Technical area status report for low-level mixed waste final waste forms

International Nuclear Information System (INIS)

Mayberry, J.L.; DeWitt, L.M.; Darnell, R.

1993-08-01

The Final Waste Forms (FWF) Technical Area Status Report (TASR) Working Group, the Vitrification Working Group (WG), and the Performance Standards Working Group were established as subgroups to the FWF Technical Support Group (TSG). The FWF TASR WG is comprised of technical representatives from most of the major DOE sites, the Nuclear Regulatory Commission (NRC), the EPA Office of Solid Waste, and the EPA's Risk Reduction Engineering Laboratory (RREL). The primary activity of the FWF TASR Working Group was to investigate and report on the current status of FWFs for LLNM in this TASR. The FWF TASR Working Group determined the current status of the development of various waste forms described above by reviewing selected articles and technical reports, summarizing data, and establishing an initial set of FWF characteristics to be used in evaluating candidate FWFS; these characteristics are summarized in Section 2. After an initial review of available information, the FWF TASR Working Group chose to study the following groups of final waste forms: hydraulic cement, sulfur polymer cement, glass, ceramic, and organic binders. The organic binders included polyethylene, bitumen, vinyl ester styrene, epoxy, and urea formaldehyde. Section 3 provides a description of each final waste form. Based on the literature review, the gaps and deficiencies in information were summarized, and conclusions and recommendations were established. The information and data presented in this TASR are intended to assist the FWF Production and Assessment TSG in evaluating the Technical Task Plans (TTPs) submitted to DOE EM-50, and thus provide DOE with the necessary information for their FWF decision-making process. This FWF TASR will also assist the DOE and the MWIP in establishing the most acceptable final waste forms for the various LLMW streams stored at DOE facilities

76 FR 18624 - Research, Technical Assistance and Training Programs: Notice of Final Circular

Science.gov (United States)

2011-04-04

... to FTA Circular 6100.1D, Research and Technical Assistance Training Program: Application Instructions... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Research, Technical Assistance and Training Programs: Notice of Final Circular AGENCY: Federal Transit Administration (FTA), DOT. ACTION...

AIMES Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Katz, Daniel S [Univ. of Illinois, Urbana-Champaign, IL (United States). National Center for Supercomputing Applications (NCSA); Jha, Shantenu [Rutgers Univ., New Brunswick, NJ (United States); Weissman, Jon [Univ. of Minnesota, Minneapolis, MN (United States); Turilli, Matteo [Rutgers Univ., New Brunswick, NJ (United States)

2017-01-31

This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large-scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable and interoperable distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.

NCSU reactor sharing program. Final technical report

International Nuclear Information System (INIS)

Perez, P.B.

1997-01-01

The Nuclear Reactor Program at North Carolina State University provides the PULSTAR Research Reactor and associated facilities to eligible institutions with support, in part, from the Department of Energy Reactor Sharing Program. Participation in the NCSU Reactor Sharing Program continues to increase steadily with visitors ranging from advance high school physics and chemistry students to Ph.D. level research from neighboring universities. This report is the Final Technical Report for the DOE award reference number DE-FG05-95NE38136 which covers the period September 30, 1995 through September 30, 1996

High energy physics research. Final technical report, 1957--1994

International Nuclear Information System (INIS)

Williams, H.H.

1995-01-01

This is the final technical report to the Department of Energy on High Energy Physics at the University of Pennsylvania. It discusses research conducted in the following areas: neutrino astrophysics and cosmology; string theory; electroweak and collider physics; supergravity; cp violation and baryogenesis; particle cosmology; collider detector at Fermilab; the sudbury neutrino observatory; B-physics; particle physics in nuclei; and advanced electronics and detector development

High energy physics research. Final technical report, 1957--1994

Energy Technology Data Exchange (ETDEWEB)

Williams, H.H.

1995-10-01

This is the final technical report to the Department of Energy on High Energy Physics at the University of Pennsylvania. It discusses research conducted in the following areas: neutrino astrophysics and cosmology; string theory; electroweak and collider physics; supergravity; cp violation and baryogenesis; particle cosmology; collider detector at Fermilab; the sudbury neutrino observatory; B-physics; particle physics in nuclei; and advanced electronics and detector development.

Technical approach to finalizing sensible soil cleanup levels at the Fernald Environmental Management Project

International Nuclear Information System (INIS)

Carr, D.; Hertel, B.; Jewett, M.; Janke, R.; Conner, B.

1996-01-01

The remedial strategy for addressing contaminated environmental media was recently finalized for the US Department of Energy's (DOE) Fernald Environmental Management Project (FEMP) following almost 10 years of detailed technical analysis. The FEMP represents one of the first major nuclear facilities to successfully complete the Remedial Investigation/Feasibility Study (RI/FS) phase of the environmental restoration process. A critical element of this success was the establishment of sensible cleanup levels for contaminated soil and groundwater both on and off the FEMP property. These cleanup levels were derived based upon a strict application of Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) regulations and guidance, coupled with positive input from the regulatory agencies and the local community regarding projected future land uses for the site. The approach for establishing the cleanup levels was based upon a Feasibility Study (FS) strategy that examined a bounding range of viable future land uses for the site. Within each land use, the cost and technical implications of a range of health-protective cleanup levels for the environmental media were analyzed. Technical considerations in driving these cleanup levels included: direct exposure routes to viable human receptors; cross- media impacts to air, surface water, and groundwater; technical practicality of attaining the levels; volume of affected media; impact to sensitive environmental receptors or ecosystems; and cost. This paper will discuss the technical approach used to support the finalization of the cleanup levels for the site. The final cleanup levels provide the last remaining significant piece to the puzzle of establishing a final site-wide remedial strategy for the FEMP, and positions the facility for the expedient completion of site-wide remedial activities

Audit of Wolf Creek Generating Station, Unit 1 technical specifications. Final technical evaluation report

International Nuclear Information System (INIS)

Stromberg, H.M.

1985-07-01

This document was prepared for the Nuclear Regulatory Commission (NRC) to assist them in determining whether the Wolf Creek Generating Station Unit 1 Technical Specifications (T/S), which govern plant systems configurations and operations, are in conformance with the assumptions of the Final Safety Analysis Report (FSAR) as amended, the requirements of the Safety Evaluation Report (SER) as supplemented, and the Comments and Responses to the Wolf Creek Technical Specification Draft Inspection Report. A comparative audit of the FSAR as amended, the SER as supplemented, and the Draft Inspection Report was performed with the Wolf Creek T/S. Several discrepancies were identified and subsequently resolved through discussions with the cognizant NRC reviewer, NRC staff reviewers and/or utility representatives. The Wolf Creek Generating Station Unit 1 T/S, to the extent reviewed, are in conformance with the FSAR, SER, and Draft Inspection Report

78 FR 12955 - Final Requirements, Definitions, and Selection Criteria-Native American Career and Technical...

Science.gov (United States)

2013-02-26

... career and technical education programs (20 U.S.C. 2326(e)). This notice does not preclude us from... DEPARTMENT OF EDUCATION 34 CFR Chapter IV [Docket ID ED-2012-OVAE-0053] Final Requirements, Definitions, and Selection Criteria--Native American Career and Technical Education Program (NACTEP) [Catalog...

Technical planning activity: Final report

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

Technical planning activity: Final report

International Nuclear Information System (INIS)

1987-01-01

In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements

Technical area status report for low-level mixed waste final waste forms. Volume 1

Energy Technology Data Exchange (ETDEWEB)

Mayberry, J.L.; DeWitt, L.M. [Science Applications International Corp., Idaho Falls, ID (United States); Darnell, R. [EG and G Idaho, Inc., Idaho Falls, ID (United States)] [and others

1993-08-01

The Final Waste Forms (FWF) Technical Area Status Report (TASR) Working Group, the Vitrification Working Group (WG), and the Performance Standards Working Group were established as subgroups to the FWF Technical Support Group (TSG). The FWF TASR WG is comprised of technical representatives from most of the major DOE sites, the Nuclear Regulatory Commission (NRC), the EPA Office of Solid Waste, and the EPA`s Risk Reduction Engineering Laboratory (RREL). The primary activity of the FWF TASR Working Group was to investigate and report on the current status of FWFs for LLNM in this TASR. The FWF TASR Working Group determined the current status of the development of various waste forms described above by reviewing selected articles and technical reports, summarizing data, and establishing an initial set of FWF characteristics to be used in evaluating candidate FWFS; these characteristics are summarized in Section 2. After an initial review of available information, the FWF TASR Working Group chose to study the following groups of final waste forms: hydraulic cement, sulfur polymer cement, glass, ceramic, and organic binders. The organic binders included polyethylene, bitumen, vinyl ester styrene, epoxy, and urea formaldehyde. Section 3 provides a description of each final waste form. Based on the literature review, the gaps and deficiencies in information were summarized, and conclusions and recommendations were established. The information and data presented in this TASR are intended to assist the FWF Production and Assessment TSG in evaluating the Technical Task Plans (TTPs) submitted to DOE EM-50, and thus provide DOE with the necessary information for their FWF decision-making process. This FWF TASR will also assist the DOE and the MWIP in establishing the most acceptable final waste forms for the various LLMW streams stored at DOE facilities.

77 FR 30512 - Native American Career and Technical Education Program; Final Waivers and Extension of Project...

Science.gov (United States)

2012-05-23

... DEPARTMENT OF EDUCATION Native American Career and Technical Education Program; Final Waivers and... American Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84... and Technical Education Program (NACTEP), the Secretary waives 34 CFR 75.250 and 75.261(c)(2) in order...

"Type Ia Supernovae: Tools for Studying Dark Energy" Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Woosley, Stan [Lick Observatory, San Jose, CA (United States); Kasen, Dan [Univ. of California, Berkeley, CA (United States)

2017-05-10

Final technical report for project "Type Ia Supernovae: Tools for the Study of Dark Energy" awarded jointly to scientists at the University of California, Santa Cruz and Berkeley, for computer modeling, theory and data analysis relevant to the use of Type Ia supernovae as standard candles for cosmology.

Key technical issues associated with a method of pulse compression. Final technical report

International Nuclear Information System (INIS)

Hunter, R.O. Jr.

1980-06-01

Key technical issues for angular multiplexing as a method of pulse compression in a 100 KJ KrF laser have been studied. Environmental issues studied include seismic vibrations man-made vibrations, air propagation, turbulence, and thermal gradient-induced density fluctuations. These studies have been incorporated in the design of mirror mounts and an alignment system, both of which are reported. A design study and performance analysis of the final amplifier have been undertaken. The pulse compression optical train has been designed and assessed as to its performance. Individual components are described and analytical relationships between the optical component size, surface quality, damage threshold and final focus properties are derived. The optical train primary aberrations are obtained and a method for aberration minimization is presented. Cost algorithms for the mirrors, mounts, and electrical hardware are integrated into a cost model to determine system costs as a function of pulse length, aperture size, and spot size

Technical procedures for water resources: Volume 3, Environmental Field Program, Deaf Smith County Site, Texas: Final draft

International Nuclear Information System (INIS)

1987-08-01

To ensure that the environmental field program comprehensively addresses the issues and requirements of the project, a site study plan (SSP) has been prepared for Water Resources (ONWI, 1987). This technical procedure (TP) has been developed to implement the field program described in the Water Resources Site Study Plan. This procedure provides the general method for the field collection of water and sediment samples from playa lakes using an Alpha horizontal type sampler or equivalent or a peristaltic pump for water and a KB-coring devise or ponar grab for sediments. The samples will be preserved and then shipped to a laboratory for analysis. The water quality and sediment samples will be collected as part of the surface-water quality field study described in the Site Plan for Water Resources. 15 refs., 5 figs., 3 tabs

The Michigan high-level radioactive waste program: Final technical progress report

International Nuclear Information System (INIS)

1987-01-01

This report comprises the state of Michigan's final technical report on the location of a proposed high-level radioactive waste disposal site. Included are a list of Michigan's efforts to review the DOE proposal and a detailed report on the application of geographic information systems analysis techniques to the review process

Final Technical Report, Wind Generator Project (Ann Arbor)

Energy Technology Data Exchange (ETDEWEB)

Geisler, Nathan [City of Ann Arbor, MI (United States)

2017-03-20

A Final Technical Report (57 pages) describing educational exhibits and devices focused on wind energy, and related outreach activities and programs. Project partnership includes the City of Ann Arbor, MI and the Ann Arbor Hands-on Museum, along with additional sub-recipients, and U.S. Department of Energy/Office of Energy Efficiency and Renewable Energy (EERE). Report relays key milestones and sub-tasks as well as numerous graphics and images of five (5) transportable wind energy demonstration devices and five (5) wind energy exhibits designed and constructed between 2014 and 2016 for transport and use by the Ann Arbor Hands-on Museum.

Iowa Hill Pumped Storage Project Investigations - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hanson, David [Sacramento Municipal Unitlity District, Sacramento, CA (United States)

2016-07-01

This Final Technical Report is a summary of the activities and outcome of the Department of Energy (DOE) Assistance Agreement DE-EE0005414 with the Sacramento Municipal Utility District (SMUD). The Assistance Agreement was created in 2012 to support investigations into the Iowa Hill Pumped-storage Project (Project), a new development that would add an additional 400 MW of capacity to SMUD’s existing 688MW Upper American River Hydroelectric Project (UARP) in the Sierra Nevada mountains east of Sacramento, California.

Admiralty Inlet Pilot Tidal Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Collar, Craig [Public Utility District No. 1 of Snohomish County, Everett, WA (United States)

2015-09-14

This document represents the final report for the Admiralty Inlet Pilot Tidal Project, located in Puget Sound, Washington, United States. The Project purpose was to license, permit, and install a grid-connected deep-water tidal turbine array (two turbines) to be used as a platform to gather operational and environmental data on tidal energy generation. The data could then be used to better inform the viability of commercial tidal energy generation from technical, economic, social, and environmental standpoints. This data would serve as a critical step towards the responsible advancement of commercial scale tidal energy in the United States and around the world. In late 2014, Project activities were discontinued due to escalating costs, and the DOE award was terminated in early 2015. Permitting, licensing, and engineering design activities were completed under this award. Final design, deployment, operation, and monitoring were not completed. This report discusses the results and accomplishments achieved under the subject award.

77 FR 30514 - Native Hawaiian Career and Technical Education Program; Final Waiver and Extension of Project Period

Science.gov (United States)

2012-05-23

... DEPARTMENT OF EDUCATION Native Hawaiian Career and Technical Education Program; Final Waiver and... Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84.259A... Technical Education Program (NHCTEP), the Secretary hereby waives 34 CFR 75.261(c)(2) in order to extend the...

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Schuur, Edward [Northern Arizona Univ., Flagstaff, AZ (United States); Luo, Yiqi [Univ. of Oklahoma, Norman, OK (United States)

2016-12-01

This final grant report is a continuation of the final grant report submitted for DE-SC0006982 as the Principle Investigator (Schuur) relocated from the University of Florida to Northern Arizona University. This report summarizes the original project goals, as well as includes new project activities that were completed in the final period of the project.

Characterization of the radon source in North-Central Florida. Final report part 1 -- Final project report; Final report part 2 -- Technical report

International Nuclear Information System (INIS)

1997-01-01

This report contains two separate parts: Characterization of the Radon Source in North-Central Florida (final report part 1 -- final project report); and Characterization of the Radon Source in North-Central Florida (technical report). The objectives were to characterize the radon 222 source in a region having a demonstrated elevated indoor radon potential and having geology, lithology, and climate that are different from those in other regions of the U.S. where radon is being studied. Radon availability and transport in this region were described. Approaches for predicting the radon potential of lands in this region were developed

A History of Pebbles and Silt – Fluvial Sediment Transport, Hydropower and Technical Expertise at the Austrian Danube and its Tributaries

Directory of Open Access Journals (Sweden)

Schoder Angelika

2016-08-01

Full Text Available The paper investigates experts’ perceptions of hydropower, sediment regime, and their interaction in the 20th century with an environmental historical approach, based on various case studies at both the Danube River and one of its tributaries, and on a review of contemporary literature authored by engineers. Results show that questions of sediment continuity have engaged planners of hydropower plants since the advent of this technology, and decisions were at any time influenced by multiple interests (navigation, electricity demand, nature conservation. In such an intricate fluvial landscape, phenomena like reservoir sedimentation and riverbed incision can be approached as “legacies” of past technical interventions, which limit the options of current and future river management.

Clean Energy Works Oregon Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jacob, Andria [City of Portland; Cyr, Shirley [Clean Energy Works

2013-12-31

In April 2010, the City of Portland received a $20 million award from the U.S. Department of Energy, as part of the Energy Efficiency and Conservation Block Grant program. This award was appropriated under the American Recovery and Reinvestment Act (ARRA), passed by President Obama in 2009. DOE’s program became known as the Better Buildings Neighborhood Program (BBNP). The BBNP grant objectives directed the City of Portland Bureau of Planning and Sustainability (BPS) as the primary grantee to expand the BPS-led pilot program, Clean Energy Works Portland, into Clean Energy Works Oregon (CEWO), with the mission to deliver thousands of home energy retrofits, create jobs, save energy and reduce carbon dioxide emissions.The Final Technical Report explores the successes and lessons learned from the first 3 years of program implementation.

Energy Impact Illinois - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Olson, Daniel [Senior Energy Efficiency Planner; Plagman, Emily [Senior Energy Planner; Silberhorn, Joey-Lin [Energy Efficiency Program Assistant

2014-02-18

Energy Impact Illinois (EI2) is an alliance of government organizations, nonprofits, and regional utility companies led by the Chicago Metropolitan Agency for Planning (CMAP) that is dedicated to helping communities in the Chicago metropolitan area become more energy efficient. Originally organized as the Chicago Region Retrofit Ramp-Up (CR3), EI2 became part of the nationwide Better Buildings Neighborhood Program (BBNP) in May 2010 after receiving a $25 million award from the U.S. Department of Energy (DOE) authorized through the American Recovery and Reinvestment Act of 2009 (ARRA). The program’s primary goal was to fund initiatives that mitigate barriers to energy efficiency retrofitting activities across residential, multifamily, and commercial building sectors in the seven-county CMAP region and to help to build a sustainable energy efficiency marketplace. The EI2 Final Technical Report provides a detailed review of the strategies, implementation methods, challenges, lessons learned, and final results of the EI2 program during the initial grant period from 2010-2013. During the program period, EI2 successfully increased direct retrofit activity in the region and was able to make a broader impact on the energy efficiency market in the Chicago region. As the period of performance for the initial grant comes to an end, EI2’s legacy raises the bar for the region in terms of helping homeowners and building owners to take action on the continually complex issue of energy efficiency.

Final Technical Report for DE-FG02-98ER45737

Energy Technology Data Exchange (ETDEWEB)

Ade, Harald W.

2018-04-24

Final Technical Report For DOE Grant No. DE-FG02-98ER45737 Development of a Scanning Transmission X-Ray Microscope Polymer Thin Films and Self Assembled Monolayers: Pattern Formation and Surface Interactions NEXAFS Microscopy and Resonant Scattering of Polymeric Materials Organic Heterojunction Devices: Structure, Composition, and Performance at <20 nm Resolution Fundamental Science of High Open Circuit Voltage Excitonic Solar Cells Control of Interface- and Mesoscopic Structure in High Performance Organic Solar Cells: Towards a Predictive Device Paradigm

Stream sediment sampling and analysis. Final report

International Nuclear Information System (INIS)

Means, J.L.; Voris, P.V.; Headington, G.L.

1986-04-01

The objectives were to sample and analyze sediments from upstream and downstream locations (relative to the Goodyear Atomic plant site) of three streams for selected pollutants. The three streams sampled were the Scioto River, Big Beaver Creek, and Big Run Creek. Sediment samples were analyzed for EPA's 129 priority pollutants (Clean Water Act) as well as isotopic uranium ( 234 U, 235 U, and 238 U) and technetium-99

Summary report of the final technical meeting on 'International Reactor Dosimetry File: IRDF-2002'

International Nuclear Information System (INIS)

Griffin, Patrick J.; Paviotti-Corcuera, R.

2003-10-01

Presentations, recommendations and conclusions of the Final Technical Meeting on 'International Reactor Dosimetry File: IRDF-2002' are summarized in this report. The main aims of this meeting were to discuss scientific and technical matters related to reactor dosimetry and to assign responsibilities for the preparation of the final version of the IRDF- 2002 library and the associated TECDOC. Tasks were assigned and deadlines were agreed. Participants emphasized that accurate and complete nuclear data for reactor dosimetry are essential to improve the assessment accuracies for reactor pressure vessel service lifetimes in nuclear power plants, as well as for other neutron metrology applications such as boron neutron capture therapy, therapeutic use of medical isotopes, nuclear physics measurements, and reactor safety applications. (author)

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments.

Science.gov (United States)

Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

2012-08-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the "substances" approach derived from the European methodology for assessing new substances placed on the market, and the "matrix" approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments "1" and "2" presented a low risk for the peripheral aquatic ecosystems while sediment "3

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Eggeman, Tim [ZeaChem Inc., Lakewood, CO (United States); O' Neill, Brian [ZeaChem Inc., Lakewood, CO (United States)

2016-08-17

ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was already in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive inhibitors

DE-FG02-04ER63746 FinalTechnicalReport

Energy Technology Data Exchange (ETDEWEB)

Lidstrom, M.E.

2009-09-05

This is the final technical report for a project involving the study of stress response systems in the radiation-resistant bacterium, Deinococcus radiodurans. Three stresses of importance for a mixed waste treatment strain were studied, heat shock, solvent shock, and phosphate starvation. In each case, specific genes involved in the ability to survive the stress were identified using a systems biology approach, and analysis of mutants was used to understand mechanisms. This study has led to increased understanding of the ways in which a potential treatment strain could be manipulated to survive multiple stresses for treatment of mixed wastes.

Mathematics Intensive Summer Session (MISS). Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

This final technical report appears in two parts: the report for the 1995 summer MISS program and the report for the 1996 summer MISS program. Copies of the US Department of Energy Pre-Freshman Enrichment Program 1995 Entry Form and 1996 Entry Form completed by all participants were sent to the Oak Ridge Institute for Science and Education in the fall of 1995 and 1996 respectively. Those forms are on file should they be needed. Attached also is a copy of the Summary of ideas for panel discussions, problem-solving sessions, or small group discussions presented at the Department of Energy Oak Ridge Institute for Science and Education Pre-Freshman Enrichment Program Project Directors Meeting held in San Antonio, TX, November 12--14, 1995.

Technical and economic assessment of solar hybrid repowering. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1978-09-01

Public Service Company of New Mexico (PNM) has performed a Technical and Economic Assessment of Solar Hybrid Repowering under funding by the Department of Energy (DOE), the Electric Power Research Institute (EPRI), Western Energy Supply and Transmission (WEST) Associates, and a number of southwestern utilities. Solar hybrid repowering involves placement of solar hardware adjacent to and connected to existing gas- and oil-fueled electric generation units to displace some of or all the fossil fuel normally used during daylight hours. The subject study assesses the technical economic viability of the solar hybrid repowering concept within the southwestern United States and the PNM system. This document is a final report on the study and its results. The study was divided into the six primary tasks to allow a systematic investigation of the concept: (1) market survey and cost/benefit analysis, (2) study unit selection, (3) conceptual design and cost estimates, (4) unit economic analysis, (5) program planning, future phases, and (6) program management. Reeves Station No. 2 at Albuquerque, New Mexico, was selected for repowering with a design goal of 50 percent (25 MWe). The solar system design is based on the 10 MW solar central receiver pilot plant preliminary design for Barstow, California. SAN--1608-4-2 contains the technical drawings. (WHK)

University of Maryland component of the Center for Multiscale Plasma Dynamics: Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Dorland, William [University of Maryland

2014-11-18

The Center for Multiscale Plasma Dynamics (CMPD) was a five-year Fusion Science Center. The University of Maryland (UMD) and UCLA were the host universities. This final technical report describes the physics results from the UMD CMPD.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bohdan W. Oppenheim; Rudolf Marloth

2007-10-26

Executive Summary The document contains Final Technical Report on the Industrial Assessment Center Program at Loyola Marymount University in Los Angeles, covering the contract period of 9/1/2002 to 11/30/2006, under the contract DE-FC36-02GO 12073. The Report describes six required program tasks, as follows: TASK 1 is a summary of the assessments performed over the life of the award: 77 assessments were performed, 595 AR were recommended, covering a very broad range of manufacturing plants. TASK 2 is a description of the efforts to promote and increase the adoption of assessment recommendations and employ innovative methods to assist in accomplishing these goals. The LMU IAC has been very successful in accomplishing the program goals, including implemented savings of $5,141,895 in energy, $10,045,411 in productivity and $30,719 in waste, for a total of $15,218,025. This represents 44% of the recommended savings of $34,896,392. TASK 3 is a description of the efforts promoting the IAC Program and enhancing recruitment efforts for new clients and expanded geographic coverage. LMU IAC has been very successful recruiting new clients covering Southern California. Every year, the intended number of clients was recruited. TASK 4 describes the educational opportunities, training, and other related activities for IAC students. A total of 38 students graduated from the program, including 2-3 graduate students every semester, and the remainder undergraduate students, mostly from the Mechanical Engineering Department. The students received formal weekly training in energy (75%) and productivity (25). All students underwent extensive safety training. All students praised the IAC experience very highly. TASK 5 describes the coordination and integration of the Center activities with other Center and IAC Program activities, and DOE programs. LMU IAC worked closely with MIT, and SDSU IAC and SFSU IAC, and enthusiastically supported the SEN activities. TASK 6 describes other tasks

Nagra technical report 14-02, Geological basics - Dossier VI - Barrier properties of proposed host rock sediments and neighbouring rock; SGT Etappe 2: Vorschlag weiter zu untersuchender geologischer Standortgebiete mit zugehörigen Standortarealen für die Oberflächenanlage -- Geologische Grundlagen -- Dossier VI -- Barriereneigenschaften der Wirt- und Rahmengesteine

Energy Technology Data Exchange (ETDEWEB)

Gautschi, A.; Deplazes, G.; Traber, D.; Marschall, P. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Mazurek, M.; Gimmi, T.; Maeder, U. [Institute of Geological Sciences, University of Berne, Berne (Switzerland)

2014-12-15

This dossier is the sixth of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It discusses the barrier properties of the proposed host rock sediments and neighbouring rock layers. The mineralogical composition of the host rocks are discussed as are their pore densities and hydrological properties. Diffusion aspects are discussed. The aquifer systems in the proposed depository areas and their classification are looked at. The barrier properties of the host rocks and those of neighbouring sediments are discussed. Finally, modelling concepts and parameters for the transport of radionuclides in the rocks are discussed.

Geotechnical Survey, Dredgeability Of Soil Sediments And Siltation ...

African Journals Online (AJOL)

Geotechnical Survey, Dredgeability Of Soil Sediments And Siltation Volume Of Brimsu Water Reservoir. ... of the sediments was characterized by geo-technical descriptor terms, indicating that the sediments could be dredged using cutter-type dredger for excava-tion, and transported by hydraulic pipelines to disposal sites.

Remediation of heavy-metal contaminated sediments by means of bioleaching. Study: project results - economic efficiency - market assessment. Final report; Reinigung schwermetallbelasteter Sedimente durch Bioleaching. Studie: Projektergebnisse - Wirtschaftlichkeit - Marktbewertung. Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Loeser, C; Zehnsdorf, A; Hoffmann, P; Seidel, H; Schmerold, R

2002-07-01

Sediments in running and stationary waters continue to pose environmental as well as cost problems. In Saxonian waters alone some 3.7 million m{sup 3} of sediments mostly contaminated with heavy metals from mining or industrial activities are in need of remediation. For lack of practicable remediation methods excavated sediments nowadays are landfilled. However, due to its persisting hazard potential this solution is ecologically unsatisfactory. Exposure of these sediments to oxygen leads to microbial oxidation and acidification processes and hence partial solubilisation of heavy metals. If allowed to proceed uncontrolled this natural bioleaching process poses an environmental hazard. However, if accelerated artificially through activation of autochtonous sulphur oxidising bacteria (e.g. thiobacilli) it can be used to remediate sediments. The goal is to provide a semi-natural sediment decontamination process based on natural biological solubilisation potentials After decontamination, sediments can be returned to the materials cycle as soil substrates. The present process was developed using heavily contaminated sediments from the Weisse Elster region south of Leipzig as example material. For economic reasons it was decided to use a fixed-bed leaching process based on percolation. It proved necessary to use a multistage process. The laboratory and technical-scale experiments were dedicated to developing and implementing measures for faster metal solubilisation. [German] Gewaessersedimente sind ein bisher ungeloestes Umwelt- und Kostenproblem. Allein aus den Gewaessern Sachsens muessen ca. 3,7 Millionen m{sup 3} Sedimente beraeumt werden, diese sind zum grossen Teil mit Schwermetallen aus bergbaulichen und industriellen Aktivitaeten belastet. Gegenwaertig werden die ausgebaggerten Sedimente deponiert, da praktikable Sanierungsverfahren fehlen. Die Deoponierung ist wegen des weiter bestehenden Gefaehrdungspotentials keine oekologisch befriedigende Loesung. Kommen die

Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS): Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

de Boer, Gijs [Univ. of Colorado, Boulder, CO (United States); Lawrence, Dale [Univ. of Colorado, Boulder, CO (United States); Palo, Scott [Univ. of Colorado, Boulder, CO (United States); Argrow, Brian [Univ. of Colorado, Boulder, CO (United States); LoDolce, Gabriel [Univ. of Colorado, Boulder, CO (United States); Curry, Nathan [Univ. of Colorado, Boulder, CO (United States); Weibel, Douglas [Univ. of Colorado, Boulder, CO (United States); Finamore, William [Univ. of Colorado, Boulder, CO (United States); D' Amore, Phillip [Univ. of Colorado, Boulder, CO (United States); Borenstein, Steven [Univ. of Colorado, Boulder, CO (United States); Nichols, Tevis [Univ. of Colorado, Boulder, CO (United States); Elston, Jack [Blackswift Technologies, Boulder, CO (United States); Ivey, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bendure, Albert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schmid, Beat [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Long, Charles [Univ. of Colorado, Boulder, CO (United States); Telg, Hagen [Univ. of Colorado, Boulder, CO (United States); Gao, Ru-Shan [National Oceanic and Atmospheric Administration (NOAA), Boulder, CO (United States); Hock, Terry [National Center for Atmospheric Research, Boulder, CO (United States); Bland, Geoff [NASA Ames Research Center (ARC), Moffett Field, Mountain View, CA (United States)

2017-03-29

This final technical report details activities undertaken as part of the referenced project. Included is information on the preparation of aircraft for deployment to Alaska, summaries of the three deployments covered under this project, and a brief description of the dataset and science directions pursued. Additionally, we provide information on lessons learned, publications, and presentations resulting from this work.

Final Technical Report for contract number DE-FG02-05ER15670

Energy Technology Data Exchange (ETDEWEB)

Glazebrook, Jane [Univ. of Minnesota, Minneapolis, MN (United States)

2016-02-29

This is the final technical report for contract number DE-FG02-05ER15670. The project is now complete, and results of the project have been published. Two papers were published based on work done in the last three-year funding period. The DOIs of these papers are included below. The abstracts of the papers, providing summaries of the work, are included in the body of the report.

Sediment problems in reservoirs. Control of sediment deposits

Energy Technology Data Exchange (ETDEWEB)

Jacobsen, Tom

1997-12-31

When a reservoir is formed on a river, sediment will deposit in the reservoir. Such processes are unfortunate, for instance, for the implementation of hydroelectric energy. This thesis studies the problem of reservoir sedimentation and discusses methods of removing the sediments. Various aspects of reservoir sedimentation are discussed. Anthropogenic impacts seem to greatly affect the erosion processes. Temporal distribution is uneven, mainly because of the very large flood events. A world map showing the Reservoir Capacity: Annual Sediment Inflow ratio for reservoirs with volume equal to 10% of annual inflow has been prepared. The map shows that sedimentation is severe in the western parts of North and South America, eastern, southern and northern Africa, parts of Australia and most of Asia. The development of medium-sized reservoirs is difficult, as they are too large for conventional flushing technique and too small to store the sediment that accumulates during their economic lifetime. A computer model, SSIIM, was used with good results in a case study of two flood drawdown trials in Lake Roxburg, New Zealand. Two techniques have been developed that permits controlled suction of sediment and water into a pipe: the Slotted Pipe Sediment Sluicer (SPSS) and the Saxophone Sediment Sluicer (SSS). The techniques exploit the inflow pattern in through a slot in a pipe. An equation describing this inflow pattern was derived and verified experimentally. The SPSS is fixed near the reservoir bed, and sediment that deposits on top of it is removed in the sluicing process. The SSS sluices sediment from the surface of the sediment deposits. Some technical and economic conditions affecting the economics of sediment removal from reservoirs have been identified and studied. 79 refs., 112 figs., 14 tabs.

Technical and logistic provisions for the delivery of radioactive wastes in the final repository Konrad

International Nuclear Information System (INIS)

Poeppinghaus, Jens

2013-01-01

The beginning of radioactive waste delivery to the final repository Konrad is planned for 2019. The main issue for the technical and logistic provisions is the development of a concept for the transport of the licensed radioactive waste containers to the site, including a turning concept for cylindrical waste forms and planning, construction and manufacture of transport equipment. Further issues include a logistic concept considering specific boundary conditions as administrative processes, priorities, special features of the delivering institutions and technical requirements of the repository.

Final report for 105-N Basin sediment disposition task, phase 2 samples BOMPC8 and BOMPC9

International Nuclear Information System (INIS)

Esch, R.A.

1998-01-01

This document is the final report deliverable for Phase 2 analytical work for the 105-N Basin Sediment Disposition Task. On December 23, 1997, ten samples were received at the 222-S Laboratory as follows: two (2) bottles of potable water, six (6) samples for process control testing and two (2) samples for characterization. Analyses were performed in accordance with the Letter of Instruction for Phase 2 Analytical Work for the 105-N Basin Sediment Disposition Task (Logan and Kessner, 1997) (Attachment 7) and 105-N Basin Sediment Disposition Phase-Two Sampling and Analysis Plan (SAP) (Smith, 1997). The analytical results are included in Table 1. This document provides the values of X/Qs for the onsite and offsite receptors, taking into account the building wake and the atmospheric stability effects. X/Qs values for the potential fire accident were also calculated. In addition, the unit dose were calculated for the mixtures of isotopes

Correlated charge-changing uion-atom collisions. Final Technical Report

International Nuclear Information System (INIS)

John Tanis

2005-01-01

This document comprises the final technical report for atomic collisions research supported by DOE grant No. DE-FG02-87ER13778 from September 1, 2001 through August 31, 2004. The research involved the experimental investigation of excitation and charge-changing processes occurring in ion-atom and ion-molecule collisions. Major emphases of the study were: (1) interference effects resulting from coherent electron emission in H2, (2) production of doubly vacant K-shell (hollow ion) states due to electron correlation, and (3) formation of long-lived metastable states in electron transfer processes. During the period of the grant, this research resulted in 23 publications, 12 invited presentations, and 39 contributed presentations at national and international meetings and other institutions. Brief summaries of the completed research are presented below

FERMI(at)Elettra FEL Design Technical Optimization Final Report

International Nuclear Information System (INIS)

Fawley, William; Penn, Gregory; Allaria, Enrico; De Ninno, Giovanni; Graves, William

2006-01-01

This is the final report of the FEL Design Group for the Technical Optimization Study for the FERMI(at)ELETTRA project. The FERMI(at)ELETTRA project is based on the principle of harmonic upshifting of an initial ''seed'' signal in a single pass, FEL amplifier employing multiple undulators. There are a number of FEL physics principles which underlie this approach to obtaining short wavelength output: (1) the energy modulation of the electron beam via the resonant interaction with an external laser seed (2) the use of a chromatic dispersive section to then develop a strong density modulation with large harmonic overtones (3) the production of coherent radiation by the microbunched beam in a downstream radiator. Within the context of the FERMI project, we discuss each of these elements in turn

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments

Energy Technology Data Exchange (ETDEWEB)

Perrodin, Yves, E-mail: perrodin@entpe.fr [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Donguy, Gilles [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Bazin, Christine [INSAVALOR, 20 avenue Albert Einstein, 69621 Villeurbanne Cedex (France); Volatier, Laurence; Durrieu, Claude [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); Bony, Sylvie; Devaux, Alain [Universite de Lyon, ENTPE, CNRS, UMR 5023 LEHNA, 2 rue Maurice Audin, 69518 Vaulx-en-Velin (France); INRA, USC IGH, UMR LEHNA, 2, rue Maurice Audin, 69518 Vaulx-en-Velin (France); Abdelghafour, Mohammed; Moretto, Robert [INSAVALOR, 20 avenue Albert Einstein, 69621 Villeurbanne Cedex (France)

2012-08-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the 'substances' approach derived from the European methodology for assessing new substances placed on the market, and the 'matrix' approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, Horizontal-Ellipsis ). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments '1' and '2' presented a low risk for

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments

International Nuclear Information System (INIS)

Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

2012-01-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the “substances” approach derived from the European methodology for assessing new substances placed on the market, and the “matrix” approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments “1” and “2” presented a low risk for the peripheral aquatic ecosystems while

SIMS study on statistics and environmental factors in health. Final technical report to Department of Energy

International Nuclear Information System (INIS)

1982-07-01

This final technical report to DOE consists of five individual technical reports and one working paper by members of the SIMS Study at Stanford. Research topics include testing goodness-of-fit for the distribution of errors in regression models, mathematical models of cancer and their use in risk assessment, pollutant standards index (Psi), osteosarcomas among beagles exposed to 239 Plutonium, air pollution and respiratory disease, and models of human exposure to air pollution. Individual summaries of the six reports are indexed separately

Final Technical Report DOE/GO/13142-1

Energy Technology Data Exchange (ETDEWEB)

Patrick Mulvihill; Quang Nguyen

2010-09-15

This research adds to the understanding of the areas of residual starch and biomass conversion to alcohol, by providing data from pilot plant equipment of larger scale than the minimum required to give commercially scalable data. Instrumentation and control is in place to capture the information produced, for economic and technical evaluation. The impact of rheology, recycle streams, and residence time distributions on the technical and economic performance can be assessed. Various processes can be compared technically and economically because the pilot plants are readily modifiable. Several technologies for residual starch yield improvement have been identified, implemented, and patent applications filed. Various biomass-to-ethanol processes have been compared and one selected for technical optimization and commercialization. The technical and economic feasibility of the current simplified biomass conversion process is being confirmed by intensive pilot plant efforts as of this writing. Optimization of the feedstock handling and pretreatment is occurring to increase the alcohol yield above the minimum commercially viable level already demonstrated. Samples of biomass residue and reactor blowdown condensate are being collected to determine the technical and economic performance of the high-water-recycle waste treatment system being considered for the process. The project is of benefit to the public because it is advancing the efforts to achieve low-cost fermentable substrates for conversion to transportation fuels. This process combines the hydrolysis of agricultural residues with novel enzymes and organisms to convert the sugars released to transportation fuels. The process development is taking place at a scale allowing commercial development to proceed at a rapid pace.

Review of sediment stabilisation techniques. Final report

Energy Technology Data Exchange (ETDEWEB)

1992-12-31

The best sites for tidal power schemes are found in estuaries with high tidal ranges which have complex ecosystems and include a wide and diverse range of habitats. If the tidal power is to be developed, therefore, it is important to determine the likely effect on the environment and any ameliorative measures which may be necessary. One possible change is likely to be the erosion of material from the bed or shoreline of the estuary, and possibly the adjacent coast. This is of particular concern if intertidal sandflats, mudflats and saltmarsh are affected, as these are important wildlife habitats. Moreover, largescale movement of sediments would be undesirable. Results of a desk study of methods of preventing the erosion of sediment deposits in or near an estuary in the conditions that may occur following the construction of a tidal power barrage are presented. (author).

Sedimentation technique of waste bituminization and thermogravimetric characteristics of the final products

International Nuclear Information System (INIS)

Zeger, J.; Knotik, K.; Jakusch, H.

1976-01-01

In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GmbH a semi-technical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant uses a new technological process for embedding. One of the important features of this new process is that the solution water, which is normally inactive, is distilled off before embedding, resulting in dry and powdery salts. The second important feature is that these dry salts are mixed with the thin fluid bitumen by sedimentation. A special feature is that there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant was carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. It was shown that only nitrate and nitrite, especially in combination with Fe(III)-ions, are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410 0 C (above the melting point of both NaNO 2 and NaNO 3 ). The Fe-ions have a catalytic influence, as it could be shown that a 1% addition of Fe(NO 3 ) 3 to NaNO 3 leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extent by a hydrolysis before the embedding. There is, however, no danger to the embedding process from these effects since the process temperature of maximum 200 0 C is well below the ignition temperatures. A method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture has been developed. This is done by making two measurements with glass dose-meters, one with a beta-absorber to get a pure gamma dose and the other without it to get the combined beta and gamma dose. During the first measurement the dose-meters were protected against contamination by a thin layer of rubber

Evaluating Sediment Mobility for Siting Nearshore Berms

Science.gov (United States)

2016-04-01

placement of dredged sediment that may contain more fine silts and clays than are allowed for placement directly on the beach. The United States Army...used in the density and viscosity calculations. For this technical note an example study site is selected and the sediment mobility indexes are...acceleration due to gravity, sρ is the sediment density, ρ is the water density, v is the kinematic viscosity of water, crθ is the Shields

DOE FINAL TECHNICAL REPORT RP

Energy Technology Data Exchange (ETDEWEB)

RUSS PETERMAN

2012-01-01

The City of Georgetown Utility Systems (GUS) patnered with the private sector, the American Public Power Association (APPA) and Southwestern University to design, construct, test and monitor a solar co-generation system directly connected to the GUS electric distribution system. This report consists of the Primary Technical Report and 3 attachments.

Technical support document for the surface disposal of sewage sludge. Final report

International Nuclear Information System (INIS)

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed

Technical support document for the surface disposal of sewage sludge. Final report

Energy Technology Data Exchange (ETDEWEB)

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the surface disposal of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in sewage sludge placed on surface disposal sites. The management practices associated with surface disposal are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through surface disposal are discussed.

Technical assistance contractor Management Plan. Final [report

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins & Beckwith Agra, Inc. (SHB Agra), and Geraghty & Miller, Inc. (G&M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC`s groundwater technical breadth and depth, so G&M was brought in to augment the team`s capabilities. The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC`s management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls.

Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

Energy Technology Data Exchange (ETDEWEB)

Kinney, Edward R. [University of Colorado, Boulder, CO

2014-09-12

This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

An Approach to Developing Independent Learning and Non-Technical Skills Amongst Final Year Mining Engineering Students

Science.gov (United States)

Knobbs, C. G.; Grayson, D. J.

2012-01-01

There is mounting evidence to show that engineers need more than technical skills to succeed in industry. This paper describes a curriculum innovation in which so-called "soft" skills, specifically inter-personal and intra-personal skills, were integrated into a final year mining engineering course. The instructional approach was…

Final Technical Report for SISGR: Ultrafast Molecular Scale Chemical Imaging

Energy Technology Data Exchange (ETDEWEB)

Hersam, Mark C. [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering; Guest, Jeffrey R. [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Guisinger, Nathan P. [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Hla, Saw Wai [Argonne National Lab. (ANL), Argonne, IL (United States). Center for Nanoscale Materials; Schatz, George C. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Seideman, Tamar [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Van Duyne, Richard P. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry

2017-04-10

The Northwestern-Argonne SISGR program utilized newly developed instrumentation and techniques including integrated ultra-high vacuum tip-enhanced Raman spectroscopy/scanning tunneling microscopy (UHV-TERS/STM) and surface-enhanced femtosecond stimulated Raman scattering (SE-FSRS) to advance the spatial and temporal resolution of chemical imaging for the study of photoinduced dynamics of molecules on plasmonically active surfaces. An accompanying theory program addressed modeling of charge transfer processes using constrained density functional theory (DFT) in addition to modeling of SE-FSRS, thereby providing a detailed description of the excited state dynamics. This interdisciplinary and highly collaborative research resulted in 62 publications with ~ 48% of them being co-authored by multiple SISGR team members. A summary of the scientific accomplishments from this SISGR program is provided in this final technical report.

DIMEC - Final Report

DEFF Research Database (Denmark)

Conrad, Finn

1997-01-01

Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF.......Final report of the research project DIMEC - Danish InfoMechatronic Control supported by the Danish Technical Research Council, STVF....

Final Technical Report: Hydrogen Codes and Standards Outreach

Energy Technology Data Exchange (ETDEWEB)

Hall, Karen I.

2007-05-12

This project contributed significantly to the development of new codes and standards, both domestically and internationally. The NHA collaborated with codes and standards development organizations to identify technical areas of expertise that would be required to produce the codes and standards that industry and DOE felt were required to facilitate commercialization of hydrogen and fuel cell technologies and infrastructure. NHA staff participated directly in technical committees and working groups where issues could be discussed with the appropriate industry groups. In other cases, the NHA recommended specific industry experts to serve on technical committees and working groups where the need for this specific industry expertise would be on-going, and where this approach was likely to contribute to timely completion of the effort. The project also facilitated dialog between codes and standards development organizations, hydrogen and fuel cell experts, the government and national labs, researchers, code officials, industry associations, as well as the public regarding the timeframes for needed codes and standards, industry consensus on technical issues, procedures for implementing changes, and general principles of hydrogen safety. The project facilitated hands-on learning, as participants in several NHA workshops and technical meetings were able to experience hydrogen vehicles, witness hydrogen refueling demonstrations, see metal hydride storage cartridges in operation, and view other hydrogen energy products.

Final Technical Report. Origins of subsurface microorganisms: Relating laboratory microcosm studies to a geologic time scale; FINAL

International Nuclear Information System (INIS)

Kieft, Thomas; Amy, Penny S.; Phillips, Fred M.

1998-01-01

This project was conducted as part of the Department of Energy's Deep Subsurface Science Program. It was part of a larger effort to determine the origins of subsurface microorganisms. Two hypotheses have been suggested for the origins of subsurface microorganisms: (1) microorganisms were deposited at the time of (or shortly after) geologic deposition of rocks and sediments (the in situ survival hypothesis), and (2) microorganisms have been transported from surface environments to subsurface rocks and sediments since the time of geologic deposition (transport hypothesis). These two hypotheses are not mutually exclusive. Depending on the geological setting, either one or both of these hypotheses may best explain microbial origins. Our project focused on the in situ survival hypothesis. We tested the hypothesis that microorganisms (individuals populations and communities) can survive long-term sequestration within subsurface sediments. Other objectives were to identify geologic conditions that favor long-term survival, identify physiological traits of microorganisms that favor long-term survival, and determine which groups of microorganisms are most likely to survive long-term sequestration in subsurface sediments. We tested this hypothesis using a combination of pure culture techniques in laboratory microcosms under controlled conditions and field experiments with buried subsurface sediments

Technical support document for land application of sewage sludge. Volume 1. Final report

International Nuclear Information System (INIS)

Jones, A.; Beyer, L.; Rookwood, M.; Pacenka, J.; Bergin, J.

1992-11-01

The document provides the technical background and justification for the U.S. Environmental Protection Agency's (EPA) final regulation (40 CFR Part 503) covering the land application of sewage sludge. The document summarizes current practices in land application and presents data supporting the risk assessment methodology used to derive human health and environmental risk-based limits for contaminants in land applied sewage sludge. The management practices associated with land application are outlined and the different pathways by which contaminants reach highly-exposed individuals (HEIs) through land application are discussed

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

Energy Technology Data Exchange (ETDEWEB)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

International Nuclear Information System (INIS)

Anderson, Scott; Baca, Georgina; O'Connor, Michael

2015-01-01

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is on the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

Energy Technology Data Exchange (ETDEWEB)

Anderson, Scott [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company; Baca, Georgina [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company; O' Connor, Michael [Lockheed Martin Corporation, Denver, CO (United States). Space Systems Company

2015-12-31

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is on the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.

Gravitational sedimentation of flocculated waste activated sludge.

Science.gov (United States)

Chu, C P; Lee, D J; Tay, J H

2003-01-01

The sedimentation characteristics of flocculated wastewater sludge have not been satisfactorily explored using the non-destructive techniques, partially owing to the rather low solid content (ca. 1-2%) commonly noted in the biological sediments. This paper investigated, for the first time, the spatial-temporal gravitational settling characteristics of original and polyelectrolyte flocculated waste activated sludge using Computerized Axial Tomography Scanner. The waste activated sludge possessed a distinct settling characteristic from the kaolin slurries. The waste activated sludges settled more slowly and reached a lower solid fraction in the final sediment than the latter. Flocculation markedly enhanced the settleability of both sludges. Although the maximum achievable solid contents for the kaolin slurries were reduced, flocculation had little effects on the activated sludge. The purely plastic rheological model by Buscall and White (J Chem Soc Faraday Trans 1(83) (1987) 873) interpreted the consolidating sediment data, while the purely elastic model by Tiller and Leu (J. Chin. Inst. Chem. Eng. 11 (1980) 61) described the final equilibrated sediment. Flocculation produced lower yield stress during transient settling, thereby resulting in the more easily consolidated sludge than the original sample. Meanwhile, the flocculated activated sludge was stiffer in the final sediment than in the original sample. The data reported herein are valuable to the theories development for clarifier design and operation.

Technical basis for the ITER final design report, cost review and safety analysis (FDR)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

The ITER final design report, cost review and safety analysis (FDR) is the 4th major milestone, representing the progress made in the ITER Engineering Design Activities. With the approval of the Detailed Design Report (DDR), the design work was concentrated on the requirements of operation, with only relatively minor changes to design concepts of major components. The FDR is the culmination of almost 6 years collaborative design and supporting technical work by the ITER Joint Central Team and Home Teams under the terms of the ITER EDA Agreement. Refs, figs, tabs

Technical basis for the ITER final design report, cost review and safety analysis (FDR)

International Nuclear Information System (INIS)

1998-01-01

The ITER final design report, cost review and safety analysis (FDR) is the 4th major milestone, representing the progress made in the ITER Engineering Design Activities. With the approval of the Detailed Design Report (DDR), the design work was concentrated on the requirements of operation, with only relatively minor changes to design concepts of major components. The FDR is the culmination of almost 6 years collaborative design and supporting technical work by the ITER Joint Central Team and Home Teams under the terms of the ITER EDA Agreement

Technical review of externalities issues. Final report

International Nuclear Information System (INIS)

Niemeyer, V.

1994-12-01

Externalities has become the catchword for a major experiment in electric utility regulation. Together with increased competition as a means for economic regulation, this experiment represents a potential revolution in how electric utilities are regulated. It is very important for utilities and policy makers to understand the technical issues and arguments driving the externality experiment. This Technical Review presents four papers covering topics in economics that may play important roles in this revolution. The four papers are: Economic Issues in the Application of Externalities to Electricity Resource Selection; Climate Change, the Marginal Cost of Carbon Dioxide Emissions and the Implications for Carbon Dioxide Emissions Adders; Positive Externalities and Benefits from Electricity; and Socioeconomic Effects of Externality Adders for Electric Utility Emissions

Technical study gas storage. Final report

International Nuclear Information System (INIS)

Borowka, J.; Moeller, A.; Zander, W.; Koischwitz, M.A.

2001-01-01

This study will answer the following questions: (a) For what uses was the storage facility designed and for what use is it currently applied? Provide an overview of the technical data per gas storage facility: for instance, what is its capacity, volume, start-up time, etc.; (b) How often has this facility been used during the past 10 years? With what purpose was the facility brought into operation at the time? How much gas was supplied at the time from the storage facility?; (c) Given the characteristics and the use of the storage facility during the past 10 years and projected gas consumption in the future, how will the storage facility be used in the future?; (d) Are there other uses for which the gas storage facility can be deployed, or can a single facility be deployed for numerous uses? What are the technical possibilities in such cases? Questions (a) and (b) are answered separately for every storage facility. Questions (c) and (d) in a single chapter each (Chapter 2 and 3). An overview of the relevant storage data relating to current use, use in the last 10 years and use in future is given in the Annex

78 FR 29239 - Final Priority; Technical Assistance To Improve State Data Capacity-National Technical Assistance...

Science.gov (United States)

2013-05-20

... Assistance To Improve State Data Capacity--National Technical Assistance Center To Improve State Capacity To... Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State... (FY) 2013 and later years. We take this action to focus attention on an identified national need to...

Final waste classification and waste form technical position papers

International Nuclear Information System (INIS)

1983-05-01

The waste classification technical position paper describes overall procedures acceptable to NRC staff which may be used by licensees to determine the presence and concentrations of the radionuclides listed in section 61.55, and thereby classifying waste for near-surface disposal. This technical position paper also provides guidance on the types of information which should be included in shipment manifests accompanying waste shipments to near-surface disposal facilities. The technical position paper on waste form provides guidance to waste generators on test methods and results acceptable to NRC staff for implementing the 10 CFR Part 61 waste form requirements. It can be used as an acceptable approach for demonstrating compliance with the 10 CFR Part 61 waste structural stability criteria. This technical position paper includes guidance on processing waste into an acceptable stable form, designing acceptable high-integrity containers, packaging cartridge filters, and minimizing radiation effects on organic ion-exchange resins. The guidance in the waste form technical position paper may be used by licensees as the basis for qualifying process control programs to meet the waste form stability requirements, including tests which can be used to demonstrate resistance to degradation arising from the effects of compression, moisture, microbial activity, radiation, and chemical changes. Generic test data (e.g., topical reports prepared by vendors who market solidification technology) may be used for process control program qualification where such generic data is applicable to the particular types of waste generated by a licensee

Technical note: False low turbidity readings from optical probes during high suspended-sediment concentrations

Science.gov (United States)

Voichick, Nicholas; Topping, David J.; Griffiths, Ronald E.

2018-03-01

Turbidity, a measure of water clarity, is monitored for a variety of purposes including (1) to help determine whether water is safe to drink, (2) to establish background conditions of lakes and rivers and detect pollution caused by construction projects and stormwater discharge, (3) to study sediment transport in rivers and erosion in catchments, (4) to manage siltation of water reservoirs, and (5) to establish connections with aquatic biological properties, such as primary production and predator-prey interactions. Turbidity is typically measured with an optical probe that detects light scattered from particles in the water. Probes have defined upper limits of the range of turbidity that they can measure. The general assumption is that when turbidity exceeds this upper limit, the values of turbidity will be constant, i.e., the probe is pegged; however, this assumption is not necessarily valid. In rivers with limited variation in the physical properties of the suspended sediment, at lower suspended-sediment concentrations, an increase in suspended-sediment concentration will cause a linear increase in turbidity. When the suspended-sediment concentration in these rivers is high, turbidity levels can exceed the upper measurement limit of an optical probe and record a constant pegged value. However, at extremely high suspended-sediment concentrations, optical turbidity probes do not necessarily stay pegged at a constant value. Data from the Colorado River in Grand Canyon, Arizona, USA, and a laboratory experiment both demonstrate that when turbidity exceeds instrument-pegged conditions, increasing suspended-sediment concentration (and thus increasing turbidity) may cause optical probes to record decreasing false turbidity values that appear to be within the valid measurement range of the probe. Therefore, under high-turbidity conditions, other surrogate measurements of turbidity (e.g., acoustic-attenuation measurements or suspended-sediment samples) are necessary to

Entrainment at a sediment concentration interface in turbulent channel flow

Science.gov (United States)

Salinas, Jorge; Shringarpure, Mrugesh; Cantero, Mariano; Balachandar, S.

