WorldWideScience

Sample records for sediment deposition evaluation

  1. Evaluation of Deposited Sediment and Macroinvertebrate Metrics Used to Quantify Biological Response to Excessive Sedimentation in Agricultural Streams

    Science.gov (United States)

    Sutherland, Andrew B.; Culp, Joseph M.; Benoy, Glenn A.

    2012-07-01

    The objective of this study was to evaluate which macroinvertebrate and deposited sediment metrics are best for determining effects of excessive sedimentation on stream integrity. Fifteen instream sediment metrics, with the strongest relationship to land cover, were compared to riffle macroinvertebrate metrics in streams ranging across a gradient of land disturbance. Six deposited sediment metrics were strongly related to the relative abundance of Ephemeroptera, Plecoptera and Trichoptera and six were strongly related to the modified family biotic index (MFBI). Few functional feeding groups and habit groups were significantly related to deposited sediment, and this may be related to the focus on riffle, rather than reach-wide macroinvertebrates, as reach-wide sediment metrics were more closely related to human land use. Our results suggest that the coarse-level deposited sediment metric, visual estimate of fines, and the coarse-level biological index, MFBI, may be useful in biomonitoring efforts aimed at determining the impact of anthropogenic sedimentation on stream biotic integrity.

  2. Evaluation of suspended sediment concentrations, sediment fluxes and sediment depositions along a reservoir by using laser diffraction and acoustic backscatter data

    Science.gov (United States)

    Lizano, Laura; Haun, Stefan

    2015-04-01

    The construction of dams and reservoirs disturb the natural morphological behavior of rivers. A natural settling effect occurs due to the reduced turbulences and flow velocities. As a consequence, reservoirs fill up with sediments which results in a reduction of storage volume, influences the operation of hydropower plants and leads in several cases to flood protection problems. The sediment depositions in reservoirs are standardly evaluated by using bathymetric data, obtained by a single beam sonar from pre-defined cross sections or by an extensive evaluation of the reservoir bed by a side scan sonar. However, a disadvantage of this method is that it is not possible to evaluate the pore water content of the depositions, which may lead as consequence to an uncertainty in the measured amount of deposited sediments. Given that a major part of sediments entering reservoirs are transported in suspension, sediment flux measurements along defined transects could give more reliable information on the settled amount of sediments and additional information on the sediment transport mechanism within the reservoir. An evaluation of the sediment fluxes is in practice often conducted by a single suspended sediment concentration (SSC) measurement in combination with a cross sectional calibration factor to take changes in the SSC along the transect into account. However, these calibration factors are often developed only for one specific in-situ condition and may give unreliable results in case that the boundaries change e.g. the hydraulic conditions. Hence an evaluation of the sediment fluxes along the whole transect would give a more reliable number for the amount of transported sediments through the reservoir. This information can afterwards be used to calculate the amount of settled sediments in different sections of the reservoir and the amount of sediments which will enter the intake. For this study the suspended sediment transport within the Peñas Blancas reservoir in

  3. Earth Surface Processes, Landforms and Sediment Deposits

    Science.gov (United States)

    Bridge, John; Demicco, Robert

    Earth surface processes, landforms and sediment deposits are intimately related - involving erosion of rocks, generation of sediment, and transport and deposition of sediment through various Earth surface environments. These processes, and the landforms and deposits that they generate, have a fundamental bearing on engineering, environmental and public safety issues; on recovery of economic resources; and on our understanding of Earth history. This unique textbook brings together the traditional disciplines of sedimentology and geomorphology to explain Earth surface processes, landforms and sediment deposits in a comprehensive and integrated way. It is the ideal resource for a two-semester course in sedimentology, stratigraphy, geomorphology, and Earth surface processes from the intermediate undergraduate to beginning graduate level. The book is also accompanied by a website hosting illustrations and material on field and laboratory methods for measuring, describing and analyzing Earth surface processes, landforms and sediments.

  4. Sediment problems in reservoirs. Control of sediment deposits

    Energy Technology Data Exchange (ETDEWEB)

    Jacobsen, Tom

    1997-12-31

    When a reservoir is formed on a river, sediment will deposit in the reservoir. Such processes are unfortunate, for instance, for the implementation of hydroelectric energy. This thesis studies the problem of reservoir sedimentation and discusses methods of removing the sediments. Various aspects of reservoir sedimentation are discussed. Anthropogenic impacts seem to greatly affect the erosion processes. Temporal distribution is uneven, mainly because of the very large flood events. A world map showing the Reservoir Capacity: Annual Sediment Inflow ratio for reservoirs with volume equal to 10% of annual inflow has been prepared. The map shows that sedimentation is severe in the western parts of North and South America, eastern, southern and northern Africa, parts of Australia and most of Asia. The development of medium-sized reservoirs is difficult, as they are too large for conventional flushing technique and too small to store the sediment that accumulates during their economic lifetime. A computer model, SSIIM, was used with good results in a case study of two flood drawdown trials in Lake Roxburg, New Zealand. Two techniques have been developed that permits controlled suction of sediment and water into a pipe: the Slotted Pipe Sediment Sluicer (SPSS) and the Saxophone Sediment Sluicer (SSS). The techniques exploit the inflow pattern in through a slot in a pipe. An equation describing this inflow pattern was derived and verified experimentally. The SPSS is fixed near the reservoir bed, and sediment that deposits on top of it is removed in the sluicing process. The SSS sluices sediment from the surface of the sediment deposits. Some technical and economic conditions affecting the economics of sediment removal from reservoirs have been identified and studied. 79 refs., 112 figs., 14 tabs.

  5. Erosion and sediment deposition evaluation on a slope under pasture in Jandaia-GO using the '137Cs fallout' technique

    International Nuclear Information System (INIS)

    Arthur, Robson C.J.; Bacchi, Osny O.S.; Reichardt, Klaus; Oliveira, Carloeme Alves de; Correchel, Vladia

    2009-01-01

    Water erosion is one of the main forms of soil degradation and among the diverse factors that affect it, two of great importance are the soil cover and slope. Estimates of sediment distribution rates associated to the different uses and soil management practices are scarce and the employed methods in these determinations are in general costly and time consuming. Rates of sediment redistribution evaluated by means of the 137 Cs technique are based on the comparison of inventories of individual points of a given position and an inventory of reference, whose value represents the amount of 137 Cs of 'fallout' origin that was added to the local site. This allows evaluating situations of losses and accumulations of sediments by the erosive process. The objective of the present work was to analyze the sediment production in a pasture area and to measure the efficiency of riparian forests in trapping the erosion sediments coming from pasture, through the ' 137 Cs fallout' redistribution analysis. The study was carried out in Jandaia/GO, Brazil, in two dowslope transects located in a pasture area. Samples were taken from seven points of two 140 m long transects, as well as from three soil profiles of a 15 m transect in the downstream riparian forests of each transect. Soil profiles were sampled in three layers of 20 cm (0-20, 20-40 and 40-60). The soil samples were air dried, sieved and then analyzed for 137 Cs activity by a gamma ray detector (GEM-20180P, EG and ORTEC) coupled to a multichannel analyzer at CENA/USP. The results indicate variations of 137 Cs activity in soil profiles and high erosion rates to the riparian forest to the pasture areas of the two transects, showing sediment movement from the pasture area to the riparian forest, which suggests that the current width of the forest is not wide enough to trap the sediments produced upslope in the pasture area. (author)

  6. Evaluation of heavy metals transfer: impact of a dredged sediment deposit on a on-polluted soil; Migration des polluants metalliques: cas d'un depot de sediments contamines sur un sol non pollue

    Energy Technology Data Exchange (ETDEWEB)

    Vauleon, C.; Laboudigue, A. [Centre National de Recherche sur les Sites et Sols Pollues, CNRSSP, 59 - Douai (France); Tiffreau, Ch. [CEA Cadarache, 13 - Saint Paul lez Durance (France)

    2001-07-01

    In many countries and especially in the North of France, inland waterways need to be dredged regularly to provide a high quality environment for customers, staff and local communities. However, dredging operations generate yearly large quantities of sediments, which in spite of their high pollutant contents, are often stored in non-specific sites. Thus, the threat of a spreading contamination for the surrounding environment is important. In order to evaluate this potential risk and to quantify the transfer of heavy metals from the dredged layer to the non-polluted soil below, an interdisciplinary research project was undertaken including, (i) the monitoring of an experimental sediment deposit, (ii) the microscopic study of metal distribution inside this deposit, (iii) the evaluation of microbial activity, (iv) the impact of natural vegetation growth on metal migration. Up to now, the main processes identified (oxidation of sulphur compounds, vertical migration of Zinc) allowed us to make several recommendations for the future management of dredged sediments by: (i) controlling the oxidation processes during dredging operations or (ii) assessing the high neutralizing capacity of the local environment of deposition. Moreover, an adequate vegetation management can reduce the heavy metals migration to groundwater's with maximum efficiency and at low costs. (author)

  7. Anthropogenic mercury deposition to arctic lake sediments

    Energy Technology Data Exchange (ETDEWEB)

    Hermanson, M.H. [Westchester University, Westchester, PA (United States). Dept. of Health

    1998-01-01

    The history of atmospheric mercury inputs to remote arctic regions can be measured in lake sediment cores using lead-210 chronology. In the investigation, total mercury deposition is measured in sediments from Imitavik and Annak Lakes on the Belcher Islands in southeastern Hudson Bay, an area in the southern Canadian Arctic with no history of local industrial or agricultural sources of contamination. Both lakes received background and atmospheric inputs of mercury while Annak also received mercury from raw domestic sewage from the Hamlet of Sanikiluaq, a growing Inuit community of about 550 established in the late 1960s. Results from Imitavik show that anthropogenic mercury inputs, apparently transported through the atmosphere, began to appear in the mid-eighteenth century, and continued to the 1990s. Annak had a similar mercury history until the late 1960s when disposal of domestic sewage led to increased sediment and contaminant accumulation. The high input of mercury to Annak confirms that Sanikiluaq residents are exposed to mercury through native food sources. 39 refs., 7 figs., 3 tabs.

  8. Erosion and sediment deposition evaluation in two slopes under different tillage systems using the '137Cs fallout' technique

    International Nuclear Information System (INIS)

    Arthur, Robson C.J.; Oliveira, Roberto A.S.; Bacchi, Osny O.S.; Correchel, Vladia; Santos, Dileia S.; Sparovek, Gerd

    2007-01-01

    With the increasing of occupation of the Brazilian Cerrado a series of environmental problems followed by the deforestation as soil erosion and soil compaction are appearing, and many of than are being related to the CT used. The NT cropping system which is being adopted more recently in the 'cerrado' region, has revealed benefic to the soil, mainly in terms of soil erosion control. The objective of the present work was to analyze the effect of the No Tillage NT and Conventional Tillage CT systems on the erosion process and to measure the efficiency of the riparian forest in trapping the sediments produced by erosion coming from crop areas cultivated by both systems trough the technique of 137Cs 'fallout' redistribution analysis. The study was carried out in Goiatuba/GO in two sampling dowslope transects located in areas of CT and NT cropping systems. Samples were taken from five points in transects of 200 and 140 meters long respectively, as well as from three soil profiles of a 30 m transect in the downstream riparian forests of each area. Incremental depth samples were also taken from two pits inside each transect in the forest down to 40 and 60 cm depth for the CT and NT respectively. The soil samples were air dried and sieved and the 137 Cs activity was analyzed for in a gamma ray detector (GEM-20180P, EG and ORTEC) coupled to a multichannel analyzer at CENA/USP. The results indicate variation of 137 Cs in soil profiles and high erosion rates for both cropping areas also indicate a movement of sediments from the two cropping areas to the riparian forest. (author)

  9. Erosion and sediment deposition evaluation on slopes under different tillage systems in the Cerrado region using the 137Cs fallout technique

    International Nuclear Information System (INIS)

    Arthur, Robson Clayton Jacques

    2010-01-01

    In Brazil, the expansion of agricultural areas causes several problems on natural resources. With the increasing occupation of the Cerrado region by agriculture, a series of environmental problems like deforestation, soil erosion and soil compaction are appearing and causing radical transformations in the natural landscape due to removing almost all native vegetation. The conventional tillage system (CTS) is considered an inadequate form of soil management for its frequently irremediable consequences of soil compaction and soil erosion, and the no till system (NTS) makes the maintenance of the soil conditions possible, letting them close to the natural environment, thus reducing rates of soil erosion. The objective of this work was to evaluate the efficiency of riparian forests in the retention of sediments originated for three different tillage systems, through the fallout 137 CS redistribution technique, the Universal Soil Loss Equation (USLE) and some physical and chemical parameters that indicate the structural conditions of the soils of Goiatuba and Jandaia-GO. In the three areas, soil profiles were collected in three layers of 20 cm (0-20, 20-40 and 40-60 cm) at distinct points located along linear transects in the direction of the maximum slope until the riparian forest. In the riparian forest of each area, trenches were opened and soil was sampled to evaluate the activity of 137 Cs and the physical and chemical parameters of soil. Detection of the activity of 137 Cs was made with a gamma ray detector model (GEM-20180P, EG and ORTEC) connected to a multichannel analyzer. The comparison of averages was made using the Tukey test at 5% level of significance. The. results indicated that, the three soil tillage systems presented high rates of soil erosion and deposition of sediments and the riparian forest of the areas under CTS, NTS and pasture, located downstream received great amounts of sediments, and that only the riparian forest of CTS was capable to trap

  10. Assessment of the Efficiency of Sediment Deposition Reduction in the Zengwen River Watershed in Taiwan

    Science.gov (United States)

    Wu, M.; Tan, H. N.; Lo, W. C.; Tsai, C. T.

    2015-12-01

    The river upstream of watersheds in Taiwan is very steep, where soil and rock are often unstable so that the river watershed typically has the attribute of high sand yield and turbid runoff due to the excessive erosion in the heavy rainfall seasons. If flood water overflows the river bank, it would lead to a disaster in low-altitude plains. When flood retards or recesses, fine sediment would deposit. Over recent decades, many landslides arise in the Zengwen river watershed due to climate changes, earthquakes, and typhoons. The rocks and sands triggered by these landslides would move to the river channel through surface runoff, which may induce sediment disasters and also render an impact on the stability and sediment transport of the river channel. The risk of the sediment disaster could be reduced by implementing dredging works. However, because of the nature of the channel, the dredged river sections may have sediment depositions back; thus, causing an impact on flood safety. Therefore, it is necessary to evaluate the effectiveness of dredged works from the perspectives of hydraulic, sediment transport, and flood protection to achieve the objective of both disaster prevention and river bed stability. We applied the physiographic soil erosion-deposition (PSED) model to simulate the sediment yield, the runoff, and sediment transport rate of the Zengwen river watershed corresponding to one-day rainstorms of the return periods of 25, 50, and 100 year. The potential of sediment deposition and erosion in the river sections of the Zengwen river could be simulated by utilizing the alluvial river-movable bed two dimensional (ARMB-2D) model. The results reveal that the tendency for the potential of river sediment deposition and erosion obtained from these two models is agreeable. Furthermore, in order to evaluate the efficiency of sediment deposition reduction, two quantized values, the rate of sediment deposition reduction and the ratio of sediment deposition reduction

  11. Sedimentation Deposition Patterns on the Chukchi Shelf Using Radionuclide Inventories

    Science.gov (United States)

    Cooper, L. W.; Grebmeier, J. M.

    2016-02-01

    Sediment core collections and assays of the anthropogenic and natural radioisotopes, 137Cs and 210Pb, respectively, are providing long-term indications of sedimentation and current flow processes on the Chukchi and East Siberian sea continental shelf. This work, which has been integrated into interdisciplinary studies of the Chukchi Sea supported by both the US Bureau of Ocean Energy Management (COMIDA Hanna Shoal Project) and the National Oceanic and Atmospheric Administration (Russian-US Long Term Census of the Arctic, RUSALCA) includes studies of total radiocesium inventories, sedimentation rate determinations, where practical, and depths of maxima in radionuclide deposition. Shallow maxima in the activities of the anthropogenic radionuclide in sediment cores reflect areas with higher current flow (Barrow Canyon and Herald Canyon; 3-6 cm) or low sedimentation (Hanna Shoal; 1-3 cm). The first sedimentation studies from Long Strait are consistent with quiescent current conditions and steady recent sedimentation of clay particles. Elsewhere, higher and more deeply buried radionuclide inventories (> 2 mBq cm-2 at 15-17 cm depth) in the sediments correspond to areas of high particle deposition north of Bering Strait where bioturbation in productive sediments is also clearly an important influence. Radiocesium activities from bomb fallout dating to 1964 are now present at low levels (20 cm. Independent sedimentation rate measurements with the natural radionuclide 210Pb are largely consistent with the radiocesium measurements.

  12. Modeling transport and deposition of the Mekong River sediment

    Science.gov (United States)

    Xue, Zuo; He, Ruoying; Liu, J. Paul; Warner, John C.

    2012-01-01

    A Coupled Wave–Ocean–SedimentTransport Model was used to hindcast coastal circulation and fine sedimenttransport on the Mekong shelf in southeastern Asian in 2005. Comparisons with limited observations showed that the model simulation captured the regional patterns and temporal variability of surface wave, sea level, and suspended sediment concentration reasonably well. Significant seasonality in sedimenttransport was revealed. In summer, a large amount of fluvial sediments was delivered and deposited near the MekongRiver mouth. In the following winter, strong ocean mixing, and coastal current lead to resuspension and southwestward dispersal of a small fraction of previously deposited sediments. Model sensitivity experiments (with reduced physics) were performed to investigate the impact of tides, waves, and remotely forced ambient currents on the transport and dispersal of the fluvial sediment. Strong wave mixing and downwelling-favorable coastal current associated with the more energetic northeast monsoon in the winter season are the main factors controlling the southwestward along-shelf transport.

  13. Direct sampling during multiple sediment density flows reveals dynamic sediment transport and depositional environment in Monterey submarine canyon

    Science.gov (United States)

    Maier, K. L.; Gales, J. A.; Paull, C. K.; Gwiazda, R.; Rosenberger, K. J.; McGann, M.; Lundsten, E. M.; Anderson, K.; Talling, P.; Xu, J.; Parsons, D. R.; Barry, J.; Simmons, S.; Clare, M. A.; Carvajal, C.; Wolfson-Schwehr, M.; Sumner, E.; Cartigny, M.

    2017-12-01

    Sediment density flows were directly sampled with a coupled sediment trap-ADCP-instrument mooring array to evaluate the character and frequency of turbidity current events through Monterey Canyon, offshore California. This novel experiment aimed to provide links between globally significant sediment density flow processes and their resulting deposits. Eight to ten Anderson sediment traps were repeatedly deployed at 10 to 300 meters above the seafloor on six moorings anchored at 290 to 1850 meters water depth in the Monterey Canyon axial channel during 6-month deployments (October 2015 - April 2017). Anderson sediment traps include a funnel and intervalometer (discs released at set time intervals) above a meter-long tube, which preserves fine-scale stratigraphy and chronology. Photographs, multi-sensor logs, CT scans, and grain size analyses reveal layers from multiple sediment density flow events that carried sediment ranging from fine sand to granules. More sediment accumulation from sediment density flows, and from between flows, occurred in the upper canyon ( 300 - 800 m water depth) compared to the lower canyon ( 1300 - 1850 m water depth). Sediment accumulated in the traps during sediment density flows is sandy and becomes finer down-canyon. In the lower canyon where sediment directly sampled from density flows are clearly distinguished within the trap tubes, sands have sharp basal contacts, normal grading, and muddy tops that exhibit late-stage pulses. In at least two of the sediment density flows, the simultaneous low velocity and high backscatter measured by the ADCPs suggest that the trap only captured the collapsing end of a sediment density flow event. In the upper canyon, accumulation between sediment density flow events is twice as fast compared to the lower canyon; it is characterized by sub-cm-scale layers in muddy sediment that appear to have accumulated with daily to sub-daily frequency, likely related to known internal tidal dynamics also measured

  14. Accumulation rates and sediment deposition in the northwestern Mediterranean

    Science.gov (United States)

    Zuo, Z.; Eisma, D.; Gieles, R.; Beks, J.

    As part of the EROS 2000 programme, sediment mixing and accumulation rates in the northwestern Mediterranean Sea were determined, applying the 210Pb dating method to a total of 49 cores, and the results from 29 sediment cores are presented here. On the basis of the results from the 49 sediment cores, an attempt was made to present a general picture of sediment accumulation for the area of the northwestern Mediterranean. The total deposition of sediment in the area is estimated to be of the order of 34±15 × 106 ton year-1, which is half the value reported earlier by Got and Aloisi (1990) (Continental Shelf Research, 10, 841-855) for the same region. The activity-depth profiles of 210Pb show the presence of intensive mixing in the upper layer of near-shore sediments, but little or no mixing is observed in the deep-water sediments. Based on a diffusion model, sediment mixing rates calculated from excess 210Pb gradients vary from 0·002 to 7· cm2 year-1, and the deposition rates from 0·01 to 0·60 cm year-1. A linear dependence of sedimentation rate on water depth derived from the sediment cores indicates an inverse correlation between these two. The relatively high sedimentation rates and mixing rates found near the Rhône River suggest that the contribution from the river dominates the deposition system in the northwestern Mediterranean. In the deep-water basin, however, atmospheric input and biological production are clearly more important.

  15. Sediment Evaluation Framework for the Pacific Northwest

    Science.gov (United States)

    The Sediment Evaluation Framework provides a regional framework for assessment, characterization and management of sediments in the Pacific Northwest to determine suitability for unconfined in-water disposal.

  16. Avalanches of sediment form deep-marine depositions

    NARCIS (Netherlands)

    Pohl, Florian|info:eu-repo/dai/nl/34309424X

    2017-01-01

    The deep ocean is the largest sedimentary system basin on the planet. It serves as the primary storage point for all terrestrially weathered sediment that makes it beyond the near-shore environment. These deep-marine offshore deposits have become a focus of attention in exploration due to the

  17. Does deposition depth control the OSL bleaching of fluvial sediment?

    NARCIS (Netherlands)

    Cunningham, A. C.; Wallinga, J.; Hobo, N.; Versendaal, A. J.; Makaske, B.; Middelkoop, H.

    2014-01-01

    The Optically Stimulated Luminescence (OSL) signal from fluvial sediment often contains a remnant from the previous deposition cycle, leading to a partially bleached equivalent-dose distribution. Although identification of the burial dose is of primary concern, the degree of bleaching could

  18. Development of Sediment Deposition Height Capacity Equation in Sewer Networks

    Science.gov (United States)

    Song, Yangho; Jo, Deokjun; Lee, Jungho

    2017-04-01

    Sediment characteristics and transport processes in sewers are markedly different from river. There is a wide range of particle densities and smaller particle size variation in sewers. Sediment supply and the available erodible material are more limited in sewers, and the diverse hydraulic characteristics in sewer systems are more unsteady. Prevention of sewer sediment accumulation, which can cause major sewer operational problems, is imperative and has been an immense concern for engineers. The effects of sediment formation in sewer systems, an appropriate sediment transport modelling with the ability to determine the location and depth of sediment deposit is needed. It is necessary to design efficiently considering the transfer and settling phenomena of the sediment coming into the sewer systems. During transport in the sewer, the minimum shear flow velocity and possible shear stress at which the sediment is transported smoothly. However, the interaction of sediment and fluid within the sewer systems has been very complex and the rigorous theoretical handling of this problem has not been developed. It is derived from the empirical values obtained from the river bed. The basic theory that particles float is based on the balance between sedimentation of particles by gravity and turbulent diffusion of fluids. There are many variables related. Representative parameters include complex phenomena due to collisions between particles, particles and fluids, and interactions between particles and tube walls. In general, the main parameters that form the boundary between the main transport and sediment are particle size, density, volume fraction, pipe diameter and gravity. As the particle size and volume concentration increase, the minimum feed rate increases and the same tendency is observed for the change of the capillary diameter. Based on this tendency, this study has developed a sediment deposition height capacity formula to take into consideration the sewer discharge

  19. How are macroinvertebrates of slow flowing lotic systems directly affected by suspended and deposited sediments?

    Energy Technology Data Exchange (ETDEWEB)

    Kefford, Ben J., E-mail: ben.kefford@rmit.edu.a [Biotechnology and Environmental Biology, School of Applied Sciences, RMIT University, PO Box 71, Bundoora, Victoria 3083 (Australia); Zalizniak, Liliana [Biotechnology and Environmental Biology, School of Applied Sciences, RMIT University, PO Box 71, Bundoora, Victoria 3083 (Australia); Dunlop, Jason E. [Department of Environment and Resource Management (DERM), 120 Meiers Rd, Indooroopilly, Queensland 4068 (Australia); Smart Water Research Facility, Griffith University, Queensland (Australia); Nugegoda, Dayanthi [Biotechnology and Environmental Biology, School of Applied Sciences, RMIT University, PO Box 71, Bundoora, Victoria 3083 (Australia); Choy, Satish C. [Department of Environment and Resource Management (DERM), 120 Meiers Rd, Indooroopilly, Queensland 4068 (Australia)

    2010-02-15

    The effects of suspended and deposited sediments on the macroinvertebrates are well documented in upland streams but not in slower flowing lowland rivers. Using species found in lowland lotic environments, we experimentally evaluate mechanisms for sediments to affect macroinvertebrates, and in one experiment whether salinity alters the effect of suspended sediments. Suspended kaolin clay reduced feeding of Ischnura heterosticta (Odonata: Coenagrionidae) at high turbidity (1000-1500 NTU) but had no effects on feeding of Hemianax papuensis (Odonata: Aeshnidae) and Micronecta australiensis (Hemiptera: Corixidae). In freshwater (0.1 mS/cm), survival of Ischnura aurora was poor in clear water, but improved with suspended kaolin. Growth and feeding of I. aurora were unaffected by suspended sediments and salinity. Burial (1-5 mm) of eggs with kaolin or sand reduced hatching in Physa acuta (Gastropoda: Physidae), Gyraulus tasmanica (Gastropoda: Planorbidae) and Chironomus cloacalis (Diptera: Chironomidae). Settling sediments may pose greater risk to lowland lotic invertebrates than suspended sediments. - Sediment deposition may be more directly detrimental to macroinvertebrates of lowland rivers than suspended sediments.

  20. Exploiting virtual sediment deposits to explore conceptual foundations

    Science.gov (United States)

    Dietze, Michael; Fuchs, Margret; Kreutzer, Sebastian

    2017-04-01

    Geomorphic concepts and hypotheses are usually formulated based on empiric data from the field or the laboratory (deduction). After translation into models they can be applied to case study scenarios (induction). However, the other way around - expressing hypotheses explicitly by models and test these by empiric data - is a rarely touched trail. There are several models tailored to investigate the boundary conditions and processes that generate, mobilise, route and eventually deposit sediment in a landscape. Thereby, the last part, sediment deposition, is usually omitted. Essentially, there is no model that explicitly focuses on mapping out the characteristics of sedimentary deposits - the material that is used by many disciplines to reconstruct landscape evolution. This contribution introduces the R-package sandbox, a model framework that allows creating and analysing virtual sediment sections for exploratory, explanatory, forecasting and inverse research questions. The R-package sandbox is a probabilistic and rule-based model framework for a wide range of possible applications. The model framework is used here to discuss a set of conceptual questions revolving around geochemical and geochronological methods, such as: How does sample size and sample volume affect age uncertainty? What determines the robustness of sediment fingerprinting results? How does the prepared grain size of the material of interest affect the analysis outcomes? Most of the concepts used in geosciences are underpinned by a set of assumptions, whose robustness and boundary conditions need to be assessed quantitatively. The R-package sandbox is a universal and flexible tool to engage with this challenge.

  1. An acoustic method for predicting relative strengths of cohesive sediment deposits

    Science.gov (United States)

    Reed, A. H.; Sanders, W. M.

    2017-12-01

    Cohesive sediment dynamics are fundamentally determined by sediment mineralogy, organic matter composition, ionic strength of water, and currents. These factors work to bind the cohesive sediments and to determine depositional rates. Once deposited the sediments exhibit a nonlinear response to stress and they develop increases in shear strength. Shear strength is critically important in resuspension, transport, creep, and failure predictions. Typically, shear strength is determined by point measurements, both indirectly from free-fall penetrometers or directly on cores with a shear vane. These values are then used to interpolate over larger areas. However, the remote determination of these properties would provide continuos coverage, yet it has proven difficult with sonar systems. Recently, findings from an acoustic study on cohesive sediments in a laboratory setting suggests that cohesive sediments may be differentiated using parametric acoustics; this method pulses two primary frequencies into the sediment and the resultant difference frequency is used to determine the degree of acoustic nonlinearity within the sediment. In this study, two marine clay species, kaolinite and montmorillonite, and two biopolymers, guar gum and xanthan gum were mixed to make nine different samples. The samples were evaluated in a parametric acoustic measurement tank. From the parametric acoustic measurements, the quadratic nonlinearity coefficient (beta) was determined. beta was correlated with the cation exchange capacity (CEC), an indicator of shear strength. The results indicate that increased acoustic nonlinearity correlates with increased CEC. From this work, laboratory measurements indicate that this correlation may be used evaluate geotechnical properties of cohesive sediments and may provide a means to predict sediment weakness in subaqueous environments.

  2. Recent 137Cs deposition in sediments of Admiralty Bay, Antarctica

    International Nuclear Information System (INIS)

    Sanders, Christian J.; Santos, Isaac R.; Patchineelam, Sambasiva R.; Schaefer, Carlos; Silva-Filho, Emmanoel V.

    2010-01-01

    Cesium-137, radium-226 and lead-210 profiles of a 25 cm sediment core give an indication of recent changes in land-ocean interactions at a polar coastal environment (Admiralty Bay, King George Island, Antarctica). The linear sedimentation accumulation rate at the study site calculated from the unsupported 210 Pb profile was 6.7 mm/year from 1965 to 2005. A 3.5-fold increase in 137 Cs concentrations was observed in the top layer of this sediment core. This sharp increase seems to indicate a recent redistribution of fallout radionuclides previously deposited on soil, vegetation and snow. These results imply enhanced land-ocean interactions at this site likely as a result of climate change. Because our results are based on a single core, additional investigations are needed to confirm our observations.

  3. Entrainment, transport and deposition of sediment by saline gravity currents

    Science.gov (United States)

    Zordan, Jessica; Juez, Carmelo; Schleiss, Anton J.; Franca, Mário J.

    2018-05-01

    Few studies have addressed simultaneously the feedback between the hydrodynamics of a gravity current and the geomorphological changes of a mobile bed. Hydrodynamic quantities such as turbulent and mean velocities, bed shear stress and turbulent stresses undoubtedly govern the processes of entrainment, transport and deposition. On the other hand, the incorporation of entrained sediment in the current may change its momentum by introducing extra internal stresses, introducing thus a feedback process. These two main questions are here investigated. Laboratory experiments of saline gravity currents, produced by lock-exchange, flowing over a mobile bed channel reach, are here reported. Different initial buoyancies of the current in the lock are tested together with three different grain sizes of the non-coherent sediment that form the erodible bed. Results from velocity measurements are combined with the visualization of the sediment movement in the mobile reach and with post-test topographic and photo surveys of the geomorphology modifications of the channel bed. Mean and turbulent velocities are measured and bed shear stress and Reynolds stresses are estimated. We show that the mean vertical component of the velocity and bed shear stress are highly correlated with the first instants of sediment entrainment. Vertical turbulent velocity is similarly related to entrainment, although with lower correlation values, contributing as well to the sediment movement. Bed shear stress and Reynolds shear stress measured near the bed are correlated with sediment entrainment for longer periods, indicating that these quantities are associated to distal transport as well. Geomorphological changes in the mobile bed are strongly related to the impulse caused by the bed shear stress on the sediment. On the other hand, we show that the nature of the grain of the mobile bed reach influences the hydrodynamics of the current which means that a feedback mechanisms between both occurs during

  4. Design of a fuzzy differential evolution algorithm to predict non-deposition sediment transport

    Science.gov (United States)

    Ebtehaj, Isa; Bonakdari, Hossein

    2017-12-01

    Since the flow entering a sewer contains solid matter, deposition at the bottom of the channel is inevitable. It is difficult to understand the complex, three-dimensional mechanism of sediment transport in sewer pipelines. Therefore, a method to estimate the limiting velocity is necessary for optimal designs. Due to the inability of gradient-based algorithms to train Adaptive Neuro-Fuzzy Inference Systems (ANFIS) for non-deposition sediment transport prediction, a new hybrid ANFIS method based on a differential evolutionary algorithm (ANFIS-DE) is developed. The training and testing performance of ANFIS-DE is evaluated using a wide range of dimensionless parameters gathered from the literature. The input combination used to estimate the densimetric Froude number ( Fr) parameters includes the volumetric sediment concentration ( C V ), ratio of median particle diameter to hydraulic radius ( d/R), ratio of median particle diameter to pipe diameter ( d/D) and overall friction factor of sediment ( λ s ). The testing results are compared with the ANFIS model and regression-based equation results. The ANFIS-DE technique predicted sediment transport at limit of deposition with lower root mean square error (RMSE = 0.323) and mean absolute percentage of error (MAPE = 0.065) and higher accuracy ( R 2 = 0.965) than the ANFIS model and regression-based equations.

  5. The Effect of Suspended Sediment Transport and Deposition on Streambed Clogging Under Losing and Gaining Flow Conditions

    Science.gov (United States)

    Fox, A.; Packman, A. I.; Preziosi-Ribero, A.; Li, A.; Arnon, S.

    2017-12-01

    Sediment transport and deposition in streams can affect streambed hydraulic characteristics due to clogging, reduce water fluxes through the hyporheic zone, and thus expected to affect biogeochemical processes. Processes affecting deposition of suspended particles were systematically studied under various overlying velocities but without taking into account the interactions with groundwater. This is despite the fact that the interaction with groundwater were shown to play an important role in deposition patterns of fine sediments in field studies. The objective of this study was to evaluate the effect of losing and gaining fluxes on suspended sediment depositional patterns and on hyporheic exchange fluxes. Experiments were conducted in a laboratory flume system (640 cm long and 30 cm wide) that has a capacity to enforce losing or gaining flow conditions. The flume was packed with homogenous sand, while suspended sediment deposition was evaluated by adding kaolinite particles to the water and following the deposition rate by particle disappearance from the bulk water. Consecutive additions of kaolinite were done, while hyporheic exchange fluxes were evaluated by conducting NaCl tracer experiments between each kaolinite additions. Furthermore, dye injections were used to visualize the flow patterns in the streambed using time-lapse photography through the transparent sidewalls of the flume. Hyporheic exchange and particle tracking simulations were done to assess the results of particle deposition and feedbacks between hyporheic flow, particle transport, and streambed clogging. Experimental results showed that the deposition of clay decreases with increasing amount of clay concentration in the sediment. Hyporheic exchange flux decreases linearly with increasing amount of clay added to the system and the region of active hyporheic exchange was confined to the upper part of the sediment. Understanding the particle deposition mechanisms under losing and gaining flow

  6. Analysis of heavy metals in road-deposited sediments.

    Science.gov (United States)

    Herngren, Lars; Goonetilleke, Ashantha; Ayoko, Godwin A

    2006-07-07

    Road-deposited sediments were analysed for heavy metal concentrations at three different landuses (residential, industrial, commercial) in Queensland State, Australia. The sediments were collected using a domestic vacuum cleaner which was proven to be highly efficient in collecting sub-micron particles. Five particle sizes were analysed separately for eight heavy metal elements (Zn, Fe, Pb, Cd, Cu, Cr, Al and Mn). At all sites, the maximum concentration of the heavy metals occurred in the 0.45-75 microm particle size range, which conventional street cleaning services do not remove efficiently. Multicriteria decision making methods (MCDM), PROMETHEE and GAIA, were employed in the data analysis. PROMETHEE, a non-parametric ranking analysis procedure, was used to rank the metal contents of the sediments sampled at each site. The most polluted site and particle size range were the industrial site and the 0.45-75 microm range, respectively. Although the industrial site displayed the highest metal concentrations, the highest heavy metal loading coincided with the highest sediment load, which occurred at the commercial site. GAIA, a special form of principal component analysis, was applied to determine correlations between the heavy metals and particle size ranges and also to assess possible correlation with total organic carbon (TOC). The GAIA-planes revealed that irrespective of the site, most of the heavy metals are adsorbed to sediments below 150 microm. A weak correlation was found between Zn, Mn and TOC at the commercial site. This could lead to higher bioavailability of these metals through complexation reactions with the organic species in the sediments.

  7. Measurement of Sediment Deposition Rates using an Optical Backscatter Sensor

    Science.gov (United States)

    Ridd, P.; Day, G.; Thomas, S.; Harradence, J.; Fox, D.; Bunt, J.; Renagi, O.; Jago, C.

    2001-02-01

    An optical method for measuring siltation of sediment has been developed using an optical fibre backscatter (OBS) nephelometer. Sediment settling upon the optical fibre sensor causes an increase in the backscatter reading which can be related to the settled sediment surface density (SSSD) as measured in units of mg cm -2. Calibration and laboratory tests indicate that the resolution of measurements of SSSD is 0·01 mg cm -2and an accuracy of 5% in still water. In moving water it is more difficult to determine the accuracy of the method because other methods with suitable resolution are unavailable. However, indirect methods using measurements of changing suspended sediment concentration in a ring flume, indicate that the OBS method under-predicts deposition. The series of siltation from three field sites are presented. This sensor offers considerable advances over other methods of measuring settling because time series of settling may be taken and thus settling events may be related to other hydrodynamic parameters such as wave climate and currents.

  8. Middle Pleistocene infill of Hinkley Valley by Mojave River sediment and associated lake sediment: Depositional architecture and deformation by strike-slip faults

    Science.gov (United States)

    Miller, David; Haddon, Elizabeth; Langenheim, Victoria; Cyr, Andrew J.; Wan, Elmira; Walkup, Laura; Starratt, Scott W.

    2018-01-01

    Hinkley Valley in the Mojave Desert, near Barstow about 140 km northeast of Los Angeles and midway between Victorville Valley and the Lake Manix basin, contains a thick sedimentary sequence delivered by the Mojave River. Our study of sediment cores drilled in the valley indicates that Hinkley Valley was probably a closed playa basin with stream inflow from four directions prior to Mojave River inflow. The Mojave River deposited thick and laterally extensive clastic wedges originating from the southern valley that rapidly filled much of Hinkley Valley. Sedimentary facies representing braided stream, wetland, delta, and lacustrine depositional environments all are found in the basin fill; in some places, the sequence is greater than 74 m (245 ft) thick. The sediment is dated in part by the presence of the ~631 ka Lava Creek B ash bed low in the section, and thus represents sediment deposition after Victorville basin was overtopped by sediment and before the Manix basin began to be filled. Evidently, upstream Victorville basin filled with sediment by about 650 ka, causing the ancestral Mojave River to spill to the Harper and Hinkley basins, and later to Manix basin.Initial river sediment overran wetland deposits in many places in southern Hinkley Valley, indicating a rapidly encroaching river system. These sediments were succeeded by a widespread lake (“blue” clay) that includes the Lava Creek B ash bed. Above the lake sediment lies a thick section of interlayered stream sediment, delta and nearshore lake sediment, mudflat and/or playa sediment, and minor lake sediment. This stratigraphic architecture is found throughout the valley, and positions of lake sediment layers indicate a successive northward progression in the closed basin. A thin overlapping sequence at the north end of the valley contains evidence for a younger late Pleistocene lake episode. This late lake episode, and bracketing braided stream deposits of the Mojave River, indicate that the river

  9. Risk assessment of metals in road-deposited sediment along an urban–rural gradient

    International Nuclear Information System (INIS)

    Zhao, Hongtao; Li, Xuyong

    2013-01-01

    We applied the traditional risk assessment methods originally designed for soils and river sediments to evaluation of risk associated with metals in road-deposited sediment (RDS) along an urban–rural gradient that included central urban (UCA), urban village (UVA), central suburban county (CSA), rural town (RTA), and rural village (RVA) areas in the Beijing metropolitan region. A new indicator RI RDS was developed which integrated the RDS characteristics of mobility, grain size and amount with the potential ecological risk index. The risk associated with metals in RDS in urban areas was generally higher than that in rural areas based on the assessment using traditional methods, but the risk was higher in urban and rural village areas than the areas with higher administration units based on the indicator RI RDS . These findings implied that RDS characteristics variation with the urban–rural gradient must be considered in metal risk assessment and RDS washoff pollution control. Highlights: ► Spatial pattern of metal risk level associated with road-deposited sediment (RDS) along urban–rural gradients varied. ► Risk level of metals changed significantly when grain size was considered. ► A new index integrating RDS characteristics and potential ecological risk was developed. ► Results from the new index were improved relative to those of traditional assessment methods. -- A new index integrating road-deposited sediment characteristics and potential ecological risk was developed to assess metal risk along the urban–rural gradient

  10. Net atmospheric mercury deposition to Svalbard: Estimates from lacustrine sediments

    Science.gov (United States)

    Drevnick, Paul E.; Yang, Handong; Lamborg, Carl H.; Rose, Neil L.

    2012-11-01

    In this study we used lake sediments, which faithfully record Hg inputs, to derive estimates of net atmospheric Hg deposition to Svalbard, Norwegian Arctic. With the exception of one site affected by local pollution, the study lakes show twofold to fivefold increases in sedimentary Hg accumulation since 1850, likely due to long-range atmospheric transport and deposition of anthropogenic Hg. Sedimentary Hg accumulation in these lakes is a linear function of the ratio of catchment area to lake area, and we used this relationship to model net atmospheric Hg flux: preindustrial and modern estimates are 2.5 ± 3.3 μg m-2 y-1 and 7.0 ± 3.0 μg m-2 y-1, respectively. The modern estimate, by comparison with data for Hg wet deposition, indicates that atmospheric mercury depletion events (AMDEs) or other dry deposition processes contribute approximately half (range 0-70%) of the net flux. Hg from AMDEs may be moving in significant quantities into aquatic ecosystems, where it is a concern because of contamination of aquatic food webs.

  11. Numerical Modelling of Suspended Transport and Deposition of Highway Deposited Sediments

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby; Larsen, Torben; Bach, Christine

    Good data for calibration and validation of numerical models are of high importance. In the natural environment data can be hard to archive and the stochastic nature have governing influence on the data archived. Hence for modelling of suspended transport and deposition of particles, originating ...... from the highway surfaces, in highway detention ponds, four experiments are carried out. To simplify the complexity of a real pond and for easy control and measurement the sediment transports where carried out in two rectangular channels....

  12. 3D Modelling of Transport, Deposition and Resuspension of Highway Deposited Sediments in wet Detention Ponds

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby

    2010-01-01

    concrete channel with width of 0.8m and a water depth of approximately 0.8m and in circular flume experiments in order to reproduce near-bed specific processes such as resuspension and consolidation. With a fairly good agreement with measurements, modelling of hydrodynamics, transport of dissolved...... pollutants and particles in wet detention ponds is possible with application of a three dimensional RANS model and the advection/dispersion equation taken physical phenomena like wind, waves, deposition, erosion and consolidation of the bottom sediment into account....

  13. Numerical simulation of sediment deposition thickness at Beidaihe International Yacht Club

    Directory of Open Access Journals (Sweden)

    Cheng-gang Lu

    2010-09-01

    Full Text Available The finite element method (FEM was used to simulate sediment hydrodynamics at the Beidaihe International Yacht Club, and a two-dimensional model was established. The sediment movement and deposition were analyzed under many tidal conditions in conjunction with the hydrological regime of the Daihe River. The peak value of the sediment deposition thickness appears in the main channel and around the estuary. The sediment deposition thickness is essentially constant and relatively small in the project area. The sediment deposition thickness in the main channel, in the yachting area, and around the hotel is greater than the other areas in the project. Regular excavation and dredging of the channel is the best measure for mitigating the sedimentation.

  14. Investigations of contaminated fluvial sediment deposits: merging of statistical and geomorphic approaches.

    Science.gov (United States)

    Ryti, Randall T; Reneau, Steven L; Katzman, Danny

    2005-05-01

    Concentrations of contaminants in sediment deposits can have large spatial variability resulting from geomorphic processes acting over long time periods. Thus, systematic (e.g., regularly spaced sample locations) or random sampling approaches might be inefficient and/or lead to highly biased results. We demonstrate the bias associated with systematic sampling and compare these results to those achieved by methods that merge a geomorphic approach to evaluating the physical system and stratified random sampling concepts. By combining these approaches, we achieve a more efficient and less biased characterization of sediment contamination in fluvial systems. These methods are applied using a phased sampling approach to characterize radiological contamination in sediment deposits in two semiarid canyons that have received historical releases from the Los Alamos National Laboratory. Uncertainty in contaminant inventory was used as a metric to evaluate the adequacy of sampling during these phased investigations. Simple, one-dimensional Monte Carlo simulations were used to estimate uncertainty in contaminant inventory. We also show how one can use stratified random sampling theory to help estimate uncertainty in mean contaminant concentrations.

  15. Formation of banded vegetation patterns resulted from interactions between sediment deposition and vegetation growth.

    Science.gov (United States)

    Huang, Tousheng; Zhang, Huayong; Dai, Liming; Cong, Xuebing; Ma, Shengnan

    2018-03-01

    This research investigates the formation of banded vegetation patterns on hillslopes affected by interactions between sediment deposition and vegetation growth. The following two perspectives in the formation of these patterns are taken into consideration: (a) increased sediment deposition from plant interception, and (b) reduced plant biomass caused by sediment accumulation. A spatial model is proposed to describe how the interactions between sediment deposition and vegetation growth promote self-organization of banded vegetation patterns. Based on theoretical and numerical analyses of the proposed spatial model, vegetation bands can result from a Turing instability mechanism. The banded vegetation patterns obtained in this research resemble patterns reported in the literature. Moreover, measured by sediment dynamics, the variation of hillslope landform can be described. The model predicts how treads on hillslopes evolve with the banded patterns. Thus, we provide a quantitative interpretation for coevolution of vegetation patterns and landforms under effects of sediment redistribution. Copyright © 2018. Published by Elsevier Masson SAS.

  16. Functional trait responses to sediment deposition reduce macrofauna-mediated ecosystem functioning in an estuarine mudflat

    Science.gov (United States)

    Mestdagh, Sebastiaan; Bagaço, Leila; Braeckman, Ulrike; Ysebaert, Tom; De Smet, Bart; Moens, Tom; Van Colen, Carl

    2018-05-01

    Human activities, among which dredging and land use change in river basins, are altering estuarine ecosystems. These activities may result in changes in sedimentary processes, affecting biodiversity of sediment macrofauna. As macrofauna controls sediment chemistry and fluxes of energy and matter between water column and sediment, changes in the structure of macrobenthic communities could affect the functioning of an entire ecosystem. We assessed the impact of sediment deposition on intertidal macrobenthic communities and on rates of an important ecosystem function, i.e. sediment community oxygen consumption (SCOC). An experiment was performed with undisturbed sediment samples from the Scheldt river estuary (SW Netherlands). The samples were subjected to four sedimentation regimes: one control and three with a deposited sediment layer of 1, 2 or 5 cm. Oxygen consumption was measured during incubation at ambient temperature. Luminophores applied at the surface, and a seawater-bromide mixture, served as tracers for bioturbation and bio-irrigation, respectively. After incubation, the macrofauna was extracted, identified, and counted and then classified into functional groups based on motility and sediment reworking capacity. Total macrofaunal densities dropped already under the thinnest deposits. The most affected fauna were surficial and low-motility animals, occurring at high densities in the control. Their mortality resulted in a drop in SCOC, which decreased steadily with increasing deposit thickness, while bio-irrigation and bioturbation activity showed increases in the lower sediment deposition regimes but decreases in the more extreme treatments. The initial increased activity likely counteracted the effects of the drop in low-motility, surficial fauna densities, resulting in a steady rather than sudden fall in oxygen consumption. We conclude that the functional identity in terms of motility and sediment reworking can be crucial in our understanding of the

  17. Functional trait responses to sediment deposition reduce macrofauna-mediated ecosystem functioning in an estuarine mudflat

    Directory of Open Access Journals (Sweden)

    S. Mestdagh

    2018-05-01

    Full Text Available Human activities, among which dredging and land use change in river basins, are altering estuarine ecosystems. These activities may result in changes in sedimentary processes, affecting biodiversity of sediment macrofauna. As macrofauna controls sediment chemistry and fluxes of energy and matter between water column and sediment, changes in the structure of macrobenthic communities could affect the functioning of an entire ecosystem. We assessed the impact of sediment deposition on intertidal macrobenthic communities and on rates of an important ecosystem function, i.e. sediment community oxygen consumption (SCOC. An experiment was performed with undisturbed sediment samples from the Scheldt river estuary (SW Netherlands. The samples were subjected to four sedimentation regimes: one control and three with a deposited sediment layer of 1, 2 or 5 cm. Oxygen consumption was measured during incubation at ambient temperature. Luminophores applied at the surface, and a seawater–bromide mixture, served as tracers for bioturbation and bio-irrigation, respectively. After incubation, the macrofauna was extracted, identified, and counted and then classified into functional groups based on motility and sediment reworking capacity. Total macrofaunal densities dropped already under the thinnest deposits. The most affected fauna were surficial and low-motility animals, occurring at high densities in the control. Their mortality resulted in a drop in SCOC, which decreased steadily with increasing deposit thickness, while bio-irrigation and bioturbation activity showed increases in the lower sediment deposition regimes but decreases in the more extreme treatments. The initial increased activity likely counteracted the effects of the drop in low-motility, surficial fauna densities, resulting in a steady rather than sudden fall in oxygen consumption. We conclude that the functional identity in terms of motility and sediment reworking can be crucial in our

  18. Zinc and cadmium mobility in a 5-year-old dredged sediment deposit: experiments and modelling

    Energy Technology Data Exchange (ETDEWEB)

    Lions, J. [BRGM, Orleans (France). Water Div.; Centre National de Recherche sur les Sites et Sols Pollues, Douai (France); Lee, J. van der [Ecole des Mines de Paris, Fontainebleau (France). Geosciences - Reactive Hydrodynamics Group; Guerin, V.; Bataillard, P. [BRGM, Orleans (France). Environment and Process Div.; Centre National de Recherche sur les Sites et Sols Pollues, Douai (France); Laboudigue, A. [Ecole des Mines de Douai (France). Environmental and Civil Engineering; Centre National de Recherche sur les Sites et Sols Pollues, Douai (France)

    2007-08-15

    Background. Landfill deposits of contaminated, dredged sediments are subject to chemical alteration and especially to oxidation processes. Accordingly, sulphides are gradually oxidized leading to the formation of secondary phases and associated metals could become mobile and redistributed among the sediment components, such as carbonates, clay and freshly precipitated (hydr)oxides. Once mobilised, metals could represent a hazard for the environment and especially for drinking water supply facilities. Methods. In the present study, leaching experiments have been carried out on a dredged sediment to study metal mobilisation after 5 years of field aging. First, kinetic batch tests allowed one to evaluate the impact of solid-liquid contact time and to determine the kinetic parameters. Secondly, two types of dynamic experiments have been conducted: dynamic flush reactor and column leach test to evaluate the impact of solution renewing by excluding or not excluding the transport processes, respectively. In order to evaluate the impact of calcium on the metal mobilisation, the column leaching test is conducted with pure water and Ca(NO{sub 3}){sub 2} solution, at the beginning and at the end of the injection, respectively. Geochemical and reactive transport modelling of the experiments was performed using the geochemical code CHESS and the reactive transport model HYTEC. Results and Discussion. The studied sediment is complex with numerous reactive phases such as sulphides, (hydr)oxides, organic matter, phyllosilicates. All leaching tests highlight that zinc and cadmium are mobilised in significant concentrations and lead remains insoluble. A conceptual geochemical model of the sediment has been built to allow simulations of the whole experiments, based on a single, coherent phase description and parameter set. Simulations of the batch, flush and column experiments were performed taking into account the major reaction-controlling mechanisms including, among others, p

  19. Evaluation of an Empirical Reservoir Shape Function to Define Sediment Distributions in Small Reservoirs

    Directory of Open Access Journals (Sweden)

    Bogusław Michalec

    2015-08-01

    Full Text Available Understanding and defining the spatial distribution of sediment deposited in reservoirs is essential not only at the design stage but also during the operation. The majority of research concerns the distribution of sediment deposition in medium and large water reservoirs. Most empirical methods do not provide satisfactory results when applied to the determination of sediment deposition in small reservoirs. Small reservoir’s volumes do not exceed 5 × 106 m3 and their capacity-inflow ratio is less than 10%. Long-term silting measurements of three small reservoirs were used to evaluate the method described by Rahmanian and Banihashemi for predicting sediment distributions in small reservoirs. Rahmanian and Banihashemi stated that their model of distribution of sediment deposition in water reservoir works well for a long duration operation. In the presented study, the silting rate was used in order to determine the long duration operation. Silting rate is a quotient of volume of the sediment deposited in the reservoir and its original volume. It was stated that when the silting rate had reached 50%, the sediment deposition in the reservoir may be described by an empirical reservoir depth shape function (RDSF.

  20. Sedimentation rates in eastern North America reveal strong links between regional climate, depositional environments, and sediment accumulation

    Science.gov (United States)

    Goring, S. J.; McLachlan, J. S.; Jackson, S. T.; Blaauw, M.; Christen, J.; Marlon, J.; Blois, J.; Williams, J. W.

    2011-12-01

    PalEON is a multidisciplinary project that combines paleo and modern ecological data with state-of-the-art statistical and modelling tools to examine the interactions between climate, fire and vegetation during the past two millennia in the northeastern United States. A fundamental challenge for PalEON (and paleo research more broadly) is to improve age modelling to yield more accurate sediment-core chronologies. To address this challenge, we assessed sedimentation rates and their controls for 218 lakes and mires in the northeastern U.S. Sedimentation rates (yr/cm) were calculated from age-depth models, which were obtained from the Neotoma database (www.neotomadb.org) and other contributed pollen records. The age models were recalibrated to IntCal09 and augmented in some cases using biostratigraphic markers (Picea decline, 16 kcal BP - 10.5 kcal BP; Quercus rise, 12 - 9.1 kcal BP; and Alnus decline, 11.5 - 10.6 kcal BP) as described in Blois et al. (2011). Relationships between sedimentation rates and sediment age, site longitude, and depositional environment (lacustrine or mire) are significant but weak. There are clear and significant links between variations in the NGRIP record of δ18O and sedimentation in mires across the PalEON region, but no links to lacustrine sedimentation rates. This result indicates that super-regional climatic control of primary productivity, and thus autochthonic sediment deposition, dominates in mires while deposition in lacustrine basins may be driven primarily by local and regional factors including watershed size, surficial materials,and regional vegetation. The shape of the gamma probability functions that best describe sedimentation rate distributions are calculated and presented here for use as priors in Bayesian age modelling applications such as BACON (Blaauw and Christen, in press). Future applications of this research are also discussed.

  1. Distributing Characteristics of Heavy Metal Elements in A Tributary of Zhedong River in Laowangzhai Gold Deposit, Yunnan (China): An Implication to Environmentology from Sediments

    Science.gov (United States)

    Yang, Shuran; Danĕk, Tomáš; Yang, Xiaofeng; Cheng, Xianfeng

    2016-10-01

    Five heavy metal contents from five sediments and seven sediment profiles in an upstream reach of Zhedong river in Laowangzhai gold deposit were investigated in this research, along with analysis of the horizontal distribution, the surface distribution, the vertical distribution and the interlayer distribution of five heavy metal contents: arsenic (As), mercury (Hg), copper (Cu), lead (Pb) and zinc (Zn). The potential ecological risk of five heavy metals was evaluated to help understanding pollution control of Laowangzhai deposit.

  2. Kinematics of flow and sediment particles at entrainment and deposition

    Science.gov (United States)

    Antico, Federica; Sanches, Pedro; Aleixo, Rui; Ferreira, Rui M. L.

    2015-04-01

    A cohesionless granular bed subjected to a turbulent open-channel flow is analysed. The key objective is to clarify the kinematics of entrainment and deposition of individual sediment particles. In particular, we quantify a) the turbulent flow field in the vicinity of particles at the instants of their entrainment and of their deposition; b) the initial particle velocity and the particle velocity immediately before returning to rest. The experimental work was performed at the Hydraulics Laboratory of IST-UL in a 12.5 m long, 0.405 m wide glass-walled flume recirculating water and sediment through independent circuits. The granular bed was a 4.0 m long and 2.5 cm deep reach filled with 5 mm diameter glass beads packed (with some vibration) to a void fraction of 0.356, typical of random packing. Upstream the mobile bed reach the bed was composed of glued particles to ensure the development of a boundary layer with the same roughness. Laboratory tests were run under conditions of weak beadload transport with Shields parameters in the range 0.007 to 0.03. Froude numbers ranged from 0.63 to 0.95 while boundary Reynolds numbers were in the range 130 to 300. It was observed that the bed featured patches of regular arrangements: face centered cubic (fcc) or hexagonal close packing (hcp) blocks alternate with and body centered cubic (bcc) blocks. The resulting bed surface exhibits cleavage lines between blocks and there are spatial variations of bed elevation. The option for artificial sediment allowed for a simplified description of particle positioning at the instant of entrainment. In particular support and pivoting angles are found analytically. Skin friction angles were determind experimentally. The only relevant variables are exposure (defined as the ratio of the actual frontal projection of the exposed area to the area of a circle with 5 mm diameter) and protrusion (defined as the vertical distance between the apex of the particle and the mean local bed elevation

  3. Impact of beaver ponds on river discharge and sediment deposition along the Chevral River, Ardennes, Belgium

    Science.gov (United States)

    Nyssen, Jan; Frankl, Amaury; Pontzeele, Jolien; De Visscher, Maarten; Billi, Paolo

    2013-04-01

    With the recovery of the European beaver (Castor fiber) and their capacity to engineer fluvial landscapes, questions arise as to how they influence river discharge and sediment transport. The Chevral river (Ardennes, Belgium) contains two beaver dam sequences which appeared in 2004 and count now about 30 dams. Flow discharges and sediment fluxes were measured at the in- and outflow of each dam sequence. Volumes of sediment deposited behind the dams were measured. Between 2004 and 2011, peak flows were topped off, and the magnitude of extreme events decreased. 1710 m³ of sediment were deposited behind the beaver dams, with an average sediment thickness of 25 cm. The thickness of the sediment layer is related to the area of the beaver ponds. Along the stream, beaver pond sediment thickness displayed a sinusoidal deposition pattern, in which ponds with thick sediment layers were preceded by a series of ponds with thinner sediment layers. A downstream textural coarsening in the dam sequences was also observed, probably due to dam failures subsequent to surges. Differences in sediment flux between the in- and outflow at the beaver pond sequence were related to the river hydrograph, with deposition taking place during the rising limbs and slight erosion during the falling limbs. The seven-year-old sequences have filtered 190 tons of sediment out of the Chevral river, which is of the same order of magnitude as the 374 tons measured in pond deposits, with the difference between the values corresponding to beaver excavations (60 tons), inflow from small tributaries, and runoff from the valley flanks. Hydrogeomorphic effects of C. fiber and C. canadensis activity are similar in magnitude. The detailed analysis of changes to hydrology in beaver pond sequences confirms the potential of beavers to contribute to river and wetland restoration and catchment management.

  4. Sedimentation rates and depositional processes in Lake Superior from 210Pb geochronology

    International Nuclear Information System (INIS)

    Evans, J.E.; Johnson, T.C.; Alexander, E.C. Jr.; Lively, R.S.; Eisenreich, S.J.

    1981-01-01

    Sedimentation rates range from 0.01 to 0.32 cm/yr in 17 sediment box cores from Lake Superior, as determined by 210 Pb geochronology. Shoreline erosion and resuspension of nearshore sediments causes moderate to high (0.05-0.11 cm/yr) sedimentation rates in the western arm of Lake Superior. Sedimentation rates are very high (> 0.15 cm/yr) in marginal bays adjoining Lake Superior; and moderate to very high (0.07-0.19 cm/yr) in open lake regions adjacent to marginal bays. Resuspension of nearshore and shoal top sediments in southern and southeastern Lake Superior by storms is responsible for depositional anomalies in 210 Pb profiles corresponding to 1905, 1916-1918, and 1940 storms. Sedimentation rates are very low (0.01-0.03 cm/yr) in the central basins due to isolation from sediment sources. These data indicate that sedimentation rates and processes vary significantly in different regions of Lake Superior. The sedimentation rates provided by this study, in conjunction with previously-reported sedimentation rates, yield a better understanding of the Lake Superior depositional environment

  5. Environmental and geochemical assessment of surface sediments on irshansk ilmenite deposit area

    Directory of Open Access Journals (Sweden)

    Наталия Олеговна Крюченко

    2015-03-01

    Full Text Available It is revealed the problem of pollution of surface sediments of Irshansk ilmenite deposit area of various chemical elements hazard class (Mn, V, Ba, Ni, Co, Cr, Mo, Cu, Pb, Zn. It is determined its average content in surface sediments of various functional areas (forest and agricultural land, flood deposits, reclaimed land, calculated geochemical criteria, so given ecological and geochemical assessment of area

  6. Bioassessment metrics and deposited sediments in tributaries of the Chattooga river watershed

    Science.gov (United States)

    Erica Chiao; J. Bruce Wallace

    2003-01-01

    Excessive sedimentation places waters of the Chattooga River network at risk of biological impairment. Monitoring efforts could be improved by including metrics that are responsive to changes in levels of fine sediments. We sampled three habitats (riffle, depositional, bedrock outcrop) for benthic macroinvertebrates at four sites in three low-order, tributary reaches...

  7. Atmospheric deposition, water-quality, and sediment data for selected lakes in Mount Rainer, North Cascades, and Olympic National Parks, Washington, 2008-10

    Science.gov (United States)

    Sheibley, Rich W.; Foreman, James R.; Moran, Patrick W.; Swarzenski, Peter W.

    2012-01-01

    To evaluate the potential effect from atmospheric deposition of nitrogen to high-elevation lakes, the U.S. Geological Survey partnered with the National Park Service to develop a "critical load" of nitrogen for sediment diatoms. A critical load is defined as the level of a given pollutant (in this case, nitrogen) at which detrimental effects to a target endpoint (sediment diatoms) result. Because sediment diatoms are considered one of the "first responders" to ecosystem changes from nitrogen, they are a sensitive indicator for nitrogen deposition changes in natural areas. This report presents atmospheric deposition, water quality, sediment geochronology, and sediment diatom data collected from July 2008 through August 2010 in support of this effort.

  8. Formation of fine sediment deposit from a flash flood river in the Mediterranean Sea

    Science.gov (United States)

    Grifoll, Manel; Gracia, Vicenç; Aretxabaleta, Alfredo L.; Guillén, Jorge; Espino, Manuel; Warner, John C.

    2014-01-01

    We identify the mechanisms controlling fine deposits on the inner-shelf in front of the Besòs River, in the northwestern Mediterranean Sea. This river is characterized by a flash flood regime discharging large amounts of water (more than 20 times the mean water discharge) and sediment in very short periods lasting from hours to few days. Numerical model output was compared with bottom sediment observations and used to characterize the multiple spatial and temporal scales involved in offshore sediment deposit formation. A high-resolution (50 m grid size) coupled hydrodynamic-wave-sediment transport model was applied to the initial stages of the sediment dispersal after a storm-related flood event. After the flood, sediment accumulation was predominantly confined to an area near the coastline as a result of preferential deposition during the final stage of the storm. Subsequent reworking occurred due to wave-induced bottom shear stress that resuspended fine materials, with seaward flow exporting them toward the midshelf. Wave characteristics, sediment availability, and shelf circulation determined the transport after the reworking and the final sediment deposition location. One year simulations of the regional area revealed a prevalent southwestward average flow with increased intensity downstream. The circulation pattern was consistent with the observed fine deposit depocenter being shifted southward from the river mouth. At the southern edge, bathymetry controlled the fine deposition by inducing near-bottom flow convergence enhancing bottom shear stress. According to the short-term and long-term analyses, a seasonal pattern in the fine deposit formation is expected.

  9. Morphological resilience to flow fluctuations of fine sediment deposits in bank lateral cavities

    Science.gov (United States)

    Juez, C.; Thalmann, M.; Schleiss, A. J.; Franca, M. J.

    2018-05-01

    Lateral cavities are built in the banks of rivers for several purposes: to create harbors, to capture sediment, to keep a central navigable channel (i.e., Casiers de Girardon in the Rhone river) or to promote the formation of aquatic habitats if a limited amount of sediment is captured, providing hydraulic and morphologic diversity (i.e., the case of Japanese Wandos). This work is focused on this latter purpose: promotion of hydraulic and morphologic diversity. In these scenarios, an increase in the flow discharge in the main channel may, however, re-mobilize the deposit of sediment inside these lateral embayments and cause a sudden increase of the sediment concentration and turbidity in the main channel. It is thus of interest to characterize the resistance and resilience of these sedimentary deposits when the main channel is subjected to high flow or flushing events. Laboratory tests were carried out for five different normalized geometries of the cavities installed in the banks of an open channel and for five hydrographs with different levels of unsteadiness. Water depth, sediment deposit mass, sediment concentration and area covered by the settled sediments were recorded throughout each experiment. Although sediment deposits established at equilibrium before the flushing events are different depending on the geometry of the cavities, generally, they are recovered after being flushed by the high flow events. It is shown that the resistance and resilience of the sediment deposits are strongly dependent on the flow field and the mass exchange between the main channel and the cavities. This mass exchange is governed by the geometry of the cavities and the magnitude of the hydrographs applied.

  10. Numerical simulation of sediment movement and deposition in a meandering channel

    International Nuclear Information System (INIS)

    Ghani, U.

    2011-01-01

    In this research work, predictions have been made for the transport and deposition of incoming sediments in an open channel. Attempt has been made to understand the behavior of sediments flowing in the channel. The geometry consisted of a meandering compound channel with a constant inflow of sediments. For this purpose, 3D version of CFD (Computational Fluid Dynamics) code FLUENT has been used as a research tool. The turbulence closure of Reynolds Averaged Navior-Stokes equation was performed with standard -turbulence model. The Lagrangian particle tracking technique available in the code has been used for modeling sediment movement and deposition. For this purpose, nine different ranges of the particle diameters were released at the inlet of the channel. Initially, the model was validated using point velocities in the downstream direction and discharge values at five cross sections along the meander wavelength. The channel used for simulation purposes had a rectangular section. Once the model validated, it was then used for simulation of sediments. The numerical modeling gave a detailed picture of sediment deposited and transported through the channel. As the model was used with - turbulence model and Lagrangian particle tracking technique and then validated, it showed that when this combination of particle tracking and turbulence closure option will be used, the prediction will be fairly good and trustworthy. A number of numerical experiments were conducted to get the impact of sediment inflow velocity and its diameter on deposition patterns. It showed that boundary shearing stresses and secondary flows had considerable impact on sediment deposition in a river bend. The current study revealed that CFD technique can be used for predicting sediment distribution patterns with reasonable confidence. Such prediction techniques are not only economical but also provide details of complex flow and sediment movement behavior which are difficult to get through

  11. Cumulative history recorded in the depth distribution of radiocesium in sediments deposited on a sandbar

    International Nuclear Information System (INIS)

    Tanaka, Kazuya; Kondo, Hiroaki; Sakaguchi, Aya; Takahashi, Yoshio

    2015-01-01

    We collected sediments deposited on a sandbar from the surface to 20 cm in depth in the Abukuma River to clarify the history of radiocesium derived from the Fukushima Daiichi Nuclear Power Plant (FDNPP) accident. We analyzed the "1"3"7Cs concentration in the sediments from size-fractioned samples as well as bulk samples. The depth distribution of "1"3"7Cs showed the highest concentration in the deepest sediment layer (18–20 cm) studied, which indicates that sediments with a lower "1"3"7Cs concentration were transported and deposited on sediments having a higher "1"3"7Cs concentration. At the same time, the depth distribution suggests a decrease in radioactivity in provenance areas of the sediments. Analysis of the size-fractioned sediments indicated that the three sediment layers at 4–6 cm, 16–18 cm and 18–20 cm intervals had similar size distribution of "1"3"7Cs and grain size composition although the concentration levels of "1"3"7Cs were different according to their bulk concentrations. The size distribution of "1"3"7Cs also supported the possibility that the decrease in "1"3"7Cs concentration in bulk sediments above 18 cm is due to a decrease in the level of radioactivity in the catchment area. A comparison of the size distribution of "1"3"7Cs between the sediment layers above and below 18 cm suggested that the "1"3"7Cs concentration in the transported fine sediment particles decreased more with time than the "1"3"7Cs concentration in the coarse particles, reflecting the selective transport of the finer particles. The results of this study demonstrated that sediment layers deposited on a sandbar retained the cumulative history of the fluvial transport of radiocesium after the FDNPP accident. - Highlights: • We investigated the history of "1"3"7Cs recorded in sediments in the Abukuma River. • "1"3"7Cs concentration was the highest in the deepest sediment layer studied. • The depth distribution suggests a decrease in radioactivity in

  12. Morphodynamic simulation of sediment deposition patterns on a recently stripped bedrock anastomosed channel

    Directory of Open Access Journals (Sweden)

    D. Milan

    2018-04-01

    Full Text Available Some mixed bedrock-alluvial dryland rivers are known to undergo cycles of alluvial building during low flow periods, punctuated by stripping events during rare high magnitude flows. We focus on the Olifants River, Kruger National Park, South Africa, and present 2-D morphodynamic simulations of hydraulics and sediment deposition patterns over an exposed bedrock anastomosed pavement. We examine the assumptions underlying a previous conceptual model, namely that sedimentation occurs preferentially on bedrock highs. Our modelling results and local field observations in fact show that sediment thicknesses are greater over bedrock lows, suggesting these are the key loci for deposition, barform initiation and island building. During peak flows, velocities in the topographic lows tend to be lower than in intermediate topographic areas. It is likely that intermediate topographic areas supply sediment to the topographic lows at this flow stage, which is then deposited in the lows on the falling limb of the hydrograph as velocities reduce. Subsequent vegetation establishment on deposits in the topographic lows is likely to play a key role in additional sedimentation and vegetation succession, both through increasing the cohesive strength of alluvial units and by capturing new sediments and propagules.

  13. Morphodynamic simulation of sediment deposition patterns on a recently stripped bedrock anastomosed channel

    Science.gov (United States)

    Milan, David; Heritage, George; Entwistle, Neil; Tooth, Stephen

    2018-04-01

    Some mixed bedrock-alluvial dryland rivers are known to undergo cycles of alluvial building during low flow periods, punctuated by stripping events during rare high magnitude flows. We focus on the Olifants River, Kruger National Park, South Africa, and present 2-D morphodynamic simulations of hydraulics and sediment deposition patterns over an exposed bedrock anastomosed pavement. We examine the assumptions underlying a previous conceptual model, namely that sedimentation occurs preferentially on bedrock highs. Our modelling results and local field observations in fact show that sediment thicknesses are greater over bedrock lows, suggesting these are the key loci for deposition, barform initiation and island building. During peak flows, velocities in the topographic lows tend to be lower than in intermediate topographic areas. It is likely that intermediate topographic areas supply sediment to the topographic lows at this flow stage, which is then deposited in the lows on the falling limb of the hydrograph as velocities reduce. Subsequent vegetation establishment on deposits in the topographic lows is likely to play a key role in additional sedimentation and vegetation succession, both through increasing the cohesive strength of alluvial units and by capturing new sediments and propagules.

  14. Observations of Lower Mississippi River Estuarine Dynamics: Effects of the Salt Wedge on Sediment Deposition

    Science.gov (United States)

    Ramirez, M. T.; Allison, M. A.

    2017-12-01

    The lowermost Mississippi River is subject to salt-wedge estuarine conditions during seasonally low flow, when seaward flow is unable to overcome density stratification. Previous studies in the Mississippi River salt wedge have shown the deposition of a fine sediment layer accumulating several mm/day beneath the reach where the salt wedge is present. Field studies were conducted during low flow in 2012-2015 utilizing ADCP, CTD, LISST, and physical samples to observe the physics of the salt wedge reach and to calculate rates and character of sediment trapping beneath the salt wedge. The field observations were summarized using a two-layer box-model representation of the reach to calculate water and sediment budgets entering, exiting, and stored within the reach. The salt wedge reach was found to be net depositional at rates up to 1.8 mm/day. The mechanism for transferring sediment mass from the downstream-flowing fluvial layer to the upstream-flowing marine layer appears to be flocculation, evidenced in LISST data by a spike in sediment particle diameters at the halocline. Applying reach-averaged rates of sediment trapping to a time-integrated model of salt-wedge position, we calculated annual totals ranging from 0.025 to 2.2 million tons of sediment deposited beneath the salt wedge, depending on salt-wedge persistence and upstream extent. Most years this seasonal deposit is remobilized during spring flood following the low-flow estuarine season, which may affect the timing of sediment delivery to the Gulf of Mexico, as well as particulate organic carbon, whose transport trajectory mirrors that of mineral sediment. These results are also relevant to ongoing dredging efforts necessary to maintain the economically-important navigation pathway through the lower Mississippi River, as well as planned efforts to use Mississippi River sedimentary resources to build land in the degrading Louisiana deltaic coast.

