Transportation of hazardous and nuclear materials

International Nuclear Information System (INIS)

Boryczka, M.; Shaver, D.

1989-01-01

Transportation of hazardous and radioactive materials is a vital part of the nation's economy. In recent years public concern over the relative safety of transporting hazardous materials has risen sharply. The United States has a long history of transporting hazardous and radioactive material; rocket propellants, commercial spent fuel, low-level and high-level radioactive waste has been shipped for years. While the track record for shipping these materials is excellent, the knowledge that hazardous materials are passing through communities raises the ire of citizens and local governments. Public outcry over shipments containing hazardous cargo has been especially prominent when shippers have attempted to transport rocket propellants or spent nuclear fuel. Studies of recent shipments have provided insight into the difficulties of shipping in a politically charged environment, the major issues of concern to citizens, and some of the more successful methods of dealing with public concerns. This paper focuses on lessons learned from these studies which include interviews with shippers, carriers, and regulators

Hazardous material reduction initiative

International Nuclear Information System (INIS)

Nichols, D.H.

1995-02-01

The Hazardous Material Reduction Initiative (HMRI) explores using the review of purchase requisitions to reduce both the use of hazardous materials and the generation of regulated and nonregulated wastes. Based on an 11-month program implemented at the Hanford Site, hazardous material use and waste generation was effectively reduced by using a centralized procurement control program known as HMRI. As expected, several changes to the original proposal were needed during the development/testing phase of the program to accommodate changing and actual conditions found at the Hanford Site. The current method requires a central receiving point within the Procurement Organization to review all purchase requisitions for potentially Occupational Safety and Health Administration (OSHA) hazardous products. Those requisitions (approximately 4% to 6% of the total) are then forwarded to Pollution Prevention personnel for evaluation under HMRI. The first step is to determine if the requested item can be filled by existing or surplus material. The requisitions that cannot filled by existing or surplus material are then sorted into two groups based on applicability to the HMRI project. For example, laboratory requests for analytical reagents or standards are excluded and the purchase requisitions are returned to Procurement for normal processing because, although regulated, there is little opportunity for source reduction due to the strict protocols followed. Each item is then checked to determine if it is regulated or not. Regulated items are prioritized based on hazardous contents, quantity requested, and end use. Copies of these requisitions are made and the originals are returned to Procurement within 1-hr. Since changes to the requisition can be made at later stages during procurement, the HMRI fulfills one of its original premises in that it does not slow the procurement process

46 CFR 151.03-30 - Hazardous material.

Science.gov (United States)

2010-10-01

... hazardous material means a liquid material or substance that is— (a) Flammable or combustible; (b) Designated a hazardous substance under section 311(b) of the Federal Water Pollution Control Act (33 U.S.C... Agency designates hazardous substances in 40 CFR Table 116.4A. The Coast Guard designates hazardous...

The transport of hazardous materials

International Nuclear Information System (INIS)

Goemmel, F.

1987-01-01

The rapid development of all kinds of transports has been leading to a continuously increasing number of accidents involving the release and escape of hazardous materials. The risks involved for men and the environment have to be realized and reduced to a minimum. Efforts in this field have meanwhile been accumulating an enormous quantity of rules, recommendations and regulations. They comprise, among others, both national and international rail transport, maritime transport, inland shipping, air and road transport regulations adding up to a total of about 5000 pages. The publication discusses the necessity and justification of the existing quantity of regulations, it deals with their possible simplification and modified user-oriented arrangement as well as with a possible international harmonization of regulations. Apart from giving a general survey of the transport of hazardous materials the author reviews the intensive efforts which are going into the safety of the transport of hazardous materials and points out technical and legal problems which have remained unsolved so far. The publication essentially contributes to clearing up the background, perspectives and prospects of the complex regulations controlling the transport of hazardous materials. (orig./HP) [de

78 FR 69745 - Safety and Security Plans for Class 3 Hazardous Materials Transported by Rail

Science.gov (United States)

2013-11-20

... material (considering the material's underlying chemical properties, corrosivity, and other characteristics) is fundamental to ensuring the selection of proper packaging and that the hazards of the materials...

75 FR 17111 - Hazardous Materials Regulations: Combustible Liquids

Science.gov (United States)

2010-04-05

... the probability and quantity of a hazardous material release. Under the HMR, hazardous materials are... present during transportation. The HMR specify appropriate packaging and handling requirements for... hazardous materials in commerce. During our regulatory review process, we look for opportunities that may...

Hazardous materials routing - risk management of mismanagement

International Nuclear Information System (INIS)

Glickman, T.S.

1988-01-01

Along with emergency planning and preparedness, the placement of restrictions on routing has become an increasingly popular device for managing the highway and rail risks of hazardous materials transportation. Federal studies conducted in 1985 indicate that at that time there were 513 different state and local restrictions on the routing of hazardous materials for these two modes of transportation, and that there were 136 state and local notification requirements, that is, restrictions that take the form of a statute or ordinance requiring advance warning or periodic reporting about hazardous materials shipments. Routing restrictions also take the form of prohibiting the use of road, a tunnel, or a bridge for a specified set of hazardous materials

76 FR 51324 - Hazardous Materials: Incorporating Rail Special Permits Into the Hazardous Materials Regulations

Science.gov (United States)

2011-08-18

... through use of electronic data interchange (EDI). The IVOHMA states ``differences in hazard communication... and on the possible effects EDI may have on distributing hazardous materials shipping paper... consider the use of EDI in other modes of transport in a future rulemaking. Petition No. P-1567 PHMSA...

A comprehensive approach to managing hazardous materials

International Nuclear Information System (INIS)

Donovan, A.

1990-01-01

An increased emphasis on the need for environmental protection indicates that engineers must now consider the disposition of unused hazardous materials as waste. Before specifying and ordering materials, the engineer must consider the impact of the Resource Conservation and Recovery Act (RCRA) and the Occupational Safety and Health Administration's (OSHA's) Hazard Communication Standard. Many commonly used materials such as paint, solvents, glues, and sealants fall under the requirements of these regulations. This paper presents a plant to manage hazardous materials at the US Department of Energy's (DOE's) Waste Isolation Pilot Plant (WIPP), which is managed and operated by Westinghouse Electric Corporation. The basic elements of the plan are training, hazard communication, storage and handling, tracking, and disposal. Steps to be taken to develop the plan are outlined, problems and successes are addressed, and interactions among all affected departments are identified. The benefits of an organized and comprehensive approach to managing hazardous materials are decreased worker injuries, reduction of accidental releases, minimization of waste, and compliance with federal, state, and local safety and environmental laws. In summary, the benefits of an organized program for the management of hazardous materials include compliance with the Environmental Protection Agency's (EPA's) requirements, demonstration of Westinghouse's role as a responsible corporate entity, and reduction of waste management costs

30 CFR 56.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 56.16004 Section 56.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16004 Containers for hazardous materials. Containers holding hazardous materials...

30 CFR 57.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 57.16004 Section 57.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16004 Containers for hazardous materials. Containers holding hazardous materials...

Hazardous materials and waste management a guide for the professional hazards manager

CERN Document Server

Cheremisinoff, Nicholas P

1995-01-01

The management of hazardous materials and industrial wastes is complex, requiring a high degree of knowledge over very broad technical and legal subject areas. Hazardous wastes and materials are diverse, with compositions and properties that not only vary significantly between industries, but within industries, and indeed within the complexity of single facilities. Proper management not only requires an understanding of the numerous and complex regulations governing hazardous materials and waste streams, but an understanding and knowledge of the treatment, post-treatment, and waste minimizatio

Health and safety information program for hazardous materials

International Nuclear Information System (INIS)

O'Brien, M.P.; Fallon, N.J.; Kuehner, A.V.

1979-01-01

The system is used as a management tool in several safety and health programs. It is used to: trace the use of hazardous materials and to determine monitoring needs; inform the occupational physician of the potential health problems associated with materials ordered by a given individual; inform the fire and rescue group of hazardous materials in a given building; provide waste disposal recommendations to the hazardous waste management group; assist the hazardous materials shipping coordinator in identifying materials which are regulated by the Department of Transportation; and guide management decisions in the area of recognizing and rectifying unsafe conditions. The information system has been expanded from a manual effort to provide a brief description of health hazards of chemicals used at the lab to a computerized health and safety information system which serves the needs of all personnel who may encounter the material in the course of their work. The system has been designed to provide information needed to control the potential problems associated with a hazardous material up to the time that it is consumed in a given operation or is sent to the waste disposal facility

78 FR 24309 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2013-04-24

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration List of Special Permit Applications Delayed AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA..., Pipeline and Hazardous Materials Safety Administration, U.S. Department of Transportation, East Building...

76 FR 45332 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-07-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: List of Applications for Modification of..., 2011. ADDRESSES: Record Center, Pipeline and Hazardous Materials Safety Administration, U.S. Department...

Transportation of hazardous materials (hazmat) a literature survey

OpenAIRE

Zafer YILMAZ; Serpil EROL; Hakan Soner APLAK

2016-01-01

ransportation has a great role in logistics. Many researchers have studied on transportation and vehicle routing problems. Transportation of hazardous materials (hazmat) is a special subject for logistics. Causalities due to the accidents caused by trucks carrying hazardous materials will be intolerable. Many researchers have studied on risk assessment of hazmat transportation to find ways for reducing hazardous material transportation risks. Some researchers have studied routing of hazmat tr...

US Hazardous Materials Routes, Geographic WGS84, BTS (2006) [hazardous_material_routes_BTS_2006

Data.gov (United States)

Louisiana Geographic Information Center — The Federal Motor Carrier Safety Administration (FMCSA) Hazardous Material Routes were developed using the 2004 First Edition TIGER/Line files. The routes are...

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1992-01-01

The hazardous materials (hazmat) packaging development and certification process is currently defined by two different regulatory philosophies, one based on specification packagings and the other based on performance standards. With specification packagings, a packaging is constructed according to an agreed set of design specifications. In contrast, performance standards do not specify the packaging design; they specify performance standards that a packaging design must be able to pass before it can be certified for transport. The packaging can be designed according to individual needs as long as it meets these performance standards. Performance standards have been used nationally and internationally for about 40 years to certify radioactive materials (RAM) packagings. It is reasonable to state that for RAM transport, performance specifications have maintained transport safety. A committee of United Nation's experts recommended the performance standard philosophy as the preferred regulation method for hazmat packaging. Performance standards for hazmat packagings smaller than 118 gallons have been adopted in 49CFR178. Packagings for materials that are classified as toxic-by-inhalation must comply with the performance standards by October 1, 1993, and packagings for all other classes of hazardous materials covered must comply by October 1, 1996. For packages containing bulk (in excess of 188 gallons) quantities of materials that are extremely toxic by inhalation, there currently are no performance requirements. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project to look at the subset of bulk packagings that are larger than 2000 gallons. The objectives of this project are the evaluate current hazmat specification packagings and develop supporting documentation for determining performance requirements for packagings in excess of 2000 gallons that transport hazardous materials that have been classified as extremely toxic by inhalation (METBI)

Sustainable Materials Management: Non-Hazardous Materials and Waste Management Hierarchy

Science.gov (United States)

EPA developed the non-hazardous materials and waste management hierarchy in recognition that no single waste management approach is suitable for managing all materials and waste streams in all circumstances.

Technology assessment of solar-energy systems. Materials resource and hazardous materials impacts of solar deployment

Science.gov (United States)

Schiffman, Y. M.; Tahami, J. E.

1982-04-01

The materials-resource and hazardous-materials impacts were determined by examining the type and quantity of materials used in the manufacture, construction, installation, operation and maintenance of solar systems. The materials requirements were compared with US materials supply and demand data to determine if potential problems exist in terms of future availability of domestic supply and increased dependence on foreign sources of supply. Hazardous materials were evaluated in terms of public and occupational health hazards and explosive and fire hazards. It is concluded that: although large amounts of materials would be required, the US had sufficient industrial capacity to produce those materials; (2) postulated growth in solar technology deployment during the period 1995-2000 could cause some production shortfalls in the steel and copper industry; the U.S. could increase its import reliance for certain materials such as silver, iron ore, and copper; however, shifts to other materials such as aluminum and polyvinylchloride could alleviate some of these problems.

An optimization model for transportation of hazardous materials

International Nuclear Information System (INIS)

Seyed-Hosseini, M.; Kheirkhah, A. S.

2005-01-01

In this paper, the optimal routing problem for transportation of hazardous materials is studied. Routing for the purpose of reducing the risk of transportation of hazardous materials has been studied and formulated by many researcher and several routing models have been presented up to now. These models can be classified into the categories: the models for routing a single movement and the models for routing multiple movements. In this paper, according to the current rules and regulations of road transportations of hazardous materials in Iran, a routing problem is designed. In this problem, the routs for several independent movements are simultaneously determined. To examine the model, the problem the transportations of two different dangerous materials in the road network of Mazandaran province in the north of Iran is formulated and solved by applying Integer programming model

Project management plan, Hazardous Materials Management and Emergency Response Training Center

International Nuclear Information System (INIS)

Borgeson, M.E.

1994-01-01

For the next 30 years, the main activities at the Hanford Site will involve the handling and cleanup of toxic substances. Thousands of workers involved in these new activities will need systematic training appropriate to their tasks and associated risks. This project is an important part of the Hanford Site mission and will enable the US Department of Energy (DOE) to meet high standards for safety. The Hazardous Materials Management and Emergency Response Training Center (HAMMER) project will construct a centralized regional training center dedicated to training hazardous materials workers and emergency responders in classrooms and with hands-on, realistic training aids representing actual field conditions. The HAMMER Training Center will provide a cost-effective, high-quality way to meet the Hanford Site training needs. The training center creates a partnership among DOE; government contractors; labor; local, state, and tribal governments; and selected institutions of higher education

Investigating the presence of hazardous materials in buildings

International Nuclear Information System (INIS)

Gustitus, D.A.; Blaisdell, P.M.

1996-01-01

Environmental hazards in buildings can be found in the air, on exposed surfaces, or hidden in roofs, walls, and systems. They can exist in buildings in solid, liquid, and gaseous states. A sound methodology for investigating the presence of environmental hazards in buildings should include several components. The first step in planning an investigation of environmental hazards in buildings is to ascertain why the investigation is to be performed. Research should be performed to review available documentation on the building. Next, a visual inspection of the building should be performed to identify and document existing conditions, and all suspect materials containing environmental hazards. Lastly, samples of suspect materials should be collected for testing. It is important to sample appropriate materials, based on the information obtained during the previous steps of the investigation. It is also important to collect the samples using standard procedures. Pollutants of concern include asbestos, lead, PCBs, and radon

Hazardous-materials-management system: a guide for local emergency managers

International Nuclear Information System (INIS)

Lee, M.T.; Roe, P.G.

1981-07-01

An increase in the manufacture, storage, and transportation of hazardous materials is occurring across the nation. Local jurisdictions have realized that they have the responsibility to assure a reasonable level of safety to their community members and visitors alike. Such a responsibility can be met by developing methods of preventing hazardous materials incidents; enforcing laws related to transporting and storing hazardous materials; the initiating of an appropriate first response, and activating available resources of government agencies and commercial organizations that deal with containment and cleanup. This manual has been written to help in the development of a total Hazardous Material Management System. The manual describes one approach but allows for variations as may be appropriate for the specific jurisdiction

49 CFR 173.33 - Hazardous materials in cargo tank motor vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hazardous materials in cargo tank motor vehicles... Transportation § 173.33 Hazardous materials in cargo tank motor vehicles. (a) General requirements. (1) No person may offer or accept a hazardous material for transportation in a cargo tank motor vehicle except as...

Preventing method and device for underground permeation of hazardous material

International Nuclear Information System (INIS)

Funabashi, Kiyomi; Kurokawa, Hideaki; Fukazawa, Tetsuo; Yamazaki, Tadashi.

1996-01-01

In a method of preventing hazardous materials from permeating into ground by burying adsorbing materials underground, a plurality of adsorbing layers are laminated being spaced apart from each other, the concentration of the hazardous materials between each of the adsorbent layers is measured. When the concentration reaches a predetermined value, the adsorbent layers are regenerated. A suppression means for preventing hazardous materials from permeating into the ground are formed by an upper adsorbent layer and a lower adsorbent layer, and a means for measuring the concentration of hazardous materials passing through the upper adsorbent layer and a means for charging and discharging regenerated liquid are disposed. When it is detected that the poisonous materials can not be eliminated, the poisonous materials are already permeated to the adsorbent layer, and they start to inflow into underground water. In order to prevent it, an adsorbent layer is additionally disposed at the lower side of the place of detection to eliminate the poisonous materials completely thereby enabling to prevent poisonous materials from permeating into underground for a long period of time. (T.M.)

Double-pulse standoff laser-induced breakdown spectroscopy for versatile hazardous materials detection

Energy Technology Data Exchange (ETDEWEB)

Gottfried, Jennifer L. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)], E-mail: jennifer.gottfried@arl.army.mil; De Lucia, Frank C.; Munson, Chase A.; Miziolek, Andrzej W. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)

2007-12-15

We have developed a double-pulse standoff laser-induced breakdown spectroscopy (ST-LIBS) system capable of detecting a variety of hazardous materials at tens of meters. The use of a double-pulse laser improves the sensitivity and selectivity of ST-LIBS, especially for the detection of energetic materials. In addition to various metallic and plastic materials, the system has been used to detect bulk explosives RDX and Composition-B, explosive residues, biological species such as the anthrax surrogate Bacillus subtilis, and chemical warfare simulants at 20 m. We have also demonstrated the discrimination of explosive residues from various interferents on an aluminum substrate.

Instrumentation for Detecting Hazardous Materials.

Science.gov (United States)

1980-06-01

equipment a detector for monitoring radioactivity . A portable device for detecting the presence of hazardous mate- rials should also be included in the...Acrylonitrile 2 Natural Gas/LNG 2 211 ----- Material Name (Cont’d.) Number of Times Listed Radioactive Materials 2 Fertilizers 1 Cellulose Nitrate 1 Acrolein...Birnbaum, and Curtis Fincher, L "Fluorescence Determination of the Atmospheric Polutant NO2 in Impact of Lasers in Spectroscopy, Vol. 49 of Proceed

Two Chaotic Patterns of Dynamic Risk Definition for Solving Hazardous Materials Routing Problem

Directory of Open Access Journals (Sweden)

Abbas Mahmoudabadi

2015-01-01

Full Text Available In the case of determining routes for hazardous material transportation, risk is considered as a main attribute. Transport risk, which is usually combined with other attributes such as cost or travel time, plays a significant role in determining paths for hazardous materials transportation. Since, risk is chaotically affected by road incidents, decision makers are dealing with selecting a method for defining chaotic risk factors in hazmat transportation. In this paper, transport risk has been defined as a chaotic variable using two different methods of generating chaotic patterns. In an experimental road network, which consists of eighty-nine nodes and one hundred and one two-way links, two different methods of generating chaotic variables have been used for applying the proposed procedure. In addition, results for different amounts of risk and cost have also been analyzed in case study. Results revealed that different cost and risk priorities change the frequencies of selected paths determined for hazmat transportation, but the route convergence of the route to chaos method is better than that of the logistic map equation.

Transportation of hazardous materials (hazmat a literature survey

Directory of Open Access Journals (Sweden)

Zafer YILMAZ

2016-02-01

Full Text Available ransportation has a great role in logistics. Many researchers have studied on transportation and vehicle routing problems. Transportation of hazardous materials (hazmat is a special subject for logistics. Causalities due to the accidents caused by trucks carrying hazardous materials will be intolerable. Many researchers have studied on risk assessment of hazmat transportation to find ways for reducing hazardous material transportation risks. Some researchers have studied routing of hazmat trucks. The emergency response models and network design problems for hazmat transportation were also studied by some researchers. The transportation of hazmats can also be classified according to the mode of transport. Mainly roads are used for hazmat transportation but some shipments are intermodal. There has been a great amount of effort spent to find convenient ways for hazmat transportation. In this study, a literature survey for the articles about hazmat transportation is prepared. After pointing out the importance of hazmat transportation by the example of US hazmat transportation data, the studies on hazmat transportation since 2005 have been examined. Totally 88 articles are classified as risk, routing, routing and scheduling, emergency response, network design and accident analysis. What can be studied in future researches is pointed out.Keywords: Hazardous materials, Network design, Transportation, Routing, Risk assessment

Auditors of safety in hazardous materials transportation

International Nuclear Information System (INIS)

Manas Lahoz, J.L.

1993-01-01

The author describes the methodology for safety auditory and control, prevention, risks of hazardous materials transport through ship, airplane, rail, etc. In this way, The author presents the classification of damage materials transport, characteristic damage and different transport methods

Risk methodologies for offsite hazardous materials

International Nuclear Information System (INIS)

Kot, C.A.; Eichler, T.V.; Wiedermann, A.H.

1983-01-01

A number of suggestions have been advanced in recent years concerning the risks posed to nuclear power plants by offsite hazardous materials relative to (1) the regulatory approach including considerations of minimum and safe standoff distances, exclusion distances, site acceptance ceilings and floors, screening distances and screening probabilities, plant design, etc., and (2) the analysis and evaluation procedures such as material screening criteria, plant vulnerability, standarized physical models, etc. An evaluation of current analyses and approaches indicates that this complex problem, variety of approaches, and safety concerns may be better accommodated by developing criteria and treatments along the lines of a so-called conditional risk approach. Specifically, the probability (P) of some ultimate consequence (C) occurring from an accident (A) involving hazardous materials is given as P(C) = P(C/A) x P(A). Assuming that the plant to accident site standoff distance is the fundamental independent variable of the risk methodology, certain conditional risk designations and conditions can be made and are presented

Regulatory Requirements to Combat Illicit Trafficking of Hazardous Materials

International Nuclear Information System (INIS)

Hussein, A.Z.; Zakaria, Kh.M.

2011-01-01

Since more than a decade illicit Trafficking of hazardous ( CBRNE), materials ( chemical, biological, radiological, nuclear and explosive ) has been identified as a key threat in national, regional, inter regional and international strategies. An Effective response to hazardous materials (CBRNE) risk and threat were realized to require a very high level of cooperation and coordination between various governments and their responsible organizations and authorities of regional and international partner. While improper policy of actions may easily be exploited by non- state members to (CBRNE) trafficking which may lead to develop weapon of mass destruction (WMD). Such strategy are of paramount important between all levels of the states and among regional agreements through comprehensive tailored assistance packages (e.g. export control, illicit trafficking of hazardous materials, redirection of scientist, emergency planning, crisis response safety and security culture. Capacity building, action plans and instruments for stability are necessary actions for efficient combating against illicit trafficking of hazardous materials. Regarding the needs of assessment phase, assistance must be based on data collection, analysis and prioritization of implanting the regulatory controls. Several activities have to be conducted to reduce CBRNE threat. The one- by- one approach, covering either nuclear and radioactive or chemical or biological materials has to be implanted on the country basis performance to mitigate CBRNE hazardous risk. On several consequent phases of intervention dealing with CBRNE risk mitigation the country has to establish a network of local, regional and international capabilities. Such network is setting up the mechanism for the country needs identifications, the guidelines for data collection, for data platform maintenance and update, the data assessment and the competent and operative organizations. This network will be to strengthen the long - term

Tools for Material Design and Selection

Science.gov (United States)

Wehage, Kristopher

-dimensional microstructures are generated by Random Sequential Adsorption (RSA) of voxelized ellipses representing the coarse grain phase. A simulated annealing algorithm is used to geometrically optimize the placement of the ellipses in the model to achieve varying user-defined configurations of spatial arrangement of the coarse grains. During the simulated annealing process, the ellipses are allowed to overlap up to a specified threshold, allowing triple junctions to form in the model. Once the simulated annealing process is complete, the remaining space is populated by smaller ellipses representing the ultra-fine grain phase. Uniform random orientations are assigned to the grains. The program generates text files that can be imported in to Crystal Plasticity Finite Element Analysis Software for stress analysis. Finally, numerical methods and programming are applied to current issues in green engineering and hazard assessment. To understand hazards associated with materials and select safer alternatives, engineers and designers need access to up-to-date hazard information. However, hazard information comes from many disparate sources and aggregating, interpreting and taking action on the wealth of data is not trivial. In light of these challenges, a Framework for Automated Hazard Assessment based on the GreenScreen list translator is presented. The framework consists of a computer program that automatically extracts data from the GHS-Japan hazard database, loads the data into a machine-readable JSON format, transforms the JSON document in to a GreenScreen JSON document using the GreenScreen List Translator v1.2 and performs GreenScreen Benchmark scoring on the material. The GreenScreen JSON documents are then uploaded to a document storage system to allow human operators to search for, modify or add additional hazard information via a web interface.

77 FR 60935 - Hazardous Materials: Minor Editorial Corrections and Clarifications (RRR)

Science.gov (United States)

2012-10-05

... flammable cryogenic liquid is not received by the consignee within 20 days from the date of shipment.... * * * * * Container ship * * * * * * * * Hazardous material means a substance or material that the Secretary of... transportation law (49 U.S.C. 5103). The term includes hazardous substances, hazardous wastes, marine pollutants...

Emergency preparedness hazards assessment for selected 100 Area Bechtel Hanford, Inc. facilities

International Nuclear Information System (INIS)

1997-07-01

The emergency preparedness hazards assessment for Bechtel Hanford Inc. (BHI) facilities in the 100 Areas of the Hanford Site. The purpose of a hazards assessment is to identify the hazardous material at each facility, identify the conditions that could release the hazardous material, and calculate the consequences of the releases. The hazards assessment is the technical basis for the facility emergency plans and procedures. There are many other buildings and past- practice burial grounds, trenches, cribs, etc., in the 100 Areas that may contain hazardous materials. Undisturbed buried waste sites that are not near the Columbia River are outside the scope of emergency preparedness hazards assessments because there is no mechanism for acute release to the air or ground water. The sites near the Columbia River are considered in a separate flood hazards assessment. This hazards assessment includes only the near-term soil remediation projects that involve intrusive activities

Quality assurance for packaging of radioactive and hazardous materials

International Nuclear Information System (INIS)

Gustafson, L.D.

1986-01-01

The Department of Energy (DOE) has required for many years that quality assurance programs be established and implemented for the packaging of radioactive and hazardous materials. This paper identifies various requirement principles and related actions involved in establishing effective quality assurance for packaging of radioactive and hazardous materials. A primary purpose of these quality assurance program activities is to provide assurance that the packaging and transportation of hazardous materials, which includes radioactive and fissile materials, are in conformance with appropriate governmental regulations. Applicable regulations include those issued by the Nuclear Regulatory Commission (NRC), the Department of Transportation (DOT), and the Environmental Protection Agency (EPA). DOE Order 5700.6A establishes that quality assurance requirements are to be applied in accordance with national consensus standards where suitable ones are available. In the nuclear area, ANSI/ASME NQA-1 is the preferred standard

78 FR 60755 - Hazardous Materials: Enhanced Enforcement Procedures-Resumption of Transportation

Science.gov (United States)

2013-10-02

... material,'' we envisioned etiological agents, such as biological products, infectious substances, medical... accidents or incidents involving the transportation of hazardous material. In order to achieve a uniform... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part...

Program in change: shipment of hazardous materials at the INEL

International Nuclear Information System (INIS)

Reed, L.L.

1984-01-01

Positive measures such as education, control, and auditing ability should be incorporated into each hazardous material shipping program to assure compliance with regulations and the safe movement of hazardous materials. This paper discusses these and other pertinent components of a shipping program. 3 references

Environmentally sound management of hazardous waste and hazardous recyclable materials

International Nuclear Information System (INIS)

Smyth, T.

2002-01-01

Environmentally sound management or ESM has been defined under the Basel Convention as 'taking all practicable steps to ensure that hazardous wastes and other wastes are managed in a manner which will protect human health and the environment against the adverse effects which may result from such wastes'. An initiative is underway to develop and implement a Canadian Environmentally Sound Management (ESM) regime for both hazardous wastes and hazardous recyclable materials. This ESM regime aims to assure equivalent minimum environmental protection across Canada while respecting regional differences. Cooperation and coordination between the federal government, provinces and territories is essential to the development and implementation of ESM systems since waste management is a shared jurisdiction in Canada. Federally, CEPA 1999 provides an opportunity to improve Environment Canada's ability to ensure that all exports and imports are managed in an environmentally sound manner. CEPA 1999 enabled Environment Canada to establish criteria for environmentally sound management (ESM) that can be applied by importers and exporters in seeking to ensure that wastes and recyclable materials they import or export will be treated in an environmentally sound manner. The ESM regime would include the development of ESM principles, criteria and guidelines relevant to Canada and a procedure for evaluating ESM. It would be developed in full consultation with stakeholders. The timeline for the development and implementation of the ESM regime is anticipated by about 2006. (author)

Natural radioactivity in some building materials and assessment of the associated radiation hazards

Energy Technology Data Exchange (ETDEWEB)

Kasumovic, Amira; Hankic, Ema; Kasic, Amela; Adrovic, Feriz [Tuzla Univ. (Bosnia and Herzegovina). Dept. of Physics

2018-04-01

The results of the specific activities of {sup 232}Th, {sup 226}Ra and {sup 40}K measured in samples of commonly used building materials in Bosnia and Herzegovina are presented. Measurements were performed by gamma-ray spectrometer with coaxial HPGe detector. The surface radon exhalation and mass exhalation rates for selected building materials were also measured. The determined values of specific activities were in range from 3.16 ± 0.81 Bq kg{sup -1} to 64.79 ± 6.16 Bq kg{sup -1} for {sup 232}Th, from 2.46 ± 0.95 Bq kg{sup -1} to 53.89 ± 3.67 Bq kg{sup -1} for {sup 226}Ra and from 28.44 ± 7.28 Bq kg{sup -1} to 557.30 ± 93.38 Bq kg{sup -1} for {sup 40}K. The radium equivalent activity, the activity concentration index, the external and internal hazard indices as well as the absorbed dose rate in indoor air and the corresponding annual effective dose, due to gamma-ray emission from the radioactive nuclides in the building material, were evaluated in order to assess the radiation hazards for people. The measured specific activities of the natural radioactive nuclides in all investigated building materials were compared with the published results for building materials from other European countries. It can be noted that the results from this study are similar to the data for building materials from neighbouring countries and for building materials used in the EU Member States. The radiological hazard parameters of the building materials were all within the recommended limits for safety use.

Natural radioactivity and radiological hazards of building materials in Xianyang, China

International Nuclear Information System (INIS)

Lu Xinwei; Yang Guang; Ren Chunhui

2012-01-01

Common building materials collected from Xianyang, China were analyzed for the natural radioactivity of 226 Ra, 232 Th and 40 K using γ-ray spectroscopy. The average activity concentration of 226 Ra, 232 Th and 40 K in the studied building materials ranges from 13.4 to 69.9, 13.1–99.1 and 124.7–915.1 Bq kg −1 , respectively. The measured activity concentrations for these radionuclides were compared with the reported data of other countries and with the worldwide average activity of soil. To assess the radiation hazard of the natural radioactivity in all samples to the people, the radium equivalent activity, external hazard index, internal hazard index, indoor absorbed dose rate and total annual effective dose were estimated. The radium equivalent activities of the studied samples are below the internationally accepted values. The external hazard index and internal hazard index of all analyzed building materials are less than unity. The mean values of indoor absorbed dose rate for all building materials except for lime are higher than the world population-weighted average of 84 nGy h −1 and the total annual effective dose values of building materials are lower than 1 mSv y −1 except for some cyan brick samples. The study shows the measured building materials do not pose significant source of radiation hazard and are safe for use in the construction of dwellings. - Highlights: ► Natural radioactivity in building materials was determined by gamma ray spectrometry. ► The radiological hazard of studied building materials is within the recommended safety limit. ► Most of the studied building materials do not pose significant radiation risk to residents.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

Science.gov (United States)

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Unify a hazardous materials/waste program

International Nuclear Information System (INIS)

Carson, H.T.

1988-01-01

Efficiently managing a hazardous materials/waste program in a multi-facility, multi-product corporation is a major challenge. This paper describes several methods to help unify a program and gain maximum efficiency of manpower and to minimize risk

Assessment of Heat Hazard during the Polymerization of Selected Light-Sensitive Dental Materials

OpenAIRE

Janeczek, Maciej; Herman, Katarzyna; Fita, Katarzyna; Dudek, Krzysztof; Kowalczyk-Zaj?c, Ma?gorzata; Czajczy?ska-Waszkiewicz, Agnieszka; Piesiak-Pa?czyszyn, Dagmara; Kosior, Piotr; Dobrzy?ski, Maciej

2016-01-01

Introduction. Polymerization of light-cured dental materials used for restoration of hard tooth tissue may lead to an increase in temperature that may have negative consequence for pulp vitality. Aim. The aim of this study was to determine maximum temperatures reached during the polymerization of selected dental materials, as well as the time that is needed for samples of sizes similar to those used in clinical practice to reach these temperatures. Materials and Methods. The study involved fo...

Hazardous Materials Management and Emergency Response (HAMMER)

Data.gov (United States)

Federal Laboratory Consortium — The Volpentest Hazardous Materials Management and Emergency Response (HAMMER) Federal Training Center is a safety and emergency response training center that offers...

Risk management of onsite transportation of hazardous materials

International Nuclear Information System (INIS)

Wang, O.S.; Field, J.G.

1992-10-01

The US Department of Energy's (DOE) Hanford Site has recently undergone a significant change in its mission. The focus of site-wide operations has been shifted from production to environmental restoration. As a result, there is a significant increase in quantities of the radioactive wastes and other hazardous materials to be packaged and transported onsite. In response to the elevated transportation activities, the operations and engineering contractor for the Hanford Site, Westinghouse Hanford Company (Westinghouse Hanford), is proposing an integrated risk assessment methodology and risk management strategy to further enhance the safe operations of the onsite packaging and transportation activities involving radioactive and other hazardous materials. This paper summarizes Westinghouse Hanford's proposed risk assessment and risk management methodology for onsite transportation of hazardous materials. The proposed Westinghouse Hanford risk assessment and management methodology for onsite packaging and transportation has three integral parts: risk assessment, risk acceptance criteria, and risk minimization process. The purposes are to ensure that the risk for each ongoing transportation activity is acceptable, and to further reduce the overall risk for current and future onsite transportation activities

Regional risk associated with the transport of hazardous materials

OpenAIRE

Nardini, L.; Aparicio, L.; Bandoni, A.; Tonelli, S. M.

2003-01-01

An increasing concern over the level of risk associated with hazardous materials transportation has led international efforts to focus on risk assessment at regional level. Following this trend, the aim of this work is to review the latest procedures for analysing the regional risks resulting from hazardous materials transportation by means of road and rail. In particular, two methodologies are reviewed and discussed, a method recently developed at Swiss Federal Institute of Technology [1] an...

Toward a federal/state/local partnership in hazardous materials transportation safety

International Nuclear Information System (INIS)

1982-09-01

In recognition of the federal government's responsibility for initiating a national strategy for hazardous materials transportation safety, the Materials Transportation Bureau (MTB) prepared an internal strategy paper for creating a federal/state/local partnership in hazardous materials transportation safety in August 1981. The paper outlined the scope of the hazardous materials transportation problem and established MTB's approach for creating an intergovernmental partnership for its resolution. This paper represents an update and refinement of the original plan, and is designed to chart the direction of the emerging federal/state/local relationship. The cornerstone of the plan remains the establishment of a single national set of safety regulations. It is on achievement of this objective that MTB's plan for development of enforcement, training, and emergency response capabilities at all levels of government is based. Chapter I introduces the problem with a desription of the economic importance of hazardous materials and discusses its implications for public safety. Chapter II defines the appropriate role for each level of government in the areas of rulemaking, enforcement, emergency response, and education. Chapter III demonstrates the need for uniform national safety standards and describes the economic and safety benefits of this approach. Chapter IV contains a detailed description of MTB's program for developing a successful intergovernmental partnership in hazardous materials transportation safety

Environmental risk analysis of hazardous material rail transportation

Energy Technology Data Exchange (ETDEWEB)

Saat, Mohd Rapik, E-mail: mohdsaat@illinois.edu [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Werth, Charles J.; Schaeffer, David [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Yoon, Hongkyu [Sandia National Laboratories, Albuquerque, NM 87123 (United States); Barkan, Christopher P.L. [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States)

2014-01-15

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials.

Environmental risk analysis of hazardous material rail transportation

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Werth, Charles J.; Schaeffer, David; Yoon, Hongkyu; Barkan, Christopher P.L.

2014-01-01

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

Hazardous materials sensing: An electrical metamaterial approach

Energy Technology Data Exchange (ETDEWEB)

Rawat, Vaishali; Kitture, Rohini [Department of Applied Physics, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Kumari, Dimple [Department of Applied Chemistry, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Rajesh, Harsh [Society for Applied Microwave Electronics Engineering and Research (SAMEER), IIT-Bombay Campus, Powai, Mumbai (India); Banerjee, Shaibal [Department of Applied Chemistry, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Kale, S.N., E-mail: sangeetakale2004@gmail.com [Department of Applied Physics, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India)

2016-10-01

Metamaterials are recently emerging materials exhibiting amazing properties such as extremely miniaturized antennas, waveguides, optical couplers, multiplexers and filters. Such structures also respond to the variation in their ambient conditions when exposed to toxic and hazardous materials, which are especially hazardous to human health. Through this manuscript, we document our studies on three different high energy materials; namely 2- bromo-2nitropropane-1,3-diol (BNP), bis (1,3-diazido prop-2-yl) malonate (AM) and bis (1,3-diazido prop-2-yl) glutarate (AG). A Complementary Split Ring Resonator has been fabricated at resonant frequency of 4.48 GHz using copper on FR4 substrate. The energetic materials were exposed to the sensor and results were monitored using Vector Network Analyzer. The volume of liquids was varied from 0.5 µL to 3 µL. Prominent and explicit shifts in the transmission resonant frequency and amplitude was seen as a signature of each energetic material. The signatures were not only sensitive to the specific toxic group in the material but also to the volume of the liquid subjected to this sensor. The results are correlated with the simulation results, basic chemistry of the materials and permittivity measurements. The ultra-fast reversibility and repeatability, with good sensitivity and specificity of these devices project their applications in sensitive locations, particularly to combat for human security and health issues.

49 CFR 172.202 - Description of hazardous material on shipping papers.

Science.gov (United States)

2010-10-01

... papers. 172.202 Section 172.202 Transportation Other Regulations Relating to Transportation PIPELINE AND... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Shipping Papers § 172.202 Description of hazardous material on shipping papers. (a) The shipping description of a hazardous material on the shipping paper...

A study of risk evaluation methodology selection for the external hazards

International Nuclear Information System (INIS)

Kuramoto, Takahiro; Yamaguchi, Akira; Narumiya, Yosiyuki

2014-01-01

Since the accident at Fukushima Daiichi Nuclear Power Plant caused by the Great East Japan Earthquake in March 2011, there has been growing demands for assessing the effects of external hazards, including natural events, such as earthquake and tsunami, and external human behaviors, and taking actions to address those external hazards. The newly established Japanese regulatory requirements claim design considerations associated with external hazards. The primary objective of the risk assessment for external hazards is to establish countermeasures against such hazards rather than grasping the risk figures. Therefore, applying detailed risk assessment methods, such as probabilistic risk assessment (PRA), to all the external hazards is not always the most appropriate. Risk assessment methods can vary in types including qualitative evaluation, hazard analysis (analyzing hazard frequencies or their influence), and margin assessment. To resolve these issues, a process has been established that enables us to identify the external hazards in a comprehensive and systematic manner, which have potential risks leading to core damage and to select an appropriate evaluation method according to the risks associated with each of the external hazards. This paper discusses the comprehensive and systematic identification process for the external hazards which have potential risks leading to core damage, and the approaches of selecting an appropriate evaluation method for each external hazard. This paper also describes some applications of specific risk evaluation methods. (author)

Hazardous materials management and compliance training

International Nuclear Information System (INIS)

Dalton, T.F.

1991-01-01

OSHA training for hazardous waste site workers is required by the Superfund Amendments and Reauthorization Act of 1986 (SARA). In December 1986, a series of regulations was promulgated by OSHA on an interim basis calling for the training of workers engaged in hazardous waste operations. Subsequent to these interim regulations, final rules were promulgated and these final rules on hazardous waste operations and emergency response became effective on March 6, 1990. OSHA has conducted hearings on the accreditation of training programs. OSHA would like to follow the accreditation process under the AHERA regulations for asbestos, in which the model plan for accreditation of asbestos abatement training was included in Section 206 of Title 11 of the Toxic Substance Control Act (TSCA). OSHA proposed on January 26, 1990, to perform the accreditation of training programs for hazardous waste operations and that proposal suggested that they follow the model plan similar to the one used for AHERA. They did not propose to accredited training programs for workers engaged in emergency response. These new regulations pose a significant problem to the various contractors and emergency responders who deal with hazardous materials spill response, cleanup and site remediation since these programs have expanded so quickly that many people are not familiar with what particular segment of the training they are required to have and whether or not programs that have yet to be accredited are satisfactory for this type of training. Title III of SARA stipulates a training program for first responders which includes local emergency response organizations such as firemen and policemen. The purpose of this paper is to discuss the needs of workers at hazardous waste site remediation projects and workers who are dealing with hazardous substances, spill response and cleanup

Hazardous materials transportation and emergency response programs

International Nuclear Information System (INIS)

Joy, D.S.; Fore, C.S.

