WorldWideScience

Sample records for seigyo zairyo gijutsu

  1. Corrosion control of electronic materials; Denshi zairyo no fushoku seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Y. [Hitachi Ltd., Tokyo (Japan). Mechanical Engineering Research Lab.

    1995-11-20

    Electronic materials are used in wide varieties of materials starting from hightech products like large computers, information network facilities and so forth, to vehicles, home electrical appliances, OA facilities, video game. Again, even though the part itself may be comparatively simple, high reliability is required when used in high degree system. Further, their uses irrespective to indoor or outdoor environments, are spread to wide range starting from the severe corrosive environments like coastal industrial area, drainage treatment place and so forth to low corrosive environments like general housing, offices and so forth. However, the classification of materials according to the environments where they are used is not so much carried out because preference is given to the function as an electronic part different to the large mechanical construction materials. In this report, regarding the corrosion control technology of electronic materials specially approach is made from material side, and among the various types of electronic materials, aluminium cable for LSI and magnetic materials are outlined. 37 refs., 10 figs., 2 tabs.

  2. Study on the advanced orientation control technology of biopolymers; Seitai kobunshi zairyo no kodo haiko hairetsu seigyo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Creation of new functional organic materials for the medical application has been investigated under the microgravity. Facilities of the Japan Microgravity Center were used for this study. For the high-speed synthesis of uniform polymer particles under the microgravity condition for ten seconds, appropriately good results were obtained in the oxidation polymerization of pyrroles. For the synthesis of organic conductive thin films by the electrolytic polymerization, the resistance of electrolyte became larger in the microgravity field. It was required to set conditions so as to enhance the effects of microgravity environment. For the orientation control and thin film formation of proteins, the bacteriorhodopsin was examined. It was found that the microgravity improved the quality of electrocoatings. When the surface tension and viscosity of coating liquid were appropriately controlled under the microgravity, thin films were able to be prepared by utilizing a change from 1g to {mu}g. When the high viscosity fluid is placed in the artificial two-dimensional space composing of two parallel plates, and the low viscosity fluid, such as air, is injected into the above, the interface grows in the finger shaped pattern, namely, viscous fingering. The influence of gravity on this phenomenon was also investigated. 11 refs., 45 figs., 5 tabs.

  3. Report on results concerning development of supermetal technology (FY2000). Innovative manufacturing technology for iron-based mesoscopic structured material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Tetsu kei mesoscopic soshiki seigyo zairyo sosei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing innovative manufacturing technology for microstructure steel having a crystal grain size of about 1 {mu}m or less and a dimensional thickness of 1 mm or more by homogeneous multi-phase structure steel making, R and D was conducted, with fiscal 2000 results compiled. This year, R and D, using a multi-functional integrated test rolling mill, resulted in obtaining ultra-fine grained steel, a steel plate of 5 mm in thickness and 100 mm in width with grains of 1 {mu}m or less homogeneously in the thickness direction. In the investigation on the characterization by the steel plate sample thus obtained and on the method for preventing degradation in elongation, it was proved that an ultra-refined microstructure containing martensite or austenite as the secondary phase has a suppressing effect on the degradation in elongation. Further, examination was made on the widening of a process window for the practicability in the future and on the optimization of large strain deformation conditions. In the method of analyzing and evaluating ultra-refined microstructures, an analysis technology such as an in-lens SEM was proved to be extremely effective on the analysis of microstructures of supermetals created by large strain deformation as well as on the observation of microstructures of a submicron level. (NEDO)

  4. Fiscal 1998 research report. R and D on super metal (Al system mesoscopic texture-controlled material); 1998 nendo seika hokokusho. Super metal no gijutsu kaihatsu (aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of Al materials with superior industrial characteristics (strength, corrosion resistance), this research has promoted development of large-size Al system materials with mesoscopic crystalline texture by high- strain accumulation control technology, and recovery and recrystallization control technology. In this fiscal year, (1) basic study on high-strain accumulation control technology, (2) study on a formation mechanism of ultra- fine crystal grains, and (3) development of a machining process were made. In (1), basic study on low-temperature rolling and study on rolling by rollers having different peripheral speeds were made. In (2), study on refining of recrystallized grains of 5000-base and 7000-base alloys was made. In (3), a low-temperature rolling equipment, and a ultra-rapid heating device were introduced. For the whole R and D project on super metal, the main research facilities such as a low-temperature rolling body for high- strain accumulation and a high-strain accumulative structure formation equipment (melt rolling equipment) for uniform nucleus formation in recrystallization were introduced to gain a firm foothold for the future application research. (NEDO)

  5. Report on development of super metal technology and on result of innovative technologies for producing material for controlling iron-based mesoscopic structure; 1999 nendo super metal no gijutsu kaihatsu tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    R and D was conducted for the purpose of 'establishing innovative technologies for producing microstructure steel having a grain size of approximately 1 {mu}m or less and a thickness of 1 mm through the formation of uniform multi-phase structure steel', with the results for fiscal 1999 summarized. In the subject year, a multi-functional integrated test rolling mill was introduced, with possibility validated for grain ultra-refinement by three types of large strain deformation, and with the effect of deforming conditions confirmed. As for the theoretical understanding of the mechanism of grain ultra-refinement and the establishment of its guiding principle, a progress was made in clarifying the ultra-refinement mechanism particularly by the strain-induced ultra-low-temperature diffusional transformation, revealing for example that micro-bands formed in deformed austenitic substructures provided the nucleation sites for ultra-fine ferrite. In the evaluation of properties on medium size samples prepared by the multi-functional integrated test rolling mill, remarkable improvement was confirmed in yield strength and tensile strength in martensitic steel or tempered martensitic steel as well as in ferritic steel. (NEDO)

  6. Report on results concerning development of supermetal technology (FY2000). Development of technology for aluminum-based mesoscopic-structured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength alloys through grain refinement, R and D was conducted, with fiscal 2000 results compiled. This year, using hot rolled plates and cold rolled plates of 5083 based alloys, research was carried out on an optimum warm processing method for forming microstructures. When 5083 alloys were rolled with a large reduction by one pass under a warm to hot temperature range, recrystallized grain structures were obtained having 3-4 {mu}m in the surface and 7-8 {mu}m in the center. The proof stress of these specimens was about 1.3 times as strong as an ordinary 5083 alloy soft material while the elongation was about the same. In the case of 7475 based alloys with Zr added in place of Cr, a warm rolling method, in which the alloys were heated to 350 degrees C and repeatedly reheated by one pass at that temperature, was found effective in forming micro-subgrain structures. By the warm rolling method in which roll temperature was suitably heated, it was made possible to steadily form thermally stable microstructures in 7475 based alloys. The 7475 based alloy plate having a microstructure is superior to an ordinary 7574 plate in resistance against stress corrosion cracking. (NEDO)

  7. Achievement report for fiscal 1998 on the technological development of super metals. Technology to create iron-based mesoscopic tissue controlling materials; 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Tetsukei meso scopic soshiki seigyo zairyo sosei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research and development has been carried out on super metals with an objective to draw out properties possessed by iron and steel materials to their maximum extent and further enhance their recycling performance to make them friendly with global environment. The final goal of this project is to 'establish a technology to create micro tissue steel having crystalline particle diameter of about 1 {mu}mm or less and size having thickness of 1 mm or more by making the steel tissues uniform and multiple in phase'. The studies in the current fiscal year were moved forward mainly on obtaining ultra fine crystalline particles of 1 {mu}mm or less, identifying the ideal large distortion processing conditions, and structuring the guidance principles for ultra-fine micronization of the crystalline particles by using large distortion processing. Discussions were also launched on further micronization of crystalline particles by optimizing chemical composition and on expansion of the process windows assuming practical application thereof in industrial scale. Furthermore, material property evaluation was also begun on ultra-fine crystalline particle materials of smaller than 1{mu}mm. As the mesoscopic structure analyzing technology for the ultra-fine crystalline particle materials, an in-lens resolution SEM was introduced, and the basic method was established. (NEDO)

  8. Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

  9. FY 1999 research and development of technologies for creating original high-function materials. Development of technologies for functionalized materials for power generating facilities (Report on the R and D results of controlling precise structures of polycondesed systems); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu (shukugokei seimitsu kozo seigyo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for the polymerization catalysts and precise polymerization processes which can freely control the primary structures, e.g., molecular weight, regularity, branching and terminal group structures, of the polymers produced by polycondensation and ring-opening polymerization, in order to drastically improve their functions, and the FY 1999 results are reported. The basic studies on the precise polycondensation successfully lead to chemoselective synthesis of polymers by the direct polymerization, and synthesis of polyamides of narrow molecular weight distribution and high-molecular-weight aliphatic polyesters. The other items studied include precisely, regularly sequential polymerization by amine activation, innovative synthesis of polycarbonate, precise control of branching structures, regioselective oxidative coupling polymerization, and matrix polycondensation. The basic studies on the controlled ring-opening polymerization cover cationic ring-opening polymerization behavior of 6-membered thiocarbonate derivative having an ester group, to generalize the polymerization controlled by neighboring group participation. The other items studied include precise control of branching structures, molecular weights, network polymer structures, and polymer unit sequences. (NEDO)

  10. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  11. Fiscal 1999 achievement report. Development of technologies for creating high-quality crystalline materials for low-loss power control devices; 1999 nendo teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Researches are conducted for the advancement of, and loss reduction for, semiconductor devices for controlling electric power. Physical properties of molten semiconductors etc. are accurately measured in a microgravity environment and computer simulations are performed, which are for the production of larger-diameter, higher-quality semiconductor crystal materials. In the measurement of physical properties of molten semiconductors etc. carried out at JAMIC (Japan Microgravity Center) free-fall facilities where a high-quality microgravity environment is available, measurements are made of the surface tension, density, viscosity index, heat conductivity, and vertical spectral factor of the molten silicon. Solubility is measured of silica, silicon nitride, and silicon carbide, and, in equilibrium with these, the oxygen, nitrogen, and carbon in molten silicon, and highly reliable data are obtained. As for the comprehensive analysis code developed under this subject, the X-ray image data of the surface of a solid solution, collected from a crystal growing in a small Cz furnace at the NEC Fundamental Research Laboratories, and data of oxygen concentration in the silicon crystal agree excellently with the result of calculation, which suggests that the code is reliable. (NEDO)

  12. Report on results 1998. Technological development to create high quality crystal material for low loss power controlling element; 1998 nendo seika hokokusho. Teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper refers to the development of basic technology for manufacturing crystal materials of a large diameter and uniform properties for the purpose of sophistication and low loss of semiconductor controlling elements for electric power. An experiment was conducted using the drop tower of the underground agravity center. Results in fiscal 1998 were explained. With counter-measures taken in for improving measuring accuracy of an electromagnetic floating furnace, the accumulation and evaluation were performed of the highly reliable data of the surface tension and density of Si. The measurement of the viscosity coefficient of Si under micro-gravity was successful for the first time in the world, as was the measurement of the contact angle between solid/liquid, other than the measurement of specific heat, thermal conductivity and spectral emissivity of Si. The viscosity coefficient, unlike the conventional report, showed Arrhenius' linearity. In the comupter simulation, boundary data were exchanged between element analysis programs, developing a basic general analysis program as scheduled. The result of a micro simulation by molecular dynamics method was in agreement with the observation result by a transmission type electron microscope, bringing the first success in the world. In the Cz furnace model experiment, effect of rotation for example was elucidated on turbulence in the melt by using lasers. (NEDO)

  13. FY 1995 annual report on development of techniques for creating high-quality crystalline materials for low-loss power controlling components; 1995 nendo teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    The R and D project is implemented for manufacturing high-quality semiconductor crystalline materials of large size and uniform characteristics, in order to improve semiconductors as components for controlling power systems, and reduce power loss. The semiconductor melts, in particular silicon melt, is highly reactive, readily reacting with the atmosphere and crucible holding the melt, and it is difficult to collect their thermal properties. Therefore, an electro-magnetic levitation furnace working under a microgravity is used, to dispense with a crucible for measurement of their properties in the absence of thermal convection. The preliminary tests using the furnace produce surface tensions of the melts, because Ge is less reactive than silicon, stable in the form of a GeSbTe compound, and not wettable with Al{sub 2}O{sub 3}, MgO, SiO{sub 2} or Si{sub 3}N{sub 4}. The measurement of electric resistance of InSb indicates that InSb has characteristics of a semiconductor when it is solid and a metal when it is liquid, as is the case with Si. The program codes are developed by each researcher, and combined with each other to establish the comprehensive thermal flow analysis program, which includes all of the aspects of the internal CZ furnace structure for growing the crystals. (NEDO)

  14. Report on the investigational study on the technical trend of temperature control materials for high efficiency LED lighting use; Kokoritsu LED shomeiyo no ondo seigyo zairyo no gijutsu doko ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of the innovative conservation of lighting use energy, a project is being promoted with the aim of developing light emitted diode (LED) and commercializing lighting use light source substituting for fluorescent light. In this study, the following were conducted: literature survey on Peltier materials as temperature control materials for high efficiency LED lighting and the making of them as elements, extraction of technical subjects in the commercialization of LED cooling use Peltier element materials, market surveys/analyses were made of the fields of application including the LED cooling use field. As a result, for the commercialization of temperature control use Peltier elements of lighting use LED, the desirable performance index is 5x10{sup -5}/K or more. Bi{sub 2}Te{sub 3} elements which are now commercially available as Peltier elements are not good in performance and have the toxicity problem. As a candidate of temperature control use materials of lighting use LED, Mg{sub 2} (Sn, Si) or clathrate system are regarded, but the point, etc. were pointed out that it is necessary to improve thermoelectric characteristics. (NEDO)

  15. Fiscal 1999 R and D project for industrial science and technology. R and D of technology for creating innovative and high-functional material - development of technology for structural control material (Report on result of R and D of harmonized molecular material); 1999 nendo dokusoteki kokino zairyo sosei gijutsu no keknkyu kaihatsu seika hokokusho. Kozo seigyo zairyo gijutsu kaihatsu (bunshi kyocho zairyo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of contributing to the development of optical elements, devices, sensors, high performance catalysts, etc., R and D was conducted on fundamental technologies for creating materials using harmonized molecular actions, and the fiscal 1999 results were reported. In the R and D of self-assembled molecular film materials, an electric-field sensitive self-assembled molecular film was experimentally manufactured, as were self-assembling electroluminescent and lyotropic liquid crystal pigmentary film materials. In the R and D of mesophase materials, for rod-like liquid crystal systems, a material was successfully developed possessing a transparency of 90% in the visible region accompanied with an optical phase difference of 4.0 microns. For disk-like liquid crystal systems, a diminishing tendency of obtainable photoelectric current was confirmed even with a small change in the orientation after photopolymerization. In the R and D of microporous materials, synthesis was performed for system-controlled metallosilicates and shape-controlled microporous materials. Further, structural correlation was examined for organic templates and microporous materials. (NEDO)

  16. 1998 report on results of R and D project for industrial science and technology (R and D for technologies of producing innovative high performance material) (development of technologies for structural control material). R and D for high stimuli-responsive material; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report was made on the results of 1998 R and D concerning high stimuli-responsive materials. This R and D was intended to develop technologies for producing, by copying organism, innovative new stocks and new materials which repeatedly provide functions such as separating, transmitting and moving in response to stimuli. In the R and D of polymeric high stimuli-responsive materials, studies were conducted on multi-stimuli-responsive separation materials, molecular recognition controlled separation materials, and cell adhesion/separation materials with molecular recognition function. In the R and D of composite high stimuli-responsive materials, release controlled function materials and materials for actuator were studied. The investigation and research of common basic technologies were carried out on such subjects as synthesis and functional development of multi-signal responded polymer gels, development of temperature-responsive chromatography, synthesis and characterization of novel stimuli-sensitive materials, studies on structural characterization of intelligent gels, novel thermosensitive polymers, polyelectrolytic model networks, etc. (NEDO)

  17. FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

  18. Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

  19. FY 1998 research result report. Ultra-high liquid crystal technology development for energy use rationalization (Technology of design/control/analysis of new functional electronic materials of the ultra-high electronic technology development promotion project); 1998 nendo kenkyu seika hokokusho. Energy shiyo gorika chosentan ekisho gijutsu kaihatsu (chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Element technology is studied to realize a reflective-type, full-color, and high-resolution liquid crystal display for super-low power consumption data display. As to the functional compound microstructure formation technology, a 4-inch panel was trially fabricated using two-layer guest-host liquid crystal technology to achieve the desired display performance by control of molecular orientation. Further, holographic PDLC elements were favorably test-fabricated. A ferroelectric PZT thin layer was formed by forming layer at low temperature at which a glass substrate can be used. Optical interference/optical dispersion type optical control materials were studied by liquid crystal/polymer composition. Also studied were super-pure/super-reliable liquid crystal compound/liquid crystal composite systems and super-anisotropic liquid crystal compound by modeling ionic impurities and liquid crystal molecular interaction. In relation to the control technology of optical reflection characteristics, effects of liquid crystal molecular structures (derivative effect and copolymer composition) on orientation were elucidated. As to the technology to form multi-dimensional anisotropic structures, efforts were made for the heightening of formation technology of simple RGB (red, green, blue) directional reflection layers using acrylate materials. The paper also outlined the comprehensive survey. (NEDO)

  20. Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

  1. 1998 report on results of technological development of super metal. Innovative technological development for producing advanced structure controlled metallic material (high-speed large reduction rolling technology); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kodo soshiki kozo seigyo kinzoku zairyo sosei gijutsu kaihatsu (kosoku daiatsuka atsuen gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A report was made on the 1998 results concerning technological development of super metal. In the 'research and development of super metal', metallurgical examination has been made on crystal grain super refining process using a machining simulator, with studies carried out on crystal grain refining by utilizing large-strain deformation with more than 50% deformation for a single pass and a diploid structure. As a result, it was found that the crystal grain size can be refined to approximately 1{mu}m. Consequently, in fiscal 1998, a high-speed large reduction rolling test equipment was developed capable of rendering a sheathing technology in a mechanically testable size by a rolling method. This test equipment has such capacity as the maximum load of 1,000 ton and the maximum torque of 95 ton/m and is a rolling mill whose scale is largest in the nation on the laboratory level. The rolling speed can be 120mpm, a very fast speed for a large sized rolling mill. Moreover, equipped with an immediate water cooling facility adjacent to the rolls and an automatic operating system for example, it is a high function rolling mill capable of cooling and rolling that render the complex and delicate sheathing technology of super metal. (NEDO)

  2. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (development of precise structure control materials for enhancement of oil refining); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the R and D of technologies for creating original high-functional materials under the R and D system of industrial scientific technology. Japan chemical Innovation Institute (JCII) is conducting intensive joint researches under consignment from NEDO with private companies, universities and national research institutes. Among those, the paper reported the fiscal 1997 results of the following two researches conducted as development of precise structure control materials for enhancement of oil refining: precision catalytic polymerization and multi-dimensional space polymer. As to the precision catalytic polymerization, the paper is aimed at developing base technologies for the molecular weight and stereoregularity by which remarkable improvement in performance of addition polymerization type polymer can be expected, and on the development of a polymerization catalyst which arbitarily controls the primary structure such as end group structure and of a precision addition polymerization process. Subthemes are addition polymerization with limit and oriented catalytic polymerization. In relation to multi-dimensional space polymer, the paper is aimed at developing highly selective polymerization technology of aromatic compounds using enzyme related catalysts and synthesis technology of regular structure polymer, and synthesis technology of new polymer group having a new chain pattern except covalent bond/new polymer group having characteristics in three-dimensional space geometric structure. 244 refs,, 160 figs., 94 tabs.

  3. Fiscal 1998 R and D on original advanced material creation technology (development of precise structure control materials for oil refinery improvement). R and D result report on multi-dimensional polymers; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu) seika hokokusho. Tajigen kukan polymer no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of radical-controlled synthesis technology of aromatic compounds using enzyme-related catalysts and synthesis technology of ordered compounds, and development of synthesis technology of new polymer groups with non-covalent bond linkages and new topological structures, this R and D on multi-dimensional polymers is promoting 2 research themes, (1) precise polymer synthesis technology using enzyme-related catalysts, and (2) chemical synthesis technology for polymers with non-covalent bond linkages and new topological structures. The joint research on (1) precise polymer synthesis technology using enzyme-related catalysts established the high-yield synthesis technology of phenol dimer first in the world. The joint research first studied the synthesis using 2,6-dimethylphenol as monomer through synthesis of phenol groups using ferrosalen, and obtained the mixture of polymer components more than 10,000 in molecular weight and low-molecular weight components by using 1,4- dioxane as solvent. (NEDO)

  4. Research and development of a technology to create original high-function materials in fiscal 1998 (development of precision structure controlling materials by improving petroleum refining). Report on achievements in research and development of precision catalytic polymerization; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho. Sekiyu seisei kodoka seimitsu kozo seigyo zairyo kaihatsu (seimitsu shokubai jugo no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research and development on precision catalytic polymerization aims at developing polymerizing catalysts that can control arbitrarily the molecular weight and three-dimensional regularity by which rapid enhancement can be expected in performance of additional polymerization type polymers, and the primary structure of terminal groups. Works are being done on two sub-themes of ultimate additional polymerization and orientation catalyst polymerization. The research and development of the ultimate additional polymerization included structural control in polymerization reaction in vinyl chloride, vinylester and acrylic monomers, radical polymerization with precision orientation control, anionic polymerization with precision structural control, and precision polymerization utilizing asymmetric metal porphyrin complexes. In the research and development of the orientation catalyst polymerization, the orientation catalyst polymerization was researched and developed, elementary reaction of metallocene was elucidated, high-performance carrier catalysts were developed, advanced function polymers were synthesized at high precision based on metathesis, and improvement of functions of polyolefin was researched and developed. Surveys and studies were carried out on fundamental technologies common to the above two themes re-commissioned to five universities. (NEDO)

  5. Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

  6. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

  7. FY 1999 report on the results of the technology development of super metal. Development of technology of high corrosion resistant iron-base fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing iron/steel materials which enable remarkable improvement of maintenance loads and longevity of oil field developmental materials, study was conducted for remarkable improvement of strength and corrosion resistance by making crystal grain of iron/steel materials micro-fine to the limit, and the FY 1999 results were summed up. The study was conducted on the technology of fine structure formation using strong magnetic field and technology to predict material quality of micro structure using computational science. As a result, it was found that the fine grain even in size can be obtained by a combination of magnetic field orientation and recrystallization. By this, an image was constructed of the industrialization process of fine grained steel production which was combined with warm rolling process and applied strong magnetic field. Using the method to homogenize the finite element method, the basement was established for the method to evaluate an effect of the second phase on mechanical characteristics of fine multi-phase structure steel. The cementite single-phase film which is an important structural phase of carbon steel was successfully formed, and the Young's modulus and Poison ratio were determined as basic data for material design. (NEDO)

  8. Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

  9. FY 1999 report on the results of the technology development of super metal (R and D of the undersea oil production support system). Development of technology of aluminum-base high corrosion resistant fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu (aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihtsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing aluminum materials excellent in industrial characteristics, a study was conducted to create large-sized aluminum materials having mesoscopic crystal structure, and the FY 1999 results were summarized. In this fiscal year, to create the fine crystal grain structure, the following were conducted: fundamental study of high strain accumulation process, study of a mechanism of fine crystal grain formation, development of the processing method, and development of evaluation technology. In the study of high strain accumulation process, effects were examined of conditions of molten metal rolling on castability. Fundamental studies were also made of innovative technologies such as ECAP method, pre-forged structure controlling rolling, accumulative roll bonding and thermomechanical treatment. In the study of the mechanism of fine crystal grain structure formation, the following were conducted: Al-Mn base alloys produced by molten metal rolling, 6061 alloys by warm rolling with different peripheral speed rolling, and 7000 group alloys by warm rolling. As to the processing method, study was made on low-temperature rolling technology and rapid heat treatment technology. As to the evaluation technology, study was made on evaluation of crystal grain diameter by EBSP. (NEDO)

  10. Report on results concerning development of supermetal technology (FY2000). Development of technology for high-anticorrosive iron-based microstructured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of greatly improving strength and corrosion-resistance through ultra-refinement of crystal grains of steel materials, research was conducted on microstructure refinement technology utilizing strong magnetic fields and on mechanical property estimation technology for ultra-refined structure steel using computational science, with fiscal 2000 results compiled. In the research for grain refinement utilizing magnetic fields, an inline experiment of transformation was carried out and, as a result, equi-axed grains of 1.6 {mu}m were attained on a 3 mm thick steel plate of commercially used composition by a method of recrystallization after cold rolling. The experiment revealed that the 1 {mu}m grains could be obtained by setting cold-rolling work load to 80%. In addition, data were acquired relating to conditions such as steel composition affecting the formation of orientation in structures, work load and rolling temperature for areas to be recrystallized, holding temperature and time in the magnetic field, and intensity of the magnetic field. In the research for estimating mechanical properties of microstructures by computational science, a Monte Carlo simulation was carried out by employing the result of a polycrystal plasticity method program as the initial value, with a prototype established of the integrated simulation method from the deformation to the microstructure formation. (NEDO)

  11. Achievement report for fiscal 1998 on the development of super-metal technology. Development of technology of high corrosion-resistance iron base controlled microstructure materials; 1998 nendo super metal no gijutsu kaihatsu. Kotaishokusei tetsukei bisai kozo seigyo kinzoku zairyo gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    During ultrafine structure formation due to transformation from austenite to ferrite in an intense magnetic field, the transformation is accelerated by the thermodynamic stabilization of the ferrite phase which is ferromagnetic. The application of an intense magnetic field works effectively during the generation of nuclei. When a magnetic field is applied during reverse transformation, a honeycomb 2-phase structure is formed oriented toward the direction of the magnetic field and, when the structure is vertically compressed, the recrystallized structure is made ultrafine effectively. In pearlite transformation, hardening occurs when carbon atoms supersaturated in density are introduced in the presence of a magnetic field gradient, and curing further promotes precipitation hardening. In a ferrite complex phase system, wherein ultrafine globular cementite is uniformly distributed, plastic instability becomes explicit in a tensile test. There is a good possibility that an ultrafine structure recrystallization model may be built by calculation, into which the distribution of energy stored prior to recrystallizing nucleus formation is incorporated. The profile of a conceptual process of off-line or in-line integration of heavy-strain process and intense magnetic field application has become tangible. (NEDO)

  12. FY 1998 annual report on the results of new industry creation type industrial science and technology research and development on the research and development of supermetals. Development of techniques for controlling structures of nano-amorphous materials; 1998 nendo super metal no gijutsu kaihatsu. Nano amorphous kozo seigyo zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the FY 1998 results of the development of techniques for controlling structures of nano-amorphous materials. For the development of techniques for finely dispersing fine particles, mechanical alloying (MA) and mechanical milling (MM) are investigated, to structure nano-crystals in common steel, for which hot isostatic pressing is evaluated as a consolidation process for the MA- and MM-prepared powders in the FY 1998. For researches on high-speed particle deposition and super plastic forming, an Al-Ni, Al-Fe and Al-Ti alloy are selected as the nano-structure materials to be prepared by evaporation, and various compositions of these systems are evaporated, in order to investigate their microstructures, mechanical properties and thermal stabilities. For researches on techniques for controlling phases with the aid of high-density energy, the R and D efforts are directed to exploration of composition of high resistance to corrosion by acid at dew point, preparation of non-equilibrium (e.g., amorphous) powders, and development of solidification and forming techniques, with the target of creation of an amorphous alloy showing corrosion resistance at least twice as high as that of the commercial corrosion-resistance material and formable into a bulk shape having a thickness of at least 1 mm. For researches on controlled cooling techniques, the basic data are collected. (NEDO)

  13. Achievement report for fiscal 1998 on research and development of technologies for creating high-performance materials under the industrial and scientific technology research and development project. Control of condensation-based precision structures (High-performance materials for power plant facilities); 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) shukugokei seimitsu kozo seigyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The goal is to prepare a base for the development of polymerizing catalysts and precision polymerization processes which will enable the arbitrary control of molecular weight, regularity, branching, and primary structures such as terminal groups, which effort will lead to a remarkable advancement in condensation polymerization and open-ring polymeric material performance. Endeavors are on to fulfill two separate purposes, that is, precision condensation polymerization and controlled open-ring polymerization. In the study of precision condensation polymerization, at issue are basic studies and the development of precision control technologies for arrangement, molecular weight, branching, and matrix condensation polymerization. Also at issue are the development of technologies of position selective oxidization polymerization and precision conjugate high-molecular condensation synthesis. Concerning open-ring control polymerization, precision control technologies will be developed involving branching, molecular weight, crosslinking, arrangement, and the structure of cyclocarbonate open-ring polymerization. Open-ring control polymerization technologies are also under study by use of organic metal complexes. A survey of technological trends is also explained. (NEDO)

  14. Automotive technology. ; Chassis. Jidosha gijutsu. ; Chassister dot sharyo seigyo sochi

    Energy Technology Data Exchange (ETDEWEB)

    Ota, K.; Mor, H.; Ishizeki, S. (Fuji Heavy Industries Ltd., Tokyo (Japan))

    1990-07-01

    According to the trend of car suspensions announced in 1989, not only sports cars but also sedans have extensively applied a multi-link type and a double-wishbone type which are to improve operation stability and comfortableness by reexamining all their fundamental structures. Active suspensions with electronic control have been put to practical use and adopted for the first time to mass-produced cars such as INFINITI'' and CELICA''. Concerning steerings, most types of light cars are now equipped with power steerings. Moreover, application of air bags has increased, and safety has been improved by commercialization of the first mechanical air bags in addition to the conventional electrical ones. As for brakes, more anti-lock brakes have been used for 4WD cars and low-displacement cars. Motorcars with a traction control system have consequently increased. Thus both the anti-lock brakes and the traction control system are contributing to the improvement in safety. 17 figs., 2 tabs.

  15. Fiscal 1997 report on the development of an energy use rationalization ultra-high tech liquid crystal technology. Project of development/promotion of ultra-high tech electronic technology / technology of design/control/analysis of new functional electronic materials; 1997 nendo kenkyu seika hokokusho energy shiyo gorika chosentan ekisho gijutsu kaihatsu. Chosentan denshi gijutsu kaihatsu sokushin jigyo / shinkino denshi zairyo sekkei seigyo bunseki gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    A research was conducted with the aim of developing an ultra-low power consuming type information display which supports the next next generation informatizing society. As to the function combined type fine structure formation technology, a formation technology of fine structure supporting multi-layer pixel by organic polymer materials was established to confirm a possibility of adopting it to high functional liquid crystal display. Concerning the high functional fine structure formation technology, a study was proceeded with on holographic PDLC which is an interference reflection coloring method. In relation to the low temperature film formation technology of ferroelectric thin films, a film formation device was introduced to obtain basic data, and at the same time a possibility was studied of improving film characteristics by laser annealing conducted after the film formation. Moreover, concerning the new functional material technology, studies were made of optical interference/high light-scattering control materials, light alignment elements, ultra-high purity/ultra-reliable optical materials, ultra-anisotropy optical materials, etc. About the light reflection characteristics control technology, studied were new liquid crystal molucular orientaion control technology, multi-dimensional anisotropy structure formation technology, etc. 100 refs., 273 figs., 58 tabs.

  16. Fiscal 2000 achievement report on the important regional technology research and development. Research and development of super-functional environment resistant materials by controlling trace metal ion implantation; 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Gokubiryo kinzoku ion chunyu seigyo ni yoru chokino taikankyo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop highly reliable materials greatly improved in high temperature oxidation resistance, high temperature wear resistance, and high temperature corrosion resistance, by implanting traces of a high melting point metal into the substrate surface or into the compound coating the substrate surface or deeper into the substrate. Activities are conducted in the five fields of (1) the research and development of element technologies for ion processes, (2) research and development of high temperature oxidation resistant materials, (3) research and development of high temperature wear resistant materials, (4) research and development of high temperature corrosion resistant materials, and (5) the technology of ion implantation into complicated shapes. In field (2), in concrete terms, development is in progress of automobile supercharger rotor materials and gas turbine blades. In field (5), studies are conducted about the cathodic arc aided surface reforming for 3-dimensional shapes and ion implantation characteristics and about shunting arc aided plasma formation for solid/metal materials. (NEDO)

  17. Report on the results of efforts for fiscal 1997. Development of technologies for creating high-quality crystal materials for low-loss power control devices; 1997 nendo seika hokokusho. Teisonshitsu denryoku seigyo soshiyo kohinshitsu kessho zairyo sosei gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Basic technologies are developed for the manufacture of high-quality crystal materials large in diameter and homogeneous in property which will allow power control semiconductor devices to grow more sophisticated in function and to be lower in the loss they suffer. Physical properties of molten semiconductor and the like are measured accurately, which include surface tension, density, viscosity, electric conductivity, thermal conductivity, emissivity, diffusion coefficient, vapor pressure, heat capacity, contact angle, and solid solution equilibrium distribution coefficient. In computer-aided simulation, as in the previous year, simulation codes are developed for the analysis of flow, temperature distribution, and diffusion behavior in the gas phase; simulation codes are developed for the analysis of 3D unsteady thermal flows in the melt; and a main program is developed which governs experimental calculations. As for experiments in model Czochralski crucibles, small crucible are used in which experiments are conducted in the temperature range of normal to 200degC for the acquisition of experimental data for verification. Measured by use of the model crucibles are the temperature distribution in the bath, the surface flow speeds, and the flows inside the melt. 140 refs., 153 figs., 10 tabs.

  18. Fiscal 2000 report on result of R and D of industrial science and technology that creates new industry. Development of supermetal technology (development of nano-amorphous structured material); 2000 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted for the purpose of manufacturing innovative iron-based alloy materials that excel in high temperature strength, toughness and superplastic forming, with fiscal 2000 results compiled. In the technological study on high-speed grain accumulation and superplastic forming, the researchers were engrossed in developing an aluminum bulk material of nano-crystals. This year, an Al-Fe two-element based alloy using Fe element was evaluated in the composition, thermal processing conditions and physical properties, with a bulk material obtained having a grain size of several tens in nm at 2at% Fe level, a strength of 750-850 MPa and a tenacity (Kc value) of 45-65 MPa(center dot)m{sup 1/2}. In the research of technologies for utilizing and controlling high density energy, design of materials was progressed for strong-acid resistant dew point corrosion materials, leading to the discovery of an alloy composition Ni-10Cr-5Nb-16P-4B whose subcooled liquid zone was wider than the Ta-added alloy of the previous year. Use of He gas as injection gas enabled a quality amorphous powder to be obtained in kg units. In the development of bulk amorphous producing technologies, this powder was thermostatically rolled to make a dense bulk amorphous plate of 2.8 mm thick and about 100 mm long. (NEDO)

  19. Investigational report on the trend of control technology; Seigyo gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    For the purpose of corresponding to changes of the industrial structure and making full use of the control technology, the paper investigated the state of the application. High-grade automation in the manufacturing industry has reached the spread of use at big companies for these 10 years. The hierarchical structure of business/process/DCS has been completed, and the optimal control and the advanced control have been realized. The development and spread to the much wider field is anticipated. The soft structure system is needed for equipment improvement in view of the life cycle of equipment and toward the elimination of bottlenecking. For the design of the control system, commercial tools began to be much used, and it is expected in future to accumulate and recycle the knowledge/knowhow for effective design work. Further, strict simulation models based material balance and heat balance have also been on the rise, and the advance in technology is expected. Because of the total productivity of the production equipment, the control technology is anticipated not only for the pursuit of controllability but for the use as supporting technology in the operation/driving/failure diagnosis for working out, carrying out and evaluating the optimum operation plan. 18 refs., 99 figs., 100 tabs.

  20. Leading research on artificial techniques controlling cellular function; Saibo zoshoku seigyo gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Advanced research and its applicability were surveyed to apply the advanced functional cells to industry. The basic target was set to develop, produce, control and utilize the functional cells, such as intelligent materials and self-regulation bioreactors. The regulation factors regarding apotosis, which is a process of cell suicide programmed within the cell itself of multicellular organisms, cell cycle and aging/ageless were investigated. Furthermore, the function of regulatory factors was investigated at the protein level. Injection of factors regulating cellular function and tissue engineering required for the regulation of cell proliferation were investigated. Tissue engineering is considered to be the intracellular regulation by gene transduction and the extracellular regulation by culture methods, such as coculture. Analysis methods for cell proliferation and function of living cells were investigated using the probes recognizing molecular structure. Novel biomaterials, artificial organ systems, cellular therapy and useful materials were investigated for utilizing the regulation techniques of cell proliferation. 425 refs., 85 figs., 9 tabs.

  1. Leading research on cell proliferation regulation technology; Saibo zoshoku seigyo gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing intelligent material, animal test alternative model, bio-cell analysis equipment, self-controlling bio-reactor and medical material, development of functional cells was studied by cell proliferation regulation technology. In fiscal 1996, the expression analysis and separation technology of specific gene for cell proliferation, and the intracellular regulation technology were surveyed from the viewpoint of intracellular regulation. The cell proliferation regulation technology by specific regulating material of cells, extracellular matrix, coculture system and embryonic cell was surveyed from the viewpoint of extracellular regulation. In addition, based on these survey results, new cell culture/analysis technology, new bio-material, artificial organ system, energy saving bio-reactor, environment purification microorganism, and animal test alternative model were surveyed as applications to industrial basic technologies from a long-term viewpoint. The approach to cell proliferation regulation requires preparation of a concrete proliferation regulation technology system of cells, and concrete application targets. 268 refs., 43 figs., 4 tabs.

  2. Survey of advanced composite material technology; Senshin fukugo zairyo gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Results of functions and examples are investigated and described for more than 190 fiber reinforced composite materials. There should be a new viewpoint for even the same material when changing the point to observe it, and new industries will be expected if the viewpoint is adequate. This report has proposed a new concept of `composite functions.` The development works based on non-strength functions which will differentiate the other materials have been stressed. After describing the brief history of the advanced composite materials and significance of composite functions, the present situations and future possibilities of such functions as heat resistance, electricity-electromagnetism, chemicals-proof, adsorption, vibration-proof and resistance, tribology, erosion, sound, adaptability to living bodies and etc. have been examined based on the practical examples. As the future important subjects, adapting possibility of materials having composite functions to marine structures, and possibility of water cleaning system are described. 59 refs., 4 figs., 10 tabs.

  3. Achievement report for fiscal 1998 on research and development of multifunction members structure control technologies. Development of advanced surface treatment technologies for methane-fueled aero engines (1. Microstructure control technologies for ultrahigh temperature members); 1998 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu. Methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu (chokoon buzai mikuro kozo seigyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The carbon fiber reinforced carbon composite materials (C/C composites) strong at ultrahigh temperatures are taken up. So as to improve on its resistance to oxidation, corrosion, and abrasion as well as on its strength at ultrahigh temperatures, an ion engineering-assisted technique is used to reform the C/C composite surface layer and a technology is developed for thin coating formation on the C/C composite surface. Next, technologies are developed for multifunction coating formation on top of the surface, for defect prevention or removal from the C/C composite, and for adhesion enhancement between the C/C composite fibers and the matrix. Technologies are further developed for evaluating hostile environment withstanding capabilities at ultrahigh temperatures. In this fiscal year, in the study of microstructure controlling multilayer coating technologies, development is conducted of technologies of ion engineering-assisted surface control and reform and of technologies of forming multifunctional coatings high in reliability and resistance to corrosion. In the field of microstructure control composition, 3-dimensional carbon fiber reinforced carbon composite materials are manufactured by way of trial and evaluated, and their behavior under rigorous conditions is evaluated. (NEDO)

  4. FY1995 research on nonlinear optical devices using super-lattice semiconductors; 1995 nendo chokoshi active hisenkei soshi wo mochiita chokosoku hikari seigyo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose is to develop technologies on efficient generation and control of femtosecond optical pulses using a novel semiconductor optical devices. We studied a modelocked Cr:forsterite laser pumped by a diode pumped Nd:YVO4 laser. Both Kerr lens mode locking and semi-conductor saturable absorber initiated mode locking have been achieved. The minimum pulse width for pure Kerr lens mode locking is 26.4 fs, while for the semiconductor saturable absorber initiated mode locking, the pulse width is 36 fs. The latter is very resistant to the environment perturbations. We also present the measured dispersion data for the forsterite crystal and the SESAM, and discuss the dispersion compensation technique. (NEDO)

  5. Presentation of electric motor and motor control technology for electric vehicles and hybrid vehicles; Denki jidosha hybrid sha yo motor oyobi motor seigyo gijutsu no shokai

    Energy Technology Data Exchange (ETDEWEB)

    Matsudaira, N.; Masakik, R.; Tajima, F. [Hitachi, Ltd., Tokyo (Japan)

    1999-02-01

    The authors have developed a motor drive system for electric vehicles and hybrid vehicles. This system consists of a permanent magnet type synchronous motor, an inverter using insulated gate bipolar transistors (IGBTs) and a controller based on a single-chip microcomputer. To achieve a compact and light weight synchronous motor, an internal permanent magnet type rotor structure was designed. This paper presents motor control technology for electric vehicles, such as an optimization method of field weakening control and a new current control method. (author)

  6. Fiscal 1998 research report on micro-particle control process technology; 1998 nendo micro ryushi seigyo process gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For establishment of process technology realizing control of forms and structures of micro-particles on practical equipment, research was made on related elementary technologies and current technologies. The research was promoted aiming at synthesis of micro-particles from nanometer to micrometer in size and their application to functional materials, establishment of the methodology for correlating the microstructure and function of micro-particle materials with fabrication process, and establishment of a common-base technology system in chemical technology aiming at fabrication of functional materials. As for the common- base technology, to clarify its importance, research was made on the fabrication method and dispersion mechanism of nano- particles, particle arraying method by coating, device fabrication technique by coating, and one-step synthesis and coating of nano-particles. As for the project research, synthesis of monodispersed nano-particles at large production rates, fabrication of thin films and bulk materials by arraying and coating. (NEDO)

  7. Leading research report for fiscal 1999. Survey and research on microparticle control process technology; 1999 nendo micro ryushi seigyo process gijutsu no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the functional upgrading of electronic equipment which will support the computerized society in the 21st century, a substance itself is required to exhibit novel functions or to behave better on a reduced amount. Dependence on the synthesis of new materials alone has its own limit, but a method of reducing the substances conventionally known for their safety into particles of the nanometer scale will be one of the solutions. Micro-science and micro-technology are in progress in Japan and abroad, which mainly deal with particles 10nm-100nm in size. To make better use of the functions of substances, there should be single nanoparticles 1nm-10nm in size. Such particles are easy to coagulate, however, and it is difficult to keep them in their nanometer-scale single state free of coagulation. If Japan succeeds in the development of 1nm-10nm size nanoparticle structurizing technology and manufacturing technology utilizing this technology, Japan will have a clear advantage over other countries in the world in the domain of nanoparticle engineering. The survey and research described in this report aim to review the trends of technologies for nanoparticle composition and functionalization and to clarify the course that Japan is to follow in the development of technologies concerned. (NEDO)

  8. Achievement report for fiscal 1998. Research and development of super-functional environment-resistant materials by controlling trace metal ion implantation; 1998 nendo seika hokokusho. Gokubiryo kinzoku ion chunyu seigyo ni yoru chokino taikankyo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim was to develop reliable materials high in resistance to hostile environments, greatly improved in their resistance to oxidation, abrasion, and corrosion at high temperatures. To achieve the goal, trace quantities of high melting point metals were implanted into the compound formed on the substrate surface or deep into the substrate material. This year's research and development is outlined below. Important technologies in the ion process involved materials which at high temperatures were very resistant to oxidation, abrasion, and corrosion. The high-temperature oxidation resistant material was studied for use with the automobile supercharger rotor. The study on the high-temperature abrasion resistant material involved Ti-N thin coatings: the optimization of coating conditions, slidability at room temperature, and slidability in a high-temperature atmosphere. As for the high-temperature corrosion resistant material, studies were made to use it for refuse-fueled power generation. The TiAl material was also studied: the effect of ion implantation on the improvement of its high-temperature oxidation resisting capability, analysis into oxidized alloy surface properties, ion implantation into complicatedly shaped items and the optimum material for them, and the surface treatment by ion beams for improving resistance to high-temperature corrosion. (NEDO)

  9. Achievement report for fiscal 1998. Research and development of nano-structural materials for ceramic bearing application (the second year); 1998 nendo seika hokokusho. Ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is made on ceramic bearing using high-performance and low-cost nano-structural materials, and its application is performed to high-quality bearings suitable for energy conservation in automobiles and industrial machines, and bearings for office automation devices, electronics, and aeronautic and maritime development. To achieve these goals, raw material synthesizing technologies, forming technologies, structural control technologies, processing technologies and mass production technologies shall be established. Fiscal 1998 had the following achievements: establishment of nano-structure controlled ceramic material powder synthesizing technology (nano-lamination type composite powder made by using the beads mill co-precipitation method, nano-lamination type composite powder made by using the New Mymill co-precipitation method, nano-lamination type composite powder made by using the controlled liquid phase method, composite nano-structured gel, and nano-powder synthesis); near net forming technology for spherical ceramics; high-speed processing technology for ultra smooth surface; evaluation of rolling fatigue properties of ceramic bearings; and analysis and evaluation of nano-structured materials. Since this alumina-based ceramic bearing can be produced at reduced cost with performance comparable to silicon nitride based bearing, investigations and discussions are being given on the application thereof. (NEDO)

  10. FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

  11. FY 2000 Development of technologies for optimization control of reducing power loss during the service period. Report on the research and development results of the 'building total cooperation control by micro-internet technologies'; 2000 nendo kadoji denki sonshitsu sakugen saiteki seigyo gijutsu kaihatsu seika hokokusho. Micro internet gijutsu ni yoru biru total kyocho seigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research and development project is implemented for development of the energy-saving optimization/control system which continuously monitors/controls all of the energy-consuming appliances in a building for their optimization, and the FY 2000 results are reported. The program for the sensing technologies involves a human tracking system aided by fish-eye images and human region sensing technologies based on the neuro technologies, and introduces an animated image simulation system aided by a personal computer. The researches on the building total cooperation control involve establishment of the system designs for controlling heat sources, based on the thermal loads predicted by the information network system. The researches on the micro-internet technologies involve development of the prototype unit which collects information from indoor environment sensors (e.g., for room temperature, luminous intensity and CO2 concentration), and interface devices which collect information from the sub-systems, e.g., air conditioners and heat sources. These systems are completed. The demonstration and assessment program involves designs of the instrumentation systems and network environments. The designs are completed, and various sensors and monitors are installed. (NEDO)

  12. FY 2000 Development of technologies for optimization control of reducing power loss during the service period. Report on the research and development results of the 'building total cooperation control by micro-internet technologies'; 2000 nendo kadoji denki sonshitsu sakugen saiteki seigyo gijutsu kaihatsu seika hokokusho. Micro internet gijutsu ni yoru biru total kyocho seigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research and development project is implemented for development of the energy-saving optimization/control system which continuously monitors/controls all of the energy-consuming appliances in a building for their optimization, and the FY 2000 results are reported. The program for the sensing technologies involves a human tracking system aided by fish-eye images and human region sensing technologies based on the neuro technologies, and introduces an animated image simulation system aided by a personal computer. The researches on the building total cooperation control involve establishment of the system designs for controlling heat sources, based on the thermal loads predicted by the information network system. The researches on the micro-internet technologies involve development of the prototype unit which collects information from indoor environment sensors (e.g., for room temperature, luminous intensity and CO2 concentration), and interface devices which collect information from the sub-systems, e.g., air conditioners and heat sources. These systems are completed. The demonstration and assessment program involves designs of the instrumentation systems and network environments. The designs are completed, and various sensors and monitors are installed. (NEDO)

  13. Development of high field magnets at the National Research Institute for Metals. Kinzoku zairyo gijutsu kenkyusho ni okeru kojikai magnet gun no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kiyoshi, T.; Inoue, K.; Maeda, H. (National Research Inst. for Metals, Tsukuba (Japan))

    1993-06-20

    Sinece 1988, the Scince and Technology Agency has initiated the superconductor multicore project, which has a purpose of the versatile study on the high temperature superconducting materials of the oxide series. The National Research Institute for Metals is in charge of 5 cores out of them, and in the performance evaluation core which is one of them, the development of each kind of the high field magnets is being advanced for evaluating the characteristics under the high magnetic field. As the magnets, including the 40T class hybrid magnet which generates the steady state magnetic field of 40T, the superconducting magnet of 20T with a large diameter which generates the magnetic field over 20T with a superconductor, the condenser bank system for the pulse magnet to generate the pulse magnetic field up to 80T, and the ultra-precise magnet system which generates the magnetic field with a high uniformity will be consolidated. Keeping pace with a removal of the National Research Institute for Metals to Tsukuba, the construction of the strong magnetic field station is being advanced in the Sakura area. These several kinds of magnets are scheduled to be used in turn for the international joint study. 33 refs., 5 figs., 4 tabs.

