclear Information System (INIS)

Batandjieva, B.; Hioki, K.; Metcalf, P.

2002-01-01

The fundamental principles for the safe management of radioactive waste have been agreed internationally and form the basis for the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management that entered into force in June 2001. Protection of human health and the environment and safety of facilities (including radioactive waste disposal facilities) are widely recognised principles to be followed and demonstrated in post-closure safety assessment of waste repositories. Dose and risk are at present internationally agreed safety criteria, used for judging the acceptability of such facilities. However, there have been a number of activities initiated and co-ordinated by the International Atomic Energy Agency (IAEA) which have provided an international forum for discussion and consensus building on the use safety indicators which are complementary to dose and risk. The Agency has been working on the definition of other safety indicators, such as flux, time, environmental concentration, etc.; the desired characteristics, and use of these indicators in different time frames. The IAEA has focused on safety indicators related to geological disposal, exploring their role in the development of a safety case, evaluating the advantages and disadvantages of using other safety indicators and how they complement the dose and risk indicators. The use of these indicators have been discussed also from regulatory perspective, mainly in terms of achieving reasonable assurance and confidence in safety assessments for waste repositories and decision making in the presence of uncertainty in the context of disposal of long-lived waste. Considerable effort has also been expended by the Agency on the development and application of principles for defining critical groups and biospheres for deep geological repositories. One of the important and successful IAEA programmes in this field is the Biosphere Modelling and Assessment (BIOMASS) project

Safety culture indicators for NPP: international trends and development status in Korea

International Nuclear Information System (INIS)

Choi, Y. S.; Ko, J. D.; Choi, K. S.; Jung, Y. H.

2004-01-01

Safety culture has been recognized as important to achieve high level of nuclear safety, as several recent events that have occurred in advanced countries were found to have important implications for safety culture. Under the recognition, implementation-focused and practical methods to foster safety culture have become necessary. Development of safety culture indicators for assessing the level of safety culture and identifying some deficiencies is being conducted. This paper examines the regulatory positions of major nuclear power countries on licensee's safety culture, introduces the development status of Korean Safety Culture Indicators and presents its future direction

Nuclear power indices and safety

International Nuclear Information System (INIS)

Bennet, L.L.; Fizher, D.; Nechaev, A.

1987-01-01

Problems discussed at the IAEA International Conference on nuclear power indices and safety held in Vienna from 28 September to 2 October, 1987 are considered. Representatives from 40 countries and 12 international organizations participated in the conference. It is marked that by the end of this century nuclear power plant capacities in developing countries will increase by more than twice. In developed countries increase of installed capacity by 65 % is forecasted. It is stressed that competently constructed and operated NPPs will be successfully competing with coal-fueled power plants in the majority of the world regions. Much attention was paid to reports on measures taken after Chernobyl' accident and its radiation effects on people helth. It is shown that parallel with fundamental theoretical studies on NPP safety as a complex engineering system much attention is paid to some problems of designing and operation of such facilities. Fuel cycle problems, radioactive waste and spent fuel storage and disposal in particular, are considered

Bertolette Selected as EHS Champion of Safety | Poster

Science.gov (United States)

Dan Bertolette has been selected as the most recent NCI at Frederick Champion of Safety, as part of the Champions of Safety Program sponsored by the Environment, Health, and Safety Program (EHS). The goal of the program, which began last year, is to raise awareness and promote a culture of safety by showing NCI at Frederick staff at work in their respective workplaces, according to Terri Bray, director, EHS. “Since we have so many varied work environments here, safety often takes on a different look, according to workplace. We want to take the opportunity to show real people in real situations, to encourage safety everywhere,” Bray said.

[An approach to care indicators benchmarking. Learning to improve patient safety].

Science.gov (United States)

de Andrés Gimeno, B; Salazar de la Guerra, R M; Ferrer Arnedo, C; Revuelta Zamorano, M; Ayuso Murillo, D; González Soria, J

2014-01-01

Improvements in clinical safety can be achieved by promoting a safety culture, professional training, and learning through benchmarking. The aim of this study was to identify areas for improvement after analysing the safety indicators in two public Hospitals in North-West Madrid Region. Descriptive study performed during 2011 in Hospital Universitario Puerta de Hierro Majadahonda (HUPHM) and Hospital de Guadarrama (HG). The variables under study were 40 indicators on nursing care related to patient safety. Nineteen of them were defined in the SENECA project as care quality standards in order to improve patient safety in the hospitals. The data collected were clinical history, Madrid Health Service assessment reports, care procedures, and direct observation Within the 40 indicators: 22 of them were structured (procedures), HUPHM had 86%, and HG 95% 14 process indicators (training and protocols compliance) with similar results in both hospitals, apart from the care continuity reports and training in hand hygiene. The 4 results indicators (pressure ulcer, falls and pain) showed different results. The analysis of the indicators allowed the following actions to be taken: to identify improvements to be made in each hospital, to develop joint safety recommendations in nursing care protocols in prevention and treatment of chronic wound, to establish systematic pain assessments, and to prepare continuity care reports on all patients transferred from HUPHM to HG. Copyright © 2013 SECA. Published by Elsevier Espana. All rights reserved.

Comparative assessment of safety indicators for vehicle trajectories on the highway

NARCIS (Netherlands)

Mullakkal Babu, F.A.; Wang, M.; Farah, H.; van Arem, B.; Happee, R.

2017-01-01

Safety measurement and analysis have been a challenging and well-researched topic in transportation. Conventionally, surrogate safety measures have been used as safety indicators in simulation models for safety assessment, in control formulations for driver assistance systems, and in data analysis

Plant safety and performance indicators for regulatory use

International Nuclear Information System (INIS)

Ferjancic, M.; Nemec, T.; Cimesa, S.

2004-01-01

Slovenian Nuclear Safety Administration (SNSA) supervises nuclear and radiological safety of Krsko NPP. This SNSA supervision is performed through inspections, safety evaluations of plant modifications and event analyses as well as with the safety and performance indicators (SPI) which are a valuable data source for plant safety monitoring. In the past SNSA relied on the SPI provided by Krsko NPP and did not have a set of SPI which would be more appropriate for regulatory use. In 2003 SNSA started with preparation of a new set of SPI which would be more suitable for performing the regulatory oversight of the plant. New internal SNSA procedure which is under preparation will define use and evaluation of SPI and will include definitions for the proposed set of SPI. According to the evaluation of SPI values in comparison with the limiting values and/or trending, the procedure will define SNSA response and actions. (author)

DEVELOPING SAFETY INDICATORS ON THE BASIS OF THE ICAO RECOMMENDATIONS

Directory of Open Access Journals (Sweden)

V. D. Sharov

2014-01-01

Full Text Available The article offers direct use of the recommendations of SMM ICAO Doc.9859, 3rd ed. 2013, for calculation the target and alert levels of safety indicators. Examples of calculation based on data of 2011 and monitoring of the current indicators during 2012 are presented. Safety indicators for airlines in terms of “numbers of incidents per 1000 flight hours” could be calculated on the basis of the state values through the «coefficient of conformity».

Development of Behavioral Indicators of Competences for Safety Culture of Nuclear Power Plants: A Preliminary Study

International Nuclear Information System (INIS)

Moon, Kwangsu; Kim, Sa Kil; Oh, Yeon Ju; Shin, Youmin; Lee, Yong-Hee; Jang, Tong Il

2015-01-01

determine the method of measurement. Mainly used tools for behavior observations are Critical Behavior Checklist (CBC), Behaviorally Anchored Rating Scale (BARS), Behavior Observation Scale (BOS), and Mixed Standard Scale (MSS). Each measure is used differently depending on the occurrence likelihood and dimension of behavior. Therefore, further study is needed in order to determine the most appropriate technique for effective and efficient measuring behavioral indicators in practice. In the future study, there are additional considerations to apply the suggested set of safety culture competences to any specific NPP. In general, five to seven core competences are recommended for efficient competence management, it is required to prioritize the importance of each competence among all competences through the field validation including actual behavior observation and discussion with incumbents. Moreover, it is better to select core competences across various types of jobs (operator, maintenance/repair, experiment and so on) because the priority of each competence may be different across job types. In addition, only the safety culture competence for field employees was proposed in this study

Development of Behavioral Indicators of Competences for Safety Culture of Nuclear Power Plants: A Preliminary Study

Energy Technology Data Exchange (ETDEWEB)

Moon, Kwangsu; Kim, Sa Kil; Oh, Yeon Ju; Shin, Youmin; Lee, Yong-Hee; Jang, Tong Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

determine the method of measurement. Mainly used tools for behavior observations are Critical Behavior Checklist (CBC), Behaviorally Anchored Rating Scale (BARS), Behavior Observation Scale (BOS), and Mixed Standard Scale (MSS). Each measure is used differently depending on the occurrence likelihood and dimension of behavior. Therefore, further study is needed in order to determine the most appropriate technique for effective and efficient measuring behavioral indicators in practice. In the future study, there are additional considerations to apply the suggested set of safety culture competences to any specific NPP. In general, five to seven core competences are recommended for efficient competence management, it is required to prioritize the importance of each competence among all competences through the field validation including actual behavior observation and discussion with incumbents. Moreover, it is better to select core competences across various types of jobs (operator, maintenance/repair, experiment and so on) because the priority of each competence may be different across job types. In addition, only the safety culture competence for field employees was proposed in this study.

Selected Indicators of Adolescent Violence & Safety at School.

Science.gov (United States)

Mikow, Victoria A.

Fights, weapons, and stolen or intentionally damaged property are common concerns of most schools in North Carolina. The results of this survey indicate that 27 percent of all 9th-12th grade students reported carrying a weapon (gun, knife, club) within the month prior to this survey. A significant percentage of students do not feel safe at school…

Design of an indicator for health and safety governance

OpenAIRE

Minguillón, Roberto F.; Yacuzzi, Enrique

2009-01-01

Occupational Health and Safety Governance (OHSG) is a branch of Corporate Governance by which the board directs and controls labor risks created by their own enterprise. The OHSG concept is relatively new; unlike Occupational Health and Safety Management, which is mostly related to the work of managerial ranks, OHSG deals with principles, the interests of stakeholders, and the work of directors. The paper defines the new concept, OHSG, develops an original health and safety indicator, and pre...

Economic Indicators Selected Countries.

Science.gov (United States)

1987-12-01

DEFENCE I ECONOMIC INDICATORS SELECTED COUNTRIES DECEMBER QUARTER 1987 . ’-H ISSUED BY MANPOWER POLICY & STRATEGIES BRANCH " "’ :.S S ’,1l f ,am -m mW...100 Sour:e: Main Economic Indicators (OECD) Manufactured Basic Metal Year Goods Chemicals Metals Products 1980 100 100 100 100 1981 110 117 102 107...Earnings of all 1982 1986 7.4 Male Employees (a) Aug 1986 Aug 1987 4.8 Hourly Wace Rates 3 1979 1987 lt.2 Garden Island 1983 1987 6.7 Dockyards Dec

Method for selection of optimal road safety composite index with examples from DEA and TOPSIS method.

Science.gov (United States)

Rosić, Miroslav; Pešić, Dalibor; Kukić, Dragoslav; Antić, Boris; Božović, Milan

2017-01-01

Concept of composite road safety index is a popular and relatively new concept among road safety experts around the world. As there is a constant need for comparison among different units (countries, municipalities, roads, etc.) there is need to choose an adequate method which will make comparison fair to all compared units. Usually comparisons using one specific indicator (parameter which describes safety or unsafety) can end up with totally different ranking of compared units which is quite complicated for decision maker to determine "real best performers". Need for composite road safety index is becoming dominant since road safety presents a complex system where more and more indicators are constantly being developed to describe it. Among wide variety of models and developed composite indexes, a decision maker can come to even bigger dilemma than choosing one adequate risk measure. As DEA and TOPSIS are well-known mathematical models and have recently been increasingly used for risk evaluation in road safety, we used efficiencies (composite indexes) obtained by different models, based on DEA and TOPSIS, to present PROMETHEE-RS model for selection of optimal method for composite index. Method for selection of optimal composite index is based on three parameters (average correlation, average rank variation and average cluster variation) inserted into a PROMETHEE MCDM method in order to choose the optimal one. The model is tested by comparing 27 police departments in Serbia. Copyright © 2016 Elsevier Ltd. All rights reserved.

NRC performance indicator program

International Nuclear Information System (INIS)

Singh, R.N.

1987-01-01

The performance indicator development work of the US Nuclear Regulatory Commission (NRC) interoffice task group involved several major activities that included selection of candidate indicators for a trial program, data collection and review, validation of the trial indicators, display method development, interactions with the industry, and selection of an optimum set of indicators for the program. After evaluating 27 potential indicators against certain ideal attributes, the task group selected 17 for the trial program. The pertinent data for these indicators were then collected from 50 plants at 30 sites. The validation of the indicators consisted of two primary processes: logical validity and statistical analysis. The six indicators currently in the program are scrams, safety system actuations, significant events, safety system failures, forced outage rate, and equipment forced outages per 100 critical hours. A report containing data on the six performance indicators and some supplemental information is issued on a quarterly basis. The NRC staff is also working on refinements of existing indicators and development of additional indicators as directed by the commission

New method for distance-based close following safety indicator.

Science.gov (United States)

Sharizli, A A; Rahizar, R; Karim, M R; Saifizul, A A

2015-01-01

The increase in the number of fatalities caused by road accidents involving heavy vehicles every year has raised the level of concern and awareness on road safety in developing countries like Malaysia. Changes in the vehicle dynamic characteristics such as gross vehicle weight, travel speed, and vehicle classification will affect a heavy vehicle's braking performance and its ability to stop safely in emergency situations. As such, the aim of this study is to establish a more realistic new distance-based safety indicator called the minimum safe distance gap (MSDG), which incorporates vehicle classification (VC), speed, and gross vehicle weight (GVW). Commercial multibody dynamics simulation software was used to generate braking distance data for various heavy vehicle classes under various loads and speeds. By applying nonlinear regression analysis to the simulation results, a mathematical expression of MSDG has been established. The results show that MSDG is dynamically changed according to GVW, VC, and speed. It is envisaged that this new distance-based safety indicator would provide a more realistic depiction of the real traffic situation for safety analysis.

Geographical indications, food safety, and sustainability: conflicts and synergies

Directory of Open Access Journals (Sweden)

David A. Wirth

2017-01-01

Full Text Available This paper examines the legal and policy relationships amongst international standards for GIs, food safety requirements, and voluntary claims related to a food’s attributes. The paper addresses those relationships within the context of international trade agreements protecting GIs, such as the 1994 TRIPS Agreement, the EU-Canada Comprehensive Economic and Trade Agreement (CETA, and the chapter on intellectual property and geographical indications in the Transatlantic Trade and Investment Partnership (TTIP currently under negotiation. Trade agreements also discipline food safety measures and non-GI indications of quality or safety such as “organic” and “GMO-free.” Accordingly, the paper also considers the extent to which international trade agreements such as the WTO Agreements on the Application of Sanitary and Phytosanitary Standards (SPS Agreement and Technical Barriers to Trade (TBT might interact with the analysis.

Safety and performance indicators for the assessment of long-term safety of deep geological disposal of radioactive waste

International Nuclear Information System (INIS)

Hugi, M.; Schneider, J.W.; Dorp, F. van; Zuidema, P.

2005-01-01

The evaluation of the ability to isolate radioactive waste and the assessment of the long-term safety of a deep geological repository is usually done in terms of the calculated dose and/or risk for an average individual of the population which is potentially most affected by the potential impacts of the repository. At present, various countries and international organisations are developing so-called complementary indicators to supplement such calculations. These indicators are called ''safety indicators'' if they refer to the safety of the whole repository system; if they address the isolation capability of individual system components or the whole system from a more technical perspective, they are called ''performance indicators''. The need for complementary indicators follows from the long time frames which characterise the safety assessment of a geological repository, and the corresponding uncertainty of the calculated radiation dose. The main reason for these uncertainties is associated with the uncertain long-term prognosis of the surface environment and the related human behaviour. (orig.)

Safety and performance indicators for repositories in salt and clay formations

International Nuclear Information System (INIS)

Wolf, Jens; Ruebel, Andre; Noseck, Ulrich; Becker, Dirk

2008-07-01

The GRS (Gesellschaft fuer Reaktorsicherheit) study aims to the identification of suitable indicators for repositories in salt and clay formation. It is not intended to compare the two formations with respect to the safe disposal of radioactive waste. A first set of safety and performance indicators for both host rocks has been derived on the basis of results of the SPIN project. Reference values for the safety indicators have been determined. The suitability of the indicators and their significance for different time frames Is demonstrated by means of deterministic model calculations and external parameter variations of previous studies. The safety indicators considered in the report are the effective dose rate (Sv/a), the radiotoxicity concentration in the biosphere water (Sv/m 3 ) and the radiotoxicity flux from the geosphere (overlying rock) (Sv/a). The performance indicators considered in the study are the radiotoxicity inventory in different compartments (S), radiotoxicity fluxes from compartments and the integrated radiotoxicity fluxes from compartments (Sv).

Radiological impacts analysis with use of new endpoint as complementary safety indicators

International Nuclear Information System (INIS)

Peralta Vital, J.L.; Gil Castillo, R.; Fleitas Estevez, G.G.; Olivera Acosta, J.

2015-01-01

The paper shows the new safety indicators on risk assessment (safety assessment) to radioactive waste environmental management implementation (concentrations and fluxes of naturally occurring radioactive materials (NORM)). The endpoint obtained, allow the best analysis of the radiological impact associated to radioactive waste isolation system. The common safety indicators for safety assessment purpose, dose and risk, are very time dependent, increasing the uncertainties in the results for long term assessment. The complementary and new proposed endpoints are more stable and they are not affected by changes in the critical group, pathways, etc. The NORM values on facility site were obtained as result of national surveys, the natural concentrations of U, Ra, Th, K has been associated with the variation of the lithologies in 3 geographical areas of the Country (Occidental, Central and Oriental). The results obtained are related with the safety assessment topics and allowed to apply the new complementary safety indicators, by comparisons between the natural concentrations and fluxes on site and its calculated values for the conceptual repository design. In order to normalize the concentration results, the analysis was realized adopting the criteria of the Repository Equivalent Rock Volume (RERV). The preliminary comparison showed that the calculated concentrations and fluxes in the Cuban conceptual radioactive waste repository are not higher than the natural values in the host rock. According to the application of new safety indicators, the reference disposal facility does not increase the natural activity concentration and fluxes in the environment. In order to implement these new safety indicator it has been used the current 226 Ra inventory of the Repository and the 226 Ra as natural concentration on the site. (authors)

Application of patient safety indicators internationally: a pilot study among seven countries.

Science.gov (United States)

Drösler, Saskia E; Klazinga, Niek S; Romano, Patrick S; Tancredi, Daniel J; Gogorcena Aoiz, Maria A; Hewitt, Moira C; Scobie, Sarah; Soop, Michael; Wen, Eugene; Quan, Hude; Ghali, William A; Mattke, Soeren; Kelley, Edward

2009-08-01

To explore the potential for international comparison of patient safety as part of the Health Care Quality Indicators project of the Organization for Economic Co-operation and Development (OECD) by evaluating patient safety indicators originally published by the US Agency for Healthcare Research and Quality (AHRQ). A retrospective cross-sectional study. Acute care hospitals in the USA, UK, Sweden, Spain, Germany, Canada and Australia in 2004 and 2005/2006. Routine hospitalization-related administrative data from seven countries were analyzed. Using algorithms adapted to the diagnosis and procedure coding systems in place in each country, authorities in each of the participating countries reported summaries of the distribution of hospital-level and overall (national) rates for each AHRQ Patient Safety Indicator to the OECD project secretariat. Each country's vector of national indicator rates and the vector of American patient safety indicators rates published by AHRQ (and re-estimated as part of this study) were highly correlated (0.821-0.966). However, there was substantial systematic variation in rates across countries. This pilot study reveals that AHRQ Patient Safety Indicators can be applied to international hospital data. However, the analyses suggest that certain indicators (e.g. 'birth trauma', 'complications of anesthesia') may be too unreliable for international comparisons. Data quality varies across countries; undercoding may be a systematic problem in some countries. Efforts at international harmonization of hospital discharge data sets as well as improved accuracy of documentation should facilitate future comparative analyses of routine databases.

Application of patient safety indicators internationally: a pilot study among seven countries

NARCIS (Netherlands)

Drösler, Saskia E.; Klazinga, Niek S.; Romano, Patrick S.; Tancredi, Daniel J.; Gogorcena Aoiz, Maria A.; Hewitt, Moira C.; Scobie, Sarah; Soop, Michael; Wen, Eugene; Quan, Hude; Ghali, William A.; Mattke, Soeren; Kelley, Edward

2009-01-01

To explore the potential for international comparison of patient safety as part of the Health Care Quality Indicators project of the Organization for Economic Co-operation and Development (OECD) by evaluating patient safety indicators originally published by the US Agency for Healthcare Research and

Indicators of Nuclear safety and exploitation in ANAV

International Nuclear Information System (INIS)

Quintana Prieto, M.; Jorda Alcove, M.

2013-01-01

The use of indicators by ANAV plants, aims to be a tool to facilitate the assessment of the behaviour of the plants nuclear over a specific time period. The following are and are they explain those related to Nuclear safety and exploitation.

Analysis of international approaches which are used at development of theoperational safety performance indicators

International Nuclear Information System (INIS)

Lyigots'kij, O.Yi.; Nosovs'kij, A.V.; Chemeris, Yi.O.

2009-01-01

Description of international approaches and experience of the use of theoperational safety performance indicators system is provided for estimationof current status and making a decision on corrections in the operationpractice. The state of development of the operational safety performanceindicators system by the operating organization is overviewed. Thepossibility of application of international approaches during development ofthe integral safety performance indicators system is analyzed. Aims and tasksof future researches are formulated in relation to development of theintegral safety performance indicators system.

The use of safety indicators in the assessment of radioactive waste disposal

International Nuclear Information System (INIS)

Wingefors, S.; Westerlind, M.; Gera, F.

1999-01-01

The most widely used criteria for disposal are limits or constraints on individual dose or risk, and these have been introduced in most national legal frameworks. There is general agreement that future generations have the right to the same level of protection as the current generation. Even if quantitative criteria corresponding to the required level of protection can be (and have been) defined, it is a great challenge to demonstrate compliance with these criteria. The difficulties are to large extent due to the long time-scales needed to be considered in radioactive waste disposal. The future cannot be predicted in detail but instead different scenarios, with different probabilities of occurrence, must be assessed. Some parts of a disposal system can be predicted or analysed with high confidence for very long periods of time, e.g. geological formations, while for example the evolution of the biosphere, and in particular the society, become quite uncertain within less than one thousand years. Thus, there may be considerable uncertainty in doses (or risks) derived from the safety assessment of a repository. Due to these unavoidable uncertainties it is believed advantageous to use multiple approaches in the safety assessment and to identify different indicators for the repository safety ('multiple-lines-of-reasoning'). The most fundamental safety indicators are dose/risk but complementary indicators have been suggested, in particular flux and environmental concentration of radionuclides. This presentation is focussed on fluxes and concentrations as complementary safety indicators. Other safety indicators, e.g. transfer times, are mentioned only briefly

Measuring individual work performance: identifying and selecting indicators.

Science.gov (United States)

Koopmans, Linda; Bernaards, Claire M; Hildebrandt, Vincent H; de Vet, Henrica C W; van der Beek, Allard J

2014-01-01

Theoretically, individual work performance (IWP) can be divided into four dimensions: task performance, contextual performance, adaptive performance, and counterproductive work behavior. However, there is no consensus on the indicators used to measure these dimensions. This study was designed to (1) identify indicators for each dimension, (2) select the most relevant indicators, and (3) determine the relative weight of each dimension in ratings of work performance. IWP indicators were identified from multiple research disciplines, via literature, existing questionnaires, and expert interviews. Subsequently, experts selected the most relevant indicators per dimension and scored the relative weight of each dimension in ratings of IWP. In total, 128 unique indicators were identified. Twenty-three of these indicators were selected by experts as most relevant for measuring IWP. Task performance determined 36% of the work performance rating, while the other three dimensions respectively determined 22%, 20% and 21% of the rating. Notable consensus was found on relevant indicators of IWP, reducing the number from 128 to 23 relevant indicators. This provides an important step towards the development of a standardized, generic and short measurement instrument for assessing IWP.

Selection of safety officers in an indian construction organization by using grey relational analysis

Directory of Open Access Journals (Sweden)

Sunku Venkata Siva Rajaprasad

2018-03-01

Full Text Available Stakeholders are responsible for implementing the occupational health and safety provisions in an organization. Irrespective of organization, the role of safety department is purely advisory as it coordinates with all the departments, and this is crucial to improve the performance. Selection of safety officer is vital job for any organization; it should not only be based on qualifications of the applicant, the incumbent should also have sufficient exposure in implementing proactive measures. The process of selection is complex and choosing the right safety professional is a vital decision. The safety performance of an organization relies on the systems being implemented by the safety officer. Application of multi criteria decision-making tools is helpful as a selection process. The present study proposes the grey relational analysis(GRA for selection of the safety officers in an Indian construction organization. This selection method considers fourteen criteria appropriate to the organization and has ranked the results. The data was also analyzed by using technique for order Preference by Similarity to an Ideal solution (TOPSIS and results of both the methods are strongly correlated

Numerical indicators of nuclear power plant safety performance

International Nuclear Information System (INIS)

1991-04-01

The workshop was attended by representatives from twenty-two Member States operating nuclear power plants (NPP). The current status of the development and use of numerical indicators of NPP safety performance was presented. A consensus on the benefits of use of numerical indicators was reached. The Technical Committee Meeting reviewed the progress in the development and use of performance indicators and identified them as the most appropriate ones for international use. The purpose of this document is to summarize the discussions held and conclusions reached in both meetings. Lists of participants and all the papers of both meetings are presented

Safety indicators for the safety assessment of radioactive waste disposal. Sixth report of the Working Group on Principles and Criteria for Radioactive Waste Disposal

International Nuclear Information System (INIS)

2003-09-01

The report describes a few indicators that are considered to be the most promising for assessing the long term safety of disposal systems. The safety indicators that are discussed here may be applicable to a range of disposal systems for different waste types, including near surface disposal facilities for low level waste. The appropriateness of the different indicators may, however, vary depending on the characteristics of the waste, the facility and the assessment context. The focus of the report is thus on the use of time-scales of containment and transport, and radionuclide concentrations and fluxes, as indicators of disposal system safety, that may complement the more usual safety indicators of dose and risk. Summarised are the broad elements that a safety case for an underground radioactive waste disposal facility should possess and the role and use of performance and safety indicators within these elements. An overview of performance and safety indicators is given. The use is discussed of dose and risk as safety indicators and, in particular, problems that can arise in their use. Also presented are some specific indicators that have the potential to be used as complementary safety indicators. Discussed is also how fluxes of naturally occurring elements and radionuclides due to the operation of natural processes such as erosion and groundwater discharge may be quantified for comparison with fluxes of waste derived contaminants

International survey of living PSA and safety indicators

International Nuclear Information System (INIS)

Holmberg, J.; Laakso, K.; Lehtinen, E.; Bjoere, S.

1992-01-01

The report contains an international overview of applications of living probabilistic assessment and development of operational safety indicators. Features of an ideal living PSA tool are summarized as well as a limited survey of code systems for managing a living probabilistic safety assessment (living PSA) is included. The international survey is used as an input for planning and performance of related tasks within the nordic NKS/SIK-1 project conducted in 1990-93. The research notes are distributed to the Nordic organizations involved or interested in the subject. The report includes an overview and conclusions from technical reports and articles available and presentations and discussions related to development and use of above methods for the evaluation and management of the operational safety of nuclear power plants. A large part of this material is based on material collected and discussed in connection to international specialist meetings relating to the subject

A Framework Based on a Systems Approach to Developing Safety Indicators in Fish Farming

Directory of Open Access Journals (Sweden)

Siri Mariane Holen

2018-05-01

Full Text Available The fish farming industry is one of the industries in Norway with the highest occupational fatality and injury rate. Despite the serious health, safety, and environmental issues in the industry, little is done to measure changes in safety over time beyond the traditional Lost Time Injury (LTI registrations. In this article the objective is twofold; (i to propose a framework for developing safety indicators based on Systems-Theoretic Process Analysis (STPA, and (ii to apply the framework to find indicators relevant for hazards in operations where subcontractors participate. STPA uses a hierarchical portrayal of the system in focus, in contrast to sequential models, and views safety as a control problem. It is believed that a systemic approach to indicator development better captures the complex safety challenges in aquaculture. Thirteen indicators are identified within areas such as maintenance, training, and planning. The indicators identified may function as a basis for decisions and actions that must be undertaken to ensure safe operations.

Key issues on safety design basis selection and safety assessment

International Nuclear Information System (INIS)

An, S.; Togo, Y.

1976-01-01

In current fast reactor design in Japan, four design accident conditions and four design seismic conditions are adopted as the design base classifications. These are classified by the considerations on both likelihood of occurrence and the severeness of the consequences. There are several major problem areas in safety design consideration such as core accident problems which include fuel sodium interaction, fuel failure propagation and residual decay heat removal, and decay heat removal systems problems which is more or less the problem of selection of appropriate system and of assurance of high reliability of the system. In view of licensing, two kinds of accidents are postulated in evaluating the adequacy of a reactor site. The one is the ''major accident'' which is the accident to give most severe radiation hazard to the public from technical point of view. The other is the ''hypothetical accident'', induced public accident of which is severer than that of major accident. While the concept of the former is rather unique to Japanese licensing, the latter is almost equivalent to design base hypothetical accident of the US practice. In this paper, design bases selections, key safety issues and some of the licensing considerations in Japan are described

Comparison of Country Risk, Sustainability and Economic Safety Indices

Directory of Open Access Journals (Sweden)

Jelena Stankeviciene

2014-03-01

Full Text Available Country risk, sustainability an economic safety are becoming more important in the contemporary economic world. The aim of this paper is to present the importance of comparison formalisation of country risk, sustainability, and economic safety indices for strategic alignment. The work provides an analysis on the relationship between country risk, sustainability an economic safety in EU countries, based on statistical data. Investigations and calculations of rankings provided by Euromoney Country Risk Index, European Economic Sustainability Index as well as for Economic Security Index were made and the results of EU country ranking based on three criteria were provided. Furthermore, the data for the Baltic States was summarised and the corresponding index of consistency for random judgments was evaluated.

Indicators for monitoring of safety operation and condition of nuclear power stations

International Nuclear Information System (INIS)

Manova, D.

2001-01-01

A common goal of all employees in the nuclear power field is safety operation of nuclear power stations. The evaluation and control of NPP safety operation are a part of the elements of safety management. The present report is related only to a part of the total assessment and control of the plant safety operation, namely - the indicator system for monitoring of Kozloduy NPP operation and condition. (author)

Factor analysis improves the selection of prescribing indicators

DEFF Research Database (Denmark)

Rasmussen, Hanne Marie Skyggedal; Søndergaard, Jens; Sokolowski, Ineta

2006-01-01

OBJECTIVE: To test a method for improving the selection of indicators of general practitioners' prescribing. METHODS: We conducted a prescription database study including all 180 general practices in the County of Funen, Denmark, approximately 472,000 inhabitants. Principal factor analysis was us...... appropriate and inappropriate prescribing, as revealed by the correlation of the indicators in the first factor. CONCLUSION: Correlation and factor analysis is a feasible method that assists the selection of indicators and gives better insight into prescribing patterns....

An observational study of road safety around selected primary schools in Ibadan municipality, Oyo State, Southwestern Nigeria.

Science.gov (United States)

Sangowawa, Adesola O; Adebiyi, Akindele O; Faseru, Babalola; Popoola, Olusola J

2012-01-01

Child pedestrians have been identified as vulnerable road users. Although walking as a means of transport has health and other benefits, it exposes children to the risk of road traffic injuries. This study was conducted to assess the availability of road safety features around government-owned primary schools in Ibadan municipality. A multistage sampling technique was used to select 46 of the 74 schools in the study area. Some (11) of the selected schools were sited within the same premises and shared a common entrance; thus a total of 35 school premises were eventually observed. Trained research assistants observed the school environment around the selected schools for road safety features such as location of schools, presence of "school", "child crossing" and "speed limit" road signs, and presence of traffic calming devices (road bumps or zebra crossing). Five (14%) of the schools were located on major roads and eight (23%) had road signs indicating that a school was nearby. Seven (20%) had road bumps close to the school, 15 (43%) had a warden who assisted children to cross, and none had a zebra crossing. Five (14%) schools had pedestrian sidewalks. The study revealed that the environment around a number of the observed schools in the municipality compromised the pupils' road safety. The local government, school authorities, parents, and road safety professionals need to institute definite measures to enhance the road safety environment around schools in the municipality.

Bringing structure into road safety evaluation: a hierarchy of indicators

OpenAIRE

HERMANS, Elke; BRIJS, Tom; WETS, Geert; SHEN, Yongjun

2010-01-01

In recent years, there has been an explosion of interest in indicators in several domains. This reflects growing recognition of the important role indicators can play as a tool for enhancing the quality of decision making. Indicators express an aspect of a phenomenon in an understandable and relevant way and are useful in terms of monitoring, evaluation and communication. Like other policies, road safety policy could benefit from the use of indicators able to measure changes and progress towa...

Bringing structure into road safety evaluation: a hierarchy of indicators

OpenAIRE

HERMANS, Elke; BRIJS, Tom; WETS, Geert

2010-01-01

In recent years, there has been an explosion of interest in indicators in several domains. This reflects growing recognition of the important role indicators can play as a tool for enhancing the quality of decision making. Indicators express an aspect of a phenomenom in an understandable and relevant way and are useful in terms of monitoring, evaluation and communication. Like other policies, road safety policy could benefit from the use of indicators able to measure changes and progress towa...

Optimal safety levels via social indicators

International Nuclear Information System (INIS)

Lind, N.C.; Nathwani, J.S.

1992-01-01

In the management of natural or technological hazards in a society, the objective should be to serve the public interest in a rational manner. Decisions with regard to risk levels for the public - if they are to be defensible and self-consistent - require an integrated system of values that covers the entire range of hazards under public regulation. The process for setting risk levels (or safety goals) should ideally involve a thorough consideration of cost and benefit of all kinds, supported by explicit quantified comparison on a widely acceptable scale. The purpose of the paper is to show how quantitative criteria within the context of an appropriate framework can be used to guide risk management decisions. Social indicators are time series, statistics that reflect some aspect of the quality of life in a society or group of individuals. Development, validation, and use of social indicators is an important current research activity, as exemplified by journals such as Social Indicators Research. The basic objective is to provide quantitative measures for assessing the rationales and effectiveness of public decision-making. The concept is applicable to the nuclear industry

The role of safety analyses in site selection. Some personal observations based on the experience from the Swiss site selection process

Energy Technology Data Exchange (ETDEWEB)

Zuidema, Piet [Nagra, Wettingen (Switzerland)

2015-07-01

In Switzerland, the site selection process according to the ''Sectoral Plan for Deep Geological Repositories'' (BFE 2008) is underway since 2008. This process takes place in three stages. In stage 1 geological siting regions (six for the L/ILW repository and three for the HLW repository) have been identified, in stage 2 sites for the surface facilities have been identified for all siting regions in close co-operation with the sting regions and a narrowing down of the number of siting regions based on geological criteria will take place. In stage 3 the sites for a general license application are selected and the general license applications will be submitted which eventually will lead to the siting decision for both repository types. In the Swiss site selection process, safety has the highest priority. Many factors affect safety and thus a whole range of safety-related issues are considered in the identification and screening of siting possibilities. Besides dose calculations a range of quantitative and qualitative issues are considered. Dose calculations are performed in all three stages of the site selection process. In stage 1 generic safety calculations were made to develop criteria to be used for the identification of potential siting regions. In stage 2, dose calculations are made for comparing the different siting regions according to a procedure prescribed in detail by the regulator. Combined with qualitative evaluations this will lead to a narrowing down of the number of siting regions to at least two siting regions for each repository type. In stage 3 full safety cases will be prepared as part of the documentation for the general license applications. Besides the dose calculations, many other issues related to safety are analyzed in a quantitative and qualitative manner. These consider the 13 criteria defined in the Sectoral Plan and the corresponding indicators. The features analyzed cover the following broad themes: efficiency of

The role of safety analyses in site selection. Some personal observations based on the experience from the Swiss site selection process

International Nuclear Information System (INIS)

Zuidema, Piet

2015-01-01

In Switzerland, the site selection process according to the ''Sectoral Plan for Deep Geological Repositories'' (BFE 2008) is underway since 2008. This process takes place in three stages. In stage 1 geological siting regions (six for the L/ILW repository and three for the HLW repository) have been identified, in stage 2 sites for the surface facilities have been identified for all siting regions in close co-operation with the sting regions and a narrowing down of the number of siting regions based on geological criteria will take place. In stage 3 the sites for a general license application are selected and the general license applications will be submitted which eventually will lead to the siting decision for both repository types. In the Swiss site selection process, safety has the highest priority. Many factors affect safety and thus a whole range of safety-related issues are considered in the identification and screening of siting possibilities. Besides dose calculations a range of quantitative and qualitative issues are considered. Dose calculations are performed in all three stages of the site selection process. In stage 1 generic safety calculations were made to develop criteria to be used for the identification of potential siting regions. In stage 2, dose calculations are made for comparing the different siting regions according to a procedure prescribed in detail by the regulator. Combined with qualitative evaluations this will lead to a narrowing down of the number of siting regions to at least two siting regions for each repository type. In stage 3 full safety cases will be prepared as part of the documentation for the general license applications. Besides the dose calculations, many other issues related to safety are analyzed in a quantitative and qualitative manner. These consider the 13 criteria defined in the Sectoral Plan and the corresponding indicators. The features analyzed cover the following broad themes: efficiency of

Proceedings of the specialist meeting on safety performance indicators

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-28

In 1998, the OECD/NEA committee on Nuclear Regulatory Activities (CNRA) initiated an activity with the objective of advancing the discussion on how to enhance and measure regulatory effectiveness in relation to nuclear installations. One of the outcome of this activity was to establish a Task group to develop internal (direct) performance indicators which would be used to monitor regulatory efficiency. On the initiative of the NEA/CSNI Working Group on Operating Experience the Spanish CSN hosted a workshop (Madrid, 2000) to review the state of the art on Safety Performance Indicators. This workshop, which was co-sponsored by the IAEA and WANO was attended by 73 participants from 19 countries, representing the industry, regulators, service companies as well as international organisations. The conclusions were: 1. there is considerable development effort on performance indicators in many countries; 2. utilities continue to rely on the WANO Performance indicators system which consists of indicators in 8 key areas and receives data from virtually all commercial NPP's in the world; 3. Regulators do not have a common set of performance indicators. This document gathers the 25 presentations given during this workshop. After this workshop, a joint CNRA/CSNI task group was launched in December 2000 to exchange information and develop external (indirect) indicators to measure regulatory effectiveness, i.e. impact on licensee's safety performance. These external indicators are, in other words, the traditional plant performance indicators (PI's). The task force consisted of regulators, organisations which have a performance indicators system in operation or under testing. The task force met in Paris on February 19-20, 2001 and the work performed by the group is summarized in a report (NEA-CSNI-R--2001-11) attached in appendix to these proceedings.