2016-11-01

In this work we address the role of turbulence on entrainment at a sediment concentration interface. This process can be conceived as the entrainment of sediment-free fluid into the bottom sediment-laden flow, or alternatively, as the entrainment of sediment into the top sediment-free flow. We have performed direct numerical simulations for fixed Reynolds and Schmidt numbers while varying the values of Richardson number and particle settling velocity. The analysis performed shows that the ability of the flow to pick up a given sediment size decreases with the distance from the bottom, and thus only fine enough sediment particles are entrained across the sediment concentration interface. For these cases, the concentration profiles evolve to a final steady state in good agreement with the well-known Rouse profile. The approach towards the Rouse profile happens through a transient self-similar state. Detailed analysis of the three dimensional structure of the sediment concentration interface shows the mechanisms by which sediment particles are lifted up by tongues of sediment-laden fluid with positive correlation between vertical velocity and sediment concentration. Finally, the mixing ability of the flow is addressed by monitoring the center of mass of the sediment-laden layer. With the support of ExxonMobil, NSF, ANPCyT, CONICET.

Alumina reinforced tetragonal zirconia (TZP) composites. Final technical report, July 1, 1993--December 31, 1996

International Nuclear Information System (INIS)

Shetty, D.K.

1997-01-01

This final technical report summarizes the significant research results obtained during the period July 1, 1993 through December 31, 1996 in the DOE-supported research project entitled, open-quotes Alumina Reinforced Tetragonal Zirconia (TZP) Compositesclose quotes. The objective of the research was to develop high-strength and high-toughness ceramic composites by combining mechanisms of platelet, whisker or fiber reinforcement with transformation toughening. The approach used included reinforcement of Celia- or yttria-partially-stabilized zirconia (Ce-TZP or Y-TZP) with particulates, platelets, or continuous filaments of alumina

Combining sediment fingerprinting and a conceptual model for erosion and sediment transfer to explore sediment sources in an Alpine catchment

Science.gov (United States)

Costa, A.; Stutenbecker, L.; Anghileri, D.; Bakker, M.; Lane, S. N.; Molnar, P.; Schlunegger, F.

2017-12-01

In Alpine basins, sediment production and transfer is increasingly affected by climate change and human activities, specifically hydropower exploitation. Changes in sediment sources and pathways significantly influence basin management, biodiversity and landscape evolution. We explore the dynamics of sediment sources in a partially glaciated and highly regulated Alpine basin, the Borgne basin, by combining geochemical fingerprinting with the modelling of erosion and sediment transfer. The Borgne basin in southwest Switzerland is composed of three main litho-tectonic units, which we characterised following a tributary-sampling approach from lithologically characteristic sub-basins. We analysed bulk geochemistry using lithium borate fusion coupled with ICP-ES, and we used it to discriminate the three lithologic sources using statistical methods. Finally, we applied a mixing model to estimate the relative contributions of the three sources to the sediment sampled at the outlet. We combine results of the sediment fingerprinting with simulations of a spatially distributed conceptual model for erosion and transport of fine sediment. The model expresses sediment erosion by differentiating the contributions of erosional processes driven by erosive rainfall, snowmelt, and icemelt. Soil erodibility is accounted for as function of land-use and sediment fluxes are linearly convoluted to the outlet by sediment transfer rates for hillslope and river cells, which are a function of sediment connectivity. Sediment connectivity is estimated on the basis of topographic-hydraulic connectivity, flow duration associated with hydropower flow abstraction and permanent storage in hydropower reservoirs. Sediment fingerprinting at the outlet of the Borgne shows a consistent dominance (68-89%) of material derived from the uppermost, highly glaciated reaches, while contributions of the lower part (10-25%) and middle part (1-16%), where rainfall erosion is predominant, are minor. This result is

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Velasco, Mayda [Northwestern University

2013-11-01

This work is focused on the design and construction of novel beam diagnostic and instrumentation for charged particle accelerators required for the next generation of linear colliders. Our main interest is in non-invasive techniques. The Northwestern group of Velasco has been a member of the CLIC Test Facility 3 (CTF3) collaboration since 2003, and the beam instrumentation work is developed mostly at this facility1. This 4 kW electron beam facility has a 25-170 MeV electron LINAC. CTF3 performed a set of dedicated measurements to finalize the development of our RF-Pickup bunch length detectors. The RF-pickup based on mixers was fully commissioned in 2009 and the RF-pickup based on diodes was finished in time for the 2010-11 data taking. The analysis of all the data taken in by the summer of 2010 was finish in time and presented at the main conference of the year, LINAC 2010 in Japan.

State child health; revisions to the regulations implementing the State Children's Health Insurance Program. Interim final rule with comment period; revisions, delay of effective date, and technical amendments to final rule.

Science.gov (United States)

2001-06-25

Title XXI authorizes the State Children's Health Insurance Program (SCHIP) to assist State efforts to initiate and expand the provision of child health assistance to uninsured, low-income children. On January 11, 2001 we published a final rule in the Federal Register to implement SCHIP that has not gone into effect. This interim final rule further delays the effective date, revises certain provisions and solicits public comment, and makes technical corrections and clarifications to the January 2001 final rule based on further review of the comments received and applicable law. Only the provisions set forth in this document have changed. All other provisions set forth in the January 2001 final rule will be implemented without change.

Final priority. Rehabilitation Training: Job-Driven Vocational Rehabilitation Technical Assistance Center. Final priority.

Science.gov (United States)

2014-08-19

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Rehabilitation Training program to establish a Job-Driven Vocational Rehabilitation Technical Assistance Center (JDVRTAC). The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to focus on training in an area of national need. Specifically, this priority responds to the Presidential Memorandum to Federal agencies directing them to take action to address job-driven training for the Nation's workers. The JDVRTAC will provide technical assistance (TA) to State vocational rehabilitation (VR) agencies to help them develop for individuals with disabilities training and employment opportunities that meet the needs of today's employers.

Technical note: False low turbidity readings from optical probes during high suspended-sediment concentrations

Science.gov (United States)

Voichick, Nicholas; Topping, David; Griffiths, Ronald

2018-01-01

Turbidity, a measure of water clarity, is monitored for a variety of purposes including (1) to help determine whether water is safe to drink, (2) to establish background conditions of lakes and rivers and detect pollution caused by construction projects and stormwater discharge, (3) to study sediment transport in rivers and erosion in catchments, (4) to manage siltation of water reservoirs, and (5) to establish connections with aquatic biological properties, such as primary production and predator–prey interactions. Turbidity is typically measured with an optical probe that detects light scattered from particles in the water. Probes have defined upper limits of the range of turbidity that they can measure. The general assumption is that when turbidity exceeds this upper limit, the values of turbidity will be constant, i.e., the probe is pegged; however, this assumption is not necessarily valid. In rivers with limited variation in the physical properties of the suspended sediment, at lower suspended-sediment concentrations, an increase in suspended-sediment concentration will cause a linear increase in turbidity. When the suspended-sediment concentration in these rivers is high, turbidity levels can exceed the upper measurement limit of an optical probe and record a constant pegged value. However, at extremely high suspended-sediment concentrations, optical turbidity probes do not necessarily stay pegged at a constant value. Data from the Colorado River in Grand Canyon, Arizona, USA, and a laboratory experiment both demonstrate that when turbidity exceeds instrument-pegged conditions, increasing suspended-sediment concentration (and thus increasing turbidity) may cause optical probes to record decreasing false turbidity values that appear to be within the valid measurement range of the probe. Therefore, under high-turbidity conditions, other surrogate measurements of turbidity (e.g., acoustic-attenuation measurements or suspended-sediment samples

Final priority; Technical Assistance on State Data Collection--IDEA Data Management Center. Final priority.

Science.gov (United States)

2014-08-05

The Assistant Secretary for the Office of Special Education and Rehabilitative Services (OSERS) announces a priority under the Technical Assistance on State Data Collection program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to fund a cooperative agreement to establish and operate an IDEA Data Management Center (Center) that will provide technical assistance (TA) to improve the capacity of States to meet the data collection requirements of the Individuals with Disabilities Education Act (IDEA).

Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Saurwein, John

2011-07-15

This report is the Final Technical Report for the Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project conducted by a team led by General Atomics under DOE Award DE-NE0000245. The primary overall objective of the project was to develop and document a conceptual design for the Steam Cycle Modular Helium Reactor (SC-MHR), which is the reactor concept proposed by General Atomics for the NGNP Demonstration Plant. The report summarizes the project activities over the entire funding period, compares the accomplishments with the goals and objectives of the project, and discusses the benefits of the work. The report provides complete listings of the products developed under the award and the key documents delivered to the DOE.

Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project - Final Technical Report

International Nuclear Information System (INIS)

Saurwein, J.

2011-01-01

This report is the Final Technical Report for the Next Generation Nuclear Plant (NGNP) Prismatic HTGR Conceptual Design Project conducted by a team led by General Atomics under DOE Award DE-NE0000245. The primary overall objective of the project was to develop and document a conceptual design for the Steam Cycle Modular Helium Reactor (SC-MHR), which is the reactor concept proposed by General Atomics for the NGNP Demonstration Plant. The report summarizes the project activities over the entire funding period, compares the accomplishments with the goals and objectives of the project, and discusses the benefits of the work. The report provides complete listings of the products developed under the award and the key documents delivered to the DOE.

Imagining Technicities

DEFF Research Database (Denmark)

Liboriussen, Bjarke; Plesner, Ursula

2011-01-01

to the elements of taste and skill. In the final analysis those references were synthesized as five imagined technicities: the architect, the engineer, the client, the Chinese, and the Virtual World native. Because technicities are often assumed and rarely discussed as actants who influence practice, their role......, this article focuses on innovative uses of virtual worlds in architecture. We interviewed architects, industrial designers and other practitioners. Conceptually supported by an understanding of technicity found in Cultural Studies, the interviews were then coded with a focus on interviewees’ references...... in cooperation and development of ICTs seems to pass unnoticed. However, since they are aligned into ICTs, technicities impact innovation....

APPLICATION OF SEDIMENT QUALITY GUIDELINES IN THE ASSESSMENT OF MANGROVE SURFACE SEDIMENT IN MENGKABONG LAGOON, SABAH, MALAYSIA

Directory of Open Access Journals (Sweden)

S. M. Praveena, M. Radojevic, M. H. Abdullah, A. Z. Aris

2008-01-01

Full Text Available There have been numerous sediment quality guidelines developed to monitor the sediments. Sediment quality guidelines are very useful to screen sediment contamination by comparing sediment contaminant concentration with the corresponding quality guideline, provide useful tools for screening sediment chemical data to identify pollutants of concern and prioritise problem sites and relatively good predictors of contaminations. However, these guidelines are chemical specific and do not include biological parameters. Aquatic ecosystems, including sediments, must be assessed in multiple components (biological data, toxicity, physicochemistry by using intregrated approaches in order to establish a complete and comprehensive set of sediment quality guidelines. Numerous sediment quality guidelines Washington Department of Ecology Sediment Quality Guideline, Australian and New Zealand Environment and Conservation Council, Swedish Environmental Sediment Quality, Screening Quick Reference Table, Portuguese Legislation on the Classification of Dredged Materials in Coastal Zones and Interim Sediment Quality Guideline for Hong Kong have been applied to the Mengkabong lagoon mangrove sediment and discussed. The most appropriate guideline that meets the prioritization criteria consistent with international initiatives and regulations is interim sediment quality values for Hong Kong. The guideline verifies that all the metals are below the Interim Sediment Quality Value-low. However, site-specific, biological testing and ecological analysis of exisiting benthics community structure related to sediment contamination are needed for final decision making in the case of Mengkabong lagoon.

Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility; FINAL

International Nuclear Information System (INIS)

Thomas B. Kirchner

2002-01-01

The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

Dredging Operations Technical Support Program. Transformation, Fixation, and Mobilization of Arsenic and Antimony in Contaminated Sediments.

Science.gov (United States)

1984-01-01

and Edwards (1977) reported that whole cells of :ethaogenic bacteria in variod anaerobic environments ( rumen fluid, sewage sludge) nproduced...sediments were studied with emphasis placed on short- and long-term 14 leaching and sediment conditions that affect mobilization. -; Under anaerobic ...conditions, arsenate [As(V)] was reduced to arsenite [As(III)] in a wide range of sediments. In anaerobic Texas City sediment slur- ries, 70% of added As(V

Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors: Final Scientific/Technical Report

International Nuclear Information System (INIS)

Vierow, Karen; Aldemir, Tunc

2009-01-01

The project entitled, 'Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors', was conducted as a DOE NERI project collaboration between Texas A and M University and The Ohio State University between March 2006 and June 2009. The overall goal of the proposed project was to develop practical approaches and tools by which dynamic reliability and risk assessment techniques can be used to augment the uncertainty quantification process in probabilistic risk assessment (PRA) methods and PRA applications for Generation IV reactors. This report is the Final Scientific/Technical Report summarizing the project.

Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors: Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Vierow, Karen; Aldemir, Tunc

2009-09-10

The project entitled, “Uncertainty Quantification in the Reliability and Risk Assessment of Generation IV Reactors”, was conducted as a DOE NERI project collaboration between Texas A&M University and The Ohio State University between March 2006 and June 2009. The overall goal of the proposed project was to develop practical approaches and tools by which dynamic reliability and risk assessment techniques can be used to augment the uncertainty quantification process in probabilistic risk assessment (PRA) methods and PRA applications for Generation IV reactors. This report is the Final Scientific/Technical Report summarizing the project.

Programs of Study as a State Policy Mandate: A Longitudinal Study of the South Carolina Personal Pathways to Success Initiative. Final Technical Report: Major Findings and Implications

Science.gov (United States)

Hammond, Cathy; Drew, Sam F.; Withington, Cairen; Griffith, Cathy; Swiger, Caroline M.; Mobley, Catherine; Sharp, Julia L.; Stringfield, Samuel C.; Stipanovic, Natalie; Daugherty, Lindsay

2013-01-01

This is the final technical report from the National Research Center for Career and Technical Education's (NRCCTE's) five-year longitudinal study of South Carolina's Personal Pathway to Success initiative, which was authorized by the state's Education and Economic Development Act (EEDA) in 2005. NRCCTE-affiliated researchers at the National…

Development of a Transgenic Model to Assess Bioavailable Genotoxicity in Sediments

National Research Council Canada - National Science Library

1999-01-01

This technical note describes the rationale for using transgenic animal models to assess the potential genotoxicity of sediments, the benefits that can be obtained using such models versus currently...

Final Technical Report - Kotzebue Wind Power Project - Volume II

Energy Technology Data Exchange (ETDEWEB)

Rana Zucchi, Global Energy Concepts, LLC; Brad Reeve, Kotzebue Electric Association; DOE Project Officer - Doug Hooker

2007-10-31

The Kotzebue Wind Power Project is a joint undertaking of the U.S. Department of Energy (DOE); Kotzebue Electric Association (KEA); and the Alaska Energy Authority (AEA). The goal of the project is to develop, construct, and operate a wind power plant interconnected to a small isolated utility grid in an arctic climate in Northwest Alaska. The primary objective of KEA’s wind energy program is to bring more affordable electricity and jobs to remote Alaskan communities. DOE funding has allowed KEA to develop a multi-faceted approach to meet these objectives that includes wind project planning and development, technology transfer, and community outreach. The first wind turbines were installed in the summer of 1997 and the newest turbines were installed in the spring of 2007. The total installed capacity of the KEA wind power project is 1.16 MW with a total of 17 turbines rated between 65 kW and 100 kW. The operation of the wind power plant has resulted in a wind penetration on the utility system in excess of 35% during periods of low loads. This document and referenced attachments are presented as the final technical report for the U.S. Department of Energy (DOE) grant agreement DE-FG36-97GO10199. Interim deliverables previously submitted are also referenced within this document and where reasonable to do so, specific sections are incorporated in the report or attached as appendices.

Energy-related inventions program invention 637. Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-31

The final technical report for the Pegasus plow, a stalk and root embedding apparatus, describes progress from the development stage to the product support stage. The US Department of Agriculture - Agriculture Research Service (ARS) is now in the second year of a three year study comparing the Pegasus to conventional tillage. So far, no downside has been with the Pegasus and the following benefits have been documented: (1) Energy savings of 65.0 kilowatt hours per hectare over conventional tillage. This is when the Pegasus plow is used to bury whole stalks, and represents a 70% savings over conventional tillage (92.5 kilowatt hours per hectare). (2) Four to seven fewer passes of tillage, depending on the particular situation. This represents a substantial time savings to farmers. (3) So far, no differences in cotton yields. Recent cotton boll counts in one study indicate a higher yield potential with the Pegasus. (4) No disease problems. (5) Significantly higher levels of organic matter in the soil. A hypothesis of the study is that whole stalk burial may reduce plant disease problems. This hypothesis has not yet been proven. (6) Significantly higher levels of nitrate nitrogen. Total nitrogen and ammonia nitrogen trended higher but were not significantly different. This shows that whole stalk burial does not adversely affect the nitrogen cycle in the soil and may actually improve it. The marketing support stage of the project is also described in the report.

Technical Guidelines for Environmental Dredging of Contaminated Sediments

Science.gov (United States)

2008-09-01

material from barges to adjacent rehandling facilities or to move material relatively short distances. Conveyors can also be used to transfer ...by direct dumping or unloading into a chute or conveyor . Truck transport of treated material to landfills may also be considered. The material...environmental dredging for purposes of a feasibility study, remedial design , and implementation. The scope of this document is limited to the technical

Final hazard classification for N basin water filtration and sediment relocation operations

International Nuclear Information System (INIS)

Pisarcik, D.J.; Kretzschmar, S.P.

1996-02-01

This document provides an auditable safety analysis and hazard classification for the filtration of basin water and the relocation of 105-N basin solids to the North Cask Pit within the basin complex. This report assesses the operation of the Water Filtration System and the Remotely Operated Sediment Extraction Equipment (ROSEE). These activities have an activity hazard classification of radiological. Inventories of potentially releasable nonradioactive hazardous materials are far below the reportable quantities of 40 CFR 302. No controls are required to maintain the releasable inventories of these materials below the reportable quantities. Descriptive material is included to provide a general understanding of the water filtration and sediment relocation processes. All equipment will be operated as described in work instructions and/or applicable procedures. Special controls associated with these activities are as follows: (1) A leak inspection of the ROSEE system shall be performed at least once every 5-hour period of sediment relocation operation. (2) A berm must be in place around the North Cask Pit to redirect a potential abovewater ROSEE system leak back to the basin

Technical considerations associated with spent fuel acceptance. Final report

International Nuclear Information System (INIS)

Supko, E.M.

1996-06-01

This study was initiated by the Electric Power Research Institute (EPRI) to identify technical considerations associated with spent fuel acceptance and implementation of a waste management system that includes the use of transportable storage systems, and to serve as an opening dialogue among Standard Contract Holders and the department of Energy's Office of Civilian Radioactive Waste management (OCRWM) prior to the development of waste acceptance criteria or issuance of a Notice of Proposed Rulemaking by OCRWM to amend the Standard Contract. The original purpose of the Notice of Proposed Rulemaking was to address changes to the Standard Contract to implement a multi-purpose canister based system and to address other issues that were not adequately addressed in the standard contract. Even if DOE does not develop a multi-purpose canister based system for waste acceptance, it will still be necessary to develop waste acceptance criteria in order to accept spent fuel in transportable storage systems that are being deployed for at-reactor storage. In this study, technical issues associated with spent fuel acceptance will be defined and potential options and alternatives for resolution of technical considerations will be explored

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Held, Isaac [Princeton Univ., NJ (United States); Balaji, V. [Princeton Univ., NJ (United States); Fueglistaler, Stephan [Princeton Univ., NJ (United States)

2016-09-19

We have constructed and analyzed a series of idealized models of tropical convection interacting with large-scale circulations, with 25-50km resolution and with 1-2km cloud resolving resolution to set the stage for rigorous tests of convection closure schemes in high resolution global climate models. Much of the focus has been on the climatology of tropical cyclogenesis in rotating systems and the related problem of the spontaneous aggregation of convection in non-rotating systems. The PI (Held) will be delivering the honorary Bjerknes lecture at the Fall 2016 AGU meeting in December on this work. We have also provided new analyses of long-standing issues related to the interaction between convection and the large-scale circulation: Kelvin waves in the upper troposphere and lower stratosphere, water vapor transport into the stratosphere, and upper tropospheric temperature trends. The results of these analyses help to improve our understanding of processes, and provide tests for future high resolution global modeling. Our final goal of testing new convections schemes in next-generation global atmospheric models at GFDL has been left for future work due to the complexity of the idealized model results meant as tests for these models uncovered in this work and to computational resource limitations. 11 papers have been published with support from this grant, 2 are in review, and another major summary paper is in preparation.

Interaction of fine sediment with alluvial streambeds

Science.gov (United States)

Jobson, Harvey E.; Carey, William P.

1989-01-01

More knowledge is needed about the physical processes that control the transport of fine sediment moving over an alluvial bed. The knowledge is needed to design rational sampling and monitoring programs that assess the transport and fate of toxic substances in surface waters because the toxics are often associated with silt- and clay-sized particles. This technical note reviews some of the past research in areas that may contribute to an increased understanding of the processes involved. An alluvial streambed can have a large capacity to store fine sediments that are extracted from the flow when instream concentrations are high and it can gradually release fine sediment to the flow when the instream concentrations are low. Several types of storage mechanisms are available depending on the relative size distribution of the suspended load and bed material, as well as the flow hydraulics. Alluvial flow tends to segregate the deposited material according to size and density. Some of the storage locations are temporary, but some can store the fine sediment for very long periods of time.

Sediment movement along the U.S. east coast continental shelf—II. Modelling suspended sediment concentration and transport rate during storms

Science.gov (United States)

Lyne, Vincent D.; Butman, Bradford; Grant, William D.

1990-05-01

Long-term near-bottom wave and current observations and a one-dimensional sediment transport model are used to calculate the concentration and transport of sediment during winter storms at 60-80 m water depth along the southern flank of Georges Bank and in the Mid-Atlantic Bight. Calculations are presented for five stations, separated by more than 600 km alongshelf, that have different bottom sediment texture, bedforms and current conditions. A modified version of the sediment transport model presented by GRANT and GLENN (1983, Technical Report to the American Gas Association), GLENN (1983, D.Sc. Thesis, M.I.T.), and GLENN and GRANT (1987, Journal of Geophysical Research, 92, 8244-8264) is used to examine the influence of wave-current interaction, sediment stratification, and limitations on the erodibility of the bottom sediments on the concentration of sediment in the water column and on transport. Predicted suspended sediment concentrations are higher than observed, based on beam transmissometer measurements, unless an erosion limit of order a few millimeters for sediments finer than 94 μm is imposed. The agreement between predicted and measured beam attenuation is better at stations that have significant amounts of silt plus clay in the surficial sediments than for stations with sandy sediments. Sediment concentrations during storms estimated by MOODYet al. (1987, Continental Shelf Research, 7, 609-628) are within 50% of the model predictions. Sediment transport rates for sediments 94 μm and finer are determined largely by the concentrations in the surficial sediment and the erosion depth limit. Large alongshelf transports in the direction of storm-driven currents are inferred for stations in the Mid-Atlantic Bight. During a 115-day period in winter 1979-1980, the net transport of sediment along the shelf was westward; benthic storms (defined as periods when the bottom wave stress exceeded the current stress by 2 dyn cm -2) occurred between 23 and 73% of the

Final technical report; Mercury Release from Organic matter (OM) and OM-Coated Mineral Surfaces

Energy Technology Data Exchange (ETDEWEB)

Aiken, George

2014-10-02

This document is the final technical report for a project designed to address fundamental processes controlling the release of mercury from flood plain soils associated with East Fork Poplar Creek, Tennessee near the U.S. Department of Energy Oak Ridge facility. The report summarizes the activities, findings, presentations, and publications resulting from an award to the U.S. Geological that were part of a larger overall effort including Kathy Nagy (University of Illinois, Chicago, Ill) and Joseph Ryan (University of Colorado, Boulder, CO). The specific charge for the U.S.G.S. portion of the study was to provide analytical support for the larger group effort (Nagy and Ryan), especially with regard to analyses of Hg and dissolved organic matter, and to provide information about the release of mercury from the floodplain soils.

Sediment yield and alternatives soil conservation practices of teak catchments

Directory of Open Access Journals (Sweden)

Tyas Mutiara Basuki

2017-10-01

Full Text Available Quantifying sediment is essential to determine its sources and reduce its negative impacts. A study was conducted to quantify suspended sediments of catchments covering by teak plantation and to provide alternatives soil conservation practices. Five catchments with old teak coverages of 82; 82; 74; 70; and 53 % were chosen. At the outlet of each catchment was installed tide gauge to monitor stream water level (SWL. Water samples for sediment analyses were taken for every increament of SWL. Sediment yield was calculated based on rating curves of sediment discharge. The results showed that the sources of sediment in the streams were dryland agricultural and streambank erosion. The mean annual sediment yield during the study were 9.3; 10; 15; 53.3; and 22.5 t/ha for catchments covered by old teak plantation of 82, 82, 74, 70, and 53 %, respectively. To reduce sediment yield some soil conservation practices must be applied. Conservation of soil organic matter is important in order to stabilize soil aggregate and prevent clay dispersion which causes erosion and sedimentation. Green firebreaks or making channels are needed to prevent fire during dry season and organic matter loss. Stabilization of streambank is neccesary, either using vegetative method or civil technics.

Reductive immobilization of U(VI) in Fe(III) oxide-reducing subsurface sediments: Analysis of coupled microbial-geochemical processes in experimental reactive transport systems. Final Scientific/Technical Report-EMSP 73914

International Nuclear Information System (INIS)

Eric E. Roden Matilde M. Urrutia Mark O. Barnett Clifford R. Lange

2005-01-01

(VI) reduction is likely to be less efficient in natural soils and sediments than would be inferred from studies with synthetic Fe(III) oxides. A key implication of these findings is that production of Fe(II)-enriched sediments during one-time (or periodic) stimulation of DMRB activity is not likely to permit efficient long-term abiotic conversion of U(VI) to U(IV) in biogenic redox barriers designed to prevent far-field subsurface U(VI) migration. Instead our results suggest that ongoing DMRB activity will be required to achieve maximal U(VI) reduction efficiency, and emphasize the need for detailed understanding of patterns of DMRB growth, colonization, and maintenance in physically and chemically heterogeneous subsurface environments in order to predict the effectiveness of subsurface U(VI) bioremediation operations. A final ''capstone'' aspect of experimental work on the project was to examine the potential for sustained coupled Fe(III) oxide and U(VI) reduction in experimental flow-through reactor systems (i.e. sediment columns and ''semicontinuous culture'' systems) that are conceptually analogous to hydrologically-open subsurface environments. The results conclusively demonstrated the potential for sustained removal of U(VI) from solution via DMRB activity in excess of the U(VI) sorption capacity of the natural mineral assemblages as determined in abiotic controls. In addition, the abundance of sorbed U(VI) (a potential long-term source of U(VI) to the aqueous phase) was much lower in the biotic vs. abiotic systems. The latter results agree with other project findings which demonstrated the capacity for G. sulfurreducens to reduce sorbed U(VI). Throughout the project we have developed and refined a variety of reaction-based models of coupled Fe(III) oxide/U(VI) reduction, including a generalized model which accounts for the population dynamics of various respiratory microbial functional groups. These models have been employed in numerical simulations of both batch bench

Use of waste cellophane in the control of sediment : Final report.

Science.gov (United States)

1978-01-01

Based on laboratory flume tests, it was concluded that waste cellophane could be used effectively for trapping and filtering waterborne sediment. It was also priced competitively and, like straw and burlap, it was found to be biodegradable in a soil ...

The oceanic sediment barrier

International Nuclear Information System (INIS)

Francis, T.J.G.; Searle, R.C.; Wilson, T.R.S.

1986-01-01

Burial within the sediments of the deep ocean floor is one of the options that have been proposed for the disposal of high-level radioactive waste. An international research programme is in progress to determine whether oceanic sediments have the requisite properties for this purpose. After summarizing the salient features of this programme, the paper focuses on the Great Meteor East study area in the Northeast Atlantic, where most oceanographic effort has been concentrated. The geological geochemical and geotechnical properties of the sediments in the area are discussed. Measurements designed to determine the rate of pore water movement through the sediment column are described. Our understanding of the chemistry of both the solid and pore-water phases of the sediment are outlined, emphasizing the control that redox conditions have on the mobility of, for example, naturally occurring manganese and uranium. The burial of instrumented free-fall penetrators to depths of 30 m beneath the ocean floor is described, modelling one of the methods by which waste might be emplaced. Finally, the nature of this oceanic environment is compared with geological environments on land and attention is drawn to the gaps in our knowledge that must be filled before oceanic burial can be regarded as an acceptable disposal option. (author)

The sequence of sediment behaviour during wave-induced liquefaction

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Hatipoglu, Figen; Fredsøe, Jørgen

2006-01-01

to be in agreement with recent centrifuge wave-tank experiments. As for the final stage of the sequence of processes (formation of ripples), the ripple steepness (normalized with the angle of repose) for sediment with liquefaction history is found to be the same as that in sediment with no liquefaction history.......This paper presents the results of an experimental investigation of the complete sequence of sediment behaviour beneath progressive waves. The sediment was silty with d(50) = 0.060 mm. Two kinds of measurements were carried out: pore-water pressure measurements (across the sediment depth...... of liquefaction and compaction fronts in the sediment and (iii) the characteristics of the orbital motion of the liquefied sediment including the motion of the interface between the water body and the sediment. The ranges of the various quantities in the tests were: wave height, H = 9-17 cm, wave period, T = 1...

Sorption Characteristics of Sediments in the Upper Mississippi River System Above Lake Pepin

National Research Council Canada - National Science Library

James, W

1999-01-01

This technical note examines equilibrium phosphorus processes and sorption characteristics for sediments collected from the Minnesota River, immediately upstream from its confluence with the Upper Mississippi River (UMR...

Microscopic heavy-ion theory. Final technical report, June 1, 1993 - May 31, 1996

International Nuclear Information System (INIS)

Ernst, D.J.; Oberacker, V.E.; Umar, A.S.

1998-01-01

In this Final Technical Report, the authors summarize the research activities of the three Principal Investigators (Professors Ernst, Oberacker, and Umar) at Vanderbilt University since the last reporting period through the subject award expiration date (Dec. 31, 1996) under contract DE-FG05-87ER40376 with the Department of Energy. The research effort is divided between the following three areas: nuclear structure and astrophysics (microscopic nuclear structure studies and properties of exotic nuclei at HRIBF, supernovae calculations in connection with nuclear astrophysics, and nuclear viscosity studies via muon-induced fission at PSI); pion and kaon interactions with the nucleus at high energies (interaction of pions and kaons with nuclei from low energies to 1 GeV, propagation of excited hadrons in the nuclear medium as probed by pion and electron induced reactions); nuclear physics at high energies (dynamical string-parton model to study multi-particle production at RHIC, electromagnetic lepton pair production at RHIC)

Development, evaluation, and application of sediment quality targets for assessing and managing contaminated sediments in Tampa Bay, Florida

Science.gov (United States)

MacDonald, D.D.; Carr, R.S.; Eckenrod, D.; Greening, H.; Grabe, S.; Ingersoll, C.G.; Janicki, S.; Janicki, T.; Lindskoog, R.A.; Long, E.R.; Pribble, R.; Sloane, G.; Smorong, D.E.

2004-01-01

Tampa Bay is a large, urban estuary that is located in west central Florida. Although water quality conditions represent an important concern in this estuary, information from numerous sources indicates that sediment contamination also has the potential to adversely affect aquatic organisms, aquatic-dependent wildlife, and human health. As such, protecting relatively uncontaminated areas of the bay from contamination and reducing the amount of toxic chemicals in contaminated sediments have been identified as high-priority sediment management objectives for Tampa Bay. To address concerns related to sediment contamination in the bay, an ecosystem-based framework for assessing and managing sediment quality conditions was developed that included identification of sediment quality issues and concerns, development of ecosystem goals and objectives, selection of ecosystem health indicators, establishment of metrics and targets for key indicators, and incorporation of key indicators, metrics, and targets into watershed management plans and decision-making processes. This paper describes the process that was used to select and evaluate numerical sediment quality targets (SQTs) for assessing and managing contaminated sediments. These SQTs included measures of sediment chemistry, whole-sediment and pore-water toxicity, and benthic invertebrate community structure. In addition, the paper describes how the SQTs were used to develop site-specific concentration-response models that describe how the frequency of adverse biological effects changes with increasing concentrations of chemicals of potential concern. Finally, a key application of the SQTs for defining sediment management areas is discussed.

Head Start Impact Study. Technical Report

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

Dredged sediments as a resource for brick production: Possibilities and barriers from a consumers’ perspective

International Nuclear Information System (INIS)

Cappuyns, Valérie; Deweirt, Valentine; Rousseau, Sandra

2015-01-01

Highlights: • Consumers are suspicious towards bricks produced from dredged sediments. • Technical quality, safety and environmental impacts are considered key characteristics. • Public has insufficient knowledge on bricks produced from dredged sediments. • Sensitization and provision of information to customers are of primary importance. - Abstract: A possible solution for the oversupply of dredged sediments is their use as a raw material in brick production. Despite the fact that several examples (e.g., Agostini et al., 2007; Hamer and Karius, 2002; Xu et al., 2014) show that this application is feasible, some economic, technical and social limitations interfere with the development of a market of dredged materials in brick production in Flanders. While we describe the main characteristics of the supply side, we focus on the limitations and barriers from the demand side in the present study. Based on a consumers survey we analyze consumers’ risk perceptions and attitudes towards bricks produced from dredged sediments. Consumers in Flanders are rather suspicious with respect to bricks produced from dredged sediments and their risk perception is mainly determined by the possibility of a bad bargain (brick of inferior quality) and the connotation with chemical contamination. The willingness to pay for bricks made from dredged sediments is mainly influenced by the age of the respondents, as well environmental awareness, and the respondents’ belief in their ability to influence environmental problems. Sensitization and information of customers seems to be of primary importance to make dredged-sediment-derived bricks a successful product

Dredged sediments as a resource for brick production: Possibilities and barriers from a consumers’ perspective

Energy Technology Data Exchange (ETDEWEB)

Cappuyns, Valérie, E-mail: valerie.cappuyns@kuleuven.be; Deweirt, Valentine; Rousseau, Sandra

2015-04-15

Highlights: • Consumers are suspicious towards bricks produced from dredged sediments. • Technical quality, safety and environmental impacts are considered key characteristics. • Public has insufficient knowledge on bricks produced from dredged sediments. • Sensitization and provision of information to customers are of primary importance. - Abstract: A possible solution for the oversupply of dredged sediments is their use as a raw material in brick production. Despite the fact that several examples (e.g., Agostini et al., 2007; Hamer and Karius, 2002; Xu et al., 2014) show that this application is feasible, some economic, technical and social limitations interfere with the development of a market of dredged materials in brick production in Flanders. While we describe the main characteristics of the supply side, we focus on the limitations and barriers from the demand side in the present study. Based on a consumers survey we analyze consumers’ risk perceptions and attitudes towards bricks produced from dredged sediments. Consumers in Flanders are rather suspicious with respect to bricks produced from dredged sediments and their risk perception is mainly determined by the possibility of a bad bargain (brick of inferior quality) and the connotation with chemical contamination. The willingness to pay for bricks made from dredged sediments is mainly influenced by the age of the respondents, as well environmental awareness, and the respondents’ belief in their ability to influence environmental problems. Sensitization and information of customers seems to be of primary importance to make dredged-sediment-derived bricks a successful product.

Bioleaching of heavy metal polluted sediment: influence of sediment properties. Pt. 2

Energy Technology Data Exchange (ETDEWEB)

Loeser, C. [Technische Universitaet Dresden, Institut fuer Lebensmittel- und Bioverfahrenstechnik, Bergstrasse 120, D-01062 Dresden (Germany); Zehnsdorf, A. [UFZ-Umweltforschungszentrum Leipzig-Halle GmbH, Umwelt- und Biotechnologisches Zentrum, Permoserstrasse 15, D-04318 Leipzig (Germany); Hoffmann, P.; Seidel, H. [UFZ-Umweltforschungszentrum Leipzig-Halle GmbH, Department Bioremediation, Permoserstrasse 15, D-04318 Leipzig (Germany)

2006-08-15

period lasted, and the higher the pH and the lower the fraction of the solubilized heavy metals finally was. Since Cu requires stronger acidic conditions for its solubilization, it responded more sensitively to lime addition than Zn, Ni, and Cd. Heavy metal polluted sediment containing large amounts of carbonate may, in principle, also be remediated by bioleaching, but metal solubilization requires excessive amounts of the leaching agent and is thus uneconomical. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Hydrogeochemical and stream sediment reconnaissance (HSSR) program of the National Uranium Resource Evaluation (NURE) 1973-1984. Technical history

International Nuclear Information System (INIS)

1985-01-01

The Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) program of the National Uranium Resource Evaluation (NURE) generated a database of interest to scientists and other professional personnel in the academic, business, industrial, and governmental communities. NURE was a program of the Department of Energy Grand Junction Office (GJO) to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States. The HSSR program provided for the collection of water and sediment samples located on the 1 0 x 2 0 National Topographic Map Series (NTMS) quadrangle grid across the conterminous United States and Alaska and the analysis of these samples for uranium as well as for a number of additional elements. Although the initial purpose of the program was to provide information regarding uranium resources, the information recorded about other elements and general field or site characteristics has made this database potentially valuable for describing the geochemistry of a location and addressing other issues such as water quality. The purpose of this Technical History is to summarize in one report those aspects of the HSSR program that are likely to be important in helping users assess the database and make informed judgements about its application to specific research questions. The history begins with an overview of the NURE Program and its components. Following a general description of the goals, objectives, and key features of the HSSR program, the implementation of the program at each of the four federal laboratories is presented in four separate chapters. These typically cover such topics as sample collection, sample analysis, and data management. 80 refs., 5 figs., 9 tabs

Technical Note: Stability of a Levee Made of Bottom Sediments From a Dam Reservoir

Directory of Open Access Journals (Sweden)

Koś Karolina

2015-02-01

Full Text Available Stability analysis of a levee made of the bottom sediments from Czorsztyn-Niedzica Reservoir is presented in the paper. These sediments were classified as silty sands and, based on the authors' own research, their geotechnical parameters were beneficial, so the possibility of using this material for the hydraulic embankments was considered. Stability and filtration calculations were carried out for a levee that had the same top width - 3 m, slope inclinations 1:2 and different heights: 4, 6 and 8 m. Two methods were used: analytical and numerical. Calculations were carried out without and with a steady and unsteady seepage filtration. Based on the analysis carried out it was stated that the levee made of the bottom sediments is stable even at the height of 8.0 m, although because of the seepage on the downstream side it is recommended to use a drainage at the toe of the slope.

Technical advisory panel for the large acceptance spectrometer: Final report

International Nuclear Information System (INIS)

1989-01-01

The Technical Advisory Panel for the Large Acceptance Spectrometer met on November 17--19, 1988, at CEBAF to perform a second review of the status of this project. The charge to the Panel was ''to provide technical advice to the CEBAF directorate on the design, construction, cost, schedule, and implementation of the Large Acceptance Spectrometer.'' In this written report, an overview of the entire project is given. Specific comments on the major components, data handling and analysis, assembly and installation, and management are presented. The Panel's conclusions are contained in the Executive Summary at the beginning of the report

Monitoring hydrocarbons and trace metals in Beaufort Sea sediments and organisms. Final report

International Nuclear Information System (INIS)

Boehm, P.; LeBlanc, L.; Trefry, J.; Marajh-Whittemore, P.; Brown, J.

1990-01-01

As part of the Minerals Management Service's environmental studies of oil and gas exploration and production activities in the Alaskan Beaufort Sea, a study was conducted in 1989 to monitor the marine environment for inputs of chemicals related to drilling and exploration. The 1989 Beaufort Sea Monitoring Program (BSMP) was designed to monitor sediments and selected benthic organisms for trace metals and hydrocarbons so as to infer any changes that might have resulted from drilling and production activities. A series of 49 stations were sampled during the program. The study area extended from Cape Halkett on the western end of Harrison Bay to Griffin Point, east of Barter Island. The sampling design combined an area-wide approach in which stations were treated as replicates of 8 specific geographic regions, with an activity-specific approach, which focused on the potential establishment of metal or hydrocarbon concentration gradients with distance from the Endicott Production Field in Prudhoe Bay. The analytical program focused on the analysis of the fine-fraction of the sediment for a series of trace metals and elements and the analysis of a suite of saturated and aromatic hydrocarbons in the bulk sediment. The total organic carbon (TOB) content and the grain size distribution in the sediments were determined as well. Benthic bivalve molluscs, representative of several feeding types were collected from those stations for which data previously existed from the 1984-1986 BSMP, and were analyzed for metals and saturated and aromatic hydrocarbons. The benthic amphipods were collected, pooled by station or region, and analyzed as well

System-Cost-Optimized Smart EVSE for Residential Application: Final Technical Report including Manufacturing Plan

Energy Technology Data Exchange (ETDEWEB)

Zhu, Charles [Delta Products, Triangle Park, NC (United States)

2015-05-15

In the 2nd quarter of 2012, a program was formally initiated at Delta Products to develop smart-grid-enabled Electric Vehicle Supply Equipment (EVSE) product for residential use. The project was funded in part by the U.S. Department of Energy (DOE), under award DE-OE0000590. Delta products was the prime contractor to DOE during the three year duration of the project. In addition to Delta Products, several additional supplier-partners were engaged in this research and development (R&D) program, including Detroit Edison DTE, Mercedes Benz Research and Development North America, and kVA. This report summarizes the program and describes the key research outcomes of the program. A technical history of the project activities is provided, which describes the key steps taken in the research and the findings made at successive stages in the multi-stage work. The evolution of an EVSE prototype system is described in detail, culminating in prototypes shipped to Department of Energy Laboratories for final qualification. After the program history is reviewed, the key attributes of the resulting EVSE are described in terms of functionality, performance, and cost. The results clearly demonstrate the ability of this EVSE to meet or exceed DOE's targets for this program, including: construction of a working product-intent prototype of a smart-grid-enabled EVSE, with suitable connectivity to grid management and home-energy management systems, revenue-grade metering, and related technical functions; and cost reduction of 50% or more compared to typical market priced EVSEs at the time of DOE's funding opportunity announcement (FOA), which was released in mid 2011. In addition to meeting all the program goals, the program was completed within the original budget and timeline established at the time of the award. The summary program budget and timeline, comparing plan versus actual values, is provided for reference, along with several supporting explanatory notes. Technical

Granulometric analysis of sediments containing transuranic radionuclides

International Nuclear Information System (INIS)

Smith, R.M.; Additon, M.K.

1980-11-01

A dry sieving technique using a sonic sifter was selected for the granulometric analysis of sediment samples containing radionuclide contamination. A sieve facility was established in the 234-5Z building for this purpose. Fifty-two contaminated sediment samples from the 216-Z-1A crib were sieved in the facility at a rate of two to four samples per day with no major problems. A comparison of particle size and radionuclide concentration indicated that there is no obvious benefit to particle size separation as a means of sediment decontamination, though an economic analysis will have to be conducted before a final decision can be made

Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

International Nuclear Information System (INIS)

1997-03-01

This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff's review of Atlas Corporation's proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs

Reservoir Sedimentation: Impact, Extent, and Mitigation

Science.gov (United States)

Hadley, Richard F.

Storage reservoirs play an important role in water resources development throughout the world. The one problem with reservoirs that is universal is the continual reduction in usable capacity caused by siltation. This book reviews the world picture of erosion and sediment yield, the large variations that exist, and the physical phenomena related to reservoir siltation. The book is in the Technical Paper series of The World Bank (Technical Paper 71) and is not a formal publication. Rather, it is intended to be circulated to encourage discussion and comment and to communicate results quickly. The book is reproduced from typescript, but this does not detract from the value of the contents as a useful text for hydrologrsts, engineers, and soil conservationists in developing countries.

Final Technical Report - SciDAC Cooperative Agreement: Center for Extended Magnetohydrodynamic Modeling/ Transport and Dynamics in Torodial Fusion System

International Nuclear Information System (INIS)

Schanck, Dalton D.

2010-01-01

Final technical report for research performed by Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Extended MHD Modeling, DE-FC02-06ER54870, for the period 7/1/06 to 2/15/08. Principal results for this period are: 1. Development of a model for computational modeling for the primitive form of the extended MMD equations. This was reported as Phys. Plasmas 13, 058103 (2006). 2. Comparison between the NIMROD and M3D codes for simulation of the nonlinear sawtooth crash in the CDXU tokamak. This was reported in Phys. Plasmas 14, 056105 (2006). 3. Demonstration of 2-fluid and gyroviscous stabilization of interchange modes using computational extended MHD models. This was reported in Phys. Rev. Letters 101, 085005 (2008). Each of these publications is attached as an Appendix of this report. They should be consulted for technical details.

Dynamics of river sediments in forested headwater streams: Plynlimon

Directory of Open Access Journals (Sweden)

G. J. L. Leeks

1997-01-01

Full Text Available Long term studies of fluvial sediment processes in the Plynlimon catchments have contributed to the assessment and quantification of plantation forestry impacts in British upland catchments, at all stages of the forest cycle. The results from the Plynlimon studies are placed in the context of the observed impacts of particular forest practices and studies of forestry effects on sediment transport elsewhere in the world. The effects associated with drain excavation, ploughing, track construction, ground and channel disruption are outlined for both bedload and, particularly, for suspended load. Finally, recent data on sediment yields from 1995 to 1997 at Plynlimon are reported and discussed in the light of longer-term sediment yield estimates. This paper also provides background information relevant to other sediment process studies which use data from the main Plynlimon sediment monitoring network.

GPHS-RTGs in support of the Cassini RTG Program. Addendum to the final technical report, May 1--December 31, 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

This Addendum to the Cassini GPHS-RTG Program Final Technical Progress Report describes activities performed during the period 1 May 1998 through 31 December 1998, including effort reflecting contract modification M058. These activities include Earth Gravity Assist (EGA) reentry and related analyses which are detailed in Part A, and effort related to the installation of CAGO equipment within Lockheed Martin`s Building 100 facility in Valley Forge, PA, which is detailed in Part B.

GPHS-RTGs in support of the Cassini RTG Program. Addendum to the final technical report, May 1-December 31, 1998

International Nuclear Information System (INIS)

1998-12-01

This Addendum to the Cassini GPHS-RTG Program Final Technical Progress Report describes activities performed during the period 1 May 1998 through 31 December 1998, including effort reflecting contract modification M058. These activities include Earth Gravity Assist (EGA) reentry and related analyses which are detailed in Part A, and effort related to the installation of CAGO equipment within Lockheed Martin's Building 100 facility in Valley Forge, PA, which is detailed in Part B

In-Situ Survival Mechanisms of U and Tc Reducing Bacteria in Contaminated Sediments. Final Report

International Nuclear Information System (INIS)

Lee Krumholz Jimmy Ballard

2005-01-01

The proposed effort will identify genes and ultimately physiological mechanisms and pathways that are expressed under in situ conditions and are critical to functioning of aquifer dwelling anaerobic bacteria living in contaminated systems. The main objectives are: (1) Determine which Metal-reducer specific genes are important for activities in normal and contaminated subsurface sediment. To achieve these goals, we have generated a library of chromosomal mutants. These are introduced into contaminated sediments, incubated, allowed to grow, and then reisolated. A negative selection process allows us to determine which mutants have been selected against in sediments and thereby identify genes required for survival in subsurface sediments. (2) Delineate the function of these genes through GeneBank and Clusters of Orthologous Groups (COGs) comparisons and analyze other sediment microorganisms to determine if similar genes are present in these populations. After determining the sequence of the genes identified through the previous objectives, we delineate the role of those specific genes in the physiology of G20, MR-1 and perhaps other microorganisms. (3) Determine the loss in function of a select group of mutants. Cells with mutations in known genes with testable functions are assayed for the loss of that function if specific assays are available. Mutants with unknown loss of function and other mutants are run through a series of tests including motility, attachment, and rate of sulfate or iron reduction. These tests allow us to categorize mutants for subsequent more detailed study

Certification of Mass Fractions of Polycyclic Aromatic Hydrocarbons, Organochlorines and Polybrominated Diphenyl Ethers in IAEA-459 Marine Sediment Sample

International Nuclear Information System (INIS)

2017-01-01

This publication describes the production of certified reference material IAEA-459, which is produced following ISO Guides 34:2009 and 35:2006. This certified reference material is a sediment sample with certified mass fractions of polycyclic aromatic hydrocarbons, organochlorines and polybrominated diphenyl ethers. The assigned final values and their associated uncertainties were derived from robust statistics on the results provided by selected laboratories with demonstrated technical and quality competence, following the guidance given in the ISO Guides. The material is used for quality control and assessment of method performance for a number of organic analytes listed in the Stockholm Convention on Persistent Organic Pollutants as well as other pollutants listed as priority substances included in many environment monitoring programmes.

Modular Radioisotope Thermoelectric Generator (RTG) Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

1992-12-31

Section 2.0 of this report summarizes the MOD-RTG reference flight design, and Section 3.0 discusses the Ground Demonstration System design. Multicouple technology development is discussed in Section 4.0, and Section 5.0 lists all published technical papers prepared during the course of the contract.

Final report on a study of coherence in acceptability criteria for the technical aspects of risks associated with potentially hazardous installations

International Nuclear Information System (INIS)

Chicken, J.C.

1988-01-01

This report describes the results of the study that was made, under Contract No ECI-1390-B7221-85D, for the European Atomic Energy Community. The aim of the study was to examine and assess the feasibility of developing coherent and uniform criteria for judging the acceptability of the technical aspects of the risks associated with potentially hazardous installations. The report is arranged in five main parts. First the nature of hazardous installations is considered and this provides the basis for examination of the currently-used technical risk acceptability criteria. Next, the possible forms of criteria are explored and then universally consistent partial and overall technical risk acceptability criteria are proposed. Following this the implications of using the criteria proposed at the design, regulatory and operating levels are examined. Then, by testing the criteria against some real decisions, the practical problems of using the proposed criteria are explored. This leads to consideration of possible alternatives to the proposed criteria. Finally the conclusions that appear to be justified are summarized and the need for further work is identified

Residues, Sources and Potential Biological Risk of Organochlorine Pesticides in Surface Sediments of Qiandao Lake, China.

Science.gov (United States)

Yang, Huayun; Zhou, Shanshan; Li, Weidong; Liu, Qi; Tu, Yunjie

2015-10-01

Sediment samples were analyzed to comprehensively characterize the concentrations, distribution, possible sources and potential biological risk of organochlorine pesticides in Qiandao Lake, China. Concentrations of sumHCH and sumDDT in sediments ranged from 0.03 to 5.75 ng/g dry weight and not detected to 14.39 ng/g dry weight. The predominant β-HCH and the α-HCH/γ-HCH ratios indicated that the residues of HCHs were derived not only from historical technical HCH use but also from additional usage of lindane. Ratios of o,p'-DDT/p,p'-DDT and DDD/DDE suggested that both dicofol-type DDT and technical DDT applications may be present in most study areas. Additionally, based on two sediment quality guidelines, γ-HCH, o,p'-DDT and p,p'-DDT could be the main organochlorine pesticides species of ecotoxicological concern in Qiandao Lake.

A novel approach for assessments of erythrocyte sedimentation rate.

Science.gov (United States)

Pribush, A; Hatskelzon, L; Meyerstein, N

2011-06-01

Previous studies have shown that the dispersed phase of sedimenting blood undergoes dramatic structural changes: Discrete red blood cell (RBC) aggregates formed shortly after a settling tube is filled with blood are combined into a continuous network followed by its collapse via the formation of plasma channels, and finally, the collapsed network is dispersed into individual fragments. Based on this scheme of structural transformation, a novel approach for assessments of erythrocyte sedimentation is suggested. Information about erythrocyte sedimentation is extracted from time records of the blood conductivity measured after a dispersion of RBC network into individual fragments. It was found that the sedimentation velocity of RBC network fragments correlates positively with the intensity of attractive intercellular interactions, whereas no effect of hematocrit (Hct) was observed. Thus, unlike Westergren erythrocyte sedimentation rate, sedimentation data obtained by the proposed method do not require correction for Hct. © 2010 Blackwell Publishing Ltd.

Metal contamination in water sediments; Contaminacion por metales en sedimentos acuaticos

Energy Technology Data Exchange (ETDEWEB)

Usero Garcia, J.; Morillo Aguado, J.; Gracia Manarillo, I. [Universidad de Sevilla. Sevilla (Spain)

1997-09-01

The origin, distribution, and behaviour of metals in aquatic systems, and factors affecting the solubilization and entry into the water column of metals associated with sediments are examined. Also, the interaction of these metals with and toxic effects on living organisms are studied. Finally, the existing methods for assessing the degree of pollution of sediments and the mobility of the metals associated with the sediments are explained. In the second section of this paper, the methods used for sampling, preparing, and analysing the sediments are described. (Author) 48 refs.

Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Howe, Gary [RTI International, Research Triangle Park, NC (United States); Albritton, John [RTI International, Research Triangle Park, NC (United States); Denton, David [RTI International, Research Triangle Park, NC (United States); Turk, Brian [RTI International, Research Triangle Park, NC (United States); Gupta, Raghubir [RTI International, Research Triangle Park, NC (United States)

2018-01-31

technology has great potential to provide clean syngas from coal and petcoke-based gasification at increased efficiency and at significantly lower capital and operating costs than conventional syngas cleanup technologies. However, before the technology can be deemed ready for scale-up to a full commercial-scale demonstration, additional R&D testing is needed at the site to address the following critical technical risks: WDP sorbent stability and performance; Impact of WDP on downstream cleanup and conversion steps; Metallurgy and refractory; Syngas cleanup performance and controllability; Carbon capture performance and additional syngas cleanup The proposed plan to acquire this additional R&D data involves: Operation of the units to achieve an additional 3,000 hours of operation of the system within the performance period, with a target of achieving 1,000 hours of those hours via continuous operation of the entire integrated pre-commercial demonstration system; Rapid turnaround of repairs and/or modifications required as necessary to return any specific unit to operating status with documentation and lessons learned to support technology maturation, and; Proactive performance of maintenance activities during any unplanned outages and if possible while operating.

NetView technical research

Science.gov (United States)

1993-01-01

This is the Final Technical Report for the NetView Technical Research task. This report is prepared in accordance with Contract Data Requirements List (CDRL) item A002. NetView assistance was provided and details are presented under the following headings: NetView Management Systems (NMS) project tasks; WBAFB IBM 3090; WPAFB AMDAHL; WPAFB IBM 3084; Hill AFB; McClellan AFB AMDAHL; McClellan AFB IBM 3090; and Warner-Robins AFB.

Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff`s review of Atlas Corporation`s proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs.

Final priority; technical assistance to improve state data capacity--National Technical Assistance Center to improve state capacity to accurately collect and report IDEA data. Final priority.

Science.gov (United States)

2013-05-20

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State Data Capacity program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2013 and later years. We take this action to focus attention on an identified national need to provide technical assistance (TA) to States to improve their capacity to meet the data collection and reporting requirements of the Individuals with Disabilities Education Act (IDEA). We intend this priority to establish a TA center to improve State capacity to accurately collect and report IDEA data (Data Center).