  14. Material revolution, and analysis of its impacts on the industry and technology of the next generation; Zairyo kakumei to jisedai sangyo gijutsu eno impact bunseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper discusses possibility of advanced materials from seeds and expectations from needs; and also describes consistency between the seeds and needs, and possible impacts of these materials on the industry and technology of the next generation. Chapter 1 presents the promising results and eventual possibilities, based on the basic studies, of the advanced materials, e.g., fine ceramics, highly functional polymers, new alloys and composite materials. Chapter 2 analyzes the properties and functions attainable by these materials, and expected applicable areas; investigates their technical and economical possibilities; and also investigates their ripple effects on the technology and economy. Chapter 3 investigates the current situations of the demands in the automobile, chemical plant and energy areas, and problems involved in development of these materials for these areas. Chapter 4 investigates the measures to promote consistency between the seeds and needs of these materials, and impacts of these advanced materials on the related techniques, related industries and industrial structures. Chapter 5 summarizes the problems and measures narrowed down in Chapters 1 to 4 comprehensively for the above areas; and the measures to be taken by the private sector, and cooperation by the industrial, government and academic circles. (NEDO)

  15. FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

  16. Fiscal 2000 research report on the research on materialss with functions enhanced by microcapsulation technology; 2000 nendo microcapsul ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research is conducted to create materialss equipped, thanks to microcapsulation, with a noise stopping function, vibration damping function, moisture adjusting function, electromagnetic shielding function, and the like, and usable as structural elements as is, that is, materialss known as 'interactive materialss.' For the development of an interactive materials, it is important to incorporate an element, which interacts with external energy, into the materials. A system using interactive materialss when embodied will ensure a safer and more comfortable daily life space. Taking this into consideration, in this fiscal year, studies are made about the technical representation of problems and troubles that jeopardize the safety and comfort of the daily life space, establishment of standards in this connection, interactive features to be realized using microcapsules, possibility of novel interactive characteristics using the same, techniques for the systematization of microcapsules as industrial materialss, techniques for assessing and analyzing materialss characteristics, simulation or the like of a safe and comfortable space using interactive materials-aided systems, and so forth. (NEDO)

  17. Research and development of the industrial basic technologies of the next generation, 'composite materials (quality evaluation techniques)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (hinshitsu hyoka gijutsu)'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing composite materials as the basic technologies of the next generation are evaluated, and the directions of the R and D evaluation for the second phase are set up. The efforts in the first-phase R and D project are aimed at development of methods for measuring carbon fiber surface structure elements; confirmation of the relationship between adhesive shear strength and active surface area; development of methods for determining fracture toughness by standard specimens; estimation of allowable void fraction for inter-layer shear strength; defect detection and quality evaluation by electromagnetic, ultrasonic, laser holography and AE methods; development of methods for detecting resin setting reactions during the molding processes; and understanding deteriorated mechanical characteristics of the resin-based composites by environmental factors, among others. The objectives of the first-phase project have been almost achieved. It is decided that the second-phase R and D project are directed to investigations on the relationship between surface properties of the fibers in the composites and fiber/matrix adhesion; researches on mechanical characteristics involved in fracture of the structural elements; evaluation of mechanical properties of the metal-based composites and investigations on detecting their defects; elucidation of the effects of environmental factors on their strength; and development of the techniques for integrating detection of molding-induced cracking and that of setting reactivity, among others. (NEDO)

  18. Fiscal 1999 leading research report. Research on advanced functional material technology based on micro- capsule technology; 1999 nendo micro capsule ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Study was made on production technology of the 5th- generation material 'eco-smart composite structure' based on micro-capsule technology. This material ought to have an intelligent function including self-detection and self- restoration of defects, environmental harmony, high strength and long life. At present, these demands are implemented by embedding a sensor, actuator and controller in structure, or optical fiber, shape memory alloy and computer chip in matrix, however, such complex material structure has adverse effect on environment. On the other hand, single structure material such as biodegradable polymer is unusable in severe environment such as the ocean and space. These problems can be resolved by combining composite material and micro-sphere technology, for example fiber-reinforced plastic (FRP) composite structure including micro-capsules with nano particles. According to targets, this material can have a self-restoration intelligent function, and other environment friendly functions such as easy decomposition, sound insulation, oscillation damping, electromagnetic shielding and hygroscopicity. (NEDO)

  19. Fiscal 1999 leading research report. Research on advanced functional material technology based on micro- capsule technology; 1999 nendo micro capsule ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Study was made on production technology of the 5th- generation material 'eco-smart composite structure' based on micro-capsule technology. This material ought to have an intelligent function including self-detection and self- restoration of defects, environmental harmony, high strength and long life. At present, these demands are implemented by embedding a sensor, actuator and controller in structure, or optical fiber, shape memory alloy and computer chip in matrix, however, such complex material structure has adverse effect on environment. On the other hand, single structure material such as biodegradable polymer is unusable in severe environment such as the ocean and space. These problems can be resolved by combining composite material and micro-sphere technology, for example fiber-reinforced plastic (FRP) composite structure including micro-capsules with nano particles. According to targets, this material can have a self-restoration intelligent function, and other environment friendly functions such as easy decomposition, sound insulation, oscillation damping, electromagnetic shielding and hygroscopicity. (NEDO)

  20. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  1. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

  2. Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

  3. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

  4. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

  5. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

  6. FY 1993 research and development of the technology for controlling structures of functional composite members. R and D of advanced surface processing for methane-fueled aircraft engine members (Technology for controlling the microscopic structures of superhigh-temperature members); 1993 nendo fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). Chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Described herein are the results of the FY1993 research and development project, implemented for development of the technologies for modification of material surfaces and interfaces, with the objectives to develop the optimum members for methane-fueled aircraft engines. For R and D of multi-layered films with controlled microscopic structures, the tests are conducted for forming thin-film layers by, e.g., ion implantation, ion mixing and implantation of large quantities of ions as the surface controlling/modification techniques based on, e.g., ionic techniques. The tests are conducted for, e.g., chemical vapor-phase reaction evaporation and low-pressure plasma spraying as the technologies for forming multi-functional films of, e.g., high reliability and resistance to corrosion. For development of the technologies for controlling/compositing the microscopic structures, the tests are conducted for, e.g., selection of the matrix materials, and prevention/removal of defects by the chemical vapor-phase reaction penetration treatment effected for extended periods. For development of the technologies for evaluation of the characteristics under superhigh-temperature environments, the tests are conducted to investigate the mechanical characteristics of isotropically uniform metallic materials under multi-dimensional stresses and evaluation thereof, and mechanical and thermal characteristics of carbon-fiber-reinforced carbon composites and evaluation thereof. (NEDO)

  7. Report on fiscal 1998 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (R and D on carbon-based high function material); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Results of R and D for the initial year were compiled concerning the frontier carbon technology R and D project started in fiscal 1998. In the material formation and evaluation studies of SAW (surface acoustic wave) elements, an AlN (aluminum nitride) film and a diamond/Si film were successfully formed by a nitrogen radical assisted pulsed laser vapor deposition method and a reactive DC magnetron sputtering method. Also performed were the simulation analysis of diamond SAW element characteristics and the evaluation studies of the SAW elements. In the development of the film forming and evaluation technologies of ultra thin carbon-based protective film, carbon-based thin films were developed using an ECR (electron-cyclotron resonance) sputtering method. In the development of evaluation technology for the abrasion performance of ultra thin carbon-based protective films, examination and experiment were carried out for the evaluation device and method capable of simulating abrasion performance in an HDD (hard disk drive). In the development of a high performance display device using a carbon nano tube cold cathode electron source, the evaluation of electron emission characteristics was conducted, as was the manufacturing of a RGB surface light source. (NEDO)

  8. Report on fiscal 1998 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (R and D on carbon-based high function material); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Results of R and D for the initial year were compiled concerning the frontier carbon technology R and D project started in fiscal 1998. In the material formation and evaluation studies of SAW (surface acoustic wave) elements, an AlN (aluminum nitride) film and a diamond/Si film were successfully formed by a nitrogen radical assisted pulsed laser vapor deposition method and a reactive DC magnetron sputtering method. Also performed were the simulation analysis of diamond SAW element characteristics and the evaluation studies of the SAW elements. In the development of the film forming and evaluation technologies of ultra thin carbon-based protective film, carbon-based thin films were developed using an ECR (electron-cyclotron resonance) sputtering method. In the development of evaluation technology for the abrasion performance of ultra thin carbon-based protective films, examination and experiment were carried out for the evaluation device and method capable of simulating abrasion performance in an HDD (hard disk drive). In the development of a high performance display device using a carbon nano tube cold cathode electron source, the evaluation of electron emission characteristics was conducted, as was the manufacturing of a RGB surface light source. (NEDO)

  9. FY 1991 report on the results of the surveys on the technologies for forming composite materials. Research and development of the new technologies for forming composite materials (Comprehensive surveys and researches); 1991 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This project is aimed at development of new technologies for forming composite materials by studying the methods for controlling structures of ceramic- and metal-based composite materials, and also at development of the technologies for forming near-net shapes utilizing the phenomenon of superplasticity. The literature survey is conducted to help promote the developments, and the abstracts of the major papers are pigeonholed into 4 general categories; (1) production and properties of ceramic-based composite materials, (2) superplasticity of ceramic-based composite materials, (3) production and properties of metal-based composite materials, and (4) superplasticity of metal-based composite materials. This paper summarizes the abstract of these papers. The category (1) includes carbon fiber reinforced Sialon composites produced by polymer pyrolysis, the category (2) includes superplasticity of functional ceramics, and comparison of tensile and compressive creep behavior of a superplastic yttria-stabilized zirconia-20 wt.% alumina composite, the category (3) includes in-situ metal matrix composite, and the category (4) includes high strain rate superplasticity in whisker-reinforced alumina composites, and application of superplasticity to fabrication of metal matrix composites. (NEDO)

  10. Fiscal 1992 survey report of R and D on new forming technology of composite material. Development of innovative technology for producing members for high efficiency power generation; 1992 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (kokoritsu hatsuden'yo buzai soseigijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Composite forming technology is being developed which is intended to manifest superplasticity phenomenon of ceramic matrix and metallic matrix composite materials; also being developed is an effective efficient superplastic processing technology which utilizes this composite forming technology. The related technologies were investigated comprehensively systematically with the purpose of promoting the development. First, an overview was given in the present state and problems of ceramic matrix/metallic matrix composite technologies and in the forefront of the superplasticity research of ceramic matrix materials, and then, the related technologies of these composite materials were pigeonholed under the following items: 1. assesment/strength/dynamic properties, 2. composite process and property, 3. composite forming process, 4. superplasticity, 5. process and superplasticity, and 6. others. The titles of the rearranged summary documents are, for example, surface modification and casting of SiC platelets in Al{sub 2}O{sub 3} composites, deformation of Al{sub 2}O{sub 3}/TiC composites at elevated temperatures, superplastic bulging of fine-grained zirconia, forging of short alumina fiber reinforced aluminum alloy, and on superplasticity in silicon carbide reinforced aluminum composites. (NEDO)

  11. FY 1992 Survey report of the technologies for creating/processing advanced biomaterials. Research and development of the technologies for creating/processing advanced biomaterials (Comprehensive survey and research); 1992 nendo senshin bio zairyo no sosei kako gijutsu chosa hokokusho. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (sogo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, item (6) peptide having activity with plant, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

  12. FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

  13. Fiscal 1992 survey report of R and D on new forming technology of composite material. Development of innovative technology for producing members for high efficiency power generation; 1992 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (kokoritsu hatsuden'yo buzai soseigijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Composite forming technology is being developed which is intended to manifest superplasticity phenomenon of ceramic matrix and metallic matrix composite materials; also being developed is an effective efficient superplastic processing technology which utilizes this composite forming technology. The related technologies were investigated comprehensively systematically with the purpose of promoting the development. First, an overview was given in the present state and problems of ceramic matrix/metallic matrix composite technologies and in the forefront of the superplasticity research of ceramic matrix materials, and then, the related technologies of these composite materials were pigeonholed under the following items: 1. assesment/strength/dynamic properties, 2. composite process and property, 3. composite forming process, 4. superplasticity, 5. process and superplasticity, and 6. others. The titles of the rearranged summary documents are, for example, surface modification and casting of SiC platelets in Al{sub 2}O{sub 3} composites, deformation of Al{sub 2}O{sub 3}/TiC composites at elevated temperatures, superplastic bulging of fine-grained zirconia, forging of short alumina fiber reinforced aluminum alloy, and on superplasticity in silicon carbide reinforced aluminum composites. (NEDO)

  14. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

  15. Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

  16. FY 2000 report on the survey on the long-term energy technology strategy. Fundamental survey to work out industrial technology strategies (technology strategy by field - material technology field); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of constructing the material technology strategy, conducted were study of the trend of technical development, arrangement of material technology seeds, and survey of the R and D environment. Concretely, the paper carried out the grasp of the national projects related to materials in Europe and the U.S., patent registration (U.S.-Japan comparison)/application (Europe/Japan), transfer of technology trade, and survey of the trend of papers made public in scientific magazines. Further, in the survey of the R and D environment, conducted were how to treat researchers/engineers, how to handle intellectual ownership, system to promote the cooperation among industry/university/government, and comparison among countries in policies of technology such as patent strategy. The results of the survey were classified into the following 4 items: 1) trend of the technical development in the material technology field; 2) developmental environment in the material technology field; 3) competitive force in the material field and material user needs/seeds maps; 4) proposal for the material technology strategy. As to the competitive force of material technology in 3), the paper took up organic/polymer, iron/steel, aluminum, semiconductor, and ceramic materials. (NEDO)

  17. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  18. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - material technology field (nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bunya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the nonferrous metal field relating to the FY 1999 long-term energy technology strategy. The needs for electronics products are increasing toward the 21st century. Domestically the competition with other countries in enlarging the market share has been intensifying. At the same time, the smaller the size of device becomes, the more the barriers in technology to be overcome increase. In the development of Si wafer to cope with such a situation, there are a lot of problems to be broken down in liaison with industry/government/university. Compound semiconductors are higher in speed than Si, and have a marked feature of producing light, but are difficult in crystal growth. It was in the past 20 years that the development of commercialization technology has rapidly advanced. Compound semiconductors are indispensable as a device in the energy problem which strongly influences the global environment. In the U.S., for the military use, a policy for upbringing national industries has been carried out since 1993. The role of compound semiconductor materials playing as the fundamental industry which supports the semiconductor industry and system industry as the nation's core industries is important even in Japan the same as in the U.S. (NEDO)

  19. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - material technology field (nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bunya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the nonferrous metal field relating to the FY 1999 long-term energy technology strategy. The needs for electronics products are increasing toward the 21st century. Domestically the competition with other countries in enlarging the market share has been intensifying. At the same time, the smaller the size of device becomes, the more the barriers in technology to be overcome increase. In the development of Si wafer to cope with such a situation, there are a lot of problems to be broken down in liaison with industry/government/university. Compound semiconductors are higher in speed than Si, and have a marked feature of producing light, but are difficult in crystal growth. It was in the past 20 years that the development of commercialization technology has rapidly advanced. Compound semiconductors are indispensable as a device in the energy problem which strongly influences the global environment. In the U.S., for the military use, a policy for upbringing national industries has been carried out since 1993. The role of compound semiconductor materials playing as the fundamental industry which supports the semiconductor industry and system industry as the nation's core industries is important even in Japan the same as in the U.S. (NEDO)

  20. Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

  1. Report on achievements of research and development of an automatic sewing system in fiscal 1985. System management and control technology; 1985 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    This paper describes the system management and control technology, extracted from the achievement report for fiscal 1985 on developing an automatic sewing system. The comprehensive system management has verified algorithms for the optimal process formation and load balancing based on the industry's latest market and production plan trends, and obtained good results. Furthermore, structuring, discussions and proposals were made on an interface system of an optimal process controlling computer with an automatic device controlling micro computer. The inspection and failure diagnosis have set a quality standard for intermediate products in the sewing lines, and verified that its automation is possible by using an image processing technology that identifies dimensional inspection and colors. In the research of printing control information, calculations were performed on the information amount, printing locations, expression method and printing speed, narrowing down to parts ID and location information as the required printing information. Thus,items of basic information for media, media printing and printing device design were put into order. The information recognizing technology has picked up image recognition applying locations in a sewing factory and problems therein, and performed evaluation experiments on specific pattern matching and processing position recognition to have obtained the prospect of application of the automation. (NEDO)

  2. FY 1999 Report on research and development project. Research and development of high-temperature air combustion technology; 1999 nendo koon kuki nensho seigyo gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The high-temperature air combustion technology recently developed greatly advances combustion technology. The technology, when applied to the other areas, may expand its applicable areas and contribute to environmental preservation, e.g., abatement of CO2 emissions. This is the motivation for promotion of this project. The combustion technology, developed by improving functions of industrial furnaces, cannot be directly applied to the other combustion heaters. This project is aimed at extraction of the problems involved, finding out the solutions, and thereby smoothly transferring the technology to commercialization. This project covers boilers firing finely pulverized coal, waste incineration processes and high-temperature chemical reaction processes, to which the new technology is applied. It is also aimed at establishment of advanced combustion control basic technology, required when the high-temperature air combustion technology is applied to these processes. In addition to application R and D efforts for each area, the basic phenomena characteristic of each combustion heater type are elucidated using microgravity and the like, to support the application R and D efforts from the basic side. This project also surveys reduction of environmental pollutants, e.g., NOx and dioxins. This report presents the results obtained in the first year. (NEDO)

  3. Control of surface wettability by light illumination: surface wettability control utilizing photo-induced surface reaction of titanium oxide; Hikari de nure wo seigyosuru - sanka chitan no hikari reiki hanno wo riyoshtia nure seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Hashimoto, K. [The Universityof Tokyo (Japan)

    1999-02-15

    We report photo-generation of highly hydrophilic surface of titanium dioxide. The photo-induced hydrophilicizing is achieved by photo-generation of Ti{sup 4+} to Ti{sup 3+} at definite sites on the surface, resulting in preferential adsorption of hydroxyl groups on corresponding oxygen vacant sites. We also report the photo-generation of titanium dioxide amphiphilic surface on definite photo illumination condition. The unique character of this surface is ascribed to the microstructure of hydrophilic and oreophilic domain. The hydrophilic or amphiphilic titanium dioxide coating can be applied for antifogging mirror or glass and also self-cleaning paint for various industrial materials. Several commercial applications including antifogging automobile side-view mirror or self-cleaning exterior ceramic tile has been starting to hit the market. (author)

  4. Report on achievements of research and development of an automatic sewing system in fiscal 1986. System management and control technology; 1986 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The Automatic Sewing System Technology Research Association was commissioned from the Agency of Industrial Science and Technology on the 'development of an automatic sewing system'. The association is performing the research and development by dividing the subject into such component technologies as a total system and sewing preparation and processing technology, a sewing and assembling technology, a cloth handling technology, and a system management and control technology. This paper reports the achievement of the research and development on the system management and control technology. Plans have been established on the following items: dimensional inspection of sewn parts by using an image processing technology, real-time processing of the matching work interlocked with a striped pattern cloth handling device, and a processing positioning algorithm to instruct sewing lines and needle dropping points based on contour lines of pockets and collars. The effects thereof were verified. Printing seven-segmented numerals on cloth by using fluorescent whitener and an automatic reading test of the printed information verified that the technology can be applied to tracking the parts in a processing line as an ID information. Researches were also made on unification of micro-computers for controlling such automatic machines as a multi-functional sewing machine, a three-dimensional sewing machine, and a cloth handling and positioning device, as well as on interface with the computer for function sharing management and control. (NEDO)

  5. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  6. Fiscal 1999 international cooperation project report. R and D on convection control technology of glass melts by microgravity experiment; 1999 nendo bisho juryoku kankyo wo riyoshita glass yuekinai tairyu seigyo gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This R and D aims at development of convection simulation technology of glass melts based on measurement of accurate glass melt properties, and development of convection control technology of glass melts through the model experiment and small tank furnace experiment. Experiment was made on measurement of surface tension while levitating glass melts under the microgravity condition obtained by the drop tower of Japan Microgravity Center in Hokkaido. The shape of glass melt changes into a real sphere under the microgravity condition, and surface tension can be obtained by measuring its frequency, however, such frequency of glass could not be measured in this experiment. Levitation, fusion and oscillation experiment of glass was carried out by using an aero-acoustic levitator of CRT at Chicago. The experiment result is now in analysis. This study also aims the analysis in consideration of a surface tension flow effect. The calculation result showed generation of surface tension flow due to temperature gradient on a liquid surface. Various information were obtained through the model experiment using silicon oil, and glass convention observation by using a small tank furnace. (NEDO)

  7. Development of large scale wind energy conservation system. Development of control techniques for assembly-type wind power generating systems; Ogata furyoku hatsuden system no kaihatsu. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for development of control techniques for assembly-type wind power generating systems. The study on optimum system configuration produces 50 to 100kW wind power units for screening small-size wind power plant types, and, at the same time, surveys performance of commercial units and experiences of 9 makers capable of producing the above units. As a result, 3 MICON`s units (output: 100kW, active YAW control, monopole tower, maximum wind speed: 60m/s) are selected. The study on optimum operational techniques integrates 2 medium-size power units into a power line, showing a service factor of 30.2% on the annual average, monthly varying in a range from 11.8 to 45.0%. These units, installed in Miyako Island, were attacked by 3 typhoons of wind velocity of 25m/s or higher in 1994, and the only damage recorded is that of the anemoscope/anemometer. It is found that No.1 unit is located at a better geographical point than the No.2 unit, to produce a higher output. 3 figs., 3 tabs.

  8. Fiscal 1999 achievement report. Research and technology of important regional technologies (Development of combustion control system technology for rationalizing energy use); 1999 nendo energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For upgrading and optimizing combustion control systems, research and development is conducted for materializing SiC devices capable of high-temperature operation. In the development of basic technologies common to various types of SiC semiconductor devices, XeCl excimer laser annealing is applied to SiC implanted with Al ions, and low-damage ion implantation is studied. In the development of techniques for forming SiC single crystals into substrates, warpage of 20{mu} or less, surface coarseness of 5{mu}m or less, etc., are achieved in 1-inch and 2-inch wafers. In the development of SiC sensor technology, techniques of heteroepitaxial growth of 3C-SiC on Si substrates and of 6H-SiC on 6H-SiC wafers are established and an optical sensor is built experimentally. A high-temperature UV sensor, switching device for control, rectification device for control, etc., are built of nitrogen ion implanted 6H-SiC. In the effort to develop combustion control system technology, the principle of system operation of the combustion control method proposed under this project is verified. (NEDO)

  9. Achievement report for fiscal 1998. Development of control system technologies such as combustion with energy consumption rationalized; 1998 nendo seika hokokusho. Energy shiyo gorkika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To improve and optimize fuel control systems, basic technologies were studied for building SiC devices capable of high-temperature operation. The technologies involved the construction of single-crystal SiC substrates, development of element technologies such as conduction control, experimental production of SiC devices, and systems incorporating SiC devices for controlling, for example, combustion. The subjects of research and development for fiscal 1998 included the technologies related to common SiC semiconductor substrates (SiC substrate crystallinity evaluation by X-ray topography, thermal oxidation acceleration by ion irradiation, and annealing of ion-implanted SiC by excimer laser ), technologies of forming an SiC single crystal into a substrate, technologies related to SiC sensors, technologies related to SiC devices capable of operation at high temperature and high speed, technologies related to SiC devices for controlling, and technologies for controlling, for example, combustion. The subjects of basic researches at universities and research institutes included new crystal growing methods, ion beam-aided SiC synthesis, effect of irradiation of SiC with neutrons, and nuclear conversion implantation. (NEDO)

  10. FY 1984 annual report on the research and development of automatic sewing systems. System management/control techniques; 1984 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    The automatic sewing system technique research association has been commissioned by the Agency of Industrial Science and Technology for (research and development of automatic sewing systems). This program covers R and D of the elementary techniques for total systems and sewing preparation/processing, sewing/assembling, cloth handling, and system management/control. This report describes the results of the R and D efforts for the system management/control techniques. The FY 1984 efforts are directed to the basic designs for optimizing process configurations, load balances, and control of sewing/assembling devices, transfer devices and the like using a computer for controlling purposes, based on the production schedules in which demand forecasts by apparel makers are reflected, in order to reduce lead time from charging cloth into an automatic sewing plant to delivery of the products by at least 50% from the current level by improving processing efficiency and speed. The plan for development of the examination/failure diagnosis method, as the next R and D theme, is drawn mainly for determining positions of product quality standard setting-up, examination of individual steps and failure diagnosis functions of sewing machines, classification of the failure levels, and prediction of failure. Prospects of establishing an automatic system for visual recognition are obtained. (NEDO)

  11. Fiscal 2000 survey report. Development of nucleation control technology for new functional alloy creation and development of new process; 2000 nendo kinosei shingokin sosei no tame no kaku seisei seigyo gijutsu kaihatsu oyobi shin process kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the above-said purposes, studies were conducted involving the construction of a database on supercooling and nucleation and on alloy species and functionality. Composition, concentration, supercooling method, container, atmosphere, maximum degree of supercooling, cooling rate, and the contents of the study to be made were investigated in the study of items for databasing. Also, in an experiment dealing with alloy species remaining to be exploited, the coagulation of drop size GaSb alloy was investigated. In the study of the formation of a quasi-stable phase in functional alloy, it was demonstrated that a nonequilibrium or quasi-stable phase might be quantitatively formed by use of a containerless process. In the study of texture control, texture fining by causing flowability was particularly investigated, and it was suggested that not only nucleation but also growth to follow should be properly controlled for the fining of coagulated texture. In the study of simulation of texture prediction, construction of a database on practical alloy nucleation frequency and stochastic simulation of coagulated texture to be built on this database were taken up. (NEDO)

  12. FY 1999 Report on research results. Research and development of high-temperature air combustion technology (Attachments); 1999 nendo koon kuki nensho seigyo gijutsu kenkyu kaihatsu seika hokokusho. Shiryoshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project surveys the actual conditions of dioxins emissions discharged from the waste incinerators in commercial service, in order to establish the database for evaluating the effects when the (high-temperature air combustion technology) is applied to waste incinerators. The survey covers 1018 totally continuous incinerators and 724 quasi-continuous incinerators in service in Japan, and the data are analyzed by incinerator types and items for correlating each element with one another, based on The Waste Incinerator Register issued by The Wastes Research Foundation and Dioxins Concentrations in Flue Gases from General Waste Incinerators issued by Health and Welfare Ministry. For 1105 mechanized batch type combustion furnaces and 159 stationary batch type combustion furnaces, only discharged dioxins concentrations are analyzed by incineration capacity. The attachments include (1) report on the survey results of the actual conditions of dioxins emissions, (2) report on the survey results of the actual conditions of dioxins concentrations in flue gases discharged from general waste incinerators, (3) report on the survey results of the actual conditions of NO emissions discharged from sewer sludge incinerators, and (4) and (5) report on the survey results of the actual conditions of NO emissions discharged from fluidized bed type general waste incinerators. (NEDO)

  13. Report on achievements of research and development of an automatic sewing system in fiscal 1985. System management and control technology; 1985 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    This paper describes the system management and control technology, extracted from the achievement report for fiscal 1985 on developing an automatic sewing system. The comprehensive system management has verified algorithms for the optimal process formation and load balancing based on the industry's latest market and production plan trends, and obtained good results. Furthermore, structuring, discussions and proposals were made on an interface system of an optimal process controlling computer with an automatic device controlling micro computer. The inspection and failure diagnosis have set a quality standard for intermediate products in the sewing lines, and verified that its automation is possible by using an image processing technology that identifies dimensional inspection and colors. In the research of printing control information, calculations were performed on the information amount, printing locations, expression method and printing speed, narrowing down to parts ID and location information as the required printing information. Thus,items of basic information for media, media printing and printing device design were put into order. The information recognizing technology has picked up image recognition applying locations in a sewing factory and problems therein, and performed evaluation experiments on specific pattern matching and processing position recognition to have obtained the prospect of application of the automation. (NEDO)

  14. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  15. Report on achievements of research and development of an automatic sewing system in fiscal 1986. System management and control technology; 1986 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    The Automatic Sewing System Technology Research Association was commissioned from the Agency of Industrial Science and Technology on the 'development of an automatic sewing system'. The association is performing the research and development by dividing the subject into such component technologies as a total system and sewing preparation and processing technology, a sewing and assembling technology, a cloth handling technology, and a system management and control technology. This paper reports the achievement of the research and development on the system management and control technology. Plans have been established on the following items: dimensional inspection of sewn parts by using an image processing technology, real-time processing of the matching work interlocked with a striped pattern cloth handling device, and a processing positioning algorithm to instruct sewing lines and needle dropping points based on contour lines of pockets and collars. The effects thereof were verified. Printing seven-segmented numerals on cloth by using fluorescent whitener and an automatic reading test of the printed information verified that the technology can be applied to tracking the parts in a processing line as an ID information. Researches were also made on unification of micro-computers for controlling such automatic machines as a multi-functional sewing machine, a three-dimensional sewing machine, and a cloth handling and positioning device, as well as on interface with the computer for function sharing management and control. (NEDO)

  16. FY 1983 annual report on the research and development of automatic sewing systems. System management/control techniques; 1983 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    The automatic sewing system technique research association has been commissioned by the Agency of Industrial Science and Technology for (research and development of automatic sewing systems). This program covers R and D of the elementary techniques for total systems and sewing preparation/processing, sewing/assembling, cloth handling, and system management/control. This report describes the results of the R and D efforts for the system management/control techniques. The program for the system management/control techniques involves, first of all, the basic designs for the overall system management, centered by the optimum process configuration and control for reducing lead time of an automatic sewing plant by at least 50% from the current level, based on the production schedules of an apparel maker. The basic designs are then extended to cover examination of defective products at each step, examination and failure diagnosis for prediction, detection and exchange of failed machine parts, systemisation of necessary information to be provided for automatic operation of a sewing plant and providing control-related information, including selection of information media, and information recognition by processing images of cloth and surface conditions/shapes of machine parts. (NEDO)

  17. FY1987 report on the result of the R and D of an automatic sewing system. System management/control technology; 1987 nendo jido hosei system no kenkyu kaihatsu seika hokokusho. System kanri seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The paper summarized the R and D of system management/control technology which is an element technology of an automatic sewing system by the Automatic Sewing System Technology Research Association. The effects were confirmed by experiments such as the inspection of dimensions of sewing parts using image processing technology, inspection of the surface state to examine if or not there are darts and pintucks, making and demonstration of the recognition treatment software for fitting patterns on the pocket with big cross stripes, strengthening of the function to determine processing position, etc. Improvement was added to 7 segment letters which becomes ID information so that 8mm letters could be read at a recognition rate of more than 95%. The information required for production plan was summarized after making it mutually connected. Further, a method was worked out for estimation of the standard time required for making the day schedule. Files for drawing-up the optimum process and for process control simulator were made by the expression peculiar to apparel. The framework of the interface was prepared to make the following clear: the integration of the process control use computer into the microcomputer for control of automatic machines such as devices and presses for sewing preparation, multi-functional sewing, assembly sewing, cloth handling/positioning, and the sharing of functions. (NEDO)

  18. Fiscal 1999 research report on long-term energy technology strategy. Pt. 2. Basic research on industrial technology strategy (Individual technology strategy.) Material technology field (Fine ceramics); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. 2. Sangyo gijutsu senryaku sakutei kiban chosa (bun'ya betsu gijutsu senryaku) zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the basic research result on industrial technology strategy for a glass field. Japan is facing such various economic problems as attack by developing countries, collapse of economic babble and yen's appreciation, and environment problems over a period of several years, and a glass industry is also under the influence of such problems. For continuous development of Japan and improvement of the international competitiveness of Japan, development of a glass industry is essential. Both co- possession of technical issues by cooperation of the members, and breakdown of conventional structures of the industry are necessary. Clarification of technical issues, and cooperation of industry, academia and government is essential. The current state, promise and issues of domestic and overseas glass technology and its R and D are described. The joint target of an industrial strategy for researchers and engineers of every sector, and the approach to such target are showed from the viewpoint of the issues for Japan and preparation of common basic technology. The role of each sector for environment preparation and policy is described to achieve the target. (NEDO)

  19. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Part 1. Technology strategy by field - material technology field (fine ceramics technology field); 1999 nendo choki energy gijutsu senryaku ni kansuru chosa. 1. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the fine ceramics technology field relating to the FY 1999 long-term energy technology strategy. The fine ceramics industry is a new industry for which the future development is expected. It has far-reaching effects on other industries. Japan has the advantage over other countries. As subjects to remarkably develop the industry, needed are the long-term basic preparation which promotes technology innovation such as the promotion of the fundamental/creative R and D, construction of an industry/university liaison system, and arrangement of the intellectual base. Preparation of the competitive environment and promotion of policies paying attention to the market are needed which make the development under the private control by creative study/corporate activities possible. Also important are the demonstration of leadership and secure international competitive force in the light of Japan's international position. For the private-control development, the role and course of various groups should be made clear from a long-term aspect. It is desirable that university/government will newly develop innovative technology, and industry will make the present technology force more developmental and competitive. Support from the nation is requested for researches large in scale. (NEDO)

  20. Fiscal 1997 survey report / R and D of important region technology. R and D of technologies giving multi-functional characteristics to C/C composites (development of high-grade surface processing technology for engine members for methane fueled air craft. 1. control technology of micro structures of ultra-high temperature members); 1997 nendo seika hokokusho juyo chiiki gijutsu kenkyu kaihatsu. Fukugo kino buzai kozo seigyo gijutsu no kenkyu kaihatsu (methane nenryo kokukiyo engine buzai no kodo hyomen kako gijutsu kaihatsu). 1. chokoon buzai micro kozo seigyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing members most suitable for aircraft use engines with methane as fuel, the R and D were conducted of technology to reform surfaces and interfaces of materials. In the R and D, the paper took up carbon fiber reinforced carbon composite materials (C/C composites). In the surface control and reformation technology using the ion engineering method, etc., in the sealing processing of C/C composites, tried was the formation of a C/SiC/Si3N4 composite layer which was formed by Si3N4 much smaller in thermal expansion coefficient than SiC. Further, technologies on ion injection, thin film formation, giving of oxidation resistance/corrosion resistance, improving/giving of thermal shock resistance, etc. In the multi-functional coating formation technology such as high liability and corrosion resistance, the study was carried out of the dense composite functionally-gradient layer as thermal stress relaxation layer and the fiber reinforced layer by carbon fiber using pores. Besides, studies were made of technologies of the micro structure control combination, evaluation of ultra-high temperature resistant environmental characteristics, etc. 61 refs., 198 figs., 44 tabs.

  1. Fiscal 1996 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies were described of creating original high-functional materials. The paper presented the following two as fields of technology on which importance is to be placed for the future R and D from technological and socioeconomic points of view. In the field of new materials of living organism imitation type, remarkably high-performance/high-functional new materials are invented by imitating the precise function manifestation mechanism of the ultimate living organism in which a great variety of matters are in harmony with each other and manifest complicated and high-level functions. In the field of structural control/synthesis process technology, the paper is aimed at manifestation of newer and higher functions/performance and innovation of the synthesis process, and also at developing technology to precisely control structure and process of materials including surface and interface in correspondence with atomic/molecular to macro levels. Up to the present, conducted were an examination of autonomous response materials (the subtheme is a R and D of polymer/composite multi-stimuli-responsive materials) and a R and D of precise polymerization (control) polymer materials. 239 refs., 129 figs., 49 tabs.

  2. Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

  3. FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of materials for the coal liquefaction plant); 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sekitan ekika plant zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    A 1 T/D solvent-extraction type coal liquefaction test plant was constructed and operated to obtain the technical data for the design of, and establish the techniques for, an efficient coal liquefaction plant. The FY 1980 program includes surveys on the materials for coal liquefaction plants, covering those already developed and under development, to clarify the problematical points; drafting the test schedules; and conceptual designs of the material testing facilities. The major problems involved in the materials for coal liquefaction plants include erosion by fluidizing coal slurry, hydrogen embrittlement of the reactor materials, and corrosion by the liquefaction products (e.g., stress-corrosion cracking of austenitic steel, and corrosion by organic acids). The surveys on materials research trends suggest that USA seems to concentrate their research efforts on the reactor materials. The corrosion tests are mostly of in-plant tests, but the stress corrosion and slurry erosion tests are conducted on a laboratory scale. The conceptual designs are drawn for some testing units, e.g., the loop type material testing unit and basic testing unit for jet-spray type slurry erosion. (NEDO)

  4. Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

  5. Achievement report for fiscal 1999. Research and development of high-performance magnetic materials creation technology making use of microgravitational environment; 1999 nendo bisho juryoku kankyo wo riyoshita koseino jisei zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to develop the above-named technology so as to improve on performance of magnetic materials for magnets extensively used in electric motors to consequently influence their energy conversion efficiency. For this purpose, probes are conducted into novel alloy phases, intermetallic compounds, and microstructure in a containerless coagulation process in which a molten body of a magnetic metal material in free-fall is allowed to cool rapidly, and a system is developed to enable a series of processes of heating and melting in preparation for containerless coagulation, specimen formation, and then coagulation in a microgravitational environment. The system is used for the study of novel materials for magnetic alloys and process technology. For the utilization of containerless coagulation in a microgravitational environment, it is necessary to make full use of the JAMIC (Japan Microgravity Center) facilities, and an experimenting apparatuses are fabricated for a containerless coagulation process and unidirectional coagulation process applicable to a free-fall test. In this fiscal year, some significance involving for example structural uniformity are found among the specimens created using containerless coagulation in a microgravitational environment, and it is inferred that the data as an index of higher performance will lead to studies in the next fiscal year and afterward. (NEDO)

  6. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

  7. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  8. Research and development of the industrial basic techniques of the next generation. Composite materials (Final research and development evaluation / Part 1); Jisedai dangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (Saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This R and D project is aimed at development of highly functional materials for aerospace devices, bringing into focus research and development of resin-based composite materials (FRPs), metal-based composite materials (FRMs), and evaluation of their properties and their design techniques. The basic target properties are heat resistance temperature of 250 degrees C or higher and tensile strength of 240 kg/mm{sup 2} or more for the FRPs, and heat resistance temperature of 450 degrees C or higher and tensile strength of 150 kgf/mm{sup 2} or more for the FRMs. This R and D program has been implemented for 8 years for development of raw materials, molding/processing techniques, quality evaluation and designs through information exchange and discussions of the experts in each area under integrated, close cooperation from raw materials to molding/processing. Most of the data indicate that the target properties and objects are satisfied or exceeded. It is therefore concluded that this project for the composite materials, extending for 8 years in 3 phases, has sufficiently achieved the initial objects. The unique techniques are incorporated in the raw materials, molding/processing processes, quality evaluation and designs. These efforts have produced the FRPs and FRMs of the world highest qualities. (NEDO)

  9. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  10. Achievement report on research and development of the industrial basic technologies of the next generation in fiscal 1981. Research and development of composite materials; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Fukugo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Described herein are the results of the FY 1981 research and development for composite materials, established by the R and D system for the basic technologies of the next generation. The R and D project for resin-based composite materials involves basic researches on the matrix resins, and surface modification of the reinforcing fibers. The investigations and basic tests are conducted for monolithic molding, other types of molding, and cutting and boring by, e.g., laser beams and water jet. The other related efforts include researches on analysis theories for optimization of strength and rigidity of the composite structures, and development of the optimization programs. For the R and D project for the metal-based composite materials, the efforts are directed to understanding wettability and reactivity of the reinforcing fibers with metals, and development of the techniques for producing various types of preforms and compositing methods. The basic researches are conducted for hot pressing/rolling molding, extrusion/withdrawal, powder molding and melt molding of the composite materials with aluminum alloys as the matrices. The other R and D items include investigations on methods for evaluating qualities for the steps form the stock preparation to production of the final products. (NEDO)

  11. FY 1992 Report on results of the research and development of the technologies for creating/processing advanced biomaterials; 1992 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a metal or synthetic resin substrate with layered peptide synthesized to contain unusual amino acid. A total of 9 areas are investigated; (1) designs of peptide structures/functions, (2) technologies for controlling conformers, (3) peptide with photoelectric conversion functions, (4) enzyme-aided synthesis of peptide, (5) methods for introducing unusual amino acid into peptide, (6) substrate forming technologies (immobilizing peptide and putting it one on another on the substrate), (7) substrate modifying technologies, (8) reagent for binding peptide to the substrate, and (9) technologies for creating and stabilizing biomaterials with molecule-recognition functions. The item (1) involves structural analysis of imidazoline compounds with a microphage-migrating activity, and understanding the relationship between the steric structures and physiological activity, to start screening the peptide design procedures. The item (2) involves control of peptide conformers by substituting part of conformer-controlled amino acid which constitutes peptide. The item (3) selects the method for synthesizing amino acid substituted with a squarylium pigment. (NEDO)

  12. Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial; 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    R and D was conducted on a bio-functional material that is formed by synthesizing non-natural amino acids required for the manifestation of the function, incorporating the amino acids into new bio-functional peptides to be synthesized, and fixing the peptides on a substrate such as plastics. Activities were carried out in three areas, which were (1) innovative technologies for producing functional molecules, (2) R and D on materialization technologies of functional molecules: technique of pattern formation by photochemical reaction and of fixation, and technique of preparing peptide film using vacuum thin film forming technology, and (3) comprehensive investigation and adjustment. In (1), migration stimulating activity for microphage was selected as a molecular recognition evaluation system, and on the basis of the structural analysis result of a non-peptide compound/imidazolin compound having migration stimulating activity, molecular structural design was carried out for peptides having migration stimulating activity. The result of the analysis revealed that the spatial arrangement of three phenyl nuclei and the presence of basic structures were important. Among the 22 peptides so designed, only Cbz-Phe-Phe-His-NH{sub 2} showed the migration stimulating activity. For the design, a peptide molecule design system CHARMm/QUANTA/PM3 was used. (NEDO)

  13. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  14. FY 1992 Report on results of the research and development of the technologies for creating/processing advanced biomaterials. Part 2; 1992 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. 2. Sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the materials which show functions in a living body by coating a substrate of, e.g., silica or glass, with layered novel peptide synthesized to include unusual amino acid required to have the functions. The existing peptide-related technologies are reviewed and the natural peptide list is prepared. A total of 15 literature is surveyed, and the contents are pigeonholed into 8 items; (1) prospects of peptide engineering, (2) designs of peptide structures, (3) technologies of peptide synthesis, (4) synthesis of unusual amino acid and inclusion into peptide, (5) analysis of peptide structures, (6) physiological activity of peptide, (7) development of peptide materials and function manifestation, and (8) information retrieval of natural peptide (comprising 30 amino acids or less). The item (2) involves analysis and prediction of hydrophobicity of oligopeptide, item (3) chemical synthesis of protein, and protease-aided condensation of dipeptide, and item (7) solar cells based on a photoelectric conversion material and pigment-sensitized colloidal titanium oxide. (NEDO)

  15. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzokukei)'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-31

    The results of the first phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to understanding the basic characteristics regarding wettability and reactivity of PAN-based carbon fibers and PCS-based silicon carbide fibers with metals, in which aluminum-based matrices are considered; preliminary tests for various composting methods; and development of wire preforms as the intermediate materials. Bright prospects have been obtained for improving problems involved in each technique. For development of molding/processing techniques, basic researches have been conducted for hot pressing/rolling, extrusion/withdrawal, powder molding and melt molding, using various reinforcing fibers. Bright prospects have been also obtained for combinations of adequate molding processes for individual materials. For development of design techniques, the basic data regarding mechanical characteristics of FRMs, both domestic and foreign, are collected, and analyzed by the trace tests with specimens, to set up the targets for FRM function improvements, viewed from the designs. (NEDO)

  16. Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the second phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei). Dainiki hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-31

    The results of the second phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. The second phase (FY 1983 to 1986) project is carried out to achieve the objectives, which are set up based on the objectives for the basic designs and the results of the first phase project. As a result, the concrete (promotion objectives), including those related to mechanical characteristics, have been almost achieved. For development of the highly functional FRP materials, the R and D efforts are directed to improvement of their moldability while satisfying the requirements of high functions, e.g., resistance to heat, leading to development of the basic techniques for epoxy resin-based intermediate materials. These results indicate possibility of commercialization of highly heat-resistant polyimde resin-based and novel resin-based intermediate materials. The results of the novel molding/processing methods, taken up in the second phase project as the ones which use no autoclave, are rated that they are developed to suggest possibility of the eventual commercialization, although the products they give are not always showing sufficient mechanical properties. (NEDO)

  17. Research and development of basic technologies for next generation industries, 'high crystalline polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo (dainiki kenkyu kaihatsu kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This research and development is intended to establish a basic technology related to high crystalline polymeric material that has dynamic properties comparable to metallic materials by single polymeric material as a structural material. Thick and large high-elasticity molded forms were obtained by searching poly-arylate material, and by developing such processing technologies as high-pressure injection molding, composite injection molding, and elongation fluidity molding. High-elasticity molded forms with uniform internal orientation were obtained by heating and molding liquid crystal polymers under high magnetic field. Solution molding was performed on a molecular composite consisting of rigid chains and soft chains, which was laminated and bonded to have obtained an isotropic form with as high elasticity as 54 GPa. In addition, high pressure powder formation of cross-linked polymers of di-acetylene system provided an isotropic form with sound wave elasticity of 23 GPa.

  18. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The research and development in the second term included development of raw materials, elucidation of electricity conduction mechanism, and development of methods to improve stability and a new processing method. Crystals of a large number of charge migrating complexes were grown to elucidate their electron properties and structures. A theoretical model was structured for the superconduction mechanism in the charge migrating complexes. Poly-p-phenylene vinylene-based polymers achieved {sigma}=1.1 times 10{sup 4}s/cm as a result of extension of soluble reaction intermediates. Poly-2, 5-phenylene vinylene doped with FeCl{sub 3} retained 10{sup 3}s/m for 165 days in nitrogen. Polypyrrole achieved 3.0 times 10{sup 3}s/cm in constant potential electrolytically oxidizing polymerization and extension at low temperatures. Polypyrrole doped with ClO{sub 4}{sup -} retained electric conductivity of 85% for 400 days in nitrogen. Electric conductivity of higher than 10{sup 5}s/cm was obtained by applying different kinds of doping into thin film and fiber formed graphite. The world's highest conductivity of 9 times 10{sup 5}s/cm was achieved particularly with discharge laminated and polymerized graphite doped with AsF{sub 5}. (NEDO)

  19. Fiscal 1999 achievement report on interuniversity coordination type research and development of industrial technology. Research and development of highly functional material designing platform; 1999 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of enabling prediction of structures and properties of polymeric materials by computer-assisted experiments, studies were conducted for putting new simulation technologies to practical application. With the coarse-graining molecular dynamic method working group, a coarse-graining molecular dynamic engine high in generality and augmentability was developed so that an optimum coarse-graining model might be chosen and constructed to achieve any given purpose, and its installation was almost completed. The dynamic mean field method working group fabricated a new general-purpose simulator with its interface simplified and function improved. A simulation technique was also developed, which would be incorporated into the general-purpose simulator. The dispersed structure simulation working group developed a group of class libraries for use in continuum simulation. The platform working group, making use of Java excellent in general-purpose feature, worked out a function verification platform to run on Windows95/98/NT. (NEDO)

  20. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  1. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    Research, development and evaluation were performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the mechanism of light deterioration reaction of photochromic molecules, it was disclosed that 6-nitrospirobenzopyran has the light deterioration caused from the excitation triplet state. This disclosure presents a possibility of preventing the light deterioration. New derivatives that show photochromism were synthesized, and thin films were produced by using the LB process. This indicates a possibility of producing the photochromic materials as the high multiplex recording material. With regard to PHB materials, an evaluation technology having spectrum resolution of the world's highest level was established and measurements were performed. Hole formation was verified for the first time in the world at the temperature higher than the liquid nitrogen temperature by using a PHB material of ionic porphin/polyvinyl alcohol systems. This verification indicates a feasibility of practically usable PHB materials. (NEDO)

  2. Research and development of basic technologies for next generation industries, 'electrically conductive polymeric material'. Evaluation on first term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Dodensei kobunshi zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The research and development in the first term has searched widely different kinds of raw materials, elucidated electricity conduction mechanism, discussed processing technologies and evaluation methods. It also included molecule designing to develop new raw materials. A method for growing good single crystals of charge migrating complexes was developed, and (BEDT-TTF){sub 2}I{sub 3} crystals were found to manifest superconductivity at 8K under pressure of 1.3 kbar. In addition, elucidation was made on conduction characteristics of (TMTSF){sub 2}ClO{sub 4} being an induction superconductor, and on its superconduction mechanism. Polyacetylene films oriented at a high level by epitaxial polymerization were synthesized, the carrier hopping mechanism of polyacetylene was proposed, and the direction of increasing the conductivity was shown. It was discovered that cyanoacetylene is thermally polymerized at a relatively low temperature, turning into polymer with good orientation and easily into graphite. Polymeric intermediates soluble to polyparaphenylene vinylene (PPV) were synthesized, whereas these intermediates were found to have shaping and stretching properties, and conductivity of 2.8 times 10{sup 3}s/cm was obtained in PPV doped after the stretching. (NEDO)

  3. Research and development of the industrial basic technologies of the next generation, 'composite materials (resin-based)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (jushikei)'. Daiikki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-30

    The results of the first phase research and development project for developing the resin-based composite materials as the basic technologies of the next generation are evaluated. This project is aimed at development of the resin-based composite materials as light, high-strength and high-rigidity structural materials. Development of the basic techniques for these materials is of high significance, and highly rated. The first R and D phase efforts are directed to synthesis of new skeleton and terminal compounds, and their introduction into the matrices; application/combination of various fiber surface modification techniques; development of the basic techniques for intermediate materials for three-dimensional fabrics, triaxial fabrics and hybrid materials; improvement of the main techniques for a series of molding/processing steps; adoption of new methods; and development of design programs and elementary design techniques. The technical targets of improving functions of each item have been achieved, or bright prospects have been obtained therefor, each involving potentials of functional improvements by developing new functions. It is also considered that the parallel, competitive development and promotion of 7 routes in researches on the matrix resins have brought great effects. (NEDO)

  4. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly crystalline polymeric material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokesshosei kobunshi zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    Basic technologies are developed involving highly crystalline polymeric materials comparable to metals in dynamic property even when used singly. The aim is to expand the application scope of polymeric materials including those designed as structural materials so that their light weight, high resistance to corrosion, and excellent machinability may be utilized in various fields. Target performance includes an elastic modulus under bending force of 100GPa or more in anisotropic materials and 50GPa or more in isotropic materials, a linear expansion coefficient of 5 times 10{sup -5}/degrees C or less, and a thermal deformation temperature of 180 degrees C or more. Tasks faced in relation to film or molded articles of anisotropic materials are the rigid molecular design, molding method including molecular orientation control, and molecular complex technology; and, in isotropic materials, the strengthening of interaction between molecules, establishment of molding methods, and equipping materials with high machinability. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. To be mentioned are achievements involving the generation of multidimensionally bound diacetylene polymeric crystals, higher elastic modulus and moldability provided to polyarylate materials, magnetic field orientation, ultrahigh-elasticity layered body, and organic-inorganic ionically bonded complex material, etc. (NEDO)

  5. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly efficient polymeric separation membrane material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    For the enhancement of separation process efficiency and energy efficiency in the chemical industry, etc., basic technologies are developed involving high-performance separation membrane materials which are excellent in durability and usable in the field where separation by membranes has been impractical. The liquid mixtures subjected to separation are a neutral organic compound/water system, an acidic organic compound/water system, and a polar organic compound/water system; the gas mixtures subjected to separation are an oxygen/nitrogen system and a carbon monoxide/nitrogen system. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. Among those that have to be mentioned is the development of a nonaqueous separation membrane, a supported liquid membrane with amino acid optically active high performance separation capability, a high-precision evaluation unit for gas separation membrane characteristics, a selective permeation membrane with high-level oxygen and carbon monoxide carriers and reactivation technology, a high-performance ethanol separation membrane, a water/polar organic compound separation membrane, and a water/acetic acid separation membrane and stability providing technology. In particular, the water selective permeation membrane for a mixture of water and alcohol has already arrived at the stage of bench plant demonstration. (NEDO)

  6. Present situation, current problems and countermeasures to solve them by the material technology group in chemical companies; Kagaku shakai ni okeru sochi zairyo gijutsu no genjo to kadai oyobi sore eno taio

    Energy Technology Data Exchange (ETDEWEB)

    Nakahara, Masao. [Asahi Chemical Industry Corp., Tokyo (Japan). Production Technology Center

    1999-05-15

    A questionnaire investigation about the present situation, current problems and countermeasure to be discussed with by material technology groups in the eight chemical companies was carried out. It has become clear from the analysis of answers obtained that the roll of material group has been changing under the diminishing construction of new plant and the increased needs of stable and sustainable plant operation. The present major subjects of material groups, which are pointed out in the answers, are such new technological problems as the plant life estimation, the dissemination and handing down of material technology and the upbringing of technology successors. The countermeasures to meet those requirements made clear are such technology developments as a new monitoring system, preparation of database on material technology and closer cooperation with relatied associations. It is hoped for that the findings of this study would lead to further and more detailed indentification of common problems to be solved and development of practical countermeasures therefor. (author)

  7. Research and development of the industrial basic technologies of the next generation, 'composite materials (metal-based)'. Evaluation of the second phase research and development; Jisedai sdangyo kiban gijutsu kenkyu kaihatsu 'fukugo zairyo (kinzoukei)'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-31

    The results of the second phase research and development project for developing the metal-based composite materials as the basic technologies of the next generation are evaluated. For development of highly functional materials, the efforts are directed to modification of PAN-based high-strength carbon fibers for aluminum-based FRMs, and also to development of the methods for controlling interfacial reactions at high temperature by modification of the base materials for titanium-based FRMs. For development of carbon fiber-based intermediate materials, the techniques are developed for continuous production of wire preforms of aluminum. For development of molding/processing techniques, the press molding and powder HIP molding techniques are developed to give a planar product of the FRM of titanium alloy reinforced with evaporated filaments of silicon carbide, which shows an average tensile strength exceeding the target level. Also developed are the press and roll molding techniques for the wire preforms of aluminum reinforced with silicon carbide fibers, the planar product therefrom showing a tensile strength of at least 99% of the base material. It is concluded that the objectives of the second-phase project are almost achieved. (NEDO)

  8. FY 2000 report on the survey on energy conservation technology of large plant using ultra high corrosion resistant materials; 2000 nendo chokotaishokusei zairyo wo mochiita ogata plant no sho energy gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving remarkable energy conservation/resource conservation in large plants, the paper carried out an investigational survey of effects obtained in case of applying amorphous super metal which is the newest corrosion resistant material. Amorphous alloys as an ultra high corrosion resistant material are a peculiar material which shows the extremely excellent corrosion resistance even in much strong acid by containing passivated elements with the needed concentration. The corrosion resistant amorphous alloy applied to large plants need the thickness and diameter of more than several millimeters as a bulk material. The subjects are scaling-up of bulk materials and stabilization of characteristics. Even under the tough dew point corrosion environment of the waste power plant, etc., heat recovery from exhaust gas is made possible by heat exchanger applied with ultra high corrosion resistant materials. Effects of the annual heat recovery from the nationwide refuse incinerators and coal thermal power plants are estimated to be approximately 5.2 million kL toe, that is, to be equal to energy conservation of 6 x a million kW class power plant. (NEDO)

  9. Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

  10. Fiscal 1991-1993 summary report on R and D on new forming technology of composite materials; Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu 1991 nendo - 1993 nendo sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-09-01

    Developed were the materials which can be easily formed by manifesting superplasticity simultaneously with high toughness and high strength through selection of material composition and micronizing of the structure, in regard to composite materials answering to high strength and resistance to high temperature suitable for engines or the like. Developed for ceramic matrix composite materials were composite technology of silicon nitride matrix composites by a casting method, composite technology of Al{sub 2}O{sub 3}/TiC matrix composites by a material preparation method using aqueous slurry, and superplastic forming technology of yttria stabilized zirconia/alumina matrix composites; developed for metallic matrix composite materials were composite technology of reinforced ceramics particulate aluminum alloy matrix composites by a voltex method, composite technology of ceramic short fibers reinforced aluminum alloy composites by a high pressure casting method under reduced pressure, composite technology of titanium matrix composites by a mechanical alloying method, and composite technology of aluminum alloy composites by ceramics particles, superplastic forming technology of SiC whisker reinforced aluminum alloy reinforced composites, and superplastic forming technology of aluminum alloy matrix reinforced composites reinforced by SiC particles. (NEDO)

  11. Research and development project in fiscal 1989 for fundamental technologies for next generation industries. Achievement report on research and development on photoreactive materials (Research on designing and organizing technology for PHB materials); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. PHB zairyo no sekkei to soshikika gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective of putting into practical use the wavelength multiplex recording system applied with the PHB phenomenon, research and development has been performed on material systems making high quality hole production possible at high sensitivity and high density. This paper summarizes the achievements in fiscal 1989. In the discussion of PHB materials, measurements were performed on the triple state of zinc, magnesium, copper and iron complexes of tetra-phenyl porphin and the triple state spectra by using the flash decomposition method in order to develop new photo-gate type material systems. Correlation was discovered between the free energy change in the reaction and the PHB reactivity from the result of the experiments, whereas important findings were obtained for designing the photo-gate type PHB material systems. In the discussion of the wavelength multiplex recording, an optical system was designed and fabricated to perform scanning and detection on sample surface by using laser beam squeezed to a diameter of 100 {mu} m. Discussions were given on the wavelength multiplex recording, position multiplex recording, and high-speed recording using this optical system. As a result, position multiplex holes were produced successfully by using the laser beam squeezed to a diameter of 100 {mu} m on four different positions on the sample surface, when the tetra phenylporphin derivative was used. (NEDO)

  12. Report on surveys in fiscal 2000 on the surveys and researches on fundamental technology of polymeric materials in relation to materials nano-technology program; 2000 nendo zairyo nano technology program ni kansuru kobunshi zairyo kiban gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-11-01

    On the 'polymeric' technology field being the constitution elementary technology of the material neon-technology program, surveys and researches have been performed through holding workshops on the directionality of technological development to be proceeded in a medium term in the future, and the assignments to be worked on with emphasis. The 'Fundamental technology of polymeric materials workshop' was held together with the 49th polymer discussion meeting, in which 300 persons have attended showing high interest of researchers. With regard to the prospect and possibility of the polymeric technology, statements were given on the ways the polymeric technology development should be in the future, and expectations toward the polymeric technology. In the development assignments for the polymeric technology, discussions were given on the current status and problems in the primary structure control technology, tertiary structure control technology, and surface and interface structure control technology. Discussions were also given on the current status and problems in textiles as the high-order structure control technology, the current status and problems in the material forming technology, and the systematization of the polymeric technology and the knowledge thereof. The core of the polymeric technology is the nano-technology itself, whereas the expectations toward the 'Fundamental Polymeric Technology Research Center' were indicated. (NEDO)

  13. Report on surveys in fiscal 2000 on the surveys and researches on fundamental technology of polymeric materials in relation to materials nano-technology program; 2000 nendo zairyo nano technology program ni kansuru kobunshi zairyo kiban gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-11-01

    On the 'polymeric' technology field being the constitution elementary technology of the material neon-technology program, surveys and researches have been performed through holding workshops on the directionality of technological development to be proceeded in a medium term in the future, and the assignments to be worked on with emphasis. The 'Fundamental technology of polymeric materials workshop' was held together with the 49th polymer discussion meeting, in which 300 persons have attended showing high interest of researchers. With regard to the prospect and possibility of the polymeric technology, statements were given on the ways the polymeric technology development should be in the future, and expectations toward the polymeric technology. In the development assignments for the polymeric technology, discussions were given on the current status and problems in the primary structure control technology, tertiary structure control technology, and surface and interface structure control technology. Discussions were also given on the current status and problems in textiles as the high-order structure control technology, the current status and problems in the material forming technology, and the systematization of the polymeric technology and the knowledge thereof. The core of the polymeric technology is the nano-technology itself, whereas the expectations toward the 'Fundamental Polymeric Technology Research Center' were indicated. (NEDO)

  14. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system /development of technology to manufacture solar cells/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture silicon crystal based high-quality materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi seizo gijutsu kaihatsu, usumaku taiyo denchi seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (silicon kesshokei kohinshitsu zairyo kiban no seizo gujutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is intended to develop thin film solar cells capable of mass production with high photo-stability and at low cost. Thus, the objective of the present research is to analyze the growth process of micro crystal silicon based thin films, the crystal being a high quality silicon crystal based material, and develop technology to manufacture high-quality micro crystal silicon thin films based on the findings therefrom. It was found that, when silicon source is available in cathode, pure hydrogen plasma forms micro crystal silicon films by using the plasma as a result of the chemical transportation effect from the silicon source. It was revealed that the crystal formation due to hydrogen plasma exposure is performed substantially by the crystals forming the films due to the chemical transportation effect, rather than crystallization in the vicinity of the surface. The crystal formation under this experiment was concluded that the formation takes place during film growth accompanied by diffusion of film forming precursors on the surface on which the film grows. According to the result obtained so far, the most important issue in the future is particularly the control of crystal growing azimuth by reducing the initially formed amorphous layer by controlling the stress in the initial phase for film formation, and by controlling the film forming precursors. (NEDO)

  15. Achievement report for fiscal 1997 on development of practical application technology for photovoltaic power generation systems. Development of technologies to manufacture thin film solar cells (development of technologies to manufacture silicon crystal based high-quality materials and substrates / survey and research on analysis of practical application); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu / silicon kesshokei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As a plan to develop technologies to manufacture materials and substrates for thin film solar cells, it is intended to reduce defect density, enhance film forming speed, largely improve the photo-electric conversion efficiency and increase manufacturing productivity. These goals will be realized by establishing methods to control defect density, crystal particle diameters and crystallization rate in silicon crystal systems. A technology to form micro-crystal silicon-based thin films will be developed, that have superior photo-stability, and are capable of realizing low cost and mass production. Discussions will be given on a high-density plasma control technology, a fundamental property evaluation technology for micro crystal silicon thin films, and a device design simulation technology. A technology will be developed to form amorphous silicon layer on a stainless steel substrate by using the plasma CVD process. At the same time, discussions will be given on optical annealing and thermal annealing as reformation methods. Fiscal 1997 has surveyed component technologies to identify and analyze quickly and accurately the technical trends inside and outside the country, and to mass produce thin film solar cells. The Material and Substrate System Technology Subcommittee (silicon crystals) was held to deliberate the four-year development program and its progress. (NEDO)

  16. FY 1999 New Sunshine Project survey research project - Survey on the long-term energy technology strategy, etc. Fundamental survey to decide on the industrial technology strategy - Technology strategy by field (Material technology field - Nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey/study were conducted to contribute to proposing technology strategies such as technical competitive force and the forecast in the material field, especially in the silicon wafer and compound semiconductor field. As to the silicon wafer technology, the following technologies were pointed out as those to be reinforced: future silicon crystals, mirror processing wafer, breakthrough technology needed for super LSI, heat-treated wafer, epitaxial wafer, SOI wafer, measuring/assessment technology, etc. In relation to the compound semiconductor technology, survey/study were made on the bulk crystal growth technology, epitaxial growth technology, crystal growth device technology, wafer processing technology, inspection/evaluation technology, device processing technology, etc. As the comprehensive strategy, the following were proposed: establishment of the place for industry/government/university cooperation, establishment of the center for evaluation of wafer materials/characteristics/process, and establishment of the compound semiconductor R and D center where men of practical business ability from industry/government/university get together and conduct the R and D of production technology and production facilities for compound semiconductor materials and devices. (NEDO)

  17. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium on energy research in its 3rd year (Development of nano-structured materials for ceramic bearing applications); 1999 nendo ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu seika hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Coprecipitation in a chloride-containing water solution is utilized to deposit zirconia nano-particles on alumina particles for the manufacture of a composite powder and a sintered body. As compared with a conventional CIP (cold isostatic press)-molded compact, a slip-cast compact is improved in flexural strength from 1.1 to 1.36Gpa. A composite powder granulating unit is installed. Although it is known that use of the citric acid as gelatinizer in the coprecipitation process results in a homogenous ZrO{sub 2}-Al{sub 2}O{sub 3} composite powder, yet a method is contrived to achieve high crystallinity without gelatinizer by freezing and drying a chloride-containing water solution in a microgravity field. In the near-net molding of spherical ceramic particles, an error in diameter of not more than 50{mu}m is realized. A mass production technology is established by which an inexpensive general-purpose alumina nano-structured material is die-compacted for the manufacture of low-cost ceramic bearings. A high-speed super-flat spherical surface processing technology is developed. In a 25kg-load fatigue test conducted for a combination of nano-structured ceramic balls and steel flat plates that bear the balls, a 240-hour life is attained. The bearing steel stands comparison with those available on the market. (NEDO)

  18. Achievement report on research and development in fiscal 1989 for fundamental technologies for next generation industries. Research and development on photoreactive materials (Research on control of association status of photochromic compounds); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Photochromic kagobutsu no kaigo jotai seigyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective of creating ultra-high density organic photo recording elements for photon mode recording and rewritable wavelength multiplex recording by utilizing control of association status of photochromic compound, research and development has been performed. This paper summarizes the achievements in fiscal 1989. In developing the materials, verification was made on effectiveness of the newly structured positive polarity model. The method was used to attempt synthesis of four kinds of new spiropyrane, among which it was discovered that BSP1822 forms J-association complex in the long wavelength region. In the thin film forming technology, the J-association complex of BSP1822 was stabilized successfully in the film mixed with bi-molecular film forming material. In order to develop a technology to form dry photochromic thin films, an organic molecular beam epitaxial device and a thin film structure analyzer were introduced. In the elucidation and research on fundamental properties, discussions were given on properties of the SP1822LB film revealed by the steady-state light and laser pulse light. Furthermore, the molecular orientation of the SP1801 on the air-water interface was investigated, and molecular models on the air-water interface were considered. (NEDO)

  19. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium on energy research in its 3rd year (Research and development of mezoscopic composite phase material based on heat-/wear-resistant metal); 1999 nendo mezoscopic fukuso soshiki seigyo tainetsu taimamosei kinzokuki fukugo zairyo no kenkyu kaihatsu seika hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Using an in-situ method, three kinds of Fe-C-Ni-Cr-Mo-Nb-based alloys are developed, whose strength is not less than 800MPa at 1073K. They exhibit, in a high-temperature erosion wear test, a wear resistance which is 2-3 times higher than that of conventional materials. When they are cast, wear-causing graphite precipitation is suppressed thanks to the cast iron coagulating in gaps in the ceramic formed into a net shape. It is also found that in this process the precipitation of cementites etc., which improves on the abrasion and wear characteristics, is accelerated and that the cementites etc. are finely dispersed for improvement on the brake (brake block) characteristics. Tentatively produced brake blocks are tested for performance at the Railway Technical Research Institute. The new materials are found to exhibit a wear resistance which is 2.2 times higher, and a braking capability 1.6 times better, than those of conventional materials. In the case of an Fe-50Cr-4.8C alloy produced by an MA (mechanical alloying) method, {alpha}-Fe is dispersed into M{sub 23}C{sub 6} for a remarkable improvement on the wear-resisting feature. A 10%TiC cermet exhibits a remarkably high wear resistance, that is, a transverse rupture strength of 1270MPa which is higher than that of a cast high-speed steel. (NEDO)

  20. Study on the improvement of high temperature mechanical properties of carbon fiber reinforced ceramics composites through texture and interface controls; Tanso sen`i kyoka ceramics fukugo zairyo no soshiki kaimen seigyo ni yoru koon rikigaku tokusei kaizen ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To improve the tenacity and reliability of ceramics, the fiber reinforced ceramics composites compounding high strength long fibers and ceramics have been investigated. In this study, carbon fibers were selected as reinforcement fibers. The hexagonal boron nitride (hBN) was selected as a matrix having the plastic deformation performance. To intend to control the composition of the fiber/matrix interface, composites were created by adding polysilazane which was an organic Si (Si3N4) source. Relationships between the condition of interface of each phase and the high temperature mechanical properties were examined by changing the fabrication condition, to grasp the technical problems, such as the optimization of fabrication condition. Knowledge on the fabrication of long fiber reinforced ceramics composites was obtained including the arbitrary control technology of interface consistency of ceramics composites for super high temperature structures. The carbon fiber reinforced hBN composites developed in this study have excellent strength up to 1,500 centigrade and fracture energy, and they are new prospective materials as well as C/C composites. 4 refs., 37 figs., 13 tabs.