Proceedings of the specialist meeting on safety performance indicators

International Nuclear Information System (INIS)

2002-01-01

In 1998, the OECD/NEA committee on Nuclear Regulatory Activities (CNRA) initiated an activity with the objective of advancing the discussion on how to enhance and measure regulatory effectiveness in relation to nuclear installations. One of the outcome of this activity was to establish a Task group to develop internal (direct) performance indicators which would be used to monitor regulatory efficiency. On the initiative of the NEA/CSNI Working Group on Operating Experience the Spanish CSN hosted a workshop (Madrid, 2000) to review the state of the art on Safety Performance Indicators. This workshop, which was co-sponsored by the IAEA and WANO was attended by 73 participants from 19 countries, representing the industry, regulators, service companies as well as international organisations. The conclusions were: 1. there is considerable development effort on performance indicators in many countries; 2. utilities continue to rely on the WANO Performance indicators system which consists of indicators in 8 key areas and receives data from virtually all commercial NPP's in the world; 3. Regulators do not have a common set of performance indicators. This document gathers the 25 presentations given during this workshop. After this workshop, a joint CNRA/CSNI task group was launched in December 2000 to exchange information and develop external (indirect) indicators to measure regulatory effectiveness, i.e. impact on licensee's safety performance. These external indicators are, in other words, the traditional plant performance indicators (PI's). The task force consisted of regulators, organisations which have a performance indicators system in operation or under testing. The task force met in Paris on February 19-20, 2001 and the work performed by the group is summarized in a report (NEA-CSNI-R--2001-11) attached in appendix to these proceedings

Application of patient safety indicators internationally: a pilot study among seven countries

OpenAIRE

Drösler, Saskia E.; Klazinga, Niek S.; Romano, Patrick S.; Tancredi, Daniel J.; Gogorcena Aoiz, Maria A.; Hewitt, Moira C.; Scobie, Sarah; Soop, Michael; Wen, Eugene; Quan, Hude; Ghali, William A.; Mattke, Soeren; Kelley, Edward

2017-01-01

Objective To explore the potential for international comparison of patient safety as part of the Health Care Quality Indicators project of the Organization for Economic Co-operation and Development (OECD) by evaluating patient safety indicators originally published by the US Agency for Healthcare Research and Quality (AHRQ). Design A retrospective cross-sectional study. Setting Acute care hospitals in the USA, UK, Sweden, Spain, Germany, Canada and Australia in 2004 and 2005/2006. Data source...

Artificial neural network model for prediction of safety performance indicators goals in nuclear plants

Energy Technology Data Exchange (ETDEWEB)

Souto, Kelling C.; Nunes, Wallace W. [Instituto Federal de Educacao, Ciencia e Tecnologia do Rio de Janeiro, Nilopolis, RJ (Brazil). Lab. de Aplicacoes Computacionais; Machado, Marcelo D., E-mail: dornemd@eletronuclear.gov.b [ELETROBRAS Termonuclear S.A. (ELETRONUCLEAR), Rio de Janeiro, RJ (Brazil). Gerencia de Combustivel Nuclear - GCN.T

2011-07-01

Safety performance indicators have been developed to provide a quantitative indication of the performance and safety in various industry sectors. These indexes can provide assess to aspects ranging from production, design, and human performance up to management issues in accordance with policy, objectives and goals of the company. The use of safety performance indicators in nuclear power plants around the world is a reality. However, it is necessary to periodically set goal values. Such goals are targets relating to each of the indicators to be achieved by the plant over a predetermined period of operation. The current process of defining these goals is carried out by experts in a subjective way, based on actual data from the plant, and comparison with global indices. Artificial neural networks are computational techniques that present a mathematical model inspired by the neural structure of intelligent organisms that acquire knowledge through experience. This paper proposes an artificial neural network model aimed at predicting values of goals to be used in the evaluation of safety performance indicators for nuclear power plants. (author)

Artificial neural network model for prediction of safety performance indicators goals in nuclear plants

International Nuclear Information System (INIS)

Souto, Kelling C.; Nunes, Wallace W.; Machado, Marcelo D.

2011-01-01

Safety performance indicators have been developed to provide a quantitative indication of the performance and safety in various industry sectors. These indexes can provide assess to aspects ranging from production, design, and human performance up to management issues in accordance with policy, objectives and goals of the company. The use of safety performance indicators in nuclear power plants around the world is a reality. However, it is necessary to periodically set goal values. Such goals are targets relating to each of the indicators to be achieved by the plant over a predetermined period of operation. The current process of defining these goals is carried out by experts in a subjective way, based on actual data from the plant, and comparison with global indices. Artificial neural networks are computational techniques that present a mathematical model inspired by the neural structure of intelligent organisms that acquire knowledge through experience. This paper proposes an artificial neural network model aimed at predicting values of goals to be used in the evaluation of safety performance indicators for nuclear power plants. (author)

Is road safety management linked to road safety performance?

Science.gov (United States)

Papadimitriou, Eleonora; Yannis, George

2013-10-01

This research aims to explore the relationship between road safety management and road safety performance at country level. For that purpose, an appropriate theoretical framework is selected, namely the 'SUNflower' pyramid, which describes road safety management systems in terms of a five-level hierarchy: (i) structure and culture, (ii) programmes and measures, (iii) 'intermediate' outcomes'--safety performance indicators (SPIs), (iv) final outcomes--fatalities and injuries, and (v) social costs. For each layer of the pyramid, a composite indicator is implemented, on the basis of data for 30 European countries. Especially as regards road safety management indicators, these are estimated on the basis of Categorical Principal Component Analysis upon the responses of a dedicated road safety management questionnaire, jointly created and dispatched by the ETSC/PIN group and the 'DaCoTA' research project. Then, quasi-Poisson models and Beta regression models are developed for linking road safety management indicators and other indicators (i.e. background characteristics, SPIs) with road safety performance. In this context, different indicators of road safety performance are explored: mortality and fatality rates, percentage reduction in fatalities over a given period, a composite indicator of road safety final outcomes, and a composite indicator of 'intermediate' outcomes (SPIs). The results of the analyses suggest that road safety management can be described on the basis of three composite indicators: "vision and strategy", "budget, evaluation and reporting", and "measurement of road user attitudes and behaviours". Moreover, no direct statistical relationship could be established between road safety management indicators and final outcomes. However, a statistical relationship was found between road safety management and 'intermediate' outcomes, which were in turn found to affect 'final' outcomes, confirming the SUNflower approach on the consecutive effect of each layer

New Criteria of Indication and Selection of Patients to Cochlear Implant

Directory of Open Access Journals (Sweden)

André L. L. Sampaio

2011-01-01

Full Text Available Numerous changes continue to occur in cochlear implant candidacy. In general, these have been accompanied by concomitant and satisfactory changes in surgical techniques. Together, this has advanced the utility and safety of cochlear implantation. Most devices are now approved for use in patients with severe to profound unilateral hearing loss rather then the prior requirement of a bilateral profound loss. Furthermore, studies have begun utilizing short electrode arrays for shallow insertion in patients with considerable low-frequency residual hearing. This technique will allow the recipient to continue to use acoustically amplified hearing for the low frequencies simultaneously with a cochlear implant for the high frequencies. The advances in design of, and indications for, cochlear implants have been matched by improvements in surgical techniques and decrease in complications. The resulting improvements in safety and efficacy have further encouraged the use of these devices. This paper will review the new concepts in the candidacy of cochlear implant. Medline data base was used to search articles dealing with the following topics: cochlear implant in younger children, cochlear implant and hearing preservation, cochlear implant for unilateral deafness and tinnitus, genetic hearing loss and cochlear implant, bilateral cochlear implant, neuropathy and cochlear implant and neural plasticity, and the selection of patients for cochlear implant.

Leading safety performance indicators for resilience assessment of radiopharmaceuticals production process

International Nuclear Information System (INIS)

Grecco, Claudio H.S.; Santos, Isaac J.A.L.; Carvalho, Paulo V.R.

2011-01-01

Radiopharmaceuticals are radiation-emitting substances used in medicine for radiotherapy and imaging diagnosis. A Research Institute, located in Rio de Janeiro, produces three radiopharmaceuticals: the sodium iodate is used in the diagnosis of thyroid dysfunctions, the meta-iodo-benzyl guanidine is used in the diagnosis of cardiac diseases, and the fluorodeoxyglucose is used in diagnosis in cardiology, oncology, neurology and neuro psychiatry. This paper presents a leading safety performance indicators framework to assess the resilience of radiopharmaceuticals production processes. The organizations that use resilience indicators will be able to pro actively evaluate and manage safety. (author)

Leading safety performance indicators for resilience assessment of radiopharmaceuticals production process

Energy Technology Data Exchange (ETDEWEB)

Grecco, Claudio H.S.; Santos, Isaac J.A.L.; Carvalho, Paulo V.R., E-mail: grecco@ien.gov.b, E-mail: luquetti@ien.gov.b, E-mail: paulov@ien.gov.b [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Div. de Instrumentacao e Confiabilidade Humana; Vidal, Mario C.R., E-mail: mvidal@ergonomia.ufrj.b [Coordenacao dos Programas de Pos-Graduacao de Engenharia (PEP/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia de Producao. Grupo de Ergonomia e Novas Tecnologias (GENTE)

2011-07-01

Radiopharmaceuticals are radiation-emitting substances used in medicine for radiotherapy and imaging diagnosis. A Research Institute, located in Rio de Janeiro, produces three radiopharmaceuticals: the sodium iodate is used in the diagnosis of thyroid dysfunctions, the meta-iodo-benzyl guanidine is used in the diagnosis of cardiac diseases, and the fluorodeoxyglucose is used in diagnosis in cardiology, oncology, neurology and neuro psychiatry. This paper presents a leading safety performance indicators framework to assess the resilience of radiopharmaceuticals production processes. The organizations that use resilience indicators will be able to pro actively evaluate and manage safety. (author)

Sensitivity analysis of model output - a step towards robust safety indicators?

International Nuclear Information System (INIS)

Broed, R.; Pereira, A.; Moberg, L.

2004-01-01

The protection of the environment from ionising radiation challenges the radioecological community with the issue of harmonising disparate safety indicators. These indicators should preferably cover the whole spectrum of model predictions on chemo-toxic and radiation impact of contaminants. In question is not only the protection of man and biota but also of abiotic systems. In many cases modelling will constitute the basis for an evaluation of potential impact. It is recognised that uncertainty and sensitivity analysis of model output will play an important role in the 'construction' of safety indicators that are robust, reliable and easy to explain to all groups of stakeholders including the general public. However, environmental models of transport of radionuclides have some extreme characteristics. They are, a) complex, b) non-linear, c) include a huge number of input parameters, d) input parameters are associated with large or very large uncertainties, e) parameters are often correlated to each other, f) uncertainties other than parameter-driven may be present in the modelling system, g) space variability and time-dependence of parameters are present, h) model predictions may cover geological time scales. Consequently, uncertainty and sensitivity analysis are non-trivial tasks, challenging the decision-maker when it comes to the interpretation of safety indicators or the application of regulatory criteria. In this work we use the IAEA model ISAM, to make a set of Monte Carlo calculations. The ISAM model includes several nuclides and decay chains, many compartments and variable parameters covering the range of nuclide migration pathways from the near field to the biosphere. The goal of our calculations is to make a global sensitivity analysis. After extracting the non-influential parameters, the M.C. calculations are repeated with those parameters frozen. Reducing the number of parameters to a few ones will simplify the interpretation of the results and the use

Electronic health indicators in the selected countries: Are these indicators the best?

Science.gov (United States)

Afshari, Somaye; Khorasani, Elahe; Yarmohammadian, Mohammad Hossein; Atighechian, Golrokh; Darab, Mohsen Ghaffari

2013-01-01

Many changes have been made in different sciences by developing and advancing information and communication technology in last two decades. E-health is a very broad term that includes many different activities related to the use of electronic devices, software as well as hardware in health organizations. The aim of this study is comparing electronic health indicators in the selected countries and discussion on the best indicators. This study has chosen 12 countries randomly based on the regional division of the WHO. The relevant numbers of health indicators and general indicators and information technology indicators are extracted of these countries. We use data from the Bitarf's comparative study, which is conducted by the Iranian Supreme Council of Information Technology in 2007. By using Pearson correlation test, the relations between health general indicators and IT indicators are studied. Data was analyzed based on the research objectives using SPSS software and in accordance with research questions Pearson correlation test were used. The findings show that there is a positive relation between indicators related to IT and "Total per capita health, healthy life expectancy, percent literacy". Furthermore, there is a mutual relation between IT indicators and "mortality indicator". This study showed differences between selective indicators among different countries. The modern world, with its technological advances, is not powerless in the face of these geographic and health disparity challenges. Researchers must not rely on the available indicators. They must consider indicators like e-business companies, electronic data internet, medical supplies, health electronic record, health information system, etc., In future, continuous studies in this field, to provide the exact and regular reports of amount of using of these indicators through different countries must be necessary.

Study on the operational safety performance indicator of nuclear power plants in China

International Nuclear Information System (INIS)

Zhou Shirong

2005-01-01

The operational Safety Performance Indicator system (SPI) has been more and more regarded recently for their clear and effective characteristic in safety assessment for Nuclear Power Plants (NPPs). A large developing plan for NPPs construction is being discussed and considered in P.R. China. As one of important nuclear country, China expects to ensure the normal operation of NPPs and improve the safety level. National Nuclear Safety Administration (NNSA), National Nuclear Regulatory Agency of China, has put high attention on safety and SPI area, and many endeavours and attempts have been done or being carried out for an establishment of SPI system in China. NNSA intends to build an integrated SPI system to monitor all of the NPPs operation in China, based on the SPI system currently used in the world. NNSA believes that the SPI system will help to more effectively enforce the function of surveillance and management. The paper will introduces the status of study on the operational safety performance indicator of Nuclear Power Plants in China. (author)

What safety indicators for a storage in deep geologic deposit?

International Nuclear Information System (INIS)

Crouail, P.; Schneider, T.; Mure, J.M.; Voinis, S.

1999-01-01

Indicators must allow to discriminate and compare different options of facility conception and help the decision-makers in their choices. In the case of a deep storage, these indicators can also allow a comparison in terms of impact with other existing industrial systems (thermal or nuclear power plants, uranium ores) or even the natural radioactivity. Through Swedish and Canadian examples, the presentation makes an inventory of indicators that could be kept in a safety analysis of a deep storage. (N.C.)

Safety indicators used to prove the role of natural barrier for Saligny near surface disposal system

International Nuclear Information System (INIS)

Niculae, Ortenzia; Durdun, I.; Ionita, Gh.

2007-01-01

Full text: The siting process for a near surface repository suitable for the radioactive waste resulted from Cernavoda NPP operation and decommissioning (low level radioactive waste with small amounts of long lived radionuclides) started in 1992 and it included the collection of data from specific field and laboratory works for each site selection stage as well as different safety performance evaluation. According to the IAEA standards (Safety Guide No.111-G-3.1, 1994), the purpose of the siting process is not to get the best solution but to find out 'an acceptable solution, with sufficient safety reserves'. Since 1996, detailed field and investigation works were performed in Saligny preferred site including an experimental area to test the improvement method proposed for the foundation ground of repository, as well as detailed performance assessments using specific computer codes. The paper presents the results of recent performance assessments for the natural barrier of disposal system. The calculations were done using HYDRUS 2D, FEHM and AMBER computer codes. The endpoint of the Safety Report for Siting a Near Surface Repository at Saligny Site [CITON and SCN, Safety Report for Siting a Near Surface Repository at Saligny Site, 2007, pages 8.2.1-1 to 8.2.1-22 and 8-63 to 8-70] was the assessment of safety indicators. Individual annual effective dose for exposed peoples (both workers and general public) was the main safety indicator. In the same document, the radionuclide concentration in the disposal system compartments has been evaluated, as supplementary safety indicator of repository barriers (especially to confirm the natural barrier performance). The results confirmed the performance of natural barrier: the maximum extension of H-3 and Co-60 contaminant plume after repository closure remains more above underground water level. In the aquifer, iodine concentration reaches a value of 10 -15 mol/l, at the same magnitude order with the admitted limit from CFR

The value of safety indicators

NARCIS (Netherlands)

Kampen, J. van; Beek, B.D. van der; Groeneweg, J.

2013-01-01

Organisations are looking for ways to gain insight into the level of safety in their company so that additional measures can be taken when necessary and the effectiveness of interventions can be measured. That said, measuring safety, health and the environment is not easy. A survey among members of

The value of safety indicators

NARCIS (Netherlands)

Kampen, J. van; Beek, D. van der; Groeneweg, J.

2014-01-01

Organizations are searching for ways to gain insight into the level of safety in their company so that additional measures can be taken when necessary, and so the effectiveness of interventions can be measured. That said, measuring safety, health, and the environment is not easy. A survey among

The Role of Geographical Indication in Supporting Food Safety: A not Taken for Granted Nexus

Science.gov (United States)

2014-01-01

The paper focuses on the role of geographical indication in supporting strategies of food safety. Starting from the distinction between generic and specific quality, the article analyses the main factors influencing food safety in cases of geographical indication products, by stressing the importance of traceability systems and biodiversity in securing generic and specific quality. In the second part, the paper investigates the coordination problems behind a designation of origin and conditions to foster an effective collective action, a prerequisite to grant food safety through geographical indications. PMID:27800417

Selection of detailed items for periodic safety review on PWR radwaste management system

Energy Technology Data Exchange (ETDEWEB)

Sung, K. B.; Ahn, Y. S.; Park, Y. S.; Kim, S. H.; Kim, J. T. [Korea Hydric and Nuclear Power Company, Taejon (Korea, Republic of)

2003-10-01

Selection of detailed-items for Periodic Safety Review on PWR radwaste management system, the main component could be faithfully clarified according to the purpose of establishment on each system and basic purpose. It is proper to select detailed-items those of radioactivities in the reactor coolant activity levels and the released volume of liquid and gaseous radioactive material on safety performance. It's also proper to select solid radwaste production quantities as detailed-item that it would be predict the next ten years trends after PSR.

Selecting and applying indicators of ecosystem collapse for risk assessments.

Science.gov (United States)

Rowland, Jessica A; Nicholson, Emily; Murray, Nicholas J; Keith, David A; Lester, Rebecca E; Bland, Lucie M

2018-03-12

Ongoing ecosystem degradation and transformation are key threats to biodiversity. Measuring ecosystem change towards collapse relies on monitoring indicators that quantify key ecological processes. Yet little guidance is available on selecting and implementing indicators for ecosystem risk assessment. Here, we reviewed indicator use in ecological studies of decline towards collapse in marine pelagic and temperate forest ecosystems. We evaluated the use of indicator selection methods, indicator types (geographic distribution, abiotic, biotic), methods of assessing multiple indicators, and temporal quality of time series. We compared these ecological studies to risk assessments in the International Union for the Conservation of Nature Red List of Ecosystems (RLE), where indicators are used to estimate ecosystem collapse risk. We found that ecological studies and RLE assessments rarely reported how indicators were selected, particularly in terrestrial ecosystems. Few ecological studies and RLE assessments quantified ecosystem change with all three indicator types, and indicators types used varied between marine and terrestrial ecosystem. Several studies used indices or multivariate analyses to assess multiple indicators simultaneously, but RLE assessments did not, as RLE guidelines advise against them. Most studies and RLE assessments used time series spanning at least 30 years, increasing the chance of reliably detecting change. Limited use of indicator selection protocols and infrequent use of all three indicator types may hamper the ability to accurately detect changes. To improve the value of risk assessments for informing policy and management, we recommend using: (i) explicit protocols, including conceptual models, to identify and select indicators; (ii) a range of indicators spanning distributional, abiotic and biotic features; (iii) indices and multivariate analyses with extreme care until guidelines are developed; (iv) time series with sufficient data to

AN ANALYSIS OF ACCIDENT TRENDS AND MODELING OF SAFETY INDICES IN AN INDIAN CONSTRUCTION ORGANIZATION

Directory of Open Access Journals (Sweden)

Sunku Venkata Siva Rajaprasad

2016-09-01

Full Text Available Construction industry has been recognized as a hazardous industry in many countries due to distinct nature of execution of works.The accident rate in construction sector is high all over the world due to dynamic nature of work activities. Occurrence of accidents and its severity in construction industry is several times higher than the manufacturing industries. The study was limited to a major construction organization in India to examine the trends in construction accidents for the period 2008-2014. In India, safety performance is gauged basing on safety indices; frequency, severity and incidence rates. It is not practicable to take decisions or to implement safety strategies on the basis of indices. The data used for this study was collected from a leading construction organization involved in execution of major construction activities all over India and abroad. The multiple regression method was adopted to model the pattern of safety indices wise .The pattern showed that significant relationships exist between the three safety indices and the related independent variables.

Road safety performance indicators for the interurban road network.

Science.gov (United States)

Yannis, George; Weijermars, Wendy; Gitelman, Victoria; Vis, Martijn; Chaziris, Antonis; Papadimitriou, Eleonora; Azevedo, Carlos Lima

2013-11-01

Various road safety performance indicators (SPIs) have been proposed for different road safety research areas, mainly as regards driver behaviour (e.g. seat belt use, alcohol, drugs, etc.) and vehicles (e.g. passive safety); however, no SPIs for the road network and design have been developed. The objective of this research is the development of an SPI for the road network, to be used as a benchmark for cross-region comparisons. The developed SPI essentially makes a comparison of the existing road network to the theoretically required one, defined as one which meets some minimum requirements with respect to road safety. This paper presents a theoretical concept for the determination of this SPI as well as a translation of this theory into a practical method. Also, the method is applied in a number of pilot countries namely the Netherlands, Portugal, Greece and Israel. The results show that the SPI could be efficiently calculated in all countries, despite some differences in the data sources. In general, the calculated overall SPI scores were realistic and ranged from 81 to 94%, with the exception of Greece where the SPI was relatively lower (67%). However, the SPI should be considered as a first attempt to determine the safety level of the road network. The proposed method has some limitations and could be further improved. The paper presents directions for further research to further develop the SPI. Copyright © 2012 Elsevier Ltd. All rights reserved.

Selecting Social Indicators to Forecast Child Welfare Caseload

Directory of Open Access Journals (Sweden)

Raghubar D. Sharma

2008-12-01

identified social indicators that were statistically associated with the risk factors. After measuring the statistical association between social indictors with child welfare caseload, this study develops regression models to select and narrow down a list of social indicators with the highest predictability.

Selection indices for yield and quality traits in sweet corn

International Nuclear Information System (INIS)

Asghar, M.J.; Mehdi, S.S.

2010-01-01

The efficiency of three selection indices, viz., Smith-Hazel index (SHI), Desired gain index (DGI) and Base Index (BI) was compared for the improvement of an open pollinated sweet corn (Zea mays L. Saccharata) population. The data of genetic studies on various yield and quality traits among S1 families were used to construct these selection indices. Smith-Hazel index was found to be the most efficient in improving the aggregate genotype of yield traits for most of the selection strategies. Base index proved to be more efficient as compared to Smith-Hazel index in the improvement of aggregate genotype for five out of six selection strategies of quality traits. Both smith-hazel and Base indices were found useful for the improvement of sweetness and sweet flavour for all the selection strategies. When selection was confined to eight yield and four quality traits simultaneously, Base index proved to be more efficient as compared to Smith-Hazel index and desired gain index in improving the aggregate genotype for almost all the selection strategies. (author)

Safety approach to the selection of design criteria for the CRBRP reactor refueling system

International Nuclear Information System (INIS)

Meisl, C.J.; Berg, G.E.; Sharkey, N.F.

1979-01-01

The selection of safety design criteria for Liquid Metal Fast Breeder Reactor (LMFBR) refueling systems required the extrapolation of regulations and guidelines intended for Light Water Reactor refueling systems and was encumbered by the lack of benefit from a commercially licensed predecessor other than Fermi. The overall approach and underlying logic are described for developing safety design criteria for the reactor refueling system (RRS) of the Clinch River Breeder Reactor Plant (CRBRP). The complete selection process used to establish the criteria is presented, from the definition of safety functions to the finalization of safety design criteria in the appropriate documents. The process steps are illustrated by examples

The effect of Health, Safety and Environment Management System (HSE-MS on the improvement of safety performance indices in Urea and Ammonia Kermanshah Petrochemical Company

Directory of Open Access Journals (Sweden)

M. S. Poursoleiman

2015-09-01

Full Text Available Introduction: Work-related accidents may cause damage to people, environment and lead to waste of time and money. Health, Safety and Environment Management System has been developed in order to reduce accidents. This study aimed to investigate the effect of implementation of this system on reduction of the accidents and its consequences and also on the safety performance indices in Kermanshah Petrochemical Company. Material and Method: In this study, records of accidents were collected by OSHA incident report form 301 over 4 years. Following, the mean annual accidents and its consequences and safety performance indices were calculated and reported. Then, using statistical analysis, the impacts of two years implementation of this system on the accidents and its consequences and safety performance indices were evaluated. Result: The results showed that the implementation of HSE system was significantly correlated with Frequency Severity Indicator, Accident Severity Rate, lost days, minor accidents and total incidents (P-value 0.05. Conclusion: The implementation of Health, Safety and the Environment Management System caused a reduction in accidents and its consequences and most of the safety performance indices in the entire process cycle of Kermanshah Petrochemical Company. Overall, safety condition has been improved considerably.

Hamilton's indicators of the force of selection

DEFF Research Database (Denmark)

Baudisch, Annette

2005-01-01

To quantify the force of selection, Hamilton [Hamilton, W. D. (1966) J. Theor. Biol. 12, 12-45] derived expressions for the change in fitness with respect to age-specific mutations. Hamilton's indicators are decreasing functions of age. He concluded that senescence is inevitable: survival...... and fertility decline with age. I show that alternative parameterizations of mutational effects lead to indicators that can increase with age. I then consider the case of deleterious mutations with age-specific effects. In this case, it is the balance between mutation and selection pressure that determines...... the equilibrium number of mutations in a population. In this balance, the effects of different parameterizations cancel out, but only to a linear approximation. I show that mutation accumulation has little impact at ages when this linear approximation holds. When mutation accumulation matters, nonlinear effects...

Selection of relevant dietary indicators for health.

Science.gov (United States)

Steingrímsdóttir, L; Ovesen, L; Moreiras, O; Jacob, S

2002-05-01

To define a set of dietary components that are relevant determinants for health in Europe. The selected components are intended to serve as nutrition indicators for health in the European Health Monitoring Programme and, as such, must be limited in number, relevant to health in Europe and practical for all involved countries with respect to data gathering and comparability of data. Major nutrition factors were determined by reviewing relevant epidemiological and clinical literature in nutrition and health as well as referring to reports from international expert groups, including the report from the project Nutrition and Diet for Healthy Lifestyles in Europe. The selection of factors was also based on the relative ease and cost involved for participating countries to obtain comparable and valid data. The selected factors include foods or food groups as well as individual nutrients. Biomarkers are suggested for selected nutrients that pose the greatest difficulty in obtaining valid and comparable data from dietary studies. The following list of diet indicators for health monitoring in Europe was agreed upon by the EFCOSUM group in 2001, in order of priority: vegetables, fruit, bread, fish, saturated fatty acids as percentage of energy (%E), total fat as %E, and ethanol in grams per day. Biomarkers were suggested for the following nutrients: folate, vitamin D, iron, iodine and sodium. Energy has to be assessed in order to calculate %E from total fat and saturated fatty acids.

Selecting safety standards for nuclear power plants

International Nuclear Information System (INIS)

1981-01-01

Today, many thousands of documents are available describing the requirements, guidelines, and industrial standards which can be used as bases for a nuclear power plant programme. Many of these documents relate to nuclear safety which is currently the focus of world-wide attention. The multitude of documents available on the subject, and their varying status and emphasis, make the processes of selection and implementation very important. Because nuclear power plants are technically intricate and advanced, particularly in relation to the technological status of many developing countries, these processes are also complicated. These matters were the subject of a seminar held at the Agency's headquarters in Vienna last December. The IAEA Nuclear Safety Standards (NUSS) programme was outlined and explained at the Seminar. The five areas of the NUSS programme for nuclear power plants cover, governmental organization, siting, design; operation; quality assurance. In each area the Agency has issued Codes of Practice and is developing Safety Guides. These provide regulatory agencies with a framework for safety. The Seminar recognized that the NUSS programme should enable developing countries to identify priorities in their work, particularly the implementation of safety standards. The ISO activities in the nuclear field are carried out in the framework of its Technical Committee 85 (ISO/TC85). The work is distributed in sub-committees. Seminar on selection and implementation of safety standards for nuclear power plants, jointly organized by the IAEA and the International Organization for Standardization (ISO), and held in Vienna from 15 to 18 December 1980 concerned with: terminology, definitions, units and symbols (SC-1), radiation protection (SC-2), power reactor technology (SC-3), nuclear fuel technology (SC-5). There was general agreement that the ISO standards are complementary to the NUSS codes and guides. ISO has had close relations with the IAEA for several years

Attitude of the Korean dentists towards radiation safety and selection criteria

International Nuclear Information System (INIS)

Lee, Byung Do; Ludlow, John B.

2013-01-01

X-ray exposure should be clinically justified and each exposure should be expected to give patients benefits. Since dental radiographic examination is one of the most frequent radiological procedures, radiation hazard becomes an important public health concern. The purpose of this study was to investigate the attitude of Korean dentists about radiation safety and use of criteria for selecting the frequency and type of radiographic examinations. The study included 267 Korean dentists. Five questions related to radiation safety were asked of each of them. These questions were about factors associated with radiation protection of patients and operators including the use of radiographic selection criteria for intraoral radiographic procedures. The frequency of prescription of routine radiographic examination (an example is a panoramic radiograph for screening process for occult disease) was 34.1%, while that of selective radiography was 64.0%. Dentists' discussion of radiation risk and benefit with patients was infrequent. More than half of the operators held the image receptor by themselves during intraoral radiographic examinations. Lead apron/thyroid collars for patient protection were used by fewer than 22% of dental offices. Rectangular collimation was utilized by fewer than 15% of dental offices. The majority of Korean dentists in the study did not practice radiation protection procedures which would be required to minimize exposure to unnecessary radiation for patients and dental professionals. Mandatory continuing professional education in radiation safety and development of Korean radiographic selection criteria is recommended.

Attitude of the Korean dentists towards radiation safety and selection criteria

Energy Technology Data Exchange (ETDEWEB)

Lee, Byung Do [Dept. of Oral and Maxillofacial Radiology and Wonkwang Dental Research Institute, College of Dentistry, Wonkwang University, Iksan (Korea, Republic of); Ludlow, John B. [Graduate Program in Oral and Maxillofacial Radiology, School of Dentistry, University of North Carolina, Chapel Hill (United States)

2013-09-15

X-ray exposure should be clinically justified and each exposure should be expected to give patients benefits. Since dental radiographic examination is one of the most frequent radiological procedures, radiation hazard becomes an important public health concern. The purpose of this study was to investigate the attitude of Korean dentists about radiation safety and use of criteria for selecting the frequency and type of radiographic examinations. The study included 267 Korean dentists. Five questions related to radiation safety were asked of each of them. These questions were about factors associated with radiation protection of patients and operators including the use of radiographic selection criteria for intraoral radiographic procedures. The frequency of prescription of routine radiographic examination (an example is a panoramic radiograph for screening process for occult disease) was 34.1%, while that of selective radiography was 64.0%. Dentists' discussion of radiation risk and benefit with patients was infrequent. More than half of the operators held the image receptor by themselves during intraoral radiographic examinations. Lead apron/thyroid collars for patient protection were used by fewer than 22% of dental offices. Rectangular collimation was utilized by fewer than 15% of dental offices. The majority of Korean dentists in the study did not practice radiation protection procedures which would be required to minimize exposure to unnecessary radiation for patients and dental professionals. Mandatory continuing professional education in radiation safety and development of Korean radiographic selection criteria is recommended.

78 FR 15920 - Federal Motor Vehicle Safety Standards; Tire Selection and Rims

Science.gov (United States)

2013-03-13

... [Docket No. NHTSA-2013-0030] RIN 2127-AL24 Federal Motor Vehicle Safety Standards; Tire Selection and Rims... Safety Standard (FMVSS) No. 110 to make it clear that special trailer (ST) tires are permitted to be... also proposes to exclude these trailers from a vehicle testing requirement that a tire must be retained...

Safety assessment input for site selection - the Swedish example - 59031

International Nuclear Information System (INIS)

Andersson, Johan

2012-01-01

Svensk Kaernbraenslehantering AB (SKB) has performed comprehensive investigations of two candidate sites for a final repository for Sweden's spent nuclear fuel. In March 2011 SKB decided to submit licence applications for a final repository at Forsmark. Before selection, SKB stated that the site that offers the best prospects for achieving long-term safety in practice would be selected. Based on experiences previous safety assessments, a number of issues related to long-term safety need to be considered in the context of site comparison. The factors include sensitivity to climate change such as periods of permafrost and glaciations, rock mechanics evolution including the potential for thermally induced spalling and sensitivity to potential future earthquakes, current and future groundwater flow, evolution of groundwater composition and proximity to mineral resources. Each of these factors related to long-term safety for the two candidate sites is assessed in a comparative analysis of site characteristics. The assessment also considers differences in biosphere conditions and in the confidence of the site descriptions. The comparison is concluded by an assessment on how the identified differences would affect the estimated radiological risk from a repository located at either of the sites. The assessment concludes that there are a number of safety related site characteristics for which the analyses do not show any decisive differences in terms of implications on safety, between the sites Forsmark and Laxemar. However, the frequency of water conducting fractures at repository depth is much smaller at Forsmark than at Laxemar. This difference, in turn, affects the future stability of the current favourable groundwater composition, which combined with the much higher flows at Laxemar would, for the current repository design, lead to a breach in the safety functions for the buffer and the canister for many more deposition positions at Laxemar than at Forsmark. Thereby

Safety indicators adopted in the Finnish regulations for long-term safety of spent fuel disposal

International Nuclear Information System (INIS)

Ruokola, E.

2002-01-01

A regulatory guide for the safety of spent fuel disposal has recently been issued to guide the implementer's programme in the preconstruction phase. The guide is based on dose criteria in the time frame, which is reasonably predictable with respect to assessment of human exposure. For the time frame that involves major climate changes such as permafrost and glaciation, the guide defines constraints for the activity releases to the environment. This paper discusses the rationale for the selected approach and the derivation of the activity release constraints. (author)

VSRR - Quarterly provisional estimates for selected birth indicators

Data.gov (United States)

U.S. Department of Health & Human Services — Provisional estimates of selected reproductive indicators. Estimates are presented for: general fertility rates, age-specific birth rates, total and low risk...

Selecting clinical quality indicators for laboratory medicine.

Science.gov (United States)

Barth, Julian H

2012-05-01

Quality in laboratory medicine is often described as doing the right test at the right time for the right person. Laboratory processes currently operate under the oversight of an accreditation body which gives confidence that the process is good. However, there are aspects of quality that are not measured by these processes. These are largely focused on ensuring that the most clinically appropriate test is performed and interpreted correctly. Clinical quality indicators were selected through a two-phase process. Firstly, a series of focus groups of clinical scientists were held with the aim of developing a list of quality indicators. These were subsequently ranked in order by an expert panel of primary and secondary care physicians. The 10 top indicators included the communication of critical results, comprehensive education to all users and adequate quality assurance for point-of-care testing. Laboratories should ensure their tests are used to national standards, that they have clinical utility, are calibrated to national standards and have long-term stability for chronic disease management. Laboratories should have error logs and demonstrate evidence of measures introduced to reduce chances of similar future errors. Laboratories should make a formal scientific evaluation of analytical quality. This paper describes the process of selection of quality indicators for laboratory medicine that have been validated sequentially by deliverers and users of the service. They now need to be converted into measureable variables related to outcome and validated in practice.

Patient safety in a service of medical physics. Key indicators

International Nuclear Information System (INIS)

Font Gomez, J. A.; Gandia Martinez, A.; Jimenez Albericio, F. J.; Andres Redondo, M. M.; Mengual Gil, M. A.

2013-01-01

The key indicators are those that endure over time to monitor the degree of compliance with the criteria in the processes that are considered key in the service. In the case of our service, define key indicators within the framework of ISO 9001 certification in the process of clinical dosimetry. All problems do not have same casuistry or not, have the same detrimental to the safety of the patient. We have prioritized some of the problems and opportunities for improvement have been found. Standard refers to the value of the indicator that we should or would like to achieve in such a way that if not achieved, action of improvement will be required. (Author)

Main indicators used in french PWR units for safety, operation and maintenance

International Nuclear Information System (INIS)

Guio, J.M. de

1990-01-01

The development of analyses aimed at improving nuclear plant operations through an optimum use of experience feedback naturally leads to the implementation of trend indicators in the fields of safety, operation and maintenance. This process, part of the more general framework of promoting safety culture, facilitates collective thinking on these matters at the local site level, and, at the national level, allows a clearer definition of the main lines of strategy and helps coordinate the resulting actions

Safety update on the use of recombinant activated factor VII in approved indications.

Science.gov (United States)

Neufeld, Ellis J; Négrier, Claude; Arkhammar, Per; Benchikh el Fegoun, Soraya; Simonsen, Mette Duelund; Rosholm, Anders; Seremetis, Stephanie

2015-06-01

This updated safety review summarises the large body of safety data available on the use of recombinant activated factor VII (rFVIIa) in approved indications: haemophilia with inhibitors, congenital factor VII (FVII) deficiency, acquired haemophilia and Glanzmann's thrombasthenia. Accumulated data up to 31 December 2013 from clinical trials as well as post-marketing data (registries, literature reports and spontaneous reports) were included. Overall, rFVIIa has shown a consistently favourable safety profile, with no unexpected safety concerns, in all approved indications. No confirmed cases of neutralising antibodies against rFVIIa have been reported in patients with congenital haemophilia, acquired haemophilia or Glanzmann's thrombasthenia. The favourable safety profile of rFVIIa can be attributed to the recombinant nature of rFVIIa and its localised mechanism of action at the site of vascular injury. Recombinant FVIIa activates factor X directly on the surface of activated platelets, which are present only at the site of injury, meaning that systemic activation of coagulation is avoided and the risk of thrombotic events (TEs) thus reduced. Nonetheless, close monitoring for signs and symptoms of TE is warranted in all patients treated with any pro-haemostatic agent, including rFVIIa, especially the elderly and any other patients with concomitant conditions and/or predisposing risk factors to thrombosis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Selection and Use of Performance Indicators in Decommissioning

International Nuclear Information System (INIS)

2011-01-01

The success of completing a decommissioning project on schedule and budget is determined by the ability to define a clear endpoint (outcome), to accurately determine intermediate progress, and develop reliable forecasts to complete remaining tasks. Performance indicators are used to examine those aspects that are crucial to this success. This information is required by and periodically reported to various stakeholders. Although the practice of nuclear decommissioning is maturing, it would benefit from optimal use of performance indicators. Performance measurement is the 'heart and soul' of the performance based management process. Flowing from the organizational mission and the strategic planning process, it provides the data that will be collected, analysed, reported and ultimately, used to make sound business decisions. It directs the business function by documenting progress towards established objectives, identifying areas of both strength and weakness, and justifying budgetary expenditures. In this report, practical advice is provided on the effective use of performance indicators to measure and report on the achievement of the goals and plans of a nuclear decommissioning project. The structure of the report takes the reader progressively through all aspects of designing, selecting and using performance indicators. A process for setting up a performance indicator system against basic principles is presented, including a discussion of each step in the process. The report also provides an expanded discussion of the most important influences on the identification and selection of performance indicators. Finally, practical guidance on the use of performance indicators in specific Member States is provided together with field experience.

A novel safety assessment strategy applied to non-selective extracts.

Science.gov (United States)

Koster, Sander; Leeman, Winfried; Verheij, Elwin; Dutman, Ellen; van Stee, Leo; Nielsen, Lene Munch; Ronsmans, Stefan; Noteborn, Hub; Krul, Lisette

2015-06-01

A main challenge in food safety research is to demonstrate that processing of foodstuffs does not lead to the formation of substances for which the safety upon consumption might be questioned. This is especially so since food is a complex matrix in which the analytical detection of substances, and consequent risk assessment thereof, is difficult to determine. Here, a pragmatic novel safety assessment strategy is applied to the production of non-selective extracts (NSEs), used for different purposes in food such as for colouring purposes, which are complex food mixtures prepared from reference juices. The Complex Mixture Safety Assessment Strategy (CoMSAS) is an exposure driven approach enabling to efficiently assess the safety of the NSE by focussing on newly formed substances or substances that may increase in exposure during the processing of the NSE. CoMSAS enables to distinguish toxicologically relevant from toxicologically less relevant substances, when related to their respective levels of exposure. This will reduce the amount of work needed for identification, characterisation and safety assessment of unknown substances detected at low concentration, without the need for toxicity testing using animal studies. In this paper, the CoMSAS approach has been applied for elderberry and pumpkin NSEs used for food colouring purposes. Copyright © 2015 Elsevier Ltd. All rights reserved.