1983-01-01

This presentation consists of the following visual aids; (1) detailed routing capabilities of truck, rail, barge; (2) legislative data base for hazardous materials; and (3) emergency response of accident site Eddyville, Kentucky (airports in vicinity of Eddyville, KY)

A Decision Support Model Using Life Cycle Cost (LCC) Analysis to Select Cost-Effective Alternatives for Hazardous Materials

Science.gov (United States)

1993-09-01

AF89-071. Washington: GPO, 1989. 159 14. Diaz , SSgt Laura, 648 Med Sq/SGHL. Personal interview. Brooks AFB, San Antonio TX, 14 July 1993. 15. EA...Training Strateav of the Acauisition Management of Hazardous Materials Program. Draft Report. McLean VA, August 1991. 36. Moore, SSgt Alicia . AL/OEVP

Integrating Hazardous Materials Characterization and Assessment Tools to Guide Pollution Prevention in Electronic Products and Manufacturing

Science.gov (United States)

Lam, Carl

Due to technology proliferation, the environmental burden attributed to the production, use, and disposal of hazardous materials in electronics have become a worldwide concern. The major theme of this dissertation is to develop and apply hazardous materials assessment tools to systematically guide pollution prevention opportunities in the context of electronic product design, manufacturing and end-of-life waste management. To this extent, a comprehensive review is first provided on describing hazard traits and current assessment methods to evaluate hazardous materials. As a case study at the manufacturing level, life cycle impact assessment (LCIA)-based and risk-based screening methods are used to quantify chemical and geographic environmental impacts in the U.S. printed wiring board (PWB) industry. Results from this industrial assessment clarify priority waste streams and States to most effectively mitigate impact. With further knowledge of PWB manufacturing processes, select alternative chemical processes (e.g., spent copper etchant recovery) and material options (e.g., lead-free etch resist) are discussed. In addition, an investigation on technology transition effects for computers and televisions in the U.S. market is performed by linking dynamic materials flow and environmental assessment models. The analysis forecasts quantities of waste units generated and maps shifts in environmental impact potentials associated with metal composition changes due to product substitutions. This insight is important to understand the timing and waste quantities expected and the emerging toxic elements needed to be addressed as a consequence of technology transition. At the product level, electronic utility meter devices are evaluated to eliminate hazardous materials within product components. Development and application of a component Toxic Potential Indicator (TPI) assessment methodology highlights priority components requiring material alternatives. Alternative

Automated accountability of hazardous materials at AlliedSignal Inc., Kansas City Division

International Nuclear Information System (INIS)

Depew, P.L.

1993-12-01

The Department of Energy's (DOE) Kansas City Plant (KCP), currently operated by AlliedSignal Inc. has developed a comprehensive Hazardous Material Information System (HMIS). The purpose of this system is to provide a practical and automated method to collect, analyze and distribute hazardous material information to DOE, KCP associates, and regulatory agencies. The drivers of the HMIS are compliance with OSHA Hazard Communications, SARA reporting, pollution prevention, waste minimization, control and tracking of hazards, and emergency response. This report provides a discussion of this system

Assessment of Heat Hazard during the Polymerization of Selected Light-Sensitive Dental Materials.

Science.gov (United States)

Janeczek, Maciej; Herman, Katarzyna; Fita, Katarzyna; Dudek, Krzysztof; Kowalczyk-Zając, Małgorzata; Czajczyńska-Waszkiewicz, Agnieszka; Piesiak-Pańczyszyn, Dagmara; Kosior, Piotr; Dobrzyński, Maciej

2016-01-01

Introduction. Polymerization of light-cured dental materials used for restoration of hard tooth tissue may lead to an increase in temperature that may have negative consequence for pulp vitality. Aim. The aim of this study was to determine maximum temperatures reached during the polymerization of selected dental materials, as well as the time that is needed for samples of sizes similar to those used in clinical practice to reach these temperatures. Materials and Methods. The study involved four composite restorative materials, one lining material and a dentine bonding agent. The polymerization was conducted with the use of a diode light-curing unit. The measurements of the external surface temperature of the samples were carried out using the Thermovision®550 thermal camera. Results. The examined materials significantly differed in terms of the maximum temperatures values they reached, as well as the time required for reaching the temperatures. A statistically significant positive correlation of the maximum temperature and the sample weight was observed. Conclusions. In clinical practice, it is crucial to bear in mind the risk of thermal damage involved in the application of light-cured materials. It can be reduced by using thin increments of composite materials.

Evaluation of Hazardous Material Management Safety in the Chemical Laboratory in BATAN

International Nuclear Information System (INIS)

Nur-Rahmah-Hidayati

2005-01-01

The management safety of the hazardous material (B3) in the chemical laboratory of BATAN was evaluated. The evaluation is necessary to be done because B3 is often used together with radioactive materials in the laboratory, but the attention to the safety aspect of B3 is not paid sufficiently in spite of its big potential hazard. The potential hazard generated from the nature of B3 could be flammable, explosive, oxidative, corrosive and poisonous. The handling of B3 could be conducted by enforcing the labelling and classification in the usage and disposal processes. Some observations of the chemical laboratory of BATAN show that the management safety of hazardous material in compliance with the government regulation no. 74 year 2001 has not been dully conducted. The management safety of B3 could be improved by, designating one who has adequate skill in hazardous material safety specially as the B3 safety officer, providing the Material Safety Data Sheet that is updated periodically to use in the laboratory and storage room, updating periodically the inventory of B3, performing training in work safety periodically, and monitoring the ventilation system intensively in laboratory and storage room. (author)

Integrated risk reduction framework to improve railway hazardous materials transportation safety.

Science.gov (United States)

Liu, Xiang; Saat, M Rapik; Barkan, Christopher P L

2013-09-15

Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation. Copyright © 2013 Elsevier B.V. All rights reserved.

Sandia National Laboratories, California Hazardous Materials Management Program annual report.

Energy Technology Data Exchange (ETDEWEB)

Brynildson, Mark E.

2011-02-01

The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. This program annual report describes the activities undertaken during the calender past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

40 CFR Table 16 to Subpart Xxxx of... - Selected Hazardous Air Pollutants

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Selected Hazardous Air Pollutants 16 Table 16 to Subpart XXXX of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED.... XXXX, Table 16 Table 16 to Subpart XXXX of Part 63—Selected Hazardous Air Pollutants You must use the...

Hazardous materials management and control program at Oak Ridge National Laboratory - environmental protection

International Nuclear Information System (INIS)

Eisenhower, B.M.; Oakes, T.W.

1982-01-01

In the Federal Register of May 19, 1980, the US Environmental Protection Agency promulgated final hazardous waste regulations according to the Resource Conservation and Recovery Act (RCRA) of 1976. The major substantive portions of these regulations went into effect on November 19, 1980, and established a federal program to provide comprehensive regulation of hazardous waste from its generation to its disposal. In an effort to comply with these regulations, a Hazardous Materials Management and Control Program was established at Oak Ridge National Laboratory. The program is administered by two Hazardous Materials Coordinators, who together with various support groups, ensure that all hazardous materials and wastes are handled in such a manner that all personnel, the general public, and the environment are adequately protected

Natural and technologic hazardous material releases during and after natural disasters: a review.

Science.gov (United States)

Young, Stacy; Balluz, Lina; Malilay, Josephine

2004-04-25

Natural disasters may be powerful and prominent mechanisms of direct and indirect hazardous material (hazmat) releases. Hazardous materials that are released as the result of a technologic malfunction precipitated by a natural event are referred to as natural-technologic or na-tech events. Na-tech events pose unique environmental and human hazards. Disaster-associated hazardous material releases are of concern, given increases in population density and accelerating industrial development in areas subject to natural disasters. These trends increase the probability of catastrophic future disasters and the potential for mass human exposure to hazardous materials released during disasters. This systematic review summarizes direct and indirect disaster-associated releases, as well as environmental contamination and adverse human health effects that have resulted from natural disaster-related hazmat incidents. Thorough examination of historic disaster-related hazmat releases can be used to identify future threats and improve mitigation and prevention efforts.

Assessment of Heat Hazard during the Polymerization of Selected Light-Sensitive Dental Materials

Directory of Open Access Journals (Sweden)

Maciej Janeczek

2016-01-01

Full Text Available Introduction. Polymerization of light-cured dental materials used for restoration of hard tooth tissue may lead to an increase in temperature that may have negative consequence for pulp vitality. Aim. The aim of this study was to determine maximum temperatures reached during the polymerization of selected dental materials, as well as the time that is needed for samples of sizes similar to those used in clinical practice to reach these temperatures. Materials and Methods. The study involved four composite restorative materials, one lining material and a dentine bonding agent. The polymerization was conducted with the use of a diode light-curing unit. The measurements of the external surface temperature of the samples were carried out using the Thermovision®550 thermal camera. Results. The examined materials significantly differed in terms of the maximum temperatures values they reached, as well as the time required for reaching the temperatures. A statistically significant positive correlation of the maximum temperature and the sample weight was observed. Conclusions. In clinical practice, it is crucial to bear in mind the risk of thermal damage involved in the application of light-cured materials. It can be reduced by using thin increments of composite materials.

Transportation of hazardous materials in Iran: A strategic approach for decreasing accidents

Directory of Open Access Journals (Sweden)

S. Ghazinoory

2008-06-01

Full Text Available .“Hazardous materials” refer to those substances that seriously endanger human lives and/or the environment. The transportation of these materials will be inevitable in the increasingly industrialized economy of Iran. Nonetheless, numerous deadly accidents caused by the movement of these materials necessitate the design and implementation of preventive plans on several levels. This article looks into the present condition of transportation of hazardous materials in Iran and the resulting accidents. Optimal condition for the general transportation system of hazardous materials is delineated with due focus on transportation risk as the main parameter. Strategies for reaching the optimal condition are laid out and the impacts of these strategies on the reduction of accidents are analyzed.

A five-year history of hazardous materials incidents in Chester County, PA

International Nuclear Information System (INIS)

Shorten, C.V.; McNamara, J.

1993-01-01

The Emergency Planning and Community Right-to-Know Act (EPCRA) of 1986 established Local Emergency Planning Committees (LEPCs) to oversee emergency response planning at the community level. In Pennsylvania, each county was assigned its own LEPC, and Chester County held its first LEPC meeting on October 15, 1987. From the data of that meeting through September 1992, 300 hazardous materials incidents have been reported. The majority of these incidents were met with fire department response, but several warranted response by hazardous materials teams. This report presents an analysis of the database of reported hazardous materials incidents in Chester County, including chemical identification, amount released, type of response, location, and trends. Over 235 of the reported spills were either gasoline, diesel fuel, home heating oil, or kerosene, often in five to 50 gallon amounts from transportation accidents. A number of extremely hazardous substance (EHS) incidents were reported, however, including sulfuric acid, chlorine, ammonia, phosphorus, formaldehyde, bromine, methyl mercaptan, and hydrofluoric acid. The most commonly released EHS's were ammonia and chlorine. The number of hazardous materials incidents reported in Chester County increased from only 14 in 1988 to 95 in 1991, with 67 in 1992 through September. This dramatic increase is attributable to both increased reporting and an increased number of incidents. This database clearly indicates both the success of EPCRA reporting system and the magnitude of hazardous materials incidents in this part of Pennsylvania

49 CFR 176.99 - Permit requirements for certain hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Permit requirements for certain hazardous materials. 176.99 Section 176.99 Transportation Other Regulations Relating to Transportation PIPELINE AND... CARRIAGE BY VESSEL Special Requirements for Barges § 176.99 Permit requirements for certain hazardous...

Storage and transport of hazardous materials

International Nuclear Information System (INIS)

Jaeger, P.; Haferkamp, K.

1986-01-01

The attempt has been made to characterise the present risk scenario, and to set out approaches or methods for remedy and risk control. For this purpose, a retrospective analysis has been made of accidents, damage and consequential damage that occurred in the past either during storage of hazardous materials, or during road transport. A risk-benefit model facilitates assessment of accident frequency. The history of accidents during storage or transport allows assessment of the dangerousness of various materials. Another important aspect discussed is the property and behaviour of containers used for storage or transport. (DG) [de

Perceived safety of transporting hazardous materials

International Nuclear Information System (INIS)

Reese, R.T.; Shepherd, E.W.

1981-01-01

A framework for relating the variables involved in the public perception of hazardous materials transportation was presented. The framework consisted of a conditional mathematical equation in which perceived safety was described by six basic terms (technical feasibility, political palatability, social responsibility, utility assessment, media interpretation, and familiarity as a function of time). The resulting framework provides the technologist with an initial formulation to better understand public perception

GIS risk analysis of hazardous materials transport

International Nuclear Information System (INIS)

Anders, C.; Olsten, J.

1991-01-01

The Geographic Information System (GIS) was used to assess the risks and vulnerability of transporting hazardous materials and wastes (such as gasoline, explosives, poisons, etc) on the Arizona highway system. This paper discusses the methodology that was utilized, and the application of GIS systems to risk analysis problems

Materials Selection And Fabrication Practices For Food Processing Equipment Manufacturers In Uganda

Directory of Open Access Journals (Sweden)

John Baptist Kirabira

2017-08-01

Full Text Available The food processing industry is one of the fast-growing sub-sectors in Uganda. The industry which is majorly composed of medium and small scale firms depends on the locally developed food processing equipment. Due to lack of effective materials selection practices employed by the equipment manufacturers the materials normally selected for most designs are not the most appropriate ones hence compromising the quality of the equipment produced. This has not only led to poor quality food products due to contamination but could also turn out health hazardous to the consumers of the food products. This study involved the assessment of the current materials selection and fabrication procedures used by the food processing equipment manufacturers with a view of devising best practices that can be used to improve the quality of the food products processed by the locally fabricated equipment. Results of the study show that designers experience biasness and desire to minimize cost compromise the materials selection procedure. In addition to failing to choose the best material for a given application most equipment manufacturers are commonly fabricating equipment with inadequate surface finish and improper weldments. This hinders the equipments ability to meet food hygiene standards.

Feasibility study--computerized application of the hazardous material regulations

International Nuclear Information System (INIS)

Ferrada, J.J.; Green, V.M.; Rawl, R.R.

1992-09-01

The feasibility of developing a full expert system for transportation and packaging of hazardous and radioactive materials was initiated within the framework of three subtasks: (1) analysis of commercial packages related to regulation scanning, (2) analysis of computer languages to develop the expert system, and (3) development of expert system prototypes. The strategy to develop the latter subtask was to first,develop modules to capture the knowledge of different areas of transportation and packaging and second, to analyze the feasibility of appending these different modules in one final full package. The individual modules development contemplated one prototype for transporting and packaging of radioactive material and another for transporting hazardous chemical materials. In the event that it is not feasible to link these two packages, the modules can always be used as stand-alone tools, or linked as a single package with some restrictions in their applicability. The work done during this fiscal year has focused on developing a prototype for transporting radioactive materials

78 FR 60726 - Hazardous Materials Regulations: Penalty Guidelines

Science.gov (United States)

2013-10-02

... new categories: Offeror Requirements for specific hazardous materials: Oxygen Generators and Batteries... protecting public health, welfare, safety, and our environment.'' Executive Order 13610 further instructs... the human environment. When developing potential regulatory requirements, PHMSA evaluates those...

Hazardous materials management using a Cradle-to-Grave Tracking and Information System (CGTIS)

Energy Technology Data Exchange (ETDEWEB)

Kjeldgaard, E.; Fish, J.; Campbell, D.; Freshour, N.; Hammond, B.; Bray, O. [Sandia National Labs., Albuquerque, NM (United States); Hollingsworth, M. [Ogden Environmental & Energy Services Co., Inc., Albuquerque, NM (United States)

1995-03-01

Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site`s environmental, safety & health (ES&H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site`s multitude of data bases to bring information together into one common data model.

Hazardous materials management using a Cradle-to-Grave Tracking and Information System (CGTIS)

International Nuclear Information System (INIS)

Kjeldgaard, E.; Fish, J.; Campbell, D.; Freshour, N.; Hammond, B.; Bray, O.; Hollingsworth, M.

1995-03-01

Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site's environmental, safety ampersand health (ES ampersand H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site's multitude of data bases to bring information together into one common data model

Transport and Reactivity of Decontaminants to Provide Hazard Mitigation of Chemical Warfare Agents from Materials

Science.gov (United States)

2016-06-01

2013 4. TITLE AND SUBTITLE Transport and Reactivity of Decontaminants to Provide Hazard Mitigation of Chemical Warfare Agents from Materials 5a...directions for future decontamination formulation approaches. 15. SUBJECT TERMS GD HD Decontamination Hazard mitigation VX Chemical warfare agent... DECONTAMINANTS TO PROVIDE HAZARD MITIGATION OF CHEMICAL WARFARE AGENTS FROM MATERIALS 1. INTRODUCTION Decontamination of materials is the

Basic Versus Supplementary Health Insurance : Moral Hazard and Adverse Selection

NARCIS (Netherlands)

Boone, J.

2014-01-01

This paper introduces a tractable model of health insurance with both moral hazard and adverse selection. We show that government sponsored universal basic insurance should cover treatments with the biggest adverse selection problems. Treatments not covered by basic insurance can be covered on the

Basic versus supplementary health insurance : Moral hazard and adverse selection

NARCIS (Netherlands)

Boone, J.

This paper introduces a tractable model of health insurance with both moral hazard and adverse selection. We show that government sponsored universal basic insurance should cover treatments with the biggest adverse selection problems. Treatments not covered by basic insurance can be covered on the

Hazardous Materials Verification and Limited Characterization Report on Sodium and Caustic Residuals in Materials and Fuel Complex Facilities MFC-799/799A

Energy Technology Data Exchange (ETDEWEB)

Gary Mecham

2010-08-01

This report is a companion to the Facilities Condition and Hazard Assessment for Materials and Fuel Complex Sodium Processing Facilities MFC-799/799A and Nuclear Calibration Laboratory MFC-770C (referred to as the Facilities Condition and Hazards Assessment). This report specifically responds to the requirement of Section 9.2, Item 6, of the Facilities Condition and Hazards Assessment to provide an updated assessment and verification of the residual hazardous materials remaining in the Sodium Processing Facilities processing system. The hazardous materials of concern are sodium and sodium hydroxide (caustic). The information supplied in this report supports the end-point objectives identified in the Transition Plan for Multiple Facilities at the Materials and Fuels Complex, Advanced Test Reactor, Central Facilities Area, and Power Burst Facility, as well as the deactivation and decommissioning critical decision milestone 1, as specified in U.S. Department of Energy Guide 413.3-8, “Environmental Management Cleanup Projects.” Using a tailored approach and based on information obtained through a combination of process knowledge, emergency management hazardous assessment documentation, and visual inspection, this report provides sufficient detail regarding the quantity of hazardous materials for the purposes of facility transfer; it also provides that further characterization/verification of these materials is unnecessary.

77 FR 24885 - Hazardous Materials; Miscellaneous Amendments (RRR)

Science.gov (United States)

2012-04-26

... special provisions, clarify the lab pack requirements for temperature-controlled materials, and revise the... in Dewar flasks. Clarify the lab pack provisions in Sec. 173.12 pertaining to temperature-controlled... shipping names, hazard classes, packing groups, special provisions, packaging authorizations, air transport...

Calculation of Airborne Radioactivity Hazard from Machining Volume-Activated Materials

International Nuclear Information System (INIS)

E.T. Marshall; S.O. Schwahn

1997-01-01

When evaluating a task involving the machining of volume-activated materials, accelerator health physicists must consider more than the surface contamination levels of the equipment and containment of loose shavings, dust or filings. Machining operations such as sawing, routing, welding, and grinding conducted on volume-activated material may pose a significant airborne radioactivity hazard to the worker. This paper presents a computer spreadsheet notebook that conservatively estimates the airborne radioactivity levels generated during machining operations performed on volume-activated materials. By knowing (1) the size and type of materials, (2) the dose rate at a given distances, and (3) limited process knowledge, the Derived Air Concentration (DAC) fraction can be estimated. This tool is flexible, taking into consideration that the process knowledge available for the different materials varies. It addresses the two most common geometries: thick plane and circular cylinder. Once the DAC fraction has been estimated, controls can be implemented to mitigate the hazard to the worker

Calculation of airborne radioactivity hazard from machining volume-activated materials

International Nuclear Information System (INIS)

Marshall, E.T.; Schwahn, S.O.

1996-10-01

When evaluating a task involving the machining of volume-activated materials, accelerator health physicists must consider more than the surface contamination levels of the equipment and containment of loose shavings, dust or filings. Machining operations such as sawing, routing, welding, and grinding conducted on volume-activated material may pose a significant airborne radioactivity hazard to the worker. This paper presents a computer spreadsheet notebook that conservatively estimates the airborne radioactivity levels generated during machining operations performed on volume-activated materials. By knowing (1) the size and type of materials, (2) the dose rate at a given distances, and (3) limited process knowledge, the Derived Air Concentration (DAC) fraction can be estimated. This tool is flexible, taking into consideration that the process knowledge available for the different materials varies. It addresses the two most common geometries: thick plane and circular cylinder. Once the DAC fraction has been estimated, controls can be implemented to mitigate the hazard to the worker

Project plan, Hazardous Materials Management and Emergency Response Training Center: Project 95L-EWT-100

International Nuclear Information System (INIS)

Borgeson, M.E.

1994-01-01

The Hazardous Materials Management and Emergency Response (HAMMER) Training Center will provide for classroom lectures and hands-on practical training in realistic situations for workers and emergency responders who are tasked with handling and cleanup of toxic substances. The primary objective of the HAMMER project is to provide hands-on training and classroom facilities for hazardous material workers and emergency responders. This project will also contribute towards complying with the planning and training provisions of recent legislation. In March 1989 Title 29 Code of Federal Regulations Occupational Safety and Health Administration 1910 Rules and National Fire Protection Association Standard 472 defined professional requirements for responders to hazardous materials incidents. Two general types of training are addressed for hazardous materials: training for hazardous waste site workers and managers, and training for emergency response organizations

78 FR 16044 - Hazardous Materials Packaging-Composite Cylinder Standards; Public Meeting

Science.gov (United States)

2013-03-13

... Toughiry, Engineering and Research Division, Office of Hazardous Materials Safety, Pipeline and Hazardous... the HMR, ISO 11119 Parts-1, -2 and -3, contain design, construction and testing requirements that are.../permits-approvals/special-permits . II. Public Meeting Topics During this public meeting, PHMSA will...

Preparedness of hazardous materials emergencies in railyards: Guidance for railroads and adjacent communities

Energy Technology Data Exchange (ETDEWEB)

1991-09-01

Railroads are a key part of the distribution system for hazardous materials and, thus, much hazardous material passes through railyards en route to intermediate or final consumers. While the vast majority of these materials are shipped without incident, both the number of shipments and the nature of the materials themselves dictate that railyards and surrounding communities be prepared to respond quickly and effectively to emergencies. This report contains information on 11 emergency preparedness functions and 150 guidance recommendations.

Radioactivity and associated radiation hazards in ceramic raw materials and end products.

Science.gov (United States)

Viruthagiri, G; Rajamannan, B; Suresh Jawahar, K

2013-12-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of (226)Ra, (232)Th and (40)K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants.

Radioactivity and associated radiation hazards in ceramic raw materials and end products

International Nuclear Information System (INIS)

Viruthagiri, G.; Rajamannan, B.; Suresh Jawahar, K.

2013-01-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of 226 Ra, 232 Th and 40 K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants. (authors)

Numerical investigation of debris materials prior to debris flow hazards using satellite images

Science.gov (United States)

Zhang, N.; Matsushima, T.

2018-05-01

The volume of debris flows occurred in mountainous areas is mainly affected by the volume of debris materials deposited at the valley bottom. Quantitative evaluation of debris materials prior to debris flow hazards is important to predict and prevent hazards. At midnight on 7th August 2010, two catastrophic debris flows were triggered by the torrential rain from two valleys in the northern part of Zhouqu City, NW China, resulting in 1765 fatalities and huge economic losses. In the present study, a depth-integrated particle method is adopted to simulate the debris materials, based on 2.5 m resolution satellite images. In the simulation scheme, the materials are modeled as dry granular solids, and they travel down from the slopes and are deposited at the valley bottom. The spatial distributions of the debris materials are investigated in terms of location, volume and thickness. Simulation results show good agreement with post-disaster satellite images and field observation data. Additionally, the effect of the spatial distributions of the debris materials on subsequent debris flows is also evaluated. It is found that the spatial distributions of the debris materials strongly influence affected area, runout distance and flow discharge. This study might be useful in hazard assessments prior to debris flow hazards by investigating diverse scenarios in which the debris materials are unknown.

Mission: Possible. Center of Excellence for Hazardous Materials Management

International Nuclear Information System (INIS)

Bartlett, W.T.; Prather-Stroud, W.

2006-01-01

The Center of Excellence for Hazardous Materials Management (CEHMM) was established in May 2004 as a nonprofit research organization. Its purpose is to develop a sustainable technical/scientific community located in Carlsbad, New Mexico, that interacts worldwide to find solutions to hazardous materials management issues. An important part of the mission is to achieve improved protection of worker safety, human health, and the environment. Carlsbad has a large technical community due to the presence of the Waste Isolation Pilot Plant (WIPP) and its many contractors and support organizations. These groups include the Carlsbad Environmental Monitoring and Research Center, Washington Group International, Los Alamos National Laboratory, and Sandia National Laboratories. These organizations form the basis of a unique knowledge community with strengths in many areas, such as geosciences, actinide chemistry, environmental monitoring, and waste transportation. CEHMM works cooperatively with these organizations and others to develop projects that will maintain this knowledge community beyond the projected closure date of WIPP. At present, there is an emphasis in bio-monitoring, air monitoring, hazardous materials educational programs, and endangered species remediation. CEHMM is also currently working with a group from the American Nuclear Society to help facilitate their conference scheduled for April 2006 in Carlsbad. CEHMM is growing rapidly and is looking forward to a diverse array of new projects. (authors)

Transport of hazardous materials in the Amazon area; Transporte de produtos perigosos na regiao Amazonica

Energy Technology Data Exchange (ETDEWEB)

Cunha, Wallace de Castro [FURNAS Centrais Eletricas S.A., Rio de Janeiro, RJ (Brazil); Fernandes, Elton; Nassi, Carlos David [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Amongst several exploratory sources of the subject 'hazardous materials transport', it is distinguished: 'the threat to the environment'. This paper presents an exploratory investigation of this subject line in the Amazon region. In view of the diversity of 'existing hazardous materials' and the raised dimension of the oil transport and its derivatives in this context, this paper focused in these products. Regarding to the geographic region, the approach was given to the State of Amazon, considering the amplitude of this State in the Amazon region and the availability of data. Therefore, this work explores and analyzes macro aspects inherent to the State of Amazon pertinent to the oil transport and its derivatives. In the macro context, it is observed the necessity of a higher control in the transport of hazardous materials in the region. The absence of registered data and the unfamiliarity on the risks related to the transport of hazardous materials by authorities and transporters indicate a relative absence of qualification in the region to deal with the monitoring of the transport of hazardous materials. So far, it is not possible up till now to make any evaluation of the environment threats of accidents with transport of hazardous materials in the Amazon region.(author)

Transport of hazardous materials in the Amazon area; Transporte de produtos perigosos na regiao Amazonica

Energy Technology Data Exchange (ETDEWEB)

Cunha, Wallace de Castro [FURNAS Centrais Eletricas S.A., Rio de Janeiro, RJ (Brazil); Fernandes, Elton; Nassi, Carlos David [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Amongst several exploratory sources of the subject 'hazardous materials transport', it is distinguished: 'the threat to the environment'. This paper presents an exploratory investigation of this subject line in the Amazon region. In view of the diversity of 'existing hazardous materials' and the raised dimension of the oil transport and its derivatives in this context, this paper focused in these products. Regarding to the geographic region, the approach was given to the State of Amazon, considering the amplitude of this State in the Amazon region and the availability of data. Therefore, this work explores and analyzes macro aspects inherent to the State of Amazon pertinent to the oil transport and its derivatives. In the macro context, it is observed the necessity of a higher control in the transport of hazardous materials in the region. The absence of registered data and the unfamiliarity on the risks related to the transport of hazardous materials by authorities and transporters indicate a relative absence of qualification in the region to deal with the monitoring of the transport of hazardous materials. So far, it is not possible up till now to make any evaluation of the environment threats of accidents with transport of hazardous materials in the Amazon region.(author)

Hazard analysis in uranium hexafluoride production facility

International Nuclear Information System (INIS)

Marin, Maristhela Passoni de Araujo

1999-01-01

The present work provides a method for preliminary hazard analysis of nuclear fuel cycle facilities. The proposed method identify both chemical and radiological hazards, as well as the consequences associated with accident scenarios. To illustrate the application of the method, a uranium hexafluoride production facility was selected. The main hazards are identified and the potential consequences are quantified. It was found that, although the facility handles radioactive material, the main hazards as associated with releases of toxic chemical substances such as hydrogen fluoride, anhydrous ammonia and nitric acid. It was shown that a contention bung can effectively reduce the consequences of atmospheric release of toxic materials. (author)

Materials selection in mechanical design

International Nuclear Information System (INIS)

Ashby, M.F.; Cebon, D.

1993-01-01

A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimisation methods are employed for simultaneous selection of both material and shape. (orig.)

Materials selection in mechanical design

OpenAIRE

Ashby , M.; Cebon , D.

1993-01-01

A novel materials-selection procedure has been developed and implemented in software. The procedure makes use of Materials Selection Charts: a new way of displaying material property data; and performance indices: combinations of material properties which govern performance. Optimisation methods are employed for simultaneous selection of both material and shape.

75 FR 38168 - Hazardous Materials: International Regulations for the Safe Transport of Radioactive Material (TS...

Science.gov (United States)

2010-07-01

... may also provide contact information, such as a telephone number and/or e-mail address. PHMSA and the.... PHMSA-2010-0130 (Notice No.10-2)] Hazardous Materials: International Regulations for the Safe Transport... (IAEA) ``Regulations for the Safe Transport of Radioactive Material'' (TS-R-1), which is scheduled for...

Sandia National Laboratories, California Hazardous Materials Management Program annual report : February 2009.

Energy Technology Data Exchange (ETDEWEB)

Brynildson, Mark E.

2009-02-01

The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental anagement ystem Program Manual. This program annual report describes the activities undertaken during the past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

Quality Assurance Program Plan for the Hazardous Materials Transportation and Packaging Program. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Calihan, T.W. III; Votaw, E.F.

1995-05-01

This QAPP covers only the implementation accomplished through Level I and II manuals. It covers the quality affecting activities identified in USDOE orders (both HQ and Richland Operations Office), US DOT, US EPA, and NRC regulations, IAEA guidelines, and the WHC manuals. It covers activities related to hazardous materials transportation performed on and off the Hanford site under the jurisdictional authority of WHC. (Hazardous materials include radioactive, hazardous waste, and mixed waste.)

Quality Assurance Program Plan for the Hazardous Materials Transportation and Packaging Program. Revision 1

International Nuclear Information System (INIS)

Calihan, T.W. III; Votaw, E.F.

1995-01-01

This QAPP covers only the implementation accomplished through Level I and II manuals. It covers the quality affecting activities identified in USDOE orders (both HQ and Richland Operations Office), US DOT, US EPA, and NRC regulations, IAEA guidelines, and the WHC manuals. It covers activities related to hazardous materials transportation performed on and off the Hanford site under the jurisdictional authority of WHC. (Hazardous materials include radioactive, hazardous waste, and mixed waste.)

77 FR 39662 - Hazardous Materials; Reverse Logistics (RRR)

Science.gov (United States)

2012-07-05

... logistics providers estimate that up to 7% of an enterprise's gross sales are return costs. The third-party... logistic shipments for hazardous materials? III. Issues To Be Considered As previously noted, the purpose... documentation costs to develop and maintain risk assessments and operational procedures? If so, what is a fair...

Emergency response network design for hazardous materials transportation with uncertain demand

Directory of Open Access Journals (Sweden)

Kamran Shahanaghi

2012-10-01

Full Text Available Transportation of hazardous materials play an essential role on keeping a friendly environment. Every day, a substantial amount of hazardous materials (hazmats, such as flammable liquids and poisonous gases, need to be transferred prior to consumption or disposal. Such transportation may result in unsuitable events for people and environment. Emergency response network is designed for this reason where specialist responding teams resolve any issue as quickly as possible. This study proposes a new multi-objective model to locate emergency response centers for transporting the hazardous materials. Since many real-world applications are faced with uncertainty in input parameters, the proposed model of this paper also assumes that reference and demand to such centre is subject to uncertainty, where demand is fuzzy random. The resulted problem formulation is modelled as nonlinear non-convex mixed integer programming and we used NSGAII method to solve the resulted problem. The performance of the proposed model is examined with several examples using various probability distribution and they are compared with the performance of other existing method.

Sanitary Assessment of Hazardous Materials Exposed To Highly Toxic Chemical Compounds

International Nuclear Information System (INIS)

Rembovskiy, V.; Ermolaeva, E.

2007-01-01

Industrial or terroristic accidents in which toxic chemicals (TC) are the main or attendant damaging factors should be regarded as a new challenge for experts, because of little knowledge on the methodology to estimating the long-term risk for humans due to contamination of the building materials and environment. In the Russian Federation, there appeared to be a kind of model systems for developing an algorithm for solving these or similar problems. Under dismantling and liquidation of the former facilities for chemical weapon production (FCWP) the building materials are regarded as potential waste products the fate of which (processing, warehousing, utilization, and destruction) is dependent on their possible hazard for human population and environment. The standard approaches for hazard assessment of waste products of the FCWP turned out to be insufficient. When conducting the present work, the following problems have been solved: 1. Selection of representative samples taking into consideration a diversity of construction materials, great quantities of potentially toxic waste materials, information on the production conditions, breakdowns in the process of production, accidents, composition of the decontaminators used, decontamination frequency, etc. 2. Analysis of TC in composite matrixes complicated by the following problems: extraction, masking effects of concomitant components during indirect analysis, lack of certified methods of direct analysis of TC, discrepancy of results of GC and direct GCMS analysis, low sensitivity of GCMS analysis, big volume of samples (more than 0.5 kg), heterogeneity of physical-chemical properties of different matrixes influencing the process of degradation of TC. 3. Hazard assessment of the wastes in toxic-and-sanitary experiment relying on non-specific signs of intoxication due to relatively low percentage of TC and masking effects of various matrix components. Application of the integral toxicity tests with soil

49 CFR 176.76 - Transport vehicles, freight containers, and portable tanks containing hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles, freight containers, and... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY VESSEL General Handling and Stowage § 176.76 Transport... paragraphs (b) through (f) of this section, hazardous materials authorized to be transported by vessel may be...

Integrated risk reduction framework to improve railway hazardous materials transportation safety

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiang, E-mail: liu94@illinois.edu; Saat, M. Rapik, E-mail: mohdsaat@illinois.edu; Barkan, Christopher P.L., E-mail: cbarkan@illinois.edu

2013-09-15

Highlights: • An integrated framework is developed to optimize risk reduction. • A negative binomial regression model is developed to analyze accident-cause-specific railcar derailment probability. • A Pareto-optimality technique is applied to determine the lowest risk given any level of resource. • A multi-attribute decision model is developed to determine the optimal amount of investment for risk reduction. • The models could aid the government and rail industry in developing cost-efficient risk reduction policy and practice. -- Abstract: Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation.

49 CFR 171.1 - Applicability of Hazardous Materials Regulations (HMR) to persons and functions.

Science.gov (United States)

2010-10-01

... $250 for each violation, except the maximum civil penalty is $110,000 if the violation results in death... and functions. Federal hazardous materials transportation law (49 U.S.C. 5101 et seq.) directs the... regulations to persons who transport hazardous materials in commerce. In addition, the law authorizes the...

76 FR 73011 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-11-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Safety Administration (PHMSA), DOT. ACTION: Notice of actions on Special Permit Applications. SUMMARY: In... reissue the Nuclear 173.56(b)(3)(i special permit Security ). originally issued Administration on an...

ENVIRONMENTALLY SOUND DISPOSAL OF RADIOACTIVE MATERIALS AT A RCRA HAZARDOUS WASTE DISPOSAL FACILITY

International Nuclear Information System (INIS)

Romano, Stephen; Welling, Steven; Bell, Simon

2003-01-01

The use of hazardous waste disposal facilities permitted under the Resource Conservation and Recovery Act (''RCRA'') to dispose of low concentration and exempt radioactive materials is a cost-effective option for government and industry waste generators. The hazardous and PCB waste disposal facility operated by US Ecology Idaho, Inc. near Grand View, Idaho provides environmentally sound disposal services to both government and private industry waste generators. The Idaho facility is a major recipient of U.S. Army Corps of Engineers FUSRAP program waste and received permit approval to receive an expanded range of radioactive materials in 2001. The site has disposed of more than 300,000 tons of radioactive materials from the federal government during the past five years. This paper presents the capabilities of the Grand View, Idaho hazardous waste facility to accept radioactive materials, site-specific acceptance criteria and performance assessment, radiological safety and environmental monitoring program information

Hazardous Material Cargo Frustration at Military Aerial Ports of Embarkation

National Research Council Canada - National Science Library

Christensen, Neil E

2006-01-01

Since military units often require critical hazardous materials in an expedited manner, identifying choke points within the supply chain is necessary to improve logistic support to front line forces...

77 FR 22504 - Hazardous Materials; Packages Intended for Transport by Aircraft

Science.gov (United States)

2012-04-16

... Convention on International Civil Aviation--also known as the Chicago Convention. Future inconsistencies with... known as the Chicago Convention. Future inconsistencies with international transport standards may... material release. Releases of hazardous materials can result in explosions or fires, while radioactive...

Hazardous Materials Transportation Act. Hearing before the Subcommittee on Transportation, Tourism, and Hazardous Materials of the Committee on Energy and Commerce, House of Representatives, One Hundredth Congress, First Session, July 30, 1987

Energy Technology Data Exchange (ETDEWEB)

1988-01-01

About 1.5 billion tons of hazardous materials per year are moved in the US by truck, rail, barge, and air. The Hazardous Materials Transportation Act was the first attempt at a comprehensive Federal scheme for regulation. This hearing looks at the Secretary of Transportation's implementation of the statute for oversight and reauthorization responsibilities. Testimony was heard from 16 witnesses, representatives of Chemical Manufacturers Association, the American Trucking Association, the Association of American Railroads, the Department of Transportation, the Environmental Protection Agency, the Environmental Policy Institute, Office of Technology Assessment, Hazardous Materials Advisory Council, National Tank Truck Carriers, Federal Emergency Management Agency, National Paint and Coatings Association, and a representative from Ohio.

78 FR 1119 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2013-01-07

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... lithium cells and batteries that have been adopted into the 2013-2014 International Civil Aviation... edition, when transporting batteries domestically by air. Incorporation by reference of the 2013-2014...

Safety in the Chemical Laboratory: Certifications for Professional Hazardous Materials and Waste Management.

Science.gov (United States)

Fischer, Kenneth E.

1988-01-01

Discusses the need for determining a curriculum to provide qualified hazardous waste personnel. Describes the needed role of colleges and universities and current hazardous materials certification requirements. Lists requirements for 18 professional certifications. (MVL)

Development of an expert system for transportation of hazardous and radioactive materials

International Nuclear Information System (INIS)

Ferrada, J.J.; Michelhaugh, R.D.; Rawl, R.R.