  15. Sediment-hosted gold deposits of the world: database and grade and tonnage models

    Science.gov (United States)

    Berger, Vladimir I.; Mosier, Dan L.; Bliss, James D.; Moring, Barry C.

    2014-01-01

    All sediment-hosted gold deposits (as a single population) share one characteristic—they all have disseminated micron-sized invisible gold in sedimentary rocks. Sediment-hosted gold deposits are recognized in the Great Basin province of the western United States and in China along with a few recognized deposits in Indonesia, Iran, and Malaysia. Three new grade and tonnage models for sediment-hosted gold deposits are presented in this paper: (1) a general sediment-hosted gold type model, (2) a Carlin subtype model, and (3) a Chinese subtype model. These models are based on grade and tonnage data from a database compilation of 118 sediment-hosted gold deposits including a total of 123 global deposits. The new general grade and tonnage model for sediment-hosted gold deposits (n=118) has a median tonnage of 5.7 million metric tonnes (Mt) and a gold grade of 2.9 grams per tonne (g/t). This new grade and tonnage model is remarkable in that the estimated parameters of the resulting grade and tonnage distributions are comparable to the previous model of Mosier and others (1992). A notable change is in the reporting of silver in more than 10 percent of deposits; moreover, the previous model had not considered deposits in China. From this general grade and tonnage model, two significantly different subtypes of sediment-hosted gold deposits are differentiated: Carlin and Chinese. The Carlin subtype includes 88 deposits in the western United States, Indonesia, Iran, and Malaysia, with median tonnage and grade of 7.1 Mt and 2.0 g/t Au, respectively. The silver grade is 0.78 g/t Ag for the 10th percentile of deposits. The Chinese subtype represents 30 deposits in China, with a median tonnage of 3.9 Mt and medium grade of 4.6 g/t Au. Important differences are recognized in the mineralogy and alteration of the two sediment-hosted gold subtypes such as: increased sulfide minerals in the Chinese subtype and decalcification alteration dominant in the Carlin type. We therefore

  16. Evolution of radioactive dose rates in fresh sediment deposits along coastal rivers draining Fukushima contamination plume

    OpenAIRE

    Evrard, Olivier; Chartin, Caroline; Onda, Yuichi; Patin, Jeremy; Lepage, Hugo; Lef?vre, Ir?ne; Ayrault, Sophie; Ottl?, Catherine; Bont?, Philippe

    2013-01-01

    Measurement of radioactive dose rates in fine sediment that has recently deposited on channel bed-sand provides a solution to address the lack of continuous river monitoring in Fukushima Prefecture after Fukushima Dai-ichi nuclear power plant (FDNPP) accident. We show that coastal rivers of Eastern Fukushima Prefecture were rapidly supplied with sediment contaminated by radionuclides originating from inland mountain ranges, and that this contaminated material was partly exported by typhoons t...

  17. Sediment depositions upstream of open check dams: new elements from small scale models

    Science.gov (United States)

    Piton, Guillaume; Le Guern, Jules; Carbonari, Costanza; Recking, Alain

    2015-04-01

    Torrent hazard mitigation remains a big issue in mountainous regions. In steep slope streams and especially in their fan part, torrential floods mainly result from abrupt and massive sediment deposits. To curtail such phenomenon, soil conservation measures as well as torrent control works have been undertaken for decades. Since the 1950s, open check dams complete other structural and non-structural measures in watershed scale mitigation plans1. They are often built to trap sediments near the fan apexes. The development of earthmoving machinery after the WWII facilitated the dredging operations of open check dams. Hundreds of these structures have thus been built for 60 years. Their design evolved with the improving comprehension of torrential hydraulics and sediment transport; however this kind of structure has a general tendency to trap most of the sediments supplied by the headwaters. Secondary effects as channel incision downstream of the traps often followed an open check dam creation. This sediment starvation trend tends to propagate to the main valley rivers and to disrupt past geomorphic equilibriums. Taking it into account and to diminish useless dredging operation, a better selectivity of sediment trapping must be sought in open check dams, i.e. optimal open check dams would trap sediments during dangerous floods and flush them during normal small floods. An accurate description of the hydraulic and deposition processes that occur in sediment traps is needed to optimize existing structures and to design best-adjusted new structures. A literature review2 showed that if design criteria exist for the structure itself, little information is available on the dynamic of the sediment depositions upstream of open check dams, i.e. what are the geomorphic patterns that occur during the deposition?, what are the relevant friction laws and sediment transport formula that better describe massive depositions in sediment traps?, what are the range of Froude and Shields

  18. Sediment-Hosted Zinc-Lead Deposits of the World - Database and Grade and Tonnage Models

    Science.gov (United States)

    Singer, Donald A.; Berger, Vladimir I.; Moring, Barry C.

    2009-01-01

    This report provides information on sediment-hosted zinc-lead mineral deposits based on the geologic settings that are observed on regional geologic maps. The foundation of mineral-deposit models is information about known deposits. The purpose of this publication is to make this kind of information available in digital form for sediment-hosted zinc-lead deposits. Mineral-deposit models are important in exploration planning and quantitative resource assessments: Grades and tonnages among deposit types are significantly different, and many types occur in different geologic settings that can be identified from geologic maps. Mineral-deposit models are the keystone in combining the diverse geoscience information on geology, mineral occurrences, geophysics, and geochemistry used in resource assessments and mineral exploration. Too few thoroughly explored mineral deposits are available in most local areas for reliable identification of the important geoscience variables, or for robust estimation of undiscovered deposits - thus, we need mineral-deposit models. Globally based deposit models allow recognition of important features because the global models demonstrate how common different features are. Well-designed and -constructed deposit models allow geologists to know from observed geologic environments the possible mineral-deposit types that might exist, and allow economists to determine the possible economic viability of these resources in the region. Thus, mineral-deposit models play the central role in transforming geoscience information to a form useful to policy makers. This publication contains a computer file of information on sediment-hosted zinc-lead deposits from around the world. It also presents new grade and tonnage models for nine types of these deposits and a file allowing locations of all deposits to be plotted in Google Earth. The data are presented in FileMaker Pro, Excel and text files to make the information available to as many as possible. The

  19. Depositional environment of near-surface sediments, King George Basin, Bransfield Strait, Antarctica

    Science.gov (United States)

    Yoon, H. I.; Park, B. K.; Chang, S. K.; Han, M. W.; Oh, J. K.

    1994-03-01

    Four sediment cores were collected to determine the depositional environments of the King George Basin northeast of Bransfield Strait, Antarctica. The cored section revealed three distinct lithofacies: laminated siliceous ooze derived from an increased paleoproductivity near the receding sea-ice edges, massive muds that resulted from hemipelagic sedimentation in open water, and graded sediments that originated from nearby local seamounts by turbidity currents. Clay mineral data of the cores indicate a decreasing importance of volcanic activity through time. Active volcanism and hydrothermal activity appear to be responsible for the enrichment of smectite near the Penguin and Bridgeman Islands.

  20. Evaluation of soft sediment deformation structures along the Fethiye ...

    Indian Academy of Sciences (India)

    Burdur city is located on lacustrine sedimentary deposits at the northeastern end of the Fethiye–Burdur Fault Zone (FBFZ) in SW Turkey. Fault steps were formed in response to vertical displacement along normal fault zones in these deposits. Soft sediment deformation structures were identified at five sitesin lacustrine ...

  1. Spatial and temporal variability in sedimentation rates associated with cutoff channel infill deposits: Ain River, France

    Science.gov (United States)

    Piégay, H.; Hupp, C.R.; Citterio, A.; Dufour, S.; Moulin, B.; Walling, D.E.

    2008-01-01

    Floodplain development is associated with lateral accretion along stable channel geometry. Along shifting rivers, the floodplain sedimentation is more complex because of changes in channel position but also cutoff channel presence, which exhibit specific overflow patterns. In this contribution, the spatial and temporal variability of sedimentation rates in cutoff channel infill deposits is related to channel changes of a shifting gravel bed river (Ain River, France). The sedimentation rates estimated from dendrogeomorphic analysis are compared between and within 14 cutoff channel infills. Detailed analyses along a single channel infill are performed to assess changes in the sedimentation rates through time by analyzing activity profiles of the fallout radionuclides 137Cs and unsupported 210Pb. Sedimentation rates are also compared within the channel infills with rates in other plots located in the adjacent floodplain. Sedimentation rates range between 0.65 and 2.4 cm a−1 over a period of 10 to 40 years. The data provide additional information on the role of distance from the bank, overbank flow frequency, and channel geometry in controlling the sedimentation rate. Channel infills, lower than adjacent floodplains, exhibit higher sedimentation rates and convey overbank sediment farther away within the floodplain. Additionally, channel degradation, aggradation, and bank erosion, which reduce or increase the distance between the main channel and the cutoff channel aquatic zone, affect local overbank flow magnitude and frequency and therefore sedimentation rates, thereby creating a complex mosaic of sedimentation zones within the floodplain and along the cutoff channel infills. Last, the dendrogeomorphic and 137Cs approaches are cross validated for estimating the sedimentation rate within a channel infill.

  2. Ecotoxicological evaluation of sediments applied to environmental forensic investigation

    Directory of Open Access Journals (Sweden)

    R. H. Alves

    Full Text Available Abstract The present study aimed to evaluate the potential for using toxicity assays with sediment samples for the detection of water pollution caused by the discharge of tannery effluents into water bodies and its application to environmental forensic investigation. The study included ecotoxicological evaluation of sediments, survey of benthic organisms in the field, as well as chromium, cadmium and lead dosage which provided data for a sediment quality triad evaluation. The sediment samples showed acute and chronic toxicity to the bioindicators, low biodiversity of benthic macrofauna and high chromium concentration, reaching up to 4365 mg.Kg–1. A close relationship was observed between the separate results of ecotoxicological sediment evaluation and the sediment quality triad. The sediment ecotoxicological assessment proved to be applicable to tracking sources of contamination related to tanneries and similar activities in environmental forensics.

  3. Reconstructing Sediment Supply, Transport and Deposition Behind the Elwha River Dams

    Science.gov (United States)

    Beveridge, C.

    2017-12-01

    The Elwha River watershed in Olympic National Park of Washington State, USA is predominantly a steep, mountainous landscape where dominant geomorphic processes include landslides, debris flows and gullying. The river is characterized by substantial variability of channel morphology and fluvial processes, and alternates between narrow bedrock canyons and wider alluvial reaches for much of its length. Literature suggests that the Elwha watershed is topographically and tectonically in steady state. The removal of the two massive hydropower dams along the river in 2013 marked the largest dam removal in history. Over the century long lifespan of the dams, approximately 21 million cubic meters of sediment was impounded behind them. Long term erosion rates documented in this region and reservoir sedimentation data give unprecedented opportunities to test watershed sediment yield models and examine dominant processes that control sediment yield over human time scales. In this study, we aim to reconstruct sediment supply, transport and deposition behind the Glines Canyon Dam (most upstream dam) over its lifespan using a watershed modeling approach. We developed alternative models of varying complexity for sediment production and transport at the network scale driven by hydrologic forcing. We simulate sediment supply and transport in tributaries upstream of the dam. The modeled sediment supply and transport dynamics are based on calibrated formulae (e.g., bedload transport is simulated using Wilcock-Crowe 2003 with modification based on observed bedload transport in the Elwha River). Observational data that aid in our approach include DEM, channel morphology, meteorology, and streamflow and sediment (bedload and suspended load) discharge. We aim to demonstrate how the observed sediment yield behind the dams was influenced by upstream transport supply and capacity limitations, thereby demonstrating the scale effects of flow and sediment transport processes in the Elwha River

  4. Tracing contaminant pathways in sandy heterogeneous glaciofluvial sediments using a sedimentary depositional model

    International Nuclear Information System (INIS)

    Webb, E.K.; Anderson, M.P.

    1990-01-01

    Heterogeneous sedimentary deposits present complications for tracking contaminant movement by causing a complex advective flow field. Connected areas of high conductivity produce so-called fast paths that control movement of solutes. Identifying potential fast paths and describing the variation in hydraulic properties was attempted through simulating the deposition of a glaciofluvial deposit (outwash). Glaciofluvial deposits usually consist of several depositional facies, each of which has different physical characteristics, depositional structures and hydraulic properties. Therefore, it is unlikely that the property of stationarity (a constant mean hydraulic conductivity and a mono-modal probability distribution) holds for an entire glaciofluvial sequence. However, the process of dividing an outwash sequence into geologic facies presumably identifies units of material with similar physical characteristics. It is proposed that patterns of geologic facies determined by field observation can be quantified by mathematical simulation of sediment deposition. Subsequently, the simulated sediment distributions can be used to define the distribution of hydrogeologic parameters and locate possible fast paths. To test this hypothesis, a hypothetical glacial outwash deposit based on geologic facies descriptions contained in the literature was simulated using a sedimentary depositional model, SEDSIM, to produce a three-dimensional description of sediment grain size distributions. Grain size distributions were then used to estimate the spatial distribution of hydraulic conductivity. Subsequently a finite-difference flow model and linked particle tracking algorithm were used to trace conservative transport pathways. This represents a first step in describing the spatial heterogeneity of hydrogeologic characteristics for glaciofluvial and other braided stream environments. (Author) (39 refs., 7 figs.)

  5. Earthworms as colonisers: Primary colonisation of contaminated land, and sediment and soil waste deposits

    NARCIS (Netherlands)

    Eijsackers, H.J.P.

    2010-01-01

    This paper reviews the role of earthworms in the early colonisation of contaminated soils as well as sediment and waste deposits, which are worm-free because of anthropogenic activities such as open-cast mining, soil sterilisation, consistent pollution or remediation of contaminated soil. Earthworms

  6. Post-depositional formation of vivianite-type minerals alters sediment phosphorus records

    NARCIS (Netherlands)

    DIjkstra, Nikki; Hagens, Mathilde; Egger, Matthias; Slomp, Caroline P.

    2018-01-01

    Phosphorus (P) concentrations in sediments are frequently used to reconstruct past environmental conditions in freshwater and marine systems, with high values thought to be indicative of a high biological productivity. Recent studies suggest that the post-depositional formation of vivianite, an

  7. Recent sediment transport and deposition in the Nazaré Canyon, Portuguese continental margin.

    NARCIS (Netherlands)

    de Stigter, H.C.; Boer, W.; de Jesus Mendes, P.A.; Jesus, C.C.; Thomsen, L.; van den Bergh, G.D.; van Weering, T.C.E.

    2007-01-01

    Processes, pathways and fluxes of sediment transport and deposition in the Nazaré submarine canyon, Portuguese continental margin, were investigated by water column profiling of suspended particulate matter, recording of near-bottom currents and suspended particulate matter fluxes with benthic

  8. Deposition and Accumulation of Emerging Contaminants in the Sediments of the Palos Verde Shelf, California

    Science.gov (United States)

    Deposition and Accumulation of Emerging Contaminants in the Sediments of the Palos Verde Shelf, California Mark G. Cantwell, David R. Katz, Julia Sullivan, Robert P. Eganhouse, Monique M. Perron, Robert M. Burgess The Palos Verdes shelf is located off the Southern California coa...

  9. Velocity-based analysis of sediment incipient deposition in rigid boundary open channels.

    Science.gov (United States)

    Aksoy, Hafzullah; Safari, Mir Jafar Sadegh; Unal, Necati Erdem; Mohammadi, Mirali

    2017-11-01

    Drainage systems must be designed in a way to minimize undesired problems such as decrease in hydraulic capacity of the channel, blockage and transport of pollutants due to deposition of sediment. Channel design considering self-cleansing criteria are used to solve the sedimentation problem. Incipient deposition is one of the non-deposition self-cleansing design criteria that can be used as a conservative method for channel design. Experimental studies have been carried out in five different cross-section channels, namely trapezoidal, rectangular, circular, U-shape and V-bottom. Experiments were performed in a tilting flume using four different sizes of sands as sediment in nine different channel bed slopes. Two well-known methods, namely the Novak & Nalluri and Yang methods are considered for the analysis of sediment motion. Equations developed using experimental data are found to be in agreement with the literature. It is concluded that the design velocity depends on the shape of the channel cross-section. Rectangular and V-bottom channels need lower and higher incipient deposition velocities, respectively, in comparison with other channels.

  10. Plutonium transport to and deposition and immobility in Irish Sea intertidal sediments

    Energy Technology Data Exchange (ETDEWEB)

    Aston, S R; Stanners, D A [Lancaster Univ. (UK)

    1981-02-12

    The results are presented of an investigation of plutonium in intertidal sediments of the Irish Sea, contaminated with radioactive wastes from the Windscale reprocessing facility. The deposition characteristics and lack of vertical migration of /sup 238/Pu and /sup 239/ and /sup 240/Pu are discussed.

  11. The effect of deposited fine sediment on summer survival and growth of rainbow trout in riffles of a small stream

    Science.gov (United States)

    Bret C. Harvey; Jason L. White; Rodney J. Nakamoto

    2009-01-01

    Elevated fine-sediment inputs to streams can alter a variety of conditions and processes, including the amount of fine sediment stored in riffles. We sought to measure the influence of deposited fine sediment on the survival and growth of juvenile rainbow trout Oncorhynchus mykiss (106–130 mm fork length) using a field experiment that included 18 enclosures in riffles...

  12. Estuarine Sediment Deposition during Wetland Restoration: A GIS and Remote Sensing Modeling Approach

    Science.gov (United States)

    Newcomer, Michelle; Kuss, Amber; Kentron, Tyler; Remar, Alex; Choksi, Vivek; Skiles, J. W.

    2011-01-01

    Restoration of the industrial salt flats in the San Francisco Bay, California is an ongoing wetland rehabilitation project. Remote sensing maps of suspended sediment concentration, and other GIS predictor variables were used to model sediment deposition within these recently restored ponds. Suspended sediment concentrations were calibrated to reflectance values from Landsat TM 5 and ASTER using three statistical techniques -- linear regression, multivariate regression, and an Artificial Neural Network (ANN), to map suspended sediment concentrations. Multivariate and ANN regressions using ASTER proved to be the most accurate methods, yielding r2 values of 0.88 and 0.87, respectively. Predictor variables such as sediment grain size and tidal frequency were used in the Marsh Sedimentation (MARSED) model for predicting deposition rates for three years. MARSED results for a fully restored pond show a root mean square deviation (RMSD) of 66.8 mm (<1) between modeled and field observations. This model was further applied to a pond breached in November 2010 and indicated that the recently breached pond will reach equilibrium levels after 60 months of tidal inundation.

  13. Evaluation of droplet deposition in rod bundle

    International Nuclear Information System (INIS)

    Ji, W.; Gu, C.Y.; Anglart, H.

    1997-01-01

    Deposition model for droplets in gas droplet two-phase flow in rod bundle is developed in this work using the Lagrangian method. The model is evaluated in a 9-rod bundle geometry. The deposition coefficient in the bundle geometry are compared with that in round tube. The influences of the droplet size and gas mass flow rate on deposition coefficient are investigated. Furthermore, the droplet motion is studied in more detail by dividing the bundle channel into sub-channels. The results show that the overall deposition coefficient in the bundle geometry is close to that in the round tube with the diameter equal to the bundle hydraulic diameter. The calculated deposition coefficient is found to be higher for higher gas mass flux and smaller droplets. The study in the sub-channels show that the ratio between the local deposition coefficient for a sub-channel and the averaged value for the whole bundle is close to a constant value, deviations from the mean value for all the calculated cases being within the range of ±13%. (author)

  14. Geochemical partitioning of lead in biogenic carbonate sediments in a coral reef depositional environment

    International Nuclear Information System (INIS)

    Horta-Puga, Guillermo

    2017-01-01

    The fate of trace elements in reef depositional environments has not been extensively investigated. The aim of this study was to determine the partitioning of Pb in sediments of the Veracruz Reef System, and its relation to local environmental sources. Lead was determined in four geochemical fractions: exchangeable (3.8 ± 0.4 μg g −1 ), carbonate (57.0 ± 13.6 μg g −1 ), organic matter (2.0 ± 0.9 μg g −1 ), and mineral (17.5 ± 5.4 μg g −1 ). For the mineral fraction, lead concentrations were higher in those reefs influenced by river discharge or by long-distance transport of terrigenous sediments. The bioavailable concentration of lead (range: 21.9–85.6 μg g −1 ) indicates that the Veracruz Reef System is a moderately polluted area. As expected, the carbonate fraction contained the highest proportion of Pb (70%), and because the reef framework is largely made up of by biogenic carbonate sediments, hence, it is therefore the most important repository of Pb in coral reef depositional environments. - Highlights: • Lead concentrations were determined in four geochemical fractions of reef sediments. • The carbonate fraction accounted for > 70% of the content of Pb in reef sediments. • Terrigenous sediments are the main source of Pb associated to the mineral fraction. • The Veracruz Reef System is considered a moderately polluted area. • Sediments are the main repositories of lead in coral reef depositional environments.

  15. Evolution of radioactive dose rates in fresh sediment deposits along coastal rivers draining Fukushima contamination plume.

    Science.gov (United States)

    Evrard, Olivier; Chartin, Caroline; Onda, Yuichi; Patin, Jeremy; Lepage, Hugo; Lefèvre, Irène; Ayrault, Sophie; Ottlé, Catherine; Bonté, Philippe

    2013-10-29

    Measurement of radioactive dose rates in fine sediment that has recently deposited on channel bed-sand provides a solution to address the lack of continuous river monitoring in Fukushima Prefecture after Fukushima Dai-ichi nuclear power plant (FDNPP) accident. We show that coastal rivers of Eastern Fukushima Prefecture were rapidly supplied with sediment contaminated by radionuclides originating from inland mountain ranges, and that this contaminated material was partly exported by typhoons to the coastal plains as soon as by November 2011. This export was amplified during snowmelt and typhoons in 2012. In 2013, contamination levels measured in sediment found in the upper parts of the catchments were almost systematically lower than the ones measured in nearby soils, whereas their contamination was higher in the coastal plains. We thereby suggest that storage of contaminated sediment in reservoirs and in coastal sections of the river channels now represents the most crucial issue.

  16. Panel 1 - comparative evaluation of deposition technologies

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, G.R.; Stodolsky, F. [Argonne National Lab., IL (United States); Benson, D.K.; Pitts, R.J. [National Renewable Energy Lab., Golden, CO (United States); Bhat, D.G. [GTE Valenite Corp., Troy, MI (United States); Yulin Chen [Allison Gas Turbine Division, GM, Indianapolis, IN (United States); Gat, R.; Sunkara, M.K. [Case Western Reserve Univ., Cleveland, OH (United States); Kelly, M. [Stanford Univ., CA (United States); Lawler, J.E. [Univ. of Wisconsin, Madison (United States); Nagle, D.C. [Martin Marietta Labs., Baltimore, MD (United States); Outka, D. [Sandia National Laboratories, Livermore, CA (United States); Revankar, G.S. [Deere & Co., Moline, IL (United States); Subramaniam, V.V. [Ohio State Univ., Columbus (United States); Wilbur, P.J. [Colorado State Univ., Fort Collins (United States); Mingshow Wong [Northwestern Univ., Evanston, IL (United States); Woolam, W.E. [Southwest Research Inst., Arlington, VA (United States)

    1993-01-01

    This working group attempted to evaluate/compare the different types of deposition techniques currently under investigation for depositing diamond and diamond-like carbon films. A table lists the broad types of techniques that were considered for depositing diamond and diamond-like carbon films. After some discussion, it was agreed that any evaluation of the various techniques would be dependent on the end application. Thus the next action was to list the different areas where diamond and DLC films could find applications in transportation. These application areas are listed in a table. The table intentionally does not go into great detail on applications because that subject is dealt with specifically by Panel No. 4 - Applications To Transportation. The next action concentrated on identifying critical issues or limitations that need to be considered in evaluating the different processes. An attempt was then made to rank different broad categories of deposition techniques currently available or under development based on the four application areas and the limitations. These rankings/evaluations are given for diamond and DLC techniques. Finally, the working group tried to identify critical development and research issues that need to be incorporated into developing a long-term program that focuses on diamond/DLC coatings for transportation needs. 5 tabs.

  17. Post-depositional formation of vivianite-type minerals alters sediment phosphorus records

    Directory of Open Access Journals (Sweden)

    N. Dijkstra

    2018-02-01

    Full Text Available Phosphorus (P concentrations in sediments are frequently used to reconstruct past environmental conditions in freshwater and marine systems, with high values thought to be indicative of a high biological productivity. Recent studies suggest that the post-depositional formation of vivianite, an iron(II-phosphate mineral, might significantly alter trends in P with sediment depth. To assess its importance, we investigate a sediment record from the Bornholm Basin that was retrieved during the Integrated Ocean Drilling Program (IODP Baltic Sea Paleoenvironment Expedition 347 in 2013, consisting of lake sediments overlain by brackish–marine deposits. Combining bulk sediment geochemistry with microanalysis using scanning electron microscope energy dispersive spectroscopy (SEM-EDS and synchrotron-based X-ray absorption spectroscopy (XAS, we demonstrate that vivianite-type minerals rich in manganese and magnesium are present in the lake deposits just below the transition to the brackish–marine sediments (at 11.5 to 12 m sediment depth. In this depth interval, phosphate that diffuses down from the organic-rich, brackish–marine sediments meets porewaters rich in dissolved iron in the lake sediments, resulting in the precipitation of iron(II phosphate. Results from a reactive transport model suggest that the peak in iron(II phosphate originally occurred at the lake–marine transition (9 to 10 m and moved downwards due to changes in the depth of a sulfidization front. However, its current position relative to the lake–marine transition is stable as the vivianite-type minerals and active sulfidization fronts have been spatially separated over time. Experiments in which vivianite was subjected to sulfidic conditions demonstrate that incorporation of manganese or magnesium in vivianite does not affect its susceptibility to sulfide-induced dissolution. Our work highlights that post-depositional formation of iron(II phosphates such as vivianite has

  18. Post-depositional formation of vivianite-type minerals alters sediment phosphorus records

    Science.gov (United States)

    Dijkstra, Nikki; Hagens, Mathilde; Egger, Matthias; Slomp, Caroline P.

    2018-02-01

    Phosphorus (P) concentrations in sediments are frequently used to reconstruct past environmental conditions in freshwater and marine systems, with high values thought to be indicative of a high biological productivity. Recent studies suggest that the post-depositional formation of vivianite, an iron(II)-phosphate mineral, might significantly alter trends in P with sediment depth. To assess its importance, we investigate a sediment record from the Bornholm Basin that was retrieved during the Integrated Ocean Drilling Program (IODP) Baltic Sea Paleoenvironment Expedition 347 in 2013, consisting of lake sediments overlain by brackish-marine deposits. Combining bulk sediment geochemistry with microanalysis using scanning electron microscope energy dispersive spectroscopy (SEM-EDS) and synchrotron-based X-ray absorption spectroscopy (XAS), we demonstrate that vivianite-type minerals rich in manganese and magnesium are present in the lake deposits just below the transition to the brackish-marine sediments (at 11.5 to 12 m sediment depth). In this depth interval, phosphate that diffuses down from the organic-rich, brackish-marine sediments meets porewaters rich in dissolved iron in the lake sediments, resulting in the precipitation of iron(II) phosphate. Results from a reactive transport model suggest that the peak in iron(II) phosphate originally occurred at the lake-marine transition (9 to 10 m) and moved downwards due to changes in the depth of a sulfidization front. However, its current position relative to the lake-marine transition is stable as the vivianite-type minerals and active sulfidization fronts have been spatially separated over time. Experiments in which vivianite was subjected to sulfidic conditions demonstrate that incorporation of manganese or magnesium in vivianite does not affect its susceptibility to sulfide-induced dissolution. Our work highlights that post-depositional formation of iron(II) phosphates such as vivianite has the potential to strongly

  19. Sediment deposition and sources into a Mississippi River floodplain lake; Catahoula Lake, Louisiana

    Science.gov (United States)

    Latuso, Karen D.; Keim, Richard F.; King, Sammy L.; Weindorf, David C.; DeLaune, Ronald D.

    2017-01-01

    Floodplain lakes are important wetlands on many lowland floodplains of the world but depressional floodplain lakes are rare in the Mississippi River Alluvial Valley. One of the largest is Catahoula Lake, which has existed with seasonally fluctuating water levels for several thousand years but is now in an increasingly hydrologically altered floodplain. Woody vegetation has been encroaching into the lake bed and the rate of this expansion has increased since major human hydrologic modifications, such as channelization, levee construction, and dredging for improvement of navigation, but it remains unknown what role those modifications may have played in altering lake sedimentation processes. Profiles of thirteen 137Cs sediment cores indicate sedimentation has been about 0.26 cm y− 1 over the past 60 years and has been near this rate since land use changes began about 200 years ago (210Pb, and 14C in Tedford, 2009). Carbon sequestration was low (10.4 g m− 2 y− 1), likely because annual drying promotes mineralization and export. Elemental composition (high Zr and Ti and low Ca and K) and low pH of recent (sediments suggest Gulf Coastal Plain origin, but below the recent sediment deposits, 51% of sediment profiles showed influence of Mississippi River alluvium, rich in base cations such as K+, Ca2 +, and Mg2 +. The recent shift to dominance of Coastal Plain sediments on the lake-bed surface suggests hydrologic modification has disconnected the lake from sediment-bearing flows from the Mississippi River. Compared to its condition prior to hydrologic alterations that intensified in the 1930s, Catahoula Lake is about 15 cm shallower and surficial sediments are more acidic. Although these results are not sufficient to attribute ecological changes directly to sedimentological changes, it is likely the altered sedimentary and hydrologic environment is contributing to the increased dominance of woody vegetation.

  20. Arctic deltaic lake sediments as recorders of fluvial organic matter deposition

    Directory of Open Access Journals (Sweden)

    Jorien E Vonk

    2016-08-01

    Full Text Available Arctic deltas are dynamic and vulnerable regions that play a key role in land-ocean interactions and the global carbon cycle. Delta lakes may provide valuable historical records of the quality and quantity of fluvial fluxes, parameters that are challenging to investigate in these remote regions. Here we study lakes from across the Mackenzie Delta, Arctic Canada, that receive fluvial sediments from the Mackenzie River when spring flood water levels rise above natural levees. We compare downcore lake sediments with suspended sediments collected during the spring flood, using bulk (% organic carbon, % total nitrogen, 13C, 14C and molecular organic geochemistry (lignin, leaf waxes. High-resolution age models (137Cs, 210Pb of downcore lake sediment records (n=11 along with lamina counting on high-resolution radiographs show sediment deposition frequencies ranging between annually to every 15 years. Down-core geochemical variability in a representative delta lake sediment core is consistent with historical variability in spring flood hydrology (variability in peak discharge, ice jamming, peak water levels. Comparison with earlier published Mackenzie River depth profiles shows that (i lake sediments reflect the riverine surface suspended load, and (ii hydrodynamic sorting patterns related to spring flood characteristics are reflected in the lake sediments. Bulk and molecular geochemistry of suspended particulate matter from the spring flood peak and lake sediments are relatively similar showing a mixture of modern higher-plant derived material, older terrestrial permafrost material, and old rock-derived material. This suggests that deltaic lake sedimentary records hold great promise as recorders of past (century-scale riverine fluxes and may prove instrumental in shedding light on past behaviour of arctic rivers, as well as how they respond to a changing climate.

  1. Sediment spatial distribution evaluated by three methods and its relation to some soil properties

    Energy Technology Data Exchange (ETDEWEB)

    Bacchi, O O.S. . [Centro de Energia Nuclear na Agricultura-CENA/USP, Laboratorio de Fisica do Solo, Piracicaba, SP (Brazil); Reichardt, K [Centro de Energia Nuclear na Agricultura-CENA/USP, Laboratorio de Fisica do Solo, Piracicaba, SP (Brazil); Departamento de Ciencias Exatas, Escola Superior de Agricultura ' Luiz de Queiroz' ESALQ/USP, Piracicaba, SP (Brazil); Sparovek, G [Departamento de Solos e Nutricao de Plantas, Escola Superior de Agricultura ' Luiz de Queiroz' ESALQ/USP, Piracicaba, SP (Brazil)

    2003-02-15

    An investigation of rates and spatial distribution of sediments on an agricultural field cultivated with sugarcane was undertaken using the {sup 137}Cs technique, USLE and WEPP models. The study was carried out on the Ceveiro watershed of the Piracicaba river basin, state of Sao Paulo, Brazil, experiencing severe soil degradation due to soil erosion. The objectives of the study were to compare the spatial distribution of sediments evaluated by the three methods and its relation to some soil properties. Erosion and sedimentation rates and their spatial distribution estimated by the three methods were completely different. Although not able to show sediment deposition, the spatial distribution of erosion rates evaluated by USLE presented the best correlation with other studied soil properties. (author)

  2. 3D Numerical Modelling of Transport, Deposition and Resuspension of Highway Deposited Sediments in Wet Detention Ponds

    DEFF Research Database (Denmark)

    Bentzen, Thomas Ruby

    2009-01-01

    concrete channel with width of 0.8 m and a water depth of approximately 0.8 m and in circular flume experiments in order to reproduce near-bed specific processes such as resuspension and consolidation. With good agreement with measurements, modelling of hydrodynamics, transport of dissolved pollutants...... and particles in wet detention ponds is possible with application of a three dimensional RANS model and the advection/dispersion equation taken physical phenomena like wind, waves, deposition, erosion and consolidation of the bottom sediment into account....

  3. Evaluating Sediment Mobility for Siting Nearshore Berms

    Science.gov (United States)

    2016-04-01

    placement of dredged sediment that may contain more fine silts and clays than are allowed for placement directly on the beach. The United States Army...used in the density and viscosity calculations. For this technical note an example study site is selected and the sediment mobility indexes are...acceleration due to gravity, sρ is the sediment density, ρ is the water density, v is the kinematic viscosity of water, crθ is the Shields

  4. Transport and deposition of plutonium-contaminated sediments by fluvial processes, Los Alamos Canyon, New Mexico

    International Nuclear Information System (INIS)

    Graf, W.L.

    1996-01-01

    Between 1945 and 1952 the development of nuclear weapons at Los Alamos National Laboratory, New Mexico, resulted in the disposal of plutonium into the alluvium of nearby Acid and (to a lesser degree) DP Canyons. The purpose of this paper is to explore the connection between the disposal sites and the main river, a 20 km link formed by the fluvial system of Acid, Pueblo, DP, and Los Alamos Canyons. Empirical data from 15 yr of annual sediment sampling throughout the canyon system has produced 458 observations of plutonium concentration in fluvial sediments. These data show that, overall, mean plutonium concentrations in fluvial sediment decline from 10,000 fCi/g near the disposal area to 100 fCi/g at the confluence of the canyon system and the Rio Grande. Simulations using a computer model for water, sediment, and plutonium routing in the canyon system show that discharges as large as the 25 yr event would fail to develop enough transport capacity to completely remove the contaminated sediments from Pueblo Canyon. Lesser flows would move some materials to the Rio Grande by remobilization of stored sediments. The simulations also show that the deposits and their contaminants have a predictable geography because they occur where stream power is low, hydraulic resistance is high, and the geologic and/or geomorphic conditions provide enough space for storage. 38 refs., 13 figs., 1 tab

  5. Geometrical Characterization of Sediment Deposits at the Confluence of Mountain Streams

    Directory of Open Access Journals (Sweden)

    Laura Maria Stancanelli

    2018-03-01

    Full Text Available Debris flow injections from tributaries into a main mountain stream generate deposits of sediments which, in turn, result in obstruction and eventual damming of the river section. This contribution presents the results of a series of flume experiments on the dynamics of these deposits, with reference to three different types of blockage: no blockage, partial blockage, and full blockage. Results show that the shape of the deposit is mainly controlled by the ratio between the debris flow discharge and the main river discharge. The experimental dataset is used to develop a deposit resilience stability index based on the shape of the deposit contour retrieved from photos taken from above. The proposed index is based on the invariant elliptic Fourier coefficients and the dimensionless transverse obstruction parameter. The elliptic Fourier coefficients give information on the symmetry of the deposit contour. High symmetry indicates more stable and resilient deposits. The proposed index is calibrated on the basis of the flume experiments and tested with field data. The results are quite promising and suggest that the index can be appropriate for a fast hazard assessment of multiple debris flow deposits at a regional scale.

  6. Deposition of plutonium isotopes and Cs-137 in sediments of the Ob delta from the beginning of the nuclear age

    International Nuclear Information System (INIS)

    Panteleyev, G.P.; Livingston, H.D.; Sayles, F.L.; Medkova, O.N.

    1995-01-01

    As an approach to an assessment of the transport of artificial radionuclides through the Ob river system towards the arctic Ocean, results are presented from the analyses of a series of sediment cores collected in the Ob delta and estuary in 1994. These cores, collected in areas of sediment accumulation, contain the depositional history at the Ob mouth of substances associated with sediment particles from the whole river system watershed. Several approaches to dating these sediments permitted the development of a chronology for the deposition of plutonium isotopes and Cs-137, following their first introduction to the environment a half century ago. Some preliminary results for I-129 are also presented. 6 figs

  7. Comparative analyses of the bacterial community of hydrothermal deposits and seafloor sediments across Okinawa Trough

    Science.gov (United States)

    Wang, Long; Yu, Min; Liu, Yan; Liu, Jiwen; Wu, Yonghua; Li, Li; Liu, Jihua; Wang, Min; Zhang, Xiao-Hua

    2018-04-01

    As an ideal place to study back-arc basins and hydrothermal eco-system, Okinawa Trough has attracted the interests of scientists for decades. However, there are still no in-depth studies targeting the bacterial community of the seafloor sediments and hydrothermal deposits in Okinawa Trough. In the present study, we reported the bacterial community of the surface deposits of a newly found hydrothermal field in the southern Okinawa Trough, and the horizontal and vertical variation of bacterial communities in the sediments of the northern Okinawa Trough. The hydrothermal deposits had a relatively high 16S rRNA gene abundance but low bacterial richness and diversity. Epsilonproteobacteria and Bacteroidetes were predominant in hydrothermal deposits whereas Deltaproteobacteria, Gammaproteobacteria and Chloroflexi were abundant across all samples. The bacterial distribution in the seafloor of Okinawa Trough was significantly correlated to the content of total nitrogen, and had consistent relationship with total carbon. Gradual changes of sulfur-oxidizing bacteria were found with the distance away from hydrothermal fields, while the hydrothermal activity did not influence the distribution of the major clades of sulfate-reducing bacteria. Higher abundance of the sulfur cycle related genes (aprA and dsrB), and lower abundance of the bacterial ammonia-oxidizing related gene (amoA) were quantified in hydrothermal deposits. In addition, the present study also compared the inter-field variation of Epsilonproteobacteria among multi-types of hydrothermal vents, revealing that the proportion and diversity of this clade were quite various.

  8. Sediment transport and deposition on a river-dominated tidal flat: An idealized model study

    Science.gov (United States)

    Sherwood, Christopher R.; Chen, Shih-Nan; Geyer, W. Rockwell; Ralston, David K.

    2010-01-01

    A 3-D hydrodynamic model is used to investigate how different size classes of river-derived sediment are transported, exported and trapped on an idealized, river-dominated tidal flat. The model is composed of a river channel flanked by sloping tidal flats, a configuration motivated by the intertidal region of the Skagit River mouth in Washington State, United States. It is forced by mixed tides and a pulse of freshwater and sediment with various settling velocities. In this system, the river not only influences stratification but also contributes a significant cross-shore transport. As a result, the bottom stress is strongly ebb-dominated in the channel because of the seaward advance of strong river flow as the tidal flats drain during ebbs. Sediment deposition patterns and mass budgets are sensitive to settling velocity. The lateral sediment spreading scales with an advective distance (settling time multiplied by lateral flow speed), thereby confining the fast settling sediment classes in the channel. Residual sediment transport is landward on the flats, because of settling lag, but is strongly seaward in the channel. The seaward transport mainly occurs during big ebbs and is controlled by a length scale ratio Ld/XWL, where Ld is a cross-shore advective distance (settling time multiplied by river outlet velocity), and XWL is the immersed cross-shore length of the intertidal zone. Sediment trapping requires Ld/XWL stratification and reducing tidal range both favor sediment trapping, whereas varying channel geometries and asymmetry of tides has relatively small impacts. Implications of the modeling results on the south Skagit intertidal region are discussed.

  9. Hydraulic experiment on formation mechanism of tsunami deposit and verification of sediment transport model for tsunamis

    Science.gov (United States)

    Yamamoto, A.; Takahashi, T.; Harada, K.; Sakuraba, M.; Nojima, K.

    2017-12-01

    An underestimation of the 2011 Tohoku tsunami caused serious damage in coastal area. Reconsideration for tsunami estimation needs knowledge of paleo tsunamis. The historical records of giant tsunamis are limited, because they had occurred infrequently. Tsunami deposits may include many of tsunami records and are expected to analyze paleo tsunamis. However, present research on tsunami deposits are not able to estimate the tsunami source and its magnitude. Furthermore, numerical models of tsunami and its sediment transport are also important. Takahashi et al. (1999) proposed a model of movable bed condition due to tsunamis, although it has some issues. Improvement of the model needs basic data on sediment transport and deposition. This study investigated the formation mechanism of tsunami deposit by hydraulic experiment using a two-dimensional water channel with slope. In a fixed bed condition experiment, velocity, water level and suspended load concentration were measured at many points. In a movable bed condition, effects of sand grains and bore wave on the deposit were examined. Yamamoto et al. (2016) showed deposition range varied with sand grain sizes. In addition, it is revealed that the range fluctuated by number of waves and wave period. The measurements of velocity and water level showed that flow was clearly different near shoreline and in run-up area. Large velocity by return flow was affected the amount of sand deposit near shoreline. When a cutoff wall was installed on the slope, the amount of sand deposit repeatedly increased and decreased. Especially, sand deposit increased where velocity decreased. Takahashi et al. (1999) adapted the proposed model into Kesennuma bay when the 1960 Chilean tsunami arrived, although the amount of sand transportation was underestimated. The cause of the underestimation is inferred that the velocity of this model was underestimated. A relationship between velocity and sediment transport has to be studied in detail, but

  10. Radionuclides deposition and fine sediment transport in a forested watershed, central Japan

    Science.gov (United States)

    Nam, S.; Gomi, T.; Kato, H.; Tesfaye, T.; Onda, Y.

    2011-12-01

    We investigated radionuclides deposition and fine sediment transport in a 13 ha headwater watershed, Tochigi prefecture, located in 98.94 km north of Tokyo. The study site was within Karasawa experimental forest, Tokyo University of Agriculture and Technology. We conducted fingerprinting approach, based on the activities of fallout radionuclides, including caesium-134 (Cs-134) caesium-137 (Cs-137) and excess lead-210 (Pb-210ex). For indentifying specific sources of fine sediment, we sampled tree, soil on forested floor, soil on logging road surface, stream bed and stream banks. We investigated the radionuclides (i.e., as Cs-134, Cs-137 and Pb-210ex) deposition on tree after accident of nuclear power plants on March 11, 2011. We sampled fruits, leaves, branches, stems, barks on Japanese cedar (Sugi) and Japanese cypress (Hinoki). To analyze the samples, gammaray spectrometry was performed at a laboratory at the University of Tsukuba (Tsukuba City, Japan) using n-type coaxial low-energy HPGe gamma detectors (EGC-200-R and EGC25-195-R of EURYSIS Co., Lingolsheim, France) coupled with a multichannel analyzer. We also collected soil samples under the forest canopy in various soil depths from 2, 5, 10, 20, 30 cm along transect of hillslopes. Samples at forest road were collected road segments crossing on the middle section of monitoring watersheds. Fine sediment transport in the streams were collected at the outlet of 13 ha watersheds using integrated suspended sediment samplers. This study indicates the some portion of radio nuclide potentially remained on the tree surface. Part of the deposited radionuclides attached to soil particles and transported to the streams. Most of the fine sediment can be transported on road surface and/or near stream side (riparian zones).

  11. Physicochemical and biological characterisation of different dredged sediment deposit sites in France

    International Nuclear Information System (INIS)

    Capilla, Xavier; Schwartz, Christophe; Bedell, Jean-Philippe; Sterckeman, Thibault; Perrodin, Yves; Morel, Jean-Louis

    2006-01-01

    The aim of this work is to determine sediment properties, metal contents and transfers of Cd and Zn from dredged sediments to plants. To this end 10 deposit sites with different contexts were visited in France. The main agronomic characteristics and metal contents for surface soil layers were measured, the plant species present at the sites, such as Brassicaceae and Fabaceae, were listed, and the distribution of their root systems described. Soil characteristics such as available P (Olsen) varied between sites, with values ranging from 0.01 to 0.49 g kg -1 . Total contents and enrichment factors were studied, highlighting metal contamination in most of the sites. Despite carrying out principal component analyses, it was not possible to group deposits by age or geographical localisation. However, deposits could be distinguished as a function of proximity of industrial facilities, sediment grain size and carbonate content. Associations between metals were also highlighted: (1) Cd, Pb and Zn, and (2) Al, Cr, Cu and Fe. Consequently, we propose classifying them as technogenic anthrosols. - The term technogenic arthrosols is suggested

  12. Physicochemical and biological characterisation of different dredged sediment deposit sites in France

    Energy Technology Data Exchange (ETDEWEB)

    Capilla, Xavier [Laboratoire des Sciences de l' Environnement a l' ENTPE, Rue Maurice Audin, 69 518 Vaulx-en-Velin Cedex (France); Schwartz, Christophe [Laboratoire Sols et Environnement, INPL (ENSAIA)/INRA UMR 1120, 2 avenue de la foret de Haye, BP 172, 54 505 Vandoeuvre les Nancy (France); Bedell, Jean-Philippe [Laboratoire des Sciences de l' Environnement a l' ENTPE, Rue Maurice Audin, 69 518 Vaulx-en-Velin Cedex (France)]. E-mail: bedell@entpe.fr; Sterckeman, Thibault [Laboratoire Sols et Environnement, INPL (ENSAIA)/INRA UMR 1120, 2 avenue de la foret de Haye, BP 172, 54 505 Vandoeuvre les Nancy (France); Perrodin, Yves [Laboratoire des Sciences de l' Environnement a l' ENTPE, Rue Maurice Audin, 69 518 Vaulx-en-Velin Cedex (France); Morel, Jean-Louis [Laboratoire Sols et Environnement, INPL (ENSAIA)/INRA UMR 1120, 2 avenue de la foret de Haye, BP 172, 54 505 Vandoeuvre les Nancy (France)

    2006-09-15

    The aim of this work is to determine sediment properties, metal contents and transfers of Cd and Zn from dredged sediments to plants. To this end 10 deposit sites with different contexts were visited in France. The main agronomic characteristics and metal contents for surface soil layers were measured, the plant species present at the sites, such as Brassicaceae and Fabaceae, were listed, and the distribution of their root systems described. Soil characteristics such as available P (Olsen) varied between sites, with values ranging from 0.01 to 0.49 g kg{sup -1}. Total contents and enrichment factors were studied, highlighting metal contamination in most of the sites. Despite carrying out principal component analyses, it was not possible to group deposits by age or geographical localisation. However, deposits could be distinguished as a function of proximity of industrial facilities, sediment grain size and carbonate content. Associations between metals were also highlighted: (1) Cd, Pb and Zn, and (2) Al, Cr, Cu and Fe. Consequently, we propose classifying them as technogenic anthrosols. - The term technogenic arthrosols is suggested.

  13. Effects of storm waves on rapid deposition of sediment in the Yangtze Estuary channel

    Directory of Open Access Journals (Sweden)

    Xu Fumin

    2008-03-01

    Full Text Available Recent research on short-term topographic change in the Yangtze Estuary channel under storm surge conditions is briefly summarized. The mild-slope, Boussinesq and action balance equations are compared and analyzed. The action balance equation, SWAN, was used as a wave numerical model to forecast strong storm waves in the Yangtze Estuary. The spherical coordinate system and source terms used in the equation are described in this paper. The significant wave height and the wave orbital motion velocity near the bottom of the channel during 20 m/s winds in the EES direction were simulated, and the model was calibrated with observation data of winds and waves generated by Tropical Cyclone 9912. The distribution of critical velocity for incipient motion along the bottom was computed according to the threshold velocity formula for bottom sediment. The mechanism of rapid deposition is analyzed based on the difference between the root-mean-square value of the near-bottom wave orbital motion velocity and the bottom critical tractive velocity. The results show that a large amount of bottom sediments from Hengsha Shoal and Jiuduan Shoal are lifted into the water body when 20 m/s wind is blowing in the EES direction. Some of the sediments may enter the channel with the cross-channel current, causing serious rapid deposition. Finally, the tendency of the storm to induce rapid deposition in the Yangtze Estuary channel zone is analyzed.

  14. Functional evaluation of pollutant transformation in sediment from combined sewer system.

    Science.gov (United States)

    Shi, Xuan; Ngo, Huu Hao; Sang, Langtao; Jin, Pengkang; Wang, Xiaochang C; Wang, Guanghua

    2018-07-01

    In this study, a pilot combined sewer system was constructed to characterize the pollutant transformation in sewer sediment. The results showed that particulate contaminants deposited from sewage could be transformed into dissolved matter by distinct pollutant transformation pathways. Although the oxidation-reduction potential (ORP) was varied from -80 mV to -340 mV in different region of the sediment, the fermentation was the dominant process in all regions of the sediment, which induced hydrolysis and decomposition of particulate contaminants. As a result, the accumulation of dissolved organic matter and the variation of ORP values along the sediment depth led to the depth-dependent reproduction characteristics of methanogens and sulfate-reducing bacteria, which were existed in the middle and deep layer of the sediment respectively. However, the diversity of nitrifying and polyphosphate-accumulating bacteria was low in sewer sediment and those microbial communities showed a non-significant correlation with nitrogen and phosphorus contaminants, which indicated that the enrichment of nitrogen and phosphorus contaminants was mainly caused by physical deposition process. Thus, this study proposed a promising pathway to evaluate pollutant transformation and can help provide theoretical foundation for urban sewer improvement. Copyright © 2018 Elsevier Ltd. All rights reserved.

  15. Sediment quality in depositional areas of Shelikof Strait and outermost Cook Inlet, July 1997 - July 1998 (NODC Accession 0000702)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Minerals Management Service (MMS) program "Sediment Quality in Depositional Areas of Shelikof Strait and Outermost Cook Inlet," consisted of a two-year study...

  16. Lithology, monsoon and sea-surface current control on provenance, dispersal and deposition of sediments over the Andaman continental shelf

    Digital Repository Service at National Institute of Oceanography (India)

    Damodararao, K.; Singh, S.K.; Rai, V.K.; Ramaswamy, V.; Rao, P.S.

    , constrain their transport pathways and assess the factors influencing the erosion in the catchment and their dispersal and deposition over the Andaman Shelf region. Major elemental compositions of the shelf sediments suggest mafic lithology...

  17. Phorbin steryl esters in Black Sea sediment traps and sediments: A preliminary evaluation of their paleooceanographic potential

    Science.gov (United States)

    King, Linda L.; Repeta, Daniel J.

    1994-10-01

    The distributions of pyropheophorbide- a steryl esters in one-year deployments of sediment traps at two locations in the Black Sea are described. In nearly all our trap samples, phorbin steryl esters (PSEs) contribute a significant portion of the total phorbin flux. The relative abundances of sterols esterified to pyropheophorbide- a varied throughout the year, and we suggest these changes result from the observed seasonal variation of phytoplankton species in the overlying water column. The distribution of free sterols in a one-year composite sediment trap sample closely approximates the distribution of sterols derived from the hydrolysis of sedimentary PSEs collected at an adjacent site. From these results, we suggest that the distribution of sedimentary PSE sterols provides a record of sterol deposition to the sediment-water interface. Esterification of sterols to pyropheophorbide- a apparently prevents the preferential removal of 4-desmethyl sterols relative to 4-methyl sterols, and the reduction of stenols to stanols during degradation. Analysis of PSEs in a gravity core covering the last 8-10 Kyr shows that the abundance and distribution of PSEs change with downcore variations in sedimentology. Detailed analysis of PSEs in sediments may, therefore, provide a means to evaluate paleooceanographic changes in phytoplankton community structure and sterol early diagenesis. The synthesis, NMR, CI-MS, and visible spectroscopic properties of four abundant PSEs found in the Black Sea are also described.

  18. Evaluation of the toxicity of organic matter in marine sediments

    Digital Repository Service at National Institute of Oceanography (India)

    Sarkar, A.

    The inhibitory effects of the organics from the sediment along the east coast of India on acetylcholinesterase (AChE) in-vitro were evaluated. Sediment samples collected from the surface layers at various depths were extracted. Each of the extracts...

  19. Characteristics of uranium mineralization and depositional system of host sediments, Bayantala basin, Inner Mongolia autonomous region

    International Nuclear Information System (INIS)

    Zhu Minqiang; Wu Rengui; Yu Dagan; Chen Anping; Shen Kefeng

    2003-01-01

    Based upon the research of basin fills at the Bayantala basin, the genetic facies of host sediments have been ascertained and the target beds and their range are delineated. The sand bodies of the Upper Member of Tengge'er Formation deposited in fan delta front is favorable to the formation of uranium mineralization of phreatic-interlayer oxidation. The Saihantala Fm deposited in fluvial system can be divided into Lower Member and Upper Member based on depositional microfacies and paleoclimate. The Lower Member of braided system is the most important target bed enriched in organic matter where basal-channel-type uranium mineralization occurs. Features of alteration and mineralization suggest that the early-stage and the late-stage uranium mineralization are related to phreatic oxidation and interlayer oxidation (roll-type) respectively. Meanwhile, the secondary reduction has superimposed over the earlier mineralization in the area caused by hydrocarbons raising along faults

  20. Conditions of sedimentation of deposits of the lower section of the productive strata and their natural radioactivity

    International Nuclear Information System (INIS)

    Alieva, E.G.; Aliev, Ch.S.; Huseynov, D.A.

    2008-01-01

    In this article for the time for sedimentary deposits of the southern Caspian basin is an attempt use of the data of natural radioactivity of sediments in order to reconstruct their conditions sedimentation. The results obtained show a good comparability of the nature of the distribution of radioactive elements with the conditions of sedimentation. Clear contents of dependency is detected radioactive elements from the source of sedimentary material that can be successfully used in conducting the paleo facial and paleogeographic building.

  1. Sedimentological characteristics and depositional processes of sediment gravity flows in rift basins: The Palaeogene Dongying and Shahejie formations, Bohai Bay Basin, China

    Science.gov (United States)

    Liu, Lei; Chen, Hongde; Zhong, Yijiang; Wang, Jun; Xu, Changgui; Chen, Anqing; Du, Xiaofeng

    2017-10-01

    Sediment gravity flow deposits are common, particularly in sandy formations, but their origin has been a matter of debate and there is no consensus about the classification of such deposits. However, sediment gravity flow sandstones are economically important and have the potential to meet a growing demand in oil and gas exploration, so there is a drive to better understand them. This study focuses on sediment gravity flow deposits identified from well cores in Palaeogene deposits from the Liaodong Bay Depression in Bohai Bay Basin, China. We classify the sediment gravity flow deposits into eight lithofacies using lithological characteristics, grain size, and sedimentary structures, and interpret the associated depositional processes. Based on the scale, spatial distribution, and contact relationships of sediment gravity flow deposits, we defined six types of lithofacies associations (LAs) that reflect transformation processes and depositional morphology: LA1 (unconfined proximal breccia deposits), LA2 (confined channel deposits), LA3 (braided-channel lobe deposits), LA4 (unconfined lobe deposits), LA5 (distal sheet deposits), and LA6 (non-channelized sheet deposits). Finally, we established three depositional models that reflect the sedimentological characteristics and depositional processes of sediment gravity flow deposits: (1) slope-apron gravel-rich depositional model, which involves cohesive debris flows deposited as LA1 and dilute turbidity currents deposited as LA5; (2) non-channelized surge-like turbidity current depositional model, which mainly comprises sandy slumping, suspended load dominated turbidity currents, and dilute turbidity currents deposited as LA5 and LA6; and (3) channelized subaqueous-fan depositional model, which consists of non-cohesive bedload dominated turbidity currents, suspended load dominated turbidity currents, and dilute turbidity currents deposited as LA2-LA5, originating from sustained extrabasinal turbidity currents

  2. Preparation Of Deposited Sediment Sample By Casting Method For Environmental Study

    International Nuclear Information System (INIS)

    Hutabarat, Tommy; Ristin PI, Evarista

    2000-01-01

    The preparation of deposited sediment sample by c asting m ethod for environmental study has been carried out. This method comprises separation of size fraction and casting process. The deposited sediment samples were wet sieved to separate the size fraction of >500 mum, (250-500) mum, (125-250) mum and (63-125) mum and settling procedures were followed for the separation of (40-63) mum, (20-40) mum, (10-20) mum and o C, ashed at 450 o C, respectively. In the casting process of sample, it was used polyester rapid cure resin and methyl ethyl ketone peroxide (MEKP) hardener. The moulded sediment sample was poured onto caster, allow for 60 hours long. The aim of this method is to get the casted sample which can be used effectively, efficiently and to be avoided from contamination of each other samples. Before casting, samples were grinded up to be fine. The result shows that casting product is ready to be used for natural radionuclide analysis

  3. Patterns of floodplain sediment deposition along the regulated lower Roanoke River, North Carolina: annual, decadal, centennial scales

    Science.gov (United States)

    Hupp, Cliff R.; Schenk, Edward R.; Kroes, Daniel; Willard, Debra A.; Townsend, Phil A.; Peet, Robert K.

    2015-01-01

    The lower Roanoke River on the Coastal Plain of North Carolina is not embayed and maintains a floodplain that is among the largest on the mid-Atlantic Coast. This floodplain has been impacted by substantial aggradation in response to upstream colonial and post-colonial agriculture between the mid-eighteenth and mid-nineteenth centuries. Additionally, since the mid-twentieth century stream flow has been regulated by a series of high dams. We used artificial markers (clay pads), tree-ring (dendrogeomorphic) techniques, and pollen analyses to document sedimentation rates/amounts over short-, intermediate-, and long-term temporal scales, respectively. These analyses occurred along 58 transects at 378 stations throughout the lower river floodplain from near the Fall Line to the Albemarle Sound. Present sediment deposition rates ranged from 0.5 to 3.4 mm/y and 0.3 to 5.9 mm/y from clay pad and dendrogeomorphic analyses, respectively. Deposition rates systematically increased from upstream (high banks and floodplain) to downstream (low banks) reaches, except the lowest reaches. Conversely, legacy sediment deposition (A.D. 1725 to 1850) ranged from 5 to about 40 mm/y, downstream to upstream, respectively, and is apparently responsible for high banks upstream and large/wide levees along some of the middle stream reaches. Dam operations have selectively reduced levee deposition while facilitating continued backswamp deposition. A GIS-based model predicts 453,000 Mg of sediment is trapped annually on the floodplain and that little watershed-derived sediment reaches the Albemarle Sound. Nearly all sediment in transport and deposited is derived from the channel bed and banks. Legacy deposits (sources) and regulated discharges affect most aspects of present fluvial sedimentation dynamics. The lower river reflects complex relaxation conditions following both major human alterations, yet continues to provide the ecosystem service of sediment trapping.

  4. Sediment deposition rate in the Falefa River basin, Upolu Island, Samoa

    International Nuclear Information System (INIS)

    Terry, James P.; Kostaschuk, Ray A.; Garimella, Sitaram

    2006-01-01

    The 137 Cs method was employed to investigate the recent historical rate of sediment deposition on a lowland alluvial floodplain in the Falefa River basin, Upolu Island, Samoa. Caesium stratigraphy in the floodplain sediment profile was clearly defined, with a broad peak at 145-175 cm depth. The measured rate of vertical accretion over the last 40 years is 4.0 ± 0.4 cm per year. This rate exceeds observations in humid environments elsewhere, but is similar to that recorded on other tropical Pacific Islands. Available flow data for the Vaisigano River in Samoa give a 'near-catastrophic' index value of 0.6 for flood variability. This is associated with the occurrence of tropical cyclones and storms in the Samoa area. Large floods therefore probably contribute to the high rate of floodplain sedimentation on Upolu Island. A small but growing body of evidence suggests that fluvial sedimentation rates on tropical Pacific islands are some of the highest in the world

  5. Evaluating the Role of Small Impoundments in Legacy Sediment Storage

    Science.gov (United States)

    Bain, D. J.; Salant, N.; Green, M. B.; Wreschnig, A. J.; Urbanova, T.

    2009-12-01

    Recent research highlighting the prevalence of dams built for water power in the mid-1800s has led to suggestions that strategies for managing legacy sediment in the Eastern United States should be re-evaluated. However, the link between reach-scale observations of historic dam sites to processes at the catchment scale have not been examined, nor have the role of other, similar historic changes been evaluated. This presentation will compare dam dynamics, including mill density data and synthetic estimates of beaver populations with sedimentation rates recorded in sediment cores. If low-head dams were a dominant mechanism in sediment storage, we expect to see changes in sedimentation rates with the expatriation of the beaver and the rise and decline of water power. Further, we expect to see spatial variation in these changes as beaver and mill densities and potential sediment yield are spatially heterogeneous. Ultimately, dramatic changes in sediment yield due to land use and hydrological alterations likely drove sedimentation rates; the mechanistic importance of storage likely depends on temporal coincidence.

  6. Reduction of non-point source contaminants associated with road-deposited sediments by sweeping.

    Science.gov (United States)

    Kim, Do-Gun; Kang, Hee-Man; Ko, Seok-Oh

    2017-09-19

    Road-deposited sediments (RDS) on an expressway, residual RDS collected after sweeping, and RDS removed by means of sweeping were analyzed to evaluate the degree to which sweeping removed various non-point source contaminants. The total RDS load was 393.1 ± 80.3 kg/km and the RDS, residual RDS, and swept RDS were all highly polluted with organics, nutrients, and metals. Among the metals studied, Cu, Zn, Pb, Ni, Ca, and Fe were significantly enriched, and most of the contaminants were associated with particles within the size range from 63 μm to 2 mm. Sweeping reduced RDS and its associated contaminants by 33.3-49.1% on average. We also measured the biological oxygen demand (BOD) of RDS in the present work, representing to our knowledge the first time that this has been done; we found that RDS contains a significant amount of biodegradable organics and that the reduction of BOD by sweeping was higher than that of other contaminants. Significant correlations were found between the contaminants measured, indicating that the organics and the metals originated from both exhaust and non-exhaust particles. Meanwhile, the concentrations of Cu and Ni were higher in 63 μm-2 mm particles than in smaller particles, suggesting that some metals in RDS likely exist intrinsically in particles, rather than only as adsorbates on particle surfaces. Overall, the results in this study showed that sweeping to collect RDS can be a good alternative for reduction of contaminants in runoff.

  7. Heavy metals in the finest size fractions of road-deposited sediments.

    Science.gov (United States)

    Lanzerstorfer, Christof

    2018-08-01

    The concentration of heavy metals in urban road-deposited sediments (RDS) can be used as an indicator for environmental pollution. Thus, their occurrence has been studied in whole road dust samples as well as in size fractions obtained by sieving. Because of the limitations of size separation by sieving little information is available about heavy metal concentrations in the road dust size fractions heavy metals concentrations and size distribution. According to the Geoaccumulation Index the pollution of the road dust samples deceased in the following order: Sb » As > Cu ≈ Zn > Cr > Cd ≈ Pb ≈ Mn > Ni > Co ≈ V. For all heavy metals the concentration was higher in the fine size fractions compared to the coarse size fractions, while the concentration of Sr was size-independent. The enrichment of the heavy metals in the finest size fraction compared to the whole RDS  Sb > (Cu) ≈ Zn ≈ Pb > As ≈ V » Mn. The approximation of the size dependence of the concentration as a function of the particle size by power functions worked very well. The correlation between particle size and concentration was high for all heavy metals. The increased heavy metals concentrations in the finest size fractions should be considered in the evaluation of the contribution of road dust re-suspension to the heavy metal contamination of atmospheric dust. Thereby, power functions can be used to describe the size dependence of the concentration. Copyright © 2018 Elsevier Ltd. All rights reserved.

  8. Millennial-scale record of overwash deposits preserved within lagoon sediments from the Arabian Peninsula

    Science.gov (United States)

    Griffis, A. M.; Jessica, P.; Reinhardt, E. G.; Kosciuch, T. J.; Kovacs, S. E.; Hoffmann, G.

    2017-12-01

    Coastlines along the Arabian Sea are susceptible to tsunami-related inundation due to their proximity to the Makran Subduction Zone (MSZ). This subduction zone has seen decades of low intensity events, but has historically produced large tsunamigenic-earthquakes that have impacted the 100 million people living along the Arabian Sea. One major problem in assessing the seismic risk of the MSZ is that the historical record of events are spatially and temporally limited and rely heavily on eye witness accounts. This hinders our ability to forecast the potential magnitude and recurrence intervals of earthquakes and tsunamis that can be expected in the future. Sediments deposited by paleotsunamis are useful as they expand the decadal record of events to include millennial timescales that more accurately capture the full range of magnitudes and recurrence intervals. On November 28, 1945 a 8.1 Mw earthquake originating from the MSZ generated a tsunami inundating coastlines along the Arabian Sea with wave heights up to 13m. At Sur, a small village on the northeastern coastline of Oman, the tsunami deposited a laterally continuous shell-rich layer within a 12 km2 lagoon. This layer contained distinctive taphonomic assemblages of foraminifera and bivalves. Below the 1945 shelly deposit at Sur Lagoon, seven anomalous sand layers were found preserved within fine-grained lagoonal sediment. These layers of medium-coarse sands range in thickness from 5 to 35 cm and are separated by sandy-mud sediment. Grain size analysis shows that these anomalously coarse layers are followed by an abrupt return to lagoonal mud. The sand layers have features consistent with the 1945 tsunami deposit such as fining upward trends, sharp basal contact, and marine foraminifera (e.g., Amphistegina sp., planktics). In contrast, the surrounding lagoon deposits are generally massive, finer in grain size, and contain foraminiferal species typically found in shallow quiescent coastal environments (e

  9. Effects of deposition of heavy-metal-polluted harbor mud on microbial diversity and metal resistance in sandy marine sediments

    DEFF Research Database (Denmark)

    Toes, Ann-Charlotte M; Finke, Niko; Kuenen, J Gijs

    2008-01-01

    Deposition of dredged harbor sediments in relatively undisturbed ecosystems is often considered a viable option for confinement of pollutants and possible natural attenuation. This study investigated the effects of deposition of heavy-metal-polluted sludge on the microbial diversity of sandy...... the finding that some groups of clones were shared between the metal-impacted sandy sediment and the harbor control, comparative analyses showed that the two sediments were significantly different in community composition. Consequences of redeposition of metal-polluted sediment were primarily underlined...... with cultivation-dependent techniques. Toxicity tests showed that the percentage of Cd- and Cu-tolerant aerobic heterotrophs was highest among isolates from the sandy sediment with metal-polluted mud on top....

  10. Consequences of land use and climate changes on sediment deposition in estuaries during the last centuries

    Science.gov (United States)

    Poirier, Clément; Chaumillon, Eric; Arnaud, Fabien; Goubert, Evelyne; Sauriau, Pierre-Guy; Caurant, Florence

    2010-05-01

    Estuaries are the downstream end-member of fluvial systems. They are experiencing high sedimentation rates, thus providing good opportunities for high resolution studies of Holocene environmental changes at the land/ocean interface. From a thorough literature survey, it appears that a rapid siltation and/or an increase in sedimentation rate were recorded in many estuarine environments, concomitantly to major migrations of human population throughout the world, both in time and space. It has been clearly related to an increase in sediment supply to estuaries in Minor Asia (Bronze Age, e.g. Spezzaferri et al, 2000) and in North America and Southwest Pacific (18th and 19th centuries, e.g. Goff, 1997), in response to deforestation on catchment areas. However, this relationship is less obvious in Europe (Sorrel et al., 2009), because deforestation occurred concomitantly to climate changes of the last millennium (climate instability at the end of Medieval Warm Period, Little Ice Age) that can also explain an increase in soil erosion. Indeed, these hypotheses have been proposed to explain a similar change in Marennes-Oléron Bay (Atlantic coast of France), which consists in the sudden deposition of a few meters-thick mud drape on basal mixed mud and sand bodies (Billeaud et al., 2005). The methods used to investigate this estuarine bay so far (very high resolution seismic stratigraphy, grain size analysis and radiocarbon dating) provided relevant information about recent environmental changes, but new data are now needed for further investigation. In the present study, we provide a multi-proxy analysis of the Marennes-Oléron Bay mud drape. A new 8 m-long core (M7UC01) was sampled on an intertidal flat, its location being determined on the basis of seismic stratigraphy. Core processing included visual description, physical measurements, grain size analysis every 2.5 to 5 cm, AMS radiocarbon dating, XRF core scanning, clay mineralogy and Rock Eval analysis. Fossil molluscs

  11. Erosion and sediment deposition evaluation on slopes under different tillage systems in the Cerrado region using the {sup 137}Cs fallout technique; Analise da distribuicao do fallout do {sup 137}Cs na avaliacao da erosao e deposicao de sedimentos em sistemas de manejo de solo sob Cerrado

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, Robson Clayton Jacques

    2010-07-01

    In Brazil, the expansion of agricultural areas causes several problems on natural resources. With the increasing occupation of the Cerrado region by agriculture, a series of environmental problems like deforestation, soil erosion and soil compaction are appearing and causing radical transformations in the natural landscape due to removing almost all native vegetation. The conventional tillage system (CTS) is considered an inadequate form of soil management for its frequently irremediable consequences of soil compaction and soil erosion, and the no till system (NTS) makes the maintenance of the soil conditions possible, letting them close to the natural environment, thus reducing rates of soil erosion. The objective of this work was to evaluate the efficiency of riparian forests in the retention of sediments originated for three different tillage systems, through the fallout {sup 137}CS redistribution technique, the Universal Soil Loss Equation (USLE) and some physical and chemical parameters that indicate the structural conditions of the soils of Goiatuba and Jandaia-GO. In the three areas, soil profiles were collected in three layers of 20 cm (0-20, 20-40 and 40-60 cm) at distinct points located along linear transects in the direction of the maximum slope until the riparian forest. In the riparian forest of each area, trenches were opened and soil was sampled to evaluate the activity of {sup 137}Cs and the physical and chemical parameters of soil. Detection of the activity of {sup 137}Cs was made with a gamma ray detector model (GEM-20180P, EG and ORTEC) connected to a multichannel analyzer. The comparison of averages was made using the Tukey test at 5% level of significance. The. results indicated that, the three soil tillage systems presented high rates of soil erosion and deposition of sediments and the riparian forest of the areas under CTS, NTS and pasture, located downstream received great amounts of sediments, and that only the riparian forest of CTS was

  12. Combining trace elements micro-analysis in deposited dredged sediments: EPMA and μ-XRF analysis

    International Nuclear Information System (INIS)

    Poitevin, A; Lerouge, C; Wille, G; Bataillard, P; Quinn, P; Hennet, L

    2012-01-01

    Since deposited dredged sediments are rich in metallic contaminants, they present a risk for environment. This work aims to study dredged sediments chemical composition, identify metal-carrier minerals and understand their mobility. Combining chemical and spectroscopic techniques at multi-scale for an integrative approach of trace elements (zinc, lead, iron) behaviour is therefore necessary. The global mineralogy and the chemistry of the sediment were determined by X-ray diffraction and fluorescence (XRF), respectively. Zn and Pb enriched fractions were separated using a sequential chemical extraction procedure and measured by inductively coupled plasma atomic emission and mass spectroscopy. Microanalyses using scanning electron microscopy (SEM), electron microprobe microanalysis (EPMA), combined with synchrotron radiation X-ray fluorescence (μ-XRF) were carried out to characterize mineralogical phases and identify Zn and Pb carrier minerals. Iron oxyhydroxides and iron sulphides were consistently identify as Zn and Pb carriers. The assumption that carbonate fraction was the major Zn carried phase, as demonstrated by chemical extraction results, was not verified by EPMA or μ-XRF.

  13. Recent changes in mercury deposition and primary productivity inferred from sediments of lakes from the Hudson Bay Lowlands, Ontario, Canada

    International Nuclear Information System (INIS)

    Brazeau, Michelle L.; Poulain, Alexandre J.; Paterson, Andrew M.; Keller, Wendel; Sanei, Hamed; Blais, Jules M.