On the selection of Secondary Indices in Relational Databases

NARCIS (Netherlands)

Choenni, R.S.; Blanken, Henk; Chang, Thiel

1993-01-01

An important problem in the physical design of databases is the selection of secondary indices. In general, this problem cannot be solved in an optimal way due to the complexity of the selection process. Often use is made of heuristics such as the well-known ADD and DROP algorithms. In this paper it

One safety critical indicators model for regulatory actions on nuclear power plants based on a level 1 PSA; Um modelo de indicadores criticos de seguranca para acoes regulatorias em usinas nucleares baseado em uma APS nivel 1

Energy Technology Data Exchange (ETDEWEB)

Araujo, Jefferson Borges

2006-03-15

This study presents a general methodology to the establishment, selection and use of safety indicators for a two loop PWR plant, as Angra 1. The study performed identifies areas considered critical for the plant operational safety. For each of these areas, strategic sub-areas are defined. For each strategic sub-area, specific safety indicators are defined. These proposed Safety Indicators are based on the contribution to risk considering a quantitative risk analysis. For each safety indicator, a goal, a bounded interval and proper bases are developed, to allow for a clear and comprehensive individual behavior evaluation. Additionally, an integrated evaluation of the indicators, using expert systems, was done to obtain an overview of the plant general safety. This methodology can be used for identifying situations where the plant safety is challenged, by giving a general overview of the plant operational condition. Additionally, this study can also identify eventual room for improvements by generating suggestions and recommendations, as a complement for regulatory actions and inspections, focusing resources on eventual existing weaknesses, in order to increase or maintain a high pattern of operational safety. (author)

Inclusion of social indicators in decision support tools for the selection of sustainable site remediation options.

Science.gov (United States)

Cappuyns, Valérie

2016-12-15

Sustainable remediation requires a balanced decision-making process in which environmental, economic and social aspects of different remediation options are all considered together and the optimum remediation solution is selected. More attention has been paid to the evaluation of environmental and economic aspects, in particular to reduce the human and environmental risks and the remediation costs, to the exclusion of social aspects of remediation. This paper investigates how social aspects are currently considered in sustainability assessments of remediation projects. A selection of decision support tools (DSTs), used for the sustainability assessment of a remediation project, is analyzed to define how social aspects are considered in those tools. The social indicator categories of the Sustainable Remediation Forum - United Kingdom (SuRF-UK), are used as a basis for this evaluation. The consideration of social aspects in the investigated decision support tools is limited, but a clear increase is noticed in more recently developed tools. Among the five social indicator categories defined by SuRF-UK to facilitate a holistic consideration of social aspects of a remediation project only "Human health and safety" is systematically taken into account. "Neighbourhood and locality" is also often addressed, mostly emphasizing the potential disturbance caused by the remediation activities. However, the evaluation of 'Ethics and Equality', Communities and community involvement', and 'Uncertainty and evidence' is often neglected. Nevertheless, concrete examples can be found in some of the investigated tools. Specific legislation, standard procedures, and guidelines that have to be followed in a region or country are mainly been set up in the context of protecting human and ecosystem health, safety and prevention of nuisance. However, they sometimes already include some of the aspects addressed by the social indicators. In this perspective the use of DST to evaluate the

Exposure data and risk indicators for safety performance assessment in Europe.

NARCIS (Netherlands)

Papadimitriou, E. Yannis, G. Bijleveld, F.D. & Cardoso, J.L.

2013-01-01

The objective of this paper is the analysis of the state-of-the-art in risk indicators and exposure data for safety performance assessment in Europe, in terms of data availability, collection methodologies and use. More specifically, the concepts of exposure and risk are explored, as well as the

Selecting a Regression Saturated by Indicators

DEFF Research Database (Denmark)

Hendry, David F.; Johansen, Søren; Santos, Carlos

We consider selecting a regression model, using a variant of Gets, when there are more variables than observations, in the special case that the variables are impulse dummies (indicators) for every observation. We show that the setting is unproblematic if tackled appropriately, and obtain the fin...... the finite-sample distribution of estimators of the mean and variance in a simple location-scale model under the null that no impulses matter. A Monte Carlo simulation confirms the null distribution, and shows power against an alternative of interest....

Selecting a Regression Saturated by Indicators

DEFF Research Database (Denmark)

Hendry, David F.; Johansen, Søren; Santos, Carlos

We consider selecting a regression model, using a variant of Gets, when there are more variables than observations, in the special case that the variables are impulse dummies (indicators) for every observation. We show that the setting is unproblematic if tackled appropriately, and obtain the fin...... the finite-sample distribution of estimators of the mean and variance in a simple location-scale model under the null that no impulses matter. A Monte Carlo simulation confirms the null distribution, and shows power against an alternative of interest...

Research on the Evaluation System for Rural Public Safety Planning

Institute of Scientific and Technical Information of China (English)

Ming; SUN; Jianxin; YAN

2014-01-01

The indicator evaluation system is introduced to the study of rural public safety planning in this article.By researching the current rural public safety planning and environmental carrying capacity,we select some carrying capacity indicators influencing the rural public safety,such as land,population,ecological environment,water resources,infrastructure,economy and society,to establish the environmental carrying capacity indicator system.We standardize the indicators,use gray correlation analysis method to determine the weight of indicators,and make DEA evaluation of the indicator system,to obtain the evaluation results as the basis for decision making in rural safety planning,and provide scientific and quantified technical support for rural public safety planning.

Evaluation of Selection Indices for Alfalfa (Medicago sativa L.

Directory of Open Access Journals (Sweden)

Hassan MONIRIFAR

2010-03-01

Full Text Available In order to evaluate the efficiency of selection indices in alfalfa improvement, an experiment was conducted from 2000 to 2007 at East Azarbaijan Agricultural and Natural Resources Research Center, Iran. A set of 29 native ecotypes, which were collected in 2000 and 2001 from Azerbaijan (Iran, together with one improved variety were used to conduct a polycross nursery. For the purpose of random mating, a randomized complete block design was used with 12 replications arranged in this nursery. The resulting 30 half-sib families were planted individually in pots and the 30 days old seedlings were transplanted to the field in May, 2004. Each 3-row plot consisted of 45 HS plants. Several traits, such as individual plants� fresh weight and individual plants� dry weight (IPFW, IPDW, number of shoots per plant (NS and plant height (PH in each harvest and also, days until 10% flowering, the ratio of fresh and dry weight of leaves/plant and size of trifoliate leaves were measured for three cropping seasons. The results of analysis of variance showed large variation among polycross progenies. Six selection indices (Ii with different number of traits at adult plant stage were evaluated. Based on the result of this investigation, if number of shoots and height of adult plant, excluding yield, are recorded, I2 is suggested. If, in addition to fresh yield, height of adult plant is measured, I6 is recommended. I4 is useful when number of shoots and plant height with dry yield are included in the index. In conclusion, the importance of mature plant traits in selection indices was in the order of yield > plant height > number of shoots. The results provided more evidence that selection indices incorporating the component of dry yield are more advantageous. The most efficient selection index consisted of NS, IPDW and PH, having a relative efficiency of 280%.

Key Performance Indicators in the Evaluation of the Quality of Radiation Safety Programs.

Science.gov (United States)

Schultz, Cheryl Culver; Shaffer, Sheila; Fink-Bennett, Darlene; Winokur, Kay

2016-08-01

Beaumont is a multiple hospital health care system with a centralized radiation safety department. The health system operates under a broad scope Nuclear Regulatory Commission license but also maintains several other limited use NRC licenses in off-site facilities and clinics. The hospital-based program is expansive including diagnostic radiology and nuclear medicine (molecular imaging), interventional radiology, a comprehensive cardiovascular program, multiple forms of radiation therapy (low dose rate brachytherapy, high dose rate brachytherapy, external beam radiotherapy, and gamma knife), and the Research Institute (including basic bench top, human and animal). Each year, in the annual report, data is analyzed and then tracked and trended. While any summary report will, by nature, include items such as the number of pieces of equipment, inspections performed, staff monitored and educated and other similar parameters, not all include an objective review of the quality and effectiveness of the program. Through objective numerical data Beaumont adopted seven key performance indicators. The assertion made is that key performance indicators can be used to establish benchmarks for evaluation and comparison of the effectiveness and quality of radiation safety programs. Based on over a decade of data collection, and adoption of key performance indicators, this paper demonstrates one way to establish objective benchmarking for radiation safety programs in the health care environment.

The effect of Health, Safety and Environment Management System (HSE-MS on the improvement of safety performance indices in Urea and Ammonia Kermanshah Petrochemical Company

Directory of Open Access Journals (Sweden)

M. S. Poursoleiman

2015-09-01

.Conclusion: The implementation of Health, Safety and the Environment Management System caused a reduction in accidents and its consequences and most of the safety performance indices in the entire process cycle of Kermanshah Petrochemical Company. Overall, safety condition has been improved considerably.

Safety assesment necessary in selecting the technologies for partial decommissioning of nuclear facilities. Application to research reactors

International Nuclear Information System (INIS)

Niculae, O.; Stan, C.; Vladescu, G.

2005-01-01

The main goal of this work is identification and evaluation of safety indicators - quantities used in monitoring the safety assurance during decommissioning processes in nuclear facilities identification of safety indicators is made on basis of qualitative and quantitative analysis, effected for both normal decommissioning, as well as in case of foreseen event occurrence. The safety indicators form an integrated system which can be represented by a pyramidal structural with the following levels (in increasing complexity order): specific indicators, strategic indicators, overall indicators, safety closure. This work suggests that evaluation of safety assurance level during the conduct of a decommissioning process to be based on the overall analysis of the set of indicators emphasizing not only the evaluation of individual safety indicators but also the interdependencies between them. The evaluation method is based on the 'step-by-step' principle. The evaluation was carried-out either directly or by means of dedicated evaluation forms which cover both quantitative and qualitative aspects of the analysis. At the some time identified are the adequate protection measures for the personnel implied in decommissioning, as well as for population and environment. The paper present also technologies adequate in the decommissioning. (authors)

Indicators of the management for the continuous improvement of the radiological safety in a radioactive facility

International Nuclear Information System (INIS)

Amador B, Z. H.

2006-01-01

The use of safety indicators is common in the nuclear industry. In this work the implementation of indicators for the efficiency analysis of the radiological safety management system of a radioactive installation is presented. Through the same ones the occupational exposure, the training Y authorization of the personnel, the control of practices Y radioactive inventory, the results of the radiological surveillance, the occurrence of radiological events, the aptitude of the monitoring equipment, the management of the radioactive waste, the public exposure, the audits Y the costs of safety are evaluated. Its study is included in the periodic training of the workers. Without this interrelation it is not possible to maintain the optimization of the safety neither to achieve a continuous improvement. (Author)

The relative value of safety and performance indicators and qualitative arguments in different time frames

International Nuclear Information System (INIS)

Alonso, J.; Rohlig, K.J.; Batandjieva, B.; Griffault, L.; Regent, A.; Schneider, J.; Storck, R.; Umeki, H.

2002-01-01

Indicators complementary to dose or risk are of great importance for the provision of multiple lines of reasoning at different time frames and therefore for the building of confidence within a safety case and that regulations should acknowledge this fact. They are also of great value with regard to the understanding of the safety case by and the communication to different audiences. The relative value of such indicators changes with time. For longer timescales qualitative information becomes more important. The meaning of calculated dose or risk is different for different timescales (ranging from expected performance to illustration) but dose or risk remains a valuable and central information for any time considered in a Safety Assessment. Certain indicators (concentrations and fluxes) can provide information by avoiding certain uncertainties which increase remarkably with time (biosphere, dilution) but apart from that no generic opinion or recommendation can be derived since the value of specific indicators and the required degree of aggregation (over different nuclides or even of consequence and probability) strongly depends on the many parameter. (authors)

Canadian Association of Gastroenterology consensus guidelines on safety and quality indicators in endoscopy.

Science.gov (United States)

Armstrong, David; Barkun, Alan; Bridges, Ron; Carter, Rose; de Gara, Chris; Dube, Catherine; Enns, Robert; Hollingworth, Roger; Macintosh, Donald; Borgaonkar, Mark; Forget, Sylviane; Leontiadis, Grigorios; Meddings, Jonathan; Cotton, Peter; Kuipers, Ernst J

2012-01-01

Increasing use of gastrointestinal endoscopy, particularly for colorectal cancer screening, and increasing emphasis on health care quality, highlight the need for clearly defined, evidence-based processes to support quality improvement in endoscopy. To identify processes and indicators of quality and safety relevant to high-quality endoscopy service delivery. A multidisciplinary group of 35 voting participants developed recommendation statements and performance indicators. Systematic literature searches generated 50 initial statements that were revised iteratively following a modified Delphi approach using a web-based evaluation and voting tool. Statement development and evidence evaluation followed the AGREE (Appraisal of Guidelines, REsearch and Evaluation) and GRADE (Grading of Recommendations, Assessment, Development and Evaluation) guidelines. At the consensus conference, participants voted anonymously on all statements using a 6-point scale. Subsequent web-based voting evaluated recommendations for specific, individual quality indicators, safety indicators and mandatory endoscopy reporting fields. Consensus was defined a priori as agreement by 80% of participants. Consensus was reached on 23 recommendation statements addressing the following: ethics (statement 1: agreement 100%), facility standards and policies (statements 2 to 9: 90% to 100%), quality assurance (statements 10 to 13: 94% to 100%), training, education, competency and privileges (statements 14 to 19: 97% to 100%), endoscopy reporting standards (statements 20 and 21: 97% to 100%) and patient perceptions (statements 22 and 23: 100%). Additionally, 18 quality indicators (agreement 83% to 100%), 20 safety indicators (agreement 77% to 100%) and 23 recommended endoscopy-reporting elements (agreement 91% to 100%) were identified. The consensus process identified a clear need for high-quality clinical and outcomes research to support quality improvement in the delivery of endoscopy services. The

Summary report on the use of plant safety performance indicators

International Nuclear Information System (INIS)

2001-09-01

In 1998, the OECD/NEA committee on Nuclear Regulatory Activities (CNRA) initiated an activity with the objective of advancing the discussion on how to enhance and measure regulatory effectiveness in relation to nuclear installations. One of the outcome of this activity was to establish a Task group to develop internal (direct) performance indicators which would be used to monitor regulatory efficiency. In parallel, a joint CNRA/CSNI group was launched in December 2000 to exchange information and develop external (indirect) indicators to measure regulatory effectiveness, i.e. impact on licensee's safety performance. These external indicators are, in other words, the traditional plant performance indicators (PI's) and these are the ones that this report deals with. This report presents the work performed by the joint CNRA/CSNI task group mentioned above. It provides a summary of the sets of PI's being used by different regulatory bodies and WANO, it describes the national practices on the use of PI's and proposes a set of PI's that could be used nationally describing regulatory effectiveness and also as a basis for an international system. The task force consisted of regulators, organisations which have a performance indicators system in operation or under testing. The task force met in Paris on February 19-20, 2001. Each participant provided a brief description of the PI System at his organisation and its usage. The group identified a list of PI's that are recommended to be used nationally by regulators. This paper has been elaborated based on the information exchanged and discussions held in the February meeting. The participating countries (Spain, Finland, US, Sweden) and WANO were asked to provide an overview of systems in use. The presently used Performance Indicators were reviewed in a three steps process. 1. First indicators used in at least two agencies were identified. 2. The second step was to identify the most used indicators. 3. The third step was to

An overview of safety and environmental considerations in the selection of materials for fusion facilities

International Nuclear Information System (INIS)

Petti, D.A.; Piet, S.J.; Seki, Y.

1996-01-01

Safety and environmental considerations can play a large role in the selection of fusion materials. In this paper, we review the attributes of different structural, plasma facing, and breeding materials from a safety perspective and discuss some generic waste management issues as they relate to fusion materials in general. Specific safety concerns exist for each material that must be dealt with in fusion facility design. Low activation materials offer inherent safety benefits compared with conventional materials, but more work is needed before these materials have the requisite certified databases. In the interim, the international thermonuclear experimental reactor (ITER) has selected more conventional materials and is showing that the safety concerns with these materials can be addressed by proper attention to design. In the area of waste management disposal criteria differ by country. However, the criteria are all very strict making disposal of fusion components difficult. As a result, recycling has gained increasing attention. (orig.)

Measurement tools and process indicators of patient safety culture in primary care. A mixed methods study by the LINNEAUS collaboration on patient safety in primary care

Science.gov (United States)

Parker, Dianne; Wensing, Michel; Esmail, Aneez; Valderas, Jose M

2015-01-01

ABSTRACT Background: There is little guidance available to healthcare practitioners about what tools they might use to assess the patient safety culture. Objective: To identify useful tools for assessing patient safety culture in primary care organizations in Europe; to identify those aspects of performance that should be assessed when investigating the relationship between safety culture and performance in primary care. Methods: Two consensus-based studies were carried out, in which subject matter experts and primary healthcare professionals from several EU states rated (a) the applicability to their healthcare system of several existing safety culture assessment tools and (b) the appropriateness and usefulness of a range of potential indicators of a positive patient safety culture to primary care settings. The safety culture tools were field-tested in four countries to ascertain any challenges and issues arising when used in primary care. Results: The two existing tools that received the most favourable ratings were the Manchester patient safety framework (MaPsAF primary care version) and the Agency for healthcare research and quality survey (medical office version). Several potential safety culture process indicators were identified. The one that emerged as offering the best combination of appropriateness and usefulness related to the collection of data on adverse patient events. Conclusion: Two tools, one quantitative and one qualitative, were identified as applicable and useful in assessing patient safety culture in primary care settings in Europe. Safety culture indicators in primary care should focus on the processes rather than the outcomes of care. PMID:26339832

Industry based performance indicators for nuclear power plants

International Nuclear Information System (INIS)

Connelly, E.M.; Van Hemel, S.B.; Haas, P.M.

1990-07-01

This report presents the results of the first phase of a two-phase study, performed with the goal of developing indirect (leading) indicators of nuclear power plant safety, using other industries as a model. It was hypothesized that other industries with similar public safety concerns could serve as analogs to the nuclear power industry. Many process industries have many more years of operating experience, and many more plants than the nuclear power industry, and thus should have accumulated much useful safety data. In Phase 1, the investigators screened a variety of potential industry analogs and chose the chemical/petrochemical manufacturing industry as the primary analog for further study. Information was gathered on safety programs and indicators in the chemical industry, as well as in the nuclear power industry. Frameworks were selected for the development of indicators which could be transferred from the chemical to the nuclear power environment, and candidate sets of direct and indirect safety indicators were developed. Estimates were made of the availability and quality of data in the chemical industry, and plans were developed for further investigating and testing these candidate indicators against safety data in both the chemical and nuclear power industries in Phase 2. 38 refs., 4 figs., 7 tabs

PROBLEMS OF APPLYING FIXED FORMULAE TO SAFETY CRITERIA AND SITE SELECTION

Energy Technology Data Exchange (ETDEWEB)

Davis, W. K.

1963-10-15

The problem of developing a formula or calculation procedure for that could more-or-less automatically indicate whether or not a nuclear plant would be considered safe at a particular location is discussed. The difficulties and impossibilities of any sach formula for making decisions on siting and safety involving large amounts of money and public safety are considered. (P.C.H.)

Odor composition analysis and odor indicator selection during sewage sludge composting

Science.gov (United States)

Zhu, Yan-li; Zheng, Guo-di; Gao, Ding; Chen, Tong-bin; Wu, Fang-kun; Niu, Ming-jie; Zou, Ke-hua

2016-01-01

ABSTRACT On the basis of total temperature increase, normal dehydration, and maturity, the odor compositions of surface and internal piles in a well-run sewage sludge compost plant were analyzed using gas chromatography–mass spectrometry with a liquid nitrogen cooling system and a portable odor detector. Approximately 80 types of substances were detected, including 2 volatile inorganic compounds, 4 sulfur organic compounds, 16 benzenes, 27 alkanes, 15 alkenes, and 19 halogenated compounds. Most pollutants were mainly produced in the mesophilic and pre-thermophilic periods. The sulfur volatile organic compounds contributed significantly to odor and should be controlled primarily. Treatment strategies should be based on the properties of sulfur organic compounds. Hydrogen sulfide, methyl mercaptan, dimethyl disulfide, dimethyl sulfide, ammonia, and carbon disulfide were selected as core indicators. Ammonia, hydrogen sulfide, carbon disulfide, dimethyl disulfide, methyl mercaptan, dimethylbenzene, phenylpropane, and isopentane were designated as concentration indicators. Benzene, m-xylene, p-xylene, dimethylbenzene, dichloromethane, toluene, chlorobenzene, trichloromethane, carbon tetrachloride, and ethylbenzene were selected as health indicators. According to the principle of odor pollution indicator selection, dimethyl disulfide was selected as an odor pollution indicator of sewage sludge composting. Monitoring dimethyl disulfide provides a highly scientific method for modeling and evaluating odor pollution from sewage sludge composting facilities. Implications: Composting is one of the most important methods for sewage sludge treatment and improving the low organic matter content of many agricultural soils. However, odors are inevitably produced during the composting process. Understanding the production and emission patterns of odors is important for odor control and treatment. Core indicators, concentration indicators, and health indicators provide an index

Odor composition analysis and odor indicator selection during sewage sludge composting.

Science.gov (United States)

Zhu, Yan-Li; Zheng, Guo-di; Gao, Ding; Chen, Tong-Bin; Wu, Fang-Kun; Niu, Ming-Jie; Zou, Ke-Hua

2016-09-01

On the basis of total temperature increase, normal dehydration, and maturity, the odor compositions of surface and internal piles in a well-run sewage sludge compost plant were analyzed using gas chromatography-mass spectrometry with a liquid nitrogen cooling system and a portable odor detector. Approximately 80 types of substances were detected, including 2 volatile inorganic compounds, 4 sulfur organic compounds, 16 benzenes, 27 alkanes, 15 alkenes, and 19 halogenated compounds. Most pollutants were mainly produced in the mesophilic and pre-thermophilic periods. The sulfur volatile organic compounds contributed significantly to odor and should be controlled primarily. Treatment strategies should be based on the properties of sulfur organic compounds. Hydrogen sulfide, methyl mercaptan, dimethyl disulfide, dimethyl sulfide, ammonia, and carbon disulfide were selected as core indicators. Ammonia, hydrogen sulfide, carbon disulfide, dimethyl disulfide, methyl mercaptan, dimethylbenzene, phenylpropane, and isopentane were designated as concentration indicators. Benzene, m-xylene, p-xylene, dimethylbenzene, dichloromethane, toluene, chlorobenzene, trichloromethane, carbon tetrachloride, and ethylbenzene were selected as health indicators. According to the principle of odor pollution indicator selection, dimethyl disulfide was selected as an odor pollution indicator of sewage sludge composting. Monitoring dimethyl disulfide provides a highly scientific method for modeling and evaluating odor pollution from sewage sludge composting facilities. Composting is one of the most important methods for sewage sludge treatment and improving the low organic matter content of many agricultural soils. However, odors are inevitably produced during the composting process. Understanding the production and emission patterns of odors is important for odor control and treatment. Core indicators, concentration indicators, and health indicators provide an index system to odor evaluation

Lean Information Management: Criteria For Selecting Key Performance Indicators At Shop Floor

Science.gov (United States)

Iuga, Maria Virginia; Kifor, Claudiu Vasile; Rosca, Liviu-Ion

2015-07-01

Most successful organizations worldwide use key performance indicators as an important part of their corporate strategy in order to forecast, measure and plan their businesses. Performance metrics vary in their purpose, definition and content. Therefore, the way organizations select what they think are the optimal indicators for their businesses varies from company to company, sometimes even from department to department. This study aims to answer the question of what is the most suitable way to define and select key performance indicators. More than that, it identifies the right criteria to select key performance indicators at shop floor level. This paper contributes to prior research by analysing and comparing previously researched selection criteria and proposes an original six-criteria-model, which caters towards choosing the most adequate KPIs. Furthermore, the authors take the research a step further by further steps to closed research gaps within this field of study.

DOE Safety Metrics Indicator Program (SMIP) Fiscal Year 2000 Annual Report of Packaging- and Transportation-related Occurrences

International Nuclear Information System (INIS)

Dickerson, L.S.

2001-01-01

The U.S. Department of Energy (DOE) Occurrence Reporting and Processing System (ORPS) is an interactive computer system designed to support DOE-owned or -operated facilities in reporting and processing information concerning occurrences related to facility operations. The Oak Ridge National Laboratory has been charged by the DOE National Transportation Program Albuquerque (NTPA) with the responsibility of retrieving reports and information pertaining to packaging and transportation (P and T) incidents from the centralized ORPS database. These selected reports are analyzed for safety concerns, trends, potential impact on P and T operations, and ''lessons learned'' in P and T safety. To support this analysis and trending, the Safety Metrics Indicator Program (SMIP) was established by the NTPA in fiscal year (FY) 1998. Its chief goal is to augment historical reporting of occurrence-based information by providing (1) management notification of those incidents that require attention, (2) an accurate picture of contractors' P and T-related performance, and (3) meaningful statistics on occurrences at particular sites, including comparisons among different contractor sites and between DOE and the private sector. This annual report contains information on those P and T-related occurrences reported to the ORPS during the period from October 1, 1999, through September 30, 2000. Only those incidents that occur in preparation for transport, during transport, and during unloading of hazardous material are considered as packaging- or transportation-related occurrences

Safety code 19: recommended safety procedures for the selection, installation and use of x-ray diffraction equipment

International Nuclear Information System (INIS)

1984-01-01

This document is one of a series of Safety Codes prepared by the Radiation Protection Bureau to set out requirements for the safe use of radiation emitting devices. The equipment and installation guidelines and safety procedures detailed in this Code are primarily for the instruction and guidance of persons employed in Federal Public Service Departments and Agencies, as well as those coming under the jurisdiction of the Canada Labour Code. This Safety Code is also intended to assist other users of X-ray diffraction equipment to select safe equipment and to install and use it so that the radiation hazard to the operator and other persons in its vicinity is negligible. It should be noted that facilities under provincial jurisdiction may be subject to requirements specified under provincial statutes. This Code supersedes Safety Code RPD-SC-7, entitled 'Requirements For Non-Medical X-Ray Equipment, Use and Installation', insofar as X-ray diffraction equipment is concerned, and it is intended to complement X-ray equipment design, construction and performance standards promulgated under the Radiation Emitting Devices Act

NRC safety research in support of regulation. Selected highlights

International Nuclear Information System (INIS)

1986-05-01

The report presents selected highlights of how research has contributed to the regulatory effort. It explains the research role of the NRC and nuclear safety research contributions in the areas of: pressure vessel integrity, piping, small- and large-break loss-of-coolant accidents, hydrogen and containment, source term analysis, seismic hazards and high-level waste management. The report also provides a summary of current and future research directions in support of regulation

Application of proximal surrogate indicators for safety evaluation: A review of recent developments and research needs

Directory of Open Access Journals (Sweden)

S.M. Sohel Mahmud

2017-12-01

Full Text Available Although there have been a number of recent reviews on the use of traffic conflict techniques (TCTs, none have focused on the use of proximal surrogate indicators. This paper comprehensively reviews the development and application of proximal surrogate safety indicators to address this gap. There is a particular focus on more recent advancements in the application of such indicators. For each of the main indicators reviewed, the paper provides a synthesis of the main guiding principles, as well as the most prominent features, including critical or threshold values used in the past. In addition, the main advantages and disadvantages of the reviewed indicators are highlighted. Finally, a number of research gaps are identified together with recommendations for potentially useful avenues of future research. Keywords: Safety evaluation, Traffic conflict, Surrogate, Proximal, Indicators

Research on regularized mean-variance portfolio selection strategy with modified Roy safety-first principle.

Science.gov (United States)

Atta Mills, Ebenezer Fiifi Emire; Yan, Dawen; Yu, Bo; Wei, Xinyuan

2016-01-01

We propose a consolidated risk measure based on variance and the safety-first principle in a mean-risk portfolio optimization framework. The safety-first principle to financial portfolio selection strategy is modified and improved. Our proposed models are subjected to norm regularization to seek near-optimal stable and sparse portfolios. We compare the cumulative wealth of our preferred proposed model to a benchmark, S&P 500 index for the same period. Our proposed portfolio strategies have better out-of-sample performance than the selected alternative portfolio rules in literature and control the downside risk of the portfolio returns.

An index of financial safety of China

Directory of Open Access Journals (Sweden)

Xiaojun Jia

2015-04-01

Full Text Available Purpose: This paper combines a synthetic index system by the variables and evaluates China’s financial safety through the change of indexes in a comprehensive way. First of all, it builds the financial industry evaluation index system composed of 25indicators in terms of the operation of the financial industry and external economic environment and particularly takes into consideration factors which might trigger liquidity risks such as off-balance-sheet business, interbank business and shadow banking; then it selects 10 indicators to conduct empirical analysis and identifies the indicator weight through principal component analysis; finally it combines the financial safety indexes through the linear weighted comprehensive evaluation model.Design/methodology/approach: Synthesis of indexes is made by constructing a proper comprehensive evaluation mathematical model, integrating a number of evaluation indexes into one comprehensive evaluation index and then obtaining corresponding comprehensive evaluation results. In this paper, it selects 10 indexes to conduct empirical analysis and identifies the index weight through principal component analysis; finally it combines the financial safety indexes through the linear weighted comprehensive evaluation model. Principal component analysis (PCA is a statistical procedure that uses an orthogonal transformation to convert a set of observations of possibly correlated variables into a set of values of linearly uncorrelated variables called principal components. PCA was invented in 1901 and was later independently developed (and named by Harold Hotelling in the 1930s.Findings: From 2003 to 2013 China’s financial safety indexes fluctuated. From 2003 to 2007 indexes rose, which indicates China’s financial safety status gradually improved; from 2007 to 2009 indexes declined, which indicates due to the impact of subprime crisis, China’s financial safety status took a turn for the worse; from 2009 to 2012

Hospital Accreditation: What is its Effect on Quality and Safety Indicators? Experience of an Iranian teaching hospital

Directory of Open Access Journals (Sweden)

Ali Janati

2016-07-01

Full Text Available Background: program evaluation is an integral and expected component in the development of any healthcare program. It helps decision-makers to base their decisions on facts. Objective: This paper analyzes the effect of accreditation on three indicators related to patient safety and hospital care quality in ICU wards of an Iranian teaching hospital. Methods: This interventional study was accomplished based on executive management and scientific methods such as plan-do-check-act (PDCA cycle and audit to improve quality and safety. We used data reported from ICU wards of the hospital to analyze the effect of accreditation on the three selected indicators. (SPSS version 22.00 was used for the statistical analysis. Results: In total, 6997 patients were analyzed. The accreditation interventions appeared to be effective at reducing pressure ulcer incidence average (from an average of 6.8 percent to 4.1 percent (p=0.045. The accreditation also. The average stay of the patients during the study also positively changed from an average of 1.58 days to 10.13 days (1.45 improvements(p=0.0303. In relation to hospital acquired infection but, unexpectedly, its effect on hospital was negative, then it considerably increased and rose from 1.5 percent to 8.1 percent (p=0.001. However this increasing was due to enhanced infection incident report system. Conclusion: hospital accreditation has presented ample opportunity a significant positive effect on hospitals. 

Assessing the Utility of Temporally Dynamic Terrain Indices in Alaskan Moose Resource Selection

Science.gov (United States)

Jennewein, J. S.; Hebblewhite, M.; Meddens, A. J.; Gilbert, S.; Vierling, L. A.; Boelman, N.; Eitel, J.

2017-12-01

The accelerated warming in arctic and boreal regions impacts ecosystem structure and plant species distribution, which have secondary effects on wildlife. In summer months, moose (Alces alces) are especially vulnerable to changes in the availability and quality of forage and foliage cover due to their thermoregulatory needs and high energetic demands post calving. Resource selection functions (RSFs) have been used with great success to model such tradeoffs in habitat selection. Recently, RSFs have expanded to include more dynamic representations of habitat selection through the use of time-varying covariates such as dynamic habitat indices. However, to date few studies have investigated dynamic terrain indices, which incorporate long-term, highly-dynamic meteorological data (e.g., albedo, air temperature) and their utility in modeling habitat selection. The purpose of this study is to compare two dynamic terrain indices (i.e., solar insolation and topographic wetness) to their static counterparts in Alaskan moose resource selection over a ten-year period (2008-2017). Additionally, the utility of a dynamic wind-shelter index is assessed. Three moose datasets (n=130 total), spanning a north-to-south gradient in Alaska, are analyzed independently to assess location-specific resource selection. The newly-released, high-resolution Arctic Digital Elevation Model (5m2) is used as the terrain input into both dynamic and static indices. Dynamic indices are programmed with meteorological data from the North American Regional Analysis (NARR) and NASA's Goddard Earth Sciences Data and Information Services Center (GES-DISC) databases. Static wetness and solar insolation indices are estimated using only topographic parameters (e.g., slope, aspect). Preliminary results from pilot analyses suggest that dynamic terrain indices may provide novel insights into resource selection of moose that could not be gained when using static counterparts. Future applications of such dynamic

Serious injuries: an additional indicator to fatalities for road safety benchmarking.

Science.gov (United States)

Shen, Yongjun; Hermans, Elke; Bao, Qiong; Brijs, Tom; Wets, Geert

2015-01-01

Almost all of the current road safety benchmarking studies focus entirely on fatalities, which, however, represent only one measure of the magnitude of the road safety problem. The main objective of this article was to investigate the possibility of including the number of serious injuries in addition to the number of fatalities for road safety benchmarking and to further illuminate its impact on the countries' rankings. We introduced the technique of data envelopment analysis (DEA) to the road safety domain and developed a DEA-based road safety model (DEA-RS) in this study. Moreover, we outlined different types of possible weight restrictions and adopted 2 of them to indicate the relationship between road fatalities and serious injuries for the sake of rational benchmarking. One was a relative weight restriction based on the information of their shadow price, and the other was a virtual weight restriction using a priori knowledge about the importance level of these 2 aspects. By computing the most optimal road safety risk scores of 10 European countries based on the different models, we found that United Kingdom was the only best-performing country no matter which model was utilized. However, countries such as The Netherlands, Sweden, and Switzerland were no longer best-performing when the serious injuries were integrated. On the contrary, Spain, which ranked almost at the bottom among all of the countries when only the number of road fatalities was considered, became a relatively well-performing country when integrating its number of serious injuries in the evaluation. In general, no matter whether the country's road safety ranking was improved or deteriorated, most of the countries achieved a higher risk score when the number of serious injuries was included, which implied that compared to the road fatalities, more policy attention has to be paid to improve the situation of serious injuries in most countries. Given the importance of considering the serious

Implementation of an indicator-based safety management system for the EnKK NPP's

International Nuclear Information System (INIS)

Bassing, G.; Nasellu, M.; Ritter, J.

2004-01-01

This presentation at the Eurosafe Berlin 2004 will give an overview of the activities on safety management of EnBW Kernkraft GmbH taken up with a notifiable event in August 2001 at KKP 2 nuclear site. After this event EnBW announced the development and introduction of an indicator-based safety management system (SMS) at all sites of its nuclear power plants. A SMS team with members from all NPP sites was built which had to analyse all processes based on the DIN EN ISO 9000 philosophy and to control them by indicators. The regulatory authorities and their experts would accompany this process in a suitable fashion and monitor and review it after its introduction. This presentation shows the process during the development of the system, the status of its introduction and the general involvement of the regulator. (orig.)

Application of non-dose/risk indicators for confidence-building in the H12 safety assessment

International Nuclear Information System (INIS)

Miyahara, K.; Makino, H.; Takasu, A.; Naito, M.; Umeke, H.; Wakasugi, K.; Ishiguro, K.

2002-01-01

In the H12 study, non-dose/risk safety indicators have also been considered with a view to increasing confidence in the safety assessment. The H12 safety assessment considers system evolution for a range of scenarios; not only normal groundwater scenarios but also isolation failure scenarios due to unlikely natural disruptive events. The calculated nuclide concentrations and fluxes in the surface environment for the reference groundwater scenario were compared with measurements of naturally occurring nuclides. This comparison indicated that the concentration and fluxes of radionuclides released from the repository would be several orders of magnitude lower than those of natural radionuclides. There may exist cases, such as some natural disruptive events, where the likelihood of occurrence is extremely low and the 'Reference Biosphere' approach is difficult to be applied for biosphere modelling. The use of qualitative assessment to allow comparison with naturally occurring nuclides based on observations of natural systems may play a role in supporting the robustness of the system concept. These examples suggest that relevant application of these non-dose/risk indicators supports a more robust case. An advantage to applying such indicators is that both technical and non-technical audiences can judge the relative, long-term impact of a deep geological repository. (author)

Operational safety performance indicator system - a management tool for the self assessment of safety and reliability of nuclear power plants

International Nuclear Information System (INIS)

Anil Kumar; Mandowara, S.L.; Mittal, S.

2006-01-01

Operational Safety Performance Indicator system is one of the self assessment tools for station management to monitor safety and reliability of nuclear power plants. It provides information to station management about the performance of various areas of the plants by means of different colours of relevant performance indicators. Such systems have been implemented at many nuclear power plants in the world and have been considered as strength during WANO Peer Review. IAEA had a Coordinated Research Programme (CRP) on this with several countries participating including India. In NPCIL this system has been implemented in KAPS about a year back and found very useful in identifying areas which needs to be given more attention. Based on the KAPS feedback Implementation of this system has been taken up in RAPS-3 and 4 and KGS-l and 2. (author)

Expanding Resilience Indicators: A Case Study on Buffering Capacity Indicator in a Process Plant

Directory of Open Access Journals (Sweden)

Shirali

2016-03-01

Full Text Available Background The complexity of modern sociotechnical systems has created new challenges for safety, so that traditional approaches are not able to cope with them. Resilience engineering (RE is a good alternative to traditional approaches for safety management, however resilience is still a difficult concept to measure, and indicators such as buffering capacity, flexibility, and so on, which are thought to contribute to it, are undeveloped. Objectives This study aimed at expanding buffering capacity as one of the main indicators in order to facilitate measurement of resilience of a system. Materials and Methods We used the Delphi method in order to identify indicators, and data related to all the indicators were gathered by observation and interview. In this line, 32 of the experienced operators with at least 15 years of operational record were selected for semi-structured interviews. Gathered data was processed by the principal component analysis technique. The results were processed by the Minitab 15 software. Results In this study, 29 factors affecting this indicator were determined using the Delphi method; the scores of all factors were less than the scores of the best practice. On the other hand, the state of this indicator was poor in plant included in the study. Conclusions This was the first study that focused on expanding resilience indicators, and presents a new framework to simplify assessment of resilience and safety of a complex system.

Research on professional adaptability psychological selection indices of nuclear power plant operators

International Nuclear Information System (INIS)

Liu Jingquan; Li Zhe; Li Maoyou

2010-01-01

Based on the analysis of the work characteristics of nuclear power plant operators and the comparison of professional psychological selection indices for different occupations, the indices of psychological selection system which is applicable to nuclear power plant operators are proposed in this paper, using the method named 'taking classes,cross-comparison'. The index results of the suggested psychological selection system reflects all the professional requirements on the nuclear power plant operators, which can also be used for the recruitment, training and the retraining programs for operators. (authors)

Development and integration of programmatic performance indicators

International Nuclear Information System (INIS)

Modarres, M.; Wrethall, J.; Appignani, P.L.