1994-01-01

Under the sponsorship of the US Department of Energy's (DOE's) Transportation Management Division (EM-261), the Transportation Technologies Group at Oak Ridge National Laboratory (ORNL) has designed and developed an expert system prototype application of the hazardous materials transportation regulations. The objective of this task was to provide a proof-of-concept for developing a computerized expert system that will ensure straightforward, consistent, and error-free application of the hazardous materials transportation regulations. The expert system prototype entailed the analysis of what an expert in hazardous materials shipping information could/should do. From the analysis of the different features required for the expert system prototype, it was concluded that the developmental efforts should be directed to a Windows trademark 3.1 hypermedia environment. Hypermedia technology usually works as an interactive software system that gives personal computer users the ability to organize, manage, and present information in a number of formats--text, graphics, sound, and full-motion video

Asymmetric Information in Iranian’s Health Insurance Market: Testing of Adverse Selection and Moral Hazard

Science.gov (United States)

Lotfi, Farhad; Gorji, Hassan Abolghasem; Mahdavi, Ghadir; Hadian, Mohammad

2015-01-01

Background: Asymmetric information is one of the most important issues in insurance market which occurred due to inherent characteristics of one of the agents involved in insurance contracts; hence its management requires designing appropriate policies. This phenomenon can lead to the failure of insurance market via its two consequences, namely, adverse selection and moral hazard. Objective: This study was aimed to evaluate the status of asymmetric information in Iran’s health insurance market with respect to the demand for outpatient services. Materials/sPatients and Methods: This research is a cross sectional study conducted on households living in Iran. The data of the research was extracted from the information on household’s budget survey collected by the Statistical Center of Iran in 2012. In this study, the Generalized Method of Moment model was used and the status of adverse selection and moral hazard was evaluated through calculating the latent health status of individuals in each insurance category. To analyze the data, Excel, Eviews and stata11 software were used. Results: The estimation of parameters of the utility function of the demand for outpatient services (visit, medicine, and Para-clinical services) showed that households were more risk averse in the use of outpatient care than other goods and services. After estimating the health status of households based on their health insurance categories, the results showed that rural-insured people had the best health status and people with supplementary insurance had the worst health status. In addition, the comparison of the conditional distribution of latent health status approved the phenomenon of adverse selection in all insurance groups, with the exception of rural insurance. Moreover, calculation of the elasticity of medical expenses to reimbursement rate confirmed the existence of moral hazard phenomenon. Conclusions: Due to the existence of the phenomena of adverse selection and moral hazard

77 FR 21714 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2012-04-11

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... cells and batteries that have been adopted into the 2013-2014 International Civil Aviation Organization...) to address the air transportation risks posed by lithium cells and batteries. Some of the proposals...

75 FR 1302 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2010-01-11

... of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... transportation of lithium cells and batteries, including lithium cells and batteries packed with or contained in equipment. The proposed changes are intended to enhance safety by ensuring that all lithium batteries are...

Probability analysis of multiple-tank-car release incidents in railway hazardous materials transportation

International Nuclear Information System (INIS)

Liu, Xiang; Saat, Mohd Rapik; Barkan, Christopher P.L.

2014-01-01

Railroads play a key role in the transportation of hazardous materials in North America. Rail transport differs from highway transport in several aspects, an important one being that rail transport involves trains in which many railcars carrying hazardous materials travel together. By contrast to truck accidents, it is possible that a train accident may involve multiple hazardous materials cars derailing and releasing contents with consequently greater potential impact on human health, property and the environment. In this paper, a probabilistic model is developed to estimate the probability distribution of the number of tank cars releasing contents in a train derailment. Principal operational characteristics considered include train length, derailment speed, accident cause, position of the first car derailed, number and placement of tank cars in a train and tank car safety design. The effect of train speed, tank car safety design and tank car positions in a train were evaluated regarding the number of cars that release their contents in a derailment. This research provides insights regarding the circumstances affecting multiple-tank-car release incidents and potential strategies to reduce their occurrences. The model can be incorporated into a larger risk management framework to enable better local, regional and national safety management of hazardous materials transportation by rail

Probability analysis of multiple-tank-car release incidents in railway hazardous materials transportation

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiang, E-mail: liu94@illinois.edu; Saat, Mohd Rapik, E-mail: mohdsaat@illinois.edu; Barkan, Christopher P.L., E-mail: cbarkan@illinois.edu

2014-07-15

Railroads play a key role in the transportation of hazardous materials in North America. Rail transport differs from highway transport in several aspects, an important one being that rail transport involves trains in which many railcars carrying hazardous materials travel together. By contrast to truck accidents, it is possible that a train accident may involve multiple hazardous materials cars derailing and releasing contents with consequently greater potential impact on human health, property and the environment. In this paper, a probabilistic model is developed to estimate the probability distribution of the number of tank cars releasing contents in a train derailment. Principal operational characteristics considered include train length, derailment speed, accident cause, position of the first car derailed, number and placement of tank cars in a train and tank car safety design. The effect of train speed, tank car safety design and tank car positions in a train were evaluated regarding the number of cars that release their contents in a derailment. This research provides insights regarding the circumstances affecting multiple-tank-car release incidents and potential strategies to reduce their occurrences. The model can be incorporated into a larger risk management framework to enable better local, regional and national safety management of hazardous materials transportation by rail.

Preliminary proposed seismic design and evaluation criteria for new and existing underground hazardous materials storage tanks

International Nuclear Information System (INIS)

Kennedy, R.P.

1991-01-01

The document provides a recommended set of deterministic seismic design and evaluation criteria for either new or existing underground hazardous materials storage tanks placed in either the high hazard or moderate hazard usage catagories of UCRL-15910. The criteria given herein are consistent with and follow the same philosophy as those given in UCRL-15910 for the US Department of Energy facilities. This document is intended to supplement and amplify upon Reference 1 for underground hazardous materials storage tanks

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Removal of radioactive and other hazardous material from fluid waste

Science.gov (United States)

Tranter, Troy J [Idaho Falls, ID; Knecht, Dieter A [Idaho Falls, ID; Todd, Terry A [Aberdeen, ID; Burchfield, Larry A [W. Richland, WA; Anshits, Alexander G [Krasnoyarsk, RU; Vereshchagina, Tatiana [Krasnoyarsk, RU; Tretyakov, Alexander A [Zheleznogorsk, RU; Aloy, Albert S [St. Petersburg, RU; Sapozhnikova, Natalia V [St. Petersburg, RU

2006-10-03

Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.

Application of pristine and doped SnO2 nanoparticles as a matrix for agro-hazardous material (organophosphate) detection

Science.gov (United States)

Khan, Naushad; Athar, Taimur; Fouad, H.; Umar, Ahmad; Ansari, Z. A.; Ansari, S. G.

2017-02-01

With an increasing focus on applied research, series of single/composite materials are being investigated for device development to detect several hazardous, dangerous, and toxic molecules. Here, we report a preliminary attempt of an electrochemical sensor fabricated using pristine Ni and Cr-doped nano tin oxide material (SnO2) as a tool to detect agro-hazardous material, i.e. Organophosphate (OP, chlorpyrifos). The nanomaterial was synthesized using the solution method. Nickel and chromium were used as dopant during synthesis. The synthesized material was calcined at 1000 °C and characterized for morphological, structural, and elemental analysis that showed the formation of agglomerated nanosized particles of crystalline nature. Screen-printed films of powder obtained were used as a matrix for working electrodes in a cyclic voltammogram (CV) at various concentrations of organophosphates (0.01 to 100 ppm). The CV curves were obtained before and after the immobilization of acetylcholinesterase (AChE) on the nanomaterial matrix. An interference study was also conducted with hydroquinone to ascertain the selectivity. The preliminary study indicated that such material can be used as suitable matrix for a device that can easily detect OP to a level of 10 ppb and thus contributes to progress in terms of desired device technology for the food and agricultural-industries.

An OSHA based approach to safety analysis for nonradiological hazardous materials

International Nuclear Information System (INIS)

Yurconic, M.

1992-08-01

The PNL method for chemical hazard classification defines major hazards by means of a list of hazardous substances (or chemical groups) with associated trigger quantities. In addition, the functional characteristics of the facility being classified is also be factored into the classification. In this way, installations defined as major hazard will only be those which have the potential for causing very serious incidents both on and off site. Because of the diversity of operations involving chemicals, it may not be possible to restrict major hazard facilities to certain types of operations. However, this hazard classification method recognizes that in the industrial sector major hazards are most commonly associated with activities involving very large quantities of chemicals and inherently energetic processes. These include operations like petrochemical plants, chemical production, LPG storage, explosives manufacturing, and facilities which use chlorine, ammonia, or other highly toxic gases in bulk quantities. The basis for this methodology is derived from concepts used by OSHA in its proposed chemical process safety standard, the Dow Fire and Explosion Index Hazard Classification Guide, and the International Labor Office's program on chemical safety. For the purpose of identifying major hazard facilities, this method uses two sorting criteria, (1) facility function and processes and (2) quantity of substances to identify facilities requiringclassification. Then, a measure of chemical energy potential (material factor) is used to identify high hazard class facilities

Moral Hazard, Adverse Selection and the Optimal Consumption-Leisure Choice under Equilibrium Price Dispersion

Directory of Open Access Journals (Sweden)

Sergey Malakhov

2017-09-01

Full Text Available The analysis of the optimal consumption-leisure choice under equilibrium price dispersion discovers the methodological difference between problems of moral hazard and adverse selection. While the phenomenon of moral hazard represents the individual behavioral reaction on the marginal rate of substitution of leisure for consumption proposed by the insurance policy, the adverse selection can take place on any imperfect market under equilibrium price dispersion and it looks like a market phenomenon of a natural selection between consumers with different income and different propensity to search. The analysis of health insurance where the propensity to search takes the form of the propensity to seek healthcare demonstrates that moral hazard takes place when the insurance policy proposes a suboptimal consumption-leisure choice and the increase in consumption of medical services with the reduction of leisure time represents not an unlimited demand for “free goods” but the simple process of the consumption-leisure optimization. The path of consumerism with consumer-directed plans can solve partly the problem of moral hazard because in order to eliminate moral hazard this trend should come to the re-sale of medical services under health vouchers like it takes place in the life settlement.

Expert systems for the transportation of hazardous and radioactive materials

International Nuclear Information System (INIS)

Luce, C.E.; Clover, J.C.; Ferrada, J.J.

1994-01-01

Under the supervision of the Transportation Technologies Group which is in the Chemical Technology Division at Oak Ridge National Laboratory, an expert system prototype for the transportation and packaging of hazardous and radioactive materials has been designed and developed. The development of the expert system prototype focused on using the combination of hypermedia elements and the Visual Basic trademark programming language. Hypermedia technology uses software that allows the user to interact with the computing environment through many formats: text, graphics, audio, and full-motion video. With the use of hypermedia, a user-friendly prototype has been developed to sort through numerous transportation regulations, thereby leading to the proper packaging for the materials. The expert system performs the analysis of regulations that an expert in shipping information would do; only the expert system performs the work more quickly. Currently, enhancements in a variety of categories are being made to the prototype. These include further expansion of non-radioactive materials, which includes any material that is hazardous but not radioactive; and the addition of full-motion video, which will depict regulations in terms that are easy to understand and which will show examples of how to handle the materials when packaging them

Materials Selection for Aerospace Systems

Science.gov (United States)

Arnold, Steven M.; Cebon, David; Ashby, Mike

2012-01-01

A systematic design-oriented, five-step approach to material selection is described: 1) establishing design requirements, 2) material screening, 3) ranking, 4) researching specific candidates and 5) applying specific cultural constraints to the selection process. At the core of this approach is the definition performance indices (i.e., particular combinations of material properties that embody the performance of a given component) in conjunction with material property charts. These material selection charts, which plot one property against another, are introduced and shown to provide a powerful graphical environment wherein one can apply and analyze quantitative selection criteria, such as those captured in performance indices, and make trade-offs between conflicting objectives. Finding a material with a high value of these indices maximizes the performance of the component. Two specific examples pertaining to aerospace (engine blades and pressure vessels) are examined, both at room temperature and elevated temperature (where time-dependent effects are important) to demonstrate the methodology. The discussion then turns to engineered/hybrid materials and how these can be effectively tailored to fill in holes in the material property space, so as to enable innovation and increases in performance as compared to monolithic materials. Finally, a brief discussion is presented on managing the data needed for materials selection, including collection, analysis, deployment, and maintenance issues.

75 FR 9147 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2010-03-01

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... transport of lithium cells and batteries. PHMSA and FAA will hold a public meeting on March 5, 2010, in... will be attending the Lithium Battery Public Meeting and wait to be escorted to the Conference Center...

49 CFR 171.16 - Detailed hazardous materials incident reports.

Science.gov (United States)

2010-10-01

... containing any hazardous material suffers structural damage to the lading retention system or damage that..., explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other...

Written instructions for the transport of hazardous materials: Accident management instruction sheets

International Nuclear Information System (INIS)

Ridder, K.

1988-01-01

In spite of the regulations and the safety provisions taken, accidents are not entirely avoidable in the transport of hazardous materials. For managing an accident and preventing further hazards after release of dangerous substances, the vehicle drivers must carry with them the accident management instruction sheets, which give instructions on immediate counter measures to be taken by the driver, and on information to be given to the police and the fire brigades. The article in hand discusses the purpose, the contents, and practice-based improvement of this collection of instruction sheets. Particular reference is given to the newly revised version of June 15, 1988 (Verkehrsblatt 1/88) of the 'Directives for setting up accident management instruction sheets - written instructions - for road transport of hazardous materials', as issued by the Federal Ministry of Transport. (orig./HP) [de

78 FR 66326 - Hazardous Materials: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank...

Science.gov (United States)

2013-11-05

...: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank Car Transportation (RRR) AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Advance Notice of... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Parts...

Adverse selection and moral hazard in health insurance

OpenAIRE

Bien, Franck; Alary, David

2006-01-01

In this paper, we want to characterize the optimal health insurance contract with adverse selection and moral hazard. We assume that policyholders differ by the permanent health status loss and choose an unobservable preventive effort in order to reduce the probability of illness which is ex-ante identical. The difference in illness'after-effect modifies policyholders' preventive actions. By the way, they differ in probabilities of illness leading to a situation close to Rothschild and Stigli...

Method and apparatus for the management of hazardous waste material

Science.gov (United States)

Murray, Jr., Holt

1995-01-01

A container for storing hazardous waste material, particularly radioactive waste material, consists of a cylindrical body and lid of precipitation hardened C17510 beryllium-copper alloy, and a channel formed between the mated lid and body for receiving weld filler material of C17200 copper-beryllium alloy. The weld filler material has a precipitation hardening temperature lower than the aging kinetic temperature of the material of the body and lid, whereby the weld filler material is post weld heat treated for obtaining a weld having substantially the same physical, thermal, and electrical characteristics as the material of the body and lid. A mechanical seal assembly is located between an interior shoulder of the body and the bottom of the lid for providing a vacuum seal.

Hazardous Materials Management and Emergency Response training Center needs assessment

International Nuclear Information System (INIS)

McGinnis, K.A.; Bolton, P.A.; Robinson, R.K.

1993-09-01

For the Hanford Site to provide high-quality training using simulated job-site situations to prepare the 4,000 Site workers and 500 emergency responders for known and unknown hazards a Hazardous Materials Management and Emergency Response Training Center is needed. The center will focus on providing classroom lecture as well as hands-on, realistic training. The establishment of the center will create a partnership among the US Department of Energy; its contractors; labor; local, state, and tribal governments; and Xavier and Tulane Universities of Louisiana. This report presents the background, history, need, benefits, and associated costs of the proposed center

Materials selection for cutting tools

International Nuclear Information System (INIS)

Burkhis, Adel M.

2008-01-01

The selection of proper tool steel for a given application is a difficult task. So; the most important selection factors in choosing cutting tool materials are based on their tool material requirements, cutting tool design and service conditions which is mainly considered as functional requirements. The processability requirements concerns in heat treat ability of the material tool. The classification of these tool materials were discussed with their properties requirement and percent of alloying element which is added to give best properties with a little increase in cost that highly appear in comparison of the selection. The cutting tool materials were evaluated based on two cases; The first was in case of rough surface; the high speed steels is the best material and the other was the ceramic material is the highest performance in cutting of soft or high rate of metal removal. (author)

Hazards assessment for the Hazardous Waste Storage Facility

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-04-01

This report documents the hazards assessment for the Hazardous Waste Storage Facility (HWSF) located at the Idaho National Engineering Laboratory. The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding HWSF, the buildings and structures at HWSF, and the processes used at HWSF are described in this report. All nonradiological hazardous materials at the HWSF were identified (radiological hazardous materials are not stored at HWSF) and screened against threshold quantities according to DOE Order 5500.3A guidance. Two of the identified hazardous materials exceeded their specified threshold quantity. This report discusses the potential release scenarios and consequences associated with an accidental release for each of the two identified hazardous materials, lead and mercury. Emergency considerations, such as emergency planning zones, emergency classes, protective actions, and emergency action levels, are also discussed based on the analysis of potential consequences. Evaluation of the potential consequences indicated that the highest emergency class for operational emergencies at the HWSF would be a Site Area Emergency

Natural radioactivity level and radiological hazard assessment of commonly used building material in Xining, China

International Nuclear Information System (INIS)

Shigang Chao; Xinwei Lu; Mengmeng Zhang; Long Pang

2014-01-01

Natural radioactivity of the commonly used building materials in Xining of China was measured using gamma-ray spectrometer system comprising a NaI(Tl) detector. Radioactivity concentrations of 226 Ra, 232 Th and 40 K in the studied samples range from 11.6 to 120.6, 10.2 to 107.1 and 228.0 to 1,036.2 Bq kg -1 , respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the mean value for soil. Radium equivalent activity, indoor air absorbed dose rate, annual effective dose rate as well as external and internal hazard indices were calculated to assess radiological hazards for people living in dwelling made of the building materials. The radiological hazard assessment results show that the studied building materials, except for some aerated concrete block samples, are safe for use in construction of dwellings in the study area and do not pose any significant source of radiation hazard. (author)

Development of a systematic methodology to select hazard analysis techniques for nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

Vasconcelos, Vanderley de; Reis, Sergio Carneiro dos; Costa, Antonio Carlos Lopes da [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mails: vasconv@cdtn.br; reissc@cdtn.br; aclc@cdtn.br; Jordao, Elizabete [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Quimica]. E-mail: bete@feq.unicamp.br

2008-07-01

In order to comply with licensing requirements of regulatory bodies risk assessments of nuclear facilities should be carried out. In Brazil, such assessments are part of the Safety Analysis Reports, required by CNEN (Brazilian Nuclear Energy Commission), and of the Risk Analysis Studies, required by the competent environmental bodies. A risk assessment generally includes the identification of the hazards and accident sequences that can occur, as well as the estimation of the frequencies and effects of these unwanted events on the plant, people, and environment. The hazard identification and analysis are also particularly important when implementing an Integrated Safety, Health, and Environment Management System following ISO 14001, BS 8800 and OHSAS 18001 standards. Among the myriad of tools that help the process of hazard analysis can be highlighted: CCA (Cause- Consequence Analysis); CL (Checklist Analysis); ETA (Event Tree Analysis); FMEA (Failure Mode and Effects Analysis); FMECA (Failure Mode, Effects and Criticality Analysis); FTA (Fault Tree Analysis); HAZOP (Hazard and Operability Study); HRA (Human Reliability Analysis); Pareto Analysis; PHA (Preliminary Hazard Analysis); RR (Relative Ranking); SR (Safety Review); WI (What-If); and WI/CL (What-If/Checklist Analysis). The choice of a particular technique or a combination of techniques depends on many factors like motivation of the analysis, available data, complexity of the process being analyzed, expertise available on hazard analysis, and initial perception of the involved risks. This paper presents a systematic methodology to select the most suitable set of tools to conduct the hazard analysis, taking into account the mentioned involved factors. Considering that non-reactor nuclear facilities are, to a large extent, chemical processing plants, the developed approach can also be applied to analysis of chemical and petrochemical plants. The selected hazard analysis techniques can support cost

Development of a systematic methodology to select hazard analysis techniques for nuclear facilities

International Nuclear Information System (INIS)

Vasconcelos, Vanderley de; Reis, Sergio Carneiro dos; Costa, Antonio Carlos Lopes da; Jordao, Elizabete

2008-01-01

In order to comply with licensing requirements of regulatory bodies risk assessments of nuclear facilities should be carried out. In Brazil, such assessments are part of the Safety Analysis Reports, required by CNEN (Brazilian Nuclear Energy Commission), and of the Risk Analysis Studies, required by the competent environmental bodies. A risk assessment generally includes the identification of the hazards and accident sequences that can occur, as well as the estimation of the frequencies and effects of these unwanted events on the plant, people, and environment. The hazard identification and analysis are also particularly important when implementing an Integrated Safety, Health, and Environment Management System following ISO 14001, BS 8800 and OHSAS 18001 standards. Among the myriad of tools that help the process of hazard analysis can be highlighted: CCA (Cause- Consequence Analysis); CL (Checklist Analysis); ETA (Event Tree Analysis); FMEA (Failure Mode and Effects Analysis); FMECA (Failure Mode, Effects and Criticality Analysis); FTA (Fault Tree Analysis); HAZOP (Hazard and Operability Study); HRA (Human Reliability Analysis); Pareto Analysis; PHA (Preliminary Hazard Analysis); RR (Relative Ranking); SR (Safety Review); WI (What-If); and WI/CL (What-If/Checklist Analysis). The choice of a particular technique or a combination of techniques depends on many factors like motivation of the analysis, available data, complexity of the process being analyzed, expertise available on hazard analysis, and initial perception of the involved risks. This paper presents a systematic methodology to select the most suitable set of tools to conduct the hazard analysis, taking into account the mentioned involved factors. Considering that non-reactor nuclear facilities are, to a large extent, chemical processing plants, the developed approach can also be applied to analysis of chemical and petrochemical plants. The selected hazard analysis techniques can support cost

Hazardous materials emergency response training program at Texas A ampersand M University

International Nuclear Information System (INIS)

Stirling, A.G.

1989-01-01

The Texas Engineering Extension Service (TEEX) as the engineering vocational training arm of the Texas A ampersand M University system has conducted oil-spill, hazardous-material, and related safety training for industry since 1976 and fire suppression training since 1931. In 1987 TEEX conducted training for some 66,000 persons, of which some 6000 were in hazardous-materials safety training and 22,000 in fire suppression or related fields. Various laws and regulations exist relative to employee training at an industrial facility, such as the Hazard Communication Act, the Resource Conservation and Recovery Act (RCRA), the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA or more commonly Superfund), the Community Right to Know Law, and the Superfund Amendments and Reauthorization Act (SARA), Titles I and III. The TEEX programs developed on the foundation emphasize the hands-on approach (60% field exercises) to provide a comprehensive training curriculum resulting in regulatory compliance, an effective emergency response capability, a prepared community, and a safe work environment

Some relevant parameters for assessing fire hazards of combustible mine materials using laboratory scale experiments.

Science.gov (United States)

Litton, Charles D; Perera, Inoka E; Harteis, Samuel P; Teacoach, Kara A; DeRosa, Maria I; Thomas, Richard A; Smith, Alex C

2018-04-15

When combustible materials ignite and burn, the potential for fire growth and flame spread represents an obvious hazard, but during these processes of ignition and flaming, other life hazards present themselves and should be included to ensure an effective overall analysis of the relevant fire hazards. In particular, the gases and smoke produced both during the smoldering stages of fires leading to ignition and during the advanced flaming stages of a developing fire serve to contaminate the surrounding atmosphere, potentially producing elevated levels of toxicity and high levels of smoke obscuration that render the environment untenable. In underground mines, these hazards may be exacerbated by the existing forced ventilation that can carry the gases and smoke to locations far-removed from the fire location. Clearly, materials that require high temperatures (above 1400 K) and that exhibit low mass loss during thermal decomposition, or that require high heat fluxes or heat transfer rates to ignite represent less of a hazard than materials that decompose at low temperatures or ignite at low levels of heat flux. In order to define and quantify some possible parameters that can be used to assess these hazards, small-scale laboratory experiments were conducted in a number of configurations to measure: 1) the toxic gases and smoke produced both during non-flaming and flaming combustion; 2) mass loss rates as a function of temperature to determine ease of thermal decomposition; and 3) mass loss rates and times to ignition as a function of incident heat flux. This paper describes the experiments that were conducted, their results, and the development of a set of parameters that could possibly be used to assess the overall fire hazard of combustible materials using small scale laboratory experiments.

Performance-oriented packagings for hazardous materials: Resource guide

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities.

Performance-oriented packagings for hazardous materials: Resource guide

International Nuclear Information System (INIS)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities

A suggested approach to the selection of chemical and biological protective clothing--meeting industry and emergency response needs for protection against a variety of hazards.

Science.gov (United States)

Stull, Jeffrey O

2004-01-01

The paper describes the development of a comprehensive decision logic for selection and use of biological and chemical protective clothing (BCPC). The decision logic recognizes the separate areas of BCPC use among emergency, biological, and chemical hazards. The proposed decision logic provides a system for type classifying BCPC in terms of its compliance with existing standards (for emergency applications), the overall clothing integrity, and the material barrier performance. Type classification is offered for garments, gloves, footwear, and eye/face protection devices. On the basis of multiple, but simply designed flowcharts, the type of BCPC appropriate for specific biological and chemical hazards can be selected. The decision logic also provides supplemental considerations for choosing appropriate BCPC features.

Risk assessment of major hazards: Hazardous materials transportation in urban areas

Energy Technology Data Exchange (ETDEWEB)

Hubert, Ph; Pages, P

1988-02-01

There is no doubt that, thanks to the pioneering studies of the late seventies and the early eighties, a methodology has been made available that allows risk management of hazardous transportation in urban areas. This approach can easily be extended to the management of other similar risks (storages and to some extent natural hazards). The methodology is both technically available and affordable. The insertion within the decision making processes deserves still some efforts. It has be seen that the applications are broad and numerous. They range from route selection to emergency preparedness, with some insights into acceptability considerations. One limit to the use of such studies, aiming to an objective assessment of the risk, is the complexity of the decision problems, where many factors are to be considered, the most subtle being the one linked to acceptability. However, as such studies develop, those factors start to be clarified, and decision makers learn how to use risk indices in this context. So at the present time it can be said that risk analyses are a valuable input into the decision making process in most cases. And, as more experience is acquired the uses are broader. As any technical innovation risk assessment modifies the approaches to the questions it is dealing with. It seems impossible now to treat those kinds of risks as was done ten years ago.

Risk assessment of major hazards: Hazardous materials transportation in urban areas

International Nuclear Information System (INIS)

Hubert, Ph.; Pages, P.

1988-02-01

There is no doubt that, thanks to the pioneering studies of the late seventies and the early eighties, a methodology has been made available that allows risk management of hazardous transportation in urban areas. This approach can easily be extended to the management of other similar risks (storages and to some extent natural hazards). The methodology is both technically available and affordable. The insertion within the decision making processes deserves still some efforts. It has be seen that the applications are broad and numerous. They range from route selection to emergency preparedness, with some insights into acceptability considerations. One limit to the use of such studies, aiming to an objective assessment of the risk, is the complexity of the decision problems, where many factors are to be considered, the most subtle being the one linked to acceptability. However, as such studies develop, those factors start to be clarified, and decision makers learn how to use risk indices in this context. So at the present time it can be said that risk analyses are a valuable input into the decision making process in most cases. And, as more experience is acquired the uses are broader. As any technical innovation risk assessment modifies the approaches to the questions it is dealing with. It seems impossible now to treat those kinds of risks as was done ten years ago

Developments in consequence modelling of accidental releases of hazardous materials

NARCIS (Netherlands)

Boot, H.

2012-01-01

The modelling of consequences of releases of hazardous materials in the Netherlands has mainly been based on the “Yellow Book”. Although there is no updated version of this official publication, new insights have been developed during the last decades. This article will give an overview of new

Impacts on health and safety from transfer/consolidation of nuclear materials and hazardous chemicals

International Nuclear Information System (INIS)

Gallucci, R.H.V.

1994-11-01

Environmental restoration plans at the US Department of Energy (USDOE) Hanford Site calls for transfer/consolidation of ''targets/threats,'' namely nuclear materials and hazardous chemicals. Reductions in the health and safety hazards will depend on the plans implemented. Pacific Northwest Laboratory (PNL) estimated these potential impacts, assuming implementation of the current reference plan and employing ongoing risk and safety analyses. The results indicated the potential for ''significant'' reductions in health and safety hazards in the long term (> 25 years) and a potentially ''noteworthy'' reduction in health hazard in the short term (≤ 25 years)

Analysis on the Industrial Design of Food Package and the Component of Hazardous Substance in the Packaging Material

OpenAIRE

Wei-Wen Huang

2015-01-01

Transferring the hazardous chemicals contained in food packaging materials into food would threaten the health of consumers, therefore, the related laws and regulations and the detection method of hazardous substance have been established at home and abroad to ensure the safety to use the food packaging material. According to the analysis on the hazardous component in the food packaging, a set of detection methods for hazardous substance in the food packaging was established in the paper and ...

77 FR 36607 - Office of Hazardous Materials Safety Notice of Applications for Modification of Special Permit

Science.gov (United States)

2012-06-19

... modification of special permits (e.g. to provide for additional hazardous materials, packaging design changes... hazardous materials. 12102-M EQ Industrial 49 CFR 173.56(i); To modify the special Services, Inc. 173.56(b... 4.1. 13102-M Robertshaw Industrial 49 CFR 173.150(b); To modify the special Products dba 173.222(c...

A critical review of selective absorbers for radioactive and hazardous species

Energy Technology Data Exchange (ETDEWEB)

Elder, G R; Simpson, K [Bradtec Ltd., Bristol (United Kingdom)

1997-02-01

Selective removal of radioactive and hazardous species has been a fertile research area for several years. However, for commercial application sorbers need to possess satisfactory properties beyond selectivity and these are reviewed. The benefits of selectivity itself need to be set against the limits for liquid discharges and categorization of solid wastes. Two examples are given to illustrate the aspects described. Many current and potential applications of selective adsorbers are to process streams which were not designed for waste management, but consideration of this at the planning stage as now occurs in the nuclear industry can lead to economic benefit. (author). 10 refs, 1 fig., 2 tabs.

A critical review of selective absorbers for radioactive and hazardous species

International Nuclear Information System (INIS)

Elder, G.R.; Simpson, K.

1997-01-01

Selective removal of radioactive and hazardous species has been a fertile research area for several years. However, for commercial application sorbers need to possess satisfactory properties beyond selectivity and these are reviewed. The benefits of selectivity itself need to be set against the limits for liquid discharges and categorization of solid wastes. Two examples are given to illustrate the aspects described. Many current and potential applications of selective adsorbers are to process streams which were not designed for waste management, but consideration of this at the planning stage as now occurs in the nuclear industry can lead to economic benefit. (author). 10 refs, 1 fig., 2 tabs

An integrated risk communication system for the transport of hazardous materials

International Nuclear Information System (INIS)

Minor, J.W. IV; Abkowitz, M.D.

2004-01-01

This paper describes the development and implementation of the prototype of an an internet-based, risk communication system prototype for the transport of hazardous materials. The system was designed with the objectives of: (1) incorporating functionality and features that are useful for meeting a variety of risk communication needs, and (2) demonstrating a high degree of interaction among system components, enabling customisation to meet the specific transport risk communication needs requirements of the host organisation. To demonstrate 'proof of concept', the system is applied to two scenarios: 1) building knowledge and awareness, focusing on how information can be entered, organised and disseminated to the public and other transport stakeholders, and 2) emergency management, utilising the system for securely managing information in responding to a transport incident involving hazardous materials transport incident. The effectiveness of the system in these applications is subsequently discussed. (author)

The transportation of hazardous materials

International Nuclear Information System (INIS)

Hillman, J.C.

1981-04-01

The increasing use of dangerous chemicals and petroleum products by S.A. industry makes it necessary for some form of control to be introduced to regulate the transport of these materials before a major disaster occurs, such as has occurred overseas. This report examines all the aspects that could increase the likelihood of such a disaster occurring, including the preparedness of emergency services. It also recommends the improvements or changes required to minimize this possibility. It is apparent that the training and ability of vehicle drivers are key areas in this respect and they are discussed at length. Forthcoming regulations under the Hazardous Substances Act No. 15 of 1973 are examined and the effects of over-restrictive legislation considered. The report concludes that legislation promulgated gradually to reinforce voluntary industrial practices will ultimately restrict this type of transport to the safety-conscious and competent operator, therefore minimizing the risk as much as possible

Material selection for an aerospace component

OpenAIRE

Jönsson, Gustav

2015-01-01

In the world of today there is a drive for lighter and more effective products for various reasons e.g. reduced environmental impact, higher payload, fuel efficiency etc. There is also an expanding development of new materials for a large number of different applications. This makes it more and more difficult for engineers to make good material selections. This has led to the development of a large amount of material selection methods that require more or less effort to select material. An ef...

Assessment of natural radioactivity and radiological hazards in building materials used in Yan'an, China.

Science.gov (United States)

Lu, Xinwei; Li, Nan; Yang, Guang; Zhao, Caifeng

2013-03-01

The concentration of natural radionuclides in commonly used building materials collected from Yan'an, China, was determined using gamma ray spectroscopy with a NaI(Tl) detector. The activity concentration of ²²⁶Ra, ²³²Th, and ⁴⁰K in the studied building materials ranges from 9.4-73.1, 11.5-86.9, and 258.9-1,055.1 Bq kg⁻¹, respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the world mean values for soil. The radium equivalent activity (Raeq), external hazard index (Hex), internal hazard index (Hin), indoor air absorbed dose rate, and annual effective dose rate due to natural radionuclides in samples were estimated to assess radiological hazards for people living in dwellings made of the studied building materials. The calculated Raeq values of all building materials (75.7-222.1 Bq kg⁻¹) are lower than the limit of 370 Bq kg⁻¹. The values of Hex and Hin are less than unity. The mean values of indoor air absorbed dose rates of all building materials (101.0 ± 14.1-177.0 ± 6.8 nGy h⁻¹) are higher than the world population-weighted average of 84 nGy h⁻¹, while the mean values of annual effective dose range from 0.50 ± 0.07-0.87 ± 0.03 mSv y⁻¹, which are lower than the recommended limit of 1 mSv y⁻¹. It is found that these materials may be used safely as construction materials and do not pose significant radiation hazards to inhabitants.

Recycling of hazardous solid waste material using high-temperature solar process heat

Energy Technology Data Exchange (ETDEWEB)

Schaffner, B.; Meier, A.; Wuillemin, D.; Hoffelner, W.; Steinfeld, A.

2003-03-01

A novel high-temperature solar chemical reactor is proposed for the thermal recycling of hazardous solid waste material using concentrated solar power. A 10 kW solar reactor prototype was designed and tested for the carbothermic reduction of electric arc furnace dusts (EAFD). The reactor was subjected to mean solar flux intensities of 2000 kW/m2 and operated in both batch and continuous mode within the temperature range 1120-1400 K. Extraction of up to 99% and 90% of the Zn originally contained in the EAFD was achieved in the residue for the batch and continuous solar experiments, respectively. The condensed off-gas products consisted mainly of Zn, Pb, and Cl. No ZnO was detected when the O{sub 2} concentration remained below 2 vol.-%. The use of concentrated solar energy as the source of process heat offers the possibility of converting hazardous solid waste material into valuable commodities for processes in closed and sustainable material cycles. (author)

Integrated Life-Cycle Hazardous Material Management: A Logistics Imperative for USAREUR and the 7th Army

National Research Council Canada - National Science Library

Werle, Christopher

2000-01-01

This report examines the benefit to be gained by integrating traditional "pharmacy" business practices in the existing supply system rather than building a parallel system for hazardous material/hazardous waste (HM/HW) management...

75 FR 5258 - Hazardous Materials Transportation; Registration and Fee Assessment Program

Science.gov (United States)

2010-02-02

...) train public sector hazardous materials emergency response employees to respond to accidents and... officers, and 500,000 emergency medical services (EMS) providers. Due to the high turnover rates of... planning grants; A new $4,000,000 grant program for non-profit hazmat employee organizations to train...

Hazard evaluation of The International Fusion Materials Irradiation Facility

Energy Technology Data Exchange (ETDEWEB)

Burgazzi, Luciano [ENEA-Centro Ricerche ' Ezio Clementel' , Advanced Physics Technology Division, Via Martiri di Monte Sole, 4, 40129 Bologna (Italy)]. E-mail: burgazzi@bologna.enea.it

2005-01-15

The International Fusion Materials Irradiation Facility (IFMIF) is aimed to provide an intense neutron source by a high current deuteron linear accelerator and a high-speed lithium flow target, for testing candidate materials for fusion. Liquid lithium is being circulated through a loop and is kept at a temperature above its freezing point. In the frame of the design phase called Key Element technology Phase (KEP), jointly performed by an international team to verify the most important risk factors, safety assessment of the whole plant has been required in order to identify the hazards associated with the plant operation. This paper discusses the safety assessments that were performed and their outcome: Failure Mode and Effect Analysis (FMEA) approach has been adopted in order to accomplish the task. Main conclusions of the study is that, on account of the safety and preventive measures adopted, potential plant related hazards are confined within the IFMIF security boundaries and great care must be exercised to protect workers and site personnel from operating the plant. The analysis has provided as a result a set of Postulated Initiating Events (PIEs), that is off-normal events, that could result in hazardous consequences for the plant, together with the total frequency and the list of component failures which could induce the PIE: this assures the exhaustive list of major initiating events of accident sequences, helpful to the further accident sequence analysis phase. Finally, for each one of the individuated PIEs, the evaluation of the accident evolution, in terms of effects on the plant and relative countermeasures, has allowed to verify that adequate measures are being taken both to prevent the accident occurrence and to cope with the accident consequences, thus assuring the fulfilment of the safety requirements.

On-site transportation and handling of uranium-233 special nuclear material: Preliminary hazards and accident analysis. Final

International Nuclear Information System (INIS)

Solack, T.; West, D.; Ullman, D.; Coppock, G.; Cox, C.

1995-01-01

U-233 Special Nuclear Material (SNM) currently stored at the T-Building Storage Areas A and B must be transported to the SW/R Tritium Complex for repackaging. This SNM is in the form of oxide powder contained in glass jars which in turn are contained in heat sealed double polyethylene bags. These doubled-bagged glass jars have been primarily stored in structural steel casks and birdcages for approximately 20 years. The three casks, eight birdcages, and one pail/pressure vessel will be loaded onto a transport truck and moved over an eight day period. The Preliminary Hazards and Accident Analysis for the on-site transportation and handling of Uranium-233 Special Nuclear Material, documented herein, was performed in accordance with the format and content guidance of DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, dated July 1994, specifically Chapter Three, Hazard and Accident Analysis. The Preliminary Hazards Analysis involved detailed walkdowns of all areas of the U-233 SNM movement route, including the T-Building Storage Area A and B, T-Building truck tunnel, and the roadway route. Extensive discussions were held with operations personnel from the Nuclear Material Control Group, Nuclear Materials Accountability Group, EG and G Mound Security and the Material Handling Systems Transportation Group. Existing documentation related to the on-site transportation of hazardous materials, T-Building and SW/R Tritium Complex SARs, and emergency preparedness/response documentation were also reviewed and analyzed to identify and develop the complete spectrum of energy source hazards

Applying radiological emergency planning experience to hazardous materials emergency planning within the nuclear industry

International Nuclear Information System (INIS)

Foltman, A.; Newsom, D.; Lerner, K.

1988-01-01

The nuclear industry has extensive radiological emergency planning (REP) experience that is directly applicable to hazardous materials emergency planning. Recently, the Feed Materials Production Center near Cincinnati, Ohio, successfully demonstrated such application. The REP experience includes conceptual bases and standards for developing plans that have been tested in hundreds of full-scale exercises. The exercise program itself is also well developed. Systematic consideration of the differences between chemical and radiological hazards shows that relatively minor changes to the REP bases and standards are necessary. Conduct of full-scale, REP-type exercises serves to test the plans, provide training, and engender confidence and credibility

Petroleum and hazardous material releases from industrial facilities associated with Hurricane Katrina.

Science.gov (United States)

Santella, Nicholas; Steinberg, Laura J; Sengul, Hatice

2010-04-01

Hurricane Katrina struck an area dense with industry, causing numerous releases of petroleum and hazardous materials. This study integrates information from a number of sources to describe the frequency, causes, and effects of these releases in order to inform analysis of risk from future hurricanes. Over 200 onshore releases of hazardous chemicals, petroleum, or natural gas were reported. Storm surge was responsible for the majority of petroleum releases and failure of storage tanks was the most common mechanism of release. Of the smaller number of hazardous chemical releases reported, many were associated with flaring from plant startup, shutdown, or process upset. In areas impacted by storm surge, 10% of the facilities within the Risk Management Plan (RMP) and Toxic Release Inventory (TRI) databases and 28% of SIC 1311 facilities experienced accidental releases. In areas subject only to hurricane strength winds, a lower fraction (1% of RMP and TRI and 10% of SIC 1311 facilities) experienced a release while 1% of all facility types reported a release in areas that experienced tropical storm strength winds. Of industrial facilities surveyed, more experienced indirect disruptions such as displacement of workers, loss of electricity and communication systems, and difficulty acquiring supplies and contractors for operations or reconstruction (55%), than experienced releases. To reduce the risk of hazardous material releases and speed the return to normal operations under these difficult conditions, greater attention should be devoted to risk-based facility design and improved prevention and response planning.

Estimating adverse selection and moral hazard effects with hospital invoices data in a government-controlled healthcare system.

Science.gov (United States)

Liu, Xiangping; Nestic, Danijel; Vukina, Tomislav

2012-08-01

We use invoices for hospital services from a regional hospital in Croatia to test for adverse selection and moral hazard. There are three categories of patients: with no supplemental insurance, who bought it, and who are entitled to it for free. Our identification procedure relies on the premise that the difference in the observed medical care consumption between the patients who bought the insurance and those entitled to free insurance is caused by pure selection effect, whereas the difference in healthcare consumption between the group that received the free insurance and the group that has no insurance is due to moral hazard. Results show favorable selection for patients in 20- to 30-year-old cohort and significant moral hazard for all age cohorts. The selection effect reverses its sign in older cohorts explained by the differences in risk aversion across cohorts caused by the timing of transition from socialism to market economy. Copyright © 2011 John Wiley & Sons, Ltd.