TBT-contaminated sediments. Treatment in a pilot scale

Energy Technology Data Exchange (ETDEWEB)

Stichnothe, H.; Calmano, W.; Arevalo, E.; Keller, A.; Thoeming, J. [Hamburg Univ. of Technology, Dept. Environmental Science and Technology, Hamburg (Germany)

2005-07-01

Background, aims and scope. Sediments in harbours and nearby shipyards demonstrate widespread contamination with tributyltin (TBT). Therefore, reuse and relocation of dredged material from these locations are prohibited. Even if the international marine organization (IMO) convention concerning TBT-based paints is ratified (champ 2003) the TBT problem in sediments will continue to remain for many years due to the persistence of TBT. Methods. An electrochemical process has been developed to treat polluted sediments. Dredged materials with high and low TBT-contents were studied on a technical and a pilot scale. The treatment process was assessed by chemical analysis and a biotest battery. Additionally, an economic analysis was performed to check the economic feasibility of the process to treat dredged material from two different locations at different operating conditions. Furthermore an up-scaling estimation was performed to evaluate treatment costs at a larger scale, i.e. for a plant having a capacity of 720,000 t/a. Results and discussion. Butyltin species and polycyclic aromatic hydrocarbons (PAH) were decomposed due to electrochemically-induced oxidation, while the treatment did not alter heavy metal and PCB concentrations. The bacteria luminescence test indicated a reduced toxicity after the electrochemical treatment, while the algae growth inhibition test and bacteria contact test did not confirm these results. Based on a small consumer price of Euro 0.12/kWh, treating the high-contaminated sediment in the pilot plant would cost Euro 21/m{sup 3} and Euro 31/m{sup 3} for the low contaminated sediment, respectively. Assuming an industrial consumer price of Euro 0.06/kWh for electricity in an up-scaled process with a capacity of 720,000 t/a, the total treatment costs for the low contaminated sediment would be Euro 13/m{sup 3}. Conclusion. The results of treating dredged material from Bremerhaven and the fine-grained fraction from the METHA plant show that the

Yucca Mountain Climate Technical Support Representative

International Nuclear Information System (INIS)

Sharpe, Saxon E

2007-01-01

The primary objective of Project Activity ORD-FY04-012, 'Yucca Mountain Climate Technical Support Representative', was to provide the Office of Civilian Radioactive Waste Management (OCRWM) with expertise on past, present, and future climate scenarios and to support the technical elements of the Yucca Mountain Project (YMP) climate program. The Climate Technical Support Representative was to explain, defend, and interpret the YMP climate program to the various audiences during Site Recommendation and License Application. This technical support representative was to support DOE management in the preparation and review of documents, and to participate in comment response for the Final Environmental Impact Statement, the Site Recommendation Hearings, the NRC Sufficiency Comments, and other forums as designated by DOE management. Because the activity was terminated 12 months early and experience a 27% reduction in budget, it was not possible to complete all components of the tasks as originally envisioned. Activities not completed include the qualification of climate datasets and the production of a qualified technical report. The following final report is an unqualified summary of the activities that were completed given the reduced time and funding

Systems study 'Alternative Entsorgung'. Final report. Technical annex 6

International Nuclear Information System (INIS)

1984-08-01

In the conditioning plant, fuel elements which have been stored for ten years are loaded into transport containers, unloaded, identified and welded into a dry storage box. The dry store barrel is introduced into a final storage container, which, after being closed, is packed in lost shielding. This so-called final storage barrel is finally placed in a transport container and leaves the conditioning plant in this form by rail for transport to the final storage mine. The fuel element method of treatment 'packing of three complete fuel elements' was used as the reference process. In addition, the method of treatment 'fuel elements dismantled into fuel rods' was also examined. The handling of fuel elements and secondary waste treatment in the reference process are described in detail. (orig./HP) [de

IRIS Final Technical Progress Report

Energy Technology Data Exchange (ETDEWEB)

M. D. Carelli

2003-11-03

OAK-B135 This NERI project, originally started as the Secure Transportable Autonomous Light Water Reactor (STAR-LW) and currently known as the International Reactor Innovative and Secure (IRIS) project, had the objective of investigating a novel type of water-cooled reactor to satisfy the Generation IV goals: fuel cycle sustainability, enhanced reliability and safety, and improved economics. The research objectives over the three-year (1999-2002) program were as follows: First year: Assess various design alternatives and establish main characteristics of a point design; Second year: Perform feasibility and engineering assessment of the selected design solutions; Third year: Complete reactor design and performance evaluation, including cost assessment These objectives were fully attained and actually they served to launch IRIS as a full fledged project for eventual commercial deployment. The program did not terminate in 2002 at the end of the NERI program, and has just entered in its fifth year. This has been made possible by the IRIS project participants which have grown from the original four member, two-countries team to the current twenty members, nine countries consortium. All the consortium members work under their own funding and it is estimated that the value of their in-kind contributions over the life of the project has been of the order of $30M. Currently, approximately 100 people worldwide are involved in the project. A very important constituency of the IRIS project is the academia: 7 universities from four countries are members of the consortium and five more US universities are associated via parallel NERI programs. To date, 97 students have worked or are working on IRIS; 59 IRIS-related graduate theses have been prepared or are in preparation, and 41 of these students have already graduated with M.S. (33) or Ph.D. (8) degrees. This ''final'' report (final only as far as the NERI program is concerned) summarizes the work performed

Cohesive and mixed sediment in the Regional Ocean Modeling System (ROMS v3.6 implemented in the Coupled Ocean–Atmosphere–Wave–Sediment Transport Modeling System (COAWST r1234

Directory of Open Access Journals (Sweden)

C. R. Sherwood

2018-05-01

Full Text Available We describe and demonstrate algorithms for treating cohesive and mixed sediment that have been added to the Regional Ocean Modeling System (ROMS version 3.6, as implemented in the Coupled Ocean–Atmosphere–Wave–Sediment Transport Modeling System (COAWST Subversion repository revision 1234. These include the following: floc dynamics (aggregation and disaggregation in the water column; changes in floc characteristics in the seabed; erosion and deposition of cohesive and mixed (combination of cohesive and non-cohesive sediment; and biodiffusive mixing of bed sediment. These routines supplement existing non-cohesive sediment modules, thereby increasing our ability to model fine-grained and mixed-sediment environments. Additionally, we describe changes to the sediment bed layering scheme that improve the fidelity of the modeled stratigraphic record. Finally, we provide examples of these modules implemented in idealized test cases and a realistic application.

Biodegradation studies of diesel-contaminated soils and sediments

International Nuclear Information System (INIS)

Schlauch, M.; Clark, D.

1992-01-01

Radian Corporation is currently remediating the Atchison, Topeka and Sante Fe Railway Superfund site in Clovis, New Mexico. Biodegradation of the petroleum hydrocarbon-contaminated soils and sediments was chosen as the remedial alternative. In order to evaluate the optimum conditions for full-scale bioremediation at this site, Radian designed and implemented various laboratory and field studies. The initial laboratory treatability study was conducted to determine if hydrocarbons in both soils and sediments could be biodegraded using indigenous microorganisms, and determine that the soil were biodegradable, while the sediments were not due to inhibitory factors. To further evaluate the biodegradability6 of the sediments, a laboratory study was initiated which introduced chloride-resistant microbes. The study showed that the sediment bioremediation was possibly by utilizing these microbes; however, the cost was not favorable. Finally, a field plot study was initiated to determine how soil biodegradation would proceed in field conditions, to optimize influencing factors such as moisture and nutrient levels and bioseed addition, and to investigate alternate methods of bioremediating the sediments. Results showed that hydrocarbons in the soils biodegraded much faster in the field than in the lab, and that hydrocarbons in sediments applied to biotreated soils containing acclimated microorganisms were successfully biodegraded

Technical oversight for installation of TNX piezometers, Final Report

Energy Technology Data Exchange (ETDEWEB)

Pidcoe, W.W. Jr. [Westinghouse Savannah River Company, Aiken, SC (United States)

1997-06-05

Science Applications International Corporation was tasked under subcontract C002025P to provide technical oversight for the drilling of one pilot borehole, and the drilling and installation of five piezometers in the TNX Area Swamp. The work was performed in accordance with the Statement of Work in Task Order Proposal No. ER39-129 dated August 6, 1996. This report describes the activities associated with the performance of the task.

Volatiles combustion in fluidized beds. Final technical report, 4 September 1992--4 June 1995

Energy Technology Data Exchange (ETDEWEB)

Pendergrass, R.A. II; Raffensperger, C.; Hesketh, R.P.

1996-02-29

The goal of this project is to investigate the conditions in which volatiles will burn within both the dense and freeboard regions of fluidized beds. Experiments using a fluidized bed operated at incipient fluidization are being conducted to characterize the effect of particle surface area, initial fuel concentration, and particle type on the inhibition of volatiles within a fluidized bed. A review of the work conducted under this grant is presented in this Final Technical Report. Both experimental and theoretical work have been conducted to examine the inhibition of the combustion by the fluidized bed material, sand. It has been shown that particulate phase at incipient fluidization inhibits the combustion of propane by free radical destruction at the surface of sand particles within the particulate phase. The implications of these findings is that at bed temperatures lower than the critical temperatures, gas combustion can only occur in the bubble phase or at the top surface of a bubbling fluidized bed. In modeling fluidized bed combustion this inhibition by the particulate phase should be included.

Development of the biosphere code BIOMOD: final report

International Nuclear Information System (INIS)

Kane, P.

1983-05-01

Final report to DoE on the development of the biosphere code BIOMOD. The work carried out under the contract is itemised. Reference is made to the six documents issued along with the final report. These consist of two technical notes issued as interim consultative documents, a user's guide and a programmer's guide to BIOMOD, a database description, program test document and a technical note entitled ''BIOMOD - preliminary findings''. (author)

A new marine sediment certified reference material (CRM) for the determination of persistent organic contaminants: IAEA-459.

Science.gov (United States)

Tolosa, Imma; Cassi, Roberto; Huertas, David

2018-04-11

A new marine sediment certified reference material (IAEA 459) with very low concentrations (μg kg -1 ) for a variety of persistent organic contaminants (POPs) listed by the Stockholm Convention, as well as other POPs and priority substances (PSs) listed in many environmental monitoring programs was developed by the IAEA. The sediment material was collected from the Ham River estuary in South Korea, and the assigned final values were derived from robust statistics on the results provided by selected laboratories which demonstrated technical and quality competence, following the guidance given in ISO Guide 35. The robust mean of the laboratory means was assigned as certified values, for those compounds where the assigned value was derived from at least five datasets and its relative expanded uncertainty was less than 40% of the assigned value (most of the values ranging from 8 to 20%). All the datasets were derived from at least two different analytical techniques which have allowed the assignment of certified concentrations for 22 polychlorinated biphenyl (PCB) congeners, 6 organochlorinated (OC) pesticides, 5 polybrominated diphenyl ethers (PBDEs), and 18 polycyclic aromatic hydrocarbon (PAHs). Mass fractions of compounds that did not fulfill the criteria of certification are considered information values, which include 29 PAHs, 11 PCBs, 16 OC pesticides, and 5 PBDEs. The extensive characterization and associated uncertainties at concentration levels close to the marine sediment quality guidelines will make CRM 459 a valuable matrix reference material for use in marine environmental monitoring programs.

A Detector for Combined SPECT/CT. Final Technical Report

International Nuclear Information System (INIS)

Vivek Nagarkar

2006-01-01

The goal of the Phase I research was to demonstrate the feasibility of developing a high performance SPECT/CT detector module based on a combination of microcolumnar CsI(Tl) scintillator coupled to an EMCCD readout. We are very pleased to report that our Phase I research has demonstrated the technical feasibility of our approach with a very high degree of success. Specifically, we were able to implement a back-thinned EMCCD with a fiberoptic window which was successfully used to demonstrate the feasibility of near simultaneous radionuclide/CT using the proposed concept. Although significantly limited in imaging area (24 x 24 mm 2 ) and pixel resolution (512 x 512), this prototype has shown exceptional capabilities such as a single optical photon sensitivity, very low noise, an intrinsic resolution of 64 (micro)m for radionuclide imaging, and a resolution in excess of 10 lp/mm for x-ray imaging. Furthermore, the combination of newly developed, thick, microcolumnar CsI and an EMCCD has shown to be capable of operating in a photon counting mode, and that the position and energy information obtained from these data can be used to improve resolution in radionuclide imaging. Finally, the prototype system has successfully been employed for near simultaneous SPECT/CT imaging using both, 125 I and 99m Tc radioisotopes. The tomographic reconstruction data obtained using a mouse heart phantom and other phantoms clearly demonstrate the feasibility and efficacy of the detector in small animal research. The following were the objectives specified in the Phase I proposal: (1) In consultation with Professor Hasegawa, develop specifications for the Phase I/Phase II prototype detector; (2) Modify current vapor deposition protocols to fabricate ∼2 mm thick microcolumnar CsI(Tl) scintillators with excellent columnar structure, high light yield, and high spatial resolution; (3) Perform detailed characterization of the film morphology, light output, and spatial resolution, and use

Post-disturbance sediment recovery: Implications for watershed resilience

Science.gov (United States)

Rathburn, Sara L.; Shahverdian, Scott M.; Ryan, Sandra E.

2018-03-01

Sediment recovery following disturbances is a measure of the time required to attain pre-disturbance sediment fluxes. Insight into the controls on recovery processes and pathways builds understanding of geomorphic resilience. We assess post-disturbance sediment recovery in three small (1.5-100 km2), largely unaltered watersheds within the northern Colorado Rocky Mountains affected by wildfires, floods, and debris flows. Disturbance regimes span 102 (floods, debris flows) to 103 years (wildfires). For all case studies, event sediment recovery followed a nonlinear pattern: initial high sediment flux during single precipitation events or high annual snowmelt runoff followed by decreasing sediment fluxes over time. Disturbance interactions were evaluated after a high-severity fire within the South Fork Cache la Poudre basin was followed by an extreme flood one year post-fire. This compound disturbance hastened suspended sediment recovery to pre-fire concentrations 3 years after the fire. Wildfires over the last 1900 YBP in the South Fork basin indicate fire recurrence intervals of 600 years. Debris flows within the upper Colorado River basin over the last two centuries have shifted the baseline of sediment recovery caused by anthropogenic activities that increased debris flow frequency. An extreme flood on North St. Vrain Creek with an impounding reservoir resulted in extreme sedimentation that led to a physical state change. We introduce an index of resilience as sediment recovery/disturbance recurrence interval, providing a relative comparison between sites. Sediment recovery and channel form resilience may be inversely related because of high or low physical complexity in streams. We propose management guidelines to enhance geomorphic resilience by promoting natural processes that maintain physical complexity. Finally, sediment connectivity within watersheds is an additional factor to consider when establishing restoration treatment priorities.

Final Technical Report: "Representing Endogenous Technological Change in Climate Policy Models: General Equilibrium Approaches"

Energy Technology Data Exchange (ETDEWEB)

Ian Sue Wing

2006-04-18

The research supported by this award pursued three lines of inquiry: (1) The construction of dynamic general equilibrium models to simulate the accumulation and substitution of knowledge, which has resulted in the preparation and submission of several papers: (a) A submitted pedagogic paper which clarifies the structure and operation of computable general equilibrium (CGE) models (C.2), and a review article in press which develops a taxonomy for understanding the representation of technical change in economic and engineering models for climate policy analysis (B.3). (b) A paper which models knowledge directly as a homogeneous factor, and demonstrates that inter-sectoral reallocation of knowledge is the key margin of adjustment which enables induced technical change to lower the costs of climate policy (C.1). (c) An empirical paper which estimates the contribution of embodied knowledge to aggregate energy intensity in the U.S. (C.3), followed by a companion article which embeds these results within a CGE model to understand the degree to which autonomous energy efficiency improvement (AEEI) is attributable to technical change as opposed to sub-sectoral shifts in industrial composition (C.4) (d) Finally, ongoing theoretical work to characterize the precursors and implications of the response of innovation to emission limits (E.2). (2) Data development and simulation modeling to understand how the characteristics of discrete energy supply technologies determine their succession in response to emission limits when they are embedded within a general equilibrium framework. This work has produced two peer-reviewed articles which are currently in press (B.1 and B.2). (3) Empirical investigation of trade as an avenue for the transmission of technological change to developing countries, and its implications for leakage, which has resulted in an econometric study which is being revised for submission to a journal (E.1). As work commenced on this topic, the U.S. withdrawal

Virginia Solar Pathways Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bond, Katharine; Cosby, Sarah

2018-03-28

This Report provides a technical review of the final results of a funding award to Virginia Electric and Power Company (Dominion Energy Virginia (DEV) or the Company) for a project under the U.S. Department of Energy’s Solar Energy Technologies Office. The three-year project was formally known as the Virginia Solar Pathways Project (VSPP or the Project). The purpose of the VSPP was to develop a collaborative utility-administered solar strategy (Solar Strategy) for DEV’s service territory in the Commonwealth that could serve as a replicable model for other states with similar policy environments. The U.S. Department of Energy (DOE) funding award enabled DEV to take a focused approach to developing the Solar Strategy for its Virginia service territory. The structure and funding from the DOE award also facilitated valuable input from a formal stakeholder team convened to serve as advisors (Advisory Team) to the VSPP and contribute their perspectives and expertise to both the analysis and strategy development aspects of the Project. The development of the Solar Strategy involved three main goals: • Establish a policy and program framework that would integrate existing solar programs with new options appropriate for the Commonwealth’s policy environment and broader economic development objectives; • Promote wider deployment of solar within a low retail electric rate environment; and • Serve as a sustainable, utility-administered solar model that could be replicated in other states with similar policy environments, including, but not limited to, the entire Southeast region. In support of the VSPP goals, the Project Team commissioned four studies to support the Solar Strategy development. Two studies, completed by Navigant Consulting, focused on the integration of solar into the electric grid. The first solar integration study focused on integration of solar into the distribution grid where the utility system directly connects to and serves end-use customers

FOREX trading strategy formation using technical analysis

OpenAIRE

Klimavičius, Domas

2010-01-01

FOREX technical analysis indicators, their characteristics and capabilities are researched in this final master thesis. The main goal of this thesis is to determine if technical analysis indicators can recognise patterns in price movements and if they can predict future price movement. The first part of the thesis presents with FOREX theoretical aspects, its characteristics and participants. In the second part of the thesis FOREX analysis tools are overviewed, focusing on technical analysis. ...

Effects of bioirrigation of non-biting midges (Diptera: Chironomidae) on lake sediment respiration

Science.gov (United States)

Baranov, Viktor; Lewandowski, Jörg; Romeijn, Paul; Singer, Gabriel; Krause, Stefan

2016-06-01

Bioirrigation or the transport of fluids into the sediment matrix due to the activities of organisms such as bloodworms (larvae of Diptera, Chironomidae), has substantial impacts on sediment respiration in lakes. However, previous quantifications of bioirrigation impacts of Chironomidae have been limited by technical challenges such as the difficulty to separate faunal and bacterial respiration. This paper describes a novel method based on the bioreactive tracer resazurin for measuring respiration in-situ in non-sealed systems with constant oxygen supply. Applying this new method in microcosm experiments revealed that bioirrigation enhanced sediment respiration by up to 2.5 times. The new method is yielding lower oxygen consumption than previously reported, as it is only sensitive to aerobic heterotrophous respiration and not to other processes causing oxygen decrease. Hence it decouples the quantification of respiration of animals and inorganic oxygen consumption from microbe respiration in sediment.

Final Technical Report for Year 5 Early Career Research Project "Viscosity and equation of state of hot and dense QCD matter"

Energy Technology Data Exchange (ETDEWEB)

Molnar, Denes [Purdue Univ., West Lafayette, IN (United States)

2016-05-25

The Section below summarizes research activities and achievements during the fifth (last) year of the PI’s Early Career Research Project (ECRP). Unlike the first four years of the project, the last year was not funded under the American Recovery and Reinvestment Act (ARRA). The ECRP advanced two main areas: i) radiative 3 ↔ 2 radiative transport, via development of a new computer code MPC/Grid that solves the Boltzmann transport equation in full 6+1D (3X+3V+time); and ii) application of relativistic hydrodynamics, via development of a self-consistent framework to convert viscous fluids to particles. In Year 5 we finalized thermalization studies with radiative gg ↔ ggg transport (Sec. 1.1.1) and used nonlinear covariant transport to assess the accuracy of fluid-to-particle conversion models (Sec. 1.1.2), calculated observables with self-consistent fluid-to-particle conversion from realistic viscous hydrodynamic evolution (Secs. 1.2.1 and 1.2.2), extended the covariant energy loss formulation to heavy quarks (Sec. 1.4.1) and studied energy loss in small systems (Sec. 1.4.2), and also investigated how much of the elliptic flow could have non-hydrodynamic origin (Sec 1.3). Years 1-4 of the ECRP were ARRA-funded and, therefore, they have their own report document ’Final Technical Report for Years 1-4 of the Early Career Research Project “Viscosity and equation of state of hot and dense QCD matter”’ (same award number DE-SC0004035). The PI’s group was also part of the DOE JET Topical Collaboration, a multi-institution project that overlapped in time significantly with the ECRP. Purdue achievements as part of the JET Top- ical Collaboration are in a separate report “Final Technical Report summarizing Purdue research activities as part of the DOE JET Topical Collaboration” (award DE-SC0004077).

75 FR 33682 - Export Administration Regulations; Technical Amendments

Science.gov (United States)

2010-06-15

...-01] RIN 0694-AE93 Export Administration Regulations; Technical Amendments AGENCY: Bureau of Industry... Bureau of Industry and Security (BIS) makes a technical amendment to the Export Administration... review of final decisions and orders issued in BIS export control administrative enforcement proceedings...

Health care fraud and abuse data collection program: technical revisions to Healthcare Integrity and Protection Data Bank data collection activities. Final rule.

Science.gov (United States)

2004-09-21

The rule finalizes technical changes to the Healthcare Integrity and Protection Data Bank (HIPDB) data collection reporting requirements by clarifying the types of personal numeric identifiers that may be reported to the data bank in connection with adverse actions. The rule clarifies that in lieu of a Social Security Number (SSN), an individual taxpayer identification number (ITIN) may be reported to the data bank when, in those limited situations, an individual does not have an SSN.

A manual to identify sources of fluvial sediment

Science.gov (United States)

Gellis, Allen C.; Fitzpatrick, Faith A.; Schubauer-Berigan, Joseph

2016-01-01

sediment sources early in the design of the sediment budget will help later in deciding which tools are necessary to monitor erosion and/or deposition at these sources. Tools can range from rapid inventories to estimate the sediment budget or quantifying sediment erosion, deposition, and export through more rigorous field monitoring. In either approach, data are gathered and erosion and deposition calculations are determined and compared to the sediment export with a description of the error uncertainty. Findings are presented to local stakeholders and management officials.Sediment fingerprinting is a technique that apportions the sources of fine-grained sediment in a watershed using tracers or fingerprints. Due to different geologic and anthropogenic histories, the chemical and physical properties of sediment in a watershed may vary and often represent a unique signature (or fingerprint) for each source within the watershed. Fluvial sediment samples (the target sediment) are also collected and exhibit a composite of the source properties that can be apportioned through various statistical techniques. Using an unmixing-model and error analysis, the final apportioned sediment is determined.

OU3 sediment dating and sedimentation rates

International Nuclear Information System (INIS)

Blair, R.B.; Wolaver, H.A.; Burger, V.M.

1994-01-01

Environmental Technologies at Rocky Flats Environmental Technology Site (RFS) investigated the sediment history of Standley Lake, Great Western Reservoir, and Mower Reservoir using 137 Cs and 239,240 Pu global fall-out as dating indicators. These Colorado Front Range reservoirs have been the subject of study by various city, state and national agencies due to suspected Department of Energy Rocky Flats Plant impacts. We performed sediment dating as part of the RCRA Facility Investigation/Remedial Investigation Report for Operable Unit 3. A sediment chronology profile assists scientist in determining the year of sedimentation for a particular peak concentration of contaminants. Radioisotope sediment dating for the three reservoirs indicated sedimentation rates of 0.7 to 0.8 in./yr. for Standley Lake (SL), 0.9 in./yr. for Great Western Reservoir (GWR), and 0.3 in./yr. in Mower Reservoir (MR). RFS sediment dating for Operable Unit 3 compared favorably with the Hardy, Livingston, Burke, and Volchok Standley Lake study. This report describes the cesium/plutonium sediment dating method, estimates sedimentation rates for Operable Unit 3 reservoirs, and compares these results to previous investigations

The evaluation of a framework for measuring the non-technical ward round skills of final year nursing students: An observational study.

Science.gov (United States)

Murray, Kara; McKenzie, Karen; Kelleher, Michael

2016-10-01

The importance of non-technical skills (NTS) to patient outcomes is increasingly being recognised, however, there is limited research into how such skills can be taught and evaluated in student nurses in relation toward rounds. This pilot study describes an evaluation of a NTS framework that could potentially be used to measure ward round skills of student nurses. The study used an observational design. Potential key NTS were identified from existing literature and NTS taxonomies. The proposed framework was then used to evaluate whether the identified NTS were evident in a series of ward round simulations that final year general nursing students undertook as part of their training. Finally, the views of a small group of qualified nurse educators, qualified nurses and general nursing students were sought about whether the identified NTS were important and relevant to practice. The proposed NTS framework included seven categories: Communication, Decision Making, Situational Awareness, Teamwork and Task Management, Student Initiative and Responsiveness to Patient. All were rated as important and relevant to practice. The pilot study suggests that the proposed NTS framework could be used as a means of evaluating student nurse competencies in respect of many non-technical skills required for a successful ward round. Further work is required to establish the validity of the framework in educational settings and to determine the extent to which it is of use in a non-simulated ward round setting. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biomarker-Based Analysis for Contaminants in Sediments/Soil: Review of Cell-Based Assays and cDNA Arrays

National Research Council Canada - National Science Library

Inouye, Laura

2000-01-01

This technical note reviews the existing technology for cell-based biomarker assays and cDNA arrays and explores their potential as rapid, sensitive, and low-cost tools for sediment/soil toxicity screening...

High-Efficiency Nitride-Based Solid-State Lighting. Final Technical Progress Report

International Nuclear Information System (INIS)

Paul T. Fini; Shuji Nakamura

2005-01-01

In this final technical progress report we summarize research accomplished during Department of Energy contract DE-FC26-01NT41203, entitled ''High-Efficiency Nitride-Based Solid-State Lighting''. Two teams, from the University of California at Santa Barbara (Principle Investigator: Dr. Shuji Nakamura) and the Lighting Research Center at Rensselaer Polytechnic Institute (led by Dr. N. Narendran), pursued the goals of this contract from thin film growth, characterization, and packaging/luminaire design standpoints. The UCSB team initially pursued the development of blue gallium nitride (GaN)-based vertical-cavity surface-emitting lasers, as well as ultraviolet GaN-based light emitting diodes (LEDs). In Year 2, the emphasis shifted to resonant-cavity light emitting diodes, also known as micro-cavity LEDs when extremely thin device cavities are fabricated. These devices have very directional emission and higher light extraction efficiency than conventional LEDs. Via the optimization of thin-film growth and refinement of device processing, we decreased the total cavity thickness to less than 1 (micro)m, such that micro-cavity effects were clearly observed and a light extraction efficiency of over 10% was reached. We also began the development of photonic crystals for increased light extraction, in particular for so-called ''guided modes'' which would otherwise propagate laterally in the device and be re-absorbed. Finally, we pursued the growth of smooth, high-quality nonpolar a-plane and m-plane GaN films, as well as blue light emitting diodes on these novel films. Initial nonpolar LEDs showed the expected behavior of negligible peak wavelength shift with increasing drive current. M-plane LEDs in particular show promise, as unpackaged devices had unsaturated optical output power of ∼ 3 mW at 200 mA drive current. The LRC's tasks were aimed at developing the subcomponents necessary for packaging UCSB's light emitting diodes, and packaging them to produce a white light

Sediment Curve Uncertainty Estimation Using GLUE and Bootstrap Methods

Directory of Open Access Journals (Sweden)

aboalhasan fathabadi

2017-02-01

Full Text Available Introduction: In order to implement watershed practices to decrease soil erosion effects it needs to estimate output sediment of watershed. Sediment rating curve is used as the most conventional tool to estimate sediment. Regarding to sampling errors and short data, there are some uncertainties in estimating sediment using sediment curve. In this research, bootstrap and the Generalized Likelihood Uncertainty Estimation (GLUE resampling techniques were used to calculate suspended sediment loads by using sediment rating curves. Materials and Methods: The total drainage area of the Sefidrood watershed is about 560000 km2. In this study uncertainty in suspended sediment rating curves was estimated in four stations including Motorkhane, Miyane Tonel Shomare 7, Stor and Glinak constructed on Ayghdamosh, Ghrangho, GHezelOzan and Shahrod rivers, respectively. Data were randomly divided into a training data set (80 percent and a test set (20 percent by Latin hypercube random sampling.Different suspended sediment rating curves equations were fitted to log-transformed values of sediment concentration and discharge and the best fit models were selected based on the lowest root mean square error (RMSE and the highest correlation of coefficient (R2. In the GLUE methodology, different parameter sets were sampled randomly from priori probability distribution. For each station using sampled parameter sets and selected suspended sediment rating curves equation suspended sediment concentration values were estimated several times (100000 to 400000 times. With respect to likelihood function and certain subjective threshold, parameter sets were divided into behavioral and non-behavioral parameter sets. Finally using behavioral parameter sets the 95% confidence intervals for suspended sediment concentration due to parameter uncertainty were estimated. In bootstrap methodology observed suspended sediment and discharge vectors were resampled with replacement B (set to

Ambient water and sediment quality of Galveston Bay: Present status and historical trends. Volume 1. Final report

Energy Technology Data Exchange (ETDEWEB)

Ward, G.H.; Armstrong, N.E.

1992-08-01

For many years, data relating to the quality of water and sediment have been collected in the Galveston Bay system by a variety of organizations and individuals. The purpose of the project was to compile these data, and to perform a quantitative assessment of water and sediment quality of Galveston Bay and its evolution over time. The study focused on the following categories of parameters: temperature, salinity and related parameters, suspended sediments and turbidity, pH, dissolved oxygen, nutrients as measured by nitrogen, phosphorous and organic carbon, organics as measured by oil and grease, volatile solids and biochemical oxygen demand, chlorophyll-a, coliforms, metals (total and dissolved), and trace organics, including pesticides, herbicides, PAH's, PCB's, and priority pollutants.

Polar source analysis : technical memorandum

Science.gov (United States)

2017-09-29

The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

Final Technical Report: Hawaii Energy and Environmental Technologies Initiative 2009 (HEET)

Science.gov (United States)

2016-05-25

the solution viscosity . "J 45 40 ŕ Ŕ ..., 30 >= § 25 ·.c (.) !"’ 20 p >< w 15 10 :L 0 20 --phorbol esters (mg PEl g kernel) -.-bio... viscosity , Fuel, 87 (2008) 92-102. [ 19] Q. Lu, J. Zhang, X. Zhu, Corrosion properties of bio-oil and its emulsions with diesel, Chin. Sci. Bull...a seawater-based enrichment media and 1 gram of silica to increase the porosity of the often clay -like sediments (Holmes et al., 1995; Whittenbury

Vehicle infrastructure integration proof of concept : technical description--vehicle : final report

Science.gov (United States)

2009-05-19

This report provides the technical description of the VII system developed for the Cooperative Agreement VII Program between the USDOT and the VII Consortium. The basic architectural elements are summarized and detailed descriptions of the hardware a...

Final Scientific and Technical Report State and Regional Biomass Partnerships

Energy Technology Data Exchange (ETDEWEB)

Handley, Rick; Stubbs, Anne D.

2008-12-29

The Northeast Regional Biomass Program successfully employed a three pronged approach to build the regional capacity, networks, and reliable information needed to advance biomass and bioenergy technologies and markets. The approach included support for state-based, multi-agency biomass working groups; direct technical assistance to states and private developers; and extensive networking and partnership-building activities to share objective information and best practices.

Sediment budget in the Lagoon of Venice, Italy

OpenAIRE

Sarretta, Alessandro; Pillon, Simone; Molinaroli, Emanuela; Guerzoni, Stefano; Fontolan, Giorgio

2009-01-01

This is the accepted manuscript of the paper "Sediment budget in the Lagoon of Venice, Italy", published ad final paper in "Continental Shelf Research Volume 30, Issue 8, 15 May 2010, Pages 934-9499" (https://doi.org/10.1016/j.csr.2009.07.002)

NUSC Technical Publications Guide.

Science.gov (United States)

1985-05-01

Facility personnel especially that of A. Castelluzzo, E. Deland, J. Gesel , and E. Szlosek (all of Code 4343). Reviewed and Approved: 14 July 1980 D...their technical content and format. Review and approve the manual outline, the review manuscript, and the final camera - reproducible copy. Conduct in

Sedimentation Characteristics of Kaolin and Bentonite in Concentrated Solutions

Directory of Open Access Journals (Sweden)

Abdulah Obut

2005-11-01

Full Text Available The sedimentation characteristics of two clays, namely kaolinite and bentonite, were determinated at high clay (5 % wt/vol and electrolyte (1 N concentrations using various inorganic-organic compounds. It was observed that the settling behaviour of kaolinite (1:1 clay and montmorillonite (2:1 clay is quite different due to the structural differences between these minerals. Although, similar initial settling rates and final sediment volumes were obtained after 24 hours of settling time for kaolin suspensions, the corresponding rates and volumes for bentonite suspensions varied greatly with the used chemical compound. According to the experimental results, a further intensive theoretical and experimental investigation is needed to reveal the mechanism underlying the sedimentation characteristics of clay minerals at high clay and electrolyte concentrations.

Modeling the Impacts of Suspended Sediment Concentration and Current Velocity on Submersed Vegetation in an Illinois River Pool, USA

National Research Council Canada - National Science Library

Best, Elly

2004-01-01

This technical note uses a modeling approach to examine the impacts of suspended sediment concentrations and current velocity on the persistence of submersed macrophytes in a shallow aquatic system...

Medium energy measurements of N-N parameters. Final technical report, April 1, 1994--September 30, 1996

International Nuclear Information System (INIS)

Ambrose, D.; Betts, W.; Coffey, P.; Glass, G.; McDonough, J.; Riley, P.; Tang, J.L.

1998-08-01

This document is a final technical report describing the accomplishments of the medium/high energy nuclear physics research program at the University of Texas at Austin. The research program had four main thrusts, only one of which can be considered as measurements of N-N parameters: (1) finishing the data analyses associated with recent LAMPF and TRIUMPF N-N experiments, whose overall purpose has been the determination of the nucleon-nucleon amplitudes, both for isospin 0 and 1 at medium energies; (2) continuing work on BNL E871, a search for rare decay modes of the K L ; (3) work on the RHIC-STAR project, an experiment to create and study a quark gluon plasma and nuclear matter at high energy density; (4) beginning a new AGS experiment (E896) which will search for the lowest mass state of the predicted strange di-baryons, the Ho, and other exotic states of nuclear matter through nucleus-nucleus collisions

Zebra Mussel Research Technical Notes. Impacts of Zebra Mussel Infestations on Water Quality. Section 1 - Environmental Testing

National Research Council Canada - National Science Library

Ashby, Steven

1998-01-01

..., and sediment quality. The purpose of this technical note describes potential changes in water quality as a result of zebra mussel infestations in aquatic systems, based on a review of the literature...

NTRCI Legacy Engine Research and Development Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Smith-Holbert, Connie [National Transportation Research Center, Inc., Knoxville, TN (United States); Petrolino, Joseph [National Transportation Research Center, Inc., Knoxville, TN (United States); Watkins, Bart [Power Source Technologies Inc., Corvallis, OR (United States); Irick, David [Power Source Technologies Inc., Corvallis, OR (United States)

2011-12-31

The Legacy engine is a completely new design, transitional diesel engine, replacing the reciprocating engine with a rotary engine. The Legacy engine offers significant advances over conventional internal combustion engines in 1) power to weight ratio; 2) multiple fuel acceptance; 3) fuel economy; and 4) environmental compliance. These advances are achieved through a combination of innovative design geometry, rotary motion, aspiration simplicity, and manufacturing/part simplicity. The key technical challenge to the Legacy engine's commercialization, and the focus of this project, was the development of a viable roton tip seal. The PST concept for the roton tip seal was developed into a manufacturable design. The design was evaluated using a custom designed and fabricated seal test fixture and further refined. This design was incorporated into the GEN2.5A prototype and tested for achievable compression pressure. The Decision Point at the end of Phase 1 of the project (described below) was to further optimize the existing tip seal design. Enhancements to the tip seal design were incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Compression pressures adequate for compression ignition of diesel fuel were achieved, although not consistently in all combustion volumes. The variation in compression pressures was characterized versus design features. As the roton tip seal performance was improved, results pointed toward inadequate performance of the housing side seals. Enhancement of the housing side seal system was accomplished using a custom designed side seal test fixture. The design enhancements developed with the test fixture were also incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Finally, to simplify the requirements for the roton tip seals and to enhance the introduction and combustion of fuel, a flush-mount fuel injector

Auto consolidated cohesive sediments erosion; Erosion des sediments cohesifs en autoconsolidation

Energy Technology Data Exchange (ETDEWEB)

Ternat, F

2007-02-15

Pollutants and suspended matters of a river can accumulate into the sedimentary column. Once deposited, they are submitted to self-weight consolidation processes, ageing and burying, leading to an increase of their erosion resistance. Pollutant fluxes can be related to sedimentary fluxes, determined by threshold laws. In this work, an erosion threshold model is suggested by introducing a cohesion force into the usual force balance. A model of cohesion is developed on the basis of interactions between argillaceous cohesive particles (clays), particularly the Van der Waals force, whose parameterization is ensured by means of granulometry and porosity. Artificial erosion experiments were performed in a recirculating erosion flume with natural cored sediments where critical shear stress measurements were performed. Other analyses provided granulometry and porosity. The results obtained constitute a good database for the literature. The model is then applied to the experimental conditions and gives good agreement with measurements. An example of the accounting for self-weight consolidation processes is finally suggested, before finishing on a Mohr like diagram dedicated to soft cohesive sediment erosion. (author)

Final Project Report: Release of aged contaminants from weathered sediments: Effects of sorbate speciation on scaling of reactive transport

Energy Technology Data Exchange (ETDEWEB)

Jon Chorover, University of Arizona; Peggy O' €™Day, University of California, Merced; Karl Mueller, Penn State University; Wooyong Um, Pacific Northwest National Laboratory; Carl Steefel, Lawrence Berkeley National Laboratory

2012-10-01

Hanford sediments impacted by hyperalkaline high level radioactive waste have undergone incongruent silicate mineral weathering concurrent with contaminant uptake. In this project, we studied the impact of background pore water (BPW) on strontium, cesium and iodine desorption and transport in Hanford sediments that were experimentally weathered by contact with simulated hyperalkaline tank waste leachate (STWL) solutions. Using those lab-weathered Hanford sediments (HS) and model precipitates formed during nucleation from homogeneous STWL solutions (HN), we (i) provided detailed characterization of reaction products over a matrix of field-relevant gradients in contaminant concentration, PCO2, and reaction time; (ii) improved molecular-scale understanding of how sorbate speciation controls contaminant desorption from weathered sediments upon removal of caustic sources; and (iii) developed a mechanistic, predictive model of meso- to field-scale contaminant reactive transport under these conditions.

Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Brown, R. C.; McCarley, T. M.

2006-05-04

. Platform teams organize faculty and students for cross-disciplinary, systems-oriented research and collaborative learning. To date, nine platforms have been developed, although these will most likely be reorganized into a smaller number of broader topics. In the spring of 2004, BRT faculty initiated a regional partnership and collaborative learning program with colleagues at the University of Minnesota, Kansas State University, and South Dakota State University to develop distance education courses in biorenewable resources and technology. As a fledgling graduate program, the BRT graduate program didn’t have the breadth of resources to offer a large number of courses in biorenewables. Other schools faced a similar problem. The academic consortium as first conceived would allow students from the member schools to enroll in biorenewables courses from any of the participating schools, which would assure the necessary enrollment numbers to offer specialized course work. Since its inception, the collaborative curriculum partnership has expanded to include Louisiana State University and the University of Wisconsin. A second international curriculum development campaign was also initiated in the spring of 2004. In particular, several BRT faculty teamed with colleagues at the University of Arkansas, University of Washington, University of Gent (Belgium), National Polytechnic Institute of Toulouse (France), and Technical University of Graz (Austria) to develop an EU-US exchange program in higher education and vocational education/training (entitled “Renewable Resources and Clean Technology”).

Formation of fine sediment deposit from a flash flood river in the Mediterranean Sea

Science.gov (United States)

Grifoll, Manel; Gracia, Vicenç; Aretxabaleta, Alfredo L.; Guillén, Jorge; Espino, Manuel; Warner, John C.

2014-01-01

We identify the mechanisms controlling fine deposits on the inner-shelf in front of the Besòs River, in the northwestern Mediterranean Sea. This river is characterized by a flash flood regime discharging large amounts of water (more than 20 times the mean water discharge) and sediment in very short periods lasting from hours to few days. Numerical model output was compared with bottom sediment observations and used to characterize the multiple spatial and temporal scales involved in offshore sediment deposit formation. A high-resolution (50 m grid size) coupled hydrodynamic-wave-sediment transport model was applied to the initial stages of the sediment dispersal after a storm-related flood event. After the flood, sediment accumulation was predominantly confined to an area near the coastline as a result of preferential deposition during the final stage of the storm. Subsequent reworking occurred due to wave-induced bottom shear stress that resuspended fine materials, with seaward flow exporting them toward the midshelf. Wave characteristics, sediment availability, and shelf circulation determined the transport after the reworking and the final sediment deposition location. One year simulations of the regional area revealed a prevalent southwestward average flow with increased intensity downstream. The circulation pattern was consistent with the observed fine deposit depocenter being shifted southward from the river mouth. At the southern edge, bathymetry controlled the fine deposition by inducing near-bottom flow convergence enhancing bottom shear stress. According to the short-term and long-term analyses, a seasonal pattern in the fine deposit formation is expected.

Toxicity and biodegradation of PCBs in contaminated sediments

International Nuclear Information System (INIS)

Dercova, K.; Cicmanova, J.; Lovecka, P.; Demnerova, K.; Mackova, M.; Hucko, P.; Kusnir, P.

2006-01-01

PCBs represent a serious ecological problem due to their low degradability, high toxicity, and strong bioaccumulation. Because of many environmental and economical problems, there are efforts to develop bio-remediation technologies for decontamination of the PCB-polluted areas. PCB were used by storage of spent nuclear fuel in nuclear power plants Jaslovske Bohunice. In the locality of the former producer of PCB - Chemko Strazske a. s. - big amount of these substances is still persisting in sediments and soil. The goal of this study was to analyze the contaminated sediments from Strazsky canal and Zemplinska Sirava water reservoir from several points of view. The study of eco-toxicity confirmed that both sediments were toxic for various tested organisms. The genotoxicity test has not proved the mutagenic effect. The subsequent step included microbiological analysis of the contaminated sediments and isolation of pure bacterial cultures capable of degrading PCBs. In order to determine the genetic potential for their biodegradability, the gene bphA1 was identified using PCR technique in their genomes. This gene codes the enzyme biphenyl-dioxygenase, which is responsible for PCB degradation. The final goal was to perform aerobic biodegradation of PCBs in the sediments. The bacteria present in both sediments are able to degrade certain low chlorinated congeners. The issue of biodiversity is still open and has to be studied to reveal the real cooperation between bacteria. (authors)

Factors influencing mercury in freshwater surface sediments of northeastern North America

Science.gov (United States)

Kamman, N.C.; Chalmers, A.; Clair, T.A.; Major, A.; Moore, R.B.; Norton, S.A.; Shanley, J.B.

2005-01-01

We report on an inventory and analysis of sediment mercury (Hg) concentrations from 579 sites across northeastern North America. Sediment Hg concentrations ranged from the limit of detection ca. 0.01-3.7 ??g g -1 (dry weight, d.w.), and the average concentration was 0.19 ??g g-1 (d.w.) Sediment methylmercury concentrations ranged from 0.15 to 21 ng g-1 (d.w.) and the mean concentration was 3.83 ng g -1 (d.w.). Total Hg concentrations (HgT) were greatest in lakes > reservoirs > rivers, although the proportion of Hg as methylmercury showed an inverse pattern. Total Hg was weakly and positively correlated with the sediment organic matter and percent of watershed as forested land, and weakly and negatively correlated with sediment solids content, drainage area, and agricultural land. Sediment methylmercury concentrations were weakly and positively correlated to wetland area, and weakly and negatively correlated to drainage area. Methylmercury, expressed as a percentage of HgT was positively correlated to agricultural land area. For sites with co-located sediment and fish-tissue sampling results, there was no relationship between sediment Hg and fish-tissue Hg. Finally, our data indicate that at least 44% of waters across the region have sediment HgT concentrations in excess of Canadian and United States minimum sediment contaminant guidelines for the protection of aquatic biota. ?? 2005 Springer Science+Business Media, Inc.

Historical trends of organochlorine pesticides (OCPs) recorded in sediments across the Tibetan Plateau.

Science.gov (United States)

Yang, Ruiqiang; Xie, Ting; Yang, Handong; Turner, Simon; Wu, Guangjian

2018-02-01

Sediment cores from four lakes across the Tibetan Plateau were used as natural archives to study the time trends of organochlorine pesticides (OCPs). The total concentrations of dichlorodiphenyltrichloroethane (ΣDDT) and hexachlorocyclohexane isomers (ΣHCH) were in the range of 0.04-1.61 and 0.08-1.88 ng/g based on dry weight (dw), while the input fluxes were in the range of 0.3-236 and 0.7-295 pg/cm 2 /y in the core sediments, respectively. The input fluxes of ΣDDT and ΣHCH generally peaked in sediment layers corresponding to the 1970s-1990s and peaked in top sediment layers. The ratio of α/γ-HCH decreased in the top layer sediments, implying that the contribution of lindane (pure γ-HCH) has been increasing in recent years. In addition, the ratio of o,p'-DDT/p,p'-DDT increased significantly over the last 15-20 years, suggesting that dicofol (characterized by high ratio of o,p'-DDT/p,p'-DDT about 7.0) has recently become a relatively more important source of DDT compared to technical DDT itself. The time trends of OCPs recorded in lake sediments examined the impact on such remote alpine regions by human activities.

Technical assistance for Meharry Medical College Energy Efficiency Project. Final project status and technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-05-08

This report presents the results of a program to provide technical assistance to Meharry Medical College. The purpose of the program is to facilitate Meharry`s effort to finance a campus-wide facility retrofit. The US Department of Energy (USDOE) funded the program through a grant to the Tennessee Department of Economic and Community Development (TECD). The University of Memphis-Technology and Energy Services (UM-TES), under contract to TECD, performed program services. The report has three sections: (1) introduction; (2) project definition, financing, and participants; and (3) opportunities for federal participation.

Fundamental studies of the chemical vapor deposition of diamond. Final technical report, April 1, 1988--December 31, 1994

Energy Technology Data Exchange (ETDEWEB)

Nix, W.D.

1995-05-01

We submit here a final technical report for the research program entitled: Fundamental Studies of the Chemical Vapor Deposition of Diamond, DOE Grant No. DE-FG05-88ER45345-M006. This research program was initiated in 1988 under the direction of the late Professor David A. Stevenson and was renewed in 1992. Unfortunately, at the end of 1992, just as the last phase of this work was getting underway, Professor Stevenson learned that he had developed mesothelioma, a form of cancer based on asbestos. Professor Stevenson died from that disease in February of 1994. Professor William D. Nix, the Chairman of the Materials Science department at Stanford was named the Principal Investigator. Professor Nix has assembled this final technical report. Much of the work of this grant was conducted by Mr. Paul Dennig, a graduate student who will receive his Ph.D. degree from Stanford in a few months. His research findings are described in the chapters of this report and in the papers published over the past few years. The main discovery of this work was that surface topology plays a crucial role in the nucleation of diamond on silicon. Dennig and his collaborators demonstrated this by showing that diamond nucleates preferentially at the tips of asperities on a silicon surface rather than in the re-entrant comers at the base of such asperities. Some of the possible reasons for this effect are described in this report. The published papers listed on the next page of this report also describe this research. Interested persons can obtain copies of these papers from Professor Nix at Stanford. A full account of all of the research results obtained in this work is given in the regular chapters that follow this brief introduction. In addition, interested readers will want to consult Mr. Dennig`s Ph.D. dissertation when it is made available later this year.

A review of sediment quantity issues: examples from the River Ebro and adjacent basins (Northeastern Spain).

Science.gov (United States)

Batalla, Ramon J; Vericat, Damià

2011-04-01

Sediment flows naturally through the drainage network, from source areas to deposition zones. Sedimentary disequilibrium in rivers and coastlines is related to the imbalance within the fluvial system caused mostly by dams, instream mining, and changes in land use. This phenomenon is also responsible for ecological perturbations in rivers and streams. A broad need exists to establish comprehensive management strategies (soft measures) that would go beyond site-specific engineering practices (technical measures) typically taken to solve particular problems. Long-term programs are also required to monitor sediment transport in river basins, in order to assess the magnitude and variability of sediment transfer and potential deficits. This paper shows examples of rivers with important sediment disequilibrium in the Ebro and adjacent basins. These basins, like most in the Iberian Peninsula, experience sediment discontinuity in the catchment-river-coast system. Reservoir siltation is the main quantitative issue. Land use change and especially gravel mining downstream from dams accentuate the process. We also present and discuss recent developments on water and sediment management undertaken to improve the morphosedimentary dynamics of rivers. Copyright © 2010 SETAC.

Minutes of the IFMIF technical meeting

International Nuclear Information System (INIS)

Nakamura, H.; Takeda, M.; Ida, M.; Maebara, S.; Yutani, T.; Sugimoto, M.

2004-03-01

The IFMIF Technical Meeting was held on December 4-5, 2003 at Shiran-kaikan, Kyoto University. The main objectives are 1) to finalize the Comprehensive Design Report (CDR), 2) to discuss IFMIF cost and organization, 3) to review technical status of major systems, transition phase activities and EVEDA plan. This report presents a brief summary of the results of the meeting. Agenda, participants list and presentation materials are attached as Appendix. (author)

Supplementary guidance for the investigation and risk-assessment of potentially contaminated sediments

Energy Technology Data Exchange (ETDEWEB)

Baker, K.; Spadaro, P.; Starr, J.; Thomas, J. [Arcadis, Arnhem (Netherlands); Hildenbrand, B. [Energy Institute, London (United Kingdom); Smith, J.W.N.; Dunk, M.; Grosjean, T.; De Ibarra, M.; Medve, A.; Den Haan, K.

2013-11-15

This report provides guidance on the investigation and assessment of potentially contaminated sediments, focusing on the inland, estuarine and coastal environments. It is designed as a complementary, technical companion document to Energy Institute and CONCAWE (2013) report 'Guidance on characterising, assessing and managing risks associated with potentially contaminated sediments' (Report E1001). It highlights a number of significant challenges associated with assessing the aquatic and water bottom environment, which means that a sediment assessment should not be undertaken lightly. Where a decision is taken to undertake a site assessment, this report promotes the use of an iterative process of Conceptual Site Model (CSM) development, data collection, data evaluation and a continuous CSM refinement, taking into account the results obtained. Risk-based assessment is described throughout the report, entailing four tiers of assessment, which progress from a qualitative assessment (Tier 0) through to a detailed cause-attribution assessment (Tier 3), in which the decrease in uncertainty in the assessment process is balanced against the increased costs and timescales with progress to a higher tier assessment. The application of this evidence-driven risk-based approach to sediment site management, including remedial control measures, should help to overcome at least some of the challenges associated with contaminants in sediment sites in Europe, and promote a sustainable approach to sediment management on a case-by-case basis.

Establishment of the International Power Institute. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Julius E. Coles

2000-08-04

The International Power Institute, in collaboration with American industries, seeks to address technical, political, economic and cultural issues of developing countries in the interest of facilitating profitable transactions in power related infrastructure projects. IPI works with universities, governments and commercial organizations to render project-specific recommendations for private-sector investment considerations. IPI also established the following goals: Facilitate electric power infrastructure transactions between developing countries and the US power industry; Collaborate with developing countries to identify development strategies to achieve energy stability; and Encourage market driven solutions and work collaboratively with other international trade energy, technology and banking organizations.

Uranium (VI) Sorption and Transport in Unsaturated, Subsurface Hanford Site Sediments - Effect of Moisture Content and Sediment Texture: Final Report for Subtask 2b

International Nuclear Information System (INIS)

Gamerdinger, A.P.; Resch, C.T.; Kaplan, D.I.

1998-01-01

A series of experiments were conducted in fiscal year 1998 at the Pacific Northwest National Laboratory as part of the Immobilized Low-Activity Waste-Performance Assessment. These experiments evaluated the sorption and transport of uranium, U(VI), under conditions of partial moisture saturation that are relevant to arid region burial sites and vadose-zone far-field conditions at the Hanford Site. The focus was on measuring breakthrough curves (from which distribution coefficient [K d ] values can be calculated) for U(W) in three Hanford Site sediments that represent different texture classes in two unsaturated moisture conditions. Previous research showed that K d values measured during transport in unsaturated sediments varied with moisture saturation

Modelling the transport of sediments and plutonium from the Mururoa lagoon

International Nuclear Information System (INIS)

Rajar, R.; Zagar, D.

1999-01-01

The paper deals with the three-dimensional simulation of resuspension and transport of sediments from the Mururoa lagoon into the Pacific Ocean. These sediments were contaminated mainly by plutonium during French nuclear tests (from 1966 to 1996). Two cases were simulated: 'Normal conditions', taking into account permanent action of trade winds and tides and 'storm conditions', where the effect of a tropical cyclone with maximum wind velocity of 150 km/h and with a frequency of 1 storm per 10 years is simulated. The final results show, that the normal conditions cause an annual outflow of 8 x 10 4 tons of sediment and 8 GBq of plutonium, while one tropical cyclone would cause outflow of 3.9 x 10 6 tons of sediment and about 0.7 TBq of plutonium. (author)

High tracking resolution detectors. Final Technical Report

International Nuclear Information System (INIS)

Vasile, Stefan; Li, Zheng

2010-01-01

High-resolution tracking detectors based on Active Pixel Sensor (APS) have been valuable tools in Nuclear Physics and High-Energy Physics research, and have contributed to major discoveries. Their integration time, radiation length and readout rate is a limiting factor for the planed luminosity upgrades in nuclear and high-energy physics collider-based experiments. The goal of this program was to demonstrate and develop high-gain, high-resolution tracking detector arrays with faster readout, and shorter radiation length than APS arrays. These arrays may operate as direct charged particle detectors or as readouts of high resolution scintillating fiber arrays. During this program, we developed in CMOS large, high-resolution pixel sensor arrays with integrated readout, and reset at pixel level. Their intrinsic gain, high immunity to surface and moisture damage, will allow operating these detectors with minimal packaging/passivation requirements and will result in radiation length superior to APS. In Phase I, we designed and fabricated arrays with calorimetric output capable of sub-pixel resolution and sub-microsecond readout rate. The technical effort was dedicated to detector and readout structure development, performance verification, as well as to radiation damage and damage annealing.