1989-01-01

This paper describes the results of an evaluation of maintenance-related programmatic performance indicators, and summarizes the direction being taken in a new project to integrate indirect performance indicators for nuclear power plants. Programmatic indicators allow NRC to monitor, at a distance, trends in functional activities before a significant impact appears on safety. Previously presented work described the selection of candidate performance indicators associated with maintenance for continued analysis. This evaluation focused on two aspects of the selected indicators: (1) an evaluation of the state of maintenance programs in the narrative text of SALP reports versus the frequencies of inadvertent ESF actuations from test and maintenance errors; and (2) an evaluation of alternative methods for analyzing the thermal performance of plants as an integral indicator of maintenance program effectiveness. 1 ref., 1 fig

A systems approach to risk management through leading safety indicators

International Nuclear Information System (INIS)

Leveson, Nancy

2015-01-01

The goal of leading indicators for safety is to identify the potential for an accident before it occurs. Past efforts have focused on identifying general leading indicators, such as maintenance backlog, that apply widely in an industry or even across industries. Other recommendations produce more system-specific leading indicators, but start from system hazard analysis and thus are limited by the causes considered by the traditional hazard analysis techniques. Most rely on quantitative metrics, often based on probabilistic risk assessments. This paper describes a new and different approach to identifying system-specific leading indicators and provides guidance in designing a risk management structure to generate, monitor and use the results. The approach is based on the STAMP (System-Theoretic Accident Model and Processes) model of accident causation and tools that have been designed to build on that model. STAMP extends current accident causality to include more complex causes than simply component failures and chains of failure events or deviations from operational expectations. It incorporates basic principles of systems thinking and is based on systems theory rather than traditional reliability theory. - Highlights: • Much effort has gone into developing leading indicators with only limited success. • A systems-theoretic, assumption-based approach may be more successful. • Leading indicators are warning signals of an assumption’s changing vulnerability. • Heuristic biases can be controlled by using plausibility rather than likelihood

Selected indicators for evaluating the effectiveness of marketing communication

Directory of Open Access Journals (Sweden)

Aneta Olejniczak

2015-06-01

Full Text Available The issue of the evaluation of marketing activity in each institution most often refers to marketing communications and therefore promotional activities of the company. Whereas measuring the effectiveness of marketing communications results, we can use many tools-indicators, the use of which will track the progress and assess the effectiveness of our institution run by marketing communications. With a view to implementing effective marketing strategy we must be able to measure our success. In this article, has been made a review of selected indicators to evaluate the effectiveness of marketing communications. Cited indicators are commonly used. According to the authors, each institution should create its own set of indicators by which the effects of its operations will be best measured.

Food Safety and Sanitary Practices of Selected Hotels in Batangas Province, Philippines: Basis of Proposed Enhancement Measures

Directory of Open Access Journals (Sweden)

April M. Perez

2017-02-01

Full Text Available This study assessed the extent of food safety and sanitary practices of selected hotels in Batangas province as basis of proposed enhancement measures. The study utilized descriptive method to describe food safety and sanitary practices of selected hotels in Batangas province with a total of 8 hotels (256 respondents. Purposive sampling was used in the study. The questionnaires were designed using the provision of the Sanitation Code of the Philippines, validated and finalized to come up with legitimate results. The study showed that there were eight (8 hotel respondents classified as two, three, four star with considerable years of experience and adequate number of employees. The hotels demonstrated the food safety and sanitary practices always in the areas of restaurant, bar service, catering and banquet and room service. The significant pair-wise comparison for restaurant, bar service, catering and banquet and room service shows that 2 star hotels greatly differs. The researcher recommends that the management should maintain high standard of food safety and sanitary practices among its staff, upgrade the food safety and sanitary practices for food safety accreditation, continuous training of the hotel managers/employees on food safety and sanitary practices.

EU DEMO blanket concepts safety assessment. Final report of Working Group 6a of the Blanket Concept Selection Exercise

International Nuclear Information System (INIS)

Kleefeldt, K.; Porfiri, T.

1996-06-01

The European Union has been engaged since 1989 in a programme to develop tritium breeding blankets for application in a fusion power reactor. There are four blanket concepts under development. Two of them use lithium ceramics, the other two concepts employ an eutectic lead-lithium alloy (Pb-17Li) as breeder material. The two most promising concepts were to select in 1995 for further development. In order to prepare the selection, a Blanket Concept Selection Exercise (BCSE) has been inititated by the participating associations under the auspices of the European Commission. This BCSE has been performed in 14 working groups which, in a comparative evaluation of the four blanket concepts, addressed specific fields. The working group safety addressed the safety implications. This report describes the methodology adopted, the safety issues identified, their comparative evaluation for the four concepts, and the results and conclusions of the working group to be entered into the overall evaluation. There, the results from all 14 working groups have been combined to yield a final ranking as a basis for the selection. In summary, the safety assessment showed that the four European blanket concepts can be considered as equivalent in terms of the safety rating adopted, each concept, however, rendering safety concerns of different quality in different areas which are substantiated in this report. (orig.) [de

Culture of safety. Indicators of culture of safety. Stage of culture of safety. Optimization of radiating protection. Principle of precaution. Principle ALARA. Procedure ALARA

International Nuclear Information System (INIS)

Mursa, E.

2006-01-01

Object of research: is the theory and practice of optimization of radiating protection according to recommendations of the international organizations, realization of principle ALARA and maintenance of culture of safety (SC) on the nuclear power plant. The purpose of work - to consider the general aspects of realization of principle ALARA, conceptual bases of culture of safety, as principle of management, and practice of their introduction on the nuclear power plant. The work has the experts' report character in which the following questions are presented: The recommendations materials of the IAEA and other international organizations have been assembled, systematized and analyzed. The definitions, characteristics and universal SC features, and also indicators as a problem of parameters and quantitative SC measurements are described in details advanced. The ALARA principles - principle of precaution; not acceptance of zero risk; choice of a principle ALARA; model of acceptable radiation risk are described. The methodology of an estimation of culture of safety level and practical realization of the ALARA principle in separate organization is shown on a practical example. The SC general estimation at a national level in Republic of Moldova have been done. Taking into consideration that now Safety Culture politics are introduced only in relation to APS, in this paper the attempt of application of Safety Culture methodology to Radiological Objects have been made (Oncological Institute of the Republic of Moldova and Special Objects No.5101 and 5102 for a long time Storage of the Radioactive Waste). (authors)

Occupational safety training and practices in selected vocational training institutions and workplaces in Kampala, Uganda.

Science.gov (United States)

Kintu, Denis; Kyakula, Michael; Kikomeko, Joseph

2015-01-01

Several industrial accidents, some of them fatal, have been reported in Uganda. Causes could include training gaps in vocational training institutions (VTIs) and workplaces. This study investigated how occupational safety training in VTIs and workplaces is implemented. The study was carried out in five selected VTIs and workplaces in Kampala. Data were collected from instructors, workshop technicians, students, workshop managers, production supervisors, machine operators and new technicians in the workplaces. A total of 35 respondents participated in the study. The results revealed that all curricula in VTIs include a component of safety but little is practiced in VTI workshops; in workplaces no specific training content was followed and there were no regular consultations between VTIs and industry on safety skills requirements, resulting in a mismatch in safety skills training. The major constraints to safety training include inadequate funds to purchase safety equipment and inadequate literature on safety.

The development and evaluation of programmatic performance indicators associated with maintenance at nuclear power plants

International Nuclear Information System (INIS)

Wreathall, J.; Fragola, J.; Appignani, P.; Burlile, G.; Shen, Y.

1990-05-01

This report summarizes the development and evaluation of programmatic performance indicators of maintenance. These indicators were selected by: (1) creating a formal framework of plant processes; (2) identifying features of plant behavior considered important to safety; (3) evaluating existing indicators against these features; and (4) performing statistical analyses for the selected indicators. The report recommends additional testing. 32 refs., 29 figs., 11 tabs

Safety analysis SFR 1. Long-term safety

Energy Technology Data Exchange (ETDEWEB)

2008-12-15

authorities' previous review comments. Furthermore, definitions are given of terms and abbreviations used in SAR- 08, General Part 2, 'Long-term safety'. Chapter 2 Method. The chapter provides an overall description of the method used for the safety assessment and some aspects of the methodology are presented, such as time periods, safety principles, management of uncertainties, quality assurance and risk management. Chapter 3 Identification, ranking and handling of FEPs. The chapter systematically describes the factors to be taken into account in the assessment in the form of features, events and processes (FEPs). Interaction matrices are used to structure the information. Chapter 4 Initial state in the repository and its environs. The chapter describes the initial state, defined as the expected state of the repository and its environs, at closure in 2040. The description of the initial state is based on the technical design of the repository, present-day knowledge concerning conditions in the repository and its environs, and the expected evolution of the repository up until 2040. Chapter 5 Safety functions and safety performance indicators. Safety functions and safety performance indicators are identified and described in this chapter. A safety function is a role by means of which a repository component contributes to safety. Chapter 6 Reference evolution for the repository and its environs. This chapter describes the reference evolution of the repository and its environs and how the safety functions of the repository can be affected by this evolution up until 100,000 years after closure. Chapter 7 Selection of scenarios. This chapter describes how scenarios are selected based on safety performance indicators and interaction matrices. The selected scenarios illustrate the most important processes leading to the migration of radionuclides in the repository and to exposure of man and environment. The description of the processes is based on the evolution of the repository

Safety analysis SFR 1. Long-term safety

International Nuclear Information System (INIS)

2008-12-01

authorities' previous review comments. Furthermore, definitions are given of terms and abbreviations used in SAR- 08, General Part 2, 'Long-term safety'. Chapter 2 Method. The chapter provides an overall description of the method used for the safety assessment and some aspects of the methodology are presented, such as time periods, safety principles, management of uncertainties, quality assurance and risk management. Chapter 3 Identification, ranking and handling of FEPs. The chapter systematically describes the factors to be taken into account in the assessment in the form of features, events and processes (FEPs). Interaction matrices are used to structure the information. Chapter 4 Initial state in the repository and its environs. The chapter describes the initial state, defined as the expected state of the repository and its environs, at closure in 2040. The description of the initial state is based on the technical design of the repository, present-day knowledge concerning conditions in the repository and its environs, and the expected evolution of the repository up until 2040. Chapter 5 Safety functions and safety performance indicators. Safety functions and safety performance indicators are identified and described in this chapter. A safety function is a role by means of which a repository component contributes to safety. Chapter 6 Reference evolution for the repository and its environs. This chapter describes the reference evolution of the repository and its environs and how the safety functions of the repository can be affected by this evolution up until 100,000 years after closure. Chapter 7 Selection of scenarios. This chapter describes how scenarios are selected based on safety performance indicators and interaction matrices. The selected scenarios illustrate the most important processes leading to the migration of radionuclides in the repository and to exposure of man and environment. The description of the processes is based on the evolution of the repository

Safety analysis SFR 1. Long-term safety

Energy Technology Data Exchange (ETDEWEB)

2008-12-15

regulatory authorities' previous review comments. Furthermore, definitions are given of terms and abbreviations used in SAR- 08, General Part 2, 'Long-term safety'. Chapter 2 Method. The chapter provides an overall description of the method used for the safety assessment and some aspects of the methodology are presented, such as time periods, safety principles, management of uncertainties, quality assurance and risk management. Chapter 3 Identification, ranking and handling of FEPs. The chapter systematically describes the factors to be taken into account in the assessment in the form of features, events and processes (FEPs). Interaction matrices are used to structure the information. Chapter 4 Initial state in the repository and its environs. The chapter describes the initial state, defined as the expected state of the repository and its environs, at closure in 2040. The description of the initial state is based on the technical design of the repository, present-day knowledge concerning conditions in the repository and its environs, and the expected evolution of the repository up until 2040. Chapter 5 Safety functions and safety performance indicators. Safety functions and safety performance indicators are identified and described in this chapter. A safety function is a role by means of which a repository component contributes to safety. Chapter 6 Reference evolution for the repository and its environs. This chapter describes the reference evolution of the repository and its environs and how the safety functions of the repository can be affected by this evolution up until 100,000 years after closure. Chapter 7 Selection of scenarios. This chapter describes how scenarios are selected based on safety performance indicators and interaction matrices. The selected scenarios illustrate the most important processes leading to the migration of radionuclides in the repository and to exposure of man and environment. The description of the processes is based on the

Some safety considerations in the selection of redans for pool-type LMR plants

International Nuclear Information System (INIS)

Pan, Y.C.; Pedersen, D.R.; Wang, C.Y.

1985-01-01

Three basic safety issues in the selection of the redan design for a pool type liquid metal fast breeder reactor plant are examined. The first area examined is the effect of the redan selection on the integrity of the primary system pressure boundary in normal and offset conditions. The second area is on the consequence of the hypothetical core disruptive accident. The third area is on the consequence of the loss of heat sink accident. Some general discussion and numerical results are presented which may help in the selection of an optimum redan design. 3 refs., 7 figs

Leadership for safety: industrial experience.

Science.gov (United States)

Flin, R; Yule, S

2004-12-01

The importance of leadership for effective safety management has been the focus of research attention in industry for a number of years, especially in energy and manufacturing sectors. In contrast, very little research into leadership and safety has been carried out in medical settings. A selective review of the industrial safety literature for leadership research with possible application in health care was undertaken. Emerging findings show the importance of participative, transformational styles for safety performance at all levels of management. Transactional styles with attention to monitoring and reinforcement of workers' safety behaviours have been shown to be effective at the supervisory level. Middle managers need to be involved in safety and foster open communication, while ensuring compliance with safety systems. They should allow supervisors a degree of autonomy for safety initiatives. Senior managers have a prime influence on the organisation's safety culture. They need to continuously demonstrate a visible commitment to safety, best indicated by the time they devote to safety matters.

Performance indicators and combining assessments to evaluate the safety performance of licensees

International Nuclear Information System (INIS)

Aubrey, Richard; Van Binnebeek, J.J.; Warren, T.F.H.

1998-01-01

The CNRA believes that safety inspections are a major element in the regulatory authority's efforts to ensure the safe operation of nuclear facilities. Considering the importance of these issues, the Committee has established a special Working Group on Inspection Practices (WGIP). The purpose of WGIP, is to facilitate the exchange of information and experience related to regulatory safety inspections between CNRA Member countries. As a follow-up to the 1995 document on Compilation of Responses to a Questionnaire on the Evaluation of the Safety Performance of Licensees, WGIP members identified several issues where additional information would be useful in future meetings and discussions. The consensus of the Group was that performance indicators (PIs) and how assessments are combined were the two issues that should be addressed first. It was noted also that in addition to information in obtained through the questionnaire, results from the workshop in May 1996 may provide valuable input to the endeavour. This report summarises a review conducted of the PI-related information provided by the questionnaire, the workshop, and responses from WGIP members to a request for specific information not addressed previously

Draft report: a selection methodology for LWR safety R and D programs and proposals

International Nuclear Information System (INIS)

Husseiny, A.A.; Ritzman, R.L.

1980-03-01

The results of work done to develop a methodology for selecting LWR safety R and D programs and proposals is described. A critical survey of relevant decision analysis methods is provided including the specifics of multiattribute utility theory. This latter method forms the basis of the developed selection methodology. Details of the methodology and its use are provided along with a sample illustration of its application

Draft report: a selection methodology for LWR safety R and D programs and proposals

Energy Technology Data Exchange (ETDEWEB)

Husseiny, A. A.; Ritzman, R. L.

1980-03-01

The results of work done to develop a methodology for selecting LWR safety R and D programs and proposals is described. A critical survey of relevant decision analysis methods is provided including the specifics of multiattribute utility theory. This latter method forms the basis of the developed selection methodology. Details of the methodology and its use are provided along with a sample illustration of its application.

Occupational Safety Review of High Technology Facilities

Energy Technology Data Exchange (ETDEWEB)

Lee Cadwallader

2005-01-31

This report contains reviews of operating experiences, selected accident events, and industrial safety performance indicators that document the performance of the major US DOE magnetic fusion experiments and particle accelerators. These data are useful to form a basis for the occupational safety level at matured research facilities with known sets of safety rules and regulations. Some of the issues discussed are radiation safety, electromagnetic energy exposure events, and some of the more widespread issues of working at height, equipment fires, confined space work, electrical work, and other industrial hazards. Nuclear power plant industrial safety data are also included for comparison.

Selected safety aspects of containments for nuclear power plants with WWER-440 reactors

International Nuclear Information System (INIS)

Jankowski, M.W.; Kulig, M.J.; Strupczewski, A.; Balabanov, E.D.

1996-01-01

Considerable attention has been and continues to be focused on the design and operational features that prevent the release of radioactive materials to the environment for a spectrum of accidents for the two classes of WWER-440 reactors: the older 230 model and the more recently designed 213 models. This paper, based on published and unpublished information, aims to clarify the perceptions of the Russian WWER-440 models 230 and 213 nuclear power plant containment system designs and their relevance to selected aspects of accident mitigation. It should be noted that these are unclearly and often negatively perceived, primarily because of a lack of reliable information and a poorly assembled experimental database. Conflicting statements have been made regarding the nature and the features of the plant's containment system. The paper presents a brief outline of the design of both WWER-440 models with respect to their confinement functions. Selected safety-related aspects of the accident localization systems are discussed, and the recognized shortcomings and safety merits are pointed out. The older 230 units experience high leak rates and are designed to withstand medium-size pipe breaks. The possible implications for safety are pointed out in the paper. The on going studies that concentrate on improving the system are highlighted. (orig.)

Methodological proposal for evaluating and selecting environment al indicators, Case: Chachafruto Stream Basin, Rionegro, Antioquia, Colombia

International Nuclear Information System (INIS)

Osorio Velez, Luis Fernando; Pineda Correa, Marcelena

2000-01-01

The investigation mainly responds to the necessity of developing a methodology that allows getting indicators to make easier the process of making decisions in the environmental administration field. The elaboration was relied on the support of the Corporacion Autonoma Regional Rionegro - Nare CORNARE in Antioquia - Colombia, through a subscribed agreement between this entity and the authors. The development of the investigation was carried out in two parts: the first involves the search of methodological paths for the evaluation and selection of applicable indicators to basins, Through the creation of parameters that allow qualifying these indicators in direct form; this is followed by a statistical treatment that allows selecting indicators in a rational way. For application purposes, some criterions are defined in a such way that the selected indicators can be evaluated; with these criterions the matrix is constructed; this allows to view and qualify the indicators, starting from ranges and scales previously defined; once the evaluation and qualification matrix are carried out, the selection process is begun from multivariate analysis. The second part consists in the methodology application expounded to a pattern of indicators previously defined and a determined territory (Basin of the Chachafruto Stream, Rionegro - Antioquia - Colombia); starting from the listing of the whole reported indicators in the consulted literature, the ability of themselves to reflex the basin problems is analyzed, based on parameters such as local contextualization and focuses of the topic. Once the first selection is done, the indicators are submitted to the qualification and evaluation matrix and its results are analyzed by multivariate analysis, in order to condense the environmental indicators to be used. Subsequently, for the evaluation of selected indicators, it is necessary to compile diverse thematic information and to identify the existent databases for the select territory

Dashboard report on performance on select quality indicators to cancer care providers.

Science.gov (United States)

Stattin, Pär; Sandin, Fredrik; Sandbäck, Torsten; Damber, Jan-Erik; Franck Lissbrant, Ingela; Robinson, David; Bratt, Ola; Lambe, Mats

2016-01-01

Cancer quality registers are attracting increasing attention as important, but still underutilized sources of clinical data. To optimize the use of registers in quality assurance and improvement, data have to be rapidly collected, collated and presented as actionable, at-a-glance information to the reporting departments. This article presents a dashboard performance report on select quality indicators to cancer care providers. Ten quality indicators registered on an individual patient level in the National Prostate Cancer Register of Sweden and recommended by the National Prostate Cancer Guidelines were selected. Data reported to the National Prostate Cancer Register are uploaded within 24 h to the Information Network for Cancer Care platform. Launched in 2014, "What''s Going On, Prostate Cancer" provides rapid, at-a-glance performance feedback to care providers. The indicators include time to report to the National Prostate Cancer Register, waiting times, designated clinical nurse specialist, multidisciplinary conference, adherence to guidelines for diagnostic work-up and treatment, and documentation and outcome of treatment. For each indicator, three performance levels were defined. What's Going On, a dashboard performance report on 10 selected quality indicators to cancer care providers, provides an example of how data in cancer quality registers can be transformed into condensed, at-a-glance information to be used as actionable metrics for quality assurance and improvement.

Ecological Safety Evaluation of Land Use in Ji’an City Based on the Principal Component Analysis

Institute of Scientific and Technical Information of China (English)

2010-01-01

According to the ecological safety evaluation index data of land-use change in Ji’an City from 1999 to 2008,positive treatment on selected reverse indices is conducted by Reciprocal Method.Meanwhile,Index Method is used to standardize the selected indices,and Principal Component Analysis is applied by using year as a unit.FB is obtained,which is related with the ecological safety of land-use change from 1999 to 2008.According to the scientific,integrative,hierarchical,practical and dynamic principles,ecological safety evaluation index system of land-use change in Ji’an City is established.Principal Component Analysis and evaluation model are used to calculate four parameters,including the natural resources safety index of land use,the socio-economic safety indicators of land use,the eco-environmental safety index of land use,and the ecological safety degree of land use in Ji’an City.Result indicates that the ecological safety degree of land use in Ji’an City shows a slow upward trend as a whole.At the same time,ecological safety degree of land-use change is relatively low in Ji’an City with the safety value of 0.645,which is at a weak safety zone and needs further monitoring and maintenance.

A comparative study of radiation safety practices at selected hospitals in the UK and USA

International Nuclear Information System (INIS)

White, D.R.; Showalter, C.K.; Hamilton, D.R.

1984-01-01

The radiation safety practices in a group of 25 UK and USA hospitals have recently been assessed. This took the form of detailed inspections of some 62 medical radiation departments, including Diagnostic X-ray, Radiotherapy, Nuclear Medicine and Pathology/Research (Radionuclide) Departments. Empirical expressions called ''Radiation Safety Indices'' were devised to evaluate the incidence of personal doses and radiological incidents occurring from 1977-82 and to characterise the safety facilities, procedures, supervision and educational techniques in each department. An outline is given of national legislative material and voluntary codes of conduct, together with the results of the departmental inspections. The computed indices are presented graphically and an analysis given of apparent national trends. (author)

Study on the selection method of feed water heater safety valves in nuclear power plants

International Nuclear Information System (INIS)

Shi Jianzhong; Huang Chao; Hu Youqing

2014-01-01

The selection of the high pressure feedwater heater's safety valve usually follows the principle recommended by HEI standards in thermal power plant. However, the nuclear power plant's heaters generally need to accept a lots of drain from a moisture separator reheater (MSR). When the drain regulating valve was failure in fully open position, a large number of high pressure steam will directly goes into the heater. It make high-pressure heater have a risk of overpressure. Therefore, the safety valve selection of the heaters for nuclear power plants not only need to follow the HEI standards, but also need to check his capacity in certain special conditions. The paper established a calculation method to determine the static running point of the heaters based on characteristic equations of the feed water heater, drain regulating valve and steam extraction pipings, and energy balance principle. The method can be used to calculate the equilibrium pressure of various special running conditions, so further determine whether the capacity of the safety valve meets the requirements of safety and emissions. The method proposed in this paper not only can be used for nuclear power plants, can also be used for thermal power plants. (authors)

Indicators of School Crime Safety, 2000.

Science.gov (United States)

Kaufman, Phillip; Chen, Xianglei; Choy, Susan P.; Ruddy, Sally A.; Miller, Amanda K.; Fleury, Jill K.; Chandler, Kathryn A.; Rand, Michael R.; Klaus, Patsy; Planty, Michael

Providing the latest data, this report on school safety presents a mixed picture: while overall crime has declined, violence, gangs, and drugs remain at some schools. Victimization at school declined from 1995-99, though rates for fighting and weapon threats remain steady. Students seem more secure, and gang activity decreased; however, in grades…

Road safety performance indicators : country profiles. SafetyNet, Building the European Road Safety Observatory, Workpackage 3, Deliverable 3.7b.

NARCIS (Netherlands)

Riguelle, F. Eksler, V. Holló, P. Morsink, P. Gent, A. van Gitelman, V. Assum, T. & Rackliff, L.

2009-01-01

The EC 6th Framework Integrated Project SafetyNet aims to accelerate the availability and use of harmonised road safety data in Europe. Having such data available throughout Europe would be tremendously beneficial for road safety, since it would enable the evaluation of road safety measures, the

A Heckman selection model for the safety analysis of signalized intersections.

Directory of Open Access Journals (Sweden)

Xuecai Xu

Full Text Available The objective of this paper is to provide a new method for estimating crash rate and severity simultaneously.This study explores a Heckman selection model of the crash rate and severity simultaneously at different levels and a two-step procedure is used to investigate the crash rate and severity levels. The first step uses a probit regression model to determine the sample selection process, and the second step develops a multiple regression model to simultaneously evaluate the crash rate and severity for slight injury/kill or serious injury (KSI, respectively. The model uses 555 observations from 262 signalized intersections in the Hong Kong metropolitan area, integrated with information on the traffic flow, geometric road design, road environment, traffic control and any crashes that occurred during two years.The results of the proposed two-step Heckman selection model illustrate the necessity of different crash rates for different crash severity levels.A comparison with the existing approaches suggests that the Heckman selection model offers an efficient and convenient alternative method for evaluating the safety performance at signalized intersections.

Discussion of indication for selecting ectopic pregnancy treated by trans-uterine artery embolization

International Nuclear Information System (INIS)

Xu Wenjian; Ni Caifang; Tan Xiaomei

2007-01-01

Objective: To discuss the selection of indication for using uterine artery perfusion and embolization in tubal pregnancy. Methods: Fifty one cases of tubal pregnancy were treated by superselective trans-uterine artery (TUA) catheterization with perfusing Methorexate (MTX) and then embolized the uterine arteries by gelfoam. The comparisons among serum β-HCG concentration, abdominal bleeding and the size of the ectopic mass could state the importance of the indication selection preproceduralty. Results: Forty eight of the 51 cases were cured by this method, when the ectopic mass size ≥5 cm, the cure rate was low, 33.33% (P<0.01), although the serum β-HCG concentration was ≤10 000 mIU/ml with no abdominal hemorrhage; otherwise, with mass size ≤5 cm, without consideration of the serum β-HCG concentration and abdominal bleeding, the cure rate was 97.92%. Conclusion: The technique of trans-uterine artery MTX perfusion and embolization selection of close clinical could result in satisfactory treatment for tubal pregnancy. Careful selection of indication, close clinical observation and neady for any emergency should always be on alert. (authors)

Canadian Association of Gastroenterology Consensus Guidelines on Safety and Quality Indicators in Endoscopy

Directory of Open Access Journals (Sweden)

David Armstrong

2012-01-01

Full Text Available Several organizations worldwide have developed procedure-based guidelines and/or position statements regarding various aspects of quality and safety indicators, and credentialing for endoscopy. Although important, they do not specifically address patient needs or provide a framework for their adoption in the context of endoscopy services. The consensus guidelines reported in this article, however, aimed to identify processes and indicators relevant to the provision of high-quality endoscopy services that will support ongoing quality improvement across many jurisdictions, specifically in the areas of ethics, facility standards and policies, quality assurance, training and education, reporting standards and patient perceptions.

Research study about the establishment of safety culture. Effects of organizational factors in construction industry's safety indices

International Nuclear Information System (INIS)

Kojima, Mitsuhiro; Hirose, Humiko; Takano, Kenichi; Hasegawa, Naoko

1999-01-01

To find the relationships between safety related activities (such as safety patrol' or '4s/5s activities') and accidents rate in the workplace, questionnaires were sent to 965 construction companies and 120 answers were returned. In this questionnaire, safety activities, safety regulations and safety policies of the companies were asked and organizational climates, company policies, philosophies and the number of accidents in workplace were also asked. There seems some relationships between accidents rate and safety activities, safety regulations and safety policies in the companies, but the deviations between estimate values and observed values are so great that it seems impossible to estimate the accidents rate in the working place from the safety activities, safety regulations and safety policies of the companies. On the other hand, some characteristics of safety activities and organizational climates in the construction industry were identified using multi variants analysis. More detailed researches using sophisticated questionnaire will be conducted in the construction industry and petrochemical industry and relationships between the accidents rate and the safety activities will be compared between different industries. (author)

Integrated safety assessment report, Haddam Neck Plant (Docket No. 50-213): Integrated Safety Assessment Program: Draft report

International Nuclear Information System (INIS)

1987-07-01

The integrated assessment is conducted on a plant-specific basis to evaluate all licensing actions, licensee initiated plant improvements and selected unresolved generic/safety issues to establish implementation schedules for each item. Procedures allow for a periodic updating of the schedules to account for licensing issues that arise in the future. The Haddam Neck Plant is one of two plants being reviewed under the pilot program. This report indicates how 82 topics selected for review were addressed, and presents the staff's recommendations regarding the corrective actions to resolve the 82 topics and other actions to enhance plant safety. 135 refs., 4 figs., 5 tabs

RULES FOR SELECTING AND USING KEY PERFORMANCE INDICATORS FOR THE SERVICE INDUSTRY

Directory of Open Access Journals (Sweden)

Alexandra - Elena RUSĂNEANU

2014-06-01

Full Text Available There is no question that performance is the desired result of every activity or action. In order to correctly measure an organization’s performance it is necessary to select key performance indicators (KPIs that will deliver long-term value to the company. KPIs are presenting performance information for all levels of the organization and they are reflecting the progress made so far to achieve strategic objectives. The selection of the key performance indicators must be made according to the organization’s industry and activity. The company must truly understand its business and its mission. Also, KPIs must be closely linked to the strategic objectives. The focus of this research is to present effective rules for defining key performance indicators for the Service industry. This sector of economy consists in generating intangible goods like experience, expertise and information. Therefore, monitoring this type of services requires a different approach when defining performance indicators compared to the manufacturing industry.

Using and reporting the Delphi method for selecting healthcare quality indicators: a systematic review.

Science.gov (United States)

Boulkedid, Rym; Abdoul, Hendy; Loustau, Marine; Sibony, Olivier; Alberti, Corinne

2011-01-01

Delphi technique is a structured process commonly used to developed healthcare quality indicators, but there is a little recommendation for researchers who wish to use it. This study aimed 1) to describe reporting of the Delphi method to develop quality indicators, 2) to discuss specific methodological skills for quality indicators selection 3) to give guidance about this practice. Three electronic data bases were searched over a 30 years period (1978-2009). All articles that used the Delphi method to select quality indicators were identified. A standardized data extraction form was developed. Four domains (questionnaire preparation, expert panel, progress of the survey and Delphi results) were assessed. Of 80 included studies, quality of reporting varied significantly between items (9% for year's number of experience of the experts to 98% for the type of Delphi used). Reporting of methodological aspects needed to evaluate the reliability of the survey was insufficient: only 39% (31/80) of studies reported response rates for all rounds, 60% (48/80) that feedback was given between rounds, 77% (62/80) the method used to achieve consensus and 57% (48/80) listed quality indicators selected at the end of the survey. A modified Delphi procedure was used in 49/78 (63%) with a physical meeting of the panel members, usually between Delphi rounds. Median number of panel members was 17(Q1:11; Q3:31). In 40/70 (57%) studies, the panel included multiple stakeholders, who were healthcare professionals in 95% (38/40) of cases. Among 75 studies describing criteria to select quality indicators, 28 (37%) used validity and 17(23%) feasibility. The use and reporting of the Delphi method for quality indicators selection need to be improved. We provide some guidance to the investigators to improve the using and reporting of the method in future surveys.

Using and reporting the Delphi method for selecting healthcare quality indicators: a systematic review.

Directory of Open Access Journals (Sweden)

Rym Boulkedid

Full Text Available OBJECTIVE: Delphi technique is a structured process commonly used to developed healthcare quality indicators, but there is a little recommendation for researchers who wish to use it. This study aimed 1 to describe reporting of the Delphi method to develop quality indicators, 2 to discuss specific methodological skills for quality indicators selection 3 to give guidance about this practice. METHODOLOGY AND MAIN FINDING: Three electronic data bases were searched over a 30 years period (1978-2009. All articles that used the Delphi method to select quality indicators were identified. A standardized data extraction form was developed. Four domains (questionnaire preparation, expert panel, progress of the survey and Delphi results were assessed. Of 80 included studies, quality of reporting varied significantly between items (9% for year's number of experience of the experts to 98% for the type of Delphi used. Reporting of methodological aspects needed to evaluate the reliability of the survey was insufficient: only 39% (31/80 of studies reported response rates for all rounds, 60% (48/80 that feedback was given between rounds, 77% (62/80 the method used to achieve consensus and 57% (48/80 listed quality indicators selected at the end of the survey. A modified Delphi procedure was used in 49/78 (63% with a physical meeting of the panel members, usually between Delphi rounds. Median number of panel members was 17(Q1:11; Q3:31. In 40/70 (57% studies, the panel included multiple stakeholders, who were healthcare professionals in 95% (38/40 of cases. Among 75 studies describing criteria to select quality indicators, 28 (37% used validity and 17(23% feasibility. CONCLUSION: The use and reporting of the Delphi method for quality indicators selection need to be improved. We provide some guidance to the investigators to improve the using and reporting of the method in future surveys.

The natural selection of organizational and safety culture within a small to medium sized enterprise (SME).

Science.gov (United States)

Brooks, Benjamin

2008-01-01

Small to Medium Sized Enterprises (SMEs) form the majority of Australian businesses. This study uses ethnographic research methods to describe the organizational culture of a small furniture-manufacturing business in southern Australia. Results show a range of cultural assumptions variously 'embedded' within the enterprise. In line with memetics - Richard Dawkin's cultural application of Charles Darwin's theory of Evolution by Natural Selection, the author suggests that these assumptions compete to be replicated and retained within the organization. The author suggests that dominant assumptions are naturally selected, and that the selection can be better understood by considering the cultural assumptions in reference to Darwin's original principles and Frederik Barth's anthropological framework of knowledge. The results are discussed with reference to safety systems, negative cultural elements called Cultural Safety Viruses, and how our understanding of this particular organizational culture might be used to build resistance to these viruses.

Natural Elemental Concentrations and Fluxes: Their Use as Indicators of Repository Safety

Energy Technology Data Exchange (ETDEWEB)

Miller, Bill; Lind, Andy; Savage, Dave; Maul, Philip; Robinson, Peter [EnvirosQuantisci, Melton Mowbray (United Kingdom)

2002-03-01

The calculated post-closure performance of a radioactive waste repository is generally quantified in terms of radiological dose or risk to humans, with safety being determined by whether the calculated exposure values are consistent with predetermined target criteria which are deemed to represent acceptable radiological hazards. Despite their general acceptance, however, dose and risk are not perfect measures of repository safety because, in order to calculate them, gross assumptions must be made for future human behaviour patterns. Such predictions clearly become increasingly uncertain as forecasts are made further into the future. As a consequence, there has been a growing interest in developing other ways of assessing repository safety which do not require assumptions to be made for future human behaviour. One proposed assessment method is to use the distributions of naturally-occurring chemical species in the environment, expressed either as concentrations or fluxes of elements, radionuclides or radioactivity, as natural safety indicators which may be compared with the PA predictions of repository releases. Numerous comparisons are possible between the repository and natural systems. The primary objective is to use the natural system to provide context to the hazard presented by the repository releases. Put simply, if it can be demonstrated that the flux to the biosphere from the repository is not significant compared with the natural flux from the geosphere, then its radiological significance should not be of great or priority concern. Natural safety indicators may be quantified on a site specific basis, using information derived from a repository site characterisation programme, and can be compared to the outputs from the associated site specific PAs. Such calculations and comparisons may be very detailed and might examine, for example, the spatial and temporal variations in the distributions and fluxes of naturally-occurring chemical species arising from

Do daily ward interviews improve measurement of hospital quality and safety indicators? A prospective observational study.

Science.gov (United States)

Sarkies, Mitchell N; Bowles, Kelly-Ann; Skinner, Elizabeth H; Haas, Romi; Mitchell, Deb; O'Brien, Lisa; May, Kerry; Ghaly, Marcelle; Ho, Melissa; Haines, Terry P

2016-10-01

The aim of this study was to determine if the addition of daily ward interview data improves the capture of hospital quality and safety indicators compared with incident reporting systems alone. An additional aim was to determine the potential characteristics influencing under-reporting of hospital quality and safety indicators in incident reporting systems. A prospective, observational study was performed at two tertiary metropolitan public hospitals. Research assistants from allied health backgrounds met daily with the nurse in charge of the ward and discussed the occurrence of any falls, pressure injuries and rapid response medical team calls. Data were collected from four general medical wards, four surgical wards, an orthopaedic, neurosciences, plastics, respiratory, renal, sub-acute and acute medical assessment unit. An estimated total of 303 falls, 221 pressure injuries and 884 rapid response medical team calls occurred between 15 wards across two hospitals, over a period of 6 months. Hospital incident reporting systems underestimated falls by 30.0%, pressure injuries by 59.3% and rapid response medical team calls by 17.0%. The use of ward interview data collection in addition to hospital incident reporting systems improved data capture of falls by 23.8% (n = 72), pressure injuries by 21.7% (n = 48) and rapid response medical team calls by 12.7% (n = 112). Falls events were significantly less likely to be reported if they occurred on a Monday (P = 0.04) and pressure injuries significantly more likely to be reported if they occurred on a Wednesday (P = 0.01). Hospital quality and safety indicators (falls, pressure injuries and rapid response medical team calls) were under-reported in incident reporting systems, with variability in under-reporting between wards and the day of event occurrence. The use of ward interview data collection in addition to hospital incident reporting systems improved reporting of hospital quality and safety

Multiperiod Telser’s Safety-First Portfolio Selection with Regime Switching

Directory of Open Access Journals (Sweden)

Chuangwei Lin

2018-01-01

Full Text Available This paper investigates a multiperiod Telser’s safety-first portfolio selection model with regime switching where the returns of the assets are assumed to depend on the market states modulated by a discrete-time Markov chain. The investor aims to maximize the expected terminal wealth and does not want the probability of the terminal wealth to fall short of a disaster level to exceed a predetermined number called the risk control level. Referring to Tchebycheff inequality, we modify Telser’s safety-first model to the case that aims to maximize the expected terminal wealth subject to a constraint where the upper bound of the disaster probability is less than the risk control level. By the Lagrange multiplier technique and the embedding method, we study in detail the existence of the optimal strategy and derive the closed-form optimal strategy. Finally, by mathematical and numerical analysis, we analyze the effects of the disaster level, the risk control level, the transition matrix of the Markov chain, the expected excess return, and the variance of the risky return.

DEVELOPMENT AND EVALUATION OF A SELECTIVE AND INDICATIVE MEDIUM FOR ISOLATION OF ACTINOBACILLUS-PLEUROPNEUMONIAE FROM TONSILS

DEFF Research Database (Denmark)

Jakobsen, Marianne; Nielsen, Jens

1995-01-01

In order to isolate ActinobacillIus pleuropneumoniae from mixed bacterial flora a selective and indicative medium was developed. The optimal concentrations of antibiotics were determined for selective chocolate agar (S-TSA) and selective blood agar (S-MBA) using a set of 25 strains of A. pleuropn......In order to isolate ActinobacillIus pleuropneumoniae from mixed bacterial flora a selective and indicative medium was developed. The optimal concentrations of antibiotics were determined for selective chocolate agar (S-TSA) and selective blood agar (S-MBA) using a set of 25 strains of A...