    2013-01-01

    Spatial and temporal changes in mercury (Hg) concentrations and organic carbon in lake sediments were examined from the Hudson Bay Lowlands to investigate whether Hg deposition to sediments is related to indicators of autochthonous production. Total organic carbon, “S2” carbon (mainly algal-derived OC), C:N and ∂ 13 C indicators suggest an increase in autochthonous productivity in recent decades. Up-core profiles of S2 concentrations and fluxes were significantly correlated with Hg suggesting that varying algal matter scavenging of Hg from the water column may play an important role in the temporal profiles of Hg throughout the sediment cores. Absence of significant relationship between total Hg and methyl Hg (MeHg) in surficial sediments suggested that inorganic Hg supply does not limit MeHg production. MeHg and OC were highly correlated across lakes in surface and deep sediment layers, indicating that sediment organic matter content explains part of the spatial variation in MeHg concentrations between lakes. - Highlights: ► Hg concentrations in sediment cores correlate with autochthonous organic production. ► Inorganic Hg supply in sediment does not limit MeHg production. ► Sediment methylmercury concentration is highly correlated with organic C content. - Increased mercury concentrations in lake sediment cores coincide with evidence of increased autochthonous production in lakes of the Hudson Bay Lowlands, Canada.

  14. Sediment transport and deposition in the lower Missouri River during the 2011 flood

    Science.gov (United States)

    Alexander, Jason S.; Jacobson, Robert B.; Rus, David L.

    2013-01-01

    Floodwater in the Missouri River in 2011 originated in upper-basin regions and tributaries, and then travelled through a series of large flood-control reservoirs, setting records for total runoff volume entering all six Missouri River main-stem reservoirs. The flooding lasted as long as 3 months. The U.S Geological Survey (USGS) examined sediment transport and deposition in the lower Missouri River in 2011 to investigate how the geography of floodwater sources, in particular the decanting effects of the Missouri River main-stem reservoir system, coupled with the longitudinal characteristics of civil infrastructure and valley-bottom topography, affected sediment transport and deposition in this large, regulated river system. During the flood conditions in 2011, the USGS, in cooperation with the U.S. Army Corps of Engineers, monitored suspended-sediment transport at six primary streamgages along the length of the lower Missouri River. Measured suspended-sediment concentration (SSC) in the lower Missouri River varied from approximately 150 milligrams per liter (mg/L) to 2,000 mg/L from January 1 to September 30, 2011. Median SSC increased in the downstream direction from 355 mg/L at Sioux City, Iowa, to 490 mg/L at Hermann, Missouri. The highest SSCs were measured downstream from Omaha, Nebraska, in late February when snowmelt runoff from tributaries, which were draining zones of high-sediment production, was entering the lower Missouri River, and releases of water at Gavins Point Dam were small. The combination of dilute releases of water at Gavins Point Dam and low streamflows in lower Missouri River tributaries caused sustained lowering of SSC at all streamgages from early July through late August. Suspended-sediment ranged from 5 percent washload (PW; percent silt and clay) to as much as 98 percent in the lower Missouri River from January 1 to September 30, 2011. Median PW increased in the downstream direction from 24 percent at Sioux City, Iowa, to 78 percent at

  15. Soft-sediment deformation structures in cores from lacustrine slurry deposits of the Late Triassic Yanchang Fm. (central China

    Directory of Open Access Journals (Sweden)

    Yang Renchao

    2016-09-01

    Full Text Available The fine-grained autochthonous sedimentation in the deep part of a Late Triassic lake was frequently interrupted by gravity-induced mass flows. Some of these mass flows were so rich in water that they must have represented slurries. This can be deduced from the soft-sediment deformation structures that abound in cores from these lacustrine deposits which constitute the Yanchang Fm., which is present in the Ordos Basin (central China.

  16. Tsunami deposits

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-15

    The NSC (the Nuclear Safety Commission of Japan) demand to survey on tsunami deposits by use of various technical methods (Dec. 2011), because tsunami deposits have useful information on tsunami activity, tsunami source etc. However, there are no guidelines on tsunami deposit survey in JAPAN. In order to prepare the guideline of tsunami deposits survey and evaluation and to develop the method of tsunami source estimation on the basis of tsunami deposits, JNES carried out the following issues; (1) organizing information of paleoseismological record and tsunami deposit by literature research, (2) field survey on tsunami deposit, and (3) designing the analysis code of sediment transport due to tsunami. As to (1), we organize the information gained about tsunami deposits in the database. As to (2), we consolidate methods for surveying and identifying tsunami deposits in the lake based on results of the field survey in Fukui Pref., carried out by JNES. In addition, as to (3), we design the experimental instrument for hydraulic experiment on sediment transport and sedimentation due to tsunamis. These results are reflected in the guideline on the tsunami deposits survey and evaluation. (author)

  17. Tsunami deposits

    International Nuclear Information System (INIS)

    2013-01-01

    The NSC (the Nuclear Safety Commission of Japan) demand to survey on tsunami deposits by use of various technical methods (Dec. 2011), because tsunami deposits have useful information on tsunami activity, tsunami source etc. However, there are no guidelines on tsunami deposit survey in JAPAN. In order to prepare the guideline of tsunami deposits survey and evaluation and to develop the method of tsunami source estimation on the basis of tsunami deposits, JNES carried out the following issues; (1) organizing information of paleoseismological record and tsunami deposit by literature research, (2) field survey on tsunami deposit, and (3) designing the analysis code of sediment transport due to tsunami. As to (1), we organize the information gained about tsunami deposits in the database. As to (2), we consolidate methods for surveying and identifying tsunami deposits in the lake based on results of the field survey in Fukui Pref., carried out by JNES. In addition, as to (3), we design the experimental instrument for hydraulic experiment on sediment transport and sedimentation due to tsunamis. These results are reflected in the guideline on the tsunami deposits survey and evaluation. (author)

  18. Morphology and processes associated with the accumulation of the fine-grained sediment deposit on the southern New England shelf

    Science.gov (United States)

    Twichell, David C.; McClennen, Charles E.; Butman, Bradford

    1981-01-01

    A 13,000 km2 area of the southern New England Continental Shelf which is covered by anomalously fine-grained sediment has been surveyed by means of high-resolution, seismic-reflection and side-scan sonar techniques to map its morphology and structure, and a near-bottom instrument system contributed to understanding present activity of the deposit. Seismic-reflection profiles show that the fine-grained deposit, which is as much as 13 m thick, has accumulated during the last transgression because it rests on a reflector that is geomorphically similar to and continuous with the Holocene transgressive sand sheet still exposed on the shelf to the west. The ridge and swale topography comprising the sand sheet on the shelf off New Jersey and Long Island are relict in origin as these same features are found buried under the fine sediment deposit. Southwestward migrating megaripples observed on the sonographs in the eastern part of the deposit are evidence that sediment is still actively accumulating in this area. In the western part of the deposit, where surface sediment is composed of silt plus clay, evidence of present sediment mobility consists of changes in the near-bottom, suspended-matter concentrations primarily associated with storms. Nantucket Shoals and Georges Bank are thought to be the sources for the fine-textured sediment. Storms and strong tidal currents in these shoal areas may still erode available fine-grained material, which then is transported westward by the mean drift to the southern New England Shelf, where a comparatively tranquil environment permits deposition of the fine material.

  19. Sediment deposition and trends and transport of phosphorus and other chemical constituents, Cheney Reservoir watershed, south-central Kansas

    Science.gov (United States)

    Mau, D.P.

    2001-01-01

    Sediment deposition, water-quality trends, and mass transport of phosphorus, nitrogen, selected trace elements, and selected pesticides within the Cheney Reservoir watershed in south-central Kansas were investigated using bathymetric survey data and reservoir bottom-sediment cores. Sediment loads in the reservoir were investigated by comparing 1964 topographic data to 1998 bathymetric survey data. Approximately 7,100 acre-feet of sediment deposition occurred in Cheney Reservoir from 1965 through 1998. As of 1998, sediment had filled 27 percent of the reservoir's inactive conservation storage pool, which is less than the design estimate of 34 percent. Mean annual sediment deposition was 209 acre-feet per year, or 0.22 acre-feet per year per square mile, and the mean annual sediment load was 453 million pounds per year. During the 3-year period from 1997 through 1999, 23 sediment cores were collected from the reservoir, and subsamples were analyzed for nutrients (phosphorus and nitrogen species), selected trace elements, and selected organic pesticides. Mean concentrations of total phosphorus in reservoir bottom sediment ranged from 94 milligrams per kilogram at the upstream end of the reservoir to 710 milligrams per kilogram farther downstream near the reservoir dam. The mean concentration for all sites was 480 milligrams per kilogram. Total phosphorus concentrations were greatest when more silt- and clay-sized particles were present. The implications are that if anoxic conditions (inadequate oxygen) occur near the dam, phosphorus could be released from the sediment and affect the drinking-water supply. Analysis of selected cores also indicates that total phosphorus concentrations in the reservoir sediment increased over time and were probably the result of nonpoint-source activities in the watershed, such as increased fertilizer use and livestock production. Mean annual phosphorus loading to Cheney Reservoir was estimated to be 226,000 pounds per year on the basis

  20. Evaluation of sedimentation rates by 210-Pb, in water bodies of semiarid and arid area

    International Nuclear Information System (INIS)

    Afif, H.; Bouhlassa, S.

    1994-01-01

    As Morocco is located in semiarid to arid area, it is subject to irregular intensity and quantity of rainfall regime. So, its reservoirs suffer from severe siltation problems resulting from severe erosion phenomenon. The dating method based on an excess of 210-Pb in reservoir sediments, successfully used in areas of low erosion rate, cannot be extend to our case owing the dilution of low concentration of atmospheric 210-Pb in high sediment flux. Whenever used, this method leads to evaluate the siltation rate, which is a very interesting parameter in dam water management. An alternative to this method has been developed, based on the variation of 210-Pb sediment cores. Its application to a set of sediment cores indicates that 210-Pb is strongly and preferentially adsorbed in the clay. This could be used, as an indication of the annual deposition limits, and to determine variations of sedimentation rates in time and space in the reservoir. 2 figs., 1 tab., 1 ref. (author)

  1. The analyzing stratum formation and sediment environment using TEM for finding sandstone type uranium deposits in Mahuangquan area

    International Nuclear Information System (INIS)

    Zhao Xigang; He Jianguo; Zhao Cuiping; Lou Hansheng

    2010-01-01

    Transient electromagnetic method (TEM) is used to detect deep geological information for insidious sandstone type uranium deposits in Mahuangquan area. TEM surveying data is processed to build the relation between resistance rate and different petrology, to ensure three large electronic strata, and to explain the space position of sediment center and alluvial fan. Combining with ore control factors of sandstone type uranium deposit, it can conclude that the slope area and the alluvial fan are the key areas for further exploration work. (authors)

  2. Evaluation of the sedimentation rate in a sediment profile of Bortolan Dam, MG, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, Heleine C. de; Soares, Flávio V.T.S.; Taddei, Maria Helena T.; Mazzilli, Barbara P., E-mail: heleine.almeida@ipen.br, E-mail: mhtaddei@cnen.gov.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Laboratório de Poços de Caldas (LAPOC/CNEN-MG), Pocos de Caldas, MG (Brazil)

    2017-11-01

    Volcanic extrusion is one of the main causes for the high levels of environmental radioactivity in the region of Poços de Caldas (MG, Brazil). Uranium mining during the 80's further increased the background radiation in the region, especially in the Ribeirao das Antas watershed, where Bortolan Dam is located. Besides the uranium mining facility operating in the region, other activities, such as agriculture, were also responsible for the enhancement of the levels of radioactivity. The dam sediment profile provides an appropriate compartment for the study of the temporal variation of these radionuclides and for the evaluation of anthropogenic contamination. The main aim of this study is to evaluate the sedimentation rate and the dating of a profile collected in Bortolan Dam, by using the geochronology method. The activity concentration of {sup 226}Ra and {sup 210}Pb were measured in the sediment profile by gamma spectrometry. The concentration of {sup 226}Ra and {sup 210}Pb varied from (217 ± 9) Bq kg{sup -1} to (286 ± 12) Bq kg{sup -1} and from (262 ± 11) Bq kg{sup -1} to (322 ± 34) Bq·kg{sup -1} respectively; and the sedimentation rates varied from 0.021 to 0.144 g cm{sup -2}y{sup -1}. (author)

  3. Evaluation of the sedimentation rate in a sediment profile of Bortolan Dam, MG, Brazil

    International Nuclear Information System (INIS)

    Almeida, Heleine C. de; Soares, Flávio V.T.S.; Taddei, Maria Helena T.; Mazzilli, Barbara P.

    2017-01-01

    Volcanic extrusion is one of the main causes for the high levels of environmental radioactivity in the region of Poços de Caldas (MG, Brazil). Uranium mining during the 80's further increased the background radiation in the region, especially in the Ribeirao das Antas watershed, where Bortolan Dam is located. Besides the uranium mining facility operating in the region, other activities, such as agriculture, were also responsible for the enhancement of the levels of radioactivity. The dam sediment profile provides an appropriate compartment for the study of the temporal variation of these radionuclides and for the evaluation of anthropogenic contamination. The main aim of this study is to evaluate the sedimentation rate and the dating of a profile collected in Bortolan Dam, by using the geochronology method. The activity concentration of "2"2"6Ra and "2"1"0Pb were measured in the sediment profile by gamma spectrometry. The concentration of "2"2"6Ra and "2"1"0Pb varied from (217 ± 9) Bq kg"-"1 to (286 ± 12) Bq kg"-"1 and from (262 ± 11) Bq kg"-"1 to (322 ± 34) Bq·kg"-"1 respectively; and the sedimentation rates varied from 0.021 to 0.144 g cm"-"2y"-"1. (author)

  4. Permeability of sediment cores from methane hydrate deposit in the Eastern Nankai Trough, Japan

    Science.gov (United States)

    Konno, Y.; Yoneda, J.; Egawa, K.; Ito, T.; Jin, Y.; Kida, M.; Suzuki, K.; Nakatsuka, Y.; Nagao, J.

    2013-12-01

    Effective and absolute permeability are key parameters for gas production from methane-hydrate-bearing sandy sediments. Effective and/or absolute permeability have been measured using methane-hydrate-bearing sandy cores and clayey and silty cores recovered from Daini Atsumi Knoll in the Eastern Nankai Trough during the 2012 JOGMEC/JAPEX Pressure coring operation. Liquid-nitrogen-immersed cores were prepared by rapid depressurization of pressure cores recovered by a pressure coring system referred to as the Hybrid PCS. Cores were shaped cylindrically on a lathe with spraying of liquid nitrogen to prevent hydrate dissociation. Permeability was measured by a flooding test or a pressure relaxation method under near in-situ pressure and temperature conditions. Measured effective permeability of hydrate-bearing sediments is less than tens of md, which are order of magnitude less than absolute permeability. Absolute permeability of clayey cores is approximately tens of μd, which would perform a sealing function as cap rocks. Permeability reduction due to a swelling effect was observed for a silty core during flooding test of pure water mimicking hydrate-dissociation-water. Swelling effect may cause production formation damage especially at a later stage of gas production from methane hydrate deposits. This study was financially supported by the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) that carries out Japan's Methane Hydrate R&D Program conducted by the Ministry of Economy, Trade and Industry (METI).

  5. Controls of tectonics and sediment source locations on along-strike variations in transgressive deposits on the northern California margin

    Science.gov (United States)

    Spinelli, G.A.; Field, M.E.

    2003-01-01

    We identify two surfaces in the shallow subsurface on the Eel River margin offshore northern California, a lowstand erosion surface, likely formed during the last glacial maximum, and an overlying surface likely formed during the most recent transgression of the shoreline. The lowstand erosion surface, which extends from the inner shelf to near the shelfbreak and from the Eel River to Trinidad Head (???80 km), truncates underlying strata on the shelf. Above the surface, inferred transgressive coastal and estuarine sedimentary units separate it from the transgressive surface on the shelf. Early in the transgression, Eel River sediment was likely both transported down the Eel Canyon and dispersed on the slope, allowing transgressive coastal sediment from the smaller Mad River to accumulate in a recognizable deposit on the shelf. The location of coastal Mad River sediment accumulation was controlled by the location of the paleo-Mad River. Throughout the remainder of the transgression, dispersed sediment from the Eel River accumulated an average of 20 m of onlapping shelf deposits. The distribution and thickness of these transgressive marine units was strongly modified by northwest-southeast trending folds. Thick sediment packages accumulated over structural lows in the lowstand surface. The thinnest sediment accumulations (0-10 m) were deposited over structural highs along faults and uplifting anticlines. The Eel margin, an active margin with steep, high sediment-load streams, has developed a thick transgressive systems tract. On this margin sediment accumulates as rapidly as the processes of uplift and downwarp locally create and destroy accommodation space. Sequence stratigraphic models of tectonically active margins should account for variations in accommodation space along margins as well as across them. ?? 2003 Elsevier Science B.V. All rights reserved.

  6. Observations on the relation between lacustrine facies and uranium deposits in continental sediments

    International Nuclear Information System (INIS)

    Noble, E.A.

    1981-01-01

    A recent sedimentological concept and approach in the evaluation of lacustrine deposition environments for their geological uranium potential are described. The presence of certain types of limonite seems to be a key factor in the process of leaching, the formation of pyrite and the precipitation of uranium. (author)

  7. Sediment transport modeling in deposited bed sewers: unified form of May's equations using the particle swarm optimization algorithm.

    Science.gov (United States)

    Safari, Mir Jafar Sadegh; Shirzad, Akbar; Mohammadi, Mirali

    2017-08-01

    May proposed two dimensionless parameters of transport (η) and mobility (F s ) for self-cleansing design of sewers with deposited bed condition. The relationships between those two parameters were introduced in conditional form for specific ranges of F s , which makes it difficult to use as a practical tool for sewer design. In this study, using the same experimental data used by May and employing the particle swarm optimization algorithm, a unified equation is recommended based on η and F s . The developed model is compared with original May relationships as well as corresponding models available in the literature. A large amount of data taken from the literature is used for the models' evaluation. The results demonstrate that the developed model in this study is superior to May and other existing models in the literature. Due to the fact that in May's dimensionless parameters more effective variables in the sediment transport process in sewers with deposited bed condition are considered, it is concluded that the revised May equation proposed in this study is a reliable model for sewer design.

  8. Evaluation of Heavy Metals in Stream Sediments from Abakaliki Pb ...

    African Journals Online (AJOL)

    PROF HORSFALL

    Evaluation of Heavy Metals in Stream Sediments from Abakaliki Pb – Zn Ore Mining. Areas of Ebonyi ... produced both for local consumption and also for food supplies to other .... of deionised water using a pH-meter (Aqualytica. Model pH 17).

  9. Spatial and temporal variability of sediment deposition on artificial-lawn traps in a floodplain of the River Elbe

    Energy Technology Data Exchange (ETDEWEB)

    Baborowski, M. [Department of River Ecology, Helmholtz Centre for Environmental Research - UFZ, Brueckstrasse 3a, 39114 Magdeburg (Germany)]. E-mail: martina.baborowski@ufz.de; Buettner, O. [Department of Lake Research, Helmholtz Centre for Environmental Research - UFZ, Brueckstrasse 3a, 39114 Magdeburg (Germany); Morgenstern, P. [Department of Analytical Chemistry, Helmholtz Centre for Environmental Research - UFZ, Permoserstrasse 15, 04318 Leipzig (Germany); Krueger, F. [ELANA Boden Wasser Monitoring, Dorfstrasse 55, 39615 Falkenberg (Germany); Lobe, I. [Department of River Ecology, Helmholtz Centre for Environmental Research - UFZ, Brueckstrasse 3a, 39114 Magdeburg (Germany); Rupp, H. [Department of Soil Physics, Helmholtz Centre for Environmental Research - UFZ, Dorfstrasse 55, 39615 Falkenberg (Germany); Tuempling, W. v. [Department of River Ecology, Helmholtz Centre for Environmental Research - UFZ, Brueckstrasse 3a, 39114 Magdeburg (Germany)

    2007-08-15

    Artificial-lawn mats were used as sediment traps in floodplains to measure sediment input and composition during flood events. To estimate the natural variability, 10 traps were installed during two flood waves at three different morphological units in a meander loop of the River Elbe. The geochemical composition of deposited and suspended matter was compared. The sediment input showed weak correlations with concentration and composition of river water. It also correlated poorly with flood duration and level as well as distance of trap position from the main river. This is due to the high variability of the inundation, different morphological conditions and the variability of sources. The composition of the deposits and the suspended matter in the river water was comparable. Hence, for the investigated river reach, the expected pollution of the floodplain sediments can be derived from the pollution of the suspended matter in the river during the flood wave. - The deposition of polluted sediments on floodplains is characterised by a high local variability.

  10. Spatial and temporal variability of sediment deposition on artificial-lawn traps in a floodplain of the River Elbe

    International Nuclear Information System (INIS)

    Baborowski, M.; Buettner, O.; Morgenstern, P.; Krueger, F.; Lobe, I.; Rupp, H.; Tuempling, W. v.

    2007-01-01

    Artificial-lawn mats were used as sediment traps in floodplains to measure sediment input and composition during flood events. To estimate the natural variability, 10 traps were installed during two flood waves at three different morphological units in a meander loop of the River Elbe. The geochemical composition of deposited and suspended matter was compared. The sediment input showed weak correlations with concentration and composition of river water. It also correlated poorly with flood duration and level as well as distance of trap position from the main river. This is due to the high variability of the inundation, different morphological conditions and the variability of sources. The composition of the deposits and the suspended matter in the river water was comparable. Hence, for the investigated river reach, the expected pollution of the floodplain sediments can be derived from the pollution of the suspended matter in the river during the flood wave. - The deposition of polluted sediments on floodplains is characterised by a high local variability

  11. Dry deposition models for radionuclides dispersed in air: a new approach for deposition velocity evaluation schema

    Science.gov (United States)

    Giardina, M.; Buffa, P.; Cervone, A.; De Rosa, F.; Lombardo, C.; Casamirra, M.

    2017-11-01

    In the framework of a National Research Program funded by the Italian Minister of Economic Development, the Department of Energy, Information Engineering and Mathematical Models (DEIM) of Palermo University and ENEA Research Centre of Bologna, Italy are performing several research activities to study physical models and mathematical approaches aimed at investigating dry deposition mechanisms of radioactive pollutants. On the basis of such studies, a new approach to evaluate the dry deposition velocity for particles is proposed. Comparisons with some literature experimental data show that the proposed dry deposition scheme can capture the main phenomena involved in the dry deposition process successfully.

  12. Data Evaluation Report for the Lower Rouge River Sediment Investigation

    Science.gov (United States)

    Describes a study of contaminated sediment, analyzes results, and makes recommendations for sediment remediation. Includes aerial views of study locations, photo log, data tables of sediment analysis.

  13. Response of stream-breeding salamander larvae to sediment deposition in southern Appalachian (U.S.A.) headwater streams

    Science.gov (United States)

    S. Conner Keitzer; Reuben. Goforth

    2012-01-01

    Summary 1. Increased fine sediment deposition is a prevalent threat to stream biodiversity and has been shown to impact stream-breeding salamanders negatively. However, their complex life histories make it difficult to determine which stage is affected. 2. We conducted field experiments from 26 August to 11 September 2010 and 11 October to 11...

  14. Stress evaluation of chemical vapor deposited silicon dioxide films

    International Nuclear Information System (INIS)

    Maeda, Masahiko; Itsumi, Manabu

    2002-01-01

    Film stress of chemical vapor deposited silicon dioxide films was evaluated. All of the deposited films show tensile intrinsic stresses. Oxygen partial pressure dependence of the intrinsic stress is very close to that of deposition rate. The intrinsic stress increases with increasing the deposition rate under the same deposition temperature, and decreases with increasing substrate temperature. Electron spin resonance (ESR) active defects in the films were observed when the films were deposited at 380 deg. C and 450 deg. C. The ESR signal intensity decreases drastically with increasing deposition temperature. The intrinsic stress correlates very closely to the intensity of the ESR-active defects, that is, the films with larger intrinsic stress have larger ESR-active defects. It is considered that the intrinsic stress was generated because the voids caused by local bond disorder were formed during random network formation among the SiO 4 tetrahedra. This local bond disorder also causes the ESR-active defects

  15. A coupled modelling effort to study the fate of contaminated sediments downstream of the Coles Hill deposit, Virginia, USA

    Directory of Open Access Journals (Sweden)

    C. F. Castro-Bolinaga

    2015-03-01

    Full Text Available This paper presents the preliminary results of a coupled modelling effort to study the fate of tailings (radioactive waste-by product downstream of the Coles Hill uranium deposit located in Virginia, USA. The implementation of the overall modelling process includes a one-dimensional hydraulic model to qualitatively characterize the sediment transport process under severe flooding conditions downstream of the potential mining site, a two-dimensional ANSYS Fluent model to simulate the release of tailings from a containment cell located partially above the local ground surface into the nearby streams, and a one-dimensional finite-volume sediment transport model to examine the propagation of a tailings sediment pulse in the river network located downstream. The findings of this investigation aim to assist in estimating the potential impacts that tailings would have if they were transported into rivers and reservoirs located downstream of the Coles Hill deposit that serve as municipal drinking water supplies.

  16. Fine-grained sediment deposition on mussel beds in the Oosterschelde (The Netherlands), determined from echosoundings, radio-isotopes and biodeposition field experiments

    International Nuclear Information System (INIS)

    Brinke, W.B.M. ten; Augustinus, P.G.E.F.

    1995-01-01

    Sedimentation rates of 5-20 cm year -1 were calculated from 137 Cs + 134 Cs activity profiles and echosoundings in a mussel cultivation area in the western part of the Oosterschelde. Sedimentation rates based on 210 Pb activity profiles are far too low, mainly due to the deposition of 'aged' sediment, i.e. sediment eroded elsewhere inside the basin and not fully enriched with 210 Pb at the moment of deposition. Also, specific adsorption to the finest sediment components, mixing, winnowing, and mobilization of the caesium have affected the lead and caesium profiles. Field experiments on mussel plots showed that mussels deposit 5-10 cm of fine-grained sediment during the summer. This biodeposition about equals the settling from flocculation in the water column. Micro-fabric microscope studies revealed that pellets do not dominate the sediments, indicating that some of the pellets are broken down or resuspended. (author)

  17. Age, distribution, and significance within a sediment budget, of in-channel depositional surfaces in the Normanby River, Queensland, Australia

    Science.gov (United States)

    Pietsch, T. J.; Brooks, A. P.; Spencer, J.; Olley, J. M.; Borombovits, D.

    2015-06-01

    We present the results of investigations into alluvial deposition in the catchment of the Normanby River, which flows into Princess Charlotte Bay (PCB) in the northern part of the Great Barrier Reef Lagoon. Our focus is on the fine fraction (bank attached bars or inset or inner floodplains, these more or less flat-lying surfaces within the macro-channel have hitherto received little attention in sediment budgeting models. We use high resolution LiDAR based mapping combined with optical dating of exposures cut into these in-channel deposits to compare their aggradation rates with those found in other depositional zones in the catchment, namely the floodplain and coastal plain. In total 59 single grain OSL dates were produced across 21 stratigraphic profiles at 14 sites distributed though the 24 226 km2 catchment. In-channel storage in these inset features is a significant component of the contemporary fine sediment budget (i.e. recent decades/last century), annually equivalent to more than 50% of the volume entering the channel network from hillslopes and subsoil sources. Therefore, at the very least, in-channel storage of fine material needs to be incorporated into sediment budgeting exercises. Furthermore, deposition within the channel has occurred in multiple locations coincident in time with accelerated sediment production following European settlement. Generally, this has occurred on a subset of the features we have examined here, namely linear bench features low in the channel. This suggests that accelerated aggradation on in-channel depositional surfaces has been in part a response to accelerated erosion within the catchment. The entire contribution of ~ 370 kilotonnes per annum of fine sediment estimated to have been produced by alluvial gully erosion over the last ~ 100 years can be accounted for by that stored as in-channel alluvium. These features therefore can play an important role in mitigating the impact on the receiving water of accelerated erosion.

  18. Long-Term Impact of Sediment Deposition and Erosion on Water Surface Profiles in the Ner River

    Directory of Open Access Journals (Sweden)

    Tomasz Dysarz

    2017-02-01

    Full Text Available The purpose of the paper is to test forecasting of the sediment transport process, taking into account two main uncertainties involved in sediment transport modeling. These are: the lack of knowledge regarding future flows, and the uncertainty with respect to which sediment transport formula should be chosen for simulations. The river reach chosen for study is the outlet part of the Ner River, located in the central part of Poland. The main characteristic of the river is the presence of an intensive morphodynamic process, increasing flooding frequency. The approach proposed here is based on simulations with a sediment-routing model and assessment of the hydraulic condition changes on the basis of hydrodynamic calculations for the chosen characteristic flows. The data used include Digital Terrain Models (DTMs, cross-section measurements, and hydrological observations from the Dabie gauge station. The sediment and hydrodynamic calculations are performed using program HEC-RAS 5.0. Twenty inflow scenarios are of a 10-year duration and are composed on the basis of historical data. Meyer-Peter and Müller and Engelund-Hansen formulae are applied for the calculation of sediment transport intensity. The methodology presented here seems to be a good tool for the prediction of long-term impacts on water surface profiles caused by sediment deposition and erosion.

  19. Development, evaluation, and application of sediment quality targets for assessing and managing contaminated sediments in Tampa Bay, Florida

    Science.gov (United States)

    MacDonald, D.D.; Carr, R.S.; Eckenrod, D.; Greening, H.; Grabe, S.; Ingersoll, C.G.; Janicki, S.; Janicki, T.; Lindskoog, R.A.; Long, E.R.; Pribble, R.; Sloane, G.; Smorong, D.E.

    2004-01-01

    Tampa Bay is a large, urban estuary that is located in west central Florida. Although water quality conditions represent an important concern in this estuary, information from numerous sources indicates that sediment contamination also has the potential to adversely affect aquatic organisms, aquatic-dependent wildlife, and human health. As such, protecting relatively uncontaminated areas of the bay from contamination and reducing the amount of toxic chemicals in contaminated sediments have been identified as high-priority sediment management objectives for Tampa Bay. To address concerns related to sediment contamination in the bay, an ecosystem-based framework for assessing and managing sediment quality conditions was developed that included identification of sediment quality issues and concerns, development of ecosystem goals and objectives, selection of ecosystem health indicators, establishment of metrics and targets for key indicators, and incorporation of key indicators, metrics, and targets into watershed management plans and decision-making processes. This paper describes the process that was used to select and evaluate numerical sediment quality targets (SQTs) for assessing and managing contaminated sediments. These SQTs included measures of sediment chemistry, whole-sediment and pore-water toxicity, and benthic invertebrate community structure. In addition, the paper describes how the SQTs were used to develop site-specific concentration-response models that describe how the frequency of adverse biological effects changes with increasing concentrations of chemicals of potential concern. Finally, a key application of the SQTs for defining sediment management areas is discussed.

  20. Trends in historical mercury deposition inferred from lake sediment cores across a climate gradient in the Canadian High Arctic.

    Science.gov (United States)

    Korosi, Jennifer B; Griffiths, Katherine; Smol, John P; Blais, Jules M

    2018-06-02

    Recent climate change may be enhancing mercury fluxes to Arctic lake sediments, confounding the use of sediment cores to reconstruct histories of atmospheric deposition. Assessing the independent effects of climate warming on mercury sequestration is challenging due to temporal overlap between warming temperatures and increased long-range transport of atmospheric mercury following the Industrial Revolution. We address this challenge by examining mercury trends in short cores (the last several hundred years) from eight lakes centered on Cape Herschel (Canadian High Arctic) that span a gradient in microclimates, including two lakes that have not yet been significantly altered by climate warming due to continued ice cover. Previous research on subfossil diatoms and inferred primary production indicated the timing of limnological responses to climate warming, which, due to prevailing ice cover conditions, varied from ∼1850 to ∼1990 for lakes that have undergone changes. We show that climate warming may have enhanced mercury deposition to lake sediments in one lake (Moraine Pond), while another (West Lake) showed a strong signal of post-industrial mercury enrichment without any corresponding limnological changes associated with warming. Our results provide insights into the role of climate warming and organic carbon cycling as drivers of mercury deposition to Arctic lake sediments. Copyright © 2018 Elsevier Ltd. All rights reserved.

  1. Response of PAH-degrading genes to PAH bioavailability in the overlying water, suspended sediment, and deposited sediment of the Yangtze River.

    Science.gov (United States)

    Xia, Xinghui; Xia, Na; Lai, Yunjia; Dong, Jianwei; Zhao, Pujun; Zhu, Baotong; Li, Zhihuang; Ye, Wan; Yuan, Yue; Huang, Junxiong

    2015-06-01

    The degrading genes of hydrophobic organic compounds (HOCs) serve as indicators of in situ HOC degradation potential, and the existing forms and bioavailability of HOCs might influence the distribution of HOC-degrading genes in natural waters. However, little research has been conducted to study the relationship between them. In the present study, nahAc and nidA genes, which act as biomarkers for naphthalene- and pyrene-degrading bacteria, were selected as model genotypes to investigate the response of polycyclic aromatic hydrocarbon (PAH)-degrading genes to PAH bioavailability in the overlying water, suspended sediment (SPS), and deposited sediment of the Yangtze River. The freely dissolved concentration, typically used to reflect HOC bioavailability, and total dissolved, as well as sorbed concentrations of PAHs were determined. Phylogenetic analysis showed that all the PAH-ring hydroxylating dioxygenase gene sequences of Gram-negative bacteria (PAH-RHD[GN]) were closely related to nahAc, nagAc, nidA, and uncultured PAH-RHD genes. The PAH-RHD[GN] gene diversity as well as nahAc and nidA gene copy numbers decreased in the following order: deposited sediment>SPS>overlying water. The nahAc and nidA gene abundance was not significantly correlated with environmental parameters but was significantly correlated with the bioavailable existing forms of naphthalene and pyrene in the three phases. The nahAc gene copy numbers in the overlying water and deposited sediment were positively correlated with freely dissolved naphthalene concentrations in the overlying and pore water phases, respectively, and so were nidA gene copy numbers. This study suggests that the distribution and abundance of HOC-degrading bacterial population depend on the HOC bioavailability in aquatic environments. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. On the effect of cross sectional shape on incipient motion and deposition of sediments in fixed bed channels

    Directory of Open Access Journals (Sweden)

    Safari Mir-Jafar-Sadegh

    2014-03-01

    Full Text Available The condition of incipient motion and deposition are of the essential issues for the study of sediment transport. This phenomenon is of great importance to hydraulic engineers for designing sewers, drainage, as well as other rigid boundary channels. This is a study carried out with the objectives of describing the effect of cross-sectional shape on incipient motion and deposition of particles in rigid boundary channels. In this research work, the experimental data given by Loveless (1992 and Mohammadi (2005 are used. On the basis of the critical velocity approach, a new incipient motion equation for a V-shaped bottom channel and incipient deposition of sediment particles equations for rigid boundary channels having circular, rectangular, and U-shaped cross sections are obtained. New equations were compared to the other incipient motion equations. The result shows that the cross-sectional shape is an important factor for defining the minimum velocity for no-deposit particles. This study also distinguishes incipient motion of particles from incipient deposition for particles. The results may be useful for designing fixed bed channels with a limited deposition condition.

  3. Sediment and carbon deposition vary among vegetation assemblages in a coastal salt marsh

    Directory of Open Access Journals (Sweden)

    J. J. Kelleway

    2017-08-01

    Full Text Available Coastal salt marshes are dynamic, intertidal ecosystems that are increasingly being recognised for their contributions to ecosystem services, including carbon (C accumulation and storage. The survival of salt marshes and their capacity to store C under rising sea levels, however, is partially reliant upon sedimentation rates and influenced by a combination of physical and biological factors. In this study, we use several complementary methods to assess short-term (days deposition and medium-term (months accretion dynamics within a single marsh that contains three salt marsh vegetation types common throughout southeastern (SE Australia.We found that surface accretion varies among vegetation assemblages, with medium-term (19 months bulk accretion rates in the upper marsh rush (Juncus assemblage (1.74 ± 0.13 mm yr−1 consistently in excess of estimated local sea-level rise (1.15 mm yr−1. Accretion rates were lower and less consistent in both the succulent (Sarcocornia, 0.78 ± 0.18 mm yr−1 and grass (Sporobolus, 0.88 ± 0.22 mm yr−1 assemblages located lower in the tidal frame. Short-term (6 days experiments showed deposition within Juncus plots to be dominated by autochthonous organic inputs with C deposition rates ranging from 1.14 ± 0.41 mg C cm−2 d−1 (neap tidal period to 2.37 ± 0.44 mg C cm−2 d−1 (spring tidal period, while minerogenic inputs and lower C deposition dominated Sarcocornia (0.10 ± 0.02 to 0.62 ± 0.08 mg C cm−2 d−1 and Sporobolus (0.17 ± 0.04 to 0.40 ± 0.07 mg C cm−2 d−1 assemblages.Elemental (C : N, isotopic (δ13C, mid-infrared (MIR and 13C nuclear magnetic resonance (NMR analyses revealed little difference in either the source or character of materials being deposited among neap versus spring tidal periods. Instead, these analyses point to substantial redistribution of materials within the Sarcocornia and

  4. Origin and depositional environment of fine-grained sediments since the last glacial maximum in the southeastern Yellow Sea: evidence from rare earth elements

    Science.gov (United States)

    Um, In Kwon; Choi, Man Sik; Lee, Gwang Soo; Chang, Tae Soo

    2015-12-01

    Despite the well-reconstructed seismic stratigraphy of the Holocene mud deposit in the southeastern Yellow Sea, known as the Heuksan mud belt (HMB), the provenances of these sediments and their depositional environments are unclear, especially for the fine-grained sediments. According to seismic data (extracted from another article in this special issue), the HMB comprises several sedimentary units deposited since the last glacial maximum. Based on analytical results on rare earth elements, fine-grained sediments in all sedimentary units can be interpreted as mixtures of sediments discharged from Chinese and Korean rivers. The proportions of fine-grained sediments from Chinese rivers (74.5 to 80.0%) were constant and higher than those from Korean rivers in all units. This fact demonstrates that all units have the same fine-grained sediment provenance: units III-b and III-a, located in the middle and northern parts of the HMB and directly deposited from Chinese rivers during the sea-level lowstand, could be the sediment source for units II-b and II-a. Unit I, while ambiguous, is of mixed origin combining reworked sediments from nearby mud deposits and Changjiang River-borne material with those of the Keum River. The results of this study indicate that at least 18.6% of bulk sediments in the HMB clearly originate from Chinese rivers, despite its location close to the southwestern coast of Korea.

  5. ASSESSMENT OF THE CHEMICAL POLLUTION OF THE SOIL, GROUND AND BOTTOM SEDIMENTS AT KLEN GOLD AND SILVER DEPOSIT

    Directory of Open Access Journals (Sweden)

    Bryukhan' Fedor Fedorovich

    2012-10-01

    Full Text Available Currently, prospecting and design-related works are performed prior to the upcoming launch of mining operations at Klen gold and silver deposit in Chukot Autonomous District. The anthropogenic impact of the geological exploration in this intact territory has been produced since 1984. A considerable amount of borehole drilling, prospecting, road building, and temporary housing development has been performed. The engineering research, including ecological surveys, has been completed to assess the ecological impact of upcoming exploratory and mining operations at the deposit. Assessment of the geochemical condition of the landscape constituents, including the soil, ground and bottom sediments is of special importance in terms of their engineering protection and rational management of the natural environment. The above assessments were based on the field sampling made by «Sibgeoconsulting», CJSC (Krasnoyarsk and the laboratory research made by accredited laboratories of Federal State Unitary Geological Enterprise «Urangeolograzvedka» (Irkutsk and «Krasnoyarskgeologiya» (Krasnoyarsk. The analysis of the chemical pollution of soils, ground and bottom sediments is based on the examination of 30 samples. Peculiarities of the chemical composition of samples extracted at the deposit were identified. It has been discovered that pH values of the soil vary from 5.1 to 7.3. The concentration of metal in bottom sediments exceeds its concentration in the soil by far. Almost all irregular features of the sample water in the whole territory of the deposit are caused by the anthropogenic impact. In general, the metal content in soils, ground and bottom sediments within the territory of the deposit is slightly different from the regular clarke.

  6. Legacy sediment, lead, and zinc storage in channel and floodplain deposits of the Big River, Old Lead Belt Mining District, Missouri, USA

    Science.gov (United States)

    Pavlowsky, Robert T.; Lecce, Scott A.; Owen, Marc R.; Martin, Derek J.

    2017-12-01

    deposits. Most of the metal mass in channel deposits is stored near the mines, with 72% of the Pb and 78% of the Zn occurring in the 25 km of channel proximal to the mine source. Although environmental assessments of streams contaminated by mines often focus on evaluating metal concentrations in the geochemically active fine sediment fractions, about 60% of the Pb stored in channels is associated with coarse dolomite tailings fragments deposited in channels within 25 km of the mines. The magnitude and basinwide distribution of Pb and Zn storage in legacy floodplain sediments ensures that remobilization by bank erosion will be a continuing problem for water quality far into the future.

  7. Characterization of heavy metal desorption from road-deposited sediment under acid rain scenarios.

    Science.gov (United States)

    Zhao, Bo; Liu, An; Wu, Guangxue; Li, Dunzhu; Guan, Yuntao

    2017-01-01

    Road-deposited sediments (RDS) on urban impervious surfaces are important carriers of heavy metals. Dissolved heavy metals that come from RDS influenced by acid rain, are more harmful to urban receiving water than particulate parts. RDS and its associated heavy metals were investigated at typical functional areas, including industrial, commercial and residential sites, in Guangdong, Southern China, which was an acid rain sensitive area. Total and dissolved heavy metals in five particle size fractions were analyzed using a shaking method under acid rain scenarios. Investigated heavy metals showed no difference in the proportion of dissolved fraction in the solution under different acid rain pHs above 3.0, regardless of land use. Dissolved loading of heavy metals related to organic carbon content were different in runoff from main traffic roads of three land use types. Coarse particles (>150μm) that could be efficiently removed by conventional street sweepers, accounted for 55.1%-47.1% of the total dissolved metal loading in runoff with pH3.0-5.6. The obtained findings provided a significant scientific basis to understand heavy metal release and influence of RDS grain-size distribution and land use in dissolved heavy metal pollution affected by acid rain. Copyright © 2016. Published by Elsevier B.V.

  8. Metalliferous sediment and a silica-hematite deposit within the Blanco fracture zone, Northeast Pacific

    Science.gov (United States)

    Hein, J.R.; Clague, D.A.; Koski, R.A.; Embley, R.W.; Dunham, R.E.

    2008-01-01

    A Tiburon ROV dive within the East Blanco Depression (EBD) increased the mapped extent of a known hydrothermal field by an order of magnitude. In addition, a unique opal-CT (cristobalite-tridymite)-hematite mound was discovered, and mineralized sediments and rock were collected and analyzed. Silica-hematite mounds have not previously been found on the deep ocean floor. The light-weight rock of the porous mound consists predominantly of opal-CT and hematite filaments, rods, and strands, and averages 77.8% SiO2 and 11.8% Fe2O3. The hematite and opal-CT precipitated from a low-temperature (???115?? C), strongly oxidized, silica- and iron-rich, sulfur-poor hydrothermal fluid; a bacterial mat provided the framework for precipitation. Samples collected from a volcaniclastic rock outcrop consist primarily of quartz with lesser plagioclase, smectite, pyroxene, and sulfides; SiO2 content averages 72.5%. Formation of these quartz-rich samples is best explained by cooling in an up-flow zone of silica-rich hydrothermal fluids within a low permeability system. Opal-A, opal-CT, and quartz mineralization found in different places within the EBD hydrothermal field likely reflects decreasing silica saturation and increasing temperature of the mineralizing fluid with increasing silica crystallinity. Six push cores recovered gravel, coarse sand, and mud mineralized variously by Fe or Mn oxides, silica, and sulfides. Total rare-earth element concentrations are low for both the rock and push core samples. Ce and Eu anomalies reflect high and low temperature hydrothermal components and detrital phases. A remarkable variety of types of mineralization occur within the EBD field, yet a consistent suite of elements is enriched (relative to basalt and unmineralized cores) in all samples analyzed: Ag, Au, S, Mo, Hg, As, Sb, Sr, and U; most samples are also enriched in Cu, Pb, Cd, and Zn. On the basis of these element enrichments, the EBD hydrothermal field might best be described as a base

  9. The Deposition and Accumulation of Microplastics in Marine Sediments and Bottom Water from the Irish Continental Shelf.

    Science.gov (United States)

    Martin, Jake; Lusher, Amy; Thompson, Richard C; Morley, Audrey

    2017-09-07

    Microplastics are widely dispersed throughout the marine environment. An understanding of the distribution and accumulation of this form of pollution is crucial for gauging environmental risk. Presented here is the first record of plastic contamination, in the 5 mm-250 μm size range, of Irish continental shelf sediments. Sixty-two microplastics were recovered from 10 of 11 stations using box cores. 97% of recovered microplastics were found to reside shallower than 2.5 cm sediment depth, with the area of highest microplastic concentration being the water-sediment interface and top 0.5 cm of sediments (66%). Microplastics were not found deeper than 3.5 ± 0.5 cm. These findings demonstrate that microplastic contamination is ubiquitous within superficial sediments and bottom water along the western Irish continental shelf. Results highlight that cores need to be at least 4-5 cm deep to quantify the standing stock of microplastics within marine sediments. All recovered microplastics were classified as secondary microplastics as they appear to be remnants of larger items; fibres being the principal form of microplastic pollution (85%), followed by broken fragments (15%). The range of polymer types, colours and physical forms recovered suggests a variety of sources. Further research is needed to understand the mechanisms influencing microplastic transport, deposition, resuspension and subsequent interactions with biota.

  10. Sedimentation

    Science.gov (United States)

    Cliff R. Hupp; Michael R. Schening

    2000-01-01

    Sedimentation is arguably the most important water-quality concern in the United States. Sediment trapping is cited frequently as a major function of riverine-forested wetlands, yet little is known about sedimcntation rates at the landscape scale in relation to site parameters, including woody vegetation type, elevation, velocity, and hydraulic connection to the river...

  11. Earthquake-induced soft-sediment deformation structures in Late Pleistocene lacustrine deposits of Issyk-Kul lake (Kyrgyzstan)

    Science.gov (United States)

    Gladkov, A. S.; Lobova, E. U.; Deev, E. V.; Korzhenkov, A. M.; Mazeika, J. V.; Abdieva, S. V.; Rogozhin, E. A.; Rodkin, M. V.; Fortuna, A. B.; Charimov, T. A.; Yudakhin, A. S.

    2016-10-01

    This paper discusses the composition and distribution of soft-sediment deformation structures induced by liquefaction in Late Pleistocene lacustrine terrace deposits on the southern shore of Issyk-Kul Lake in the northern Tien Shan mountains of Kyrgyzstan. The section contains seven deformed beds grouped in two intervals. Five deformed beds in the upper interval contain load structures (load casts and flame structures), convolute lamination, ball-and-pillow structures, folds and slumps. Deformation patterns indicate that a seismic trigger generated a multiple slump on a gentle slope. The dating of overlying subaerial deposits suggests correlation between the deformation features and strong earthquakes in the Late Pleistocene.

  12. Modelling post-depositional transport of PAHs in aquatic bed sediments using CoReTranS

    Energy Technology Data Exchange (ETDEWEB)

    Go, Jason [Imperial College London, London (United Kingdom). Dept. of Earth Science and Engineering; Stegemann, Julia A. [Imperial College London, London (United Kingdom). Dept. of Civil, Environmental and Geomatic Engineering

    2012-12-15

    Purpose: Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous and persistent contaminants in aquatic bed sediments. A better understanding of their in-bed fate and transport is therefore key in minimising the risk to the environment over time through various remediation and monitoring strategies. Since ecological effects and risks are related to contaminant concentrations, this study developed CoReTranS, a predictive model that simulates one-dimensional organic contaminant reaction and transport in bed sediments. Materials and methods: CoReTranS was benchmarked against analytical solutions of simplified reactive transport models and validated using a published study of marsh sediments contaminated with petroleum-derived hydrocarbons from Wild Harbour, West Falmouth, MA, USA. Results and discussion: The CoReTranS model effectively predicted the vertical distribution of PAHs in the Wild Harbour sediments as confirmed by the modelling results from the published study. The CoReTranS model was also used to interpret results from a published study of PAH-contaminated fjord sediments from Kitimat Arm in British Columbia, Canada. Specific insights into the post-depositional fate and transport of selected PAHs in the Kitimat fjord sediments were obtained by comparing the measured concentration-depth profiles with the numerical results from the CoReTranS model. Key parameters such as effective diffusivity of contaminants and burial velocities of sediment particles were shown to possibly account for the predicted concentrations-depth profiles in the Kitimat fjord sediments. Conclusions: As demonstrated, CoReTranS can simulate reactive transport models in order to predict PAH concentration profiles in porewater under site-specific conditions. The information derived from the use of the CoReTranS model highlighted practical application of such information by engineers to site-specific risk assessment and remediation. (orig.)

  13. Evaluation of older bay mud sediment from Richmond Harbor, California

    Energy Technology Data Exchange (ETDEWEB)

    Pinza, M.R.; Mayhew, H.L.; Word, J.Q.

    1996-09-01

    The older, bay mud (OBM) unit predates modem man and could act as a barrier to the downward transport of contaminants from the younger bay mud (YBM) because of its hard-packed consistency. However, its chemical and biological nature have not been well characterized. Battelle/Marine Sciences Laboratory (MSL) conducted three independent studies of OBM sediment in January 1993, January 1994, and October 1994. These studies evaluated potential chemical contamination and biological effects of OBM that could occur as a result of dredging and disposal activities. These evaluations were performed by conducting chemical analysis, solid-phase toxicity tests, suspended- particulate-phase (SPP) toxicity tests, and bioaccumulation tests on the OBM sediment. If the sediment chemistry and toxicity results showed no or minimal contamination and toxicological responses, then either the OBM could be left exposed in Richmond Harbor after dredging the YBM without leaving a source of contamination, or if the project depths necessitate, the OBM would be acceptable for disposal at an appropriate disposal site.

  14. Particle size distribution and characteristics of heavy metals in road-deposited sediments from Beijing Olympic Park.

    Science.gov (United States)

    Li, Haiyan; Shi, Anbang; Zhang, Xiaoran

    2015-06-01

    Due to rapid urbanization and industrialization, heavy metals in road-deposited sediments (RDSs) of parks are emitted into the terrestrial, atmospheric, and water environment, and have a severe impact on residents' and tourists' health. To identify the distribution and characteristic of heavy metals in RDS and to assess the road environmental quality in Chinese parks, samples were collected from Beijing Olympic Park in the present study. The results indicated that particles with small grain size (Pb>Cu>Zn. This study analyzed the mobility of heavy metals in sediments using partial sequential extraction with the Tessier procedure. The results revealed that the apparent mobility and potential metal bioavailability of heavy metals in the sediments, based on the exchangeable and carbonate fractions, decreased in the order: Cd>Zn≈Pb>Cu. Copyright © 2015. Published by Elsevier B.V.

  15. Effects of terrestrial and marine organic matters on deposition of dechlorane plus (DP) in marine sediments from the Southern Yellow Sea, China: Evidence from multiple biomarkers

    International Nuclear Information System (INIS)

    Wang, Guoguang; Peng, Jialin; Hao, Ting; Feng, Lijuan; Liu, Qiaoling; Li, Xianguo

    2017-01-01

    As an emerging halogenated organic contaminant, Dechlorane Plus (DP) was scarcely reported in marine environments, especially in China. In this work, 35 surface sediments and a sediment core were collected across the Southern Yellow Sea (SYS) to comprehensively explore the spatio-temporal distribution and possible migration pathway of DP. DP concentrations ranged from 14.3 to 245.5 pg/g dry weight in the surface sediments, displaying a seaward increasing trend with the high levels in the central mud zone. This spatial distribution pattern was ascribed to that fine particles with the elevated DP levels were preferentially transported to the central mud zone under hydrodynamic forcing and/or via long-range atmospheric transportation and deposition. DP concentrations in sediment core gradually increased from the mid-1950s to present, which corresponded well with the historical production and usage of DP, as well as the economic development in China. Significantly positive correlation between DP and total organic carbon (TOC) in both surface sediments and sediment core indicated TOC-dependent natural deposition of DP in the SYS. We used multiple biomarkers, for the first time, to explore the potential effects of terrestrial and marine organic matters (TOM and MOM) on DP deposition. The results showed that competition may occur between TOM and MOM for DP adsorption, and MOM was the predominant contributor in controlling DP deposition in the marine sediments from the SYS. - Highlights: • Effects of TOM and MOM on DP deposition were first explored by multi-biomarkers. • Hydrodynamic forcing and atmospheric deposition were responsible for DP in the SYS. • MOM was the predominant contributor in controlling DP deposition to sediments in the SYS. • Competition may occur between TOM and MOM for DP adsorption. - This study was the first attempt to comprehensively explore the effects of TOM and MOM on DP deposition in marine sediments from the SYS.

  16. Evaluating grass strips trapping efficiency of sediments and herbicides

    Science.gov (United States)

    Burguet, Maria; Guzmán, Gema; de Luna, Elena; Taguas, Encarnación V.; Gómez, José Alfonso

    2016-04-01

    Water erosion and associated offsite contamination are major environmental risks in many Mediterranean crops such as olives or vineyards (Beaufoy, 2001; Gómez et al., 2011). The use of cover crops has been prescribed as a mitigation measure for both problems because permanent cover crops have demonstrated to reduce sediment and agrochemical loads (e.g. Gómez, 2009a, b). However, large uncertainty remains about its effectiveness degree to reduce sediment and agrochemical contribution to streams due to the limited number of available studies, and the large variability observed under field conditions (Taguas et al., 2012). Furthermore, the determination of sediment and herbicide sources using suitable sediment tracing/fingerprinting properties has been noted as one tool to evaluate the effectiveness and functioning of vegetated filters at the catchment scale (Koiter et al., 2013). The objectives of the present study were twofold: [1] to explore the combined use of natural and simulated rainfall and magnetic iron oxide in understanding the performance of vegetation strips on runoff and soil and herbicide losses at plot scale and, [2] to evaluate the effectiveness degree of vegetation strips in buffering sediment and herbicide from bare soil areas under different conditions compared to a control situation with no strips. This study encompasses six rainfall simulations under four different soil managements combining the use of a magnetic iron oxide as a sediment tracer to obtain a better understanding of the vegetation strips trapping efficiency. Three runoff plots of 6 m × 14 m were established in a 20% hillslope under a Fluvisol alluvial terrace. Each of the plots contained three bare strips tagged with magnetic iron oxide and three strips with Lolium multiflorum L. The soil management simulated scenarios were: immediately after sowing the vegetation cover (June 2011cover crop), with settled vegetation cover (June 2012cover crop), after 5 cm of deep ploughing

  17. Isotopic data from proterozoic sediment-hosted sulfide deposits of Brazil: Implications for their metallogenic evolution and for mineral exploration

    International Nuclear Information System (INIS)

    Misi, Aroldo; Coelho, Carlos E.S.; Franca Rocha, Washington J.S.; Gomez, Adriana S.R.; Cunha, Iona A.; Iyer, Sundaram S.; Tassinari, Colombo C.G.; Kyle, J. Richard

    1998-01-01

    Geological, petrographic, fluid inclusions studies and isotopic data of seven Proterozoic sediment-hosted Pb-Zn-Ag sulfide deposits of Brazil, permit the estimation of the age of the hosting sequence and the mineralization, the nature of the sulfur and metal sources, the temperature range of sulfide formation and the environment of deposition of the mineral deposits. The studies suggest that they were formed during periods of extensional tectonics: Growth faults or reactivated basement faults were responsible for localized circulation of metal-bearing fluids within the sedimentary sequences. In most cases, sulfides were formed by the reduction of sedimentary sulfates. Linear structures are important controls for sulfide concentration in these Proterozoic basins. (author)

  18. From hydro-geomorphological mapping to sediment transfer evaluation in the Upper Guil Catchment (Queyras, French Alps)

    Science.gov (United States)

    Lissak, Candide; Fort, Monique; Arnaud-Fassetta, Gilles; Mathieu, Alexandre; Malet, Jean-Philippe; Carlier, Benoit; Betard, François; Cossart, Etienne; Madelin, Malika; Viel, Vincent; Charney, Bérengère; Bletterie, Xavier

    2014-05-01

    The Guil River catchment (Queyras, Southern French Alps) is prone to hydro-geomorphic hazards related to catastrophic floods, with an amplification of their impacts due to strong hillslope-channel connectivity such as in 1957 (> R.I. 100 yr), and more recently in 2000 (R.I. 30 yr). In both cases, the rainfall intensity, aggravated by pre-existing saturated soils, explained the immediate response of the fluvial system and the subsequent destabilisation of slopes. This resulted in serious damages to infrastructure and buildings in the valley bottom, mostly along some specific reaches and confluences with debris flow prone tributaries. After each event, new protective structures are built. One of the purposes of this study, undertaken in the frame of the SAMCO (ANR) project, was to understand the hydro-geomorphological functioning of this upper Alpine catchment in a context of hazards mitigation and sustainable management of sediment yield, transfer and deposition. To determine the main sediment storages that could be mobilised during the next major hydro-meteorological events, the first step of our study consists in the identification and characterisation of areas that play a role into the sediment transfer processing. From environmental characteristics (channel geometric, vegetation cover…) and anthropogenic factors (hydraulic infrastructures, urban development…), a semi-automatic method provides a typology of contribution areas with sediment storages sensitive to erosion, or areas that will be prone to deposition of sediments during the next flooding event. The second step of the study is focused on the sediment storages with their characterisation and connectivity to the trunk channel. Taking into account the entire catchment and including the torrential system, this phase analyses the sedimentary transfers from the identification and classification of sediment storages to the evaluation of the degree of connectivity with the main or secondary channels. The

  19. Short-term assessment of the sediment deposition rate and water conditions during a rainy season on La Azufrada coral reef, Gorgona Island, Colombia

    KAUST Repository

    Lozano-Corté s, Diego F; Giraldo, Alan; Izquierdo, Vanessa

    2014-01-01

    .60±0.52, respectively. Fourteen taxonomic groups of invertebrates were detected inside the sediment traps with bivalves and copepods being the most abundant and frequen. The findings presented here constitute the first report of both the potential sediment deposition

  20. Textural characteristics and sedimentary environment of sediment at eroded and deposited regions in the severely eroded coastline of Batu Pahat, Malaysia.

    Science.gov (United States)

    Wan Mohtar, Wan Hanna Melini; Nawang, Siti Aminah Bassa; Abdul Maulud, Khairul Nizam; Benson, Yannie Anak; Azhary, Wan Ahmad Hafiz Wan Mohamed

    2017-11-15

    This study investigates the textural characteristics of sediments collected at eroded and deposited areas of highly severed eroded coastline of Batu Pahat, Malaysia. Samples were taken from systematically selected 23 locations along the 67km stretch of coastline and are extended to the fluvial sediments of the main river of Batu Pahat. Grain size distribution analysis was conducted to identify its textural characteristics and associated sedimentary transport behaviours. Sediments obtained along the coastline were fine-grained material with averaged mean size of 7.25 ϕ, poorly sorted, positively skewed and has wide distributions. Samples from eroded and deposition regions displayed no distinctive characteristics and exhibited similar profiles. The high energy condition transported the sediments as suspension, mostly as pelagic and the sediments were deposited as shallow marine and agitated deposits. The fluvial sediments of up to 3km into the river have particularly similar profile of textural characteristics with the neighbouring marine sediments from the river mouth. Profiles were similar with marine sediments about 3km opposite the main current and can go up to 10km along the current of Malacca Straits. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Transport and deposition of plutonium in the ocean: Evidence from Gulf of Mexico sediments

    International Nuclear Information System (INIS)

    Scott, M.R.; Salter, P.F.; Halverson, J.E.

    1983-01-01

    A study of sediments in the Gulf of Mexico shows dramatic gradients in Pu content and isotope ratios from the continental shelf to the Sigsbee Abyssal Plain. In terms of predicted direct fallout inventory of Pu, one shelf core contains 745% of the predicted inventory, while abyssal plain sediments contain only 15-20% of the predicted value. Absolute Pu concentrations of shelf sediments are also conspicuously high, up to 110 dpm/kg, compared to 13.5 dpm/kg in Mississippi River suspended sediment. There is no evidence of Pu remobilization in Gulf of Mexico shelf sediments, based on comparison of Pu profiles with Mn/Al and Fe/Al profiles. Horizontal transport of fallout nuclides from the open ocean to removal sites in ocean margin sediments is concluded to be the source of both the high concentrations and high inventories of Pu reported here. The shelf sediments show 240 Pu/ 239 Pu ratios close to 0.179, the average stratospheric fallout value, but the ratios decrease progressively across the Gulf to low values of 0.06 in abyssal plain sediments. The source of low-ratio Pu in deep-water sediments may be debris from low yield tests transported in the troposphere. Alternatively, it may represent a fraction of the Pu from global stratospheric fallout which has been separated in the water column from the remainder of the Pu in the ocean. In either case, the low-ratio material must have been removed rapidly to the sea floor where it composes a major fraction of the Pu in abyssal plain sediments. Pu delivered by global atmospheric fallout from the stratosphere has apparently remained for the most part in the water or has been transported horizontally and removed into shallow-water sediments. (orig.)

  2. Turbidity current hydraulics and sediment deposition in erodible sinuous channels: Laboratory experiments and numerical simulations

    NARCIS (Netherlands)

    Janocko, M.; Cartigny, M.J.B.; Nemec, W.; Hansen, E.W.M.

    2013-01-01

    This study explores the relationship between the hydraulics of turbidity currents in erodible sinuous channels and the resulting intra-channel sediment depocentres (channel bars). Four factors are considered to exert critical control on sedimentation in sinuous submarine channels: (1) the

  3. Geologic characteristics of sediment- and volcanic-hosted disseminated gold deposits - Search for an occurrence model

    Science.gov (United States)

    White, Donald E.; Fournier, Robert O.; Rytuba, James J.; Rye, Robert O.; Cunningham, Charles G.; Berger, Byron R.; Silberman, Miles L.; Bonham, Harold F.; Strachan, Donald G.; Birak, Donald J.; Hawkins, Robert J.; Tooker, Edwin W.; Tooker, Edwin W.

    1985-01-01

    The current expansion of resource information, particularly on "disseminated" gold, and the improved technologies now available for resource investigations should place us in an enhanced position for developing a better predictive methodology for meeting one of the important responsibilities of the U.S. Geological Survey-to examine and assess the mineral resources of the geologic terranes composing the public (and privately owned) lands of the United States. The first step is systematic organization of these data. Geologic-occurrence models are an effective systematic method by which to organize large amounts of resource information into a logical sequence facilitating its use more effectively in meeting several industry and Survey objectives, which include the exploration for resources and the assessment of resource potential for land-use decisions. Such models also provide a scientific basis for metallogenesis research, which considers the observable features or attributes of ore occurrence and their "fit" into the Earth's resource puzzle. The use of models in making resource assessments/appraisals was addressed by Shawe (1981), who reported the results of a workshop on methods for resource appraisal of Wilderness and Conterminous United States Mineral Appraisal Program (CUSMAP; 1:250,000-scale quadrangles) areas. The Survey's main objective in the 1982 workshop was to evaluate the status of knowledge about disseminated or very fine grained gold deposits and, if possible, to develop an occurrence model(s).This report on the workshop proceedings has three main objectives: (1) Education through the publication of a summary review and presentation of new thinking and observations about the scientific bases for those geologic processes and environments that foster disseminated gold-ore formation; (2) systematic organization of available geologic, geochemical, and geophysical information for a range of typical disseminated gold deposits (including recognition of gaps

  4. An example of economical evaluation of stratiform uranium ore deposit

    International Nuclear Information System (INIS)

    Miyata, Hatsuho; Tabuchi, Akihiro; Ushijima, Kenichi.

    1992-01-01

    The Power Reactor and Nuclear Fuel Development corp. has carried out the business of uranium resource investigation and exploration in foreign countries aiming at securing uranium resources. If there is the possibility of economically developing the discovered uranium deposit, it is transferred to a Japanese private enterprise. In this paper, among the economical evaluation works that were carried out for the uranium deposits discovered by the Corp., the example of the initial economical evaluation for a stratiform uranium deposit carried out recently is reported. The deposit is located at the depth of 50 m - 70 m, and is a stratiform deposit having the extension of 4000 m x 1000 m. The boring investigation of about 350 holes was carried out for it. The estimation of the amount of uranium was done, and the production plan was made considering the scale of production, the characteristics of the ore, the circumstances of the site and so on. Based on the production plan, the initial expenses and the operation expenses were calculated. The design of the optimal pit which affects most the profitability and the economical evaluation were carried out. (K.I.)

  5. Observations on sediment sources in the Lower Athabasca River basin: implications of natural hydrocarbons inputs from oil sands deposits

    International Nuclear Information System (INIS)

    Conly, F.M.

    1999-01-01

    Government, industry and public concern exists over the environmental consequences of the development of the oil sand deposits in the McMurray Formation in the lower Athabasca River basin, Alberta. The impact of this development is unclear and is undergoing investigation. Investigations to date have focussed on the nature of the effluent produced by the extraction industry and its effect on biotic systems, and on the spatial distribution of hydrocarbon contaminants associated with deposited fluvial sediments. Natural hydrocarbon outcrops may be responsible for observed biomarker responses in areas not exposed to industrial effluent. Given this source of hydrocarbons and doubt concerning its environmental impact, it is difficult to ascertain the impact of oil extraction activities within a fluvial system. A study was conducted to determine the nature and extent of natural hydrocarbon releases within the context of the sediment regime of the lower Athabasca River basin. A description is included of observations from the field and a context is set up for assessing sediment-bound hydrocarbon contaminants in the lower Athabasca River basin. Abstract only included

  6. Uniqueness Deposit of Sediment on Floodplain Resulting From Lateral Accretion on Tropical Area : Study Case at Kampar River, Indonesia

    Directory of Open Access Journals (Sweden)

    Yuniarti Yuskar

    2017-03-01

    Full Text Available Kampar rivers has a length of 413 km with average depth of 7.7 m and width of 143 m. Sixty percent of  this rivers are meandering fluvial system which transport and deposit a mixture of suspended and bed-load (mixed load along low energy. River channel that moving sideways by erosion is undergoing lateral migration and the top of the point bar becomes the edge of the floodplain and the fining-upward succession of the point bar will be capped by overbank deposits of Kampar River. Along the Kampar Rivers, there are more than 60% of floodplain sediments and almost all of the floodplain formed by bend migration on the suspended-load channels of Kampar watershed. This formation consist of succession of fine to medium sand and silt/mud, with root traces, that form as drapes on the prograding bank. These beds dip mostly channel wards and quickly wedge out as they grade up and onto the floodplain. The depositional model is presented showing how lateral accretion can make a significant contribution to the preservation of fine-grained within channel deposits in contemporary floodplains. The examples presented here demonstrate that analogues to ancient point-bar deposits containing alternating sandstone and shale sequences are common in the low-energy fluvial environments of Riau rivers especially Kampar rivers.

  7. Economic evaluation of coal deposits. Ekonomicheskaya otsenka ugolinykh mestorozhdenii

    Energy Technology Data Exchange (ETDEWEB)

    Raikhel' , B L

    1979-01-01

    A presentation is made of theoretical problems, methods, and criteria for the economic evaluation of coal deposits. An examination is made of factors which influence the formation of magnitudes that are utilized in economic evaluations as well as problems whose solution requires the consideration of the economic evaluation of coal deposits (evaluation of useful mineral losses, substantiation for the extraction of reserves under various conditions, sectioning off reserves to an operating mine, the completeness of reserve extraction, and technico-economic substantiation for quality). Extensive experience in planning is summarized and data are illustrated by examples. The book is intended for engineering-technical personnel of enterprises, organizations, planning, and scientific-research institutes of the coal industry as well as geological organizations. 29 references, 27 tables.

  8. Dynamic transition of chemolithotrophic sulfur-oxidizing bacteria in response to amendment with nitrate in deposited marine sediments

    Directory of Open Access Journals (Sweden)

    Tomo eAoyagi

    2015-05-01

    Full Text Available Although environmental stimuli are known to affect the structure and function of microbial communities, their impact on the metabolic network of microorganisms has not been well investigated. Here, geochemical analyses, high-throughput sequencing of 16S rRNA genes and transcripts, and isolation of potentially relevant bacteria were carried out to elucidate the anaerobic respiration processes stimulated by nitrate (20 mM amendment of marine sediments. Marine sediments deposited by the Great East Japan Earthquake in 2011 were incubated anaerobically in the dark at 25°C for 5 days. Nitrate in slurry water decreased gradually for 2 days, then more rapidly until its complete depletion at day 5; production of N2O followed the same pattern. From day 2 to 5, the sulfate concentration increased and the sulfur content in solid-phase sediments significantly decreased. These results indicated that denitrification and sulfur oxidation occurred simultaneously. Illumina sequencing revealed the proliferation of known sulfur oxidizers, i.e., Sulfurimonas spp. and Chromatiales bacteria, which accounted for approximately 43.5% and 14.8% of the total population at day 5, respectively. They also expressed 16S rRNA to a considerable extent, whereas the other microorganisms, e.g., iron(III reducers and methanogens, became metabolically active at the end of the incubation. Extinction dilution culture in a basal-salts medium supplemented with sulfur compounds and nitrate successfully isolated the predominant sulfur oxidizers: Sulfurimonas sp. strain HDS01 and Thioalkalispira sp. strain HDS22. Their 16S rRNA genes showed 95.2−96.7% sequence similarity to the closest cultured relatives and they grew chemolithotrophically on nitrate and sulfur. Novel sulfur-oxidizing bacteria were thus directly involved in carbon fixation under nitrate-reducing conditions, activating anaerobic respiration processes and the reorganization of microbial communities in the deposited marine

  9. Do benthic sediment characteristics explain the distribution of juveniles of the deposit-feeding sea cucumber Australostichopus mollis?

    Science.gov (United States)

    Slater, Matthew J.; Jeffs, Andrew G.

    2010-10-01

    Despite the economic importance of many deposit-feeding sea cucumbers, the ecology of their juveniles is poorly understood and factors influencing juvenile habitat selection remain largely unexplained. We investigated the importance of the characteristics of the available sediment in determining the highly localised distribution of juveniles of the deposit-feeding Australasian sea cucumber Australostichopus mollis. Wild-caught juveniles were displaced to non-juvenile habitats with surface sediments characterised by lower total organic content (TOM) and nitrogen content, higher chlorophyll- a content and coarser grain size profiles compared to juvenile sites. The growth of displaced individual animals was monitored over 9 months and compared to control animals caged in the juvenile habitats. Displaced juvenile sea cucumbers had high survival rates that did not differ significantly from juvenile habitats. Displaced juveniles exhibited significantly higher specific growth rate (SGR) than those at juvenile sites ( p < 0.001), although the growth of individuals was highly variable within individual cages and among sites. The lower TOM and nitrogen content, and coarser grain size profiles at non-juvenile sites did not result in reductions in juvenile survival or growth. Higher microphytobenthic activity may have resulted in the higher growth rates observed at shallow non-juvenile sites. The SGR of juveniles over the first 6 months of the experiment ranged between 0.45% d - 1 and 0.74% d - 1 for all sites. This was followed by marked growth limitation between 6 and 9 months either as a result of increasing juvenile biomass in cages or seasonal growth limitation. A subsequent reduction in juvenile density resulted in markedly increased growth over the following 3 month period. Juvenile A. mollis show an ability to exploit a variety of benthic sediment food sources, indicating that their highly localised distribution is not due to differences in the food quality of

  10. Sediment depositional environment in some bays in Central west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Rajamanickam, G.V.; Gujar, A.R.

    negatively and Ratnagiri Bay positively skewed. Kalbadevi sediments show high kurtosis values while those of Mirya Bay show medium and Ratnagiri Bay low values. Bivariant plots between various textural parameters predict mixed environments, viz. for Kalbadevi...