Hazardous materials and toxic substances - Status report

International Nuclear Information System (INIS)

Sommerlad, R.E.

1991-01-01

The paper first forecasts what the status of hazardous wastes should be in the year 2028. The author believes all the problems will be solved: no new hazardous wastes will be being generated and the current hazardous waste problems will have been cleared up by common sense engineering. He then describes the current status of waste management of hazardous wastes, the regulatory situation, as well as combustion test programs

Natural radioactivity and associated radiation hazardous of main building materials in Yan'an, China

International Nuclear Information System (INIS)

Li Nan; Lu Xinwei; Yang Guang; Zhao Caifeng

2012-01-01

Background: With the rapidly economic development and urbanization in Yan'an city, more building materials were consumed in building construction. While the natural radioactivity level of building materials from Yan'an is limited in the literatures. Purpose: The main objective of this study is to determine the natural radioactivity level and to analyze the associated radiation hazards of building materials in Yan'an. Methods: The specific activities of natural radionuclides 226 Ra, 232 Th and 40 K in various building materials from Yan'an city were determined using low-background gamma-ray spectrometry, and their radiation hazards were evaluated according to the standard methods. Results: The results show that the specific activities of 226 Ra, 232 Th and 40 K in the building materials are 9.4-73.1, 11.5-86.9 and 258.9-1055.1 Bq/kg, respectively. The activities of 226 Ra and 232 Th, except for sand and gravel aggregate, in all other building materials are higher than the corresponding means of local soil, and the activities of 40 K in hollow brick, red-clay brick, sand and gravel aggregate exceed the means of 40 K in soil. However, the values of internal exposure index, external exposure index and gamma radiation index in all investigated building materials are less than 1. Conclusions: The radiation levels of all analyzed building materials are within the national safety standard, which indicates that all analyzed building materials can be used anywhere and they can't cause radiation hazard to the local residents. (authors)

Eco-Material Selection for Auto Bodies

Energy Technology Data Exchange (ETDEWEB)

Mayyas, Ahmad T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Omar, Mohammed [Masdar Institute of Science & Technology; Hayajneh, Mohammed T. [Jordan University of Science and Technology

2017-09-25

In the last decades, majority of automakers started to include lightweight materials in their vehicles to meet hard environmental regulations and to improve fuel efficiency of their vehicles. As a result, eco-material selection for vehicles emerged as a new discipline under design for environment. This chapter will summarize methods of eco-material selections for automotive applications with more emphasis into auto-bodies. A set of metrics for eco-material selection that takes into account all economic, environmental and social factors will be developed using numerical and qualitative methods. These metrics cover products' environmental impact, functionality and manufacturability, in addition to the economic and societal factors.

Survey of naturally occurring hazardous materials in deep geologic formations: a perspective on the relative hazard of deep burial of nuclear wastes

International Nuclear Information System (INIS)

Tonnessen, K.A.; Cohen, J.J.

1977-01-01

Hazards associated with deep burial of solidified nuclear waste are considered with reference to toxic elements in naturally occurring ore deposits. This problem is put into perspective by relating the hazard of a radioactive waste repository to that of naturally occurring geologic formations. The basis for comparison derives from a consideration of safe drinking water levels. Calculations for relative toxicity of FBR waste and light water reactor (LWR) waste in an underground repository are compared with the relative toxicity indices obtained for average concentration ore deposits. Results indicate that, over time, nuclear waste toxicity decreases to levels below those of naturally occurring hazardous materials

Expert Study to Select Indicators of the Occurence of Emerging Mycotoxin Hazards

NARCIS (Netherlands)

Kandhai, M.C.; Booij, C.J.H.; Fels-Klerx, van der H.J.

2011-01-01

This article describes a Delphi-based expert judgment study aimed at the selection of indicators to identify the occurrence of emerging mycotoxin hazards related to Fusarium spp. in wheat supply chains. A panel of 29 experts from 12 European countries followed a holistic approach to evaluate the

Effect of the selected seismic energy dissipation capacity on the materials quantity for reinforced concrete walls

Directory of Open Access Journals (Sweden)

José Miguel Benjumea Royero

2017-02-01

Full Text Available Context: Regarding their design of reinforced concrete structural walls, the Colombian seismic design building code allows the engineer to select one of the three seismic energy dissipation capacity (ordinary, moderate, and special depending on the seismic hazard of the site. Despite this, it is a common practice to choose the minor requirement for the site because it is thought that selecting a higher requirement will lead to larger structural materials amounts and, therefore, cost increments.  Method: In this work, an analytical study was performed in order to determine the effect of the selected energy dissipation capacity on the quantity of materials and ductility displacement capacity of R/C walls. The study was done for a region with low seismic hazard, mainly because this permitted to explore and compare the use of the three seismic energy dissipations capacities. The effect of different parameters such as the wall total height and thickness, the tributary loaded area, and the minimum volumetric steel ratio were studied. Results: The total amount of steel required for the walls with moderate and special energy dissipation capacity corresponds, on average, to 77% and 89%, respectively, of the quantity required for walls with minimum capacity. Conclusions: it is possible to achieve reductions in the total steel required weight when adopting either moderated or special seismic energy dissipation instead of the minimum capacity.  Additionally, a significant increment in the seismic ductility displacements capacity of the wall was obtained.

Spectrally selective solar energy materials

International Nuclear Information System (INIS)

Sikkens, M.

1981-01-01

The performance and properties of spectrally selective materials are considered and, in particular, the selective absorption of solar radiation by free electrons is discussed, both in a homogeneous material in which these electrons are strongly scattered, and in a composite material consisting of small metal particles in a dielectric host. Such materials can be used as selective absorbers if they are deposited as a thin film onto a metal substrate, the latter providing the required low emittance. This type of selective surfaces is produced by reactive sputtering of Ni in an Ar/CH 4 gas mixture. This method can yield Ni films with a considerable carbon concentration. The carbon concentration can be varied over a wide range by adjusting the partial methane pressure. The associated experimental techniques are discussed. As the carbon concentration increases, the structure of the films changes from a Ni phase in which carbon is dissolved, via an intermediate Ni 3 C phase into an amorphous carbon phase with a high electrical resistivity in which small nickel particles are embedded. Both mechanisms of selective absorption by free electrons are observed and are found to be well described by rather simple models. The best selectivity is obtained at high carbon concentrations where the films consist of nickel particles in carbon. Depending on the film thickness and the substrate material, the solar absorptance varies between 0.78 and 0.90, while the thermal emittance varies between 0.025 and 0.04. Since the films are found to be stable at 400 0 C in vacuum, it appears that these films are good candidates for application in photothermal solar energy conversion at temperature levels around 200 0 C and higher. (Auth.)

Just-in-Time techniques as applied to hazardous materials management

OpenAIRE

Spicer, John S.

1996-01-01

Approved for public release; distribution is unlimited This study investigates the feasibility of integrating JIT techniques in the context of hazardous materials management. This study provides a description of JIT, a description of environmental compliance issues and the outgrowth of related HAZMAT policies, and a broad perspective on strategies for applying JIT to HAZMAT management. http://archive.org/details/justintimetechn00spic Lieutenant Commander, United States Navy

Hazardous Materials Pharmacies - A Vital Component of a Robust P2 Program

International Nuclear Information System (INIS)

McCarter, S.

2006-01-01

Integrating pollution prevention (P2) into the Department of Energy Integrated Safety Management (ISM) - Environmental Management System (EMS) approach, required by DOE Order 450.1, leads to an enhanced ISM program at large and complex installations and facilities. One of the building blocks to integrating P2 into a comprehensive environmental and safety program is the control and tracking of the amounts, types, and flow of hazardous materials used on a facility. Hazardous materials pharmacies (typically called HazMarts) provide a solid approach to resolving this issue through business practice changes that reduce use, avoid excess, and redistribute surplus. If understood from concept to implementation, the HazMart is a powerful tool for reducing pollution at the source, tracking inventory storage, controlling usage and flow, and summarizing data for reporting requirements. Pharmacy options can range from a strict, single control point for all hazardous materials to a virtual system, where the inventory is user controlled and reported over a common system. Designing and implementing HazMarts on large, diverse installations or facilities present a unique set of issues. This is especially true of research and development (R and D) facilities where the chemical use requirements are extensive and often classified. There are often multiple sources of supply; a wide variety of chemical requirements; a mix of containers ranging from small ampoules to large bulk storage tanks; and a wide range of tools used to track hazardous materials, ranging from simple purchase inventories to sophisticated tracking software. Computer systems are often not uniform in capacity, capability, or operating systems, making it difficult to use a server-based unified tracking system software. Each of these issues has a solution or set of solutions tied to fundamental business practices. Each requires an understanding of the problem at hand, which, in turn, requires good communication among all

The Hazardous Material Technician Apprenticeship Program at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Steiner, S.D.

1987-07-01

This document describes an apprenticeship training program for hazardous material technician. This entry-level category is achieved after approximately 216 hours of classroom and on-the-job training. Procedures for evaluating performance include in-class testing, use of on-the-job checks, and the assignment of an apprentice mentor for each trainee

Reduction of Fire Hazard in Materials for Irrigators and Water Collectors in Cooling Towers

Energy Technology Data Exchange (ETDEWEB)

Smirnov, N. V.; Konstantinova, N. I., E-mail: konstantinova-n@inbox.ru [FGBU VNIIPO of EMERCOM of Russia (All-Russian Scientific-research Institute of Fire Protection) (Russian Federation); Gordon, E. P. [Research and Production Center “Kaustik” (Russian Federation); Poedintsev, E. A. [FGBU VNIIPO of EMERCOM of Russia (All-Russian Scientific-research Institute of Fire Protection) (Russian Federation)

2016-09-15

A way of reducing the fire hazard of PVC film used to make cooling-tower irrigators and water collectors is examined. A new generation of fire retardant, nanostructured magnesium hydroxide, is used to impart fire retardant properties. The fabrication technology is optimized with a roller-calendering manufacturing technique, and the permissible ranges of fire hazard indicators for materials in irrigators and water collectors are determined.

A structure for models of hazardous materials with complex behavior

International Nuclear Information System (INIS)

Rodean, H.C.

1991-01-01

Most atmospheric dispersion models used to assess the environmental consequences of accidental releases of hazardous chemicals do not have the capability to simulate the pertinent chemical and physical processes associated with the release of the material and its mixing with the atmosphere. The purpose of this paper is to present a materials sub-model with the flexibility to simulate the chemical and physical behaviour of a variety of materials released into the atmosphere. The model, which is based on thermodynamic equilibrium, incorporates the ideal gas law, temperature-dependent vapor pressure equations, temperature-dependent dissociation reactions, and reactions with atmospheric water vapor. The model equations, written in terms of pressure ratios and dimensionless parameters, are used to construct equilibrium diagrams with temperature and the mass fraction of the material in the mixture as coordinates. The model's versatility is demonstrated by its application to the release of UF 6 and N 2 O 4 , two materials with very different physical and chemical properties. (author)

An examination of the Hazardous Materials Transportation Uniform Safety Act (HMTUSA): A southern perspective

International Nuclear Information System (INIS)

1992-03-01

On November 16,1990, President Bush signed into law the most comprehensive amendments to the Hazardous Materials Transportation Act (HMTA) in 15 years. The Hazardous Materials Transportation Uniform Safety Act of 1990 (HMTUSA) was created by Congress in an effort to strengthen and clarify the HMTA. This paper will discuss the act's provisions as they affect shipments of spent fuel and high-level radioactive materials as well as the impact of those provisions on routing and emergency response issues in the southern region. HMTUSA consists of seven key provisions that affect radioactive materials: clarification of regulatory jurisdiction; highway routing standards; broadened industry registration; safety permits for motor carriers of high risk materials; expanded nuclear transportation requirements; new provisions for emergency response training and planning; and a public process for assessing the feasibility of a federally operated central reporting system and data center. In addition to amending various HMTA provisions, the new HMTUSA act provides appropriations to carry out the specific goals of the legislation. The act authorizes appropriations for the 1991, 1992 and 1993 fiscal years

78 FR 22798 - Hazardous Materials: Revision of Maximum and Minimum Civil Penalties

Science.gov (United States)

2013-04-17

.... 5101 et seq.). Section 5123(a) of that law provides civil penalties for knowing violations of Federal... 107--Guidelines for Civil Penalties * * * * * IV. * * * C. * * * Under the Federal hazmat law, 49 U.S... Maximum and Minimum Civil Penalties AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA...

Skateboard deck materials selection

Science.gov (United States)

Liu, Haoyu; Coote, Tasha; Aiolos; Charlie

2018-03-01

The goal of this project was to identify the ideal material for a skateboard deck under 200 in price, minimizing the weight. The material must have a fracture toughness of 5 MPa/m2, have a minimum lifetime of 10, 000 cycles and must not experience brittle fracture. Both single material and hybrid solutions were explored. When further selecting to minimize weight, woods were found to be the best material. Titanium alloy-wood composites were explored to determine the optimal percentage composition of each material.A sandwich panel hybrid of 50% titanium alloy and 50% wood (Ti-Wood) was found to be the optimum material, performing better than the currently used plywood.

Decision Support for Environmental Management of Industrial Non-Hazardous Secondary Materials: New Analytical Methods Combined with Simulation and Optimization Modeling

Science.gov (United States)

Non-hazardous solid materials from industrial processes, once regarded as waste and disposed in landfills, offer numerous environmental and economic advantages when put to beneficial uses (BUs). Proper management of these industrial non-hazardous secondary materials (INSM) requir...

Conceptual design report, Hazardous Materials Management and Emergency Response (HAMMER) Training Center

Energy Technology Data Exchange (ETDEWEB)

Kelly, K.E. [Westinghouse Hanford Co., Richland, WA (United States)

1994-11-09

For the next 30 years, the main activities at the US Department of Energy (DOE) Hanford Site will involve the management, handling, and cleanup of toxic substances. If the DOE is to meet its high standards of safety, the thousands of workers involved in these activities will need systematic training appropriate to their tasks and the risks associated with these tasks. Furthermore, emergency response for DOE shipments is the primary responsibility of state, tribal, and local governments. A collaborative training initiative with the DOE will strengthen emergency response at the Hanford Site and within the regional communities. Local and international labor has joined the Hazardous Materials Management and Emergency Response (HAMMER) partnership, and will share in the HAMMER Training Center core programs and facilities using their own specialized trainers and training programs. The HAMMER Training Center will provide a centralized regional site dedicated to the training of hazardous material, emergency response, and fire fighting personnel.

Conceptual design report, Hazardous Materials Management and Emergency Response (HAMMER) Training Center

International Nuclear Information System (INIS)

Kelly, K.E.

1994-01-01

For the next 30 years, the main activities at the US Department of Energy (DOE) Hanford Site will involve the management, handling, and cleanup of toxic substances. If the DOE is to meet its high standards of safety, the thousands of workers involved in these activities will need systematic training appropriate to their tasks and the risks associated with these tasks. Furthermore, emergency response for DOE shipments is the primary responsibility of state, tribal, and local governments. A collaborative training initiative with the DOE will strengthen emergency response at the Hanford Site and within the regional communities. Local and international labor has joined the Hazardous Materials Management and Emergency Response (HAMMER) partnership, and will share in the HAMMER Training Center core programs and facilities using their own specialized trainers and training programs. The HAMMER Training Center will provide a centralized regional site dedicated to the training of hazardous material, emergency response, and fire fighting personnel

Notification: Audit of Security Categorization for EPA Systems That Handle Hazardous Material Information

Science.gov (United States)

Project #OA-FY18-0089, January 8, 2018. The OIG plans to begin preliminary research to determine whether the EPA classified the sensitivity of data for systems that handle hazardous waste material information as prescribed by NIST.

Truck shipment risks for assessing hazardous materials - a new paradigm incorporating safety and security

Energy Technology Data Exchange (ETDEWEB)

Greenberg, A.; McSweeney, T.; Allen, J.; Lepofsky, M. [Battelle Memorial Inst., Columbus, OH (United States); Abkowitz, M. [Dept. of Civil Engineering, Vanderbilt Univ., Nashville, TN (United States)

2004-07-01

Recent terrorist events, most notably September 11, 2001, have taught us that transportation risk management must be performed with a different lens to accommodate terrorism scenarios that would have previously been considered unlikely to warrant serious attention. Given these circumstances, a new paradigm is needed for managing the risks associated with highway transport of hazardous materials. In particular, this paradigm must: 1) more explicitly consider security threat and vulnerability, and 2) integrate security considerations into an overall framework for addressing natural and man-made disasters, be they accidental or planned. This paper summarizes the results of a study sponsored by the U.S. Department of Transportation, Federal Motor Carrier Safety Administration for the purpose of exploring how a paradigm might evolve in which both safety and security risks can be evaluated as a systematic, integrated process. The work was directed at developing a methodology for assessing the impacts of hazardous materials safety and security incident consequences when transported by highway. This included consideration of the manner in which these materials could be involved in initiating events as well as potential outcomes under a variety of release conditions. The methodology is subsequently applied to various classes of hazardous materials to establish an economic profile of the impacts that might be expected if a major release were to occur. The paper concludes with a discussion of the findings and implications associated with this effort.

Truck shipment risks for assessing hazardous materials - a new paradigm incorporating safety and security

International Nuclear Information System (INIS)

Greenberg, A.; McSweeney, T.; Allen, J.; Lepofsky, M.; Abkowitz, M.

2004-01-01

Recent terrorist events, most notably September 11, 2001, have taught us that transportation risk management must be performed with a different lens to accommodate terrorism scenarios that would have previously been considered unlikely to warrant serious attention. Given these circumstances, a new paradigm is needed for managing the risks associated with highway transport of hazardous materials. In particular, this paradigm must: 1) more explicitly consider security threat and vulnerability, and 2) integrate security considerations into an overall framework for addressing natural and man-made disasters, be they accidental or planned. This paper summarizes the results of a study sponsored by the U.S. Department of Transportation, Federal Motor Carrier Safety Administration for the purpose of exploring how a paradigm might evolve in which both safety and security risks can be evaluated as a systematic, integrated process. The work was directed at developing a methodology for assessing the impacts of hazardous materials safety and security incident consequences when transported by highway. This included consideration of the manner in which these materials could be involved in initiating events as well as potential outcomes under a variety of release conditions. The methodology is subsequently applied to various classes of hazardous materials to establish an economic profile of the impacts that might be expected if a major release were to occur. The paper concludes with a discussion of the findings and implications associated with this effort

Expert geographical information system for assessing hazardous materials in aquatic environments

International Nuclear Information System (INIS)

Regens, J.L.; White, L.; Wright, J.D.; Rene, A.; Mielke, H.; Bakeer, R.; Belkhouche, B.; Barber, M.

1993-01-01

Hazardous substances, including radionuclides, heavy metals, chlorinated hydrocarbons, and industrial solvents, pose unique challenges in terms of environmental restoration and waste management, especially in aquatic environments. When stored, used or disposed of improperly, hazardous materials including transuranic wastes, high level wastes, low level wastes, greater than class C wastes, mixed wastes or chemical wastes can contaminate an array of environmental receptors ranging from soils, sediments, groundwater to surface water. Depending on the specific hazardous substance and site attributes, environmental restoration and waste management can be a complex, problematic activity. This is particularly true for the major Defense Programs facilities managed by the Department of Energy (DOE). This research cluster consists of two discrete elements. Project Element No. 1 develops and applies GIS-based approaches to decision support for environmental restoration by delineating potential exposures and health risks at the Rocky Flats Plant and profiling contemporary and historical demographic/land use patterns at Sandia National Laboratories. Project Element No. 2 develops ESS software for surface water and ground water contaminants in the Mississippi River Basin

Application of geographical information system in disposal site selection for hazardous wastes.

Science.gov (United States)

Rezaeimahmoudi, Mehdi; Esmaeli, Abdolreza; Gharegozlu, Alireza; Shabanian, Hassan; Rokni, Ladan

2014-01-01

The aim of this study was to provide a scientific method based on Geographical Information System (GIS) regarding all sustainable development measures to locate a proper landfill for disposal of hazardous wastes, especially industrial (radioactive) wastes. Seven effective factors for determining hazardous waste landfill were applied in Qom Province, central Iran. These criteria included water, slope, population centers, roads, fault, protected areas and geology. The Analysis Hierarchical Process (AHP) model based on pair comparison was used. First, the weight of each factor was determined by experts; afterwards each layer of maps entered to ARC GIS and with special weight multiplied together, finally the best suitable site was introduced. The most suitable sites for burial were in northwest and west of Qom Province and eventually five zones were introduced as the sample sites. GIs and AHP model is introduced as the technical, useful and accelerator tool for disposal site selection. Furthermore it is determined that geological factor is the most effective layer for site selection. It is suggested that geological conditions should be considered primarily then other factors are taken into consideration.

Understanding and managing the movements of hazardous material shipments through Texas population centers.

Science.gov (United States)

2009-08-01

Every day almost a million shipments of hazardous materials move safely and securely along our nations transportation system, via any combination of modes. Only a small fraction of total shipments interrupt their planned journey due to an incident...

Application of United States Department of Transportation regulations to hazardous material and waste shipments on the Hanford site

International Nuclear Information System (INIS)

Burnside, M.E.

1992-01-01

All hazardous material and waste transported over roadways open to the public must be in compliance with the U.S. Department of Transportation (DOT) regulations. The DOT states that the hazardous material regulations (HMR) also apply to government-owned, contractor-operated (GOCO) transportation operations over any U.S. Department of Energy (DOE) site roadway where the public has free and unrestricted access. Hazardous material and waste in packages that do not meet DOT regulations must be transported on DOE site roadways in a manner that excludes the public and nonessential workers. At the DOE Richland Field Office (the Hanford Site), hazardous material and waste movements that do not meet DOT requirements are transported over public access roadways during off-peak hours with the roadways barricaded. These movements are accomplished using a transportation plan that involves the DOE, DOE contractors, and private utilities who operate on or near the Hanford Site. This method, which is used at the Hanford Site to comply with DOT regulations onsite, can be communicated to other DOE sites to provide a basis for achieving consistency in similar transportation operations. (author)

Hazardous materials in aquatic environments of the Mississippi River Basin. Quarterly project status report, October 1, 1993--December 31, 1993

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

This quarterly project status report discusses research projects being conducted on hazardous materials in aquatic environments of the Mississippi River basin. We continued to seek improvement in our methods of communication and interactions to support the inter-disciplinary, inter-university collaborators within this program. In addition to the defined collaborative research teams, there is increasing interaction among investigators across projects. Planning for the second year of the project has included the development of our internal request for proposals, and refining the review process for selection of proposals for funding.

An Uncertain Wage Contract Model with Adverse Selection and Moral Hazard

Directory of Open Access Journals (Sweden)

Xiulan Wang

2014-01-01

it can be characterized as an uncertain variable. Moreover, the employee's effort is unobservable to the employer, and the employee can select her effort level to maximize her utility. Thus, an uncertain wage contract model with adverse selection and moral hazard is established to maximize the employer's expected profit. And the model analysis mainly focuses on the equivalent form of the proposed wage contract model and the optimal solution to this form. The optimal solution indicates that both the employee's effort level and the wage increase with the employee's ability. Lastly, a numerical example is given to illustrate the effectiveness of the proposed model.

Tulane/Xavier University Hazardous Materials in Aquatic Environments of the Mississippi River Basin. Quarterly progress report, January 1, 1995--March 31, 1995

International Nuclear Information System (INIS)

1995-01-01

This progress report covers activities for the period January 1 - March 31, 1995 on project concerning 'Hazardous Materials in Aquatic Environments of the Mississippi River Basin.' The following activities are each summarized by bullets denoting significant experiments/findings: biotic and abiotic studies on the biological fate, transport and ecotoxicity of toxic and hazardous waste in the Mississippi River Basin; assessment of mechanisms of metal-induced reproductive toxicity in quatic species as a biomarker of exposure; hazardous wastes in aquatic environments: biological uptake and metabolism studies; ecological sentinels of aquatic contamination in the lower Mississippi River system; bioremediation of selected contaminants in aquatic environments of the Mississippi River Basin; a sensitive rapid on-sit immunoassay for heavy metal contamination; pore-level flow, transport, agglomeration and reaction kinetics of microorganism; biomarkers of exposure and ecotoxicity in the Mississippi River Basin; natural and active chemical remediation of toxic metals, organics and radionuclides in the aquatic environment; expert geographical information systems for assessing hazardous wastes in aquatic environments; enhancement of environmental education; and a number of just initiated projects including fate and transport of contaminants in aquatic environments; photocatalytic remediation; radionuclide fate and modeling from Chernobyl

A multisignal detection of hazardous materials for homeland security

Directory of Open Access Journals (Sweden)

Alamaniotis Miltiadis

2009-01-01

Full Text Available The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario.

A multisignal detection of hazardous materials for homeland security

International Nuclear Information System (INIS)

Alamaniotis, M.; Terrill, S.; Perry, J.; Gao, R.; Tsoukalas, L.; Jevremovic, T.

2009-01-01

The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence) in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s) of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s) of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario. (author)

Disaggregated seismic hazard and the elastic input energy spectrum: An approach to design earthquake selection

Science.gov (United States)

Chapman, Martin Colby

1998-12-01

The design earthquake selection problem is fundamentally probabilistic. Disaggregation of a probabilistic model of the seismic hazard offers a rational and objective approach that can identify the most likely earthquake scenario(s) contributing to hazard. An ensemble of time series can be selected on the basis of the modal earthquakes derived from the disaggregation. This gives a useful time-domain realization of the seismic hazard, to the extent that a single motion parameter captures the important time-domain characteristics. A possible limitation to this approach arises because most currently available motion prediction models for peak ground motion or oscillator response are essentially independent of duration, and modal events derived using the peak motions for the analysis may not represent the optimal characterization of the hazard. The elastic input energy spectrum is an alternative to the elastic response spectrum for these types of analyses. The input energy combines the elements of amplitude and duration into a single parameter description of the ground motion that can be readily incorporated into standard probabilistic seismic hazard analysis methodology. This use of the elastic input energy spectrum is examined. Regression analysis is performed using strong motion data from Western North America and consistent data processing procedures for both the absolute input energy equivalent velocity, (Vsbea), and the elastic pseudo-relative velocity response (PSV) in the frequency range 0.5 to 10 Hz. The results show that the two parameters can be successfully fit with identical functional forms. The dependence of Vsbea and PSV upon (NEHRP) site classification is virtually identical. The variance of Vsbea is uniformly less than that of PSV, indicating that Vsbea can be predicted with slightly less uncertainty as a function of magnitude, distance and site classification. The effects of site class are important at frequencies less than a few Hertz. The regression

Hazardous materials incidents on major highways -- A case study

International Nuclear Information System (INIS)

McElhaney, M.S.

1995-01-01

Personnel from both the public and private sectors have been involved for many years in pre-planning for hazardous materials releases at fixed installations all over the world. As a result of several major petroleum releases during marine transportation, oil companies, private contractors and government agencies have been preparing contingency plans for oil spills and other petroleum product releases in marine settings. Various industry groups have also developed plans for railway and pipeline disasters. These response plans are of varying quality, complexity and usefulness. Organizations such as plant emergency response teams, government agencies, contract response and clean-up crews and fire departments use these plans as a basis for training and resource allocation, hopefully becoming familiar enough with them that the plans are truly useful when product releases occur. Planners and emergency responders to hazardous materials releases must overcome some of the deficiencies which have long stood in the way of efficient and effective response and mitigation efforts. Specifically they must recognize and involve all resources with which they may respond or interact during an incident. This involvement should begin with the planning stages and carry through to training and emergency response and recovery efforts. They must ensure that they adopt and utilize a common command and control system and that all potential resources know this system thoroughly and train together before the incident occurs. It is only through incorporating these two factors that may successfully combat the ever growing number of unwanted product releases occurring in the more difficult realm of transportation

Criticality analysis for hazardous materials transportation; Classificacao da criticidade das rotas do transporte rodoviario de produtos perigosos da BRASKEM

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Katia; Brady, Mariana [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil); Diniz, Americo [BRASKEM S.A., Sao Paulo, SP (Brazil)

2008-07-01

The bad conditions of Brazilians roads drive the companies to be more exigent with the transportation of hazardous materials to avoid accidents or materials releases with actions to contain the releases to community and water sources. To minimize this situation, DNV and BRASKEM developed a methodology for risk analysis called Criticality Analysis for Hazardous Materials Transportation. The objective of this methodology is identifying the most critical points of routes to make actions to avoid accidents. (author)

Hazardous materials transportation. Part 2. Radioactive materials and wastes (citations from the NTIS Data Base). Final report for 1964--March 1978

International Nuclear Information System (INIS)

Reimherr, G.W.

1978-06-01

The bibliography cites studies on the hazards, risks, and uncertainty of transporting radioactive wastes and materials. The design of shipping containers and special labels for identification purposes for transporting fuels and wastes are also cited. Studies are included on legislation dealing with the safety and health of the population and the environmental problems associated with transporting radioactive materials

41 CFR 101-42.1101 - Federal supply classification (FSC) groups and classes which contain hazardous materials.

Science.gov (United States)

2010-07-01

..., building paper, and thermal insulation materials Asbestos cloth which has loose fibers or particles that... shipment. 5965 Headsets, handsets, microphones, and speakers Items containing magnetic material. 5970... hazardous chemicals, solvents. 6625 Electrical and electronic properties measuring and testing instruments...

Advanced Materials Laboratory hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Barnett, B.; Banda, Z.

1995-10-01

The Department of Energy Order 55OO.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the AML. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 23 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets.

New ion selective materials. Application to the selective extraction of caesium

International Nuclear Information System (INIS)

Favre-Reguillon, Alain

1996-01-01

This research thesis addresses the synthesis and assessment of ion selective materials. The first part reports the development of a general method of assessment of ion selective materials. In the second part, the author describes different methods used to insolubilize macro-cycles on hydrophilic polymers. The obtained polyurethanes are synthesised. These hydrophilic polymers display interesting complexing properties and selectivities with respect to cations of alkali metals. Then the author addresses the improvement of selectivity with respect to caesium of ion exchange resorcinol-formaldehyde resins. Different factors affecting selectivity are identified, and the concept of molecular print is used to study the improvement of selectivity. The effect of macro-cyclic structures on phenolic resins with respect to caesium is highlighted [fr

Musculoskeletal symptoms and ergonomic hazards among material handlers in grocery retail industries

Science.gov (United States)

Nasrull Abdol Rahman, Mohd; Zuhaidi, Muhammad Fareez Ahmad

2017-08-01

Grocery retail work can be physically demanding as material handler’s tasks involve manual lifting, lowering, carrying, pushing and pulling loads. The nature of this work puts them at a risk for serious low back pain, shoulder pain and other musculoskeletal injuries. This study was conducted by using two different types of tools which were Nordic Musculoskeletal Questionnaire (NMQ) as a survey and Washington Industrial Safety and Health Act (WISHA) Checklist as a direct observation method. Among 46 males and 14 females material handlers were involved throughout this study. For NMQ, the highest body part trouble in the last 12 months was low back pain (88.3%), followed by upper back (68.3%), neck (55.3%) and shoulder (36.7%). While for WISHA Checklist, most of them experienced hazard level involving awkward posture and high hand force. From the research conducted, musculoskeletal disorders (MSDs) and ergonomic risk factors (ERFs) do related as it showed that musculoskeletal disorders may arise if the workers ignored the safety in ergonomic hazards.

Statistical treatment of hazards result from radioactive material in metal scrap

International Nuclear Information System (INIS)

Salem, E.F.; Rashad, S.M.

2013-01-01

Radioactive sources have a wide range of uses in medicine and industry. Radioactive materials entering the public domain in an uncontrolled manner may creating a serious risk of radiation exposure for workers and the public as well as excessive costs for plant decontamination and waste of product to be borne by the metal industry. This paper describes the major accidents that had happened in the last decades due to radioactive material in metal scrap, provides assessment of associated hazards and lessons learned. This will help Regulatory Authority to introduce measures capable to avoid the recurrence of similar events. The study highlights the situation for metal scrap incidents in Egypt.

The materials selection in ITER and the first materials workshop

International Nuclear Information System (INIS)

Matera, R.; Barabash, V.; Kalinin, G.; Tanaka, S.

1998-01-01

The selection of materials and joining technologies to be used in ITER is a trade-off between multiple and often conflicting requirements derived from the unique features of the fusion environment. Materials selection must encompass a total engineering approach, by considering not only physical and mechanical properties, but also the components' manufacturing, their maintainability and reliability, and, finally, how they can be recycled or disposed of at the end of machine operation

Flow evaluation of the leaching hazardous materials from spent nickel-cadmium batteries discarded in different water surroundings.

Science.gov (United States)

Guo, Xingmei; Song, Yan; Nan, Junmin

2018-02-01

The leaching characteristics of hazardous materials from Ni-Cd batteries immersed in four typical water samples, i.e., water with NaCl, river water, tap water, and deionized water, were investigated to evaluate the potential environmental harm of spent Ni-Cd batteries in the water surroundings. It is shown that four water surroundings all could leach hazardous materials from the Ni-Cd batteries. The water with NaCl concentration of 66.7 mg L -1 had the highest leaching ability, the hazardous materials were leached after only approximately 50 days (average time, with a standard deviation of 4.1), while less than 100 days were needed in the others. An electrochemical corrosion is considered to be the main leaching mechanism leading to battery breakage, while the dissolution-deposition process and the powder route result in the leakage and transference of nickel and cadmium materials from the electrodes. The anions, i.e., SO 4 2- and Cl - , and dissolved oxygen in water were demonstrated to be the vital factors that influence the leaching processes. Thus, it is proposed that spent Ni-Cd batteries must be treated properly to avoid potential danger to the environment.

Recent Developments in C-H Activation for Materials Science in the Center for Selective C-H Activation.

Science.gov (United States)

Zhang, Junxiang; Kang, Lauren J; Parker, Timothy C; Blakey, Simon B; Luscombe, Christine K; Marder, Seth R

2018-04-16

Abstract : Organic electronics is a rapidly growing field driven in large part by the synthesis of ∏-conjugated molecules and polymers. Traditional aryl cross-coupling reactions such as the Stille and Suzuki have been used extensively in the synthesis of ∏-conjugated molecules and polymers, but the synthesis of intermediates necessary for traditional cross-couplings can include multiple steps with toxic and hazardous reagents. Direct arylation through C-H bond activation has the potential to reduce the number of steps and hazards while being more atom-economical. Within the Center for Selective C-H Functionalization (CCHF), we have been developing C-H activation methodology for the synthesis of ∏-conjugated materials of interest, including direct arylation of difficult-to-functionalize electron acceptor intermediates and living polymerization of ∏-conjugated polymers through C-H activation.

Assessment of natural radioactivity and associated radiation hazards in some Cameroonian building materials

International Nuclear Information System (INIS)

Ngachin, M.; Garavaglia, M.; Giovani, C.; Kwato Njock, M.G.; Nourreddine, A.

2007-01-01

The concentration of 238 U, 232 Th and 40 K in 13 building materials obtained from factories and collected in field in Cameroon were investigated by γ-ray spectrometry. The activity ranged from 1.76 to 49.84Bqkg -1 , 0.32 to 147Bqkg -1 and 18 to 1226Bqkg -1 for 238 U, 232 Th and 40 K, respectively. The highest 238 U activity was found in compressed red soil brick type I (49.6+/-0.3Bqkg -1 ) produced by a local manufacturer while the highest 232 Th (139+/-13Bqkg -1 ) and 40 K (1162+/-108Bqkg -1 ) activities were found in gravel collected from an exploitation site in Logbadjeck. The activities are compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra eq , the external hazard index H ex , the indoor absorbed dose rate D-bar in air and the annual effective dose equivalent E-bar were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. All building materials have shown Ra eq (range from 10 to 313Bqkg -1 ) lower than the limit of 370Bqkg -1 set in the Organization for Economic Cooperation and Development [OECD, 1979. Exposure to radiation from the natural radioactivity in building materials. OECD, Paris] report which is equivalent to a γ-dose of 1.5mSvyr -1 . Except for the gravel from Logbadjeck, all the materials examined are acceptable for use as building materials as defined by the OECD criterion

Methodology proposal for matrices selection for hazardous wastes stabilization

International Nuclear Information System (INIS)

Silva, Eliane Magalhaes Pereira da; Vasconcelos, Vanderley de; Jordao, Elizabete

2002-01-01

The issues of environmental pollution by solid waste arised with the onset of the industrial era. Coping with these issues has been even worsen due to the lack of consciousness and planning for a sound waste management. In addition, most of the companies have found it difficult to keep themselves competitive in a global economy due to the lack of information and by not having access to waste management new technologies. On the other hand, solidification/stabilization technologies are usual practices in the nuclear industry. The aim of this paper is to present a proposal to the development of a methodology, for selection of immobilization binders for hazardous waste, based on the available technologies in the nuclear industry. (author)

Processing of hazardous material, or damage treatment method for shallow layer underground storage structure

International Nuclear Information System (INIS)

Ito, Hiroshi; Sakaguchi, Takehiko; Nishioka, Yoshihiro.

1997-01-01

In radioactive waste processing facilities and shallow layer underground structures for processing hazardous materials, sheet piles having freezing pipes at the joint portions are spiked into soils at the periphery of a damaged portion of the shallow layer underground structure for processing or storing hazardous materials. Liquid nitrogen is injected to the freezing pipes to freeze the joint portions of adjacent sheet piles. With such procedures, continuous waterproof walls are formed surrounding the soils at the peripheries of the damaged portion. Further, freezing pipes are disposed in the surrounding soils, and liquid nitrogen is injected to freeze the soils. The frozen soils are removed, and artificial foundation materials are filled in the space except for the peripheries of the damaged portion after the removal thereof, and liquid suspension is filled in the peripheries of the damaged portion, and restoration steps for closing the damaged portion are applied. Then, the peripheries of the damaged portion are buried again. With such procedures, series of treatments for removing contaminated soils and repairing a damaged portion can be conducted efficiently at a low cost. (T.M.)

Selection and Basic Properties of the Buffer Material for High-Level Radioactive Waste Repository in China

Institute of Scientific and Technical Information of China (English)

WEN Zhijian

2008-01-01

Radioactive wastes arising from a wide range of human activities are in many different physical and chemical forms, contaminated with varying radioactivity. Their common features are the potential hazard associated with their radioactivity and the need to manage them in such a way as to protect the human environment. The geological disposal is regarded as the most reasonable and effective way to safely disposing high-level radioactive wastes in the world. The conceptual model of geological disposal in China is based on a multi-barrier system that combines an isolating geological environment with an engineered barrier system. The buffer is one of the main engineered barriers for HLW repository. It is expected to maintain its low water permeability, self-sealing property, radio nuclides adsorption and retardation properties, thermal conductivity, chemical buffering property,canister supporting property, and stress buffering property over a long period of time. Bentonite is selected as the main content of buffer material that can satisfy the above requirements. The Gaomiaozi deposit is selected as the candidate supplier for China's buffer material of high level radioactive waste repository. This paper presents the geological features of the GMZ deposit and basic properties of the GMZ Na-bentonite. It is a super-large deposit with a high content of montmorillonite (about 75%), and GMZ-1, which is Na-bentonite produced from GMZ deposit is selected as the reference material for China's buffer material study.

Environmental resources of selected areas of Hawaii: Geological hazards

Energy Technology Data Exchange (ETDEWEB)

Staub, W.P.; Reed, R.M.

1995-03-01

This report has been prepared to make available and archive the background scientific data and related information collected on geologic hazards during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. The US Department of Energy (DOE) published a notice withdrawing its Notice of Intent to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated. This report presents a review of current information on geologic hazards in the Hawaiian Islands. Interrelationships among these hazards are discussed. Probabilities of occurrence of given geologic hazards are provided in various regions where sufficient geologic or historical data are available. Most of the information contained herein is compiled from recent US Geological Survey (USGS) publications and USGS open-file reports related to this project. This report describes the natural geologic hazards present in the area and does not represent an assessment of environmental impacts. Geologic hazards originate both onshore and offshore. Onshore geologic hazards such as volcanic eruptions, earthquakes, surface rupture, landslides, uplift and subsidence occur mainly on the southern third of the island of Hawaii (hereinafter referred to as Hawaii). Offshore geologic hazards are more widely distributed throughout the Hawaiian Islands. Examples of offshore geologic hazards are submarine landslides, turbidity currents, and seismic sea waves (tsunamis).

40 CFR 260.43 - Legitimate recycling of hazardous secondary materials regulated under § 260.34, § 261.2(a)(2)(ii...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Legitimate recycling of hazardous... (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking Petitions § 260.43 Legitimate recycling of... demonstrate that the recycling is legitimate. Hazardous secondary material that is not legitimately recycled...