Optimization of safety equipment outages improves safety

International Nuclear Information System (INIS)

Cepin, Marko

2002-01-01

Testing and maintenance activities of safety equipment in nuclear power plants are an important potential for risk and cost reduction. An optimization method is presented based on the simulated annealing algorithm. The method determines the optimal schedule of safety equipment outages due to testing and maintenance based on minimization of selected risk measure. The mean value of the selected time dependent risk measure represents the objective function of the optimization. The time dependent function of the selected risk measure is obtained from probabilistic safety assessment, i.e. the fault tree analysis at the system level and the fault tree/event tree analysis at the plant level, both extended with inclusion of time requirements. Results of several examples showed that it is possible to reduce risk by application of the proposed method. Because of large uncertainties in the probabilistic safety assessment, the most important result of the method may not be a selection of the most suitable schedule of safety equipment outages among those, which results in similarly low risk. But, it may be a prevention of such schedules of safety equipment outages, which result in high risk. Such finding increases the importance of evaluation speed versus the requirement of getting always the global optimum no matter if it is only slightly better that certain local one

The use of safety indicators, complementary to dose and risk, in the assessment of radioactive waste disposal

International Nuclear Information System (INIS)

Gera, F.; Vovk, I.; Wingefors, S.

1998-01-01

The use of safety indicators, other than dose and risk, to complement the safety assessment of disposal systems for radioactive waste, is not a new idea. Several possible approaches have been proposed through the years, including a discussion in an IAEA document of 1994. The present paper reviews critically the various proposed indicators, identifies the most promising ones and suggests a possible approach for the assessment of their viability. In particular it suggests that a Coordinated Research Project should be organized with the main objectives of assembling, reviewing and generating the necessary scientific information on natural values, particularly fluxes and concentrations of pollutants, and on their impacts on public health and environmental quality. (author)

The development and evaluation of programmatic performance indicators associated with maintenance at nuclear power plants

International Nuclear Information System (INIS)

Wreathall, J.; Fragola, J.; Appignani, P.; Burlile, G.; Shen, Y.

1990-05-01

This report summarizes the development and evaluation of programmatic performance indicators of maintenance. These indicators were selected by: (1) creating a formal framework of plant processes; (2) identifying features of plant behavior considered important to safety; (3) evaluating existing indicators against these features; and (4) performing statistical analyses for the selected indicators. The report recommends additional testing. This document provides the appendices to the report. These appendices are: synopsis of process model; detailed results of statistical analysis; and signal processing analysis of daily power loss indicator

Selecting environmental indicator for use in strategic environmental assessment

International Nuclear Information System (INIS)

Donnelly, Alison; Jones, Mike; O'Mahony, Tadhg; Byrne, Gerry

2007-01-01

The primary aim of carrying out Strategic Environmental Assessment (SEA) is to provide for a high level of environmental protection and to integrate environmental considerations into the planning process. The SEA Directive (2001/42/EC) recommends monitoring to determine the environmental impact of the implementation of plans and programmes. Environmental indicators are a useful tool by which this impact may be measured. However, careful consideration must be given to developing a set of indicators in order to isolate, plan or programme specific impacts. Here, we demonstrate the effectiveness of a workshop-based approach to develop appropriate criteria for selecting environmental indicator for use in SEA. A multi-disciplinary team was used in the approach which consisted of representatives from each of four environmental fields i.e. biodiversity, water, air and climatic factors, together with SEA experts, planning experts, academics and consultants. The team reviewed various sets of criteria, already in existence, for environmental indicator development but not specifically for SEA indicators. The results of this review together with original criteria were applied to the final list agreed upon. Some of the criteria recommended includes, relevance to plan, ability to prioritise, and ability to identify conflict with other plan or SEA objectives

Indicators for traffic safety assessment and prediction and their application in micro-simulation modelling : a study of urban and suburban intersections

OpenAIRE

Archer, Jeffery

2005-01-01

In order to achieve sustainable long-term transport infrastructure development, there is a growing need for fast, reliable and effective methods to evaluate and predict the impact of traffic safety measures. Recognising this need, and the need for an active traffic safety approach, this thesis focuses on traffic safety assessment and prediction based on the use of safety indicators that measure the spatial and/or temporal proximity of safety critical events. The main advantage of such measure...

RA-6 reactor's probabilistic safety evaluation. Identification and selection of starting events

International Nuclear Information System (INIS)

Kay, J.; Chiossi, C.; Felizia, E.; Vallerga, H.; Kalejman, G.; Navarro, R.; Caruso, G.J.

1987-01-01

A summary of the 'Identification and selection of starting events' stage of the previous probabilistic safety evaluation of RA-6 reactor is presented. This evaluation was performed to verify if the safety criteria required for the licensing of RA-6 are met and to promote the diffusion of its meaning and usefulness with educational purposes. At this stage the starting events of RA-6 are determined and the probability that such events occur is calculated. The identification and selection of starting events is performed in two steps: determination of proposed starting events and determination of postulated starting events. The proposed starting events are determined by means of the master logic diagram (MLD) method, while the postulated starting events are obtained by grouping the proposed starting events. The simplifying hypothesis required for the application of MLD to the reactor are also formulated. The probability that the proposed and postulated starting events occur is afterwards calculated, adopting different fault models, in accordance with the nature of events that are considered. Conservative hypothesis on the characteristics of these events and the uncertainty of parameter values of those models are also formulated. The numerical values of the above mentioned probabilities are obtained by giving the parameters suitable values that are extracted from specialized publications. (Author)

Evaluation of the Quality of Occupational Health and Safety Management Systems Based on Key Performance Indicators in Certified Organizations.

Science.gov (United States)

Mohammadfam, Iraj; Kamalinia, Mojtaba; Momeni, Mansour; Golmohammadi, Rostam; Hamidi, Yadollah; Soltanian, Alireza

2017-06-01

Occupational Health and Safety Management Systems are becoming more widespread in organizations. Consequently, their effectiveness has become a core topic for researchers. This paper evaluates the performance of the Occupational Health and Safety Assessment Series 18001 specification in certified companies in Iran. The evaluation is based on a comparison of specific criteria and indictors related to occupational health and safety management practices in three certified and three noncertified companies. Findings indicate that the performance of certified companies with respect to occupational health and safety management practices is significantly better than that of noncertified companies. Occupational Health and Safety Assessment Series 18001-certified companies have a better level of occupational health and safety; this supports the argument that Occupational Health and Safety Management Systems play an important strategic role in health and safety in the workplace.

Ratios performance indicator evaluation of selected engineering enterprises in the northeast cohesion region

OpenAIRE

Šenec, Alexandr

2014-01-01

The paper deals with the performance indicator evaluation of selected industrial companies with a predominance of engineering production. Ratio indicators were used in order to measure business performance per unit of fixed assets and per employee. Analyzed data were obtained from companies annual reports. Trends ratio indicators were intended with the help of mathematical and statistical methods. These ratios indicator assessing the level of performance, value added and operating profit p...

Selection of IFE target materials from a safety and environmental perspective

Science.gov (United States)

Latkowski, J. F.; Sanz, J.; Reyes, S.; Gomez del Rio, J.

2001-05-01

Target materials for inertial fusion energy (IFE) power plant designs might be selected for a wide variety of reasons including wall absorption of driver energy, material opacity, cost and ease of fabrication. While each of these issues are of great importance, target materials should also be selected based upon their safety and environmental (S&E) characteristics. The present work focuses on the recycling, waste management and accident dose characteristics of potential target materials. If target materials are recycled so that the quantity is small, isotopic separation may be economically viable. Therefore, calculations have been completed for all stable isotopes for all elements from lithium to polonium. The results of these calculations are used to identify specific isotopes and elements that are most likely to be offensive as well as those most likely to be acceptable in terms of their S&E characteristics.

Expert study to select indicators of the occurrence of emerging mycotoxin hazards.

Science.gov (United States)

Kandhai, M C; Booij, C J H; Van der Fels-Klerx, H J

2011-01-01

This article describes a Delphi-based expert judgment study aimed at the selection of indicators to identify the occurrence of emerging mycotoxin hazards related to Fusarium spp. in wheat supply chains. A panel of 29 experts from 12 European countries followed a holistic approach to evaluate the most important indicators for different chain stages (growth, transport and storage, and processing) and their relative importance. After three e-mailing rounds, the experts reached consensus on the most important indicators for each of the three stages: wheat growth, transport and storage, and processing. For wheat growth, these indicators include: relative humidity/rainfall, crop rotation, temperature, tillage practice, water activity of the kernels, and crop variety/cultivar. For the transport and storage stage, they include water activity in the kernels, relative humidity, ventilation, temperature, storage capacity, and logistics. For wheat processing, indicators include quality data, fraction of the cereal used, water activity in the kernels, quality management and traceability systems, and carryover of contamination. The indicators selected in this study can be used in an identification system for the occurrence of emerging mycotoxin hazards in wheat supply chains. Such a system can be used by risk managers within governmental (related) organizations and/or the food and feed industry in order to react proactively to the occurrence of these emerging mycotoxins. © 2010 Society for Risk Analysis.

Methodological development for selection of significant predictors explaining fatal road accidents.

Science.gov (United States)

Dadashova, Bahar; Arenas-Ramírez, Blanca; Mira-McWilliams, José; Aparicio-Izquierdo, Francisco

2016-05-01

Identification of the most relevant factors for explaining road accident occurrence is an important issue in road safety research, particularly for future decision-making processes in transport policy. However model selection for this particular purpose is still an ongoing research. In this paper we propose a methodological development for model selection which addresses both explanatory variable and adequate model selection issues. A variable selection procedure, TIM (two-input model) method is carried out by combining neural network design and statistical approaches. The error structure of the fitted model is assumed to follow an autoregressive process. All models are estimated using Markov Chain Monte Carlo method where the model parameters are assigned non-informative prior distributions. The final model is built using the results of the variable selection. For the application of the proposed methodology the number of fatal accidents in Spain during 2000-2011 was used. This indicator has experienced the maximum reduction internationally during the indicated years thus making it an interesting time series from a road safety policy perspective. Hence the identification of the variables that have affected this reduction is of particular interest for future decision making. The results of the variable selection process show that the selected variables are main subjects of road safety policy measures. Published by Elsevier Ltd.

Healthcare waste management practices and safety indicators in Nigeria.

Science.gov (United States)

Oyekale, Abayomi Samuel; Oyekale, Tolulope Olayemi

2017-09-25

Adequate management of healthcare waste (HCW) is a prerequisite for efficient delivery of healthcare services. In Nigeria, there are several constraints militating against proper management of HCW. This is raising some environmental concerns among stakeholders in the health sector. In this study, we analyzed the practices of HCW management and determinants of risky/safe indices of HCW disposal. The study used the 2013/2014 Service Delivery Indicator (SDI) data that were collected from 2480 healthcare facilities in Nigeria. Descriptive statistics, Principal Component Analysis (PCA) and Ordinary Least Square (OLS) regression were used to analyze the data. The results showed that 52.20% and 38.21% of the sampled healthcare facilities from Cross River and Bauchi states possessed guidelines for HCW management, respectively. Trainings on management of HCW were attended by 67.18% and 53.19% of the healthcare facilities from Cross River and Imo states, respectively. Also, 32.32% and 29.50% of healthcare facilities from rural and urban areas previously sent some of their staff members for trainings on HCW management, respectively. Sharp and non-sharp HCW were burnt in protected pits in 45.40% and 45.36% of all the sampled healthcare facilities, respectively. Incinerators were reported to be functional in only 2.06% of the total healthcare facilities. In Bauchi and Kebbi states, 23.58% and 21.05% of the healthcare facilities respectively burnt sharp HCW without any protection. Using PCA, computed risky indices for disposal of sharp HCW were highest in Bayelsa state (0.3070) and Kebbi state (0.2172), while indices of risky disposal of non-sharp HCW were highest in Bayelsa state (0.2868) and Osun state (0.2652). The OLS results showed that at 5% level of significance, possession of medical waste disposal guidelines, staff trainings on HCW management, traveling hours from the facilities to local headquarters and being located in rural areas significantly influenced indices of

Healthcare waste management practices and safety indicators in Nigeria

Directory of Open Access Journals (Sweden)

Abayomi Samuel Oyekale

2017-09-01

rural areas significantly influenced indices of risky/safe medical waste disposal (p < 0.05. Conclusion The study concluded that there was low compliance with standard HCW management. It was recommended that possession of HCW management guidelines, staff training on HCW disposal and provision of requisite equipment for proper treatment of HCW would promote environmental safety in HCW disposal.

Leading product-related environmental performance indicators: a selection guide and database

DEFF Research Database (Denmark)

Issa, Isabela I.; Pigosso, Daniela Cristina Antelmi; McAloone, Tim C.

2015-01-01

Ecodesign is a proactive environmental management and improvement approach employed in the product development process, which aims to minimize the environmental impacts caused during a product's life cycle and thus improve its environmental performance. The establishment of measurable environmental...... in the selection and application of environmental performance indicators - a more structured approach is still lacking. This paper presents the efforts made to identify and systematize existing leading product-related environmental performance indicators, based on a systematic literature review, and to develop...

Effectiveness evaluation methodology for safety processes to enhance organisational culture in hazardous installations

International Nuclear Information System (INIS)

Mengolini, A.; Debarberis, L.

2008-01-01

Safety performance indicators are widely collected and used in hazardous installations. The IAEA, OECD and other international organisations have developed approaches that strongly promote deployment of safety performance indicators. These indicators focus mainly on operational performance, but some of them also address organisational and safety culture aspects. However, operators of hazardous installations, in particular those with limited resources and time constraints, often find it difficult to collect the large number of different safety performance indicators. Moreover, they also have difficulties with giving a meaning to the numbers and trends recorded, especially to those that should reflect a positive safety culture. In this light, the aim of this article is to address the need to monitor and assess progress on implementation of a programme to enhance safety and organisational culture. It proposes a specific process-view approach to effectiveness evaluation of organisational and safety culture indicators by means of a multi-level system in which safety processes and staff involvement in defining improvement activities are central. In this way safety becomes fully embedded in staff activities. Key members of personnel become directly involved in identifying and supplying leading indicators relating to their own daily activity and become responsible and accountable for keeping the measurement system alive. Besides use of lagging indicators, particular emphasis is placed on the importance of identifying and selecting leading indicators which can be used to drive safety performance for organisational and safety culture aspects as well

Effectiveness evaluation methodology for safety processes to enhance organisational culture in hazardous installations.

Science.gov (United States)

Mengolini, A; Debarberis, L

2008-06-30

Safety performance indicators are widely collected and used in hazardous installations. The IAEA, OECD and other international organisations have developed approaches that strongly promote deployment of safety performance indicators. These indicators focus mainly on operational performance, but some of them also address organisational and safety culture aspects. However, operators of hazardous installations, in particular those with limited resources and time constraints, often find it difficult to collect the large number of different safety performance indicators. Moreover, they also have difficulties with giving a meaning to the numbers and trends recorded, especially to those that should reflect a positive safety culture. In this light, the aim of this article is to address the need to monitor and assess progress on implementation of a programme to enhance safety and organisational culture. It proposes a specific process-view approach to effectiveness evaluation of organisational and safety culture indicators by means of a multi-level system in which safety processes and staff involvement in defining improvement activities are central. In this way safety becomes fully embedded in staff activities. Key members of personnel become directly involved in identifying and supplying leading indicators relating to their own daily activity and become responsible and accountable for keeping the measurement system alive. Besides use of lagging indicators, particular emphasis is placed on the importance of identifying and selecting leading indicators which can be used to drive safety performance for organisational and safety culture aspects as well.

Are long physician working hours harmful to patient safety?

Science.gov (United States)

Ehara, Akira

2008-04-01

Pediatricians of Japanese hospitals including not only residents but also attending physicians work long hours, and 8% work for >79 h per week. Most of them work consecutively for >or=32 h when they are on call. The aim of the present study was to evaluate the effect of long work hours on patient safety. The electronic databases MEDLINE and EMBASE to searched identify the English- and Japanese-language literature for studies on work hours, medical errors, patient safety, and malpractice for years 1966-2005. Studies that analyzed the relationship between physician work hours and outcomes directly related to patient safety were selected. Seven studies met the criteria. Four studies suggest that reduction of work hours has a favorable effect on patient safety indicators. In the other three studies no significant changes of the indicators were observed, but no report found that shorter work hours were harmful to patient safety. Decrease of physician work hours is not harmful but favorable to patient safety.

Prediction of genetic gains by selection indices using mixed models in elephant grass for energy purposes.

Science.gov (United States)

Silva, V B; Daher, R F; Araújo, M S B; Souza, Y P; Cassaro, S; Menezes, B R S; Gravina, L M; Novo, A A C; Tardin, F D; Júnior, A T Amaral

2017-09-27

Genetically improved cultivars of elephant grass need to be adapted to different ecosystems with a faster growth speed and lower seasonality of biomass production over the year. This study aimed to use selection indices using mixed models (REML/BLUP) for selecting families and progenies within full-sib families of elephant grass (Pennisetum purpureum) for biomass production. One hundred and twenty full-sib progenies were assessed from 2014 to 2015 in a randomized block design with three replications. During this period, the traits dry matter production, the number of tillers, plant height, stem diameter, and neutral detergent fiber were assessed. Families 3 and 1 were the best classified, being the most indicated for selection effect. Progenies 40, 45, 46, and 49 got the first positions in the three indices assessed in the first cut. The gain for individual 40 was 161.76% using Mulamba and Mock index. The use of selection indices using mixed models is advantageous in elephant grass since they provide high gains with the selection, which are distributed among all the assessed traits in the most appropriate situation to breeding programs.

Indicators of Nuclear safety and exploitation in ANAV; Indicadores de Seguridad Nuclear y explotacion en ANAV

Energy Technology Data Exchange (ETDEWEB)

Quintana Prieto, M.; Jorda Alcove, M.

2013-07-01

The use of indicators by ANAV plants, aims to be a tool to facilitate the assessment of the behaviour of the plants nuclear over a specific time period. The following are and are they explain those related to Nuclear safety and exploitation.

Automatic selection of indicators in a fully saturated regression

DEFF Research Database (Denmark)

Hendry, David F.; Johansen, Søren; Santos, Carlos

2008-01-01

We consider selecting a regression model, using a variant of Gets, when there are more variables than observations, in the special case that the variables are impulse dummies (indicators) for every observation. We show that the setting is unproblematic if tackled appropriately, and obtain the fin...... the finite-sample distribution of estimators of the mean and variance in a simple location-scale model under the null that no impulses matter. A Monte Carlo simulation confirms the null distribution, and shows power against an alternative of interest....

Trace analysis of cyanide by ion-selective electrode indicator technique

International Nuclear Information System (INIS)

Tom, R.L.; Kapauan, P.A.

1977-01-01

Due to the toxicity of cyanide, its analysis in water is important. The use of ion-selective electrodes for its determination was studied. The known addition method using a silver sulfide membrane electrode was studied. This involved using a silver indicator solution to determine the cyanide content of a sample. Known amounts of a standard cyanide solution were added and the potentials noted. The results were plotted and the original concentration of cyanide extrapolated. The results of the experiment indicated the method to be practical for analysis of industrial waste waters, even in the presence of metal ions. The metal ions were masked using an EDTA solution while possible sulfides were precipitated out using a Pb (N0 3 ) 2 solution. The method was tested on four actual samples and the results indicated the applicability of the method

Exposure data and risk indicators for safety performance assessment in Europe.

Science.gov (United States)

Papadimitriou, Eleonora; Yannis, George; Bijleveld, Frits; Cardoso, João L

2013-11-01

The objective of this paper is the analysis of the state-of-the-art in risk indicators and exposure data for safety performance assessment in Europe, in terms of data availability, collection methodologies and use. More specifically, the concepts of exposure and risk are explored, as well as the theoretical properties of various exposure measures used in road safety research (e.g. vehicle- and person-kilometres of travel, vehicle fleet, road length, driver population, time spent in traffic, etc.). Moreover, the existing methods for collecting disaggregate exposure data for risk estimates at national level are presented and assessed, including survey methods (e.g. travel surveys, traffic counts) and databases (e.g. national registers). A detailed analysis of the availability and quality of existing risk exposure data is also carried out. More specifically, the results of a questionnaire survey in the European countries are presented, with detailed information on exposure measures available, their possible disaggregations (i.e. variables and values), their conformity to standard definitions and the characteristics of their national collection methods. Finally, the potential of international risk comparisons is investigated, mainly through the International Data Files with exposure data (e.g. Eurostat, IRTAD, ECMT, UNECE, IRF, etc.). The results of this review confirm that comparing risk rates at international level may be a complex task, as the availability and quality of exposure estimates in European countries varies significantly. The lack of a common framework for the collection and exploitation of exposure data limits significantly the comparability of the national data. On the other hand, the International Data Files containing exposure data provide useful statistics and estimates in a systematic way and are currently the only sources allowing international comparisons of road safety performance under certain conditions. Copyright © 2013 Elsevier Ltd. All

Review of EU-APR Design for Selected Safety Issues of WERNA RHWG 2013

Energy Technology Data Exchange (ETDEWEB)

Kim, Yong Soo; Kim, Ji Hwan [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

Western European Nuclear Regulators' Association (WENRA) was established in 1999 to develop a harmonized approach to nuclear safety and radiation protection and their regulation. In 2013, the Reactor Harmonization Working Group (RHWG) of WENRA sets out the common positions on the seven selected key safety issues. This paper is to introduce the regulatory positions of WENRA RHWG 2013 and to review the compliance of the EU-APR with them. In this paper, we reviewed the compliance of the EUAPR regarding seven safety issues for new NPPs presented by WERNA RHWG in 2013. The EU-APR design fully complies with all WERNA RHWG safety issues since the following measures have been incorporated in it: - Successive five levels of DiD maintaining independence between different levels of DiD - Diverse design against multiple failure events such as ATWS, SBO, Loss of Ultimate Heat Sink, and Loss of Spent Fuel Pool Cooling - SAs dedicated mitigation systems to ensure the containment integrity during the SAs. - Practically eliminates accident sequences with a large or early release of radiological materials by diverse designs for multiple failure events, SAs dedicated mitigation system, and double containment design - Standard site parameters not lead to core melt accidents due to natural or man-made external hazards.

Exploration and safety evaluations of salt formations and site selection procedures; Erkundung und Sicherheitsbewertung von Salzformationen und Standortauswahlverfahren

Energy Technology Data Exchange (ETDEWEB)

Krapf, Eva Barbara

2016-12-12

In 2011 the final decision for the withdrawal from the nuclear energy program was decided in the Federal Republic of Germany. The majority of the produced radioactive waste originate in the operation as well as in the decommissioning and dismantling of nuclear facilities. The long-term containment of especially heat-developing and high-level waste in an underground disposal facility is pursued. The Site Selection Act (StandAG), passed in 2013, defined further procedural steps as well as responsibilities and the way of public participation during the site selection. In this context the newly founded Commission Storage of Highly Radioactive Waste was assigned with the task of giving relevant recommendations based on their investigation of specific aspects and fundamental questions. The objective of this procedure is the selection of the site that can provide the best possible safety for humans and the environment during the defined period of one million years. The Commissions' final report was published in July 2016. In this thesis a possible approach for exploring sites in connection with safety investigations is recommended. The site selection procedure described in the StandAG represents the basis for the considerations. Geoscientific exclusion criteria, minimum requirements as well as weighing criteria can be developed regarding the relevant geoscientific and climatic changes during the defined period of one million years. In contrast to the recommendations made by the Commission Storage of Highly Radioactive Waste no previously existing report has been revised and adapted. Rather, all issues relevant for the long-term containment of radioactive waste in a disposal facility had been newly developed. The considerations are related to salt domes as host rock. Furthermore, according to the StandAG preliminary safety investigations are required in every step of the site selection. The recommendations made in this thesis concerning content and feasibility of

The use of uranium fluxes as safety indicators of radioactive waste repositories

International Nuclear Information System (INIS)

Miller, W.M.; Hooker, P.J.

2002-01-01

Natural analogues based on uranium deposits are commonly used to represent the long-term behaviour of radioactive waste repositories or the processes that influence their radioactive contents. The geochemical dispersion of naturally occurring uranium can also be used to model natural radioactivity fluxes in the vicinity of a planned repository. These fluxes can be estimated for erosional and groundwater discharge processes and compared with calculated future fluxes of radioactivity that would be released from a repository. The methodology is outlined and the benefits of the approach for supporting the derivation of a safety case for a repository are indicated. (author)

Development of safety assessment of nuclear power plants using indicators; Ydinvoimalaitosten turvallisuuden arvioinnin kehittaeminen tunnuslukujen avulla

Energy Technology Data Exchange (ETDEWEB)

Tiippana, P.

1997-11-01

The study is based on an indicator system which is under development at the Radiation and Nuclear Safety Authority (STUK). The goal of this study was to define and develop both PSA-based indicators and indicators from failure statistics. As PSA-based indicators the possibility was studied to define and express the risk importance of exemptions from the Technical Specifications, failures, preventive maintenance and other disconnections of devices covered by the Technical Specifications, operating events covered by Guide YVL 1.5 and plant modifications. In this piece of research the applicability of plant specific living PSA-models used for calculation of indicators was examined. The research included both Loviisa and Olkiluoto nuclear power plants in Finland. 47 refs.

Implementation of child safety and health management system by means of FMEA method

Directory of Open Access Journals (Sweden)

B. Akbari Neisiani

2016-01-01

Full Text Available Every year, many accidents leading to physical injuries in kindergartens, indicates that a very large percentage of them are related to the safety concerns and lack of hygiene in these places. Families, due to their busy life style and working hours and also children needs of preschool education, are searching to find most suitable kindergartens for their children. Selecting a kindergarten with various suitable training programs, although very important criteria for selection, but is not sufficient. Indicators such as health, safety and environment issues in these places must be crucial factors in this decision making. Child safety and health management system is an integrated system, derived from health, safety and environmental management regulations which helps the kindergartens complies with relevant regulations to reduce the number of accidents occurrence. The present case study has tried, by using failure modes and effects analysis method and child safety and health management system to find the best practicable indicators to assess the relative impact of different failures in order to identify the parts of the process that are most in need of change. In this regards, 10 semi-governmental kindergartens located in Tehran District 6 of Tehran Municipality, which are supervised by municipality of Tehran were selected and evaluated. The results showed that according to the child safety and health management system and failure modes and effects analysis, all these places need massive infrastructural changes according to the preventive action list in order to be considered a safe and hygienic place for the children.

Study of indicators aggregation techniques for the selection of a new nuclear reactor for Mexico

International Nuclear Information System (INIS)

Barragan M, A.M.; Martin del Campo M, C.

2007-01-01

A study on several aggregation techniques that can be used as multi criteria analysis methods, like important part of the methodology developed for the selection of a nuclear reactor for Mexico is described. In an arbitrary way three reactors were selected to be compared, these they are the AP1000 (Advance Passive from 1000 MWe), the PBMR (Pebble Bed Modular Reactor) and the GT-MHR (Gas Turbine Modular Helium). The evaluation approaches were classified in three categories: Economic, Socio-political and of safety and environment. In each category they were defined the more important evaluation indicators and then it was built a matrix with those values of each reactor. The four studied aggregation methods are described: Normalization, Linear deliberation, Fuzzy Logic and AHP (Analytic Hierarchy Process). The well-known aggregation mechanisms are those that are obtained of the lineal deliberation and of the normalization, which have demonstrated to give good results before the simplicity of their use. The fuzzy logic has the advantage that it allows to manage qualitative and quantitative information simultaneously without the aggregation problems that are presented since in a conventional system the semantic pattern on that is based, it is provided by the theory of the diffuse groups that has demonstrated in other areas of the knowledge a better approach to the reality, when admitting that the nature has shades and that the decisions take in function of a wide range of possibilities and of approaches in contradictory occasions or in conflict, all equally worth. The Analytic Hierarchical Process (AHP) that consists in formalizing the intuitive understanding of a multi criteria complex problem, by means of the construction of a hierarchical model that allows the decision agent to structure the problem in visual form, giving him the form of a hierarchy of attributes (global objective of the problem, approaches and alternative). Finally, using the matrix of initiators

Selection of IFE target materials from a safety and environmental perspective

Energy Technology Data Exchange (ETDEWEB)

Latkowski, J.F. E-mail: latkowski1@llnl.gov; Sanz, J.; Reyes, S.; Gomez del Rio, J

2001-05-21

Target materials for inertial fusion energy (IFE) power plant designs might be selected for a wide variety of reasons including wall absorption of driver energy, material opacity, cost and ease of fabrication. While each of these issues are of great importance, target materials should also be selected based upon their safety and environmental (S and E) characteristics. The present work focuses on the recycling, waste management and accident dose characteristics of potential target materials. If target materials are recycled so that the quantity is small, isotopic separation may be economically viable. Therefore, calculations have been completed for all stable isotopes for all elements from lithium to polonium. The results of these calculations are used to identify specific isotopes and elements that are most likely to be offensive as well as those most likely to be acceptable in terms of their S and E characteristics.

Metholology for the selection of LWR safety R and D projects. Phase I, status report

International Nuclear Information System (INIS)

El-Sheikh, K.A.

1980-03-01

The objective of the LWR R and D Selection Methodology Program is to develop and demonstrate an R and D selection methodology appropriate for LWR safety technology. This report documents the development work from the program beginning in April, 1979 to the end of Fiscal Year 1979. The scope of work for this period included three tasks; methodology review (Task 1), measures development (Task 2), and methodology development for the first phase of application (Task 3). The accomplishments of these tasks are presented

Self-Selection Patterns of College Roommates as Identified by the Myers-Briggs Type Indicator.

Science.gov (United States)

Anchors, W. Scott; Hale, John, Jr.

1985-01-01

Investigated patterns and processes by which students (N=422) made unassisted roommate pairings within residence halls using the Myers-Briggs Type Indicator. Results indicated introverts, intuitives, feelers, and perceivers each tended to self-select. (BL)

A comparison of leading and lagging indicators of safety in naval aviation.

Science.gov (United States)

O'Connor, Paul; Cowan, Shawn; Alton, Jeffrey

2010-07-01

The purpose of this paper is to examine the results of two different methods of identifying human factors safety concerns in U.S. Naval aviation. In both studies, the information was collected using the Department of Defense Human Factors Analysis and Classification System (DoD-HFACS). In the first study, aviation mishap data (a lagging indictor) was obtained on 47 F/A-18 and 16 H-60 mishaps. In the second study, the responses of 68 squadrons to a survey regarding the human factors issues that they considered to be of the greatest safety concern were examined (a leading indicator). First study results revealed that skill-based errors were the most commonly cited factors for both F/A-18 and H-60 mishaps (70.2% and 81.3%, respectively). More specifically, the most commonly used nanocodes were 'over control/ under control' (27.7% and 56.3%, respectively), 'breakdown in visual scan' (27.7% and 12.5%, respectively), and 'procedural errors' (23.4% and 37.6%, respectively). The second study identified that the main concern of F/A-18 and H-60 aviators was workload and operational tempo (identified by 85% of squadrons). It can be concluded that the nanocodes that were most commonly used to classify the causes of past mishaps were not identified as major concerns by the squadrons who responded to the survey. The findings from these studies emphasize the importance of examining a number of performance metrics to ensure that effective measures are being taken to improve safety.

The selection of probabilistic safety assessment techniques for non-reactor nuclear facilities

International Nuclear Information System (INIS)

Vail, J.

1992-01-01

Historically, the probabilistic safety assessment (PSA) methodology of choice is the well known event tree/fault tree inductive technique. For reactor facilities is has stood the test of time. Some non-reactor nuclear facilities have found inductive methodologies difficult to apply. The stand-alone fault tree deductive technique has been used effectively to analyze risk in nuclear chemical processing facilities and waste handling facilities. The selection between the two choices suggest benefits from use of the deductive method for non-reactor facilities

Performance indicators for power reactors

International Nuclear Information System (INIS)

Gillies, C.; White, M.

1995-11-01

A review of Canadian and worldwide performance indicator definitions and data was performed to identify a set of indicators that could be used for comparison of performance among nuclear power plants. The results of this review are to be used as input to an AECB team developing a consistent set of performance indicators for measuring Canadian power reactor safety performance. To support the identification of performance indicators, a set of criteria was developed to assess the effectiveness of each indicator for meaningful comparison of performance information. The project identified a recommended set of performance indicators that could be used by AECB staff to compare the performance of Canadian nuclear power plants among themselves, and with international performance. The basis for selection of the recommended set and exclusion of others is provided. This report provides definitions and calculation methods for each recommended performance indicator. In addition, a spreadsheet has been developed for comparison and trending for the recommended set of indicators. Example trend graphs are included to demonstrate the use of the spreadsheet. (author). 50 refs., 11 tabs., 3 figs

On Optimum Safety Levels of Breakwaters

DEFF Research Database (Denmark)

Burcharth, Hans F.; Sørensen, John Dalsgaard

2006-01-01

The paper presents results from numerical simulations performed with the objective of identifying optimum design safety levels of conventional rubble mound and caisson breakwaters, corresponding to the lowest costs over the service life of the structures. The work is related to the PIANC Working...... Group 47 on "Selection of type of breakwater structures". The paper summaries results given in Burcharth and Sorensen (2005) related to outer rubble mound breakwaters but focus on optimum safety levels for outer caisson breakwaters on low and high rubble foundations placed on sea beds strong enough...... to resist geotechnical slip failures. Optimum safety levels formulated for use both in deterministic and probabilistic design procedures are given. Results obtained so far indicate that the optimum safety levels for caisson breakwaters are much higher than for rubble mound breakwaters....

Using Harm-Based Weights for the AHRQ Patient Safety for Selected Indicators Composite (PSI-90): Does It Affect Assessment of Hospital Performance and Financial Penalties in Veterans Health Administration Hospitals?

Science.gov (United States)

Chen, Qi; Rosen, Amy K; Borzecki, Ann; Shwartz, Michael

2016-12-01

To assess whether hospital profiles for public reporting and pay-for-performance, measured by the Agency for Healthcare Research and Quality (AHRQ) Patient Safety for Selected Indicators (PSI-90) composite measure, were affected by using the recently developed harm-based weights. Retrospective analysis of 2012-2014 data from the Veterans Health Administration (VA). The AHRQ PSI software (v5.0) was applied to obtain the original volume-based PSI-90 scores for 132 acute-care hospitals. We constructed a modified PSI-90 using the harm-based weights developed by AHRQ. We compared hospital profiles for public reporting and pay-for-performance between these two PSI-90s and assessed patterns in these changes. The volume-based and the harm-based PSI-90s were strongly correlated (r = 0.67, p hospitals changed categorization), but it had a much larger impact on pay-for-performance (e.g., 15 percent of hospitals would have faced different financial penalties under the Medicare Hospital-Acquired Condition Reduction Program). Because of changes in weights of specific PSIs, hospital profile changes occurred systematically. Use of the harm-based weights in PSI-90 has the potential to significantly change payments under pay-for-performance programs. Policy makers should carefully develop transition plans for guiding hospitals through changes in any quality metrics used for pay-for-performance. © Health Research and Educational Trust.

Safety KPIs - Monitoring of safety performance

Directory of Open Access Journals (Sweden)

Andrej Lališ

2014-09-01

Full Text Available This paper aims to provide brief overview of aviation safety development focusing on modern trends represented by implementation of Safety Key Performance Indicators. Even though aviation is perceived as safe means of transport, it is still struggling with its complexity given by long-term growth and robustness which it has reached today. Thus nowadays safety issues are much more complex and harder to handle than ever before. We are more and more concerned about organizational factors and control mechanisms which have potential to further increase level of aviation safety. Within this paper we will not only introduce the concept of Key Performance Indicators in area of aviation safety as an efficient control mechanism, but also analyse available legislation and documentation. Finally we will propose complex set of indicators which could be applied to Czech Air Navigation Service Provider.

Geriatric Patient Safety Indicators Based on Linked Administrative Health Data to Assess Anticoagulant-Related Thromboembolic and Hemorrhagic Adverse Events in Older Inpatients: A Study Proposal.

Science.gov (United States)

Le Pogam, Marie-Annick; Quantin, Catherine; Reich, Oliver; Tuppin, Philippe; Fagot-Campagna, Anne; Paccaud, Fred; Peytremann-Bridevaux, Isabelle; Burnand, Bernard

2017-05-11

Frail older people with multiple interacting conditions, polypharmacy, and complex care needs are particularly exposed to health care-related adverse events. Among these, anticoagulant-related thromboembolic and hemorrhagic events are particularly frequent and serious in older inpatients. The growing use of anticoagulants in this population and their substantial risk of toxicity and inefficacy have therefore become an important patient safety and public health concern worldwide. Anticoagulant-related adverse events and the quality of anticoagulation management should thus be routinely assessed to improve patient safety in vulnerable older inpatients. This project aims to develop and validate a set of outcome and process indicators based on linked administrative health data (ie, insurance claims data linked to hospital discharge data) assessing older inpatient safety related to anticoagulation in both Switzerland and France, and enabling comparisons across time and among hospitals, health territories, and countries. Geriatric patient safety indicators (GPSIs) will assess anticoagulant-related adverse events. Geriatric quality indicators (GQIs) will evaluate the management of anticoagulants for the prevention and treatment of arterial or venous thromboembolism in older inpatients. GPSIs will measure cumulative incidences of thromboembolic and bleeding adverse events based on hospital discharge data linked to insurance claims data. Using linked administrative health data will improve GPSI risk adjustment on patients' conditions that are present at admission and will capture in-hospital and postdischarge adverse events. GQIs will estimate the proportion of index hospital stays resulting in recommended anticoagulation at discharge and up to various time frames based on the same electronic health data. The GPSI and GQI development and validation process will comprise 6 stages: (1) selection and specification of candidate indicators, (2) definition of administrative data

Natural Elemental Concentrations and Fluxes: Their Use as Indicators of Repository Safety

International Nuclear Information System (INIS)

Miller, Bill; Lind, Andy; Savage, Dave; Maul, Philip; Robinson, Peter

2002-03-01

The calculated post-closure performance of a radioactive waste repository is generally quantified in terms of radiological dose or risk to humans, with safety being determined by whether the calculated exposure values are consistent with predetermined target criteria which are deemed to represent acceptable radiological hazards. Despite their general acceptance, however, dose and risk are not perfect measures of repository safety because, in order to calculate them, gross assumptions must be made for future human behaviour patterns. Such predictions clearly become increasingly uncertain as forecasts are made further into the future. As a consequence, there has been a growing interest in developing other ways of assessing repository safety which do not require assumptions to be made for future human behaviour. One proposed assessment method is to use the distributions of naturally-occurring chemical species in the environment, expressed either as concentrations or fluxes of elements, radionuclides or radioactivity, as natural safety indicators which may be compared with the PA predictions of repository releases. Numerous comparisons are possible between the repository and natural systems. The primary objective is to use the natural system to provide context to the hazard presented by the repository releases. Put simply, if it can be demonstrated that the flux to the biosphere from the repository is not significant compared with the natural flux from the geosphere, then its radiological significance should not be of great or priority concern. Natural safety indicators may be quantified on a site specific basis, using information derived from a repository site characterisation programme, and can be compared to the outputs from the associated site specific PAs. Such calculations and comparisons may be very detailed and might examine, for example, the spatial and temporal variations in the distributions and fluxes of naturally-occurring chemical species arising from

Safety Considerations in the Selection of Nuclear Power Plant Candidate Sites in Johor State, Malaysia

International Nuclear Information System (INIS)

Ramli, A.T.; Basri, N.A.; Abu Hanifah, N.Z.H.