  11. Depositional environment, organic matter characterization and hydrocarbon potential of Middle Miocene sediments from northeastern Bulgaria (Varna-Balchik Depression

    Directory of Open Access Journals (Sweden)

    Zdravkov Alexander

    2015-10-01

    Full Text Available The depositional environments and hydrocarbon potential of the siliciclastic, clayey and carbonate sediments from the Middle Miocene succession in the Varna-Balchik Depression, located in the south-eastern parts of the Moesian Platform, were studied using core and outcrop samples. Based on the lithology and resistivity log the succession is subdivided from base to top into five units. Siliciclastic sedimentation prevailed in the lower parts of units I and II, whereas their upper parts are dominated by carbonate rocks. Unit III is represented by laminated clays and biodetritic limestone. Units IV and V are represented by aragonitic sediments and biomicritic limestones, correlated with the Upper Miocene Topola and Karvuna Formations, respectively. Biogenic silica in the form of diatom frustules and sponge spicules correlates subunit IIa and unit III to the lower and upper parts of the Middle Miocene Euxinograd Formation. Both (subunits contain organic carbon contents in the order of 1 to 2 wt. % (median: 0.8 for subunit IIa; 1.3 for unit III, locally up to 4 wt. %. Based on Hydrogen Index values (HI and alkane distribution pattern, the kerogen is mainly type II in subunit IIa (average HI= 324 mg HC/g TOC and type III in unit III (average HI ~200 mg HC/g TOC. TOC and Rock Eval data show that subunit IIa holds a fair (to good hydrocarbon generative potential for oil, whereas the upper 5 m of unit III holds a good (to fair potential with the possibility to generate gas and minor oil. The rocks of both units are immature in the study area. Generally low sulphur contents are probably due to deposition in environments with reduced salinity. Normal marine conditions are suggested for unit III. Biomarker composition is typical for mixed marine and terrestrial organic matter and suggests deposition in dysoxic to anoxic environments.

  12. Uranium distribution and sandstone depositional environments: oligocene and upper Cretaceous sediments, Cheyenne basin, Colorado

    International Nuclear Information System (INIS)

    Nibbelink, K.A.; Ethridge, F.G.

    1984-01-01

    Wyoming-type roll-front uranium deposits occur in the Upper Cretaceous Laramie and Fox Hills sandstones in the Cheyenne basin of northeastern Colorado. The location, geometry, and trend of specific depositional environments of the Oligocene White River and the Upper Cretaceous Laramie and Fox Hills formations are important factors that control the distribution of uranium in these sandstones. The Fox Hills Sandstone consists of up to 450 ft (140 m) of nearshore marine wave-dominated delta and barrier island-tidal channel sandstones which overlie offshore deposits of the Pierre Shale and which are overlain by delta-plain and fluvial deposits of the Laramie Formation. Uranium, which probably originated from volcanic ash in the White River Formation, was transported by groundwater through the fluvial-channel deposits of the White River into the sandstones of the Laramie and Fox Hills formations where it was precipitated. Two favorable depositional settings for uranium mineralization in the Fox Hills Sandstone are: (1) the landward side of barrier-island deposits where barrier sandstones thin and interfinger with back-barrier organic mudstones, and (2) the intersection of barrier-island and tidal channel sandstones. In both settings, sandstones were probably reduced during early burial by diagenesis of contained and adjacent organic matter. The change in permeability trends between the depositional strike-oriented barrier sandstones and the dip-oriented tidal-channel sandstones provided sites for dispersed groundwater flow and, as demonstrated in similar settings in other depositional systems, sites for uranium mineralization

  13. [Distribution Characteristics and Pollution Status Evaluation of Sediments Nutrients in a Drinking Water Reservoir].

    Science.gov (United States)

    Huang, Ting-lin; Liu, Fei; Shi, Jian-chao

    2016-01-15

    The main purpose of this paper is to illustrate the influence of nutrients distribution in sediments on the eutrophication of drinking water reservoir. The sediments of three representative locations were field-sampled and analyzed in laboratory in March 2015. The distribution characteristics of TOC, TN and TP were measured, and the pollution status of sediments was evaluated by the comprehensive pollution index and the manual for sediment quality assessment. The content of TOC in sediments decreased with depth, and there was an increasing trend of the nitrogen content. The TP was enriched in surface sediment, implying the nutrients load in Zhoucun Reservoir was aggravating as the result of human activities. Regression analysis indicated that the content of TOC in sediments was positively correlated with contents of TN and TP in sediments. The TOC/TN values reflected that the vascular land plants, which contain cellulose, were the main source of organic matter in sediments. The comprehensive pollution index analysis result showed that the surface sediments in all three sampling sites were heavily polluted. The contents of TN and TP of surface sediments in three sampling sites were 3273-4870 mg x kg(-1) and 653-2969 mg x kg(-1), and the content of TOC was 45.65-83.00 mg x g(-1). According to the manual for sediment quality assessment, the TN, TP and TOC contents in sediments exceed the standard values for the lowest level of ecotoxicity, so there is a risk of eutrophication in Zhoucun Reservoir.

  14. Epigenetic-hydrothermal origin of the sediment-hosted Muellenbach uranium deposit, Baden-Baden, W-Germany

    International Nuclear Information System (INIS)

    Brockamp, O.; Zuther, M.; Clauer, N.

    1987-01-01

    Upper Carboniferous sediments on the margin of the northern Black Forest granite massif are the host rocks of the Muellenbach uranium deposit. According to K/Ar datings the sericites formed during the Jurassic (150 Ma), an age also interpreted from U/Pb ratios for the crystallization of the pitchblende. Based on vitrinite reflectance the mineralization temperature is estimated to be 240 0 -290 0 C. It is postulated that the hydrothermal solutions were supplied via deep-seated faults bordering and crosscutting the granite massif and the sedimentary trough which is an intramontane basin. In its immediate vicinity the rift valley of the Rhein graben developed. Uranium deposits in comparable settings are supposed to be predominately of epigenetic-hydrothermal origin. (orig./HP)

  15. Evaluating the importance of surface soil contributions to reservoir sediment in alpine environments: a combined modelling and fingerprinting approach in the Posets-Maladeta Natural Park

    Science.gov (United States)

    Palazón, L.; Gaspar, L.; Latorre, B.; Blake, W. H.; Navas, A.

    2014-09-01

    Soil in alpine environments plays a key role in the development of ecosystem services and in order to maintain and preserve this important resource, information is required on processes that lead to soil erosion. Similar to other mountain alpine environments, the Benasque catchment is characterised by temperatures below freezing that can last from November to April, intense rainfall events, typically in spring and autumn, and rugged topography which makes assessment of erosion challenging. Indirect approaches to soil erosion assessment, such as combined model approaches, offer an opportunity to evaluate soil erosion in such areas. In this study (i) the SWAT (Soil and Water Assessment Tool) hydrological and erosion model and (ii) sediment fingerprinting procedures were used in parallel to assess the viability of a combined modelling and tracing approach to evaluate soil erosion processes in the area of the Posets-Maladeta Natural Park (central Spanish Pyrenees). Soil erosion rates and sediment contribution of potential sediment sources defined by soil type (Kastanozems/Phaeozems; Fluvisols and Cambisols) were assessed. The SWAT model suggested that, with the highest specific sediment yields, Cambisols are the main source of sediment in the Benasque catchment and Phaeozems and Fluvisols were identified as the lowest sediment contributors. Spring and winter model runs gave the highest and lowest specific sediment yield, respectively. In contrast, sediment fingerprinting analysis identified Fluvisols, which dominate the riparian zone, as the main sediment source at the time of sampling. This indicates the importance of connectivity as well as potential differences in the source dynamic of material in storage versus that transported efficiently from the system at times of high flow. The combined approach enabled us to better understand soil erosion processes in the Benasque alpine catchment, wherein SWAT identified areas of potential high sediment yield in large flood

  16. Evaluation of recent sedimentation rates in Guajara Bay (N Brazilian coast) with 210Pb and 137Cs

    International Nuclear Information System (INIS)

    Ferreira, Paulo A.L.; Neves, Patricia A.; Figueira, Rubens C.L.

    2013-01-01

    In the last 50 years the Amazon region suffered the negative effects of urban growth and industrial and agricultural development. Belem, capital city of the state of Para located, is one of its greatest urban centers, and, within its influence, Guajara Bay receives wastes discharges from Belem, which introduce many organic and inorganic contaminants to this bay. As the environmental accumulation of these pollutants is deeply related to intensity and volume of sediments deposition, this study aims to evaluate recent sedimentation rates (in a time range of 60 years) in Guajara Bay. By using high resolution gamma spectrometry, a nuclear technique proper for the analysis of radionuclides 137 Cs and 210 Pb, recent sedimentation rates were assessed in three sediment cores collected in 2011. The mean sedimentation rates found were 0.85 ± 0.12 cm yr -1 for Anadim core, 1.02 ± 0.17 cm yr -1 for Outeiro core and 0.53 ± 0.04 cm yr -1 for Tucunduba core, which are within the range of expected values for systems such as bays, estuaries and lagoons with anthropic presence (the case of Guajara Bay). (author)

  17. Evaluation of recent sedimentation rates in Guajara Bay (N Brazilian coast) with {sup 210}Pb and {sup 137}Cs

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Paulo A.L.; Neves, Patricia A.; Figueira, Rubens C.L., E-mail: paulo.alves.ferreira@usp.br, E-mail: ticinev@yahoo.com.br, E-mail: rfigueira@usp.br [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Instituto Oceanografico

    2013-07-01

    In the last 50 years the Amazon region suffered the negative effects of urban growth and industrial and agricultural development. Belem, capital city of the state of Para located, is one of its greatest urban centers, and, within its influence, Guajara Bay receives wastes discharges from Belem, which introduce many organic and inorganic contaminants to this bay. As the environmental accumulation of these pollutants is deeply related to intensity and volume of sediments deposition, this study aims to evaluate recent sedimentation rates (in a time range of 60 years) in Guajara Bay. By using high resolution gamma spectrometry, a nuclear technique proper for the analysis of radionuclides {sup 137}Cs and {sup 210}Pb, recent sedimentation rates were assessed in three sediment cores collected in 2011. The mean sedimentation rates found were 0.85 ± 0.12 cm yr{sup -1}for Anadim core, 1.02 ± 0.17 cm yr{sup -1}for Outeiro core and 0.53 ± 0.04 cm yr{sup -1}for Tucunduba core, which are within the range of expected values for systems such as bays, estuaries and lagoons with anthropic presence (the case of Guajara Bay). (author)

  18. Transport and deposition of asbestos-rich sediment in the Sumas River, Whatcom County, Washington

    Science.gov (United States)

    Curran, Christopher A.; Anderson, Scott W.; Barbash, Jack E.; Magirl, Christopher S.; Cox, Stephen E.; Norton, Katherine K.; Gendaszek, Andrew S.; Spanjer, Andrew R.; Foreman, James R.

    2016-02-08

    Heavy sediment loads in the Sumas River of Whatcom County, Washington, increase seasonal turbidity and cause locally acute sedimentation. Most sediment in the Sumas River is derived from a deep-seated landslide of serpentinite that is located on Sumas Mountain and drained by Swift Creek, a tributary to the Sumas River. This mafic sediment contains high amounts of naturally occurring asbestiform chrysotile. A known human-health hazard, asbestiform chrysotile comprises 0.25–37 percent, by mass, of the total suspended sediment sampled from the Sumas River as part of this study, which included part of water year 2011 and all of water years 2012 and 2013. The suspended-sediment load in the Sumas River at South Pass Road, 0.6 kilometers (km) downstream of the confluence with Swift Creek, was 22,000 tonnes (t) in water year 2012 and 49,000 t in water year 2013. The suspended‑sediment load at Telegraph Road, 18.8 km downstream of the Swift Creek confluence, was 22,000 t in water year 2012 and 27,000 t in water year 2013. Although hydrologic conditions during the study were wetter than normal overall, the 2-year flood peak was only modestly exceeded in water years 2011 and 2013; runoff‑driven geomorphic disturbance to the watershed, which might have involved mass wasting from the landslide, seemed unexceptional. In water year 2012, flood peaks were modest, and the annual streamflow was normal. The fact that suspended-sediment loads in water year 2012 were equivalent at sites 0.6 and 18.8 km downstream of the sediment source indicates that the conservation of suspended‑sediment load can occur under normal hydrologic conditions. The substantial decrease in suspended-sediment load in the downstream direction in water year 2013 was attributed to either sedimentation in the intervening river reach, transfer to bedload as an alternate mode of sediment transport, or both.The sediment in the Sumas River is distinct from sediment in most other river systems because of the

  19. Mercury isotope constraints on the source for sediment-hosted lead-zinc deposits in the Changdu area, southwestern China

    Science.gov (United States)

    Xu, Chunxia; Yin, Runsheng; Peng, Jiantang; Hurley, James P.; Lepak, Ryan F.; Gao, Jianfeng; Feng, Xinbin; Hu, Ruizhong; Bi, Xianwu

    2018-03-01

    The Lanuoma and Cuona sediment-hosted Pb-Zn deposits hosted by Upper Triassic limestone and sandstone, respectively, are located in the Changdu area, SW China. Mercury concentrations and Hg isotopic compositions from sulfide minerals and potential source rocks (e.g., the host sedimentary rocks and the metamorphic basement) were investigated to constrain metal sources and mineralization processes. In both deposits, sulfide minerals have higher mercury (Hg) concentrations (0.35 to 1185 ppm) than the metamorphic basement rocks (0.05 to 0.15 ppm) and sedimentary rocks (0.02 to 0.08 ppm). Large variations of mass-dependent fractionation (3.3‰ in δ202Hg) and mass-independent fractionation (0.3‰ in Δ199Hg) of Hg isotopes were observed. Sulfide minerals have Hg isotope signatures that are similar to the hydrothermal altered rocks around the deposit, and similar to the metamorphic basement, but different from barren sedimentary rocks. The variation of Δ199Hg suggests that Hg in sulfides was mainly derived from the underlying metamorphic basement. Mercury isotopes could be a geochemical tracer in understanding metal sources in hydrothermal ore deposits.

  20. Possible pitfalls in the search for uranium deposits using lake sediments and lake waters

    International Nuclear Information System (INIS)

    Levinson, A.A.; Bland, C.J.

    1978-01-01

    The organic-rich sediments from the centres of Canadian lakes are a valuable sampling medium in the search for uranium. However, because of the young age of hydromorphically transported uranium in these sediments, which must post-date the last period of glaciation, there has been insufficient time for the isotope 214 Bi to reach equilibrium with its ancestor 238 U. This results in equivalent uranium (eU) values significantly lower than actual uranium values determined by fluorometry or delayed neutron activation analysis. Radiometric ( 226 Ra) analyses of 12 centre-lake sediments from Seahorse Lake, Saskatchewan illustrate the potential pitfalls which may be encountered using gamma-ray spectrometry, as only 3-8% of the actual uranium present in most of the samples would have been detected. (author)

  1. Sediment budgets, transport, and depositional trends in a large tidal delta

    Science.gov (United States)

    Morgan, Tara; Wright, Scott A.

    2016-01-01

    The Sacramento-San Joaquin Delta is the largest delta on the west coast of the United States. It is formed where the confluence of California’s two largest rivers (the Sacramento and San Joaquin) meet the ocean tides and has a significant physical gradient from fluvial to tidal. It is a semidiurnal system (two high and two low tides per day). Today, the Delta is one of the most manipulated in the United States. Once composed of many shallow, meandering and braided dendritic channels and dead-end sloughs and wetlands, it is now a network of leveed canals moving clear water around subsided islands. It historically has supported a biologically diverse tidal wetland complex, of which only 3% remains today (Whipple et al., 2012). It has also witnessed a collapse in the native fish populations. The Delta provides critical habitat for native species, however the hydrology and water quality are complicated by manipulations and diversions to satisfy multiple statewide objectives. Today water managers face co-equal goals of water supply to Californians and maintenance of ecosystem health and function. The Delta is a hub for both a multi-hundred-million dollar agricultural industry and a massive north-to-south water delivery system, supplying the primary source of freshwater to Central Valley farmers and drinking water for two-thirds of California’s population. Large pump facilities support the water demand and draw water from the Delta, further altering circulation patterns and redirecting the net flow toward the export facilities (Monsen et al., 2007). Fluvial sedimentation, along with organic accumulation, creates and sustains the Delta landscape. Hydraulic mining for gold in the watershed during the late 1800s delivered an especially large sediment pulse to the Delta. More recently, from 1955 to the present, a significant sediment decline has been observed that is thought to have been caused mostly by the construction of water storage reservoirs that trap the upstream

  2. Geochronologic study of sediments deposition of two lakes from the Rio Negro basin, Amazonas State, Brazil

    International Nuclear Information System (INIS)

    Gomes, Ana Carla F.; Mozeto, Antonio A.; Cazotti, Raul I.; Nascimento Filho, Virgilio F.; Taddei, Maria Helena

    2000-01-01

    Since 1963 the radionuclide 210 Pb became an important tool for dating (geochronology) recent sediments (up to 120 years). In this work the sedimentary geochronology of two lakes from the Negro River Basin was determined, using different radiochemical separation methods for 210 Pb and 226 Ra. (author)

  3. Sediment deposition from forest roads at stream crossings as influenced by road characteristics

    Science.gov (United States)

    A.J. Lang; W.M. Aust; M.C. Bolding; K.J. McGuire

    2015-01-01

    Recent controversies associated with ditched forest roads and stream crossings in the Pacific Northwest have focused national attention on sediment production and best management practices (BMPs) at stream crossings. Few studies have quantified soil erosion rates at stream crossings as influenced by road characteristics and compared them to modeled rates. Soil erosion...

  4. Depositional characteristics and sediment availability resulting from the post-Schultz Fire floods of 2010

    Science.gov (United States)

    Karen A. Koestner; Mike D. Carroll; Daniel G. Neary; Peter E. Koestner; Ann Youberg

    2011-01-01

    Wildfire is a major land management concern due to direct impacts of fire on forest resources, and potentially negative effects on landscape processes by increasing rates of runoff, erosion, downstream sedimentation, and overall site degradation (DeBano et al. 1998, Neary et al. 2005, Robichaud et al. 2010). In the United States the number of fires has been increasing...

  5. Deposition of Mn-Cu-Ni-enriched sediments during glacial period in the Central Indian Basin

    Digital Repository Service at National Institute of Oceanography (India)

    Borole, D.V.

    Two siliceous sediment cores collected from the Central Indian Basin have been analysed for organic carbon, biogenic silica, Al, Mn, Ni and Cu content. The concentrations of Mn, Cu and Ni showed one order of magnitude variation (an enrichment by a...

  6. Sedimentation and paleoecology of Pliocene lagoonal-shallow marine deposits on the island of Rhodes (Greece)

    NARCIS (Netherlands)

    Broekman, J.A.

    1974-01-01

    A detailed analysis of the depositional and paleontological characteristics of a section of the Pliocene Kritika Formation on the island of Rhodos is presented. The environmental significance of sedimentary structures, the paleoecology of benthonic Foraminifera, and the sequentional

  7. Christmas Island lagoonal lakes, models for the deposition of carbonate–evaporite–organic laminated sediments

    OpenAIRE

    Trichet , Jean; Défarge , Christian; Tribble , J.; Tribble , G.W.; Sansone , F.J.

    2001-01-01

    The atoll of Christmas Island (now known as Kiritimati) in the Kiribati Republic (Central Pacific) lies at about 2°N in the intertropical convergence zone. Much of the surface area of the atoll (ca. 360 km2) is occupied by numerous lakes in which carbonate, evaporite (calcium sulfate, halite) and organic layers are deposited. Observations suggest that deposition of these different laminae is controlled by climatic and biologic factors. It is thought that periodic climatic variations, such as ...

  8. Spatial distributions and deposition chronology of short chain chlorinated paraffins in marine sediments across the Chinese Bohai and Yellow Seas.

    Science.gov (United States)

    Zeng, Lixi; Chen, Ru; Zhao, Zongshan; Wang, Thanh; Gao, Yan; Li, An; Wang, Yawei; Jiang, Guibin; Sun, Liguang

    2013-10-15

    As the most complex halogenated contaminants, short chain chlorinated paraffins (SCCPs) are scarcely reported in marine environments. In this work, a total of 117 surficial sediment (0-3 cm) samples and two sediment cores were collected from the Chinese Bohai and Yellow Seas to systematically study the spatial and temporal trends of SCCPs at a large scale in the Chinese marine environment. Total SCCP concentrations in the surficial sediments were in the range of 14.5-85.2 ng g(-1) (dry weight, d.w.) with an average level of 38.4 ng g(-1) d.w. Spatial distribution showed a decreasing trend with the distance from the coast to the open waters. Compositional pattern analysis suggested that C10 was the most predominant homologue group, followed by C11, C12, and C13 homologue groups. The concentrations of total SCCPs in sediment cores ranged from 11.6 to 94.7 ng g(-1) d.w. for YS1 and from 14.7 to 195.6 ng g(-1) d.w. for YS2, with sharp rise from the early 1950s to present based on (210)Pb dating technique. The historical records in cores correspond well to the production and usage changes of CPs in China. Multivariate regression statistics indicate TOC, latitude and longitude are the major factors influencing surficial SCCP levels in the Chinese East Seas by combining analysis with the data from the East China Sea (R(2) = 0.332, p < 0.01). These findings indicated that the sources of SCCPs were mainly from river outflows via ocean current and partly from atmospheric depositions by East Asian monsoon in the sampling areas.

  9. Effects of river morphology, hydraulic gradients, and sediment deposition on water exchange and oxygen dynamics in salmonid redds.

    Science.gov (United States)

    Schindler Wildhaber, Y; Michel, C; Epting, J; Wildhaber, R A; Huber, E; Huggenberger, P; Burkhardt-Holm, P; Alewell, C

    2014-02-01

    Fine sediment decreasing gravel permeability and oxygen supply to incubating salmonid embryos, is often considered the main contributing factor for the observed decline of salmonid populations. However, oxygen supply to salmonid embryos also depends on hydraulic conditions driving water flow through the redd. A more generalized perspective is needed to better understand the constraints on successful salmonid incubation in the many heavily modified fluvial ecosystems of the Northern Hemisphere. The effects of hydraulic gradients, riverbed and redd morphology as well as fine sediment deposition on dissolved oxygen (DO) and water exchange was studied in 18 artificial redds at three sites along a modified river. Fifty percent of the redds in the two downstream sites were lost during high flow events, while redd loss at the upstream site was substantially lower (8%). This pattern was likely related to increasing flood heights from up- to downstream. Specific water infiltration rates (q) and DO were highly dynamic and driven on multiple temporal and spatial scales. Temporally, the high permeability of the redd gravel and the typical pit-tail structure of the new built redds, leading to high DO, disappeared within a month, when fine sediment had infiltrated and the redd structure was leveled. On the scale of hours to days, DO concentrations and q increased during high flows, but decreased during the falling limb of the water level, most likely related to exfiltration of oxygen depleted groundwater or hyporheic water. DO concentrations also decreased under prolonged base flow conditions, when increased infiltration of silt and clay particles clogged the riverbed and reduced q. Spatially, artificial log steps affected fine sediment infiltration, q and interstitial DO in the redds. The results demonstrate that multiple factors have to be considered for successful river management in salmonid streams, including riverbed structure and local and regional hydrogeological

  10. Bacterial profiling of Saharan dust deposition in the Atlantic Ocean using sediment trap moorings – year one results

    Science.gov (United States)

    Munday, Chris; Brummer, Geert-Jan; van der Does, Michelle; Korte, Laura; Stuut, Jan-Berend

    2015-04-01

    Large quantities of dust are transported from the Sahara Desert across the Atlantic Ocean towards the Caribbean each year, with a large portion of it deposited in the ocean. This dust brings an array of minerals, nutrients and organic matter, both living and dead. This input potentially fertilizes phytoplankton growth, with resulting knock-on effects throughout the food chain. The input of terrestrial microbial life may also have an impact on the marine microbial community. The current multi-year project consists of a transect of floating dust collectors and sub-surface sediment traps placed at 12°N across the Atlantic Ocean. Sediment traps are located 1200m and 3500m below the sea surface and all are synchronized to collect samples for a period of two weeks. The aim is to understand the links between dust input and the bacterial community and how this relates to ocean productivity and the carbon cycle. The first set of sediment trap samples were recovered using the RV Pelagia in November 2013 with promising results. Results from 7 sediment traps (three at 1200m and four at 3500m) were obtained. In general, the total mass flux decreased as distance from the source increased and the upper traps generally held more material than those at 3500m. Denaturing Gradient Gel Electrophoresis (DGGE) was used as a screening technique, revealing highly varied profiles, with the upper (1200m) traps generally showing more variation throughout the year. Several samples have been submitted for high throughput DNA sequencing which will identify the variations in these samples.

  11. Ecotoxicological evaluation of industrial port of Venice (Italy) sediment samples after a decontamination treatment.

    Science.gov (United States)

    Libralato, Giovanni; Losso, Chiara; Arizzi Novelli, Alessandra; Citron, Marta; Della Sala, Stefano; Zanotto, Emanuele; Cepak, Franka; Volpi Ghirardini, Annamaria

    2008-12-01

    This work assesses the ecotoxicological effects of polluted sediment after a decontamination treatment process using a new sediment washing technique. Sediment samples were collected from four sites in Marghera Port industrial channels (Venice, Italy). Ecotoxicological evaluations were performed with Vibrio fischeri and Crassostrea gigas bioassays. Whole sediment and elutriate were deemed as the most suitable environmental matrices for this study. Toxicity scores developed in the Lagoon of Venice for V. fischeri on whole sediment and for C. gigas on elutriate were considered for the final ranking of samples. Ecotoxicological results showed that the treated sediment samples presented both acute and sub-chronic toxicities, which were mainly attributed to the presence of some remaining chemicals such as metals and polyaromatic hydrocarbons. The acute toxicity ranged from low to medium, while the sub-chronic one from absent to very high, suggesting that treated sediments could not be reused in direct contact with seawater.

  12. NASA evaluation of Type 2 chemical depositions. [effects of deicer deposition on aircraft tire friction performance

    Science.gov (United States)

    Yager, Thomas J.; Stubbs, Sandy M.; Howell, W. Edward; Webb, Granville L.

    1993-01-01

    Recent findings from NASA Langley tests to define effects of aircraft Type 2 chemical deicer depositions on aircraft tire friction performance are summarized. The Aircraft Landing Dynamics Facility (ALDF) is described together with the scope of the tire cornering and braking friction tests conducted up to 160 knots ground speed. Some lower speed 32 - 96 km/hr (20 - 60 mph) test run data obtained using an Instrumented Tire Test Vehicle (ITTV) to determine effects of tire bearing pressure and transverse grooving on cornering friction performance are also discussed. Recommendations are made concerning which parameters should be evaluated in future testing.

  13. The applicability of the sediment deposition geochronology with 2'1'0PB as a tool in the sediment accumulation from the Taquari River, Pantanal, MS, Central region, Brazil

    International Nuclear Information System (INIS)

    Godoy, J.M.; Padovani, C.R.; Vieira, L.M.; Pereira, J.C.A.

    1998-01-01

    This work presents 210 Pb geochronology of five bottom sediment cores from flood plain lakes of middle Taquari River, Pantanal, MS. In two cores of a same lake, an increase of the sediment deposition rate were observed, reflecting an increasing of the sediment input to the Pantanal. The main causes suggested for this increasing are climatic change, and the development of agriculture and cattle-raising in the watershed highlands, for the last 25 years. The results pointed too for the importance of a additional sample in the superior region of the middle Taquari River. (author)

  14. Evaluation of Sediment Trap Efficiency in an Estuarine Environment

    National Research Council Canada - National Science Library

    Stoddard, Daniel

    2001-01-01

    .... A second trap of same dimensions was also incorporated 420 m upstream. Trap efficiency was calculated as a sediment removal ratio, or the percentage by which influent sediment load to the trap is reduced in the effluent load from the trap...

  15. The use of ecocores to evaluate biodegradation in marine sediments

    DEFF Research Database (Denmark)

    Jensen, Kurt; Albrechtsen, Hans-Jørgen; Nielsen, Jef

    1988-01-01

    A laboratory sediment microcosm called the ecocore is described. It has been used to test the biodegradability of substances which predominantly enter the sediment. A new method for introducing hydrophobic test substances such as hydrocarbons to the test system is also described. In a series...

  16. The Effect of Sedimentation Conditions of Frozen Deposits at the Kolyma Lowland on the Distribution of Methane and Microorganisms Activity

    Science.gov (United States)

    Oshurkova, V.; Kholodov, A. L.; Spektor, V.; Sherbakova, V.; Rivkina, E.

    2014-12-01

    Biogeochemical and microbiological investigations of methane distribution and origin in Northeastern Arctic permafrost sediments indicated that microbial methane production was observed in situ in thawed and permanently frozen deposits (Rivkina et al., 2007). To check the hypothesis about the correlation between permafrost ground type and quantity of methane, produced by microorganisms, the samples from deposits of thermokarst depression (alas), Yedoma and fluvial deposits of Kolyma floodplain for gas measurements and microbiological study were collected and the experiment with anaerobic incubation was conducted. Gas analysis indicated that alas and floodplain samples were characterized by high methane concentrations whereas Yedoma samples had only traces of methane. Two media with different substrates were prepared anaerobically for incubation. First medium contained sucrose as a substrate for hydrolytic microflora and the second one contained acetate as a substrate for methanogens. Two samples from alas, one sample from Yedoma and one from floodplain were placed in anaerobic bottles and media under gas mixture (N2, CO2 and H2) were added. The bottles were incubated for 2 weeks at room temperature. The results of the experiment showed that there was the increase of methane concentrations in the bottles with Yedoma and Floodplain samples to 52-60 and 67-90 %, respectively, from initial concentrations in contrast with Alas sample inoculated bottles. At the same time the concentration of methane in control bottles, which did not include substrates, increased to 15-19%. Current research is a part of NSF funded project "The Polaris".

  17. Corrosion and deposit evaluation in large diameter pipes using radiography

    International Nuclear Information System (INIS)

    Boateng, A.

    2012-01-01

    The reliability and safety of industrial equipment in the factories and processing industries are substantially influenced by degradation processes such as corrosion, erosion, deposits and blocking of pipes. These might lead to low production, unpredictable and costly shutdowns due to repair and replacement and sometimes combined environmental pollution and risk of personnel injuries. Only periodic inspection for the integrity of pipes and equipment can reduce the risk in connection with other maintenance activities. The research explored two methods of radiographic inspection techniques, the double wall technique and the tangential radiographic technique using Ir-192 for evaluating deposits and corrosion attacks across the inner and outer walls of steel pipes with diameter greater than 150 mm with or without insulation. The application of both techniques was conducted depending on pipe diameter, wall thickness, radiation source (Ir-92) and film combination. The iridium source was positioned perpendicular with respect to the pipe axis projecting the double wall of the pipe on the plated radiographic film. With the tangential radiographic technique, the source was placed tangential to the pipe wall and because of its large diameter, the source was collimated to prevent backscatter and also to focus the beam at the target area of interest. All measurements were performed on special designed test pieces to simulate corrosion attack and deposits on industrial pipes. Pitting corrosion measurements based on Tangential Radiographic Technique were more sophisticated, and therefore magnification factor and correction were used to establish the estimated pit depth on the film. The insulating material used to conserve the thermodynamic properties of the transported media had relatively negligible attenuation coefficient compared to the concrete deposit. The two explored techniques were successful in evaluating corrosion attack and deposit on the walls of the pipe and the risk

  18. Palynostratigraphy, palynofacies and palaeoenvironment of deposition of Selandian to Aquitanian sediments, southeastern Nigeria

    Science.gov (United States)

    Okeke, Kingsley K.; Umeji, Obianuju P.

    2016-08-01

    Investigation of outcrop sections along the Onitsha-Awka transect in the Niger Delta Basin southeastern Nigeria was undertaken to assess the palynological composition, palynofacies and palaeoenvironment of deposition. Stratigraphic ranges of palynomorphs suggest an age of Selandian to Aquitanian. The palynological composition is marked by abundance of dinoflagellate cysts in the Imo Formation (Selandian to Thanetian), dominance of spores and pollen over dinoflagellate cysts in the Nanka Formation (Ypresian to Bartonian), and overwhelming amounts of spore and pollen in the Ogwashi Formation (Pariabonian to Aquitanian). Palynofacies content shows dominance of structureless organic matter in the Imo Formation, few phytoclasts in the Nanka Formation and maximum phytoclast amounts in the Ogwashi Formation. Thanetian to Ypresian boundary was marked by the mixing of older Palaeocene and younger Eocene microfossils, decrease of microflora towards the end of Palaeocene and the evolution of abundant and more diverse Eocene taxa. The Imo Formation was deposited in middle to outer neritic zone based on abundance of gonyaulacacean cysts. However, peridiniacean and terrestrial microflora extend the deposition range to shallow waters of inner neritic and coastal zone. Increase in diversity and abundance of terrestrial palynomorphs over marine palynomorphs assemblages in the overlying Nanka Formation suggest deposition under alternating coastal and inner neritic conditions while the Ogwashi Formation records oscillating coastal plain and brackish water depositional conditions. The palaeoenvironments illustrate that general retrogradation was followed by progradation of the delta during the Cenozoic.

  19. Influence of variable rates of neritic carbonate deposition on atmospheric carbon dioxide and pelagic sediments

    Science.gov (United States)

    Walker, J. C.; Opdyke, B. C.

    1995-01-01

    Short-term imbalances in the global cycle of shallow water calcium carbonate deposition and dissolution may be responsible for much of the observed Pleistocene change in atmospheric carbon dioxide content. However, any proposed changes in the alkalinity balance of the ocean must be reconciled with the sedimentary record of deep-sea carbonates. The possible magnitude of the effect of shallow water carbonate deposition on the dissolution of pelagic carbonate can be tested using numerical simulations of the global carbon cycle. Boundary conditions can be defined by using extant shallow water carbonate accumulation data and pelagic carbonate deposition/dissolution data. On timescales of thousands of years carbonate deposition versus dissolution is rarely out of equilibrium by more than 1.5 x 10(13) mole yr-1. Results indicate that the carbonate chemistry of the ocean is rarely at equilibrium on timescales less than 10 ka. This disequilibrium is probably due to sea level-induced changes in shallow water calcium carbonate deposition/dissolution, an interpretation that does not conflict with pelagic sedimentary data from the central Pacific.

  20. Technical Guidelines on Performing a Sediment Erosion and Deposition Assessment (SEDA) at Superfund Sites

    Science.gov (United States)

    2014-09-01

    introduced to a water body because of the failure of a river bank due to, for example, flow-induced erosion of the bank toe and/or surface, or...under supercritical flows (with Froude number greater than one). Antidunes are usually more symmetrical (in their longitudinal profile) than dunes ... dunes , and anti- dunes . Bedload Sediment material moving on top of or near a channel bed by rolling, sliding, and saltating, i.e., jumping

  1. Mapping sediment deposite on tank FB-901 using neutron back scattering technique

    International Nuclear Information System (INIS)

    Wibisono; Sugiharto; Zulkifli Lubis; Phyu Phyu Aung Myint; Thin Moe Hlaing

    2016-01-01

    Tank FB-901 is storage tank for temporary material production with a diameter 11 m and a high 12 m. This tank has been use about 10 years so it is suspected there is sediment in it. Neutron back scattering technique has been used to detected the level of sediment inside so it can be seen the volume of liquid properly and avoid problem in the nozzle outlet. AmBe neutron source with activity one Curie shoot into the tank to enable back scattering intensity from material. Measurement using He-3 detector, radiation counter Ludlum model 2200 scaler ratemeter and mechanical motor controlled by computer. Investigation were taken at around the tank from the bottom to the top on each step 50 mm height 8000 mm. Scan determined the distance between 500 mm and measurement time 3 seconds to each sample point. Investigation found the sediment level average 1000 mm by 1500 mm highest and lowest level 100 mm. Fluctuating liquid level observed maximum of 7800 mm and average of 7000 mm. Cleaning tank advised to avoid blockage of the nozzle and material volume is measured accurately. (author)

  2. Deposition behavior, risk assessment and source identification of heavy metals in reservoir sediments of Northeast China.

    Science.gov (United States)

    Zhu, Lin; Liu, Jianwei; Xu, Shiguo; Xie, Zaigang

    2017-08-01

    Sediment cores from five reservoirs, located in the Liaoning and Jilin Provinces in Northeast China, were collected to investigate the accumulation and potential toxicity of heavy metals (Fe, Mn, Cu, Cd, Pb, Zn, and Cr) during a sampling campaign in February, 2015. The results showed that all the detected metals accumulated significantly, especially Cd, compared to their respective background values. Among these reservoirs, Biliuhe Reservoir had markedly increasing trends for organic matter and all the metals, among which Mn was elevated by 280% to 3411mg/kg in a core of only 18cm in depth. Xinlicheng Reservoir was characterized by heavy siltation and varying metal distribution due to its regular geometric features and pulsed flood events. The Enrichment factor (EF) and geo-accumulation index (I geo ) indicated Cd was strongly enriched by anthropogenic inputs, with the values of EF and I geo greater than 8 and 3, respectively. The toxicity assessment calculated using consensus-based sediment quality guidelines (SQGs) implied the whole cores of Tanghe and Dahuofang and the upper cores of Biliuhe, Xinlicheng and Fengman exhibited toxicity to sediment-dwelling organisms. Cr contributed more to Q m-PEC than the other heavy metals, because only Cr exceeded the probable effect concentration (PEC) despite its low enrichment. According to the results of correlation analysis (CA) and principal components analysis (PCA), mining industries and agricultural activities within the basin were the main anthropogenic pollution sources for these heavy metals. Copyright © 2017 Elsevier Inc. All rights reserved.

  3. Depositional dynamics in the El'gygytgyn Crater margin: implications for the 3.6 Ma old sediment archive

    Directory of Open Access Journals (Sweden)

    G. Schwamborn

    2012-11-01

    Full Text Available The combination of permafrost history and dynamics, lake level changes and the tectonical framework is considered to play a crucial role for sediment delivery to El'gygytgyn Crater Lake, NE Russian Arctic. The purpose of this study is to propose a depositional framework based on analyses of the core strata from the lake margin and historical reconstructions from various studies at the site. A sedimentological program has been conducted using frozen core samples from the 141.5 m long El'gygytgyn 5011-3 permafrost well. The drill site is located in sedimentary permafrost west of the lake that partly fills the El'gygytgyn Crater. The total core sequence is interpreted as strata building up a progradational alluvial fan delta. Four macroscopically distinct sedimentary units are identified. Unit 1 (141.5–117.0 m is comprised of ice-cemented, matrix-supported sandy gravel and intercalated sandy layers. Sandy layers represent sediments which rained out as particles in the deeper part of the water column under highly energetic conditions. Unit 2 (117.0–24.25 m is dominated by ice-cemented, matrix-supported sandy gravel with individual gravel layers. Most of the Unit 2 diamicton is understood to result from alluvial wash and subsequent gravitational sliding of coarse-grained (sandy gravel material on the basin slope. Unit 3 (24.25–8.5 m has ice-cemented, matrix-supported sandy gravel that is interrupted by sand beds. These sandy beds are associated with flooding events and represent near-shore sandy shoals. Unit 4 (8.5–0.0 m is ice-cemented, matrix-supported sandy gravel with varying ice content, mostly higher than below. It consists of slope material and creek fill deposits. The uppermost metre is the active layer (i.e. the top layer of soil with seasonal freeze and thaw into which modern soil organic matter has been incorporated. The nature of the progradational sediment transport taking place from the western and northern crater margins may be

  4. Descriptive models, grade-tonnage relations, and databases for the assessment of sediment-hosted copper deposits: with emphasis on deposits in the Central Africa Copperbelt, Democratic Republic of the Congo and Zambia: Chapter J in Global mineral resource assessment

    Science.gov (United States)

    Taylor, Cliff D.; Causey, J. Douglas; Denning, Paul; Hammarstrom, Jane M.; Hayes, Timothy S.; Horton, John D.; Kirschbaum, Michael J.; Parks, Heather L.; Wilson, Anna B.; Wintzer, Niki E.; Zientek, Michael L.

    2013-01-01

    The Central African Copperbelt (CACB) is one of the most important copper-producing regions of the world. The majority of copper produced in Africa comes from this region defined by the Neoproterozoic Katanga sedimentary basin of the southern Democratic Republic of the Congo (DRC) and northern Zambia. Copper in the CACB is mined from sediment-hosted stratabound copper deposits associated with red beds and includes the giant deposits in the Kolwezi and Tenge-Fungurume districts in the DRC and the Konkola-Musoshi and Nchanga-Chingola districts in Zambia. In recent years, sediment-hosted structurally controlled replacement and vein (SCRV) copper deposits, such as the giant Kansanshi deposit in Zambia have become important exploration targets in the CACB region.

  5. Determining the Role of Sediment Deposition and Transport in the Formation and Maintenance of Tree Islands in the Florida Everglades

    Science.gov (United States)

    Mitchell-Bruker, S.; Childers, D.; Ross, M.; Leonard, L.; Solo-Gabriel, H.; Stothoff, S.

    2002-05-01

    Tree islands are a prominent feature in the Everglades ridge and slough wetlands. These tree islands are believed to be a remnant of the historical pre-drainage flow system. Within Everglades National Park, hardwood hammock and bayhead tree islands commonly form as teardrop-shaped mounds, rising above the sawgrass marsh. These tree islands are usually oriented along the direction of surface water flow, with the highest elevation and widest part of the island at the upstream head. The island narrows as it descends into the marsh at the downstream end, terminating in a tail that sometimes includes a zone of dead or dying sawgrass. The shape and orientation of the tree islands suggests that surface water flow has been instrumental in their formation, however occasional flow measurements indicate that the slow moving water of the Everglades does not provide sufficient energy to transport even moderate amounts of suspended sediment. This low flow velocity, coupled with the extremely low turbidity of the Everglades water suggests that if sediment transport and deposition processes are instrumental in forming tree islands, the process is probably occurring over short distances and long time intervals. It is also possible that concentration and transport of nutrients is an important element in tree island formation. Because the Everglades marsh is a low nutrient environment, processes that create areas of increased phosphorous concentration result in changes in the vegetation. Because many hardwood hammock and bayhead tree islands have heads that are situated on bedrock highs, the higher and drier elevation of the head allows for trees to grow. These trees could concentrate phosphorous either by acting as wildlife attractors, or by acting as \\x8Dphosphorous pumpsŒ, transporting groundwater with high concentrations of phosphorous through the roots to the tree. We are characterizing vegetation, litter fall, sediments, surface water flow, hydrologic gradients and nutrient

  6. Evaluation of soft sediment deformation structures along the Fethiye ...

    Indian Academy of Sciences (India)

    pore-pressure changes induced by liquefaction and fluidization ... (iii) escape of water or shaking of sediment due to. Keywords. ... from well exposed (a) retaining wall excavation area (Site ..... Absorption Spectroscopy and therefore, the effect.

  7. Geophysical imaging of the lacustrine sediments deposited in the La Calderilla Volcanic Caldera (Gran Canaria Island, Spain) for paleoclimate research

    Science.gov (United States)

    Himi, Mahjoub; Rodríguez-González, Alejandro; Criado, Constantino; Tapias, Josefina C.; Ravazzi, Cesare; Pérez-Torrado, Francisco; Casas, Albert

    2016-04-01

    The discovery of well-preserved maar structures is important not only for studying the eruptive activity and formation of volcanoes, but also for paleoclimate research, since laminated maar lake sediments may contain very detailed archives of climate and environmental history. Maars are a singular type of volcanic structure generated by explosive phreatomagmatic eruptions as a result of interaction between rising magma and groundwater. This kind of structures are characterised by circular craters, often filled with water and/or lacustrine sediments and surrounded by a ring of pyroclastic deposits.Recently a borehole was drilled at the bottom of La Calderilla volcanic complex which penetrated about 8.7 m in its sedimentary sequence and paleobotanical study has supplied the first evidence of paleoenvironmental evolution during the Holocene on the Gran Canaria Island. This survey, however, did not penetrate into the substrate because the total thickness of the sedimentary fill was unknown. Since the age of formation of La Calderilla volcanic complex based on K/Ar dating is about 85,000 years (Upper Pleistocene), the possibility of its sedimentary fill extends beyond of the Holocene is extremely attractive, since, for example, there are few paleoenvironmental data regarding how much the last glaciation that affected the Canary Islands. In these circumstances, the knowledge of the total thickness of the lacustrine sediments is crucial to design a deeper borehole in the next future. Therefore, the subsurface characterisation provided by geophysics is essential for determining thickness and geometry of the sedimentary filling. Multielectrode ERT method was used to obtain five 2-D resistivity cross-sections into La Calderilla volcanic caldera. An Iris Syscal Pro resistivity system with 48 electrodes connected to a 94 m long cable (2m electrode spacing) in Wenner-Schlumberger configuration for an investigation depth of about 20 m. Data quality (q Current injected was

  8. Morava River flood plain sediments deposited during the last millennium: Climatic and anthropogenic record

    Czech Academy of Sciences Publication Activity Database

    Kadlec, Jaroslav; Grygar, Tomáš; Světlík, Ivo; Ettler, V.; Mihaljevič, M.; Diehl, J.; Beske-Diehl, S.

    2008-01-01

    Roč. 34, 4/6 (2008), s. 1338314-1338314 ISSN 0161-6951. [International Geological Congress /33./. 06.08.2008-14.08.2008, Oslo ] R&D Projects: GA AV ČR IAA300130505; GA AV ČR IAA3013201; GA AV ČR IAAX00130801 Institutional research plan: CEZ:AV0Z30130516; CEZ:AV0Z40320502; CEZ:AV0Z10480505 Keywords : Morava River * flood * plain sediments * magnetic minerals Subject RIV: DB - Geology ; Mineralogy

  9. Towards an event stratigraphy for Baltic Sea sediments deposited since AD 1900

    DEFF Research Database (Denmark)

    Moros, Matthias; Andersen, Thorbjørn Joest; Schulz-Bull, Detlef

    2017-01-01

    of anthropogenic radionuclides (137Cs/241Am/bomb14C), polychlorinated biphenyls (PCBs), lead (Pb) and stable lead isotope (206/207Pb ratios), and radionuclide 210Pb and 14C decay dating methods. Marker horizons consisting of chemical precipitates formed by documented Major Baltic Inflow (MBIs) events...... and an extended diatom bloom period were also integrated into the model. The main time markers in Baltic Sea sediments that formed during the last 120 years were the following: (i) the deepest observation of 210Pbunsupp. (marking the 210Pb dating horizon) and departure of Hg from natural background levels at c...

  10. Effects of sediment-associated copper to the deposit-feeding snail, Potamopyrgus antipodarum

    DEFF Research Database (Denmark)

    Pang, Chengfang; Selck, Henriette; Misra, Superb K

    2012-01-01

    the case of metal oxide NPs using CuO to understand if the effects of NPs differ from micron-sized particles of CuO and aqueous Cu (CuCl2). To address this issue, we compared effects of copper added to the sediment as aqueous Cu, nano- (6 nm) and micro- (... greater effects on growth, feeding rate, and reproduction of P. antipodarum than copper added as micro-CuO or aqueous Cu. P. antipodarum accumulated more copper in the nano-CuO treatment than in aqueous Cu or micro-CuO treatments, indicating that consideration of metal form may be important when assessing...

  11. Numerical experiment on tsunami deposit distribution process by using tsunami sediment transport model in historical tsunami event of megathrust Nankai trough earthquake

    Science.gov (United States)

    Imai, K.; Sugawara, D.; Takahashi, T.

    2017-12-01

    A large flow caused by tsunami transports sediments from beach and forms tsunami deposits in land and coastal lakes. A tsunami deposit has been found in their undisturbed on coastal lakes especially. Okamura & Matsuoka (2012) found some tsunami deposits in the field survey of coastal lakes facing to the Nankai trough, and tsunami deposits due to the past eight Nankai Trough megathrust earthquakes they identified. The environment in coastal lakes is stably calm and suitable for tsunami deposits preservation compared to other topographical conditions such as plains. Therefore, there is a possibility that the recurrence interval of megathrust earthquakes and tsunamis will be discussed with high resolution. In addition, it has been pointed out that small events that cannot be detected in plains could be separated finely (Sawai, 2012). Various aspects of past tsunami is expected to be elucidated, in consideration of topographical conditions of coastal lakes by using the relationship between the erosion-and-sedimentation process of the lake bottom and the external force of tsunami. In this research, numerical examination based on tsunami sediment transport model (Takahashi et al., 1999) was carried out on the site Ryujin-ike pond of Ohita, Japan where tsunami deposit was identified, and deposit migration analysis was conducted on the tsunami deposit distribution process of historical Nankai Trough earthquakes. Furthermore, examination of tsunami source conditions is possibly investigated by comparison studies of the observed data and the computation of tsunami deposit distribution. It is difficult to clarify details of tsunami source from indistinct information of paleogeographical conditions. However, this result shows that it can be used as a constraint condition of the tsunami source scale by combining tsunami deposit distribution in lakes with computation data.

  12. Mercury contaminated sediment sites—An evaluation of remedial options

    Energy Technology Data Exchange (ETDEWEB)

    Randall, Paul M., E-mail: randall.paul@epa.gov [U.S. Environmental Protection Agency, Office of Research and Development, National Risk Management Research Laboratory, 26 West Martin Luther King Drive, Cincinnati, OH 45268 (United States); Chattopadhyay, Sandip, E-mail: Sandip.Chattopadhyay@tetratech.com [Tetra Tech, Inc., 250 West Court Street, Suite 200W, Cincinnati, OH 45202 (United States)

    2013-08-15

    Mercury (Hg) is a naturally-occurring element that is ubiquitous in the aquatic environment. Though efforts have been made in recent years to decrease Hg emissions, historically-emitted Hg can be retained in the sediments of aquatic bodies where they may be slowly converted to methylmercury (MeHg). Consequently, Hg in historically-contaminated sediments can result in high levels of significant exposure for aquatic species, wildlife and human populations consuming fish. Even if source control of contaminated wastewater is achievable, it may take a very long time, perhaps decades, for Hg-contaminated aquatic systems to reach relatively safe Hg levels in both water and surface sediment naturally. It may take even longer if Hg is present at higher concentration levels in deep sediment. Hg contaminated sediment results from previous releases or ongoing contributions from sources that are difficult to identify. Due to human activities or physical, chemical, or biological processes (e.g. hydrodynamic flows, bioturbation, molecular diffusion, and chemical transformation), the buried Hg can be remobilized into the overlying water. Hg speciation in the water column and sediments critically affect the reactivity (i.e. conversion of inorganic Hg(II) to MeHg), transport, and its exposure to living organisms. Also, geochemical conditions affect the activity of methylating bacteria and its availability for methylation. This review paper discusses remedial considerations (e.g. key chemical factors in fate and transport of Hg, source characterization and control, environmental management procedures, remediation options, modeling tools) and includes practical case studies for cleaning up Hg-contaminated sediment sites. -- Highlights: ► Managing mercury-contaminated sediment sites are challenging to remediate. ► Remediation technologies are making a difference in managing these sites. ► Partitioning plays a dominant role in the distribution of mercury species. ► Mathematical

  13. The history and source of particulate 137Cs and 239,240Pu deposition in sediments of the Ob River Delta, Siberia

    International Nuclear Information System (INIS)

    Sayles, F.L.; Livingston, H.D.; Panteleyev, G.P.

    1997-01-01

    This paper presents the first results of a project designed to examine the transfer of particle-associated artificial radionuclides down the Ob River in Siberia to its delta over the past 5 decades. The main sources include fallout from atmospheric nuclear weapons tests and weapons complexes and test sites of the Former Soviet Union in or near the Ob watershed. The approach is to measure the accumulation of the radionuclides in undisturbed delta sediments - obtaining a record of their deposition over time. These records were found in sediments of shallow lakes apart from, and connected to, the main channel. Sediment cores were collected in the summer of 1994 using a shallow draft catamaran to reach these lakes from a support ship in the main channel. Measurements are presented on the depth distributions of 137 Cs and Pu isotopes and their inventories in a series of dated sediment cores - including one from a location in the Taz Estuary (which does not receive Ob River sediments). Sediment dating was carried out using the excess 210 Pb technique. The results obtained are compared with known information on the temporal history of releases from the various sources and characteristics of the isotopic composition of the sources. The results show that good records of radionuclide deposition indicate that the major fraction of 137 Cs and Pu isotopes deposited in these delta sediments comes from atmospheric nuclear weapons test fallout - both delivered directly from the atmosphere and from downstream transport of watershed sediments. No more than 25% of the observed inventories could be derived from other sources

  14. Multivariate methods for evaluating the efficiency of electrodialytic removal of heavy metals from polluted harbour sediments

    DEFF Research Database (Denmark)

    Pedersen, Kristine Bondo; Kirkelund, Gunvor Marie; Ottosen, Lisbeth M.

    2015-01-01

    , dry/wet sediment, cell set-up as well as sediment properties. Evaluation of the model showed that remediation time and current density had the highest comparative influence on the clean-up levels. Individual models for each heavy metal showed variance in the variable importance, indicating...... that the targeted heavy,metals were bound to different sediment fractions. Based on the results, a PLS model was used to design five new EDR experiments of a sixth sediment to achieve specified clean-up levels of Cu and Pb. The removal efficiencies were up to 82% for Cu and 87% for Pb and the targeted clean...

  15. Chemical and biological evaluation of sediments from the Wadden Sea, The Netherlands

    NARCIS (Netherlands)

    Brink, van den P.J.; Kater, B.J.

    2006-01-01

    We describe the results of an evaluation of marine sediments using chemical measurements and bioassays. Four groups of chemicals, i.e., heavy metals, PAHs, chlorinated aromatic compounds, and tin compounds, were measured at 16 locations in the Wadden Sea, The Netherlands. Extractions of sediments

  16. EVALUATION OF THE STATE-OF-THE-ART CONTAMINATED SEDIMENT TRANSPORT AND FATE MODELING SYSTEM

    Science.gov (United States)

    Modeling approaches for evaluating the transport and fate of sediment and associated contaminants are briefly reviewed. The main emphasis is on: 1) the application of EFDC (Environmental Fluid Dynamics Code), the state-of-the-art contaminated sediment transport and fate public do...

  17. An evaluation of contaminated estuarine sites using sediment quality guidelines and ecological assessment methodologies.

    Science.gov (United States)

    Fulton, M; Key, P; Wirth, E; Leight, A K; Daugomah, J; Bearden, D; Sivertsen, S; Scott, G

    2006-10-01

    Toxic contaminants may enter estuarine ecosystems through a variety of pathways. When sediment contaminant levels become sufficiently high, they may impact resident biota. One approach to predict sediment-associated toxicity in estuarine ecosystems involves the use of sediment quality guidelines (ERMs, ERLs) and site-specific contaminant chemistry while a second approach utilizes site-specific ecological sampling to assess impacts at the population or community level. The goal of this study was to utilize an integrated approach including chemical contaminant analysis, sediment quality guidelines and grass shrimp population monitoring to evaluate the impact of contaminants from industrial sources. Three impacted sites and one reference site were selected for study. Grass shrimp populations were sampled using a push-netting approach. Sediment samples were collected at each site and analyzed for metals, polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and pesticides. Contaminant levels were then compared to sediment quality guidelines. In general, grass shrimp population densities at the sites decreased as the ERM quotients increased. Grass shrimp densities were significantly reduced at the impacted site that had an ERM exceedance for chromium and the highest Mean ERM quotient. Regression analysis indicated that sediment chromium concentrations were negatively correlated with grass shrimp density. Grass shrimp size was reduced at two sites with intermediate levels of contamination. These findings support the use of both sediment quality guidelines and site-specific population monitoring to evaluate the impacts of sediment-associated contaminants in estuarine systems.

  18. Geochemical and geological constraints on the composition of marine sediment pore fluid: Possible link to gas hydrate deposits

    Digital Repository Service at National Institute of Oceanography (India)

    Mazumdar, A.; Joao, H.M.; Peketi, A.; Dewangan, P.; Kocherla, M.; Joshi, R.K.; Ramprasad, T.

    Pore water sulfate consumption in marine sediments is controlled by microbially driven sulfate reduction via organo-clastic and methane oxidation processes. In this work, we present sediment pore fluid compositions of 10 long sediment cores and high...

  19. Araçatuba Formation: palustrine deposits from the initial sedimentation phase of the Bauru Basin

    Directory of Open Access Journals (Sweden)

    Fernandes Luiz A.

    2003-01-01

    Full Text Available The Bauru Basin (Upper Cretaceous accumulated an essentially sandy continental sedimentary sequence. In a first desertic phase the basaltic substratum was covered by a widespread and homogeneous aeolian sand unit with minor loess intercalations. The substratum relief favored the formation of an endorheic drainage system under semi-arid climate, a process that started the development of the Araçatuba Paleoswamp. The palustrine deposits (Araçatuba Formation comprise siltstone and tipically greenish gray narrow tabular strata of sandstone cemented by carbonate. Moulds and gypsite and dolomite pseudomorphs were identified. The moulds seem to be genetically associated with desiccation cracks, root marks and climbing ripple lamination levels, that, on the whole, indicate calm shallow saline waters undergoing phases of subaerial exposition. At the boundaries of the study area, sand units may exhibit sigmoidal features and convolute bedding structure, which is characteristic of marginal deltaic deposits. The Araçatuba Formation is enclosed in and later overlaid by the aeolian deposits of the Vale do Rio do Peixe Formation.

  20. Evaluation of energy deposition by 153Sm in small samples

    International Nuclear Information System (INIS)

    Cury, M.I.C.; Siqueira, P.T.D.; Yoriyaz, H.; Coelho, P.R.P.; Da Silva, M.A.; Okazaki, K.

    2002-01-01

    Aim: This work presents evaluations of the absorbed dose by 'in vitro' blood cultures when mixed with 153 Sm solutions of different concentrations. Although 153 Sm is used as radiopharmaceutical mainly due to its beta emission, which is short-range radiation, it also emits gamma radiation which has a longer-range penetration. Therefore it turns to be a difficult task to determine the absorbed dose by small samples where the infinite approximation is no longer valid. Materials and Methods: MCNP-4C (Monte Carlo N - Particle transport code) has been used to perform the evaluations. It is not a deterministic code that calculates the value of a specific quantity solving the physical equations involved in the problem, but a virtual experiment where the events related to the problems are simulated and the concerned quantities are tallied. MCNP also stands out by its possibilities to specify geometrically any problem. However, these features, among others, turns MCNP in a time consuming code. The simulated problem consists of a cylindrical plastic tube with 1.5 cm internal diameter and 0.1cm thickness. It also has 2.0 cm height conic bottom end, so that the represented sample has 4.0 ml ( consisted by 1 ml of blood and 3 ml culture medium). To evaluate the energy deposition in the blood culture in each 153 Sm decay, the problem has been divided in 3 steps to account to the β- emissions (which has a continuum spectrum), gammas and conversion and Auger electrons emissions. Afterwards each emission contribution was weighted and summed to present the final value. Besides this radiation 'fragmentation', simulations were performed for many different amounts of 153 Sm solution added to the sample. These amounts cover a range from 1μl to 0.5 ml. Results: The average energy per disintegration of 153 Sm is 331 keV [1]. Gammas account for 63 keV and β-, conversion and Auger electrons account for 268 keV. The simulations performed showed an average energy deposition of 260 ke

  1. The Eocene Rusayl Formation, Oman, carbonaceous rocks in calcareous shelf sediments: Environment of deposition, alteration and hydrocarbon potential

    Energy Technology Data Exchange (ETDEWEB)

    Dill, H.G.; Wehner, H.; Kus, J. [Federal Institute for Geosciences and Natural Resources, P.O. Box 510163, D-30631 Hannover (Germany); Botz, R. [University Kiel, Geological-Paleontological Department, Olshausenstrasse 40-60, D-24118 Kiel (Germany); Berner, Z.; Stueben, D. [Technical University Karlsruhe, Institute for Mineralogy and Geochemistry, Fritz-Haber-Weg 2, D-76131 Karlsruhe (Germany); Al-Sayigh, A. [Sultan Qaboos University, Geological Dept. PO Box 36, Al-Khod (Oman)

    2007-10-01

    Paralic carbonaceous series intercalated among calcareous shelf sediments have seldom been investigated. During the early Eocene, calcareous and siliciclastic sediments were deposited on a wide shelf in front of low-reliefed hinterland in the Al Khawd region in NE Oman. The siliciclastic-calcareous sediments originated from strongly reworked debris of the Arabic Shield. The underlying Semail Ophiolite did not act as a direct source of debris but provided some heat to increase the maturity of carbonaceous rocks and modify the isotope signal of the calcareous minerals in the Rusayl Formation. A multidisciplinary approach involving sedimentology, mineralogy, chemistry, coal petrography and paleontology resulted in the establishment of nine stratigraphic lithofacies units and provides the reader with a full picture from deposition of the mixed carbonaceous-calcareous-siliciclastic rocks to the most recent stages of post-depositional alteration of the Paleogene formations. The calcareous Jafnayn Formation (lithofacies unit I) developed in a subtidal to intertidal regime, influenced episodically by storms. Deepening of the calcareous shelf towards younger series was ground to a halt by paleosols developing on a disconformity (lithofacies unit II) and heralding the onset of the Rusayl Formation. The stratigraphic lithofacies units III and IV reflect mangrove swamps which from time to time were flooded through washover fans from the open sea. The presence of Spinozonocolpites and the taxon Avicennia, which today belong to a coastal marsh vegetational community, furnish palynological evidence to the idea of extensive mangrove swamps in the Rusayl Formation [El Beialy, S.Y., 1998. Stratigraphic and palaeonenvironmental significance of Eocene palynomorphs from the Rusayl Shale Formation, Al Khawd, northern Oman. Review of Palaeobotany and Palynology 102, 249-258]. During the upper Rusayl Formation (lithofacies units V through VII) algal mats episodically flooded by marine

  2. Bioaccumulation and effect of sediment-associated silver in different forms in two marine deposit feeders

    DEFF Research Database (Denmark)

    Dai, Lina; Banta, Gary Thomas; Syberg, Kristian

    2014-01-01

    Due to wide spread applications of nanoparticles, including Ag, in our daily life, these novel particles are receiving increasing attention by risk assessors. Many studies have been performed to test the toxicity of nanoparticles at the subcellular level. Despite these findings, there is still...... limited information at the whole organism level as to whether metallo-nanoparticles differ in toxicity from the same metals added to the environment in ionic or bulk form. In the present study, two organisms (i.e., a marine polychaete, Capitella teleta and a marine bivalve, Macoma balthica) were exposed...... to sediment amended with Ag in various forms (ionic Ag(I), nano-sized Ag and micron-sized Ag), and toxic endpoints were assessed at the whole organism level. After exposure for several weeks, no significant toxic effects were detected (i.e., mortality, growth rate and condition index) at the whole organism...

  3. Cross-stratified Wood: Enigmatic Woody Debris Deposits in Warm-Polar Fluvial Sediments (Pliocene Beaufort Formation, Nunavut)

    Science.gov (United States)

    Davies, N. S.; Gosse, J. C.; Rybczynski, N.

    2012-04-01

    Woody debris has been an important sediment component and a significant geomorphic agent in pristine fluvial systems since the Devonian. In recent years a large volume of research has focussed on various aspects of the importance of woody debris within the fluvial realm; from the evolutionary significance of fossil wood accumulations in the rock record to studies of the biogeomorphological and ecological importance of woody debris in modern rivers. In this presentation we describe cross-stratified woody debris deposits comprising organic detritus from a boreal-type treeline forest that included species of pine, birch, poplar, alder, spruce, eastern cedar, and larch, in both shrub and tree form. The cross-stratified wood is an enigmatic subset of fine woody debris which, to our knowledge, has never before been described from either the global stratigraphic record or modern fluvial environments. The deposits we describe are located within the Pliocene Beaufort Formation on Meighen Island, Nunavut, Canada, at a latitude of 80°N, and are compared with other cross-stratified woody debris deposits that have been noted elsewhere in the Pliocene of the Canadian Arctic. We make the robust observation that these deposits appear to be geographically and stratigraphically restricted to polar latitudes from a period of warm climatic conditions during the Pliocene (15-20 °C warmer mean annual temperature than the present day). In this regard it is possible to speculate that the transport of large amounts of woody debris as bedload is potentially a unique feature of forested high latitude rivers. Such bedload deposition requires a large amount of woody debris with a greater density than the fluid transporting it. The softwood composition of the debris suggests that this was most likely attained by saturation and subsequent entrainment of extensive accumulations of deadwood, promoted by unusually high rates of tree mortality and low rates of bacterial decomposition arising from

  4. Ecotoxicological evaluation of industrial port of Venice (Italy) sediment samples after a decontamination treatment

    International Nuclear Information System (INIS)

    Libralato, Giovanni; Losso, Chiara; Arizzi Novelli, Alessandra; Citron, Marta; Della Sala, Stefano; Zanotto, Emanuele; Cepak, Franka; Volpi Ghirardini, Annamaria

    2008-01-01

    This work assesses the ecotoxicological effects of polluted sediment after a decontamination treatment process using a new sediment washing technique. Sediment samples were collected from four sites in Marghera Port industrial channels (Venice, Italy). Ecotoxicological evaluations were performed with Vibrio fischeri and Crassostrea gigas bioassays. Whole sediment and elutriate were deemed as the most suitable environmental matrices for this study. Toxicity scores developed in the Lagoon of Venice for V. fischeri on whole sediment and for C. gigas on elutriate were considered for the final ranking of samples. Ecotoxicological results showed that the treated sediment samples presented both acute and sub-chronic toxicities, which were mainly attributed to the presence of some remaining chemicals such as metals and polyaromatic hydrocarbons. The acute toxicity ranged from low to medium, while the sub-chronic one from absent to very high, suggesting that treated sediments could not be reused in direct contact with seawater. - A sediment washing technique was assessed for port contaminated sediment remediation and reuse, indicating its reduced efficiency and the need for further improvements

  5. Ecotoxicological evaluation of industrial port of Venice (Italy) sediment samples after a decontamination treatment

    Energy Technology Data Exchange (ETDEWEB)

    Libralato, Giovanni [Environmental Sciences Department, Venice University Ca Foscari, Campo della Celestia 2737/b, I-30122 Venice (Italy)], E-mail: giovanni.libralato@unive.it; Losso, Chiara; Arizzi Novelli, Alessandra [Environmental Sciences Department, Venice University Ca Foscari, Campo della Celestia 2737/b, I-30122 Venice (Italy); Citron, Marta; Della Sala, Stefano; Zanotto, Emanuele [Environmental Department, Venice Port Authority, Zattere 1401, I-30123, Venice (Italy); Cepak, Franka [Institute of Public Health, Vojkovo nabrezje 4a, 6000 Koper (Slovenia); Volpi Ghirardini, Annamaria [Environmental Sciences Department, Venice University Ca Foscari, Campo della Celestia 2737/b, I-30122 Venice (Italy)

    2008-12-15

    This work assesses the ecotoxicological effects of polluted sediment after a decontamination treatment process using a new sediment washing technique. Sediment samples were collected from four sites in Marghera Port industrial channels (Venice, Italy). Ecotoxicological evaluations were performed with Vibrio fischeri and Crassostrea gigas bioassays. Whole sediment and elutriate were deemed as the most suitable environmental matrices for this study. Toxicity scores developed in the Lagoon of Venice for V. fischeri on whole sediment and for C. gigas on elutriate were considered for the final ranking of samples. Ecotoxicological results showed that the treated sediment samples presented both acute and sub-chronic toxicities, which were mainly attributed to the presence of some remaining chemicals such as metals and polyaromatic hydrocarbons. The acute toxicity ranged from low to medium, while the sub-chronic one from absent to very high, suggesting that treated sediments could not be reused in direct contact with seawater. - A sediment washing technique was assessed for port contaminated sediment remediation and reuse, indicating its reduced efficiency and the need for further improvements.

  6. Evaluation of in situ capping with clean soils to control phosphate release from sediments

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Di [State Key Laboratory of Lake Science and Environment, Nanjing Institute of Geography and Limnology, Chinese Academy of Sciences, Nanjing 210008 (China); Ding, Shiming, E-mail: smding@niglas.ac.cn [State Key Laboratory of Lake Science and Environment, Nanjing Institute of Geography and Limnology, Chinese Academy of Sciences, Nanjing 210008 (China); Sun, Qin [College of Environmental Science and Engineering, Hohai University, Nanjing (China); Zhong, Jicheng [State Key Laboratory of Lake Science and Environment, Nanjing Institute of Geography and Limnology, Chinese Academy of Sciences, Nanjing 210008 (China); Wu, Wei; Jia, Fei [College of Environmental Science and Engineering, Hohai University, Nanjing (China)

    2012-11-01

    Evaluation of in situ capping with clean soils to control phosphate release from the sediments of a eutrophic bay in Lake Taihu was performed after 18 months of capping. The concentrations of dissolved reactive phosphate (DRP) in pore waters and DRP resupply from native sediments and capped sediments were determined using high-resolution dialysis (HR-Peeper) and a Zr-oxide diffusive gradients in thin films (Zr-oxide DGT) technique. The adsorption isotherm of these sediments was further investigated using a modified Langmuir model. The results showed low concentrations of DRP in pore waters with a low resupply from the sediments for sustaining pore water DRP concentration after capping. The calculated flux to the overlying water following the capping treatment was approximately half of that for the native sediments, implying that the capping reduced the release of phosphate from the sediments. The low resupply of the sediments after capping was further demonstrated by larger partitioning coefficient (K{sub p}) values and greater adsorption capacity (Q{sub max}) values, while zero equilibrium concentrations (EPC{sub 0}s) were similar to those in native sediments. The larger K{sub p} and Q{sub max} were attributed to higher active Fe and Al introduced by the capping, indicating that the binding of phosphate onto the active Fe and Al played a critical role in reducing the internal loading of phosphorous. Highlights: Black-Right-Pointing-Pointer Evaluation of capping with soils was performed through high-resolution sampling. Black-Right-Pointing-Pointer Capping decreased the concentrations of DRP in pore waters and its release to waters. Black-Right-Pointing-Pointer Capping decreased the resupply of pore water DRP from the sediments. Black-Right-Pointing-Pointer Capped sediments had stronger abilities to adsorb and retain P. Black-Right-Pointing-Pointer Active Fe and Al introduced by capping played a critical role.

  7. Evaluation of in situ capping with clean soils to control phosphate release from sediments

    International Nuclear Information System (INIS)

    Xu, Di; Ding, Shiming; Sun, Qin; Zhong, Jicheng; Wu, Wei; Jia, Fei

    2012-01-01

    Evaluation of in situ capping with clean soils to control phosphate release from the sediments of a eutrophic bay in Lake Taihu was performed after 18 months of capping. The concentrations of dissolved reactive phosphate (DRP) in pore waters and DRP resupply from native sediments and capped sediments were determined using high-resolution dialysis (HR-Peeper) and a Zr-oxide diffusive gradients in thin films (Zr-oxide DGT) technique. The adsorption isotherm of these sediments was further investigated using a modified Langmuir model. The results showed low concentrations of DRP in pore waters with a low resupply from the sediments for sustaining pore water DRP concentration after capping. The calculated flux to the overlying water following the capping treatment was approximately half of that for the native sediments, implying that the capping reduced the release of phosphate from the sediments. The low resupply of the sediments after capping was further demonstrated by larger partitioning coefficient (K p ) values and greater adsorption capacity (Q max ) values, while zero equilibrium concentrations (EPC 0 s) were similar to those in native sediments. The larger K p and Q max were attributed to higher active Fe and Al introduced by the capping, indicating that the binding of phosphate onto the active Fe and Al played a critical role in reducing the internal loading of phosphorous. Highlights: ► Evaluation of capping with soils was performed through high-resolution sampling. ► Capping decreased the concentrations of DRP in pore waters and its release to waters. ► Capping decreased the resupply of pore water DRP from the sediments. ► Capped sediments had stronger abilities to adsorb and retain P. ► Active Fe and Al introduced by capping played a critical role.

  8. 210Pb dating of sediments from the central and the northern Adriatic Sea: The deposition and preservation of sedimentary organic carbon

    International Nuclear Information System (INIS)

    Hamilton, T.; Fowler, S.; Miquel, J.C.; La Rosa, J.

    1996-04-01

    A central goal of the ELNA project is to assess the carbon assimilation capacity of the Northern Adriatic Sea. This requires fundamental quantitative information on budgets and sinks of organic carbon. Any change in carbon production in the water column should be reflected in the underlying sediments. Moreover, the fraction of particulate organic carbon reaching the sea floor which is subsequently preserved in the sediment will be strongly coupled to sediment accumulation and mixing. In this study a series of box cores were collected in order to characterize a hypothetical eutrophication gradient extending from the Po River outflow region in the north down to the shallow meso-Adriatic depression (Jabuka Pit). The main tasks assigned to IAEA-MEL were to provide 210 Pb derived sedimentation and dry-mass accumulation rates and to examine the possible correlations between sedimentary processes, the deposition and preservation of sedimentary organic carbon and pelagic primary productivity

  9. State-of-the-practice : evaluation of sediment basin design, construction, maintenance, and inspection procedures.

    Science.gov (United States)

    2012-08-01

    The following document is the summary of results from a survey that was conducted to evaluate : the state-of-the-practice for sediment basin design, construction, maintenance, and inspection : procedures by State Highway Agencies (SHAs) across the na...

  10. Re-evaluating luminescence burial doses and bleaching of fluvial deposits using Bayesian computational statistics.

    NARCIS (Netherlands)

    Cunningham, A.C.; Wallinga, J.; Versendaal, Alice; Makaske, A.; Middelkoop, H.; Hobo, N.