  1. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / development of nano-structured materials for ceramic bearing application (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing high efficient ceramic bearing using nano-structured materials, technical development was proceeded with of raw material powder treatment, forming sintering, processing, structural analysis, property evaluation, etc. As to the study of manufacturing of ceramic balls, the following were conducted by the method developed at Osaka Prefectural Institute of Industrial Technology: coprecipitation laminate processing of ZrO2-Al2O3 system to alumina powder at Okumura Crucible Mfg. Co. Ltd., spherial press processing and sintering at Kyocera Co. Ltd., and precise machining at Nippon Pillow Block Mfg., Co. Ltd. The performance as bearing was measured of the ceramic balls obtained such as surface coarseness, sphericity, crush strength and fatigue life. Surface coarseness and sphericity were the same as those of bearing use silicon nitride, but crush strength was considerably low. In the experiment on rolling fatigue strength as bearing, separation occurred within 100 hours even at a load of 100kgf. It is thought that this is because of the pores remaining on the surface, and the measures to be taken for long life were studied. 12 refs., 64 figs., 27 tabs.

  2. Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

  3. Report on achievements in fiscal 1999 on research and development of the glycocluster controlled biological molecule synthesizing under the industrial and scientific technology research and development theme [university collaborated type]. Bio-fiber manufacturing technology of glycocluster utilizing type; 1999 nendo glycocluster seigyo seitai bunshi gosei gijutsu seika hokokusho (glycocluster riyogata bio sen'i seizo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1999 on development of the technology to manufacture glycocluster controlled biological molecules, particularly bio-fibers. It was made clear for the first time that the method for synthesizing glycoside and sugar chain using solid ultra-strong acid can be a new method for polysaccharide synthesis (polycondensation reaction) which is extremely simple and versatile as a result of using the solid ultra-strong acid. It can also be applied to general glycoside synthesis. In glycopeptide synthesis of the regular sequence type using high-functional condensation reaction, such a condensation agent as diphenyl phosphoryl azide was found effective in polymerization reaction without protection of glycopeptide, which has been impossible conventionally, and was found to have high versatility as a method for synthesizing mucin glycoproteins widely distributed naturally. In simplified synthesis of physiologically active glycopeptide, notice was given to tyrosine which is not glycosylated in the natural world, even though having hydroxyl groups in side chains as in serine and threonine. A method was established to introduce sugar chains into this hydroxyl group. This method exhibits power also in the synthesis of physiologically active glycopeptide of non-natural type. The paper describes also the comprehensive survey. (NEDO)

  4. Fiscal 2000 achievement report on the important regional technology research and development. Research and development of eco-tailored tribo-material creation process technology (Research and development of nanometer-order controlled material creation process technology); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Eco tailored tribo material sosei process gijutsu no kenkyu kaihatsu (nanometer order de seigyo sareta material sosei process gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop tribo-material creation process technologies capable of meeting the needs of environmental protection and energy conservation relative to automobile engine parts such as piston rings, cams, shims, and the like. Activities are conducted in the three fields of (1) the research and development of nanostructure material creation technologies, (2) research and development of tribological evaluation technologies, and (3) the verification of the developed technologies. In field (1), a nanostructure control process is studied, and tribo-composite materials are examined. In field (1), in fiscal 2000, the arc ion plating method is selected as a nanostructure control process, and the closed type nonequilibrium magnetron sputtering method as the base for development into a process. As for tribo-composite materials, Ti-Si-N based and Cr-Si-N based coatings find their feasibility in shims, and Cr-Si-N based and Cr-Si-C-N based coatings in piston rings. Compiled in this report are the summary, and the studies of nanostructure control process technologies, joint studies, composite ceramic coating practicalization technologies, and technologies for putting to practical use coatings which comprise layers of different substances. (NEDO)

  5. Fiscal 1999 report on results of R and D of industrial science and technology that creates new industry. Development of super metal technology (development of technology for innovative metallic material); 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of obtaining higher strength/toughness and higher anticorrosion in metallic materials, R and D was conducted on technologies for grain refining/dispersing and for amorphous bulk formed bodies, with fiscal 1999 results compiled. In the technological study on grain refinement and dispersion, austenitic stainless steel and 12Cr ferrite steel were used, with creative manufacturing carried out for microcrystallized structure materials by a powder metallurgy method. The result of the study revealed that suppressing grain growth by carbide or oxide was important for grain refinement, and that homogenizing the inside of a material by hot forging after solidification forming was essential for ductility improvement. In the development of the technology for amorphous bulk formed bodies, a laser heating type forming test device was designed and manufactured, with a technique examined in which bulk amorphous of a complex-shaped article was formed through rapid quenching of amorphous alloy powder by laser. This year, a trial production was performed for the laminated solidified bodies of Ni amorphous alloy powder, and the basic data was thereby collected such as feeding of the powder and conditions of the laser irradiation. (NEDO)

  6. FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 6. Development of cryogenic temperature materials technologies; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 6 (teion zairyo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Summarized herein are the cryogenic temperature materials technologies for the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project, developed in FY 1998. The R and D programs have been implemented continuously since 1994. For stainless steel, the base and TIG weld metals were evaluated for their material characteristics in liquid hydrogen. The items investigated included the influences of hydrogen charge, 20% of stretch working on the base metal, welding methods, and ?-ferrite content on the characteristics. Fatigue strength of the base metal was found to increases as temperature decreases, but remain unchanged in a range from 20 to 77K. No significant difference was observed between 304L and 316L. For aluminum alloy, mechanical characteristics, centered by fatigue characteristics, were investigated for the base and weld metals. The sample of higher tensile strength showed a higher fatigue strength, at room temperature, 77 and 4K. The other tested items investigated included embrittlement characteristics in a hydrogen atmosphere, phase transformation, hydrogen diffusion and fracture toughness, for establishing the databases of cryogenic temperature materials. (NEDO)

  7. `Joint Research and Development of Industrial Technology,` an international research collaboration for fiscal 1997. Research and development for practical application of low-temperature sinterable, highly heat-radiating materials for ceramics; 1997 nendo kokusai kenkyu kyoryoku jigyo `sangyo kiban gijutsu kyodo kenkyu kaihatsu`. Teion shoketsu kohonetsusei ceramics kiban zairyo no jitsuyoka gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A highly heat-conducting AlN ceramic substrate is developed for the cooling of semiconductor integrated circuit devices and power controlling semiconductor devices. In the development of a low-temperature sinterable ceramic texture, a sintering assistant is selected. In this process various assistants are tested for the effect of their presence on the occurrence of AlN oxidation and on the magnitude of standard energy for aluminate compound formation. The volatility at high temperatures of the components of the assistants are also examined. The sintering assistant developed for this project (mixture of Y2O3, CaO, LaB6, and WO3) is used in the sintering of an AlN material powder developed by The Dow Chemical Co., and then it is demonstrated that highly heat-conducting AlN substrates are mass-produced by continuous sintering at 1600degC in a nitrogen atmosphere, the product having a relative density of 100%, average heat conductivity of 154W/mK, bend resisting strength of 440MPa, and a fracture toughness value of 3.8MPam{sup 1/2}. 6 refs., 92 figs., 10 tabs.

  8. Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

  9. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

  10. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

  11. FY 1998 report on the results of the R and D of industrial science technology. R and D of 'carbon-base high functional material technology' (R and D of the submarine oil production support system); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu (kaitei sekiyu seisan shien system kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    For the R and D of carbon-base high functional materials, the paper reported on (1) material creation technology and (2) creation of mechanically high functional materials. In (1), the synthesis of new BCN-base materials is conducted by the electronic excitation CVD method and high temperature/high pressure (explosive synthesis) with the aim of analyzing the composition/structure. Using energy-controlled ion beams and laser beams, the synthesis of new CN-base materials and analysis of composition/structure are aimed at. By the thermal CVD method using catalysts, a method to synthesize a quantity of nanotubes is aimed at. The paper is aimed at clarifying the reaction mechanism on the material conversion of carbonaceous materials relating to the above-mentioned three methods and the appearance mechanism of characteristics of carbonaceous materials. (2) is composed of the following three subjects: composition gradient film formation technology, complicated shape film formation/micro-processing technology, and large area film formation. These three subjects were studied to positively make use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected in amorphous carbon, diamond and high functional carbon materials of carbon nitride and to apply them to moving parts of various industrial machines and surface protection of construction materials such as glass, etc. (NEDO)

  12. Fiscal 1993 report on technological results. R and D on new forming technology of composite materials (Development of innovative technology for producing members for high efficiency power generation); 1993 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    A forming technology was developed which uses superplasticity of composite materials, i.e., high-functional materials for power generating equipment for example. Activities were conducted in the three areas of (1) ceramic based composite materials, (2) development of metal-based composite forming technology, and (3) comprehensive investigation and adjustment. In (1), with a view to finding a composite forming technology, in which high tenacity materials are obtained by evenly dispersing particles or whiskers as reinforcements in a matrix, a room temperature forming technique using fine particles was exploited, as were a high temperature forming technique using fused bodies and a possibility of manifestation of superplasticity in the prepared composite materials. The materials used were Si{sub 3}N{sub 4} matrix-SiC, Al{sub 2}O{sub 3} matrix-TiC, and glass matrix composite based materials filling ceramics in fine holes of porous glass. In (2), composite forming technologies were examined for such composite materials as Al alloy matrix-SiC particulate-based by a molten metal stirring method, Al alloy matrix-ceramics short fiber-based by a high pressure forging method, Ti alloy matrix-ceramics particulate-based by a mechanical alloying method, and Al alloy matrix-ceramics particulate-based by an alkoxide method/powder metallurgy method. (NEDO)

  13. FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the technology to rationalize energy utilization; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the FY 2000 results. In Chapter 1, development of electrically high functional diamond process technology, electric characteristics which frontier carbon materials have were made clear by the following four subjects, and the development was executed of original production process technology for realizing energy saving by heightening efficiency of electric devices, displays, etc. 1) development of morphology control; 2) development of technology to control electron emission characteristics; 3) development of technology to control oriented growth; 4) development of technology to enlarge single crystals. In Chapter 2, the basement technology of electron emission control was studied. Namely, conditions for film formation were investigated to elucidate the formation mechanism of carbon nano structure films by Dual RF CVD method, IPC CVD method and thermal CVD method. As to the electron emission mechanism of diamond, electron emission characteristics were outlined of the boron dope diamond thin film formed by micro wave plasma CVD method in FY 1999. In Chapter 3, investigational study of original production process technology of electrically high function materials, test study was made of the element technology needed to make high quality/large area diamond substrates. (NEDO)

  14. Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of technology for rationalizing use of energy); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    R and D was conducted on original processing technology for electrically functional materials as a R and D project on frontier carbon technology, with the results for fiscal 1999 compiled. In the development of film forming technology using a large morphology control film forming device, the device was introduced this year, with film forming conditions probed. In the development of large size diamond synthesis process, single crystal synthesis and evaluation were carried out using an existing microwave plasma CVD reactor, with a study of design made for the device for obtaining a target 16 mm diameter single crystal. In the development of technology for oriented diamond growth on a platinum-based metallic base plate, research was done for controlling generation of grain boundary in a diamond film, through the improvement of orientation and the reduction of non-oriented grain density of the diamond nucleated on the base plate. The studies on control technology of surface-interface and electron emission characteristics were conducted on such subjects as fabrication technology of diamond for field emission, characterization of field emission, and photoelectron emission spectroscopy of diamond. (NEDO)

  15. Fiscal 2000 technology trend survey. Survey of technology trend relating to next-generation metal-based material compatible with inverse manufacturing leading to energy use rationalization; 2000 nendo gijutsu doko chosa hokokusho. Energy shiyo gorika ni kakawaru inverse manufacturing ni tekigoushita jisedai kinzoku kei zairyo ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the construction of a recycling system consuming less energy and therefore higher in efficiency, studies were made about the feasibility of metallic material developing/recycling systems more congruent with the objective through the application of inverse manufacturing (IM). Concerning metallic materials and recycling technologies, steel, aluminum alloys, and magnesium alloys were taken up, and a survey was made of hazardous elements in steel materials, unification of materials to constitute aluminum alloy parts, yield of magnesium in die casting, and the like. In the survey of recycling of automobiles, it was pointed out that the treatment of resin-based shredder dust was posing problems and that the use of metallic materials high in recyclability was essential to IM. In conclusion, three propositions were presented, which involved technologies for the advanced use of magnesium alloys as materials leading to the realization of IM, the development of recycling-oriented general-purpose alloys (with Mg and Al as mother metals), and the development of functional bonding technology enabling debonding (debondable bonding technology). (NEDO)

  16. Fiscal 1994 report on results of R and D on innovative technology for producing advanced biomaterial. Technology of fixation and utilization of carbon dioxide using peptides; 1994 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. Pepuchido oyo nisanka tanso koteika yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    R and D of a material was conducted that has a function of fixation of carbon dioxide for example, by synthesizing non-natural amino acids required for the manifestation of the function, incorporating the amino acids into new bio-functional peptides to be synthesized, and fixing the peptides on a substrate. Activities were carried out in three areas, which were (1) innovative technologies for producing functional molecules: R and D concerning structural and functional design of peptides, conformational control technique, preparation of peptides with photoelectric conversion function, peptide synthesis using enzyme, and method of incorporating non-natural amino acids into peptides, (2) R and D on materialization technologies of functional molecules: formation of film onto a substrate, pattern forming technique, substrate modification technique, peptide binding reagent or linker, and development of technologies for creation of biomaterials having molecular recognition function and their stabilization. and (3) comprehensive investigation and adjustment (operation of information exchange conference and adjustment of the progress). In (2), an examination was made on the effect of polymerization on functions, for example, by fixing molecular recognition peptides in monomers and polymers on a catalyst support. (NEDO)

  17. Report on achievements in fiscal 1998. Venture business growing type consortium - small business creating infrastructure (Research on polychloride vinyl resin substituting technology applying technology to reform surface of polymeric materials); 1998 nendo kobunshi zairyo no hyomen kaishitsu gijutsu wo oyoshita pori enka biniru jushi daitaika gijutsu ni kansuru kebnky seika hokokusho.

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is intended to develop a technology to substitute polyvinyl chloride resin being regarded as the generation source of dioxines and environmental hormones in spite of being low in cost and having many excellent characteristics, with polyolefin resin having the same mechanical properties. It has become possible to improve adhesion of polyolefin, and substitute the products manufactured by using polyvinyl chloride resin currently with the polyolefin resin having about the same mechanical properties by establishing the technology to form two layers of polyolefin resin and modified polyolefin resin having polar groups, and by developing a bonding pretreatment agent using soft polyolefin resin as the base. The developed technology can be applied to developing products as targeted by the business entities participating in this project (the edge material for bath tub lids, a product currently available, and the water draining pipe as a new product). The current fiscal year has executed the following activities: (1) improvement in high-frequency weldability by means of polymer blending, (2) development of primers, (3) development of a two-layer forming technology to laminate resin layers with excellent adhesion on material surface, and (4) development of the plasma treatment technology. (NEDO)

  18. Fiscal 2000 report on results of R and D of industrial science and technology that creates new industry. Development of supermetal technology (development of technology for innovative metallic material); 2000 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of obtaining higher strength/toughness in metallic materials, R and D was conducted concerning nano-sized grain refining and bulk forming by micro-grain dispersion, with fiscal 2000 results compiled. In {gamma} stainless steel, development was conducted using SUS304 as the base material, revealing that ZrC was effective for forming a micro-crystallized grain structure. In addition, it was found feasible that precipitation behavior of carbide was controllable through a temperature rising process at the time of solidification forming. In an HIP+ (hot isostatic pressing) hot forged material with ZrC finely dispersed, it characteristically showed an average crystalline grain size of about 300 nm, a tensile strength of 1,085 MPa, and a Charpy impact value of 1.86 MJ/m{sup 2}. Further, in thin plates micro-crystallized by thermo-mechanical treatment using martensite reverse transformation, a strain rate sensitivity index m value became 0.3 or higher at a strain rate of 10{sup -2}S{sup -1}, indicating manifestation of superplasticity. In {sigma} stainless steel, TiO{sub 2} and ZrO{sub 2} were examined for their effect of suppressing grain growth on the basis of SUS410. (NEDO)

  19. Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial. Peptide applied carbon dioxide fixation/effective utilization technology (First volume); 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. 1. Peptide oyo nisanka tanso koteika yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Technology is being developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation is introduced, and by modifying the surface of a base plate such as silica glass by using such peptides. Activities were conducted in the three areas of (1) creation of functional molecules, (2) materialization technology, and (3) comprehensive investigation and research; the activities were carried out independently and parallelly in the first two areas. In (1), design technique for the structures and functions of peptides was developed, as were conformational control technique, synthesis of peptides having optical/electronic functions, peptide synthesis by an enzyme method, and R and D on introduction of non-natural amino acid into peptides; in (2), element technologies were developed such as substrate forming technique (pattern forming and thin film forming technology), substrate modification technique, development of reagent for binding peptide onto a substrate, and R and D on creation of biomaterials having molecular recognition function and its stabilization technique. In (3), progress control in promoting themes and a meeting for exchanging information were conducted, while survey on related element technologies was systematically and comprehensively carried out. (NEDO)

  20. Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial. Peptide applied carbon dioxide fixation/effective utilization technology (Second volume: comprehensive investigation and research); 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho (sogo chosa kenkyu). 2. Peptide oyo nisanka tanso koteika yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Technology was developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation was introduced, and by fixing the peptides to the surface of a base plate such as silica glass or modifying the surface with them. As the related technological investigation, the following six areas were surveyed. (1) Structural design of peptides, (2) synthesis of peptides by chemical and enzyme methods, (3) synthesis of non-natural amino acid and its introduction into peptides, (4) structural analysis of peptides, (5) physiological activity of peptides, and (6) materialization and functional manifestation of peptides. With the exception of the area (5) consisting of one advanced research case, other areas were constituted of analysis, general remarks and research cases. The area (6) was constituted of materialization technique 1 and 2, film function and peptide, catalytic action 1 and 2, and one research case; the materialization technique was defined as a technique for modifying the surface of a synthetic resin, metallic or silica glass substrate with functional peptides; and an explanation was given to the present state of the fixation, pattern formation and integration technologies. (NEDO)

  1. FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-performance materials technology (R and D for rationalization of energy consumption); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This report summarizes the FY 1998 research and development results of carbon-based high-performance materials technology. For (control technology of morphology and electrical conduction), a large-sized morphology controlling film-making apparatus was used, to confirm synthesis of crystalline diamond films. For research on growth of large-sized single-crystal diamond, the simulated results of the vapor-phase reactions and gas flow in a plasma were compared with the observed ones, to collect the data necessary for designing a high-speed homoepitaxial growth apparatus. For R and D of heteroepitaxial growth of thin diamond films, highly single-crystalline thin platinum films were successfully formed on a sapphire substrate. For (control technology of surface-interface and electron emission characteristics), the tests were conducted using newly introduced apparatuses, an (electron emission analysis/evaluation apparatus), (high-quality carbon-based thin film synthesizing apparatus) and (element processing/treatment apparatus). It is found that electron emission efficiency is greatly improved when the substrate with diamond particle seeds is plasma-treated under specific conditions. (NEDO)

  2. Fiscal 1997 survey report. Subtask 6 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of technology of low temperature materials); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 6 teion zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the results of the development of technology of low temperature materials in the fiscal 1997 WE-NET. Using experimental equipment for materials under the atmosphere of liquid hydrogen, an experiment on mechanical characteristics under the liquid hydrogen atmosphere (20K) was conducted of the base materials of candidate steels (SUS304L, SUS316L and A5083). In material evaluation experiments (tension/fracture toughness/fracture tests), characteristic behaviors of the materials were shown which are different from those shown in the environment of liquid He (4k), etc. Even if the amount of {delta} ferrite in the metal welded of the stainless steel is small, approximately 1%, the degradation of low temperature toughness occurred. Welded joints of stainless steel by submerged arc welding and MAG welding were in now way inferior in tension characteristic to those by TIG welding, but were inferior in toughness ranging from room temperature to extremely low temperature. As to aluminum alloys, materials excellent in extremely-low temperature toughness were able to be found. Under the low temperature hydrogen gas atmosphere, the lower the strain rate is, the higher the hydrogen brittleness susceptibility is around 220K (extremely large hydrogen brittleness temperature) (SUS304L). In the hydrogen gas of 100 atm, hydrogen invades the material at 100degC, but does not at 77k. 38 refs., 173 figs., 48 tabs.

  3. FY 1992 Report on results of the research and development of the technologies for forming composite materials. Development of the technologies for creating parts for high-efficiency power generation systems; 1992 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the technologies for producing ceramic- and metal-based composite materials, and also technologies for superplastic processing by utilizing the phenomenon of superplasticity. The methods studied for development of the ceramic-based composites include casting and powder-utilizing forming at low temperature, and melt forming at high temperature. Those for the metal-based composites include melting at normal and high pressure, powder metallurgy type mechanical alloying and alkoxide methods. The composites studied for development of the superplastic processing are the whisker- and particle-reinforced ones. The composite reinforced with silicon nitride/SiC whiskers is found to be electrophoretically cast to have a bending strength of 497MPa at 1,250 degrees C. The parts of simple shape, e.g., rod and disk, having the target strength are produced by isostatically pressing at normal temperature and high pressure (CIP) and subsequently firing the granules, produced by spray drying the TiC particle/alumina-based slurry. (NEDO)

  4. Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

  5. Fiscal 1994 report on results of R and D on new forming technology of composite materials. Development of innovative technology for producing members for high efficiency power generation; 1994 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Activities were conducted in the three areas of (1) R and D on ceramic matrix composite forming technology, (2) R and D on metallic matrix composite forming technology, and (3) comprehensive investigation and adjustment, for the purpose of developing materials that manifest superplasticity among ceramic and metallic matrix composites as well as developing the forming and fabrication technology and also of improving productivity by simplifying the fabrication processes. In (1), upon discovering that the superplastic properties of zirconia (3Y-ZrO{sub 2}) sold in the market is affected by the grain size and impurities (Al{sub 2}O{sub 3}) of the material, a zirconia was developed in which a trace of Al{sub 2}O{sub 3} and SiO{sub 2} were added, with a method detected capable of the fabrication through a low deforming stress. In (2), development was carried forward for a new high specific strength high-temperature material applicable to aircraft engines for example, as well as its forming and fabrication technology, by making a composite between metals and between metal and ceramics by a mechanical alloying (MA) method. Metalcarbide, nitride and oxide made by the MA method were sintered by hot press or the like, and a sintered material was thereby obtained that was superplastic and capable of the near net-shape forming. (NEDO)

  6. 1998 report on results of research and development on new venture type industrial science and technology. 'Technological development of super metal' (technological development of innovative metallic material); 1998 nendo super metal no gijutsu kaihatsu seika hokokusho. Kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Results on 1998 research and development were summarized concerning the technological development of innovative metallic materials. In the research of particulate micro-diffusion technology, as a modeling of nano-structure holding process, Ag/Fe nano-crystal alloy was manufactured by inert gas vapor deposition, with the structural change at the time of rolling examined. In addition, a large-scale spark plasma sintering device was developed, with a 40mm diameter cylinder manufactured. In the research on crystal grain refining process by a stirring solidification method, crystal grain refining was achieved to 1{mu}m order. In the development of an advanced aluminum alloy forming method, concerning a high-speed superplastic molding technology, a basic evaluation test was carried out for the superplastic characteristics of rapidly solidified aluminum alloy continuously from fiscal 1997. Further, a calculator simulation was performed by the finite element method for the high-speed superplastic molding. From these results, knowledge was obtained necessary for the detailed design of a high-speed superplastic molding device. On the basis of this knowledge, manufacturing of the equipment was implemented, as were the introduction, rise, basic test, etc. (NEDO)

  7. Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

  8. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the synthesis and processing of advanced biomaterials (fixation and effective utilization of carbon dioxide using peptides); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (peptide oyo nisanka tanso koteika yuko riyo gijutsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In fiscal 1997, study was made on formation of peptides with a biogenic function and molecular recognition function, and peptide materials. The existing automatic design technique of peptides including non-natural amino acids was applied to design of complementary peptides of proteins with known structures to optimize a development technique of ligand. Practical function of peptides as advanced receptor ligand was verified by applying the existing conformation control technique to stable holding of peptide active conformation. Creation of bio-materials, and development of preparation technology of bio-substrates and materializing technology of functional molecular materials were carried out. To construct an electron transfer system by self- organized body of peptides formed on a substrate, a peptide molecular device was prepared and verified using linkers. To use peptides as photoelectron functional molecule, metallized peptide with main helix structure was prepared. The possibility of molecular materials with a fixation function of CO2 was examined. A high-sensitivity bio-sensor was also mentioned. 75 refs., 130 figs., 25 tabs.

  9. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

  10. FY 1999 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (R and D of the intellectual material and structural systems); 1999 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (chiteki zairyo kozo system no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 1999 results of the R and D project for development of intellectual materials and structural systems, where the fibrous or leafy sensor material or element (muscle) is integrated with a structure of an advanced material (skeleton) to process and control information (brain). The program for development of the health monitoring technologies develops the fine optical fiber (diameter: 40{mu}m), which is on a level with the conventional 125{mu}m-diameter fiber in strength and fatigue characteristics, for the high-performance sensor systems. The self-diagnosis of soundness, e.g., detection of impact loads and damages, is attempted using the fine optical fibers embedded in the composite structures. The program for active-adaptive control of smart structures investigates control of vibration and noise for beam structure elements, using the theoretical model developed for shape memory alloys. The vibration tests are conducted, where a distribution type sensor is used for active-adaptive control of soft structures, and the good results are produced. The program for development of actuator materials and elements produces high-strength, high-toughness PZT and PNN-PZT sheets of uniformly distributed thickness by the doctor blade method. (NEDO).

  11. Achievement report for fiscal 1999 on development of 'technology to promote reduction of discharge of dioxins and development of technology to suppress discharge of dioxins in aluminum product manufacturing processes'; 1999 nendo dioxine rui haishutsu sakugen sokushin gijutsu kaihatsu seika hokokusho. Aluminium seihin seizo kotei ni okeru dioxin rui no haishutsu yokusei seigyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been performed with an objective to reduce discharge of dioxins in aluminum product manufacturing processes. With regard to the quantity of chlorine used in aluminum molten metal refining process, the refining tests using 100% chlorine gas and the mixed gas (nitrogen gas mixed at 80%) revealed that either gas has approximately the same degassing performance, and the use of the mixed gas can reduce the amount of chlorine used. Dioxin concentrations in the gas discharged from the refining process were measured under the refining condition using less amount of chlorine. As a result, it was verified that, in the case of using 20% chlorine gas plus 80% nitrogen gas, the concentrations of dioxins decrease to about l/6, or 0.6 ng-TEQ/N{sup 3}. The studies on suppressing the discharge of dioxins from the facility to wash chlorine treatment exhaust gas discovered that dioxin concentration in the scrubber circulating solution can be suppressed to 1/10 or less by means of gravity precipitation and separation of the suspended liquid. It was also made clear that pH should preferably be controlled to 10.5 to separate suspended substances from the precipitated solution. (NEDO)

  12. FY 1999 Industrial science and technology research and development project. Report on the results of research and development of the technologies for genome informatics (Acceleration of analysis of green mold transcription control information); 1999 nendo genome infomatics gijutsu kenkyu kaihatsu seika hokokusho. Koji kabi no tensha seigyo joho no kaiseki kasokuka nado

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A total of 49 budding yeast transcription factor disruptants and one conditional transcription over expression strain are produced, to elucidate the gene regulation networks using the gene expression profile data, and to measure the systematic and high-quality gene expression profiles using the Affymetrix's GeneChip system. The program is also developed for accurately predicting the base sequences which regulate expression of given gene groups, based on the uniqueness of the upstream sequences. The analysis with the aid of the program predicts 8 gene expression regulation sequences, which are considered to be novel, from the gene groups of retarded expression by the transcription factor disruptants. The time course gene expression data are produced from the transcription factor SW14 conditional over expression strain. The analysis of the data indicates that the analysis of the subtracted genes using the gene expression profiles from the wild type strain is useful for clarifying the effects of the derived transcription factor over expression. (NEDO)

  13. FY 1997 report on the study on lamination control technology for functional multi-element oxide thin films by complex beam epitaxy (CxBE) process; 1997 nendo chosa hokokusho (sakutaisen epitaxy (CxBE) ho ni yoru kinosei tagenso sankabutsu usumaku no sekiso seigyo gijutsu ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Complex beam epitaxy (CxBE) process was proposed and demonstrated as new deposition process of multi-element oxide thin films. This process radiates excimer laser onto a metal complex target of ethylenediamine-tetraacetate complex under reduced pressure oxygen atmosphere condition in a reaction vessel to supply raw material onto a heated substrate. This process allowed deposition of YBCO123 phase hetero-epitaxial film onto a single-crystalline SrTiO3 substrate. This process was proved to be promising through study on crystal orientation, composition transcription and surface smoothness of the obtained oxide thin films. In addition, epitaxial ZnO film was also deposited onto a single crystalline Al2O3 substrate by this process. The relation between the obtained film and substrate epitaxy was examined, and photoluminescence of specimens was measured by triple wave of Nd:YAG laser. As a result, it was clarified that the epitaxial ZnO film prepared by this process is useful as laser material. 60 refs., 48 figs., 5 tabs.

  14. FY 1994 report on the results of the development of a large wind power system. Development of control technology of the array type wind power system; 1994 nendo ogata furyoku hatsuden system kaihatsu seika hokokusho. Shugogata furyoku hatsuden system no seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    This technology development aims at developing the design technology of the array type wind power system and the control technology to efficiently operate the system. As a result, the wind turbine produced by Micon was selected. The rated power is 100kW, and the number of the wind turbine is three. The three-phase short-circuit capacity at the generating end of the wind power generation facilities is 26,25 MVA, which can fully be broken. A simulation of voltage variation/frequency variation was made to grasp various phenomena of the output of the wind power system influencing the power source system and power distribution system. As a result, it was confirmed that it is possible to operate the system safely without lowering the quality of power. As to the overall monitor/control system which controls wind turbines, five wind turbines as many as possible are grid-interconnected and the number of wind turbine is to be controlled by a ratio of the total demand power to the gross generating output of wind power in the Miyako system, for the purpose of increasing the rate of equipment utilization of the wind power system also at the time of the lowest load of the Miyako system. In the operation of two-system interconnection, the gross power generating amount was 1,321,250 kWh, which increased 9.7% over the results in FY 1993. (NEDO)

  15. Study of the ablation of extra-low temperature aggregate target and the development of technology of formation of non-equilibrium high-quality functional thin films by the plume control; Gokuteion gyoshutai target no abureshon oyobi purumu seigyo ni yoru hiheiko kohinshitsu kinosei usumaku seisei gijutsu kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A study was made on factors of the formation of high-quality thin films in the pulse laser deposition (PLD) method, a synthesis method of high-grade functional material thin films. In the experiment, plume current measurements using Cu target were conducted for the control of electric and magnetic fields. Especially, the measuring evaluation was made of the two-dimensional distribution including not only the central part of the substrate placed opposite to the target, but the periphery of the substrate. As a result, the following was found out. The distribution of charged particles in the plume is different in positive charge and negative charge, and the negative charge is dispersed/distributed more widely. Accelerating/decelerating effects of charged particles by the electric field are saturated when the bias voltage absolute value is approximately 100V. Ionization is promoted by giving the magnetic field, and the plume distribution is expanded. Positive charged particles of the plume in the magnetic field are decelerated. In the distribution control by giving the electric field, it is effective to think improvement of the distribution not by attracting charged particles by the electric field, but by shutting out charged particles of the same polarity. 29 refs., 75 figs., 2 tabs.

  16. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  17. Hydrogen utilization international clean energy system (WE-NET). Subtask 8. Development of hydrogen combustion turbines (development of combustion control technology); Suiso riyo kokusai clean energy system (WE-NET). Subtask 8. Suiso nensho turbine no kaihatsu nensho seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper described the fiscal 1996 developmental results of hydrogen burning turbine combustion technology in the hydrogen utilization international clean energy system (WE-NET) project. A test was conducted on an annular type combustor where oxygen is mixed with steam (inert gas) at burner and fired with hydrogen. Appropriate flame shape and cooling/dilution vapor distribution were attempted, and various data on combustion were measured for improvement. Mixture and flame holding were improved by developing a can type combustor (1) where oxygen is diluted with steam after firing oxygen and hydrogen around burner and by strengthening circulation in the combustor. Improvement such as appropriate steam distribution, etc. is needed. A can type combustor (2) was tested in which the premixed oxygen and hydrogen is supplied from scoop and fired with hydrogen. By supplying part of oxygen from the primary scoop, the residual hydrogen and oxygen concentration around the stoichiometric ratio can be reduced. Concentration of the residual oxygen can be measured by the absorption light method, but it is difficult to adopt the non-contact measuring method to hydrogen. An outlook for the gas temperature measuring method was obtained. 12 refs., 121 figs., 27 tabs.

  18. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloys'. Evaluation on final research and development (first report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    The present research work has been performing research and development of the following alloys: (1) 'single crystalline alloy' , the entire alloy being composed of one crystal eliminating crystalline boundaries as an ultra heat resistant alloy with emphasis placed on improvement in particularly the creep properties, and 'particle dispersion strengthened alloy', in which ultrafine particles of oxides are dispersed uniformly; and (2) 'ultra heat resistant and tough alloy' targeted at high-temperature toughness by using Ni-group allowing ultra plasticity forging processing by micronizing crystal particles, as an ultra plastic and highly tough alloy having better processibility than conventional alloys, and 'light-weight highly tough alloy' aimed at achieving light weight and high toughness by using Ti-group. Achievements derived from the present research and development may be summarized as follows: in alloy development, alloys having performance of the world's highest level or equivalent have been developed; a manufacturing technology to make products with complex shapes has been established by using the alloy material manufacturing technology and the alloy materials developed therefrom, where prototype components of such shapes as turbine blades and turbine disks for jet engines were fabricated successfully; and the big fruit obtained was that a large number of technological experiences were acquired from this research and development. (NEDO)

  19. Report on research achievement in relation with developing fundamental combustion control technologies in fiscal 1998. Research and development of high-performance industrial furnaces; 1998 nendo nensho seigyo kiban gijutsu no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is intended to be made on fundamental combustion control technologies applicable to high-performance industrial furnaces that can reduce energy consumption and respond to environment preservation requirements. With an intention to achieve reduction in combustion exhaust gases such as carbon dioxide and nitrogen oxides, fundamental studies will be made on factors to decide flame shapes as represented by high-temperature combustion and flame shape control by utilizing microgravity environment, and researches will be made on combustion systems. Devices required for the experiments were fabricated to evaluate critical combustion characteristics of flames in furnaces including industrial furnaces, analyze and evaluate flame control parameters, and study low-pollution combustion technologies. Experimental methods acquired by 1997 were used for the experiments under the microgravity environment. Evaluation experiments were performed on flame shape control technologies and flame radiation characteristics, and basic experiments on the low-pollution combustion technologies. With these experiments, elucidation of the combustion mechanisms was launched by analyzing and evaluating the acquired data. A flame experimenting device for high-temperature preheated air completed by fiscal 1997 was used to acquire such combustion characteristics data as NOx discharge characteristics when the high-temperature preheated air is used. Based on the result thereof, verification was carried out on simulation models. (NEDO)

  20. Research and development of the industrial basic technologies of the next generation, 'composite materials (highly functional, crystal-controlled alloys)'. Evaluation of the first phase research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'koseino kessho seigyo gokin'. Zenki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The results of the first phase research and development project for developing highly functional, crystal-controlled alloys as the basic technologies of the next generation are evaluated. The R and D themes are selected to develop alloys superhighly resistant to heat, heat-resistant/high-rigidity and light/high-rigidity by controlling their crystals. Development of the basic techniques for these materials is of high significance, and highly rated. The efforts in the first-phase R and D project are aimed at designs of a total of 12 types of single-crystal alloys by the computer-aided alloy designing techniques, production of these alloys on a trial basis, and evaluation of their characteristics, for the alloys superhighly resistant to heat. Two of them are confirmed to be superior to the others, and selected as the alloys to be developed. This project has also established the single-crystal casting techniques, which allow crystal orientation almost completely. Various types of heat-resistant/high-rigidity and light/high-rigidity alloys are designed, produced on a trial basis, and evaluated for their characteristics. As a result, one alloy type is selected for each category. The other techniques developed by this project include those for adjusting powders for light/high-rigidity alloys whose average grain sizes are controlled and impurity contents are reduced. Bright prospects have been obtained for the techniques for superplastically forging the disk shapes. These efforts have almost achieved the development objectives of the first-phase R and D project. (NEDO)

  1. Research and development of basic technologies for next generation industries, 'high-performance crystalline controlled alloy'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Koseino kessho seigyo gokin (saishu kenkyu kaihatsu hyoka 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-05-01

    A proposal was given on a new processing process to use Ni-group super alloy, and elucidation was given on super plasticity phenomenon by using non-destructive tests. The Ni-group super heat-resistant alloy Mod. IN-100 subjected to different preforms by means of extrusion was given a super plasticity test at 1,050 degrees C to derive total elongation and 'm' value. As a result, it was disclosed that a material annealed for one hour at 1,070 degrees C after extrusion of 70% at 1,100 degrees C possesses the maximum 'm' value in the vicinity of 2.0 times 10{sup -2}s{sup -1}. The largest key to the new processing method is to improve the nature of the material, in which the plasticity manifestation velocity is accelerated by ten times to the order of 10{sup -2}s{sup -1} as described above. In addition, forging of IN-100 was made possible by using the ordinary forging equipment with the use of two-fold measures. The measures consist of maintaining temperature of IN-100 during casting by heating the die material to about 600 degrees C, rather than keeping it at a constant temperature, and then packing IN-100 in S35C steel material to accommodate the temperature decrease during casting inside the S35C pack. Thus, a processing method was made practical, eliminating need of the forging process to compress and solidify powder itself, that is the extrusion process. (NEDO)

  2. Fiscal 1997 survey report. Subtask 8 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen combustion turbines/development of combustion control technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system (WE-NET) subtask 8 suiso nensho turbine no kaihatsu nensho seigyo gijutsu no kaihatsi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the development of hydrogen combustion turbines, the paper described the fiscal 1997 results. As a hydrogen/oxygen combustor, the annular combustor was studied. Based on the results obtained by the last fiscal year, a combustor for the evaluation test was designed/fabricated. Oxygen is mixed with vapor at the portion of the burner, rotated/jetted (flame held by the circulation flow generated) and made to burn with hydrogen (porous injection). The smooth ignition and equilibrium wall temperature distribution were made possible. Concentrations of the residual hydrogen/oxygen in the stoichiometric mixture ratio combustion were both less than 1%. Further, can type combustor I is a type in which hydrogen and oxygen are burned near the burner and then are diluted by vapor. Improved of the burner structure and diluted vapor hole, it was tested. In can type combustor II, a mixture of oxygen and vapor is supplied and burned with hydrogen. The appropriate supply of oxygen was 20% distribution to the primary scoop and 80% to secondary. In both combustors, smooth ignition was possible, and concentrations of the residual hydrogen/oxygen in the stoichiometric mixture ratio combustion were controlled at minimum (approximately 1%). The evaluation method for the optimum hydrogen/oxygen combustor was studied. 142 figs., 24 tabs.

  3. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

  4. Achievement report on research and development in the Sunshine Project in fiscal 1980. Research on a hydrogen manufacturing technology by using thermo-chemical method. (Research on equipment materials for iodine system cycle); 1980 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu seika hokokusho. Yosokei cycle no sochi zairyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This paper describes research on materials of equipment for the second stage reaction in relation with development on a hydrogen manufacturing technology by using the iodine system cycle in the thermo-chemical method. The second stage reaction produces MgO, I{sub 2} and O{sub 2} by decomposition of Mg(IO{sub 3}){sub 2} at 600 to 650 degrees C. Corrosion tests were carried out by using 25Cr-20Ni steel and Ni-50Cr alloy having shown relatively high corrosion resistance in the researches to date, which were added with trace amount of different alloy elements. The tests were performed in gas mixture of I{sub 2}, O{sub 2} and H{sub 2}O at 600 to 700 degrees C for 48 to 192 hours. The average corrosion rate of 25Cr-20Ni steel was reduced by adding Y(0.2%), Ca (0.2%) or Si+Al (1%Si+1%Al), by which relatively uniform corrosion pattern was shown, and the corrosion resistance was improved remarkably. The average corrosion rate of 25Cr-20Ni steel showed a trend of increasing by adding Si and Nb, and non-uniform corrosion like pitting has occurred, revealing that it is not preferable from the aspect of corrosion resistance. The average corrosion rates of the tested materials tended to become somewhat greater under heat insulated condition than under continuously heating condition. Effect of Mg(IO{sub 3}){sub 2} deposition is very small. (NEDO)

  5. `Joint Research and Development of Industrial Technology,` an international research collaboration for fiscal 1997. Utilization of 3D-woven C/C composite materials to machine components; 1997 nendo kokusai kenkyu kyoryoku jigyo `sangyo kiban gijutsu kyodo kenkyu kaihatsu`. Sanjigen ori C/C composite zairyo no kikai buhin eno oyo ni kansuru kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A polygonal mirror in a printer and the main shaft of a high-speed milling machine are used as models for the development of technology for applying C/C (carbon/carbon) composite materials to machine components that are required to turn at high speeds. Various C/C composites are tested for flexural strength and thermal expansion for the designing and manufacturing of C/C composites for the polygonal mirror and main shaft. The first coating on the C/C composite is deposited by laser/plasma hybrid spraying, and is a Mo coating. A spraying robot is experimentally built for homogeneous coating. In the case of polygonal mirror, an Al coating is deposited further by the gas-deposition method. The polygonal mirror proves excellent in both dimension and reflectance, and attains the target speed of 45,000rpm. In the case of milling machine main shaft, however, it is not strong enough to withstand 40,000rpm although it is a success from a viewpoint of coating technology and manufacturing technology. 15 refs., 33 figs., 13 tabs.

  6. FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 8. Development of hydrogen combustion turbine and ultrahigh-temperature materials; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 8 (suiro nensho turbine no kaihatsu/chokoon zairyo no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Summarized herein are the materials designs/production and tests/evaluation results of heat-resistant materials, i.e., alloys, ceramic composites and carbon-based composites, which are expected to be applicable to the hydrogen combustion turbines. These have been studied since 1993, and this paper summarizes the overall evaluation results of the phase I program. The intermetallic compound as one of the candidate materials has a high-temperature strength in a range from 1200 to 1400 degrees C by optimizing elements added. However, no prospect is obtained for heat resistance at 1700 degrees C or more for the material not coated or cooled moderately. Each of the other candidate materials tested shows a bright prospect of applicability at the base material and specimen levels. The single-crystal superalloy for hybrid cooling structures has novelty in that it is free of Cr but incorporated with Si and Hf, showing approximately 10 degrees C higher heat-resistant temperature than CMSX-4. CMC and C/C are inherently excellent heat-resistant materials, and are attractive advanced composites, because they are expected to realize no-cooled blades at 1700 degrees C. (NEDO)

  7. Research and development of basic technologies for the next generation industries. Summary of research achievements in fiscal 1992 (Research and development of superconductor materials and superconductor elements); Jisedai sangyo kiban gijutsu kenkyu kaihatsu 1992 nendo no kenkyu seika no gaiyo. Chodendo zairyo chodendo soshi no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-05-01

    With an objective to establish basic technologies, research and development has been carried out to make it possible to utilize high-temperature superconductor materials in terms of engineering in the fields of electronics and electric power. In the research on superconductor materials in fiscal 1992, it was discovered from measurements of temperature change in polarization dependent EXAFS in thin YBCO film grown on an MgO substrate that relative displacement in copper atoms in CuO{sub 2} plane and peak oxygen, and relative displacement in copper atoms on a primary chain and peak oxygen show apparent increase at the critical superconduction temperature. It was verified that this phenomenon does not occur in materials that do not show superconduction. In the research and development of superconductor elements, full-swing research has begun toward establishing the following technologies: process technologies for a substrate that meets requirement of surface flatness required in electronic elements, a superconductor thin film that assures uniformity in interface composition and the laminated thin film tunnel junction that combines the superconductor thin film, an inter-layer insulation film, and ultra-fine processing to suppress deterioration, and a tunnel element technology as a technology to put the above technologies together. (NEDO)

  8. Fiscal 1999 achievement report on research and development of industrial technology of new industry creation type. Research and development of intelligent material and structural system (Development of energy use rationalization technology); 1999 nendo chiteki zairyo kozo system no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Fiber or foil shaped sensor materials and actuator devices were integrated with composite materials and composite material structures for processing and controlling information, and then studies were conducted about materials and structural systems for enabling real-time detection of damage in materials and structures, examination of soundness, control of noise and vibration, and the like. Concerning optical fiber sensors in the development of smart manufacturing technologies, the impact imposed on composite materials by sensors embedded therein was investigated, and the scope of their applicability was determined. In the development of actuator materials and devices, ceramic actuators were fabricated by microwave sintering, and it was found that they were higher in performance by 30% than actuators of the conventional design. In the testing of demonstrators, molded body monitor basic tests using optical fiber sensors were conducted for jet engine static vane models, and temperature dependence of optical intensity was understood. (NEDO)

  9. Achievement report on research and development of the industrial basic technologies of the next generation in fiscal 1985. Research and development of composite materials (Separate edition (1)); 1985 nendo jisedai sangyo kiban gijutsu itaku kenkyu seika hokokusho. Fukugo zairyo no kenkyu kaihatsu (bessatsu 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    Described herein are the results of the research and development project for developing composite materials as the basic technologies of the next generation, for patent/utility application situations, know-how techniques, processing procedures, computer code lists, and database/file lists. A total of 81 inventions are applied for patents and 3 inventions for utilities, of which 8 inventions are applied to the foreign countries. The know-how techniques developed by the project include basic testers for continuous molding of closed sections, systems for continuously withdrawing the molded articles, hot rolling molding processes which use no rolling jigs, and HIP processes for aluminum-based powders. A total of 10 processing procedures are drawn, including those for monolithic molding of panel structures, monolithic molding of planar and angled PGI/CF, production of carbon fiber/aluminum-based wire reforms, pressing, rolling, HIP molding, and melt/extrusion molding. The computer code lists include strength/rigidity/vibration optimization programs, buckling optimization programs, and impact analysis/two-dimensional of the composite materials. (NEDO)

  10. Fiscal 1997 survey report. Subtask 8 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (R and D of hydrogen combustion turbines/development of ultra-high temperature materials); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 8 suiso nensho turbine kenkyu kaihatsu chokoon zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the application to hydrogen combustion turbines, the R and D were continued of heat resistant alloys, ceramic composite materials, and carbonaceous composite materials. In the development of highly efficient super alloy single crystal materials, as to the single crystal alloy (Ni-5.3Al-0.5Ti-6.0Mo-4.8W-6.0Re) and an alloy made by adding 0.15%Si to the above alloy and an alloy made by adding 2.0%Hf to the above alloy, data on high temperature tensile property and creep rupture property were obtained, and it was confirmed that Hf added alloys were excellent in strength. Relating to the development of fiber reinforced ceramics, materials for trial fabrication were fabricated by the CVI method using SiC fiber, and the evaluation test was conducted to obtain the basic data. Besides, the following were carried out: study of coating for heat resistant alloy cooled blades, development of ceramic composite materials, development of ceramic multi-structure materials and analysis of fracture behaviors under the ultra-high composite environment, development of 3D fiber reinforced composite materials, development of technology to evaluate basic properties of ultra-high temperature materials, etc. 46 refs., 217 figs., 43 tabs.