Expectation and task for constructing the volume reduction system of removed soils. In search of the technical integrity from the intermediate storage to final disposal

International Nuclear Information System (INIS)

Mori, Hisaki

2016-01-01

The intermediate storage volume of the removed soils and incineration ash in Fukushima is supposed about 22 million cubic meters. Within 30 years after starting the intermediate storage, the final disposal outside Fukushima prefecture to these removed soils and incineration ash is determined by the law. Because these removed soils are the very-very low radio activity, the volume reduction method is most effective to reduce the burden of the final disposal. As the volume reduction technology is the stage of research and development, the possibility of the introduction of the volume reduction technology that has the consistency of the final disposal technology is evaluated from the point of view of cost. Since this business is accompanied by economic and technical risk to implement private companies, this project is considered appropriate to be implemented as a national project. (author)

Scalable data management, analysis and visualization (SDAV) Institute. Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Geveci, Berk [Kitware, Inc., Clifton Park, NY (United States)

2017-03-28

The purpose of the SDAV institute is to provide tools and expertise in scientific data management, analysis, and visualization to DOE’s application scientists. Our goal is to actively work with application teams to assist them in achieving breakthrough science, and to provide technical solutions in the data management, analysis, and visualization regimes that are broadly used by the computational science community. Over the last 5 years members of our institute worked directly with application scientists and DOE leadership-class facilities to assist them by applying the best tools and technologies at our disposal. We also enhanced our tools based on input from scientists on their needs. Many of the applications we have been working with are based on connections with scientists established in previous years. However, we contacted additional scientists though our outreach activities, as well as engaging application teams running on leading DOE computing systems. Our approach is to employ an evolutionary development and deployment process: first considering the application of existing tools, followed by the customization necessary for each particular application, and then the deployment in real frameworks and infrastructures. The institute is organized into three areas, each with area leaders, who keep track of progress, engagement of application scientists, and results. The areas are: (1) Data Management, (2) Data Analysis, and (3) Visualization. Kitware has been involved in the Visualization area. This report covers Kitware’s contributions over the last 5 years (February 2012 – February 2017). For details on the work performed by the SDAV institute as a whole, please see the SDAV final report.

Ill-posedness in modeling mixed sediment river morphodynamics

Science.gov (United States)

Chavarrías, Víctor; Stecca, Guglielmo; Blom, Astrid

2018-04-01

In this paper we analyze the Hirano active layer model used in mixed sediment river morphodynamics concerning its ill-posedness. Ill-posedness causes the solution to be unstable to short-wave perturbations. This implies that the solution presents spurious oscillations, the amplitude of which depends on the domain discretization. Ill-posedness not only produces physically unrealistic results but may also cause failure of numerical simulations. By considering a two-fraction sediment mixture we obtain analytical expressions for the mathematical characterization of the model. Using these we show that the ill-posed domain is larger than what was found in previous analyses, not only comprising cases of bed degradation into a substrate finer than the active layer but also in aggradational cases. Furthermore, by analyzing a three-fraction model we observe ill-posedness under conditions of bed degradation into a coarse substrate. We observe that oscillations in the numerical solution of ill-posed simulations grow until the model becomes well-posed, as the spurious mixing of the active layer sediment and substrate sediment acts as a regularization mechanism. Finally we conduct an eigenstructure analysis of a simplified vertically continuous model for mixed sediment for which we show that ill-posedness occurs in a wider range of conditions than the active layer model.

Data quality objectives summary report for 105-N Basin sediment disposition

International Nuclear Information System (INIS)

Pisarcik, D.J.

1996-10-01

During stabilization of the 105-N Basin, sediments that have accumulated on basin surfaces will be vacuumed, collected in the North Cask Pit of the basin complex, and eventually removed. The environmental assessment for the deactivation of the N Reactor Facilities describes two potential disposition paths for the 105-N Basin sediment: transfer in slurry form to a double-shell tank if determined to be a transuranic waste, or disposal in solid form as a low-level waste. Interim storage of the sediments may be required if a transfer to the Tank Waste Remediation System cannot meet scheduled milestones. Selection of a particular alternative depends on the final characterization of the accumulated sediment, regulatory requirements, cost/benefit analyses, and 105-N Stabilization Project schedule requirements. The 105-N Basin Sediment Process is being conducted in two phases. The scope of the first phase includes identification of the sampling requirements, and the specific analyses required to support evaluation of the sediment disposition options. The objectives of the first phase of the 105-N Basin Sediment DQO Process include the following: identify the relevant acceptance criteria for each of the disposition options; and develop a sampling and analysis plan (SAP) sufficiently through to allow evaluation of sediment analysis results against each set of acceptance criteria

Medicare and Medicaid programs; salary equivalency guidelines for physical therapy, respiratory therapy, speech language pathology, and occupational therapy services; revised effective date and technical correction--HCFA. Final rule; delay of effective date and correction.

Science.gov (United States)

1998-03-31

This document delays the effective date of the final rule on salary equivalency guidelines, published in the Federal Register (63 FR 5106) on January 30, 1998, from April 1, 1998 to April 10, 1998. In addition, we are making a technical correction in the preamble to the January 30, 1998 final rule.

Technetium-99m: From nuclear medicine applications to fine sediment transport studies

Directory of Open Access Journals (Sweden)

Bandeira Jefferson V.

2017-12-01

Full Text Available The present work is a contribution to rescue the history of development of the application of 99mTc, widely used in nuclear medicine, to its use as tracer for the study of the transport of fine sediment in suspension, in water environment. It addresses the usefulness of its application in obtaining important parameters in environmental studies, illustrating them with some applications already performed and the results obtained. This kind of study, when associated with information on hydrodynamic parameters, for example, river, tidal, wind and wave currents, are powerful tools for the understanding and quantification of fine sediment transport in suspension. Fine sediment is an important vector in the transportation of heavy metals, organic matter and nutrients in water environment, and the quantitative knowledge of its behaviour is mandatory for studies of environmental impacts. Fine sediment labelled with 99mTc, can also be used to study the effect of human interventions, such as dredging of reservoirs, access channels and harbours, and the dumping of dredged materials in water bodies. Besides that, it can be used to optimize dredging works, evaluating the technical and economic feasibility of dumping sites and their environmental impact. It is a valuable support in the calibration and validation of mathematical models for sediment dynamics.

Ecotoxicological evaluation of industrial port of Venice (Italy) sediment samples after a decontamination treatment.

Science.gov (United States)

Libralato, Giovanni; Losso, Chiara; Arizzi Novelli, Alessandra; Citron, Marta; Della Sala, Stefano; Zanotto, Emanuele; Cepak, Franka; Volpi Ghirardini, Annamaria

2008-12-01

This work assesses the ecotoxicological effects of polluted sediment after a decontamination treatment process using a new sediment washing technique. Sediment samples were collected from four sites in Marghera Port industrial channels (Venice, Italy). Ecotoxicological evaluations were performed with Vibrio fischeri and Crassostrea gigas bioassays. Whole sediment and elutriate were deemed as the most suitable environmental matrices for this study. Toxicity scores developed in the Lagoon of Venice for V. fischeri on whole sediment and for C. gigas on elutriate were considered for the final ranking of samples. Ecotoxicological results showed that the treated sediment samples presented both acute and sub-chronic toxicities, which were mainly attributed to the presence of some remaining chemicals such as metals and polyaromatic hydrocarbons. The acute toxicity ranged from low to medium, while the sub-chronic one from absent to very high, suggesting that treated sediments could not be reused in direct contact with seawater.

Summary of the ITER final design report. July 2001

International Nuclear Information System (INIS)

2001-01-01

This document is a summary of the ITER final design report foreseen during the current, Engineering Design Activities (EDA), phase of the ITER project. The report presents the results of collaborative design and supporting technical work undertaken by the ITER Joint Central team (JCT) and the Home Teams (HT) of the parties to the agreement on co-operation in the Engineering Design Activities for ITER (the ITER EDA Agreement). This report marks the achievement of the full technical scope of activities indicated in the ITER EDA Agreement, with a final design which meets the programmatic objective defined in the Agreement and satisfies detailed scientific, technical and costing objectives set by ITER Council in 1998

New usable technical specifications

International Nuclear Information System (INIS)

Webster, S.A.; Tomasi, L.T.; Bernier, R.A.

1989-01-01

After 2 yr of preparation, 1988 finally saw the nuclear industry writing operator-oriented technical specifications. This effort is a continuation of previous efforts to develop improved and usable standard technical specifications (STSs), and is being conducted by the four nuclear steam supply system vendor owners' groups under the auspices of the Nuclear Management Resources Council. Each participant is currently preparing a set of improved STSs based on a writer's guide that was developed through a combined industry effort. In May of 1987, a Human Factors Improvements to Technical Specifications (HFITS) task group was formed to prepare a writer's guide for improved, industrywide STSs. This task group was composed of two representatives from each owners' group, one with a human factors background and one with some operations background. Two documents were prepared in 6 months, a human factors report laying the groundwork for the considerations to go into technical specifications and a writer's guide for their preparation. This paper reports on the application of this writer's guide to the writing of improved STS

TADS Final Evaluation Report, 1980-81. Appendix S.

Science.gov (United States)

Suarez, Tanya M.; And Others

The document contains the final report of the Technical Assistance Development System (TADS), a program which provided technical assistance (TA) services to 53 Handicapped Children's Early Education Program (HCEEP) demonstration projects and 13 State Implementation Grants (SIGs). The evaluation report is divided into five sections. Section 1…

Final report. Geothermal Energy Program: Information dissemination, public outreach, and technical analysis activities. April 1, 1999 to December 31, 2001. USDOE Grant No. DE-FG01-99-EE35098

Energy Technology Data Exchange (ETDEWEB)

Lund, John W.

2002-03-22

This is the final report of the accomplishments of the geothermal energy program: information dissemination, public outreach, and technical analysis activities by the project team consisting of the Geo-Heat Center, Geothermal Resources Council, Geothermal Education Office, Geothermal Energy Association, and the Washington State University Energy Program.

Fifth technical meeting on quality

International Nuclear Information System (INIS)

Girard, A.

1998-01-01

This article reports on the 5th Technical Meeting on Quality which was held in San Diego on 20-22 October 1997 and which was attended by representatives of the Home and Joint Central Team and of manufacturers currently involved in the Large R and D projects. The meeting made progress towards the finalization of the ITER Quality Manual document for inclusion in the Final Design Report and the definition of the quality necessary for ITER procurement and construction

Final Verification Success Story Using the Triad Approach at the Oak Ridge National Laboratory's Melton Valley Soils and Sediment Project

International Nuclear Information System (INIS)

King, D.A.; Haas, D.A.; Cange, J.B.

2006-01-01

The United States Environmental Protection Agency recently published guidance on the Triad approach, which supports the use of smarter, faster, and better technologies and work strategies during environmental site assessment, characterization, and cleanup. The Melton Valley Soils and Sediment Project (Project) at the Oak Ridge National Laboratory embraced this three-pronged approach to characterize contaminants in soil/sediment across the 1000-acre Melton Valley Watershed. Systematic Project Planning is the first of three prongs in the Triad approach. Management initiated Project activities by identifying key technical personnel, included regulators early in the planning phase, researched technologies, and identified available resources necessary to meet Project objectives. Dynamic Work Strategies is the second prong of the Triad approach. Core Team members, including State and Federal regulators, helped develop a Sampling and Analysis Plan that allowed experienced field managers to make real-time, in-the-field decisions and, thus, to adjust to conditions unanticipated during the planning phase. Real-time Measurement Technologies is the third and last prong of the Triad approach. To expedite decision-making, the Project incorporated multiple in-field technologies, including global positioning system equipment integrated with field screening instrumentation, magnetometers for utility clearance, and an on-site gamma spectrometer (spec) for rapid contaminant speciation and quantification. As a result of a relatively complex but highly efficient program, a Project field staff of eight collected approximately 1900 soil samples for on-site gamma spec analysis (twenty percent were also shipped for off-site analyses), 4.7 million gamma radiation measurements, 1000 systematic beta radiation measurements, and 3600 systematic dose rate measurements between July 1, 2004, and October 31, 2005. The site database previously contained results for less than 500 soil samples dating

Ecotoxicological evaluation of industrial port of Venice (Italy) sediment samples after a decontamination treatment

International Nuclear Information System (INIS)

Libralato, Giovanni; Losso, Chiara; Arizzi Novelli, Alessandra; Citron, Marta; Della Sala, Stefano; Zanotto, Emanuele; Cepak, Franka; Volpi Ghirardini, Annamaria

2008-01-01

This work assesses the ecotoxicological effects of polluted sediment after a decontamination treatment process using a new sediment washing technique. Sediment samples were collected from four sites in Marghera Port industrial channels (Venice, Italy). Ecotoxicological evaluations were performed with Vibrio fischeri and Crassostrea gigas bioassays. Whole sediment and elutriate were deemed as the most suitable environmental matrices for this study. Toxicity scores developed in the Lagoon of Venice for V. fischeri on whole sediment and for C. gigas on elutriate were considered for the final ranking of samples. Ecotoxicological results showed that the treated sediment samples presented both acute and sub-chronic toxicities, which were mainly attributed to the presence of some remaining chemicals such as metals and polyaromatic hydrocarbons. The acute toxicity ranged from low to medium, while the sub-chronic one from absent to very high, suggesting that treated sediments could not be reused in direct contact with seawater. - A sediment washing technique was assessed for port contaminated sediment remediation and reuse, indicating its reduced efficiency and the need for further improvements

Ecotoxicological evaluation of industrial port of Venice (Italy) sediment samples after a decontamination treatment

Energy Technology Data Exchange (ETDEWEB)

Libralato, Giovanni [Environmental Sciences Department, Venice University Ca Foscari, Campo della Celestia 2737/b, I-30122 Venice (Italy)], E-mail: giovanni.libralato@unive.it; Losso, Chiara; Arizzi Novelli, Alessandra [Environmental Sciences Department, Venice University Ca Foscari, Campo della Celestia 2737/b, I-30122 Venice (Italy); Citron, Marta; Della Sala, Stefano; Zanotto, Emanuele [Environmental Department, Venice Port Authority, Zattere 1401, I-30123, Venice (Italy); Cepak, Franka [Institute of Public Health, Vojkovo nabrezje 4a, 6000 Koper (Slovenia); Volpi Ghirardini, Annamaria [Environmental Sciences Department, Venice University Ca Foscari, Campo della Celestia 2737/b, I-30122 Venice (Italy)

2008-12-15

This work assesses the ecotoxicological effects of polluted sediment after a decontamination treatment process using a new sediment washing technique. Sediment samples were collected from four sites in Marghera Port industrial channels (Venice, Italy). Ecotoxicological evaluations were performed with Vibrio fischeri and Crassostrea gigas bioassays. Whole sediment and elutriate were deemed as the most suitable environmental matrices for this study. Toxicity scores developed in the Lagoon of Venice for V. fischeri on whole sediment and for C. gigas on elutriate were considered for the final ranking of samples. Ecotoxicological results showed that the treated sediment samples presented both acute and sub-chronic toxicities, which were mainly attributed to the presence of some remaining chemicals such as metals and polyaromatic hydrocarbons. The acute toxicity ranged from low to medium, while the sub-chronic one from absent to very high, suggesting that treated sediments could not be reused in direct contact with seawater. - A sediment washing technique was assessed for port contaminated sediment remediation and reuse, indicating its reduced efficiency and the need for further improvements.

Functional criteria for emergency response facilities. Technical report (final)

International Nuclear Information System (INIS)

1981-02-01

This report describes the facilities and systems to be used by nuclear power plant licensees to improve responses to emergency situations. The facilities include the Technical Support Center (TSC), Onsite Operational Support Center (OSC), and Nearsite Emergency Operations Facility (EOF), as well as a brief discussion of the emergency response function of the control room. The data systems described are the Safety Parameter Display System (SPDS) and Nuclear Data Link (NDL). Together, these facilities and systems make up the total Emergency Response Facilities (ERFs). Licensees should follow the guidance provided both in this report and in NUREG-0654 (FEMA-REP-1), Revision 1, for design and implementation of the ERFs

Modeling Aeolian Transport of Contaminated Sediments at Los Alamos National Laboratory, Technical Area 54, Area G: Sensitivities to Succession, Disturbance, and Future Climate

Energy Technology Data Exchange (ETDEWEB)

Whicker, Jeffrey J. [Los Alamos National Laboratory; Kirchner, Thomas B. [New Mexico State University; Breshears, David D. [University of Arizona; Field, Jason P. [University of Arizona

2012-03-27

The Technical Area 54 (TA-54) Area G disposal facility is used for the disposal of radioactive waste at Los Alamos National Laboratory (LANL). U.S. Department of Energy (DOE) Order 435.1 (DOE, 2001) requires that radioactive waste be managed in a manner that protects public health and safety and the environment. In compliance with that requirement, DOE field sites must prepare and maintain site-specific radiological performance assessments for facilities that receive waste after September 26, 1988. Sites are also required to conduct composite analyses for facilities that receive waste after this date; these analyses account for the cumulative impacts of all waste that has been (and will be) disposed of at the facilities and other sources of radioactive material that may interact with these facilities. LANL issued Revision 4 of the Area G performance assessment and composite analysis in 2008. In support of those analyses, vertical and horizontal sediment flux data were collected at two analog sites, each with different dominant vegetation characteristics, and used to estimate rates of vertical resuspension and wind erosion for Area G. The results of that investigation indicated that there was no net loss of soil at the disposal site due to wind erosion, and suggested minimal impacts of wind on the long-term performance of the facility. However, that study did not evaluate the potential for contaminant transport caused by the horizontal movement of soil particles over long time frames. Since that time, additional field data have been collected to estimate wind threshold velocities for initiating sediment transport due to saltation and rates of sediment transport once those thresholds are reached. Data such as these have been used in the development of the Vegetation Modified Transport (VMTran) model. This model is designed to estimate patterns and long-term rates of contaminant redistribution caused by winds at the site, taking into account the impacts of plant

Modeling Aeolian Transport of Contaminated Sediments at Los Alamos National Laboratory, Technical Area 54, Area G: Sensitivities to Succession, Disturbance, and Future Climate

International Nuclear Information System (INIS)

Whicker, Jeffrey J.; Kirchner, Thomas B.; Breshears, David D.; Field, Jason P.

2012-01-01

The Technical Area 54 (TA-54) Area G disposal facility is used for the disposal of radioactive waste at Los Alamos National Laboratory (LANL). U.S. Department of Energy (DOE) Order 435.1 (DOE, 2001) requires that radioactive waste be managed in a manner that protects public health and safety and the environment. In compliance with that requirement, DOE field sites must prepare and maintain site-specific radiological performance assessments for facilities that receive waste after September 26, 1988. Sites are also required to conduct composite analyses for facilities that receive waste after this date; these analyses account for the cumulative impacts of all waste that has been (and will be) disposed of at the facilities and other sources of radioactive material that may interact with these facilities. LANL issued Revision 4 of the Area G performance assessment and composite analysis in 2008. In support of those analyses, vertical and horizontal sediment flux data were collected at two analog sites, each with different dominant vegetation characteristics, and used to estimate rates of vertical resuspension and wind erosion for Area G. The results of that investigation indicated that there was no net loss of soil at the disposal site due to wind erosion, and suggested minimal impacts of wind on the long-term performance of the facility. However, that study did not evaluate the potential for contaminant transport caused by the horizontal movement of soil particles over long time frames. Since that time, additional field data have been collected to estimate wind threshold velocities for initiating sediment transport due to saltation and rates of sediment transport once those thresholds are reached. Data such as these have been used in the development of the Vegetation Modified Transport (VMTran) model. This model is designed to estimate patterns and long-term rates of contaminant redistribution caused by winds at the site, taking into account the impacts of plant

Nagra technical report 14-02, geological basics - Dossier II - Sediments and tectonic considerations; SGT Etappe 2: Vorschlag weiter zu untersuchender geologischer Standortgebiete mit zugehörigen Standortarealen für die Oberflächenanlage -- Geologische Grundlagen -- Dossier II -- Sedimentologische und tektonische Verhältnisse

Energy Technology Data Exchange (ETDEWEB)

Madritsch, H.; Deplazes, G.

2014-12-15

This dossier is the second of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It considers the sediments that can be used and discusses tectonic considerations. As an introduction, the geological framework is discussed with the various sediments from the Paleozoic, Mesozoic and Cenozoic periods. The various methods used to investigate the rock, such as drilling and reflection-seismic methods along with the investigation of surface formations are discussed. A detailed discussion of the stratigraphic and sedimentological characteristics of the various formations follows. Geological structures and the tectonics in the proposed areas are discussed, as are the depth and thickness of the structures.

Modeling flow, sediment transport and morphodynamics in rivers

Science.gov (United States)

Nelson, Jonathan M.; McDonald, Richard R.; Shimizu, Yasuyuki; Kimura, Ichiro; Nabi, Mohamed; Asahi, Kazutake

2016-01-01

Predicting the response of natural or man-made channels to imposed supplies of water and sediment is one of the difficult practical problems commonly addressed by fluvial geomorphologists. This problem typically arises in three situations. In the first situation, geomorphologists are attempting to understand why a channel or class of channels has a certain general form; in a sense, this is the central goal of fluvial geomorphology. In the second situation, geomorphologists are trying to understand and explain how and why a specific channel will evolve or has evolved in response to altered or unusual sediment and water supplies to that channel. For example, this would include explaining the short-term response of a channel to an unusually large flood or predicting the response of a channel to long-term changes in flow or sediment supply due to various human activities such as damming or diversions. Finally, geomorphologists may be called upon to design or assess the design of proposed man-made channels that must carry a certain range of flows and sediment loads in a stable or at least quasi-stable manner. In each of these three situations, the problem is really the same: geomorphologists must understand and predict the interaction of the flow field in the channel, the sediment movement in the channel and the geometry of the channel bed and banks. In general, the flow field, the movement of sediment making up the bed and the morphology of the bed are intricately linked; the flow moves the sediment, the bed is altered by erosion and deposition of sediment and the shape of the bed is critically important for predicting the flow. This complex linkage is precisely what makes understanding channel form and process such a difficult and interesting challenge.

Ultrasound assisted mercury extraction from soil and sediment

International Nuclear Information System (INIS)

Collasiol, Andre; Pozebon, Dirce; Maia, Sandra M.

2004-01-01

A method for mercury (Hg) determination in soil, river sediment and marine sediment without sample digestion is investigated. Mercury determination is performed by cold vapour atomic absorption spectrometry (CV-AAS) using a flow injection system. Mercury quantitatively leaches out from the investigated marine sediment into 30% (v/v) HNO 3 assisted by ultrasonic irradiation (during 90-120 s) when sample particles size are ≤120 μm. Similar conditions can be applied for Hg determination in river sediment and soil, excepting the time of sonication which needs to be increased to 180 s and KCl is also added to the extraction medium. The presence of 0.15% (m/v) KCl in addition to 30% (v/v) HNO 3 is seen to be effective for quantitative Hg leaching. The certified samples PACS-2 and MESS-3 (both marine sediment from NRCC), Buffalo River (NIST 8704), Montana Soil (NIST 2710) and the non-certified river sediment sample RS-3 were analysed. The attained results were well within the 95% confidence level of the certificate or close to information value. Samples were analysed using aqueous standard calibration. A characteristic mass of 25 pg, a LOD (3s) of 0.2 μg Hg l -1 and a LOQ (10s) of 0.012 μg Hg g -1 are typically attained. These are based on 800 μl of sample solution and 1.000 g of sample mass in 20 ml. The RSD of 10 consecutive runs of the sample is <5%. The proposed method was finally applied for the determination of Hg in real samples of soil, river sediment and marine sediment. The same samples were also analysed using a digestion method giving similar results

Risk-based decision-making framework for the selection of sediment dredging option.

Science.gov (United States)

Manap, Norpadzlihatun; Voulvoulis, Nikolaos

2014-10-15

The aim of this study was to develop a risk-based decision-making framework for the selection of sediment dredging option. Descriptions using case studies of the newly integrated, holistic and staged framework were followed. The first stage utilized the historical dredging monitoring data and the contamination level in media data into Ecological Risk Assessment phases, which have been altered for benefits in cost, time and simplicity. How Multi-Criteria Decision Analysis (MCDA) can be used to analyze and prioritize dredging areas based on environmental, socio-economic and managerial criteria was described for the next stage. The results from MCDA will be integrated into Ecological Risk Assessment to characterize the degree of contamination in the prioritized areas. The last stage was later described using these findings and analyzed using MCDA, in order to identify the best sediment dredging option, accounting for the economic, environmental and technical aspects of dredging, which is beneficial for dredging and sediment management industries. Copyright © 2014 Elsevier B.V. All rights reserved.

High-throughput characterization of sediment organic matter by pyrolysis-gas chromatography/mass spectrometry and multivariate curve resolution: A promising analytical tool in (paleo)limnology.

Science.gov (United States)

Tolu, Julie; Gerber, Lorenz; Boily, Jean-François; Bindler, Richard

2015-06-23

Molecular-level chemical information about organic matter (OM) in sediments helps to establish the sources of OM and the prevalent degradation/diagenetic processes, both essential for understanding the cycling of carbon (C) and of the elements associated with OM (toxic trace metals and nutrients) in lake ecosystems. Ideally, analytical methods for characterizing OM should allow high sample throughput, consume small amounts of sample and yield relevant chemical information, which are essential for multidisciplinary, high-temporal resolution and/or large spatial scale investigations. We have developed a high-throughput analytical method based on pyrolysis-gas chromatography/mass spectrometry and automated data processing to characterize sedimentary OM in sediments. Our method consumes 200 μg of freeze-dried and ground sediment sample. Pyrolysis was performed at 450°C, which was found to avoid degradation of specific biomarkers (e.g., lignin compounds, fresh carbohydrates/cellulose) compared to 650°C, which is in the range of temperatures commonly applied for environmental samples. The optimization was conducted using the top ten sediment samples of an annually resolved sediment record (containing 16-18% and 1.3-1.9% of total carbon and nitrogen, respectively). Several hundred pyrolytic compound peaks were detected of which over 200 were identified, which represent different classes of organic compounds (i.e., n-alkanes, n-alkenes, 2-ketones, carboxylic acids, carbohydrates, proteins, other N compounds, (methoxy)phenols, (poly)aromatics, chlorophyll and steroids/hopanoids). Technical reproducibility measured as relative standard deviation of the identified peaks in triplicate analyses was 5.5±4.3%, with 90% of the RSD values within 10% and 98% within 15%. Finally, a multivariate calibration model was calculated between the pyrolytic degradation compounds and the sediment depth (i.e., sediment age), which is a function of degradation processes and changes in OM

Numerical Simulation of Flow and Suspended Sediment Transport in the Distributary Channel Networks

Directory of Open Access Journals (Sweden)

Wei Zhang

2014-01-01

Full Text Available Flow and suspended sediment transport in distributary channel networks play an important role in the evolution of deltas and estuaries, as well as the coastal environment. In this study, a 1D flow and suspended sediment transport model is presented to simulate the hydrodynamics and suspended sediment transport in the distributary channel networks. The governing equations for river flow are the Saint-Venant equations and for suspended sediment transport are the nonequilibrium transport equations. The procedure of solving the governing equations is firstly to get the matrix form of the water level and suspended sediment concentration at all connected junctions by utilizing the transformation of the governing equations of the single channel. Secondly, the water level and suspended sediment concentration at all junctions can be obtained by solving these irregular spare matrix equations. Finally, the water level, discharge, and suspended sediment concentration at each river section can be calculated. The presented 1D flow and suspended sediment transport model has been applied to the Pearl River networks and can reproduce water levels, discharges, and suspended sediment concentration with good accuracy, indicating this that model can be used to simulate the hydrodynamics and suspended sediment concentration in the distributary channel networks.

Final Technical Report for Award DESC0011912, "Trimodal Tapping Mode Atomic Force Microscopy: Simultaneous 4D Mapping of Conservative and Dissipative Probe-Sample Interactions of Energy-Relevant Materials”

Energy Technology Data Exchange (ETDEWEB)

Solares, Santiago D. [George Washington Univ., Washington, DC (United States)

2017-09-22

The final project report covering the period 7/1/14-6/30/17 provides an overview of the technical accomplishments in the areas of (i) fundamental viscoelasticity, (ii) multifrequency atomic force microscopy, and (iii) characterization of energy-relevant materials with atomic force microscopy. A list of publications supported by the project is also provided.

Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility

International Nuclear Information System (INIS)

Kirchner, Thomas B.

2002-01-01

The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

Final Technical Progress Report Long term risk from actinides in the environment: Modes of mobility

Energy Technology Data Exchange (ETDEWEB)

Thomas B. Kirchner

2002-03-22

The key source of uncertainty in assessing actinide mobility is the relative importance of transport by: (1) wind erosion, (2) water erosion, and (3) vertical migration. Each of these three processes depends on several environmental factors and they compete with one another. A scientific assessment of the long-term risks associated with actinides in surface soils depends on better quantifying each of these three modes of mobility. The objective from our EMSP study was to quantify the mobility of soil actinides by wind erosion, water erosion, and vertical migration at three semiarid sites where actinide mobility is a key technical, social and legal issue. This EMSP project was the first to evaluate all three factors at a site. The approach has been to investigate both short- and long-term issues based on field and lab studies and model comparisons. Our results demonstrate the importance of incorporating threshold responses into a modeling framework that accounts for environmental factors and natural disturbances that trigger large changes in actinide mobility. The study measured erosional losses of sediment and fallout cesium (an actinide analogue) from field plots located near WIPP in 1998. The results highlight the large effect of burning as a disturbance on contaminant transport and mobility via runoff and erosion. The results show that runoff, erosion, and actinide transport are (1) strongly site specific-differences in radionuclide transport between WIPP and Rocky Flats differed by a factor of twelve because of soil and vegetation differences, and (2) are strongly impacted by disturbances such as fire, which can increase runoff, erosion, and actinide transport by more than an order of magnitude. In addition, a laboratory experiment using soil columns was conducted to investigate the vertical transport of contaminants in sandy soils. Nine columns of soil collected from the vicinity of the WIPP site were prepared. The column consisted of a piece of PVC pipe 20 cm

The role of non-technical skills in surgery.

Science.gov (United States)

Agha, Riaz A; Fowler, Alexander J; Sevdalis, Nick

2015-12-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care.

The role of non-technical skills in surgery

Science.gov (United States)

Agha, Riaz A.; Fowler, Alexander J.; Sevdalis, Nick

2015-01-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care. PMID:26904193

Biogeochemical malfunctioning in sediments beneath a deep-water fish farm.

Science.gov (United States)

Valdemarsen, Thomas; Bannister, Raymond J; Hansen, Pia K; Holmer, Marianne; Ervik, Arne

2012-11-01

We investigated the environmental impact of a deep water fish farm (190 m). Despite deep water and low water currents, sediments underneath the farm were heavily enriched with organic matter, resulting in stimulated biogeochemical cycling. During the first 7 months of the production cycle benthic fluxes were stimulated >29 times for CO(2) and O(2) and >2000 times for NH(4)(+), when compared to the reference site. During the final 11 months, however, benthic fluxes decreased despite increasing sedimentation. Investigations of microbial mineralization revealed that the sediment metabolic capacity was exceeded, which resulted in inhibited microbial mineralization due to negative feed-backs from accumulation of various solutes in pore water. Conclusions are that (1) deep water sediments at 8 °C can metabolize fish farm waste corresponding to 407 and 29 mmol m(-2) d(-1) POC and TN, respectively, and (2) siting fish farms at deep water sites is not a universal solution for reducing benthic impacts. Copyright © 2012 Elsevier Ltd. All rights reserved.

Final Technical Report - SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodynamics

International Nuclear Information System (INIS)

Schnack, Dalton D.

2012-01-01

Final technical report for research performed by Dr. Thomas G. Jenkins in collaboration with Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodyanics, DE-FC02-06ER54899, for the period of 8/15/06 - 8/14/11. This report centers on the Slow MHD physics campaign work performed by Dr. Jenkins while at UW-Madison and then at Tech-X Corporation. To make progress on the problem of RF induced currents affect magnetic island evolution in toroidal plasmas, a set of research approaches are outlined. Three approaches can be addressed in parallel. These are: (1) Analytically prescribed additional term in Ohm's law to model the effect of localized ECCD current drive; (2) Introduce an additional evolution equation for the Ohm's law source term. Establish a RF source 'box' where information from the RF code couples to the fluid evolution; and (3) Carry out a more rigorous analytic calculation treating the additional RF terms in a closure problem. These approaches rely on the necessity of reinvigorating the computation modeling efforts of resistive and neoclassical tearing modes with present day versions of the numerical tools. For the RF community, the relevant action item is - RF ray tracing codes need to be modified so that general three-dimensional spatial information can be obtained. Further, interface efforts between the two codes require work as well as an assessment as to the numerical stability properties of the procedures to be used.

Cyclic Sediment Trading Between Channel and River Bed Sediments

Science.gov (United States)

Haddadchi, A.

2015-12-01

Much of the previous work on sediment tracing has focused on determining either the initial sources of the sediment (soils derive from a particular rock type) or the erosion processes generating the sediment. However, alluvial stores can be both a source and sink for sediment transported by streams. Here geochemical and fallout radionuclide tracing of river-bed and alluvial sediments are used to determine the role of secondary sources, sediment stores, as potential sources of sediment leaving Emu Creek catchment, southeastern Queensland, Australia. Activity concentrations of 137Cs on the river sediments are consistent with channel erosion being the dominant source at all sites sampled along the river. To characterise the deposition and remobilisation cycles in the catchment, a novel geochemical tracing approach was used. Successive pockets of alluvium were treated as discrete sink terms within geochemical mixing models and their source contributions compared with those of river bed sediments collected adjacent to each alluvial pocket. Three different size fractions were examined; silts and clays (banks indicates a high degree of 'trading' between the fluvial space and the alluvial space. Hence, management works aimed at primarily reducing the supply of sediments to the outlet of Emu Creek should focus on rehabilitation of channel banks in the lower catchment.

Sediment Burial Intolerance of Marine Macroinvertebrates.

Directory of Open Access Journals (Sweden)

Vicki J Hendrick

Full Text Available The marine environment contains suspended particulate matter which originates from natural and anthropogenic sources. Settlement of this material can leave benthic organisms susceptible to smothering, especially if burial is sudden i.e. following storms or activities such as dredging. Their survival will depend on their tolerance to, and their ability to escape from burial. Here we present data from a multi-factorial experiment measuring burial responses incorporating duration, sediment fraction and depth. Six macroinvertebrates commonly found in sediment rich environments were selected for their commercial and/or conservation importance. Assessments revealed that the brittle star (Ophiura ophiura, the queen scallop (Aequipecten opercularis and the sea squirt (Ciona intestinalis were all highly intolerant to burial whilst the green urchin (Psammichinus miliaris and the anemone (Sagartiogeton laceratus, showed intermediate and low intolerance respectively, to burial. The least intolerant, with very high survival was the Ross worm (Sabellaria spinulosa. With the exception of C. intestinalis, increasing duration and depth of burial with finer sediment fractions resulted in increased mortality for all species assessed. For C. intestinalis depth of burial and sediment fraction were found to be inconsequential since there was complete mortality of all specimens buried for more than one day. When burial emergence was assessed O. ophiura emerged most frequently, followed by P. miliaris. The former emerged most frequently from the medium and fine sediments whereas P. miliaris emerged more frequently from coarse sediment. Both A. opercularis and S. laceratus showed similar emergence responses over time, with A. opercularis emerging more frequently under coarse sediments. The frequency of emergence of S. laceratus increased with progressively finer sediment and C. intestinalis did not emerge from burial irrespective of sediment fraction or depth. Finally

AIPM Final Report

Energy Technology Data Exchange (ETDEWEB)

John Mookken

2006-06-30

The final AIPM project report consists of six sections. Each section includes information on the original AIPM project and extension work on the high temperature design. The first section (1) provides an overview of the program and highlights the significant targets to meet at the end of the program. The next section (2) summarizes the significant technical accomplishments by the SEMIKRON AIPM team during the course of the project. Greater technical details are provided in a collection of all the quarterly reports which can be found in the appendix. Section three (3) presents some the more significant technical data collected from technology demonstrators. Section four (4) analyzes the manufacturing cost or economic aspects of producing 100,000 units/yr. Section five (5) describes the commercialization efforts of the AIPM technology into the automotive market. The last section (6) recommends follow on work that will build on the efforts and achievements of the AIPM program.

ITER technical advisory committee meeting

International Nuclear Information System (INIS)

Fujiwara, M.

2001-01-01

The 17th Meeting of the ITER Technical Advisory Committee (TAC-17) was held on February 19-22, the ITER Garching Work Site in Germany. The objective of the meeting was to review the Draft Final Design Report of ITER-FEAT and assess the ability of the self-consistent overall design both to satisfy the technical objectives previously defined and to meet the cost limitations. TAC-17 was also organized to confirm that the design and critical elements, with emphasis on the key recommendations made at previous TAC meetings, are such as to extend the confidence in starting ITER construction. It was also intended to provide the ITER Council, scheduled to meet on 27 and 28 February in Toronto, with a technical assessment and key recommendations of the above mentioned report

Reconstruction of the sediment flow regime in a semi-arid Mediterranean catchment using check dam sediment information.

Science.gov (United States)

Bussi, G.; Rodríguez, X.; Francés, F.; Benito, G.; Sánchez-Moya, Y.; Sopeña, A.

2012-04-01

assign a date to every flood unit. The TETIS-SED model provides the sediment yield series divided into textural fractions (sand, silt and clay). In order to determine the amount of sediments trapped into the ponds, trap efficiency of each check dam is computed by using the STEP model (Sediment Trap Efficiency model for small Ponds, Verstraeten and Poesen, 2001). Sediment dry bulk density is calculated according to Lane and Koelzer (1943) formulae. In order to improve the reliability of the flood reconstruction, distributed historical fire data has also been used for dating carbon layers found in the depositional sequence. Finally, a date has been assigned to every flood unit, corresponding to an extreme rainfall event; the result is a sediment volume series from 1990 to 2009, which may be very helpful for validating both hydrological and sediment yield models and can improve our understanding on erosion and sediment yield in this catchment.

Technical specification improvements to containment heat removal and emergency core cooling systems: Final report

International Nuclear Information System (INIS)

Sullivan, W.P.; Ha, C.; Pentzien, D.C.; Visweswaran, S.

1988-07-01

This report presents the results of an analysis for technical specification improvements to the emergency core cooling systems (ECCS) and containment heat removal systems (EPRI Research Project 2142-3). The objective of this project is to further develop a reliability- and risk-based methodology to provide improvements by considering groups of surveillance test intervals and allowed out-of-service times jointly. This was done for the technical specifications for the ECCS, containment heat removal equipment, and supporting systems of a boiling water reactor plant. The project (1) developed a methodology for optimizing groups of surveillance test intervals and allowed out-of-service times jointly, (2) applied the methodology in a case study of a specific operating plant, Hatch-2, and (3) evaluated benefits of the application. The results of the case study demonstrate that beneficial technical specification improvements can be realized with application of the methodology. By tightening a small group of sensitive surveillance test intervals (STIs) and allowed out-of-service times (AOTs), a larger group of less sensitive STIs and AOTs can be extended resulting in an overall plant operating cost improvement without reducing the plant safety. The reliability- and risk-based methodology and results from this project can be effectively applied for technical specification improvements at other operating plants

ITER EDA technical activities

International Nuclear Information System (INIS)

Aymar, R.

1998-01-01

Six years of technical work under the ITER EDA Agreement have resulted in a design which constitutes a complete description of the ITER device and of its auxiliary systems and facilities. The ITER Council commented that the Final Design Report provides the first comprehensive design of a fusion reactor based on well established physics and technology

Field manual for stream sediment reconnaissance. Savannah River Laboratory National Uranium Resource Evaluation Program

International Nuclear Information System (INIS)

Ferguson, R.B.; Price, V.; Baucom, E.I.

1976-07-01

A manual is presented that is intended to direct and coordinate field operations, site selection, stream sediment sample collection, water sample collection, and information codes for the Savannah River Laboratory (SRL) contribution to the National Uranium Resource Evaluation (NURE) program. The manual provides public relations information for field sampling teams as well as technical direction

DOE Utility Matching Program Final Technical Report

International Nuclear Information System (INIS)

Haghighat, Alireza

2002-01-01

This is the Final report for the DOE Match Grant (DE-FG02-99NE38163) awarded to the Nuclear and Radiological Engineering (NRE) Department, University of Florida, for the period of September 1999 to January 2002. This grant has been instrumental for maintaining high-quality graduate and undergraduate education at the NRE department. The grant has been used for supporting student entry and retention and for upgrading nuclear educational facilities, nuclear instrumentation, computer facilities, and computer codes to better enable the incorporation of experimental experiences and computer simulations related to advanced light water fission reactor engineering and other advanced reactor concepts into the nuclear engineering course curricula

Sediment fluxes and the littoral drift along northeast Andhra Pradesh Coast, India: estimation by remote sensing.

Science.gov (United States)

Kunte, Pravin D; Alagarsamy, R; Hursthouse, A S

2013-06-01

The littoral drift regime along the northeastern coast of India was investigated by analyzing coastal drift indicators and shoreline changes based on multitemporal satellite images. The study of offshore turbidity patterns and quantitative estimation of suspended sediments was undertaken to understand the magnitude and direction of movement of sediment fluxes. The study revealed that: (1) the character of coastal landforms and sedimentation processes indicate that the sediment transport is bidirectional and monsoon dependent; (2) multidate, multitemporal analysis of satellite images helps to show the nature of sediment transport along the coast. The dominant net sediment transport is in a NE direction along the eastern coast of India. Finally, this assessment demonstrates the potential of remote sensing technology in understanding the coastal morphometric changes, long-term sediment transport, shoreline changes, and offshore turbidity distribution pattern and the implications for the transport of sediment-associated pollutants.

Experimental investigation on consistency limits of cement and lime-stabilized marine sediments.

Science.gov (United States)

Wang, DongXing; Zentar, Rachid; Abriak, Nor Edine; Xu, WeiYa

2012-06-01

This paper presents the effects of treatments with cement and lime on the consistency limits of marine sediments dredged from Dunkirk port. The Casagrande percussion test and the fall cone test were used to determine the liquid limits of raw sediments and treated marine sediments. For the evaluation of the plastic limits, the results of the fall cone test were compared with those obtained by the rolling test method. The relationship between the water contents and the penetration depths for the determination of the liquid limit and the plastic limit was explored. Liquid limits at 15.5 mm and plastic limits at 1.55 mm seem to be a more appropriate choice for the studied marine sediments compared with the limits determined by other used prediction methods. Finally, the effect of cement treatment and lime treatment on the Casagrande classification of the studied sediments was investigated according to the different prediction results.

Rainfall, runoff and sediment transport in a Mediterranean mountainous catchment.

Science.gov (United States)

Tuset, J; Vericat, D; Batalla, R J

2016-01-01

The relation between rainfall, runoff, erosion and sediment transport is highly variable in Mediterranean catchments. Their relation can be modified by land use changes and climate oscillations that, ultimately, will control water and sediment yields. This paper analyses rainfall, runoff and sediment transport relations in a meso-scale Mediterranean mountain catchment, the Ribera Salada (NE Iberian Peninsula). A total of 73 floods recorded between November 2005 and November 2008 at the Inglabaga Sediment Transport Station (114.5 km(2)) have been analysed. Suspended sediment transport and flow discharge were measured continuously. Rainfall data was obtained by means of direct rain gauges and daily rainfall reconstructions from radar information. Results indicate that the annual sediment yield (2.3 t km(-1) y(-1) on average) and the flood-based runoff coefficients (4.1% on average) are low. The Ribera Salada presents a low geomorphological and hydrological activity compared with other Mediterranean mountain catchments. Pearson correlations between rainfall, runoff and sediment transport variables were obtained. The hydrological response of the catchment is controlled by the base flows. The magnitude of suspended sediment concentrations is largely correlated with flood magnitude, while sediment load is correlated with the amount of direct runoff. Multivariate analysis shows that total suspended load can be predicted by integrating rainfall and runoff variables. The total direct runoff is the variable with more weight in the equation. Finally, three main hydro-sedimentary phases within the hydrological year are defined in this catchment: (a) Winter, where the catchment produces only water and very little sediment; (b) Spring, where the majority of water and sediment is produced; and (c) Summer-Autumn, when little runoff is produced but significant amount of sediments is exported out of the catchment. Results show as land use and climate change may have an important

Biological treatment of PAH-contaminated sediments in a Sequencing Batch Reactor

International Nuclear Information System (INIS)

Chiavola, Agostina; Baciocchi, Renato; Gavasci, Renato

2010-01-01

The technical feasibility of a sequential batch process for the biological treatment of sediments contaminated by polycyclic aromatic hydrocarbons (PAHs) was evaluated through an experimental study. A bench-scale Sediment Slurry Sequencing Batch Reactor (SS-SBR) was fed with river sediments contaminated by a PAH mixture made by fluorene, anthracene, pyrene and crysene. The process performance was evaluated under different operating conditions, obtained by modifying the influent organic load, the feed composition and the hydraulic residence time. Measurements of the Oxygen Uptake Rates (OURs) provided useful insights on the biological kinetics occurring in the SS-SBR, suggesting the minimum applied cycle time-length of 7 days could be eventually halved, as also confirmed by the trend observed in the volatile solid and total organic carbon data. The removal efficiencies gradually improved during the SS-SBR operation, achieving at the end of the study rather constant removal rates above 80% for both 3-rings PAHs (fluorene and anthracene) and 4-ring PAHs (pyrene and crysene) for an inlet total PAH concentration of 70 mg/kg as dry weight (dw).

Energy generation and the sulfur-carbon cycles: Final technical report for period March 1981 thru February 1985

International Nuclear Information System (INIS)

Zeikus, J.G.

1987-05-01

The aim of this research was to understand the role of anaerobic bacteria in natural and man-influenced carbon cycles in nature. The major goal was to elucidate how sulfur metabolism influenced organic decomposition in aquatic sediments. The research compared these processes in two different anaerobic ecosystems: the sulfate-depleted sediments of Lake Mendota, Wisconsin and the sulfate-saturated sediments of Great Salt Lake, Utah. The approach was both ecological and physiological, and employed both in situ characterization of carbon and sulfur metabolism with radiotracers and laboratory species isolation-characterization studies with pure and defined mixed cultures to demonstrate the prevalent environmental paths of carbon electrons, and sulfur during the anaerobic decomposition of organic matter. The significance of this research encompassed fundamental knowledge of the carbon sulfur cycles, applied knowledge on the microbial genesis of flammable gas and oil and extended knowledge on the diversity and metabolic activity of obligately anaerobic bacteria in nature. 13 refs

Technical-tactical analysis of youth olympic taekwondo combat.

Science.gov (United States)

Tornello, Francesco; Capranica, Laura; Minganti, Carlo; Chiodo, Salvatore; Condello, Giancarlo; Tessitore, Antonio

2014-04-01

The purpose of this study was to define the technical and tactical profiles of official youth taekwondo competitions played under the most recent rules of the International Taekwondo Federation. Tactical actions (i.e., attack, defense, and block), technical executions (from 1- to 4-point scores), kicking legs (i.e., front/rear and right/left), and overall technical effectiveness were investigated in relation to match outcome of semifinal and final competitions (n = 50) of youth (aged 13-14 years) black belt athletes during the Italian Taekwondo Cadet Championship. Differences (p technical exchanges showed differences (p technical executions. Winners resulted more efficient (p technical and tactical variables. In general, these findings showed that Cadets tend to adopt an offensive strategy. In considering that the adoption of the new electronic system requires athletes to execute correct technical actions to have a score assigned, coaches should emphasize the effectiveness of scoring techniques and help athletes to effectively improve their defense and counterattack capabilities.

Suspended sediment and sediment-associated contaminants in San Francisco Bay

Science.gov (United States)

Schoellhamer, D.H.; Mumley, T.E.; Leatherbarrow, J.E.

2007-01-01

Water-quality managers desire information on the temporal and spatial variability of contaminant concentrations and the magnitudes of watershed and bed-sediment loads in San Francisco Bay. To help provide this information, the Regional Monitoring Program for Trace Substances in the San Francisco Estuary (RMP) takes advantage of the association of many contaminants with sediment particles by continuously measuring suspended-sediment concentration (SSC), which is an accurate, less costly, and more easily measured surrogate for several trace metals and organic contaminants. Continuous time series of SSC are collected at several sites in the Bay. Although semidiurnal and diurnal tidal fluctuations are present, most of the variability of SSC occurs at fortnightly, monthly, and semiannual tidal time scales. A seasonal cycle of sediment inflow, wind-wave resuspension, and winnowing of fine sediment also is observed. SSC and, thus, sediment-associated contaminants tend to be greater in shallower water, at the landward ends of the Bay, and in several localized estuarine turbidity maxima. Although understanding of sediment transport has improved in the first 10 years of the RMP, determining a simple mass budget of sediment or associated contaminants is confounded by uncertainties regarding sediment flux at boundaries, change in bed-sediment storage, and appropriate modeling techniques. Nevertheless, management of sediment-associated contaminants has improved greatly. Better understanding of sediment and sediment-associated contaminants in the Bay is of great interest to evaluate the value of control actions taken and the need for additional controls. ?? 2007 Elsevier Inc. All rights reserved.

The contribution of bank and surface sediments to fluvial sediment ...

African Journals Online (AJOL)

The contribution of bank and surface sediments to fluvial sediment transport of the Pra River. ... the relative contribution of surface and bank sediments to the fluvial sediment transport. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Astrobee Periodic Technical Review (PTR) Delta 3

Science.gov (United States)

Provencher, Christopher; Smith, Marion F.; Smith, Ernest Everett; Bualat, Maria Gabriele; Barlow, Jonathan Spencer

2017-01-01

Astrobee is a free flying robot for the inside of the International Space Station (ISS). The Periodic Technical Review (PTR) delta 3 is the final design review of the system presented to stakeholders.

FINAL TECHNICAL REPORT: 20% Wind by 2030: Overcoming the Challenges

Energy Technology Data Exchange (ETDEWEB)

Tom Kaiserski; Dan Lloyd

2012-02-28

The funds allocated through the Wind Powering America (WPA) grant were utilized by the State of Montana to support broad outreach activities communicating the benefits and opportunities of increased wind energy and transmission development. The challenges to increased wind development were also clearly communicated with the understanding that a clearer comprehension of the challenges would be beneficial in overcoming the obstacles to further development. The ultimate purpose of these activities was to foster the increased development of Montana's rich wind resources through increased public acceptance and wider dissemination of technical resources.

Final Technical Report for subcontract number B612144

Energy Technology Data Exchange (ETDEWEB)

Mayali, X. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Marcu, O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-11

The original statement of work stipulated that the Subcontractor shall perform bacterial and algal cultivation and manipulation, microbe isolation, preparation of samples for sequencing and isotopic analysis, data analysis, and manuscript preparation. The Subcontractor shall work closely with Dr. Mayali and other LLNL scientists, and shall participate in monthly SFA meetings (either in person or by telephone). The Subcontractor shall deliver a final report at the conclusion of the work.

Final Scientific/Technical Report for award DE-FC--07-00AL67053

International Nuclear Information System (INIS)

Dixon, Cathy

2005-01-01

The project ''Creating an Educational Consortium to Support the Recruitment and Retention of Expertise for the Nuclear Weapons Complex'' was also known as the Advanced Fuel Cycle Initiative (AFCI) University Fellowship Program. Since its inception, the Advanced Fuel Cycle Initiative program and its predecessor, the Advanced Accelerator Applications (AAA) program, have engaged university researchers and students in the sciences necessary to answer technical questions related to reducing high-level waste volumes, optimizing the economics and performance of Yucca Mountain, reducing the technical need for a second repository, reducing the long-term inventories of plutonium in spent fuel, and enabling the proliferation-resistant recovery of the energy contained in spent fuel. The Advanced Fuel Cycle University Fellowship Program is intended to support top students across the nation in a variety of disciplines that will be required to support transmutation research and technology development in the coming decades

Basic concepts for crew resource management and non-technical skills.

Science.gov (United States)

Flin, Rhona; Maran, Nikki

2015-03-01

In this paper, we explain the conceptual background to non-technical skills and show how they can influence job performance in anaesthesia. We then describe the taxonomy of anaesthetists' non-technical skills (ANTS) and related systems, such as ANTS-AP for anaesthetic practitioners. We discuss the training courses that have been designed to teach these non-technical skills, which are called crew resource management (CRM), crisis resource management (CRM) or crisis avoidance resource management (CARMA). Finally, we discuss the application of non-technical skills assessment systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

Can control of soil erosion mitigate water pollution by sediments?