    2015-01-01

    The optically stimulated luminescence (OSL) signal from fluvial sediment often contains a remnant from the previous deposition cycle, leading to a partially bleached equivalent-dose distribution. Although identification of the burial dose is of primary concern, the degree of bleaching could

  11. Re-evaluating luminescence burial doses and bleaching of fluvial deposits using Bayesian computational statistics

    NARCIS (Netherlands)

    Cunningham, A. C.; Wallinga, J.; Hobo, N.; Versendaal, A. J.; Makaske, B.; Middelkoop, H.

    2015-01-01

    The optically stimulated luminescence (OSL) signal from fluvial sediment often contains a remnant from the previous deposition cycle, leading to a partially bleached equivalent-dose distribution. Although identification of the burial dose is of primary concern, the degree of bleaching could

  12. Microbial methane in the shallow Paleozoic sediments and glacial deposits of Illinois, U.S.A.

    Science.gov (United States)

    Coleman, D.D.; Liu, Chao-Li; Riley, K.M.

    1988-01-01

    Methane formed by the microbial decomposition of buried organic matter is virtually ubiquitous in the groundwaters of Illinois. Chemical and carbon isotopic compositions are reported for gas samples collected from over 200 private and municipal water wells and from 39 small gas wells completed in glacial deposits (drift-gas wells). Carbon and hydrogen isotopic data for methane, carbon dioxide and water show that these gases were formed by the carbon dioxide reduction pathway, the same mechanism which has been previously shown to be responsible for microbial methane formation in the marine environment. The isotopic composition of methane in these samples can be closely correlated with the chemical composition of the gas and with water chemistry. The data are interpreted as indicating that isotopically very light methane is found in waters where the residence time of groundwater in the methanogenesis zone was very short relative to the methane production rate. ?? 1988.

  13. Short-term assessment of the sediment deposition rate and water conditions during a rainy season on La Azufrada coral reef, Gorgona Island, Colombia

    Directory of Open Access Journals (Sweden)

    Diego F. Lozano-Cortés

    2014-02-01

    Full Text Available One of the major stresses on corals is the settlement of suspended sediment on their surfaces. This leads to the blocking of light, the covering of the coral mucus surface and an increased risk of disease. For this reason sediment deposition on a reef is considered a highly important variable in coral reef studies. With the use of sediment traps and oceanographic sensors, the sediment deposition rate and water conditions during a rainy season (April-May 2009 on a Tropical Eastern Pacific coral reef (La Azufrada at Gorgona Island in Colombia were investigated. To quantify sediment deposition, sediment traps were established in nine stations along the coral reef (three stations per reef zone: backreef, flat and slope. To minimize disturbance by aquatic organisms in the sediment traps these were filled with hypersaline borax-buffered 10% formaline solution before their deployment; animals found in the filter contents were fixed and stored in a 4% formalin solution, frozen and identified in the laboratory. To determine the water conditions, discrete samples of water from 1 m and 10 m depths were collected using a Niskin bottle. Oceanographic variables (temperature, salinity and dissolved oxygen as well as turbidity, chlorophyll and nutrient concentration (nitrite, nitrate and phosphorus were measured in the samples from both depths. Vertical records of temperature and salinity were carried out with a Seabird-19 CTD nearest to La Azufrada and water transparency was measured using a Secchi disk. We found a mean trap collection rate of 23.30±4.34gm-2d-1 and did not detect a significant difference in the trap collection rate among reef zones. The mean temperature and salinity in the coral reef depth zone (0-10m layer were 26.98±0.19°C and 32.60±0.52, respectively. Fourteen taxonomic groups of invertebrates were detected inside the sediment traps with bivalves and copepods being the most abundant and frequen. The findings presented here constitute

  14. Short-term assessment of the sediment deposition rate and water conditions during a rainy season on La Azufrada coral reef, Gorgona Island, Colombia

    KAUST Repository

    Lozano-Cortés, Diego F

    2014-02-01

    One of the major stresses on corals is the settlement of suspended sediment on their surfaces. This leads to the blocking of light, the covering of the coral mucus surface and an increased risk of disease. For this reason sediment deposition on a reef is considered a highly important variable in coral reef studies. With the use of sediment traps and oceanographic sensors, the sediment deposition rate and water conditions during a rainy season (April-May 2009) on a Tropical Eastern Pacific coral reef (La Azufrada) at Gorgona Island in Colombia were investigated. To quantify sediment deposition, sediment traps were established in nine stations along the coral reef (three stations per reef zone: backreef, flat and slope). To minimize disturbance by aquatic organisms in the sediment traps these were filled with hypersaline borax-buffered 10% formaline solution before their deployment; animals found in the filter contents were fixed and stored in a 4% formalin solution, frozen and identified in the laboratory. To determine the water conditions, discrete samples of water from 1 m and 10 m depths were collected using a Niskin bottle. Oceanographic variables (temperature, salinity and dissolved oxygen) as well as turbidity, chlorophyll and nutrient concentration (nitrite, nitrate and phosphorus) were measured in the samples from both depths. Vertical records of temperature and salinity were carried out with a Seabird-19 CTD nearest to La Azufrada and water transparency was measured using a Secchi disk. We found a mean trap collection rate of 23.30±4.34gm-2d-1 and did not detect a significant difference in the trap collection rate among reef zones. The mean temperature and salinity in the coral reef depth zone (0-10m layer) were 26.98±0.19°C and 32.60±0.52, respectively. Fourteen taxonomic groups of invertebrates were detected inside the sediment traps with bivalves and copepods being the most abundant and frequen. The findings presented here constitute the first report

  15. Origin of stratiform sediment-hosted manganese carbonate ore deposits: Examples from Molango, Mexico, and TaoJiang, China

    Science.gov (United States)

    Okita, P.M.; Shanks, Wayne C.

    1992-01-01

    Carbonate and sulfide minerals from the Molango, Mexico, and TaoJiang, China, Mn deposits display similar and distinctive ??34S and ??13C patterns in intervals of manganese carbonate mineralization. ??13C-values for Mn-bearing carbonate range from -17.8 to +0.5??? (PDB), with the most negative values occurring in high-grade ore zones that are composed predominantly of rhodochrosite. In contrast, calcite from below, within and above Mn-carbonate zones at Molango has ??13C???0??? (PDB). Markedly negative ??13C data indicate that a large proportion of the carbon in Mn-carbonates was derived from organic matter oxidation. Diagenetic reactions using MnO2 and SO2-4 to oxidize sedimentary organic matter were the principle causes of such 12C enrichment. Pyrite content and sulfide ?? 34S-values also show distinctive variations. In unmineralized rocks, very negative ??34S-values (avg. < -21??? CDT) and abundant pyrite content suggest that pyrite formed from diagenetic, bacteriogenic sulfate reduction. In contrast, Mn-bearing horizons typically contain only trace amounts of pyrite (e.g., <0.5 wt% S with ??34S-values 34S-enriched, in some cases to nearly the value for contemporaneous seawater. 34S-enriched pyrite from the Mn-carbonate intervals indicates sulfide precipitation in an environment that underwent extensive SO2-4 reduction, and was largely a closed system with regard to exchange of sulfate and dissolved sulfide with normal seawater. The occasional occurrence of 34S-depleted pyrite within Mn-carbonate zones dominated by 34S-enriched pyrite is evidence that closed-system conditions were intermittent and limited to local pore waters and did not involve entire sedimentary basins. Mn-carbonate precipitation may have occluded porosity in the surficial sediments, thus establishing an effective barrier to SO2-4 exchange with overlying seawater. Similar isotopic and mineralogic characteristics from both the Molango and TaoJiang deposits, widely separated in geologic time and

  16. Reconstruction of eroded and deposited sediment volumes in the floodplains of the embanked River Waal, the Netherlands, for the period 1650 - 1850 AD

    Science.gov (United States)

    Hobo, Noortje; Makaske, Bart; Middelkoop, Hans

    2010-05-01

    The embanked floodplains of the River Waal developed as a result of stepwise downstream migration of meander bends between confining dykes. Accretion in the upstream limb of the outer bend - enhanced by groynes and trees - and erosion in the downstream limb have resulted in a series of successively developed sand bars, separated by secondary channels. On top of the sand bars and the secondary channel fills, fine-grained overbank sediments were deposited. Downstream migration ceased around 1850 AD, when the river bed was fixed by large-scale construction of groynes, and only overbank deposition continued. Eroded and deposited sediment volumes associated with downstream migration are affected by human activities. Goal of the present research is to estimate a sediment budget for a 12-km-long section along the River Waal, by quantifying the amount of erosion and deposition. We estimated these volumes for time slices of 50 years, between 1650 and 1850 AD, in order to be able to assess the variable impact of human interference during this period. To estimate erosion, we created geomorphological maps for all time slices, based on maps dating from the 17th century to present. In these maps, distinction is made between sand bars, residual channels, and older deposits (all sediments deposited before 1650 AD). Comparison between all maps allowed us to calculate the eroded area per time slice. Eroded volumes were hence estimated by multiplying the eroded area by the average river depth at that period, which is assumed to be the erosion depth. For estimation of deposition we used lithological cross-sections. These cross-sections are positioned such that every sand bar and every residual channel is represented in at least one cross-section. In every cross-section isochrones were drawn, based on OSL datings, chronologic interpretation of heavy metal profiles, and the historical maps. These isochrones are used to calculate the thickness of the sand bars, the residual channel fills

  17. Evaluating chemical extraction techniques for the determination of uranium oxidation state in reduced aquifer sediments

    Science.gov (United States)

    Stoliker, Deborah L.; Campbell, Kate M.; Fox, Patricia M.; Singer, David M.; Kaviani, Nazila; Carey, Minna; Peck, Nicole E.; Barger, John R.; Kent, Douglas B.; Davis, James A.

    2013-01-01

    Extraction techniques utilizing high pH and (bi)carbonate concentrations were evaluated for their efficacy in determining the oxidation state of uranium (U) in reduced sediments collected from Rifle, CO. Differences in dissolved concentrations between oxic and anoxic extractions have been proposed as a means to quantify the U(VI) and U(IV) content of sediments. An additional step was added to anoxic extractions using a strong anion exchange resin to separate dissolved U(IV) and U(VI). X-ray spectroscopy showed that U(IV) in the sediments was present as polymerized precipitates similar to uraninite and/or less ordered U(IV), referred to as non-uraninite U(IV) species associated with biomass (NUSAB). Extractions of sediment containing both uraninite and NUSAB displayed higher dissolved uranium concentrations under oxic than anoxic conditions while extractions of sediment dominated by NUSAB resulted in identical dissolved U concentrations. Dissolved U(IV) was rapidly oxidized under anoxic conditions in all experiments. Uraninite reacted minimally under anoxic conditions but thermodynamic calculations show that its propensity to oxidize is sensitive to solution chemistry and sediment mineralogy. A universal method for quantification of U(IV) and U(VI) in sediments has not yet been developed but the chemical extractions, when combined with solid-phase characterization, have a narrow range of applicability for sediments without U(VI).

  18. Gold and trace element zonation in pyrite using a laser imaging technique: Implications for the timing of gold in orogenic and carlin-style sediment-hosted deposits

    Science.gov (United States)

    Large, R.R.; Danyushevsky, L.; Hollit, C.; Maslennikov, V.; Meffre, S.; Gilbert, S.; Bull, S.; Scott, R.; Emsbo, P.; Thomas, H.; Singh, B.; Foster, J.

    2009-01-01

    Laser ablation ICP-MS imaging of gold and other trace elements in pyrite from four different sediment- hosted gold-arsenic deposits has revealed two distinct episodes of gold enrichment in each deposit: an early synsedimentary stage where invisible gold is concentrated in arsenian diagenetic pyrite along with other trace elements, in particular, As, Ni, Pb, Zn, Ag, Mo, Te, V, and Se; and a later hydrothermal stage where gold forms as either free gold grains in cracks in overgrowth metamorphic and/or hydrothermal pyrite or as narrow gold- arsenic rims on the outermost parts of the overgrowth hydrothermal pyrite. Compared to the diagenetic pyrites, the hydrothermal pyrites are commonly depleted in Ni, V, Zn, Pb, and Ag with cyclic zones of Co, Ni, and As concentration. The outermost hydrothermal pyrite rims are either As-Au rich, as in moderate- to high- grade deposits such as Carlin and Bendigo, or Co-Ni rich and As-Au poor as in moderate- to low-grade deposits such as Sukhoi Log and Spanish Mountain. The early enrichment of gold in arsenic-bearing syngenetic to diagenetic pyrite, within black shale facies of sedimentary basins, is proposed as a critical requirement for the later development of Carlin-style and orogenic gold deposits in sedimentary environments. The best grade sediment-hosted deposits appear to have the gold climax event, toward the final stages of deformation-related hydrothermal pyrite growth and fluid flow. ?? 2009 Society of Economic Geologists, Inc.

  19. Grain-size evolution in suspended sediment and deposits from the 2004 and 2008 controlled-flood experiments in Marble and Grand Canyons, Arizona

    Science.gov (United States)

    Draut, Amy E.; Topping, David J.; Rubin, David M.; Wright, Scott A.; Schmidt, John C.

    2010-01-01

    Since the closure of Glen Canyon Dam in 1963, the hydrology, sediment supply, and distribution and size of modern alluvial deposits in the Colorado River through Grand Canyon have changed substantially (e.g., Howard and Dolan, 1981; Johnson and Carothers, 1987; Webb et al., 1999; Rubin et al., 2002; Topping et al., 2000, 2003; Wright et al., 2005; Hazel et al., 2006). The dam has reduced the fluvial sediment supply at the upstream boundary of Grand Canyon National Park by about 95 percent. Regulation of river discharge by dam operations has important implications for the storage and redistribution of sediment in the Colorado River corridor. In the absence of natural floods, sediment is not deposited at elevations that regularly received sediment before dam closure. There has been a systemwide decrease in the size and number of subaerially exposed fluvial sand deposits since the 1960s, punctuated by episodic aggradation during the exceptional high-flow intervals in the early 1980s and by sediment input from occasional tributary floods (Beus and others, 1985; Schmidt and Graf, 1990; Kearsley et al., 1994; Schmidt et al., 2004; Wright et al., 2005; Hazel et al., 2006). Fluvial sandbars are an important component of riparian ecology that, among other functions, enclose eddy backwaters that form native-fish habitat, provide a source for eolian sand that protects some archaeological sites, and are used as campsites by thousands of river-runners annually (Rubin et al., 1990; Kearsley et al., 1994; Neal et al., 2000; Wright et al., 2005; Draut and Rubin, 2008).

  20. GEOLOGY AND DEPOSITIONAL ENVIRONMENT OF CAMPANO-MAASTRICHTIAN SEDIMENTS IN THE ANAMBRA BASIN, SOUTHEASTERN NIGERIA: EVIDENCE FROM FIELD RELATIONSHIP AND SEDIMENTOLOGICAL STUDY

    Directory of Open Access Journals (Sweden)

    A. E Salufu

    2009-12-01

    Full Text Available The study area lies within the Anambra Basin and it is made up of Enugu Shale, Mamu Formation, Ajali Sandstone, and Nsukka Formation. This study aimed at determining the geology and depositional environmental of these formations through field relationship and grain size distribution morphologic studies.The field data shows Enugu Shale as fissile, light grey with extraformational clast which graded into Mamu Formation whichis made up of shale, coal and sandy shale. It passes upward into Ajali Sandstone which is characterized by cross beds, Herringbonestructures and Ophiomorpha burrows. The youngest formation within the basin is Nsukka Formation.The granulometric study of Mamu Formation shows fine to medium grains, coarse, medium to fine grain for Mamu and Ajali Formation respectively. The standard deviation indicates poorly sorted. The kurtosis shows leptokurtic, platykurtic to very leptokurtic for both while the skewness values indicate positive and symmetrical in all except for Ajali Sandstone that is negatively skewed.The bivariate and the multivariate results reveal shallow marine and fluvial deposits for both Mamu Formation and Ajali Sandstone respectively. The paleocurrent direction of Ajali Sandstone indicates southwest while the provenance is northeast.The fissility of Enugu Shale suggests that it was deposited in low energy environment, distal to proximal lagoon environment.The presence of extraformatonal clast within Enugu Shale indicates fluvial incursion. However, the textural analysis of Mamu Formation suggests a sediment deposited in a low energy environment which favoured deposition of fine to medium size sediments that is, estuary environment. Textural result of Ajali Sandstone in the study area coupled with the field data such as Herring-bone structures, and Ophiomorpha burrows, revealed that Ajali Sandstone was deposited in a tidal environment probably littoral environment. While the light grey colour observed in the

  1. Evaluation of the efficiency of some sediment trapping methods after a Mediterranean forest fire.

    Science.gov (United States)

    Fox, D M

    2011-02-01

    Forest fires are common in Mediterranean environments and may become increasingly more frequent as the climate changes. Destruction of the forest cover and litter layer leads to greater overland flow and increased erosion rates. The greatest risk occurs during the first rainstorms following a major fire, so local authorities must act quickly to put erosion control methods in place in order to avoid excessive post-fire sediment loads in river channels. Deciding on which methods to use requires accurate knowledge of their impact on sediment load and an estimate of their cost efficiency. The objective of this study was to evaluate the efficiency of Log Debris Dams (LDDs) and a sedimentation basin for their effectiveness in trapping sediments. Paired sub-catchments were studied to quantify the amount of sediments trapped in stream channels by a series of LDDs and a sedimentation basin. Cost efficiency was evaluated for each of the measures as a function of the cost per unit volume of sediments trapped. In addition, grain size analyses were performed to characterise the nature of the sediments trapped. A third sediment trapping method, Log Erosion Barriers (LEBs) was evaluated more superficially than the first two and conclusions regarding this method are tentative. LDDs trapped a mean volume of 1.57 m³ per unit (median=1.28 m³); mean LDD height was 105.4 cm (std. dev.=21.9 cm), and mean height of trapped sediments was only 50.0 cm (std. dev.=22.9 cm), showing that the traps were only half filled. Sediment height was limited by the presence of gaps between logs or branches that allowed runoff to flow through. Comparison of the textural characteristics of slope and trapped sediments showed distinct sorting: particles greater than 20mm were not mobilised from the slopes during the study period, sediments in the medium to coarse sand size fractions were trapped preferentially by the LDDs, and sediments in the sedimentation basin were enriched by clay and silt sized

  2. Kankakee River Basin: Evaluation of Sediment Management Strategies

    Science.gov (United States)

    2013-09-01

    basin, and development of a SIAM model from an existing US Army Corps of Engineers Hydrologic Engineering Center, River Analysis System ( HEC - RAS ...4 SIAM Model A SIAM model was developed from an existing calibrated HEC - RAS model provided by the Rock Island District. The limits of the HEC - RAS ...model are shown in Figure 4.1. No further effort was made to verify the calibration of the HEC - RAS model. The estimated sediment loads were used to

  3. Mio Pliocene volcaniclastic deposits in the Famatina Ranges, southern Central Andes: A case of volcanic controls on sedimentation in broken foreland basins

    Science.gov (United States)

    Martina, Federico; Dávila, Federico M.; Astini, Ricardo A.

    2006-04-01

    A well-constrained record of Miocene-Pliocene explosive volcanism is preserved within the broken foreland of Western Argentina along the Famatina Ranges. This paper focuses on the volcaniclastic record known as the Río Blanco member of the El Durazno Formation. Three facies can be recognized in the study area: (1) massive tuffs; (2) volcaniclastic conglomerates and (3) pumiceous sandstones. These facies are interpreted as primary pyroclastic flow deposits (ignimbrites) and reworked volcanogenic deposits within interacting volcanic-fluvial depositional systems. Alternation between ignimbrites and volcanogenic sandstones and conglomerates suggest a recurrent pattern of sedimentation related to recurrent volcanic activity. Considering the facies mosaic and relative thicknesses of facies, short periods of syn-eruption sedimentation (volcaniclastic deposits) seem to have been separated by longer inter-eruption periods, where normal stream-flow processes were dominant. The volcaniclastic component decreases up-section, suggesting a gradual reduction in volcanic activity. The mean sedimentation rate of the Río Blanco member is higher (0.44 mm/year) than those obtained for the underlying and overlying units. This increase cannot be fully explained by foreland basement deformation and tectonic loading. Hence, we propose subsidence associated with volcanic activity as the causal mechanism. Volcanism would have triggered additional accommodation space through coeval pyroclastic deposition, modification of the stream equilibrium profile, flexural loading of volcanoes, and thermal processes. These mechanisms may have favored the preservation of volcaniclastic beds in the high-gradient foreland system of Famatina during the Mio-Pliocene. Thus, the Río Blanco member records the response of fluvial systems to large, volcanism-induced sediment loads.

  4. Data management for evaluation of deposits at Nuclebras

    International Nuclear Information System (INIS)

    Da Vinha, C.A.G.; Garcia Guerra, P.A.

    1980-01-01

    The large volume of data generated in any deposit evaluation work based on information obtained from intensive drilling operations and produced by different types of equipment involved in prospecting calls for the establishment and use of standardized and unified systems of data collection. Thus, standardization of data collection and electronic data processing must be ensured if the management of such data is to be viable, i.e. effective from the technical and economic points of view. These two considerations form the basis of the Nuclebras data management system, in which essential data are collected and processed by means of sub-systems called Catalogue of Samples, Drilling Report and Application Programmes, thus providing the basis for conventional statistical and geostatistical evaluations. It should also be noted that new data to be generated at the subsequent stages of planning and mining control will be added to this core, so that it has to be sufficiently flexible and generic to be used in the long term for a wide variety of purposes. (author)

  5. Evaluation of instruments used in particle size analysis by using the sedimentation technique

    International Nuclear Information System (INIS)

    Elmasry, M.A.A.; Abdrahman, A.A.M.; Ahmed, A.Z.

    2007-01-01

    This study is carried out to evaluate the performance of some instruments in which the sedimentation technique is used for the determination of particle size distribution using Stoke's law. A mathematical formula has been developed to calculate the particle size distribution for different cases and the results were compared to the real ones. The results revealed unsatisfactory agreement between the calculated and the measured values. In addition, illogic results were obtained indicating that the instruments in which the sedimentation technique is used are not the proper ones to provide accurate measurements except for mono particle size cases. More above, the results obtained represent the sedimentation rate but not the particle size distribution.

  6. Role of urban surface roughness in road-deposited sediment build-up and wash-off

    Science.gov (United States)

    Zhao, Hongtao; Jiang, Qian; Xie, Wenxia; Li, Xuyong; Yin, Chengqing

    2018-05-01

    Urban road surface roughness is one of the most important factors in estimation of surface runoff loads caused by road-deposited sediment (RDS) wash-off and design of its control measures. However, because of a lack of experimental data to distinguish the role of surface roughness, the effects of surface roughness on RDS accumulation and release are not clear. In this study, paired asphalt and concrete road surfaces and rainfall simulation designs were used to distinguish the role of surface roughness in RDS build-up and wash-off. Our results showed that typical asphalt surfaces often have higher depression depths than typical concrete surfaces, indicating that asphalt surfaces are relatively rougher than concrete surface. Asphalt surfaces can retain a larger RDS amount, relative higher percentage of coarser particles, larger RDS wash-off loads, and lower wash-off percentage, than concrete surfaces. Surface roughness has different effects in RDS motilities with different particle sizes during rainfall runoff, and the settleable particles (44-149 μm) were notably influenced by it. Furthermore, the first flush phenomenon tended to be greater on relatively smooth surfaces than relatively rough surfaces. Overall, surface roughness plays an important role in influencing the complete process of RDS build-up and wash-off on different road characteristics.

  7. An earth system model for evaluation of dry deposition

    Energy Technology Data Exchange (ETDEWEB)

    Arritt, R.W. [Iowa State Univ., Ames, IA (United States)

    1994-12-31

    A coupled model of atmosphere, soil, and vegetation showed that interactions among the various components can have important effects on dry deposition of SO{sub 2}. In particular, dry soil (near or below the wilting point) leads to an increase of stomatal resistance and a decrease in deposition. Once the soil moisture is at least twice the wilting point, the model results indicate that additional moisture has little effect on the accumulated daytime dry deposition.

  8. Qualitative assessment of selected areas of the world for undiscovered sediment-hosted stratabound copper deposits: Chapter Y in Global mineral resource assessment

    Science.gov (United States)

    Zientek, Michael L.; Wintzer, Niki E.; Hayes, Timothy S.; Parks, Heather L.; Briggs, Deborah A.; Causey, J. Douglas; Hatch, Shyla A.; Jenkins, M. Christopher; Williams, David J.; Zientek, Michael L.; Hammarstrom, Jane M.; Johnson, Kathleen M.

    2015-12-14

    A qualitative mineral resource assessment of sediment-hosted stratabound copper mineralized areas for undiscovered copper deposits was performed for 10 selected areas of the world. The areas, in alphabetical order, are (1) Belt-Purcell Basin, United States and Canada; (2) Benguela and Cuanza Basins, Angola; (3) Chuxiong Basin, China; (4) Dongchuan Group rocks, China; (5) Egypt–Israel–Jordan Rift, Egypt, Israel, and Jordan; (6) Maritimes Basin, Canada; (7) Neuquén Basin, Argentina; (8) Northwest Botswana Rift, Botswana and Namibia; (9) Redstone Copperbelt, Canada; and (10) Salta Rift System, Argentina. This assessment (1) outlines the main characteristics of the areas, (2) classifies known deposits by deposit model subtypes, and (3) ranks the areas according to their potential to contain undiscovered copper deposits.

  9. The deposition - a modern phenomenon in the evaluation of inhalation risk of mining aerosols

    Directory of Open Access Journals (Sweden)

    Ľubomír Legáth

    2007-04-01

    Full Text Available The deposition is defined as an array of processes causing a part of the inhaled aerosol to remain (after its expiration in the respiratory tract. The particles retained in the respiratory tract are called deposits. The deposition encompasses of three different mechanisms: impaction, sedimentation and Brown molecular movement combined with the diffusion. The impaction remains the most potential contribution to the deposition in the conductive zone of the respiratory tract. While the sedimentation and diffusion in conjunction with the Brown molecular movement have a major impact in the respiratory area with the zero flow movement. The above listed mechanisms participate with the different ratio to the deposition at respective parts of the respiratory tract.The deposition depends on physical and chemical properties of inhaled aerosols as well as on the susceptibility of each individual. The size, shape, mass, and electric charges are among the basic characteristics of aerosols. The individual susceptibility is mainly influenced by an anatomical arrangement of respiratory tract, tidal volume, frequency of breathing, and breath holding.

  10. Texture, mineralogy and geochemistry of the continental slope sediments in front of Los Tuxtlas, Gulf of Mexico, Mexico: implications on weathering, origin and depositional environments

    Science.gov (United States)

    Marca-Castillo, M. E.; Armstrong-Altrin, J.

    2017-12-01

    The textural analysis, mineralogy and geochemistry of two sediment cores recovered from the deep water zone of the southwestern part of the Gulf of Mexico ( 1666 and 1672 m water depth) were studied to infer the provenance and depositional behavior. The textural analysis revealed that both cores are dominated by silt, which occupy more than 50% in both samples and the clay occupy 40%. The petrographic analysis revealed remains of biogenic origin sediments and lithic fragments with an angular shape and low sphericity, indicating a low energy environment and therefore a low level of weathering in the sediment, which suggests that the sediments were not affected by transport and derived from a nearby source rock. In both cores quartz fragments were identified; also volcanic lithic and pyroxenes fragments, which are rocks of intermediate composition and are generally associated with the volcanic activity of the continental margins. SEM-EDS studies showed that the analysed samples have concentrations of minerals such as barite, gibbsite, kaolinite, grossular, magnetite, plagioclase and chlorite, which are probably derived from the mainland to the deep sea zone. In the trace element analysis it was observed a low Sc content, while Co, Ni, V and Cu are slightly enriched with respect to the upper continental crust; this enrichment is related to sediments from intermediate sources. The sediments are classified as shale in the log (SiO2 / Al2O3) - log (Fe2O / K2O) diagram. The fine particles of the shale indicate that a deposit occurred as a result of the gradual sedimentation due to relatively non-turbulent currents, which is consistent with the petrographic analysis. The geochemical features of major and trace elements suggest sediments were derived largely from the natural andesite erosion of coastal regions along the Gulf of Mexico. High values of Fe2O3 and MnO are observed in the upper intervals, reflecting the influence of volcanic sediments. The major element

  11. Evaluation of 10 cross-shore sediment transport morphological models

    CSIR Research Space (South Africa)

    Schoonees, JS

    1995-05-01

    Full Text Available .S. Schoonees, A.K. Theron/Coastal Engineering 25 (1995) 141 11 0.99 m sediment build-up or beach profile...

  12. Impaired Short-Term Functioning of a Benthic Community from a Deep Norwegian Fjord Following Deposition of Mine Tailings and Sediments

    Directory of Open Access Journals (Sweden)

    Lisa Mevenkamp

    2017-05-01

    Full Text Available The extraction of minerals from land-based mines necessitates the disposal of large amounts of mine tailings. Dumping and storage of tailings into the marine environment, such as fjords, is currently being performed without knowing the potential ecological consequences. This study investigated the effect of short-term exposure to different deposition depths of inert iron ore tailings (0.1, 0.5, and 3 cm and dead subsurface sediment (0.5 and 3 cm on a deep water (200 m fjord benthic assemblage in a microcosm experiment. Biotic and abiotic variables were measured to determine structural and functional changes of the benthic community following an 11 and 16 day exposure with tailings and dead sediment, respectively. Structural changes of macrofauna, meiofauna, and bacteria were measured in terms of biomass, density, community composition and mortality while measures of oxygen penetration depth, sediment community oxygen consumption and 13C-uptake and processing by biota revealed changes in the functioning of the system. Burial with mine tailings and natural sediments modified the structure and functioning of the benthic community albeit in a different way. Mine tailings deposition of 0.1 cm and more resulted in a reduced capacity of the benthic community to remineralize fresh 13C-labeled algal material, as evidenced by the reduced sediment community oxygen consumption and uptake rates in all biological compartments. At 3 cm of tailings deposition, it was evident that nematode mortality was higher inside the tailings layer, likely caused by reduced food availability. In contrast, dead sediment addition led to an increase in oxygen consumption and bacterial carbon uptake comparable to control conditions, thereby leaving deeper sediment layers anoxic and in turn causing nematode mortality at 3 cm deposition. This study clearly shows that even small levels (0.1 cm of instantaneous burial by mine tailings may significantly reduce benthic ecosystem

  13. Syn-eruptive, soft-sediment deformation of deposits from dilute pyroclastic density current: triggers from granular shear, dynamic pore pressure, ballistic impacts and shock waves

    Science.gov (United States)

    Douillet, G. A.; Taisne, B.; Tsang-Hin-Sun, E.; Muller, S. K.; Kueppers, U.; Dingwell, D. B.

    2015-05-01

    Soft-sediment deformation structures can provide valuable information about the conditions of parent flows, the sediment state and the surrounding environment. Here, examples of soft-sediment deformation in deposits of dilute pyroclastic density currents are documented and possible syn-eruptive triggers suggested. Outcrops from six different volcanoes have been compiled in order to provide a broad perspective on the variety of structures: Soufriere Hills (Montserrat), Tungurahua (Ecuador), Ubehebe craters (USA), Laacher See (Germany), and Tower Hill and Purrumbete lakes (both Australia). The variety of features can be classified in four groups: (1) tubular features such as pipes; (2) isolated, laterally oriented deformation such as overturned or oversteepened laminations and vortex-shaped laminae; (3) folds-and-faults structures involving thick (>30 cm) units; (4) dominantly vertical inter-penetration of two layers such as potatoids, dishes, or diapiric flame-like structures. The occurrence of degassing pipes together with basal intrusions suggest fluidization during flow stages, and can facilitate the development of other soft-sediment deformation structures. Variations from injection dikes to suction-driven, local uplifts at the base of outcrops indicate the role of dynamic pore pressure. Isolated, centimeter-scale, overturned beds with vortex forms have been interpreted to be the signature of shear instabilities occurring at the boundary of two granular media. They may represent the frozen record of granular, pseudo Kelvin-Helmholtz instabilities. Their recognition can be a diagnostic for flows with a granular basal boundary layer. Vertical inter-penetration and those folds-and-faults features related to slumps are driven by their excess weight and occur after deposition but penecontemporaneous to the eruption. The passage of shock waves emanating from the vent may also produce trains of isolated, fine-grained overturned beds that disturb the surface bedding

  14. Evaluating competition in the loan and deposit market using the ...

    African Journals Online (AJOL)

    Competition was more intense in the market for loans than in the deposit market. There was more competition among domestic banks than among foreign banks. The study also reveals that there was marginal differences in the intensity of competition for loans and deposits among domestic banks. On the aggregate level, ...

  15. Sedimentary record of polycyclic aromatic hydrocarbons in a sediment core from a maar lake, Northeast China: evidence in historical atmospheric deposition.

    Science.gov (United States)

    Guan, Yu-Feng; Sun, Jian-Lin; Ni, Hong-Gang; Guo, Jian-Yang

    2012-09-01

    A maar lake is an excellent ecosystem to study the atmospheric deposition of pollutants, as its contaminants are primarily by atmospheric deposition. In this study, a sediment core from Sihailongwan Maar Lake, Northeast China, was collected and the historical atmospherically deposited polycyclic aromatic hydrocarbons (PAHs) were analyzed. The concentrations of TPAHs (the sum of the US EPA proposed 16 priority PAHs, excluding naphthalene and pyrene) ranged from 473.9 to 2289 ng g(-1) with a slow increasing stage in the deeper sediments and a sharp increasing stage in the upper sediments. The input rate of TPAHs, especially that of PAH(9) (the sum of fluoranthene, benzo(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, dibenzo(ah)anthrathene, and benzo(ghi)perylene), correlated well to the Chinese historical socioeconomic data. This indicates that sediment PAHs were mainly derived from human activities and PAH(9) can be regarded as a better indicator of the local socioeconomic development. Source identification suggested that PAHs were originated primarily from mixed sources (e.g., coal and biomass burning and petroleum combustion), except for perylene which was mostly of diagenetic origin. In addition, the down-core PAHs profile clearly illustrated that PAHs sources in Northeast China experienced a transformation from low- and moderate temperature to high-temperature combustion processes, especially after the late 1980s. Additionally, an ecological risk assessment using two redefined biological thresholds (TEQ(ERL) and TEQ(ERM)) indicated that most of the PAHs measured in the present sediment core would not cause an immediate toxic effect; only FLU and PHEN are a potential source of concern for biological impairment.

  16. Heavy metal contents of road-deposited sediment along the urban-rural gradient around Beijing and its potential contribution to runoff pollution.

    Science.gov (United States)

    Zhao, Hongtao; Li, Xuyong; Wang, Xiaomei

    2011-09-01

    Understanding the contribution of road-deposited sediment (RDS) and its washoff process is essential for controlling urban runoff pollution. Ninety-seven RDS samples were collected along the urban-suburban-rural gradient from areas of five administrative units in the Beijing metropolitan region, including central urban (UCA), urban village (UVA), central suburban county (CSA), rural town (RTA), and rural village (RVA) areas. RDS washoff was evaluated with different particle sizes using a rainfall simulator. Heavy metal elements (i.e., Cr, Cu, Ni, Pb, and Zn) were estimated in both RDS and runoff samples. The RDS mass per unit area increased in the order UCA (21 ± 24 g/m(2)) ≈ CSA (20 ± 16 g/m(2)) runoff pollution contributions per unit area. Our findings imply that controlling the first flush in the UCA and CSA, and improving existing street cleaning methods and road surface conditions in the TRA, UVA, and RVA will be appropriate strategies for controlling runoff pollution from RDS.

  17. Evaluating Regime Change of Sediment Transport in the Jingjiang River Reach, Yangtze River, China

    Directory of Open Access Journals (Sweden)

    Li He

    2018-03-01

    Full Text Available The sediment regime in the Jingjiang river reach of the middle Yangtze River has been significantly changed from quasi-equilibrium to unsaturated since the impoundment of the Three Gorges Dam (TGD. Vertical profiles of suspended sediment concentration (SSC and sediment flux can be adopted to evaluate the sediment regime at the local and reach scale, respectively. However, the connection between the vertical concentration profiles and the hydrologic conditions of the sub-saturated channel has rarely been examined based on field data. Thus, vertical concentration data at three hydrological stations in the reach (Zhicheng, Shashi, and Jianli are collected. Analyses show that the near-bed concentration (within 10% of water depth from the riverbed may reach up to 15 times that of the vertical average concentration. By comparing the fractions of the suspended sediment and bed material before and after TGD operation, the geomorphic condition under which the distinct large near-bed concentrations occur have been examined. Based on daily discharge-sediment hydrographs, the reach scale sediment regime and availability of sediment sources are analyzed. In total, remarkable large near-bed concentrations may respond to the combination of wide grading suspended particles and bed material. Finally, several future challenges caused by the anomalous vertical concentration profiles in the unsaturated reach are discussed. This indicates that more detailed measurements or new measuring technologies may help us to provide accurate measurements, while a fractional dispersion equation may help us in describing. The present study aims to gain new insights into regime change of sediment suspension in the river reaches downstream of a very large reservoir.

  18. Post-depositional redistribution of trace metals in reservoir sediments of a mining/smelting-impacted watershed (the Lot River, SW France)

    International Nuclear Information System (INIS)

    Audry, Stephane; Grosbois, Cecile; Bril, Hubert; Schaefer, Joerg; Kierczak, Jakub; Blanc, Gerard

    2010-01-01

    Mining/smelting wastes and reservoir sediment cores from the Lot River watershed were studied using mineralogical (XRD, SEM-EDS, EMPA) and geochemical (redox dynamics, selective extractions) approaches to characterize the main carrier phases of trace metals. These two approaches permitted determining the role of post-depositional redistribution processes in sediments and their effects on the fate and mobility of trace metals. The mining/smelting wastes showed heterogeneous mineral compositions with highly variable contents of trace metals. The main trace metal-bearing phases include spinels affected by secondary processes, silicates and sulfates. The results indicate a clear change in the chemical partitioning of trace metals between the reservoir sediments upstream and downstream of the mining/smelting activities, with the downstream sediments showing a 2-fold to 5-fold greater contribution of the oxidizable fraction. This increase was ascribed to stronger post-depositional redistribution of trace metals related to intense early diagenetic processes, including dissolution of trace metal-bearing phases and precipitation of authigenic sulfide phases through organic matter (OM) mineralization. This redistribution is due to high inputs (derived from mining/smelting waste weathering) at the water-sediment interface of (i) dissolved SO 4 promoting more efficient OM mineralization, and (ii) highly reactive trace metal-bearing particles. As a result, the main trace metal-bearing phases in the downstream sediments are represented by Zn- and Fe-sulfides, with minor occurrence of detrital zincian spinels, sulfates and Fe-oxyhydroxides. Sequestration of trace metals in sulfides at depth in reservoir sediments does not represent long term sequestration owing to possible resuspension of anoxic sediments by natural (floods) and/or anthropogenic (dredging, dam flush) events that might promote trace metal mobilization through sulfide oxidation. It is estimated that, during a major

  19. Applications of dendrochronology and sediment geochronology to establish reference episodes for evaluations of environmental radioactivity

    Energy Technology Data Exchange (ETDEWEB)

    Waugh, W.J.; Carroll, J.; Abraham, J.D.; Landeen, D.S. [Roy F. Weston, Inc., U.S. Department of Energy, Grand Junction Office, 2597 B 3/4 Road, Grand Junction, CO 81503 (United States)

    1998-12-01

    Dendrochronology and sediment geochronology have been used to demonstrate retrospective monitoring of environmental radioactivity at United States Department of Energy (DOE) sites. {sup 14}C in annual growth rings of sagebrush preserved the temporal and spatial patterns of {sup 14}C resulting from dispersion downwind of a nuclear fuel processing facility at the Hanford Site in Washington State. As far as 10 km downwind of the facility, {sup 14}C concentrations were significantly higher in growth rings formed during a fuel processing episode than in rings produced during preoperational or postoperational episodes. An episode of uranium mill tailings deposition in pond sediments at the Grand Junction Office in Colorado was reconstructed using {sup 210}Pb geochronology constrained by a marker of peak {sup 137}Cs fallout. Uranium concentrations in ponds sediments deposited after the processing episode provide a reasonable cleanup standard. These reference episodes of environmental radioactivity reconstructed from measurements taken within contaminated environments can improve or replace reference area data as baseline information for dose reconstructions, risk assessments, and the establishment of cleanup standards. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

  20. Applications of dendrochronology and sediment geochronology to establish reference episodes for evaluations of environmental radioactivity

    International Nuclear Information System (INIS)

    Waugh, W.J.; Carroll, J.; Abraham, J.D.; Landeen, D.S.

    1998-01-01

    Dendrochronology and sediment geochronology have been used to demonstrate retrospective monitoring of environmental radioactivity at United States Department of Energy (DOE) sites. 14 C in annual growth rings of sagebrush preserved the temporal and spatial patterns of 14 C resulting from dispersion downwind of a nuclear fuel processing facility at the Hanford Site in Washington State. As far as 10 km downwind of the facility, 14 C concentrations were significantly higher in growth rings formed during a fuel processing episode than in rings produced during preoperational or postoperational episodes. An episode of uranium mill tailings deposition in pond sediments at the Grand Junction Office in Colorado was reconstructed using 210 Pb geochronology constrained by a marker of peak 137 Cs fallout. Uranium concentrations in ponds sediments deposited after the processing episode provide a reasonable cleanup standard. These reference episodes of environmental radioactivity reconstructed from measurements taken within contaminated environments can improve or replace reference area data as baseline information for dose reconstructions, risk assessments, and the establishment of cleanup standards. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

  1. Evaluating the provenance of fine sediment in degraded Freshwater Pearl Mussel habitats.

    Science.gov (United States)

    Blake, Will; Haley, Steve; Goddard, Rupert; Stone, Peter; Broadhead, Kat

    2015-04-01

    Freshwater Pearl Mussels (FWPM), Margaritifera margaritifera, are among the most critically threatened freshwater bivalves worldwide. In addition to their important roles in particle processing, nutrient release, and sediment mixing, they also serve as an ideal target species for evaluation of aquatic ecosystem functioning especially in the context of their symbiotic relationship with Atlantic salmon Salmo salar and brown or sea trout Salmo trutta. Poor water quality, particularly eutrophication, and siltation are considered major contributory factors in the decline of the species hence management of diffuse water pollution from agriculture (DWPA) is a key priority in catchments that host FWPM habitats. Against this background, this study adopted a combined monitoring, surveying and sediment fingerprinting approach to determine the principal sources of fine sediment impacting FWPM habitats in the River Clun, a Special area of Conservation (SAC) for FWPMs in central western UK. Potential sediment production hotspot areas in the ca 200 km2 catchment area upstream of FWPM habitats were initially evaluated using the SCIMAP risk mapping tool. Suspended sediment monitoring was undertaken on the main stem channel where FWPM habitats are located and wet weather catchment walkover surveys undertaken along the upstream river and stream network. Within this monitoring framework, sediment fingerprinting was undertaken at two levels. The first level aimed to link primary catchment sources (cultivated and uncultivated soil, channel bank erosion, and material transported via roads and tracks) to suspended sediment output from each main tributary upstream of the FWPM beds. The second level linked silt in the FWMP beds to the main tributaries, as integrated source end-members, with the inclusion of main channel bank erosion, a notable feature of walkover surveys as an additional source. Geochemical fingerprints, determined by XRF spectroscopy, were dominated by conservative mineral

  2. Influence of low impact development construction on pollutant process of road-deposited sediments and associated heavy metals.

    Science.gov (United States)

    Ma, Yukun; Gong, Manli; Zhao, Hongtao; Li, Xuyong

    2018-02-01

    Intense Low-Impact Development (LID) construction in China could lead to increasingly severe stormwater and receiving water pollution due to the lack of appropriate regulation for mitigating pollution from LID construction. Samples of road-deposited sediments (RDS) were collected from 50 study sites at seven LID construction stages and four road hierarchies to analyze the pollution process and determine the size of the region influenced by LID construction. Six heavy metals were analyzed, and the RDS index model was adopted to estimate the potential heavy metal load washed off by stormwater runoff. Analysis of variance revealed that the excavation and gravel filling of rain gardens and excavation of porous pavements were critical LID construction stages that contributed the largest masses of RDS per unit area to road surfaces. Although the concentration of heavy metals at LID construction sites was lower than at sites without LID construction, the load of heavy metals washed off from LID construction was much higher. In addition, the sizes of regions influenced by accumulated RDS from LID construction descended in the following order: arterial road (600-775m)>collector road (150-200m)>access road (100-150m)>laneway (20-30m). According to the characteristics of LID construction at the study sites, the potential total solid loads in stormwater throughout China were estimated to reach 36,694t by 2020 and 146,777t by 2030. According to the results of analysis, several recommendations are provided for designing LID construction regulations to mitigate stormwater pollution. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Laboratory evaluation of the Sequoia Scientific LISST-ABS acoustic backscatter sediment sensor

    Science.gov (United States)

    Snazelle, Teri T.

    2017-12-18

    Sequoia Scientific’s LISST-ABS is an acoustic backscatter sensor designed to measure suspended-sediment concentration at a point source. Three LISST-ABS were evaluated at the U.S. Geological Survey (USGS) Hydrologic Instrumentation Facility (HIF). Serial numbers 6010, 6039, and 6058 were assessed for accuracy in solutions with varying particle-size distributions and for the effect of temperature on sensor accuracy. Certified sediment samples composed of different ranges of particle size were purchased from Powder Technology Inc. These sediment samples were 30–80-micron (µm) Arizona Test Dust; less than 22-µm ISO 12103-1, A1 Ultrafine Test Dust; and 149-µm MIL-STD 810E Silica Dust. The sensor was able to accurately measure suspended-sediment concentration when calibrated with sediment of the same particle-size distribution as the measured. Overall testing demonstrated that sensors calibrated with finer sized sediments overdetect sediment concentrations with coarser sized sediments, and sensors calibrated with coarser sized sediments do not detect increases in sediment concentrations from small and fine sediments. These test results are not unexpected for an acoustic-backscatter device and stress the need for using accurate site-specific particle-size distributions during sensor calibration. When calibrated for ultrafine dust with a less than 22-µm particle size (silt) and with the Arizona Test Dust with a 30–80-µm range, the data from sensor 6039 were biased high when fractions of the coarser (149-µm) Silica Dust were added. Data from sensor 6058 showed similar results with an elevated response to coarser material when calibrated with a finer particle-size distribution and a lack of detection when subjected to finer particle-size sediment. Sensor 6010 was also tested for the effect of dissimilar particle size during the calibration and showed little effect. Subsequent testing revealed problems with this sensor, including an inadequate temperature

  4. Fabrication and evaluation of chemically vapor deposited tungsten heat pipe.

    Science.gov (United States)

    Bacigalupi, R. J.

    1972-01-01

    A network of lithium-filled tungsten heat pipes is being considered as a method of heat extraction from high temperature nuclear reactors. The need for material purity and shape versatility in these applications dictates the use of chemically vapor deposited (CVD) tungsten. Adaptability of CVD tungsten to complex heat pipe designs is shown. Deposition and welding techniques are described. Operation of two lithium-filled CVD tungsten heat pipes above 1800 K is discussed.

  5. U-Pb Detrital Zircon Geochronologic Constraints on Depositional Age and Sediment Source Terrains of the Late Paleozoic Tepuel-Genoa Basin

    Science.gov (United States)

    Griffis, N. P.; Montanez, I. P.; Isbell, J.; Gulbranson, E. L.; Wimpenny, J.; Yin, Q. Z.; Cúneo, N. R.; Pagani, M. A.; Taboada, A. C.

    2014-12-01

    The late Paleozoic Ice Age (LPIA) is the longest-lived icehouse of the Phanerozoic and the only time a metazoan dominated and vegetated world transitioned from an icehouse climate into a greenhouse. Despite several decades of research, the timing, extent of glaciation and the location of ice centers remain unresolved, which prohibits reconstruction of ice volume. The Permo-Carboniferous sediments in the Tepuel-Genoa Basin, Patagonia contains a near complete record of sedimentation from the lower Carboniferous through lower Permian. Outsized clasts, thin pebble-rich diamictites and slumps represent the last of the late Paleozoic glacially influenced deep-water marine sediments in the Mojón de Hierro Fm. and the Paleozoic of Patagonia. U-Pb analysis of detrital zircons separated from slope sediments reveal groupings (20 myr bins, n≥5 zircons) with peak depositional ages of 420, 540 to 660 and 1040 Ma. Zircon age populations recovered from the Mojón de Hierro Fm. compare well with bedrock ages of the Deseado Massif of SE Patagonia, suggesting this may be a potential source of sediments. The maximum depositional age of the sediments is 306.05 ± 3.7 Ma (2σ) as determined by the median age of the two youngest concordant zircons that overlap in error. The youngest zircon from the analysis yields a 238U/206Pb age of 301.3 ± 4.5 Ma (2σ; MSWD = 2.3). Younger zircons from the analysis compare well with the age of granite bedrock exposed along the basin margin to the E-NE suggesting they may reflect a more proximal source. These data, which indicate a maximum age of late Carboniferous for the Mojón de Hierro Fm, provide the first geochemical constraints for the timing of final deposition of glaciomarine sediments in the Tepuel-Genoa Basin, and contributes to the biostratigraphic correlation of the late Paleozoic succession in Patagonia with other key LPIA basins that has thus far been hindered by faunal provincialism.

  6. Sediment deposition from Hurricane Rita on Hackberry Beach chenier in southwestern Louisiana: Chapter 6E in Science and the storms-the USGS response to the hurricanes of 2005

    Science.gov (United States)

    Faulkner, Stephen; Barrow, Wylie; Doyle, Thomas; Baldwin, Michael; Michot, Thomas; Wells, Christopher; Jeske, Clint

    2007-01-01

    Hurricane Rita significantly impacted the chenier forests of southwestern Louisiana, an important habitat for Neotropical migratory birds. Sediment deposition was measured along transects at Hackberry Beach chenier, and Rita's effects on chenier structure and morphology were determined.

  7. Evaluation of Soil Erosion and Sediment Yield from Ridge Watersheds Leading to Guánica Bay, Puerto Rico, Using SWAT Model

    Science.gov (United States)

    Increased sediment loading to reservoirs and, ultimately, to Guánica Bay and reef areas is a significant concern in Puerto Rico. Sediment deposition has significantly reduced storage capacity of reservoirs, and sediment-attached contaminants can stress corals and negative...

  8. Toxic evaluations of sediments in Tokyo Bay, Japan, using Japanese medaka embryos.

    Science.gov (United States)

    Uno, Seiichi; Kokushi, Emiko; Kawano, Machi; McElroy, Anne E; Koyama, Jiro

    2017-12-01

    Toxic risks of sediments collected from seven sites in Tokyo Bay were evaluated using Japanese medaka embryos. Those sediments with slight pore water were placed in grass petri dishes without overlying water. The most remarkable effect in the field sediment was to cause hatching delay in embryos, and the longest time until hatching took was 12.5 ± 1.6 days post-fertilization (dpf), although that in control group was 10.1 ± 0.7 dpf. A significant delay in hatching was observed at four sites. Because total carbon concentrations were relatively high in sediments at three of these four sites, several chemicals were expected to be residues in these sites and could cause their delay. Although extreme mortality was not observed at all sites, sediments collected from the site close to Kawasaki city induced 10 % mortality. Polycyclic aromatic hydrocarbon (PAH) concentrations were remarkably high at this site compared with other sites, and thus PAH toxicities could be causing the mortality. Concentration of heavy metals such as cadmium, copper, lead, and zinc in sediments were also determined, but no clear relationship was found between toxicities to embryos and the distribution of their concentrations.

  9. Evaluation of Baermann apparatus sedimentation time on recovery of Strongylus vulgaris and S. edentatus third stage larvae from equine coprocultures.

    Science.gov (United States)

    Bellaw, Jennifer L; Nielsen, Martin K

    2015-06-30

    Traditional methods of diagnosing equine Strongylinae infections require culturing feces, sedimenting the culture media in Baermann apparatuses, collecting the sediment, and morphologically identifying recovered third stage larvae. However, this method is plagued by low negative predictive values. This study evaluated sedimentation time within the Baermann apparatus by comparing larval recovery from the traditionally collected sediment, "sediment 1", and from the usually discarded remaining fluid contents, "sediment 2", of the Baermann apparatus after 12, 24, and 48 h. A grand total of 147,482 larvae were recovered and examined. Sedimentation time did not significantly influence total larval recovery. At all three durations, significantly more Cyathostominae and Strongylus vulgaris larvae were covered from sediment 1 than from sediment 2. However, less than 60% of all recovered Strongylus edentatus were recovered from sediment 1. As 95% of S. vulgaris larvae were always recovered from sediment 1, the need for collection and examination of the remaining fluid contents of the Baermann apparatus is obviated when performing coprocultures for diagnosis of S. vulgaris infections, and sedimentation for 12h is adequate. Approximately 70% of Cyathostominae were recovered in sediment 1 at all durations, suggesting that 12h of sedimentation is adequate, although there is a need for future research to evaluate the risk of selection bias at differing sedimentation times among individual cyathostomin species. In contrast to S. vulgaris, collecting and examining the entire contents of the Baermann apparatus may be necessary when an increased diagnostic sensitivity and negative predictive value is desired in diagnosing S. edentatus infections as only 38-61% of larvae were recovered from sediment 1 portion of the Baermann apparatus. This information will allow researchers and practitioners to make more informed decisions in choosing appropriate larval recovery techniques, balancing

  10. A tale of two storms: Surges and sediment deposition from Hurricanes Andrew and Wilma in Florida’s southwest coast mangrove forests: Chapter 6G in Science and the storms-the USGS response to the hurricanes of 2005

    Science.gov (United States)

    Smith, Thomas J.; Anderson, Gordon H.; Tiling, Ginger

    2007-01-01

    Hurricanes can be very different from each other. Here we examine the impacts that two hurricanes, Andrew and Wilma, had in terms of storm surge and sediment deposition on the southwest coast of Florida. Although Wilma was the weaker storm, it had the greater impact. Wilma had the higher storm surge over a larger area and deposited more sediment than did Andrew. This effect was most likely due to the size of Wilma's eye, which was four times larger than that of Andrew.

  11. Sediment Sources, Depositional Environment, and Diagenetic Alteration of the Marcellus Shale, Appalachian Basin, USA: Nd, Sr, Li and U Isotopic Constraints

    Science.gov (United States)

    Phan, T. T.; Capo, R. C.; Gardiner, J. B.; Stewart, B. W.

    2017-12-01

    The organic-rich Middle Devonian Marcellus Shale in the Appalachian Basin, eastern USA, is a major target of natural gas exploration. Constraints on local and regional sediment sources, depositional environments, and post-depositional processes are essential for understanding the evolution of the basin. In this study, multiple proxies, including trace metals, rare earth elements (REE), the Sm-Nd and Rb-Sr isotope systems, and U and Li isotopes were applied to bulk rocks and authigenic fractions of the Marcellus Shale and adjacent limestone/sandstone units from two locations separated by 400 km. The range of ɛNd values (-7.8 to -6.4 at 390 Ma) is consistent with a clastic sedimentary component derived from a well-mixed source of fluvial and eolian material of the Grenville orogenic belt. The Sm-Nd isotope system and bulk REE distributions appear to have been minimally affected by post-depositional processes, while the Rb-Sr isotope system shows evidence of limited post-depositional redistribution. While REE are primarily associated with silicate minerals (80-95%), REE patterns of sequentially extracted fractions reflect post-depositional alteration at the intergranular scale. Although the chemical index of alteration (CIA = 54 to 60) suggests the sediment source was not heavily weathered, Li isotope data are consistent with progressively increasing weathering of the source region during Marcellus Shale deposition. δ238U values in bulk shale and reduced phases (oxidizable fraction) are higher than those of modern seawater and upper crust. The isotopically heavy U accumulated in these authigenic phases can be explained by the precipitation of insoluble U in anoxic/euxinic bottom water. Unlike carbonate cement within the shale, the similarity between δ238U values and REE patterns of the limestone units and those of modern seawater indicates that the limestone formed under open ocean (oxic) conditions.

  12. Evaluating sediment transport in flood-driven ephemeral tributaries using direct and acoustic methods.

    Science.gov (United States)

    Stark, K.

    2017-12-01

    One common source of uncertainty in sediment transport modeling of large semi-arid rivers is sediment influx delivered by ephemeral, flood-driven tributaries. Large variations in sediment delivery are associated with these regimes due to the highly variable nature of flows within them. While there are many sediment transport equations, they are typically developed for perennial streams and can be inaccurate for ephemeral channels. Discrete, manual sampling is labor intensive and requires personnel to be on site during flooding. In addition, flooding within these tributaries typically last on the order of hours, making it difficult to be present during an event. To better understand these regimes, automated systems are needed to continuously sample bedload and suspended load. In preparation for the pending installation of an automated site on the Arroyo de los Piños in New Mexico, manual sediment and flow samples have been collected over the summer monsoon season of 2017, in spite of the logistical challenges. These data include suspended and bedload sediment samples at the basin outlet, and stage and precipitation data from throughout the basin. Data indicate a complex system; flow is generated primarily in areas of exposed bedrock in the center and higher elevations of the watershed. Bedload samples show a large coarse-grained fraction, with 50% >2 mm and 25% >6 mm, which is compatible with acoustic measuring techniques. These data will be used to inform future site operations, which will combine direct sediment measurement from Reid-type slot samplers and non-invasive acoustic measuring methods. Bedload will be indirectly monitored using pipe-style microphones, plate-style geophones, channel hydrophones, and seismometers. These instruments record vibrations and acoustic signals from bedload impacts and movement. Indirect methods for measuring of bedload have never been extensively evaluated in ephemeral channels in the southwest United States. Once calibrated

  13. Evaluation of the toxicity of sediments from the Anniston PCB Site to the mussel Lampsilis siliquoidea

    Science.gov (United States)

    Schein, Allison; Sinclair, Jesse A.; MacDonald, Donald D.; Ingersoll, Christopher G.; Kemble, Nile E.; Kunz, James L.

    2015-01-01

    The Anniston Polychlorinated Biphenyl (PCB) Site is located in the vicinity of the municipality of Anniston in Calhoun County, in the north-eastern portion of Alabama. Although there are a variety of land-use activities within the Choccolocco Creek watershed, environmental concerns in the area have focused mainly on releases of PCBs to aquatic and riparian habitats. PCBs were manufactured by Monsanto, Inc. at the Anniston facility from 1935 to 1971. The chemicals of potential concern (COPCs) in sediments at the Anniston PCB Site include: PCBs, mercury, metals, polycyclic aromatic hydrocarbons (PAHs), organochlorine and organophosphorous pesticides, volatile organic compounds (VOCs), semivolatile organic compounds (SVOCs), and polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs). The purpose of this study was to evaluate the toxicity of PCB-contaminated sediments to the juvenile fatmucket mussel (Lampsilis siliquoidea) and to characterize relationships between sediment chemistry and the toxicity of sediment samples collected from the Anniston PCB Site using laboratory sediment testing. Samples were collected in August 2010 from OU-4 of the Anniston PCB Site, as well as from selected reference locations. A total of 32 samples were initially collected from six test sites and one reference site within the watershed. A total of 23 of these 32 samples were evaluated in 28-day whole-sediment toxicity tests conducted with juvenile mussels (L. siliquoidea). Physical and chemical characterization of whole sediment included grain size, total organic carbon (TOC), nutrients, PCBs, parent and alkylated PAHs, organochlorine pesticides, PCDD/PCDFs, total metals, simultaneously extracted metals (SEM), and acid volatile sulfide (AVS). Sediment collected from Snow Creek and Choccolocco Creek contained a variety of COPCs. Organic contaminants detected in sediment included PCBs, organochlorine pesticides, PCDDs/PCDFs, and PAHs. In general, the highest

  14. Chemistry of marine sediments

    International Nuclear Information System (INIS)

    Yen, T.F.

    1977-01-01

    Some topics considered are as follows: characterization of sediments in the vicinity of offshore petroleum production; thermal alteration experiments on organic matter in recent marine sediments as a model for petroleum genesis; composition of polluted bottom sediments in Great Lakes harbors; distribution of heavy metals in sediment fractions; recent deposition of lead off the coast of southern California; release of trace constituents from sediments resuspended during dredging operations; and migration of chemical constituents in sediment-seawater interfaces

  15. Kinetics of Uranium(VI) Desorption from Contaminated Sediments: Effect of Geochemical Conditions and Model Evaluation

    International Nuclear Information System (INIS)

    Liu, Chongxuan; Shi, Zhenqing; Zachara, John M.

    2009-01-01

    Stirred-flow cell experiments were performed to investigate the kinetics of uranyl (U(VI)) desorption from a contaminated sediment collected from the Hanford 300 Area at the US Department of Energy (DOE) Hanford Site, Washington. Three influent solutions of variable pH, Ca and carbonate concentrations that affected U(VI) aqueous and surface speciation were used under dynamic flow conditions to evaluate the effect of geochemical conditions on the rate of U(VI) desorption. The measured rate of U(VI) desorption varied with solution chemical composition that evolved as a result of thermodynamic and kinetic interactions between the influent solutions and sediment. The solution chemical composition that led to a lower equilibrium U(VI) sorption to the solid phase yielded a faster desorption rate. The experimental results were used to evaluate a multi-rate, surface complexation model (SCM) that has been proposed to describe U(VI) desorption kinetics in the Hanford sediment that contained complex sorbed U(VI) species in mass transfer limited domains. The model was modified and supplemented by including multi-rate, ion exchange reactions to describe the geochemical interactions between the solutions and sediment. With the same set of model parameters, the modified model reasonably well described the evolution of major ions and the rates of U(VI) desorption under variable geochemical and flow conditions, implying that the multi-rate SCM is an effective way to describe U(VI) desorption kinetics in subsurface sediments

  16. Evaluation of the Siltation of River Taquari, Pantanal, Brazil, through 210Pb Geochronology of Floodplain Lake Sediments

    Directory of Open Access Journals (Sweden)

    Godoy José M.

    2002-01-01

    Full Text Available This work presents the 210Pb geochronology of seven bottom sediment cores, collected in three floodplain lakes located in the area of the middle Taquari River, Pantanal, Brazil. In five of them, a significant increase in the sediment mass deposition rate was observed, reflecting an increase of the sediment input to the Pantanal. Additionally, in order to validate the 210Pb results, the mercury content was determined for two sediment cores, showing that despite a constant concentration, the flux of Hg has increased due to an increase in the mass sedimentation rate. This increase can be attributed to the expansion of agricultural activity in the upper Taquari River during the last 25 years.

  17. The ESR age of Portlandia arctica shells from glacial deposits of Central Latvia . an answer to a controversy on the age and genesis of their enclosing sediments

    Science.gov (United States)

    Molodkov, Anatoly; Dreimanis, Aleksis; ĀBoltiņš, Ojars; Raukas, Anto

    The occurrence of Portlandia arctica shells in glacigenic sediments of Central Latvia had created a controversy in many publications about (1) their age ranging from the Holsteinian to the Late Weichselian and (2) the genesis of their enclosing sediments: glacial, glaciomarine or marine. Our reinvestigation of the main object of controversy, the Lı¯čupe site, leads to a conclusion that the sedimentary package of diamictons, clays and sands containing Portlandia arctica shells and marine microfossils is a large glacial raft that had been transported and deposited by the Riga lobe during the Weichselian. The electron spin resonance (ESR) ages on five sets of Portlandia arctica shells from the Lı¯čupe and Daugmales Tomēni sites range from 86.0±6.8 to 105.0±9.2 ka BP. These ESR age determinations and the cool climate indicators of the associated microflora and microfauna suggest that their source sediments, probably in the Gulf of Riga, are marine clays of Early Weichselian age, probably correlative to the Brørup Interstadial. In Central Latvia Portlandia arctica shells and their enclosing clay occur resedimented or translocated in glacial deposits during Weichselian glacial advances.

  18. Evaluating Competition in the Loan and Deposit Market using the ...

    African Journals Online (AJOL)

    kirstam

    Key words: Competition, loan and deposit market, Boone indicator approach, Zimbabwe ... Performance measurement is a framework for assessing the effect of government ... resource wastage and to lower the market prices of financial products (Berger & ..... costs are more efficient and gain more market share or profits.

  19. A MULTILAYER BIOCHEMICAL DRY DEPOSITION MODEL 2. MODEL EVALUATION

    Science.gov (United States)

    The multilayer biochemical dry deposition model (MLBC) described in the accompanying paper was tested against half-hourly eddy correlation data from six field sites under a wide range of climate conditions with various plant types. Modeled CO2, O3, SO2<...

  20. Electrochemical evaluation of under-deposit corrosion and its inhibition using the wire beam electrode method

    Energy Technology Data Exchange (ETDEWEB)

    Tan Yongjun, E-mail: yj.tan@curtin.edu.a [Western Australian Corrosion Research Group, Department of Chemistry, Curtin University, GPO Box U1987, Perth (Australia); Fwu, Young; Bhardwaj, Kriti [Western Australian Corrosion Research Group, Department of Chemistry, Curtin University, GPO Box U1987, Perth (Australia)

    2011-04-15

    Research highlights: A new experiment method for evaluating under-deposit corrosion and its inhibitors. Under-deposit corrosion did not occur in a CO{sub 2} saturated pure brine solution. Inhibitor imidazoline addition and O{sub 2} contamination initiated under-deposit corrosion. Inhibitor imidazoline reduced general corrosion but enhanced localised corrosion. - Abstract: A new experimental method has been applied to evaluate under-deposit corrosion and its inhibition by means of an electrochemically integrated multi-electrode array, namely the wire beam electrode (WBE). Maps showing galvanic current and corrosion potential distributions were measured from a WBE surface that was partially covered by sand. Under-deposit corrosion did not occur during the exposure of the WBE to carbon dioxide saturated brine under ambient temperature. The introduction of corrosion inhibitor imidazoline and oxygen into the brine was found to significantly affect the patterns and rates of corrosion, leading to the initiation of under-deposit corrosion over the WBE.

  1. Field manual for stream sediment reconnaissance. Savannah River Laboratory National Uranium Resource Evaluation Program

    International Nuclear Information System (INIS)

    Ferguson, R.B.; Price, V.; Baucom, E.I.

    1976-07-01

    A manual is presented that is intended to direct and coordinate field operations, site selection, stream sediment sample collection, water sample collection, and information codes for the Savannah River Laboratory (SRL) contribution to the National Uranium Resource Evaluation (NURE) program. The manual provides public relations information for field sampling teams as well as technical direction

  2. Unravelling mixed sediment signals in the floodplains of the Rhine catchment using end member modelling of grain size distributions

    NARCIS (Netherlands)

    Erkens, G.; Toonen, W.H.J.; Cohen, K.M.; Prins, M.A.

    2013-01-01

    During sediment transport downstream, river systems mix sediments from different parts of their catchments. During deposition, sediments are often unmixed again in different depositional environments (facies). During fluvial transport, between erosion and deposition of sediment, the sediment is

  3. Regional setting, distribution and genesis of surficial uranium deposits in calcretes and associated sediments in Western Australia

    International Nuclear Information System (INIS)

    Butt, C.R.M.; Mann, A.W.; Horwitz, R.C.

    1984-01-01

    Surficial uranium deposits in Western Australia are largely in the Yilgarn Block in areas of Archean granitoids and greenstones, and in the Gascoyne Province in Proterozoic granites and gneisses. The region has had a long weathering history marked by continuous planation developing a regolith up to 100 metres thick. The distribution of calcrete type uranium deposits is controlled by geologic as well as weathering, erosion and climatic factors. Valley, playa and terrace deposits are recognized. The principal known surficial uranium deposit, Yeelirrie, occurs in the Yilgarn block as a valley deposit. (author)

  4. Sediment Resuspension and Deposition on Seagrass Leaves Impedes Internal Plant Aeration and Promotes Phytotoxic H2S Intrusion.

    Science.gov (United States)

    Brodersen, Kasper E; Hammer, Kathrine J; Schrameyer, Verena; Floytrup, Anja; Rasheed, Michael A; Ralph, Peter J; Kühl, Michael; Pedersen, Ole

    2017-01-01

    HIGHLIGHTS: Sedimentation of fine sediment particles onto seagrass leaves severely hampers the plants' performance in both light and darkness, due to inadequate internal plant aeration and intrusion of phytotoxic H 2 S. Anthropogenic activities leading to sediment re-suspension can have adverse effects on adjacent seagrass meadows, owing to reduced light availability and the settling of suspended particles onto seagrass leaves potentially impeding gas exchange with the surrounding water. We used microsensors to determine O 2 fluxes and diffusive boundary layer (DBL) thickness on leaves of the seagrass Zostera muelleri with and without fine sediment particles, and combined these laboratory measurements with in situ microsensor measurements of tissue O 2 and H 2 S concentrations. Net photosynthesis rates in leaves with fine sediment particles were down to ~20% of controls without particles, and the compensation photon irradiance increased from a span of 20-53 to 109-145 μmol photons m -2 s -1 . An ~2.5-fold thicker DBL around leaves with fine sediment particles impeded O 2 influx into the leaves during darkness. In situ leaf meristematic O 2 concentrations of plants exposed to fine sediment particles were lower than in control plants and exhibited long time periods of complete meristematic anoxia during night-time. Insufficient internal aeration resulted in H 2 S intrusion into the leaf meristematic tissues when exposed to sediment resuspension even at relatively high night-time water-column O 2 concentrations. Fine sediment particles that settle on seagrass leaves thus negatively affect internal tissue aeration and thereby the plants' resilience against H 2 S intrusion.

  5. Sediment Resuspension and Deposition on Seagrass Leaves Impedes Internal Plant Aeration and Promotes Phytotoxic H2S Intrusion

    Directory of Open Access Journals (Sweden)

    Kasper E. Brodersen

    2017-05-01

    Full Text Available HIGHLIGHTS:Sedimentation of fine sediment particles onto seagrass leaves severely hampers the plants' performance in both light and darkness, due to inadequate internal plant aeration and intrusion of phytotoxic H2S.Anthropogenic activities leading to sediment re-suspension can have adverse effects on adjacent seagrass meadows, owing to reduced light availability and the settling of suspended particles onto seagrass leaves potentially impeding gas exchange with the surrounding water. We used microsensors to determine O2 fluxes and diffusive boundary layer (DBL thickness on leaves of the seagrass Zostera muelleri with and without fine sediment particles, and combined these laboratory measurements with in situ microsensor measurements of tissue O2 and H2S concentrations. Net photosynthesis rates in leaves with fine sediment particles were down to ~20% of controls without particles, and the compensation photon irradiance increased from a span of 20–53 to 109–145 μmol photons m−2 s−1. An ~2.5-fold thicker DBL around leaves with fine sediment particles impeded O2 influx into the leaves during darkness. In situ leaf meristematic O2 concentrations of plants exposed to fine sediment particles were lower than in control plants and exhibited long time periods of complete meristematic anoxia during night-time. Insufficient internal aeration resulted in H2S intrusion into the leaf meristematic tissues when exposed to sediment resuspension even at relatively high night-time water-column O2 concentrations. Fine sediment particles that settle on seagrass leaves thus negatively affect internal tissue aeration and thereby the plants' resilience against H2S intrusion.

  6. Evaluation and selection of test methods for assessment of contaminated sediments in the Baltic Sea

    DEFF Research Database (Denmark)

    Lehtonen, Kari; Ahvo, Aino; Berezina, Nadya

    The purpose of the CONTEST project (2014-15) is to test, develop, evaluate and select suitable biological methods to be applied in the quantitative and qualitative assessment of toxicity of anthropogenically contaminated sediments in the Baltic Sea marine region. Here is presented results from...... showed large variability in the sensitivity of the different biotests. Most of the tests applied showed concentration-dependent effects on the test organisms. New experiments will be carried out in 2015. The CONTEST project is funded by the Nordic Council of Ministers and the Finnish Ministry...... a set of pilot experiments, which were performed by the participating laboratories. Chemical analysis of the contaminated harbour sediment chosen as the test matrix confirmed the presence of high concentrations of polycyclic aromatic hydrocarbons, organotins and trace metals, and the sediment...