  11. Achievement report for fiscal 1982 on Sunshine Program-entrusted research and development. Research on hydrogen production technology using thermochemical process (Research on materials for devices for iodine-based cycles); 1982 nendo netsu kagakuho ni yoru suiso seizo gijutsu no kenkyu seika hokokusho. Yosokei cycle no sochi zairyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    The research involves tests and studies conducted for the evaluation of corrosion resistance of various metallic materials in molten iodine and for the selection of materials to stay usable under iodine-handling conditions. In fiscal 1982, an iodine transportation system is studied, and corrosion tests are conducted for panels of carbon steels, various stainless steels, titanium, niobium, tantalum, etc., of the grade available in the market, under the conditions where the temperature is 113-170 degrees C, I{sub 2} contains 0-10wt% H{sub 2}O, and the gas phase is of N{sub 2}+O{sub 2}. It is made clear as the result that the effect of water present in I{sub 2} is fairly grave while the influence is but a little of the intensity of temperature and the amount of O{sub 2} gas on the corrosion rates of the respective materials, that materials other than niobium and tantalum are not usable as corrosion resistant materials, etc. In a real device, it is recommended that composite materials be used in the form of a liner or the like because both niobium and tantalum are high-cost materials and therefore create economic disadvantages if employed for the construction of pipes, heat exchangers, etc. (NEDO)

  12. FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the high function control system for power generation; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Hatsuden'yo kokino kanri system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the FY 2000 results. Items for study were as follows: 1) original production technology of substrates; 2) original production process technology of mechanically high function materials; 3) comprehensive survey; 4) formation of common basement technology. In 1), for the purpose of developing carbon materials with heat resistance and corrosion resistance in the oxidation atmosphere at 650 degrees C or more, the development of the rail gun spraying method and the device was conducted. It enabled the spraying of high melting point/high hardness materials. It was very difficult to do it by the existing technology. In 2), subjects are the composition gradient film forming technology, large area film forming technology, etc. By making positive use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected of frontier carbon materials, it is planned to apply them to the operational part of various industrial machines and for the protection of the surface of high temperature members. In 3), study was made to widen the application field of frontier carbon materials excellent in environmental harmony by the mechanical field. In 4), R and D were carried out of the basic theory/principle/conception, realization of them, systematical arrangement, acquisition/arrangement of the data on new characteristics. (NEDO)

  13. Report on achievements in fiscal 1999. Research and development of carbon-based high-function material technologies (research and development of ocean bottom petroleum production system); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    As part of the research and development of carbon-based high-function material technologies, research and development has been performed on a material creating technology and a process technology to crease mechanically high-function materials. The former technology performs synthesis by using the electron excited CVD process and the explosion synthesizing process, intended to analyze the structure and properties thereof. It is intended to synthesize nitriding-based carbon films and elucidate their composition and structure by using the mass separation ion beam method and the laser beams. Synthesizing nano tubes by utilizing catalytic reactions, and investigating their properties are intended by using the thermal CVD process, plasma CVD process and arc discharge process. Elucidation is intended on the reaction and production mechanisms of carbon-based materials, theory estimation, structures possessed by the carbon-based materials, and mechanisms to manifest their characteristics. The latter technology relates to the three assignments subjected to a composition inclining film forming technology, a complex shaped film forming and micro processing technology, and a large area film forming technology. It is intended to utilize positively such properties as low friction and wear performance and high-temperature corrosion resistance expected in high-function carbon-based materials including amorphous carbon, diamond and nitrided carbon for the purpose of application to surface protection of movable parts in different industrial machines, and building materials including glasses. (NEDO)

  14. Fiscal 2000 research report on the study on new device material, measurement, and analysis technologies for data communication base improvement program; 2000 nendo joho tsushin kiban kodoka program ni kakawaru shin device zairyo keisoku kaiseki gijutsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-02-01

    Concerning the 'new device material, measurement, and analysis technologies' which is one of the important technological constituent of the data communication base improvement program, investigations were conducted as to the future direction of middle-term technology development efforts and the important tasks to discharge. Workshops were organized to deal with the subjects named below, and the results of discussion were made into a report. It is proposed in the report that common recognition be fomented about future feasibility of the development of the new device material, measurement, and analysis technologies; that presentations be made as to how the development of the new device material, measurement, and analysis technologies should be carried out in what direction; that the tasks to discharge for the new device material, measurement, and analysis technologies be clearly defined; and the like. It is also decided that findings offered by experienced people of the industrial, academic, and government circles be fully utilized at deliberation conferences and that studies be conducted for the implementation in the future of the data communication base improvement program. Materials on the 1st-4th semiconductor program study meetings and EIAJ (Electronic Industries Association of Japan)/NEDO (New Energy and Industrial Technology Development Organization) workshops are collected in the report. (NEDO)

  15. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  16. Achievement report for fiscal 1998 on research and development project for university coordinated type industrial science technologies. Research and development on platform for designing high functional materials (development for practical use of technologies related to rationalization of energy use); 1998 nendo kokino zairyo sekkei platform no kenkyu kaihatsu. Energy shiyo gorikia kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper reports research achievements in fiscal 1998 for a platform for designing high functional materials. Since coarse-grained models used in molecular dynamics (MD) simulation are diversified depending on materials, phenomena and properties, a general purpose MD engine that can simulate them freely was designed. Methods were developed to determine the potentials of coarse-grained models from the atomistic models. In polymer melts, very slow movements caused by entanglements have a substantially important role, which are difficult to be studied by usual MD simulations. Therefore, fiscal 1998 has devised a coarse-grained model to handle slow movements of straight-chain polymers, and a rheological forecast program was prepared. Studies are also being made on meso-scale structures sufficiently large as compared to atoms and on dynamic property forecast. Works were carried out to develop a simulator, in which polymeric phenomena with large spatio-temporal scale are applied with a continuity model to solve the equation thereof. Improvements were given on the hardware/software environments required for developing simulation engines and platforms for mesoscopic region. (NEDO)

  17. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  18. Report on research and development achievements in fiscal 1980 in Sunshine Project. Development of a high-temperature bed drilling technology (Research and development of bit materials); 1980 nendo koon chiso kussaku gijutsu no kaihatsu seika hokokusho. Bit zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Development is made on bit materials that can efficiently drill high-temperature ground bed to 3,000 to 5,000 m under geothermal conditions of 350 degrees C and 400 kg/cm{sup 2}. Alloy composition excellent in corrosion resistance, oxidation resistance, high-temperature hardness, and repulsion resistance without decreasing damage resistance lower than the existing products is Cr{sub 3}C{sub 2} amount of 1%, WC of 2.5 microns, and Co/(Co + Ni) of 50%. Dispersion strengthening is most suitable for a metallurgically sintered powder cutter. Adding carbide of 5% by volume or metal as dispersion strengthening particles enhances hardness almost without damaging tenacity. Compression yield has also increased. Good dispersion strengthened materials include W and WC. On cutter materials for rock drilling bits used under severe conditions of high temperatures, high pressures, and corrosion environment, natures nearly close to the target were provided, and prospect for shape provision was obtained. These natures include mechanical properties at elevated temperatures, corrosion and wear resistance, an inside strengthening method, and a surface hardening method. Dispersion strengthening by adding micro fine hard powder to the inside strengthening method was used to have obtained the intended achievement. Positioning of the metallurgically sintered powder was made clear. (NEDO)

  19. Achievement report on research and development in the Sunshine Project in fiscal 1979. Research on hydrogen manufacturing technologies (Research on equipment materials for iodine system cycle); 1979 nendo netsukagakuho ni yoru suiso seizo gijutsu no kenkyu seika hokokusho. Yosokei cycle no sochi zairyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    From among researches on hydrogen manufacturing technologies using thermo-chemistry in the Sunshine Project, discussions were given on equipment materials, with the second-stage reaction in the iodine system cycle as the object. This paper describes achievements in fiscal 1979. The reaction produces MgO, I{sub 2} and O{sub 2} from Mg(IO{sub 3}){sub 2}. Corrosion tests were performed by using test pieces made of Ni alloy, iron-Ni-Cr alloy, Ti alloy, Zr alloy, Nb and Ta. These materials are thought to have excellent corrosion resistance in high temperature gaseous phase composed of iodine, oxygen and water. Corrosion tests were carried out also by using sheet formed test pieces of 24 kinds of alloys and six kinds of commercially available non-ferrous metallic materials in different temperatures and atmospheres, mainly the iodine plus oxygen plus H{sub 2}O mixed gas atmosphere at 600 degrees C. The corrosion resistance of the tested materials can be divided into three ranks. Materials having relatively good resistance were Ni-50Cr alloy and Co group alloy. Materials having good corrosion resistance are very little affected by water content. The higher the temperature, the more the metal corrosivity has increased. Preliminary discussions were given on pipe formability in materials having good corrosion resistance as the equipment piping materials. Their mechanical properties were also tested. This paper also describes corrosion resistance tests under heat transferring condition by using pipe-formed test pieces. (NEDO)

  20. Analysis and evaluation for practical application of photovoltaic power generation system. Analysis and evaluation for thin substrate polycrystalline solar cells (compound semiconductors and their fabrication technologies); Taiyoko hatsuden system jitsuyoka no tame no kaiseki hyoka. Usumaku taiyo denchi jitsuyoka no tame no kaiseki hyoka (kagobutsu taiyo denchi zairyo oyobi seisaku gijutsu no kaiseki hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    Oyagi, H; Okada, Y; Yamaguchi, H; Shiota, T; Kuroda, S; Igarashi, O; Tanino, H; Makita, Y; Yamada, A; Kimura, S; Ohara, A; Niki, S; Shibata, H; Fons, P [Electrotechnical Laboratory, Tsukuba (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for analysis and evaluation for thin-film compound semiconductor solar cells. The study on epitaxial growth and optical properties of the thin films of CuInSe2 and CuGaSe2 evaluates the thin epitaxial films grown under various conditions, showing morphology of the defects at the interface of heteroepitaxial growth. These results are used to set the growth conditions under which a thin film of high luminescence by exciter recombination is produced. The study also gives information of luminescence transition in the vicinity of the band ends and of energy level between the bands. The study on structural analysis of the epitaxially grown thin films of CuInSe2 investigates dependence of lattice constants of the MBE-grown CIS layer on film thickness by the X-ray diffractometry based on the bond method. The study on epitaxial growth by the Se(CH3)2-halogen transfer method tests epitaxial growth of the single-crystalline Mo on a substrate of single-crystalline sapphire. 5 figs.

  1. Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of high function control system for power generation); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden'yo kokino kanri system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Fiscal 1999 results were compiled in the R and D project on frontier carbon technology. In the development of substance original production technology, thermal spraying technology was developed suitable for thick film forming, with a plan further aimed at developing carbon-based materials characterized by corrosion resistance at high temperatures of 650 degrees C or higher. This year, for the purpose of making uniform sprayed coating of non-conductive material, a cylindrical electrode type rail gun thermal spraying equipment was developed having a high speed large flow rate material powder mechanism. In addition, a powder injection mechanism was realized having a high reproducibility at a capacity of 2,000 {mu} F and a gas pressure of 9 atmospheres in argon gas injection. In the original production process technology for mechanically high functional materials, composition gradient film forming techniques for high temperature corrosion resistant materials were performed, as was research for large area film forming technology. In the research for composition gradient film forming techniques, the operation test of the high speed large flow rate material powder injection mechanism was carried out, for example, as was the examination of ion spattering forming conditions. In the R and D on large area diamond deposition technology, a performance test was carried out for a large area film forming device. (NEDO)

  2. FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-functional materials technology (R and D of highly functional management systems for power generation); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden'yo kokino kanri system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This report summarizes the FY 1998 research results of, e.g., materials creation technology, technology for creating mechanically high-performance materials, and comprehensive surveys as part of the research and development of carbon-based high-performance materials technology. For the researches on materials creation technology, electron-excited plasma CVD was used to produce the diamond-like carbon and carbon nitride films. Fine particles of BCN diamond particles were also synthesized under high temperature and pressure. For the researches on technology for creating mechanically high-performance materials, a precision film-making apparatus was introduced and adjusted, to create carbon-based coating films excellent in tribological properties (low friction and wear type) for development of compositionally inclined film making technology. For technology of large-area film making, a small-sized microwave plasma CVD apparatus was made on a trial basis and used, to develop large-area diamond film making technology. The comprehensive surveys covered synthesis technology for application of high-performance materials to machines and tools, their application to tool members, and evaluation of tribological properties. (NEDO)

  3. Fiscal 1993 R and D project for industrial science and technology. Report on results in developing methane-fueled aircraft engine (R and D on silicon-based polymeric material); 1993 nendo methane nenryo kokukiyo engine kaihatsu seika hokokusho. Keisokei kobunshi zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    R and D was conducted on silicon-based polymeric materials for structural use, for the purpose of establishing fundamental technologies such as molecular design, synthesis, material forming and evaluation method concerning silicon-based polymers, with the fiscal 1993 results summarized. In the studies of synthesis technologies of silicon-based polymeric materials having a sea-island structure, a series of polymers with an Si-C main chain structure were prepared by ring-opening polymerization of the cyclic monomers. In the studies of interpenetrating polymer network (IPN) structure forming technologies, polycarbosilanes with superior thermal stability and solvent solubility were synthesized through structural control based on molecular design. In the studies of composite structural materials between organic metallic complex and silicon-based high polymer, the compounding was carried out by introducing or blending organic metallic complex into the main chain of silicon polymer, with evaluation made on the heat resistance. The studies of silicon polymer structural materials having a ring structure were conducted on high heat resistant polymers that were obtained by dehydrocoupling polymerization with magnesia as a catalyst. (NEDO)

  4. Fiscal 1993 achievement report. International Clean Energy Network Using Hydrogen Conversion (WE-NET) technology (Subtask 8 - Research and development of hydrogen combustion turbine - Development of ultrahigh-temperature materials); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET). (Subtask 8. Suiso nensho tabin no kaihatsu - Cho koon zairyo no kaihatsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Current technologies are surveyed and tasks to discharge are extracted relating to heat resistant alloys, intermetallic compounds, ceramic based composite materials, and carbon based composite materials, which are expected to be used for hydrogen combustion turbines. Concerning oxide dispersion strengthened alloys for cooled vanes, tasks to discharge are extracted, which relate to the designing, development, and selection of vane materials, bonding layer materials, and coating materials, and to thermal barrier coating techniques and machining techniques. Concerning porous fiber reinforced ceramic materials for ceramic shells, tasks involve the elucidation of corrosion behavior and manufacturing techniques. MoSi{sub 2}, which is a promising high-melting intermetallic compound, also presents some tasks to discharge for an increase in its high strength and high ductility in an ultrahigh-temperature steam/reducing atmosphere, and for improvement in manufacturing techniques. For the carbon/carbon composite material which is the sole material usable in the ultrahigh-temperature domain of 2,000 degrees C, an analysis and evaluation method taking its anisotropy into consideration needs to be developed, and an oxidation resistant coating has to be also developed. In addition to the designing and development of these materials, development is necessary of materials testing and evaluating techniques. (NEDO)

  5. Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 10. Development of low-temperature materials; 1999 nendo suiso riyo kokusai clean energy gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 10. Teion zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on material property test under liquid hydrogen environment, and development of optimum welding material and welding technique for the WE-NET plan. In the study on material properties in a liquid hydrogen temperature range, fatigue strength tests of base metals and weld metals were conducted under liquid hydrogen environment continuously, and further fatigue data were collected. As a result, it was clarified that both SUS304L and SUS316L have extremely high fatigue strength. To improve the tenacity of candidate weld metals under liquid hydrogen environment, material tests of welds were conducted on the laser-welded stainless steel joint and friction stir- welded Al alloy joint prepared by TWI (The Welding Institute) in the U.K. The laser-welded stainless steel joint showed higher low-temperature tenacity and lower ductility than TIG- welded joints. The friction stir-welded Al alloy joint showed extremely improved tensile strength and tenacity in a liquid hydrogen temperature range. For the low-temperature material database, both addition of new data and improvement of software were promoted. (NEDO)

  6. FY 2000 report on the results of the R and D of 'frontier carbon technology.' R and D of a system to support production of undersea oil; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the results of the FY 2000 R and D of frontier carbon technology (FCT). In Chapter 1, technology of original production of substances, new carbon-base substances such as hetero-diamond and carbon nitride with high-grade and various characteristics are synthesized. And, the following are also established: method to synthesize nanotubes, etc. in quantity, technology to control interatomic bonding, technology to control hetero-element replacement, etc. BCN films were obtained by film formation by changing the gas component ratio of diborane, methane and nitrogen by the electron beam excitation CVD method. The sp{sup 3} bonding control in carbon film was advanced. By reacting benzene with raw materials using nickel phthalocyanine as catalyst, carbon nanotube with a 60nm diameter was obtained. Using ECRCVD device, carbon fiber was synthesized on Si substrate. In Chapter 2, original production process technology of mechanical high function materials, subjects are as follows: composition gradient film forming technology, complicated morphology film formation/micro processing technology, technology to apply carbon-base materials to tribology. The application of the materials to the movable part of various industrial machines is considered by making use of characteristics such as low friction and low abrasion which are expected of amorphous carbon, diamond, carbon nitride, etc. (NEDO)

  7. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  8. FY 1993 report on the results of the subsidy project for the Sunshine Project. Development of coal use hydrogen production technology (Support study of pilot plant - Trial development of materials of plant use equipment); 1993 nendo Sunshine keikaku hojo jigyo seika hokokusho. Sekitan riyo suiso seizo gijutsu kaihatsu - Pilot plant no shien kenkyu (Plant yo kiki zairyo no shisaku kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    As to the development of coal use hydrogen production technology, the paper made the test study on the improvement of gasifier use materials and evaluation of the characteristics, the evaluation test in the environment using the actual machine, etc., and the FY 1993 results were reported. The results of the study were as follows. Concerning the shaped refractory for gasifier hearth, it was found that high chromia base and picrochromite base refractory development materials had much more excellent coal slag resistance than other existing component-system materials. It was shown that the development materials began to deteriorate under the coal gasification environment at temperatures of about 1,500 degrees C or higher. As to the mullite ceramics, a possibility was shown of improving the slag permeation resistance by making the crystal grain coarse by long-time sintering. By the survey of the state of damage of the proposed materials (refractory and iridium) used in the operational environment of the pilot plant, the outlook for use limit was made clear. In the environment test using the actual machine on the proposed metal base alloy of the typical equipment of the pilot plant, the correspondence between the operational environment and material corrosion was made clear. (NEDO)

  9. FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-functional materials technology (R and D of highly functional management systems for power generation); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden'yo kokino kanri system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This report summarizes the FY 1998 research results of, e.g., materials creation technology, technology for creating mechanically high-performance materials, and comprehensive surveys as part of the research and development of carbon-based high-performance materials technology. For the researches on materials creation technology, electron-excited plasma CVD was used to produce the diamond-like carbon and carbon nitride films. Fine particles of BCN diamond particles were also synthesized under high temperature and pressure. For the researches on technology for creating mechanically high-performance materials, a precision film-making apparatus was introduced and adjusted, to create carbon-based coating films excellent in tribological properties (low friction and wear type) for development of compositionally inclined film making technology. For technology of large-area film making, a small-sized microwave plasma CVD apparatus was made on a trial basis and used, to develop large-area diamond film making technology. The comprehensive surveys covered synthesis technology for application of high-performance materials to machines and tools, their application to tool members, and evaluation of tribological properties. (NEDO)

  10. Report on the results of the fiscal 1997 international research cooperation project. `Joint R and D industrial base technology` (development of functionally graded materials); 1997 nendo kokusai kyoryoku jigyo. `Sangyo kiban gijutsu kyodo kenkyu kaihatsu` keisha kinosei zairyo no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing functionally graded materials (FGM/LB) of thermal stress relaxation heat resistant large bulk state which are adoptable to high efficiency engine members, conducted in fiscal 1997 as intermediate target were the experiment for enlargement of the sintering process of FGM/LB with bore of up to 100mm, evaluation of physical properties, the basic development of the fabricating system facility for the commercialization. In the development of heat resistance use FGM/LB fabrication technology, to obtain ZrO2(3Y) stainless steel system FGM/LB, the following were fabricated in each bore size of 50-100mm by the research use large discharge plasma sintering machine: sintered bodies of ceramics/metal single substrate materials and mixed layer single substance materials, and FGM/LB sintered bodies without separation and crack which are composed of 9 intermediate graded layers. The survey was also made on the optimal composition and optimal sintering conditions toward the enlargement without unevenness. In the evaluation of physical properties, ZrO2(3Y)/stainless steel system was selected and test pieces were fabricated to obtain basic data on texture observation, distribution of hardness, fracture toughness, high temperature abrasion resistance, thermal expansion rates, etc. 27 refs., 108 figs., 43 tabs.

  11. FY 2000 report on the results of the new regional consortium R and D project - Immediately effective type new regional consortium R and D. Study of the developmental technology for high-density recording materials using inverter plasma; 2000 nendo chiiki shinsei konsosiamu kenkyu kaihatsu jigyo - Sokkogata chiiki shinsei konsosiamu. Inbata purazuma wo mochiita komitsudo kiroku zairyo kaihatsu gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of reducing the price and size of large-capacity hard disk drive (HDD), using inverter plasma technology, developmental study was conducted of production technology of substrate for HDD using blue sheet glass as a main material and film formation technology in the media for HDD, and the FY 2000 results were reported. In the development of low-cost glass substrate, formation technology of the barrier layer to block the elution of alkali component was developed for blue sheet glass substrate. As to the development of formation technology of low-cost recording layer, developmental study was made of technology of formation of the layer as undercoat of magnetic recording layer onto the barrier layer. As a result of the experiment, the following were confirmed: metal chromium is well fit for the barrier layer and can be a proposed material of undercoat; it is possible to construct the magnetic media layer on the glass substrate. Concerning the development of the inverter plasma film formation unit, a unit was developed where it is possible to form the film of blue sheet glass substrate with a size of 3.5 inches. (NEDO)

  12. Fiscal 1998 achievement report on regional consortium research and development project. Venture business raising type regional consortium - small business creating base type (Research and development of new functional natural materials and development of technologies for their commercialization); 1998 nendo shinkino tennen zairyo no kenkyu kaihatsu oyobi sono kogyoka gijutsu no kaihatsu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts are made to manufacture a surgical membrane provided with a tissue regenerating capability and to bring the product into mass production and then commercialization. Subjected to examination is a composite of three materials, which are collagen from enzyme extracted pigskin which is a natural macromolecular material known to be safe, gelatine, and the polyglycollic acid which is a synthesized macromolecular substance to be disintegrated and absorbed in vivo. As for mass production technology, the product which used to be manufactured sheet by sheet in a laboratory is now produced lot by lot, each lot comprising 30-50 sheets. The sheet is now guaranteed to be excellent in quality, physical property, and safety. The product dimensions are now 10 times 10cm, large enough to ensure practicability and mass-production. It is found that the membrane is an integrated 3-layer structure, that its strength is more than what is stipulated concerning one-point support tension, rupture tension resistance, etc., and that it passes tests involving cytotoxicity, chromosome aberration, back mutation, cutaneous sensitization, fever causing substances, etc. A canine test reveals that the product works effectively as a material for regenerative medicine. (NEDO)

  13. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems; 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development of the basic technology of the structure system which has the same intelligent functions as living body such as perception, decision and response through information processing/control (brain) by integrating advanced complex material structure (skeleton), fiber or film sensor material/device (nerve) and actuator material/device (muscle). This report describes the fiscal 1998 research result. On health monitoring technology, study was made on development of high-performance sensors, and a damage detection and self-diagnosis system for structural integrity. On active adaptive structure technology, study was made on improvement of a quasi-elastic behavior model for shape memory alloys, and a candidate actuator for noise and vibration reduction. On actuator materials and devices, study was made on the relation between electronic properties and dielectric/electro-strictive characteristics of the latest advanced ceramic materials available. Creation of silent smart structure was also clarified. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends. (NEDO)

  14. Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development project on high-speed deformation characteristics evaluation methods for metallic materials; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo. Kinzoku zairyo no kosoku henkei tokusei hyoka hoho no kenkyu kaihatsu jigyo - Gyomu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to develop methods for evaluating the characteristics of metallic materials experiencing high-speed deformation or impact deformation. The research was conducted by the research WG (working group) consisting of some participants of an international conference convened this fiscal year. The research result revealed that studies in Japan lopsidedly dealt with metallic materials at strain velocity of 10{sup 4}/second or less, such as steel, while many studies overseas dealt with materials other than metals at strain velocity over 10{sup 4}/second. The test and evaluation WG conducted high-speed tension tests for T6-treated aluminum alloys using the split Hopkinson bar method, hydraulic servo method, one bar method, and the sensing-plate method for measuring force, and the results were compared. It was then found that the one bar method produced disturbance more remarkably than the others and that the loading block structure and load rise time influenced the emergence of the peak load. The emergence of a peak load in the Hopkinson bar method or the one bar method had been predicted on the basis of the research conducted by the analysis group. (NEDO)

  15. Fiscal 1992 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Development of high efficiency power generation component creation technology); 1992 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai no sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Studies were made to develop technologies for creating carbon based advanced composite materials for use under extreme environments, and a comprehensive technology survey was conducted in this connection. Studied in the comprehensive survey were coordination between various technology developing activities, research on trends of relevant technologies, and technical tasks to discharge for the development of materials usable under extreme environments. In addition, interim evaluation was performed. Carried out in the development of C/C (carbon/carbon) composite materials using coal pitch derived fibers were carbon matrix optimization and studies of rupture mechanism, and the fabrication of specimens by compounding and molding under the hot press method and HIP (hot isostatic process). Carried out in the development of C/C composite materials using PAN (polyacrylonitrile) based carbon fibers were studies of rupture mechanism and the like, fabrication of specimens by compounding and molding, and performance enhancement under the high pressure impregnation carbonization method and the like. Oxidation resistant coatings were fabricated and tested for performance, and preliminary experiments were conducted toward the development of a novel coating technology. (NEDO)

  16. Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 10. Development of low-temperature materials; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 10. Teion zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the development of candidate low-temperature materials for liquid hydrogen transportation and storage (including mother materials and welds) for WE-NET. Evaluation tests were performed on material properties (mechanical properties, low-temperature embrittlement, and hydrogen embrittlement sensitivity) under room temperature and low temperature regions including liquid hydrogen atmosphere. Low temperature toughness of welds was assessed particularly to identify characteristics of different welding methods developed newly for improvements. The stainless steels and the mother materials of aluminum alloy selected as the candidates have sufficient characteristics even under the liquid hydrogen atmosphere, but the welds have lower low-temperature toughness, requiring improvement. For the stainless steels, since the amount of {delta} ferrite in welds affects greatly the low-temperature toughness, adoption of complete austenite type welding metal is effective. The reduced pressure electron beam welding method can enhance drastically the low-temperature toughness of stainless steel. For the aluminum alloy, it can be one of the alternatives to use an alloy system with composition of high low-temperature toughness. The friction stir welding method for the aluminum alloy was found to provide extremely high low-temperature toughness, which can be evaluated as a new welding method. (NEDO)

  17. FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the high function control system for power generation; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Hatsuden'yo kokino kanri system kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the FY 2000 results. Items for study were as follows: 1) original production technology of substrates; 2) original production process technology of mechanically high function materials; 3) comprehensive survey; 4) formation of common basement technology. In 1), for the purpose of developing carbon materials with heat resistance and corrosion resistance in the oxidation atmosphere at 650 degrees C or more, the development of the rail gun spraying method and the device was conducted. It enabled the spraying of high melting point/high hardness materials. It was very difficult to do it by the existing technology. In 2), subjects are the composition gradient film forming technology, large area film forming technology, etc. By making positive use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected of frontier carbon materials, it is planned to apply them to the operational part of various industrial machines and for the protection of the surface of high temperature members. In 3), study was made to widen the application field of frontier carbon materials excellent in environmental harmony by the mechanical field. In 4), R and D were carried out of the basic theory/principle/conception, realization of them, systematical arrangement, acquisition/arrangement of the data on new characteristics. (NEDO)

  18. Research and development of basic technologies for the next generation industries, 'light-reactive materials'. Evaluation on the second term research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'hikari hanno zairyo'. Dainiki kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Research and evaluation was performed with an objective of establishing the basic technology related to light-reactive materials that control the structures and status of aggregation of molecules by using actions of light, and can be used for ultra-high density recording, high resolution indication and light switches. In elucidating the basic characteristics of photochromic materials, a non-destructively readable recording system was proposed and demonstrated, highly durable and high-functional photochromic compounds were developed, and a number of material design guidelines were accumulated to realize characteristics required in light-beam recording. With regard to development of the photochromic materials, realization of photochromic thin films that can record wavelengths in multiplex manner has become more realistic. For elucidating basic characteristics of PHB materials, a method for evaluation from a number of directions including the time method for photon echo was established in addition to the conventional frequency recording characteristics. Regarding the elucidation of the PHB phenomenon, demonstration was carried out on intermediate zone structure control in diversified material systems including living organism substances, where a large number of findings were accumulated. (NEDO)

  19. Fiscal 1991 research report. Research trend survey for next-generation industrial structure technology research and development project - Research and development of advanced materials for extreme environments; 1991 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu project ni kakawaru kenkyu doko chosa hokokusho. Chotaikankyosei senshin zairyo no kenkyu kaihatsu (sekitoku daiene)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Efforts were exerted to develop intermetallic compounds and C/C (carbon/carbon) composites to serve as advanced materials for extreme environments. In relation with advanced materials, especially with intermetallic compounds and fiber reinforced intermetallic compound composite materials, a technical research survey was conducted covering the three fields of (1) summarization of activities conducted up to fiscal 1991, (2) contents of associated aerospace projects, and (3) aeroengine components. In Field (1), the ground on which the project was created and the project's basic plans, goals, and systems, and its ripple effects are discussed, and the fruits produced so far are summarized. In Field (2), aeroengine component related projects of America, Britain, France, Germany, and Japan are investigated. In Field (3), aluminum alloys, titanium alloys, alloy steel, superalloys, intermetallic compounds, and intermetallic compound composite materials are discussed with attention paid to their current status and future trend, characteristics they are supposed to finally assume, and technical tasks to discharge for the development of technologies concerned. (NEDO)

  20. FY 2000 report on the results of the R and D of 'frontier carbon technology.' R and D of a system to support production of undersea oil; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the results of the FY 2000 R and D of frontier carbon technology (FCT). In Chapter 1, technology of original production of substances, new carbon-base substances such as hetero-diamond and carbon nitride with high-grade and various characteristics are synthesized. And, the following are also established: method to synthesize nanotubes, etc. in quantity, technology to control interatomic bonding, technology to control hetero-element replacement, etc. BCN films were obtained by film formation by changing the gas component ratio of diborane, methane and nitrogen by the electron beam excitation CVD method. The sp{sup 3} bonding control in carbon film was advanced. By reacting benzene with raw materials using nickel phthalocyanine as catalyst, carbon nanotube with a 60nm diameter was obtained. Using ECRCVD device, carbon fiber was synthesized on Si substrate. In Chapter 2, original production process technology of mechanical high function materials, subjects are as follows: composition gradient film forming technology, complicated morphology film formation/micro processing technology, technology to apply carbon-base materials to tribology. The application of the materials to the movable part of various industrial machines is considered by making use of characteristics such as low friction and low abrasion which are expected of amorphous carbon, diamond, carbon nitride, etc. (NEDO)

  1. Fiscal 1991 research report. Research trend survey for next-generation industrial structure technology research and development project - Research and development of advanced materials for extreme environments; 1991 nendo jisedai sangyo kiban gijutsu kenkyu kaihatsu project ni kakawaru kenkyu doko chosa hokokusho. Chotaikankyosei senshin zairyo no kenkyu kaihatsu (sekitoku sekiyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Efforts were exerted to develop intermetallic compounds and advanced C/C (carbon/carbon) composite materials usable under extreme environments such as high temperatures. In relation with advanced composite materials, especially with projects for developing composite materials using oil as raw material, a survey was conducted of the three fields of (1) summarization of activities conducted up to fiscal 1991, (2) contents of associated aerospace projects, and (3) oil based composite material technology. In Field (1), past achievements are summarized. In Field (2), aerospace projects under way across the world are broken down by airframe and engine, and are reviewed from the viewpoint of needs for materials. In Field (3), the present and future of heat resisting thermosetting composite materials, thermoplastic composite materials, and C/C composites are discussed. Characteristics such materials are supposed to finally assume and tasks to discharge for technical development are also taken up. (NEDO)

  2. Fiscal 2000 report on results of project for R and D of industrial science and technology in cooperation with universities, and R and D of platform for designing high functional materials (development of energy use rationalization technology); 2000 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted concerning sophistication and high speeding in designing materials by simulation technology utilizing a new calculation method, with fiscal 2000 results compiled. A group working on coarse-grained molecular dynamics have tackled three problems such as the development and application of a multi-purpose coarse-grained molecular dynamics engine called COGNAC. A group on dynamic average domain method added various functions to a new multi-purpose dynamic average domain simulator called SUSI, and also achieved a variety of results by simulations using this simulator. A group on dispersed structure simulation has been proceeding with the development and application study of a multi-phase dynamics simulator called MUFFIN. A verification research group carried out verification of predictability, with the accuracy intended by each program, on thermal properties, optical properties, formability, etc., using polyethylene as the verification material. A platform group prepared a new high-speed platform that used less memory. (NEDO)

  3. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research and development of energy in its 2nd year (Development of energy conservation assisting measurement control technology for electronic equipment manufacturing process--Designing and tentative construction of IMI); 1999 nendo denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu seika hokokusho. 2. IMI no sekkei to shisaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the research and development of IMI (intelligent micro instrument) substrate devices, a designing method is established and, using the method, device manufacturing technologies are tested and evaluated and the results are reflected on the experimental construction of a sensor and an IC probe. In the research and development of a sensor and a sensing system, efforts are focused on a chlorine gas sensor, and a prototype No. 1 is designed and fabricated. In a test conducted in the presence of gas of 0-10ppm concentration, the prototype transmits signals that indicate excellent linearity and responsiveness. In the research and development of a probe for measuring electronic devices, efforts are made to put to practical use an IC (integrated circuit) probe of 40{mu}m pitch times 400 arrays, and specifications to develop for the probe are defined. A tentatively built cantilever structure shows values that justify its practical application. In the research and development of an IMI electronic circuit, a prototype No. 1 of a system for processing and transmitting sensor signals by radio is manufactured, which operates on the carrier frequency of 2.4GHz and sampling frequency of 4kHz. The prototype performs to achieve the goal. (NEDO)

  4. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Final year report. Development of the measuring control technology supporting energy conservation in the manufacturing process of electronics (Design and trial manufacture of IMI); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu - IMI no sekkei to shisaku (saishu nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As measures taken for energy conservation in the manufacturing plant of electronic devices/equipment such as IC, the development was proceeded with a chlorine gas radio sensing system and a liquid crystal driver IC probe, according to the survey results that it is possible to control energy consumption in air conditioning by completely furnishing poisonous gas monitor in clean room and conserve energy related to the manufacture of IC and LSI tester by using Si for IC probe cards. The following four were carried out: 1) development/trial manufacture of chlorine sensing system; 2) development/trial manufacture of LCD (liquid crystal driver) IC probe; 3) support of trial manufacture of key element technology; 4) comprehensive investigational study of IMI (Intelligent Micro-Instrument). In FY 2000, study was focused on 1) and 2). In 1), a planar type micro-structure sensor was developed, and the trial-manufactured system brought favorable results in sensitivity, response speed and reproductivity. (NEDO)

  5. Research and development project of regional consortiums in fiscal 1998. Research and development of regional consortium energy (development of measuring technology to aid energy conservation in electronic device manufacturing processes (design and trial production of IMI) (Report on the result in the first year)); 1998 nendo chiiki consortium energy kenkyu kaihatsu. Denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu (IMI no sekkei to shisaku) (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper summarizes the development of intelligent micro instruments (IMI) inaugurated in fiscal 1998 as the wide-area consortium project for the Tama area. Research and development will be carried out on the following items: IMI substrate elements utilizing micro machining technology, applicable to micro sensors and micro probes, semiconductor process sensors, electronic device measuring probes, signal processing and communication circuits for wireless sensing. This paper describes the achievements during fiscal 1998. Technologies were transferred from the Mechanical Engineering Laboratory of the Agency of Industrial Science and Technology on silicon micro machining and PZT piezoelectric thin film formation. An IMI research laboratory was installed at the Tokyo Metropolitan University. In developing the IMI substrate elements, different beams applicable to sensors and probes were fabricated on a trial basis, and their mechanical properties were measured. For the semiconductor process sensors, discussions were given on micronization on a chlorine ion analyzer. In developing the electronic device measuring probes, the target was placed on measurement of in-situ characteristics of IC chips on a wafer. A prototype transmitting and receiving circuit board was fabricated for developing the wireless sensing. (NEDO)

  6. FY 1974 report on the results of the Sunshine Project. Study on a system to refine/transport/store hydrogen and the safety technology (Investigational study of the measuring control system for safety in the stage of low temperature storage and refining of hydrogen); 1974 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso no teion chozo, seisei dankai no anzen no tame no keisoku seigyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-30

    Safety technology is necessary and indispensable for future materialization of a hydrogen energy system. The survey was made from a viewpoint of safety technology in refining hydrogen at low temperature and in storing it in a low temperature liquid state. Japan has so far had no experiences for the handling and consumption of liquid hydrogen except the partial use at laboratory. Accordingly, collected here was literature on the storage, transportation, handling, low temperature refining of the liquid, etc. The present state of technology in Japan and abroad was grasped and items in the safety relation were picked up. As to the existing literature on the hydrogen relation, there is much literature on the U.S. NASA project, and there is also much on practical business details such as the handling of a large quantity of liquid. Therefore, from each literature mostly on the above, the literature on the liquid storage, transportation use storage tank and refining method was reviewed and arranged, and at the same time, the items were picked up of the safe disposal method, disaster prevention relation, and measuring relation. The paper also arranged the results of surveying hydrogen physical properties and equipment materials which are closely related to safety general, in particular, and examples of disaster. (NEDO)

  7. Achievement report on research and development in the Sunshine Project in fiscal 1976. Researches related to hydrogen refining, transporting and storing systems, and safety assurance technologies (Surveys and researches on low-temperature storage of hydrogen, and measurement and control systems for safety in refining stage); 1976 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso no teion chozo, seisei dankai no anzen no tame no keisoku seigyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This paper discusses low-temperature storage of hydrogen, and safety in the refining stage thereof. Discussions were given on a device to discharge safely hydrogen evaporated from a liquefied hydrogen storing tank rolly. A testing equipment of a 1/10 size of a full size equipment was fabricated on a trial basis. The equipment was used to test discharging a gaseous mixture containing hydrogen at concentration of about 2%, while air is being supplied from a blower directly connected to a gas motor (rotating on gas pressure) with treatment rate of 15 Nm{sup 3}/h. In order to keep the hydrogen concentration below the lower explosion limit of 4%, uniformity in the spatial distribution of the concentration is important. Full consideration should be given thereto in future designing works. With a cryogenic adsorption refining device for hydrogen, oxygen content is adsorbed, and hydrogen is refined. During regeneration of the adsorption device, oxygen is discharged. Experiments on regeneration methods were performed for comparing and discussing oxygen discharge behavior by using three systems: nitrogen purge, hydrogen purge, and temperature raising. Cases were found in which oxygen concentration in the exhaust gas exceeds the lower explosion limit of 4%. There is a number of important assignments to assure safety, including specific measures to prevent the above excess, reciprocal influence of multiple impurities, and removal of ignition sources. The present experiments have great significance in providing fundamental items of information. (NEDO)

  8. Fiscal 1975 Sunshine Project research report. Research on refining, transport and storage systems for hydrogen, and their safety technologies (Research on measurement/control system for safety management in low-temperature storage and refining processes of hydrogen); 1975 nendo suiso no seisei, yuso, chozo system oyobi hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso no teion chozo, seisei dankai no anzen no tame no keisoku seigyo system ni kansuru kenkyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-05-28

    The following were selected as themes necessary and important for the safety of the forthcoming hydrogen energy system, based on the fiscal 1974 document survey result, and the fiscal 1975 research results. First as for low- temperature storage of hydrogen, since safe discharge of hydrogen gas generated in a storage tank is important, gas motor discharging usually used for such transport tanks as tank lorry, and burn bond discharging suitable for discharge of a large amount of hydrogen were selected as test items. Next as for storage and transport of low-temperature hydrogen such as liquid hydrogen, a low-temperature control valve to control the amount of liquid hydrogen for transport was selected as a test item. Under the assumption of the model tests on the above 3 items in fiscal 1976, various studies and trial designs were made on concrete test equipment. The test plans were also prepared for some ones among them. (NEDO)

  9. Computer aided materials design; Keisanki zairyo sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The questionnaire survey on the computer aided materials design (CAMD), and the survey of current domestic and overseas software concerned were carried out to clarify developmental issues. The current elementary technology of CAMD was also surveyed to study its several problems caused with a progress of material design technology due to drastic diffusion of CAMD. This project aims at establishment of a new demanded software, computer chemistry, focusing attention on functional materials such as catalyst, polymer and non-linear electronic materials. Microscopic simulation technology was mainly surveyed in fiscal 1996. Although some fruitful results have been obtained in the fields of medical and agricultural chemicals, organic compounds, proteins, catalysts and electronic materials, such some problems are pointed out as `CAMD cannot handle an actual size of the target system` and `commercially available software are very expensive.` Reliable tool development as elementary technology, and the verification of its applications are thus required. Meso-dynamics, polymers, surface reaction and integrated technological environment attract users` attention. 27 refs., 16 figs., 2 tabs.

  10. Aircraft and ancillary materials. 2. ; Engine materials. Kokuki to sono shuhen zairyo. 2. ; Engine zairyo

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-05

    This paper summarizes materials for aircraft engines. Jet engines are the mainstream today, which are classified according to their operation process into a turbo jet engine, a turbo prop engine, a turbo shaft engine, and a turbo fan engine. Japan has produced 1543 engines in the past decade, almost all of which are supplied to the Defense Agency. Jet engines use mainly Ni-group heat-resistant alloys, titanium alloys and steels. Improvement of engine efficiency has caused turbine inlet temperatures to rise to 1400[degree]C to 1500[degree]C that give rise to grain boundary cracking. To prevent this, discussions are in progress on monocrystal blades replacing the conventional polycrystal precision casts. Intermetallic compounds including Al/Ti are expected especially of use as jet engine constructing materials from their high melting point and formability. Discussions are preceding on ceramics as to coating them intended of improving heat resistance. Composite materials have a problem of insufficient mechanical strength remaining unsolved. 8 figs., 5 tabs.

  11. Combustion synthesis of inorganic materials; Muki zairyo no nensho gose

    Energy Technology Data Exchange (ETDEWEB)

    Oyanagi, M. [Ryukoku University, Kyoto (Japan)

    1999-11-01

    Combustion synthesis of porous titan carbide is outlined. In combustion synthesis, exothermic chain reaction, which is induced by igniting at one point of the simple substance mixture, propagates the combustion wave, and the compound is synthesized, which can be sintered by it. By this method, to this day intermetallic compounds, ceramics and high melting point composite materials have been synthesized, and synthetics can be made compact by adding pressure during or just after the reaction. Recently, applying the induction heating jointly, preheating before the reaction and heat treatment after the reaction can be controlled, accordingly, many high melting point inorganic compounds and composite materials can be made by combustion synthesis under pressure. (NEDO)

  12. Development of artificial soft rock. Jinko nangan zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kishi, K.; Nishioka, T. (The Tokyo Electric Power Co. Inc., Tokyo (Japan)); Nojiri, Y.; Kurihara, H.; Fukazawa, E. (Kajima Corp., Tokyo (Japan))

    1990-09-15

    When a part of the ground is replaced with artificial materials in the construction of important structures on soft rock foundations, it is desirable for the artificial materials to have the rigidity equivalent to that of the surrounding ground and to be stable in the long term. The article reports a success in the development and utilization of artificial soft rocks satisfying the above conditions by using a raw material produced locally at the construction site. The soft rock aimed at was mudstone belonging to the Neocene period, and the artificial material of soil-mortal system is selected as the equivalent having the same physical properties. Improvements in selection of solidification agents and cohesive soil were especially contrived: taht is, a new material for solidification was developed by mixing blast-furnace cement and gypsum; and the mudstone on the site was used as the cohesive soil by slurrying it to adjust its grain size to homogeneous composition. The artificial soft rock resulting from the above contrivance showed excellent flow, self-leveling, and filling properties at the stage of fresh mortar, and the physical properties after hardning was very similar to those of the natural ground. The long-term stability was also confirmed by the tests on hydration reaction and environmental factors. 2 figs., 1 tab.

  13. New alloys for structural application. Kikai kozoyo shin kinzoku zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, T [Kogakuin Univ., Tokyo (Japan)

    1993-01-15

    As recent advance on the scientific technologies is amazing, the materials having new function or excellent performance have been developed. Speaking on some recent examples, they can be divided roughly to one group belonging to invention of materials themselves such as oxide superconductors and compounds semi-conductors, and the other belonging to the products as invention of epoc-making material manufacturing methods such as noncrystalline alloys and particle dispersion reinforced alloys (ODS). In this report, first, some new metallic materials introduced relatively recently and converting many technical innovations in wide range of machinery field, such as titanium alloys, refractory alloys having nickel group, aluminium-lithium alloys, HSLA steels composed of reduced weight of alloy elements and having higher strengths than those of carbon-steels and various properties, intermetallic materials such as Ni3Al and others are described, and next, mechanical alloying and its particle dispersion reinforced alloys, liquid phase rapid cooling process and its noncrystalline alloy-rapid cooling cohesion powder sintering alloys, and others are summarized under the paths from their birth to present status. 31 refs., 12 figs., 5 tabs.

  14. Development of new catalytic materials; Shinshokubai zairyo no kaihatsu doko

    Energy Technology Data Exchange (ETDEWEB)

    Tatsumi, Takashi [Yokohama National Univ., Kanagawa (Japan)

    1999-04-05

    The catalyst fulfils large role for the solution of environmental problem, resources problem, and energy problem. It is popular to carry out the research, which intends to realize the new process of which the environmental loading is low by the new catalyst. And, the development of catalyst material, which demonstrates the function under the ultimate condition like the environmental catalyst, is required. The interest has leaned in also using the solid catalyst for the synthesis of fine chemical such as intermediate and perfume of the medical supply synthesis. In this paper, the following are described as a new catalyst material: Zeolite and development trend of meso porous molecular sieve explosively studied recently. The application to the reaction is also simply touched. (NEDO)

  15. Packaging material and aluminum. Hoso zairyo to aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Itaya, T [Mitsubishi Aluminum Co. Ltd., Tokyo (Japan)

    1992-02-01

    The present paper introduces aluminum foil packaging materials among the relation between packing materials and aluminum. The characteristics of aluminum foil in the packaging area are in its barrier performance, non-toxicity, tastelessness and odorlessness. Its excellent functions and processibility suit best as functional materials for food, medicine and industrial material packaging. While an aluminum foil may be used as a single packing material as in foils used in homes, many of it as a packaging material are used in combination with adhesives, papers or plastic films, or coated or printed. It is used as composite materials laminated or coated with other materials according to their use for the purpose of complementing the aluminum foil as the base material. Representative method to laminate aluminum foils include the wet lamination, dry lamination, thermally dissolved lamination and extruded lamination. The most important quality requirement in lamination is the adhesion strength, which requires a close attention in selecting the kinds of adhesive, laminating conditions, and aging conditions. 8 figs., 6 tabs.

  16. Four-quadrant speed control circuit of DC servo motor using integrated voltage control method; Den`atsu sekibunchi seigyo wo mochoiita chokuryu dendoki no shishogen sokudo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Okui, H. [Osaka polytechnic College, Osaka (Japan); Irie, H. [Osaka Electro-Communication Univ., Osaka (Japan)

    1996-08-20

    The Two-Quadrant chopper is constructed by using smoothing reactor in common of the step-down chopper and step-up chopper of the DC chopper. Furthermore, since the circuit connected in bridge type by using these two groups has both of positive and negative voltage from DC source and can supplies the current from positive and negative directions for load, it is called in general as the Four-Quadrant chopper. As the Four-Quadrant chopper may supply and regenerate power, it works as power amplifier with high efficiency. In this paper, the speed control circuit of DC servo motor using Four-Quadrant integrated voltage control circuit is described. The speed control circuit is composed of simple circuits of one adder integrator and four hysteresis comparators. The Four-Quadrant speed control circuit has a DC motor speed feedback loop and a voltage feedback loop which connects with AC, it plays the Four-Quadrant speed control without current inspection. The speed control characteristics with no steady state error over four quadrants may be obtained, changing of the quadrant is smooth and transition response is rapid. 9 refs., 11 figs.

  17. Improvement of efficiency by proportional and integral control for compact boiler; Shoyoryo boiler no renzoku seigyo (P.I seigyo) ni yoru seino kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Yanagida, T. [Kawasaki Thermal Engineering Co. Ltd., Shiga (Japan)

    1998-10-01

    Efficiency of a compact boiler is improved by the introduction of a continuous P.I. control. It is controlled by the following procedure. The proportional control, which controls magnitude of combustion in proportion to a load requirement, is combined with an integral control function which keeps steam pressure at a given level, in order to stabilize steam pressure at a level comparable to that of a large, water-tube type boiler. A stable steam pressure is realized by including control of make-up water supply, to minimize the effects of water supply on steam pressure. The effects of characteristics of the combustion valve on control are relaxed by programming. In addition to the above, rotational speed of the motor for the forced draft fan is controlled for each load level, to reduce power consumption. These bring improved quality of steam, i.e., stabilized steam pressure, improved follow-up characteristics of the steam and secured dryness of the steam. Energy-saving is also achieved, i.e., reduction of noise and power consumption at a low combustion load are achieved by improved real boiler efficiency and inverter-aided control of the forced draft fan. Low-NOx burners are adopted, to abate NOx content to 60ppm or less at any load. 16 figs.

  18. Development of a platoon driving AHS; AHS jikkensha ni okeru gunsoko seigyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Seto, Y; Inoue, H [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    Nissan and the Public Work Research Institute of the Ministry of Construction are developing an Automated Highway System. We are investigating a longitudinal control system in AHS. In this paper, a vehicle control method using two actuators an engine and a brake, is described. Experimental and simulated results are shown. A Platoon driving control method using road-to-vehicle and vehicle-to-vehicle communication is described. And the influence of the communication on the control performance is shown by experiments and simulation. The effects of the communication device and control device mentioned above are verified by experimental results in an AHS field test conducted in September 1996 on a dosed highway. 5 refs., 8 figs.

  19. Artificial control of biocatalytic reaction; Seitai shokubai hanno no jin`iteki seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K. [Kyoto University, Kyoto (Japan). Institute for Chemical Research

    1997-08-25

    Selective composition of optically active compounds by use of biocatalysts is discussed. No search is made for any particular microbes or enzymes, but predetermined ones are used. For an increase in the selective yield of L-type carnitine by reducing 4-chloroacetoacetic acid ester using baker`s yeast, the ester length should be enlarged to that of octyl ester. Just as in this case, steric control by ground substance modification is often effective. Lipase helps on esterification which is contrary to hydrolysis in an organic solvent and, even in the optical division in this process, steric control by ground substance modification (for example by changing the structure of the acyl section) is effective. Immobilization of biocatalysts for use in reaction occasionally exerts some effect on stereoselectivity. Two types of enzymes may be participating in a reaction and inhibiting selectivity, and then a two-layer system of water and organic solvent may be effective in performing steric control over the situation. Another measure is to inhibit the activity of either of the two enzymes by use of a selective inhibitor utilizing enzyme reaction. The kind of solvent is also an influential factor. 11 refs., 7 figs.

  20. Development and demonstration of optical polarization controller; Hikari henpa seigyo sochi no kaihatsu to jissho

    Energy Technology Data Exchange (ETDEWEB)

    Kurono, M. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    If fiber transmission light can be controlled in a stabilized polarization state, realization of coherent optical communication is anticipated. In the case of adopting it to OPGW, however, it is necessary to compensate high speed polarization variation caused by lightning strike. But this was difficult in the conventional method. Accordingly, a high speed polarization control method was proposed which uses an electric effect of lithium niobate (LN) crystals. In the study, a polarization control unit was manufactured based on the method proposed and the performance was demonstrated. As a result of measuring output light with input light changed in every state of polarization, the object horizontal polarization component obtained a stabilized light intensity at {+-}0.1dB, and a light intensity of the component slipped out of the horizontal polarization was suppressed under -20dB. To cope with the polarization variation by lightning strike, it is necessary to make the control delay 10{mu}sec or below, and improvement in processing unit, etc. may make it possible since LN crystals respond below 1{mu}sec. High speed control of the infinitely continuing arbitrary polarization variation became possible. 14 refs., 19 figs.

  1. Car audio using DSP for active sound control. DSP ni yoru active seigyo wo mochiita audio

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K.; Asano, S.; Furukawa, N. (Mitsubishi Motor Corp., Tokyo (Japan))

    1993-06-01

    In the automobile cabin, there are some unique problems which spoil the quality of sound reproduction from audio equipment, such as the narrow space and/or the background noise. The audio signal processing by using DSP (digital signal processor) makes enable a solution to these problems. A car audio with a high amenity has been successfully made by the active sound control using DSP. The DSP consists of an adder, coefficient multiplier, delay unit, and connections. For the actual processing by DSP, are used functions, such as sound field correction, response and processing of noises during driving, surround reproduction, graphic equalizer processing, etc. High effectiveness of the method was confirmed through the actual driving evaluation test. The present paper describes the actual method of sound control technology using DSP. Especially, the dynamic processing of the noise during driving is discussed in detail. 1 ref., 12 figs., 1 tab.

  2. Surface design of powder by precise modification; Kotai hyomen no seimitsuna kaishitsu seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Chikazawa, Masatoshi

    1999-01-01

    The progress of the recent technology is it in high performance, the one manufactured by development of the high function material. It is skillful, and the nature of this effective material is greatly influenced by the various materialities of the raw material powder and a function again. Therefore, the moment it diversifies all the more from now on, a demand for the raw material powder is thought to become more precise control than the thing of the materiality of the powder and the function. Precise quality function technology on the surface of the powder which should make the materiality of the purpose and a functional expression possible is very important to meet such a requirement. Quality silica powder is used as the sample, and you must investigate about the micro-mechanism of the water control by effective based quality of surface from such a position. (NEDO)

  3. Development of remote controlled blasting system for tunnels; Tunnel yo enkaku seigyo happa system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, S.; Kawamura, M.; Hirosaki, Y. [NOF Corp., Aichi (Japan)

    1997-06-30

    A downsized wireless blasting system has been developed for tunnel construction in the mountainous districts. This system consists of an oscillator, loop antenna, and initiator. The ac magnetic field is generated in the loop antenna using 550 Hz ac generated by the oscillator, to induce the electro motive force between both ends of receiver coil in the initiator. It is stored in the capacitor after rectification, to initiate the detonator by discharging with the firing signal. This system has been developed by downsizing the conventional RCB (remote controlled blasting system) for underwater blasting, and unmanned operation is planned in future. An oscillation frequency, 550 Hz with an actual result has been adopted. The arm length of loop antenna is 3 m, which can be installed in the tunnel. Various receiver initiators were fabricated as a trial. A convex type was adopted due to its excellent receiving performance. The receiving performance was improved by increasing the magnetic induction and decreasing the power loss. After receiving voltage of the receiver initiator was confirmed, field initiation tests were conducted. Initiating and blasting were successfully carried out. 5 refs., 15 figs., 3 tabs.

  4. Optimal control of helicopters following power failure. Helicopter no engine koshoji no saiteki hiko seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Okuno, Y.

    1993-01-01

    In order to study the optimal control of helicopters, the control procedures following power failure were theoretically investigated by applying nonlinear optimal control theory to the following four optimization problems. The first was minimization of the touchdown speed following power failure. Comparisons between the calculated optimal solutions and the empirical flight test results showed that pilots used nonoptimal controls, especially in the timing and amplitude of the collective flare before touchdowns. The second was prediction of the height-velocity (H-V) boundaries. The calculated H-V boundaries showed good correlation with the flight test results. The third was optimization of the takeoff procedures for category A STOL operation following power failure. The results showed that the required takeoff distance using the normal takeoff procedure can be significantly reduced. The fourth was evaluation of the takeoff performance for category A VTOL operation. The calculating method of the maximum takeoff weight was confirmed, and possibility of allowing the payload to be increased was shown. 38 refs., 53 figs.

  5. Vibration control of bridges and buildings hybrid system. Kyoryoter dot tatemono no shindo seigyo hybrid hoshiki

    Energy Technology Data Exchange (ETDEWEB)

    Tanida, K. (Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan))

    1991-11-15

    Multistory buildings, suspension bridges, and cable stayed bridges tend to become huge, and technology of controlling their vibration caused by strong winds and earthquakes is becoming an important subject for study. A description is made on a hybrid system which is a combination of the conventional passive system and active system, having merits of both of the systems. Verification test made using a model and an example of application to an actual bridge are introduced. This hybrid control system has been applied to the main tower of the cable stayed bridge on Route 12 of the Tokyo expressway. It is installed and in operation on the top of the tower to improve the workability, and can decrease the vibration of the tower caused by vortical excitation produced during the construction of the main tower. With the hybrid system, the actuator capacity can be reduced to about 1/5 for the similar damping performance to that of the active system with the same mass ratio. In addition, the weight of the equipment can be nearly halved in comparison with the passive system. Moreover, it has such a high safety characteristic as being used as a passive system when power supply is cut off because the controlling force of the system is smaller as compared with the active system. 2 refs., 11 figs.

  6. Organic materials for semiconductor. Epoxy molding compound for IC encapsulation; Handotai kanren no yuki zairyo. Handotai fushiyo epoxy seikei zairyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kusuhara, A. [Sumitomo Bakelite Co. Ltd., Tokyo (Japan)

    1998-11-05

    This paper describes organic materials for semiconductor. Based on the composition and raw material, typical materials are epoxy resins, curing agents including phenol-novolak resins, fillers including silica and alumina, flame retardants including brominated epoxy resin and antimony oxide, hardening accelerators including amine compounds and phosphorus compounds, coupling agents including silane compounds and titanate compounds, and the others including colorants and mold lubricants. Raw materials are heated and kneaded after mixing, and produced as tablets after cooling and crushing. Recently, the packages have changed from insertion type to surface mounting type for the small thin IC package and for improving the efficiency of soldering during the incorporation of IC package on the print circuit substrate. High temperature of 260degC has been employed from the conventional limit of 100degC. Reduction of water absorption, improvement of adhesion, reduction of thermal expansion coefficient, and reduction of elastic modulus during heating are promoted for avoiding the peeling and cracking due to the sudden evaporation of adsorbed moisture. This paper also describes the organic materials for BGA. 10 figs., 4 tabs.

  7. Introductory asphalt technology; Nyumon asphalt gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Muroga, G. [Mitsubishi Oil Co. Ltd., Tokyo (Japan)

    1994-12-28

    The type and applications, manufacturing method, characteristics, road pavement etc. of asphalt were introduced. Among the petroleum asphalts, straight asphalt is used for road pavement,industry, and combustion, while blown asphalt is mainly used for the waterproofness of a building. Also, the demand for modified asphalt where rubber or thermoplastic elastomer was mixed is increasing. Straight asphalt is obtained by allowing atmospheric distillation tower bottom oil to be subjected to reduced pressure distillation and drawing reduced pressure gas oil and lubrication oil cut. Blown asphalt is produced by the oxidation dehydrogeneration and condensation polymerization reaction of soft straight asphalt. Rheology characteristics of asphalt are expressed by stiffness, relaxation elastic modulus, complex elastic modulus, etc. Also, asphalt has high electrical dielectric properties. Asphalt pavement has functions for dispersing traffic load and then transferring it to a lower layer, for resisting wear and cracking, and for preventing penetration of rainwater. 30 refs., 5 figs., 4 tabs.