2014-01-01

Nuclear power is considered as one of the best options for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation / production, commissioning the first nuclear power plant needs tremendous effort in various aspects. The most obvious challenges are to ensure the nation’s safety and to handle security issues that may arise from a nuclear power plant site. This paper aims to propose a site for nuclear power plant in Johor State, Malaysia as well as listing the possible safety challenges in the process. The site selection uses the Malaysian Atomic Energy Licensing Board (AELB) guideline document as the main reference, supported by documents from International Atomic Energy Agency (IAEA) and from various countries. Only five site characteristics are chosen as study parameters – geological features and seismic data, air dispersion analysis using meteorological data, population distribution, safety zones and emergency supports. This paper concluded that site number 2 (CS2) at Tanjung Tenggaroh, Mersing is the most suitable area for nuclear power plant in Johor state. It has the least possible risks, safety and security issues. (author)

Safety Considerations in the Selection of Nuclear Power Plant Candidate Sites in Johor State, Malaysia

Energy Technology Data Exchange (ETDEWEB)

Ramli, A. T.; Basri, N. A.; Abu Hanifah, N. Z.H., [Department of Physics, Faculty of Science Universiti Teknologi Malaysia Johor (Malaysia)

2014-10-15

Nuclear power is considered as one of the best options for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation / production, commissioning the first nuclear power plant needs tremendous effort in various aspects. The most obvious challenges are to ensure the nation’s safety and to handle security issues that may arise from a nuclear power plant site. This paper aims to propose a site for nuclear power plant in Johor State, Malaysia as well as listing the possible safety challenges in the process. The site selection uses the Malaysian Atomic Energy Licensing Board (AELB) guideline document as the main reference, supported by documents from International Atomic Energy Agency (IAEA) and from various countries. Only five site characteristics are chosen as study parameters – geological features and seismic data, air dispersion analysis using meteorological data, population distribution, safety zones and emergency supports. This paper concluded that site number 2 (CS2) at Tanjung Tenggaroh, Mersing is the most suitable area for nuclear power plant in Johor state. It has the least possible risks, safety and security issues. (author)

A multidisciplinary three-phase approach to improve the clinical utility of patient safety indicators.

Science.gov (United States)

Najjar, Peter; Kachalia, Allen; Sutherland, Tori; Beloff, Jennifer; David-Kasdan, Jo Ann; Bates, David W; Urman, Richard D

2015-01-01

The AHRQ Patient Safety Indicators (PSIs) are used for calculation of risk-adjusted postoperative rates for adverse events. The payers and quality consortiums are increasingly requiring public reporting of hospital performance on these metrics. We discuss processes designed to improve the accuracy and clinical utility of PSI reporting in practice. The study was conducted at a 793-bed tertiary care academic medical center where PSI processes have been aggressively implemented to track patient safety events at discharge. A three-phased approach to improving administrative data quality was implemented. The initiative consisted of clinical review of all PSIs, documentation improvement, and provider outreach including active querying for patient safety events. This multidisciplinary effort to develop a streamlined process for PSI calculation reduced the reporting of miscoded PSIs and increased the clinical utility of PSI monitoring. Over 4 quarters, 4 of 41 (10%) PSI-11 and 9 of 138 (7%) PSI-15 errors were identified on review of clinical documentation and appropriate adjustments were made. A multidisciplinary, phased approach leveraging existing billing infrastructure for robust metric coding, ongoing clinical review, and frontline provider outreach is a novel and effective way to reduce the reporting of false-positive outcomes and improve the clinical utility of PSIs.

Organizational analysis and safety for utilities with nuclear power plants: perspectives for organizational assessment. Volume 2

International Nuclear Information System (INIS)

Osborn, R.N.; Olson, J.; Sommers, P.E.

1983-08-01

This two-volume report presents the results of initial research on the feasibility of applying organizational factors in nuclear power plant (NPP) safety assessment. Volume 1 of this report contains an overview of the literature, a discussion of available safety indicators, and a series of recommendations for more systematically incorporating organizational analysis into investigations of nuclear power plant safety. The six chapters of this volume discuss the major elements in our general approach to safety in the nuclear industry. The chapters include information on organizational design and safety; organizational governance; utility environment and safety related outcomes; assessments by selected federal agencies; review of data sources in the nuclear power industry; and existing safety indicators

Stakeholders' perspectives on quality indicators for diabetes care: a qualitative study.

Science.gov (United States)

Markhorst, Joekie; Martirosyan, Liana; Calsbeek, Hiske; Braspenning, Jozé

2012-01-01

Transparency in diabetes care requires quality indicators that are of interest to stakeholders in order to optimise their usage. Indicator development is often focused on consensus, and little is known about stakeholders' preferences for information on quality. To explore the preferences of consumers, providers, purchasers and policy makers for different quality domains and indicators in relation to the intended use of quality indicators. Between June and December 2009, 14 semi-structured interviews were held with stakeholders who have a decisive vote in the selection of the national indicator set for diabetes care in the Netherlands. The following subjects were explored: (1) the aims of using information on quality; (2) the interpretation of and preferences for the quality domains of safety, timeliness, effectiveness and patient-centredness in relation to the user aims; and (3) the preferences for structure, process or outcome indicators. Content analysis was used to analyse qualitative data. Stakeholders had similar and different aims according to their roles. The interpretations of quality domains varied greatly between the stakeholders. Besides differences in interpretation, their preferences were similar. Most stakeholders prioritised patient-centredness above the other domains of quality, ranked in order of priority as safety, effectiveness and timeliness, whereas purchasers also prioritised efficiency. All stakeholders preferred to use process indicators or a mix of process and outcome indicators. The preferences of the stakeholders for quality indicators seem to be neither well-refined nor congruent. The implementation of an indicator set can probably be improved if the stakeholders' definitions and preferences for quality domains become more explicit during the selection process for indicators.

Implementation of the safety culture for HANARO safety management

Energy Technology Data Exchange (ETDEWEB)

Wu, Jong Sup; Han, Gee Yang; Kim, Ik Soo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-11-15

Safety is the fundamental principal upon which a management system is based. The IAEA INSAG(International Nuclear Safety Group) states the general aims of a safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams, so as to allow them to carry out their tasks safety. The safety culture activities have been implemented and the importance of a safety management in nuclear activities for a reactor application and utilization has also been emphasized for more than 10 years in HANARO which is a 30 MW multi purpose research reactor that achieved its first criticality in February 1995. The safety culture activities and implementation have been conducted continuously to enhance its safe operation such as the seminars and lectures related to safety matters, participation in international workshops and the development of safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of an e Learning program for a safety education purpose.

Implementation of the safety culture for HANARO safety management

International Nuclear Information System (INIS)

Wu, Jong Sup; Han, Gee Yang; Kim, Ik Soo

2008-01-01

Safety is the fundamental principal upon which a management system is based. The IAEA INSAG(International Nuclear Safety Group) states the general aims of a safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams, so as to allow them to carry out their tasks safety. The safety culture activities have been implemented and the importance of a safety management in nuclear activities for a reactor application and utilization has also been emphasized for more than 10 years in HANARO which is a 30 MW multi purpose research reactor that achieved its first criticality in February 1995. The safety culture activities and implementation have been conducted continuously to enhance its safe operation such as the seminars and lectures related to safety matters, participation in international workshops and the development of safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of an e Learning program for a safety education purpose

Perceived Indices of Truancy among Selected Adolescents in Oyo Town: Implications for Behavioural Change

Science.gov (United States)

Adika, Lawrence Olagoke

2016-01-01

The study investigated perceived indices of truancy behaviour among selected adolescents in Oyo town. The descriptive survey study had 200 randomly selected adolescents from five secondary schools in Oyo town. A self-designed instrument tagged Adolescent Truancy Scale (ATS) was employed in collecting data for the study and the data was subjected…

Safety system function trends

International Nuclear Information System (INIS)

Johnson, C.

1989-01-01

This paper describes research to develop risk-based indicators of plant safety performance. One measure of the safety-performance of operating nuclear power plants is the unavailability of important safety systems. Brookhaven National Laboratory and Science Applications International Corporation are evaluating ways to aggregate train-level or component-level data to provide such an indicator. This type of indicator would respond to changes in plant safety margins faster than the currently used indicator of safety system unavailability (i.e., safety system failures reported in licensee event reports). Trends in the proposed indicator would be one indication of trends in plant safety performance and maintenance effectiveness. This paper summarizes the basis for such an indicator, identifies technical issues to be resolved, and illustrates the potential usefullness of such indicators by means of computer simulations and case studies

Multivariate Analysis of Profitability Indicators for Selected Companies of Croatian Market

Directory of Open Access Journals (Sweden)

Ana Perisa

2017-12-01

Full Text Available In this paper, the profitability indicators are analysed for the first hundred companies of the Croatian market, which are classified according to the net profit. The profitability indicators included in the analysis are the following: EBIT margin, EBITDA margin, net profit margin, return on assets (ROA, return on invested capital (ROI and return on capital employed (ROCE. By implementing the factor analysis, six chosen profitability indicators have been reduced to two factors, thus solving the multicollinearity problem, which is one of the prerequisites for the cluster analysis. For two extracted factors, the factor scores are calculated and used in the following cluster analysis. By implementing the cluster analysis, selected companies are grouped into clusters according to their similarity in accomplished results that are measured by profitability indicators. The hierarchical and non-hierarchical cluster analyses are conducted and resulted into two clusters where ten companies were in the first cluster, while the other ninety were in the second cluster

Prediction of genetic gain from selection indices for disease resistance in papaya hybrids

Directory of Open Access Journals (Sweden)

Marcelo Vivas

2012-12-01

Full Text Available In order to select superior hybrids for the concentration of favorable alleles for resistance to papaya black spot, powdery mildew and phoma spot, 67 hybrids were evaluated in two seasons, in 2007, in a randomized block design with two replications. Genetic gains were estimated from the selection indices of Smith & Hazel, Pesek & Baker, Williams, Mulamba & Mock, with selection intensity of 22.39%, corresponding to 15 hybrids. The index of Mulamba & Mock showed gains more suitable for the five traits assessed when it was used the criterion of economic weight tentatively assigned. Together, severity of black spot on leaves and on fruits, characteristics considered most relevant to the selection of resistant materials, expressed percentage gain of -44.15%. In addition, there were gains for other characteristics, with negative predicted selective percentage gain. The results showed that the index of Mulamba & Mock is the most efficient procedure for simultaneous selection of papaya hybrid resistant to black spot, powdery mildew and phoma spot.

Expert Study to Select Indicators of the Occurence of Emerging Mycotoxin Hazards

NARCIS (Netherlands)

Kandhai, M.C.; Booij, C.J.H.; Fels-Klerx, van der H.J.

2011-01-01

This article describes a Delphi-based expert judgment study aimed at the selection of indicators to identify the occurrence of emerging mycotoxin hazards related to Fusarium spp. in wheat supply chains. A panel of 29 experts from 12 European countries followed a holistic approach to evaluate the

Customising turnaround time indicators to requesting clinician: a 10-year study through balanced scorecard indicators.

Science.gov (United States)

Salinas, Maria; López-Garrigós, Maite; Santo-Quiles, Ana; Gutierrez, Mercedes; Lugo, Javier; Lillo, Rosa; Leiva-Salinas, Carlos

2014-09-01

The purpose of this study is, first to present a 10-year monitoring of postanalytical turnaround time (TAT) adapted to different clinicians and patient situations, second to evaluate and analyse the indicators results during that period of time, and finally to show a synthetic appropriate indicator to be included in the balanced scorecard management system. TAT indicator for routine samples was devised as the percentage of certain key tests that were verified before a specific time on the phlebotomy day. A weighted mean synthetic indicator was also designed. They were calculated for inpatients at 15:00 and 12:00 and for primary care patients only at 15:00. The troponin TAT of emergency department patients, calculated as the difference between the troponin verification and registration time, was selected as the stat laboratory TAT indicator. The routine and stat TAT improved along the 10-year study period. The synthetic indicator showed the same trend. The implementation of systematic and continuous monitoring over years, promoted a continuous improvement in TAT which will probably benefit patient outcome and safety.

Improving versus maintaining nuclear safety

International Nuclear Information System (INIS)

2002-01-01

The concept of improving nuclear safety versus maintaining it has been discussed at a number of nuclear regulators meetings in recent years. National reports have indicated that there are philosophical differences between NEA member countries about whether their regulatory approaches require licensees to continuously improve nuclear safety or to continuously maintain it. It has been concluded that, while the actual level of safety achieved in all member countries is probably much the same, this is difficult to prove in a quantitative way. In practice, all regulatory approaches require improvements to be made to correct deficiencies and when otherwise warranted. Based on contributions from members of the NEA Committee on Nuclear Regulatory Activities (CNRA), this publication provides an overview of current nuclear regulatory philosophies and approaches, as well as insights into a selection of public perception issues. This publication's intended audience is primarily nuclear safety regulators, but government authorities, nuclear power plant operators and the general public may also be interested. (author)

School climate factors contributing to student and faculty perceptions of safety in select Arizona schools.

Science.gov (United States)

Bosworth, Kris; Ford, Lysbeth; Hernandaz, Diley

2011-04-01

To ensure that schools are safe places where students can learn, researchers and educators must understand student and faculty safety concerns. This study examines student and teacher perceptions of school safety. Twenty-two focus groups with students and faculty were conducted in 11 secondary schools. Schools were selected from a stratified sample to vary in location, proximity to Indian reservations, size, and type. The data analysis was based on grounded theory. In 9 of 11 schools, neither faculty nor students voiced overwhelming concerns about safety. When asked what makes school safe, students tended to report physical security features. School climate and staff actions also increased feelings of safety. Faculty reported that relationships and climate are key factors in making schools safe. High student performance on standardized tests does not buffer students from unsafe behavior, nor does living in a dangerous neighborhood necessarily lead to more drug use or violence within school walls. School climate seemed to explain the difference between schools in which students and faculty reported higher versus lower levels of violence and alcohol and other drug use. The findings raise provocative questions about school safety and provide insight into elements that lead to perceptions of safety. Some schools have transcended issues of location and neighborhood to provide an environment perceived as safe. Further study of those schools could provide insights for policy makers, program planners, and educational leaders. © 2011, American School Health Association.

Evaluation Indicators for Analysis of Nuclear Fuel Cycle Sustainability

Energy Technology Data Exchange (ETDEWEB)

Jeong, Chang Joon; Ko, Won Il; Chang, Hong Lae

2008-01-15

In this report, an attempt was made to derive indicators for the evaluation of the sustainability of the nuclear fuel cycle, using the methodologies developed by the INPRO, OECD/NEA and Gen-IV. In deriving the indicators, the three main elements of the sustainability, i.e., economics, environmental impact, and social aspect, as well as the technological aspect of the nuclear fuel cycle, considering the importance of the safety, were selected as the main criteria. An evaluation indicator for each criterion was determined, and the contents and evaluation method of each indicator were proposed. In addition, a questionnaire survey was carried out for the objectivity of the selection of the indicators in which participated some experts of the Korea Energy Technology and Emergency Management Institute (KETEMI) . Although the proposed indicators do not satisfy the characteristics and requirements of general indicators, it is presumed that they can be used in the analysis of the sustainability of the nuclear fuel cycle because those indicators incorporate various expert judgment and public opinions. On the other hand, the weighting factor of each indicator should be complemented in the future, using the AHP method and expert advice/consultations.

Convergence processes of selected demographic indicators in regions of the Czech Republic

Directory of Open Access Journals (Sweden)

Bohumil Minařík

2010-01-01

Full Text Available A number of authors deal with problems of convergence, divergence and disparities, particularly with reference to economic growth and its comparison in groups of countries. This paper is aimed at problems of using basic methods of measuring the convergence at the evaluation of the development of selected demographic characteristics of particular regions of the Czech Republic for the period 1992 to 2007. From demographic data provided by the Czech Statistical Office some indicators were selected associated with aging the CR population. In particular, following indicators were used: the proportion of productive population, coefficient of loading the productive population by young persons, coefficient of loading the productive population by old persons, coefficient of the total loading and index of age. A precondition served as a working hypothesis that in addition to the negative demographic development affecting the CR as a whole, the convergence of its particular regions also occurred, viz. regions at the level of NUTS 3. At the quantification of convergence processes in particular regions of the CR, the method of beta convergence was used (in a simplified linearized form as well as the method of sigma convergence. Both methods predicate unambiguously on the convergence of the CR regions from the point of view of all examined demographic indicators. From the aspect of both methods, the fastest convergence occurred in the studied period in the indicator of loading the productive population by old persons. In this indicator (as the only from monitored ones, no disparity showed as well, ie a region showing an isolated development was not noted. Opposite situation manifested itself at the indicator of loading the productive population by young persons. Only elimination of the capital city of Prague reversed an original result showing evidence of the divergence of regions from the aspect of this indicator. Disparities of the capital city of Prague

Preliminary safety evaluation for CSR1000 with passive safety system

International Nuclear Information System (INIS)

Wu, Pan; Gou, Junli; Shan, Jianqiang; Zhang, Bo; Li, Xiang

2014-01-01

Highlights: • The basic information of a Chinese SCWR concept CSR1000 is introduced. • An innovative passive safety system is proposed for CSR1000. • 6 Transients and 3 accidents are analysed with system code SCTRAN. • The passive safety systems greatly mitigate the consequences of these incidents. • The inherent safety of CSR1000 is enhanced. - Abstract: This paper describes the preliminary safety analysis of the Chinese Supercritical water cooled Reactor (CSR1000), which is proposed by Nuclear Power Institute of China (NPIC). The two-pass core design applied to CSR1000 decreases the fuel cladding temperature and flattens the power distribution of the core at normal operation condition. Each fuel assembly is made up of four sub-assemblies with downward-flow water rods, which is favorable to the core cooling during abnormal conditions due to the large water inventory of the water rods. Additionally, a passive safety system is proposed for CSR1000 to increase the safety reliability at abnormal conditions. In this paper, accidents of “pump seizure”, “loss of coolant flow accidents (LOFA)”, “core depressurization”, as well as some typical transients are analysed with code SCTRAN, which is a one-dimensional safety analysis code for SCWRs. The results indicate that the maximum cladding surface temperatures (MCST), which is the most important safety criterion, of the both passes in the mentioned incidents are all below the safety criterion by a large margin. The sensitivity analyses of the delay time of RCPs trip in “loss of offsite power” and the delay time of RMT actuation in “loss of coolant flowrate” were also included in this paper. The analyses have shown that the core design of CSR1000 is feasible and the proposed passive safety system is capable of mitigating the consequences of the selected abnormalities

TOO MANY APPS: BENCHMARKS AND INDICATORS TO SELECT TOPAPP CHILDREN READING APP

Directory of Open Access Journals (Sweden)

Araceli García-Rodríguez

2015-10-01

Full Text Available Based on the need to systematize criteria for evaluating applications reading for children, in an objective manner the article proposes a list of indicators structured parameters which in turn are grouped into the dimensions of form and content. The form dimension includes the availability, acquisition, security, privacy, popularity, recognition, usability and ergonomics. Contended the covers of indicators related to authorship, update, accessibility, organization, customization and interaction with content and audio quality and interactivity. As a result, practical application the article proposes a template that includes the fundamental aspects and evaluate the indication of those that are recommended or required in order to facilitate the selection of children's reading applications.

Interface between radiation protection and nuclear safety

International Nuclear Information System (INIS)

Bengtsson, G.; Hoegberg, L.

1991-01-01

Interface issues concern the character and management of overlaps between radiation protection and nuclear safety in nuclear power plants. Typical examples include the selection of inspection and maintenance volumes in order to balance occupational radiation doses versus the safety status of the plant, and the intentional release to the environment in the course of an accident in order to secure better plant control. The paper discusses whether it is desirable and possible to employ a consistent management of interface issues with trade-offs between nuclear safety and radiation protection. Illustrative examples are quoted from a major Nordic research programme on risk analysis and safety rationale. These concern for instance in-service inspections, modifications of plant systems and constructions after the plant has been taken into operation, and studies on the limitations of probabilistic safety assessment. They indicate that in general there are no simple rules for such trade-offs

Measuring coverage in MNCH: challenges and opportunities in the selection of coverage indicators for global monitoring.

Directory of Open Access Journals (Sweden)

Jennifer Harris Requejo

Full Text Available Global monitoring of intervention coverage is a cornerstone of international efforts to improve reproductive, maternal, newborn, and child health. In this review, we examine the process and implications of selecting a core set of coverage indicators for global monitoring, using as examples the processes used by the Countdown to 2015 for Maternal, Newborn and Child Survival and the Commission on Accountability for Women's and Children's Health. We describe how the generation of data for global monitoring involves five iterative steps: development of standard indicator definitions and measurement approaches to ensure comparability across countries; collection of high-quality data at the country level; compilation of country data at the global level; organization of global databases; and rounds of data quality checking. Regular and rigorous technical review processes that involve high-level decision makers and experts familiar with indicator measurement are needed to maximize uptake and to ensure that indicators used for global monitoring are selected on the basis of available evidence of intervention effectiveness, feasibility of measurement, and data availability as well as programmatic relevance. Experience from recent initiatives illustrates the challenges of striking this balance as well as strategies for reducing the tensions inherent in the indicator selection process. We conclude that more attention and continued investment need to be directed to global monitoring, to support both the process of global database development and the selection of sets of coverage indicators to promote accountability. The stakes are high, because these indicators can drive policy and program development at the country and global level, and ultimately impact the health of women and children and the communities where they live.

Selected Health Status Indicators and Behaviors of Young Adults, United States-2003

Science.gov (United States)

Eaton, Danice K.; Kann, Laura; Okoro, Catherine A.; Collins, Janet

2007-01-01

This study examined the prevalence of selected clinical preventive health services, health status indicators, health risk behaviors, and health-promoting behaviors among adults aged 18 to 24 years in the general U.S. population. The study analyzed data from the 2003 Behavioral Risk Factor Surveillance System. Nearly 30% of young adults lacked…

An environmental scan of quality indicators in critical care.

Science.gov (United States)

Valiani, Sabira; Rigal, Romain; Stelfox, Henry T; Muscedere, John; Martin, Claudio M; Dodek, Peter; Lamontagne, François; Fowler, Robert; Gheshmy, Afshan; Cook, Deborah J; Forster, Alan J; Hébert, Paul C

2017-06-21

We performed a directed environmental scan to identify and categorize quality indicators unique to critical care that are reported by key stakeholder organizations. We convened a panel of experts ( n = 9) to identify key organizations that are focused on quality improvement or critical care, and reviewed their online publications and website content for quality indicators. We identified quality indicators specific to the care of critically ill adult patients and then categorized them according to the Donabedian and the Institute of Medicine frameworks. We also noted the organizations' rationale for selecting these indicators and their reported evidence base. From 28 targeted organizations, we identified 222 quality indicators, 127 of which were unique. Of the 127 indicators, 63 (32.5%) were safety indicators and 61 (31.4%) were effectiveness indicators. The rationale for selecting quality indicators was supported by consensus for 58 (26.1%) of the 222 indicators and by published research evidence for 45 (20.3%); for 119 indicators (53.6%), the rationale was not reported or the reader was referred to other organizations' reports. Of the 127 unique quality indicators, 27 (21.2%) were accompanied by a formal grading of evidence, whereas for 52 (40.9%), no reference to evidence was provided. There are many quality indicators related to critical care that are available in the public domain. However, owing to a paucity of rationale for selection, supporting evidence and results of implementation, it is not clear which indicators should be adopted for use. Copyright 2017, Joule Inc. or its licensors.

Risk-based plant performance indicators

International Nuclear Information System (INIS)

Boccio, J.L.; Azarm, M.A.; Hall, R.E.

1991-01-01

Tasked by the 1979 President's Commission on the Accident at Three Mile Island, the U.S. nuclear power industry has put into place a performance indicator program as one means for showing a demonstrable record of achievement. Largely through the efforts of the Institute of Nuclear Power Operations (INPO), plant performance data has, since 1983, been collected and analyzed to aid utility management in measuring their plants' performance progress. The U.S. Nuclear Regulatory Commission (NRC) has also developed a set of performance indicators. This program, conducted by NRC's Office for the Analysis and Evaluation of Operational Data (AEOD), is structured to present information on plant operational performance in a manner that could enhance the staff's ability to recognize changes in the safety performance. Both organizations recognized that performance indicators have limitations and could be subject to misinterpretation and misuse with the potential for an adverse impact on safety. This paper reports on performance indicators presently in use, e.g., unplanned automatic scrams, unplanned safety system actuation, safety system failures, etc., which are logically related to safety. But, a reliability/risk-based method for evaluating either individual indicators or an aggregated set of indicators is not yet available

Organizational analysis and safety for utilities with nuclear power plants: perspectives for organizational assessment. Volume 2. [PWR; BWR

Energy Technology Data Exchange (ETDEWEB)

Osborn, R.N.; Olson, J.; Sommers, P.E.; McLaughlin, S.D.; Jackson, M.S.; Nadel, M.V.; Scott, W.G.; Connor, P.E.; Kerwin, N.; Kennedy, J.K. Jr.

1983-08-01

This two-volume report presents the results of initial research on the feasibility of applying organizational factors in nuclear power plant (NPP) safety assessment. Volume 1 of this report contains an overview of the literature, a discussion of available safety indicators, and a series of recommendations for more systematically incorporating organizational analysis into investigations of nuclear power plant safety. The six chapters of this volume discuss the major elements in our general approach to safety in the nuclear industry. The chapters include information on organizational design and safety; organizational governance; utility environment and safety related outcomes; assessments by selected federal agencies; review of data sources in the nuclear power industry; and existing safety indicators.

National report of the Slovak Republic compiled according to the terms of the convention on nuclear safety

International Nuclear Information System (INIS)

Adamovsky, V.; Betak, A.; Balaj, J.; Bystricka, S.; Grebeciova, J.; Husarcek, J.; Metke, E.; Pospisil, M.; Smrtnik, I.; Turner, M.; Uhrik, P.; Zemanova, D.; Bulla, R.; Filip, A.; Jurina, V.; Sedlak, M.; Tomek, J.; Zimermann, M.

2013-06-01

A brief safety report of the Slovak Republic in 2013 is presented. A account of activities carried out by the Nuclear Regulatory Authority of the Slovak Republic (UJD) is presented. These activities are reported under the headings: (1) Introduction; (2) Nuclear installations in Slovak Republic in terms of the convention; (3) Legislation and regulation; (4) General safety aspects; (5) Safety of nuclear installations in the Slovak Republic; ((6) Annexes; (6.1) List of nuclear installations and technical and economic indicators; (6.2) Selected generally binding legal regulations and safety guidelines in relation to nuclear and radiation safety; (6.3) List of selected national and international documents applicable to safety of nuclear installations; (6.4) Limits for radioactive discharges; (6.5) IAEA Action Plan on Nuclear Safety; (6.6) Team of authors.

Seismic safety of nuclear power plants

International Nuclear Information System (INIS)

Guerpinar, A.; Godoy, A.

2001-01-01

This paper summarizes the work performed by the International Atomic Energy Agency in the areas of safety reviews and applied research in support of programmes for the assessment and enhancement of seismic safety in Eastern Europe and in particular WWER type nuclear power plants during the past seven years. Three major topics are discussed; engineering safety review services in relation to external events, technical guidelines for the assessment and upgrading of WWER type nuclear power plants, and the Coordinated Research Programme on 'Benchmark study for the seismic analysis and testing of WWER type nuclear power plants'. These topics are summarized in a way to provide an overview of the past and present safety situation in selected WWER type plants which are all located in Eastern European countries. Main conclusion of the paper is that although there is now a thorough understanding of the seismic safety issues in these operating nuclear power plants, the implementation of seismic upgrades to structures, systems and components are lagging behind, particularly for those cases in which the re-evaluation indicated the necessity to strengthen the safety related structures or install new safety systems. (author)

Do clinical safety charts improve paramedic key performance indicator results? (A clinical improvement programme evaluation).

Science.gov (United States)

Ebbs, Phillip; Middleton, Paul M; Bonner, Ann; Loudfoot, Allan; Elliott, Peter

2012-07-01

Is the Clinical Safety Chart clinical improvement programme (CIP) effective at improving paramedic key performance indicator (KPI) results within the Ambulance Service of New South Wales? The CIP intervention area was compared with the non-intervention area in order to determine whether there was a statistically significant improvement in KPI results. The CIP was associated with a statistically significant improvement in paramedic KPI results within the intervention area. The strategies used within this CIP are recommended for further consideration.

Examples of safety culture practices

International Nuclear Information System (INIS)

1997-01-01

This report has been prepared to illustrate the concepts and principles of safety culture produced in 1991 by the International Safety Advisory Group as 75-INSAG-4. It provides a small selection of examples taken from a worldwide collection of safety performance evaluations (e.g. IAEA safety series, national regulatory inspections, utility audits and a plant assessments). These documented evaluations collectively provide a database of safety performance strengths and weakness, and related safety culture observations. The examples which have been selected for inclusion in this report are those which are considered worthy of special mention and which illustrate a specific attribute of safety culture given in 75-INSAG-4

Evaluation of different selection indices combining Pilodyn penetration and growth performance in Eucalyptus clones

Directory of Open Access Journals (Sweden)

Andrei Caíque Pires Nunes

2017-06-01

Full Text Available The present study aimed to evaluate the selection indices efficiency for Pilodyn penetration combined with growth traits in Eucalyptus clones. It was carried out experiments in a randomized block design, with single tree plots and 30 replications. Diameter at breast height (DBH, total height (TH, and Pilodyn penetration as an indicator of basic density (BD were measured. The volume was estimated. Based on predicted genotypic values, three indices presented the highest accuracies: I8 (based on partial correlation, I7 (based on the concept of multivariate BLUP and I3 (based on two variables as ratio, which uses a third heritability estimate associated to the ratio DBH/BD, besides the two heritabilities of DBH and BD. Thus, it is possible to optimize the selection by combining properly the variables using their genetic control, precision and the relationships between them. The best options came from using only two no redundant traits DBH and BD.

[Associations of occupational safety atmosphere and behaviors with unintentional injuries].

Science.gov (United States)

Xiao, Ya-ni; Huang, Zhi-xiong; Huang, Shao-bin; Cao, Xiao-ou; Chen, Xia-ming; Liu, Xu-hua; Chen, Wei-qing

2012-07-01

To evaluate the associations of perception of safety atmosphere at workplace, occupational safety attitude and behaviors with occupational unintentional injury among manufacturing workers. A cross-sectional study was performed and a self-administered questionnaire was used to inquire socio-demographic characteristics, perceived safety atmosphere, occupational safety attitudes, occupational safety behaviors and occupational unintentional injuries among 10585 manufacturing workers selected from 46 enterprises in Guangdong. Structural equation modeling was applied to assess the relationship of the perception of safety atmosphere at workplace, occupational safety attitude, and occupational safety behaviors with occupational unintentional injury. Among 24 pathways supposed in structural equation model, 20 pathways (except for the attitude toward occupational safety, the attitude toward managers' support, the work posture and individual protection) were significantly related to the occupational unintentional injuries. The further analysis indicated that the perceived safety atmosphere might impact the occupational unintentional injuries by the attitude toward occupational safety and occupational safety behaviors. Workers' perception of safety atmosphere indirectly influenced on occupational unintentional injuries through occupational safety attitudes and occupational safety behaviors.

Nursing home safety: does financial performance matter?

Science.gov (United States)

Oetjen, Reid M; Zhao, Mei; Liu, Darren; Carretta, Henry J

2011-01-01

This study examines the relationship between financial performance and selected safety measures of nursing homes in the State of Florida. We used descriptive analysis on a total sample of 1,197. Safety information was from the Online Survey, Certification and Reporting (OSCAR) data of 2003 to 2005, while the financial performance measures were from the Medicare cost reports of 2002 to 2004. Finally, we examined the most frequently cited deficiencies as well as the relationship between financial performance and quality indicators. Nursing homes in the bottom quartile of financial performance perform poorly on most resident-safety measures of care; however, nursing homes in the top two financial categories also experienced a higher number of deficiencies. Nursing homes in the next to lowest quartile of financial performance category best perform on most of these safety measures. The results reinforce the need to monitor nursing home quality and resident safety in US nursing homes, especially among facilities with poor overall financial performance.

Potential safety features and safety analysis aspects for high performance light water reactor (HPLWR)

International Nuclear Information System (INIS)

Aksan, N.; Schulenberg, T.; Squarer, D.

2003-01-01

Research Activities are ongoing worldwide to develop advanced nuclear power plants with high thermal efficiency for the purpose to improve their economical competitiveness. Within the 5th Framework Programme of the European Commission, a project has been launched with the main objective to assess the technical and economical feasibility of a high efficiency LWR operating at super critical pressure conditions. Several European research institutions, industrial partners and the University of Tokyo participated and worked in this common research project. Within the aims of the development of the HPLWR is to use both passive and active safety systems for performing safety related functions in the event of transients or accidents. Consequently substantial effort has been invested in order to define the safety features of the plant in a European environment, as well as to incorporate passive safety features into the design. Throughout this process, the European Utility Requirements (EUR) and requirements known from Generation IV initiative were considered as a guideline in general terms in order to include further advanced ideas. The HPLWR general features were compared to both requirements, indicating a potential to meet these. Since, the supercritical HPLWR represents a challenge for best-estimate safety codes like RELAP5, CATHARE and TRAB due to the fact that these codes were developed for two-phase or single-phase coolant at pressures far below critical point, work on the preliminary assessment of the appropriateness of these codes have been performed for selected relevant phenomena, and application of the codes to the selected transients on the basis of defined 'reference design'. An overview on their successful upgrade to supercritical pressures and application to some plant safety analysis are provided in the paper. Further elaborations in relation to future needs are also discussed. (author)

Human factors in safety assessment. Safety culture assessment

International Nuclear Information System (INIS)

Zhang Li; Deng Zhiliang; Wang Yiqun; Huang Weigang

1996-01-01

This paper analyses the present conditions and problems in enterprises safety assessment, and introduces the characteristics and effects of safety culture. The authors think that safety culture must be used as a 'soul' to form the pattern of modern safety management. Furthermore, they propose that the human safety and synthetic safety management assessment in a system should be changed into safety culture assessment. Finally, the assessment indicators are discussed

Safety properties test data selection from an algebraic model of Lustre programs; Selection de tests de proprietes de surete a partir d'une modelisation algebrique de programmes lustre

Energy Technology Data Exchange (ETDEWEB)

Hsiao, N.Ch

1995-07-01

In the context to validate an industrial software, which is a set of reactive programs, we are confronted with the safety properties verification problem. This thesis reports an experience in which our goal is to generate the test data satisfying a safety property. The software to be validated is designed with the SAGA tool, in which a view can be regarded as a program of a programming language called LUSTRE. We adapt a test data generation tool called LOFT to this kind of programs. In this way, we consider the functional testing method on which the LOFT tool is based. Given any LUSTRE program, we try to give it an algebraic model because LOFT treats algebraic specifications. So, our task consists In defining a formal framework in which any LUSTRE program can be translated into a LOFT module: based on an operational semantics of the LUSTRE language, the flow types 'T-flow' are specified with the constructive algebraic formalism, then implemented in a LOFT modules base. Next, in a test selection process assisted by LOFT, a safety property Is expressed by an equation to join other control hypotheses, and to guide the test data selection. Some concrete test data set are generated in this way on some significant examples. This experience confirm the feasibility of formal method on test data selection for the reactive programs. (author)

An ecologically-based method for selecting ecological indicators for assessing risks to biological diversity from genetically-engineered plants

DEFF Research Database (Denmark)

Andow, D. A.; Lövei, Gabor L; Arpaia, Salvatore

2013-01-01

into ecological functional groups and selecting those that deliver the identified environmental values. (3) All of the species or ecosystem processes related to the selected functional groups are identified and (4) multi-criteria decision analysis (MCDA) is used to rank the indicator endpoint entities, which may...... adverse effects to biological diversity. The approach starts by (1) identifying the local environmental values so the ERA addresses specific concerns associated with local biological diversity. The model simplifies the indicator endpoint selection problem by (2) classifying biological diversity...... be species or ecological processes. MCDA focuses on those species and processes that are critical for the identified ecological functions and are likely to be highly exposed to the GE organism. The highest ranked indicator entities are selected for the next step. (5) Relevant risk hypotheses are identified...

Boundary conditions for pathways, safety analysis and basic criteria for low-level radiation waste site selection

International Nuclear Information System (INIS)

Saverot, P.

1994-01-01

There are three successive periods in the life of a disposal facility: the operating period, the institutional control period and the unrestricted site access period. The purpose of safety analysis of the disposal facility is to ensure that the radiological impacts for each period in the life of the facility are acceptable under all circumstances. Founded on a deterministic approach, this analysis leads to a determination of the maximum quantity of each radionuclide present in the facility at the beginning of the institutional control period in order for the impacts to be considered acceptable. Safety analysis involves the calculation of the radiological impacts of a given radiological inventory under a selected scenario, from all plausible scenarios of radionuclide migration to the environment in both normal and accident conditions, and taking into account other specified variables. The calculation itself involves an assessment of the quantities of radionuclides that could be released to the environment under the specific scenario selected and following identified pathways, and a determination of the resultant exposure, both internal and external, to the public. An iterative approach is used in the performance of pathways analyses. If the pathways analyses result in unacceptable radiological impacts, either the radiological inventory of the site is reduced or barrier characteristics not previously factored into the analysis are taken into account. New pathways analyses are then performed until the results are within the acceptable range. Once accepted by the safety authorities, the radiological inventory becomes the radiological capacity, which is the approved quantities of specific radionuclides that may be disposed of at the site. The following elaborates on the boundary conditions used in safety analyses and describes the types of pathways analyses performed for a LLW disposal facility

Safety assessment in plant layout design using indexing approach: Implementing inherent safety perspective

International Nuclear Information System (INIS)

Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

2008-01-01

The design of layout plans requires adequate assessment tools for the quantification of safety performance. The general focus of the present work is to introduce an inherent safety perspective at different points of the layout design process. In particular, index approaches for safety assessment and decision-making in the early stages of layout design are developed and discussed in this two-part contribution. Part 1 (accompanying paper) of the current work presents an integrated index approach for safety assessment of early plant layout. In the present paper (Part 2), an index for evaluation of the hazard related to the potential of domino effects is developed. The index considers the actual consequences of possible escalation scenarios and scores or ranks the subsequent accident propagation potential. The effects of inherent and passive protection measures are also assessed. The result is a rapid quantification of domino hazard potential that can provide substantial support for choices in the early stages of layout design. Additionally, a case study concerning selection among various layout options is presented and analyzed. The case study demonstrates the use and applicability of the indices developed in both parts of the current work and highlights the value of introducing inherent safety features early in layout design

Assessment of the long-term safety of repositories. Scientific basis

International Nuclear Information System (INIS)

Noseck, Ulrich; Becker, Dirk; Fahrenholz, Christine

2008-12-01

The project contributed to increase the scientific knowledge on the long-term safety assessment and the safety cases of a radioactive waste repository. International guidelines and more recent safety cases from other countries were evaluated. The feasibility study of the three safety indicators ''individual dose rate'', ''radiotoxicity concentration in the biosphere water'' and ''radiotoxicity flux from the geosphere'' showed that due to the independently derived corresponding reference values these indicators describe three different safety statements. The combination of the three values can give a stronger argument for the safety of the repository system. Another important methodological aspect of the safety cases is the definition and selection of scenarios, one of these the human intrusion scenario. Various human intrusion scenarios are considered in the different nations, which differ significantly with respect to type and time scale, the exposition type and exposition pathway. Further progress has been achieved in how to treat human intrusion scenarios in a German post-closure safety case. Another port of the project dealt with the impact of specific geochemical processes on the long-term safety of the repository. The impact of climate changes on the long-term safety of a radioactive waste repository in rock salt was investigated with respect to processes in the overburden and the biosphere where highest impact is expected. Sofa simplified models and only discrete climate estates have been considered

A Microbial Assessment Scheme to measure microbial performance of Food Safety Management Systems.