  7. An evaluation of technologies for the heavy metal remediation of dredged sediments.

    Science.gov (United States)

    Mulligan, C N; Yong, R N; Gibbs, B F

    2001-07-30

    Sediments dewatering is frequently necessary after dredging to remediate and treat contaminants. Methods include draining of the water in lagoons with or without coagulants and flocculants, or using presses or centrifuges. Treatment methods are similar to those used for soil and include pretreatment, physical separation, thermal processes, biological decontamination, stabilization/solidification and washing. However, compared to soil treatment, few remediation techniques have been commercially used for sediments. In this paper, a review of the methods that have been used and an evaluation of developed and developing technologies is made. Sequential extraction technique can be a useful tool for determining metal speciation before and after washing. Solidification/stabilization techniques are successful but significant monitoring is required, since the solidification process can be reversible. In addition, the presence of organics can reduce treatment efficiency. Vitrification is applicable for sediments but expensive. Only if a useful glass product can be sold will this process be economically viable. Thermal processes are only applicable for removal of volatile metals, such as mercury and costs are high. Biological processes are under development and have the potential to be low cost. Since few low cost metal treatment processes for sediments are available, there exists significant demand for further development. Pretreatment may be one of the methods that can reduce costs by reducing the volumes of sediments that need to be treated.

  8. Embryotoxicity and genotoxicity evaluation of sediments from Yangtze River estuary using zebrafish (Danio rerio) embryos.

    Science.gov (United States)

    Li, Qian; Chen, Ling; Liu, Li; Wu, Lingling

    2016-03-01

    Sediments function both as a sink and a source of pollutants in aquatic ecosystems and may impose serious effects on benthic organisms and human health. As one of the largest estuaries in the world, the Yangtze River estuary suffers from abundant wastewater from the coastal cities. In this study, the zebrafish (Danio rerio) embryos were employed in the fish embryo test and a comet assay to evaluate the embryotoxicity and genotoxicity of the sediments from the Yangtze River estuary, respectively. Results showed that the sediments from the Yangtze River estuary significantly increased mortality, induced development abnormalities, and reduced hatching rate and heart rate of zebrafish embryos after 96 h of exposure. Significant genotoxicity was observed in the samples relative to the controls. Relatively low-level embryotoxicity and genotoxicity of sediments were found in the Yangtze River compared with other river systems. Toxic responses were also discussed in relation to the analyzed organic contaminants in sediments. More attention should be paid to non-priority pollutant monitoring in the Yangtze River estuary.

  9. Effect of depositional environment and sources of pollution on uranium concentration in sediment, coral, algae and seagrass species from the Gulf of Aqaba (Red Sea)

    International Nuclear Information System (INIS)

    Abu-Hilal, A.H.

    1994-01-01

    Uranium concentrations were determined in sediment samples, four hard and two soft corals, one seagrass and four species of algae collected from phosphate-polluted sites in the northern reef area of the Gulf of Aqaba. High uranium concentrations were found in all samples examined from a phosphate-polluted site near a phosphate loading berth compared to the unpolluted ones. Uranium levels, U/Ca ratios, concentration and discrimination factors were also high compared to those reported from other regions of the world. The effects of the exported raw phosphate powder as the main source of pollution and depositional environment on the concentration of uranium in the examined species are discussed. (Author)

  10. Geochemical constraints on the provenance and depositional environment of the Messinian sediments, onshore Nile Delta, Egypt: Implications for the late Miocene paleogeography of the Mediterranean

    Science.gov (United States)

    Leila, Mahmoud; Moscariello, Andrea; Šegvić, Branimir

    2018-07-01

    The Messinian sequence rocks in the Nile Delta present prolific hydrocarbon reservoirs and are, therefore, of great importance from the aspect of petroleum exploration and development strategies. Yet, little is known about their tectonic provenance and depositional setting. This study focuses on the geochemical signatures archived in the Messinian siliciclastic sediments to employ them as a powerful tool to elucidate the basin evolution during the Messinian salinity crisis (MSC). The pre-MSC Qawasim sediments are texturally and compositionally immature. They are enriched in lithic fragments, foraminiferal bioclasts, and rounded heavy minerals suggesting a significant contribution from the pre-existing Cretaceous-Eocene mixed carbonate-siliciclastic rocks bordering the Nile Delta. In contrast, the textural and mineralogical compositions as well as a range of geochemical proxies (e.g., chemical index of alteration and weathering CIA, CIW as well as index of chemical variability ICV and Zr/Sc ratio) are in favor of prolonged weathering and at least second-cycle origin of the MSC Abu Madi sediments. The mutually correspondent elemental ratios (e.g., Al2O3/TiO2, K2O/Na2O, Zr/Hf, Rb/Sr, Cr/Zr, and Cr/Th) and uniform weathering trends are indicatives for a similar provenance of the pre-MSC Qawasim and MSC Abu Madi sediments. Rare earth element (REE) distribution reveals a significant enrichment in LREE, depletion in HREE, relatively high (La/Yb)N (mean > 9), low (Gd/Yb)N (mean sediments to have been eroded and recycled from the older pre-MSC Qawasim sediments by gravity-flow processes and fluvial channels prior to redeposition as incised-valley-fills during the late stage of the MSC. The geochemical paleoenvironmental indicators such as C-value, Sr/Cu and Sr/Ba confirm arid-dry climatic conditions during the onset of the MSC consistent with the Mediterranean desiccation. These indicators also depict a transition from freshwater to relatively normal salinity conditions

  11. Mineral deposits of the Silica plateau – evaluation of selected geological factors of the environment

    Directory of Open Access Journals (Sweden)

    BalហBartolomej

    2001-12-01

    Full Text Available The Silica plateau is a part of a greatest karst area in the Slovak republic - Protected Landscape Area Slovak karst (CHKO Slovenský kras. Karst areas belong to the most sensitive environments, from the point of view of impacts caused by anthropogenous activities. This area reacts sensitively, disturbing the environmental balance caused by mining of mineral deposits. Three mineral deposits of industrial rocks: one deposit of decorative stone - Silická Brezová and two deposits of building stone – Silická Brezová I and Lipovník, respectively, were registered on January 1-st, 2001 in the territory of the Silica plateau. Some deposits utilized in the past namely two deposits of building raw materials (Hrušov and Krásnohorská Dlhá Lúka and one Pb-Zn ore deposit (Ardovo are also mentioned and evaluated in the paper. From the point of view of economical potential of the area, mineral deposits have a character of geopotentials. However the utilization of deposits represents negative anthropogenous impact. When compared with another forms of optimal and rational utilization of the country, e.g. agriculture, forestry, water management, construction, tourism etc., mineral deposits have a character of geobarriers. This research was carried out in the frame of the VEGA Grant No. 1/6090/1999.

  12. Coarse-grained sediment delivery and distribution in the Holocene Santa Monica Basin, California: Implications for evaluating source-to-sink flux at millennial time scales

    Science.gov (United States)

    Romans, B.W.; Normark, W.R.; McGann, M.M.; Covault, J.A.; Graham, S.A.

    2009-01-01

    Utilizing accumulations of coarse-grained terrigenous sediment from deep-marine basins to evaluate the relative contributions of and history of controls on sediment flux through a source-to-sink system has been difficult as a result of limited knowledge of event timing. In this study, six new radiocarbon (14C) dates are integrated with five previously published dates that have been recalibrated from a 12.5-m-thick turbidite section from Ocean Drilling Program (ODP) Site 1015 in Santa Monica Basin, offshore California. This borehole is tied to high-resolution seismic-reflection profiles that cover an 1100 km2 area of the middle and lower Hueneme submarine fan and most of the basin plain. The resulting stratigraphic framework provides the highest temporal resolution for a thick-bedded Holocene turbidite succession to date, permitting an evaluation of source-to-sink controls at millennial (1000 yr) scales. The depositional history from 7 ka to present indicates that the recurrence interval for large turbidity-current events is relatively constant (300-360 yr), but the volume of sediment deposited on the fan and in the basin plain has increased by a factor of 2 over this period. Moreover, the amount of sand per event on the basin plain during the same interval has increased by a factor of 7. Maps of sediment distribution derived from correlation of seismic-reflection profiles indicate that this trend cannot be attributed exclusively to autogenic processes (e.g., progradation of depocenters). The observed variability in sediment accumulation rates is thus largely controlled by allogenic factors, including: (1) increased discharge of Santa Clara River as a result of increased magnitude and frequency of El Ni??o-Southern Oscillation (ENSO) events from ca. 2 ka to present, (2) an apparent change in routing of coarse-grained sediment within the staging area at ca. 3 ka (i.e., from direct river input to indirect, littoral cell input into Hueneme submarine canyon), and (3

  13. Non cardiopatic and cardiopatic beta thalassaemic patients: quantitative and qualitative cardiac iron deposition evaluation with MRI

    International Nuclear Information System (INIS)

    Macarini, Luca; Marini, Stefania; Scardapane, Arnaldo; Pietrapertosa, Anna; Ettore, Giovanni Carlo

    2005-01-01

    Purpose: Cardiomyopathy is one of the major complications of β thalassaemia major as a result of transfusion iron overload. The aim of our study is to evaluate with MR if there is any difference of iron deposition signal intensity (SI) or distribution between non-cardiopatic and cardiopatic thalassaemic patients in order to establish if there is a relationship between cardiopathy and iron deposition. Materials and methods: We studied 20 patients affected by β thalassaemia major, of whom 10 cardiopatic and 10 non-cardiopatic, and 10 healthy volunteers as control group. Serum ferritin and left ventricular ejection fraction were calculated in thalassaemic patients. All patients were examinated using a 1.5 MR unit with ECG-gated GE cine-MR T2*-weighted, SE T1-weighted and GE T2*-weighted sequences. In all cases, using an adequate ROI, the myocardial and skeletal muscle signal intensity (SI), the myocardial/skeletal muscle signal intensity radio (SIR) and the SI average of the myocardium and skeletal muscle were calculated for every study group. The qualitative evaluation of iron deposition distribution was independently performed by three radiologists who analysed the extension, the site and the morphology of iron deposition on the MR images and reported their observations on the basis of a four-level rating scale: 0 (absent), 1 (limited), 2 (partial), 3 (widespread deposition). The results of quantitative and qualitative evaluation were analysed with statistical tests. Results: Cardiac iron deposition was found in 8/10 non-cardiopatic thalassaemic patients and in all cardiopatic thalassaemic patients. We noticed a significant SI difference (p>0.05) between the healthy volunteer control group and the thalassaemic patients with iron deposition, but no significant SI difference in iron deposition between non-cardiopatic thalassaemic patients in the areas evaluated. The qualitative evaluation revealed a different distribution of iron deposition between the two

  14. Evaluation of surficial sediment toxicity and sediment physico-chemical characteristics of representative sites in the Lagoon of Venice (Italy)

    Science.gov (United States)

    Losso, C.; Arizzi Novelli, A.; Picone, M.; Marchetto, D.; Pessa, G.; Molinaroli, E.; Ghetti, P. F.; Volpi Ghirardini, A.

    2004-11-01

    Toxic hazard in sites with varying types and levels of contamination in the Lagoon of Venice was estimated by means of toxicity bioassays based on the early life-stages of the autochthonous sea urchin Paracentrotus lividus. Elutriate was chosen as the test matrix, due to its ability to highlight potential toxic effects towards sensitive biological components of the water column caused by sediment resuspension phenomena affecting the Lagoon. Surficial sediments (core-top 5 cm deep), directly influenced by resuspension/redeposition processes, and core sediments (core 20 cm deep), recording time-mediated contamination, were sampled in some sites located in the lagoonal area most greatly influenced by anthropogenic activities. Particle size, organic matter and water content were also analysed. In two sites, the results of physical parameters showed that the core-top sediments were coarser than the 20-cm core sediments. Sperm cell toxicity test results showed the negligible acute toxicity of elutriates from all investigated sites. The embryo toxicity test demonstrated a short-term chronic toxicity gradient for elutriates from the 20-cm core sediments, in general agreement both with the expected contamination gradient and with results of the Microtox® solid-phase test. Elutriates of the core-top 5-cm sediments revealed a totally inverted gradient, in comparison with that for the 20-cm core sediments, and the presence of a "hot spot" of contamination in the site chosen as a possible reference. Investigations on ammonia and sulphides as possible confounding factors excluded their contribution to this "hot spot". Integrated physico-chemical and toxicity results on sediments at various depths demonstrated the presence of disturbed sediments in the central basin of the Lagoon of Venice.

  15. National Uranium Resource Evaluation Program. Hydrogeochemical and stream sediment reconnaissance basic data for Beeville NTMS Quadrangle, Texas. Uranium resource evaluation project

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-31

    Results of a reconnaissance geochemical survey of the Beeville Quadrangle, Texas are reported. Field and laboratory data are presented for 373 groundwater and 364 stream sediment samples. Statistical and areal distributions of uranium and possible uranium-related variables are displayed. A generalized geologic map of the survey area is provided, and pertinent geologic factors which may be of significance in evaluating the potential for uranium mineralization are briefly discussed. The groundwater data indicate that the northwestern corner of the quadrangle is the most favorable for potential uranium mineralization. Favorability is indicated by high uranium concentrations; high arsenic, molybdenum, and vanadium concentrations; and proximity and similar geologic setting to the mines of the Karnes County mining district. Other areas that appear favorable are an area in Bee and Refugio Counties and the northeastern part of the quadrangle. Both areas have water chemistry similar to the Karnes County area, but the northeastern area does not have high concentrations of pathfinder elements. The stream sediment data indicate that the northeastern corner of the quadrangle is the most favorable for potential mineralization, but agricultural practices and mineralogy of the outcropping Beaumont Formation may indicate a false anomaly. The northwestern corner of the quadrangle is considered favorable because of its proximity to the known uranium deposits, but the data do not seem to support this.

  16. National Uranium Resource Evaluation Program. Hydrogeochemical and stream sediment reconnaissance basic data for Beeville NTMS Quadrangle, Texas. Uranium resource evaluation project

    International Nuclear Information System (INIS)

    1979-01-01

    Results of a reconnaissance geochemical survey of the Beeville Quadrangle, Texas are reported. Field and laboratory data are presented for 373 groundwater and 364 stream sediment samples. Statistical and areal distributions of uranium and possible uranium-related variables are displayed. A generalized geologic map of the survey area is provided, and pertinent geologic factors which may be of significance in evaluating the potential for uranium mineralization are briefly discussed. The groundwater data indicate that the northwestern corner of the quadrangle is the most favorable for potential uranium mineralization. Favorability is indicated by high uranium concentrations; high arsenic, molybdenum, and vanadium concentrations; and proximity and similar geologic setting to the mines of the Karnes County mining district. Other areas that appear favorable are an area in Bee and Refugio Counties and the northeastern part of the quadrangle. Both areas have water chemistry similar to the Karnes County area, but the northeastern area does not have high concentrations of pathfinder elements. The stream sediment data indicate that the northeastern corner of the quadrangle is the most favorable for potential mineralization, but agricultural practices and mineralogy of the outcropping Beaumont Formation may indicate a false anomaly. The northwestern corner of the quadrangle is considered favorable because of its proximity to the known uranium deposits, but the data do not seem to support this

  17. Evaluation of effective energy deposition in test fuel during power burst experiment in NSRR

    International Nuclear Information System (INIS)

    Ohnishi, Nobuaki; Inabe, Teruo

    1982-01-01

    In an inpile experiment to study the fuel behavior under reactivity-initiated accident conditions, it is of great importance to understand the time-dependent characteristics of the energy deposited in the test fuel by burst power. The evaluation of the time-dependent energy deposition requires the knowledge of the fission rates and energy deposition per fission in the test fuel, both as a function of time. In the present work, the authors attempted to evaluate the relative fission rate change in the test fuel subjected to the power burst testing in the NSRR through the measurements and analyses of the fission power changes in the NSRR. Utilizing a micro fission chamber and a conventional larger fission chamber, they successfully measured the reactor fission power change ranging over a dozen of decades in magnitude and a thousand seconds in time. The measured power transient agreed quite well with calculated results. In addition, the time-dependent energy deposition per fission in the test fuel including the energy contribution from the driver core was analytically evaluated. The analyses indicate that the energy of about 175 MeV/fission is promptly deposited in the test fuel and that the additional energy of about 11 MeV is deposited afterwards. Finally the fractions of energy deposited in the test fuel until various times after power burst were determined by coupling the time-dependent relative fissions and energy deposition per fission in the test fuel. The prompt energy deposition ranges from about 50 to 80% of the total energy deposition for the reactivity insertion between 1.5 and 4.7 $, and the remaining is the delayed energy deposition. (author)

  18. Evaluation of metals, metalloids, and ash mixture toxicity using sediment toxicity testing.

    Science.gov (United States)

    Stojak, Amber; Bonnevie, Nancy L; Jones, Daniel S

    2015-01-01

    In December 2008, a release of 4.1 million m(3) of coal ash from the Tennessee Valley Authority Kingston Fossil Plant occurred. Ash washed into the Emory River and migrated downstream into the Clinch and Tennessee Rivers. A Baseline Ecological Risk Assessment evaluated risks to ecological receptors from ash in the river system post-dredging. This article describes the approach used and results from sediment toxicity tests, discussing any causal relationships between ash, metals, and toxicity. Literature is limited in the realm of aquatic coal combustion residue (CCR) exposures and the potential magnitude of effects on benthic invertebrates. Sediment samples along a spectrum of ash content were used in a tiered toxicity testing approach and included a combination of 10 day sediment toxicity acute tests and longer-term, partial life cycle "definitive" tests with 2 species (Hyalella azteca and Chironomus dilutus). Arsenic, and to a lesser extent Se, in the ash was the most likely toxicant causing observed effects in the laboratory toxicity tests. Sites in the Emory River with the greatest statistical and biologically significant effects had As concentrations in sediments twice the probable effects concentration of 33 mg/kg. These sites contained greater than 50% ash. Sites with less than approximately 50% ash in sediments exhibited fewer significant toxic responses relative to the reference sediment in the laboratory. The results discussed here present useful evidence of only limited effects occurring from a worst-case exposure pathway. These results provided a valuable line of evidence for the overall assessment of risks to benthic invertebrates and to other ecological receptors, and were crucial to risk management and development of project remediation goals. © 2014 SETAC.

  19. Risk Evaluation of Multiple Hazards during Sediment and Water Related Disasters in a Small Basin

    Science.gov (United States)

    Yamanoi, Kazuki; Fujita, Masaharu

    2016-04-01

    To reduce human damage due to sediment and water related disasters induced by heavy rainfall, warning and evacuation system is very important. In Japan, the Meteorological Agency issues the sediment disaster alert when the potential of sediment disaster increases. Following the alert, local government issues evacuation advisory considering the alert and premonitory phenomena. However, it is very difficult for local people to perceive the dangerousness around them because the alert and advisory do not contain any definite information. Therefore, they sometimes misjudge the evacuation action. One reason of this is not only crucial hazards but also relatively small-scale multiple hazards take place and rise evacuation difficulties during sediment and water related disaster. Examples of small-scale hazards include: rainfall-associated hazards such as poor visibility or road submergence; landslide-associated hazards such as slope failure or sediment inflow; and flood-associated hazards such as overtopping of river dike, inundation, or destruction of bridges. The purpose of this study was to estimate the risk of multiple hazards during disaster events by numerical simulation. We applied the integrated sediment runoff model on unit channels, unit slopes, and slope units to an actual sediment and water related disaster occurred in a small basin in Tamba city, Hyogo, Japan. The maximum rainfall per hour was 91 mm (17/09/2014 2:00˜3:00) and the maximum daily precipitation was 414mm. The integrated model contains semi-physical based landslide prediction (sediment production) model, rainfall runoff model employing the kinematic wave method, model of sediment supply to channels, and bedload and suspended sediment transport model. We evaluated the risk of rainfall-associated hazards in each slope unit into 4 levels (Level I ˜ IV) using the rainfall intensity Ir [mm/hour]. The risk of flood- associated hazards were also estimated using the ratio of calculated water level and

  20. History of atmospheric deposition of Cd, Hg, and Pb in North America: Evidence from lake and peat bog sediments

    International Nuclear Information System (INIS)

    Norton, S.A.; Dillon, P.J.; Evans, R.D.; Mierle, G.; Kahl, J.S.

    1990-01-01

    The precipitation chemistry and lake and peat sediment chemistry of three metals emitted to the atmosphere in significant amounts as a result of anthropogenic activity are reviewed. The three metals, Cd, Hg, and Pb, have contrasting source terms, atmospheric residence times, and chemical mobility. Lake and ombrotrophic peat bog sediments record increases in the concentrations and accumulation rates of the metals for most of temperate North America for the last 100 years. These increases are largely related to the burning of coal, smelting of nonferrous metals, the transportation industry, and the industrial production of chlorine. Modern atmospheric fluxes of Cd in central North America are about 1,000 times background fluxes; accumulation rates for Cd in sediments have increased two to 3 times above background, beginning about 100 years ago. Global scale Hg pollution off the atmosphere is suggested by concentrations in northern hemisphere air that are double the Hg content of southern hemisphere air. Accumulation rates of Hg in sediment have approximately doubled in the last 100 years. However, these rates are approximately an order of magnitude less than those for Cd. Modern increases in Pb concentrations are ubiquitous for all lakes examines thus far in North America. Input is from multiple sources and thus the timing of increased accumulation rates in sediment varies across the continent. Typical modern accumulation rates reach maxima at 20 to 30 mg/sq-m/yr, or 100 times that of Cd and 1,000 times that off Hg. Recent decreases in atmospheric lead are reflected in decreases in the accumulation rate of Pb in both lake and peat bog sediment in eastern North America

  1. Evaluation of the growth of carbonaceous deposit in steady state Tore Supra using infrared thermography

    International Nuclear Information System (INIS)

    Mitteau, R.; Guilhem, D.; Reichle, R.; Vallet, J.C.; Roche, H.; Buravand, Y.; Chantant, M.; Tsitrone, E.; Brosset, C.; Grosman, A.; Chappuis, P.

    2006-01-01

    Fusion devices with carbon as the main armour material are experiencing a growth in carbonaceous deposits at the surface of the plasma facing components. Tore Supra presents such deposits, and has specific features which influence their growth: long pulse operation and cooled walls. Deposits have a low thermal transfer to the cooled structure so that they appear as hot areas with the infrared imaging system looking at the elements surface temperature during plasma discharges. A 'degree of (carbon) deposit' on the toroidal pumped limiter is estimated by establishing the ratio between the apparent power on the limiter derived from the infrared measure and the actual one, deduced from a power balance analysis between the injected and the radiated power. This criterion is used to monitor the evolution of the deposit average thermal resistance. Successive shots have a similar 'degree of deposit', showing that the evaluation makes sense. Two years of data have been compiled (2003 and 2004), representing 3000 discharges (13 h of plasma, including 30 discharges longer than one minute). A three-fold increase in the 'degree of deposit' over six months is evidenced, following a limiter clean-up early in 2003. A comparison with calorimetric data produces a similar result, albeit less pronounced. Large steps in the degree of deposit are sometimes observed, usually correlated with identified events such as disruption, vessel opening, conditioning or plasma parameters change. It indicates that the deposit thermal resistance can change rapidly, although a systematic correlation with the above mentioned events could not be established

  2. Evaluation of physical and chemical properties and their interactions in fat, oil, and grease (FOG) deposits.

    Science.gov (United States)

    Gross, Martin A; Jensen, Jeanette L; Gracz, Hanna S; Dancer, Jens; Keener, Kevin M

    2017-10-15

    Fat, oil and grease (FOG) blockages in sewer systems are a substantial problem in the United States. It has been estimated that over 50% of sewer overflows are a result of FOG blockages. In this work, a thorough laboratory study was undertaken to examine key variables that contribute to FOG deposit formation under controlled conditions. Physical and chemical properties and their interactions were evaluated and conditions that generated deposits that mimicked field FOG deposits were identified. It was found that 96 of the of 128 reaction conditions tested in the laboratory formed FOG deposits with similar physical and chemical characteristics as field FOG deposits. It was also found that FOG deposits can be created through fatty acid crystallization and not just saponification. Furthermore FOG deposits were found to be more complex than previously documented and contain free fatty acids, fatty acid metal salts, triacylglycerol's, diacylglycerol's and, monoacylglycerol's. Lastly it was found that FOG deposits that only contained saturated fatty acids were on average 2.1 times higher yield strength than deposits that contained unsaturated fatty acids. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Evaluation of the growth of carbonaceous deposit in steady state Tore Supra using infrared thermography

    Science.gov (United States)

    Mitteau, R.; Guilhem, D.; Reichle, R.; Vallet, J. C.; Roche, H.; Buravand, Y.; Chantant, M.; Tsitrone, E.; Brosset, C.; Grosman, A.; Chappuis, P.

    2006-03-01

    Fusion devices with carbon as the main armour material are experiencing a growth in carbonaceous deposits at the surface of the plasma facing components. Tore Supra presents such deposits, and has specific features which influence their growth: long pulse operation and cooled walls. Deposits have a low thermal transfer to the cooled structure so that they appear as hot areas with the infrared imaging system looking at the elements surface temperature during plasma discharges. A 'degree of (carbon) deposit' on the toroidal pumped limiter is estimated by establishing the ratio between the apparent power on the limiter derived from the infrared measure and the actual one, deduced from a power balance analysis between the injected and the radiated power. This criterion is used to monitor the evolution of the deposit average thermal resistance. Successive shots have a similar 'degree of deposit', showing that the evaluation makes sense. Two years of data have been compiled (2003 and 2004), representing 3000 discharges (13 h of plasma, including 30 discharges longer than one minute). A three-fold increase in the 'degree of deposit' over six months is evidenced, following a limiter clean-up early in 2003. A comparison with calorimetric data produces a similar result, albeit less pronounced. Large steps in the degree of deposit are sometimes observed, usually correlated with identified events such as disruption, vessel opening, conditioning or plasma parameters change. It indicates that the deposit thermal resistance can change rapidly, although a systematic correlation with the above mentioned events could not be established.

  4. Piracicaba River Basin: evaluation of chemical elements in deep sediment profile by INAA

    Energy Technology Data Exchange (ETDEWEB)

    França, Elvis J. de; Santos, Robson A.; Santos, Katarine M. Barbosa; Silva, Gleyce K. A. [Centro Regional de Ciencias Nucleares do Nordeste (DIAMB/CRCN-NE/CNEN-PE), Recife, PE (Brazil). Div, de Monitoração Ambiental; Fernandes, Elisabete A. de Nadai; Rodrigues, Vanessa S.; Cavalca, Isabel P.O., E-mail: ejfranca@cnen.gov.br, E-mail: lis@cena.usp.br [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil)

    2017-07-01

    Many hydrographic basins have been impacted by anthropogenic sources, the Piracicaba River Basin of the State of São Paulo, is one of that. The total concentrations of chemical elements in deep sediments of basin may be indicate those available in ecosystem. Therefore, in this research concentration of chemical elements on deep sediment profile sampled of Piracicaba River Basin was determined by k0-Instrumental Neutron Activation Analysis. After collecting the 60 cm depth profile, samples were obtained by sectioning the sediment profile in 5 cm layers, totalizing 12 samples. Analytical portions were transferred to polyethylene vials for neutron irradiation at the Nuclear Research Reactor IEA-R1 from the Instituto de Pesquisas Energéticas e Nucleares IPEN/CNEN. After waiting for radiation safe levels, irradiated samples were transported to the Radioisotopes Laboratory from the Centro de Energia Nuclear na Agricultura CENA/USP. High Resolution Gamma-Ray Spectrometry using HPGe detectors was applied to measure the induced radioactivity. The chemical element mass fractions and their respective expanded analytical uncertainties (95% confidence level) were determined by k0-INAA using the in-house software Quantu. Geological reference materials were analyzed with samples to evaluate the quality of the analytical procedure. Results indicated the presence of enriched surface sediments (0-10 cm depth) for As, Ba, Ca, Co, Cs, Fe, Sb, Sc, Sr, Yb and Zn, despite no alteration was observed for Eu, Ta and Tb. Therefore, the evaluation of deep sediment profile afford the chemical element dynamics for the Piracicaba Basin. (author)

  5. Piracicaba River Basin: evaluation of chemical elements in deep sediment profile by INAA

    International Nuclear Information System (INIS)

    França, Elvis J. de; Santos, Robson A.; Santos, Katarine M. Barbosa; Silva, Gleyce K. A.

    2017-01-01

    Many hydrographic basins have been impacted by anthropogenic sources, the Piracicaba River Basin of the State of São Paulo, is one of that. The total concentrations of chemical elements in deep sediments of basin may be indicate those available in ecosystem. Therefore, in this research concentration of chemical elements on deep sediment profile sampled of Piracicaba River Basin was determined by k0-Instrumental Neutron Activation Analysis. After collecting the 60 cm depth profile, samples were obtained by sectioning the sediment profile in 5 cm layers, totalizing 12 samples. Analytical portions were transferred to polyethylene vials for neutron irradiation at the Nuclear Research Reactor IEA-R1 from the Instituto de Pesquisas Energéticas e Nucleares IPEN/CNEN. After waiting for radiation safe levels, irradiated samples were transported to the Radioisotopes Laboratory from the Centro de Energia Nuclear na Agricultura CENA/USP. High Resolution Gamma-Ray Spectrometry using HPGe detectors was applied to measure the induced radioactivity. The chemical element mass fractions and their respective expanded analytical uncertainties (95% confidence level) were determined by k0-INAA using the in-house software Quantu. Geological reference materials were analyzed with samples to evaluate the quality of the analytical procedure. Results indicated the presence of enriched surface sediments (0-10 cm depth) for As, Ba, Ca, Co, Cs, Fe, Sb, Sc, Sr, Yb and Zn, despite no alteration was observed for Eu, Ta and Tb. Therefore, the evaluation of deep sediment profile afford the chemical element dynamics for the Piracicaba Basin. (author)

  6. Evaluation of methods for characterizations of deposits; Utvaerdering av metoder foer avlagringsmaetningar

    Energy Technology Data Exchange (ETDEWEB)

    Hoegberg, J.; Bjoerkman, P. [Vattenfall Utveckling AB, Aelvkarleby (Sweden)

    2001-11-01

    In boilers there are problems with deposits on parts exposed to the flue gas, in particular on heat exchanging parts and to an increasing extent with the changeover to the use of biofuels and wood waste fuels. In order to solve the problems deposits are examined by using a deposit probe and taking deposit samples from the interior of the boiler. In this report an evaluation of methods of analysis is performed based on experiences in both literature and laboratory work. The evaluation forms the basis of an instruction for deposit measurements in 'Vaermeforsks Maethandbok'. The procedure for use of deposit probes is treated as well as the importance of careful and well planned sample preparation before analysis. In the literature a large number of methods used for analysis of deposits from flue ashes and similar applications are found. The methods include chemical analyses of solids and liquids, analysis of crystal structures, thermal properties and the solid mechanics of the materials. Several methods, for example SEM-EDX, XRF, ICP, IC and methods for determining the mechanical and thermal properties are suited for a survey examination of a deposit, while more specialised methods with higher resolution can add information but require a clear framing of a question and in practice are suited for only separate samples. Examples from the latter category are AES, ESCA and TOF-SIMS.

  7. Partitioning and speciation of trace metal diagenesis in differing depositional environments in the sediments of the Oman margin

    Digital Repository Service at National Institute of Oceanography (India)

    Alagarsamy, R.; Wolff, G.A.; Chester, R.

    , 403 004, India; 2 Oceanography Laboratories, Department of Earth and Ocean Sciences, University of Liverpool, Liverpool L69 3GP, UK. (Received: 5 May 2004; accepted: 28 September 2004) Abstract. Organic-rich sediment samples collected from a transect... were immediately frozen ()20C176C) on board prior to transport to the laboratory where they were freeze-dried and stored at )20C176C prior to analysis. 2.2. METHODOLOGY Particulate Mn and Fe in sediments are distributed between a numbers of host...

  8. Analysis of soft-sediment deformation structures in Neogene fluvio-lacustrine deposits of Çaybağı Formation, Eastern Turkey

    Science.gov (United States)

    Koç Taşgin, Calibe; Türkmen, İbrahim

    2009-06-01

    During the Neogene, both strike-slip and extensional regimes coexisted in eastern Turkey and, a number of fault-bounded basins associated with the East Anatolian Fault System developed. The Çaybağı Formation (Late Miocene-Early Pliocene) deposited in one of these basins consists of fluvio-lacustrine deposits. Numerous soft-sediment deformation structures are encountered in this formation, particularly in conglomerates, medium- to coarse-grained tuffaceous sandstones and claystones: folded structures (slumps, convolute laminations, and simple recumbent folds), water-escape structures (intruded sands, internal cusps, interpenetrative cusps and sand volcanoes), and load structures (load casts, pseudonodules, flame structures, and pillow structures). These structures are produced by liquefaction and/or fluidization of the unconsolidated sediments during a seismic shock. Consequently, the existence of seismically-induced deformation structures in the Çaybağı Formation and the association with a Neogene intraformational unconformity, growth faults, and reverse faults in the Çaybağı basin attest to the tectonic activity in this area during the Late Miocene and Early Pliocene. The East Anatolian Fault System, in particular the Uluova fault zone, is the most probable seismogenic source. Earthquakes with a magnitude of over 5 in the Richter scale can be postulated.

  9. Evaluating the impacts of logging activities on erosion and suspended sediment transport in the Caspar Creek watersheds

    Science.gov (United States)

    Jack Lewis

    1998-01-01

    Suspended sediment has been sampled at both the North and South Fork weirs of Caspar Creek in northwestern California since 1963, and at 13 tributary locations in the North Fork since 1986. The North Fork gaging station (NFC) was used as a control to evaluate the effects of logging in the South Fork, in the 1970's, on annual sediment loads. In the most...

  10. Deposits of Large-scale Mass Movements in the Sediments of Hallstätter See (Austria) - Recurrent Natural Hazards at a UNESCO World Cultural Heritage Site

    Science.gov (United States)

    Lauterbach, S.; Strasser, M.; Tjallingii, R.; Kowarik, K.; Reschreiter, H.; Spatl, C.; Brauer, A.

    2017-12-01

    The cultural importance of underground salt mining in Hallstatt (Austria), which is documented since the Middle Bronze Age, has been recognized already 20 years ago by assigning the status of a UNESCO World Cultural Heritage Site to the Hallstatt area, particularly because of the wealth of archaeological artefacts from the Early Iron Age. Local mining activity is well documented for prehistoric times and known to have been repeatedly affected by large-scale mass movements, for example at the end of the Bronze Age and during the Late Iron Age. In contrast, evidence of mining activity between the 5th and late 13th century AD is scarce, which could be related to socio-economic changes but also to continued mass movement activity, possibly biasing the archaeological record. Within the present study, a 15.63-m-long 14C-dated sediment core from Hallstätter See has been investigated with respect to the deposits of large-scale mass movements. Most of the lake sediment sequence consists of cm- to sub-mm-scale laminated carbonate mud with frequently intercalated small-scale turbidites, reflecting seasonally variable detrital input from the tributaries, but two major event layers clearly stand out. The upper one comprises a 2.45-m-thick basal mass transport deposit (containing folded laminated sediments, homogenized sediments with liquefaction structures, and coarse gravel) and an overlying 1.45-m-thick co-genetic turbidite. From the lower event layer only the topmost part of the turbiditic sequence with a (minimum) thickness of 1.49 m was recovered. Based on their sedimentological characteristics, both event layers are interpreted as the subaqueous continuation of large-scale mass movements, which occurred at ca. 1050 and 2300 cal. years BP and possibly originated from the rock walls along the western lake shore where also the salt mining area is located. This indicates that mass movement activity not only threatened prehistoric salt mining, but occurred also repeatedly

  11. Spatial and Temporal Variability of Dust Deposition in the San Juan Mountains, CO: A Network of Late Holocene Lake Sediment Records

    Science.gov (United States)

    Arcusa, S.; Routson, C.; McKay, N.

    2017-12-01

    Millions of stakeholders living in the arid southwestern US rely on snowmelt from the San Juan Mountains of Colorado. However, dust deposition on snow accelerates snowmelt, challenging water management. Dustiness in the southwestern US is primarily mediated by drought, which is projected to increase in frequency and severity. Over the past several millennia, multidecadal-length megadroughts are hypothesized to have enhanced regional dustiness. These past megadroughts were more frequent during the Roman (ca. 1-400 CE) and Medieval (ca. 800-1300 CE) time periods and were similar in duration and severity to those projected for the future. Developing an understanding of the temporal and spatial patterns of past dust deposition in the San Juan Mountains will help inform adaptation strategies for future droughts. A network of short sediment cores from six alpine lakes in the San Juan Mountains were collected in 2016 and 2017 to investigate the spatial patterns of dust deposition. The range in lake basin characteristics in the network, such as catchment size, helps to constrain the influence of secondary dust deposition. Grain size analysis and X-ray Fluorescence were combined with radiocarbon dating to trace the temporal patterns in dust flux over the Late Holocene (the last 2000 years). The End-member Modelling Algorithm (EMMA) was used to estimate the dust proportion in the lake sediment, distinguishing from locally derived catchment material. Comparisons to modern dust-on-snow samples were made to identify the dust size distribution. The results show that deposition trends were not uniform between the south-eastern and north-western San Juans, with increasing trends towards the present in the former, possibly reflecting a shift in dust sources associated with changes in wind speed and direction. Dust levels greater than long term averages were recorded during the Medieval and Roman periods. The network also showed the influence of lake basin parameters, such as the

  12. Lake-sediment record of PAH, mercury, and fly-ash particle deposition near coal-fired power plants in Central Alberta, Canada.

    Science.gov (United States)

    Barst, Benjamin D; Ahad, Jason M E; Rose, Neil L; Jautzy, Josué J; Drevnick, Paul E; Gammon, Paul R; Sanei, Hamed; Savard, Martine M

    2017-12-01

    We report a historical record of atmospheric deposition in dated sediment cores from Hasse Lake, ideally located near both currently and previously operational coal-fired power plants in Central Alberta, Canada. Accumulation rates of spheroidal carbonaceous particles (SCPs), an unambiguous marker of high-temperature fossil-fuel combustion, in the early part of the sediment record (pre-1955) compared well with historical emissions from one of North America's earliest coal-fired power plants (Rossdale) located ∼43 km to the east in the city of Edmonton. Accumulation rates in the latter part of the record (post-1955) suggested inputs from the Wabamun region's plants situated ∼17-25 km to the west. Increasing accumulation rates of SCPs, polycyclic aromatic hydrocarbons (PAHs) and Hg coincided with the previously documented period of peak pollution in the Wabamun region during the late 1960s to early 1970s, although Hg deposition trends were also similar to those found in western North American lakes not directly affected by point sources. A noticeable reduction in contaminant inputs during the 1970s is attributed in part to technological improvements and stricter emission controls. The over one hundred-year historical record of coal-fired power plant emissions documented in Hasse Lake sediments has provided insight into the impact that both environmental regulations and changes in electricity output have had over time. This information is crucial to assessing the current and future role of coal in the world's energy supply. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

  13. Physical and chemical parameters of sediment extraction and fractionation that influence toxicity, as evaluated by microtox (trade name)

    International Nuclear Information System (INIS)

    Ho, K.T.Y.; Quinn, J.G.

    1993-01-01

    Several physical and chemical parameters of sediment extraction and fractionation of organic compounds that influence bioassay results were evaluated. Each parameter was evaluated with a photoluminescent bacterial bioassay (Microtox) as an end point. Three solvents (acetonitrile, acetone, and methanol) were studied for their ability to extract toxic organic components from marine sediments. Acetone extracted the most toxicity, with no difference between acetonitrile and methanol. Two methods of fractionating sediment extracts (silica-gel-column chromatography (SGCC) and acid-base fractionation) were compared. SGCC was more useful because it resulted in a wider range of responses and was faster to perform than acid-base fractionation. Microtox was used to rank four marine sediments with respect to toxicity and to determine if one chemical class (or fraction) was consistently more toxic among different sediments. With some caveats, Microtox results agreed with general chemical concentration trends and other bioassay results in distinguishing between contaminated and noncontaminated sediments. Although results indicated there was not a consistently most toxic fraction among sediments, there was a consistently least toxic fraction. The effect of sediment storage time on toxicity was also evaluated. Results indicated that the most stable chemical fraction (containing nonpolar hydrocarbons) did not change toxicologically for 30 weeks, whereas the more chemically active fraction (containing ketones, quinones, and carboxyls) changed as soon as one week

  14. Early diagenesis in the sediments of the Congo deep-sea fan dominated by massive terrigenous deposits: Part II - Iron-sulfur coupling

    Science.gov (United States)

    Taillefert, Martial; Beckler, Jordon S.; Cathalot, Cécile; Michalopoulos, Panagiotis; Corvaisier, Rudolph; Kiriazis, Nicole; Caprais, Jean-Claude; Pastor, Lucie; Rabouille, Christophe

    2017-08-01

    Deep-sea fans are well known depot centers for organic carbon that should promote sulfate reduction. At the same time, the high rates of deposition of unconsolidated metal oxides from terrigenous origin may also promote metal-reducing microbial activity. To investigate the eventual coupling between the iron and sulfur cycles in these environments, shallow sediment cores (Congo River deep-sea fan ( 5000 m) were profiled using a combination of geochemical methods. Interestingly, metal reduction dominated suboxic carbon remineralization processes in most of these sediments, while dissolved sulfide was absent. In some 'hotspot' patches, however, sulfate reduction produced large sulfide concentrations which supported chemosynthetic-based benthic megafauna. These environments were characterized by sharp geochemical boundaries compared to the iron-rich background environment, suggesting that FeS precipitation efficiently titrated iron and sulfide from the pore waters. A companion study demonstrated that methanogenesis was active in the deep sediment layers of these patchy ecosystems, suggesting that sulfate reduction was promoted by alternative anaerobic processes. These highly reduced habitats could be fueled by discrete, excess inputs of highly labile natural organic matter from Congo River turbidites or by exhumation of buried sulfide during channel flank erosion and slumping. Sulfidic conditions may be maintained by the mineralization of decomposition products from local benthic macrofauna or bacterial symbionts or by the production of more crystalline Fe(III) oxide phases that are less thermodynamically favorable than sulfate reduction in these bioturbated sediments. Overall, the iron and sulfur biogeochemical cycling in this environment is unique and much more similar to a coastal ecosystem than a deep-sea environment.

  15. Depositional environment and sedimentary of the basinal sediments in the Eibiswalder Bucht (Radl Formation and Lower Eibiswald Beds), Miocene Western Styrian Basin, Austria

    Science.gov (United States)

    Stingl, K.

    1994-12-01

    The Eibiswald Bucht is a small subbasin of the Western Styrian Basin exposing sediments of Lower Miocene age. In the past the entire sequence exposed in the Eibiswalder Bucht has been interpreted as being of fluvial/lacustrine origin; here, results are presented of detailed sedimentological investigations that lead to a revision of this concept. The lowermost siliciclastic sedimentary unit of the Eibiswalder Bucht sequence is the Radl Formation. It is overlain by the Eibiswald Beds, which are subdivided into the Lower, Middle and Upper Eibiswald Beds. The Radl Formation and the Lower Eibiswald Beds are interpreted as a fan delta complex deposited along NNW-SSE striking faults. Based on the sedimentary facies this fan delta can be subdivided into a subaerial alluvial fan facies group, a proximal delta facies group and a distal delta/prodelta facies group. The Radl Formation comprises the alluvial fan and proximal delta facies groups, the Lower Eibiswald Beds the distal delta/prodelta facies group. The alluvial fan and the proximal delta consist of diverse deposits of gravelly flows. The distal delta/prodelta consists of wave-reworked, bioturbated, low density turbidites intercalated with minor gravelly mass flows. The prodelta can be regarded as as the basin facies of the small and shallow Eibiswalder Bucht, where marine conditions prevailed. The basin was probably in part connected with the Eastern Styrian Basin, the contemporary depositional environment of the Styrian Schlier (mainly turbiditic marine offshore sediments in the Eastern Styrian Basin). Analysis of the clast composition, in conjunction with the paleotransport direction of the coarse delta mass flows of the Radl Formation, shows that the source rocks were exclusively crystalline rocks ranging from greenschists to eclogites.

  16. The roles of physical mixing and biochemical composition on the depositional characteristics of flocculated suspended sediment in the Eden estuary, Scotland

    Science.gov (United States)

    Hope, Julie; Manning, Andrew; Aspden, Rebecca; Baas, Jaco; Paterson, David

    2015-04-01

    Sediment load in estuarine waters is generally composed of a mixture of sand, clay and biological matter and it is recognised that there is strong mediation of the physical behaviour of flocs by biological components of the system. Extracellular polymeric substances (EPS) secreted by benthic and pelagic bacteria and algae are a key variable influencing flocculation processes. Variation in the nature and concentration of polymers can alter sediment stability and transport in mixed sediment beds but these substances can also significantly enhance inter-particle cohesion in the water column and therefore deposition and transport. This study examined the variation in naturally occurring EPS concentration and its influence on several physical variables of flocs within the Eden Estuary, Scotland. Samples were collected for total suspended sediment and colormetric analysis of polymer concentration. Subsamples were transferred to the settling column of the LabSFLOC-2 - Laboratory Spectral Flocculation Characteristics -high resolution video floc camera system (Manning, 2006) where settling flocs were viewed (resolution~10μm) to determine floc size (D) and settling velocity (Ws) characteristics. Preliminary results indicate a wide range of microfloc (D160mm) fractions present, with the latter approaching 1 mm during flocculation conducive conditions. Correspondingly, when considering all floc samples, floc settling velocities generally spanned three orders of magnitude with floc size and settling velocities correlating with polymer concentrations. These typically ranged from slow settling (Ws of 0.01-0.05 mm.s-1) predominantly organically based microflocs to faster settling, significantly larger and more porous Macroflocs settling at ~10-15 mm.s-1. The temporal distributions of D and Ws, sediment and polymer concentrations, and the sugar composition of the polymers in suspension are examined in the paper with variation also related to physical and microbiological factors in

  17. Use of reservoir deposits to reconstruct the recent changes in sediment yields from a small granite catchment in the Yimeng Mountain region, China

    Science.gov (United States)

    Zhang, Yunqi; Long, Yi; Li, Bao; Xu, Shujian; Wang, Xiaoli; Liao, Jia

    2017-09-01

    Information on recent changes in sediment yields from small catchments provides a better understanding of temporal trends in soil loss from certain physical and human-influenced landscapes that have been subjected to recent environmental changes, and will help bridge the current knowledge gap that exists between hillslope erosion and sediment transport in rivers. The Yimeng Mountain region, characterized by alternating granite and limestone, is one of the most susceptible regions to soil erosion in northern China, and has been subjected to intensive anthropogenic activity in recent years. Soil loss from areas underlain by granite is particularly obvious, and is the main sediment source for the Yihe River. In this study, we used reservoir deposits to estimate the changes in sediment yields over the past 50 years from a small catchment underlain by granite, namely the Jiangzhuang catchment in the Yimeng Mountain region. Three cores were collected from the Jiangzhuang Reservoir in the catchment. The activities of 137Cs and 210Pbex at different depths, clay (grain size reference to human activity and environmental change in the catchment. The chronologies of the cores were established by 137Cs and 210Pbex dating. The area-specific sediment yield (SSY) for different time periods since dam construction was estimated from each core by referring to the original capacity curve of the reservoir. The results indicate that the depth profiles of 137Cs, 210Pbex, clay, and SOC contents in cores from the Jiangzhuang Reservoir reflect the general history of human disturbances on the catchment over the past 50 years. The estimated SSY value from each core for each period ranged from 7.2 ± 2.7 to 23.7 ± 8.3 t ha- 1 y- 1, with a mean of 12.5 ± 4.6 t ha- 1 y- 1. SSY decreased during 1954-1972, and then showed a general tendency to increase. The temporal pattern of the sediment yield largely reflects the history of environmental change influenced by human activity in the catchment.

  18. Evaluation of metals and hydrocarbons in sediments from a tropical tidal flat estuary of Southern Brazil

    International Nuclear Information System (INIS)

    Costa, Eduardo S.; Grilo, Caroline F.; Wolff, George A.; Thompson, Anu; Figueira, Rubens Cesar Lopes; Neto, Renato Rodrigues

    2015-01-01

    Highlights: • Metals and hydrocarbons in estuary mouth showed indication of anthropogenic input. • Metals in estuary mouth were associated with petroleum-derivative hydrocarbons. • Metals were possibly associated with activities that use oil and its derivatives. • Copper was associated with domestic sewage. - Abstract: Although the Passagem Channel estuary, Espírito Santo State, Brazil, is located in an urbanized and industrialized region, it has a large mangrove system. Here we examined natural and anthropogenic inputs that may influence trace metal (Cd, Cr, Cu, Ni, Sc, Pb and Zn) and hydrocarbon (n-alkane and terpane) deposition in three sediment cores collected in the tidal flat zone of the estuary. The cores were also analyzed for carbonate, grain size and stable isotopic composition (δ 13 C org. and δ 15 N total ). Metal enrichment and its association to petroleum hydrocarbons in the surficial sediments of one of the cores, indicate crude oil and derivative inputs, possibly from small vessels and road run-off from local heavy automobile traffic. At the landward sites, the major contributions for metals and hydrocarbons are from natural sources, but in one case, Cu may have been enriched by domestic effluent inputs

  19. Factors controlling present-day tufa dynamics in the Monasterio de Piedra Natural Park (Iberian Range, Spain): depositional environmental settings, sedimentation rates and hydrochemistry

    Science.gov (United States)

    Vázquez-Urbez, M.; Arenas, C.; Sancho, C.; Osácar, C.; Auqué, L.; Pardo, G.

    2010-07-01

    The tufa record and hydrochemical characteristics of the River Piedra in the Monasterio de Piedra Natural Park (NE Spain) were studied for 6 years. The mean discharge of this river was 1.22 m3/s. The water was supersaturated with calcium carbonate. The HCO3 -, Ca2+ and TDIC concentrations decreased along the 0.5-km-long studied stretch, whereas the calcite SI showed no systematic downstream or seasonal variation over the same stretch. Several sedimentary subenvironments exist in which four broad types of tufa facies form: (1) Dense laminated tufa (stromatolites), (2) Dense to porous, massive tufa, (3) Porous, coarsely laminated tufa with bryophytes and algae, and (4) Dense, hard, laminated deposits in caves. The half-yearly period thickness and weight of sediment accumulated on 14 tablets installed in several subenvironments showed that the deposition rate was greater in fast flowing river areas and in stepped waterfalls, and lower in slow flowing or standing river areas and in spray and splash areas. Mechanical CO2 outgassing is the main factor controlling calcite precipitation on the river bed and in waterfalls, but this process does not explain the seasonal changes in depositional rates. The deposition rates showed a half-yearly period pattern recorded in all fluvial subenvironments persistent over time (5.26 mm, 0.86 g/cm2 in warm periods; 2.26 mm, 0.13 g/cm2 in cool periods). Mass balance calculations showed higher calcite mass values in warm (21.58 mg/L) than in cool (13.68 mg/L) periods. This biannual variation is mainly attributed to the seasonal differences in temperature that caused changes in inorganic calcite precipitation rate and in biomass and the correlative photosynthetic activity. Tufa sedimentation was therefore controlled by both physicochemical and biological processes. The results of this study may help test depositional rates and their environmental controls and thus assess the climatic and hydrological significance of ancient tufas in semi

  20. Sensitivity-Based Modeling of Evaluating Surface Runoff and Sediment Load using Digital and Analog Mechanisms

    Directory of Open Access Journals (Sweden)

    Olotu Yahaya

    2014-07-01

    Full Text Available Analyses of runoff- sediment measurement and evaluation using automated and convectional runoff-meters was carried out at Meteorological and Hydrological Station of Auchi Polytechnic, Auchi using two runoff plots (ABCDa and EFGHm of area 2m 2 each, depth 0.26 m and driven into the soil to the depth of 0.13m. Runoff depths and intensities were measured from each of the positioned runoff plot. Automated runoff-meter has a measuring accuracy of ±0.001l/±0.025 mm and rainfall depth-intensity was measured using tipping-bucket rainguage during the period of 14-month of experimentation. Minimum and maximum rainfall depths of 1.2 and 190.3 mm correspond to measured runoff depths (MRo of 0.0 mm for both measurement approaches and 60.4 mm and 48.9 mm respectively. Automated runoffmeter provides precise, accurate and instantaneous result over the convectional measurement of surface runoff. Runoff measuring accuracy for automated runoff-meter from the plot (ABCDa produces R 2 = 0.99; while R 2 = 0.96 for manual evaluation in plot (EFGHm. WEPP and SWAT models were used to simulate the obtained hydrological variables from the applied measurement mechanisms. The outputs of sensitivity simulation analysis indicate that data from automated measuring systems gives a better modelling index and such could be used for running robust runoff-sediment predictive modelling technique under different reservoir sedimentation and water management scenarios.

  1. On luminescence bleaching of tidal channel sediments

    DEFF Research Database (Denmark)

    Fruergaard, Mikkel; Pejrup, Morten; Murray, Andrew S.

    2015-01-01

    We investigate the processes responsible for bleaching of the quartz OSL signal from tidal channel sediment. Tidal dynamics are expected to play an important role for complete bleaching of tidal sediments. However, no studies have examined the amount of reworking occurring in tidal channels...... and on tidal flats due to the mixing caused by currents and waves. We apply bed level data to evaluate the amount of vertical sediment reworking in modern tidal channels and at a tidal flat. Cycles of deposition and erosion are measured with a bed level sensor, and the results show that gross sedimentation...... was several times higher than net sedimentation. We propose that tidal channel sediment is bleached either on the tidal flat before it is transported to the tidal channels and incorporated in channel-fill successions or, alternatively, on the shallow intertidal part of the channel banks. Based...

  2. Evaluation of PCB bioaccumulation by Lumbriculus variegatus in field-collected sediments

    Science.gov (United States)

    Sediment bioaccumulation tests with Lumbriculus variegatus were performed on polychlorinated biphenyl (PCBs) contaminated sediment samples from the Hudson, Grasse, and Fox Rivers Superfund sites with concurrent measurement of PCB concentrations in sediment interstitial water. Th...

  3. The origin of dose distributions in fluvial sediments, and the prospect of dating single grains from fluvial deposits using optically stimulated luminescence

    International Nuclear Information System (INIS)

    Olley, J.M.; Caitcheon, G.G.; Roberts, R.G.

    1999-01-01

    We examine the causes of the asymmetric distributions of dose observed from measurements of the optically stimulated luminescence emitted by small aliquots of fluvial quartz, and deduce that the asymmetry arises as a result of samples being composed of a mix of mainly well bleached grains with grains that were effectively unbleached at the time of deposition. We demonstrate that the shapes of the dose distributions can be used to assess the likelihood that aliquots consist only of grains that were well-bleached at the time of deposition. The more asymmetric the distribution, the greater the probability that the aliquots with the lowest dose most closely represent the true burial dose. Single grains with differing doses are present in each of the samples examined, and the population with the lowest dose gives an optical age consistent with the expected burial age. This result implies that the beta-dose heterogeneity in these deposits is small, and that the effects of micro-dosimetric variations on optical dating of individual grains are not significant for these samples. We demonstrate that single-grain dating of fluvial material is possible and practicable using standard Risoe optical dating equipment, and we conclude that application of a new regenerative-dose protocol to single grains of quartz, using the lowest dose population to estimate the burial dose, is the best available means of obtaining reliable luminescence ages for heterogeneously bleached fluvial sediments

  4. Soils and organic sediments

    International Nuclear Information System (INIS)

    Head, M.J.

    1999-01-01

    The organic component of soils is basically made up of substances of an individual nature (fats, waxes, resins, proteins, tannic substances, and many others), and humic substances (Kononova, 1966). These are complex polymers formed from breakdown products of the chemical and biological degradation of plant and animal residues. They are dark coloured, acidic, predominantly aromatic compounds ranging in molecular weight from less than one thousand to tens of thousands (Schnitzer, 1977). They can be partitioned into three main fractions:(i) Humic acid, which is soluble in dilute alkaline solution, but can be precipitated by acidification of the alkaline extract.(ii) Fulvic acid, which is soluble in alkaline solution, but is also soluble on acidification.(iii) Humin that cannot be extracted from the soil or sediment by dilute acid or alkaline solutions. It has mostly been assumed that the humic and fulvic acid components of the soil are part of the mobile, or 'active' component, and the humin component is part of the 'passive' component. Other types of organic sediments are likely to contain chemical breakdown products of plant material, plant fragments and material brought in from outside sources. The outside material can be contemporaneous with sediment deposition, can be older material, or younger material incorporated into the sediment long after deposition. Recognition of 'foreign' material is essential for dating, but is not an easy task. Examples of separation techniques for humic and non humic components are evaluated for their efficiency

  5. Source Evaluation and Trace Metal Contamination in Benthic Sediments from Equatorial Ecosystems Using Multivariate Statistical Techniques.

    Directory of Open Access Journals (Sweden)

    Nsikak U Benson

    Full Text Available Trace metals (Cd, Cr, Cu, Ni and Pb concentrations in benthic sediments were analyzed through multi-step fractionation scheme to assess the levels and sources of contamination in estuarine, riverine and freshwater ecosystems in Niger Delta (Nigeria. The degree of contamination was assessed using the individual contamination factors (ICF and global contamination factor (GCF. Multivariate statistical approaches including principal component analysis (PCA, cluster analysis and correlation test were employed to evaluate the interrelationships and associated sources of contamination. The spatial distribution of metal concentrations followed the pattern Pb>Cu>Cr>Cd>Ni. Ecological risk index by ICF showed significant potential mobility and bioavailability for Cu, Cu and Ni. The ICF contamination trend in the benthic sediments at all studied sites was Cu>Cr>Ni>Cd>Pb. The principal component and agglomerative clustering analyses indicate that trace metals contamination in the ecosystems was influenced by multiple pollution sources.

  6. Stylolites, porosity, depositional texture, and silicates in chalk facies sediments:Ontong Java Plateau - Gorm and Tyra fields, North Sea

    OpenAIRE

    Fabricius, Ida Lykke; Borre, Mai K.

    2007-01-01

    Comparison of chalk on the Ontong Java Plateau and chalk in the Central North Sea indicates that, whereas pressure dissolution is controlled by effective burial stress, pore-filling cementation is controlled by temperature. Effective burial stress is caused by the weight of all overlying water and sediments as counteracted by the pressure in the pore fluid, so the regional overpressure in the Central North Sea is one reason why the two localities have different relationships between temperatu...

  7. Post-depositional reactivity of the plutonium in different sediment facies from the English channel - an experimental approach

    International Nuclear Information System (INIS)

    Gouzy, A.; Boust, D.; Klein, A.

    2004-01-01

    The plutonium discharged into sea (in particular resulting from the activity of the reprocessing plants of nuclear fuels) presents a great affinity for the sedimentary particles. In the English Channel, the weakness of the plutonium concentrations met in the natural environment makes very difficult a direct study of the diagenetic phenomena which influences on the behavior of this radionuclide after its incorporation to the sedimentary column. On the scale of the all English Channel, the stock of plutonium immobilized in the sediments is significant (some TBq), this fact justifies the study of its becoming. With this intention, we constructed a set of experiments on series marine sediments with various sedimentological facies, which have been spiked with plutonium. After a one-month incubation period, various parameters describing the behavior of plutonium were given: (1) distribution of plutonium between the particulate phases and the pore waters; (2) quantification of plutonium associated with reactive sulphides; (3) distribution of plutonium between the particles and the seawater during a sediment resuspension episode. (author)

  8. Evaluating spatial patterns of dioxins in sediments to aid determination of potential implications for marine reptiles

    Energy Technology Data Exchange (ETDEWEB)

    Hermanussen, S.; Gaus, C. [National Research Centre for Environmental Toxicology, Brisbane (Australia); Limpus, C.J. [Queensland Environmental Protection Agency, Brisbane (Australia); Paepke, O. [ERGO Forschungsgesellschaft mbH, Hamburg (Germany); Blanshard, W. [Sea World, Gold Coast (Australia); Connell, D. [School of Public Health, Griffith Univ., Brisbane (Australia)

    2004-09-15

    Recent investigations have identified elevated concentrations of polychlorinated dibenzo-p-dioxins (dioxins) in marine sediments and wildlife of Queensland, Australia. While it has been demonstrated that the contamination is widespread and predominantly land-based, limited information exists on the pathways and fate of these compounds within the near-shore marine system. This environment supports unique and threatened species including green sea turtles (Chelonia mydas). Adult green turtles are predominantly herbivorous, feeding on seagrass and algae. Apart from initial migration to feeding grounds (at {proportional_to}10 years of age) and intermittent migrations to breeding grounds (at {proportional_to}30-50 years and thereafter), green turtles remain and feed within relatively small home ranges. Long life-span (50 years or more), near-shore feeding grounds and highly specialized food requirements render green turtles potentially vulnerable to contaminant exposure. Recent studies have shown a relationship between PCDD/F concentrations found in herbivorous marine wildlife and concentrations in sediments of their habitats. Hence, the spatial evaluation of sediment PCDD/F distribution may assist the assessment of green turtle exposure and its potential implications. The present study provides baseline information on green turtle PCDD/F concentrations in Queensland, Australia and investigates exposure pathways. In addition, spatial distribution of PCDD/Fs in sediments from known green turtle feeding regions is assessed using geographic information systems. This represents the first stage of a large scale investigation into the exposure and sensitivity of marine reptiles to dioxins and dioxin-like compounds and to evaluate whether poor health status observed in some populations may be related to contaminant exposure.

  9. Evaluation of Wetland Creation with John F. Baldwin Ship Channel Sediment

    National Research Council Canada - National Science Library

    Led, C

    2000-01-01

    .... Sediments were sampled and tested to determine the physical and chemical characteristics. Little sediment contamination was found except for elevated levels of polycyclic aromatic hydrocarbons (PAHs...

  10. Mosses as an integrating tool for monitoring PAH atmospheric deposition: comparison with total deposition and evaluation of bioconcentration factors. A year-long case-study.

    Science.gov (United States)

    Foan, Louise; Domercq, Maria; Bermejo, Raúl; Santamaría, Jesús Miguel; Simon, Valérie

    2015-01-01

    Polycyclic aromatic hydrocarbon (PAH) atmospheric deposition was evaluated at a remote site in Northern Spain using moss biomonitoring with Hylocomium splendens (Hedw.) Schimp., and by measuring the total deposition fluxes of PAHs. The year-long study allowed seasonal variations of PAH content in mosses to be observed, and these followed a similar trend to those of PAH fluxes in total deposition. Generally, atmospheric deposition of PAHs is greater in winter than in summer, due to more PAH emissions from domestic heating, less photoreactivity of the compounds, and intense leaching of the atmosphere by wet deposition. However, fractionation of these molecules between the environmental compartments occurs: PAH fluxes in total deposition and PAH concentrations in mosses are correlated with their solubility (r=0.852, pPAH fluxes can be estimated with moss biomonitoring data if the bioconcentration or 'enriching' factors are known. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. The dirt on sediments

    Science.gov (United States)

    Smith, Loren M.; Euliss, Ned H. "Chip"

    2010-01-01

    In the wetland science field, sediment deposition is often thought of as being beneficial especially when one thinks of coastal estuarine systems. For example, sediments deposited from streams and rivers are necessary to naturally build and maintain tidal marshes. These sediments come from eroded upland soils in the interior of the continent. When these sediments are diverted from natural coastal deposition areas, such as occurs from river channelization, we lose marshes through subsidence as is happening throughout coastal Louisiana. However, the value of eroded soils is all a matter of hydrogeomorphic perspective.

  12. Evaluation of burnup characteristics and energy deposition during NSRR pulse irradiation tests on irradiated BWR fuels

    International Nuclear Information System (INIS)

    Nakamura, Takehiko; Yoshinaga, Makio

    2000-11-01

    Pulse irradiation tests of irradiated fuel are performed in the Nuclear Safety Research Reactor (NSRR) to investigate the fuel behavior under Reactivity Initiated Accident Conditions (RIA). The severity of the RIA is represented by energy deposition or peak fuel enthalpy during the power excursion. In case of the irradiated fuel tests, the energy deposition varies depending both on the amounts and distribution of residual fissile and neutron absorbing fission products generated during the base irradiation. Thus, proper fuel burnup characterization, especially for low enriched commercial fuels, is important, because plutonium (Pu) takes a large part of fissile and its generation depends on the neutron spectrum during the base irradiation. Fuel burnup calculations were conducted with ORIGEN2, RODBURN and SWAT codes for the BWR fuels tested in the NSRR. The calculation results were compared with the measured isotope concentrations and used for the NSRR neutron calculations to evaluate energy depositions of the test fuel. The comparison of the code calculations and the measurements revealed that the neutron spectrum change due to difference in void fraction altered Pu generation and energy deposition in the NSRR tests considerably. With the properly evaluated neutron spectrum, the combined burnup and NSRR neutron calculation gave reasonably good evaluation of the energy deposition. The calculations provided radial distributions of the fission product accumulation during the base irradiation and power distribution during the NSRR pulse irradiation, which were important for the evaluation of both burnup characteristics and fission gas release behavior. (author)

  13. Bedform reconstruction using Terrestrial Laser Scanning at Hunt's Hole, New Mexico: implications for sediment transport in pyroclastic surge deposits and criteria for their identification on Mars

    Science.gov (United States)

    Edgar, L.; Grotzinger, J. P.; Ewing, R. C.; Southard, J. B.; Lamb, M. P.

    2011-12-01

    Pyroclastic surges are dilute flows of gas and rock fragments, typically generated by the interaction of magma and water. Due to their hazardous nature, very little is known about sediment transport during these eruptions. However, the cross-stratified deposits that they leave behind provide an important record of flow conditions, if properly interpreted. In the absence of geologic context (and volcanic indicators such as bombs and lapilli), it may be difficult to distinguish bedforms in pyroclastic surge deposits from those in eolian or fluvial deposits. There has been some debate about the identification of pyroclastic surge deposits on Mars, suggesting a need to establish better criteria for recognizing these deposits in remote sensing applications. The goals of this study are to use physical characteristics to better understand bedform kinematics and gain insight into the flow dynamics of pyroclastic surges, and to establish criteria to distinguish pyroclastic surges from other depositional environments on Mars. Two examples of pyroclastic surge deposits are exposed in Hunt's Hole (HH) and Kilbourne Hole in southern NM. These volcanic craters expose up to 13 m of stratigraphy, dominated by dm-to-m-scale bedforms. The geomorphic pattern around the rim of HH provides 3D exposures at the scale of the bedforms, which enables observations of bedform geometries. We identify several facies, and measure bedform characteristics in the cross-stratified facies. Bedforms range in height from 25-80 cm, and wavelength from 190-460 cm. Stoss slope angles range from 4-11°, and lee slope from 2-18°. Geometries indicate possible bedform merging, as smaller bedforms overtake others to build larger features. Bedform interactions have been described in modern eolian systems, typically in plan-view, but these surge deposits may provide an opportunity to observe them in outcrop in cross-section. We propose that bedforms in pyroclastic surges can be identified by a unique style of

  14. Geochemistry of Mine Waste and Mill Tailings, Meadow Deposits, Streambed Sediment, and General Hydrology and Water Quality for the Frohner Meadows Area, Upper Lump Gulch, Jefferson County, Montana

    Science.gov (United States)

    Klein, Terry L.; Cannon, Michael R.; Fey, David L.

    2004-01-01

    Frohner Meadows, an area of low-topographic gradient subalpine ponds and wetlands in glaciated terrane near the headwaters of Lump Gulch (a tributary of Prickly Pear Creek), is located about 15 miles west of the town of Clancy, Montana, in the Helena National Forest. Mining and ore treatment of lead-zinc-silver veins in granitic rocks of the Boulder batholith over the last 120 years from two sites (Frohner mine and the Nellie Grant mine) has resulted in accumulations of mine waste and mill tailings that have been distributed downslope and downstream by anthropogenic and natural processes. This report presents the results of an investigation of the geochemistry of the wetlands, streams, and unconsolidated-sediment deposits and the hydrology, hydrogeology, and water quality of the area affected by these sources of ore-related metals. Ground water sampled from most shallow wells in the meadow system contained high concentrations of arsenic, exceeding the Montana numeric water-quality standard for human health. Transport of cadmium and zinc in ground water is indicated at one site near Nellie Grant Creek based on water-quality data from one well near the creek. Mill tailings deposited in upper Frohner Meadow contribute large arsenic loads to Frohner Meadows Creek; Nellie Grant Creek contributes large arsenic, cadmium, and zinc loads to upper Frohner Meadows. Concentrations of total-recoverable cadmium, copper, lead, and zinc in most surface-water sites downstream from the Nellie Grant mine area exceeded Montana aquatic-life standards. Nearly all samples of surface water and ground water had neutral to slightly alkaline pH values. Concentrations of arsenic, cadmium, lead, and zinc in streambed sediment in the entire meadow below the mine waste and mill tailings accumulations are highly enriched relative to regional watershed-background concentrations and exceed consensus-based, probable-effects concentrations for streambed sediment at most sites. Cadmium, copper, and

  15. Development and evaluation of a long-term deposit probe for on-line monitoring of deposit growth

    Energy Technology Data Exchange (ETDEWEB)

    Brink, Anders; Lauren, Tor; Yrjas, Patrik; Hupa, Mikko [Process Chemistry Centre, Aabo Akademi University, Biskopsgatan 8, FI-20540 Turku (Finland); Friesenbichler, Joachim [Institute for Resource Efficient and Sustainable Systems, Technical University Graz Inffeldg. 21b, A-8010 Graz (Austria)

    2007-12-15

    A newly designed air-cooled probe for on-line monitoring of deposition growth has been tested in a boiler firing three woody fuels. Thermocouples are mounted on both sides of the tube wall enabling measurements of the heat flux through the probe wall. Knowing the heat flux through the probe wall, it is possible to measure the additional heat transfer resistance caused by the deposit and to estimate the properties of the deposit. Calculating the deposit thickness using the collected temperature data indicated the thinnest deposit when wood was fired, followed by bark and waste wood. The calculated deposit thickness was larger than those found when analysing the deposit thickness after the probe had been removed. Nevertheless, the ranking of fuels by deposit build-up rate was the same. (author)

  16. Microcosms for evaluating microbial indicator persistence and mobilization in fluvial sediments during rainfall events.

    Science.gov (United States)

    Martín-Díaz, Julia; García-Aljaro, Cristina; Pascual-Benito, Míriam; Galofré, Belén; Blanch, Anicet R; Lucena, Francisco

    2017-10-15

    Mediterranean rivers, which are subject to long, dry periods and heavy rainfall events, could be particularly useful for understanding future climate scenarios. This study generated microcosms that mimicked riverbank sediment resuspension into the water of a typical Mediterranean river as a consequence of heavy rainfall. The mobilization and inactivation of six fecal pollution indicators and microbial source tracking markers were evaluated. The T 90 values in the sediments were: 4 days for sorbitol-fermenting Bifidobacterium, 11 days for culturable E. coli, 36 days for bacteriophages infecting Bacteroides thetaiotaomicron strain GA17 and more than 42 days for qPCR-detected E. coli, somatic coliphages and sulfite-reducing clostridia spores. Bacteriophages and bacteria showed different resuspension and sedimentation patterns. The data obtained could be used in predictive models to assess the effects of climate change on surface water quality. Pathogen mobilization into the water column poses a risk for humans, animals and the natural environment, and breaches the One Health approach. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Growth of superconducting Bi2Sr2CaCu2O8+δ films by sedimentation deposition and liquid phase sintering and annealing technique

    International Nuclear Information System (INIS)

    Manahan, R.L.C.; Sarmago, R.V.

    2006-01-01

    We report on a technique of growing highly c-axis oriented Bi 2 Sr 2 CaCu 2 O 8+δ (Bi-2212) thick films on MgO substrate using a combined sedimentation-deposition and liquid phase sintering and annealing process. The temperature profiles employed partial melting followed by rapid cooling to temperature below the melting point. Scanning electron micrographs show that the films have a smooth surface. No evidence of grain boundaries on the film's surface can be seen. The critical temperatures of the samples range from ∼67 K to ∼81 K. This method presents a quick and easy preparation for high quality epitaxial Bi-2212 films

  18. Geochemical Indicators of the Carbonate Sedimentation Depositional Environments and Geodynamic Conditions in the East of the Middle Urals in the Kizelovian Time

    Directory of Open Access Journals (Sweden)

    S. A. Dub

    2017-12-01

    Full Text Available Geochemical characteristics of the limestones of Kizelovskian substage of the Eastern Urals zone (Rezh River, Middle Urals, such as carbon and oxygen isotopic composition, concentration of minor and trace elements, and redox value indicators, were studied in details. Based on the results of data interpretation and analysis of lithological features, it was assumed that carbonate deposits formed in shallow oxygen-rich environment with high bioproductivity warm water ecosystem, and within the isolated carbonate platform with a steady sinking territory. Some signs indicate that sedimentation during the Kizelovian time occurred in the inner lagoon of a large atoll. The Maldivian archipelago could be a contemporary analogue of the Rezhevskaya carbonate platform.

  19. Grain size distribution of road-deposited sediment and its contribution to heavy metal pollution in urban runoff in Beijing, China.