  8. Surface modification of biocompatible materials. Seitai tekigo zairyo no hyomen kaishitsu

    Energy Technology Data Exchange (ETDEWEB)

    Tateishi, T [Mechanical Engineering Lab., Tsukuba, Ibaraki (Japan)

    1993-07-05

    The necessary conditions for biocompatible materials such as human bone, joints and teeth are mainly classified into biological condition and mechanical conditions. The former condition is consisted of chemical stability without causing poisoning or allergy, compatibility of good biological tissue, no carcinogenesis and not antigenicity, no decomposition and degradation inside human body, not causing adsorbate or precipitate. As for the latter, appropriate static strength, elastic modulus and hardness together with the characteristics like fatigue resistance, wear resistance and lubricating properties are given. As for other conditions for biomaterials, characteristics as a functional material, workability, adhesion and so forth are important. When surface nitrification of sintered Ti, forging Ti, sintered Ti-6Al-4V and forging Ti-6Al-4V is carried out, the solubility is decreased significantly by surface nitrification. The powder generated by the wear of nitriding Ti-6Al-4V with ultra high molecular weight polyethylene (UHMWPE) is less cell poisoning than the powder caused by the wear of the other alumina, stabilized zirconia, hydroxy apatite with UHMWPE. 16 refs., 2 figs., 1 tab.

  9. Research study on highly functional carbon related materials; Tansokei kokino zairyo no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The study results on highly functional carbon related materials are reported as a part of the leading research in fiscal 1996. Synthesis of these novel materials is outlined, and R & D results on the following materials are described: diamond, hetero-diamond, graphite, amorphous carbon, carbyne, fullerences, carbon nitride and chemically modified carbon materials. Their issues, future possibility and market in 2010 are also described. The markets are predicted of such electronic materials as electronic emitter, sensor, solid device and heat sink, such optical materials as X-ray lithography, and such chemical materials as electrode and catalyst. Promising characteristics of light-weight and high-hardness machine materials are presented, and some issues such as material synthesis, and intensive machining and application technologies are described. The future markets are predicted of their applications to tools, dies, information equipment, glass, automobiles, aircraft, spacecraft and industrial machines. Problems and their break through techniques of these novel materials are also presented. 220 refs., 68 figs., 16 tabs.

  10. FY 1993 report on the Material Committee; 1993 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper reported the FY 1993 activities of the Material Committee on the R and D of materials in coal liquefaction, coal gasification, coal utilization hydrogen production, etc. As to metal materials, a PSU implant test on 3Cr-1Mo base high-strength steel was conducted to examine mainly the hydrogen erosion resistance. Concerning surface coatings, aiming at improving the sulfuration corrosion resistance of Al{sub 2}O{sub 3} atmospheric plasma spraying materials, survey of the deterioration with age was made by inserting a test piece in which the structure of coated bed was altered into the PSU reaction tower. Relating to the R and D of trial manufacture of plant use equipment materials, study was made of the evaluation of characteristics of materials for improvement/trial manufacture of gasifier use refractory and the effect of improvement in erosion by coarsening treatment of mullite ceramics. As to the development of the control valve, etc., the control valve was manufactured using sintering diamond as sheet ring material and wolfram carbide as plug material, and the demonstrative test under the actual environment in PSU was carried out. The demonstrative test was also made on slurry flow meter and block valve. (NEDO)

  11. Investigation research on autonomous responsive materials; Jiritsu oto zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was made on autonomous responsive materials as a new material which reversibly change molecular structures and the aggregation state according to external stimuli. Autonomous responsive materials imitate environmental responsibility in the living organism system and have sensing, control and active functions for external stimuli. The materials are highly efficient and environmentally friendly. In biomimetic materials for soft actuators, drastic changes by temperature of elastic modulus of water-swollen hydrogel are used to the motion. In order to molecularly design stimulus-responsible polymer gel, studied are the relation between the micro structure and stimulus responsibility, dynamic correlation between the micro structure and the macro structure, etc. In the biomedical field, new cure and diagnosis using innovative materials are expected, and the application of autonomous responsive materials to the field is studied. For example, using hydrogel responding the temperature and the surface and controlling by temperature the interaction with components of the organism such as protein and cells, drug delivery in the organism is optimized. Also studied is the application of hydrophilic/hydrophobic changes by temperature to the chromatography. 215 refs., 47 figs., 11 tabs.

  12. Ferroelectric materials for FeRAMs; FeRAM yo kyoyudentai zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Miyasaka, Y [NEC Corp., Tokyo (Japan)

    1998-10-01

    Studies to utilize bistable spontaneous polarization of ferroelectric materials for non-volatile memory have already been started in the 1950`s. Recently, a possibility was indicated on a high-speed non-volatile RAM (FeRAM) with memory cell configuration combined with switching transistors as in DRAMs. This situation has led to performing very active studies on ferroelectric materials and electrode materials used in ferroelectric film cell capacitors. This paper summarizes the above research and development circumstances, as well as their future problems. On the other hand of having shown excellent fatigue resistance in the SrBi2Ta209(SBT) system, improvement has progressed steadily on the Pb(ZR, Ti)03 (abbreviated to PZT) system, which retains the mainstream position as the ferroelectric material for FeRAMs. Aiming at realizing a high integration FeRAM in the future will require discussions on property changes due to use of lower temperature and micronization in film formation, further improvement in relation with degradation such as in imprint, and elucidation of the mechanism. 31 refs., 3 figs.

  13. Self-repairing of material damage. Sonsho wo jiko shufuku yokushisuru zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, S [National Research Inst. for Metals, Tsukuba (Japan)

    1994-07-01

    In order to control the damage like crack or void formed during the use of structural material by the material itself, it is required to self-detect the damage, to self-judge the state of damage, and to self-control or self-repair the damage finally. Based on the parameter of length, the repair and control is classified into the 1mm-scale functional fine wire and thin film utilization type, 1[mu]m-scale microcapsule type, and 1nm-scale trace element utilization type. For the damage repair and control of functional fine wire and thin film utilization type, the damage is repaired and controlled by pasting thin film or by embedding fine wire of functional material, such as shape memory alloy, Ti-Ni, and piezoelectric ceramics PZT (lead zirconate titanate), on the material surface or inside the material. For the damage repair and control of microcapsule type, is illustrated the control mechanism of high temperature fatigue crack propagation by Y2O3 particles dispersed in the Fe-20Cr alloy. Furthermore, the formation mechanism of self-repairing film by the trace element is also illustrated. 13 refs., 5 figs.

  14. Advanced materials for aircraft engine applications. Koku engine yo zairyo no doko

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    The thrust/weight ratio which is thrust per unit weight of engine is a parameter of aircraft engine performance. With a mean material density of 6.6g/cm[sup 3], some of the supersonic plane engines are 7.9 in thrust/weight ratio. Its attaining 20 is predicted by some reports. The turbine inlet temperature is a parameter of engine temperature heightening exceeds 1400[degree]C. Its attaining 2000[degree]C in the 21st century is also predicted by some reports. By dividing the aircraft engine materials into both improvement and innovation material systems, the present paper explained the characteristics and present status of materials, and how to put them in practical use. As an improvement material, titanium alloy, nickel base alloy and resinous composite materials were exhibited with examples of having improved the established material system in performance and cost. Used as a turbine vane member, the nickel base alloy contributes, as a unidirectional coagulation alloy, single crystal alloy and oxide dispersion exciting alloy, to the creep resistance strengthening at high temperatures against the fatigue due to thermal strain. It is also explained how to put TiAl and FRM to practical use. 8 refs., 13 figs., 2 tabs.

  15. Materials and joining technologies of commercial jet plane. Jet ryokyakuki ni okeru zairyo to setsugo

    Energy Technology Data Exchange (ETDEWEB)

    Hira, H; Yoshino, Y [Kawasaki Heavy Industries,Ltd., Tokyo (Japan)

    1993-12-05

    The present report explained light weight and high strength materials which are strong against the corrosion and fatigue, and economical. Also explained were their joining technologies for the commercial jet plane production. Resin composites are acceleratedly used as light weight and high strength materials. Fiber to be used is heightened in strength by replacing the glassfiber by the hybrid and carbon fiber. As measures against the drop in both strength around the drilled holes, and compressive strength due to the separation between layers and dehumidification, which drop is a defect generated in the composite, improving measures are taken such as enlargement of allowable strain by carbon fiber of a medium elastic modulus, use of resin base hardly degraded by the dehumidification and diffusion of high toughness resin. Metallic materials are also heightened in characteristics. For the joining technologies, measures are progressively taken against the strength damage around the drilled holes and electric corrosion by fasteners in the composite. Also for the tightening of metallic materials, the fatigue strength is designed to be heightened by the introduction of compressive residual stress. Both thermal degradation and stress in the hardening process must be taken into consideration for the structure use adhesives which are mainly of an epoxy system. The corrosion control is indispensable at the time of etching for the metallic adhesion. The welding was also explained. 16 refs., 7 figs., 2 tabs.

  16. Weight reduction of vehicles and light metals; Jidosya no keryoka to keikinzoku zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Manabe, Akira. [Toyota Motor Corp., Aichi (Japan). Component and System Development Center

    1999-08-15

    Weight reduction of vehicles (WRV) is a continuous challenge from the beginning of the vehicle history, however the purpose of WRV has been changing by social requirements. Recently automotive industry is facing is facing with the global warmin and the other environmental issues, so we are vast amount of R and D resources to improve the fuel economy. In this paper, the changes of the purpose of WRV and, the relation between fuel economy and WRV, are summarized. And also the current status of light metals usage and the future work for the related material issues, in particuar the corrosion resistance, are brifly mentioned. (author)

  17. Report on the material committee meetings in fiscal 1987; 1987 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The material committee has held two meetings in this fiscal year. The first committee meeting (September 25, 1987) was held for the major agenda of (1) the development of a centrifugal slurry pump for liquefaction plants, and as the research and development in fiscal 1987, the in-plant tests on new materials and the development a let-down valve, which were reported and deliberated. The major agenda of the second committee meeting (February 24, 1988) were, as the summarized achievements in fiscal 1987, (2) development of a technology to manufacture hydrogen by utilizing coal, (3) in-plant tests on new materials, and (4) development of a let-down valve, which were reported and deliberated. In Item (1), wear in the shaft seal of the centrifugal slurry pump was discussed regarding its cause from the result of a contraction flow test. In Item (2), it was verified that picrochloromite and chromia are integrated as an electromelting aggregate for the atmospheric stability of refractories used in a gasification furnace, and that the test conditions for the refractories call for the refractories to be tested under severe conditions. In Item (3), how to proceed the tests in the future was verified on such items as corrosion patterns, tested materials, coal types, and the degree of corrosion. In Item (4), kinds and temperatures were verified on slurries used in the water-slurry wear test and the fretting corrosion test. (NEDO)

  18. Structural experiment of wind turbine blades; Fushayo blade no zairyo rikigakuteki jikken kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Seki, K; Shimizu, Y; Kuroyanagi, H [Tokai University, Tokyo (Japan)

    1997-11-25

    Aluminum, GFRP and composite of aluminum coated with carbon as structural materials for wind turbine blades were bending-tested, to improve blade bending stiffness, understand stress conditions at each position, and clarify structural dynamic strength by the bending-failure test. It is possible to estimate stress conditions at each position from the test results of displacement and strain at each load. The test results with GFRP are well explained qualitatively by the boundary theory, known as a theory for composite materials. The test gives reasonable material strength data, useful for designing wind turbines of high functions and safety. The results of the blade bending-failure test are in good agreement with the calculated structural blade strength. It is also found that GFRP is a good material of high structural strength for wind turbines. 8 refs., 6 tabs.

  19. Globalization of Japanese steel industry. Part 1. Materials; Tekkogyo no kokusaika. 1. Zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Aramaki, T. [Nippon Steel Corp., Tokyo (Japan)

    1995-01-01

    This paper discusses the globalization of the Japanese steel industry from the viewpoint of maintenance of international competitive potential. In the steel industry, remarkable technology innovation is currently occurring in the production process. The direct iron ore smelting process and strip caster process are being developed. These innovative technologies are characterized by processes having simplified facilities and lower fixed costs. A large problem of Japanese steel industry is the maintenance of competitive potential in the international price. For the purpose of the cost reduction, profitability improvement efforts have been made, as for the cut of research and development cost, consolidation of standards, intensive production, specialization among undertakings, cooperations, etc. Additionally, accompanied with the overseas production of steel consumers, the overseas steel production has been conducted. The overseas production is currently focused on Asia. Significance of the Japanese steel industry in Asia is provided from the viewpoint of accumulating technological know-how, establishment of new technologies, acquisition of operation technologies, promotion of talented persons for industries, etc. 12 refs., 7 figs., 3 tabs.

  20. FY 1990 report on the Material Committee; 1990 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The paper reported the FY 1990 activities of the Material Committee on the R and D of materials in coal liquefaction, coal gasification, coal utilization hydrogen production, etc. As to the development/assessment of new materials for plant use, the sulfuration corrosion resistance was confirmed of aluminum diffusion coated agent and aluminized materials. Further, in the measurement of hydrogen permeability of the test piece exposed for 500 hours to the sulfuration corrosion environment, a good hydrogen permeation control effect was confirmed of hot-dipped materials and SiC/TiC plasma CVD materials. As to the development of the control valve, etc., CVD coating of Ti (C, N) and sintering diamond indicated good erosion resistance in the high speed water slurry injection test. Further, in the high speed powder injection test, PVD coating of TiN and sintering diamond indicated good erosion resistance. As to the development of the coal utilization hydrogen production technology, the following were carried out: improvement of gasifier use materials, assessment of materials under the corrosive environment where coal slag exists, experimental study on the repair technology, etc. (NEDO)

  1. Research on harmonized molecular materials; Bunshi kyocho zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Harmonized molecular materials (HMM) were researched to create functional materials adaptable to needs such as environmental harmony and high-efficient conversion in post-industrial society and aging society. Superior mechanisms function efficiently in organisms for perception, transmission and processing of information, and transport and conversion of substances. These functions are caused by harmonization between organic molecules, or organic molecule and metal or inorganic substance. HMM is a key substance to realize these functions similar to those of organisms artificially. It is the purpose of this research to develop HMMs, reform production process by innovating separation and conversion technologies, and finally realize molecular chemical plants. This research also develops high-efficient devices to contribute to the information society, and progresses the industry of bio-functional materials such as high-sensitive bio-sensor. The functions, applications and creation technologies of three kinds of HMM such as assembly, mesophase and microporous materials were researched in fiscal 1995. 956 refs., 128 figs., 13 tabs.

  2. Research study on harmonized molecular materials (HMM); Bunshi kyocho zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As functional material to satisfy various needs for environmental harmonization and efficient conversion for information-oriented and aging societies, HMM were surveyed. Living bodies effectively carry out transmission/processing of information, and transport/conversion of substances, and these functions are based on harmonization between organic molecules, and between those and metal or inorganic ones. HMM is a key substance to artificially realize these bio-related functions. Its R & D aims at (1) Making a breakthrough in production process based on innovation of material separation/conversion technology, (2) Contribution to an information-oriented society by high-efficiency devices, and (3) Growth of a functional bio-material industry. HMM is classified into three categories: (1) Assembly materials such as organic ultra-thin films (LB film, self-organizing film), and organic/inorganic hybrid materials for optoelectronics, sensors and devices, (2) Mesophase materials such as functional separation membrane and photo-conductive material, and (3) Microporous materials such as synthetic catalyst using guest/host materials. 571 refs., 88 figs., 21 tabs.

  3. Investigational research on the design of computational materials; Keisanki zairyo sekkei no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Computer chemistry was investigationally studied. The advance of theoretical chemistry is indispensable to the design of materials, and the theory and high speed computational method are expected which can simulate the real system with more accuracy. It is basic to simulate structures and physical properties of structural molecules and the aggregate, but the meso region, the intermedium region between structural molecules and the aggregate, has became regarded as important. Rough visualization models in high polymer materials and the progress of computational software/hardware of quantum chemistry/molecular dynamics such as catalyst become necessary. Seamless zooming is proposed as a concept of the software which simulates materials from micro/macro/meso viewpoints. Moreover, to make the most of computer chemistry, an integrated system is necessary which generally handles computational software, database, etc. For the development of software, indispensable is the demonstrative verification by a combination of experiments and researchers. Under a commission from NEDO, the investigational research was conducted as a leading study during fiscal 1996 and 1997 to view the course of the research. 17 refs., 37 figs., 5 tabs.

  4. Molding compound development with semiconductor PKGs; Handotai PKG doko to fushi jushi zairyo

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, I. [NEC Corp., Tokyo (Japan)

    1998-11-05

    This paper describes the semiconductor packaging and molding compound materials. Major constituents of the molding resins are epoxy resin and inorganic silica, to which various additives are added. In order to make thin packages, biphenyl-based resins with low viscosity are often used in response to high fluidity. To fill the clearance less than 100 {mu}m, size adjusting techniques of the inorganic silica are also significant apart from resins. Since it is heated under the water absorption condition for the packaging in substrates, low water absorption, high adhesion, high strength and low stress are required to avoid peeling and cracking due to the vapor pressure of moisture. Generation of voids is also a problem. Improvement of productivity by reducing the processing period is also significant. In response to the strict environmental regulation, disuse of brominated epoxy and antimony oxide which are flame retardants in the molding resins is an urgent problem to be solved. For the epoxy resins, bisphenol A is to be regulated as a mutation substance. The cost reduction is required with keeping current quality kept. 1 fig.

  5. Survey and research on precision polymerization polymeric materials; Seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey and research on the precision control of primary structure of polymeric materials and the precision evaluation technology have been conducted to develop advanced polymeric materials. It is proposed that the three basic processes of polymer synthesis, i.e., addition, condensation, and biomimesis, in forming the precision polymerization skeleton are to be covered through a centralized joint research effort with participation of industry, academia, and the government institute and under the leadership of researchers from academic institutions as the team leaders. For the study of technology trends, international conferences held in UK, Germany, and Hawaii are introduced, and domestic meetings, i.e., Annual Polymer Congress and Polymer Conference, are summarized. In addition, Precision Polymerization Forum and International Workshop on Precision Polymerization were held. The basic studies include a quantum-chemical elucidation of the elementary process in polymerization reaction, time-resolved analysis of polymerization process and polymer properties, synthesis of polymers with controlled microstructures by coordination polymerization using metal complexes, synthesis of polymer with controlled microstructures by precision polycondensation, molecular recognition in catalyst-reaction site, and synthesis of imprinting polymers. 246 refs., 117 figs., 14 tabs.

  6. Assessment report on the development of functionally inclined material; Keisha kinosei zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning a project whose aim is to develop heat resistant engine members through the application of the concept of functionally inclined materials, deliberation and assessment are made of the meaning of its implementation, validity of the research program, research achievement, etc. The project deals with a specimen, diameter 150mm or more and thickness 5mm or more, built of a zirconia/stainless steel-based functionally inclined material, and its goal is to develop technologies for optimizing the baking process for the said specimen, baking system and related devices, assessment technique, tribological assessment technique, etc., and it is inferred that these targets are reasonable. As the result of this research, an energy-efficient (power consumption reduced to 1/3 to 1/5) practical rapid sintering system is constructed. Basic data are collected relative to the tribology of the functionally inclined material, and it is proved that it is feasible to use the material for engine members. The process technology, assessment technology, and devices developed under this project are the first in the world, and are highly evaluated. (NEDO)

  7. Report on the material committee in fiscal 1988; 1989 nendo zairyo iinkai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    This paper describes a report on the material committee for coal gasification technology development in fiscal 1988. The in-plant test on new materials has performed information investigation on use characteristics and use records of new materials. A sulfurizing corrosion resistance test showed that the aluminum-chromium diffused and permeated material and the molten aluminum plated material stabilize the coated surface and have high corrosion resistance. Ceramics painted lining material was evaluated unusable in a steam diffusion test. Phenol resin was found sufficiently usable as a result of giving the stress test at 100 to 150 degrees C. In developing a let-down valve, a high-velocity water slurry injection test revealed that CVD coating of Ti (C, N) has high effect of suppressing the erosion damage. In a high-velocity powder injection test, PVD coating of TiN and CVD coating of TiC were found to show good erosion resistance. Tests and researches were performed to evaluate durability of furnace materials for manufacturing gasified hydrogen, and elucidate conditions to cause iron oxide burst. Evaluation on repairing techniques, and improvement on durability were also executed. (NEDO)

  8. Utilization of new materials in prestressed concrete. Shin zairyo no puresutoresuto concrete eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Imai, Y. (Taisei Corp., Tokyo (Japan)); Kato, H. (Building Research Inst., Tokyo (Japan)); Mutsuyoshi, H. (Saitama Univ., Urawa (Japan). Faculty of Engineering)

    1994-03-31

    In this session for the new materials, almost all of them were the presentation on the fiber reinforced plastics (FRP). Based on these facts, the topics of new materials about PC centered around FRP, and consequently it was found that how it was expected as the new materials and how it is being watched with keen interest. Even in FRP, the presentations on the carbon fiber reinforced plastics (CFRP) and aramid fiber reinforced plastics (AFRP) were a little bit more than those on the glass fiber reinforced plastics (GFRP), and therefore they were felt to be predominant. Although the ones about a fundamental study on the material characters of FRP held approximately 70%, as a content, there were 6 presentations on the design and execution of the actual bridges in which FRP was used for the PC take-up materials and the oblique cable of cable-stayed bridges, consequently it was found that FRP did not stay at a study stage, and was already shifting to the actual application stage. However, at the current situation, there were many of experimental ones like the small scale bridges in the golf courses, and furthermore it can not be said that a guideline for the design and execution is sufficiently established. 2 figs.

  9. FY1995 molecular control technology for mining of methane-gas-hydrate; 1995 nendo methane hydrate no bunshi seigyo mining

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The objectives of the investigation are as follows: 1) developing a method to control formation/dissociation of methane-gas-hydrate, 2) developing a technology to displace methane gas by CO{sub 2} in methane-gas-hydrate deposit, 3) developing a technology to produce methane gas from the deposit efficiently. The final purpose of the project is to create new mining industry that solves both the problems of energy and global environment. 1) Clustering of water molecules is found to play the key role in the methane gas hydrate formation. 2) Equilibrium properties and kinetics of gas hydrates formation and dissociation in bulk-scale gas-hydrate are clarified in the practical environmental conditions. 3) Particle size of hydrate deposit influences the formation and dissociation of bulk-scale gas-hydrate crystal. 4) Mass transfer between gas and liquid phase in turbulent bubbly flow is a function of bubble diameter. The mass transfer depends on interfacial dynamics. (NEDO)

  10. Autonomous navigation of the vehicle with vision system. Vision system wo motsu sharyo no jiritsu soko seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Yatabe, T.; Hirose, T.; Tsugawa, S. (Mechanical Engineering Laboratory, Tsukuba (Japan))

    1991-11-10

    As part of the automatic driving system researches, a pilot driverless automobile was built and discussed, which is equipped with obstacle detection and automatic navigating functions without depending on ground facilities including guiding cables. A small car was mounted with a vision system to recognize obstacles three-dimensionally by means of two TV cameras, and a dead reckoning system to calculate the car position and direction from speeds of the rear wheels on a real time basis. The control algorithm, which recognizes obstacles and road range on the vision and drives the car automatically, uses a table-look-up method that retrieves a table stored with the necessary driving amount based on data from the vision system. The steering uses the target point following method algorithm provided that the has a map. As a result of driving tests, useful knowledges were obtained that the system meets the basic functions, but needs a few improvements because of it being an open loop. 36 refs., 22 figs., 2 tabs.

  11. Simulation of speed control in acceleration mode of a heavy duty vehicle; Ogatasha no kasokuji ni okeru shasoku seigyo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Endo, S; Ukawa, H [Isuzu Advanced Engineering Center, Ltd., Tokyo (Japan); Sanada, K; Kitagawa, A [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    A control law of speed of a heavy duty vehicle in acceleration mode is presented, which is an extended version of a control law in deceleration mode proposed by the authors. The control law is based on constant acceleration strategy. Using the control law, target velocity and target distance can be performed. Both control laws for acceleration and deceleration mode can be represented by a unified mathematical formulae. Some simulation results are shown to demonstrate the control performance. 7 refs., 9 figs., 2 tabs.

  12. Optimum differential terms for lateral motion control performance on the vehicle; Yokoundo seigyo seino ni oyobosu hisenkei bibunko no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Miyamori, A [Japan Consumer Information Center, Tokyo (Japan); Nakaya, H [Shibaura Institute of Technology, Tokyo (Japan)

    1997-10-01

    As general knowledge, the lateral control performance of vehicle improves as differential terms increases. But subjective rating has its limits of effect. The coefficient of differential terms and saturated steer angle velocity were set up using the experimental vehicle in several steps. Consequently, the optimum range, that subjective and objective rating were compatible, were made clear. 4 refs., 6 figs., 1 tab.

  13. Next generation railway system. ; Control system for JR Maglev. Jisedai tetsudo system. ; Rinia shinkansen no seigyo system

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, K [Central Japan Railway Company, Nagoya (Japan)

    1993-07-10

    Aiming at achieving a maglev Shinkansen that links Tokyo with Osaka at a speed of 500 km/h, an experimental maglev line is being constructed in Yamanashi Prefecture. This paper explains a train control system as the main subject. The system mounts superconductive magnets directly on bogies to propel a train using actions of moving magnet fields generated from propulsion coils paved on ground. Because of its mechanism to levitate and guide the train using induction coils superposed on the propulsion coils, no special control device is required for the levitation and guidance. This is a difference from a normal conduction magnet levitation system. Its speed control also differs from the conventional railway systems. It uses a ground primary control system that controls supply currents from substations on the ground, including braking control. One substation controls one train only. Automatic control is made on all controls related to travelling, including a control from train movement start to stops at predetermined positions, scheduled-time operation control, and jerk control. The construction of the experimental line is under steady progress. 5 figs.

  14. Design and model experiments on thruster assisted mooring system; Futaishiki kaiyo kozobutsu no thruster ni yoru choshuki doyo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M; Koterayama, W [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Kajiwara, H [Kyushu Institute of Technology, Kitakyushu (Japan). Faculty of Computer Science and System Engineering; Hyakudome, T [Kyushu University, Fukuoka (Japan)

    1997-12-31

    Described herein are dynamics and model experiments of the system in which positioning of a floating marine structure by mooring is combined with thruster-controlled positioning. Coefficients of dynamic forces acting on a floating structure model are determined experimentally and by the three-dimensional singularity distribution method, and the controller is designed by the PID, LQI and H{infinity} control theories. A model having a scale ratio of 1/100 was used for the experiments, where 2 thrusters were arranged in a diagonal line, one on the X-axis. It is found that the LQI and H{infinity} controllers of the thruster can control long-cycle rolling of the floating structure. They allow thruster control which is insensitive to wave cycle motion, and efficiently reduce positioning energy. The H{infinity} control regulates frequency characteristics of a closed loop more finely than the LQI control, and exhibits better controllability. 25 refs., 25 figs.

  15. Formal verfication of a railway crossing controller using time petri nets; Taimupetorinetto wo mochiita fumikiri seigyo puroguramu no keishikiteki kensho

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, R. [The Nippon Signal Co. Ltd., Tokyo (Japan); Yoneda, T. [Tokyo Inst. of Technology, Tokyo (Japan)

    1994-12-20

    In the system requesting the real-time property, detecting the dugs in the method by carrying out the verification at the stage of method is important for excluding the error from the latter process. The verifying device for investigating whether the properties are satisfied by the system with the expression of the operation rules of system with time Petri nets and presenting the properties to be verified with real-time linear time-phase theory is developed by Yoneda, et al. In this paper, the verification of train check and warning-controlling operation in railway-crossing is carried out by using said verifying device, and the effectiveness of this verifying method is examined. In the practical controlling program, the mistakes in design occurs easily because of the further execution of complex processings including the countermeasure to the defect of short circuit in controlling unit and the control of up/down trains. It is planned in the future to modeled such processings as well as functions and to verify the system more utilizable. 12 refs., 11 figs., 1 tab.

  16. Design and model experiments on thruster assisted mooring system; Futaishiki kaiyo kozobutsu no thruster ni yoru choshuki doyo seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M.; Koterayama, W. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Kajiwara, H. [Kyushu Institute of Technology, Kitakyushu (Japan). Faculty of Computer Science and System Engineering; Hyakudome, T. [Kyushu University, Fukuoka (Japan)

    1996-12-31

    Described herein are dynamics and model experiments of the system in which positioning of a floating marine structure by mooring is combined with thruster-controlled positioning. Coefficients of dynamic forces acting on a floating structure model are determined experimentally and by the three-dimensional singularity distribution method, and the controller is designed by the PID, LQI and H{infinity} control theories. A model having a scale ratio of 1/100 was used for the experiments, where 2 thrusters were arranged in a diagonal line, one on the X-axis. It is found that the LQI and H{infinity} controllers of the thruster can control long-cycle rolling of the floating structure. They allow thruster control which is insensitive to wave cycle motion, and efficiently reduce positioning energy. The H{infinity} control regulates frequency characteristics of a closed loop more finely than the LQI control, and exhibits better controllability. 25 refs., 25 figs.

  17. Research on crystal growth by using pressure as a control parameter; Atsuryoku seigyo ni yoru kessho seicho ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-31

    This research project aims to establish a technique for crystal growth using pressure as a principal control parameter, and combining it with a microgravity condition, to develop a novel process material fabrication. Since the solubility of materials depends on pressure, it is possible to control a supersaturated condition for crystal growth by changing pressure. The growth condition can be controlled precisely, which is not possible by conventional methods that vary temperature and other factors. On the other hand, because a concentration diffusing field is formed autonomically around crystals in association with their growth, density convection is generated under gravity as a result of difference in the concentrations, making the growth conditions severely complex and uncontrollable. Ideal crystal growth condition control may be possible if the pressure control is performed under micro-gravity by which generation of the density convection can be suppressed. Realization has been achieved on in-situ observation by using high-magnification microscope which uses a diamond anvil cell, development of a hydraulic type optic pressure cell, and a high- speed crystal growing technology by means of pressure control utilizing the cell. New findings were also obtained on effects of pressure on crystal forms, and the pressure induced solid phase transfer mechanism. 67 refs., 49 figs., 3 tabs.

  18. Study of design factors of vehicle headlamp control systems; Zenshoto seigyo system no hyoka shuho no kento

    Energy Technology Data Exchange (ETDEWEB)

    Kamishima, H; Miwa, T; Sasaki, T; Imai, M [Nissan Motor Co. Ltd., Tokyo (Japan); Sumi, T [Niles Parts Co. Ltd., Tokyo (Japan)

    1997-10-01

    The on-and-off timing of vehicle headlamp control systems varies with weather conditions. Cloudy weather has a wider light energy distribution from visible to infrared radiation than clear weather. Silicon photodiodes, which can detect visible to infrared radiation, have larger output currents on cloudy evenings than on clear evenings under the same brightness conditions. The systems should be designed with such factors in mind as spectral characteristics of windshield, filters, sensor, and eyesight. 4 refs., 9 figs.

  19. Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakatani, T. [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K.; Moriyoshi, N. [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T. [Nagoya Institute of Technology, Nagoya (Japan)

    1996-12-31

    Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

  20. Consideration on local blast vibration control by delay blasting; Danpatsu happa ni yoru kyokuchiteki shindo seigyo ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Mogi, Gento; Adachi, Tsuyoshi; Yamatomi, Jiro [The University of Tokyo School of Engineering Department of Geosystem Engineering, Tokyo (Japan); Hoshino, Tatsuya [Mitsui Mining and Smelting Corp., Tokyo (Japan)

    1999-10-31

    In this research, local blast vibration control based on the theory of superposition of waves was investigated. Firstly, the influence of delay time errors of conventional electric detonators upon the level of local blast vibration was examined. Secondly, for a further effective local blast vibration control, a new delay blasting design concept 'combined delay blasting' that postulates the use of electronic detonators, which virtually have no delay time errors, is proposed. For a delay blasting with uniform detonation time intervals, an optimum time interval to minimize the local PPV (Peak Particle Velocity) is obtained based on the relationship between the PPV and the time interval, which is derived by superposing identical vibration time histories of each single hole shot. However, due to the scattering of the actual delay time caused by errors, PPV of a production blast seldom coincides with the estimated one. Since the expected value and the variance of PPV mainly depend on sensitivity of PPV around the nominal delay time, it is proposed that not only the optimum but also several sub-optimum candidates of delay time should be examined taking error into consideration. Concerning the 'combined delay blasting', its concept and some simulation results are presented. The estimated reduction effect of blast vibration of a delay blast based on this concept was quite favorable, indicating a possibility for further effective local blast vibration control. (author)

  1. Study on molecular controlled mining system of methane hydrate; Methane hydrate no bunshi seigyo mining ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kuriyagawa, M; Saito, T; Kobayashi, H; Karasawa, H; Kiyono, F; Nagaoki, R; Yamamoto, Y; Komai, T; Haneda, H; Takahashi, Y [National Institute for Resources and Environment, Tsukuba (Japan); Nada, H [Science and Technology Agency, Tokyo (Japan)

    1997-02-01

    Basic studies are conducted for the collection of methane from the methane hydrate that exists at levels deeper than 500m in the sea. The relationship between the hydrate generation mechanism and water cluster structure is examined by use of mass spectronomy. It is found that, among the stable liquid phase clusters, the (H2O)21H{sup +} cluster is the most stable. Stable hydrate clusters are in presence in quantities, and participate in the formation of hydrate crystal nuclei. For the elucidation of the nucleus formation mechanism, a kinetic simulation is conducted of molecules in the cohesion system consisting of water and methane molecules. Water molecules that array near methane molecules at the normal pressure is disarrayed under a higher pressure for rearray into a hydrate structure. Hydrate formation and breakdown in the three-phase equilibrium state of H2O, CH4, and CO2 at a low temperature and high pressure are tested, which discloses that supercooling is required for formation, that it is possible to extract CH4 first for replacement by guest molecule CO2 since CO2 is stabler than CH4 at a lower pressure or higher temperature, and that formation is easier to take place when the grain diameter is larger at the formation point since larger grain diameters result in a higher formation temperature. 3 figs.

  2. Robust control system for belt continuously variable transmission; Robust seigyo wo tekiyoshita mudan hensokuki no hensokuhi servo kei no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, K; Wakahara, T; Shimanaka, S; Yamamoto, M; Oshidari, T [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The continuously variable transmission control system consists of generation of a desired gear ratio and a servo gear ratio system. The servo gear ratio system must provide the desired response at all times without being influenced by external disturbances. These include oil pressure as well as variation in performance due to operating conditions or changes occurring with us. We have developed the servo gear ratio system incorporating a robust model matching method, which enables the belt continuously variable transmission to satisfy this performance requirement. 2 refs., 9 figs.

  3. Shift operation control of automatic transmission by {mu}-synthesis; {mu} synthesis ni yoru jido hensokuki no hensoku seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Nagaoka, M; Nishiyama, Y; Nakayama, Y; Kamada, S [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We have developed a control technology, which the robust control theory is applied, to improve a shift quality of automatic transmission for a passenger car. When applying the robust control theory to the transmission control, many issue arise such as difficulty in system identification and/or the capability of ECU for computing. Recently, We have obtained an exact performance that allows the transmission to be robust controlled with an onboard ECU by improving the system identification process and reducing the model dimensions after the controller design finalized. 6 refs., 7 figs.

  4. Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakatani, T [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K; Moriyoshi, N [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T [Nagoya Institute of Technology, Nagoya (Japan)

    1997-12-31

    Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

  5. FY 1999 report on the results of the experimental verification on the establishment of a centralized load control system. Study of an advanced centralized load control system, etc.; 1999 nendo fuka shuchu seigyo system kakuritsu jissho shikehn kodo fuka shuchu seigyo system nado no kenkyu. Fuka shuchu seigyo system kakuritsu jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the FY 1999 results of the experimental verification on a centralized load control system for the residential electric power demand. The air conditioning control is effective for load leveling, and for it, it is important to infiltrate the consciousness of energy saving into people. Users are not very interested in the information on power rates, would rather tend to seek comfortableness, and are less conscious of energy saving on days of unusual summer heat. Further, the power control in peal time zone was made by indicating users the actual state of power use by a combination of the two-way communication and the automatic meter reading system. However, at present, it cannot be denied that the power rate is higher even in indirect load control equipment with necessary/minimum conditions than the existing power source. It is a must to reduce the cost. The liberalization of electric power is progressing fast, and incentives for DSM are decreasing, but each of advanced countries is getting sensitive to the obedience to COP3. In addition to DSM such as the rebate program and financing program by the existing surcharge system, they are making efforts for development/promotion of new energy by creating the green electric power market. The load control technology is expected which does not disturb comfortableness and amenity of users. (NEDO)

  6. Achievement report for fiscal 1981 on Sunshine Program-assisted project. Research and development of materials for coal liquefaction plant (Research on materials); 1981 nendo sekitan ekika plant zairyo no kenkyu kaihatsu (zairyo no kenkyu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Research and development is started of materials for constituting a liquefaction reactor which is the primary apparatus in the coal liquefaction process. Tested in the basic research on the designing of alloys for the reactor are Cr-Mo-V-Ti based alloys prepared by adding V, Ti, and B to Cr-Mo based alloys presently in use as materials for pressure vessels. They are melted and 50kg test ingots of steel are prepared, and an alloy with a constitution of Low Si-3%Cr-1%Mo-0.25%V-0.02%Ti-0.002%B is selected. In the designing of alloys to serve as stainless steel overlay welding materials and in the development of basic welding technologies, studies are conducted in search for materials that exhibit excellent durability under the conditions of liquefaction reaction and for technologies in this connection. These are accomplished using a test device installed this fiscal year, which is capable of reproducing high-temperature high-pressure hydrogen atmosphere. As the result, basic technologies are acquired, which will enable the achievement of the goal. In the study of on-site production technologies using medium-size ingots as the materials, an 85-ton medium size steel ingot of a new chemical constitution of Low Si-3Cr-1Mo-1/4V-Ti-B is melted, and a shell which is 400mm in thickness and 2m in internal diameter is forged, and the shell is subjected to a property and performance qualification test. (NEDO)

  7. Fiscal 1992 research report. Research trend survey of research and development of advanced materials for extreme environments (Carbon composite material); 1992 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu chosa hokokusho. Tansokei fukugo zairyo ni kakawaru kenkyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Trends of research on carbon based composite materials were surveyed through studying various reports and technical literature and evaluation of the project named above was conducted through holding interviews with researchers. In the survey of research trends for which technical literature perusal was the main tool, it was found that in most technical articles the important task was the enhancement of oxidation resistance, that SiC coating was in use for this purpose, that the technology would meet its limit at 1,600-1,700 degrees C, and that it would turn useless at temperatures beyond 1,800 degrees C. For the evaluation of the project, interviews were held with nine researchers not taking part in the project. The researchers favored the project as far as the popularity of the project and the main implementing body and system were concerned, but they negatively evaluated the project's goal of using such materials at 2,000 degrees C in the atmosphere. This research report comprises four chapters which cover (1) trends of research on C/C (carbon/carbon) composites, (2) a summarized research report on C/C composites, (3) survey of patents associated with C/C composites, and (4) opinions expressed toward the project and the results of evaluation conducted on the same. (NEDO)

  8. Fiscal 1993 achievement outline. Research and development of advanced materials for extreme environments (Advanced composite material); Chotaikankyosei senshin zairyo no kenkyu kaihatsu (senshin fukugo zairyo). 1993 nendo seika gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Efforts were made to develop technologies for C/C (carbon/carbon) composite materials and SiC fiber reinforced intermetallic compound composite materials. The efforts involved (1) creation of carbon based composite materials, (2) advanced composite materials, (3) fiber reinforced intermetallic compound composite materials, and (4) comprehensive research activities. In the research, coordination was established between the three technological fields, test standards common to the three were worked out, and relevant technologies were investigated. Studied for development under item (1) were coal pitch derived carbon fiber/carbon based matrix composite materials, PAN (polyacrylonitrile) based carbon fiber/carbon based matrix composite materials, and oxidation resistance enhancement technology. Studied for development under item (2) were oil pitch derived random structure carbon fiber, oil pitch derived onion structure carbon fiber, and oil pitch derived double structure carbon fiber/carbon based matrix composite materials. Studied for development under item (3) were SiC/SiMC (M=metal) silicon carbide based fibers and complexation of intermetallic compounds and the developed silicon carbide based fibers. (NEDO)

  9. Practical applications of superconducting technology; Chodendo gijutsu to sono oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, M.; Yamamoto, K.; Urata, M. [Toshiba Corp., Tokyo (Japan)

    1995-11-01

    Remarkable progress has been made in superconducting technology recently. This paper describes the details and technical features of every cooling type of practical superconducting magnet (SCM), including the SCM for magnetic resonance imaging (MRI), SCM for semiconductor pulling devices, high-field SCM, SCM for magnetically confined plasma devices, and SCM for particle detectors. Commercial production of pool-boil-cooled SCMs has been realized by reducing helium evaporation and decreasing the frequency of helium pouring. The development of forced-cooled SCMs has made it possible to build large SCMs. Moreover, the development of the 4 K-GM refrigerator has enabled liquid-helium-free SCMs to be introduced. Since this type of SCM can be operated merely by turning on a switch, SCMs are expected to come into more widespread use. 7 refs., 1 fig.

  10. Automobiles and safety; Jidosha gijutsu. Jidosha to anzen

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, K.; Goto, T.; Shimizu, T.; Yamanaka, A. [Toyota Motor Co. Ltd., Aichi (Japan)

    1998-08-01

    The number of road traffic victims in Japan has been above the level of 10,000 annually during 8 consecutive years, but in 1996 and 1997, it becomes below this level. The casualty of road traffic accidents is found to be occurred during driving and senior persons account for a large part among victims while 55.1% of the case took place at night. As for the countermeasures, it is possible to indicate the regulatory strengthening, advancement of accident investigation and analysis, provision of safety information to the user and research and development of advanced safety vehicle (ASV). Concerning preventive safety, studies on the human recognition, systems for assisting judgement and running and so on can be enumerated. The ASV is in the course of 2nd program that lasts until 2001 with 6 safety research subjects such as prevention, collision, automatic operation, containment of disaster from expanding and so forth. In terms of post-accident safety, remarkable research and development have been conducted on collision by means of dummy and human body, human resistance against injury, air bag for rider protection and child seat, and especially the form comparison of interior materials for head protection apparatus as well as study via simulation, together with commercialization of side bag for reducing head damages. As for car body materials, energy absorption by pillar type elements, use of aluminum materials, resistance comparison and design concept of structural separation and so on are being carried out. 69 refs., 1 fig.

  11. High-level water purifying technology. Kodo josui shori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsugura, H; Tsukiashi, K [Meidensha Corp., Tokyo (Japan)

    1993-07-01

    Research and development have been carried out on a high-level water purifying system using ozone and activated charcoals to supply drinking water free of carcinogenic matters and odors. This system comprises a system to utilize ozone by using silent discharge and oxygen enriching device, and a living organism/activated charcoal treatment system. The latter system utilizes living organisms deposited on activated charcoal surfaces to remove polluting substances including ammonia. The treatment experimenting equipment comprises an ozone generating system, an ozone treating column, an activated charcoal treating column, an ozone/activated charcoal control device, and a water amount and quality measuring system. An experiment was carried out using an experimental plant with a capacity of 20 m[sup 3]/day on water taken from the sedimentation process at an actual water purifying plant. As a result, trihalomethane formation potential was removed at about 40% in the ozone treatment, and at 70% in the whole treatment combining the ozone and living organism/activated charcoal treatments. For parameterization of palatability of water, a method is being studied that utilizes nuclear magnetic resonance to investigate degrees of water cluster. The method is regarded promising. 1 ref., 4 figs.

  12. Photon technology. Laser processing technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey has been conducted to develop laser processing technology utilizing the interaction between substance and photon. This is a part of the leading research on photon technology development. The photon technology development is aimed at novel technology development highly utilizing the quantum nature of photons. In the field of laser processing, high quality photons are used as tools, special functions of atoms and molecules will be discovered, and processing for functional fabrication (photon machining) will be established. A role of laser processing in industries has become significant, which is currently spreading not only into cutting and welding of materials and scalpels but also into such a special field as ultrafine processing of materials. The spreading is sometimes obstructed due to the difficulty of procurement of suitable machines and materials, and the increase of cost. The purpose of this study is to develop the optimal laser technology, to elucidate the interaction between substance and photon, and to develop the laser system and the transmission and regulation systems which realize the optimal conditions. 387 refs., 115 figs., 25 tabs.

  13. Microbial EOR technology; Biseibutsu EOR gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Taguchi, M.; Yonebayashi, E. [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan)

    1995-11-10

    This paper describes attempts of establishing an oil recovery technology utilizing microorganisms and of aiming at improving the practicability of that technology. Fiscal 1994 has investigated effects of inorganic salts existing in reservoir beds and NaCl concentrations on proliferation of microorganisms and production of metabolites. The investigation was intended to discuss applicability of microorganisms to environments that are brought closer to actual field conditions. Furthermore, a core sweeping test using sandstone was carried out on the fiscal 1992 separated bacteria, the 4118 bacteria, that has high surfactant production capability. In addition, a sand pack was used to perform a flooding experiment under conditions of 50{degree}C and 50 KSC to evaluate functionality of microorganisms when environments in the reservoir bed are simulated with respect to pressures and temperatures. An oil recovering experiment was carried out using a sandstone with a diameter of 1.5 inches, a length of 1.0 foot and permeability of 600 md, and using Bacillus subtilis 4118 bacteria which attained the lowest interfacial tension among the bacteria examined. A recovery rate of 4.4% Sor was derived in the experiment. A recovery rate of 29.0% Sor at maximum was obtained when Bacillus licheniformis 18-2-a bacteria was supplied into a sand pack filled with silica sand. 20 figs., 7 tabs.

  14. Photon technology. Laser process technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing laser process technology by interaction between substance and photon, the present state, system, R and D issues and proposal of such technology were summarized. Development of the photon technology aims at the modification of bonding conditions of substances by quantum energy of photon, and the new process technology for generating ultra- high temperature and pressure fields by concentrating photon on a minute region. Photon technology contributes to not only the conventional mechanical and thermal forming and removal machining but also function added machining (photon machining) in quantum level and new machining technology ranging from macro- to micro-machining, creating a new industrial field. This technology extends various fields from the basis of physics and chemistry to new bonding technology. Development of a compact high-quality high-power high-efficiency photon source, and advanced photon transmission technology are necessary. The basic explication of an unsolved physicochemical phenomenon related to photon and substance, and development of related application technologies are essential. 328 refs., 147 figs., 13 tabs.

  15. Technique of CWM distribution system; CWM ryutsu chukei system gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Konno, K [Center for Coal Utilization, Japan, Tokyo (Japan); Tanaka, M

    1996-09-01

    It may be intended that CWM is manufactured in areas near coal producing areas in overseas countries and imported as a product requiring lower handling cost than in bulk products. In order to achieve this idea, it is necessary to establish a distribution and relaying system for product transportation inside and outside the country, including relaying bases for receiving, loading and storing the product. This paper reports results of the demonstration tests performed since 1992 to 1996. In the tests, CWM made from Chinese coals was transported from Shijiu Port to the Hibiki relaying base in the city of Kita-Kyushu on 5000 DWT ocean vessels, unloaded, stored, and loaded again on 700 DWT domestic vessels for distribution to users. Since the inauguration of transportations, 40,000 tons of CWM were delivered yearly to the Okayama plant of Tayca Company, and about 20,000 tons to the Mizushima power plant of the Chubu Electric Power Company over a period from 1995 to 1996. During the period, a number of findings were acquired in different aspects, including quality control of incoming and outgoing CWM, stability in quantity and properties, loading and unloading works, and transportation. Although reduction in subsidence during transportation and storage was indicated desirable, the practical applicability was verified for the relaying system as a whole. 4 refs., 15 figs., 3 tabs.

  16. Technology for improving sludge concentration; Odei noshukusei kaizen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-10

    Sludge generating in a sewage treatment plant is disposed through the processes such as concentration, dehydration, and incineration in sludge disposal facilities. In recent years, there has been a trend that this sludge increases in volume as well as worsens in the concentration. A case is predictable where the sludge load to the dehydrating process is so large that the sludge can no longer be processed in sufficient quantity. In the meantime, if sludge is ozone-treated, viscous substance on the surface of sludge particles can be separated with a comparatively small amount of ozone, with sludge concentration enhanced. At Meidensha, an experimental plant was set up for the ozone treatment of sludge in a sludge intensive treatment plant of a metropolis, with a verification experiment carried out for a sludge concentration improving system by ozone. As a result of comparison of the treatment performance between an assessment system for performing ozone treatment and a reference system for not performing, the average value of the sludge concentration of a gravity concentration tank was 1.9% of the reference system against 1.7% of the assessment system in a continuous treatment experiment in the summer, while the solid collection ratio was 65.8% of the reference system against 95.5% of the assessment system, enabling a superior improving effect to be obtained. (NEDO)

  17. Winter concrete; Kanchu kunkurito. Gijutsu no genjo to shorai tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Kamata, Eiji [Hokkaido University, Hokkaido (Japan)

    1998-11-10

    Much energy is consumed in order to carry out the winter concrete, and it becomes not always the work in the work environment of the amenity. Therefore, it wants to avoid it, if such work is possible. The winter concrete is a basis in carrying out the construction in cold region in all year. Large role is very much fulfilled for efficient operation of the construction industry in which foot of maintain is wide, activation of the regional economy of snows cold region such as the constant employment of construction worker, improvement in the social environment. Therefore, the popularization of the winter concrete technology is indispensable in the chilly snowy area, and it becomes the importance that the efficiency improvement is attempted. (NEDO)

  18. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research results of hard photon technology have been summarized as a part of novel technology development highly utilizing the quantum nature of photon. Hard photon technology refers to photon beam technologies which use photon in the 0.1 to 200 nm wavelength region. Hard photon has not been used in industry due to the lack of suitable photon sources and optical devices. However, hard photon in this wavelength region is expected to bring about innovations in such areas as ultrafine processing and material synthesis due to its atom selective reaction, inner shell excitation reaction, and spatially high resolution. Then, technological themes and possibility have been surveyed. Although there are principle proposes and their verification of individual technologies for the technologies of hard photon generation, regulation and utilization, they are still far from the practical applications. For the photon source technology, the laser diode pumped driver laser technology, laser plasma photon source technology, synchrotron radiation photon source technology, and vacuum ultraviolet photon source technology are presented. For the optical device technology, the multi-layer film technology for beam mirrors and the non-spherical lens processing technology are introduced. Also are described the reduction lithography technology, hard photon excitation process, and methods of analysis and measurement. 430 refs., 165 figs., 23 tabs.

  19. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the application of photon to industrial technologies, in particular, a hard photon technology was surveyed which uses photon beams of 0.1-200nm in wavelength. Its features such as selective atom reaction, dense inner shell excitation and spacial high resolution by quantum energy are expected to provide innovative techniques for various field such as fine machining, material synthesis and advanced inspection technology. This wavelength region has been hardly utilized for industrial fields because of poor development of suitable photon sources and optical devices. The developmental meaning, usable time and issue of a hard photon reduction lithography were surveyed as lithography in ultra-fine region below 0.1{mu}m. On hard photon analysis/evaluation technology, the industrial use of analysis, measurement and evaluation technologies by micro-beam was viewed, and optimum photon sources and optical systems were surveyed. Prediction of surface and surface layer modification by inner shell excitation, the future trend of this process and development of a vacuum ultraviolet light source were also surveyed. 383 refs., 153 figs., 17 tabs.

  20. Paradigm for new scientific technology; Shinkagaku gijutsu paradigm

    Energy Technology Data Exchange (ETDEWEB)

    Shindo, Y [National Chemical Lab. for Industry, Tokyo (Japan)

    1995-01-05

    This paper reviews the current status from the standpoint of chemical engineers facing the coming of the 21st century, and surveys the paradigm for new scientific technologies. The criticism is mixed with unique opinions everywhere, such as `departure of students from scientific and engineering faculties is none other than the result of a market principle`, `national burden of trillions of yens should not be spent only under a justice of advancement of the science`, and `the global civilization itself has no other way but to change from the conventional expansive development type of the western country style to the internal development type of the oriental country style`. Values that define the paradigm for new scientific technologies may include such keywords as saturation in technology, baseless expansion of research projects, criticism on science, market principle, and centering human being. It should be looked at seriously that profit from research and development should exceed the cast invested therein in the future, and scientific technologies that serve truly the society should be aimed at. These efforts will result in one of the large pillars that support the future in which creation of new functions is aimed at as a result of structuring the new systems. Trying to overcome the environmental problems is one of them.

  1. Laser innovated manufacturing technology; Laser ga seisan gijutsu wo kakushinshita

    Energy Technology Data Exchange (ETDEWEB)

    Maruyama, I. [Honda Motor Co. Ltd., Tokyo (Japan)

    1996-11-01

    This paper looks back the history of applications of laser processing in the automobile industry, and introduces contents of some particularly unique applications from among them. The CO2 laser and YAG laser that are used mainly have increased their outputs with the times, and 50-kW CO2 laser and 4-kW YAG laser have now become available commercially. The laser processing has become used widely for cutting purpose in Japan, which is in contrast with their high application to welding in Europe and America. Cutting thick plates has been developed recently, which is applicable to plates as thick as about 25 mm. A flexible system in which YAG laser is combined with an optical fiber/articulated robot is operating for three-dimensional shape processing. Automobile makers are adopting laser processing for welding in place of the electron beam welding that has been used conventionally. The process is used also for a number of other applications including surface reformation, such as surface quenching for cylinder liner, and valve seat padding. 8 refs., 8 figs.

  2. Evaluation technology of clothing comfortableness; Ifuku tekigosei hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Niwaya, H.

    1999-10-26

    Modern apparel industries are required to supply many kinds of products corresponding to various needs of consumers. Among consumers' needs, comfortableness to wear such as size-fitness is primarily important. To facilitate apparel industries, it is expected to develop a new technology of pattern designing of comfortable garment and measuring garment pressure distribution. Our research is aimed at developing technology that uses computer simulation to predict and evaluate wear comfort, including size suitability, without the need to actually sew up a garment. First, we developed a basic system to predict wearing silhouette, garment pressure, and ease looseness of the garment. Using this system, we carried on the following study. The 3-dimensional distributions of the garment pressure and ease looseness were reversely mapped on the paper pattern in order to indicate the preferable modification. The system was extended for several poses, e.g. twist, bend. From various parameters, we examined the factors of garment pressure and ease looseness. In addition, we selected the parameters for the size-fit indicators and investigated size-fit evaluation indicators. (author)

  3. FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

  4. Investigational research on highly functional carbon and related materials (HF-CRMs); Tansokei kokino zairyo no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper arranged a fiscal 1997 guiding study of highly functional carbon and related materials (HF-CRMs). In the material invention field, described were the composition by interatomic control technology and the characteristics of pure carbon nanotubes, carbynes, graphite, fullerene polymer, porous carbon, etc. Heteroelement substituted materials were also described. The paper also reported the application of HF-CRMs to the electric/chemical field, and arranged the basement technology and applicability of diamond in particular. The subjects are enhancement of composition technology and reduction of the price of processing technology. Especially, the control of impurities and defects is a must for the electric use. The application of HF-CRMs to the mechanical field was reported. Superlubricant, wear resistant and high temperature corrosion resistant materials were taken up, and were surveyed in terms of their use mostly to refuse incineration power generation boilers, and thermal power generation use turbines. In the development of mechanical materials, technologies were surveyed especially for large area/complex shape film formation to form films for various parts, functionally gradient film formation for relaxation of thermal stress and residual stress in the film, and high speed film formation for quantity production. 363 refs., 88 figs., 10 tabs.

  5. Chalcogenide glasses as optical and ion-conducting materials. Kogaku oyobi ion dendo zairyo toshite no chalcogenide glass

    Energy Technology Data Exchange (ETDEWEB)

    Toge, N.; Minami, T. (Univ. of Osaka Prefecture, Osaka (Japan))

    1991-12-01

    Nonoxide glasses whose main constituent are chalcogen elements like S, Se, or Te etc. show a lot of various properties, for instance, high infrared transmittancy and semi-conductivity which are already well known. Additionally, the optical properties change a lot along with the phase transition's happening between crystal and noncrystal under comparative low temperature. Further, it is also observed that the glasses containing proper cation appear high ion-conductivity. This paper supplies a brief reviews of chalcogenide glasses used as materials for infrared fiber, phase transition optical memory and superionic conductor, wherein the former two have already on the stage of utilization, particularly the realization of a rewritable optical memory is possible by using chalcogenide glasses film, and ion-conductor is in the phase to have shown the possibility of high conductivity while the development thereof is being expected. 22 refs., 8 figs.