Landslide hazard mapping with selected dominant factors: A study case of Penang Island, Malaysia

International Nuclear Information System (INIS)

Tay, Lea Tien; Alkhasawneh, Mutasem Sh.; Ngah, Umi Kalthum; Lateh, Habibah

2015-01-01

Landslide is one of the destructive natural geohazards in Malaysia. In addition to rainfall as triggering factos for landslide in Malaysia, topographical and geological factors play important role in the landslide susceptibility analysis. Conventional topographic factors such as elevation, slope angle, slope aspect, plan curvature and profile curvature have been considered as landslide causative factors in many research works. However, other topographic factors such as diagonal length, surface area, surface roughness and rugosity have not been considered, especially for the research work in landslide hazard analysis in Malaysia. This paper presents landslide hazard mapping using Frequency Ratio (FR) and the study area is Penang Island of Malaysia. Frequency ratio approach is a variant of probabilistic method that is based on the observed relationships between the distribution of landslides and each landslide-causative factor. Landslide hazard map of Penang Island is produced by considering twenty-two (22) landslide causative factors. Among these twenty-two (22) factors, fourteen (14) factors are topographic factors. They are elevation, slope gradient, slope aspect, plan curvature, profile curvature, general curvature, tangential curvature, longitudinal curvature, cross section curvature, total curvature, diagonal length, surface area, surface roughness and rugosity. These topographic factors are extracted from the digital elevation model of Penang Island. The other eight (8) non-topographic factors considered are land cover, vegetation cover, distance from road, distance from stream, distance from fault line, geology, soil texture and rainfall precipitation. After considering all twenty-two factors for landslide hazard mapping, the analysis is repeated with fourteen dominant factors which are selected from the twenty-two factors. Landslide hazard map was segregated into four categories of risks, i.e. Highly hazardous area, Hazardous area, Moderately hazardous area

Landslide hazard mapping with selected dominant factors: A study case of Penang Island, Malaysia

Energy Technology Data Exchange (ETDEWEB)

Tay, Lea Tien; Alkhasawneh, Mutasem Sh.; Ngah, Umi Kalthum [School of Electrical and Electronic Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Lateh, Habibah [School of Distance Education, Universiti Sains Malaysia, 11600 Penang (Malaysia)

2015-05-15

Landslide is one of the destructive natural geohazards in Malaysia. In addition to rainfall as triggering factos for landslide in Malaysia, topographical and geological factors play important role in the landslide susceptibility analysis. Conventional topographic factors such as elevation, slope angle, slope aspect, plan curvature and profile curvature have been considered as landslide causative factors in many research works. However, other topographic factors such as diagonal length, surface area, surface roughness and rugosity have not been considered, especially for the research work in landslide hazard analysis in Malaysia. This paper presents landslide hazard mapping using Frequency Ratio (FR) and the study area is Penang Island of Malaysia. Frequency ratio approach is a variant of probabilistic method that is based on the observed relationships between the distribution of landslides and each landslide-causative factor. Landslide hazard map of Penang Island is produced by considering twenty-two (22) landslide causative factors. Among these twenty-two (22) factors, fourteen (14) factors are topographic factors. They are elevation, slope gradient, slope aspect, plan curvature, profile curvature, general curvature, tangential curvature, longitudinal curvature, cross section curvature, total curvature, diagonal length, surface area, surface roughness and rugosity. These topographic factors are extracted from the digital elevation model of Penang Island. The other eight (8) non-topographic factors considered are land cover, vegetation cover, distance from road, distance from stream, distance from fault line, geology, soil texture and rainfall precipitation. After considering all twenty-two factors for landslide hazard mapping, the analysis is repeated with fourteen dominant factors which are selected from the twenty-two factors. Landslide hazard map was segregated into four categories of risks, i.e. Highly hazardous area, Hazardous area, Moderately hazardous area

Hazardous materials safety and security technology field operational test. Volume II, evaluation final report synthesis

Science.gov (United States)

2004-11-11

The catastrophic events of September 11, 2001 and the ongoing war on terrorism have heightened the level of concern from Federal government officials and the transportation industry regarding the secure transport of hazardous materials (HAZMAT). Secu...

Hazardous materials in aquatic environments of the Mississippi River Basin Project management. Technical quarterly progress report, April 1, 1996--June 30, 1996

Energy Technology Data Exchange (ETDEWEB)

McLachlan, J.; Ide, C.F.; O`Connor, S.

1996-08-01

This quarterly report summarizes accomplishments for the Project examining hazardous materials in aquatic environments of the Mississippi River Basin. Among the many research areas summarized are the following: assessment of mechanisms of metal-induced reproductive toxicity in aquatic species as a biomarker of exposure; hazardous wastes in aquatic environment;ecological sentinels of aquatic contamination in the lower Mississippi River System; remediation of selected contaminants; rapid on-site immunassay for heavy metal contamination; molecular mechanisms of developmental toxicity induced by retinoids and retinoid-like molecules; resuseable synthetic membranes for the removal of aromatic and halogenated organic pollutants from waste water; Effects of steroid receptor activation in neurendocrine cell of the mammalian hypothalamus; modeling and assessment of environmental quality of louisiana bayous and swamps; enhancement of environmental education. The report also contains a summary of publications resulting from this project and an appendix with analytical core protocals and target compounds and metals.

Material Selection for a Manual Winch Rope Drum

OpenAIRE

Moses F. Oduori; Enoch K. Musyoka; Thomas O. Mbuya

2016-01-01

The selection of materials is an essential task in mechanical design processes. This paper sets out to demonstrate the application of analytical decision making during mechanical design and, particularly, in selecting a suitable material for a given application. Equations for the mechanical design of a manual winch rope drum are used to derive quantitative material performance indicators, which are then used in a multiple attribute decision making (MADM) model to rank the candidate materials....

Novel Harmonic Regularization Approach for Variable Selection in Cox’s Proportional Hazards Model

Directory of Open Access Journals (Sweden)

Ge-Jin Chu

2014-01-01

Full Text Available Variable selection is an important issue in regression and a number of variable selection methods have been proposed involving nonconvex penalty functions. In this paper, we investigate a novel harmonic regularization method, which can approximate nonconvex Lq  (1/2select key risk factors in the Cox’s proportional hazards model using microarray gene expression data. The harmonic regularization method can be efficiently solved using our proposed direct path seeking approach, which can produce solutions that closely approximate those for the convex loss function and the nonconvex regularization. Simulation results based on the artificial datasets and four real microarray gene expression datasets, such as real diffuse large B-cell lymphoma (DCBCL, the lung cancer, and the AML datasets, show that the harmonic regularization method can be more accurate for variable selection than existing Lasso series methods.

ARTIFICIAL NEURAL NETWORKS BASED GEARS MATERIAL SELECTION HYBRID INTELLIGENT SYSTEM

Institute of Scientific and Technical Information of China (English)

X.C. Li; W.X. Zhu; G. Chen; D.S. Mei; J. Zhang; K.M. Chen

2003-01-01

An artificial neural networks(ANNs) based gear material selection hybrid intelligent system is established by analyzing the individual advantages and weakness of expert system (ES) and ANNs and the applications in material select of them. The system mainly consists of tow parts: ES and ANNs. By being trained with much data samples,the back propagation (BP) ANN gets the knowledge of gear materials selection, and is able to inference according to user input. The system realizes the complementing of ANNs and ES. Using this system, engineers without materials selection experience can conveniently deal with gear materials selection.

Generalized railway tank car safety design optimization for hazardous materials transport: Addressing the trade-off between transportation efficiency and safety

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Barkan, Christopher P.L.

2011-01-01

North America railways offer safe and generally the most economical means of long distance transport of hazardous materials. Nevertheless, in the event of a train accident releases of these materials can pose substantial risk to human health, property or the environment. The majority of railway shipments of hazardous materials are in tank cars. Improving the safety design of these cars to make them more robust in accidents generally increases their weight thereby reducing their capacity and consequent transportation efficiency. This paper presents a generalized tank car safety design optimization model that addresses this tradeoff. The optimization model enables evaluation of each element of tank car safety design, independently and in combination with one another. We present the optimization model by identifying a set of Pareto-optimal solutions for a baseline tank car design in a bicriteria decision problem. This model provides a quantitative framework for a rational decision-making process involving tank car safety design enhancements to reduce the risk of transporting hazardous materials.

An overview of safety assessment, regulation, and control of hazardous material use at NREL

Science.gov (United States)

Nelson, B. P.; Crandall, R. S.; Moskowitz, P. D.; Fthenakis, V. M.

1992-12-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting an unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present an acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management-appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin.

An overview of safety assessment, regulation, and control of hazardous material use at NREL

International Nuclear Information System (INIS)

Nelson, B.P.; Crandall, R.S.; Moskowitz, P.D.; Fthenakis, V.M.

1992-01-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting in unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin

An overview of safety assessment, regulation, and control of hazardous material use at NREL

International Nuclear Information System (INIS)

Nelson, B.P.; Crandall, R.S.; Moskowitz, P.D.; Fthenakis, V.M.

1992-01-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting an unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present an acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management-appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin

Assessment of natural radioactivity and associated radiation hazards in some Cameroonian building materials

Energy Technology Data Exchange (ETDEWEB)

Ngachin, M. [Center for Atomic, Molecular Physics and Quantum Optics, University of Douala, P.O. Box 8580, Douala (Cameroon) and Abdus Salam International Center for Theoretical Physics, Strada Costiera 11, 34014 Trieste (Italy)]. E-mail: mngachin@yahoo.com; Garavaglia, M. [Regional Agency for Environmental Protection (ARPA), 91 via Tavagnacco, 33100 Udine (Italy); Giovani, C. [Regional Agency for Environmental Protection (ARPA), 91 via Tavagnacco, 33100 Udine (Italy); Kwato Njock, M.G. [Center for Atomic, Molecular Physics and Quantum Optics, University of Douala, P.O. Box 8580, Douala (Cameroon); Nourreddine, A. [Institut Pluridisciplinaire Hubert Curien, UMR7500 CNRS-IN2P3 et Universite Louis Pasteur, 23 Rue du Loess, BP 28, F-67037, Strasbourg Cedex 2 (France)

2007-01-15

The concentration of {sup 238}U, {sup 232}Th and {sup 40}K in 13 building materials obtained from factories and collected in field in Cameroon were investigated by {gamma}-ray spectrometry. The activity ranged from 1.76 to 49.84Bqkg{sup -1}, 0.32 to 147Bqkg{sup -1} and 18 to 1226Bqkg{sup -1} for {sup 238}U, {sup 232}Th and {sup 40}K, respectively. The highest {sup 238}U activity was found in compressed red soil brick type I (49.6+/-0.3Bqkg{sup -1}) produced by a local manufacturer while the highest {sup 232}Th (139+/-13Bqkg{sup -1}) and {sup 40}K (1162+/-108Bqkg{sup -1}) activities were found in gravel collected from an exploitation site in Logbadjeck. The activities are compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra{sub eq}, the external hazard index H{sub ex}, the indoor absorbed dose rate D-bar in air and the annual effective dose equivalent E-bar were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. All building materials have shown Ra{sub eq} (range from 10 to 313Bqkg{sup -1}) lower than the limit of 370Bqkg{sup -1} set in the Organization for Economic Cooperation and Development [OECD, 1979. Exposure to radiation from the natural radioactivity in building materials. OECD, Paris] report which is equivalent to a {gamma}-dose of 1.5mSvyr{sup -1}. Except for the gravel from Logbadjeck, all the materials examined are acceptable for use as building materials as defined by the OECD criterion.

Robust routing for hazardous materials transportation with conditional value-at-risk on time-dependent networks.

Science.gov (United States)

2012-11-01

New methods are proposed for mitigating risk in hazardous materials (hazmat) transportation, based on Conditional : Value-at-Risk (CVaR) measure, on time-dependent vehicular networks. While the CVaR risk measure has been : popularly used in financial...

Electrostatic Properties of Selected Personal Protective Equipment Regarding Explosion Hazard

Directory of Open Access Journals (Sweden)

Marcin Jachowicz

2013-01-01

Full Text Available In industries such as the mining, petrochemistry or power industries, personal protective equipment is often used in explosive atmospheres. What causes the occurrence of explosive hazards is ever-present in the work environment they include, electrostatic phenomena as well as the build-up of electrical charges on the surface of the protective equipment used. This paper presents the results of studies which were aimed at determining the fundamental electrostatic parameters of protective helmets as well as eye and face protection, surface resistance and the voltage of electrostatic fields. Examinations on the typical structure of the above mentioned equipment was conducted including the variable values of ambient humidity, which can occur in the working environment and with the use of various types of materials used to generate a charge. The adopted methods and testing equipment have been presented. Using the current, general requirements regarding the electrostatic properties of materials, the examined helmets and eye protection were assessed for their use in explosive atmospheres.

Management of risk factors in the selection and use of PPE [personal protective equipment] on hazardous waste sites

International Nuclear Information System (INIS)

Kemplin, M.G.

1988-01-01

Industrial hygiene managers working in the hazardous waste area face daily decisions concerning appropriate levels of personal protective equipment (PPE) for hazards expected on various waste site projects. Typical hazards include exposures to toxic dust, chemical vapors, toxic gases, splashes of corrosive or toxic substances, radioactive materials and high noise levels. Managers who are experienced in this area recognize that each item of PPE can represent potential hazards in its own right. For example, full-face respirators typically restrict peripheral vision and can impede proper communications. In high ambient temperature conditions, coated protective suits can represent significant heat stress concerns, etc. Accordingly, this paper reviews health and safety management decision-making in this regard

Expert study to select indicators of the occurrence of emerging mycotoxin hazards.

Science.gov (United States)

Kandhai, M C; Booij, C J H; Van der Fels-Klerx, H J

2011-01-01

This article describes a Delphi-based expert judgment study aimed at the selection of indicators to identify the occurrence of emerging mycotoxin hazards related to Fusarium spp. in wheat supply chains. A panel of 29 experts from 12 European countries followed a holistic approach to evaluate the most important indicators for different chain stages (growth, transport and storage, and processing) and their relative importance. After three e-mailing rounds, the experts reached consensus on the most important indicators for each of the three stages: wheat growth, transport and storage, and processing. For wheat growth, these indicators include: relative humidity/rainfall, crop rotation, temperature, tillage practice, water activity of the kernels, and crop variety/cultivar. For the transport and storage stage, they include water activity in the kernels, relative humidity, ventilation, temperature, storage capacity, and logistics. For wheat processing, indicators include quality data, fraction of the cereal used, water activity in the kernels, quality management and traceability systems, and carryover of contamination. The indicators selected in this study can be used in an identification system for the occurrence of emerging mycotoxin hazards in wheat supply chains. Such a system can be used by risk managers within governmental (related) organizations and/or the food and feed industry in order to react proactively to the occurrence of these emerging mycotoxins. © 2010 Society for Risk Analysis.

First-wall/blanket materials selection for STARFIRE tokamak reactor

International Nuclear Information System (INIS)

Smith, D.L.; Mattas, R.F.; Clemmer, R.G.; Davis, J.W.

1980-01-01

The development of the reference STARFIRE first-wall/blanket design involved numerous trade-offs in the materials selection process for the breeding material, coolant structure, neutron multiplier, and reflector. The major parameters and properties that impact materials selection and design criteria are reviewed

Does the good matter? Evidence on moral hazard and adverse selection from consumer credit market

Czech Academy of Sciences Publication Activity Database

Bičáková, Alena

2007-01-01

Roč. 66, č. 1 (2007), s. 29-65 ISSN 0017-0097 Institutional research plan: CEZ:AV0Z70850503 Keywords : consumer credit * adverse selection * moral hazard Subject RIV: AH - Economics http://giornaledeglieconomisti.unibocconi.it/on-line/Home/Volumes/artCat2007.11.1.10.2.html

Guidelines for applying criteria to designate routes for transporting hazardous materials. Final report

International Nuclear Information System (INIS)

1989-07-01

These guidelines were prepared to assist State and local officials in the analysis of alternate routes to be used by highway vehicles transportating hazardous materials. A methodology for assessing comparative risks of routing alternatives is discussed and demonstrated through a hypothetical example. Mathematical models are provided for situations in which measured local data may not be easily obtained or adequate

Incidents with hazardous radiation sources

International Nuclear Information System (INIS)

Schoenhacker, Stefan

2016-01-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

Analysis of the selected optical parameters of filters protecting against hazardous infrared radiation

OpenAIRE

Gralewicz, Grzegorz; Owczarek, Grzegorz

2016-01-01

The paper analyses the selected optical parameters of protective optic filters used for protection of the eyes against hazardous radiation within the visible (VIS) and near infrared (NIR) spectrum range. The indexes characterizing transmission and reflection of optic radiation incident on the filter are compared. As it follows from the completed analysis, the newly developed interference filters provide more effective blocking of infrared radiation in comparison with the currently used protec...

Hazardous materials in aquatic environments of the Mississippi River Basin. Quarterly project status report, July 1, 1994--September 30, 1994

International Nuclear Information System (INIS)

1994-01-01

This document references information pertaining to the presence of hazardous materials in the Mississippi River Basin. Topics discussed include: The biological fate, transport, and ecotoxicity of toxic and hazardous wastes; biological uptake and metabolism; sentinels of aquatic contamination; bioremediation; microorganisms; biomarkers of exposure and ecotoxicity; expert geographical information systems for assessing hazardous wastes in aquatic environments; and enhancement of environmental education at Tulane and Xavier

Assessment of radiological hazards of naturally occurring radioactive materials in cement industry

International Nuclear Information System (INIS)

Aslam, M.; Gul, R.; Ara, T.; Hussain, M.

2012-01-01

A study on the radiological hazard in Portland cement due to the presence of naturally occurring radioactive materials is being carried out. The Portland cement manufactured in the Islamabad/Rawalpindi region of Pakistan, intermediate products (clinker) and the various raw materials which compose the product have been analysed for 226 Ra, 232 Th and 40 K using a gamma spectrometry system with a N-type high-purity germanium detector of 80 % relative efficiency. From the measured gamma ray spectra, specific activities were determined. The mean values of the total specific activity of 226 Ra, 232 Th and 40 K are 34.2±11.9, 29.1±3.6 and 295.1±66.9 Bq kg -1 , respectively in Portland cement, 28.4±8.7, 11.3±1.7 and 63.1±17.3 Bq kg -1 , respectively in lime stone, 8.2±1.9, 16.2±3.9 and 187.7±53.2 Bq kg -1 , respectively in gypsum, 34.7±13.1, 41.2±6.7 and 187.6±17.2 Bq kg -1 , respectively in clay, 41.1±11.8, 39.3±6.9 and 195.1±29.2 Bq kg -1 , respectively in laterite and 51.1±18.2, 23.2±1.2 and 258.4±15.3 Bq kg -1 , respectively in clinker. The radium equivalent activities (Ra eq ), external hazard index (H ex ), internal hazard index (H in ), absorbed dose rate in air (D) and annual effective dose rate (E eff ) were also determined. The measured activity concentrations for these radio nuclides and radiological indices were compared with the reported national and international data. All these measured values are comparable with the worldwide data reported in UNSCEAR publications. (authors)

Quality criteria for phase change materials selection

International Nuclear Information System (INIS)

Vitorino, Nuno; Abrantes, João C.C.; Frade, Jorge R.

2016-01-01

Highlights: • Selection criteria of phase change materials for representative applications. • Selection criteria based on reliable solutions for latent heat transfer. • Guidelines for the role of geometry and heat transfer mechanisms. • Performance maps based on PCM properties, operating conditions, size and time scales. - Abstract: Selection guidelines are primary criterion for optimization of materials for specific applications in order to meet simultaneous and often conflicting requirements. This is mostly true for technologies and products required to meet the main societal needs, such as energy. In this case, gaps between supply and demand require strategies for energy conversion and storage, including thermal storage mostly based on phase change materials. Latent heat storage is also very versatile for thermal management and thermal control by allowing high storage density within narrow temperature ranges without strict dependence between stored thermal energy and temperature. Thus, this work addressed the main issues of latent heat storage from a materials selection perspective, based on expected requirements of applications in thermal energy storage or thermal regulation. Representative solutions for the kinetics of latent heat charge/discharge were used to derive optimization guidelines for high energy density, high power, response time (from fast response to thermal inertia), etc. The corresponding property relations were presented in graphical forms for a wide variety of prospective phase change materials, and for wide ranges of operating conditions, and accounting for changes in geometry and mechanisms.

Radiant business. Hazards of international, illicit trafficking with nuclear materials

International Nuclear Information System (INIS)

Attali, J.

1996-03-01

Since the Cold War has been terminated, public media increasingly come out with reports about cases of illicit trafficking with nuclear technology and nuclear materials. So far, the potential hazard has not been exploding into the big disaster, but imagine what may happen if uranium or plutonium falls into the hands of terrorists, fanatics, or Mafia-type organisations ? The author has been investigating into this problem on behalf of the Secretary General of the UN. He has been travelling all around the world in pursuit of information and indications, and now presents us with the essential results of his mission, compiled in this explosive report. (orig./HP) [de

Immobilization of hazardous and radioactive waste into glass structures

International Nuclear Information System (INIS)

Wicks, G.G.

1997-01-01

As a result of more than three decades of international research, glass has emerged as the material of choice for immobilization of a wide range of potentially hazardous radioactive and non-radioactive materials. The ability of glass structures to incorporate and then immobilize many different elements into durable, high integrity, waste glass products is a direct function of the unique random network structure of the glassy state. Every major country involved with long-term management of high-level radioactive waste (HLW) has either selected or is considering glass as the matrix of choice for immobilizing and ultimately, disposing of the potentially hazardous, high-level radioactive material. There are many reasons why glass is preferred. Among the most important considerations are the ability of glass structures to accommodate and immobilize the many different types of radionuclides present in HLW, and to produce a product that not only has excellent technical properties, but also possesses good processing features. Good processability allows the glass to be fabricated with relative ease even under difficult remote-handling conditions necessary for vitrification of highly radioactive material. The single most important property of the waste glass produced is its ability to retain hazardous species within the glass structure and this is reflected by its excellent chemical durability and corrosion resistance to a wide range of environmental conditions. In addition to immobilization of HLW glass matrices are also being considered for isolation of many other types of hazardous materials, both radioactive as well as nonradioactive. This includes vitrification of various actinides resulting from clean-up operations and the legacy of the cold war, as well as possible immobilization of weapons grade plutonium resulting from disarmament activities. Other types of wastes being considered for immobilization into glasses include transuranic wastes, mixed wastes, contaminated

Implications of the Differential Toxicological Effects of III-V Ionic and Particulate Materials for Hazard Assessment of Semiconductor Slurries.

Science.gov (United States)

Jiang, Wen; Lin, Sijie; Chang, Chong Hyun; Ji, Zhaoxia; Sun, Bingbing; Wang, Xiang; Li, Ruibin; Pon, Nanetta; Xia, Tian; Nel, André E

2015-12-22

Because of tunable band gaps, high carrier mobility, and low-energy consumption rates, III-V materials are attractive for use in semiconductor wafers. However, these wafers require chemical mechanical planarization (CMP) for polishing, which leads to the generation of large quantities of hazardous waste including particulate and ionic III-V debris. Although the toxic effects of micron-sized III-V materials have been studied in vivo, no comprehensive assessment has been undertaken to elucidate the hazardous effects of submicron particulates and released III-V ionic components. Since III-V materials may contribute disproportionately to the hazard of CMP slurries, we obtained GaP, InP, GaAs, and InAs as micron- (0.2-3 μm) and nanoscale (particles for comparative studies of their cytotoxic potential in macrophage (THP-1) and lung epithelial (BEAS-2B) cell lines. We found that nanosized III-V arsenides, including GaAs and InAs, could induce significantly more cytotoxicity over a 24-72 h observation period. In contrast, GaP and InP particulates of all sizes as well as ionic GaCl3 and InCl3 were substantially less hazardous. The principal mechanism of III-V arsenide nanoparticle toxicity is dissolution and shedding of toxic As(III) and, to a lesser extent, As(V) ions. GaAs dissolves in the cell culture medium as well as in acidifying intracellular compartments, while InAs dissolves (more slowly) inside cells. Chelation of released As by 2,3-dimercapto-1-propanesulfonic acid interfered in GaAs toxicity. Collectively, these results demonstrate that III-V arsenides, GaAs and InAs nanoparticles, contribute in a major way to the toxicity of III-V materials that could appear in slurries. This finding is of importance for considering how to deal with the hazard potential of CMP slurries.

Environmental Resources of Selected Areas of Hawaii: Geological Hazards (DRAFT)

Energy Technology Data Exchange (ETDEWEB)

Staub, W.P.

1994-06-01

This report has been prepared to make available and archive the background scientific data and related information collected on geologic hazards during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. The U.S. Department of Energy (DOE) published a notice in the Federal Register on May 17, 1994 (Fed Regis. 5925638) withdrawing its Notice of Intent (Fed Regis. 575433) of February 14, 1992, to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated This report presents a review of current information on geologic hazards in the Hawaiian Islands. Interrelationships among these hazards are discussed. Probabilities of occurrence of given geologic hazards are provided in various regions where sufficient geologic or historical data are available. Most of the information contained herein is compiled from recent U.S. Geological Survey (USGS) publications and open-file reports. This report describes the natural geologic hazards present in the area and does not represent an assessment of environmental impacts. Geologic hazards originate both onshore and offshore. Onshore geologic hazards such as volcanic eruptions, earthquakes, surface rupture, landslides, uplift, and subsidence occur mainly on the southern third of the island of Hawaii (hereinafter referred to as Hawaii). Offshore geologic hazards are more widely distributed throughout the Hawaiian Islands. Examples of offshore geologic hazards are submarine landslides, turbidity currents, and seismic sea waves (tsunamis). First, overviews of volcanic and earthquake activity, and details of offshore geologic hazards is provided for the Hawaiian Islands. Then, a more detailed discussion of onshore geologic hazards is presented with special emphasis on the southern third of Hawaii and the east rift

Hazardous properties and environmental effects of materials used in solar heating and cooling (SHAC) technologies: interim handbook

Energy Technology Data Exchange (ETDEWEB)

Searcy, J.Q.

1978-12-01

General background informaion related to SHAC systems, how a particular material was chosen for this handbook, and codes and standards are given. Materials are categorized according to their functional use in SHAC systems as follows: (1) heat transfer fluids and fluid treatment chemicals, (2) insulation materials, (3) seals and sealant materials, (4) glazing materials, (5) collector materials, and (6) storage media. The informaion is presented under: general properties, chemical composition, thermal degradation products, and thermoxidative products of some commercial materials; toxic properties and other potential health effects; fire hazard properties; and environmental effects of and disposal methods for SHAC materials. (MHR)

General procedure to characterize hazardous waste contaminated with radionuclides

International Nuclear Information System (INIS)

Vokal, A.; Svoboda, K.; Necasova, M.

2002-04-01

The report is structured as follows: Overview of current status of characterization of hazardous wastes contaminated with radionuclides (HWCTR) in the Czech Republic (Legislative aspects; Categorization of HWCwR; Overview of HWCwR emerging from workplaces handling ionizing radiation sources; Mixed waste management in the Czech Republic); General procedure to characterized wastes of the HWCwR type (Information needed from the waste producer; Waste analysis plan - description of waste treatment facilities, verification of wastes, selection of waste parameters followed, selection of sampling method, selection of test methods, selection of frequency of analyses; Radiation protection plan; Non-destructive methods of verification of waste - radiography/tomography, dosimetric inspection, measuring instrumentation, methods usable for the determination of volume and surface activities of materials; Non-destructive invasive methods - internal pressure measurement and gas analysis, endoscopic examination, visual inspection; Destructive methods - sampling, current equipment at Nuclear Research Institute Rez; Identification of hazardous components in waste - chemical screening of mixed wastes; Assessment of immobilization waste matrices; Assessment of packaging; Safety analyses; QA and QC). (P.A.)

Informing Workers of Chemical Hazards: The OSHA Hazard Communication Standard.

Science.gov (United States)

American Chemical Society, Washington, DC.

Practical information on how to implement a chemical-related safety program is outlined in this publication. Highlights of the federal Occupational Safety and Health Administrations (OSHA) Hazard Communication Standard are presented and explained. These include: (1) hazard communication requirements (consisting of warning labels, material safety…

Probabilistic Approach to Conditional Probability of Release of Hazardous Materials from Railroad Tank Cars during Accidents

Science.gov (United States)

2009-10-13

This paper describes a probabilistic approach to estimate the conditional probability of release of hazardous materials from railroad tank cars during train accidents. Monte Carlo methods are used in developing a probabilistic model to simulate head ...

Selection, development and characterisation of plasma facing materials for ITER

International Nuclear Information System (INIS)

Barabash, V.; Akiba, M.; Ulrickson, M.; Vieider, G.

1996-01-01

The current status of the selection of the armour materials for first wall, limiters and divertor are presented. The candidate armour materials are beryllium, tungsten and carbon base materials (mainly carbon fiber composites). The selection of the references grades from these material classes is discussed and the candidate grades are described. The main reasons for the selection of the reference grades are also discussed. The urgent materials R and D needs for the development of the design are described briefly. (orig.)

Converting environmentally hazardous materials into clean energy using a novel nanostructured photoelectrochemical fuel cell

Energy Technology Data Exchange (ETDEWEB)

Gan, Yong X., E-mail: yong.gan@utoledo.edu [Department of Mechanical, Industrial and Manufacturing Engineering, College of Engineering, University of Toledo, Toledo, OH 43606 (United States); Gan, Bo J. [Ottawa Hills High School, 2532 Evergreen Road, Toledo, OH 43606 (United States); Clark, Evan; Su, Lusheng [Department of Mechanical, Industrial and Manufacturing Engineering, College of Engineering, University of Toledo, Toledo, OH 43606 (United States); Zhang, Lihua [Center for Functional Nanomaterials, Brookhaven National Laboratory, Upton, NY 11973 (United States)

2012-09-15

Highlights: ► A photoelectrochemical fuel cell has been made from TiO{sub 2} nanotubes. ► The fuel cell decomposes environmentally hazardous materials to produce electricity. ► Doping the anode with a transition metal oxide increases the visible light sensitivity. ► Loading the anode with a conducting polymer enhances the visible light absorption. -- Abstract: In this work, a novel photoelectrochemical fuel cell consisting of a titanium dioxide nanotube array photosensitive anode and a platinum cathode was made for decomposing environmentally hazardous materials to produce electricity and clean fuel. Titanium dioxide nanotubes (TiO{sub 2} NTs) were prepared via electrochemical oxidation of pure Ti in an ammonium fluoride and glycerol-containing solution. Scanning electron microscopy was used to analyze the morphology of the nanotubes. The average diameter, wall thickness and length of the as-prepared TiO{sub 2} NTs were determined. The photosensitive anode made from the highly ordered TiO{sub 2} NTs has good photo-catalytic property, as proven by the decomposition tests on urea, ammonia, sodium sulfide and automobile engine coolant under ultraviolet (UV) radiation. To improve the efficiency of the fuel cell, doping the TiO{sub 2} NTs with a transition metal oxide, NiO, was performed and the photosensitivity of the doped anode was tested under visible light irradiation. It is found that the NiO-doped anode is sensitive to visible light. Also found is that polyaniline-doped photosensitive anode can harvest photon energy in the visible light spectrum range much more efficiently than the NiO-doped one. It is concluded that the nanostructured photoelectrochemical fuel cell can generate electricity and clean fuel by decomposing hazardous materials under sunlight.

Offsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1997-01-01

This report documents the emergency preparedness Hazards Assessment for the offsite transportation of hazardous material from the Hanford Site. The assessment is required by the US Department of Energy (DOE) Order 151.1. Offsite transportation accidents are categorized using the DOE system to assist communication within the DOE and assure that appropriate assistance is provided to the people in charge at the scene. The assistance will initially include information about the load and the potential hazards. Local authorities will use the information to protect the public following a transportation accident. This Hazards Assessment will focus on the material being transported from the Hanford Site. Shipments coming to Hanford are the responsibility of the shipper and the carrier and, therefore, are not included in this Hazards Assessment, unless the DOE elects to be the shipper of record

75 FR 63 - Hazardous Materials: Revision to Requirements for the Transportation of Batteries and Battery...

Science.gov (United States)

2010-01-04

... contained in equipment, fuel cell systems must not charge batteries during transport; (3) For transportation... 2137-AE54 Hazardous Materials: Revision to Requirements for the Transportation of Batteries and Battery... batteries and battery-powered devices. This final rule corrects several errors in the January 14, 2009 final...

77 FR 17394 - Hazardous Materials: Approval and Communication Requirements for the Safe Transportation of Air...

Science.gov (United States)

2012-03-26

... seat-belt pretensioner devices to a capacity not greater than fifty (50) percent of the drum's total... transported; transportation operations conducted under a special permit; the potential for broad application... utilized by 31 grantees with no known safety problems. A review of the Hazardous Materials Incident Data...

Selective nanoscale growth of lattice mismatched materials

Science.gov (United States)

Lee, Seung-Chang; Brueck, Steven R. J.

2017-06-20

Exemplary embodiments provide materials and methods of forming high-quality semiconductor devices using lattice-mismatched materials. In one embodiment, a composite film including one or more substantially-single-particle-thick nanoparticle layers can be deposited over a substrate as a nanoscale selective growth mask for epitaxially growing lattice-mismatched materials over the substrate.

Gamma activity as a guide for the building raw materials selection and controlling the environmental hazards

Directory of Open Access Journals (Sweden)

T. Ibrahim

2012-06-01

Full Text Available The spectrometric measurements can provide an alarm for the radiation activity and radioelement concentra-tions. The activity increase over the ambient background can be achieved by well calibrated gamma-spectrometers. In comparison between Wadi El-Dahl and Abu Zawal quarries for building raw materials (feld-spar, the activity concentration of El-Dahl stream sediments are 54.5 and 44.5 Bq/kg for uranium and thorium respectively. While the activity concentration of Abu Zawal rock quarry are 167.03 and 79.77 Bq/kg for uranium and thorium respectively. These activities yielding effective dose rates of 0.63 mSv/y for Wadi El-Dahl stream sediments and 1.48 mSv/y for Abu Zawal rock quarry. In summary, the spectrometric measurements are excellent selective tool to monitoring the environment against the radiation risk. In this aspect, Wadi El-Dahl stream sedi-ment quarry considered as the more suitable for producing feldspar as a raw materials to building industry. In comparison, Abu Zawal rock quarry has a higher effective dose rate exceeds the international permissible limits which is 1 mSv/y. A total of 19 feldspar samples were completely described regarding their general chemical fea-tures by using x-ray fluorescence. From the study all the samples contain high concentration of barium and ru-bidium which can separate using different methods in order to use in different important industry.

Selection and challenges for LFR reactor materials

Energy Technology Data Exchange (ETDEWEB)

Weisenburger, A.; Jianu, A.; Del Giacco, M.; Fetzer, R.; Heinzel, A.; Mueller, G. [Karlsruhe Institute of Technology (KIT), Eggenstein-Leopoldshafen (Germany). Inst. for Pulsed Power and Microwave Technology

2013-07-01

Nuclear energy using Fast GenIV reactors can fulfil future demands concerning CO2 free, base load capability and sustainability. One of the most promising coolants especially due to its high thermal inertia is liquid lead (Pb). Since several years researches all over the world investigate this coolant and its impact on the reactor design and by that on the materials to be selected. The LEADER project, a follow up of ELSY, aims to design a prototypical demonstrator ALFRED and to continue with several design related aspects of the ELFR reactor. For a demonstrator the criteria of material selection are somewhat different to a commercial type like the ELFR. Material selection for ELFR of course considers all the aspects relevant for ALFRED plus the targeted burn up and the expected total dpa related damage especially of the fuel pins. In the past compatibility of structural material (steels like 316L, T91 and 15-15Ti (1.4970)) that can be employed for Pb cooled fast nuclear reactors were investigated in several EU projects like EUROTRANS and worldwide. Solubility of steel alloying elements like Ni, Fe, Cr is the driving force for the reduced corrosion resistance in contact with Pb. In-situ oxidation is the acknowledged measure to protect steels in Pb up to certain temperatures that are material dependent. Based on experiments and the derived temperature limits the average core outlet temperatures of ALFRED and the ELFR are set to 480 C. The most challenging conditions with respect to temperature are at the fuel assembly and the heat exchangers. For both, thin stable oxide scales with negligible reduction in heat transfer are the requested protection method. This presentation will give an overview on the selected materials for ALFRED and ELFR considering, beside pure compatibility, the influence of mechanical interaction like creep and fretting. (orig.)

Auditing hazardous waste incineration

International Nuclear Information System (INIS)

Jayanty, R.K.M.; Allen, J.M.; Sokol, C.K.; von Lehmden, D.J.

1990-01-01

This paper reports that audit standards consisting of volatile and semivoltile organics have been established by the EPA to be provided to federal, state, and local agencies or their contractors for use in performance audits to assess the accuracy of measurement methods used during hazardous waste trial burns. The volatile organic audit standards currently total 29 gaseous organics in 5, 6, 7, 9, and 18-component mixtures at part-per-billion (ppb) levels (1 to 10 000 ppb) in compressed gas cylinders in a balance gas of nitrogen. The semivoltile organic audit standards currently total six organics which are spiked onto XAD-2 cartridges for auditing analysis procedures. Studies of all organic standards have been performed to determine the stability of the compounds and the feasibility of using them as performance audit materials. Results as of July 1987 indicate that all of the selected organic compounds are adequately stabile for use as reliable audit materials. Performance audits have been conducted with the audit materials to assess the accuracy of the measurement methods. To date, 160 performance audits have been initiated with the ppb-level audit gases. The audit results obtained with audit gases during hazardous waste trial burn tests were generally within ±50% of the audit concentrations. A limited number of audit results have been obtained with spiked XAD-2 cartridges, and the results have generally been within ±35% of the audit concentrations

Application of risk assessment techniques to 'major hazard' pipelines

Energy Technology Data Exchange (ETDEWEB)

Cox, R A

1982-12-01

A risk analysis for a hazardous-material pipeline (carrying LPG, ammonia, or high-pressure gas) is presented. The analysis gives results in a form that will assist the decisionmaker in pipeline planning and route selection. The large inventory of hazardous materials in such pipelines means that risks exist even though the accident record of pipeline transportation compares favorably with that for competing modes of transport. Risk analysis techniques - commonly used in the civil aviation, nuclear, and process industries - can be equally well applied to pipelines and can produce results that not only give a measure of the risk but also indicate the principal sources of risk and possible areas for improvement. A number of pipeline risk analyses have demonstrated the viability of the technique and its usefulness as an aid to practical engineering in design, planning, and maintenance/repair phases.

Worker safety for occupations affected by the use, transportation and storage of radioactive and hazardous materials

International Nuclear Information System (INIS)

1994-07-01

A study group under the auspices of the National Conference of State Legislatures (NCSL) Labor Committee and the High-level Radioactive Waste/Hazardous Materials Transportation Task Force examined worker protection and safety programs for occupations affected by the use, transportation and storage of radioactive and hazardous materials. Concern about the risks posed to people who live along spent nuclear fuel transportation routes has led to demands for redundant inspections of the transported spent fuel. It would also be prudent to examine the radiological risk to the inspectors themselves before state of federal regulations are promulgated which require redundant inspections. Other workers may also come close to a spent fuel cask during normal operations. The dose rate to which these inspectors and handlers are exposed is higher than the dose rate to which any other group is exposed during incident-free truck transportation and higher than the dose rate to the drivers when they are in the truck cab. This report consists of miscellaneous papers covering topics related to determining radiation doses to workers involved in the transport of radioactive materials

Report: EPA Provided Quality and Timely Information on Hurricane Katrina Hazardous Material Releases and Debris Management

Science.gov (United States)

Report #2006-P-00023, May 2, 2006. After Hurricane Katrina, EPA was the agency with lead responsibility to prevent, minimize, or mitigate threats to public health and the environment caused by hazardous materials and oil spills in inland zones.

Recovering energy and materials from hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Anon.

2003-12-01

The tannery industry faces growing environmental concerns because of the high hazardous metal content of its process waste. The formation, during the tanning process, of the highly toxic hexavalent chromium precludes the use of conventional thermal incineration processes. Borge Tannery in Norway, which processes 600 cattle hides per day, has solved the problem by using new PyroArc technology. The PyroArc waste processing plant can treat all of the tannery's production wastes, transforming them into useful products such as fuel gas and re-usable metal. The fuel gas consists mainly of carbon monoxide, hydrogen and nitrogen, and has a calorific value of about 4 MJ/Nm{sub 3}. About 65-70% of the energy content of the source material (waste or biomass) is recovered in the gas, and this is used to produce steam and/or electricity in a gas engine with a capacity of 580 kW. A further 20-25% of the initial energy content is recovered as heat or low-pressure steam. The plant is designed to be self-sufficient in energy (1.5 MW) and to meet the tannery's maximum requirements for hot water and steam. (UK)

Methodology for Selecting Initiating Events and Hazards for Consideration in an Extended PSA

International Nuclear Information System (INIS)

Wielenberg, A.; Hage, M.; Loeffler, H.; Alzbutas, R.; Apostol, M.; Bareith, A.; Siklossy, T.; Brac, P.; Burgazzi, L.; Cazzoli, E.; Vitazkova, J.; Cizelj, L.; Prosek, A.; Volkanovski, A.; Hashimoto, K.; Godefroy, F.; Gonzalez, M.; Groudev, P.; Kolar, L.; Kumar, M.; Nitoi, M.; Raimond, E.