    Science.gov (United States)

    Zhao, Hongtao; Li, Xuyong; Wang, Xiaomei; Tian, Di

    2010-11-15

    Pollutant washoff from road-deposited sediment (RDS) is an increasing problem associated with the rapid urbanization of China that results in urban non-point source pollution. Here, we analyzed the RDS grain size distribution and its potential impact on heavy metal pollution in urban runoff from impervious surfaces of urban villages, colleges and residences, and main traffic roads in the Haidian District, Beijing, China. RDS with smaller grain size had a higher metal concentration. Specifically, particles with the smallest grain size (runoff water accounted for greater than 70% of the metal mass in the total suspended solids (TSS). The heavy metal content in the TSS was 2.21-6.52% of that in the RDS. These findings will facilitate our understanding of the importance of RDS grain size distribution in heavy metal pollution caused by urban storm runoff. Copyright © 2010 Elsevier B.V. All rights reserved.

  20. A critical evaluation of depositional parameters controlling the variability of organic carbon in Arabian Sea sediments

    Digital Repository Service at National Institute of Oceanography (India)

    Paropkari, A.L.; PrakashBabu, C.; Mascarenhas, A.

    source of organic matter. However, a critical examination reveals that the organic enrichment on the slope of the Indian margin is two to four fold higher (max. 16.71%) than on the slope of the Arabian Peninsula (max. 7.54%) while the productivity...

  1. A economic evaluation system software on in-situ leaching mining sandstone uranium deposits

    International Nuclear Information System (INIS)

    Yao Yixuan; Su Xuebin; Xie Weixing; Que Weimin

    2001-01-01

    The author presents the study results of applying computer technology to evaluate quantitatively the technical-economic feasibility of in-situ leaching mining sandstone uranium deposits. A computer system software have been developed. Under specifying deposit conditions and given production size per year, the application of the software will generate total capital and mine life operating costs as well as solve for the movable and static financial assessment targets through discounted cash flow analysis. According to the characters of two kinds of sandstone uranium deposits, a data bases of economic and technique parameters of in-situ leaching have been designed. Also the system software can be used to study the economic value of deposits and to optimize the key project parameters. Its features, data input method and demand, main functions, structure and operating environments are described

  2. [Heavy metals distribution characteristics and ecological risk evaluation in surface sediments of dammed Jinshan lake].

    Science.gov (United States)

    Zhou, Xiao-Hong; Liu, Long-Mei; Chen, Xi; Chen, Zhi-Gang; Zhang, Jin-Ping; Li, Yi-Min; Liu, Biao

    2014-11-01

    In order to reveal the pollution loading of heavy metals in Dammed Jinshan lake, six heavy metals (As, Cu, Pb, Cd, Zn, Cr) from 18 sediment samples were analyzed using ICP, and the distribution characteristics of heavy metals in the sediment were comprehensively evaluated through concentration coefficient, geo-acumulation indexes, potential ecological risk evaluation and traceability analysis. The results showed that (1) the average contents of As, Pb, Cu, Zn, Cr, Cd were 23.22, 26.20, 24.42, 143.12, 245.30 and 0.67 mg x kg(-1), respectively, in the surface sediments of dammed Jinshan Lake. The average contents of Pb and Cu were lower than the primary standard and secondary standards of soil environmental quality standards. The average contents of Zn and Cr were lower than the primary standard and higher than the secondary standards of soil environmental quality standards. The average contents of As and Cd were higher than the primary and secondary standards of soil environmental quality standards. From the spatial distribution, the contents of Pb and Zn were the highest at sampling site No. 1, which was located at the Beigushan Square. The contents of As,Cu, Cr, Cd were the highest at sampling sites Nos. 12, 3, 14, and 7, respectively; (2) The order of concentration coefficient was As > Cr > Cd > Pb > Zn > Cu, which indicated that the enrichment amount of As was the highest and that of Cu was the lowest; (3) Based on the geo-acumulation indexes, the Cu is clean and Pb, Zn, Cd is the light pollution and As, Cr moderate pollution; (4) The order of Potential ecological risk coefficient was Cd > As > Cr > Pb > Cu > Zn, Cr, Pb, Cu, Zn were of light ecological risk and As, Cd were of medium ecological risk. From the spatial distribution, the sampling sites Nos. 1, 6, 7 and 12 had medium potential ecological risk, and the rest sample points had slight potential ecological risk; (5) The principal component analysis (PCA) revealed that the main reason for the differences

  3. Bioremediation of Contaminated Lake Sediments and Evaluation of Maturity Indicies as Indicators of Compost Stability

    Directory of Open Access Journals (Sweden)

    Y. Anjaneyulu

    2005-08-01

    Full Text Available Land contamination is one of the widely addressed problems, which is gaining importance in many developed and developing countries. International efforts are actively envisaged to remediate contaminated sites as a response to adverse health effects. Popular conventional methodologies only transfer the phase of the contaminant involving cost intensive liabilities besides handling risk of the hazardous waste. Physico-chemical methods are effective for specific wastes, but are technically complex and lack public acceptance for land remediation. “Bioremediation”, is one of the emerging low-cost technologies that offer the possibility to destroy various contaminants using natural biological activities. Resultant non -toxic end products due to the microbial activity and insitu applicability of this technology is gaining huge public acceptance. In the present study, composting is demonstrated as a bioremediation methodology for the stabilization of contaminated lake sediments of Hyderabad, A.P, India. Lake sediment contaminated with organics is collected from two stratums – upper (0.25 m and lower (0.5m to set up as Pile I (Upper and Pile II (Lower in the laboratory. Lime as a pretreatment to the lake sediments is carried out to ensure metal precipitation. The pretreated sediment is then mixed with organic and inorganic fertilizers like cow dung, poultry manure, urea and super phosphate as initial seeding amendments. Bulking agents like sawdust and other micronutrients are provided. Continuous monitoring of process control parameters like pH, moisture content, electrical conductivity, total volatile solids and various forms of nitrogen were carried out during the entire course of the study. The stability of the compost was evaluated by assessing maturity indices like C/N, Cw (water soluble carbon, CNw (Cw/Nw, nitrification index (NH4/NO-3, Cation Exchange Capacity (CEC, germination index, humification ratio, compost

  4. Soft-sediment deformation structures interpreted as seismites in the uppermost Aptian to lowermost Albian transgressive deposits of the Chihuahua basin (Mexico)

    Science.gov (United States)

    Blanc, E.J.-P.; Blanc-Aletru, M. -C.; Mojon, P.-O.

    1998-01-01

    Several levels of soft-sediment deformation structures (s.-s.d.s.) cut by synsedimentary normal faults have been observed in the transition beds between the "Las Vigas" and "La Virgen" formations (Cretaceous) in the northeastern part of the Chihuahua basin in Mexico. These structures consisted of four kinds of motifs (floating breccias, flame-like structures, large pillow structures, and wavy structures). They are restricted to five "stratigraphie" levels (Z1-Z5) and surrounded by undeformed beds in fluvio-lacustrine and tidal deposits and can be traced over a distance of several hundred meters. This deformation is interpreted to have resulted from the combined effects of liquidization and shear stress in soft-sediments due to local earthquakes in the area which could have been generated during the rifting stage of the Chihuahua basin. New constraints placed on the age of the "Las Vigas" Formation (bracketed by Late Aptian charophytes at the bottom and colomiellids of late Aptian to earliest Albian age at the top) suggest that this synrift tectonism lasted at least until the end of the Aptian. ?? Springer-Verlag 1998.

  5. Evaluation of the distribution of rare earths elements in fluvial sediments, rocks and wastes correlated to the Caldas Ore Treatment Unit (UTM-Caldas), Minas Gerais State, Brazil

    International Nuclear Information System (INIS)

    Possas, Clara R.; Moura, Rodrigo R. de; Carvalho Filho, Carlos A. de; Menezes, Maria Ângela de B.C.

    2017-01-01

    The Caldas Ore Treatment Unit (UTM-Caldas), located at the municipality of Caldas (Minas Gerais-Brazil), was a site for the exploration and treatment of uranium between 1982 and 1995. The area is located in the Alcalino Complex of Poços de Caldas, a geologically peculiar region, composed of alkaline igneous rocks with exotic minerals, some rich in rare earth elements (REE). The UTM-Caldas uranium deposit was defined as a U, Th, Zr, Mo and REE mineralization. The objective of the present study was to evaluate the distribution of REEs in river sediments adjacent to UTM-Caldas and to verify if effluents from the mine are interfering in the concentration of REEs in these sediments. To develop the research, five samples were collected in 2011, including sediments from the Soberbo river, the waste dam and the tank of radio precipitation. The samples were prepared in the Sedimentology Laboratory of the Center for the Development of Nuclear Technology (CDTN), where the rocks and tailings were crushed, ground and pulverized while the sediments were sieved and an aliquot of the silt-clay fraction was separated for analysis at the CDTN. The analytical method employed was Neutron Activation Analysis (ANA), method k 0 . The samples were irradiated in the TRIGA MARK I IPR-R1 research reactor, and the REEs identified by gamma-spectrometry in the Neutron Activation Laboratory (LAN-CDTN). The results showed a distribution model of the REEs in the study area, which may be useful in evaluating of the environmental impacts of effluents from UTM-Caldas, now in the process of decommissioning

  6. How depositional conditions control input, composition, and degradation of organic matter in sediments from the Chilean coastal upwelling region

    DEFF Research Database (Denmark)

    Niggemann, Jutta; Ferdelman, Timothy G.; Lomstein, Bente Aagaard

    2007-01-01

    investigated for excess 210Pb (210Pbxs) activity, total organic and total inorganic carbon concentrations (TOC and TIC, respectively), C/N-ratios, organic carbon isotopic compositions (d13C), chlorin concentrations, Chlorin Indices (CI), and sulfate reduction rates (SRR). Sediment accumulation rates obtained...... m‑2 d‑1), which was partly due to the greater water depth of most of the sediments investigated in the northern region and consistent with a lower quality of the sedimentary OM at 23°S. Reaction rate constants for TOC degradation that were obtained from measured SRR (kSRR; 0.0004‑0.0022 yr‑1) showed...... a good correspondence to kTOC that were derived from the depth profiles of TOC (0.0003‑0.0014 yr‑1). Both, kSRR and kTOC, reflect differences in OM composition. At 36°S they were related to the degradation state of bulk OM (represented by C/N-ratios), whereas near 23°S they were related to the freshness...

  7. Zn speciation in a soil contaminated by the deposition of a dredged sediment by synchrotron X-ray techniques

    International Nuclear Information System (INIS)

    Isaure, Marie-Pierre; Manceau, Alain; Laboudigue, Agnes; Tamura, Nobumichi; Marcus, Matthew A.

    2003-09-01

    The nature and proportion of Zn species present in an agricultural soil overlaid by a dredged contaminated sediment have been untangled by the novel combination of three non-invasive synchrotron-based x-ray techniques: x-ray microfluorescence (μSXRF), microdiffraction (μXRD), and absorption spectroscopy (EXAFS). One primary (franklinite) and two secondary (phyllomanganate and phyllosilicate) Zn-containing minerals were identified in the initial soil, and another primary (ZnS) and a new secondary (Fe-(oxyhydr)oxide) Zn species in the covered soil. The quantitative analysis of EXAFS spectra recorded on bulk samples indicated that ZnS and Zn-Fe (oxyhydr)oxides amounted to 71+-10 percent and 27+-10 percent, respectively, and the other Zn species to less than 10 percent. The two new Zn species found in the covered soil result from the gravitational migration of ZnS particles initially present in the sediment, and from their further oxidative dissolution and fixation of leached Zn on F e (oxyhydr) oxides

  8. Toward Synchronous Evaluation of Source Apportionments for Atmospheric Concentration and Deposition of Sulfate Aerosol Over East Asia

    Science.gov (United States)

    Itahashi, S.

    2018-03-01

    Source apportionments for atmospheric concentration, dry deposition, and wet deposition of sulfate aerosol (SO42-) were synchronously evaluated over East Asia, a main source of anthropogenic sulfur dioxide (SO2) emissions. Estimating dry deposition was difficult owing to the difficulty of measuring deposition velocity directly; therefore, sensitivity simulations using two dry deposition schemes were conducted. Moreover, sensitivity simulations for different emission inventories, the largest uncertainty source in the air quality model, were also conducted. In total, four experimental settings were used. Model performance was verified for atmospheric concentration and wet deposition using a ground-based observation network in China, Korea, and Japan, and all four model settings captured the observations. The underestimation of wet deposition over China was improved by an adjusted approach that linearly scaled the modeled precipitation values to observations. The synchronous evaluation of source apportionments for atmospheric concentration and dry and wet deposition showed the dominant contribution of anthropogenic emissions from China to the atmospheric concentration and deposition in Japan. The contributions of emissions from volcanoes were more important for wet deposition than for atmospheric concentration. Differences in the dry deposition scheme and emission inventory did not substantially influence the relative ratio of source apportionments over Japan. Because the dry deposition was more attributed to local factors, the differences in dry deposition may be an important determinant of the source contributions from China to Japan. Verification of these findings, including the dry deposition velocity, is necessary for better understanding of the behavior of sulfur compound in East Asia.

  9. Seasonal Variations and Yearly Trend Evaluations of Sedimentation Loads: A Case Study at Chalok River, Terengganu, Malaysia

    Directory of Open Access Journals (Sweden)

    Aida Soraya Shamsuddin

    2014-01-01

    Full Text Available The aims of this study were to determine the relationship between seasonal variations (wet and dry periods on sedimentation loads and to identify the yearly trend of sedimentation loads at Chalok River, Terengganu, Malaysia from 2003 to 2008. It was found that wet and dry periods influenced the transportation of suspended sediment into the river significantly. The highest suspended sediment loads at Chalok River occurred during the wet period when the intensity of rainfall is high. Besides, the rainfall, water level, stream flow and suspended sediment loads also were analysed using Spearman correlation to identify their relationships. The results showed significant positive relationship between suspended sediment loads with rainfall (r = 0.664, p< 0.05, water level (r = 0.923, p< 0.05 and stream flow (r = 0.919, p< 0.05. Multiple linear regressions revealed 63% of high suspended sediment loads at Chalok River can be explained by rainfall, water level and stream flow. The trends of rainfall, water level, stream flow and suspended sediment loads were analysed by using Mann-Kendall trend test where the results showed that there is a significant increasing trend for suspended sediment loads but no significant increase trend for rainfall, water level and stream flow over the studied periods. It is evident that the evaluations conducted in this study are useful in providing better understanding and reliable conclusion on the basis of seasonal variations and other environmental variables that affect the sedimentations loads in the river. Such effort provides holistic information for effective and wise management policy of river basin management in the future.

  10. Slumping and a sandbar deposit at the Cretaceous-Tertiary boundary in the El Tecolote section (northeastern Mexico): An impact-induced sediment gravity flow

    Science.gov (United States)

    Soria, Ana R.; Liesa, Carlos L.; Mata, Maria Pilar; Arz, José A.; Alegret, Laia; Arenillas, Ignacio; Meléndez, Alfonso

    2001-03-01

    Slumps affecting uppermost Méndez Formation marls, as well as the spherulitic layer and basal part of the sandy deposits of the Cretaceous-Tertiary (K-T) boundary clastic unit, are described at the new K-T El Tecolote section (northeastern Mexico). These K-T clastic deposits represent sedimentation at middle-bathyal water depths in channel and nonchannel or levee areas of reworked materials coming from environments ranging from outer shelf to shallower slope via a unidirectional, high- to low-density turbidite flow. We emphasize the development and accretion of a lateral bar in a channel area from a surging low-density turbidity current and under a high-flow regime. The slumps discovered on land and the sedimentary processes of the K-T clastic unit reflect destabilization and collapse of the continental margin, support the mechanism of gravity flows in the deep sea, and represent important and extensive evidence for the impact effects in the Gulf of México triggered by the Chicxulub event.

  11. Sediment transport and deposition during extreme sea storm events at the Salerno Bay (Tyrrhenian Sea: comparison of field data with numerical model results

    Directory of Open Access Journals (Sweden)

    F. Budillon

    2006-01-01

    Full Text Available Seismic stratigraphy and core litho-stratigraphy in the Salerno Bay inner shelf (Southern Tyrrhenian Sea reveal significant storm deposition episodes over the last 1 ky. Three major events are preserved as decimetre thick silt/sand layers bounded at their base by erosional surfaces and sealed in the muddy marine sequences between 25 and 60 m of depth. Geochronology and chrono-stratigraphy on core sediment point towards a recurrence of major sea storms between 0.1 and 0.3 ky and put the last significant event in the 19th century, when no local meteorological time series is available. A modelling of extreme sea-storms with a return period of about 0.1 ky is here proposed based on historical hindcast and aims at explaining the occurrence of such unusual deep and thick sand deposits in the northern sector of the bay. Results highlight the vulnerability of the northern coast of the Salerno Bay to the south western sea storms which can drive waves up to about 8 m high and wave period of about 13 s. With these conditions an intense combined flow current is formed and might account for winnowing fine sand down to the depth of 40 m at least. The numerical model thus confirms a possible sand transport in the bottom boundary layer due to wave-current interaction and could corroborate the interpretation of the most recent sand layers, included in the cores, as being generated under extreme sea storm conditions.

  12. Bioaccumulation, toxicokinetics, and effects of copper from sediment spiked with aqueous Cu, nano-CuO, or micro-CuO in the deposit-feeding snail, Potamopyrgus antipodarum

    DEFF Research Database (Denmark)

    Pang, Chengfang; Selck, Henriette; Banta, Gary Thomas

    2013-01-01

    The present study examined the relative importance of copper (aqueous Cu and CuO particles of different sizes) added to sediment to determine the bioaccumulation, toxicokinetics, and effects in the deposit feeder Potamopyrgus antipodarum. In experiment 1, the bioaccumulation of Cu (240 mg Cu/g dr...

  13. Using tracer-based sediment budgets to quantify erosion and deposition within harvested forests in south-east NSW, Australia

    International Nuclear Information System (INIS)

    Wallbrink, P.J.; Roddy, B.P.; Olley, J.M.

    1998-01-01

    Full text: The total impact of forest operations on the store of soil material within harvested coupes can be difficult to quantify. A study was recently undertaken in a small (∼12 ha) basin near Bombala, south-east NSW to measure both the net amount of soil erosion from the basin, and the redistribution of eroded soils and sediments within it. The dry sclerophyll study area was divided into several distinct elements: log landings, snig tacks, general harvest area (GHA), cross banks, and the filter strip of native vegetation left adjacent to the major streamline Measurements of two radionuclide tracers ( 137 Cs and 210 Pb-excess) in each of these locations were then integrated into budgets describing the movement of soil within and between the various landscape elements. The 137 Cs budget showed that no net loss of soil material had occurred from within the study area, with retention of 109 ± 14 %. Conversely, the 210 Pb-excess budget showed a total retention of 78 ± 12 %. The deficit of 2 10 Pb compared to that of 137 Cs was explained by a combination of analytical and sampling uncertainties, losses of 2 10 Pb associated with combustion and/or transport of litter and organic matter from the site, and some small loss of surface soil (to a depth of 2 mm). However, no evidence of surface-derived topsoil material was found in sediments currently being transported from the site. Both tracer budgets showed that a net loss of soil from the snig tracks and log landings had occurred. This was quantified to be 28 ± 13 mm and 48 ± 29 mm depth from these land forms respectively. Up to 30 % of this loss could be directly attributable to the creation of the cross banks by bulldozer blading. The remainder was associated with mechanical losses due to export on truck tyres and bark, dust during the dry summer harvesting phase, and losses associated with sheet and rill erosion during storm events over the intervening years. Soil material eroded from the log landings was

  14. Water and Sediment Output Evaluation Using Cellular Automata on Alpine Catchment: Soana, Italy - Test Case

    Science.gov (United States)

    Pasculli, Antonio; Audisio, Chiara; Sciarra, Nicola

    2017-12-01

    In the alpine contest, the estimation of the rainfall (inflow) and the discharge (outflow) data are very important in order to, at least, analyse historical time series at catchment scale; determine the hydrological maximum and minimum estimate flood and drought frequency. Hydrological researches become a precious source of information for various human activities, in particular for land use management and planning. Many rainfall- runoff models have been proposed to reflect steady, gradually-varied flow condition inside a catchment. In these last years, the application of Reduced Complexity Models (RCM) has been representing an excellent alternative resource for evaluating the hydrological response of catchments, within a period of time up to decades. Hence, this paper is aimed at the discussion of the application of the research code CAESAR, based on cellular automaton (CA) approach, in order to evaluate the water and the sediment outputs from an alpine catchment (Soana, Italy), selected as test case. The comparison between the predicted numerical results, developed through parametric analysis, and the available measured data are discussed. Finally, the analysis of a numerical estimate of the sediment budget over ten years is presented. The necessity of a fast, but reliable numerical support when the measured data are not so easily accessible, as in Alpine catchments, is highlighted.

  15. National Uranium Resource Evaluation Program: the Hydrogeochemical Stream Sediment Reconnaissance Program at LLNL

    International Nuclear Information System (INIS)

    Higgins, G.H.

    1980-08-01

    From early 1975 to mid 1979, Lawrence Livermore National Laboratory (LLNL) participated in the Hydrogeochemical Stream Sediment Reconnaissance (HSSR), part of the National Uranium Resource Evaluation (NURE) program sponsored by the Department of Energy (DOE). The Laboratory was initially responsible for collecting, analyzing, and evaluating sediment and water samples from approximately 200,000 sites in seven western states. Eventually, however, the NURE program redefined its sampling priorities, objectives, schedules, and budgets, with the increasingly obvious result that LLNL objectives and methodologies were not compatible with those of the NURE program office, and the LLNL geochemical studies were not relevant to the program goal. The LLNL portion of the HSSR program was consequently terminated, and all work was suspended by June 1979. Of the 38,000 sites sampled, 30,000 were analyzed by instrumental neutron activation analyses (INAA), delayed neutron counting (DNC), optical emission spectroscopy (OES), and automated chloride-sulfate analyses (SC). Data from about 13,000 sites have been formally reported. From each site, analyses were published of about 30 of the 60 elements observed. Uranium mineralization has been identified at several places which were previously not recognized as potential uranium source areas, and a number of other geochemical anomalies were discovered

  16. Modeling sediment yield in small catchments at event scale: Model comparison, development and evaluation

    Science.gov (United States)

    Tan, Z.; Leung, L. R.; Li, H. Y.; Tesfa, T. K.

    2017-12-01

    Sediment yield (SY) has significant impacts on river biogeochemistry and aquatic ecosystems but it is rarely represented in Earth System Models (ESMs). Existing SY models focus on estimating SY from large river basins or individual catchments so it is not clear how well they simulate SY in ESMs at larger spatial scales and globally. In this study, we compare the strengths and weaknesses of eight well-known SY models in simulating annual mean SY at about 400 small catchments ranging in size from 0.22 to 200 km2 in the US, Canada and Puerto Rico. In addition, we also investigate the performance of these models in simulating event-scale SY at six catchments in the US using high-quality hydrological inputs. The model comparison shows that none of the models can reproduce the SY at large spatial scales but the Morgan model performs the better than others despite its simplicity. In all model simulations, large underestimates occur in catchments with very high SY. A possible pathway to reduce the discrepancies is to incorporate sediment detachment by landsliding, which is currently not included in the models being evaluated. We propose a new SY model that is based on the Morgan model but including a landsliding soil detachment scheme that is being developed. Along with the results of the model comparison and evaluation, preliminary findings from the revised Morgan model will be presented.

  17. Characterization and evaluation of potential reuse options for wastewater sludge and combined sewer system sediments in Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez, B.; Mendez, J.M.; Barrios, J.A.; Salgado, G.; Sheinbaum, C.

    2003-07-01

    Combined sewer systems generate sediments that have characteristics similar to those of primary sludge. Mexico City has such a system composed of a network of pipes, regulation structures (dams, basins) and open channels. The annual generation of sediments is estimated in 2.8 Mm{sup 3}, which includes 0.41 Mm{sup 3} of sludge. As a result, the total capacity for transporting water is reduced considerably, making necessary to extract yearly an approximate 0.85 Mm{sup 3} of those materials and to send them to a final disposal site with a capacity that is being exhausted. As part of the local Governmental effort, this project evaluates the quality of sediments from 6 dams, 4 regulation basins, 2 open channels, and 3 transfer stations. Also, sludge from 20 wastewater treatment plants was sampled. The results showed an important presence of lead and hydrocarbons in some sediments, and some sludge samples contained arsenic and nickel above the limits. Moreover, microbial levels exceeded the limits in all the sediments and sludge samples. Erosion was linked to the generation of an important amount of sediments based on lead concentration. A classification was established to determine the degree of contamination of the sediments as well as the required treatment to allow their potential reuse. (author)

  18. Modern pollen and stomate deposition in lake surface sediments from across the treeline on the Kola Peninsula, Russia.

    Science.gov (United States)

    Gervais, B R.; MacDonald, G M.

    2001-04-01

    We sampled and analyzed surface sediments from 31 lakes along a latitudinal transect crossing the coniferous treeline on the Kola Peninsula, Russia. The major vegetation zones along the transect were tundra, birch-forest tundra, pine-forest tundra, and forest. The results indicate that the major vegetation types in our study area have distinct pollen spectra. Sum-of-squares cluster analysis and principal components analysis (PCA) groupings of pollen sites correspond to the major vegetation zones. PCA ordination of taxa indicates that the first axis separates taxa typical of the forest zone (Pinus, Picea) from taxa typical of tundra and forest-tundra zones (Polypodiaceae, Ericaceae, and Betula). The current position of the coniferous treeline, defined in our region by Pinus sylvestris, occurs roughly where Pinus pollen values reach 35% or greater. Arboreal pollen (AP)/non-arboreal pollen (NAP) ratios were calculated for each site and plotted against geographic distance along the transect. AP/NAP ratios of 7 or greater are found within pine-forest tundra and forest vegetation zones. Pinus stomates (dispersed stomatal guard cells) are absent from sites north of the coniferous treeline and all but two samples from the forested sites contain stomates. Stomate concentrations among the samples are highly variable and range from 10 to 458 per ml and positively correlate with the changing Pinus pollen values.

  19. EVALUATION OF BIOAEROSOL COMPONENTS, GENERATION FACTORS, AND AIRBORNE TRANSPORT ASSOCIATED WITH LIME TREATMENT OF CONTAMINATED SEDIMENT

    Science.gov (United States)

    Lime treatment has been used in contaminated sediment management activities for many purposes such as dewatering, improvement of physical properties, and reducing contaminant mobility. Exothermic volatilization of volatile organic compounds from lime-treated sediment is well kno...

  20. Geomorphological condition and sea bottom sediment characteristics of Sebagin coast for NPP site evaluation in South Bangka

    International Nuclear Information System (INIS)

    Yuliastuti; Heni Susiati; Yarianto Sugeng Budi Susilo

    2015-01-01

    Study on geomorphological condition and sea bottom sediment in the coastal area of Sebagin, South Bangka Regency, Bangka Belitung Province has been performed. Geomorphological of the seabed was valuable to identify geological structures that exist on the seabed layers. Whereas, sediments seabed characteristics was useful to provide portrait of seabed layer due to the stability of NPP site concerning the seismic aspect and the determination of water intake position. The objective of the study was to evaluate geomorphological condition and sea bed sediment characteristics in the South Bangka sea. Methodology used for evaluating geomorphological of the sea bed were Multi Beam Echo Sounder (MBES) and Single Beam Echo Sounder (SBES), while for sea bottom sediment characteristics, high resolution seismic reflection using SBP together with sediment sample analysis were used. The result of the study showed that the study area was a shallow water sea with a depth range of 1-59 m. Geomorphological profile of the sea bed tend to be irregular and based on the seismic interpretation, there were no fault exists. Result analysis on the sea bottom sediment showed that clay distribution dominated the study area. (author)

  1. Conditions of uranium-bearing calcite formation in ore-enclosing sediments of the Semizbaj deposit (Kazakhstan)

    International Nuclear Information System (INIS)

    Kondrat'eva, I.A.; Maksimova, I.G.; Dojnikova, O.I.

    1995-01-01

    Consideration is given to results of investigation into uranium-bearing calcite, forming the cement of gravelly-sandy rocks of the Semizbaj uranium deposit. Core sampling in prospecting boreholes were used to establish geological conditions, place and time of uranium-bearing calcite formation. Calcite was investigated by optical, electron-microscope and radiographic methods. It is shown that uranium in calcite doesn't form its own mineral phase and exists in scattered state. Uranium in calcite-bearing minerals is present in isomorphic form. Uranium content in calcite was equal to 0.009-0.15 %. It is proposed that mineralization, formed in sedimentary rocks by processes of ground-stratum oxidation, is the source of uranium, enriching calcite. refs., 5 figs., 2 tabs

  2. SEDIMENTATION AND DEPOSITIONAL ENVIRONMENT BASED ON SEISMIC AND DRILLING CORE ANALYSES IN CIMANUK DELTA INDRAMAYU, WEST JAVA

    Directory of Open Access Journals (Sweden)

    I Nyoman Astawa

    2017-07-01

    Full Text Available Core drilling had been carried out in three locations such as in Brondong Village (BH-01, Pasekan Village (BH-02, and Karangsong Village (BH-03. Those three cores are similar in lithology consist of clay. They are correlated based on fragment content, such as fine sand lenses, mollusk shells, rock and carbonate materials which discovered from different depths. Single side band of shallow seismic reflection recorded paleochannels in E sequence at the north and the west of investigated area. It’s predicted the north paleo channels were part of Lawas River or Tegar River, while the west paleo channels were part of Rambatan Lama River. Microfauna content of all those three cores indicated that from the depth of 0.00 meter down to 25,00 meters are Holocene/Recent, from 25,00 meters to the bottom are Pleistocene which were deposited in the bay to middle neritic environment.

  3. Evaluation of the various biokinetic models of liberation from characteristic deposition fraction of brazilian population sample

    International Nuclear Information System (INIS)

    Reis, Arlene A. dos; Cardoso, Joaquim C.S.; Lourenco, Maria Cristina

    2005-01-01

    The Publication 66 of International Commission of Radiological Protection (ICRP, 1994) presented the Human Respiratory tract Model that simulates the deposition and translocation of radioactive material in the air that penetrates in the body by inhalation. The main objective of this study is to evaluate the variation in fractional activity absorbed into blood when physiological and morphological parameters from Brazilian population are applied in the deposition model. The clearance model was implemented in the software Excel (version 2000) using a system of differential equations to solve simultaneous process of translocation and absorption of material deposited. After implementation were applied in the model fractional deposition calculated by deposition model using physiological and morphological parameters from Brazilian population. The results show that the variation in the clearance model depends on the material dissolution. For materials of rapid absorption, the variations calculated are not significant. Materials of moderate and slow absorption, presented variation greater than 20% in fractional activity absorbed into blood, depending on levels of exercise. (author)

  4. Evaluating the Contributions of Atmospheric Deposition of Carbon and Other Nutrients to Nitrification in Alpine Environments

    Science.gov (United States)

    Oldani, K. M.; Mladenov, N.; Williams, M. W.

    2013-12-01

    The Colorado Front Range of the Rocky Mountains contains undeveloped, barren soils, yet in this environment there is strong evidence for a microbial role in increased nitrogen (N) export. Barren soils in alpine environments are severely carbon-limited, which is the main energy source for microbial activity and sustenance of life. It has been shown that atmospheric deposition can contain high amounts of organic carbon (C). Atmospheric pollutants, dust events, and biological aerosols, such as bacteria, may be important contributors to the atmospheric organic C load. In this stage of the research we evaluated seasonal trends in the chemical composition and optical spectroscopic (fluorescence and UV-vis absorbance) signatures of snow, wet deposition, and dry deposition in an alpine environment at Niwot Ridge in the Rocky Mountains of Colorado to obtain a better understanding of the sources and chemical character of atmospheric deposition. Our results reveal a positive trend between dissolved organic carbon concentrations and calcium, nitrate and sulfate concentrations in wet and dry deposition, which may be derived from such sources as dust and urban air pollution. We also observed the presence of seasonally-variable fluorescent components that may be attributed to fluorescent pigments in bacteria. These results are relevant because atmospheric inputs of carbon and other nutrients may influence nitrification in barren, alpine soils and, ultimately, the export of nitrate to alpine watersheds.

  5. Evaluation methods for assessing effectiveness of in situ remediation of soil and sediment contaminated with organic pollutants and heavy metals.

    Science.gov (United States)

    Song, Biao; Zeng, Guangming; Gong, Jilai; Liang, Jie; Xu, Piao; Liu, Zhifeng; Zhang, Yi; Zhang, Chen; Cheng, Min; Liu, Yang; Ye, Shujing; Yi, Huan; Ren, Xiaoya

    2017-08-01

    Soil and sediment contamination has become a critical issue worldwide due to its great harm to the ecological environment and public health. In recent years, many remediation technologies including physical, chemical, biological, and combined methods have been proposed and adopted for the purpose of solving the problems of soil and sediment contamination. However, current research on evaluation methods for assessing these remediation technologies is scattered and lacks valid and integrated evaluation methods for assessing the remediation effectiveness. This paper provides a comprehensive review with an environmental perspective on the evaluation methods for assessing the effectiveness of in situ remediation of soil and sediment contaminated with organic pollutants and heavy metals. The review systematically summarizes recent exploration and attempts of the remediation effectiveness assessment based on the content of pollutants, soil and sediment characteristics, and ecological risks. Moreover, limitations and future research needs of the practical assessment are discussed. These limitations are not conducive to the implementation of the abatement and control programs for soil and sediment contamination. Therefore, more attention should be paid to the evaluation methods for assessing the remediation effectiveness while developing new in situ remediation technologies in future research. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Evaluation of sediment management strategies on reservoir storage depletion rate: a case study

    NARCIS (Netherlands)

    Ali, M.; Sterk, G.

    2010-01-01

    Sedimentation aspects have a major role during the design of new reservoir projects because life of the reservoir mainly depends upon sediment handling during reservoir operation. Therefore, proper sediment management strategies should be adopted to enhance the life span of reservoirs. Basha

  7. Overview of the National Uranium Resource Evaluation Hydrogeochemical and Stream Sediment Reconnaissance Program

    International Nuclear Information System (INIS)

    Bolivar, S.L.

    1980-01-01

    A Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) for uranium is currently being conducted throughout the conterminous United States and Alaska. The HSSR is part of the National Uranium Resource Evaluation sponsored by the US Department of Energy. This ambitious geochemical reconnaissance program is conducted by four Department of Energy laboratories: Los Alamos Scientific Laboratory, Lawrence Livermore Laboratory, Oak Ridge Gaseous Diffusion Plant, and Savannah River Laboratory. The program is based on an extensive review of world literature, reconnaissance work done in other countries, and pilot studies conducted by each laboratory. Sample-collection methods and sample density are determined to optimize the probability of detecting potential uranium mineralization. To achieve this aim, each laboratory has developed independent standardized field collection procedures that are designed for its section of the country. Field parameters such as pH, conductivity, climate, geography, and geology are recorded at each site. Most areas are sampled at densities of one sample site per 10 to 23 km 2 . The HSSR program has helped to improve existing hydrogeochemical reconnaissance exploration techniques. In addition to providing industry with data that may help to identify potential uranium districts and to extend known uranium provinces, the HSSR also provides multielement analytical data that can be used in water quality, soil, sediment, environmental, and base-metal exploration studies

  8. Overview of the National Uranium Resource Evaluation Hydrogeochemical and Stream Sediment Reconnaissance Program

    International Nuclear Information System (INIS)

    Bolivar, S.L.

    1980-07-01

    A Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) for uranium is currently being conducted throughout the conterminous United States and Alaska. The HSSR is part of the National Uranium Resource Evaluation sponsored by the US Department of Energy. This ambitious geochemical reconnasissance program is conducted by four Department of Energy Laboratories: Los Alamos Scientific Laboratory, Lawrence Livermore Laboratory, Oak Ridge Gaseous Diffusion Plant, and Savannah River Laboratory. Each laboratory was assigned a geographic region of the United States. The program is based on an extensive review of world literature, reconnaissance work done in other countries, and pilot studies conducted by each laboratory. Sample-collection methods and sample density are determined to optimize the probability of detecting potential uranium mineralization. To achieve this aim, each laboratory has developed independent standardized field collection procedures that are designed for its section of the country. Field parameters such as pH, conductivity, climate, geography, and geology are recorded at each site. Most areas are sampled at densities of one sample site per 10 to 23 km 2 . The HSSR program has helped to improve existing hydrogeochemical reconnaissance exploration techniques. In addition to providing industry with data that may help to identify potential uranium districts and to extend known uranium provinces, the HSSR also provides multielement analytical data that can be used in water quality, soil, sediment, environmental, and base-metal exploration studies

  9. Preliminary evaluation of heavy metal contamination in the Zarrin-Gol River sediments, Iran.

    Science.gov (United States)

    Malvandi, Hassan

    2017-04-15

    The major objectives of the study were to test the hypothesis of the Zarrin-Gol River as a reference site for ecotoxicological studies and to assess the contamination degree of heavy metals and metalloids in the river using four contamination indices. For these purposes, eleven heavy metal and metalloid concentrations were analyzed. The average concentrations (mgkg -1 ) in the sediments were: 37.67 (chromium) 286.28 (manganese), 13,751.04 (iron), 8.79 (cobalt), 12.39 (nickel), 32.68 (zinc), 21.91 (arsenic), 40.59 (selenium), 2923.86 (aluminum), ND (silver) and 785.96 (magnesium). Contamination factor, enrichment factor, pollution load index, and geoaccumulation index were calculated to evaluate the contamination degree and influence of human activities on heavy metal levels. The contamination indices of the sediment samples showed that arsenic and selenium were the highest pollutants. The results indicated that the Zarrin-Gol River could not be used as a reference site at least for arsenic and selenium. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. State-of-the-art for evaluating the potential effects of erosion and deposition on a radioactive waste repository. Final report

    International Nuclear Information System (INIS)

    1980-01-01

    The potential impact of future geologic processes on the integrity of a deep, high-level radioactive-waste repository is evaluated. The following study identifies the potential consequences of surface erosion and deposition on sub-surface repository containment characteristics and assesses the ability to measure and predict quantitatively the rates and corresponding extent of these processes in the long term. Numerous studies of the magnitudes and rates of surficial erosion and deposition that have been used to determine the minimum allowable depth for a geologic repository (300 m - NRC Code of Federal Regulations, Part 60.122, Draft 10) are cited in this report. Measurement and interpretation of potential rates and extent of surficial processes in these studies involved considerable uncertainty, and the implications of this uncertainty on presently proposed repository siting criteria are addressed herein. Important concepts that should be considered when developing siting criteria to protect against deleterious effects arising from future erosion or deposition are highlighted. Erosion agents that could affect deep repositories are distinguished in this report so that their individual and combined impacts may be examined. This approach is recommended when evaluating potential repository sites in diverse environments that are susceptible to different agents of erosion. In contrast, agents of sedimentation are not differentiated in this report because of their relatively minor impact on a deep repository

  11. Preliminary evaluation of uranium deposits. A geostatistical study of drilling density in Wyoming solution fronts

    International Nuclear Information System (INIS)

    Sandefur, R.L.; Grant, D.C.

    1976-01-01

    Studies of a roll-front uranium deposit in Shirley Basin Wyoming indicate that preliminary evaluation of the reserve potential of an ore body is possible with less drilling than currently practiced in industry. Estimating ore reserves from sparse drilling is difficult because most reserve calculation techniques do not give the accuracy of the estimate. A study of several deposits with a variety of drilling densities shows that geostatistics consistently provides a method of assessing the accuracy of an ore reserve estimate. Geostatistics provides the geologist with an additional descriptive technique - one which is valuable in the economic assessment of a uranium deposit. Closely spaced drilling on past properties provides both geological and geometric insight into the occurrence of uranium in roll-front type deposits. Just as the geological insight assists in locating new ore bodies and siting preferential drill locations, the geometric insight can be applied mathematically to evaluate the accuracy of a new ore reserve estimate. By expressing the geometry in numerical terms, geostatistics extracts important geological characteristics and uses this information to aid in describing the unknown characteristics of a property. (author)

  12. Evaluation of the effects of coal fly ash amendments on the toxicity of a contaminated marine sediment

    Energy Technology Data Exchange (ETDEWEB)

    Burgess, R.M.; Perron, M.M.; Friedman, C.L.; Suuberg, E.M.; Pennell, K.G.; Cantwell, M.G.; Pelletier, M.C.; Ho, K.T.; Serbst, J.R.; Ryba, S.A. [US EPA, Narragansett, RI (USA). Office for Research and Development

    2009-01-15

    Approaches for cleaning up contaminated sediments range from dredging to in situ treatment. In this study, we discuss the effects of amending reference and contaminated sediments with coal fly ash to reduce the bioavailability and toxicity of a field sediment contaminated with polycyclic aromatic hydrocarbons (PAHs). Six fly ashes and a coconut charcoal were evaluated in 7-d whole sediment toxicity tests with a marine amphipod (Ampelisca abdita) and mysid (Americamysis bahia). Fly ashes with high carbon content and the coconut charcoal showed proficiency at reducing toxicity. Some of the fly ashes demonstrated toxicity in the reference treatments. It is suspected that some of this toxicity is related to the presence of ammonia associated with fly ashes as a result of postoxidation treatment to reduce nitrous oxide emissions. Relatively simple methods exist to remove ammonia from fly ash before use, and fly ashes with low ammonia content are available. Fly ashes were also shown to effectively reduce overlying water concentrations of several PAHs. No evidence was seen of the release of the metals cadmium, copper, nickel, or lead from the fly ashes. A preliminary 28-d polychaete bioaccumulation study with one of the high-carbon fly ashes and a reference sediment was also performed. Although preliminary, no evidence was seen of adverse effects to worm growth or lipid content or of accumulation of PAHs or mercury from exposure to the fly ash. These data show fly ashes with high carbon content could represent viable remedial materials for reducing the bioavailability of organic contaminants in sediments.

  13. Metallographic techniques for evaluation of Thermal Barrier Coatings produced by Electron Beam Physical Vapor Deposition

    International Nuclear Information System (INIS)

    Kelly, Matthew; Singh, Jogender; Todd, Judith; Copley, Steven; Wolfe, Douglas

    2008-01-01

    Thermal Barrier Coatings (TBC) produced by Electron Beam Physical Vapor Deposition (EB-PVD) are primarily applied to critical hot section turbine components. EB-PVD TBC for turbine applications exhibit a complicated structure of porous ceramic columns separated by voids that offers mechanical compliance. Currently there are no standard evaluation methods for evaluating EB-PVD TBC structure quantitatively. This paper proposes a metallographic method for preparing samples and evaluating techniques to quantitatively measure structure. TBC samples were produced and evaluated with the proposed metallographic technique and digital image analysis for columnar grain size and relative intercolumnar porosity. Incorporation of the proposed evaluation technique will increase knowledge of the relation between processing parameters and material properties by incorporating a structural link. Application of this evaluation method will directly benefit areas of quality control, microstructural model development, and reduced development time for process scaling

  14. Geochemical Evaluation of black shales from the deposit Nizna Slana, lower paleozoic, Western Carpatians

    International Nuclear Information System (INIS)

    Turanova, L.; Turan, J.; Khun, M.

    1996-01-01

    Black shales from the deposit Nizna Slana and its immediate surroundings can be divided into black shales ss, carbonate black shales and siliceous black shales on the basis of chemical composition. Basic statistical characteristics of main and trace elements, as well as content of organic carbon, are evaluated and compared in this paper, either numerically, or graphically using the box-and whisker diagrams (median, 25 % percentile, 75 % percentile, total extent). (authors)

  15. The interaction between land use change, sediment fluxes and carbon dynamics: evaluating an integrated soil-landscape model at the millennial time-scale.

    Science.gov (United States)

    Bouchoms, Samuel; Van Oost, Kristof; Vanacker, Veerle

    2015-04-01

    Soil-landscape modelling has received growing attention as it allows us to evaluate the interaction between earth surface and soil bio-physical processes. At the landscape scale, human-induced land use change has altered the balance between soil erosion and production, and largely modified sediment fluxes. Intensification in soil redistribution rates affects the interaction between soil chemical, physical and biological processes at the landscape scale. Here, we evaluate the SPEROS-LT model, a spatially explicit 3D model combining a dynamic representation of land use, soil erosion and deposition and the soil carbon cycle. We assess the impact of millennial-scale human-induced land use change on sediment fluxes and carbon dynamics in the Dijle catchement (central Belgium). The watershed has undergone a 3000 years continuous human-induced alteration of the vegetation covers for agricultural characterized by Our study is based on land use reconstructions for the last 3000 years, including massive deforestation for agriculture in Roman Times and the Middle Ages followed by urbanization in the last 150 years. Land use reconstructions rely on simple land use allocation rules based on slope gradients. SPEROS-LT is parametrized for erosion rates against available figures in the literature by changing the transport capacity and the transfer coefficient which defines the amount of flux transferred between different land uses. Carbon content profiles at steady state (i.e. without influence of erosion or deposition) are calibrated for each land use and for the first upper meter of soil by comparing modeled profiles to an averaged observed profiles in stable areas of the pedologic region. We present a model sensitivity analysis and a full validation of the predicted soil carbon storage (horizontally, i.e. in space, and vertically, i.e. with depth) using a large database of observational data. The results indicate (i) a good agreement of the erosion rates. Speros LT modeled

  16. Evaluation of variables which affect the hardness of nickel plate deposited from watts-type baths

    International Nuclear Information System (INIS)

    Petit, G.S.; Wright, R.R.; Neff, W.A.

    1976-01-01

    In the course of the Cascade Improvement Program, many component equipment parts will be electroplated with nickel for corrosion protection. The maximum hardness which will be acceptable in the electroplated deposit is specified in Union Carbide's Job Specification JS-1396, Revision 3, entitled Electroplated Nickel Coatings on Steel Parts. The hardness specification is intended primarily as a control over both organic and inorganic impurities in the deposit. This report covers a study evaluating several of the numerous controllable variables which influence the hardness of the nickel plate deposited from a Watts-type bath. The variables tested were: 1) bath composition, 2) pH, 3) current density, 4) anode-cathode area ratio, and 5) bath temperature. Within the tested ranges of the variables studied, the pH and current density had the most influence on the plate hardness. The softest deposit was obtained with a bath pH of 1.5, a current density of 30 to 40 amperes/square foot, and with the anode-cathode area ratio in the range of 3:1 to 1:1

  17. Depositional record of trace metals and degree of contamination in core sediments from the Mandovi estuarine mangrove ecosystem, west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Veerasingam, S.; Vethamony, P.; ManiMurali, R.; Fernandes, B.

    of sources. Enrichment of metals in bottom sediments represents a critical measure of health for any mangrove ecosystem (Janaki-Raman et al., 2007). Trace metals in coastal and estuarine sediments are incorporated into the aquatic food webs through primary... of susceptibility of the particles to the processes of physical and chemical weathering. The different morphological forms of iron oxides are well correlated with the sediment horizons. Spherical iron oxides predominate in the upper layers of sediment profiles...

  18. Evaluation of ash deposits during experimental investigation of co-firing of Bosnian coal with wooden biomass

    Energy Technology Data Exchange (ETDEWEB)

    Smajevic, Izet; Kazagic, Anes [JP Elektroprivreda BiH d.d., Sarajevo (Bosnia and Herzegovina); Sarajevo Univ. (Bosnia and Herzegovina). Faculty of Mechanical Engineering

    2008-07-01

    The paper is addressed to the development and use different criteria for evaluation of ash deposits collected during experimental co-firing of Bosnian coals with wooden biomass. Spruce saw dust was used for the co-firing tests with the Kakanj brown coal and with a lignite blend consisted of the Dubrave lignite and the Sikulje lignite. The coal/biomass mixtures at 93:7 %w and at 80:20 %w were tested. Experimental lab-scale facility PF entrained flow reactor is used for the co-firing tests. The reactor allows examination of fouling/slagging behaviors and emissions at various and infinitely variable process temperature which can be set at will in the range from ambient to 1560 C. Ash deposits are collected on two non-cooled ceramic probes and one water-cooled metal surface. Six different criteria are developed and used to evaluate behavior of the ash deposits on the probes: ash deposit shape, state and structure, which are analyzed visually - photographically and optically by a microscope, rate of adhesion and ash deposit strength, analyzed by physic acting to the ash deposits, and finally deposition rate, determined as a mass of the deposit divided by the collecting area and the time of collecting. Furthermore, chemical composition analysis and AFT of the ash deposits were also done to provide additional information on the deposits. (orig.)

  19. USE OF POWDERED COCONUT CHARCOAL AS A TOXICITY IDENTIFICATION AND EVALUATION MANIPULATION FOR ORGANIC TOXICANTS IN MARINE SEDIMENTS

    Science.gov (United States)

    We report on a procedure using powdered coconut charcoal to sequester organic contaminants and reduce toxicity in sediments as part of a series of toxicity identification and evaluation (TIE) methods. Powdered coconut charcoal (PCC) was effective in reducing the toxicity of endos...

  20. A kinetic approach to evaluate the association of acid volatile sulfide and simultaneously extracted metals in aquatic sediments

    NARCIS (Netherlands)

    Poot, A.; Meerman, E.; Gillissen, F.; Koelmans, A.A.

    2009-01-01

    The acid volatile sulfide (AVS) and simultaneously extracted metals (¿SEM) method is widely used for evaluating potential bioavailability of heavy metals in soil and sediment. It is also criticized, because the requirement that AVS and SEM metals (i.e., Cd, Cu, Ni, Pb, and Zn) are associated in the

  1. The impact of a tributary that carries high amounts of bed-load on the deposition of sediment downstream of a run-of river plant; Die Auswirkungen eines Geschiebe fuehrenden Zubringers auf die Verlandungssituation im Unterwasser eines Laufkraftwerkes

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, Josef; Sindelar, Christine; Feldbacher, Rupert; Knoblauch, Helmut [TU Graz (Austria). Inst. fuer Wasserbau und Wasserwirtschaft

    2011-07-01

    For guaranteeing a sustainable sediment management on a chain of run-of river plants in the Salzach valley in Austria nearly annual flushings have been performed. The sediments that are removed out of the reservoirs tend to deposit immediately downstream of the dams mainly at the outlet of the turbines due to widening or reduced slope. During the physical model tests, which were performed for the hydro power plant St. Veit, it could be observed that the boundary conditions were obviously wrong because in the prototype much more sediment was settled as in the model. A downstream located tributary was found responsible because of its dumping of high amounts of bed load into the river Salzach. This led to a backwater flow respectively reduced shear stresses. Further model tests resulted in a successful solution which mitigates the situation substantially. (orig.)

  2. Underground geologic evaluation of the Grossschloppen vein-uranium deposit, West Germany

    International Nuclear Information System (INIS)

    Moore, S.C.; Erickson, A.J.; Kolb, S.G.; Maclean, C.J.

    1983-01-01

    The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Er/ZETA/ GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gamma probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 m thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling

  3. Evaluation of target power supplies for krypton storage in sputter-deposited metals

    International Nuclear Information System (INIS)

    Greenwell, E.N.; McClanahan, E.D.; Moss, R.W.

    1986-04-01

    Implantation of 85 Kr in a growing sputtered metal deposit has been studied for the containment of 85 Kr recovered from the reprocessing of spent nuclear fuel. PNL, as part of DOE's research program for 85 Kr storage, has developed krypton trapping storage devices (KTSDs) in a range of sizes for ''cold'' and radioactive testing. The KTSD is a stainless steel canister that contains a sputtering target for depositing an amorphous rare-earth transition metal on the inner wall and simultaneously implanting low-energy krypton ions in the growing deposit. This report covers the design requirements for the target power supply and the description, testing and evaluation of three basic designs. The designs chosen for evaluation were: (1) a standard commercial power supply with an external PNL-designed current interrupter, (2) a commercially manufactured power supply with an integral series-type interrupter, and (3) a commercially manufactured power supply with an integral shunt-type interrupter. The units were compared on the basis of performance, reliability, and life-cycle cost. 8 refs., 9 figs., 2 tabs

  4. Evaluation of human body irradiation caused by radionuclides deposited in the filtration unit of gas mask

    International Nuclear Information System (INIS)

    Cerny, R.; Otahal, P.; Johnova, K.; Thinova, L.; Kluson, J.

    2017-01-01

    Radioactive aerosol particles represent a serious risk for people facing the consequences of nuclear accident of any kind. The first responders to emergency situation need to be protected by personal protective equipment which includes radiation protection suit supplemented with gas mask. The purpose of this work is to estimate the dose to the organs of responder s body as a result of radionuclide deposition in the filtration unit of the gas mask. The problem was analyzed using Monte Carlo simulations. The dose absorbed by different organs for five representative radionuclides and the dose distribution over the responder s body are presented in this paper. Based on presented MC simulations, we suggest a method of evaluating the irradiation of the responder by the radionuclides deposited in the filtration unit of the gas mask. (authors)

  5. EXPURT - a model for evaluating exposure from radioactive material deposited in the urban environment

    International Nuclear Information System (INIS)

    Crick, M.J.; Brown, J.

    1990-06-01

    This model, EXPURT (EXPosure from Urban Radionuclide Transfer), is described in detail. The model simulates the movement of activity deposited on various surfaces in the urban environment and, by taking into account the shielding properties of buildings and the habits of the population, evaluates the external doses to members of the population living in such urban environments, as a function of time after deposition. One of the other advantages of EXPURT over simpler models is that it can be used to assess the possible dose reductions that might be achieved by various decontamination techniques; for example, it can estimate the effectiveness of decontaminating roof surfaces alone in reducing exposure to individuals living in an urban environment. Sensitivity/uncertainty studies have been performed whereby those parameters contributing most to remaining uncertainty in the model's predictions of dose and dose rates were identified. Predictions of the EXPURT model were compared with those from a simpler external dose model in use at NRPB. (author)

  6. Uranium accumulation in modern and ancient Fe-oxide sediments: Examples from the Ashadze-2 hydrothermal sulfide field (Mid-Atlantic Ridge) and Yubileynoe massive sulfide deposit (South Urals, Russia)

    Science.gov (United States)

    Ayupova, N. R.; Melekestseva, I. Yu.; Maslennikov, V. V.; Tseluyko, A. S.; Blinov, I. A.; Beltenev, V. E.

    2018-05-01

    Fe-oxyhydroxide sediments (gossans) from the Ashadze-2 hydrothermal sulfide field (Mid-Atlantic Ridge) and hematite-carbonate-quartz rocks (gossanites) from the Yubileynoe Cu-Zn VHMS deposit (South Urals) are characterized by anomalously high U contents (up to 352 ppm and 73 ppm, respectively). In gossans from the Ashadze-2 hydrothermal sulfide field, rare isometric anhedral uraninite grains (up to 2 μm) with outer P- and Ca-rich rims, and numerous smaller (<1 μm) grains, occur in Fe-oxyhydroxides and sepiolite, associated with pyrite, isocubanite, chalcopyrite, galena, atacamite and halite. In gossanites from the Yubileynoe deposit, numerous uraninite particles (<3 μm) are associated with apatite, V-rich Mg-chlorite, micro-nodules of pyrite, Se-bearing galena, hessite and acanthite in a hematite-carbonate-quartz matrix. Small (1-3 μm) round grains of uraninite, which locally coalesce to large grains up to 10 μm in size, are associated with authigenic chalcopyrite. The similar diagenetic processes of U accumulation in modern and ancient Fe-oxyhydroxide sediments were the result of U fixation from seawater during the oxidation of sulfide minerals. Uraninite in gossanites was mainly deposited from diagenetic pore fluids, which circulated in the sulfide-hyaloclast-carbonate sediments.

  7. Evaluation of trace elements distribution in water, sediment, soil and cassava plant in Muria peninsula environment by NAA method

    International Nuclear Information System (INIS)

    Muryono, H.; Sumining; Agus Taftazani; Kris Tri Basuki; Sukarman, A.

    1999-01-01

    The evaluation of trace elements distribution in water, sediment, soil and cassava plant in Muria peninsula by NAA method were done. The nuclear power plant (NPP) and the coal power plant (CPP) will be built in Muria peninsula, so, the Muria peninsula is an important site for samples collection and monitoring of environment. River-water, sediment, dryland-soil and cassava plant were choosen as specimens samples from Muria peninsula environment. The analysis result of trace elements were used as a contributed data for environment monitoring before and after NPP was built. The trace elements in specimens of river-water, sediment, dryland-soil and cassava plant samples were analyzed by INAA method. It was found that the trace elements distribution were not evenly distributed. Percentage of trace elements distribution in river-water, sediment, dryland-soil and cassava leaves were 0.00026-0.037% in water samples, 0.49-62.7% in sediment samples, 36.29-99.35% in soil samples and 0.21-99.35% in cassava leaves. (author)

  8. Evaluation of trace elements distribution in water, sediment, soil and cassava plant in Muria peninsula environment by NAA method

    Energy Technology Data Exchange (ETDEWEB)

    Muryono, H.; Sumining; Agus Taftazani; Kris Tri Basuki; Sukarman, A. [Yogyakarta Nuclear Research Center, Yogyakarta (Indonesia)

    1999-10-01

    The evaluation of trace elements distribution in water, sediment, soil and cassava plant in Muria peninsula by NAA method were done. The nuclear power plant (NPP) and the coal power plant (CPP) will be built in Muria peninsula, so, the Muria peninsula is an important site for samples collection and monitoring of environment. River-water, sediment, dryland-soil and cassava plant were choosen as specimens samples from Muria peninsula environment. The analysis result of trace elements were used as a contributed data for environment monitoring before and after NPP was built. The trace elements in specimens of river-water, sediment, dryland-soil and cassava plant samples were analyzed by INAA method. It was found that the trace elements distribution were not evenly distributed. Percentage of trace elements distribution in river-water, sediment, dryland-soil and cassava leaves were 0.00026-0.037% in water samples, 0.49-62.7% in sediment samples, 36.29-99.35% in soil samples and 0.21-99.35% in cassava leaves. (author)

  9. Sedimentation studies relevant to low-level radioactive effluent dispersal in the Irish Sea. Part III. An evaluation of possible mechanisms for the incorporation of radionuclides into marine sediments

    International Nuclear Information System (INIS)

    Kirby, R.; Parker, W.R.; Pentreath, R.J.; Lovett, M.B.

    1983-01-01

    Based on circumstantial evidence the Cumbrian mud area was previously interpreted as accretionary. There are no measurements confirming that riverborne sediment reaches the mud area and the postulated subtidal sources appear to be sealed by a lag gravel. In contrast, fine sediment deposited in Liverpool Bay is known to return to the Ribble, Mersey and Dee. Similarly 'hot' particles originating in the Sellafield outfall are implied to travel, perhaps accompanied by natural fine sediment, into the Ravenglass Estuary and elsewhere. The likely interpretation is that fine sediment accumulating in the coastal zone of the eastern Irish Sea is partly derived from seawards. Possible sources are coast erosion and the unconsolidated mud areas themselves. Radionuclide profiles from the Cumbrian mud area have previously been interpreted as confirming the accretionary hypothesis. In fact three principal types of radionuclide profiles occur, which are interpreted here to indicate progressively more efficient bioturbation. Burrowing animals may also supply uncontaminated sediment to the bed, where it absorbs radionuclides before, in part, being redeposited locally. This implies that no large external sediment source is necessary to explain the radionuclide profiles encountered. We thus interpret the area as a relatively stable sedimentary regime dominated by biological processes. (author)

  10. Resolving the false-negative issues of the nonpolar organic amendment in whole-sediment toxicity identification evaluations.

    Science.gov (United States)

    Mehler, W Tyler; Keough, Michael J; Pettigrove, Vincent

    2018-04-01

    Three common false-negative scenarios have been encountered with amendment addition in whole-sediment toxicity identification evaluations (TIEs): dilution of toxicity by amendment addition (i.e., not toxic enough), not enough amendment present to reduce toxicity (i.e., too toxic), and the amendment itself elicits a toxic response (i.e., secondary amendment effect). One such amendment in which all 3 types of false-negatives have been observed is with the nonpolar organic amendment (activated carbon or powdered coconut charcoal). The objective of the present study was to reduce the likelihood of encountering false-negatives with this amendment and to increase the value of the whole-sediment TIE bioassay. To do this, the present study evaluated the effects of various activated carbon additions to survival, growth, emergence, and mean development rate of Chironomus tepperi. Using this information, an alternative method for this amendment was developed which utilized a combination of multiple amendment addition ratios based on wet weight (1%, lower likelihood of the secondary amendment effect; 5%, higher reduction of contaminant) and nonconventional endpoints (emergence, mean development rate). This alternative method was then validated in the laboratory (using spiked sediments) and with contaminated field sediments. Using these multiple activated carbon ratios in combination with additional endpoints (namely, emergence) reduced the likelihood of all 3 types of false-negatives and provided a more sensitive evaluation of risk. Environ Toxicol Chem 2018;37:1219-1230. © 2017 SETAC. © 2017 SETAC.

  11. Evaluation of sediment sampling devices and methods used in the NKS/EKO-1 project

    Energy Technology Data Exchange (ETDEWEB)

    Ilus, E. [Finnish Centre for Radiation and Nuclear Safety (Finland)

    1996-10-01

    The radioactive fallout caused by nuclear weapons tests in the 1960s and the accident at the Chernobyl NPP in 1986 has created useful markers in the sediments of many Nordic waters. These have been successfully used not only in radioecological studies but also in limnological and marine research dealing with sedimentation processes and rates. To be able to study sedimentation and processes in sediments, it is essential to obtain reliable samples from sediments. False conclusions are an obvious risk if the studies are based on biased field samples. More strictly,, it is unreasonable to perform exacting and expensive analyses if the samples themselves are unreliable or of poor quality. The instruments best suited for quantitative sampling of soft-bottom sediments appear to be those based on the coring principle. Box corers can be reliably used for bulk sampling of coherent sediments and some silty and sandy sediments. Many factors speak in favour of large diameters/areas of the corer orifices. It is not possible, however, to increase the tube diameter without negative impact to the corer`s handiness and increasing difficulty in handling and slicing of the cores. Despite the large variety of sampling instruments and many sources of error involved in the use of different instruments, it is most important to know and account for the disadvantages and to work as carefully as possible towards minimizing errors and obtaining undisturbed, reliable samples. (EG).

  12. Evaluation of the potential for using Greenlandic marine sediments for brick production

    DEFF Research Database (Denmark)

    Belmonte, Louise Josefine; Bertelsen, Ida Maria Gieysztor

    2016-01-01

    Fine grained marine sediments from near the Greenlandic towns of Ilulissat, Kangerlussuaq and Sisimiut were assessed as raw materials for local production of building bricks. The assessment included both analysis of the sediment characteristics and physical properties of miniature test brick...

  13. Evaluation of sediment sampling devices and methods used in the NKS/EKO-1 project

    International Nuclear Information System (INIS)

    Ilus, E.

    1996-01-01

    The radioactive fallout caused by nuclear weapons tests in the 1960s and the accident at the Chernobyl NPP in 1986 has created useful markers in the sediments of many Nordic waters. These have been successfully used not only in radioecological studies but also in limnological and marine research dealing with sedimentation processes and rates. To be able to study sedimentation and processes in sediments, it is essential to obtain reliable samples from sediments. False conclusions are an obvious risk if the studies are based on biased field samples. More strictly,, it is unreasonable to perform exacting and expensive analyses if the samples themselves are unreliable or of poor quality. The instruments best suited for quantitative sampling of soft-bottom sediments appear to be those based on the coring principle. Box corers can be reliably used mainly for bulk sampling of coherent sediments and some silty and sandy sediments. Many factors speak in favour of relatively large diameters/areas of the corer orifices. It is not possible, however, to increase the tube diameter endlessly without negative impact to the corer's handiness and increasing difficulty in handling and slicing of the cores. Despite the large variety of sampling instruments and many sources of error involved in the use of different instruments, it is most important to know and account for the disadvantages and to work as carefully as possible towards minimizing errors and obtaining undisturbed, reliable samples. (EG)

  14. Calculation and evaluation of sediment effect concentrations for the amphipod Hyalella azteca and the midge Chironomus riparius

    Science.gov (United States)

    Ingersoll, Christopher G.; Haverland, Pamela S.; Brunson, Eric L.; Canfield, Timothy J.; Dwyer, F. James; Henke, Chris; Kemble, Nile E.; Mount, David R.; Fox, Richard G.

    1996-01-01

    Procedures are described for calculating and evaluating sediment effect concentrations (SECs) using laboratory data on the toxicity of contaminants associated with field-collected sediment to the amphipod Hyalella azteca and the midge Chironomus riparius. SECs are defined as the concentrations of individual contaminants in sediment below which toxicity is rarely observed and above which toxicity is frequently observed. The objective of the present study was to develop SECs to classify toxicity data for Great Lake sediment samples tested with Hyalella azteca and Chironomus riparius. This SEC database included samples from additional sites across the United States in order to make the database as robust as possible. Three types of SECs were calculated from these data: (1) Effect Range Low (ERL) and Effect Range Median (ERM), (2) Threshold Effect Level (TEL) and Probable Effect Level (PEL), and (3) No Effect Concentration (NEC). We were able to calculate SECs primarily for total metals, simultaneously extracted metals, polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs). The ranges of concentrations in sediment were too narrow in our database to adequately evaluate SECs for butyltins, methyl mercury, polychlorinated dioxins and furans, or chlorinated pesticides. About 60 to 80% of the sediment samples in the database are correctly classified as toxic or not toxic depending on type of SEC evaluated. ERMs and ERLs are generally as reliable as paired PELs and TELs at classifying both toxic and non-toxic samples in our database. Reliability of the SECs in terms of correctly classifying sediment samples is similar between ERMs and NECs; however, ERMs minimize Type I error (false positives) relative to ERLs and minimize Type II error (false negatives) relative to NECs. Correct classification of samples can be improved by using only the most reliable individual SECs for chemicals (i.e., those with a higher percentage of correct classification). SECs

  15. Evaluation of the salt deposition on the canister surface of concrete cask. Part 2. Measurement test of the salt concentration in air and salt deposition in the field

    International Nuclear Information System (INIS)

    Wataru, Masumi

    2012-01-01

    Concerning the storage facility of spent nuclear fuel using the concrete cask, there is an issue of stress corrosion cracking(SCC). The cooling air goes up along the canister surface in the concrete cask. To evaluate the initiation of SCC or rusting, it is important to verify the estimation method of the sea salt deposition on the metal canister surface transported by cooling air including sea salt particles. To measure the deposition rate, field tests were performed in Choushi test center. In the field test, it was found that the amount of sea salt deposition was very low because the density of the atmospheric sea salt concentration was very low compared with the laboratory test. Using relation between laboratory data and filed data, it is possible to evaluate the salt deposition rate on the canister surface. We also measured atmospheric sea salt concentration in Choushi test center to make the environment condition clear and compared the measurement data with the calculation data to verify the evaluation model. We are developing the automatic measuring device for atmospheric sea salt concentration. To check its performance, we are measuring atmospheric sea salt concentration in Yokosuka Area of CRIEPI and it was confirmed that the device works for one month automatically and fulfills its specifications. (author)

  16. Definition and classification of surficial uranium deposits

    International Nuclear Information System (INIS)

    Toens, P.D.; Hambleton-Jones, B.B.

    1984-01-01

    Uraniferous surficial deposits may be broadly defined as uraniferous sediments or soils, usually of Tertiary to Recent age, that have not been subjected to deep burial and may or may not have been cemented to some degree. Evaluation of the available literature shows that confusion has arisen as to the use of the term ''calcrete'' when describing fluviatile sediments that have been calcified to a greater or lesser degree. It is felt that a useful purpose would be served by proposing a classification system which may go some way towards a redefinition of the applicable terminology. Unfortunately the terms ''calcrete'' or ''valley calcrete'' have been used to define Tertiary to Recent sediments ranging from boulder beds to silts which, in some Namibian examples, contain between 5 and 50% CaCO 3 and as much as 90% total carbonate in some Australian surficial uranium deposits. It is proposed that the detrital material constituting the sediments be prefixed with the terms calcareous, dolomitic, gypsiferous, halitiferous or ferruginous (e.g. calcareous grit) rather than the terms calcrete, dolocrete, gypcrete, and ferricrete, all of which have genetic connotations. The latter group of terms are preferably used for the pedogenic uranium deposits only. This will have the effect of placing these deposits in categories of their own and not confusing the issue with the overprint of pedogenic calcrete or duricrustal deposits which may or may not be present. This view is not shared by some authorities notably Butt and Carlisle (see this volume). (author)

  17. Atomic layer deposition synthesis and evaluation of core–shell Pt-WC electrocatalysts

    International Nuclear Information System (INIS)

    Hsu, Irene J.; Chen, Jingguang G.; Jiang, Xiaoqiang; Willis, Brian G.

    2015-01-01

    Pt-WC core shell particles were produced using atomic layer deposition (ALD) to deposit Pt layers onto WC particle substrates. A range of Pt depositions were used to determine the growth mechanism for the Pt-WC powder system. TEM imaging and Cu stripping voltammetry found that Pt ALD growth on WC powder substrates was similar to that on WC thin films. However, excess free carbon was found to affect Pt ALD by blocking adsorption sites on WC. The Pt-WC samples were evaluated for the oxygen reduction reaction using a rotating disk electrode to obtain quantitative activity information. The mass and specific activities for the 30 and 50 ALD cycle samples were found to be comparable to a 10 wt. % Pt/C catalyst. However, higher overpotentials and lower limiting currents were observed with ALD Pt-WC compared to Pt/C catalysts, indicating that the oxygen reduction mechanism is not as efficient on Pt-WC as on bulk Pt. Additionally, these Pt-WC catalysts were used to demonstrate hydrogen evolution reaction activity and were found to perform as well as bulk Pt catalyst but with a fraction of the Pt loading, in agreement with the previous work on Pt-WC thin film catalysts

  18. Measurements of Bismuth (214Bi) in Indoor Air and Evaluation of Deposition Fraction

    International Nuclear Information System (INIS)

    Mohamed, A.; Ahmed, A.A.; Yuness, M.

    2010-01-01

    The activity size distribution of unattached as well as attached 214 Bi to aerosol particles was measured in indoor air of physics department at Minia University, Minia City, Egypt. The samples were collected using a wire screen diffusion battery technique and a low pressure Berner cascade impactor. The mean Activity Median Thermodynamic Diameter (AMTD) of unattached 214 Bi was determined to be 1.25 nm with a relative mean Geometric Standard Deviation (GSD) of 1.29. A mean unattached fraction (fun) of 0.08±0.05 was obtained. The average activity concentration of 214 Bi was found to be 4.9±0.42 Bq m -3 . Most of the attached activities of progeny were associated with aerosol particles of the accumulation mode. The GSD of the accumulation mode of 214 Bi was determined to be 3 with an Active Median Aerodynamic Diameter (AMAD) of 350 nm. Based on the obtained measured data values, deposition fraction of 214 Bi has been evaluated by using a stochastic deposition model. The bronchial deposition efficiencies of particles in the size range of attached 214 Bi were found to be lower than those of unattached progeny

  19. Development and Preliminary Evaluation of a Spray Deposition Sensing System for Improving Pesticide Application.

    Science.gov (United States)

    Kesterson, Melissa A; Luck, Joe D; Sama, Michael P

    2015-12-17

    An electronic, resistance-based sensor array and data acquisition system was developed to measure spray deposition from hydraulic nozzles. The sensor surface consisted of several parallel tin plated copper traces of varying widths with varying gap widths. The system contained an embedded microprocessor to monitor output voltage corresponding to spray deposition every second. In addition, a wireless module was used to transmit the voltage values to a remote laptop. Tests were conducted in two stages to evaluate the performance of the sensor array in an attempt to quantify the spray deposition. Initial tests utilized manual droplet placement on the sensor surface to determine the effects of temperature and droplet size on voltage output. Secondary testing utilized a spray chamber to pass nozzles at different speeds above the sensor surface to determine if output varied based on different application rates or spray droplet classification. Results from this preliminary analysis indicated that manual droplets of 5 and 10 μL resulted in significantly different values from the sensors while temperature did not consistently affect output. Spray chamber test results indicated that different application rates and droplet sizes could be determined using the sensor array.

  20. Fluidized bed deposition and evaluation of silicon carbide coatings on microspheres

    International Nuclear Information System (INIS)

    Federer, J.I.