  6. Use technologies of organic materials under various environmental conditions; Kankyo joken no tayosei to yuki zairyo??????250KKGKA4

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, s. [Ajinomoto Co. Inc., Tokyo (Japan)

    1996-06-05

    This paper describes use technologies of organic materials for selecting them under various environmental conditions. FRP is superior in mechanical strength and chemical resistance, and suitable as anticorrosion structural materials. Its chemical resistance is dependent on matrix resins. Simple polyolefine system resin is superior in chemical resistance and cost, however, because of its poor mechanical strength, it is mainly used for small parts. The composite structure is used for middle tanks or piping materials where the inside surface contacting solution is lined with chemical resistant resins such as PP and PVC, while the outside surface is reinforced with FRP. Various lining materials and lining methods are used. The following materials are used for lining: liquid resin type one such as tar epoxy resin, melting powder type one such as PE, PP and fluororesin, laminated glass fiber type one using cold setting polyester and thermosetting phenol resin, compound type one of scale-like glass flake and resin, and rubber or plastic sheet material. It is important to select optimum material for lining. 1 fig., 2 tabs.

  7. Development of materials of `bekko work` using horn; Gyukaku riyo ni yoru bekko daitai zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Mori, S.; Nagata, S. [Technology Center of Nagasaki, Nagasaki (Japan); Sakoguchi, A. [Kumamoto Institute of Technology, Kumamoto (Japan)

    1996-11-10

    The technical art `Bekko` is one of the traditional technologies in Japan, and the materials of `Bekko` are shells of hawksbills. However, the industry of `Bekko Work` has been facing a crisis recently, because the import of turtleshell is restricted. We have therefore tried to develop new materials as substitutes for the turtleshell by utilization of horn. The noteworthy aspects in this study are as follows: (a) It has been clearly established that the horn could be reformed with amber color similar to that of turtleshell by chemical treatment using hydrogen peroxide (H2O2). (b) It is also of interest that we produced new materials like `Bekko` by mixing horn powder and turtleshell powder at the appropriate ratio and molding them in the temperature range of 110-120{degree}C. 1 ref., 6 figs., 3 tabs.

  8. Study on the creation of biopolymer materials under micro-gravity; Bisho juryokuka deno seitai kobunshi zairyo no sosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In order to create new functional organic thin film materials, basic data were examined under micro-gravity. Polymerization of pyrrole was affected by micro-gravity after a few minutes from the beginning of reaction. Although relatively uniform particles were obtained, the particle size was finely dependent on conditions. Electrolytic polymerization of conductive organic thin films was yet unstable in reproducibility. On orientation control and thin film formation of protein under gravity-free environment, electrodeposited films were obtained using bacteriorhodopsin film suspension by applying voltage of 6.4V for 9s after 1s from falling. The reproducibility of the number and area of molecular layers was poor. On the study on the formation process of organic thin films, creation of homogeneous films is probably possible by filtration from suspension under reduced pressure under micro-gravity for a short time. Trial linear polymer tied in a row was obtained by capillary injection of dense polymer solution. The viscous fingering phenomenon of viscoelastic bodies under micro-gravity was compared with that on the ground. 11 refs., 36 figs., 1 tab.

  9. Present status and future of various rubber materials. ; Asphalt. Kakushu gomu zairyo no genjo to kongo. ; Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Wakisaka, S. (Toa Doro Kogyo Co. Ltd., Tokyo (Japan))

    1991-12-15

    Asphalt is obtained at a rate of about 25 Kg per 1 Kl of oil and is produced at about 5 million tons per annum in Japan, 80 % of which is now used for the pavement of road. The purpose of this study is to examine the possibilities of developing new applications of asphalt to the anti-vibration, vibration-control and anti-noise materials, though its uses have already been diversified in fields other than for road paving, due to excellent performance regardless of cheap cost. In the paper, firstly, under a title of what is asphalt, the history, the composition and internal structure of asphalt were considered. Secondly, the dynamic characteristics of asphalt were considered. And lastly, under a title of the application of asphalt, examples of the application of asphalt to anti-noise materials were examined in the field of architecture, automobile and civil engineering respectively. Especially, in the field of civil engineering, improvements of flexibility and vibration-control by using the cement asphalt mortar (CAM) in the anti-vibration A-type slab track for railway, and also anti-noise and anti-vibration technologies applied to the road pavement body by using the ferrite asphalt were reviewed. 11 refs., 10 figs., 8 tabs.

  10. Mechanical properties of weft knitted fabric reinforced composites. Iamimono kyoka fukugo zairyo no rikigakuteki tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Wu, W.; Inoda, M.; Kotaki, M.; Goto, A.; Fujita, A.; Hamada, H.; Maekawa, Z. (Kyoto Institute of Technology, Kyoto (Japan). Faculty of Textile Science)

    1993-09-15

    Mechanical properties and failure behavior of weft knitted fabric reinforced composites were studied. Aramid fiber was used as reinforcement (knitting fiber), and epoxy resin as matrix. Different tensions were applied to the weft knitted fabric in a course or wale direction to prepare 5 kinds of fiber reinforced composites with different densities of the knitted fabric, and tensile test pieces were thus provided by cutting each composite in a course or wale direction. As a result, the weft knitted fabric reinforced composite offered a dynamical anisotropy, and the tensile strength of the test pieces was higher in wale direction than course one. Fracture in a course direction occurred at the section with extreme low fiber content, while fracture in a wale direction occurred at a loop interlocking region due to stress concentration. The tensile strength was constant or increased in a course or wale direction by stretching the knitted fabric before molding, respectively. 21 refs., 15 figs., 2 tabs.

  11. Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

  12. Development of advanced corrosion resistant materials for molten coal ash; Yoyu sekitanbai ni taisuru kotaishokusei zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For development of materials for heat exchangers under severe corrosion environment due to ultra-high temperature coal combustion gas, basic data were surveyed. On the study in fiscal 1996, the corrosion resistance of one kind of commercially available material and 2 kinds of created materials was studied by coal slag coating test. The commercially available material was subjected to high- temperature corrosion tests of 1500 and 1550degC for a long time. The result showed that SiC is most excellent in the above temperature range. On new materials, 7 kinds of Cr2O3 system ceramics such as Cr2O3-Al2O3 system and Cr2O3- MgO system were selected considering high-temperature corrosion resistance, and the optimum composition and fabrication process of the new materials were studied. High- temperature corrosion tests, and measurement of thermal conductivity and thermal expansion were carried out for every specimen. The result suggested that some materials of Cr2O3- Al2O3 system are promising. 23 refs., 76 figs., 23 tabs.

  13. Development of bushing material with higher corrosion and wear resistance; Taishoku taimamosei dogokin bush zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kira, T; Yokota, H; Kamiya, S [Taiho Kogyo Co. Ltd., Osaka (Japan)

    1997-10-01

    Recent diesel engines require a higher performance and a longer life. Due to higher cylinder pressure, the operating load and temperature of piston pin bushings become higher. Therefore, higher load capacity, higher wear resistance and higher corrosion resistance are required for piston pin bushings. For this reason, we have studied the effect of components added to copper alloy upon the corrosion resistance and the effect of hard particles dispersed in copper matrix upon the wear resistance and the influence of hard particles on the machinablity of materials. Based on the experimental results, we have developed a new bushing material improving wear and corrosion resistance. 17 figs., 3 tabs.

  14. Development of high-performance sintered friction material for synchronizer ring; Koseino shoketsu synchronizer ring masatsu zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyajima, K; Fuwa, Y; Okajima, H; Yoshikawa, K [Toyota Motor Corp., Aichi (Japan); Nakamura, M [Japan Powder Metallurgy Co. Ltd., Tokyo (Japan)

    1997-10-01

    Increasing vehicle speed and power, high-performance synchronizer ring of manual transmission is required. We develop double layer sintered synchronizer ring for high performance and cost reduction. The main structure is consisted of ferrous sinter for high strength. In this paper, friction materials of sintered synchronizer ring are studied. We can get the good friction and anti-wear property by means of hard particles (FeTi, ZrO2), solid lubricant (Graphite) and suitable porosity in brass sinter matrix. And we also achieve high joining strength between double layers adding Cu-P material. 6 refs., 13 figs., 2 tabs.

  15. Survey on peripheral techniques of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru shuhen gijutsu no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-09-01

    Described herein are results of survey on brown coal liquefaction techniques and peripheral techniques, centered by COSTEAM process under development in USA, solubilization by alcohol and liquefaction and cracking with the aid of tetrahydroquinoline as the hydrogen donor under development in Japan, and low-temperature carbonization and new promising techniques. The COSTEAM process shows higher reaction rates, conversions and oil yields for brown coal liquefaction than the one using hydrogen gas. Some of the problems involved in this process high viscosity and oxygenated compound content of the product oil. The product oil is acceptable as fuel for power generating plants and can be produced at a moderate cost, but may be unsuitable as vehicle fuel. Coal liquefaction and solubilization processes are mainly represented by those which use hydrogen. The hydrogen cost, which is high, determines the product price. The processes which use alcohol or tetrahydroquinoline are still in the experimental stage. (NEDO)

  16. Fiscal 1997 report on the results of the international standardization R and D. Robot control system; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Robot seigyo system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    R and D of the robot control system was conducted in the following items: 1) integrated open control system, 2) remote control robot manipulation language, 3) human factor robot use built-in LAN system, 4) built-in actuator driver. In 1), there were some problems to be pointed out around the system, but the effectiveness was confirmed as system architecture of each verification item. In 2), development/design were made of RCML(R-Cube Manipulation Language) as a remote robot manipulation language, telecommunication protocol, and the experimental system, and the international standardization was targeted. In 3), the R and D was conducted of the realtime telecommunication protocol which clears the standards for the distributed control required for construction of human factor robot and the advanced realtime micro-controller, ULSI, which is the one that the protocol was made IC. In 4), an intelligent connector for built-in actuator was developed which enables saving of wiring in robot system and plug-in connection. 13 refs., 186 figs., 53 tabs.

  17. Light beam control by refractive index change in a modified purple membrane; Hen`i shimaku no kussetsuritsu henka wo riyoshita hikari bimu seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Takei, H.; Shimizu, N. [Hitachi Ltd., Tokyo (Japan)

    1996-04-01

    A purple membrane extracted from bacterial halobacterium salinarium is a membrane prepared by two-dimensionally crystallizing bacteriorhodopsin (bR) which is a photo-sensitive protein. When retinal chromophore in the bR absorbs photons, isomerization occurs, so that light cycle of bR comprising a light intermediate of different absorption spectrum occurs. Since this purple membrane has a high stability and a high repetition durability, a study of the application of the same to a rewritable holographic recording medium has been made in recent years. This paper describes an example in which the refractive index variation of a purple membrane the optical characteristics of which varies due to variation is applied to light beam control. The paper introduces a Fabry-Perot resonator as an optical element capable of carrying out light control by utilizing refractive index variation. The paper further describes the possibility of materialization of an optical logic comprising a combination of light-irradiation refractive index variation and a Fabry-Perot resonator and having nonlinear input/output characteristics such as the bistablity owing to the feedback effect in the resonator. 7 refs., 3 figs.

  18. FY1995 distributed control of man-machine cooperative multi agent systems; 1995 nendo ningen kyochogata multi agent kikai system no jiritsu seigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the near future, distributed autonomous systems will be practical in many situations, e.g., interactive production systems, hazardous environments, nursing homes, and individual houses. The agents which consist of the distributed system must not give damages to human being and should be working economically. In this project man-machine cooperative multi agent systems are studied in many kind of respects, and basic design technology, basic control technique are developed by establishing fundamental theories and by constructing experimental systems. In this project theoretical and experimental studies are conducted in the following sub-projects: (1) Distributed cooperative control in multi agent type actuation systems (2) Control of non-holonomic systems (3) Man-machine Cooperative systems (4) Robot systems learning human skills (5) Robust force control of constrained systems In each sub-project cooperative nature between machine agent systems and human being, interference between artificial multi agents and environment and new function emergence in coordination of the multi agents and the environment, robust force control against for the environments, control methods for non-holonomic systems, robot systems which can mimic and learn human skills were studied. In each sub-project, some problems were hi-lighted and solutions for the problems have been given based on construction of experimental systems. (NEDO)

  19. Starting and stopping control on power conditioner in photovoltaic power system; Taiyoko hatsuden system ni okeru power conditioner no kido teishi seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Hirose, M.; Ishihara, Y.; Todaka, T.; Harada, K. [Doshisha University, Kyoto (Japan); Oshiro, H.; Nakamura, H. [Japan Quality Assurance Organization, Tokyo (Japan)

    1997-11-25

    Studies are made about the control of the power conditioner over the maximum power point tracking (MPPT) function in a photovoltaic power generation system. The analysis is conducted by means of computer simulation into the effect of a start/stop function added to the control of MPPT and the effect on the generation of power of the setting of parameters in the start/stop function. The reduction in output power due to difference between the actual operation point and the optimum operation point is evaluated by use of a load matching correction factor. In this simulation, it is assumed that the solar cell array consists of 13 rows in 5 parallel columns, is capable of a normal output of 3.149kW, has a panel tilted at 30 degrees, and faces due south. The power conditioner is assumed to be a system rated at 3kVA, equipped with system interconnection and back flow features. As a result, it is learned that the stop voltage should be set at 180V or lower and the steady voltage near 185.5V for a good result and that there is not much need after all for the start/stop technique. 2 refs., 8 figs., 2 tabs.

  20. On-line temperature control of fluidized bed incinerator using fuzzy algorithm; Fuzzu seigyo donyu ni yoru ryudosogata shokyakuro unten no jidoka

    Energy Technology Data Exchange (ETDEWEB)

    Okayasu, S.; Kuratani, T.; Imai, H. [Ajinomoto Co. Inc., Tokyo (Japan)

    1995-03-15

    Automatic control of incinerators for their stable operation has been desired for the preservation of the environment in the factory. An on-line fuzzy control system has been successfully introduced for temperature control of the fluidized bed of incinerator for industrial wastes. In this case, manual control can be applied to the plant instead of a PID control system, because of the complexity of the waste materials and the large delay in detection of the temperature change in the fluidized bed sand. On the basis of analyzing the dynamic performance of the process and the know-how of skilled operators, membership functions and fuzzy control rules are selected, then determined carefully for the system. Introduction of the system resulted in almost the same performance as manual control. Subsequently the operators are freed from manual operation in the control room for an hour. 6 refs., 5 figs., 4 tabs.

  1. Application of photo-excitation reaction on titanium oxide thin film for control of wettability; Sanka chitann hakumakujo no hikari reiki hanno no nuresei seigyo eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Nakajima, A.; Hashimoto, K. [The Univ. of Tokyo, Tokyo (Japan); Takada, Y. [Kyushu Univ., Fukuoka (Japan)

    2000-03-31

    It is clarified that the photo-excitation hydrophilic reaction increasing wettability remarkably is induced by changing surface structure of titanium oxide radiated light. There are already many examples being in practical use of coating products applied hydrophilic reaction of titanium oxide surface such as drip-proof side millers for automobiles, self-cleaning building materials, and the like. When surface of titanium oxide having high activities for oxidisation and decomposition is coated organic materials and radiated light, wettability of surface changes as organic materials are decomposed. If it is possible to change wettability shaping pattern drastically by radiating light, the possibility of application for printing materials will be developed. After increasing contact angle by coating water and oil repellent on the titanium oxide thin film, images can be shaped by radiating light into pattern for changing surface of titanium oxide to be ultra hydrophilicity as decomposition of repellent. At that time, contact angle is 150 degree in water, 80 degree in oil, for not radiated aria, and is 0 degree in water and oil for radiated aria. Application for control technology of wettability keeps possibility of broader development to itself, not staying ability of self-cleaning and drip-proof. (NEDO)

  2. Control of population of excited nitrogen molecules by mixing hydrogen in low pressure discharge; Chisso jun`antei reiki bunshi mitsudo no quenching ni yoru seigyo no kento

    Energy Technology Data Exchange (ETDEWEB)

    Uematsu, K.; Yumoto, M.; Sakai, T. [Musashi Institute of Technology, Tokyo (Japan)

    1998-06-01

    The authors have studied on surface treatment of PTFE by a low pressure discharge. It is deduced that excited nitrogen molecules contribute to introduce polar components on the surface. To confirm the speculation, we tried to change population of metastable nitrogen N2 (A{sup 3}{Sigma}u{sup +}) by quenching precursor N2 (B{sup 3}{pi}g), with hydrogen molecule. The decrease of relaxation time which indicates a change of excited molecule and measured by emission spectroscopy using a time after glow method was obtained. As a result, the relaxation times of N2 (B{sup 3}{pi}g) and N2 (A{sup 3}{Sigma}u{sup +}) decreased to 55% and 20% respectively, when mixing ratio of hydrogen was 3%. It was also deduced that hydrogen atom may take a part in a quenching process of N2 (A{sup 3}{Sigma}u{sup +}). 14 refs., 11 figs., 1 tab.

  3. Study on heavy duty truck stability control by braking force control; Seidoryoku seigyo ni yoru truck no sharyo kyodo anteika ni taisuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, K; Shinjo, H; Harada, M; Ohata, K; Sakata, K [Mitsubishi Motors Corp., Tokyo (Japan)

    1997-10-01

    Now a days we are discussing about the vehicle stability control system which freely controls the braking force of each wheel to apply the yaw t and decelerate the vehicle. The system drastically improve the vehicle cornering performance and stabilize the vehicle behavior in its critical area. This paper discusses a point to notice in case of applying this technique for heavy duty trucks, and describes the possibility of the stabilization for vehicle cornering behavior about heavy duty truck. 3 refs., 10 figs., 2 tabs.

  4. Development of combustion management concept for natural-aspirated small diesel engine; Shizen kyuki kogata diesel engine no nensho seigyo concept no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Wada, T; Kawano, T; Shoji, M; Kuniyosh, M; Yamashita, O; Nagao, A [Mazda Motor Corp., Tokyo (Japan); Yoshikawa, S [Zexel Corp., Tokyo (Japan)

    1997-10-01

    We have developed a combustion management concept for natural-aspirated small IDI diesel engines and achieved higher power, lower exhaust emissions and more comfort. The concept is related to improvements of intake volumetric efficiency, EGR effect, mixture formation caused by combustion chamber and spray characteristics, engine management system and after treatment device. This paper describes the concept and experimental results. 3 refs., 14 figs., 1 tab.

  5. Optical axis control system as unification of reflex and pursuit eye movements; Zentei dogan hansha, shikisei hansha, katsudosei undo wo togoshita gankyu undo seigyo model

    Energy Technology Data Exchange (ETDEWEB)

    Wakamatsu, H.; Zhang, X. [Tokyo Medical and Dental College, Tokyo (Japan)

    1997-10-20

    In order to realize basic optic axis movements, by which a moving target can be caught in a central pit of retina, an oculomotor mathematical model is developed for horizontal movements of a head and an eyeball. An image signal from retina and an acceleration signal from semicircular ducts are used as control inputs to muscles of eyeball to realize appropriate eye movements taking into account the displacement of a head rotation. Reflex eye movements and smooth pursuit as autokinesis are discussed with consideration of their control performances which lead to automatic cooperation of an appropriate control system according to the movement types of an target. The optic axis is controlled by a unified eye movement system which is synthesized on the basis of various biological facts. It has a flexible dynamics characterized by variable parameters which imply anatomical structure and physiological mechanism given by the change of synaptic conductivities in flocculus. The basic physiological facts are presented under the corresponding anatomical and physiological conditions given by appropriate changes of mathematical description of the proposed model. 14 refs., 16 figs.

  6. Report on achievements in fiscal 1999. Research and development of nanometer controlled optical disk system; 1999 nendo nanometer seigyo hikari disk system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Organizational strengthening is urged in industrial technological power in information recording area which is comparable with information communications being the main pillar of the innovation in the information technology in Japan. Extremely large expectations and heavy responsibilities are placed on the next generation optical memory technology, which is one of the strong points of Japan who plays a part in the above information recording area. The present project has been performing organizational research and development to achieve creation of new industries, with the following research themes as the main subjects: (1) nanometer controlled optical memory technology, (2) magnetic section responsive and three-dimensional optical memory, (3) ultra precision pit depicting technology, and (4) ultra precision pit measuring technology. The project is two years old this year, in which it was aimed to 'develop an optical memory technology with recording density of 100 Gb/in{sup 2} or more, transfer velocity of 100 Mbps or higher, and access time of 10 ms or less'. In order to achieve and establish the interim target set for fiscal 2000 among the above aims, intending 'trial fabrication of a disk having recording density of 40 to 50 Gb/in{sup 2}, the technical problem extraction and the specifications to realize a 100 Gb/in{sup 2} system', fiscal 1999 has performed researches on 'density and accuracy improvement on the prototype disk by improving the existing devices and introducing new devices'. This paper reports the developmental research theme No. 1. (NEDO)

  7. Optimal control of aerobic bacteria fermentaion by dynamic programming method. Doteki keikakuho ni yoru kokisei saikin hakko process no saiteki seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Kidoushi, H; Murayama, S; Shiomi, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Haneda, K; Yamada, Y [Asahi Chemical Industry Co. Ltd., Tokyo (Japan)

    1991-05-10

    A dynamic programing method was applied for maximizing a production yield in controlling the process of aerobic bacteria fermentation. An optimal control was carried out by air flow rate under a sufficient sugar supply condition, using the bacteria amount as a state variable and the air flow rate as an operation variable, under conditions where the sugar consuming rate is not a limiting factor. The growth and production were modelled, and the relationship of both the specific growth rate and the specific production rate to the specific respiration rate was was expressed as functional tables. A simulation was carried out, which provided an optimum air flow pattern. This relationship between the bacteria amount and the optimum air flow rate was mapped to perform a map control. Conditions other than the air flow pattern were made to agree with the previous empirical cultivation method, and experiments were conducted using a cultivation tank of 0.03 m {sup 3}. A yield increase of 13.6% over the conventional method was attained, thus the reasonability of the modelling was verified. It was found that there are portions where the width of the optimum air flow control is wide and narrow, and it is possible to reduce the number of maps if this this is taken into account. 4 refs., 8 figs., 2 tabs.

  8. Study on the detonation properties of explosives in bore hole and precise controlled blasting; Happa konai no bakuyaku no bakugosei to seimitsu seigyo happa ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-08

    In order to perform efficient and safe controlled blasting, attaining sufficient detonation from explosive is important. Therefore, a mechanism of detonation in a bore hole was studied. Two detonation phenomenon measuring methods were established: one is a continuous detonation speed measuring method by using a resistance wire probe, and another is a detonation mark observing and evaluating method using aluminum and metallic lead plates. Assuming delay blastings in multiple bore holes used practically, discussions were given on detonation phenomena of explosives under pressurized condition. Under dynamic pressure condition, size of the pressurization and delay time of the detonations affected largely the detonation. Discussions were given on blasting effect and safety according to difference in forward initiation and reverse initiation. The reverse initiation method was verified to have excellent blasting effect, maintain good face conditions, and assure safety against inflammable gases. A precision initiation method was developed, which can control the initiation time of a detonator more precisely. The initiation accuracy is more than 1000 times greater than the ordinary instantaneously detonating electric detonator. The precision control of the initiation time proved to develop greater crack propagation. Vibration and stone scattering were also controlled. This paper also describes application of the method to a rock elastic wave exploration technique. 136 refs., 99 figs., 13 tabs.

  9. Method of estimating time management of safety control of combustion. Nensho anzen seigyo no tame no jikan kanri No hyoka hoho

    Energy Technology Data Exchange (ETDEWEB)

    Moroboshi, M. (Yamatake-Honeywell Co. Ltd., Tokyo (Japan))

    1993-12-01

    The results of investigating time management (permissible value of ignition time and prepurge time) for safety control of combustion relating to a combustor is reported. It is shown that the heating value of hydrocarbon-based fuel is determined by molecular weight irrespective of molecular structure and constant (11200kcal/kg) per unit weight; the heating value of mixture gas of theoretical mixture ratio is constant (1000kcal/m[sup 3]) indifferently of the kind of fuel; and that the product of the heating value of a fuel and the lower limit of its explosion limit is approximately constant (400-600kcal/m[sup 3]). Succeedingly it is shown based on these values that allowable ignition time is determined by the combustion chamber load (ratio of the maximum amount, 10[sup 4]kcal/h, of combustion to the volume of combustion chamber); the effect of dilution by exhaust lengthens it by only about 50%; and that the conventional criterion that the frequency of ventilation of prepurge should be 4-5 or that the minimum time of prepurge should be 30 seconds is appropriate. 6 refs., 4 figs., 1 tab.

  10. Achievement report on research and development of optics-aided measurement/control system; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    The project aims to establish technologies for putting the above-named system to practical use. Such a system will measure, transmit, and control, with safety and stability by use of optical technologies, industrial process related information to be generated in certain areas such as industrial complexes and very large plants, the information including images, temperatures, flow rates, constituents, etc. Total system evaluation was performed in demonstration tests for appropriateness conducted for 32 systems in fiscal 1980 and 10 systems in fiscal 1981. Studied in the development of element technologies are opto-electronic integrated circuits (OEIC), semiconductor laser devices, light-intercepting devices, optical transmission paths, dielectric light switches, and optical sensors. For OEIC, in particular, since it is believed to be the nucleus of an optical application system, an optical technology joint research office is established, where efforts center on the substrate crystal growth technology, process technology, and crystal/process evaluation technology. (NEDO)

  11. Fiscal 2000 achievement report on the research and development of nanometer controlled optical disk system; 2000 nendo nanometer seigyo hikari disk system no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Development proceeded of nanometer controlled optical memory technologies as part of systematic research and development aiming at the reinforcement of industrial technology power in the field of data recording. Activities were conducted in the four fields of (1) high density signal processing technology, (2) high performance disk materials technology, (3) disk substrate fabrication technology, and (4) signal detection technology. Discussed in field (1) were multivalue ROM (read only memory) disk signal regeneration, SIL-LBR (solid immersion lens-laser beam recorder), dry etching process using RIE (reactive ion etching), SHG (second harmonic generation) blue laser, and a multivalue ROM disk evaluation system. Studied in field (2) were the evaluation of ROM disk performance dependent on recording materials, development of high density recording materials, and the evaluation of crystallization induction time using a static tester. Studied in the development of high density recording materials was the formation of microscopic recording marks in a phase shift/surface recording type disk comprising a 4-element (Ag-In-Sb-Te) recording layer and an Ag reflection layer. In fiscal 2000, an attempt was made at the 0.07 {mu}m level. (NEDO)

  12. ISC feedforward control of gasoline engine. Adaptive system using neural network; Jidoshayo gasoline engine no ISC feedforward seigyo. Neural network wo mochiita tekioka

    Energy Technology Data Exchange (ETDEWEB)

    Kinugawa, N; Morita, S; Takiyama, T [Osaka City University, Osaka (Japan)

    1997-10-01

    For fuel economy and a good driver`s feeling, it is necessary for idle-speed to keep at a constant low speed. But keeping low speed has danger of engine stall when the engine torque is disturbed by the alternator, and so on. In this paper, adaptive feedforward idle-speed control system against electrical loads was investigated. This system was based on the reversed tansfer functions of the object system, and a neural network was used to adapt this system for aging. Then, this neural network was also used for creating feedforward table map. Good experimental results were obtained. 2 refs., 11 figs.

  13. Crystal from and aggregate controls of hydroxyapatites and related phosphates; Suisan apataito oyobi kanren rinsan enrui no kessho oyobi kessho shugotai no keitai seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, N.; Wakana, Y.; Kaji, H. [Taihei Chemical Industrial Co. Ltd., Osaka (Japan)

    1995-09-01

    Potassium phosphates are compounds with the composition of Ca/P=0.5-2.0, and regarding potassium phosphates of apatitic structure, research has been made in the fields of biomaterial, base material for tooth paste, base material for cosmetics, etc. since 1980`s. In particular, hydroxyapatites (HAP) and tricalcium phosphates (TCP) are now sold as artificial bones, artificial tooth roots, etc.. In this article, the synthetic methods and morphological controls of HAP, TCP, tetracalcium phosphates (TTCP) and fluorine apatites (FAP), and the properties of products of 4 kinds of hydroxyapatites (HAP-100, HAP-200, HAP-300, and spherical HAP), 2 kinds of tricalcium phosphates ({beta}-TCP-100 and {alpha}-TCP), TTCP and FAP are introduced. The particle morphology of the above chemical compounds depend on the respective synthetic methods and stable production of calcium phosphates require technology as well as facilities of high degree. 26 refs., 17 figs., 2 tabs.

  14. Resistance test of high-speed ship by means of attitude control method. Part 2; Shisei seigyo hoshiki ni yoru kosokutei no teiko shiken. 2

    Energy Technology Data Exchange (ETDEWEB)

    Hayashida, S [Nagasaki Institute of Applied Science, Nagasaki (Japan)

    1996-04-10

    The previous paper has proposed a resistance test method by controlling the attitude of a high-speed model ship using a personal computer without making a data base. For this method, the fluid force acting on the hull of model ship is measured, to change its attitude based on the measurement, and then, the fluid force is measured again, to change the attitude again. The traveling attitude is created by repeating this, to measure the force acting on the hull. Since the attitude is changed by calculating using the fluid force measured, various factors can be considered in the calculation process. For example, a test with an arbitrary displacement in an arbitrary position of center of gravity can be conducted in spite of actual displacement and position of center of gravity of the model ship. A test for a high-speed ship was conducted through this method, to obtain nearly satisfactory results compared with a usual resistance test. Occasionally, a lot of repetitions were required to satisfy the balancing condition of the force. In this study, the improvement of testing efficiency has been planned by modifying the analyzing program. 5 refs., 7 figs., 1 tab.

  15. Fixed position holding control for self-propulsion barges under disturbance condition; Gairanka ni okeru jiko baji no teiten hoji seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kijima, K; Murata, W; Furukawa, Y [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1996-04-10

    In direct hoisting work in suspension bridge construction, since a cable crane directly hoists a bridge beam block put on a barge on the sea, precise fixed position holding function is required for a barge. The control system was then designed on the basis of an ILQ control theory, and the effect of change in time constant as design parameter on fixed position holding performance was studied. In addition, the critical disturbance for fixed position holding control was studied through numerical simulation under various disturbance conditions using the above designed control system. As a result, in the design of control systems on the basis of an ILQ control theory, the precise control system could be designed by diminishing, in particular, the time constant for state variable around a z axis among time constants according to the extent of disturbance. The control performance was largely affected by response delay period from sensing of disturbance to beginning of control. 3 refs., 7 figs., 2 tabs.

  16. Control of pouring molten charge out of a levitation type cold crucible; Fuyogata cold crucible kara no hiyukaibutsu no chuto seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Ando, K.; Iwai, K.; Asai, S. [Nagoya University, Nagoya (Japan). Faculty of Engineering

    1994-10-25

    The cold crucible is a high-frequency induced heating melting process consisting of the cold copper crucible, coil, and charge. The levitation type crucible is of the cup type device, with the magnetic field concentrated to the vicinity of the hole in its bottom, so that the whole charge is melted and non-contact retention is achieved by the Lorentz`s force. However, when the vacuum suction method or the tilting method is used to take out or pour a charge from the crucible, defects such as contamination due to contact with the wall and heat transfer are unavoidable. This report proposes a new pouring method using the electromagnetic force, providing the logical and experimental examinations. As a result of analysis of the electromagnetic force applied on the side of the charge levitating in the crucible, it was confirmed that changing the current value through the coil varies the pouring phenomenon, depending on the followability of the levitating position, and changing the relative position of the coil to the crucible enables pouring. Thus, the pouring form measuring method was established. 9 refs., 10 figs., 1 tab.

  17. Charging and discharging time control of electric vehicles for the purpose of load leveling; Fuka heijunka wo mokuteki to suru denki jidosha no juhoden jikan seigyo hosaku

    Energy Technology Data Exchange (ETDEWEB)

    Koyanagi, F.; Uriu, Y. [Seikei University, Tokyo (Japan)

    1998-05-01

    By ZEV regulation of the California government in 1990, not only the United States but also European countries and Japan are largely interested in replacing gasoline car by electric vehicle. Electric utilities expect that the electric vehicle improves the difference between the daytime and nighttime of a recent demand as a new market of electric power demand. There are some reports that indicates on the danger which generates the new peaks as the electric vehicles spread through the market in charging start hour. As the countermeasure for avoiding this problem, the authors propose that 1) inverse load flow by discharging of the contract private use EV is carried out as an energy shift in daytime, 2) the regional charging time shift method is introduced in the midnight charging time zone, in this paper. Therefore, the energy actual consumption of the automobile was investigated, and future demand was predicted by the mathematical consumption modeling. Especially, it is described a strategy of optimum introduction on scheme of effective electric vehicle for energy shift in section 2.2. And authors point out the necessity of market regulation for EV. 14 refs., 10 figs., 1 tab.

  18. Study on load levelling by means of the control of air conditioner operation; Kuchoki kado seigyo ni yoru fuka heijunka ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, H. [Hiroshima University, Hiroshima (Japan); Sadakuni, S. [Japan Broadcasting Corp., Tokyo (Japan)

    1995-04-20

    The recent drastic increase in the number of air conditioners has caused sharp and narrow peaks in summer seasons due to the inherent temperature sensitive characteristics. The authors proposed to reduce the peak power demand by controlling air conditioner operations, verifying its effectiveness on peak demand clipping. However, the former study has shortcomings in that any qualitative treatment of room temperatures or pleasant feeling was not attempted and it did not provide a way of assessing peak demand clipping in a power system as a whole. In this paper, we shall first propose a new control method that can compromise pleasant feeling and reduction in power demand. Although air conditioners are used to pursue `pleasant feeling`, this contradicts to reduce power consumption and further more the concept of `pleasant feeling` is very vague. Hence, `Weber-Fechner`s law` is utilized to quantify the pleasant feeling which is treated as fuzzy quantity. Fuzzy co-ordination method is used to compromise power demand curtailment and pleasantness. In the second part of this paper, we shall propose an approach of assessing the amount of peak load clipping when the newly proposed control strategy is adopted in a real size power system: A decrease in the required generation capacity is estimated provided that the Loss of Load Probability (LOLP) is maintained at the same level before and after the application of the new control strategy. The reduction can be regarded as a dividend of load management. 5 refs., 9 figs., 5 tabs.

  19. Application of adaptive control to windmill power system by computer simulation. Simulation ni yoru tekio seigyo no furyoku hatsuden system eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Tomiya, T.; Matsuo, T. (Anan College of Technology, Tokushima (Japan)); Suzuki, T.; Kamano, T. (Tokushima University, Tokushima (Japan). Faculty of Engineering)

    1991-07-20

    A windmill power system using load DC generators having resistive load was subjected to discussions by simulation on development of a control method and its output characteristics to draw out the wind energy effectively even when the system characteristics are unknown. The control method used is a mountaineering method available among adaptive control methods. As a result of discussions, the effectiveness of the mountaineering method was confirmed in controlling the output either when the wind velocity is constant or variable. With respect to the control interval, which is a problem in carrying out a control, it was found that the control output stabilizes as the control interval is increased when the wind velocity is constant, but takes longer time before reaching a steady state output. When the wind velocity is variable, the increased control interval reduces the output slightly because of the load resistance change becoming coarser. It was also revealed that, on simulated natural winds, this control method can draw out more energy than by a fixed load resistance. 7 refs., 11 figs., 1 tab.

  20. Development and application of controlled source audiofrequency magneto telluric method. Results of experiment at Akagi, Sakurajima, Kuju volcanos. Shingogen seigyo chijikichidenryuho (CSAMT-ho) no kaihatsuto oyo

    Energy Technology Data Exchange (ETDEWEB)

    Kusunoki, Ken' ichiro; Suzuki, Koichi

    1988-03-01

    Central Reserch Inst. of Electric Power Industry has carried out prospecting experiments, in various places, with magneto telluric method (MT method) which employs natural electromagnetic wave, and has confirmed the effectiveness of the method in estimation for location of faults, distribution range of rocks, and structure of geothermal sources. With increase in accuracy, the MT method, which was suitable for the approximate prospecting in wide areas, was considered to become useful for determination of detailed geothermal structures directly under prospective points of geothermal wells. For the increase in accuracy, it was necessary to increase the kind and intensity of electromagnetic wave. Consequently, we developed, first as domestically, an unit of controlled source audiofrequency magneto telluric method. The unit, generating artificially electromagnetic wave, is useful for underground structure prospecting. Fundamental experiment on transmission and reception of electromagnetic wave was carried out as preparations for full-scale prospecting, then the structures of volcanos were prospected resulting in the determination of thickness distribution of shirasu layers and heat transfer route from magma reservoirs up to ground surface. (19 figs, 11 refs)

  1. Improvement of adaptive fuzzy control for a photovoltaic/wind/diesel generating system; Taiyoko/furyoku/diesel hatsuden system no saitekigata fuzzy seigyo no kairyo

    Energy Technology Data Exchange (ETDEWEB)

    Nagaike, H; Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru National College of Technology, Kyoto (Japan); Kawamoto, T [Shizuoka University, Shizuoka (Japan).Faculty of Engineering

    1996-10-27

    The photovoltaic/wind/diesel generating system that uses a storage battery as auxiliary power has been proposed to supply power from the system to the independent area. In this system, it is important to generate no insufficient power from the viewpoint of effective energy utilization and minimize the fuel consumption of a diesel generator. Authors have proposed the adaptive fuzzy control that changes the shape of the membership function of input variables according to the parameter indicating the system state. However, a parameter was rapidly changed in the conventional method. This badly influences the control. Therefore, the way to determine the parameter that indicates the state of this system was improved. Assume that an input value is set to the average value between a certain point of time and the {Delta}t time as the method for determining a parameter. If the {Delta}t value is lower, the change in a membership function is more effective. As a result, a greater fuel reduction effect was obtained. 4 refs., 8 figs., 1 tab.

  2. On the muscle activity control in the hierarchy motor systems. Hierarchy undo system ni okeru kin no kassei seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Akiba, M.; Miyamoto, Y. (Osaka Industrial University, Osaka (Japan). Faculty of Engineering)

    1991-10-31

    Excitory impulses for motor systems are controlled by the psychophysiological nervous systems in the body either autonomically or voluntarily. Involved in the voluntary control loop are motor cortex, basal gangalia, thalamus, cerebellum, etc. The purpose of this study is to confirm whether it is possible to reduce or emphasize the muscle contraction voluntarily through electromyogram (EMG) feedback training. EMG can indicate the excitory impulses of motor units. In the experiments, electrodes were placed on the skin above muscles. A significant reduction effect was observed for subjects trained in relaxation of the forehead musculature through EMG feedback. Results of the experiments suggested that biofeedback training for relaxation of the forehead tensional muscle might be effective in eliminating muscle contraction, and that feedback training for activation of damaged muscles might be effective in emphasizing muscle contraction. 4 refs., 9 figs.

  3. Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, H; Sona, S; Koike, H; Hori, H; Negishi, N; Kohara, H; Ibusuki, A [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A; Borovkov, V [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

  4. Study of shift shock reduction of an automatic transmission using robust control; Robust seigyo wo mochiita ido hensokuki no hensoku shock teigen ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, K [JATCO Corp., Shizuoka (Japan); Totsuka, H; Sanada, K; Kitagawa, A [Tokyo Institute of Technology, Tokyo (Japan)

    1997-10-01

    To effectively reduce shift shock of an Automatic Transmission, we designed a feed-back controller that manipulates the hydraulic pressure of a clutch and input torque, and also controls the turbine revolution and output torque. We used robust control theory to consider the fluctuation of hydraulic characteristics and friction elements, and verified the effect of the controller by simulation and experiment. 1 ref., 11 figs.

  5. Comprehensive and Critical Literature Review on Insitu Micro-Sensors for Application in Tribology

    Science.gov (United States)

    1994-04-01

    Tsugai, Masahiro; Bessho, Mikio ; Araki, Toru; Onishi, Masayoshi; Sesekura, Takashi Source: SAE Technical Paper Series. Publ by SAE, Warrendale, PA, USA...MONITORING OF HYDROGEN ASSISTED CRACKING OF LOW ALLOY STEEL. Author. Hayashi, Yasuhisa; Takemoto, Mikio Source: Boshoku Gijutsu/Corrosion Engineering v...METALS AND ITS APPLICATION TO AE SENSOR. Author. Shimizu, Hiroshi; Watanabe, Hiroshi; Sato , Michio Source:. Japanese Journal of Applied Physics, Supplement

  6. JPRS Report, Science & Technology, Japan: Symposium on Applications of Advanced Technology: Sensors

    Science.gov (United States)

    1992-03-02

    Tokyo SENTAN GIJUTSU OYO formation of amphipathic cellular membrane compo-SYMPOSIUM in Japanese 3 Sep 91 pp 37-45 nents of procaryote , rhamnolipids A...rhamnolipid has a nonionic sugar part and an anionic cellular liposome as the matrix lipid of a biological film, carboxylic group as the hydrophilic...the phospholipids of bacterial 3. Liposome Sensor cellular membranes have no phosphatadyl choline and consist mainly of phosphatadyl ethanolamine, 4

  7. FY 1999 report on the results of the experimental verification and assessment on the establishment of a centralized load control system. Experimental verification on the establishment of a centralized load control system; 1999 nendo fuka shuchu seigyo system kakuritsu jissho shiken system no shiken hyoka. Fuka shuchu seigyo system kakuritsu jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The indirect load control system appropriately supplies information on the state of electricity use, peak adjustment financial incentive, etc. through TV at users. The direct load control system controls air conditioner by radio from control station. The indirect/direct load control effect per user in peak zone of a week day at 15:00 at highest temperature of 30 degrees C or more is 80-100W, which is equivalent to 13% of the electric power consumption. A certain effect was verified. The use of electricity with ideas has been settled consciously, and the continuity of action and consciousness is recognized. When hot days at highest temperature of 30 degrees C or more last, the rate of users which use electricity with ideas decreases, and the control effect becomes lower. As a result of having supplied on a day at highest temperature above 30 degrees C the information on energy saving different from usual, the higher control effect than usual was acquired. It will continue to the certain and effective control to effectively make the direct control which is not dependent upon actions of users such as the supply of information different from usual at the time of the continued unusual summer heat and the increasing demand for air conditioner, and the control of air conditioner focussing on a certain time. (NEDO)

  8. Study of QoS control and reliable routing method for utility communication network. Application of differentiated service to the network and alternative route establishment by the IP routing protocol; Denryokuyo IP network no QoS seigyo to shinraisei kakuho no hoho. DiffServ ni yoru QoS seigyo no koka to IP ni yoru fuku root ka no kento

    Energy Technology Data Exchange (ETDEWEB)

    Oba, E.

    2000-05-01

    QoS control method which satisfies utilities communication network requirement and alternative route establishment method which is for sustaining communication during a failure are studied. Applicability of DiffServ (Differentiated Service), one of the most promising QoS control method on IP network and studying energetically in IETF WG, is studied and it is found most application used in the utility communication network except for relaying system information could he accommodated to the DiffServ network. An example of the napping of the utility communication applications to the DiffServ PHB (Per Hop Behavior) is shown in this paper. Regarding to the alternative route, usual IP routing protocol cannot establish alternative route which doesn't have common links and nodes in their paths for a destination. IP address duplication with some modification of routing protocol enables such alternative route establishment. MPLS, distance vector algorithm and link state algorithm are evaluated qualitatively, and as a result, we found MPLS is promising way to establish the route. Quantitative evaluation will be future work. (author)

  9. FY 1999 report on the experimental verification on the establishment of a centralized load control system. Survey of safety of the commercialized system; 1999 nendo fuka shuchu seigyo system kakuritsu jissho shiken jitsuyo system anzensei chosa. Fuka shuchu seigyo system kakuritsu jissho shiken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of leveling load for the residential electric power demand, technical standards for the indirect load control system were studied in FY 1999. As to the systematization of safety standards, made clear were technical standards, items for experiment, etc. for the user equipment monitor control system trially developed/manufactured. Namely, those are tests correspondent to technical standards of electrical appliances, tests on the influence of external agitation, etc., measurement of the leakage electromagnetic field amount, etc. In the study of the energy use optimization support, concepts for optimization were comprehensively asked by the effective air conditioner operation method and from the state surrounding users. Studies were made of effects of the air conditioner control, indices of assessing amenity of users which becomes factors to promote the centralized load control. In the study of the optimum in-house communication method, made were the confirmation of effectiveness of the power-line carrier transmission method, future outlook using other communication technologies, and evaluation of economical efficiency. As to the enhancement of communication reliability, the effectiveness of measures for improvement by alteration to a multi-carrier system transceiver which realizes improvement of the basic performance of equipment was recognized beside the addition of LC circuits which are aimed at improving the communication environment. (NEDO)

  10. Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; O2/CO2 combustion technology; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu (sanso nensho gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the purpose of developing combustion systems in which environmental pollutants are less emitted from coal-fired boilers, conducted in fiscal 1994 were a study of load followability of oxygen producing equipment, and element and basic tests on oxygen combustion systems. Dynamic simulations were made to confirm load followability of low-purity oxygen producing equipment. Further, a test was made on starting time of oxygen producing equipment. As a result of the simulation, favorable load followability was confirmed except for some of the process. The width of variation of the product oxygen purity was {plus_minus} 0.7% at maximum. In the element test on oxygen combustion systems, an experiment on the oxygen combustion using pulverized coal was conducted to study heat collection characteristics of furnace and response to multi-kind of coal. A study of balance of S content, experiments on characteristics of crushing/transporting pulverized coal, etc. were added. There were seen no peculiar differences in CO2 transport and air transport. 216 figs., 31 tabs.

  11. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  12. Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; topping cycles; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu bun`ya (topping nensho gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    As a realistic measure to reduce environmental pollutants emitted from coal-fueled boilers, a developmental study was conducted of high-efficient combustion systems. In fiscal 1994, four types of topping cycles which are different in system structure and gasifier type were selected, and topping cycles assuming a 300MW-class power plant were trially designed. Further, an evaluation of adaptability of these systems was made, and an selection of the optimum system for the early development was made among the systems. As a result, the evaluation was obtained that `a system using air blown gasifier` is most suitable for conducting the next-stage research. In the element test on the topping combustion technology, collection was made of data of desulfurization activity, desulfurization oxidation mechanism and alkali metal behavior at the laboratory level, data of temperatures and gas concentration distribution in coal gasification, data of simulation of the gasifier reaction, and the other data. 262 figs., 66 tabs.

  13. FY 1998 annual report on the research and development of non-linear, opto-electronic materials; 1998 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The final assessment of researches on non-linear, opto-electronic materials was conducted in FY 1988. These researches are evaluated as the world-level basic researches, high in potential of giving ripple effects on various areas. The R and D themes are organic, low-molecular-weight materials; technology for orientation-controlled crystal growth; conjugated polymer films; microcrystallite-doped glasses using vapor deposition and stuffing method; glass composite materials using sol-gel method and ultra-low melting point glass; nanoparticle-dispersed glasses using super-cooling technology; materials dispersed in organic compounds; organic superlattice formation; three-dimensionally superstructured materials; and comprehensive surveys and researches. The researches and surveys on the common basic techniques were recommissioned to Universities of Tokyo, Keio Gijuku, Nagoya, Tohoku and Hokkaido. These themes are analytical methods for non-linear optical characteristics; morphology-controlled crystal growth of nonlinear-optical organic materials and fundamental studies on all-optical devices; large enhancement of optical nonlinearity and its mechanism in nanocrystals embedded in matrices; improvement of organic materials for high performance; and ultrafast nonlinear optical processes and their application for controlling ultrafast optical pulses. (NEDO)

  14. Study on the creation of inorganic materials using micro-gravity environment; Bisho juryoku kankyo riyo muki zairyo no sosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Creation of new functional inorganic materials using micro-gravity environment was studied. Observation of an electrode interface phenomenon under micro-gravity clarified that time variation in interference fringe is dependent on current density and electrode thickness in ground experiment, while it is dependent on not electrode thickness but current density under micro-gravity. In fabrication of glass fine particles under micro-gravity, true spherical glass fine particles of 4-7{mu}m in size were obtained corresponding to a charge of 40mg by evaporation and solidification of sodium tellurate glass as raw material under micro-gravity. In fabrication of non-harmonic Pb-Zn system alloy, the homogeneous alloy texture of 5{mu}m level was observed which has never been observed in previous metal phase diagrams by fusion of 80atom%Pb-20atom%Zn mixture under micro-gravity and quenching from 500degC. On the study on fabrication of spherical semiconductor crystals, 7 spherical Si single crystals of 300{mu}m in size were obtained. 12 refs., 48 figs., 2 tabs.

  15. Achievement report for fiscal 1998. Research and development of advanced functional materials designing platform; 1998 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Stated in this paper are the reports of the working groups (WGs) for the above-named endeavor and the reports on the achievements of the universities to whom the jobs had been commissioned. WG1 carried out research and development related to the coarse-grained molecular dynamics method. WG2 dealt with mesoscale structures, which are quite larger than atoms, such the phase separated structure of polymer molecules and interfacial structures, worked for the construction of a general-purpose simulator system for reproducing/predicting their dynamic properties, and studied the properties of polymers by use of the said simulator system. WG3 worked on polymeric phenomena large in scale in terms of both space and time. Faculty of Engineering, Yamagata University, constructed a materials physical property database necessary in designing materials by simulation. Institute of Industrial Science, Tokyo University, studied the viscoelastic phase isolation at the quantitative level. Tokyo University's Faculty of Engineering-managed study teams investigated the nano-scale structures and properties of polymer materials. Faculty of Engineering, Tokyo Institute of Technology, performed research and development about the meso-scale behavior of multi-constituent polymers. (NEDO)

  16. Investigational study of optical function materials for two-dimensional data processing; Nijigen joho shoriyo hikari kino zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper investigated/studied `space light modulation materials,` `dynamic hologram/memory materials,` `optical waveguide path materials,` etc. which become key materials in the high speed two dimensional processing. As to electrooptical materials proposed in this investigational study, the external electric field and the electric charges generated make quality of molecules themselves directly change to memory strong/weak signals of light. Therefore, the response velocity becomes less than a millionth of that of the liquid crystal display, and high speed which is needed for realtime moving image processing is anticipated. Hologram includes the phase information in addition to information on light strength. Therefore, it is a large capacity record medium and at the same time a record medium which can read/write two dimensional information as it is. With optical fiber, images cannot be transmitted as they are. Light waveguide path materials are those that accumulate roles of mirror and lens in a sheet of the material and construct a system which is strong in vibration, as optical parts connecting among materials for two dimensional data processing. 273 refs., 107 figs., 17 tabs.

  17. Simulation on breakage of heterogeneous materials caused by detonative loading; Bakugo shogeki ni yoru fukinshitsu zairyo no hakai gensho no simulation

    Energy Technology Data Exchange (ETDEWEB)

    Sassa, K; Watanabe, T; Ashida, Y [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-05-01

    Investigations were conducted by simulation of breakage of inhomogeneous materials (rock) attributable to detonative loading, which simulation used the Days-2 Code. During the simulation, one-free-face blastings were used for testing a homogeneous structure, horizontal 2-layer structure, and horizontal 3-layer structure. Property values were assigned to the rocks on the assumption that they were sedimentary rocks such as sandstone or mudstone or hard rocks such as granite. As the result, it was found that a detonative loading resulted in shear failure in a sphere near the focus that was followed by radially developed cracks due to tension breakage, that more area is damaged in a soft rock than in a hard rock, that cracks due to breakage are produced by the overlapping of waves directly from the focus and those reflected from the free face in case of one-free-face blastings, that such cracks propagated along the soft rock layer in case there is a soft rock layer in a hard rock, but that breakage does not extend beyond the soft rock layer. 6 refs., 6 figs., 1 tab.

  18. Development and application of corrosion and protection database using intranet; Intoranetto wo riyo shita zairyo fushoku detabesu no kochiku to katsuyo

    Energy Technology Data Exchange (ETDEWEB)

    Futatsugi, Takashi.; Baba, Fumio.; Suzuki, Tsuguo. [Ajinomoto Co., Inc., Tokyo (Japan). Technology and Engineering Laboratories

    1999-05-15

    A new corrosion and protection database system, which stores a large amount of documents and informations about corrosion and protection, such as case histories, materials data, fabrication methods and repairing methods, has been developed. Users of the database system can be accessed using WWW browser via Intranet. This database can be operated by easy handling with only click and drug. The database system is expected to offer a wide knowledge for corrosion related engineers and to decrease corrosion troubles. (author)

  19. Achievement report for fiscal 1990 on research and development of photoreactive materials; 1990 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Activities were performed with an objective to establish fundamental technologies related to photoreactive materials capable of ultra-high density and high resolution indication by controlling structures and assemblies of molecules by using light. The activities were taken in the four fields of elucidation of photoreactive mechanisms and fundamental properties, development of the materials, material processing and constituting technologies, and evaluation technologies. Specifically speaking, the activities were developed on the multiplexing technology applicable to ultra-high density recording, sensitivity responsiveness, and material stability in photochromic materials and photochemical hole burning (PHB) materials. For the photochromic materials, development was performed on photochromic materials to form associations, and on a thin film forming technology by means of the organic molecular beam epitaxial process. For the PHB materials, research was implemented on use of the materials at elevated temperatures, development was made on quinone-based materials, research on enhancement of multiplexity, development on porphyrine-based materials, and research on the organizing technology. In the research of the use at elevated temperatures, development was progressed on a material that can retain under the liquefied nitrogen temperature the status of wavelength multiplexed recording that has been formed under the liquefied helium temperature. (NEDO)

  20. Evaluation report on the development of ultra-solid lubricant with cluster diamond; Cluster diamond wo riyoshita kotai junkatsu fukugo zairyo no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The fiscal 1998-2000 results of efforts to develop cluster diamond (CD)-diffused solid lubricant composite materials expected to exhibit excellent lubrication are stated. Since friction greatly affects machine life and energy efficiency, friction reduction is an important task. Very hard and microscopic CD was utilized for the achievement of a friction coefficient of 0.08. A manufacturing technology for molds 10nm or smaller was developed, which enabled the development of a gear not larger than 8mm. The success will enable the operation of micromachines in the absence of lubrication which is impossible at present. A CD-aided functional layer creation technology was also developed. It is expected that the development and practical application of micromechanisms will make rapid progress in the 21st century. Much is expected from the creation, and goods with the achievement applied thereto, of advanced technologies whereinto non-lubrication, functional layer creation, and excellent heat conductivity are incorporated. It is quite significant that, since CD is available in any field as far as light-load low-speed sliding conditions are satisfied, sliding parts will be improved and service life will be prolonged. (NEDO)

  1. Effects of mechanical stimulating treatment on self-organization phenomena of materials; Kikaiteki reiki shori. Zairyo no jiko soshikia gensho ni oyobosu sono koka

    Energy Technology Data Exchange (ETDEWEB)

    Hida, M. [Okayama University, Okayama (Japan). Faculty of Mechanical Engineering

    1999-03-31

    The atoms and atom clusters around dislocation cores in crystals or surface layer deformed by mechanical energy are locally excited so as to give rise some chemical reactions and to self-organize their products into a kind of Spatial-Temporal Pattern Formation as a dissipative structure. A famous coupling phenomenon between mechanical and chemical process in solid materials must have been mechanical alloing. This report explains that various mechano-chemical treatments are powerfull method for entraining the solid system into non-equilibrium states and interesting phenomena stimulated by the mechanical self-catalysis reaction causing self-organization. (author)

  2. Development of new type of nonlinear optical materials with a function of ultrafast optical modulation; Chokosoku hikari reiki hencho kino wo motsu atarashii hisenkei kogaku zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakaguchi, H. [Shizuoka University, Shizuoka (Japan). Research Institute of Electronics

    1995-12-15

    Ultrafast modulation of second harmonies from a Langmuir-Blodgett film consisting of a ruthenium complex was demonstrated for the first time. The mechanism of the modulator of SHG intensity on laser irradiation was ascribed to the change of molecular hyperpolarizability of the ruthenium complex on going from the ground state to the excited state. 9 refs., 12 figs.

  3. New carbon materials. Recent advances in the synthesis of fullerenes and carbon nanotubes; Shin tanso zairyo. Furaren, kabon nanochubu no gosei no saikin no shinpo

    Energy Technology Data Exchange (ETDEWEB)

    Yumura, M [National Inst. of Materials and Chemical Research, Tsukuba (Japan)

    1996-01-01

    Arc synthesis method, which is now the center for the synthesis of new carbon compounds such as carbon nanocapsules and carbon nanotubes, is introduced together with its current status. Many new carbon compounds are synthesized by DC arc discharge heating method (arc discharge method) in which a graphite bar is used as the electrode. C70 and higher order fullerenes having larger carbon numbers are found one after another in the soot produced by the arc discharge method, and the structures of C76, C78, C84, C90, C94, and others have been clarified. It is considered in the arc discharge method that the processes of a large amount of carbon evaporation by high temperature and the succeeding quenching cause to produce various kinds of new carbon compounds. In connection with other synthesis methods, synthesis of fullerenes by incomplete combustion, synthesis of nanotubes by the vapor phase thermal decomposition method, and the synthesis of nanotubes using casting molds are discussed. 24 refs., 6 figs.