2016-01-01

An extended PSA applies to a site of one or several Nuclear Power Plant unit(s) and its environment. It intends to calculate the risk induced by the main sources of radioactivity (reactor core and spent fuel storages) on the site, taking into account all operating states for each main source and all possible relevant accident initiating events (both internal and external) affecting one unit or the whole site. The combination between hazards or initiating events and their impact on a unit or the whole site is a crucial issue for an extended PSA. The report tries to discuss relevant methodologies for this purpose. The report proposes a methodology to select initiating events and hazards for the development of an extended PSA. The proposed methodology for initiating events identification, screening and bounding analysis for an extended PSA consists of four major steps: 1. A comprehensive identification of events and hazards and their respective combinations applicable to the plant and site. Qualitative screening criteria will be applied, 2. The calculation of initial (possibly conservative) frequency claims for events and hazards and their respective combinations applicable to the plant and the site. Quantitative screening criteria will be applied, 3. An impact analysis and bounding assessment for all applicable events and scenarios. Events are either screened out from further more detailed analysis, or are assigned to a bounding event (group), or are retained for detailed analysis, 4. The probabilistic analysis of all retained (bounding) events at the appropriate level of detail. (authors)

Hazards assessment for the Waste Experimental Reduction Facility

International Nuclear Information System (INIS)

Calley, M.B.; Jones, J.L. Jr.

1994-01-01

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high

Hazards assessment for the Waste Experimental Reduction Facility

Energy Technology Data Exchange (ETDEWEB)

Calley, M.B.; Jones, J.L. Jr.

1994-09-19

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high.

ABOUT INDEX EVALUATION OF MATERIAL RESOURCE SUPPLIER SELECTION

OpenAIRE

V. A. Skochinskaya

2008-01-01

The paper analyzes existing methods for evaluation of material resource supplier selection. It shows advantages and shortcomings of the present evaluation systems. The necessity for application of an index evaluation is justified in the paper. The paper contains rating (index) evaluation for material resource supplier selection which is based on the application of quantitative (index) tool instead of an expert (numerical) evaluation. 

Development of Neutron Probes for Characterization of Hazardous Materials in the Sub-surface Medium

International Nuclear Information System (INIS)

Keegan, R.P.; McGrath, C.A.; Lopez, J.C.

2002-01-01

Neutron probes are being developed at the Idaho National Engineering and Environmental Laboratory (INEEL) for the detection, identification and quantification of hazardous materials in the ground. Such materials include plutonium, uranium, americium, chlorine and fluorine. Both a Neutron Gamma (NG) probe and a Prompt Fission Neutron (PFN) probe are being developed. The NG probe is used primarily for nuclide identification and quantification measurements. The PFN is used mostly for the detection and measurement of fissile material, but also for the determination of thermal neutron macroscopic absorption cross sections of the various elements comprising the ground matrix. Calibration of these probes will be carried out at the INEEL using an indoor facility that has been designed for this activity

Seismic hazard maps for earthquake-resistant construction designs

International Nuclear Information System (INIS)

Ohkawa, Izuru

2004-01-01

Based on the idea that seismic phenomena in Japan varying in different localities are to be reflected in designing specific nuclear facilities in specific site, the present research program started to make seismic hazard maps representing geographical distribution of seismic load factors. First, recent research data on historical earthquakes and materials on active faults in Japan have been documented. Differences in character due to different localities are expressed by dynamic load in consideration of specific building properties. Next, hazard evaluation corresponding to seismic-resistance factor is given as response index (spectrum) of an adequately selected building, for example a nuclear power station, with the help of investigation results of statistical analysis. (S. Ohno)

Hazardous waste: cleanup and prevention

Science.gov (United States)

Vandas, Stephen; Cronin, Nancy L.; Farrar, Frank; Serrano, Guillermo Eliezer Ávila; Yajimovich, Oscar Efraín González; Muñoz, Aurora R.; Rivera, María del C.

1996-01-01

Our lifestyles are supported by complex Industrial activities that produce many different chemicals and chemical wastes. The Industries that produce our clothing, cars, medicines, paper, food, fuels, steel, plastics, and electric components use and discard thousands of chemicals every year. At home we may use lawn chemicals, solvents, disinfectants, cleaners, and auto products to Improve our quality of life. A chemical that presents a threat or unreasonable risk to people or the environment Is a hazardous material. When a hazardous material can no longer be used, It becomes a hazardous waste. Hazardous wastes come from a variety of sources, from both present and past activities. Impacts to human health and the environment can result from Improper handling and disposal of hazardous waste.

Pre Conference Hazardous Materials Workshop, West/East Coast Safety Conference, held 3-4 October/31 October - 1 November 1981,

Science.gov (United States)

1981-01-01

COMPATABILITY (2) PPE (3) SOP’s 𔃼 NOTES (1) USERDA ( RADIOACTIVE MATERIALS) (2) CHEMTREC (ALL OTHER HAZARDOUS MATERIALS) 2. NAVY A. NAVY ENVIRONMENTAL HEALTH...NRC Regulations for Packaging of Radioactive Material for Transport and Transportation of Radioactive Material Under Certain Conditions (10 CFR 71) V...NAVY) I DOD Directives/Instructions--- DOD Instruction 4120.14 DOD Water and Air Polution Abatement Policy DOD 4145.19R Series Storage and Material

The environmental and medical geochemistry of potentially hazardous materials produced by disasters

Science.gov (United States)

Plumlee, Geoffrey S.; Morman, Suzette A.; Meeker, G.P.; Hoefen, Todd M.; Hageman, Philip L.; Wolf, Ruth E.

2014-01-01

Many natural or human-caused disasters release potentially hazardous materials (HM) that may pose threats to the environment and health of exposed humans, wildlife, and livestock. This chapter summarizes the environmentally and toxicologically significant physical, mineralogical, and geochemical characteristics of materials produced by a wide variety of recent disasters, such as volcanic eruptions, hurricanes and extreme storms, spills of mining/mineral-processing wastes or coal extraction by-products, and the 2001 attacks on and collapse of the World Trade Center towers. In describing these characteristics, this chapter also illustrates the important roles that geochemists and other earth scientists can play in environmental disaster response and preparedness. In addition to characterizing in detail the physical, chemical, and microbial makeup of HM generated by the disasters, these roles also include (1) identifying and discriminating potential multiple sources of the materials; (2) monitoring, mapping, and modeling dispersal and evolution of the materials in the environment; (3) understanding how the materials are modified by environmental processes; (4) identifying key characteristics and processes that influence the materials' toxicity to exposed humans and ecosystems; (5) estimating shifts away from predisaster environmental baseline conditions; and (6) using geochemical insights learned from past disasters to help estimate, prepare for, and increase societal resilience to the environmental and related health impacts of future disasters.

Radiological and hazardous material characterization report for the south portion of the 313 Building

International Nuclear Information System (INIS)

Harris, R.A.

1995-12-01

The objective of the characterization was to determine the extent of radiological contamination and presence of hazardous materials, to allow the preparation of an accurate cost estimate, and to plan for pre-demolition cleanup work to support building isolation. The scope of services for the project included the following tasks: Records Review and Interviews; Site Reconnaissance; Radiological Survey; and Sampling and Analysis

ABOUT INDEX EVALUATION OF MATERIAL RESOURCE SUPPLIER SELECTION

Directory of Open Access Journals (Sweden)

V. A. Skochinskaya

2008-01-01

Full Text Available The paper analyzes existing methods for evaluation of material resource supplier selection. It shows advantages and shortcomings of the present evaluation systems. The necessity for application of an index evaluation is justified in the paper. The paper contains rating (index evaluation for material resource supplier selection which is based on the application of quantitative (index tool instead of an expert (numerical evaluation. 

Using boolean and fuzzy logic combined with analytic hierarchy process for hazardous waste landfill site selection: A case study from Hormozgan province, Iran

Directory of Open Access Journals (Sweden)

Mahdieh Saadat Foomani

2017-01-01

Full Text Available Hazardous wastes include numerous kinds of discarded chemicals and other wastes generated from industrial, commercial, and institutional activities. These types of waste present immediate or long-term risks to humans, animals, plants, or the environment and therefore require special handling for safe disposal. Landfills that can accept hazardous wastes are excavated or engineered sites where these special types of waste can be disposed of securely. Since landfills are permanent sites, special attention must be afforded in selecting the location. This paper investigated the use of the Boolean theory and Fuzzy logic in combination with Analytic Hierarchy Process (AHP methods by applying GIS and IDRISI software for the selection of a hazardous waste landfill site in the Iranian province of Hormozgan. The best location was determined via the Fuzzy and the Boolean methodologies. By collating the area selected for the hazardous waste landfill, this study found that Fuzzy logic with an AND operator had the best options for this purpose. In the end, the most suitable area for a hazardous waste landfill was about 1.6 km2 which was obtained by employing Fuzzy in combination with AHP and by using an AND operator. In addition, all the fundamental criteria affecting the landfill location were considered.

Selection of materials in nuclear fuel: present and future

International Nuclear Information System (INIS)

Munoz-Reja, C.; Fuentes, L.; Garcia de la Infanta, J. M.; Munoz Sicilia, A.

2013-01-01

One of the main aspects of the nuclear fuel is the selection of materials for the components. The operating conditions of the fuel elements impose a major challenge to materials: high temperature, corrosive aqueous environment, high mechanical properties, long periods of time under these extreme conditions and what is the differentiating factor; the effect of irradiation. The materials are selected to fulfill these severe requirements and also to be able to control and to predict its behavior in the working conditions. Their development, in terms of composition and processing, is based on the continuous follow-up of the operation behavior. Many of these materials are specific of the nuclear industry, such as the uranium dioxide and the zirconium alloys. This article presents the selection and development of the nuclear fuel materials as a function of the services requirements. It also includes a view of the new nuclear fuels materials that are being raised after Fukushima accident. (Author)

Probabilistic seismic hazard assessment. Gentilly 2

International Nuclear Information System (INIS)

1996-03-01

Results of this probabilistic seismic hazard assessment were determined using a suite of conservative assumptions. The intent of this study was to perform a limited hazard assessment that incorporated a range of technically defensible input parameters. To best achieve this goal, input selected for the hazard assessment tended to be conservative with respect to selection of attenuation modes, and seismicity parameters. Seismic hazard estimates at Gentilly 2 were most affected by selection of the attenuation model. Alternative definitions of seismic source zones had a relatively small impact on seismic hazard. A St. Lawrence Rift model including a maximum magnitude of 7.2 m b in the zone containing the site had little effect on the hazard estimate relative to other seismic source zonation models. Mean annual probabilities of exceeding the design peak ground acceleration, and the design response spectrum for the Gentilly 2 site were computed to lie in the range of 0.001 to 0.0001. This hazard result falls well within the range determined to be acceptable for nuclear reactor sites located throughout the eastern United States. (author) 34 refs., 6 tabs., 28 figs

Selective Integration in the Material-Point Method

DEFF Research Database (Denmark)

Andersen, Lars; Andersen, Søren; Damkilde, Lars

2009-01-01

The paper deals with stress integration in the material-point method. In order to avoid parasitic shear in bending, a formulation is proposed, based on selective integration in the background grid that is used to solve the governing equations. The suggested integration scheme is compared...... to a traditional material-point-method computation in which the stresses are evaluated at the material points. The deformation of a cantilever beam is analysed, assuming elastic or elastoplastic material behaviour....

Handbook of hazardous waste management

International Nuclear Information System (INIS)

Metry, A.A.

1980-01-01

The contents of this work are arranged so as to give the reader a detailed understanding of the elements of hazardous waste management. Generalized management concepts are covered in Chapters 1 through 5 which are entitled: Introduction, Regulations Affecting Hazardous Waste Management, Comprehensive Hazardous Waste Management, Control of Hazardous Waste Transportation, and Emergency Hazardous Waste Management. Chapters 6 through 11 deal with treatment concepts and are entitled: General Considerations for Hazardous Waste Management Facilities, Physical Treatment of Hazardous Wastes, Chemical Treatment of Hazardous Wastes, Biological Treatment of Hazardous Wastes, Incineration of Hazardous Wastes, and Hazardous Waste Management of Selected Industries. Chapters 12 through 15 are devoted to ultimate disposal concepts and are entitled: Land Disposal Facilities, Ocean Dumping of Hazardous Wastes, Disposal of Extremely Hazardous Wastes, and Generalized Criteria for Hazardous Waste Management Facilities

Guidelines for the Development of Instructional Materials Selection Policies. Handbook I.

Science.gov (United States)

Motomatsu, Nancy, Ed.

This manual was developed to assist school district personnel in the development of policies and procedures for selecting instructional materials. The manual describes State of Washington laws and regulations that govern the selection, use, and disposal of instructional materials and presents criteria and guidelines for selecting materials. Also…

Photovoltaic module encapsulation design and materials selection, volume 1

Science.gov (United States)

Cuddihy, E.; Carroll, W.; Coulbert, C.; Gupta, A.; Liang, R. H.

1982-01-01

Encapsulation material system requirements, material selection criteria, and the status and properties of encapsulation materials and processes available are presented. Technical and economic goals established for photovoltaic modules and encapsulation systems and their status are described. Available encapsulation technology and data are presented to facilitate design and material selection for silicon flat plate photovoltaic modules, using the best materials available and processes optimized for specific power applications and geographic sites. The operational and environmental loads that encapsulation system functional requirements and candidate design concepts and materials that are identified to have the best potential to meet the cost and performance goals for the flat plate solar array project are described. Available data on encapsulant material properties, fabrication processing, and module life and durability characteristics are presented.

Synthesis and characterization of some inorganic ion exchange materials and its application in the treatment of hazardous waste

International Nuclear Information System (INIS)

El-Deeb, A.B.I.M.

2008-01-01

inorganic ion exchange materials play an important role in the last decays in the fields of industry, medicine, agriculture and nuclear technology due to their stabilities towards thermal and radiation and their resistance to chemical attack. the most important property of inorganic ion exchangers enabling their use in the various chemical separation is the selectivity. the selectivity behaviour of synthetic inorganic ion exchanges are still far from being clearly understood. this work had been done in an attempt to synthesize of inorganic ion exchangers such as zircon-titanate and doping alkali metals with zircon-titanate to produce a new developed ion exchanger with properties allow to used in the treatment of hazardous wastes. this work is concerned with the preparation of zircon-titanate and the doping of some alkali metals (K,Na,Li and Cs)with zircon-titanate. characterization of the synthesized ion exchangers using x-ray diffraction, x-ray fluorescence, infrared spectroscopy, surface area and thermal analysis were conducted. equilibrium measurements and effect of batch factor, ph of the medium on percent uptake were determined. capacity measurements and sorption isotherm studies were also investigated on zircon-titanate and its dopant products.

75 FR 45195 - Office of Hazardous Materials Safety; Notice of Applications for Modification of Special Permit

Science.gov (United States)

2010-08-02

... permits (e.g. to provide for additional hazardous materials, packaging design changes, additional mode of... compressed oxygen without rigid outer packaging when no other means of transportation exist. 14860-M Alaska... authorizing the transportation in commerce of compressed oxygen without rigid outer packaging when no other...

Assessment of natural radioactivity and radiological hazards in building materials used in the Tiruvannamalai District, Tamilnadu, India, using a statistical approach

Directory of Open Access Journals (Sweden)

Y. Raghu

2017-07-01

Full Text Available One-hundred-fifty-one samples of six types of building materials were collected from different locations of the Tiruvannamalai District, Tamilnadu, and were analyzed using a gamma ray spectroscopy system. From the results, the highest values observed in the specific activities of 226Ra, 232Th and 40K were 116.1 (soil 106.67 (sand and 527.533 (tiles in Bq kg−1, while the lowest values observed in the specific activities of the same radionuclides were 35.73, 37.75 and 159.83 for cement in Bq kg−1, respectively. The potential radiological hazards were assessed by calculating the radium equivalent activity (Raeq, the indoor absorbed gamma dose rate (DR, the annual effective dose rate (HR, the activity utilization index (I, the alpha index (Iα, the gamma index (Iγ, and the external hazard (Hex and internal hazard (Hin indices. The estimated mean value of the absorbed dose rate of 148.35 nGy h−1 is slightly higher than the world average value of 84 nGy h−1, and the annual effective dose in the studied samples is 0.1824 mSv y−1, which is lower than the recommended limit. Multivariate statistical methods are applied to determine the existing relationship between radionuclides and radiological health hazard parameters and to identify the maximum contribution of radionuclide in radioactivity. The values of the hazard indices were below the recommended levels; therefore, it is concluded that the buildings constructed from such materials are safe for the inhabitants. The findings from this research will be useful to assess the radiation hazards of building materials in humans.

Application of GRA for Sustainable Material Selection and Evaluation Using LCA

Science.gov (United States)

Jayakrishna, Kandasamy; Vinodh, Sekar; Sakthi Sanghvi, Vijayaselvan; Deepika, Chinadurai

2016-07-01

Material selection is identified as a successful key parameter in establishing any product to be sustainable, considering its end of life (EoL) characteristics. An accurate understanding of expected service conditions and environmental considerations are crucial in the selection of material plays a vital role with overwhelming customer expectations and stringent laws. Therefore, this article presents an integrated approach for sustainable material selection using grey relational analysis (GRA) considering the EoL disposal strategies with respect to an automotive product. GRA, an impact evaluation model measures the degree of similarity between the comparability (choice of material) sequence and reference (EoL strategies) sequence based on the relational grade. The ranking result shows that the outranking relationships in the order, ABS-REC > PP-INC > AL-REM > PP-LND > ABS-LND > ABS-INC > PU-LND > AL-REC > AL-LND > PU-INC > AL-INC. The best sustainable material selected was ABS and recycling was selected as the best EoL strategy with the grey relational value of 2.43856. The best material selected by this approach, ABS was evaluated for its viability using life cycle assessment and the estimated impacts also proved the practicability of the selected material highlighting the focus on dehumidification step in the manufacturing of the case product using this developed multi-criteria approach.

Selection of views to materialize using simulated annealing algorithms

Science.gov (United States)

Zhou, Lijuan; Liu, Chi; Wang, Hongfeng; Liu, Daixin

2002-03-01

A data warehouse contains lots of materialized views over the data provided by the distributed heterogeneous databases for the purpose of efficiently implementing decision-support or OLAP queries. It is important to select the right view to materialize that answer a given set of queries. The goal is the minimization of the combination of the query evaluation and view maintenance costs. In this paper, we have addressed and designed algorithms for selecting a set of views to be materialized so that the sum of processing a set of queries and maintaining the materialized views is minimized. We develop an approach using simulated annealing algorithms to solve it. First, we explore simulated annealing algorithms to optimize the selection of materialized views. Then we use experiments to demonstrate our approach. The results show that our algorithm works better. We implemented our algorithms and a performance study of the algorithms shows that the proposed algorithm gives an optimal solution.

Material and process selection using product examples

DEFF Research Database (Denmark)

Lenau, Torben Anker

2001-01-01

The objective of the paper is to suggest a different procedure for selecting materials and processes within the product development work. The procedure includes using product examples in order to increase the number of alternative materials and processes that is considered. Product examples can c...... a search engine, and through hyperlinks can relevant materials and processes be explored. Realising that designers are very sensitive to user interfaces do all descriptions of materials, processes and products include graphical descriptions, i.e. pictures or computer graphics....

Material and process selection using product examples

DEFF Research Database (Denmark)

Lenau, Torben Anker

2002-01-01

The objective of the paper is to suggest a different procedure for selecting materials and processes within the product development work. The procedure includes using product examples in order to increase the number of alternative materials and processes that is considered. Product examples can c...... a search engine, and through hyperlinks can relevant materials and processes be explored. Realising that designers are very sensitive to user interfaces do all descriptions of materials, processes and products include graphical descriptions, i.e. pictures or computer graphics....

75 FR 57830 - Office of Hazardous Materials Safety; Notice of Applications for Modification of Special Permit

Science.gov (United States)

2010-09-22

... permits (e.g. to provide for additional hazardous materials, packaging design changes, additional mode of... special permit Application No. Docket No. Applicant affected thereof 7951-M ConAgra Foods, 49 CFR To... outer packaging when no other means of transportation exist. 14953-M Applied 49 CFR To modify the...

Assessment of natural radioactivity and the associated radiation hazards in some Cameroonian building materials

International Nuclear Information System (INIS)

Ngachin, M.; Garavaglia, M.; Giovani, C.; Kwato Njock, M.G.

2005-09-01

The concentration of 238 U, 232 Th, 40 K in natural and fabricated building materials used in Cameroon was investigated by a high-resolution γ-ray spectrometry system with a co-axial HPGe detector. Fourteen kinds of building materials were collected from factories and in the field. Each sample was therefore kept in a 500 ml plastic Marinelli beakers and measured in a very low-background laboratory. The measured activity concentrations range from 1.76 to 49.84 Bq kg -1 , from 0.32 to 147.2 Bq kg -1 and from 18.16 to 1226.29 Bq kg -1 for 238 U, 232 Th and 40 K respectively. The highest mean value of 238 U concentration was found in red compressed soil-brick type I (49.57±0.33 Bq kg -1 ) produced by MIPROMALO whereas the highest average concentration of 232 Th (138.89±12.51 Bq kg -1 ) and 40 K (1161.46±107.57 Bq kg -1 ) was found in gravel collected from an exploitation site in LOGBADJECK. The activity concentrations obtained were compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra eq , the external hazard index H ex as well as the indoor absorbed dose rate D radical in air and the annual effective dose equivalent H radical E were evaluated to assess the radiation hazards for people living in dwellings made of studied materials. All building materials have shown Ra eq activity (range from 10.15 to 312.57 Bq kg -1 ) lower than the limit of 370 Bq kg -1 set in the Organization for Economic Cooperation and Development (OECD, 1979) report, and which is equivalent to a γ-dose of 1.5 mSv yr -1 All the examined materials are acceptable for use as building materials in accord with the OECD criterion. (author)

Materials selection for a transport packaging of Mo-99

International Nuclear Information System (INIS)

Hara, Debora H.S.; Lucchesi, Raquel F.; Mancini, Victor A.; Rossi, Jesualdo L.; Fiore, Marina

2015-01-01

The radiopharmaceuticals are radioactive isotopes used in nuclear medicine for more accurate diagnosis and treatment of diseases or dysfunctions. Currently, the most important radionuclide for the preparation of radiopharmaceuticals for diagnostic purposes is technetium-99m ( 99m Tc), a product of the radioactive decay of molybdenum-99 (Mo-99). The aim of this work was the materials selection that can enable the manufacture of a package for Mo-99 transport with the aid of CES EduPack program and the methodology developed by Ashby. The ESTAR program was used to check the occurrence of Bremsstrahlung and the XCOM program was used to calculate the attenuation coefficient of gamma radiation from some of the selected materials for the shield; after, the thickness required for radiation shielding was calculated. From the results, the materials selected as potential candidates for the manufacture of the shielding were the tungsten alloys. Related to the thermal insulation and the impact protection, woods, plywoods and particle boards stand out. With regard to internal and external coatings, the selected materials focus on groups of steels and nickel alloys. (author)

Functional design criteria for the Hazardous Materials Management and Emergency Response (HAMMER) Training Center. Revision 1

International Nuclear Information System (INIS)

Sato, P.K.

1995-01-01

Within the United States, there are few hands-on training centers capable of providing integrated technical training within a practical application environment. Currently, there are no training facilities that offer both radioactive and chemical hazardous response training. There are no hands-on training centers that provide training for both hazardous material operations and emergency response that also operate as a partnership between organized labor, state agencies, tribes, and local emergency responders within the US Department of Energy (DOE) complex. Available facilities appear grossly inadequate for training the thousands of people at Hanford, and throughout the Pacific Northwest, who are required to qualify under nationally-mandated requirements. It is estimated that 4,000 workers at the Hanford Site alone need hands-on training. Throughout the Pacific Northwest, the potential target audience would be over 30,000 public sector emergency response personnel, as well as another 10,000 clean-up workers represented by organized labor. The HAMMER Training Center will be an interagency-sponsored training center. It will be designed, built, and operated to ensure that clean-up workers, fire fighters, and public sector management and emergency response personnel are trained to handle accidental spills of hazardous materials. Training will cover wastes at clean-up sites, and in jurisdictions along the transportation corridors, to effectively protect human life, property, and the environment

Conference: ActiWiz – Optimizing material selection at CERN's accelerators from the radiological point of view

CERN Multimedia

2012-01-01

by Dr. Helmut Vincke (CERN), Chris Theis (CERN). Tuesday, October 30, 2012 from 15:00 to 16:30 at CERN ( 864-1-D02 - BE Auditorium Prévessin ) Description: The operation of a high-energy accelerator inevitably triggers the activation of equipment, which poses a safety hazard. Consequently access and handling constraints have to be imposed to ensure optimized working conditions. One of the key parameters determining the level of radioactivity is the material composition. Considering the radiological impact in addition to the engineering requirements during the selection of material clearly results in a safety benefit as well as a more efficient accelerator operation due to less stringent access and handling constraints. Another aspect is the minimization of future radioactive waste, which constitutes an important part of CERN’s commitment to limit its environmental impact by applying best practices. The ActiWiz software developed at CERN provides an easy to use method to optimize the m...

Transport of hazardous goods

International Nuclear Information System (INIS)

1989-01-01

The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH) [de

Environmental Assessment For the Proposed Construction of A Hazardous Materials Issue Facility and a Hazardous Wastes Storage Facility at Buckley Air Force Base, Colorado

Science.gov (United States)

2005-04-01

hazardous materials in accordance with the Occupational Health and Safety Administration ( OSHA ) storage standards. This facility would make the...subcontinent including, for example, Cambodia, China, India, Japan, Korea, Malaysia , Pakistan, or the Philippine Islands; and • Native Hawaiian and Other...regulated by the USEPA and the OSHA . The state of Colorado also has regulations pertaining to ACM abatement. Emissions of asbestos fibers into the

The National Shipbuilding Research Program, 1990 Ship Production Symposium, Paper No. 4B-1: Solving SARA Compliance with Computerized Hazardous Materials Tracking

National Research Council Canada - National Science Library

Johnston, Don; Schoenleber, Dave

1990-01-01

...) has forced facilities to keep track of hazardous materials as never before. EPCRA contains five major reporting requirements including planning notification, emergency release notification, Material Safety Data Sheet (MSDS...

Hazardous materials in aquatic environments of the Mississippi River Basin

International Nuclear Information System (INIS)

1993-01-01

Tulane and Xavier Universities have singled out the environment as a major strategic focus for research and training for now and by the year 2000. In December, 1992, the Tulane/Xavier CBR was awarded a five year grant to study pollution in the Mississippi River system. The ''Hazardous Materials in Aquatic Environments of the Mississippi River Basin'' project is a broad research and education program aimed at elucidating the nature and magnitude of toxic materials that contaminate aquatic environments of the Mississippi River Basin. Studies include defining the complex interactions that occur during the transport of contaminants, the actual and potential impact on ecological systems and health, and the mechanisms through which these impacts might be remediated. The Mississippi River Basin represents a model system for analyzing and solving contamination problems that are found in aquatic systems world-wide. These research and education projects are particularly relevant to the US Department of Energy's programs aimed at addressing aquatic pollution problems associated with DOE National Laboratories. First year funding supported seven collaborative cluster projects and twelve initiation projects. This report summarizes research results for period December 1992--December 1993

Waste package materials selection process

International Nuclear Information System (INIS)

Roy, A.K.; Fish, R.L.; McCright, R.D.

1994-01-01

The office of Civilian Radioactive Waste Management (OCRWM) of the United States Department of Energy (USDOE) is evaluating a site at Yucca Mountain in Southern Nevada to determine its suitability as a mined geologic disposal system (MGDS) for the disposal of high-level nuclear waste (HLW). The B ampersand W Fuel Company (BWFC), as a part of the Management and Operating (M ampersand O) team in support of the Yucca Mountain Site Characterization Project (YMP), is responsible for designing and developing the waste package for this potential repository. As part of this effort, Lawrence Livermore National Laboratory (LLNL) is responsible for testing materials and developing models for the materials to be used in the waste package. This paper is aimed at presenting the selection process for materials needed in fabricating the different components of the waste package

Selecting materialized views in a data warehouse

Science.gov (United States)

Zhou, Lijuan; Liu, Chi; Liu, Daxin

2003-01-01

A Data Warehouse contains lots of materialized views over the data provided by the distributed heterogeneous databases for the purpose of efficiently implementing decision-support or OLAP queries. It is important to select the right view to materialize that answer a given set of queries. In this paper, we have addressed and designed algorithm to select a set of views to materialize in order to answer the most queries under the constraint of a given space. The algorithm presented in this paper aim at making out a minimum set of views, by which we can directly respond to as many as possible user"s query requests. We use experiments to demonstrate our approach. The results show that our algorithm works better. We implemented our algorithms and a performance study of the algorithm shows that the proposed algorithm gives a less complexity and higher speeds and feasible expandability.

Europa Lander Material Selection Considerations

Energy Technology Data Exchange (ETDEWEB)

Tappan, Alexander S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Heller, Mellisa [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-01-10

Energetic materials (EMs, explosives, pyrotechnics, propellants) provide high-power output of high temperature reaction products. These products can be solid, liquid, or gaseous during reaction or after the products have equilibrated with the surroundings. For example, high explosives typically consist of carbon, hydrogen, nitrogen, and oxygen bonded within a single molecule, and produce almost exclusively gaseous products. Conversely, intermetallics consist of physical mixtures of metals and metalloids, and produce almost exclusively condensed products. Other materials such as pyrotechnics and propellants have intermediate behavior. All energetic materials react in a self-propagating manner that after ignition, does not necessarily require energy input from the surroundings. The range of reaction velocities can range from mm/s for intermetallics, to km/s for high explosives. Energetic material selection depends on numerous requirements specific to the needs of a system. High explosives are used for applications where high pressure gases are necessary for pushing or fracturing materials (e.g., rock, metal) or creating shock waves or air blast. Propellants are used to produce moderate-pressure, high-temperature products without a shock wave. Pyrotechnics are used to produce numerous effects including: high-temperature products, gases, light, smoke, sound, and others. Thermites are used to produce heat, high-temperature products, materials, and other effects that require condensed products. Intermetallics are used to produce high-temperature condensed products and materials, with very little gas production. Numerous categories of energetic materials exist with overlapping definitions, effects, and properties.

Technologies to remediate hazardous waste sites

International Nuclear Information System (INIS)

Falco, J.W.

1990-03-01

Technologies to remediate hazardous wastes must be matched with the properties of the hazardous materials to be treated, the environment in which the wastes are imbedded, and the desired extent of remediation. Many promising technologies are being developed, including biological treatment, immobilization techniques, and in situ methods. Many of these new technologies are being applied to remediate sites. The management and disposal of hazardous wastes is changing because of federal and state legislation as well as public concern. Future waste management systems will emphasize the substitution of alternatives for the use of hazardous materials and process waste recycling. Onsite treatment will also become more frequently adopted. 5 refs., 7 figs

Study on hazardous substances contained in radioactive waste

International Nuclear Information System (INIS)

Kuroki, Ryoichiro; Takahashi, Kuniaki

2008-01-01

It is necessary that the technical criteria is established concerning waste package for disposal of the TRU waste generated in Japan Atomic Energy Agency. And it is important to consider the criteria not only in terms of radioactivity but also in terms of chemical hazard and criticality. Therefore the environmental impact of hazardous materials and possibility of criticality were investigated to decide on technical specification of radioactive waste packages. The contents and results are as following. (1) Concerning hazardous materials included in TRU waste, regulations on disposal of industrial wastes and on environmental preservation were investigated. (2) The assessment methods for environmental impact of hazardous materials included in radioactive waste in U.K, U.S.A. and France were investigated. (3) The parameters for mass transport assessment about migration of hazardous materials in waste packages around disposal facilities were compiled. And the upper limits of amounts of hazardous materials in waste packages to satisfy the environmental standard were calculated with mass transport assessment for some disposal concepts. (4) It was suggested from criticality analysis for waste packages in disposal facility that the occurrence of criticality was almost impossible under the realistic conditions. (author)

Properties of selected superconductive materials, 1978 supplement. Technical note

International Nuclear Information System (INIS)

Roberts, B.W.

1978-10-01

This report includes data on additional superconductive materials extracted from the world literature up to fall 1977 and is an addendum to the data set published in J. Phys. Chem. Ref. Data 5, no. 3, 581-821 (1976) (Reprint no. 84). The data presented are new values and have not been selected or compared to values (except for selected values of the elements) previously assembled by the Superconductive Materials Data Center. The properties included are composition, critical temperature, critical magnetic field, crystal structure and the results of negative experiments. Special tabulations of high magnetic field materials with Type II behavior and materials with organic components are included. All entries are keyed to the literature. A list of recent reviews centered on superconductive materials is included

Transportation of radioactive, hazardous, and mixed wastes: Material identification is the key

International Nuclear Information System (INIS)

Stancell, D.F.; Willaford, D.M.

1992-01-01

This paper will discuss how material identification and classification will result in an accurate determination of regulatory requirements, and will assure safe and compliant shipment of radioactive, hazardous, and mixed wastes. The primary focus of the paper is a discussion of lessons learned by the Department of Energy in making waste shipments, and how this can be applied to future mixed waste shipments. There will be a brief discussion of the Department's regulatory compliance program, including a presentation of compliance audit results, and how regulatory issues are addressed through effective information exchange, technical assistance, and compliance training. A detailed discussion will follow, which describes cases involving material identification and classification problems. Examples will include both RCRA waste and uranium mill tailings shipments. The paper will conclude with a discussion concerning the application of these lessons to future mixed waste shipments proposed by the Department. (author)

''Hazardous'' terminology

International Nuclear Information System (INIS)

Powers, J.

1991-01-01

A number of terms (e.g., ''hazardous chemicals,'' ''hazardous materials,'' ''hazardous waste,'' and similar nomenclature) refer to substances that are subject to regulation under one or more federal environmental laws. State laws and regulations also provide additional, similar, or identical terminology that may be confused with the federally defined terms. Many of these terms appear synonymous, and it easy to use them interchangeably. However, in a regulatory context, inappropriate use of narrowly defined terms can lead to confusion about the substances referred to, the statutory provisions that apply, and the regulatory requirements for compliance under the applicable federal statutes. This information Brief provides regulatory definitions, a brief discussion of compliance requirements, and references for the precise terminology that should be used when referring to ''hazardous'' substances regulated under federal environmental laws. A companion CERCLA Information Brief (EH-231-004/0191) addresses ''toxic'' nomenclature

Implications of material selection on the design of packaging machinery.

Science.gov (United States)

Merritt, J P

2009-01-01

Material selection has significant implications on the design and cost of horizontal-form-fill-seal packaging machinery. To avoid excessive costs, machine redesigns and project delays, material selection must be reconciled early in the project and revisited throughout the construction of the machine.

Effectiveness of Awareness Package on Occupational Health Hazards among Ragpickers of New Delhi, India.

Science.gov (United States)

Agarwalla, Rashmi; Pathak, Rambha; Singh, Mitasha; Islam, Farzana; Parashar, Mamta

2017-01-01

Ragpickers are informal workers who collect recyclable materials to earn a small wage on daily basis. They work in vulnerable conditions and awareness regarding occupational and environmental hazard is essential for them. To study the effectiveness of awareness program on various occupational health hazards among the ragpickers. This interventional study was conducted from May through October 2016 among the ragpickers living near field practice area of Department of Community Medicine and those living in slum areas around HAHC Hospital, New Delhi, India. The awareness regarding occupational and environmental health hazards was assessed using a pretested and predesigned pro forma. Snowball sampling technique was used to select the ragpickers from the various areas. Health awareness and education package was designed for the ragpickers. The package was delivered by medical officers and health workers. A posttest assessment was done 2 weeks after the awareness activity. Among 150 ragpickers, there was significant improvement in knowledge immediate post training on knowledge of occupational hazard and hygiene. Efforts should be put to develop training materials on occupation and environmental health and injury issue relating to waste management.

Preliminary hazards analysis -- vitrification process

International Nuclear Information System (INIS)

Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P.

1994-06-01

This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility's construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment

Preliminary hazards analysis -- vitrification process

Energy Technology Data Exchange (ETDEWEB)

Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P. [Science Applications International Corp., Pleasanton, CA (United States)

1994-06-01

This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility`s construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment.

Sustainable System for Residual Hazards Management

International Nuclear Information System (INIS)

Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

2004-01-01

Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today's waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous long-term management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by external intrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the long-term success of the prescribed system. In fact

A fuzzy logic based PROMETHEE method for material selection problems

Directory of Open Access Journals (Sweden)

Muhammet Gul

2018-03-01

Full Text Available Material selection is a complex problem in the design and development of products for diverse engineering applications. This paper presents a fuzzy PROMETHEE (Preference Ranking Organization Method for Enrichment Evaluation method based on trapezoidal fuzzy interval numbers that can be applied to the selection of materials for an automotive instrument panel. Also, it presents uniqueness in making a significant contribution to the literature in terms of the application of fuzzy decision-making approach to material selection problems. The method is illustrated, validated, and compared against three different fuzzy MCDM methods (fuzzy VIKOR, fuzzy TOPSIS, and fuzzy ELECTRE in terms of its ranking performance. Also, the relationships between the compared methods and the proposed scenarios for fuzzy PROMETHEE are evaluated via the Spearman’s correlation coefficient. Styrene Maleic Anhydride and Polypropylene are determined optionally as suitable materials for the automotive instrument panel case. We propose a generic fuzzy MCDM methodology that can be practically implemented to material selection problem. The main advantages of the methodology are consideration of the vagueness, uncertainty, and fuzziness to decision making environment.

Radiological hazards due to naturally occurring radionuclides in the selected building materials used for the construction of dwellings in four districts of the Punjab Province, Pakistan.

Science.gov (United States)

Rahman, S U; Rafique, M; Jabbar, A; Matiullah

2013-03-01

This paper presents the finding of a study undertaken to determine the naturally occurring radionuclides present in commonly used building materials for dwellings and workplaces in four districts of the Punjab Province, Pakistan. The concentrations of (226)Ra, (232)Th and (40)K were measured by using gamma-ray spectroscopy. A total of 80 samples of building materials were collected from various manufacturers and suppliers of the studied area. The specific activities of (226)Ra, (232)Th and (40)K were measured in building samples, and results ranged from minimum values of 9 ± 1, 9 ± 2 and 27 ± 8 Bq kg(-1) to maximum values of 106 ± 5, 133 ± 5 and 914 ± 21 Bq kg(-1) with mean values of 42 ± 3, 48 ± 3 and 376 ± 16 Bq kg(-1), respectively. From the measured activity concentrations, equivalent radium (Ra(eq)), terrestrial absorbed dose rate, annual effective dose as well as external and internal hazard indices were calculated and found to range from 52 ± 7 to 274 ± 15 Bq kg(-1), 23 ± 3 to 130 6 nGy h(-1), 0.15 ± 0.02 to 0.80 ± 0.03 mSv, 0.14 ± 0.02 to 0.75 ± 0.04 and 0.2 ± 0.02 to 0.98 ± 0.05, respectively. These results were comparable to the results of similar studies undertaken locally and in other countries. The samples considered were safe for use in construction of dwellings in the study area and do not pose any significant source of radiation hazard.

Assessment and selection of materials for ITER in-vessel components

Science.gov (United States)

Kalinin, G.; Barabash, V.; Cardella, A.; Dietz, J.; Ioki, K.; Matera, R.; Santoro, R. T.; Tivey, R.; ITER Home Teams

2000-12-01

During the international thermonuclear experimental reactor (ITER) engineering design activities (EDA) significant progress has been made in the selection of materials for the in-vessel components of the reactor. This progress is a result of the worldwide collaboration of material scientists and industries which focused their effort on the optimisation of material and component manufacturing and on the investigation of the most critical material properties. Austenitic stainless steels 316L(N)-IG and 316L, nickel-based alloys Inconel 718 and Inconel 625, Ti-6Al-4V alloy and two copper alloys, CuCrZr-IG and CuAl25-IG, have been proposed as reference structural materials, and ferritic steel 430, and austenitic steel 304B7 with the addition of boron have been selected for some specific parts of the ITER in-vessel components. Beryllium, tungsten and carbon fibre composites are considered as plasma facing armour materials. The data base on the properties of all these materials is critically assessed and briefly reviewed in this paper together with the justification of the material selection (e.g., effect of neutron irradiation on the mechanical properties of materials, effect of manufacturing cycle, etc.).

Green offal inspection of cattle, small ruminants and pigs in the United Kingdom: Impact assessment of changes in the inspection protocol on likelihood of detection of selected hazards.