Science.gov (United States)

Jacxsens, L; Kussaga, J; Luning, P A; Van der Spiegel, M; Devlieghere, F; Uyttendaele, M

2009-08-31

A Food Safety Management System (FSMS) implemented in a food processing industry is based on Good Hygienic Practices (GHP), Hazard Analysis Critical Control Point (HACCP) principles and should address both food safety control and assurance activities in order to guarantee food safety. One of the most emerging challenges is to assess the performance of a present FSMS. The objective of this work is to explain the development of a Microbial Assessment Scheme (MAS) as a tool for a systematic analysis of microbial counts in order to assess the current microbial performance of an implemented FSMS. It is assumed that low numbers of microorganisms and small variations in microbial counts indicate an effective FSMS. The MAS is a procedure that defines the identification of critical sampling locations, the selection of microbiological parameters, the assessment of sampling frequency, the selection of sampling method and method of analysis, and finally data processing and interpretation. Based on the MAS assessment, microbial safety level profiles can be derived, indicating which microorganisms and to what extent they contribute to food safety for a specific food processing company. The MAS concept is illustrated with a case study in the pork processing industry, where ready-to-eat meat products are produced (cured, cooked ham and cured, dried bacon).

Implementation of the safety culture for HANARO Safety Management

International Nuclear Information System (INIS)

Wu, Jongsup; Han, Geeyang; Kim, Iksoo

2008-01-01

Safety is the fundamental principal upon which the management system is based. The IAEA INSAG(International Nuclear Safety Group) states the general aims of the safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams so as to allow them to carry out their tasks safety. The safety culture activities have been implemented and the importance of safety management in nuclear activities for a reactor application and utilization has also been emphasized more than 10 years in HANARO which is a 30 MW multi-purpose research reactor and achieved its first criticality in February 1995. The safety culture activities and implementations have been conducted continuously to enhance its safe operation like the seminars and lectures related to safety matters, participation in international workshops, the development of safety culture indicators, the survey on the attitude of safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of an e-Learning program for safety education. (author)

Study of the Continuous Improvement Trend for Health, Safety and Environmental Indicators, after Establishment of Integrated Management System (IMS) in a Pharmaceutical Industry in Iran.

Science.gov (United States)

Mariouryad, Pegah; Golbabaei, Farideh; Nasiri, Parvin; Mohammadfam, Iraj; Marioryad, Hossein

2015-10-01

Nowadays, organizations try to improve their services and consequently adopt management systems and standards which have become key parts in various industries. One of these management systems which have been noticed in the recent years is Integrated Management System that is the combination of quality, health, safety and environment management systems. This study was conducted with the aim of evaluating the improvement trend after establishment of integrated management system for health, safety and environment indicators, in a pharmaceutical industry in Iran. First, during several inspections in different parts of the industry, indicators that should have been noted were listed and then these indicators were organized in 3 domains of health, safety and environment in the form of a questionnaire that followed Likert method of scaling. Also, the weight of each index was resulted from averaging out of 30 managers and the viewpoints of the related experts in the field. Moreover, by checking the documents and evidence of different years (5 contemplation years of this study), the score of each indicator was determined by multiplying the weight and score of the indices and were finally analysed. Over 5 years, scores of health scope indicators, increased from 161.99 to 202.23. Score in the first year after applying the integrated management system establishment was 172.37 in safety part and in the final year increased to 197.57. The changes of environmental scope rates, from the beginning of the program up to the last year increased from 49.24 to 64.27. Integrated management systems help organizations to improve programs to achieve their objectives. Although in this study all trends of health, safety and environmental indicator changes were positive, but at the same time showed to be slow. So, one can suggest that the result of an annual evaluation should be applied in planning future activities for the years ahead.

Safety Cultures in Water-Based Outdoor Activities in Denmark

DEFF Research Database (Denmark)

Andkjær, Søren; Arvidsen, Jan

2015-01-01

In this paper, we report on the study Safe in Nature (Tryg i naturen) in which the aim was to analyze and discuss risk and safety related to outdoor recreation in the coastal regions of Denmark. A cultural perspective is applied to risk management and the safety cultures related to three selected...... water-based outdoor activities: small boat fishing, sea kayaking, and kite surfing. The theoretical framework used was cultural analysis and the methodological approach was mixed methods using case studies with survey and qualitative interviews. The study indicates that safety is a complex matter...... and that safety culture can be understood as the sum and interaction among six categories. The safety culture is closely related to the activity and differs widely among activities. We suggest a broad perspective be taken on risk management wherein risk and safety can be managed at different levels. Small boat...

Selecting Optimal Control Portfolios to Improve Army Aviation Safety

National Research Council Canada - National Science Library

Shelton, Sarah

2001-01-01

.... The Safety Center chartered the Aviation Safety Investment Strategy Team to evaluate accidents to determine their hazards, or contributing conditions, and their controls, or reduction measures...

Risk-based performance indicators

International Nuclear Information System (INIS)

Azarm, M.A.; Boccio, J.L.; Vesely, W.E.; Lofgren, E.

1987-01-01

The purpose of risk-based indicators is to monitor plant safety. Safety is measured by monitoring the potential for core melt (core-melt frequency) and the public risk. Targets for these measures can be set consistent with NRC safety goals. In this process, the performance of safety systems, support systems, major components, and initiating events can be monitored using measures such as unavailability, failure or occurrence frequency. The changes in performance measures and their trends are determined from the time behavior of monitored measures by differentiation between stochastical and actual variations. Therefore, degradation, as well as improvement in the plant safety performance, can be determined. The development of risk-based performance indicators will also provide the means to trace a change in the safety measures to specific problem areas which are amenable to root cause analysis and inspection audits. In addition, systematic methods will be developed to identify specific improvement policies using the plant information system for the identified problem areas. The final product of the performance indicator project will be a methodology, and an integrated and validated set of software packages which, if properly interfaced with the logic model software of a plant, can monitor the plant performance as plant information is provided as input

An exposure-based, ecology-driven framework for selection of indicator species for insecticide risk assessment

Science.gov (United States)

In the current “tiered” paradigm for evaluating risks of insecticidal products, one of the first decisions that must be made is the selection of indicator species to be used in toxicity assays. However, as yet, no formal system has been developed to determine whether proposed indicator species are r...

Chapter No.4. Safety analyses

International Nuclear Information System (INIS)

2002-01-01

for NPP V-1 Bohunice and on review of the impact of the modelling of selected components to the results of calculation safety analysis (a sensitivity study for NPP Mochovce). In 2001 UJD joined a new European project Alternative Approaches to the Safety Performance Indicators. The project is aimed at the information collecting and determining of approaches and recommendations for implementation of the risk oriented indicators, identification of the impact of the safety culture level and organisational culture on safety and applying of indicators to the needs of regulators and operators. In frame of the PHARE project UJD participated in the task focused on severe accident mitigation for nuclear power plants with VVER-440/V213 units. The main results of the analyses of nuclear power plants responses to severe accidents were summarised and the state of their analytical base performed in the past was evaluated within the project. Possible severe accident mitigation and preventative measures were proposed and their applicability for the nuclear power plants with VVER-440/V213 was investigated. The obtained results will be used in assessment activities and accident management of UJD. UJD has been involved also in EVITA project which makes a part of the 5 th EC Framework Programme. The project aims at validation of the European computer code ASTEC dedicated for severe accidents modelling. In 2001 the ASTEC computer code was tested on different platforms. The results of the testing are summarised in the technical report of EC issued in September 2001. Further activities within this project were focused on performing of selected accident scenarios analyses and comparison of the obtained results with the analyses realised with the help of other computer codes. The work on the project will continue in 2002. In 2001 a groundwork on establishing the Centre for Nuclear Safety in Central and Eastern Europe (CENS), the seat of which is going to be in Bratislava, has continued. The

Implementation of the safety culture for HANARO safety management

Energy Technology Data Exchange (ETDEWEB)

Wu, Jongsup; Han, Geeyang; Kim, Iksoo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-11-15

Safety is the fundamental principal upon which a management system is based. The IAEA INSAG (International Nuclear Safety Group) states the general aims of a safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams, so as to allow them to carry out their tasks safely. The safety culture activities have been implemented and the importance of a safety management in nuclear activities for a reactor application and utilization has also been emphasized for more than 10 years in HANARO which is a 30MW multi-purpose research reactor that achieved its first criticality in February 1995. The safety culture activities and implementations have been conducted continuously to enhance its safe operation such as the seminars and lectures related to safety matters, participation in international workshops and the development of safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of a e-learning program for a safety education purpose.

Implementation of the safety culture for HANARO safety management

International Nuclear Information System (INIS)

Wu, Jongsup; Han, Geeyang; Kim, Iksoo

2008-01-01

Safety is the fundamental principal upon which a management system is based. The IAEA INSAG (International Nuclear Safety Group) states the general aims of a safety management system. One of which is to foster and support a strong safety culture through the development and reinforcement of good safety attitudes and behavior in individuals and teams, so as to allow them to carry out their tasks safely. The safety culture activities have been implemented and the importance of a safety management in nuclear activities for a reactor application and utilization has also been emphasized for more than 10 years in HANARO which is a 30MW multi-purpose research reactor that achieved its first criticality in February 1995. The safety culture activities and implementations have been conducted continuously to enhance its safe operation such as the seminars and lectures related to safety matters, participation in international workshops and the development of safety culture indicators, a survey on the attitude of HANARO staff toward the safety culture, the development of operational safety performance indicators (SPIs), the preparation of a safety text book and the development of a e-learning program for a safety education purpose

Perceived Indications, Safety and Efficacy of Perinatal Use of ...

African Journals Online (AJOL)

Cheboi SK

Subjects and Methods: A descriptive cross- sectional ... easy labour and safe delivery (39.6%); and treatment of common ailments (28.5%). Majority ... structures for censoring, training, regulation of TM practice and safety of remedies used.

Formal Safety versus Real Safety: Quantitative and Qualitative Approaches to Safety Culture – Evidence from Estonia

Directory of Open Access Journals (Sweden)

Järvis Marina

2016-10-01

Full Text Available This paper examines differences between formal safety and real safety in Estonian small and medium-sized enterprises. The results reveal key issues in safety culture assessment. Statistical analysis of safety culture questionnaires showed many organisations with an outstanding safety culture and positive safety attitudes. However, qualitative data indicated some important safety weaknesses and aspects that should be included in the process of evaluation of safety culture in organisations.

National report of the Slovak Republic. Compiled according to the terms of the convention on nuclear safety, June 2010

International Nuclear Information System (INIS)

Balaj, J.; Homola, J.; Rovny, J.; Metke, E.; Zemanova, D.; Grebeciova, J.; Turner, M.; Pospisil, M.; Bystricka, S.; Jurina, V.; Rovny, I.; Soltes, L.; Husarova, M.; Petrovic, J.; Fazekasova, H.; Zizkova, D.; Vagac, M.; Maudry, J.; Hacaj, A.; Betak, A.; Barbaric, M.

2010-06-01

A brief safety report of the Slovak Republic in 2010 is presented. A account of activities carried out by the Nuclear Regulatory Authority of the Slovak Republic (UJD) is presented.These activities are reported under the headings: (1) Introduction; (2) Nuclear installations in Slovak Republic in terms of the convention; (3) Legislation and regulation; (4) General safety aspects; (5) Safety of nuclear installations in Slovakia; ((6) Annexes; (6.1) List of nuclear installations and technical and economic indicators; (6.2) Selected generally binding legal regulations and safety guidelines in relation to nuclear and radiation safety; (6.3) List of selected national and international documents applicable to safety of nuclear installations; (6.4) Limits for radioactive discharges; (6.5) Team of authors.

Laboratory Safety Awareness Among General Physics Undergraduate Students

Directory of Open Access Journals (Sweden)

C. O. Ponferrada

2017-12-01

Full Text Available Safety awareness in the laboratory is essential to reduce occupational risks. This study was conducted to determine the students’ safety awareness in a Physics laboratory. This study determined the student perception towards safety awareness by factors of gender and college from which students are enrolled. A sum of 324 students enrolled in Physics10 (Mechanics and Heat and Physics11 (Electricity and Magnetism in the Mindanao University of Science and Technology (MUST were randomly selected as survey respondents. A modified survey questionnaire was used as research instrument. The results show that the students had positive level of safety awareness and perceived positively on the preventive measures to reduce laboratory risk. Further, regardless of gender students enrolled in Physics 10 were more positively aware towards safety awareness than students enrolled in Physics 11. Similarly, a variation among the students perception towards safety awareness from the College of Engineering and Architecture (CEA and College of Industrial and Information Technology (CIIT occurred. Overall, present findings indicate a need to introduce laboratory safety awareness in Physics classes.

IAEA coordinated research project (CRP). The use of selected safety indicators (concentrations, fluxes) in the assessment of radioactive waste disposal. Report 8: Natural uranium fluxes and their use in repository safety assesment - implications for coupled model development

International Nuclear Information System (INIS)

Read, D.

2003-01-01

An international research project has been established by the IAEA to evaluate the potential of natural radioelement concentrations and fluxes as alternative safety indicators in the assessment of radioactive waste disposal. The Finnish regulatory agency STUK is contributing to this study in the form of a report series dealing specifically with geochemical and hydrological recycling of trace elements in the stable Fennoscandian shield environment. In parallel, STUK has embarked on the development of a coupled chemical transport model based on previous work undertaken in Russia. The two initiatives are closely linked and should provide STUK with many of the tools necessary for evaluating future Posiva submissions. In order to prepare for these activities, the information required for modelling needs to be specified and the application methodology refined. This report examines the major factors that will need to be considered. Implicit in the approach is the requirement for formal testing against data from geochemical systems, including uranium-thorium ore bodies and emissions from groundwater springs and thermal spas. Although many natural analogue projects have been undertaken over the years, few of these studies specifically formulated the link to safety assessment and not all are directly applicable to the Finnish case. Nevertheless, there is a considerable body of data available from Finland, much of which has yet to be processed. A comprehensive data set exists for Palmottu and is now being re-examined to ensure that it can be exploited to its full potential. The Cu-U deposit at Hyrkkoelae provides a useful adjunct. Quantifying the effects of a repository heat source emplaced in a region of low ambient geothermal gradient is difficult. Recourse will necessarily be made to investigations at thermal spas elsewhere in Europe but first the transferability of these data needs to be assessed. The usefulness of natural indicators extends well beyond comparison of

The selection of field component reliability data for use in nuclear safety studies

International Nuclear Information System (INIS)

Coxson, B.A.; Tabaie, Mansour

1990-01-01

The paper reviews the user requirements for field component failure data in nuclear safety studies, and the capability of various data sources to satisfy these requirements. Aspects such as estimating the population of items exposed to failure, incompleteness, and under-reporting problems are discussed. The paper takes as an example the selection of component reliability data for use in the Pre-Operational Safety Report (POSR) for Sizewell 'B' Power Station, where field data has in many cases been derived from equipment other than that to be procured and operated on site. The paper concludes that the main quality sought in the available data sources for such studies is the ability to examine failure narratives in component reliability data systems for equipment performing comparable duties to the intended plant application. The main benefit brought about in the last decade is the interactive access to data systems which are adequately structured with regard to the equipment covered, and also provide a text-searching capability of quality-controlled event narratives. (author)

Statin Selection in Qatar Based on Multi-indication Pharmacotherapeutic Multi-criteria Scoring Model, and Clinician Preference.

Science.gov (United States)

Al-Badriyeh, Daoud; Fahey, Michael; Alabbadi, Ibrahim; Al-Khal, Abdullatif; Zaidan, Manal

2015-12-01

Statin selection for the largest hospital formulary in Qatar is not systematic, not comparative, and does not consider the multi-indication nature of statins. There are no reports in the literature of multi-indication-based comparative scoring models of statins or of statin selection criteria weights that are based primarily on local clinicians' preferences and experiences. This study sought to comparatively evaluate statins for first-line therapy in Qatar, and to quantify the economic impact of this. An evidence-based, multi-indication, multi-criteria pharmacotherapeutic model was developed for the scoring of statins from the perspective of the main health care provider in Qatar. The literature and an expert panel informed the selection criteria of statins. Relative weighting of selection criteria was based on the input of the relevant local clinician population. Statins were comparatively scored based on literature evidence, with those exceeding a defined scoring threshold being recommended for use. With 95% CI and 5% margin of error, the scoring model was successfully developed. Selection criteria comprised 28 subcriteria under the following main criteria: clinical efficacy, best publish evidence and experience, adverse effects, drug interaction, dosing time, and fixed dose combination availability. Outcome measures for multiple indications were related to effects on LDL cholesterol, HDL cholesterol, triglyceride, total cholesterol, and C-reactive protein. Atorvastatin, pravastatin, and rosuvastatin exceeded defined pharmacotherapeutic thresholds. Atorvastatin and pravastatin were recommended as first-line use and rosuvastatin as a nonformulary alternative. It was estimated that this would produce a 17.6% cost savings in statins expenditure. Sensitivity analyses confirmed the robustness of the evaluation's outcomes against input uncertainties. Incorporating a comparative evaluation of statins in Qatari practices based on a locally developed, transparent, multi-indication

Efficacy and safety of direct oral anticoagulants approved for cardiovascular indications: Systematic review and meta-analysis.

Directory of Open Access Journals (Sweden)

Raghavendra Charan P Makam

Full Text Available Direct oral anticoagulants (DOACs have emerged as promising alternatives to vitamin K antagonists (VKAs for patients with non-valvular atrial fibrillation (NVAF or venous thromboembolism (VTE. Few meta-analyses have included all DOACs that have received FDA approval for these cardiovascular indications, and their overall comparisons against VKAs have shortcomings in data and methods. We provide an updated overall assessment of the efficacy and safety of those DOACs at dosages currently approved for NVAF or VTE, in comparison with VKAs.We used data from Phase 3 randomized trials that compared an FDA-approved DOAC with VKA for primary prevention of stroke in patients with NVAF or for treatment of acute VTE.Among trial participants with NVAF, DOAC recipients had a lower risk of stroke or systemic embolism [Pooled Odds Ratio (OR 0.76, 95% Confidence Interval (CI (0.68-0.84], any stroke (0.80, 0.73-0.88, systemic embolism (0.56, 0.34-0.93, and total mortality (0.89, 0.84-0.95. Safety outcomes also showed a lower risk of fatal, major, and intracranial bleeding but higher risk for gastrointestinal bleeding (GIB. Patients with acute VTE randomized to DOACs had comparable risk of recurrent VTE and death (OR 0.88, 95% CI 0.75-1.03, recurrent DVT (0.83, 0.66-1.05, recurrent non-fatal PE (0.97, 0.75-1.25, and total mortality (0.94, 0.79-1.12. Safety outcomes for DOACs showed a lower risk of major, fatal, and intracranial bleeding, but similar risk of GIB.Patients receiving DOACs for NVAF had predominantly superior efficacy and safety. Patients who were treated with DOACs for acute VTE had non-inferior efficacy, but an overall superior safety profile.

Safety performance monitoring of autonomous marine systems

International Nuclear Information System (INIS)

Thieme, Christoph A.; Utne, Ingrid B.

2017-01-01

The marine environment is vast, harsh, and challenging. Unanticipated faults and events might lead to loss of vessels, transported goods, collected scientific data, and business reputation. Hence, systems have to be in place that monitor the safety performance of operation and indicate if it drifts into an intolerable safety level. This article proposes a process for developing safety indicators for the operation of autonomous marine systems (AMS). The condition of safety barriers and resilience engineering form the basis for the development of safety indicators, synthesizing and further adjusting the dual assurance and the resilience based early warning indicator (REWI) approaches. The article locates the process for developing safety indicators in the system life cycle emphasizing a timely implementation of the safety indicators. The resulting safety indicators reflect safety in AMS operation and can assist in planning of operations, in daily operational decision-making, and identification of improvements. Operation of an autonomous underwater vehicle (AUV) exemplifies the process for developing safety indicators and their implementation. The case study shows that the proposed process leads to a comprehensive set of safety indicators. It is expected that application of the resulting safety indicators consequently will contribute to safer operation of current and future AMS. - Highlights: • Process for developing safety indicators for autonomous marine systems. • Safety indicators based on safety barriers and resilience thinking. • Location of the development process in the system lifecycle. • Case study on AUV demonstrating applicability of the process.

Assessing Risk-Based Performance Indicators in Safety-Critical Systems for Nuclear Power Plants

OpenAIRE

TONT Gabriela

2011-01-01

The paper proposes framework for a multidisciplinary nuclear risk and safety assessment by modeling uncertainty and combining diverse evidence provided in such a way that it could be used to represent an entire argument about a system's dependability. The identified safety issues are being treated by means of probabilistic safety assessment (PSA). The behavior simulation of power plant in thepresence of risk factors is analyzed from the vulnerability, risk and functional safety viewpoints, hi...

Selection methodology for LWR safety programs and proposals. Volume 2. Methodology application

International Nuclear Information System (INIS)

Ritzman, R.L.; Husseiny, A.A.

1980-08-01

The results of work done to update and apply a methodology for selecting (prioritizing) LWR safety technology R and D programs are described. The methodology is based on multiattribute utility (MAU) theory. Application of the methodology to rank-order a group of specific R and D programs included development of a complete set of attribute utility functions, specification of individual attribute scaling constants, and refinement and use of an interactive computer program (MAUP) to process decision-maker inputs and generate overall (multiattribute) program utility values. The output results from several decision-makers are examined for consistency and conclusions and recommendations regarding general use of the methodology are presented. 3 figures, 18 tables

Experimental justification of indicative microbiological values for the safety of water bodies in the recreation areas

Directory of Open Access Journals (Sweden)

Е.V. Drozdova

2015-03-01

Full Text Available The article provides the assessment of the microbiological values of water bodies if they are used for recreational purposes and distinguishes the epidemiologically significant parameters. In order to validate the indicative safety values taking into account the existing conditions of the recreational use of water we conducted the hygienic assessment of water in the water bodies used for recreational purposes under the indicative microbiological values (total microbial count, thermotolerant coliform bacteria, E. coli; enterococcus, spores of sulfite-reducing Clostridia; coliphages; Ps. aeruginosa and the content of pathogenic microorganisms; also the microbiological profile of water was identified. The obtained data will be used to improve the system for monitoring of water bodies in the recreation areas.

PCI in Patients Supported With CF-LVADs: Indications, Safety, and Outcomes.

Science.gov (United States)

Anyanwu, Emeka C; Ota, Takeyoshi; Sayer, Gabriel; Nathan, Sandeep; Jeevanandam, Valluvan; Shah, Atman; Uriel, Nir

2016-06-01

Patients with heart failure supported with left ventricular assist devices (LVADs) may require coronary intervention during their support. This case series seeks to explore the indications, safety, and outcomes of percutaneous coronary intervention (PCI) in this population. Electronic medical records of patients with LVADs undergoing PCI at a large academic medical center were reviewed. Demographics, reason for PCI, procedural success, complications, and outcomes were collected. From 2010-2014, a total of 6 patients underwent PCI post LVAD implantation. Three patients had PCI in the early postimplantation period (1-3 days post LVAD implantation) while the other three received it later in the LVAD support period. Three indications for PCI were found in the reviewed cases: right ventricular failure (right coronary artery stenting), bridge to left ventricular recovery, and ventricular tachycardia (VT) storm. All patients were maintained on triple blood thinning therapy (aspirin, clopidogrel, and warfarin). There were no acute complications during the interventions; however, 2 patients died in the early intervention period and 2 died much later. The 2 deaths in the early intervention period were related to fatal gastrointestinal bleeding while on dual-antiplatelet therapy and warfarin, and intractable VT that PCI did not correct. The 2 deaths in the late postintervention period occurred due to unknown causes nearly 1 and 2 years post intervention, respectively. PCI was performed in patients with continuous-flow LVAD with several possible indications and without acute complications. The utility of PCI in this patient population, however, is likely limited by the risk of bleeding related to combined antiplatelet and anticoagulation therapies as well as lack of immediate apparent benefit. Further studies are necessary to better characterize this risk as well as quantify any potential long-term benefits.

Impact of ITER liquid metal design options on safety level and licensing - Sweden

International Nuclear Information System (INIS)

Harfors, C.; Devell, L.; Johansson, Kjell; Lundell, B.; Rolandsson, S.

1993-01-01

The safety level and licensability of five design options for ITER coolant, breeding material and structural material are assessed, with emphasis on some specified accident scenarios. The safety level is assessed in terms of barrier requirements and the feasibility to construct and qualify such a barrier. The licensability in Sweden of each design option is assessed based on the indicated safety level and on a judgement of the technical feasibility to construct and qualify the ITER tokamak itself, based on the selected design option. 20 refs

Integrated safety assessment report: Integrated Safety Assessment Program: Millstone Nuclear Power Station, Unit 1 (Docket No. 50-245): Draft report

International Nuclear Information System (INIS)

1987-04-01

The Integrated Safety Assessment Program (ISAP) was initiated in November 1984, by the US Nuclear Regulatory Commission to conduct integrated assessments for operating nuclear power reactors. The integrated assessment is conducted in a plant-specific basis to evaluate all licensing actions, licensee initiated plant improvements and selected unresolved generic/safety issues to establish implementation schedules for each item. In addition, procedures will be established to allow for a periodic updating of the schedules to account for licensing issues that arise in the future. This report documents the review of Millstone Nuclear Power Station, Unit No. 1, operated by Northeast Nuclear Energy Company (located in Waterford, Connecticut). Millstone Nuclear Power Station, Unit No. 1, is one of two plants being reviewed under the pilot program for ISAP. This report indicates how 85 topics selected for review were addressed. This report presents the staff's recommendations regarding the corrective actions to resolve the 85 topics and other actions to enhance plant safety. The report is being issued in draft form to obtain comments from the licensee, nuclear safety experts, and the Advisory Committee for Reactor Safeguards (ACRS). Once those comments have been resolved, the staff will present its positions, along with a long-term implementation schedule from the licensee, in the final version of this report

Selecting an Architecture for a Safety-Critical Distributed Computer System with Power, Weight and Cost Considerations

Science.gov (United States)

Torres-Pomales, Wilfredo

2014-01-01

This report presents an example of the application of multi-criteria decision analysis to the selection of an architecture for a safety-critical distributed computer system. The design problem includes constraints on minimum system availability and integrity, and the decision is based on the optimal balance of power, weight and cost. The analysis process includes the generation of alternative architectures, evaluation of individual decision criteria, and the selection of an alternative based on overall value. In this example presented here, iterative application of the quantitative evaluation process made it possible to deliberately generate an alternative architecture that is superior to all others regardless of the relative importance of cost.

Establishing Effective Environmental and Safety Performance Indicators: A Best Practice Approach in Uranium Production

International Nuclear Information System (INIS)

Rezansoff, D.; White, G.

2010-01-01

Cameco Corporation (Cameco), with headquarters in Saskatoon, Saskatchewan, Canada, is the world's largest, low-cost uranium producer, currently supplying sufficient uranium to meet 20% of the world's demand. It is characterized by a diverse range of operations in Canada, the United States and Central Asia, for which Cameco is the majority owner and/or operator, including exploration, mining, milling, refining and conversion. Cameco had four business segments: Uranium; Conversion services; Nuclear energy generation; and Gold Also, in 2002, Cameco revised its vision statement to indicate, 'Cameco will be a dominant nuclear energy company producing uranium fuel and generating clean electricity'. Commensurate with this, Cameco has re-confirmed its overall measures of success as follows: A safe, healthy and rewarding workplace; A clean environment; Supportive communities; and Solid financial performance - all reflected in a growing return to shareholders. Like most organizations, Cameco recognizes the importance of conducting its operations in ways that promote continual improvement in environmental and safety performance. Demonstrating the environmental advantages of nuclear is a vital part of the overall best management practices approach. Detractors often try to point to the uranium production side of the nuclear fuel cycle in pursuit of trying to make the case that the nuclear option does not carry any special environmental advantage. These attempts are mostly based on performance from eras past, not modern performance. The uranium sector must be able to present its case in a modern context, which is largely based on sustainable development principles. This paper focuses on establishing environment and safety performance indicators for the uranium production and conversion aspects of Cameco's business, as well as in support of the environmental advantages of nuclear energy generation

Improving safety culture through the health and safety organization: a case study.

Science.gov (United States)

Nielsen, Kent J

2014-02-01

International research indicates that internal health and safety organizations (HSO) and health and safety committees (HSC) do not have the intended impact on companies' safety performance. The aim of this case study at an industrial plant was to test whether the HSO can improve company safety culture by creating more and better safety-related interactions both within the HSO and between HSO members and the shop-floor. A quasi-experimental single case study design based on action research with both quantitative and qualitative measures was used. Based on baseline mapping of safety culture and the efficiency of the HSO three developmental processes were started aimed at the HSC, the whole HSO, and the safety representatives, respectively. Results at follow-up indicated a marked improvement in HSO performance, interaction patterns concerning safety, safety culture indicators, and a changed trend in injury rates. These improvements are interpreted as cultural change because an organizational double-loop learning process leading to modification of the basic assumptions could be identified. The study provides evidence that the HSO can improve company safety culture by focusing on safety-related interactions. © 2013. Published by Elsevier Ltd and National Safety Council.

Processes on Uncontrolled Aerodromes and Safety Indicators - Part I

Directory of Open Access Journals (Sweden)

Vladimír Plos

2013-09-01

Full Text Available This article describes the processes that take place at the beginning of each duty of dispatcher at uncontrolled aerodromes.Thanks to modeling and analysis of these processes, there is a possible to find critical ones and implement precise targeted safety measures.

Selected component failure rate values from fusion safety assessment tasks

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, L.C.

1998-09-01

This report is a compilation of component failure rate and repair rate values that can be used in magnetic fusion safety assessment tasks. Several safety systems are examined, such as gas cleanup systems and plasma shutdown systems. Vacuum system component reliability values, including large vacuum chambers, have been reviewed. Values for water cooling system components have also been reported here. The report concludes with the examination of some equipment important to personnel safety, atmospheres, combustible gases, and airborne releases of radioactivity. These data should be useful to system designers to calculate scoping values for the availability and repair intervals for their systems, and for probabilistic safety or risk analysts to assess fusion systems for safety of the public and the workers.

Selected Component Failure Rate Values from Fusion Safety Assessment Tasks

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, Lee Charles

1998-09-01

This report is a compilation of component failure rate and repair rate values that can be used in magnetic fusion safety assessment tasks. Several safety systems are examined, such as gas cleanup systems and plasma shutdown systems. Vacuum system component reliability values, including large vacuum chambers, have been reviewed. Values for water cooling system components have also been reported here. The report concludes with the examination of some equipment important to personnel safety, atmospheres, combustible gases, and airborne releases of radioactivity. These data should be useful to system designers to calculate scoping values for the availability and repair intervals for their systems, and for probabilistic safety or risk analysts to assess fusion systems for safety of the public and the workers.

Selected component failure rate values from fusion safety assessment tasks

International Nuclear Information System (INIS)

Cadwallader, L.C.

1998-01-01

This report is a compilation of component failure rate and repair rate values that can be used in magnetic fusion safety assessment tasks. Several safety systems are examined, such as gas cleanup systems and plasma shutdown systems. Vacuum system component reliability values, including large vacuum chambers, have been reviewed. Values for water cooling system components have also been reported here. The report concludes with the examination of some equipment important to personnel safety, atmospheres, combustible gases, and airborne releases of radioactivity. These data should be useful to system designers to calculate scoping values for the availability and repair intervals for their systems, and for probabilistic safety or risk analysts to assess fusion systems for safety of the public and the workers

A study of software safety analysis system for safety-critical software

International Nuclear Information System (INIS)

Chang, H. S.; Shin, H. K.; Chang, Y. W.; Jung, J. C.; Kim, J. H.; Han, H. H.; Son, H. S.

2004-01-01

The core factors and requirements for the safety-critical software traced and the methodology adopted in each stage of software life cycle are presented. In concept phase, Failure Modes and Effects Analysis (FMEA) for the system has been performed. The feasibility evaluation of selected safety parameter was performed and Preliminary Hazards Analysis list was prepared using HAZOP(Hazard and Operability) technique. And the check list for management control has been produced via walk-through technique. Based on the evaluation of the check list, activities to be performed in requirement phase have been determined. In the design phase, hazard analysis has been performed to check the safety capability of the system with regard to safety software algorithm using Fault Tree Analysis (FTA). In the test phase, the test items based on FMEA have been checked for fitness guided by an accident scenario. The pressurizer low pressure trip algorithm has been selected to apply FTA method to software safety analysis as a sample. By applying CASE tool, the requirements traceability of safety critical system has been enhanced during all of software life cycle phases

Visual recognition of the load of roof-bolts by an indicator

Energy Technology Data Exchange (ETDEWEB)

Leonhardt, J. [Leon Industries (Germany)

2001-07-01

Hundreds of bolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to guard roof-bolt loads, to state weak points as well as to optimize the anchor density and the dimension. The bolt-indicator are mushroom shaped and are of coated metal. It is brought in between the anchor plate and the anchor mother. The loads appearing at the anchor will transfer to the bolt-indicators and can be recognized visually at the cylindrical part by the amount of the surface coating. A select example clarifies itself application aims, operation and a usage of the bolt-indicator and the yielding advantages in practice. (orig.)

Comparing Stream Discharge, Dissolved Organic Carbon, and Selected MODIS Indices in Freshwater Basins

Science.gov (United States)

Shaver, W. T.; Wollheim, W. M.

2009-12-01

In a preliminary study of the Ipswich Basin in Massachusetts, a good correlation was found to exist between the MODIS (Moderate Resolution Imaging Spectroradiometer) Enhanced Vegetation Index and stream dissolved organic carbon (DOC). Further study was warranted to determine the utility of MODIS indices in predicting temporal stream DOC. Stream discharge rates and DOC data were obtained from the USGS National Water Quality Assessment Program (NAWQA) database. Twelve NAWQA monitoring sites were selected for evaluation based on the criteria of having drainage basin sizes less than 600 km2 with relatively continuous, long-term DOC and discharge data. MODIS indices were selected based on their connections with terrestrial DOC and were obtained for each site's catchment area. These included the Normalized Vegetation Index (NDVI), the Enhanced Vegetation Index (EVI), the Daily Photosynthesis (PSN) and the Leaf Area Index (LAI). Regression analysis was used to evaluate the relationships between DOC, discharge and MODIS products. Data analysis revealed several important trends. Sites with strong positive correlation coefficients (r values ranging from 0.462 to 0.831) between DOC and discharge displayed weak correlations with all of the MODIS indices (r values ranging from 0 to 0.322). For sites where the DOC/discharge correlation was weak or negative, MODIS indices were moderately correlated, with r values ranging from 0.35 to 0.647, all of which were significant at less than 1 percent. Some sites that had weak positive correlations with MODIS indices displayed a lag time, that is, the MODIS index rose and fell shortly before the DOC concentration rose and fell. Shifting the MODIS data forward in time by roughly one month significantly increased the DOC/MODIS r values by about 10%. NDVI and EVI displayed the strongest correlations with temporal DOC variability (r values ranging from 0.471 to 0.647), and therefore these indices are the most promising for being incorporated

Selection of Surrogate Bacteria for Use in Food Safety Challenge Studies: A Review.

Science.gov (United States)

Hu, Mengyi; Gurtler, Joshua B

2017-09-01

Nonpathogenic surrogate bacteria are prevalently used in a variety of food challenge studies in place of foodborne pathogens such as Listeria monocytogenes, Salmonella, Escherichia coli O157:H7, and Clostridium botulinum because of safety and sanitary concerns. Surrogate bacteria should have growth characteristics and/or inactivation kinetics similar to those of target pathogens under given conditions in challenge studies. It is of great importance to carefully select and validate potential surrogate bacteria when verifying microbial inactivation processes. A validated surrogate responds similar to the targeted pathogen when tested for inactivation kinetics, growth parameters, or survivability under given conditions in agreement with appropriate statistical analyses. However, a considerable number of food studies involving putative surrogate bacteria lack convincing validation sources or adequate validation processes. Most of the validation information for surrogates in these studies is anecdotal and has been collected from previous publications but may not be sufficient for given conditions in the study at hand. This review is limited to an overview of select studies and discussion of the general criteria and approaches for selecting potential surrogate bacteria under given conditions. The review also includes a list of documented bacterial pathogen surrogates and their corresponding food products and treatments to provide guidance for future studies.

Developing Measures for Assessing the Causality of Safety Culture in a Petrochemical Industry

Energy Technology Data Exchange (ETDEWEB)

Wu, T.-C., E-mail: tcwu@sunrise.hk.edu.t [HungKuang University, Department of Safety, Health and Environmental Engineering (China); Lin, C.-H.; Shiau, S.-Y. [HungKuang University, Institute of Occupational Safety and Hazard Prevention (China)

2009-12-15

This paper discusses safety culture in the petrochemical sector and the causes and consequences of safety culture. A sample of 520 responses selected by simple random sampling completed questionnaires for this survey, the return rate was 86.75%. The research instrument comprises four sections: basic information, the safety leadership scale (SLS), the safety climate scale (SCS), and the safety performance scale (SPS). SPSS 12.0, a statistical software package, was used for item analysis, validity analysis, and reliability analysis. Exploratory factor analysis indicated that (1) SLS abstracted three factors such as safety caring, safety controlling, and safety coaching; (2) SCS comprised three factors such as emergency response, safety commitment, and risk perception; and (3) SPS was composed of accident investigation, safety training, safety inspections, and safety motivation. We conclude that the SLS, SCS, and SPS developed in this paper have good construct validity and internal consistency and can serve as the basis for future research.

Developing Measures for Assessing the Causality of Safety Culture in a Petrochemical Industry

International Nuclear Information System (INIS)

Wu, T.-C.; Lin, C.-H.; Shiau, S.-Y.

2009-01-01

This paper discusses safety culture in the petrochemical sector and the causes and consequences of safety culture. A sample of 520 responses selected by simple random sampling completed questionnaires for this survey, the return rate was 86.75%. The research instrument comprises four sections: basic information, the safety leadership scale (SLS), the safety climate scale (SCS), and the safety performance scale (SPS). SPSS 12.0, a statistical software package, was used for item analysis, validity analysis, and reliability analysis. Exploratory factor analysis indicated that (1) SLS abstracted three factors such as safety caring, safety controlling, and safety coaching; (2) SCS comprised three factors such as emergency response, safety commitment, and risk perception; and (3) SPS was composed of accident investigation, safety training, safety inspections, and safety motivation. We conclude that the SLS, SCS, and SPS developed in this paper have good construct validity and internal consistency and can serve as the basis for future research.

Selective Sequential Zero-Base Budgeting Procedures Based on Total Factor Productivity Indicators

OpenAIRE

A. Ishikawa; E. F. Sudit

1981-01-01

The authors' purpose in this paper is to develop productivity-based sequential budgeting procedures designed to expedite identification of major problem areas in bugetary performance, as well as to reduce the costs associated with comprehensive zero-base analyses. The concept of total factor productivity is reviewed and its relations to ordinary and zero-based budgeting are discussed in detail. An outline for a selective sequential analysis based on monitoring of three key indicators of (a) i...