  4. Effect of additives in the baking of electrolytic materials for SOFC; SOFC yo denkaishitsu zairyo no shoseiji ni okeru tenkabutsu no koka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, H. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1998-09-10

    A technique is discovered for improving on the baking properties of cerium oxide which is one of the solid electrolytic materials for SOFC (solid oxide fuel cell). Cerium oxide, samarium oxide, and gallium oxide are weighed, each to the specified element ratio. The element ratio of cerium is fixed at 0.8 against the other elements except oxygen, and the element ratios of samarium or gallium are caused to change. Specimens containing gallium are designated as CSGa, those not containing as SDC. SDC baked at 1600degC and CSGa (1%) baked at 1450degC are similar to each other in terms of average grain diameter. Specimens with gallium added thereto can be baked at temperatures that are lower than these by approximately 150degC. The conductivity of CSGa (0.2%) baked at 1500degC is higher than that of SDC baked at the same temperature, and is similar to that of SDC baked at 1600degC. Baking is enhanced by the addition of 0.2% gallium. In the domain where more than 1% of gallium is in presence, conductivity lowers with an increase in the amount of gallium added. The conductivity of CSGa (1%) baked at 1450degC is similar to that of SDC baked at 1600degC. 4 figs., 1 tab.

  5. Fiscal 1994 technological survey report. Research study on polymer materials by precision polymerization; 1994 nendo seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In the paradigm that propelled polymer chemistry, there are involved the establishment of polymer concept, engineering plastics, regulation of higher ordered structure, and precision polymerization. The first two produced the polymer chemistry era in the 20th century. The regulation of higher ordered structure and the precision polymerization are the fundamental technologies supporting the polymer chemistry of the 21st century. The precision polymerization is a technology for regulating the stereospecificity, sequential structure, and molecular weight of polymers by regulating atoms and molecules and is referred to the following important techniques to be concrete. In the precision addition polymerization, stereospecific regulation and purification of active site to give living polymers are required while, in the precision condensation polymerization, regulation of condensation probability process to be secondary Marcov chain is necessary, as is the establishment of non-defect condensation condition avoiding high temperature deterioration and the like. In the biomimetic precision polymerization, key issues are the method of incorporating molecular recognition control and sequential structure control by living organs into an industrial process. If the higher ordered structure can be regulated by the precision polymerization, it is possible to obtain numerous high performance/high functional materials such as superconductors. (NEDO)

  6. FY 1991 Report on the results of the researches on nonlinear photoelectronic materials; 1991 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    The nonlinear optics with light-light conversion and electro-optical effects are expected to be the optical materials of the next generation for their functions of, e.g., conversion of the infrared laser beams into visual light, and optical switching. The efforts are directed to development of the procedures for exploring and designing various raw materials, and technologies for synthesizing the raw materials and for producing and evaluating the materials, in order to develop highly nonlinear, high-speed responding materials. Three areas are studied; for the organic materials, the chiral nonlinear effects are demonstrated and the new procedure for determining electrical susceptibility ({gamma}) is developed; for the dispersed materials, highly nonlinear susceptibility of glass dispersed with fine particles of semiconductors, e.g., CuCl, is realized, and possibility of controlled dispersion of fine semiconductor particles in an organic polymer is established; and for development of the superlattice-based materials, the layered structures of thin organic superlattice films are studied, the thin semiconductor films of high purity and little defects are prepared, and development of the three-dimensional structures is started. The individual researches are conducted, 3 for the organic materials, 4 for the dispersed materials, and 2 for the superlattice-based materials. The targets of susceptibility and response are 10{sup -8}esu or more and 10ps or less, respectively. (NEDO)

  7. Study on low permeable backfill materials. Backfill materials for waste disposal facilities; Koshisuisei juten zairyo ni kansuru kenkyu. Hoshasei haikibutsu shobun shisetsu eno tekiyosei kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shiraishi, F; Konishi, M; Shiraishi, H [Okumura Corp., Osaka (Japan)

    1994-11-15

    A discussion was given on the fundamental properties of mortar made from cement mixed with silica fume. Four kinds of silica fumes with different particle size distributions were used. The following results were obtained: distribution of pores in mortar admixed with silica fume shifts to the smaller radius side; while the admixture increases the compression strength in mortar, the increasing trend varies depending on the kinds of silica fumes; this is thought to be caused from the difference in pozzolan activity between silica fumes; and the strength increase is caused by densification of the structure due to the pozzolan reaction that is generated after hydration, or in other words, decrease in the pore volume. The applicability of the mortar was investigated as a filling mortar to fill up clearances between wastes. It was found that the filling performance can be controlled by mixing silica fume at an adequate level and adjusting the viscosity. The diffusion coefficient for the admixed concrete is smaller by 30% to one digit than that for the ordinary concrete. High-performance water stopping concrete of 0.11 {times} 10{sup 4}cm {sup 2}/s at maximum was obtained. The concrete can be regarded as a material having superb filling and water stopping performances. 6 refs., 4 figs., 5 tabs.

  8. Ultraviolet rays hardening type material which can do the repair of FRP it is easy; Kantan ni FRP no hoshu ga dekiru shigaisen kokagata zairyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-15

    The seat-shaped ultraviolet rays (UV) hardening type material which the reinforcement of the fiber strengthening plastic (FRP) and the repair and the corrosion partial repair of the steel rice are made easily in is developed, is sold in late April. The same product is the seat, which made soak an UV hardening type plastic in the fiberglass. Though a un-saturation polyester plastic was adopted, as for many FRP repair materials, a tolerance to the medicine, shock, heat rose by adopting plastic, and the adhesion power became strong, too. And, because it is a seat-shaped, a hand lei rise which takes a plastic and hardening medicine in its hand and to mix is compared with the way of repairing it, and the strength of the repair point becomes uniform with constructing it easily in a short time, too. The car and the port business world are wide except for the construction, and the same company plans sales promotion. (translated by NEDO)

  9. Preprint of the 40th material study joint lecture of Science Council of Japan; Dai 40 kai Nippon gakujutsu kaigi zairyo kenkyu rengo koenkai maezurishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-19

    The paper stated mostly topics from special lectures. Composite materials have a lot of potentialities, and there are larger expectations in flexible and high-strength soft composites rather than the conventional high rigidity ones. As to micro-machines, the problems are on mechanical property of the element, environment/friction/fracture/life, etc. and the evaluation method of the characteristics was studied. Concerning the research and development of the intellectual structure system, the introductive study has entered the second year. Ultimately, structures have functions similar to those of the living organism had, and conduct self-diagnosis, self-repair and autonomous-response. Railroad structures receive regular inspections according to the rule, and a half of the objects for the inspection are cracks, unbonding and weathering of concrete. With the Hanshin Awaji great earthquake especially, the anti-earthquake reinforcement has been expedited. In various kinds of materials, the finer the crystal particle becomes, the greater the high temperature deforming ability becomes. When the particle size is below the critical particle size, it shows superplasticity. The study is advancing. As to high density secondary batteries, introduced especially were Ni-hydrogen batteries and Li batteries.

  10. Achievement report on research and development in fiscal 1989. Research and development of non-linear photoelectron materials; 1989 nendo hisenkei hikari denshi zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective to realize the communication and information processing utilizing the high velocity and parallelism of light, search for materials having non-linear susceptibility and high-speed responsiveness, and research and development of the material using technology have begun. This paper reports the achievements in fiscal 1989. In developing organic materials, investigations and preliminary experiments were performed on three-dimensional non-linear photoelectron materials of organic low molecular systems, such as chiral non-linear photoelectron material. Fundamental studies were made on growth of orientation controlled crystals. Researches were carried out on polymeric films of organic and conjugate systems. In developing the dispersed system materials, researches were executed on a technology to deposit CuCl particulates using the air phase method and porous glass impregnation method, and on evaluation of non-linear photoelectron properties of CuCl particulate dispersed glass. In addition, glass dispersed system materials were studied by using the sol-gel method, the ultra-low melting point glass method, and the ultra quenching method. Furthermore, for the organic dispersed system materials, synthesizing conditions were discussed on CdS/polymer dispersing element films, and ultra-particulate synthesizing experiments were performed. In developing the ultra-grid system materials, researches were performed on the organic ultra grid making technology and the three-dimensional ultra-structuring technology. (NEDO)

  11. Development of new engine bearings with overlay consisting of solid lubricants; Kotai junkatsu overlay tsuki engine yo suberi jikuuke zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kanayama, H; Kawakami, S; Gohara, C [Taiho Kogyo Co. Ltd., Aichi (Japan); Fuwa, Y; Michioka, H [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    Recently, modern engines have a tendency for higher output and longer periods. As a result , higher bearing performance is required. For this reason, we have developed the new conceptual overlay consisting of solid lubricants and thermosetting plastics. This paper describes the performance of engine bearings with the new overlay. 5 refs., 13 figs., 5 tabs.

  12. FY 1991 Report on the results of the research and development of photo-reactive materials; 1991 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    This project is aimed at establishment of the basic technologies for photo-reactive materials capable of, e.g., superhigh-density, superhigh-resolution display using photo-functions to control structures and associated conditions of the molecules. More concretely, the efforts are directed to realization of the technologies for multiplexing, sensitivity-response and material stability, applicable to superhigh-density recording by photochromic and photo-chemical burning (PHB) materials. For the photochromic materials, the long-chain alkyl derivatives of photochromic compounds, e.g., spiropyran and fulgide, are formed into thin films by the LB method, in order to develop organic, superhigh-density recording devices by controlling their associated conditions, and controlling of the photochromism reactions in the films is studied. Those studied for the PHB materials include improvement of heat resistance of the materials, development of quinone-based materials and improvement of their degree of multiplexing, and development of porphyrin-based materials and of technologies for structuring them. The comprehensive survey/research activities include extraction of the problems involved in the themes mainly related to the committee activities, and related technologies. (NEDO)

  13. On the improvement of mechanical properties of monolithic silica aerogels (for transparent insulating material); Silica aerogel (tomei dannetsu zairyo) kyodo no kaizen ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Tajiri, K; Igarashi, K; Tanemura, S [National Industrial Research Institute of Nagoya, Nagoya (Japan)

    1997-11-25

    Study was made on improvement of the strength of silica aerogel as transparent insulating material. Silica aerogel is a low-density porous material with high heat insulation and transparency. To develop a insulating material with high transparency, monolithic silica aerogel was studied. For direct use of it for windows, its strength improvement was attempted. The aerogel was prepared by supercritical drying (alcohol or CO2) of silica wet gel obtained by hydrolysis and condensation of silicon alkoxide solution. To prepare the aerogel bonded on plate glass for strength improvement, the aerogel was bonded to alkoxide by exposing active silanol radical through F-etching of plate glass surface. However, to obtain the practical large-area bonded aerogel, shrinkage control of the aerogel in supercritical drying was necessary. Addition of Laponite into a silica network for strength improvement by polymer increased the bending strength by 50%. Although some reduction of its transparency was observed because of clouding, its heat insulation was stable. Further strength improvement is necessary for its practical use. 5 figs., 1 tab.

  14. Fiscal 2000 survey report. Research on creation of microspheric photonic material; 2000 nendo bishokyu photonics zairyo no sosei ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Experiments were conducted under microgravity for findings on the creation of microspheric photonic materials which are high in sphericity. The experiments were carried out at the fall type microgravity facility of Japan Microgravity Center (JAMIC). In the experiments on the ground surface and under microgravity, glass specimens of 3BaO-97B{sub 2}O{sub 3} mol%, 4BaO-96B{sub 2}O{sub 3} mol%, and 2SrO-98B{sub 2}O{sub 3} mol% were tested. They were heated, melted, and cooled for the on-site observation of phase splitting in them. It was found as the result that, in the case of specimen 3BaO-97B{sub 2}O{sub 3}, the phase splitting start under microgravity was similar to that on the ground surface while the nucleation velocity was lower under microgravity. Specimen 2SrO-98B{sub 2}O{sub 3} mol% exhibited an approximately 0.5-second delay in its phase splitting start under microgravity as compared with its ground surface behavior. As for the nucleation velocity under microgravity, the value was same as that on the ground surface in the first half but, in the second half, it was lower than that on the ground surface. The said approximately 0.5-second delay in the phase splitting start was, when the cooling rate was taken into consideration, attributed to an approximately 6.5 degrees C fall in the phase splitting start temperature, and this suggested that phase splitting was suppressed under microgravity. (NEDO)

  15. FY 1985-1992 summarized report on the R and D of photoreactive materials; 1985 nendo kara 1992 nendo hikari hanno zairyo kenkyu kaihatsu sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-01

    For the purpose of establishing the basement technology relating to photoreactive materials which make remarkably higher density and larger capacity of the information recording possible, the following were made for photochromic materials and PHB materials: elucidation of the photoreaction mechanism, development of materials, development of material processing/structure technology and development of evaluation technology. The target is to establish the technology of the multiplex recording which is applicable to the super-high density recording in relation to PHB materials/organic photochromic materials which have potentiality of photon-mode recording. PHB materials were developed which have potentiality of 600 wavelength multiple recording and 5 electric field multiple recording in 4.2K and 9 wavelength multiple recording in 77K. Photochromic materials were developed which have high sensitivity and preservation stability and have potentiality of 10 wavelength multiple recording at room temperature. A new photo-recording method was found out by which the orientation of liquid crystal is photo-controlled and potentiality of the multiple polarization was shown. Moreover, the fabrication was successfully made of PHB materials and photochromic materials which make non-destructive readout operation of more than 10{sup 4} times possible. (NEDO)

  16. Characteristics of radiation temperature and radiosity coefficient by means of infrared radiometer. Sekigai hoshakei ni yoru zairyo hyomen no hosha tokusei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Okamoto, Y; Kaminaga, F [Ibaraki University, Ibaraki (Japan). Faculty of Engineering; Ishii, T; Sato, K [Ibaraki University, Ibaraki (Japan); Kurokawa, T [NEC San-ei Instrumentsu Ltd., Tokyo (Japan)

    1991-12-25

    A radiation thermometer was applied to the measurement and analysis of radiation temperature of the material surface. In this paper, the characteristics of the radiation temperature and the radiosity coefficient of gray body materials are investigatied. An infrared radiometer was used, which detects radiation energy in the region between 8 and 13{mu}m of wavelength. This infared radiometer has a Hg-Cd-Te photon radiation sensor. The variation of emissivity was measured for the four kinds of non-metalic materials, i.e., graphite, carbon fiber composite, Si-SiC ceramic, and black paint spread on an aluminum plate. As a result, the relationship between material temperature and radiation energy was made clear. Furthermore, the space-dependent variation of the radiation temperature and the radiosity coefficient was derived from the two-dimensional CRT image of the infrared radiometer. Consequently, the emmisivity variation gave a maximum for the carbon fiber composite surface rich in irregularity, and decreased in the order of graphite, Si-SiC, and black paint. 7 refs., 15 figs.

  17. Achievement report for fiscal 1990 on research and development of highly crystalline polymeric materials; 1990 nendo kokesshosei kobunshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Activities were performed to seek polymeric materials having mechanical strength comparable to metallic materials as a result of giving contrivance on the composition and processing method, and bending strength of 100 GPa or more. The activities were taken in the following five fields: (1) a one-dimensional system material, (2) special melting and forming of a multi-dimensional system, (3) compound forming of multi-dimensional molecules, (4) hybrid cross-linking of cross-linking systems, and (5) high-density cross linking of cross-linking systems. In Item (1), researches were made on optimization of the structures, and elongation and fluid processing of thermotropic liquid crystal polyacrylate, wherein the objective was achieved. In Item (2), the objective was achieved on poly (imide-benzobisthiazole) by monoaxial drawing and lamination thereof. Discussions were given on the liquid crystal polymer as to its correlation between the structure and the magnetic field orientation. In Item (3) discussions were given on the composition and processing method for molecule compounded materials reinforced by aromatic polyamide matrix-polyphenylenebenzothiazole. In Item (4), ionomers were discussed. In Item (5), discussions were given on multi-functional diacetylene system and diacetylene group containing polyimide. (NEDO)

  18. Achievement report for fiscal 1990 on research and development of electrically conductive polymeric materials; 1990 nendo dodensei kobunshi zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    It is intended to realize new electrically conductive materials characterized by light weight, corrosion resistance and easy-to-process performance, and electrical and electronic materials having functions different from those of metallic conduction mechanism. Therefore, activities were performed to seek technologies for polymeric materials having conductivity greater than 10{sup 5} S/cm and being stable and easy to process. Activities were taken in the following six fields: (1) new hydrocarbon conjugate polymers, (2) excipient conjugate conductive materials, (3) technologies to form thin films of graphite synthesized at low temperatures, (4) conductive polymers of hetero aromatic system, (5) research and development of conductive materials of the hetero containing system and the {pi} conjugate system, and (6) comprehensive investigative research. In (1), thin films of polyacetylene and polyacene systems were formed, in (2), excipient hydrocarbon conjugate polymers and excipient graphite materials were developed, in (3), a high-accuracy process controlled graphite thin film forming technology was developed, in (4), the conductivity was enhanced by using high-order structural control and molecular design, and stability of the conductive polymers of complex annular conjugate system was enhanced, and in (5), conductive polymers of the hetero containing system and the {pi} conjugate system, and flexible graphite fibers were developed. (NEDO)

  19. Report on investigations and studies on development of materials for hydrogen absorbing alloys; Suiso kyuzo gokin no zairyo no kaihatsu ni kansuru chosa kenkyu hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper describes investigations and studies on hydrogen absorbing alloy materials and the technologies to utilize them. In the investigations and studies, literatures were collected and put into order, questionnaire surveys were performed and analyzed, lecture meetings and panel discussions were held, and the discussion results were summarized. In the present status of developing hydrogen absorbing alloys, the current status of and problems in developing such hydrogen absorbing alloys as Ti-based, Mg-based, and rare earth-based alloys were put into order. Discussions were given on prospects of possibilities of developing new alloys, making them amorphous, and putting them into mass production. In the current status of developing the utilizing technologies, such technologies as hydrogen storage systems and heat pumps were put into order and discussed. With regard to problems in hydrogen absorbing alloys, discussions were given on alloy weight, pulverization, activation, heat conductivity, and alloy costs. In discussing the safety, discussions were given on the safety and compliance with related laws and regulations relative to hydrogen transportation using a great amount of hydrogen absorbing alloys, their storage, and heat storage systems. In addition, questionnaire surveys were carried out with an objective to identify the status of developing hydrogen absorbing alloys and needs from the industries. (NEDO)

  20. Basic research on the development of 'intelligent-type' humidity control materials; Intelligent gata choshitsu zairyo no kaihatsu ni kansuru kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tomura, S.; Maeda, M.; Inukai, K.; Ohashi, F.; Suzuki, M.; Suzuki, K.; Shibasaki, Y. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

    2000-10-25

    The water vapor adsorption desorption isotherms of purified and/or synthesized sepiolite, allophane, diatomite, selectively leached kaolin and mesoporous silica were measured to develop humidity control materials in living environments. Based on Kelvin's capillary condensation theory, suitable pore diameters for controlling relative humidity at 40 and 70% were calculated to be 3.2 and 7.4 nm, respectively. Wakkanai diatomite, purified allophane, selectively leached kaolin and mesoporous silica have suitable pore diameters and high water adsorptivity, and were considered as candidates for humidity self-control materials. Among these materials, mesoporous silica formed as a tile showed the best performance as a humidity control material in desiccator and model house levels. (author)

  1. Achievement report for fiscal 1988 on fundamental technologies for next generation industries. Research and development on composite materials; 1988 nendo fukugo zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    With an objective to realize structural materials with light weight, high strength and high rigidity, research has been performed on composite materials. This paper reports the achievements in fiscal 1988. In the development on resin-based composite materials, the results of the evaluation tests on forming plates for epoxy-based resins were analyzed and summarized. On the polyimide-based resins, attempts were made on enhancement of formability of the terminal type and main chain type high heat resistant resins. Evaluations were executed on the resin characteristics by using the impact test, and heat deformation and heat reaction analyzing tests. Furthermore, experimental discussions were given on the heat transfer forming process, prefabrication forming process, microwave forming process, and hybrid forming process. In developing the metallic composite materials, the characteristics evaluation tests and manufacturing technologies were summarized on intermediate materials of the carbon fiber system and silicon carbide system. In addition, researches were performed on trial fabrication and formation of wire preforms. In the forming processes, discussions were given on the press forming process, roll forming process, HIP forming process, and thin wall thickness forming process. (NEDO)

  2. Research on giving antibacteria activity of tailored dental materials; Gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The secondary dental caries easily occur by breeding of bacteria in cavities between living body and composite resin, false tooth or root of tailored tooth as tooth repairing materials. The antibacteria activity of tailored dental materials was thus studied by implanting Ag ion. The antibacteria effect with time after culture of caries bacteria was studied by implanting Ag ion into SiO2 powder, PMMA samples and Ti alloy samples at 20 and 200keV in energy of ion. In addition, the antibacteria activity of SiO2 powder as composite material was found at 25keV which was previously effective for the antibacteria activity. This SiO2 filler (Ag{sup +} filler) showed the antibacteria activity on every bacteria sample after 2h, and in particular, could kill all of 3 kinds of bacteria obtained from a composite resin surface after 12h. The number of living S. salivarius was reduced by half after 12h. The application of the composite resin filler implanted with Ag{sup +} is significant to prevent recurrence of caries. 5 refs., 27 figs., 7 tabs.

  3. Development of nonlinear optical materials using inorganic-organic complexes; Hisenkei kogaku zairyo to shite no yuki-muki fukugotai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Mizuno, N. [Hokkaido University, Sapporo (Japan). Catalysis Research Center

    1994-12-15

    Development was attempted on organic-inorganic complexes as nonlinear optical materials. The objective is to develop elements with SHG activity (generating second harmonics) to change a visible ray into an ultraviolet ray by inserting P-nitroaniline (pNA) into such solid acids having strong static electric field as zeolite, laminar compounds, and heteropolyacid, and utilizing the static electric field and the molecule coordination field of inorganic compounds. Used for the pNA{center_dot}Bronsted acid composite are HBr, HCl, HNO3, and H2SO4. The pNA that has a center of symmetry in the crystalline structure and does not generate the second harmonics shows SHG when it is formed into a composite with HBr. No SHG is recognized in other acid composites. This difference is due to the difference in the crystalline structure. The SHG activity was generated when pNA is loaded onto alumina and silica as solid oxides. When zeolites are used as carriers, no SHG was observed. A composite of pNA{center_dot}AlCl3 has high SHG intensity, which reached a maximum when the pNA/AlCl3 ratio was two. This composite showed four new peaks that belong to the SHG activity phase. 8 refs., 2 figs., 2 tabs.

  4. Development of symmetric composition-gradient materials including hard particles in its surface layer; Hyosobu ni koshitsu ryushi wo fukumu taishogata sosei keisha zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of new materials with both thermal resistance and thermal shock resistance was studied on the basis of symmetric ceramics/metal/ceramics gradient composition. Al2O3/TiC/Ni/TiC/Al2O3 was used as material model of basic composition, and the system was selected where WC-Co system alloy hard particles were dispersed into the Al2O3 ceramic surface layer. The layered material was sintered in N2 gas atmosphere by SHS/HIP method using exothermic caused by nitriding reaction. Since cracks were generated in some specimens of 5-layer structure, improved specimens of 7-layer structure were prepared. To examine the effect of a particle size on toughness, WC-Co system alloy specimens with different particle sizes were also prepared. As a result, no cracks were found, and residual stress and fracture toughness were affected by particle size. In addition, the following were studied: technique of mass production, observation of fine structures, analysis of thermal stress, thermal shock resistance, and friction and abrasion characteristics. 13 refs., 65 figs., 15 tabs.

  5. Report for fiscal 1998 on results of research and development of silicon-based polymeric material; 1998 nendo keisokei kobunshi zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research and development of 'silicon-based polymeric materials' has been implemented under ten year plan since 1991 by the research and development system for industrial science and technology, with the following subjects conducted in the general accounting section of fiscal 1998. In the research and development of the synthetic technology of electrically conductive silicon-based polymeric materials, a synthetic method was established for unsaturated side-chain group polysilanes as a basic structural unit for structuring multidimensions. In the research and development of the synthetic technology of new silicon-based polymeric materials capable of plotting circuits, network-shaped polysilanes with various amino groups introduced were synthesized, for which electrical conductivity and temperature dependency were measured. In the research and development of new silicon-based polymeric materials with an electro-luminous function and the like, polymeric synthesis began developing smoothly that has hole-transporting and electron transporting properties concerning the electro-luminous function. In the research and development of silicon-based photoelectric conversion materials, examination was made on the improvement of photoelectric conversion performance by materialization technology including lamination and mixture. The general investigation and research committee contrived further advancement of the research and development. (NEDO)

  6. Achievement report for fiscal 1990 on research and development of high-efficiency molecule separating membrane materials; 1990 nendo kokoritsu kobunshi bunrimaku zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    In order to achieve high efficiency and energy conservation in the separation processes in the chemical industry, activities were performed to seek high-efficiency liquid separation films, gas separation films, and the related technologies that make possible separation, condensation, and refinement of substances that have consumed large amount of energy in the conventional separation processes (for example, water-alcohol, and rare gases), and substances difficult of separation and refinement because of resemblance in physical and chemical properties (for example, isomer mixed substances). For the gas separation films, research and development has been made on (1) high-order molecule recognizing films, (2) high-density metal complex fixing thin films, (3) high-functional complex films, and (4) re-activating oxygen condensation films. In (1), attempt was made on oxygen condensation by impregnating the carrier film with aqueous cobalt complex solution with regard to oxygen, for example. Research has been made on alcohol condensation film in the liquid selecting and separating films. Research and development has been made on fluororesin films for water/polar organics separation, (3) high-order structure control of water selective and permeating films, (4) water/acetic acid separating films, and (5) particle separation process utilizing liquid films. (NEDO)

  7. Progress of admixtures and quality of concrete. 2. ; Approaches to ultra-high-strength concrete. Konwa zairyo no shinpo to concrete no hinshitsu. 2. ; Chokokyodo concrete eno approach

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, T. (Shimizu Construction Co. Ltd., Tokyo (Japan)); Abe, M. (Building Research Institute, Tsukuba (Japan))

    1994-02-15

    Ultra-high-strength concrete of 600 kgf/cm[sup 2] or more is reviewed. MDF (macro defect free) cement, spheroidal cement and mechanically stabilized cement have been developed for ultra-high-strength concrete, however, in general, DSP (densified system containing homogeneously arranged ultra-fine particles) technique is now usual in which a water-cement ratio is reduced by use of advanced air entraining and water reducing agents and cured concrete is densified by use of ultra-fine particles as admixture. Four kinds of substances such as naphthalene system and polycarboxylic acid system are used as air entraining and water reducing agents, and silica fume is used as ultra-fine particle admixture which can be effectively replaced with blast furnace slag or fly ash. Various use examples of ultra-high-strength concrete such as an ocean platform are found in the world, however, only some examples such as a PC truss bridge and the main tower of a PC cable stayed bridge in Japan. 22 refs., 10 figs., 2 tabs.

  8. WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

  9. Survey of the trend of technical development and industrial policies in Asian countries; Asia shokoku ni okeru gijutsu kaihatsu no doko to sangyo gijutsu seisaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A sharp rise in industrial productivity in Asia countries indicates a rising level of R and D technology. Since Japan has not clearly grasped the R and D ability in these countries, it has not given appropriate personnel/material R and D support to them. Therefore, for the purpose of exactly grasping the R and D ability of Asian countries (Korea, Taiwan, the Philippines, Indonesia and India) and studying an effective and appropriate method for R and D cooperation, a survey was conducted of R and D potentials in Asia and R and D support policies of the countries. As a result of the survey, the following are taken up as items to be considered: promotion of exchanges between Tsukuba, etc. in Japan and research/university towns and science parks being constructed in lots of countries, participation of private companies in high-tech joint work in cooperation with Japan, sending information from Japan using internet, etc. and exact grasp of needs at partner side, cooperation given to new comers without asking for research results (use of OB researchers, etc.) 25 refs., 39 figs., 59 tabs.

  10. Report on technological trend survey in fiscal 2000. Survey on bio-technology development strategy; 2000 nendo gijutsu doko nado chosa hokokusho. Bio technology gijutsu kaihatsu senryaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey and research have been performed on bio-technologies as to their seeds of technological development projects to be worked on by the government from the viewpoint of industrial utilization technologies. In the survey on the trends of research and development and technological development on human-genomes, the survey has been done on the status of execution in the Millennium Genome Project, and how the works related to human-genomes are done at the bio-related government based research organizations and the private sector research organizations. Trends related to the human-genome research in overseas countries were also surveyed. With regard to the future prospect of research and development in the post genome age, discussions were given on the result of the questionnaire survey on opinion leaders in the industrial, governmental and academic areas. In discussing the viewpoint of the industrial utilization technologies related to human genomes, candidates assumed usable in the genome related application fields were discussed, and a basic framework of a technological map was prepared. Based on the results thereof, the technological development areas anticipated to be important in the future were extracted, and the technological development themes were discussed. (NEDO)

  11. Survey of the situation of technology succession. Databases of articles including in industrial technology museums; Gijutsu keisho jokyo chosa. Sangyo gijutsu hakubutsukan shuzohin D.B. hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To promote the succession of history of and the creative use of industrial science technologies, the paper made lists and databases of the articles of industrial technology museums and material halls in Japan. Record/preservation and collection/systematization of history of the industrial technology is useful for forming bases necessary for promotion of future research/development and international contribution. Museums and material halls are the fields for making comprehensive and practical activities. The data were made as one of the basic databases as the first step for promoting activities for examining the technical succession situation in a long term range continuously and systematically. In the classification of the data, the energy relation was divided into electric power, nuclear power, oil, coal, gas and energy in general. Others were classified into metal/mine, electricity/electronics/communication, chemistry/food, ship building/heavy machinery, printing/precision instrument, and textile/spinning. Moreover, the traffic relation was classified into railroad, automobiles/two-wheeled vehicles, airline/space, and ships. Items were also set of life relation, civil engineering/architecture, and general. The total number of the museums for the survey reached 208.

  12. FY 2000 research cooperation project on plastic processing technology/quality inspection technology; 2000 nendo kenkyu kyoryoku jigyo. Plastic kako gijutsu hinshitsukensa gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of improving the production technology of plastic products in Saudi Arabia, the joint development was made of the formation technology/quality inspection technology of agricultural use and food packaging use polyolefin film optimum to environmental conditions of the site, in the light of the needs there, and the FY 2000 results were reported. In the field survey/joint study, for the xenon type weather resistant testing machine and the extruder of the inflation film forming machine which were transported from Japan, the following were carried out: confirmation of the situation of accepting them on the site, functional test of computer of the extruder, installation of the machine testing weather resistance, and the trial operation. In the domestic support study, the extrusion test at laboratory was conducted using the polyethylene resin produced on the site to acquire the basic data for formation stability. Further, the film formation test was made using the equipment with the same specifications as those of the equipment introduced to the site to study the performance of screw extrusion and the formation stability of film. Also conducted were the analytical test/quality evaluation of resin materials/film. (NEDO)

  13. Intelligent social infrastructure technology. Infrastructure technology support ultra-reliable society; Chiteki shakai kiban kogaku gijutsu. Choanshin shakai wo sasaeru kiban gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This survey was conducted to construct the core of intelligent social infrastructure technology (ISIT), and to investigate its practical application to industries and society. For realizing the ultra-safe and ultra-reliable society, it is necessary to develop the ISIT which can integrate various social infrastructures, such as architecture, city, energy, and lifeline systems required for living. For the systematization of cities, it is necessary to process and control the intelligent information by holding integrated and transverse information in common, as to logistics, lifeline, communication, monitoring, and control. For the communication engineering, the centralized systems are acceleratingly to be converted into the distributed network systems. For the mechanical engineering, intelligent control and robot technology are required. For the architectural engineering, a concept exceeding the conventional antiseismic structure idea is investigated. It is necessary to develop a new information technology providing an intelligent social infrastructures by merging the information networks and the physical world seamlessly. Necessity of ISIT is large for constructing the intelligent and ultra-reliable society consisting of these integrated and organized networks. 84 refs., 68 figs., 6 tabs.

  14. Fiscal 1993 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1993 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    There was a progress in the development of oil based C/C (carbon/carbon) composite technology. Studied in a comprehensive endeavor were coordination between various technology developing activities, surveys of trends of relevant technologies, and technological tasks to discharge for the development of materials usable under extreme environments. Technologies developed for advanced composite materials involved (1) oil pitch derived random structure carbon fibers, (2) oil pitch derived onion structure carbon fibers, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. Under item (1), random structure carbon fibers were examined for high reproducibility of physical properties, continuous surface coating technology for fibers, and weavability. Under item (2), onion structure carbon fibers were studied for development into C/C composite reinforced fibers. Under item (3), the mechanical structure of double structure carbon fibers was clarified, and C/C composite materials were fabricated using experimental prepregs worked out after studying matrix composition and impregnation techniques. (NEDO)

  15. Report on achievements in fiscal 1988 on research and development of the photoreactive materials under the next generation basic technology research and development project. Comprehensive surveys and researches on photoreactive materials; 1988 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokuksho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    This paper describes the achievements in fiscal 1988 on comprehensive surveys on photoreractive materials. Based on the research and development institution for the next generation basic technology under the initiative of the Agency of Industrial Science and Technology, development is being promoted on photoreactive materials, or photochromic materials and photochemical hole burning (PHB) materials (materials in which molecular structures and assembly state can be changed reversely by actions of light, leading to expectation of application thereof to ultra-high density recording, displays at high resolution, and light switches). In order to achieve smooth and efficient promotion of the development thereof, development of the related technologies inside and outside the country was surveyed and discussed. Comprehensive surveys and researches were also carried out on the common basic technologies by looking to the well-informed people for guidance on the research. This fiscal year has held joint committee meetings to which lecturers were invited to discuss respective problems in the research and development trends. In addition, as the domestic survey, the status of research and development at the Tsukuba University was surveyed on photo-responsive polymeric gels. Furthermore, as the survey on the overseas technological trends, information related to photoreactive materials was collected mainly on photochemical burning materials in the U.S.A., and the research trends were surveyed. (NEDO)

  16. Fiscal 1991 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1991 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Development of oil based C/C (carbon/carbon) composite technology was carried out. In a comprehensive survey, studies were conducted of the trends of associated technologies and tasks to discharge for the development of materials usable under ultrahigh temperature environments. For the development of advanced composite materials, efforts were exerted to develop technologies in the three fields of (1) oil pitch derived random structure carbon fiber/carbon based matrix composite materials, (2) oil pitch derived onion structure carbon fiber/carbon based matrix composite materials, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. In Field (1), physical properties and the like of a specimen fiber were clarified by studying conditions for manufacturing random structure carbon fibers, and the specimen was provided with a surface coating for the study of oxidation resisting performance improvement. In Field (2), onion structure carbon fiber forming conditions and basic technologies for structure manifestation were established, and basics of fiber surface coating technology were studied. In Field (3), double structure carbon fiber forming conditions were studied, specimen fabrication was carried out, and fiber surface coating technology was studied. (NEDO)

  17. Fiscal 1990 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1990 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    Efforts were made to develop technologies of oil based C/C (carbon/carbon) composites. In a comprehensive survey, studies were conducted of the trends of associated technologies and tasks to discharge for the development of materials usable at ultrahigh temperatures. For the development of advanced composite materials, efforts were exerted to develop technologies in the three fields of (1) oil pitch derived random structure carbon fiber/carbon based matrix composite materials, (2) oil pitch derived onion structure carbon fiber/carbon based matrix composite materials, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. In Field (1), random structure fiber manufacturing conditions were studied, basics of their relations with fiber thermal properties and the like were understood, carbon fibers were provided with surface coating, and studies were made to enhance the oxidation resistance of carbon fibers. In Field (2), fiber forming conditions were studied and their relations with fiber physical properties, such as strength, in an oxidizing atmosphere were grasped. In Field (3), manufacturing conditions and their relations with fiber physical properties were learned, and a technology was developed to manufacture composite rods. (NEDO)

  18. FY 1989 report on the results of the next generation industrial basement technology R and D project - R and D of photo-reactive materials. Comprehensive investigational research on photo-reactive materials; 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. Hikari hanno zairyo sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    As to photochromic materials and photochemical hole burning (PHB) materials, for the purpose of smoothly/efficiently promoting the R and D, the common basic technology was comprehensively surveyed as well as survey/study of the related technology development in Japan and abroad. In FY 1889, a joint committee was held, and a meeting was held of lectures given by lecturers from outside on the following: reversible response LB multilayered film and 2D optical switching element, photochemical HB and solid polymer, photovoltaic excitation dynamics of polymer solid, wavelength variable/semiconducting laser, optical memory, etc. A meeting for study/discussion on the details was also held. Items for the meeting were as follows: optical orientation control of nematic liquid crystal by photochromic surface, design of photochromic molecules, molecular movement and photo-reactivity in molecular aggregation system matrices, PHB spectra and mesoscopic structure control, continuous HB using semiconducting laser and sub-picosecond photon echo, quinone system derivative PHB in polymer matrices, etc. (NEDO)

  19. Research and development project in fiscal 1989 for fundamental technologies for next generation industries. Achievement report on research and development on photoreactive materials (Research on enhancement of functional stability of PHB materials); 1989 nendo hikari hanno zairyo no kenkyu kaihatsu seika hokokusho. PHB zairyo no kino anteisei kojo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective of establishing the fundamental technologies related to photo reactive materials that can be used for ultra-high density recording, high-resolution indication, and photoswitches by controlling structures and association status of molecules by using actions of light, research and development has been performed. This paper summarizes the achievements in fiscal 1989. In the research of synthesis and evaluation of PHB materials, a possibility was verified to form holes at temperatures higher than the liquid nitrogen temperature on all the materials in which six kinds of ionic porphin derivatives were dispersed into polyvinyl alcohol. Stability of holes in the tetra-alkyl pyridinium porhpn/polymer system was evaluated, the hole half-width was measured accurately by using ring die laser, and the hole forming characteristics were evaluated by means of high-power density and brief laser light irradiation. In search of new guests, a two-photon absorption spectrum measuring instrument was assembled to measure samples having zinc tetra-phenylporphyrin derivative as the guest. In addition, hole formation was discovered in samples having indomethylene based coloring matter as the guest. (NEDO)

  20. Fiscal 1989 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Research and development of advanced composite materials using oil as raw material); 1989 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Sekiyu genryokei senshin fukugo zairyo no kenkhyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    The research and development of advanced composite materials succeeds the composite material development project initiated in fiscal 1981, and activities were conducted in the two domains of advanced composite material development and comprehensive survey implementation. In the comprehensive survey, trends of associated technologies were investigated, and technical tasks were studied relative to the development of advanced materials. In the effort to develop advanced composite materials, activities were conducted in the three fields of (1) oil pitch derived random structure carbon fiber/carbon based matrix composite materials, (2) oil pitch derived onion structure carbon fiber/carbon based matrix composite materials, and (3) oil pitch derived double structure carbon fiber/carbon based matrix composite materials. In Field (1), relations between conditions of forming carbon fibers out of pitch and carbon fiber random structure were elucidated, and development was started of technologies for providing fibers with oxidation resisting surface coatings. In Field (2), relations between conditions of forming carbon fibers out of pitch and carbon fiber onion structure were elucidated, and development was started of technologies for providing fibers with oxidation resisting surface coatings. In Field (3), efforts were started to elucidate oxidation resistance governing factors. (NEDO)

  1. Report for fiscal 1995 by basic liquefaction technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Delivered at the 1st meeting are a report on the fiscal 1995 research plan and an interim report, involving the use of coal-derived oils, research on refining technology using a PDU (process developing unit), reforming technology and petroleum blending technology for coal-derived oils, development of new reforming catalysts, technology of heterocompound separation, and the development of applications. Reported in relation with the development of environmentally friendly coal liquefaction technology are the study of coal liquefaction conditions, study of the upgrading of basic liquefaction techniques for the improvement and rationalization of the liquefaction process, and a project of liquefaction technology internationalization. A report is also given on a liquefaction catalyst study meeting. At the 2nd meeting, reports are delivered on the development of environmentally friendly coal liquefaction technology, including a briefing on the situation in general, designing of highly active catalysts, elucidation of the mechanism of emergence of activity, achievement of the marginal yield of coal-derived oils, and the properties of catalyst attached to coal. Delivered in relation with the use of coal-derived oils and technology for their refining are a briefing on the situation in general and reports on the blockup to occur in the naphtha fraction process and measures to counter the problem, control of the metamorphosis of active metals in reaction, heterocompound separation technology, and the development of applications. (NEDO)

  2. Effective utilization technology of carbon dioxide. CO sub 2 no yuko riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Ibusuki, T. (National Research Inst. for pollution and Resources, Tsukuba (Japan))

    1991-03-12

    As carbon dioxide-related environmental measures, method was explained to chemically convert and utilize carbon dioxide. Synthesis is possible of methanol, carbon monoxide, different carbohydrates, etc. by catalytic hydrogenation of carbon dioxide, using hydrogen produced by the electrolysis of water. Task consists of heightening in both convertibility and selectivity, and abundant supply of low cost hydrogen. Methane, alcohol, etc. can be synthesized by electrochemical reducion of carbon dioxide. Because of effectively inserting multiple electron, discssion is being made of catalyst, intergrated with electrode, and electron transmitter. The photoelectrochemical reduction of carbon dioxide can be also made by utilizing photoelectric current, generated upon photoradiation on the semiconductive electrode. However, task consists of heightening in both efficiency and selectivity. Photochemical reduction of carbon dioxide, actually made by green plant, consists of oxidationlike decomposition of water and reduction of carbon dioxide. Both those reactions are skillfully separated by intermediation of very quick electron transmission system. Reduction is being studied with semiconductor, metallic colloid, enzyme, metallic complex and other various catalysts. 10 refs., 3 figs., 4 tabs.

  3. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy (Textile technology field)); 1999 nendo choki energy gijutsu senryku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sen'i gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a textile technology field. Social demand and constraint in the 21st century restrict human life and industrial activity, however, include huge business chances. This technology strategy aims at construction of textile business contributing to the society, and improvement of the international competitiveness of Japanese textile industry. Analysis was made on the current international competitiveness of the textile industry in comparison between Japanese and American productivity. As factors hindering technological innovation, the following were pointed out: poor cooperation among industry, academia and government, poor cooperation among different kinds of industries, poor preparation of basic technology, knowledge base and creation base, and poor deregulation. As the future target and strategy, 7 technology targets, 2 creation targets, and every target year were showed. 4 proposals were also showed as follows: preparation of a technology base, creation base, talent education and knowledge base, and protection of intellectual property rights. (NEDO)

  4. Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Doi, Y [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J

    2000-03-24

    Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

  5. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  6. Technical issues and a prospect of ICAI. Chiteki CAI no gijutsu kadai to kongo no doko

    Energy Technology Data Exchange (ETDEWEB)

    Otsuki, S. (Kyushu Institute of Technology, Kitakyushu (Japan))

    1992-12-10

    This paper explains technical issues and a prospect for intelligent computer assisted instruction (ICAI) which combines the intelligent tutoring system (ITS) with an open-ended (discovery) type education system. The paper summarizes the ITS characterized by modelling students based on error-origin diagnostic technologies; various functions that have been realized for the first time therefrom; different methods for error diagnosis and error-origin diagnosis; and criteria to evaluate these methods (evaluating generality, coverage, and tractability). The paper indicates that no complete diagnostic methods have been obtained according to these criteria, that, therefore, an issue of incompleteness in the student model still remains, and that unsolved issues in the ITS include some that exceed the framework of the ITS. Also mentioned in the paper are that the discovery type education system has a possibility of realizing an education with new quality, and that a new attempt is being performed to merge the ITS with the discovery type education system. 17 refs., 2 figs.

  7. FY1995 generic supercritical water technology; 1995 nendo generic technology to shite no chorinkai riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the establishment of the basis of supercritical fluid technology, we perform elucidation of the specific feature of the supercritical fluid as a reaction media and development of some new process. In this study, we first studied the fluid structure of SCF through in-situ spectroscopy and MD simulation. As a result, significant hydrogen bonding amongst water molecules and a solvation structure around the solute were observed in the supercritical state. This fluid structure has new features different from that of high temperature steam or liquid water. We found that this is closely related to the difference of bulk properties of SCF and local one around the solute. On the basis of these fundamental findings and with the better understanding of the specific features of SCF as a reaction media, development of some new process had been conducted more efficiently and successfully. The processes being developed in this study include 1) waste biomass and plastic conversion to recover chemicals, 2) hydrogenation of heavy oil for desulphurization through partial oxidation 1 and 3) hydrothermal synthesis of metal oxide fine particles. (NEDO)

  8. Technical features of steel structure construction by Kawasaki Steel; Kawasaki Seitetsu no kokozo gijutsu no tokucho

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, T.; Urata, I.; Okata, S. [Kawasaki Steel Corp., Tokyo (Japan)

    1996-03-01

    In the steel structure technology of Kawasaki Steel, the joint technique (e.g., welding) is added to them while developing or improving the products that meet the social needs as a material supplier. Moreover, the execution technique that manufactures materials or constructs them as an integrated structure, the structural analysis that conforms to the function and application of a structure, and the design technique on dynamic properties or durability such as earthquake resistance, fatigue, and corrosion resistance are synthetically expanded for engineering. In this paper, a building steel frame, non-residence building, bridge, and harbor structure as steel structure in the building and construction fields were described for each structure genre. The structural technology of a building steel frame is summarized to the products of pillar materials. An earthquake brace, using a dead soft steel, with high earthquake energy absorption capability and a damping wall were also developed. The design and execution technique of a large roof was systematized. The exchange technique of a road bridge RC floor and the technique of an unstiffened suspension bridge for pipeline were developed. A new technique was also developed for a suspension monorail track and offshore structure. 30 refs., 5 figs.

  9. How to proceed R and D effectively; Gijutsu kaihatsu no koritsutekina susumekata

    Energy Technology Data Exchange (ETDEWEB)

    Kawakita, Tetsuya [Ajinomoto Corp., Tokyo (Japan)

    1999-07-05

    They greatly divide R and D into next three in the enterprise, it is considered. (1) The goal-oriented basic research. (2) The applied research. (3) Technology development. Here, they try to want to consider the measure for efficient result sending out in technology development. It always considers that the largest effect is raised in research personnel who was limited in advancing technology development, it is observed in the standpoint for the operation management. The thought of Concurrent Engineering has already been taken in daily management, and it is had thing sure. In large wave of the internationalization, the high competition superiority is ensured in respect of the cost competitiveness, while the goal is clarified, and while it lectures on the means for overcoming the bottleneck. Responding to the expectation of the management by the further improvement in the technology development force believes not differing role of the engineer in the enterprise. (NEDO)

  10. Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

  11. Plant growth regulation by the light of LEDs; LED ko wo tsukatta shokubutsu saibai gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, H. [Mitsubishi Chemical Co., Tokyo (Japan). Yokohama Research Center

    1996-03-01

    Light Emitting Diode (LED) has not only an excellent display function for the luminescent device but also a superior feature without other lamps as light source for plant growth. It was National Aeronautics and Space Administration (NASA) to find out such merit for this light source for plant growth and try at first to use for plant growth at the space. They began to examine the LED application to the light source for the plant growth at the space since a stage at high cost of the LED, to develop some researches centered at cultivation of lettuce, wheat, and others. Finding out future possibility of cost-down of the LEDs on the cost/performance and large merits of the LEDs for control of the plant growth and plant physiology, authors have conducted some cultivation experiments of the plants using the LEDs for light source some years ago. In this papers, characterizations, actual possibility, and future developments of the LEDs for the light sources of the plant growth, are introduced. 5 refs., 4 figs.

  12. Comprehensive research cooperation in environmental technology in fiscal 1995; 1995 nendo kankyo gijutsu sogo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Cooperative study was conducted on research subjects concerning water pollution preventive technologies in China and Thailand. In China, straw pulp mills were studied which were in the Institute of Light Industry Environmental Protection and the Environmental Engineering Course of Jinghua University. The following studies were jointly conducted: survey of the water quality pollution caused by waste water, investigational study on production technology and waste water treatment technology, extraction of technologies effective to preserve water quality, study/evaluation of economical efficiency of the said technologies, etc. In Thailand, cooperative research was conducted on automatic measuring technology for factory waste water in a model industrial estate of the Thai National Industrial Estate Corporation. Items for the study were a study on measuring technology for water quality environment, an investigation on the status of water quality environment in the model industrial estate, a study on automatic measuring technology for plant waste water, a study on how to use measuring data in the model industrial estate, etc. Every study enabled technical data accumulation at every research institute through field research exchanges. 24 refs., 91 figs., 45 tabs.

  13. Rear impact whiplash neck injury reduction technology; Jidosha komen shototsu ni okeru muchiuchisho teigen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Y.; Ichikawa, H.; Kayama, O. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1999-11-01

    Even though whiplash neck injuries suffered in low-speed rear impacts are one of the major concern in traffic accidents, the mechanism of the injuries is not fully understood at present. Hence, the countermeasures have not been clear, yet. The bio-mechanical research was done to understand the injuries and three different modes of occupant's motion related to the mechanism were found. Based on this research, Nissan Active Head Restraint has been developed to reduce whiplash neck injuries in low-speed rear impacts. (author)

  14. Future trend of science and technology. Kagaku gijutsu wa doko made susumu ka

    Energy Technology Data Exchange (ETDEWEB)

    Kondo, S. (Inst. for Future Techynology, Tokyo (Japan))

    1991-01-05

    The fifth survey of a large scale technology forecast which is conducted by the Science and Technology Agency (Japan) is now started. This paper gives a prospect on the megatrend of technical innovation according to the 4th. Survey conducted in 1987. Threefold viewpoints of the analysis are as follows: Type of the technical innovation (Breakthrough type and technology melting pot type). New technology and new product development (adding higher value, human friendly type). Leading technology qualitative innovation of information/electronic technology; pursuit of highly intelligent technology. (Biological technology qualitative innovation of bio-technology: pursuit of simulated organism function). The technical forecast is conducted on 17 field sectors. Examples of design-synthesis and fabrication'' technology are a technology of control based on clarification at atomic and molecular levels'', and another is design and synthesis technology of substances by means of a computer science:.'' 2 tabs.

  15. Disinfection technology with ozone for cryptosporidium; Cryptosporidium taisaku to shite no ozone shodoku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Y.; Takahashi, K. [Fuji Electric Co. Ltd., Tokyo (Japan); Motoyama, N. [Fuji Electric Corporate Research and Development, Ltd., Kanagawa (Japan)

    1998-06-10

    Measures against Cryptosporidium parvum (C. parvum) in the waterworks are discussed. C. parvum is a pathogenic protozoan, and exists in the form of oocyst protected by a hard shell. It does not multiply in water or food, but does in human intestines and causes violent diarrhea and bellyache. A grave concern was created when many people were infected with the protozoan via tap water in Japan and the United States. Under such circumstances, ozone is used in an experiment to inactivate C. parvum. It is found that the C. parvum oocyst inactivation effect is evaluated by using a Ct value (disinfectant concentration Cmg/Ltimescontact time in minute) and that ozone treatment inactivates 90-99% of the protozoan. When various advanced water treatment technologies are being introduced for the purpose of serving safe and tasty water, the outcome of this study conveniently offers an ozone treatment method that will additionally inactivate pathogenic protozoa. Studies will be continued to elucidate the effects of factors of ozone treatment and water quality for the completion of an ideal disinfection process. Reference is made to an example of disinfection work implemented at a water purification plant of Milwaukie City, United States. 9 refs., 6 figs., 4 tabs.

  16. Earth-friendly refuse processing. Chikyu kankyo wo kangaeta gomi shori gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Nishigaki, M. (Takuma Co. Ltd., Osaka (Japan))

    1994-06-15

    This paper contains six articles: (1) Earth-friendly Garbage Disposal, (2) Erasable Copy Machine, (3) Making Plastics from Shell of Crustacean, (4) From Garbage into Petroleum, (5) Utilization of Sewage Sludge for a Recycle-type Society, and (6) FRP Boat Disposal Technology. All articles address the latest topics about disposal of wastes and garbage that have been attracting general attention in environmental issues. The article (1) presents the latest waste incineration technology, garbage power generation, and disposal and utilization of incineration residues. The article (2) is about a prototype of the copy paper regeneration device (toner remover) developed and produced by Ricoh Co., Ltd. The article (3) describes biodegradable plastics using chitin and chitosan that can be acquired from shell of crustacean. The article (4) describes how to extract oil or gas from plastic waste through its thermal decomposition. The article (5) presents volume reduction and utilization of sewage sludge. The article (6) presents disassembling and disposing waste plastic boats that have been rapidly increasing. 8 refs., 27 figs.

  17. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  18. Prospect of concrete technology; Kenchiku ni okeru korekarano konkurito gijutsu no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Tadahiko [Shimizu Corp., Tokyo (Japan)

    1999-10-10

    The privatization of state-owned companies, the abolition of the protectionism to domestic industries and the market liberalization, deregulation to the economic activities or movement to abolition of regulation were concretely made a start. Moreover, the reform of the social life was also requested with an increasing of international global environmental preservation. These reform influences in the construction industry have been affected and could not ignored in consideration of the development in the 21st century. In this paper, the summary of reform in development, construction industry; especially the correspondence in the construction industry and the relation to concrete technology from now were described. Especially, concerning establishment of concrete technology, it was given as the construction of the safe and comfortable space, highly production technical development, countermeasures to resource-saving and environmental preservation, search of new concrete materials, development of the renewal technology and correspondence to large project. (NEDO)

  19. Emerging technologies for demand side management. Demand side management jitsugen no tame no saishin gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Iyoda, I [Mitsubishi Electric Corp., Tokyo (Japan)

    1993-11-05

    This paper explains the latest situation in hardware technologies to realize the demand side management, divided into the following technologies: communications technology, measurement technology, client information system technology, load controlling technology, home automation technology, and energy storing and saving technologies. Speaking of the communications technology, information exchange between the supply side and the demand side is important in the demand side management, whereas a technology intended of automatic power distribution and automatic meter-reading is advancing in development. The technology covers transmissions using from power lines and telephone lines to optical cables and wireless communications. Power line communications using power transmission lines as communication lines are simple and economical, but weak against noise, and not suitable for long-distance communications. Wireless communications have been drawing attentions along with the development of mobile communication device technologies. These technologies will give benefits to electric power companies in the initial stage of their use, such as for load investigation and general automation in power distribution. They would shift to benefiting users in about 2010 covering from security information such as about power interruption to publicity information and educations. 8 refs., 8 figs., 1 tab.

  20. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Aerospace technology field (Aircraft technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kokuki gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of an aircraft technology field. In an aircraft field, since the major theme is application of new technologies to new airframe development, with joining in international cooperative development of aircraft, Japanese initiative development of airframes based on the domestic market demands and profitability should be started as early as possible. Because there is no airframe development by only one country including U.S.A., Japan is profitable to unite with some overseas companies, and invest selectively in specific leading fields. Positive technical support to safety, reliability, comfort and environment harmony are also important. More important theme than establishment of elementary technologies is preparation of an integrated flight demonstration system to expand application chances of development results, and preparation of various test facilities for tests required during development activities. Application of information technologies to the whole aircraft industry, and organic cooperation between the private and public sectors are also important. (NEDO)

  1. Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

    1994-07-25

    With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

  2. Advanced technology trend survey of micromachines in Europe; Oshu ni okeru micromachine sentan gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    In this research survey, the development trend of micromachine technology in Europe was surveyed, development level of micromachine technology of European companies was grasped, and practical application fields of their target were investigated. Technology development level of private companies in Japan`s national projects and practical application fields of Japan`s target were arranged. Trends of micromachine technology development are compared between Japanese companies and European companies. Among micromachine technology development projects in Europe, ``8520 MUST`` is a part of the ESPRIT Project. About 40,000 companies among about 170,000 companies in whole Europe are relating to the MUST Project. The main fields include the manufacturing technology, process control of machines, technology of safety, sensor technology in environmental fields, and automotive technology. The marketing fields of application include the automobile, military technology, home automation, industrial process, medical technology, environmental technology, and games. The results can be compared with the direction of research and development in Japan. 22 figs., 8 tabs.