Science.gov (United States)

Rickson, R J

2014-01-15

The detrimental impact of sediment and associated pollutants on water quality is widely acknowledged, with many watercourses in the UK failing to meet the standard of 'good ecological status'. Catchment sediment budgets show that hill slope erosion processes can be significant sources of waterborne sediment, with rates of erosion likely to increase given predicted future weather patterns. However, linking on-site erosion rates with off-site impacts is complicated because of the limited data on soil erosion rates in the UK and the dynamic nature of the source-pathway-receptor continuum over space and time. Even so, soil erosion control measures are designed to reduce sediment production (source) and mobilisation/transport (pathway) on hill slopes, with consequent mitigation of pollution incidents in watercourses (receptors). The purpose of this paper is to review the scientific evidence of the effectiveness of erosion control measures used in the UK to reduce sediment loads of hill slope origin in watercourses. Although over 73 soil erosion mitigation measures have been identified from the literature, empirical data on erosion control effectiveness are limited. Baseline comparisons for the 18 measures where data do exist reveal erosion control effectiveness is highly variable over time and between study locations. Given the limitations of the evidence base in terms of geographical coverage and duration of monitoring, performance of the different measures cannot be extrapolated to other areas. This uncertainty in effectiveness has implications for implementing erosion/sediment risk reduction policies, where quantified targets are stipulated, as is the case in the EU Freshwater Fish and draft Soil Framework Directives. Also, demonstrating technical effectiveness of erosion control measures alone will not encourage uptake by land managers: quantifying the costs and benefits of adopting erosion mitigation is equally important, but these are uncertain and difficult to

Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Reeder, Richard [Stony Brook Univ., NY (United States); Phillips, Brian [Stony Brook Univ., NY (United States)

2017-10-18

A variety of calcifying organisms produce a transient or metastable amorphous calcium carbonate (ACC) precursor phase that is assembled and subsequently transformed into a crystalline biomineral, typically calcite or aragonite. The complex shapes, hierarchical structures, and unique physical properties of the biominerals that result from this calcification pathway have stimulated interest in adapting these concepts for the design and creation of bio-inspired functional materials in the laboratory. ACC also forms as a reactive precursor in diverse inorganic systems and is likely to play a much broader role in calcium carbonate formation. Knowledge of the structure, composition, and behavior of this metastable phase is critical for establishing a structural and mechanistic framework for calcium carbonate formation and its role in biogeochemical processes, including carbon cycling. Minor additives, such as magnesium, phosphorus, and organic macromolecules, are known to play important roles in controlling ACC stability, transformation kinetics, and selection of final crystalline polymorph. Molecular water also occurs in many types of ACC and is thought to play a structural role in its stability and transformation behavior. One of the major challenges that remain unresolved is identification of the structural basis for the role of these minor additives and molecular water. The absence of long-range order in ACC, and other amorphous phases, has posed a challenge for study by techniques commonly used for crystalline solids. Preliminary studies in our group show that the combination of two techniques, synchrotron X-ray-based pair distribution function (PDF) analysis and nuclear magnetic resonance (NMR) spectroscopy can provide entirely new insight to structural properties of synthetic ACC over length scales that are most relevant for understanding its transformation properties. Building on preliminary experiments, we propose a systematic study of synthesis, structure, and

Sedimentation technique of waste bituminization and thermogravimetric characteristics of the final products

Energy Technology Data Exchange (ETDEWEB)

Zeger, J; Knotik, K; Jakusch, H

1976-01-01

In the research centre of the Oesterreichische Studiengesellschaft fuer Atomenergie GesmbH a semitechnical plant has been installed for waste bituminization, which has been tested inactively since 1973. This plant is using a new technological process for embedding. One of the important features of this new process is that the, normally inactive solution water is distilled off prior to the embedding, resulting in dry and powdery salts. The second important feature is that the mixing of these dry salts with the thin fluid bitumen is done by sedimentation. Expecially there is no mechanical aid used for mixing. Thermogravimetric analysis of samples which simulated the final products of this pilot plant, were carried out to verify the best working parameters and to study the possible chemical damage to the bitumen. Analysis was performed by heating the samples, consisting of various mixtures of bitumen and inorganic salts, in a METTLER-Thermoanalyzer up to 500/sup 0/C using different atmospheres (air, nitrogen). It could be shown that only nitrate and nitrite especially in combination with Fe(III)-ions are of negative influence on the thermostability of bitumen. They lead to a sudden and quick weight loss of the samples between 370 and 410/sup 0/C (above the melting point of both NaNO/sub 2/ and NaNO/sub 3/). The Fe-ions hava a catalytic influence, as it could be shown that 1 1% addiation of Fe(NO/sub 3/)/sub 3/ to NaNO/sub 3/ leads to a considerable acceleration of the incineration. This influence of the Fe(III)-ion can be suppressed to some extend by a hydrolysis prior to the embedding. In preparation of further studies concerning the behaviour of radiation damaged bitumen there has been developed a method of measuring the dose rate of an unknown radioactive salt mixture at any point of this mixture. This is done by making two measurements with glass dosimeters. One with a beta-absorber to get a pure gamma-dose and the other without it to get the combined beta and

Final Technical Report: "Achieving Regional Energy Efficiency Potential in the Southeast”

Energy Technology Data Exchange (ETDEWEB)

Mahoney, Mandy [Southeast Energy Efficiency Alliance (SEEA), Atlanta, GA (United States)

2018-03-07

The overall objective of this award was to facilitate sharing of DOE resources and best practices as well as provide technical assistance to key stakeholders to support greater compliance with energy efficiency standards and increased energy savings. The outcomes of this award include greater awareness among key stakeholders on energy efficiency topics, increased deployment and utilization of DOE resources, and effective policies and programs to support energy efficiency in the Southeast.

Technical Guidelines on Performing a Sediment Erosion and Deposition Assessment (SEDA) at Superfund Sites

Science.gov (United States)

2014-09-01

introduced to a water body because of the failure of a river bank due to, for example, flow-induced erosion of the bank toe and/or surface, or...under supercritical flows (with Froude number greater than one). Antidunes are usually more symmetrical (in their longitudinal profile) than dunes ... dunes , and anti- dunes . Bedload Sediment material moving on top of or near a channel bed by rolling, sliding, and saltating, i.e., jumping

Final strip mine regs released

Energy Technology Data Exchange (ETDEWEB)

1977-12-12

The final interim surface mining regulations were published by the Office of Surface Mining on 12 December. Among the requirements are that the operation should minimize disturbances to the prevailing hydrological balance in order to prevent long-term adverse changes in water quality and quantity, in the depth of ground water and in the location of surface water drainage channels. Regulations for sedimentation ponds are retained but exemption may be granted to allow the pH to rise above 9 if manganese levels (4 mg/l) cannot be met. The 24-hour frequency event for which effluent limitations must be applied has been reduced from 25 years to 10 years. Large sedimentation ponds must be constructed to withstand, at a minimum, a 100-year frequency, 6-hour duration storm. The regulations are to take effect on the 3rd of May 1978.

ITER technical basis

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-01-01

Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties.

ITER technical basis

International Nuclear Information System (INIS)

2002-01-01

Following on from the Final Report of the EDA(DS/21), and the summary of the ITER Final Design report(DS/22), the technical basis gives further details of the design of ITER. It is in two parts. The first, the Plant Design specification, summarises the main constraints on the plant design and operation from the viewpoint of engineering and physics assumptions, compliance with safety regulations, and siting requirements and assumptions. The second, the Plant Description Document, describes the physics performance and engineering characteristics of the plant design, illustrates the potential operational consequences foe the locality of a generic site, gives the construction, commissioning, exploitation and decommissioning schedule, and reports the estimated lifetime costing based on data from the industry of the EDA parties

Decontamination and functional reclamation of dredged brackish sediments.

Science.gov (United States)

Doni, S; Macci, C; Peruzzi, E; Iannelli, R; Ceccanti, B; Masciandaro, G

2013-07-01

The continuous stream of sediments, dredged from harbors and waterways for keeping shipping traffic efficiency, is a considerable ongoing problem recognized worldwide. This problem gets worse as most of the sediments dredged from commercial ports and waterways turn out to be polluted by a wide range of organic and inorganic contaminants. In this study, phytoremediation was explored as a sustainable reclamation technology for turning slightly-polluted brackish dredged sediments into a matrix feasible for productive use. To test this possibility, a phytoremediation experimentation was carried out in containers of about 0.7 m(3) each, filled with brackish dredged sediments contaminated by heavy metals and hydrocarbons. The sediments were pre-conditioned by adding an agronomic soil (30 % v/v) to improve their clayey granulometric composition, and by topping the mixture with high quality compost (4 kg m(-2)) to favour the initial adaptation of the selected vegetal species. The following plant treatments were tested: (1) Paspalum vaginatum, (2) Phragmites australis, (3) Spartium junceum + P. vaginatum, (4) Nerium oleander + P. vaginatum, (5) Tamarix gallica + P. vaginatum, and (6) unplanted control. Eighteen months after the beginning of the experimentation, all the plant species were found in healthy condition and well developed. Throughout the whole experiment, the monitored biological parameters (total microbial population and dehydrogenase activity) were generally observed as constantly increasing in all the planted sediments more than in the control, pointing out an improvement of the chemico-physical conditions of both microorganisms and plants. The concentration decrease of organic and inorganic contaminants (>35 and 20 %, respectively) in the treatments with plants, particularly in the T. gallica + P. vaginatum, confirmed the importance of the root-microorganism interaction in activating the decontamination processes. Finally, the healthy state of

Final Scientific/Technical Report Solar America Initiative: Solar Outreach and Communications

Energy Technology Data Exchange (ETDEWEB)

Weissman, Jane M

2011-09-10

The purpose of the Solar America Initiative: Solar Outreach and Communications grant was to promote better communications among stakeholders; address infrastructure barriers to solar energy; and coordinate with industry, the U.S. Department of Energy, national laboratories, states, cities and counties. The Interstate Renewable Energy Council (IREC), a non-profit organization formed in 1982, approached this grant project by establishing a wide range of communication and outreach activities including newsletters, workshops, webinars, model practices and publications; by advancing easy and fair hook-up rules to the utility grid; and by upgrading training based on industry competency standards. The Connecting to the Grid project and the Solar Codes and Standards Public Hearings project offered communication coupled with technical assistance to overcome interconnection, net metering and other regulatory and program barriers. The Workforce Development Project tackled building a strong workforce through quality training and competency assessment programs. IREC's web site, the semi-monthly state and stakeholder newsletter and the metrics report resulted in better communications among stakeholders. Workshops and phone seminars offered technical assistance and kept stakeholders up-to-date on key issues. All of these activities resulted in implementing sustainable solutions to institutional and market barriers to solar energy and getting the right information to the right people.

Exploration of biodegradation mechanisms of black carbon-bound nonylphenol in black carbon-amended sediment

International Nuclear Information System (INIS)

Cheng, Guanghuan; Sun, Mingyang; Ge, Xinlei; Xu, Xinhua; Lin, Qi; Lou, Liping

2017-01-01

The present study aimed to investigate biodegradation mechanisms of black carbon (BC)-bound contaminants in BC-amended sediment when BC was applied to control organic pollution. The single-point Tenax desorption technique was applied to track the species changes of nonylphenol (NP) during biodegradation process in the rice straw carbon (RC)-amended sediment. And the correlation between the biodegradation and desorption of NP was analyzed. Results showed that microorganisms firstly degraded the rapid-desorbing NP (6 h Tenax desorption) in RC-amended sediment. The biodegradation facilitated the desorption of slow-desorbing NP, which was subsequently degraded as well (192 h Tenax desorption). Notably, the final amount of NP degradation was greater than that of NP desorption, indicating that absorbed NP by RC amendment can be degraded by microorganisms. Finally, the residual NP amount in RC-amended sediment was decided by RC content and its physicochemical property. Moreover, the presence of the biofilm was observed by the confocal laser scanning microscope (CLSM) and scanning electron microscope (SEM) so that microorganisms were able to overcome the mass transfer resistance and directly utilized the absorbed NP. Therefore, single-point Tenax desorption alone may not be an adequate basis for the prediction of the bioaccessibility of contaminants to microorganisms or bioremediation potential in BC-amended sediment. - Highlights: • Biodegradation mechanism of RC-bound NP in sediment was examined. • The microbe prioritized the degradation of NP in desorption fraction. • The microbe formed the biofilm to directly degrade part of non-desorbable NP. • Residual NP amount was decided by RC content and physicochemical property. • Quantifying biodegradation by bioavailability will underestimate the actual outcomes. - The microbes directly degrade the non-desorbable NP bound to amended RC, so quantifying the biodegradation only by desorption will underestimate the

Sediment supply versus local hydraulic controls on sediment transport and storage in a river with large sediment loads

Science.gov (United States)

Dean, David; Topping, David; Schmidt, John C.; Griffiths, Ronald; Sabol, Thomas

2016-01-01

The Rio Grande in the Big Bend region of Texas, USA, and Chihuahua and Coahuila, Mexico, undergoes rapid geomorphic changes as a result of its large sediment supply and variable hydrology; thus, it is a useful natural laboratory to investigate the relative importance of flow strength and sediment supply in controlling alluvial channel change. We analyzed a suite of sediment transport and geomorphic data to determine the cumulative influence of different flood types on changing channel form. In this study, physically based analyses suggest that channel change in the Rio Grande is controlled by both changes in flow strength and sediment supply over different spatial and temporal scales. Channel narrowing is primarily caused by substantial deposition of sediment supplied to the Rio Grande during tributary-sourced flash floods. Tributary floods have large suspended-sediment concentrations, occur for short durations, and attenuate rapidly downstream in the Rio Grande, depositing much of their sediment in downstream reaches. Long-duration floods on the mainstem have the capacity to enlarge the Rio Grande, and these floods, released from upstream dams, can either erode or deposit sediment in the Rio Grande depending upon the antecedent in-channel sediment supply and the magnitude and duration of the flood. Geomorphic and sediment transport analyses show that the locations and rates of sand erosion and deposition during long-duration floods are most strongly controlled by spatial changes in flow strength, largely through changes in channel slope. However, spatial differences in the in-channel sediment supply regulate sediment evacuation or accumulation over time in long reaches (greater than a kilometer).

FINAL TECHNICAL REPORT Chagas Prevention in Central America

International Development Research Centre (IDRC) Digital Library (Canada)

Carlota Monroy

INFORME FINAL: PROYECTO ID 106531 - 001. CORRESPONDIENTE AL PERIODO DEL 1 DE MARZO 2011 AL 31 DE MARZO 2014. CONTENIDO. 1. Información general ……………………………………………………………1. 2. Resumen del proyecto ………………………………………………………….2. 3. Metas objetivos ...

AISI Direct Steelmaking Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Aukrust, E.

1994-08-01

This final report deals with the results of a 5-yr project for developing a more energy-efficient, environmentally friendly, less costly process for producing hot metal than current coke ovens and blast furnaces. In the process, iron ore pellets are smelted in a foamy slag created by reaction of coal char with molten slag to produce CO. The CO further reacts with oxygen, which also reacts with coal volatile matter, to produce the heat necessary to sustain the endothermic reduction reaction. The uncombusted CO and H{sub 2} from the coal are used to preheat and prereduce hematite pellets for the most efficient use of the energy in the coal. Laboratory programs confirmed that the process steps worked. Pilot plant studies were successful. Economic analysis for a 1 million tpy plant is promising.

National Alliance for Advanced Biofuels and Bio-Products Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Olivares, Jose A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Baxter, Ivan [US Dept. of Agriculture (USDA)., Washington, DC (United States); Brown, Judith [Univ. of Arizona, Tucson, AZ (United States); Carleton, Michael [Matrix Genetics, Seattle, WA (United States); Cattolico, Rose Anne [Univ. of Washington, Seattle, WA (United States); Taraka, Dale [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Detter, John C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Devarenne, Timothy P. [Texas Agrilife Research, College Station, TX (United States); Dutcher, Susan K. [Washington Univ., St. Louis, MO (United States); Fox, David T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Goodenough, Ursula [Washington Univ., St. Louis, MO (United States); Jaworski, Jan [Donald Danforth Plant Science Center, St. Louis, MO (United States); Kramer, David [Michigan State Univ., East Lansing, MI (United States); Lipton, Mary S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); McCormick, Margaret [Matrix Genetics, Seattle, WA (United States); Merchant, Sabeeha [Univ. of California, Los Angeles, CA (United States); Molnar, Istvan [Univ. of Arizona, Tucson, AZ (United States); Panisko, Ellen A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pellegrini, Matteo [Univ. of California, Los Angeles, CA (United States); Polle, Juergen [City Univ. (CUNY), NY (United States). Brooklyn College; Sabarsky, Martin [Cellana, Inc., San Diego, CA (United States); Sayre, Richard T. [New Mexico Consortium, Los Alamos, NM (United States); Starkenburg,, Shawn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stormo, Gary [Washington Univ., St. Louis, MO (United States); Twary, Scott N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Unkefer, Clifford J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Unkefer, Pat J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Yuan, Joshua S. [Texas Agrilife Research, College Station, TX (United States); Arnold, Bob [Univ. of Arizona, Tucson, AZ (United States); Bai, Xuemei [Cellana, Inc., San Diego, CA (United States); Boeing, Wiebke [New Mexico State Univ., Las Cruces, NM (United States); Brown, Lois [Texas Agrilife Research, College Station, TX (United States); Gujarathi, Ninad [Reliance Industries Limited, Mumbai (India); Huesemann, Michael [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lammers, Pete [New Mexico State Univ., Las Cruces, NM (United States); Laur, Paul [Eldorado Biofuels, Santa Fe, NM (United States); Khandan, Nirmala [New Mexico State Univ., Las Cruces, NM (United States); Parsons, Ronald [Solix BioSystems, Fort Collins, CO (United States); Samocha, Tzachi [Texas Agrilife Research, College Station, TX (United States); Thomasson, Alex [Texas Agrilife Research, College Station, TX (United States); Unc, Adrian [New Mexico State Univ., Las Cruces, NM (United States); Waller, Pete [Univ. of Arizona, Tucson, AZ (United States); Bonner, James [Clarkson Univ., Potsdam, NY (United States); Coons, Jim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fernando, Sandun [Texas Agrilife Research, College Station, TX (United States); Goodall, Brian [Valicor Renewables, Dexter, MI (United States); Kadam, Kiran [Valicor Renewables, Dexter, MI (United States); Lacey, Ronald [Texas Agrilife Research, College Station, TX (United States); Wei, Liu [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Marrone, Babs [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Nikolov, Zivko [Texas Agrilife Research, College Station, TX (United States); Trewyn, Brian [Colorado School of Mines, Golden, CO (United States); Albrecht, Karl [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Capareda, Sergio [Texas Agrilife Research, College Station, TX (United States); Cheny, Scott [Diversified Energy, Gilbert, AZ (United States); Deng, Shuguang [New Mexico State Univ., Las Cruces, NM (United States); Elliott, Douglas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Cesar, Granda [Terrabon, LLC, Bryan, TX (United States); Hallen, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lupton, Steven [UOP Honeywell Co, LLC, Des Plaines, IL (United States); Lynch, Sharry [UOP Honeywell Co, LLC, Des Plaines, IL (United States); Marchese, Anthony [Colorado State Univ., Fort Collins, CO (United States); Nieweg, Jennifer [Albemarle Catilin, Ames, IA (United States); Ogden, Kimberly [Univ. of Arizona, Tucson, AZ (United States); Oyler, James [Genifuel, Salt Lake City, UT (United States); Reardon, Ken [Colorado State Univ., Fort Collins, CO (United States); Roberts, William [North Carolina State Univ., Raleigh, NC (United States); Sams, David [Albemarle Catilin, Ames, IA (United States); Schaub, Tanner [New Mexico State Univ., Las Cruces, NM (United States); Silks, Pete [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Archibeque, Shawn [Colorado State Univ., Fort Collins, CO (United States); Foster, James [Texas Agrilife Research, College Station, TX (United States); Gaitlan, Delbert [Texas Agrilife Research, College Station, TX (United States); Lawrence, Addison [Texas Agrilife Research, College Station, TX (United States); Lodge-Ivey, Shanna [New Mexico State Univ., Las Cruces, NM (United States); Wickersham, Tyron [Texas Agrilife Research, College Station, TX (United States); Blowers, Paul [Univ. of Arizona, Tucson, AZ (United States); Davis, Ryan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Downes, C. Meghan [New Mexico State Univ., Las Cruces, NM (United States); Dunlop, Eric [Pan Pacific Technologies Pty. Ltd., Adelaide (Australia); Frank, Edward [Argonne National Lab. (ANL), Argonne, IL (United States); Handler, Robert [Michigan Technological Univ., Houghton, MI (United States); Newby, Deborah [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pienkos, Philip [National Renewable Energy Lab. (NREL), Golden, CO (United States); Richardson, James [Texas Agrilife Research, College Station, TX (United States); Seider, Warren [Univ. of Pennsylvania, Philadelphia, PA (United States); Shonnard, David [Michigan Technological Univ., Houghton, MI (United States); Skaggs, Richard [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-09-30

The main objective of NAABB was to combine science, technology, and engineering expertise from across the nation to break down critical technical barriers to commercialization of algae-based biofuels. The approach was to address technology development across the entire value chain of algal biofuels production, from selection of strains to cultivation, harvesting, extraction, fuel conversion, and agricultural coproduct production. Sustainable practices and financial feasibility assessments ununderscored the approach and drove the technology development.

Estimated cumulative sediment trapping in future hydropower reservoirs in Africa

Science.gov (United States)

Lucía, Ana; Berlekamp, Jürgen; Zarfl, Christiane

2017-04-01

Despite a rapid economic development in Sub-Saharan Africa, almost 70% of the human population in this area remain disconnected from electricity access (International Energy Agency 2011). Mitigating climate change and a search for renewable, "climate neutral" electricity resources are additional reasons why Africa will be one key centre for future hydropower dam building, with only 8% of the technically feasible hydropower potential actually exploited. About 300 major hydropower dams with a total capacity of 140 GW are currently under construction (11.4%) or planned (88.6%) (Zarfl et al. 2015). Despite the benefits of hydropower dams, fragmentation of the rivers changes the natural flow, temperature and sediment regime. This has consequences for a high number of people that directly depend on the primary sector linked to rivers and floodplains. But sediment trapping in the reservoir also affects dam operation and decreases its life span. Thus, the objective of this work is to quantify the dimension of sediment trapping by future hydropower dams in African river basins. Soil erosion is described with the universal soil loss equation (Wischmeier & Smith 1978) and combined with the connectivity index (Cavalli et al. 2013) to estimate the amount of eroded soil that reaches the fluvial network and finally ends up in the existing (Lehner et al. 2011) and future reservoirs (Zarfl et al. 2015) per year. Different scenarios assuming parameter values from the literature are developed to include model uncertainty. Estimations for existing dams will be compared with literature data to evaluate the applied estimation method and scenario assumptions. Based on estimations for the reservoir volume of the future dams we calculated the potential time-laps of the future reservoirs due to soil erosion and depending on their planned location. This approach could support sustainable decision making for the location of future hydropower dams. References Cavalli, M., Trevisani, S., Comiti

76 FR 4645 - Hydrogen and Fuel Cell Technical Advisory Committee (HTAC)

Science.gov (United States)

2011-01-26

... DEPARTMENT OF ENERGY Hydrogen and Fuel Cell Technical Advisory Committee (HTAC) AGENCY: Department...: This notice announces a meeting of the Hydrogen and Fuel Cell Technical Advisory Committee (HTAC). HTAC... Agenda: (Subject to change; updates will be posted on http://hydrogen.energy.gov and copies of the final...

76 FR 60478 - Hydrogen and Fuel Cell Technical Advisory Committee (HTAC)

Science.gov (United States)

2011-09-29

... DEPARTMENT OF ENERGY Hydrogen and Fuel Cell Technical Advisory Committee (HTAC) AGENCY: Department...: The Hydrogen and Fuel Cell Technical Advisory Committee (HTAC) was established under section 807 of... website at: http://hydrogen.energy.gov and copies of the final agenda will available the date of the...

International Standards Development for Marine and Hydrokinetic Renewable Energy - Final Report on Technical Status

Energy Technology Data Exchange (ETDEWEB)

Rondorf, Neil E.; Busch, Jason; Kimball, Richard

2011-10-29

This report summarizes the progress toward development of International Standards for Marine and Hydrokinetic Renewable Energy, as funded by the U.S. Department of Energy (DOE) under the International Electrotechnical Commission (IEC) Technical Committee 114. The project has three main objectives: 1. Provide funding to support participation of key U.S. industry technical experts in 6 (originally 4) international working groups and/or project teams (the primary standards-making committees) and to attend technical meetings to ensure greater U.S. involvement in the development of these standards. 2. Provide a report to DOE and industry stakeholders summarizing the IEC standards development process for marine and hydrokinetic renewable energy, new international standards and their justifications, and provide standards guidance to industry members. 3. Provide a semi-annual (web-based) newsletter to the marine renewable energy community. The newsletter will educate industry members and stakeholders about the processes, progress, and needs of the US efforts to support the international standards development effort. The newsletter is available at www.TC114.us

A study of arsenic and chromium contamination in freshwater sediments

International Nuclear Information System (INIS)

Nazaratul Ashifa Abdullah Salim; Abdul Khalik Wood; Alias Mohd Yusof; Mohd Suhaimi Hamzah; Md Suhaimi Elias; Shamsiah Abdul Rahman

2008-08-01

Arsenic (As) is generally known for its toxicity while chromium (Cr) at the appropriate amount is an essential element to man and becomes quite toxic in excessive amount. Anthropogenic activities such as industrialization, agricultural and urbanization have led to the contamination of toxic elements into aquatic that finally end up in the sediment system. Environmental process like diagenetic process causes the toxic metals to migrate from the bedrock materials into the sediment surface and lastly into the water column. This process has been recognized to be the factor of arsenic contamination in well water in several countries such as Bangladesh, Taiwan, USA and Canada. A number of samples of freshwater sediments from identified rivers and lakes at Johor Bharu area had been analyzed to determine the concentration level of As and Cr using neutron activation analysis (NAA) technique. Certified Reference Material (CRM) namely BCSS-1 and IAEA Soil-7 were applied to provide good quality assurance control. The results obtained show that the concentrations of As in the rivers and lakes are 10-33 mg/g and 18-62 mg/g, respectively. The concentrations of Cr in the rivers range between 25 mg/g to125 mg/g, while in the lake sediments the concentrations range between 173 mg/g to 301 mg/g. The lakes sediments have higher As and Cr contents than the river sediment. The results of the As and Cr concentrations were then compared to the background value proposed by National Oceanic and Atmospheric Administration (NOAA), USA and interim freshwater sediment quality guidelines value established by Canadian Sediment Quality Guidelines for The Protection of Aquatic Life. (Author)

Final Scientific Technical Report Crowder College MARET Center

Energy Technology Data Exchange (ETDEWEB)

Boyt, Art [Crowder College, Neosho, MO (United States); Eberle, Dan [Crowder College, Neosho, MO (United States); Hudson, Pam [Crowder College, Neosho, MO (United States); Hopper, Russ [Crowder College, Neosho, MO (United States)

2013-06-30

, exploring and validating new applications of solar and other renewable technologies, the MARET Facility will house a wide variety of programs which will advance implementation of renewable energy throughout the region. These program goals include; Curriculum in renewable energy for pre-engineering transfer programs; Certification and degree programs for technical degrees for Energy Efficiency, Wind, Photovoltaic and Solar Thermal professionals; Short courses and workshops for building management and design professionals; Public education and demonstration projects in renewable energy through conferences and K-12 educational outreach; Technical degree offering in building construction incorporating “best practices” for energy efficiency and renewables; and Business incubators for new renewable energy businesses and new product development The new MARET facility will support the mission of the US Department of Energy (DOE) Solar Program, “to improve America’s security, environmental quality, and economic prosperity through public-private partnerships that bring reliable and affordable solar energy technologies to the marketplace,” through a variety of educational and business assistance programs. Further, technical innovations planned for the MARET facility and its applied research activities will advance the Solar Program strategic goals to “reduce the cost of solar energy to the point it becomes competitive in relevant energy markets (e.g., buildings, power plants) and for solar technology to enable a sustainable solar industry.” Overarching Goals relative to program needs, future expansion, flexibility, quality of materials, and construction and operational costs:; Experimental: The structure and systems of the building operate as an educational resource. The systems are meant to be a source for data collection and study for building users and instructors; Educational: Part of the evolution of this building and its ongoing goals is to use the building as an

The role of non-technical skills in surgery

Directory of Open Access Journals (Sweden)

Riaz A. Agha

2015-12-01

This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care.

Targeting sediment management strategies using sediment quantification and fingerprinting methods

Science.gov (United States)

Sherriff, Sophie; Rowan, John; Fenton, Owen; Jordan, Phil; hUallacháin, Daire Ó.

2016-04-01

Cost-effective sediment management is required to reduce excessive delivery of fine sediment due to intensive land uses such as agriculture, resulting in the degradation of aquatic ecosystems. Prioritising measures to mitigate dominant sediment sources is, however, challenging, as sediment loss risk is spatially and temporally variable between and within catchments. Fluctuations in sediment supply from potential sources result from variations in land uses resulting in increased erodibility where ground cover is low (e.g., cultivated, poached and compacted soils), and physical catchment characteristics controlling hydrological connectivity and transport pathways (surface and/or sub-surface). Sediment fingerprinting is an evidence-based management tool to identify sources of in-stream sediments at the catchment scale. Potential sediment sources are related to a river sediment sample, comprising a mixture of source sediments, using natural physico-chemical characteristics (or 'tracers'), and contributions are statistically un-mixed. Suspended sediment data were collected over two years at the outlet of three intensive agricultural catchments (approximately 10 km2) in Ireland. Dominant catchment characteristics were grassland on poorly-drained soils, arable on well-drained soils and arable on moderately-drained soils. High-resolution (10-min) calibrated turbidity-based suspended sediment and discharge data were combined to quantify yield. In-stream sediment samples (for fingerprinting analysis) were collected at six to twelve week intervals, using time-integrated sediment samplers. Potential sources, including stream channel banks, ditches, arable and grassland field topsoils, damaged road verges and tracks were sampled, oven-dried (account for particle size and organic matter selectivity processes. Contributions from potential sources type groups (channel - ditches and stream banks, roads - road verges and tracks, fields - grassland and arable topsoils) were

Final report on the sampling and analysis of sediment cores from the L-Area oil and chemical basin

Energy Technology Data Exchange (ETDEWEB)

1985-08-01

Nine vibracores were collected in the L-Area oil and chemical basin (904-83G) during late March and early April 1985. These cores were collected for analysis of the sludge on the basin floor and the underlying sediment. Several different field and laboratory analyses were performed on each three inch segment of all the cores. These included: (1) Sediment characterization; (2) Percent moisture; (3) Dry weight; (4) Spectral gamma analysis; (5) Gross alpha and beta analysis. Detailed chemical analysis were measured on selected intervals of 2 cores (LBC-5 and 6) for complete chemical characterization of the sediments. This sampling program was conducted to provide information so that a closure plan for the basin could be developed. This report describes the methods employed during the project and provide a hard copy of the analytical results from the sample analyses. Included in the appendices are copies of all field and laboratory notes taken during the project and copies of the gas chromatograms for the petroleum hydrocarbon analysis. All chemical results were also submitted on a 5-inch floppy disk.

Technical program plan for the transitioning, decommissioning, and final disposition focus area

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

Hundreds of aging nuclear materials processing facilities within the Department of Energy`s (DOE) Weapons Complex are now being shut down and deactivated. These facilities, situated throughout the United States, will require a monumental effort to clean up safely and with minimal environmental insult. Current cleanup technologies tend to be labor intensive and expensive, they produce an unacceptably large volume of waste, and they expose workers to radioactive and other hazardous substances. This document describes an emerging program designed to develop and demonstrate new technical approaches to the decontamination and decommissioning (D&D) program for DOE`s nuclear materials processing facilities. Sponsored by the DOE Office of Technology Development within the Office of Environmental Restoration and Waste Management (EM), the program seeks to integrate the strengths of DOE`s technical, managerial, and systems engineering capabilities with those of industry, universities, and other government agencies. Once developed, these technologies will help to provide US industry with a competitive edge in the worldwide market that exists for improved environmental restoration and D&D services.

Final report of the UMTRA independent technical review of TAC audit programs

International Nuclear Information System (INIS)

1994-10-01

This report details the findings of an Independent Technical Review (ITR) of practices and procedures for the Uranium Mill Tailings Remedial Action (UMTRA) Project audit program. The audit program is conducted by Jacobs Engineering Group Inc., the Technical Assistance Contractor (TAC) for the UMTRA Project. The purpose of the ITR was to ensure that the TAC audit program is effective and is conducted efficiently. The ITR was conducted from May 16-20, 1994. A review team observed audit practices in the field, reviewed the TAC audit program's documentation, and discussed the program with TAC staff and management. The format of this report has been developed around EPA guidelines; they comprise most of the major section headings. Each section begins by identifying the criteria that the TAC program is measured against, then describing the approach used by the ITR team to measure each TAC audit program against the criteria. An assessment of each type of audit is then summarized for each component in the following order: Radiological audit summary; Health and safety audit summary; Environmental audit summary; Quality assurance audit summary

Technical program plan for the transitioning, decommissioning, and final disposition focus area

International Nuclear Information System (INIS)

1994-01-01

Hundreds of aging nuclear materials processing facilities within the Department of Energy's (DOE) Weapons Complex are now being shut down and deactivated. These facilities, situated throughout the United States, will require a monumental effort to clean up safely and with minimal environmental insult. Current cleanup technologies tend to be labor intensive and expensive, they produce an unacceptably large volume of waste, and they expose workers to radioactive and other hazardous substances. This document describes an emerging program designed to develop and demonstrate new technical approaches to the decontamination and decommissioning (D ampersand D) program for DOE's nuclear materials processing facilities. Sponsored by the DOE Office of Technology Development within the Office of Environmental Restoration and Waste Management (EM), the program seeks to integrate the strengths of DOE's technical, managerial, and systems engineering capabilities with those of industry, universities, and other government agencies. Once developed, these technologies will help to provide US industry with a competitive edge in the worldwide market that exists for improved environmental restoration and D ampersand D services

Technical note: False low turbidity readings from optical probes during high suspended-sediment concentrations

OpenAIRE

N. Voichick; D. J. Topping; R. E. Griffiths

2018-01-01

Turbidity, a measure of water clarity, is monitored for a variety of purposes including (1) to help determine whether water is safe to drink, (2) to establish background conditions of lakes and rivers and detect pollution caused by construction projects and stormwater discharge, (3) to study sediment transport in rivers and erosion in catchments, (4) to manage siltation of water reservoirs, and (5) to establish connections with aquatic biological properties, such as primary ...

Sediment acoustic index method for computing continuous suspended-sediment concentrations

Science.gov (United States)

Landers, Mark N.; Straub, Timothy D.; Wood, Molly S.; Domanski, Marian M.

2016-07-11

Suspended-sediment characteristics can be computed using acoustic indices derived from acoustic Doppler velocity meter (ADVM) backscatter data. The sediment acoustic index method applied in these types of studies can be used to more accurately and cost-effectively provide time-series estimates of suspended-sediment concentration and load, which is essential for informed solutions to many sediment-related environmental, engineering, and agricultural concerns. Advantages of this approach over other sediment surrogate methods include: (1) better representation of cross-sectional conditions from large measurement volumes, compared to other surrogate instruments that measure data at a single point; (2) high temporal resolution of collected data; (3) data integrity when biofouling is present; and (4) less rating curve hysteresis compared to streamflow as a surrogate. An additional advantage of this technique is the potential expansion of monitoring suspended-sediment concentrations at sites with existing ADVMs used in streamflow velocity monitoring. This report provides much-needed standard techniques for sediment acoustic index methods to help ensure accurate and comparable documented results.

Characterization of Vadose Zone Sediment: Borehole 299-W23-19[SX -115] in the S-SX Waste Management Area

International Nuclear Information System (INIS)

Serne, R. Jeffrey; Schaef, Herbert T.; Bjornstad, Bruce N.; Lanigan, David C.; Gee, Glendon W.; Lindenmeier, Clark W.; Clayton, Ray E.; Legore, Virginia L.; Orr, Robert D.; O'Hara, Matthew J.; Brown, Christopher F.; Last, George V.; Kutnyakov, Igor V.; Burke, Deborah Sd; Wilson, Teresa C.; Williams, Bruce A.

2001-01-01

The Tank Farm Vadose Zone Project is led by CH2M HILL Hanford Group, Inc. Their goals include defining risks from past and future single-shell tank farm activities, identifying and evaluating the efficacy of interim measures, and collecting geo-technical information and data. The purpose of these activities is to support future decisions made by the U.S. Department of Energy regarding near-term operations, future waste retrieval, and final closure activities for the single-shell tank Waste Management Areas. To help in this effort, CH2M HILL contracted with scientists at Pacific Northwest National Laboratory to analyze sediment samples collected from borehole 299-W23-19. The conclusions reached from this study support specific mechanisms influencing subsurface migration of contaminants. The mechanisms are supported by the distributions of contaminants beneath tank farms. These observations will help DOE and CH2M HILL identify and implement viable remediation and closure activities

Auto consolidated cohesive sediments erosion

International Nuclear Information System (INIS)

Ternat, F.

2007-02-01

Pollutants and suspended matters of a river can accumulate into the sedimentary column. Once deposited, they are submitted to self-weight consolidation processes, ageing and burying, leading to an increase of their erosion resistance. Pollutant fluxes can be related to sedimentary fluxes, determined by threshold laws. In this work, an erosion threshold model is suggested by introducing a cohesion force into the usual force balance. A model of cohesion is developed on the basis of interactions between argillaceous cohesive particles (clays), particularly the Van der Waals force, whose parameterization is ensured by means of granulometry and porosity. Artificial erosion experiments were performed in a recirculating erosion flume with natural cored sediments where critical shear stress measurements were performed. Other analyses provided granulometry and porosity. The results obtained constitute a good database for the literature. The model is then applied to the experimental conditions and gives good agreement with measurements. An example of the accounting for self-weight consolidation processes is finally suggested, before finishing on a Mohr like diagram dedicated to soft cohesive sediment erosion. (author)

Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-01

The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations.

Projects at the Western Environmental Technology Office. Quarterly technical progress report, July 1, 1995--September 30, 1995

International Nuclear Information System (INIS)

1996-01-01

The goal of this project is to demonstrate the technical and economic feasibility of commercializing a biotechnology that uses plants to remediate soils, sediments, surface waters, and groundwaters contaminated by heavy metals and radionuclides. This technology, known as phytoremediation, is particularly suited to remediation of soils or water where low levels of contaminants are widespread. Project objectives are to provide an accurate estimate of the capability and rate of phytoremediation for removal of contaminants of concern from soils and groundwaters at Department of Energy (DOE) sites and to develop data suitable for engineering design and economic feasibility evaluations, including methods for destruction or final disposition of plants containing contaminants of concern. The bioremediation systems being evaluated could be less expensive than soil removal and treatment systems, given the areal extent and topography of sites under consideration and the investment of energy and money in soil-moving and -treating processes. In situ technology may receive regulatory acceptance more easily than ex situ treatments requiring excavation, processing, and replacement of surface soils. In addition, phytoremediation may be viable for cleanup of contaminated waters, either as the primary treatment or the final polishing stage, depending on the contaminant concentrations and process economics considerations

Technical writing versus technical writing

Science.gov (United States)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Technical procedures for utilities and solid waste: Environmental Field Program, Deaf Smith County site, Texas: Final draft

International Nuclear Information System (INIS)

1987-08-01

The evaluation of environmental issues and concerns and the addressing of statutory requirements are fundamental parts in the characterization of the site in Deaf Smith County, Texas for the US Department of Energy's Salt Repository Project (SRP). To ensure that the environmental field program comprehensively addresses the issues and requirements of the project, a site study plan (SSP) has been prepared for Utilities and Solid Waste considerations. This technical procedure (TP) has been developed to implement the field program described in the Utilities and Solid Waste Site Study Plan. The purpose and scope of the Utilities and Solid Waste Technical Procedure is to develop and implement a data collection procedure to fulfill the data base needs of the Utilities and Solid Waste SSP. The procedure describes a method of obtaining, assessing and verifying the capabilities of the regional service utilities and disposal contractors. This data base can be used to identify a preferred service source for the engineering contractor. The technical procedure was produced under the guidelines established in Technical Administrative Procedure No. 1.0, Preparation, Review and Approval of Technical Procedures

Quantifying trail erosion and stream sedimentation with sediment tracers

Science.gov (United States)

Mark S. Riedel

2006-01-01

Abstract--The impacts of forest disturbance and roads on stream sedimentation have been rigorously investigated and documented. While historical research on turbidity and suspended sediments has been thorough, studies of stream bed sedimentation have typically relied on semi-quantitative measures such as embeddedness or marginal pool depth. To directly quantify the...

KBS Technical report 1-120 (1977-1978). Summaries

International Nuclear Information System (INIS)

1979-05-01

The Swedish nuclear utilities started early in 1977 the KBS (nuclear fuel safety) project to study the high level waste problem and report on how and where a safe final storage could be arranged in Sweden. The docummentation produced by the project during 1977 and 1978 has been collected in a series of technical reports numbered from 1 to 120. The English summaries of the technical reports have been collected in this separate volume, No. 121. (G.B.)

Mechanism of Hg(II) Immobilization in Sediments by Sulfate-Cement Amendment.

Science.gov (United States)

Serrano, Susana; Vlassopoulos, Dimitri; O'Day, Peggy A

2016-04-01

Reactive amendments such as Portland and super-sulfate cements offer a promising technology for immobilizing metalloid contaminants such as mercury (Hg) in soils and sediments through sequestration in less bioavailable solid forms. Tidal marsh sediments were reacted with dissolved Hg(II) in synthetic seawater and fresh water solutions, treated with Portland cement and FeSO 4 amendment, and aged for up to 90 days. Reacted solids were analyzed with bulk sequential extraction methods and characterized by powder X-ray diffraction (XRD), electron microscopy, and synchrotron X-ray absorption spectroscopy at the Hg L III - and S K-edge. In amended sediments, XRD, SEM and sulfur K-edge XANES indicated formation of gypsum in seawater experiments or ettringite-type (Ca 6 Al 2 (SO 4 ) 3 (OH) 12 . 26H 2 O) phases in fresh water experiments, depending on the final solution pH (seawater ∼8.5; freshwater ∼10.5). Analysis of Hg EXAFS spectra showed Cl and Hg ligands in the first- and second-coordination shells at distances characteristic of a polynuclear chloromercury(II) salt, perhaps as a nanoparticulate phase, in both seawater and fresh water experiments. In addition to the chloromercury species, a smaller fraction (∼20-25%) of Hg was bonded to O atoms in fresh water sample spectra, suggesting the presence of a minor sorbed Hg fraction. In the absence of amendment treatment, Hg sorption and resistance to extraction can be accounted for by relatively strong binding by reduced S species present in the marsh sediment detected by S XANES. Thermodynamic calculations predict stable aqueous Hg-Cl species at seawater final pH, but higher final pH in fresh water favors aqueous Hg-hydroxide species. The difference in Hg coordination between aqueous and solid phases suggests that the initial Hg-Cl coordination was stabilized in the cement hydration products and did not re-equilibrate with the bulk solution with aging. Collectively, results suggest physical encapsulation of Hg as a

Specified radioactive waste final disposal act

International Nuclear Information System (INIS)

Yasui, Masaya

2001-01-01

Radioactive wastes must be finally and safely disposed far from human activities. Disposal act is a long-range task and needs to be understood and accepted by public for site selection. This paper explains basic policy of Japanese Government for final disposal act of specified radioactive wastes, examination for site selection guidelines to promote residential understanding, general concept of multi-barrier system for isolating the specific radioactive wastes, and research and technical development for radioactive waste management. (S. Ohno)

The assessment of sediment screening risk in Venice Lagoon and other coastal areas using international sediment quality guidelines

International Nuclear Information System (INIS)

Apitz, S.A.; Barbanti, A.; Bocci, M.; Delaney, E.; Bernstein, A.G.; Montobbio, L.

2007-01-01

A number of studies carried out in recent years have shown the presence of a wide range of contaminants in the Venice Lagoon. It is important to have a good understanding of the ecological quality of Venice Lagoon sediments, in order to: i) define and locate areas where a threat to the environment is present and therefore an intervention is needed (i.e. in situ assessment and management); and ii) define sustainable and environmentally correct ways of managing sediments which are to be dredged for navigational purposes or in relation to other interventions (i.e., ex situ management). Materials and Methods: To examine how various regional and international SQGs 'classed' screening risk in Venice Lagoon sediments, data on median contaminant levels in surface sediments in Venice Lagoon resulting from a literature review were compared to a range of local and international sediment quality guidelines (SQGs). Then data on sediment contaminant levels in various areas and sub-basins of Venice Lagoon (main Lagoon, Porto Marghera and Venice City Canals) and in other regional and international transitional and coastal ecosystems with various levels of human impact (urbanization and industrialization) were evaluated based upon a selected consensus-based SQG. Finally, screening sediment quality for all of Venice Lagoon was mapped and contoured, relative to this consensus-based SQG and briefly compared with direct toxicity measurement through a battery of bioassays. Results: SQGs allow the sediment areas to be put in terms of potential, or screening, risk. Although there were some differences depending upon which specific SQGs were applied, the Venice SQGs and other international SQGs provided the same general picture of screening risk in Venice Lagoon despite geographic differences. Venice Lagoon South has the lowest screening risk levels, Venice Lagoon Central/North has the highest (and is nearest to the Porto Marghera and Venice City Canals sites). Discussion: The Venice

Final report - Microbial pathways for the reduction of mercury in saturated subsurface sediments

Energy Technology Data Exchange (ETDEWEB)

Tamar barkay; Lily Young; Gerben Zylstra

2009-08-25

Mercury is a component of mixed wastes that have contaminated vast areas of the deep subsurface as a result of nuclear weapon and energy production. While this mercury is mostly bound to soil constituents episodes of groundwater contamination are known in some cases resulting in potable water super saturated with Hg(0). Microbial processes that reduce Hg(II) to the elemental form Hg(0) in the saturated subsurface sediments may contribute to this problem. When we started the project, only one microbial pathway for the reduction of Hg(II), the one mediated by the mer operon in mercury resistant bacteria was known. As we had previously demonstrated that the mer mediated process occurred in highly contaminated environments (Schaefer et al., 2004), and mercury concentrations in the subsurface were reported to be low (Krabbenhoft and Babiarz, 1992), we hypothesized that other microbial processes might be active in reducing Hg(II) to Hg(0) in saturated subsurface environments. The specific goals of our projects were: (1) Investigating the potential for Hg(II) reduction under varying electron accepting conditions in subsurface sediments and relating these potential to mer gene distribution; and (2) Examining the physiological and biochemical characteristics of the interactions of anaerobic bacteria with mercury. The results are briefly summarized with references to published papers and manuscripts in preparation where details about our research can be found. Additional information may be found in copies of our published manuscripts and conference proceedings, and our yearly reports that were submitted through the RIMS system.

A Study on the Environmental Standard of Sediment on the Bottom of the Water

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Hee; Yoo, Hye Jin [Korea Environment Institute, Seoul (Korea)

2000-12-01

Sediment on the bottom of the water has been considered one of the water pollutants in the environmental management of Korea so treated as a management on pollutants, as you can see the examples in the dragging operation in the polluted sea area. To healthily maintain and conserve the water ecosystem including bottom living things in the water, sediment on the bottom of the water should be recognized as the independent medium, which should maintain the certain quality like the water, the atmosphere, and soil, rather than the source of water pollution. Such recognition means that the management of sediment on the bottom of the water should change the fragmentary goal, centered the post management focusing on the water management, to the ecosystematic goal including the bottom living things. In a point of the view, this study has a great significance to suggest not only the final goal for the management of sediment on the bottom of the water but also the necessity of developing the environmental standard of the sediment on the bottom of the water, which is a standard of the management or judgment in the actual managing the sediment on the bottom of the water - an estimation on the pollution of sediment, a removal of the polluted sediment, a purification of sediment, and an abandonment of the dragged sediment -, and the development measures. Considering the situation that even the basic scheme related to the management of sediment is not prepared in the Government level, the concept of the environmental standard of sediment, the foreign example of the environmental standard of sediment, the current state of the domestic sediment pollution, and the development scheme of the environmental standard in this study must be the important foundation to establish the management system of sediment in the Government level. 121 refs., 10 figs., 45 tabs.

Dissemination of Continuing Education Materials Via Television Delivery Systems. Final Technical Report and Final Report.

Science.gov (United States)

Munushian, Jack

In 1972, the University of Southern California School of Engineering established a 4-channel interactive instructional television network. It was designed to allow employees of participating industries to take regular university science and engineering courses and special continuing education courses at or near their work locations. Final progress…

Final Scientific/Technical Report from Hofstra University on DE-SC0001985

Energy Technology Data Exchange (ETDEWEB)

Farmer, E. Christa [Hofstra Univ., Hempstead, NY (United States)

2016-12-20

The U.S. Department of Energy award DE-SC0001985 funded the Hofstra University Center for Climate Study (HUCCS) from 29 September 2009 through 1 October 2016. This support enabled several activities over the period of the grant, including 1) the pursuit of several research projects, including sediment coring of coastal marshes, analysis of habitat impact due to climate change, and effects of raindrops of CO2 transfer; 2) support for multiple graduate and undergraduate students, and sponsorship of research projects that involved high school students; 3) fostering mentoring relationships and networking; 4) the design, creation, and installation of an exhibit on climate change at the Cradle of Aviation Museum in Garden City, NY as an effort of public outreach. A total of 11 presentations at conferences, one book, and one peer-reviewed journal article resulted from these activities.

Nagra technical report 14-02, geological basics - Dossier I - Introduction and summary

International Nuclear Information System (INIS)

Gautschi, A.; Zuidema, P.

2014-01-01

This dossier is the first of a series of eight reports concerning the safety and technical aspects of locations for the disposal of radioactive wastes in Switzerland. It presents an introduction to and a summary of the further seven dossiers on basic geological conditions. Dossier II considers the sediments that can be used along with tectonic considerations, Dossier III takes a look at long-term geological developments and Dossier IV considers the geo-mechanical documentation available. Dossier V looks at hydro-geological considerations. Dossier VI reports on the barrier properties of the proposed host rock sediments and neighbouring rock layers. Dossiers VII takes a look at usage conflicts and Dossier VIII considers the possibilities for the characterisation of the substrates and for the ways in which they can be explored

Climate vs. tectonic induced variations in Cenozoic sediment supply from western Scandinavia

DEFF Research Database (Denmark)

Gołędowski, Bartosz; Nielsen, S.B.; Clausen, O.R.

Eocene times tectonic activity related to the final stage of opening of the North Atlantic was apparently controlling the sediment input in the North Sea as sediment pulses correlate well with tectonic events. Although there is no signs of Cenozoic tectonic activity onshore Scandinavia (igneous bodies......, faulting), tectonic disturbance related to ocean opening could be responsible for deposition of thick Paleocene wedges along the western coast of Norway. During subsequent Cenozoic periods domal structures in the Norwegian shelf are a proof for mild and protracted compression. However, depositional...... patterns from offshore Scandinavia have been interpreted as a result of significant tectonic movements. In the absence of proofs for active tectonic agents we attempt to explain these sediment input variations as a result of climate fluctuations. The Eocene-Oligocene greenhouse-icehouse climate transition...

Sediment Transport

DEFF Research Database (Denmark)

Liu, Zhou

Flow and sediment transport are important in relation to several engineering topics, e.g. erosion around structures, backfilling of dredged channels and nearshore morphological change. The purpose of the present book is to describe both the basic hydrodynamics and the basic sediment transport...... mechanics. Chapter 1 deals with fundamentals in fluid mechanics with emphasis on bed shear stress by currents, while chapter 3 discusses wave boundary layer theory. They are both written with a view to sediment transport. Sediment transport in rivers, cross-shore and longshore are dealt with in chapters 2......, 4 and 5, respectively. It is not the intention of the book to give a broad review of the literature on this very wide topic. The book tries to pick up information which is of engineering importance. An obstacle to the study of sedimentation is the scale effect in model tests. Whenever small...

Effects of fine suspended sediment releases on benthic communities in artificial flumes

International Nuclear Information System (INIS)

Bruno, Maria Cristina; Carolli, Mauro; Zolezzi, Guido; Palmia, Beatrice

2016-01-01

The Italian Alps feed a large number of reservoirs for hydropower production, which are losing storage capacity due to natural inflow of sediment of different origin (alluvial, glacial). Local government and local environmental agencies authorize periodical sediment flushes with a mandatory release regime when such measure is technically feasible. Management of reservoirs often includes fine sediment pulses, which cause several ecological impacts on downstream water bodies. We conducted a set of simulations in five semi artificial flumes naturally fed by an un-impacted Alpine stream (Trentino region, NE Italy), to: i) identify possible thresholds of concentration of fine suspended sediment inducing drift in the benthic community and, ii) assess the dynamics and intensity of the drift responses in the dominant taxa. The results can help to identify the least impacting release management practices. Sediment pulses were simulated by adding fine material of known concentration to the upstream end of the flumes. The benthic organisms drifting from the whole flume were collected by filtering the whole outflow for consecutive short time intervals. We tested four different concentration values, i.e. 10x,100x, 250x, 500x the base concentration of 4 NTU, and we repeated the simulations in two periods: July, when the community is composed mainly of young larval instars and the sediment wave lasted 10 minutes, and October, when later larval stages are dominant and the wave lasted 20 minutes. In July, the maximum concentration induced a significantly higher drift response than the three lower ones. In October, even if the sediment wave was twice as long as July one, drift responses where lower, and only the responses to the highest and lowest concentrations differed significantly. In our simulation, the only possible cause for the observed increase in drift was the sediment in the suspended phase, as the deposition of sediment was negligible, and discharge did not increase

Dating of sediments and determination of sedimentation rate. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Illus, E [ed.

1998-08-01

The Second NKS (Nordic Nuclear Safety Research)/EKO-1 Seminar was held at the Finnish Centre for Radiation and Nuclear Safety (STUK) on April 2-3, 1997. The work of the NKS is based on 4-year programmes; the current programme having been planned for the years 1994-1997. The programme comprises 3 major fields, one of them being environmental effects (EKO). Under this umbrella there are 4 main projects. The EKO-1 project deals with marine radioecology, in particular bottom sediments and sediment processes. The programme of the second seminar consisted of 8 invited lecturers and 6 other scientific presentations. Dating of sediments and determination of sedimentation rate are important in all types of sedimentological study and model calculations of fluxes of substances in the aquatic environment. In many cases these tasks have been closely related to radioecological studies undertaken in marine and fresh water environments, because they are often based on measured depth profiles of certain natural or artificial radionuclides present in the sediments. During recent decades Pb-210 has proved to be very useful in dating of sediments, but some other radionuclides have also been successfully used, e.g. Pu-239,240, Am-241 and Cs-137. The difficulties existing and problems involved in dating of sediments, as well as solutions for resolving these problems are discussed in the presentations

Dating of sediments and determination of sedimentation rate. Proceedings

International Nuclear Information System (INIS)

Illus, E.

1998-01-01

The Second NKS (Nordic Nuclear Safety Research)/EKO-1 Seminar was held at the Finnish Centre for Radiation and Nuclear Safety (STUK) on April 2-3, 1997. The work of the NKS is based on 4-year programmes; the current programme having been planned for the years 1994-1997. The programme comprises 3 major fields, one of them being environmental effects (EKO). Under this umbrella there are 4 main projects. The EKO-1 project deals with marine radioecology, in particular bottom sediments and sediment processes. The programme of the second seminar consisted of 8 invited lecturers and 6 other scientific presentations. Dating of sediments and determination of sedimentation rate are important in all types of sedimentological study and model calculations of fluxes of substances in the aquatic environment. In many cases these tasks have been closely related to radioecological studies undertaken in marine and fresh water environments, because they are often based on measured depth profiles of certain natural or artificial radionuclides present in the sediments. During recent decades Pb-210 has proved to be very useful in dating of sediments, but some other radionuclides have also been successfully used, e.g. Pu-239,240, Am-241 and Cs-137. The difficulties existing and problems involved in dating of sediments, as well as solutions for resolving these problems are discussed in the presentations

Hawaii Regional Sediment Management (RSM): Regional Sediment Budget for the West Maui Region

Science.gov (United States)

2016-06-01

ER D C/ CH L TR -1 6- 5 Regional Sediment Management (RSM) Program Hawaii Regional Sediment Management (RSM): Regional Sediment Budget...acwc.sdp.sirsi.net/client/default. Regional Sediment Management (RSM) Program ERDC/CHL TR-16-5 June 2016 Hawaii Regional Sediment Management...distribution is unlimited. Prepared for U.S. Army Corps of Engineers Washington, DC 20314-1000 Under Project 454632, “ Hawaii Regional Sediment Management

Electricity generation by anaerobic bacteria and anoxic sediments from hypersaline soda lakes

Science.gov (United States)

Miller, L.G.; Oremland, R.S.

2008-01-01

Anaerobic bacteria and anoxic sediments from soda lakes produced electricity in microbial fuel cells (MFCs). No electricity was generated in the absence of bacterial metabolism. Arsenate respiring bacteria isolated from moderately hypersaline Mono Lake (Bacillus selenitireducens), and salt-saturated Searles Lake, CA (strain SLAS-1) oxidized lactate using arsenate as the electron acceptor. However, these cultures grew equally well without added arsenate using the MFC anode as their electron acceptor, and in the process oxidized lactate more efficiently. The decrease in electricity generation by consumption of added alternative electron acceptors (i.e. arsenate) which competed with the anode for available electrons proved to be a useful indicator of microbial activity and hence life in the fuel cells. Shaken sediment slurries from these two lakes also generated electricity, with or without added lactate. Hydrogen added to sediment slurries was consumed but did not stimulate electricity production. Finally, electricity was generated in statically incubated "intact" sediment cores from these lakes. More power was produced in sediment from Mono Lake than from Searles Lake, however microbial fuel cells could detect low levels of metabolism operating under moderate and extreme conditions of salt stress. ?? 2008 US Government.