National Waste Repository Novi Han operational safety analysis report. Safety assessment methodology

International Nuclear Information System (INIS)

2003-01-01

The scope of the safety assessment (SA), presented includes: waste management functions (acceptance, conditioning, storage, disposal), inventory (current and expected in the future), hazards (radiological and non-radiological) and normal and accidental modes. The stages in the development of the SA are: criteria selection, information collection, safety analysis and safety assessment documentation. After the review the facilities functions and the national and international requirements, the criteria for safety level assessment are set. As a result from the 2nd stage actual parameters of the facility, necessary for safety analysis are obtained.The methodology is selected on the base of the comparability of the results with the results of previous safety assessments and existing standards and requirements. The procedure and requirements for scenarios selection are described. A radiological hazard categorisation of the facilities is presented. Qualitative hazards and operability analysis is applied. The resulting list of events are subjected to procedure for prioritization by method of 'criticality analysis', so the estimation of the risk is given for each event. The events that fall into category of risk on the boundary of acceptability or are unacceptable are subjected to the next steps of the analysis. As a result the lists with scenarios for PSA and possible design scenarios are established. PSA logical modeling and quantitative calculations of accident sequences are presented

Defining safety culture and the nexus between safety goals and safety culture. 1. An Investigation Study on Practical Points of Safety Management

International Nuclear Information System (INIS)

Hasegawa, Naoko; Takano, Kenichi; Hirose, Ayako

2001-01-01

In a report after the Chernobyl accident, the International Atomic Energy Agency indicated the definition and the importance of safety culture and the ideal organizational state where safety culture pervades. However, the report did not mention practical approaches to enhance safety culture. In Japan, although there had been investigations that clarified the consciousness of employees and the organizational climate in the nuclear power and railway industries, organizational factors that clarified the level of organization safety and practical methods that spread safety culture in an organization had not been studied. The Central Research Institute of the Electric Power Industry conducted surveys of organizational culture for the construction, chemical, and manufacturing industries. The aim of our study was to clarify the organizational factors that influence safety in an organization expressed in employee safety consciousness, commitment to safety activities, rate of accidents, etc. If these areas were clarified, the level of organization safety might be evaluated, and practical ways could be suggested to enhance the safety culture. Consequently, a series of investigations was conducted to clarify relationships among organizational climate, employee consciousness, safety management and activities, and rate of accidents. The questionnaire surveys were conducted in 1998-1999. The subjects were (a) managers of the safety management sections in the head offices of the construction, chemical, and manufacturing industries; (b) responsible persons in factories of the chemical and manufacturing industries; and (c) general workers in factories of the chemical and manufacturing industries. The number of collected data was (a) managers in the head office: 48 from the construction industry and 58 from the chemical and manufacturing industries, (b) responsible persons in factories: 567, and (c) general workers: from 29 factories. Items in the questionnaires were selected from

Evaluation and selection of indicators for land degradation and desertification monitoring: methodological approach.

Science.gov (United States)

Kosmas, C; Kairis, Or; Karavitis, Ch; Ritsema, C; Salvati, L; Acikalin, S; Alcala, M; Alfama, P; Atlhopheng, J; Barrera, J; Belgacem, A; Solé-Benet, A; Brito, J; Chaker, M; Chanda, R; Coelho, C; Darkoh, M; Diamantis, I; Ermolaeva, O; Fassouli, V; Fei, W; Feng, J; Fernandez, F; Ferreira, A; Gokceoglu, C; Gonzalez, D; Gungor, H; Hessel, R; Juying, J; Khatteli, H; Khitrov, N; Kounalaki, A; Laouina, A; Lollino, P; Lopes, M; Magole, L; Medina, L; Mendoza, M; Morais, P; Mulale, K; Ocakoglu, F; Ouessar, M; Ovalle, C; Perez, C; Perkins, J; Pliakas, F; Polemio, M; Pozo, A; Prat, C; Qinke, Y; Ramos, A; Ramos, J; Riquelme, J; Romanenkov, V; Rui, L; Santaloia, F; Sebego, R; Sghaier, M; Silva, N; Sizemskaya, M; Soares, J; Sonmez, H; Taamallah, H; Tezcan, L; Torri, D; Ungaro, F; Valente, S; de Vente, J; Zagal, E; Zeiliguer, A; Zhonging, W; Ziogas, A

2014-11-01

An approach to derive relationships for defining land degradation and desertification risk and developing appropriate tools for assessing the effectiveness of the various land management practices using indicators is presented in the present paper. In order to investigate which indicators are most effective in assessing the level of desertification risk, a total of 70 candidate indicators was selected providing information for the biophysical environment, socio-economic conditions, and land management characteristics. The indicators were defined in 1,672 field sites located in 17 study areas in the Mediterranean region, Eastern Europe, Latin America, Africa, and Asia. Based on an existing geo-referenced database, classes were designated for each indicator and a sensitivity score to desertification was assigned to each class based on existing research. The obtained data were analyzed for the various processes of land degradation at farm level. The derived methodology was assessed using independent indicators, such as the measured soil erosion rate, and the organic matter content of the soil. Based on regression analyses, the collected indicator set can be reduced to a number of effective indicators ranging from 8 to 17 in the various processes of land degradation. Among the most important indicators identified as affecting land degradation and desertification risk were rain seasonality, slope gradient, plant cover, rate of land abandonment, land-use intensity, and the level of policy implementation.

Genomic selection using indicator traits to reduce the environmental impact of milk production

DEFF Research Database (Denmark)

Hansen Axelsson, H; Fikse, W F; Kargo, Morten

2013-01-01

The aim of this simulation study was to test the hypothesis that phenotype information of specific indicator traits of environmental importance recorded on a small-scale can be implemented in breeding schemes with genomic selection to reduce the environmental impact of milk production. A stochastic...... was, however, best in the scenarios where the genetic correlation between IT and EI was ≥0.30 and the accuracy of direct genomic value was ≥0.40. The genetic gain in EI was 26 to 34% higher when indicator traits such as greenhouse gases in the breath of the cow and methane recorded in respiration...... of direct genomic values will be reasonably high...

Safety class methodology

International Nuclear Information System (INIS)

Donner, E.B.; Low, J.M.; Lux, C.R.

1992-01-01

DOE Order 6430.1A, General Design Criteria (GDC), requires that DOE facilities be evaluated with respect to ''safety class items.'' Although the GDC defines safety class items, it does not provide a methodology for selecting safety class items. The methodology described in this paper was developed to assure that Safety Class Items at the Savannah River Site (SRS) are selected in a consistent and technically defensible manner. Safety class items are those in the highest of four categories determined to be of special importance to nuclear safety and, merit appropriately higher-quality design, fabrication, and industrial test standards and codes. The identification of safety class items is approached using a cascading strategy that begins at the 'safety function' level (i.e., a cooling function, ventilation function, etc.) and proceeds down to the system, component, or structure level. Thus, the items that are required to support a safety function are SCls. The basic steps in this procedure apply to the determination of SCls for both new project activities, and for operating facilities. The GDC lists six characteristics of SCls to be considered as a starting point for safety item classification. They are as follows: 1. Those items whose failure would produce exposure consequences that would exceed the guidelines in Section 1300-1.4, ''Guidance on Limiting Exposure of the Public,'' at the site boundary or nearest point of public access 2. Those items required to maintain operating parameters within the safety limits specified in the Operational Safety Requirements during normal operations and anticipated operational occurrences. 3. Those items required for nuclear criticality safety. 4. Those items required to monitor the release of radioactive material to the environment during and after a Design Basis Accident. Those items required to achieve, and maintain the facility in a safe shutdown condition 6. Those items that control Safety Class Item listed above

Factors influencing safety in a sample of marked pedestrian crossings selected for safety inspections in the city of Oslo.

Science.gov (United States)

Elvik, Rune; Sørensen, Michael W J; Nævestad, Tor-Olav

2013-10-01

This paper reports an analysis of factors influencing safety in a sample of marked pedestrian crossings in the city of Oslo, Norway. The sample consists of 159 marked pedestrian crossings where a total of 316 accidents were recorded during a period of five years. The crossings were selected for inspection because of they were, for various reasons, regarded as sub-standard. The sample of crossings is therefore not representative of all pedestrian crossings in Oslo. Factors influencing the number of accidents were studied by means of negative binomial regression. Factors that were studied included the volume of pedestrians and vehicles, the number of traffic lanes at the crossing, the location of the crossing (midblock or junction), the type of traffic control, the share of pedestrians using the crossing and the speed of approaching vehicles. The analysis confirmed the presence of a "safety-in-numbers" effect, meaning that an increase in the number of pedestrians is associated with a lower risk of accident for each pedestrian. Crossings located in four-leg junctions or roundabouts had more accidents than crossings located in three-leg junctions or on sections between junctions. A high share of pedestrians crossing the road outside the marked crossing was associated with a high number of accidents. Increased speed was associated with an increased number of accidents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparison of selected indicators of the environment in regions of the Slovak Republic to 2002

International Nuclear Information System (INIS)

Proksa, P.; Rolkova, M.; Bracinikova, J.; Gajdos, L.; Hajnikova, M.; Jecmenova, I.; Kanianska, R.; Knazovicka, J.; Kovalova, A.

2003-01-01

In this report the selected indicators of the environment in regions of the Slovak Republic to 2002 are compared. In this report the following indicators are reviewed: Air; Water; Ground environment; Soils; Flora; Nature heritage and their protection; Demography; Industry; Influence of mining on the environment; Energetics, heating and gas industry; Agriculture and forestry; Recreation and tourist traffic; Public health; Physical and chemical risk factors; Waste management; Accidents and disaster damages

Routine maintenance: safety term based work selection; Selecao de trabalho baseado no prazo seguro

Energy Technology Data Exchange (ETDEWEB)

Camargo, Albair de; Filho, Antnio S.; Brendler, Fabiano E.; Adamatti, Gilberto A.; Naruto, Itiro; Araujo, Luiz C.F.; Puerari, Roberto [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2004-07-01

This work has objective to present the experience of improvement of routine maintenance system in some refineries of the PETROBRAS system, with the purpose to increase the efficiency in the Industrial Maintenance Management (cost), Utilization and HSE (Health, Safety and Environment), key of success of a petroleum company. The new system is based on the implantation of the culture of work selection in the safe period, through elaboration of new maintenance procedure, with emphasis in decisions shared between Operation and Maintenance Team, resulting in reduction of emergencies, making possible contract of services of maintenance for packages and improved allocation of resources. This work treat about improvement of the system in use, in view of that it has already taken in consideration the consequence of fail in the maintenance with participation of the operators. Besides of these challenge, this modification was made without causing riots in the process of implantation of SAP. As main result, financial profits had got better of resources with increase of safety, considering that they are analyzed in a way it that systematized potential risks. (author)

Experience with performance based training of nuclear criticality safety engineers

International Nuclear Information System (INIS)

Taylor, R.G.

1993-01-01

For non-reactor nuclear facilities, the U.S. Department of Energy (DOE) does not require that nuclear criticality safety engineers demonstrate qualification for their job. It is likely, however, that more formalism will be required in the future. Current DOE requirements for those positions which do have to demonstrate qualification indicate that qualification should be achieved by using a systematic approach such as performance based training (PBT). Assuming that PBT would be an acceptable mechanism for nuclear criticality safety engineer training in a more formal environment, a site-specific analysis of the nuclear criticality safety engineer job was performed. Based on this analysis, classes are being developed and delivered to a target audience of newer nuclear criticality safety engineers. Because current interest is in developing training for selected aspects of the nuclear criticality safety engineer job, the analysis is incompletely developed in some areas

Safety in construction?

NARCIS (Netherlands)

Swuste, P.H.J.J.

2013-01-01

The available literature on Construction Safety is not very optimistic about the chances of evidence-based safety in the construction industry exerting a positive influence. Many articles indicate that the structures and processes that are designed to ensure safety in the industry are poor. Safety

Initial development of a practical safety audit tool to assess fleet safety management practices.

Science.gov (United States)

Mitchell, Rebecca; Friswell, Rena; Mooren, Lori

2012-07-01

Work-related vehicle crashes are a common cause of occupational injury. Yet, there are few studies that investigate management practices used for light vehicle fleets (i.e. vehicles less than 4.5 tonnes). One of the impediments to obtaining and sharing information on effective fleet safety management is the lack of an evidence-based, standardised measurement tool. This article describes the initial development of an audit tool to assess fleet safety management practices in light vehicle fleets. The audit tool was developed by triangulating information from a review of the literature on fleet safety management practices and from semi-structured interviews with 15 fleet managers and 21 fleet drivers. A preliminary useability assessment was conducted with 5 organisations. The audit tool assesses the management of fleet safety against five core categories: (1) management, systems and processes; (2) monitoring and assessment; (3) employee recruitment, training and education; (4) vehicle technology, selection and maintenance; and (5) vehicle journeys. Each of these core categories has between 1 and 3 sub-categories. Organisations are rated at one of 4 levels on each sub-category. The fleet safety management audit tool is designed to identify the extent to which fleet safety is managed in an organisation against best practice. It is intended that the audit tool be used to conduct audits within an organisation to provide an indicator of progress in managing fleet safety and to consistently benchmark performance against other organisations. Application of the tool by fleet safety researchers is now needed to inform its further development and refinement and to permit psychometric evaluation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Nuclear safety review for the year 2001

International Nuclear Information System (INIS)

2002-07-01

The Nuclear Safety Review for the Year 2001 reports on worldwide efforts to strengthen nuclear and radiation safety, including radioactive waste safety. It is in three parts. Part 1 describes those events in 2001 that have, or may have, significance for nuclear, radiation and waste safety worldwide. It includes developments such as new initiatives in international cooperation, events of safety significance and events that may be indicative of trends in safety. Part 2 describes some of the IAEA's efforts to strengthen international co-operation in nuclear, radiation and waste safety during 2001. It covers legally binding international agreements, non-binding safety standards, and provisions for the application of safety standards. This is done in a very brief manner, because these issues are addressed in more detail in the Agency's Annual Report for 2001. Part 3 presents a brief look ahead to some issues that are likely to be prominent in the coming year(s). The topics covered were selected by the IAEA Secretariat on the basis of trends observed in recent years, account being taken of planned or expected future developments. A draft of the Nuclear Safety Review for the Year 2001 was presented to the March 2002 session of IAEA's Board of Governors. This final version has been prepared taking account of the discussion in the Board. In some places, information has been added to describe developments early in 2002 that were considered pertinent to the discussion of events during 2001

Indicators of Faculty and Staff Perceptions of Campus Safety: A Case Study

Science.gov (United States)

Woolfolk, Willie A.

2013-01-01

The study addressed the problem of a critical increase in campus crime between 1999 and 2009, a period during which overall crime in the United States declined. Further the research explored the perceptions of campus safety among faculty and staff at an institution where campus safety initiatives are nationally ranked as exemplary and incidents of…

Regional anesthesia for pediatric knee surgery: a review of the indications, procedures, outcomes, safety, and challenges

Directory of Open Access Journals (Sweden)

Muhly WT

2015-11-01

Full Text Available Wallis T Muhly, Harshad G Gurnaney, Arjunan GaneshDepartment of Anesthesiology and Critical Care Medicine, The Children’s Hospital of Philadelphia, Perelman School of Medicine at the University of Pennsylvania, Pennsylvania, PA, USAAbstract: The indications for surgery on the knee in children and adolescents share some similarity to adult practice in that there are an increasing number of sports-related injuries requiring surgical repair. In addition, there are some unique age-related conditions or congenital abnormalities that may present as indications for orthopedic intervention at the level of the knee. The efficacy and safety of peripheral nerve blocks (PNBs for postoperative analgesia following orthopedic surgery has been well established in adults. Recent studies have also demonstrated earlier functional recovery after surgery in patients who received PNBs. In children, PNB is gaining popularity, and increasing data are emerging to demonstrate the feasibility, efficacy, and safety in this population. In this paper, we will review some of the most common indications for surgery involving the knee in children and the anatomy of knee, associated dermatomal and osteotomal innervation, and the PNBs most commonly used to produce analgesia at the level of the knee. We will review the evidence in support of regional anesthesia in children in terms of both the quality conferred to the immediate postoperative care and the role of continuous PNBs in maintaining effective analgesia following discharge. Also we will discuss some of the subtle challenges in utilizing regional anesthesia in the pediatric patient including the use of general anesthesia when performing regional anesthesia and the issue of monitoring for compartment syndrome. Finally, we will offer some thoughts about areas of practice that are in need of further investigation.Keywords: pediatric surgery, regional anesthesia, analgesia, knee surgery

Comparing the cardiovascular therapeutic indices of glycopyrronium and tiotropium in an integrated rat pharmacokinetic, pharmacodynamic and safety model

International Nuclear Information System (INIS)

Trifilieff, Alexandre; Ethell, Brian T.; Sykes, David A.; Watson, Kenny J.; Collingwood, Steve; Charlton, Steven J.; Kent, Toby C.

2015-01-01

Long acting inhaled muscarinic receptor antagonists, such as tiotropium, are widely used as bronchodilator therapy for chronic obstructive pulmonary disease (COPD). Although this class of compounds is generally considered to be safe and well tolerated in COPD patients the cardiovascular safety of tiotropium has recently been questioned. We describe a rat in vivo model that allows the concurrent assessment of muscarinic antagonist potency, bronchodilator efficacy and a potential for side effects, and we use this model to compare tiotropium with NVA237 (glycopyrronium bromide), a recently approved inhaled muscarinic antagonist for COPD. Anaesthetized Brown Norway rats were dosed intratracheally at 1 or 6 h prior to receiving increasing doses of intravenous methacholine. Changes in airway resistance and cardiovascular function were recorded and therapeutic indices were calculated against the ED 50 values for the inhibition of methacholine-induced bronchoconstriction. At both time points studied, greater therapeutic indices for hypotension and bradycardia were observed with glycopyrronium (19.5 and 28.5 fold at 1 h; > 200 fold at 6 h) than with tiotropium (1.5 and 4.2 fold at 1 h; 4.6 and 5.5 fold at 6 h). Pharmacokinetic, protein plasma binding and rat muscarinic receptor binding properties for both compounds were determined and used to generate an integrated model of systemic M 2 muscarinic receptor occupancy, which predicted significantly higher M 2 receptor blockade at ED 50 doses with tiotropium than with glycopyrronium. In our preclinical model there was an improved safety profile for glycopyrronium when compared with tiotropium. - Highlights: • We use an in vivo rat model to study CV safety of inhaled muscarinic antagonists. • We integrate protein and receptor binding and PK of tiotropium and glycopyrrolate. • At ED 50 doses for bronchoprotection we model systemic M 2 receptor occupancy. • Glycopyrrolate demonstrates lower M 2 occupancy at

Comparing the cardiovascular therapeutic indices of glycopyrronium and tiotropium in an integrated rat pharmacokinetic, pharmacodynamic and safety model

Energy Technology Data Exchange (ETDEWEB)

Trifilieff, Alexandre; Ethell, Brian T. [Respiratory Disease Area, Novartis Institutes for Biomedical Research, Wimblehurst Road, Horsham, West Sussex RH12 5AB (United Kingdom); Sykes, David A. [Respiratory Disease Area, Novartis Institutes for Biomedical Research, Wimblehurst Road, Horsham, West Sussex RH12 5AB (United Kingdom); School of Life Sciences, Queen' s Medical Centre, University of Nottingham, Nottingham, NG7 2UH (United Kingdom); Watson, Kenny J.; Collingwood, Steve [Respiratory Disease Area, Novartis Institutes for Biomedical Research, Wimblehurst Road, Horsham, West Sussex RH12 5AB (United Kingdom); Charlton, Steven J. [Respiratory Disease Area, Novartis Institutes for Biomedical Research, Wimblehurst Road, Horsham, West Sussex RH12 5AB (United Kingdom); School of Life Sciences, Queen' s Medical Centre, University of Nottingham, Nottingham, NG7 2UH (United Kingdom); Kent, Toby C., E-mail: tobykent@me.com [Respiratory Disease Area, Novartis Institutes for Biomedical Research, Wimblehurst Road, Horsham, West Sussex RH12 5AB (United Kingdom)

2015-08-15

Long acting inhaled muscarinic receptor antagonists, such as tiotropium, are widely used as bronchodilator therapy for chronic obstructive pulmonary disease (COPD). Although this class of compounds is generally considered to be safe and well tolerated in COPD patients the cardiovascular safety of tiotropium has recently been questioned. We describe a rat in vivo model that allows the concurrent assessment of muscarinic antagonist potency, bronchodilator efficacy and a potential for side effects, and we use this model to compare tiotropium with NVA237 (glycopyrronium bromide), a recently approved inhaled muscarinic antagonist for COPD. Anaesthetized Brown Norway rats were dosed intratracheally at 1 or 6 h prior to receiving increasing doses of intravenous methacholine. Changes in airway resistance and cardiovascular function were recorded and therapeutic indices were calculated against the ED{sub 50} values for the inhibition of methacholine-induced bronchoconstriction. At both time points studied, greater therapeutic indices for hypotension and bradycardia were observed with glycopyrronium (19.5 and 28.5 fold at 1 h; > 200 fold at 6 h) than with tiotropium (1.5 and 4.2 fold at 1 h; 4.6 and 5.5 fold at 6 h). Pharmacokinetic, protein plasma binding and rat muscarinic receptor binding properties for both compounds were determined and used to generate an integrated model of systemic M{sub 2} muscarinic receptor occupancy, which predicted significantly higher M{sub 2} receptor blockade at ED{sub 50} doses with tiotropium than with glycopyrronium. In our preclinical model there was an improved safety profile for glycopyrronium when compared with tiotropium. - Highlights: • We use an in vivo rat model to study CV safety of inhaled muscarinic antagonists. • We integrate protein and receptor binding and PK of tiotropium and glycopyrrolate. • At ED{sub 50} doses for bronchoprotection we model systemic M{sub 2} receptor occupancy. • Glycopyrrolate demonstrates lower M

Development of future indications for BOTOX.

Science.gov (United States)

Brin, Mitchell F

2009-10-01

Since the late 1970s, local injections of BoNT have provided clinical benefit for patients with inappropriately contracting muscles with or without pain or sensory disturbance. Marketing authorization for some BoNTs, depending on country, include core indications of dystonia (blepharospasm and cervical dystonia), large muscle spastic disorders (not yet approved in the United States, e.g., adult post-stroke spasticity and equinus foot deformity), hyperhidrosis and aesthetic. Subsequent development has extended to selected conditions characterized by recurrent or chronic pain (migraine headache), and urologic indications (neurogenic/idiopathic overactive bladder; prostate hyperplasia), with multiple additional opportunities available. Portfolio management requires a careful individual opportunity assessment of scientific and technical aspects (basic science foundation, potential to treat unmet medical need, product-specific risk in specific populations, therapeutic margin/safety profile, and probability of successful registration pathway). This article describes ongoing development targets for BOTOX.

Safety enhancement concept for NPP of new generation with VVER reactors

International Nuclear Information System (INIS)

Bezlepkin, V.; Kukhtevich, I.; Semashko, S.; Svetlov, S.; Solodovnikov, A.

2004-01-01

With the present day conditions, in order to successfully promote new NPP designs in the electric power markets, it is necessary to ensure enhanced technical/economic performances provided that international safety requirements are properly adhered to. When compared with high-powered nuclear power plants, NPP VVER-640 design (medium powered) possesses a number of advantages for the regions with undeveloped energy systems. Reduced specific energy intensity of the core adopted in this type of reactor allows to ensure the emergency cooldown of the reactor plant by passive means and to minimize the 'human factor' risk and external effects and provide sound substantiations as to how to retain corium inside RPV in case of severe accidents. At the same time, high-powered NPPs seem to be promising for regions with developed energy systems. Among such designs, NPP VVER-1000 and VVER-1500 designs are the most desirable. Configuration of new generation NPP with VVER-1500 is to be selected based on the gained experience in designing NPPs of previous generations considering the latest safety requirements and situation in the domestic and global energy markets for the time being and in the short run. Recent IAEA publications and latest EUR requirements insist that the following key safety indices should be established for new NPP designs: - aggregated frequency of core melting is 10 -6 (1/year); - frequency of maximum accident release is 10 -7 (1/year). To meet the aforementioned criteria, it is necessary to implement some safety assurance principles recommended by IAEA (in-depth defence, single failure, redundancy, diversity, etc.), application of deterministic and probabilistic methods for selection of safety assurance activities and means and use of reasonable combination of active and passive systems. Application of VVER-640 concept to high-powered NPPs seems to be a formidable task due to a number of reasons, namely, it is quite difficult to carry out cooldown process

KPI (KEY PERFORMANCE INDICATORS APPLICATION ON BALLAST WATER TREATMENT SYSTEM SELECTION

Directory of Open Access Journals (Sweden)

Gülçin Vural

2017-01-01

Full Text Available Every day, more than 7,000 different marine species are transferred to different ecosystems via ballast water in ships. The introduction of invasive species can cause problems for native species. After realizing the serious potential problems associated with the transport of organisms in ballast water, national and international regulations were developed. In 2004, the International Maritime Organization introduced the International Convention for the Control and Management of Ships' Ballast Water and Sediments. With these regulations, the problems caused by ballast water have attracted attention and many companies have started to research and develop technologies for the management of ballast water. Today, there are hundreds of different systems for ballast-water treatment, and the selection of the most suitable system for a specific vessel is an increasingly important issue as the Convention nears enforcement on September 8, 2017. The goal of this study is to demonstrate that the application of key performance indicators (KPIs to the selection of a ballast-water treatment system (BWTS leads to a very useful tool with which shipyards can compare BWTSs. This allows them to make better choices and to designate the most suitable system for each of their ships. In this study, we examine two types of vessel from a shipyard in Istanbul, Turkey. They have different ballast-water capacities and equipment, and the most suitable system for each is selected by using the KPI method.

[Selection of indicators for continuous monitoring of the impact of programs optimizing antimicrobial use in Primary Care].

Science.gov (United States)

Fernández-Urrusuno, Rocío; Flores-Dorado, Macarena; Moreno-Campoy, Eva; Montero-Balosa, M Carmen

2015-05-01

To determine core indicators for monitoring quality prescribing in Primary Care based on the evidence, and to assess the feasibility of these indicators for monitoring the use of antibiotics. A literature review was carried out on quality indicators for antimicrobial prescribing through an electronic search limited to the period 2001-2012. It was completed with an "ad hoc" search on the websites of public national and international health services. Finally, indicators were chosen by consensus by a multidisciplinary group of professionals dedicated to managing infections from several areas. The feasibility and applicability of these indicators was verified through the reporting and use of data in the prescription database. Twenty two indicators were found. The consensus group selected 16 indicators. Eleven of them measure the specific antimicrobial selection, and 5 are consumption rates. The indicators were successfully applied to the prescription database, being able to make comparisons between different geographical areas and to observe trends in prescriptions. The definition of a basic set of indicators to monitor antibiotic use adapted to local conditions is required. The results of these indicators can be used for feedback to professionals and for evaluating the impact of programs aimed at improving antimicrobial use. Copyright © 2014 Elsevier España, S.L.U. y Sociedad Española de Enfermedades Infecciosas y Microbiología Clínica. All rights reserved.

A method for managing the storage of fissile materials using criticality indices

International Nuclear Information System (INIS)

Philbin, J.S.; Harms, G.A.

1995-01-01

This paper describes a method for criticality control at fissile material storage facilities. The method involves the use criticiality indices for storage canisters. The logic, methodology, and results for selected canisters are presented. A concept for an interactive computer program using the method is also introduced. The computer program can be used in real time (using precalulated data) to select a Criticality Index (CI) for a container when it is delivered to or packaged at a site. Criticality safety is assured by controlling the sum of the CIs at each storage location below a defined Emit value when containers are moved

Simultaneous improvement of grain yield and protein content in durum wheat by different phenotypic indices and genomic selection.

Science.gov (United States)

Rapp, M; Lein, V; Lacoudre, F; Lafferty, J; Müller, E; Vida, G; Bozhanova, V; Ibraliu, A; Thorwarth, P; Piepho, H P; Leiser, W L; Würschum, T; Longin, C F H

2018-06-01

Simultaneous improvement of protein content and grain yield by index selection is possible but its efficiency largely depends on the weighting of the single traits. The genetic architecture of these indices is similar to that of the primary traits. Grain yield and protein content are of major importance in durum wheat breeding, but their negative correlation has hampered their simultaneous improvement. To account for this in wheat breeding, the grain protein deviation (GPD) and the protein yield were proposed as targets for selection. The aim of this work was to investigate the potential of different indices to simultaneously improve grain yield and protein content in durum wheat and to evaluate their genetic architecture towards genomics-assisted breeding. To this end, we investigated two different durum wheat panels comprising 159 and 189 genotypes, which were tested in multiple field locations across Europe and genotyped by a genotyping-by-sequencing approach. The phenotypic analyses revealed significant genetic variances for all traits and heritabilities of the phenotypic indices that were in a similar range as those of grain yield and protein content. The GPD showed a high and positive correlation with protein content, whereas protein yield was highly and positively correlated with grain yield. Thus, selecting for a high GPD would mainly increase the protein content whereas a selection based on protein yield would mainly improve grain yield, but a combination of both indices allows to balance this selection. The genome-wide association mapping revealed a complex genetic architecture for all traits with most QTL having small effects and being detected only in one germplasm set, thus limiting the potential of marker-assisted selection for trait improvement. By contrast, genome-wide prediction appeared promising but its performance strongly depends on the relatedness between training and prediction sets.

Fusion-reactor blanket-material safety-compatibility studies

International Nuclear Information System (INIS)

Jeppson, D.W.; Muhlestein, L.D.; Keough, R.F.; Cohen, S.

1982-11-01

Blanket material selection for fusion reactors is strongly influenced by the desire to minimize safety and environmental concerns. Blanket material safety compatibility studies are being conducted to identify and characterize blanket-coolant-material interactions under postulated reactor accident conditions. Recently completed scoping compatibility tests indicate that : (1) ternary oxides (LiAlO 2 , Li 2 ZrO 3 , Li 2 SiO 3 , Li 4 SiO 4 and LiTiO 3 ) at postulated blanket operating temperatures are compatible with water coolant, while liquid lithium and Li 7 Pb 2 alloy reactions with water generate heat, aerosol and hydrogen; (2) lithium oxide and Li 17 Pb 83 alloy react mildly with water requiring special precautions to control hydrogen release; (3) liquid lithium reacts substantially, while Li 17 Pb 83 alloy reacts mildly with concrete to produce hydrogen; and (4) liquid lithium-air reactions present some major safety concerns

Development and integration of programmatic performance indicators

International Nuclear Information System (INIS)

Wreathall, J.; Appignani, P.; Modarres, M.

1990-01-01

Work is currently being performed to develop and integrate programmatic performance indicators, that is, indicators of performance associated with the influence on safety associated with plant functional areas like maintenance, operations and training. The process for identifying and evaluating indicators associated with maintenance and training has been described earlier. Since that time, the authors have evaluated the maintenance indicators: inadvertent engineered safety feature actuations due to test and maintenance errors, and daily power loss (DPL), which seemingly show relationships to safety. Work on training process will lead to characteristic sorts of behavior. In the integration study, several frameworks have been developed to provide a basis for describing the interrelationships of plant behavior, personnel behavior, and safety. These will be applied in the next phase of the work to perform the nominal integration

Indicators of health and safety among institutionalized older adults.

Science.gov (United States)

Cavalcante, Maria Lígia Silva Nunes; Borges, Cíntia Lira; Moura, Acácia Maria Figueiredo Torres de Melo; Carvalho, Rhanna Emanuela Fontenele Lima de

2016-01-01

To identify the incidence of mortality, diarrheal diseases, scabies and falls; and the prevalence of pressure ulcers - all of which are related to the safety ofinstitutionalized older adults. This was a documentary retrospective study developed in a long-term residential careinstitution for older adults in the Northeast region of Brazil. The data were gathered from records of health assessment indicators filed between January 2008 and December 2015. Analysis included absolute case frequency; the sum of monthly prevalence and incidence rates; mean values of cases; and mean annual incidence and prevalence rates. The incidence of mortality over these nine years ranged from 9% to 13%; of acute diarrheic disease from 13% to 45%; and scabies from 21% to 63%. The prevalence of pressure ulcers ranged from 8% to 23%. Between 2012 and 2015, the incidence rate of falls without injury varied from 38% to 83%, and with injury from12% to 20%. Analysis of the health indicators revealeda high incidence of scabies and falls and a high prevalence of pressure ulcers. The identification of less than optimal rates for performance indicators canhelp improve the quality of nursing care. Identificar a incidência de mortalidade, doenças diarreicas, escabiose e quedas, e a prevalência de lesões por pressão para a segurança do idoso institucionalizado. Estudo documental, retrospectivo desenvolvido em uma Instituição de Longa Permanência para Idosos, localizada no nordeste do Brasil. Os dados foram coletados por meio dos registros dos indicadores de avaliação de saúde, arquivados de janeiro de 2008 a dezembro de 2015. A análise incluiu a frequência absoluta dos casos; o somatório das taxas de prevalência e incidência mensais; a média de casos e das taxas de incidência e prevalência anuais. Observa-se que a incidência de óbitos nos nove anos considerados variou de 9 a 13%; de doenças diarreicas agudas, de 13 a 45%; e de escabiose, de 21 a 63%. A prevalência de lesão por

The mechanism of selecting priority options and sequence of solutions to ensure the safety of towing caravan navigation

Directory of Open Access Journals (Sweden)

Brazhnyy A. I.

2016-12-01

Full Text Available The paper considers navigational safety movement of the towed object and tugboat. Some methods of alternatives choice of decision-maker persons (DMP to manage the safety of towing a caravan have been presented. Examples of navigation safety conditions, their operational relationship, critical and emergency character with respect to the predetermined position of the band have been given; the sequence of forming actions of the algorithm based on an assessment of possible losses for the sustainability of the towing operation has been proposed. The aim is to research and develop a sequence of logical conclusions for forming some mechanism to take corrective action when navigating the composition of the output of the towing caravan of navigation stable security situation for its return to the original settings of sustainable movement. To assess the risks of navigation functions the risk analysis method has been used, with further selection of management synthesized for towing process, taking into account the possible reaction of the "human element". For estimations well-known in the probability theory and mathematical statistics methods have been used. An iterative mathematical model of the tow caravan considering the posterior distribution of parameters caravan phase coordinates for the given cases has been built. The possibility of resource losses when choosing the optimal alternative has been investigated. It has been established that while selecting and adopting a single decision under risk, including alternatives to the losses, one can always find such an alternative which is able to ensure the management of the caravan navigational safety decreasing the probability of large losses. When operating the navigation state of towing caravan one should choose the optimal alternative that minimizes the possibility of the maximum cost, and then based on it to choose (with incomplete awareness of decision-makers optimal sequence of controls which in turn

Description of data-sources used in SafetyCube, Deliverable 3.1 of the H2020 project SafetyCube (Safety CaUsation, Benefits and Efficiency).

NARCIS (Netherlands)

Hagström, L. Thomson, R. Hermitte, T. Weijermars, W. Bos, N. Talbot, R. Thomas, P. Dupont, E. Martensen, H. Bauer, R. Hours, M. Høye, E. Jänsch, M. Murkovic, A. Niewöhner, W. Papadimitriou, E. Pérez, C. Phan, V. Usami, D. & Vázquez-de-Prada, J.

2017-01-01

Safety CaUsation, Benefits and Efficiency (SafetyCube) is a European Commission supported Horizon 2020 project with the objective of developing an innovative road safety Decision Support System (DSS) that will enable policy-makers and stakeholders to select and implement the most appropriate

Evaluation of indicators for the early selection of the height character in Musa spp.

Directory of Open Access Journals (Sweden)

Lourdes García Rodríguez

2004-10-01

Full Text Available In the plant breeding programs attended by Biotechnology and using the induction of mutations becomes necessary to work with big populations of plants to guarantee bigger possibilities to be successful in the work. For what to have a selection system that allows to carry out the same one in acclimatization phase would allow to shorten the outlines of improvement and to diminish the population’s size notably to evaluate in field phase, what would bear to diminish the expenses in the whole process of studies clones them. With the aim of determining possible morphological indicators that could be used as markers for the selection of low bearing in the clones of the FHIA were studied in conditions of acclimatization different cultivars and banana mutants, being evaluated several morphological characters as: the height of the plant, number of leaves, long and wide of the penultimate emitted leaf, as well as the long of their petiole and the distance between two serial leaves. It was also evaluated the height of the plants under conditions in vitro when they were subcultivate in a culture medium with different concentration of AG3. The results indicate that inside the evaluated morphological characters, those that more early allowed to distinguish among plants of low bearing were: the long of the petiole and the height of the plants and that the moment of the selection should be to the 60 days. Not differences were observed between genotypes when they were subcultivate in the culture medium enriched with AG3. Key words: banana, early selection, low bearing, morphological markers, plantain

Why Include Impacts on Biodiversity from Land Use in LCIA and How to Select Useful Indicators?

Directory of Open Access Journals (Sweden)

Ottar Michelsen

2015-05-01

Full Text Available Loss of biodiversity is one of the most severe threats to sustainability, and land use and land use changes are still the single most important factor. Still, there is no sign of any consensus on how to include impacts on biodiversity from land use and land use changes in LCIA. In this paper, different characteristics of biodiversity are discussed and related to proposals on how to include land use and land use changes in LCIA. We identify the question of why we should care about biodiversity as a key question, since different motivations will result in different choices for the indicators, and we call for more openness in the motivation for indicator selection. We find a promising trend in combining pressure indicators with geographic weighting and regard this as a promising way ahead. More knowledge on the consequences of different choices, such as the selection of a reference state, is still needed.

Benchmarking Global Food Safety Performances: The Era of Risk Intelligence.

Science.gov (United States)

Valleé, Jean-Charles Le; Charlebois, Sylvain

2015-10-01

Food safety data segmentation and limitations hamper the world's ability to select, build up, monitor, and evaluate food safety performance. Currently, there is no metric that captures the entire food safety system, and performance data are not collected strategically on a global scale. Therefore, food safety benchmarking is essential not only to help monitor ongoing performance but also to inform continued food safety system design, adoption, and implementation toward more efficient and effective food safety preparedness, responsiveness, and accountability. This comparative study identifies and evaluates common elements among global food safety systems. It provides an overall world ranking of food safety performance for 17 Organisation for Economic Co-Operation and Development (OECD) countries, illustrated by 10 indicators organized across three food safety risk governance domains: risk assessment (chemical risks, microbial risks, and national reporting on food consumption), risk management (national food safety capacities, food recalls, food traceability, and radionuclides standards), and risk communication (allergenic risks, labeling, and public trust). Results show all countries have very high food safety standards, but Canada and Ireland, followed by France, earned excellent grades relative to their peers. However, any subsequent global ranking study should consider the development of survey instruments to gather adequate and comparable national evidence on food safety.

Detecting adverse events in surgery: comparing events detected by the Veterans Health Administration Surgical Quality Improvement Program and the Patient Safety Indicators.

Science.gov (United States)

Mull, Hillary J; Borzecki, Ann M; Loveland, Susan; Hickson, Kathleen; Chen, Qi; MacDonald, Sally; Shin, Marlena H; Cevasco, Marisa; Itani, Kamal M F; Rosen, Amy K

2014-04-01

The Patient Safety Indicators (PSIs) use administrative data to screen for select adverse events (AEs). In this study, VA Surgical Quality Improvement Program (VASQIP) chart review data were used as the gold standard to measure the criterion validity of 5 surgical PSIs. Independent chart review was also used to determine reasons for PSI errors. The sensitivity, specificity, and positive predictive value of PSI software version 4.1a were calculated among Veterans Health Administration hospitalizations (2003-2007) reviewed by VASQIP (n = 268,771). Nurses re-reviewed a sample of hospitalizations for which PSI and VASQIP AE detection disagreed. Sensitivities ranged from 31% to 68%, specificities from 99.1% to 99.8%, and positive predictive values from 31% to 72%. Reviewers found that coding errors accounted for some PSI-VASQIP disagreement; some disagreement was also the result of differences in AE definitions. These results suggest that the PSIs have moderate criterion validity; however, some surgical PSIs detect different AEs than VASQIP. Future research should explore using both methods to evaluate surgical quality. Published by Elsevier Inc.

Inland Waterway Environmental Safety

Science.gov (United States)

Reshnyak, Valery; Sokolov, Sergey; Nyrkov, Anatoliy; Budnik, Vlad

2018-05-01

The article presents the results of development of the main components of the environmental safety when operating vessels on inland waterways, which include strategy selection ensuring the environmental safety of vessels, the selection and justification of a complex of environmental technical means, activities to ensure operation of vessels taking into account the environmental technical means. Measures to ensure environmental safety are developed on the basis of the principles aimed at ensuring environmental safety of vessels. They include the development of strategies for the use of environmental protection equipment, which are determined by the conditions for wastewater treatment of purified sewage and oily bilge water as well as technical characteristics of the vessels, the introduction of the process of the out-of-the-vessel processing of ship pollution as a technology for their movement. This must take into account the operating conditions of vessels on different sections of waterways. An algorithm of actions aimed at ensuring ecological safety of operated vessels is proposed.