  3. Present status and prospect of the pneumatics; Kukiatsu gijutsu no ayumi to kongono kenkyu no kadai

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, S. [Waseda University, Tokyo (Japan). School of Science and Engineering

    2000-05-15

    This paper describes course of pneumatic technologies and problems in future researches. Pneumatic systems are inferior to electric and hydraulic systems in terms of efficiency. It is because electric power is converted into fluidized energy by using a compressor, and then converted to mechanical energy by using an actuator. When theses published from 1990 through 1999 are put in order, the research objects are accounted for half by control related technologies, and researches related to elements account for only one third. This paper enumerates assignments to be tackled positively in the future by utilizing compressibility of air in pneumatic systems, and features of high speed drive utilizing the stored energy instantaneously. Application of air pressure to robotics from the demand of the aging society, and pneumatic tools having intelligent functions must be subjected to new contrivances. These will serve for work assistance systems to enable aged people to perform works, and for activating industries including organic agriculture. Tools in this sense may include impact wrench, and others. Furthermore, development of fundamental studies for 'why air pressure?' is demanded strongly, including the viewpoint of LCA in the recycling type society. (NEDO)

  4. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  5. Manufacturing technology for advanced jet engines; Jisedai jetto engine no seizo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Hirakawa, H [Kawasaki Heavy Industries Ltd., Kobe (Japan)

    1997-04-05

    A part of the latest production technologies for aircraft jet engines is introduced. Outline of the turbofan engine, turbo-prop engine, and turbo-shaft engine are given. Every one of them employs a gas turbine engine comprising a compressor, combustor, and a turbine as the output generator. Increase in the turbine inlet temperature is effective for making the gas turbine engine more efficient. The development tread of heat resisting materials for realizing higher temperature is shown. The current status and future aspect of the manufacturing technology is discussed for each main component of the engine. Technological development for decreasing weight is important because the weight of the fan member increases when the fan diameter is increased to increase the bypass ratio. FRP is adopted for the blades and casing to decrease the weight of the compressor, and studies have been made on fiber reinforced materials to reduce the weight of the disks. The outlines of the latest manufacturing technologies for the combustor and turbine are introduced. 2 refs., 9 figs.

  6. Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-09-01

    Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

  7. Investigations on an environmental technology transfer information network; Kankyo gijutsu iten joho network chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With developing countries (APEC countries) as the main objects, investigations were carried out to issue environmental technology transfer information that Japan has accumulated, and advance exchanges of technical information with persons related inside and outside Japan. As a result of the investigations, it was found that the environmental technology information that serves more effectively for the developing countries is the technical information that has been developed by repeating improvements, has provided actual results in work sites, and is actually used, rather than the state-of-art technologies. Based on this result, business entities having factories and operation centers located in Mie Prefecture and the city of Yokkaichi were asked to provide data for the actually used environmental technologies. Out of 51 items provided by 17 companies, nine items were selected to be used as prototype database materials for an information network. The objects of information sources will be expanded to a nationwide scale in the future to improve the contents of the database. Problems of handling information copyrights and technical know-hows were presented in the course of data collection, urging the necessity of due considerations on the matter. Necessity was indicated on maintenance and management of data base as well as its quantitative expansion. 1 ref., 4 figs.

  8. Survey of the development of industrial technology in Japan; Sangyo gijutsu rekishi keisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Conditions for creating Japan`s type technologies have been investigated by extracting technologies and experiences meriting the succession to the next generation among the industrial technologies in Japan after World War II. Technological creativity of Japan began to appear from the 1970`s. Quartz watch of SEIKO, U-Matic VTR of SONY, ladle refinery method of DAIDO Steel, PAN-based carbon fiber of TORAY, continuous annealing of Nippon Steel, calculating machine using liquid crystal of SHARP, ASA-400 high sensitivity film of FUJI FILM, and Japanese word-processor of TOSHIBA are the examples. The basic ability to create those products and technology lays in the diversity of firms in electronic device and fine machinery industries consisting the boundary between general and electrical machinery, the systematizing ability and inter-industrial cooperation which were promoted through quality control, automatization of assembly and production control by computer, and the research and development capability which has been brought up during the high economic growth as a learning process of technology. The society and industries have to make efforts to create the new creative conditions for younger generations. Otherwise, Japan`s technology will not develop. 134 refs., 19 figs., 8 tabs.

  9. Laser materials processing as manufacturing technology; Seisan gijutsu to shite no laser kako

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, I. [Osaka University, Osaka (Japan)

    1998-11-01

    This paper describes the laser material processing. Laser is artificial light that uses the amplification based on the induced emission of light. It is very excellent in directivity and monochromaticity. The high power density and concentration characteristics of laser enable a variety of high-performance processing such as junction, removal, reforming, and addition. Excellent controllability (that facilitates the automated processing), transmission performance (the processing by energy transmission in long range space is most suitable for laser), and non-contact processing (that contains no wearing, noise, and contamination) are great advantages that the existing processing method does not have. In the wide wavelength area between ultraviolet and infrared areas, the laser that can be used for material processing is very wide over the range of the continuous oscillation to the ultra short pulse of a nanosecond order. The thermal processing accompanied by melting and evaporation as well as the non-thermal processing (quantum processing) by a photochemical reaction is also available as the type of processing. The processing used for manufacturing technology is almost thermal processing including removal, junction, reforming, and addition. The thermal processing covers the range of electronics to heavy industry. 29 refs., 12 figs., 2 tabs.

  10. Information communications technologies that surpass the global communications network. Sekai tsushinmo o koeru joho tsushin gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    1990-05-01

    Development of information communications technologies that surpass the global communications network is being pushed forward in order to establish the global village that McLuhan foretold in 1964. Effects of hybrid intensification with the intensification of communications technologies and computer technologies have become evident as facsimiles, automated teller machines of banks, home videos, automatic response telephones with synthetic voices, compact disks, portable telephones, video games and high-definition televisions were developed and put to use in a wide range. Intensification and integration of computer technologies and communications technologies has every possibility, but it also has a peculiar aspect of lacking guiding principles. Uncertain factors of the values of informations in the market are ever increasing, and their true values are yet to be found. Anyhow, it is a long way to the goal of the global village.

  11. Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

    1997-03-01

    The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

  12. Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

    1996-09-01

    This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

  13. Study of the O2/CO2 combustion technology; Sanso nensho gijutsu ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kato, M [Center for Coal Utilization, Japan, Tokyo (Japan); Kiga, T; Yamada, T [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Arai, K [Nippon Sanso K.K., Tokyo (Japan); Mori, T [Inst. of Research and Innovation, Tokyo (Japan); Kimura, N; Okawa, M [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    This study is being progressed during a period from 1992 to 1999 as part of the NEDO`s clean coal technology program. This paper describes what has been discussed to date. The absorption method and the adsorption method may be used to recover CO2 as means to deal with the problem of global warming resulted from burning coals. These methods, however, have problems in economy caused from concentration of CO2 in flue gas being low. The present study is intended to raise the CO2 concentration in flue gas by using oxygen plus circulated flue gas in the place of combustion air, so that CO2 may be recovered as it is without being separated from the flue gas. Therefore, an oxygen-blown pulverized coal fired power generation plant having a cryogenic oxygen manufacturing equipment was designed to discuss the plant operability and economy, and the pulverized coal combustion technology by using a dynamic simulation. A large number of findings have been obtained already, and the study has reached a level at which grasping the whole image is now possible. 13 figs.

  14. 6th Conference on Coal Utilization Technology; Dai 6 kai sekitan riyo gijutsu kaigi koenshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    The paper compiled the papers presented in the 6th Conference on Coal Utilization Technology held in September 1996. With relation to the fluidized bed boiler, reported were Field operation test of Wakamatsu PFBC combined cycle power plant and Development of pressurized internally circulating fluidized bed combustion technology. Regarding the coal reformation, Development of advanced coal cleaning process, Coal preparation and coal cleaning in the dry process, etc. Concerning the combustion technology, Study of the O2/CO2 combustion technology, Development of pressurized coal partial combustor, etc. About the CWM, Development of low rank coals upgrading and their CWM producing technology, Technique of CWM distribution system, etc. Relating to the coal ash, Engineering characteristics of the improved soil by deep mixing method using coal ash, Employment of fluidized bed ash as a basecourse material, On-site verification trials using fly ash for reclamation behind bulkheads, Water permeabilities of pulverized fuel ash, Separation of unburned carbon from coal fly ash through froth flotation, Practical use technology of coal ash (POZ-O-TEC), etc

  15. Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

  16. Fiscal 1995 report. Liquefaction key technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The subcommittee held the 1st meeting in September 1955 and the 2nd in March 1996, when fiscal 1995 research plans and research results were introduced and deliberated. In the study for designing a high-dispersion catalyst and the elucidation of the mechanism of activity expression, catalysts of highly dispersed iron supported on the brown coal surface in various ways were compared with each other in terms of liquefaction activity. Furthermore, geometric changes in the iron catalyst during the sulfurizing process were examined using the XRD (X-ray diffraction) and TEM (transient electromagnetic) methods. An improved catalyst was found to achieve a liquefaction yield near the Yallourn coal liquefaction limit in a high boiling solvent system. Concerning the study of coal oil product applications and refining technologies, reports were delivered on research results relating to the problem of blocking to occur during naphtha fraction refining and measures therefor, inhibition of active metal geometric changes during reaction, methods for separating hetero-compounds from coal oil and application thereof, and so forth. (NEDO)

  17. AI technology and automobile. ; Toward vehicle autonomy. AI gijutsu to jidosha. ; Sharyo no jiritsuka ni mukatte

    Energy Technology Data Exchange (ETDEWEB)

    Okuno, A. (Mazda Motor Corp., Hiroshima (Japan))

    1991-01-01

    This report describes the vehicle autonomy by using artificial intelligence (AI) technology. Owing to a remarkable progress of AI technology, it is forecasted that driving support system will be introduced into the market till 2000, and higher autonomous navigation system will be introduced since about 2010. Autonomous vehicles have capacities of recognizing the outside world and of navigating roads by themselves, and with their enfanced environment adaptability the road transportation in the future is expected to be much more safer than in the present. The autonomous vehicle can warn its driver of potential dangers and correct operational errors of the driver. In order to realize such autonomous vehicles, extensive researches on perception systems, decision making systems and driving support systems are needed. 9 refs., 10 figs., 1 tab.

  18. Domestic and overseas situations of Japanese automobile industries; Jidosha gijutsu. Jidosha wo torimaku shojosei

    Energy Technology Data Exchange (ETDEWEB)

    Kawahara, H. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1998-08-01

    The economic circumstances in 1997 are characterized by a high rule in the United States, slow developmental trend in Europe and lagging situations in Asia. The political and economic situations of main counties in the world are summarized with indication of Japanese dull activities, financial crisis and their countermeasures as well as the trade friction in 1998. The number of cars sold in Japan decreased to 3.71 millions in 1997 from 4.55 millions of 1996, while cars imported amounted to 360,000 in 1997 (-14.7% compared to that of the preceding year), the number of exported cars were 4.55 millions as compared to 3.71 millions in the preceding year, namely about 23% increase, of which 1.41 millions for North America and 1.25 millions for Europe. Other evolutional facts are also presented zone by zone. Then, questions which the Japanese automobile industries are faced to are enumerated and explained. The overseas production bases and their activity trends are mentioned, focusing on the modular production system as well as the lean production system as for the international expansion of the products, whereas market strategies with direct injection engine, low emission, hybrid car and so on are described in terms of technical development. Lastly, and innovation of physical distribution tat takes place in the United States such as a movement to a larger scale dealer system, car dealing business through internet and so forth are mentioned including the Japanese trials in line with these matters forecasting an ever-intensive concurrent. 5 refs., 5 tabs.

  19. International Symposium for the Promotion of APEC Environmental Technology Exchange; APEC kankyo gijutsu koryu sokushin symposium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-11

    The International Symposium for the Promotion of APEC Environmental Technology Exchange was held under the theme `The function and role expected of the APEC Virtual Center,` with the objectives of clarifying the need for future intra-regional environmental technological exchange, defining the types of information and personnel exchange, and promoting the use of interactive character of the APEC Virtual Center for Environmental Technology Exchange by encouraging access to and participation in the Virtual Center project. It was held in the period of 11th and 12th, November in 1996, at the venue of Rinku International Convention Center in Osaka. The symposium was attended by 477 persons from nine countries, i.e., Australia, Canada, China, Indonesia, Korea, Philippines, Thailand, the US, and Japan, comprising staff members of intra-regional environment-related organizations. After the keynote speech, `Current status and tasks of environmental technology exchange`, and `Expected roles of the Virtual Center for Environmental Technology Exchange` were discussed. During the plenary session, the chairman summarized the symposium. This summary was carried on the Virtual Center homepage of the Internet

  20. Fiscal 1994 report. Liquefaction key technology subcommittee; 1994 nendo ekika kiban gijutsu bukai hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The subcommittee held the 1st meeting in August 1994 and the 2nd in March 1995, when preceding fiscal year's research results, fiscal 1994 research plans, fiscal 1994 research results, etc., were introduced, and deliberated. In the study of hydrorefining of naphtha, kerosene, and light oil fractions, a nitrogen concentration level of not more than 5 ppm was achieved by refining oils from Indonesian coal. Studies were also made about the two-step hydrorefining system, the relationship between the coal oil refining level and sludge formation, etc. In the research for the development of novel catalysts for upgrading coal oil, the active life of a nickel-supporting catalyst for hydrogenation at the 1st step was somewhat prolonged with an increase in the amount of nickel. In the study of coal liquefaction conditions, an AWIP method was deliberated, wherein liquefaction process waste water was utilized as one of catalytic component adjusting materials. For upgrading liquefaction key technologies, studies were made for catalyst improvement and pretreatment method development, and about the behavior of liquefaction reaction in a high boiling solvent-aided process. (NEDO)

  1. Expectation of rapid prototyping; Rapiddo/puroto taipingu gijutsu no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Kishinami, T. [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering

    1997-04-05

    Prototyping can be defined as the physical and imaginable product model formation process used for verification of production guideline of functional component. Rapid prototyping means the combination of technology forming directly the physical model from CAD data. It is a summarization of technology composed of design assistant technology, model production technology, and integration technology. In 1980`s, 3D System Corp. proposed the stereo lithography. Since then its research and development were promptly carried out as for the technology of rapid formation o physical model. Resultantly, it became possible to fabricate the model designed by the three dimensional CAD within a day using a rapid prototyping system. This can be roughly divided into the following three: (1) stereo lithography, (2) method of melting and hardening by laser irradiation of the powder plastic and wax, (3) 3D-printing method consisting of selectively coating of ceramic powder with binder. 4 refs., 3 figs.

  2. Alternative disinfection technology for water purification systems; Josui shori ni okeru enso daitai shodoku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Aizawa, T. [The Institute of Public Health, Tokyo (Japan)

    1998-09-10

    This paper describes chlorination substituting disinfection technologies used in water purification systems. Chloramine treatment is regarded as effective in reducing trihalomethane (THM). Chlorine is injected in the initial stage in the form of free chlorine to disinfect pathogenic microorganisms in a short time, which is then added with ammonia to convert it into chloramine for further utilization. Chlorine dioxide has not been used in Japan, but introduced in Europe and America to treat THM. Ozone has the strongest oxidizing power, and is used for disinfection, virus inactivation, decomposition of THM precursors, and removal of fungus odor. The ozone treatment will produce aldehyde if an organic matter is present, but aldehyde can be removed by treatment using organismic activated carbon. Ultraviolet ray treatment has an advantage of being difficult of producing byproducts. This system was experimentally compared with free chlorine treatment on disinfection effect, mutagenicity, suppression of producing THM byproducts, and odor removal. In order to assure reliability of microorganismic and chemical safety in tap water supply systems, assurance by considering the entire system is important, not only by operating the disinfection units, but also combining such physical water purifying technologies as coagulation, sedimentation, filtration, and membrane treatment. The use of chlorine substituting disinfectants is also a part of the conception. 6 refs., 8 figs., 5 tabs.

  3. CMOS analog integrated circuit design technology; CMOS anarogu IC sekkei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Fujisawa, A. [Fuji Electric Co. Ltd., Tokyo (Japan)

    2000-08-10

    In the field of the LSI (large scale integrated circuit) in rapid progress toward high integration and advanced functions, CAD (computer-aided design) technology has become indispensable to LSI development within a short period. Fuji Electric has developed design technologies and automatic design system to develop high-quality analog ICs (integrated circuits), including power supply ICs. within a short period. This paper describes CMOS (complementary metal-oxide semiconductor) analog macro cell, circuit simulation, automatic routing, and backannotation technologies. (author)

  4. Noise and vibration improvement technologies for engines; Engine ni okeru soon shindo kaizen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Kuzuoka, H.; Maeda, R. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1999-02-01

    This is an outline of recent measurement and simulation technology for reduction of engine noise and vibration. We can recognize correct phenomenon by visualization of noise and vibration phenomena using new measurement technology. And we can create optimum countermeasures using new simulation technology In this report, examples of application of these technology in the development of NEO-DI engines are provided. (author)

  5. Process improvement technology for petrochemical plant; Sekiyu kagaku puranto ni okesu purosesu kaizen gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Shin

    1999-05-05

    Before, GTC technology Co. was a manufacturer of the tray as a Greenwich technology. It is the subsidiary, which undertakes technology and licence of the engineering firm in U.S.A. at present. It carries out besides the technology licence support in the startup for the prolonged driving of technical service, operating condition of the plant of improvement and optimization and, etc. Has made separation and purification technology, which made extractive distillation to be a beginning good and has the process improvement technology to the PTA (high-pure terephthalic acid) from BTX (benzene toluene xylene) of petrochemical plant. (NEDO)

  6. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Iron and steel technology field; 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) (tekko gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a steel technology field. Japanese steel industry should correspond to requirements of the international economic society as the top runner. Although it is now difficult to suppose a basic technology innovation, stable supply of basic materials is necessary for peripheral industries. The basic raw material technology is the basis of domestic and overseas socio- economic activities. The technology development support system to retain the world-wide leadership of Japanese industries is a strategic issue. Preparation of cooperative R and D bases of industry, academia and government along a national policy is important. Strong promotion of such national projects is also essential as global environment problem, positive use of advanced information tools, development of technologies and products of unexplored fields, and development of new products and demand creation according to social needs. Such measures along social requirements are also important as raw material development to double an energy efficiency, and the policy and system to construct a recycling society and living spaces. (NEDO)

  7. Visualization techniques in diesel engine research. Diesel Engine kenkyu ni okeru kashika gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Komori, M.; Tsujimura, K. (New ACE., Tsukuba (Japan))

    1993-04-01

    In order to grasp the phenomena actually occurring in the combustion chamber for improving the combustion and for reducing the exhaust gas emission of the diesel engines, the visualization techniques are becoming to be essential and indispensable. The authors have observed the spray and combustion, when proceeding the combustion improvement by the high pressure injection, and then have performed the image processing and simulation calculation based on them. The high pressure injection devices used for the experiment are the intensifier type and accumulator type which can generate the injection pressure more than 200MPa, and both of them are the electronic controlled hydraulic drive type, and are driven separately from the engine. Since it was found that the analysis of high pressure injection by the hologram is limited in the conditions, as for the spray, the spray analysis was performed by the transmitted light attenuation method and laser sheet method. As for the combustion, the engine for observing the combustion was trially made, and then the combustion state was observed by the high speed photograph. Furthermore, the flame temperature analysis by the image processing using the combustion photograph and the analysis of flow and turbulence of the flame were carried out. 9 refs., 16 figs.

  8. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

  9. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  10. Investigation into the situation of technology succession; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper made a fundamental investigation to promote historical succession and creative use of the industrial scientific technology. As for the wind power generation, the large-scaling became centralized wind power plants, and the downsizing became the distribution to remote areas. The solar power generation shifted from the thermal power generation to the light power generation. There is also a method to use solar heat directly. As to power systems and the distribution of electric power, the subjects are a combination of energy source, geographical energy transportation, and heightening of consumption efficiency. It was indicated that the subjects changed with a lapse of time under technical/social/systematical conditions, and under the developable energy amount prescribed by those conditions. Heightening of efficiency, which can be realized even by a paper simulation, was realized partly helped by the developing measuring technology. The environmental problem becomes historically severe as a condition of the technical development. However, aimed at was the process where discharged matters and by-products are effectively used and disused matters are not produced. In the coal-thermal power generation, for example, a load of flue gas purification was reduced by the conversion to LNG. 253 refs., 65 figs., 12 tabs.

  11. Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

  12. Trend of laser cutting technology; Laser setsudan gijutsu no saikin no doko

    Energy Technology Data Exchange (ETDEWEB)

    Murai, T. [Mitsubishi Electric Corp., Tokyo (Japan)

    1997-10-05

    Recent trend of CO2 laser cutting is described. The cutting speed has increased five times in these seven years, and cutting is now performed at 8m/min for a hole that satisfies a circularity of 50{mu}m. In the low-speed domain, again, cutting accuracy is as high as 20{mu}m. In the cutting of thick plates, laser encounters some difficulties, which include the increased thermal load on optical parts and devices in the oscillator, lessened cutting condition tolerance, variation in the accuracy of products, difficult cutting, etc. Discussed in this report are measures for correcting factors affecting product quality with reference taken to a thick soft steel plate. A laser beam emitted by an oscillator is condensed by and projected through a condenser lens, and the condensing capability is affected by various factors, such as the beam mode order, beam diameter, and focal length, etc. What is important is to find out the optimal conditions. The assist gas has to satisfy certain conditions because it assumes an important role in controlling the discharge of molten metal from cut grooves, heat generated by oxidation reaction, and cooling. The properties of the material to be cut also exert some influence. In the case of thick plate cutting, the cutting capability is governed by the geometry to be fabricated. Also employed for the prevention of poor jobs due to improper condition switchover and cutting routes is an optimal cutting condition control technique. 3 refs., 12 figs.

  13. High power YAG laser cutting; Koshutsuryoku YAG laser ni yoru setsudan gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Owaki, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1998-08-01

    This paper describes features of high power YAG cutting. The optical fiber transmission YAG laser machining system has some advantages in which optical path length compensation unit is not required and measures for low power loss and dust are not required, when compared with the CO2 laser system. Its application to the cutting of stainless steel plates has attracted attention. Cutting tests of SUS304 were conducted using high power YAG laser. Cutting of SUS304 plate with a thickness of 40 mm could be successfully done at the power of 3.5 kW. Cutting tests of SUS304 pipes with a thickness of 8 mm in water under the depth of 20 m were also conducted using air as assist gas at the power of 2.5 kW. Excellent results were obtained without scale deposition. For the tests by the composite beam using 3 kW and 4 kW systems, SUS304 plate with a thickness of 50 mm could be cut at the cutting speed of 0.1 m/min. Laser cutting of pipes from the internal surface was conducted using a newly developed small machining head which can rotate in the peripheral direction. Excellent quality for welding was confirmed. Cutting speed and plate thickness were improved by combining water jet cutter and YAG laser unit. 6 refs., 10 figs.

  14. Leading research on next generation metal production technology; Jisedai kinzoku shigen seisan gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The energy saving environment-friendly technology for low- grade difficult-to-process ores was researched focusing attention on the hydro-metallurgical process of non-ferrous metals. This research aims at development of both effective leaching system of metals, and separation/crystallization system recognizing the property difference between metal ions in solution. The leaching system allows the inexpensive molecular level control of electron transfer, mass transfer of metal ions and stabilization of leached metal ions in a solid/liquid interface. The system thus allows selective leaching of metals from various resources such as difficult- to-leach sulfide minerals to prepare concentrated solutions. The separation system can obtain high-purity solutions including each metal ion by advanced separation/concentration technology from the solutions. The crystallization technology (including electrolysis) is developed for preparing target metal materials by molecular level control of nucleation, particle growth, thin film formation and bulky metal formation processes. Overall energy consumption is reduced to 1/3 of that of the pyro-metallurgical method, aiming at zero emission. 15 refs., 14 figs., 11 tabs.

  15. Techniques for cost-effective electric information sharing; Cost balance wo koryoshita denshi joho kyoyuka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Shinohara, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    The key technology that can effectively support the sharing of each information such as documents, data, and know-how was rearranged to clarify how to utilize it for constructing an electronic information sharing system. The key technology that supports the sharing of electronic information was rearranged from the viewpoint of information gathering, information rearrangement, and information utilization. The reduction in cost for information gathering and rearrangement is indispensable to the promotion of much information sharing. However, each automation method presently causes the deterioration in quality of the rearranged information and the increase in cost for information utilization. To realize a practical electronic information sharing system, it is important to combine the key technologies properly so that the total cost balance of information gathering and information utilization is improved. Therefore, the combination of character recognition by OCR and unpreciseness retrieval, and the complementary combination of automatic document sorting, based on multiple incomplete rearrangement systems, and multiple sorting menus were proposed. 23 refs., 5 figs., 2 tabs.

  16. Bio-desulfurization technology in Japan; Wagakuni ni okeru baio datsuryu gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Maruhashi, K. [Petroleum Energy Center, Tokyo (Japan)

    2000-05-01

    A bio-reaction of microbes (catalytic reaction by an enzyme) is characterized in that the reaction is carried out at a normal temperature and under a normal pressure and has particularly high specificity with respect to substrate (reactant). It is considered that a low loading process of environment harmony type can be constructed by applying the bio-reaction in petroleum refinery process. CO{sub 2} exhaust and energy consumption in the bio-desulfurization (BDS) is estimated to be 70 to 80% lower than those in hydrodesulfurization (HDS). The bio-technologies that can be applied to the petroleum refinery process include, for example, desulfurization, demetallation, dewaxing, denitration, cracking and so on. In this paper, the present state of bio-desulphurization technology is introduced. Particularly, as the research results in Japan, acquirement of mesophile R.erythropolis KA2-5-1 strain, thermophile Paenibacillus sp. A11-2 strain whose optimum temperature is 50 degrees C, BT degradation fungus Rhodococcus sp. T09 and the like are introduced. (NEDO)

  17. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Machine industry technology field (Semiconductor equipment); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) kikai sangyo gijutsu bun'ya (handotai seizo sochi bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a semiconductor equipment field, viewing until 5-10 years after. For the future semiconductor industry, the favorable cycling of creation of new demands through performance improvement, and further technology innovation through market expansion is essential absolutely. Since technology development is followed by investment, not only the performance of each equipment but also the higher productivity and cost balance of the whole factory are essential. Self-intelligent function and networking are thus necessary for the equipment. As measures for environment preservation and energy saving, such innovative technologies are required as recycling, reuse, reaction process improvement and alternative technology. Because of diverse final products and a short life time of products, a large-scale collective investment is becoming difficult. A mini-line sequential investment production system according to demand scales is under investigation. Some issues such as micro-technology, realization of 300mm wafer, modularization, CIM, reliability and standardization are also described. (NEDO)

  18. Simulation technique on combustion of solid propellant; Kotai suishin`yaku nensho no simyureshon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Iida, Akihide.; Bazaki, Hakobu.; Douke, Kiyotaka. [Asahi Chemical Industry Corp., Tokyo (Japan). Oita Plant

    1999-04-30

    The burning area of propellant grain is one of the most important parameter in conducting of design on solid rocket performance. However, it has been difficult to calculate the burning area of propellant grain with precise and speed by geometrical way since most of propellant configuration have been adopted as complicated. In the present study, the simulation system was developed and produced, which was adapted `particle chasing method` to and made ot compute the burning area transition. Moreover, the reliability on computation by the system was check up on. It was found that the discrepancy of calculation between by the geometrical way and by the system was less than 1%. (author)

  19. Application of FEM flow analysis to environmental engineering. FEM ryutai kaiseki no kankyo gijutsu eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, M; Ando, K; Shimada, S; Umetani, H [Toyota Motor Corp., Aichi (Japan)

    1990-04-25

    In order to apply FEM (finite element method) flow analysis to environmental engineering, the two-dimensional analysis system was developed, and applied to the design of plant ventilation and improvement of an enviromental control equipment. Furthermore, the three-dimensional analysis system was developed to extend its application. Since in a large scale model, no enhancement of a processing capacity was expected even by a supercomputer because of longer I/O times between internal and external memories caused by a small internal memory space, the parallel processing system with multiple external memories was introduced to analyze such models. To achieve more efficient processing, multiple series of renumbering codes were also prepared to optimize the processing order of solvers, elements and nodes. As examples, the improvement of a thermal oxidizer and the ventilation design for a forging plant, and as an example of a three-dimensional large scale model, the flow analysis around a plant were presented. 8 refs., 17 figs., 1 tab.

  20. Generic supercritical water technology; Generic technology to shite no chorinkaisui riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Arai, K; Ajiri, M; Inomata, H; Smith, R; Hakuta, Y [Tohoku University, Sendai (Japan). Faculty of Engineering; Yokoyama, C [Tohoku University, Sendai (Japan). The Institute forChemical Reaction Science; Chin, L [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    This paper describes the measurement and analysis for clarifying solution structure of supercritical water and exhibition mechanism of solvent functions. It also describes the development of new processes using supercritical water as reaction solvent. The PVT measurements were conducted in the supercritical region using pure water and NaCl aqueous solution, to confirm the reduction of molar volume of the electrolyte solution. The hydration structure was examined in the supercritical aqueous solution by the molecular dynamic simulation. As a result, presence of hydrogen bond structure, where the contribution of two branching hydrogen bond can not be ignored, was suggested under the supercritical condition. Characteristics of supercritical aqueous solutions are analyzed through in-situ Raman and scattered X-ray spectral measurements. Moreover, this paper introduces developments of some processes in the supercritical water, such as decomposition of wasted polymers, recovery of chemical materials, reforming of heavy hydrocarbons by contact hydrogenation, and synthesis of fine powders of metal oxide by reaction crystallization.

  1. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

  2. Denchuken review. Prospecting and visualization technology; Denchuken review. Chika no tansa kashika gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-30

    This paper introduces the prospecting and visualization technology cultivated in Denchuken (Central Research Institute of Electric Power Industry). The fluctuations in underground gas, underground water, gravity, terrestrial magnetism, and terrestrial current are information from the earth. The change in underground structure, underground water movement, and underground properties can be grasped using this information. With the progress of electronic engineering, a geophysical exploration method has been rapidly developed in recent years. This method is the most advanced technology in many ground examination methods. In the Denchuken, the following methods have been put to practical use between the shallow section of several meters under ground and the deep section of several kilometers. An underground radar method, seismic prospecting method, electrical prospecting method, CSAMT method that estimates the position of geothermal sources or faults by electromagnetic waves, TDEM method, and AE method that destroys the rock at the depth of the ground and detects by slight sound. Moreover, a geotomography method that can visualize the ground depth in precision using a bore hole by nondestruction executes the tomography based on specific resistance, elastic waves, electromagnetic waves, and percolation. 127 refs., 94 figs., 4 tabs.

  3. Contamination-remedying technology based on biotechnology. ; Bioremediation. Biotechnology wo mochiita osen shufuku gijutsu. ; Bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, M [The Japan Research Institute, Ltd., Osaka (Japan)

    1993-08-01

    Bioremediation technology is outlined. The bioremediation technology is a contamination-remedying technology for the injurious chemical matter discharged in the environment to be made innocuous by utilizing the decomposing ability of microorganisms. That technology is characterized by its energywise economical performance, secondary waste which is not producible and remedy which is possible on site against the contamination. As a treatment system, that technology comprises solid phase bioremediation (The contaminated soil is purified in a soil treatment unit.), slurry phase bioremediation (The contaminated soil is made slurry and decomposed by microorganisms.) and in-situ bioremediation (The treatment is made by injecting nutrients and microorganisms underground.). As for how to use the microorganisms, there are two methods: One in which living groups of microorganisms are activated and the other in which microorganisms are artificially cultivated. As contaminants in the US, listed are organic solvent, wood preservative, high-molecular aromatic halide, agricultural chemical, military waste, heavy metal waste and radioactive waste. 11 refs., 5 figs., 1 tab.

  4. NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

  5. History of technological activities of Japanese industry; Sangyo gijutsu rekishi keisho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    History of technological activities of Japanese industry has been recorded, preserved, compiled and systematized. The purpose is to make international contribution by transmitting Japanese experience and knowledge to the world, and to bring up the human resource for researches by teaching the history of passion and efforts of the predecessors and by arousing interests and creative volitions of science and technology of young persons. However, memorial matters, data and witnesses relating to the history of industrial science and technology are rapidly being lost day by day. When leaving as it is, succession of the history to next generation becomes hard. Under such a situation, basic survey has been conducted to succeed the history of industrial science and technology and promote the creative utilization of them. This is in the third stage of the survey. This report contains the development of new cold rolled steel sheet for cars, plant engineering technology in Mitsubishi Heavy Industries, electronics, electric power distribution technology in Kansai Electric Power Co., Inc., development of the PAN carbon fibers, four cycle and low speed marine diesel engines, production of electrolytic copper foil, development of jet engines, camera makers, and production of office machinery. 86 refs., 12 figs., 9 tabs.

  6. Instrumentation technology to be used for sense alternative. Kankaku daiko wo mezasu keisoku gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Tamiya, E. (Japan Advanced Institute of Science Technology, Hokuriku, Ishikawa (Japan))

    1994-07-05

    Recently, artificial taste sensors or smell sensors that simulate the biological recognition mechanism were developed. This paper describes a smell sensor using natural and artificial fats as the molecule recognizing material and the crystal oscillator or SAW (Surface Acoustic Wave) device as the transducer. The paper also describes the results of the experiments made on the sensor. This sensor consists of 20 LB (Languivir-Blodgett) layers of several types of natural fats on the SAW device. Natural fats on the surface of the crystal oscillator were coated and the response to smelling substances was checked. The result indicates that the response is almost proportional to concentration, and that alcoholic smells can be recognized. To check receiving signal from the sensor system related to absorption and the absorption speed and converting it into higher order information, experiments were conducted to convert data into characters through the neutral network. Though there are still issues of practical use, it was verified that these techniques are effective. 9 refs., 6 figs., 1 tab.

  7. CIM overview. (2). ; Architecture, infrastructure, information technology. CIM soron. (2). ; Architecture, infra, joho riyo shien gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Seryo, K [IBM Japan Ltd., Tokyo (Japan)

    1991-12-10

    The materialization of computer integrated manufacturing (CIM) requires an establishment of its systematizing system, i.e., architecturer and planning of the infrastructure to support it and basic engineering to support the informational utilization. The CIM architecture is classified into management and system structure, strategic planning method, System development introduction method, etc. The infrastructure aims at epoch-makingly heightening the productivity and speed by integrating the production planning, engineering design, accounting, sales, general business and affairs, production engineering, production activities, and activities of suppliers and clients. The informational utilization support engineering comprises the management support tool, decision making support tool, application development tool, etc. What is important is to establish a system of systematizing engineering in order not to be behind the strategic activation era of information to come. 17 refs., 4 figs., 1 tab.

  8. New technique of railway bridges in Hokuriku Shinkansen; Hokuriku Shinkansen tetsudokyo no gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyabayashi, H. [Japan Railway Construction Public Corp., Tokyo (Japan)

    1996-09-01

    This paper presents new technologies of the railway bridges in Hokuriku Shinkansen. Hokuriku Shinkansen of 117km between Takasaki and Nagano is a part of Shinkansen connecting Tokyo with Nagano by nearly 1.5 hours. Its construction is in promotion under severe financial condition, and cost reduction is an essential target. Among the concrete bridges in this section, Kirizumigawa bridge, a prestressed concrete strutted 3-span continuous beam bridge, adopted a lowering erection method for its slant pier. In this method featured by high safety and profitability, the rib component of a concrete arch bridge is vertically erected on a arch support, and installed by swinging it toward the central span. In addition, a cantilever method was adopted to keep the scenery of a national park. Daini Chikumagawa bridge with the longest span of 133.9m among concrete railway bridges is the first cable-stayed prestressed concrete bridge in Shinkansen. Yashiro Minami and Kita bridges of 105m and 90m in central span are the extradosed bridges which were adopted as optimum structure for lowering the beam height of meddle-sized railway bridges. 3 refs., 12 figs., 2 tabs.

  9. Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-10-15

    Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

  10. Bridge and steel structures. History and vision on bridge erection; Kyoryo kokozobutsu. Kasetsu gijutsu no shorai

    Energy Technology Data Exchange (ETDEWEB)

    Mukai, S.; Hayashi, T. [Sumitomo Heavy Industries, Ltd., Tokyo (Japan)

    1998-08-20

    This paper describes the progress of bridge erection technology. It introduces the results of cable erection, rotated/extruded erection, and cantilever erection. The cable erection is a multi point suspension erection using cables. For the rotated/extruded erection, the monolithic construction is conducted on a working yard set in a right angle to the construction position, and the horizontal beams of the bridge piers (corbel girders) are constructed by the rotated method using a slewing base incorporated around the bridge piers at one side. For the construction of stiffening girders of Innoshima-ohashi Bridge of Honshu-Shikoku Joint Bridge in 1978, trussed face bar blocks were extruded from the main tower in order using a travel crane. For the suspension bridges and cable stayed bridges, main towers were erected using various types of cranes. The erection of Tamashima-ohashi Bridge with a weight of 500 ton using an offshore floating crane is introduced as a large block method. Analysis methods and measurement techniques at the site are used in order to analyze the shape in each step under the erection and to ensure the accurate final complete shape. Reduction of the construction cost, improvement of erection technology, and technology development for large-scale projects are subjects in the future. 22 refs., 8 figs., 1 tab.

  11. Modern techniques in prestressed concrete cable-stayed bridges. Puresutoresuto concrete shachokyo ni okeru atarashii gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, A. (Kobe Univ. (Japan). Faculty of Engineering)

    1994-03-31

    Because the prestressed concrete (PC) cable-stayed bridges combine the distinctive features such as a rationality of the structure or a structural beauty, it will not stay on a development of the technologies to make them longer and larger, and a rationalization of the execution, an investigation from various aspects such as the scenery design, material selection, pursuit of new structure and so forth will become necessary. In a main meeting, 15 volumes of paper on the most advanced technologies of PC cable-stayed bridges were presented. The presentations from Japan were 11 volumes, and occupied about 70%, and therefore a high interest to the PC cable-stayed bridges in Japan was inferred. In the presentation from Japan, there were many relevancies of the important study themes which would become a foundation for a development of PC cable-stayed bridges in the future, like ones that an improvement effect of dynamic behavior such as the aseismatic property, wind endurance and so forth was made as an objective, ones that a safety evaluation at an ultimate state as the oblique member anchoring part, main tower or entire structure was related, ones that a construction of the various control systems when the cable-stayed bridges were executed was concerned and so forth. 23 figs., 1 tab.

  12. Recent design methods for prestressed concrete cable stayed bridge; PC shachokyo no sekkei gijutsu no genjo

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, K. [Kajima Corp., Tokyo (Japan)

    1995-02-01

    The number of constructed prestressed concrete cable stayed bridges reached nearly 100 in Japan, and the technique has greatly developed. In this article, the current status of design techniques for prestressed concrete cable stayed bridges were introduced along with the examples of constructed bridges for the analysis method and the design method for each structure part while introducing the current examples of constructed bridges. Also, this kind of extra-dosed prestressed concrete bridge and prestressed concrete bridge with prestressed concrete stays were reported. Standards have been prepared including a chapter for the prestressed concrete cable stayed bridges in the Road Bridge Guideline document in February 1990. Load to be noticed as the characteristics peculiar to the prestressed concrete cable stayed bridges includes the shock due to live load, temperature change, and execution error of a tower. For example, 1/1000 of the total tower height is generally considered as the execution error of the tower. A diagonal member is manufactured at factories and in fields and has both advantages and disadvantages. The linear analysis of plane framework is general. Damping of and earthquakeproof designs against the wind and earthquake of the diagonal member were also provided. 11 refs., 17 figs., 2 tabs.

  13. Survey on the succession situation of technologies; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The basic survey was carried out to promote the succession and creative use of the previous industrial science and technology. The following 5 themes were summarized in fiscal 1993. On `Fuel technology policy and technological development,` Navy Fuel Depot, Chemical Research Institute at University of Kyoto, Central Laboratory of South Manchuria Railway Co., and Fuel Research Laboratory of the Ministry of Agriculture and Commerce played important roles, and the 1000atm continuous hydrogenation system was completed in 1941. On `Technology of long-distance power transmission,` high-voltage insulation technology finally reached an international level after World War II. On `Unification of frequency and electrical technology,` the two-frequency system for eastern and western areas was established before World War II, and construction of Sakuma Frequency Conversion Station allowed power interchange between two areas. On `Organization of national research laboratories,` the Agency of Industrial Science and Technology distinguished the roles of new and existing laboratories. On `Wind power technology in Europe and America,` comparison between American and Danish approaches is the most important issue today. 146 refs., 20 figs., 13 tabs.

  14. Evaluation technology of human behavior cognition; Ningen kodo ninchi hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For human engineering and improvement of the living environment, the evaluation technology of human behavior cognition was studied. For the future reformation and creation of economic structure, the following are required: establishment of safe and affluent communities, further improvement of the safety and harmonious balance of people, lives and society, and R & D close to people and social needs. Introduction of Product Liability law and a fail-safe concept are examples of such efforts. However, since many accidents are found in the human society, the relation between human errors and human characteristics should be studied in detail. The cognitive science of human behavior is an objective evaluation technology from the viewpoint of human being, object, environment and society. Based on these social and technological background, the feasibility of the evaluation technology is studied, and the future trend and skeleton of this project are clarified. The domestic and foreign trends of technologies concerned are thus surveyed, and the important points, features, skeleton and ripple effect of the technology are summarized. 500 refs., 70 figs., 5 tabs.

  15. Gas removal technique to maintain global environment. Chikyu kankyo hozen no tame no bojo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, K [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1992-10-12

    This paper describes the removal technique of gases such as CO2, SO2 and NOx which have the deep relation to the maintenance of global environment. This paper describes partially r SO2 and NOx which are the primary cause of acid rain. As for the removal of CO2 generated from fixed sources (thermal power stations and others), the separation technique and isolation-fixation technique have been researched on and developed. Of the separation method, the effect of the chemical absorption method and the adsorption method is proved with the preceding experiments. The isolation method is differently researched on as to store under deep sea or ground but may be urgent and temporary. The fixation of CO2 is a serious global problem which relates to the afforestation and forests. The fixation which uses coral reefs in ocean as the absorption source has a potential. As for the processing of substances causing acid rain, the desulfurization from petroleum and the flue gas desulfurization have the excellent results. The improvement of combustion method or the flue gas denitrification at the fixed sources are used to remove NOx. The removal of NOx from all diesel cars is difficult compared with the exhaust gas cleaning of gasoline cars and is not commercialized. 11 refs., 1 fig., 2 tabs.

  16. FY1995 studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; 1995 nendo handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of the semiconductor photocatalyst such as titanium dioxide is important for photo-energy conversion and purification of the environment. We make clear that the mechanism of the photocatalysis using a spectroscopic or physico-chemical methods, and we developed the new photocatalyst with the control of the surface area, porosity, infinitesimal content, and surface modification of the catalyst surface. Titanium dioxide thin film photocatalysts were prepared by the dip coating method. Surface structure of the thin film was formed by the aggregated TiO{sub 2} anatase particle, its size was around 5 nm. This thin films effectively oxidazed NO, its photocatalytic activity is higher than that of commercial photocatalyst. Metal oxide anchored TiO{sub 2} photocatalysts (RuO{sub 2}/TiO{sub 2}) were prepared by the co-precipitation method. Effective charge separation of the RuO{sub 2}/TiO{sub 2} were confirmed by the measurement of ESR. The RuO{sub 2}/TiO{sub 2} photocatalyst successfully reduced CO{sub 2} and preserved its activity for much longer period than metal loaded catalyst. Hybrid photofunctionalized material was prepared by anchoring porphyrin moieties on the titanium dioxide surface. The relative quantum yield of electron transfer from porphyrin to the titanium dioxide conduction band has been markedly increased by water treatment of quanternized porphyrin-titanium dioxide covalently linked systems owing to removal of adsorbed porphyrin domains. (NEDO)

  17. Customers` response to residential peak-activated pricing. Evidence from a Japanese experiment; Peak taio ryokinka ni okeru kateiyo juyoka no fuka chosei kodo no bunseki. Kansetsu fuka seigyo jikken data wo mochiita kakaku koka no sokutei

    Energy Technology Data Exchange (ETDEWEB)

    Asano, H. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-10-01

    Demand side management through a pricing mechanism, that is the indirect load control was experimented to analyze the pricing effect. When power consumption in indirect load control groups is compared between peak time band in weekdays in summer and off-the-peak time band, the power is less consumed when price gap is set than in a uniform charge time. When more number of persons is in home in daytime, room cooling is used in daytime including the peak band to adjust the demand. The substitution elasticity in price between demands in the peak time band and the off-the-peak time band is from about 0.06 to 0.07, which cannot be ignored. If the peak price is increased by four times, the demand in the peak band can be reduced by about 0.15 kW (when average power demand per household is assumed 0.75 kW). For room cooling devices, the first device is often installed in a living room and the second and further units in individual rooms such as bed rooms. The more the number of device, the higher the possibility that the use time band is outside the peak time band. This indirect load control experiment is a field test related to the peak-activated pricing for small power users, by which the users` behavior against the pricing effect was identified quantitatively. 5 refs., 1 fig., 8 tabs.

  18. FY1995 dynamically up-gradable machine based on right quality control and its life cycle support; 1995 nendo tekisei hinshitsu seigyo ni motozuku doteki seicho kikai to sono lifecycle shien

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A method for determining part re-use and recycling strategy in product design is considered for optimal design of total product life cycle based on the concept of Right Quality Products. For this purpose, it is important to be able to estimate part deterioration status under various product usage conditions. For supporting product designers' decision making about the product life cycle in preliminary design phase, the deterioration estimation is not required to be very exact, but to generate every possible deterioration modes qualitatively. Then, based on these deterioration modes, functional behaviour of target products is simulated, and possible product failure modes can be generated. By utilizing the FMEA (Failure Mode and Effect Analysis) method, the effects of failure modes are evaluated, and the results are fed back to product designers for confirming their design in terms of total product life cycle optimization. A basic methodology is considered, and case study has been done for a mechanical assembly of a one-time use camera. The assembly consists of injection molded parts. Various CAE methods have been used for predicting possible part failures due to initial residual stress, warp, fatigue, creep, and wear. Then kinematic and dynamic analysis of mechanical assembly has been done for detecting the effect of part deterioration on mechanism movements. Several critical failure modes have been detected, and the effects of those failures have been checked by the FMEA method. (NEDO)

  19. FY1995 study of the development of high resolution sub-surface fluid monitoring system using accurately controlled routine operated seismic system; 1995 nendo seimitsu seigyo shingen ni yoru chika ryutai koseido monitoring no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The development of new seismic sounding system based on the new concept of ACROSS (Accurately Controlled Routine-Operated Signal System) are aimed. The system includes not only new seismic sources but also the analyzing software specialize for the monitoring of the change in subsurface velocity structure, especially in the area of fluid resources. Powerful sources with good portability are strongly required for the practical data acquisition. Portable ACROSS sources (HIT) are developed. The system is mainly used to obtain the high resolution structure with relatively short penetration distance. The principal specifications are as follows: (1) 100Hz in maximum. (2) Linearly oscillating single force. This is generated by the combined two rotator moving opposite directions. (3) Variable force with little work. (4) Very simple source-ground coupler just put even on the soft ground. The system was operated at Yamagawa geothermal plant for two months. The result of the experiments are: (1) We confirmed the stability of the source over wide frequency range up to 100Hz. (2) We confirmed that amplitude and phase of ACROSS signal can be obtained very precisely. (3) Very small change of signal which arise from subsurface velocity change are detected. This indicates that the system can detect the slight velocity change due to variation of subsurface fluid system. (NEDO)

  20. FY1995 development of a clean CVD process by evaluation and control of gas phase nucleation phenomena; 1995 nendo kisokaku seisei gensho no hyoka to seigyo ni yoru clean CVD process no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this study is to develop a high-rate and clean chemical vapor deposition (CVD) process as a breakthrough technique to overcome the problems that particles generated in the gas phase during CVD process for preparation of functional thin films cause reduced product yield and deterioration of the films. In the CVD process proposed here, reactant gas and generated particles are electrically charged to control the motion of them with an electric field. In this study, gas-phase nucleation phenomena are evaluated both theoretically and experimentally. A high-rate, ionized CVD method is first developed, in which reactant gas and generated particles are charged with negative ions generated from a radioisotope source and the UV/photoelectron method, and the motion of the charged gas and particles is controlled with an electric field. Charging and transport processes of fine particles are then investigated experimentally and theoretically to develop a clean CVD method in which generated particles are removed with the electric forces. As a result, quantitative evaluation of the charging and transport process was made possible. We also developed devices for measuring the size distribution and concentration of fine particles in low pressure gas such as those found in plasma CVD processes. In addition, numerical simulation and experiments in this study for a TEOS/O{sub 3} CVD process to prepare thin films could determine reaction rates which have not been known so far and give information on selecting good operation conditions for the process. (NEDO)

  1. Development of mathematical model and optimal control system of internal temperatures of hot-blast stove process in staggered parallel operation; Netsufuro sushiki model to parallel sofu ni okeru ronai ondo saiteki seigyo system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Matoba, Y. [Sumitomo Metal Industries, Ltd., Osaka (Japan); Otsuka, K.

    1998-07-01

    A mathematical model and an optimal control system of hot-blast stove process are described. A precise mathematical simulation model of the hot-blast stove was developed and the accuracy of the model has been confirmed. An optimal control system of the thermal conditions of the hot-blast stoves in staggered parallel operation was also developed. By the use of the multivariable optimal regulator and the feedforward compensations for the change of the aimed blast temperature and blast volume, the system is able to control the hot blast temperature and the brick temperature efficiently. The system has been applied to Kashima works. The variations of the blast temperature and the silica brick temperature have been decreased. The ultimate low heat level operations have been realized and the thermal efficiency furthermore has been raised by about 1%. 8 refs., 14 figs., 1 tab.

  2. Frontier of nanometer devices. Part 6. New devices with fully controlled electrons and photons. Nanometa debaisu kenkyu saizensen. 6. Denshi to koshi no kanzen seigyo wo mezashita jisedai debaisu

    Energy Technology Data Exchange (ETDEWEB)

    Arakawa, Y [The Univ. of Tokyo, Tokyo (Japan). Inst. of Industrial Science

    1994-06-20

    In the nanotechnology to realize an artificial structure of a magnitude of atomic size, new electron devices and photon devices are aimed by confining electron and controlling the behavior of the electron with transition of a quantum mechanical state including a tunneling effect. The degree of freedom of electron decreased when electron is confined in a very small area within semiconductor and is 1 in a quantum wire while it is 0 in a quantum box. Energy level of electron is completely dispersed. The condition required to realize the nanometer structure is examined and the formation techniques of semiconductor nanometer structure are studied. This paper describes research results by the authors aiming to realize quantum wire and quantum box structures. Ultrafine pattern of SiO2 is formed by electron beam drawing technique followed by crystal growth with a MOCVD method to form the quantum wire and quantum box structures successfully. Laser oscillation is successful at 77K with optical pumping using a quantum wire and vertical micro resonator. 5 refs., 7 figs.

  3. Characteristic analysis of methane-gas generation by oxidizing heat of stored coal and hold ventilation control; Sekitan unpansen ni okeru sanka hatsunetsu ni yoru methane gas hassei to sonai kankyo seigyo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N; Nakashima, T [Kyushu Univ., Fukuoka (Japan); Kudo, S

    1999-12-31

    A demand of coal shows the tendency in the increase worldwide, with this, the marine transportation of the coal gradually increases, and the collier has also enlarged. The traffic pattern of coal is mainly the bulk transportation. In this transportation system, by the oxidation exothermic reaction of the coal, methane gas is produced, simultaneously the coal quality such as coking property or heat quantity is decreased and sometimes spontaneous ignition is caused. Therefore, it is necessary to equip with a ventilator to control the concentration of methane gas and to avoid the self heating of the coal. In this study, the quantity of methane-gas produced by heating coal using an electric furnace was measured and the experiment to investigate the temperature dependency of the methane-gas generated from the coal was conducted. By using the result of the measurement, the quantity of methane-gas produced from the coal stored in the hold of a coal cargo was estimated. And, the mathematical analyses on the changing degree depend on the times of a temperature in the hold under navigation, a concentration of oxygen and a concentration of methane-gas, were conducted. 11 refs., 19 figs., 2 tabs.

  4. Report on evaluation of research and development of light-aided instrumentation/control systems. Abstract; Hikari oyo keisoku seigyo system no kenkyu kaihatsu ni kansuru hyoka hokokusho. Gaiyohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-08-01

    This research and development project is aimed at commercialization of the light-aided instrumentation technology systems which safely, stably measure, transmit and control process information including image information, e.g., temperature, flow rates and components at large plants in industrial complexes, in the severe atmospheres in the presence of, e.g., electromagnetic induction and combustible gases. These optical systems need development of light transmitting/receiving devices, various optical devices that constitute the network nodes, and various types of sensors of improved functions and reliability, in addition to development of the techniques required for transmitting large quantities of information on a large scale. This project has attempted to systematically make break-through in the individual elementary techniques, in particular those in the widely diversified technological areas for the advanced devices, and thereby to expand the instrumentation/control technology frontiers. The results of studies on gallium/arsenic crystals, which are prerequisite for photoelectronic integrated circuits as the bases for the light application technology, and processes for producing thereof are highly rated worldwide. It is planned to effectively utilize the total system, constructed at then Nippon Mining's Mizushima Refinery, and thereby to establish the effective instrumentation techniques for commercial plants and to promote commercialization of these results. (NEDO)

  5. Research and development of a superconducting flywheel power storage system in fiscal 1998. Research and development of rotation control technology; 1998 nendo koon chodendo flywheel denryoku chozo kenkyu kaihatsu. Kaiten seigyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Element technology research was performed on 'rotation control' aimed at practical application of a 10-MW class high-temperature superconducting flywheel power storage system. As part of the research, researches were carried out on small-size and middle-size models, low-loss control type magnetic bearing, and large-size models. For the small-size model, as a result of performing performance tests on the protective bearing by using a testing machine, it was revealed that the model is free of problems in the test for up to 5000 rpm. For the middle-size model, fabrication and installation were completed on a middle-size rotation control testing equipment having CFRP-made flywheel with a diameter of 1 m. In the control type bearing, as a result of adopting a homo-polar type magnetic pole, the rotation loss was reduced to about 1/5 of that of a hetero-polar type. The amount is about 75 W (12000 rpm) when the bias current is 1.5 A. Concept design was implemented on a 2-MWh flywheel bearing system supported with a high-temperature superconducting magnetic bearing as a full-size flywheel. The CFRP-made flywheel has a diameter of 4 m, and a circumferential velocity of 1200 m. (NEDO)

  6. Development II of ion current combustion control system. Application to the lean burn system of the micro vehicle engine; Ion denryu wo mochiita nensho seigyo system no kaihatsu. 2. Keijidosha engine wo mochiita lean burn eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Iida, T; Asano, M; Kajitani, M; Kuma, t; Morinaga, Y [Daihatsu Motor Co. Ltd., Osaka (Japan)

    1997-10-01

    The lean bum engine has not been introduced into the micro vehicle so far because of the low cost requirement and small displacement, in spite of it is one of the effective solutions which increase the fuel economy. By the way, we had already reported in the former paper that we developed the ion current combustion control system the architecture of which is cheaper than the other system. In this paper, we described the way how the above system is applied to the lean burn system of the micro vehicle engine and also we reported the gain of fuel economy and the exhaust emission level. 5 refs., 11 figs., 2 tabs.

  7. FY 1998 annual report on the demonstration tests for establishing load concentration controlling systems. Survey on safety of commercial systems; Fuka shuchu seigyo system kakuritsu jissho shiken 1998 nendo kenkyu hokokusho. Jjitsuyo system anzensei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The demonstration tests are being conducted for establishing load concentration controlling systems, which directly or indirectly control load devices in residential power consumers or the like from a power supplier, as one of the DSM measures. This project is aimed at survey on the systems which support general residential consumers or the like to adequately contr