Assessment of technical risks and R and D requirements for a magnetic confinement fusion fuel system. Final report

International Nuclear Information System (INIS)

DeFreece, D.A.

1983-11-01

This report documents a specific use and results of a novel technique for assessing the technical risks associated with the hardware development of a possible future commercial fusion power plant fuel system. Technical risk is defined as the risk that a particular technology or component which is currently under development will not achieve a set of required technical specifications. A technical risk assessment is the quantification of this risk. This Technical Risk Assessment (TRA) methodology was applied to a deuterium-tritium fuel system for a magnetic-confinement fusion power plant. The fuel system is defined to support a generic commercial reactor with at least two viable options for each critical subsystem. Each subsystem option is defined in detail including nominal performance requirements and subsystem interfaces. Subsystem experts were canvassed to obtain values for past, present and future technical performance parameters for each of the subsystem options. These forecasts are presented as probabilities of achieving given levels of performance in specific time periods for assumed funding scenarios. Several funding scenarios were examined to discern whether performance limitations are caused by funding or technology. A computerized Fuel System simulation is described which uses these subsystem performance parameter forecasts as inputs

Data quality objectives summary report for 105-N Basin sediment disposition

International Nuclear Information System (INIS)

Pisarcik, D.J.

1998-01-01

During stabilization of the 105-N Basin, sediments that have accumulated on 105-N Basin surfaces will be vacuumed, collected in the North Cask Pit of the basin complex, and eventually removed. The Environmental Assessment for the Deactivation of the N Reactor Facilities describes two potential disposition paths for the 105-N Basin sediment: transfer in slurry form to a double-shell tank if determined to be a transuranic waste, or disposal in solid form as a low-level waste. Interim storage of the sediments may be required if a transfer to the Tank Waste Remediation System cannot meet schedule milestones. Selection of a particular alternative depends on the final characterization of the accumulated sediment, regulatory requirements, cost/benefit analyses, and 105-N Stabilization Project schedule requirements. Revision 0 of this Data Quality Objectives (DQO) report was issued to describe a formal DQO process that was performed according to BHI-EE-01, Environmental Investigations Procedures, EIP 1.2, Data Quality Objectives, Revision 1. Since publication of Revision 0 of this report, important changes to the disposition strategy for 100-N Deactivation sediment material have been proposed, evaluated, discussed with the US Department of Energy and State of Washington Department of Ecology, and implemented. Revision 1 of this report documents these changes

Final disposal of radioactive wastes. Site selection criteria. Technical and economical factors

International Nuclear Information System (INIS)

Granero, J.J.

1984-01-01

General considerations, geological and socioeconomical criteria for final disposal of radioactive wastes in geological formations are treated. More attention is given to the final disposal of high level radioactive wastes and different solutions searched abroad which seems of interest for Spain. (author)

Santa Barbara Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hacker, Angela; Hansen, Sherman; Watkins, Ashley

2013-11-30

This report serves as the Final Report for Santa Barbara County’s Energy Efficiency and Conservation Block Grant (EECBG) BetterBuildings Neighborhood Program (BBNP) award from the U.S. Department of Energy (DOE). This report explains how DOE BBNP funding was invested to develop robust program infrastructure designed to help property owners complete energy improvements, thereby generating substantial outcomes for the local environment and economy. It provides an overview of program development and design within the grant period, program accomplishments and challenges to date, and a plan for the future sustainability of emPower, the County’s innovative clean energy and building efficiency program. During the grant period, Santa Barbara County’s emPower program primarily targeted 32,000 owner occupied, single family, detached residential homes over 25 years old within the County. In order to help these homeowners and their contractors overcome market barriers to completing residential energy improvements, the program developed and promoted six voluntary, market-based service areas: 1) low cost residential financing (loan loss reserve with two local credit unions), 2) residential rebates, 3) local customer service, 4) expert energy advising, 5) workforce development and training, and 6) marketing, education and outreach. The main goals of the program were to lower building energy use, create jobs and develop a lasting regional building performance market. These services have generated important early outcomes and lessons after the program’s first two years in service. The DOE BBNP funding was extended through October 2014 to enable Santa Barbara County to generate continued outcomes. In fact, funding related to residential financing remains wholly available for the foreseeable future to continue offering Home Upgrade Loans to approximately 1,300 homeowners. The County’s investment of DOE BBNP funding was used to build a lasting, effective, and innovative

Upstream sediment input effects on experimental dune trough scour in sediment mixtures

NARCIS (Netherlands)

Kleinhans, M.G.

2005-01-01

Understanding causes of dune irregularity, especially dune trough scour, is important for the modeling of vertical sorting of sediment mixtures in morphological models of rivers with sediment mixtures. Sediment in dunes is generally sorted in a fining-upward manner, which affects the sediment

77 FR 42637 - Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments; Corrections

Science.gov (United States)

2012-07-20

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Parts 84 and 115 [Docket No. USCG-2012-0306] RIN 1625-AB86 Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments...), the Coast Guard published a final rule entitled ``Navigation and Navigable Waters; Technical...

Evaluation of effects of phenol recovery on biooxidation and tertiary treatment of SRC-I wastewater. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Mitchell, J.W.; Watt, J.C.; Cowan, W.F.; Schuyler, S.E.

1983-09-01

Addition of phenol recovery to the wastewater treatment scheme in the Baseline Design for the SRC-I Demonstration Plant was evaluated as a major post-Baseline effort. Phenol recovery affects many downstream processes, but this study was designed to assess primarily its effects on biooxidation and subsequent tertiary treatment. Two parallel treatment schemes were set up, one to treat dephenolated wastewaters and the other for processed nondephenolated wastewaters, a simulation of the Baseline Design. The study focused on comparisons of five areas: effluent quality; system stability; the need for continuous, high-dose powdered activated carbon (PAC) augmentation to the bioreactor; minimum bioreactor hydraulic residence time (HRT); and tertiary treatment requirements. The results show that phenol recovery improves the quality of the bioreactor effluent in terms of residual organics and color. With phenol recovery, PAC augmentation is not required; without phenol recovery, PAC is needed to produce a comparable effluent. Dephenolization also enhances the stability of biooxidation, and reduces the minimum HRT required. With tertiary treatment, both schemes can meet the effluent concentrations published in the SRC-I Final Envivornmental Impact Statement, as well as the anticipated effluent limits. However, phenol recovery does provide a wider safety margin and could eliminate the need for some of the tertiary treatment steps. Based solely on the technical merits observed in this study, phenol recovery is recommended. The final selection should, however, also consider economic tradeoffs and results of other studies such as toxicology testing of the effluents. 34 references, 30 figures and 26 tables.

Chemistry of marine sediments

International Nuclear Information System (INIS)

Yen, T.F.

1977-01-01

Some topics considered are as follows: characterization of sediments in the vicinity of offshore petroleum production; thermal alteration experiments on organic matter in recent marine sediments as a model for petroleum genesis; composition of polluted bottom sediments in Great Lakes harbors; distribution of heavy metals in sediment fractions; recent deposition of lead off the coast of southern California; release of trace constituents from sediments resuspended during dredging operations; and migration of chemical constituents in sediment-seawater interfaces

Final Technical Report for Quantum Embedding for Correlated Electronic Structure in Large Systems and the Condensed Phase

Energy Technology Data Exchange (ETDEWEB)

Chan, Garnet Kin-Lic [Princeton Univ., NJ (United States)

2017-04-30

This is the final technical report. We briefly describe some selected results below. Developments in density matrix embedding. DMET is a quantum embedding theory that we introduced at the beginning of the last funding period, around 2012-2013. Since the first DMET papers, which demonstrated proof-of- principle calculations on the Hubbard model and hydrogen rings, we have carried out a number of different developments, including: Extending the DMET technology to compute broken symmetry phases, including magnetic phases and super- conductivity (Pub. 13); Calibrating the accuracy of DMET and its cluster size convergence against other methods, and formulation of a dynamical cluster analog (Pubs. 4, 10) (see Fig. 1); Implementing DMET for ab-initio molecular calculations, and exploring different self-consistency criteria (Pubs. 9, 14); Using embedding to defi ne quantum classical interfaces Pub. 2; Formulating DMET for spectral functions (Pub. 7) (see Fig. 1); Extending DMET to coupled fermion-boson problems (Pub. 12). Together with these embedding developments, we have also implemented a wide variety of impurity solvers within our DMET framework, including DMRG (Pub. 3), AFQMC (Pub. 10), and coupled cluster theory (CC) (Pub. 9).

Scientific-technical cooperation with foreign (esp. Europe and INSC partner countries) nuclear regulatory authorities and their technical support organizations in the fields of nuclear safety of operating nuclear power plants and on the concept evaluation of generation 3+ plants. Final report

International Nuclear Information System (INIS)

Wolff, Holger

2016-09-01

The BMUB/BfS-Project 3614I01512 forms the frame of the GRS for the scientific-technical cooperation with Technical Support Organisations and Nuclear Regulatory Authorities in the field of nuclear safety in operating NPPs and for the concept evaluation of generation 3 + plants in Europe and INSC Partner Countries. In the present final project report results are described which were gained within the project duration 15.10.2014 up to the 30.09.2016 in the following working packages: Investigations following the catastrophe of Fukushima Daiichi, Evaluation of selected National Action Plans, DBA and severe accident analyses for NPP with PWR (WWER-440, WWER-1000), cooperation with INSC partner countries on DBA, BDBA and severe accident analyses for WWER plants of generation 3 + and building NRA and safety evaluation capacities and decommissioning of nuclear facilities and disposal of radioactive waste. The results are preceded by an outline on the activities related to the project management and to the planning of the bilateral work.

Metal complexation capacity of Antarctic lacustrine sediments.

Science.gov (United States)

Alberti, Giancarla; Mussi, Matteo; Quattrini, Federico; Pesavento, Maria; Biesuz, Raffaela

2018-04-01

The purpose of this study is to implement a work that is a part of a project funded by the Italian National Antarctic Research Program (PNRA, Piano Nazionale di Ricerche in Antartide) within the main thematic focus "Chemical Contamination-Global Change". This research was devoted to detect and characterize micro and nano components with strong complexing capability towards metal ions at trace level in sea water, lakes and lacustrine sediments, sampled during the XXII expedition of PNRA. In particular, in the present work, the sorption complexation capacity of an Antarctic lacustrine sediments toward Cu(II) and Pb(II) is described. The characterization of the sorption was undertaken, studying kinetics and isotherm profiles. The lake here considered is Tarn Flat in the area of Terra Nova Bay. The sorption equilibria of Cu(II) and Pb(II) on the lacustrine sediments were reached in about 10 h, and they were best modelled by the Langmuir equation. Preliminary, to establish if the data here obtained were consistent with those reported for the same area in other expeditions, a common multivariate techniques, namely the principal component analysis (PCA), was applied and finally the consistency of the data has been confirmed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Remote Sensing of Suspended Sediment Dynamics in the Mississippi Sound

Science.gov (United States)

Merritt, D. N.; Skarke, A. D.; Silwal, S.; Dash, P.

2016-02-01

The Mississippi Sound is a semi-enclosed estuary between the coast of Mississippi and a chain of offshore barrier islands with relatively shallow water depths and high marine biodiversity that is wildly utilized for commercial fishing and public recreation. The discharge of sediment-laden rivers into the Mississippi Sound and the adjacent Northern Gulf of Mexico creates turbid plumes that can extend hundreds of square kilometers along the coast and persist for multiple days. The concentration of suspended sediment in these coastal waters is an important parameter in the calculation of regional sediment budgets as well as analysis of water-quality factors such as primary productivity, nutrient dynamics, and the transport of pollutants as well as pathogens. The spectral resolution, sampling frequency, and regional scale spatial domain associated with satellite based sensors makes remote sensing an ideal tool to monitor suspended sediment dynamics in the Northern Gulf of Mexico. Accordingly, the presented research evaluates the validity of published models that relate remote sensing reflectance with suspended sediment concentrations (SSC), for similar environmental settings, with 51 in situ observations of SSC from the Mississippi Sound. Additionally, regression analysis is used to correlate additional in situ observations of SSC in Mississippi Sound with coincident observations of visible and near-infrared band reflectance collected by the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor aboard the Aqua satellite, in order to develop a site-specific empirical predictive model for SSC. Finally, specific parameters of the sampled suspended sediment such as grain size and mineralogy are analyzed in order to quantify their respective contributions to total remotely sensed reflectance.

TCR as supervisor of technical systems

CERN Document Server

Laeger, H

1998-01-01

Our Technical Control Room (TCR) provides continuous supervision of CERN's technical infrastructure. It also serves the inhabitants of CERN's premises as a contact point in case of problems. Every year we initiate eleven thousand recorded corrective interventions; about half subsequent to user phone calls, the other half to automatic alarms. TCR tasks are essentially fourfold: collect and distribute information on abnormal operation states; supervise those technical systems for which we have a mandate; initiate corrective interventions; and perform corrective on-site interventions outside normal working hours. A TCR operator normally has an education corresponding to a French BTS and initially little professional experience. He holds short-term contracts, up to a maximum of six years. This paper outlines TCR tasks and presents some statistical data. It also indicates relations between users, equipment groups, contract firms and the TCR as go-between. Finally, it gives an account of our seven years experience ...

Modular Electric Vehicle Program (MEVP). Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The Modular Electric Vehicle Program (MEVP) was an EV propulsion system development program in which the technical effort was contracted by DOE to Ford Motor Company. The General Electric Company was a major subcontractor to Ford for the development of the electric subsystem. Sundstrand Power Systems was also a subcontractor to Ford, providing a modified gas turbine engine APU for emissions and performance testing as well as a preliminary design and producibility study for a Gas Turbine-APU for potential use in hybrid/electric vehicles. The four-year research and development effort was cost-shared between Ford, General Electric, Sundstrand Power Systems and DOE. The contract was awarded in response to Ford`s unsolicited proposal. The program objective was to bring electric vehicle propulsion system technology closer to commercialization by developing subsystem components which can be produced from a common design and accommodate a wide range of vehicles; i.e., modularize the components. This concept would enable industry to introduce electric vehicles into the marketplace sooner than would be accomplished via traditional designs in that the economies of mass production could be realized across a spectrum of product offerings. This would eliminate the need to dedicate the design and capital investment to a limited volume product offering which would increase consumer cost and/or lengthen the time required to realize a return on the investment.

Technical bid evaluation

International Nuclear Information System (INIS)

Bruchhausen, E. v.

1975-01-01

It is shown which kind of problems arise for the owners of the project and what is the recommendable method of approach. A detailed description of the necessary working team, information in delegation of work and tasks of procedure, criteria of valuation and classification method. Examples of schemes are shown which are the basis of the technical bid evaluation: tables 'data of system/component' and 'scope of supply'. The procedure of normalization of the bids and of specifying the owners supplies are explained. The content of the final report is described. (HP) [de

Job and task analysis for technical staff

International Nuclear Information System (INIS)

Toline, B.C.

1991-01-01

In September of 1989 Cooper Nuclear Station began a project to upgrade the Technical Staff Training Program. This project's roots began by performing job and Task Analysis for Technical Staff. While the industry has long been committed to Job and Task Analysis to target performance based instruction for single job positions, this approach was unique in that it was not originally considered appropriate for a group as diverse as Tech Staff. Much to his satisfaction the Job and Task Analysis Project was much less complicated for Technical Staff than the author had imagined. The benefits of performing the Job and Task Analysis for Technical Staff have become increasingly obvious as he pursues lesson plan development and course revisions. The outline for this presentation will be as follows: philosophy adopted; preparation of the job survey document; performing the job analysis; performing task analysis for technical staff and associated pitfalls; clustering objectives for training and comparison to existing program; benefits now and in the future; final phase (comparison to INPO guides and meeting the needs of non-degreed engineering professionals); and conclusion. By focusing on performance based needs for engineers rather than traditional academics for training the author is confident the future Technical Staff Program will meet the challenges ahead and will exceed requirements for accreditation

Evaluation of suspended sediment concentrations, sediment fluxes and sediment depositions along a reservoir by using laser diffraction and acoustic backscatter data

Science.gov (United States)

Lizano, Laura; Haun, Stefan

2015-04-01

The construction of dams and reservoirs disturb the natural morphological behavior of rivers. A natural settling effect occurs due to the reduced turbulences and flow velocities. As a consequence, reservoirs fill up with sediments which results in a reduction of storage volume, influences the operation of hydropower plants and leads in several cases to flood protection problems. The sediment depositions in reservoirs are standardly evaluated by using bathymetric data, obtained by a single beam sonar from pre-defined cross sections or by an extensive evaluation of the reservoir bed by a side scan sonar. However, a disadvantage of this method is that it is not possible to evaluate the pore water content of the depositions, which may lead as consequence to an uncertainty in the measured amount of deposited sediments. Given that a major part of sediments entering reservoirs are transported in suspension, sediment flux measurements along defined transects could give more reliable information on the settled amount of sediments and additional information on the sediment transport mechanism within the reservoir. An evaluation of the sediment fluxes is in practice often conducted by a single suspended sediment concentration (SSC) measurement in combination with a cross sectional calibration factor to take changes in the SSC along the transect into account. However, these calibration factors are often developed only for one specific in-situ condition and may give unreliable results in case that the boundaries change e.g. the hydraulic conditions. Hence an evaluation of the sediment fluxes along the whole transect would give a more reliable number for the amount of transported sediments through the reservoir. This information can afterwards be used to calculate the amount of settled sediments in different sections of the reservoir and the amount of sediments which will enter the intake. For this study the suspended sediment transport within the Peñas Blancas reservoir in

Final Technical Report for DE-SC0012297

Energy Technology Data Exchange (ETDEWEB)

Dell' Antonio, Ian [Brown Univ., Providence, RI (United States)

2017-08-01

This is the final report on the work performed in award DE-SC0012297, Cosmic Frontier work in support of the LSST Dark Energy Science Collaboration's work to develop algorithms, simulations, and statistical tests to ensure optimal extraction of the dark energy properties from galaxy clusters observed with LSST. This work focused on effects that could produce a systematic error on the measurement of cluster masses (that will be used to probe the effects of dark energy on the growth of structure). These effects stem from the deviations from pure ellipticity of the gravitational lensing signal and from the blending of light of neighboring galaxies. Both these effects are expected to be more significant for LSST than for the stage III experiments such as the Dark Energy Survey. We calculate the magnitude of the mass error (or bias) for the first time and demonstrate that it can be treated as a multiplicative correction and calibrated out, allowing mass measurements of clusters from gravitational lensing to meet the requirements of LSST's dark energy investigation.

Sediment traps with guiding channel and hybrid check dams improve controlled sediment retention

Science.gov (United States)

Schwindt, Sebastian; Franca, Mário J.; Reffo, Alessandro; Schleiss, Anton J.

2018-03-01

Sediment traps with partially open check dams are crucial elements for flood protection in alpine regions. The trapping of sediment is necessary when intense sediment transport occurs during floods that may endanger urban areas at downstream river reaches. In turn, the unwanted permanent trapping of sediment during small, non-hazardous floods can result in the ecological and morphological degradation of downstream reaches. This study experimentally analyses a novel concept for permeable sediment traps. For ensuring the sediment transfer up to small floods, a guiding channel implemented in the deposition area of a sediment trap was systematically studied. The bankfull discharge of the guiding channel corresponds to a dominant morphological discharge. At the downstream end of the guiding channel, a permeable barrier (check dam) triggers sediment retention and deposition. The permeable barrier consists of a bar screen for mechanical deposition control, superposed to a flow constriction for the hydraulic control. The barrier obstructs hazardous sediment transport for discharges that are higher than the bankfull discharge of the guiding channel without the risk of unwanted sediment flushing (massive self-cleaning).

Investigation of Composition of Particle Size in Sediments of Stormwater Sedimentation Tank

OpenAIRE

Daiva Laučytė; Regimantas Dauknys

2011-01-01

The main object for the storm water runoff treatment is to remove suspended solids before the storm water runoff is discharged into surface waters. Therefore the sedimentation tank is the most often used treatment facility. In order to optimise the sedimentation, the tendency of particle size distribution in bottom sediments must be known. Two similar size storm water runoff sedimentation tanks in Vilnius city were selected for the analysis of the particle size distribution in sediments. The ...

Sedimentation

Science.gov (United States)

Cliff R. Hupp; Michael R. Schening

2000-01-01

Sedimentation is arguably the most important water-quality concern in the United States. Sediment trapping is cited frequently as a major function of riverine-forested wetlands, yet little is known about sedimcntation rates at the landscape scale in relation to site parameters, including woody vegetation type, elevation, velocity, and hydraulic connection to the river...

Assessing sediment hazard through a weight of evidence approach with bioindicator organisms: a practical model to elaborate data from sediment chemistry, bioavailability, biomarkers and ecotoxicological bioassays.

Science.gov (United States)

Piva, Francesco; Ciaprini, Francesco; Onorati, Fulvio; Benedetti, Maura; Fattorini, Daniele; Ausili, Antonella; Regoli, Francesco

2011-04-01

Quality assessments are crucial to all activities related to removal and management of sediments. Following a multidisciplinary, weight of evidence approach, a new model is presented here for comprehensive assessment of hazards associated to polluted sediments. The lines of evidence considered were sediment chemistry, assessment of bioavailability, sub-lethal effects on biomarkers, and ecotoxicological bioassays. A conceptual and software-assisted model was developed with logical flow-charts elaborating results from each line of evidence on the basis of several chemical and biological parameters, normative guidelines or scientific evidence; the data are thus summarized into four specific synthetic indices, before their integration into an overall sediment hazard evaluation. This model was validated using European eels (Anguilla anguilla) as the bioindicator species, exposed under laboratory conditions to sediments from an industrial site, and caged under field conditions in two harbour areas. The concentrations of aliphatic hydrocarbons, polycyclic aromatic hydrocarbons and trace metals were much higher in the industrial compared to harbour sediments, and accordingly the bioaccumulation in liver and gills of exposed eels showed marked differences between conditions seen. Among biomarkers, significant variations were observed for cytochrome P450-related responses, oxidative stress biomarkers, lysosomal stability and genotoxic effects; the overall elaboration of these data, as those of standard ecotoxicological bioassays with bacteria, algae and copepods, confirmed a higher level of biological hazard for industrial sediments. Based on comparisons with expert judgment, the model presented efficiently discriminates between the various conditions, both as individual modules and as an integrated final evaluation, and it appears to be a powerful tool to support more complex processes of environmental risk assessment. Copyright © 2010 Elsevier Ltd. All rights reserved.

Investigation of Composition of Particle Size in Sediments of Stormwater Sedimentation Tank

Directory of Open Access Journals (Sweden)

Daiva Laučytė

2011-04-01

Full Text Available The main object for the storm water runoff treatment is to remove suspended solids before the storm water runoff is discharged into surface waters. Therefore the sedimentation tank is the most often used treatment facility. In order to optimise the sedimentation, the tendency of particle size distribution in bottom sediments must be known. Two similar size storm water runoff sedimentation tanks in Vilnius city were selected for the analysis of the particle size distribution in sediments. The composite samples of drained storm water runoff sediments were collected at the sedimentation tanks located in the districts of Verkiai and Karoliniskes on the 2nd of June, 2008. The analyses of grain size distribution were performed according the standard ISO/TS 17892-4:2004. The results showed that the particles with the particle size of 1–2 mm were obtained up to 10 m from the inlet and the particles with the size of 0,01–0,05 mm mainly were obtained close to the outlet of sedimentation tank. It is recommended to divide the sedimentation tank in two parts in order to get proper management of sediments: the particles that size is 1–10 mm could be managed as waste from grit chambers and particles of smaller size could be managed as primary sludge.Article in Lithuanian

CEEM Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bowers, John [Univ. of California, Santa Barbara, CA (United States)

2014-11-26

concentrating photovoltaic applications thathave substantially higher efficiency than single substrate cells made of elemental semiconductors such as silicon. This task required the development of new cell bonding methods with excellent coupling of both photons and electrons between the sub-cells. To accomplish this, we developed (1) GaInN solar cells with enhanced performance by using quantum-well absorbers and front-surface optical texturing, (2) a hybrid "pillar-array" bond which uses an array of metal pillars for electrical coupling, and (3) a "hybrid moth-eye" optical coating which combines the benefits of nano-imprinted moth-eye coatings and traditional multilayer coatings. The technical effectiveness was assessed by measurement of the photovoltaic efficiency of solar cells made using these techniques; the ultrahigh efficiencies targeted by this work are of compelling economic value for concentrating photovoltaics.

Measurable Control System Security through Ideal Driven Technical Metrics

Energy Technology Data Exchange (ETDEWEB)

Miles McQueen; Wayne Boyer; Sean McBride; Marie Farrar; Zachary Tudor

2008-01-01

The Department of Homeland Security National Cyber Security Division supported development of a small set of security ideals as a framework to establish measurable control systems security. Based on these ideals, a draft set of proposed technical metrics was developed to allow control systems owner-operators to track improvements or degradations in their individual control systems security posture. The technical metrics development effort included review and evaluation of over thirty metrics-related documents. On the bases of complexity, ambiguity, or misleading and distorting effects the metrics identified during the reviews were determined to be weaker than necessary to aid defense against the myriad threats posed by cyber-terrorism to human safety, as well as to economic prosperity. Using the results of our metrics review and the set of security ideals as a starting point for metrics development, we identified thirteen potential technical metrics - with at least one metric supporting each ideal. Two case study applications of the ideals and thirteen metrics to control systems were then performed to establish potential difficulties in applying both the ideals and the metrics. The case studies resulted in no changes to the ideals, and only a few deletions and refinements to the thirteen potential metrics. This led to a final proposed set of ten core technical metrics. To further validate the security ideals, the modifications made to the original thirteen potential metrics, and the final proposed set of ten core metrics, seven separate control systems security assessments performed over the past three years were reviewed for findings and recommended mitigations. These findings and mitigations were then mapped to the security ideals and metrics to assess gaps in their coverage. The mappings indicated that there are no gaps in the security ideals and that the ten core technical metrics provide significant coverage of standard security issues with 87% coverage. Based

Technical water system of the Reactor - Design description, operation regime and manipulation

International Nuclear Information System (INIS)

Badrljica, R.

1984-05-01

Technical water, reactor secondary coolant system is made of four parts: pumping station on the Danube; sedimentation facility in the village Vinca; coolant, heat exchangers and other elements within the RA reactor building; leading outer pipes and the stream Mlaka. All the four parts are connected to form a functional entirety, and each of them connected to cooling heat exchangers forms a partial functional system which enable the whole system to fulfill its fundamental task [sr

Importance of measuring discharge and sediment transport in lesser tributaries when closing sediment budgets

Science.gov (United States)

Griffiths, Ronald E.; Topping, David J.

2017-11-01

Sediment budgets are an important tool for understanding how riverine ecosystems respond to perturbations. Changes in the quantity and grain size distribution of sediment within river systems affect the channel morphology and related habitat resources. It is therefore important for resource managers to know if a river reach is in a state of sediment accumulation, deficit or stasis. Many sediment-budget studies have estimated the sediment loads of ungaged tributaries using regional sediment-yield equations or other similar techniques. While these approaches may be valid in regions where rainfall and geology are uniform over large areas, use of sediment-yield equations may lead to poor estimations of loads in regions where rainfall events, contributing geology, and vegetation have large spatial and/or temporal variability. Previous estimates of the combined mean-annual sediment load of all ungaged tributaries to the Colorado River downstream from Glen Canyon Dam vary by over a factor of three; this range in estimated sediment loads has resulted in different researchers reaching opposite conclusions on the sign (accumulation or deficit) of the sediment budget for particular reaches of the Colorado River. To better evaluate the supply of fine sediment (sand, silt, and clay) from these tributaries to the Colorado River, eight gages were established on previously ungaged tributaries in Glen, Marble, and Grand canyons. Results from this sediment-monitoring network show that previous estimates of the annual sediment loads of these tributaries were too high and that the sediment budget for the Colorado River below Glen Canyon Dam is more negative than previously calculated by most researchers. As a result of locally intense rainfall events with footprints smaller than the receiving basin, floods from a single tributary in semi-arid regions can have large (≥ 10 ×) differences in sediment concentrations between equal magnitude flows. Because sediment loads do not

Economic Reform Orchestra And Technical Manpower Development ...

African Journals Online (AJOL)

The study examined economic reform issues in Nigeria since 1986 and the impact on technical manpower development in Rivers State in particular. Two sets of structured questionnaire were used to elicit responses from target respondents who ultimately comprised 105 instructors and 340 final year students in the four ...

[Review comments on the Draft DOE Area Recommendation Report for the Crystalline Repository Project]: Final technical report

International Nuclear Information System (INIS)

Dutch, S.I.; Stiegliltz, R.D.

1986-03-01

Research performed under the grant primarily involved review and comment on the Draft Area Recommendations Report (DARR). However, because data and ''recommendations'' included in the DARR are unquestionably tied to years of research and dozens of technical reports and documents, i.e., Screening Methodologies, Regional characterization Reports, etc., it is essential that consultants to the Menominee Tribe review all the relevant DOE documents, working papers, etc. Given the short period provided for technical comment and limited funds available to the Tribe, a well designed and thorough technical review was (and is) without question impossible. What review and comment that did occur on a geotechnical level is included in this report

Climate vs. tectonic induced variations in Cenozoic sediment supply from western Scandinavia

DEFF Research Database (Denmark)

Gołędowski, Bartosz; Nielsen, S.B.; Clausen, O.R.

The scope of this work is the causality of sediment flux variations from western Scandinavia during the Cenozoic. Over the decades of exploration in the North Sea and in the Norwegian shelf most of these variations were given tectonic causes. During the final period of North Atlantic break......-up (Paleocene-Early Eocene) this link is quite striking, especially in the northern British Isles and in the Faeroe-Shetland Platform where sediment production pulses can be correlated with well documented periods of tectonic activity (e.g. magmatism). However, during the subsequent Cenozoic epochs this link...... is much less constrained. For this period we therefore search for an alternative explanation in terms of climate and climate change [1-3] Methods The extensive seismic and well data set allow investigation of inland erosion rates via the offshore distribution of sediments. However, varying marine...

Improved Barriers to Turbine Engine Fragments: Final Annual Report

National Research Council Canada - National Science Library

Shockey, Donald

2002-01-01

This final annual technical report describes the progress rnade during year 4 of the SPI International Phase II effort to develop a computational capability for designing lightweight fragment barriers...

How to be an Effective Technical Writer?

Directory of Open Access Journals (Sweden)

M Solaiman Ali

2012-07-01

(patterns of organization of information to suit the technical writing task, checking for technical accuracy and following three levels of editing to help increase the readability of a technical text. Finally, in part 8 (Ethical/legal considerations for the technical writer, the authors suggest ways for the technical writer to overcome ethical/legal dilemmas on the job.

Technical Report Cellulosic Based Black Liquor Gasification and Fuels Plant Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Fornetti, Micheal [Escanaba Paper Company, MI (United States); Freeman, Douglas [Escanaba Paper Company, MI (United States)

2012-10-31

The Cellulosic Based Black Liquor Gasification and Fuels Plant Project was developed to construct a black liquor to Methanol biorefinery in Escanaba, Michigan. The biorefinery was to be co-located at the existing pulp and paper mill, NewPage’s Escanaba Paper Mill and when in full operation would: • Generate renewable energy for Escanaba Paper Mill • Produce Methanol for transportation fuel of further refinement to Dimethyl Ether • Convert black liquor to white liquor for pulping. Black liquor is a byproduct of the pulping process and as such is generated from abundant and renewable lignocellulosic biomass. The biorefinery would serve to validate the thermochemical pathway and economic models for black liquor gasification. It was a project goal to create a compelling new business model for the pulp and paper industry, and support the nation’s goal for increasing renewable fuels production and reducing its dependence on foreign oil. NewPage Corporation planned to replicate this facility at other NewPage Corporation mills after this first demonstration scale plant was operational and had proven technical and economic feasibility. An overview of the process begins with black liquor being generated in a traditional Kraft pulping process. The black liquor would then be gasified to produce synthesis gas, sodium carbonate and hydrogen sulfide. The synthesis gas is then cleaned with hydrogen sulfide and carbon dioxide removed, and fed into a Methanol reactor where the liquid product is made. The hydrogen sulfide is converted into polysulfide for use in the Kraft pulping process. Polysulfide is a known additive to the Kraft process that increases pulp yield. The sodium carbonate salts are converted to caustic soda in a traditional recausticizing process. The caustic soda is then part of the white liquor that is used in the Kraft pulping process. Cellulosic Based Black Liquor Gasification and Fuels Plant project set out to prove that black liquor gasification could

Chronicling ice shelf history in the sediments left behind

Science.gov (United States)

Rosenheim, B. E.; Subt, C.; Shevenell, A.; Guitard, M.; Vadman, K. J.; DeCesare, M.; Wellner, J. S.; Bart, P. J.; Lee, J. I.; Domack, E. W.; Yoo, K. C.; Hayes, J. M.

2017-12-01

Collapsing and retreating ice shelves leave unmistakable sediment sequences on the Antarctic margin. These sequences tell unequivocal stories of collapse or retreat through a typical progression of sub-ice shelf diamicton (marking the past positions of grounding lines), sequentially overlain by a granulated facies from beneath the ice shelf, ice rafted debris from the calving line, and finally open marine sediment. The timelines to these stories, however, are troublesome. Difficulties in chronicling these stories recorded in sediment have betrayed their importance to our understanding of a warming world in many cases. The difficulties involve the concerted lack of preservation/production of calcium carbonate tests from the water column above and admixture of relict organic material from older sources of carbon. Here, we summarize our advances in the last decade of overcoming difficulties associated with the paucity of carbonate and creating chronologies of ice shelf retreat into the deglacial history of Antarctica by exploiting the range of thermochemical stability in organic matter (Ramped PyrOx) from these sediment sequences. We describe our success in comparing Ramped PyrOx 14C dates with foraminiferal dates, the relationship between sediment facies and radiocarbon age spectrum, and our ability to push limits of dating sediments deposited underneath ice shelves. With attention to the caveats of recent dating developments, we summarize expectations that geologist should have when coring the Antarctic margins to discern deglacial history. Perhaps most important among these expectations is the ability to design coring expeditions without regard to our ability to date calcium carbonate microfossils within the cores, in essence removing suspense of knowing whether cores taken from crucial paleo ice channels and other bathymetric features will ultimately yield a robust chronology for its sedimentary sequence.

Cobalt and tantalum tracers measured by activation analysis in sediment transport studies

Energy Technology Data Exchange (ETDEWEB)

Groot, A.J. de [Institute for Soil Fertility, Haren (Netherlands); Allersma, E [Delft Hydraulics Laboratory, Delft (Netherlands); Bruin, M de; Houtman, J P.W. [Reactor Institute, Delft (Netherlands)

1970-09-15

The paper proposes certain principles of research to be used in investigating the origin and transport of fine-grained sediments in rivers and sea arms in connection with siltation problems of harbours and navigation channels. An element, which either does not occur in the sediment or only occurs in minute quantities, is fixed to the mud from the river or sea arm. After the material is marked it is returned to the water course where it mixes with the solids moving naturally. At specified points throughout the water course sediment samples are taken to determine the marking element by activation analysis. This gives an insight into the flow path of the suspended matter. The selection and successful application of tracers that can be measured by activation analysis depends on the sensitivity of detection, the natural occurrence of the relevant elements in the sediments under investigation and the fixation capacity of the tracer to the various grain size fractions. Further, the influence of the added element on the sedimentation behaviour of the mud in suspension and on the desorption properties must be considered. The irradiation of Co and Ta with thermal neutrons gives rise to a very sensitive evaluation of the original elements present. The fixation process of Co is restricted to sediments with special characteristics; Ta, however, can adhere tightly to any sediment. Tantalum also has the advantage that its natural content in sediments is very low. Large quantities (several per cent by weight) can adhere to the sediment without changing the sedimentation properties to an appreciable extent. Hardly any losses occur during leaching experiments simulating natural conditions. A detailed treatment is given of the chemical aspects of the method, including the behaviour of the elements used in the light of the general environmental processes of sediment constituents in deltaic systems. Finally, the scope and limits of the method are discussed. (author)

Cobalt and Tantalum Tracers Measured by Activation Analysis in Sediment Transport Studies

Energy Technology Data Exchange (ETDEWEB)

Groot, A.J. de [Institute for Soil Fertility, Haren (Netherlands); Allersma, E. [Delft Hydraulics Laboratory, Delft (Netherlands); Bruin, M. de; Houtman, J. P.W. [Reactor Institute, Delft (Netherlands)

1970-09-15

The paper proposes certain principles of research to be used in investigating the origin and transport of fine-grained sediments in rivers and sea arms in connection with siltation problems of harbours and navigation channels. An element, which either does not occur in the sediment or only occurs in minute quantities, is fixed to the mud from the river or sea arm. After the material is marked it is returned to the water course where it mixes with the solids moving naturally. At specified points throughout the water course sediment samples are taken to determine the marking element by activation analysis. This gives an insight into the flow path of the suspended matter. The selection and successful application of tracers that can be measured by activation analysis depends on the sensitivity of detection, the natural occurrence of the relevant elements in the sediments under investigation and the fixation capacity of the tracer to the various grain size fractions. Further, the influence of the added element on the sedimentation behaviour of the mud in suspension and on the desorption properties must be considered. The irradiation of Co and Ta with thermal neutrons gives rise to a very sensitive evaluation of the original elements present. The fixation process of Co is restricted to sediments with special characteristics; Ta, however, can adhere tightly to any sediment. Tantalum also has the advantage that its natural content in sediments is very low. Large quantities (several per cent by weight) can adhere to the sediment without changing the sedimentation properties to an appreciable extent. Hardly any losses occur during leaching experiments simulating natural conditions. A detailed treatment is given of the chemical aspects of the method, including the behaviour of the elements used in the light of the general environmental processes of sediment constituents in deltaic systems. Finally, the scope and limits of the method are discussed. (author)

Organisation, Quality and Challenges in the B. Ed Technical ...

African Journals Online (AJOL)

Technical) degree programme rated the organization and quality of the industrial attachment component of the programme. Challenges students faced during industrial attachment were also examined. A case study design was used. Twenty-five final ...

Site-specific sediment clean-up objectives developed by the sediment quality triad

International Nuclear Information System (INIS)

Redman, S.; Janisch, T.

1995-01-01

Sediment chemistry, sediment toxicity, and benthic macroinvertebrate community data were collected and evaluated in concert (1) to characterize adverse effects of hydrocarbon and metal contaminants in the sediments of a small inlet of Superior Bay, Lake Superior and a tributary creek and (2) to derive numeric objectives for the clean up of this system. Sediments from reference locations and eight study sites were analyzed for a range of contaminants, including hydrocarbons (measured both as diesel range organics (DRO) and oil and grease), lead, chromium, and ammonia. A range of sediment toxicity was observed across the eight study sites using a variety of tests and endpoints: Hyalella azteca (10 day survival and growth), Chironomus tentans (10 day survival and growth), Ceriodaphnia dubia (48 hour survival), and Daphnia magna (48 hour survival and 10 day survival and reproduction). A range of alterations of the benthic macroinvertebrate community compared with communities from reference locations were observed. Benthic community alterations were summarized quantitatively by taxa richness and Shannon-Weiner mean diversity. Lowest effect levels determined through this study included 150 microg/g dry sediment for DRO (as measured in this study) and 40 microg/g dry sediment for lead. Effects thresholds determined through this study included 1,500 microg/g dry sediment for DRO and 90 microg/g dry sediment for lead. These levels and concentrations measured in relevant reference locations are being used to define objectives for sediment clean up in the inlet and creek

Program of technical assistance to the Organization for the Prohibition of Chemical Weapons - lessons learned from the U.S. program of technical assistance to IAEA safeguards. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

The Defense Nuclear Agency is sponsoring a technical study of the requirements of a vehicle to meet the OPCW`s future needs for enhanced chemical weapons verification capabilities. This report provides information about the proven mechanisms by which the U.S. provided both short- and long-term assistance to the IAEA to enhance its verification capabilities. Much of the technical assistance has generic application to international organizations verifying compliance with disarmament treaties or conventions. In addition, some of the equipment developed by the U.S. under the existing arrangements can be applied in the verification of other disarmament treaties or conventions. U.S. technical assistance to IAEA safeguards outside of the IAEA`s regular budget proved to be necessary. The U.S. technical assistance was successful in improving the effectiveness of IAEA safeguards for its most urgent responsibilities and in providing the technical elements for increased IAEA {open_quotes}readiness{close_quotes} for the postponed responsibilities deemed important for U.S. policy objectives. Much of the technical assistance was directed to generic subjects and helped to achieve a system of international verification. It is expected that the capabilities of the Organization for the Prohibition of Chemical Weapons (OPCW) to verify a state`s compliance with the {open_quotes}Chemical Weapons Convention{close_quotes} will require improvements. This report presents 18 important lessons learned from the experience of the IAEA and the U.S. Program of Technical Assistance to IAEA Safeguards (POTAS), organized into three tiers. Each lesson is presented in the report in the context of the difficulty, need and history in which the lesson was learned. Only the most important points are recapitulated in this executive summary.

Effects of sediment application on Nyssa aquatica and Taxodium distichum saplings

Science.gov (United States)

Grandy, Isabel; Messina, Linda; Anemaet, Evelyn R.; Middleton, Beth A.

2018-01-01

The decline of Taxodium distichum forests along the Gulf Coast of North America is partly due to elevation loss and subsequent flooding. In many coastal wetlands, a common approach for coastal restoration is to rebuild elevation through the application of dredge material, but this technique has not been used widely in coastal forests due to concerns of negatively impacting trees. This experiment explored growth responses of Nyssa aquatica and T. distichumsaplings to applications of low salinity dredge material (0.08 ± 0.001 ppt) in a greenhouse setting. Compared to controls, saplings of T. distichum grown in 7 and 15 cm sediment depths had greater final height, and increased stem and total biomass. In contrast, N. aquatica did not respond to sediment application. The absence of a negative response to sediment application in these two species indicates that dredge material application has the potential to improve the ecosystem health of sinking swamp forests by raising their elevation. We recommend that field trials applying sediment additions in coastal forests include careful monitoring of ecosystem responses, including seed bank expression, seedling regeneration, and root and canopy production.

Technical activities, 1990: Surface Science Division

International Nuclear Information System (INIS)

Powell, C.J.

1991-05-01

The report summarizes technical activities and accomplishments of the NIST Surface Science Division during Fiscal Year 1990. Overviews are presented of the Division and of its three constituent groups: Surface Dynamical Processes, Thin Films and Interfaces, and Surface Spectroscopies and Standards. These overviews are followed by reports of selected technical accomplishments during the year. A summary is given of Division outputs and interactions that includes lists of publications, talks, committee assignments, seminars (including both Division seminars and Interface Science seminars arranged through the Division), conferences organized, and a standard reference material certified. Finally, lists are given of Division staff and of guest scientists who have worked in the Division during the past year

Technical approach document

International Nuclear Information System (INIS)

1989-12-01

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs

Texas Hydrogen Education Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Hitchcock, David; Bullock, Dan

2011-06-30

, and hydrogen fueling) are effective for engaging target audiences, and (3) a clear path forward is needed for state and local agencies interested in project implementation (funding, financing, preliminary design, technical assistance, etc.).

Bioremediation of Contaminated Lake Sediments and Evaluation of Maturity Indicies as Indicators of Compost Stability

Directory of Open Access Journals (Sweden)

Y. Anjaneyulu

2005-08-01

Full Text Available Land contamination is one of the widely addressed problems, which is gaining importance in many developed and developing countries. International efforts are actively envisaged to remediate contaminated sites as a response to adverse health effects. Popular conventional methodologies only transfer the phase of the contaminant involving cost intensive liabilities besides handling risk of the hazardous waste. Physico-chemical methods are effective for specific wastes, but are technically complex and lack public acceptance for land remediation. “Bioremediation”, is one of the emerging low-cost technologies that offer the possibility to destroy various contaminants using natural biological activities. Resultant non -toxic end products due to the microbial activity and insitu applicability of this technology is gaining huge public acceptance. In the present study, composting is demonstrated as a bioremediation methodology for the stabilization of contaminated lake sediments of Hyderabad, A.P, India. Lake sediment contaminated with organics is collected from two stratums – upper (0.25 m and lower (0.5m to set up as Pile I (Upper and Pile II (Lower in the laboratory. Lime as a pretreatment to the lake sediments is carried out to ensure metal precipitation. The pretreated sediment is then mixed with organic and inorganic fertilizers like cow dung, poultry manure, urea and super phosphate as initial seeding amendments. Bulking agents like sawdust and other micronutrients are provided. Continuous monitoring of process control parameters like pH, moisture content, electrical conductivity, total volatile solids and various forms of nitrogen were carried out during the entire course of the study. The stability of the compost was evaluated by assessing maturity indices like C/N, Cw (water soluble carbon, CNw (Cw/Nw, nitrification index (NH4/NO-3, Cation Exchange Capacity (CEC, germination index, humification ratio, compost

Quantitative research for pollution levels in marine sediments of Ha Long Bay by nuclear technique

International Nuclear Information System (INIS)

Nguyen Quang Long; Tran Thi Tuyet Mai; Pham Ngoc Khai; Nguyen Trung Thanh; Nguyen Van Phuc; Doan Thuy Hau; Duong Van Thang; Ha Lan Anh; Vo Thi Anh; Nguyen Thi Thu Ha

2013-01-01

Under the theme of Quantitative study of pollution levels in marine sediments of Halong bay by nuclear techniques conducted from June 2011 to June 2013, the authors conducted monitoring, sediment samples collected in the bay below the sediment column at 8 locations, in which 7 columns located at the estuary near Tuan Chau Island and 1 column at the area near the harbor of Cam Pha. The column samples were taken to the laboratory, cut slices with a distance of 2 cm in the form of frozen and conduct tests of radioactive Pb-210 to determine the rate of sediment in the survey area. Evaluation results based on the method by determining 210 Pb, the sediment rate showed speed in the survey area ranged from 0.3 cm.a -1 to 1.2 cm.a -1 and an average of 1.0 cm.a -1 . The slices of sediment samples (110 samples) were analyzed heavy metals (KLN) and As elemental by ICP-MS method. These sediment sample also were analyzed for simultaneous determination of N and P and total organic carbon (TOC). Results showed that heavy metal concentrations and As is smaller than the value specified in the National Technical Regulation on Sediment Quality of Vietnam (QCVN), phosphorus concentration less than that can cause harmful effects, but the concentration of total nitrogen and organic carbon that may exceed be harmful as directed by Canadian standards (Persuad et al. 1992). The concentration data in the Halong bay sediment were processed by statistical software SPSS-18, results showed high correlation between the quality TOC, N, P, K and correlation the majority of KLN, this proves the origin of sediments is part of the natural soil components and parts (TOC, N, P, K) is due to the activity of human activity as well as by agricultural fertilizers. The average content of elements in sediments Halong be compared with other data published works of sediment Quang Ninh area, the results show the correlation figures are also high. However, the results of the analysis of KLN and As in Halong

Radiological Effluent Technical Specifications (RETS) implementation, Kewaunee Nuclear Power Plant

International Nuclear Information System (INIS)

Serrano, W.; Akers, D.W.

1985-06-01

A review of the Radiological Effluent Technical Specifications (RETS) for the Kewaunee Nuclear Power Plant was performed. The principal review guidelines used were NUREG-0133, ''Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants,'' and Draft 7'' of NUREG-0472, Revision 3, ''Radiological Effluent Technical Specifications for Pressurized Water Reactors.'' Draft submittals were discussed with the Licensee by the NRC staff until all items requiring changes to the Technical Specifications were resolved. The Licensee then submitted final proposed RETS to the NRC which were evaluated and found to be in compliance with the NRC review guidelines. The proposed Offsite Dose Calculation Manual and the Radiological Environmental Monitoring Manual were reviewed and generally found to be in compliance with the NRC review guidelines

SIAM Conference on Geometric Design and Computing. Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

None

2002-03-11

The SIAM Conference on Geometric Design and Computing attracted 164 domestic and international researchers, from academia, industry, and government. It provided a stimulating forum in which to learn about the latest developments, to discuss exciting new research directions, and to forge stronger ties between theory and applications. Final Report

Investigations of grain size dependent sediment transport phenomena on multiple scales

Science.gov (United States)

Thaxton, Christopher S.

Sediment transport processes in coastal and fluvial environments resulting from disturbances such as urbanization, mining, agriculture, military operations, and climatic change have significant impact on local, regional, and global environments. Primarily, these impacts include the erosion and deposition of sediment, channel network modification, reduction in downstream water quality, and the delivery of chemical contaminants. The scale and spatial distribution of these effects are largely attributable to the size distribution of the sediment grains that become eligible for transport. An improved understanding of advective and diffusive grain-size dependent sediment transport phenomena will lead to the development of more accurate predictive models and more effective control measures. To this end, three studies were performed that investigated grain-size dependent sediment transport on three different scales. Discrete particle computer simulations of sheet flow bedload transport on the scale of 0.1--100 millimeters were performed on a heterogeneous population of grains of various grain sizes. The relative transport rates and diffusivities of grains under both oscillatory and uniform, steady flow conditions were quantified. These findings suggest that boundary layer formalisms should describe surface roughness through a representative grain size that is functionally dependent on the applied flow parameters. On the scale of 1--10m, experiments were performed to quantify the hydrodynamics and sediment capture efficiency of various baffles installed in a sediment retention pond, a commonly used sedimentation control measure in watershed applications. Analysis indicates that an optimum sediment capture effectiveness may be achieved based on baffle permeability, pond geometry and flow rate. Finally, on the scale of 10--1,000m, a distributed, bivariate watershed terain evolution module was developed within GRASS GIS. Simulation results for variable grain sizes and for

Terrestrial Sediments of the Earth: Development of a Global Unconsolidated Sediments Map Database (GUM)

Science.gov (United States)

Börker, J.; Hartmann, J.; Amann, T.; Romero-Mujalli, G.

2018-04-01

Mapped unconsolidated sediments cover half of the global land surface. They are of considerable importance for many Earth surface processes like weathering, hydrological fluxes or biogeochemical cycles. Ignoring their characteristics or spatial extent may lead to misinterpretations in Earth System studies. Therefore, a new Global Unconsolidated Sediments Map database (GUM) was compiled, using regional maps specifically representing unconsolidated and quaternary sediments. The new GUM database provides insights into the regional distribution of unconsolidated sediments and their properties. The GUM comprises 911,551 polygons and describes not only sediment types and subtypes, but also parameters like grain size, mineralogy, age and thickness where available. Previous global lithological maps or databases lacked detail for reported unconsolidated sediment areas or missed large areas, and reported a global coverage of 25 to 30%, considering the ice-free land area. Here, alluvial sediments cover about 23% of the mapped total ice-free area, followed by aeolian sediments (˜21%), glacial sediments (˜20%), and colluvial sediments (˜16%). A specific focus during the creation of the database was on the distribution of loess deposits, since loess is highly reactive and relevant to understand geochemical cycles related to dust deposition and weathering processes. An additional layer compiling pyroclastic sediment is added, which merges consolidated and unconsolidated pyroclastic sediments. The compilation shows latitudinal abundances of sediment types related to climate of the past. The GUM database is available at the PANGAEA database (https://doi.org/10.1594/PANGAEA.884822).

Morphodynamics and Sediment Transport on the Huanghe (Yellow River) Delta: Work in Progress

Science.gov (United States)

Kineke, G. C.; Calson, B.; Chadwick, A. J.; Chen, L.; Hobbs, B. F.; Kumpf, L. L.; Lamb, M. P.; Ma, H.; Moodie, A. J.; Mullane, M.; Naito, K.; Nittrouer, J. A.; Parker, G.

2017-12-01

Deltas are perhaps the most dynamic of coastal landforms with competing processes that deliver and disperse sediment. As part of the NSF Coastal SEES program, an interdisciplinary team of scientists from the US and China are investigating processes that link river and coastal sediment transport responsible for morphodynamic change of the Huanghe delta- an excellent study site due to its high sediment load and long history of natural and engineered avulsions, that is, abrupt shifts in the river course. A fundamental component of the study is a better understanding of sediment transport physics in a river system that transports mostly silt. Through theory and data analysis, we find that fine-grained rivers fail to develop full scale dunes, which results in faster water flow and substantially larger sediment fluxes as compared to sandy rivers (e.g. the Mississippi River). We also have developed new models for sediment-size dependent entrainment that are needed to make longer term predictions of river sedimentation patterns. On the delta front, we are monitoring the high sediment flux to the coast, which results in steep foresets and ideal conditions for off-shore sediment delivery via gravity flows. These constraints on sediment transport are being used to develop new theory for where and when rivers avulse - including the effects of variable flood discharge, sediment supply, and sea level rise -and how deltas ultimately grow through repeated cycles of lobe development. Flume experiments and field observations are being used to test these models, both in the main channel of the Huanghe and in channels abandoned after historic avulsions. Abandoned channels and floodplains are now dominated by coastal sediment transport through a combination of wave resuspension and tidal transport, settling lag and reverse estuarine circulation. Finally, the field and laboratory tested numerical models are being used as inputs to define a cost curve for efficient avulsion management of

77 FR 8095 - Technical Corrections to Commission Regulations

Science.gov (United States)

2012-02-14

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission 18 CFR Part 2 [Docket No. RM11-30-000; Order No. 756] Technical Corrections to Commission Regulations Issued February 8, 2012. AGENCY: Federal Energy Regulatory Commission, DOE. ACTION: Final rule: correcting amendment. SUMMARY: This document adds...

76 FR 16235 - Corporate Credit Unions, Technical Corrections

Science.gov (United States)

2011-03-23

... inadvertently included particular investments that did not--when subject to the other credit risk and asset... NATIONAL CREDIT UNION ADMINISTRATION 12 CFR Part 707 RIN 3133-AD58 Corporate Credit Unions, Technical Corrections AGENCY: National Credit Union Administration (NCUA). ACTION: Final rule. SUMMARY: In...

A discrete element model for the influence of surfactants on sedimentation characteristics of magnetorheological fluids

Science.gov (United States)

Son, Kwon Joong

2018-02-01

Hindering particle agglomeration and re-dispersion processes, gravitational sedimentation of suspended particles in magnetorheological (MR) fluids causes inferior performance and controllability of MR fluids in response to a user-specified magnetic field. Thus, suspension stability is one of the principal factors to be considered in synthesizing MR fluids. However, only a few computational studies have been reported so far on the sedimentation characteristics of suspended particles under gravity. In this paper, the settling dynamics of paramagnetic particles suspended in MR fluids was investigated via discrete element method (DEM) simulations. This work focuses particularly on developing accurate fluid-particle and particle-particle interaction models which can account for the influence of stabilizing surfactants on the MR fluid sedimentation. Effect of the stabilizing surfactants on interparticle interactions was incorporated into the derivation of a reliable contact-impact model for DEM computation. Also, the influence of the stabilizing additives on fluid-particle interactions was considered by incorporating Stokes drag with shape and wall correction factors into DEM formulation. The results of simulations performed for model validation purposes showed a good agreement with the published sedimentation measurement data in terms of an initial sedimentation velocity and a final sedimentation ratio.