    1977-01-01

    The fuel element for the HTGR is an array of closely packed fuel microspheres in a carbonaceous matrix. A coating of dense silicon carbide (SiC), along with pyrocarbon layers, is deposited on the fueled microspheres to serve as a barrier against diffusion of fission products. The microspheres are coated with silicon carbide in a fluidized bed by reaction of methyltrichlorosilane (CH 3 SiCl 3 or MTS) and hydrogen at elevated temperatures. The principal variables of coating temperature and reactant gas composition (H 2 /MTS ratio) have been correlated with coating rate, morphology, stoichiometry, microstructure, and density. The optimum temperature for depositing highly dense coatings is in the range 1475 to 1675 0 C. Lower temperatures result in silicon-rich deposits, while higher temperatures may cause unacceptable porosity. The optimum H 2 /MTS ratio for highly dense coatings is 20 or more (approximately 5% MTS or less). The amount of grown-in porosity increases as the H 2 /MTS ratio decreases below 20. The requirement that the H 2 /MTS ratio be about 20 or more imposes a practical restraint on coating rate, since increasing the total flow rate would eventually expel microspheres from the coating tube. Evaluation of stoichiometry, morphology, and microstructure support the above mentioned optimum conditions of temperature and reactant gas composition. 18 figures, 3 tables

  1. Evaluation and optimization of DNA extraction and purification procedures for soil and sediment samples.

    Science.gov (United States)

    Miller, D N; Bryant, J E; Madsen, E L; Ghiorse, W C

    1999-11-01

    We compared and statistically evaluated the effectiveness of nine DNA extraction procedures by using frozen and dried samples of two silt loam soils and a silt loam wetland sediment with different organic matter contents. The effects of different chemical extractants (sodium dodecyl sulfate [SDS], chloroform, phenol, Chelex 100, and guanadinium isothiocyanate), different physical disruption methods (bead mill homogenization and freeze-thaw lysis), and lysozyme digestion were evaluated based on the yield and molecular size of the recovered DNA. Pairwise comparisons of the nine extraction procedures revealed that bead mill homogenization with SDS combined with either chloroform or phenol optimized both the amount of DNA extracted and the molecular size of the DNA (maximum size, 16 to 20 kb). Neither lysozyme digestion before SDS treatment nor guanidine isothiocyanate treatment nor addition of Chelex 100 resin improved the DNA yields. Bead mill homogenization in a lysis mixture containing chloroform, SDS, NaCl, and phosphate-Tris buffer (pH 8) was found to be the best physical lysis technique when DNA yield and cell lysis efficiency were used as criteria. The bead mill homogenization conditions were also optimized for speed and duration with two different homogenizers. Recovery of high-molecular-weight DNA was greatest when we used lower speeds and shorter times (30 to 120 s). We evaluated four different DNA purification methods (silica-based DNA binding, agarose gel electrophoresis, ammonium acetate precipitation, and Sephadex G-200 gel filtration) for DNA recovery and removal of PCR inhibitors from crude extracts. Sephadex G-200 spin column purification was found to be the best method for removing PCR-inhibiting substances while minimizing DNA loss during purification. Our results indicate that for these types of samples, optimum DNA recovery requires brief, low-speed bead mill homogenization in the presence of a phosphate-buffered SDS-chloroform mixture, followed

  2. [Pollution evaluation and health risk assessment of heavy metals from atmospheric deposition in Lanzhou].

    Science.gov (United States)

    Li, Ping; Xue, Su-Yin; Wang, Sheng-Li; Nan, Zhong-Ren

    2014-03-01

    In order to evaluate the contamination and health risk of heavy metals from atmospheric deposition in Lanzhou, samples of atmospheric deposition were collected from 11 sampling sites respectively and their concentrations of heavy metals were determined. The results showed that the average contents of Cu, Pb, Cd, Cr, Ni, Zn and Mn were 82.22, 130.31, 4.34, 88.73, 40.64, 369.23 and 501.49 mg x kg(-1), respectively. There was great difference among different functional areas for all elements except Mn. According to the results, the enrichment factor score of Mn was close to 1, while the enrichment of Zn, Ni, Cu and Cr was more serious, and Pb and Cd were extremely enriched. The assessment results of geoaccumulation index of potential ecological risk indicated that the pollution of Cd in the atmospheric deposition of Lanzhou should be classified as extreme degree, and that of Cu, Ni, Zn, Pb as between slight and extreme degrees, and Cr as practically uncontaminated. Contaminations of atmospheric dust by heavy metals in October to the next March were more serious than those from April to August. Health risk assessment indicated that the heavy metals in atmospheric deposition were mainly ingested by human bodies through hand-mouth ingestion. The non-cancer risk was higher for children than for adults. The order of non-cancer hazard indexes of heavy metals was Pb > Cr > Cd > Cu > Ni > Zn. The non-cancer hazard indexes and carcinogen risks of heavy metals were both lower than their threshold values, suggesting that they will not harm the health.

  3. Evaluating the rate of migration of an uranium deposition front within the Uitenhage Aquifer

    CSIR Research Space (South Africa)

    Vogel

    1999-07-01

    Full Text Available of Geochemical Exploration 66 (1999) 269?276 www.elsevier.com/locate/jgeoexp Evaluating the rate of migration of an uranium deposition front within the Uitenhage Aquifer J.C. Vogel a,A.S.Talmaa, T.H.E. Heaton b, J. Kronfeld c,* a Quaternary Dating Research Unit... stream_source_info vogel_1999.pdf.txt stream_content_type text/plain stream_size 18078 Content-Encoding ISO-8859-1 stream_name vogel_1999.pdf.txt Content-Type text/plain; charset=ISO-8859-1 ELSEVIER Journal...

  4. An early approach for the evaluation of repair processes in fish after exposure to sediment contaminated by an oil spill.

    Science.gov (United States)

    Salamanca, Maria J; Jimenez-Tenorio, Natalia; Reguera, Diana F; Morales-Caselles, Carmen; Delvalls, T Angel

    2008-12-01

    A chronic bioassay was carried out under laboratory conditions using juvenile Solea senegalensis to determine the toxicity of contaminants from an oil spill(Prestige). Also, the repair processes in fish affected by contaminants due to oil exposure were evaluated. Over 30 days individuals were exposed to clean sediment (control) and to sediment contaminated by a mixture of polyaromatic hydrocarbons (PAHs) and other substances. The physicochemical parameters of the tanks (salinity, temperature, pH and dissolved oxygen) were controlled during the exposure period. Clean sediment from the Bay of Cadiz (Spain) was used as negative control and was mixed with fuel oil to prepare the dilution (0.5% w:w dry-weight). After the exposure period, fish were labeled and transferred to "clean tanks" (tanks without sediment) in order to study the recovery and the repair processes in the exposed organisms. A biomarker of exposure (ethoxyresorufin-O-deethylase activity - EROD activity) and a biomarker of effect (histopathology) were analyzed during the exposure and recovery period. After 10, 20 and 30 days of exposure, individuals showed significant induction (P tank", enabled a first evaluation of the repair process of the induced damages due to the fuel oil exposure. After the recovery phase, control individuals showed a more significant decrease (P repair processes probably need longer recovery periods to observe significant improvement of the affected organs. This will be further investigated in the future.

  5. Evaluate of head loss, sediment value and copper removal in sand media (rapid sand filter

    Directory of Open Access Journals (Sweden)

    Daneshi Navab

    2014-06-01

    Full Text Available Along with the technology development and increasing consumption of water resources, we are experiencing low qualities in the mentioned resources. Copper brings about serious environment al pollution, threatening human health and ecosystem. This metal found variously in water resources and industrial activities. Therefore, it needs to treat the water resources from these excessive amounts. Different methods have used for this reason but the most used method during recent years has been the absorption by economic absorbers such as sand. Rapid sand filters usually used in water and wastewater treatment plants for water clarification. In this research, a single layer gravity rapid sand filter has used to reduce different concentrations of copper. sediment value and head loss arising in filter media is simulated by using combination of Carman-Kozeny, Rose and Gregory models in different discharges of rapid sand filter. Results have shown that with increasing in discharge and decreasing in input copper concentration, arriving time to given head loss, is increasing. In addition, results demonstrated that with increasing in copper concentration in influent, removal efficiency is decreasing somewhat. Results of this research can applied in an appropriate design of rapid sand filter to copper removal, a prediction of rapid sand filter ability to copper removal and an estimation of arising head loss during filter work thus evaluating of time interval backwash. DOI: http://dx.doi.org/10.3126/ije.v3i2.10641 International Journal of the Environment Vol.3(2 2014: 276-286

  6. Evaluation of the anthropogenic radionuclide concentrations in sediments and fauna collected in the Beaufort Sea and northern Alaska

    International Nuclear Information System (INIS)

    Efurd, D.W.; Miller, G.G.; Rokop, D.J.

    1997-07-01

    This study was performed to establish a quality controlled data set about the levels of radio nuclide activity in the environment and in selected biota in the U.S. Arctic. Sediment and biota samples were collected by the National Oceanic and Atmospheric Administration (NOAA), the National Biological Service, and the North Slope Borough's Department of Wildlife Management to determine the impact of anthropogenic radionuclides in the Arctic. The results summarized in this report are derived from samples collected in northwest Alaska with emphasis on species harvested for subsistence in Barrow, Alaska. Samples were analyzed for the anthropogenic radionuclides 90 Sr, 137 Cs, 238 Pu, 239 Pu, 240 Pu and 241 Am. The naturally occurring radionuclides 40 K, 212 Pb and 214 Pb were also measured. One goal of this study was to determine the amounts of anthropogenic radionuclides present in the Beaufort Sea. Sediment samples were isotopically fingerprinted to determine the sources of radio nuclide activities. Biota samples of subsistence and ecological value were analyzed to search for evidence of bio-accumulation of radionuclides and to determine the radiation exposures associated with subsistence living in northern Alaska. The anthropogenic radio nuclide content of sediments collected in the Beaufort Sea was predominantly the result of the deposition of global fallout. No other sources of anthropogenic radionuclides could be conclusively identified in the sediments. The anthropogenic radio nuclide concentrations in fish, birds and mammals were very low. Assuming that ingestion of food is an important pathway leading to human contact with radioactive contaminants and given the dietary patterns in coastal Arctic communities, it can be surmised that marine food chains are presently not significantly affected

  7. Microbial Mn(IV) and Fe(III) reduction in northern Barents Sea sediments under different conditions of ice cover and organic carbon deposition

    DEFF Research Database (Denmark)

    Nickel, Maren; Vandieken, Verona; Brüchert, Volker

    2008-01-01

    station, with seasonally extended ice cover, low organic carbon content and sedimentation rate combined with relatively high concentrations of Mn and Fe(III) oxides favored dissimilatory Fe and Mn reduction (98% of anaerobic carbon oxidation) over sulfate reduction in the top 12 cm of the sediment....... In contrast, in a sediment that had not been ice covered for at least 12 months and with more organic carbon and a higher sedimentation rate, sulfate reduction was the most important anaerobic electron-accepting process (>80% of anaerobic carbon oxidation). In the upper 3 cm, microbial Fe and sulfate...

  8. Multiple sources of selenium in ancient seafloor hydrothermal systems: Compositional and Se, S, and Pb isotopic evidence from volcanic-hosted and volcanic-sediment-hosted massive sulfide deposits of the Finlayson Lake District, Yukon, Canada

    Science.gov (United States)

    Layton-Matthews, Daniel; Leybourne, Matthew I.; Peter, Jan M.; Scott, Steven D.; Cousens, Brian; Eglington, Bruce M.

    2013-09-01

    Volcanic-hosted massive sulfide (VHMS) and volcanic-sediment-hosted massive sulfide (VSHMS; i.e., hosted by both volcanic and sedimentary rocks) deposits in the Finlayson Lake District, Yukon, Canada, provide a unique opportunity to study the influence of seafloor and sub-seafloor hydrothermal processes on the formation of Se-poor (GP4F VHMS deposit; 7 ppm Se average), intermediate (Kudz Ze Kayah—KZK VHMS deposit; 200 ppm Se average), and Se-enriched (Wolverine VSHMS deposit; 1100 ppm Se average) mineralization. All three deposits are hosted by mid-Paleozoic (˜360-346 Ma) felsic volcanic rocks, but only the Wolverine deposit has voluminous coeval carbonaceous argillites (black shales) in the host rock package. Here we report the first application of Se isotope analyses to ancient seafloor mineralization and use these data, in conjunction with Pb and S isotope analyses, to better understand the source(s) and depositional process(es) of Se within VHMS and VSHMS systems. The wide range of δ82Se (-10.2‰ to 1.3‰, relative to NIST 3149), δ34S (+2.0‰ to +12.8‰ CDT), and elevated Se contents (up to 5865 ppm) within the Wolverine deposit contrast with the narrower range of δ82Se (-3.8‰ to -0.5‰), δ34S (9.8‰ to 13.0‰), and lower Se contents (200 ppm average) of the KZK deposit. The Wolverine and KZK deposits have similar sulfide depositional histories (i.e., deposition at the seafloor, with concomitant zone refining). The Se in the KZK deposit is magmatic (leaching or degassing) in origin, whereas the Wolverine deposit requires an additional large isotopically negative Se source (i.e. ˜-15‰ δ82Se). The negative δ82Se values for the Wolverine deposit are at the extreme light end for measured terrestrial samples, and the lightest observed for hypogene sulfide minerals, but are within calculated equilibrium values of δ82Se relative to NIST 3149 (˜30‰ at 25 °C between SeO4 and Se2-). We propose that the most negative Se isotope values at the

  9. Evaluating suitability of MODIS-Terra images for reproducing historic sediment concentrations in water bodies: Lake Tana, Ethiopia

    Science.gov (United States)

    Kaba, Essayas; Philpot, William; Steenhuis, Tammo

    2014-02-01

    Government and NGO funded conservation programs are being implemented in developing countries with the potential benefit of reduced sediment inflow into fresh water lakes. However, these claims are difficult to verify due to limited historical sediment concentration data in lakes and rivers. Remote sensing can potentially aid in monitoring sediment concentration. With almost daily availability over the past ten years and consistent atmospheric correction applied to the images, Moderate Resolution Imaging Spectroradiometer (MODIS) 250 meter images are potential resources capable of monitoring future concentrations and reconstructing historical sediment concentration records. In this paper, site-specific relationships are developed between reflectance in near-infrared (NIR) images and three factors: total suspended solids (TSS), turbidity and Secchi depth for Lake Tana near the mouth of the Gumara River. The first two sampling campaigns on November 27, 2010 and May 13, 2011 are used in calibration. Reflectance in the NIR varies linearly with turbidity (R2 = 0.89) and TSS (R2 = 0.95). Secchi depth fit best to an exponential relation with R2 of 0.74. The relationships are validated using a third sample set collected on November 7, 2011 with RMSE of 11 Nephelometric Turbidity Units (NTU) for Turbidity, 16.5 mg l-1 for TSS and 0.12 meters for Secchi depth. The MAE was 10% for TSS, 14% for turbidity and 0.1% for Secchi depth. Using the relationship for TSS, a 10-year time series of sediment concentration in Lake Tana near the Gumara River was plotted. It was found that after the severe drought of 2002 and 2003 the concentration in the lake increased significantly. The results showed that MODIS images are potential cost effective tools to monitor suspended sediment concentration and obtain a past history of concentration for evaluating the effect of best management practices.

  10. Heat transfer from a high temperature condensable mixture. II. Sedimentation of fog condensate

    International Nuclear Information System (INIS)

    Condiff, D.W.; Cho, D.H.; Chan, S.H.

    1985-01-01

    A kinematic wave analysis of fog sedimentation is employed to relate growth of a fog condensate deposit layer to radiation generated fog formation rates. The increase of surface radiation absorptivity with deposit layer thickness promotes a feedback mechanism for higher growth rates, which is evaluated in detail

  11. Study of recent sediment accumulation rate using 210Pb around Mumbai Harbor Bay

    International Nuclear Information System (INIS)

    Chaudhury, Moushumi D.; Pulhani, Vandana; Jha, S.K.; Tripathi, R.M.

    2016-01-01

    The study of the coastal marine sediment of Mumbai harbor bay (MHB) provides a significant insight of the stress due to unprecedented increase of anthropogenic activities in and around the bay and climatic changes. This encourages archiving the sediments for characterizing the depositional environment of water system by examining the sediment accumulation rate (SAR) to understand thc annual deposition of chemical contaminants. The study of SAR evaluates the fate and potential effects of chemical contaminants which when discharged into aquatic environment quickly become attached to sediment particles at different exchange sites. The rate of sediment accumulation has a significant impact on many geochemical processes; it is also vital for the functioning of benthic organisms in this environment, particularly the seabed fauna. SAR is calculated from sedimentation rate, bulk density and porosity

  12. An evaluation of dry deposition from the long range atmospheric dispersion

    International Nuclear Information System (INIS)

    Suh, K.S.; Kim, E.H.; Hwang, W.T.; Han, M.H.; Lee, H.S.; Lee, C.W.

    2003-01-01

    The dry deposition of pollutants released into the atmosphere must be evaluated to estimate the radiological dose of terrestrial plants and foodstuffs in the ecosystem. Especially, the atmospheric dispersion and dry deposition models have been widely developed to predict and minimize the radiological damage for the surrounding environment after the TMI-2 and the Chernobyl accidents. A Lagrangian particle model for the evaluation the long-range dispersion has been firstly developed in Korea since 2001. The particle tracking method was used for the estimation of the concentration distribution of the radioactive materials released into the atmosphere. The model is designed to estimate air concentration and ground deposition at distances up to some thousands of kilometers from the source point in the horizontal direction. The turbulent motion is considered to separate the treatment of particles within the mixing layer and above the mixing layer. Also, the dispersion model is designed to receive the results of the MM5 model being operated by KMA (Korea Meteorological Administration). The test run of the long-range dispersion model has been performed in the area which covered extends from 102.47deg E to 173.34deg E and from 12.27deg N to 53.72deg N in Northeast Asia. The release point of Cs-137 assumed in the east part of the China. The long range dispersion model has been firstly developed to estimate the radiological consequences against a nuclear accident. The model will be supplemented by the comparative study using the data of the ETEX experiments. (author)

  13. In-Well Sediment Incubators to Evaluate Microbial Community Stability and Dynamics following Bioimmobilization of Uranium

    International Nuclear Information System (INIS)

    Baldwin, Brett R.; Peacock, Aaron D.; Gan, M.; Resch, Charles T.; Arntzen, Evan V.; Smithgall, A.N.; Pfiffner, S.; Freifeld, Barry M.; White, D.C.; Long, Philip E.

    2009-01-01

    An in-situ incubation device (ISI) was developed in order to investigate the stability and dynamics of sediment associated microbial communities to prevailing subsurface oxidizing or reducing conditions. Here we describe the use of these devices at the Old Rifle Uranium Mill Tailings Remedial Action (UMTRA) site. During the 7 month deployment oxidized Rifle aquifer background sediments (RABS) were deployed in previously biostimulated wells under iron reducing conditions, cell densities of known iron reducing bacteria including Geobacteraceae increased significantly showing the microbial community response to local subsurface conditions. PLFA profiles of RABS following in situ deployment were strikingly similar to those of adjacent sediment cores suggesting ISI results could be extrapolated to the native material of the test plots. Results for ISI deployed reduced sediments showed only slight changes in community composition and pointed toward the ability of the ISIs to monitor microbial community stability and response to subsurface conditions.

  14. Evaluation of clean-up agents for total petroleum hydrocarbon analysis in biota and sediments.

    NARCIS (Netherlands)

    Muijs, B.; Jonker, M.T.O.

    2009-01-01

    Petroleum hydrocarbons (oil) are common environmental contaminants. For risk assessment purposes, their concentrations in environmental matrixes, such as biota and soils/sediments are frequently determined by solvent extraction and subsequent analysis with gas chromatography (GC) equipped with flame

  15. An evaluation of bioremediation of oiled sediments buried within a mudflat environment

    International Nuclear Information System (INIS)

    Swannell, R. P. J.; Mitchell, D. J.; Jones, D. M.; Willis, A. L.; Lee, K.

    1997-01-01

    An investigation was carried out to determine the potential of bioremediation to treat an oil-contaminated shoreline sediment in the southwest of England. The specific objective was to determine whether periodic additions of inorganic nitrate and phosphate could be used to enhance the biodegradation rate of weathered and emulsified Arabian Light crude oil-contaminated sediment stranded on the beach at a depth of about 15 cm. To measure the potential for successful treatment, changes in the chemical composition and concentration of residual hydrocarbons, microbial carbon dioxide production rates in situ and in the hydrocarbon-degrading microbial community, were monitored. Results showed that regular additions of inorganic nutrients significantly enhanced the rate of oil biodegradation in comparison with unfertilized oil sediments, indicating that bioremediation could be successful in treating buried oil in aerobic fine sediments.17 refs., 4 tabs., 4 figs

  16. Evaluating order in vertical successions of deltaic Holocene sediments on the Ganges-Brahmaputra-Meghna delta

    Science.gov (United States)

    Sincavage, R.; Goodbred, S. L., Jr.

    2017-12-01

    Most stratigraphic models are predicated on the presence of cyclicity or some form of order in vertical successions of strata. In spite of this a priori assumption of ordered stratigraphy, rarely are statistical metrics employed to quantify cyclicity in sedimentary packages. The presence or absence of preserved order in vertical sedimentary successions has important implications for the nature of environmental signals that are transmitted into the rock record. We interrogate the Holocene sedimentary archive of the Ganges-Brahmaputra-Meghna delta (GBMD) in an effort to explore to what extent fluvio-deltaic deposits exhibit recognizable order. Specifically, we focus on grain size data to evaluate 1.) if stratigraphic order in vertical sedimentary successions can be identified and quantified, and 2.) if there are spatial patterns of stratigraphic order across the GBMD. A runs order metric r is used to identify sequences of coarsening and fining within an extensive borehole network. Observed grain size data are shuffled enough times to generate synthetic "random" stratigraphy, and a Monte Carlo simulation generates 5000 realizations. The distribution of r values from the Monte Carlo are compared to the r metric calculated from observed data to determine how likely the observed metric could be generated by chance. The spatial distribution of order metrics indicates a relationship between areas of enhanced mass extraction and preservation of fluvial successions that scale with modern bar deposits on the Jamuna River. Similarly, probability metrics indicate that vertical successions of grain size data unlikely to have been generated by chance are more likely to be found on distal areas of the delta where 60% of the input mass has been extracted. Combining a mass balance framework with simple statistical metrics has the potential of improving predictions of the stratigraphic architecture and the preservation of ordered vs. disordered signals in the sedimentary record.

  17. Tidal wetland fluxes of dissolved organic carbon and sediment at Browns Island, California: initial evaluation

    Science.gov (United States)

    Ganju, N.K.; Bergamaschi, B.; Schoellhamer, D.H.

    2003-01-01

    Carbon and sediment fluxes from tidal wetlands are of increasing concern in the Sacramento-San Joaquin River Delta (Delta), because of drinking water issues and habitat restoration efforts. Certain forms of dissolved organic carbon (DOC) react with disinfecting chemicals used to treat drinking water, to form disinfection byproducts (DBPs), some of which are potential carcinogens. The contribution of DBP precursors by tidal wetlands is unknown. Sediment transport to and from tidal wetlands determines the potential for marsh accretion, thereby affecting habitat formation.Water, carbon, and sediment flux were measured in the main channel of Browns Island, a tidal wetland located at the confluence of Suisun Bay and the Delta. In-situ instrumentation were deployed between May 3 and May 21, 2002. Water flux was measured using acoustic Doppler current profilers and the index-velocity method. DOC concentrations were measured using calibrated ultraviolet absorbance and fluorescence instruments. Suspended-sediment concentrations were measured using a calibrated nephelometric turbidity sensor. Tidally averaged water flux through the channel was dependent on water surface elevations in Suisun Bay. Strong westerly winds resulted in higher water surface elevations in the area east of Browns Island, causing seaward flow, while subsiding winds reversed this effect. Peak ebb flow transported 36% more water than peak flood flow, indicating an ebb-dominant system. DOC concentrations were affected strongly by porewater drainage from the banks of the channel. Peak DOC concentrations were observed during slack after ebb, when the most porewater drained into the channel. Suspended-sediment concentrations were controlled by tidal currents that mobilized sediment from the channel bed, and stronger tides mobilized more sediment than the weaker tides. Sediment was transported mainly to the island during the 2-week monitoring period, though short periods of export occurred during the spring

  18. A free tool integrating GIS features and workflows to evaluate sediment connectivity in alpine catchments

    Science.gov (United States)

    Crema, Stefano; Schenato, Luca; Goldin, Beatrice; Marchi, Lorenzo; Cavalli, Marco

    2014-05-01

    The increased interest in sediment connectivity has brought the geomorphologists' community to focus on sediment fluxes as a key process (Cavalli et al., 2013; Heckmann and Schwanghart, 2013). The challenge of dealing with erosion-related processes in alpine catchments is of primary relevance for different fields of investigations and applications, including, but not limited to natural hazards, hydraulic structures design, ecology and stream restoration. The present work focuses on the development of a free tool for sediment connectivity assessment as described in Cavalli et al. (2013), introducing some novel improvements. The choice of going for a free software is motivated by the need of widening the access and improving participation beyond the restrictions on algorithms customization, typical of commercial software. A couple of features further enhance the tool: being completely free and adopting a user-friendly interface, its target audience includes researchers and stakeholders (e.g., local managers and civil protection authorities in charge of planning the priorities of intervention in the territory), being written in Python programming language, it can benefit from optimized algorithms for high-resolution DEMs (Digital Elevation Models) handling and for propagation workflows implementation; these two factors make the tool computationally competitive with the most recent commercial GIS products. The overall goal of this tool is supporting the analysis of sediment connectivity, facing the challenge of widening, as much as possible, the users' community among scientists and stakeholders. This aspect is crucial, as future improvement of this tool will benefit of feedbacks from users in order to improve the quantitative assessment of sediment connectivity as a major input information for the optimal management of mountain areas. References: Cavalli, M., Trevisani, S., Comiti, F., Marchi, L., 2013. Geomorphometric assessment of spatial sediment connectivity in

  19. Identifying and Evaluating Options for Improving Sediment Management and Fish Passage at Hydropower Dams in the Lower Mekong River Basin

    Science.gov (United States)

    Wild, T. B.; Reed, P. M.; Loucks, D. P.

    2015-12-01

    The Mekong River basin in Southeast Asia is undergoing intensive and pervasive hydropower development to satisfy demand for increased energy and income to support its growing population of 60 million people. Just 20 years ago this river flowed freely. Today some 30 large dams exist in the basin, and over 100 more are being planned for construction. These dams will alter the river's natural water, sediment and nutrient flows, thereby impacting river morphology and ecosystems, and will fragment fish migration pathways. In doing so, they will degrade one of the world's most valuable and productive freshwater fish habitats. For those dams that have not yet been constructed, there still exist opportunities to modify their siting, design and operation (SDO) to potentially achieve a more balanced set of tradeoffs among hydropower production, sediment/nutrient passage and fish passage. We introduce examples of such alternative SDO opportunities for Sambor Dam in Cambodia, planned to be constructed on the main stem of the Mekong River. To evaluate the performance of such alternatives, we developed a Python-based simulation tool called PySedSim. PySedSim is a daily time step mass balance model that identifies the relative tradeoffs among hydropower production, and flow and sediment regime alteration, associated with reservoir sediment management techniques such as flushing, sluicing, bypassing, density current venting and dredging. To date, there has been a very limited acknowledgement or evaluation of the significant uncertainties that impact the evaluation of SDO alternatives. This research is formalizing a model diagnostic assessment of the key assumptions and parametric uncertainties that strongly influence PySedSim SDO evaluations. Using stochastic hydrology and sediment load data, our diagnostic assessment evaluates and compares several Sambor Dam alternatives using several performance measures related to energy production, sediment trapping and regime alteration, and

  20. [Pollution Evaluation and Risk Assessment of Heavy Metals from Atmospheric Deposition in the Parks of Nanjing].

    Science.gov (United States)

    Wang, Cheng; Qian, Xin; Li, Hui-ming; Sun, Yi-xuan; Wang, Jin-hua

    2016-05-15

    Contents of heavy metals involving As, Cd, Cr, Cu, Ni, Pb and Zn from atmospheric deposition in 10 parks of Nanjing were analyzed. The pollution level, ecological risk and health risk were evaluated using Geoaccumulation Index, Potential Ecological Risk Index and the US EPA Health Risk Assessment Model, respectively. The results showed that the pollution levels of heavy metals in Swallow Rock Park, Swallow Rock Park and Mochou Lake Park were higher than the others. Compared to other cities such as Changchun, Wuhan and Beijing, the contents of heavy metals in atmospheric deposition of parks in Nanjing were higher. The evaluation results of Geoaccumulation Index showed that Pb was at moderate pollution level, Zn and Cu were between moderate and serious levels, while Cd was between serious and extreme levels. The ecological risk level of Cd was high. The assessment results of Health Risk Assessment Model indicated that there was no non-carcinogenic risk for all the seven heavy metals. For carcinogenic risk, the risks of Cd, Cr and Ni were all negligible (Risk < 1 x 10⁻⁶), whereas As had carcinogenic risk possibility but was considered to be acceptable (10⁻⁶ < Risk < 10⁻⁴).

  1. Evaluation of cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Woo, Sang Keun; Kim, Wook; Park, Yong Sung; Kang, Joo Hyun; Lee, Yong Jin [Korea Institute of Radiological and Medical Sciences, KIRAMS, Seoul (Korea, Republic of); Cho, Doo Wan; Lee, Hong Soo; Han, Su Cheol [Jeonbuk Department of Inhalation Research, Korea Institute of toxicology, KRICT, Jeongeup (Korea, Republic of)

    2016-12-15

    These absorbed dose can calculated using the Monte Carlo transport code MCNP (Monte Carlo N-particle transport code). Internal radiotherapy absorbed dose was calculated using conventional software, such as OLINDA/EXM or Monte Carlo simulation. However, the OLINDA/EXM does not calculate individual absorbed dose and non-standard organ, such as tumor. While the Monte Carlo simulation can calculated non-standard organ and specific absorbed dose using individual CT image. External radiotherapy, absorbed dose can calculated by specific absorbed energy in specific organs using Monte Carlo simulation. The specific absorbed energy in each organ was difference between species or even if the same species. Since they have difference organ sizes, position, and density of organs. The aim of this study was to individually evaluated cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation. We evaluation of cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation. The absorbed energy in each organ compared with mouse heart was 54.6 fold higher than monkey absorbed energy in heart. Likewise lung was 88.4, liver was 16.0, urinary bladder was 29.4 fold higher than monkey. It means that the distance of each organs and organ mass was effects of the absorbed energy. This result may help to can calculated absorbed dose and more accuracy plan for external radiation beam therapy and internal radiotherapy.

  2. Evaluation of cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation

    International Nuclear Information System (INIS)

    Woo, Sang Keun; Kim, Wook; Park, Yong Sung; Kang, Joo Hyun; Lee, Yong Jin; Cho, Doo Wan; Lee, Hong Soo; Han, Su Cheol

    2016-01-01

    These absorbed dose can calculated using the Monte Carlo transport code MCNP (Monte Carlo N-particle transport code). Internal radiotherapy absorbed dose was calculated using conventional software, such as OLINDA/EXM or Monte Carlo simulation. However, the OLINDA/EXM does not calculate individual absorbed dose and non-standard organ, such as tumor. While the Monte Carlo simulation can calculated non-standard organ and specific absorbed dose using individual CT image. External radiotherapy, absorbed dose can calculated by specific absorbed energy in specific organs using Monte Carlo simulation. The specific absorbed energy in each organ was difference between species or even if the same species. Since they have difference organ sizes, position, and density of organs. The aim of this study was to individually evaluated cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation. We evaluation of cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation. The absorbed energy in each organ compared with mouse heart was 54.6 fold higher than monkey absorbed energy in heart. Likewise lung was 88.4, liver was 16.0, urinary bladder was 29.4 fold higher than monkey. It means that the distance of each organs and organ mass was effects of the absorbed energy. This result may help to can calculated absorbed dose and more accuracy plan for external radiation beam therapy and internal radiotherapy.

  3. Incorporation of Fine-Grained Sediment Erodibility Measurements into Sediment Transport Modeling, Capitol Lake, Washington

    Science.gov (United States)

    Stevens, Andrew W.; Gelfenbaum, Guy; Elias, Edwin; Jones, Craig

    2008-01-01

    Capitol Lake was created in 1951 with the construction of a concrete dam and control gate that prevented salt-water intrusion into the newly formed lake and regulated flow of the Deschutes River into southern Puget Sound. Physical processes associated with the former tidally dominated estuary were altered, and the dam structure itself likely caused an increase in retention of sediment flowing into the lake from the Deschutes River. Several efforts to manage sediment accumulation in the lake, including dredging and the construction of sediment traps upriver, failed to stop the lake from filling with sediment. The Deschutes Estuary Feasibility Study (DEFS) was carried out to evaluate the possibility of removing the dam and restoring estuarine processes as an alternative ongoing lake management. An important component of DEFS was the creation of a hydrodynamic and sediment transport model of the restored Deschutes Estuary. Results from model simulations indicated that estuarine processes would be restored under each of four restoration alternatives, and that over time, the restored estuary would have morphological features similar to the predam estuary. The model also predicted that after dam-removal, a large portion of the sediment eroded from the lake bottom would be deposited near the Port of Olympia and a marina located in lower Budd Inlet seaward of the present dam. The volume of sediment transported downstream was a critical piece of information that managers needed to estimate the total cost of the proposed restoration project. However, the ability of the model to predict the magnitude of sediment transport in general and, in particular, the volume of sediment deposition in the port and marina was limited by a lack of information on the erodibility of fine-grained sediments in Capitol Lake. Cores at several sites throughout Capitol Lake were collected between October 31 and November 1, 2007. The erodibility of sediments in the cores was later determined in the

  4. Sediment and toxic contaminant transport modeling in coastal waters

    International Nuclear Information System (INIS)

    Onishi, Y.; Mayer, D.W.; Argo, R.S.

    1982-02-01

    A hydrodynamic model, CAFE-I, a wave refraction model, LO3D, and a sediment and contaminant transport model, FETRA, were selected as tools for evaluating exposure levels of radionuclides, heavy metals, and other toxic chemicals in coastal waters. Prior to the application of these models to the Irish Sea and other coastal waters, the finite element model, FETRA, was tested to demonstrate its ability to simulate sediment and contaminant interactions (e.g., adsorption and desorption), and the mechanisms governing the transport, deposition, and resuspension of contaminated sediments

  5. Mrica Reservoir Sedimentation: Current Situation and Future Necessary Management

    Directory of Open Access Journals (Sweden)

    Puji Utomo

    2017-09-01

    Full Text Available Mrica Reservoir is one of many reservoirs located in Central Java that experienced a considerably high sedimentation during the last ten years. This condition has caused a rapid decrease in reservoir capacity. Various countermeasures have been introduced to reduce the rate of the reservoir sedimentation through catchment management and reservoir operation by means of flushing and/or dredging. However, the sedimentation remains intensive so that the fulfillment of water demand for electrical power generation was seriously affected. This paper presents the results of evaluation on the dynamics of the purpose of this research is to evaluate the sediment balance of the Mrica Reservoir based on two different scenarios, i.e. the existing condition and another certain type of reservoir management. The study on sediment balance was carried out by estimating the sediment inflow applying sheet erosion method in combination with the analysis of sediment rating curve. The measurement of the deposited sediment rate in the reservoir was conducted through the periodic echo sounding, whereas identification of the number of sediment that has been released from the reservoir was carried out through the observation on both flushing and dredging activities. The results show that during the last decade, the rate of the sediment inflow was approximately 5.869 MCM/year, whereas the released sediment from the reservoir was 4.097 MCM/year. In order to maintain the reservoir capacity, therefore, at least 1.772 MCM/year should be released from the reservoir by means of either flushing or dredging. Sedimentation management may prolong the reservoir’s service life to exceed the design life. Without sediment management, the lifetime of the reservoir would have finished by 2016, whereas with the proper management the lifetime may be extended to 2025.

  6. Evaluation of five dry particle deposition parameterizations for incorporation into atmospheric transport models

    Science.gov (United States)

    Khan, Tanvir R.; Perlinger, Judith A.

    2017-10-01

    Despite considerable effort to develop mechanistic dry particle deposition parameterizations for atmospheric transport models, current knowledge has been inadequate to propose quantitative measures of the relative performance of available parameterizations. In this study, we evaluated the performance of five dry particle deposition parameterizations developed by Zhang et al. (2001) (Z01), Petroff and Zhang (2010) (PZ10), Kouznetsov and Sofiev (2012) (KS12), Zhang and He (2014) (ZH14), and Zhang and Shao (2014) (ZS14), respectively. The evaluation was performed in three dimensions: model ability to reproduce observed deposition velocities, Vd (accuracy); the influence of imprecision in input parameter values on the modeled Vd (uncertainty); and identification of the most influential parameter(s) (sensitivity). The accuracy of the modeled Vd was evaluated using observations obtained from five land use categories (LUCs): grass, coniferous and deciduous forests, natural water, and ice/snow. To ascertain the uncertainty in modeled Vd, and quantify the influence of imprecision in key model input parameters, a Monte Carlo uncertainty analysis was performed. The Sobol' sensitivity analysis was conducted with the objective to determine the parameter ranking from the most to the least influential. Comparing the normalized mean bias factors (indicators of accuracy), we find that the ZH14 parameterization is the most accurate for all LUCs except for coniferous forest, for which it is second most accurate. From Monte Carlo simulations, the estimated mean normalized uncertainties in the modeled Vd obtained for seven particle sizes (ranging from 0.005 to 2.5 µm) for the five LUCs are 17, 12, 13, 16, and 27 % for the Z01, PZ10, KS12, ZH14, and ZS14 parameterizations, respectively. From the Sobol' sensitivity results, we suggest that the parameter rankings vary by particle size and LUC for a given parameterization. Overall, for dp = 0.001 to 1.0 µm, friction velocity was one of

  7. Evaluation of five dry particle deposition parameterizations for incorporation into atmospheric transport models

    Directory of Open Access Journals (Sweden)

    T. R. Khan

    2017-10-01

    Full Text Available Despite considerable effort to develop mechanistic dry particle deposition parameterizations for atmospheric transport models, current knowledge has been inadequate to propose quantitative measures of the relative performance of available parameterizations. In this study, we evaluated the performance of five dry particle deposition parameterizations developed by Zhang et al. (2001 (Z01, Petroff and Zhang (2010 (PZ10, Kouznetsov and Sofiev (2012 (KS12, Zhang and He (2014 (ZH14, and Zhang and Shao (2014 (ZS14, respectively. The evaluation was performed in three dimensions: model ability to reproduce observed deposition velocities, Vd (accuracy; the influence of imprecision in input parameter values on the modeled Vd (uncertainty; and identification of the most influential parameter(s (sensitivity. The accuracy of the modeled Vd was evaluated using observations obtained from five land use categories (LUCs: grass, coniferous and deciduous forests, natural water, and ice/snow. To ascertain the uncertainty in modeled Vd, and quantify the influence of imprecision in key model input parameters, a Monte Carlo uncertainty analysis was performed. The Sobol' sensitivity analysis was conducted with the objective to determine the parameter ranking from the most to the least influential. Comparing the normalized mean bias factors (indicators of accuracy, we find that the ZH14 parameterization is the most accurate for all LUCs except for coniferous forest, for which it is second most accurate. From Monte Carlo simulations, the estimated mean normalized uncertainties in the modeled Vd obtained for seven particle sizes (ranging from 0.005 to 2.5 µm for the five LUCs are 17, 12, 13, 16, and 27 % for the Z01, PZ10, KS12, ZH14, and ZS14 parameterizations, respectively. From the Sobol' sensitivity results, we suggest that the parameter rankings vary by particle size and LUC for a given parameterization. Overall, for dp  =  0.001 to 1.0

  8. Evaluation of the stomatal conductance formulation in the EMEP ozone deposition model for Picea abies

    Science.gov (United States)

    Wieser, G.; Emberson, L. D.

    It is widely acknowledged that the possible impacts of ozone on forest trees are more closely related to ozone flux through the stomata than to external ozone exposure. However, the application of the flux approach on a European scale requires the availability of appropriate models, such as the European Monitoring and Evaluation Programme (EMEP) ozone deposition model, for estimating ozone flux and cumulative ozone uptake. Within this model stomatal conductance is the key variable, since it determines the amount of ozone absorbed by the leaves. This paper describes the suitability of the existing EMEP ozone deposition model parameterisation and formulation to represent stomatal behaviour determined from field measurements on adult Norway spruce ( Picea abies (L.) Karst.) trees in the Central European Alps. Parameters affecting maximum stomatal conductance (e.g. seasonal phenology, needle position, needle age, nutrient deficiency and ozone itself) and stomatal response functions to temperature, irradiance, vapour pressure deficit, and soil water content are investigated. Finally, current limitations and possible alterations of the EMEP model will be discussed with respect to spatial scales of available input data for future flux modelling.

  9. Accessibility evaluation of the IFMIF liquid lithium loop considering activated erosion/corrosion materials deposition

    International Nuclear Information System (INIS)

    Nakamura, H.; Takemura, M.; Yamauchi, M.; Fischer, U.; Ida, M.; Mori, S.; Nishitani, T.; Simakov, S.; Sugimoto, M.

    2005-01-01

    This paper presents an evaluation of accessibility of the Li loop piping considering activated corrosion product. International Fusion Materials Irradiation Facility (IFMIF) is a deuteron-lithium (Li) stripping reaction neutron source for fusion materials testing. Target assembly and back wall are designed as fully remote maintenance component. Accessibility around the Li loop piping will depend on activation level of the deposition materials due to the back wall erosion/corrosion process under liquid Li flow. Activation level of the corrosion products coming from the AISI 316LN back wall is calculated by the ACT-4 of the THIDA-2 code system. The total activities after 1 day, 1 week, 1 month and 1 year cooling are 3.1 x 10 14 , 2.8 x 10 14 , 2.3 x 10 14 and 7.5 x 10 13 Bq/kg, respectively. Radiation dose rate around the Li loop pipe is calculated by QAD-CGGP2R code. Activated area of the back wall is 100 cm 2 . Corrosion rate is assumed 1 μm/year. When 10% of the corrosion material is supposed to be deposited on the inner surface of the pipe, the dose rate is calculated to be less than a permissible level of 10 μSv/h for hands-on maintenance, therefore, the maintenance work is assessed to be possible

  10. Visual classification of very fine-grained sediments: Evaluation through univariate and multivariate statistics

    Science.gov (United States)

    Hohn, M. Ed; Nuhfer, E.B.; Vinopal, R.J.; Klanderman, D.S.

    1980-01-01

    Classifying very fine-grained rocks through fabric elements provides information about depositional environments, but is subject to the biases of visual taxonomy. To evaluate the statistical significance of an empirical classification of very fine-grained rocks, samples from Devonian shales in four cored wells in West Virginia and Virginia were measured for 15 variables: quartz, illite, pyrite and expandable clays determined by X-ray diffraction; total sulfur, organic content, inorganic carbon, matrix density, bulk density, porosity, silt, as well as density, sonic travel time, resistivity, and ??-ray response measured from well logs. The four lithologic types comprised: (1) sharply banded shale, (2) thinly laminated shale, (3) lenticularly laminated shale, and (4) nonbanded shale. Univariate and multivariate analyses of variance showed that the lithologic classification reflects significant differences for the variables measured, difference that can be detected independently of stratigraphic effects. Little-known statistical methods found useful in this work included: the multivariate analysis of variance with more than one effect, simultaneous plotting of samples and variables on canonical variates, and the use of parametric ANOVA and MANOVA on ranked data. ?? 1980 Plenum Publishing Corporation.

  11. Evaluation of Hydrogen Cracking in Weld Metal Deposited using Cellulosic-Coated Electrodes

    Science.gov (United States)

    2009-06-16

    Cellulosic-coated electrodes (primarily AWS EXX10-type) are traditionally used for "stovepipe" welding of pipelines because they are well suited for deposition of pipeline girth welds and are capable of high deposition rates when welding downhill. De...

  12. Automated electron microprobe identification of minerals in stream sediments for the national uranium resources evaluation program

    International Nuclear Information System (INIS)

    Mosley, W.C. Jr.

    1979-01-01

    Over 500 stream sediment particles have been analyzed. About 96% have been identified as distinct minerals. Most of the others appeared to be mixtures. Only zinc-bearing gahnite had to be analyzed further for positive identification. Monazite and zircon were the only minerals with concentrations of uranium significantly above the detection limit. The Frantz Isodynamic Magnetic Separator isolated the monazite into the 1.0 fraction. Monazite particles in anomalous sediments contained up to 3.7 wt % uranium. This uranium concentration is unusually high for monazite, which normally has about 0.5 wt % uranium, and may be the cause of the anomaly

  13. Energy and nutrient deposition and excretion in the reproducing sow: model development and evaluation

    DEFF Research Database (Denmark)

    Hansen, A V; Strathe, A B; Theil, Peter Kappel

    2014-01-01

    requirements for maintenance, and fetal and maternal growth were described. In the lactating module, a factorial approach was used to estimate requirements for maintenance, milk production, and maternal growth. The priority for nutrient partitioning was assumed to be in the order of maintenance, milk...... production, and maternal growth with body tissue losses constrained within biological limits. Global sensitivity analysis showed that nonlinearity in the parameters was small. The model outputs considered were the total protein and fat deposition, average urinary and fecal N excretion, average methane...... emission, manure carbon excretion, and manure production. The model was evaluated using independent data sets from the literature using root mean square prediction error (RMSPE) and concordance correlation coefficients. The gestation module predicted body fat gain better than body protein gain, which...

  14. LABORATORY EVALUATION OF ANDALIN, AN INSECT GROWTH REGULATOR INTERFERING WITH CUTICLE DEPOSITION, AGAINST MOSQUITO LARVAE

    Directory of Open Access Journals (Sweden)

    N REHIMI

    2002-12-01

    Full Text Available Andalin, a benzoylphenylurea (BPU derivative, was evaluated on Culex pipiens L. (Diptera: Culicidae. Treatment was made on newly 3rd- and 4th instar larvae for 24 h. The compound exhibited insecticidal activity and mortality occured after earlier inhibition of their development or by their inability to complete their ecdysis. Treatment resulted in a significant larvicidal effect and in a inhibition of adult emergence. Moreover, the compound disturbed growth and development since several morphological types and an increase in the duration of larval stage were observed. Histological study conducted on 4th instar larval integument, showed that Andalin caused a significant reduction in the thickness of cuticles secreted compared to controls. Thus, Andalin prevent molting in C. pipiens by interfering with cuticle deposition confirming the primary mode of action of this BPU insecticide.

  15. Post depositional memory record of mercury in sediment near effluent disposal site of a chlor-alkali plant in Thane Creek-Mumbai Harbour, India

    Digital Repository Service at National Institute of Oceanography (India)

    Ram, A.; Rokade, M.A.; Zingde, M.D.; Borole, D.V.

    in landfills, mine tailings, contaminated industrial sites, soils and sediments. Estuaries and coastal marine regions form an essential link in the global biogeochemical cycling of Hg between the terrestrial environment - the major repository for atmospheric... by close relationship with organic matter, and Fe and Al oxides or sorbed onto the mineral particles [8]. Hence, sediments adjacent to the outfalls of chlor-alkali plants frequently contain high levels of Hg [7,10-15]. Some natural processes (water, soil...

  16. OZONE AND SULFUR DIOXIDE DRY DEPOSITION TO FORESTS: OBSERVATIONS AND MODEL EVALUATION

    Science.gov (United States)

    Fluxes and deposition velocities of O3 and SO2 were measured over both a deciduous and a mixed coniferous-deciduous forest for full growing seasons. Fluxes and deposition velocities of O3 were measured over a coniferous forest for a month. Mean deposition velocities of 0.35 t...

  17. Corrosion and deposit evaluation in industrial plants by non destructive testing method

    International Nuclear Information System (INIS)

    Azali Muhammad; Abd Razak Hamzah; Abd Aziz Mohamed; Mohd Pauzi Ismail; S Saad; S Sayuti; S Ahmad

    2000-01-01

    In petrochemical plants, the detection of corrosion and evaluation of deposit in insulated pipes using a radiography method are very challenging tasks. This main degradation problem experienced by pipelines is due to water condensation. It will cause deposit and scale inside the pipe, as well as between the insulation and pipe for the cold temperature pipes. On the other hand, for the hot temperature pipes the main problem is mainly due to corrosion/erosion attack inside the pipe. In the case of corrosion study one of the most important parameters in a piping or pipeline to be monitored and measured is that the wall thickness. In general, most pipeline corrosion monitoring and evaluation for both insulated and non-insulated pipes is done by using an ultrasonic method. The most common technique for corrosion is that based on the A-Scan, using either a normal flow detector or some form of dedicated equipment. However, with recent development of ultrasonic technology, more advance method, namely B-Scan and C-scan techniques are also available. The most notable disadvantage of using this current method is that the insulation covered the pipe has to be removed before the inspection can be carried out and this is considered as not so cost effective. Due to this reason other alternative NDT method, namely radiographic testing method has been studied. The testing technique used in this studied are tangential technique and double wall radiographic technique which involve studying the changing in density of radiographic film. The result found using tangential technique is consistent with real thickness of the pipe. However for the later technique the result is only achieved with a reasonable accuracy when the changing in wall thickness is very small. The result of the studies is discussed in this paper

  18. Evaluation of the salt deposition on the canister surface of concrete cask. Part 3. Long-term measurement of salt concentration in air and evaluation of the salt deposition

    International Nuclear Information System (INIS)

    Wataru, Masumi; Takeda, Hirofumi

    2015-01-01

    To realize the dry storage using concrete cask in Japan, it is important to develop the evaluation method of the SCC of the canister. One of the key issues is sea salt deposition on the canister surface during the storage period. If the amount of salt deposition exceeds the critical value, the SCC may occur. The amount of salt deposition depends on the ambient air condition. We developed the measurement device of salt in air to make clear the ambient condition. The device sucks the air including sea salt and the sea salt dissolves in water. We analyze the water including sea salt. This device works automatically for one or two months. In this study, the performance of this device was verified comparing the data obtained by the air sampler using filter pack. In Yokosuka area of CRIEPI, we measured the ambient air condition using this device for three years. Furthermore, we performed the salt deposition test using the small ducts in the same area. The ambient air including sea salt flows in the duct and the sea salt deposits on the test specimen put on the duct inner surface. We took out the specimen after certain time and measured the salt amount on the test specimen. Using these data, we obtained the relation between the salt deposition and the time on this ambient condition. The results of this study are useful to evaluate the SCC of the canister. (author)

  19. Geomorphology-based interpretation of sedimentation rates from radiodating, lower Passaic River, New Jersey, USA.

    Science.gov (United States)

    Erickson, Michael J; Barnes, Charles R; Henderson, Matthew R; Romagnoli, Robert; Firstenberg, Clifford E

    2007-04-01

    Analysis of site geomorphology and sedimentation rates as an indicator of long-term bed stability is central to the evaluation of remedial alternatives for depositional aquatic environments. In conjunction with various investigations of contaminant distribution, sediment dynamics, and bed stability in the Passaic River Estuary, 121 sediment cores were collected in the early 1990s from the lower 9.7 km of the Passaic River and analyzed for lead-210 (210Pb), cesium-137 (137Cs), and other analytes. This paper opportunistically uses the extensive radiochemical dataset to examine the spatial patterns of long-term sedimentation rates in, and associated geomorphic aspects of, this area of the river. For the purposes of computing sedimentation rates, the utility of the 210Pb and 137Cs depositional profiles was assessed to inform appropriate interpretation. Sedimentation rates were computed for 90 datable cores by 3 different methods, depending on profile utility. A sedimentation rate of 0 was assigned to 17 additional cores that were not datable and for which evidence of no deposition exists. Sedimentation patterns were assessed by grouping results within similar geomorphic areas, delineated through inspection of bathymetric data. On the basis of channel morphology, results reflect expected patterns, with the highest sedimentation rates observed along point bars and channel margins. The lowest rates of sedimentation (and the largest percentage of undatable cores) were observed in the areas along the outer banks of channel bends. Increasing sedimentation rates from upstream to downstream were noted. Average and median sedimentation rates were estimated to be 3.8 and 3.7 cm/y, respectively, reflecting the highly depositional nature of the Passaic River estuary. This finding is consistent with published descriptions of long-term geomorphology for Atlantic Coastal Plain estuaries.

  20. The use of two microbiotests to evaluate the toxicity of sediment from ...

    African Journals Online (AJOL)

    The release of contaminants into the aquatic environment and the subsequent accumulation in sediment is a specific area of ... The Ostracodtoxkit F using the species Heterocypris incongruens has ... the top 2 cm of the river bed with an inert plastic scoop, as .... of pollution, such as hydrocarbons and pesticides, ostracods.

  1. Orientation study of northern Arkansas. National Uranium Resource Evaluation program. Hydrogeochemical and stream-sediment reconnaissance

    International Nuclear Information System (INIS)

    Steele, K.F.

    1982-08-01

    Samples of ground water, stream water, and sediment were collected at 335 sites for an orientation study of northern Arkansas. Each stream site consisted of both sediment and stream water (if available), and each sediment sample was sieved to produce four size fractions for analysis. The orientation area included all or parts of Benton, Carroll, Madison, and Washington Counties. Several black shales, including the Chattanooga Shale, crop out in this area, and the Sylamore Sandstone Member has local radiation anomalies. The following analyses were performed for all water samples (both ground water and stream water): pH, conductivity, total alkalinity, temperature, nitrate, ammonia, phosphate and sulfate. Additional water was collected, filtered, and reacted with a resin that was then analyzed by neutron activation analysis for U, Br, Cl, F, Mn, Na, Al, and Dy. In addition, ground water samples were analyzed for He. The stream sediments were analyzed by neutron activation for U, Th, Hf, Ce, Fe, Mn, Sc, Ti, V, Al, Dy, Eu, La, Sm, Yb, and Lu

  2. New element for optimizing the functioning of sediment traps

    Science.gov (United States)

    Schwindt, Sebastian; Franca, Mário; Schleiss, Anton

    2017-04-01

    Sediment traps protect urban areas against excessive sediment transport during hazardous floods and consist typically of a retention basin with an open sediment check dam at the downstream end. The design, as well as the morphological processes within the retention basin, were analyzed by several authors. With regard to open sediment check dams two types of triggering mechanisms for the initiation of sediment retention can be distinguished: (1) mechanical and (2) hydraulic clogging of the structure. Recent studies have shown that outlet structures combining both clogging principles may be considered to avoid undesired self-flushing. Further elements of check dams are conceivable, e.g. for retaining or conveying driftwood. This study analyses experimentally working principles and design criteria of standard elements of sediment traps. Furthermore, it introduces a new structural element to the sediment trap design with a guiding channel in the retention reservoir. Taking into account the natural shape of mountain rivers, the guiding channel has a trapezoidal cross-section shape and a rough but fixed bed. The effect of the guiding channel on sediment deposition pattern and re-mobilization are studied by means of physical model experiments with a standardized hydrograph and variable sediment supply. The results are evaluated by means of zenithal pictures and bedload transport rate, measured at the downstream end of the model. Major advantages of the combined use of both clogging principles include an improved control of the initiation of sediment deposition in order to allow for sediment transfer for small floods and a reduction of hazards related to self-flushing.

  3. Source apportionment and pollution evaluation of heavy metals in water and sediments of Buriganga River, Bangladesh, using multivariate analysis and pollution evaluation indices.

    Science.gov (United States)

    Bhuiyan, Mohammad Amir Hossain; Dampare, Samuel B; Islam, M A; Suzuki, Shigeyuki

    2015-01-01

    Concentrations of heavy metals in water and sediment samples of Buriganga River in the capital city Dhaka, Bangladesh, were studied to understand the level of heavy metals and their source apportionment. The results showed that the mean concentrations of heavy metals both in water and sediment samples were very high and, in most cases, exceeded the permissible limits recommended by the Bangladesh government and other international organizations. Significantly higher concentrations of Pb, Cr, Mn, Co, Ni, Cu, Zn, As, and Cd were found in sediment samples. However, average concentrations of metals both in water and sediment samples were above the effect range median. The heavy metal pollution index (HPI) and degree of contamination (Cd) yielded different results in water samples despite significant correlations between them. The heavy metal evaluation index (HEI) showed strong correlations with HPI and Cd and provided better assessment of pollution levels. The enrichment factor (EF) and geoaccumulation index (Igeo) showed the elevated value of Cr, Pb, and Cd in access of background values. The measured elements were subjected to positive matrix factorization (PMF) and examining correlations in order to explain the content, behavior, and source apportionment of metals. PMF resulted in a successful partitioning of variances into sources related to background geochemistry and contaminant influences. However, the PMF approach successfully demarcated the major sources of metals from tannery, paint, municipal sewage, textiles, and agricultural activities.

  4. Evaluation and assessment of baseline metal contamination in surface sediments from the Bernam River, Malaysia.

    Science.gov (United States)

    Kadhum, Safaa A; Ishak, Mohd Yusoff; Zulkifli, Syaizwan Zahmir

    2016-04-01

    The Bernam River is one of the most important rivers in Malaysia in that it provides water for industries and agriculture located along its banks. The present study was conducted to assess the level of contamination of heavy metals (Cd, Ni, Cr, Sn, and Fe) in surface sediments in the Bernam River. Nine surface sediment samples were collected from the lower, middle, and upper courses of the river. The results indicated that the concentrations of the metals decreased in the order of Sn > Cr > Ni > Fe > Cd (56.35, 14.90, 5.3, 4.6, and 0.62 μg/g(1) dry weight). Bernam River sediments have moderate to severe enrichment for Sn, moderate for Cd, and no enrichment for Cr, Ni, and Fe. The contamination factor (CF) results demonstrated that Cd and Sn are responsible for the high contamination. The pollution load index (PLI), for all the sampling sites, suggests that the sampling stations were generally unpolluted with the exception of the Bagan Tepi Sungai, Sabak Bernam, and Tanjom Malim stations. Multivariate techniques including Pearson's correlation and hierarchical cluster analysis were used to apportion the various sources of the metals. The results suggested that the sediment samples collected from the upper course of the river had lower metal concentrations, while sediments in the middle and lower courses of the river had higher metal concentrations. Therefore, our results can be useful as a baseline data for government bodies to adopt corrective measure on the issues related to heavy metal pollution in the Bernam River in the future.

  5. Early diagenesis in the sediments of the Congo deep-sea fan dominated by massive terrigenous deposits: Part III - Sulfate- and methane- based microbial processes

    Science.gov (United States)

    Pastor, L.; Toffin, L.; Decker, C.; Olu, K.; Cathalot, C.; Lesongeur, F.; Caprais, J.-C.; Bessette, S.; Brandily, C.; Taillefert, M.; Rabouille, C.

    2017-08-01

    Geochemical profiles (SO42-, H2S, CH4, δ13CH4) and phylogenetic diversity of Archaea and Bacteria from two oceanographic cruises dedicated to the lobes sediments of the Congo deep-sea fan are presented in this paper. In this area, organic-rich turbidites reach 5000 m and allow the establishment of patchy cold-seep-like habitats including microbial mats, reduced sediments, and vesicomyid bivalves assemblages. These bivalves live in endosymbiosis with sulfur-oxidizing bacteria and use sulfides to perform chemosynthesis. In these habitats, unlike classical abyssal sediments, anoxic processes are dominant. Total oxygen uptake fluxes and methane fluxes measured with benthic chambers are in the same range as those of active cold-seep environments, and oxygen is mainly used for reoxidation of reduced compounds, especially in bacterial mats and reduced sediments. High concentrations of methane and sulfate co-exist in the upper 20 cm of sediments, and evidence indicates that sulfate-reducing microorganisms and methanogens co-occur in the shallow layers of these sediments. Simultaneously, anaerobic oxidation of methane (AOM) with sulfate as the electron acceptor is evidenced by the presence of ANMEs (ANaerobic MEthanotroph). Dissolved sulfide produced through the reduction of sulfate is reoxidized through several pathways depending on the habitat. These pathways include vesicomyid bivalves uptake (adults or juveniles in the bacterial mats habitats), reoxidation by oxygen or iron phases within the reduced sediment, or reoxidation by microbial mats. Sulfide uptake rates by vesicomyids measured in sulfide-rich sea water (90±18 mmol S m-2 d-1) were similar to sulfide production rates obtained by modelling the sulfate profile with different bioirrigation constants, highlighting the major control of vesicomyids on sulfur cycle in their habitats.

  6. Physical Model-Based Investigation of Reservoir Sedimentation Processes

    Directory of Open Access Journals (Sweden)

    Cheng-Chia Huang

    2018-03-01

    Full Text Available Sedimentation is a serious problem in the operations of reservoirs. In Taiwan, the situation became worse after the Chi-Chi Earthquake recorded on 21 September 1999. The sediment trap efficiency in several regional reservoirs has been sharply increased, adversely affecting the operations on water supplies. According to the field record, the average annual sediment deposition observed in several regional reservoirs in Taiwan has been increased. For instance, the typhoon event recorded in 2008 at the Wushe Reservoir, Taiwan, produced a 3 m sediment deposit upstream of the dam. The remaining storage capacity in the Wushe Reservoir was reduced to 35.9% or a volume of 53.79 million m3 for flood water detention in 2010. It is urgent that research should be conducted to understand the sediment movement in the Wushe Reservoir. In this study, a scale physical model was built to reproduce the flood flow through the reservoir, investigate the long-term depositional pattern, and evaluate sediment trap efficiency. This allows us to estimate the residual life of the reservoir by proposing a modification of Brune’s method. It can be presented to predict the lifespan of Taiwan reservoirs due to higher applicability in both the physical model and the observed data.

  7. In situ high-resolution evaluation of labile arsenic and mercury in sediment of a large shallow lake

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Chao; Yao, Yu; Wang, Peifang; Hou, Jun; Qian, Jin; Yuan, Ye; Fan, Xiulei

    2016-01-15

    The precise evaluation of arsenic (As) and mercury (Hg) bioavailability in sediment is crucial to controlling As and Hg contamination, but traditional ex situ measurements hamper comprehensive analysis of labile As and Hg in sediment. In this study, we characterized in situ labile As and Hg in sediment of Lake Hongze using the zirconium (Zr) oxide diffusive gradients in thin films (DGT) technique and 3-mercaptopropyl functionalized silica gel DGT, respectively. The concentrations of DGT-labile As and Hg in the sediment profiles were found to exhibit considerable variation, ranging from 0.15 to 4.15 μg L{sup −1} for As and from 0.04 to 1.35 μg L{sup −1} for Hg. As and Hg flux values, calculated based on the concentration gradients measured from the DGT profiles for both the overlying water and sediment close to the sediment–water interface, were used to determine the contamination status of As and Hg. Flux values of As and Hg were between − 0.066 and 0.067 ng cm{sup −2} d{sup −1} and between − 0.0187 and 0.0181 ng cm{sup −2} d{sup −1}, respectively. The GNU's Not Unix R (GNU R) programming language was used to identify outliers of As and Hg at various depths at the sampling sites. The results indicate that the sites with the most outliers were all located in the regions that were seriously affected by contaminants from the Huai River. The DGT-labile As and Hg concentrations in the 0–30 mm layer were found to be significantly correlated with concentrations of labile As and Hg, total dissolved As and Hg, and total As and Hg in the overlying water, as indicated by ex situ measurements. Results show that DGT is a reliable and high-resolution technique that can be used for in situ monitoring of the labile fractions of As and Hg in sediment in fresh water bodies. - Graphical abstract: The principle of DGT is based on the diffusion of dissolved species through a well-defined gel and subsequent accumulation on an ion-exchange resin. A diffusion

  8. In situ high-resolution evaluation of labile arsenic and mercury in sediment of a large shallow lake

    International Nuclear Information System (INIS)

    Wang, Chao; Yao, Yu; Wang, Peifang; Hou, Jun; Qian, Jin; Yuan, Ye; Fan, Xiulei

    2016-01-01

    The precise evaluation of arsenic (As) and mercury (Hg) bioavailability in sediment is crucial to controlling As and Hg contamination, but traditional ex situ measurements hamper comprehensive analysis of labile As and Hg in sediment. In this study, we characterized in situ labile As and Hg in sediment of Lake Hongze using the zirconium (Zr) oxide diffusive gradients in thin films (DGT) technique and 3-mercaptopropyl functionalized silica gel DGT, respectively. The concentrations of DGT-labile As and Hg in the sediment profiles were found to exhibit considerable variation, ranging from 0.15 to 4.15 μg L −1 for As and from 0.04 to 1.35 μg L −1 for Hg. As and Hg flux values, calculated based on the concentration gradients measured from the DGT profiles for both the overlying water and sediment close to the sediment–water interface, were used to determine the contamination status of As and Hg. Flux values of As and Hg were between − 0.066 and 0.067 ng cm −2 d −1 and between − 0.0187 and 0.0181 ng cm −2 d −1 , respectively. The GNU's Not Unix R (GNU R) programming language was used to identify outliers of As and Hg at various depths at the sampling sites. The results indicate that the sites with the most outliers were all located in the regions that were seriously affected by contaminants from the Huai River. The DGT-labile As and Hg concentrations in the 0–30 mm layer were found to be significantly correlated with concentrations of labile As and Hg, total dissolved As and Hg, and total As and Hg in the overlying water, as indicated by ex situ measurements. Results show that DGT is a reliable and high-resolution technique that can be used for in situ monitoring of the labile fractions of As and Hg in sediment in fresh water bodies. - Graphical abstract: The principle of DGT is based on the diffusion of dissolved species through a well-defined gel and subsequent accumulation on an ion-exchange resin. A diffusion gel and a filter membrane (to

  9. Evaluation of tribological wear and corrosion in coatings of diamalloy 4060NS deposited by thermal spray

    Science.gov (United States)

    Acuña R, S. M.; Moreno T, C. M.; Espinosa C, E. J.

    2017-12-01

    Surface engineering seeks the development of new techniques to improve the performance and life of components of machines or industrial facilities, always looking for low costs and the least possible environmental damage. Thermal projection is one of the techniques that is based on the projection of particles of compounds and alloys on properly prepared and heated substrates, these particles are driven by a stream of air passing through an oxyacetylene flame which gives the energy to the process; These coatings give the possibility to improve the properties of the materials or the maintenance of components to maximize the availability of service. In order to reduce the damage caused by wear and corrosion of a low carbon AISI 1020 steel, they were coated with a metal based alloy, studying the effect of the cobalt-chromium-silicon-tungsten carbide alloy coating (DIAMALLLOY 4060 NS). The coating was deposited with two different pressures in the gases supplied to the torch, obtaining two flames and working three thicknesses of coating that oscillate between 100-500μm, according to the number of deposited layers, making use of a projection gun Castolin Eutectic. Powder and substrate characterization was performed using X-Ray Diffraction (XRD) techniques, X-Ray Fluorescence (XRF), Scanning Electron Microscopy (SEM), spark emission spectroscopy and metallographic analysis. The results confirm the chemical nature and structure of the powder of the alloy and the substrate to be used, in addition, the thermal stability of the system was verified. The evaluation of the adhesion of the deposited layers was carried out by the implementation of pull-off tests according to ASTM D4541, in order to determine the type of failure that is presented. Mechanical wear was determined using a MT/60/NI microtest tribometer while electrochemical tests were performed using a suitable experimental unit for this purpose, confirming that the substrate exhibits lower wear levels when coated with

  10. Evaluation of experimental studies on technetium transfers to sediments and benthic marine species, and comparison with in situ data

    Energy Technology Data Exchange (ETDEWEB)

    Aprosi, G [Electricite de France, 78 - Chatou; Masson, M [Commisariat a l' Energie Atomique, Institut de Protection et de Surete Nucleaire, 50 - Cherbourg (France)

    1984-01-01

    To obtain basic information for the evaluation of the radiological impact of technetium (Tc) on the marine environment, investigations are performed by different laboratories. Technetium is not a natural element and the main source of production is the nuclear fuel cycle. Under anoxic conditions, in presence of reducing sediments, the distribution coefficients are very high (Ksub(D)=10/sup 3/). Concentration factors from water to species are mostly very low (FC 1 to 10); however, concentration factors up to 1000 have been observed for a few species such as macrophytic brown algae, worms and lobster. Biochemical analysis shows that Tc is bound with protein. The transfer factors between sediment and species are very low (FT<0,5). The biological half-life (Tb) was determined in some marine organisms which had accumulated the radionuclide from water-contamined food or from sediments. The loss is biphasic in storage organs (liver and kidney); uptake in the edible parts is low. Among the parameters studied (light for algae, physico-chemical form of Tc, salinity and temperature) only light and the physico-chemical forms have an effect on the accumulation of technetium. Analyses of /sup 99/Tc concentrations in species collected near the La Hague and Windscale (Sellafield) reprocessing plants confirm the experimental studies. Since sea water is likely to be an oxidant environment, technetium appears as a conservative element.

  11. Catalyst synthesis and evaluation using an integrated atomic layer deposition synthesis–catalysis testing tool

    International Nuclear Information System (INIS)

    Camacho-Bunquin, Jeffrey; Shou, Heng; Marshall, Christopher L.; Aich, Payoli; Beaulieu, David R.; Klotzsch, Helmut; Bachman, Stephen; Hock, Adam; Stair, Peter

    2015-01-01

    An integrated atomic layer deposition synthesis-catalysis (I-ALD-CAT) tool was developed. It combines an ALD manifold in-line with a plug-flow reactor system for the synthesis of supported catalytic materials by ALD and immediate evaluation of catalyst reactivity using gas-phase probe reactions. The I-ALD-CAT delivery system consists of 12 different metal ALD precursor channels, 4 oxidizing or reducing agents, and 4 catalytic reaction feeds to either of the two plug-flow reactors. The system can employ reactor pressures and temperatures in the range of 10 −3 to 1 bar and 300–1000 K, respectively. The instrument is also equipped with a gas chromatograph and a mass spectrometer unit for the detection and quantification of volatile species from ALD and catalytic reactions. In this report, we demonstrate the use of the I-ALD-CAT tool for the synthesis of platinum active sites and Al 2 O 3 overcoats, and evaluation of catalyst propylene hydrogenation activity

  12. Graphene by one-step chemical vapor deposition from ferrocene vapors: Properties and electrochemical evaluation

    Science.gov (United States)

    Pilatos, George; Perdikaki, Anna V.; Sapalidis, Andreas; Pappas, George S.; Giannakopoulou, Tatiana; Tsoutsou, Dimitra; Xenogiannopoulou, Evangelia; Boukos, Nikos; Dimoulas, Athanasios; Trapalis, Christos; Kanellopoulos, Nick K.; Karanikolos, Georgios N.

    2016-02-01

    Growth of few-layer graphene using ferrocene as precursor by chemical vapor deposition is reported. The growth did not involve any additional carbon or catalyst source or external hydrocarbon gases. Parametric investigation was performed using different conditions, namely, varying growth temperature from 600 to1000 °C, and growth duration from 5 min to 3 h, as well as using fast quenching or gradual cooling after the thermal treatment, in order to examine the effect on the quality of the produced graphene. The growth took place on silicon wafers and resulted, under optimal conditions, in formation of graphene with 2-3 layers and high graphitic quality, as evidenced by Raman spectroscopy, with characteristic full width at half maximum of the 2D band of 49.46 cm-1, and I2D/IG and ID/IG intensity ratios of 1.15 and 0.26, respectively. Atomic force microscopy and X-ray photoelectron spectroscopy were employed to further evaluate graphene characteristics and enlighten growth mechanism. Electrochemical evaluation of the developed material was performed using cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge-discharge measurements.

  13. Catalyst synthesis and evaluation using an integrated atomic layer deposition synthesis–catalysis testing tool

    Energy Technology Data Exchange (ETDEWEB)

    Camacho-Bunquin, Jeffrey; Shou, Heng; Marshall, Christopher L. [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Aich, Payoli [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Department of Chemical Engineering, University of Illinois at Chicago, Chicago, Illinois 60607 (United States); Beaulieu, David R.; Klotzsch, Helmut; Bachman, Stephen [Arradiance Inc., Sudbury, Massachusetts 01776 (United States); Hock, Adam [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Department of Chemistry, Illinois Institute of Technology, Chicago, Illinois 60616 (United States); Stair, Peter [Chemical Sciences and Engineering Division, Argonne National Laboratory, Lemont, Illinois 60439 (United States); Department of Chemistry, Northwestern University, Evanston, Illinois 60208 (United States)

    2015-08-15

    An integrated atomic layer deposition synthesis-catalysis (I-ALD-CAT) tool was developed. It combines an ALD manifold in-line with a plug-flow reactor system for the synthesis of supported catalytic materials by ALD and immediate evaluation of catalyst reactivity using gas-phase probe reactions. The I-ALD-CAT delivery system consists of 12 different metal ALD precursor channels, 4 oxidizing or reducing agents, and 4 catalytic reaction feeds to either of the two plug-flow reactors. The system can employ reactor pressures and temperatures in the range of 10{sup −3} to 1 bar and 300–1000 K, respectively. The instrument is also equipped with a gas chromatograph and a mass spectrometer unit for the detection and quantification of volatile species from ALD and catalytic reactions. In this report, we demonstrate the use of the I-ALD-CAT tool for the synthesis of platinum active sites and Al{sub 2}O{sub 3} overcoats, and evaluation of catalyst propylen