Science.gov (United States)

Blagojevic, Bojan; Dadios, Nikolaos; Reinmann, Karin; Guitian, Javier; Stärk, Katharina D C

2015-06-01

The changes in detection of selected public and animal health as well as welfare hazards due to the change in current inspection of green offal in cattle, small ruminants and pigs were assessed. With respect to public health and animal health, the conditional likelihood of detection with the current green offal inspection was found to be low for eleven out of the twenty-four selected hazard-species pairings and very low for the remaining thirteen pairings. This strongly suggests that the contribution of current green offal inspection to risk mitigation is very limited for public and animal health hazards. The removal of green offal inspection would reduce the detection of some selected animal welfare conditions. For all selected public and animal health as well as welfare hazards, the reduced detection could be compensated with other pre-harvest, harvest and/or post-harvest control measures including existing meat inspection tasks. Copyright © 2015 Elsevier Ltd. All rights reserved.

75 FR 34573 - Bulk Solid Hazardous Materials: Harmonization With the International Maritime Solid Bulk Cargoes...

Science.gov (United States)

2010-06-17

... reduced iron (DRI) as briquettes molded at a temperature of 650 [deg]C or higher that have a density of 5... temperature of 650 [deg]C or higher or had a density of 5.0 g/cm[sup3] or greater. In this proposed rule, we... bulk materials of Hazard Classes 4 through 9. c. One comment recommended that a DCM be required for...

78 FR 41853 - Safety Advisory Guidance: Heating Rail Tank Cars To Prepare Hazardous Material for Unloading or...

Science.gov (United States)

2013-07-12

... rail tank car due to chemical self-reaction and expansion of the toluene diisocyanate matter wastes. On...: Cheryl West Freeman, Division of Engineering and Research, Pipeline and Hazardous Materials Safety... catastrophically ruptured at a transfer station at the BASF Corporation chemical facility in Freeport, Texas. The...

Proposal of risk evaluation methodology for hazardous materials transportation

International Nuclear Information System (INIS)

Hartman, Luiz Carlos

2009-01-01

The increasing concern with the level of risk associated with the transportation of hazardous materials took some international institutions to pledge efforts in the evaluation of risk in regional level. Following this trend, the objective of this work was to analyze the most recent processes of analysis of risks from road transportation of hazardous materials. In the present work 21 methodologies of analysis of risks, developed by some authors and for diverse localities have been evaluated. Two of them, in special, have been reviewed and discussed: a method recently developed by the Swiss Federal Institute of Technology (Nicolet-Monnier and Gheorghe, 1996) and the strategy delineated by the Center for Chemical Process Safety CCPS (1995), taking into consideration the estimate of the individual and social risk. Also, the models of Harwood et al. (1990) and of Ramos (1997), adapted by Hartman (2003) have been applied to the reality of the roads of the state of Sao Paulo. The extension of these methodologies was explored, in order to find its advantages and disadvantages. As a study case the present work considered the ammonia transportation throughout two routes evaluating the reality of the roads of the state of Sao Paulo, including a significant parcel of evaluation in a densely populated area, getting the results using risk, at least, one of the methodologies mentioned above. The innovation proposed by this work was the research, the development and the introduction of two variables to the model considered by Harwood et al. (1990). These variables that influence in the value of the risk are: the age of the driver of truck and the zone of impact that is function type of product, period of the day where the transport was carried and the volume that has been transported. The aim of the proposed modifications is to let the value of the risk more sensible in relation to the type of the product carried and the age of the truck driver. The main related procedural stages

Graphic products used in the evaluation of traditional and emerging remote sensing technologies for the detection of fugitive contamination at selected superfund hazardous waste sites

Science.gov (United States)

Slonecker, E. Terrence; Fisher, Gary B.

2011-01-01

This report presents the overhead imagery and field sampling results used to prepare U.S. Geological Survey Open-File Report 2011-1050, 'Evaluation of Traditional and Emerging Remote Sensing Technologies for the Detection of Fugitive Contamination at Selected Superfund Hazardous Waste Sites'. These graphic products were used in the evaluation of remote sensing technology in postclosure monitoring of hazardous waste sites and represent an ongoing research effort. Soil sampling results presented here were accomplished with field portable x-ray fluoresence (XRF) technology and are used as screening tools only representing the current conditions of metals and other contaminants at selected Superfund hazardous waste sites.

Basic Thermal Parameters of Selected Foods and Food Raw Materials

OpenAIRE

Monika Božiková; Ľubomír Híreš; Michal Valach; Martin Malínek; Jan Mareček

2017-01-01

In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of ...

Protective Behaviour of Citizens to Transport Accidents Involving Hazardous Materials: A Discrete Choice Experiment Applied to Populated Areas nearby Waterways.

Directory of Open Access Journals (Sweden)

Esther W de Bekker-Grob

Full Text Available To improve the information for and preparation of citizens at risk to hazardous material transport accidents, a first important step is to determine how different characteristics of hazardous material transport accidents will influence citizens' protective behaviour. However, quantitative studies investigating citizens' protective behaviour in case of hazardous material transport accidents are scarce.A discrete choice experiment was conducted among subjects (19-64 years living in the direct vicinity of a large waterway. Scenarios were described by three transport accident characteristics: odour perception, smoke/vapour perception, and the proportion of people in the environment that were leaving at their own discretion. Subjects were asked to consider each scenario as realistic and to choose the alternative that was most appealing to them: staying, seeking shelter, or escaping. A panel error component model was used to quantify how different transport accident characteristics influenced subjects' protective behaviour.The response was 44% (881/1,994. The predicted probability that a subject would stay ranged from 1% in case of a severe looking accident till 62% in case of a mild looking accident. All three transport accident characteristics proved to influence protective behaviour. Particularly a perception of strong ammonia or mercaptan odours and visible smoke/vapour close to citizens had the strongest positive influence on escaping. In general, 'escaping' was more preferred than 'seeking shelter', although stated preference heterogeneity among subjects for these protective behaviour options was substantial. Males were less willing to seek shelter than females, whereas elderly people were more willing to escape than younger people.Various characteristics of transport accident involving hazardous materials influence subjects' protective behaviour. The preference heterogeneity shows that information needs to be targeted differently depending on

Hazards assessment for the INEL Landfill Complex

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment

Hazards assessment for the INEL Landfill Complex

Energy Technology Data Exchange (ETDEWEB)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment.

The Protection of Cultural Heritage Sites from Geo-Hazards

Science.gov (United States)

Themistocleous, Kyriacos; Agapiou, Athos; Cuca, Branka; Lysandrou, Vasiliki; Tzouvaras, Marios; Michaelides, Silas; Hadjimitsis, Diofantos; Margottini, Claudio; Cigna, Francesca; Crosta, Giovanni; Fernandez, Jose

2016-04-01

Cultural heritage sites are continuously impacted by several environmental and anthropogenic factors, including climate change, precipitation, natural hazards, wars, etc. However, there is limited data available regarding the effects of geo-hazards on cultural heritage sites. This paper presents the methodology of the PROTHEGO project, which uses radar interferometry to monitor surface deformation with mm precision to analyze the impact of geo-hazards in cultural heritage sites in Europe. PROTHEGO will provide a new, low-cost methodological approach for the safe management of cultural heritage monuments and sites located in Europe. The project will apply InSAR techniques to monitor monuments and sites that are potentially unstable due to landslides, sinkholes, settlement, subsidence, active tectonics as well as structural deformation, all of which can be effected of climate change and human interaction. The research methodology will be focused on long-term low-impact monitoring systems as well as indirect analysis of environmental contexts to investigate changes and decay of structure, material and landscape. The methodology will be applied to more than 450 sites on the UNESCO World Heritage List in geographical Europe. One of the case study selected is located in Cyprus at Choirokoitia, which is a UNESCO World Heritage site. The outcomes of PROTHEGO will support correct planning and rebalancing the contrast between endogenous (structural and materials decay, the societal development, the anthropogenic pressure) and surrounding exogenous forces (natural hazards acting on the heritage) which affecting the European cultural heritage.

Optimal materials selection for bimaterial piezoelectric microactuators

OpenAIRE

Srinivasan, P.; Spearing, S.M.

2008-01-01

Piezoelectric actuation is one of the commonly employed actuation schemes in microsystems. This paper focuses on identifying and ranking promising active material/substrate combinations for bimaterial piezoelectric (BPE) microactuators based on their performance. The mechanics of BPE structures following simple beam theory assumptions available in the literature are applied to evolve critical performance metrics which govern the materials selection process. Contours of equal performance are p...

Disposal of hazardous wastes

International Nuclear Information System (INIS)

Barnhart, B.J.

1978-01-01

The Fifth Life Sciences Symposium entitled Hazardous Solid Wastes and Their Disposal on October 12 through 14, 1977 was summarized. The topic was the passage of the National Resources Conservation and Recovery Act of 1976 will force some type of action on all hazardous solid wastes. Some major points covered were: the formulation of a definition of a hazardous solid waste, assessment of long-term risk, list of specific materials or general criteria to specify the wastes of concern, Bioethics, sources of hazardous waste, industrial and agricultural wastes, coal wastes, radioactive wastes, and disposal of wastes

Project T100 -- Hazardous Materials Management and Emergency Response Training Center (HAMMER)

International Nuclear Information System (INIS)

Norton, C.E.

1994-01-01

The scope of this Quality Assurance Program Plan (QAPP) is to provide a system of Quality Assurance reviews and verifications on the design and construction of the Hazardous Materials Management and Emergency Response (HAMMER) Training Center, project 95L-EWT-100 at Hanford. The reviews and verifications will be on activities associated with design, procurement, and construction of the HAMMER project which includes, but is not limited to earthwork, placement of concrete, laying of rail, drilling of wells, water and sewer line fabrication and installation, communications systems, fire protection/detection systems, line tie-ins, building and mock-up (prop) construction, electrical, instrumentation, pump and valves and special coatings

User's guide for the KBERT 1.0 code: For the knowledge-based estimation of hazards of radioactive material releases from DOE nuclear facilities

International Nuclear Information System (INIS)

Browitt, D.S.; Washington, K.E.; Powers, D.A.

1995-07-01

The possibility of worker exposure to radioactive materials during accidents at nuclear facilities is a principal concern of the DOE. The KBERT software has been developed at Sandia National Laboratories under DOE support to address this issue by assisting in the estimation of risks posed by accidents at chemical and nuclear facilities. KBERT is an acronym for Knowledge-Based system for Estimating hazards of Radioactive material release Transients. The current prototype version of KBERT focuses on calculation of doses and consequences to in-facility workers due to accidental releases of radioactivity. This report gives detailed instructions on how a user who is familiar with the design, layout and potential hazards of a facility can use KBERT to assess the risks to workers in that facility. KBERT is a tool that allows a user to simulate possible accidents and observe the predicted consequences. Potential applications of KBERT include the evaluation of the efficacy of evacuation practices, worker shielding, personal protection equipment and the containment of hazardous materials

Analysis of hazardous biological material by MALDI mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

KL Wahl; KH Jarman; NB Valentine; MT Kingsley; CE Petersen; ST Cebula; AJ Saenz

2000-03-21

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-MS) has become a valuable tool for analyzing microorganisms. The speed with which data can be obtained from MALDI-MS makes this a potentially important tool for biological health hazard monitoring and forensic applications. The excitement in the mass spectrometry community in this potential field of application is evident by the expanding list of research laboratories pursuing development of MALDI-MS for bacterial identification. Numerous research groups have demonstrated the ability to obtain unique MALDI-MS spectra from intact bacterial cells and bacterial cell extracts. The ability to differentiate strains of the same species has been investigated. Reproducibility of MALDI-MS spectra from bacterial species under carefully controlled experimental conditions has also been demonstrated. Wang et al. have reported on interlaboratory reproducibility of the MALDI-MS analysis of several bacterial species. However, there are still issues that need to be addressed, including the careful control of experimental parameters for reproducible spectra and selection of optimal experimental parameters such as solvent and matrix.

Radionuclide content and associated radiation hazards of building materials and by-products in Baoji, West China

International Nuclear Information System (INIS)

Lu, X.; Zhang, X.

2008-01-01

Seven types of common building materials and by-products of coal-fired power plants collected from Baoji, West China, were analysed for the natural radioactivity of 226 Ra, 232 Th and 40 K using gamma ray spectrometry with an NaI(Tl) detector. The average activity concentrations vary from 23.0 to 112.2, 20.2 to 147.5 and 113.2 to 890.8 Bq kg -1 for 226 Ra, 232 Th and 40 K, respectively. The measured activity concentrations for these radionuclides were compared with the data reported from other countries and with the worldwide average activity of soil. As a measure of radiation hazard to the people, the radium equivalent activities, total annual effective dose and activity concentration index were estimated. The radium equivalent activities of the studied samples are below the internationally accepted values. The calculated total annual effective dose and the activity concentration index of seven types of common building materials are -1 and 1, respectively. But fly ash and bottom ash exhibit the higher values that exceed and be close to the acceptable values, respectively. This study shows that the measured building materials do not pose any significant source of radiation hazard and are safe for use in the construction of dwellings. Nevertheless, when fly ash and bottom ash are used in dwelling construction, it is important to assess their radiation potential. (authors)

Chemical studies on the synthesis and characterization of some ion- exchange materials and its use in the treatment of hazardous wastes

International Nuclear Information System (INIS)

El-Deeb, A.B.I.

2013-01-01

Now inorganic ion exchange materials play an important role in analytical chemistry, based originally on their thermal and radiation resistance as well as their stability to chemical attack.Vanadate salts are one of the main categories of inorganic ion exchange materials widely used in separation and preconcentration of some toxic and hazardous elements from different waste media. Attempts in this study are focused on the preparation of two inorganic ion exchange materials ,Tin Vanadate (SnV) and Titanium Potassium Vanadate(TiKV) for treatment of hazardous waste.These material were characterized using X-ray spectra (XRD and XRF), IR, TGA-DTA and total elemental analysis studies. On the basis of distribution studies, the materials have been found that they are highly selective for Pb(II) and Cs(I)ions. Thermodynamic parameters (i.e. ΔG, ΔS and ΔH) have also been calculated for the adsorption of Pb 2+ , Cs + , Fe 3+ , Cd 2+ , Cu +2 , Zn 2+ and Co 2+ ions on Tin Vanadate (SnV) and Titanium Potassium Vanadate(TiKV) showing that the overall adsorption process is spontaneous and endothermic. The mechanism of diffusion of Fe 3+ , Co 2+ , Cu 2+ , Zn 2+ , Cd 2+ , Cs + and Pb 2+ ions for Tin Vanadate (SnV) and Titanium Potassium Vanadate(TiKV) as cation exchangers were studied as a function of particle size, concentration of the exchanging ions, reaction temperatures and drying temperatures. The exchange rate was controlled by a particle diffusion mechanism as a limited batch technique and is confirmed from straight lines of B versus 1/r 2 plots. The values of diffusion coefficients, activation energies and entropies of activation were calculated and their significance was discussed. The data obtained have been compared with that reported for other inorganic exchangers. Exchange isotherms for Cs + ,Co 2+ and Cd 2+ ions were determined at 25, 45 and 65±1 degree C. These isotherms showed that Cs + ,Co 2+ and Cd 2+ are physically adsorbed. Finally, separations of the above

International conference and workshop on modeling and mitigating the consequences of accidental releases of hazardous materials

International Nuclear Information System (INIS)

Anon.

1995-01-01

This conference was held September 26--29, 1995 in New Orleans, Louisiana. The purpose of this conference was to provide a multidisciplinary forum for exchange of state-of-the-art information on the consequences of accidental releases of hazardous materials. Attention is focused on air dispersion of vapors. Individual papers have been processed separately for inclusion in the appropriate data bases

Material selection for design, manufacturing and application

International Nuclear Information System (INIS)

Zaid, A.I.O.

2011-01-01

Developing a new engineering material product or changing an existing one requires new design selecting material and choosing appropriate and economical manufacturing processes. These three main factors play a great role on the performance of the product in service. These items are independent and should not be performed in isolation from each other. With the great advancement of technology in the last decade and with the greater number of engineering materials which are now available, together with the increasing pressure to produce more economic and get reliable products an integrated approach which considers design, material selection and the appropriate manufacturing process makes it easier to achieve the optimum product that combines the functional requirements with the reliability at competitive cost. These diverse activities or items are interdependent; therefore should not be considered in isolation from each other, for example, it is not sufficient that design of the product should satisfy the technical, safety and legal requirements, it must also be possible to be manufactured economically and to be sold at a competitive price and easily disposed at the end of its working life cycle. In this paper, the interaction of these items together in order to arrive to the optimum solution for a particular application are given and discussed. (author)

Review of selective laser melting: Materials and applications

Energy Technology Data Exchange (ETDEWEB)

Yap, C. Y., E-mail: cyap001@e.ntu.edu.sg [Singapore Centre for 3D Printing, School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Block N3.1 - B2c - 01, Singapore 639798 (Singapore); Energy Research Institute @ NTU, Interdisciplinary Graduate School, Nanyang Technological University, 50 Nanyang Avenue, Block S2 - B3a - 01, Singapore 639798 (Singapore); Chua, C. K., E-mail: mckchua@ntu.edu.sg; Liu, Z. H., E-mail: azhliu@ntu.edu.sg; Zhang, D. Q., E-mail: zhangdq@ntu.edu.sg; Loh, L. E., E-mail: leloh1@e.ntu.edu.sg; Sing, S. L., E-mail: sing0011@e.ntu.edu.sg [Singapore Centre for 3D Printing, School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, Block N3.1 - B2c - 01, Singapore 639798 (Singapore); Dong, Z. L., E-mail: zldong@ntu.edu.sg [School of Materials Science & Engineering, Nanyang Technological University, 50 Nanyang Avenue, Block N4.1, Singapore 639798 (Singapore)

2015-12-15

Selective Laser Melting (SLM) is a particular rapid prototyping, 3D printing, or Additive Manufacturing (AM) technique designed to use high power-density laser to melt and fuse metallic powders. A component is built by selectively melting and fusing powders within and between layers. The SLM technique is also commonly known as direct selective laser sintering, LaserCusing, and direct metal laser sintering, and this technique has been proven to produce near net-shape parts up to 99.9% relative density. This enables the process to build near full density functional parts and has viable economic benefits. Recent developments of fibre optics and high-power laser have also enabled SLM to process different metallic materials, such as copper, aluminium, and tungsten. Similarly, this has also opened up research opportunities in SLM of ceramic and composite materials. The review presents the SLM process and some of the common physical phenomena associated with this AM technology. It then focuses on the following areas: (a) applications of SLM materials and (b) mechanical properties of SLM parts achieved in research publications. The review is not meant to put a ceiling on the capabilities of the SLM process but to enable readers to have an overview on the material properties achieved by the SLM process so far. Trends in research of SLM are also elaborated in the last section.

Review of selective laser melting: Materials and applications

Science.gov (United States)

Yap, C. Y.; Chua, C. K.; Dong, Z. L.; Liu, Z. H.; Zhang, D. Q.; Loh, L. E.; Sing, S. L.

2015-12-01

Selective Laser Melting (SLM) is a particular rapid prototyping, 3D printing, or Additive Manufacturing (AM) technique designed to use high power-density laser to melt and fuse metallic powders. A component is built by selectively melting and fusing powders within and between layers. The SLM technique is also commonly known as direct selective laser sintering, LaserCusing, and direct metal laser sintering, and this technique has been proven to produce near net-shape parts up to 99.9% relative density. This enables the process to build near full density functional parts and has viable economic benefits. Recent developments of fibre optics and high-power laser have also enabled SLM to process different metallic materials, such as copper, aluminium, and tungsten. Similarly, this has also opened up research opportunities in SLM of ceramic and composite materials. The review presents the SLM process and some of the common physical phenomena associated with this AM technology. It then focuses on the following areas: (a) applications of SLM materials and (b) mechanical properties of SLM parts achieved in research publications. The review is not meant to put a ceiling on the capabilities of the SLM process but to enable readers to have an overview on the material properties achieved by the SLM process so far. Trends in research of SLM are also elaborated in the last section.

Review of selective laser melting: Materials and applications

International Nuclear Information System (INIS)

Yap, C. Y.; Chua, C. K.; Liu, Z. H.; Zhang, D. Q.; Loh, L. E.; Sing, S. L.; Dong, Z. L.

2015-01-01

Selective Laser Melting (SLM) is a particular rapid prototyping, 3D printing, or Additive Manufacturing (AM) technique designed to use high power-density laser to melt and fuse metallic powders. A component is built by selectively melting and fusing powders within and between layers. The SLM technique is also commonly known as direct selective laser sintering, LaserCusing, and direct metal laser sintering, and this technique has been proven to produce near net-shape parts up to 99.9% relative density. This enables the process to build near full density functional parts and has viable economic benefits. Recent developments of fibre optics and high-power laser have also enabled SLM to process different metallic materials, such as copper, aluminium, and tungsten. Similarly, this has also opened up research opportunities in SLM of ceramic and composite materials. The review presents the SLM process and some of the common physical phenomena associated with this AM technology. It then focuses on the following areas: (a) applications of SLM materials and (b) mechanical properties of SLM parts achieved in research publications. The review is not meant to put a ceiling on the capabilities of the SLM process but to enable readers to have an overview on the material properties achieved by the SLM process so far. Trends in research of SLM are also elaborated in the last section

Phase Change Material Selection for Thermal Energy Storage at High Temperature Range between 210 °C and 270 °C

Directory of Open Access Journals (Sweden)

José Miguel Maldonado

2018-04-01

Full Text Available The improvement of thermal energy storage systems implemented in solar technologies increases not only their performance but also their dispatchability and competitiveness in the energy market. Latent heat thermal energy storage systems are one of those storing methods. Therefore, the need of finding the best materials for each application becomes an appealing research subject. The main goal of this paper is to find suitable and economically viable materials able to work as phase change material (PCM within the temperature range of 210–270 °C and endure daily loading and unloading processes in a system with Fresnel collector and an organic Rankine cycle (ORC. Twenty-six materials have been tested and characterized in terms of their thermophysical conditions, thermal and cycling stability, and health hazard. Two materials out of the 26 candidates achieved the last stage of the selection process. However, one of the two finalists would require an inert working atmosphere, which would highly increase the cost for the real scale application. This leads to a unique suitable material, solar salt (40 wt % KNO3/60 wt % NaNO3.

Materials, processes, and environmental engineering network

Science.gov (United States)

White, Margo M.

1993-01-01

The Materials, Processes, and Environmental Engineering Network (MPEEN) was developed as a central holding facility for materials testing information generated by the Materials and Processes Laboratory. It contains information from other NASA centers and outside agencies, and also includes the NASA Environmental Information System (NEIS) and Failure Analysis Information System (FAIS) data. Environmental replacement materials information is a newly developed focus of MPEEN. This database is the NASA Environmental Information System, NEIS, which is accessible through MPEEN. Environmental concerns are addressed regarding materials identified by the NASA Operational Environment Team, NOET, to be hazardous to the environment. An environmental replacement technology database is contained within NEIS. Environmental concerns about materials are identified by NOET, and control or replacement strategies are formed. This database also contains the usage and performance characteristics of these hazardous materials. In addition to addressing environmental concerns, MPEEN contains one of the largest materials databases in the world. Over 600 users access this network on a daily basis. There is information available on failure analysis, metals and nonmetals testing, materials properties, standard and commercial parts, foreign alloy cross-reference, Long Duration Exposure Facility (LDEF) data, and Materials and Processes Selection List data.

Integrated shape and material selection for single and multi-performance criteria

International Nuclear Information System (INIS)

Singh, Jasveer; Mirjalili, Vahid; Pasini, Damiano

2011-01-01

Research highlights: → The method of shape transformers is extended to torsional stiffness and combined load design. → The method is generalized for multi-criteria selection of shape and material. → Performance charts are presented for single and multi-objective selection of cross-section shape and material. → A four quadrant performance chart is presented to visualize the relation between objective function space and design variable space. -- Abstract: A shape and material selection method, based on the concept of shape transformers, has been recently introduced to characterize the mass efficiency of lightweight beams under bending and shear. This paper extends this method to deal with the case of torsional stiffness design, and generalize it to single and multi-crieria selection of lightweight shafts subjected to a combination of bending, shear, and torsional load. The novel feature of the paper is the useful integration of shape and material to model and visualize multi-objective selection problems. The scheme is centered on concept selection in structural design, and hinges on measures that govern the shape properties of a cross-section regardless of its size. These measures, referred as shape transformers, can classify shapes in a way similar to material classification. The procedure is exemplified by considering torsional stiffness as a constraint. The performance charts are developed for single and multi-criteria to visualize in a glance the whole range of cross-sectional shapes for each material. Each design chart is explained with a brief example.

Preliminary selection criteria for the Yucca Mountain Project waste package container material

International Nuclear Information System (INIS)

Halsey, W.G.

1991-01-01

The Department of Energy's Yucca Mountain Project (YMP) is evaluating a site at Yucca Mountain in Nevada for construction of a geologic repository for the storage of high-level nuclear waste. Lawrence Livermore National Laboratory's (LLNL) Nuclear Waste Management Project (NWMP) has the responsibility for design, testing, and performance analysis of the waste packages. The design is performed in an iterative manner in three sequential phases (conceptual design, advanced conceptual design, and license application design). An important input to the start of the advanced conceptual design is the selection of the material for the waste containers. The container material is referred to as the 'metal barrier' portion of the waste package, and is the responsibility of the Metal Barrier Selection and Testing task at LLNL. The selection will consist of several steps. First, preliminary, material-independent selection criteria will be established based on the performance goals for the container. Second, a variety of engineering materials will be evaluated against these criteria in a screening process to identify candidate materials. Third, information will be obtained on the performance of the candidate materials, and final selection criteria and quantitative weighting factors will be established based on the waste package design requirements. Finally, the candidate materials will be ranked against these criteria to determine whether they meet the mandated performance requirements, and to provide a comparative score to choose the material for advanced conceptual design activities. This document sets forth the preliminary container material selection criteria to be used in screening candidate materials. 5 refs

Developing emergency exercises for hazardous material transportation: process, documents and templates.

Science.gov (United States)

Crichton, Margaret; Kelly, Terence

2012-01-01

Multi-agency emergency exercises establish and reinforce relationships, and bring people from different areas together to work as a team, realise clear goals, understand roles and responsibilities, and get to know and respect each agency's strengths and weaknesses. However, despite the long-held belief in and respect for exercises in their provision of benefits to the individual and the organisation, there is little evidence of a consistent and clear process for exercise design, especially identifying the documents that may need to be completed to ensure efficient exercise preparation and performance. This paper reports the results of a project undertaken on behalf of the organisations that form the radioactive material transportation mutual-aid agreement, RADSAFE, to develop a standardised process to design emergency exercises. Three stages, from identifying the requirement for an exercise (Stage I), through to obtaining approval for operational orders (Stage II), then conducting a management review as part of the continuous improvement cycle (Stage III), were developed. Although designed for radioactive material transportation events, it is suggested that many of the factors within these three stages can be generalised for the design of exercises in other high-hazard industries.

DOE natural phenomenal hazards design and evaluation criteria

International Nuclear Information System (INIS)

Murray, R.C.; Nelson, T.A.; Short, S.A.; Kennedy, R.P.; Chander, H.; Hill, J.R.; Kimball, J.K.

1994-10-01

It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPH). Furthermore, DOE has established explicit goals of acceptable risk for NPH performance. As a result, natural phenomena hazard (earthquake, extreme wind, and flood) design and evaluation criteria for DOE facilities have been developed based on target probabilistic performance goals. These criteria include selection of design/evaluation NPH input from probabilistic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. For earthquake considerations, conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior, and by a seismic scale factor. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of qualitative expressions of acceptable behavior and of target quantitative probabilities that acceptable limits of behavior are maintained. The criteria are simple procedures but have a rigorous basis. This paper addresses DOE seismic design and evaluation criteria

Durability of Selected Membrane Materials when Exposed to Chlorine Gas

Energy Technology Data Exchange (ETDEWEB)

Eikeland, Marianne Soerflaten

2001-03-01

This thesis is focusing on the durability of selected membrane materials when exposed to chlorine gas in the temperature range 30-100{sup o}C. Studies of the changes of membrane separation properties and the mechanisms promoting these changes have been studied. The selected membrane materials were poly(dimethylsioxane) (PDMS), Fluorel, fluorosilicone, and blends of PDMS and Fluorel. The thesis is organised in seven chapters. The first chapter gives an introduction to the background of the work. The second chapter presents the theory for gas separation using dense rubbery membranes. The properties of the selected membrane materials are presented in chapter three. The fourth chapter describes degradation mechanisms for polymeric materials in general and for the selected membrane materials in particular. Presentation of the experimental work is given in chapter five, while the results with discussions are presented in chapter six. The conclusions and recommendations for further studies are given in chapter seven. Five appendixes are attached: Appendix A describes the calculations of permeability and solubility coefficients and the accuracy of the experimental measurements. Appendix B summarises the measured values in tables and Appendix C describes the analytical methods. Appendix D gives the properties of the gases used in the experiments. Appendix E is the article ''Durability of Poly(dimethylsiloxane) when Exposed to Chlorine Gas'', submitted to the Journal of Applied Polymer Science. Highly crosslinked PDMS was found to have an initial high permeability for chlorine gas and a high Cl{sub 2}/O{sub 2} selectivity. However when exposed to chlorine gas the permeability decreased significantly. Crosslinking of the PDMS polymer chain and chlorination of the polymer gave a denser polymer structure and thus lower permeability. Fluorel showed very low permeabilities and selectivities for the gases in question and was thus not interesting for this

75 FR 60017 - Hazardous Materials; Miscellaneous Amendments

Science.gov (United States)

2010-09-29

... prevent shifting or significant relative motion between the packages; that the consolidation bins be... display of the hazard identity (e.g., labels instead of placards) would support a small, more flexible... direction for all or part of their journey. Dynamic forces may shift an unsecured load or cause lading to...

Selection of refractory materials for pyrochemical processing

International Nuclear Information System (INIS)

Axler, K.M.; DePoorter, G.L.; Bagaasen, L.M.

1991-01-01

Several pyrochemical processing operations require containment materials that exhibit minimal chemical interactions with the system, good thermal shock resistance, and reusability. One example is Direct Oxide Reduction (DOR). DOR involves the conversion of PuO 2 to metal by an oxidation/reduction reaction with Ca metal. The reaction proceeds within a molten salt flux at temperatures above 800C. A combination of thermodynamics, system thermodynamic modeling, and experimental investigations are in use to select and evaluate potential containment materials

Safety Standard for Hydrogen and Hydrogen Systems: Guidelines for Hydrogen System Design, Materials Selection, Operations, Storage and Transportation. Revision

Science.gov (United States)

1997-01-01

The NASA Safety Standard, which establishes a uniform process for hydrogen system design, materials selection, operation, storage, and transportation, is presented. The guidelines include suggestions for safely storing, handling, and using hydrogen in gaseous (GH2), liquid (LH2), or slush (SLH2) form whether used as a propellant or non-propellant. The handbook contains 9 chapters detailing properties and hazards, facility design, design of components, materials compatibility, detection, and transportation. Chapter 10 serves as a reference and the appendices contained therein include: assessment examples; scaling laws, explosions, blast effects, and fragmentation; codes, standards, and NASA directives; and relief devices along with a list of tables and figures, abbreviations, a glossary and an index for ease of use. The intent of the handbook is to provide enough information that it can be used alone, but at the same time, reference data sources that can provide much more detail if required.

Perception and prevalence of work-related health hazards among health care workers in public health facilities in southern India.

Science.gov (United States)

Senthil, Arasi; Anandh, Balasubramanian; Jayachandran, Palsamy; Thangavel, Gurusamy; Josephin, Diana; Yamini, Ravindran; Kalpana, Balakrishnan

2015-01-01

Health care workers (HCWs) are exposed to occupational related health hazards. Measuring worker perception and the prevalence of these hazards can help facilitate better risk management for HCWs, as these workers are envisaged to be the first point of contact, especially in resource poor settings. To describe the perception of occupational health hazards and self-reported exposure prevalence among HCWs in Southern India. We used cross sectional design with stratified random sampling of HCWs from different levels of health facilities and categories in a randomly selected district in Southern India. Data on perception and exposure prevalence were collected using a structured interview schedule developed by occupational health experts and administered by trained investigators. A total of 482 HCWs participated. Thirty nine percent did not recognize work-related health hazards, but reported exposure to at least one hazard upon further probing. Among the 81·5% who reported exposure to biological hazard, 93·9% had direct skin contact with infectious materials. Among HCWs reporting needle stick injury, 70·5% had at least one in the previous three months. Ergonomic hazards included lifting heavy objects (42%) and standing for long hours (37%). Psychological hazards included negative feelings (20·3%) and verbal or physical abuse during work (20·5%). More than a third of HCWs failed to recognize work-related health hazards. Despite training in handling infectious materials, HCWs reported direct skin contact with infectious materials and needle stick injuries. RESULTS indicate the need for training oriented toward behavioral change and provision of occupational health services.

Hydrotreater/Distillation Column Hazard Analysis Report Rev. 2

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-04-15

This project Hazard and Risk Analysis Report contains the results of several hazard analyses and risk assessments. An initial assessment was conducted in 2012, which included a multi-step approach ranging from design reviews to a formal What-If hazard analysis. A second What-If hazard analysis was completed during February 2013 to evaluate the operation of the hydrotreater/distillation column processes to be installed in a process enclosure within the Process Development Laboratory West (PDL-West) facility located on the PNNL campus. The qualitative analysis included participation of project and operations personnel and applicable subject matter experts. The analysis identified potential hazardous scenarios, each based on an initiating event coupled with a postulated upset condition. The unmitigated consequences of each hazardous scenario were generally characterized as a process upset; the exposure of personnel to steam, vapors or hazardous material; a spray or spill of hazardous material; the creation of a flammable atmosphere; or an energetic release from a pressure boundary.

Pure zinc sulfide quantum dot as highly selective luminescent probe for determination of hazardous cyanide ion

International Nuclear Information System (INIS)

Shamsipur, Mojtaba; Rajabi, Hamid Reza

2014-01-01

A rapid and simple fluorescence method is presented for selective and sensitive determination of hazardous cyanide ion in aqueous solution based on functionalized zinc sulfide (ZnS) quantum dot (QD) as luminescent prob. The ultra-small ZnS QDs were synthesized using a chemical co-precipitation method in the presence of 2-mercaptoethanol (ME) as an efficient capping agent. The prepared pure ZnS QDs was applied as an optical sensor for determination of cyanide ions in aqueous solutions. ZnS nanoparticles have exhibited a strong fluorescent emission at about 424 nm. The fluorescence intensity of QDs is linearly proportional to the cyanide ion concentration in the range 2.44 × 10 −6 to 2.59 × 10 −5 M with a detection limit of 1.70 × 10 −7 M at pH 11. The designed fluorescent sensor possesses remarkable selectivity for cyanide ion over other anions such as Cl − , Br − , F − , I − , IO 3 − , ClO 4 − , BrO 3 − , CO 3 2− , NO 2 − , NO 3 − , SO 4 2− , S 2 O 4 2− , C 2 O 4 2− , SCN − , N 3 − , citrate and tartarate with negligible influences on the cyanide detection by fluorescence spectroscopy. - Highlights: • Preparation of functionalized ZnS quantum dots in aqueous media • Highly selective quantum dot based luminescent probe for determination of cyanide • Fast and sensitive determination of hazardous CN − by fluorescence quenching

Development of the photo catalytic materials for the purification and deodorization of hazardous wastes

International Nuclear Information System (INIS)

Hong, Gye Woon; Park, Ji Yeon; Jung, Choong Hwan; Kim, Weon Ju

1999-12-01

A hazardous material treatment system utilizing photochemical reaction is a new technology which does not produce any secondary pollutants after dissolving treatment because it is activated by solar photo energy. Photo catalysis reaction apparatus using photo catalytic reaction of TiO 2 was fabricated and installed to food waste treatment system for removing bad smell during treatment of food waste. Evolved gas was analysed by gas chromatograph and active carbon fiber sheet and yarn were used as adsorption media for photo catalysis in order to increase the effectiveness of filter system. (author)

Safety, health and environmental committee (JKSHE): Establishing chemical hazard management

International Nuclear Information System (INIS)

Shyen, A.K.S.; Noriah Mod Ali; Sangau, J.K.

2012-01-01

Most of the laboratories in Malaysian Nuclear Agency are using chemicals in their research activities. However, it is known that using of chemicals without proper knowledge especially on the material characteristics as well as safe handling procedure may cause great harm to the workers. Therefore, Safety, Health and Environmental Committee (JKSHE) sees the need to establish a good chemical hazard management to ensure that a safe and healthy workplace and environment is provided. One of the elements in chemical hazard management is to carry out Chemical Hazard Risk Assessment (CHRA). The assessment was done so that decision can be made on suitable control measures upon use of such chemicals, such as induction and training courses to be given to the workers and health surveillance activities that may be needed to protect the workers. For this, JKSHE has recommended to conduct CHRA for one of the laboratories at Secondary Standard Dosimetry Laboratory (SSDL) namely Film Dosimeter Processing Room (dark room) as the initial effort towards a better chemical hazard management. This paper presents the case study where CHRA was conducted to identify the chemical hazards at the selected laboratory, the adequacy of existing control measures and finally the recommendation for more effective control measures. (author)

Development of Knitted Materials Selection for Compression Underwear

Directory of Open Access Journals (Sweden)

Cheng Zhe

2017-06-01

Full Text Available The presented research deals with the development of comfortable male underwear taking into account the development of pattern block methods and the analysis of the relationships existing between the compression pressure, the knitted materials properties, and some push-up effects. The main aim of this study is to achieve the technical selection of the materials based on KES-FB evaluations.The ease value has been used as the main index to connect the structural design of underwear, on one hand, and the body sizes, on other hand. A “bodyshell” system for testing the soft tissue of male bodies by FlexiForce sensor has been implemented. The pressures under the shells at six different places on the male body with ease changing have been tested.The collected results including maximum-possible pressure and material tensile indexes measured thanks to KES-FB have been analyzed in order to find the most relevant indexes of the material properties. A mathematical equations based on relationships combining theoretical model with practical application have been established. These equations will be helpful for the consumers and designers to select “the suitable knitting materials for male underwear” and they can be used too in the perspective of parameterization in CAD, in order to improve product developments efficiency.

Hazardous materials in Aquatic environments of the Mississippi River basin. Quarterly project status report, 1 January 1994--30 March 1994

Energy Technology Data Exchange (ETDEWEB)

Abdelghani, A.

1994-06-01

Projects associated with this grant for studying hazardous materials in aquatic environments of the Mississippi River Basin are reviewed and goals, progress and research results are discussed. New, one-year initiation projects are described briefly.

Materials selection for process equipment in the Hanford waste vitrification plant

Energy Technology Data Exchange (ETDEWEB)

Elmore, M R; Jensen, G A

1991-07-01

The Hanford Waste Vitrification Plant (HWVP) is being designed to vitrify defense liquid high-level wastes and transuranic wastes stored at Hanford. The HWVP Functional Design Criteria (FDC) requires that materials used for fabrication of remote process equipment and piping in the facility be compatible with the expected waste stream compositions and process conditions. To satisfy FDC requirements, corrosion-resistant materials have been evaluated under simulated HWVP-specific conditions and recommendations have been made for HWVP applications. The materials recommendations provide to the project architect/engineer the best available corrosion rate information for the materials under the expected HWVP process conditions. Existing data and sound engineering judgement must be used and a solid technical basis must be developed to define an approach to selecting suitable construction materials for the HWVP. This report contains the strategy, approach, criteria, and technical basis developed for selecting materials of construction. Based on materials testing specific to HWVP and on related outside testing, this report recommends for constructing specific process equipment and identifies future testing needs to complete verification of the performance of the selected materials. 30 refs., 7 figs., 11 tabs.

Developing strategies to reduce the risk of hazardous materials transportation in iran using the method of fuzzy SWOT analysis

Directory of Open Access Journals (Sweden)

A. S. Kheirkhah

2009-12-01

Full Text Available An increase in hazardous materials transportation in Iran along with the industrial development and increase of resulted deadly accidents necessitate the development and implementation of some strategies to reduce these incidents. SWOT analysis is an efficient method for developing strategies, however, its structural problems, including a lack of prioritizing internal and external factors and inability to consider two sided factors reducing its performance in the situations where the number of internal and external factors affecting the risk of hazardous materials is relatively high and some factors are two sided in nature are presented in the article. Fuzzy SWOT analysis is a method the use of which helps with solving these problems and is the issue of employing an effective methodology. Also, the article compares the resulted strategies of the fuzzy method with the strategies developed following SWOT in order to show the relative supremacy of the new method.

Selection of plasma facing materials for ITER

International Nuclear Information System (INIS)

Ulrickson, M.; Barabash, V.; Chiocchio, S.