Coupling climate conditions, sediment sources and sediment transport in an alpine basin

Science.gov (United States)

Rainato, Riccardo; Picco, Lorenzo; Cavalli, Marco; Mao, Luca; Neverman, Andrew J.; Tarolli, Paolo

2017-04-01

In a fluvial system, mountain basins control sediment export to the lowland rivers. Hence, the analysis of the erosion processes and sediment delivery patterns that act in mountain basins is important. Several studies have investigated the alterations triggered by recent climatic change on the hydrological regime, whilst only a few works have explored the consequences on the sediment dynamics. Here we combined and analyzed the quasi-unique dataset of climatic conditions, landscape response, and sediment export produced, since 1986 in the Rio Cordon basin (5 km2, Eastern Italian Alps) to examine the sediment delivery processes occurring in the last three decades. The temperature, precipitation, and fluvial sediment fluxes in the basin were analyzed using continuous measurement executed by a permanent monitoring station, while the landscape evolution was investigated by three sediment source inventories established in 1994, 2006, and 2016. Thus, the analysis focused on the trends exhibited during the periods 1986-1993, 1994-2006, and 2007-2015. In terms of climatic conditions, three distinct climate forcing stages can be observed in the periods analyzed: a relatively stable phase (1986-1993), a period characterized by temperature and rainfall fluctuations (1994-2006), and a more recent warmer and wetter phase (2007-2015). In the 1986-1993 period, the fluvial sediment fluxes reflected the stable trend exhibited by the climatic conditions. In the subsequent 1994-2006 period, the average temperature and precipitation were in line with that previously observed, although with higher interannual variability. Notwithstanding the climate forcing and the occurrence of high magnitude/low frequency floods that strongly influenced the source areas, between 1994 and 2006 the Rio Cordon basin showed relatively limited erosion activity. Hence, the climatic conditions and the landscape response can only partially explain the strong increase of sediment export recorded in the 1994

Leaching tendencies of uranium and regulated trace metals from the Hanford Site 300 Area North Process Pond sediments

International Nuclear Information System (INIS)

Serne, R.J.; LeGore, V.L.; Mattigod, S.V.

1994-09-01

Data are presented that address the leaching tendencies and the total chemical composition of metals in feed materials and soil-washed fines generated by Alternative Remediation Technology, Inc. during a pilot-scale soil physical separation test performed at the 300 Area North Process Pond (Facility 316-2) on the Hanford Site in the spring of 1994. Four 300 Area North Process Pond sediments and one sediment from outside the pond's fenced area were leach-tested using the Toxicity Characteristic Leach Procedure (TCLP) and other modified US Environmental Protection Agency and American Society for Testing and Materials protocols. Finally, leachate from the most contaminated sediment was used to load the Hanford sediment obtained outside the facility to evaluate the potential for contaminant adsorption onto natural sediments. The sediment characterization, leach, and adsorption results will be used in the evaluation of remedial alternatives in the 300-FF-1 Operable Unit Remedial Investigation/Feasibility Study

EFDC1D - A ONE DIMENSIONAL HYDRODYNAMIC AND SEDIMENT TRANSPORT MODEL FOR RIVER AND STREAM NETWORKS: MODEL THEORY AND USERS GUIDE

Science.gov (United States)

This technical report describes the new one-dimensional (1D) hydrodynamic and sediment transport model EFDC1D. This model that can be applied to stream networks. The model code and two sample data sets are included on the distribution CD. EFDC1D can simulate bi-directional unstea...

Alternation of Sediment Characteristics during Sediment Microbial Fuel Cells Amended Biochar

Science.gov (United States)

Yang, Xunan; Chen, Shanshan

2018-01-01

Sediment microbial fuel cells (SMFCs) are considered as a new technology in sediment remediation, while biochars can promote interspecies electron transfer in bioelectrochemical systems. We conducted the SMFCs amended with biochars to investigate their effects on of sediment characteristics. Results showed that the anode of SMFCs could oxidize the chemical oxidizable matter in sediments (by 4%-16%) correlating with the maximum power density (r=0.982, palternations under SMFC operation, which gave information on the element pool related to pollutants and the risk of the application of SMFCs.

Biotrans functional and technical description. Report of VIEWLS WP5, modelling studies

International Nuclear Information System (INIS)

Van Tilburg, X.; Egging, R.; Londo, H.M.

2006-01-01

The overall objectives of this project are to provide structured and clear data on the availability and performance of biofuels and to identify the possibilities and strategies towards large scale sustainable production, use and trading of biofuels for the transport sector in Europe, including Central and Eastern European Countries (CEEC). The report supplements the two other reports in the work package: 'Biofuel and Bio-energy implementation scenarios - final report of VIEWLS WP5' (2005) and 'VIEWLS modelling and analysis, technical data for biofuel production chains' (2005). This document contains a functional and technical description of the BioTrans model, accompanied by a description of the system. Section 2 contains a conceptual and functional description of the biofuel model. Section 3 describes the optimisation method in technical terms, discussing aspects like the target function and constraints used. Finally, section 4 discusses the input and output requirements for the BioTrans system

SUSTAINING OCCUPATIONAL INFORMATION FOR CAREER CHOICE AND DEVELOPMENT IN STUDENTS OF TECHNICAL COLLEGES IN ENUGU STATE, NIGERIA

OpenAIRE

Moses Ikebe Odo

2015-01-01

This study takes on the issue of sustaining occupational information for career choice and development in students of technical colleges in Enugu State, Nigeria. The method adopted for this study was the survey design and the population included were all final year students of the three government technical colleges in Enugu State of Nigeria. The technical colleges were sampled as follows: Government Technical College, Enugu (156 students); Government Technical College, Nsukka (148 students);...

Tank Farms Technical Safety Requirements. Volume 1 and 2

International Nuclear Information System (INIS)

CASH, R.J.

2000-01-01

The Technical Safety Requirements (TSRs) define the acceptable conditions, safe boundaries, basis thereof, and controls to ensure safe operation during authorized activities, for facilities within the scope of the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR)

Tank Farms Technical Safety Requirements [VOL 1 and 2

Energy Technology Data Exchange (ETDEWEB)

CASH, R.J.

2000-12-28

The Technical Safety Requirements (TSRs) define the acceptable conditions, safe boundaries, basis thereof, and controls to ensure safe operation during authorized activities, for facilities within the scope of the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR).

Beryllium-10 in Chesapeake Bay sediments: an indicator of sediment provenance

International Nuclear Information System (INIS)

Helz, G.R.; Valette-Silver, Nathalie

1992-01-01

In a plot of 10 Be vs. Fe, central Chesapeake Bay sediments can be segregated into distinct units. This plot reveals an unexpected, statistically significant difference between sediments on the eastern and western flanks of the main channel, implying different origins. Although the 10 Be concentrations in sediments from these two regions span as much as an order of magnitude range, the 10 Be/Fe ratios vary by an amount approximating analytical error alone. The large concentration ranges are ascribed to hydraulic sorting, which can produce variance in composition while not affecting ratios between grain surface components such as Fe and Be. On the basis of 10 Be/Fe signatures, sediments on the western flank of the main channel appear to have been derived from the Susquehanna or another Piedmont/Appalachian river. Sediments on the eastern flank may have been transported from the south, by landward flowing bottom currents, or may be relics of a Pleistocene estuarine system. Conditions under which 10 Be may prove a useful tool in sediment provenance studies elsewhere are discussed. (Author)

Quantifying and Modelling Long Term Sediment Dynamics in Catchments in Western Europe

Science.gov (United States)

Notebaert, B.; De Brue, H.; Verstraeten, G.; Broothaerts, N.

2015-12-01

Quantification of sediment dynamics allows to get insight in driving forces and internal dynamics of the sediment cascade system. A useful tool to achieve this is the sediment budget approach, which encompasses the quantification of different sinks and sources. A Holocene time-differentiated sediment budget has been constructed for the Belgian Dijle River catchment (720 km²), based on a large set of field data. The results show how soil erosion is driven by land use changes over longer timescales. Sediment redistribution and the relative importance of the different sinks also vary over time, mainly as a result of changing land use and related landscape connectivity. However, the coarse temporal resolution typically associated with Holocene studies complicates the understanding of sub-millennial scale processes. In a second step, the field-based sediment budget was combined with a modeling approach using Watem/Sedem, a spatially distributed model that simulates soil erosion and colluvial deposition. After validation of the model calibration against the sediment budget, the model was used in a sensitivity analysis. Results confirm the overwhelming influence of human land use on both soil erosion and landscape connectivity, whereas the climatic impact is comparatively small. In addition to catchment-wide simulations, the model also served to test the relative importance of lynchets and dry valleys in different environments. Finally, the geomorphic model was used to simulate past land use, taking into account equifinality. For this purpose, a large series of hypothetical time-independent land use maps of the Dijle catchment were modeled based on a multi-objective allocation algorithm, and applied in Watem/Sedem. Modeled soil erosion and sediment deposition outcomes for each scenario were subsequently compared with the field-based record, taking into account uncertainties. As such, the model allows to evaluate and select realistic land use scenarios for the Holocene.

Influence of Chironomus riparius (Diptera, Chironomidae) and Tubifex tubifex (Annelida, Oligochaeta) on oxygen uptake by sediments. Consequences of uranium contamination

Energy Technology Data Exchange (ETDEWEB)

Lagauzere, S. [Laboratoire de Radioecologie et d' Ecotoxicologie, Institut de Radioprotection et de Surete Nucleaire (IRSN), DEI/SECRE/LRE, Cadarache 186, BP 3, F-13115 Cedex, Saint Paul Lez Durance (France)], E-mail: lagauzere@gmail.com; Pischedda, L.; Cuny, P. [Laboratoire de Microbiologie, Geochimie et Ecologie Marines, UMR 6117 CNRS/COM/Universite de la Mediterranee, Campus de Luminy, Case 901, F-13288 Cedex 09, Marseille (France); Gilbert, F. [EcoLab, Laboratoire d' Ecologie Fonctionnelle, UMR 5245 CNRS/INP/Universite Paul Sabatier, 29 Rue Jeanne Marvig, F-31055 Cedex 4, Toulouse (France); Stora, G. [Laboratoire de Microbiologie, Geochimie et Ecologie Marines, UMR 6117 CNRS/COM/Universite de la Mediterranee, Campus de Luminy, Case 901, F-13288 Cedex 09, Marseille (France); Bonzom, J.-M. [Laboratoire de Radioecologie et d' Ecotoxicologie, Institut de Radioprotection et de Surete Nucleaire (IRSN), DEI/SECRE/LRE, Cadarache 186, BP 3, F-13115 Cedex, Saint Paul Lez Durance (France)

2009-04-15

The diffusive oxygen uptake (DOU) of sediments inhabited by Chironomus riparius and Tubifex tubifex was investigated using a planar oxygen optode device, and complemented by measurements of bioturbation activity. Additional experiments were performed within contaminated sediments to assess the impact of uranium on these processes. After 72 h, the two invertebrate species significantly increased the DOU of sediments (13-14%), and no temporal variation occurred afterwards. Within contaminated sediments, it was already 24% higher before the introduction of the organisms, suggesting that uranium modified the sediment biogeochemistry. Although the two species firstly reacted by avoidance of contaminated sediment, they finally colonized it. Their bioturbation activity was reduced but, for T. tubifex, it remained sufficient to induce a release of uranium to the water column and an increase of the DOU (53%). These results highlight the necessity of further investigations to take into account the interactions between bioturbation, microbial metabolism and pollutants. - This study highlights the ecological importance of bioturbation in metal-contaminated sediments.

Influence of Chironomus riparius (Diptera, Chironomidae) and Tubifex tubifex (Annelida, Oligochaeta) on oxygen uptake by sediments. Consequences of uranium contamination

International Nuclear Information System (INIS)

Lagauzere, S.; Pischedda, L.; Cuny, P.; Gilbert, F.; Stora, G.; Bonzom, J.-M.

2009-01-01

The diffusive oxygen uptake (DOU) of sediments inhabited by Chironomus riparius and Tubifex tubifex was investigated using a planar oxygen optode device, and complemented by measurements of bioturbation activity. Additional experiments were performed within contaminated sediments to assess the impact of uranium on these processes. After 72 h, the two invertebrate species significantly increased the DOU of sediments (13-14%), and no temporal variation occurred afterwards. Within contaminated sediments, it was already 24% higher before the introduction of the organisms, suggesting that uranium modified the sediment biogeochemistry. Although the two species firstly reacted by avoidance of contaminated sediment, they finally colonized it. Their bioturbation activity was reduced but, for T. tubifex, it remained sufficient to induce a release of uranium to the water column and an increase of the DOU (53%). These results highlight the necessity of further investigations to take into account the interactions between bioturbation, microbial metabolism and pollutants. - This study highlights the ecological importance of bioturbation in metal-contaminated sediments

Remediation of uranium impacted sediments in a watercourse

Energy Technology Data Exchange (ETDEWEB)

Shephard, Eugene; Walter, Nelson; Downey, Heath [AMEC, Inc., Portland, Maine (United States); Collopy, Peter [AMEC, Inc., San Diego, California (United States); Conant, John [ABB, Inc., Windsor, Connecticut (United States)

2013-07-01

In 2009, remediation was initiated for a non-operational fuel cycle facility previously used for government contract work located in Windsor, Connecticut, USA. Radiological contaminants consisted primarily of high enriched uranium (HEU). Other radionuclides encountered in relatively minor amounts in certain areas of the clean-up included Co-60, Cs- 137, Ra-226, Th-232 and low enriched uranium (LEU).Between 2009 and the spring of 2011, remediation efforts were focused on demolition of contaminated buildings and removal of contaminated soil. In the late spring of 2011, the last phase of remediation commenced involving the removal of contaminated sediments from portions of a 1,200 meter long gaining stream. Planning and preparation for remediation of the stream began in 2009 with submittal of permit applications to undertake construction activities in a wetland area. The permitting process was lengthy and involved securing permits from multiple agencies. However, early and frequent communication with stakeholders played an integral role in efficiently obtaining the permit approvals. Frequent communication with stakeholders throughout the planning and remediation process also proved to be a key factor in timely completion of the project. The remediation of the stream involved the use of temporary bladder berms to divert surface water flow, water diversion piping, a sediment vacuum removal system, excavation of sediments using small front-end loaders, sediment dewatering, and waste packaging, transportation and disposal. Many safeguards were employed to protect several species of concern in the work area, water management during project activities, challenges encountered during the project, methods of Final Status Survey, and stream restoration. (authors)

7 CFR 1944.419 - Final grantee evaluation.

Science.gov (United States)

2010-01-01

...) PROGRAM REGULATIONS (CONTINUED) HOUSING Self-Help Technical Assistance Grants § 1944.419 Final grantee...HA or its successor agency under Public Law 103-354 employees or an organization under contract to Fm... determine how successful the grantee was in meeting goals and objectives as defined in the agreement...

Determining the sources of fine-grained sediment using the Sediment Source Assessment Tool (Sed_SAT)

Science.gov (United States)

Gorman Sanisaca, Lillian E.; Gellis, Allen C.; Lorenz, David L.

2017-07-27

A sound understanding of sources contributing to instream sediment flux in a watershed is important when developing total maximum daily load (TMDL) management strategies designed to reduce suspended sediment in streams. Sediment fingerprinting and sediment budget approaches are two techniques that, when used jointly, can qualify and quantify the major sources of sediment in a given watershed. The sediment fingerprinting approach uses trace element concentrations from samples in known potential source areas to determine a clear signature of each potential source. A mixing model is then used to determine the relative source contribution to the target suspended sediment samples.The computational steps required to apportion sediment for each target sample are quite involved and time intensive, a problem the Sediment Source Assessment Tool (Sed_SAT) addresses. Sed_SAT is a user-friendly statistical model that guides the user through the necessary steps in order to quantify the relative contributions of sediment sources in a given watershed. The model is written using the statistical software R (R Core Team, 2016b) and utilizes Microsoft Access® as a user interface but requires no prior knowledge of R or Microsoft Access® to successfully run the model successfully. Sed_SAT identifies outliers, corrects for differences in size and organic content in the source samples relative to the target samples, evaluates the conservative behavior of tracers used in fingerprinting by applying a “Bracket Test,” identifies tracers with the highest discriminatory power, and provides robust error analysis through a Monte Carlo simulation following the mixing model. Quantifying sediment source contributions using the sediment fingerprinting approach provides local, State, and Federal land management agencies with important information needed to implement effective strategies to reduce sediment. Sed_SAT is designed to assist these agencies in applying the sediment fingerprinting

A survey of 137Cs in sediments of the eastern mediterranean marine environment from the pre-Chernobyl age to the present

International Nuclear Information System (INIS)

Evangeliou, Nikolaos; Florou, Heleny; Kritidis, Panayotis

2014-01-01

A survey of 137 Cs in sediments from the eastern Mediterranean Sea (Aegean and Ionian Seas) during the period from 1984 to 2007 is presented. Data have been collected and analyzed in the framework of the monitoring system of Greece performed by the Environmental Radioactivity Laboratory (NCSR 'Demokritos') over the past 30 years. Sediment activities reflect the impact from the Chernobyl accident one year later (1987). It is evident that sediment acts as the final receptor of 137 Cs, showing that fast depollution of the Mediterranean still remains a utopia. Radioactive 'hot spots' were observed in the northern Aegean Sea and lower values in the southern Aegean Sea and Ionian Sea. Finally, an effort to evaluate the risk of ionizing radiation (from 137 Cs) to the biota inhabiting sediments was made using ERICA. The respective dose rates for two reference organisms (benthic fish and mollusks) were estimated to be far below the screening dose, at which the radiological impact on the abundance of the population begins. (authors)

Mapping of pollutants in sediments of the German Wadden Sea - June, 1989 to June, 1992. Final report January 1993

International Nuclear Information System (INIS)

Koopmann, C.; Faller, J.; Bernem, K.H. van; Prange, A.; Mueller, A.

1994-01-01

From June 1989 to June 1992 a mapping of inorganic and organic pollutants in the sediments from the entire German Wadden Sea has been carried out. Following the guidelines of the national (Bund/Laender-Messprogramm) and international monitoring programmes for the North Sea (Joint Monitoring Programme) distribution patterns of pollutants according to their type and concentration have been determined in the course of this investigation and the main pollution areas have been established. Based on the results of the mapping of pollutants, as well as on the first findings of the biological mapping, a concept for the monitoring of pollutants in eulittoral sediments of the German Wadden Sea has been developed. (orig.) [de

Modern limnology, sediment accumulation and varve formation processes in Lake Żabińskie, northeastern Poland: comprehensive process studies as a key to understand the sediment record

Directory of Open Access Journals (Sweden)

Alicja Bonk

2014-12-01

Full Text Available Reconstructions of paleoclimatic and paleoenvironmental data from sediment records require a thorough knowledge of the physical, chemical and biological factors that influence sediment-formation processes and signal preservation in lake sediments. Lake Żabińskie, an eutrophic hardwater lake located in northeastern Poland (Masurian Lake District, provides an unique environment for the investigation of processes that lead to the varve formation. During a two-year long observation period we investigated limnological and hydrochemical conditions within the water column, recent sediment fluxes and laminations preserved in the sediments of this lake to understand the relationship between the lake water properties and the sediment formation processes. We demonstrate that different mixing patterns may occur in Lake Żabińskie, from dimictic to meromictic depending on the meteorological conditions. Regardless of the water mixing pattern, the lake was stratified during much of the year which led to significant differences between surface and near-bottom water environments. The hypolimnion was characterized by higher conductivity and anoxic conditions with only short periods of better oxygenation, which created conditions ideal for the formation and preservation of biogenic varves. The material collected from the sediment trap revealed notable changes in sediment fluxes with characteristic spring maxima and, optionally, a second late fall maxima. Considerable variability was also observed for the fluxes of total organic carbon, biogenic silica and calcite. Microscopic investigation of the topmost sediments revealed a complex structure of the varves showing a distinct spring calcite lamina followed by several fine calcite laminae interbedded with diatom-rich laminae and, finally, by an organic-rich lamina with minerogenic admixtures deposited during winter. This seasonal variability was also reflected in the chemical composition inferred from high

78 FR 41304 - Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments; Correction

Science.gov (United States)

2013-07-10

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 105 [Docket No. USCG-2013-0397] RIN 1625-AC06 Navigation and Navigable Waters; Technical, Organizational, and Conforming Amendments; Correction AGENCY: Coast Guard, DHS. ACTION: Final rule; correction. SUMMARY: The Coast Guard published a final rule...

Global Paleobathymetry Reconstruction with Realistic Shelf-Slope and Sediment Wedge

Science.gov (United States)

Goswami, A.; Hinnov, L. A.; Gnanadesikan, A.; Olson, P.

2013-12-01

bathymetry, starting with age of the oceanic crust. We then reconstructed paleobathymetry for PETM (55 Ma) and Cenomanian-Turonian (90 Ma) times. For each case, the final products are: a) a global depth to basement measurement map based on plate model and EarthByte published age of the ocean crust for modern world; b) global oceanic crust bathymetry maps with a multilayer sediment layer (two versions with two types of sediment layers based on: i) observed total sediment thickness of the modern oceans and marginal seas, and ii) EarthByte-estimated global sediment data for 00 Ma); c) global oceanic bathymetry maps (two versions with two types of sediment layers) with reconstructed shelf and slope; and d) global elevation-bathymetry maps (two versions with two types of sediment layers) with continental elevations (PALEOMAP) and ocean bathymetry. Similar maps for other geological times can be produced using this method provided that ocean crustal age is known.

The behavioural characteristics of sediment properties and their implications for sediment fingerprinting as an approach for identifying sediment sources in river basins

Science.gov (United States)

Koiter, A. J.; Owens, P. N.; Petticrew, E. L.; Lobb, D. A.

2013-10-01

Sediment fingerprinting is a technique that is increasingly being used to improve the understanding of sediment dynamics within river basins. At present, one of the main limitations of the technique is the ability to link sediment back to their sources due to the non-conservative nature of many of the sediment properties. The processes that occur between the sediment source locations and the point of collection downstream are not well understood or quantified and currently represent a black-box in the sediment fingerprinting approach. The literature on sediment fingerprinting tends to assume that there is a direct connection between sources and sinks, while much of the broader environmental sedimentology literature identifies that numerous chemical, biological and physical transformations and alterations can occur as sediment moves through the landscape. The focus of this paper is on the processes that drive particle size and organic matter selectivity and biological, geochemical and physical transformations and how understanding these processes can be used to guide sampling protocols, fingerprint selection and data interpretation. The application of statistical approaches without consideration of how unique sediment fingerprints have developed and how robust they are within the environment is a major limitation of many recent studies. This review summarises the current information, identifies areas that need further investigation and provides recommendations for sediment fingerprinting that should be considered for adoption in future studies if the full potential and utility of the approach are to be realised.

Development of Molten-Salt Heat Transfer Fluid Technology for Parabolic Trough Solar Power Plants - Public Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Grogan, Dylan C. P.

2013-08-15

Executive Summary This Final Report for the "Development of Molten-Salt Heat Transfer Fluid (HTF) Technology for Parabolic Trough Solar Power Plants” describes the overall project accomplishments, results and conclusions. Phase 1 analyzed the feasibility, cost and performance of a parabolic trough solar power plant with a molten salt heat transfer fluid (HTF); researched and/or developed feasible component options, detailed cost estimates and workable operating procedures; and developed hourly performance models. As a result, a molten salt plant with 6 hours of storage was shown to reduce Thermal Energy Storage (TES) cost by 43.2%, solar field cost by 14.8%, and levelized cost of energy (LCOE) by 9.8% - 14.5% relative to a similar state-of-the-art baseline plant. The LCOE savings range met the project’s Go/No Go criteria of 10% LCOE reduction. Another primary focus of Phase 1 and 2 was risk mitigation. The large risk areas associated with a molten salt parabolic trough plant were addressed in both Phases, such as; HTF freeze prevention and recovery, collector components and piping connections, and complex component interactions. Phase 2 analyzed in more detail the technical and economic feasibility of a 140 MWe,gross molten-salt CSP plant with 6 hours of TES. Phase 2 accomplishments included developing technical solutions to the above mentioned risk areas, such as freeze protection/recovery, corrosion effects of applicable molten salts, collector design improvements for molten salt, and developing plant operating strategies for maximized plant performance and freeze risk mitigation. Phase 2 accomplishments also included developing and thoroughly analyzing a molten salt, Parabolic Trough power plant performance model, in order to achieve the project cost and performance targets. The plant performance model and an extensive basic Engineering, Procurement, and Construction (EPC) quote were used to calculate a real levelized cost of energy (LCOE) of 11.50�

Sediment impacts on marine sponges.

Science.gov (United States)

Bell, James J; McGrath, Emily; Biggerstaff, Andrew; Bates, Tracey; Bennett, Holly; Marlow, Joseph; Shaffer, Megan

2015-05-15

Changes in sediment input to marine systems can influence benthic environments in many ways. Sponges are important components of benthic ecosystems world-wide and as sessile suspension feeders are likely to be impacted by changes in sediment levels. Despite this, little is known about how sponges respond to changes in settled and suspended sediment. Here we review the known impacts of sedimentation on sponges and their adaptive capabilities, whilst highlighting gaps in our understanding of sediment impacts on sponges. Although the literature clearly shows that sponges are influenced by sediment in a variety of ways, most studies confer that sponges are able to tolerate, and in some cases thrive, in sedimented environments. Critical gaps exist in our understanding of the physiological responses of sponges to sediment, adaptive mechanisms, tolerance limits, and the particularly the effect of sediment on early life history stages. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sediment Capping and Natural Recovery, Contaminant Transport Fundamentals With Applications to Sediment Caps

National Research Council Canada - National Science Library

Petrovski, David M; Corcoran, Maureen K; May, James H; Patrick, David M

2005-01-01

Engineered sediment caps and natural recovery are in situ remedial alternatives for contaminated sediments, which consist of the artificial or natural placement of a layer of material over a sediment...

Development of a Foam OTEC System. Final technical report for Fiscal Year 1979

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

Research on Development of a Foam OTEC System, as carried out at Carnegie-Mellon University from October 1, 1978 through September 30, 1979, is described. To a brief section summarizing highlights of research results are appended 12 technical reports which detail specific sections of the program. The work described is continuing and a proposal is currently being submitted to provide support in fiscal 1980.

An Analytic Equation Partitioning Climate Variation and Human Impacts on River Sediment Load

Science.gov (United States)

Zhang, J.; Gao, G.; Fu, B.

2017-12-01

Spatial or temporal patterns and process-based equations could co-exist in hydrologic model. Yet, existing approaches quantifying the impacts of those variables on river sediment load (RSL) changes are found to be severely limited, and new ways to evaluate the contribution of these variables are thus needed. Actually, the Newtonian modeling is hardly achievable for this process due to the limitation of both observations and knowledge of mechanisms, whereas laws based on the Darwinian approach could provide one component of a developed hydrologic model. Since that streamflow is the carrier of suspended sediment, sediment load changes are documented in changes of streamflow and suspended sediment concentration (SSC) - water discharge relationships. Consequently, an analytic equation for river sediment load changes are proposed to explicitly quantify the relative contributions of climate variation and direct human impacts on river sediment load changes. Initially, the sediment rating curve, which is of great significance in RSL changes analysis, was decomposed as probability distribution of streamflow and the corresponding SSC - water discharge relationships at equally spaced discharge classes. Furthermore, a proposed segmentation algorithm based on the fractal theory was used to decompose RSL changes attributed to these two portions. Additionally, the water balance framework was utilized and the corresponding elastic parameters were calculated. Finally, changes in climate variables (i.e. precipitation and potential evapotranspiration) and direct human impacts on river sediment load could be figured out. By data simulation, the efficiency of the segmentation algorithm was verified. The analytic equation provides a superior Darwinian approach partitioning climate and human impacts on RSL changes, as only data series of precipitation, potential evapotranspiration and SSC - water discharge are demanded.

The role of certain infauna and vascular plants in the mediation of redox reactions in marine sediments

Science.gov (United States)

Hines, Mark E.

1992-01-01

The mechanisms by which certain animals and plants affect redox processes in sediments was examined by studying three environments: (1) subtidal sediments dominated by the deposit-feeding polychaete Heteromastus filiformis; (2) a saltmarsh inhabited by the tall form of Spartina alterniflora; and (3) tropical carbonate sediments inhabited by three species of seagrasses. S-35-sulfide production rates were compared to pool sizes of dissolved sulfide and dissolved iron. In all of the sediments studied, rates of sulfide reduction were enhanced by macroorganisms while the rate of turnover of dissolved sulfide increased. The polychaete enhanced microbial activity and redox cycling primarily by subducting particles of organic matter and oxidized iron during sediment reworking. The Spartina species enhanced anaerobic activity by transporting primarily dissolved organic matter and oxidants. Although the final result of both animal and plant activities was the enhancement of sub-surface cycling of sulfur and iron, decreased dissolved sulfide and increased dissolved iron concentrations, the mechanisms which produced these results differed dramatically.

Fluvial sediment transport: Analytical techniques for measuring sediment load

International Nuclear Information System (INIS)

2005-07-01

Sediment transport data are often used for the evaluation of land surface erosion, reservoir sedimentation, ecological habitat quality and coastal sediment budgets. Sediment transport by rivers is usually considered to occur in two major ways: (1) in the flow as a suspended load and (2) along the bed as a bed load. This publication provides guidance on selected techniques for the measurement of particles moving in both modes in the fluvial environment. The relative importance of the transport mode is variable and depends on the hydraulic and sedimentary conditions. The potential user is directed in the selection of an appropriate technique through the presentation of operating principles, application guidelines and estimated costs. Techniques which require laboratory analysis are grab sample, pump sample, depth sample, point integrated and radioactive tracers. Techniques which will continuously record data are optical backscattering, nuclear transmission, single frequency acoustic and laser diffraction

Final Technical Report. DeepCwind Consortium Research Program. January 15, 2010 - March 31, 2013

Energy Technology Data Exchange (ETDEWEB)

Dagher, Habib [Univ. of Maine, Orono, ME (United States); Viselli, Anthony [Univ. of Maine, Orono, ME (United States); Goupee, Andrew [Univ. of Maine, Orono, ME (United States); Thaler, Jeffrey [Univ. of Maine, Orono, ME (United States); Brady, Damian [Univ. of Maine, Orono, ME (United States); Browne, Peter [HDR, Inc., Omaha, NE (United States); Browning, James [Univ. of Colorado, Boulder, CO (United States); Chung, Jade [Univ. of Maine, Orono, ME (United States); Coulling, Alexander [Univ. of Maine, Orono, ME (United States); Deese, Heather [Island Institute, Rockland, ME (United States); Fowler, Matthew [Univ. of Maine, Orono, ME (United States); Holberton, Rebecca [Univ. of Maine, Orono, ME (United States); Anant, Jain [Intertek, Duluth, GA (United States); Jalbert, Dustin [Univ. of Maine, Orono, ME (United States); Johnson, Theresa [Univ. of Maine, Orono, ME (United States); Jonkman, Jason [National Renewable Energy Laboratory, Golden, CO (United States); Karlson, Benjamin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kimball, Richard [Maine Maritime Academy, Castine, ME (United States); Koo, Bonjun [Technip, Paris (France); Lackner, Matthew [Univ. of Massachusetts, Amherst, MA (United States); Lambrakos, Kostas [Technip, Paris (France); Lankowski, Matthew [Univ. of Maine, Orono, ME (United States); Leopold, Adrienne [Univ. of Maine, Orono, ME (United States); Lim, Ho-Joon [Technip, Paris (France); Mangum, Linda [Univ. of Maine, Orono, ME (United States); Martin, Heather [Univ. of Maine, Orono, ME (United States); Masciola, Marco [National Renewable Energy Laboratory, Golden, CO (United States); Maynard, Melissa [Univ. of Maine, Orono, ME (United States); McCleave, James [Univ. of Maine, Orono, ME (United States); Mizrahi, Robert [New Jersey Audubon Society, Bernardsville, NJ (United States); Molta, Paul [National Renewable Energy Laboratory, Golden, CO (United States); Pershing, Andrew [Gulf of Maine Research Institute, Portland, ME (United States); Pettigrew, Neal [Univ. of Maine, Orono, ME (United States); Prowell, Ian [MMI Engineering, Oakland, CA (United States); Qua, Andrew [Kleinschmidt Associates, Pittsfield, ME (United States); Sherwood, Graham [Gulf of Maine Research Institute, Portland, ME (United States); Snape, Thomas [Univ. of Maine, Orono, ME (United States); Steneck, Robert [Univ. of Maine, Orono, ME (United States); Stewart, Gordon [Univ. of Massachusetts, Amherst, MA (United States); Stockwell, Jason [Gulf of Maine Research Institute, Portland, ME (United States); Swift, Andrew H. P. [Texas Tech Univ., Lubbock, TX (United States); Thomas, Dale [Maine Maritime Academy, Castine, ME (United States); Viselli, Elizabeth [Univ. of Maine, Orono, ME (United States); Zydlewski, Gayle [Univ. of Maine, Orono, ME (United States)

2013-06-11

This is the final technical report for the U.S. Department of Energy-funded program, DE-0002981: DeepCwind Consortium Research Program. The project objective was the partial validation of coupled models and optimization of materials for offshore wind structures. The United States has a great opportunity to harness an indigenous abundant renewable energy resource: offshore wind. In 2010, the National Renewable Energy Laboratory (NREL) estimated there to be over 4,000 GW of potential offshore wind energy found within 50 nautical miles of the US coastlines (Musial and Ram, 2010). The US Energy Information Administration reported the total annual US electric energy generation in 2010 was 4,120 billion kilowatt-hours (equivalent to 470 GW) (US EIA, 2011), slightly more than 10% of the potential offshore wind resource. In addition, deep water offshore wind is the dominant US ocean energy resource available comprising 75% of the total assessed ocean energy resource as compared to wave and tidal resources (Musial, 2008). Through these assessments it is clear offshore wind can be a major contributor to US energy supplies. The caveat to capturing offshore wind along many parts of the US coast is deep water. Nearly 60%, or 2,450 GW, of the estimated US offshore wind resource is located in water depths of 60 m or more (Musial and Ram, 2010). At water depths over 60 m building fixed offshore wind turbine foundations, such as those found in Europe, is likely economically infeasible (Musial et al., 2006). Therefore floating wind turbine technology is seen as the best option for extracting a majority of the US offshore wind energy resource. Volume 1 - Test Site; Volume 2 - Coupled Models; and Volume 3 - Composite Materials

Modeling chemical accumulation in sediment of small waterbodies accounting for sediment transport and water-sediment exchange processes over long periods.

Science.gov (United States)

Patterson, David Albert; Strehmel, Alexander; Erzgräber, Beate; Hammel, Klaus

2017-12-01

In a recent scientific opinion of the European Food Safety Authority it is argued that the accumulation of plant protection products in sediments over long time periods may be an environmentally significant process. Therefore, the European Food Safety Authority proposed a calculation to account for plant protection product accumulation. This calculation, however, considers plant protection product degradation within sediment as the only dissipation route, and does not account for sediment dynamics or back-diffusion into the water column. The hydraulic model Hydrologic Engineering Center-River Analysis System (HEC-RAS; US Army Corps of Engineers) was parameterized to assess sediment transport and deposition dynamics within the FOrum for Co-ordination of pesticide fate models and their USe (FOCUS) scenarios in simulations spanning 20 yr. The results show that only 10 to 50% of incoming sediment would be deposited. The remaining portion of sediment particles is transported across the downstream boundary. For a generic plant protection product substance this resulted in deposition of only 20 to 50% of incoming plant protection product substance. In a separate analysis, the FOCUS TOXSWA model was utilized to examine the relative importance of degradation versus back-diffusion as loss processes from the sediment compartment for a diverse range of generic plant protection products. In simulations spanning 20 yr, it was shown that back-diffusion was generally the dominant dissipation process. The results of the present study show that sediment dynamics and back-diffusion should be considered when calculating long-term plant protection product accumulation in sediment. Neglecting these may lead to a systematic overestimation of accumulation. Environ Toxicol Chem 2017;36:3223-3231. © 2017 SETAC. © 2017 SETAC.

Evaluating Regime Change of Sediment Transport in the Jingjiang River Reach, Yangtze River, China

Directory of Open Access Journals (Sweden)

Li He

2018-03-01

Full Text Available The sediment regime in the Jingjiang river reach of the middle Yangtze River has been significantly changed from quasi-equilibrium to unsaturated since the impoundment of the Three Gorges Dam (TGD. Vertical profiles of suspended sediment concentration (SSC and sediment flux can be adopted to evaluate the sediment regime at the local and reach scale, respectively. However, the connection between the vertical concentration profiles and the hydrologic conditions of the sub-saturated channel has rarely been examined based on field data. Thus, vertical concentration data at three hydrological stations in the reach (Zhicheng, Shashi, and Jianli are collected. Analyses show that the near-bed concentration (within 10% of water depth from the riverbed may reach up to 15 times that of the vertical average concentration. By comparing the fractions of the suspended sediment and bed material before and after TGD operation, the geomorphic condition under which the distinct large near-bed concentrations occur have been examined. Based on daily discharge-sediment hydrographs, the reach scale sediment regime and availability of sediment sources are analyzed. In total, remarkable large near-bed concentrations may respond to the combination of wide grading suspended particles and bed material. Finally, several future challenges caused by the anomalous vertical concentration profiles in the unsaturated reach are discussed. This indicates that more detailed measurements or new measuring technologies may help us to provide accurate measurements, while a fractional dispersion equation may help us in describing. The present study aims to gain new insights into regime change of sediment suspension in the river reaches downstream of a very large reservoir.

Conceptual model of sediment processes in the upper Yuba River watershed, Sierra Nevada, CA

Science.gov (United States)

Curtis, J.A.; Flint, L.E.; Alpers, Charles N.; Yarnell, S.M.

2005-01-01

This study examines the development of a conceptual model of sediment processes in the upper Yuba River watershed; and we hypothesize how components of the conceptual model may be spatially distributed using a geographical information system (GIS). The conceptual model illustrates key processes controlling sediment dynamics in the upper Yuba River watershed and was tested and revised using field measurements, aerial photography, and low elevation videography. Field reconnaissance included mass wasting and channel storage inventories, assessment of annual channel change in upland tributaries, and evaluation of the relative importance of sediment sources and transport processes. Hillslope erosion rates throughout the study area are relatively low when compared to more rapidly eroding landscapes such as the Pacific Northwest and notable hillslope sediment sources include highly erodible andesitic mudflows, serpentinized ultramafics, and unvegetated hydraulic mine pits. Mass wasting dominates surface erosion on the hillslopes; however, erosion of stored channel sediment is the primary contributor to annual sediment yield. We used GIS to spatially distribute the components of the conceptual model and created hillslope erosion potential and channel storage models. The GIS models exemplify the conceptual model in that landscapes with low potential evapotranspiration, sparse vegetation, steep slopes, erodible geology and soils, and high road densities display the greatest hillslope erosion potential and channel storage increases with increasing stream order. In-channel storage in upland tributaries impacted by hydraulic mining is an exception. Reworking of stored hydraulic mining sediment in low-order tributaries continues to elevate upper Yuba River sediment yields. Finally, we propose that spatially distributing the components of a conceptual model in a GIS framework provides a guide for developing more detailed sediment budgets or numerical models making it an

Beowawe Bottoming Binary Unit - Final Technical Report for EE0002856

Energy Technology Data Exchange (ETDEWEB)

McDonald, Dale Edward

2013-02-12

This binary plant is the first high-output refrigeration based waste heat recovery cycle in the industry. Its working fluid is environmentally friendly and as such, the permits that would be required with a butane based cycle are not necessary. The unit is modularized, meaning that the unit’s individual skids were assembled in another location and were shipped via truck to the plant site. This project proves the technical feasibility of using low temperature brine The development of the unit led to the realization of low temperature, high output, and environmentally friendly heat recovery systems through domestic research and engineering. The project generates additional renewable energy for Nevada, resulting in cleaner air and reduced carbon dioxide emissions. Royalty and tax payments to governmental agencies will increase, resulting in reduced financial pressure on local entities. The major components of the unit were sourced from American companies, resulting in increased economic activity throughout the country.

Microscale ecotoxicity testing of Moselle river watershed (Lorraine Province, France sediments

Directory of Open Access Journals (Sweden)

Jean François Férard

2015-06-01

Full Text Available The ecotoxic potential of seven Moselle river watershed sediments was assessed with a battery of bioassays comprised of rapid phototrophic [LuminoTox solid phase (L-SPA and elutriate (L-ELU assays] and bacterial [Microtox solid phase assay (M-SPA] exposure tests, as well as with two micro-invertebrate solid phase tests conducted with Hydra attenuata (lethal and sublethal effects solid phase assay, HL-SPA and HSL-SPA and Chironomus riparius. Measured effects of sediments and their elutriates were varied and reflected responses that were ecotoxicity test-, endpoint- and site-dependent, suggesting some degree of risk toward benthic and water column organisms, respectively, at specific sites. Correlation analysis demonstrated that L-SPA and M-SPA ecotoxicity responses were significantly linked with the Hydra HSL-SPA assay, indicating their ability to predict ecotoxicity towards an invertebrate taxonomic group representing secondary consumers. While the L-SPA and M-SPA assays hold promise as rapid screens for sediment ecotoxicity, correlation analysis with grain size (L-SPA: r=-0.795, P=0.033; M-SPA: r=-0.73, P=0.07 points out that their responses can be influenced by the presence of fines (i.e., sediment particles ≤0.063 mm in size and that this information is essential to properly interpret ecotoxicity data generated with these assays. Finally, notable differences observed in trophic level sensitivities once again recall the importance of employing a test battery to adequately appraise the ecotoxicity of sediments.

Inferring sediment connectivity from high-resolution DEMs of Difference

Science.gov (United States)

Heckmann, Tobias; Vericat, Damià

2017-04-01

) erosion and deposition has emerged from sediment transfer between the two epochs of the DoD (i.e. functional connectivity). In this study, we use multitemporal raster DEMs generated (i) from terrestrial LiDAR surveys and (ii) by a landscape evolution model to compute DoDs. Flow accumulation is used to compute, for the contributing area of each raster cell, (i) the net balance and (ii) the total sum of material eroded. The net balance represents the sediment yield of the contributing area. In the case of a study area delimited by a catchment boundary, it is either negative (more sediment eroded than deposited within the contributing area, i.e. net export) or zero (eroded material has been re-deposited within the contributing area). Finally, the ratio of sediment yield and gross erosion is called the sediment delivery ratio (SDR). This number has been used as a "performance factor" indicating the degree of sediment connectivity, as it describes the proportion of material eroded on the local scale that is being delivered to the outlet of the contributing area. The evaluation of a DoD to compute the SDR overcomes one major criticism of the SDR, namely that gross erosion is generally estimated (e.g. by empirical USLE-type equations) rather than measured. Both our proposed approach and the concept of SDR are subject to a number of caveats, which we will discuss in our contribution. In any case, we advocate more detailed analyses of DoD using flow routing algorithms in order to include information on potential sediment pathways in morphological sediment budgets for hillslopes and catchments.

Total and species-specific quantitative analyses of trace elements in sediment by isotope dilution inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Inagaki, Kazumi; Takatsu, Akiko; Yarita, Takashi; Okamoto, Kensaku; Chiba, Koichi

2009-01-01

Isotope dilution inductively coupled plasma mass spectrometry (ID-ICP-MS) is one of the reliable methods for total and species-specific quantitative analysis of trace elements. However, several technical problems (e.g. spectral interference caused from sample constituents) should be overcome to obtain reliable analytical results when environmental samples are analyzed by ID-ICP-MS. In our laboratory, various methods based on ID-ICP-MS have been investigated for reliable quantitative analyses of trace elements in environmental samples. In this paper, coprecipitate separation/ID-ICP-MS for the determination of trace elements in sediment, cation exchange disk filtration/ID-ICP-MS for the determination of selenium in sediment, species-specific ID-ICP-MS using 118 Sn/labeled organotin compounds for the determination of butyltins and phenyltins, and the application of the ID-ICP-MS methods to the certification of sediment reference materials are described. (author)

Review on utilization of biochar for metal-contaminated soil and sediment remediation.

Science.gov (United States)

Wang, Mingming; Zhu, Yi; Cheng, Lirong; Andserson, Bruce; Zhao, Xiaohui; Wang, Dayang; Ding, Aizhong

2018-01-01

Biochar is a carbon-neutral or even carbon-negative material produced through thermal decomposition of plant- and animal-based biomass under oxygen-limited conditions. Recently, there has been an increasing interest in the application of biochar as an adsorbent, soil ameliorant and climate mitigation approach in many types of applications. Metal-contaminated soil remediation using biochar has been intensively investigated in small-scale and pilot-scale trials with obtained beneficial results and multifaceted effects. But so far, the study and application of biochar in contaminated sediment management has been very limited, and this is also a worldwide problem. Nonetheless, there is reason to believe that the same multiple benefits can also be realized with these sediments due to similar mechanisms for stabilizing contaminants. This paper provides a review on current biochar properties and its use as a sorbent/amendment for metal-contaminated soil/sediment remediation and its effect on plant growth, fauna habits as well as microorganism communities. In addition, the use of biochar as a potential strategy for contaminated sediment management is also discussed, especially as regards in-situ planning. Finally, we highlight the possibility of biochar application as an effective amendment and propose further research directions to ensure the safe and sustainable use of biochar as an amendment for remediation of contaminated soil and sediment. Copyright © 2017. Published by Elsevier B.V.

Effects of sediment composition on inorganic mercury partitioning, speciation and bioavailability in oxic surficial sediments

International Nuclear Information System (INIS)

Zhong Huan; Wang Wenxiong

2008-01-01

Artificially prepared sediments were used to assess the effects of sediment composition on inorganic Hg partitioning, speciation and bioavailability. Organic coating in sediment greatly increased the Hg partitioning and the amount of bioavailable Hg bound with the clay and the Fe and Mn oxides, but had little effect on that bound with the quartz and calcium carbonate as a result of weaker binding of humic acids and fulvic acids. The clay content increased the concentration of Hg in the sediments but inhibited the gut juice extraction due to the strong binding of Hg-organic matter (OM) complexes. Most Hg in the sediments was complexed by OM (mainly distributed in the organo-complexed phase and the strongly complexed phase), and the Hg-OM complexes (especially Hg in the strongly complexed phase) in sediments contributed much to gut juice extraction. Redistribution of Hg-OM complexes between sediments and gut juices may occur during gut juice extraction and modify Hg bioavailability and speciation in sediments. - Organic and clay contents in sediments are the two most important components controlling Hg partitioning in sediments and bioavailability

Sediment Transport Capacity of Turbidity Currents: from Microscale to Geological Scale.

Science.gov (United States)

Eggenhuisen, J. T.; Tilston, M.; Cartigny, M.; Pohl, F.; de Leeuw, J.; van der Grind, G. J.

2016-12-01

A big question in sedimentology concerns the magnitude of fluxes of sediment particles, solute matter and dissolved gasses from shallow marine waters to deep basins by turbidity current flow. Here we establish sediment transport capacity of turbidity current flow on three levels. The most elementary level is set by the maximum amount of sediment that can be contained at the base of turbidity currents without causing complete extinction of boundary layer turbulence. The second level concerns the capacity in a vertical column within turbidity currents. The third level involves the amount of sediment that can be transported in turbidite systems on geological timescales. The capacity parameter Γ compares turbulent forces near the boundary of a turbulent suspension to gravity and buoyancy forces acting on suspended particles. The condition of Γ>1 coincides with complete suppression of coherent boundary layer turbulence in Direct Numerical Simulations of sediment-laden turbulent flow. Γ=1 coincides with the upper limit of observed suspended particle concentrations in flume and field measurements. Γ is grainsize independent, yet capacity of the full vertical structure of turbidity currents becomes grainsize dependent. This is due to the appearance of grainsize dependent vertical motions within turbulence as a primary control on the shape of the vertical concentration profile. We illustrate this dependence with experiments and theory and conclude that capacity depends on the competence of prevailing turbulence to suspend particle sizes. The concepts of capacity and competence are thus tangled. Finally, the capacity of turbidity current flow structure is coupled to geological constraints on recurrence times, channel and lobe life cycles, and allogenic forcing on system activity to arrive at system scale sediment transport capacity. We demonstrate a simple model that uses the fundamental process insight described above to estimate geological sediment budgets from

Significance of antifouling paint flakes to the distribution of dichlorodiphenyltrichloroethanes (DDTs) in estuarine sediment

International Nuclear Information System (INIS)

Wu, Chen-Chou; Bao, Lian-Jun; Tao, Shu; Zeng, Eddy Y.

2016-01-01

Recently published literature indicated that dichlorodiphenyltrichloroethane (DDT)-containing antifouling paint flakes were heterogeneously distributed within estuarine sediments. However, the significance of antifouling paint flakes in the fate and transport of DDT compounds and other organic pollutants in estuarine sediment is yet to be adequately addressed. To fill this knowledge gap, estuarine sediment and paint flakes from cabin and boat surfaces were collected from a fishery base in Guangdong Province of South China and analyzed for DDT compounds. Coarse fractioned samples collected from the vicinity of boat maintenance facilities contained appreciable amounts of colorful particles, which were identified as paint flakes by Fourier transform infrared spectroscopy. The highest concentrations of DDXs (sum of DDTs and its metabolites) occurred in the heavy-density (>1.7 g cm"−"3) fraction of coarse-size (200–2000 μm) sediments from near the boat maintenance facilities, suggesting the importance of paint flakes in the distribution pattern of “hot spots” in estuarine sediment. Moreover, the desorption rates of DDT compounds from paint flakes and the heavy-density fraction of coarse-size sediment were both extremely slow. Apparently, unevenly distributed paint flakes in sediment can artificially inflate the sorption capacity of heavy-density sediment for DDT compounds, and therefore can substantially change the environmental fate and behavior of hydrophobic organic chemicals in estuarine sediment. Finally, commonly used source diagnostic indices of DDT compounds were mostly grain-size and density dependent in sediment, as a result of the occurrence of paint flakes, which may strongly compromise the outcome of any source diagnostics efforts. - Highlights: • Concentrations of DDTs were elevated in coarse and high-density fractions. • The desorption rates of DDTs from coarse and high-density fraction were extreme slow. • DDTs-containing antifouling

[Limnology of high mountain tropical lake, in Ecuador: characteristics of sediments and rate of sedimentation].

Science.gov (United States)

Gunkel, Günter

2003-06-01

Equatorial high mountain lakes are a special type of lake occurring mainly in the South American Andes as well as in Central Africa and Asia. They occur at altitudes of a few thousand meters above sea level and are cold-water lakes (limnological study was therefore undertaken at Lake San Pablo, Ecuador, to analyze the basic limnological processes of the lake, which has a tendency for eutrophication. Sediment quality of San Pablo Lake is given under consideration of horizontal and vertical distribution using sediment cores. Significance of sediments for eutrophication process of lakes is demonstrated using phosphorus concentration of sediments as well as the phosphorus retention capacity of the sediments by ratio Fe/P. Dating of the sediments is done using 137Cs and 210Pb, but the activity of 137Cs in the sediment was very low nearly at the detection level. Sedimentation rate is determined to be 3.5 mm/year and the sediment cores represent about 110 years. P concentration of the sediments is high (approximately 5 g/kg dry substance), and P retention capacity by Fe is insufficient (Fe/P = 4). The sediment quality did not change significantly during the past decades, and the trophic state of San Pablo Lake was already less or more eutrophic 110 years ago. The contamination of the lake sediments by heavy metals is insignificant.

Nickel, Lead and Zinc Contamination in the Surface Sediments of Agh Gel Wetland, Iran

Directory of Open Access Journals (Sweden)

Soheil Sobhan Ardakani

2016-07-01

Full Text Available Background & Aims of the Study: Due to the increased human activities around the Agh Gel wetland, this study aimed to measured accumulations of heavy metals (Ni, Pb and Zn in the surface sediment samples taken from this wetland. Materials & Methods: Samples were taken from 10 stations and exposed to bulk digestion and chemical partitioning. Finally, Ni, Pb and Zn concentrations were monitored with ICP-OES in the sediments. Also, geo-accumulation index, contamination factor and pollution load index were used to evaluate the magnitude of contaminants in the sediment profile. Results: The results showed, the average of metal concentration in samples (mg kg-1 wet weight were 34.20±3.58 for Ni, 25.37±2.52 for Pb and 127.20±15.21 for Zn, respectively. Therefore, the pattern of metal concentrations in sediment was determined as Zinc>Nickel >Lead. According to the mean I-geo values, sediments' qualities are classified as unpolluted category for Ni and Pb. Also, sediment's quality is classified as unpolluted to moderately polluted for Zn. The CF values for all elements are classified as moderate contamination. The PLI values indicated that metal pollution exists for all sampling stations. Conclusions: The obtained results indicated that the Agh Gel wetland has a potential to threaten by chemical pollutants such as agricultural effluent. So, in order to preserve the environment of the Agh Gel wetland from deterioration, monitoring of water and sediment qualities is recommended periodically.

Correlations of turbidity to suspended-sediment concentration in the Toutle River Basin, near Mount St. Helens, Washington, 2010-11

Science.gov (United States)

Uhrich, Mark A.; Kolasinac, Jasna; Booth, Pamela L.; Fountain, Robert L.; Spicer, Kurt R.; Mosbrucker, Adam R.

2014-01-01

Researchers at the U.S. Geological Survey, Cascades Volcano Observatory, investigated alternative methods for the traditional sample-based sediment record procedure in determining suspended-sediment concentration (SSC) and discharge. One such sediment-surrogate technique was developed using turbidity and discharge to estimate SSC for two gaging stations in the Toutle River Basin near Mount St. Helens, Washington. To provide context for the study, methods for collecting sediment data and monitoring turbidity are discussed. Statistical methods used include the development of ordinary least squares regression models for each gaging station. Issues of time-related autocorrelation also are evaluated. Addition of lagged explanatory variables was used to account for autocorrelation in the turbidity, discharge, and SSC data. Final regression model equations and plots are presented for the two gaging stations. The regression models support near-real-time estimates of SSC and improved suspended-sediment discharge records by incorporating continuous instream turbidity. Future use of such models may potentially lower the costs of sediment monitoring by reducing time it takes to collect and process samples and to derive a sediment-discharge record.

Estimating sediment and caesium-137 fluxes in the Ribble Estuary through time-series airborne remote sensing

International Nuclear Information System (INIS)

Wakefield, R.; Tyler, A.N.; McDonald, P.; Atkin, P.A.; Gleizon, P.; Gilvear, D.

2011-01-01

High spatial and temporal resolution airborne imagery were acquired for the Ribble Estuary, North West England in 1997 and 2003, to assess the application of time-series airborne remote sensing to quantify total suspended sediment and radionuclide fluxes during a flood and ebb tide sequence. Concomitant measurements of suspended particulate matter (SPM) and water column turbidity were obtained during the time-series image acquisition for the flood and ebb tide sequence on the 17th July 2003 to verify the assumption of a vertically well mixed estuary and thus justifying the vertical extrapolation of spatially integrated estimate of surface SPM. The 137 Cs activity concentrations were calculated from a relatively stable relationship between SPM and 137 Cs for the Ribble Estuary. Total estuary wide budgets of sediment and 137 Cs were obtained by combining the image-derived estimates of surface SPM and 137 Cs with estimates of water volume from a two-dimensional hydrodynamic model (VERSE) developed for the Ribble Estuary. These indicate that around 10,000 tonnes of sediment and 2.72 GBq of 137 Cs were deposited over the tidal sequence monitored in July 2003. This compared favourably with bed height elevation change estimated from field work. An uncertainty analysis on the total sediment and 137 Cs flux yielded a total budget of the order of 40% on the final estimate. The results represent a novel approach to providing a spatially integrated estimate of the total net sediment and radionuclide flux in an intertidal environment over a flood and ebb tide sequence. - Research highlights: → This paper provides a rare insight into the next flux of sediment and associated radionuclide loading into an estuary over and ebb and flood tide sequence. → The paper uses high temporal resolution airborne imagery coupled with concomitant sampling to convert total suspended sediment flux to 137 Cs loading. → For the estuary and date studied, it is estimate that an 10,000 tonnes of

Technical co-operation report for 2000. Report by the Director General

International Nuclear Information System (INIS)

2001-01-01

This report covers three separate topics. Part one fulfills the Agency's obligation under the General Conference resolution GC(44)/RES/18 to report on the Strengthening of Technical Co-operation. It covers the period from 1 April 2000 to 31 March 2001. The report examines the finalization of the 2001-2002 technical co-operation programme and several key concepts of the Technical Co-operation Strategy such as Partners in Development, Technical Co-operation among Developing Countries, and the continuing evolution of Regional Resource Centres. Reflecting an important trend in the technical co-operation programme, which was mandated by the General Conference, the report describes the results achieved in several programmes in least developed countries. Part two reports on the major achievements of the technical co-operation programme in 2000 in the different regions of the world. Part three presents a summary of the financial and non-financial parameters of the technical co-operation programme. The supplement to the report provides a more detailed review of resources and contributions, disbursements and non-financial indicators

Technical co-operation report for 2000. Report by the Director General

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This report covers three separate topics. Part one fulfills the Agency's obligation under the General Conference resolution GC(44)/RES/18 to report on the Strengthening of Technical Co-operation. It covers the period from 1 April 2000 to 31 March 2001. The report examines the finalization of the 2001-2002 technical co-operation programme and several key concepts of the Technical Co-operation Strategy such as Partners in Development, Technical Co-operation among Developing Countries, and the continuing evolution of Regional Resource Centres. Reflecting an important trend in the technical co-operation programme, which was mandated by the General Conference, the report describes the results achieved in several programmes in least developed countries. Part two reports on the major achievements of the technical co-operation programme in 2000 in the different regions of the world. Part three presents a summary of the financial and non-financial parameters of the technical co-operation programme. The supplement to the report provides a more detailed review of resources and contributions, disbursements and non-financial indicators.

The role of bacteria in the nutrient exchange between sediment and water in a flow-through system.

Science.gov (United States)

Kairesalo, T; Tuominen, L; Hartikainen, H; Rankinen, K

1995-03-01

The contribution of bacteria to phosphorus (P) and nitrogen (N ) release from, or retention in, sediment was studied in a flow-through system. "Live" and formaldehyde-"killed" sediment communities were incubated in 25-liter bottles with a continuous flow of P- or P + N-enriched water. Sediment bacteria in the killed communities were inhibited by adding formaldehyde (final concentration 0.04% v/v) to the sediment before the start of the experiment. Bacterial activity in the live sediments measured with [(3)H]thymidine and [(14)C]leucine incorporation techniques did not change essentially during the experiment period (7-8 days). Chemical mechanisms were found to be of principal importance in PO4-P retention in the sediment. In the live samples, the net retention of PO4-P was lower than in the killed samples, which was likely due to the reduced O2 conditions in the sediment as a consequence of bacterial mineralization. In total P exchange, however, bacteria increased the retention rate by recycling dissolved organic P in the sediment. In the live communities the retention of N was very efficient, and all the introduced NH4 -N and NO3-N was immobilized by sediment bacteria. Nitrogen enrichment, however, did not alter the P exchange rates. The gradual emergence of bacterial activity (and grazing) in the killed communities, subsequent to the dilution of formaldehyde concentration, enhanced the release of PO4-P and NH4-N from sediment.

75 FR 4803 - Notice of Availability of the Final Environmental Impact Statement for Decommissioning and/or...

Science.gov (United States)

2010-01-29

...). The Proposed Action includes the decontamination and decommissioning of the waste storage tanks and... site facilities identified in the Final EIS would be removed; contaminated soil, sediment, and...

Chemical and carbon isotope composition of Varzeas sediments and its interactions with some Amazon basin rivers

International Nuclear Information System (INIS)

Martinelli, L.A.

1986-01-01

Varzea sediment samples were collected on the banks of Amazon rivers and in the most important tributaires. The samples were taken in three different river stages. The major cations, pH, total nitrogen, total phosphorus, carbon and δ 13 C values were determined. The concentration of major basic cations - Ca,Mg,K e Na were greater in the main channel sediments than in the tributaires. Probably the differences in the substrats geology and erosion regimes of the basins account for this patterns, generally. The major basic cation, total phosphorus and carbon concentration were lower in the low Amazon Varzeas. Between the three differents sampling periods, pratically the elements concentration in Varzea sediment was constant. Finally, the datas showed that the most parts of Varzea carbon sediment had it's origin in the fine particulated organic matter transported by the Amazon river. (C.D.G.) [pt

Effects of experimental acidification on mobilisation of metals from sediments of limed and non-limed lakes

International Nuclear Information System (INIS)

Waellstedt, Teresia; Borg, Hans

2003-01-01

In order to study the influence of pH on the mobilisation of metals from lake sediments, intact sediment cores with overlying water were sampled from one lime treated lake and one acidified lake. The overlying water of two cores from each lake was successively acidified to pH 4.2 over a period of 3 months. In the acid treated samples from the limed lake, the initial concentrations of Al, Cd, Mn, Pb and Zn in the overlying water were generally lower and the final concentrations were higher than in the acid treated samples from the acidified lake. The labile inorganic fraction of Al (Al i ) was increasingly dominating as pH decreased. Redox potential and pH in the sediment indicated that the upper two centimetres were involved in the exchange reactions. The experiment showed that mobilisation of metals from sediments can occur and the results indicated that mobilisation could contribute to increased concentrations of metals in lake water during reacidification of formerly lime treated lakes. - Reacidification leads to mobilisation of metals from lake sediments

Long-term viability of carbon sequestration in deep-sea sediments

Science.gov (United States)

Teng, Y.; Zhang, D.

2017-12-01

Sequestration of carbon dioxide in deep-sea sediments has been proposed for the long-term storage of anthropogenic CO2, due to the negative buoyancy effect and hydrate formation under conditions of high pressure and low temperature. However, the multi-physics process of injection and post-injection fate of CO2 and the feasibility of sub-seabed disposal of CO2 under different geological and operational conditions have not been well studied. On the basis of a detailed study of the coupled processes, we investigate whether storing CO2 into deep-sea sediments is viable, efficient, and secure over the long term. Also studied are the evolution of the multiphase and multicomponent flow and the impact of hydrate formation on storage efficiency during the upward migration of the injected CO2. It is shown that low buoyancy and high viscosity slow down the ascending plume and the forming of the hydrate cap effectively reduces the permeability and finally becomes an impermeable seal, thus limiting the movement of CO2 towards the seafloor. Different flow patterns at varied time scales are identified through analyzing the mass distribution of CO2 in different phases over time. Observed is the formation of a fluid inclusion, which mainly consists of liquid CO2 and is encapsulated by an impermeable hydrate film in the diffusion-dominated stage. The trapped liquid CO2 and CO2 hydrate finally dissolve into the pore water through diffusion of the CO2 component. Sensitivity analyses are performed on storage efficiency under variable geological and operational conditions. It is found that under a deep-sea setting, CO2 sequestration in intact marine sediments is generally safe and permanent.

The Assessment of Sediment Heavy Metal Pollution in Begej Canal (Serbia)

Science.gov (United States)

Krčmar, Dejan; Trickovic, Jelena; Grba, Nenad; Becelic Tomin, Milena; Pesic, Vesna; Varga, Natasa; Dalmacija, Bozo

2016-04-01

Accumulation of heavy metals in aquatic systems has received huge concern due to their toxicity, persistence and subsequent accumulation in aquatic sediments. One of the most crucial properties of the metals, which differentiate them from organic pollutants, is that they are not biodegradable in the environment. Metals are part of biogeochemical cycles with aquatic sediments acting as their ultimate sinks for longer periods of time. However, when environmental conditions change (pH, redox potential, etc.) sediments act as secondary sources of metal pollution. The toxicity and mobility of metals depend strongly on the way they are associated with sediments. Therefore, information on the total concentrations of metals in sediment alone should not be used to assess the environmental impact of polluted sediments. The Begej Canal is navigation canal between Romania and Serbia and it is a part of Danube-Tisa-Danube hydrosystem in Vojvodina (Northern Province of Serbia). Approximately, 500,000 m3 of sediment is accumulated in Begej canal which currently prevents canal's primary function - navigability. The objective of the present study was to assess the chemical quality of Begej canal sediments regarding heavy metals content. The concentrations of heavy metals were as follows: Cd - 2.4-4.9 mg/kg, Cr - 125-349 mg/kg, Cu - 65-124 mg/kg, Pb - 47-113 mg/kg, Ni - 45-88 mg/kg and Zn - 362-602 mg/kg. According to Serbian legislation (Official gazette, no. 50/12), sediment of Begej canal is the third class sediment which means that special measures should be taken in case of its removal from watercourse and final disposal in order to prevent contamination of other environmental compartments (soil, ground waters, surface waters, wildlife). Therefore, determination of third class has important economic and social implications. Additional tests to assess sediment quality included determination of contamination factor (CF), pollution load index (PLI) and enrichment factor (EF). In

Estimating suspended sediment yield, sedimentation controls and impacts in the Mellah Catchment of Northern Algeria

International Nuclear Information System (INIS)

Khanchoul, Kamel; Assassi Fella; Altschul, Robert

2009-01-01

This paper is an assessment of the suspended sediment yield in the Mellah Catchment of northern Algeria. We use discharge-sediment load relationships to explore the variability of water discharge and sediment load, and to investigate the impact of geomorphic factors disturbance on erosion and sedimentation. Suspended sediment load was analyzed in the Mellah Catchment (550 squre kms ) which was controlled by a gauging station to measure discharge and sediment transport. The relations between daily mean sediment concentration and daily mean water discharge were analyzed to develop sediment rating curves. For storms with no water samples, a sediment rating curve was developed. The technique involves stratification of data into discharge-based classes, the mean of which are used to fit a rating curve according to single flow data and season to provide various rating relationships. The mean annual sediment yield during the 24 years of the study period was 562 T km -2 in the Mellah Catchment. This drainage basin had high rainfall and runoff, the erosion was high. The high sediment yield in the Mellah basin could be explained by a high percentage of sparse grassland and cultivation developed on shallow marly silty-clayey soils with steep slopes often exceeding 12%. Almost all suspended sediment loads are transported during storm events that mainly occur in the winter and spring heavy and medium downpours. The scarceness of these events leads to a very large interseasonal variability of the wadi sediment fluxes. The negative impacts of this enhanced sediment mobility are directly felt in the western part of the basin which shows many mass movements, bank and gully erosion because cultivated areas are often bared during autumnal brief flash floods and furrowed downslope during the winter season. (author)

Advanced Power Ultra-Uprates of Existing Plants (APPU) Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Rubiolo, Pablo R. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Conway, Lawarence E. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Oriani, Luca [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Lahoda, Edward J. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; DeSilva, Greg [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Hu, Min H. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Hartz, Josh [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Bachrach, Uriel [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Smith, Larry [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Dudek, Daniel F. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Toman, Gary J. [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Feng, Dandong [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hejzlar, Pavel [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Kazimi, Mujid S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2006-03-31

This project assessed the feasibility of a Power Ultra-Uprate on an existing nuclear plant. The study determined the technical and design limitations of the current components, both inside and outside the containment. Based on the identified plant bottlenecks, the design changes for major pieces of equipment required to meet the Power Ultra-Uprate throughput were determined. Costs for modified pieces of equipment and for change-out and disposal of the replaced equipment were evaluated. These costs were then used to develop capital, fuel and operating and maintenance cost estimates for the Power Ultra-Uprate plant. The cost evaluation indicates that the largest cost components are the replacement of power (during the outage required for the uprate) and the new fuel loading. Based on these results, the study concluded that, for a standard 4-loop plant, the proposed Power Ultra-Uprate is technically feasible. However, the power uprate is likely to be more expensive than the cost (per Kw electric installed) of a new plant when large capacity uprates are considered (>25%). Nevertheless, the concept of the Power Ultra-Uprate may be an attractive option for specific nuclear power plants where a large margin exists in the steam and power conversion system or where medium power increases (~600 MWe) are needed. The results of the study suggest that development efforts on fuel technologies for current nuclear power plants should be oriented towards improving the fuel performance (fretting-wear, corrosion, uranium load, manufacturing, safety) required to achieve higher burnup rather focusing on potential increases in the fuel thermal output.

Advanced Power Ultra-Uprates of Existing Plants (APPU) Final Scientific/Technical Report

International Nuclear Information System (INIS)

Rubiolo, Pablo R.; Conway, Lawarence E.; Oriani, Luca; Lahoda, Edward J.; DeSilva, Greg; Hu, Min H.; Hartz, Josh; Bachrach, Uriel; Smith, Larry; Dudek, Daniel F.; Toman, Gary J.; Feng, Dandong; Hejzlar, Pavel; Kazimi, Mujid S.

2006-01-01

This project assessed the feasibility of a Power Ultra-Uprate on an existing nuclear plant. The study determined the technical and design limitations of the current components, both inside and outside the containment. Based on the identified plant bottlenecks, the design changes for major pieces of equipment required to meet the Power Ultra-Uprate throughput were determined. Costs for modified pieces of equipment and for change-out and disposal of the replaced equipment were evaluated. These costs were then used to develop capital, fuel and operating and maintenance cost estimates for the Power Ultra-Uprate plant. The cost evaluation indicates that the largest cost components are the replacement of power (during the outage required for the uprate) and the new fuel loading. Based on these results, the study concluded that, for a ''standard'' 4-loop plant, the proposed Power Ultra-Uprate is technically feasible. However, the power uprate is likely to be more expensive than the cost (per Kw electric installed) of a new plant when large capacity uprates are considered (>25%). Nevertheless, the concept of the Power Ultra-Uprate may be an attractive option for specific nuclear power plants where a large margin exists in the steam and power conversion system or where medium power increases (∼600 MWe) are needed. The results of the study suggest that development efforts on fuel technologies for current nuclear power plants should be oriented towards improving the fuel performance (fretting-wear, corrosion, uranium load, manufacturing, safety) required to achieve higher burnup rather focusing on potential increases in the fuel thermal output

Rapid Sediment Accumulation Results in High Methane Effluxes from Coastal Sediments.

Directory of Open Access Journals (Sweden)

Matthias Egger

Full Text Available Globally, the methane (CH4 efflux from the ocean to the atmosphere is small, despite high rates of CH4 production in continental shelf and slope environments. This low efflux results from the biological removal of CH4 through anaerobic oxidation with sulfate in marine sediments. In some settings, however, pore water CH4 is found throughout the sulfate-bearing zone, indicating an apparently inefficient oxidation barrier for CH4. Here we demonstrate that rapid sediment accumulation can explain this limited capacity for CH4 removal in coastal sediments. In a saline coastal reservoir (Lake Grevelingen, The Netherlands, we observed high diffusive CH4 effluxes from the sediment into the overlying water column (0.2-0.8 mol m-2 yr-1 during multiple years. Linear pore water CH4 profiles and the absence of an isotopic enrichment commonly associated with CH4 oxidation in a zone with high rates of sulfate reduction (50-170 nmol cm-3 d-1 both suggest that CH4 is bypassing the zone of sulfate reduction. We propose that the rapid sediment accumulation at this site (~ 13 cm yr-1 reduces the residence time of the CH4 oxidizing microorganisms in the sulfate/methane transition zone (< 5 years, thus making it difficult for these slow growing methanotrophic communities to build-up sufficient biomass to efficiently remove pore water CH4. In addition, our results indicate that the high input of organic matter (~ 91 mol C m-2 yr-1 allows for the co-occurrence of different dissimilatory respiration processes, such as (acetotrophic methanogenesis and sulfate reduction in the surface sediments by providing abundant substrate. We conclude that anthropogenic eutrophication and rapid sediment accumulation likely increase the release of CH4 from coastal sediments.

Wyoming coal-conversion project. Final technical report, November 1980-February 1982. [Proposed WyCoalGas project, Converse County, Wyoming; contains list of appendices with title and identification

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

This final technical report describes what WyCoalGas, Inc. and its subcontractors accomplished in resolving issues related to the resource, technology, economic, environmental, socioeconomic, and governmental requirements affecting a project located near Douglas, Wyoming for producing 150 Billion Btu per day by gasifying sub-bituminous coal. The report summarizes the results of the work on each task and includes the deliverables that WyCoalGas, Inc. and the subcontractors prepared. The co-venturers withdrew from the project for two reasons: federal financial assistance to the project was seen to be highly uncertain; and funds were being expended at an unacceptably high rate.

Review of technical issues related to the failure of Rosemount pressure transmitters due to fill oil loss. Final report

International Nuclear Information System (INIS)

James, R.W.; Gaertner, J.P.; Burns, E.T.; Horn, A.; Lee, L.K.

1994-08-01

Rosemount pressure transmitters are extensively used in both safety and non-safety applications in US nuclear power plants. They are used to measure pressure, flow, and water level. Rosemount pressure transmitter models 1151, 1152, 1153A, 1153, and 1154 use a fill oil to hydraulically transmit process pressure exerted on outer isolating diaphragms to internal diaphragms. The resulting deflection of the internal diaphragms changes the distance between them and a central diaphragm separating the transmitter interior into two volumes. The change in distance is measured as a change in electrical capacitance between the isolating diaphragms and the central diaphragm and can be related to differential pressure. The fill oil also functions as a dielectric. It has been well established that this fill oil can potentially leak over time, decreasing transmitter accuracy and increasing transmitter response time. Ultimately, the transmitter can fail. An extensive effort has been expended by the nuclear power industry collectively to analyze this issue and develop technically sound and reasonable requirements to mitigate the effects of oil loss in Rosemount pressure transmitters. Despite this, technical concerns have still been raised regarding the technical validity of the past analyses of this problem and its scope. In May 1993, the NRC created an internal group to comprehensively review the Rosemount issue and the NRC's action in addressing it to ensure that all available technical information has been considered. Because this issue remains of active technical interest and because the past work on this subject has been done by many different groups and organizations, EPRI has prepared this report to thoroughly document the current technical understanding of this issue, to perform additional analysis, and to identify any appropriate additional technical research activities regarding oil loss in Rosemount pressure transmitters

Final Technical Report: Results of Phase 1

Energy Technology Data Exchange (ETDEWEB)

Narang, David, J.; Hambrick, Joshua; Srinivasan, Devarajan; Ayyannar, Raja; O' Brien, Kathleen

2011-09-28

working, utility distribution feeder. To address the technical challenges related to the integration of distributed PV when PV penetration levels reach or exceed 30% of the total load, technologies and methods to ensure the stable and safe operation of the feeder will be evaluated. Lessons learned will enable APS to improve the framework for future PV integration on its system and may also aid other utilities across the United States energy sector in accelerating the adoption of distributed photovoltaic generation.

Incorporation of Fine-Grained Sediment Erodibility Measurements into Sediment Transport Modeling, Capitol Lake, Washington

Science.gov (United States)

Stevens, Andrew W.; Gelfenbaum, Guy; Elias, Edwin; Jones, Craig

2008-01-01

Capitol Lake was created in 1951 with the construction of a concrete dam and control gate that prevented salt-water intrusion into the newly formed lake and regulated flow of the Deschutes River into southern Puget Sound. Physical processes associated with the former tidally dominated estuary were altered, and the dam structure itself likely caused an increase in retention of sediment flowing into the lake from the Deschutes River. Several efforts to manage sediment accumulation in the lake, including dredging and the construction of sediment traps upriver, failed to stop the lake from filling with sediment. The Deschutes Estuary Feasibility Study (DEFS) was carried out to evaluate the possibility of removing the dam and restoring estuarine processes as an alternative ongoing lake management. An important component of DEFS was the creation of a hydrodynamic and sediment transport model of the restored Deschutes Estuary. Results from model simulations indicated that estuarine processes would be restored under each of four restoration alternatives, and that over time, the restored estuary would have morphological features similar to the predam estuary. The model also predicted that after dam-removal, a large portion of the sediment eroded from the lake bottom would be deposited near the Port of Olympia and a marina located in lower Budd Inlet seaward of the present dam. The volume of sediment transported downstream was a critical piece of information that managers needed to estimate the total cost of the proposed restoration project. However, the ability of the model to predict the magnitude of sediment transport in general and, in particular, the volume of sediment deposition in the port and marina was limited by a lack of information on the erodibility of fine-grained sediments in Capitol Lake. Cores at several sites throughout Capitol Lake were collected between October 31 and November 1, 2007. The erodibility of sediments in the cores was later determined in the

Advising students in technical projects - recognizing problem scenarios

DEFF Research Database (Denmark)

Bærentzen, Jacob Andreas; Singh, Karan

2014-01-01

In this paper, we consider the advisor’s role during the technical work and the thesis preparation for a student in the final phase of a course of study in an engineering education. We initially claim that there is a marked difference between the learning that takes place in regular course work...

Estimating sediment discharge: Appendix D

Science.gov (United States)

Gray, John R.; Simões, Francisco J. M.

2008-01-01

Sediment-discharge measurements usually are available on a discrete or periodic basis. However, estimates of sediment transport often are needed for unmeasured periods, such as when daily or annual sediment-discharge values are sought, or when estimates of transport rates for unmeasured or hypothetical flows are required. Selected methods for estimating suspended-sediment, bed-load, bed- material-load, and total-load discharges have been presented in some detail elsewhere in this volume. The purposes of this contribution are to present some limitations and potential pitfalls associated with obtaining and using the requisite data and equations to estimate sediment discharges and to provide guidance for selecting appropriate estimating equations. Records of sediment discharge are derived from data collected with sufficient frequency to obtain reliable estimates for the computational interval and period. Most sediment- discharge records are computed at daily or annual intervals based on periodically collected data, although some partial records represent discrete or seasonal intervals such as those for flood periods. The method used to calculate sediment- discharge records is dependent on the types and frequency of available data. Records for suspended-sediment discharge computed by methods described by Porterfield (1972) are most prevalent, in part because measurement protocols and computational techniques are well established and because suspended sediment composes the bulk of sediment dis- charges for many rivers. Discharge records for bed load, total load, or in some cases bed-material load plus wash load are less common. Reliable estimation of sediment discharges presupposes that the data on which the estimates are based are comparable and reliable. Unfortunately, data describing a selected characteristic of sediment were not necessarily derived—collected, processed, analyzed, or interpreted—in a consistent manner. For example, bed-load data collected with

PVWatts Version 1 Technical Reference

Energy Technology Data Exchange (ETDEWEB)

Dobos, A. P.

2013-10-01

The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

Sedimentation rate and {sup 210}Pb sediment dating at Apipucos reservoir, Recife, Brazil

Energy Technology Data Exchange (ETDEWEB)

Figueiredo, Marcela D.C. de; Silva, Danubia B. da; Cunha, Manuela S. da; Rodrigues, Kelia R.G.; Pedroza, Eryka H.; Melo, Roberto T. de; Oliveira, Aristides; Hazin, Clovis A.; Souza, Vivianne L.B. de, E-mail: rtmelo@cnen.gov.b, E-mail: chazin@cnen.gov.b, E-mail: vlsouza@cnen.gov.b [Centro Regional de Ciencias Nucleares (CRCN-NE/CNEN-PE), Recife, PE (Brazil)

2011-07-01

The Apipucos Reservoir is located in Recife, State of Pernambuco, and, several districts of the metropolitan area use this reservoir to dispose waste and sewage. Dating sediments uses {sup 210}Pb from the atmosphere which is formed as a result of {sup 222}Rn emanation from the soil. Atmospheric lead, carried by rain, is called non-supported {sup 21}'0Pb, to differentiate it from the one contained in the sediment, in balance with the {sup 226}Ra. The model chosen for dating sediments depends on certain conditions: in an environment where the amount of sediment influx can vary, the constant rate of supply model is adopted. On the other hand, in environments where the sedimentation rate is constant and the sediment can be considered to have a constant initial concentration of unsupported {sup 210}Pb and the (CIC) model is applied. A 70-cm long, 5-cm internal-diameter wide core was collected for sediment dating. Each core was sliced, into 5 or 10 cm intervals. Samples were dried at 105 deg C, and about 5 g dry material from each sample was dissolved with acids. The {sup 210}Pb and {sup 226}Ra contents were separated and determined by beta and alpha counting by using a gas-flow proportional counter. Sediment ages were calculated by the two models, and for the second and fourth sampling points, both models could be used. The results showed an increase in sedimentation rate over the last 50 - 60 years. We can conclude that the top sediment layer is dated from 30 years ago. We can also conclude that the CRS is the best applicable model to use in this area. (author)

Numerical sedimentation particle-size analysis using the Discrete Element Method

Science.gov (United States)

Bravo, R.; Pérez-Aparicio, J. L.; Gómez-Hernández, J. J.

2015-12-01

Sedimentation tests are widely used to determine the particle size distribution of a granular sample. In this work, the Discrete Element Method interacts with the simulation of flow using the well known one-way-coupling method, a computationally affordable approach for the time-consuming numerical simulation of the hydrometer, buoyancy and pipette sedimentation tests. These tests are used in the laboratory to determine the particle-size distribution of fine-grained aggregates. Five samples with different particle-size distributions are modeled by about six million rigid spheres projected on two-dimensions, with diameters ranging from 2.5 ×10-6 m to 70 ×10-6 m, forming a water suspension in a sedimentation cylinder. DEM simulates the particle's movement considering laminar flow interactions of buoyant, drag and lubrication forces. The simulation provides the temporal/spatial distributions of densities and concentrations of the suspension. The numerical simulations cannot replace the laboratory tests since they need the final granulometry as initial data, but, as the results show, these simulations can identify the strong and weak points of each method and eventually recommend useful variations and draw conclusions on their validity, aspects very difficult to achieve in the laboratory.

Characterization and evaluation of potential reuse options for wastewater sludge and combined sewer system sediments in Mexico

Energy Technology Data Exchange (ETDEWEB)

Jimenez, B.; Mendez, J.M.; Barrios, J.A.; Salgado, G.; Sheinbaum, C.

2003-07-01

Combined sewer systems generate sediments that have characteristics similar to those of primary sludge. Mexico City has such a system composed of a network of pipes, regulation structures (dams, basins) and open channels. The annual generation of sediments is estimated in 2.8 Mm{sup 3}, which includes 0.41 Mm{sup 3} of sludge. As a result, the total capacity for transporting water is reduced considerably, making necessary to extract yearly an approximate 0.85 Mm{sup 3} of those materials and to send them to a final disposal site with a capacity that is being exhausted. As part of the local Governmental effort, this project evaluates the quality of sediments from 6 dams, 4 regulation basins, 2 open channels, and 3 transfer stations. Also, sludge from 20 wastewater treatment plants was sampled. The results showed an important presence of lead and hydrocarbons in some sediments, and some sludge samples contained arsenic and nickel above the limits. Moreover, microbial levels exceeded the limits in all the sediments and sludge samples. Erosion was linked to the generation of an important amount of sediments based on lead concentration. A classification was established to determine the degree of contamination of the sediments as well as the required treatment to allow their potential reuse. (author)

Incision and Landsliding Lead to Coupled Increase in Sediment Flux and Grain Size Export

Science.gov (United States)

Roda-Boluda, D. C.; Brooke, S.; D'Arcy, M. K.; Whittaker, A. C.; Armitage, J. J.

2017-12-01

concomitantly and scale non-linearly. Finally, we explore the consequences that this coupled sediment flux and grain size increase may have on basin stratigraphy, and we show that it has a significant effect on amplifying gravel front progradation.

Technical indicators of financial performance in the dairy herd

DEFF Research Database (Denmark)

Kristensen, Erling Lundager; Østergaard, Søren; Krogh, Mogens Agerbo

2008-01-01

Monte Carlo simulation was used to predict the long-term financial performance related to the technical performance of dairy herds. The indicators addressed were derived from data collected routinely in the herd. They indicated technical performance that can be affected by the farmer...... or the consultant, and they were derived from expected cause-effect relations between technical performance and financial performance at the herd level. The study included the indicators shape of lactation curve, reproduction efficiency, heifer management, variation between cows in lactation curve persistency...... cow was analyzed as the measure of financial performance. The potential effects of the selected indicators on the gross margin were estimated by means of an ANOVA. The final model allowed estimation of the financial value of specific changes within the key performance indicators. This study indicated...

HFBR: Review of the technical specifications against the FSAR

International Nuclear Information System (INIS)

Rao, D.V.; Boss, S.B.; Claiborne, E.R.; Darby, J.L.; Clark, R.A.

1990-01-01

The purpose of this review is to determine the adequacy of the High Flux Beam Reactor (HFBR) Technical Specifications for 40 MW operation by comparison with the HFBR Final Safety Analysis Report, particularly the accident analyses chapter. Specifically, the Technical Specifications were compared against the Design Basis Accident (DBA) Analyses presented in the Addendum to the HFBR FSAR for 60 MW Operation. The 60 MW DBA analyses was used since it is more current and complete than the analyses presented in the original FSAR which is considered obsolete. A listing of the required systems and equipment was made for each of the accidents analyzed. Additionally, the Technical Specification instrument setpoints were compared to the DBA analyses parametric values. Also included in this review was a comparison of the Technical Specification Bases against the FSAR and the identification of any differences. The HFBR Operations Procedures Manual (OPM) was also reviewed for any inconsistencies between the FSAR or the Technical Specifications. Upon completion of this review it was determined that the Technical Specifications are well written and the items commented on should not delay the low power restart (40 MW). Additionally, the OPM is also well written and does not require further modification before restart

Radiotracer and sealed source techniques for sediment management. Report of the consultants meeting

International Nuclear Information System (INIS)

2008-01-01

Radioisotopes as tracers and sealed sources have been a useful and often irreplaceable tool for sediment transport studies. Gamma scattering and transmission gauges are used for sediment monitoring. Computational fluid dynamics (CFD) modelling is now an essential tool for the management of the natural systems and are increasingly used to study the fate and behaviour of particulates and contaminants. Radiotracer techniques are often employed to validate CFD models to enhance confidence in the predictive value of the models. Experimental tracing and numerical modelling are complementary methods of studying complex systems. During the last few decades, many radiotracer studies for the investigation of sediment transport in natural systems have been conducted worldwide, and various techniques for tracing and monitoring sediment have been developed by individual tracer groups. However, the developed techniques and methods for sediment tracing have not been compiled yet as a technical document, which is essential for the preservation of the knowledge and transfer of the technology to developing countries. Standard procedures or guidelines for the tracer experiments, which are vital for the reliability of the experiments and the acceptance of end-users, have not been established by the international tracer community either. The use of radiotracers in sediment transport studies demands the additional attention of the community to further develop these techniques and to ensure their transfer to developing countries. The Consultants' Meeting on 'Radiotracer and sealed source techniques for sediment management' was convened at the headquarters of the International Atomic Energy Agency (IAEA) in Vienna, Austria, from 21 to 25 April 2008. Experts from Argentina, Brazil, France, India, Republic of Korea and United Kingdom have been invited to discuss the current status of the tracer and nucleonic gauge technologies as applied for sediment transport investigations and to evaluate

Radiotracer and sealed source techniques for sediment management. Report of the consultants meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

Radioisotopes as tracers and sealed sources have been a useful and often irreplaceable tool for sediment transport studies. Gamma scattering and transmission gauges are used for sediment monitoring. Computational fluid dynamics (CFD) modelling is now an essential tool for the management of the natural systems and are increasingly used to study the fate and behaviour of particulates and contaminants. Radiotracer techniques are often employed to validate CFD models to enhance confidence in the predictive value of the models. Experimental tracing and numerical modelling are complementary methods of studying complex systems. During the last few decades, many radiotracer studies for the investigation of sediment transport in natural systems have been conducted worldwide, and various techniques for tracing and monitoring sediment have been developed by individual tracer groups. However, the developed techniques and methods for sediment tracing have not been compiled yet as a technical document, which is essential for the preservation of the knowledge and transfer of the technology to developing countries. Standard procedures or guidelines for the tracer experiments, which are vital for the reliability of the experiments and the acceptance of end-users, have not been established by the international tracer community either. The use of radiotracers in sediment transport studies demands the additional attention of the community to further develop these techniques and to ensure their transfer to developing countries. The Consultants' Meeting on 'Radiotracer and sealed source techniques for sediment management' was convened at the headquarters of the International Atomic Energy Agency (IAEA) in Vienna, Austria, from 21 to 25 April 2008. Experts from Argentina, Brazil, France, India, Republic of Korea and United Kingdom have been invited to discuss the current status of the tracer and nucleonic gauge technologies as applied for sediment transport investigations and to evaluate

Sediment and radionuclide transport in rivers: radionuclide transport modeling for Cattaraugus and Buttermilk Creeks, New York

International Nuclear Information System (INIS)

Onishi, Y.; Yabusaki, S.B.; Kincaid, C.T.; Skaggs, R.L.; Walters, W.H.

1982-12-01

SERATRA, a transient, two-dimensional (laterally-averaged) computer model of sediment-contaminant transport in rivers, satisfactorily resolved the distribution of sediment and radionuclide concentrations in the Cattaraugus Creek stream system in New York. By modeling the physical processes of advection, diffusion, erosion, deposition, and bed armoring, SERATRA routed three sediment size fractions, including cohesive soils, to simulate three dynamic flow events. In conjunction with the sediment transport, SERATRA computed radionuclide levels in dissolved, suspended sediment, and bed sediment forms for four radionuclides ( 137 Cs, 90 Sr, 239 240 Pu, and 3 H). By accounting for time-dependent sediment-radionuclide interaction in the water column and bed, SERATA is a physically explicit model of radionuclide fate and migration. Sediment and radionuclide concentrations calculated by SERATA in the Cattaraugus Creek stream system are in reasonable agreement with measured values. SERATRA is in the field performance phase of an extensive testing program designed to establish the utility of the model as a site assessment tool. The model handles not only radionuclides but other contaminants such as pesticides, heavy metals and other toxic chemicals. Now that the model has been applied to four field sites, including the latest study of the Cattaraugus Creek stream system, it is recommended that a final model be validated through comparison of predicted results with field data from a carefully controlled tracer test at a field site. It is also recommended that a detailed laboratory flume be tested to study cohesive sediment transport, deposition, and erosion characteristics. The lack of current understanding of these characteristics is one of the weakest areas hindering the accurate assessment of the migration of radionuclides sorbed by fine sediments of silt and clay

An Assessment of health risk associated with mercury in soil and sediment from East Fork Poplar Creek, Oak Ridge, Tennessee. Final report

Energy Technology Data Exchange (ETDEWEB)

Revis, N.; Holdsworth, G.; Bingham, G.; King, A.; Elmore, J.

1989-04-01

This report presents results from a study conducted to determine the toxicity of Mercury in soils sediments samples. Mice were fed via diet, soils and sediment, from various locations along the East Fork Poplar creek. Tissue distribution of pollutants was determined at various intervals. The tissue level relative to toxicity was used to determine the effect of a complex matrix on the gastrointestinal absorption and tissue distribution of the pollutants (other pollutants included cadmium and selenium).

Algal stabilisation of estuarine sediments

International Nuclear Information System (INIS)

1992-01-01

The presence of benthic microalgae can increase the stability of intertidal sediments and influence sediment fluxes within an estuarine environment. Therefore the relative importance of algal stabilisation needs to be understood to help predict the effects of a tidal barrage. The biogenic stabilisation of intertidal estuarine sediments by epipelic diatom films and the macrophyte Vaucheria was studied at three sites on the Severn Estuary. The cohesive strength meter (CSM) was developed to measure surface critical shear stress with varied algal density. A number of techniques have been used to determine the general in situ erodibility of cohesive estuarine sediments. The measurements of sediment shear strength and critical erosion velocity were investigated. Field experiments were undertaken to investigate the effect of algae on binding sediments, and a predictive method for the assessment of sediment stabilisation by algal binding was developed. (author)

Release of aged contaminants from weathered sediments: Effects of sorbate speciation on scaling of reactive transport

Energy Technology Data Exchange (ETDEWEB)

Chorover, Jon; Perdrial, Nico; Mueller, Karl; Strepka, Caleb; O’Day, Peggy; Rivera, Nelson; Um, Wooyong; Chang, Hyun-Shik; Steefel, Carl; Thompson, Aaron

2012-11-05

Hanford sediments impacted by hyperalkaline high level radioactive waste have undergone incongruent silicate mineral weathering concurrent with contaminant uptake. In this project, we studied the impact of background pore water (BPW) on strontium, cesium and iodine desorption and transport in Hanford sediments that were experimentally weathered by contact with simulated hyperalkaline tank waste leachate (STWL) solutions. Using those lab-weathered Hanford sediments (HS) and model precipitates formed during nucleation from homogeneous STWL solutions (HN), we (i) provided thorough characterization of reaction products over a matrix of field-relevant gradients in contaminant concentration, partial pressure of carbon dioxide, and reaction time; (ii) improved molecular-scale understanding of how sorbate speciation controls contaminant desorption from weathered sediments upon removal of caustic sources; and (iii) developed a mechanistic, predictive model of meso- to field-scale contaminant reactive transport under these conditions. In this final report, we provide detailed descriptions of our results from this three-year study, completed in 2012 following a one-year no cost extension.

Influence of Calcite and Dissolved Calcium on Uranium(VI) Sorption to a Hanford Subsurface Sediment

International Nuclear Information System (INIS)

Dong, Wenming; Ball, William P.; Liu, Chongxuan; Wang, Zheming; Stone, Alan T.; Bai, Jing; Zachara, John M.

2005-01-01

The influence of calcite and dissolved calcium on U(VI) adsorption was investigated using a calcite-containing sandy silt/clay sediment from the U. S. Department of Energy Hanford site. U(VI) adsorption to sediment, treated sediment, and sediment size fractions was studied in solutions that both had and had not been preequilibrated with calcite, at initial [U(VI)] ) 10-7-10-5 mol/L and final pH ) 6.0- 10.0. Kinetic and reversibility studies (pH 8.4) showed rapid sorption (30 min), with reasonable reversibility in the 3-day reaction time. Sorption from solutions equilibrated with calcite showed maximum U(VI) adsorption at pH 8.4 (0.1. In contrast, calcium-free systems showed the greatest adsorption at pH 6.0-7.2. At pH > 8.4, U(VI) adsorption was identical from calcium-free and calcium-containing solutions. For calcite-presaturated systems, both speciation calculations and laser-induced fluorescence spectroscopic analyses indicated that aqueous U(VI) was increasingly dominated by Ca2UO2(CO3)3 0(aq) at pH<8.4 and that formation of Ca2UO2(CO3)3 0(aq) is what suppresses U(VI) adsorption. Above pH 8.4, aqueous U(VI) speciation was dominated by UO2(CO3)3 4- in all solutions. Finally, results also showed that U(VI) adsorption was additive in regard to size fraction but not in regard to mineral mass: Carbonate minerals may have blocked U(VI) access to surfaces of higher sorption affinity

Uranium hydrogeochemical and stream sediment reconnaissance of the Kenai NTMS quadrangle, Alaska

International Nuclear Information System (INIS)

1981-08-01

This report presents results of a Hydrogeochemical and Stream Sediment Reconnaissance of the Kenai NTMS quadrangle, Alaska. In addition to this abbreviated data release, more complete data are available to the public in machine-readable form. These machine-readable data, as well as quarterly or semiannual program progress reports containing further information on the HSSR program in general, or on the Los Alamos National Laboratory portion of the program in particular, are available from DOE's Technical Library at its Grand Junction Area Office. Presented in this data release are location data, field analyses, and laboratory analyses of several different sample media. For the sake of brevity, many field site observations have not been included in this volume; these data are, however, available on the magnetic tape. Appendices A through D describe the sample media and summarize the analytical results for each medium. The data have been subdivided by one of the Los Alamos National Laboratory sorting programs of Zinkl and others (1981a) into groups of stream-sediment, lake-sediment, stream-water, lake-water, and ground-water samples. For each group which contains a sufficient number of observations, statistical tables, tables of raw data, and 1:1,000,000 scale maps of pertinent elements have been included in this report. Also included are maps showing results of multivariate statistical analyses

Uranium hydrogeochemical and stream sediment reconnaissance of the Denver NTMS quadrangle, Colorado

International Nuclear Information System (INIS)

1981-11-01

This report presents results of a Hydrogeochemical and Stream Sediment Reconnaissance of the Denver NTMS quadrangle, Colorado. In addition to this abbreviated data release, more complete data are available to the public in machine-readable form. These machine-readable data, as well as quarterly or semiannual program progress reports containing further information on the HSSR program in general, or on the Los Alamos National Laboratory portion of the program in particular, are available from DOE's Technical Library at its Grand Junction Area Office. Presented in this data release are location data, field analyses, and laboratory analyses of several different sample media. For the sake of brevity, many field site observations have not been included in this volume; these data are, however, available on the magnetic tape. Appendices A through E describe the sample media and summarize the analytical results for each medium. The data have been subdivided by one of the Los Alamos National Laboratory sorting programs of Zinkl and others (1981a) into groups of stream-sediment, lake-sediment, stream-water, lake-water, and ground-water samples. For each group which contains a sufficient number of observations, statistical tables, tables of raw data, and 1:1,000,000 scale maps of pertinent elements have been included in this report. Also included are maps showing results of multivariate statistical analyses

Geopressured energy availability. Final report

Energy Technology Data Exchange (ETDEWEB)

1980-07-01

Near- and long-term prospects that geopressured/geothermal energy sources could become a viable alternative fuel for electric power generation were investigated. Technical questions of producibility and power generation were included, as well as economic and environmental considerations. The investigators relied heavily on the existing body of information, particularly in geotechnical areas. Statistical methods were used where possible to establish probable production values. Potentially productive geopressured sediments have been identified in twenty specific on-shore fairways in Louisiana and Texas. A total of 232 trillion cubic feet (TCF) of dissolved methane and 367 x 10/sup 15/ Btu (367 quads) of thermal energy may be contained in the water within the sandstone in these formations. Reasonable predictions of the significant reservoir parameters indicate that a maximum of 7.6 TCF methane and 12.6 quads of thermal energy may be producible from these potential reservoirs.

Hourly and daily variation of sediment redox potential in tidal wetland sediments

Science.gov (United States)

Catallo, W. James

1999-01-01

Variation of electrochemical oxidation-reduction (redox) potential was examined in surface salt march sediments under conditions of flooding and tidal simulation in mesocosms and field sites. Time series were generated of redox potential measured in sediment profiles at 2-10 cm depth using combination Pt-Ag/AgCl (ORP) electrodes. Redox potential data were acquired at rapid rates (1-55 samples/h) over extended periods (3-104 days) along with similar times series of temperature (water, air, soil) and pH. It was found that redox potential vaired as a result of water level changes and was unrelated to diurnal changes in temperature or pH, the latter of which changed by 370 mV redox potential decrease in under 48 hours). Attenuatoin of microbial activity by [gamma] y-radiation and toxic chemicals elimintated this response. In tidal salt marsh mesocosms where the sediment-plant assemblages were exposed to a simulated diurnal tide, redox potenial oscillations of 40-300 mV amplitude were recoded that has the same periodicity as the flood-drain cycle. Periodic redoc potential time series were observed repeatedly in sediments receiving tidal pulsing but not in those sediments exposed to static hydrological conditions. Data collected over 12 days from a coastal marsh site experiencing diurnal tides showed similar fluctuations in redox potential. Data from the experimentents indicated that (a) redox potential can be a dynamic, nonlinear variable in coastal and estuarine wetland sediments over hourly and daily scales, and the designs of biogeochemical experiments should reflect this, (b) redox potential can change rapidly and signigicantly in coastal wetland sediments in response of flooding and draining, (c) microbial community processes are primarily determinants of the time course of redox potential in wetland sediments, and elimination of inhibition of microbial activity (e.g. by pollutants) can significantly alter that behavior, and (d) fast redox potential dynamics appear

The dirt on sediments

Science.gov (United States)

Smith, Loren M.; Euliss, Ned H. "Chip"

2010-01-01

In the wetland science field, sediment deposition is often thought of as being beneficial especially when one thinks of coastal estuarine systems. For example, sediments deposited from streams and rivers are necessary to naturally build and maintain tidal marshes. These sediments come from eroded upland soils in the interior of the continent. When these sediments are diverted from natural coastal deposition areas, such as occurs from river channelization, we lose marshes through subsidence as is happening throughout coastal Louisiana. However, the value of eroded soils is all a matter of hydrogeomorphic perspective.

Geochemistry of sediments

Digital Repository Service at National Institute of Oceanography (India)

Nath, B.N.

Considering the potential of elemental data in marine sediments as diagnostic tools of various geological and oceanographic processes, sediment geochemical data from the Indian Ocean region has been reviewed in this article. Emphasis is laid...

Asymmetric fluxes of water and sediments in a mesotidal mudflat channel

Science.gov (United States)

Mariotti, G.; Fagherazzi, S.

2011-01-01

The hydrodynamics of a small tributary channel and its adjacent mudflat is studied in Willapa Bay, Washington State, USA. Velocity profiles and water levels are simultaneously measured at different locations in the channel and on the mudflat for two weeks. The above tidal flat and channel hydrodynamics differ remarkably during the tidal cycle. When the water surface level is above the tidal flat elevation, the channel is inactive. At this stage, the above tidal flat flow is predominantly aligned along the Bay axis, oscillating with the tide as a standing wave with peak velocities up to 0.3 m/s. When the mudflat becomes emergent, the flow concentrates in the channel. During this stage, current velocities up to 1 m/s are measured during ebb; and up to 0.6 m/s during flood. Standard equations for open-channel flow are utilized to study the channel hydrodynamics. From the continuity equation, a lateral inflow is predicted during ebb, which likely originates from the drainage of the mudflat through the lateral runnels. Both advective acceleration and lateral discharge terms, estimated directly from the velocity profiles, play a significant role in the momentum equation. The computed drag coefficient for bottom friction is small, due to an absence of vegetation and bottom bedforms in the channel. Sediment fluxes are calculated by combining flow and suspended sediment concentration estimated using the acoustic backscatter signal of the instruments. A net export of the sediment from the channel is found during ebb, which is not balanced by the sediment import during flood. When the mudflat is submerged, ebb-flood asymmetries in suspended sediment concentration are present, leading to a net sediment flux toward the inner part of the Willapa Bay. Finally, a residual flow is detected inside the channel at high slack water, probably associated with the thermohaline circulation.

Indicators: Sediment Enzymes

Science.gov (United States)

Sediment enzymes are proteins that are produced by microorganisms living in the sediment or soil. They are indicators of key ecosystem processes and can help determine which nutrients are affecting the biological community of a waterbody.

A multicriteria-based methodology for site prioritisation in sediment management.

Science.gov (United States)

Alvarez-Guerra, Manuel; Viguri, Javier R; Voulvoulis, Nikolaos

2009-08-01

Decision-making for sediment management is a complex task that incorporates the selections of areas for remediation and the assessment of options for any mitigation required. The application of Multicriteria Analysis (MCA) to rank different areas, according to their need for sediment management, provides a great opportunity for prioritisation, a first step in an integrated methodology that finally aims to assess and select suitable alternatives for managing the identified priority sites. This paper develops a methodology that starts with the delimitation of management units within areas of study, followed by the application of MCA methods that allows ranking of these management units, according to their need for remediation. This proposed process considers not only scientific evidence on sediment quality, but also other relevant aspects such as social and economic criteria associated with such decisions. This methodology is illustrated with its application to the case study area of the Bay of Santander, in northern Spain, highlighting some of the implications of utilising different MCA methods in the process. It also uses site-specific data to assess the subjectivity in the decision-making process, mainly reflected through the assignment of the criteria weights and uncertainties in the criteria scores. Analysis of the sensitivity of the results to these factors is used as a way to assess the stability and robustness of the ranking as a first step of the sediment management decision-making process.

The SocioEconomic Analysis of Repository Siting (SEARS): Technical description: Final draft

International Nuclear Information System (INIS)

1984-11-01

Socioeconomic impacts must be assessed both for the near term and for the future. One means of addressing the need for the assessment of such impacts has been through the development of the computerized socioeconomic assessment model called the SocioEconomic Analysis of Repository Siting (SEARS) model. The SEARS model was developed for the Battelle Project Management Division. It was refined and adapted from state-of-the-art computerized projection models and thoroughly validated and is now available for use in projecting the likely socioeconomic impacts of a repository facility. This Technical Description is one of six major products that describe the SEARS modeling system. 61 refs., 11 figs., 9 tabs

Final Technical Report of the project "Controlling Quantum Information by Quantum Correlations"

Energy Technology Data Exchange (ETDEWEB)

Girolami, Davide [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-17

The report describes hypotheses, aims, methods and results of the project 20170675PRD2, “Controlling Quantum Information by Quantum Correlations”, which has been run from July 31, 2017 to January 7, 2018. The technical work has been performed by Director’s Fellow Davide Girolami of the T-4 Division, Physics of Condensed Matter and Complex Systems, under the supervision of Wojciech Zurek (T-4), Lukasz Cincio (T-4), and Marcus Daniels (CCS-7). The project ended as Davide Girolami has been converted to J. R. Oppenheimer Fellow to work on the project 20180702PRD1, “Optimal Control of Quantum Machines”, started on January 8, 2018.

Achieving Hydrogen Storage Goals through High-Strength Fiber Glass - Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Li, Hong [PPG Industries, Inc., Cheswick, PA (United States); Johnson, Kenneth I. [PPG Industries, Inc., Cheswick, PA (United States); Newhouse, Norman L. [PPG Industries, Inc., Cheswick, PA (United States)

2017-06-05

Led by PPG and partnered with Hexagon Lincoln and Pacific Northwest National Laboratory (PNNL), the team recently carried out a project “Achieving Hydrogen Storage Goals through High-Strength Fiber Glass”. The project was funded by DOE’s Fuel Cell Technologies office within the Office of Energy Efficiency and Renewable Energy, starting on September 1, 2014 as a two-year project to assess technical and commercial feasibilities of manufacturing low-cost, high-strength glass fibers to replace T700 carbon fibers with a goal of reducing the composite total cost by 50% of the existing, commercial 700 bar hydrogen storage tanks used in personal vehicles.

Effects of engineered nanomaterials on microbial catalyzed biogeochemical processes in sediments

Energy Technology Data Exchange (ETDEWEB)

Gao Jie, E-mail: jgao@perc.ufl.edu [Department of Environmental Engineering Sciences, University of Florida, Gainesville, FL 32611 (United States); Wang Yu; Hovsepyan, Anna [Department of Environmental Engineering Sciences, University of Florida, Gainesville, FL 32611 (United States); Bonzongo, Jean-Claude J., E-mail: bonzongo@ufl.edu [Department of Environmental Engineering Sciences, University of Florida, Gainesville, FL 32611 (United States)

2011-02-15

Engineered nanomaterials (ENMs) are anticipated to find use in many human activities and commercial products. Concerns are therefore being raised regarding their environmental fate and toxicological implications, which remain largely unknown. In this study, we investigate the effects of C{sub 60}, nano-Ag and CdSe quantum dots (QD) on microbial-catalyzed oxidation of organic matter in freshwater sediments. Sediment slurries spiked with sodium acetate at a final concentration of 150 mg/L were separately treated with pre-identified toxic levels of the tested ENMs. The study focused primarily on acetate oxidation by nitrate reducing bacteria. Sediment slurries were incubated under anaerobic conditions in parallel with control samples, and changes in concentrations of acetate, nitrate and nitrite tracked over time. The results showed that tested C{sub 60} concentration completely inhibited the microbial oxidation of acetate, whereas the addition of nano-Ag and CdSe QD to sediment slurries negatively affected the rates of acetate oxidation. Under conditions with nitrate as prevalent electron acceptor, reaction rates of acetate degradation decreased from 0.44 day{sup -1} in control slurries to 0.24 day{sup -1} and 0.20 day{sup -1} in slurries treated with nano-Ag and CdSe QD, respectively. These preliminary results call for further investigations on potential long-term effects of ENMs on microbial driven basic ecosystem services.

Technical procedures for land use, Deaf Smith County site, Texas: Environmental Field Program: Final draft

International Nuclear Information System (INIS)

1987-09-01

This volume contains Technical Procedures pursuant to the Land Use Site Study Plan including land use data acquisition, land use/land cover map compilation, verification of land use/land cover map accuracy, and land use/land cover data analysis. 22 refs., 5 figs

Conceptualizing the role of sediment in sustaining ecosystem services: Sediment-ecosystem regional assessment (SEcoRA).

Science.gov (United States)

Apitz, Sabine E

2012-01-15

There is a growing trend to include a consideration of ecosystem services, the benefits that people obtain from ecosystems, within decision frameworks. Not more than a decade ago, sediment management efforts were largely site-specific and held little attention except in terms of managing contaminant inputs and addressing sediments as a nuisance at commercial ports and harbors. Sediments figure extensively in the Millennium Ecosystem Assessment; however, contaminated sediment is not the dominant concern. Rather, the focus is on land and water use and management on the landscape scale, which can profoundly affect soil and sediment quality, quantity and fate. Habitat change and loss, due to changes in sediment inputs, whether reductions (resulting in the loss of beaches, storm protection, nutrient inputs, etc.) or increases (resulting in lake, reservoir and wetland infilling, coral reef smothering, etc.); eutrophication and reductions in nutrient inputs, and disturbance due to development and fishing practices are considered major drivers, with significant consequences for biodiversity and the provision and resilience of ecosystem functions and services. As a mobile connecting medium between various parts of the ecosystem via the hydrocycle, sediments both contaminated and uncontaminated, play both positive and negative roles in the viability and sustainability of social, economic, and ecological objectives. How these roles are interpreted depends upon whether sediment status (defined in terms of sediment quality, quantity, location and transport) is appropriate to the needs of a given endpoint; understanding and managing the dynamic interactions of sediment status on a diverse range of endpoints at the landscape or watershed scale should be the focus of sediment management. This paper seeks to provide a language and conceptual framework upon which sediment-ecosystem regional assessments (SEcoRAs) can be developed in support of that goal. Copyright © 2011 Elsevier B

Sediment studies at Bikini Atoll part 2. inventories of transuranium elements in surface sediments

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V.E.; Eagle, R.J.; Wong, K.M.; Robison, W.L.

1997-10-01

This is the second of three reports on Bikini sediment studies, which discusses the concentrations and inventories of {sup 241}Am and {sup 239+240}Pu in sediments from the lagoon. Surface sediment samples were collected from 87 locations over the entire lagoon at Bikini Atoll during 1979. The collections were made to map the distribution of long-lived radionuclides associated with the bottom material and to show what modifications occurred in the composition of the sediment as a result of the testing program. Present inventories for {sup 241}Am and {sup 239+240}Pu in the surface 2 cm of sediment are estimated to be 14 and 17 TBq, respectively. These values are estimated to represent only 14% of the total inventory in the sediment column. Sediment inventories of {sup 239+240}Pu and {sup 241}Am are changing only slowly with time through chemical- physical processes that continuously mobilize small amounts of the transuranics to the water column. The lowest concentrations and inventories are associated with deposits logoonward of the eastern reef.