1996-01-01

ITER will be the first tokamak having long pulse operation using deuterium-tritium fuel. The problem of designing heat removal structures for steady state in a neutron environment is a major technical goal for the ITER Engineering Design Activity (EDA). The steady state heat flux specified for divertor components is 5 MW/m 2 for normal operation with transients to 15 MW/m 2 for up to 10 s. The selection of materials for plasma facing components is one of the major research activities. Three materials are being considered for the divertor; carbon fiber composites, beryllium, and tungsten. This paper discusses the relative advantages and disadvantages of these materials. The final section of plasma facing materials for the ITER divertor will not be made until the end of the EDA

Synopsis on selected hazard reports from Germany, Europe and international

International Nuclear Information System (INIS)

Atzl, Andreas; Lerch, Jennifer; Luxen, Johannes; Urban, Bert; Lackner, C.K.

2012-01-01

The Report covers the following issues in 6 sections (1) Introduction. (2) Procedures and methodology: selection of documents, qualitative pre-evaluation, quantitative analysis. (3) Results from the medical point of view: rush of patients in case of asymmetric threads; rush of casualties in case of natural disasters, medical care impairment in case of destroyed infrastructure; epidemics and pandemics; attacks or accidents in nuclear facilities; disturbance of the drinking water supply; CBRN (chemical, biological, radiation, nuclear) attacks. (4) Results from the point of view of environmental and engineering science: overview, asymmetric threat, climatic change, D (information and communication technologies) hazards; public supply in case of emergency. (5) Results from the point of view of social science: overview on the matrix; vulnerabilities, institutional challenges, self-protection, information and warning of the public. (6) Conclusions: dominance of asymmetric threat and need of systemic approaches in civil defense; supply of the public and critical infrastructures, transformation processes and challenges in civil defense; quality of documents and need of additional research on emergency protection.

Environmental materials and interfaces

International Nuclear Information System (INIS)

1991-11-01

A workshop that explored materials and interfaces research needs relevant to national environmental concerns was conducted at Pacific Northwest Laboratory. The purposes of the workshop were to refine the scientific research directions being planned for the Materials and Interface Program in the Molecular Science Research Center (MSRC) and further define the research and user equipment to the included as part of the proposed Environmental and Molecular Science Laboratory (EMSL). Three plenary information sessions served to outline the background, objectives, and status of the MSRC and EMSL initiatives; selected specific areas with environmentally related materials; and the status of capabilities and facilities planned for the EMSL. Attention was directed to four areas where materials and interface science can have a significant impact on prevention and remediation of environmental problems: in situ detection and characterization of hazardous wastes (sensors), minimization of hazardous waste (separation membranes, ion exchange materials, catalysts), waste containment (encapsulation and barrier materials), and fundamental understanding of contaminant transport mechanisms. During all other sessions, the participants were divided into three working groups for detailed discussion and the preparation of a written report. The working groups focused on the areas of interface structure and chemistry, materials and interface stability, and materials synthesis. These recommendations and suggestions for needed research will be useful for other researchers in proposing projects and for suggesting collaborative work with MSRC researchers. 1 fig

Hazard screening application guide

International Nuclear Information System (INIS)

1992-06-01

The basic purpose of hazard screening is to group precesses, facilities, and proposed modifications according to the magnitude of their hazards so as to determine the need for and extent of follow on safety analysis. A hazard is defined as a material, energy source, or operation that has the potential to cause injury or illness in human beings. The purpose of this document is to give guidance and provide standard methods for performing hazard screening. Hazard screening is applied to new and existing facilities and processes as well as to proposed modifications to existing facilities and processes. The hazard screening process evaluates an identified hazards in terms of the effects on people, both on-site and off-site. The process uses bounding analyses with no credit given for mitigation of an accident with the exception of certain containers meeting DOT specifications. The process is restricted to human safety issues only. Environmental effects are addressed by the environmental program. Interfaces with environmental organizations will be established in order to share information

HMPT: Hazardous Waste Transportation Live 27928, Test 27929

Energy Technology Data Exchange (ETDEWEB)

Simpson, Lewis Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-03-17

HMPT: Hazardous Waste Transportation (Live 27928, suggested one time and associated Test 27929, required initially and every 36 months) addresses the Department of Transportation (DOT) function-specific training requirements of the hazardous materials packagings and transportation (HMPT) Los Alamos National Laboratory (LANL) lab-wide training. This course addresses the requirements of the DOT that are unique to hazardous waste shipments. Appendix B provides the Title 40 Code of Federal Regulations (CFR) reference material needed for this course.

Incidents with hazardous radiation sources; Zwischenfaelle mit gefaehrlichen Strahlenquellen

Energy Technology Data Exchange (ETDEWEB)

Schoenhacker, Stefan [Bundesministerium fuer Inneres, Traiskirchen (Austria). Abt. 1/9 - Zivilschutzschule

2016-07-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

A new approach to hazardous materials transportation risk analysis: decision modeling to identify critical variables.

Science.gov (United States)

Clark, Renee M; Besterfield-Sacre, Mary E

2009-03-01

We take a novel approach to analyzing hazardous materials transportation risk in this research. Previous studies analyzed this risk from an operations research (OR) or quantitative risk assessment (QRA) perspective by minimizing or calculating risk along a transport route. Further, even though the majority of incidents occur when containers are unloaded, the research has not focused on transportation-related activities, including container loading and unloading. In this work, we developed a decision model of a hazardous materials release during unloading using actual data and an exploratory data modeling approach. Previous studies have had a theoretical perspective in terms of identifying and advancing the key variables related to this risk, and there has not been a focus on probability and statistics-based approaches for doing this. Our decision model empirically identifies the critical variables using an exploratory methodology for a large, highly categorical database involving latent class analysis (LCA), loglinear modeling, and Bayesian networking. Our model identified the most influential variables and countermeasures for two consequences of a hazmat incident, dollar loss and release quantity, and is one of the first models to do this. The most influential variables were found to be related to the failure of the container. In addition to analyzing hazmat risk, our methodology can be used to develop data-driven models for strategic decision making in other domains involving risk.

Design of lightweight multi-material automotive bodies using new material performance indices of thin-walled beams for the material selection with crashworthiness consideration

International Nuclear Information System (INIS)

Cui, Xintao; Zhang, Hongwei; Wang, Shuxin; Zhang, Lianhong; Ko, Jeonghan

2011-01-01

Currently, automotive bodies are constructed usually using a single material, e.g. steel or aluminum. Compared to single-material automotive bodies, multi-material automotive bodies allow optimal material selection in each structural component for higher product performance and lower cost. This paper presents novel material performance indices and procedures developed to guide systematic material selection for multi-material automotive bodies. These new indices enable to characterize the crashworthiness performance of complex-shaped thin-walled beams in multi-material automotive bodies according to material types. This paper also illustrates the application of these performance indices and procedures by designing a lightweight multi-material automotive body. These procedures will help to design a lightweight and affordable body favored by the automotive industry, thus to reduce fuel consumption and greenhouse gas emissions.

Materials selection in micromechanical design: an application of the Ashby approach

OpenAIRE

Srikar, V.T.; Spearing, S.M.

2003-01-01

The set of materials available to microsystems designers is rapidly expanding. Techniques now exist to introduce and integrate a large number of metals, alloys, ceramics, glasses, polymers, and elastomers into microsystems, motivating the need for a rational approach for materials selection in microsystems design. As a step toward such an approach, we focus on the initial stages of materials selection for micromechanical structures with minimum feature sizes greater than 1 /spl mu/m. The vari...

Assessment and Selection of Materials for Melbourne City Council House 2

Directory of Open Access Journals (Sweden)

Dominique Hes

2012-11-01

Full Text Available This paper highlights the role of material selection in the development and contribution toward environmental excellence in the building project Council House 2 (CH2. The paper focuses on the assessment of material and the strategies used by the design team in CH2to ensure the best environmental result. The paper then goes on to explore in a case study the application of these strategies in the selection and specification of concrete on CH2. The purpose of the paper is to explore the difficulties and rewards of careful research of manufacturers' claims and the relative benefits of different materials. The paper concludes that the process of material selection adopted on this project has increased the education of architects and manufacturers alike as well as being environmentally beneficial.

Developing high-risk scenarios and countermeasure ideas for mitigation of hazardous materials incidents

International Nuclear Information System (INIS)

Russell, E.R. Sr.

1991-01-01

Kansas State University (KSU) conducted a comprehensive study of the development of a set of prioritized, extreme-risk scenarios, the development of a set of feasible, practical and implementable protective systems, and a report to summarize guidelines on the use of these protective systems to mitigate potential, extreme-risk situations that could occur during the transport of hazardous materials (Hazmat) on our highway system. This paper covers the methodology used to compete the first tow objectives with use of a state's panel. The research study was limited to materials (such as LNG, propane, gasoline, etc.) spilled within the highway system. It focused on potential risks which would result in severe, long-term, permanent, irreparable or catastrophic consequences, and existing technology and state-of-the-art knowledge for development of protective systems to mitigate these consequences. The protective systems within the scope of this study were systems constructed or physically incorporated into the highway system or modifications thereto

Tulane/Xavier University hazardous materials in aquatic environments of the Mississippi River Basin. Annual technical report, January 1--December 31, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-02

Tulane and Xavier Universities have singled out the environment as a major strategic focus for research and training for now and beyond the year 2000. In 1989, the Tulane/Xavier Center for Bioenvironmental Research (CBR) was established as the umbrella organization which coordinates environmental research at both universities. In December, 1992, the Tulane/Xavier CBR was awarded a five year grant to study pollution in the Mississippi River system. The Hazardous Materials in Aquatic Environments of the Mississippi River Basin project is a broad research and education program aimed at elucidating the nature and magnitude of toxic materials that contaminate aquatic environments of the Mississippi River Basin. Studies include defining the complex interactions that occur during the transport of contaminants, the actual and potential impact on ecological systems and health, and the mechanisms through which these impacts might be remediated. The Mississippi River Basin represents a model system for analyzing and solving contamination problems that are found in aquatic systems world-wide. Summaries which describe objectives, goals, and accomplishments are included on ten collaborative cluster projects, two education projects, and six initiation projects. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Basic Thermal Parameters of Selected Foods and Food Raw Materials

Directory of Open Access Journals (Sweden)

Monika Božiková

2017-01-01

Full Text Available In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of thermal parameters measurement for various foods and food raw materials as: granular materials – corn flour and wheat flour; fruits, vegetables and fruit products – grated apple, dried apple and apple juice; liquid materials – milk, beer etc. Measurements were performed in two temperature ranges according to the character of examined material. From graphical relations of thermophysical parameter is evident, that thermal conductivity and diffusivity increases with temperature and moisture content linearly, only for granular materials were obtained non‑linear dependencies. Results shows, that foods and food raw materials have different thermal properties, which are influenced by their type, structure, chemical and physical properties. From presented results is evident, that basic thermal parameters are important for material quality detection in food industry.

Solidification as low cost technology prior to land filling of industrial hazardous waste sludge.

Science.gov (United States)

El-Sebaie, O; Ahmed, M; Ramadan, M

2000-01-01

The aim of this study is to stabilize and solidify two different treated industrial hazardous waste sludges, which were selected from factories situated close to Alexandria. They were selected to ensure their safe transportation and landfill disposal by reducing their potential leaching of hazardous elements, which represent significant threat to the environment, especially the quality of underground water. The selected waste sludges have been characterized. Ordinary Portland Cement (OPC), Cement Kiln Dust (CKD) from Alexandria Portland Cement Company, and Calcium Sulphate as a by-product from the dye industry were used as potential solidification additives to treat the selected treated waste sludges from tanning and dyes industry. Waste sludges as well as the solidified wastes have been leach-tested, using the General Acid Neutralization Capacity (GANC) procedure. Concentration of concerning metals in the leachates was determined to assess changes in the mobility of major contaminants. The treated tannery waste sludge has an acid neutralization capacity much higher than that of the treated dyes waste sludge. Experiment results demonstrated the industrial waste sludge solidification mix designs, and presented the reduction of contaminant leaching from two types of waste sludges. The main advantages of solidification are that it is simple and low cost processing which includes readily available low cost solidification additives that will convert industrial hazardous waste sludges into inert materials.

Significance of ITER IWS Material Selection and Qualification

Science.gov (United States)

Mehta, Bhoomi K.; Raval, Jigar; Maheshwari, Abha; Laad, Rahul; Singh, Gurlovleen; Pathak, Haresh

2017-04-01

In-Wall Shielding (IWS) is one of the important components of ITER Vacuum Vessel (VV) which fills the space between double walls of VV with cooling water. Procurement Arrangement (PA) for IWS has been signed with Indian Domestic Agency (INDA). Procurement of IWS materials, fabrication of IWS blocks and its delivery to respective Domestic Agency (DA) and ITER Organization (IO) are the main scope of this PA. Hence, INDIA is the only country which is contributing to VV IWS among all seven ITER partners. The main functions of the IWS are to provide Neutron Shielding with blanket, VV shells and water during plasma operations and to reduce ripple of the Toroidal Magnetic Field. To meet these functional requirements IWS blocks are made up of special materials (Borated Steels SS304 B4 & SS304 B7, Ferritic Steels SS 430, Austenitic Steel SS 316 L (N)-IG, XM-19 and Inconel-625) which are qualified, reliable and traceable for the design assessment. The choice of these materials has a significant influence on performance, maintainability, licensing, detailed design parameters and waste disposal. The main reasons for the materials selected for IWS are its high mechanical strength at operating temperatures, water chemistry properties, excellent fabrication characteristics and low cost relative to other similar materials. All the materials are qualified with respect to their respective codes (ASTM/EN standards with additional requirements as described in RCC-MR code 2007) and ITER requirements. Agreed Notified Body (ANB) has control conformity of materials certificates with approved material specification and traceability procedure for Safety Important Component (SIC). The procurement strategy for all the IWS materials has been developed in close collaboration with IO, ANB and Industries as per Product Procurement Specification (PPS). The R&D for sample, bulk material production, testing, inspection and handling as required are carried out by IN DA and IO. At present almost all

Device for Detection of Explosives, Nuclear and Other Hazardous Materials in Luggage and Cargo Containers

International Nuclear Information System (INIS)

Kuznetsov, Andrey; Evsenin, Alexey; Osetrov, Oleg; Vakhtin, Dmitry; Gorshkov, Igor

2009-01-01

Device for detection of explosives, radioactive and heavily shielded nuclear materials in luggage and cargo containers based on Nanosecond Neutron Analysis/Associated Particles Technique (NNA/APT) is under construction. Detection module consists of a small neutron generator with built-in position-sensitive detector of associated alpha-particles, and several scintillator-based gamma-ray detectors. Explosives and other hazardous chemicals are detected by analyzing secondary high-energy gamma-rays from reactions of fast neutrons with materials inside a container. The same gamma-ray detectors are used to detect unshielded radioactive and nuclear materials. An array of several neutron detectors is used to detect fast neutrons from induced fission of nuclear materials. Coincidence and timing analysis allows one to discriminate between fission neutrons and scattered probing neutrons. Mathematical modeling by MCNP5 and MCNP-PoliMi codes was used to estimate the sensitivity of the device and its optimal configuration. Comparison of the features of three gamma detector types--based on BGO, NaI and LaBr 3 crystals is presented.

Device for Detection of Explosives, Nuclear and Other Hazardous Materials in Luggage and Cargo Containers

Science.gov (United States)

Kuznetsov, Andrey; Evsenin, Alexey; Gorshkov, Igor; Osetrov, Oleg; Vakhtin, Dmitry

2009-12-01

Device for detection of explosives, radioactive and heavily shielded nuclear materials in luggage and cargo containers based on Nanosecond Neutron Analysis/Associated Particles Technique (NNA/APT) is under construction. Detection module consists of a small neutron generator with built-in position-sensitive detector of associated alpha-particles, and several scintillator-based gamma-ray detectors. Explosives and other hazardous chemicals are detected by analyzing secondary high-energy gamma-rays from reactions of fast neutrons with materials inside a container. The same gamma-ray detectors are used to detect unshielded radioactive and nuclear materials. An array of several neutron detectors is used to detect fast neutrons from induced fission of nuclear materials. Coincidence and timing analysis allows one to discriminate between fission neutrons and scattered probing neutrons. Mathematical modeling by MCNP5 and MCNP-PoliMi codes was used to estimate the sensitivity of the device and its optimal configuration. Comparison of the features of three gamma detector types—based on BGO, NaI and LaBr3 crystals is presented.

Preliminary Hazard Classification for the 105-B Reactor

International Nuclear Information System (INIS)

Kerr, N.R.

1997-08-01

This document summarizes the inventories of radioactive and hazardous materials present within the 105-B Reactor and uses the inventory information to determine the preliminary hazard classification for the surveillance and maintenance activities of the facility. The result of this effort was the preliminary hazard classification for the 105-B Building surveillance and maintenance activities. The preliminary hazard classification was determined to be Nuclear Category 3. Additional hazard and accident analysis will be documented in a separate report to define the hazard controls and final hazard classification

Decision support for environmental management of industrial non-hazardous secondary materials: New analytical methods combined with simulation and optimization modeling.

Science.gov (United States)

Little, Keith W; Koralegedara, Nadeesha H; Northeim, Coleen M; Al-Abed, Souhail R

2017-07-01

Non-hazardous solid materials from industrial processes, once regarded as waste and disposed in landfills, offer numerous environmental and economic advantages when put to beneficial uses (BUs). Proper management of these industrial non-hazardous secondary materials (INSM) requires estimates of their probable environmental impacts among disposal as well as BU options. The U.S. Environmental Protection Agency (EPA) has recently approved new analytical methods (EPA Methods 1313-1316) to assess leachability of constituents of potential concern in these materials. These new methods are more realistic for many disposal and BU options than historical methods, such as the toxicity characteristic leaching protocol. Experimental data from these new methods are used to parameterize a chemical fate and transport (F&T) model to simulate long-term environmental releases from flue gas desulfurization gypsum (FGDG) when disposed of in an industrial landfill or beneficially used as an agricultural soil amendment. The F&T model is also coupled with optimization algorithms, the Beneficial Use Decision Support System (BUDSS), under development by EPA to enhance INSM management. Published by Elsevier Ltd.

Selective Postevent Review and Children's Memory for Nonreviewed Materials

Science.gov (United States)

Conroy, R.; Salmon, K.

2005-01-01

Two experiments investigated the impact of selective postevent questioning on children's memory for nonreviewed materials. In both experiments, children participated in a series of novel activities. Children in the selective-review condition were subsequently questioned about half of these and comparisons were made to memory in a no-review…

Information resources and material selection in bonded restorations among Korean dentists.

Science.gov (United States)

Chang, Juhea; Kim, Hae-Young; Cho, Byeong Hoon; Lee, In Bog; Son, Ho Hyun

2009-12-01

To elucidate how dentists access knowledge sources when choosing adhesive agents for bonded restoration and whether these resources influenced the selection of materials. A national survey was carried out involving dentists in South Korea. The questionnaire included the status of the operator, clinical techniques, and materials. A total of 12,193 e-mails were distributed, 2632 were opened by recipients, and 840 responses were collected. For primary information resources in material selection, 55.8% (n = 469) of the responders mentioned continuing education. This selection criteria varied according to the working status of the clinician (p choice of bonding system was influenced by of the length of the career (p < 0.0001), and the preferred bonding systems differed according to the source of the information (p = 0.035). The popular bonding systems were not ranked according to the bonding strategy, but a preference was found for specific brands or manufacturers. To decrease the confusion of clinicians related to the selection of bonding materials, evidence-based guidelines need to be comprehensibly organized and efficiently approached in clinics.

Hydrothermal Liquefaction Treatment Preliminary Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P.; Wagner, Katie A.

2015-08-31

A preliminary hazard assessment was completed during February 2015 to evaluate the conceptual design of the modular hydrothermal liquefaction treatment system. The hazard assessment was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. This analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public.

Treatment of hazardous metals by in situ vitrification

International Nuclear Information System (INIS)

Koegler, S.S.; Buelt, J.L.

1989-02-01

Soils contaminated with hazardous metals are a significant problem to many Defense Program sites. Contaminated soils have ranked high in assessments of research and development needs conducted by the Hazardous Waste Remedial Action Program (HAZWRAP) in FY 1988 and FY 1989. In situ vitrification (ISV) is an innovative technology suitable for stabilizing soils contaminated with radionuclides and hazardous materials. Since ISV treats the material in place, it avoids costly and hazardous preprocessing exhumation of waste. In situ vitrification was originally developed for immobilizing radioactive (primarily transuranic) soil constituents. Tests indicate that it is highly useful also for treating other soil contaminants, including hazardous metals. The ISV process produces an environmentally acceptable, highly durable glasslike product. In addition, ISV includes an efficient off-gas treatment system that eliminates noxious gaseous emissions and generates minimal hazardous byproducts. This document reviews the Technical Basis of this technology. 5 refs., 7 figs., 2 tabs

The Selection of Materials for Roller Chains From The Perspective Of Manufacturing Process

Directory of Open Access Journals (Sweden)

Rahmat Saptono

2010-10-01

Full Text Available The selection of materials for an engineering component is not only requested by its design function and shape, but also the sequence through which it is manufactured. The manufacturing operation of roller chains involves drawing and trimming processes aimed at producing semi-finished chain drives component with a well-standardized dimension. In addition to final combination of properties required by design constraints, the ability of materials to be formed into a desired shape and geometry without failure is also critical. The objective of materials selection should therefore involve additional attributes that are not typically  accommodated by the standard procedure of materials selection. The present paper deals with the selection of materials for roller chains from the perspective of manufacturing process. Ears and un-uniform wall thickness have been identified as a key problem in the mass production of component. Provided all process parameters were established, the  anisotropy factor of materials is critical. Simulative test can be reasonably used to obtain material performance indices that can be added up to the standard procedure of material selection. Of three commercially available steel grades evaluated with regard to the criteria defined, one grade is more suitable for the present objective.

An integrated approach towards future ballistic neck protection materials selection.

Science.gov (United States)

Breeze, John; Helliker, Mark; Carr, Debra J

2013-05-01

Ballistic protection for the neck has historically taken the form of collars attached to the ballistic vest (removable or fixed), but other approaches, including the development of prototypes incorporating ballistic material into the collar of an under body armour shirt, are now being investigated. Current neck collars incorporate the same ballistic protective fabrics as the soft armour of the remaining vest, reflecting how ballistic protective performance alone has historically been perceived as the most important property for neck protection. However, the neck has fundamental differences from the thorax in terms of anatomical vulnerability, flexibility and equipment integration, necessitating a separate solution from the thorax in terms of optimal materials selection. An integrated approach towards the selection of the most appropriate combination of materials to be used for each of the two potential designs of future neck protection has been developed. This approach requires evaluation of the properties of each potential material in addition to ballistic performance alone, including flexibility, mass, wear resistance and thermal burden. The aim of this article is to provide readers with an overview of this integrated approach towards ballistic materials selection and an update of its current progress in the development of future ballistic neck protection.

Adsorption and Detection of Hazardous Trace Gases by Metal-Organic Frameworks.

Science.gov (United States)

Woellner, Michelle; Hausdorf, Steffen; Klein, Nicole; Mueller, Philipp; Smith, Martin W; Kaskel, Stefan

2018-06-19

The quest for advanced designer adsorbents for air filtration and monitoring hazardous trace gases has recently been more and more driven by the need to ensure clean air in indoor, outdoor, and industrial environments. How to increase safety with regard to personal protection in the event of hazardous gas exposure is a critical question for an ever-growing population spending most of their lifetime indoors, but is also crucial for the chemical industry in order to protect future generations of employees from potential hazards. Metal-organic frameworks (MOFs) are already quite advanced and promising in terms of capacity and specific affinity to overcome limitations of current adsorbent materials for trace and toxic gas adsorption. Due to their advantageous features (e.g., high specific surface area, catalytic activity, tailorable pore sizes, structural diversity, and range of chemical and physical properties), MOFs offer a high potential as adsorbents for air filtration and monitoring of hazardous trace gases. Three advanced topics are considered here, in applying MOFs for selective adsorption: (i) toxic gas adsorption toward filtration for respiratory protection as well as indoor and cabin air, (ii) enrichment of hazardous gases using MOFs, and (iii) MOFs as sensors for toxic trace gases and explosives. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

HAZARDOUS MATERIALS IN AQUATIC ENVIRONMENTS OF THE MISSISSIPPI RIVER BASIN

Energy Technology Data Exchange (ETDEWEB)

John A. McLachlan

2003-12-01

In December 1992, the CBR was awarded a five-year grant of $25M from the US Department of Energy Office of Environmental Management (DOE-EM) to study pollution in the Mississippi River system. The ''Hazardous Materials in Aquatic Environments of the Mississippi River Basin'' project was an interdisciplinary, collaborative research and education project aimed at elucidating the nature and magnitude of toxic materials that contaminate aquatic environments. This project funded 15 collaborative cluster multi-year projects and 41 one-year initiation projects out of 165 submitted research proposals. This project was carried out by 134 research and technical support faculty from Xavier University (School of Arts and Sciences, and College of Pharmacy) and Tulane University (Schools of Liberal Arts and Sciences, Engineering, Medicine, and Public Health and Tropical Medicine), and 173 publications and 140 presentations were produced. More than 100 graduate and undergraduate students were trained through these collaborative cluster and initiation research projects. Nineteen Tulane graduate students received partial funding to conduct their own competitively-chosen research projects, and 28 Xavier undergraduate LIFE Scholars and 30 LIFE Interns were supported with DOE funding to conduct their mentored research projects. Studies in this project have defined: (1) the complex interactions that occur during the transport of contaminants, (2) the actual and potential impact on ecological systems and health, and (3) the mechanisms through which these impacts might be remediated. The bayou and spoil banks of Bayou Trepagnier were mapped and analyzed in terms of risks associated with the levels of hydrocarbons and metals at specific sample sites. Data from contaminated sample sites have been incorporated into a large database and used in GIS analyses to track the fate and transport of heavy metals from spoil banks into the surrounding marsh. These data are crucial

Support for the Delisting of Decontaminated Liquid Chemical Surety Materials as Listed Hazardous Waste from Specific Sources (STATE) MD02 in COMAR 10.51.02.16-1

Science.gov (United States)

1988-11-01

radiography , and clear’y stated in I 160.81(c), EPA test systems without also bearing the handling of biohazardous materials." considers the inclusion of this...treatment, and necropsy, histology, radiography , and proper conduct of the study. control of disease. Additionally, EPA handling of bimazardous materials...inhalation Pa1 Page 8-77 hazard test reccgnizes that both volatility and toxicity affect the hazard potential in the workplace . To address these two

Considerations in selecting tubing materials for CANDU steam generators

International Nuclear Information System (INIS)

Hemmings, R.L.

1978-01-01

Corrosion resistance is the major consideration in selecting tubing material for CANDU steam generators. Corrosion, and additional considerations, lead to the following steam generator tubing material recommendations: for CANDU-BPHWR's (boiling pressurized heavy water reactors) low-cobalt Incoloy-800; for CANDU-PHWR's (pressurized, non-boiling, heavy water reactors), low-cobalt Monel-400

Hazards to nuclear plants from surface traffic accidents

International Nuclear Information System (INIS)

Hornyik, K.

1975-01-01

Analytic models have been developed for evaluating hazards to nuclear plants from hazardous-materials accidents in the vicinity of the plant. In particular, these models permit the evaluation of hazards from such accidents occurring on surface traffic routes near the plant. The analysis uses statistical information on accident rates, traffic frequency, and cargo-size distribution along with parameters describing properties of the hazardous cargo, plant design, and atmospheric conditions, to arrive at a conservative estimate of the annual probability of a catastrophic event. Two of the major effects associated with hazardous-materials accidents, explosion and release of toxic vapors, are treated by a common formalism which can be readily applied to any given case by means of a graphic procedure. As an example, for a typical case it is found that railroad shipments of chlorine in 55-ton tank cars constitute a greater hazard to a nearby nuclear plant than equally frequent rail shipments of explosives in amounts of 10 tons. 11 references. (U.S.)

Seismic assessment of selected buildings and equipment contents of a DOE facility in UBC zone 2A

International Nuclear Information System (INIS)

Tong, W.H.; Deneff, C.; Griffin, M.J.

1991-01-01

A preliminary seismic risk assessment for selected buildings and representative equipment contents in Allied-Signal Kansas City Division was performed to identify potential seismic hazard and weakness. The site is located in the Uniform Building Code Zone 2A. The selected building structures were constructed between 1940s to 1980s. The performance goal was to qualitatively assess the potential for loss of toxic or hazardous materials and injury to plant personnel due to an earthquake event

Results of Testing the Relative Oxidizing Hazard of Wipes and KMI Zeolite

Energy Technology Data Exchange (ETDEWEB)

Ams, Bridget Elaine [Los Alamos National Laboratory

2017-05-09

This report includes the results from testing performed on the relative oxidizing hazard of a number of organic sorbing wipe materials, as well as KMI zeolite. These studies were undertaken to address a need by the Los Alamos National Laboratory (LANL) Hazardous Materials Management group, which requires a material that can sorb small spills in a glovebox without creating a disposal hazard due to the potential for oxidation reactions, as requested in Request for Testing of Wipes and Zeolite for Los Alamos National Laboratory Hazardous Materials Group (NPl-7) (NPl-7-17-002) and Request for Testing of Chamois Material for Los Alamos National Laboratory Hazardous Materials Group (NPl-7) (NPl-7-17-005). This set oftests is a continuation of previous testing described in Results from Preparation and Testing of Sorbents Mixed with (DWT-RPT-003), which provided data for the Waste Isolation Pilot Plant's Basis of Knowledge. The Basis of Knowledge establishes criteria for evaluating transuranic (TRU) waste that contains oxidizing chemicals.

The Selection of Bridge Materials Utilizing the Analytical Hierarchy Process

Science.gov (United States)

Robert L. Smith; Robert J. Bush; Daniel L. Schmoldt

1997-01-01

Effective decisions on the use of natural resources often require the input of many individuals. Determining how specific criteria affect the selection of materials can lead to better utilization of raw materials. Concrete, steel, and timber represent over 98% of the materials used for bridge construction in the United States. Highway officials must often consider...

Catalytic Destruction of a Surrogate Organic Hazardous Air Pollutant as a Potential Co-benefit for Coal-fired Selective Catalyst Reduction Systems

Science.gov (United States)

Catalytic destruction of benzene (C6H6), a surrogate for organic hazardous air pollutants (HAPs) produced from coal combustion, was investigated using a commercial selective catalytic reduction (SCR) catalyst for evaluating the potential co-benefit of the SCR technology for reduc...

Report 6: Guidance document. Man-made hazards and Accidental Aircraft Crash hazards modelling and implementation in extended PSA

International Nuclear Information System (INIS)

Kahia, S.; Brinkman, H.; Bareith, A.; Siklossy, T.; Vinot, T.; Mateescu, T.; Espargilliere, J.; Burgazzi, L.; Ivanov, I.; Bogdanov, D.; Groudev, P.; Ostapchuk, S.; Zhabin, O.; Stojka, T.; Alzbutas, R.; Kumar, M.; Nitoi, M.; Farcasiu, M.; Borysiewicz, M.; Kowal, K.; Potempski, S.

2016-01-01

The goal of this report is to provide guidance on practices to model man-made hazards (mainly external fires and explosions) and accidental aircraft crash hazards and implement them in extended Level 1 PSA. This report is a joint deliverable of work package 21 (WP21) and work package 22 (WP22). The general objective of WP21 is to provide guidance on all of the individual hazards selected at the first ASAMPSA-E End Users Workshop (May 2014, Uppsala, Sweden). The objective of WP22 is to provide the solutions for purposes of different parts of man-made hazards Level 1 PSA fulfilment. This guidance is focusing on man-made hazards, namely: external fires and explosions, and accidental aircraft crash hazards. Guidance developed refers to existing guidance whenever possible. The initial part of guidance (WP21 part) reflects current practices to assess the frequencies for each type of hazards or combination of hazards (including correlated hazards) as initiating event for PSAs. The sources and quality of hazard data, the elements of hazard assessment methodologies and relevant examples are discussed. Classification and criteria to properly assess hazard combinations as well as examples and methods for assessment of these combinations are included in this guidance. In appendixes additional material is presented with the examples of practical approaches to aircraft crash and man-made hazard. The following issues are addressed: 1) Hazard assessment methodologies, including issues related to hazard combinations. 2) Modelling equipment of safety related SSC, 3) HRA, 4) Emergency response, 5) Multi-unit issues. Recommendations and also limitations, gaps identified in the existing methodologies and a list of open issues are included. At all stages of this guidance and especially from an industrial end-user perspective, one must keep in mind that the development of man-made hazards probabilistic analysis must be conditioned to the ability to ultimately obtain a representative risk

An Augmented Common Weight Data Envelopment Analysis for Material Selection in High-tech Industries

Directory of Open Access Journals (Sweden)

Iman Shokr

2016-08-01

Full Text Available Material selection is a challenging issue in manufacturing processes while the inappropriate selected material may lead to fail the manufacturing process or end user experience especially in high-tech industries such as aircraft and shipping. Every material has different quantitative and qualitative criteria which should be considered simultaneously when assessing and selecting the right material. A weighted linear optimization method (WLOM in the class of data envelopment analysis which exists in literature is adopted to address material selection problem while accounting for both qualitative and quantitative criteria. However, it is demonstrated the adopted WLOM method is not able to produce a full ranking vector for the material selection problems borrowed from the literature. Thus, an augmented common weight data envelopment analysis model (ACWDEA is developed in this paper with the aim of eliminating deficiencies of WLOM model. The proposed ACWDEA is able to produce full ranking vector in decision making problems with less computational complexities in superior to the WLOM. Two material selection problems are solved and results are compared with WLOM and previous methods. Finally, the robustness and effectiveness of the proposed ACWDEA method are evaluated through Spearman’s correlation tests.

Toxic hazards of underground excavation

International Nuclear Information System (INIS)

Smith, R.; Chitnis, V.; Damasian, M.

1982-09-01

Inadvertent intrusion into natural or man-made toxic or hazardous material deposits as a consequence of activities such as mining, excavation or tunnelling has resulted in numerous deaths and injuries in this country. This study is a preliminary investigation to identify and document instances of such fatal or injurious intrusion. An objective is to provide useful insights and information related to potential hazards due to future intrusion into underground radioactive-waste-disposal facilities. The methodology used in this study includes literature review and correspondence with appropriate government agencies and organizations. Key categories of intrusion hazards are asphyxiation, methane, hydrogen sulfide, silica and asbestos, naturally occurring radionuclides, and various mine or waste dump related hazards

Toxic hazards of underground excavation

Energy Technology Data Exchange (ETDEWEB)

Smith, R.; Chitnis, V.; Damasian, M.; Lemm, M.; Popplesdorf, N.; Ryan, T.; Saban, C.; Cohen, J.; Smith, C.; Ciminesi, F.

1982-09-01

Inadvertent intrusion into natural or man-made toxic or hazardous material deposits as a consequence of activities such as mining, excavation or tunnelling has resulted in numerous deaths and injuries in this country. This study is a preliminary investigation to identify and document instances of such fatal or injurious intrusion. An objective is to provide useful insights and information related to potential hazards due to future intrusion into underground radioactive-waste-disposal facilities. The methodology used in this study includes literature review and correspondence with appropriate government agencies and organizations. Key categories of intrusion hazards are asphyxiation, methane, hydrogen sulfide, silica and asbestos, naturally occurring radionuclides, and various mine or waste dump related hazards.

Criteria for the selection of PEC primary circuit structural material

International Nuclear Information System (INIS)

Antoni, R.; Brunori, G.; Maesa, S.; Scibona, G.; Tomassetti, G.

1977-01-01

The choice of the structural materials is generally a compromise between the project requirements, the characteristics (mechanical and environmental) of the materials and the available technology to construct the various parts of the components. The criteria of selection of structural materials for the primary circuit of fast reactor are reported. The criteria concern both general and utilization aspects

A review of accidents, prevention and mitigation options related to hazardous gases

International Nuclear Information System (INIS)

Fthenakis, V.M.

1993-05-01

Statistics on industrial accidents are incomplete due to lack of specific criteria on what constitutes a release or accident. In this country, most major industrial accidents were related to explosions and fires of flammable materials, not to releases of chemicals into the environment. The EPA in a study of 6,928 accidental releases of toxic chemicals revealed that accidents at stationary facilities accounted for 75% of the total number of releases, and transportation accidents for the other 25%. About 7% of all reported accidents (468 cases) resulted in 138 deaths and 4,717 injuries ranging from temporary respiratory problems to critical injuries. In-plant accidents accounted for 65% of the casualties. The most efficient strategy to reduce hazards is to choose technologies which do not require the use of large quantities of hazardous gases. For new technologies this approach can be implemented early in development, before large financial resources and efforts are committed to specific options. Once specific materials and options have been selected, strategies to prevent accident initiating events need to be evaluated and implemented. The next step is to implement safety options which suppress a hazard when an accident initiating event occurs. Releases can be prevented or reduced with fail-safe equipment and valves, adequate warning systems and controls to reduce and interrupt gas leakage. If an accident occurs and safety systems fail to contain a hazardous gas release, then engineering control systems will be relied on to reduce/minimize environmental releases. As a final defensive barrier, the prevention of human exposure is needed if a hazardous gas is released, in spite of previous strategies. Prevention of consequences forms the final defensive barrier. Medical facilities close by that can accommodate victims of the worst accident can reduce the consequences of personnel exposure to hazardous gases

New membrane materials for potassium-selective ion-sensitive field-effect transistors

NARCIS (Netherlands)

van der Wal, P.D.; van der Wal, Peter D.; Skowronska-Ptasinska, Maria; van den Berg, Albert; Bergveld, Piet; Sudholter, Ernst; Sudholter, Ernst J.R.; Reinhoudt, David

1990-01-01

Several polymeric materials were studied as membrane materials for potassium-selective ion-sensitive field-effect transistors (ISFETs) to overcome the problems related with the use of conventional plasticized poly(vinyl chloride) membranes casted on ISFET gate surfaces. Several acrylate materials,

Material Selection for Competition–A Case Study for Air Coolers

Directory of Open Access Journals (Sweden)

Luma A. H. Al Kindi

2018-02-01

Full Text Available Competition is one of the most important challenges that is facing the marketing of industrial products in today's markets. In this research study of the impact of material selection factor for air coolers of different materials is applied. Investigation on the air cooler windows which are part of the body of air coolers is conducted. Corrosion resistance, thermal conductivity, strength of material, weight, shape, cost and manufacturing process are the factors that are applied and calculated on three types of materials Aluminum, Galvanized steel and polypropylene. The physical properties of the three mentioned materials are used to calculate Merit Index .The corrosion average, according to Tafel Method depending the corrosion current and adopting contactors for the anodic and cathodic metals behaviors is performed. ANSYS is adopted using the three samples for the selected materials Aluminum, Galvanized steel and polypropylene to measure maximum stress and deflection are measured. Accordingly, the results are compared to choose the best alternative. It is observed that the polypropylene is the best choice depending three factors while the aluminum material is better depending two factors and the galvanized steel is regarded as the best in only one factor, the rest factors are identical when choosing  an alternative material for manufacturing the air cooler windows.

Pure zinc sulfide quantum dot as highly selective luminescent probe for determination of hazardous cyanide ion

Energy Technology Data Exchange (ETDEWEB)

Shamsipur, Mojtaba, E-mail: mshamsipur@yahoo.com [Department of Chemistry, Razi University, Kermanshah (Iran, Islamic Republic of); Rajabi, Hamid Reza, E-mail: h.rajabi@mail.yu.ac.ir [Chemistry Department, Yasouj University, Yasouj 75918-74831 (Iran, Islamic Republic of)

2014-03-01

A rapid and simple fluorescence method is presented for selective and sensitive determination of hazardous cyanide ion in aqueous solution based on functionalized zinc sulfide (ZnS) quantum dot (QD) as luminescent prob. The ultra-small ZnS QDs were synthesized using a chemical co-precipitation method in the presence of 2-mercaptoethanol (ME) as an efficient capping agent. The prepared pure ZnS QDs was applied as an optical sensor for determination of cyanide ions in aqueous solutions. ZnS nanoparticles have exhibited a strong fluorescent emission at about 424 nm. The fluorescence intensity of QDs is linearly proportional to the cyanide ion concentration in the range 2.44 × 10{sup −6} to 2.59 × 10{sup −5} M with a detection limit of 1.70 × 10{sup −7} M at pH 11. The designed fluorescent sensor possesses remarkable selectivity for cyanide ion over other anions such as Cl{sup −}, Br{sup −}, F{sup −}, I{sup −}, IO{sub 3}{sup −}, ClO{sub 4}{sup −}, BrO{sub 3}{sup −}, CO{sub 3}{sup 2−}, NO{sub 2}{sup −}, NO{sub 3}{sup −}, SO{sub 4}{sup 2−}, S{sub 2}O{sub 4}{sup 2−}, C{sub 2}O{sub 4}{sup 2−}, SCN{sup −}, N{sub 3}{sup −}, citrate and tartarate with negligible influences on the cyanide detection by fluorescence spectroscopy. - Highlights: • Preparation of functionalized ZnS quantum dots in aqueous media • Highly selective quantum dot based luminescent probe for determination of cyanide • Fast and sensitive determination of hazardous CN{sup −} by fluorescence quenching.